WorldWideScience

Sample records for grade malanjkhand chalcopyrite

  1. Optimization of staged bioleaching of low-grade chalcopyrite ore in the presence and absence of chloride in the irrigating lixiviant: ANFIS simulation.

    Science.gov (United States)

    Vakylabad, Ali Behrad; Schaffie, Mahin; Naseri, Ali; Ranjbar, Mohammad; Manafi, Zahra

    2016-07-01

    In this investigation, copper was bioleached from a low-grade chalcopyrite ore using a chloride-containing lixiviant. In this regard, firstly, the composition of the bacterial culture media was designed to control the cost in commercial application. The bacterial culture used in this process was acclimated to the presence of chloride in the lixiviant. Practically speaking, the modified culture helped the bio-heap-leaching system operate in the chloridic media. Compared to the copper recovery from the low-grade chalcopyrite by bioleaching in the absence of chloride, bioleaching in the presence of chloride resulted in improved copper recovery. The composition of the lixiviant used in this study was a modification with respect to the basal salts in 9 K medium to optimize the leaching process. When leaching the ore in columns, 76.81 % Cu (based on solid residues of bioleaching operation) was recovered by staged leaching with lixiviant containing 34.22 mM NaCl. The quantitative findings were supported by SEM/EDS observations, X-ray elemental mapping, and mineralogical analysis of the ore before and after leaching. Finally, Adaptive neuro-fuzzy inference system (ANFIS) was used to simulate the operational parameters affecting the bioleaching operation in chloride-sulfate system.

  2. Metagenomic exploration of microbial community in mine tailings of Malanjkhand copper project, India

    Directory of Open Access Journals (Sweden)

    Abhishek Gupta

    2017-06-01

    Full Text Available Mine tailings from copper mines are considered as one of the sources of highly hazardous acid mine drainage (AMD due to bio-oxidation of its sulfidic constituents. This study was designed to understand microbial community composition and potential for acid generation using samples from mine tailings of Malanjkhand copper project (MCP, India through 16S rRNA gene based amplicon sequencing approach (targeting V4 region. Three tailings samples (T1, T2 and T3 with varied physiochemical properties selected for the study revealed distinct microbial assemblages. Sample (T3 with most extreme nature (pH 3.0 exhibited abundance of Proteobacteria, Fimicutes, Actinobacteria and/or Nitrospirae. Metagenomic sequences are available under the BioProject ID PRJNA361456.

  3. Recovery of copper and precious metals from chalcopyrite low grade ores - choice between flotation or microorganisms leaching

    OpenAIRE

    Krstev, Boris; Golomeov, Blagoj; Konzulov, Gerasim; Gocev, Zivko

    1998-01-01

    The conventional flotation technologies cannot provide fair results when to applied to very low grade ores or to "refractory" ores. This class include intimate and nonuniform mineral associations, with partialy oxidized minerals and high secondary mineral content and also high soluble salt content, pre-activated minerals because of the excessive permeability of the deposit and of the intense circulation of waters with heavy metal ions etc. Bacterial oxidation as a means to the recovery of met...

  4. Ternary chalcopyrite semiconductors

    CERN Document Server

    Shay, J L; Pamplin, B R

    2013-01-01

    Ternary Chalcopyrite Semiconductors: Growth, Electronic Properties, and Applications covers the developments of work in the I-III-VI2 and II-IV-V2 ternary chalcopyrite compounds. This book is composed of eight chapters that focus on the crystal growth, characterization, and applications of these compounds to optical communications systems. After briefly dealing with the status of ternary chalcopyrite compounds, this book goes on describing the crystal growth of II-IV-V2 and I-III-VI2 single crystals. Chapters 3 and 4 examine the energy band structure of these semiconductor compounds, illustrat

  5. Wide-Gap Chalcopyrites

    CERN Document Server

    Siebentritt, Susanne

    2006-01-01

    Chalcopyrites, in particular those with a wide band gap, are fascinating materials in terms of their technological potential in the next generation of thin-film solar cells and in terms of their basic material properties. They exhibit uniquely low defect formation energies, leading to unusual doping and phase behavior and to extremely benign grain boundaries. This book collects articles on a number of those basic material properties of wide-gap chalcopyrites, comparing them to their low-gap cousins. They explore the doping of the materials, the electronic structure and the transport through interfaces and grain boundaries, the formation of the electric field in a solar cell, the mechanisms and suppression of recombination, the role of inhomogeneities, and the technological role of wide-gap chalcopyrites.

  6. The dissolution of chalcopyrite in chloride media

    International Nuclear Information System (INIS)

    Ibanez, T.; Velasquez, L.

    2013-01-01

    The aim of this investigation is to determinate the effects of parameters and additives on the kinetics of dissolution of chalcopyrite on moderated conditions by means of dissolutions test with chalcopyrite concentrate and pure chalcopyrite in shake flasks and instrumented stirred reactors. A study of the dissolution of chalcopyrite in chloride solutions has demonstrated that the rate of dissolution of chalcopyrite is strongly dependent on the potential of the solution within a range of 540 to 630 mV (versus SHE). Leaching at pH around 2.5 results in increased rates of copper dissolution suggesting the possibility to keep the solution potential within the range. Both pyrite and silver ions enhance the dissolution of chalcopyrite and this effect increases when both species are present. The MnO 2 has a negative effect on the dissolution increasing the solution potential to values where the rate decreases considerably. (Author)

  7. Bioleaching of two different types of chalcopyrite by Acidithiobacillus ferrooxidans

    Science.gov (United States)

    Dong, Ying-bo; Lin, Hai; Fu, Kai-bin; Xu, Xiao-fang; Zhou, Shan-shan

    2013-02-01

    Two different types of chalcopyrite (pyritic chalcopyrite and porphyry chalcopyrite) were bioleached with Acidithiobacillus ferrooxidans ATF6. The bioleaching of the pyritic chalcopyrite and porphyry chalcopyrite is quite different. The copper extraction reaches 46.96% for the pyritic chalcopyrite after 48-d leaching, but it is only 14.50% for the porphyry chalcopyrite. Proper amounts of initial ferrous ions can improve the efficiency of copper extraction for the two different types of chalcopyrite. The optimum dosage of ferrous ions for the pyritic chalcopyrite and porphyry chalcopyrite is different. The adsorption of ATF6 on the pyritic chalcopyrite and porphyry chalcopyrite was also studied in this paper. It is found that ATF6 is selectively adsorbed by the two different types of chalcopyrite; the higher adsorption onto the pyritic chalcopyrite than the porphyry chalcopyrite leads to the higher copper dissolution rate of the pyritic chalcopyrite. In addition, the zeta-potential of chalcopyrite before and after bioleaching further confirms that ATF6 is more easily adsorbed onto the pyritic chalcopyrite.

  8. Pressure leaching of chalcopyrite concentrate

    Science.gov (United States)

    Aleksei, Kritskii; Kirill, Karimov; Stanislav, Naboichenko

    2018-05-01

    The results of chalcopyrite concentrate processing using low-temperature and high-temperature sulfuric acid pressure leaching are presented. A material of the following composition was used, 21.5 Cu, 0.1 Zn, 0.05 Pb, 0.04 Ni, 26.59 S, 24.52 Fe, 16.28 SiO2 (in wt.%). The influence of technological parameters on the degree of copper and iron extraction into the leach solution was studied in the wide range of values. The following conditions were suggested as the optimal for the high-temperature pressure leaching: t = 190 °C, PO2 = 0.5 MPa, CH2SO4 = 15 g/L, L:S = 6:1. At the mentioned parameters, it is possible to extract at least 98% Cu from concentrate into the leaching solution during 100 minutes. The following conditions were suggested as optimal for the low-temperature pressure leaching: t = 105 °C, PO2 = 1.3-1.5 MPa, CH2SO4 = 90 g/L, L:S = 10:1. At the mentioned parameters, it is possible to extract up to 83% Cu from the concentrate into the leach solution during 300-360 minutes.

  9. Current scenario of chalcopyrite bioleaching: a review on the recent advances to its heap-leach technology.

    Science.gov (United States)

    Panda, Sandeep; Akcil, Ata; Pradhan, Nilotpala; Deveci, Haci

    2015-11-01

    Chalcopyrite is the primary copper mineral used for production of copper metal. Today, as a result of rapid industrialization, there has been enormous demand to profitably process the low grade chalcopyrite and "dirty" concentrates through bioleaching. In the current scenario, heap bioleaching is the most advanced and preferred eco-friendly technology for processing of low grade, uneconomic/difficult-to-enrich ores for copper extraction. This paper reviews the current status of chalcopyrite bioleaching. Advanced information with the attempts made for understanding the diversity of bioleaching microorganisms; role of OMICs based research for future applications to industrial sectors and chemical/microbial aspects of chalcopyrite bioleaching is discussed. Additionally, the current progress made to overcome the problems of passivation as seen in chalcopyrite bioleaching systems have been conversed. Furthermore, advances in the designing of heap bioleaching plant along with microbial and environmental factors of importance have been reviewed with conclusions into the future prospects of chalcopyrite bioleaching. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Performance Analysis of Thiocarbonohydrazide as a Novel Selective Depressant for Chalcopyrite in Molybdenite-Chalcopyrite Separation

    Directory of Open Access Journals (Sweden)

    Changping Guan

    2018-04-01

    Full Text Available A novel surfactant, thiocarbonohydrazide (TCH, was synthesized and tested for the first time as a selective chalcopyrite depressant in Cu-Mo separation. Its adsorption mechanisms on chalcopyrite were studied by flotation tests, zeta potential, FTIR, XPS and ToF-SIMS measurements. FTIR and zeta potential analyses suggested that there was a strong chemisorption reaction between TCH and chalcopyrite, resulting in the formation of TCH–copper complexes. XPS and ToF-SIMS measurements further confirmed the chemisorption of TCH onto the chalcopyrite surface and showed that this chemisorption reaction is due to its S and N atoms, which form five-membered chelating rings by releasing H ions.

  11. Ball milling of chalcopyrite: Moessbauer spectroscopy and XRD studies

    International Nuclear Information System (INIS)

    Pollak, H.; Fernandes, M.; Levendis, D.; Schonig, L.

    1999-01-01

    The aim of this project is to study the behavior of chalcopyrite under ball milling for extended periods in order to determine how it's decompose or transform. Tests were done with chalcopyrite mixed with iron and zinc with and without surfactant. The use of surfactants has various effects such as avoiding oxidation and clustering of the fine particles. In all case magnetic chalcopyrite is transformed into a paramagnetic component showing a disordered structure, thus revealing that Cu atoms have replaced Fe atoms. In the case of ball milling in air, chalcopyrite is decomposed with the lost of iron, while in milling under surfactants, iron enters into the chalcopyrite structure. (author)

  12. The structure of reconstructed chalcopyrite surfaces

    Science.gov (United States)

    Thinius, Sascha; Islam, Mazharul M.; Bredow, Thomas

    2018-03-01

    Chalcopyrite (CuFeS2) surfaces are of major interest for copper exploitation in aqueous solution, called leaching. Since leaching is a surface process knowledge of the surface structure, bonding pattern and oxidation states is important for improving the efficiency. At present such information is not available from experimental studies. Therefore a detailed computational study of chalcopyrite surfaces is performed. The structures of low-index stoichiometric chalcopyrite surfaces {hkl} h, k, l ∈ {0, 1, 2} have been studied with density functional theory (DFT) and global optimization strategies. We have applied ab initio molecular dynamics (MD) in combination with simulated annealing (SA) in order to explore possible reconstructions via a minima hopping (MH) algorithm. In almost all cases reconstruction involving substantial rearrangement has occurred accompanied by reduction of the surface energy. The analysis of the change in the coordination sphere and migration during reconstruction reveals that S-S dimers are formed on the surface. Further it was observed that metal atoms near the surface move toward the bulk forming metal alloys passivated by sulfur. The obtained surface energies of reconstructed surfaces are in the range of 0.53-0.95 J/m2.

  13. Chalcopyrite semiconductors for quantum well solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Afshar, Maziar; Sadewasser, Sascha; Albert, Juergen; Lehmann, Sebastian; Abou-Ras, Daniel; Lux-Steiner, Martha C. [Helmholtz-Zentrum Berlin fuer Materialien und Energie, Berlin (Germany); Marron, David Fuertes [Instituto de Energia Solar - ETSIT, Universidad Politecnica de Madrid, Ciudad Universitaria s.n., 28040 Madrid (Spain); Rockett, Angus A. [Department of Materials Science and Engineering, University of Illinois, 1304 W. Green Street, Urbana, IL 61801 (United States); Raesaenen, Esa [Nanoscience Center, Department of Physics University of Jyvaeskylae, FI-40014 Jyvaeskylae (Finland)

    2011-11-15

    The possibilities of using highly absorbing chalcopyrite semiconductors of the type Cu(In,Ga)Se{sub 2} in a quantum well solar cell structure are explored. Thin alternating layers of 50 nm CuInSe{sub 2} and CuGaSe{sub 2} were grown epitaxially on a GaAs(100) substrate. The optical properties of a resulting structure of three layers indicate charge carrier confinement in the low band gap CuInSe{sub 2} layer. By compositional analysis interdiffusion of In and Ga at the interfaces was found. The compositional profile was converted into a conduction-band diagram, for which the quantization of energy levels was numerically confirmed using the effective-mass approximation. The results provide a promising basis for the future development of chalcopyrite-type quantum well structures and their application, i.e. in quantum well solar cells. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Raman spectroscopic study of some chalcopyrite-xanthate flotation products

    CSIR Research Space (South Africa)

    Andreev, GN

    2003-12-16

    Full Text Available of normal vibrations of the corresponding individual compounds. The latter facilitated the Raman spectroscopic elucidation of the reaction products formed on the chalcopyrite surface in real industrial flotation conditions with a sodium isopropyl xanthate...

  15. Effect of amino acids on bioleaching of chalcopyrite ore by ...

    African Journals Online (AJOL)

    Diptajeet

    2012-01-26

    Jan 26, 2012 ... ferrooxidans. Efficiency of microbial leaching of chalcopyrite by T. ferrooxidans was investigated in the .... Devasia P, Natarajan KA, Sathyanarayana DN, Ramananda Rao G. (1993). Surface ... Effects of L-cysteine on Ni-Cu.

  16. Effect of Sodium Sulfite on Floatability of Chalcopyrite and Molybdenite

    Directory of Open Access Journals (Sweden)

    Hajime Miki

    2018-04-01

    Full Text Available Sodium hydrogen sulfide (NaHS is commonly used as a copper depressant in the selective flotation of copper and molybdenum ores. However, the process is facing health and safety issues because NaHS readily yields toxic hydrogen sulfide gas (H2S under acidic conditions. In this study, Na2SO3 was proposed as an alternative copper depressant. The effect of Na2SO3 on the surface wettability and floatability of chalcopyrite and molybdenite—typical copper and molybdenum minerals, respectively—was intensively studied using contact angle measurements and flotation tests. Contact angle readings show that the chalcopyrite surface became hydrophilic after the Na2SO3 treatment. Meanwhile, the molybdenite surface was relatively more hydrophobic compared with that of chalcopyrite after the treatment. Flotation tests using pure minerals of chalcopyrite and molybdenite demonstrate that the floatability of chalcopyrite decreased with increasing concentration of Na2SO3. On the other hand, the floatability of molybdenite gradually increased under similar conditions, suggesting that Na2SO3 might have the potential to be used for selective flotation of chalcopyrite and molybdenite. A possible mechanism is proposed in this study to explain the phenomenon using X-ray photoelectron spectroscopy analysis.

  17. Processes for chalcopyrite-based solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Lux-Steiner, M.C.; Ennaoui, A.; Fischer, C.-H.; Jaeger-Waldau, A.; Klaer, J.; Klenk, R.; Koenenkamp, R.; Matthes, T.; Scheer, R.; Siebentritt, S.; Weidinger, A. [Hahn-Meitner-Institut Berlin GmbH (Germany)

    2000-02-21

    This contribution deals with the investigations of chalcopyrite solar cells. Main attention is paid to absorber materials with band gaps larger than 1.5 eV. Besides the different efforts to modify and optimise stoichiometric CuInS{sub 2} films, novel deposition technologies for CuGaSe{sub 2} films and buffer layers as well as alternative buffer layers were studied and compared. With ZnSe as alternative buffer layer on Cu(InGa)(S,Se){sub 2} absorbers developed by SSI Camarillo and Siemens Solar, Munich, total area efficiencies up to 13.7% and active area efficiencies up to 15.7% could be reached, respectively. For CuInS{sub 2} two important results were achieved. The efficiency of Cu-poor CuInS{sub 2} cells could be increased to 8.3%. Standard Cu-rich prepared devices led to a new record efficiency of 12.5%. (orig.)

  18. Selective separation of pyrite and chalcopyrite by biomodulation.

    Science.gov (United States)

    Chandraprabha, M N; Natarajan, K A; Modak, Jayant M

    2004-09-01

    Selective separation of pyrite from other associated ferrous sulphides at acidic and neutral pH has been a challenging problem. This paper discusses the utility of Acidithiobacillus ferrooxidans for the selective flotation of chalcopyrite from pyrite. Consequent to interaction with bacterial cells, pyrite remained depressed even in the presence of potassium isopropyl xanthate collector while chalcopyrite exhibited significant flotability. However, when the minerals were conditioned together, the selectivity achieved was poor due to the activation of pyrite surface by the copper ions in solution. The selectivity was improved when the sequence of conditioning with bacterial cells and collector was reversed, since the bacterial cells were able to depress collector interacted pyrite effectively, while having negligible effect on chalcopyrite. The observed behaviour is analysed and discussed in detail. The separation obtained was significant both at acidic and alkaline pH. This selectivity achieved was retained when the minerals were interacted with both bacterial cells and collector simultaneously.

  19. Catalytic effect of light illumination on bioleaching of chalcopyrite.

    Science.gov (United States)

    Zhou, Shuang; Gan, Min; Zhu, Jianyu; Li, Qian; Jie, Shiqi; Yang, Baojun; Liu, Xueduan

    2015-04-01

    The influence of visible light exposure on chalcopyrite bioleaching was investigated using Acidithiobacillus ferrooxidans. The results indicated, in both shake-flasks and aerated reactors with 8500-lux light, the dissolved Cu was 91.80% and 23.71% higher, respectively, than that in the controls without light. The catalytic effect was found to increase bioleaching to a certain limit, then plateaued as the initial chalcopyrite concentration increased from 2% to 4.5%. Thus a balanced mineral concentration is highly amenable to bioleaching via offering increased available active sites for light adsorption while eschewing mineral aggregation and screening effects. Using semiconducting chalcopyrite, the light facilitated the reduction of Fe(3+) to Fe(2+) as metabolic substrates for A.ferrooxidans, leading to better biomass, lower pH and redox potential, which are conducive to chalcopyrite leaching. The light exposure on iron redox cycling was further confirmed by chemical leaching tests using Fe(3+), which exhibited higher Fe(2+) levels in the light-induced system. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Electrochemical dissolution of chalcopyrite studied by voltammetry of immobilized microparticles

    Czech Academy of Sciences Publication Activity Database

    Pikna, L.; Lux, L.; Grygar, Tomáš

    2006-01-01

    Roč. 60, č. 4 (2006), s. 293-296 ISSN 0366-6352 Grant - others:VEGA(SK) No1/1108/04; APVT(SK) No20-009404 Institutional research plan: CEZ:AV0Z40320502 Keywords : chalcopyrite * cyclic voltammetry Subject RIV: CA - Inorganic Chemistry Impact factor: 0.360, year: 2006

  1. Bacterial consortium for copper extraction from sulphide ore consisting mainly of chalcopyrite

    Directory of Open Access Journals (Sweden)

    E. Romo

    2013-01-01

    Full Text Available The mining industry is looking forward for bacterial consortia for economic extraction of copper from low-grade ores. The main objective was to determine an optimal bacterial consortium from several bacterial strains to obtain copper from the leach of chalcopyrite. The major native bacterial species involved in the bioleaching of sulphide ore (Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans, Leptospirillum ferrooxidans and Leptospirillum ferriphilum were isolated and the assays were performed with individual bacteria and in combination with At. thiooxidans. In conclusion, it was found that the consortium integrated by At. ferrooxidans and At. thiooxidans removed 70% of copper in 35 days from the selected ore, showing significant differences with the other consortia, which removed only 35% of copper in 35 days. To validate the assays was done an escalation in columns, where the bacterial consortium achieved a higher percentage of copper extraction regarding to control.

  2. Quadrupole interaction in ternary chalcopyrite semiconductors experiments and theory

    CERN Document Server

    Dietrich, M; Degering, D; Deicher, M; Kortus, J; Magerle, R; Möller, A; Samokhvalov, V; Unterricker, S; Vianden, R

    2000-01-01

    Electric field gradients have been measured at substitutional lattice sites in ternary semiconductors using perturbed gamma - gamma angular correlation spectroscopy. The experimental results for A/sup I/B/sup III/C/sub 2//sup VI/ chalcopyrite structure compounds and Square Operator A/sup II/B/sub 2//sup III/C/sub 4//sup VI/ defect chalcopyrites are compared with ab-initio calculations. The latter were carried out with the WIEN code that uses the full potential linearized augmented plane wave method within a density functional theory. The agreement between experiment and theory is in most cases very good. Furthermore, the anion displacements in AgGaX/sub 2/- compounds (X: S, Se, Te) have been determined theoretically by determining the minimum of the total energy of the electrons in an elementary cell. (20 refs).

  3. Basic Research Opportunities in Cu-Chalcopyrite Photovoltaics: Preprint

    International Nuclear Information System (INIS)

    Rockett, A.; Bhattacharya, R. N.; Kapur, V.; Wei, S. H.

    1999-01-01

    A brief review is presented of fundamental research topics of primary importance to the development of improved solar cells based on chalcopyrite-structure materials. The opinions presented are a consensus opinion of the authors of the paper, with input from members of the chalcopyrite solar cells research community in the United States. Major topical areas identified included, in order of importance, are (1) development of an integrated predictive understanding of CIGS(S) materials and devices, (2) development of novel deposition techniques and characterization of the mechanisms of growth in existing and novel processes, (3) novel materials, especially with wide-energy gaps (is greater than or equal to 1.7 eV) other than Cu-based chalcopyrites, (4) development of real-time material characterizations for process control, and (5) alternative front- and rear-contact materials. Although the five topics identified are quite broad, they do not include all topics of interest. Also discussed briefly are some other potential research areas not in the highest priority topics, in particular, areas identified as primarily ''engineering'' rather than ''science.''

  4. Heterocoagulation of chalcopyrite and pyrite minerals in flotation separation.

    Science.gov (United States)

    Mitchell, Timothy K; Nguyen, Anh V; Evans, Geoffrey M

    2005-06-30

    Heterocoagulation between various fine mineral particles contained within a mineral suspension with different structural and surface chemistry can interfere with the ability of the flotation processes to selectively separate the minerals involved. This paper examines the interactions between chalcopyrite (a copper mineral) and pyrite (an iron mineral often bearing gold) as they approach each other in suspensions with added chemicals, and relates the results to the experimental data for the flotation recovery and selectivity. The heterocoagulation was experimentally studied using the electrophoretic light scattering (ELS) technique and was modelled by incorporating colloidal forces, including the van der Waals, electrostatic double layer and hydrophobic forces. The ELS results indicated that pyrite has a positive zeta potential (zeta) up to its isoelectric point (IEP) at approximately pH 2.2, while chalcopyrite has a positive zeta up to its IEP at approximately pH 5.5. This produces heterocoagulation of chalcopyrite with pyrite between pH 2.2 and pH 5.5. The heterocoagulation was confirmed by the ELS spectra measured with a ZetaPlus instrument from Brookhaven and by small-scale flotation experiments.

  5. The dissolution of chalcopyrite in chloride media; Lixiviacion de la calcopirita en medios clorurados

    Energy Technology Data Exchange (ETDEWEB)

    Ibanez, T.; Velasquez, L.

    2013-06-01

    The aim of this investigation is to determinate the effects of parameters and additives on the kinetics of dissolution of chalcopyrite on moderated conditions by means of dissolutions test with chalcopyrite concentrate and pure chalcopyrite in shake flasks and instrumented stirred reactors. A study of the dissolution of chalcopyrite in chloride solutions has demonstrated that the rate of dissolution of chalcopyrite is strongly dependent on the potential of the solution within a range of 540 to 630 mV (versus SHE). Leaching at pH around 2.5 results in increased rates of copper dissolution suggesting the possibility to keep the solution potential within the range. Both pyrite and silver ions enhance the dissolution of chalcopyrite and this effect increases when both species are present. The MnO{sub 2} has a negative effect on the dissolution increasing the solution potential to values where the rate decreases considerably. (Author)

  6. Synergistic bioleaching of chalcopyrite and bornite in the presence of Acidithiobacillus ferrooxidans.

    Science.gov (United States)

    Zhao, Hongbo; Wang, Jun; Hu, Minghao; Qin, Wenqing; Zhang, Yansheng; Qiu, Guanzhou

    2013-12-01

    Bioleaching of chalcopyrite and bornite in the presence of Acidithiobacillus ferrooxidans was carried out to investigate the influences between each other during bioleaching. Bioleaching results indicated that bornite accelerated the dissolution of chalcopyrite, and chalcopyrite also accelerated the dissolution of bornite, it could be described as a synergistic effect during bioleaching, this synergistic effect might be attributed to the galvanic effect between chalcopyrite and bornite, and to the relatively low solution potential as the addition of bornite. Significantly amount of elemental sulfur and jarosite formed on the minerals surface might be the main passivation film inhibiting the further dissolution, and the amount of elemental sulfur significantly increased with the addition of bornite. Results of electrochemical measurements indicated that the oxidation and reduction mechanisms of chalcopyrite and bornite were similar, the addition of bornite or chalcopyrite did not change the oxidative and reductive mechanisms, but increased the oxidation rate. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Effect of microwave-assisted heating on chalcopyrite leaching of kinetics, interface temperature and surface energy

    Directory of Open Access Journals (Sweden)

    Tong Wen

    Full Text Available The microwave-assisted leaching was a new approach to intensify the copper recovery from chalcopyrite by hydrometallurgy. In this work, the effect of microwave-assisted heating on chalcopyrite leaching of kinetics, interfacial reaction temperature and surface energy were investigated. The activation energy of chalcopyrite leaching was affected indistinctively by the microwave-assisted heating (39.1 kJ/mol compared with the conventional heating (43.9 kJ/mol. However, the boiling point of the leaching system increased through microwave-assisted heating. Because of the improved boiling point and the selective heating of microwave, the interfacial reaction temperature increased significantly, which gave rise to the increase of the leaching recovery of copper. Moreover, the surface energy of the chalcopyrite through microwave-assisted heating was also enhanced, which was beneficial to strengthen the leaching of chalcopyrite. Keywords: Microwave-assisted heating, Chalcopyrite, Leaching kinetics, Interface temperature, Surface energy

  8. Thin-film intermediate band chalcopyrite solar cells

    International Nuclear Information System (INIS)

    Fuertes Marron, D.; Marti, A.; Luque, A.

    2009-01-01

    Chalcopyrite-based solar cells currently lead the efficiency tables of thin-film photovoltaic technologies. Further improvements are foreseen upon implementation of an intermediate band in the absorber layers. We present a theoretical analysis of the efficiency limit for this type of device as a function of factors such as the gap of the host, the relative position of the intermediate band with respect to the band edge and the level of light concentration used as illumination. We have also considered the impact of non-idealities on the performance of the device, particularly the effect of electronic losses related to non-radiative recombination

  9. Co-Bioleaching of Chalcopyrite and Silver-Bearing Bornite in a Mixed Moderately Thermophilic Culture

    Directory of Open Access Journals (Sweden)

    Congren Yang

    2017-12-01

    Full Text Available Chalcopyrite and bornite are two important copper minerals, and they often coexist. In this study, the co-bioleaching of chalcopyrite and silver-bearing bornite by mixed moderately thermophilic culture at 50 °C was investigated. The bioleaching results show that the extraction percentage of Cu for co-bioleaching of chalcopyrite (Ccp and silver-bearing bornite (Bn (Ccp/Bn = 3:1 was 94.6%. Compared to bioleaching of chalcopyrite or silver-bearing bornite alone, the Cu extraction percentage was greatly enhanced when they were bioleached together. The leaching residues were characterized by X-ray diffraction (XRD and X-ray photoelectron spectroscopy (XPS. Silver-bearing bornite dissolved preferentially compared to chalcopyrite, due to galvanic interactions. Simultaneously, Ag+ was released from the silver-bearing bornite into solution. Ag2S formed on the surface because Cu and Fe in the chalcopyrite were replaced by Ag+, accelerating chalcopyrite dissolution and enrichment of Ag on the surface of the chalcopyrite.

  10. Insights into the relation between adhesion force and chalcopyrite-bioleaching by Acidithiobacillus ferrooxidans.

    Science.gov (United States)

    Zhu, Jianyu; Wang, Qianfen; Zhou, Shuang; Li, Qian; Gan, Min; Jiang, Hao; Qin, Wenqing; Liu, Xueduan; Hu, Yuehua; Qiu, Guanzhou

    2015-02-01

    This paper presents a study on the relation between bacterial adhesion force and bioleaching rate of chalcopyrite, which sheds light on the influence of interfacial interaction on bioleaching behavior. In our research, Acidithiobacillus ferrooxidans (A. ferrooxidans) were adapted to grow with FeSO4 · 7H2O, element sulfur or chalcopyrite. Then, surface properties of Acidithiobacillus ferrooxidans and chalcopyrite were analyzed by contact angle, zeta potential and Fourier transform infrared spectroscopy (FTIR). Adhesion force between bacteria and chalcopyrite was measured by atomic force microscopy (AFM). Attachment and bioleaching behaviors were also monitored. The results showed that A. ferrooxidans adapted with chalcopyrite exhibited the strongest adhesion force to chalcopyrite and the highest bioleaching rate. Culture adapted with sulfur bacteria took second place and FeSO4 · 7H2O-adapted bacteria were the lowest. Bioleaching rate and bacterial attachment capacity were positively related to bacterial adhesion force, which is affected by the nature of energy source. According to this work, the attachment of bacteria to chalcopyrite surface is one of the most important aspects that influence the bioleaching process of chalcopyrite. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Development of a composite collector scheme for flotation of chalcopyrite ore

    International Nuclear Information System (INIS)

    Khan, M.M.; Ahmad, I.

    2005-01-01

    Xanthate-type collectors reported for the upgradation of Chalcopyrite ore of North Waziristan area were studied and a new technique was developed, in which -two collectors were used (composite collectors) in the bulk-stage process of froth-flotation to achieve metallurgical grade with maximum recovery. The collectors studied were thiol-type surfactants, such as sodium ethyl xanthate (NaEX), sodium propyl xanthate (NaPX), sodium butyl xanthate (NaBX) and sodium Amyl xanthate (NaAX). Mixed collectors examined were in the varying dosage ratio of (0-100:100-0) through the combination of(i) sodium ethyl xanthate with sodium propyl xanthate, sodium ethyl xanthate with sodium butyl xanthate, sodium ethyl xanthate with sodium amyl xanthate, (ii) sodium propyl xanthate with sodium butyl xanthate, sodium propyl xanthate with sodium amyl xanthate and (iii) sodium butyl xanthate with sodium amyl xanthate. All the remaining flotation parameters were kept constant during the various flotation tests. The results were compared and the conclusions were drawn that the optimum grade in the concentrate was obtained with a mixture having a ratio of 4: 1 with sodium ethyl xanthate and sodium butyl xanthate. Recovery of copper content in the concentrate was achieved with ratio of 2:3 with sodium butyl xanthate and sodium amyl xanthate. (author)

  12. Galvanic enhancement for high pressure leaching of chalcopyrite

    Directory of Open Access Journals (Sweden)

    Kim D.H.

    2016-01-01

    Full Text Available This study was conducted to evaluate the galvanic enhancement of the pressure oxidation (POX leaching of a chalcopyrite/chalcocite concentrate, which is believed to take place via a redox reaction. Cu recoveries of >90% could be achieved during POX leaching of this chalcopyrite/chalcocite concentrate at 200°C and 0.7 MPa initial oxygen pressure within 2h in a pressure reactor lined with titanium, which were 18-28% higher than for the same leaching using the teflon liner. A slow heating time seems to produce more sulphur coating, reducing the leaching performance, yielding much lower Cu recovery when the teflon lining was used, although this does not greatly affect the other case when the reactor was lined with titanium. The introduction of an electronic conductor, in this case the titanium surface, is believed to enhance this redox process, in which the oxidation of copper minerals and sulphur to sulphate at the anodic sites (mineral surface encountered during POX leaching takes place simultaneously with the reversible oxidation/reduction of the Fe2+/Fe3+couple and oxygen reduction on titanium.

  13. Optimization of the use of carbon paste electrodes (CPE for electrochemical study of the chalcopyrite

    Directory of Open Access Journals (Sweden)

    Daniela G. Horta

    2009-01-01

    Full Text Available The use of carbon paste electrodes (CPE of mineral sulfides can be useful for electrochemical studies to overcome problems by using massive ones. Using CPE-chalcopyrite some variables were electrochemically evaluated. These variables were: (i the atmosphere of preparation (air or argon of CPE and elapsed time till its use; (ii scan rate for voltammetric measurements and (iii chalcopyrite concentration in the CPE. Based on cyclic voltammetry, open-circuit potential and electrochemical impedance results the recommendations are: oxygen-free atmosphere to prepare and kept the CPE until around two ours, scan rates from 10 to 40 mV s-1, and chalcopyrite concentrations > 20%.

  14. Comparative study on the selective chalcopyrite bioleaching of a molybdenite concentrate with mesophilic and thermophilic bacteria.

    Science.gov (United States)

    Romano, P; Blázquez, M L; Alguacil, F J; Muñoz, J A; Ballester, A; González, F

    2001-03-01

    This study evaluates different bioleaching treatments of a molybdenite concentrate using mesophilic and thermophilic bacterial cultures. Further studies on the chemical leaching and the electrochemical behavior of the MoS(2) concentrate were carried out. Bioleaching tests showed a progressive removal of chalcopyrite from the molybdenite concentrate with an increase in temperature. Chemical leaching tests support the idea of an indirect attack of the concentrate. Electrochemical tests indicate that chalcopyrite dissolution is favored when molybdenite is present. Therefore, this type of bioleaching treatment could be applied to purify molybdenite flotation concentrates by selectively dissolving chalcopyrite.

  15. Bioleaching of chalcopyrite and bornite by moderately thermophilic bacteria: an emphasis on their interactions

    Science.gov (United States)

    Zhao, Hong-bo; Wang, Jun; Gan, Xiao-wen; Qin, Wen-qing; Hu, Ming-hao; Qiu, Guan-zhou

    2015-08-01

    Interactions between chalcopyrite and bornite during bioleaching by moderately thermophilic bacteria were investigated mainly by X-ray diffraction, scanning electron microscopy, and electrochemical measurements performed in conjunction with bioleaching experiments. The results showed that a synergistic effect existed between chalcopyrite and bornite during bioleaching by both Acidithiobacillus caldus and Leptospirillum ferriphilum and that extremely high copper extraction could be achieved when chalcopyrite and bornite coexisted in a bioleaching system. Bornite dissolved preferentially because of its lower corrosion potential, and its dissolution was accelerated by the galvanic current during the initial stage of bioleaching. The galvanic current and optimum redox potential of 390-480 mV vs. Ag/AgCl promoted the reduction of chalcopyrite to chalcocite (Cu2S), thus accelerating its dissolution.

  16. Bioleaching of two different genetic types of chalcopyrite and their comparative mineralogical assessment.

    Science.gov (United States)

    Deng, Sha; Gu, Guohua; Ji, Jing; Xu, Baoke

    2018-02-01

    The bioleaching of two different genetic types of chalcopyrite by the moderate thermophile Sulfobacillus thermosulfidooxidans was investigated by leaching behaviors elucidation and their comparative mineralogical assessment. The leaching experiment showed that the skarn-type chalcopyrite (STC) revealed a much faster leaching rate with 33.34% copper extracted finally, while only 23.53% copper was bioleached for the porphyry-type chalcopyrite (PTC). The mineralogical properties were analyzed by XRD, SEM, XPS, and Fermi energy calculation. XRD indicated that the unit cell volume of STC was a little larger than that of PTC. SEM indicated that the surface of STC had more steps and ridges. XPS spectra showed that Cu(I) was the dominant species of copper on the surfaces of the two chalcopyrite samples, and STC had much more copper with lower Cu 2p 3/2 binding energy. Additionally, the Fermi energy of STC was much higher than that of PTC. These mineralogical differences were in good agreement with the bioleaching behaviors of chalcopyrite. This study will provide some new information for evaluating the oxidation kinetics of chalcopyrite.

  17. Synthesis of nanoparticle emulsion collector HNP and its application in microfine chalcopyrite flotation

    Science.gov (United States)

    He, G. C.; Ding, J.; Huang, C. H.; Kang, Q.

    2018-01-01

    Hydrophobic polystyrene nanoparticles bearing thiazole groups named HNP were used as collectors to improve recovery of microfine chalcopyrite in flotation. HNP adsorbs onto microfine particles selectively, which were modified hydrophobically to induce flotation effectively. Particle size and scanning electron microscope analysis for HNP show that HNP is a spherical nano particles with small size, uniform distribution and good dispersion. Infrared spectrum analysis for HNP proved that functional monomer 2-mercapto styrene acrylic thiazole was bonded chemically onto styrene. Flotation test results indicate that HNP is the right collector of chalcopyrite. Especially, the recovery of chalcopyrite is higher than 95% in neutral and acid media. FTIR results reveal that the flotation selectivity of collector HNP is due to strong chemical absorption onto chalcopyrite surface. Zeta potential analysis shows that the zeta potential of chalcopyrite decreased more quickly after interaction with HNP with the increase of pulp pH value, confirming that collector HNP is an anionic collector. Scanning electron microscope conform that HNP has good selective adsorption on chalcopyrite.

  18. Electronic structure of epitaxial chalcopyrite surfaces and interfaces for photovoltaics

    International Nuclear Information System (INIS)

    Hofmann, Andreas

    2012-01-01

    This thesis constitutes a comprehensive study of the surface physics of epitaxial CuInSe 2 films. It comprises analyses of the surface morphology and reconstruction, electronic band structure as well as hetero-junctions relevant to photovoltaic applications. Therefore, especially the aspect of stoichiometry variation from the CuInSe 2 to the copper-deficient defect phases was considered. Preparation and analysis was completely performed under ultra-high vacuum conditions in order to ensure the investigation of well-defined samples free of contaminants. For some of the analysis techniques, single-crystalline samples are indispensable: They allow for the determination of surface periodicity by low-energy electron diffraction (LEED). In combination with concentration depth profiling by angle-resolved x-ray photoemission, to types of surface reconstructions could be distinguished for the near-stoichiometric CuInSe 2 (112) surface. In the copper-rich case, it is stabilized by Cu In anti-site defects and on the indium-rich side by 2 V Cu defects, as predicted by surface total energy calculations by Jaffe and Zunger. Both configurations correspond to a c(4 x 2) reconstruction of the zinc blende type (111) surface. For the defect compound CuIn 3 Se 5 , a sphalerite order of the surface was found, which points at a weakening or absence of the chalcopyrite order in the bulk of the material. The unusual stability of the (112) surface could also be proven by comparison with the reconstruction and surface order of (001) and (220) surfaces. The results from surface analysis were used to measure the valence band structure of the epitaxial samples by synchrotron-based angle-resolved photoelectron spectroscopy. The CuInSe 2 (001) surface gives access to the high symmetry directions Γ-T and Γ-N of momentum space. By contrasting the data obtained for the stoichiometric surface with the copper-poor defect compound, a reduction of the valence band dispersion and a broadening of

  19. Electron microscope investigations of activated chalcopyrite particles via the FLSmidth® ROL process

    DEFF Research Database (Denmark)

    Karcz, Adam Paul; Damø, Anne Juul; Illerup, Jytte Boll

    2017-01-01

    Because of its unique semiconductor properties, the world’s most abundant copper mineral, chalcopyrite (CuFeS2), is refractory with respect to atmospheric leaching using traditional acidic ferric sulfate lixiviants. FLSmidth® has developed a novel approach manipulating lattice properties of semi.......1 and 5 mol percent of copper (II) to dope the lattice and thereby “activate” chalcopyrite. Since lattice restructuring can have such a dramatic influence on semiconductor reactivity, the associated physico-chemical phenomena are worth studying. In this regard, we investigate the relationship between...... chemical activation and deformation of the chalcopyrite crystal lattice through the use of electron microscopy. Although the activation process took only an hour and the extent of conversion was on the order of a few mol%, the lattice was found to be strained throughout the particle. This paper draws some...

  20. Galvanic Interaction between Chalcopyrite and Pyrite with Low Alloy and High Carbon Chromium Steel Ball

    Directory of Open Access Journals (Sweden)

    Asghar Azizi

    2013-01-01

    Full Text Available This study was aimed to investigate the galvanic interaction between pyrite and chalcopyrite with two types of grinding media (low alloy and high carbon chromium steel ball in grinding of a porphyry copper sulphide ore. Results indicated that injection of different gases into mill altered the oxidation-reduction environment during grinding. High carbon chromium steel ball under nitrogen gas has the lowest galvanic current, and low alloy steel ball under oxygen gas had the highest galvanic current. Also, results showed that the media is anodic relative to pyrite and chalcopyrite, and therefore pyrite or chalcopyrite with a higher rest potential acted as the cathode, whilst the grinding media with a lower rest potential acted as the anode, when they are electrochemically contacted. It was also found that low alloy steel under oxygen produced the highest amount of EDTA extractable iron in the slurry, whilst high carbon chromium steel under nitrogen atmosphere led to the lowest amount.

  1. Chalcopyrite Dissolution at 650 mV and 750 mV in the Presence of Pyrite

    Directory of Open Access Journals (Sweden)

    Yubiao Li

    2015-08-01

    Full Text Available The dissolution of chalcopyrite in association with pyrite in mine waste results in the severe environmental issue of acid and metalliferous drainage (AMD. To better understand chalcopyrite dissolution, and the impact of chalcopyrite’s galvanic interaction with pyrite, chalcopyrite dissolution has been examined at 75 °C, pH 1.0, in the presence of quartz (as an inert mineral and pyrite. The presence of pyrite increased the chalcopyrite dissolution rate by more than five times at Eh of 650 mV (SHE (Cu recovery 2.5 cf. 12% over 132 days due to galvanic interaction between chalcopyrite and pyrite. Dissolution of Cu and Fe was stoichiometric and no pyrite dissolved. Although the chalcopyrite dissolution rate at 750 mV (SHE was approximately four-fold greater (Cu recovery of 45% within 132 days as compared to at 650 mV in the presence of pyrite, the galvanic interaction between chalcopyrite and pyrite was negligible. Approximately all of the sulfur from the leached chalcopyrite was converted to S0 at 750 mV, regardless of the presence of pyrite. At this Eh approximately 60% of the sulfur associated with pyrite dissolution was oxidised to S0 and the remaining 40% was released in soluble forms, e.g., SO42−.

  2. Combined DFT and XPS investigation of iodine anions adsorption on the sulfur terminated (001) chalcopyrite surface

    Energy Technology Data Exchange (ETDEWEB)

    Li, Kui, E-mail: likui9606@stu.xjtu.edu.cn [School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Zhao, Yaolin, E-mail: zhaoyaolin@mail.xjtu.edu.cn [School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Zhang, Peng, E-mail: zp32@qq.com [Sino Shaanxi Nuclear Industry Group, Xi’an 710100 (China); He, Chaohui, E-mail: hechaohui@mail.xjtu.edu.cn [School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Deng, Jia, E-mail: djkokocase@stu.xjtu.edu.cn [School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Ding, Shujiang, E-mail: dingsj@mail.xjtu.edu.cn [Department of Applied Chemistry, School of Science, Xi’an Jiaotong University, Xi’an 710049 (China); Shi, Weiqun, E-mail: shiwq@ihep.ac.cn [Key Laboratory of Nuclear Radiation and Nuclear Energy Technology and Key Laboratory for Biomedical Effects of Nanomaterials and Nanosafety, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China)

    2016-12-30

    Highlights: • Metal surface sites of (001)-S surface of chalcopyrite show significant chemical affinity to iodide and iodate. • The energetically favorable active site is copper for iodide adsorption and iron for iodate adsorption, respectively. • Iodate undergoes a dissociative adsorption on the copper site of chalcopyrite surface. - Abstract: The adsorption of iodine anions (iodide and iodate) on the sulfur terminated (001) chalcopyrite surface has been systematically investigated combining first-principles calculations based on density functional theory (DFT) with X-ray photoelectron spectroscopy (XPS) measurements. Based on the total energy calculations and geometric optimization, the thermodynamically preferred site was copper atom for iodide adsorption and iron atom for iodate adsorption, respectively. In the case of Cu site mode, the iodate underwent a dissociative adsorption, where one I−O bond of iodate ion was broken and the dissociative oxygen atom adsorbed on the adjacent sulphur site. Projected density of states (PDOS) analysis further clarified the interaction mechanism between active sites of chalcopyrite surface and adsorbates. In addition, full-range XPS spectra qualitatively revealed the presence of iodine on chalcopyrite surface. High resolution XPS spectra of the I 3d peaks after adsorption verified the chemical environment of iodine. The binding energies of 618.8 eV and 623.5 eV for I 3d{sub 5/2} peaks unveiled that the adsorption of iodide and iodate ions on copper-iron sulfide minerals was the result of formation of low solubility metal iodides precipitate. Also two I 3d peaks with low intensity around 618 eV and 630 eV might be related to the inorganic reduction of iodate to iodide by reducing S{sup 2−} ion of chalcopyrite.

  3. Surface characterization of activated chalcopyrite particles via the FLSmidth ROL process. Part 1: Electron microscope investigations

    DEFF Research Database (Denmark)

    Karcz, Adam Paul; Damø, Anne Juul; Illerup, Jytte Boll

    Because of its unique semiconductor properties, the world’s most abundant copper mineral (chalcopyrite) is refractory with respect to atmospheric leaching using traditional ferric sulfate lixiviants. A novel approach to address this issue – conducted at FLSmidth – utilizes a mechanochemical Rapid...... of copper(II) to dope the semiconductor lattice and thereby "activate" the chalcopyrite, thereby reducing leach times below 2 hours (>98% recovery). Because the activation plays a major role in accelerating the leaching step, it is critical to understand the nature of this intermediate and its part...... in the ROL process. The current work presents results from electron microscope investigations of surface-activated particles....

  4. The influence of mechanical activation of chalcopyrite on the selective leaching of copper by sulphuric acid

    Directory of Open Access Journals (Sweden)

    Achimovičová, M.

    2006-01-01

    Full Text Available In this paper chalcopyrite, CuFeS2, has been selective leached by H2SO4 as leaching agent (170 g/dm3 in procedure of hydrometallurgical production of copper. Mechanical activation of the chalcopyrite resulted in mechanochemical surface oxidation as well as in the mineral surface and bulk disordering. Furthermore, the formation of agglomerates during grinding was also occured. Surface changes of the samples using infrared spectroscopy and scanning electron microscopy methods were investigated before and after leaching. The leaching rate, specific surface area, structural disorder as well as copper extraction increased with the mechanical activation of mineral.

  5. Advances in copper-chalcopyrite thin films for solar energy conversion

    Energy Technology Data Exchange (ETDEWEB)

    Kaneshiro, Jess; Gaillard, Nicolas; Rocheleau, Richard; Miller, Eric [Hawaii Natural Energy Institute, University of Hawaii at Manoa, 1680 East-West Road, Post 109, Honolulu, HI 96822 (United States)

    2010-01-15

    Promising alternatives to crystalline silicon as the basic building block of solar cells include copper-chalcopyrite thin films such as copper indium gallium diselenide, a class of thin films exhibiting bandgap-tunable semiconductor behavior, direct bandgaps and high absorption coefficients. These properties allow for the development of novel solar-energy conversion configurations like ultra-high efficiency multi-junction solar cells utilizing combinations of photovoltaic and photoelectrochemical junctions for hydrogen production. This paper discusses the current worldwide status as well as the development and optimization of copper-chalcopyrite thin films deposited onto various substrate types for different photovoltaic and photoelectrochemical applications at the Hawaii Natural Energy Institute. (author)

  6. A Moderately Thermophilic Mixed Microbial Culture for Bioleaching of Chalcopyrite Concentrate at High Pulp Density

    Science.gov (United States)

    Wang, Yuguang; Zeng, Weimin; Qiu, Guanzhou; Chen, Xinhua

    2014-01-01

    Three kinds of samples (acid mine drainage, coal mine wastewater, and thermal spring) derived from different sites were collected in China. Thereafter, these samples were combined and then inoculated into a basal salts solution in which different substrates (ferrous sulfate, elemental sulfur, and chalcopyrite) served as energy sources. After that, the mixed cultures growing on different substrates were pooled equally, resulting in a final mixed culture. After being adapted to gradually increasing pulp densities of chalcopyrite concentrate by serial subculturing for more than 2 years, the final culture was able to efficiently leach the chalcopyrite at a pulp density of 20% (wt/vol). At that pulp density, the culture extracted 60.4% of copper from the chalcopyrite in 25 days. The bacterial and archaeal diversities during adaptation were analyzed by denaturing gradient gel electrophoresis and constructing clone libraries of the 16S rRNA gene. The results show that the culture consisted mainly of four species, including Leptospirillum ferriphilum, Acidithiobacillus caldus, Sulfobacillus acidophilus, and Ferroplasma thermophilum, before adapting to a pulp density of 4%. However, L. ferriphilum could not be detected when the pulp density was greater than 4%. Real-time quantitative PCR was employed to monitor the microbial dynamics during bioleaching at a pulp density of 20%. The results show that A. caldus was the predominant species in the initial stage, while S. acidophilus rather than A. caldus became the predominant species in the middle stage. F. thermophilum accounted for the greatest proportion in the final stage. PMID:24242252

  7. Isolation of a strain of Acidithiobacillus caldus and its role in bioleaching of chalcopyrite

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Q.G.; Bo, F.; Bo, Z.H.; Xi, L.; Jian, G.; Fei, L.F.; Hua, C.X. [Central South University of Technology, Changsha (China)

    2007-09-15

    A moderately thermophilic and acidophilic sulfur-oxidizing bacterium named S-2, was isolated from coal heap drainage. The bacterium was motile, Gramnegative, rod-shaped, measured 0.4 to 0.6 by 1 to 2 gm, and grew optimally at 42-45{sup o}C and an initial pH of 2.5. The strain S-2 grew autotrophically by using elemental sulfur, sodium thiosulfate and potassium tetrathionate as energy sources. The strain did not use organic matter and inorganic minerals including ferrous sulfate, pyrite and chalcopyrite as energy sources. The morphological, biochemical, physiological characterization and analysis based on 16S rRNA gene sequence indicated that the strain S2 is most closely related to Acidithiobacillus caldus (> 99% similarity in gene sequence). The combination of the strain S-2 with Leptospirillum ferriphilum or Acidithiobacillus ferrooxidans in chalcopyrite bioleaching improved the copper-leaching efficiency. Scanning electron microscope (SEM) analysis revealed that the chalcopyrite surface in a mixed culture of Leptospirillum ferriphilum and Acidithiobacillus caldus was heavily etched. The energy dispersive X-ray (EDX) analysis indicated that Acidithiobacillus caldus has the potential role to enhance the recovery of copper from chalcopyrite by oxidizing the sulfur formed during the bioleaching progress.

  8. Selective depression mechanism of ferric chromium lignin sulfonate for chalcopyrite-galena flotation separation

    Science.gov (United States)

    Yu, Jin-sheng; Liu, Run-qing; Wang, Li; Sun, Wei; Peng, Hong; Hu, Yue-hua

    2018-05-01

    Selective recovery of chalcopyrite-galena ore by flotation remains a challenging issue. The development of highly efficient, low-cost, and environmentally friendly depressants for this flotation is necessary because most of available reagents (e.g., K2Cr2O4) are expensive and adversely affect the environment. In this study, ferric chromium lignin sulfonate (FCLS), which is a waste-product from the paper and pulp industry, was introduced as a selective depressant for galena with butyl xanthate (BX) as a collector. Results show that the residue recovery of Pb in Cu concentrate was substantially reduced to 4.73% using FCLS compared with 10.71% using the common depressant K2Cr2O4. The underlying mechanisms were revealed using zeta-potential measurements and X-ray photoelectron spectroscopy (XPS). Zeta-potential measurements revealed that FCLS was more efficiently absorbed onto galena than onto chalcopyrite. XPS measurements further suggested that FCLS enhanced the surface oxidation of galena but prevented that of chalcopyrite. Thus, FCLS could be a potential candidate as a depressant for chalcopyrite-galena flotation because of its low cost and its lack of detrimental effects on the environment.

  9. Fundamental Flotation Behaviors of Chalcopyrite and Galena Using O-Isopropyl-N-Ethyl Thionocarbamate as a Collector

    Directory of Open Access Journals (Sweden)

    Yongjie Bu

    2018-03-01

    Full Text Available Copper and lead are two important and widely used metals in industry. Chalcopyrite (CuFeS2 is associated with galena (PbS in ore, and it has been a research hotspot in separating galena from chalcopyrite by flotation. In this study, the flotation behaviors of chalcopyrite and galena were studied through flotation tests, adsorption measurements, solution chemistry calculation, Fourier transform infrared spectroscopy (FTIR and molecular dynamics (MD simulations. The results show that the floatability of chalcopyrite is better than that of galena in the presence of O-isopropyl-N-ethyl thionocarbamate (IPETC, and the recovery difference between chalcopyrite and galena is about 20% when IPETC is 7 × 10−4 mol/L at pH 9.5, while the floatability difference between the two minerals is significant. Competitive adsorption of OH− and IPETC on mineral surfaces leads to lower floatability of galena than that of chalcopyrite. IPETC is able to remove the hydration layer on mineral surfaces and then adsorb on active sites. The floatability of minerals is enhanced with the increase of their hydrophobicity. This study provides a reference to separate galena from chalcopyrite.

  10. Short communication: Adverse effect of surface-active reagents on the bioleaching of pyrite and chalcopyrite by Thiobacillus ferrooxidans.

    Science.gov (United States)

    Huerta, G; Escobar, B; Rubio, J; Badilla-Ohlbaum, R

    1995-09-01

    Oxidation of Fe(II) iron and bioleaching of pyrite and chalcopyrite by Thiobacillus ferrooxidans was adversely affected by isopropylxanthate, a flotation agent, and by LIX 984, a solvent-extraction agent, each at ≤ 1 g/l. The reagents/l were adsorbed on the bacterial surface, decreasing the bacteria's development and preventing biooxidation. Both reagents inhibited the bioleaching of pyrite and LIX 984 also inhibited the bioleaching of chalcopyrite.

  11. Grain-size distributions and grain boundaries of chalcopyrite-type thin films

    International Nuclear Information System (INIS)

    Abou-Ras, D.; Schorr, S.; Schock, H.W.

    2007-01-01

    CuInSe 2 , CuGaSe 2 , Cu(In,Ga)Se 2 and CuInS 2 thin-film solar absorbers in completed solar cells were studied in cross section by means of electronbackscatter diffraction. From the data acquired, grain-size distributions were extracted, and also the most frequent grain boundaries were determined. The grain-size distributions of all chalcopyrite-type thin films studied can be described well by lognormal distribution functions. The most frequent grainboundary types in these thin films are 60 - left angle 221 right angle tet and 71 - left angle 110 right angle tet (near) Σ3 twin boundaries. These results can be related directly to the importance of {112} tet planes during the topotactical growth of chalcopyrite-type thin films. Based on energetic considerations, it is assumed that the most frequent twin boundaries exhibit a 180 - left angle 221 right angle tet constellation. (orig.)

  12. Flotation performances and surface properties of chalcopyrite with xanthate collector added before and after grinding

    Science.gov (United States)

    Peng, Huiqing; Wu, Di; Abdelmonem, Mohamed

    In this study, effects of the collector added before grinding and after grinding on the subsequent flotation and mineral surface properties were investigated. The pH was controlled at 10 during the grinding and flotation processes opened to the atmosphere. With enough amounts of sodium butyl xanthate addition, adding the collector before grinding recovered more chalcopyrite than adding it after grinding in single mineral flotation. The Eh of each ground pulp before and after conditioning were measured and it was found that adding collector before grinding obtained higher and relatively suitable pulp potential for chalcopyrite flotation. Particle size analyses of the flotation products indicate that the different flotation recoveries occurred due to the different flotation losses in fine particles (flotation feedings and found that more carbon and oxygen, and less iron were remained on mineral surfaces when the collector was added before grinding, due to the higher collector adsorption capacity, larger free oxygen adsorbance and less iron oxide/hydroxide species.

  13. MODELLING CHALCOPYRITE LEACHING BY Fe+3 IONS WITH THE SHRINKING CORE MODEL

    Directory of Open Access Journals (Sweden)

    Rodrigo Rangel Porcaro

    2015-03-01

    Full Text Available Chalcopyrite leaching by ferric iron is considered a slow process with low copper recovery; a phenomenon ascribed to the passivation of the mineral surface during leaching. Thus, the current study investigated the leaching kinetics of a high purity chalcopyrite sample in the presence of ferric sulfate as oxidant. The effects of the stirring rate, temperature, Eh and Fe3+ concentration on copper extraction were assessed. The leaching data could be described by the shirking core model (SCM for particles of unchanging size and indicated diffusion in the ash layer as the rate-controlling step with a high activation energy (103.9±6.5kJ/mol; likely an outcome of neglecting the effect of particle size distribution (PSD on the kinetics equations. Both the application of the quasi-steady-state assumption to solid-liquid systems and the effect of the particle size distribution on the interpretation of kinetics data are also discussed.

  14. Optical properties of chalcopyrite-type intermediate transition metal band materials from first principles

    International Nuclear Information System (INIS)

    Aguilera, I.; Palacios, P.; Wahnon, P.

    2008-01-01

    The optical properties of a novel potential high-efficiency photovoltaic material have been studied. This material is based on a chalcopyrite-type semiconductor (CuGaS 2 ) with some Ga atom substituted by Ti and is characterized by the formation of an isolated transition-metal band between the valence band and the conduction band. We present a study in which ab-initio density functional theory calculations within the generalized gradient approximation are carried out to determine the optical reflectivity and absorption coefficient of the materials of interest. Calculations for the host semiconductor are in good agreement with experimental results within the limitations of the approach. We find, as desired, that because of the intermediate band, the new Ti-substituted material would be able to absorb photons of energy lower than the band-gap of the host chalcopyrite. We also analyze the partial contributions to the main peaks of its spectrum

  15. Evolution of Sulfobacillus thermosulfidooxidans secreting alginate during bioleaching of chalcopyrite concentrate.

    Science.gov (United States)

    Yu, R-L; Liu, A; Liu, Y; Yu, Z; Peng, T; Wu, X; Shen, L; Liu, Y; Li, J; Liu, X; Qiu, G; Chen, M; Zeng, W

    2017-06-01

    To explore the distribution disciplinarian of alginate on the chalcopyrite concentrate surface during bioleaching. The evolution of Sulfobacillus thermosulfidooxidans secreting alginate during bioleaching of chalcopyrite concentrate was investigated through gas chromatography coupled with mass spectrometry (GC-MS) and confocal laser scanning microscope (CLSM), and the critical synthetic genes (algA, algC, algD) of alginate were analysed by real-time polymerase chain reaction (RT-PCR). The GC-MS analysis results indicated that there was a little amount of alginate formed on the mineral surface at the early stage, while increasing largely to the maximum value at the intermediate stage, and then kept a stable value at the end stage. The CLSM analysis of chalcopyrite slice showed the same variation trend of alginate content on the mineral surface. Furthermore, the RT-PCR results showed that during the early stage of bioleaching, the expressions of the algA, algC and the algD genes were all overexpressed. However, at the final stage, the algD gene expression decreased in a large scale, and the algA and algC decreased slightly. This expression pattern was attributed to the fact that algA and algC genes were involved in several biosynthesis reactions, but the algD gene only participated in the alginate biosynthesis and this was considered as the key gene to control alginate synthesis. The content of alginate on the mineral surface increased largely at the beginning of bioleaching, and remained stable at the end of bioleaching due to the restriction of algD gene expression. Our findings provide valuable information to explore the relationship between alginate formation and bioleaching of chalcopyrite. © 2017 The Society for Applied Microbiology.

  16. Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

    OpenAIRE

    Wang Lan; Lin Xianzhong; Ennaoui Ahmed; Wolf Christian; Lux-Steiner Martha Ch.; Klenk Reiner

    2016-01-01

    We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating ...

  17. Passivation of chalcopyrite during the leaching with sulphuric acid solution in presence of sodium nitrate

    Directory of Open Access Journals (Sweden)

    Sokić Miroslav D.

    2010-01-01

    Full Text Available In this work, the process of the chalcopyrite leaching in sulphuric acid solution was investigated. Sodium nitrate was used as oxidant in the leaching process. Chemical reactions of leaching and their thermodynamic possibilities are predicted based on the calculated Gibbs energies and analysis of E−pH diagrams. The negative values of the Gibbs energy show that all chemical reactions are thermodynamically feasible at atmospheric pressure and in a temperature range 25-90°C. At high electrode potential and low pH values, Cu2+, Fe2+ and Fe3+ ions exist in water solutions. The increase of temperature reduces the probability of Fe3+ ion existence in the system. The chalcopyrite concentrate, enriched in the “Rudnik” flotation plant, with 27.08% Cu, 25.12% Fe, 4.15% Zn and 2.28% Pb was used in the work. XRD and DTA analysis of the concentrate reveals that the sample contains mainly the chalcopyrite with small amount of sphalerite. For the description of the reaction of leaching process the leach residuals, obtained at different conditions, were chosen for XRD, TG/DTA and SEM/EDX analyses. The elemental sulphur and chalcopyrite phases identified in leach residuals confirm our prediction that the elemental sulphur is formed during the leaching process. Accordingly, elemental sulphur is the main product of the reaction, while a minor amount of sulphide sulphur is oxidized to sulphate during the leaching. The sulphur formed during the reaction was precipitated at the particle surfaces, and slowed down the leaching rate in the final stage of leaching process. In the initial stage, the reaction rate was controlled by the surface reaction. The mechanism, latter has been changed into a diffusion controlled one.

  18. Diffusion in copper sulphides. An experimental study of chalcocite, chalcopyrite and bornite

    International Nuclear Information System (INIS)

    Berger, R.; Bucur, R.V.

    1996-01-01

    Diffusion measurements on three copper-containing sulphides have been performed by an electrochemical potentiometric method. Chalcocite (Cu 2 S), Chalcopyrite (CuFeS 2 ) and Bornite (Cu 5 FeS 4 ) were synthesized and fully characterized by X-ray diffraction. The diffusivities were measured on compacted powders yielding both the chemical and the component diffusion coefficients in the temperature range 5-50 C. The chemical diffusion coefficients found were: for Chalcocite 38.7*exp (-5600/T), for Chalcopyrite 15.4*exp(-6000/T) and for Bornite 14.4*exp(-4900/T). The diffusion coefficient for Chalcocite is in good agreement with values found previously, and a reasonable agreement is also found for Chalcopyrite and Bornite when our data are compared with values acquired at much higher temperatures with a different technique. The activation energies (here on a Kelvin scale) are remarkably similar for the three sulfides, considering that their relative errors are of a 10% magnitude, which indicates that the bonding strengths and the diffusion mechanisms are similar. The chemical diffusion coefficients which enter the empirical Fick's diffusion laws that describe concentration changes, are of the order of exp(-8) to exp (-7) cm 2 /s at room temperature. Such values bring the ion mobilities near values found for solid state 'fast ion conductors', used as electrolytes at elevated temperatures. 17 refs, 8 figs, 5 tabs

  19. Synthesis of Novel Ether Thionocarbamates and Study on Their Flotation Performance for Chalcopyrite

    Directory of Open Access Journals (Sweden)

    Gang Zhao

    2016-09-01

    Full Text Available Novel ether thionocarbamates, O-butoxy isopropyl-N-ethoxycarbonyl thionocarbamate (BIPECTC and O-(2-butoxy-1-methylethoxy isopropyl-N-ethoxycarbonyl thionocarbamate (BMIPECTC, were synthesized in this study. Their collecting efficiencies in the flotation of chalcopyrite were investigated using flotation tests, adsorption measurements, ultraviolet spectra (UV and Fourier transform-infrared spectroscopy (FT-IR and density functional theory (DFT calculations. The synthesized ether thionocarbamates showed better frothing properties than methyl-isobutyl-carbinol (MIBC and stronger affinity to chalcopyrite compared with O-isopropyl-N-ethyl thionocarbamate (IPETC and O-isobutyl-N-ethoxycarbonyl thionocarbamate (IBECTC. UV spectra analysis showed that the ether thionocarbamates react with Cu2+, with the exception of Fe2+, Ni2+, Zn2+ and Pb2+. Additionally, it was further confirmed by FTIR spectra that a chemical reaction occurs between copper ion and BIPECTC and BMIPECTC. The adsorption capacity measurements revealed that chalcopyrite exhibits good adsorption ability for ether thionocarbamates at an approximate pH of 8–10, which agrees with the flotation tests. The quantum chemistry calculation results indicated that the ether thionocarbamates exhibit stronger collecting ability for copper mineral in terms of frontier molecular orbital analysis, binding model simulation with copper ions and the molecular hydrophobicity compared with IPETC and IBECTC. The computational results are in very good agreement with the experimental results.

  20. Diffusion in copper sulphides. An experimental study of chalcocite, chalcopyrite and bornite

    Energy Technology Data Exchange (ETDEWEB)

    Berger, R; Bucur, R V [Uppsala Univ. (Sweden). Inst. of Chemistry

    1996-01-01

    Diffusion measurements on three copper-containing sulphides have been performed by an electrochemical potentiometric method. Chalcocite (Cu{sub 2}S), Chalcopyrite (CuFeS{sub 2}) and Bornite (Cu{sub 5}FeS{sub 4}) were synthesized and fully characterized by X-ray diffraction. The diffusivities were measured on compacted powders yielding both the chemical and the component diffusion coefficients in the temperature range 5-50 C. The chemical diffusion coefficients found were: for Chalcocite 38.7*exp (-5600/T), for Chalcopyrite 15.4*exp(-6000/T) and for Bornite 14.4*exp(-4900/T). The diffusion coefficient for Chalcocite is in good agreement with values found previously, and a reasonable agreement is also found for Chalcopyrite and Bornite when our data are compared with values acquired at much higher temperatures with a different technique. The activation energies (here on a Kelvin scale) are remarkably similar for the three sulfides, considering that their relative errors are of a 10% magnitude, which indicates that the bonding strengths and the diffusion mechanisms are similar. The chemical diffusion coefficients which enter the empirical Fick`s diffusion laws that describe concentration changes, are of the order of exp(-8) to exp (-7) cm{sup 2}/s at room temperature. Such values bring the ion mobilities near values found for solid state `fast ion conductors`, used as electrolytes at elevated temperatures. 17 refs, 8 figs, 5 tabs.

  1. Investigation of energy gene expressions and community structures of free and attached acidophilic bacteria in chalcopyrite bioleaching.

    Science.gov (United States)

    Zhu, Jianyu; Jiao, Weifeng; Li, Qian; Liu, Xueduan; Qin, Wenqing; Qiu, Guanzhou; Hu, Yuehua; Chai, Liyuan

    2012-12-01

    In order to better understand the bioleaching mechanism, expression of genes involved in energy conservation and community structure of free and attached acidophilic bacteria in chalcopyrite bioleaching were investigated. Using quantitative real-time PCR, we studied the expression of genes involved in energy conservation in free and attached Acidithiobacillus ferrooxidans during bioleaching of chalcopyrite. Sulfur oxidation genes of attached A. ferrooxidans were up-regulated while ferrous iron oxidation genes were down-regulated compared with free A. ferrooxidans in the solution. The up-regulation may be induced by elemental sulfur on the mineral surface. This conclusion was supported by the results of HPLC analysis. Sulfur-oxidizing Acidithiobacillus thiooxidans and ferrous-oxidizing Leptospirillum ferrooxidans were the members of the mixed culture in chalcopyrite bioleaching. Study of the community structure of free and attached bacteria showed that A. thiooxidans dominated the attached bacteria while L. ferrooxidans dominated the free bacteria. With respect to available energy sources during bioleaching of chalcopyrite, sulfur-oxidizers tend to be on the mineral surfaces whereas ferrous iron-oxidizers tend to be suspended in the aqueous phase. Taken together, these results indicate that the main role of attached acidophilic bacteria was to oxidize elemental sulfur and dissolution of chalcopyrite involved chiefly an indirect bioleaching mechanism.

  2. Study of the Effect of Sodium Sulfide as a Selective Depressor in the Separation of Chalcopyrite and Molybdenite

    Directory of Open Access Journals (Sweden)

    Huiqing Peng

    2017-03-01

    Full Text Available Two kinds of collectors, sodium butyl xanthate and kerosene, and a depressor, sodium sulfide, were used in this research. The study applied flotation tests, pulp potential measurements, contact angle measurements, adsorption calculations, and Fourier Transform Infrared Spectroscopy (FTIR analyses to demonstrate the correlation between reagents and minerals. For xanthate collectors, the best flotation responses of chalcopyrite and molybdenite were obtained at pH = 8, and, for kerosene, these were obtained at pH = 4. The flotation of molybdenite seemed to be less influenced by xanthate than by kerosene, while that of chalcopyrite showed the opposite. The optimum concentration of sodium sulfide for separation was 0.03 mol/L, which rejected 83% chalcopyrite and recovered 82% molybdenite in the single mineral flotation. Pulp potential measurements revealed that the dixanthogen and xanthate were decomposed and desorbed, respectively, from the mineral surface in a reducing environment. The contact angle measurement and adsorption calculation conformed to the flotation response, indicating that few functions of the xanthate and sodium sulfide on the molybdenite flotation were due to their low adsorption densities. The FTIR results further clarified that the xanthate ion was adsorbed on chalcopyrite by forming cuprous xanthate and dixanthogen; however, on molybdenite the adsorption product was only dixanthogen. After conditioning with sodium sulfide, the chalcopyrite surface became clean, but the molybdenite surface still retained slight peaks of dixanthogen. Meanwhile, the possible mechanism was expounded in this research.

  3. Magnetic exchange interactions in Mn doped ZnSnAs{sub 2} chalcopyrite

    Energy Technology Data Exchange (ETDEWEB)

    Bouhani-Benziane, H.; Sahnoun, O. [Laboratoire de Physique Quantique de la Matière et Modélisation Mathématique (LPQ3M), University of Mascara (Algeria); Sahnoun, M., E-mail: sahnoun_cum@yahoo.fr [Laboratoire de Physique Quantique de la Matière et Modélisation Mathématique (LPQ3M), University of Mascara (Algeria); Department of Chemistry, University of Fribourg (Switzerland); Driz, M. [Laboratoire de Sciences des Matériaux (LSM), University of Sidi Bel Abbes (Algeria); Daul, C. [Department of Chemistry, University of Fribourg (Switzerland)

    2015-12-15

    Accurate ab initio full-potential augmented plane wave (FP-LAPW) electronic calculations within generalized gradient approximation have been performed for Mn doped ZnSnAs{sub 2} chalcopyrites, focusing on their electronic and magnetic properties as a function of the geometry related to low Mn-impurity concentration and the spin magnetic alignment (i.e., ferromagnetic vs antiferromagnetic). As expected, Mn is found to be a source of holes and localized magnetic moments of about 4 µ{sub B} per Mn atom are calculated which are sufficiently large. The defect calculations are firstly performed by replacing a single cation (namely Zn and Sn) with a single Mn atom in the pure chalcopyrite ZnSnAs{sub 2} supercell, and their corresponding formation energies show that the substitution of a Sn atom (rather than Zn) by Mn is strongly favored. Thereafter, a comparison of total energy differences between ferromagnetic (FM) and antiferromagnetic (AFM) are given. Surprisingly, the exchange interaction between a Mn pairs is found to oscillate with the distance between them. Consequently, the AFM alignment is energetically favored in Mn-doped ZnSnAs{sub 2} compounds, except for low impurity concentration associated with lower distances between neighboring Mn impurities, in this case the stabilization of FM increases. Moreover, the ferromagnetic alignment in the Mn-doped ZnSnAs{sub 2} systems behaves half-metallic; the valence band for majority spin orientation is partially filled while there is a gap in the density of states for the minority spin orientation. This semiconducting gap of ~1 eV opened up in the minority channel and is due to the large bonding–antibonding splitting from the p–d hybridization. Our findings suggest that the Mn-doped ZnSnAs{sub 2} chalcopyrites could be a different class of ferromagnetic semiconductors. - Highlights: • ab initio calculations were performed on Mn doped ZnSnAs{sub 2} chalcopyrite. • Substitution of a Sn atom (rather than Zn) by Mn

  4. Ab-initio vibrational properties of transition metal chalcopyrite alloys determined as high-efficiency intermediate-band photovoltaic materials

    International Nuclear Information System (INIS)

    Palacios, P.; Aguilera, I.; Wahnon, P.

    2008-01-01

    In this work, we present frozen phonon and linear response ab-initio research into the vibrational properties of the CuGaS 2 chalcopyrite and transition metal substituted (CuGaS 2 )M alloys. These systems are potential candidates for developing a novel solar-cell material with enhanced optoelectronic properties based in the implementation of the intermediate-band concept. We have previously carried out ab-initio calculations of the electronic properties of these kinds of chalcopyrite metal alloys showing a narrow transition metal band isolated in the semiconductor band gap. The substitutes used in the present work are the 3d metal elements, Titanium and Chromium. For the theoretical calculations we use standard density functional theory at local density and generalized gradient approximation levels. We found that the optical phonon branches of the transition metal chalcopyrite, are very sensitive to the specific bonding geometry and small changes in the transition metal environment

  5. Pressure dependence of Raman modes in the chalcopyrite quaternary alloy AgxCu1-xGaS2

    International Nuclear Information System (INIS)

    Choi, In-Hwan; Yu, Peter Y.

    2000-01-01

    Raman scattering in the chalcopyrite quaternary alloy Ag x Cu 1-x GaS 2 has been studied under high pressure (up to 7 GPa) and at low temperature (50 K) using a diamond anvil high pressure cell for alloy concentrations x=1, 0.75, 0.5, 0.25 and 0. This has allowed us to determine the dependence of their zone-center phonon modes on both pressure and alloy concentration. The resultant phonon pressure coefficients are helpful in understanding the nature of the phonon modes in these chalcopyrites

  6. Modelling of chalcopyrite oxidation reactions in the Outokumpu flash smelting process

    Energy Technology Data Exchange (ETDEWEB)

    Ahokainen, T.; Jokilaakso, A. [Helsinki Univ. of Technology, Otaniemi (Finland)

    1996-12-31

    A mathematical model for simulating oxidation reactions of chalcopyrite particles together with momentum, heat and mass transfer between particle and gas phase in a flash smelting furnace reaction shaft is presented. In simulation, the equations governing the gas flow are solved numerically with a commercial fluid flow package, Phoenics. The particle phase is introduced into the gas flow by a Particle Source In Cell (PSIC) - technique, where a number of discrete particles is tracked in a gas flow and the relevant source terms for momentum, mass, and heat transfer are added to the gas phase equations. The gas phase equations used are elliptic in nature and the fluid turbulence is described by the (k-{epsilon}) -model. Thermal gas phase radiation is simulated with a six-flux radiation model. The chemical reactions of concentrate particles are assumed to happen at two sharp interfaces, and a shrinking core model is applied to describe the mass transfer of chemical species through the reaction product layer. In a molten state, the oxygen consumption is controlled by a film penetration concept. The reacting concentrate particles are a mixture of chalcopyrite and silica. Also a certain amount of pure inert silica is fed to the process as flux. In the simulations the calculation domain includes the concentrate burner and a cylindrical reaction shaft of an industrial scale flash smelting furnace. Some examples about the simulations carried out by the combustion model are presented. (author)

  7. Novel integration strategy for enhancing chalcopyrite bioleaching by Acidithiobacillus sp. in a 7-L fermenter.

    Science.gov (United States)

    Feng, Shoushuai; Yang, Hailin; Zhan, Xiao; Wang, Wu

    2014-06-01

    An integrated strategy (additional energy substrate-three stage pH control-fed batch) was firstly proposed for efficiently improving chalcopyrite bioleaching by Acidithiobacillus sp. in a 7-L fermenter. The strain adaptive-growing phase was greatly shortened from 8days into 4days with the supplement of additional 2g/L Fe(2+)+2g/L S(0). Jarosite passivation was effectively weakened basing on higher biomass via the three-stage pH-stat control (pH 1.3-1.0-0.7). The mineral substrate inhibition was attenuated by fed-batch fermentation. With the integrated strategy, the biochemical reaction was promoted and achieved a better balance. Meanwhile, the domination course of A. thiooxidans in the microbial community was shortened from 14days to 8days. As the results of integrated strategy, the final copper ion and productivity reached 89.1mg/L and 2.23mg/(Ld), respectively, which was improved by 52.8% compared to the uncontrolled batch bioleaching. The integrated strategy could be further exploited for industrial chalcopyrite bioleaching. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Electrochemical and spectroscopic study of interfacial interactions between chalcopyrite and typical flotation process reagents

    Science.gov (United States)

    Urbano, Gustavo; Lázaro, Isabel; Rodríguez, Israel; Reyes, Juan Luis; Larios, Roxana; Cruz, Roel

    2016-02-01

    Comparative voltammetry and differential double-layer capacitance studies were performed to evaluate interfacial interactions between chalcopyrite (CuFeS2) and n-isopropyl xanthate (X) in the presence of ammonium bisulfite/39wt% SO2 and caustic starch at different pH values. Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, contact angle measurements, and microflotation tests were used to establish the type and extent of xanthate adsorption as well as the species involved under different mineral surface conditions in this study. The results demonstrate that the species that favor a greater hydrophobicity of chalcopyrite are primarily CuX and S0, whereas oxides and hydroxides of Cu and Fe as well as an excess of starch decrease the hydrophobicity. A conditioning of the mineral surface with ammonium bisulfite/39wt% SO2 at pH 6 promotes the activation of surface and enhances the xanthate adsorption. However, this effect is diminished at pH ≥ 8, when an excess of starch is added during the preconditioning step.

  9. Modelling of chalcopyrite oxidation reactions in the Outokumpu flash smelting process

    Energy Technology Data Exchange (ETDEWEB)

    Ahokainen, T; Jokilaakso, A [Helsinki Univ. of Technology, Otaniemi (Finland)

    1997-12-31

    A mathematical model for simulating oxidation reactions of chalcopyrite particles together with momentum, heat and mass transfer between particle and gas phase in a flash smelting furnace reaction shaft is presented. In simulation, the equations governing the gas flow are solved numerically with a commercial fluid flow package, Phoenics. The particle phase is introduced into the gas flow by a Particle Source In Cell (PSIC) - technique, where a number of discrete particles is tracked in a gas flow and the relevant source terms for momentum, mass, and heat transfer are added to the gas phase equations. The gas phase equations used are elliptic in nature and the fluid turbulence is described by the (k-{epsilon}) -model. Thermal gas phase radiation is simulated with a six-flux radiation model. The chemical reactions of concentrate particles are assumed to happen at two sharp interfaces, and a shrinking core model is applied to describe the mass transfer of chemical species through the reaction product layer. In a molten state, the oxygen consumption is controlled by a film penetration concept. The reacting concentrate particles are a mixture of chalcopyrite and silica. Also a certain amount of pure inert silica is fed to the process as flux. In the simulations the calculation domain includes the concentrate burner and a cylindrical reaction shaft of an industrial scale flash smelting furnace. Some examples about the simulations carried out by the combustion model are presented. (author)

  10. Thermophilic archaeal community succession and function change associated with the leaching rate in bioleaching of chalcopyrite.

    Science.gov (United States)

    Zhu, Wei; Xia, Jin-lan; Yang, Yi; Nie, Zhen-yuan; Peng, An-an; Liu, Hong-chang; Qiu, Guan-zhou

    2013-04-01

    The community succession and function change of thermophilic archaea Acidianus brierleyi, Metallosphaera sedula, Acidianus manzaensis and Sulfolobus metallicus were studied by denaturing gradient gel electrophoresis (DGGE) analysis of amplifying 16S rRNA genes fragments and real-time qPCR analysis of amplifying sulfur-oxidizing soxB gene associated with chalcopyrite bioleaching rate at different temperatures and initial pH values. The analysis results of the community succession indicated that temperature and initial pH value had a significant effect on the consortium, and S. metallicus was most sensitive to the environmental change, A. brierleyi showed the best adaptability and sulfur oxidation ability and predominated in various leaching systems. Meanwhile, the leaching rate of chalcopyrite closely related to the consortium function embodied by soxB gene, which could prove a desirable way for revealing microbial sulfur oxidation difference and tracking the function change of the consortium, and for optimizing the leaching parameters and improving the recovery of valuable metals. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Selective Excitation of Window and Buffer Layers in Chalcopyrite Devices and Modules

    Energy Technology Data Exchange (ETDEWEB)

    Glynn, Stephen [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Repins, Ingrid L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Burst, James M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Beall, Carolyn L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bowers, Karen A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Mansfield, Lorelle M [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-02-02

    Window and buffer layers in chalcopyrite devices are well known to affect junctions, conduction, and photo-absorption properties of the device. Some of these layers, particularly 'buffers,' which are deposited directly on top of the absorber, exhibit metastable effects upon exposure to light. Thus, to understand device performance and/or metastability, it is sometimes desirable to selectively excite different layers in the device stack. Absorption characteristics of various window and buffer layers used in chalcopyrite devices are measured. These characteristics are compared with emission spectra of common and available light sources that might be used to optically excite such layers. Effects of the window and buffer absorption on device quantum efficiency and metastability are discussed. For the case of bath-deposited Zn(O,S) buffers, we conclude that this layer is not optically excited in research devices or modules. This provides a complimentary mechanism to the chemical differences that may cause long time constants (compared to devices with CdS buffers) associated with reaching a stable 'light-soaked' state.

  12. Presentation on mechanisms and applications of chalcopyrite and pyrite bioleaching in biohydrometallurgy - a presentation.

    Science.gov (United States)

    Tao, Huang; Dongwei, Li

    2014-12-01

    This review outlines classic and current research, scientific documents and research achievements in bioleaching, particularly in respect of the bioleaching of chalcopyrite and pyrite. The diversity and commonality of the microbial leaching process can be easily studied through comparing the bioleaching mechanism and the application of these two metal sulfides. The crystal, electronic and surface structures of chalcopyrite and pyrite are summarized in detail in this paper. It determines the specific and complicated interaction pathways, kinetics of the atmospheric/aqueous oxidation, and the control process of bioleaching of the minerals as the precondition. Bioleaching of metal sulfides is performed by a diverse group of microorganisms and microbial communities. The species of the bacteria which have a significant effect on leaching ores are miraculously diverse. The newly identified acidophilic microorganisms with unique characteristics for efficient bioleaching of sulfidic minerals are increasing sharply. The cell-to-cell communication mechanisms, which are still implicit, elusive and intangible at present day, have gradually become a research hotspot. The different mineralogy characteristics and the acid solubility of the metal sulfides (e.g., chalcopyrite and pyrite) cause two different dissolution pathways, the thiosulfate and the polysulfide pathways. The bioleaching mechanisms are categorized by contact (an electrostatic attachment) and noncontact (planktonic) process, with emphasis on the produce of extracellular polymeric substances and formation of biofilm on the surface of the metal sulfides in this paper. The division of the direct and indirect effect are not adopted due to the redox chain, the reduction of the ferric iron and oxidation of the ferrous iron. The molecular oxygen is reduced by the electrons extracted from the specific metal sulfide, via a redox chain forming a supercomplex spanning the periplasmic space and connecting both outer and inner

  13. Sulfobacillus thermosulfidooxidans strain Cutipay enhances chalcopyrite bioleaching under moderate thermophilic conditions in the presence of chloride ion.

    Science.gov (United States)

    Bobadilla-Fazzini, Roberto A; Cortés, Maria Paz; Maass, Alejandro; Parada, Pilar

    2014-12-01

    Currently more than 90% of the world's copper is obtained through sulfide mineral processing. Among the copper sulfides, chalcopyrite is the most abundant and therefore economically relevant. However, primary copper sulfide bioleaching is restricted due to high ionic strength raffinate solutions and particularly chloride coming from the dissolution of ores. In this work we describe the chalcopyrite bioleaching capacity of Sulfobacillus thermosulfidooxidans strain Cutipay (DSM 27601) previously described at the genomic level (Travisany et al. (2012) Draft genome sequence of the Sulfobacillus thermosulfidooxidans Cutipay strain, an indigenous bacterium isolated from a naturally extreme mining environment in Northern Chile. J Bacteriol 194:6327-6328). Bioleaching assays with the mixotrophic strain Cutipay showed a strong increase in copper recovery from chalcopyrite concentrate at 50°C in the presence of chloride ion, a relevant inhibitory element present in copper bioleaching processes. Compared to the abiotic control and a test with Sulfobacillus acidophilus DSM 10332, strain Cutipay showed an increase of 42 and 69% in copper recovery, respectively, demonstrating its high potential for chalcopyrite bioleaching. Moreover, a genomic comparison highlights the presence of the 2-Haloacid dehalogenase predicted-protein related to a potential new mechanism of chloride resistance in acidophiles. This novel and industrially applicable strain is under patent application CL 2013-03335.

  14. An insight into the mechanism of charge-transfer of hybrid polymer:ternary/quaternary chalcopyrite colloidal nanocrystals

    Directory of Open Access Journals (Sweden)

    Parul Chawla

    2014-08-01

    Full Text Available In this work, we have demonstrated the structural and optoelectronic properties of the surface of ternary/quaternary (CISe/CIGSe/CZTSe chalcopyrite nanocrystallites passivated by tri-n-octylphosphine-oxide (TOPO and tri-n-octylphosphine (TOP and compared their charge transfer characteristics in the respective polymer: chalcopyrite nanocomposites by dispersing them in poly(3-hexylthiophene polymer. It has been found that CZTSe nanocrystallites due to their high crystallinity and well-ordered 3-dimensional network in its pristine form exhibit a higher steric- and photo-stability, resistance against coagulation and homogeneity compared to the CISe and CIGSe counterparts. Moreover, CZTSe nanocrystallites display efficient photoluminescence quenching as evident from the high value of the Stern–Volmer quenching constant (KSV and eventually higher charge transfer efficiency in their respective polymer P3HT:CZTSe composites. We modelled the dependency of the charge transfer from the donor and the charge separation mechanism across the donor–acceptor interface from the extent of crystallinity of the chalcopyrite semiconductors (CISe/CIGSe/CZTSe. Quaternary CZTSe chalcopyrites with their high crystallinity and controlled morphology in conjunction with regioregular P3HT polymer is an attractive candidate for hybrid solar cells applications.

  15. An insight into the mechanism of charge-transfer of hybrid polymer:ternary/quaternary chalcopyrite colloidal nanocrystals.

    Science.gov (United States)

    Chawla, Parul; Singh, Son; Sharma, Shailesh Narain

    2014-01-01

    In this work, we have demonstrated the structural and optoelectronic properties of the surface of ternary/quaternary (CISe/CIGSe/CZTSe) chalcopyrite nanocrystallites passivated by tri-n-octylphosphine-oxide (TOPO) and tri-n-octylphosphine (TOP) and compared their charge transfer characteristics in the respective polymer: chalcopyrite nanocomposites by dispersing them in poly(3-hexylthiophene) polymer. It has been found that CZTSe nanocrystallites due to their high crystallinity and well-ordered 3-dimensional network in its pristine form exhibit a higher steric- and photo-stability, resistance against coagulation and homogeneity compared to the CISe and CIGSe counterparts. Moreover, CZTSe nanocrystallites display efficient photoluminescence quenching as evident from the high value of the Stern-Volmer quenching constant (K SV) and eventually higher charge transfer efficiency in their respective polymer P3HT:CZTSe composites. We modelled the dependency of the charge transfer from the donor and the charge separation mechanism across the donor-acceptor interface from the extent of crystallinity of the chalcopyrite semiconductors (CISe/CIGSe/CZTSe). Quaternary CZTSe chalcopyrites with their high crystallinity and controlled morphology in conjunction with regioregular P3HT polymer is an attractive candidate for hybrid solar cells applications.

  16. Examples of neutron diffraction texture analysis on one and the same chalcopyrite sample before and after experimental deformation

    International Nuclear Information System (INIS)

    Jansen, E.M.; Brokmeier, H.G.; Siemes, H.

    1994-01-01

    Natural chalcopyrite specimens from Mt. Isa, Australia were investigated by neutron diffraction texture analysis. The preferred orientation of the specimens consists of 3 main orientation components. After axial shortening at a temperature of 25 C the initial orientation components became weaker, a new component was detected. (orig.)

  17. Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

    Directory of Open Access Journals (Sweden)

    Wang Lan

    2016-01-01

    Full Text Available We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating and inkjet printing. Active area efficiencies of 12.8% and 12.2% have been achieved for In2S3-buffered solar cells respectively, matching the performance of CdS-buffered cells prepared with the same batch of absorbers.

  18. Saline-water bioleaching of chalcopyrite with thermophilic, iron(II)- and sulfur-oxidizing microorganisms.

    Science.gov (United States)

    Watling, Helen R; Collinson, David M; Corbett, Melissa K; Shiers, Denis W; Kaksonen, Anna H; Watkin, Elizabeth L J

    2016-09-01

    The application of thermoacidophiles for chalcopyrite (CuFeS2) bioleaching in hot, acidic, saline solution was investigated as a possible process route for rapid Cu extraction. The study comprised a discussion of protective mechanisms employed for the survival and/or adaptation of thermoacidophiles to osmotic stress, a compilation of chloride tolerances for three genera of thermoacidophiles applied in bioleaching and an experimental study of the activities of three species in a saline bioleaching system. The data showed that the oxidation rates of iron(II) and reduced inorganic sulfur compounds (tetrathionate) were reduced in the presence of chloride levels well below chloride concentrations in seawater, limiting the applicability of these microorganisms in the bioleaching of CuFeS2 in saline water. Copyright © 2016. Published by Elsevier Masson SAS.

  19. Simulation of Bioleaching Heat Effects for Enhancement of Copper Recovery from Sarcheshmeh Chalcopyrite

    Science.gov (United States)

    Mahmoudian, Ali Reza; Sadrnezhaad, S. K.; Manafi, Zahra

    2014-08-01

    A heat-transfer model was formulated to determine the distribution of temperature within a bioheap of chalcopyrite of Sarcheshmeh copper mine. Bioleaching employs mixed mesophilic and thermophilic microbes for Cu extraction. Thermophiles are better than mesophiles to dissolve CuFeS2. The solution irrigation and aeration rates were taken into account as the main operational factors. The model was validated by comparing the temperature profiles of test columns with those of bioheap. The model was used to find the optimal ratio of irrigation to aeration. It was found that when the solution was fed at a flow rate of 5 kg/m2 h and air was blown at a flow rate of 7.5 kg/m2 h, the transition from a mesophilic to thermophilic state inside the heap was possible. In this situation, the maximum temperature rise inside the heap was about 332 K (59 °C) after 60 days.

  20. Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

    Science.gov (United States)

    Wang, Lan; Lin, Xianzhong; Ennaoui, Ahmed; Wolf, Christian; Lux-Steiner, Martha Ch.; Klenk, Reiner

    2016-02-01

    We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating and inkjet printing. Active area efficiencies of 12.8% and 12.2% have been achieved for In2S3-buffered solar cells respectively, matching the performance of CdS-buffered cells prepared with the same batch of absorbers.

  1. Assessment of the flotability of chalcopyrite, molybdenite and pyrite using biosolids and their main components as collectors for greening the froth flotation of copper sulphide ores.

    OpenAIRE

    Sobarzo, Francisco; Herrera Urbina, Ronaldo; Higueras Higueras, Pablo Leon; Sáez Navarrete, César; Godoy Faúndez, Alex; Reyes Bozo, Lorenzo; Vásquez Bestagno, Jorge

    2014-01-01

    Biosolids and representative compounds of their main components ? humic acids, sugars, and proteins ? have been tested as possible environment-friendly collectors and frothers for the flotation of copper sulphide ores. The floatability of chalcopyrite and molybdenite ? both valuable sulphide minerals present in these ores ? as well as non-valuable pyrite was assessed through Hallimond tube flotation tests. Humic acids exhibit similar collector ability for chalcopyrite and molybdenite as that ...

  2. Fabrication of dye sensitized solar cell using Cr doped Cu-Zn-Se type chalcopyrite thin film

    Energy Technology Data Exchange (ETDEWEB)

    Joseph, D. Paul; Venkateswaran, C. [Materials Science Centre, Department of Nuclear Physics, University of Madras, Guindy Campus, Chennai-600 025 (India); Ganesan, S.; Suthanthiraraj, S. Austin; Maruthamuthu, P. [Department of Energy, University of Madras, Guindy Campus, Chennai 600 025 (India); Kovendhan, M. [Department of Physics, Presidency College, Chennai 600 005 (India)

    2011-09-15

    Chalcopyrites are a versatile class of semiconductors known for their potential in photovoltaic applications. Considering the well established CuInSe{sub 2} as a prototype system, a new compound of the chalcopyrite type, Cu{sub 1-x}Zn{sub 1-y}Se{sub 2-{delta}}, by replacing In with Zn, has been prepared (both undoped and 2% Cr doped) by the metallurgical method. Thin films have been deposited by the thermal evaporation technique using the stabilized polycrystalline compounds as charge. Structural, compositional, morphological, and optical properties of the films are analyzed and reported. Use of these films as electrodes in dye sensitized solar cell (DSSC) is demonstrated. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Influence of temperature on the fixation and penetration of silver during the chalcopyrite leaching using moderate thermophilic microorganisms

    International Nuclear Information System (INIS)

    Cancho, L.; Blazquez, M. L.; Munoz, J. A.; Gonzalez, F.; Ballester, A.

    2004-01-01

    Bio leaching of chalcopyrite using mesophilic microorganisms considerable improves in the presence of silver. However, the studies carried out with moderate thermophilic microorganisms do not show a significant improvement with regard to the use of mesophilic bacteria. The main objective of the present work has been to study the silver fixation on chalcopyrite ar 35 and 45 degree centigree and its influence on the microbiological attack. Different observations using SEM, EDS microanalysis and concentration profiles using electron microprobe have been carried out. The study of the different samples showed that silver fixation was more favourable at 35 degree centigree than at 45 degree centigree. In addition, bacterial action improved silver penetration through attack cracks. (Author)

  4. Community dynamics of attached and free cells and the effects of attached cells on chalcopyrite bioleaching by Acidithiobacillus sp.

    Science.gov (United States)

    Yang, Hailin; Feng, Shoushuai; Xin, Yu; Wang, Wu

    2014-02-01

    The community dynamics of attached and free cells of Acidithiobacillus sp. were investigated and compared during chalcopyrite bioleaching process. In the mixed strains system, Acidithiobacillus ferrooxidans was the dominant species at the early stage while Acidithiobacillus thiooxidans owned competitive advantage from the middle stage to the end of bioprocess. Meanwhile, compared to A. ferrooxidans, more significant effects of attached cells on free biomass with A. thiooxidans were shown in either the pure or mixed strains systems. Moreover, the effects of attached cells on key chemical parameters were also studied in different adsorption-deficient systems. Consistently, the greatest reduction of key chemical ion was shown with A. thiooxidans and the loss of bioleaching efficiency was high to 50.5%. These results all demonstrated the bioleaching function of attached cells was more efficient than the free cells, especially with A. thiooxidans. These notable results would help us to further understand the chalcopyrite bioleaching. Copyright © 2013 Elsevier Ltd. All rights reserved.

  5. Effect of pH values on the extracellular polysaccharide secreted by Acidithiobacillus ferrooxidans during chalcopyrite bioleaching

    Science.gov (United States)

    Yu, Run-lan; Liu, Jing; Tan, Jian-xi; Zeng, Wei-min; Shi, Li-juan; Gu, Guo-hua; Qin, Wen-qing; Qiu, Guan-zhou

    2014-04-01

    The pH value plays an important role in the bioleaching of sulphide minerals. The effect of pH values on the extracellular polysaccharide secreted by Acidithiobacillus ferrooxidans was investigated in different phases of bacterial growth during chalcopyrite bioleaching. It is found that extracellular polysaccharide secretion from the cells attached to chalcopyrite is more efficiently than that of the free cells in the bioleaching solution. Three factors, pH values, the concentration of soluble metal ions, and the bacterial growth and metabolism, affect extracellular polysaccharide secretion in the free cells, and are related to the bacterial growth phase. Extracellular polysaccharide secretion from the attached cells is mainly dependent on the pH value of the bacterial culture.

  6. The Influencing Mechanisms of Sodium Hexametaphosphate on Chalcopyrite Flotation in the Presence of MgCl2 and CaCl2

    Directory of Open Access Journals (Sweden)

    Wanqing Li

    2018-04-01

    Full Text Available Sea water has been used in flotation plants, showing a promising way to save fresh water usage. Previous studies indicated that divalent salts in sea water played negative roles in chalcopyrite flotation, but not much work have been conducted to understand the eliminating mechanisms. This study systematically investigated the effects of divalent cations of Ca2+ and Mg2+ on natural flotability of chalcopyrite in the absence of collectors and frothers. The reduced recovery was mainly due to the adsorption of Mg and Ca hydroxyl complexes and precipitation on chalcopyrite surfaces, giving rise to a less hydrophobic surface. The addition of sodium hexametaphosphate (SHMP, however, significantly improved chalcopyrite recovery. Species calculation, contact angle, zeta potential, FTIR and XPS analyses were conducted to understand the influencing mechanisms of divalent ions and the beneficial effects of SHMP on chalcopyrite recovery. The primary mechanism was that SHMP prevented the adsorption of positively charged Mg and Ca compounds or precipitation with hydrophilic properties such as Mg(OH2 on chalcopyrite surfaces, confirmed by the Derjguin-Landau-Verwey-Overbeek (DLVO theory. Secondly, SHMP reacted with Mg2+ and Ca2+ to form dissolvable complexes, thereby declining the formation of insoluble Mg2+ and Ca2+ compounds or precipitation.

  7. Insights to the effects of free cells on community structure of attached cells and chalcopyrite bioleaching during different stages.

    Science.gov (United States)

    Feng, Shoushuai; Yang, Hailin; Wang, Wu

    2016-01-01

    The effects of free cells on community structure of attached cells and chalcopyrite bioleaching by Acidithiobacillus sp. during different stages were investigated. The attached cells of Acidithiobacillus thiooxidans owned the community advantage from 14thd to the end of bioprocess in the normal system. The community structure of attached cells was greatly influenced in the free cells-deficient systems. Compared to A. thiooxidans, the attached cells community of Acidithiobacillus ferrooxidans had a higher dependence on its free cells. Meanwhile, the analysis of key biochemical parameters revealed that the effects of free cells on chalcopyrite bioleaching in different stages were diverse, ranging from 32.8% to 64.3%. The bioleaching contribution of free cells of A. ferrooxidans in the stationary stage (8-14thd) was higher than those of A. thiooxidans, while the situation was gradually reversed in the jarosite passivation inhibited stage (26-40thd). These results may be useful in guiding chalcopyrite bioleaching. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Effects of pyrite and sphalerite on population compositions, dynamics and copper extraction efficiency in chalcopyrite bioleaching process.

    Science.gov (United States)

    Xiao, Yunhua; Liu, Xueduan; Dong, Weiling; Liang, Yili; Niu, Jiaojiao; Gu, Yabing; Ma, Liyuan; Hao, Xiaodong; Zhang, Xian; Xu, Zhen; Yin, Huaqun

    2017-07-01

    This study used an artificial microbial community with four known moderately thermophilic acidophiles (three bacteria including Acidithiobacillus caldus S1, Sulfobacillus thermosulfidooxidans ST and Leptospirillum ferriphilum YSK, and one archaea, Ferroplasma thermophilum L1) to explore the variation of microbial community structure, composition, dynamics and function (e.g., copper extraction efficiency) in chalcopyrite bioleaching (C) systems with additions of pyrite (CP) or sphalerite (CS). The community compositions and dynamics in the solution and on the ore surface were investigated by real-time quantitative PCR (qPCR). The results showed that the addition of pyrite or sphalerite changed the microbial community composition and dynamics dramatically during the chalcopyrite bioleaching process. For example, A. caldus (above 60%) was the dominant species at the initial stage in three groups, and at the middle stage, still dominated C group (above 70%), but it was replaced by L. ferriphilum (above 60%) in CP and CS groups; at the final stage, L. ferriphilum dominated C group, while F. thermophilum dominated CP group on the ore surface. Furthermore, the additions of pyrite or sphalerite both made the increase of redox potential (ORP) and the concentrations of Fe 3+ and H + , which would affect the microbial community compositions and copper extraction efficiency. Additionally, pyrite could enhance copper extraction efficiency (e.g., improving around 13.2% on day 6) during chalcopyrite bioleaching; on the contrary, sphalerite restrained it.

  9. Surface characterization by X-ray photoelectron spectroscopy and cyclic voltammetry of products formed during the potentiostatic reduction of chalcopyrite

    International Nuclear Information System (INIS)

    Nava, Dora; Gonzalez, Ignacio; Leinen, Dietmar; Ramos-Barrado, Jose R.

    2008-01-01

    Surface characterization of the transient products that precede chalcocite formation during chalcopyrite reduction was carried out. The experimental strategy employed in the present work consisted of the application of different potential pulses (fixed energetic conditions) on the surface of chalcopyrite electrodes in 1.7 M H 2 SO 4 . The chemical products formed at different potential pulses were characterized by cyclic voltammetry (CV) and XPS. Each electrogenerated species presented a specific voltammetric behavior and an XPS spectrum, in which the values of principal photoelectronic peak bond energies for Cu 2p 3/2 , Fe 2p 3/2 and S 2p 3/2 and the atomic concentrations were considered. Several potential intervals could be identified: in 0.115 ≥ E cat ≥ -0.085 V vs. SHE, an intermediate copper sulfide is formed whose composition is between those of chalcopyrite and bornite, such as talnakhite. The reduction of this product occurs slowly, giving bornite at potentials less than -0.085 V. In the applied potential region -0.085 ≥ E cat > -0.185 V, the bornite gradually decomposes causing the incomplete conversion to chalcocite. In the potential interval -0.185 > E cat ≥ -0.285 V, energetic conditions are large enough to allow the immediate decomposition of bornite, forming chalcocite in a more quantitative manner

  10. The community dynamics of major bioleaching microorganisms during chalcopyrite leaching under the effect of organics.

    Science.gov (United States)

    Li, Qihou; Tian, Ye; Fu, Xian; Yin, Huaqun; Zhou, Zhijun; Liang, Yiting; Qiu, Guanzhou; Liu, Jie; Liu, Hongwei; Liang, Yili; Shen, Li; Cong, Jing; Liu, Xueduan

    2011-08-01

    To determine the effect of organics (yeast extract) on microbial community during chalcopyrite bioleaching at different temperature, real-time polymerase chain reaction (PCR) was employed to analyze community dynamics of major bacteria applied in bioleaching. The results showed that yeast extract exerted great impact on microbial community, and therefore influencing bioleaching rate. To be specific, yeast extract was adverse to this bioleaching process at 30°C due to decreased proportion of important chemolithotrophs such as Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans. However, yeast extract could promote bioleaching rate at 40°C on account of the increased number and enhanced work of Ferroplasma thermophilum, a kind of facultative bacteria. Similarly, bioleaching rate was enhanced under the effect of yeast extract at 50°C owing to the work of Acidianus brierleyi. At 60°C, bioleaching rate was close to 100% and temperature was the dominant factor determining bioleaching rate. Interestingly, the existence of yeast extract greatly enhanced the relative competitiveness of Ferroplasma thermophilum in this complex bioleaching microbial community.

  11. Acidithiobacillus thiooxidans secretome containing a newly described lipoprotein Licanantase enhances chalcopyrite bioleaching rate

    Science.gov (United States)

    Bobadilla Fazzini, Roberto A.; Levican, Gloria

    2010-01-01

    The nature of the mineral–bacteria interphase where electron and mass transfer processes occur is a key element of the bioleaching processes of sulfide minerals. This interphase is composed of proteins, metabolites, and other compounds embedded in extracellular polymeric substances mainly consisting of sugars and lipids (Gehrke et al., Appl Environ Microbiol 64(7):2743–2747, 1998). On this respect, despite Acidithiobacilli—a ubiquitous bacterial genera in bioleaching processes (Rawlings, Microb Cell Fact 4(1):13, 2005)—has long been recognized as secreting bacteria (Jones and Starkey, J Bacteriol 82:788–789, 1961; Schaeffer and Umbreit, J Bacteriol 85:492–493, 1963), few studies have been carried out in order to clarify the nature and the role of the secreted protein component: the secretome. This work characterizes for the first time the sulfur (meta)secretome of Acidithiobacillus thiooxidans strain DSM 17318 in pure and mixed cultures with Acidithiobacillus ferrooxidans DSM 16786, identifying the major component of these secreted fractions as a single lipoprotein named here as Licanantase. Bioleaching assays with the addition of Licanantase-enriched concentrated secretome fractions show that this newly found lipoprotein as an active protein additive exerts an increasing effect on chalcopyrite bioleaching rate. Electronic supplementary material The online version of this article (doi:10.1007/s00253-010-3063-8) contains supplementary material, which is available to authorized users. PMID:21191788

  12. Dissolution characteristics of sericite in chalcopyrite bioleaching and its effect on copper extraction

    Science.gov (United States)

    Dong, Ying-bo; Li, Hao; Lin, Hai; Zhang, Yuan

    2017-04-01

    The effects of sericite particle size, rotation speed, and leaching temperature on sericite dissolution and copper extraction in a chalcopyrite bioleaching system were examined. Finer particles, appropriate temperature and rotation speed for Acidithiobacillus ferrooxidans resulted in a higher Al3+ dissolution concentration. The Al3+ dissolution concentration reached its highest concentration of 38.66 mg/L after 48-d leaching when the sericite particle size, temperature, and rotation speed were -43 μm, 30°C, and 160 r/min, respectively. Meanwhile, the sericite particle size, rotation speed, and temperature can affect copper extraction. The copper extraction rate is higher when the sericite particle size is finer. An appropriately high temperature is favorable for copper leaching. The dissolution of sericite fitted the shrinking core model, 1-(2/3) α-(1- α)2/3 = k 1 t, which indicates that internal diffusion is the decision step controlling the overall reaction rate in the leaching process. Scanning electron microscopy analysis showed small precipitates covered on the surface of sericite after leaching, which increased the diffusion resistance of the leaching solution and dissolved ions.

  13. A stochastic model of solid state thin film deposition: Application to chalcopyrite growth

    Directory of Open Access Journals (Sweden)

    Robert J. Lovelett

    2016-04-01

    Full Text Available Developing high fidelity quantitative models of solid state reaction systems can be challenging, especially in deposition systems where, in addition to the multiple competing processes occurring simultaneously, the solid interacts with its atmosphere. In this work, we develop a model for the growth of a thin solid film where species from the atmosphere adsorb, diffuse, and react with the film. The model is mesoscale and describes an entire film with thickness on the order of microns. Because it is stochastic, the model allows us to examine inhomogeneities and agglomerations that would be impossible to characterize with deterministic methods. We demonstrate the modeling approach with the example of chalcopyrite Cu(InGa(SeS2 thin film growth via precursor reaction, which is a common industrial method for fabricating thin film photovoltaic modules. The model is used to understand how and why through-film variation in the composition of Cu(InGa(SeS2 thin films arises and persists. We believe that the model will be valuable as an effective quantitative description of many other materials systems used in semiconductors, energy storage, and other fast-growing industries.

  14. Structural, electronic, linear, and nonlinear optical properties of ZnCdTe{sub 2} chalcopyrite

    Energy Technology Data Exchange (ETDEWEB)

    Ouahrani, Tarik [Laboratoire de Physique Theorique, Universite de Tlemcen, B.P. 230, Tlemcen 13000 (Algeria); Reshak, Ali H. [Institute of Physical Biology, South Bohemia University, Nove Hrady 37333 (Czech Republic); School of Microelectronic Engineering, University of Malaysia Perlis (UniMAP), Block A, Kompleks Pusat Pengajian, 02600 Arau Jejawi, Perlis (Malaysia); Khenata, R. [Laboratoire de Physique Quantique et de Modelisation Mathematique, Universite de Mascara, Mascara 29000 (Algeria); Department of Physics and Astronomy, Faculty of Science, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia); Baltache, H.; Amrani, B. [Laboratoire de Physique Quantique et de Modelisation Mathematique, Universite de Mascara, Mascara 29000 (Algeria); Bouhemadou, A. [Department of Physics and Astronomy, Faculty of Science, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia); Faculty of Sciences, Department of Physics, University of Setif, Setif 19000 (Algeria)

    2011-03-15

    We report results of first-principles density functional calculations using the full-potential linearized augmented plane wave method. The generalized gradient approximation (GGA) and the Engel-Vosko-GGA (EV-GGA) formalism were used for the exchange-correlation energy to calculate the structural, electronic, linear, and nonlinear optical properties of the chalcopyrite ZnCdTe{sub 2} compound. The valence band maximum and the conduction band minimum are located at the {gamma}-point, resulting in a direct band gap of about 0.71 eV for GGA and 1.29 eV for EV-GGA. The results of bulk properties, such as lattice parameters (a, c, and u), bulk modulus B, and its pressure derivative B' are evaluated. The optical properties of this compound, namely the real and the imaginary parts of the dielectric function, reflectivity, and refractive index, show a considerable anisotropy as a consequence ZnCdTe{sub 2} posseses a strong birefringence. In addition, the extinction coefficient, the electron energy loss function, and the nonlinear susceptibility are calculated and their spectra are analyzed. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  15. An optimized In–CuGa metallic precursors for chalcopyrite thin films

    Energy Technology Data Exchange (ETDEWEB)

    Han, Jun-feng, E-mail: junfeng.han@cnrs-imn.fr [Institut des Matériaux Jean Rouxel (IMN), Université de Nantes, UMR CNRS 6502, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France); Department of Physics, Peking University, Beijing 100871 (China); Liao, Cheng [Department of Physics, Peking University, Beijing 100871 (China); Chengdu Green Energy and Green Manufacturing Technology R and D Center, Chengdu, Sichuan Province 601207 (China); Jiang, Tao; Xie, Hua-mu; Zhao, Kui [Department of Physics, Peking University, Beijing 100871 (China); Besland, M.-P. [Institut des Matériaux Jean Rouxel (IMN), Université de Nantes, UMR CNRS 6502, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France)

    2013-10-31

    We report a study of CuGa–In metallic precursors for chalcopyrite thin film. CuGa and In thin films were prepared by DC sputtering at room temperature. Due to low melting point of indium, the sputtering power on indium target was optimized. Then, CuGa and In multilayers were annealed at low temperature. At 120 °C, the annealing treatment could enhance diffusion and alloying of CuGa and In layers; however, at 160 °C, it caused a cohesion and crystalline of indium from the alloy which consequently formed irregular nodules on the film surface. The precursors were selenized to form copper indium gallium selenide (CIGS) thin films. The morphological and structural properties were investigated by scanning electron microscopy, X-ray diffraction and Raman spectra. The relationships between metallic precursors and CIGS films were discussed in the paper. A smooth precursor layer was the key factor to obtain a homogeneous and compact CIGS film. - Highlights: • An optimized sputtered indium film • An optimized alloying process of metallic precursor • An observation of nodules forming on the indium film and precursor surface • An observation of cauliflower structure in copper indium gallium selenide film • The relationship between precursor and CIGS film surface morphology.

  16. Electronic structure of semiconductor thin films (chalcopyrites) as absorbermaterials for thin film solar cells

    International Nuclear Information System (INIS)

    Lehmann, Carsten

    2007-01-01

    The objective of this work was to determine for the first time the band structure of CuInS 2 . For this purpose a new GSMBE process with TBDS as sulphur precursor was established to prevent the use of elemental sulphur in an UHV system. Additionally to the deposited films a cleave surface was prepared. The samples were characterized in situ by XPS/UPS and LEED. XRD and SEM were used for further ex situ investigations. The band structure was determined by ARUPS using synchrotron light. CuInS(001) and CuInS 2 (112) were deposited on Si and GaAs. The deposition of CuInS 2 on GaAs showed a strong dependence on the existing surface reconstruction. A 2 x 1 reconstruction of GaAs(001) yielded CuInS 2 (001) films featuring terraces. A deposition on 2 x 2 reconstructed GaAs(111)A surfaces led to a facetted CuInS 2 surface. On sulphur-passivated non-reconstructed GaAs(111)B a deposition of chalcopyrite ordered CuInS 2 free of facets was possible. On the surface of Cu-rich CuInS 2 films CuS crystallites formed. This yields ARUPS spectra showing the electronic stucture of CuInS 2 superimposed by non-dispergative states of the polycrystalline CuS segregations. The effective hole masses were derived from the k vertical stroke vertical stroke measurements. Finally the results of this work showed that the use of a (111) substrate leads to domain formation of the deposited CuInS 2 (112) films. Thus ARUPS spectra of such films show a superposition of the band structures along different directions. (orig.)

  17. ANALYSIS OF A DATA BASE OF CHALCOPYRITE SEMICONDUCTORS IN 2 AND 3 DIMENSIONS

    Directory of Open Access Journals (Sweden)

    A. M. Ferouani

    2015-07-01

    Full Text Available  The analysis of the data is currently, in the statisticians, the object of a true phenomenon of mode, characterized at the same time by the passion and the rejection. ¶To determine the characteristics of a whole of data is obviously not an end in itself, but this lapse of memory is unfortunate because the type of data available always influences the direction of research. ¶The factorial analysis in normalized principal components (PCA, is particularly adapted to the reduction of tables of measurements, where one generally works on a matrix of correlation between characters. ¶In this article we will report our results of analysis into 2 and 3 dimensions of the molecular weight and energy of plasmon of semiconductor chalcopyrites by using what one call the datamining materials. ¶All information was presented in the tables envisaged by an ACP method of the semiconductors étudiés. L' analyzes factorial substitutes for primitive measurements of new variables or factors (which are linear combinations of the primitive variables with the help of which it is thus possible to optimize the visualization of the data in a restricted number of figures.Large at the modo we present, the results related to the development of ¶new approaches of Datamining, Analysis in principal components (ACP, of the data-processing techniques which were applied to semiconductors and ¶combined with metals to predict new materials or ultra stable coatings.¶ ¶       

  18. Microbial leaching of low grade copper ores

    International Nuclear Information System (INIS)

    Rauf, A.; Ashfaq, M.

    1991-01-01

    Biotechnology is regarded as one of the most promising and revolutionary solution to various problems which are generally faced in the extraction of metals from their ores such as high energy, capital costs and environmental pollution. The paper deals with the study of low grade copper ores for their beneficiation and extraction of copper. The ores used were chalcopyrite and oxidized copper ores. Microorganisms play a vital role in the solubilization of valuable contents from ores such as copper and other metals. Studies have been conducted on the indigenous copper ores by using thiobacillus ferro oxidans and thiobacillus thio oxidans. For comparison purpose some experiments have also been conducted by chemical leaching. The results of bacterial leaching are encouraging. (author)

  19. A High-Yield Synthesis of Chalcopyrite CuInS2 Nanoparticles with Exceptional Size Control

    Directory of Open Access Journals (Sweden)

    Chivin Sun

    2009-01-01

    Full Text Available We report high-yield and efficient size-controlled syntheses of Chalcopyrite CuInS2 nanoparticles by decomposing molecular single source precursors (SSPs via microwave irradiation in the presence of 1,2-ethanedithiol at reaction temperatures as low as 100°C and times as short as 30 minutes. The nanoparticles sizes were 1.8 nm to 10.8 nm as reaction temperatures were varied from 100°C to 200°C with the bandgaps from 2.71 eV to 1.28 eV with good size control and high yields (64%–95%. The resulting nanoparticles were analyzed by XRD, UV-Vis, ICP-OES, XPS, SEM, EDS, and HRTEM. Titration studies by 1H NMR using SSP 1 with 1,2-ethanedithiol and benzyl mercaptan were conducted to elucidate the formation of Chalcopyrite CuInS2 nanoparticles.

  20. Co-culture microorganisms with different initial proportions reveal the mechanism of chalcopyrite bioleaching coupling with microbial community succession.

    Science.gov (United States)

    Ma, Liyuan; Wang, Xingjie; Feng, Xue; Liang, Yili; Xiao, Yunhua; Hao, Xiaodong; Yin, Huaqun; Liu, Hongwei; Liu, Xueduan

    2017-01-01

    The effect of co-culture microorganisms with different initial proportions on chalcopyrite bioleaching was investigated. Communities were rebuilt by six typical strains isolated from the same habitat. The results indicated, by community with more sulfur oxidizers at both 30 and 40°C, the final copper extraction rate was 19.8% and 6.5% higher, respectively, than that with more ferrous oxidizers. The variations of pH, redox potential, ferrous and copper ions in leachate also provided evidences that community with more sulfur oxidizers was more efficient. Community succession of free and attached cells revealed that initial proportions played decisive roles on community dynamics at 30°C, while communities shared similar structures, not relevant to initial proportions at 40°C. X-ray diffraction analysis confirmed different microbial functions on mineral surface. A mechanism model for chalcopyrite bioleaching was established coupling with community succession. This will provide theoretical basis for reconstructing an efficient community in industrial application. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. A comparative study of solution-processed low- and high-band-gap chalcopyrite thin-film solar cells

    International Nuclear Information System (INIS)

    Park, Se Jin; Moon, Sung Hwan; Min, Byoung Koun; Cho, Yunae; Kim, Ji Eun; Kim, Dong-Wook; Lee, Doh-Kwon; Gwak, Jihye; Kim, Jihyun

    2014-01-01

    Low-cost and printable chalcopyrite thin-film solar cells were fabricated by a precursor solution-based coating method with a multi-step heat-treatment process (oxidation, sulfurization, and selenization). The high-band-gap (1.57 eV) Cu(In x Ga 1−x )S 2 (CIGS) solar cell showed a high open-circuit voltage of 787 mV, whereas the low-band-gap (1.12 eV) Cu(In x Ga 1−x )(S 1−y Se y ) 2 (CIGSSe) cell exhibited a high short-circuit current density of 32.6 mA cm −2 . The energy conversion efficiencies were 8.28% for CIGS and 8.81% for CIGSSe under standard irradiation conditions. Despite similar efficiencies, the two samples showed notable differences in grain size, surface morphology, and interfacial properties. Low-temperature transport and admittance characteristics of the samples clearly revealed how their structural differences influenced their photovoltaic and electrical properties. Such analyses provide insight into the enhanced solar cell performance of the solution-processed chalcopyrite thin films. (paper)

  2. Spray Chemical Vapor Deposition of Single-Source Precursors for Chalcopyrite I-III-VI2 Thin-Film Materials

    Science.gov (United States)

    Hepp, Aloysius F.; Banger, Kulbinder K.; Jin, Michael H.-C.; Harris, Jerry D.; McNatt, Jeremiah S.; Dickman, John E.

    2008-01-01

    Thin-film solar cells on flexible, lightweight, space-qualified substrates provide an attractive approach to fabricating solar arrays with high mass-specific power. A polycrystalline chalcopyrite absorber layer is among the new generation of photovoltaic device technologies for thin film solar cells. At NASA Glenn Research Center we have focused on the development of new single-source precursors (SSPs) for deposition of semiconducting chalcopyrite materials onto lightweight, flexible substrates. We describe the syntheses and thermal modulation of SSPs via molecular engineering. Copper indium disulfide and related thin-film materials were deposited via aerosol-assisted chemical vapor deposition using SSPs. Processing and post-processing parameters were varied in order to modify morphology, stoichiometry, crystallography, electrical properties, and optical properties to optimize device quality. Growth at atmospheric pressure in a horizontal hotwall reactor at 395 C yielded the best device films. Placing the susceptor closer to the evaporation zone and flowing a more precursor-rich carrier gas through the reactor yielded shinier-, smoother-, and denser-looking films. Growth of (112)-oriented films yielded more Cu-rich films with fewer secondary phases than growth of (204)/(220)-oriented films. Post-deposition sulfur-vapor annealing enhanced stoichiometry and crystallinity of the films. Photoluminescence studies revealed four major emission bands and a broad band associated with deep defects. The highest device efficiency for an aerosol-assisted chemical vapor deposited cell was one percent.

  3. Suppression of antiferromagnetic interactions through Cu vacancies in Mn-substituted CuInSe2 chalcopyrites

    International Nuclear Information System (INIS)

    Yao Jinlei; Brunetta, Carl D; Aitken, Jennifer A

    2012-01-01

    Stoichiometric and Cu-poor Cu 0.95-x Mn 0.05 InSe 2 (x = 0-0.20) compounds were synthesized by high-temperature, solid-state reactions. The presence of copper vacancies is revealed by Rietveld refinements of combined neutron and x-ray powder diffraction data. The antiferromagnetic interaction is depressed by the copper deficiency, which may be explained as the competition between the antiferromagnetic Mn-Se-eMn superexchange interaction and the hole-mediated ferromagnetic exchange induced by the copper vacancy. The introduction of copper vacancies is proposed to be a viable route to impart carrier-mediated ferromagnetic exchange in the chalcopyrite-based dilute magnetic semiconductors. (paper)

  4. Thermoelectricity Generation and Electron-Magnon Scattering in a Natural Chalcopyrite Mineral from a Deep-Sea Hydrothermal Vent.

    Science.gov (United States)

    Ang, Ran; Khan, Atta Ullah; Tsujii, Naohito; Takai, Ken; Nakamura, Ryuhei; Mori, Takao

    2015-10-26

    Current high-performance thermoelectric materials require elaborate doping and synthesis procedures, particularly in regard to the artificial structure, and the underlying thermoelectric mechanisms are still poorly understood. Here, we report that a natural chalcopyrite mineral, Cu1+x Fe1-x S2 , obtained from a deep-sea hydrothermal vent can directly generate thermoelectricity. The resistivity displayed an excellent semiconducting character, and a large thermoelectric power and high power factor were found in the low x region. Notably, electron-magnon scattering and a large effective mass was detected in this region, thus suggesting that the strong coupling of doped carriers and antiferromagnetic spins resulted in the natural enhancement of thermoelectric properties during mineralization reactions. The present findings demonstrate the feasibility of thermoelectric energy generation and electron/hole carrier modulation with natural materials that are abundant in the Earth's crust. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Defect formation energies and homogeneity ranges of rock salt-, pyrite-, chalcopyrite- and molybdenite-type compound semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Fiechter, S. [Hahn-Meitner-Institut, Glienicker Strasse 100, Berlin D-14109 (Germany)

    2004-07-01

    Employing the generalisation of Van Vechten's cavity model, formation energies of neutral point defects in pyrites (FeS{sub 2}, RuS{sub 2}), chalcopyrites (II-IV-V{sub 2} and I-III-VI{sub 2}) as well as molybdenites (MoS{sub 2}, WS{sub 2}) have been estimated. As input parameters the fundamental band gaps, work functions, electron affinities, surface energies, coordination numbers, covalent or ionic radii and unit cell parameters were used. The values calculated for tetrahedrally and octahedrally coordinated compounds agreed well with measured values. The data obtained can be used to calculate point defect concentrations and homogeneity ranges as a function of partial pressure and temperature. Introducing charged vacancies, the conductivity type can be predicted.

  6. Structural and elastic properties of defect chalcopyrite HgGa{sub 2}S{sub 4} under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Gomis, O., E-mail: osgohi@fis.upv.es [Centro de Tecnologías Físicas: Acústica, Materiales y Astrofísica, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); Santamaría-Pérez, D. [Departamento de Física Aplicada-ICMUV, MALTA Consolider Team, Universitat de València, Edificio de Investigación, C/Dr. Moliner 50, Burjassot, 46100 València (Spain); Departamento de Química Física I, Universidad Complutense de Madrid, MALTA Consolider Team, Avenida Complutense s/n, 28040 Madrid (Spain); Vilaplana, R.; Luna, R. [Centro de Tecnologías Físicas: Acústica, Materiales y Astrofísica, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); Sans, J.A.; Manjón, F.J. [Instituto de Diseño para la Fabricación y Producción Automatizada, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); Errandonea, D. [Departamento de Física Aplicada-ICMUV, MALTA Consolider Team, Universitat de València, Edificio de Investigación, C/Dr. Moliner 50, Burjassot, 46100 València (Spain); and others

    2014-01-15

    Highlights: • Single crystals of HgGa{sub 2}S{sub 4} with defect-chalcopyrite (DC) structure were synthesized. • High-pressure X-ray diffraction in DC-HgGa{sub 2}S{sub 4} was performed. • Equation of state of DC-HgGa{sub 2}S{sub 4} determined (bulk modulus of 48.4 GPa). • Calculated elastic constants of DC-HgGa{sub 2}S{sub 4} reported at different pressures. • DC-HgGa{sub 2}S{sub 4} becomes mechanically unstable above 13.8 GPa. -- Abstract: In this work, we focus on the study of the structural and elastic properties of mercury digallium sulfide (HgGa{sub 2}S{sub 4}) at high pressures. This compound belongs to the family of AB{sub 2}X{sub 4} ordered-vacancy compounds and exhibits a tetragonal defect chalcopyrite structure. X-ray diffraction measurements at room temperature have been performed under compression up to 15.1 GPa in a diamond anvil cell. Our measurements have been complemented and compared with ab initio total energy calculations. The axial compressibility and the equation of state of the low-pressure phase of HgGa{sub 2}S{sub 4} have been experimentally and theoretically determined and compared to other related ordered-vacancy compounds. The pressure dependence of the theoretical cation–anion and vacancy-anion distances and compressibilities in HgGa{sub 2}S{sub 4} are reported and discussed in comparison to other related ordered-vacancy compounds. Finally, the pressure dependence of the theoretical elastic constants and elastic moduli of HgGa{sub 2}S{sub 4} has been studied. Our calculations indicate that the low-pressure phase of HgGa{sub 2}S{sub 4} becomes mechanically unstable above 13.8 GPa.

  7. Characteristics of chemical bond and vacancy formation in chalcopyrite-type CuInSe2 and related compounds

    International Nuclear Information System (INIS)

    Maeda, Tsuyoshi; Wada, Takahiro

    2009-01-01

    We studied characteristics of chemical bond and vacancy formation in chalcopyrite-type CuInSe 2 (CIS) by first principles calculations. The chalcopyrite-type CIS has two kinds of chemical bonds, Cu-Se and In-Se. The Cu-Se bond is a weak covalent bonding because electrons occupy both bonding and antibonding orbitals of Cu 3d and Se 4p and occupy only the bonding orbital (a 1 ) of Cu 4s and Se 4p and do not occupy the antibonding orbital (a 1 * ) of Cu 4s and Se 4p. On the other hand, the In-Se bond has a partially covalent and partially ionic character because the In 5s orbital covalently interacts with Se 4p; the In 5p orbital is higher than Se 4p and so the electron in the In 5p orbital moves to the Se 4p orbital. The average bond order of the Cu-Se and In-Se bonds can be calculated to be 1/4 and 1, respectively. The bond order of Cu-Se is smaller than that of In-Se. The characteristics of these two chemical bonds are related to the formation of Cu and In vacancies in CIS. The formation energy of the Cu vacancy is smaller than that of the In vacancy under both Cu-poor and In-poor conditions. The displacement (Δl) of the surrounding Se atoms after the formation of the Cu vacancy is smaller than the Δl after the formation of the In vacancy. The interesting and unique characteristics of CIS are discussed on the basis of the characteristics of the chemical bond. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  8. Evidence for the existence of two electronic states in the chalcopyrite-type alloys CuFe(S1-zSez)2

    International Nuclear Information System (INIS)

    Jaimes, E.; Gonzalez, J.; Woolley, J.C.; Lamarche, G.

    1994-01-01

    Results of Moessbauer spectroscopy for the chalcopyrite-type of alloys CuFe(S 1-z Se z ) 2 in the range of composition 0 ≤ z ≤ 0.45 are presented. Room temperature spectra show two contributions: one is a magnetic spectrum (six lines) with a value of the hyperfine field near to that of chalcopyrite (z = 0, in which an antiferromagnetic order occurs below T = 823 K), the other having only one line. The relative area of the single-line contribution increases as z increases. For z = 0.2, we also made Moessbauer measurements as a function of temperature. The ratio of the two contributions evolves according to a Boltzmann law, in which the single line corresponds to the excited state at 81 K above the antiferromagnetic ground state. (orig.)

  9. Defect chalcopyrite Cu(In{sub 1-x}Ga{sub x}){sub 3}Se{sub 5} (0

    Energy Technology Data Exchange (ETDEWEB)

    Contreras, M.A.; Wiesner, H.; Niles, D.; Ramanathan, K.; Matson, R. [National Renewable Energy Lab., Golden, CO (United States)] [and others

    1996-05-01

    Crystallographic, optical, and electrical properties of defect chalcopyrite Cu(In{sub 1{minus}x}Ga{sub x}){sub 3}Se{sub 5} (0chalcopyrite CuIn{sub 1 {minus}x}Ga{sub x}Se{sub 2} absorber materials is presented. Considering the chalcopyrite/defect chalcopyrite junction model, the authors postulate that the traditionally poor device performance of uniform high-Ga-content absorbers (x>0.3) is due to a relatively inferior character - both structural and electrical - at the very chalcopyrite/defect chalcopyrite interface. They demonstrate that this situation can be circumvented (for absorbers with x>0.3) by properly engineering such an interface by reducing Ga content in the region near the surface of the absorber.

  10. Flotation of Chalcopyrite and Molybdenite in the Presence of Organics in Water

    Directory of Open Access Journals (Sweden)

    Maria Sinche-Gonzalez

    2016-10-01

    Full Text Available One of the water constituents that has not been investigated in great detail for potential detrimental effect on mineral flotation is organic matter. This study investigates the effect of natural organic materials contained in water, such as humic, fulvic and tannic acids, on the flotation of copper and molybdenum sulphides in alkaline conditions and in concentrations similar to those found in natural waters. Results show that copper and molybdenum grades decreased with the addition of humic, tannic and fulvic acid in that order, with a larger depression of molybdenite grade and recovery. Adsorption studies using ultraviolet (UV-visible spectroscopy and X-ray photoelectron spectrometer (XPS surface analysis confirmed that these organic materials were adsorbed on the minerals surface. Complimentary analyses of froth characteristics, particle size distribution and fine particles entrainment were also conducted to explain the cause of the negative effect of these organic materials on flotation. The flotation results were explained in terms of the decrease in the hydrophobicity of the mineral surfaces due to the adsorption of hydrophilic groups in these organic materials which then prevent bubble-particle adhesion. The larger detrimental effect of humic acid is due to its higher adsorption on the minerals, high molecular weight and carbon content compared with the other organic acids used.

  11. Electronic structure of epitaxial chalcopyrite surfaces and interfaces for photovoltaics; Elektronische Struktur epitaktischer Chalkopyrite und deren Heterokontakte fuer die Photovoltaik

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, Andreas

    2012-02-14

    This thesis constitutes a comprehensive study of the surface physics of epitaxial CuInSe{sub 2} films. It comprises analyses of the surface morphology and reconstruction, electronic band structure as well as hetero-junctions relevant to photovoltaic applications. Therefore, especially the aspect of stoichiometry variation from the CuInSe{sub 2} to the copper-deficient defect phases was considered. Preparation and analysis was completely performed under ultra-high vacuum conditions in order to ensure the investigation of well-defined samples free of contaminants. For some of the analysis techniques, single-crystalline samples are indispensable: They allow for the determination of surface periodicity by low-energy electron diffraction (LEED). In combination with concentration depth profiling by angle-resolved x-ray photoemission, to types of surface reconstructions could be distinguished for the near-stoichiometric CuInSe{sub 2}(112) surface. In the copper-rich case, it is stabilized by Cu{sub In} anti-site defects and on the indium-rich side by 2 V{sub Cu} defects, as predicted by surface total energy calculations by Jaffe and Zunger. Both configurations correspond to a c(4 x 2) reconstruction of the zinc blende type (111) surface. For the defect compound CuIn{sub 3}Se{sub 5}, a sphalerite order of the surface was found, which points at a weakening or absence of the chalcopyrite order in the bulk of the material. The unusual stability of the (112) surface could also be proven by comparison with the reconstruction and surface order of (001) and (220) surfaces. The results from surface analysis were used to measure the valence band structure of the epitaxial samples by synchrotron-based angle-resolved photoelectron spectroscopy. The CuInSe{sub 2}(001) surface gives access to the high symmetry directions {Gamma}-T and {Gamma}-N of momentum space. By contrasting the data obtained for the stoichiometric surface with the copper-poor defect compound, a reduction of the

  12. Complete genome sequence of Acidihalobacter prosperus strain F5, an extremely acidophilic, iron- and sulfur-oxidizing halophile with potential industrial applicability in saline water bioleaching of chalcopyrite.

    Science.gov (United States)

    Khaleque, Himel N; Corbett, Melissa K; Ramsay, Joshua P; Kaksonen, Anna H; Boxall, Naomi J; Watkin, Elizabeth L J

    2017-11-20

    Successful process development for the bioleaching of mineral ores, particularly the refractory copper sulfide ore chalcopyrite, remains a challenge in regions where freshwater is scarce and source water contains high concentrations of chloride ion. In this study, a pure isolate of Acidihalobacter prosperus strain F5 was characterized for its ability to leach base metals from sulfide ores (pyrite, chalcopyrite and pentlandite) at increasing chloride ion concentrations. F5 successfully released base metals from ores including pyrite and pentlandite at up to 30gL -1 chloride ion and chalcopyrite up to 18gL -1 chloride ion. In order to understand the genetic mechanisms of tolerance to high acid, saline and heavy metal stress the genome of F5 was sequenced and analysed. As well as being the first strain of Ac. prosperus to be isolated from Australia it is also the first complete genome of the Ac. prosperus species to be sequenced. The F5 genome contains genes involved in the biosynthesis of compatible solutes and genes encoding monovalent cation/proton antiporters and heavy metal transporters which could explain its abilities to tolerate high salinity, acidity and heavy metal stress. Genome analysis also confirmed the presence of genes involved in copper tolerance. The study demonstrates the potential biotechnological applicability of Ac. prosperus strain F5 for saline water bioleaching of mineral ores. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Scientific communications: Re-Os sulfide (bornite, chalcopyrite, and pyrite) systematics of the carbonate-hosted copper deposits at ruby creek, southern brooks range, Alaska

    Science.gov (United States)

    Selby, D.; Kelley, K.D.; Hitzman, M.W.; Zieg, J.

    2009-01-01

    New Re-Os data for chalcopyrite, bornite, and pyrite from the carbonate-hosted Cu deposit at Ruby Creek (Bornite), Alaska, show extremely high Re abundances (hundreds of ppb, low ppm) and contain essentially no common Os. The Re-Os data provide the first absolute ages of ore formation for the carbonate-hosted Ruby Creek Cu-(Co) deposit and demonstrate that the Re-Os systematics of pyrite, chalcopyrite, and bornite are unaffected by greenschist metamorphism. The Re-Os data show that the main phase of Cu mineralization pre dominantly occurred at 384 ?? 4.2 Ma, with an earlier phase possibly at ???400 Ma. The Re-Os data are consistent with the observed paragenetic sequence and coincide with zircon U-Pb ages from igneous rocks within the Ambler metallogenic belt, some of which are spatially and genetically associated with regional volcanogenic massive sulfide deposits. The latter may suggest a temporal link between regional magmatism and hydrothermal mineralization in the Ambler district. The utility of bornite and chalcopyrite, in addition to pyrite, contributes to a new understanding of Re-Os geochronology and permits a refinement of the genetic model for the Ruby Creek deposit. ?? 2009 Society of Economices Geologists, Inc.

  14. Impact on sediments and water by release of copper from chalcopyrite bearing rock due to acidic mine drainage

    Science.gov (United States)

    Shukla, Anoop Kant; Pradhan, Manoj; Tiwari, Onkar Nath

    2018-04-01

    Mining activity causes transition of rock-mass from its original position in earth into open environment. The action of environmental elements such air, water, microorganisms leads to oxidation of minerals which constitute the rock. The oxidation of sulphide minerals in presence of moisture releases acidic mine discharge (AMD). The acidic nature of AMD causes leaching of metals from rock minerals. Dissolution of other minerals may occur upon reaction with AMD. Chalcopyrite (CuFeS2) undergoes oxidation in acidic condition releasing copper among other products. This study reveals contamination of copper in sediment samples and seepage water from the tailing dam of a large copper project in located in central India. Elevation was studied using GIS to ascertain to the topographic elevation of tailing dam area. It was located at relatively high altitude causing seepage to flow away from tailing dam. The seepage water from tailing dam was found to be acidic with mean pH value of 4.0 and elevated copper content. Similarly, sediments from seepage water flow displayed elevated copper concentration. The copper concentration in seepage water was found with a mean value of 10.73 mg/l. The sediments from seepage water flow also displayed elevated copper concentration with mean value of 26.92 g/kg. This indicates impact on sediments by release of copper due to acidic mine drainage.

  15. In situ investigation of wet chemical processes for chalcopyrite solar cells by L-edge XAS under ambient conditions

    Energy Technology Data Exchange (ETDEWEB)

    Greil, Stefanie M. [Helmholtz-Zentrum Berlin fuer Materialien und Energie, Albert-Einstein-Strasse 15, 12489 Berlin (Germany); Lauermann, Iver, E-mail: Iver.lauermann@helmholtz-berlin.d [Helmholtz-Zentrum Berlin fuer Materialien und Energie, Albert-Einstein-Strasse 15, 12489 Berlin (Germany); Ennaoui, Ahmed; Kropp, Timo; Lange, Kathrin M.; Weber, Matthieu [Helmholtz-Zentrum Berlin fuer Materialien und Energie, Albert-Einstein-Strasse 15, 12489 Berlin (Germany); Aziz, Emad F., E-mail: Emad.Aziz@helmholtz-berlin.d [Helmholtz-Zentrum Berlin fuer Materialien und Energie, Albert-Einstein-Strasse 15, 12489 Berlin (Germany)

    2010-02-15

    Two instrumental setups for in situ soft X-ray absorption spectroscopy in liquid systems are demonstrated in this work. One for investigating chemical reactions in solutions and a new one for the solid component of a liquid / (as in both / absorber) solid interface. We used these setups for investigating two production processes for chalcopyrite solar cells under ambient conditions, probing the L-edge of Zn and Cu. The first one is a flow cell with a silicon nitride membrane to study the chemical bath deposition process for Cd-free buffer layers. Examining the electronic structure of involved Zn complexes allows to determine the exact reaction mechanism taking place during this process. The second setup is a rotating disk for investigating the bath/absorber interface upon the etching process of superficial binary copper compounds of the absorber as a function of time. The time resolution of the chemical reaction demonstrated in this study ranges from the second to minute time scale.

  16. In situ investigation of wet chemical processes for chalcopyrite solar cells by L-edge XAS under ambient conditions

    International Nuclear Information System (INIS)

    Greil, Stefanie M.; Lauermann, Iver; Ennaoui, Ahmed; Kropp, Timo; Lange, Kathrin M.; Weber, Matthieu; Aziz, Emad F.

    2010-01-01

    Two instrumental setups for in situ soft X-ray absorption spectroscopy in liquid systems are demonstrated in this work. One for investigating chemical reactions in solutions and a new one for the solid component of a liquid / (as in both / absorber) solid interface. We used these setups for investigating two production processes for chalcopyrite solar cells under ambient conditions, probing the L-edge of Zn and Cu. The first one is a flow cell with a silicon nitride membrane to study the chemical bath deposition process for Cd-free buffer layers. Examining the electronic structure of involved Zn complexes allows to determine the exact reaction mechanism taking place during this process. The second setup is a rotating disk for investigating the bath/absorber interface upon the etching process of superficial binary copper compounds of the absorber as a function of time. The time resolution of the chemical reaction demonstrated in this study ranges from the second to minute time scale.

  17. In situ investigation of wet chemical processes for chalcopyrite solar cells by L-edge XAS under ambient conditions

    Science.gov (United States)

    Greil, Stefanie M.; Lauermann, Iver; Ennaoui, Ahmed; Kropp, Timo; Lange, Kathrin M.; Weber, Matthieu; Aziz, Emad F.

    2010-02-01

    Two instrumental setups for in situ soft X-ray absorption spectroscopy in liquid systems are demonstrated in this work. One for investigating chemical reactions in solutions and a new one for the solid component of a liquid / (as in both / absorber) solid interface. We used these setups for investigating two production processes for chalcopyrite solar cells under ambient conditions, probing the L-edge of Zn and Cu. The first one is a flow cell with a silicon nitride membrane to study the chemical bath deposition process for Cd-free buffer layers. Examining the electronic structure of involved Zn complexes allows to determine the exact reaction mechanism taking place during this process. The second setup is a rotating disk for investigating the bath/absorber interface upon the etching process of superficial binary copper compounds of the absorber as a function of time. The time resolution of the chemical reaction demonstrated in this study ranges from the second to minute time scale.

  18. First-principles study of structural, electronic, linear and nonlinear optical properties of Ga{2}PSb ternary chalcopyrite

    Science.gov (United States)

    Ouahrani, T.; Reshak, A. H.; de La Roza, A. Otero; Mebrouki, M.; Luaña, V.; Khenata, R.; Amrani, B.

    2009-12-01

    We report results from first-principles density functional calculations using the full-potential linear augmented plane wave (FP-LAPW) method. The generalized gradient approximation (GGA) and the Engel-Vosko-generalized gradient approximation (EV-GGA) were used for the exchange-correlation energy of the structural, electronic, linear and nonlinear optical properties of the chalcopyrite Ga2PSb compound. The valence band maximum (VBM) is located at the Γv point, and the conduction band minimum (CBM) is located at the Γc point, resulting in a direct band gap of about 0.365 eV for GGA and 0.83 eV for EV-GGA. In comparison with the experimental one (1.2 eV) we found that EV-GGA calculation gives energy gap in reasonable agreement with the experiment. The spin orbit coupling has marginal influence on the optical properties. The ground state quantities such as lattice parameters (a, c and u), bulk modules B and its pressure derivative B^primeare evaluated.

  19. Structural, elastic, electronic, bonding, and optical properties of BeAZ2 (A = Si, Ge, Sn; Z = P, As) chalcopyrites

    International Nuclear Information System (INIS)

    Fahad, Shah; Murtaza, G.; Ouahrani, T.; Khenata, R.; Yousaf, Masood; Omran, S.Bin; Mohammad, Saleh

    2015-01-01

    A first principles density functional theory (DFT) technique is used to study the structural, chemical bonding, electronic and optical properties of BeAZ 2 (A = Si, Ge, Sn; Z = P, As) chalcopyrite materials. The calculated parameters are in good agreement with the available experimental results. The lattice constants and the equilibrium volume increased as we moved from Si to Ge to Sn, whereas the c/a and internal parameters u decreased by shifting the cation from P to As. These compounds are elastically stable. An investigation of the band gap using the WC-GGA, EV-GGA, PBE-GGA and mBJ-metaGGA potentials suggested that BeSiP 2 and BeSiAs 2 are direct band gap compounds, whereas BeGeP 2, BeGeAs 2, BeSnP 2, BeSnAs 2 are indirect band gap compounds. The energy band gaps decreased by changing B from Si to Sn and increased by changing the anion C from P to As. The bonding among the cations and anions is primarily ionic. In the optical properties, the real and imaginary parts of the dielectric functions, reflectivity and optical conductivity have been studied over a wide energy range. - Highlights: • The compounds are studied by FP-LAPW method within mBJ approximation. • All of the studied materials show isotropic behaviour. • All the compounds show direct band gap nature. • Bonding nature is mostly covalent among the studied compounds. • High absorption peaks and reflectivity ensures there utility in optoelectronic devices

  20. The n-Cu0.9Ag0.1In3Se5 chalcopyrite, electronic as well as ionic conductor

    International Nuclear Information System (INIS)

    Diaz, R

    2008-01-01

    A resistance increase with time of the n-Cu 0.9 Ag 0.1 In 3 Se 5 chalcopyrite has been observed. This new effect is analysed in terms of a hypothesis of ion migration and Schottky barrier formation. These results might explain why different solar cell efficiencies are obtained for the chalcopyrites, CuInSe 2 and CuIn x Ga 1-x Se 2 , when an In-rich film is deposited on top of the chalcopyrite. In these solar cells, ion migration can exist and a new effect appears similar to the one observed in our compound. The ions, probably the cations, are moved by the electrical field towards the cathode. A gradient of mobile ions appears across the sample and the positive charge is accumulated near this electrode such that it varies the metal-semiconductor interface. This interface is a Schottky barrier where the contact potential is a function of time due to the arrival of ions. The electrical measurements have been carried out on a solid state device, graphite/n-Cu 0.9 Ag 0.1 In 3 Se 5 /graphite. The current intensity and the potential drop across the sample have been measured with time when a constant electrical potential is applied for 600 s at dark or under ultraviolet illumination and at room temperature. A comparative study in similar electrical conditions is done; the current intensity difference and the potential drop across the difference (under ultraviolet illumination minus at dark) are not constant and both measurements increase with time

  1. A Study of the Effect of Djurliete, Bornite and Chalcopyrite during the Dissolution of Gold with a Solution of Ammonia-Cyanide

    Directory of Open Access Journals (Sweden)

    Mike Fulton

    2012-11-01

    Full Text Available The high solubility of copper sulphide minerals is an issue in the cyanidation of gold ores. The objective of this study was to quantify the effect of individual copper sulphide minerals on the Hunt process, which showed advantages over cyanidation. High purity djurleite, bornite and chalcopyrite, with a P70 of 70–74 microns, were mixed with fine quartz and gold powder (3–8 micron to obtain a copper concentration of 0.3%. The ammonia-cyanide leaching of slurry with djurleite proved to be more effective than cyanidation; producing comparable extraction of gold (99%, while reducing the cyanide consumption from 5.8 to 1.2 kg/t NaCN. Lead nitrate improved the Hunt leaching. The lower cyanide consumption is associated to a significant reduction of copper dissolved. XPS surface analysis of djurleite showed that lead nitrate favored the formation of Cu(OH2 species. Lead was also detected on the surface (oxide or hydroxide. Sulphide and copper compounds (cyanide and sulphide were reaction products responsible for inhibiting the dissolution of gold. Lead nitrate added in the Hunt leaching of bornite produced 99% gold extraction. Surface reaction products were similar to djurleite. The cyanide consumption (~4.4 kg/t NaCN was not reduced by the addition of ammonia. Cyanidation of chalcopyrite showed a lower consumption of cyanide 0.33 kg/t NaCN compared to 0.21 kg/t NaCN for Hunt. No significant interferences were observed in gold leaching with a slurry containing chalcopyrite.

  2. Synthesis of single phase chalcopyrite CuIn1−xGaxSe2 (0 ≤ x ≤ 1) nanoparticles by one-pot method

    International Nuclear Information System (INIS)

    Han, Zhaoxia; Zhang, Dawei; Chen, Qinmiao; Hong, Ruijin; Tao, Chunxian; Huang, Yuanshen; Ni, Zhengji; Zhuang, Songlin

    2014-01-01

    Graphical abstract: - Highlights: • A facile and rapid one-pot synthesis method is presented. • The effects of various Ga contents are investigated. • Single phase chalcopyrite CuIn 1−x Ga x Se 2 nanoparticles can be easily synthesized. • The phase formation sequence is from CuSe to CuGaSe 2 , then to CuIn 1−x Ga x Se 2 . • The possible reaction mechanism of CuIn 1−x Ga x Se 2 nanoparticles is proposed. - Abstract: Single phase chalcopyrite and near stoichiometric CuIn 1−x Ga x Se 2 (0 ≤ x ≤ 1) nanoparticles were successfully synthesized by using a facile and rapid one-pot method. The effects of various Ga contents on crystal phase, morphology, element composition and absorption spectrum of the as-synthesized CuIn 1−x Ga x Se 2 nanoparticles were investigated in detail. The XRD and Raman patterns indicated that the as-synthesized nanoparticles had a single phase chalcopyrite structure, and the diffraction peaks shifted toward larger diffraction angles or higher frequencies with increasing Ga content. The FE-SEM images showed that the as-synthesized nanoparticles were polydispersed in both size and shape, and the nanoparticles with higher Ga content were more prone to aggregate. The Vis–IR absorption spectra showed strong absorption in the entire visible light region. The estimated band gap increased from 1.00 eV to 1.68 eV as Ga content increasing

  3. Expression of Critical Sulfur- and Iron-Oxidation Genes and the Community Dynamics During Bioleaching of Chalcopyrite Concentrate by Moderate Thermophiles.

    Science.gov (United States)

    Zhou, Dan; Peng, Tangjian; Zhou, Hongbo; Liu, Xueduan; Gu, Guohua; Chen, Miao; Qiu, Guanzhou; Zeng, Weimin

    2015-07-01

    Sulfate adenylyltransferase gene and 4Fe-4S ferredoxin gene are the key genes related to sulfur and iron oxidations during bioleaching system, respectively. In order to better understand the bioleaching and microorganism synergistic mechanism in chalcopyrite bioleaching by mixed culture of moderate thermophiles, expressions of the two energy metabolism genes and community dynamics of free and attached microorganisms were investigated. Specific primers were designed for real-time quantitative PCR to study the expression of these genes. Real-time PCR results showed that sulfate adenylyltransferase gene was more highly expressed in Sulfobacillus thermosulfidooxidans than that in Acidithiobacillus caldus, and expression of 4Fe-4S ferredoxin gene was higher in Ferroplasma thermophilum than that in S. thermosulfidooxidans and Leptospirillum ferriphilum. The results indicated that in the bioleaching system of chalcopyrite concentrate, sulfur and iron oxidations were mainly performed by S. thermosulfidooxidans and F. thermophilum, respectively. The community dynamics results revealed that S. thermosulfidooxidans took up the largest proportion during the whole period, followed by F. thermophilum, A. caldus, and L. ferriphilum. The CCA analysis showed that 4Fe-4S ferredoxin gene expression was mainly affected (positively correlated) by high pH and elevated concentration of ferrous ion, while no factor was observed to prominently influence the expression of sulfate adenylyltransferase gene.

  4. Tunable optical properties of ZnCdTe2-xSex(x =0.625) chalcopyrite for photovoltaics; a mBJLDA approach

    Science.gov (United States)

    Kashyap, Manish K.; Paudyal, D.; Harmon, B. N.

    In the present study, we have performed ab-initio simulations of sp-element defect in ZnCdTe2-xSex (x =0.625) chalcopyrite to check the tuning of band gap as compared to the pristine case. The exchange and correlation (XC) effects are taken into account by an orbital independent modified Becke-Johnson (mBJ) potential as coupled with Local Density Approximation (LDA) for these calculations. The calculated energy band structures show a direct band gap at the point in the brillouin zone for the pristine as well as the defected case and the band gap decreases with inclusion of sp-disorder. The imaginary dielectric function predicts the optical band gap of pristine ZnCdTe2 very close to the experimental value and the results are in reasonable agreement without applying any scissor operator. With inclusion of sp-element defect, the optical spectra is tuned to optimal region, suitable for photovoltaics. It is apparent that mBJ functional is well suited for calculating electronic structure of pristine as well as defected ZnCdTe2chalcopyrite. MKK acknowledges financial support from UGC, India in the form of RAMAN Post-doctoral fellowship. This work at Ames Laboratory was supported by the DOE, Office of Basic Energy Sciences, Materials Sciences Division under contract No. DE-AC02-07CH11358.

  5. In situ monitoring the growth of thin-film ZnS/Zn (S,O) bilayer on Cu-chalcopyrite for high performance thin film solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Saez-Araoz, R.; Abou-Ras, D. [Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Solar Energy Division, Glienicker Strasse 100, 14109 Berlin (Germany); Niesen, T.P. [AVANCIS GmbH and Co KG Otto-Hahn-Ring 6, 81739 Munich (Germany); Neisser, A.; Wilchelmi, K. [SULFURCELL Solartechnik GmbH Barbara-McClintock-Strasse 11, 12489 Berlin (Germany); Lux-Steiner, M.Ch. [Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Solar Energy Division, Glienicker Strasse 100, 14109 Berlin (Germany); Ennaoui, A. [Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Solar Energy Division, Glienicker Strasse 100, 14109 Berlin (Germany)], E-mail: ennaoui@helmholtz-berlin.de

    2009-02-02

    This paper highlights the crucial role that the control of the chemical bath deposition (CBD) process plays for buffer production of Cu-chalcopyrite solar-cell devices. ZnS/Zn (S,O) bilayer was deposited on CuInS{sub 2} (CIS) and Cu(In,Ga)(SSe){sub 2} (CIGSSe) and monitored using turbidity measurements of the solution. The results were correlated to the X-ray photoemission spectra of the samples obtained by interruption of the process at sequential stages. Two different feature regimes were distinguished: In the first stage, a heterogeneous reaction takes place on the absorber resulting in the formation of pure ZnS. The second stage of the process is homogeneous, and the in-situ turbidity measurement shows a loss in the transmission of light through the CBD solution. The measured ZnL3M45M45 Auger-peaks, during this second stage of the process, show a shift of the kinetic energy from pure ZnS to a solid-solution ZnS/ZnO ('Zn (S,O)') with decreasing amount of sulfur. These results are supported by the observations from Energy-filtered transmission electron microscopy. This paper also demonstrates that monitoring of the CBD process combined with the basic understanding using surface and interface analysis have contributed to improve the reproducibility and to enhance the photovoltaic performance of Cu-chalcopyrite thin-film solar modules.

  6. In situ monitoring the growth of thin-film ZnS/Zn (S,O) bilayer on Cu-chalcopyrite for high performance thin film solar cells

    International Nuclear Information System (INIS)

    Saez-Araoz, R.; Abou-Ras, D.; Niesen, T.P.; Neisser, A.; Wilchelmi, K.; Lux-Steiner, M.Ch.; Ennaoui, A.

    2009-01-01

    This paper highlights the crucial role that the control of the chemical bath deposition (CBD) process plays for buffer production of Cu-chalcopyrite solar-cell devices. ZnS/Zn (S,O) bilayer was deposited on CuInS 2 (CIS) and Cu(In,Ga)(SSe) 2 (CIGSSe) and monitored using turbidity measurements of the solution. The results were correlated to the X-ray photoemission spectra of the samples obtained by interruption of the process at sequential stages. Two different feature regimes were distinguished: In the first stage, a heterogeneous reaction takes place on the absorber resulting in the formation of pure ZnS. The second stage of the process is homogeneous, and the in-situ turbidity measurement shows a loss in the transmission of light through the CBD solution. The measured ZnL3M45M45 Auger-peaks, during this second stage of the process, show a shift of the kinetic energy from pure ZnS to a solid-solution ZnS/ZnO ('Zn (S,O)') with decreasing amount of sulfur. These results are supported by the observations from Energy-filtered transmission electron microscopy. This paper also demonstrates that monitoring of the CBD process combined with the basic understanding using surface and interface analysis have contributed to improve the reproducibility and to enhance the photovoltaic performance of Cu-chalcopyrite thin-film solar modules

  7. The structural, elastic, electronic and dynamical properties of chalcopyrite semiconductor BeGeAs{sub 2} from first-principles calculations

    Energy Technology Data Exchange (ETDEWEB)

    Ciftci, Yasemin Oe. [Gazi University Teknikokullar, Department of Physics, Faculty of Sciences, Ankara (Turkey); Evecen, Meryem; Aldirmaz, Emine [Amasya University, Department of Physics, Faculty of Arts and Sciences, Amasya (Turkey)

    2017-01-15

    First-principles calculations for the structural, elastic, electronic and vibrational properties of BeGeAs{sub 2} with chalcopyrite structure have been reported in the frame work of the density functional theory. The calculated ground state properties are in good agreement with the available data. By considering the electronic band structure and electronic density of states calculation, it is found that this compound is a semiconductor which confirmed the previous work. Single-crystal elastic constants and related properties such as Young's modulus, Poisson ratio, shear modulus and bulk modulus have been predicted using the stress-finite strain technique. It can be seen from the calculated elastic constants that this compound is mechanically stable in the chalcopyrite structure. Pressure dependences of elastic constants and band gap are also reported. Finally, the phonon dispersion curves and total and partial density of states were calculated and discussed. The calculated phonon frequencies BeGeAs{sub 2} are positive, indicating the dynamical stability of the studied compound. (orig.)

  8. Teachers' Grading Decision Making

    Science.gov (United States)

    Isnawati, Ida; Saukah, Ali

    2017-01-01

    This study investigated teachers' grading decision making, focusing on their beliefs underlying their grading decision making, their grading practices and assessment types, and factors they considered in grading decision making. Two teachers from two junior high schools applying different curriculum policies in grade reporting in Indonesian…

  9. Student Attitudes Toward Grades and Grading Practices.

    Science.gov (United States)

    Stallings, William M.; Leslie, Elwood K.

    The result of a study designed to assess student attitudes toward grading practices are discussed. Questionnaire responses of 3439 students in three institutions were tabulated. Responses were generally negative toward conventional grading systems. (MS)

  10. Prediction of electronic and optical properties of ZnAl2Te4 defect chalcopyrite semiconductor: an ab-initio study

    Science.gov (United States)

    Mayengbam, Rishikanta; Tripathy, S. K.; Pandey, B. P.

    2018-03-01

    In this paper, we have investigated the structural, electronic and optical properties of ZnAl2Te4 defect chalcopyrite semiconductor using generalized gradient approximation (GGA) within density functional theory (DFT). We have calculated the optimized lattice constants (a and c) and compared with the available experimental values. The optimized lattice constants have been used to calculate the energy band gap and found to be 1.57 eV. The partial density of states and total density of states have been discussed in detail. The frequency dependent dielectric constant and refractive index have been calculated and plotted in the energy range 0-13 eV. All the above parameters have been compared with the available experimental and theoretical values and found good agreement between them.

  11. First and second harmonic generation of the XAl{sub 2}Se{sub 4} (X=Zn,Cd,Hg) defect chalcopyrite compounds

    Energy Technology Data Exchange (ETDEWEB)

    Ouahrani, Tarik, E-mail: tarik_ouahrani@yahoo.fr [Laboratoire de Physique Theorique, Universite de Tlemcen, B.P.230,13000 Tlemcen (Algeria); Ecole Preparatoire en Sciences et Techniques, Depertement de Physique EPST-T, Tlemcen 13000 (Algeria); Khenata, R. [Laboratoire de Physique Quantique et de Modelisation Mathematique (LPQ3M), Universite de Mascara, 29000 Mascara (Algeria); Lasri, B. [Laboratoire de Physique Theorique, Universite de Tlemcen, B.P.230,13000 Tlemcen (Algeria); Universite Dr Tahar Moulay de Saida, B.P. 138, Cite el Nasr, Saida 20000 (Algeria); Reshak, Ali H. [School of Complex systems, FFPW- South Bohemia University, Nove Hrady 37333 (Czech Republic); School of Material Engineering, Malaysia University of Perlis, P.O Box 77, d/a Pejabat Pos Besar, 01007 Kangar, Perlis (Malaysia); Bouhemadou, A. [Department of Physics, Faculty of Sciences, University of Setif, 19000 Setif (Algeria); Bin-Omran, S. [Department of Physics and Astronomy, Faculty of Science, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia)

    2012-09-15

    The chemical bonding of the ZnAl{sub 2}Se{sub 4}, CdAl{sub 2}Se{sub 4} and HgAl{sub 2}Se{sub 4} defect chalcopyrites has been studied in the framework of the quantum theory of atoms in molecules (AIM). The GW quasi-particle approximation is used to correct the DFT-underestimation of energy gap, and as a consequence the linear and nonlinear optical properties are significantly enhanced. The second harmonic generation (SHG) displays certain dependence with the ionicity degree decrease through the dependency of the SHG on the band gap. The occurrence of the AIM saddle point is characterized and some clarifying features in relationship with the density topology are exposed, which enable to understand the relation with the second harmonic generation effect.

  12. Influence of temperature on the fixation and penetration of silver during the chalcopyrite leaching using moderate thermophilic microorganisms; Influencia de la temperatura en la fijacion y penetracion de la plata durante la lixiviacion de calcopirita con microorganismos termofilos moderados

    Energy Technology Data Exchange (ETDEWEB)

    Cancho, L.; Blazquez, M. L.; Munoz, J. A.; Gonzalez, F.; Ballester, A.

    2004-07-01

    Bio leaching of chalcopyrite using mesophilic microorganisms considerable improves in the presence of silver. However, the studies carried out with moderate thermophilic microorganisms do not show a significant improvement with regard to the use of mesophilic bacteria. The main objective of the present work has been to study the silver fixation on chalcopyrite ar 35 and 45 degree centigree and its influence on the microbiological attack. Different observations using SEM, EDS microanalysis and concentration profiles using electron microprobe have been carried out. The study of the different samples showed that silver fixation was more favourable at 35 degree centigree than at 45 degree centigree. In addition, bacterial action improved silver penetration through attack cracks. (Author)

  13. X-ray diffraction study of chalcopyrite CuFeS2, pentlandite (Fe,Ni)9S8 and Pyrrhotite Fe1-xS obtained from Cu-Ni orebodies

    International Nuclear Information System (INIS)

    Nkoma, J.S.; Ekosse, G.

    1998-05-01

    The X-ray Diffraction (XRD) technique is applied to study five samples of Cu-Ni orebodies, and it is shown that they contain chalcopyrite CuFeS 2 as the source of Cu, pentlandite (Fe,Ni) 9 S 8 as the source of Ni and pyrrhotite Fe 1-x S as a dominant compound. There are also other less dominant compounds such as bunsenite NiO, chalcocite Cu 2 S, penrosite (Ni, Cu)Se 2 and magnetite Fe 3 O 4 . Using the obtained XRD data, we obtain the lattice parameters for tetragonal chalcopyrite as a=b=5.3069A and c=10.3836A, cubic pentlandite as a=b=c=10.0487A, and hexagonal pyrrhotite as a=b=6.8820A and c=22.8037A. (author)

  14. On arbitrarily graded rings

    Indian Academy of Sciences (India)

    58

    paper is devoted to the study of arbitrary rings graded through arbitrary sets. .... which recover certain multiplicative relations among the homogeneous components ... instance the case in which the grading set A is an Abelian group, where the ...

  15. Graded manifolds and supermanifolds

    International Nuclear Information System (INIS)

    Batchelor, M.

    1984-01-01

    In this paper, a review is presented on graded manifolds and supermanifolds. Many theorems, propositions, corrollaries, etc. are given with proofs or sketch proofs. Graded manifolds, supereuclidian space, Lie supergroups, etc. are dealt with

  16. Epitaxial growth of chalcopyrite CuInS2 films on GaAs (001) substrates by evaporation method with elemental sources

    International Nuclear Information System (INIS)

    Nozomu, Tsuboi; Satoshi, Kobayash; Nozomu, Tsuboi; Takashi, Tamogami

    2010-01-01

    Full text : Ternary chalcopyrite semiconductor CuInS 2 is one of the potential candidates for absorber layers in high-efficiency thin film solar cells due to its direct bandgap Eg of 1.5 eV, which matches with solar spectrum. However, CuInS 2 solar cells face the problem of lower solar conversion efficiency compared with Cu(InGa)Se 2 solar cells. Investigation of fundamental properties of CuInS 2 films is necessary to understand key issues for solar cell performance. Although in bulk CuInS 2 is known to crystallize into chalcopyrite (CH) structure, in thin film other structures such as Cu-Au (CA) and sphalerite (SP) structures may coexist. It was reported epitaxial growth of slightly Cu-rich CuInS 2 films with c-axis orientated CA only and/or with a mixture of a- and c-axes orientated CH structures on GaP (001) at substrate temperature of 500 degrees using the conventional evaporation method with three elemental sources. Successful growth of epitaxial CH structured CuInS 2 were observed for films grown on GaP at 570 degrees with slightly Cu-rich composition. In this paper, CuInS 2 films with various [Cu]/[In] ratios are grown on GaAs(001) substrates, and the composition range in terms of the [Cu]/[In] ratio where epitaxial films with CH structure grow and the structural qualities of the films are discussed in comparison with those on GaP substrates. Films with various ratios of [Cu]/[In]=0.8 ≤1.9 are grown at 500 degrees and 570 degrees using the evaporation system described in our previous reports. Regardless of the substrate temperature, noticeable X-ray diffraction (XRD) peaks of CH structured CuInS 2 phase are observed in slightly Cu-rich films. However, reflection high energy electron diffraction (RHEED) patterns of the slightly Cu-rich films grown at 570 degrees exhibit noticeable spots not only due to the CH structure but also due to the CA structure. The amount of the CA structure is considered to be small because of the absence of the XRD peaks of the CA

  17. Optimization of Electrochemically Deposited Highly Doped ZnO Bilayers on Ga-Rich Chalcopyrite Selenide for Cost-Effective Photovoltaic Device Technology

    Directory of Open Access Journals (Sweden)

    Dimitra N. Papadimitriou

    2016-11-01

    Full Text Available High quality polycrystalline bilayers of aluminium doped ZnO (Al:ZnO were successively electrodeposited in the form of columnar structures preferentially oriented along the ( 10 1 ¯ 1 crystallographic direction from aqueous solution of zinc nitrate (Zn(NO32 at negative electrochemical potential of EC = (−0.8–(−1.2 V and moderate temperature of 80 °C on gallium rich (30% Ga chalcopyrite selenide Cu(In,GaSe2 (CIGS with chemically deposited ZnSe buffer (ZnSe/Cu(In,GaSe2/Mo/glass. The aluminium doped ZnO layer properties have initially been probed by deposition of Al:ZnO/i-ZnO bilayers directly on Mo/glass substrates. The band-gap energy of the Al:ZnO/i-ZnO reference layers was found to vary from 3.2 to 3.7 eV by varying the AlCl3 solute dopant concentration from 1 to 20 mM. The electrical resistivity of indium-pellet contacted highly doped Al:ZnO sheet of In/Al:ZnO/i-ZnO/Mo/glass reference samples was of the order ρ ~10−5 Ω·cm; the respective carrier concentration of the order 1022 cm−3 is commensurate with that of sputtered Al:ZnO layers. For crystal quality optimization of the bilayers by maintenance of the volatile selenium content of the chalcopyrite, they were subjected to 2-step annealing under successive temperature raise and N2 flux regulation. The hydrostatic compressive strain due to Al3+ incorporation in the ZnO lattice of bilayers processed successively with 5 and 12 mM AlCl3 dopant was εh = −0.046 and the respective stress σh = −20 GPa. The surface reflectivity of maximum 5% over the scanned region of 180–900 nm and the (optical band gap of Eg = 3.67 eV were indicative of the high optical quality of the electrochemically deposited (ECD Al:ZnO bilayers.

  18. GRADE Equity Guidelines 3

    DEFF Research Database (Denmark)

    Welch, Vivian A; Akl, Elie A; Pottie, Kevin

    2017-01-01

    OBJECTIVE: The aim of this paper is to describe a conceptual framework for how to consider health equity in the GRADE (Grading Recommendations Assessment and Development Evidence) guideline development process. STUDY DESIGN AND SETTING: Consensus-based guidance developed by the GRADE working grou...

  19. Graded gauge theory

    International Nuclear Information System (INIS)

    Kerner, R.

    1983-01-01

    The mathematical background for a graded extension of gauge theories is investigated. After discussing the general properties of graded Lie algebras and what may serve as a model for a graded Lie group, the graded fiber bundle is constructed. Its basis manifold is supposed to be the so-called superspace, i.e. the product of the Minkowskian space-time with the Grassmann algebra spanned by the anticommuting Lorentz spinors; the vertical subspaces tangent to the fibers are isomorphic with the graded extension of the SU(N) Lie algebra. The connection and curvature are defined then on this bundle; the two different gradings are either independent of each other, or may be unified in one common grading, which is equivalent to the choice of the spin-statistics dependence. The Yang-Mills lagrangian is investigated in the simplified case. The conformal symmetry breaking is discussed, as well as some other physical consequences of the model. (orig.)

  20. Defects in Cu(In,Ga)Se{sub 2} chalcopyrite semiconductors: a comparative study of material properties, defect states, and photovoltaic performance

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Qing; Gunawan, Oki; Copel, Matthew; Reuter, Kathleen B; Chey, S Jay; Mitzi, David B [IBM T.J. Watson Research Center, Yorktown Heights, NY (United States); Deline, Vaughn R [IBM Almaden Resesarch Center, San Jose, CA (United States)

    2011-10-15

    Understanding defects in Cu(In,Ga)(Se,S){sub 2} (CIGS), especially correlating changes in the film formation process with differences in material properties, photovoltaic (PV) device performance, and defect levels extracted from admittance spectroscopy, is a critical but challenging undertaking due to the complex nature of this polycrystalline compound semiconductor. Here we present a systematic comparative study wherein varying defect density levels in CIGS films were intentionally induced by growing CIGS grains using different selenium activity levels. Material characterization results by techniques including X-ray diffraction, scanning electron microscopy, transmission electron microscopy, secondary ion mass spectrometry, X-ray photoelectron spectroscopy, and medium energy ion scattering indicate that this process variation, although not significantly affecting CIGS grain structure, crystal orientation, or bulk composition, leads to enhanced formation of a defective chalcopyrite layer with high density of indium or gallium at copper antisite defects ((In, Ga){sub Cu}) near the CIGS surface, for CIGS films grown with insufficient selenium supply. This defective layer or the film growth conditions associated with it is further linked with observed current-voltage characteristics, including rollover and crossover behavior, and a defect state at around 110 meV (generally denoted as the N1 defect) commonly observed in admittance spectroscopy. The impact of the (In, Ga){sub Cu} defects on device PV performance is also established. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  1. Graded tensor calculus

    International Nuclear Information System (INIS)

    Scheunert, M.

    1982-10-01

    We develop a graded tensor calculus corresponding to arbitrary Abelian groups of degrees and arbitrary commutation factors. The standard basic constructions and definitions like tensor products, spaces of multilinear mappings, contractions, symmetrization, symmetric algebra, as well as the transpose, adjoint, and trace of a linear mapping, are generalized to the graded case and a multitude of canonical isomorphisms is presented. Moreover, the graded versions of the classical Lie algebras are introduced and some of their basic properties are described. (orig.)

  2. Electrochemical dissolution of fresh and passivated chalcopyrite electrodes. Effect of pyrite on the reduction of Fe3+ ions and transport processes within the passive film

    International Nuclear Information System (INIS)

    Olvera, O.G.; Quiroz, L.; Dixon, D.G.; Asselin, E.

    2014-01-01

    Graphical abstract: - Highlights: • FeS 2 increased the dissolution rate of fresh and passivated CuFeS 2 electrodes. • Fe 3+ reduction was the rate controlling step in the dissolution of fresh CuFeS 2 . • Diffusion within the passive film controlled the dissolution rate of passivated CuFeS 2 . - Abstract: The effect of pyrite (FeS 2 ) on the electrochemical dissolution of fresh and passivated chalcopyrite (CuFeS 2 ) electrodes has been studied. Current density values for the dissolution of CuFeS 2 were calculated from EIS measurements. FeS 2 increased the dissolution rate of fresh and passivated CuFeS 2 electrodes indicating that the galvanic effect continued even after the electrode was chemically passivated. The dissolution rate of CuFeS 2 decreased by a factor of 3 after the passivation treatment. Due to the low diffusion rates of ions within the CuFeS 2 passive film and due to an increase in the resistance to the transfer of electrons at the electrode/film interface, the activity of FeS 2 for the reduction of Fe 3+ ions was also reduced by a factor of 2.3 even though FeS 2 was not exposed to any chemical treatment. The results in this work indicate that the dissolution rate of the fresh CuFeS 2 electrode was controlled by the reduction of Fe 3+ ions whereas for the passivated CuFeS 2 electrode the dissolution rate was controlled by diffusion within the passive film

  3. Electronic structure of semiconductor thin films (chalcopyrites) as absorbermaterials for thin film solar cells; Elektronische Struktur duenner Halbleiterfilme (Chalkopyrite) als Absorbermaterialien fuer Duennschichtsolarzellen

    Energy Technology Data Exchange (ETDEWEB)

    Lehmann, Carsten

    2007-12-11

    The objective of this work was to determine for the first time the band structure of CuInS{sub 2}. For this purpose a new GSMBE process with TBDS as sulphur precursor was established to prevent the use of elemental sulphur in an UHV system. Additionally to the deposited films a cleave surface was prepared. The samples were characterized in situ by XPS/UPS and LEED. XRD and SEM were used for further ex situ investigations. The band structure was determined by ARUPS using synchrotron light. CuInS(001) and CuInS{sub 2}(112) were deposited on Si and GaAs. The deposition of CuInS{sub 2} on GaAs showed a strong dependence on the existing surface reconstruction. A 2 x 1 reconstruction of GaAs(001) yielded CuInS{sub 2}(001) films featuring terraces. A deposition on 2 x 2 reconstructed GaAs(111)A surfaces led to a facetted CuInS{sub 2} surface. On sulphur-passivated non-reconstructed GaAs(111)B a deposition of chalcopyrite ordered CuInS{sub 2} free of facets was possible. On the surface of Cu-rich CuInS{sub 2} films CuS crystallites formed. This yields ARUPS spectra showing the electronic stucture of CuInS{sub 2} superimposed by non-dispergative states of the polycrystalline CuS segregations. The effective hole masses were derived from the k {sub vertical} {sub stroke} {sub vertical} {sub stroke} measurements. Finally the results of this work showed that the use of a (111) substrate leads to domain formation of the deposited CuInS{sub 2}(112) films. Thus ARUPS spectra of such films show a superposition of the band structures along different directions. (orig.)

  4. Correlation between electronic structure and energy band in Eu-doped CuInTe2 semiconductor compound with chalcopyrite structure

    Institute of Scientific and Technical Information of China (English)

    Tai Wang; Yong-Quan Guo; Shuai Li

    2017-01-01

    The Eu-doped Cu(In,Eu)Te2 semiconductors with chalcopyrite structures are promising materials for their applications in the absorption layer for thin-film solar cells due to their wider band-gaps and better optical properties than those of CulnTe2.In this paper,the Eu-doped CulnTe2 (Culn1-xEuxTe2,x =0,0.1,0.2,0.3) are studied systemically based on the empirical electron theory (EET).The studies cover crystal structures,bonding regularities,cohesive energies,energy levels,and valence electron structures.The theoretical values fit the experimental results very well.The physical mechanism of a broadened band-gap induced by Eu doping into CuInTe2 is the transitions between different hybridization energy levels induced by electron hopping between s and d orbitals and the transformations from the lattice electrons to valence electrons for Cu and In ions.The research results reveal that the photovoltaic effect induces the increase of lattice electrons of In and causes the electric resistivity to decrease.The Eu doping into CuInTe2 mainly influences the transition between different hybridization energy levels for Cu atoms,which shows that the 3d electron numbers of Cu atoms change before and after Eu doping.In single phase CuIn1-xEuxTe2,the number of valence electrons changes regularly with increasing Eu content,and the calculated band gap Eg also increases,which implies that the optical properties of Eu-doped CuIn1-xEuxTe2 are improved.

  5. Structural, elastic, electronic, bonding, and optical properties of BeAZ{sub 2} (A = Si, Ge, Sn; Z = P, As) chalcopyrites

    Energy Technology Data Exchange (ETDEWEB)

    Fahad, Shah [Department of Physics, Hazara University Mansehra, KPK, Mansehra (Pakistan); Murtaza, G., E-mail: murtaza@icp.edu.pk [Materials Modeling Laboratory, Department of Physics, Islamia College University, Peshawar (Pakistan); Ouahrani, T. [Laboratoire de Physique Théorique, B.P. 230, Université de Tlemcen, Tlemcen 13000 (Algeria); Ecole Préparatoire en Sciences et Techniques, BP 165 R.P., 13000 Tlemcen (Algeria); Khenata, R., E-mail: khenata_rabah@yahoo.fr [Laboratoire de Physique Quantique et de Modélisation Mathématique, Université de Mascara, 29000 (Algeria); Yousaf, Masood [Center for Multidimensional Carbon Materials, Institute for Basic Science, Department of Physics, Ulsan National Institute of Science and Technology, Ulsan 689-798 (Korea, Republic of); Omran, S.Bin [Department of Physics and Astronomy, College of Science, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia); Mohammad, Saleh [Department of Physics, Hazara University Mansehra, KPK, Mansehra (Pakistan)

    2015-10-15

    A first principles density functional theory (DFT) technique is used to study the structural, chemical bonding, electronic and optical properties of BeAZ{sub 2} (A = Si, Ge, Sn; Z = P, As) chalcopyrite materials. The calculated parameters are in good agreement with the available experimental results. The lattice constants and the equilibrium volume increased as we moved from Si to Ge to Sn, whereas the c/a and internal parameters u decreased by shifting the cation from P to As. These compounds are elastically stable. An investigation of the band gap using the WC-GGA, EV-GGA, PBE-GGA and mBJ-metaGGA potentials suggested that BeSiP{sub 2} and BeSiAs{sub 2} are direct band gap compounds, whereas BeGeP{sub 2,} BeGeAs{sub 2,} BeSnP{sub 2,} BeSnAs{sub 2} are indirect band gap compounds. The energy band gaps decreased by changing B from Si to Sn and increased by changing the anion C from P to As. The bonding among the cations and anions is primarily ionic. In the optical properties, the real and imaginary parts of the dielectric functions, reflectivity and optical conductivity have been studied over a wide energy range. - Highlights: • The compounds are studied by FP-LAPW method within mBJ approximation. • All of the studied materials show isotropic behaviour. • All the compounds show direct band gap nature. • Bonding nature is mostly covalent among the studied compounds. • High absorption peaks and reflectivity ensures there utility in optoelectronic devices.

  6. Classroom: Efficient Grading

    Science.gov (United States)

    Shaw, David D.; Pease, Leonard F., III.

    2014-01-01

    Grading can be accelerated to make time for more effective instruction. This article presents specific time management strategies selected to decrease administrative time required of faculty and teaching assistants, including a multiple answer multiple choice interface for exams, a three-tier grading system for open ended problem solving, and a…

  7. Grain Grading and Handling.

    Science.gov (United States)

    Rendleman, Matt; Legacy, James

    This publication provides an introduction to grain grading and handling for adult students in vocational and technical education programs. Organized in five chapters, the booklet provides a brief overview of the jobs performed at a grain elevator and of the techniques used to grade grain. The first chapter introduces the grain industry and…

  8. Vascular grading of angiogenesis

    DEFF Research Database (Denmark)

    Hansen, S; Grabau, D A; Sørensen, Flemming Brandt

    2000-01-01

    The study aimed to evaluate the prognostic value of angiogenesis by vascular grading of primary breast tumours, and to evaluate the prognostic impact of adding the vascular grade to the Nottingham Prognostic Index (NPI). The investigation included 836 patients. The median follow-up time was 11...... years and 4 months. The microvessels were immunohistochemically stained by antibodies against CD34. Angiogenesis was graded semiquantitatively by subjective scoring into three groups according to the expected number of microvessels in the most vascular tumour area. The vascular grading between observers...... for 24% of the patients, who had a shift in prognostic group, as compared to NPI, and implied a better prognostic dissemination. We concluded that the angiogenesis determined by vascular grading has independent prognostic value of clinical relevance for patients with breast cancer....

  9. Vascular grading of angiogenesis

    DEFF Research Database (Denmark)

    Hansen, S; Grabau, D A; Sørensen, Flemming Brandt

    2000-01-01

    The study aimed to evaluate the prognostic value of angiogenesis by vascular grading of primary breast tumours, and to evaluate the prognostic impact of adding the vascular grade to the Nottingham Prognostic Index (NPI). The investigation included 836 patients. The median follow-up time was 11...... years and 4 months. The microvessels were immunohistochemically stained by antibodies against CD34. Angiogenesis was graded semiquantitatively by subjective scoring into three groups according to the expected number of microvessels in the most vascular tumour area. The vascular grading between observers...... impact for 24% of the patients, who had a shift in prognostic group, as compared to NPI, and implied a better prognostic dissemination. We concluded that the angiogenesis determined by vascular grading has independent prognostic value of clinical relevance for patients with breast cancer....

  10. CRA Grade Inflation

    OpenAIRE

    Kenneth H. Thomas

    2000-01-01

    Community Reinvestment Act of 1977 (CRA) ratings and performance evaluations are the only bank and thrift exam findings disclosed by financial institution regulators. Inflation of CRA ratings has been alleged by community activists for two decades, but there has been no quantification or empirical investigation of grade inflation. Using a unique grade inflation methodology on actual ratings and evaluation data for 1,407 small banks and thrifts under the revised CRA regulations, this paper con...

  11. Functionally graded materials

    CERN Document Server

    Mahamood, Rasheedat Modupe

    2017-01-01

    This book presents the concept of functionally graded materials as well as their use and different fabrication processes. The authors describe the use of additive manufacturing technology for the production of very complex parts directly from the three dimension computer aided design of the part by adding material layer after layer. A case study is also presented in the book on the experimental analysis of functionally graded material using laser metal deposition process.

  12. Contractions from grading

    Science.gov (United States)

    Krishnan, Chethan; Raju, Avinash

    2018-04-01

    We note that large classes of contractions of algebras that arise in physics can be understood purely algebraically via identifying appropriate Zm-gradings (and their generalizations) on the parent algebra. This includes various types of flat space/Carroll limits of finite and infinite dimensional (A)dS algebras, as well as Galilean and Galilean conformal algebras. Our observations can be regarded as providing a natural context for the Grassmann approach of Krishnan et al. [J. High Energy Phys. 2014(3), 36]. We also introduce a related notion, which we call partial grading, that arises naturally in this context.

  13. Endangered Animals. Second Grade.

    Science.gov (United States)

    Popp, Marcia

    This second grade teaching unit centers on endangered animal species around the world. Questions addressed are: What is an endangered species? Why do animals become extinct? How do I feel about the problem? and What can I do? Students study the definition of endangered species and investigate whether it is a natural process. They explore topics…

  14. Calculating Student Grades.

    Science.gov (United States)

    Allswang, John M.

    1986-01-01

    This article provides two short microcomputer gradebook programs. The programs, written in BASIC for the IBM-PC and Apple II, provide statistical information about class performance and calculate grades either on a normal distribution or based on teacher-defined break points. (JDH)

  15. Grades as Information

    Science.gov (United States)

    Grant, Darren

    2007-01-01

    We determine how much observed student performance in microeconomics principles can be attributed, inferentially, to three kinds of student academic "productivity," the instructor, demographics, and unmeasurables. The empirical approach utilizes an ordered probit model that relates student performance in micro to grades in prior…

  16. First Grade Baseline Evaluation

    Science.gov (United States)

    Center for Innovation in Assessment (NJ1), 2013

    2013-01-01

    The First Grade Baseline Evaluation is an optional tool that can be used at the beginning of the school year to help teachers get to know the reading and language skills of each student. The evaluation is composed of seven screenings. Teachers may use the entire evaluation or choose to use those individual screenings that they find most beneficial…

  17. The Fifth Grade Classroom.

    Science.gov (United States)

    Hartman, Michael; And Others

    An interdisciplinary design project report investigates the relationship of the fifth grade educational facility to the student and teacher needs in light of human and environmental factors. The classroom, activity and teaching spaces are analyzed with regard to the educational curriculum. Specifications and design criteria concerning equipment…

  18. Cutting Class Harms Grades

    Science.gov (United States)

    Taylor, Lewis A., III

    2012-01-01

    An accessible business school population of undergraduate students was investigated in three independent, but related studies to determine effects on grades due to cutting class and failing to take advantage of optional reviews and study quizzes. It was hypothesized that cutting classes harms exam scores, attending preexam reviews helps exam…

  19. Inflated Grades, Enrollments & Budgets

    Directory of Open Access Journals (Sweden)

    J. E. Stone

    1995-06-01

    Full Text Available Reports of the past 13 years that call attention to deficient academic standards in American higher education are enumerated. Particular attention is given the Wingspread Group's recent An American Imperative: Higher Expectations for Higher Education. Low academic standards, grade inflation, and budgetary incentives for increased enrollment are analyzed and a call is made for research at the state level. Reported trends in achievement and GPAs are extrapolated to Tennessee and combined with local data to support the inference that 15% of the state's present day college graduates would not have earned a diploma by mid 1960s standards. A conspicuous lack of interest by public oversight bodies is noted despite a growing public awareness of low academic expectations and lenient grading and an implicit budgetary impact of over $100 million. Various academic policies and the dynamics of bureaucratic control are discussed in relationship to the maintenance of academic standards. The disincentives for challenging course requirements and responsible grading are examined, and the growing movement to address academic quality issues through better training and supervision of faculty are critiqued. Recommendations that would encourage renewed academic integrity and make learning outcomes visible to students, parents, employers, and the taxpaying public are offered and briefly discussed.

  20. A New Heterotrophic Strain for Bioleaching of Low Grade Complex Copper Ore

    Directory of Open Access Journals (Sweden)

    Kaijian Hu

    2016-02-01

    Full Text Available A new heterotrophic strain, named Providencia sp. JAT-1, was isolated and used in bioleaching of low-grade complex copper ore. The strain uses sodium citrate as a carbon source and urea as a nitrogen source to produce ammonia. The optimal growth condition of the strain is 30 C, initial pH 8, sodium citrate 10 g/L and urea 20 g/L, under which the cell density and ammonia concentration in the medium reached a maximum of 4.83 × 108 cells/mL and 14 g/L, respectively. Ammonia produced by the strain is used as the main lixiviant in bioleaching. Bioleaching results revealed that higher strain growth led to a higher copper recovery, while higher pulp density will cause a greater inhibitory effect on strain growth and ammonia production. The copper extraction reached the highest value of 54.5% at the pulp density of 1%. Malachite, chrysocolla and chalcocite are easy to leach out in this bioleaching system while chalcopyrite is difficult. Results of comparative leaching experiments show that bioleaching using JAT-1 is superior to ammonia leaching at the same condition. The metabolites produced by the strain other than ammonia are also involved in bioleaching.

  1. TCGA_LowerGradeGliomas

    Science.gov (United States)

    TCGA researchers analyzed nearly 300 cases of diffuse low- and intermediate-grade gliomas, which together comprise lower-grade gliomas. LGGs occur mainly in adults and include astrocytomas, oligodendrogliomas and oligoastrocytomas.

  2. Deposition and characterization of graded Cu(In{sub 1-x}Ga{sub x})Se{sub 2} thin films by spray pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Babu, B.J. [Department of Electrical Engineering-SEES, CINVESTAV-IPN, Avenida IPN 2508, San Pedro Zacatenco, D.F. C.P 07360 (Mexico); Institute of Molecules and Materials, UMR-CNRS 6283, Université du Maine, Avenue O. Messiaen, F-72085 Le Mans (France); Velumani, S., E-mail: velu@cinvestav.mx [Department of Electrical Engineering-SEES, CINVESTAV-IPN, Avenida IPN 2508, San Pedro Zacatenco, D.F. C.P 07360 (Mexico); College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kassiba, A. [Institute of Molecules and Materials, UMR-CNRS 6283, Université du Maine, Avenue O. Messiaen, F-72085 Le Mans (France); Asomoza, R. [Department of Electrical Engineering-SEES, CINVESTAV-IPN, Avenida IPN 2508, San Pedro Zacatenco, D.F. C.P 07360 (Mexico); Chavez-Carvayar, J.A. [Instituto Investigaciones en Materiales-UNAM, Ciudad Universitario, D.F.Mexico (Mexico); Yi, Junsin, E-mail: yi@yurim.skku.ac.kr [College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

    2015-07-15

    Cu(In{sub 1-x}Ga{sub x})Se{sub 2} (CIGS) thin films and their graded (x = 1 to 0) layer were grown on soda lime glass substrates using chemical spray pyrolysis (CSP) at different substrate temperatures (T{sub s}). After optimization of T{sub s}, depositions were carried out at different gallium composition (x) at optimized temperature of 350 °C. All the films deposited at T{sub s} ≥ 350 °C were polycrystalline chalcopyrite structure, with a preferential orientation of (112), including the graded layer. With increase in x, lattice parameters a and c were observed to decrease. Line scan of the CIGS layer showed intersection of gallium and indium concentrations, revealing the graded nature of the film. Composition dependence of Raman peak for CuInSe{sub 2} (CIS) deposited by CSP was analyzed. Optical transmittance at a wavelength of 800 nm of the film with x = 0 (CIS) (30%) was found lower than that of the film grown with x = 0.82 (CIGS) (50%). Cusp-shape of the resistivity was observed with an increase of x leading to steep rise in resistivity of the films (1.61–71.68 Ω-cm) till x = 0.42 and then decreased to 4.78 Ω-cm at x = 0.82. Carrier concentrations of the films were evaluated in the order of 10{sup 16}–10{sup 19} cm{sup −3} with p-type conductivity. These results indicate that graded CIGS thin films with modulated gallium composition can be prepared by CSP. - Graphical abstract: Display Omitted - Highlights: • Optimization of the spray deposition system for device grade chalcopyrite CIGS films. • Optimized substrate temperature to obtain single-phase CIGS by spray deposition. • Detailed report on compositional dependence of CuInSe{sub 2} (CIS) thin films. • Systematic analysis of the influence of Ga in CIS by spray deposition. • Bowing parameter is extracted from the experiment values.

  3. Let's End the Grading Game.

    Science.gov (United States)

    Edwards, Clifford H.; Edwards, Laurie

    1999-01-01

    Argues that grades have negative effects on learning and self-concept. States that while grading has a long tradition of sorting children for college entrance, there is limited evidence that grades serve a valid purpose. Argues that this practice should be abolished and an evaluation system established that provides a more valid estimate of…

  4. Four Steps in Grading Reform

    Science.gov (United States)

    Guskey, Thomas R.; Jung, Lee Ann

    2012-01-01

    The field of education is moving rapidly toward a standards-based approach to grading. School leaders have become increasingly aware of the tremendous variation that exists in grading practices, even among teachers of the same courses in the same department in the same school. Consequently, students' grades often have little relation to their…

  5. Functionally Graded Materials Database

    Science.gov (United States)

    Kisara, Katsuto; Konno, Tomomi; Niino, Masayuki

    2008-02-01

    Functionally Graded Materials Database (hereinafter referred to as FGMs Database) was open to the society via Internet in October 2002, and since then it has been managed by the Japan Aerospace Exploration Agency (JAXA). As of October 2006, the database includes 1,703 research information entries with 2,429 researchers data, 509 institution data and so on. Reading materials such as "Applicability of FGMs Technology to Space Plane" and "FGMs Application to Space Solar Power System (SSPS)" were prepared in FY 2004 and 2005, respectively. The English version of "FGMs Application to Space Solar Power System (SSPS)" is now under preparation. This present paper explains the FGMs Database, describing the research information data, the sitemap and how to use it. From the access analysis, user access results and users' interests are discussed.

  6. The Implications of Grade Inflation

    DEFF Research Database (Denmark)

    Smith, David E.; Fleisher, Steven

    2011-01-01

    The authors review current and past practices of the grade inflation controversy and present ways to return to each institution’s established grading guidelines. Students are graded based on knowledge gathered. Certain faculty members use thorough evaluative methods, such as written and oral pres...... have been profiled in the news. The model is provided to ensure that degree candidates are academic experts in their field, having earned the credential through rigorous study....

  7. Practicing Good Habits, Grade 4.

    Science.gov (United States)

    Van Cong Lau; And Others

    This illustrated textbook was designed for teaching civics and values to fourth grade students in Vietnam. It is divided into six chapters: (1) At School (recapitulation of the grade three program, friendship, respect for the teacher, team work, discipline, honor); (2) In the Street: Traffic Regulations; (3) At Home (the extended family spirit,…

  8. Graded geometry and Poisson reduction

    OpenAIRE

    Cattaneo, A S; Zambon, M

    2009-01-01

    The main result of [2] extends the Marsden-Ratiu reduction theorem [4] in Poisson geometry, and is proven by means of graded geometry. In this note we provide the background material about graded geometry necessary for the proof in [2]. Further, we provide an alternative algebraic proof for the main result. ©2009 American Institute of Physics

  9. Compositionally Graded Multilayer Ceramic Capacitors.

    Science.gov (United States)

    Song, Hyun-Cheol; Zhou, Jie E; Maurya, Deepam; Yan, Yongke; Wang, Yu U; Priya, Shashank

    2017-09-27

    Multilayer ceramic capacitors (MLCC) are widely used in consumer electronics. Here, we provide a transformative method for achieving high dielectric response and tunability over a wide temperature range through design of compositionally graded multilayer (CGML) architecture. Compositionally graded MLCCs were found to exhibit enhanced dielectric tunability (70%) along with small dielectric losses (filters and power converters.

  10. Effect of Grade Retention in First Grade on Psychosocial Outcomes

    OpenAIRE

    Wu, Wei; West, Stephen G.; Hughes, Jan N.

    2010-01-01

    In a 4-year longitudinal study, the authors investigated effects of retention in first grade on children’s externalizing and internalizing behaviors; social acceptance; and behavioral, cognitive, and affective engagement. From a large multiethnic sample (n = 784) of children below the median on literacy at school entrance, 124 retained children were matched with 251 promoted children on the basis of propensity scores (probability of being retained in first grade estimated from 72 baseline var...

  11. Gold grade of epithermal gold ore at Lamuntet, Brang Rea, West Sumbawa District, West Nusa Tenggara Province, Indonesia

    Science.gov (United States)

    Ernawati, Rika; Idrus, Arifudin; TBMP, Himawan

    2017-06-01

    Lamuntet is one of gold ore mining area carried out by the Artisanal Small scale Gold Mining (ASGM) located in West Sumbawa, Indonesia. Most of the miners at this area are not the local miners but also those from other regions. Mineralization of this area is strong identified as low sulfidation epithermal system. There are two blocks of this mining location, namely, Ngelampar block with an area of 0.164 km2 and Song block with an area of 0.067 km2. This study was focused on Ngelampar block. The characteristic of epithermal system is the existence of quartz vein with comb, vuggy, and sugary texture. The aim of this research was to analyze the gold grade and other metals, such as Cu, Ag, Pb, As, Zn, and Hg. The research methods included literature study from previous researches, field work, laboratory work, and interpretation. The literature study was performed on previous researches with similar study area. The field work comprised of direct observation and sampling. Fieldwork was done for a week to obtain gold ore/vein. Sixteen samples were analyzed to obtain the grade of ore/metal. The Hg laboratory analysis was then performed on the six samples with the highest gold grade. Laboratory works were conducted at Intertek Jakarta by using Fire Assay (FA) for gold grade and Atomic Absorption Spectrophotometry (AAS) for Cu, Ag, Pb, As, Zn, and Hg. Results of the analysis showed the range of Au was grade (0.1 ppm - 27.8 ppm), Cu was 26 ppm -1740 ppm, Pb was 101 ppm- >4000 ppm, Zn of 73 ppm- >10,000 ppm, Ag of 3 ppm -185 ppm, As was 150 ppm-6530 ppm, and Hg of 0.08 ppm - 1.89 ppm. L1 and L15 had high grade for all values (Au, Ag, Zn, Cu, As, and Hg). Gold mineralization was formed as electrum because of Ag content is higher than 20%. Associated minerals of the samples in the study area were galena, sphalerite, arsenopyrite, and chalcopyrite which showed the characteristic of rich base metal of Pb, Zn, and Cu at LS epithermal.

  12. The effects of mixtures of potassium amyl xanthate (PAX and isopropyl ethyl thionocarbamate (IPETC collectors on grade and recovery in the froth flotation of a nickel sulfide ore

    Directory of Open Access Journals (Sweden)

    Westhein Maree

    2017-12-01

    Full Text Available Potassium amyl xanthate (PAX and sodium isobutyl xanthate (SIBX are commonly used collectors in both the bulk and selective froth flotation of sulfide ores. These thiol xanthate collectors are conventionally mixed together as well as with more selective thiol collectors such as dithiophosphates (DTP and dithiocarbamates (DTC, in order to improve selectivity. With deteriorating nickel sulfide ores, more selective collectors and collector mixtures are desired for the efficient extraction of nickel. Thionocarbamates (TC are another group of thiol collectors used for selective froth flotation of sulfide minerals. Thionocarbamates are especially used in the selective froth flotation of chalcopyrite over pyrite and galena, but little is known about its selectivity with regards to nickel. Thionocarbamates are also more stable over larger pH ranges in comparison to xanthates and they possess beneficial frothing properties. This study compared the effects of using potassium amyl xanthate (PAX, isopropyl ethyl thionocarbamate (IPETC, sodium isobutyl xanthate (SIBX and their mixtures in the froth flotation of a pentlandite ore. In the mixtures of PAX or SIBX with IPETC, the xanthate accounted for 95.5 mol% and for the PAX and SIBX mixture a 50:50 mixture was used. This study showed that the highest cumulative nickel grades were obtained with PAX, SIBX and there mixture. The highest cumulative nickel recoveries were obtained with IPETC and its mixtures with PAX and SIBX (50–62%. Keywords: Nickel sulfide, Xanthate, Thionocarbamate, Grade, Recovery

  13. Gender discrimination in exam grading?

    DEFF Research Database (Denmark)

    Rangvid, Beatrice Schindler

    2018-01-01

    Girls, on average, obtain higher test scores in school than boys, and recent research suggests that part of this difference may be due to discrimination against boys in grading. This bias is consequential if admission to subsequent education programs is based on exam scores. This study assesses t...... tendencies are in accordance with statistical discrimination as a mechanism for grading bias in essay writing and with gender-stereotyped beliefs of math being a male domain....... are scored twice (blind and non-blind). Both strategies use difference-in-differences methods. Although imprecisely estimated, the point estimates indicate a blind grading advantage for boys in essay writing of approximately 5-8% SD, corresponding to 9-15% of the gender gap in essay exam grades. The effect...

  14. Progressive problems higher grade physics

    CERN Document Server

    Kennedy, William

    2001-01-01

    This book fully covers all three Units studied in Scotland's Higher Grade Physics course, providing a systematic array of problems (from the simplest to the most difficult) to lead variously abled pupils to examination success.

  15. Grade 6 Science Curriculum Specifications.

    Science.gov (United States)

    Alberta Dept. of Education, Edmonton. Curriculum Branch.

    This material describes curriculum specifications for grade 6 science in Alberta. Emphases recommended are: (1) process skills (50%); (2) psychomotor skills (10%); (3) attitudes (10%); and (4) subject matter (30%). Priorities within each category are identified. (YP)

  16. Improving GRADE evidence tables part 2

    DEFF Research Database (Denmark)

    Langendam, Miranda; Carrasco-Labra, Alonso; Santesso, Nancy

    2016-01-01

    OBJECTIVES: The Grading of Recommendations Assessment, Development, and Evaluation (GRADE) working group has developed GRADE evidence profiles (EP) and summary of findings (SoF) tables to present evidence summaries in systematic reviews, clinical guidelines, and health technology assessments. Exp...

  17. Cracks in functionally graded materials

    International Nuclear Information System (INIS)

    Bahr, H.-A.; Balke, H.; Fett, T.; Hofinger, I.; Kirchhoff, G.; Munz, D.; Neubrand, A.; Semenov, A.S.; Weiss, H.-J.; Yang, Y.Y.

    2003-01-01

    The weight function method is described to analyze the crack growth behavior in functionally graded materials and in particular materials with a rising crack growth resistance curve. Further, failure of graded thermal barrier coatings (TBCs) under cyclic surface heating by laser irradiation is modeled on the basis of fracture mechanics. The damage of both graded and non-graded TBCs is found to develop in several distinct stages: vertical cracking→delamination→blistering→spalling. This sequence can be understood as an effect of progressive shrinkage due to sintering and high-temperature creep during thermal cycling, which increases the energy-release rate for vertical cracks which subsequently turn into delamination cracks. The results of finite element modeling, taking into account the TBC damage mechanisms, are compatible with experimental data. An increase of interface fracture toughness due to grading and a decrease due to ageing have been measured in a four-point bending test modified by a stiffening layer. Correlation with the damage observed in cyclic heating is discussed. It is explained in which way grading is able to reduce the damage

  18. Graded/Gradient Porous Biomaterials

    Directory of Open Access Journals (Sweden)

    Xigeng Miao

    2009-12-01

    Full Text Available Biomaterials include bioceramics, biometals, biopolymers and biocomposites and they play important roles in the replacement and regeneration of human tissues. However, dense bioceramics and dense biometals pose the problem of stress shielding due to their high Young’s moduli compared to those of bones. On the other hand, porous biomaterials exhibit the potential of bone ingrowth, which will depend on porous parameters such as pore size, pore interconnectivity, and porosity. Unfortunately, a highly porous biomaterial results in poor mechanical properties. To optimise the mechanical and the biological properties, porous biomaterials with graded/gradient porosity, pores size, and/or composition have been developed. Graded/gradient porous biomaterials have many advantages over graded/gradient dense biomaterials and uniform or homogenous porous biomaterials. The internal pore surfaces of graded/gradient porous biomaterials can be modified with organic, inorganic, or biological coatings and the internal pores themselves can also be filled with biocompatible and biodegradable materials or living cells. However, graded/gradient porous biomaterials are generally more difficult to fabricate than uniform or homogenous porous biomaterials. With the development of cost-effective processing techniques, graded/gradient porous biomaterials can find wide applications in bone defect filling, implant fixation, bone replacement, drug delivery, and tissue engineering.

  19. Hardwood log grades and lumber grade yields for factory lumber logs

    Science.gov (United States)

    Leland F. Hanks; Glenn L. Gammon; Robert L. Brisbin; Everette D. Rast

    1980-01-01

    The USDA Forest Service Standard Grades for Hardwood Factory Lumber Logs are described, and lumber grade yields for 16 species and 2 species groups are presented by log grade and log diameter. The grades enable foresters, log buyers, and log sellers to select and grade those log suitable for conversion into standard factory grade lumber. By using the apropriate lumber...

  20. 7 CFR 810.2204 - Grades and grade requirements for wheat.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Grades and grade requirements for wheat. 810.2204... OFFICIAL UNITED STATES STANDARDS FOR GRAIN United States Standards for Wheat Principles Governing the Application of Standards § 810.2204 Grades and grade requirements for wheat. (a) Grades and grade requirements...

  1. Functionally Graded Mo sintered steels

    Directory of Open Access Journals (Sweden)

    Manuel Cisneros-Belmonte

    2016-12-01

    Full Text Available Functionally graded materials (FGM, the multi-materials, strive to satisfy the numerous requirements demanded of parts in a given combination of compositions and microstructures. The required material compatibility lead the manufacturing process and the achieving of an interface, not always diffuse. Powder metallurgy is one of the techniques used in manufacturing functionally graded materials, in particular the compaction matrix of the possible techniques for forming these materials. In this paper, a process of forming a functionally graded steel based on the use of a high molybdenum steel with cooper and other steel with copper, without molybdenum, is proposed with the aim of concentrating this element to the surface of the workpiece, increasing the mechanical strength. The study is completed with the evaluation of physical properties (density and porosity distribution, mechanical properties (hardness, tensile strength and elongation and microstructural analysis by optical and scanning electron microscopy.

  2. 7 CFR 51.304 - Combination grades.

    Science.gov (United States)

    2010-01-01

    ... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946... Standards for Grades of Apples Grades § 51.304 Combination grades. (a) Combinations of the above grades may...

  3. On-Demand Grades: The Effect of Online Grade Book Access on Student Mastery and Performance Goal Orientations, Grade Orientation, Academic Self Efficacy, and Grades

    Science.gov (United States)

    Seldow, Adam Lowell

    2010-01-01

    With the widespread growth of broadband Internet access, teachers, and in many cases, schools and school districts are transitioning from traditional paper-based grade books to student accessible online (Web-based) grade books. Online grade books offer students 24/7, on demand access to grades and various other student data, and have the potential…

  4. Functionally Graded Material: An overview

    CSIR Research Space (South Africa)

    Mahamood, RM

    2012-07-01

    Full Text Available -3146. [50] X. Jin, L. Wu, L. Guo, H. Yu, and Y. Sun, ?Experimental investigation of the mixed-mode crack propagation in ZrO2/NiCr functionally graded materials,? Engineering Fracture Mechanics, vol. 76(12), (2009), pp. 1800-1810. [51] Z. Cheng, D. Gao... by stable crack growth,? Engineering Fracture Mechanics, vol.72(15), (2005), pp. 2359-2372. [47] Z.-H. Jin, and R.H. Dodds Jr, ?Crack growth resistance behavior of a functionally graded material: computational studies,? Engineering Fracture Mechanics...

  5. On the union of graded prime ideals

    Directory of Open Access Journals (Sweden)

    Uregen Rabia Nagehan

    2016-01-01

    Full Text Available In this paper we investigate graded compactly packed rings, which is defined as; if any graded ideal I of R is contained in the union of a family of graded prime ideals of R, then I is actually contained in one of the graded prime ideals of the family. We give some characterizations of graded compactly packed rings. Further, we examine this property on h – Spec(R. We also define a generalization of graded compactly packed rings, the graded coprimely packed rings. We show that R is a graded compactly packed ring if and only if R is a graded coprimely packed ring whenever R be a graded integral domain and h – dim R = 1.

  6. 7 CFR 810.404 - Grades and grade requirements for corn.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Grades and grade requirements for corn. 810.404... OFFICIAL UNITED STATES STANDARDS FOR GRAIN United States Standards for Corn Principles Governing the Application of Standards § 810.404 Grades and grade requirements for corn. Grade Minimum test weight per...

  7. 7 CFR 810.1804 - Grades and grade requirements for sunflower seed.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Grades and grade requirements for sunflower seed. 810... AGRICULTURE OFFICIAL UNITED STATES STANDARDS FOR GRAIN United States Standards for Sunflower Seed Principles Governing the Application of Standards § 810.1804 Grades and grade requirements for sunflower seed. Grade...

  8. Attendance Policies and Student Grades

    Science.gov (United States)

    Risen, D. Michael

    2007-01-01

    The details described in this case study examine the issues related to attendance policies and how such policies might be legally used to affect student grades. Concepts discussed should cause graduate students in educational administration to reflect on the issues presented from various points of view when the students complete an analysis of the…

  9. Grading Rubrics: Hoopla or Help?

    Science.gov (United States)

    Howell, Rebecca J.

    2014-01-01

    The purpose of the study was to offer some quantitative, multivariate evidence concerning the impact of grading rubric use on academic outcome among American higher education students. Using a pre-post, quasi-experimental research design, cross-sectional data were derived from undergraduates enrolled in an elective during spring and fall 2009 at…

  10. Transportation: Grade 8. Cluster IV.

    Science.gov (United States)

    Calhoun, Olivia H.

    A curriculum guide for grade 8, the document is devoted to the occupational cluster "Transportation." It is divided into five units: surface transportation, interstate transportation, air transportation, water transportation, and subterranean transportation (the Metro). Each unit is introduced by a statement of the topic, the unit's…

  11. Smartphone-based grading of apple quality

    Science.gov (United States)

    Li, Xianglin; Li, Ting

    2018-02-01

    Apple quality grading is a critical issue in apple industry which is one economical pillar of many countries. Artificial grading is inefficient and of poor accuracy. Here we proposed to develop a portable, convenient, real-time, and low cost method aimed at grading apple. Color images of the apples were collected with a smartphone and the grade of sampled apple was assessed by a customized smartphone app, which offered the functions translating RGB color values of the apple to color grade and translating the edge of apple image to weight grade. The algorithms are based on modeling with a large number of apple image at different grades. The apple grade data evaluated by the smartphone are in accordance with the actual data. This study demonstrated the potential of smart phone in apple quality grading/online monitoring at gathering and transportation stage for apple industry.

  12. Elastic, vibration and thermodynamic properties of Cu1‑x Ag x InTe2 (x = 0, 0.25, 0.5, 0.75 and 1) chalcopyrite compounds via first principles

    Science.gov (United States)

    Zhong, Yuhan; Wang, Peida; Mei, Huayue; Jia, Zhenyuan; Cheng, Nanpu

    2018-06-01

    CuInTe2 chalcopyrite compound is widely used in the fields of optoelectronics and pyroelectricity, and doping atoms can further improve the physical properties of the CuInTe2 compound. For all we know, this is the first time that the elastic behaviors and lattice dynamical properties of Ag-doped CuInTe2 compounds with the tetragonal system are determined theoretically. The elastic, lattice dynamical and thermal properties of Cu1‑x Ag x InTe2 (x = 0, 0.25, 0.5, 0.75 and 1) compounds have been investigated by using density functional theory. The obtained elastic constants of Cu1‑x Ag x InTe2 compounds indicate that these compounds are mechanically stable and elastic anisotropic. The anisotropy of the {001} plane is more obvious than those of the {100} and {010} planes. Additionally, with increasing Ag doping concentrations, the bulk and shear moduli of Cu1‑x Ag x InTe2 compounds decrease and their toughness improves. The phonon spectra and density of states reveal that Cu (or Ag) atoms in Cu1‑x Ag x InTe2 compounds form chemical bonds with Te atoms, and Cu-Te bonds are gradually replaced by Ag-Te bonds with increasing Ag doping concentration. Vibration modes of Cu1‑x Ag x InTe2 compounds at the {{Γ }} point in the Brillouin zone show that each Cu1‑x Ag x InTe2 (x = 0 and 1) crystal includes five irreducible representations (A1, A2, B1, B2 and E). As for Cu1‑x Ag x InTe2 (x = 0.25, 0.5 and 0.75) compounds, each crystal has three irreducible representations (A, B and E). The atomic displacements of several typical phonon modes in CuInTe2 crystals have been analyzed to deepen the understanding of lattice vibrations in Cu1‑x AgxInTe2 compounds. With increasing Ag doping concentration, the Debye temperatures of Cu1‑x Ag x InTe2 compounds decrease, while their heat capacities increase.

  13. Anaplasia and grading in medulloblastomas.

    Science.gov (United States)

    Eberhart, Charles G; Burger, Peter C

    2003-07-01

    The variable clinical outcomes of medulloblastoma patients have prompted a search for markers with which to tailor therapies to individuals. In this review, we discuss clinical, histological and molecular features that can be used in such treatment customization, focusing on how histopathological grading can impact both patient care and research on the molecular basis of CNS embryonal tumors. Medulloblastomas span a histological spectrum ending in overtly malignant large cell/anaplastic lesions characterized by increased nuclear size, marked cytological anaplasia, and increased mitotic and apoptotic rates. These "high-grade" lesions make up approximately one quarter of medulloblastomas, and recur and metastasize more frequently than tumors lacking anaplasia. We believe anaplastic change represents a type of malignant progression common to many medulloblastoma subtypes and to other CNS embryonal lesions as well. Correlation of these histological changes with the accumulation of genetic events suggests a model for the histological and molecular progression of medulloblastoma.

  14. Gradings on simple Lie algebras

    CERN Document Server

    Elduque, Alberto

    2013-01-01

    Gradings are ubiquitous in the theory of Lie algebras, from the root space decomposition of a complex semisimple Lie algebra relative to a Cartan subalgebra to the beautiful Dempwolff decomposition of E_8 as a direct sum of thirty-one Cartan subalgebras. This monograph is a self-contained exposition of the classification of gradings by arbitrary groups on classical simple Lie algebras over algebraically closed fields of characteristic not equal to 2 as well as on some nonclassical simple Lie algebras in positive characteristic. Other important algebras also enter the stage: matrix algebras, the octonions, and the Albert algebra. Most of the presented results are recent and have not yet appeared in book form. This work can be used as a textbook for graduate students or as a reference for researchers in Lie theory and neighboring areas.

  15. Grading of quality assurance requirements

    International Nuclear Information System (INIS)

    1991-01-01

    The present Manual provides guidance and illustrative examples for applying a method by which graded quality assurance requirements may be determined and adapted to the items and services of a nuclear power plant in conformance with the requirements of the IAEA Nuclear Safety Standards (NUSS) Code and Safety Guides on quality assurance. The Manual replaces the previous publication IAEA-TECDOC-303 on the same subject. Various methods of grading quality assurance are available in a number of Member States. During the development of the present Manual it was not considered practical to attempt to resolve the differences between those methods and it was preferred to identify and benefit from the good practices available in all the methods. The method presented in this Manual deals with the aspects of management, documentation, control, verification and administration which affect quality. 1 fig., 4 tabs

  16. Grade Expectations: Rationality and Overconfidence

    Science.gov (United States)

    Magnus, Jan R.; Peresetsky, Anatoly A.

    2018-01-01

    Confidence and overconfidence are essential aspects of human nature, but measuring (over)confidence is not easy. Our approach is to consider students' forecasts of their exam grades. Part of a student's grade expectation is based on the student's previous academic achievements; what remains can be interpreted as (over)confidence. Our results are based on a sample of about 500 second-year undergraduate students enrolled in a statistics course in Moscow. The course contains three exams and each student produces a forecast for each of the three exams. Our models allow us to estimate overconfidence quantitatively. Using these models we find that students' expectations are not rational and that most students are overconfident, in agreement with the general literature. Less obvious is that overconfidence helps: given the same academic achievement students with larger confidence obtain higher exam grades. Female students are less overconfident than male students, their forecasts are more rational, and they are also faster learners in the sense that they adjust their expectations more rapidly. PMID:29375449

  17. Grade Expectations: Rationality and Overconfidence

    Directory of Open Access Journals (Sweden)

    Jan R. Magnus

    2018-01-01

    Full Text Available Confidence and overconfidence are essential aspects of human nature, but measuring (overconfidence is not easy. Our approach is to consider students' forecasts of their exam grades. Part of a student's grade expectation is based on the student's previous academic achievements; what remains can be interpreted as (overconfidence. Our results are based on a sample of about 500 second-year undergraduate students enrolled in a statistics course in Moscow. The course contains three exams and each student produces a forecast for each of the three exams. Our models allow us to estimate overconfidence quantitatively. Using these models we find that students' expectations are not rational and that most students are overconfident, in agreement with the general literature. Less obvious is that overconfidence helps: given the same academic achievement students with larger confidence obtain higher exam grades. Female students are less overconfident than male students, their forecasts are more rational, and they are also faster learners in the sense that they adjust their expectations more rapidly.

  18. Measure of uncertainty in regional grade variability

    NARCIS (Netherlands)

    Tutmez, B.; Kaymak, U.; Melin, P.; Castillo, O.; Gomez Ramirez, E.; Kacprzyk, J.; Pedrycz, W.

    2007-01-01

    Because the geological events are neither homogeneous nor isotropic, the geological investigations are characterized by particularly high uncertainties. This paper presents a hybrid methodology for measuring of uncertainty in regional grade variability. In order to evaluate the fuzziness in grade

  19. The grading management of the quality assurance

    International Nuclear Information System (INIS)

    Ma Xiaozheng; Han Shufang; Yu Bei; Tian Xuehang

    2009-01-01

    This paper introduces the quality assurance grading management of the items, services and technology process on nuclear power plants (nuclear island, conventional island, BOP), such as the requirements and aim in the related code, guide, technical document, the requirements for the related units, the grading principle and grading, the considering method for the differences of QA requirements of the each QA grand, as well as the status and propositions in the QA grading management in China. (authors)

  20. The pathologist's mean grade is constant and individualizes the prognostic value of bladder cancer grading.

    Science.gov (United States)

    van Rhijn, Bas W G; van Leenders, Geert J L H; Ooms, Bert C M; Kirkels, Wim J; Zlotta, Alexandre R; Boevé, Egbert R; Jöbsis, Adriaan C; van der Kwast, Theo H

    2010-06-01

    A new grading system for bladder cancer (BCa) was adopted in 2004 to reduce observer variability and provide better prognostic information. We compared the World Health Organization (WHO) 1973 and 2004 systems for observer variability and prognosis. Slides of 173 primary non-muscle-invasive BCa were reviewed two times by four pathologists. Intra- and interobserver variability were assessed using κ statistics. We determined the mean grade (eg, G1/low malignant potential is 1 grade point, G2/low grade is 2 grade points) of the pathologists per grading cycle. Kaplan-Meier analyses were applied for prediction of recurrence and progression. For WHO 2004 and 1973 grading, the agreement between the pathologists was 39-74% (κ: 0.14-0.58) and 39-64% (κ: 0.15-0.41), respectively. The intraobserver agreement varied from 71% to 88% (κ: 0.55-0.81). The mean grade of a pathologist was constant (difference below 0.1 grade point) irrespective of the grading system. Conversely, mean-grade differences among the pathologists were high, up to 0.7 grade point. The mean grades for the WHO 2004 system were 0.3-0.5 grade point higher than those of WHO 1973. Mean grade distinguished low and high graders among the pathologists and was strongly linked with risk of progression in each grade category. The variation in mean grade among individual pathologists exceeded the grade shift caused by WHO 2004 grading. Knowledge of the pathologist's mean grade allows a better assessment of the prognostic value of grading. Mean grade has the potential to become a tool for quality assurance in pathology. Copyright © 2009 European Association of Urology. Published by Elsevier B.V. All rights reserved.

  1. Examining Text Complexity in the Early Grades

    Science.gov (United States)

    Fitzgerald, Jill; Elmore, Jeff; Hiebert, Elfrieda H.; Koons, Heather H.; Bowen, Kimberly; Sanford-Moore, Eleanor E.; Stenner, A. Jackson

    2016-01-01

    The Common Core raises the stature of texts to new heights, creating a hubbub. The fuss is especially messy at the early grades, where children are expected to read more complex texts than in the past. But early-grades teachers have been given little actionable guidance about text complexity. The authors recently examined early-grades texts to…

  2. Registration Patterns Under Two Different Grading Systems.

    Science.gov (United States)

    Remley, Audrey W.

    In the early 1960's, Westminster College adopted a new grading system, with the traditional grade levels of A, B, C, D, and F converted to DN (Distinction), HP (High Pass), P (Pass), and NC (No Credit). NC replaced both D and F of the old system, and grade point averages were abolished, in an effort to encourage students to register in more…

  3. Forecasting and recruitment in graded manpower systems

    NARCIS (Netherlands)

    van Nunen, J.A.E.E.; Wessels, J.

    1977-01-01

    In this paper a generalized Markov model is introduced to describe the dynamic behaviour of an individual employee in a graded Manpower system. Characteristics like the employee's grade, his educational level, his age and the time spent in his actual grade, can be incorporated in the Markov model.

  4. Demystify Learning Expectations to Address Grade Inflation

    Science.gov (United States)

    Hodges, Linda C.

    2014-01-01

    This article describes the subject of "grade inflation," a reference to educators giving higher grades to student work than their expectations for student achievement warrant. Of the many reasons why this practice happens, Hodges specifically discusses inflating grades as "a natural consequence" when the faculty really…

  5. Grade Inflation: An Issue for Higher Education?

    Science.gov (United States)

    Caruth, Donald L.; Caruth, Gail D.

    2013-01-01

    Grade inflation impacts university credibility, student courses of study, choices of institution, and other areas. There has been an upward shift in grades without a corresponding upward shift in knowledge gained. Some of the most frequently mentioned causes of grade inflation are: (1) student evaluations of professors; (2) student teacher…

  6. Does Education Corrupt? Theories of Grade Inflation

    Science.gov (United States)

    Oleinik, Anton

    2009-01-01

    Several theories of grade inflation are discussed in this review article. It is argued that grade inflation results from the substitution of criteria specific to the search for truth by criteria of quality control generated outside of academia. Particular mechanisms of the grade inflation that occurs when a university is transformed into a…

  7. Characterizations of Some Semi magnetic Chalcopyrite Compounds

    International Nuclear Information System (INIS)

    Farrag, A.A.A.

    2012-01-01

    Cd 1-x Zn x Se (x=0, 0.5 and 1) and Cd 0.5 Zn 0.5 X 0.02 Se (X= Mn, Fe and Co) semiconductor and semi magnetic semiconductor compounds were prepared in the bulk form by melt quenching technique in ice water. Thin films of thickness 300 nm have been deposited on ultra cleaned soda lime glass substrates, at room temperature by thermal evaporation technique. The structural, optical and electrical properties of Cd 1-x Zn x Se (x=0, 0.5 and 1) and Cd 0.5 Zn 0.5 X 0.02 Se (X= Mn, Fe and Co) thin film samples have been studied. ESR and magnetic properties of Cd 0.5 Zn 0.5 X 0.02 Se (X= Mn, Fe and Co) powder samples also have been studied. The structural properties of Cd 1-x Zn x Se (x=0, 0.5 and 1) and Cd 0.5 Zn 0.5 X 0.02 Se (X= Mn, Fe and Co) thin film and powder samples have been investigated by using X-ray diffraction (XRD) technique. The crystal structure, lattice parameters, grain size, micro strain and dislocation density were determined from the X- ray diffraction patterns of the investigated samples. The optical properties of the investigated thin film samples were studied. Transmittance and reflectance were measured in wavelength range from 400 nm to 2500 nm and used to calculate the optical constants like absorption coefficient, refractive index and optical band gap. The obtained values of the optical band gap illustrated that the films exhibit direct band gap. The analysis of the obtained values of the refractive index yielded the high frequency dielectric constant and other optical dispersion parameters. The photon energy dependence of the relaxation time, dissipation factor and optical conductivity of the investigated thin film samples were studied also. The temperature dependence of dc conductivity for the investigated thin films was studied in temperature range from 300 K to 420 K. The obtained results showed that there are two different conduction mechanisms with two different values of activation energy in the defined temperature range. The temperature dependence of Hall coefficient RH for the thin film samples was studied in temperature range from 300 K to 420 K and in constant applied magnetic field (3.2 kG). The Hall coefficient of all thin film samples decreases with the temperature in opposite to that of the dc conductivity except for Cd 0.5 Zn 0.5 Co 0.02 Se; RH increases in high temperature. All of semiconductor thin films were n-type semiconductors. The Hall mobility increases with increase the temperature this means that the charge carrier mobility within the grains increases with the increase of temperature. The transverse magnetoresistance TMR of the investigated thin film samples was investigated in magnetic field range (0-3.2 k G) and in temperature range (300-420 K). It has been observed from the obtained results that the TMR for all films are negative at high temperatures and positive at lower temperatures. Also TMR magnitude increases with increasing the magnetic field and temperature but it is irregular. The ac conductivity as a function of temperature at different frequencies in temperature range from 300 K to 420 K and frequency range from 80 Hz to 5 MHz for the investigated thin films was studied. It is clear from the obtained results that σac(ω) is slightly temperature and frequency dependant. The temperature dependence decreases as ω increases, while increases at higher temperatures and lower frequencies. AC conductivity increases linearly with frequency according to the power relation . The obtained values of s as a function of temperature for the investigated thin films can be explained on the basis of the CBH model between centers forming IVAP'S proposed by Elliott. The dielectric constant and dielectric loss increase with the temperature and decrease with the frequency. The maximum barrier height was calculated according to Guintini equation at different temperatures. The relaxation time, resistance and σ ac ω = Aω capacitance were calculated from the Nyquist diagram. The behavior can be modeled by an equivalent parallel RC circuit for all investigated thin film samples. The ESR spectra of the Cd 0.5 Zn 0.5 X 0.02 Se (X= Mn, Fe and Co) powder samples were studied at room temperature. The obtained results showed that all samples were paramagnetic materials at the room temperature. The g-factor and concentration of paramagnetic defects were determined. The magnetic properties (hysteresis loops and ZFC/FC curves) were studied in temperature range from 5 K to 200 K. The obtained results indicated the ferromagnetic exchange interaction between the magnetic ions in case of Cd 0.5 Zn 0.5 Fe 0.02 Se and Cd 0.5 Zn 0.5 Co 0.02 Se but did not indicate conventional ferromagnetism, samples exhibit spin-glass behavior and also indicated antiferromagnetic interaction between Mn 2+ ions in case of Cd 0.5 Zn 0.5 Mn 0.02 Se sample.

  8. ANALYSIS OF A DATA BASE OF CHALCOPYRITE ...

    African Journals Online (AJOL)

    31 déc. 2011 ... physique, Unité de Recherche sur les Matériaux Energies Renouvelables, B.P 119, .... estimé par l'équation proposée suivante. B .... caractéristiques d'un ensemble de données n'est évidemment pas une fin en soi, mais cet.

  9. The Relationship of Grade Span in 9th Grade to Math Achievement in High School

    Science.gov (United States)

    West, John; Miller, Mary Lou; Myers, Jim; Norton, Timothy

    2015-01-01

    Purpose, Scope, and Method of Study: The purpose of this study was to determine if a correlation exists between grade span for ninth grade and gains in math achievement test scores in 10th grade and 12th grade. A quantitative, longitudinal, correlational research design was employed to investigate the research questions. The population was high…

  10. High grade glioma: Imaging combined with pathological grade defines management and predicts prognosis

    International Nuclear Information System (INIS)

    Burnet, Neil G.; Lynch, Andrew G.; Jefferies, Sarah J.; Price, Stephen J.; Jones, Phil H.; Antoun, Nagui M.; Xuereb, John H.; Pohl, Ute

    2007-01-01

    Introduction: There is ambiguity in pathological grading of high grade gliomas within the WHO 2000 classification, especially those with predominant oligodendroglial differentiation. Patients and methods: All adult high grade gliomas treated radically, 1996-2005, were assessed. Cases in which pathology was grade III but radiology suggested glioblastoma (GBM) were classified as 'grade III/IV'; their pathology was reviewed. Results: Data from 245 patients (52 grade III, 18 grade III/IV, 175 GBM) were analysed using a Cox Proportional Hazards model. On pathology review, features suggestive of more aggressive behaviour were found in all 18 grade III/IV tumours. Oligodendroglial components with both necrosis and microvascular proliferation were present in 7. MIB-1 counts for the last 8 were all above 14%, mean 27%. Median survivals were: grade III 34 months, grade III/IV 10 months, GBM 11 months. Survival was not significantly different between grade III/IV and GBM. Patients with grade III/IV tumours had significantly worse outcome than grade III, with a hazard of death 3.7 times higher. Conclusions: The results highlight the current inconsistency in pathological grading of high grade tumours, especially those with oligodendroglial elements. Patients with histological grade III tumours but radiological appearances suggestive of GBM should be managed as glioblastoma

  11. Association of Grade Configuration with School Climate for 7th and 8th Grade Students

    Science.gov (United States)

    Malone, Marisa; Cornell, Dewey; Shukla, Kathan

    2017-01-01

    Educational authorities have questioned whether middle schools provide the best school climate for 7th and 8th grade students, and proposed that other grade configurations such as K-8th grade schools may provide a better learning environment. The purpose of this study was to compare 7th and 8th grade students' perceptions of 4 key features of…

  12. Comparing Dropout Predictors for Two State-Level Panels Using Grade 6 and Grade 8 Data

    Science.gov (United States)

    Franklin, Bobby J.; Trouard, Stephen B.

    2016-01-01

    The purpose of this study was to examine the effectiveness of dropout predictors across time. Two state-level high school graduation panels were selected to begin with the seventh and ninth grades but end at the same time. The first panel (seventh grade) contained 29,554 students and used sixth grade predictors. The second panel (ninth grade)…

  13. Grade Inflation Marches On: Grade Increases from the 1990s to 2000s

    Science.gov (United States)

    Kostal, Jack W.; Kuncel, Nathan R.; Sackett, Paul R.

    2016-01-01

    Grade inflation threatens the integrity of college grades as indicators of academic achievement. In this study, we contribute to the literature on grade inflation by providing the first estimate of the size of grade increases at the student level between the mid-1990s and mid-2000s. By controlling for student characteristics and course-taking…

  14. The effect of various grading scales on student grade point averages.

    Science.gov (United States)

    Barnes, Kelli D; Buring, Shauna M

    2012-04-10

    To investigate changes in and the impact of grading scales from 2005 to 2010 and explore pharmacy faculty and student perceptions of whole-letter and plus/minus grading scales on cumulative grade point averages (GPAs) in required courses. Grading scales used in 2010 at the University of Cincinnati College of Pharmacy were retrospectively identified and compared to those used in 2005. Mean GPA was calculated using a whole-letter grading scale and a plus/minus grading scale to determine the impact of scales on GPA. Faculty members and students were surveyed regarding their perceptions of plus/minus grading. Nine unique grading scales were used throughout the curriculum, including plus/minus (64%) and whole-letter (21%) grading scales. From 2005 to 2010 there was transition from use of predominantly whole-letter scales to plus/minus grading scales. The type of grading scale used did not affect the mean cumulative GPA. Students preferred use of a plus-only grading scale while faculty members preferred use of a plus/minus grading scale. The transition from whole-letter grading to plus/minus grading in courses from 2005 to 2010 reflects pharmacy faculty members' perception that plus/minus grading allows for better differentiation between students' performances.

  15. Composition and Redox Potential of High-Grade Fluids: An Example from the Nilgiri Block, Southern India

    Science.gov (United States)

    Samuel, V. O.; Harlov, D. E.; Kwon, S.

    2017-12-01

    Composition and redox potential of fluids present during high-grade metamorphism exert an enormous influence on mineral textures and their regional trends within metamorphic complexes. We examine silicate, oxide, and sulfide trends in the Nilgiri Block, southern India. This terrain formed through subduction-related arc magmatic processes in the Neoarchean (ca. 2500 Ma). The Nilgiri highlands are characterized by granulite-facies metagabbro in the north, a two-pyroxene granulite transition zone, and tonalitic-granodioritic charnockites in the central and southern part. Garnet-orthopyroxene and orthopyroxene-clinopyroxene thermometry and garnet-orthopyroxene-plagioclase-quartz barometric results indicate a regional trend both in temperature ( 650 to 800 °C) and in pressure (700 to 1100 MPa) from SW to NE across the Nilgiri highlands. Regional trends are also seen in the oxide-sulfide mineralogy. The main oxide assemblage in the charnockites is rutile-ilmenite, whereas in the two-pyroxene granulites and metagabbros, hemo-ilmenite-magnetite dominates. The key sulfide mineral in the charnockites is pyrrhotite, with minor chalcopyrite. In the two-pyroxene granulites and metagabbros, the principle sulfide assemblage is pyrite +/- minor pyrrhotite. This reveals a regional oxidation trend. The metagabbros and two-pyroxene granulites are highly oxidized compared to the charnockites. Their higher oxidation state is proposed to be the result of highly oxidizing agents (probably as SO2) in low H2O activity fluids (most likely concentrated NaCl brines) during granulite-facies metamorphism of the metagabbros and two-pyroxene granulites. These agents were considerably more reducing (possibly as H2S) during granulite-facies metamorphism of the charnockites. This study emphasizes the potential role of oxidizing and reducing, low H2O activity fluids during granulite-facies metamorphism.

  16. Is the Sky Falling? Grade Inflation and the Signaling Power of Grades.

    Science.gov (United States)

    Pattison, Evangeleen; Grodsky, Eric; Muller, Chandra

    2013-06-01

    Grades are the fundamental currency of our educational system; they signal academic achievement and non-cognitive skills to parents, employers, postsecondary gatekeepers, and students themselves. Grade inflation compromises the signaling value of grades, undermining their capacity to achieve the functions for which they are intended. We challenge the 'increases in grade point average' definition of grade inflation and argue that grade inflation must be understood in terms of the signaling power of grades. Analyzing data from four nationally representative samples, we find that in the decades following 1972: (a) grades have risen at high schools and dropped at four-year colleges, in general, and selective four-year institutions, in particular; and (b) the signaling power of grades has attenuated little, if at all.

  17. Production of Food Grade Yeasts

    Directory of Open Access Journals (Sweden)

    Argyro Bekatorou

    2006-01-01

    Full Text Available Yeasts have been known to humans for thousands of years as they have been used in traditional fermentation processes like wine, beer and bread making. Today, yeasts are also used as alternative sources of high nutritional value proteins, enzymes and vitamins, and have numerous applications in the health food industry as food additives, conditioners and flavouring agents, for the production of microbiology media and extracts, as well as livestock feeds. Modern scientific advances allow the isolation, construction and industrial production of new yeast strains to satisfy the specific demands of the food industry. Types of commercial food grade yeasts, industrial production processes and raw materials are highlighted. Aspects of yeast metabolism, with respect to carbohydrate utilization, nutritional aspects and recent research advances are also discussed.

  18. Processing of low-grade uranium ores

    International Nuclear Information System (INIS)

    Michel, P.

    1975-01-01

    Four types of low grade ores are studied. Low grade ores which must be extracted because they are enclosed in a normal grade deposit. Heap leaching is the processing method which is largely used. It allows to obtain solutions or preconcentrates which may be delivered at the nearest plant. Normal grade ores contained in a low amplitude deposit which can be processed using leaching as far as the operation does not need any large expensive equipment. Medium grade ores in medium amplitude deposits to which a simplified conventional process can be applied using fast heap leaching. Low grade ores in large deposits. The processing possibilities leading to use in place leaching are explained. The operating conditions of the method are studied (leaching agent, preparation of the ore deposit to obtain a good tightness with regard to the hydrological system and to have a good contact between ore and reagent) [fr

  19. Processing of low grade uranium ores

    International Nuclear Information System (INIS)

    Michel, P.

    1978-10-01

    Four types of low-grade ores are studied: (1) Low-grade ores that must be extracted because they are enclosed in a normal-grade deposit. Heap leaching is the processing method which is largely used. (2) Normal-grade ores contained in low-amplitude deposits. They can be processed using in-place leaching as far as the operation does not need any large and expensive equipment. (3) Medium-grade ores in medium-amplitude deposits. A simplified conventional process can be applied using fast heap leaching. (4) Low-grade ores in large deposits. The report explains processing possibilities leading in most cases to the use of in-place leaching. The operating conditions of this method are laid out, especially the selection of the leaching agents and the preparation of the ore deposit

  20. MRI differentiation of low-grade from high-grade appendicular chondrosarcoma

    International Nuclear Information System (INIS)

    Douis, Hassan; Singh, Leanne; Saifuddin, Asif

    2014-01-01

    To identify magnetic resonance imaging (MRI) features which differentiate low-grade chondral lesions (atypical cartilaginous tumours/grade 1 chondrosarcoma) from high-grade chondrosarcomas (grade 2, grade 3 and dedifferentiated chondrosarcoma) of the major long bones. We identified all patients treated for central atypical cartilaginous tumours and central chondrosarcoma of major long bones (humerus, femur, tibia) over a 13-year period. The MRI studies were assessed for the following features: bone marrow oedema, soft tissue oedema, bone expansion, cortical thickening, cortical destruction, active periostitis, soft tissue mass and tumour length. The MRI-features were compared with the histopathological tumour grading using univariate, multivariate logistic regression and receiver operating characteristic curve (ROC) analyses. One hundred and seventy-nine tumours were included in this retrospective study. There were 28 atypical cartilaginous tumours, 79 grade 1 chondrosarcomas, 36 grade 2 chondrosarcomas, 13 grade 3 chondrosarcomas and 23 dedifferentiated chondrosarcomas. Multivariate analysis demonstrated that bone expansion (P = 0.001), active periostitis (P = 0.001), soft tissue mass (P < 0.001) and tumour length (P < 0.001) were statistically significant differentiating factors between low-grade and high-grade chondral lesions with an area under the ROC curve of 0.956. On MRI, bone expansion, active periostitis, soft tissue mass and tumour length can reliably differentiate high-grade chondrosarcomas from low-grade chondral lesions of the major long bones. (orig.)

  1. MRI differentiation of low-grade from high-grade appendicular chondrosarcoma

    Energy Technology Data Exchange (ETDEWEB)

    Douis, Hassan; Singh, Leanne; Saifuddin, Asif [The Royal National Orthopaedic Hospital NHS Trust, Department of Radiology, Stanmore, Middlesex (United Kingdom)

    2014-01-15

    To identify magnetic resonance imaging (MRI) features which differentiate low-grade chondral lesions (atypical cartilaginous tumours/grade 1 chondrosarcoma) from high-grade chondrosarcomas (grade 2, grade 3 and dedifferentiated chondrosarcoma) of the major long bones. We identified all patients treated for central atypical cartilaginous tumours and central chondrosarcoma of major long bones (humerus, femur, tibia) over a 13-year period. The MRI studies were assessed for the following features: bone marrow oedema, soft tissue oedema, bone expansion, cortical thickening, cortical destruction, active periostitis, soft tissue mass and tumour length. The MRI-features were compared with the histopathological tumour grading using univariate, multivariate logistic regression and receiver operating characteristic curve (ROC) analyses. One hundred and seventy-nine tumours were included in this retrospective study. There were 28 atypical cartilaginous tumours, 79 grade 1 chondrosarcomas, 36 grade 2 chondrosarcomas, 13 grade 3 chondrosarcomas and 23 dedifferentiated chondrosarcomas. Multivariate analysis demonstrated that bone expansion (P = 0.001), active periostitis (P = 0.001), soft tissue mass (P < 0.001) and tumour length (P < 0.001) were statistically significant differentiating factors between low-grade and high-grade chondral lesions with an area under the ROC curve of 0.956. On MRI, bone expansion, active periostitis, soft tissue mass and tumour length can reliably differentiate high-grade chondrosarcomas from low-grade chondral lesions of the major long bones. (orig.)

  2. Peer Victimization in Fifth Grade and Health in Tenth Grade

    Science.gov (United States)

    Elliott, Marc N.; Klein, David J.; Tortolero, Susan R.; Mrug, Sylvie; Peskin, Melissa F.; Davies, Susan L.; Schink, Elizabeth T.; Schuster, Mark A.

    2014-01-01

    BACKGROUND AND OBJECTIVES: Children who experience bullying, a type of peer victimization, show worse mental and physical health cross-sectionally. Few studies have assessed these relationships longitudinally. We examined longitudinal associations of bullying with mental and physical health from elementary to high school, comparing effects of different bullying histories. METHODS: We analyzed data from 4297 children surveyed at 3 time points (fifth, seventh, and tenth grades) in 3 cities. We used multivariable regressions to test longitudinal associations of bullying with mental and physical health by comparing youth who experienced bullying in both the past and present, experienced bullying in the present only, experienced bullying in the past only, or did not experience bullying. RESULTS: Bullying was associated with worse mental and physical health, greater depression symptoms, and lower self-worth over time. Health was significantly worse for children with both past and present bullying experiences, followed by children with present-only experiences, children with past-only experiences, and children with no experiences. For example, 44.6% of children bullied in both the past and present were at the lowest decile of psychosocial health, compared with 30.7% of those bullied in the present only (P = .005), 12.1% of those bullied in the past only (P bullied (P bullying are associated with substantially worse health. Clinicians who recognize bullying when it first starts could intervene to reverse the downward health trajectory experienced by youth who are repeated targets. PMID:24534401

  3. What's in a Grade? Grading Policies and Practices in Principles of Economics

    Science.gov (United States)

    Walstad, William B.; Miller, Laurie A.

    2016-01-01

    Survey results from a national sample of economics instructors describe the grading policies and practices in principles of economics courses. The survey results provide insights about absolute and relative grading systems used by instructors, the course components and their weights that determine grades, and the type of assessment items used for…

  4. [Reproducibility of Fuhrman nuclear grade: advantages of a two-grade system].

    Science.gov (United States)

    Letourneux, Hervé; Lindner, Véronique; Lang, Hervé; Massfelder, Thierry; Meyer, Nicolas; Saussine, Christian; Jacqmin, Didier

    2006-06-01

    The Fuhrman nuclear grade is the reference histoprognostic grading system routinely used all over the world for renal cell carcinoma. Studies measuring the inter-observer and intra-observer concordance of Fuhrman grade show poor results in terms of reproducibility and repeatability. These variations are due to a certain degree of subjectivity of the pathologist in application of the definition of tumour grade, particularly nuclear grade. Elements able to account for this subjectivity in renal cell carcinoma are identified from a review of the literature. To improve the reliability of nuclear grade, the territory occupied by the highest grade must be specified and the grades should probably be combined. At the present time, regrouping of grade 1 and 2 tumours as low grade and grade 3 and 4 tumours as high grade would achieve better reproducibility, while preserving the prognostic: value for overall survival. The development of new treatment modalities and their use in adjuvant situations will imply the use of reliable histoprognostic factors to specify, indications.

  5. Teachers grading practices : an analysis of the reliability of teacher-assigned grade point average (GPA)

    NARCIS (Netherlands)

    van der Lans, R. M.; van de Grift, W. J. C. M.; van Veen, K.

    2015-01-01

    In previous research, teachers report that they use a hodgepodge of factors when grading students. This has led researchers to suspect that teacher-assigned grades are inflated by teacher-student interactions; the hodgepodge hypothesis. Teachers also are reported to differ in grading leniency; the

  6. The Impact of Early Exposure of Eighth Grade Math Standards on End of Grade Assessments

    Science.gov (United States)

    Robertson, Tonjai E.

    2016-01-01

    The purpose of this study was to examine the Cumberland County Schools district-wide issue surrounding the disproportional performance of eighth grade Math I students' proficiency scores on standardized end-of-grade and end-of-course assessments. The study focused on the impact of the school district incorporating eighth grade math standards in…

  7. Are Flunkers Social Outcasts? A Multilevel Study of Grade Retention Effects on Same-Grade Friendships

    Science.gov (United States)

    Demanet, Jannick; Van Houtte, Mieke

    2016-01-01

    We examine the association between grade retention and the number of same-grade friendships. Moreover, we investigate the effect of a school's proportion of retained students on these friendships and the moderating effect of this school characteristic on the relationship between retention and the number of same-grade friendships. Multilevel…

  8. Fifth Grade Elementary Students' Conceptions of Earthquakes

    Science.gov (United States)

    Savasci, Funda; Uluduz, Hatice

    2013-01-01

    This study intends to investigate the fifth grade students' conceptions of earthquakes. Twenty two grade 5 students (11-12 years old) from five different elementary schools in Istanbul voluntarily participated in the study. Data were collected from semi-structured interviews with each participant. Six interview questions were designed by…

  9. Matriculation Research Report: Incomplete Grades; Data & Analysis.

    Science.gov (United States)

    Gerda, Joe

    The policy on incomplete grades at California's College of the Canyons states that incompletes may only be given under circumstances beyond students' control and that students must make arrangements with faculty prior to the end of the semester to clear the incomplete. Failure to complete an incomplete may result in an "F" grade. While…

  10. The Leap into 4th Grade

    Science.gov (United States)

    Anderson, Mike

    2011-01-01

    Fourth grade is a pivotal year, in which students commonly face increased academic demands. According to Anderson, teachers can help students make a smooth transition to 4th grade by introducing these new challenges in ways that are in line with 4th graders' common developmental characteristics: incredible energy and emotion, industriousness and…

  11. Bruxism defined and graded: an international consensus

    NARCIS (Netherlands)

    Lobbezoo, F.; Ahlberg, J.; Glaros, A.G.; Kato, T.; Koyano, K.; Lavigne, G.J.; de Leeuw, R.; Manfredini, D.; Svensson, P.; Winocur, E.

    2013-01-01

    To date, there is no consensus about the definition and diagnostic grading of bruxism. A written consensus discussion was held among an international group of bruxism experts as to formulate a definition of bruxism and to suggest a grading system for its operationalisation. The expert group defined

  12. Perceptions of restaurateurs on quality grading

    Directory of Open Access Journals (Sweden)

    Joseph Roberson

    2014-01-01

    Full Text Available A restaurateur's strategic focus is to maximise wealth for the owner(s. To achieve wealth maximisation, a restaurateur could implement one or more of the following strategies: focus strategy, cost-leadership strategy and/or differentiation strategy. A management intervention a restaurateur could implement to achieve this is quality differentiation. Grading of an establishment will assist a restaurateur in becoming a market leader. Currently there no national restaurant grading system exists in South Africa. As support and participation of restaurateurs in any future quality grading system are essential, it is imperative to test their perceptions of the implementation of a quality grading scale. The aim of this paper is to gather the perceptions of restaurateurs of an envisaged scale that could be used to grade independent full-service restaurants. In this study the researcher tested the perceptions of restaurateurs using nine possible outcomes of implementing quality grading in the independent fullservice restaurant segment. The outcomes to be tested were presented to restaurateurs in a questionnaire uploaded on "survey monkey". This was emailed to 3 286 restaurateurs and 265 responses were received. Respondents who were positive regarding grading indicated that they were enthusiastic about the impact grading would have on international tourism, as well as the fact that it could contribute to an increase in the value of their establishments.

  13. 7 CFR 51.2556 - Grades.

    Science.gov (United States)

    2010-01-01

    ... Standards for Grades of Shelled Pistachio Nuts § 51.2556 Grades. (a) “U.S. Fancy,” “U.S. Extra No. 1,” and “U.S. No. 1” consist of pistachio kernels which meet the following requirements: (1) Well dried, or...

  14. Contraction of graded su(2) algebra

    International Nuclear Information System (INIS)

    Patra, M.K.; Tripathy, K.C.

    1989-01-01

    The Inoenu-Wigner contraction scheme is extended to Lie superalgebras. The structure and representations of extended BRS algebra are obtained from contraction of the graded su(2) algebra. From cohomological consideration, we demonstrate that the graded su(2) algebra is the only superalgebra which, on contraction, yields the full BRS algebra. (orig.)

  15. What's ahead in automated lumber grading

    Science.gov (United States)

    D. Earl Kline; Richard Conners; Philip A. Araman

    1998-01-01

    This paper discusses how present scanning technologies are being applied to automatic lumber grading. The presentation focuses on 1) what sensing and scanning devices are needed to measure information for accurate grading feature detection, 2) the hardware and software needed to efficiently process this information, and 3) specific issues related to softwood lumber...

  16. Liberal Grading Improves Evaluations But Not Performance.

    Science.gov (United States)

    Vasta, Ross; Sarmiento, Robert F.

    Two grading distributions--a liberal and a more stringent curve--were compared between two sections of an undergraduate psychology course. The two classes were team taught and treated as similarly as possible. Four unit exams and an optional final were administered, with one section consistently receiving a more lenient grade distribution. No…

  17. Examining First Grade Teachers' Handwriting Instruction

    Science.gov (United States)

    Arslan, Derya

    2012-01-01

    The purpose of this study is to examine the first grade teachers' practices of handwriting instructions in terms of teaching, evaluation and handwriting difficulties. From qualitative research patterns, phenomenology was used. The study was applied to the 54 First grade teachers who work at central Burdur and Burdur county centre primary education…

  18. Extrauterine Low-Grade Endometrial Stromal Sarcoma

    Directory of Open Access Journals (Sweden)

    Yu-Ju Chen

    2005-12-01

    Conclusions: Low-grade endometrial stromal sarcoma typically has an indolent clinical course and favorable prognosis. Surgical resection is the primary therapeutic approach, and adjuvant therapy with radiotherapy, chemotherapy, or progesterone therapy should be considered for the management of residual or recurrent low-grade endometrial stromal sarcomas.

  19. Grade Repetition in Queensland State Prep Classes

    Science.gov (United States)

    Anderson, Robyn

    2012-01-01

    The current study considers grade repetition rates in the early years of schooling in Queensland state schools with specific focus on the pre-schooling year, Prep. In particular, it provides empirical evidence of grade repetition in Queensland state schools along with groups of students who are more often repeated. At the same time, much of the…

  20. Consumer Preference for Graded Maple Syrup

    Science.gov (United States)

    Paul E. Sendak

    1978-01-01

    The three grades of maple syrup and a commercial table syrup containing artificial flavor and 3 percent pure maple syrup were evaluated by 1,018 women in four cities. The results indicate that differences in preference for flavor are related to how close the respondents are to a maple syrup-production region. Differences in preference among grades of pure maple syrup...

  1. Determinants of College Grade Point Averages

    Science.gov (United States)

    Bailey, Paul Dean

    2012-01-01

    Chapter 2: The Role of Class Difficulty in College Grade Point Averages. Grade Point Averages (GPAs) are widely used as a measure of college students' ability. Low GPAs can remove a students from eligibility for scholarships, and even continued enrollment at a university. However, GPAs are determined not only by student ability but also by the…

  2. Grading sugar pine saw logs in trees.

    Science.gov (United States)

    John W. Henley

    1972-01-01

    Small limbs and small overgrown limbs cause problems when grading saw logs in sugar pine trees. Surface characteristics and lumber recovery information for 426 logs from 64 sugar pine trees were examined. Resulting modifications in the grading specification that allow a grader to ignore small limbs and small limb indicators do not appear to decrease the performance of...

  3. Improvement in grade of minerals using simultaneous Bio-oxidation of invisible gold concentrate and deep-sea manganese crust

    Science.gov (United States)

    Myung, EunJi; Cho, Kang Hee; Kim, Hyun Soo; Park, Cheon Young

    2016-04-01

    Many sulfides of metal such as galena, sphalerite, chalcopyrite, and pyrite, are semiconductors. When two kinds of such minerals contact each other in an electrolyte, a galvanic couple, where the mineral of lower rest potential as anode, and that of higher rest potential as cathode forms. Manganese dioxide is also a semiconductor with much higher rest potential than all sulfides mentioned above, so that a galvanic couple in which both the minerals would dissolve simultaneously can form, when it contacts with any of the sulfides. The aim of this study was to investigate the improvement in grade of minerals using the simultaneous bio-oxidation of deep-sea manganese crust and invisible gold concentrate. The samples(deep-sea manganese crust and invisible gold concentrate) were characterized by chemical and XRD analysis. The primary components of the invisible gold concentrate was pyrite and quartz and the deep-sea manganese crust was amorphous material, as detected using XRD. The result of chemical analysis showed that Au, Ag, Te contents in the invisible gold concentrate 130.2, 954.1 and 1,043.6 mg/kg, respectively. and that Mn, Ni, Co contents in the deep-sea manganese crust 19,501.5, 151.9, 400.4 mg/kg, respectively. In order to increase the bacteria's tolerance of heavy metals, the bacteria using bio-oxidation experiments were repeatedly subcultured in an Cu adaptation-medium containing of 382.98 mg/l for 20 periods of 21 days. The improvement in grade of samples of in present adapted bacteria condition was greater than another conditions(control and in present non-adapted bacteria). The Au-Ag-Te contents in the invisible gold concentrate was enhanced in the order of physical oxidation, simultaneous/non-adaptive bio-oxidation, adaptive/bio-oxidation, simultaneous/adaptive bio-oxidation. If the bacteria is adapted to heavy metal ions and an optimization of conditions is found in future bio-oxidation-leaching processes. Acknowledgment : "This research was supported

  4. Graded activity: legacy of the sanatorium.

    Science.gov (United States)

    Creighton, C

    1993-08-01

    Occupational therapists in all areas of practice grade therapeutic activities to help patients progress toward their goals. It is proposed in this paper that the concept of graded activity originated in German tuberculosis sanatoria in the late 1800s, when patients were required to walk on graded (sloped) land for exercise. British physician Marcus Paterson included work, as well as walking, in his graduated exercise program for tuberculosis patients and was honored for this innovation at the founding meeting of the National Society for the Promotion of Occupational Therapy (NSPOT). George Barton, Susan Tracy, and Herbert Hall were among the NSPOT members who contributed to the development of graded activity as a principle in occupational therapy intervention. The military rehabilitation programs established during World War I provided additional impetus, and by the mid-1920s, graded activity was recognized as central to the profession.

  5. Functionally Graded Adhesives for Composite Joints

    Science.gov (United States)

    Stapleton, Scott E.; Waas, Anthony M.; Arnold, Steven M.

    2012-01-01

    Adhesives with functionally graded material properties are being considered for use in adhesively bonded joints to reduce the peel stress concentrations located near adherend discontinuities. Several practical concerns impede the actual use of such adhesives. These include increased manufacturing complications, alterations to the grading due to adhesive flow during manufacturing, and whether changing the loading conditions significantly impact the effectiveness of the grading. An analytical study is conducted to address these three concerns. An enhanced joint finite element, which uses an analytical formulation to obtain exact shape functions, is used to model the joint. Furthermore, proof of concept testing is conducted to show the potential advantages of functionally graded adhesives. In this study, grading is achieved by strategically placing glass beads within the adhesive layer at different densities along the joint.

  6. Foraminal syringomyelia: suggestion for a grading system.

    Science.gov (United States)

    Versari, P P; D'Aliberti, G; Talamonti, G; Collice, M

    1993-01-01

    The standard treatment of foraminal syringomyelia includes foramen magnum decompression and duraplasty. Improvement or stabilization of the disease are achieved in most of cases. However, at least one third of patients are reported to receive little or no benefit. In this paper we retrospectively reviewed a series of 40 consecutive foramen magnum decompressions in order to identify the possible pre-operative outcome predictors. Based on clinical evolution, neurological impairment and radiological features, a scale of severity was fixed and retrospectively tested. A pre-operative score was obtained for each patient and was correlated with the surgical results. Then a four level grading system was derived. All grade I and grade II patients achieved good results (improvement or stabilization), whereas grade III patients showed intermediate behaviour and grade IV invariably worsened. On this basis, surgical results of foramen magnum decompression might be further improved provided that a careful pre-operative selection is made.

  7. Automated tone grading of granite

    International Nuclear Information System (INIS)

    Catalina Hernández, J.C.; Fernández Ramón, G.

    2017-01-01

    The production of a natural stone processing plant is subject to the intrinsic variability of the stone blocks that constitute its raw material, which may cause problems of lack of uniformity in the visual appearance of the produced material that often triggers complaints from customers. The best way to tackle this problem is to classify the product according to its visual features, which is traditionally done by hand: an operator observes each and every piece that comes out of the production line and assigns it to the closest match among a number of predefined classes, taking into account visual features of the material such as colour, texture, grain, veins, etc. However, this manual procedure presents significant consistency problems, due to the inherent subjectivity of the classification performed by each operator, and the errors caused by their progressive fatigue. Attempts to employ automated sorting systems like the ones used in the ceramic tile industry have not been successful, as natural stone presents much higher variability than ceramic tiles. Therefore, it has been necessary to develop classification systems specifically designed for the treatment of the visual parameters that distinguish the different types of natural stone. This paper describes the details of a computer vision system developed by AITEMIN for the automatic classification of granite pieces according to their tone, which provides an integral solution to tone grading problems in the granite processing and marketing industry. The system has been designed to be easily trained by the end user, through the learning of the samples established as tone patterns by the user. [es

  8. GRADE INFLATION: An Issue for Higher Education?

    Directory of Open Access Journals (Sweden)

    Donald L. CARUTH,

    2013-01-01

    Full Text Available Grade inflation impacts university credibility, student courses of study, choices of institution, and other areas. There has been an upward shift in grades without a corresponding upward shift in knowledge gained. Some of the most frequently mentioned causes of grade inflation are: Ø student evaluations of professors, Ø student teacher dynamics, Ø merit-based financial aid, and Ø student expectations. Ø Among the reasons for higher student grades on the part of professors are: Ø fear of student evaluations, Ø avoidance of bad relations with students, Ø below average teaching skills,Ø lack of experience, Ø a lack of clearly stated objectives, and Ø job security. While grades are not a perfect answer to assessing student performance in a course they are still the best answer we have for evaluating students. In order to evaluate students more accurately, universities must identify the problems in grading and grading practices. Once this is accomplished new practices can be designed and policies implemented.

  9. Power calculation of grading device in desintegrator

    Science.gov (United States)

    Bogdanov, V. S.; Semikopenko, I. A.; Vavilov, D. V.

    2018-03-01

    This article describes the analytical method of measuring the secondary power consumption, necessitated by the installation of a grading device in the peripheral part of the grinding chamber in the desintegrator. There is a calculation model for defining the power input of the disintegrator increased by the extra power demand, required to rotate the grading device and to grind the material in the area between the external row of hammers and the grading device. The work has determined the inertia moments of a cylindrical section of the grading device with armour plates. The processing capacity of the grading device is adjusted to the conveying capacity of the auger feeder. The grading device enables one to increase the concentration of particles in the peripheral part of the grinding chamber and the amount of interaction between particles and armour plates as well as the number of colliding particles. The perforated sections provide the output of the ground material with the proper size granules, which together with the effects of armour plates, improves the efficiency of grinding. The power demand to rotate the grading device does not exceed the admissible value.

  10. Alternative Grading Systems. The Practitioner, Vol. III, No. 3.

    Science.gov (United States)

    De Leonibus, Nancy; Thomson, Scott

    After examining some of the pros and cons of traditional grading, the demands colleges make on grading practices, and the responses of people interested in grading, a number of examples of operating alternative systems are given. The alternatives include a dual (pass/withdraw grading in some courses, traditional grading in others) system, a…

  11. 7 CFR 51.1578 - Off-Grade potatoes.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Off-Grade potatoes. 51.1578 Section 51.1578... STANDARDS) United States Consumer Standards for Potatoes Off-Grade § 51.1578 Off-Grade potatoes. Potatoes which fail to meet the requirements of any of the foregoing grades shall be Off-Grade potatoes...

  12. Asymmetric acoustic transmission in graded beam

    Energy Technology Data Exchange (ETDEWEB)

    Jing, Li, E-mail: lj94172350@hotmail.com [School of Mechanical Engineering and State Key laboratory for Strength and Vibration of Mechanical Structures, Xi’an Jiaotong University, Xi’an, Shaanxi 710049 (China); Wu, Jiu Hui, E-mail: ejhwu@mail.xjtu.edu.cn [School of Mechanical Engineering and State Key laboratory for Strength and Vibration of Mechanical Structures, Xi’an Jiaotong University, Xi’an, Shaanxi 710049 (China); Guan, Dong; Lu, Kuan [School of Mechanical Engineering and State Key laboratory for Strength and Vibration of Mechanical Structures, Xi’an Jiaotong University, Xi’an, Shaanxi 710049 (China); Gao, Nansha [School of Marine Science and Technology, Northwestern Polytechnical University, Xi’an, Shaanxi 710072 (China); Songhua, Cao [School of Mechanical Engineering and State Key laboratory for Strength and Vibration of Mechanical Structures, Xi’an Jiaotong University, Xi’an, Shaanxi 710049 (China)

    2016-12-01

    We demonstrate the dynamic effective material parameters and vibration performance of a graded beam. The structure of the beam was composed of several unit cells with different fill factors. The dispersion relations and energy band structures of each unit cell were calculated using the finite element method (FEM). The dynamic effective material parameters in each unit cell of the graded beam were determined by the dispersion relations and energy band structures. Longitudinal wave propagation was investigated using a numerical method and FEM. The results show that the graded beam allows asymmetric acoustic transmission over a wide range of frequencies.

  13. Graded Alternating-Time Temporal Logic

    Science.gov (United States)

    Faella, Marco; Napoli, Margherita; Parente, Mimmo

    Graded modalities enrich the universal and existential quantifiers with the capability to express the concept of at least k or all but k, for a non-negative integer k. Recently, temporal logics such as μ-calculus and Computational Tree Logic, Ctl, augmented with graded modalities have received attention from the scientific community, both from a theoretical side and from an applicative perspective. Both μ-calculus and Ctl naturally apply as specification languages for closed systems: in this paper, we add graded modalities to the Alternating-time Temporal Logic (Atl) introduced by Alur et al., to study how these modalities may affect specification languages for open systems.

  14. ENERGY STAR Laboratory Grade Refrigerators and Freezers

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.0 ENERGY STAR Program Requirements for Laboratory Grade Refrigerators and Freezers that...

  15. High Performance Graded Index Polymer Optical Fibers

    National Research Council Canada - National Science Library

    Garito, Anthony

    1998-01-01

    ...) plastic optical fibers (POF) and graded index (GI) POFs are reported. A set of criteria and analyses of physical parameters are developed in context to the major issues of POF applications in short-distance communication systems...

  16. Bruxism defined and graded: an international consensus.

    Science.gov (United States)

    Lobbezoo, F; Ahlberg, J; Glaros, A G; Kato, T; Koyano, K; Lavigne, G J; de Leeuw, R; Manfredini, D; Svensson, P; Winocur, E

    2013-01-01

    To date, there is no consensus about the definition and diagnostic grading of bruxism. A written consensus discussion was held among an international group of bruxism experts as to formulate a definition of bruxism and to suggest a grading system for its operationalisation. The expert group defined bruxism as a repetitive jaw-muscle activity characterised by clenching or grinding of the teeth and/or by bracing or thrusting of the mandible. Bruxism has two distinct circadian manifestations: it can occur during sleep (indicated as sleep bruxism) or during wakefulness (indicated as awake bruxism). For the operationalisation of this definition, the expert group proposes a diagnostic grading system of 'possible', 'probable' and 'definite' sleep or awake bruxism. The proposed definition and grading system are suggested for clinical and research purposes in all relevant dental and medical domains. © 2012 Blackwell Publishing Ltd.

  17. Kindergarten Predictors of Third Grade Writing

    Science.gov (United States)

    Kim, Young-Suk; Al Otaiba, Stephanie; Wanzek, Jeanne

    2015-01-01

    The primary goal of the present study was to examine the relations of kindergarten transcription, oral language, word reading, and attention skills to writing skills in third grade. Children (N = 157) were assessed on their letter writing automaticity, spelling, oral language, word reading, and attention in kindergarten. Then, they were assessed on writing in third grade using three writing tasks – one narrative and two expository prompts. Children’s written compositions were evaluated in terms of writing quality (the extent to which ideas were developed and presented in an organized manner). Structural equation modeling showed that kindergarten oral language and lexical literacy skills (i.e., word reading and spelling) were independently predicted third grade narrative writing quality, and kindergarten literacy skill uniquely predicted third grade expository writing quality. In contrast, attention and letter writing automaticity were not directly related to writing quality in either narrative or expository genre. These results are discussed in light of theoretical and practical implications. PMID:25642118

  18. Statistical Content in Middle Grades Mathematics Textbooks

    Science.gov (United States)

    Pickle, Maria Consuelo Capiral

    2012-01-01

    This study analyzed the treatment and scope of statistical concepts in four, widely-used, contemporary, middle grades mathematics textbook series: "Glencoe Math Connects," "Prentice Hall Mathematics," "Connected Mathematics Project," and "University of Chicago School Mathematics Project." There were three…

  19. Doubly graded sigma model with torsion

    International Nuclear Information System (INIS)

    Kowalski-Glikman, J.

    1986-08-01

    Using the Hull-Witten construction we show how to introduce torsion to the doubly graded sigma model. This construction enables us to find a link between this model and the ten-dimensional supergravity theory in superspace. (Auth.)

  20. Graded contractions of Jordan algebras and of their representations

    International Nuclear Information System (INIS)

    Kashuba, Iryna; Patera, JirI

    2003-01-01

    Contractions of Jordan algebras and Jordan superalgebras which preserve a chosen grading are defined and studied. Simultaneous grading of Jordan algebras and their representation spaces is used to develop a theory of grading, preserving contractions of representations of Jordan algebras

  1. Pollination biology of basal angiosperms (ANITA Grade)

    Science.gov (United States)

    Leonard B. Thien; Peter Bernhardt; Margaret S. Devall; Zhi-Duan Chen; Yi-bo Luo; Jian-Hua Fan; Liang-Chen Yuan; Joseph H. Williams

    2009-01-01

    The fi rst three branches of the angiosperm phylogenetic tree consist of eight families with ~201 species of plants (the ANITA grade). The oldest fl ower fossil for the group is dated to the Early Cretaceous (115 – 125 Mya) and identifi ed to the Nymphaeales. The fl owers of extant plants in the ANITA grade are small, and pollen is the edible reward (rarely nectar or...

  2. Meat standards and grading: a world view.

    Science.gov (United States)

    Polkinghorne, R J; Thompson, J M

    2010-09-01

    This paper addresses the principles relating to meat standards and grading of beef and advances the concept that potential exists to achieve significant desirable change from adopting more consumer focused systems within accurate value-based payment frameworks. The paper uses the definitions that classification is a set of descriptive terms describing features of the carcass that are useful to those involved in the trading of carcasses, whereas grading is the placing of different values on carcasses for pricing purposes, depending on the market and requirements of traders. A third definition is consumer grading, which refers to grading systems that seek to define or predict consumer satisfaction with a cooked meal. The development of carcass classification and grading schemes evolved from a necessity to describe the carcass using standard terms to facilitate trading. The growth in world trade of meat and meat products and the transition from trading carcasses to marketing individual meal portions raises the need for an international language that can service contemporary needs. This has in part been addressed by the United Nations promoting standard languages on carcasses, cuts, trim levels and cutting lines. Currently no standards exist for describing consumer satisfaction. Recent Meat Standards Australia (MSA) research in Australia, Korea, Ireland, USA, Japan and South Africa showed that consumers across diverse cultures and nationalities have a remarkably similar view of beef eating quality, which could be used to underpin an international language on palatability. Consumer research on the willingness to pay for eating quality shows that consumers will pay higher prices for better eating quality grades and generally this was not affected by demographic or meat preference traits of the consumer. In Australia the MSA eating quality grading system has generated substantial premiums to retailers, wholesalers and to the producer. Future grading schemes which measure

  3. Fatigue Characterization of Functionally Graded Metallic Alloys

    International Nuclear Information System (INIS)

    Silva, F. S.

    2008-01-01

    Functionally graded components exhibit spatial variations of mechanical properties in contrast with, and as an alternative to, purely homogeneous components. A large class of graded materials, however, are in fact mostly homogeneous materials with property variations (chemical or mechanical) restricted to a specific area or layer produced by applying for example a coating or by introducing sub-surface residual stresses. However, it is also possible to obtain graded materials with a smooth transition of mechanical properties along the entire component, for example in a 40 mm component. This is possible, for example, by using centrifugal casting technique or incremental melting and solidification technique. In this paper we will study fully metallic functionally graded components with a smooth gradient, focusing on fatigue crack propagation. Fatigue propagation will be assessed in the direction parallel to the gradation (in different homogeneous layers of the functionally graded component) to assess what would be fatigue crack propagation on the direction perpendicular to the gradation. Fatigue crack growth rate (standard mode I fatigue crack growth) will be correlated to the mode I stress intensity factor range. Other mechanical properties of different layers of the component (Young's modulus) will also be considered in this analysis. The effect of residual stresses along the component gradation on crack propagation will also be taken into account. A qualitative analysis of the effects of some important features, present in functionally graded materials, will be made based on the obtained results

  4. Age-Related Grade Inflation Expectancies in a University Environment

    Directory of Open Access Journals (Sweden)

    Donald A. Loffredo

    2012-01-01

    Full Text Available Grade inflation is a recognized problem in higher education in the United States. Age, gender, and ethnic differences in discrepancies between student reports of their expected grade in each course and their expectations for general university grading practices were explored in a survey of 166 (mostly female participants at a small upper-division university. Results revealed that while a small minority of students agreed that grading systems in college should only include A or B grades, a large majority of students expected A or B grades. Thus, student discrepancies between their expectations for grading systems and their expected class grades were in line with expectations that they should receive inflated grades. Results also revealed statistically significant age differences in grade expectation with students older than the age of 55 expecting lower grades relative to their younger counterparts.

  5. Burning weapons-grade plutonium in reactors

    International Nuclear Information System (INIS)

    Newman, D.F.

    1993-06-01

    As a result of massive reductions in deployed nuclear warheads, and their subsequent dismantlement, large quantities of surplus weapons- grade plutonium will be stored until its ultimate disposition is achieved in both the US and Russia. Ultimate disposition has the following minimum requirements: (1) preclude return of plutonium to the US and Russian stockpiles, (2) prevent environmental damage by precluding release of plutonium contamination, and (3) prevent proliferation by precluding plutonium diversion to sub-national groups or nonweapons states. The most efficient and effective way to dispose of surplus weapons-grade plutonium is to fabricate it into fuel and use it for generation of electrical energy in commercial nuclear power plants. Weapons-grade plutonium can be used as fuel in existing commercial nuclear power plants, such as those in the US and Russia. This recovers energy and economic value from weapons-grade plutonium, which otherwise represents a large cost liability to maintain in safeguarded and secure storage. The plutonium remaining in spent MOX fuel is reactor-grade, essentially the same as that being discharged in spent UO 2 fuels. MOX fuels are well developed and are currently used in a number of LWRs in Europe. Plutonium-bearing fuels without uranium (non-fertile fuels) would require some development. However, such non-fertile fuels are attractive from a nonproliferation perspective because they avoid the insitu production of additional plutonium and enhance the annihilation of the plutonium inventory on a once-through fuel cycle

  6. Multiparametric Magnetic Resonance Imaging for Discriminating Low-Grade From High-Grade Prostate Cancer

    NARCIS (Netherlands)

    Vos, E.K.; Kobus, T.; Litjens, G.J.S.; Hambrock, T.; Hulsbergen-van de Kaa, C.A.; Barentsz, J.O.; Maas, M.C.; Scheenen, T.W.J.

    2015-01-01

    The aim of this study was to determine and validate the optimal combination of parameters derived from 3-T diffusion-weighted imaging, dynamic contrast-enhanced imaging, and magnetic resonance (MR) spectroscopic imaging for discriminating low-grade from high-grade prostate cancer (PCa).The study was

  7. 7 CFR 810.804 - Grades and grade requirements for mixed grain.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Grades and grade requirements for mixed grain. 810.804 Section 810.804 Agriculture Regulations of the Department of Agriculture (Continued) GRAIN INSPECTION, PACKERS AND STOCKYARD ADMINISTRATION (FEDERAL GRAIN INSPECTION SERVICE), DEPARTMENT OF AGRICULTURE...

  8. Does Grade Inflation Affect the Credibility of Grades? Evidence from US Law School Admissions

    Science.gov (United States)

    Wongsurawat, Winai

    2009-01-01

    While the nature and causes of university grade inflation have been extensively studied, little empirical research on the consequence of this phenomenon is currently available. The present study uses data for 48 US law schools to analyze admission decisions in 1995, 2000, and 2007, a period during which university grade inflation appears to have…

  9. Colorado Student Assessment Program: 2001 Released Passages, Items, and Prompts. Grade 4 Reading and Writing, Grade 4 Lectura y Escritura, Grade 5 Mathematics and Reading, Grade 6 Reading, Grade 7 Reading and Writing, Grade 8 Mathematics, Reading and Science, Grade 9 Reading, and Grade 10 Mathematics and Reading and Writing.

    Science.gov (United States)

    Colorado State Dept. of Education, Denver.

    This document contains released reading comprehension passages, test items, and writing prompts from the Colorado Student Assessment Program for 2001. The sample questions and prompts are included without answers or examples of student responses. Test materials are included for: (1) Grade 4 Reading and Writing; (2) Grade 4 Lectura y Escritura…

  10. Grades and Incentives: Assessing Competing Grade Point Average Measures and Postgraduate Outcomes

    Science.gov (United States)

    Bailey, Michael A.; Rosenthal, Jeffrey S.; Yoon, Albert H.

    2016-01-01

    In many educational settings, students may have an incentive to take courses where high grades are easier to achieve, potentially corroding student learning, evaluation of student achievement, and the fairness and efficiency of post-graduation labor outcomes. A grading system that takes into account heterogeneity of teacher standards and student…

  11. Comparing 2 Whiplash Grading Systems to Predict Clinical Outcomes.

    Science.gov (United States)

    Croft, Arthur C; Bagherian, Alireza; Mickelsen, Patrick K; Wagner, Stephen

    2016-06-01

    Two whiplash severity grading systems have been developed: Quebec Task Force on Whiplash-Associated Disorders (QTF-WAD) and the Croft grading system. The majority of clinical studies to date have used the modified grading system published by the QTF-WAD in 1995 and have demonstrated some ability to predict outcome. But most studies include only injuries of lower severity (grades 1 and 2), preventing a broader interpretation. The purpose of this study was assess the ability of these grading systems to predict clinical outcome within the context of a broader injury spectrum. This study evaluated both grading systems for their ability to predict the bivalent outcome, recovery, within a sample of 118 whiplash patients who were part of a previous case-control designed study. Of these, 36% (controls) had recovered, and 64% (cases) had not recovered. The discrete bivariate distribution between recovery status and whiplash grade was analyzed using the 2-tailed cross-tabulation statistics. Applying the criteria of the original 1993 Croft grading system, the subset comprised 1 grade 1 injury, 32 grade 2 injuries, 53 grade 3 injuries, and 32 grade 4 injuries. Applying the criteria of the modified (QTF-WAD) grading system, there were 1 grade 1 injury, 89 grade 2 injuries, and 28 grade 3 injuries. Both whiplash grading systems correlated negatively with recovery; that is, higher severity grades predicted a lower probability of recovery, and statistically significant correlations were observed in both, but the Croft grading system substantially outperformed the QTF-WAD system on this measure. The Croft grading system for whiplash injury severity showed a better predictive measure for recovery status from whiplash injuries as compared with the QTF-WAD grading system.

  12. Grading as a Sadomasochistic Activity or an Erotic Benevolent Activity?

    Science.gov (United States)

    Tjarks, Larry D.

    Numerous research studies have been conducted concerning the negative aspects of grading: the low correlations between academic success (high grades) and later vocational or professional success, possible sadomasochistic motives of teachers in awarding grades, and grade assignment resulting from the teacher's sense of duty or responsibility to…

  13. A Machine Vision System for Automatically Grading Hardwood Lumber - (Proceedings)

    Science.gov (United States)

    Richard W. Conners; Tai-Hoon Cho; Chong T. Ng; Thomas H. Drayer; Joe G. Tront; Philip A. Araman; Robert L. Brisbon

    1990-01-01

    Any automatic system for grading hardwood lumber can conceptually be divided into two components. One of these is a machine vision system for locating and identifying grading defects. The other is an automatic grading program that accepts as input the output of the machine vision system and, based on these data, determines the grade of a board. The progress that has...

  14. Effects of Instructions on Theme Grading: Grammatical vs. Holistic

    Science.gov (United States)

    Follman, John; And Others

    1971-01-01

    Twelve college seniors in an English methods course were assigned to three treatment groups, Grammatical, Holistic, and Both. Each group received different instructions but graded the same 10 themes. Themes graded for grammatical errors received lower grades than the same themes graded holistically. (NH)

  15. What Is Wrong with Grade Inflation (If Anything)?

    Science.gov (United States)

    Finefter-Rosenbluh, Ilana; Levinson, Meira

    2015-01-01

    Grade inflation is a global phenomenon that has garnered widespread condemnation among educators, researchers, and the public. Yet, few have deliberated over the ethics of grading, let alone the ethics of grade inflation. The purpose of this paper is to map out and examine the ethics of grade inflation. By way of beginning, we clarify why grade…

  16. 7 CFR 70.105 - Procedures for appeal gradings.

    Science.gov (United States)

    2010-01-01

    ... conducting the appeal grading. Whether defrosting poultry or rabbit carcasses for other types of appeals will... 7 Agriculture 3 2010-01-01 2010-01-01 false Procedures for appeal gradings. 70.105 Section 70.105... PRODUCTS AND RABBIT PRODUCTS Grading of Poultry Products and Rabbit Products Appeal of A Grading Or...

  17. Advantages and Disadvantages of Weighted Grading. Research Brief

    Science.gov (United States)

    Walker, Karen

    2004-01-01

    What are the advantages and disadvantages of weighted grading? The primary purpose of weighted grading has been to encourage high school students to take more rigorous courses. This effort is then acknowledged by more weight being given to the grade for a specified class. There are numerous systems of weighted grading cited in the literature from…

  18. 77 FR 6772 - United States Standards for Grades of Cauliflower

    Science.gov (United States)

    2012-02-09

    ... Service [Doc. AMS-FV-10-0047] United States Standards for Grades of Cauliflower AGENCY: Agricultural... Standards for Grades of Cauliflower. AMS is reviewing all fresh fruit and vegetable grade standards for... provisions for grading purple, orange or green cauliflower. The proposed revision will amend the color...

  19. Properties of textile grade ceramic fibers

    International Nuclear Information System (INIS)

    Pudnos, E.

    1992-01-01

    The availability of textile grade ceramic fibers has sparked great interest for applications in composite reinforcement and high temperature insulation. This paper summarizes the properties of various small diameter textile grade ceramic fibers currently available. Room temperature mechanical and electrical properties of the fibers are discussed for three cases: ambient conditions, after heat aging in argon, and after heat aging in wet air. Dow Corning (R) HPZ Ceramic Fiber, a silicon nitride type fiber, is shown to have improved retention of mechanical and electrical properties above 1200 C

  20. Graded thermal insulation layer systems; Gradierte Waermedaemmschichtsysteme

    Energy Technology Data Exchange (ETDEWEB)

    Leushake, U.; Krell, T. [Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Koeln (Germany). Inst. fuer Werkstoff-Forschung

    1996-12-31

    Graded thermal insulation systems reduce local stresses between two layers. Grading usually involves a concentration variation in a second phase but may also involve variations of the microstructure or chemical composition. The contribution discusses the application of this technique for thermal protection of turbine blades in aircraft propulsion systems. [Deutsch] Mit Hilfe gradierter Waermeschichtsysteme ist es moeglich die lokalen Spannungen zwischen zwei Schichten zu verringern. Die Gradierung umfasst meistens eine Variation des Gehaltes einer zweiten Phase, kann aber auch die Variation der Mikrostruktur oder der chemischen Zusammensetzung beinhalten. In diesem Beitrag wird auf die Anwendung als thermischer Schutz von Turbinenschaufeln fuer Flugtriebwerke eingegangen.

  1. Studies on high grade cerebral gliomas

    International Nuclear Information System (INIS)

    Bleehen, N.M.

    1990-01-01

    A brief review of attempts in the United Kingdom to improve the results of treatment of high grade (grade 3, 4) supra-tentorial astrocytomas is presented. The radiosensitizer misonidazole failed to improve the results of post-surgical radiotherapy, however, multivariate analysis of data from these patients has provided a prognostic index of use in defining good and poor prognosis patients. An overview study of adjuvant nitrosourea therapy trials has shown a small significant advantage for the chemotherapy. A study of chemosensitization by benznidazole of CCNU treatment of patients in relapse failed to demonstrate any effect. 13 references

  2. Graded photonic crystals by optical interference holography

    International Nuclear Information System (INIS)

    Han, Chunrui; Tam, Wing Yim

    2012-01-01

    We report on the fabrication of graded photonic crystals in dye doped dichromate gelatin emulsions using an optical interference holographic technique. The gradedness is achieved by imposing a gradient form factor in the interference intensity resulting from the absorption of the dye in the dichromate gelatin. Wider and deeper photonic bandgaps are observed for the dyed samples as compared to the un-dyed samples. Our method could open up a new direction in fabricating graded photonic crystals which cannot be achieved easily using other techniques. (paper)

  3. Graded associative conformal algebras of finite type

    OpenAIRE

    Kolesnikov, Pavel

    2011-01-01

    In this paper, we consider graded associative conformal algebras. The class of these objects includes pseudo-algebras over non-cocommutative Hopf algebras of regular functions on some linear algebraic groups. In particular, an associative conformal algebra which is graded by a finite group $\\Gamma $ is a pseudo-algebra over the coordinate Hopf algebra of a linear algebraic group $G$ such that the identity component $G^0$ is the affine line and $G/G^0\\simeq \\Gamma $. A classification of simple...

  4. Fibrocartilaginous mesenchymoma with low-grade malignancy

    International Nuclear Information System (INIS)

    Dahlin, D.C.; Bertoni, F.; Beabout, J.W.; Campanacci, M.

    1984-01-01

    In a review of cases of fibrous cartilaginous dysplasia of bone, five of fibrocartilaginous lesions were found to be different in clinical behavior and radiographic and morphologic features from the others. We have named these previously undescribed tumors ''fibrocartilaginous mesenchymomas with low-grade malignancy in the fibrous elements.'' (orig.)

  5. Do Class Size Effects Differ across Grades?

    Science.gov (United States)

    Nandrup, Anne Brink

    2016-01-01

    This paper contributes to the class size literature by analysing whether short-run class size effects are constant across grade levels in compulsory school. Results are based on administrative data on all pupils enrolled in Danish public schools. Identification is based on a government-imposed class size cap that creates exogenous variation in…

  6. Compressive properties of sandwiches with functionally graded

    Indian Academy of Sciences (India)

    The compressive behaviour of a new class of sandwich composite made up of jute fiber reinforced epoxy skins and piece-wise linear fly ash reinforced functionally graded (FG) rubber core is investigated in flat-wise mode. FG samples are prepared using conventional casting technique. Presence of gradation is quantified ...

  7. Does Social Background Influence Political Science Grades?

    Science.gov (United States)

    Tiruneh, Gizachew

    2013-01-01

    This paper tests a hypothesized linear relationship between social background and final grades in several political science courses that I taught at the University of Central Arkansas. I employ a cross-sectional research design and ordinary least square (OLS) estimators to test the foregoing hypothesis. Relying on a sample of up to 204…

  8. Teacher Grading Decisions: Influences, Rationale, and Practices

    Science.gov (United States)

    Kunnath, Joshua P.

    2017-01-01

    This mixed-methods study applied a decision-making theoretical framework to an investigation of teacher grading in a large urban school district in California. A sample of 251 high school teachers of core subjects were surveyed, and 15 teachers participated in four focus group interviews in order provide data on the influences, rationale, and…

  9. Mechanical Drawing: Grades 7-12.

    Science.gov (United States)

    Instructional Objectives Exchange, Los Angeles, CA.

    Eighty-five behavioral objectives and related evaluation items for mechanical drawing in grades 7 through 12 are presented. Each sample contains the objective, test items, and means for judging the adequacy of the response. The following categories are included: (1) basic drafting skills; (2) beginning lettering; (3) drawing; (4) orthographic…

  10. High grade magnesium from waste bittern

    International Nuclear Information System (INIS)

    El-Yamani, I.S.; Farah, M.Y.; Isaac, S.L.

    1979-01-01

    The production of high grade magnesia for nuclear purposes from sea water by use of both aqueous and gaseous ammonia has been described. The effect of precipitating conditions on the settling rate and magnesium recovery, was thoroughly examined. Ammonia gas approach was recommended and justified

  11. Lumber stress grades and design properties

    Science.gov (United States)

    David E. Kretschmann; David W. Green

    1999-01-01

    Lumber sawn from a log, regardless of species and size, is quite variable in mechanical properties. Pieces may differ in strength by several hundred percent. For simplicity and economy in use, pieces of lumber of similar mechanical properties are placed in categories called stress grades, which are characterized by (a) one or more sorting criteria, (b) a set of...

  12. Better utilization of low-grade woods

    Science.gov (United States)

    Peter Koch

    1957-01-01

    The objective of this paper is threefold: to outline briefly some of the avenues of approach so far employed in utilizing low-grade wood, to comment on the economic aspects of the problem, and finally, to speculate about what developments the future might bring to the field of utilization.

  13. Does Relative Grading help Male Students?

    DEFF Research Database (Denmark)

    Czibor, Eszter; Onderstal, Sander; Sloof, Randolph

    The provision of non-pecuniary incentives in education is a topic that has received much scholarly attention lately. Our paper contributes to this discussion by investigating the effectiveness of grade incentives in increasing student performance. We perform a direct comparison of the two most co...

  14. Ia diastolic dysfunction: an echocardiographic grade.

    Science.gov (United States)

    Pandit, Anil; Mookadam, Farouk; Hakim, Fayaz A; Mulroy, Eoin; Saadiq, Rayya; Doherty, Mairead; Cha, Stephen; Seward, James; Wilansky, Susan

    2015-01-01

    To demonstrate that a distinct group of patients with Grade Ia diastolic dysfunction who do not conform to present ASE/ESE diastolic grading exists. Echocardiographic and demographic data of the Grade Ia diastolic dysfunction were extracted and compared with that of Grades I and II in 515 patients. The mean of age of the cohort was 75 ± 9 years and body mass index did not differ significantly between the 3 groups (P = 0.45). Measurements of left atrial volume index (28.58 ± 7 mL/m(2) in I, 33 ± 10 mL/m(2) in Ia, and 39 ± 12 mL/m(2) in II P Ia, and 79 ± 15 msec in II P Ia, and 217 ± 57 msec in II P Ia, and 22 ± 8 in II), and lateral E/e' (8 ± 3 in I, 15 ± 6 in Ia, and 18 ± 9 in II P Ia compared with I and II. These findings remained significant even after adjusting for age, gender, diabetes, and smoking. Patients with echocardiographic characteristics of relaxation abnormality (E/A ratio of Ia group. © 2014, Wiley Periodicals, Inc.

  15. Quantitative grading of store separation trajectories

    CSIR Research Space (South Africa)

    Jamison, Kevin A

    2017-09-01

    Full Text Available . This paper describes the development of an automated analysis process and software that can run a multitude of separation scenarios. A key enabler for this software is the development of a quantitative grading algorithm that scores the outcome of each release...

  16. Geometry task sheets : grades 3-5

    CERN Document Server

    Rosenberg, Mary

    2009-01-01

    For grades 3-5, our Common Core State Standards-based resource meets the geometry concepts addressed by the NCTM standards and encourages the students to learn and review the concepts in unique ways. Each task sheet is organized around a central problem taken from real-life experiences of the students.

  17. Algebra task sheets : grades pk-2

    CERN Document Server

    Reed, Nat

    2009-01-01

    For grades PK-2, our Common Core State Standards-based resource meets the algebraic concepts addressed by the NCTM standards and encourages the students to learn and review the concepts in unique ways. Each task sheet is organized around a central problem taken from real-life experiences of the students.

  18. Geometry task sheets : grades pk-2

    CERN Document Server

    Rosenberg, Mary

    2009-01-01

    For grades PK-2, our Common Core State Standards-based resource meets the geometry concepts addressed by the NCTM standards and encourages the students to learn and review the concepts in unique ways. Each task sheet is organized around a central problem taken from real-life experiences of the students.

  19. Ferrite grade iron oxides from ore rejects

    Indian Academy of Sciences (India)

    Iron oxyhydroxides and hydroxides were synthesized from chemically beneficiated high SiO2/Al2O3 low-grade iron ore (57.49% Fe2O3) rejects and heated to get iron oxides of 96–99.73% purity. The infrared band positions, isothermal weight loss and thermogravimetric and chemical analysis established the chemical ...

  20. Elementary construction of graded lie groups

    International Nuclear Information System (INIS)

    Scheunert, M.; Rittenberg, V.

    1977-06-01

    We show how the definitions of the classical Lie groups have to be modified in the case where Grassmann variables are present. In particular, we construct the general linear, the special linear and the orthosymplectic graded Lie groups. Special attention is paid to the question of how to formulate an adequate 'unitarity condition'. (orig.) [de

  1. Developing Middle Grades Students' MP3

    Science.gov (United States)

    Tassell, Janet; Stobaugh, Rebecca; Sheffield, Linda

    2011-01-01

    Middle grades are a critical time for capturing the interest and imagination and developing the potential of mathematically promising students. This is a time for students to make sense of mathematics, build a solid foundation and enthusiasm, and set the course for the highest levels of mathematics in the future. This is a time to explore their…

  2. Osteoporosis Risk Factors in Eighth Grade Students.

    Science.gov (United States)

    Lysen, Victoria C.; Walker, Robert

    1997-01-01

    Presents findings from food frequency questionnaires and surveys of 138 Midwestern eighth-grade student-parent pairs. The study examined the incidence of modifiable and nonmodifiable osteoporosis risk factors and compared gender differences. Data analysis indicated that many adolescents possessed several modifiable and nonmodifiable risk factors…

  3. Whale Preservation. Grades Five to Nine.

    Science.gov (United States)

    Racicot, Darlene

    Dedicated to the conservation and preservation of whales, dolphins, and porpoises through public education, this instructional unit for grades 5-9 provides current (1993) facts, lesson plans, activities, and conservation and preservation techniques. Interdisciplinary activities involve students in debates, critical thinking, research, and…

  4. What Can Readers Read after Graded Readers?

    Science.gov (United States)

    McQuillan, Jeff

    2016-01-01

    Nation (2014) concluded that most of the vocabulary one needs to read challenging texts in English can be acquired incidentally through voluminous reading. This study examines possible texts that second language (L2) readers can use to move from controlled-vocabulary materials such as graded readers, which go up through approximately the…

  5. Comparison between two differential graded algebras in ...

    Indian Academy of Sciences (India)

    76

    A differential calculus on a “space” means the specification of a differential graded algebra (dga), often interpreted as space of forms. In classical geometry the “space” is a manifold and we have the de-Rham dga, whereas in noncommutative geometry a “space” is described by a triple called spectral triple. A spectral triple is ...

  6. Helping Your Kid Make the Grade.

    Science.gov (United States)

    Dornbusch, Sandy

    Research indicates that students' activities and relationships with their parents predict grades more surely than parental education, family income, ethnicity, sex, and family structure. Children with extremely permissive parents do not do well and children with extremely authoritarian parents do worse. Inconsistent parenting is even more strongly…

  7. Influence of Hydroxypropyl Methylcellulose Molecular Weight Grade ...

    African Journals Online (AJOL)

    Erah

    weight grades (K4M and K15M) on drug release from diclofenac sodium matrix tablets. Methods: Tablets containing diclofenac ... Keywords: Matrix, Diclofenac sodium, HPMC, Erosion, Water uptake. Received: 12 January 2011 .... incorporating the structure and geometric characteristics of the release device and n is.

  8. Graded-Lie-algebra cohomology and supergravity

    International Nuclear Information System (INIS)

    D'Auria, R.; Fre, P.; Regge, T.

    1980-01-01

    Detailed explanations of the cohomology invoked in the group-manifold approach to supergravity is given. The Chevalley cohomology theory of Lie algebras is extended to graded Lie algebras. The scheme of geometrical theories is enlarged so to include cosmological terms and higher powers of the curvature. (author)

  9. The Returns on Investment Grade Diamonds

    NARCIS (Netherlands)

    Renneboog, L.D.R.

    2013-01-01

    Abstract: This paper examines the risk-return characteristics of investment grade gems (white diamonds, colored diamonds and other types of gems including sapphires, rubies, and emeralds). The transactions are coming from gem auctions and span the period 1999-2012. Over our time frame, the annual

  10. 7 CFR 29.6018 - Grade.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Grade. 29.6018 Section 29.6018 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... to other characteristics when they are of sufficient importance to be treated separately. ...

  11. Examining Teacher Grades Using Rasch Measurement Theory

    Science.gov (United States)

    Randall, Jennifer; Engelhard, George, Jr.

    2009-01-01

    In this study, we present an approach to questionnaire design within educational research based on Guttman's mapping sentences and Many-Facet Rasch Measurement Theory. We designed a 54-item questionnaire using Guttman's mapping sentences to examine the grading practices of teachers. Each item in the questionnaire represented a unique student…

  12. Construction Industry Related Mathematics: Seventh Grade.

    Science.gov (United States)

    Mundell, Scott

    The field tested construction industry-related mathematics unit is intended to familiarize seventh grade students with various facets of the construction industry, including the various occupations available and the mathematical abilities and other skills and training necessary to pursue an occupation in the industry. The final set of activities…

  13. Communications and Media: Grade 7. Cluster II.

    Science.gov (United States)

    Calhoun, Olivia H.

    A curriculum guide for grade 7, the document is devoted to the occupational cluster "Communications and Media." It is divided into six units: advertising, film and photography, radio and television, journalism and publishing, library and periodicals, and transocean communications. Each unit is introduced by a statement of the topic, the…

  14. Environmental Education. Teacher's Handbook, Grade 5.

    Science.gov (United States)

    Nashville - Davidson County Metropolitan Public Schools, TN.

    Prepared for use in the 5th grade, this teacher's handbook consists of 19 science units dealing with environmental education. Topics are ecology, language arts, rocks and fossils, soil, noise pollution, Nashville pioneers and American Indians, conservation, waste and litter, water pollution, compass and mapping, plants and trees, use of the…

  15. Reliability Estimates for Undergraduate Grade Point Average

    Science.gov (United States)

    Westrick, Paul A.

    2017-01-01

    Undergraduate grade point average (GPA) is a commonly employed measure in educational research, serving as a criterion or as a predictor depending on the research question. Over the decades, researchers have used a variety of reliability coefficients to estimate the reliability of undergraduate GPA, which suggests that there has been no consensus…

  16. Grading Practices and Distributions Across Internal Medicine Clerkships.

    Science.gov (United States)

    Fazio, Sara B; Torre, Dario M; DeFer, Thomas M

    2016-01-01

    Clerkship evaluation and grading practices vary widely between U.S. medical schools. Grade inflation continues to exist, and grade distribution is likely to be different among U.S. medical schools. Increasing the number of available grades curtails "grade inflation." A national survey of all Clerkship Directors in Internal Medicine members was administered in 2011. The authors assessed key aspects of grading. Response rate was 76%. Among clerkship directors (CDs), 61% of respondents agreed that grade inflation existed in the internal medicine clerkship at their school, and 43% believed that it helped students obtain better residency positions. With respect to grading practices, 79% of CDs define specific behaviors needed to achieve each grade, and 36% specify an ideal grade distribution. In addition, 44% have a trained core faculty responsible for evaluating students, 35% describe formal grading meetings, and 39% use the Reporter-Interpreter-Manager-Educator (RIME) scheme. Grading scales were described as follows: 4% utilize a pass/fail system, 13% a 3-tier (e.g., Honors/Pass/Fail), 45% 4-tier, 35% 5-tier, and 4% 6+-tier system. There was a trend to higher grades with more tiers available. Grade inflation continues in the internal medicine clerkship. Almost half of CDs feel that this practice assists students to obtain better residency positions. A minority of programs have a trained core faculty who are responsible for evaluation. About one third have formal grading meetings and use the RIME system; both have been associated with more robust and balanced grading practices. In particular, there is a wide variation between schools in the percentage of students who are awarded the highest grade, which has implications for residency applications. Downstream users of clinical clerkship grades must be fully aware of these variations in grading in order to appropriately judge medical student performance.

  17. Histopathologic grading of anaplasia in retinoblastoma.

    Science.gov (United States)

    Mendoza, Pia R; Specht, Charles S; Hubbard, G Baker; Wells, Jill R; Lynn, Michael J; Zhang, Qing; Kong, Jun; Grossniklaus, Hans E

    2015-04-01

    To determine whether the degree of tumor anaplasia has prognostic value by evaluating its correlation with high-risk histopathologic features and clinical outcomes in a series of retinoblastoma patients. Retrospective clinicopathologic study. The clinical and pathologic findings in 266 patients who underwent primary enucleation for retinoblastoma were reviewed. The histologic degree of anaplasia was graded as retinocytoma, mild, moderate, or severe as defined by increasing cellular pleomorphism, number of mitoses, nuclear size, and nuclear hyperchromatism. Nuclear morphometric characteristics were measured. The clinical and pathologic data of 125 patients were compared using Kaplan-Meier estimates of survival. Fisher exact test and multivariate regression were used to analyze the association between anaplasia grade and high-risk histologic features. Increasing grade of anaplasia was associated with decreased overall survival (P = .003) and increased risk of metastasis (P = .0007). Histopathologic features that were associated with anaplasia included optic nerve invasion (P anaplasia grading as predictors of distant metastasis and death showed that high-risk histopathology was statistically significant as an independent predictor (P = .01 for metastasis, P = .03 for death) but anaplasia was not (P = .63 for metastasis, P = .30 for death). In the absence of high-risk features, however, severe anaplasia identified an additional risk for metastasis (P = .0004) and death (P = .01). Grading of anaplasia may be a useful adjunct to standard histopathologic criteria in identifying retinoblastoma patients who do not have high-risk histologic features but still have an increased risk of metastasis and may need adjuvant therapy. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. Processing hot-dip galvanized AHSS grades: a challenging task

    Energy Technology Data Exchange (ETDEWEB)

    Pichler, A.; Hebesberger, T.; Tragl, E.; Traint, S.; Faderl, J.; Angeli, G.; Koesters, K. [voestalpine Stahl GmbH, Linz (Austria)

    2005-07-01

    High-strength thin sheet steel grades have gained a considerable market share. At present a very strong demand has been observed for DP (dual-phase), CP (complex phase) and TRIP grades, which are often summarized as advanced high-strength steel grades (AHSS). The potential benefits of applying AHSS grades were impressively demonstrated in the ULSAC-AVC project, in which a remarkable reduction in mass and an increase in stiffness and crash safety were achieved by using a very high share of AHSS steel grades. The present contribution concentrates on hot-dip galvanized AHSS thin sheet grades. The hot-dip galvanizeability of such grades is critically discussed after an overview is provided of the metallurgy of AHSS grades, including microstructure, mechanical properties, phase transformations and required alloy design. Based on these fundamentals, the processing of AHSS grades in the hot-dip galvanizing line is discussed and the resulting properties presented. (orig.)

  19. The effect of grades on the preference effect : Grading reduces consideration of disconfirming evidence

    NARCIS (Netherlands)

    Hayek, A.S.; Toma, C.; Oberlé, D.; Butera, F.

    2014-01-01

    The tendency to look for evidence that supports, rather than questions, one's viewpoint (preference effect) is a pervasive phenomenon. Although one important goal of education is developing critical thinking, the widespread practice of grading might discourage students in appreciating disconfirming

  20. A Comparison of Air Force Field Grade and Company Grade Officer Leadership

    National Research Council Canada - National Science Library

    Enrequez, Arnel

    1998-01-01

    ...), indicating that empirical development of a similar model for the USAF should be feasible. The purpose of this study was to determine differences in importance of leadership behaviors between AF company grade officers (CGOs), majors (O-4s...

  1. Will bottle-grade PET demand lure fiber-grade capacity?

    International Nuclear Information System (INIS)

    Coeyman, M.

    1993-01-01

    As demand for bottle-grade polyethylene terephthalate (PET) continues strong and new capacity hastens to meet it, some industry observers wonder if conversions to bottle-grade from fiber-grade capacity will become an industry trend. Taiwan's Nan Ya Plastics was recently said to be considering such a switch, but company sources say it has no such plans. Peter Driscoll, senior partner at PCI Fibres ampersand Raw Materials (Crawley, UK), says that while it is true that demand for the bottle-grade material remains unsatisfied, he doubts that many conversions will take place. You must remember, says Driscoll, that it is not always possible to switch, and that even where it is possible there are limitations

  2. High-grade and low-grade gliomas: differentiation by using perfusion MR imaging

    International Nuclear Information System (INIS)

    Hakyemez, B.; Erdogan, C.; Ercan, I.; Ergin, N.; Uysal, S.; Atahan, S.

    2005-01-01

    AIM: Relative cerebral blood volume (rCBV) is a commonly used perfusion magnetic resonance imaging (MRI) technique for the evaluation of tumour grade. Relative cerebral blood flow (rCBF) has been less studied. The goal of our study was to determine the usefulness of these parameters in evaluating the histopathological grade of the cerebral gliomas. METHODS: This study involved 33 patients (22 high-grade and 11 low-grade glioma cases). MRI was performed for all tumours by using a first-passage gadopentetate dimeglumine T2*-weighted gradient-echo single-shot echo-planar sequence followed by conventional MRI. The rCBV and rCBF were calculated by deconvolution of an arterial input function. The rCBV and rCBF ratios of the lesions were obtained by dividing the values obtained from the normal white matter of the contralateral hemisphere. For statistical analysis Mann-Whitney testing was carried out. A p value of less than 0.05 indicated a statistically significant difference. Receiver operating characteristic curve (ROC) analysis was performed to assess the relationship between the rCBV and rCBF ratios and grade of gliomas. Their cut-off value permitting discrimination was calculated. The correlation between rCBV and CBF ratios and glioma grade was assessed using Pearson correlation analysis. RESULTS: In high-grade gliomas, rCBV and rCBF ratios were measured as 6.50±4.29 and 3.32±1.87 (mean±SD), respectively. In low-grade gliomas, rCBV and rCBF ratios were 1.69±0.51 and 1.16±0.38, respectively. The rCBV and rCBF ratios for high-grade gliomas were statistically different from those of low-grade gliomas (p 0.05). The cut-off value was taken as 1.98 in the rCBV ratio and 1.25 in the rCBF ratio. There was a strong correlation between the rCBV and CBF ratios (Pearson correlation = 0.830, p<0.05). CONCLUSION: Perfusion MRI is useful in the preoperative assessment of the histopathologicalal grade of gliomas; the rCBF ratio in addition to the rCBV ratio can be incorporated

  3. Concomitant glenohumeral pathologies associated with acute and chronic grade III and grade V acromioclavicular joint injuries.

    Science.gov (United States)

    Jensen, Gunnar; Millett, Peter J; Tahal, Dimitri S; Al Ibadi, Mireille; Lill, Helmut; Katthagen, Jan Christoph

    2017-08-01

    The purpose of this study was to identify the risk of concomitant glenohumeral pathologies with acromioclavicular joint injuries grade III and V. Patients who underwent arthroscopically-assisted stabilization of acromioclavicular joint injuries grade III or grade V between 01/2007 and 12/2015 were identified in the patient databases of two surgical centres. Gender, age at index surgery, grade of acromioclavicular joint injury (Rockwood III or Rockwood V), and duration between injury and index surgery (classified as acute or chronic) were of interest. Concomitant glenohumeral pathologies were noted and their treatment was classified as debridement or reconstructive procedure. A total of 376 patients (336 male, 40 female) were included. Mean age at time of arthroscopic acromioclavicular joint reconstruction surgery was 42.1 ± 14.0 years. Overall, 201 patients (53%) had one or more concomitant glenohumeral pathologies. Lesions of the biceps tendon complex and rotator cuff were the most common. Forty-five patients (12.0%) had concomitant glenohumeral pathologies that required an additional repair. The remaining 156 patients (41.5%) received a debridement of their concomitant pathologies. Rockwood grade V compared to Rockwood grade III (p = 0.013; odds ratio 1.7), and chronic compared to acute injury were significantly associated with having a concomitant glenohumeral pathology (p = 0.019; odds ratio 1.7). The probability of having a concomitant glenohumeral pathology was also significantly associated with increasing age (p acromioclavicular joint injury of either grade III or V. Twenty-two percent of these patients with concomitant glenohumeral pathologies received an additional dedicated repair procedure. Although a significant difference in occurrence of concomitant glenohumeral pathologies was seen between Rockwood grades III and V, and between acute and chronic lesions, increasing age was identified as the most dominant predictor. Level IV, case series.

  4. Improving reading in the primary grades.

    Science.gov (United States)

    Duke, Nell K; Block, Meghan K

    2012-01-01

    Almost fifteen years have passed since the publication of the National Research Council's seminal report Preventing Reading Difficulties in Young Children, which provided research-based recommendations on what could be done to better position students in prekindergarten through third grade for success in grade four and above. This article by Nell Duke and Meghan Block first examines whether specific key recommendations from the report have been implemented in U.S. classrooms. They find that recommendations regarding increased access to kindergarten and greater attention to and improvement of students' word-reading skills have been widely adopted. Others have not. Vocabulary and comprehension, long neglected in the primary grades, still appear to be neglected. Contrary to the report's recommendations, attention to building conceptual and content knowledge in science and social studies has actually decreased in the past fifteen years. In other words, the easier-to-master skills are being attended to, but the broader domains of accomplishment that constitute preparation for comprehension and learning in the later grades--vocabulary knowledge, comprehension strategy use, and conceptual and content knowledge--are being neglected. Near stagnation in fourth-grade students' comprehension achievement is thus unsurprising. The authors then turn to research and reviews of research on improving primary-grade reading published since 1998, when Preventing Reading Difficulties was issued. They discuss several instructional approaches identified as effective in improving word-reading skill, vocabulary and conceptual knowledge, comprehension strategies, and reading outside of school; they discuss advances in interventions for struggling readers, and in whole-school literacy reform. Duke and Block then identify three key obstacles that have prevented widespread adoption of these best practices in teaching reading. The first obstacle is a short-term orientation toward instruction and

  5. INAA of polyacrylic hydrogels of pharmaceutical grade

    International Nuclear Information System (INIS)

    Ponta, C.; Salagean, M.; Pantelica, A.; Georgescu, I.I.

    1998-01-01

    Polyacrylic acid (PA) and its salts are promising biomaterials used in the pharmaceutical industry. They could be used as pharmaceutical additives, as a burn dressing and also in the slow released implants or trans-derma patch formulations. Polyacrylic acid of pharmaceutical grade can be obtained by gamma irradiation polymerization. The influence of the raw materials and of the technological procedure on the final product purity has been investigated by Instrumental Neutron Activation Analysis (INAA) method. The following materials have been analyzed by INAA: 1) acrylic acid of technical grade; 2) acrylic acid purified by double crystallisation; 3) NaOH of analytical grade; 4) CaCl-2·6H 2 O of pharmaceutical grade; 5) CaCl 2 ·2H 2 O of analytical grade; 6) granulated PANa; 7) ungranulated PANa; 8) ungranulated PANaCa; 9) PANaCa granulated by milling in IFIN-HH using the mill nr. 1; 10) PANaCa granulated by milling in Institute of Chemical and Pharmaceutical Research (ICPR); 11) PANaCa granulated by milling in IFIN-HH using the mill nr. 2. The first five samples, marked from 1 to 5, are raw materials and the other six samples, marked from 6 to 11, are the final polyacrylic structures processed by various technological procedures. The samples together with the appropriate reference materials have been irradiated at WWR-S reactor in a neutron flux of 2.5·10 12 cm -2 s -1 and the induced radioactivity was registered by a HPGe detector (EG/G ORTEC) of 30% efficiency and 2.1 keV resolution. The concentrations of As, Br, Ce, Co, Cr, Fe, La, Sb, Sc, Zn have been determined. For the final polyacrylic structures, except for granulated PANa (sample 6), only the elements Co, Cr, Fe, Sc, Zn were found at the following concentration levels: tens of ppm (Co), ppm (Zn), hundreds of ppb (Cr), tens of ppb (Co), ppb (Co, Sc), 10 -1 ppb (Sc). In the granulated PANa, in comparison with the other analyzed final products, similar concentration values were found for Fe, Sc and Zn

  6. Comparison of non-electrophoresis grade with electrophoresis grade BIS in NIPAM polymer gel preparation

    Science.gov (United States)

    Khodadadi, Roghayeh; Khajeali, Azim; Farajollahi, Ali Reza; Hajalioghli, Parisa; Raeisi, Noorallah

    2015-01-01

    Introduction:The main objective of this study was to investigate the possibility of replacing electrophoresis cross-linker with non-electrophoresis N, N′-methylenebisacrylamide (BIS) in N-isopropyl acrylamide (NIPAM) polymer gel and its possible effect on dose response. Methods: NIPAM polymer gel was prepared from non-electrophoresis grade BIS and the relaxation rate (R2) was measured by MR imaging after exposing the gel to gamma radiation from Co-60 source. To compare the response of this gel with the one that contains electrophoresis grade BIS, two sets of NIPAM gel were prepared using electrophoresis and non-electrophoresis BIS and irradiated to different gamma doses. Results: It was found that the dose–response of NIPAM gel made from the non-electrophoresis grade BIS is coincident with that of electrophoresis grade BIS. Conclusion:Taken all, it can be concluded that the non-electrophoresis grade BIS not only is a suitable alternative for the electrophoresis grade BIS but also reduces the cost of gel due to its lower price. PMID:26457250

  7. Comparison of cartilage thickness with radiologic grade of knee osteoarthritis

    International Nuclear Information System (INIS)

    Agnesi, Filippo; Amrami, Kimberly K.; Frigo, Carlo A.; Kaufman, Kenton R.

    2008-01-01

    To compare joint space width (JSW) measurements obtained from magnetic resonance imaging (MRI) with a semi-automated computer algorithm to the Kellgren and Lawrence grading of osteoarthritis (OA). Three hundred and six patients (234 female, 72 male) with a mean age of 56.7 years (range 31-81 years) underwent MRI of their knees with a fast oblique spiral spoiled gradient (SPGR) sequence. A board-certified musculoskeletal radiologist graded the OA of all the patients in accordance with the Kellgren and Lawrence OA scale. A previously validated computer algorithm was used to determine the minimum JSW for both the tibiofemoral joint and the patellofemoral joint. An analysis of variance (ANOVA) with the Student-Newman-Kuels post-hoc test was used to determine if there were differences in JSW as a function of OA grade. The radiologic grade of OA was inversely associated with the JSW. In the medial compartment the JSW did not change significantly between grade 1 and grade 2, but there was a significant decrease in JSW between grade 0 (normal) and grade 1 and for each OA grade above grade 2. In the lateral compartment no statistical differences were found till grade 2, while grade 3 was found to be statistically different from the previous one. The number of patients with a grade 4 patellofemoral OA was too low for the statistical significance to be assessed. In the patellofemoral joint the JSW did not change significantly until grade 2, while a statistically significant reduction was found for both grade 3 and grade 4. This study showed that an inverse non-linear relationship exists between radiologic grade and JSW. The relationship differs for the tibiofemoral and the patellofemoral joint. (orig.)

  8. Comparison of cartilage thickness with radiologic grade of knee osteoarthritis

    Energy Technology Data Exchange (ETDEWEB)

    Agnesi, Filippo [Mayo Clinic, Motion Analysis Laboratory, Division of Orthopedic Research, Rochester, MN (United States); Polytechnic of Milan, Department of Bioengineering, Milan (Italy); Amrami, Kimberly K. [Mayo Clinic, Department of Radiology, Rochester, MN (United States); Frigo, Carlo A. [Polytechnic of Milan, Department of Bioengineering, Milan (Italy); Kaufman, Kenton R. [Mayo Clinic, Motion Analysis Laboratory, Division of Orthopedic Research, Rochester, MN (United States); Mayo Clinic/Foundation, Motion Analysis Laboratory, Department of Orthopedic Surgery, Rochester, MN (United States)

    2008-07-15

    To compare joint space width (JSW) measurements obtained from magnetic resonance imaging (MRI) with a semi-automated computer algorithm to the Kellgren and Lawrence grading of osteoarthritis (OA). Three hundred and six patients (234 female, 72 male) with a mean age of 56.7 years (range 31-81 years) underwent MRI of their knees with a fast oblique spiral spoiled gradient (SPGR) sequence. A board-certified musculoskeletal radiologist graded the OA of all the patients in accordance with the Kellgren and Lawrence OA scale. A previously validated computer algorithm was used to determine the minimum JSW for both the tibiofemoral joint and the patellofemoral joint. An analysis of variance (ANOVA) with the Student-Newman-Kuels post-hoc test was used to determine if there were differences in JSW as a function of OA grade. The radiologic grade of OA was inversely associated with the JSW. In the medial compartment the JSW did not change significantly between grade 1 and grade 2, but there was a significant decrease in JSW between grade 0 (normal) and grade 1 and for each OA grade above grade 2. In the lateral compartment no statistical differences were found till grade 2, while grade 3 was found to be statistically different from the previous one. The number of patients with a grade 4 patellofemoral OA was too low for the statistical significance to be assessed. In the patellofemoral joint the JSW did not change significantly until grade 2, while a statistically significant reduction was found for both grade 3 and grade 4. This study showed that an inverse non-linear relationship exists between radiologic grade and JSW. The relationship differs for the tibiofemoral and the patellofemoral joint. (orig.)

  9. Production of nuclear grade zirconium: A review

    Energy Technology Data Exchange (ETDEWEB)

    Xu, L., E-mail: L.Xu-2@tudelft.nl [School of Materials Science and Metallurgy, Northeastern University, Shenyang 110004 (China); Department of Materials Science and Engineering, Delft University of Technology, Delft 2628 CD (Netherlands); Xiao, Y. [Department of Metallurgical Engineering, Anhui University of Technology, Ma' anshan 243002 (China); Zr-Hf-Ti Metallurgie B.V., Den Haag 2582 SB (Netherlands); Sandwijk, A. van [Zr-Hf-Ti Metallurgie B.V., Den Haag 2582 SB (Netherlands); Xu, Q. [School of Materials Science and Metallurgy, Northeastern University, Shenyang 110004 (China); Yang, Y. [Department of Materials Science and Engineering, Delft University of Technology, Delft 2628 CD (Netherlands)

    2015-11-15

    Zirconium is an ideal material for nuclear reactors due to its low absorption cross-section for thermal neutrons, whereas the typically contained hafnium with strong neutron-absorption is very harmful for zirconium as a fuel cladding material. This paper provides an overview of the processes for nuclear grade zirconium production with emphasis on the methods of Zr–Hf separation. The separation processes are roughly classified into hydro- and pyrometallurgical routes. The known pyrometallurgical Zr–Hf separation methods are discussed based on the following reaction features: redox characteristics, volatility, electrochemical properties and molten salt–metal equilibrium. In the present paper, the available Zr–Hf separation technologies are compared. The advantages and disadvantages as well as future directions of research and development for nuclear grade zirconium production are discussed.

  10. A low-grade extraskeletal osteosarcoma

    Energy Technology Data Exchange (ETDEWEB)

    Okada, Kyoji; Ito, Hiroki; Miyakoshi, Naohisa; Itoi, Eiji [Department of Orthopedic Surgery, Akita University School of Medicine, 1-1-1 Hondo, Akita 010-8543 (Japan); Sageshima, Masato [Department of Clinical Pathology, Akita University Hospital, 1-1-1 Hondo, Akita 010-8543 (Japan); Nishida, Jun [Department of Orthopedic Surgery, Iwate Medical School, 19-1 Uchimaru, Morioka 020-8505 (Japan)

    2003-03-01

    The case of a 35-year-old woman with low-grade extraskeletal osteosarcoma of the left leg is presented. Radiographs showed peripheral ossification of the lesion, suggesting myositis ossificans. Most of the tumor was composed of cartilage, and the cellularity and cell atypia of the proliferating chondrocytes were mild to moderate. In the periphery, bone formation with a relatively clear margin and proliferation of spindle cells with minimal nuclear atypia were observed. The average percentage of cells positive for MIB-1 was 9.0%. A diagnosis of low-grade extraskeletal osteosarcoma was made on the basis of these histologic findings. The clinical course 47 months after a wide excision was uneventful. (orig.)

  11. Probabilistic Modeling of Graded Timber Material Properties

    DEFF Research Database (Denmark)

    Faber, M. H.; Köhler, J.; Sørensen, John Dalsgaard

    2004-01-01

    The probabilistic modeling of timber material characteristics is considered with special emphasis to the modeling of the effect of different quality control and selection procedures used as means for quality grading in the production line. It is shown how statistical models may be established...... on the basis of the same type of information which is normally collected as a part of the quality control procedures and furthermore, how the efficiency of different control procedures may be quantified and compared. The tail behavior of the probability distributions of timber material characteristics plays...... such that they may readily be applied in structural reliability analysis and their format appears to be appropriate for codification purposes of quality control and selection for grading procedures....

  12. Grading of vesicoureteral reflux by radionuclide cystography

    International Nuclear Information System (INIS)

    Fretzayas, A.; Karpathios, T.; Dimitriou, P.; Nicolaidou, P.; Matsaniotis, N.

    1984-01-01

    Thirty-six children with urinary tract infection aged 6 months to 14 years (mean age 4 1/2 years) were studied sequentially using direct radionuclide (RNC) and conventional voiding cystourethrography (VCU). Vesicoureteral reflux (VUR) was detected equally well by both methods. Twenty-seven refluxing ureters were found by RNC, 23 by VCU and 22 by both methods. Radiologic grade of reflux may be determined approximately with the isotope technique from the volume of regurgitating urine und duration of reflux, at a much decreased radiation exposure. Residual urine was also measured by RNC and found to be higher in children with VUR. RNC is a reliable method for detecting and grading VUR and should effectively replace VCU as the follow-up examination of choice. (orig.)

  13. Buckling Response of Thick Functionally Graded Plates

    Directory of Open Access Journals (Sweden)

    BOUAZZA MOKHTAR

    2014-11-01

    Full Text Available In this paper, the buckling of a functionally graded plate is studied by using first order shear deformation theory (FSDT. The material properties of the plate are assumed to be graded continuously in the direction of thickness. The variation of the material properties follows a simple power-law distribution in terms of the volume fractions of constituents. The von Karman strains are used to construct the equilibrium equations of the plates subjected to two types of thermal loading, linear temperature rise and gradient through the thickness are considered. The governing equations are reduced to linear differential equation with boundary conditions yielding a simple solution procedure. In addition, the effects of temperature field, volume fraction distributions, and system geometric parameters are investigated. The results are compared with the results of the no shear deformation theory (classic plate theory, CPT.

  14. Cognition Effects of Low-Grade Hypoxia

    Science.gov (United States)

    2016-07-01

    human short-term memory . Br J Anaesth. 1971; 43(6):548–552. 3. Crow TJ, Kelman GR. Psychological effects of mild acute hypoxia. Br J Anaesth. 1973; 45...Journal Article 3. DATES COVERED (From – To) Jan 2003 – Sep 2005 4. TITLE AND SUBTITLE Cognition Effects of Low-Grade Hypoxia 5a. CONTRACT NUMBER... cognitive function are reported in this paper. The study compared cognitive function during short exposures at four different altitudes. Ninety-one

  15. Fracture Analysis of Functionally Graded Materials

    International Nuclear Information System (INIS)

    Zhang, Ch.; Gao, X. W.; Sladek, J.; Sladek, V.

    2010-01-01

    This paper reports our recent research works on crack analysis in continuously non-homogeneous and linear elastic functionally graded materials. A meshless boundary element method is developed for this purpose. Numerical examples are presented and discussed to demonstrate the efficiency and the accuracy of the present numerical method, and to show the effects of the material gradation on the crack-opening-displacements and the stress intensity factors.

  16. Different grades MEMS accelerometers error characteristics

    Science.gov (United States)

    Pachwicewicz, M.; Weremczuk, J.

    2017-08-01

    The paper presents calibration effects of two different MEMS accelerometers of different price and quality grades and discusses different accelerometers errors types. The calibration for error determining is provided by reference centrifugal measurements. The design and measurement errors of the centrifuge are discussed as well. It is shown that error characteristics of the sensors are very different and it is not possible to use simple calibration methods presented in the literature in both cases.

  17. New examples of continuum graded Lie algebras

    International Nuclear Information System (INIS)

    Savel'ev, M.V.

    1989-01-01

    Several new examples of continuum graded Lie algebras which provide an additional elucidation of these algebras are given. Here, in particular, the Kac-Moody algebras, the algebra S 0 Diff T 2 of infinitesimal area-preserving diffeomorphisms of the torus T 2 , the Fairlie, Fletcher and Zachos sine-algebras, etc., are described as special cases of the cross product Lie algebras. 8 refs

  18. Vibration of Elastic Functionally Graded Thick Rings

    Directory of Open Access Journals (Sweden)

    Guang-Hui Xu

    2017-01-01

    Full Text Available The free vibration behaviors of functionally graded rings were investigated theoretically. The material graded in the thickness direction according to the power law rule and the rings were assumed to be in plane stress and plane strain states. Based on the first-order shear deformation theory and the kinetic relation of von Kárman type, the frequency equation for free vibration of functionally graded ring was derived. The derived results were verified by those in literatures which reveals that the present theory can be appropriate to predict the free vibration characteristics for quite thick rings with the radius-to-thickness ratio from 60 down to 2.09. Comparison between the plane stress case and the plane strain case indicates a slight difference. Meanwhile, the effects of the structural dimensional parameters and the material inhomogeneous parameter are examined. It is interesting that the value of the logarithmic form of vibration frequency is inversely proportional to the logarithmic form of the radius-to-thickness ratio or the mean radius.

  19. Uranium production from low grade Swedish shale

    International Nuclear Information System (INIS)

    Carlsson, O.

    1977-01-01

    In view of the present nuclear programmes a steep increase in uranium demand is foreseen which will pose serious problems for the uranium industry. The annual additions to uranium ore reserves must almost triple within the next 15 years in order to support the required production rates. Although there are good prospects for the discovery of further conventional deposits of uranium there is a growing interest in low grade uranium deposits. Large quantities of uranium exist in black shales, phosphates, granites, sea water and other unconventional sources. There are however factors which limit the utilization of these low grade materials. These factors include the extraction costs, the environmental constrains on mining and milling of huge amounts of ore, the development of technologies for the beneficiation of uranium and, in the case of very low grade materials, the energy balance. The availability of by-product uranium is limited by the production rate of the main product. The limitations differ very much according to types of ores, mining and milling methods and the surroundings. As an illustration a description is given of the Swedish Ranstad uranium shale project, its potential, constraints and technical solutions

  20. Automated Essay Grading using Machine Learning Algorithm

    Science.gov (United States)

    Ramalingam, V. V.; Pandian, A.; Chetry, Prateek; Nigam, Himanshu

    2018-04-01

    Essays are paramount for of assessing the academic excellence along with linking the different ideas with the ability to recall but are notably time consuming when they are assessed manually. Manual grading takes significant amount of evaluator’s time and hence it is an expensive process. Automated grading if proven effective will not only reduce the time for assessment but comparing it with human scores will also make the score realistic. The project aims to develop an automated essay assessment system by use of machine learning techniques by classifying a corpus of textual entities into small number of discrete categories, corresponding to possible grades. Linear regression technique will be utilized for training the model along with making the use of various other classifications and clustering techniques. We intend to train classifiers on the training set, make it go through the downloaded dataset, and then measure performance our dataset by comparing the obtained values with the dataset values. We have implemented our model using java.

  1. A vision of graded hemispheric specialization.

    Science.gov (United States)

    Behrmann, Marlene; Plaut, David C

    2015-11-01

    Understanding the process by which the cerebral hemispheres reach their mature functional organization remains challenging. We propose a theoretical account in which, in the domain of vision, faces and words come to be represented adjacent to retinotopic cortex by virtue of the need to discriminate among homogeneous exemplars. Orthographic representations are further constrained to be proximal to typically left-lateralized language-related information to minimize connectivity length between visual and language areas. As reading is acquired, orthography comes to rely more heavily (albeit not exclusively) on the left fusiform region to bridge vision and language. Consequently, due to competition from emerging word representations, face representations that were initially bilateral become lateralized to the right fusiform region (albeit, again, not exclusively). We review recent research that describes constraints that give rise to this graded hemispheric arrangement. We then summarize empirical evidence from a variety of studies (behavioral, evoked response potential, functional imaging) across different populations (children, adolescents, and adults; left handers and individuals with developmental dyslexia) that supports the claims that hemispheric lateralization is graded rather than binary and that this graded organization emerges dynamically over the course of development. Perturbations of this system either during development or in adulthood provide further insights into the principles governing hemispheric organization. © 2015 New York Academy of Sciences.

  2. Volume Equalization Method for Land Grading Design: Uniform ...

    African Journals Online (AJOL)

    muğla üniversitesi

    2011-05-23

    May 23, 2011 ... *Corresponding author. E-mail: ... Land grading has been in practice for a long time, but land-grading ... method was based on least-squares theory and he showed its ... Srinisava (1996) developed a nonlinear optimization.

  3. Comparative evaluation of six cytological grading systems in breast carcinoma

    Directory of Open Access Journals (Sweden)

    Kaushik Saha

    2013-01-01

    Conclusions: Robinson′s grading system is simple, more objective and reproducible, and demonstrated the best concordance with histological grading. So, Robinson′s system should be used routinely for breast carcinoma aspirates.

  4. Relation between grade and abundance of manganese nodules

    Digital Repository Service at National Institute of Oceanography (India)

    Sudhakar, M.

    Data from more than 1000 locations in the Central Indian Ocean Basin (CIOB) where both bulk nodule chemistry and abundance were determined and utilized to study the relationship between grade and abundance of manganese nodule deposits. Grade...

  5. A Quantitative Study on the Correlation between Grade Span Configuration of Sixth Grade Students in Private Florida Schools and Academic Achievement on Standardized Achievement Scores

    Science.gov (United States)

    Rantin, Deborah

    2017-01-01

    The applied dissertation was designed to investigate the three models of grade span configurations of sixth grade and the effects grade span configuration has on results of the standardized achievement scores of sixth grade students in private, Florida schools. Studies that have been conducted on sixth grade students and grade span configuration…

  6. Tumor grade-related thallium-201 uptake in chondrosarcomas

    International Nuclear Information System (INIS)

    Kaya, G.C.; Demir, Y.; Ozkal, S.

    2010-01-01

    Diagnosis of low-grade chondrosarcoma, especially discrimination between enchondroma and low-grade chondrosarcoma, may be difficult pathologically. The aim of this study was to evaluate the value of thallium-201 (Tl-201) scintigraphy in the diagnosis of chondrosarcoma and to investigate whether there was a correlation between Tl-201 uptake and tumor grade. We retrospectively evaluated 121 patients with pathologically proven bone and soft tissue tumors diagnosed between the years 1999 and 2007. All patients were followed by the Bone and Soft Tissue Tumor Working Group in our hospital. Twenty-three patients, mean age 44±15 (range 17-72) years, with a diagnosis of cartilaginous tumors were included. Increased Tl-201 uptake at the lesion sites greater than background was evaluated as malignant tumor. For the pathologic classification, a grading system (grade 1-3) based on the histopathologic findings was used. Pearson correlation coefficient was used to determine whether there was any correlation between Tl-201 uptake and tumor grade in chondrosarcoma. There were 7 enchondromas and 16 chondrosarcomas. Four of 16 patients with chondrosarcoma had lesions pathologically classified as grade 3, 5 as grade 2, and 7 had grade 1 chondrosarcoma. Increased Tl-201 uptake was observed in all patients with grade 3 chondrosarcoma and 2 patients with grade 2 chondrosarcoma. Of 10 patients with chondrosarcoma, 3 grade 2 chondrosarcomas and 7 grade 1 chondrosarcomas, there was no Tl-201 uptake in the tumor region. A significant correlation was found between Tl-201 uptake and tumor grade in chondrosarcoma (p=0.002, r=0.71). Only a few reports in literature have demonstrated false negative results in low-grade chondrosarcoma. Tl-201 uptake was related to tumor grade in chondrosarcoma. If there is a possibility of chondrosarcoma, Tl-201 scintigraphy should be reported with caution. (author)

  7. Determination of sieve grading curves using an optical device

    OpenAIRE

    PHAM, AM; DESCANTES, Yannick; DE LARRARD, François

    2011-01-01

    The grading curve of an aggregate is a fundamental characteristic for mix design that can easily be modified to adjust several mix properties. While sieve analysis remains the reference method to determine this curve, optical devices are developing, allowing easier and faster assessment of aggregate grading. Unfortunately, optical grading results significantly differ from sieve grading curves. As a consequence, getting full acceptance of these new methods requires building bridges between the...

  8. Grading options for western hemlock "pulpwood" logs from southeastern Alaska.

    Science.gov (United States)

    David W. Green; Kent A. McDonald; John Dramm; Kenneth Kilborn

    Properties and grade yield are estimated for structural lumber produced from No. 3, No. 4, and low-end No. 2 grade western hemlock logs of the type previously used primarily for the production of pulp chips. Estimates are given for production in the Structural Framing, Machine Stress Rating, and Laminating Stock grading systems. The information shows that significant...

  9. Preliminary work in developing sawbolt grading systems for white oak

    Science.gov (United States)

    Everette D. Rast; Everette D. Rast

    1971-01-01

    This paper is principally a description of one technique used in the development of white oak (Quercus alba L.) sawbolt grades--not a final sawbolt grading system for the species over its range. This technique can be used by anyone in developing other bolt-grade specifications or in refining the system presented in this paper.

  10. Extensive Graded Reading in the Liberal Arts and Sciences

    Science.gov (United States)

    Poulshock, Joseph

    2010-01-01

    For this research, learners did extensive graded reading (EGR) with traditional graded readers, and they also interacted with short graded stories in the liberal arts and sciences (LAS). This study describes the purpose and format of the LAS stories used by hundreds of university students and adult learners in Japan. It summarizes the results of…

  11. The Relationship between Attendance Policies and Student Grades

    Science.gov (United States)

    Aaron, Michael D.

    2012-01-01

    The relationship between attendance policies and student grades in college courses was investigated. Specifically, a calculated grade point average was determined for all academic classes taught at Shelton State Community College between 2000 and 2008. These grade point averages were compared descriptively and statistically in an effort to…

  12. 49 CFR 80.11 - Investment-grade ratings.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Investment-grade ratings. 80.11 Section 80.11... § 80.11 Investment-grade ratings. (a) At the time a project sponsor submits an application, the DOT... investment-grade rating. (b) The full funding of a secured (direct) loan, loan guarantee, or line of credit...

  13. Collegiate Grading Practices and the Gender Pay Gap

    Directory of Open Access Journals (Sweden)

    Alicia C. Dowd

    2000-01-01

    Full Text Available Extending research findings by R. Sabot and J. Wakeman-Linn (1991, this article presents a theoretical analysis showing that relatively low grading quantitative fields and high grading verbal fields create a disincentive for college women to invest in quantitative study. Pressures on grading practices are modeled using higher education production functions.

  14. Collegiate Grading Practices and the Gender Pay Gap.

    Science.gov (United States)

    Dowd, Alicia C.

    2000-01-01

    Presents a theoretical analysis showing that relatively low grading quantitative fields and high grading verbal fields create a disincentive for college women to invest in quantitative study. Extends research by R. Sabot and J. Wakeman-Linn. Models pressures on grading practices using higher education production functions. (Author/SLD)

  15. 7 CFR 52.1855 - Grades of Sultana raisins.

    Science.gov (United States)

    2010-01-01

    ... § 52.1855 Grades of Sultana raisins. (a) “U.S. Grade A” is the quality of Sultana Raisins that have... in Table IV of this subpart. (b) “U.S. Grade B” is the quality of Sultana Raisins that have similar... than materially affected. Grit, sand, or silt None of any consequence may be present that affects the...

  16. Choosing the Adequate Level of Graded Readers--Preliminary Study

    Science.gov (United States)

    Prtljaga, Jelena; Palinkaševic, Radmila; Brkic, Jovana

    2015-01-01

    Graded readers have been used as second language teaching material since the end of the Second World War. They are an important source of simplified material which provides comprehensible input on all levels. It is of crucial importance for a successful usage of graded readers in the classroom and in studies which focus on graded readers, that an…

  17. The Effects of Framing Grades on Student Learning and Preferences

    Science.gov (United States)

    Bies-Hernandez, Nicole J.

    2012-01-01

    Two experiments examined whether framing effects, in terms of losses and gains, can be extended to student learning and grading preferences. In Experiment 1, participants rated psychology course syllabi to investigate preferences for differently framed grading systems: a loss versus gain grading system. The results showed a clear framing effect…

  18. Machine grading of lumber : practical concerns for lumber producers

    Science.gov (United States)

    William L. Galligan; Kent A. McDonald

    2000-01-01

    Machine lumber grading has been applied in commercial operations in North America since 1963, and research has shown that machine grading can improve the efficient use of wood. However, industry has been reluctant to apply research findings without clear evidence that the change from visual to machine grading will be a profitable one. For instance, mill managers need...

  19. The Causal Effects of Grade Retention on Behavioral Outcomes

    Science.gov (United States)

    Martorell, Paco; Mariano, Louis T.

    2018-01-01

    This study examines the impact of grade retention on behavioral outcomes under a comprehensive assessment-based student promotion policy in New York City. To isolate the causal effect of grade retention, we implement a fuzzy regression discontinuity (RD) design that exploits the fact that grade retention is largely determined by whether a student…

  20. Illusions of a Good Grade: Effort or Luck?

    Science.gov (United States)

    Buckelew, Susan P.; Byrd, Nikki; Key, Colin W.; Thornton, Jessica; Merwin, Michelle M.

    2013-01-01

    This study assessed the relationships among the accuracy of grade predictions, actual grades, self-enhancement bias, and attributions about academic performance. As a group, students anticipated higher grades than were earned. Individual differences in self-enhancement bias were measured using the discrepancy between anticipated and attained…

  1. Influence of "Halo" and "Demon" Effects in Subjective Grading.

    Science.gov (United States)

    Gibb, Gerald D.

    1983-01-01

    The phenomenon of "halo" effects in subjective grading was investigated. Two groups of three raters evaluated 20 term papers in introductory psychology. Term paper grades correlated significantly with course grades when information about previous academic performance was made available. When this information was not available, the…

  2. Grading Homework to Emphasize Problem-Solving Process Skills

    Science.gov (United States)

    Harper, Kathleen A.

    2012-01-01

    This article describes a grading approach that encourages students to employ particular problem-solving skills. Some strengths of this method, called "process-based grading," are that it is easy to implement, requires minimal time to grade, and can be used in conjunction with either an online homework delivery system or paper-based homework.

  3. Grading sacroiliitis with emphasis on MRI imaging; Grading der Sakroiliitis mit Betonung der MRT-Bildgebung

    Energy Technology Data Exchange (ETDEWEB)

    Jurik, A.G.; Egund, N. [The Department of Radiology R, Aarhus Kommunehospital (Denmark)

    2004-03-01

    Cross-sectional imaging techniques play a decisive role in identification, localization, and characterization of alterations in the sacroiliac joint during the early stage of seronegative spondylarthropathy (SpA). Although several studies showed that the diagnostic capabilities of MRI and CT are superior to those of conventional radiography, they have not yet become established and accepted as methods for evaluating the grade of ankylosing spondylitis (AS) in contrast to conventional radiography. The lack of acceptance for MRI and/or CT methods for evaluating and grading changes in the sacroiliac joint makes it difficult to include the results of these procedures in classifying the grade of SpA. Moreover, grading the changes in the sacroiliac joint in SpA with a method more sensitive than conventional radiography will be of prime importance in assessing treatment, e.g., the efficacy of new biological therapeutic agents directed against the tumor necrosis factor-alpha (TNF-{alpha}). An overview of the available grading methods is provided and MRI and CT techniques are presented. (orig.) [German] Schnittbildverfahren spielen bei der Identifizierung, Lokalisation und Charakterisierung von Veraenderungen des Sakroiliakalgelenks (SIG) im Fruehstadium der seronegativen Spondylarthropathie (SpA) eine entscheidende Rolle. Obwohl mehrere Studien zeigten, dass der diagnostische Wert der MRT und CT jenem der konventionellen Radiographie ueberlegen ist, hat sich das Schnittbildverfahren als Mittel zur Evaluierung des Grades der ankylosierenden Spondylitis (AS) im Gegensatz zur konventionellen Radiographie noch nicht etabliert und durchgesetzt. Dieses Fehlen eines akzeptierten MRT- und/oder CT-Verfahrens zur Evaluierung und zum Grading der Veraenderungen am SIG macht es schwierig, die Ergebnisse dieser Verfahren bei der Einstufung des Grades der AS-Veraenderungen und Erarbeitung von Diagnosekriterien fuer andere Formen der SpA einzubeziehen. Ausserdem wird das Grading der SIG

  4. Cognitive impairments in patients with low grade gliomas and high grade gliomas

    Directory of Open Access Journals (Sweden)

    Eliane C. Miotto

    2011-08-01

    Full Text Available OBJECTIVE: The relationship between brain tumors and cognitive deficits is well established in the literature. However, studies investigating the cognitive status in low and high-grade gliomas patients are scarce, particularly in patients with average or lower educational level. This study aimed at investigating the cognitive functioning in a sample of patients with low and high-grade gliomas before surgical intervention. METHOD: The low-grade (G1, n=19 and high-grade glioma (G2, n=8 patients underwent a detailed neuropsychological assessment of memory, executive functions, visuo-perceptive and visuo-spatial abilities, intellectual level and language. RESULTS: There was a significant impairment on verbal and visual episodic memory, executive functions including mental flexibility, nominal and categorical verbal fluency and speed of information processing in G2. G1 showed only specific deficits on verbal and visual memory recall, mental flexibility and processing speed. CONCLUSION: These findings demonstrated different levels of impairments in the executive and memory domains in patients with low and high grade gliomas.

  5. Working memory and individual differences in mathematics achievement: A longitudinal study from first grade to second grade

    OpenAIRE

    De Smedt, Bert; Janssen, Rianne; Bouwens, Kelly; Verschaffel, Lieven; Boets, Bart; Ghesquière, Pol

    2009-01-01

    This longitudinal study examined the relationship between working memory and individual differences in mathematics. Working memory measures, comprising the phonological loop, the visuospatial sketchpad, and the central executive, were administered at the start of first grade. Mathematics achievement was assessed 4 months later (at the middle of first grade) and 1 year later (at the start of second grade). Working memory was significantly related to mathematics achievement in both grades, show...

  6. Girls' Spatial Skills and Arithmetic Strategies in First Grade as Predictors of Fifth-Grade Analytical Math Reasoning

    Science.gov (United States)

    Casey, Beth M.; Lombardi, Caitlin McPherran; Pollock, Amanda; Fineman, Bonnie; Pezaris, Elizabeth

    2017-01-01

    This study investigated longitudinal pathways leading from early spatial skills in first-grade girls to their fifth-grade analytical math reasoning abilities (N = 138). First-grade assessments included spatial skills, verbal skills, addition/subtraction skills, and frequency of choice of a decomposition or retrieval strategy on the…

  7. HYPERGLYCEMIA IN GRADE III AND GRADE IV MALNUTRITION WITH DEHYDRATING GASTROENTERITIS

    Directory of Open Access Journals (Sweden)

    Mallesh

    2015-07-01

    Full Text Available OBJECTIVE OF THE STUDY: To study the incidence of hyperglycemia in grade III AND IV malnutrition with no signs and some signs of dehydration. SETTING: Tertiary care center located in north Karnataka. DESIGN: Prospective observational study involving 21 children. METHODS: All the children with grade III and grade IV malnutrition presenting with diarrhea of less than 14 days duration, having no signs to some signs of dehydration. RESULTS: Hyperglycemia was observed in three of 21 children hypoglycemia was observed in six children. CONCLUSION: Although hypoglycemia is common finding in moderate and severely malnourished children with dehydrating gastroenteritis, hyperglycemia should also be suspected and treated. Long term follow up of these children is needed involving larger number of people in multicenter studies.

  8. Clinical management of grade III oligodendroglioma

    Directory of Open Access Journals (Sweden)

    Simonetti G

    2015-07-01

    Full Text Available G Simonetti, P Gaviani, A Botturi, A Innocenti, E Lamperti, A Silvani Neurooncology Unit, Fondazione IRCCS Istituto Neurologico Carlo Besta, Milan, Italy Abstract: Oligodendrogliomas represent the third most common type of glioma, comprising 4%–15% of all gliomas and can be classified by degree of malignancy into grade II and grade III, according to WHO classification. Only 30% of oligodendroglial tumors have anaplastic characteristics. Anaplastic oligodendroglioma (AO is often localized as a single lesion in the white matter and in the cortex, rarely in brainstem or spinal cord. The management of AO is deeply changed in the recent years. Maximal safe surgical resection followed by radiotherapy (RT was considered as the standard of care since paramount findings regarding molecular aspects, in particular co-deletion of the short arm of chromosome 1 and the long arm of chromosome 19, revealed that these subsets of AO, benefit in terms of overall survival (OS and progression-free survival (PFS, from the addition of chemotherapy to RT. Allelic losses of chromosomes 1p and 19q occur in 50%–70% of both low-grade and anaplastic tumors, representing a strong prognostic factor and a powerful predictor of prolonged survival. Several other molecular markers have potential clinical significance as IDH1 mutations, confirming the strong prognostic role for OS. Malignant brain tumors negatively impacts on patients' quality of life. Seizures, visual impairment, headache, and cognitive disorders can be present. Moreover, chemotherapy and RT have important side effects. For these reasons, “health-related quality of life” is becoming a topic of growing interest, investigating on physical, mental, emotional, and social well-being. Understanding the impact of medical treatment on health-related quality of life will probably have a growing effect both on health care strategies and on patients. Keywords: anaplastic oligodendroglioma, radiotherapy, chemotherapy

  9. Low grade gastric MALT lymphoma: Radiographic findings

    International Nuclear Information System (INIS)

    Brown, J.A.; Carson, B.W.; Gascoyne, R.D.; Cooperberg, P.L.; Connors, J.M.; Mason, A.C.

    2000-01-01

    AIMS: Gastric MALT (mucosa-associated lymphoid tissue) lymphoma is now recognized as a distinct entity within extranodal non-Hodgkin's lymphoma. The purpose of this study was to describe the radiographic findings in low grade gastric MALT lymphoma. MATERIALS AND METHODS: We retrospectively reviewed the radiographic findings in 22 cases of low-grade gastric MALT lymphoma. The study group consisted of 15 men and seven women (median age 68 years, range 41-91 years). Lesions were designated as infiltrative or polypoid by consensus of two radiologists. Polypoid lesions were categorized by number and size. Anatomical site within the stomach and presence of transpyloric or oesophagogastric extension was determined for each case. The presence of abdominal lymphadenopathy was categorized as regional or distant. The presence of Helicobacter pylori was determined from endoscopic and surgical biopsies. RESULTS: Computed tomography (CT) revealed abnormalities of the stomach in 19 cases of the 21 in which it was performed. There were 14 infiltrative lesions and five polypoid lesions. Of the 14 infiltrative lesions, the mean gastric wall thickness was 2.2 cm (range 0.8-6.0 cm). There were three single and two multiple polypoid lesions (mean size 2.2 cm, range 1.5-2.7 cm). Transpyloric extension was observed in two cases and oesophagogastric extension in one. Abdominal lymphadenopathy was observed in 10 of 21 patients. Helicobacter pylori was found in 19 of 22 cases (86%). CONCLUSION: Low grade B cell gastric MALT lymphomas present with an infiltrative form on CT in about three-quarters of cases and a polypoid pattern in the remainder. Abdominal lymphadenopathy is seen in approximately one-half of cases. There is a high association with Helicobacter pylori. Brown, J.A. 2000. Clinical Radiology 55, 384-389

  10. Clinical management of grade III oligodendroglioma

    International Nuclear Information System (INIS)

    Simonetti, G; Gaviani, P; Botturi, A; Innocenti, A; Lamperti, E; Silvani, A

    2015-01-01

    Oligodendrogliomas represent the third most common type of glioma, comprising 4%–15% of all gliomas and can be classified by degree of malignancy into grade II and grade III, according to WHO classification. Only 30% of oligodendroglial tumors have anaplastic characteristics. Anaplastic oligodendroglioma (AO) is often localized as a single lesion in the white matter and in the cortex, rarely in brainstem or spinal cord. The management of AO is deeply changed in the recent years. Maximal safe surgical resection followed by radiotherapy (RT) was considered as the standard of care since paramount findings regarding molecular aspects, in particular co-deletion of the short arm of chromosome 1 and the long arm of chromosome 19, revealed that these subsets of AO, benefit in terms of overall survival (OS) and progression-free survival (PFS), from the addition of chemotherapy to RT. Allelic losses of chromosomes 1p and 19q occur in 50%–70% of both low-grade and anaplastic tumors, representing a strong prognostic factor and a powerful predictor of prolonged survival. Several other molecular markers have potential clinical significance as IDH1 mutations, confirming the strong prognostic role for OS. Malignant brain tumors negatively impacts on patients’ quality of life. Seizures, visual impairment, headache, and cognitive disorders can be present. Moreover, chemotherapy and RT have important side effects. For these reasons, “health-related quality of life” is becoming a topic of growing interest, investigating on physical, mental, emotional, and social well-being. Understanding the impact of medical treatment on health-related quality of life will probably have a growing effect both on health care strategies and on patients

  11. EDF specifications on nuclear grade resins

    International Nuclear Information System (INIS)

    Mascarenhas, Darren; Gressier, Frederic; Taunier, Stephane; Le-Calvar, Marc; Ranchoux, Gilles; Marteau, Herve; Labed, Veronique

    2012-09-01

    Ion exchange resins are widely used across EDF, especially within the nuclear division for the purification of water. Important applications include primary circuit, secondary circuit and effluent treatment, which require high quality nuclear grade resins to retain the dissolved species, some of which may be radioactive. There is a need for more and more efficient purification in order to decrease worker dose during maintenance but also to decrease volumes of radioactive resin waste. Resin performance is subject to several forms of degradation, including physical, chemical, thermal and radioactive, therefore appropriate resin properties have to be selected to reduce such effects. Work has been done with research institutes, manufacturers and on EDF sites to select these properties, create specifications and to continuously improve on these specifications. An interesting example of research regarding resin performance is the resin degradation under irradiation. Resins used in the CVCS circuit of EDF nuclear power plants are subject to irradiation over their lifetime. A study was carried out on the effects of total integrated doses of 0.1, 1 and 10 MGy on typically used EDF mixed bed resins in a 'mini-CVCS' apparatus to simultaneously test actual primary circuit fluid. The tests confirmed that the resins still perform efficiently after a typical CVCS radiation dose. Certain resins also need additional specifications in order to maintain the integrity of the particular circuits they are used in. Recently, EDF has updated its requirements on these high purity nuclear grade resins, produced generic doctrines for all products and materials used on site which include resins of all grades, and as a result have also updated a guide on recommended resin usage for the French fleet of reactors. An overview of the evolutions will be presented. (authors)

  12. Low-grade salivary duct carcinoma or low-grade intraductal carcinoma? Review of the literature.

    Science.gov (United States)

    Kuo, Ying-Ju; Weinreb, Ilan; Perez-Ordonez, Bayardo

    2013-07-01

    Low-grade salivary duct carcinoma (LG-SDC) is a rare neoplasm characterized by predominant intraductal growth, luminal ductal phenotype, bland microscopic features, and favorable clinical behavior with an appearance reminiscent of florid to atypical ductal hyperplasia to low grade intraductal breast carcinoma. LG-SDC is composed of multiple cysts, cribriform architecture with "Roman Bridges", "pseudocribriform" proliferations with floppy fenestrations or irregular slits, micropapillae with epithelial tufts, fibrovascular cores, and solid areas. Most of the tumor cells are small to medium sized with pale eosinophilic cytoplasm, and round to oval nuclei, which may contain finely dispersed or dark condensed chromatin. Foci of intermediate to high grade atypia, and invasive carcinoma or micro-invasion have been reported in up to 23 % of cases. The neoplastic cells have a ductal phenotype with coexpression of keratins and S100 protein and are surrounded by a layer of myoepithelial cells in non-invasive cases. The main differential diagnosis of LG-SDC includes cystadenoma, cystadenocarcinoma, sclerosing polycystic adenosis, salivary duct carcinoma in situ/high-grade intraductal carcinoma, and papillary-cystic variant of acinic cell carcinoma. There is no published data supporting the continuous classification of LG-SDC as a variant of cystadenocarcinoma. Given that most LG-SDC are non-invasive neoplasms; the terms "cribriform cystadenocarcinoma" and LG-SDC should be replaced by "low-grade intraductal carcinoma" (LG-IDC) of salivary gland or "low-grade intraductal carcinoma with areas of invasive carcinoma" in those cases with evidence of invasive carcinoma.

  13. Do class size effects differ across grades?

    DEFF Research Database (Denmark)

    Nandrup, Anne Brink

    size cap that creates exogenous variation in class sizes. Significant (albeit modest) negative effects of class size increases are found for children on primary school levels. The effects on math abilities are statistically different across primary and secondary school. Larger classes do not affect......This paper contributes to the class size literature by analyzing whether short-run class size effects are constant across grade levels in compulsory school. Results are based on administrative data on all pupils enroled in Danish public schools. Identification is based on a government-imposed class...

  14. Contemporary management of high-grade gliomas.

    Science.gov (United States)

    Sim, Hao-Wen; Morgan, Erin R; Mason, Warren P

    2018-01-01

    High-grade gliomas, including glioblastoma, are the most common malignant brain tumors in adults. Despite intensive efforts to develop new therapies for these diseases, treatment options remain limited and prognosis is poor. Recently, there have been important advances in our understanding of the molecular basis of glioma, leading to refinements in our diagnostic and management approach. There is new evidence to guide the treatment of elderly patients. A multitude of new agents have been investigated, including targeted therapies, immunotherapeutics and tumor-treating fields. This review summarizes the key findings from this research, and presents a perspective on future opportunities to advance the field.

  15. The Fracture Toughness of Nuclear Graphites Grades

    Energy Technology Data Exchange (ETDEWEB)

    Burchell, Timothy D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Erdman, III, Donald L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lowden, Rick R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hunter, James A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hannel, Cara C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-04-01

    New measurements of graphite mode I critical stress intensity factor, KIc (commonly referred to as the fracture toughness) and the mode II critical shear stress intensity, KIIc, are reported and compared with prior data for KIc and KIIc. The new data are for graphite grades PCEA, IG-110 and 2114. Variations of KIc and acoustic emission (AE) data with graphite texture are reported and discussed. The Codes and Standards applications of fracture toughness, KIc, data are also discussed. A specified minimum value for nuclear graphite KIc is recommended.

  16. [The WHO/ISUP grading system for renal carcinoma].

    Science.gov (United States)

    Moch, H

    2016-07-01

    Histological tumor grading is an accepted prognostic parameter of renal cell carcinoma (RCC). In 2012, the International Society of Urologic Pathologists (ISUP) proposed a novel grading system for RCC, mainly based on the evaluation of nucleoli: grade 1 tumors have nucleoli that are inconspicuous and basophilic at ×400 magnification; grade 2 tumors have nucleoli that are clearly visible at ×400 magnification and eosinophilic; grade 3 tumors have clearly visible nucleoli at ×100 magnification; and grade 4 tumors have extreme pleomorphism or rhabdoid and/or sarcomatoid morphology. This grading system was validated for clear cell renal cell carcinoma and papillary renal cell carcinoma. At the same time, the ISUP proposed not grading chromophobe renal cell carcinomas according to this system. At a consensus conference in Zurich the World Health Organization (WHO) recommended the ISUP grading system; thus, the WHO/ISUP grading system is now going to be implemented internationally. The ISUP/WHO grading system has not been validated as a prognostic parameter for other tumor subtypes, but can be used for descriptive purposes.

  17. Development of an automatic visual grading system for grafting seedlings

    Directory of Open Access Journals (Sweden)

    Subo Tian

    2017-01-01

    Full Text Available In this study, a visual grading system of vegetable grafting machine was developed. The study described key technology of visual grading system of vegetable grafting machine. First, the contrasting experiment was conducted between acquired images under blue background light and natural light conditions, with the blue background light chosen as lighting source. The Visual C++ platform with open-source computer vision library (Open CV was used for the image processing. Subsequently, maximum frequency of total number of 0-valued pixels was predicted and used to extract the measurements of scion and rootstock stem diameters. Finally, the developed integrated visual grading system was experimented with 100 scions and rootstock seedlings. The results showed that success rate of grading reached up to 98%. This shows that selection and grading of scion and rootstock could be fully automated with this developed visual grading system. Hence, this technology would be greatly helpful for improving the grading accuracy and efficiency.

  18. Aeroelastic Tailoring of a Plate Wing with Functionally Graded Materials

    Science.gov (United States)

    Dunning, Peter D.; Stanford, Bret K.; Kim, H. Alicia; Jutte, Christine V.

    2014-01-01

    This work explores the use of functionally graded materials for the aeroelastic tailoring of a metallic cantilevered plate-like wing. Pareto trade-off curves between dynamic stability (flutter) and static aeroelastic stresses are obtained for a variety of grading strategies. A key comparison is between the effectiveness of material grading, geometric grading (i.e., plate thickness variations), and using both simultaneously. The introduction of material grading does, in some cases, improve the aeroelastic performance. This improvement, and the physical mechanism upon which it is based, depends on numerous factors: the two sets of metallic material parameters used for grading, the sweep of the plate, the aspect ratio of the plate, and whether the material is graded continuously or discretely.

  19. Comparison of the reliability of two hydronephrosis grading systems: The Society for Foetal Urology grading system vs. the Onen grading system

    International Nuclear Information System (INIS)

    Kim, S.-Y.; Kim, M.-J.; Yoon, C.S.; Lee, M.S.; Han, K.H.; Lee, M.-J.

    2013-01-01

    Aim: To compare the reliability of the conventional ultrasonography grading system for hydronephrosis as suggested by the Society for Fetal Urology (SFU) in 1993 and that developed by Onen in 2007. Materials and methods: One hundred and eighty kidneys in 90 paediatric patients were assessed by four radiologists using each of the two grading systems twice. The SFU system was graded 0–4 (0 = no hydronephrosis; 1 = visualized only renal pelvis; 2 = plus a few caliceal dilatation; 3 = all calyceal dilatation; 4 = plus parenchymal thinning). The Onen system was graded 0–4 (0 = no hydronephrosis; 1 = only renal pelvic dilatation; 2 = plus caliceal dilatation; 3 = plus 50% renal parenchymal loss). Cohen's kappa statistic was used to estimate intra- and interobserver agreement. The weighted least-squares approach was used to compare the intra-observer agreement, and bootstrapping was used to compare the interobserver agreement between the two systems. Results: Intra-observer agreement was substantial to almost perfect in both the SFU (κ 0.79–0.95) and the Onen (κ 0.66–0.97) grading system without difference. The overall interobserver agreement was substantial in both the SFU (κ 0.61–0.68) and the Onen (κ 0.66–0.76) grading system. However, interobserver agreement was fair to moderate for SFU grades 1 and 2 and Onen grades 2 and 3. Conclusion: Both the SFU and Onen grading system are reliable with good intra- and interobserver agreement. However, decreased interobserver agreement was demonstrated for SFU grades 1 and 2 and Onen grades 2 and 3

  20. Current treatment of low grade astrocytoma

    DEFF Research Database (Denmark)

    Pedersen, Christina Louise; Romner, Bertil

    2013-01-01

    Through a comprehensive review of the current literature, the present article investigates several aspects of low grade astrocytomas (LGA), including prognostic factors, treatment strategies and follow-up regimes. LGA are in general relatively slow-growing primary brain tumours, but they have a v...... effective in discriminating between tumour progression and radiation necrosis. The research into biomarkers is currently limited with regards to their applications in LGA diagnostics, and therefore further studies including larger patient populations are needed.......Through a comprehensive review of the current literature, the present article investigates several aspects of low grade astrocytomas (LGA), including prognostic factors, treatment strategies and follow-up regimes. LGA are in general relatively slow-growing primary brain tumours, but they have...... as the course of disease. The current literature seems to support the idea that treatment with radical tumour resection, where possible, yields better long term outcome for patients with LGA. However, adjuvant therapy is often necessary. Administering early postoperative radiotherapy to patients with partially...

  1. Graded Recombination Layers for Multijunction Photovoltaics

    KAUST Repository

    Koleilat, Ghada I.

    2012-06-13

    Multijunction devices consist of a stack of semiconductor junctions having bandgaps tuned across a broad spectrum. In solar cells this concept is used to increase the efficiency of photovoltaic harvesting, while light emitters and detectors use it to achieve multicolor and spectrally tunable behavior. In series-connected current-matched multijunction devices, the recombination layers must allow the hole current from one cell to recombine, with high efficiency and low voltage loss, with the electron current from the next cell. We recently reported a tandem solar cell in which the recombination layer was implemented using a progression of n-type oxides whose doping densities and work functions serve to connect, with negligible resistive loss at solar current densities, the constituent cells. Here we present the generalized conditions for design of efficient graded recombination layer solar devices. We report the number of interlayers and the requirements on work function and doping of each interlayer, to bridge an work function difference as high as 1.6 eV. We also find solutions that minimize the doping required of the interlayers in order to minimize optical absorption due to free carriers in the graded recombination layer (GRL). We demonstrate a family of new GRL designs experimentally and highlight the benefits of the progression of dopings and work functions in the interlayers. © 2012 American Chemical Society.

  2. Microbial Production of Food Grade Pigments

    Directory of Open Access Journals (Sweden)

    Laurent Dufossé

    2006-01-01

    Full Text Available The controversial topic of synthetic dyes in food has been discussed for many years. The scrutiny and negative assessment of synthetic food dyes by the modern consumer have raised a strong interest in natural colouring alternatives. Nature is rich in colours (minerals, plants, microalgae, etc., and pigment-producing microorganisms (fungi, yeasts, bacteria are quite common. Among the molecules produced by microorganisms are carotenoids, melanins, flavins, quinones, and more specifically monascins, violacein or indigo. The success of any pigment produced by fermentation depends upon its acceptability on the market, regulatory approval, and the size of the capital investment required to bring the product to market. A few years ago, some expressed doubts about the successful commercialization of fermentation-derived food grade pigments because of the high capital investment requirements for fermentation facilities and the extensive and lengthy toxicity studies required by regulatory agencies. Public perception of biotechnology-derived products also had to be taken into account. Nowadays some fermentative food grade pigments are on the market: Monascus pigments, astaxanthin from Xanthophyllomyces dendrorhous, Arpink Red from Penicillium oxalicum, riboflavin from Ashbya gossypii, b-carotene from Blakeslea trispora. The successful marketing of pigments derived from algae or extracted from plants, both as a food colour and a nutritional supplement, reflects the presence and importance of niche markets in which consumers are willing to pay a premium for »all natural ingredients«.

  3. Controlling Thermal Conduction by Graded Materials

    Science.gov (United States)

    Ji, Qin; Huang, Ji-Ping

    2018-04-01

    Manipulating thermal conductivities are fundamentally important for controlling the conduction of heat at will. Thermal cloaks and concentrators, which have been extensively studied recently, are actually graded materials designed according to coordinate transformation approaches, and their effective thermal conductivity is equal to that of the host medium outside the cloak or concentrator. Here we attempt to investigate a more general problem: what is the effective thermal conductivity of graded materials? In particular, we perform a first-principles approach to the analytic exact results of effective thermal conductivities of materials possessing either power-law or linear gradation profiles. On the other hand, by solving Laplace’s equation, we derive a differential equation for calculating the effective thermal conductivity of a material whose thermal conductivity varies along the radius with arbitrary gradation profiles. The two methods agree with each other for both external and internal heat sources, as confirmed by simulation and experiment. This work provides different methods for designing new thermal metamaterials (including thermal cloaks and concentrators), in order to control or manipulate the transfer of heat. Support by the National Natural Science Foundation of China under Grant No. 11725521, by the Science and Technology Commission of Shanghai Municipality under Grant No. 16ZR1445100

  4. Diabetic Retinopathy Grading by Digital Curvelet Transform

    Directory of Open Access Journals (Sweden)

    Shirin Hajeb Mohammad Alipour

    2012-01-01

    Full Text Available One of the major complications of diabetes is diabetic retinopathy. As manual analysis and diagnosis of large amount of images are time consuming, automatic detection and grading of diabetic retinopathy are desired. In this paper, we use fundus fluorescein angiography and color fundus images simultaneously, extract 6 features employing curvelet transform, and feed them to support vector machine in order to determine diabetic retinopathy severity stages. These features are area of blood vessels, area, regularity of foveal avascular zone, and the number of micro-aneurisms therein, total number of micro-aneurisms, and area of exudates. In order to extract exudates and vessels, we respectively modify curvelet coefficients of color fundus images and angiograms. The end points of extracted vessels in predefined region of interest based on optic disk are connected together to segment foveal avascular zone region. To extract micro-aneurisms from angiogram, first extracted vessels are subtracted from original image, and after removing detected background by morphological operators and enhancing bright small pixels, micro-aneurisms are detected. 70 patients were involved in this study to classify diabetic retinopathy into 3 groups, that is, (1 no diabetic retinopathy, (2 mild/moderate nonproliferative diabetic retinopathy, (3 severe nonproliferative/proliferative diabetic retinopathy, and our simulations show that the proposed system has sensitivity and specificity of 100% for grading.

  5. Effect of Retention in Elementary Grades on Grade 9 Motivation for Educational Attainment

    Science.gov (United States)

    Cham, Heining; Hughes, Jan N.; West, Stephen G.; Im, Myung Hee

    2014-01-01

    This study investigated the effect of grade retention in elementary school on students’ motivation for educational attainment in grade 9. We equated retained and promoted students on 67 covariates assessed in grade 1 through propensity score weighting. Retained students (31.55%, nretained = 177) and continuously promoted students (68.45%, npromoted = 384) were compared on the bifactor model of motivation for educational attainment (Cham, Hughes, West, & Im, 2014). This model consists of a General factor (student’s overall motivation for educational attainment), and three specific factors: student perceived Teacher Educational Expectations, Peer Educational Aspirations, and Value of Education. Measurement invariance between retained and promoted groups was established. Retained students scored significantly higher than promoted students on each specific factor but not on the General factor. Results showed that the retained and promoted students did not significantly differ on the General factor. The retained students had significantly higher scores on each specific factor than the promoted students. The results suggested that grade retention may not have the negative effects so widely assumed in the published literature; it is an expensive intervention with minimal evidence of benefits to the retained student. PMID:25636258

  6. Grade determination of crumb rubber-modified performance graded asphalt binder.

    Science.gov (United States)

    2013-08-01

    Due to particulates common in crumb rubber-modified asphalt binders, conventional PG grading using the Dynamic : Shear Rheometer (DSR) with a gap height of 1.0 mm may not be valid and in accordance with current specifications. : Asphalt binder testin...

  7. Navigating middle grades: role of social contexts in middle grade school climate.

    Science.gov (United States)

    Kim, Ha Yeon; Schwartz, Kate; Cappella, Elise; Seidman, Edward

    2014-09-01

    During early adolescence, most public school students undergo school transitions, and many students experience declines in academic performance and social-emotional well-being. Theories and empirical research have highlighted the importance of supportive school environments in promoting positive youth development during this period of transition. Despite this, little is known about the proximal social and developmental contexts of the range of middle grade public schools US students attend. Using a cross-sectional dataset from the eighth grade wave of the Early Childhood Longitudinal Study-Kindergarten Cohort 1998-1999, the current study examines the middle grade school social context from the perspectives of administrators and teachers in public schools with typical grade configurations (k-8 schools, middle schools, and junior high schools) and how it relates to students' perceptions of school climate. We find that administrators and teachers in k-8 schools perceive a more positive school social context, controlling for school structural and demographic characteristics. This school social context, in turn, is associated with students' perceptions of their schools' social and academic climate. Implications for educational policy and practice are discussed.

  8. Effect of retention in elementary grades on grade 9 motivation for educational attainment.

    Science.gov (United States)

    Cham, Heining; Hughes, Jan N; West, Stephen G; Im, Myung Hee

    2015-02-01

    This study investigated the effect of grade retention in elementary school on students' motivation for educational attainment in grade 9. We equated retained and promoted students on 67 covariates assessed in grade 1 through propensity score weighting. Retained students (31.55%, nretained=177) and continuously promoted students (68.45%, npromoted=384) were compared on the bifactor model of motivation for educational attainment (Cham, Hughes, West & Im, 2014). This model consists of a General factor (student's overall motivation for educational attainment), and three specific factors: student perceived Teacher Educational Expectations, Peer Educational Aspirations, and Value of Education. Measurement invariance between retained and promoted groups was established. Retained students scored significantly higher than promoted students on each specific factor but not on the General factor. Results showed that the retained and promoted students did not significantly differ on the General factor. The retained students had significantly higher scores on each specific factor than those of the promoted students. The results suggested that grade retention may not have the negative effects so widely assumed in the published literature; it is an expensive intervention with minimal evidence of benefits to the retained student. Copyright © 2014 Society for the Study of School Psychology. Published by Elsevier Ltd. All rights reserved.

  9. Sample Grade Level Benchmarks, Grades 5-8, Based on the 1998 Arkansas State Mathematics Framework.

    Science.gov (United States)

    Arkansas State Dept. of Education, Little Rock.

    This document presents the application and use of mathematics learning proposed by the Arkansas curriculum frameworks for grades 5-8. The standards are presented in chart form and organized into five strands: (1) number sense, properties, and operations; (2) geometry and spatial sense; (3) measurement; (4) data analysis, statistics, and…

  10. Interference studies with two hospital-grade and two home-grade glucose meters.

    Science.gov (United States)

    Lyon, Martha E; Baskin, Leland B; Braakman, Sandy; Presti, Steven; Dubois, Jeffrey; Shirey, Terry

    2009-10-01

    Interference studies of four glucose meters (Nova Biomedical [Waltham, MA] StatStrip [hospital grade], Roche Diagnostics [Indianapolis, IN] Accu-Chek Aviva [home grade], Abbott Diabetes Care [Alameda, CA] Precision FreeStyle Freedom [home grade], and LifeScan [Milpitas, CA] SureStep Flexx [hospital grade]) were evaluated and compared to the clinical laboratory plasma hexokinase reference method (Roche Hitachi 912 chemistry analyzer). These meters were chosen to reflect the continuum of care from hospital to home grade meters commonly seen in North America. Within-run precision was determined using a freshly prepared whole blood sample spiked with concentrated glucose to give three glucose concentrations. Day-to-day precision was evaluated using aqueous control materials supplied by each vendor. Common interferences, including hematocrit, maltose, and ascorbate, were tested alone and in combination with one another on each of the four glucose testing devices at three blood glucose concentrations. Within-run precision for all glucose meters was glucose meters. Ascorbate caused differences (percentage change from a sample without added interfering substances) of >5% with pyrroloquinolinequinone (PQQ)-glucose dehydrogenase-based technologies (Aviva and Freestyle) and the glucose oxidase-based Flexx meter. Maltose strongly affected the PQQ-glucose dehydrogenase-based meter systems. When combinations of interferences (ascorbate, maltose, and hematocrit mixtures) were tested, the extent of the interference was up to 193% (Aviva), 179% (FreeStyle), 25.1% (Flexx), and 5.9% (StatStrip). The interference was most pronounced at low glucose (3.9-4.4 mmol/L). All evaluated glucose meter systems demonstrated varying degrees of interference by hematocrit, ascorbate, and maltose mixtures. PQQ-glucose dehydrogenase-based technologies showed greater susceptibility than glucose oxidase-based systems. However, the modified glucose oxidase-based amperometric method (Nova StatStrip) was

  11. Peer Grading in Astronomy Massive Open Online Course

    Science.gov (United States)

    Formanek, Martin; Wenger, Matthew; Impey, Christopher; Buxner, Sanlyn

    In this work we thoroughly investigate the peer grading process as it happened in the University of Arizona session based MOOC ``Astronomy: Exploring Time and Space'' offered during Spring 2015 through Coursera. Overall, 25400 learners from over 100 countries registered for this course. Of those, 14900 accessed at least one part of the course and 1332 users engaged in the peer grading. First of all we provide description of the peer graded assignments and we identify trends in behavior of people who participated in these exercises. E.g. time they spent on grading, number of assignments graded and patterns arising from comparing all three assignments. Furthermore, for the second assignment, we graded random sample of 300 essays by a group of trained undergraduate students and a group consisting of one of the course instructors together with graduate TAs and we compared results with grades from the peer grading. Specifically we look on Intraclass Correlation Coefficients for all three groups of graders to determine reliability of each group and correlations between final grades. Finally we assess factors influencing reliability of the peer graders participating in the MOOC based on the difference from our grades. This research was supported by Howard Hughes Medical Institute Grant No. 415580.

  12. Role of cytologic grading in prognostication of invasive breast carcinoma

    Directory of Open Access Journals (Sweden)

    Khan Nazoora

    2009-01-01

    Full Text Available Background: Evaluation of cytologic features is indispensable in the preoperative diagnosis and grading of infiltrating ductal breast carcinoma (CA in fine-needle aspiration cytology (FNAC material and this method can also provide additional information regarding intrinsic features of the tumor as well as its prognosis. Aim: This study has been done to evaluate comparatively the cytologic and histomorphologic grading of infiltrating ductal carcinoma of breast with specific reference to lymph node metastasis and its role in prognostication. Materials and Methods: Forty three patients who underwent FNAC and mastectomy for infiltrating ductal carcinoma were cytologically and histologically graded (employing Robinson′s cytologic grading system and Elston′s modification of Bloom-Richardson system, respectively. Statistical analysis was done employing ′z′ test and c2 test to compare the two grading system and to examine the degree of correlation between the cytologic and histologic grades. Multiple regression analysis was done to assess the significance of every cytologic and histologic parameter. All 43 cases, graded cyto-histologically were also evaluated for presence or absence of metastasis to the regional lymph nodes employing c2 test. Results: With histologic grade taken as the standard, cytology was found to be fairly comparable, for grading breast carcinoma (overall sensitivity 89.1%, specificity 100%. Further comparison of the two grading systems by Z-test showed that difference between the cytologic and histologic grading was insignificant in all the three grade (p > 0.05. Of the six parameters studied, cell dissociation, nucleoli and chromatin pattern were the most influential features (p < 0.001. The statistically significant difference (p < 0.001 was found in incidences of axillary lymph node metastatic rate in three cytologic grades (15.4% in grade I vs. 83.3% in grade III as well. Conclusions: Apart from being simple and

  13. Growth of optical grade germanium crystals

    International Nuclear Information System (INIS)

    Waris, M.; Akhtar, M.J.; Mehmood, N.; Ashraf, M.; Siddique, M.

    2011-01-01

    A novel design of Czochralski( CZ ) growth station in a low frequency induction furnace is described and growth of optical grade Ge crystal as a test material is performed achieving a flat solid-liquid interface shape. Grown Ge crystals are annealed in air at 450 -500 deg. C for 4 hrs and then characterized by determination of crystallographic orientation by Laue (back-reflection of X-rays) method, dislocation density studies by etch-pits formation, measuring electrical resistivity by 4-probe technique, conductivity type determination by hot probe method, measurement of hardness on Moh's scale and optical transmission measurement in IR region. The results obtained are compared to those reported in the literature. The use of this growth station for other materials is suggested. (author)

  14. On graded algebras of global dimension 3

    International Nuclear Information System (INIS)

    Piontkovskii, D I

    2001-01-01

    Assume that a graded associative algebra A over a field k is minimally presented as the quotient algebra of a free algebra F by the ideal I generated by a set f of homogeneous elements. We study the following two extensions of A: the algebra F-bar=F/I oplus I/I 2 oplus ... associated with F with respect to the I-adic filtration, and the homology algebra H of the Shafarevich complex Sh(f,F) (which is a non-commutative version of the Koszul complex). We obtain several characterizations of algebras of global dimension 3. In particular, the A-algebra H in this case is free, and the algebra F-bar is isomorphic to the quotient algebra of a free A-algebra by the ideal generated by a so-called strongly free (or inert) set

  15. Is Kindergarten the New First Grade?

    Directory of Open Access Journals (Sweden)

    Daphna Bassok

    2016-01-01

    Full Text Available Recent accounts suggest that accountability pressures have trickled down into the early elementary grades and that kindergarten today is characterized by a heightened focus on academic skills and a reduction in opportunities for play. This paper compares public school kindergarten classrooms between 1998 and 2010 using two large, nationally representative data sets. We show substantial changes in each of the five dimensions considered: kindergarten teachers’ beliefs about school readiness, time spent on academic and nonacademic content, classroom organization, pedagogical approach, and use of standardized assessments. Kindergarten teachers in the later period held far higher academic expectations for children both prior to kindergarten entry and during the kindergarten year. They devoted more time to advanced literacy and math content, teacher-directed instruction, and assessment and substantially less time to art, music, science, and child-selected activities.

  16. Metal recovery from high-grade WEEE

    DEFF Research Database (Denmark)

    Bigum, Marianne; Brogaard, Line Kai-Sørensen; Christensen, Thomas Højlund

    2012-01-01

    . The modeled metallurgical treatment facility included a Kaldo plant, a converter aisle, an anode refinery and a precious metal refinery. The metallurgic treatment showed significant environmental savings when credited the environmental load from avoided production of the same amount of metals by mining...... and refining of ore. The resource recovery per tonne of high-grade WEEE ranged from 2 g of palladium to 386 kg of iron. Quantified in terms of person-equivalents the recovery of palladium, gold, silver, nickel and copper constituted the major environmental benefit of the recovery of metals from WEEE....... These benefits are most likely underestimated in the model, since we did not find adequate data to include all the burdens from mining and refining of ore; burdens that are avoided when metals are recovered from WEEE. The processes connected to the pre-treatment of WEEE were found to have little environmental...

  17. High-grade primary pulmonary leiomyosarcoma

    Directory of Open Access Journals (Sweden)

    Rodrigo Afonso da Silva Sardenberg

    2011-12-01

    Full Text Available Primary sarcomas of the lung are rare and account for 0.5% of all primary lung tumors. There were approximately 300 cases described in the literature as of 2006. All histologic types of sarcoma were described, and the most common intrathoracic types reported were angiosarcoma, leiomyosarcoma, fibrosarcoma, hemangiopericytoma, and rhabdomyosarcoma. The biological behavior of these tumors is not well-known due to their low frequency. Leiomyosarcomas represent one of the most common subtypes encountered in the lungs, and usually occur during the sixth decade, with male predominance. Although the frequency of metastatic disease is not related to tumor size, prognosis was reported to be poorer in high-grade tumors. In comparison with other sarcomas, survival after complete resection of pulmonary leiomyosarcoma was reported as longer. We report on a patient with primary leiomyosarcoma originating from the bronchus with complete resection and long-term follow-up.

  18. Synthesis of battery grade reduced silver powder

    International Nuclear Information System (INIS)

    Qadeer, R.; Hameed, M.; Ikram, S.; Munir, A.

    2002-01-01

    Process for production of battery grade reduced silver powder, an active positive material for zinc-silver oxide batteries, having specific characteristics has been optimized and the synthesized reduced silver powder was characterized. Results reveal that the values of bulk density (1.25 0.1 g/cm3) and activity (73.27 %) of synthesized reduced silver powder lies within the recommended range for use as battery material. It has purity ≥ 98% and contains Fe and Cu as traces in the concentration range of 30 5 ppm and 15 7 ppm respectively. Others determined values of surface and pores parameters are: surface area 2.6 .4 m2/g: pore volume 3.10 cm3/g: pore diameter 0.043 mu m and porosity 20%. XRD studies reveal that reduced silver powder has a cubic structure. (author)

  19. Micromechanical models for graded composite materials

    DEFF Research Database (Denmark)

    Reiter, T; Dvorak, G.J.; Tvergaard, Viggo

    1997-01-01

    of piecewise homogeneous layers with equivalent elastic properties estimated by Mori-Tanaka and self-consistent methods are also analysed under similar boundary conditions. Comparisons of the overall and local fields predicted by the discrete and homogenized models are made using a C/SiC composite system...... fields are predicted by Mori-Tanaka estimates. On the other hand, the response of graded materials with a skeletal microstructure in a wide transition zone between clearly defined matrix phases is better approximated by the self-consistent estimates. Certain exceptions are noted for loading by overall...... transverse shear stress; The results suggest that the averaging methods originally developed for statistically homogeneous aggregates may be selectively applied, with a reasonable degree of confidence, to aggregates dth composition gradients, subjected to both uniform and nonuniform overall loads. (C) 1997...

  20. Laparoscopic adrenalectomy: Gaining experience by graded approach

    Directory of Open Access Journals (Sweden)

    Dalvi Abhay

    2006-01-01

    Full Text Available INTRODUCTION: Laparoscopic adrenalectomy (LA has become a gold standard in management of most of the adrenal disorders. Though report on the first laparoscopic adrenalectomy dates back to 1992, there is no series of LA reported from India. Starting Feb 2001, a graded approach to LA was undertaken in our center. Till March 2006, a total of 34 laparoscopic adrenalectomies were performed with success. MATERIALS AND METHODS: The endocrinology department primarily evaluated all patients. Patients were divided into Group A - unilateral LA and Group B - bilateral LA (BLA. The indications in Group A were pheochromocytoma (n=7, Conn′s syndrome (n=3, Cushing′s adenoma (n=2, incidentaloma (n=2; and in Group B, Cushing′s disease (CD following failed trans-sphenoid pituitary surgery (n = 8; ectopic ACTH- producing Cushing′s syndrome (n=1 and congenital adrenal hyperplasia (CAH (n=1. The lateral transabdominal route was used. RESULTS: The age group varied from 12-54 years, with mean age of 28.21 years. Average duration of surgery in Group A was 166.43 min (40-270 min and 190 min (150- 310 min in Group B. Average blood loss was 136.93 cc (20-400 cc in Group A and 92.5 cc (40-260 cc in Group B. There was one conversion in each group. Mean duration of surgical stay was 1.8 days (1-3 days in Group A and 2.6 days (2-4 days in Group B. All the patients in both groups were cured of their illness. Three patients in Group B developed Nelson′s syndrome. The mean follow up was of 24.16 months (4-61 months. CONCLUSION: LA though technically demanding, is feasible and safe. Graded approach to LA is the key to success.

  1. Terahertz reflectometry imaging for low and high grade gliomas

    Science.gov (United States)

    Ji, Young Bin; Oh, Seung Jae; Kang, Seok-Gu; Heo, Jung; Kim, Sang-Hoon; Choi, Yuna; Song, Seungri; Son, Hye Young; Kim, Se Hoon; Lee, Ji Hyun; Haam, Seung Joo; Huh, Yong Min; Chang, Jong Hee; Joo, Chulmin; Suh, Jin-Suck

    2016-01-01

    Gross total resection (GTR) of glioma is critical for improving the survival rate of glioma patients. One of the greatest challenges for achieving GTR is the difficulty in discriminating low grade tumor or peritumor regions that have an intact blood brain barrier (BBB) from normal brain tissues and delineating glioma margins during surgery. Here we present a highly sensitive, label-free terahertz reflectometry imaging (TRI) that overcomes current key limitations for intraoperative detection of World Health Organization (WHO) grade II (low grade), and grade III and IV (high grade) gliomas. We demonstrate that TRI provides tumor discrimination and delineation of tumor margins in brain tissues with high sensitivity on the basis of Hematoxylin and eosin (H&E) stained image. TRI may help neurosurgeons to remove gliomas completely by providing visualization of tumor margins in WHO grade II, III, and IV gliomas without contrast agents, and hence, improve patient outcomes. PMID:27782153

  2. ALE: Additive Latent Effect Models for Grade Prediction

    OpenAIRE

    Ren, Zhiyun; Ning, Xia; Rangwala, Huzefa

    2018-01-01

    The past decade has seen a growth in the development and deployment of educational technologies for assisting college-going students in choosing majors, selecting courses and acquiring feedback based on past academic performance. Grade prediction methods seek to estimate a grade that a student may achieve in a course that she may take in the future (e.g., next term). Accurate and timely prediction of students' academic grades is important for developing effective degree planners and early war...

  3. Concrete manufacture with un-graded recycled aggregates

    OpenAIRE

    Richardson, Alan; Coventry, Kathryn; Graham, Sue

    2009-01-01

    Purpose – The purpose of this paper is to investigate whether concrete that includes un-graded recycled aggregates can be manufactured to a comparable strength to concrete manufactured from virgin aggregates. \\ud \\ud Design/methodology/approach – A paired comparison test was used to evaluate the difference between concrete made with virgin aggregates (plain control) and concrete including recycled waste. Un-graded construction demolition waste and un-graded ground glass were used as aggregate...

  4. Tumor grading of adult astrocytic glioma on MR imaging

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Kee Hyun; Choi, Choong Gon; Han, Moon Hee; Lee, Seon Kyu [Seoul National University College of Medicine, Seoul (Korea, Republic of); Suh, Jung Ho [Yonsei University College of Medicine, Seoul (Korea, Republic of); Lee, Ho Kyu; Suh, Dae Chul [Ulsan University College of Medicine, Seoul (Korea, Republic of); Choi, Kyu Ho [Catholic University College of Medicine, Seoul (Korea, Republic of); Byun, Hong Sik [Korea Cancer Center Hospital, Seoul (Korea, Republic of); Choi, Woo Suk [Kyung Hee University College of Medicine, Seoul (Korea, Republic of)

    1994-09-15

    The purpose of this study is to determine predictive MR features for grading of astrocytic gliomas and to evaluate the accuracy of MR grading in these tumors. We retrospectively reviewed 135 cases of supratentorial astrocytic gliomas in adult (age > 15 years), all of which were proved by open biopsy. Two observers analysed MR images independently with criteria of margin, edema, mass effect, signal heterogeneity, necrosis, cyst formation, hemorrhage, tumor vascularity, enhancement degree, and enhancement size. The patterns of enhancement were categorized into no, homogeneous, heterogeneous, thin smooth rim, thin irregular rim, and thick irregular rim enhancement patterns. Observers finally diagnosed each case as one of low-grade astrocytoma, anaplastic astrocytoma or glioblastoma multiforme. Statistically significant MR features for grading of these tumors were revealed as necrosis (p < 0.001), edema (0.008), and signal heterogeneity (p < 0.025). When compared with histopathologic grading, MR graded correctly 76%- 77% of cases in two tired system(low-grade astrocytoma versus high-grade astrocytoma), but only 67%-69% of cases in three tiered system(low-grade astrocytoma, anaplastic astrocytoma, glioblastoma multiforme). No contrast enhancement was seen in 45% and 23% of low-grade astrocytoma and anaplastic astrocytoma respectively. Glioblastoma multiforme frequently showed thick irregular rim enhancement (57%), but no enhancement at all in 8%. We have concluded that necrosis and edema are significant predictive MR features for grading of supratentorial astrocytic gliomas in adult, and MR was correct in 76%-77% of cases for predicting pathologic grading astrocytomas in two tiered system.

  5. Quality assurance grading of conventional equipment at nuclear power station

    International Nuclear Information System (INIS)

    Li Ping; Li Shichang

    2006-01-01

    Equipment QA grading with the systematic and standardized approach will benefit the concerned organizations by effective allocating of limited resources to guarantee the quality of essential equipment. This paper presents a new quality assurance grading system for the convention systems/equipment of nuclear power station, which is operative and at the same time could help the owner to allot resource reasonably through the analysis of the purpose of grading and the experience and lessons of LINGAO Phase I project. (authors)

  6. Tumor grading of adult astrocytic glioma on MR imaging

    International Nuclear Information System (INIS)

    Chang, Kee Hyun; Choi, Choong Gon; Han, Moon Hee; Lee, Seon Kyu; Suh, Jung Ho; Lee, Ho Kyu; Suh, Dae Chul; Choi, Kyu Ho; Byun, Hong Sik; Choi, Woo Suk

    1994-01-01

    The purpose of this study is to determine predictive MR features for grading of astrocytic gliomas and to evaluate the accuracy of MR grading in these tumors. We retrospectively reviewed 135 cases of supratentorial astrocytic gliomas in adult (age > 15 years), all of which were proved by open biopsy. Two observers analysed MR images independently with criteria of margin, edema, mass effect, signal heterogeneity, necrosis, cyst formation, hemorrhage, tumor vascularity, enhancement degree, and enhancement size. The patterns of enhancement were categorized into no, homogeneous, heterogeneous, thin smooth rim, thin irregular rim, and thick irregular rim enhancement patterns. Observers finally diagnosed each case as one of low-grade astrocytoma, anaplastic astrocytoma or glioblastoma multiforme. Statistically significant MR features for grading of these tumors were revealed as necrosis (p < 0.001), edema (0.008), and signal heterogeneity (p < 0.025). When compared with histopathologic grading, MR graded correctly 76%- 77% of cases in two tired system(low-grade astrocytoma versus high-grade astrocytoma), but only 67%-69% of cases in three tiered system(low-grade astrocytoma, anaplastic astrocytoma, glioblastoma multiforme). No contrast enhancement was seen in 45% and 23% of low-grade astrocytoma and anaplastic astrocytoma respectively. Glioblastoma multiforme frequently showed thick irregular rim enhancement (57%), but no enhancement at all in 8%. We have concluded that necrosis and edema are significant predictive MR features for grading of supratentorial astrocytic gliomas in adult, and MR was correct in 76%-77% of cases for predicting pathologic grading astrocytomas in two tiered system

  7. Strategy Guideline: Modeling Enclosure Design in Above-Grade Walls

    Energy Technology Data Exchange (ETDEWEB)

    Lstiburek, J. [Building Science Corporation, Westford, MA (United States); Ueno, K. [Building Science Corporation, Westford, MA (United States); Musunuru, S. [Building Science Corporation, Westford, MA (United States)

    2016-02-24

    The Strategy Guideline describes how to model and interpret results of models for above grade walls. The Measure Guideline analyzes the failure thresholds and criteria for above grade walls. A library of above-grade walls with historically successful performance was used to calibrate WUFI (Warme Und Feuchte Instationar) software models. The information is generalized for application to a broad population of houses within the limits of existing experience.

  8. Preventing halo bias in grading the work of university students

    OpenAIRE

    John M. Malouff; Sarah J. Stein; Lodewicka N. Bothma; Kimberley Coulter; Ashley J. Emmerton

    2014-01-01

    Experts have advocated anonymous marking as a means of minimizing bias in subjective student assessment. In the present study, 159 faculty members or teaching assistants across disciplines were randomly assigned (1) to grade a poor oral presentation of a university student, (2) to grade a good oral presentation of the same student, or (3) not to grade any oral presentation of the student. All graders then assessed the same written work by the student. A linear-contrasts analysis showed that, ...

  9. The 2014 International Society of Urological Pathology (ISUP) Consensus Conference on Gleason Grading of Prostatic Carcinoma: Definition of Grading Patterns and Proposal for a New Grading System.

    Science.gov (United States)

    Epstein, Jonathan I; Egevad, Lars; Amin, Mahul B; Delahunt, Brett; Srigley, John R; Humphrey, Peter A

    2016-02-01

    In November, 2014, 65 prostate cancer pathology experts, along with 17 clinicians including urologists, radiation oncologists, and medical oncologists from 19 different countries gathered in a consensus conference to update the grading of prostate cancer, last revised in 2005. The major conclusions were: (1) Cribriform glands should be assigned a Gleason pattern 4, regardless of morphology; (2) Glomeruloid glands should be assigned a Gleason pattern 4, regardless of morphology; (3) Grading of mucinous carcinoma of the prostate should be based on its underlying growth pattern rather than grading them all as pattern 4; and (4) Intraductal carcinoma of the prostate without invasive carcinoma should not be assigned a Gleason grade and a comment as to its invariable association with aggressive prostate cancer should be made. Regarding morphologies of Gleason patterns, there was clear consensus on: (1) Gleason pattern 4 includes cribriform, fused, and poorly formed glands; (2) The term hypernephromatoid cancer should not be used; (3) For a diagnosis of Gleason pattern 4, it needs to be seen at 10x lens magnification; (4) Occasional/seemingly poorly formed or fused glands between well-formed glands is insufficient for a diagnosis of pattern 4; (5) In cases with borderline morphology between Gleason pattern 3 and pattern 4 and crush artifacts, the lower grade should be favored; (6) Branched glands are allowed in Gleason pattern 3; (7) Small solid cylinders represent Gleason pattern 5; (8) Solid medium to large nests with rosette-like spaces should be considered to represent Gleason pattern 5; and (9) Presence of unequivocal comedonecrosis, even if focal is indicative of Gleason pattern 5. It was recognized by both pathologists and clinicians that despite the above changes, there were deficiencies with the Gleason system. The Gleason grading system ranges from 2 to 10, yet 6 is the lowest score currently assigned. When patients are told that they have a Gleason score 6 out

  10. 2015 Strategic Petroleum Reserve Bayou Choctaw Well Integrity Grading Report.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Barry L; Lord, David; Lord, Anna C. Snider; Bettin, Giorgia; Park, Byoung; Rudeen, D.K.; Eldredge, L.L.; Wynn, K.; Checkai, D.; Osborne, G.; Moore, D.

    2015-10-01

    This report summarizes the work performed in the prioritization of cavern access wells for remediation and monitoring at the Bayou Choctaw Strategic Petroleum Reserve site. The grading included consideration of all 15 wells at the Bayou Choctaw site, with each active well receiving a separate grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The factors and grading framework used here are the same as those used in developing similar well remediation and monitoring priorities at the Big Hill, Bryan Mound, and West Hackberry Strategic Petroleum Reserve Sites.

  11. Grading of direct laryngoscopy. A survey of current practice.

    Science.gov (United States)

    Cohen, A M; Fleming, B G; Wace, J R

    1994-06-01

    One hundred and twenty anaesthetists (30 of each grade), from three separate regions, were interviewed as to how they recorded the appearance of laryngeal structures at direct laryngoscopy and about their knowledge of the commonly used numerical grading system. About two-thirds of anaesthetists surveyed (69.2%) used the numerical grading system, but of these, over half could not identify a 'grade 2' laryngoscopic appearance correctly. Of anaesthetists who did not use the numerical method, over half could not correctly state the difference between a 'grade 2' and a 'grade 3' laryngoscopic appearance. Over 40% of anaesthetists stated incorrectly that the grading should be made on the initial view, even when laryngeal pressure had been needed. Junior anaesthetists were more likely to use the numerical method of recording. The results show that there is unacceptable uncertainty and inaccuracy in the use of the numerical grading system by users as well as non-users, which makes the current routine clinical use of the numerical grading system unsatisfactory.

  12. Will Instructors Save Time Using a Specifications Grading System?

    Directory of Open Access Journals (Sweden)

    Sarah Grace Prescott

    2015-08-01

    Full Text Available Review of: Specifications Grading: Restoring Rigor, Motivating Students, and Saving Faculty Time; Linda Nilson and Claudia J. Stranny; (2014. Stylus Publishing, Sterling, VA. 184 pages.

  13. 2015 Strategic Petroleum Reserve West Hackberry Well Integrity Grading Report.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Barry L; Lord, David; Lord, Anna C. Snider; Bettin, Giorgia; Sobolik, Steven R.; Rudeen, David Keith; Eldredge, Lisa L. (FFPO); Wynn, Karen (FFPO); Checkai, Dean (FFPO); Osborne, Gerad (FFPO); Moore, Darryl (FFPO)

    2015-04-01

    This report summarizes the work performed in the prioritization of cavern access wells for remediation and monitoring at the West Hackberry Strategic Petroleum Reserve site. The grading included consideration of all 31 wells at the West Hackberry site, with each well receiving a separate grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The factors and grading framework used here are the same as those used in developing similar well remediation and monitoring priorities at the Big Hill and Bryan Mound Strategic Petroleum Reserve Sites.

  14. 2014 Strategic Petroleum Reserve Bryan Mound Well Integrity Grading Report.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Barry L; Lord, David; Lord, Anna C. Snider; Bettin, Giorgia; Sobolik, Steven R.; Rudeen, David Keith; Eldredge, Lisa L. (FFPO); Wynn, Karen (FFPO); Checkai, Dean (FFPO); Osborne, Gerad (FFPO); Moore, Darryl (FFPO)

    2015-04-01

    This report summarizes the work performed in the prioritization of cavern access wells for remediation and monitoring at the Bryan Mound Strategic Petroleum Reserve site. The grading included consideration of all 47 wells at the Bryan Mound site, with each well receiving a separate grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The factors and grading framework used here are the same as those used in developing similar well remediation and monitoring priorities at the Big Hill Strategic Petroleum Reserve Site.

  15. Electronic transport behavior of diameter-graded Ag nanowires

    International Nuclear Information System (INIS)

    Wang Xuewei; Yuan Zhihao

    2010-01-01

    Ag nanowires with a graded diameter in anodic aluminum oxide (AAO) membranes were fabricated by the direct-current electrodeposition. The Ag nanowires have a graded-change in diameter from 8 to 32 nm, which is matched with the graded-change of the AAO pore diameter. Electronic transport measurements show that there is a transport behavior similar to that of a metal-semiconductor junction along the axial direction in the diameter-graded Ag nanowires. Such a novel homogeneous nanojunction will be of great fundamental and practical significance.

  16. Electronic transport behavior of diameter-graded Ag nanowires

    Science.gov (United States)

    Wang, Xue Wei; Yuan, Zhi Hao

    2010-05-01

    Ag nanowires with a graded diameter in anodic aluminum oxide (AAO) membranes were fabricated by the direct-current electrodeposition. The Ag nanowires have a graded-change in diameter from 8 to 32 nm, which is matched with the graded-change of the AAO pore diameter. Electronic transport measurements show that there is a transport behavior similar to that of a metal-semiconductor junction along the axial direction in the diameter-graded Ag nanowires. Such a novel homogeneous nanojunction will be of great fundamental and practical significance.

  17. Setting standards to determine core clerkship grades in pediatrics.

    Science.gov (United States)

    Dudas, Robert A; Barone, Michael A

    2014-01-01

    One of the greatest challenges for clerkship directors is assigning a final grade and determining the precise point at which a student either passes or fails a clinical clerkship. The process of incorporating both subjective and objective assessment data to provide a final summative grade can be challenging. We describe our experience conducting a standard-setting exercise to set defensible cut points in a 4-tiered grading system in our pediatric clerkship. Using the Hofstee standard-setting approach, 8 faculty members participated in an exercise to establish grade cut points. These faculty members were subsequently surveyed to assess their attitudes toward the standard-setting process as well as their reactions to these newly proposed standards. We applied the new cut points to a historic cohort of 116 Johns Hopkins University School of Medicine students from the academic year 2012-2013 to assess the potential impact on grade distributions. The resultant grading schema would lead to a significant increase in the number of students receiving a failing grade and a decrease in the number of students receiving a grade of honors in a historical cohort. Faculty reported that the Hofstee method was easy to understand and fair. All faculty members thought that grade inflation presently exists within the pediatric clerkship. This study demonstrates that practical standards using the Hofstee method can be set for medical students in a pediatric clerkship in which multiple performance measures are used. Copyright © 2014 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

  18. Cut-off Grade Optimization for Maximizing the Output Rate

    Directory of Open Access Journals (Sweden)

    A. Khodayari

    2012-12-01

    Full Text Available In the open-pit mining, one of the first decisions that must be made in production planning stage, after completing the design of final pit limits, is determining of the processing plant cut-off grade. Since this grade has an essential effect on operations, choosing the optimum cut-off grade is of considerable importance. Different goals may be used for determining optimum cut-off grade. One of these goals may be maximizing the output rate (amount of product per year, which is very important, especially from marketing and market share points of view. Objective of this research is determining the optimum cut-off grade of processing plant in order to maximize output rate. For performing this optimization, an Operations Research (OR model has been developed. The object function of this model is output rate that must be maximized. This model has two operational constraints namely mining and processing restrictions. For solving the model a heuristic method has been developed. Results of research show that the optimum cut-off grade for satisfying pre-stated goal is the balancing grade of mining and processing operations, and maximum production rate is a function of the maximum capacity of processing plant and average grade of ore that according to the above optimum cut-off grade must be sent to the plant.

  19. Advanced soft computing diagnosis method for tumour grading.

    Science.gov (United States)

    Papageorgiou, E I; Spyridonos, P P; Stylios, C D; Ravazoula, P; Groumpos, P P; Nikiforidis, G N

    2006-01-01

    To develop an advanced diagnostic method for urinary bladder tumour grading. A novel soft computing modelling methodology based on the augmentation of fuzzy cognitive maps (FCMs) with the unsupervised active Hebbian learning (AHL) algorithm is applied. One hundred and twenty-eight cases of urinary bladder cancer were retrieved from the archives of the Department of Histopathology, University Hospital of Patras, Greece. All tumours had been characterized according to the classical World Health Organization (WHO) grading system. To design the FCM model for tumour grading, three experts histopathologists defined the main histopathological features (concepts) and their impact on grade characterization. The resulted FCM model consisted of nine concepts. Eight concepts represented the main histopathological features for tumour grading. The ninth concept represented the tumour grade. To increase the classification ability of the FCM model, the AHL algorithm was applied to adjust the weights of the FCM. The proposed FCM grading model achieved a classification accuracy of 72.5%, 74.42% and 95.55% for tumours of grades I, II and III, respectively. An advanced computerized method to support tumour grade diagnosis decision was proposed and developed. The novelty of the method is based on employing the soft computing method of FCMs to represent specialized knowledge on histopathology and on augmenting FCMs ability using an unsupervised learning algorithm, the AHL. The proposed method performs with reasonably high accuracy compared to other existing methods and at the same time meets the physicians' requirements for transparency and explicability.

  20. Otological and vestibular symptoms in patients with low grade (Quebec grades one and two) whiplash injury.

    Science.gov (United States)

    Rowlands, R G; Campbell, I K; Kenyon, G S

    2009-02-01

    To establish the prevalence of new vestibular and otological symptoms in a group of patients who had sustained a low grade (Quebec grades one or two) whiplash injury. A retrospective review of the case records of 109 patients undergoing assessment by a single practitioner for the purposes of compiling a medicolegal report on their whiplash injury. Four patients complained of short-lived, non-specific dizziness symptoms in the acute phase following their original injury. There were no reports of vertigo, tinnitus or hearing loss after a mean period of 149 days following the whiplash injury. No patients reported otological or persistent vestibular symptoms in the acute phase following their whiplash injury. This suggests that caution should be exercised when attributing these symptoms to such an injury. Before whiplash injuries are admitted as an aetiological factor in the development of such symptoms, other causes should be excluded.

  1. Grade III or Grade IV Hypertensive Retinopathy with Severely Elevated Blood Pressure

    Directory of Open Access Journals (Sweden)

    Amanda D Henderson

    2012-12-01

    Full Text Available Introduction: Hypertensive retinopathy describes a spectrum of retinal changes in patients with elevated blood pressure (BP. It is unknown why some patients are more likely to develop acute ocular end-organ damage than others with similar BP. We examined risk factors for grade III/IV hypertensive retinopathy among patients with hypertensive urgency in the emergency department (ED and compared healthcare utilization and mortality between patients with and without grade III/IV hypertensive retinopathy.Methods: A preplanned subanalysis of patients who presented to a university hospital ED with diastolic BP > 120 mmHg and who enrolled in the Fundus Photography versus Ophthalmoscopy Trial Outcomes in the ED study was performed. Bilateral nonmydriatic ocular fundus photographs, vital signs, and demographics were obtained at presentation. Past medical history, laboratory values, healthcare utilization, and mortality were ascertained from medical record review at least 8 months after initial ED visit.Results: Twenty-one patients with diastolic BP > 120 mmHg, 7 of whom (33% had grade III/IV hypertensive retinopathy, were included. Patients with retinopathy were significantly younger than those without (median 33 vs 50 years, P = 0.02. Mean arterial pressure (165 vs 163 mmHg was essentially equal in the 2 groups. Patients with retinopathy had substantially increased but nonsignificant rates of ED revisit (57% vs 29%, P = 0.35 and hospital admission after ED discharge (43% vs 14%, P = 0.28. One of the patients with retinopathy died, but none without.Conclusion: Younger patients may be at higher risk for grade III/IV hypertensive retinopathy among patients with hypertensive urgency. Chronic compensatory mechanisms may have not yet developed in these younger patients. Alternatively, older patients with retinopathy may be underrepresented secondary to increased mortality among these patients at a younger age (survivorship bias. Further research is needed to

  2. RELATIONSHIP BETWEEN ESOPHAGITIS GRADES AND HELICOBACTER PYLORI.

    Science.gov (United States)

    Ribeiro, Patrícia Fernanda Saboya; Kubrusly, Luiz Fernandao; Nassif, Paulo Afonso Nunes; Ribeiro, Irma Cláudia Saboya; Bertoldi, Andressa de Souza; Batistão, Venessa Caroline

    2016-01-01

    The Helicobacter pylori infection (HP) is related to the development of gastric lesions and lymphoma; however, it is not known if there is a relation with gastroesophageal reflux disease and reflux esophagitis. To evaluate HP's relationship with esophagitis in patients undergoing upper endoscopy. Observational, retrospective and cross-sectional study, being evaluated 9576 patients undergoing outpatient endoscopic examination during the period between January and December 2015. Were included patients with any esophageal alteration at the examination; greater than 18; of both genders; independent of the complaint or the reason for the examination, illness or drug use. Were excluded those with active bleeding during the examination and in use of anticoagulants. The variables gender, age, esophagitis and result of the urease test, were studied. For statistical analysis was used the Epi Info software 7.1.5.2. Most of the samples consisted of women and the overall average age was 46.54±16.32 years. The presence of infection was balanced for gender: 1204 (12.56%) women and 952 (13.92%) men. Relating degree of esophagitis HP- and HP+ was observed that the type A was the most common (58.79%, n=1460); 604 (24.32%) had grade B; 334 (13.45%) grade C, and 85 (3.42%) grade D. In the relation between the grade of esophagitis with gender, esophagitis A was predominant in women and present in 929 (63.33%), followed by type B, 282 (46.68%), 136 C (40.71%) and D 30 (35.29%). In men 531 (36.36%) showed type A, 322 (53.31%) B, 198 (59.28%) C, and 55 (64.70%) D. Among the groups 40-50 and over 60 years there was a significant difference in whether have or not have HP+. There is no significant difference between HP infection and the different grades of esophagitis. A infecção pelo Helicobacter pylori (HP) é relacionada com o desenvolvimento de lesões e linfoma gástricos; porém, ainda não se sabe ao certo se há relação dele com a doença do refluxo gastroesofágico e esofagite

  3. Analysis of DTI-Derived Tensor Metrics in Differential Diagnosis between Low-grade and High-grade Gliomas.

    Science.gov (United States)

    Jiang, Liang; Xiao, Chao-Yong; Xu, Quan; Sun, Jun; Chen, Huiyou; Chen, Yu-Chen; Yin, Xindao

    2017-01-01

    Purpose: It is critical and difficult to accurately discriminate between high- and low-grade gliomas preoperatively. This study aimed to ascertain the role of several scalar measures in distinguishing high-grade from low-grade gliomas, especially the axial diffusivity (AD), radial diffusivity (RD), planar tensor (Cp), spherical tensor (Cs), and linear tensor (Cl) derived from diffusion tensor imaging (DTI). Materials and Methods: Fifty-three patients with pathologically confirmed brain gliomas (21 low-grade and 32 high-grade) were included. Contrast-enhanced T1-weighted images and DTI were performed in all patients. The AD, RD, Cp, Cs, and Cl values in the tumor zone, peritumoral edema zone, white matter (WM) adjacent to edema and contralateral normal-appearing white matter (NAWM) were calculated. The DTI parameters and tumor grades were statistically analyzed, and receiver operating characteristic (ROC) curve analysis was also performed. Results: The DTI metrics in the affected hemisphere showed significant differences from those in the NAWM, except for the AD values in the tumor zone and the RD values in WM adjacent to edema in the low-grade groups, as well as the Cp values in WM adjacent to edema in the high-grade groups. AD in the tumor zone as well as Cs and Cl in WM adjacent to edema revealed significant differences between the low- and high-grade gliomas. The areas under the curve (Az) of all three metrics were greater than 0.5 in distinguishing low-grade from high-grade gliomas by ROC curve analysis, and the best DTI metric was Cs in WM adjacent to edema (Az: 0.692). Conclusion: AD in the tumor zone as well as Cs and Cl in WM adjacent to edema will provide additional information to better classify gliomas and can be used as non-invasive reliable biomarkers in glioma grading.

  4. SURFACE TREATMENT AND EXAMINATION OF GRADE 2 AND GRADE 5 TITANIUM

    Directory of Open Access Journals (Sweden)

    Peter Nagy

    2016-02-01

    Full Text Available Surface characteristics play an important role in the implant-bone integration that is required for the long-term reliability of dental and orthopedic implants. In this paper, we investigate the effect of acid etching on the mass reduction and roughness of grade 2 and grade 5 Ti under controlled experimental conditions. Three different etching compounds were investigated: 30% HCl, 85% H3PO4 and the compound of 30% (COOH2 × 2H2O and 30% H2O2 in various treatment intervals under controlled temperature. Stereo microscopy, scanning electron microscopy, roughness and weight measurements were carried out on the samples. We found that neither 85% H3PO4 nor the compound of 30% (COOH2 × 2H2O and 30% H2O2 were able to remove the machining marks from the surface of Ti discs in our experimental setting. On the other hand, etching in 30% HCl yielded even surfaces both on Ti grade 2 and 5 discs. We also found that etching at higher temperatures in 30% HCl resulted in significant mass loss.

  5. Structural trends in off stoichiometric chalcopyrite type compound semiconductors

    International Nuclear Information System (INIS)

    Stephan, Christiane

    2011-01-01

    Energy supply is one of the most controversial topics that are currently discussed in our global community. Most of the energy delivered to the customer today has its origin in fossil and nuclear power plants. Indefinable risks and the radioactive waste repository problem of the latter as well as the global scarcity of fossil resources cause the renewable energies to grow more and more important for achieving sustainability. The main renewable energy sources are wind power, hydroelectric power and solar energy. On the photovoltaic (PV) market different materials are competing as part of different kinds of technologies, with the largest contribution still coming from wafer based crystalline silicon solar cells (95 %). Until now thin film solar cells only contribute a small portion to the whole PV market, but large capacities are under construction. Thin film photovoltaic shows a number of advantages in comparison to wafer based crystalline silicon PV. Among these material usage and production cost reduction are two prominent examples. The type of PV materials, which are analyzed in this work, are high potential compounds that are widely used as absorber layer in thin film solar cells. These are compound semiconductors of the type CuB III C VI 2 (B III = In, Ga and C VI = Se, S). Several years of research have already gone into understanding the efficiency limiting factors for solar cell devices fabricated from this compound. Most of the studies concerning electronic defects are done by spectroscopic methods mostly performed using thin films from different kinds of synthesis, without any real knowledge regarding the structural origin of these defects. This work shows a systematic fundamental structural study of intrinsic point defects that are present within the material at various compositions in CuB III C VI 2 compound semiconductors. The study is done on reference powder samples with well determined chemical composition and using advanced diffraction techniques, such as neutron and synchrotron X-ray diffraction. The results show that the main existing defects are found to be copper vacancies and B III Cu anti-site defects. Type and concentrations vary with the composition. It is demonstrated that, when assuming spontaneous formation of electrically neutral defect complexes made of these isolated point defects, the density of cationic point defects is reduced by an order of magnitude. This explains why the existence of native cationic point defects may not be the main efficiency limiting factor in thin film solar cells built with a CuB III C VI 2 absorber. This pinpoints why the mere presence of native cationic point defects does probably not suffice as main efficiency limiting factor in thin film solar cells based on CuB III C VI 2 -type absorbers.

  6. Development of Chalcopyrite Crystals for Nonlinear Optical Applications

    Science.gov (United States)

    1974-12-01

    write the expansion ol the homopolar and the heteropolar part of the mean energy gap in the following way. £.(«) - £. + (a«», + (a.)’*, + (Ha) C...a nearly linear relation over a wide 7 —12-um spectral range. We therefore used a 1 stepping motor and synchronously rotated the AgGaSe, crystal

  7. Structural trends in off stoichiometric chalcopyrite type compound semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Stephan, Christiane

    2011-03-15

    Energy supply is one of the most controversial topics that are currently discussed in our global community. Most of the energy delivered to the customer today has its origin in fossil and nuclear power plants. Indefinable risks and the radioactive waste repository problem of the latter as well as the global scarcity of fossil resources cause the renewable energies to grow more and more important for achieving sustainability. The main renewable energy sources are wind power, hydroelectric power and solar energy. On the photovoltaic (PV) market different materials are competing as part of different kinds of technologies, with the largest contribution still coming from wafer based crystalline silicon solar cells (95 %). Until now thin film solar cells only contribute a small portion to the whole PV market, but large capacities are under construction. Thin film photovoltaic shows a number of advantages in comparison to wafer based crystalline silicon PV. Among these material usage and production cost reduction are two prominent examples. The type of PV materials, which are analyzed in this work, are high potential compounds that are widely used as absorber layer in thin film solar cells. These are compound semiconductors of the type CuB{sup III}C{sup VI}{sub 2} (B{sup III} = In, Ga and C{sup VI} = Se, S). Several years of research have already gone into understanding the efficiency limiting factors for solar cell devices fabricated from this compound. Most of the studies concerning electronic defects are done by spectroscopic methods mostly performed using thin films from different kinds of synthesis, without any real knowledge regarding the structural origin of these defects. This work shows a systematic fundamental structural study of intrinsic point defects that are present within the material at various compositions in CuB{sup III}C{sup VI}{sub 2} compound semiconductors. The study is done on reference powder samples with well determined chemical composition and using advanced diffraction techniques, such as neutron and synchrotron X-ray diffraction. The results show that the main existing defects are found to be copper vacancies and B{sup III}{sub Cu} anti-site defects. Type and concentrations vary with the composition. It is demonstrated that, when assuming spontaneous formation of electrically neutral defect complexes made of these isolated point defects, the density of cationic point defects is reduced by an order of magnitude. This explains why the existence of native cationic point defects may not be the main efficiency limiting factor in thin film solar cells built with a CuB{sup III}C{sup VI}{sub 2} absorber. This pinpoints why the mere presence of native cationic point defects does probably not suffice as main efficiency limiting factor in thin film solar cells based on CuB{sup III}C{sup VI}{sub 2}-type absorbers.

  8. Schottky contact analysis of photovoltaic chalcopyrite thin film absorbers

    International Nuclear Information System (INIS)

    Schlenker, E.; Mertens, V.; Parisi, J.; Reineke-Koch, R.; Koentges, M.

    2007-01-01

    Current-voltage and capacitance-voltage measurements serve to analyze thermally evaporated Al Schottky contacts on Cu(In, Ga)Se 2 based photovoltaic thin film devices, either taken as grown or etched in a bromine-methanol solution. The characteristics of the Schottky contacts on the as-grown films give evidence for some dielectric layer developing between the metal and the semiconductor. Etching the semiconductor surface prior to evaporation of the Al front contact yields a pure metal-semiconductor behavior, including effects that can be attributed to an additional diode at the Mo contact. Simulations confirm the experimental results

  9. Desulfurization of chalcopyrite and molybdenite by atomic hydrogen

    International Nuclear Information System (INIS)

    Bagdasaryan, V.R.; Kosoyan, A.Zh.; Niazyan, O.M.

    1989-01-01

    Molybdenite (MoS 2 ) desulfurization by monatomic hydrogen in 625-800 K range was studied using helium as diluent gas. Desulfurization degree at 680 K equals 9%. Temperature growth elevates sulfur content in molybdenite. The effect of initial molybdenite enrichment with temperature growth up to 800 K is probably caused by removal of reduced molybdenum capable to form oxide in the presence of traces of oxygen contained in inert diluent gas

  10. Disposal of Surplus Weapons Grade Plutonium

    International Nuclear Information System (INIS)

    Alsaed, H.; Gottlieb, P.

    2000-01-01

    The Office of Fissile Materials Disposition is responsible for disposing of inventories of surplus US weapons-usable plutonium and highly enriched uranium as well as providing, technical support for, and ultimate implementation of, efforts to obtain reciprocal disposition of surplus Russian plutonium. On January 4, 2000, the Department of Energy issued a Record of Decision to dispose of up to 50 metric tons of surplus weapons-grade plutonium using two methods. Up to 17 metric tons of surplus plutonium will be immobilized in a ceramic form, placed in cans and embedded in large canisters containing high-level vitrified waste for ultimate disposal in a geologic repository. Approximately 33 metric tons of surplus plutonium will be used to fabricate MOX fuel (mixed oxide fuel, having less than 5% plutonium-239 as the primary fissile material in a uranium-235 carrier matrix). The MOX fuel will be used to produce electricity in existing domestic commercial nuclear reactors. This paper reports the major waste-package-related, long-term disposal impacts of the two waste forms that would be used to accomplish this mission. Particular emphasis is placed on the possibility of criticality. These results are taken from a summary report published earlier this year

  11. Magnetothermoelastic creep analysis of functionally graded cylinders

    International Nuclear Information System (INIS)

    Loghman, A.; Ghorbanpour Arani, A.; Amir, S.; Vajedi, A.

    2010-01-01

    This paper describes time-dependent creep stress redistribution analysis of a thick-walled FGM cylinder placed in uniform magnetic and temperature fields and subjected to an internal pressure. The material creep, magnetic and mechanical properties through the radial graded direction are assumed to obey the simple power law variation. Total strains are assumed to be the sum of elastic, thermal and creep strains. Creep strains are time, temperature and stress dependent. Using equations of equilibrium, stress-strain and strain-displacement a differential equation, containing creep strains, for displacement is obtained. Ignoring creep strains in this differential equation a closed form solution for the displacement and initial magnetothermoelastic stresses at zero time is presented. Initial magnetothermoelastic stresses are illustrated for different material properties. Using Prandtl-Reuss relation in conjunction with the above differential equation and the Norton's law for the material uniaxial creep constitutive model, the radial displacement rate is obtained and then the radial and circumferential creep stress rates are calculated. Creep stress rates are plotted against dimensionless radius for different material properties. Using creep stress rates, stress redistributions are calculated iteratively using magnetothermoelastic stresses as initial values for stress redistributions. It has been found that radial stress redistributions are not significant for different material properties, however major redistributions occur for circumferential and effective stresses.

  12. Cost effective nuclear commercial grade dedication

    International Nuclear Information System (INIS)

    Maletz, J.J.; Marston, M.J.

    1991-01-01

    This paper describes a new computerized database method to create/edit/view specification technical data sheets (mini-specifications) for procurement of spare parts for nuclear facility maintenance and to develop information that could support possible future facility life extension efforts. This method may reduce cost when compared with current manual methods. The use of standardized technical data sheets (mini-specifications) for items of the same category improves efficiency. This method can be used for a variety of tasks, including: Nuclear safety-related procurement; Non-safety related procurement; Commercial grade item procurement/dedication; Evaluation of replacement items. This program will assist the nuclear facility in upgrading its procurement activities consistent with the recent NUMARC Procurement Initiative. Proper utilization of the program will assist the user in assuring that the procured items are correct for the applications, provide data to assist in detecting fraudulent materials, minimize human error in withdrawing database information, improve data retrievability, improve traceability, and reduce long-term procurement costs

  13. Selective Oxidation of Soft Grade Carbon

    Directory of Open Access Journals (Sweden)

    Zecevic, N.

    2007-12-01

    Full Text Available Oil-furnace carbon black is produced by pyrolysis of gaseous or liquid hydrocarbons or their mixtures. The oil feedstock for the production of oil-furnace carbon black is mainly composed of high-boiling aromatic hydrocarbons, which are residues of petroleum cracking, while the gaseous raw material is commonly natural gas. Most of the oil-furnace carbon black production (> 99 % is used as a reinforcing agent in rubber compounds. Occasionally, oil-furnace carbon blacks are used in contact with other rubber compounds and fillers that have different pigments, particularly with the color white. It has been observed that frequently a migrating rubber soluble colorant would enter the white or light colored rubber composition from the adjacent carbon black filled rubber, resulting in a highly undesirable staining effect. Methods for determining non-oxidized residue on the surface of the oil-furnace carbon black include extraction of carbon black with the appropriate organic solvent, and measuring the color of the organic solvent by means of a colorimeter on 425 nm (ASTM D 1618-99. Transmittance values of 85 % or more are indicative of a practically non-staining carbon black, while transmittance values below 50 % generally lead to a carbon black with pronounced staining characteristics. Many oil-furnace carbon blacks, particularly those with a larger particle size (dp > 50 nm which are produced by pyrolysis, have strongly adsorbed non-reacted oil on their surfaces. Upon incorporation in a rubber compound, the colored materials are gradually dissolved by the rubber matrix and migrate freely into adjacent light colored rubber compounds, causing a highly objectionable staining effect. Adjusting furnace parameters in the industrial process of producing specific soft grades of carbon black cannot obtain minimal values of toluene discoloration. The minimal value of toluene discoloration is very important in special applications. Therefore, after-treatment of

  14. Prognostic implications of 2005 Gleason grade modification

    DEFF Research Database (Denmark)

    Thomsen, Frederik Birkebæk; Folkvaljon, Yasin; Brasso, Klaus

    2016-01-01

    ,890 men assessed with the modified Gleason classification, diagnosed between 2003 and 2007, underwent primary RP. Histopathology was reported according to the Gleason Grading Groups (GGG): GGG1 = Gleason score (GS) 6, GGG2 = GS 7(3 + 4), GGG3 = GS 7(4 + 3), GGG4 = GS 8 and GGG5 = GS 9-10. Cumulative...... incidence and multivariable Cox proportional hazards regression models were used to assess difference in BCR. RESULTS: The cumulative incidence of BCR was lower using the modified compared to the original classification: GGG2 (16% vs. 23%), GGG3 (21% vs. 35%) and GGG4 (18% vs. 34%), respectively. Risk......OBJECTIVE: To assess the impact of the 2005 modification of the Gleason classification on risk of biochemical recurrence (BCR) after radical prostatectomy (RP). PATIENTS AND METHODS: In the Prostate Cancer data Base Sweden (PCBaSe), 2,574 men assessed with the original Gleason classification and 1...

  15. Chemical and microstructural diversity of steel grades

    Directory of Open Access Journals (Sweden)

    Zorc, B.

    2002-12-01

    Full Text Available The aim of the paper is to show, using theoretical and practical analyses, chemical and microstructural differences among individual types of steel grades 355 found in the market. The mechanical properties required for these steels are achieved by alloying or thermomechanical treatment. It was found that the individual types of this steel are poorly weldable, particularly those of large thickness.

    El objetivo del artículo es presentar, en base a un análisis teórico y práctico, las diferencias químicas y microestructurales entre los diferentes tipos de aceros calidad 355 que pueden encontrarse en el mercado. Las características mecánicas requeridas en estos aceros se consiguen con aleaciones, o bien a través de tratamientos termo-mecánicos.Se ha llegado a la conclusión de que determinados tipos de acero son más difíciles de soldar, en especial cuando se trata de espesores grandes.

  16. Predicting Second Grade Listening Comprehension Using Prekindergarten Measures

    Science.gov (United States)

    Alonzo, Crystle N.; Yeomans-Maldonado, Gloria; Murphy, Kimberly A.; Bevens, Beau

    2016-01-01

    Purpose: The purpose of this study was to determine prekindergarten predictors of listening comprehension in second grade. Methods: Within a large, 5-year longitudinal study, children progressing from prekindergarten to second grade were administered a comprehensive set of prekindergarten measures of foundational language skills (vocabulary and…

  17. 76 FR 5120 - Highway-Rail Grade Crossing; Safe Clearance

    Science.gov (United States)

    2011-01-28

    ... suggested that FMCSA should provide pavement markings and signage at or near grade crossings to indicate the... eligible for funding under 23 U.S.C. 130; (2) improvement of highway signage and pavement markings; and (3... crossings might get pavement markings and signage and that not all grade-crossing improvements are likely to...

  18. The Effectiveness of Tutoring on Developmental English Grades

    Science.gov (United States)

    Vick, Nicholas; Robles-Piña, Rebecca A.; Martirosyan, Nara M.; Kite, Valerie

    2015-01-01

    Tutoring is an important form of academic support for developmental education students. A comparison study was conducted to investigate the benefits of tutoring on the final grades for developmental English students who participated in tutoring versus those students who did not. The final grades for three consecutive semesters were analyzed to…

  19. Student Test Grades in College: A Study of Possible Predictors

    Science.gov (United States)

    Hammonds, Frank; Mariano, Gina

    2015-01-01

    Research on variables related to test performance has produced mixed results. Typically, research of this type involves only a few variables. In an attempt to obtain a more complete picture, we investigated how test grades might be related to variables such as classification, student seating location, test completion time, predicted grade, time…

  20. Grades, Gender, and Encouragement: A Regression Discontinuity Analysis

    Science.gov (United States)

    Owen, Ann L.

    2010-01-01

    The author employs a regression discontinuity design to provide direct evidence on the effects of grades earned in economics principles classes on the decision to major in economics and finds a differential effect for male and female students. Specifically, for female students, receiving an A for a final grade in the first economics class is…

  1. Important Text Characteristics for Early-Grades Text Complexity

    Science.gov (United States)

    Fitzgerald, Jill; Elmore, Jeff; Koons, Heather; Hiebert, Elfrieda H.; Bowen, Kimberly; Sanford-Moore, Eleanor E.; Stenner, A. Jackson

    2015-01-01

    The Common Core set a standard for all children to read increasingly complex texts throughout schooling. The purpose of the present study was to explore text characteristics specifically in relation to early-grades text complexity. Three hundred fifty primary-grades texts were selected and digitized. Twenty-two text characteristics were identified…

  2. Do Gender and Physical Attractiveness Affect College Grades?

    Science.gov (United States)

    Krawczyk, Michal

    2018-01-01

    In this study, data on grades awarded for bachelor and master theses at a large Polish university were used to identify possible discrimination on gender or physical attractiveness. The focus is on the gap between the grades awarded by the advisor (who knows the student personally) and the referee (who typically does not, so that gender is less…

  3. Ninth Grade Students' Understanding of The Nature of Scientific Knowledge

    Science.gov (United States)

    Kilic, Kerem; Sungur, Semra; Cakiroglu, Jale; Tekkaya, Ceren

    2005-01-01

    The purpose of this study was to investigate the 9th-grade students' understandings of the nature of scientific knowledge. The study also aimed to investigate the differences in students' understanding of the nature of scientific knowledge by gender, and school types. A total of 575 ninth grade students from four different school types (General…

  4. The Changing Landscape of Grading Systems in US Higher Education

    Science.gov (United States)

    Kleinman, Steven B.; Leidman, Mary Beth; Longcore, Andrew J.

    2018-01-01

    The following study explores the landscape of grading systems utilised in higher education, focusing on the frequency of different types of assessment scales (including Straight Letter, Plus/Minus, and other alternative policies). Although numerous studies have explored the relationship between university grading system and student behaviour,…

  5. Hong's grading for evaluating anterior chamber angle width.

    Science.gov (United States)

    Kim, Seok Hwan; Kang, Ja Heon; Park, Ki Ho; Hong, Chul

    2012-11-01

    To compare Hong's grading method with anterior segment optical coherence tomography (AS-OCT), gonioscopy, and the dark-room prone-position test (DRPT) for evaluating anterior chamber width. The anterior chamber angle was graded using Hong's grading method, and Hong's angle width was calculated from the arctangent of Hong's grades. The correlation between Hong's angle width and AS-OCT parameters was analyzed. The area under the receiver operating characteristic curve (AUC) for Hong's grading method when discriminating between narrow and open angles as determined by gonioscopy was calculated. Correlation analysis was performed between Hong's angle width and intraocular pressure (IOP) changes determined by DRPT. A total of 60 subjects were enrolled. Of these subjects, 53.5 % had a narrow angle. Hong's angle width correlated significantly with the AS-OCT parameters (r = 0.562-0.719, P < 0.01). A Bland-Altman plot showed relatively good agreement between Hong's angle width and the angle width obtained by AS-OCT. The ability of Hong's grading method to discriminate between open and narrow angles was good (AUC = 0.868, 95 % CI 0.756-0.942). A significant linear correlation was found between Hong's angle width and IOP change determined by DRPT (r = -0.761, P < 0.01). Hong's grading method is useful for detecting narrow angles. Hong's grading correlated well with AS-OCT parameters and DRPT.

  6. 78 FR 66655 - Consumer Information; Uniform Tire Quality Grading Standards

    Science.gov (United States)

    2013-11-06

    ... information indicating the relative performance of passenger car tires in the areas of treadwear, traction... [Docket No. NHTSA-2013-0120] RIN 2127-AL49 Consumer Information; Uniform Tire Quality Grading Standards...). ACTION: Interim final rule; request for comments. SUMMARY: The Uniform Tire Quality Grading Standards...

  7. Science Teaching Methods Preferred by Grade 9 Students in Finland

    Science.gov (United States)

    Juuti, Kalle; Lavonen, Jari; Uitto, Anna; Byman, Reijo; Meisalo, Veijo

    2010-01-01

    Students find science relevant to society, but they do not find school science interesting. This survey study analyzes Finnish grade 9 students' actual experiences with science teaching methods and their preferences for how they would like to study science. The survey data were collected from 3,626 grade 9 students (1,772 girls and 1,832 boys)…

  8. Correcting Grade Deflation Caused by Multiple-Choice Scoring.

    Science.gov (United States)

    Baranchik, Alvin; Cherkas, Barry

    2000-01-01

    Presents a study involving three sections of pre-calculus (n=181) at four-year college where partial credit scoring on multiple-choice questions was examined over an entire semester. Indicates that grades determined by partial credit scoring seemed more reflective of both the quantity and quality of student knowledge than grades determined by…

  9. What Did You Get? A Faculty Grade Comparison

    Science.gov (United States)

    Cavanaugh, Joseph K.

    2006-01-01

    Purpose: This study investigates how the increased use of part-time and nontenure-track instructors may result in grade inflation. Design/methodology/approach: This research uses ten years of registrar data at a Midwest State (USA) institution to perform a multiple regression grade analysis. Findings: Evidence is found that part-time and…

  10. Variables associated with Grade R English Additional Language ...

    African Journals Online (AJOL)

    reviewer 1

    Since Grade R is the foundation for formal Grade 1 learning, research conducted ... There appears to be a paucity of research on variables relating to EAL acquisition in South Africa. In a ...... teacher can code switch and explain the meaning of.

  11. Comparison of educational facilitation approaches for Grade R ...

    African Journals Online (AJOL)

    The Early Childhood Development Manager in Mpumalanga is faced with the problem of providing evidence-based guidance of the best facilitation approach in the Grade R context. An investigation on the effect of facilitation, i.e. play-based or formal instruction, on Grade R performance scores in English Additional ...

  12. Reliability Analysis for Safety Grade PLC(POSAFE-Q)

    International Nuclear Information System (INIS)

    Choi, Kyung Chul; Song, Seung Whan; Park, Gang Min; Hwang, Sung Jae

    2012-01-01

    Safety Grade PLC(Programmable Logic Controller), POSAFE-Q, was developed recently in accordance with nuclear regulatory and requirements. In this paper, describe reliability analysis for digital safety grade PLC (especially POSAFE-Q). Reliability analysis scope is Prediction, Calculation of MTBF (Mean Time Between Failure), FMEA (Failure Mode Effect Analysis), PFD (Probability of Failure on Demand). (author)

  13. Typing and grading of cytological category C5 breast lesions

    International Nuclear Information System (INIS)

    Zafar, N.; Jamal, S.; Mamoon, N.; Luqman, M.; Anwar, M.

    2005-01-01

    Objective: To determine the tumour type, cytological grade and nuclear grade on fine-needle aspiration smears in cytological category C5 breast lesions and compare them with histopathological findings. Subjects and Methods: Out of all patients referred to AFIP, Rawalpindi for fine-needle aspiration of breast masses, those adjudged C5 (malignant) were chosen for this study. History, clinical details and mammographic findings were noted. Aspirated smears were examined and an attempt was made to ascertain tumour type, cytological grade and nuclear grade. On excision of these lesions, the cytological findings were compared with those on paraffin-embedded histological sections. Results: A total of 71 patients were included in this study. Of these, 64 (90.14%) were cytologically diagnosed as ductal carcinoma, 4 (5.63%) lobular carcinoma, 2 (2.82%) mucinous carcinoma and 1 (1.41%) as medullary carcinoma. Seventy (98.60%) tumours were correctly typed on aspiration smears. Sixty-eight (95.77%) cases were cytologically graded with accuracy. Nuclear grading was even better on cytology and, excluding one malignant lymphoma, all 70 (100%) smears were assessed correctly. Conclusion: Overall efficiency of the tumour typing, cytological grading and nuclear grading on aspirated material turned out to be quite accurate. In expert hands, cytological examination can be of great help in pre-operative planning and in cases where tumour morphology in paraffin-embedded material has been distorted by neo-adjuvant therapy prior to excision. (author)

  14. Cognitive Dissonance or Revenge? Student Grades and Course Evaluations

    Science.gov (United States)

    Maurer, Trent W.

    2006-01-01

    I tested 2 competing theories to explain the connection between students' expected grades and ratings of instructors: cognitive dissonance and revenge. Cognitive dissonance theory holds that students who expect poor grades rate instructors poorly to minimize ego threat whereas the revenge theory holds that students rate instructors poorly in an…

  15. Wave-function reconstruction in a graded semiconductor superlattice

    DEFF Research Database (Denmark)

    Lyssenko, V. G.; Hvam, Jørn Märcher; Meinhold, D.

    2004-01-01

    We reconstruct a test wave function in a strongly coupled, graded well-width superlattice by resolving the spatial extension of the interband polarisation and deducing the wave function employing non-linear optical spectroscopy. The graded gap superlattice allows us to precisely control the dista...

  16. A CURRICULUM FOR ENGLISH, TEACHER PACKET, GRADE 9.

    Science.gov (United States)

    Nebraska Univ., Lincoln. Curriculum Development Center.

    THE NEBRASKA ENGLISH CURRICULUM FOR GRADE NINE FOCUSES ON THE CONCEPT OF GENRE AND ACCOMPANYING LITERARY ATTITUDES AND DEVICES. SATIRE, COMEDY, AND THE EPIC ARE THE SUBJECTS OF THE LITERARY PROGRAM. LANGUAGE AND COMPOSITION STUDIES, BUILDING UPON EIGHTH-GRADE LANGUAGE HISTORY AND SYNTAX UNITS, CENTER ON GEOGRAPHIC AND SOCIAL DIALECTS, PHONOLOGY,…

  17. Seventh Grade Students' Conceptions of Global Warming and Climate Change

    Science.gov (United States)

    Shepardson, Daniel P.; Niyogi, Dev; Choi, Soyoung; Charusombat, Umarporn

    2009-01-01

    The purpose of this study was to investigate seventh grade students' conceptions of global warming and climate change. The study was descriptive in nature and involved the collection of qualitative data from 91 seventh grade students from three different schools in the Midwest, USA. An open response and draw and explain assessment instrument was…

  18. Strategic Reading Groups: Guiding Readers in the Middle Grades

    Science.gov (United States)

    Berne, Jennifer; Degener, Sophie C.

    2012-01-01

    Strategic grouping can transform reading instruction in the middle grades from a hit-or-miss learning experience to a targeted, responsive one. This book features a practical and field-tested model for small-group differentiated reading instruction in Grades 4-8. Jennifer Berne and Sophie C. Degener offer a clear, detailed discussion of how to…

  19. 30 CFR 816.105 - Backfilling and grading: Thick overburden.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Backfilling and grading: Thick overburden. 816...-SURFACE MINING ACTIVITIES § 816.105 Backfilling and grading: Thick overburden. (a) Definition. Thick... surrounding terrain. (b) Performance standards. Where thick overburden occurs within the permit area, the...

  20. 7 CFR 958.9 - Grade and size.

    Science.gov (United States)

    2010-01-01

    ... thereon. The term size also includes any of the sizes recognized by the onion trade in the production area. ... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE ONIONS GROWN IN CERTAIN DESIGNATED.... Grade means any of the officially established grades of onions, and size means any of the officially...

  1. A Preliminary Study of Grade Forecasting by Students

    Science.gov (United States)

    Armstrong, Michael J.

    2013-01-01

    This experiment enabled undergraduate business students to better assess their progress in a course by quantitatively forecasting their own end-of-course grades. This innovation provided them with predictive feedback in addition to the outcome feedback they were already receiving. A total of 144 students forecast their grades using an…

  2. Discrimination of Xihulongjing tea grade using an electronic tongue ...

    African Journals Online (AJOL)

    Five grades of Xihulongjing tea (grade: AAA, AA, A, B and C, from the same region and processed with the same processing method) were discriminated using -Astree II electronic tongue (e-tongue) coupled with pattern recognition methods including principal component analysis (PCA), canonical discriminant analysis ...

  3. Newspapers in Science Education: A Study Involving Sixth Grade Students

    Science.gov (United States)

    Lai, Ching-San; Wang, Yun-Fei

    2016-01-01

    The purpose of this study was to explore the learning performance of sixth grade elementary school students using newspapers in science teaching. A quasi-experimental design with a single group was used in this study. Thirty-three sixth grade elementary school students participated in this study. The research instruments consisted of three…

  4. Ideas: NCTM Standards-Based Instruction, Grades K-4.

    Science.gov (United States)

    Hynes, Michael C., Ed.

    This document is a collection of activity-based mathematics lessons for grades K-4 from the "Ideas" department in "Arithmetic Teacher: Mathematics Education through the Middle Grades." Each lesson includes background information, objectives, directions, extensions, and student worksheets. A matrix is included which correlates…

  5. Ideas: NCTM Standards-Based Instruction, Grades 5-8.

    Science.gov (United States)

    Hynes, Michael C., Ed.

    This document is a collection of activity-based mathematics lessons for grades 5-8 from the "Ideas" department in "Arithmetic Teacher: Mathematics Education through the Middle Grades." Each lesson includes background information, objectives, directions, extensions, and student worksheets. A matrix is included which correlates…

  6. Bladder cancer: epidemiology, staging and grading, and diagnosis.

    NARCIS (Netherlands)

    Kirkali, Z.; Chan, T.; Manoharan, M.; Algaba, F.; Busch, C.; Cheng, L.; Kiemeney, L.A.L.M.; Kriegmair, M.; Montironi, R.; Murphy, W.M.; Sesterhenn, I.A.; Tachibana, M.; Weider, J.

    2005-01-01

    Bladder cancer is a heterogeneous disease with a variable natural history. At one end of the spectrum, low-grade Ta tumors have a low progression rate and require initial endoscopic treatment and surveillance but rarely present a threat to the patient. At the other extreme, high-grade tumors have a

  7. Grade Repetition and Primary School Dropout in Uganda

    Science.gov (United States)

    Kabay, Sarah

    2016-01-01

    Research on education in low-income countries rarely focuses on grade repetition. When addressed, repetition is typically presented along with early school dropout as the "wasting" of educational resources. Simplifying grade repetition in this way often fails to recognize significant methodological concerns and also overlooks the unique…

  8. Effect of Cement Grades on some properties of Sandcrete ...

    African Journals Online (AJOL)

    The purpose of this study is to investigate the effects of cement grade on some properties of sandcrete. The cement used for this work was Ordinary Portland cement (Dangote brand) of grade 42.5 and 32.5 meeting the requirement of ASTM C150 type 1 cement. Three types of fine aggregate was also used to produce ...

  9. Grade Inflation: Too Much Talk, Too Little Action

    Science.gov (United States)

    Faurer, Judson C.; Lopez, Larry

    2009-01-01

    Grade inflation in academic institutions. Is it a subject so complex and pervasive in education that it defies resolution? The issue of grade inflation is of concern to college students, faculty, administrators and future employers. There is much gnashing of teeth, some veiled threats, wringing of hands, and both written and oral discussion of the…

  10. Evaluating the Quality of Transfer versus Nontransfer Accounting Principles Grades.

    Science.gov (United States)

    Colley, J. R.; And Others

    1996-01-01

    Using 1989-92 student records from three colleges accepting large numbers of transfers from junior schools into accounting, regression analyses compared grades of transfer and nontransfer students. Quality of accounting principle grades of transfer students was not equivalent to that of nontransfer students. (SK)

  11. Project Based Learning in Multi-Grade Class

    Science.gov (United States)

    Ciftci, Sabahattin; Baykan, Ayse Aysun

    2013-01-01

    The purpose of this study is to evaluate project based learning in multi-grade classes. This study, based on a student-centered learning approach, aims to analyze students' and parents' interpretations. The study was done in a primary village school belonging to the Centre of Batman, already adapting multi-grade classes in their education system,…

  12. Grade Non-Disclosure. NBER Working Paper No. 17465

    Science.gov (United States)

    Gottlieb, Daniel; Smetters, Kent

    2011-01-01

    This paper documents and explains the existence of grade non-disclosure policies in Masters in Business Administration programs, why these policies are concentrated in highly-ranked programs, and why these policies are not prevalent in most other professional degree programs. Related policies, including honors and minimum grade requirements, are…

  13. Clinical and molecular features of high-grade osteosarcoma

    NARCIS (Netherlands)

    Anninga, Jakob Klaas

    2013-01-01

    It can be concluded from this thesis that high-grade osteosarcoma is at clinical, pathological and molecular level a heterogeneous disease. To treat high-grade osteosarcoma, neo-adjuvant chemotherapy should be combined with radical surgery, irrespective the localization. There are only 4 effective

  14. The Value of Action Research in Middle Grades Education

    Science.gov (United States)

    Caskey, Micki M.

    2006-01-01

    Action research is one of the relevant methodologies for addressing research questions and issues in middle grades education. Accounting for nearly 20% of published middle grades research studies (Hough, 2003), action research has emerged as an important and appropriate research method. In addition to reviewing the historical context, this article…

  15. 7 CFR 27.9 - Marketing Services Offices; Grading Section.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Marketing Services Offices; Grading Section. 27.9 Section 27.9 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE....9 Marketing Services Offices; Grading Section. Marketing Services Offices shall be maintained at...

  16. Management of high-grade dysplasia in Barrett's esophagus.

    Science.gov (United States)

    Palley, S L; Sampliner, R E; Garewal, H S

    1989-08-01

    When Barrett's esophagus is complicated by adenocarcinoma, surgery is indicated in appropriate patients. Until now, high-grade dysplasia in Barrett's esophagus has been managed in a similar fashion. We explore this approach and review reported cases of high-grade dysplasia to suggest guidelines for collection of data to make future clinical decisions more rational.

  17. Relevance of standardization and grading in marketing of grains in ...

    African Journals Online (AJOL)

    This study examines the relevance of standardization and grading as a facilitating function in marketing of grains. The various measurement units, their acceptability and adoption by the consumers and traders along with the relationship of prices to different grades of grains was critically assessed. The study revealed that ...

  18. Upper Elementary Grades Bear the Brunt of Accountability

    Science.gov (United States)

    Anderson, Lorin W.

    2009-01-01

    Upper elementary teachers won't be surprised to learn that in every state, students enrolled in grades 3 through 8 bear the brunt of educational accountability. All states test all students at these grade levels in English/language arts and mathematics. Furthermore, an increasing number of states are testing students at selected elementary and…

  19. Identifying the professional knowledge base for multi-grade teaching ...

    African Journals Online (AJOL)

    This paper reports a small-scale qualitative study of teachers and teaching principals in multi-grade rural schools in Australia, focusing on identifying the professional knowledge base required for teachers in such contexts. Such a knowledge base is essential for improving the quality of multi-grade teaching. Interviews and ...

  20. A revision of the Cormack and Lehane laryngoscopic grading system with special consideration to grade II laryngoscopic view

    Directory of Open Access Journals (Sweden)

    Hussain khan Z

    2007-10-01

    Full Text Available Background: The major responsibility of an anesthesiologist is to provide adequate respiration for the patient. The most vital element in providing functional respiration is the airway. No anesthetic is safe unless diligent efforts are devoted to maintaining an intact functional airway. Difficult intubation had been classified into four grades, according to the view obtainable at laryngoscopy by Cormack and Lehane in 1984. This grading system has been in use to evaluate and manage those patients with difficult airway by anesthesiologists. In clinical state, grades III and IV are quite rare, so the need for a modified Cormack and Lehane grading system was felt. The use of a modified Cormack-Lehane scoring system of laryngoscopic views during direct laryngoscopy, was previously examined in the Western population. Koh and his co-workers had examined this modified Cormack and Lehane grading system in Asian population in a study in Singapore General Hospital. The aim of this study was to investigate this scoring system in Iranian patients.Methods: In a cross sectional study, a modified version of the Cormack and Lehane grading system was evaluated in 300 patients requiring tracheal intubation. In the modified system, grade II (only part of the glottis is visible was divided into IIa (part of the cords is visible and IIb (only the arytenoids or the very posterior origin of the cords are visible. Difficult intubation was defined as requiring more than one laryngoscopy or the use of special equipments.Results: Sixty eight patients (22.7% were scored as grade IIa and 32 (7.7% as grade IIb. The prevalence of difficult intubation in grade IIb was significantly higher than patients in group IIa (47.8% vs. 2.9% respectively, Fisher's exact test, p= 0.001Conclusion: The modified grading system provides more information than the original Cormack and Lehane system."n 

  1. Photodynamic therapy of Cervical Intraepithelial Neoplasia (CIN) high grade

    Science.gov (United States)

    Carbinatto, Fernanda M.; Inada, Natalia M.; Lombardi, Welington; da Silva, Eduardo V.; Belotto, Renata; Kurachi, Cristina; Bagnato, Vanderlei S.

    2016-02-01

    Cervical intraepithelial neoplasia (CIN) is the precursor of invasive cervical cancer and associated with human papillomavirus (HPV) infection. Photodynamic therapy (PDT) is a technique that has been used for the treatment of tumors. PDT is based on the accumulation of a photosensitizer in target cells that will generate cytotoxic reactive oxygen species upon illumination, inducing the death of abnormal tissue and PDT with less damaging to normal tissues than surgery, radiation, or chemotherapy and seems to be a promising alternative procedure for CIN treatment. The CIN high grades (II and III) presents potential indications for PDT due the success of PDT for CIN low grade treatment. The patients with CIN high grade that were treated with new clinic protocol shows lesion regression to CIN low grade 60 days after the treatment. The new clinical protocol using for treatment of CIN high grade shows great potential to become a public health technique.

  2. Modeling Erlang's Ideal Grading with Multirate BPP Traffic

    Directory of Open Access Journals (Sweden)

    Mariusz Glabowski

    2012-01-01

    Full Text Available This paper presents a complete methodology for modeling gradings (also called non-full-availability groups servicing single-service and multi-service traffic streams. The methodology worked out by the authors makes it possible to determine traffic characteristics of various types of gradings with state-dependent call arrival processes, including a new proposed structure of the Erlang’s Ideal Grading with the multirate links. The elaborated models of the gradings can be used for modeling different systems of modern networks, for example, the radio interfaces of the UMTS system, switching networks carrying a mixture of different multirate traffic streams, and video-on-demand systems. The results of the analytical calculations are compared with the results of the simulation data for selected gradings, which confirm high accuracy of the proposed methodology.

  3. Computer-Aided Grading of Lymphangioleiomyomatosis (LAM) using HRCT

    Science.gov (United States)

    Yao, Jianhua; Avila, Nilo; Dwyer, Andrew; Taveira-DaSilva, Angelo M.; Hathaway, Olanda M.; Moss, Joel

    2010-01-01

    Lymphangioleiomyomatosis (LAM) is a multisystem disorder associated with proliferation of smooth muscle-like cells, which leads to destruction of lung parenchyma. Subjective grading of LAM on HRCT is imprecise and can be arduous especially in cases with severe involvement. We propose a computer-aided evaluation system that grades LAM involvement based on analysis of lung texture patterns. A committee of support vector machines is employed for classification. The system was tested on 36 patients. The computer grade demonstrates good correlation with subjective radiologist grade (R=0.91, p<0.0001) and pulmonary functional tests (R=0.85, p<0.0001). The grade also provides precise progression assessment of disease over time. PMID:21625320

  4. Middle Grades Teachers' Use of Motivational Practices to Support Their Visions and Identities as Middle Grades Educators

    Science.gov (United States)

    Wall, Amanda; Miller, Samuel D.

    2015-01-01

    This qualitative case study explored 4 middle grades teachers' naïve theories of motivation, and the links between these theories and their thoughts and actions related to motivation. Their naïve theories of motivation stemmed from their overall visions for teaching, and their strong identities as middle grades educators. These naïve theories also…

  5. 7 CFR 868.310 - Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice...

    Science.gov (United States)

    2010-01-01

    ... Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice. (See also Â... Milled Rice Principles Governing Application of Standards § 868.310 Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice...

  6. Predicting different grades in different ways for selective admission : Disentangling the first-year grade point average

    NARCIS (Netherlands)

    Steenman, Sebastiaan C.; Bakker, Wieger E.; van Tartwijk, Jan W F

    2016-01-01

    The first-year grade point average (FYGPA) is the predominant measure of student success in most studies on university admission. Previous cognitive achievements measured with high school grades or standardized tests have been found to be the strongest predictors of FYGPA. For this reason,

  7. Predicting Different Grades in Different Ways for Selective Admission: Disentangling the First-Year Grade Point Average

    Science.gov (United States)

    Steenman, Sebastiaan C.; Bakker, Wieger E.; van Tartwijk, Jan W. F.

    2016-01-01

    The first-year grade point average (FYGPA) is the predominant measure of student success in most studies on university admission. Previous cognitive achievements measured with high school grades or standardized tests have been found to be the strongest predictors of FYGPA. For this reason, standardized tests measuring cognitive achievement are…

  8. Grade control and the determination of ore reserves at a low-grade uranium mine

    International Nuclear Information System (INIS)

    Reid, J.A.F.; Robertson, B.

    1982-01-01

    In 1966 an intensive exploration programme was conducted by Rio Tinto South Africa Ltd, involving airborne and ground radiometric surveys, percussion and diamond drilling, and pilot-plant tests. This investigation established the presence of a large deposit of low-grade uranium that could be mined on a large scale by open-pitting. Soon after production started in June 1974, it was realized that the original presentation of the ore reserves did not give a true reflection of the orebody. A comparison between the estimates and the ore mined from reserve blocks over the period 1975 to 1977 showed that the reserve grades were over-optimistic. In 1977 Rio Tinto Zinc Consultants were commissioned to re-evaluate the ore reserves from exploration diamond-drill data with the help of The Centre de Geostatistique at Fontainebleau, France. A new global reserve using disjunctive kriging techniques was developed, and is now the long-term reserve used for planning purposes at the Roessing Mine. For short-term planning, ore-reserve data are replaced by information from an intermediate drilling programme and blast-hole assays if these are available. A computerized short-term planning system has been established that reconciles the ore mined against the reserve blocks, as well as a system by which composited blast-hole assays are analysed for grade-control purposes. Owing to the complexity of the orebody, additional monitoring is achieved by the scanning of each truckload of ore with a group of scintillation crystal heads that evaluate the material mined

  9. Clinical grade adult stem cell banking.

    Science.gov (United States)

    Thirumala, Sreedhar; Goebel, W Scott; Woods, Erik J

    2009-07-01

    There has been a great deal of scientific interest recently generated by the potential therapeutic applications of adult stem cells in human care but there are several challenges regarding quality and safety in clinical applications and a number of these challenges relate to the processing and banking of these cells ex-vivo. As the number of clinical trials and the variety of adult cells used in regenerative therapy increases, safety remains a primary concern. This has inspired many nations to formulate guidelines and standards for the quality of stem cell collection, processing, testing, banking, packaging and distribution. Clinically applicable cryopreservation and banking of adult stem cells offers unique opportunities to advance the potential uses and widespread implementation of these cells in clinical applications. Most current cryopreservation protocols include animal serum proteins and potentially toxic cryoprotectant additives (CPAs) that prevent direct use of these cells in human therapeutic applications. Long term cryopreservation of adult stem cells under good manufacturing conditions using animal product free solutions is critical to the widespread clinical implementation of ex-vivo adult stem cell therapies. Furthermore, to avoid any potential cryoprotectant related complications, reduced CPA concentrations and efficient post-thaw washing to remove CPA are also desirable. The present review focuses on the current strategies and important aspects of adult stem cell banking for clinical applications. These include current good manufacturing practices (cGMPs), animal protein free freezing solutions, cryoprotectants, freezing & thawing protocols, viability assays, packaging and distribution. The importance and benefits of banking clinical grade adult stem cells are also discussed.

  10. Comprehensive, Integrative Genomic Analysis of Diffuse Lower-Grade Gliomas.

    Science.gov (United States)

    Brat, Daniel J; Verhaak, Roel G W; Aldape, Kenneth D; Yung, W K Alfred; Salama, Sofie R; Cooper, Lee A D; Rheinbay, Esther; Miller, C Ryan; Vitucci, Mark; Morozova, Olena; Robertson, A Gordon; Noushmehr, Houtan; Laird, Peter W; Cherniack, Andrew D; Akbani, Rehan; Huse, Jason T; Ciriello, Giovanni; Poisson, Laila M; Barnholtz-Sloan, Jill S; Berger, Mitchel S; Brennan, Cameron; Colen, Rivka R; Colman, Howard; Flanders, Adam E; Giannini, Caterina; Grifford, Mia; Iavarone, Antonio; Jain, Rajan; Joseph, Isaac; Kim, Jaegil; Kasaian, Katayoon; Mikkelsen, Tom; Murray, Bradley A; O'Neill, Brian Patrick; Pachter, Lior; Parsons, Donald W; Sougnez, Carrie; Sulman, Erik P; Vandenberg, Scott R; Van Meir, Erwin G; von Deimling, Andreas; Zhang, Hailei; Crain, Daniel; Lau, Kevin; Mallery, David; Morris, Scott; Paulauskis, Joseph; Penny, Robert; Shelton, Troy; Sherman, Mark; Yena, Peggy; Black, Aaron; Bowen, Jay; Dicostanzo, Katie; Gastier-Foster, Julie; Leraas, Kristen M; Lichtenberg, Tara M; Pierson, Christopher R; Ramirez, Nilsa C; Taylor, Cynthia; Weaver, Stephanie; Wise, Lisa; Zmuda, Erik; Davidsen, Tanja; Demchok, John A; Eley, Greg; Ferguson, Martin L; Hutter, Carolyn M; Mills Shaw, Kenna R; Ozenberger, Bradley A; Sheth, Margi; Sofia, Heidi J; Tarnuzzer, Roy; Wang, Zhining; Yang, Liming; Zenklusen, Jean Claude; Ayala, Brenda; Baboud, Julien; Chudamani, Sudha; Jensen, Mark A; Liu, Jia; Pihl, Todd; Raman, Rohini; Wan, Yunhu; Wu, Ye; Ally, Adrian; Auman, J Todd; Balasundaram, Miruna; Balu, Saianand; Baylin, Stephen B; Beroukhim, Rameen; Bootwalla, Moiz S; Bowlby, Reanne; Bristow, Christopher A; Brooks, Denise; Butterfield, Yaron; Carlsen, Rebecca; Carter, Scott; Chin, Lynda; Chu, Andy; Chuah, Eric; Cibulskis, Kristian; Clarke, Amanda; Coetzee, Simon G; Dhalla, Noreen; Fennell, Tim; Fisher, Sheila; Gabriel, Stacey; Getz, Gad; Gibbs, Richard; Guin, Ranabir; Hadjipanayis, Angela; Hayes, D Neil; Hinoue, Toshinori; Hoadley, Katherine; Holt, Robert A; Hoyle, Alan P; Jefferys, Stuart R; Jones, Steven; Jones, Corbin D; Kucherlapati, Raju; Lai, Phillip H; Lander, Eric; Lee, Semin; Lichtenstein, Lee; Ma, Yussanne; Maglinte, Dennis T; Mahadeshwar, Harshad S; Marra, Marco A; Mayo, Michael; Meng, Shaowu; Meyerson, Matthew L; Mieczkowski, Piotr A; Moore, Richard A; Mose, Lisle E; Mungall, Andrew J; Pantazi, Angeliki; Parfenov, Michael; Park, Peter J; Parker, Joel S; Perou, Charles M; Protopopov, Alexei; Ren, Xiaojia; Roach, Jeffrey; Sabedot, Thaís S; Schein, Jacqueline; Schumacher, Steven E; Seidman, Jonathan G; Seth, Sahil; Shen, Hui; Simons, Janae V; Sipahimalani, Payal; Soloway, Matthew G; Song, Xingzhi; Sun, Huandong; Tabak, Barbara; Tam, Angela; Tan, Donghui; Tang, Jiabin; Thiessen, Nina; Triche, Timothy; Van Den Berg, David J; Veluvolu, Umadevi; Waring, Scot; Weisenberger, Daniel J; Wilkerson, Matthew D; Wong, Tina; Wu, Junyuan; Xi, Liu; Xu, Andrew W; Yang, Lixing; Zack, Travis I; Zhang, Jianhua; Aksoy, B Arman; Arachchi, Harindra; Benz, Chris; Bernard, Brady; Carlin, Daniel; Cho, Juok; DiCara, Daniel; Frazer, Scott; Fuller, Gregory N; Gao, JianJiong; Gehlenborg, Nils; Haussler, David; Heiman, David I; Iype, Lisa; Jacobsen, Anders; Ju, Zhenlin; Katzman, Sol; Kim, Hoon; Knijnenburg, Theo; Kreisberg, Richard Bailey; Lawrence, Michael S; Lee, William; Leinonen, Kalle; Lin, Pei; Ling, Shiyun; Liu, Wenbin; Liu, Yingchun; Liu, Yuexin; Lu, Yiling; Mills, Gordon; Ng, Sam; Noble, Michael S; Paull, Evan; Rao, Arvind; Reynolds, Sheila; Saksena, Gordon; Sanborn, Zack; Sander, Chris; Schultz, Nikolaus; Senbabaoglu, Yasin; Shen, Ronglai; Shmulevich, Ilya; Sinha, Rileen; Stuart, Josh; Sumer, S Onur; Sun, Yichao; Tasman, Natalie; Taylor, Barry S; Voet, Doug; Weinhold, Nils; Weinstein, John N; Yang, Da; Yoshihara, Kosuke; Zheng, Siyuan; Zhang, Wei; Zou, Lihua; Abel, Ty; Sadeghi, Sara; Cohen, Mark L; Eschbacher, Jenny; Hattab, Eyas M; Raghunathan, Aditya; Schniederjan, Matthew J; Aziz, Dina; Barnett, Gene; Barrett, Wendi; Bigner, Darell D; Boice, Lori; Brewer, Cathy; Calatozzolo, Chiara; Campos, Benito; Carlotti, Carlos Gilberto; Chan, Timothy A; Cuppini, Lucia; Curley, Erin; Cuzzubbo, Stefania; Devine, Karen; DiMeco, Francesco; Duell, Rebecca; Elder, J Bradley; Fehrenbach, Ashley; Finocchiaro, Gaetano; Friedman, William; Fulop, Jordonna; Gardner, Johanna; Hermes, Beth; Herold-Mende, Christel; Jungk, Christine; Kendler, Ady; Lehman, Norman L; Lipp, Eric; Liu, Ouida; Mandt, Randy; McGraw, Mary; Mclendon, Roger; McPherson, Christopher; Neder, Luciano; Nguyen, Phuong; Noss, Ardene; Nunziata, Raffaele; Ostrom, Quinn T; Palmer, Cheryl; Perin, Alessandro; Pollo, Bianca; Potapov, Alexander; Potapova, Olga; Rathmell, W Kimryn; Rotin, Daniil; Scarpace, Lisa; Schilero, Cathy; Senecal, Kelly; Shimmel, Kristen; Shurkhay, Vsevolod; Sifri, Suzanne; Singh, Rosy; Sloan, Andrew E; Smolenski, Kathy; Staugaitis, Susan M; Steele, Ruth; Thorne, Leigh; Tirapelli, Daniela P C; Unterberg, Andreas; Vallurupalli, Mahitha; Wang, Yun; Warnick, Ronald; Williams, Felicia; Wolinsky, Yingli; Bell, Sue; Rosenberg, Mara; Stewart, Chip; Huang, Franklin; Grimsby, Jonna L; Radenbaugh, Amie J; Zhang, Jianan

    2015-06-25

    Diffuse low-grade and intermediate-grade gliomas (which together make up the lower-grade gliomas, World Health Organization grades II and III) have highly variable clinical behavior that is not adequately predicted on the basis of histologic class. Some are indolent; others quickly progress to glioblastoma. The uncertainty is compounded by interobserver variability in histologic diagnosis. Mutations in IDH, TP53, and ATRX and codeletion of chromosome arms 1p and 19q (1p/19q codeletion) have been implicated as clinically relevant markers of lower-grade gliomas. We performed genomewide analyses of 293 lower-grade gliomas from adults, incorporating exome sequence, DNA copy number, DNA methylation, messenger RNA expression, microRNA expression, and targeted protein expression. These data were integrated and tested for correlation with clinical outcomes. Unsupervised clustering of mutations and data from RNA, DNA-copy-number, and DNA-methylation platforms uncovered concordant classification of three robust, nonoverlapping, prognostically significant subtypes of lower-grade glioma that were captured more accurately by IDH, 1p/19q, and TP53 status than by histologic class. Patients who had lower-grade gliomas with an IDH mutation and 1p/19q codeletion had the most favorable clinical outcomes. Their gliomas harbored mutations in CIC, FUBP1, NOTCH1, and the TERT promoter. Nearly all lower-grade gliomas with IDH mutations and no 1p/19q codeletion had mutations in TP53 (94%) and ATRX inactivation (86%). The large majority of lower-grade gliomas without an IDH mutation had genomic aberrations and clinical behavior strikingly similar to those found in primary glioblastoma. The integration of genomewide data from multiple platforms delineated three molecular classes of lower-grade gliomas that were more concordant with IDH, 1p/19q, and TP53 status than with histologic class. Lower-grade gliomas with an IDH mutation either had 1p/19q codeletion or carried a TP53 mutation. Most

  11. MR detection of retinal hemorrhages: correlation with graded ophthalmologic exam

    International Nuclear Information System (INIS)

    Beavers, Angela J.; Allbery, Sandra M.; Stagner, Anna M.; Hejkal, Thomas W.; Lyden, Elizabeth R.; Haney, Suzanne B.

    2015-01-01

    Dilated fundoscopic exam is considered the gold standard for detecting retinal hemorrhage, but expertise in obtaining this exam is not always immediately available. MRI can detect retinal hemorrhages, but correlation of the grade or severity of retinal hemorrhage on dilated fundoscopic exam with retinal hemorrhage visibility on MRI has not been described. To determine the value of standard brain protocol MRI in detecting retinal hemorrhage and to determine whether there is any correlation with MR detection of retinal hemorrhage and the dilated fundoscopic exam grade of hemorrhage. We conducted a retrospective chart review of 77 children <2 years old who were seen for head trauma from April 2007 to July 2013 and had both brain MRI and dilated fundoscopic exam or retinal camera images. A staff pediatric radiologist and radiology resident reviewed the MR images. Retinal hemorrhages were graded by a chief ophthalmology resident on a 12-point scale based on the retinal hemorrhage type, size, location and extent as seen on review of retinal camera images and detailed reports by ophthalmologists. Higher scores indicated increased severity of retinal hemorrhages. There was a statistically significant difference in the median grade of retinal hemorrhage examination between children who had retinal hemorrhage detected on MRI and children who did not have retinal hemorrhage detected on MRI (P = 0.02). When examination grade was categorized as low-grade (1-4), moderate-grade (5-8) or high-grade (>8) hemorrhage, there was a statistically significant association between exam grade and diagnosis based on MRI (P = 0.008). For example, only 14% of children with low-grade retinal hemorrhages were identified on MRI compared to 76% of children with high-grade hemorrhages. MR detection of retinal hemorrhage demonstrated a sensitivity of 61%, specificity of 100%, positive predictive value of 100% and negative predictive value of 63%. Retinal hemorrhage was best seen on the gradient

  12. DIFFERENT LEVEL OF LEARNED-HELPLESSNESS AMONG HIGH SCHOOL STUDENTS WITH LOWER GRADE AND HIGHER GRADE IN SALATIGA INDONESIA

    Directory of Open Access Journals (Sweden)

    Berta Esti Ari Prasetya

    2013-06-01

    consisted of 190 of higher grade students and 127 of lower grade students. Mann-Whitney U was used to analyse the data, considering that the data were not normally distributed. This test result showed that there was a significant difference between high school students with higher grade and lower grade (the Mann-Whitney U coefficient of 10,644, with z value of -1795, p <0.05 (p = 0036, 1-tailed, with students of lower grade tend to be more prone to experience learned-helplessness. Additional results from their subjective perception on their achievement were also discussed and so were the implications of the study.

  13. Facing Contrast-Enhancing Gliomas: Perfusion MRI in Grade III and Grade IV Gliomas according to Tumor Area

    Directory of Open Access Journals (Sweden)

    Anna Luisa Di Stefano

    2014-01-01

    Full Text Available Tumoral neoangiogenesis characterizes high grade gliomas. Relative Cerebral Blood Volume (rCBV, calculated with Dynamic Susceptibility Contrast (DSC Perfusion-Weighted Imaging (PWI, allows for the estimation of vascular density over the tumor bed. The aim of the study was to characterize putative tumoral neoangiogenesis via the study of maximal rCBV with a Region of Interest (ROI approach in three tumor areas—the contrast-enhancing area, the nonenhancing tumor, and the high perfusion area on CBV map—in patients affected by contrast-enhancing glioma (grades III and IV. Twenty-one patients were included: 15 were affected by grade IV and 6 by grade III glioma. Maximal rCBV values for each patient were averaged according to glioma grade. Although rCBV from contrast-enhancement and from nonenhancing tumor areas was higher in grade IV glioma than in grade III (5.58 and 2.68; 3.01 and 2.2, resp., the differences were not significant. Instead, rCBV recorded in the high perfusion area on CBV map, independently of tumor compartment, was significantly higher in grade IV glioma than in grade III (7.51 versus 3.78, P=0.036. In conclusion, neoangiogenesis encompasses different tumor compartments and CBV maps appear capable of best characterizing the degree of neovascularization. Facing contrast-enhancing brain tumors, areas of high perfusion on CBV maps should be considered as the reference areas to be targeted for glioma grading.

  14. The value of intraoperative sonography in low grade glioma surgery.

    Science.gov (United States)

    Petridis, Athanasios K; Anokhin, Maxim; Vavruska, Jan; Mahvash, Mehran; Scholz, Martin

    2015-04-01

    There is a number of different methods to localize a glioma intraoperatively. Neuronavigation, intraoperative MRI, 5-aminolevulinic acid, as well as intraoperative sonography. Every method has its advantages and disadvantages. Low grade gliomas do not show a specific signal with 5-aminolevulinic acid and are difficult to distinguish macroscopically from normal tissue. In the present study we stress out the importance of intraoperative diagnostic ultrasound for localization of low grade gliomas. We retrospectively evaluated the charts and MRIs of 34 patients with low grade gliomas operated in our department from 2011 until December 2014. The efficacy of ultrasound as an intraoperative navigational tool was assessed. In 15 patients ultrasound was used and in 19 not. Only histologically proven low grades gliomas (astrocytomas grade II) were evaluated. In none of the patients where ultrasound (combined with neuronavigation) was used (N=15) to find the tumors, the target was missed, whereas the exclusive use of neuronavigation missed the target in 5 of 19 cases of small subcortical low grade gliomas. Intraoperative ultrasound is an excellent tool in localizing low grade gliomas intraoperatively. It is an inexpensive, real time neuronavigational tool, which overcomes brain shift. Even when identifying the tumors with ultrasound is very reliable, the extend of resection and the decision to remove any residual tumor with the help of ultrasound is at the moment unreliable. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Ceramic/polymer functionally graded material (FGM) lightweight armor system

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, J.J.; McClellan, K.J.

    1998-12-31

    This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). Functionally graded material is an enabling technology for lightweight body armor improvements. The objective was to demonstrate the ability to produce functionally graded ceramic-polymer and ceramic-metal lightweight armor materials. This objective involved two aspects. The first and key aspect was the development of graded-porosity boron-carbide ceramic microstructures. The second aspect was the development of techniques for liquid infiltration of lightweight metals and polymers into the graded-porosity ceramic. The authors were successful in synthesizing boron-carbide ceramic microstructures with graded porosity. These graded-porosity boron-carbide hot-pressed pieces were then successfully liquid-infiltrated in vacuum with molten aluminum at 1,300 C, and with liquid polymers at room temperature. Thus, they were able to demonstrate the feasibility of producing boron carbide-aluminum and boron carbide-polymer functionally graded materials.

  16. Multi-Input Convolutional Neural Network for Flower Grading

    Directory of Open Access Journals (Sweden)

    Yu Sun

    2017-01-01

    Full Text Available Flower grading is a significant task because it is extremely convenient for managing the flowers in greenhouse and market. With the development of computer vision, flower grading has become an interdisciplinary focus in both botany and computer vision. A new dataset named BjfuGloxinia contains three quality grades; each grade consists of 107 samples and 321 images. A multi-input convolutional neural network is designed for large scale flower grading. Multi-input CNN achieves a satisfactory accuracy of 89.6% on the BjfuGloxinia after data augmentation. Compared with a single-input CNN, the accuracy of multi-input CNN is increased by 5% on average, demonstrating that multi-input convolutional neural network is a promising model for flower grading. Although data augmentation contributes to the model, the accuracy is still limited by lack of samples diversity. Majority of misclassification is derived from the medium class. The image processing based bud detection is useful for reducing the misclassification, increasing the accuracy of flower grading to approximately 93.9%.

  17. Affix Meaning Knowledge in First Through Third Grade Students.

    Science.gov (United States)

    Apel, Kenn; Henbest, Victoria Suzanne

    2016-04-01

    We examined grade-level differences in 1st- through 3rd-grade students' performance on an experimenter-developed affix meaning task (AMT) and determined whether AMT performance explained unique variance in word-level reading and reading comprehension, beyond other known contributors to reading development. Forty students at each grade level completed an assessment battery that included measures of phonological awareness, receptive vocabulary, word-level reading, reading comprehension, and affix meaning knowledge. On the AMT, 1st-grade students were significantly less accurate than 2nd- and 3rd-grade students; there was no significant difference in performance between the 2nd- and 3rd-grade students. Regression analyses revealed that the AMT accounted for 8% unique variance of students' performance on word-level reading measures and 6% unique variance of students' performance on the reading comprehension measure, after age, phonological awareness, and receptive vocabulary were explained. These results provide initial information on the development of affix meaning knowledge via an explicit measure in 1st- through 3rd-grade students and demonstrate that affix meaning knowledge uniquely contributes to the development of reading abilities above other known literacy predictors. These findings provide empirical support for how students might use morphological problem solving to read unknown multimorphemic words successfully.

  18. Grade Level and Gender Differences in a School-Based Reading Tutoring Program

    Science.gov (United States)

    Chang, Sau Hou

    2011-01-01

    The purpose of the present study is to investigate the grade level and gender differences in a school-based reading tutoring program. The treatment group included 10 first-grade and 12 second-grade struggling readers, and the control group included 41 first-grade and 63 second-grade nonstruggling readers. The tutors were teacher candidates in an…

  19. A discussion on several problems in determination of uranium ore grade criteria

    International Nuclear Information System (INIS)

    Zhu Zhixiang.

    1991-01-01

    The course of determination of uranium ore grade criteria in China is briefly introduced. The cut-off grade minimum industrial grade and allowable minimum average grade uranium ore bodies used in China are reviewed. The meanings and role of various grade criteria and their economic basis for determination in uranium exploration, mining and sorting are discussed and the author's ideas are given

  20. Receipt of special education services following elementary school grade retention.

    Science.gov (United States)

    Silverstein, Michael; Guppy, Nicole; Young, Robin; Augustyn, Marilyn

    2009-06-01

    To estimate the proportion of children who receive an Individualized Education Program (IEP) following grade retention in elementary school. Longitudinal cohort study. Children retained in kindergarten or first (K/1) grade and third grade, presumably for academic reasons, were followed up through fifth grade. Presence or absence of an IEP. A total of 300 children retained in K/1 and 80 retained in third grade were included in the study. Of the K/1 retainees, 68.9% never received an IEP during the subsequent 4 to 5 years; of the third-grade retainees, 72.3% never received an IEP. Kindergarten/first-grade retainees in the highest quintile for socioeconomic status and those with suburban residence were less likely to receive an IEP than retained children in all other socioeconomic status quintiles (adjusted odds ratio, 0.17; 95% confidence interval, 0.05-0.62) and in rural communities (0.16; 0.06-0.44). Among K/1 retainees with persistently low academic achievement in math and reading, as assessed by standardized testing, 38.2% and 29.7%, respectively, never received an IEP. Most children retained in K/1 or third grade for academic reasons, including many of those who demonstrated sustained academic difficulties, never received an IEP during elementary school. Further studies are important to elucidate whether retained elementary schoolchildren are being denied their rights to special education services. In the meantime, early-grade retention may provide an opportunity for pediatricians to help families advocate for appropriate special education evaluations for children experiencing school difficulties.