Effects of grain dust on lungs prior to and following dust remediation.

Science.gov (United States)

Pahwa, Punam; Dosman, James A; McDuffie, Helen H

2008-12-01

To determine longitudinal estimates of pulmonary function decline in Canadian grain elevator workers before and after dust control by analyzing data collected from five regions of Canada over 15 years. Declines in forced expired volume in one second and forced vital capacity before and after dust control were estimated by using a generalized estimating equations approach. For grain workers who were in the grain industry for 20 or more years both before and after dust control: the mean annual loss of forced expired volume in one second was greatest among current smoking grain workers followed by ex-smokers and nonsmokers, respectively. Similar results were obtained for forced vital capacity. Grain dust control was effective in reducing decline in the lung function measurements among grain workers in all smoking and exposure categories.

Grain elevator workers show work-related pulmonary function changes and dose-effect relationships with dust exposure.

Science.gov (United States)

Corey, P; Hutcheon, M; Broder, I; Mintz, S

1982-01-01

The purpose of this study was to determine whether grain handlers underwent work-related changes in their pulmonary function and, if so, to examine the dose-effect relationships with dust exposure. The pulmonary function of grain handlers was measured at the beginning and end of work shifts over a period of one week, during which their exposure to dust was measured daily. The results showed changes indicative of a within-day obstructive change, in addition to a small restrictive defect occurring over the course of a week. Civic outside labourers who were examined as a control group showed a similar within-week obstructive change without any associated restriction of lung volume. The data on the grain handlers were also used to examine the dose-effect relationships of dust exposure, both on baseline pulmonary function and on within-day changes in these measurements. The baseline flow rates of workers who did not wear a mask were found to vary inversely with their average exposure to respirable dust. In addition, the flow rates underwent a within-day decrease that varied directly with their corresponding exposure to respirable dust and was unrelated to mask wearing. The median of the slopes for this relationship indicated that 50% of the subjects had a decrease of at least 923 ml/s in the value of their Vmax50%VC for each 1 mg/m3 increase in the concentration of respirable dust. Non-respirable dust did not have a measurable effect either on the baseline or the within-day changes in pulmonary function. The acute changes were unaffected by age, duration of employment, or extent of smoking. PMID:7138793

Exposure to grain dust and microbial components in the Norwegian grain and compound feed industry.

Science.gov (United States)

Halstensen, Anne Straumfors; Heldal, Kari Kulvik; Wouters, Inge M; Skogstad, Marit; Ellingsen, Dag G; Eduard, Wijnand

2013-11-01

The aim of this study was to extensively characterize grain workers' personal exposure during work in Norwegian grain elevators and compound feed mills, to identify differences in exposures between the workplaces and seasons, and to study the correlations between different microbial components. Samples of airborne dust (n = 166) were collected by full-shift personal sampling during work in 20 grain elevators and compound feed mills during one autumn season and two winter seasons. The personal exposure to grain dust, endotoxins, β-1→3-glucans, bacteria, and fungal spores was quantified. Correlations between dust and microbial components and differences between workplaces and seasons were investigated. Determinants of endotoxin and β-1→3-glucan exposure were evaluated by linear mixed-effect regression modeling. The workers were exposed to an overall geometric mean of 1.0mg m(-3) inhalable grain dust [geometric standard deviation (GSD) = 3.7], 628 endotoxin units m(-3) (GSD = 5.9), 7.4 µg m(-3) of β-1→3-glucan (GSD = 5.6), 21 × 10(4) bacteria m(-3) (GSD = 7.9) and 3.6 × 10(4) fungal spores m(-3) (GSD = 3.4). The grain dust exposure levels were similar across workplaces and seasons, but the microbial content of the grain dust varied substantially between workplaces. Exposure levels of all microbial components were significantly higher in grain elevators compared with all other workplaces. The grain dust exposure was significantly correlated (Pearson's r) with endotoxin (rp = 0.65), β-1→3-glucan (rp = 0.72), bacteria (rp = 0.44) and fungal spore (rp = 0.48) exposure, whereas the explained variances were strongly dependent on the workplace. Bacteria, grain dust, and workplace were important determinants for endotoxin exposure, whereas fungal spores, grain dust, and workplace were important determinants for β-1→3-glucan exposure. Although the workers were exposed to a relatively low mean dust level, the microbial exposure was high. Furthermore, the

Size Distribution and Rate of Dust Generated During Grain Elevator Handling

Science.gov (United States)

Dust generated during grain handling is an air pollutant that produces safety and health hazards. This study was conducted to characterize the particle size distribution (PSD) of dust generated during handling of wheat and shelled corn in the research elevator of the USDA Grain Marketing and Product...

Stored-grain insect population commingling densities in wheat and corn from pilot-scale bucket elevator boots

Science.gov (United States)

Grain elevator boot and pit areas facilitate the commingling of insects with the grain moving through the elevator leg. A removable boot was developed to facilitate residual grain removal and preservation in the boot and to quantify the commingling magnitude as a function of stored-product insect de...

Effects of elevated ozone, carbon dioxide, and the combination of both on the grain quality of Chinese hybrid rice

International Nuclear Information System (INIS)

Wang, Yunxia; Song, Qiling; Frei, Michael; Shao, Zaisheng; Yang, Lianxin

2014-01-01

The effects of CO 2 and/or O 3 elevation on rice grain quality were investigated in chamber experiments with gas fumigation performed from transplanting until maturity in 2011 and 2012. Compared with the control (current CO 2 and O 3 concentration), elevated CO 2 caused a tendency of an increase in grain chalkiness and a decrease in mineral nutrient concentrations. In contrast, elevated O 3 significantly increased grain chalkiness and the concentrations of essential nutrients, while changes in starch pasting properties indicated a trend of deterioration in the cooking and eating quality. In the combination of elevated CO 2 and O 3 treatment, only chalkiness degree was significantly affected. It is concluded that the O 3 concentration projected for the coming few decades will have more substantial effects on grain quality of Chinese hybrid rice than the projected high CO 2 concentration alone, and the combination of two gases caused fewer significant changes in grain quality than individual gas treatments. - Highlights: • We investigated the effects of carbon dioxide and/or ozone elevation on rice grain quality. • Elevated ozone concentration had substantial effects on grain quality under current carbon dioxide concentration. • Elevated carbon dioxide concentration mitigated the impact of elevated ozone concentration on rice grain quality. - Exposure of Chinese hybrid rice to elevated ozone and CO 2 during growth causes fewer changes in grain quality than ozone exposure alone

77 FR 33490 - Long Elevator & Machine Company, Inc., Including Workers Whose Unemployment Insurance (UI) Wages...

Science.gov (United States)

2012-06-06

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-80,525] Long Elevator & Machine Company, Inc., Including Workers Whose Unemployment Insurance (UI) Wages Were Reported Through Kone, Inc... former workers of Long Elevator & Machine Company, Inc., including workers whose unemployment insurance...

Frequent Occupational Exposure to Fusarium Mycotoxins of Workers in the Swiss Grain Industry

Directory of Open Access Journals (Sweden)

Hélène Niculita-Hirzel

2016-12-01

Full Text Available Type B trichotecens such as deoxynivalenol (DON, 3-acetyldeoxynivalenol (3-ADON, 15-acetyldeoxynivalenol (15-ADON, nivalenol (NIV and zearalenone (ZEN are mycotoxins contaminating wheat and wheat dust. Mycotoxins are toxic upon ingestion and considered potentially toxic when inhaled. Whereas dietary exposure to mycotoxins is controlled in food, data on occupational exposure by inhalation by grain workers are scarce. The objectives of this study were to determine the incidence of DON, 3-ADON, 15-ADON, NIV and ZEN in aerosols generated during grain harvesting and unloading and the risk of exposure of grain workers. Aerosols were collected during the threshing of 78 winter wheat fields and grain unloading of 59 grain lots in six grain terminals in the Vaud region (Switzerland. The samples represented the diversity of the winter wheat cultivar and of the farming system (88 treated with fungicides, 46 untreated. Using a HPLC MS/MS method developed to quantify mycotoxins in aerosols, we report that the mycotoxin content of aerosols was not affected by the wheat cultivars or farming system, but that the incidence of the mycotoxins differed between activities. While wheat harvesting generated on average 28, 20 and 1 ng·m−3 of DON, NIV and ZEN, respectively, grain unloading generated 53, 46 and 4 ng·m−3. Personal sampling revealed that working in a cab was an efficient protective measure. However, it was not sufficient to avoid chronic exposure to multiple mycotoxins. The most exposed activity was the cleaning, exposing workers to DON, NIV and ZEN at concentrations as high as 65, 59 and 3 ng·m−3. These data provide valuable information for future studies of mycotoxin toxicity at relevant concentrations on respiratory health.

Grain dust and respiratory health in South African milling workers.

Science.gov (United States)

Bachmann, M; Myers, J E

1991-01-01

Respiratory health was investigated in 224 grain milling workers. The likelihood of respiratory symptoms and chronic airflow limitation was raised for workers exposed to dust independent of the effects of smoking. Smokers were more likely than non-smokers to respond to a bronchodilator at the end of the working week. Dust was more strongly associated with most abnormal outcomes than was smoking. Subjective categories of exposure to dust were more strongly associated with most abnormal outcomes than were objective categories. The prevalence of all symptoms at the time of a survey conducted at the mill six years before was higher in workers who subsequently left the mill than in those who remained employed although the differences were not significant. PMID:1931723

77 FR 62265 - Long Elevator & Machine Company, Inc., Including Workers Whose Wages Were Reported Through Kone...

Science.gov (United States)

2012-10-12

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-80,525] Long Elevator & Machine... Determination Regarding Application for Reconsideration for workers and former workers of Long Elevator... (hereafter referred to as Long Elevator & Machine Company or the subject firm). The Department's Notice was...

Comparison of dust related respiratory effects in Dutch and Canadian grain handling industries: a pooled analysis.

Science.gov (United States)

Peelen, S J; Heederik, D; Dimich-Ward, H D; Chan-Yeung, M; Kennedy, S M

1996-08-01

Four previously conducted epidemiological studies in more than 1200 grain workers were used to compare exposure-response relations between exposure to grain dust and respiratory health. The studies included Dutch workers from an animal feed mill and a transfer grain elevator and Canadian workers from a terminal grain elevator and the docks. Relations between forced expiratory volume in one second (FEV1) and exposure were analysed with multiple regression analysis corrected for smoking, age, and height. Exposure variables examined included cumulative and current dust exposure and the numbers of years a subject was employed in the industry. Sampling efficiencies of the Dutch and Canadian measurement techniques were compared in a pilot study. Results of this study were used to correct slopes of exposure-response relations for differences in dust fractions sampled by Dutch and Canadian personal dust samplers. Negative exposure-response relations were shown for regressions of FEV1 on cumulative and current exposure and years employed. Slopes of the exposure-response relations differed by a factor of three to five between industries, apart from results for cumulative exposure. Here the variation in slopes differed by a factor of 100, from -1 to -0.009 ml/mg.y/m3. The variation in slopes between industries reduced to between twofold to fivefold when the Dutch transfer elevator workers were not considered. There was evidence that the small exposure-response slope found for this group is caused by misclassification of exposure and a strong healthy worker effect. Alternative, but less likely explanations for the variation in slopes were differences in exposure concentrations, composition of grain dust, exposure characteristics, and measurement techniques. In conclusion, this study showed moderately similar negative exposure-response relations for four different populations from different countries, despite differences in methods of exposure assessment and exposure estimation.

Work Tasks as Determinants of Grain Dust and Microbial Exposure in the Norwegian Grain and Compound Feed Industry.

Science.gov (United States)

Straumfors, Anne; Heldal, Kari Kulvik; Wouters, Inge M; Eduard, Wijnand

2015-07-01

The grain and compound feed industry entails inevitable risks of exposure to grain dust and its microbial content. The objective of this study was therefore to investigate task-dependent exposure differences in order to create knowledge basis for awareness and exposure reducing measures in the Norwegian grain and compound feed industry. A total of 166 samples of airborne dust were collected by full-shift personal sampling during work in 20 grain elevators and compound feed mills during one autumn season and two winter seasons. The personal exposure to grain dust, endotoxins, β-1→3-glucans, bacteria, and fungal spores was quantified and used as individual outcomes in mixed models with worker nested in company as random effect and different departments and tasks as fixed effects. The exposure levels were highest in grain elevator departments. Exposure to endotoxins was particularly high. Tasks that represented the highest and lowest exposures varied depending on the bioaerosol component. The most important determinants for elevated dust exposure were cleaning and process controlling. Cleaning increased the dust exposure level by a factor of 2.44 of the reference, from 0.65 to 1.58mg m(-3), whereas process controlling increased the dust exposure level by a factor of 2.97, from 0.65 to 1.93mg m(-3). Process controlling was associated with significantly less grain dust exposure in compound feed mills and the combined grain elevators and compound feed mills, than in grain elevators. The exposure was reduced by a factor of 0.18 and 0.22, from 1.93 to 0.34mg m(-3) and to 0.42mg m(-3), respectively, compared with the grain elevators. Inspection/maintenance, cleaning, and grain rotation and emptying were determinants of higher exposure to both endotoxin and β-1→3-glucans. Seed winnowing was in addition a strong determinant for endotoxin, whereas mixing of animal feed implied higher β-1→3-glucan exposure. Cleaning was the only task that contributed significantly to

CREATION OF EXPORT-ORIENTED NETWORK OF GRAIN ELEVATORS IN UKRAINE

Directory of Open Access Journals (Sweden)

D. M. Kozachenko

2017-04-01

Full Text Available Purpose. The scientific paper highlights improving the efficiency of export rail transportation of grain cargoes in Ukraine by introducing shipper routing and concentration of loading at the terminal grain elevators. Methodology. According to the experience of the USA and Canada, one of the most effective ways to reduce costs in the grain to-port supply chain is a shipper routing of the rail traffic. Shipper routing for transportation of grain cargoes involves the concentration of their loading on the multiple junctions. The junctions are proposed to be selected with the use of cluster analysis methods. For the formation of the grain loading concentration areas the authors used methods of set theory and multi-criteria optimization. Findings. Based on agglomerative cluster analysis algorithm, the junctions on a network of Ukrainian railways are selected and the areas of possible concentration of grain loading are formed. DSU-algorithm allowed distinguishing the overlapping and non-overlapping areas of concentration. The problem of selecting non-overlapping areas of the grain loading concentration is formalized as the problem of multiobjective integer programming with boolean variables. The solution of this problem by a modified simplex algorithm allows selecting on the railway network of Ukraine 24 districts of possible grain loading concentration, which cover 70 stations and at minimal additional cost provide routing of about 7.5 million tons of grain per year. Originality. The originality of the work lies in the fact that the authors developed the mathematical procedure for selection of junctions and concentration areas of grain loading at the Ukrainian railway network, taking into account the economic efficiency of the process. Practicalvalue. Application of the developed method of grain loading concentration for the formation of unit trains will significantly reduce the logistics costs in the supply chain of grain to Ukrainian ports for

Postural stability effects of random vibration at the feet of construction workers in simulated elevation.

Science.gov (United States)

Simeonov, P; Hsiao, H; Powers, J; Ammons, D; Kau, T; Amendola, A

2011-07-01

The risk of falls from height on a construction site increases under conditions which degrade workers' postural control. At elevation, workers depend heavily on sensory information from their feet to maintain balance. The study tested two hypotheses: "sensory enhancement"--sub-sensory (undetectable) random mechanical vibrations at the plantar surface of the feet can improve worker's balance at elevation; and "sensory suppression"--supra-sensory (detectable) random mechanical vibrations can have a degrading effect on balance in the same experimental settings. Six young (age 20-35) and six aging (age 45-60) construction workers were tested while standing in standard and semi-tandem postures on instrumented gel insoles. The insoles applied sub- or supra-sensory levels of random mechanical vibrations to the feet. The tests were conducted in a surround-screen virtual reality system, which simulated a narrow plank at elevation on a construction site. Upper body kinematics was assessed with a motion-measurement system. Postural stability effects were evaluated by conventional and statistical mechanics sway measures, as well as trunk angular displacement parameters. Analysis of variance did not confirm the "sensory enhancement" hypothesis, but provided evidence for the "sensory suppression" hypothesis. The supra-sensory vibration had a destabilizing effect, which was considerably stronger in the semi-tandem posture and affected most of the sway variables. Sensory suppression associated with elevated vibration levels on a construction site may increase the danger of losing balance. Construction workers at elevation, e.g., on a beam or narrow plank might be at increased risk of fall if they can detect vibrations under their feet. To reduce the possibility of losing balance, mechanical vibration to supporting structures used as walking/working surfaces should be minimized when performing construction tasks at elevation. Published by Elsevier Ltd.

Changes in Whole-Plant Metabolism during the Grain-Filling Stage in Sorghum Grown under Elevated CO2 and Drought.

Science.gov (United States)

De Souza, Amanda P; Cocuron, Jean-Christophe; Garcia, Ana Carolina; Alonso, Ana Paula; Buckeridge, Marcos S

2015-11-01

Projections indicate an elevation of the atmospheric CO2 concentration ([CO2]) concomitant with an intensification of drought for this century, increasing the challenges to food security. On the one hand, drought is a main environmental factor responsible for decreasing crop productivity and grain quality, especially when occurring during the grain-filling stage. On the other hand, elevated [CO2] is predicted to mitigate some of the negative effects of drought. Sorghum (Sorghum bicolor) is a C4 grass that has important economical and nutritional values in many parts of the world. Although the impact of elevated [CO2] and drought in photosynthesis and growth has been well documented for sorghum, the effects of the combination of these two environmental factors on plant metabolism have yet to be determined. To address this question, sorghum plants (cv BRS 330) were grown and monitored at ambient (400 µmol mol(-1)) or elevated (800 µmol mol(-1)) [CO2] for 120 d and subjected to drought during the grain-filling stage. Leaf photosynthesis, respiration, and stomatal conductance were measured at 90 and 120 d after planting, and plant organs (leaves, culm, roots, prop roots, and grains) were harvested. Finally, biochemical composition and intracellular metabolites were assessed for each organ. As expected, elevated [CO2] reduced the stomatal conductance, which preserved soil moisture and plant fitness under drought. Interestingly, the whole-plant metabolism was adjusted and protein content in grains was improved by 60% in sorghum grown under elevated [CO2]. © 2015 American Society of Plant Biologists. All Rights Reserved.

The impact of elevated CO2 and temperature on grain quality of rice grown under open-air field conditions.

Science.gov (United States)

Jing, Liquan; Wang, Juan; Shen, Shibo; Wang, Yunxia; Zhu, Jianguo; Wang, Yulong; Yang, Lianxin

2016-08-01

Rising atmospheric CO2 is accompanied by global warming. However, interactive effects of elevated CO2 and temperature have not been well studied on grain quality of rice. A japonica cultivar was grown in the field using a free-air CO2 enrichment facility in combination with a canopy air temperature increase system in 2014. The gas fumigation (200 µmol mol(-1) above ambient CO2 ) and temperature increase (1 °C above ambient air temperature) were performed from tillering until maturity. Compared with the control (ambient CO2 and air temperature), elevated CO2 increased grain length and width as well as grain chalkiness but decreased protein concentrations. In contrast, the increase in canopy air temperature had less effect on these parameters except for grain chalkiness. The starch pasting properties of rice flour and taste analysis of cooked rice indicated that the palatability of rice was improved by CO2 and/or temperature elevation, with the combination of the two treatments showing the most significant changes compared with ambient rice. It is concluded that projected CO2 in 2050 may have larger effects on rice grain quality than the projected temperature increase. Although deterioration in milling suitability, grain appearance and nutritional quality can be expected, the taste of cooked rice might be better in the future environment. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Effects of elevated O3 exposure on nutrient elements and quality of winter wheat and rice grain in Yangtze River Delta, China

International Nuclear Information System (INIS)

Zheng, Feixiang; Wang, Xiaoke; Zhang, Weiwei; Hou, Peiqiang; Lu, Fei; Du, Keming; Sun, Zhongfu

2013-01-01

With the open-top chambers (OTCs) in situ in Yangtze River Delta, China in 2007 and 2008, the effects of elevated O 3 exposure on nutrient elements and quality of winter wheat and rice grain were investigated. Grain yield per plant of winter wheat and rice declined in both years. The N and S concentrations increased under elevated O 3 exposure in both years and C–N ratios decreased significantly. The concentrations of K, Ca, Mg, P, Mn, Cu and Zn in winter wheat and the concentrations of Mg, K, Mn and Cu in rice increased. The concentrations of protein, amino acid and lysine in winter wheat and rice increased and the concentration of amylose decreased. The increase in the nutrient concentration was less than the reduction of grain yield in both winter wheat and rice, and, hence, the absolute amount of the nutrients was reduced by elevated O 3 . -- Highlights: •The nutrient elements and quality of winter wheat and rice grain response to ozone had been investigated for two years in China. •Grain yield per plant of winter wheat and rice were reduced in both years. •The extent of ozone impact on the nutrient elements concentrations of winter wheat and rice were different. •The concentrations of protein, amino acid and lysine increased but the concentrations of amylose decreased. •The absolute amount of the nutrients was reduced by elevated O 3 . -- The nutrient elements and quality of winter wheat and rice grain were seriously affected under the elevated O 3 exposure

Safety in Elevators and Grain Handling Facilities. Module SH-27. Safety and Health.

Science.gov (United States)

Center for Occupational Research and Development, Inc., Waco, TX.

This student module on safety in elevators and grain handling facilities is one of 50 modules concerned with job safety and health. Following the introduction, 15 objectives (each keyed to a page in the text) the student is expected to accomplish are listed (e.g., Explain how explosion suppression works). Then each objective is taught in detail,…

Airborne and Grain Dust Fungal Community Compositions Are Shaped Regionally by Plant Genotypes and Farming Practices

Science.gov (United States)

Pellissier, Loïc; Oppliger, Anne; Hirzel, Alexandre H.; Savova-Bianchi, Dessislava; Mbayo, Guilain; Mascher, Fabio; Kellenberger, Stefan

2016-01-01

Chronic exposure to airborne fungi has been associated with different respiratory symptoms and pathologies in occupational populations, such as grain workers. However, the homogeneity in the fungal species composition of these bioaerosols on a large geographical scale and the different drivers that shape these fungal communities remain unclear. In this study, the diversity of fungi in grain dust and in the aerosols released during harvesting was determined across 96 sites at a geographical scale of 560 km2 along an elevation gradient of 500 m by tag-encoded 454 pyrosequencing of the internal transcribed spacer (ITS) sequences. Associations between the structure of fungal communities in the grain dust and different abiotic (farming system, soil characteristics, and geographic and climatic parameters) and biotic (wheat cultivar and previous crop culture) factors were explored. These analyses revealed a strong relationship between the airborne and grain dust fungal communities and showed the presence of allergenic and mycotoxigenic species in most samples, which highlights the potential contribution of these fungal species to work-related respiratory symptoms of grain workers. The farming system was the major driver of the alpha and beta phylogenetic diversity values of fungal communities. In addition, elevation and soil CaCO3 concentrations shaped the alpha diversity, whereas wheat cultivar, cropping history, and the number of freezing days per year shaped the taxonomic beta diversity of these communities. PMID:26826229

Effect of elevated [CO2 ] on yield, intra-plant nutrient dynamics, and grain quality of rice cultivars in Eastern India.

Science.gov (United States)

Jena, Usha Rani; Swain, Dillip Kumar; Hazra, K K; Maity, Mrinal K

2018-05-16

Climate models predict an increase in global temperature in response to a doubling of atmospheric [CO 2 ] that may impact future rice production and quality. In this study, the effect of elevated [CO 2 ] on yield, nutrient acquisition and utilization, and grain quality of rice genotypes was investigated in subtropical climate of eastern India (Kharagpur). Three environments (open field, ambient, and elevated [CO 2 ]) were tested using four rice cultivars of eastern India. Under elevated [CO 2 ] (25% higher), yield of high yielding cultivars (HYCs) viz. IR 36, Swarna, and Swarna sub1 was significantly reduced (11-13%), whereas the yield increased (6-9%) for Badshabhog, a low-yielding aromatic cultivar. Elevated [CO 2 ] significantly enhanced K uptake (14-21%), but did not influence the uptake of total N and P. The nutrient harvest index and use efficiency values in HYCs were reduced under elevated [CO 2 ] indicating that nutrients translocation from source to sink (grain) was significantly reduced. An increase in alkali spreading value (10%) and reduction in grain protein (2-3%) and iron (5-6%) was also observed upon [CO 2 ] elevation. The study highlights the importance of nutrient management (increasing N rate for HYCs) and selective breeding of tolerant cultivar in minimizing the adverse effect of elevated [CO 2 ] on rice yield and quality. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Grain Handling and Storage.

Science.gov (United States)

Harris, Troy G.; Minor, John

This text for a secondary- or postecondary-level course in grain handling and storage contains ten chapters. Chapter titles are (1) Introduction to Grain Handling and Storage, (2) Elevator Safety, (3) Grain Grading and Seed Identification, (4) Moisture Control, (5) Insect and Rodent Control, (6) Grain Inventory Control, (7) Elevator Maintenance,…

Lymphocyte DNA damage in elevator manufacturing workers in Guangzhou, China.

Science.gov (United States)

Lam, Tai Hing; Zhu, Chang Qi; Jiang, Chao Qiang

2002-03-25

To study the effect of smoking, passive smoking, alcohol drinking, and occupational exposure to low level of benzene on DNA strand breaks in elevator manufacturing workers in Guangzhou, China. Three hundred and fifty-nine workers (252 men and 107 women) of a modern elevator manufacturing factory, 205 were from production departments and 154 from managerial department. Information on the workers' health conditions, smoking, passive smoking, alcohol consumption and occupational exposure history was collected by personal interview. Lymphocyte DNA damage was measured by the Comet assay. None of the women smoked and 20.6% of the men were daily smokers. In non-smokers, the prevalence of passive smoking at work was 25% for men and 11.2% for women, and at home, 37.8 and 48.6%, respectively. Smoking significantly increased tail moment (P<0.001). Daily smokers had the largest tail moment (geometric mean, 95% CI) (0.93 microm (0.81-0.94)), followed by occasional smokers (0.76 microm (0.59-0.95)), ex-smokers (0.70 microm (0.58-0.85)), and never smokers (0.56 microm (0.53-0.60)). Tail moment increased significantly with daily tobacco consumption (cigarettes per day) (r=0.26, P<0.001) after adjusting for age, gender, occupational exposure, passive smoking, and drinking. Analysis of covariance (ANCOVA) showed that smoking (P<0.001), passive smoking at home (P=0.026), occupational exposure (P<0.001), male gender (P<0.001), and age (P=0.001) had independent effects on tail moment, whereas passive smoking at work and alcohol drinking had no significant effect. Smoking, passive smoking at home, male gender, age and occupational exposure independently increased lymphocyte DNA strand breaks. The presence of excess DNA damage under low level of occupational exposure to benzene or other solvents suggest that the current allowance concentrations may not be safe to prevent genotoxicity.

Airborne and Grain Dust Fungal Community Compositions Are Shaped Regionally by Plant Genotypes and Farming Practices.

Science.gov (United States)

Pellissier, Loïc; Oppliger, Anne; Hirzel, Alexandre H; Savova-Bianchi, Dessislava; Mbayo, Guilain; Mascher, Fabio; Kellenberger, Stefan; Niculita-Hirzel, Hélène

2016-01-29

Chronic exposure to airborne fungi has been associated with different respiratory symptoms and pathologies in occupational populations, such as grain workers. However, the homogeneity in the fungal species composition of these bioaerosols on a large geographical scale and the different drivers that shape these fungal communities remain unclear. In this study, the diversity of fungi in grain dust and in the aerosols released during harvesting was determined across 96 sites at a geographical scale of 560 km(2) along an elevation gradient of 500 m by tag-encoded 454 pyrosequencing of the internal transcribed spacer (ITS) sequences. Associations between the structure of fungal communities in the grain dust and different abiotic (farming system, soil characteristics, and geographic and climatic parameters) and biotic (wheat cultivar and previous crop culture) factors were explored. These analyses revealed a strong relationship between the airborne and grain dust fungal communities and showed the presence of allergenic and mycotoxigenic species in most samples, which highlights the potential contribution of these fungal species to work-related respiratory symptoms of grain workers. The farming system was the major driver of the alpha and beta phylogenetic diversity values of fungal communities. In addition, elevation and soil CaCO3 concentrations shaped the alpha diversity, whereas wheat cultivar, cropping history, and the number of freezing days per year shaped the taxonomic beta diversity of these communities. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Temporal changes in stored-product insect populations associated with boot, pit, and load-out areas of grain elevators and feed mills

Science.gov (United States)

Commercial grain elevator and feed mill facilities can quickly become infested with stored-product insect pests, compromising the protection of the raw and processed cereal products stored at each facility type. Grain facilities of each type were sampled monthly for adults of stored-product insects ...

Grain dust and the lungs.

Science.gov (United States)

Chan-Yeung, M.; Ashley, M. J.; Grzybowski, S.

1978-01-01

Grain dust is composed of a large number of materials, including various types of grain and their disintegration products, silica, fungi, insects and mites. The clinical syndromes described in relation to exposure to grain dust are chronic bronchitis, grain dust asthma, extrinsic allergic alveolitis, grain fever and silo-filler's lung. Rhinitis and conjunctivitis are also common in grain workers. While the concentration and the quality of dust influence the frequency and the type of clinical syndrome in grain workers, host factors are also important. Of the latter, smoking is the most important factor influencing the frequency of chronic bronchitis. The role of atopy and of bronchial hyperreactivity in grain dust asthma has yet to be assessed. Several well designed studies are currently being carried out in North America not only to delineate the frequency of the respiratory abnormalities, the pathogenetic mechanisms and the host factors, but also to establish a meaningful threshold limit concentration for grain dust. Images p1272-a PMID:348288

The role of endotoxin in grain dust-induced lung disease.

Science.gov (United States)

Schwartz, D A; Thorne, P S; Yagla, S J; Burmeister, L F; Olenchock, S A; Watt, J L; Quinn, T J

1995-08-01

To identify the role of endotoxin in grain dust-induced lung disease, we conducted a population-based, cross-sectional investigation among grain handlers and postal workers. The study subjects were selected by randomly sampling all grain facilities and post offices within 100 miles of Iowa City. Our study population consisted of 410 grain workers and 201 postal workers. Grain workers were found to be exposed to higher concentrations of airborne dust (p = 0.0001) and endotoxin (p = 0.0001) when compared with postal workers. Grain workers had a significantly higher prevalence of work-related (cough, phlegm, wheezing, chest tightness, and dyspnea) and chronic (usual cough or phlegm production) respiratory symptoms than postal workers. Moreover, after controlling for age, gender, and cigarette smoking status, work-related respiratory symptoms were strongly associated with the concentration of endotoxin in the bioaerosol in the work setting. The concentration of total dust in the bioaerosol was marginally related to these respiratory problems. After controlling for age, gender, and cigarette smoking status, grain workers were found to have reduced spirometric measures of airflow (FEV1, FEV1/FVC, and FEF25-75) and enhanced airway reactivity to inhaled histamine when compared with postal workers. Although the total dust concentration in the work environment appeared to have little effect on these measures of airflow obstruction, higher concentrations of endotoxin in the bioaerosol were associated with diminished measures of airflow and enhanced bronchial reactivity. Our results indicate that the concentration of endotoxin in the bioaerosol may be particularly important in the development of grain dust-induced lung disease.

Lead-elevated activity of xanthine oxidase in lead-exposed workers

Directory of Open Access Journals (Sweden)

Sławomir Kasperczyk

2013-04-01

Full Text Available Background: The aim of the present study was to explore the connection between lead toxicity and the activity of xanthine oxidase (XO. In addition, we indicated the uric acid (UA and creatinine levels and concentration of erythrocyte malondialdehyde (MDA to estimate oxidative stress intensity. Materials and Methods: The examined group consisted of 125 healthy male employees of zinc and lead works. The examined group was divided into tertiles according to blood lead levels. In the collected blood samples, concentrations of lead-exposure indices, UA, creatinine, and MDA as well as activity of XO were measured concomitantly. The control group consisted of 32 healthy male administrative workers who were exposed to lead only environmentally. Results: XO activity and MDA level were significantly elevated in all tertiles compared to the control group. Creatinine level was significantly elevated in the medium and high tertiles. However, the level of UA was significantly elevated in the high tertile, while in the low and medium tertile only a tendency toward higher values was observed. Conclusions: Occupational exposure to lead induces activity of XO. This induction may contribute to the observed simultaneously increased oxidative stress, measured as MDA level, and the increased level of UA. Med Pr 2013;64(2:175–180

Nasal lavage cellularity, grain dust, and airflow obstruction.

Science.gov (United States)

Blaski, C A; Watt, J L; Quinn, T J; Thorne, P S; Schwartz, D A

1996-04-01

To evaluate the clinical utility of nasal lavage (NL), we performed post-work shift NL on 172 grain workers and 78 postal worker control subjects. The grain worker group included a higher percentage of current smokers (25.7% vs 16.7%) and a lower percentage of former smokers (21.15% vs 35.9%) compared with the postal workers. The control subjects included more female workers and were slightly older than the grain workers. Compared with the postal workers, the grain workers were exposed to significantly greater concentrations of total dust (0.1 +/- 0.0 vs 6.8 +/- 1.4 mg/m3; mean +/- SEM) and total endotoxin (4.3 +/- 0.8 vs 2,372.4 +/- 653.8 endotoxin units/m3). NL from gain workers showed a higher concentration of total cells (55,000 +/- 14,000 vs 25,000 +/- 5,000 cells per milliliter; p=0.03), a higher concentration of squamous epithelial cells (17,029.0 +/- 4,177 .0 vs 7,103.7 +/- 1,479.8 cells per milliliter; p=0.03), and a higher concentration of neutrophils (40,058.0 +/- 12,803.2 vs 17,891.0 +/- 3,822.3 cells per milliliter; p=0.10) compared with postal workers. Importantly, these differences in NL cellularity between grain workers and postal workers were observed within the three strata of smokers. To further assess the importance of total cells, squamous epithelial cells, and neutrophils in the NL fluid of grain workers, we investigated the relationship between these cell concentrations and (1) measures of dust and endotoxin exposure during the work shift. (2) spirometric measures of airflow obtained immediately before the NL, and (3) work-related respiratory symptoms. The concentration of total cells, the concentration of squamous epithelial cells, or the concentration of neutrophils in the NL was not associated with ambient levels of dust or endotoxin, with baseline or cross-shift changes in lung function, or with work-related respiratory symptoms. These findings suggest that increased NL cellularity may be seen in workers exposed to high dust levels

Grains of Nonferrous and Noble Metals in Iron-Manganese Formations and Igneous Rocks of Submarine Elevations of the Sea of Japan

Science.gov (United States)

Kolesnik, O. N.; Astakhova, N. V.

2018-01-01

Iron-manganese formations and igneous rocks of submarine elevations in the Sea of Japan contain overlapping mineral phases (grains) with quite identical morphology, localization, and chemical composition. Most of the grains conform to oxides, intermetallic compounds, native elements, sulfides, and sulfates in terms of the set of nonferrous, noble, and certain other metals (Cu, Zn, Sn, Pb, Ni, Mo, Ag, Pd, and Pt). The main conclusion that postvolcanic hydrothermal fluids are the key sources of metals is based upon a comparison of the data of electron microprobe analysis of iron-manganese formations and igneous rocks dredged at the same submarine elevations in the Sea of Japan.

Grain Grading and Handling.

Science.gov (United States)

Rendleman, Matt; Legacy, James

This publication provides an introduction to grain grading and handling for adult students in vocational and technical education programs. Organized in five chapters, the booklet provides a brief overview of the jobs performed at a grain elevator and of the techniques used to grade grain. The first chapter introduces the grain industry and…

Concurrent grain boundary motion and grain rotation under an applied stress

International Nuclear Information System (INIS)

Gorkaya, Tatiana; Molodov, Konstantin D.; Molodov, Dmitri A.; Gottstein, Guenter

2011-01-01

Simultaneous shear coupling and grain rotation were observed experimentally during grain boundary migration in high-purity Al bicrystals subjected to an external mechanical stress at elevated temperatures. This behavior is interpreted in terms of the structure of the investigated planar 18.2 o non-tilt grain boundary with a 20 o twist component. For characterization of the grain rotation after annealing under stress the bicrystal surface topography across the boundary was measured by atomic force microscopy. The temperature dependence of the boundary migration rate was measured and the migration activation energy determined.

Carbohydrate and protein contents of grain dusts in relation to dust morphology.

Science.gov (United States)

Dashek, W V; Olenchock, S A; Mayfield, J E; Wirtz, G H; Wolz, D E; Young, C A

1986-01-01

Grain dusts contain a variety of materials which are potentially hazardous to the health of workers in the grain industry. Because the characterization of grain dusts is incomplete, we are defining the botanical, chemical, and microbial contents of several grain dusts collected from grain elevators in the Duluth-Superior regions of the U.S. Here, we report certain of the carbohydrate and protein contents of dusts in relation to dust morphology. Examination of the gross morphologies of the dusts revealed that, except for corn, each dust contained either husk or pericarp (seed coat in the case of flax) fragments in addition to respirable particles. When viewed with the light microscope, the fragments appeared as elongated, pointed structures. The possibility that certain of the fragments within corn, settled, and spring wheat were derived from cell walls was suggested by the detection of pentoses following colorimetric assay of neutralized 2 N trifluoroacetic acid hydrolyzates of these dusts. The presence of pentoses together with the occurrence of proteins within water washings of grain dusts suggests that glycoproteins may be present within the dusts. With scanning electron microscopy, each dust was found to consist of a distinct assortment of particles in addition to respirable particles. Small husk fragments and "trichome-like" objects were common to all but corn dust. Images FIGURE 4. FIGURE 5. PMID:3709476

Assessment of Workers' Exposure to Grain Dust and Bioaerosols During the Loading of Vessels' Hold: An Example at a Port in the Province of Québec.

Science.gov (United States)

Marchand, Geneviève; Gardette, Marie; Nguyen, Kiet; Amano, Valérie; Neesham-Grenon, Eve; Debia, Maximilien

2017-08-01

Longshoremen are exposed to large amounts of grain dust while loading of grain into the holds of vessels. Grain dust inhalation has been linked to respiratory diseases such as chronic bronchitis, hypersensitivity, pneumonitis, and toxic pneumonitis. Our objective was to characterize the exposure of longshoremen to inhalable and total dust, endotoxins, and cultivable bacteria and fungi during the loading of grain in a vessel's hold at the Port of Montreal in order to assess the potential health risks. Sampling campaigns were conducted during the loading of two different types of grain (wheat and corn). Environmental samples of microorganisms (bacteria, fungus, and actinomycetes) were taken near the top opening of the ship's holds while personal breathing zone measurements of dust and endotoxins were sampled during the worker's 5-hour shifts. Our study show that all measurements are above the recommendations with concentration going up to 390 mg m-3 of total dust, 89 mg m-3 of inhalable fraction, 550 000 EU m-3 of endotoxins, 20 000 CFU m-3 of bacteria, 61 000 CFU m-3 of fungus and 2500 CFU m-3 of actinomycetes. In conclusion, longshoremen are exposed to very high levels of dust and of microorganisms and their components during grain loading work. Protective equipment needs to be enforced for all workers during such tasks in order to reduce their exposure. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

The role of endotoxin in grain dust exposure and airway obstruction.

Science.gov (United States)

Von Essen, S

1997-05-01

Grain dust exposure is a common cause of respiratory symptoms in grain workers, feed mill employees, and farmers. Many of these workers develop wheezing and acute and chronic bronchitis symptoms, which can be associated with obstructive changes on pulmonary function testing. It has recently been demonstrated that grain dust exposure causes neutrophilic airways inflammation and systemic symptoms related to release of interleukin-1, tumor necrosis factor, interleukin-6, and other mediators of inflammation. Although grain dust is a heterogenous substance, endotoxin has received the greatest amount of attention as a possible cause of the airway inflammation that occurs after grain dust exposure. Although endotoxin undoubtedly causes a portion of the changes seen after grain dust exposure, it is becoming clear that other substances play a role as well.

Solution of problems of automation of elevator complex

Directory of Open Access Journals (Sweden)

V. S. Kudryashov

2018-01-01

Full Text Available The article is devoted to the solution of automation tasks in the development of the operator's workstation (AWP for controlling the elevator with a capacity of 280 tons per hour as part of the work of LLC "Intelligent Automation Complexes". In the existing elevator complexes, only grain transportation is provided (there are no control systems with automatic grain drying with high accuracy of humidity measurement, automatic generation of grain transportation routes is not provided (for each route, a technical task is required and changes to the control program of the system are required. At the same time, more precise regulation of the flow of grain flows is required (the automatic latches used have only the "open / close" positions. The goal of elevator automation is: to reduce the time of equipment downturn by tracking the operating time of the equipment, the number of accidents and informing the operator about equipment that is susceptible to failure; reduction of the time for setting up and servicing the elevator; improvement of product quality; a decrease in the percentage of rejects, as well as a decrease in the influence of the human factor on the process. The paper provides a brief description of the proposed gate valve control algorithms, the auto-building of the grain drying route, the filtering of the grain moisture readings and the fragments of the operator's workstation program (in indusoft web studio for controlling the elevator complex. The proposed solutions allow: to reduce the time of equipment downtime by 20% and the total service time of the complex; weed out the undried grain for ridding in automatic mode for repeated drying; to improve the quality of products through automatic control of grain overheating; to reduce the production waste by 3%, and also to reduce the influence of the human factor on the process of grain transportation and drying.

The proportion of nitrate in leaf nitrogen, but not changes in root growth, are associated with decreased grain protein in wheat under elevated [CO2].

Science.gov (United States)

Bahrami, Helale; De Kok, Luit J; Armstrong, Roger; Fitzgerald, Glenn J; Bourgault, Maryse; Henty, Samuel; Tausz, Michael; Tausz-Posch, Sabine

2017-09-01

The atmospheric CO 2 concentration ([CO 2 ]) is increasing and predicted to reach ∼550ppm by 2050. Increasing [CO 2 ] typically stimulates crop growth and yield, but decreases concentrations of nutrients, such as nitrogen ([N]), and therefore protein, in plant tissues and grains. Such changes in grain composition are expected to have negative implications for the nutritional and economic value of grains. This study addresses two mechanisms potentially accountable for the phenomenon of elevated [CO 2 ]-induced decreases in [N]: N uptake per unit length of roots as well as inhibition of the assimilation of nitrate (NO 3 - ) into protein are investigated and related to grain protein. We analysed two wheat cultivars from a similar genetic background but contrasting in agronomic features (Triticum aestivum L. cv. Scout and Yitpi). Plants were field-grown within the Australian Grains Free Air CO 2 Enrichment (AGFACE) facility under two atmospheric [CO 2 ] (ambient, ∼400ppm, and elevated, ∼550ppm) and two water treatments (rain-fed and well-watered). Aboveground dry weight (ADW) and root length (RL, captured by a mini-rhizotron root growth monitoring system), as well as [N] and NO 3 - concentrations ([NO 3 - ]) were monitored throughout the growing season and related to grain protein at harvest. RL generally increased under e[CO 2 ] and varied between water supply and cultivars. The ratio of total aboveground N (TN) taken up per RL was affected by CO 2 treatment only later in the season and there was no significant correlation between TN/RL and grain protein concentration across cultivars and [CO 2 ] treatments. In contrast, a greater percentage of N remained as unassimilated [NO 3 - ] in the tissue of e[CO 2 ] grown crops (expressed as the ratio of NO 3 - to total N) and this was significantly correlated with decreased grain protein. These findings suggest that e[CO 2 ] directly affects the nitrate assimilation capacity of wheat with direct negative implications

Snow Grain Size Retrieval over the Polar Ice Sheets with the Ice, Cloud and Land Elevation Satellite (ICESat) Observations

Science.gov (United States)

Yang, Yuekui; Marshak, Alexander; Han, Mei; Palm, Stephen P.; Harding, David J.

2016-01-01

Snow grain size is an important parameter for cryosphere studies. As a proof of concept, this paper presents an approach to retrieve this parameter over Greenland, East and West Antarctica ice sheets from surface reflectances observed with the Geoscience Laser Altimeter System (GLAS) onboard the Ice, Cloud, and land Elevation Satellite (ICESat) at 1064 nanometers. Spaceborne lidar observations overcome many of the disadvantages in passive remote sensing, including difficulties in cloud screening and low sun angle limitations; hence tend to provide more accurate and stable retrievals. Results from the GLAS L2A campaign, which began on 25 September and lasted until 19 November, 2003, show that the mode of the grain size distribution over Greenland is the largest (approximately 300 microns) among the three, West Antarctica is the second (220 microns) and East Antarctica is the smallest (190 microns). Snow grain sizes are larger over the coastal regions compared to inland the ice sheets. These results are consistent with previous studies. Applying the broadband snow surface albedo parameterization scheme developed by Garder and Sharp (2010) to the retrieved snow grain size, ice sheet surface albedo is also derived. In the future, more accurate retrievals can be achieved with multiple wavelengths lidar observations.

Aspergillus candidus: a respiratory hazard associated with grain dust.

Science.gov (United States)

Krysinska-Traczyk, E; Dutkiewicz, J

2000-01-01

The concentration of Aspergillus candidus in samples of grain dust and of air polluted with grain dust was found to be large (respectively 3.0 x 10(5) - 3.0 x 10(9) cfu/g and 5.0 x 10(3) - 6.47 x 10(5) cfu/m(3)) and proved to be significantly greater compared to samples of other organic dusts (pgrain workers reacted significantly more frequently to extract of A. candidus in the leukocyte migration inhibition test (pdusts. It was concluded that Aspergillus candidus, because of its common occurrence and strong immunomodulating properties, poses an important occupational hazard for grain handling workers

Mortality among retired fur workers. Dyers, dressers (tanners) and service workers

Energy Technology Data Exchange (ETDEWEB)

Sweeney, M.H.; Walrath, J.; Waxweiler, R.J.

1985-08-01

A retrospective cohort mortality study was conducted on 807 fur dyers, fur dressers (tanners), and fur service workers who were pensioned between 1952 and 1977 by the Fur, Leather and Machine Workers Union of New York City. Workplace exposures of fur workers varied with job category. Dyers were exposed to oxidative dyes used in commercial hair dyes; dressers and service workers were exposed to tanning chemicals. In a comparison with the New York City population, no significant increases in mortality were observed among the fur dyers. Among fur dressers, mortality from all malignant neoplasms and lung cancer was significantly elevated, as was mortality from cardiovascular disease among fur service workers. When examined by ethnic origin, the elevated SMR values and directly age-adjusted rate ratios suggested that foreign-born fur dressers and eastern European-born fur workers experienced the highest risks for lung and colorectal cancers, respectively. These data support previous findings of increased mortality from colorectal cancer in the foreign-born population of the United States and suggest a possible occupational etiology for the observed lung cancer excess.

Achievable space elevators for space transportation and starship acceleration

Science.gov (United States)

Pearson, Jerome

1990-04-01

Space elevator concepts for low-cost space launches are reviewed. Previous concepts suffered from requirements for ultra-high-strength materials, dynamically unstable systems, or from danger of collision with space debris. The use of magnetic grain streams solves these problems. Magnetic grain streams can support short space elevators for lifting payloads cheaply into Earth orbit, overcoming the material strength problem in building space elevators. Alternatively, the stream could support an international spaceport circling the Earth daily tens of miles above the equator, accessible to advanced aircraft. Mars could be equipped with a similar grain stream, using material from its moons Phobos and Deimos. Grain-stream arcs about the sun could be used for fast launches to the outer planets and for accelerating starships to near lightspeed for interstellar reconnaisance. Grain streams are essentially impervious to collisions, and could reduce the cost of space transportation by an order of magnitude.

Composition of extracts of airborne grain dusts: lectins and lymphocyte mitogens.

Science.gov (United States)

Olenchock, S A; Lewis, D M; Mull, J C

1986-01-01

Airborne grain dusts are heterogeneous materials that can elicit acute and chronic respiratory pathophysiology in exposed workers. Previous characterizations of the dusts include the identification of viable microbial contaminants, mycotoxins, and endotoxins. We provide information on the lectin-like activity of grain dust extracts and its possible biological relationship. Hemagglutination of erythrocytes and immunochemical modulation by antibody to specific lectins showed the presence of these substances in extracts of airborne dusts from barley, corn, and rye. Proliferation of normal rat splenic lymphocytes in vitro provided evidence for direct biological effects on the cells of the immune system. These data expand the knowledge of the composition of grain dusts (extracts), and suggest possible mechanisms that may contribute to respiratory disease in grain workers. PMID:3709474

Mortality among retired fur workers. Dyers, dressers (tanners) and service workers.

Science.gov (United States)

Sweeney, M H; Walrath, J; Waxweiler, R J

1985-08-01

A retrospective cohort mortality study was conducted on 807 fur dyers, fur dressers (tanners), and fur service workers who were pensioned between 1952 and 1977 by the Fur, Leather and Machine Workers Union of New York City. Workplace exposures of fur workers varied with job category. Dyers were exposed to oxidative dyes used in commercial hair dyes; dressers and service workers were exposed to tanning chemicals. In a comparison with the New York City population, no significant increases in mortality were observed among the fur dyers. Among fur dressers, mortality from all malignant neoplasms [standardized mortality ratio (SMR) 151] and lung cancer (SMR 232) was significantly elevated, as was mortality from cardiovascular disease (SMR 126) among fur service workers. When examined by ethnic origin, the elevated SMR values and directly age-adjusted rate ratios suggested that foreign-born fur dressers and eastern European-born fur workers experienced the highest risks for lung and colorectal cancers, respectively. These data support previous findings of increased mortality from colorectal cancer in the foreign-born population of the United States and suggest a possible occupational etiology for the observed lung cancer excess.

Regional elevator survey : grain transportation & industry trends for Great Plains elevators

Science.gov (United States)

2001-08-01

One potential means for gaining insight into the current state of the elevator industry, : and into expectations for future trends, is through a survey. The objective of this study is to profile the transportation and industry characteristics of the ...

Effects of polymorphic variations in tumor necrosis factor alpha and occupational exposure to grain dust on longitudinal decline in pulmonary function.

Science.gov (United States)

Pahwa, Punam; Nakagawa, Kazuko; Koehncke, Niels; McDuffie, Helen H

2009-01-01

Longitudinal declines in pulmonary function are associated with individuals experiencing occupational exposure to organic dusts in combination with lifestyle factors such as cigarette smoking and with genetic factors, and interactions between these factors. To investigate the relationship between polymorphism of genes encoding Tumor Necrosis Factor Alpha (TNF-alpha) and longitudinal lung function decline in grain workers exposed to grain dust. Male grain handlers who participated in the Saskatchewan Grain Workers Surveillance Program from 2002 through 2005 provided demographic, occupational, lifestyle, and respiratory symptoms information as well as pulmonary function measurements and DNA for genotyping. Marginal models using the generalized estimating equations approach were fitted by using a SAS PROC GENMOD to predict the annual decline in Forced Expired Volume in one second (FEV(1)) and Forced Vital Capacity (FVC). Smoking intensity contributed to the decline in FEV(1.)Among *1/*1 homozygotes and *1/*2 heterozygotes, grain workers with grain industry had significantly lower FEV(1)declines compared to those of the other two exposure groups (>10 and 20 years in the grain industry). The annual declines in FEV(1)for grain workers who were either *1/*1 homozygote or *1/*2 heterozygote and had been in the grain industry for grain workers who were *2/*2 genotype and had been in the industry for grain industry is an effect modifier between TNF-alpha 308 genotype and longitudinal decline in FEV(1)in male subjects exposed to grain dust.

A Rare Allele of GS2 Enhances Grain Size and Grain Yield in Rice.

Science.gov (United States)

Hu, Jiang; Wang, Yuexing; Fang, Yunxia; Zeng, Longjun; Xu, Jie; Yu, Haiping; Shi, Zhenyuan; Pan, Jiangjie; Zhang, Dong; Kang, Shujing; Zhu, Li; Dong, Guojun; Guo, Longbiao; Zeng, Dali; Zhang, Guangheng; Xie, Lihong; Xiong, Guosheng; Li, Jiayang; Qian, Qian

2015-10-05

Grain size determines grain weight and affects grain quality. Several major quantitative trait loci (QTLs) regulating grain size have been cloned; however, our understanding of the underlying mechanism that regulates the size of rice grains remains fragmentary. Here, we report the cloning and characterization of a dominant QTL, grain size on chromosome 2 (GS2), which encodes Growth-Regulating Factor 4 (OsGRF4), a transcriptional regulator. GS2 localizes to the nucleus and may act as a transcription activator. A rare mutation of GS2 affecting the binding site of a microRNA, OsmiR396c, causes elevated expression of GS2/OsGRF4. The increase in GS2 expression leads to larger cells and increased numbers of cells, which thus enhances grain weight and yield. The introduction of this rare allele of GS2/OsGRF4 into rice cultivars could significantly enhance grain weight and increase grain yield, with possible applications in breeding high-yield rice varieties. Copyright © 2015 The Author. Published by Elsevier Inc. All rights reserved.

Elevated CO2 Reduced Floret Death in Wheat Under Warmer Average Temperatures and Terminal Drought

Science.gov (United States)

Dias de Oliveira, Eduardo; Palta, Jairo A.; Bramley, Helen; Stefanova, Katia; Siddique, Kadambot H. M.

2015-01-01

Elevated CO2 often increases grain yield in wheat by enhancing grain number per ear, which can result from an increase in the potential number of florets or a reduction in the death of developed florets. The hypotheses that elevated CO2 reduces floret death rather than increases floret development, and that grain size in a genotype with more grains per unit area is limited by the rate of grain filling, were tested in a pair of sister lines contrasting in tillering capacity (restricted- vs. free-tillering). The hypotheses were tested under elevated CO2, combined with +3°C above ambient temperature and terminal drought, using specialized field tunnel houses. Elevated CO2 increased net leaf photosynthetic rates and likely the availability of carbon assimilates, which significantly reduced the rates of floret death and increased the potential number of grains at anthesis in both sister lines by an average of 42%. The restricted-tillering line had faster grain-filling rates than the free-tillering line because the free-tillering line had more grains to fill. Furthermore, grain-filling rates were faster under elevated CO2 and +3°C above ambient. Terminal drought reduced grain yield in both lines by 19%. Elevated CO2 alone increased the potential number of grains, but a trade-off in yield components limited grain yield in the free-tillering line. This emphasizes the need for breeding cultivars with a greater potential number of florets, since this was not affected by the predicted future climate variables. PMID:26635837

Elevated CO2 reduced floret death in wheat under warmer average temperatures and terminal drought.

Directory of Open Access Journals (Sweden)

Eduardo eDias de Oliveira

2015-11-01

Full Text Available Elevated CO2 often increases grain yield in wheat by enhancing grain number per ear, which can result from an increase in the potential number of florets or a reduction in the death of developed florets. The hypotheses that elevated CO2 reduces floret death rather than increases floret development, and that grain size in a genotype with more grains per unit area is limited by the rate of grain filling, were tested in a pair of sister lines contrasting in tillering capacity (restricted- vs free-tillering. The hypotheses were tested under elevated CO2, combined with +3 C above ambient temperature and terminal drought, using specialized field tunnel houses. Elevated CO2 increased net leaf photosynthetic rates and likely the availability of carbon assimilates, which significantly reduced the rates of floret death and increased the potential number of grains at anthesis in both sister lines by an average of 42%. The restricted-tillering line had faster grain-filling rates than the free-tillering line because the free-tillering line had more grains to fill. Furthermore, grain-filling rates were faster under elevated CO2 and +3 C above ambient. Terminal drought reduced grain yield in both lines by 19%. Elevated CO2 alone increased the potential number of grains, but a trade-off in yield components limited grain yield in the free-tillering line. This emphasizes the need for breeding cultivars with a greater potential number of florets, since this was not affected by the predicted future climate variables.

Industrial application of radiation disinfestation of grain

International Nuclear Information System (INIS)

Zakladnoj, G.A.; Men'shenin, A.I.; Pertsovskij, E.S.; Salimov, R.A.; Cherepkov, V.G.; Krsheminskij, V.S.

1982-01-01

One of the main reasons for grain losses during storage is its damage by pest insects. Chemical methods widely used at present for grain decontamination have some shortcomings. In this connection a radiation method for grain disinfestation is developed and introduced in industry. First in the world experimental-industrial disinfestator on the base of electron accelerators is put into operation at Odessa port elevator

Elevated urinary levels of kidney injury molecule-1 among Chinese factory workers exposed to trichloroethylene

Science.gov (United States)

Vermeulen, Roel; Huang, Hanlin; Rothman, Nathaniel; Lan, Qing

2012-01-01

Epidemiological studies suggest that trichloroethylene (TCE) exposure may be associated with renal cancer. The biological mechanisms involved are not exactly known although nephrotoxicity is believed to play a role. Studies on TCE nephrotoxicity among humans, however, have been largely inconsistent. We studied kidney toxicity in Chinese factory workers exposed to TCE using novel sensitive nephrotoxicity markers. Eighty healthy workers exposed to TCE and 45 comparable unexposed controls were included in the present analyses. Personal TCE exposure measurements were taken over a 2-week period before urine collection. Ninety-six percent of workers were exposed to TCE below the current US Occupational Safety and Health Administration permissible exposure limit (100 ppm 8h TWA), with a mean (SD) of 22.2 (35.9) ppm. Kidney injury molecule-1 (KIM-1) and Pi-glutathione S transferase (GST) alpha were elevated among the exposed subjects as compared with the unexposed controls with a strong exposure-response association between individual estimates of TCE exposure and KIM-1 (P < 0.0001). This is the first report to use a set of sensitive nephrotoxicity markers to study the possible effects of TCE on the kidneys. The findings suggest that at relatively low occupational exposure levels a toxic effect on the kidneys can be observed. This finding supports the biological plausibility of linking TCE exposure and renal cancer. Abbreviations:GSTglutathione-S-transferaseKIM-1kidney injury molecule-1NAGN-acetyl-beta-(d)-glucosaminidaseOVMorganic vapour monitoringTCEtrichloroethyleneVEGFvascular endothelial growth factor. PMID:22665366

Elevated oxidative damage in kitchen workers in Chinese restaurants.

Science.gov (United States)

Wang, Jiajia; Luo, Xiaolin; Xu, Bin; Wei, Jun; Zhang, Zhenzhen; Zhu, Huilian

2011-01-01

To investigate associations between occupational exposure to cooking oil fumes (COFs) and potential oxidative and genotoxic effects in kitchen workers. Sixty-seven male kitchen workers and 43 male controls from Chinese restaurants in Guangzhou were recruited. For all the participants, the levels of 1-hydroxypyrene (1-OHP) and 8-hydroxy-2-deoxyguanosine (8-oxodG) in urine, binucleated micronucleus (BNMN) frequency, comet tail length and tail DNA% in peripheral blood lymphocytes (PBLs) and malondialdehyde (MDA) and superoxide dismutase (SOD) in serum were measured. The inhalable particulates (PM(10)) in their workplaces were also monitored. Our results showed that the exposed group had a significantly higher median level of urinary 1-OHP than that of the control group (pkitchen and cooking time per day. All these positive associations remained after adjusting for the four confounders in a subsequent multivariate linear regression analysis. Occupational exposure to COFs led to increased oxidative damage in Chinese kitchen workers. The health consequences of these oxidative changes need further investgation. Urinary 1-OHP and 8-oxodG are noninvasive and effective biomarkers for assessment of oxidative damage in restaurants workers.

Concepts on Low Temperature Mechanical Grain Growth

Energy Technology Data Exchange (ETDEWEB)

Sharon, John Anthony [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Metallurgy and Materials Joining Dept.; Boyce, Brad Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Metallurgy and Materials Joining Dept.

2013-11-01

In metals, as grain size is reduced below 100nm, conventional dislocation plasticity is suppressed resulting in improvements in strength, hardness, and wears resistance. Existing and emerging components use fine grained metals for these beneficial attributes. However, these benefits can be lost in service if the grains undergo growth during the component’s lifespan. While grain growth is traditionally viewed as a purely thermal process that requires elevated temperature exposure, recent evidence shows that some metals, especially those with nanocrystalline grain structure, can undergo grain growth even at room temperature or below due to mechanical loading. This report has been assembled to survey the key concepts regarding how mechanical loads can drive grain coarsening at room temperature and below. Topics outlined include the atomic level mechanisms that facilitate grain growth, grain boundary mobility, and the impact of boundary structure, loading scheme, and temperature.

Diagnosis and management of grain-induced asthma.

Science.gov (United States)

Quirce, Santiago; Diaz-Perales, Araceli

2013-11-01

Grain-induced asthma is a frequent occupational allergic disease mainly caused by inhalation of cereal flour or powder. The main professions affected are bakers, confectioners, pastry factory workers, millers, farmers, and cereal handlers. This disorder is usually due to an IgE-mediated allergic response to inhalation of cereal flour proteins. The major causative allergens of grain-related asthma are proteins derived from wheat, rye and barley flour, although baking additives, such as fungal α-amylase are also important. This review deals with the current diagnosis and treatment of grain-induced asthma, emphasizing the role of cereal allergens as molecular tools to enhance diagnosis and management of this disorder. Asthma-like symptoms caused by endotoxin exposure among grain workers are beyond the scope of this review. Progress is being made in the characterization of grain and bakery allergens, particularly cereal-derived allergens, as well as in the standardization of allergy tests. Salt-soluble proteins (albumins plus globulins), particularly members of the α-amylase/trypsin inhibitor family, thioredoxins, peroxidase, lipid transfer protein and other soluble enzymes show the strongest IgE reactivities in wheat flour. In addition, prolamins (not extractable by salt solutions) have also been claimed as potential allergens. However, the large variability of IgE-binding patterns of cereal proteins among patients with grain-induced asthma, together with the great differences in the concentrations of potential allergens observed in commercial cereal extracts used for diagnosis, highlight the necessity to standardize and improve the diagnostic tools. Removal from exposure to the offending agents is the cornerstone of the management of grain-induced asthma. The availability of purified allergens should be very helpful for a more refined diagnosis, and new immunomodulatory treatments, including allergen immunotherapy and biological drugs, should aid in the management

Study of nanophase TiO2 grain boundaries by Raman spectroscopy

International Nuclear Information System (INIS)

Melendres, C.A.; Narayanasamy, A.; Maroni, V.A.; Siegel, R.W.

1989-01-01

Raman spectra have been recorded for as-consolidated nanophase TiO 2 samples with differing grain sizes and on samples annealed in air at a variety of temperatures up to 1273 K. The nanophase samples with the smallest grain size, about 12 nm average diameter, could have 15-30% of their atoms in grain boundaries; nevertheless, the strong Raman-active lines representative of the rutile structure were found to dominate all of the observed spectra, independent of grain size and annealing treatment. These lines were quite broad in the as-consolidated nanophase samples, equally in 12 nm and 100 nm grain-size compacts, but sharpened considerably upon annealing at elevated temperatures. The Raman data give no indication of grain-boundary structures in nanophase TiO 2 that are significantly different from those in conventional polycrystals. However, defect structures within the grains, which anneal out at elevated temperatures, are evidenced by changes in the Raman spectra. 15 refs., 2 figs

Recommendations for reducing the effect of grain dust on the lungs. Canadian Thoracic Society Standards Committee.

Science.gov (United States)

Becklake, M; Broder, I; Chan-Yeung, M; Dosman, J A; Ernst, P; Herbert, F A; Kennedy, S M; Warren, P W

1996-11-15

To assess the appropriateness of the current Canadian standards for exposure to grain dust in the workplace. The current permissible exposure limit of 10 mg of total grain dust per cubic metre of air (expressed as mg/m3) as an 8-hour time-weighted average exposure, or a lower permissible exposure limit. Acute symptoms of grain-dust exposure, such as cough, phlegm production, wheezing and dyspnea, similar chronic symptoms, and spirometric deficits revealing obstructive or restrictive disease. Articles published from 1924 to December 1993 were identified from Index Medicus and the bibliographies of pertinent articles. Subsequent articles published from 1994 (when the recommendations were approved by the Canadian Thoracic Society Standards Committee) to June 1996 were retrieved through a search of MEDLINE, and modification of the recommendations was not found to be necessary. Studies of interest were those that linked measurements of total grain dust levels to the development of acute and chronic respiratory symptoms and changes in lung function in exposed workers. Papers on the effects of grain dust on workers in feed mills were not included because other nutrients such as animal products may have been added to the grain. Unpublished reports (e.g., to Labour Canada) were included as sources of information. A high value was placed on minimizing the biological harm that grain dust has on the lungs of grain workers. A permissible exposure limit of 5 mg/m3 would control the short-term effects of exposure to grain dust on workers. Evidence is insufficient to determine what level is needed to prevent long-term effects. The economic implications of implementing a lower permissible exposure limit have not been evaluated. The current Canadian standards for grain-dust exposure should be reviewed by Labour Canada and the grain industry. A permissible exposure level of 5 mg/m3 is recommended to control short-term effects. Further measurements that link the levels of exposure to

76 FR 32988 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Grain...

Science.gov (United States)

2011-06-07

... for OMB Review; Comment Request; Grain Handling Facilities ACTION: Notice. SUMMARY: The Department of... collection request (ICR) titled, ``Grain Handling Facilities (29 CFR 1910.272),'' to the Office of Management... directed toward assuring the safety of workers in grain handling through development of a housekeeping plan...

Computer-aided analysis of grain growth in metals

DEFF Research Database (Denmark)

Klimanek, P.; May, C.; Richter, H.

1993-01-01

Isothermal grain growth in aluminium, copper and alpha-iron was investigated experimentally at elevated temperatures and quantitatively interpreted by computer simulation on the base of a statistical model described in [4,5,6]. As it is demonstrated for the grain growth kinetics, the experimental...... data can be fitted satisfactorly....

The Relationship Between Microscopic Grain Surface Structure and the Dynamic Capillary-Driven Advance of Water Films over Individual Dry Natural Sand Grains

Science.gov (United States)

Kibbey, T. C. G.; Adegbule, A.; Yan, S.

2017-12-01

The movement of nonvolatile solutes in unsaturated porous media at low water contents depends on transport in surface-associated water films. The focus of the work described here was on studying solute movement in water films advancing by capillary forces over initially-dry grain surfaces, to understand how microscopic surface roughness features influence the initial velocity of water film advance. For this work, water containing a non-adsorbing conservative tracer was used to track the movement of advancing water films. A stainless steel capillary tube connected to an external reservoir a fixed distance below the grain surface was used to transmit solution to the grain surface under negative pressure (positive capillary pressure), consistent with conditions that might be expected in the unsaturated zone. The small internal diameter of the capillary prevents solution from draining out of the capillary back into the reservoir. When the capillary is contacted with a grain surface, capillary forces that result from contact between the fluid and the rough grain surface cause water films to wick across the grain surface. Multiple experiments were conducted on the same grain, rotating the grain and varying the capillary contact point around the circumference of the grain. Imaging was conducted at fixed intervals using an automated Extended Depth of Field (EDF) imaging system, and images were analyzed to determine initial velocity. Grain surfaces were then characterized through scanning electron microscope (SEM) imaging, using a hybrid stereoscopic reconstruction method designed to extract maximum detail in creating elevation maps of geologic surfaces from tilted pairs of SEM images. The resulting elevation maps were used to relate surface roughness profiles around the grain with initial velocities. Results suggest that velocity varies significant with contact point around an individual grain, and correlates quantitatively with the local grain surface structure

Presence of specific IgG antibody to grain dust does not go with respiratory symptoms.

Science.gov (United States)

Park, H S; Suh, C H; Nahm, D H; Kim, H Y

1999-02-01

A high prevalence of work-related symptoms in relation to grain dust exposure has been reported in grain dust workers, but the role of the specific IgG antibody is unknown. To study the possible role of specific IgG (sIgG) and specific IgG4 (sIgG4) in the development of work-related symptoms, sIgG and sIgG4 subclass antibodies against grain dust antigens were determined by ELISA in sera from 43 workers and 27 non-exposed controls. They were compared with results of specific IgE antibodies, exposure intensity and the presence of respiratory symptoms. SIgG and sIgG4 antibodies were detectable in almost all sera of exposed workers, and the prevalence were significantly higher than those of controls (pgrain dust exposure and may unlikely play a role in the etiology of respiratory symptoms.

Elevated temperature mechanical properties of novel ultra-fine grained Cu–Nb composites

Energy Technology Data Exchange (ETDEWEB)

Primorac, Mladen-Mateo [Department of Materials Physics, Montanuniversität Leoben (Austria); Abad, Manuel David; Hosemann, Peter [Department of Nuclear Engineering, University of California, Berkeley (United States); Kreuzeder, Marius [Department of Materials Physics, Montanuniversität Leoben (Austria); Maier, Verena [Department of Materials Physics, Montanuniversität Leoben (Austria); Erich-Schmid Institute for Materials Science, Austrian Academy of Sciences, Leoben (Austria); Kiener, Daniel, E-mail: daniel.kiener@unileoben.ac.at [Department of Materials Physics, Montanuniversität Leoben (Austria)

2015-02-11

Ultra-fine grained materials exhibit outstanding properties and are therefore favorable for prospective applications. One of these promising systems is the composite assembled by the body centered cubic niobium and the face centered cubic copper. Cu–Nb composites show a high hardness and good thermal stability, as well as a high radiation damage tolerance. These properties make the material interesting for use in nuclear reactors. The aim of this work was to create a polycrystalline ultra-fine grained composite for high temperature applications. The samples were manufactured via a powder metallurgical route using high pressure torsion, exhibiting a randomly distributed oriented grain size between 100 and 200 nm. The mechanical properties and the governing plastic deformation behavior as a function of temperature were determined by high temperature nanoindentation up to 500 °C. It was found that in the lower temperature regions up to 300 °C the plastic deformation is mainly governed by dislocation interactions, such as dislocation glide and the nucleation of kink pairs. For higher temperatures, thermally activated processes at grain boundaries are proposed to be the main mechanism governing plastic deformation. This mechanistic view is supported by temperature dependent changes in hardness, strain rate sensitivity, activation volume, and activation energy.

Effects of exposure to flour dust on respiratory symptoms and pulmonary function of mill workers

Directory of Open Access Journals (Sweden)

Hamdy A. Mohammadien

2013-10-01

Conclusion: Flour mill workers in Sohag Governorate, like grain workers elsewhere, were at an increased risk of developing pulmonary symptoms, a strong association exists between exposure to flour dust and the prevalence of respiratory symptoms and functional impairments of the lungs. The result has implications for improved dust control measures in the grain industry in Egypt.

Economic Analysis for Commingling Effects of Insect Activity in the Elevator Boot Area.

Science.gov (United States)

Tilley, Dennis R; Casada, Mark E; Langemeier, Michael R; Subramanyam, Bhadriraju; Arthur, Frank H

2015-12-01

Boot areas in commercial grain elevators and feed mills contribute to commingling of insects with grain that moves through the elevator leg. A partial budget and stochastic dominance model were developed to improve pest management decision-making and risk analysis assessment from commingling effects of insect activity in the boot area. Modified pilot-scale bucket elevator legs, containing residual wheat or corn, were infested with varying insect pest densities prior to clean grain transfers. Appropriate grain discounts were applied to grain samples obtained from clean grain transfers over either: 1) insect-free and untreated boots, 2) infested and untreated boots, or 3) infested and chemical-treated (β-cyfluthrin) boots. The insect-free boots simulated performing clean-out of the boot area. Partial budget analysis and stochastic dominance modeling indicated that boot sanitation (cleanout) about every 30 d, avoiding costly grain discounts from insect commingling, is the preferred choice. Although chemical spray treatments of the empty boot may reduce insect populations of some boot residual grains, boot cleanout always had lower and usually zero insect pest populations in the boot residual grain, providing higher facility operational net income without the use of chemicals. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by US Government employees and is in the public domain in the US.

Rising atmospheric CO2 concentration may imply higher risk of Fusarium mycotoxin contamination of wheat grains.

Science.gov (United States)

Bencze, Szilvia; Puskás, Katalin; Vida, Gyula; Karsai, Ildikó; Balla, Krisztina; Komáromi, Judit; Veisz, Ottó

2017-08-01

Increasing atmospheric CO 2 concentration not only has a direct impact on plants but also affects plant-pathogen interactions. Due to economic and health-related problems, special concern was given thus in the present work to the effect of elevated CO 2 (750 μmol mol -1 ) level on the Fusarium culmorum infection and mycotoxin contamination of wheat. Despite the fact that disease severity was found to be not or little affected by elevated CO 2 in most varieties, as the spread of Fusarium increased only in one variety, spike grain number and/or grain weight decreased significantly at elevated CO 2 in all the varieties, indicating that Fusarium infection generally had a more dramatic impact on the grain yield at elevated CO 2 than at the ambient level. Likewise, grain deoxynivalenol (DON) content was usually considerably higher at elevated CO 2 than at the ambient level in the single-floret inoculation treatment, suggesting that the toxin content is not in direct relation to the level of Fusarium infection. In the whole-spike inoculation, DON production did not change, decreased or increased depending on the variety × experiment interaction. Cooler (18 °C) conditions delayed rachis penetration while 20 °C maximum temperature caused striking increases in the mycotoxin contents, resulting in extremely high DON values and also in a dramatic triggering of the grain zearalenone contamination at elevated CO 2 . The results indicate that future environmental conditions, such as rising CO 2 levels, may increase the threat of grain mycotoxin contamination.

Telephone Crisis Support Workers' Psychological Distress and Impairment.

Science.gov (United States)

Kitchingman, Taneile A; Wilson, Coralie J; Caputi, Peter; Wilson, Ian; Woodward, Alan

2018-01-01

In order to respond to crises with appropriate intervention, crisis workers are required to manage their own needs as well as the needs of those they respond to. A systematic review of the literature was conducted to examine whether telephone crisis support workers experience elevated symptoms of psychological distress and are impaired by elevated symptoms. Studies were identified in April 2015 by searching three databases, conducting a gray literature search, and forward and backward citation chaining. Of 113 identified studies, seven were included in the review. Results suggest that that telephone crisis support workers experience symptoms of vicarious traumatization, stress, burnout, and psychiatric disorders, and that they may not respond optimally to callers when experiencing elevated symptoms of distress. However, definitive conclusions cannot be drawn due to the paucity and methodological limitations of available data. While the most comprehensive search strategy possible was adopted, resource constraints meant that conference abstracts were not searched and authors were not contacted for additional unpublished information. There is an urgent need to identify the impact of telephone crisis support workers' role on their well-being, the determinants of worker well-being in the telephone crisis support context, and the extent to which well-being impacts their performance and caller outcomes. This will help inform strategies to optimize telephone crisis support workers' well-being and their delivery of support to callers.

[Contact dermatitis caused by acrylates among 8 workers in an elevator factory].

Science.gov (United States)

Pérez-Formoso, J L; de Anca-Fernández, J; Maraví-Cecilia, R; Díaz-Torres, J M

2010-05-01

Acrylates are widely used low-molecular-weight substances, initially introduced in industry in the 1930s and subsequently applied also in medicine and the home. One of their main features is the ability to undergo polymerization. The most commonly used acrylic compounds are cyanoacrylates, methacrylates, and acrylates. To confirm suspicion of occupational disease in a group of workers in an elevator factory. We studied 8 patients with dermatitis of the hands and finger pads. In their work, the patients came into contact with acrylates. Patch testing was applied with an acrylate panel (BIAL-Aristegui, Bilbao, Spain). Seven of the patients (87. 5%) had a positive result with 1% ethylene glycol dimethacrylate. Positive were also observed for 2% hydroxyethyl methacrylate (5 patients, 62. 5%), 1% triethylene glycol dimethacrylate (4 patients, 50%), 10% ethyl methacrylate monomer (3 patients, 37. 5%), 10% methyl methacrylate monomer (2 patients, 25%), 1% ethyl acrylate (1 patient, 12. 5%), and 0. 1% acrylic acid (1 patient, 12. 5%). We highlight the strong sensitizing capacity of acrylates and the importance of taking all necessary preventive measures in industries where these substances are used. Such measures should include avoidance of contact with the product in cases where sensitization has been confirmed.

7 CFR 800.25 - Required elevator and merchandising records.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Required elevator and merchandising records. 800.25 Section 800.25 Agriculture Regulations of the Department of Agriculture (Continued) GRAIN INSPECTION... REGULATIONS Recordkeeping and Access to Facilities § 800.25 Required elevator and merchandising records. (a...

Longitudinal association of obesity, metabolic syndrome and diabetes with risk of elevated aminotransferase levels in a cohort of Mexican health workers.

Science.gov (United States)

Flores, Yvonne N; Auslander, Allyn; Crespi, Catherine M; Rodriguez, Michael; Zhang, Zuo-Feng; Durazo, Francisco; Salmerón, Jorge

2016-05-01

In Mexico, chronic liver disease have been increasingly found along with the rapidly growing prevalence of obesity, diabetes and metabolic syndrome (MS). We aimed to investigate the longitudinal association between these three factors and risk of elevated alanine aminotransferase (ALT) levels (>40 U/L), a marker for liver damage, in a cohort of Mexican adults. Data were obtained from two separate waves of the Mexican Health Worker Cohort Study: Wave 1 (2004-2006) and Wave 2 (2011-2013). Unconditional logistic regression models were employed to determine the cross-sectional and longitudinal association between these risk factors and elevated ALT levels. The prevalence of elevated ALT was significantly higher among men, individuals aged under 60 years, those who were overweight or obese, diabetic, with MS or heavy/binge drinkers. The longitudinal results indicated that weight gain between waves that resulted in a change in body mass index, along with remaining overweight or obese, were significantly associated with an increased risk of elevated ALT levels. A significantly increased risk of developing elevated ALT was also observed among those who acquired diabetes or MS from Wave 1 to Wave 2. Weight gain and acquiring diabetes or MS are associated with a significant risk of having elevated ALT. These results, within the context of the rapid increase in global obesity rates, call urgently for programs to help to prevent chronic liver disease. © 2016 Chinese Medical Association Shanghai Branch, Chinese Society of Gastroenterology, Renji Hospital Affiliated to Shanghai Jiaotong University School of Medicine and John Wiley & Sons Australia, Ltd.

Cross-shift changes in blood inflammatory markers occur in the absence of airway obstruction in workers exposed to grain dust.

Science.gov (United States)

Borm, P J; Schins, R P; Derhaag, T J; Kant, I; Jorna, T H

1996-04-01

Grain dust is well known to cause both acute and chronic respiratory disorders, and endotoxins are considered key components in this. Since endotoxins are known to elicit proinflammatory mediators, we investigated cytokine (tumor necrosis factor [TNF], interleukin-6, interleukin-8) release and a number of proinflammatory and anti-inflammatory proteins (soluble TNF receptors, lipopolysaccharide (LPS) binding protein, bactericidal permeability increasing protein (BPI), C-reactive protein) in plasma of workers exposed to grain dust. In two surveys during 1 week, lung function was measured daily before and after the shift, using flow-volume curves and/or forced oscillation measurements. On Monday and Friday, blood samples (30 mL) were drawn and cytokine release was determined by enzyme-linked immunosorbent assay in supernatant of isolated monocytes or whole blood culture, either unstimulated or on the ex vivo stimulation with 3 ng/mL or 1,000 ng/mL endotoxin. Individual exposures were determined from stationary dust measurements at every workplace combined with personal task analysis during all shifts. In both surveys, no cross-week change in lung function parameters was observed. In the first survey (average exposure: 20.2 mg/m3), monocyte spontaneous TNF release was increased sevenfold cross week (pdust exposure (r=0.62) of that week and the increase in soluble TNF receptor 75 kD (r=0.85). In the second survey, where average exposure was much lower (3.67 mg/m3), impedance parameters indicated a significant improvement of airway function, and cross-week changes in inflammatory markers were minimal. Therefore, we conclude that inflammatory events can be used to monitor adverse respiratory effects of moderate grain dust exposure.

Grain boundary motion and grain rotation in aluminum bicrystals: recent experiments and simulations

International Nuclear Information System (INIS)

Molodov, D A; Barrales-Mora, L A; Brandenburg, J-E

2015-01-01

The results of experimental and computational efforts over recent years to study the motion of geometrically different grain boundaries and grain rotation under various driving forces are briefly reviewed. Novel in-situ measuring techniques based on orientation contrast imaging and applied simulation techniques are described. The experimental results obtained on specially grown aluminum bicrystals are presented and discussed. Particularly, the faceting and migration behavior of low angle grain boundaries under the curvature force is addressed. In contrast to the pure tilt boundaries, which remained flat/faceted and immobile during annealing at elevated temperatures, mixed tilt-twist boundaries readily assumed a curved shape and steadily moved under the capillary force. Computational analysis revealed that this behavior is due to the inclinational anisotropy of grain boundary energy, which in turn depends on boundary geometry. The shape evolution and shrinkage kinetics of cylindrical grains with different tilt and mixed boundaries were studied by molecular dynamics simulations. The mobility of low angle <100> boundaries with misorientation angles higher than 10°, obtained by both the experiments and simulations, was found not to differ from that of the high angle boundaries, but decreases essentially with further decrease of misorientation. The shape evolution of the embedded grains in simulations was found to relate directly to results of the energy computations. Further simulation results revealed that the shrinkage of grains with pure tilt boundaries is accompanied by grain rotation. In contrast, grains with the tilt-twist boundaries composed of dislocations with the mixed edge-screw character do not rotate during their shrinkage. Stress driven boundary migration in aluminium bicrystals was observed to be coupled to a tangential translation of the grains. The activation enthalpy of high angle boundary migration was found to vary non-monotonically with

Exposure to grain dust in Great Britain.

Science.gov (United States)

Spankie, Sally; Cherrie, John W

2012-01-01

Airborne grain dust is a complex mixture of fragments of organic material from grain, plus mineral matter from soil, and possible insect, fungal, or bacterial contamination or their toxic products, such as endotoxin. In the 1990s, grain workers in Britain were frequently exposed to inhalable dust >10 mg.m(-3) (8 h), with particularly high exposures being found at terminals where grain was imported or exported and in drying operations (personal exposure typically approximately 20 mg.m(-3)). Since then, the industry has made substantial progress in improving the control of airborne dust through better-designed processes, increased automation, and an improved focus on product quality. We have used information from the published scientific literature and a small survey of industry representatives to estimate current exposure levels. These data suggest that current long-term exposure to inhalable dust for most workers is on average less than approximately 3 mg.m(-3), with perhaps 15-20% of individual personal exposures being >10 mg.m(-3). There are no published data from Britain on short-term exposure during cleaning and other tasks. We have estimated average levels for a range of tasks and judge that the highest levels, for example during some cleaning activities and certain process tasks such as loading and packing, are probably approximately10 mg.m(-3). Endotoxin levels were judged likely to be dust levels are <10 mg.m(-3). There are no published exposure data on mycotoxin, respirable crystalline silica, and mite contamination but these are not considered to present widespread problems in the British industry. Further research should be carried out to confirm these findings.

Poor safety climate, long work hours, and musculoskeletal discomfort among Latino horse farm workers.

Science.gov (United States)

Swanberg, Jennifer; Clouser, Jessica Miller; Gan, Wenqi; Flunker, John C; Westneat, Susan; Browning, Steven R

2017-09-03

This study investigated the prevalence of self-reported musculoskeletal discomfort (MSD) and work-related factors associated with elevated MSD among Latino thoroughbred farm workers. Participants (N = 225) were recruited using a community-based purposive sampling approach to participate in in-person interviews. Of these workers, 85% experienced MSD. MSD was divided into tertiles; the upper tertile was defined as elevated. Multivariable Poisson regression revealed associations between any elevated MSD and longer tenure on horse farms, longer work hours, and poor safety climate. Elevated neck/back MSD was associated with longer tenure, longer work hours, and poor safety climate. Elevated upper extremity MSD was associated with age and poor safety climate. Elevated lower extremity MSD was associated with longer tenure, longer work hours, and being female. Musculoskeletal discomfort is common among these workers. Improving safety climate and minimizing long work hours is recommended.

Unusual head and neck injury in elevator: autopsy study.

Science.gov (United States)

Eren, B; Türkmen, N; Dokgöz, H

2012-10-01

Industrial injuries related to auto-load-carrying vehicles were not frequently reported in the literature. Presented case was, 31-year-old male furniture worker. Deceased was found in awkward position in furniture workshop. Victim was observed on his knees in front of the elevator, head and neck lodged within openings of the elevator, and head and neck structures compressed-guillotined by the lower platform of the elevator were detected. We presented rare case of head and neck compression by elevator. Key words: head - neck - accidents - elevator - autopsy.

Chromosome breakage in peripheral lymphocytes of thorium workers

International Nuclear Information System (INIS)

Hoegerman, S.F.; Cummins, H.T.

1979-01-01

Cytogenic analysis of 21 thorium workers and 3 controls has not shown a significant elevation in the level of chromosome breakage in the workers' peripheral lymphocytes. The observation of a single dicentric chromosome in 100-cell samples from each of two workers with relatively long periods of occupational exposure and relatively high body burdens suggests, however, that such exposure might result in increases in chromosome aberration frequency

DEVELOPMENT OF GRAIN MARKET IN UKRAINE

Directory of Open Access Journals (Sweden)

Aleksandr Maslak

2015-11-01

Full Text Available The subject of the research is a set of theoretical, methodological and practical fundamentals of organizational and economic functioning are integrated agricultural formations in the grain market of Ukraine. The methodological basis of research is the complex analysis of economic processes in the grain market in Ukraine and the world. During research we used such methods as method of systematization and comparison, statistic, economic, balance, constructive, target-oriented, and the methods of induction and deduction, analogy and comparison. Main aim of this article is the analysis of the situation on the grain market in Ukraine, defining the role of integrated agricultural formations in this market, improving the organizational-economic mechanism of its functioning, identifies ways of improving the competitiveness of Ukraine among world exporters of grain. Using results of the studies we examined trends grain market in Ukraine; influence of businesses in grain production; analysis of constraints to improve production efficiency of grain; defined domestic (internal needs of grain in Ukraine; assessed the status and expediency transformation infrastructure of the grain market of Ukraine; defined priority directions of development of the grain market in Ukraine. As a result of the preparation of articles, it is obtained the following conclusions: Ukraine is the world's largest producers and exporters of grain, the production of integrated agricultural units to a third of the total grain; technical condition of farm does not meet the needs of production; the domestic market is unable to provide the existing demand for grain production, contributing to export growth; Ukraine has a number of problems due to increased grain production, namely the shortage of storage capacity for the storage of grain, limited performance transshipment of grain in port elevators and imperfection and depreciation of transport systems; solving the existing problems is

Simulation of spring wheat responses to elevated CO2 and temperature by using CERES-wheat crop model

Directory of Open Access Journals (Sweden)

H. LAURILA

2008-12-01

Full Text Available The CERES-wheat crop simulation model was used to estimate the changes in phenological development and yield production of spring wheat (Triticum aestivum L., cv. Polkka under different temperature and CO2 growing conditions. The effects of elevated temperature (3-4°C and CO2 concentration (700 ppm as expected for Finland in 2100 were simulated. The model was calibrated for long-day growing conditions in Finland. The CERES-wheat genetic coefficients for cv. Polkka were calibrated by using the MTT Agrifood Research Finland (MTT official variety trial data (1985-1990. Crop phenological development and yield measurements from open-top chamber experiments with ambient and elevated temperature and CO2 treatments were used to validate the model. Simulated mean grain yield under ambient temperature and CO2 conditions was 6.16 t ha-1 for potential growth (4.49 t ha-1 non-potential and 5.47 t ha-1 for the observed average yield (1992-1994 in ambient open-top chamber conditions. The simulated potential grain yield increased under elevated CO2 (700 ppm to 142% (167% non-potential from the simulated reference yield (100%, ambient temperature and CO2 350 ppm. Simulations for current sowing date and elevated temperature (3°C indicate accelerated anthesis and full maturity. According to the model estimations, potential yield decreased on average to 80.4% (76.8% non-potential due to temperature increase from the simulated reference. When modelling the concurrent elevated temperature and CO2 interaction, the increase in grain yield due to elevated CO2 was reduced by the elevated temperature. The combined CO2 and temperature effect increased the grain yield to 106% for potential growth (122% non-potential compared to the reference. Simulating the effects of earlier sowing, the potential grain yield increased under elevated temperature and CO2 conditions to 178% (15 days earlier sowing from 15 May, 700 ppm CO2, 3°C from the reference. Simulation results suggest

Enhanced growth, yield and physiological characteristics of rice under elevated carbon dioxide

Science.gov (United States)

Abzar, A.; Ahmad, Wan Juliana Wan; Said, Mohd Nizam Mohd; Doni, Febri; Zaidan, Mohd Waznul Adly Mohd; Fathurahman, Zain, Che Radziah Che Mohd

2018-04-01

Carbon dioxide (CO2) is rapidly increasing in the atmosphere. It is an essential element for photosynthesis which attracts attention among scientists on how plants will perform in the rising CO2 level. Rice as one of the most important staple food in the world has been studied on the growth responses under elevated CO2. The present research was carried out to determine the growth and physiology of rice in elevated CO2 condition. This research was carried out using complete randomized design with elevated (800 ppm) and ambient CO2. Results showed that growth parameters such as plant height, tillers and number of leaves per plant were increased by elevated CO2. The positive changes in plant physiology when exposed to high CO2 concentration includes significant change (p<0.05) in yield parameters such as panicle number, grain number per panicle, biomass and 1000 grain weight under the elevated CO2 of 800 ppm.

CO2 dose–response functions for wheat grain, protein and mineral yield based on FACE and open-top chamber experiments

International Nuclear Information System (INIS)

Pleijel, Håkan; Högy, Petra

2015-01-01

Data from three Swedish open-top chamber and four German FACE experiments were combined to derive response functions for elevated CO 2 (eCO 2 ) effects on Cd, Zn, Mn, protein, grain yield, grain mass and grain number of wheat. Grain yield and grain number were increased by ∼6% and ∼7%, respectively, per 100 ppm CO 2 ; the former effect was linked to plant nitrogen status. Grain mass was not influenced by eCO 2 , whereas Cd concentration was reduced. Unlike Zn, Mn and protein, effects on Cd yield were not related to effects on grain yield. Yields of Mn, Zn and (weakly) protein were positively affected by eCO 2 . For protein, grain yield, grain mass and grain number, the results were consistent among the FACE and OTC experiments. A key conclusion was that yields of essential nutrients were enhanced (Mn > Zn > protein), although less than grain yield, which would not be expected from a simple dilution model. - Highlights: • Grain yield and grain number were positively affected by 6–7% per 100 ppm CO 2 . • Yield stimulation by CO 2 was influenced by plant nitrogen status. • Cd concentration was reduced by elevated CO 2 . • Yields of Zn, Mn and protein were stimulated by CO 2 , but less than grain yield. • A simple dilution model did not explain effects on Zn, Mn and protein. - Yields of Zn, Mn and protein were stimulated less by elevated CO 2 than grain yield, while Cd yield and grain mass were unaffected, in wheat exposed in FACE and open-top chambers

Ischaemic heart disease mortality and years of work in trucking industry workers.

Science.gov (United States)

Hart, Jaime E; Garshick, Eric; Smith, Thomas J; Davis, Mary E; Laden, Francine

2013-08-01

Evidence from general population-based studies and occupational cohorts has identified air pollution from mobile sources as a risk factor for cardiovascular disease. In a cohort of US trucking industry workers, with regular exposure to vehicle exhaust, the authors previously observed elevated standardised mortality ratios for ischaemic heart disease (IHD) compared with members of the general US population. Therefore, the authors examined the association of increasing years of work in jobs with vehicle exhaust exposure and IHD mortality within the cohort. The authors calculated years of work in eight job groups for 30,758 workers using work records from four nationwide companies. Proportional hazard regression was used to examine relationships between IHD mortality, 1985-2000, and employment duration in each job group. HRs for at least 1 year of work in each job were elevated for dockworkers, long haul drivers, pick-up and delivery drivers, combination workers, hostlers, and shop workers. There was a suggestion of an increased risk of IHD mortality with increasing years of work as a long haul driver, pick-up and delivery driver, combination worker, and dockworker. These results suggest an elevated risk of IHD mortality in workers with a previous history of regular exposure to vehicle exhaust.

Asbestos-related radiographic findings among household contacts of workers exposed to Libby vermiculite: impact of workers' personal hygiene practices.

Science.gov (United States)

Hilbert, Timothy J; Franzblau, Alfred; Dunning, Kari K; Borton, Eric K; Rohs, Amy M; Lockey, James E

2013-11-01

To explore the potential impact of worker hygiene by determining the prevalence of radiographic changes consistent with asbestos exposure among household contacts of workers exposed to Libby vermiculite that contained amphibole fibers. Workers and household contacts had chest radiographs and completed questionnaires regarding hygiene and potential exposure pathways. Participants included 191 household contacts of 118 workers. One household contact (0.5%) had localized pleural thickening, and three (1.6%) had irregular opacities at profusion category 1/0 or greater. Worker radiographs demonstrated pleural changes in 45% and irregular opacities at profusion category 1/0 or greater in 8%. Libby vermiculite-exposed workers demonstrated an elevated prevalence of pleural and interstitial chest radiographic changes. There was, however, no increased prevalence of similar changes among household contacts, likely because of personal hygiene measures taken by the majority of workers.

Competing Grain Boundary and Interior Deformation Mechanisms with Varying Sizes

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wei [University of Tennessee (UT); Gao, Yanfei [ORNL; Nieh, T. G. [University of Tennessee, Knoxville (UTK)

2018-01-01

In typical coarse-grained alloys, the dominant plastic deformations are dislocation gliding or climbing, and material strengths can be tuned by dislocation interactions with grain boundaries, precipitates, solid solutions, and other defects. With the reduction of grain size, the increase of material strengths follows the classic Hall-Petch relationship up to nano-grained materials. Even at room temperatures, nano-grained materials exhibit strength softening, or called the inverse Hall-Petch effect, as grain boundary processes take over as the dominant deformation mechanisms. On the other hand, at elevated temperatures, grain boundary processes compete with grain interior deformation mechanisms over a wide range of the applied stress and grain sizes. This book chapter reviews and compares the rate equation model and the microstructure-based finite element simulations. The latter explicitly accounts for the grain boundary sliding, grain boundary diffusion and migration, as well as the grain interior dislocation creep. Therefore the explicit finite element method has clear advantages in problems where microstructural heterogeneities play a critical role, such as in the gradient microstructure in shot peening or weldment. Furthermore, combined with the Hall-Petch effect and its breakdown, the above competing processes help construct deformation mechanism maps by extending from the classic Frost-Ashby type to the ones with the dependence of grain size.

Annual North Dakota Elevator Marketing Report, 2008-09

Science.gov (United States)

2009-12-01

The Annual North Dakota Elevator Marketing Report for 2008-09 was prepared by Kimberly Vachal and Laurel Benson, : Upper Great Plains Transportation Institute. The authors gratefully acknowledge the assistance of the North Dakota : Grain Dealers Asso...

Annual North Dakota Elevator Marketing Report, 2007-08

Science.gov (United States)

2008-12-01

The Annual North Dakota Elevator Marketing Report for 2007-08 was prepared by Kimberly Vachal and Laurel Benson, : Upper Great Plains Transportation Institute. The authors gratefully acknowledge the assistance of the North Dakota : Grain Dealers Asso...

Slope Controls Grain Yield and Climatic Yield in Mountainous Yunnan province, China

Science.gov (United States)

Duan, X.; Rong, L.; Gu, Z.; Feng, D.

2017-12-01

Mountainous regions are increasingly vulnerable to food insecurity because of limited arable land, growing population pressure, and climate change. Development of sustainable mountain agriculture will require an increased understanding of the effects of environmental factors on grain and climatic yields. The objective of this study was to explore the relationships between actual grain yield, climatic yield, and environmental factors in a mountainous region in China. We collected data on the average grain yield per unit area in 119 counties in Yunnan province from 1985 to 2012, and chose 17 environmental factors for the same period. Our results showed that actual grain yield ranged from 1.43 to 6.92 t·ha-1, and the climatic yield ranged from -0.15 to -0.01 t·ha-1. Lower climatic yield but higher grain yield was generally found in central areas and at lower slopes and elevations in the western and southwestern counties of Yunnan province. Higher climatic yield but lower grain yield were found in northwestern parts of Yunnan province on steep slopes. Annual precipation and temperature had a weak influence on the climatic yield. Slope explained 44.62 and 26.29% of the variation in grain yield and climatic yield. The effects of topography on grain and climatic yields were greater than climatic factors. Slope was the most important environmental variable for the variability in climatic and grain yields in the mountainous Yunnan province due to the highly heterogeneous topographic conditions. Conversion of slopes to terraces in areas with higher climatic yields is an effective way to maintain grain production in response to climate variability. Additionally, soil amendments and soil and water conservation measures should be considered to maintain soil fertility and aid in sustainable development in central areas, and in counties at lower slopes and elevations in western and southwestern Yunnan province.

Soil warming enhances the hidden shift of elemental stoichiometry by elevated CO2 in wheat

DEFF Research Database (Denmark)

Li, Xiangnan; Jiang, Dong; Liu, Fulai

2016-01-01

sap and their partitioning in different organs of wheat plant during grain filling were investigated. Results showed that the combination of elevated [CO2] and soil warming improved wheat grain yield, but decreased plant K, Ca and Mg accumulation and their concentrations in the leaves, stems, roots......Increase in atmospheric CO2 concentration ([CO2]) and associated soil warming along with global climate change are expected to have large impacts on grain mineral nutrition in wheat. The effects of CO2 elevation (700 μmol l(-1)) and soil warming (+2.4 °C) on K, Ca and Mg concentrations in the xylem...... and grains. The reduced grain mineral concentration was attributed to the lowered mineral uptake as exemplified by both the decreased stomatal conductance and mineral concentration in the xylem sap. These findings suggest that future higher atmospheric [CO2] and warmer soil conditions may decrease...

Prevalence of bile duct cancer among printing industry workers in comparison with other industries.

Science.gov (United States)

Okamoto, Etsuji; Kikuchi, Kiyotaka; Endo, Ginji

2013-01-01

The aim of this study was to assess the risk of developing bile duct cancer among workers in the other printing industry in comparison with workers in all industries in general. Prevalence of bile duct cancer was compared between workers in the printing industry and age-standardized controls in all other industries using the claims database of the Japan Health Insurance Association, which insures workers of small-medium sized employers of all industries. Young (aged 30-49) male workers in the printing industry showed an elevated but insignificant standardized prevalence rate ratio (SPRR) for bile duct cancer in comparison with workers in all other industries (SPRR: 1.78; 95%CI: 0.63-5.00). The risk was higher for intrahepatic bile duct cancer but remained insignificant (SPRR: 3.03; 95%CI: 0.52-17.56). The sharply elevated risk of bile duct cancer observed among proof-printing workers of a printing factory in Osaka may not be generalizable to workers in the printing industry nationwide.

3-D and quasi-2-D discrete element modeling of grain commingling in a bucket elevator boot system

Science.gov (United States)

Unwanted grain commingling impedes new quality-based grain handling systems and has proven to be an expensive and time consuming issue to study experimentally. Experimentally validated models may reduce the time and expense of studying grain commingling while providing additional insight into detail...

Increased leukemia risk in Chernobyl cleanup workers

Science.gov (United States)

A new study found a significantly elevated risk for chronic lymphocytic leukemia among workers who were engaged in recovery and clean-up activities following the Chernobyl power plant accident in 1986.

Shotgun pyrosequencing metagenomic analyses of dusts from swine confinement and grain facilities.

Science.gov (United States)

Boissy, Robert J; Romberger, Debra J; Roughead, William A; Weissenburger-Moser, Lisa; Poole, Jill A; LeVan, Tricia D

2014-01-01

Inhalation of agricultural dusts causes inflammatory reactions and symptoms such as headache, fever, and malaise, which can progress to chronic airway inflammation and associated diseases, e.g. asthma, chronic bronchitis, chronic obstructive pulmonary disease, and hypersensitivity pneumonitis. Although in many agricultural environments feed particles are the major constituent of these dusts, the inflammatory responses that they provoke are likely attributable to particle-associated bacteria, archaebacteria, fungi, and viruses. In this study, we performed shotgun pyrosequencing metagenomic analyses of DNA from dusts from swine confinement facilities or grain elevators, with comparisons to dusts from pet-free households. DNA sequence alignment showed that 19% or 62% of shotgun pyrosequencing metagenomic DNA sequence reads from swine facility or household dusts, respectively, were of swine or human origin, respectively. In contrast only 2% of such reads from grain elevator dust were of mammalian origin. These metagenomic shotgun reads of mammalian origin were excluded from our analyses of agricultural dust microbiota. The ten most prevalent bacterial taxa identified in swine facility compared to grain elevator or household dust were comprised of 75%, 16%, and 42% gram-positive organisms, respectively. Four of the top five swine facility dust genera were assignable (Clostridium, Lactobacillus, Ruminococcus, and Eubacterium, ranging from 4% to 19% relative abundance). The relative abundances of these four genera were lower in dust from grain elevators or pet-free households. These analyses also highlighted the predominance in swine facility dust of Firmicutes (70%) at the phylum level, Clostridia (44%) at the Class level, and Clostridiales at the Order level (41%). In summary, shotgun pyrosequencing metagenomic analyses of agricultural dusts show that they differ qualitatively and quantitatively at the level of microbial taxa present, and that the bioinformatic analyses

Shotgun pyrosequencing metagenomic analyses of dusts from swine confinement and grain facilities.

Directory of Open Access Journals (Sweden)

Robert J Boissy

Full Text Available Inhalation of agricultural dusts causes inflammatory reactions and symptoms such as headache, fever, and malaise, which can progress to chronic airway inflammation and associated diseases, e.g. asthma, chronic bronchitis, chronic obstructive pulmonary disease, and hypersensitivity pneumonitis. Although in many agricultural environments feed particles are the major constituent of these dusts, the inflammatory responses that they provoke are likely attributable to particle-associated bacteria, archaebacteria, fungi, and viruses. In this study, we performed shotgun pyrosequencing metagenomic analyses of DNA from dusts from swine confinement facilities or grain elevators, with comparisons to dusts from pet-free households. DNA sequence alignment showed that 19% or 62% of shotgun pyrosequencing metagenomic DNA sequence reads from swine facility or household dusts, respectively, were of swine or human origin, respectively. In contrast only 2% of such reads from grain elevator dust were of mammalian origin. These metagenomic shotgun reads of mammalian origin were excluded from our analyses of agricultural dust microbiota. The ten most prevalent bacterial taxa identified in swine facility compared to grain elevator or household dust were comprised of 75%, 16%, and 42% gram-positive organisms, respectively. Four of the top five swine facility dust genera were assignable (Clostridium, Lactobacillus, Ruminococcus, and Eubacterium, ranging from 4% to 19% relative abundance. The relative abundances of these four genera were lower in dust from grain elevators or pet-free households. These analyses also highlighted the predominance in swine facility dust of Firmicutes (70% at the phylum level, Clostridia (44% at the Class level, and Clostridiales at the Order level (41%. In summary, shotgun pyrosequencing metagenomic analyses of agricultural dusts show that they differ qualitatively and quantitatively at the level of microbial taxa present, and that the

Bleaching of the post-IR IRSL signal from individual grains of K-feldspar: Implications for single-grain dating

International Nuclear Information System (INIS)

Smedley, R.K.; Duller, G.A.T.; Roberts, H.M.

2015-01-01

Post-IR IRSL (pIRIR) signals from K-feldspar grains measured at elevated temperatures are increasingly being used for dating sediments. Unfortunately the pIRIR signal from K-feldspars bleaches more slowly than other signals (e.g. OSL from quartz) upon exposure to daylight, leading to concerns about residual signals remaining at deposition. However, earlier studies have not assessed whether the pIRIR signal bleaches at the same rate in all feldspar grains. In this study laboratory bleaching experiments have been conducted and for the first time the results show that the rate at which the pIRIR signal from individual K-feldspar grains bleach varies. To determine whether grain-to-grain variability in bleaching rate has a dominant control on equivalent dose (D e ) distributions determined using single grains, analysis was undertaken on three samples with independent age control from different depositional environments (two aeolian and one glaciofluvial). The D e value determined from each grain was compared with the rate at which the pIRIR 225 signal from the grain bleaches. The bleaching rate of each grain was assessed by giving a 52 Gy dose and measuring the residual D e after bleaching for an hour in a solar simulator. There is no clear relationship between the rate at which the pIRIR 225 signal of an individual grain bleaches and the magnitude of its D e . It is concluded that variability in the bleaching rate of the pIRIR 225 signal from one grain to another does not appear to be a dominant control on single grain D e distributions. - Highlights: • The bleaching rate of the pIRIR signal from single K-feldspar grains was assessed. • The pIRIR 225 signal bleaches more rapidly than the pIRIR 290 signal. • pIRIR 225 and pIRIR 290 signals reach the same level after 4–20 h of bleaching. • The bleaching rate of the pIRIR signal varies from one grain to another. • Variable pIRIR bleaching rates do not control single-grain D e distributions

Utilizing Secondary Agricultural Education Programs to Deliver Evidence-Based Grain Safety Training for Young and Beginning Workers.

Science.gov (United States)

Cheng, Yuan-Hsin; Field, William E; Tormoehlen, Roger L; French, Brian F

2017-01-01

Purdue University's Agricultural Safety and Health Program (PUASHP) has collaborated with secondary agricultural education programs, including FFA Chapters, for over 70 years to deliver and promote agricultural safety and health programming. With support from a U.S. Department of Labor Susan Harwood Program grant, PUASHP utilized a Developing a Curriculum (DACUM) process to develop, implement, and evaluate an evidence-based curriculum for use with young and beginning workers, ages 16-20, exposed to hazards associated with grain storage and handling. The primary audience was students enrolled in secondary agricultural education programs. A review of the literature identified a gap in educational resources that specifically addresses this target population. The curriculum developed was based on fatality and injury incident data mined from Purdue's Agricultural Confined Space Incident Database and input from a panel of experts. The process identified 27 learning outcomes and finalized a pool of test questions, supported by empirical evidence and confirmed by a panel of experts. An alignment process was then completed with the current national standards for secondary agricultural education programs. Seventy-two youth, ages 16-20, enrolled in secondary-school agricultural education programs, and a smaller group of post-secondary students under the age of 21 interested in working in the grain industry pilot tested the curriculum. Based on student and instructor feedback, the curriculum was refined and submitted to OSHA for approval as part of OSHA's online training resources. The curriculum was delivered to 3,665 students, ages 16-20. A total of 346 pre- and post-tests were analyzed, and the results used to confirm content validity and assess knowledge gain. Findings led to additional modifications to curriculum content, affirmed knowledge gain, and confirmed appropriateness for use with secondary agricultural education programs. The curriculum has been promoted

Construction Worker Fatigue Prediction Model Based on System Dynamic

Directory of Open Access Journals (Sweden)

Wahyu Adi Tri Joko

2017-01-01

Full Text Available Construction accident can be caused by internal and external factors such as worker fatigue and unsafe project environment. Tight schedule of construction project forcing construction worker to work overtime in long period. This situation leads to worker fatigue. This paper proposes a model to predict construction worker fatigue based on system dynamic (SD. System dynamic is used to represent correlation among internal and external factors and to simulate level of worker fatigue. To validate the model, 93 construction workers whom worked in a high rise building construction projects, were used as case study. The result shows that excessive workload, working elevation and age, are the main factors lead to construction worker fatigue. Simulation result also shows that these factors can increase worker fatigue level to 21.2% times compared to normal condition. Beside predicting worker fatigue level this model can also be used as early warning system to prevent construction worker accident

Microstructural design of magnesium alloys for elevated temperature performance

Science.gov (United States)

Bryan, Zachary Lee

Magnesium alloys are promising for automotive and aerospace applications requiring lightweight structural metals due to their high specific strength. Weight reductions through material substitution significantly improve fuel efficiency and reduce greenhouse gas emissions. Challenges to widespread integration of Mg alloys primarily result from their limited ductility and elevated temperature strength. This research presents a microstructurally-driven systems design approach to Mg alloy development for elevated temperature applications. The alloy properties that were targeted included creep resistance, elevated temperature strength, room temperature ductility, and material cost. To enable microstructural predictions during the design process, computational thermodynamics was utilized with a newly developed atomic mobility database for HCP-Mg. The mobilities for Mg self-diffusion, as well as Al, Ag, Sn, and Zn solute diffusion in HCP-Mg were optimized from available diffusion literature using DICTRA. The optimized mobility database was then validated using experimental diffusion couples. To limit dislocation creep mechanisms in the first design iteration, a microstructure consisting of Al solutes in solid solution and a fine dispersion of Mg2Sn precipitates was targeted. The development of strength and diffusion models informed by thermodynamic predictions of phase equilibria led to the selection of an optimum Mg-1.9at%Sn-1.5at%Al (TA) alloy for elevated temperature performance. This alloy was cast, solution treated based upon DICTRA homogenization simulations, and then aged. While the tensile and creep properties were competitive with conventional Mg alloys, the TA mechanical performance was ultimately limited because of abnormal grain growth that occurred during solution treatment and the basal Mg2Sn particle morphology. For the second design iteration, insoluble Mg2Si intermetallic particles were added to the TA alloy to provide enhanced grain boundary pinning

Implications of a North American grain marketing system for prairie transportation and elevators

Science.gov (United States)

1997-09-01

The balance of this report will examine the experiences U.S. production agriculture has had with deregulation of the transportation industry. It will highlight the evolution of the procurement segment of grain marketing, concentrating on the wheat or...

Cancer incidence among Danish brewery workers

DEFF Research Database (Denmark)

Thygesen, Lau Caspar; Albertsen, Katrine; Johansen, Christoffer

2005-01-01

in a brewery between 1939 and 1963. From the original cohort of 14,313 workers, it was possible to identify 13,051 brewery workers (91.2%). The identified brewery workers were linked to the Danish Cancer Registry for any cancer diagnoses during 1943-1999. The incidence rate of all Danish men was applied...... to calculate the expected number of cancers, standardised incidence ratios for age and time trend (O/E) were computed. A total of 3,928 cases of cancer were observed compared to 2,835.8 expected (O/E, 1.39; 95%-CI, 1.34-1.43). Significantly elevated risk of cancers was seen for cancer sites such as the buccal...

Elevated concentrations of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans and polybrominated diphenyl ethers in hair from workers at an electronic waste recycling facility in Eastern China

International Nuclear Information System (INIS)

Ma Jing; Cheng Jinping; Wang Wenhua; Kunisue, Tatsuya; Wu Minghong; Kannan, Kurunthachalam

2011-01-01

Hair samples collected from e-waste recycling workers (n = 23 males, n = 4 females) were analyzed to assess occupational exposures to polybrominated diphenyl ethers (PBDEs) and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) at a large e-waste recycling facility in Taizhou, eastern China. Hair samples from a reference population composed of residents of Shanghai (n = 11) were analyzed for comparison. The mean concentration of ΣPBDEs (range, 22.8-1020 ng/g dw; mean, 157 ng/g dw) found in hair samples from e-waste recycling workers was approximately 3 times higher than the mean determined for the reference samples. The congener profiles of PBDEs in hair from e-waste recycling workers were dominated by BDE 209, whereas the profiles in the reference-population samples showed comparable levels of BDE 47 and BDE 209. Total PCDD/F concentrations in hair from e-waste workers (range, 126-5820 pg/g dw; mean, 1670 pg/g dw) were approximately 18-fold greater than the concentrations measured in hair from the reference population. Concentrations of PCDFs were greater than concentrations of PCDDs, in all of the hair samples analyzed (samples from e-waste and non-e-waste sites). Tetrachlorodibenzofurans (TCDFs) were the major homologues in hair samples. Overall, e-waste recycling workers had elevated concentrations of both PBDEs and PCDD/Fs, indicating that they are exposed to high levels of multiple persistent organic pollutants.

Elevated concentrations of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans and polybrominated diphenyl ethers in hair from workers at an electronic waste recycling facility in Eastern China

Energy Technology Data Exchange (ETDEWEB)

Ma Jing [School of Environmental Science and Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Wadsworth Center, New York State Department of Health, and Department of Environmental Health Sciences, School of Public Health, State University of New York at Albany, Empire State Plaza, P.O. Box 509, Albany, NY 12201-0509 (United States); Applied Radiation Institute, School of Environmental and Chemical Engineering, Shanghai University, 99 Shangda Road, P.O. Box 144, Shanghai 200444 (China); Cheng Jinping; Wang Wenhua [School of Environmental Science and Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Kunisue, Tatsuya [Wadsworth Center, New York State Department of Health, and Department of Environmental Health Sciences, School of Public Health, State University of New York at Albany, Empire State Plaza, P.O. Box 509, Albany, NY 12201-0509 (United States); Wu Minghong [Applied Radiation Institute, School of Environmental and Chemical Engineering, Shanghai University, 99 Shangda Road, P.O. Box 144, Shanghai 200444 (China); Kannan, Kurunthachalam, E-mail: kkannan@wadsworth.org [Wadsworth Center, New York State Department of Health, and Department of Environmental Health Sciences, School of Public Health, State University of New York at Albany, Empire State Plaza, P.O. Box 509, Albany, NY 12201-0509 (United States); International Joint Research Center for Persistent Toxic Substances (IJRC-PTS), State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China)

2011-02-28

Hair samples collected from e-waste recycling workers (n = 23 males, n = 4 females) were analyzed to assess occupational exposures to polybrominated diphenyl ethers (PBDEs) and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) at a large e-waste recycling facility in Taizhou, eastern China. Hair samples from a reference population composed of residents of Shanghai (n = 11) were analyzed for comparison. The mean concentration of {Sigma}PBDEs (range, 22.8-1020 ng/g dw; mean, 157 ng/g dw) found in hair samples from e-waste recycling workers was approximately 3 times higher than the mean determined for the reference samples. The congener profiles of PBDEs in hair from e-waste recycling workers were dominated by BDE 209, whereas the profiles in the reference-population samples showed comparable levels of BDE 47 and BDE 209. Total PCDD/F concentrations in hair from e-waste workers (range, 126-5820 pg/g dw; mean, 1670 pg/g dw) were approximately 18-fold greater than the concentrations measured in hair from the reference population. Concentrations of PCDFs were greater than concentrations of PCDDs, in all of the hair samples analyzed (samples from e-waste and non-e-waste sites). Tetrachlorodibenzofurans (TCDFs) were the major homologues in hair samples. Overall, e-waste recycling workers had elevated concentrations of both PBDEs and PCDD/Fs, indicating that they are exposed to high levels of multiple persistent organic pollutants.

78 FR 43753 - Inspection and Weighing of Grain in Combined and Single Lots

Science.gov (United States)

2013-07-22

... USGSA regulations for shiplots, unit trains, and lash barges. This final rule allows for breaks in... the loading of the lot must be reasonably continuous, with no consecutive break in loading to exceed... superseded; (iii) The location of the grain, if at rest, or the name(s) of the elevator(s) from which or into...

Shift work at young age is associated with elevated long-term cortisol levels and body mass index.

Science.gov (United States)

Manenschijn, Laura; van Kruysbergen, Rulanda G P M; de Jong, Frank H; Koper, Jan W; van Rossum, Elisabeth F C

2011-11-01

The incidence of obesity and other features of the metabolic syndrome is increased in shift workers. This may be due to a misalignment between the internal circadian rhythm and the behavioral rhythm. The stress hormone cortisol could play a role in this phenomenon because it is secreted in a circadian rhythm, and long-term elevated cortisol leads to components of the metabolic syndrome. We compared cortisol levels in scalp hair of shift and day workers to study changes in long-term cortisol due to shift work. Hair samples were collected from 33 shift workers and 89 day workers. Cortisol was extracted from the hair samples with methanol, and cortisol levels were measured using ELISA. Height and weight were measured, and body mass index (BMI) was calculated. Shift workers had higher hair cortisol levels than day workers: 47.32 pg/mg hair [95% confidence interval (CI) = 38.37-58.21] vs. 29.72 pg/mg hair (95% CI = 26.18-33.73) (P cortisol levels were present only in younger shift workers: 48.53 pg/mg hair (95% CI = 36.56-64.29) vs. 26.42 pg/mg hair (95% CI = 22.91-30.55) (P cortisol and BMI were positively correlated (β = 0.262; P = 0.005). Shift work at a young adult age is associated with elevated long-term cortisol levels and increased BMI. Elevated cortisol levels and BMI may contribute to the increased cardiovascular risk found in shift workers.

Presenteeism among self-employed workers: Korean working conditions survey.

Science.gov (United States)

Kim, Min-Su; Park, Jae Bum; Min, Kyoung-Bok; Lee, Kyung-Jong; Kwon, Kimin

2014-01-01

Presenteeism has become a public concern recently. Thus, we aimed to understand the relationship between self-employed workers and presenteeism using a nationally representative sample of Korean workers. Using data from the Korean Working Conditions Survey conducted in 2011, a total of 43,392 workers including paid employees and self-employed workers were analyzed. The effect of employment status on presenteeism was analyzed using logistic regression analysis. The independent variables were socioeconomic characteristics, working conditions, and working environments. Among the 43,392 workers, 34,783 were paid and 8,609 were self-employed. Self-employed workers were more likely to exhibit presenteeism than were paid workers. An elevated odds ratio of 1.27 (95% CI 1.19-1.36) was found for presenteeism among self-employed workers. Being self-employed was significantly related with exhibiting presenteeism. Additional research should investigate whether other factors mediate the relationship between employment status and presenteeism as well as ways to reduce presenteeism among self-employed workers.

Microstructure-based multiscale modeling of elevated temperature deformation in aluminum alloys

International Nuclear Information System (INIS)

Krajewski, Paul E.; Hector, Louis G.; Du Ningning; Bower, Allan F.

2010-01-01

A multiscale model for predicting elevated temperature deformation in Al-Mg alloys is presented. Constitutive models are generated from a theoretical methodology and used to investigate the effects of grain size on formability. Flow data are computed with a polycrystalline, microstructure-based model which accounts for grain boundary sliding, stress-induced diffusion, and dislocation creep. Favorable agreement is found between the computed flow data and elevated temperature tensile measurements. A creep constitutive model is then fit to the computed flow data and used in finite-element simulations of two simple gas pressure forming processes, where favorable results are observed. These results are fully consistent with gas pressure forming experiments, and suggest a greater role for constitutive models, derived largely from theoretical methodologies, in the design of Al alloys with enhanced elevated temperature formability. The methodology detailed herein provides a framework for incorporation of results from atomistic-scale models of dislocation creep and diffusion.

Respiratory Symptoms and Lung Function in Poultry Confinement Workers in Western Canada

OpenAIRE

Kirychuk, Shelley P; Senthilselvan, Ambikaipakan; Dosman, James A; Juorio, Victor; Feddes, John JR; Willson, Philip; Classen, Henry; Reynolds, Stephen J; Guenter, Wilhelm; Hurst, Thomas S

2003-01-01

OBJECTIVE: To determine whether poultry production methods impact respiratory health, and whether poultry farmers have more respiratory symptoms and lower lung function than comparison control groups.DESIGN: Cross-sectional study.SETTING: Provinces of Saskatchewan, Alberta and Manitoba during the winters of 1997 to 1999. POPULATION: Three hundred three poultry workers, 241 grain farmers and 206 nonfarming control subjects were studied. Poultry workers were further classified according to the ...

Effect of grain size upon the fatigue-crack propagation behavior of alloy 718 under hold-time cycling at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

James, L A

1986-01-01

Fatigue-crack propagation tests were conducted in air at 538/sup 0/C on several specimens of Alloy 718 representing several different producers, melt practices and product forms. This variety resulted in a range of grain sizes from ASTM Size 5 to 11.5. Tests at low cyclic frequency employing a tensile hold-time revealed a relationship between crack growth rates and grain size: higher growth rates were associated with fine-grain material and lower rates with larger-grain material. The lowest crack growth rates were associated with a necklace microstructure, whereby large grains are associated with necklaces of very small grains.

Soil warming enhances the hidden shift of elemental stoichiometry by elevated CO2 in wheat.

Science.gov (United States)

Li, Xiangnan; Jiang, Dong; Liu, Fulai

2016-03-22

Increase in atmospheric CO2 concentration ([CO2]) and associated soil warming along with global climate change are expected to have large impacts on grain mineral nutrition in wheat. The effects of CO2 elevation (700 μmol l(-1)) and soil warming (+2.4 °C) on K, Ca and Mg concentrations in the xylem sap and their partitioning in different organs of wheat plant during grain filling were investigated. Results showed that the combination of elevated [CO2] and soil warming improved wheat grain yield, but decreased plant K, Ca and Mg accumulation and their concentrations in the leaves, stems, roots and grains. The reduced grain mineral concentration was attributed to the lowered mineral uptake as exemplified by both the decreased stomatal conductance and mineral concentration in the xylem sap. These findings suggest that future higher atmospheric [CO2] and warmer soil conditions may decrease the dietary availability of minerals from wheat crops. Breeding wheat cultivars possessing higher ability of mineral uptake at reduced xylem flux in exposure to climate change should be a target.

Development of a self-consistent model of dust grain charging at elevated pressures using the method of moments

International Nuclear Information System (INIS)

Filippov, A.V.; Dyatko, N.A.; Pal', A.F.; Starostin, A.N.

2003-01-01

A model of dust grain charging is constructed using the method of moments. The dust grain charging process in a weakly ionized helium plasma produced by a 100-keV electron beam at atmospheric pressure is studied theoretically. In simulations, the beam current density was varied from 1 to 10 6 μA/cm 2 . It is shown that, in a He plasma, dust grains of radius 5 μm and larger perturb the electron temperature only slightly, although the reduced electric field near the grain reaches 8 Td, the beam current density being 10 6 μA/cm 2 . It is found that, at distances from the grain that are up to several tens or hundreds of times larger than its radius, the electron and ion densities are lower than their equilibrium values. Conditions are determined under which the charging process may be described by a model with constant electron transport coefficients. The dust grain charge is shown to be weakly affected by secondary electron emission. In a beam-produced helium plasma, the dust grain potential calculated in the drift-diffusion model is shown to be close to that calculated in the orbit motion limited model. It is found that, in the vicinity of a body perturbing the plasma, there may be no quasineutral plasma presheath with an ambipolar diffusion of charged particles. The conditions for the onset of this presheath in a beam-produced plasma are determined

Mechanical Properties and Fracture Behaviors of the As-Extruded Mg-5Al-3Ca Alloys Containing Yttrium at Elevated Temperature.

Science.gov (United States)

Son, Hyeon-Taek; Kim, Yong-Ho; Kim, Taek-Soo; Lee, Seong-Hee

2016-02-01

Effects of yttrium (Y) addition on mechanical properties and fracture behaviors of the as-extruded Mg-Al-Ca based alloys at elevated temperature were investigated by a tensile test. After hot extrusion, the average grain size was refined by Y addition and eutectic phases were broken down into fine particles. Y addition to Mg-5Al-3Ca based alloy resulted in the improvement of strength and ductility at elevated temperature due to fine grain and suppression of grain growth by formation of thermally stable Al2Y intermetallic compound.

29 CFR 780.711 - Exemption of mixed business applies only to country elevators.

Science.gov (United States)

2010-07-01

... used in the operation of a farm does not extend the exemption to an establishment selling products and... to exempting country elevators that market farm products, mostly grain, for farmers who are working long workweeks and need to have the elevator facilities open and available for disposal of their crops...

Plastic creep flow processes in fracture at elevated temperatures

International Nuclear Information System (INIS)

Rice, J.R.

1979-01-01

Recent theoretical developments on fracture at elevated temperature in the presence of overall plastic (dislocation) creep are discussed. Two topics are considered: stress fields at tips of macroscopic cracks in creeping solids; and diffusive growth of microscopic grain boundary cavities in creeping solids

Mortality among workers at the Mound Facility: A preliminary report

International Nuclear Information System (INIS)

Reyes, M.; Wilkinson, G.S.; Tietjen, G.L.; Wiggs, L.D.; Galke, W.A.

1991-04-01

Mortality among 4,697 white males who were employed at the Mound Facility between 1943 and 1979 was compared with expected mortality based on US white male death rates. Standardized mortality ratios (SMRs) of 96 were observed for both all causes and all cancers. SMRs for digestive cancers and unintentional injuries were significantly less than 100. No SMR was significantly greater than 100 for these workers. A significantly elevated lung cancer SMR was observed for the subcohort of workers employed from 1943--1959, a period during which polonium-210 was processed at the plant. To determine the potential impact of wartime selection factors, this time period was further divided into two periods, 1943--1945 and 1946--1959. In the 1943--1945 period, the SMR for lung cancer was 204 (90% CI = 140, 290), while in the later period the lung cancer SMR was 105 (90% CI = 77, 140). Similar results were observed for all causes, all cancers, cancers of the rectum, nonmalignant respiratory diseases, and all injuries for which the SMRs were elevated during the wartime period but were not elevated after the war. Additional analyses considering workers hired in the period 1960--1979, during which plutonium-238 was processed at the facility, yielded little information. Generally, a strong healthy worker effect was observed and was attributed to the limited follow-up time and small numbers of deaths among this subcohort. 22 refs., 9 tabs

Eryptosis in lead-exposed workers

International Nuclear Information System (INIS)

Aguilar-Dorado, Itzel-Citlalli; Hernández, Gerardo; Quintanar-Escorza, Martha-Angelica; Maldonado-Vega, María; Rosas-Flores, Margarita; Calderón-Salinas, José-Víctor

2014-01-01

externalization • Elevated eryptosis in lead intoxicated workers may be induced by higher oxidation • Lead intoxication induces eryptosis by depletion of GSH • Lead exposition induces eryptosis through an increment of erythrocyte [Cai 2+ ] i

Eryptosis in lead-exposed workers

Energy Technology Data Exchange (ETDEWEB)

Aguilar-Dorado, Itzel-Citlalli [Biochemistry Department, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico); Hernández, Gerardo [Section of Methodology of Science, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico); Quintanar-Escorza, Martha-Angelica [Faculty of Medicine, UJED, Durango, DGO (Mexico); Maldonado-Vega, María [CIATEC, León, GTO (Mexico); Rosas-Flores, Margarita [Biochemistry Department, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico); Calderón-Salinas, José-Víctor, E-mail: jcalder@cinvestav.mx [Biochemistry Department, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico)

2014-12-01

showed higher PS externalization • Elevated eryptosis in lead intoxicated workers may be induced by higher oxidation • Lead intoxication induces eryptosis by depletion of GSH • Lead exposition induces eryptosis through an increment of erythrocyte [Cai{sup 2+}]{sub i}.

[The epidemiological validation of the MPEL for grain dust in the atmosphere].

Science.gov (United States)

Pinigin, M A; Cherepov, E M; Safiulin, A A; Petrova, I V; Mukhambetova, L Kh; Osipova, E M; Veselov, A P

1998-01-01

The use of calculating and gravimetric methods for examining the grain dust pollution of the ambient air at the site of an elevator determined the maximum single, mean daily, and mean annual concentrations at different distances from the source of dust emission. The mean ratio of these concentrations was 12.1:4.3:1, respectively. The calculated concentration-effect and concentration-time relationships provided evidence for the maximum single, mean daily, and mean annual allowable concentrations for grain dust in the ambient air.

Sensitivity of metrics of phylogenetic structure to scale, source of data and species pool of hummingbird assemblages along elevational gradients.

Directory of Open Access Journals (Sweden)

Sebastián González-Caro

Full Text Available Patterns of phylogenetic structure of assemblages are increasingly used to gain insight into the ecological and evolutionary processes involved in the assembly of co-occurring species. Metrics of phylogenetic structure can be sensitive to scaling issues and data availability. Here we empirically assess the sensitivity of four metrics of phylogenetic structure of assemblages to changes in (i the source of data, (ii the spatial grain at which assemblages are defined, and (iii the definition of species pools using hummingbird (Trochilidae assemblages along an elevational gradient in Colombia. We also discuss some of the implications in terms of the potential mechanisms driving these patterns. To explore how source of data influence phylogenetic structure we defined assemblages using three sources of data: field inventories, museum specimens, and range maps. Assemblages were defined at two spatial grains: coarse-grained (elevational bands of 800-m width and fine-grained (1-km(2 plots. We used three different species pools: all species contained in assemblages, all species within half-degree quadrats, and all species either above or below 2000 m elevation. Metrics considering phylogenetic relationships among all species within assemblages showed phylogenetic clustering at high elevations and phylogenetic evenness in the lowlands, whereas those metrics considering only the closest co-occurring relatives showed the opposite trend. This result suggests that using multiple metrics of phylogenetic structure should provide greater insight into the mechanisms shaping assemblage structure. The source and spatial grain of data had important influences on estimates of both richness and phylogenetic structure. Metrics considering the co-occurrence of close relatives were particularly sensitive to changes in the spatial grain. Assemblages based on range maps included more species and showed less phylogenetic structure than assemblages based on museum or field

The interactive effects of elevated CO2, temperature and N supply on rice yield

International Nuclear Information System (INIS)

Baysa, Marieta C.; Tremmel, David C.; Reynolds, James F.; Rivero, Gilda C.; Tabbada, Reynaldo A.

2001-01-01

Rice (Oryza sativa L. cv. IR 72)was grown in growth chambers under combinations of two CO 2 (375 and 750 μL L -1 ), temperature(29/21 and 34/26 degrees centigrade day/night) and N (40 and 80 mg L -1 ) regimes from sowing until grain maturity. Panicle production was significantly enhanced by elevated CO 2 with more pronounced effects at high temperature and N. CO 2 -enriched plants grown at high temperatures had lower harvest indices due to reductions in the number of grains per panicle and grain mass. Any potential benefit of increased atmospheric CO 2 on rice grain yield and grain N content under optimal N supply may therefore be dampened by higher temperatures associated with possible future global warming conditions. (Author)

Radiation disinfestation of grain in a port elevator with capacity of 400 T/h

Energy Technology Data Exchange (ETDEWEB)

Zakladnoy, G.A.; Menshenin, A.I.; Pertsovsky, E.S. (VNPO ' ' Zernoprodukt' ' , Moscow (USSR)); Salimov, R.A.; Cherepkov, V.G. (AN SSSR, Novosibirsk (USSR). Inst. Yadernoj Fiziki); Bogolyubov, B.F.; Stanev, I.S. (Odessa Port Elevator (USSR))

1989-01-01

In the work presented here the study of radiation disinfestation of grain carried out in the USSR is given. Parameters of radiation disinfestors and the ELV-type electron accelerators are described. Practical experience in this field in the U.S.S.R. is also described. (author).

Oxidative Role of Aflatoxin B1 on the Liver of Wheat Milling Workers

Directory of Open Access Journals (Sweden)

Amal Saad-Hussein

2014-03-01

Full Text Available Aim: The study aimed to estimate oxidative role of aflatoxin B1 (AFB1 on the liver in wheat milling workers. Materials and Methods: Case-control study was conducted to compare between the levels of AFB1/albumin (AFB1/alb, liver enzymes (ALT, AST, GGT, and ALP, P53, MDA, GST, SOD, zinc and vitamin C in 35 wheat milling workers and 40 control subjects. Results: Statistical analysis revealed that ALT, AST, GGT, ALP, P53, MDA, GST and SOD in workers were significantly elevated compared to their controls. In the milling workers, there were significant correlations between MDA levels and the levels of AST, GGT, and P53, while, P53 was inversely correlated with GST and SOD activities. There were significant correlations between Zn levels and GGT, GST and SOD activities, between vitamin C and GST activities, and vitamin C inversely correlated with MDA. Conclusion: The present study concluded that the oxidative stress of AFB1 elevated the MDA and the liver enzymes in wheat milling workers. GST has a crucial role in the detoxification of aflatoxin and SOD as a scavenger antioxidant increased in the workers to overcome the oxidative toxic effects of AFB1 on the liver of the workers, and roles of Zn and vitamin C were significant in activation of these processes.

Oxylipins discriminate between whole grain wheat and wheat aleurone intake: a metabolomics study on pig plasma

DEFF Research Database (Denmark)

Nørskov, Natalja; Hedemann, Mette Skou; Theil, Peter Kappel

2013-01-01

were also found in the flour and the bread consumed by pigs. Since the germ is part of the whole grain flour, the germ is most likely responsible for the elevated level of oxylipins in plasma after whole grain wheat consumption. This finding may also point towards bioactive compounds, which can be used......A pig model was used to investigate the difference in metabolic response of plasma between whole grain wheat and wheat aleurone. Six pigs were fed in a cross-over design iso dietary fiber (DF) breads prepared from whole grain wheat and wheat aleurone and with a wash-out diet based on bread produced...

Chromosome aberrations in pesticide-exposed greenhouse workers

DEFF Research Database (Denmark)

Lander, B F; Knudsen, Lisbeth E.; Gamborg, M O

2000-01-01

OBJECTIVES: The aim of this study was to investigate the possibility of subtoxic exposure to pesticides causing chromosome aberrations in greenhouse workers. METHODS: In a cross-sectional and prospective study design chromosome aberration frequencies in cultured lymphocytes were examined for 116...... greenhouse workers exposed to a complex mixture of almost 50 insecticides, fungicides, and growth regulators and also for 29 nonsmoking, nonpesticide-exposed referents. RESULTS: The preseason frequencies of chromosome aberrations were slightly but not statistically significantly elevated for the greenhouse...... workers when they were compared with the referents. After a summer season of pesticide spraying in the greenhouses, the total frequencies of cells with chromosome aberrations were significantly higher than in the preseason samples (P=0.02) and also higher than for the referents (P=0.05). This finding...

Earning While Learning: Maintaining Income While Upgrading Skills. Advancement for Low-Wage Workers

Science.gov (United States)

Prince, Heath

2004-01-01

Drawing on innovative workforce development efforts around the country, Jobs for the Future (JJF) publications, tool kits, and other resources respond to the challenges to advancement for low-wage workers. Occasional papers in the series Advancement for Low-Wage Workers seeks to elevate discussion of this issue within and outside the workforce…

GWAS of Barley Phenotypes Established Under Future Climate Conditions of Elevated Temperature, CO2, O3 and Elevated Temperature and CO2 Combined

DEFF Research Database (Denmark)

Ingvordsen, Cathrine Heinz; Backes, G.; Lyngkjær, M. F.

2015-01-01

Climate change is likely to decrease crop yields worldwide. Developing climate resilient cultivars is one way to combat this production scarcity, however, little is known of crop response to future climate conditions and in particular the variability within crops.In Scandinavia, barley is widely...... cultivated, but yields have stagnated since the start of this century. In this study we cultivated 138 spring barley accessions in a climate phytotron under four treatments mimicking forecasted levels of temperature, carbon dioxide concentration ([CO2]) and ozone ([O3]) at the end of the 21st century1...... yield, grain protein concentration, grain protein harvested, number of grains, number of ears, aboveground vegetative biomass and harvest index. In addition, stability of the production was calculated over the applied treatments for the assessed parameters.In the climate scenario of elevated temperature...

Effect of replacing maize grain and soybean meal with a xylose-treated wheat grain on feed intake and performance of dairy cows.

Science.gov (United States)

Benninghoff, Jens; Hamann, Gregor; Steingaß, Herbert; Romberg, Franz-Josef; Landfried, Karl; Südekum, Karl-Heinz

2017-06-01

This study evaluated wheat grain which was treated with xylose in aqueous Ca-Mg lignosulphonate solution at elevated temperatures (WeiPass®) in order to reduce ruminal degradation of starch and crude protein. The two tested isoenergetic and isonitrogenous diets contained on dry matter (DM) basis either 16% maize grain and 6.4% soybean meal (Diet CON) or 17.8% xylose-treated wheat and 4.6% soybean meal (Diet Wheat). Thirty-six German Holstein dairy cows were assigned to one of the two groups according to parity, body weight after calving, and milk yield during the previous lactation. Data collection started at 21 d before the expected calving date until 120 d in milk. The average of DM intake, energy-corrected milk (ECM) yield, and milk fat and protein yields (all given as kg/d) were 18.9, 28.7, 1.25, and 1.02 for Diet CON and 19.3, 32.5, 1.36, and 1.11 for Diet Wheat, respectively. Only ECM and milk protein yields were greater (p < 0.05) for cows receiving Diet Wheat. In conclusion, the xylose-treated wheat grain can replace maize grain and part of soybean meal in diets for lactating dairy cows and may be an alternative feedstuff depending on overall ration composition and availability and costs of grain sources.

High annealing temperature induced rapid grain coarsening for efficient perovskite solar cells.

Science.gov (United States)

Cao, Xiaobing; Zhi, Lili; Jia, Yi; Li, Yahui; Cui, Xian; Zhao, Ke; Ci, Lijie; Ding, Kongxian; Wei, Jinquan

2018-08-15

Thermal annealing plays multiple roles in fabricating high quality perovskite films. Generally, it might result in large perovskite grains by elevating annealing temperature, but might also lead to decomposition of perovskite. Here, we study the effects of annealing temperature on the coarsening of perovskite grains in a temperature range from 100 to 250 °C, and find that the coarsening rate of the perovskite grain increase significantly with the annealing temperature. Compared with the perovskite films annealed at 100 °C, high quality perovskite films with large columnar grains are obtained by annealing perovskite precursor films at 250 °C for only 10 s. As a result, the power conversion efficiency of best solar cell increased from 12.35% to 16.35% due to its low recombination rate and high efficient charge transportation in solar cells. Copyright © 2018. Published by Elsevier Inc.

Cardiotoxicity of Freon among refrigeration services workers: comparative cross-sectional study

Science.gov (United States)

2009-01-01

Background Freon includes a number of gaseous, colorless chlorofluorocarbons. Although freon is generally considered to be a fluorocarbon of relatively low toxicity; significantly detrimental effects may occur upon over exposure. The purpose of the present study is to investigate whether occupational exposure to fluorocarbons can induce arterial hypertension, myocardial ischemia, cardiac arrhythmias, elevated levels of plasma lipids and renal dysfunction. Methods This comparative cross-sectional study was conducted at the cardiology clinic of the Suez Canal Authority Hospital (Egypt). The study included 23 apparently healthy male workers at the refrigeration services workshop who were exposed to fluorocarbons (FC 12 and FC 22) and 23 likewise apparently healthy male workers (unexposed), the control group. All the participants were interviewed using a pre-composed questionnaire and were subjected to a clinical examination and relevant laboratory investigations. Results There were no significant statistical differences between the groups studied regarding symptoms suggesting arterial hypertension and renal affection, although a significantly higher percentage of the studied refrigeration services workers had symptoms of arrhythmias. None of the workers had symptoms suggesting coronary artery disease. Clinical examination revealed that the refrigeration services workers had a significantly higher mean pulse rate compared to the controls, though no significant statistical differences were found in arterial blood pressure measurements between the two study groups. Exercise stress testing of the workers studied revealed normal heart reaction to the increased need for oxygen, while sinus tachycardia was detected in all the participants. The results of Holter monitoring revealed significant differences within subject and group regarding the number of abnormal beats detected throughout the day of monitoring (p < 0.001). There were no significant differences detected in the

Effect of continuous change of sintering atmosphere on the grain growth of Cr-doped UO2 pellets

International Nuclear Information System (INIS)

Yang, Jae Ho; Nam, Ik Hui; Kim, Jong Hun; Rhee, Young Woo; Kim, Dong Joo; Kim, Keon Sik; Song, Kun Woo

2010-01-01

Cr-doped UO 2 pellet is one of the promising candidates for the high burn-up fuel in commercial LWRs. Major nuclear fuel vendors of such as AREVA or Westinghouse initiated the development of Cr-doped or Cr-containing additives doped UO 2 pellets since at the mid of 90's. Now, qualification programs are on-going to provide these pellets commercially. The main characteristics of the Cr-doped pellets are large-grain and visco-plasticity. Large grain pellet can reduce the corrosive fission gas release at high burn up. Viscoplastic soft pellets can lower the pressure to a cladding caused by a thermal expansion of a pellet at an elevated temperature during transient operations. Those advantages can provide room for additional power uprates and high burnup limits. Especially, PCI resistance improvement can be achieved by enlarging the pellet grain size and enhancing the fuel deformation at an elevated temperature. In this paper, to study the effect of oxygen partial pressure on grain growth in Cr-doped UO 2 pellets, Cr- doped UO 2 samples have been sintered with and without a step-wise change of sintering atmospheres. An introduction of a step-wise variation of oxygen partial pressure during the sintering enhances the grain growth of UO 2 pellets greatly. This step-wise sintering effect has been explained in terms of a continuous increase of Cr concentration along the grain boundary. The observed grain growth behavior under step-wisely changed sintering atmospheres demonstrates the possibility of reducing the amount of Cr 2 O 3 to minimum via control of oxygen partial pressure while keeping the large grain size

Investigation of bias in a study of nuclear shipyard workers

International Nuclear Information System (INIS)

Greenberg, E.R.; Rosner, B.; Hennekens, C.; Rinsky, R.; Colton, T.

1985-01-01

The authors examined discrepant findings between a 1978 proportional mortality study and a 1981 cohort study of workers at the Portsmouth, New Hampshire Naval Shipyard to determine whether the healthy worker effect, selection bias, or measurement bias could explain why only the proportional mortality study found excess cancer deaths among nuclear workers. Lower mortality from noncancer causes in nuclear workers (the healthy worker effect) partly accounted for the observed elevated cancer proportional mortality. More important, however, was measurement bias which occurred in the proportional mortality study when nuclear workers who had not died of cancer were misclassified as not being nuclear workers based on information from their next of kin, thereby, creating a spurious association. Although the proportional mortality study was based on a small sample of all deaths occuring in the cohort, selection bias did not contribute materially to the discrepant results for total cancer deaths. With regard to leukemia, misclassification of occupation in the proportional mortality study and disagreement about cause of death accounted for some of the reported excess deaths. 16 references, 4 tables

Occupational asthma and IgE sensitization to grain dust.

Science.gov (United States)

Park, H S; Nahm, D H; Suh, C H; Kwon, O Y; Kim, K S; Lee, S W; Chung, H K

1998-06-01

To evaluate type I hypersensitivity to grain dust (GD), its prevalence and relationship to respiratory dysfunction, we studied clinical and immunologic features, including skin prick tests (SPT), serum specific IgE, and bronchoprovocation tests of 43 employees working in the animal feed industry. To further characterize IgE-mediated reaction, SDS-PAGE and electroblot studies were performed. Our survey revealed that 15 (34.9%) subjects had work-related skin response (> or =2+ of A/H ratio) to GD, thirteen (30.2%) had high specific IgE antibody against GD. The specific IgE antibody was detected more frequently in symptomatic workers (40%) than in asymptomatic workers (11%). Significant association was found between specific IgE antibody and atopy or smoking (pdust mite, storage mite and corn dust. Immunoblot analysis showed 8 IgE binding components within GD ranging from 13.5 to 142.5 kDa. Two bands (13.5, 33 kDa) were bound to the IgE from more than 50% of the 14 sera tested. In conclusion, these findings suggest that GD inhalation could induce IgE-mediated bronchoconstriction in exposed workers.

Carcinogenic risk for workers exposed to ionizing radiation. A critical review of present epidemiologic studies

International Nuclear Information System (INIS)

Tirmarche, M.

1987-01-01

Epidemiologic studies on workers who have been exposed to ionizing radiation have allowed to demonstrate certain cancer risks associated with elevated, often retrospectively reconstituted exposures. Present studies on still active workers or workers having worked for the last 15 years are indispensable to define the risk associated with low irradiation doses; they must, however, take into account confounding factors that may play a role in the etiology of the cancer studied

Mortality among California highway workers.

Science.gov (United States)

Maizlish, N; Beaumont, J; Singleton, J

1988-01-01

Standardized proportional mortality ratios (PMR) were computed for a population of highway workers. Hazards of highway maintenance work include exposure to solvents, herbicides, asphalt and welding fumes, diesel and auto exhaust, asbestos, abrasive dusts, hazardous material spills, and moving motor vehicles. Underlying cause of death was obtained for 1,570 workers who separated from the California Department of Transportation between 1970 and 1983, and who died in California between 1970 and 1983 (inclusive). Among 1,260 white males, the major findings were statistically significant excesses of cancers of digestive organs (PMR = 128), skin (PMR = 218), lymphopoietic cancer (PMR = 157), benign neoplasms (PMR = 343), motor vehicle accidents (PMR = 141), and suicide (PMR = 154). Black males (N = 66) experienced nonsignificant excesses of cancer of the digestive organs (PMR = 191) and arteriosclerotic heart disease (PMR = 143). Among 168 white females, deaths from lung cancer (PMR = 189) and suicide (PMR = 215) were elevated. White male retirees, a subgroup with 5 or more years of service, experienced excess mortality due to cancers of the colon (PMR = 245), skin (PMR = 738), brain (PMR = 556), and lymphosarcomas and reticulosarcomas (PMR = 514). Deaths from external causes (PMR = 135) and cirrhosis of the liver (PMR = 229) were elevated among white males with a last job in landscape maintenance. White males whose last job was highway maintenance experienced a deficit in mortality from circulatory diseases (PMR = 83) and excess mortality from emphysema (PMR = 250) and motor vehicle accidents (PMR = 196). Further epidemiologic and industrial hygiene studies are needed to confirm the apparent excess mortality and to quantify occupational and nonoccupational exposures. However, reduction of recognized hazards among highway maintenance workers is a prudent precautionary measure.

Film grain synthesis and its application to re-graining

Science.gov (United States)

Schallauer, Peter; Mörzinger, Roland

2006-01-01

Digital film restoration and special effects compositing require more and more automatic procedures for movie regraining. Missing or inhomogeneous grain decreases perceived quality. For the purpose of grain synthesis an existing texture synthesis algorithm has been evaluated and optimized. We show that this algorithm can produce synthetic grain which is perceptually similar to a given grain template, which has high spatial and temporal variation and which can be applied to multi-spectral images. Furthermore a re-grain application framework is proposed, which synthesises based on an input grain template artificial grain and composites this together with the original image content. Due to its modular approach this framework supports manual as well as automatic re-graining applications. Two example applications are presented, one for re-graining an entire movie and one for fully automatic re-graining of image regions produced by restoration algorithms. Low computational cost of the proposed algorithms allows application in industrial grade software.

Lung cancer risk among construction workers in California, 1988-2007.

Science.gov (United States)

Calvert, Geoffrey M; Luckhaupt, Sara; Lee, Soo-Jeong; Cress, Rosemary; Schumacher, Pam; Shen, Rui; Tak, SangWoo; Deapen, Dennis

2012-05-01

Although lung cancer risks can vary by race/ethnicity and by construction occupation, these risks have not been examined extensively. This study analyzed 110,937 lung cancer cases identified from the California Cancer Registry between 1988 and 2007. Mean age at diagnosis, proportion diagnosed at an advanced stage, and proportion with 3-year survival were calculated for lung cancer cases employed in the construction industry. Case-control methodology was also used to assess the risk of lung cancer. Morbidity odds ratios (MORs) were estimated by conditional logistic regression. Construction workers were found to have a significantly elevated risk for all lung cancer combined (MOR = 1.57) and for each lung cancer histologic subtype examined. All construction occupations, except managers/engineers and supervisors, had a significantly elevated risk for all lung cancer combined. Roofers and welders had the highest risks for total lung cancer and for each of the histologic subtypes. Construction workers in each of the four race/ethnicity groups also had significantly increased lung cancer risks. Compared to non-construction workers, construction workers were diagnosed at an earlier age, at a more advanced stage, and had significantly lower 3-year survival, though differences were modest. These findings justify additional reductions in carcinogenic exposures in construction, and increased support for smoking cessation programs at construction sites. Copyright © 2012 Wiley Periodicals, Inc.

Dust grain charging in a wake of other grains

International Nuclear Information System (INIS)

Miloch, W. J.; Block, D.

2012-01-01

The charging of dust grain in the wake of another grains in sonic and supersonic collisionless plasma flows is studied by numerical simulations. We consider two grains aligned with the flow, as well as dust chains and multiple grain arrangements. It is found that the dust charge depends significantly on the flow speed, distance between the grains, and the grain arrangement. For two and three grains aligned, the charges on downstream grains depend linearly on the flow velocity and intergrain distance. The simulations are carried out with DiP3D, a three dimensional particle-in-cell code with both electrons and ions represented as numerical particles [W. J. Miloch et al., Phys. Plasmas 17, 103703 (2010)].

A follow-up comparison of blood lead levels between foreign and native workers of battery manufacturing in Taiwan

International Nuclear Information System (INIS)

Chuang, H.-Y.; Cheng, W.-C.; Chen, C.-Y.; Yang, Y.-H.; Sung, F.-C.; Yang, C.-Y.; Wu, T.-N.

2008-01-01

Foreign workers employed in industries in Taiwan have been found at elevated risk of injuries. Less well known is whether the elevated risk persists in chemical exposure such as lead exposure at battery manufacturing. A cohort of 70 Thai workers and 55 native workers employed at a battery plant were followed up, after an education of job safety, from 2000 until 2002. This study compared the change of blood lead levels (BLLs) between these two groups of workers. With informed consent, BLLs were measured annually for participants and compared. The average baseline BLLs were approximately at similarly high levels between Thai workers and native workers with means ± standard deviations of 36.9 ± 16.4 and 36.2 ± 12.4 μg/dl, respectively (p = 0.79). At the end of 2002, the average concentration was higher in Thai workers than in native workers. Using mixed models, Thai workers had an average of 5.95 μg/dl increase in BLLs over native workers during the 3-year study. Further measurements revealed that the average BLL for workers in the assembly department was 3.57 ± 1.83 μg/dl in excess, compared with workers in the plate engineering department. Thai workers were more likely to drink alcohol but less likely to wear gloves at work and wash hands before meals. The BLL disparities between Thai workers and native workers can partly be explained by differences in risk-taking behaviors. Higher BLLs in Thai workers suggest the need of language appropriate health education to improve their personal hygiene. Workplace smoking ceasing program may be needed both in Thai and native workers

High mature grain phytase activity in the Triticeae has evolved by duplication followed by neofunctionalization of the purple acid phosphatase phytase (PAPhy) gene

DEFF Research Database (Denmark)

Madsen, Claus Krogh; Dionisio, Giuseppe; Holme, Inger

2013-01-01

The phytase activity in food and feedstuffs is an important nutritional parameter. Members of the Triticeae tribe accumulate purple acid phosphatase phytases (PAPhy) during grain filling. This accumulation elevates mature grain phytase activities (MGPA) up to levels between ~650 FTU/kg for barley...

Interactive mechanism of working environments and construction behaviors with cognitive work analysis: an elevator installation case study.

Science.gov (United States)

Wang, Yanqing; Chong, Heap-Yih; Liao, Pin-Chao; Ren, Hantao

2017-09-25

Unsafe behavior is a leading factor in accidents, and the working environment significantly affects behaviors. However, few studies have focused on detailed mechanisms for addressing unsafe behaviors resulting from environmental constraints. This study aims to delineate these mechanisms using cognitive work analysis (CWA) for an elevator installation case study. Elevator installation was selected for study because it involves operations at heights: falls from heights remain a major cause of construction worker mortality. This study adopts a mixed research approach based on three research methodology stages. This research deconstructs the details of the working environment, the workers' decision-making processes, the strategies chosen given environmental conditions and the conceptual model for workers' behaviors, which jointly depict environment-behavior mechanisms at length. By applying CWA to the construction industry, environmental constraints can easily be identified, and targeted engineering suggestions can be generated.

Relationships between the climate change and the grain filling of winter wheat

International Nuclear Information System (INIS)

Shang, Z.; Jiang, D.

2016-01-01

The present study is based on the material in a grain filling rate experiment of winter wheat and hourly weather data organised by Xinghua city of Jiangsu Province. The aims are to objectively evaluate the possible influences of the temperature, precipitation, sunshine at the different time of the same day on the grain filling rate of winter wheat. The grain filling rate evaluation model of climate change is firstly developed, and then, the model calculation results are compared with the observed data. The along the changes of the microclimate, changes of the grain filling rate of winter wheat, which is not same in the gradual, rapid and slow increase stages. The changes in grain filling rate of winter wheat, which were caused by variations of temperature, precipitation and sunshine duration, showed periodic fluctuation. Variation in temperature resulted in 1.36 g d/sup -1/(10a)/sup -1/ of grain filling rate change; variation in precipitation resulted in -1.35 g d/sup -1/. (10a)/sup -1/ of grain filling rate change; and variation in sunshine duration resulted in 0.07 g d/sup -1/ (10a)/sup -1/ of grain filling rate change. Three samples showed a grain filling rate change of 0.08 g d/sup -1/(10a)/sup -1/. These findings indicate that the increase in temperature and sunshine duration caused the elevation of grain filling rate, whereas the increase in precipitation decreased the grain filling rate. Therefore, monitoring and predication capability of Meteorological disasters, such as drought caused by high temperature, should be strengthened to ensure the favourable weather condition and improve the grain filling rate through scientific methods such as artificial precipitation. (author)

Mortality of workers employed in shoe manufacturing: an update.

Science.gov (United States)

Lehman, Everett J; Hein, Misty J

2006-07-01

In the late 1970s, the National Institute for Occupational Safety and Health identified two shoe manufacturing facilities where workers experienced relatively "pure" exposures to toluene. A mortality study was conducted through December 31, 1982. An original study did not detect elevated leukemia mortality but did detect increased lung cancer mortality. The present study is an update of the mortality of the original cohort. The study cohort consisted of workers employed 1 month or more between 1940 and 1979 at two Ohio shoe manufacturing plants. Vital status was ascertained through December 31, 1999. Seven thousand eight hundred twenty eight workers, contributing 300,777 person years, were available for analysis. An excess of lung cancer deaths persisted with additional years of follow-up (SMR = 1.36, 95% confidence interval (CI) = 1.19-1.54). Trend tests did not indicate a positive trend between lung cancer risk and duration of employment. Mortality from leukemia was not significantly elevated in the updated analysis. Results indicate a possible association between lung cancer mortality and exposure to chronic, low-levels of organic solvents. Although the strength of this conclusion was weakened by the lack of increasing lung cancer risk in relation to duration of employment, other studies have supported this association. Published 2006 Wiley-Liss, Inc.

Grain-filling duration and grain yield relationships in wheat mutants

International Nuclear Information System (INIS)

Larik, A.S.

1987-01-01

Nine stable mutants of bread wheat along with their mother cultivars were investigated for grain-filling characteristics in relation to grain yield. Significant differences among mutants for grain-filling duration and grain-filling index were observed. Inspite of the consistent differences in grain-filling duration there was no significant association between grain-filling duration and grain yield in C-591 and Nayab mutants. Failure to detect an yield advantage due to differences in grain-filling duration in these genotypes suggests that any advantage derived from alteration of grain-filling period may have been outweighed by the coincident changes in length of the vegetative period. Other factors such as synchrony of anthesis may have limited out ability to find an association between grainfilling duration and grain yield. On the contrary, significant association between grain-filling duration and grain yield displayed by indus-66 indus-66 mutants derived from gamma rays, shows the ability of gamma rays to induce functional alternations in the pattern of gene arrangements controlling these traits. Thus, the vaability observed in these physiological traits suggests that selection for these traits could be useful in improving grain yield. (author)

How Rice (Oryza sativa L.) Responds to Elevated As under Different Si-Rich Soil Amendments.

Science.gov (United States)

Teasley, William A; Limmer, Matthew A; Seyfferth, Angelia L

2017-09-19

Several strategies exist to mitigate As impacts on rice and each has its set of trade-offs with respect to yield, inorganic As content in grain, and CH 4 emissions. The addition of Si to paddy soil can decrease As uptake by rice but how rice will respond to elevated As when soil is amended with Si-rich materials is unresolved. Here, we evaluated yield impacts and grain As content and speciation in rice exposed to elevated As in response to different Si-rich soil amendments including rice husk, rice husk ash, and CaSiO 3 in a pot study. We found that As-induced yield losses were alleviated by Husk amendment, partially alleviated by Ash amendment, and not affected by CaSiO 3 amendment. Furthermore, Husk was the only tested Si-amendment to significantly decrease grain As concentrations. Husk amendment was likely effective at decreasing grain As and improving yield because it provided more plant-available Si, particularly during the reproductive and ripening phases. Both Husk and Ash provided K, which also played a role in yield improvement. This study demonstrates that while Si-rich amendments can affect rice uptake of As, the kinetics of Si dissolution and nutrient availability can also affect As uptake and toxicity in rice.

Mortality among plutonium and other workers at a nuclear facility

International Nuclear Information System (INIS)

Wilkinson, G.S.; Voelz, G.L.; Acquavella, J.F.; Tietjen, G.L.; Reyes, M.; Brackbill, R.; Wiggs, L.

1983-01-01

Mortality among plutonium and other nuclear workers has been investigated to assess the effects of exposures to low levels of internal and external radiation. Standarized mortality ratios (SMRs) for white male workers employed at least two years from 1951 through 1977 were significantly lower than expected for all causes, all cancers, cancers of the respiratory system, and lung cancer. Benign neoplasms, all of which were intracranial tumors, were significantly elevated. No bone cancers were discovered and other radiogenic cancers did not differ significantly from expectation. Duration of employment and latency did not affect these results. SMRs for a subcohort of plutonium exposed workers were significantly low for all causes of deaths and all cancers. Estimates of relative risk for workers exposed to 2 or more nCi compared to unexposed workers were not significantly higher or lower than unity. These findings do not support the hypothesis of increased mortality among plutonium and other nuclear workers. The excess for benign and unspecified intracranial tumors is not consistent with previous studies on radiation induced brain tumors in terms of latency and exposure levels

Elevated Frequencies of Micronuclei and other Nuclear Abnormalities of Chrome Plating Workers Occupationally Exposed to Hexavalent Chromium.

Science.gov (United States)

Sudha, S; Kripa, S K; Shibily, P; Shyn, J

2011-01-01

Biomonitoring provides a useful tool to estimate the genetic risk from exposure to genotoxic agents. The aim of this study was to assess the potential cytogenetic damage associated with occupational exposure to hexavalent chromium by using micronuclei (MN) as a biomarker. This was a cross-sectional study and all participants were males. Both the exposed and control individuals were selected from Coimbatore, Southern India. Exfoliated buccal cells from 44 chrome plating workers and 40 age and sex matched control subjects were examined for MN frequency and nuclear abnormalities (NA) other than micronuclei, such as binucleates, broken eggs, karyorrhexis, karyolysis and pyknosis. Results showed statistically significant difference between chrome plating workers and control groups. MN and NA frequencies in chrome plating workers were significantly higher than those in control groups (p chrome plating workers are under risk of significant cytogenetic damage. Therefore, there is a need to educate those who work with heavy metals about the potential hazard of occupational exposure and the importance of using protective measures.

Malignant pleural mesothelioma risk among nuclear workers: a review

International Nuclear Information System (INIS)

Metz-Flamant, C; Guseva Canu, I; Laurier, D

2011-01-01

Exposure to ionising radiation has been suggested as a causal risk factor for malignant pleural mesothelioma (MPM). Studies of patients treated by radiotherapy for primary cancers have suggested that radiation contributes to the development of secondary MPM. Here we examined the risk to nuclear workers of MPM related to exposure to low doses of occupational radiation at low dose rates. All results concerning MPM risk in published studies of nuclear workers were examined for their association with radiation exposure and potential confounders. We found 19 relevant studies. Elevated risks of pleural cancer were reported in most (15/17) of these studies. Eight reported risks higher for radiation monitored workers than for other workers. However, of 12 studies that looked at associations with ionising radiation, only one reported a significant dose-risk association. Asbestos was an important confounder in most studies. We conclude that studies of nuclear workers have not detected an association between ionising radiation exposure and MPM. Further investigations should improve the consideration of asbestos exposure at the same time as they address the risk of MPM related to occupational exposure of nuclear workers to low doses of ionising radiation at low dose rates. (review)

Malignant pleural mesothelioma risk among nuclear workers: a review

Energy Technology Data Exchange (ETDEWEB)

Metz-Flamant, C; Guseva Canu, I; Laurier, D, E-mail: camille.metz@irsn.fr [Laboratory of Epidemiology, Institute of Radiological Protection and Nuclear Safety (IRSN), Fontenay-aux-Roses (France)

2011-03-01

Exposure to ionising radiation has been suggested as a causal risk factor for malignant pleural mesothelioma (MPM). Studies of patients treated by radiotherapy for primary cancers have suggested that radiation contributes to the development of secondary MPM. Here we examined the risk to nuclear workers of MPM related to exposure to low doses of occupational radiation at low dose rates. All results concerning MPM risk in published studies of nuclear workers were examined for their association with radiation exposure and potential confounders. We found 19 relevant studies. Elevated risks of pleural cancer were reported in most (15/17) of these studies. Eight reported risks higher for radiation monitored workers than for other workers. However, of 12 studies that looked at associations with ionising radiation, only one reported a significant dose-risk association. Asbestos was an important confounder in most studies. We conclude that studies of nuclear workers have not detected an association between ionising radiation exposure and MPM. Further investigations should improve the consideration of asbestos exposure at the same time as they address the risk of MPM related to occupational exposure of nuclear workers to low doses of ionising radiation at low dose rates. (review)

AUTOMATION OF TRACEABILITY PROCESS AT GRAIN TERMINAL LLC “ UKRTRANSAGRO"

Directory of Open Access Journals (Sweden)

F. A. TRISHYN

2017-07-01

Full Text Available A positive trend of growth in both grain production and export is indicated. In the current marketing year the export potential of the Ukrainian grain market is close to the record level. However, the high positions in the rating of world exporters are achieved not only due to the high export potential, but also because of higher quality and logistics. These factors depend directly on the quality of enterprise management and all processes occurring at it. One of the perspective ways of enterprise development is the implementation of the traceability system and further automation of the traceability process. European integration laws are obliging Ukrainian enterprises to have a traceability system. Traceability is an ability to follow the movement of a feed or food through specified stages of production, processing and distribution. The process of traceability is managing by people, which implies a human factor. Automation will allow, in a greater extent, to exclude the human factor that will mean decreasing of errors in documentation and will speed up the process of grain transshipment. Research work on the process was carried out on the most modern grain terminal - LLC “UkrTransAgro”. The terminal is located in the Ukrainian water area of the Azov Sea (Mariupol, Ukraine. Characteristics of the terminal: capacity of a simultaneous storage - 48,120 thousand tons, acceptance of crops from transport - 4,500 tons / day; acceptance of crops from railway transport - 3000 tons / day, transshipment capacity - up to 1.2 million tons per year, shipment to the sea vessels - 7000 tons / day. The analysis of the automation level of the grain terminal is carried out. The company uses software from 1C - «1C: Enterprise 8. Accounting for grain elevator, mill, and feed mill for Ukraine». This software is used for quantitative and qualitative registration at the elevator in accordance with industry guidelines and standards. The software product has many

Giant grains

International Nuclear Information System (INIS)

Leitch-Devlin, M.A.; Millar, T.J.; Williams, D.A.

1976-01-01

Infrared observations of the Orion nebula have been interpreted by Rowan-Robinson (1975) to imply the existence of 'giant' grains, radius approximately 10 -2 cm, throughout a volume about a parsec in diameter. Although Rowan-Robinson's model of the nebula has been criticized and the presence of such grains in Orion is disputed, the proposition is accepted, that they exist, and in this paper situations in which giant grains could arise are examined. It is found that, while a giant-grain component to the interstellar grain density may exist, it is difficult to understand how giant grains arise to the extent apparently required by the Orion nebula model. (Auth.)

Study on Strengthening and Toughening Mechanisms of Aluminum Alloy 2618-Ti at Elevated Temperature

Science.gov (United States)

Kun, Ma; Tingting, Liu; Ya, Liu; Xuping, Su; Jianhua, Wang

2018-01-01

The tensile properties of the alloy 2618 and 2618-Ti were tested using a tensile testing machine. The morphologies of the fracture of tensile samples were observed using scanning electron microscopy. The strengthening and toughening mechanisms of alloy 2618-Ti at elevated temperature were systematically investigated based on the analyses of experimental results. The results showed that the tensile strength of alloy 2618-Ti is much higher than that of alloy 2618 at the temperature range of 250 and 300 °C. But the elongation of alloy 2618-Ti is much higher than that of alloy 2618 at the temperature range of 200 and 300 °C. The equal-strength temperature of intragranular and grain boundary of alloy 2618-Ti is about 235 °C. When the temperature is lower than 235 °C, the strengthening of alloy 2618-Ti is ascribed to the strengthening effect of fine grains and dispersed Al3Ti/Al18Mg3Ti2 phase. When the temperature is higher than 235 °C, the strengthening effect of alloy 2618-Ti is mainly attributed to the load transfer of Al3Ti and Al18Mg3Ti2 particles. The toughening of alloy 2618-Ti at elevated temperature is mainly ascribed to the fine grain microstructure, excellent combination between matrix and dispersed Al3Ti/Al18Mg3Ti2 particles as well as the recrystallization of the alloy at elevated temperature.

Information, Technology and Information Worker Productivity: Task Level Evidence

OpenAIRE

Sinan Aral; Erik Brynjolfsson; Marshall Van Alstyne

2007-01-01

In an effort to reveal the fine-grained relationships between IT use, patterns of information flows, and individual information-worker productivity, we study task level practices at a midsize executive recruiting firm. We analyze both project-level and individual-level performance using: (1) detailed accounting data on revenues, compensation, project completion rates, and team membership for over 1300 projects spanning 5 years, (2) direct observation of over 125,000 email messages over a peri...

Lung Cancer Mortality among Uranium Gaseous Diffusion Plant Workers: A Cohort Study 1952–2004

Directory of Open Access Journals (Sweden)

LW Figgs

2013-07-01

Full Text Available Background: 9%–15% of all lung cancers are attributable to occupational exposures. Reports are disparate regarding elevated lung cancer mortality risk among workers employed at uranium gaseous diffusion plants. Objective: To investigate whether external radiation exposure is associated with lung cancer mortality risk among uranium gaseous diffusion workers. Methods: A cohort of 6820 nuclear industry workers employed from 1952 to 2003 at the Paducah uranium gaseous diffusion plant (PGDP was assembled. A job-specific exposure matrix (JEM was used to determine likely toxic metal exposure categories. In addition, radiation film badge dosimeters were used to monitor cumulative external ionizing radiation exposure. International Classification for Disease (ICD codes 9 and 10 were used to identify 147 lung cancer deaths. Logistic and proportional hazards regression were used to estimate lung cancer mortality risk. Results: Lung cancer mortality risk was elevated among workers who experienced external radiation >3.5 mrem and employment duration >12 years. Conclusion: Employees of uranium gaseous diffusion plants carry a higher risk of lung cancer mortality; the mortality is associated with increased radiation exposure and duration of employment.

[Response of rice grain quality traits to free-air CO2 enrichment].

Science.gov (United States)

Dong, Guichun; Wang, Yulong; Huang, Jianye; Yang, Hongjian; Gu, Hui; Peng, Bin; Ju, Jing; Yang, Lianxin; Zhu, Jianguo; Shan, Yuhua

2004-07-01

The study showed that under field condition, when the CO2 concentration was elevated 200 micromol x mol(-1) above control, the average brown rice rate of japonica variety Wuxiangjing 14 was 1.4% higher, while lead milled rice rate was 12.3% lower than control. The brown rice rate increased at lower nitrogen supply level (LN), while lead milled rice rate increased at higher nitrogen supply level (HN). The percentage of chalky grain was 11.9% higher, and chalkiness degree was 2.8% higher than control, but no obvious difference was found in chalkiness area between the FACE and the control. The chalkiness area, percentage of chalky grain and chalkiness degree decreased at HN plus higher phosphorus supply level (HP). The gelatinization temperature was elevated 0.52 degrees C, gel consistency increased, while amylose content was not statistically significant. The amylose content decreased at HN plus HP, while gel consistency and gelatinization temperature decreased at LN plus HP and at LN, respectively. The protein content was decreased 0.6% under FACE treatment and at LN plus lower phosphorus supply level.

Identification of environmentally derived cesium-137 burdens in a worker population

International Nuclear Information System (INIS)

MacLellan, J.A.; Lynch, T.P.; Rieksts, G.A.; Brodzinski, R.L.

1993-01-01

During 1990, whole body measurements of a number of workers with little probability of onsite occupational exposure showed positive evidence of 137 Cs. Further investigation revealed that many of these workers supplemented their diet with a significant portion of wild game, mainly deer and elk. To validate the assumption of an environmental source, donated samples of venison and other game were analyzed by gamma spectroscopy. Results ranged from less than 0.1 to almost 100 Bq kg -l (0.003 to 2.7 nCi kg -1 ) and showed a correlation with the habitat from which the game was taken. Venison samples obtained from the two workers with the highest body burdens showed the highest activity. A questionnaire is now used to identify workers with an elevated potential for environmental-intakes

Carpel size, grain filling, and morphology determine individual grain weight in wheat.

Science.gov (United States)

Xie, Quan; Mayes, Sean; Sparkes, Debbie L

2015-11-01

Individual grain weight is a major yield component in wheat. To provide a comprehensive understanding of grain weight determination, the carpel size at anthesis, grain dry matter accumulation, grain water uptake and loss, grain morphological expansion, and final grain weight at different positions within spikelets were investigated in a recombinant inbred line mapping population of bread wheat (Triticum aestivum L.)×spelt (Triticum spelta L.). Carpel size, grain dry matter and water accumulation, and grain dimensions interacted strongly with each other. Furthermore, larger carpels, a faster grain filling rate, earlier and longer grain filling, more grain water, faster grain water absorption and loss rates, and larger grain dimensions were associated with higher grain weight. Frequent quantitative trait locus (QTL) coincidences between these traits were observed, particularly those on chromosomes 2A, 3B, 4A, 5A, 5DL, and 7B, each of which harboured 16-49 QTLs associated with >12 traits. Analysis of the allelic effects of coincident QTLs confirmed their physiological relationships, indicating that the complex but orderly grain filling processes result mainly from pleiotropy or the tight linkages of functionally related genes. After grain filling, distal grains within spikelets were smaller than basal grains, primarily due to later grain filling and a slower initial grain filling rate, followed by synchronous maturation among different grains. Distal grain weight was improved by increased assimilate availability from anthesis. These findings provide deeper insight into grain weight determination in wheat, and the high level of QTL coincidences allows simultaneous improvement of multiple grain filling traits in breeding. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Cancer risk analysis among medical diagnostic X-ray workers in China

International Nuclear Information System (INIS)

Wang Jixian; Li Benxiao; Gao Zhiwei; Xu Jun; Zhang Jingyuan; Aoyama, Takashi; Sugahara, Tsutomu

1997-01-01

To provide the evidence and related rules of human malignant tumors produced by prolonged exposure to low level ionizing radiation. The cancer incidence (1950-1990) among 27011 medical diagnostic X-ray workers was compared with that among 25782 other medical specialists employed between 1950 and 1980 in China by means of O/E system. A significantly elevated risk of cancer was seen among diagnostic x-ray workers (RR = 1.1,95%Cl:1.0-1.2,P <0.05). Significantly elevated risks were seen for leukemia and cancers of skin, female breast, liver and esophagus, the RR being 2.3, 5.0, 1.6, 1.3 and 4.4 respectively. The RR for leukemia was higher for X-ray workers who began employment before 1970 and also for those who were young when employment began. The patterns of risk associated with length of service and with age and calendar year of initial employment suggest that the excesses of leukemia, skin cancer and female breast cancer were due to occupational exposure to X-rays. The ERR and EAR for leukemia and solid cancer were calculated roughly. (author)

Cancer incidence among Minnesota taconite mining industry workers.

Science.gov (United States)

Allen, Elizabeth M; Alexander, Bruce H; MacLehose, Richard F; Nelson, Heather H; Ramachandran, Gurumurthy; Mandel, Jeffrey H

2015-11-01

To evaluate cancer incidence among Minnesota taconite mining workers. We evaluated cancer incidence between 1988 and 2010 in a cohort of 40,720 Minnesota taconite mining workers used between 1937 and 1983. Standardized incidence ratios (SIRs) with 95% confidence intervals (CIs) were estimated by comparing numbers of incident cancers with frequencies in the Minnesota Cancer Surveillance System. SIRs for lung cancer by histologic subtypes were also estimated. We adjusted for out-of-state migration and conducted a probabilistic bias analysis for smoking-related cancers. A total of 5700 cancers were identified, including 51 mesotheliomas and 973 lung cancers. The SIRs for lung cancer and mesothelioma were 1.3 (95% CI = 1.2-1.4) and 2.4 (95% CI = 1.8-3.2), respectively. Stomach, laryngeal, and bladder cancers were also elevated. However, adjusting for potential confounding by smoking attenuated the estimates for lung (SIR = 1.1, 95% CI = 1.0-1.3), laryngeal (SIR = 1.2, 95% CI = 0.8-1.6), oral (SIR = 0.9, 95% CI = 0.7-1.2), and bladder cancers (SIR = 1.0, 95% CI = 0.8-1.1). Taconite workers may have an increased risk for certain cancers. Lifestyle and work-related factors may play a role in elevated morbidity. The extent to which mining-related exposures contribute to disease burden is being investigated. Copyright © 2015 Elsevier Inc. All rights reserved.

Fifty years of plutonium exposure to the Manhattan Project plutonium workers: an update.

Science.gov (United States)

Voelz, G L; Lawrence, J N; Johnson, E R

1997-10-01

Twenty-six white male workers who did the original plutonium research and development work at Los Alamos have been examined periodically over the past 50 y to identify possible health effects from internal plutonium depositions. Their effective doses range from 0.1 to 7.2 Sv with a median value of 1.25 Sv. As of the end of 1994, 7 individuals have died compared with an expected 16 deaths based on mortality rates of U.S. white males in the general population. The standardized mortality ratio (SMR) is 0.43. When compared with 876 unexposed Los Alamos workers of the same period, the plutonium worker's mortality rate was also not elevated (SMR = 0.77). The 19 living persons have diseases and physical changes characteristic of a male population with a median age of 72 y (range = 69 to 86 y). Eight of the twenty-six workers have been diagnosed as having one or more cancers, which is within the expected range. The underlying cause of death in three of the seven deceased persons was from cancer, namely cancer of prostate, lung, and bone. Mortality from all cancers was not statistically elevated. The effective doses from plutonium to these individuals are compared with current radiation protection guidelines.

Injurious effects of wool and grain dusts on alveolar epithelial cells and macrophages in vitro.

Science.gov (United States)

Brown, D M; Donaldson, K

1991-01-01

Epidemiological studies of workers in wool textile mills have shown a direct relation between the concentration of wool dust in the air and respiratory symptoms. Injurious effects of wool dust on the bronchial epithelium could be important in causing inflammation and irritation. A pulmonary epithelial cell line in vitro was therefore used to study the toxic effects of wool dust. Cells of the A549 epithelial cell line were labelled with 51Cr and treated with whole wool dusts and extracts of wool, after which injury was assessed. Also, the effects of grain dust, which also causes a form of airway obstruction, were studied. The epithelial injury was assessed by measuring 51Cr release from cells as an indication of lysis, and by monitoring cells which had detached from the substratum. No significant injury to A549 cells was caused by culture with any of the dusts collected from the air but surface "ledge" dust caused significant lysis at some doses. Quartz, used as a toxic control dust, caused significant lysis at the highest concentration of 100 micrograms/well. To determine whether any injurious material was soluble the dusts were incubated in saline and extracts collected. No extracts caused significant injury to epithelial cells. A similar lack of toxicity was found when 51Cr labelled control alveolar macrophages were targets for injury. Significant release of radiolabel was evident when macrophages were exposed to quartz at concentrations of 10 and 20 micrograms/well, there being no significant injury with either wool or grain dusts. These data suggest that neither wool nor grain dust produce direct injury to epithelial cells, and further studies are necessary to explain inflammation leading to respiratory symptoms in wool and grain workers. PMID:2015211

Toxicity and oxidative stress induced by chromium in workers exposed from different occupational settings around the globe: A review.

Science.gov (United States)

Junaid, Muhammad; Hashmi, Muhammad Zaffar; Malik, Riffat Naseem; Pei, De-Sheng

2016-10-01

The present review focused on the levels and toxicological status of heavy metals especially chromium (Cr) in the exposed workers from different occupational settings around the globe and in Pakistan. It was found that exposed workers from leather tanning and metal plating units showed elevated levels of Cr than the workers from other occupational settings. Cr and other heavy metals level in biological matrices of the exposed workers in different occupational settings revealed that developing countries are severely contaminated. Occupational settings from the Sialkot district, Pakistan exhibited elevated level of Cr in biological entities of the exposed workers. Review suggested that higher level of Cr exposure to the workers enhance the oxidative stress (reactive oxygen species (ROS) and hydroxyl (OH) radical generation) which may cause; cellular and molecular damage such as genotoxicity and chromosomal aberration formations, and carcinogenic effects. This review will help to understand the Cr contamination mechanisms and associated health implications in different occupational settings around the globe in general and particularly to Pakistan. This study will also assist occupational health and safety management authorities to devise or change the Cr recommended exposure limits (REL) for different occupational settings.

On the determination of the carrier concentration in large-grain polycrystalline InP, GaAs, and GaP by Hall effect measurements

International Nuclear Information System (INIS)

Siegel, W.; Kuehnel, G.; Schneider, H.A.

1985-01-01

Hall and conductivity measurements are performed in a wide temperature region on large-grain polycrystalline samples of n-InP, n- and p-GaAs as well as n- and p-GaP. The feasibility of Hall measurements at a given temperature depends mainly on the height PHI/sub B/ of the grain boundary potential barriers and on the average grain size. Measurements at room temperature are possible on large-grain material (average grain size 0.2 to 1 mm) for PHI/sub B/ <= 0.4 eV. For greater barrier heights elevated temperatures are necessary. If the Hall coefficient is measurable than it yields an effective carrier concentration for the polycrystalline sample which agrees well with the carrier concentration in the bulk of the grains. (author)

Development of a safety decision-making scenario to measure worker safety in agriculture.

Science.gov (United States)

Mosher, G A; Keren, N; Freeman, S A; Hurburgh, C R

2014-04-01

Human factors play an important role in the management of occupational safety, especially in high-hazard workplaces such as commercial grain-handling facilities. Employee decision-making patterns represent an essential component of the safety system within a work environment. This research describes the process used to create a safety decision-making scenario to measure the process that grain-handling employees used to make choices in a safety-related work task. A sample of 160 employees completed safety decision-making simulations based on a hypothetical but realistic scenario in a grain-handling environment. Their choices and the information they used to make their choices were recorded. Although the employees emphasized safety information in their decision-making process, not all of their choices were safe choices. Factors influencing their choices are discussed, and implications for industry, management, and workers are shared.

Abnormal grain growth: a non-equilibrium thermodynamic model for multi-grain binary systems

International Nuclear Information System (INIS)

Svoboda, J; Fischer, F D

2014-01-01

Abnormal grain growth as the abrupt growth of a group of the largest grains in a multi-grain system is treated within the context of unequal retardation of grain growth due to the segregation of solute atoms from the bulk of the grains into the grain boundaries. During grain boundary migration, the segregated solute atoms are dragged under a small driving force or left behind the migrating grain boundary under a large driving force. Thus, the solute atoms in the grain boundaries of large grains, exhibiting a large driving force, can be released from the grain boundary. The mobility of these grain boundaries becomes significantly higher and abnormal grain growth is spontaneously provoked. The mean-field model presented here assumes that each grain is described by its grain radius and by its individual segregation parameter. The thermodynamic extremal principle is engaged to obtain explicit evolution equations for the radius and segregation parameter of each grain. Simulations of grain growth kinetics for various conditions of segregation with the same initial setting (100 000 grains with a given radius distribution) are presented. Depending on the diffusion coefficients of the solute in the grain boundaries, abnormal grain growth may be strongly or marginally pronounced. Solute segregation and drag can also significantly contribute to the stabilization of the grain structure. Qualitative agreement with several experimental results is reported. (paper)

Concentration contours in lattics and grain boundary diffusion in a polycrystalline solid

International Nuclear Information System (INIS)

Kim, Yong Soo; Jae, Won Mok; El Saied, Usama; Olander, Donald R.

1995-01-01

Grain boundary diffusion plays significant role in the fission gas release, which is one of the crucial processes dominating nuclear fuel performance. Gaseous fission products such as Xe and Kr generated inside fuel pellet have to diffuse in the lattice and in the grain boundary before they reach open space in the fuel rod. In the mean time, the grains in the fuel pellet grow and shrink according to grain growth kinetics, especially at elevated temperature at which nuclear reactors are operating. Thus the boundary movement ascribed to the grain growth greatly influences the fission gas release rate by lengthening or shortening the lattice diffusion distance, which is the rate limiting step. Sweeping fission gases by the moving boundary contributes to the increment of the fission gas release as well. Lattice and grain boundary diffusion processes in the fission gas release can be studied by 'tracer diffusion' technique, by which grain boundary diffusivity can be estimated and used directly for low burn up fission gas release analysis. However, even for tracer diffusion analysis, taking both the intragranular grain growth and the diffusion processes simultaneously into consideration is not easy. Only a few models accounting for the both processes are available and mostly handle them numerically. Numerical solutions are limited in the practical use. Here in this paper, an approximate analytical solution of the lattice and stationary grain boundary diffusion in a polycrystalline solid is developed for the tracer diffusion techniques. This short closed form solution is compared to available exact and numerical solutions and turns out to be acceptably accurate. It can be applied to the theoretical modeling and the experimental analysis, especially PIE (post irradiation examination), of low burn up fission gas release

Elevated liver enzymes in women with a family history of diabetes.

Science.gov (United States)

Inoue, Kazuo; Matsumoto, Masatoshi; Miyoshi, Yuji; Kobayashi, Yasuki

2008-03-01

Both elevated liver enzymes and a family history of diabetes mellitus (FHDM) are independent risk factors for type 2 diabetes. This study evaluates the epidemiological association between elevated liver enzymes and FHDM. Subjects included 3512 women workers without diabetes, hepatitis, a smoking habit, or a history of alcohol intake. Blood samples and personal data were collected from all subjects. Subjects with FHDM had a higher mean body mass index (BMI: 23.9kg/m(2) vs. 23.4kg/m(2); p=0.003). Laboratory testing also revealed higher mean fasting plasma glucose (FPG: 5.67mmol/L vs. 5.22mmol/L; penzymes were associated with FHDM. In particular, elevated GGT was related to FHDM, independent of the other variables. Elevated liver enzymes, probably due to fat deposition in the liver, may play a role in increasing the risk of diabetes in individuals with FHDM.

Exposure to field vs. storage wheat dust: different consequences on respiratory symptoms and immune response among grain workers.

Science.gov (United States)

Barrera, Coralie; Wild, Pascal; Dorribo, Victor; Savova-Bianchi, Dessislava; Laboissière, Audrey; Pralong, Jacques A; Danuser, Brigitta; Krief, Peggy; Millon, Laurence; Reboux, Gabriel; Niculita-Hirzel, Hélène

2018-05-26

The aim of this study was to understand the differential acute effects of two distinct wheat-related dusts, such as field or stored wheat dust handling, on workers' health and how those effects evolved at 6 month intervals. Exposure, work-related symptoms, changes in lung function, and blood samples of 81 workers handling wheat and 61 controls were collected during the high exposure season and 6 months after. Specific IgG, IgE, and precipitins against 12 fungi isolated from wheat dust were titrated by enzyme-linked immunosorbent assay, dissociation-enhanced lanthanide fluorescence immunoassay, and electrosyneresis. The level of fungi was determined in the workers' environment. Levels of exhaled fraction of nitrogen monoxide (F E NO) and total IgE were obtained. Exposure response associations were investigated by mixed logistic and linear regression models. The recent exposure to field wheat dust was associated with a higher prevalence for five of six self-reported airway symptoms and with a lower F E NO than those in the control population. Exposure to stored wheat dust was only associated with cough. No acute impact of exposure on respiratory function was observed. Exposure to field wheat dust led to workers' sensitization against the three field fungi Aureobasidum, Cryptococcus, and Phoma, although exposure to storage wheat dust was associated with tolerance. The level of Ig remained stable 6 months after exposure. The clinical picture of workers exposed to field or storage wheat dust differed. The systematic characterization of the aerosol microbial profile may help to understand the reasons for those differences.

Analysis of the Effect of Prevailing Weather Conditions on the Occurrence of Grain Dust Explosions.

Science.gov (United States)

Sanghi, Achint; Ambrose, R P Kingsly

2016-07-27

Grain dust explosions have been occurring in the U.S. for the past twenty years. In the past ten years, there have been an average of ten explosions a year, resulting in nine fatalities and 93 injuries. In more than half of these cases, the ignition source remains unidentified. The effect of ambient humidity on the likelihood of a dust explosion has been discussed for many years. However, no investigation into a possible link between the two has been carried out. In this study, we analyzed local weather data and grain dust explosions during the period 2006 to 2014 to measure potential relationships between the two events. The 84 analyzed explosions do not show any trend with regard to prevailing temperatures, or relative or absolute humidity. In addition, the ignition source could not be identified in 54 of the incidents. The majority of grain dust explosion incidents occurred at grain elevator facilities, where the dust generation potential was high compared with grain processing industries. Copyright© by the American Society of Agricultural Engineers.

Factors associated with non-participation and drop-out in a lifestyle intervention for workers with an elevated risk of cardiovascular disease

Directory of Open Access Journals (Sweden)

van der Beek Allard J

2009-12-01

Full Text Available Abstract Background Non-response and drop-out are problems that are commonly encountered in health promotion trials. Understanding the health-related characteristics of non-participants and drop-outs and the reasons for non-participation and drop-out may be beneficial for future intervention trials. Methods Male construction workers with an elevated risk of cardiovascular disease (CVD were invited to participate in a lifestyle intervention study. In order to investigate the associations between participation and CVD risk factors, and drop-out and CVD risk factors, crude and multiple logistic regression analyses were performed. The reasons for non-participation and drop-out were assessed qualitatively. Results 20% of the workers who were invited decided to participate; 8.6% of the participants dropped out before the first follow-up measurement. The main reasons for non-participation were 'no interest', 'current (para-medical treatment', and 'feeling healthy', and for drop-out they were 'lack of motivation', 'current (para-medical treatment', and 'disappointment'. Participants were 4.2 years older, had a higher blood pressure, higher total cholesterol, and lower HDL cholesterol than non-participants, and were more likely to report 'tiredness and/or stress' and 'chest pain and/or shortness of breath'. After adjusting for age, most risk factors were not significantly associated with participation. Drop-outs were 4.6 years younger than those who completed the study. The prevalence of smoking was higher among non-participants and drop-outs. Conclusion Participants had a worse CVD risk profile than non-participants, mainly because of the difference in age. Non-participants and drop-outs were younger and more likely to be smokers. The main reasons for non-participation and drop-out were health-related. Investigators in the field of health promotion should be encouraged to share comparable information. Trial registration Current Controlled Trials ISRCTN

A grain-boundary diffusion model of dynamic grain growth during superplastic deformation

International Nuclear Information System (INIS)

Kim, Byung-Nam; Hiraga, Keijiro; Sakka, Yoshio; Ahn, Byung-Wook

1999-01-01

Dynamic grain growth during superplastic deformation is modelled on the basis of a grain-boundary diffusion mechanism. On the grain boundary where a static and a dynamic potential difference coexist, matter transport along the boundary is assumed to contribute to dynamic grain growth through depositing the matter on the grain surface located opposite to the direction of grain-boundary migration. The amount of the diffusive matter during deformation is calculated for an aggregate of spherical grains and is converted to the increment of mean boundary migration velocity. The obtained relationship between the strain rate and the dynamic grain growth rate is shown to be independent of deformation mechanisms, provided that the grain growth is controlled by grain-boundary diffusion. The strain dependence, strain-rate dependence and temperature dependence of grain growth predicted from this model are consistent with those observed in superplastic ZrO 2 -dispersed Al 2 O 3

Carpel size, grain filling, and morphology determine individual grain weight in wheat

OpenAIRE

Xie, Quan; Mayes, Sean; Sparkes, Debbie L.

2015-01-01

Individual grain weight is a major yield component in wheat. To provide a comprehensive understanding of grain weight determination, the carpel size at anthesis, grain dry matter accumulation, grain water uptake and loss, grain morphological expansion, and final grain weight at different positions within spikelets were investigated in a recombinant inbred line mapping population of bread wheat (Triticum aestivum L.)?spelt (Triticum spelta L.). Carpel size, grain dry matter and water accumulat...

An updated historical cohort mortality study of workers exposed to asbestos in a refitting shipyard, 1947-2007.

Science.gov (United States)

Tomioka, Kimiko; Natori, Yuji; Kumagai, Shinji; Kurumatani, Norio

2011-12-01

To evaluate the long-term health effects of occupational asbestos exposure, an updated historical cohort mortality study of workers at a refitting shipyard was undertaken. The cohort consisted of 249 male ship repair workers (90 laggers, 159 boiler repairers). To determine relative excess mortality, standardized mortality ratios (SMRs) were calculated using mortality rates among the Japanese male population. Mortality follow-up of study subjects was performed for the period from 1947 till the end of 2007. We identified the vital status of 87 (96.7%) laggers and 150 (94.3%) boiler repairers. Of these, 63 (72.4%) and 95 (63.3%), respectively, died. Laggers, who had handled asbestos materials directly, showed a significantly elevated SMR of 2.64 (95% confidence interval [CI]: 1.06-5.44) for lung cancer and 2.49 (95% CI: 1.36-4.18) for nonmalignant respiratory diseases. Boiler repairers, who had many opportunities for secondary exposure to asbestos and a few for direct exposure, showed no significant elevation in SMR for lung cancer but a significantly elevated SMR of 1.78 (95% CI: 1.06-2.81) for nonmalignant respiratory diseases. In an analysis according to duration of employment, there was a significantly elevated SMR of nonmalignant respiratory diseases in the longer working years group. Among workers from both jobs, no deaths caused by mesothelioma in addition to those in the original study were found and no subject died from larynx cancer. This updated study confirmed a significant excess of asbestos-related mortality from diseases such as lung cancer and nonmalignant respiratory diseases among workers in a refitting shipyard in Japan.

Viscoelastic sliding and diffusive relaxation along grain boundaries in polycrystalline boron nitride

International Nuclear Information System (INIS)

Pezzotti, G.; Nishida, Toshihiko; Kleebe, H.J.; Ota, Kenichi

1997-01-01

Dense hexagonal boron nitride (BN) materials were prepared via two different processing routes: (1) hot-pressing with the addition of a Ca/B-containing glass and (2) chemical vapor deposition (CVD). The resulting microstructure of both materials was studied by scanning and transmission electron microscopy. While the hot-pressed BN material shows, apart from large BN matrix grains, an inhomogeneous distribution of residual glass at room temperature, the CVD deposition yields a homogeneous fine grained microstructure with no amorphous residue detectable. Internal-friction experiments were performed to study the micromechanical response of the materials when exposed to high temperatures. The CVD material revealed no relaxation peak during testing up to 2,300 C, while the glass-doped sample showed a pronounced relaxation peak at a peak-top temperature of about 600 C. This temperature corresponds to the softening temperature known for bulk Ca/B-glasses and it is, therefore, concluded that the glass homogeneously wets the BN grains at elevated temperatures. The results presented are seen as the first clear evidence that the internal friction peak monitored for various glass-containing ceramics is indeed related to a viscous sliding process along grain boundaries

Effect of elevated [CO2] and nutrient management on wet and dry season rice production in subtropical India

Institute of Scientific and Technical Information of China (English)

Sushree Sagarika Satapathy; Dillip Kumar Swain; Surendranath Pasupalak; Pratap Bhanu Singh Bhadoria

2015-01-01

The present experiment was conducted to evaluate the effect of elevated [CO2] with varying nutrient management on rice–rice production system. The experiment was conducted in the open field and inside open-top chambers（OTCs） of ambient [CO2]（≈ 390 μmol L-1） and elevated [CO2] environment（25% above ambient） during wet and dry seasons in 2011–2013at Kharagpur, India. The nutrient management included recommended doses of N, P, and K as chemical fertilizer（CF）, integration of chemical and organic sources, and application of increased（25% higher） doses of CF. The higher [CO2] level in the OTC increased aboveground biomass but marginally decreased filled grains per panicle and grain yield of rice, compared to the ambient environment. However, crop root biomass was increased significantly under elevated [CO2]. With respect to nutrient management, increasing the dose of CF increased grain yield significantly in both seasons. At the recommended dose of nutrients, integrated nutrient management was comparable to CF in the wet season, but significantly inferior in the dry season, in its effect on growth and yield of rice. The [CO2] elevation in OTC led to a marginal increase in organic C and available P content of soil, but a decrease in available N content. It was concluded that increased doses of nutrients via integration of chemical and organic sources in the wet season and chemical sources alone in the dry season will minimize the adverse effect of future climate on rice production in subtropical India.

Effect of elevated [CO2] and nutrient management on wet and dry season rice production in subtropical India

Institute of Scientific and Technical Information of China (English)

Sushree Sagarika Satapathy; Dillip Kumar Swain; Surendranath Pasupalak; Pratap Bhanu Singh Bhadoria

2015-01-01

The present experiment was conducted to evaluate the effect of elevated [CO2] with varying nutrient management on rice–rice production system. The experiment was conducted in the open field and inside open-top chambers (OTCs) of ambient [CO2] (≈390μmol L−1) and elevated [CO2] environment (25%above ambient) during wet and dry seasons in 2011–2013 at Kharagpur, India. The nutrient management included recommended doses of N, P, and K as chemical fertilizer (CF), integration of chemical and organic sources, and application of increased (25%higher) doses of CF. The higher [CO2] level in the OTC increased aboveground biomass but marginally decreased filled grains per panicle and grain yield of rice, compared to the ambient environment. However, crop root biomass was increased significantly under elevated [CO2]. With respect to nutrient management, increasing the dose of CF increased grain yield significantly in both seasons. At the recommended dose of nutrients, integrated nutrient management was comparable to CF in the wet season, but significantly inferior in the dry season, in its effect on growth and yield of rice. The [CO2] elevation in OTC led to a marginal increase in organic C and available P content of soil, but a decrease in available N content. It was concluded that increased doses of nutrients via integration of chemical and organic sources in the wet season and chemical sources alone in the dry season will minimize the adverse effect of future climate on rice production in subtropical India.

Chromosome aberrations in the peripheral lymphocytes of thorium workers with low body burdens of 212Bi

International Nuclear Information System (INIS)

Hoegerman, S.F.

1976-01-01

Cytogenetic analysis of 8 thorium workers and 3 controls has not shown a significant elevation in the level of chromosome breakage in the workers' peripheral lymphocytes. This finding is consistent with an estimate of the amount of damage to be expected in these cases, based on the level of chromosome breakage observed in Thorotrast cases with measured 212 Bi burdens

Grain-resolved analysis of localized deformation in nickel-titanium wire under tensile load.

Science.gov (United States)

Sedmák, P; Pilch, J; Heller, L; Kopeček, J; Wright, J; Sedlák, P; Frost, M; Šittner, P

2016-08-05

The stress-induced martensitic transformation in tensioned nickel-titanium shape-memory alloys proceeds by propagation of macroscopic fronts of localized deformation. We used three-dimensional synchrotron x-ray diffraction to image at micrometer-scale resolution the grain-resolved elastic strains and stresses in austenite around one such front in a prestrained nickel-titanium wire. We found that the local stresses in austenite grains are modified ahead of the nose cone-shaped buried interface where the martensitic transformation begins. Elevated shear stresses at the cone interface explain why the martensitic transformation proceeds in a localized manner. We established the crossover from stresses in individual grains to a continuum macroscopic internal stress field in the wire and rationalized the experimentally observed internal stress field and the topology of the macroscopic front by means of finite element simulations of the localized deformation. Copyright © 2016, American Association for the Advancement of Science.

Grain dissection as a grain size reducing mechanism during ice microdynamics

Science.gov (United States)

Steinbach, Florian; Kuiper, Ernst N.; Eichler, Jan; Bons, Paul D.; Drury, Martin R.; Griera, Albert; Pennock, Gill M.; Weikusat, Ilka

2017-04-01

Ice sheets are valuable paleo-climate archives, but can lose their integrity by ice flow. An understanding of the microdynamic mechanisms controlling the flow of ice is essential when assessing climatic and environmental developments related to ice sheets and glaciers. For instance, the development of a consistent mechanistic grain size law would support larger scale ice flow models. Recent research made significant progress in numerically modelling deformation and recrystallisation mechanisms in the polycrystalline ice and ice-air aggregate (Llorens et al., 2016a,b; Steinbach et al., 2016). The numerical setup assumed grain size reduction is achieved by the progressive transformation of subgrain boundaries into new high angle grain boundaries splitting an existing grain. This mechanism is usually termed polygonisation. Analogue experiments suggested, that strain induced grain boundary migration can cause bulges to migrate through the whole of a grain separating one region of the grain from another (Jessell, 1986; Urai, 1987). This mechanism of grain dissection could provide an alternative grain size reducing mechanism, but has not yet been observed during ice microdynamics. In this contribution, we present results using an updated numerical approach allowing for grain dissection. The approach is based on coupling the full field theory crystal visco-plasticity code (VPFFT) of Lebensohn (2001) to the multi-process modelling platform Elle (Bons et al., 2008). VPFFT predicts the mechanical fields resulting from short strain increments, dynamic recrystallisation process are implemented in Elle. The novel approach includes improvements to allow for grain dissection, which was topologically impossible during earlier simulations. The simulations are supported by microstructural observations from NEEM (North Greenland Eemian Ice Drilling) ice core. Mappings of c-axis orientations using the automatic fabric analyser and full crystallographic orientations using electron

Factors influencing economic profitability of dampling-based integrated management of wheat in country elevators

Science.gov (United States)

Integrated pest management provides the potential for better insect management in stored wheat, as well as increased worker safety and reduced environmental concerns. Many country elevators, however, continue to use chemical-based approaches. To determine if this choice is economically justified, to...

The Next Challenge: Advancement of Low-Skilled, Low-Wage Workers

Science.gov (United States)

Rubin, Jerry

2004-01-01

With the series "Advancement for Low-Wage Workers," Jobs for the Future seeks to elevate discussion of this critical issue within and outside the workforce field. These occasional papers address public policy and on-the-ground practice. "The Next Challenge," the series introduction, argues for placing not just employment, but also advancement at…

Risk of occupational radiation-induced cataract in medical workers

International Nuclear Information System (INIS)

Snezana, Milacic

2008-01-01

The objective of this study was determination of criteria for recognition of a pre senile cataract as a professional disease in health care personnel exposed to small doses of ionizing radiation. Method: The study included 3240 health workers in medical centers of Serbia in the period 1992-2002. A total of 1560 workers were employed in the zone (group A) and 1680 out of ionizing radiation zone (group B). Among group A, two groups had been selected: 1. Group A-1: Health workers in the ionizing radiation zone who contracted lens cataract during their years of service while dosimetry could not reveal higher absorbed dose (A-1=115); 2. Group A-2: Health workers in the ionizing radiation zone with higher incidence of chromosomal aberrations and without cataract (A-2=100). Results: More significant incidence of cataract was found in group A, χ 2 =65.92; p<0.01. Radiation risk was higher in health workers in radiation zone than in others, relative risk is 4, 6. Elevated blood sugar level was found in higher percentage with health workers working in radiation zone who developed cataract. Conclusion: Low doses of radiation are not the cause of occupational cataract as individual occupational disease. X-ray radiation may be a significant cofactor of cataract in radiological technicians. (author)

Physico-chemical characterization of grain dust in storage air of Bangalore.

Science.gov (United States)

Mukherjee, A K; Nag, D P; Kakde, Y; Babu, K R; Prdkash, M N; Rao, S R

1998-06-01

An Anderson personal cascade impactor was used to study the particle mass size distribution in the storage air of two major grain storage centers in Bangalore. Dust levels in storage air as well as the personal exposures of workers were determined along with a detailed study on the particle size distribution. Protein and carbohydrate content of the dust were also determined respectively in the phosphate buffer saline (PBS) and water extracts by using the standard analytical techniques. Personal exposures in both of the grain storage centers have been found to be much above the limit prescribed by ACGIH (1995-96). But the results of particle size analysis showed a higher particle mass distribution in the non-respirable size range. The mass median diameters (MMD) of the storage air particulate of both the centers were found to be beyond the respirable range. Presence of protein and carbohydrate in the storage air dust is indicative of the existence of glyco-proteins, mostly of membrane origin.

Grain-size sorting and slope failure in experimental subaqueous grain flows

NARCIS (Netherlands)

Kleinhans, M.G.; Asch, Th.W.J. van

2005-01-01

Grain-size sorting in subaqueous grain flows of a continuous range of grain sizes is studied experimentally with three mixtures. The observed pattern is a combination of stratification and gradual segregation. The stratification is caused by kinematic sieving in the grain flow. The segregation is

Cycling-induced degradation of LiCoO2 thin-film cathodes at elevated temperature

International Nuclear Information System (INIS)

Van Sluytman, J.S.; West, W.C.; Whitacre, J.F.; Alamgir, F.M.; Greenbaum, S.G.

2006-01-01

The cycle life of LiCoO 2 -based all solid-state thin-film cells has been studied at room temperature, and at elevated temperatures of 50, 100, and 150 deg. C. X-ray diffraction, as well as Raman analysis, has been used to complement the electrochemical data in examining structural and chemical changes. XRD and Raman spectroscopy data indicate that elevated temperature soaks of the thin-film batteries in the quiescent state causes no discernable changes in the LiCoO 2 cathode layer. However, when the thin-film batteries are cycled at elevated temperatures, decreases in average grain size of the LiCoO 2 film occur with dramatic concomitant charge and discharge capacity loss

Effect of service exposure on fatigue crack propagation of Inconel 718 turbine disc material at elevated temperatures

Energy Technology Data Exchange (ETDEWEB)

Jeong, Dae-Ho [Department of Materials Science and Engineering, RECAPT, Gyeongsang National University, Chinju (Korea, Republic of); Choi, Myung-Je [Korea Aerospace Industry, Sacheon (Korea, Republic of); Goto, Masahiro [Department of Mechanical Engineering, Oita University, Oita (Japan); Lee, Hong-Chul [Republic of Korea Air Force (Korea, Republic of); Kim, Sangshik, E-mail: sang@gnu.ac.kr [Department of Materials Science and Engineering, RECAPT, Gyeongsang National University, Chinju (Korea, Republic of)

2014-09-15

In this study, the fatigue crack propagation behavior of Inconel 718 turbine disc with different service times from 0 to 4229 h was investigated at 738 and 823 K. No notable change in microstructural features, other than the increase in grain size, was observed with increasing service time. With increasing service time from 0 to 4229 h, the fatigue crack propagation rates tended to increase, while the ΔK{sub th} value decreased, in low ΔK regime and lower Paris' regime at both testing temperatures. The fractographic observation using a scanning electron microscope suggested that the elevated temperature fatigue crack propagation mechanism of Inconel 718 changed from crystallographic cleavage mechanism to striation mechanism in the low ΔK regime, depending on the grain size. The fatigue crack propagation mechanism is proposed for the crack propagating through small and large grains in the low ΔK regime, and the fatigue crack propagation behavior of Inconel 718 with different service times at elevated temperatures is discussed. - Highlights: • The specimens were prepared from the Inconel 718 turbine disc used for 0 to 4229 h. • FCP rates were measured at 738 and 823 K. • The ΔK{sub th} values decreased with increasing service time. • The FCP behavior showed a strong correlation with the grain size of used turbine disc.

Experimental human exposure to inhaled grain dust and ammonia: towards a model of concentrated animal feeding operations.

Science.gov (United States)

Sigurdarson, Sigurdur T; O'Shaughnessy, Patrick T; Watt, Janet A; Kline, Joel N

2004-10-01

Ammonia and endotoxin-rich dust are present in high concentrations in swine confinement facilities; exposure to this environment is linked to workers' respiratory problems. We hypothesized that experimental exposure to ammonia and dust would impair pulmonary function, and that these exposures would be synergistic. We exposed six normal subjects and eight subjects with mild asthma to ammonia (16-25 ppm) and/or endotoxin-rich grain dust (4 mg/m3). Pulmonary function and exhaled NOx were measured before and after exposure. There was no significant change in pulmonary function in the normal subjects following any of the exposure conditions. Among asthmatics, a significant transient decrease in FEV1 was induced by grain dust, but was not altered by ammonia; increased bronchial hyperreactivity was also noted in this group. In a vulnerable population, exposure to grain dust results in transient airflow obstruction. Short-term exposure to ammonia does not increase this response.

A comparison of grain boundary evolution during grain growth in fcc metals

International Nuclear Information System (INIS)

Brons, J.G.; Thompson, G.B.

2013-01-01

Grain growth of Cu and Ni thin films, subjected to in situ annealing within a transmission electron microscope, has been quantified using a precession-enhanced electron diffraction technique. The orientation of each grain and its misorientation with respect to its neighboring grains were calculated. The Cu underwent grain growth that maintained a monomodal grain size distribution, with its low-angle grain boundaries being consumed, and the Ni exhibited grain size distributions in stages, from monomodal to bimodal to monomodal. The onset of Ni’s abnormal grain growth was accompanied by a sharp increase in the Σ3 and Σ9 boundary fractions, which is attributed to simulation predictions of their increased mobility. These Σ3 and Σ9 fractions then dropped to their room temperature values during the third stage of grain growth. In addition to the Σ3 and Σ9 boundaries, the Σ5 and Σ7 boundaries also underwent an increase in total boundary fraction with increasing temperature in both metals

Assessing Heat Stress and Health among Construction Workers in a Changing Climate: A Review

Directory of Open Access Journals (Sweden)

Payel Acharya

2018-02-01

Full Text Available Construction workers are at an elevated risk of heat stress, due to the strenuous nature of the work, high temperature work condition, and a changing climate. An increasing number of workers are at risk, as the industry’s growth has been fueled by high demand and vast numbers of immigrant workers entering into the U.S., the Middle East and Asia to meet the demand. The risk of heat-related illnesses is increased by the fact that little to no regulations are present and/or enforced to protect these workers. This review recognizes the issues by summarizing epidemiological studies both in the U.S. and internationally. These studies have assessed the severity with which construction workers are affected by heat stress, risk factors and co-morbidities associated with heat-related illnesses in the construction industry, vulnerable populations, and efforts in implementing preventive measures.

Cross-shift study of exposure-response relationships between bioaerosol exposure and respiratory effects in the Norwegian grain and animal feed production industry

NARCIS (Netherlands)

Straumfors, Anne; Heldal, Kari Kulvik; Eduard, Wijnand; Wouters, Inge M; Ellingsen, Dag G; Skogstad, Marit

2016-01-01

OBJECTIVE: We have studied cross-shift respiratory responses of several individual bioaerosol components of the dust in the grain and feed industry in Norway. METHODS: Cross-shift changes in lung function and nasal congestion, as well as in respiratory and systemic symptoms of 56 exposed workers and

Worker doses and potential health effects resulting from the accident at the Fukushima nuclear power plant in 2011.

Science.gov (United States)

Etherington, George; Zhang, Wei; Harrison, John; Walsh, Linda

2014-11-01

The reliability of exposure scenarios used in the World Health Organization's Health Risk Assessment (HRA) for Fukushima workers was examined. HRA risk estimates for cancer incidence in these workers were then reviewed. The HRA constructed four exposure scenarios to estimate worker radiation doses; recent individual dosimetric data were used to assess their reliability. Risks of specified cancer types attributable to radiation exposure were estimated in the HRA by calculating Lifetime Attributable Risks (LAR) for each scenario, and comparisons of LAR are provided. The scenarios were confirmed as reliable for the purposes of the HRA. For the lowest dose scenario (Scenario 1: 69% of the workforce), the HRA found that any elevated cancer risk was insignificant. Significantly elevated cancer risks were, however, found for the three higher dose scenarios. For the highest dose scenario (Scenario 4: 13 workers), LAR values for thyroid cancer up to 3.5% were estimated, but a radiation-related increase in thyroid cancer incidence is unlikely to be observed because of the small number of workers. For the two intermediate dose scenarios, a small number of cancer cases may occur, but these are unlikely to be observed because the variability in baseline rates of cancer incidence is much larger than the predicted radiation-related incidence rates.

Flume Experiments on the Influence of Salmon Spawning Density on Grain Stability and Bedload Transport in Gravel-bed Streams

Science.gov (United States)

Buxton, T. H.

2015-12-01

Salmon spawning in streams involves the female salmon digging a pit in the bed where she deposits eggs for fertilization before covering them with gravel excavated from the next pit upstream. Sequences of pit excavation and filling winnow fines, loosen sediment, and move bed material into a tailspill mound resembling the shape of a dune. Research suggests salmonid nests (redds) destabilize streambeds by reducing friction between loosened grains and converging flow that elevates shear stress on redd topography. However, bed stability may be enhanced by form drag from redds in clusters that lower shear stress on the granular bed, but this effect will vary with the proportion of the bed surface that is occupied by redds (P). I used simulated redds and water-worked ("unspawned") beds in a laboratory flume to evaluate these competing influences on grain stability and bedload transport rates with P=0.12, 0.34, and 0.41. Results indicate that competence (largest-grain) and reference transport rate estimates of critical conditions for particle entrainment inversely relate to P. Bedload transport increased as exponential functions of P and excess boundary shear stress. Therefore, redd form drag did not overcome the destabilizing effects of spawning. Instead, grain mobility and bedload transport increased with P because larger areas of the bed were composed of relatively loose, unstable grains and redd topography that experienced elevated shear stress. Consequently, the presence of redds in fish-bearing streams likely reduces the effects of sedimentation from landscape disturbance on stream habitats that salmon use for reproduction.

Mechanism of secondary recrystallization of Goss grains in grain-oriented electrical steel

Science.gov (United States)

Hayakawa, Yasuyuki

2017-12-01

Since its invention by Goss in 1934, grain-oriented (GO) electrical steel has been widely used as a core material in transformers. GO exhibits a grain size of over several millimeters attained by secondary recrystallization during high-temperature final batch annealing. In addition to the unusually large grain size, the crystal direction in the rolling direction is aligned with , which is the easy magnetization axis of α-iron. Secondary recrystallization is the phenomenon in which a certain very small number of {110} (Goss) grains grow selectively (about one in 106 primary grains) at the expense of many other primary recrystallized grains. The question of why the Goss orientation is exclusively selected during secondary recrystallization has long been a main research subject in this field. The general criterion for secondary recrystallization is a small and uniform primary grain size, which is achieved through the inhibition of normal grain growth by fine precipitates called inhibitors. This paper describes several conceivable mechanisms of secondary recrystallization of Goss grains mainly based on the selective growth model.

Grain-boundary engineering applied to grain growth in a high temperature material

International Nuclear Information System (INIS)

Huda, Z.

1993-01-01

Crystallography of grain boundaries are determined for a high temperature material, before and after grain growth processes, so as to study the induction of special properties useful for application in components of a gas-turbine engine. The philosophy of grain-boundary engineering is applied to grain growth in APK-6, a powder formed nickel-base superalloy so as to establish the possible structure/property relationships. The alloy in the as received condition is shown to possess a strong texture and contained coincident site lattices (CSL) boundaries with most boundaries having sigma values in the range of 3 > sigma > 25. A normal grain-growth heat treatment result in a good population of low angle grain boundaries, and drastically reduces the proportion of CSL boundaries. A strong [011] annealing texture is observed after an intermediate grain growth; most grain boundaries, here, tend to be high angle indicating a possibility of possessing special properties. (author)

Biological monitoring results for cadmium exposed workers.

Science.gov (United States)

McDiarmid, M A; Freeman, C S; Grossman, E A; Martonik, J

1996-11-01

As part of a settlement agreement with the Occupational Safety and Health Administration (OSHA) involving exposure to cadmium (Cd), a battery production facility provided medical surveillance data to OSHA for review. Measurements of cadmium in blood, cadmium in urine, and beta 2-microglobulin in urine were obtained for more than 100 workers over an 18-month period. Some airborne Cd exposure data were also made available. Two subpopulations of this cohort were of primary interest in evaluating compliance with the medical surveillance provisions of the Cadmium Standard. These were a group of 16 workers medically removed from cadmium exposure due to elevations in some biological parameter, and a group of platemakers. Platemaking had presented a particularly high exposure opportunity and had recently undergone engineering interventions to minimize exposure. The effect on three biological monitoring parameters of medical removal protection in the first group and engineering controls in platemakers is reported. Results reveal that both medical removal from cadmium exposures and exposure abatement through the use of engineering and work practice controls generally result in declines in biological monitoring parameters of exposed workers. Implications for the success of interventions are discussed.

Phloem Transport of Arsenic Species from Flag Leaf to Grain During Grain Filling

Energy Technology Data Exchange (ETDEWEB)

A Carey; G Norton; C Deacon; K Scheckel; E Lombi; T Punshon; M Guerinot; A Lanzirotti; M Newville; et al.

2011-12-31

Strategies to reduce arsenic (As) in rice grain, below concentrations that represent a serious human health concern, require that the mechanisms of As accumulation within grain be established. Therefore, retranslocation of As species from flag leaves into filling rice grain was investigated. Arsenic species were delivered through cut flag leaves during grain fill. Spatial unloading within grains was investigated using synchrotron X-ray fluorescence (SXRF) microtomography. Additionally, the effect of germanic acid (a silicic acid analog) on grain As accumulation in arsenite-treated panicles was examined. Dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) were extremely efficiently retranslocated from flag leaves to rice grain; arsenate was poorly retranslocated, and was rapidly reduced to arsenite within flag leaves; arsenite displayed no retranslocation. Within grains, DMA rapidly dispersed while MMA and inorganic As remained close to the entry point. Germanic acid addition did not affect grain As in arsenite-treated panicles. Three-dimensional SXRF microtomography gave further information on arsenite localization in the ovular vascular trace (OVT) of rice grains. These results demonstrate that inorganic As is poorly remobilized, while organic species are readily remobilized, from leaves to grain. Stem translocation of inorganic As may not rely solely on silicic acid transporters.

Phloem transport of arsenic species from flag leaf to grain during grain filling

Energy Technology Data Exchange (ETDEWEB)

Carey, Anne-Marie; Norton, Gareth J.; Deacon, Claire; Scheckel, Kirk G.; Lombi, Enzo; Punshon, Tracy; Guerinot, Mary Lou; Lanzirotti, Antonio; Newville, Matt; Choi, Yongseong; Price, Adam H.; Meharg, Andrew A. (EPA); (U. South Australia); (Aberdeen); (UC); (Dartmouth)

2011-09-20

Strategies to reduce arsenic (As) in rice grain, below concentrations that represent a serious human health concern, require that the mechanisms of As accumulation within grain be established. Therefore, retranslocation of As species from flag leaves into filling rice grain was investigated. Arsenic species were delivered through cut flag leaves during grain fill. Spatial unloading within grains was investigated using synchrotron X-ray fluorescence (SXRF) microtomography. Additionally, the effect of germanic acid (a silicic acid analog) on grain As accumulation in arsenite-treated panicles was examined. Dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) were extremely efficiently retranslocated from flag leaves to rice grain; arsenate was poorly retranslocated, and was rapidly reduced to arsenite within flag leaves; arsenite displayed no retranslocation. Within grains, DMA rapidly dispersed while MMA and inorganic As remained close to the entry point. Germanic acid addition did not affect grain As in arsenite-treated panicles. Three-dimensional SXRF microtomography gave further information on arsenite localization in the ovular vascular trace (OVT) of rice grains. These results demonstrate that inorganic As is poorly remobilized, while organic species are readily remobilized, from leaves to grain. Stem translocation of inorganic As may not rely solely on silicic acid transporters.

Testing a Model of Functional Impairment in Telephone Crisis Support Workers.

Science.gov (United States)

Kitchingman, Taneile A; Wilson, Coralie J; Caputi, Peter; Wilson, Ian; Woodward, Alan

2017-11-01

It is well known that helping professionals experience functional impairment related to elevated symptoms of psychological distress as a result of frequent empathic engagement with distressed others. Whether telephone crisis support workers are impacted in a similar way is not currently reported in the literature. The purpose of this study was to test a hypothesized model of factors contributing to functional impairment in telephone crisis support workers. A national sample of 210 telephone crisis support workers completed an online survey including measures of emotion regulation, symptoms of general psychological distress and suicidal ideation, intentions to seek help for symptoms, and functional impairment. Structural equation modeling was used to test the fit of the data to the hypothesized model. Goodness-of-fit indices were adequate and supported the interactive effects of emotion regulation, general psychological distress, suicidal ideation, and intentions to seek help for ideation on functional impairment. These results warrant the deliberate management of telephone crisis support workers' impairment through service selection, training, supervision, and professional development strategies. Future research replicating and extending this model will further inform the modification and/or development of strategies to optimize telephone crisis support workers' well-being and delivery of support to callers.

Ionizing radiation for insect control in grain and grain products

International Nuclear Information System (INIS)

Tilton, E.W.; Brower, J.H.

1987-01-01

A technical review summarizes and discusses information on various aspects of the use of ionizing radiation for the control of insect infestation in grains and grain products. Topics include: the effects of ionizing radiation on insects infesting stored-grain products; the 2 main types of irradiators (electron accelerators; radioisotopes (e.g.: Co-60; Cs-137); dosimetry systems and methodology; variations in radiation resistance by stored-product pests; the proper selection of radiation dose; the effects of combining various treatments (temperature, infrared/microwave radiation, hypoxia, chemicals) with ionizing radiation; sublethal radiation for controlling bulk grain insects; the feeding capacity of irradiated insects; the susceptibility of insecticide-resistant insects to ionizing radiation; and the possible resistance of insects to ionizing radiation. Practical aspects of removing insects from irradiated grain also are discussed

Stress-assisted grain growth in nanocrystalline metals: Grain boundary mediated mechanisms and stabilization through alloying

International Nuclear Information System (INIS)

Zhang, Yang; Tucker, Garritt J.; Trelewicz, Jason R.

2017-01-01

The mechanisms of stress-assisted grain growth are explored using molecular dynamics simulations of nanoindentation in nanocrystalline Ni and Ni-1 at.% P as a function of grain size and deformation temperature. Grain coalescence is primarily confined to the high stress region beneath the simulated indentation zone in nanocrystalline Ni with a grain size of 3 nm. Grain orientation and atomic displacement vector mapping demonstrates that coalescence transpires through grain rotation and grain boundary migration, which are manifested in the grain interior and grain boundary components of the average microrotation. A doubling of the grain size to 6 nm and addition of 1 at.% P eliminates stress-assisted grain growth in Ni. In the absence of grain coalescence, deformation is accommodated by grain boundary-mediated dislocation plasticity and thermally activated in pure nanocrystalline Ni. By adding solute to the grain boundaries, the temperature-dependent deformation behavior observed in both the lattice and grain boundaries inverts, indicating that the individual processes of dislocation and grain boundary plasticity will exhibit different activity based on boundary chemistry and deformation temperature.

Hormonal changes in the grains of rice subjected to water stress during grain filling.

Science.gov (United States)

Yang, J; Zhang, J; Wang, Z; Zhu, Q; Wang, W

2001-09-01

Lodging-resistant rice (Oryza sativa) cultivars usually show slow grain filling when nitrogen is applied in large amounts. This study investigated the possibility that a hormonal change may mediate the effect of water deficit that enhances whole plant senescence and speeds up grain filling. Two rice cultivars showing high lodging resistance and slow grain filling were field grown and applied with either normal or high amount nitrogen (HN) at heading. Well-watered and water-stressed (WS) treatments were imposed 9 days post anthesis to maturity. Results showed that WS increased partitioning of fixed (14)CO(2) into grains, accelerated the grain filling rate but shortened the grain filling period, whereas the HN did the opposite way. Cytokinin (zeatin + zeatin riboside) and indole-3-acetic acid contents in the grains transiently increased at early filling stage and WS treatments hastened their declines at the late grain filling stage. Gibberellins (GAs; GA(1) + GA(4)) in the grains were also high at early grain filling but HN enhanced, whereas WS substantially reduced, its accumulation. Opposite to GAs, abscisic acid (ABA) in the grains was low at early grain filling but WS remarkably enhanced its accumulation. The peak values of ABA were significantly correlated with the maximum grain filling rates (r = 0.92**, P water stress during grain filling, especially a decrease in GAs and an increase in ABA, enhances the remobilization of prestored carbon to the grains and accelerates the grain filling rate.

Characteristics of worker accidents on NYSDOT construction projects.

Science.gov (United States)

Mohan, Satish; Zech, Wesley C

2005-01-01

This paper aims at providing cost-effective safety measures to protect construction workers in highway work zones, based on real data. Two types of accidents that occur in work zones were: (a) construction work area accidents, and (b) traffic accidents involving construction worker(s). A detailed analysis of work zone accidents involving 36 fatalities and 3,055 severe injuries to construction workers on New York State Department of Transportation (NYSDOT) construction projects from 1990 to 2001 established that five accident types: (a) Struck/Pinned by Large Equipment, (b) Trip or Fall (elevated), (c) Contact w/Electrical or Gas Utility, (d) Struck-by Moving/Falling Load, and (e) Crane/Lift Device Failure accounted for nearly 96% of the fatal accidents, nearly 63% of the hospital-level injury accidents, and nearly 91% of the total costs. These construction work area accidents had a total cost of $133.8 million. Traffic accidents that involve contractors' employees were also examined. Statistical analyses of the traffic accidents established that five traffic accident types: (a) Work Space Intrusion, (b) Worker Struck-by Vehicle Inside Work Space, (c) Flagger Struck-by Vehicle, (d) Worker Struck-by Vehicle Entering/Exiting Work Space, and (e) Construction Equipment Struck-by Vehicle Inside Work Space accounted for nearly 86% of the fatal, nearly 70% of the hospital-level injury and minor injury traffic accidents, and $45.4 million (79.4%) of the total traffic accident costs. The results of this paper provide real statistics on construction worker related accidents reported on construction work zones. Potential preventions based on real statistics have also been suggested. The ranking of accident types, both within the work area as well as in traffic, will guide the heavy highway contractor and owner agencies in identifying the most cost effective safety preventions.

Grain dynamics and inter-grain coupling in dusty plasma Coulomb crystals

International Nuclear Information System (INIS)

Rahman, H.U.; Mohideen, U.; Smith, M.A.; Rosenberg, M.; Mendis, D.A.

2001-01-01

We review our results on the lattice structure and the lattice dynamics of dusty plasma Coulomb crystals formed in rectangular conductive grooves. The basic structure appears to be made of mutually repulsive columns of grains confined by the walls of the groove. The columns are oriented along the direction of the electrode sheath electric field. Inter-grain coupling as a function of plasma temperature and density were investigated by measurement of these parameters. A simple phenomenological model wherein the inter-grain spacing along the column results from an attractive electric field induced dipole-dipole force balanced by a repulsive monopole Coulomb force is consistent with observed features of the Coulomb crystal. In addition, here we present some preliminary measurements of the vibration and rotation dynamics of the individual grains in the Coulomb crystal. The thermal energy of the dust grain thus calculated is much less than the inter-grain Coulomb potential energy as required for the formation of stable structures. Also the observed rotational frequency is consistent with the assumption of thermal equilibrium between the dust grains and the neutral gas. (orig.)

Screening heavy metals levels in hair of sanitation workers by X-ray fluorescence analysis

International Nuclear Information System (INIS)

Md Khudzari, Jauharah; Wagiran, Husin; Hossain, I.; Ibrahim, Noorddin

2013-01-01

This work presents a study of human hair as a bio-indicator for detection of heavy metals as part of environmental health surveillance programs project to develop a subject of interest in the biomedical and environmental sciences. A total of 34 hair samples were analyzed that consisting of 29 samples from sanitation workers and five samples from students. The hair samples were prepared and treated in accordance to the International Atomic Energy Agency (IAEA) recommendations. The concentrations of heavy metals were analyzed using the energy dispersive X-ray fluorescence (EDXRF) technique by X-50 Mobile X-ray Fluorescence (XRF) at Oceanography Institute, Universiti Malaysia Terengganu. The performance of EDXRF analyzer was tested by Standard Reference Material (SRM 2711) Montana Soil which was in good agreement with certified value within 14% deviations except for Hg. While seven heavy metals: Mn, Fe, Ni, Cu, Zn, Se, and Sb were detected in both groups, three additional elements, i.e. As, Hg and Pb, were detected only in sanitation workers group. For sanitation workers group, the mean concentration of six elements, Mn, Fe, Cu, Zn, Se, and Sb, shows elevated concentration as compared to the control samples concentration. Results from both groups were compared and discussed in relation to their respective heavy metals concentrations. - Highlights: ► We determine heavy metals in hair sample of sanitation workers and control group. ► 7 heavy metals, Mn, Fe, Ni, Cu, Zn, Se, and Sb, were detected in both groups. ► Additional elements of As, Hg and Pb were discovered only in sanitation workers. ► Generally, mean concentration of sanitation workers show elevation in comparison. ► We report results in relation to their respective heavy metals concentrations.

Exogenous Cytokinins Increase Grain Yield of Winter Wheat Cultivars by Improving Stay-Green Characteristics under Heat Stress.

Directory of Open Access Journals (Sweden)

Dongqing Yang

Full Text Available Stay-green, a key trait of wheat, can not only increase the yield of wheat but also its resistance to heat stress during active photosynthesis. Cytokinins are the most potent general coordinator between the stay-green trait and senescence. The objectives of the present study were to identify and assess the effects of cytokinins on the photosynthetic organ and heat resistance in wheat. Two winter wheat cultivars, Wennong 6 (a stay-green cultivar and Jimai 20 (a control cultivar, were subjected to heat stress treatment from 1 to 5 days after anthesis (DAA. The two cultivars were sprayed daily with 10 mg L-1 of 6-benzylaminopurine (6-BA between 1 and 3 DAA under ambient and elevated temperature conditions. We found that the heat stress significantly decreased the number of kernels per spike and the grain yield (P < 0.05. Heat stress also decreased the zeatin riboside (ZR content, but increased the gibberellin (GA3, indole-3-acetic acid (IAA, and abscisic acid (ABA contents at 3 to 15 DAA. Application of 6-BA significantly (P < 0.05 increased the grain-filling rate, endosperm cell division rate, endosperm cell number, and 1,000-grain weight under heated condition. 6-BA application increased ZR and IAA contents at 3 to 28 DAA, but decreased GA3 and ABA contents. The contents of ZR, ABA, and IAA in kernels were positively and significantly correlated with the grain-filling rate (P < 0.05, whereas GA3 was counter-productive at 3 to 15 DAA. These results suggest that the decrease in grain yield under heat stress was due to a lower ZR content and a higher GA3 content compared to that at elevated temperature during the early development of the kernels, which resulted in less kernel number and lower grain-filling rate. The results also provide essential information for further utilization of the cytokinin substances in the cultivation of heat-resistant wheat.

Microbiota of kefir grains

Directory of Open Access Journals (Sweden)

Tomislav Pogačić

2013-03-01

Full Text Available Kefir grains represent the unique microbial community consisting of bacteria, yeasts, and sometimes filamentous moulds creating complex symbiotic community. The complexity of their physical and microbial structures is the reason that the kefir grains are still not unequivocally elucidated. Microbiota of kefir grains has been studied by many microbiological and molecular approaches. The development of metagenomics, based on the identification without cultivation, is opening new possibilities for identification of previously nonisolated and non-identified microbial species from the kefir grains. Considering recent studies, there are over 50 microbial species associated with kefir grains. The aim of this review is to summarise the microbiota composition of kefir grains. Moreover, because of technological and microbiological significance of the kefir grains, the paper provides an insight into the microbiological and molecular methods applied to study microbial biodiversity of kefir grains.

Mineral composition of durum wheat grain and pasta under increasing atmospheric CO2 concentrations.

Science.gov (United States)

Beleggia, Romina; Fragasso, Mariagiovanna; Miglietta, Franco; Cattivelli, Luigi; Menga, Valeria; Nigro, Franca; Pecchioni, Nicola; Fares, Clara

2018-03-01

The concentrations of 10 minerals were investigated in the grain of 12 durum wheat genotypes grown under free air CO 2 enrichment conditions, and in four of their derived pasta samples, using inductively coupled plasma mass spectrometry. Compared to ambient CO 2 (400ppm; AMB), under elevated CO 2 (570ppm; ELE), the micro-element and macro-element contents showed strong and significant decreases in the grain: Mn, -28.3%; Fe, -26.7%; Zn, -21.9%; Mg, -22.7%; Mo, -40.4%; K, -22.4%; and Ca, -19.5%. These variations defined the 12 genotypes as sensitive or non-sensitive to ELE. The pasta samples under AMB and ELE showed decreased mineral contents compared to the grain. Nevertheless, the contributions of the pasta to the recommended daily allowances remained relevant, also for the micro-elements under ELE conditions (range, from 18% of the recommended daily allowance for Zn, to 70% for Mn and Mo). Copyright © 2017 Elsevier Ltd. All rights reserved.

Environments with elevated radiation levels from natural radioactive substances

International Nuclear Information System (INIS)

Sohrabi, M.

2000-01-01

Some areas in the world have elevated levels of radioactive substances in the environment forming elevated radiation areas (ERAs) where public potential annual effective doses can exceed even the dose limit of radiation workers. Such radioactive substances are either terrestrial natural radioactivity added naturally in the soil or natural and/or man-made radioactivity from human activities added into the environment. If radioactivity is added naturally, elevated natural radiation areas (ENRAs) are formed. Based on the classification criteria introduced by the author, such regions are divided into static and dynamic areas. They are also classified in accordance with their level of potential effective dose to the public. Some main ENRAs are classified. Highlights are presented of the results of activity studies carried out in selected areas. The concepts discussed can also be applied to areas formed by human activities. The author suggests some guidelines for future studies, regulatory control and decision making, bearing in mind the need for harmonization of policies for regulatory control and remedial actions at sites to protect the public from environmental chronic exposures. (author)

Origins of GEMS Grains

Science.gov (United States)

Messenger, S.; Walker, R. M.

2012-01-01

Interplanetary dust particles (IDPs) collected in the Earth s stratosphere contain high abundances of submicrometer amorphous silicates known as GEMS grains. From their birth as condensates in the outflows of oxygen-rich evolved stars, processing in interstellar space, and incorporation into disks around new stars, amorphous silicates predominate in most astrophysical environments. Amorphous silicates were a major building block of our Solar System and are prominent in infrared spectra of comets. Anhydrous interplanetary dust particles (IDPs) thought to derive from comets contain abundant amorphous silicates known as GEMS (glass with embedded metal and sulfides) grains. GEMS grains have been proposed to be isotopically and chemically homogenized interstellar amorphous silicate dust. We evaluated this hypothesis through coordinated chemical and isotopic analyses of GEMS grains in a suite of IDPs to constrain their origins. GEMS grains show order of magnitude variations in Mg, Fe, Ca, and S abundances. GEMS grains do not match the average element abundances inferred for ISM dust containing on average, too little Mg, Fe, and Ca, and too much S. GEMS grains have complementary compositions to the crystalline components in IDPs suggesting that they formed from the same reservoir. We did not observe any unequivocal microstructural or chemical evidence that GEMS grains experienced prolonged exposure to radiation. We identified four GEMS grains having O isotopic compositions that point to origins in red giant branch or asymptotic giant branch stars and supernovae. Based on their O isotopic compositions, we estimate that 1-6% of GEMS grains are surviving circumstellar grains. The remaining 94-99% of GEMS grains have O isotopic compositions that are indistinguishable from terrestrial materials and carbonaceous chondrites. These isotopically solar GEMS grains either formed in the Solar System or were completely homogenized in the interstellar medium (ISM). However, the

Monocular Elevation Deficiency - Double Elevator Palsy

Science.gov (United States)

... Español Condiciones Chinese Conditions Monocular Elevation Deficiency/ Double Elevator Palsy En Español Read in Chinese What is monocular elevation deficiency (Double Elevator Palsy)? Monocular Elevation Deficiency, also known by the ...

The effects of irradiation on grain coat color and grain texture in winter wheat

International Nuclear Information System (INIS)

Miao Bingliang; Liu Xueyu

1989-01-01

Dry seeds of the variety ''Yangmai 5'' with red grain coat, semihard grain texture, and the variety ''Ningmai 3'' with red grain coat, soft grain texture were irradiated with Y-rays at various doses.The effect on M1 grain coat color was different between two varieties, the higher doses made grain coat color of ''Yangmai 5'' redder, but had hardly effect on ''Ningmai 3''.The effect on M1 grain texture showed that the grain texture became softer with doses increased.It was found that there were 0.6% of positive ( red to white ) grain coat color mutants and 2.0% of negative(hard to soft) grain texture mutants in M2 of ''Yangmai 5'', and there were 0.7% of negative ( white to red ) grain coat color mutants and 3.6% of positive ( soft to hard ) grain texture mutants in M2 of ''Ningmai 3''. It seemed that the positive mutants selected in M3 were stable in M4. The results showed that γ-rays can be used to improve the grain coat color andgrain texture of wheat varieties

Grain size stability and hardness in nanocrystalline Cu–Al–Zr and Cu–Al–Y alloys

Energy Technology Data Exchange (ETDEWEB)

Roy, D., E-mail: droy2k6@gmail.com [Material Science and Engineering Department, North Carolina State University, Raleigh, NC 27606 (United States); Materials and Metallurgical Engineering Department, NIFFT, Ranchi 834003 (India); Mahesh, B.V. [Department of Mechanical and Aerospace Engineering, Monash University (Australia); Atwater, M.A. [U.S. Army Research Laboratory, Weapons and Materials Research Directorate, RDRL-WMM-F, Aberdeen Proving Ground, MD 21005-5069 (United States); Chan, T.E.; Scattergood, R.O.; Koch, C.C. [Material Science and Engineering Department, North Carolina State University, Raleigh, NC 27606 (United States)

2014-03-01

Cryogenic high energy ball milling has been used to synthesize nanocrystalline Cu–14Al, Cu–12Al–2Zr and Cu–12Al–2Y alloys by mechanical alloying. The alloys were studied with the aim of comparing the effect of substituting Y and Zr in place of Al, in Cu–Al alloys, on the grain size stability at elevated temperatures. The as-milled alloys were subjected to annealing at various temperatures between 200 and 900 °C and the resulting grain morphology has been studied using X-ray diffraction and transmission electron microscopy. The addition of Y results in significantly reduced susceptibility to grain growth whereas in case of CuAl and CuAlZr alloys, the susceptibility to grain growth was much higher. The hardness is substantially increased due to Zr and Y addition in the as-milled CuAl powders. However, the hardness of Cu–12Al–2Zr gradually decreases and approaches that of Cu–14Al alloy after the annealing treatment whereas in case of Cu–12Al–2Y alloy, the relative drop in the hardness is much lower after annealing. Accordingly, the efficacy of grain size stabilization by Y addition at high homologous temperatures has been explained on the basis of a recent thermodynamic stabilization models.

Grain size stability and hardness in nanocrystalline Cu–Al–Zr and Cu–Al–Y alloys

International Nuclear Information System (INIS)

Roy, D.; Mahesh, B.V.; Atwater, M.A.; Chan, T.E.; Scattergood, R.O.; Koch, C.C.

2014-01-01

Cryogenic high energy ball milling has been used to synthesize nanocrystalline Cu–14Al, Cu–12Al–2Zr and Cu–12Al–2Y alloys by mechanical alloying. The alloys were studied with the aim of comparing the effect of substituting Y and Zr in place of Al, in Cu–Al alloys, on the grain size stability at elevated temperatures. The as-milled alloys were subjected to annealing at various temperatures between 200 and 900 °C and the resulting grain morphology has been studied using X-ray diffraction and transmission electron microscopy. The addition of Y results in significantly reduced susceptibility to grain growth whereas in case of CuAl and CuAlZr alloys, the susceptibility to grain growth was much higher. The hardness is substantially increased due to Zr and Y addition in the as-milled CuAl powders. However, the hardness of Cu–12Al–2Zr gradually decreases and approaches that of Cu–14Al alloy after the annealing treatment whereas in case of Cu–12Al–2Y alloy, the relative drop in the hardness is much lower after annealing. Accordingly, the efficacy of grain size stabilization by Y addition at high homologous temperatures has been explained on the basis of a recent thermodynamic stabilization models

Respiratory tract mortality in cement workers: a proportionate mortality study

Science.gov (United States)

2012-01-01

Background The evidence regarding the association between lung cancer and occupational exposure to cement is controversial. This study investigated causes of deaths from cancer of respiratory tract among cement workers. Methods The deaths of the Greek Cement Workers Compensation Scheme were analyzed covering the period 1969-1998. All respiratory, lung, laryngeal and urinary bladder cancer proportionate mortality were calculated for cement production, maintenance, and office workers in the cement industry. Mortality from urinary bladder cancer was used as an indirect indicator of the confounding effect of smoking. Results Mortality from all respiratory cancer was significantly increased in cement production workers (PMR = 1.91; 95% CI 1.54 to 2.33). The proportionate mortality from lung cancer was significantly elevated (PMR = 2.05; 95% CI 1.65 to 2.52). A statistically significant increase in proportionate mortality due to respiratory (PMR = 1.7; 95% CI 1.2 to 2.34). and lung cancer (PMR = 1.67;95% CI = 1.15-2.34) among maintenance workers has been observed. The PMR among the three groups of workers (production, maintenance, office) did differ significantly for lung cancer (p = 0.001), while the PMR for urinary bladder cancer found to be similar among the three groups of cement workers. Conclusion Cement production, and maintenance workers presented increased lung and respiratory cancer proportionate mortality, and this finding probably cannot be explained by the confounding effect of smoking alone. Further research including use of prospective cohort studies is needed in order to establish a causal association between occupational exposure to cement and risk of lung cancer. PMID:22738120

Grain boundary and grain interior conduction in γ'-Bi2MoO6

International Nuclear Information System (INIS)

Vera, C.M.C.; Aragon, R.

2005-01-01

Impedance spectroscopy of fine grained ( 2 MoO 6 samples, in the frequency range of 0.1 Hz-250 kHz, relevant to sensor applications, up to 800 deg. C, has been used to characterize grain boundary and grain interior contributions to conduction. Above 500 deg. C, the grain boundary contribution is no longer rate limiting and conduction is dominated by the grain interior component. The corresponding activation energies are 0.98 eV for grain boundary and 0.73 eV for grain interior components. The weak dependence of conductivity on oxygen partial pressure below 500 deg. C can be attributed to electrode-electrolyte interface phenomena, whereas the robust response to ethanol is commensurate with changes in intrinsic ionic conductivity

Grain Entrapment Pressure on the Torso: Can You Breathe while Buried in Grain?

Science.gov (United States)

Moore, Kevin G; Jones, Carol L

2017-04-26

The pressure applied to the chest and back of a simulated grain entrapment victim was measured. Pressure sensors were attached to the chest and back of a manikin that was buried in grain in the vertical position. Measurements were made in four grain types at four grain depths ranging from the top of the manikin's shoulders to 0.61 m (24 in.) over the head. The pressure ranged from 1.6 to 4.0 kPa (0.23 to 0.57 psi). Based on available physiological information, this amount of pressure is unlikely to limit the respiration of an otherwise healthy adult male victim. However, other factors, such as the victim's age, gender, and body position in the grain, may influence respiration. The aspiration of grain appears to be the most likely asphyxiation risk during grain bin entrapment. Entering a grain storage bin is inherently dangerous, and Occupational Safety and Health Administration (OSHA) guidelines for permit-required confined spaces and grain handling facilities must be followed. Due to the risk of grain aspiration during engulfment, the development of safety equipment that could help protect the airway of a victim should be investigated. Copyright© by the American Society of Agricultural Engineers.

Wool and grain dusts stimulate TNF secretion by alveolar macrophages in vitro.

Science.gov (United States)

Brown, D M; Donaldson, K

1996-06-01

The aim of the study was to investigate the ability of two organic dusts, wool and grain, and their soluble leachates to stimulate secretion of tumour necrosis factor (TNF) by rat alveolar macrophages with special reference to the role of lipopolysaccharide (LPS). Rat alveolar macrophages were isolated by bronchoalveolar lavage (BAL) and treated in vitro with whole dust, dust leachates, and a standard LPS preparation. TNF production was measured in supernatants with the L929 cell line bioassay. Both wool and grain dust samples were capable of stimulating TNF release from rat alveolar macrophages in a dose-dependent manner. The standard LPS preparation caused a dose-dependent secretion of TNF. Leachates prepared from the dusts contained LPS and also caused TNF release but leachable LPS could not account for the TNF release and it was clear that non-LPS leachable activity was present in the grain dust and that wool dust particles themselves were capable of causing release of TNF. The role of LPS in wool dust leachates was further investigated by treating peritoneal macrophages from two strains of mice, LPS responders (C3H) and LPS non-responders (C3H/HEJ), with LPS. The non-responder mouse macrophages produced very low concentrations of TNF in response to the wool dust leachates compared with the responders. LPS and other unidentified leachable substances present on the surface of grain dust, and to a lesser extent on wool dust, are a trigger for TNF release by lung macrophages. Wool dust particles themselves stimulate TNF. TNF release from macrophages could contribute to enhancement of inflammatory responses and symptoms of bronchitis and breathlessness in workers exposed to organic dusts such as wool and grain.

Prevalence and Correlates of Current and Former Smoking among Urban Transit Workers

Directory of Open Access Journals (Sweden)

Carol B. Cunradi

2017-12-01

Full Text Available Transit workers constitute a blue-collar occupational group that have elevated smoking rates relative to other sectors of employed adults in the United States. This study analyzed cross-sectional tobacco survey data from 935 workers (60% African American; 37% female employed at an urban public transit agency in California. Prevalence of current and former smoking was 20.3% and 20.6%, respectively. Younger workers were less likely than older workers to be current or former smokers. Having a complete home smoking ban was associated with decreased likelihood of being a smoker [odds ratio (OR = 0.04, 95% confidence interval (CI = 0.01–0.17], as were neutral views about whether it is easy for a smoker to take a smoking break during their shift (OR = 0.50, 95% CI 0.28–0.88. Current smoking among the sample is > 50% higher than the adult statewide prevalence. Potential points of intervention identified in this study include perceived ease of worksite smoking breaks and establishing home smoking bans. Tailored cessation efforts focusing on older transit workers more likely to smoke are needed to reduce tobacco-related disparities in this workforce. Keywords: blue-collar workers, health disparities, smoking

Characterization and Health Risk Assessment of Volatile Organic Compounds in Gas Service Station Workers

Directory of Open Access Journals (Sweden)

Duangduan Yimrungruang

2008-07-01

Full Text Available Gas service station workers who work near volatile organic compounds (VOCs sources, such as gasoline vapor emissions, and motor vehicle exhausts, may be exposed to highly elevated VOCs levels. This study investigates air samples from gas service stations in Thailand to evaluate the health risks following inhalation exposure. Personal air samplings were obtained at nine gas service stations in Chonburi, Thailand from October to December 2007. The concentrations of benzene, toluene, ethylbenzene, xylenes, and hexane in the air from the workplaces were significantly higher than in a control group of office workers (p<0.05. However, all VOCs in these air samples were lower than TWA limit of Thailand and the OSHA standard. Samples of urine, collected after 8-h work periods which were analyzed for VOCs metabolites, including t,t muconic acid, hippuric acid, mandelic acid and m-hippuric acid, demonstrate that the average levels of metabolites in gas service station workers and in controls were close, except for t,t muconic acid of gas service station workers which displayed higher levels than the in the controls. The lifetime cancer and noncancer risks for the workers exposed to VOCs were also assessed. Results show that all nine gas service stations in this study had a elevated lifetime cancer risk ranging from 53 to 630 per million, thus exceeding the normal risk of 1 per million. For noncancer risks, the levels in all gas stations ranged between 0.03 and 0.4, which is well below the reference hazard level of 1.0. Benzene may the most important cause of both cancer and noncancer risk followed by 1,3 butadiene.

Cycling-induced degradation of LiCoO{sub 2} thin-film cathodes at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Van Sluytman, J.S.; Alamgir, F.M.; Greenbaum, S.G. [Department of Physics and Astronomy, Hunter College of the City University of New York, 695 Park Avenue, New York, NY 10021 (United States); West, W.C.; Whitacre, J.F. [Electrochemical Technologies Group, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States)

2006-04-01

The cycle life of LiCoO{sub 2}-based all solid-state thin-film cells has been studied at room temperature, and at elevated temperatures of 50, 100, and 150{sup o}C. X-ray diffraction, as well as Raman analysis, has been used to complement the electrochemical data in examining structural and chemical changes. XRD and Raman spectroscopy data indicate that elevated temperature soaks of the thin-film batteries in the quiescent state causes no discernible changes in the LiCoO{sub 2} cathode layer. However, when the thin-film batteries are cycled at elevated temperatures, decreases in average grain size of the LiCoO{sub 2} film occur with dramatic concomitant charge and discharge capacity loss. (author)

Deformation Behavior of a Coarse-Grained Mg-8Al-1.5Ca-0.2Sr Magnesium Alloy at Elevated Temperatures

Science.gov (United States)

Lou, Yan; Liu, Xiao

2018-02-01

The compression tests were carried out on a coarse-grained Mg-8Al-1.5Ca-0.2Sr magnesium alloy samples at temperatures from 300 to 450 °C and strain rates from 0.001 to 10 s-1. The flow stress curves were analyzed using the double-differentiation method, and double minima were detected on the flow curves. The first set of minima is shown to identify the critical strain for twinning, while the second set indicates the critical strain for the initiation of dynamic recrystallization (DRX). Twin variant selection was numerically identified by comprehensive analysis of the Schmid factors for different deformation modes and the accommodation strains imposed on neighboring grains. It was found that twinning is initiated before DRX. Dynamic recrystallization volume increases with strain rate at a given deformation temperature. At high strain rate, various twin variants are activated to accommodate deformation, leading to the formation of twin intersections and high DRX volume. Fully dynamic recrystallized structure can be obtained at both high and low strain rates due to the high mobility of the grain and twin boundaries at the temperature of 400 °C.

Elevating your elevator talk

Science.gov (United States)

An important and often overlooked item that every early career researcher needs to do is compose an elevator talk. The elevator talk, named because the talk should not last longer than an average elevator ride (30 to 60 seconds), is an effective method to present your research and yourself in a clea...

Methods of assessing grain-size distribution during grain growth

DEFF Research Database (Denmark)

Tweed, Cherry J.; Hansen, Niels; Ralph, Brian

1985-01-01

This paper considers methods of obtaining grain-size distributions and ways of describing them. In order to collect statistically useful amounts of data, an automatic image analyzer is used, and the resulting data are subjected to a series of tests that evaluate the differences between two related...... distributions (before and after grain growth). The distributions are measured from two-dimensional sections, and both the data and the corresponding true three-dimensional grain-size distributions (obtained by stereological analysis) are collected. The techniques described here are illustrated by reference...

Grain boundary structure and properties

International Nuclear Information System (INIS)

Balluffi, R.W.

1979-01-01

An attempt is made to distinguish those fundamental aspects of grain boundaries which should be relevant to the problem of the time dependent fracture of high temperature structural materials. These include the basic phenomena which are thought to be associated with cavitation and cracking at grain boundaries during service and with the more general microstructural changes which occur during both processing and service. A very brief discussion of the current state of our knowledge of these fundamentals is given. Included are the following: (1) structure of ideal perfect boundaries; (2) defect structure of grain boundaries; (3) diffusion at grain boundaries; (4) grain boundaries as sources/sinks for point defects; (5) grain boundary migration; (6) dislocation phenomena at grain boundaries; (7) atomic bonding and cohesion at grain boundaries; (8) non-equilibrium properties of grain boundaries; and (9) techniques for studying grain boundaries

Demands for improvement in working surroundings for older workers in nuclear power plants

International Nuclear Information System (INIS)

Shizawa, Yasuhiro; Sakuda, Hiroshi; Ohashi, Tomoki

2003-01-01

Workers in three nuclear power plants belonging to Kansai Electric Power Co., Inc. were asked to complete a questionnaire. According to the accident reports, workers aged 50 or older had more accidents than those in 30s or 40s. Moreover, it is predicted that the average age of workers in Japan will increase during the first half of the 21st century. Therefore, investigations into working surroundings in which older workers can better perform their work would be useful. To this end, a questionnaire addressing issues related to working surroundings was conducted among workers in nuclear power plants and the demands for improvement of working surroundings for older workers are summarized. The demands of 'better lighting', 'making things less heavy', and installation of an elevator' were correlated with age, indicating that younger people have a tendency not to notice these issues. Thus, if the authority deciding on improvements in working surroundings is not an older worker, it is especially important that lighting, the weights of objects to be moved, and methods of moving between floors is taken into account. Findings specific to nuclear power plants were also reported. For example, employees who worked in the non-radiation controlled area demanded the installation of air conditioning and those who worked in the radiation controlled area demanded the establishment of a rest area. Further, we have developed a guidebook entitled 'a guidebook supporting workers' cooperation among all generations' to promote cooperation between older and younger workers. (author)

Interstellar grains

Energy Technology Data Exchange (ETDEWEB)

Hoyle, F.; Wickramasinghe, N.C.

1980-11-01

Interstellar extinction of starlight was observed and plotted as a function of inverse wavelength. Agreement with the calculated effects of the particle distribution is shown. The main kinds of grain distinguished are: (1) graphite spheres of radius 0.02 microns, making up 10% of the total grain mass (2) small dielectric spheres of radius 0.04 microns making up 25% and (3) hollow dielectric cylinders containing metallic iron, with diameters of 2/3 microns making up 45%. The remaining 20% consists of other metals, metal oxides, and polysiloxanes. Absorption factor evidence suggests that the main dielectric component of the grains is organic material.

Reproductive performance of reindeer fed all-grain and hay-grain rations

Directory of Open Access Journals (Sweden)

J. M. Blanchard

1986-06-01

Full Text Available Reproductive performance of grain-fed reindeer {Rangifer tarandus was evaluated over a 2-year period. Groups of pregnant reindeer were fed one of three rations, (1 100% whole-grain barley, (2 98.9% whole-grain barley and 1.2% mineral and trace element supplement, and (3 70% whole-grain barley and 30% finely-chopped bluegrass hay. Reindeer fed unsupplemented whole-barley failed to produce a single live calf. The addition of mineral and trace element supplement to the ration did not result in any significant improvement in reproductive performance. Eighty-five percent of the reindeer consuming unsupplemented and supplemented all-barley rations became pregnant; however, 76% of the pregnancies resulted in stillborn calves. One-hundred percent of the cows maintained on the grain/hay ration produced live calves. We speculate that reproductive failure in reindeer cows maintained on all-grain rations is most likely a result of a diet induced disfunction in maternal rumen and/or carbohydrate metabolism rather than a micro-nutrient deficiency. More research is neeeded to determine which metabolic pathways are affected.

Why do interstellar grains exist

International Nuclear Information System (INIS)

Seab, C.G.; Hollenbach, D.J.; Mckee, C.F.; Tielens, A.G.G.M.

1986-01-01

There exists a discrepancy between calculated destruction rates of grains in the interstellar medium and postulated sources of new grains. This problem was examined by modelling the global life cycle of grains in the galaxy. The model includes: grain destruction due to supernovae shock waves; grain injection from cool stars, planetary nebulae, star formation, novae, and supernovae; grain growth by accretion in dark clouds; and a mixing scheme between phases of the interstellar medium. Grain growth in molecular clouds is considered as a mechanism or increasing the formation rate. To decrease the shock destruction rate, several new physical processes, such as partial vaporization effects in grain-grain collisions, breakdown of the small Larmor radius approximation for betatron acceleration, and relaxation of the steady-state shock assumption are included

Microstructure and mechanical behaviour of an elevated temperature Mg-rare earth based alloy

Energy Technology Data Exchange (ETDEWEB)

Bettles, C.J. [ARC Centre of Excellence for Design in Light Metals, Department of Materials Engineering, Monash University, Clayton 3800, Vic. (Australia); CAST CRC, CSIRO Materials Science and Engineering, Private Bag 33, Clayton South MDC, Clayton 3169, Vic. (Australia)], E-mail: colleen.bettles@eng.monash.edu.au; Gibson, M.A. [CAST CRC, CSIRO Materials Science and Engineering, Private Bag 33, Clayton South MDC, Clayton 3169, Vic. (Australia); Zhu, S.M. [CAST CRC, Department of Materials Engineering, Monash University, Clayton 3800, Vic. (Australia)

2009-04-15

AM-SC1 is a heat treatable magnesium alloy that has been specifically developed to achieve the elevated temperature strength and creep properties necessary for engine block applications. This paper describes the interrelationship between the microstructure and the mechanical properties of AM-SC1. The compressive and tensile strengths are relatively insensitive to temperature up to and including 450 K and the tensile yield behaviour deviates from a standard Hall-Petch relationship at grain sizes below 200 {mu}m. The microstructural features contributing to the creep resistance are both inter- and intra-granular in nature and are on length scales from nanometers to micrometers. The creep behaviour at 423 K and 450 K is diffusion controlled, with any contribution from the grain boundaries being negligible.

The effects of work organization on the health of immigrant manual workers: A longitudinal analysis.

Science.gov (United States)

Arcury, Thomas A; Chen, Haiying; Mora, Dana C; Walker, Francis O; Cartwright, Michael S; Quandt, Sara A

2016-01-01

This analysis uses a longitudinal design to examine the associations of work organization and health outcomes among Latino manual workers. Participants included 247 Latino workers who completed baseline and 1-year follow-up interviews and clinical examinations. Health outcome measures were epicondylitis, rotator cuff syndrome, back pain, and depressive symptoms. Independent measures were measures of job demand, job control, and job support. Workers commonly experienced rotator cuff syndrome (6.5%), back pain (8.9%), and depressive symptoms (11.2%); fewer experienced epicondylitis (2.4%). Psychological demand was associated with rotator cuff syndrome; awkward position and decision latitude were associated with back pain. Decreased skill variety but increased decision latitude was associated with elevated depressive symptoms. Work context factors are important for health outcomes among vulnerable workers. Further research is needed to expand upon this work, particularly cultural perspectives on job support.

Evolution of grain boundary character distributions in alloy 825 tubes during high temperature annealing: Is grain boundary engineering achieved through recrystallization or grain growth?

International Nuclear Information System (INIS)

Bai, Qin; Zhao, Qing; Xia, Shuang; Wang, Baoshun; Zhou, Bangxin; Su, Cheng

2017-01-01

Grain boundary engineering (GBE) of nickel-based alloy 825 tubes was carried out with different cold drawing deformations by using a draw-bench on a factory production line and subsequent annealing at various temperatures. The microstructure evolution of alloy 825 during thermal-mechanical processing (TMP) was characterized by means of the electron backscatter diffraction (EBSD) technique to study the TMP effects on the grain boundary network and the evolution of grain boundary character distributions during high temperature annealing. The results showed that the proportion of ∑ 3 n coincidence site lattice (CSL) boundaries of alloy 825 tubes could be increased to > 75% by the TMP of 5% cold drawing and subsequent annealing at 1050 °C for 10 min. The microstructures of the partially recrystallized samples and the fully recrystallized samples suggested that the proportion of low ∑ CSL grain boundaries depended on the annealing time. The frequency of low ∑ CSL grain boundaries increases rapidly with increasing annealing time associating with the formation of large-size highly-twinned grains-cluster microstructure during recrystallization. However, upon further increasing annealing time, the frequency of low ∑ CSL grain boundaries decreased markedly during grain growth. So it is concluded that grain boundary engineering is achieved through recrystallization rather than grain growth. - Highlights: •The grain boundary engineering (GBE) is applicable to 825 tubes. •GBE is achieved through recrystallization rather than grain growth. •The low ∑ CSL grain boundaries in 825 tubes can be increased to > 75%.

Radium dial workers

International Nuclear Information System (INIS)

Rowland, R.E.; Lucas, H.F. Jr.

1982-01-01

The population of radium dial workers who were exposed to radium 30 to 50 years ago are currently being followed by the Center for Human Radiobiology at the Argonne National Laboratory. It is not clear that radium has induced additional malignancies in this population, other than the well-known bone sarcomas and head carcinomas, but elevated incidence rates for multiple myeloma and cancers of the colon, rectum, stomach, and breast suggest that radium might be involved. Continued follow-up of this population may resolve these questions. Finally, the question of the effect of fetal irradiation on the offspring of these women remains to be resolved. No evidence exists to suggest that any effects have occurred, but there is no question that a chronic irradiation of the developing fetus did take place. No formal follow-up of these children has yet been initiated

Crystallographic and morphological relationships between β phase and the Widmanstaetten and allotriomorphic α phase at special β grain boundaries in an α/β titanium alloy

International Nuclear Information System (INIS)

Bhattacharyya, D.; Viswanathan, G.B.; Fraser, Hamish L.

2007-01-01

In the present study, the relationship between the crystallographic orientations and growth directions of grain boundary-allotriomorphic-α (GB α) and secondary Widmanstaetten α laths growing from the GB α at grain boundaries separating β grains with specific misorientations has been examined. These relationships have been determined using a variety of characterization techniques, including scanning electron microscopy, orientation imaging microscopy, transmission electron microscopy (TEM) and a dual-beam focused ion beam instrument to provide site-selected TEM foils. Two very interesting cases, one in which the two adjacent β grains are rotated mutually by approximately 10.5 o about a common direction and the other in which the two β grains are in a twin relationship, i.e. a 60 o rotation about a common direction, have been studied. It was discovered that the α laths growing into two adjacent β grains from the common grain boundary may have the same orientation in both grains, while they may have either large (∼88.8 o ) or small (28.8 o ) angular differences in growth directions in the two adjacent β grains, depending on the relative misorientation of the β grains. The growth directions of the α laths growing from such boundaries are explained on the basis of the Burgers orientation relationship between the Widmanstaetten α and the β phases and the interfacial structure proposed previously by various workers

Telephone Crisis Support Workers' Intentions to Use Recommended Skills While Experiencing Functional Impairment.

Science.gov (United States)

Kitchingman, Taneile A; Wilson, Coralie J; Woodward, Alan; Caputi, Peter; Wilson, Ian

2018-05-01

Empathic engagement with distressed others can lead to elevated symptoms of psychological distress and functional impairment, which preclude helping professionals' delivery of optimal patient care. Whether telephone crisis support workers are impacted in a similar way is not currently reported in the literature. This study examined the relationship between functional impairment and intentions to use recommended support skills in a representative national sample of 210 telephone crisis support workers. Participants completed an online survey including measures of functional impairment and intentions to use recommended telephone crisis support skills with callers reporting suicidal ideation, symptoms of depression, and anxiety. As a group, participants who experienced greater functional impairment during the past month reported significantly lower intentions to use recommended support skills with callers than those who reported lower functional impairment. Future research is needed to clarify the extent to which results generalize to telephone crisis support workers from other organizations. Results warrant further research to (a) identify determinants of telephone crisis support workers' functional impairment, and (b) for the deliberate management of telephone crisis support workers' functional impairment through developing and/or modifying existing service strategies to optimize workers' psychological well-being and delivery of support to callers.

Lead exposure in radiator repair workers: a survey of Washington State radiator repair shops and review of occupational lead exposure registry data.

Science.gov (United States)

Whittaker, Stephen G

2003-07-01

Radiator repair workers in Washington State have the greatest number of very elevated (> or =60 microg/dL) blood lead levels of any other worker population. The goals of this study were to determine the number of radiator repair workers potentially exposed to lead; estimate the extent of blood lead data underreporting to the Occupational Lead Exposure Registry; describe current safety and health practices in radiator repair shops; and determine appropriate intervention strategies to reduce exposure and increase employer and worker awareness. Lead exposure in Washington State's radiator repair workers was assessed by reviewing Registry data and conducting a statewide survey of radiator repair businesses. This study revealed that a total of 226 workers in Washington State (including owner-operators and all employees) conduct repair activities that could potentially result in excessive exposures to lead. Approximately 26% of radiator repair workers with elevated blood lead levels (> or =25 microg/dL) were determined to report to Washington State's Registry. This study also revealed a lack of awareness of lead's health effects, appropriate industrial hygiene controls, and the requirements of the Lead Standard. Survey respondents requested information on a variety of workplace health and safety issues and waste management; 80% requested a confidential, free-of-charge consultation. Combining data derived from an occupational health surveillance system and a statewide mail survey proved effective at characterizing lead exposures and directing public health intervention in Washington State.

Low cycle fatigue behavior of Sanicro25 steel at room and at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Polák, Jaroslav, E-mail: polak@ipm.cz [Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Žižkova 22, 616 62 Brno (Czech Republic); CEITEC, Institute of Physics of Materials Academy of Sciences of the Czech Republic, Žižkova 22, Brno (Czech Republic); Petráš, Roman; Heczko, Milan; Kuběna, Ivo [Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Žižkova 22, 616 62 Brno (Czech Republic); Kruml, Tomáš [Institute of Physics of Materials, Academy of Sciences of the Czech Republic, Žižkova 22, 616 62 Brno (Czech Republic); CEITEC, Institute of Physics of Materials Academy of Sciences of the Czech Republic, Žižkova 22, Brno (Czech Republic); Chai, Guocai [Sandvik Materials Technology, SE-811 81 Sandviken (Sweden); Linköping University, Engineering Materials, SE-581 83 Linköping (Sweden)

2014-10-06

Austenitic heat resistant Sanicro 25 steel developed for high temperature applications in power generation industry has been subjected to strain controlled low cycle fatigue tests at ambient and at elevated temperature in a wide interval of strain amplitudes. Fatigue hardening/softening curves, cyclic stress–strain curves and fatigue life curves were evaluated at room temperature and at 700 °C. The internal dislocation structures of the material at room and at elevated temperature were studied using transmission electron microscopy. High resolution surface observations and FIB cuts revealed early damage at room temperature in the form of persistent slip bands and at elevated temperature as oxidized grain boundary cracks. Dislocation arrangement study and surface observations were used to identify the cyclic slip localization and to discuss the fatigue softening/hardening behavior and the temperature dependence of the fatigue life.

The temporal and species dynamics of photosynthetic acclimation in flag leaves of rice (Oryza sativa) and wheat (Triticum aestivum) under elevated carbon dioxide

Energy Technology Data Exchange (ETDEWEB)

Zhu, J.; Zeng, Q.; Xie, Z.; Tang, H.; Zhu, C. (Chinese Academy of Sciences. State Key Lab. of Soil and Sustainable Agriculture, Institute of Soil Science, Nanjing (China)); Hasegawa, T. (National Institute for Agro-Environmental Sciences. Agro-Meteorology Div., Tsukuba (Japan)); Ziska, L. (Crop Systems and Global Change Lab., Beltsville, MD (United States)); Jia, X. (Chinese Academic of Sciences/Nanjing Botanical Garden Memorial Sun Yat-Sen. Jiangsu Institute of Botany, Nanjing (China))

2012-07-15

In this study, we tested for the temporal occurrence of photosynthetic acclimation to elevated [CO{sub 2}] in the flag leaf of two important cereal crops, rice and wheat. In order to characterize the temporal onset of acclimation and the basis for any observed decline in photosynthetic rate, we characterized net photosynthesis, g{sub s}, g{sub m}, C{sub i}/C{sub a}, C{sub i}/C{sub c}, V{sub cmax}, J{sub max}, cell wall thickness, content of Rubisco, cytochrome (Cyt) f, N, chlorophyll and carbohydrate, mRNA expression for rbcL and petA, activity for Rubisco, sucrose phosphate synthase (SPS) and sucrose synthase (SS) at full flag expansion, mid-anthesis and the late grain-filling stage. No acclimation was observed for either crop at full flag leaf expansion. However, at the mid-anthesis stage, photosynthetic acclimation in rice was associated with RuBP carboxylation and regeneration limitations, while wheat only had the carboxylation limitation. By grain maturation, the decline of Rubisco content and activity had contributed to RuBP carboxylation limitation of photosynthesis in both crops at elevated [CO{sub 2}]; however, the sharp decrease of Rubisco enzyme activity played a more important role in wheat. Although an increase in non-structural carbohydrates did occur during these later stages, it was not consistently associated with changes in SPS and SS or photosynthetic acclimation. Rather, over time elevated [CO{sub 2}] appeared to enhance the rate of N degradation and senescence so that by late-grain fill, photosynthetic acclimation to elevated [CO{sub 2}] in the flag leaf of either species was complete. These data suggest that the basis for photosynthetic acclimation with elevated [CO{sub 2}] may be more closely associated with enhanced rates of senescence, and, as a consequence, may be temporally dynamic, with significant species variation. (Author)

Effects of grain size and grain boundaries on defect production in nanocrystalline 3C-SiC

International Nuclear Information System (INIS)

Swaminathan, N.; Kamenski, Paul J.; Morgan, Dane; Szlufarska, Izabela

2010-01-01

Cascade simulations in single crystal and nanocrystalline SiC have been conducted in order to determine the role of grain boundaries and grain size on defect production during primary radiation damage. Cascades are performed with 4 and 10 keV silicon as the primary knock-on atom (PKA). Total defect production is found to increase with decreasing grain size, and this effect is shown to be due to increased production in grain boundaries and changing grain boundary volume fraction. In order to consider in-grain defect production, a new mapping methodology is developed to properly normalize in-grain defect production rates for nanocrystalline materials. It is shown that the presence of grain boundaries does not affect the total normalized in-grain defect production significantly (the changes are lower than ∼20%) for the PKA energies considered. Defect production in the single grain containing the PKA is also studied and found to increase for smaller grain sizes. In particular, for smaller grain sizes the defect production decreases with increasing distance from the grain boundary while for larger grain sizes the presence of the grain boundaries has negligible effect on defect production. The results suggest that experimentally observed changes in radiation resistance of nanocrystalline materials may be due to long-term damage evolution rather than changes in defect production rates from primary damage.

Grain growth behavior of Cr dispersed UO{sub 2} pellets according to change of oxygen potential during the isothermal sintering

Energy Technology Data Exchange (ETDEWEB)

Oh, Jang Soo; Yang, Jae Ho; Kim, Dong Joo; Kim, Jong Hun; Nam, Ik Hui; Rhee, Young Woo; Kim, Keon Sik [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-10-15

Recent development of advanced UO{sub 2} pellet materials for commercial reactors is mainly focused on the large grain pellet which can deform easily at an elevated temperature. Cr{sub 2}O{sub 3}-doped UO{sub 2} pellet is one of the promising candidates. To increase the grain size effectively, it is important to control the additive content and sintering atmosphere. Relevant research on the Cr{sub 2}O{sub 3} doped UO{sub 2} system revealed that the doped Cr{sub 2}O{sub 3} formed a liquid phase under optimized oxygen potential, and those liquid phases promoted the grain growth. Recent work also showed that step-wise variation of sintering atmosphere during the isothermal annealing step significantly increased the grain size of Cr{sub 2}O{sub 3} doped UO{sub 2} pellet. In this paper, we investigated effect of oxygen potential change at the beginning of isothermal sintering stage on the grain growth in metallic Cr dispersed UO{sub 2} pellets. The study on the milling effect of powder mixture on the grain growth is also a part of this work.

Occupational exposure levels of bioaerosol components are associated with serum levels of the acute phase protein Serum Amyloid A in greenhouse workers

DEFF Research Database (Denmark)

Madsen, Anne Mette; Thilsing, Trine; Bælum, Jesper

2016-01-01

to elevated levels of bioaerosols. The objective of this study is to assess whether greenhouse workers personal exposure to bioaerosol components was associated with serum levels of the acute phase proteins Serum Amyloid A (SAA) and C-reactive protein (CRP). METHODS: SAA and CRP levels were determined......-glucan. RESULTS: Serum levels of SAA and CRP were not significantly different in greenhouse workers and a reference group, or on the two work days. In a mixed model, SAA levels were positively associated with endotoxin exposure levels (p = 0.0007). Results for fungi were not clear. CRP levels were positively...... associated with endotoxin exposures (p = 0.022). Furthermore, when workers were categorized into three groups based on SAA and CRP serum levels endotoxin exposure was highest in the group with the highest SAA levels and in the group with middle and highest CRP levels. SAA and CRP levels were elevated...

Tailoring Grain Storage Reserves for a Healthier Rice Diet and its Comparative Status with Other Cereals.

Science.gov (United States)

Butardo, Vito M; Sreenivasulu, Nese

2016-01-01

A global rise of diet-related noncommunicable diseases calls for a focus on diet-based nutritional intervention across the entire socioeconomic consumer spectrum. We review recent reports in the area of healthier rice aimed at developing rice grains with improved dietary fiber compositions (increased amounts of nonstarch polysaccharides and resistant starch), and less digestible starch (higher amylose and phospholipid complex in the endosperm) resulting in reduced glycemic impact upon grain consumption. We furthermore elaborate on the interconnections of elevated amounts of protein and a balanced composition of essential amino acids. The importance of a nutritious aleurone layer and its role in lipid storage and micronutrient composition is discussed briefly in the context of brown rice benefits. We identify gene targets for precision breeding that will facilitate the production of rice grains and rice-based products to mitigate the impact of nutrition-related preventable diseases. Copyright © 2016 Elsevier Inc. All rights reserved.

Grain centre mapping - 3DXRD measurements of average grain characteristics

DEFF Research Database (Denmark)

Oddershede, Jette; Schmidt, Søren; Lyckegaard, Allan

2014-01-01

characteristics of each grain (such as their centre-of-mass positions, volumes, phases, orientations and/or elastic strain tensor components), while the exact locations of the grain boundaries are unknown. In the present chapter a detailed description of the setup and software for both grain centre mapping...... and the closely related boxscan method is given. Both validation experiments and applications for in situ studies of microstructural changes during plastic deformation and crack growth are given. Finally an outlook with special emphasis on coupling the measured results with modelling is given....

Grain Boundary Segregation in Metals

CERN Document Server

Lejcek, Pavel

2010-01-01

Grain boundaries are important structural components of polycrystalline materials used in the vast majority of technical applications. Because grain boundaries form a continuous network throughout such materials, their properties may limit their practical use. One of the serious phenomena which evoke these limitations is the grain boundary segregation of impurities. It results in the loss of grain boundary cohesion and consequently, in brittle fracture of the materials. The current book deals with fundamentals of grain boundary segregation in metallic materials and its relationship to the grain boundary structure, classification and other materials properties.

Grain boundaries in Ni3Al. 2

International Nuclear Information System (INIS)

Kung, H.; Sass, S.L.

1992-01-01

This paper discusses the dislocation structure of small angle tilt and twist boundaries in ordered Ni 3 Al, with and without boron, investigated using transmission electron microscopy. Dislocation with Burgers vectors that correspond to anti-phase boundary (APB)-coupled superpartials were found in small angle twist boundaries in both boron-free and boron-doped Ni 3 Al, and a small angle tilt boundary in boron-doped Ni 3 Al. The boundary structures are in agreement with theoretical models proposed by Marcinkowski and co-workers. The APB energy determined from the dissociation of the grain boundary dislocations was lower than values reported for isolated APBs in Ni 3 Al. For small angle twist boundaries the presence of boron reduced the APB energy at the interface until it approached zero. This is consistent with the structure of these boundaries containing small regions of increased compositional disorder in the first atomic plane next to the interface

Integrated physiological, biochemical and molecular analysis identifies important traits and mechanisms associated with differential response of rice genotypes to elevated temperature

Directory of Open Access Journals (Sweden)

Boghireddy eSailaja

2015-11-01

Full Text Available In changing climate, heat stress caused by high temperature poses a serious threat to rice cultivation. A multiple organizational analysis at physiological, biochemical and molecular level is required to fully understand the impact of elevated temperature in rice. This study was aimed at deciphering the elevated temperature response in eleven popular and mega rice cultivars widely grown in India. Physiological and biochemical traits specifically membrane thermostability (MTS, antioxidants, and photosynthesis were studied at vegetative and reproductive phases which were used to establish a correlation with grain yield under stress. Several useful traits in different genotypes were identified which will be important resource to develop high temperature tolerant rice cultivars. Interestingly, Nagina22 emerged as best performer in terms of yield as well as expression of physiological and biochemical traits at elevated temperature. It showed lesser relative injury, lesser reduction in chlorophyll content, increased super oxide dismutase, catalase and peroxidase activity, lesser reduction in net photosynthetic rate (PN, high transpiration rate (E and other photosynthetic/ fluorescence parameters contributing to least reduction in spikelet fertility and grain yield at elevated temperature. Further, expression of 14 genes including heat shock transcription factors and heat shock proteins was analyzed in Nagina22 (tolerant and Vandana (susceptible at flowering phase, strengthening the fact that N22 performs better at molecular level also during elevated temperature. This study shows that elevated temperature response is complex and involves multiple biological processes which are needed to be characterized to address the challenges of future climate extreme conditions.

Grain boundary migration

International Nuclear Information System (INIS)

Dimitrov, O.

1975-01-01

Well-established aspects of grain-boundary migration are first briefly reviewed (influences of driving force, temperature, orientation and foreign atoms). Recent developments of the experimental methods and results are then examined, by considering the various driving of resistive forces acting on grain boundaries. Finally, the evolution in the theoretical models of grain-boundary motion is described, on the one hand for ideally pure metals and, on the other hand, in the presence of solute impurity atoms [fr

Phloem Transport Of Arsenic Species From Flag Leaf To Grain During Grain Filling

Science.gov (United States)

Strategies to reduce arsenic (As) in rice grain, below concentrations that represent a serious human health concern, require that the mechanisms of As accumulation within grain be established. Therefore, retranslocation of As species from flag leaves into filling rice grain was ...

Response of wheat growth, grain yield and water use to elevated CO2 under a Free-Air CO2 Enrichment (FACE) experiment and modelling in a semi-arid environment.

Science.gov (United States)

O'Leary, Garry J; Christy, Brendan; Nuttall, James; Huth, Neil; Cammarano, Davide; Stöckle, Claudio; Basso, Bruno; Shcherbak, Iurii; Fitzgerald, Glenn; Luo, Qunying; Farre-Codina, Immaculada; Palta, Jairo; Asseng, Senthold

2014-12-05

The response of wheat crops to elevated CO 2 (eCO 2 ) was measured and modelled with the Australian Grains Free-Air CO 2 Enrichment experiment, located at Horsham, Australia. Treatments included CO 2 by water, N and temperature. The location represents a semi-arid environment with a seasonal VPD of around 0.5 kPa. Over 3 years, the observed mean biomass at anthesis and grain yield ranged from 4200 to 10 200 kg ha -1 and 1600 to 3900 kg ha -1 , respectively, over various sowing times and irrigation regimes. The mean observed response to daytime eCO 2 (from 365 to 550 μmol mol -1 CO 2 ) was relatively consistent for biomass at stem elongation and at anthesis and LAI at anthesis and grain yield with 21%, 23%, 21% and 26%, respectively. Seasonal water use was decreased from 320 to 301 mm (P = 0.10) by eCO 2 , increasing water use efficiency for biomass and yield, 36% and 31%, respectively. The performance of six models (APSIM-Wheat, APSIM-Nwheat, CAT-Wheat, CROPSYST, OLEARY-CONNOR and SALUS) in simulating crop responses to eCO 2 was similar and within or close to the experimental error for accumulated biomass, yield and water use response, despite some variations in early growth and LAI. The primary mechanism of biomass accumulation via radiation use efficiency (RUE) or transpiration efficiency (TE) was not critical to define the overall response to eCO 2 . However, under irrigation, the effect of late sowing on response to eCO 2 to biomass accumulation at DC65 was substantial in the observed data (~40%), but the simulated response was smaller, ranging from 17% to 28%. Simulated response from all six models under no water or nitrogen stress showed similar response to eCO 2 under irrigation, but the differences compared to the dryland treatment were small. Further experimental work on the interactive effects of eCO 2 , water and temperature is required to resolve these model discrepancies. © 2014 John Wiley & Sons Ltd.

High Temperature-Induced Expression of Rice α-Amylases in Developing Endosperm Produces Chalky Grains

Directory of Open Access Journals (Sweden)

Masaru Nakata

2017-12-01

Full Text Available Global warming impairs grain filling in rice and reduces starch accumulation in the endosperm, leading to chalky-appearing grains, which damages their market value. We found previously that high temperature-induced expression of starch-lytic α-amylases during ripening is crucial for grain chalkiness. Because the rice genome carries at least eight functional α-amylase genes, identification of the α-amylase(s that contribute most strongly to the production of chalky grains could accelerate efficient breeding. To identify α-amylase genes responsible for the production of chalky grains, we characterized the histological expression pattern of eight α-amylase genes and the influences of their overexpression on grain appearance and carbohydrate components through a series of experiments with transgenic rice plants. The promoter activity of most α-amylase genes was elevated to various extents at high temperature. Among them, the expression of Amy1A and Amy3C was induced in the internal, especially basal to dorsal, region of developing endosperm, whereas that of Amy3D was confined near the ventral aleurone. These regions coincided with the site of occurrence of chalkiness, which was in clear contrast to conventionally known expression patterns of the enzyme in the scutellum and aleurone during seed germination. Furthermore, overexpression of α-amylase genes, except for Amy3E, in developing endosperm produced various degrees of chalky grains without heat exposure, whereas that of Amy3E yielded normal translucent grains, as was the case in the vector control, even though Amy3E-overexpressing grains contained enhanced α-amylase activities. The weight of the chalky grains was decreased due to reduced amounts of starch, and microscopic observation of the chalky part of these grains revealed that their endosperm consisted of loosely packed round starch granules that had numerous pits on their surface, confirming the hydrolysis of the starch reserve by

Report of test results at USSO grain elevator - 31150 Lespinasse (France). Storage in tight cells under controlled atmosphere

Energy Technology Data Exchange (ETDEWEB)

1989-12-31

Experimental tests have been conducted with a new storage system for grains: disinsectization of weevil infested wheat through carbon dioxide injection and phosphine (PH3) injection; study of the behaviour of moist harvested sunflowers, stored under carbon dioxide before drying; study of the behaviour of very humid harvested corn, stored in confined atmosphere (without addition of CO2) before drying.

Mortality among 24,865 workers exposed to polychlorinated biphenyls (PCBs) in three electrical capacitor manufacturing plants: A ten-year update

Science.gov (United States)

Ruder, Avima M.; Hein, Misty J.; Hopf, Nancy B.; Waters, Martha A.

2015-01-01

The objective of this analysis was to evaluate mortality among a cohort of 24,865 capacitor-manufacturing workers exposed to polychlorinated biphenyls (PCBs) at plants in Indiana, Massachusetts, and New York and followed for mortality through 2008. Cumulative PCB exposure was estimated using plant-specific job-exposure matrices. External comparisons to US and state-specific populations used standardized mortality ratios, adjusted for gender, race, age and calendar year. Among long-term workers employed 3 months or longer, within-cohort comparisons used standardized rate ratios and multivariable Poisson regression modeling. Through 2008, more than one million person-years at risk and 8749 deaths were accrued. Among long-term employees, all-cause and all-cancer mortality were not elevated; of the a priori outcomes assessed only melanoma mortality was elevated. Mortality was elevated for some outcomes of a priori interest among subgroups of long-term workers: all cancer, intestinal cancer and amyotrophic lateral sclerosis (women); melanoma (men); melanoma and brain and nervous system cancer (Indiana plant); and melanoma and multiple myeloma (New York plant). Standardized rates of stomach and uterine cancer and multiple myeloma mortality increased with estimated cumulative PCB exposure. Poisson regression modeling showed significant associations with estimated cumulative PCB exposure for prostate and stomach cancer mortality. For other outcomes of a priori interest – rectal, liver, ovarian, breast, and thyroid cancer, non-Hodgkin lymphoma, Alzheimer disease, and Parkinson disease – neither elevated mortality nor positive associations with PCB exposure were observed. Associations between estimated cumulative PCB exposure and stomach, uterine, and prostate cancer and myeloma mortality confirmed our previous positive findings. PMID:23707056

75 FR 76254 - Official Performance and Procedural Requirements for Grain Weighing Equipment and Related Grain...

Science.gov (United States)

2010-12-08

... DEPARTMENT OF AGRICULTURE Grain Inspection, Packers and Stockyards Administration 7 CFR Part 802 [Docket GIPSA-2010-FGIS-0012] RIN 0580-AB19 Official Performance and Procedural Requirements for Grain Weighing Equipment and Related Grain Handling Systems AGENCY: Grain Inspection, Packers and Stockyards...

78 FR 33224 - Safety Zone; Grain-Shipment and Grain-Shipment Assist Vessels, Columbia and Willamette Rivers

Science.gov (United States)

2013-06-04

... 1625-AA00 Safety Zone; Grain-Shipment and Grain-Shipment Assist Vessels, Columbia and Willamette Rivers... Guard is establishing a temporary safety zone around all inbound and outbound grain-shipment and grain-shipment assist vessels involved in commerce with the Columbia Grain facility on the Willamette River in...

78 FR 57261 - Safety Zone; Grain-Shipment and Grain-Shipment Assist Vessels, Columbia and Willamette Rivers

Science.gov (United States)

2013-09-18

... 1625-AA00 Safety Zone; Grain-Shipment and Grain-Shipment Assist Vessels, Columbia and Willamette Rivers... temporary safety zone around all inbound and outbound grain-shipment and grain-shipment assist vessels involved in commerce with the Columbia Grain facility on the Willamette River in Portland, OR, the United...

Grain destruction in interstellar shocks

International Nuclear Information System (INIS)

Seab, C.G.; Shull, J.M.

1984-01-01

One of the principal methods for removing grains from the Interstellar Medium is to destroy them in shock waves. Previous theoretical studies of shock destruction have generally assumed only a single size and type of grain; most do not account for the effect of the grain destruction on the structure of the shock. Earlier calculations have been improved in three ways: first, by using a ''complete'' grain model including a distribution of sizes and types of grains; second, by using a self-consistent shock structure that incorporates the changing elemental depletions as the grains are destroyed; and third, by calculating the shock-processed ultraviolet extinction curves for comparison with observations. (author)

Urinary neutrophil gelatinase-associated lipocalin is associated with heavy metal exposure in welding workers.

Science.gov (United States)

Chuang, Kai-Jen; Pan, Chih-Hong; Su, Chien-Ling; Lai, Ching-Huang; Lin, Wen-Yi; Ma, Chih-Ming; Ho, Shu-Chuan; Bien, Mauo-Ying; Chen, Cheng-Hsien; Chuang, Hsiao-Chi

2015-12-17

Metals cause nephrotoxicity with acute and/or chronic exposure; however, few epidemiological studies have examined impacts of exposure to metal fumes on renal injury in welding workers. In total, 66 welding workers and 12 office workers were recruited from a shipyard located in southern Taiwan. Urine samples from each subject were collected at the beginning (baseline) and end of the work week (1-week exposure). Personal exposure to PM2.5 was measured. The 8-h mean PM2.5 was 50.3 μg/m(3) for welding workers and 27.4 μg/m(3) for office workers. iTRAQs coupled with LC-MS/MS were used to discover the pathways in response to welding PM2.5 in the urine, suggesting that extracellular matrix (ECM)-receptor interactions are a critical mechanism. ECM-receptor interaction-related biomarkers for renal injury, kidney injury molecule (KIM)-1 and neutrophil gelatinase-associated lipocalin (NGAL), were significantly elevated in welding workers post-exposure, as well as were urinary Al, Cr, Mn, Fe, Co, and Ni levels. NGAL was more significantly associated with Al (r = 0.737, p welding PM2.5 exposure. Nephrotoxicity (e.g., renal tubular injury) may be an emerging concern in occupational health.

Plant Density Effect on Grain Number and Weight of Two Winter Wheat Cultivars at Different Spikelet and Grain Positions

Science.gov (United States)

Ni, Yingli; Zheng, Mengjing; Yang, Dongqing; Jin, Min; Chen, Jin; Wang, Zhenlin; Yin, Yanping

2016-01-01

In winter wheat, grain development is asynchronous. The grain number and grain weight vary significantly at different spikelet and grain positions among wheat cultivars grown at different plant densities. In this study, two winter wheat (Triticum aestivum L.) cultivars, ‘Wennong6’ and ‘Jimai20’, were grown under four different plant densities for two seasons, in order to study the effect of plant density on the grain number and grain weight at different spikelet and grain positions. The results showed that the effects of spikelet and grain positions on grain weight varied with the grain number of spikelets. In both cultivars, the single-grain weight of the basal and middle two-grain spikelets was higher at the 2nd grain position than that at the 1st grain position, while the opposite occurred in the top two-grain spikelets. In the three-grain spikelets, the distribution of the single-grain weight was different between cultivars. In the four-grain spikelets of Wennong6, the single-grain weight was the highest at the 2nd grain position, followed by the 1st, 3rd, and 4th grain positions. Regardless of the spikelet and grain positions, the single-grain weight was the highest at the 1st and 2nd grain positions and the lowest at the 3rd and 4th grain positions. Overall, plant density affected the yield by controlling the seed-setting characteristics of the tiller spike. Therefore, wheat yield can be increased by decreasing the sterile basal and top spikelets and enhancing the grain weight at the 3rd and 4th grain positions, while maintaining it at the 1st and 2nd grain positions on the spikelet. PMID:27171343

Effects of Single and Multifactor Treatments with Elevated Temperature, CO2 and Ozone on Oilseed Rape and Barley

DEFF Research Database (Denmark)

Clausen, Sabine Karin; Frenck, Georg; van der Linden, Leon Gareth

2011-01-01

We investigated the effect of elevated [CO2], [O3] and temperature on plant productivity and if these climate factors interacted with each other in multifactor treatments. The climate effects were studied in 14 different cultivars/lines of European spring oilseed rape (Brassica napus L.) and spring...... barley (Hordeum vulgare L.). Seven genotypes of each species were cultivated in six single- and multifactor treatments with ambient or elevated CO2 (385 ppm and 700 ppm), O3 (20 ppb and 60 ppb) and temperature (12/19 °C and 17/24 °C). Growth and production parameters were measured. Elevated CO2 increased....... A significantly decreased yield and thousand grain weight was also seen in barley due to elevated O3. The multifactor combination of elevated CO2, O3 and temperature showed a decrease in growth and production in the two species, though not statistically significant for all parameters. This trend suggests...

Modelling of grain refinement driven by negative grain boundary energy

Czech Academy of Sciences Publication Activity Database

Fischer, F. D.; Zickler, G. A.; Svoboda, Jiří

2017-01-01

Roč. 97, č. 23 (2017), s. 1963-1977 ISSN 1478-6435 R&D Projects: GA ČR(CZ) GA15-06390S Institutional support: RVO:68081723 Keywords : grain refinement * grain nucleation * distribution concept * jump on distribution function Subject RIV: BJ - Thermodynamics OBOR OECD: Thermodynamics Impact factor: 1.505, year: 2016

Grain Interactions in Crystal Plasticity

International Nuclear Information System (INIS)

Boyle, K.P.; Curtin, W.A.

2005-01-01

The plastic response of a sheet metal is governed by the collective response of the underlying grains. Intragranular plasticity depends on intrinsic variables such as crystallographic orientation and on extrinsic variables such as grain interactions; however, the role of the latter is not well understood. A finite element crystal plasticity formulation is used to investigate the importance of grain interactions on intragranular plastic deformation in initially untextured polycrystalline aggregates. A statistical analysis reveals that grain interactions are of equal (or more) importance for determining the average intragranular deviations from the applied strain as compared to the orientation of the grain itself. Furthermore, the influence of the surrounding grains is found to extend past nearest neighbor interactions. It is concluded that the stochastic nature of the mesoscale environment must be considered for a proper understanding of the plastic response of sheet metals at the grain-scale

Stabilisation of the grain market by the flexible use of grain for bioethanol

NARCIS (Netherlands)

Helming, J.F.M.; Pronk, A.; Woltjer, I.

2010-01-01

This report reviews whether the grain market and grain price can be stabilised by the variation of the use of grain in the EU-27's production of bioethanol. The time horizon of this study is 2020, whereby account is taken of the minimum 10% obligation for biofuel use in the EU-27. An economic

Inter-grain coupling and grain charge in dusty plasma Coulomb crystals

International Nuclear Information System (INIS)

Smith, M. A.; Goodrich, J.; Mohideen, U.; Rahman, H. U.; Rosenberg, M.; Mendis, D. A.

1998-01-01

We have studied the lattice structure and grain charge of dusty plasma Coulomb crystals formed in rectangular conductive grooves as a function of plasma temperature and density. The crystal appears to be made of mutually repulsive columns of grains confined by the walls of the groove. The columns are oriented along the direction of the electrode sheath electric field. A simple phenomenological model wherein the inter-grain spacing results from an attractive electric field induced dipole-dipole force balanced by a repulsive monopole Coulomb force is consistent with observed features of the Coulomb crystal

A constitutive model of nanocrystalline metals based on competing grain boundary and grain interior deformation mechanisms

KAUST Repository

Gurses, Ercan

2011-12-01

In this work, a viscoplastic constitutive model for nanocrystalline metals is presented. The model is based on competing grain boundary and grain interior deformation mechanisms. In particular, inelastic deformations caused by grain boundary diffusion, grain boundary sliding and dislocation activities are considered. Effects of pressure on the grain boundary diffusion and sliding mechanisms are taken into account. Furthermore, the influence of grain size distribution on macroscopic response is studied. The model is shown to capture the fundamental mechanical characteristics of nanocrystalline metals. These include grain size dependence of the strength, i.e., both the traditional and the inverse Hall-Petch effects, the tension-compression asymmetry and the enhanced rate sensitivity. © 2011 Elsevier B.V. All rights reserved.

Mobile Applications for Knowledge Workers and Field Workers

Directory of Open Access Journals (Sweden)

Stefan Stieglitz

2015-01-01

Full Text Available In recent years, the diffusion of mobile applications (mobile apps has risen significantly. Nowadays, mobile business apps are strongly emerging in business, enhancing productivity and employees’ satisfaction, whilst the usage of customized individual enterprise apps is still an exception. Standardized business apps enable basic functionalities, for example, mobile data storage and exchange (e.g., Dropbox, communication (e.g., Skype, and other routine processes, which support mobile workers. In addition, mobile apps can, for example, increase the flexibility of mobile workers by easing the access to firm’s information from outside the enterprise and by enabling ubiquitous collaboration. Hence, mobile apps can generate competitive advantages and can increase work efficiency on a broad scale. But mobile workers form no coherent group. Our research reveals, based on two case studies, that they can be clustered into two groups: knowledge workers and field workers. Knowledge workers and field workers fulfill different tasks and work in different environments. Hence, they have different requirements for mobile support. In this paper we conclude that standardized mobile business apps cannot meet the different requirements of various groups of mobile workers. Task- and firm-specific (individualized requirements determine the specification, implementation, and application of mobile apps.

Photoelectric charging of dust grains

International Nuclear Information System (INIS)

Ignatov, A. M.

2009-01-01

Photoemission from the surface of a dust grain in vacuum is considered. It is shown that the cutoff in the energy spectrum of emitted electrons leads to the formation of a steady-state electron cloud. The equation describing the distribution of the electric potential in the vicinity of a dust grain is solved numerically. The dust grain charge is found as a function of the grain size.

Grain Flow at High Stresses

Science.gov (United States)

McSaveney, M. J.

2015-12-01

The transport mechanism of rapid long-runout rock avalanches was a hotly debated topic when I came on the scene in 1967. So how come it is still debated today? My explanation is that it is the expected outcome of peer review, poor comprehension, and technological advances outpacing intellectual advances. Why think about the problem when we can model it! So let us think about the problem. Shreve thought that rock avalanches fell upon and trapped a layer of air. What physics was he thinking about? It is how feathers and tissue papers fall. When my rock avalanches fly, they fly like unlubricated bricks using the physics of projectiles and ballistics. But the main transport mechanism is not flight. The dominant impression from watching a rock avalanche in motion is of fluid flow, as Heim described it in 1882. A rock avalanche is a very large grain flow. Bagnold studied dispersive grain flows, but why should one assume that rock avalanches are dispersive grain flows as many do. The more common grain flow type is a dense grain flow and rock avalanches are dense grain flows in which the weight can and does generate very high stresses at grain contacts. Brittle rock deforms elastically up to its compressive strength, whereupon it breaks, releasing elastic strain as transient elastic strain (seismic energy to a seismologist, acoustic energy to a physicist). Melosh and others have shown that acoustic energy can fluidize a grain mass. There is no exotic physics behind grain flow at high stress. When grains break, the released elastic strain has to go somewhere, and it goes somewhere principally by transmission though grain contacts. Depending on the state of stress at the grain contact, the contact will pass the stress or will slip at conventional values of Coulomb friction. Enough thinking! A physical model of the entire process is too big for any laboratory. So whose numerical model will do it?

Impact fracture experiments simulating interstellar grain-grain collisions

Science.gov (United States)

Freund, Friedemann; Chang, Sherwood; Dickinson, J. Thomas

1990-01-01

Oxide and silicate grains condensing during the early phases of the formation of the solar system or in the outflow of stars are exposed to high partial pressures of the low-z elements H, C, N and O and their simple gaseous compounds. Though refractory minerals are nominally anhydrous and non-carbonate, if they crystallize in the presence of H2O, N2 and CO or CO2 gases, they dissolve traces of the gaseous components. The question arises: How does the presence of dissolved gases or gas components manifest itself when grain-grain collisions occur. What are the gases emitted when grains are shattered during a collision event. Researchers report on fracture experiments in ultrahigh vacuum (UHV, approximately less than 10 to the -8th power mbar) designed to measure (by means of a quadrupole mass spectrometer, QMS, with microns to ms time resolution) the emission of gases and vapors during and after impact (up to 1.5 sec). Two terrestrial materials were chosen which represent structural and compositional extremes: olivine (San Carlos, AZ), a densely packed Mg-Fe(2+) silicate from the upper mantle, available as 6 to 12 mm single crystals, and obsidian (Oregon), a structurally open, alkaline-SiO2-rich volcanic glass. In the olivine crystals OH- groups have been identified spectroscopically, as well as H2 molecules. Obsidian is a water-rich glass containing OH- besides H2O molecules. Olivine from the mantle often contains CO2, either as CO2-rich fluid in fluid inclusions or structurally dissolved or both. By analogy to synthetic glasses CO2 in the obsidian may be present in form of CO2 molecules in voids of molecular dimensions, or as carbonate anions, CO3(2-). No organic molecules have been detected spectroscopically in either material. Results indicate that refractory oxide/silicates which contain dissolved traces of the H2O and CO/CO2 components but no spectroscopically detectable traces of organics may release complex H-C-O (possibly H-C-N-O) molecules upon fracture

Microbiota of kefir grains

OpenAIRE

Tomislav Pogačić; Sanja Šinko; Šimun Zamberlin; Dubravka Samaržija

2013-01-01

Kefir grains represent the unique microbial community consisting of bacteria, yeasts, and sometimes filamentous moulds creating complex symbiotic community. The complexity of their physical and microbial structures is the reason that the kefir grains are still not unequivocally elucidated. Microbiota of kefir grains has been studied by many microbiological and molecular approaches. The development of metagenomics, based on the identification without cultivation, is opening new possibilities f...

Interplay between grain structure and protein adsorption on functional response of osteoblasts: ultrafine-grained versus coarse-grained substrates.

Science.gov (United States)

Misra, R D K; Nune, C; Pesacreta, T C; Somani, M C; Karjalainen, L P

2013-01-01

The rapid adsorption of proteins is the starting and primary biological response that occurs when a biomedical device is implanted in the physiological system. The biological response, however, depends on the surface characteristics of the device. Considering the significant interest in nano-/ultrafine surfaces and nanostructured coatings, we describe here, the interplay between grain structure and protein adsorption (bovine serum albumin: BSA) on osteoblasts functions by comparing nanograined/ultrafine-grained (NG/UFG) and coarse-grained (CG: grain size in the micrometer range) substrates by investigating cell-substrate interactions. The protein adsorption on NG/UFG surface was beneficial in favorably modulating biological functions including cell attachment, proliferation, and viability, whereas the effect was less pronounced on protein adsorbed CG surface. Additionally, immunofluorescence studies demonstrated stronger vinculin signals associated with actin stress fibers in the outer regions of the cells and cellular extensions on protein adsorbed NG/UFG surface. The functional response followed the sequence: NG/UFG(BSA) > NG/UFG > CG(BSA) > CG. The differences in the cellular response on bare and protein adsorbed NG/UFG and CG surfaces are attributed to cumulative contribution of grain structure and degree of hydrophilicity. The study underscores the potential advantages of protein adsorption on artificial biomedical devices to enhance the bioactivity and regulate biological functions. Copyright © 2012 Wiley Periodicals, Inc.

Mortality among 24,865 workers exposed to polychlorinated biphenyls (PCBs) in three electrical capacitor manufacturing plants: a ten-year update.

Science.gov (United States)

Ruder, Avima M; Hein, Misty J; Hopf, Nancy B; Waters, Martha A

2014-03-01

The objective of this analysis was to evaluate mortality among a cohort of 24,865 capacitor-manufacturing workers exposed to polychlorinated biphenyls (PCBs) at plants in Indiana, Massachusetts, and New York and followed for mortality through 2008. Cumulative PCB exposure was estimated using plant-specific job-exposure matrices. External comparisons to US and state-specific populations used standardized mortality ratios, adjusted for gender, race, age and calendar year. Among long-term workers employed 3 months or longer, within-cohort comparisons used standardized rate ratios and multivariable Poisson regression modeling. Through 2008, more than one million person-years at risk and 8749 deaths were accrued. Among long-term employees, all-cause and all-cancer mortality were not elevated; of the a priori outcomes assessed only melanoma mortality was elevated. Mortality was elevated for some outcomes of a priori interest among subgroups of long-term workers: all cancer, intestinal cancer and amyotrophic lateral sclerosis (women); melanoma (men); melanoma and brain and nervous system cancer (Indiana plant); and melanoma and multiple myeloma (New York plant). Standardized rates of stomach and uterine cancer and multiple myeloma mortality increased with estimated cumulative PCB exposure. Poisson regression modeling showed significant associations with estimated cumulative PCB exposure for prostate and stomach cancer mortality. For other outcomes of a priori interest--rectal, liver, ovarian, breast, and thyroid cancer, non-Hodgkin lymphoma, Alzheimer disease, and Parkinson disease--neither elevated mortality nor positive associations with PCB exposure were observed. Associations between estimated cumulative PCB exposure and stomach, uterine, and prostate cancer and myeloma mortality confirmed our previous positive findings. Published by Elsevier GmbH.

Whole grains and health: attitudes to whole grains against a prevailing background of increased marketing and promotion.

Science.gov (United States)

McMackin, Elaine; Dean, Moira; Woodside, Jayne V; McKinley, Michelle C

2013-04-01

To explore current awareness and perceptions of whole grain foods and perceived barriers and facilitators of whole grain consumption. Focus groups were conducted to investigate consumer attitudes to whole grains. Discussions were transcribed verbatim and analysed thematically. Discussions were held throughout Northern Ireland with adults who were at least partly responsible for food shopping. Seven focus groups were held (n 43; thirty-three females, ten males). All participants were aware of the term 'whole grain' and had a basic level of awareness of their health benefits. Prominent barriers and facilitators of whole grain intake were related to perceptions of the sensory properties (most dominant factor) of whole grains; knowledge of how to locate, identify and use whole grains; and awareness of the health benefits, perceived cost and family influences. Parents of young children appeared to be altruistically motivated with many stating they wanted to ensure their children consumed whole grains in order to establish good eating habits. Participants were generally aware of the term 'whole grain'; however, even against a background of increased availability and promotion of whole grain foods, many key barriers to whole grain consumption were still evident. Alongside general education efforts, opportunities and challenges exist for the food industry to develop novel, but affordable, food products that are able to deliver whole grains in a wide variety of forms, including whole grains 'in disguise' for those who are most resistant to change.

Effects of feeding blends of grains naturally contaminated with Fusarium mycotoxins on performance and metabolism of laying hens.

Science.gov (United States)

Chowdhury, S R; Smith, T K

2004-11-01

An experiment was conducted to evaluate the effects of feeding laying hens grains naturally contaminated with a combination of Fusarium mycotoxins. Parameters measured included performance, organ weights, and plasma chemistry. One hundred and forty-four, 45-wk-old laying hens were fed diets including: (1) control, (2) contaminated grains, and (3) contaminated grains + 0.2% polymeric glucomannan mycotoxin adsorbent (GMA) for a 12-wk period. The feeding of contaminated grains decreased feed consumption compared with controls in the first 4 wk. Feed consumption increased, however, from 4 to 8 wk and from 8 to 12 wk. The efficiency of feed utilization (feed consumption/egg mass) decreased compared with controls in the periods from 4 to 8 and from 8 to 12 wk when birds were fed contaminated grains. Supplementation with GMA decreased feed consumption and increased the efficiency of feed utilization in the period from 8 to 12 wk. Egg production and egg mass decreased in wk 4 and 8 compared with controls when contaminated grains were fed, whereas egg and eggshell weights decreased in the fourth wk. Plasma uric acid concentrations increased throughout the experiment and relative kidney weights increased at the end of the experiment compared with controls when birds were fed contaminated grains. The feeding of GMA prevented the elevation in uric acid concentrations and relative kidney weights. It was concluded that layer performance and metabolism were adversely affected by chronic feeding of a combination of Fusarium mycotoxins, and that GMA prevented many of these effects.

Grain boundary and grain interior conduction in {gamma}'-Bi{sub 2}MoO{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Vera, C.M.C. [Laboratorio de Peliculas Delgadas, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, 1063 Buenos Aires (Argentina)]. E-mail: cvera@fi.uba.ar; Aragon, R. [Laboratorio de Peliculas Delgadas, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, 1063 Buenos Aires (Argentina); CINSO, CONICET, CITEFA, Lasalle 4397, Villa Martelli, Buenos Aires (Argentina)

2005-07-25

Impedance spectroscopy of fine grained (<10 {mu}m) {gamma}'-Bi{sub 2}MoO{sub 6} samples, in the frequency range of 0.1 Hz-250 kHz, relevant to sensor applications, up to 800 deg. C, has been used to characterize grain boundary and grain interior contributions to conduction. Above 500 deg. C, the grain boundary contribution is no longer rate limiting and conduction is dominated by the grain interior component. The corresponding activation energies are 0.98 eV for grain boundary and 0.73 eV for grain interior components. The weak dependence of conductivity on oxygen partial pressure below 500 deg. C can be attributed to electrode-electrolyte interface phenomena, whereas the robust response to ethanol is commensurate with changes in intrinsic ionic conductivity.

Should Workers Avoid Consumption of Chilled Fluids in a Hot and Humid Climate?

Directory of Open Access Journals (Sweden)

Matt B. Brearley

2017-12-01

Full Text Available Despite provision of drinking water as the most common method of occupational heat stress prevention, there remains confusion in hydration messaging to workers. During work site interactions in a hot and humid climate, workers commonly report being informed to consume tepid fluids to accelerate rehydration. When questioned on the evidence supporting such advice, workers typically cite that fluid absorption is delayed by ingestion of chilled beverages. Presumably, delayed absorption would be a product of fluid delivery from the gut to the intestines, otherwise known as gastric emptying. Regulation of gastric emptying is multifactorial, with gastric volume and beverage energy density the primary factors. If gastric emptying is temperature dependent, the impact of cooling is modest in both magnitude and duration (≤ 5 minutes due to the warming of fluids upon ingestion, particularly where workers have elevated core temperature. Given that chilled beverages are most preferred by workers, and result in greater consumption than warm fluids during and following physical activity, the resultant increased consumption of chilled fluids would promote gastric emptying through superior gastric volume. Hence, advising workers to avoid cool/cold fluids during rehydration appears to be a misinterpretation of the research. More appropriate messaging to workers would include the thermal benefits of cool/cold fluid consumption in hot and humid conditions, thereby promoting autonomy to trial chilled beverages and determine personal preference. In doing so, temperature-based palatability would be maximized and increase the likelihood of workers maintaining or restoring hydration status during and after their work shift. Keywords: Fluid consumption, gastric emptying, hot and humid conditions, hydration, occupational

Glutamine Synthetases GLN1;2 and GLN2 in Relation to Arabidopsis Growth Response to Elevated Atmospheric Carbon Dioxide and Varying Nitrogen Forms

DEFF Research Database (Denmark)

Vurrakula, Swathi

content while diluting nitrogen concentrations. Such a reduction in nitrogen concentration will affect plant response to stress and seed/grain yield. Glutamine synthetase (GS) is the central nitrogen-assimilatory enzyme, performing primary and secondary nitrogen assimilation, in response to environmental....... Plants grown under elevated CO2 absorbed ammonia from the atmosphere, except with a high ammonium supply. GLN1;2 had a non-redundant role in determining vegetative growth and ammonium tolerance in response to elevated CO2. Under elevated CO2, GLN1;2 was compensable by GLN2 in assimilating nitrate...

A UNIFIED MODEL OF GRAIN ALIGNMENT: RADIATIVE ALIGNMENT OF INTERSTELLAR GRAINS WITH MAGNETIC INCLUSIONS

Energy Technology Data Exchange (ETDEWEB)

Hoang, Thiem [Canadian Institute for Theoretical Astrophysics, University of Toronto, 60 St. George Street, Toronto, ON M5S 3H8 (Canada); Lazarian, A. [Department of Astronomy, University of Wisconsin-Madison (United States)

2016-11-10

The radiative torque (RAT) alignment of interstellar grains with ordinary paramagnetic susceptibilities has been supported by earlier studies. The alignment of such grains depends on the so-called RAT parameter q {sup max}, which is determined by the grain shape. In this paper, we elaborate on our model of RAT alignment for grains with enhanced magnetic susceptibility due to iron inclusions, such that RAT alignment is magnetically enhanced, which we term the MRAT mechanism. Such grains can be aligned with high angular momentum at the so-called high- J attractor points, achieving a high degree of alignment. Using our analytical model of RATs, we derive the critical value of the magnetic relaxation parameter δ {sub m} to produce high- J attractor points as functions of q {sup max} and the anisotropic radiation angle relative to the magnetic field ψ . We find that if about 10% of the total iron abundance present in silicate grains is forming iron clusters, this is sufficient to produce high- J attractor points for all reasonable values of q {sup max}. To calculate the degree of grain alignment, we carry out numerical simulations of MRAT alignment by including stochastic excitations from gas collisions and magnetic fluctuations. We show that large grains can achieve perfect alignment when the high- J attractor point is present, regardless of the values of q {sup max}. Our obtained results pave the way for the physical modeling of polarized thermal dust emission as well as magnetic dipole emission. We also find that millimeter-sized grains in accretion disks may be aligned with the magnetic field if they are incorporated with iron nanoparticles.

Selection of common bean lines with high grain yield and high grain calcium and iron concentrations

Directory of Open Access Journals (Sweden)

Nerinéia Dalfollo Ribeiro

2014-02-01

Full Text Available Genetic improvement of common bean nutritional quality has advantages in marketing and can contribute to society as a food source. The objective of this study was to evaluate the genetic variability for grain yield, calcium and iron concentrations in grains of inbred common bean lines obtained by different breeding methods. For this, 136 F7 inbred lines were obtained using the Pedigree method and 136 F7 inbred lines were obtained using the Single-Seed Descent (SSD method. The lines showed genetic variability for grain yield, and concentrations of calcium and iron independently of the method of advancing segregating populations. The Pedigree method allows obtaining a greater number of lines with high grain yield. Selection using the SSD method allows the identification of a larger number of lines with high concentrations of calcium and iron in grains. Weak negative correlations were found between grain yield and calcium concentration (r = -0.0994 and grain yield and iron concentration (r = -0.3926. Several lines show genetic superiority for grain yield and concentrations of calcium and iron in grains and their selection can result in new common bean cultivars with high nutritional quality.

Work-related asthma in a population exposed to grain, flour and other ingredient dusts.

Science.gov (United States)

Smith, T A; Lumley, K P

1996-02-01

The purpose of the study was to determine the prevalence and causation of work-related asthmatic symptoms in a population exposed to grain, flour and other ingredient dusts. Where workers complained of asthmatic symptoms which were the result of dust exposure, follow-up aimed to identify whether the symptoms were the result of sensitisation or of non-specific irritation. A questionnaire was presented to 3,450 workers who had exposure to dust during the course of flour milling (528), bread baking (1,756), cake baking (209) and other activities in food preparation (957). Those with positive responses were followed-up by taking a formal history, examination, skin prick testing and serial peak flow measurement. The overall prevalence of work-related asthmatic symptoms was 4.4% (153 out of 3,450). In the group who were followed-up (128 out of 153), non-specific respiratory irritation was thought to be the cause in 90 (2.6%), whilst sensitisation was responsible for symptoms in 12 (0.3%). Of the 12 cases due to sensitisation, the agents responsible were: fungal amylase (10 cases, all associated with bread baking), flour (one case, associated with flour packing), and grain (one case, associated with flour milling). Non-specific irritation is considerably more common than sensitisation as the cause of work-related asthmatic symptoms in flour milling, baking and other flour-based industries. The prevalence of sensitisation to flour is very low (less than 1 in 1,000) in all these industries. The principal sensitiser encountered in modern plant bakeries appears to be fungal amylase. The most important source of exposure to fungal amylase is probably the debagging, sieving, weighing and mixing of bread improvers.

Colorado River sediment transport: 2. Systematic bed‐elevation and grain‐size effects of sand supply limitation

Science.gov (United States)

Topping, David J.; Rubin, David M.; Nelson, Jonathan M.; Kinzel, Paul J.; Corson, Ingrid C.

2000-01-01

The Colorado River in Marble and Grand Canyons displays evidence of annual supply limitation with respect to sand both prior to [Topping et al, this issue] and after the closure of Glen Canyon Dam in 1963. Systematic changes in bed elevation and systematic coupled changes in suspended‐sand concentration and grain size result from this supply limitation. During floods, sand supply limitation either causes or modifies a lag between the time of maximum discharge and the time of either maximum or minimum (depending on reach geometry) bed elevation. If, at a cross section where the bed aggrades with increasing flow, the maximum bed elevation is observed to lead the peak or the receding limb of a flood, then this observed response of the bed is due to sand supply limitation. Sand supply limitation also leads to the systematic evolution of sand grain size (both on the bed and in suspension) in the Colorado River. Sand input during a tributary flood travels down the Colorado River as an elongating sediment wave, with the finest sizes (because of their lower settling velocities) traveling the fastest. As the fine front of a sediment wave arrives at a given location, the bed fines and suspended‐sand concentrations increase in response to the enhanced upstream supply of finer sand. Then, as the front of the sediment wave passes that location, the bed is winnowed and suspended‐sand concentrations decrease in response to the depletion of the upstream supply of finer sand. The grain‐size effects of depletion of the upstream sand supply are most obvious during periods of higher dam releases (e.g., the 1996 flood experiment and the 1997 test flow). Because of substantial changes in the grain‐size distribution of the bed, stable relationships between the discharge of water and sand‐transport rates (i.e., stable sand rating curves) are precluded. Sand budgets in a supply‐limited river like the Colorado River can only be constructed through inclusion of the physical

Kansas Agents Study Grain Marketing

Science.gov (United States)

Schoeff, Robert W.

1973-01-01

Author is an extension specialist in feed and grain marketing for Kansas State University. He describes a tour set up to educate members of the Kansas Grain and Feed Dealers' Association in the area of grain marketing and exporting. (GB)

Advection-diffusion model for normal grain growth and the stagnation of normal grain growth in thin films

International Nuclear Information System (INIS)

Lou, C.

2002-01-01

An advection-diffusion model has been set up to describe normal grain growth. In this model grains are divided into different groups according to their topological classes (number of sides of a grain). Topological transformations are modelled by advective and diffusive flows governed by advective and diffusive coefficients respectively, which are assumed to be proportional to topological classes. The ordinary differential equations governing self-similar time-independent grain size distribution can be derived analytically from continuity equations. It is proved that the time-independent distributions obtained by solving the ordinary differential equations have the same form as the time-dependent distributions obtained by solving the continuity equations. The advection-diffusion model is extended to describe the stagnation of normal grain growth in thin films. Grain boundary grooving prevents grain boundaries from moving, and the correlation between neighbouring grains accelerates the stagnation of normal grain growth. After introducing grain boundary grooving and the correlation between neighbouring grains into the model, the grain size distribution is close to a lognormal distribution, which is usually found in experiments. A vertex computer simulation of normal grain growth has also been carried out to make a cross comparison with the advection-diffusion model. The result from the simulation did not verify the assumption that the advective and diffusive coefficients are proportional to topological classes. Instead, we have observed that topological transformations usually occur on certain topological classes. This suggests that the advection-diffusion model can be improved by making a more realistic assumption on topological transformations. (author)

Post-IR IRSL₂₉₀ dating of K-rich feldspar sand grains in a wind-dominated system on Sardinia

DEFF Research Database (Denmark)

Andreucci, S.; Sechi, D.; Buylaert, Jan-Pieter

2017-01-01

The reliability of a post-IR elevated temperature IRSL (290 °C; pIRIR290) is tested on wind-blown, sand-sized (180–250 μm) K-rich feldspar grains. The pIRIR290 ages were compared with quartz SAR-OSL data, other independent age controls and historical information. Three study areas along the coast....... The pIRIR290 ages indicate an offset up to ∼1000 years. We can conclude that the pIRIR290 method on sand-sized K-feldspar grains shows great promise for samples at or beyond the quartz OSL age limit but should not be applied to Late Holocene or modern deposits....

Chromosome aberrations in workers of beach sand mineral industries

International Nuclear Information System (INIS)

Meenakshi, C.; Mohankumar, Mary N.

2013-01-01

Beach Sand Mining (BSM) is a profitable industry earning a sizable income for the country by way of foreign exchange. The Indian coast is rich in rare earths such as ilmenite, rutile, leucoxene, zircon, garnet and sillimanite, and is invariably associated with radioactive monazite. Due to the nature of the separation processes involved and the manual handling, workers in these factories are continuously being exposed to suspended particles containing naturally occurring radioactive materials. An attempt was made to estimate DNA damage using a chromosome aberration assay to monitor radiation effects in workers of BSM industries in India. The study group comprised 27 BSM workers and 20 controls. Percentage yields of dicentrics, acentric fragments and chromatid breaks observed in the control group were 0.058 ± 0.017, 0.073 ± 0.03 and 0.22 ± 0.112, respectively. Percentage yields of dicentrics + centric rings, acentric fragments and chromatid breaks observed in the BSM group were 0.029 ± 0.01 (P value 0.19), 0.24 ± 0.06 (P value 0.006) and 0.455 ± 0.06 (P value 0.0004), respectively. Elevated levels of fragments and chromatid aberrations are suggestive of low-dose radiation effects and also chemically-induced DNA damage. (authors)

Worker Entrepreneurship.

Science.gov (United States)

Doucouliagos, Chris

1992-01-01

Evaluates the experience of worker entrepreneurship, highlighting successes and failures in Europe, and analyzes the relative importance of factors to worker entrepreneurship such as access to finance, education and training, organizational culture, and worker risk taking. (JOW)

A prospective study of Romanian agriculture workers for zoonotic influenza infections.

Directory of Open Access Journals (Sweden)

Alexandru Coman

Full Text Available In this prospective study we sought to examine seroepidemiological evidence for acute zoonotic influenza virus infection among Romanian agricultural workers.Sera were drawn upon enrollment (2009 and again at 12 and 24 months from 312 adult agriculture workers and 51 age-group matched controls. Participants were contacted monthly for 24 months and queried regarding episodes of acute influenza-like illnesses (ILI. Cohort members meeting ILI criteria permitted respiratory swab collections as well as acute and convalescent serum collection. Serologic assays were performed against 9 avian, 3 swine, and 3 human influenza viruses.During the two-year follow-up, a total of 23 ILI events were reported. Two subjects' specimens were identified as influenza A by rRT-PCR. During the follow-up period, three individuals experienced elevated microneutralization antibody titers ≥1∶80 against three (one each avian influenza viruses: A/Teal/Hong Kong/w312/97(H6N1, A/Hong Kong/1073/1999(H9N2, or A/Duck/Alberta/60/1976(H12N5. However, none of these participants met the criteria for poultry exposure. A number of subjects demonstrated four-fold increases over time in hemagglutination inhibition (HI assay titers for at least one of the three swine influenza viruses (SIVs; however, it seems likely that two of these three responses were due to cross-reacting antibody against human influenza. Only elevated antibody titers against A/Swine/Flanders/1/1998(H3N2 lacked evidence for such confounding. In examining risk factors for elevated antibody against this SIV with multiple logistic regression, swine exposure (adjusted OR = 1.8, 95% CI 1.1-2.8 and tobacco use (adjusted OR = 1.8; 95% CI 1.1-2.9 were important predictors.While Romania has recently experienced multiple incursions of highly pathogenic avian influenza among domestic poultry, this cohort of Romanian agriculture workers had sparse evidence of avian influenza virus infections. In contrast, there was

Origins of amorphous interstellar grains

International Nuclear Information System (INIS)

Hasegawa, H.

1984-01-01

The existence of amorphous interstellar grains has been suggested from infrared observations. Some carbon stars show the far infrared emission with a lambda -1 wavelength dependence. Far infrared emission supposed to be due to silicate grains often show the lambda -1 wavelength dependence. Mid infrared spectra around 10 μm have broad structure. These may be due to the amorphous silicate grains. The condition that the condensed grains from the cosmic gas are amorphous is discussed. (author)

Catalysts of worker-to-worker violence and incivility in hospitals.

Science.gov (United States)

Hamblin, Lydia E; Essenmacher, Lynnette; Upfal, Mark J; Russell, Jim; Luborsky, Mark; Ager, Joel; Arnetz, Judith E

2015-09-01

To identify common catalysts of worker-to-worker violence and incivility in hospital settings. Worker-to-worker violence and incivility are prevalent forms of mistreatment in healthcare workplaces. These are forms of counterproductive work behaviour that can lead to negative outcomes for employees, patients and the organisation overall. Identifying the factors that lead to co-worker mistreatment is a critical first step in the development of interventions targeting these behaviours. Retrospective descriptive study. Qualitative content analysis was conducted on the total sample (n = 141) of employee incident reports of worker-to-worker violence and incivility that were documented in 2011 at a large American hospital system. More than 50% of the incidents involved nurses, and the majority of incidents did not involve physical violence. Two primary themes emerged from the analysis: Work Behaviour and Work Organisation. Incidents in the Work Behaviour category were often sparked by unprofessional behaviour, disagreement over responsibilities for work tasks or methods of patient care, and dissatisfaction with a co-worker's performance. Incidents in the Work Organisation category involved conflicts or aggression arising from failure to following protocol, patient assignments, limited resources and high workload. Incidents of worker-to-worker violence and incivility stemmed from dissatisfaction with employee behaviour or from organisational practices or work constraints. These incident descriptions reflect worker dissatisfaction and frustration, resulting from poor communication and collaboration between employees, all of which threaten work productivity. Violence and incivility between hospital employees can contribute to turnover of top performers, hinder effective teamwork and jeopardise the quality of patient care. Identification of common catalysts for worker-to-worker violence and incivility informs the development of mistreatment prevention programmes that can be

Tracer concentration contours in grain lattice and grain boundary diffusion

International Nuclear Information System (INIS)

Kim, Y. S.; Olander, D. R.

1997-01-01

Grain boundary diffusion plays a significant role in fission gas release, which is one of the crucial processes dominating nuclear fuel performance. Gaseous fission products such as Xe and Kr generated during nuclear fission have to diffuse in the grain lattice and the boundary inside fuel pellets before they reach the open spaces in a fuel rod. These processes can be studied by 'tracer diffusion' techniques, by which grain boundary diffusivity can be estimated and directly used for low burn-up fission gas release analysis. However, only a few models accounting for the both processes are available and mostly handle them numerically due to mathematical complexity. Also the numerical solution has limitations in a practical use. In this paper, an approximate analytical solution in case of stationary grain boundary in a polycrystalline solid is developed for the tracer diffusion techniques. This closed-form solution is compared to available exact and numerical solutions and it turns out that it makes computation not only greatly easier but also more accurate than previous models. It can be applied to theoretical modelings for low burn-up fission gas release phenomena and experimental analyses as well, especially for PIE (post irradiation examination). (author)

Snow crab allergy and asthma among Greenlandic workers – a pilot study

Directory of Open Access Journals (Sweden)

Jakob Hjort Bønløkke

2012-08-01

Full Text Available Objectives. To study snow crab sensitization, occupational allergy and asthma in the snow crab industry in Greenland, as high rates have been found in Canada, but no reports have emerged from the same industry in Greenland. Study design. Pilot survey. Methods. Twenty workers (19 of Inuit and 1 of other origin in a snow crab (Chionoecetes opilio and Atlantic shrimp (Pandalus borealis processing plant in Greenland were assessed with skin prick tests (SPTs with common aeroallergens and specific allergens from snow crab and shrimp extracts, spirometry, blood sampling for total IgE and specific IgE determination. Eighteen workers contributed a questionnaire-based medical interview. Results. Positive skin prick test reactions were common to snow crab (40% and shrimp (20%. Specific IgE to snow crab were positive in 4 workers (21%. Two workers had elevated total IgE levels. Symptoms suggestive of asthma were common (45%. Work-related symptoms of skin rash, rhinitis, and/or conjunctivitis were reported by 50%, and symptoms from the lower airways by 39%. Combining history of work-related symptoms with results from specific SPTs and/or specific IgE determination suggested that 11 and 22% of workers suffered from probable and possible occupational asthma, respectively, whereas 22% had possible occupational dermatitis or rhinitis. Conclusions. Greenlander Inuit do not appear to be protected against sensitization to snow crab or shrimp when occupationally exposed to these. This pilot study suggests that occupational allergy and asthma may be as common a problem in Greenlandic workers as in Canadian.

Ferroelectric domain continuity over grain boundaries

DEFF Research Database (Denmark)

Mantri, Sukriti; Oddershede, Jette; Damjanovic, Dragan

2017-01-01

Formation and mobility of domain walls in ferroelectric materials is responsible for many of their electrical and mechanical properties. Domain wall continuity across grain boundaries has been observed since the 1950's and is speculated to affect the grain boundary-domain interactions, thereby...... impacting macroscopic ferroelectric properties in polycrystalline systems. However detailed studies of such correlated domain structures across grain boundaries are limited. In this work, we have developed the mathematical requirements for domain wall plane matching at grain boundaries of any given...... orientation. We have also incorporated the effect of grain boundary ferroelectric polarization charge created when any two domains meet at the grain boundary plane. The probability of domain wall continuity for three specific grain misorientations is studied. Use of this knowledge to optimize processing...

Pentoxifylline does not alter the response to inhaled grain dust.

Science.gov (United States)

Jagielo, P J; Watt, J L; Quinn, T J; Knapp, H R; Schwartz, D A

1997-05-01

Pentoxifylline (PTX) has been shown to reduce sepsis-induced neutrophil sequestration in the lung and inhibit endotoxin-mediated release of tumor necrosis factor-alpha (TNF-alpha). Previously, we have shown that endotoxin appears to be the principal agent in grain dust causing airway inflammation and airflow obstruction following grain dust inhalation. To determine whether PTX affects the physiologic and inflammatory events following acute grain dust inhalation, 10 healthy, nonsmoking subjects with normal airway reactivity were treated with PTX or placebo (PL) followed by corn dust extract (CDE) inhalation (0.08 mL/kg), using a single-blinded, crossover design. Subjects received PTX (1,200 mg/d) or PL for 4 days prior to CDE inhalation and 400 mg PTX or PL on the exposure day. Both respiratory symptoms and declines in FEV1 and FVC occurred following CDE exposure in both groups, but there were no significant differences in the frequency of symptoms or percent declines from baseline in the FEV1 and FVC at any of the time points measured in the study. Elevations in peripheral blood leukocyte and neutrophil concentrations and BAL total cell, neutrophil, TNF-alpha, and interleukin-8 concentrations were measured 4 h following exposure to CDE in both the PTX- and PL-treated subjects, but no significant differences were found between treatment groups. These results suggest that pretreatment with PTX prior to inhalation of CDE, in the doses used in this study, does not alter the acute physiologic or inflammatory events following exposure to inhaled CDE.

Branching-induced grain boundary evolution during directional solidification of columnar dendritic grains

International Nuclear Information System (INIS)

Guo, Chunwen; Li, Junjie; Yu, Honglei; Wang, Zhijun; Lin, Xin; Wang, Jincheng

2017-01-01

We present an investigation of secondary and tertiary branching behavior in diverging grain boundaries (GBs) between two columnar dendritic grains with different crystallographic orientations, both by two-dimensional phase-field simulations and thin-sample experiments. The stochasticity of the GB trajectories and the statistically averaged GB orientations were analyzed in detail. The side-branching dynamics and subsequent branch competition behaviors found in the simulations agreed well with the experimental results. When the orientations of two grains are given, the experimental results indicated that the average GB orientation was independent of the pulling velocity in the dendritic growth regime. The simulation and experimental results, as well as the results reported in the literature exhibit a uniform relation between the percentage of the whole gap region occupied by the favorably oriented grain and the difference in the absolute values of the secondary arm growth directions of the two competitive grains. By describing such a uniform relation with a simple fitting equation, we proposed a simple analytical model for the GB orientation at diverging GBs, which gives a more accurate description of GB orientation selection than the existing models.

The effect of grain refinement and silicon content on grain formation in hypoeutectic Al-Si alloys

Energy Technology Data Exchange (ETDEWEB)

Lee, Y.C.; Dahle, A.K.; StJohn, D.H.; Hutt, J.E.C. [Queensland Univ., Brisbane (Australia). Dept. of Mining, Minerals and Mater. Eng.

1999-01-15

The effect of increasing the amount of added grain refiner on grain size and morphology has been investigated for a range of hypoeutectic Al-Si alloys. The results show a transition in grain size at a silicon concentration of about 3 wt% in unrefined alloys; the grain size decreasing with silicon content before the transition, and increasing beyond the transition point. A change in morphology also occurs with increased silicon content. The addition of grain refiner leads to greater refinement for silicon contents below the transition point than for those contents above the transition point, while the transition point seems to remain unchanged. The slope of the grain size versus silicon content curve after the transition seems to be unaffected by the degree of grain refinement. The results are related to the competitive processes of nucleation and constitutional effects during growth and their impact on nucleation kinetics. (orig.) 13 refs.

Compaction of cereal grain

OpenAIRE

Wychowaniec, J.; Griffiths, I.; Gay, A.; Mughal, A.

2013-01-01

We report on simple shaking experiments to measure the compaction of a column of Firth oat grain. Such grains are elongated anisotropic particles with a bimodal polydispersity. In these experiments, the particle configurations start from an initially disordered, low-packing-fraction state and under vertical shaking evolve to a dense state with evidence of nematic-like structure at the surface of the confining tube. This is accompanied by an increase in the packing fraction of the grain.

A novel wheat variety with elevated content of amylose increases resistant starch formation and may beneficially influence glycaemia in healthy subjects

Directory of Open Access Journals (Sweden)

Elin Östman

2011-08-01

Full Text Available Previous studies indicate that elevated amylose content in products from rice, corn, and barley induce lower postprandial glycaemic responses and higher levels of resistant starch (RS. Consumption of slowly digestible carbohydrates and RS has been associated with health benefits such as decreased risk of diabetes and cardiovascular disease.To evaluate the postprandial glucose and insulin responses in vivo to bread products based on a novel wheat genotype with elevated amylose content (38%.Bread was baked from a unique wheat genotype with elevated amylose content, using baking conditions known to promote amylose retrogradation. Included test products were bread based on whole grain wheat with elevated amylose content (EAW, EAW with added lactic acid (EAW-la, and ordinary whole grain wheat bread (WGW. All test breads were baked at pumpernickel conditions (20 hours, 120°C. A conventionally baked white wheat bread (REF was used as reference. Resistant starch (RS content was measured in vitro and postprandial glucose and insulin responses were tested in 14 healthy subjects.The results showed a significantly higher RS content (on total starch basis in breads based on EAW than in WGW (p<0.001. Lactic acid further increased RS (p<0.001 compared with both WGW and EAW. Breads baked with EAW induced lower postprandial glucose response than REF during the first 120 min (p<0.05, but there were no significant differences in insulin responses. Increased RS content per test portion was correlated to a reduced glycaemic index (GI (r= − 0.571, p<0.001.This study indicates that wheat with elevated amylose content may be preferable to other wheat genotypes considering RS formation. Further research is needed to test the hypothesis that bread with elevated amylose content can improve postprandial glycaemic response.

Molecular dynamics study on microstructure of near grain boundary distortion region in small grain size nano- NiAl alloy

International Nuclear Information System (INIS)

Wang, J.Y.; Wang, X.W.; Rifkin, J.; Li, D.X.

2001-12-01

Using the molecular dynamics simulation method, the microstructure of distortion region near curved amorphous-like grain boundary in nano-NiAl alloy is studied. The results showed that due to the internal elastic force of high energy grain boundary, distortion layer exists between grain and grain boundary. The lattice expansion and structure factor decreasing are observed in this region. Stacking fault in sample with grain size 3.8nm is clearly observed across the distortion region at the site very close to grain. The influences of different grain sizes on average distortion degree and volume fractions of distortion region, grain and grain boundary are also discussed. (author)

Microstructure and mechanical properties of sputter deposited Ni/Ni{sub 3}Al multilayer films at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Zhang, Chao [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China); Feng, Kai, E-mail: fengkai@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China); Li, Zhuguo, E-mail: lizg@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China); Lu, Fenggui; Huang, Jian; Wu, Yixiong [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China)

2016-08-15

Highlights: • Ni/Ni{sub 3}Al multilayers are prepared by magnetron sputtering. • Both grain size and phase constitution of annealed Ni/Ni{sub 3}Al multilayers are dependent on individual layer thickness. • The hardness of annealed Ni/Ni{sub 3}Al multilayers varies with individual layer thickness and annealing temperature. • 40 nm Ni/Ni{sub 3}Al multilayer exhibits excellent hardness at elevated temperature. - Abstract: Nano-structured Ni/Ni{sub 3}Al multilayer was prepared by magnetron sputtering, with individual layer thicknesses h varying from 10 to 160 nm. The microstructure and hardness of Ni/Ni{sub 3}Al multilayer were investigated by X-ray diffraction, transmission electron microscopy and nanoindentation. The results show that the hardness increases with decreasing h for as-deposited and 500 °C annealed multilayers. When annealed at 700 °C, the hardness approach a peak value at h = 40 nm with followed by softening at smaller h. The influence of individual layer thickness, grain size as well as formation of ordered Ni{sub 3}Al on strengthening mechanisms of Ni/Ni{sub 3}Al multilayers at elevated temperature are discussed.

7 CFR 868.310 - Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice...

Science.gov (United States)

2010-01-01

... Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice. (See also Â... Milled Rice Principles Governing Application of Standards § 868.310 Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice...

Heart Rate, Stress, and Occupational Noise Exposure among Electronic Waste Recycling Workers.

Science.gov (United States)

Burns, Katrina N; Sun, Kan; Fobil, Julius N; Neitzel, Richard L

2016-01-19

Electronic waste (e-waste) is a growing occupational and environmental health issue around the globe. E-waste recycling is a green industry of emerging importance, especially in low-and middle-income countries where much of this recycling work is performed, and where many people's livelihoods depend on this work. The occupational health hazards of e-waste recycling have not been adequately explored. We performed a cross-sectional study of noise exposures, heart rate, and perceived stress among e-waste recycling workers at a large e-waste site in Accra, Ghana. We interviewed 57 workers and continuously monitored their individual noise exposures and heart rates for up to 24 h. More than 40% of workers had noise exposures that exceeded recommended occupational (85 dBA) and community (70 dBA) noise exposure limits, and self-reported hearing difficulties were common. Workers also had moderate to high levels of perceived stress as measured via Cohen's Perceived Stress Scale, and reported a variety of symptoms that could indicate cardiovascular disease. Noise exposures were moderately and significantly correlated with heart rate (Spearman's ρ 0.46, p stress, and unfavorable physical working conditions. These findings suggest that occupational and non-occupational noise exposure is associated with elevations in average heart rate, which may in turn predict potential cardiovascular damage.

Multiple myeloma, leukemia, and breast cancer among the US radium dial workers

International Nuclear Information System (INIS)

Stebbings, J.H.; Lucas, H.F.; Stehney, A.F.

1983-01-01

The relationships of radium exposure to mortality from multiple myeloma, leukemia, and breast cancer were studied in three cohorts of female dial workers defined by year of first employment. Mortality was compared with that expected from US white female rates, with and without adjustment for local mortality rates. Dose-response relationships of these cancers to systemic intake of radium were determined in workers whose body burdens had been measured in vivo since 1955. Incident cases of multiple myeloma occurred in the pre-1930 cohort; however, analyses of body burdens and durations of employment suggest that external radiation was more likely to have been responsible than was internal radium. Leukemia incidence and mortality have not been elevated overall among the female dial workers, either in the pre-1930 or the post-1930 cohorts, but cases have tended to occur early and in subjects with higher body burdens. Extensive analyses of breast cancer data have uncovered several observations weighing against a causal interpretation of the association between radium and breast cancer

B2 Grain Growth Behavior of a Ti-22Al-25Nb Alloy Fabricated by Hot Pressing Sintering

Science.gov (United States)

Jia, Jianbo; Liu, Wenchao; Xu, Yan; Chen, Chen; Yang, Yue; Luo, Junting; Zhang, Kaifeng

2018-05-01

Grain growth behavior of a powder metallurgy (P/M) Ti-22Al-25Nb alloy was investigated by applying a series of isothermal treatment tests over a wide range of temperatures and holding times. An isothermal treatment scheme was conducted in the B2 phase region (1070-1110 °C) and α 2 + B2 phase region (1010-1050 °C) at holding times of 10, 30 min, 1, 2, and 3 h, respectively. The effects of temperature and holding time on the microstructure evolution and microhardness of the P/M Ti-22Al-25Nb alloy at elevated temperatures were evaluated using optical microscope, scanning electron microscope, x-ray diffraction, and Vickers hardness test techniques. The results revealed that the alloy's treated microstructure was closely linked to temperature and holding time, respectively. The change law of B2 grain growth with holding time and temperature can be well interpreted by the Beck equation and Hillert equation, respectively. The B2 grain growth exponent n and activation energy Q were acquired based on experimental data in the α 2 + B2 and B2 phase regions. In addition, the grain growth contour map for the P/M Ti-22Al-25Nb alloy was constructed to depict variations in B2 grain size based on holding time and temperature.

Pressure effect on grain boundary diffusion

International Nuclear Information System (INIS)

Smirnova, E.S.; Chuvil'deev, V.N.

1997-01-01

The influence of hydrostatic pressure on grain boundary diffusion and grain boundary migration in metallic materials is theoretically investigated. The model is suggested that permits describing changes in activation energy of grain boundary self-diffusion and diffusion permeability of grain boundaries under hydrostatic pressure. The model is based on the ideas about island-type structure of grain boundaries as well as linear relationship of variations in grain boundary free volume to hydrostatic pressure value. Comparison of theoretical data with experimental ones for a number of metals and alloys (α-Zr, Sn-Ge, Cu-In with Co, In, Al as diffusing elements) shows a qualitative agreement

Ochratoxin A in grain dust--estimated exposure and relations to agricultural practices in grain production.

Science.gov (United States)

Halstensen, Anne Straumfors; Nordby, Karl-Christian; Elen, Oleif; Eduard, Wijnand

2004-01-01

Ochratoxin A (OTA) is a nephrotoxin frequently contaminating grains. OTA inhalation during grain handling may therefore represent a health risk to farmers, and was the subject of this study. Airborne and settled grain dust was collected during grain work on 84 Norwegian farms. Climate and agricultural practices on each farm were registered. Penicillium spp., Aspergillus spp. and OTA in settled dust were measured. Settled dust contained median 4 microg OTA/kg dust (range 2-128), correlating with Penicillium spp. (median 40 cfu/mg; range 0-32000, rs =0.33; p grain species, districts and agricultural practices. Penicillium levels, but not OTA levels, were higher in storage than in threshing dust (p=0.003), and increased with storage time (rs =0.51, p dust during threshing and median 7 mg/m3 (range 1-110) dust during storage work, equalling median 3.7 pg/m3 (range 0.6-200) and median 40 pg/m3 (range 2-14000) OTA, respectively (p grain work was low, although varying by more than 1,000-fold. However, the farmers may occasionally be highly exposed, particularly during handling of stored grain.

Evolution of orientations and deformation structures within individual grains in cold rolled columnar grained nickel

DEFF Research Database (Denmark)

Wu, G.L.; Godfrey, A.; Winther, Grethe

2011-01-01

Columnar grained Ni is used as a model material allowing simultaneous non-surface investigations of the evolution of crystallographic orientations and deformation microstructures within individual grains as a function of rolling strain up to ε=0.7. Electron channelling contrast and electron...... backscattered diffraction are used to visualise microstructures and crystallographic orientations. It is found that both the microstructural and the textural development depend strongly on the initial grain orientation. A grain size effect is observed on the deformation-induced orientation scatter within...

Multiple myeloma, leukemia, and breast cancer among the US radium dial workers

International Nuclear Information System (INIS)

Stebbings, J.H.; Lucas, H.F.; Stehney, A.F.

1984-01-01

The relationships of radium exposure to mortality from multiple myeloma, leukemia, and breast cancer were studied in three cohorts of female dial workers defined by year of first employment. A three-fold excess risk of multiple myeloma occurred in the pre-1930 cohort; however, analyses of body burdens and durations of employment suggest that external radiation was more likely to have been responsible than was internal radium. Leukemia incidence and mortality have not been elevated overall among the female dial workers, either in the pre-1930 or the post-1930 cohorts, but cases have tended to occur early and in subjects with higher body burdens of radium. Extensive analyses of breast cancer data have uncovered several observations weighing against a causal interpretation of the association between radium body burdens and breast cancer

Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone

International Nuclear Information System (INIS)

Wan, X.L.; Wei, R.; Wu, K.M.

2010-01-01

The microstructure of acicular ferrite and its formation for the grain refinement of coarse-grained region of heat-affected zone of high strength low-alloy bainite steels were studied using three-dimensional reconstruction technique. Crystallographic grain size was analyzed by means of electron backscatter diffraction. It was revealed that the microstructure in the coarse-grained region of the heat-affected zone consisted of predominantly bainite packets and a small proportion of acicular ferrite. Acicular ferrite was of lath or plate-like rather than needle or rod-like morphology. Tempering of the coarse-grained region of heat-affected zone showed that the acicular ferrite was more stable than the bainite, indicating that the acicular ferrite was formed prior to bainite. The acicular ferrite laths or plates divided the prior austenite grains into smaller and separate regions, and confining the bainite transformed at lower temperatures in the smaller regions and hence leading to the grain refinement in the coarse-grained region of the heat-affected zone.

Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone

Energy Technology Data Exchange (ETDEWEB)

Wan, X.L.; Wei, R. [Institute of Advanced Steels and Welding Technology, Hubei Provincial Key Laboratory for Systems Science on Metallurgical Processing, Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081 (China); Wu, K.M., E-mail: wukaiming@wust.edu.cn [Institute of Advanced Steels and Welding Technology, Hubei Provincial Key Laboratory for Systems Science on Metallurgical Processing, Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081 (China)

2010-07-15

The microstructure of acicular ferrite and its formation for the grain refinement of coarse-grained region of heat-affected zone of high strength low-alloy bainite steels were studied using three-dimensional reconstruction technique. Crystallographic grain size was analyzed by means of electron backscatter diffraction. It was revealed that the microstructure in the coarse-grained region of the heat-affected zone consisted of predominantly bainite packets and a small proportion of acicular ferrite. Acicular ferrite was of lath or plate-like rather than needle or rod-like morphology. Tempering of the coarse-grained region of heat-affected zone showed that the acicular ferrite was more stable than the bainite, indicating that the acicular ferrite was formed prior to bainite. The acicular ferrite laths or plates divided the prior austenite grains into smaller and separate regions, and confining the bainite transformed at lower temperatures in the smaller regions and hence leading to the grain refinement in the coarse-grained region of the heat-affected zone.

Evolution of interstellar grains

International Nuclear Information System (INIS)

Greenberg, J.M.

1984-01-01

The principal aim of this chapter is to derive the properties of interstellar grains as a probe of local physical conditions and as a basis for predicting such properties as related to infrared emissivity and radiative transfer which can affect the evolution of dense clouds. The first sections will develop the criteria for grain models based directly on observations of gas and dust. A summary of the chemical evolution of grains and gas in diffuse and dense clouds follows. (author)

Preliminary studies on fluid inclusions in metasomatic albite grains from Lagoa Real, Caetite, Ba, Brazil

International Nuclear Information System (INIS)

Fuzikawa, K.

1980-01-01

Preliminary fluid inclusion studies in metasomatic albite grains from the Lagoa Real uranium deposit pointed out to mixing of strong brines (23 wt% NaCl equivalent) with low salinity fluids (2.3 wt% NaCl equivalent). Microthermometry and crushing tests indicated elevated pressures and the presence of hidrocarbons in larger amount than CO 2 . The remobilization of uranium as uranyl carbonate complexes and its precipitation, reducing U 6 + to U 4 + by CH 4 , is considered as a possibility. (Author) [pt

Silicosis and lung function decrements among female ceramic workers in Italy.

Science.gov (United States)

Forastiere, Francesco; Goldsmith, David F; Sperati, Alessandra; Rapiti, Elisabetta; Miceli, Maria; Cavariani, Fulvio; Perucci, Carlo A

2002-11-01

It is well known that male ceramic workers have elevated risks of chronic silicosis. The objective of this study was to assess whether female ceramic workers also have an increased risk of silicosis and whether these women have decreased lung function related to silica exposure. Ceramic workers from Civitacastellana, Italy, were enrolled in health surveillance during the 1970s. A total of 642 women were under surveillance; a respiratory monitoring program was conducted from 1974 to 1987, with follow-up through 1991 that included annual chest radiography and measurement of lung function. Radiography findings were defined as silicosis if the chest films were > or =1/0 with small, rounded opacities. Multiple linear regression models for repeated measures (generalized estimating equations) were run to evaluate associations of forced vital capacity (FVC) and forced expiratory volume in 1 second (FEV(1)) with years of exposure and radiograph opacities. Nine cases of silicosis were identified on the basis of radiographic evidence. Silicosis risk was not associated with smoking but was related to employment before 1970 and demonstrated a dose-response gradient for years of exposure. FVC and FEV(1) both showed significant (p associations with duration of exposure and with positive radiography findings. The results for female ceramic workers are consistent with those for male employees regarding exposure to fibrogenic dusts.

A constitutive model of nanocrystalline metals based on competing grain boundary and grain interior deformation mechanisms

KAUST Repository

Gurses, Ercan; El Sayed, Tamer S.

2011-01-01

In this work, a viscoplastic constitutive model for nanocrystalline metals is presented. The model is based on competing grain boundary and grain interior deformation mechanisms. In particular, inelastic deformations caused by grain boundary

Grain Formation Processes in Oxygen-Rich Circumstellar Outflows: Testing the Metastable Eutectic Condensation Hypothesis and Measuring Atom-Grain & Grain-Grain Sticking Coefficients (A Sub-orbital Investigation)

Science.gov (United States)

Nuth, Joseph

An experimentally-based model of grain formation in oxygen-rich circumstellar outflows that includes vapor-solid nucleation, grain growth, thermal annealing and grain aggregation in sufficient detail to predict the spectral energy distribution (SED) of the shells for comparison with observations of a wide range of stellar sources still lacks critical data. In order to gather this data we propose to conduct a series of laboratory experiments using our proven experimental system and microgravity condensation, growth and grain aggregation experiments on sounding rockets with a flight-proven payload provided by Dr. Yuki Kimura of Hokkaido University. We have proposed that solids from a hydrogen-rich, supersaturated, Fe-Mg-SiO vapor condense at metastable eutectic points in this ternary phase diagram. Because the FeOMgO system is totally miscible (has no eutectic or metastable eutectic compositions), this predicts that condensates will be pure Mg-silicate or Fe-silicate grains and that no primary condensate will be a mixed Fe-Mg-silicate. We have shown that this observation leads to a logical explanation as to why pure magnesium olivine and enstatite minerals are detected in circumstellar winds rather than the mixed Mg-Fe-silicate grains that might otherwise be expected (Rietmeijer, Nuth & Karner, 1999). This simplifying hypothesis has been built into our models of circumstellar condensation and growth. However, these experimental results require confirmation and testing since they should apply to other, quite similar condensable systems. We propose to test this hypothesis by condensing solids from the Fe-Mg-AlO ternary vapor system. Since FeO-MgO miscibility also applies to this system, the primary condensates from such a vapor should consist of pure amorphous Fe-aluminates and Mg-aluminates. No mixed Fe-Mg-spinels should be detected as primary condensates if this hypothesis is correct, just as none were detected for the FeO-MgO-SiO system. Confirmation of this

Storing Peanuts in Grain Bags

Science.gov (United States)

A study was executed to determine the potential of storing farmers stock peanuts and shelled peanuts for crushing in hermetically sealed grain bags. The objectives of the study were to evaluate equipment for loading and unloading the grain bags, the capacity of the grain bags, and the changes in qu...

Plant Density Effect on Grain Number and Weight of Two Winter Wheat Cultivars at Different Spikelet and Grain Positions

OpenAIRE

Li, Yong; Cui, Zhengyong; Ni, Yingli; Zheng, Mengjing; Yang, Dongqing; Jin, Min; Chen, Jin; Wang, Zhenlin; Yin, Yanping

2016-01-01

In winter wheat, grain development is asynchronous. The grain number and grain weight vary significantly at different spikelet and grain positions among wheat cultivars grown at different plant densities. In this study, two winter wheat (Triticum aestivum L.) cultivars, 'Wennong6' and 'Jimai20', were grown under four different plant densities for two seasons, in order to study the effect of plant density on the grain number and grain weight at different spikelet and grain positions. The resul...

Segregation of solute elements at grain boundaries in an ultrafine grained Al-Zn-Mg-Cu alloy

International Nuclear Information System (INIS)

Sha, Gang; Yao, Lan; Liao, Xiaozhou; Ringer, Simon P.; Chao Duan, Zhi; Langdon, Terence G.

2011-01-01

The solute segregation at grain boundaries (GBs) of an ultrafine grained (UFG) Al-Zn-Mg-Cu alloy processed by equal-channel angular pressing (ECAP) at 200 o C was characterised using three-dimensional atom probe. Mg and Cu segregate strongly to the grain boundaries. In contrast, Zn does not always show clear segregation and may even show depletion near the grain boundaries. Trace element Si selectively segregates at some GBs. An increase in the number of ECAP passes leads to a decrease in the grain size but an increase in solute segregation at the boundaries. The significant segregation of alloying elements at the boundaries of ultrafine-grained alloys implies that less solutes will be available in the matrix for precipitation with a decrease in the average grain size. -- Research Highlights: → Atom probe tomography has been employed successfully to reveal unique segregation of solutes at ultrafine grained material. → Mg and Cu elements segregated strongly at the grain boundary of an ultrafine grained Al-Zn-Mg-Cu alloy processed by 4-pass and 8-pass ECAP at 200 o C. Zn frequently depleted at GBs with a Zn depletion region of 7-15 nm in width on one or both sides of the GBs. Only a small fraction (3/13) of GBs were observed with a low level of Zn segregation where the combined Mg and Cu excess is over 3.1 atom/nm 2 . Si appeared selectively segregated at some of the GBs. → The increase in number of ECAP passes from 4 to 8 correlated with the increase in mean level segregation of Mg and Cu for both solute excess and peak concentration. → The change of plane normal of a grain boundary within 30 o only leads to a slight change in the solute segregation level.

Grain growth studies on nanocrystalline Ni powder

International Nuclear Information System (INIS)

Rane, G.K.; Welzel, U.; Mittemeijer, E.J.

2012-01-01

The microstructure of nanocrystalline Ni powder produced by ball-milling and its thermal stability were investigated by applying different methods of X-ray diffraction line-profile analysis: single-line analysis, whole powder-pattern modelling and the (modified) Warren–Averbach method were employed. The kinetics of grain growth were investigated by both ex-situ and in-situ X-ray diffraction measurements. With increasing milling time, the grain-size reduction is accompanied by a considerable narrowing of the size distribution and an increase in the microstrain. Upon annealing, initial, rapid grain growth occurs, accompanied by the (almost complete) annihilation of microstrain. For longer annealing times, the grain-growth kinetics depend on the initial microstructure: a smaller microstrain with a broad grain-size distribution leads to linear grain growth, followed by parabolic grain growth, whereas a larger microstrain with a narrow grain-size distribution leads to incessant linear grain growth. These effects have been shown to be incompatible with grain-boundary curvature driven growth. The observed kinetics are ascribed to the role of excess free volume at the grain boundaries of nanocrystalline material and the prevalence of an “abnormal grain-growth” mechanism.

The metabolism of carbohydrates and lipid peroxidation in lead-exposed workers.

Science.gov (United States)

Kasperczyk, Aleksandra; Dobrakowski, Michal; Ostałowska, Alina; Zalejska-Fiolka, Jolanta; Birkner, Ewa

2015-12-01

The present study was undertaken to estimate the effect of occupational exposure to lead on the blood concentration of glucose and several enzymes involved in glycolysis, the citric acid cycle, and the pentose phosphate pathway. To estimate the degree of lipid peroxidation, the concentrations of conjugated dienes were determined. The examined group included 145 healthy male employees of lead-zinc works. Taking into account the mean blood lead levels, the examined group was divided into two subgroups. The control group was composed of 36 healthy male administrative workers. The markers of lead exposure were significantly elevated in both subgroups when compared with the controls. There were no significant changes in fasting glucose concentration and fructose-1,6-bisphosphate aldolase activity in the study population. The concentration of conjugated dienes was significantly higher in both subgroups, whereas the activity of malate dehydrogenase was significantly higher only in the group with higher exposure. The activities of lactate dehydrogenase and sorbitol dehydrogenase were significantly decreased in the examined subgroups. The activity of glucose-6-phosphate dehydrogenase decreased significantly in the group with higher exposure and could be the cause of the elevated concentrations of conjugated dienes. It is possible to conclude that lead interferes with carbohydrate metabolism, but compensatory mechanisms seem to be efficient, as glucose homeostasis in lead-exposed workers was not disturbed. © The Author(s) 2013.

Fatal injuries among grounds maintenance workers: United States, 2003--2008.

Science.gov (United States)

2011-05-06

A total of 1,142 grounds maintenance workers (GMWs) were fatally injured at work during 2003--2008, an average of 190 each year. GMWs accounted for 3.4% of all occupational fatalities, and 31% of those GMWs were Hispanic or Latino. Approximately 83% of the Hispanic or Latino GMWs who died were born outside the United States. In 2008, approximately 1.52 million persons were employed as GMWs, constituting 1.0% of the U.S. workforce. During 2003--2007, an average of 13.3 per 100,000 employed GMWs died each year, compared with an overall rate of 4.0 fatalities per 100,000 U.S. workers. The rate of on-the-job fatal injuries among GMWs has remained elevated relative to other workers for >20 years. This report characterizes events leading to GMW fatalities and differences in fatality characteristics across demographic groups among GMWs, based on an evaluation of 2003--2008 data from the U.S. Department of Labor's Bureau of Labor Statistics (BLS) Census of Fatal Occupational Injuries (CFOI) program. The report also identifies workplace interventions that might reduce the incidence of fatal injuries. Major events leading to GMW occupational fatalities included transportation incidents (31%), contact with objects and equipment (25%), falls (23%), and traumatic acute exposures to harmful substances or environments (e.g., electrocution and drowning) (16%). To reduce the incidence of such fatalities, employers, trade and worker associations, and policy makers should focus on effective, targeted workplace safety interventions such as frequent hazard identification and training for specific hazards. Diversity among the populations of workers requires use of culture- and language-appropriate training techniques as part of comprehensive injury and illness prevention programs.

Grain-to-grain variations in NbC particle size distributions in an austenitic stainless steel

International Nuclear Information System (INIS)

Barlow, C.Y.; Ralph, B.; Silverman, B.; Jones, A.R.

1979-01-01

Quantitative information has been obtained concerning the size distributions of NbC precipitate particles in different grains in a deformed and aged austenitic stainless steel specimen. The precipitate size distributions obtained differ from one grain to another. The average disparity measured between the mean precipitate sizes was a function of the distance between the grains compared. The results obtained are considered in terms of differences in precipitation behaviour due to variations in the levels of plastic strain in constituent grains of the deformed specimen. (author)

Grain refinement of zinc-aluminium alloys

International Nuclear Information System (INIS)

Zaid, A.I.O.

2006-01-01

It is now well-established that the structure of the zinc-aluminum die casting alloys can be modified by the binary Al-Ti or the ternary Al-Ti-B master alloys. in this paper, grain refinement of zinc-aluminum alloys by rare earth materials is reviewed and discussed. The importance of grain refining of these alloys and parameters affecting it are presented and discussed. These include parameters related to the Zn-Al alloys cast, parameters related to the grain refining elements or alloys and parameters related to the process. The effect of addition of other alloying elements e.g. Zr either alone or in the presence of the main grain refiners Ti or Ti + B on the grain refining efficiency is also reviewed and discussed. Furthermore, based on the grain refinement and the parameters affecting it, a criterion for selection of the optimum grain refiner is suggested. Finally, the recent research work on the effect of grain refiners on the mechanical behaviour, impact strength, wear resistance, and fatigue life of these alloys are presented and discussed. (author)

Effect of sintering condition on the grain growth of Cr{sub 2}O{sub 3} doped UO{sub 2} pellets

Energy Technology Data Exchange (ETDEWEB)

Oh, Jang Soo; Kim, Keon Sik; Kim, Dong Joo; Kim, Jong Hun; Yang, Jae Ho [KAERI, Daejeon (Korea, Republic of)

2016-05-15

In this paper, Cr{sub 2}O{sub 3} doped UO{sub 2} pellets were fabricated by two-step sintering process. The grain growth of pellet is related to dwell time in a hydrogen atmosphere during sintering process. A large grain pellet can minimize fission gas release and deform easily at an elevated temperature. So, the recent development of nuclear fuel pellet materials is mainly focused on the large grain pellets. The various methods of fabrication processes for large grain UO{sub 2} pellets have been investigated extensively. Those parameters include the additives, sintering temperature, sintering time, sintering atmosphere, and so on. Cr-doped UO{sub 2} pellet is one of the promising candidates for PCI remedy. It was shown that the grain size and softness of UO{sub 2} pellets could be enhanced by doping Cr or Cr compound in UO{sub 2}. Various in-pile test results revealed that the PCI properties were enhanced considerably [4]. In the sintering process of Cr-doped UO{sub 2} pellet, it was known that tight adjusting of sintering atmosphere is most important to achieve large grain pellet. The relevant research revealed that the doped Cr{sub 2}O{sub 3} became liquid phase in optimized oxygen potential and that liquid phase promoted the grain growth. Recently, KAERI has shown that grain size of Cr-doped UO{sub 2} pellet could be more enlarged by adjusting process parameters. In this paper, we introduced a sintering process which can form a liquid phase for a large grain growth in Cr{sub 2}O{sub 3} doped UO{sub 2} pellet. The study on the effect of dwell time in H{sub 2} atmosphere during sintering process on the grain structure of sintered pellet is also a part of this work. In order to obtain large grain in pellet, it is important to increase amount of Cr that can form a liquid phase for grain growth by increasing dwell time in a hydrogen atmosphere during sintering process.

Experimental Study of Dust Grain Charging

Science.gov (United States)

Spann, James F; Venturini, Catherine C.; Comfort, Richard H.; Mian, Abbas M.

1999-01-01

The results of an experimental study of the charging mechanisms of micron size dust grains are presented. Individual dust grains are electrodynamically suspended and exposed to an electron beam of known energy and flux, and to far ultraviolet radiation of known wavelength and intensity. Changes in the charge-to-mass ratio of the grain are directly measured as a function of incident beam (electron and/or photon), grain size and composition. Comparisons of our results to theoretical models that predict the grain response are presented.

Proteomics analysis of maize (Zea mays L.) grain based on iTRAQ reveals molecular mechanisms of poor grain filling in inferior grains.

Science.gov (United States)

Yu, Tao; Li, Geng; Liu, Peng; Dong, Shuting; Zhang, Jiwang; Zhao, Bin

2017-06-01

In maize, inferior grains (IG) located on the upper part of the ear have poor grain filling process compared to superior grains (SG) located on the middle and lower parts of the ear. This difference limits satisfactory yield and quality; however, the underlying molecular mechanisms remain unknown. Here, using the isobaric tag for relative and absolute quantification (iTRAQ) technology, the proteomes of IG and SG during early and middle grain filling stages were investigated. In total, 4720 proteins were identified in maize grain and 305 differentially accumulated proteins (DiAPs) were detected between IG and SG. These DiAPs were involved in diverse cellular and metabolic processes with preferred distribution in protein synthesis/destination and metabolism. Compared to SG, DiAPs related to cell growth/division and starch synthesis were lag-accumulated and down-regulated in IG, respectively, resulting in smaller sink sizes and lower sink activities in IG. Meanwhile, impediment of the glycolysis pathway in IG may lead to reduce energy supply and building materials for substance synthesis. Additionally, reactive oxygen species (ROS) homeostasis and the defense system were disturbed in IG, which might lead to reduce protection against various environmental stresses. The present study provides new information on the proteomic differences between IG and SG, and explains possible molecular mechanisms for poor grain filling in IG. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Simulating the Probability of Grain Sorghum Maturity before the First Frost in Northeastern Colorado

Directory of Open Access Journals (Sweden)

Gregory S. McMaster

2016-09-01

Full Text Available Expanding grain sorghum [Sorghum bicolor (L. Moench] production northward from southeastern Colorado is thought to be limited by shorter growing seasons due to lower temperatures and earlier frost dates. This study used a simulation model for predicting crop phenology (PhenologyMMS to estimate the probability of reaching physiological maturity before the first fall frost for a variety of agronomic practices in northeastern Colorado. Physiological maturity for seven planting dates (1 May to 12 June, four seedbed moisture conditions affecting seedling emergence (from Optimum to Planted in Dust, and three maturity classes (Early, Medium, and Late were simulated using historical weather data from nine locations for both irrigated and dryland phenological parameters. The probability of reaching maturity before the first frost was slightly higher under dryland conditions, decreased as latitude, longitude, and elevation increased, planting date was delayed, and for later maturity classes. The results provide producers with estimates of the reliability of growing grain sorghum in northeastern Colorado.

Workers of Acromyrmex echinatior leafcutter ants police worker-laid eggs, but not reproductive workers

DEFF Research Database (Denmark)

Dijkstra, Michiel B.; van Zweden, Jelle Stijn; Dirchsen, Maria

2010-01-01

Nonreproductive workers of many eusocial Hymenoptera 'police' the colony, that is, they attack reproductive sister workers or destroy their eggs (unfertilized; developing into haploid males). Several ultimate causes of policing have been proposed, including (1) an increase in colony productivity,...... reproductive workers. We infer that relatedness incentives are the most likely ultimate cause of the evolutionary maintenance of worker-egg policing in A. echinatior. (C) 2010 The Association for the Study of Animal Behaviour. Published by Elsevier Ltd. All rights reserved...

Alignment of dust grains in ionized regions

Science.gov (United States)

Anderson, Nels; Watson, William D.

1993-01-01

The rate at which charged dust grains in a plasma are torqued by passing ions and electrons is calculated. When photo-emission of electrons is not important, attraction of ions by the grain monopole potential increases the rate at which the grains' spins are dealigned by nearly an order of magnitude. Consequently, the energy density of the magnetic field required to align grains in an H II region may be increased by about an order of magnitude. In contrast, electric dipole and quadrupole moments are unlikely to produce large dealignment rates for grains of modest length-to-width ratio. Nonetheless, for positively charged grains these higher-order moments likely prevent monopole repulsion of ions from reducing the dealignment rate far below that for neutral grains. The presence of positive grain charge therefore does not greatly facilitate grain alignment in an H II region.

Establishment of Grain Farmers' Supply Response Model and Empirical Analysis under Minimum Grain Purchase Price Policy

OpenAIRE

Zhang, Shuang

2012-01-01

Based on farmers' supply behavior theory and price expectations theory, this paper establishes grain farmers' supply response model of two major grain varieties (early indica rice and mixed wheat) in the major producing areas, to test whether the minimum grain purchase price policy can have price-oriented effect on grain production and supply in the major producing areas. Empirical analysis shows that the minimum purchase price published annually by the government has significant positive imp...

Comparative characteristics of grain classifications of soft wheat of Kazakhstan and major grain-producing countries

Directory of Open Access Journals (Sweden)

D. A. Shaimerdenova

2018-01-01

Full Text Available Soft wheat is one of the most important crops, grown in more than 130 countries. To date, one-fifth of the world's wheat, or about 150 million tons a year, is sold on international markets. In the world trade traditionally dominated by the US, Australia, Canada and Argentina. Kazakhstan, being on the 15th place in the production of wheat grain, is among the first ten exporters - in 2017 the country exported about 8 million tons to the amount of 1.5 billion dollars. USA, then, as potential export opportunities are much higher, as evidenced by annual carryover stocks at 3 million tons. According to experts, considerable differences in the classification of wheat grain used in Kazakhstan and in other countries participating in the grain market and the methods for assessing the technological dignity indicators (TDs laid down in the classifications are a significant obstacle to increasing the export potential of wheat grains. In view of this, an analysis was made of grain classifications of wheat grains used in the most important grain producing countries, TD indicators were determined, methods for their evaluation, and differences were revealed. It is established that in countries that are stable in the quantitative and qualitative characteristics of grain, an insignificant list of TD indicators is adopted, while they characterize the physical quality and state of the grain, which may indicate a general suitability for grinding. It is determined that in Russia and Kazakhstan, in determining the contamination, such an indicator as dockage is not taken into account. Comparative tests of different methods of sampling and determination of contamination have been carried out, and correlation coefficients have been established between indicators of contamination determined by different methods.

Abnormal grain growth: a non-equilibrium thermodynamic model for multi-grain binary systems

Czech Academy of Sciences Publication Activity Database

Svoboda, Jiří; Fischer, F. D.

2014-01-01

Roč. 22, č. 1 (2014), Art . No. 015013 ISSN 0965-0393 Institutional support: RVO:68081723 Keywords : grain boundary segregation * abnormal grain growth * theory * modelling * solute drag Subject RIV: BJ - Thermodynamics Impact factor: 2.167, year: 2014

Suprathermal grains: on intergalactic magnetic fields

International Nuclear Information System (INIS)

Dasgupta, A.K.

1979-01-01

Charged dust grains of radii a approximately equal to 3 x 10 -6 to approximately 3 x 10 -5 cm may be driven out of the galaxy due to radiation pressure of starlight. Once clear of the main gas-dust layer, dust grains may then escape into intergalactic space. Such grains are virtually indestructible-being evaporated only during formation. The dust grains, once injected into the intergalactic medium, may acquire suprathermal energy, thus 'suprathermal grains' in collision with magnetized cloud by the Fermi process. In order to attain relativistic energy, suprathermal grains have to move in and out ('scattering') of the magnetic field of the medium. It is now well established that high energy cosmic rays are of the order 10 20 eV or more. It has been speculated that these high energy (> = 10 18 eV) cosmic ray particles are charged dust grains, of intergalactic origin. This is possible only if there exists a magnetic field in the intergalactic medium. (Auth.)

Biogas production from brewery spent grain enhanced by bioaugmentation with hydrolytic anaerobic bacteria.

Science.gov (United States)

Čater, Maša; Fanedl, Lijana; Malovrh, Špela; Marinšek Logar, Romana

2015-06-01

Lignocellulosic substrates are widely available but not easily applied in biogas production due to their poor anaerobic degradation. The effect of bioaugmentation by anaerobic hydrolytic bacteria on biogas production was determined by the biochemical methane potential assay. Microbial biomass from full scale upflow anaerobic sludge blanket reactor treating brewery wastewater was a source of active microorganisms and brewery spent grain a model lignocellulosic substrate. Ruminococcus flavefaciens 007C, Pseudobutyrivibrio xylanivorans Mz5(T), Fibrobacter succinogenes S85 and Clostridium cellulovorans as pure and mixed cultures were used to enhance the lignocellulose degradation and elevate the biogas production. P. xylanivorans Mz5(T) was the most successful in elevating methane production (+17.8%), followed by the coculture of P. xylanivorans Mz5(T) and F. succinogenes S85 (+6.9%) and the coculture of C. cellulovorans and F. succinogenes S85 (+4.9%). Changes in microbial community structure were detected by fingerprinting techniques. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Prevalence of hepatitis C virus and excessive consumption of alcohol in a nonhospital worker population].

Science.gov (United States)

Prieto Domingo, J J; Carrión Bolaños, J A; Bandrés Moya, F

1997-12-01

The aim of the study was to know the prevalence of the hepatitis C virus (HCV) in a non hospital work population by ELISA 3.0 and PCR-Amplicor, as well as its relationship with excessive alcohol intake (more than 280 g/week in men and 168 g/week in women). A transversal seroepidemiologic study was carried out in 1,109 workers of the Empresa Nacional de Electricidad, S.A. (ENDESA). During the annual medical examinations (April 1993-October 1994) the amount of alcoholic beverages each worker had consumed over the 7 days prior to the medical examination was obtained by anamnesis together with a blood sample for different laboratory tests. Sixteen percent of the workers had had excessive alcohol intake. The prevalence of anti HCV antibodies in the study population was 2.4% being up to 4.6% in the workers declaring excessive alcohol consumption and 10.4% if they also presented an elevation in any of the transaminases. The prevalence of the potentially ineffective workers was 1.46%. The prevalence of anti C antibodies by ELISA 3.0 was greater than expected (2.4%) significantly increasing in the population group which declared excessive alcohol intake, thereby demonstrating the relationship between alcohol and hepatitis C.

The effect of grain boundary chemistry on the slip transmission process through grain boundaries in Ni3Al

International Nuclear Information System (INIS)

Robertson, I.M.; Lee, T.C.; Subramanian, R.; Birnbaum, H.K.

1992-01-01

This paper reports on the conditions established in disordered FCC systems for predicting the slip system that will be activated by a grain boundary to relieve a local stress concentration that have been applied to the ordered FCC alloy Ni 3 Al. The slip transfer behavior in hypo-stoichiometric Ni 3 Al with (0.2 at. %B) and without boron was directly observed by performing the deformation experiments in situ in the transmission electron microscope. In the boron-free and boron-doped alloys, lattice dislocations were incorporated in the grain boundary, but did not show evidence of dissociation to grain boundary dislocations or of movement in the grain boundary plane. The stress concentration associated with the dislocation pileup at the grain boundary are relieved by the emission of dislocations from the grain boundary in the boron-doped alloy. The slip system initiated in the adjoining grain obeyed the conditions established for disordered FCC systems. In the boron-free alloy, the primary stress relief mechanism was grain-boundary cracking, although dislocation emission from the grain boundary also occurred and accompanied intergranular crack advance

Dislocation polymorphism transformation of 6061-T651 aluminum alloy processed by laser shock processing: Effect of tempering at the elevated temperatures

International Nuclear Information System (INIS)

Ren, X.D.; Ruan, L.; Yuan, S.Q.; Ren, N.F.; Zheng, L.M.; Zhan, Q.B.; Zhou, J.Z.; Yang, H.M.; Wang, Y.; Dai, F.Z.

2013-01-01

The effects of tempering on surface topography and dislocation configuration of 6061-T651 aluminum alloy by laser shock processing (LSP) were investigated at the elevated temperatures. Surface topography and surface roughness were tested by a Surfcom 130A-Monochrome surface rough-meter. Morphologies of precipitated phases were monitored by scanning electron microscopy (SEM), and the dislocation configurations of samples after LSP were characterized by transmission electron microscope (TEM). The results showed that LSP had a beneficial effect on micro-hardness at elevated temperature. There was a little change of the surface roughness as subjected to LSP. The main strengthening mechanism of micro-hardness was dislocation strengthening and fine grain strengthening, and precipitated phase strengthening was the main strengthening mechanism at elevated temperature. “Dislocation polymorphism transformation” (DPT) effect was affirmed at elevated temperature, and the elevated temperature was principal element for inducing the DPT effect of 6061-T651 aluminum alloy by LSP

Computer simulation of grain growth in HAZ

Science.gov (United States)

Gao, Jinhua

Two different models for Monte Carlo simulation of normal grain growth in metals and alloys were developed. Each simulation model was based on a different approach to couple the Monte Carlo simulation time to real time-temperature. These models demonstrated the applicability of Monte Carlo simulation to grain growth in materials processing. A grain boundary migration (GBM) model coupled the Monte Carlo simulation to a first principle grain boundary migration model. The simulation results, by applying this model to isothermal grain growth in zone-refined tin, showed good agreement with experimental results. An experimental data based (EDB) model coupled the Monte Carlo simulation with grain growth kinetics obtained from the experiment. The results of the application of the EDB model to the grain growth during continuous heating of a beta titanium alloy correlated well with experimental data. In order to acquire the grain growth kinetics from the experiment, a new mathematical method was developed and utilized to analyze the experimental data on isothermal grain growth. Grain growth in the HAZ of 0.2% Cu-Al alloy was successfully simulated using the EDB model combined with grain growth kinetics obtained from the experiment and measured thermal cycles from the welding process. The simulated grain size distribution in the HAZ was in good agreement with experimental results. The pinning effect of second phase particles on grain growth was also simulated in this work. The simulation results confirmed that by introducing the variable R, degree of contact between grain boundaries and second phase particles, the Zener pinning model can be modified as${D/ r} = {K/{Rf}}$where D is the pinned grain size, r the mean size of second phase particles, K a constant, f the area fraction (or the volume fraction in 3-D) of second phase.

MATHEMATICAL MODEL OF GRAIN MICRONIZATION

Directory of Open Access Journals (Sweden)

V. A. Afanas’ev

2014-01-01

Full Text Available Summary. During micronisation grain moisture evaporates mainly in decreasing drying rate period. Grain layer located on the surface of the conveyor micronisers will be regarded as horizontal plate. Due to the fact that the micronisation process the surface of the grain evaporates little moisture (within 2-7 % is assumed constant plate thickness. Because in the process of micronization grain structure is changing, in order to achieve an exact solution of the equations necessary to take into account changes thermophysical, optical and others. Equation of heat transfer is necessary to add a term that is responsible for the infrared heating. Because of the small thickness of the grain, neglecting the processes occurring at the edge of the grain, that is actually consider the problem of an infinite plate. To check the adequacy of the mathematical model of the process of micronisation of wheat grain moisture content must be comparable to the function of time, obtained by solving the system of equations with the measured experimental data of experience. Numerical solution of a system of equations for the period of decreasing drying rate is feasible with the help of the Maple 14, substituting the values of the constants in the system. Calculation of the average relative error does not exceed 7- 10 %, and shows a good agreement between the calculated data and the experimental values.

CO2-Induced Changes in Wheat Grain Composition: Meta-Analysis and Response Functions

Directory of Open Access Journals (Sweden)

Malin C. Broberg

2017-04-01

Full Text Available Elevated carbon dioxide (eCO2 stimulates wheat grain yield, but simultaneously reduces protein/nitrogen (N concentration. Also, other essential nutrients are subject to change. This study is a synthesis of wheat experiments with eCO2, estimating the effects on N, minerals (B, Ca, Cd, Fe, K, Mg, Mn, Na, P, S, Zn, and starch. The analysis was performed by (i deriving response functions to assess the gradual change in element concentration with increasing CO2 concentration, (ii meta-analysis to test the average magnitude and significance of observed effects, and (iii relating CO2 effects on minerals to effects on N and grain yield. Responses ranged from zero to strong negative effects of eCO2 on mineral concentration, with the largest reductions for the nutritionally important elements of N, Fe, S, Zn, and Mg. Together with the positive but small and non-significant effect on starch concentration, the large variation in effects suggests that CO2-induced responses cannot be explained only by a simple dilution model. To explain the observed pattern, uptake and transport mechanisms may have to be considered, along with the link of different elements to N uptake. Our study shows that eCO2 has a significant effect on wheat grain stoichiometry, with implications for human nutrition in a world of rising CO2.

Genetic dissection of grain size and grain number trade-offs in CIMMYT wheat germplasm.

Science.gov (United States)

Griffiths, Simon; Wingen, Luzie; Pietragalla, Julian; Garcia, Guillermo; Hasan, Ahmed; Miralles, Daniel; Calderini, Daniel F; Ankleshwaria, Jignaben Bipinchandra; Waite, Michelle Leverington; Simmonds, James; Snape, John; Reynolds, Matthew

2015-01-01

Grain weight (GW) and number per unit area of land (GN) are the primary components of grain yield in wheat. In segregating populations both yield components often show a negative correlation among themselves. Here we use a recombinant doubled haploid population of 105 individuals developed from the CIMMYT varieties Weebill and Bacanora to understand the relative contribution of these components to grain yield and their interaction with each other. Weebill was chosen for its high GW and Bacanora for high GN. The population was phenotyped in Mexico, Argentina, Chile and the UK. Two loci influencing grain yield were indicated on 1B and 7B after QTL analysis. Weebill contributed the increasing alleles. The 1B effect, which is probably caused by to the 1BL.1RS rye introgression in Bacanora, was a result of increased GN, whereas, the 7B QTL controls GW. We concluded that increased in GW from Weebill 7B allele is not accompanied by a significant reduction in grain number. The extent of the GW and GN trade-off is reduced. This makes this locus an attractive target for marker assisted selection to develop high yielding bold grain varieties like Weebill. AMMI analysis was used to show that the 7B Weebill allele appears to contribute to yield stability.

Spinodal decomposition in fine grained materials

Indian Academy of Sciences (India)

Unknown

ηηi has a value of unity inside the ith grain, decreases smoothly through the grain boundary region to zero out- side the grain. For a symmetric alloy of composition, c = 0⋅⋅5, our results show that microstructural evolution depends largely on the difference in the grain boundary energies, γγgb, of A-rich (αα) and B-rich (ββ) ...

Relationship between mutation frequency of GPA locus and cumulative dose among medical diagnostic X-ray workers

International Nuclear Information System (INIS)

Wang Jixian; Yu Wenru; Li Benxiao; Fan Tiqiang; Li Zhen; Gao Zhiwei; Chen Zhenjun; Zhao Yongcheng

2000-01-01

Objective: To explore the feasibility of using GPA locus mutation assay as a bio-dosimeter for occupational exposure to ionizing radiation. Methods: An improved technique of GPA locus mutation assay was used in th study. The frequencies of mutant RBC in peripheral blood of 55 medical X-ray workers and 50 controls employed in different calendar-year periods were detected. The relationship between mutation frequencies (MFs) and period of entry, working years and cumulative doses were analyzed. Results: The MFs were significantly elevated among X-ray workers employed before 1970. This finding is similar to the result of cancer epidemiological study among medical X-ray workers , in which the cancer risk was significantly increased only X-ray workers employed before 1970. The MFs of GPA increased with increasing cumulative dose. The dose-effect relationship of Nφ MF with cumulative dose was closer than that of NN MF. Conclusion: There are many problems to be solved for using GPA MF assay as a bio-dosimeter such as individual variation, specificity and calibration curve of dose-effect relationship

Radiation disinfestation of grain

Energy Technology Data Exchange (ETDEWEB)

NONE

1962-10-15

A panel was convened by the International Atomic Energy Agency to consider ways of applying radiation to grain handling and insect control, and to make recommendations on the advisability and nature of any future action in this field. Among other subjects, the panel discussed the use of electron accelerators and gamma radiation for grain disinfestation as well as problems of radiation entomology and wholesomeness of irradiated grain. After reviewing the present state of knowledge regarding radiation disinfestation of grain, the experts agreed that pilot plant operations be initiated as soon as practicable in order to evaluate the use of irradiation plants under practical conditions in their entomological, engineering and economic aspects. They recommended that research effort be directed towards solving certain fundamental problems related to the proposed pilot plant projects; such as rapid methods for differentiation between sterile insects and normal ones; study of the metabolism of irradiated immature stages of insects in relation to the heating of treated grain; research into possible induction of radiation resistance; irradiation susceptibility of insects which show resistance to conventional insecticides; and study of methods of sensitizing insects to irradiation damage. It was also pointed out that the distribution of irradiated food for human consumption was controlled in most countries under present legislative procedures, and no country had yet approved radiation treatment of cereals. The experts recommended that countries in a position to submit evidence to their appropriate authorities regarding the wholesomeness of irradiated cereals should be encouraged to do so as soon as possible. Regarding the engineering aspects of irradiation pilot plant projects, the experts noted that the process could be automated and operated safely. Electron accelerators and cobalt sources could be used for all the throughput rates utilized in most conventional grain

Radiation disinfestation of grain

International Nuclear Information System (INIS)

1962-01-01

A panel was convened by the International Atomic Energy Agency to consider ways of applying radiation to grain handling and insect control, and to make recommendations on the advisability and nature of any future action in this field. Among other subjects, the panel discussed the use of electron accelerators and gamma radiation for grain disinfestation as well as problems of radiation entomology and wholesomeness of irradiated grain. After reviewing the present state of knowledge regarding radiation disinfestation of grain, the experts agreed that pilot plant operations be initiated as soon as practicable in order to evaluate the use of irradiation plants under practical conditions in their entomological, engineering and economic aspects. They recommended that research effort be directed towards solving certain fundamental problems related to the proposed pilot plant projects; such as rapid methods for differentiation between sterile insects and normal ones; study of the metabolism of irradiated immature stages of insects in relation to the heating of treated grain; research into possible induction of radiation resistance; irradiation susceptibility of insects which show resistance to conventional insecticides; and study of methods of sensitizing insects to irradiation damage. It was also pointed out that the distribution of irradiated food for human consumption was controlled in most countries under present legislative procedures, and no country had yet approved radiation treatment of cereals. The experts recommended that countries in a position to submit evidence to their appropriate authorities regarding the wholesomeness of irradiated cereals should be encouraged to do so as soon as possible. Regarding the engineering aspects of irradiation pilot plant projects, the experts noted that the process could be automated and operated safely. Electron accelerators and cobalt sources could be used for all the throughput rates utilized in most conventional grain

Grain boundary segregation and intergranular failure

International Nuclear Information System (INIS)

White, C.L.

1980-01-01

Trace elements and impurities often segregate strongly to grain boundaries in metals and alloys. Concentrations of these elements at grain boundaries are often 10 3 to 10 5 times as great as their overall concentration in the alloy. Because of such segregation, certain trace elements can exert a disproportionate influence on material properties. One frequently observed consequence of trace element segregation to grain boundaries is the occurrence of grain boundary failure and low ductility. Less well known are incidences of improved ductility and inhibition of grain boundary fracture resulting from trace element segregation to grain boundaries in certain systems. An overview of trace element segregation and intergranular failure in a variety of alloy systems as well as preliminary results from studies on Al 3% Li will be presented

Grain refinement of aluminum and its alloys

International Nuclear Information System (INIS)

Zaid, A.I.O.

2001-01-01

Grain refinement of aluminum and its alloys by the binary Al-Ti and Ternary Al-Ti-B master alloys is reviewed and discussed. The importance of grain refining to the cast industry and the parameters affecting it are presented and discussed. These include parameters related to the cast, parameters related to the grain refining alloy and parameters related to the process. The different mechanisms, suggested in the literature for the process of grain refining are presented and discussed, from which it is found that although the mechanism of refining by the binary Al-Ti is well established the mechanism of grain refining by the ternary Al-Ti-B is still a controversial matter and some research work is still needed in this area. The effect of the addition of other alloying elements in the presence of the grain refiner on the grain refining efficiency is also reviewed and discussed. It is found that some elements e.g. V, Mo, C improves the grain refining efficiency, whereas other elements e.g. Cr, Zr, Ta poisons the grain refinement. Based on the parameters affecting the grain refinement and its mechanism, a criterion for selection of the optimum grain refiner is forwarded and discussed. (author)

The effect of the Tom Thumb dwarfing gene on grain size and grain number of wheat (Triticum aestivum)

International Nuclear Information System (INIS)

Gale, M.D.; Flintham, J.E.

1984-01-01

The Tom Thumb dwarfing gene, Rht3, like the related genes Rht1 and Rht2 from Norin 10, has pleiotropic effects on individual ear yields, and grain protein concentrations. An experiment was conducted in which tiller number per plant and grain number per spike were restricted to ascertain whether reduced grain size and protein content are primary or secondary competitive effects in near-isogenic lines. The potential for grain growth was shown to be identical in Rht3 and rht genotypes when grain set was restricted, indicating that the primary effect of the gene is to increase spikelet fertility. Nitrogen accumulation within the grain was also affected by inter-grain competition but decreased nitrogen yields per plant indicated that reduced protein levels are, in part, a primary effect of the gene. Analysis of individual grain yields within Rht3 and rht spikes showed that the gene affected developmental 'dominance' relationships within the spike. (author)

SMALL GRAIN 1, which encodes a mitogen-activated protein kinase kinase 4, influences grain size in rice.

Science.gov (United States)

Duan, Penggen; Rao, Yuchun; Zeng, Dali; Yang, Yaolong; Xu, Ran; Zhang, Baolan; Dong, Guojun; Qian, Qian; Li, Yunhai

2014-02-01

Although grain size is one of the most important components of grain yield, little information is known about the mechanisms that determine final grain size in crops. Here we characterize rice small grain1 (smg1) mutants, which exhibit small and light grains, dense and erect panicles and comparatively slightly shorter plants. The short grain and panicle phenotypes of smg1 mutants are caused by a defect in cell proliferation. The smg1 mutations were identified, using a map-based cloning approach, in mitogen-activated protein kinase kinase 4 (OsMKK4). Relatively higher expression of OsMKK4/SMG1 was detected in younger organs than in older ones, consistent with its role in cell proliferation. Green fluorescent protein (GFP)-OsMKK4/SMG1 fusion proteins appear to be distributed ubiquitously in plant cells. Further results revealed that OsMKK4 influenced brassinosteroid (BR) responses and the expression of BR-related genes. Thus, our findings have identified OsMKK4 as a factor for grain size, and suggest a possible link between the MAPK pathways and BRs in grain growth. © 2013 The Authors The Plant Journal © 2013 John Wiley & Sons Ltd.

[Features of the lipid exchange in workers employed in aluminium productions].

Science.gov (United States)

Kudaeva, I V; Dyakovich, O A; Masnavieva, L B; Popkova, O V; Abramatets, E A

Aluminum production can be referred to the category of industries of the increased health hazard for the workers. During technological process of receiving aluminum the air of a working zone is polluted by a large number of harmful substances. Workers are exposed to the complex of toxicants possessing a polytropic impact on the body. The most significant consequences are violations of different types of metabolism in the organism, including lipid metabolism. The purpose of the study is the investigation of the state of lipid metabolism in persons working in the production of aluminum. The object of research was 108 male workers of aluminum production suffering from occupational pathology of airways. The group of comparison was consisted of 103 men, apparently healthy, not exposed to toxicants. There was determined the content of the total cholesterol (TC), high and low density lipoprotein cholesterol (HDLC and LDLC), triglycerides (TG), phospholipids (PL), atherogenic index (AI). Statistical processing was performed with the use of software «Statistica 6.0». There were established statistically significant differences of indices of lipid exchange in the persons occupied in aluminum production when related to the group of comparison. IA values in persons from the study group proved to be higher than in the comparison group, due to elevated levels of TC and LDLC. The TG and PL level was also higher. The values of IA, TC and TG in workers of aluminum production in more than 50% cases exceeded the reference values. The average concentration of HDL cholesterol in both groups did not differ, and was above the lower reference boundary. Established features of lipid metabolism in workers of aluminum allow us to suggest the distinction in mechanisms of developing proatherogenic disorders from previously established ones for workers exposed to other chemicals. One of the causes of the shaping of these disorders can be oxidative stress, which in turn serves as a response to

Response of the rhizosphere prokaryotic community of barley (Hordeum vulgare L.) to elevated atmospheric CO2 concentration in open-top chambers.

Science.gov (United States)

Szoboszlay, Márton; Näther, Astrid; Mitterbauer, Esther; Bender, Jürgen; Weigel, Hans-Joachim; Tebbe, Christoph C

2017-08-01

The effect of elevated atmospheric CO 2 concentration [CO 2 ] on the diversity and composition of the prokaryotic community inhabiting the rhizosphere of winter barley (Hordeum vulgare L.) was investigated in a field experiment, using open-top chambers. Rhizosphere samples were collected at anthesis (flowering stage) from six chambers with ambient [CO 2 ] (approximately 400 ppm) and six chambers with elevated [CO 2 ] (700 ppm). The V4 region of the 16S rRNA gene was PCR-amplified from the extracted DNA and sequenced on an Illumina MiSeq instrument. Above-ground plant biomass was not affected by elevated [CO 2 ] at anthesis, but plants exposed to elevated [CO 2 ] had significantly higher grain yield. The composition of the rhizosphere prokaryotic communities was very similar under ambient and elevated [CO 2 ]. The dominant taxa were Bacteroidetes, Actinobacteria, Alpha-, Gamma-, and Betaproteobacteria. Elevated [CO 2 ] resulted in lower prokaryotic diversity in the rhizosphere, but did not cause a significant difference in community structure. © 2017 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

Autonomous grain combine control system

Science.gov (United States)

Hoskinson, Reed L.; Kenney, Kevin L.; Lucas, James R.; Prickel, Marvin A.

2013-06-25

A system for controlling a grain combine having a rotor/cylinder, a sieve, a fan, a concave, a feeder, a header, an engine, and a control system. The feeder of the grain combine is engaged and the header is lowered. A separator loss target, engine load target, and a sieve loss target are selected. Grain is harvested with the lowered header passing the grain through the engaged feeder. Separator loss, sieve loss, engine load and ground speed of the grain combine are continuously monitored during the harvesting. If the monitored separator loss exceeds the selected separator loss target, the speed of the rotor/cylinder, the concave setting, the engine load target, or a combination thereof is adjusted. If the monitored sieve loss exceeds the selected sieve loss target, the speed of the fan, the size of the sieve openings, or the engine load target is adjusted.

The tensile behavior of GH3535 superalloy at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Han, F.F.; Zhou, B.M.; Huang, H.F.; Leng, B.; Lu, Y.L. [Thorium Molten Salts Reactor Center, Shanghai Institute of Applied Physics, Chinese Academy of Sciences (China); Dong, J.S. [Superalloy Division, Institute of Metal Research, Chinese Academy of Sciences (China); Li, Z.J., E-mail: lizhijun@sinap.ac.cn [Thorium Molten Salts Reactor Center, Shanghai Institute of Applied Physics, Chinese Academy of Sciences (China); Zhou, X.T. [Thorium Molten Salts Reactor Center, Shanghai Institute of Applied Physics, Chinese Academy of Sciences (China)

2016-10-01

The tensile behavior of GH3535 alloy has been investigated at strain rates of 8.33 × 10{sup −5}/s{sup −1}–8.33 × 10{sup −3}/s{sup −1}, in the temperature range of 25–800 °C. The results showed that the ultimate tensile strength was decreased with increasing temperature and increased with rising strain rate, whereas the yield strength kept almost a constant value at the temperature range from 550 to 800 °C in all strain rates test. The formation of M{sub 12}C carbides at the grain boundary during the tension process played an important role in increasing the yield strength of the alloy at elevated temperatures. But inhomogeneous deformation at 650 °C resulted in the minimum ductility of the alloy. Additionally, various types of serrations were noticed on the stress-strain curves for the alloy tested in the temperature range of 500–800 °C. Normal Portevin-Le Chatelier (PLC) effect and positive strain rate sensitivity were observed in this alloy. Type A and A + B serrations were presented to stress-strain curves at temperatures below 650 °C, whereas type C serration was noticed when the temperature rose above 650 °C. The analysis suggested that the interactions between substitutional solutes migration and mobile dislocations were the main reason for the serrated flow behavior in this alloy. - Highlights: • The tensile behavior of GH3535 alloy at elevated temperature was studied. • The yield strength anomaly was observed in the temperature range from 550 to 800 °C. • The formation of M{sub 12}C improves the grain boundary strength to a certain extent. • Inhomogeneous deformation at 650 °C results in the ductility loss of the alloy. • The interaction between solute atoms and dislocations results in the PLC effect.

The valuation of commercial grain silos

African Journals Online (AJOL)

The valuation of grain silos is a complex exercise when one considers all the variables that affect their ... their grains, larger grain-processing companies, traders, importers or exporters that have ..... 2015: personal interview). The percentages ...

Mortality experience among Minnesota taconite mining industry workers.

Science.gov (United States)

Allen, Elizabeth M; Alexander, Bruce H; MacLehose, Richard F; Ramachandran, Gurumurthy; Mandel, Jeffrey H

2014-11-01

To evaluate the mortality experience of Minnesota taconite mining industry workers. Mortality was evaluated between 1960 and 2010 in a cohort of Minnesota taconite mining workers employed by any of the seven companies in operation in 1983. Standardised mortality ratios (SMR) were estimated by comparing observed deaths in the cohort with expected frequencies in the Minnesota population. Standardised rate ratios (SRR) were estimated using an internal analysis to compare mortality by employment duration. The cohort included 31,067 workers with at least 1 year of documented employment. Among those, there were 9094 deaths, of which 949 were from lung cancer, and 30 from mesothelioma. Mortality from all causes was greater than expected in the Minnesota population (SMR=1.04, 95% CI 1.02 to 1.04). Mortality from lung cancer and mesothelioma was higher than expected with SMRs of 1.16 for lung cancer (95% CI 1.09 to 1.23) and 2.77 for mesothelioma (95% CI 1.87 to 3.96). Other elevated SMRs included those for cardiovascular disease (SMR=1.10, 95% CI 1.06 to 1.14), specifically for hypertensive heart disease (SMR=1.81, 95% CI 1.39 to 2.33) and ischemic heart disease (SMR=1.11, 95% CI 1.07 to 1.16). Results of the SRR analysis did not show variation in risk by duration of employment. This study provides evidence that taconite workers may be at increased risk for mortality from lung cancer, mesothelioma, and some cardiovascular disease. Occupational exposures during taconite mining operations may be associated with these increased risks, but non-occupational exposures may also be important contributors. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Grain formation in cool stellar envelopes

International Nuclear Information System (INIS)

Deguchi, S.

1980-01-01

The nucleation and growth of dust grains in the stellar envelope are investigated for the case of oxygen-rich stars, where the mass loss occurs as a result of the radiation pressure on the dust grains. The number density of grains, the final grain sizes, and the final amount of metals remaining in gaseous states are calculated based on the grain-nucleation theory proposed by Yamamoto and Hasegawa and Draine and Salpeter. It is shown that, even if we base our calculations on the Lothe-Pound nucleation rate equation instead of the classical, homogeneous nucleation rate equation, the proposed theory gives a number density of grains quite similar to that based on the classical rate equation. The approximate solution of the flow, in this paper, brings physical insight to the problem of how the formation of grains couples the flow passing the sonic point. The metals in the outer envelope remain in gaseous state by the amount of 1--10% of the initial content for the mass-loss rate of 10 -5 M/sub sun/ yr -1 and by less than 1% for the massloss are less than 3 x 10 -6 M/sub sun/ yr -1 . Species of metals condensed onto the grains are also discussed

Deformation strain inhomogeneity in columnar grain nickel

DEFF Research Database (Denmark)

Wu, G.L.; Godfrey, A.; Juul Jensen, D.

2005-01-01

A method is presented for determination of the local deformation strain of individual grains in the bulk of a columnar grain sample. The method, based on measurement of the change in grain area of each grain, is applied to 12% cold rolled nickel. Large variations are observed in the local strain...... associated with each grain. (c) 2005 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved....

Impact of Phosphorus Levels and Seed Rates on Growth and Yield of Late Sown Maize on High Elevation in Swat, Pakistan

International Nuclear Information System (INIS)

Imran, M.; Khan, A. A.; Khattak, I.; Naveed, S.

2015-01-01

After nitrogen, phosphorus (P) is required by the plants relatively in large quantity and is the second most important crop nutrient that increases productivity of maize (Zea mays L.). An experiment on effect of different P/sub 2/O/sub 5/ levels and seed rates on growth and yield of late sown maize cv. Baber on high elevation during kharif season, was conducted at Farmer Field School, Swat, Pakistan during summer 2012. The experiment was laid out in randomized complete block design having three replications. Sowing was done one month late (July 15) than the optimum time of sowing. Optimum time of sowing on high elevation in Swat, Pakistan starts from May 15 to June 15. Four levels of P/sub 2/O/sub 5/(0, 25, 50 and 75 kg ha/sup -1/) and four seed rates (10, 20, 30 and 40 kg ha/sup -1/) were used. A subplot size of 3m x 4.5m was used. Each subplot was consisted of six rows having 75 cm row-to-row distance with row length of 3 m. Sowing of 40 kg seed ha/sup -1/ treated with 75kg P/sub 2/O/sub 5/ ha/sup -1/ gave optimum cob length (19 cm), plant height (179.19 cm), 1000 grain weight (192.83 g) and grain yield (2712 kg ha/sup -1/). While maximum grain cob/sup -1/(375 ) was given by 30 kg seed ha/sup -1/ treated with 75 kg P/sub 2/O/sub 5/. On the basis of the above results, among the tested seed rate 40 kg ha/sup -1/ treated with 75 kg P/sub 2/O/sub 5/ is recommended for late sowing on high elevation under the agro-ecological conditions of Swat valley. (author)

Fine grained event processing on HPCs with the ATLAS Yoda system

CERN Document Server

Calafiura, Paolo; The ATLAS collaboration; Guan, Wen; Maeno, Tadashi; Nilsson, Paul; Oleynik, Danila; Panitkin, Sergey; Tsulaia, Vakhtang; van Gemmeren, Peter; Wenaus, Torre

2015-01-01

High performance computing facilities present unique challenges and opportunities for HENP event processing. The massive scale of many HPC systems means that fractionally small utilizations can yield large returns in processing throughput. Parallel applications which can dynamically and efficiently fill any scheduling opportunities the resource presents benefit both the facility (maximal utilization) and the (compute-limited) science. The ATLAS Yoda system provides this capability to HENP-like event processing applications by implementing event-level processing in an MPI-based master-client model that integrates seamlessly with the more broadly scoped ATLAS Event Service. Fine grained, event level work assignments are intelligently dispatched to parallel workers to sustain full utilization on all cores, with outputs streamed off to destination object stores in near real time with similarly fine granularity, such that processing can proceed until termination with full utilization. The system offers the efficie...

Randomly grain growth in metallic materials

Energy Technology Data Exchange (ETDEWEB)

Ramirez, A. [Instituto Politecnico Nacional, (SEPI-ESIME), Unidad Profesional Ticoman, Av. Ticoman 600, Del. G.A.M., C.P. 07340 Distrito Federal, Mexico (Mexico); Instituto Politecnico Nacional, (SEPI-ESIQIE), Unidad Profesional Zacatenco, Edif. 6 y Edif. Z planta baja C.P.07300, Distrito Federal, Mexico (Mexico)], E-mail: adaramil@yahoo.com.mx; Chavez, F. [Instituto Politecnico Nacional, (SEPI-ESIQIE), Unidad Profesional Zacatenco, Edif. 6 y Edif. Z planta baja C.P.07300, Distrito Federal, Mexico (Mexico); Demedices, L. [Instituto Politecnico Nacional, (SEPI-ESIME), Unidad Profesional Ticoman, Av. Ticoman 600, Del. G.A.M., C.P. 07340 Distrito Federal, Mexico (Mexico); Instituto Politecnico Nacional, (SEPI-ESIQIE), Unidad Profesional Zacatenco, Edif. 6 y Edif. Z planta baja C.P.07300, Distrito Federal, Mexico (Mexico); Cruz, A.; Macias, M. [Instituto Politecnico Nacional, (SEPI-ESIQIE), Unidad Profesional Zacatenco, Edif. 6 y Edif. Z planta baja C.P.07300, Distrito Federal, Mexico (Mexico)

2009-10-30

Computational modeling of grain structures is a very important topic in materials science. In this work, the development of the computational algorithms for a mathematical model to predict grain nucleation and grain growth is presented. The model place a number of nucleated points randomly in a liquid pool according with the solid and liquid fractions (X{sub sol} and X{sub liq}) of metal solute and the local temperature distribution (SS{sub I,J}). Then these points grows isotropically until obtain a grain structure with straight interfaces. Different grain morphologies such as columnar and equiaxed can be obtained as a function of the temperature distributions and growth directions.

Randomly grain growth in metallic materials

International Nuclear Information System (INIS)

Ramirez, A.; Chavez, F.; Demedices, L.; Cruz, A.; Macias, M.

2009-01-01

Computational modeling of grain structures is a very important topic in materials science. In this work, the development of the computational algorithms for a mathematical model to predict grain nucleation and grain growth is presented. The model place a number of nucleated points randomly in a liquid pool according with the solid and liquid fractions (X sol and X liq ) of metal solute and the local temperature distribution (SS I,J ). Then these points grows isotropically until obtain a grain structure with straight interfaces. Different grain morphologies such as columnar and equiaxed can be obtained as a function of the temperature distributions and growth directions.

Deformation behavior of multilayered NiFe with bimodal grain size distribution at room and elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Fiebig, Jochen, E-mail: jmfiebig@ucdavis.edu [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95817 (United States); Jian, Jie [Department of Electrical and Computer Engineering, Texas A& M University, College Station, TX 77843-3128 (United States); Kurmanaeva, Lilia [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95817 (United States); McCrea, Jon [Integran Technologies Inc., Toronto (Canada); Wang, Haiyan [Department of Electrical and Computer Engineering, Texas A& M University, College Station, TX 77843-3128 (United States); Lavernia, Enrique [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95817 (United States); Department of Chemical Engineering and Materials Science, University of California, Irvine, CA 92697 (United States); Mukherjee, Amiya [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95817 (United States)

2016-02-22

We describe a study of the temperature dependent deformation behavior of a multilayered NiFe-60 wt%Fe alloy with a layer thickness of 5 μm fabricated by electrodeposition. The structure of adjacent layers alternates between a nanocrystalline and a coarse grained. Uniaxial tensile tests at temperature between 20 °C and 400 °C and strain rate of 10{sup −4}–10{sup −2} were used to determine the mechanical behavior. Microstructure observations via transmission electron microscopy and fractography were performed to provide insight into the underlying deformation mechanism. The mechanical behavior is discussed in the context of the bimodal microstructure of multilayered samples and the contribution of each sub-layer to strength and ductility. The results reveal that even at higher temperatures the nanocrystalline layer determines the mechanical performance of multilayered materials.

Blood Pressure of Jordanian Workers Chronically Exposed to Noise in Industrial Plants

Directory of Open Access Journals (Sweden)

Saed Nserat

2017-10-01

Full Text Available Background: Occupational studies investigating the association between blood pressure and noise exposure are almost lacking in the Eastern Mediterranean Region countries. Objective: To determine the association between occupational exposure to high level of noise and blood pressure among a group of workers in Jordan. Methods: All workers who had been exposing to noise for at least 3 years in 3 plants in Madaba governorate in Jordan were included in this cross-sectional study. A structured questionnaire was used to collect data. The occupational noise level was measured with a portable calibrated sound meter. Results: We studied 191 male workers, of whom 145 (75.9% were exposed to a noise level higher than the permissible limit of 85 dBA. The mean systolic blood pressure (SBP and diastolic blood pressure (DBP and the prevalence of hypertension were significantly higher among those exposed to higher noise level. In multivariate analysis, workers exposed to high level of noise had a significantly higher odds of hypertension compared to those exposed to noise level lower than the permissible limit (OR 4.7, 95% CI 1.6 to 13.8. The odds of hypertension increased by 17% (95% CI 10% to 30% for each dB increase in noise intensity. Conclusion: Exposure to high level of noise is associated with elevated blood pressure.

Normal and abnormal grain growth in fine-grained Nd-Fe-B sintered magnets prepared from He jet milled powders

Energy Technology Data Exchange (ETDEWEB)

Bittner, F., E-mail: f.bittner@ifw-dresden.de [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany); Technische Universität Dresden, Institute of Materials Science, 01062 Dresden (Germany); Woodcock, T.G. [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany); Schultz, L. [IFW Dresden, Institute for Metallic Materials, PO Box 270116, 01171 Dresden (Germany); Technische Universität Dresden, Institute of Materials Science, 01062 Dresden (Germany); Schwöbel, C. [Technische Universität Darmstadt, Materialwissenschaft, Alarich-Weiß-Str. 16, 64287 Darmstadt (Germany); Gutfleisch, O. [Technische Universität Darmstadt, Materialwissenschaft, Alarich-Weiß-Str. 16, 64287 Darmstadt (Germany); Fraunhofer ISC, Projektgruppe für Werkstoffkreisläufe und Ressourcenstrategie IWKS, Rodenbacher Chaussee 4, 63457 Hanau (Germany); Zickler, G.A.; Fidler, J. [Technische Universität Wien, Institute of Solid State Physics, Wiedner Hauptstr. 8-10, 1040 Wien (Austria); Üstüner, K.; Katter, M. [Vacuumschmelze GmbH & Co. KG, 63412 Hanau (Germany)

2017-03-15

Fine-grained, heavy rare earth free Nd-Fe-B sintered magnets were prepared from He jet milled powders with an average particle size of 1.5 µm by low temperature sintering at 920 °C or 980 °C. A coercivity of >1600 kA/m was achieved for an average grain size of 1.68 µm. Transmission electron microscopy showed that the distribution and composition of intergranular and grain boundary junction phases was similar to that in conventionally processed magnets. Microstructural analysis on different length scales revealed the occurrence of abnormal grain growth, which is unexpected for sintering temperatures below 1000 °C. A larger area fraction of abnormal grains was observed in the sample sintered at 920 °C compared to that sintered at 980 °C. Microtexture investigation showed a better crystallographic alignment of the abnormal grains compared to the fine-grained matrix, which is explained by a size dependent alignment of the powder particles during magnetic field alignment prior to sintering. Slightly larger particles in the initial powder show a better alignment and will act as nucleation sites for abnormal grain growth. Magneto-optical Kerr investigations confirmed the lower switching field of the abnormal grains compared to the fine-grained matrix. The demagnetisation curve of the sample sintered at 920 °C showed reduced rectangularity and this was attributed to a cooperative effect of the larger fraction of abnormal grains with low switching field and, as a minor effect, a reduced degree of crystallographic texture in this sample compared to the material sintered at 980 °C, which did not show the reduced rectangularity of the demagnetisation curve. - Highlights: • He Jet milling to reduce Nd-Fe-B grain size and to enhance coercivity. • Normal and abnormal grain growth observed for low temperature sintering. • Well oriented abnormal grown grains explained by size dependent field alignment. • Poor rectangularity is caused by low nucleation field of

Normal and abnormal grain growth in fine-grained Nd-Fe-B sintered magnets prepared from He jet milled powders

International Nuclear Information System (INIS)

Bittner, F.; Woodcock, T.G.; Schultz, L.; Schwöbel, C.; Gutfleisch, O.; Zickler, G.A.; Fidler, J.; Üstüner, K.; Katter, M.

2017-01-01

Fine-grained, heavy rare earth free Nd-Fe-B sintered magnets were prepared from He jet milled powders with an average particle size of 1.5 µm by low temperature sintering at 920 °C or 980 °C. A coercivity of >1600 kA/m was achieved for an average grain size of 1.68 µm. Transmission electron microscopy showed that the distribution and composition of intergranular and grain boundary junction phases was similar to that in conventionally processed magnets. Microstructural analysis on different length scales revealed the occurrence of abnormal grain growth, which is unexpected for sintering temperatures below 1000 °C. A larger area fraction of abnormal grains was observed in the sample sintered at 920 °C compared to that sintered at 980 °C. Microtexture investigation showed a better crystallographic alignment of the abnormal grains compared to the fine-grained matrix, which is explained by a size dependent alignment of the powder particles during magnetic field alignment prior to sintering. Slightly larger particles in the initial powder show a better alignment and will act as nucleation sites for abnormal grain growth. Magneto-optical Kerr investigations confirmed the lower switching field of the abnormal grains compared to the fine-grained matrix. The demagnetisation curve of the sample sintered at 920 °C showed reduced rectangularity and this was attributed to a cooperative effect of the larger fraction of abnormal grains with low switching field and, as a minor effect, a reduced degree of crystallographic texture in this sample compared to the material sintered at 980 °C, which did not show the reduced rectangularity of the demagnetisation curve. - Highlights: • He Jet milling to reduce Nd-Fe-B grain size and to enhance coercivity. • Normal and abnormal grain growth observed for low temperature sintering. • Well oriented abnormal grown grains explained by size dependent field alignment. • Poor rectangularity is caused by low nucleation field of

Preventive actions taken by workers after workers' health surveillance: a controlled trial.

Science.gov (United States)

Boschman, J S; Van der Molen, H F; Frings-Dresen, M H W; Sluiter, J K

2013-12-01

To evaluate construction workers' preventive actions and occupational physician's (OPs) recommendations after a job-specific workers' health surveillance (WHS) compared with the currently used generic WHS. After the WHS, the OPs' written recommendations were captured. At the 3-month follow-up, the workers were asked about the preventive actions they had undertaken. A generalized linear mixed model was used to compare proportions of workers. At follow-up, the proportion of workers who reported taking preventive actions was significantly higher in the intervention group (80%, 44/55) than in the control group (67%, 80 of 121), (P = 0.04). In the intervention group, the OPs provided a higher proportion of workers with written recommendations (82%, 63 of 77, vs 57%, 69 of 121; P = 0.03). The job-specific WHS aided OPs in providing workers with recommendations and workers in undertaking (job-specific) preventive actions.

Comparison of Thermodynamic Predictions and Experimental Observations on B Additions in Powder-Processed Ni-Based Superalloys Containing Elevated Concentrations of Nb

Science.gov (United States)

Antonov, Stoichko; Huo, Jiajie; Feng, Qiang; Isheim, Dieter; Seidman, David N.; Sun, Eugene; Tin, Sammy

2018-03-01

Boron additions to Ni-based superalloys are considered to be beneficial to the creep properties of the alloy, as boron has often been reported to increase grain boundary cohesion, increase ductility, and promote the formation of stable boride phases. Despite the importance, it is not well understood whether these improvements are associated with the presence of elemental boron or stable borides along the grain boundaries. In this investigation, two experimental powder-processed Ni-based superalloys containing elevated levels of Nb were found to exhibit increased solubility for B in the γ matrix when compared to similar commercial Ni-based superalloys. This resulted in an overall lower B concentration at grain boundaries that suppressed boride formation. As the predictive capability of CALPHAD database models for Ni-based superalloys have improved over the years, some discrepancies may still persist around compositionally heterogeneous features such as grain boundaries. Improved quantification of the characteristic partitioning of B as a function of the bulk alloy composition is required for understanding and predicting the stability of borides.

Physical properties of five grain dust types.

OpenAIRE

Parnell, C B; Jones, D D; Rutherford, R D; Goforth, K J

1986-01-01

Physical properties of grain dust derived from five grain types (soybean, rice, corn, wheat, and sorghum) were measured and reported. The grain dusts were obtained from dust collection systems of terminal grain handling facilities and were assumed to be representative of grain dust generated during the handling process. The physical properties reported were as follows: particle size distributions and surface area measurements using a Coulter Counter Model TAII; percent dust fractions less tha...

Efficient radiative transfer in dust grain mixtures

OpenAIRE

Wolf, S.

2002-01-01

The influence of a dust grain mixture consisting of spherical dust grains with different radii and/or chemical composition on the resulting temperature structure and spectral energy distribution of a circumstellar shell is investigated. The comparison with the results based on an approximation of dust grain parameters representing the mean optical properties of the corresponding dust grain mixture reveal that (1) the temperature dispersion of a real dust grain mixture decreases substantially ...

UO2 Grain Growth: Developing Phase Field Models for Pore Dragging, Solute Dragging and Anisotropic Grain Boundary Energies

International Nuclear Information System (INIS)

Ahmed, K.; Tonks, M.; Zhang, Y.; Biner, B.

2016-01-01

A detailed phase field model for the effect of pore drag on grain growth kinetics was implemented in MARMOT. The model takes into consideration both the curvature-driven grain boundary motion and pore migration by surface diffusion. As such, the model accounts for the interaction between pore and grain boundary kinetics, which tends to retard the grain growth process. Our 2D and 3D simulations demonstrate that the model capture all possible pore-grain boundary interactions proposed in theoretical models. For high enough surface mobility, the pores move along with the migrating boundary as a quasi-rigid-body, albeit hindering its migration rate compared to the pore-free case. For less mobile pores, the migrating boundary can separate from the pores. For the pore-controlled grain growth kinetics, the model predicts a strong dependence of the growth rate on the number of pores, pore size, and surface diffusivity in agreement with theroretical models. An evolution equation for the grain size that includes these parameters was derived and showed to agree well with numerical solution. It shows a smooth transition from boundary-controlled kinetics to pore-controlled kinetics as the surface diffusivity decreases or the number of pores or their size increases. This equation can be utilized in BISON to give accurate estimate for the grain size evolution. This will be accomplished in the near future. The effect of solute drag and anisotropy of grain boundary on grain growth will be investigated in future studies.

Elevated levels of perfluoroalkyl acids in family members of occupationally exposed workers: the importance of dust transfer.

Science.gov (United States)

Fu, Jianjie; Gao, Yan; Wang, Thanh; Liang, Yong; Zhang, Aiqian; Wang, Yawei; Jiang, Guibin

2015-03-20

The exposure pathways of perfluoroalkyl acids (PFAAs) to humans are still not clear because of the complex living environment, and few studies have simultaneously investigated the bioaccumulative behaviour of different PFAAs in humans. In this study, serum, dust, duplicate diet, and other matrices were collected around a manufacturing plant in China, and homologous series of PFAAs were analysed. PFAA levels in dust and serum of local residents in this area were considerably higher than those in non-polluted area. Although dietary intake was the major exposure pathway in the present study, dust ingestion played an important role in this case. Serum PFAAs in local residents was significantly correlated with dust PFAAs levels in their living or working microenvironment. Serum PFAAs and dust PFAAs were significantly higher in family members of occupational workers (FM) than in ordinary residents (OR) (p < 0.01). After a careful analysis of the PFAAs exposure pathway, a potential pathway in addition to direct dust ingestion was suggested: PFAAs might transferred from occupational worker's clothes to dinners via cooking processes. The bioaccumulative potential of PFHxS and PFOS were higher than other PFAAs, which suggested a substantial difference between the bioaccumulative ability of perfluorinated sulfonic acids and perfluorinated carboxylic acids.

Microstructure and grain size effects on irradiation hardening of low carbon steel for reactor tanks

International Nuclear Information System (INIS)

Milasin, N.

1964-05-01

Irradiation hardening of steel for reactor pressure vessels has been studied extensively during the past few years. A great number of experimental results concerning the behaviour of these steels in the radiation field and several review papers (1,2) have been published. Most of the papers deal with the effects of specific metallurgical factors or irradiation conditions (temperature, flux) on irradiation hardening and embrittlement. In addition, a number of experiments are performed to give evidence on the mechanism of irradiation hardening of these steels. However, this mechanism is still unknown due to the complexity of steel as a system. Among different methods used in radiation damage studies, the changes of mechanical properties have been mainly investigated. By using Hall-Petch's empirical relation, σ y =σ i +k y d -1/2 between lower yield stress, σ y , and grain size, 2d, the information about the effect of irradiation on the parameters σ i and k y is obtained. Taking as a base interpretation of σ i and k y given by Petch and his co-workers it has been concluded that radiation does not change the stress to start slip but that it increase the friction that opposes the passage of free dislocations across a slip plane. In attempting to apply Hall-Petch's relation to one unirradiated ferritic steel with a carbon content higher than 0.15% some difficulties were encountered. The results obtained indicate that the influence of grain size can not be isolated from other factors introduced by the treatments used to produce different grain sizes. This paper deals with a similar problem in the case of irradiated steel. The results obtained give the changes of the mechanical properties of steel in neutron irradiation field as a function of microstructure and grain size. In addition, the mechanical properties of irradiated steel are measured after annealing at 150 deg C and 450 deg C. On the basis of the experimental results obtained the relative microstructure and

Physics of dust grains in hot gas

International Nuclear Information System (INIS)

Draine, B.T.; Salpeter, E.E.

1979-01-01

Charging of dust grains in hot (10 4 --10 9 K) plasma is studied, including photoelectron and secondary electron emission, field emission, and transmission of electrons and ions through the grain; resulting grain potentials are (for T > or approx. = 10 5 K) considerably smaller in magnitude than found by Burke and Silk. Even so, large electrostatic stresses can cause ion field emission and rapid destruction of small grains in very hot gas. Rapid rotation can also disrupt small grains, but damping (by microwave emission) usually limits the centrifugal stress to acceptable values for plasma densities n/sub H/ -3 . Sputtering rates are estimated for grains in hot gas, based upon a semiempirical fit to experimental data. Predicted sputtering rates for possible grain constituents are similar to estimates by Barlow, but in some cases differ significantly. Useful approximation formulae are given for the drag forces acting on a grain with arbitrary Mach number

Managing for Multifunctionality in Perennial Grain Crops

Science.gov (United States)

Ryan, Matthew R; Crews, Timothy E; Culman, Steven W; DeHaan, Lee R; Hayes, Richard C; Jungers, Jacob M; Bakker, Matthew G

2018-01-01

Abstract Plant breeders are increasing yields and improving agronomic traits in several perennial grain crops, the first of which is now being incorporated into commercial food products. Integration strategies and management guidelines are needed to optimize production of these new crops, which differ substantially from both annual grain crops and perennial forages. To offset relatively low grain yields, perennial grain cropping systems should be multifunctional. Growing perennial grains for several years to regenerate soil health before rotating to annual crops and growing perennial grains on sloped land and ecologically sensitive areas to reduce soil erosion and nutrient losses are two strategies that can provide ecosystem services and support multifunctionality. Several perennial cereals can be used to produce both grain and forage, and these dual-purpose crops can be intercropped with legumes for additional benefits. Highly diverse perennial grain polycultures can further enhance ecosystem services, but increased management complexity might limit their adoption. PMID:29662249

Stress-driven grain growth

CSIR Research Space (South Africa)

Nabarro, FRN

1998-11-13

Full Text Available of length b (1+ epsilon) is parallel to sigma, embedded in a grain in which the lattice vector b (1+ epsilon) is transverse to sigma. If the embedded grain grows at the expense of its matrix, the source of the stress will do work, and therefore the presence...

Iron and zinc complexation in wild-type and ferritin-expressing wheat grain: implications for mineral transport into developing grain

DEFF Research Database (Denmark)

Neal, Andrew L; Geraki, Kalotina; Borg, Søren

2013-01-01

of modified complexation of both metals in transgenic grain overexpressing wheat ferritin. For zinc, there is a consistent doubling of the number of complexing phosphorus atoms. Although there is some EXAFS evidence for iron phytate in ferritin-expressing grain, there is also evidence of a structure lacking......We have used synchrotron-based X-ray fluorescence and absorption techniques to establish both metal distribution and complexation in mature wheat grains. In planta, extended X-ray absorption fine structure (EXAFS) spectroscopy reveals iron phytate and zinc phytate structures in aleurone cells...... of ferritin-expressing grains is quite different from that in wild-type grain. This may explain why the raised levels of minerals transported to the developing grain accumulate within the crease region of the transgenic grain....

Self-assessment of hearing status and risk of noise-induced hearing loss in workers in a rolling stock plant.

Science.gov (United States)

Pawlaczyk-Łuszczyńska, Małgorzata; Dudarewicz, Adam; Zamojska, Małgorzata; Sliwinska-Kowalska, Mariola

2012-01-01

Noise measurements and questionnaire inquiries were carried out for 124 workers of a rolling stock plant to develop a hearing conservation program. On the basis of that data, the risk of noise-induced hearing loss (NIHL) was evaluated. Additionally, the workers' hearing ability was assessed with the (modified) Amsterdam inventory for auditory disability and handicap, (m)AIADH. The workers had been exposed to noise at A-weighted daily noise exposure levels of 74-110 dB for 1-40 years. Almost one third of the workers complained of hearing impairment and the (m)AIADH results showed some hearing difficulties in over half of them. The estimated risk of hearing loss over 25 dB in the frequency range of 3-6 kHz was 41-50% when the standard method of predicting NIHL specified in Standard No. ISO 1999:1990 was used. This risk increased to 50-67% when noise impulsiveness, coexposure to organic solvents, elevated blood pressure and smoking were included in calculations.

The Relevance of Grain Dissection for Grain Size Reduction in Polar Ice: Insights from Numerical Models and Ice Core Microstructure Analysis

Directory of Open Access Journals (Sweden)

Florian Steinbach

2017-09-01

Full Text Available The flow of ice depends on the properties of the aggregate of individual ice crystals, such as grain size or lattice orientation distributions. Therefore, an understanding of the processes controlling ice micro-dynamics is needed to ultimately develop a physically based macroscopic ice flow law. We investigated the relevance of the process of grain dissection as a grain-size-modifying process in natural ice. For that purpose, we performed numerical multi-process microstructure modeling and analyzed microstructure and crystallographic orientation maps from natural deep ice-core samples from the North Greenland Eemian Ice Drilling (NEEM project. Full crystallographic orientations measured by electron backscatter diffraction (EBSD have been used together with c-axis orientations using an optical technique (Fabric Analyser. Grain dissection is a feature of strain-induced grain boundary migration. During grain dissection, grain boundaries bulge into a neighboring grain in an area of high dislocation energy and merge with the opposite grain boundary. This splits the high dislocation-energy grain into two parts, effectively decreasing the local grain size. Currently, grain size reduction in ice is thought to be achieved by either the progressive transformation from dislocation walls into new high-angle grain boundaries, called subgrain rotation or polygonisation, or bulging nucleation that is assisted by subgrain rotation. Both our time-resolved numerical modeling and NEEM ice core samples show that grain dissection is a common mechanism during ice deformation and can provide an efficient process to reduce grain sizes and counter-act dynamic grain-growth in addition to polygonisation or bulging nucleation. Thus, our results show that solely strain-induced boundary migration, in absence of subgrain rotation, can reduce grain sizes in polar ice, in particular if strain energy gradients are high. We describe the microstructural characteristics that can be

The relevance of grain dissection for grain size reduction in polar ice: insights from numerical models and ice core microstructure analysis

Science.gov (United States)

Steinbach, Florian; Kuiper, Ernst-Jan N.; Eichler, Jan; Bons, Paul D.; Drury, Martyn R.; Griera, Albert; Pennock, Gill M.; Weikusat, Ilka

2017-09-01

The flow of ice depends on the properties of the aggregate of individual ice crystals, such as grain size or lattice orientation distributions. Therefore, an understanding of the processes controlling ice micro-dynamics is needed to ultimately develop a physically based macroscopic ice flow law. We investigated the relevance of the process of grain dissection as a grain-size-modifying process in natural ice. For that purpose, we performed numerical multi-process microstructure modelling and analysed microstructure and crystallographic orientation maps from natural deep ice-core samples from the North Greenland Eemian Ice Drilling (NEEM) project. Full crystallographic orientations measured by electron backscatter diffraction (EBSD) have been used together with c-axis orientations using an optical technique (Fabric Analyser). Grain dissection is a feature of strain-induced grain boundary migration. During grain dissection, grain boundaries bulge into a neighbouring grain in an area of high dislocation energy and merge with the opposite grain boundary. This splits the high dislocation-energy grain into two parts, effectively decreasing the local grain size. Currently, grain size reduction in ice is thought to be achieved by either the progressive transformation from dislocation walls into new high-angle grain boundaries, called subgrain rotation or polygonisation, or bulging nucleation that is assisted by subgrain rotation. Both our time-resolved numerical modelling and NEEM ice core samples show that grain dissection is a common mechanism during ice deformation and can provide an efficient process to reduce grain sizes and counter-act dynamic grain-growth in addition to polygonisation or bulging nucleation. Thus, our results show that solely strain-induced boundary migration, in absence of subgrain rotation, can reduce grain sizes in polar ice, in particular if strain energy gradients are high. We describe the microstructural characteristics that can be used to

Risk of occupational exposure to ionizing radiation among medical workers in Canada

International Nuclear Information System (INIS)

Zielinski, Jan M.; Band, Pierre R.; Garner, Michael J.; Krewski, Daniel; Shilnikova, Natalia S.; Jiang, Huixia; Ashmore, Patrick J.; Sont, Willem N.; Fair, Martha E.; Letourneau, Ernest G.; Semenciw, Robert

2010-01-01

Medical workers are exposed to chronic low dose ionizing radiation from a variety of sources. Potential cancer risks associated with ionizing radiation exposures have been derived from cohorts experiencing acute high intensity exposure, most notably the Japanese atomic bomb survivors. Since such extrapolations are subject to uncertainty, direct information on the risk associated with chronic low dose occupational exposure to ionizing radiation is needed. We examined possible associations with cancer incidence and mortality in a cohort of medical workers ascertained by the National Dose Registry of Canada (NDR). Data from the NDR were used to assess the exposure to ionizing radiation incurred between 1951 to 1987 inclusive in a cohort of 67,562 subjects classified as medical workers. Standardized mortality (SMRs) and incidence (SIRs) ratios were ascertained by linking NDR data with the data maintained by Statistics Canada in the Canadian Mortality and in the Canadian Cancer Incidence Databases respectively. Dosimetry information was obtained from the National Dosimetry Services of the Radiation Protection Bureau of Health Canada. There were 23,580 male and 43,982 female medical workers in the cohort. During the follow-up period, 1309 incident cases of cancer (509 in males, 800 in females) and 1,325 deaths (823 in males, 502 in females) were observed. Mortality from cancer and non-cancer causes was generally below expected compared to the Canadian population. Thyroid cancer incidence was significantly elevated in both males and females, with a combined SIR of 1.74 and 90% confidence interval (90% CI: 1.40-2.10). Our result of an increased risk of thyroid cancer among medical workers occupationally exposed to ionizing radiation confirms previous reports. Over the last 50 years, radiation protection measures have been effective in reducing occupational exposures of medical workers to ionizing radiation to current very low levels. (author)

Radiological Worker Training: Radiological Worker 2 study guides

International Nuclear Information System (INIS)

1992-10-01

Upon completion of this training course, the participant will have the knowledge to work safely in areas controlled for radiological purposes using proper radiological practices. Radiological Worker H Training, for the worker whose job assignment involves entry into Radiological Buffer Areas and all types of Radiation Contamination and Airborne Radioactivity Areas. This course is designed to prepare the worker to work safely in and around radiological areas and present methods to use to ensure individual radiation exposure is maintained As Low As Reasonably Achievable

Bioactive compounds in whole grain wheat

NARCIS (Netherlands)

Mateo Anson, N.

2010-01-01

Bread can be healthier! Consuming whole-grain foods can prevent cardiovascular diseases, type-2 diabetes and metabolic syndrome. This is due to bioactive compounds in whole grain, such as antioxidants and anti-inflammatory compounds. We found that the different fractions of a wheat grain vary much

Joining of CBN abrasive grains to medium carbon steel with Ag-Cu/Ti powder mixture as active brazing alloy

International Nuclear Information System (INIS)

Ding, W.F.; Xu, J.H.; Shen, M.; Su, H.H.; Fu, Y.C.; Xiao, B.

2006-01-01

In order to develop new generation brazed CBN grinding wheels, the joining experiments of CBN abrasive grains and medium carbon steel using the powder mixture of Ag-Cu alloy and pure Ti as active brazing alloy are carried out at elevated temperature under high vacuum condition. The relevant characteristics of the special powder mixture, the microstructure of the interfacial region, which are both the key factors for determining the joining behavior among the CBN grains, the filler layer and the steel substrate, are investigated extensively by means of differential thermal analysis (DTA), scanning electron microscope (SEM) and energy dispersion spectrometer (EDS), as well X-ray diffraction (XRD) analysis. The results show that, similar to Ag-Cu-Ti filler alloy, Ag-Cu/Ti powder mixture exhibits good soakage capability to CBN grains during brazing. Moreover, Ti in the powder mixture concentrates preferentially on the surface of the grains to form a layer of needlelike Ti-N and Ti-B compounds by chemical metallurgic interaction between Ti, N and B at high temperature. Additionally, based on the experimental results, the brazing and joining mechanism is deeply discussed in a view of thermodynamic criterion and phase diagram of Ti-B-N ternary system

Grain processes in massive star formation

International Nuclear Information System (INIS)

Wolfire, M.G.; Cassinelli, J.P.

1986-01-01

Observational evidence suggests that stars greater than 100 M(solar) exist in the Galaxy and Large Magellanic Cloud (LMC), however classical star formation theory predicts stellar mass limits of only approx. 60 M(solar). A protostellar accretion flow consists of inflowing gas and dust. Grains are destroyed as they are near the central protostar creating a dust shell or cocoon. Radiation pressure acting on the grain can halt the inflow of material thereby limiting the amount of mass accumulated by the protostar. We first consider rather general constraints on the initial grain to gas ratio and mass accretion rates that permit inflow. We further constrain these results by constructing a numerical model. Radiative deceleration of grains and grain destruction processes are explicitly accounted for in an iterative solution of the radiation-hydrodynamic equations. Findings seem to suggest that star formation by spherical accretion requires rather extreme preconditioning of the grain and gas environment

Prevalence and predictors of alanine aminotransferase elevation among normal weight, overweight and obese youth in Mexico.

Science.gov (United States)

Purcell, Maura; Flores, Yvonne N; Zhang, Zuo-Feng; Denova-Gutiérrez, Edgar; Salmeron, Jorge

2013-09-01

This study aimed to determine the prevalence of and risk factors associated with elevated alanine aminotransferase (ALT) levels among a sample of normal weight, overweight and obese youth from two urban populations in Central Mexico. Baseline data from 1262 youth aged 8-19 years who participated in the Mexican Health Worker Cohort Study from March 2004 to April 2006 were reviewed, including 680 girls and 582 boys, with a total of 83 participants with elevated ALT level (>40 U/L). Information was obtained from self-administered questionnaires, anthropometric results and clinical measurements. Associations of interest were examined using multivariate logistic regression models. A total of 3.8% of girls and 9.8% of boys had elevated ALT levels. Elevated ALT was observed in 28.9% of the obese and 14.2% of the overweight participants. Metabolic syndrome (MS) occurred in 6.1% of the study population and those with MS had a high percentage of elevated ALT (14.5% of girls and 40.0% of boys, respectively). Abdominal obesity and insulin resistance were also associated with a greater risk of elevated ALT. Obesity and certain metabolic risk factors are important predictors for elevated ALT. Screening for ALT levels in obese youth could help to identify those at risk and reduce the possibility of future liver diseases. © 2013 Wiley Publishing Asia Pty Ltd and Chinese Medical Association Shanghai Branch, Chinese Society of Gastroenterology, Renji Hospital Affiliated to Shanghai Jiaotong University School of Medicine.

WIDE AND THICK GRAIN 1, which encodes an otubain-like protease with deubiquitination activity, influences grain size and shape in rice.

Science.gov (United States)

Huang, Ke; Wang, Dekai; Duan, Penggen; Zhang, Baolan; Xu, Ran; Li, Na; Li, Yunhai

2017-09-01

Grain size and shape are two crucial traits that influence grain yield and grain appearance in rice. Although several factors that affect grain size have been described in rice, the molecular mechanisms underlying the determination of grain size and shape are still elusive. In this study we report that WIDE AND THICK GRAIN 1 (WTG1) functions as an important factor determining grain size and shape in rice. The wtg1-1 mutant exhibits wide, thick, short and heavy grains and also shows an increased number of grains per panicle. WTG1 determines grain size and shape mainly by influencing cell expansion. WTG1 encodes an otubain-like protease, which shares similarity with human OTUB1. Biochemical analyses indicate that WTG1 is a functional deubiquitinating enzyme, and the mutant protein (wtg1-1) loses this deubiquitinating activity. WTG1 is expressed in developing grains and panicles, and the GFP-WTG1 fusion protein is present in the nucleus and cytoplasm. Overexpression of WTG1 results in narrow, thin, long grains due to narrow and long cells, further supporting the role of WTG1 in determining grain size and shape. Thus, our findings identify the otubain-like protease WTG1 to be an important factor that determines grain size and shape, suggesting that WTG1 has the potential to improve grain size and shape in rice. © 2017 The Authors The Plant Journal © 2017 John Wiley & Sons Ltd.

Sustainable production of grain crops for biofuels

Science.gov (United States)

Grain crops of the Gramineae are grown for their edible, starchy seeds. Their grain is used directly for human food, livestock feed, and as raw material for many industries, including biofuels. Using grain crops for non-food uses affects the amount of food available to the world. Grain-based biofuel...

Effects of grain-producing cover crops on rice grain yield in Cabo Delgado, Mozambique

Directory of Open Access Journals (Sweden)

Adriano Stephan Nascente

Full Text Available ABSTRACT Besides providing benefits to the environment such as soil protection, release of nutrients, soil moisture maintenance, and weed control, cover crops can increase food production for grain production. The aim of this study was to evaluate the production of biomass and grain cover crops (and its respective effects on soil chemical and physical attributes, yield components, and grain yield of rice in Mozambique. The study was conducted in two sites located in the province of Cabo Delgado, in Mozambique. The experimental design was a randomized block in a 2 × 6 factorial, with four repetitions. Treatments were carried out in two locations (Cuaia and Nambaua with six cover crops: Millet (Pennisetum glaucum L.; namarra bean (Lablab purpureus (L. Sweet, velvet beans (Mucuna pruriens L., oloco beans (Vigna radiata (L. R. Wilczek, cowpea (Vigna unguiculata L., and fallow. Cover crops provided similar changes in chemical and physical properties of the soil. Lablab purpureus, Vigna unguiculata, and Mucuna pruriens produced the highest dry matter biomass. Vigna unguiculada produced the highest amount of grains. Rice grain yields were similar under all cover crops and higher in Cuaia than Nambaua.

Engineering high α-amylase levels in wheat grain lowers Falling Number but improves baking properties.

Science.gov (United States)

Ral, Jean-Philippe; Whan, Alex; Larroque, Oscar; Leyne, Emmett; Pritchard, Jeni; Dielen, Anne-Sophie; Howitt, Crispin A; Morell, Matthew K; Newberry, Marcus

2016-01-01

Late maturity α-amylase (LMA) and preharvest sprouting (PHS) are genetic defects in wheat. They are both characterized by the expression of specific isoforms of α-amylase in particular genotypes in the grain prior to harvest. The enhanced expression of α-amylase in both LMA and PHS results in a reduction in Falling Number (FN), a test of gel viscosity, and subsequent downgrading of the grain, along with a reduced price for growers. The FN test is unable to distinguish between LMA and PHS; thus, both defects are treated similarly when grain is traded. However, in PHS-affected grains, proteases and other degradative process are activated, and this has been shown to have a negative impact on end product quality. No studies have been conducted to determine whether LMA is detrimental to end product quality. This work demonstrated that wheat in which an isoform α-amylase (TaAmy3) was overexpressed in the endosperm of developing grain to levels of up to 100-fold higher than the wild-type resulted in low FN similar to those seen in LMA- or PHS-affected grains. This increase had no detrimental effect on starch structure, flour composition and enhanced baking quality, in small-scale 10-g baking tests. In these small-scale tests, overexpression of TaAmy3 led to increased loaf volume and Maillard-related browning to levels higher than those in control flours when baking improver was added. These findings raise questions as to the validity of the assumption that (i) LMA is detrimental to end product quality and (ii) a low FN is always indicative of a reduction in quality. This work suggests the need for a better understanding of the impact of elevated expression of specific α-amylase on end product quality. © 2015 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

The influence of grain size, grain color, and suspended-sediment concentration on light attenuation: why fine-grained terrestrial sediment is bad for coral reef ecosystems

Science.gov (United States)

Storlazzi, Curt; Norris, Benjamin; Rosenberger, Kurt

2015-01-01

Sediment has been shown to be a major stressor to coral reefs globally. Although many researchers have tested the impact of sedimentation on coral reef ecosystems in both the laboratory and the field and some have measured the impact of suspended sediment on the photosynthetic response of corals, there has yet to be a detailed investigation on how properties of the sediment itself can affect light availability for photosynthesis. We show that finer-grained and darker-colored sediment at higher suspended-sediment concentrations attenuates photosynthetically active radiation (PAR) significantly more than coarser, lighter-colored sediment at lower concentrations and provide PAR attenuation coefficients for various grain sizes, colors, and suspended-sediment concentrations that are needed for biophysical modeling. Because finer-grained sediment particles settle more slowly and are more susceptible to resuspension, they remain in the water column longer, thus causing greater net impact by reducing light essential for photosynthesis over a greater duration. This indicates that coral reef monitoring studies investigating sediment impacts should concentrate on measuring fine-grained lateritic and volcanic soils, as opposed to coarser-grained siliceous and carbonate sediment. Similarly, coastal restoration efforts and engineering solutions addressing long-term coral reef ecosystem health should focus on preferentially retaining those fine-grained soils rather than coarse silt and sand particles.

Short and long term effects of a lifestyle intervention for construction workers at risk for cardiovascular disease: A randomized controlled trial

NARCIS (Netherlands)

Groeneveld, I.F.; Proper, K.I.; Beek, A.J. van der; Hildebrandt, V.H.; Mechelen, W. van

2011-01-01

Background: The prevalence of overweight and elevated cardiovascular disease (CVD) risk among workers in the construction industry is relatively high. Improving lifestyle lowers CVD risk and may have work-related benefits. The purpose of the study was to evaluate the effects on physical activity

Whole grain gluten-free egg-free pasta

Science.gov (United States)

The USDA food guide recommends that at least ½ of all the grains eaten should be whole grains. The FDA allows food Health Claim labels for food containing 51% whole grains and 11 g of dietary fiber. This is the only report demonstrating innovative whole grain gluten free, egg free (no chemicals adde...

Influence of grain structure on the deformation mechanism in martensitic shear reversion-induced Fe-16Cr-10Ni model austenitic alloy with low interstitial content: Coarse-grained versus nano-grained/ultrafine-grained structure

Energy Technology Data Exchange (ETDEWEB)

Challa, V.S.A. [Laboratory for Excellence in Advanced Steel Research, Department of Metallurgical, Materials Engineering, and Biomedical Engineering, University of Texas at El Paso, El Paso, TX 79968 (United States); Misra, R.D.K., E-mail: dmisra2@utep.edu [Laboratory for Excellence in Advanced Steel Research, Department of Metallurgical, Materials Engineering, and Biomedical Engineering, University of Texas at El Paso, El Paso, TX 79968 (United States); Somani, M.C. [Center for Advanced Steels Research, The University of Oulu, P.O. Box 4200, 90014 Oulu (Finland); Wang, Z.D. [State Key Laboratory for Rolling and Automation, Northeastern University, 3-11 Wenhua Road, Shenyang 110819 (China)

2016-04-20

Nanograined/ultrafine-grained (NG/UFG) materials characterized by high strength-high ductility combination are excellent vehicles to obtain an unambiguous understanding of deformation mechanisms vis-à-vis their coarse-grained counterparts. In this context, the innovative concept of phase reversion-induced NG/UFG structure enabled achieving high strength besides comparable ductility, for instance, in metastable austenitic stainless steels. In the phase reversion process, severe deformation of austenite at room temperature (typically ~60–80%) transforms face-centered cubic austenite (γ) to body centered cubic martensite (α′). Upon annealing, martensite reverts to austenite leading to extensive grain refinement. The objective of the present study to fundamentally understand the deformation mechanisms in NG/UFG structure in relation to that of the coarse-grained (CG) structure was accomplished by combining depth-sensing nanoscale experiments on an Fe-16Cr-10Ni model austenitic alloy conducted at different strain rates, followed by the study of structural evolution in the deformed zone using transmission electron microscopy (TEM). In the high strength NG/UFG steel (YS~585 MPa), stacking faults and nanotwins contributed to the enhanced ductility (El~35%), while in the case of low strength (YS~260 MPa) coarse-grained (CG) counterpart, ductility was also high (El~40%), but chiefly due to strain-induced martensite, which points to a clear case of grain size effect (and the corresponding level of strength). The distinct change in the deformation mechanism from stacking faults and twinning-induced plasticity (TWIP) in the NG structure to transformation-induced plasticity (TRIP) in the CG structure is elucidated in terms of austenite stability-strain energy relationship. The insights on the relationship between grain structure (and strength) and deformation mechanisms are envisaged to be important in providing a new direction for the futuristic design of high strength

Deformation inhomogeneity in large-grained AA5754 sheets

International Nuclear Information System (INIS)

Zhu Guozhen; Hu Xiaohua; Kang Jidong; Mishra, Raja K.; Wilkinson, David S.

2011-01-01

Research highlights: → Microstructure and strain relationship at individual grain level was studied. → 'Hot spots' nucleate early and most keep growing throughout deformation stages. → 'Hot spots' are correlated with 'soft' grains and soft-evolution grains. → Grains with high Schmid factors tend to be 'soft' grains. → Grains with the direction close to tensile axis tend to become softer. - Abstract: Models for deformation and strain localization in polycrystals that incorporate microstructural features including particles are computationally intensive due to the large variation in scale in going from particles to grains to a specimen. As a result such models are generally 2-D in nature. This is an issue for experimental validation. We have therefore studied deformation heterogeneities and strain localization behavior of coarse-grained alloys with only two grains across the sample thickness, therefore mimicking 2-D behavior. Aluminum alloy sheets (AA5754) have been investigated by a number of surface techniques, including digital image correlation, slip trace analysis and electron backscattered diffraction, at the individual grain level. Local strain concentration zones appear from the very beginning of deformation, which then maintain sustained growth and lead, in one of these regions, to localization and final fracture. These 'hot spots' occur in areas with locally soft grains (i.e. grains with or close to the tensile direction) and soft-evolution orientations (i.e. grains with close to the tensile direction). These grains can be correlated with Taylor and/or Schmid factors.

Tracing magnetic fields with aligned grains

International Nuclear Information System (INIS)

Lazarian, A.

2007-01-01

Magnetic fields play a crucial role in various astrophysical processes, including star formation, accretion of matter, transport processes (e.g., transport of heat), and cosmic rays. One of the easiest ways to determine the magnetic field direction is via polarization of radiation resulting from extinction or/and emission by aligned dust grains. Reliability of interpretation of the polarization maps in terms of magnetic fields depends on how well we understand the grain-alignment theory. Explaining what makes grains aligned has been one of the big issues of the modern astronomy. Numerous exciting physical effects have been discovered in the course of research undertaken in this field. As both the theory and observations matured, it became clear that the grain-alignment phenomenon is inherent not only in diffuse interstellar medium or molecular clouds but also is a generic property of the dust in circumstellar regions, interplanetary space and cometary comae. Currently the grain-alignment theory is a predictive one, and its results nicely match observations. Among its predictions is a subtle phenomenon of radiative torques. This phenomenon, after having stayed in oblivion for many years after its discovery, is currently viewed as the most powerful means of alignment. In this article, I shall review the basic physical processes involved in grain alignment, and the currently known mechanisms of alignment. I shall also discuss possible niches for different alignment mechanisms. I shall dwell on the importance of the concept of grain helicity for understanding of many properties of grain alignment, and shall demonstrate that rather arbitrarily shaped grains exhibit helicity when they interact with gaseous and radiative flows

Grain-size distributions and grain boundaries of chalcopyrite-type thin films

International Nuclear Information System (INIS)

Abou-Ras, D.; Schorr, S.; Schock, H.W.

2007-01-01

CuInSe 2 , CuGaSe 2 , Cu(In,Ga)Se 2 and CuInS 2 thin-film solar absorbers in completed solar cells were studied in cross section by means of electronbackscatter diffraction. From the data acquired, grain-size distributions were extracted, and also the most frequent grain boundaries were determined. The grain-size distributions of all chalcopyrite-type thin films studied can be described well by lognormal distribution functions. The most frequent grainboundary types in these thin films are 60 - left angle 221 right angle tet and 71 - left angle 110 right angle tet (near) Σ3 twin boundaries. These results can be related directly to the importance of {112} tet planes during the topotactical growth of chalcopyrite-type thin films. Based on energetic considerations, it is assumed that the most frequent twin boundaries exhibit a 180 - left angle 221 right angle tet constellation. (orig.)

Grain Unloading of Arsenic Species in Rice

Energy Technology Data Exchange (ETDEWEB)

Carey, Anne-Marie; Scheckel, Kirk G.; Lombi, Enzo; Newville, Matt; Choi, Yongseong; Norton, Gareth J.; Charnock, John M.; Feldmann, Joerg; Price, Adam H.; Meharg, Andrew A. (EPA); (U. South Australia); (Manchester); (Aberdeen); (UC)

2010-01-11

Rice (Oryza sativa) is the staple food for over half the world's population yet may represent a significant dietary source of inorganic arsenic (As), a nonthreshold, class 1 human carcinogen. Rice grain As is dominated by the inorganic species, and the organic species dimethylarsinic acid (DMA). To investigate how As species are unloaded into grain rice, panicles were excised during grain filling and hydroponically pulsed with arsenite, arsenate, glutathione-complexed As, or DMA. Total As concentrations in flag leaf, grain, and husk, were quantified by inductively coupled plasma mass spectroscopy and As speciation in the fresh grain was determined by x-ray absorption near-edge spectroscopy. The roles of phloem and xylem transport were investigated by applying a {+-} stem-girdling treatment to a second set of panicles, limiting phloem transport to the grain in panicles pulsed with arsenite or DMA. The results demonstrate that DMA is translocated to the rice grain with over an order magnitude greater efficiency than inorganic species and is more mobile than arsenite in both the phloem and the xylem. Phloem transport accounted for 90% of arsenite, and 55% of DMA, transport to the grain. Synchrotron x-ray fluorescence mapping and fluorescence microtomography revealed marked differences in the pattern of As unloading into the grain between DMA and arsenite-challenged grain. Arsenite was retained in the ovular vascular trace and DMA dispersed throughout the external grain parts and into the endosperm. This study also demonstrates that DMA speciation is altered in planta, potentially through complexation with thiols.

Grain boundary corrosion of copper canister material

International Nuclear Information System (INIS)

Fennell, P.A.H.; Graham, A.J.; Smart, N.R.; Sofield, C.J.

2001-03-01

The proposed design for a final repository for spent fuel and other long-lived residues in Sweden is based on the multi-barrier principle. The waste will be encapsulated in sealed cylindrical canisters, which will then be placed in granite bedrock and surrounded by compacted bentonite clay. The canister design is based on a thick cast inner container fitted inside a corrosion-resistant copper canister. During fabrication of the outer copper canisters there will be some unavoidable grain growth in the welded areas. As grains grow they will tend to concentrate impurities within the copper at the new grain boundaries. The work described in this report was undertaken to determine whether there is any possibility of enhanced corrosion at grain boundaries within the copper canister. The potential for grain boundary corrosion was investigated by exposing copper specimens, which had undergone different heat treatments and hence had different grain sizes, to aerated artificial bentonite-equilibrated groundwater with two concentrations of chloride, for increasing periods of time. The degree of grain boundary corrosion was determined by atomic force microscopy (AFM) and optical microscopy. AFM showed no increase in grain boundary 'ditching' for low chloride groundwater. In high chloride groundwater the surface was covered uniformly with a fine-grained oxide. No increases in oxide thickness were observed. No significant grain boundary attack was observed using optical microscopy either. The work suggests that in aerated artificial groundwaters containing chloride ions, grain boundary corrosion of copper is unlikely to adversely affect SKB's copper canisters

Lung cancer risk among workers in the construction industry: results from two case-control studies in Montreal.

Science.gov (United States)

Lacourt, Aude; Pintos, Javier; Lavoué, Jérôme; Richardson, Lesley; Siemiatycki, Jack

2015-09-22

Given the large number of workers in the construction industry, it is important to derive accurate and valid estimates of cancer risk, and in particular lung cancer risk. In most previous studies, risks among construction workers were compared with general populations including blue and white collar workers. The main objectives of this study were to assess whether construction workers experience excess lung cancer risk, and whether exposure to selected construction industry exposures carries excess risks. We wished to address these objectives within the sub-population of blue collar workers. Two case-control studies were conducted in Montreal. Combined, they included 1593 lung cancer cases and 1427 controls, of whom 1304 cases and 1081 controls had been blue collar workers. Detailed lifetime job histories were obtained and translated by experts into histories of exposure to chemical agents. The two key analyses were to estimate odds ratio (OR) estimates of lung cancer risk: a) for all blue-collar construction workers compared with other blue-collar workers, and b) for construction workers exposed to each of 20 exposure agents found in the construction industry compared with construction workers unexposed to those agents. All analyses were conducted using unconditional logistic regression adjusted for socio-demographic factors and smoking history. The OR for all construction workers combined was 1.11 (95 % CI: 0.90-1.38), based on 381 blue collar construction workers. Analyses of specific exposures were hampered by small numbers and imprecise estimates. While none of 20 occupational agents examined was significantly associated with lung cancer, the following agents manifested non-significantly elevated ORs: asbestos, silica, Portland cement, soil dust, calcium oxide and calcium sulfate. Compared with other blue collar workers, there was only a slight increased risk of lung cancer for subjects who ever held an occupation in the construction industry. The analyses of

7 CFR 810.801 - Definition of mixed grain.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Definition of mixed grain. 810.801 Section 810.801 Agriculture Regulations of the Department of Agriculture (Continued) GRAIN INSPECTION, PACKERS AND STOCKYARD... GRAIN United States Standards for Mixed Grain Terms Defined § 810.801 Definition of mixed grain. Any...

Worker participation - the Netherlands

OpenAIRE

Kwantes, J.H.

2014-01-01

Worker participation relates to the involvement of workers in the management decision-making processes. In this article attention is focused on worker participation related to occupational safety and health in the Netherlands. Worker participation can refer either to direct or indirect participation by the worker. Indirect participation involves employee representation, while direct participation relates to individual involvement in management’s decision-making processes. In the Framework Dir...

Nanoscale abnormal grain growth in (001) epitaxial ceria

International Nuclear Information System (INIS)

Solovyov, Vyacheslav F.; Develos-Bagarinao, Katherine; Nykypanchuk, Dmytro

2009-01-01

X-ray reciprocal-space mapping and atomic force microscopy (AFM) are used to study kinetics and mechanisms of lateral grain growth in epitaxial (001) ceria (CeO 2 ) deposited by pulsed laser deposition on (001) yttria-stabilized zirconia (YSZ) and (12 lowbar 10) (r-cut) sapphire. Rate and character of the grain growth during postannealing at 1050 deg. C are found to be strongly dependent on the type of the epitaxial substrate. Films deposited on YSZ exhibit signatures of normal grain growth, which stagnated after the lateral grain size reaches 40 nm, consistent with the grain-boundary pinning by the thermal grooving. In contrast, when r-cut sapphire substrate was used, abnormal (secondary) grain growth is observed. A small population of grains grow to well over 100 nm consuming smaller, 100 nm large (001) terminations and rendering the sample single-crystalline quality. The grain growth is accompanied by reduction in lateral rms strain, resulting in a universal grain size--rms strain dependence. Analysis of the AFM and x-ray diffraction data leads to the conclusion that bimodal initial grain population consisting of grains with very different sizes is responsible for initiation of the abnormal growth in (001) CeO 2 films on r-cut sapphire. Due to different surface chemistry, when a YSZ substrate is used, the initial grain distribution is monomodal, therefore only normal growth is active. We demonstrate that a 2.2 deg. miscut of the sapphire substrate eliminates the large-grain population, thus suppressing abnormal grain growth. It is concluded that utilization of abnormal grain growth is a promising way for synthesis of large (001) ceria terminations.

Physical properties of five grain dust types.