Facile Synthesis of Magnetic Copolymer Microspheres Based on Poly(glycidyl methacrylate-co-N-isopropylacrylamide/Fe3O4 by Suspension Photopolymerization

Directory of Open Access Journals (Sweden)

Siti Zulaikha Mazlan

2014-01-01

Full Text Available Magnetic copolymer based on poly(glycidyl methacrylate-co-N-isopropylacrylamide microspheres was prepared by 2,2-dimethoxy-2-phenylacetophenone- (DMPP- photo initiated and poly(vinyl alcohol- (PVA- stabilized single step suspension photopolymerization. The effect of chemical interaction, morphology, and thermal properties by adding 0.1% w/v Fe3O4 in the copolymer was investigated. Infrared analysis (FTIR showed that (C=C band disappeared after copolymerization, indicating that the magnetic copolymer microspheres were successfully synthesized and two important bands at 908 cm−1 and 1550 cm−1 appear. These are associated with the epoxy group stretching of GMA and secondary amide (N–H/C–H deformation vibration of NIPAAm in magnetic microspheres. The X-ray diffraction (XRD result proved the incorporation of Fe3O4 nanoparticles with copolymer microspheres as peak of Fe3O4 was observed. Morphology study revealed that magnetic copolymer exhibited uniform spheres and smoother appearance when entrapped with Fe3O4 nanoparticles. The lowest percentage of Fe3O4 nanoparticles leached from the copolymer microspheres was obtained at pH 7. Finally, thermal property of the copolymer microspheres was improved by adding a small amount of Fe3O4 nanoparticles that has been shown from the thermogram.

Miscibility and specific interactions in blends of poly(n-vinyl-2-pyrrolidone) and acid functional polyester resins.

NARCIS (Netherlands)

Senatore, D.; Berix, M.J.A.; Laven, J.; Benthem, van R.A.T.M.; With, de G.; Mezari, B.; Magusin, P.C.M.M.

2008-01-01

Miscibility and intermol. interactions of novel blends of poly(N-vinyl-2-pyrrolidone) (PVP) and acid functional polyester resins (APE) were studied by use of Differential Scanning Calorimetry (DSC), Attenuated Total Reflectance Fourier Transform IR (ATR-FTIR), Cross-Polarization Magic Angle Spinning

Silica-coated poly(glycidyl methacrylate-ethylene dimethacrylate) beads containing organic phase change materials

Czech Academy of Sciences Publication Activity Database

Feczkó, T.; Trif, L.; Németh, B.; Horák, Daniel

2016-01-01

Roč. 641, 10 October (2016), s. 24-28 ISSN 0040-6031 Institutional support: RVO:61389013 Keywords : porous poly(glycidyl methacrylate-ethylene dimethacrylate) beads * paraffin * cetyl alcohol Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.236, year: 2016

The γ-radiation induced grafting of unsaturated segmented polyurethanes with N-vinyl pyrrolidone

International Nuclear Information System (INIS)

Egboh, S.H.; George, M.H.; Barrie, J.A.

1984-01-01

Linear unsaturated segmented polyurethanes have been modified by hydrophilic grafting at 40 deg C with N-vinyl pyrrolidone, in N,N-dimethylformamide as solvent, using 60 Cobalt γ-irradiation. Graft copolymers were isolated from homopolymers by selective solvent extraction using a Soxhlet apparatus. The effects of reaction time, total dose, temperature and monomer concentration, on the graft yields have been examined. Relatively high irradiation doses were avoided during the grafting experiments to prevent possible degradation of the segmented polyurethanes and gelation of the homopolymer, poly(N-vinyl pyrrolidone). The ungrafted and grafted copolymers were characterized, and the graft copolymers were shown to be more thermally stable than the original polyurethanes, by thermogravimetric analysis. An explanation for the observed variation of the graft yields with some of the experimental variables is suggested. (author)

Integrated antifouling and bactericidal polymer membranes through bioinspired polydopamine/poly(N-vinyl pyrrolidone) coating

International Nuclear Information System (INIS)

Wang, Xianghong; Yuan, Shuaishuai; Shi, Dean; Yang, Yingkui; Jiang, Tao; Yan, Shunjie; Shi, Hengchong; Luan, Shifang; Yin, Jinghua

2016-01-01

Graphical abstract: - Highlights: • Antifouling and bactericidal capabilities were facilely integrated into a surface via bioinspired coating. • The modification technique was very facile and universal to different types of substrate materials. • The integrated antifouling and bactericidal surfaces have great potential in wound dressing applications. - Abstract: Polypropylene (PP) non-woven has been widely used as wound dressing; however, the hydrophobic nature of PP can initiate bacterial attachment and subsequent biofilm formation. Herein, we propose a facile approach to functionalize PP non-woven with poly(ethylene glycol) (PEG) and poly(N-vinyl pyrrolidone)-iodine complex (PVP-I). PVP and PEG were successively tethered onto PP non-woven surface via versatile bioinspired dopamine (DA) chemistry, followed by complexing iodine with PVP moieties. It was demonstrated through the field emission scanning electron microscope (SEM) and spread plate method that the as-modified PP non-woven integrated both antifouling property of PEG for suppressing bacterial adhesion, and bactericidal property of PVP-I for killing the few adherent bacteria. Meanwhile, it could greatly resist platelet and red blood cell adhesion. The integrated antifouling and bactericidal PP non-woven surfaces might have great potential in various wound dressing applications.

Integrated antifouling and bactericidal polymer membranes through bioinspired polydopamine/poly(N-vinyl pyrrolidone) coating

Energy Technology Data Exchange (ETDEWEB)

Wang, Xianghong [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Faculty of Materials Science and Engineering, Hubei University, Wuhan 430062 (China); Yuan, Shuaishuai [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Shi, Dean, E-mail: deanshi2012@yahoo.com [Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Faculty of Materials Science and Engineering, Hubei University, Wuhan 430062 (China); Yang, Yingkui; Jiang, Tao [Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Faculty of Materials Science and Engineering, Hubei University, Wuhan 430062 (China); Yan, Shunjie; Shi, Hengchong [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Luan, Shifang, E-mail: sfluan@ciac.ac.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Yin, Jinghua [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2016-07-01

Graphical abstract: - Highlights: • Antifouling and bactericidal capabilities were facilely integrated into a surface via bioinspired coating. • The modification technique was very facile and universal to different types of substrate materials. • The integrated antifouling and bactericidal surfaces have great potential in wound dressing applications. - Abstract: Polypropylene (PP) non-woven has been widely used as wound dressing; however, the hydrophobic nature of PP can initiate bacterial attachment and subsequent biofilm formation. Herein, we propose a facile approach to functionalize PP non-woven with poly(ethylene glycol) (PEG) and poly(N-vinyl pyrrolidone)-iodine complex (PVP-I). PVP and PEG were successively tethered onto PP non-woven surface via versatile bioinspired dopamine (DA) chemistry, followed by complexing iodine with PVP moieties. It was demonstrated through the field emission scanning electron microscope (SEM) and spread plate method that the as-modified PP non-woven integrated both antifouling property of PEG for suppressing bacterial adhesion, and bactericidal property of PVP-I for killing the few adherent bacteria. Meanwhile, it could greatly resist platelet and red blood cell adhesion. The integrated antifouling and bactericidal PP non-woven surfaces might have great potential in various wound dressing applications.

Poly(N-vinyl-2-pyrrolidone)-stabilized palladium-platinum nanoparticles-catalyzed hydrolysis of ammonia borane for hydrogen generation

Science.gov (United States)

Rakap, Murat

2015-02-01

The catalytic use of highly efficient poly(N-vinyl-2-pyrrolidone)-stabilized palladium-platinum nanoparticles (4.2 ± 1.9 nm) in the hydrolysis of ammonia-borane is reported. The catalyst is prepared by co-reduction of two metal ions in ethanol/water mixture by an alcohol reduction method and characterized by transmission electron microscopy, X-ray photoelectron spectroscopy and UV-Vis spectroscopy. They are recyclable and highly active for hydrogen generation from the hydrolysis of ammonia-borane even at very low concentrations and temperature, providing a record numbers of average turnover frequency value (125 mol H2/mol cat.min-1) and maximum hydrogen generation rate (3468 L H2 min-1 (mol cat)-1). They also provide activation energy of 51.7 ± 2 kJ/mol for the hydrolysis of ammonia borane.

Synthesis and characterization of UV photocrosslinkable hydrogels with poly(N-vinyl-2-pyrrolidone): Determination of the network mesh size distribution

DEFF Research Database (Denmark)

Marizza, Paolo; Abrami, M.; Keller, Stephan Sylvest

2016-01-01

Hydrogels of poly(n-vinyl-2-pyrrolidone) were produced by UV irradiation of aqueous solutions of the polymer in presence of hydrogen peroxide, used as initiator. The mechanical and the nanostructural properties of the gels were characterized by a combination of experimental techniques including...

Textural properties of poly(glycidyl methacrylate) : acid-modified bentonite nanocomposites

NARCIS (Netherlands)

Zunic, M.; Milutinovic-Nikolic, A.; Nastasovic, A.; Vukovic, Z.; Loncarevic, D.; Vukovic, I.; Loos, K.; ten Brinke, G.; Jovanovic, D.; Sharma, Bhaskar; Ubaghs, Luc; Keul, Helmut; Höcker, Hartwig; Loontjens, Ton; Benthem, Rolf van; Žunić, M.; Milutinović-Nikolić, A.; Nastasović, A.; Vuković, Z.; Lončarević, D.; Vuković, I.; Jovanović, D.

The aim of this study was to obtain enhanced textural properties of macroporous crosslinked copolymer poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) by synthesizing nanocomposites with acid-modified bentonite. Nanocomposites were obtained by introducing various amounts of

Determination of N-vinyl-2-pyrrolidone and N-methyl-2-pyrrolidone in drugs using polypyrrole-based headspace solid-phase microextraction and gas chromatography-nitrogen-phosphorous detection.

Science.gov (United States)

Mehdinia, Ali; Ghassempour, Alireza; Rafati, Hasan; Heydari, Rouhollah

2007-03-21

A headspace solid-phase microextraction and gas chromatography-nitrogen-phosphorous detection (HS-SPME-GC-NPD) method using polypyrrole (PPy) fibers has been introduced to determine two derivatives of pyrrolidone; N-vinyl-2-pyrrolidone (NVP) and N-methyl-2-pyrrolidone (NMP). Two types of PPy fibers, prepared using organic and aqueous media, were compared in terms of extraction efficiency and thermal stability. It was found that PPy film prepared using organic medium (i.e. acetonitrile) had higher extraction efficiency and more thermal stability compared to the film prepared in aqueous medium. To enhance the sensitivity of HS-SPME, the effects of pH, ionic strength, extraction time, extraction temperature and the headspace volume on the extraction efficiency were optimized. Using the results of this research, high sensitivity and selectivity had been achieved due to the combination of the high extraction efficiency of PPy film prepared in organic medium and the high sensitivity and selectivity of nitrogen-phosphorous detection. Linear range of the analytes was found to be between 1.0 and 1000 microg L(-1) with regression coefficients (R(2)) of 0.998 and 0.997 for NVP and NMP, consequently. Limits of detection (LODs) were 0.074 and 0.081 microg L(-1) for NVP and NMP, respectively. Relative standard deviation (R.S.D.) for five replications of analyses was found to be less than 6.0%. In real samples the mean recoveries were 94.81% and 94.15% for NVP and NMP, respectively. The results demonstrated the suitability of the HS-SPME technique for analyzing NVP and NMP in two different pharmaceutical matrices. In addition, the method was used for simultaneous detection of NVP, 2-pyrrolidone (2-Pyr), gamma-butyrolactone (GBL) and ethanolamine (EA) compounds.

Decreased material-activation of the complement system using low-energy plasma polymerized poly(vinyl pyrrolidone) coatings

DEFF Research Database (Denmark)

Andersen, T.E.; Kolmos, H.J.; Palarasah, Yaseelan

2011-01-01

In the current study we investigate the activation of blood complement on medical device silicone rubber and present a plasma polymerized vinyl pyrrolidone (ppVP) coating which strongly decreases surface-activation of the blood complement system. We show that uncoated silicone and polystyrene...... surface. The ppVP surface is furthermore characterized physically and chemically using scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR), which indicates preservation of chemical functionality by the applied plasma process. Overall, the pp...

Immobilization of α-amylase onto poly(glycidyl methacrylate) grafted electrospun fibers by ATRP

International Nuclear Information System (INIS)

Oktay, Burcu; Demir, Serap; Kayaman-Apohan, Nilhan

2015-01-01

In this study, novel α-amylase immobilized poly(vinyl alcohol) (PVA) nanofibers were prepared. The PVA nanofiber surfaces were functionalized with 2-bromoisobutyryl bromide (BiBBr) and followed by surface initiated atom transfer radical polymerization (SI-ATRP) of glycidyl methacrylate (GMA). The morphology of the poly(glycidyl methacrylate) (PGMA) grafted PVA nanofibers was characterized by scanning electron microscopy (SEM). Also PGMA brushes were confirmed by X-ray photo electron microscopy (XPS). α-Amylase was immobilized in a one step process onto the PGMA grafted PVA nanofiber. The characteristic properties of the immobilized and free enzymes were examined. The thermal stability of the enzyme was improved and showed maximum activity at 37 °C by immobilization. pH values of the maximum activity of the free and immobilized enzymes were also found at 6.0 and 6.5, respectively. Free enzyme lost its activity completely within 15 days. The immobilized enzyme lost only 23.8% of its activity within 30 days. - Highlights: • Electrospun photocrosslinkable PVA nanofiber was prepared. • PGMA brushes were conducted on PVA nanofiber via SI-ATRP. • The immobilized enzyme showed maximum activity at pH 6.0 and at 37 °C. • Functionalized nanofibers may be used as promising supports for enzyme immobilization

Effect of different plasticizers on poly(N-vinyl-2-pyrrolidone) hydrogels cross-linked by radiation

International Nuclear Information System (INIS)

Alcantara, Mara Tania S.; Giannini, Danielle R.; Brant, Antonio J.C.; Riella, Humberto G.; Lugao, Ademar B.

2011-01-01

The use of hydrogel membranes usually demands polymers capable of forming films with high elastic and flexible properties besides having high water absorption. In terms of improvements of polymer plasticity, addition of special plasticizers to polymers can do it with promising results, although within limits of concentrations. The objective of this study was to evaluate the different effects of poly(enthylene glycol) (PEG) and glycerol as plasticizers on hydrogel membranes synthesized from poly(N-vinyl-2-pyrrolidone) (PVP) as the main polymer in aqueous polymeric solutions. For that, hydrogels of PVP/agar/PEG, PVP/agar/glycerol and without agar or plasticizer were simultaneously synthesized and sterilized by irradiation of mixtures of such products in aqueous solutions, using gamma-rays from 60 Co source at a dose of 25 kGy. The results based on gel fraction, swelling in water, and some mechanical tests suggest that the degree of PVP cross-linking prevailed over the greater hydrophilicity of glycerol compared to that of PEG with regard to the degree of swelling of the hydrogels. (author)

Novel fluorescent poly(glycidyl methacrylate) - silica microspheres

Czech Academy of Sciences Publication Activity Database

Grama, Silvia; Boiko, N.; Bilyy, R.; Klyuchivska, O.; Antonyuk, V.; Stoika, R.; Horák, Daniel

2014-01-01

Roč. 56, July (2014), s. 92-104 ISSN 0014-3057 R&D Projects: GA MŠk EE2.3.30.0029; GA MŠk(CZ) ED1.1.00/02.0109 Institutional support: RVO:61389013 Keywords : microspheres * silica * poly(glycidyl methacrylate) Subject RIV: CE - Biochemistry Impact factor: 3.005, year: 2014

Process for producing a coating composition. [electron beam irradiation

Energy Technology Data Exchange (ETDEWEB)

Kimura, T; Harada, H; Kobayashi, S; Nakamoto, H; Sunano, K

1968-07-19

An easily hardenable acrylic coating composition is produced by irradiation with low energy electron beams to economize the industrial application of the composition. A polymer with molecular weights in the 5,000 to 500,000 range is composed of 1 to 40% by weight of a vinyl monomer containing a glycidyl radical, 30 to 99% of a methacrylic monomer and 0 to 69% of other copolymerizable vinyl monomers. This polymer dissolves in a monomer containing at least 30% of an acrylic monomer and 70% of other vinyl monomers. The reaction takes place between 0.1 to 1.0 mole of vinyl monomer containing a carboxyl radical and one mole of glycidyl radical in the solution. In an embodiment, 17.5% by weight of glycidyl methacrylate and 82.5% of alkyl acrylate are polymerized in suspension in the presence of a catalyst to form a bead like polymer with molecular weights in the 5,000 to 500,000 range. After 120 parts of the bead like polymer are dissolved in 180 parts of the acrylic monomer in the presence of a polymerization inhibitor by heating, 22 parts of ..cap alpha.., ..beta..- unsaturated monocarboxylic acid are added to the solution to react with the glycidyl radical, whereby a non-solvent type coating material containing the polymer having a vinyl radical side chain is produced. In the place of the catalyst, electron beams can be used at an energy level of 0.1 to 20 MeV. The dose rate may be in the range of 0.1 to 2.0 Mrad/sec.

Magnetic poly(glycidyl methacrylate) particles prepared in the presence of surface-modified .gamma.-Fe2O3

Czech Academy of Sciences Publication Activity Database

Tocchio, A.; Horák, Daniel; Babič, Michal; Trchová, Miroslava; Veverka, Miroslav; Beneš, Milan J.; Šlouf, Miroslav; Fojtík, A.

2009-01-01

Roč. 47, č. 19 (2009), s. 4982-4994 ISSN 0887-624X R&D Projects: GA AV ČR(CZ) KAN401220801; GA ČR GA203/09/1242; GA ČR GA203/09/0857 Institutional research plan: CEZ:AV0Z40500505; CEZ:AV0Z10100521 Keywords : coatings * core - shell polymers * glycidyl methacrylate Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.971, year: 2009

A study on poly (N-vinyl-2-pyrrolidone covalently bonded NiTi surface for inhibiting protein adsorption

Directory of Open Access Journals (Sweden)

Hongyan Yu

2016-12-01

Full Text Available Near equiatomic NiTi alloys have been extensively applied as biomaterials owing to its unique shape memory effect, superelasticity and biocompatibility. It has been demonstrated that surfaces capable of preventing plasma protein adsorption could reduce the reactivity of biomaterials with human blood. This motivated a lot of researches on the surface modification of NiTi alloy. In the present work, following heat and alkaline treatment and silanization by trichlorovinylsilane (TCVS, coating of poly (N-vinyl-2-pyrrolidone (PVP was produced on the NiTi alloy by gamma ray induced chemical bonding. The structures and properties of modified NiTi were characterized and in vitro biocompatibility of plasma protein adsorption was investigated. The results indicated that heat treatment at 823 K for 1 h could result in the formation of a protective TiO2 layer with “Ni-free” zone on NiTi surface. It was found that PVP was covalently bonded on NiTi surface to create a hydrophilic layer for inhibiting protein adsorption on the surface. The present work offers a green approach to introduce a bioorganic surface on metal and other polymeric or inorganic substrates by gamma irradiation.

Process for a preparing a coating composition. [electrom irradiation

Energy Technology Data Exchange (ETDEWEB)

Kimura, T; Harada, H; Kobayashi, J; Nakamoto, H; Sunano, K

1968-07-16

An easily hardenable acrylic coating composition is prepared with low energy electron beams to develop a surface coating process without requiring solvents, and which may be widely applied by industry. The process comprises dissolving a polymer with a molecular weight in the 5,000 to 500,000 range in a monomer consisting of at least 30% by weight of acrylic monomer and 70% by weight of other vinyl monomers. The polymer is obtained by the polymerization of 1 to 40% by weight of vinyl monomer containing carboxyl radicals, 30 to 99% by weight of methacrylic monomer and 0 to 69% by weight of other copolymerizable vinyl monomers. Then, one mole of carboxyl radical of the solution reacts with 0.1 to 1.0 mole of vinyl monomer containing a glycidyl radical. In an embodiment, 17.5% by weight of methacrylate are dissolved in 82.5% of alkyl acrylate and undergo suspension polymerization in water in the presence of a catalyst to produce a beads-like polymer of molecular weight in the 5,000 to 500,000 range. Thereafter, 120 parts of the beads-like polymer are dissolved in 180 parts of acrylic monomer in the presence of a polymerization inhibitor. To this solution are added 22 parts of glycidyl methacrylate to react with carboxyl radicals, thereby obtaining non-solvent coating materials which contain the side chain vinyl radicals in the polymer. The acceleration voltage of the electron beams employed in the polymerization is generally 0.1 to 2.0 MeV. The dose rate to harden the coatings is in the range of 0.1 to 2.0 Mrad/sec.

Chemical Modification of Radiation Copolymerized of [N-Vinyl-2-Pyrrolidone/2-(4-Methoxy-Benzylidine)-Malononitrile] with Some Organic Compounds and Their Biological Activity

International Nuclear Information System (INIS)

El Sawy, N.M.; Mostafa, T.B.

2012-01-01

N-Vinyl-2-Pyrrolidone (NVP) was copolymerized with 2-(4-methoxy benzylidine)-malononitrile (MBM) monomers to form a new copolymer, P(MBM-co-NVP), containing nitrile groups. The characterization of copolymer and their modified with organic compounds such as thiourea, thiosemicarbazide,2-aminothiazole, N-Glycyl glycine, 4-amino-N-[5-methyl-3-isoxazolyl]benzene sulfonamide and 4-amino-N-[4-methyl-2-pyrimidnyl]benzene sulfonamide was carried out by Fourier transform infrared spectroscopy (FTIR), Elemental analysis (EA), Gel Permeation Chromatograph (GPC), Differential Scanning Calorimetry (DSC) and Thermal Gravimetric analysis (TGA). The changes in surface morphology of the prepared copolymer and its modified copolymers were observed by scanning electron microscopy (SEM). The biological activity of the modified copolymers with some organic compounds containing with or without sulfur was investigated. The results revealed that the biological activity of the modified copolymers was higher than that of the copolymer ones, under the same conditions. An improvement of prepared copolymers by modification with various organic compounds showed great promise in some practical applications in the field of antibacterial activity.

Microencapsulation of Epoxidized Linseed Oil Liquid Cross-Linker in Poly(N-vinyl-pyrrolidone): Optimization by a Design-of-Experiments Approach

NARCIS (Netherlands)

Senatore, D.; Laven, J.; Benthem, van R.A.T.M.; La Camera, D.; With, de G.

2010-01-01

A liquid cross-linker, epoxidized linseed oil (ELO), was encapsulated in a plastic with a high glass transition temperature (poly(N-vinyl-2-pyrrolidone); PVP). The process parameters of the spray-drying employed were optimized by a Design-of-Experiments (DoE) approach. Three factors concerning both

Magnetic poly(glycidyl methacrylate) microspheres for protein capture

Czech Academy of Sciences Publication Activity Database

Koubková, Jana; Müller, P.; Hlídková, Helena; Plichta, Zdeněk; Proks, Vladimír; Vojtěšek, B.; Horák, Daniel

2014-01-01

Roč. 31, č. 5 (2014), s. 482-491 ISSN 1871-6784 R&D Projects: GA ČR GCP207/12/J013; GA MŠk 7E12053 EU Projects: European Commission(XE) 246513 - NADINE Institutional support: RVO:61389013 Keywords : glycidyl methacrylate * microspheres * protein p53 Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.898, year: 2014

The Impact of the Polymer Chain Length on the Catalytic Activity of Poly(N-vinyl-2-pyrrolidone)-supported Gold Nanoclusters

OpenAIRE

Haesuwannakij, Setsiri; Kimura, Tetsunari; Furutani, Yuji; Okumura, Kazu; Kokubo, Ken; Sakata, Takao; Yasuda, Hidehiro; Yakiyama, Yumi; Sakurai, Hidehiro

2017-01-01

Poly(N-vinyl-2-pyrrolidone) (PVP) of varying molecular weight (M w ?=?40-360?kDa) were employed to stabilize gold nanoclusters of varying size. The resulting Au:PVP clusters were subsequently used as catalysts for a kinetic study on the sized-dependent aerobic oxidation of 1-indanol, which was monitored by time-resolved in situ infrared spectroscopy. The obtained results suggest that the catalytic behaviour is intimately correlated to the size of the clusters, which in turn depends on the mol...

Graft copolymerization of N-vinyl-2-pyrrolidone onto pre-irradiated poly(vinylidene fluoride) powder

International Nuclear Information System (INIS)

Xu Chenqi; Huang Wei; Zhou Yongfeng; Yan Deyue; Chen Shutao; Huang Hua

2012-01-01

Graft copolymerization of N-vinyl-2-pyrrolidone (NVP) onto 60 Co γ-ray pre-irradiated poly (vinylidene fluoride) (PVDF) powder was investigated to find out the relationship between the degree of grafting (DG) and various factors, including monomer concentration, irradiation dose, reaction time, catalyst and so on. The DG can be calculated by comparing the amount of nitrogen element in the resulting copolymer (PVDF-g-PVP) powder with that in PVP on the basis of element analysis. The presence of PVP in the resulting PVDF powder was confirmed by the comparative studies of pristine PVDF and grafted PVDF powder through Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), thermo gravimetric analyzer (TGA) and differential scanning calorimetry (DSC), respectively. When the reaction was performed at the monomer concentration of 20% (vol.) and the absorbed dose of 40 kGy for 3 h in water, the max. DG of 17.7% was obtained. - Highlights: ► We modify pristine PVDF powders with NVP by the pre-irradiated graft polymerization. ► The various factors influencing the degree of grafting are investigated in detail. ► The optimal condition of graft polymerization is obtained. ► The polymerization is processed at 20% (vol.) of NVP and 40kGy for 3 hours in water. ► The maximum degree of grafting is 17.7 % at such a condition.

Adsorption of {alpha}-amylase onto poly(N-vinyl 2-pyrrolidone/itaconic acid) hydrogels

Energy Technology Data Exchange (ETDEWEB)

Tuemtuerk, Hayrettin; Caykara, Tuncer; Kantoglu, Oemer; Gueven, Olgun

1999-05-02

{alpha}-Amylase enzyme was adsorbed on poly(N-vinyl 2-pyrrolidone/itaconic acid) (P(VP/IA)) hydrogels prepared by irradiating the ternary mixtures of VP/IA/water by {gamma}-rays at ambient temperature. The adsorption capacity of the hydrogels was determined to increase from 2.30 to 3.40 mg {alpha}-amylase/g dry gel with increasing amount of IA in gel system. Kinetic parameters were calculated as 2.51 g/dm{sup 3} for K{sub m} and 1.67x10{sup -3} g/dm{sup 3} min for V{sub max} for free enzyme and in the range of 3.88-5.02 g/dm{sup 3} for K{sub m} and 1.62x10{sup -3}-2.27 x 10{sup -3} g/dm{sup 3} min for V{sub max} depending on the amount of IA in the hydrogel. Enzyme activities were found to increase from 49.9% to 77.4% with increasing amount of IA in the gel system and retained their activities for one month storage. On the other hand, the free enzyme loses its activity completely after 20 days.

Synthesis Of Copoly (2-Hydroxy Ethyl Methacrylate/N-Vinyl Pirrolidone) Hydrogel By Gamma Irradiation And Immobilization Of Ametryne

International Nuclear Information System (INIS)

Erizal

2002-01-01

The synthesis of copoly (2-hydroxy ethyl methacrylate/N-vinyl pirrolidone) hydrogel has been carried out. The 2-hydroxy ethyl methacrylate (HEMA) solution with the concentrations of 40, 50, and 60 % v/v were respectively mixed with N-vinyl pirrolidone (NVP) at a concentration of 5 % v/v with composition of 4:1, homogenized, and bubbled with N 2 .The samples were irradiated by gamma rays at a doses of 5 kGy (dose rate 7.5 kGy/h). The parameters were observed the effect of time soaking (0-32 hours) and temperatures (10-60 oC ) of the hydrogels, the ability of hydrogels to absorb water, the ability of hydrogels for immobilization and released of ametryne and its effects on the kiambang growth. After evaluation, with increasing the concentration of HEMA ( NVP constant), the water absorption and the amount of ametryne released decreased, relatively. With increasing the temperature up to 60 oC and the concentrations of HEMA, the water absorption decreased. The amount of ametryne released from hydrogel affect the growth of kiambang

40 CFR 180.1130 - N-(n-octyl)-2-pyrrolidone and N-(n-dodecyl)-2-pyrrolidone; exemptions from the requirement of a...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false N-(n-octyl)-2-pyrrolidone and N-(n... EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Exemptions From Tolerances § 180.1130 N-(n-octyl)-2-pyrrolidone and N-(n-dodecyl)-2-pyrrolidone; exemptions from the requirement of a tolerance. N-(n-octyl)-2...

Radiation synthesis and characterization of pH-sensitive poly(acrylic acid-co-N-vinyl-2-pyrrolidone) hydrogels

International Nuclear Information System (INIS)

Yang Mingcheng; Zhu Jun; Song Weidong; Song Hongyan; Zhu Chengshen

2006-01-01

Hydrogels are crosslinked, three-dimensional hydrophilic polymer networks that swell but do not dissolve when brought into contact with water. These materials have been investigated extensively for potential applications in the biomedical field because of their similarities to soft tissues and their good tissue and blood compatibility. More specifically, pH-sensitive hydrogels are used for sustained gastro-intestinal drug delivery systems due to the intimacy and extended duration of contact. In this work, pH-sensitive copolymer hydrogels were prepared using acrylic acid and N-vinyl-2-pyrrolidone by γ-ray irradiation at ambient temperature. Effects of dose, monomer concentration, monomer composition, temperature and pH on the swelling ratio (SR) of the copolymer hydrogels were investigated in detail. The results show that SR of the copolymer hydrogels decreases with the monomer concentration and with the increase of absorbed dose. These copolymer hydrogels show good pH-sensitive behavior. These material shows no noticeable change in swelling at lower pH (pH<4) but an abrupt increase in swelling at higher pH (from pH7 to pH9.8). At pH 1.4, the SR of the copolymer hydrogels increases with the temperature. To the contrary, at pH 9.8, the SR of the copolymer hydrogels decreases with the temperature. (authors)

Laser induced augmentation of silver nanospheres to nanowires in ethanol fostered by Poly Vinyl Pyrrolidone

Energy Technology Data Exchange (ETDEWEB)

Sebastian, Suneetha, E-mail: sunikutty@gmail.com; Linslal, C.L.; Vallabhan, C.P.G.; Nampoori, V.P.N.; Radhakrishnan, P.; Kailasnath, M.

2014-11-30

Highlights: • Silver nanospheres are synthesised in ethanol containing Poly Vinyl Pyrrolidone which acts as a polymeric capping agent to nanoparticles thus improving its stability. • Laser irradiation onto the colloidal solution of silver nanoparticles produced well defined nanowires through ripening mechanism promoted by Poly Vinyl Pyrrolidone. • Nanowires so formed are having an average length of 8.7 μm and width of 160 nm. - Abstract: Stable uniform silver nanospheres having an average diameter of 45 nm are synthesised in ethanol containing Poly Vinyl Pyrrolidone using Laser Ablation in Liquid technique. Further irradiation of the nanocolloidal solution by focussed laser beam produced stable well defined silver nanowires through ripening mechanism fostered by the presence of Poly Vinyl Pyrrolidone. Confirmation of the mechanism is obtained from Transmission Electron Microscopic images of the nanocolloidal solution irradiated for different time durations.

Poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate)/clay composites

International Nuclear Information System (INIS)

Marinovic, S.; Vukovic, Z.; Nastasovic, A.; Milutinovic-Nikolic, A.; Jovanovic, D.

2011-01-01

Highlights: → We synthesized macroporous composites of poly(GMA-co-EGDMA) and either raw or acid modified clay. → Morphological, textural and thermal properties of the composite with acid modified clay were significantly changed with retained macroporosity. → Composite with raw clay has enhanced thermal stability. - Abstract: In this study, macroporous composites of poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) i.e. poly(GMA-co-EGDMA) and clay were prepared by radical suspension copolymerization. The composites with either raw (S 0 ) or acid-modified clay (S A ) were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric (TG) and textural analysis. The morphological, textural and thermal properties of the composite with raw clay (CP-S 0 ) differed slightly from those of the copolymer (CP), with exception of the thermal stability expressed in the shifting of the initial degradation temperature from 125 deg. C for CP to 210 deg. C for CP-S 0 . On the other hand, composite with modified clay (CP-S A ) was a material with significantly changed morphology, porous structure parameters and a qualitatively different thermal behavior in comparison to CP and CP-S 0 . CP-S A had mass residue, after heating at 600 deg. C, three times higher than the amount of S A introduced into the reaction system. This indicates a different manner of incorporation of S A , compared to S 0 , into the composite. Both the obtained composites retained their macroporosity and might be used in all applications that involve macroporous copolymers and, due to the altered thermal properties, their application may be extended.

Preparation of unsaturated acrylic prepolymer and electron beam curing of its mixture with vinyl monomers

International Nuclear Information System (INIS)

Pyun, H.C.; Park, W.B.; Kim, K.Y.; Sung, K.Y.

1980-01-01

Electron beam curable prepolymers were prepared by the addition reaction of methyl methacrylate-glycidyl methacrylate copolymer with methacrylic acid, and electron beam curing was studied for the prepolymer and their mixtures of several kind of vinyl monomers. When the reaction was carried out in the presence of triethylbenzyl ammonium chloride in N,N-dimethyl formamide solution, the rate of addition reaction obeyed first-order kinetics. In the electron beam curing, the rate of gel formation of the prepolymer was slower than that of the mixtures of prepolymer and monomers. In the curing of mixtures of prepolymer with polyethyleneglycol dimethacrylates, the rate of gel formation increased with the increase in the degree of polymerization of polyethylene oxide fraction of polyethyleneglycol dimethacrylate, and decreased with the increase the polyethyleneglycol dimethacrylate content. The properties of cured coatings were also examined. (author)

Synthesis of PbS/poly (vinyl-pyrrolidone) nanocomposite

International Nuclear Information System (INIS)

Patel, Jayesh D.; Chaudhuri, Tapas K.

2009-01-01

A simple solution growth method for synthesis of nanocomposite of PbS nanoparticles in poly(vinyl-pyrrolidone) (PVP) polymer is described. The nanocomposite is prepared from methanolic solution of lead acetate (PbAc), thiourea (TU) and PVP at room temperature (∼27 deg. C). Optical absorption spectrum of PbS/PVP nanocomposite solution shows strong absorption from 300 to 650 nm with significant bands at 400 and 590 nm which is characteristic of nanoscale PbS. Spin-coated nanocomposite films on glass have an absorption edge at ∼650 nm with band gap of 2.55 eV. Fourier transform infrared (FTIR) spectroscopy of PbS/PVP nanocomposite and PVP shows strong chemical bond between PbS nanoparticles and host PVP polymer. The transmission electron microscope (TEM) images reveal that 5-10 nm PbS particles are evenly embedded in PVP polymer. The formation of PbS is confirmed by selective area electron diffraction (SAED) of a typical nanoparticle.

Structural and optical characteristics of silver/poly(N-vinyl-2-pyrrolidone) nanosystems synthesized by γ-irradiation

International Nuclear Information System (INIS)

Jovanović, Željka; Radosavljević, Aleksandra; Šiljegović, Milorad; Bibić, Nataša; Mišković-Stanković, Vesna; Kačarević-Popović, Zorica

2012-01-01

Silver nanoparticles (AgNPs) were synthesized in situ by γ-irradiation using poly(N-vinyl-2-pyrrolidone) (PVP) as a capping agent. The concentration, molecular weight and the structure (crosslinked and interpenetrated network) of PVP were varied, in order to determine the influence of the capping agent in the radiolytic synthesis of the Ag/PVP nanosystems. Transmission electron microscopy (TEM) showed that AgNPs obtained from the solutions containing higher PVP concentration and higher molecular weight were spherical in shape, with narrow size distribution and a diameter of∼6 nm, while slightly larger rod-shaped silver agglomerates, with bimodal nanoparticle size distribution and diameters of ∼10 nm and ∼20 nm were obtained from the solutions containing lower PVP concentration and lower molecular weight. Strong plasmon coupling and extending of plasmon resonance was observed by UV–vis spectroscopy, as a result of formation of nanorod-like agglomerates. Crosslinked and interpenetrated network did not affect the structure of synthesized AgNPs. Ag/PVP nanocomposite, in the form of thin film, was obtained by solvent evaporation from Ag/PVP colloid solution with 10 wt% of PVP, and characterized by FTIR spectroscopy. The interactions in Ag/PVP nanocomposite are shown to be the result of the coordination bonding between AgNPs and nitrogen from pyrrolidone ring of PVP. The optical properties of investigated Ag/PVP nanosystems, as measured by the values of optical band gap, E g , are mainly the consequence of the interparticle distance as a result of the concentration and the structure of surrounding PVP macromolecules. - Highlights: ► AgNPs of different structure and optical properties were obtained by γ-irradiation. ► Different PVP concentration and molecular weight induced different structure. ► Rod-shaped AgNPs were obtained with lower PVP concentration and molecular weight. ► Stabilization by coordination bonding between AgNPs and N from pyrrolidone

Poly(glycidyl methacrylate)-A soft template for the facile preparation of poly(glycidyl methacrylate) core-copper nanoparticle shell nanocomposite

Science.gov (United States)

Mohammed Safiullah, S.; Abdul Wasi, K.; Anver Basha, K.

2015-12-01

Poly(glycidyl methacrylate) core/copper nanoparticle shell nanocomposite (PGMA/Cu nanohybrid) was prepared by simple two step method (i) The synthesis of poly(glycidyl methacrylate) (PGMA) beads by free radical suspension polymerization followed by (ii) direct deposition of copper nanoparticles (CuNPs) on activated PGMA beads. The PGMA beads were used as a soft template to host the CuNPs without surface modification of it. In this method the CuNPs were formed by chemical reduction of copper salts using sodium borohydride in water medium and deposited directly on the activated PGMA. Two different concentrations of copper salts were employed to know the effect of concentration on the shape and size of nanoparticles. The results showed that, the different sizes and shapes of CuNPs were deposited on the PGMA matrix. The X-ray Diffraction study results showed that the CuNPs were embedded on the surface of the PGMA matrix. The scanning electron microscopic images revealed that the fabrication of CuNPs on the PGMA matrix possess different shapes and changes the morphology and nature of PGMA beads significantly. The fluorescent micrograph also confirmed that the CuNPs were doped on the PGMA surface. The thermal studies have demonstrated that the CuNPs deposition on the surface of PGMA beads had a significant effect.

Preparation and characterization of poly(glycidyl methacrylate) grafted from magnesium hydroxide particles via SI-ATRP

International Nuclear Information System (INIS)

Liu Jianhui; Feng Na; Chang Suqin; Kang Hongliang

2012-01-01

In order to improve the compatibility of magnesium hydroxide particles [Mg(OH) 2 ] and polymer matrix, poly(glycidyl methacrylate) (PGMA) grafted from magnesium hydroxide particles were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP). In this work, two approaches for the immobilization of ATRP initiator on the magnesium hydroxide particles surface were compared and selected. The density of initiator was significantly increased by the method of introducing more hydroxyl groups via ATRP of 2-hydroxyethyl methacrylate (HEMA) on the surface. The percentage of bromine atom for the initiator-functionalized magnesium hydroxide particles [Mg(OH) 2 -g-PHEMA-Br] reached to 1.75%, compared to 0.48% for Mg(OH) 2 -Br determined by XPS analysis. The surface-initiated ATRP of glycidyl methacrylate (GMA) can be conducted in a controlled manner, as revealed by the linear kinetic plot, linear increase of number average molecular weight (M n ) with monomer conversions, and the relatively narrow molecular weight distributions (M w /M n ∼ 1.4) of PGMA chains. The percentage of grafting PG (%) and the thickness of the grafted polymer layer increased with the increasing of polymerization time and reached to 116.6% and 197.6 nm after 300 min respectively. As for the polymerization with different initial monomer concentration, the number average molecular weights (M n ) and weight average molecular weights (M w ) of PGMA increased with the increasing of initial monomer concentration. TGA indicated that the initial decomposition temperature of Mg(OH) 2 -g-PHEMA-PGMA composite particles (253 °C) was much lower than that of unmodified magnesium hydroxide particles (337 °C).

Preparation and characterization of poly(glycidyl methacrylate) grafted from magnesium hydroxide particles via SI-ATRP

Energy Technology Data Exchange (ETDEWEB)

Liu Jianhui [School of Textile and Materials Engineering, Dalian Polytechnic University, Dalian 116034 (China); Feng Na, E-mail: fengna12@163.com [School of Textile and Materials Engineering, Dalian Polytechnic University, Dalian 116034 (China); Chang Suqin [China Leather and Footwear Industry Research Institute, Beijing 100015 (China); Kang Hongliang [State Key Laboratory of Polymer Physics and Chemistry, Joint Laboratory of Polymer Science and Material, Beijing National Laboratory for Molecular Sciences (BNLMS), Institute of Chemistry, Chinese Academy of Sciences, Beijing 100080 (China)

2012-06-01

In order to improve the compatibility of magnesium hydroxide particles [Mg(OH){sub 2}] and polymer matrix, poly(glycidyl methacrylate) (PGMA) grafted from magnesium hydroxide particles were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP). In this work, two approaches for the immobilization of ATRP initiator on the magnesium hydroxide particles surface were compared and selected. The density of initiator was significantly increased by the method of introducing more hydroxyl groups via ATRP of 2-hydroxyethyl methacrylate (HEMA) on the surface. The percentage of bromine atom for the initiator-functionalized magnesium hydroxide particles [Mg(OH){sub 2}-g-PHEMA-Br] reached to 1.75%, compared to 0.48% for Mg(OH){sub 2}-Br determined by XPS analysis. The surface-initiated ATRP of glycidyl methacrylate (GMA) can be conducted in a controlled manner, as revealed by the linear kinetic plot, linear increase of number average molecular weight (M{sub n}) with monomer conversions, and the relatively narrow molecular weight distributions (M{sub w}/M{sub n} {approx} 1.4) of PGMA chains. The percentage of grafting PG (%) and the thickness of the grafted polymer layer increased with the increasing of polymerization time and reached to 116.6% and 197.6 nm after 300 min respectively. As for the polymerization with different initial monomer concentration, the number average molecular weights (M{sub n}) and weight average molecular weights (M{sub w}) of PGMA increased with the increasing of initial monomer concentration. TGA indicated that the initial decomposition temperature of Mg(OH){sub 2}-g-PHEMA-PGMA composite particles (253 Degree-Sign C) was much lower than that of unmodified magnesium hydroxide particles (337 Degree-Sign C).

Modification of polyethylene films by radiation grafting of glycidyl methacrylate and immobilization of {beta}-cyclodextrin

Energy Technology Data Exchange (ETDEWEB)

Nava-Ortiz, C.A.B. [Departamento de Quimica de Radiaciones y Radioquimica, Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Circuito Exterior, Ciudad Universitaria, Mexico DF 04510 (Mexico); Burillo, G. [Departamento de Quimica de Radiaciones y Radioquimica, Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Circuito Exterior, Ciudad Universitaria, Mexico DF 04510 (Mexico)], E-mail: burillo@nucleares.unam.mx; Bucio, E. [Departamento de Quimica de Radiaciones y Radioquimica, Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Circuito Exterior, Ciudad Universitaria, Mexico DF 04510 (Mexico); Alvarez-Lorenzo, C. [Departamento de Farmacia y Tecnologia Farmaceutica, Facultad de Farmacia, Universidad de Santiago de Compostela, 15782 Santiago de Compostela (Spain)

2009-01-15

Glycidyl methacrylate was grafted onto polyethylene films using a preirradiation method with {gamma} rays. The effect of absorbed dose, monomer concentration, and reaction time on the degree of grafting was determined. The grafted samples were verified by FTIR-ATR spectroscopy. {beta}-Cyclodextrin was immobilized onto polypropylene modified with glycidyl methacrylate, and the ability of the cavities of {beta}-cyclodextrin to form inclusion complexes was demonstrated using the typically organic compound approach with m-toluic acid (3-MBA) as a probe.

Iodinated glycidyl methacrylate copolymer as a radiopaque material for biomedical applications.

Science.gov (United States)

Dawlee, S; Jayabalan, M

2013-07-01

Polymeric biomaterial was synthesized by copolymerizing 50:50 mol% of monomers, glycidyl methacrylate and methyl methacrylate. Iodine atoms were then grafted to the epoxide groups of glycidyl methacrylate units, rendering the copolymer radiopaque. The percentage weight of iodine in the present copolymer was found to be as high as 23%. The iodinated copolymer showed higher glass transition temperature and thermal stability in comparison with unmodified polymer. Radiographic analysis showed that the copolymer possessed excellent radiopacity. The iodinated copolymer was cytocompatible to L929 mouse fibroblast cells. The in vivo toxicological evaluation by intracutaneous reactivity test of the copolymer extracts has revealed that the material was nontoxic. Subcutaneous implantation of iodinated copolymer in rats has shown that the material was well tolerated. Upon explantation and histological examination, no hemorrhage, infection or necrosis was observed. The samples were found to be surrounded by a vascularized capsule consisting of connective tissue cells. The results indicate that the iodinated copolymer is biocompatible and may have suitable applications as implantable materials.

ANIONIC POLYMERIZATION OF ALKYL METHACRYLATES INITIATED BY nBuCu(NCy2)Li

Institute of Scientific and Technical Information of China (English)

Bing-yong Han; Jian-guo Liang; Jian-min Lu; Feng An; Wan-tai Yang

2009-01-01

Anionic polymerization of methyl methacrylate (MMA), n-butyl methacrylate (nBMA) and glycidyl methacrylate (GMA) initiated by nBuCu(NCy2)Li (1) in tetrahydrofuran (THF) at -50℃ to -10℃ was investigated. It was found that the polymerization of MMA and nBMA initiated by 1 proceeded quantitatively in THF to afford PMMA and PBMA with polydispersity index 1.15-1.30 and nearly 100% initiator efficiencies at -10℃. The molecular weights increased linearly with the ratio of [monomer]/[1]. However, a post-polymerization experiment carried out on this system revealed a double polymer peak by GPC when fresh monomer was added after an interval of 10 rain. Polymerization of styrene could be initiated by 1, but the initiator efficiency was low.

Novel coating compositions

International Nuclear Information System (INIS)

Kimura, Tadashi; Kobayashi, Juichi; Nakamoto, Hideo.

1969-01-01

An acrylic coating composition rapidly hardenable by irradiating with ionizing radiations or light beams is given using hydroxyl group-containing vinyl monomers, polycarboxylic acid anhydrides, epoxy group-containing vinyl monomers and an organic solvent having a boiling point of at least 120 0 C. The process comprises the steps of first and second reactions. The first reaction takes place between one mol of a hydroxyl group of a basic polymer and at least 0.1 mol of polycarboxylic acid anhydride, wherein the basic polymer has a molecular weight ranging from 5,000 to 100,000 and consists of 1-40% by weight of vinyl monomer containing hydroxyl group, at least 30% of (meth)acrylic monomer and other vinyl monomers if required. The second reaction takes place between one mol of hydroxyl plus a carboxyl group of the thus obtained basic polymer and at least 0.1 mol of an epoxy group-containing vinyl monomer to produce a prepolymer. The prepolymer is mixed with a solvent such as ethyl benzene to produce the coating material. The electron beam accelerator energy level may be 0.1-2.0 MeV. In light beam polymerization, benzoin is particularly utilized as an intensifying substance. In one example, a basic polymer is produced by reacting 39 parts of styrene, 37 parts of ethyl acrylate, 24 parts of 2-hydroxyl ethyl acrylate, 4 parts of dimethyl amino ethyl methacrylate and others. A prepolymer is produced by reacting this basic polymer with 30 parts of glycidyl acrylate and others. (Iwakiri, K.)

Radiation-chemical preparation of poly(vinyl alcohol) hydrogels

International Nuclear Information System (INIS)

Duflot, Anastasia V.; Kitaeva, Natalia K.; Duflot, Vladimir R.

2015-01-01

This work reports the usage of method of radiation-chemical synthesis to prepare cross-linked hydrogels from poly(vinyl alcohol) modified with glycidyl methacrylate. Synthesis kinetics of modified poly(vinyl alcohol) and properties of hydrogels were studied. The gel fraction, swelling, mechanical properties, and water content of the hydrogels were measured. It was found that gel fraction increases with increasing radiation dose, concentration of modified poly(vinyl alcohol), and reaches 60%. It was established by differential scanning calorimetry that a fraction of the “bound” water in hydrogels is 50–70% and independent of gel fraction content. In addition to “bound” and “free” states, water in hydrogels is also present in the intermediate state. - Highlights: • The synthesis and the properties of poly(vinyl alcohol) hydrogels were studied. • PVA was modified by glycidyl methacrylate before gamma cross-linking. • The modification results in decreasing of PVA cross-linking dose by 3 orders lower. • The gel fraction and water content of the hydrogels were measured. • A fraction of the “bound” water in hydrogels is independent of gel fraction content

Antifouling peptide dendrimer surface of monodisperse magnetic poly(glycidyl methacrylate) microspheres

Czech Academy of Sciences Publication Activity Database

Hlídková, Helena; Kotelnikov, Ilya; Pop-Georgievski, Ognen; Proks, Vladimír; Horák, Daniel

2017-01-01

Roč. 50, č. 4 (2017), s. 1302-1311 ISSN 0024-9297 R&D Projects: GA ČR(CZ) GC16-01128J; GA ČR(CZ) GA16-02702S; GA ČR(CZ) GJ15-09368Y Grant - others:OPPK(XE) CZ.2.16/3.1.00/21545 Program:OPPK Institutional support: RVO:61389013 Keywords : poly(glycidyl methacrylate) * magnetic microspheres * peptides Subject RIV: CD - Macromolecular Chemistry OBOR OECD: Polymer science Impact factor: 5.835, year: 2016

Studies on novel radiopaque methyl methacrylate: glycidyl methacrylate based polymer for biomedical applications.

Science.gov (United States)

Dawlee, S; Jayakrishnan, A; Jayabalan, M

2009-12-01

A new class of radiopaque copolymer using methyl methacrylate (MMA) and glycidyl methacrylate (GMA) monomers was synthesized and characterized. The copolymer was made radiopaque by the epoxide ring opening of GMA using the catalyst o-phenylenediamine and the subsequent covalent attachment of elemental iodine. The copolymer was characterized by Fourier transform infrared (FTIR) spectra, energy dispersive X-ray analysis using environmental scanning electron microscope (EDAX), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). X-ray visibility of the copolymer was checked by X-radiography. Blood compatibility and cytotoxicity of the newly synthesized copolymer were also evaluated. The iodinated copolymer was thermally stable, blood compatible, non-cytotoxic, and highly radiopaque. The presence of bulky iodine group created a new copolymer with modified properties for potential use in biomedical applications.

Hydrogel coating of RVNRL film by electron beam irradiation

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Hj, Mohd Dahlan; Fumio Yoshii; Keizo Makuuchi

1996-01-01

The tackiness properties of Radiation Vulcanized Natural Rubber Latex (RVNRL) film surfaces coated by various monomers have been investigated in order to understand the suitable hydrogels which reduce the tackiness of the film. In this context , different types of monomers namely, N-vinyl-2-pyrrolidone (NVP), N,N-dimethyl amino ethyl amide (DMAEA), acrylic acid (AAc), N-butyl acrylate (n-BA) and 2-hydroxyethyl methacrylate (HEMA) as well as monomer mixtures have been tried with varying degrees of success. It was found that coating the RVNRL with 80% HEMA/20% n-BA by irradiation at 80 kGy using low Energy Electron Beam gave remarkable reduction in surface tackiness of the RVNRL film. Several other attempts were made such as priming with acid and aluminum sulfate, mixing the aluminum sulfate into the monomer and dipping the partially wet RVNRL film into the monomer to enhance the wettability of he monomers with the film. Studies on surface topography revealed that the decrease in tackiness with coating is due to the increase of the surface roughness at 80 kGy, irradiation dose

Influence of gamma irradiation dose and concentration of laponite clay on Poly (N-Vinyl-2-Pyrrolidone) hydrogels

International Nuclear Information System (INIS)

Santos, Vinicius J.; Zafalon, Angélica T.; Lugão, Ademar B.; Parra, Duclerc F.

2017-01-01

Hydrogels are polymeric biomaterials widely used in biomedicine and defined as an insoluble system of one or more crosslinked hydrophilic polymers, capable of absorbing large amounts of fluids without losing their physical integrity. Composed by one three-dimensional network of crosslinked polymer chains they can be synthesized by various physical and chemical methods including radiation. One of these methods is the gamma irradiation process, which forms the crosslinked network and sterilizes the material in a single step. In the biomedical field one of hydrogels applications is the transdermal dressings, these systems have an impact of great value in the treatment of wounds, as they can protect regions injured by burns, cuts and even chronic wounds. The association of clay to hydrogels promotes a modification of properties of these materials, such as swelling and gel fraction. Thus, the objective of this work was to evaluate the swelling properties and gel fraction of hydrogels based on polymer formulation of poly (N-vinyl-2-pyrrolidone), poly (ethylene glycol), agar containing nano-clay laponite RD in Different concentrations (0, 0.01, 0.1, 0.5, 1, 2, 5, 10, 20%). The materials were mixed by stirring and heating and then processed by gamma radiation from Co-60 at doses of 10, 25, 50 and 70 kGy. To evaluate the gel fraction, the membranes were immersed in water for 3 weeks. The swelling was evaluated after 48 hours of immersion in distilled water at room temperature. It was observed that as the clay concentration increases regardless of the irradiation dose the amount of gel fraction decreased and the amount of water absorption increased. (author)

Influence of gamma irradiation dose and concentration of laponite clay on Poly (N-Vinyl-2-Pyrrolidone) hydrogels

Energy Technology Data Exchange (ETDEWEB)

Santos, Vinicius J.; Zafalon, Angélica T.; Lugão, Ademar B.; Parra, Duclerc F., E-mail: vinicius.jusan@gmail.com [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

Hydrogels are polymeric biomaterials widely used in biomedicine and defined as an insoluble system of one or more crosslinked hydrophilic polymers, capable of absorbing large amounts of fluids without losing their physical integrity. Composed by one three-dimensional network of crosslinked polymer chains they can be synthesized by various physical and chemical methods including radiation. One of these methods is the gamma irradiation process, which forms the crosslinked network and sterilizes the material in a single step. In the biomedical field one of hydrogels applications is the transdermal dressings, these systems have an impact of great value in the treatment of wounds, as they can protect regions injured by burns, cuts and even chronic wounds. The association of clay to hydrogels promotes a modification of properties of these materials, such as swelling and gel fraction. Thus, the objective of this work was to evaluate the swelling properties and gel fraction of hydrogels based on polymer formulation of poly (N-vinyl-2-pyrrolidone), poly (ethylene glycol), agar containing nano-clay laponite RD in Different concentrations (0, 0.01, 0.1, 0.5, 1, 2, 5, 10, 20%). The materials were mixed by stirring and heating and then processed by gamma radiation from Co-60 at doses of 10, 25, 50 and 70 kGy. To evaluate the gel fraction, the membranes were immersed in water for 3 weeks. The swelling was evaluated after 48 hours of immersion in distilled water at room temperature. It was observed that as the clay concentration increases regardless of the irradiation dose the amount of gel fraction decreased and the amount of water absorption increased. (author)

Poly(glycidyl methacrylate)—A soft template for the facile preparation of poly(glycidyl methacrylate) core-copper nanoparticle shell nanocomposite

International Nuclear Information System (INIS)

Mohammed Safiullah, S.; Abdul Wasi, K.; Anver Basha, K.

2015-01-01

Graphical abstract: - Highlights: • PGMA/Cu nanohybrids have been synthesized by Surface deposition method. • The CuNPs were deposited on the PGMA surface without surface modification. • CuNP deposition on PGMA has a significant effect on morphology and thermal stability. - Abstract: Poly(glycidyl methacrylate) core/copper nanoparticle shell nanocomposite (PGMA/Cu nanohybrid) was prepared by simple two step method (i) The synthesis of poly(glycidyl methacrylate) (PGMA) beads by free radical suspension polymerization followed by (ii) direct deposition of copper nanoparticles (CuNPs) on activated PGMA beads. The PGMA beads were used as a soft template to host the CuNPs without surface modification of it. In this method the CuNPs were formed by chemical reduction of copper salts using sodium borohydride in water medium and deposited directly on the activated PGMA. Two different concentrations of copper salts were employed to know the effect of concentration on the shape and size of nanoparticles. The results showed that, the different sizes and shapes of CuNPs were deposited on the PGMA matrix. The X-ray Diffraction study results showed that the CuNPs were embedded on the surface of the PGMA matrix. The scanning electron microscopic images revealed that the fabrication of CuNPs on the PGMA matrix possess different shapes and changes the morphology and nature of PGMA beads significantly. The fluorescent micrograph also confirmed that the CuNPs were doped on the PGMA surface. The thermal studies have demonstrated that the CuNPs deposition on the surface of PGMA beads had a significant effect.

Poly(glycidyl methacrylate)—A soft template for the facile preparation of poly(glycidyl methacrylate) core-copper nanoparticle shell nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Mohammed Safiullah, S., E-mail: safichem@gmail.com [Department of Chemistry, C. Abdul Hakeem College of Engineering & Technology, Melvisharam, Vellore District, Tamil Nadu 632509 (India); P.G. & Research Department of Chemistry, C. Abdul Hakeem College, Melvisharam, Vellore District, Tamil Nadu 632509 (India); Abdul Wasi, K. [P.G. & Research Department of Chemistry, C. Abdul Hakeem College, Melvisharam, Vellore District, Tamil Nadu 632509 (India); Anver Basha, K., E-mail: kanverbasha@gmail.com [P.G. & Research Department of Chemistry, C. Abdul Hakeem College, Melvisharam, Vellore District, Tamil Nadu 632509 (India)

2015-12-01

Graphical abstract: - Highlights: • PGMA/Cu nanohybrids have been synthesized by Surface deposition method. • The CuNPs were deposited on the PGMA surface without surface modification. • CuNP deposition on PGMA has a significant effect on morphology and thermal stability. - Abstract: Poly(glycidyl methacrylate) core/copper nanoparticle shell nanocomposite (PGMA/Cu nanohybrid) was prepared by simple two step method (i) The synthesis of poly(glycidyl methacrylate) (PGMA) beads by free radical suspension polymerization followed by (ii) direct deposition of copper nanoparticles (CuNPs) on activated PGMA beads. The PGMA beads were used as a soft template to host the CuNPs without surface modification of it. In this method the CuNPs were formed by chemical reduction of copper salts using sodium borohydride in water medium and deposited directly on the activated PGMA. Two different concentrations of copper salts were employed to know the effect of concentration on the shape and size of nanoparticles. The results showed that, the different sizes and shapes of CuNPs were deposited on the PGMA matrix. The X-ray Diffraction study results showed that the CuNPs were embedded on the surface of the PGMA matrix. The scanning electron microscopic images revealed that the fabrication of CuNPs on the PGMA matrix possess different shapes and changes the morphology and nature of PGMA beads significantly. The fluorescent micrograph also confirmed that the CuNPs were doped on the PGMA surface. The thermal studies have demonstrated that the CuNPs deposition on the surface of PGMA beads had a significant effect.

Magnetic poly(glycidyl methacrylate) microspheres for Campylobacter jejuni detection in food

Czech Academy of Sciences Publication Activity Database

Horák, Daniel; Hochel, I.

061, - (2005), s. 1-12 ISSN 1618-7229 R&D Projects: GA ČR(CZ) GA525/05/0311; GA ČR(CZ) GA525/02/0287 Institutional research plan: CEZ:AV0Z40500505 Keywords : magnetic * microspheres * glycidyl methacrylate Subject RIV: GM - Food Processing Impact factor: 0.926, year: 2005 http://www.e-polymers.org

Study of the structure and parameters of crosslinking of poly(n-vinil-2-pyrrolidone) based hydrophilic membranes induced by radiation

International Nuclear Information System (INIS)

Lopergolo, Lilian Cristine

2002-01-01

A hydrogel is a polymeric material that exhibits the ability to swell in water and retains a significant fraction of water within its structure, but does not dissolve in water. One of the major problems in the application of these materials is their relatively poor mechanical strength, attributed to the high degree of hydration of the gel. This work focused to the study of the interactions between hydrophobic and hydrophilized fibers, with the objective of optimization of the mechanical properties of poly(N-vinyl-2-pyrrolidone) membranes. The membranes were prepared by electron beam irradiation of an aqueous polymer solution. Non-woven polypropylene fiber grafted with methyl methacrylate was employed as reinforcement. Another form of the irradiation was investigated. Ultraviolet radiation was used as an alternative method for the production of PVP membranes. The resulting changes in the main properties of the membranes, such as gel content, swelling characteristics, cytotoxicity , mechanical behavior, crosslinking density, average molecular weight between crosslinks and size pore were investigated. (author)

Magnetic poly(glycidyl methacrylate) microspheres prepared by dispersion polymerization in the presence of electrostatically-stabilized ferrofluids

Czech Academy of Sciences Publication Activity Database

Horák, Daniel; Benedyk, N.

2004-01-01

Roč. 42, č. 22 (2004), s. 5827-5837 ISSN 0887-624X R&D Projects: GA ČR GA525/02/0287 Institutional research plan: CEZ:AV0Z4050913 Keywords : magnetic * glycidyl methacrylate * dispersion polymerization Subject RIV: CE - Biochemistry Impact factor: 2.773, year: 2004

The Impact of the Polymer Chain Length on the Catalytic Activity of Poly(N-vinyl-2-pyrrolidone)-supported Gold Nanoclusters.

Science.gov (United States)

Haesuwannakij, Setsiri; Kimura, Tetsunari; Furutani, Yuji; Okumura, Kazu; Kokubo, Ken; Sakata, Takao; Yasuda, Hidehiro; Yakiyama, Yumi; Sakurai, Hidehiro

2017-08-29

Poly(N-vinyl-2-pyrrolidone) (PVP) of varying molecular weight (M w  = 40-360 kDa) were employed to stabilize gold nanoclusters of varying size. The resulting Au:PVP clusters were subsequently used as catalysts for a kinetic study on the sized-dependent aerobic oxidation of 1-indanol, which was monitored by time-resolved in situ infrared spectroscopy. The obtained results suggest that the catalytic behaviour is intimately correlated to the size of the clusters, which in turn depends on the molecular weight of the PVPs. The highest catalytic activity was observed for clusters with a core size of ~7 nm, and the size of the cluster should increase with the molecular weight of the polymer in order to maintain optimal catalytic activity. Studies on the electronic and colloid structure of these clusters revealed that the negative charge density on the cluster surface also strongly depends on the molecular weight of the stabilizing polymers.

Thionine-modified poly(glycidyl methacrylate) nanospheres as labels of antibodies for biosensing applications

Czech Academy of Sciences Publication Activity Database

Zasońska, Beata Anna; Čadková, M.; Kovářová, A.; Bílková, Z.; Korecká, L.; Horák, Daniel

2015-01-01

Roč. 7, č. 44 (2015), s. 24926-24931 ISSN 1944-8244 R&D Projects: GA MŠk(CZ) ED1.1.00/02.0109 Institutional support: RVO:61389013 Keywords : glycidyl methacrylate * nanospheres * thionine Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 7.145, year: 2015

Coating materials

International Nuclear Information System (INIS)

Ozeki, Takao; Kimura, Tadashi; Kobayashi, Juichi; Maeda, Yutaka; Nakamoto, Hideo.

1969-01-01

A non-solvent type coating material composition having properties as good as thermosetting acrylic or amino alkid resins is provided by employing active energy irradiation, particularly electron beams, using a radically polymerizable low molecular compound (A) (hereafter called an oligomer) containing at least two vinyl radicals in one molecule. This oligomer is produced by reacting an epoxy-containing vinyl monomer with alpha-, beta-ethylene unsaturated carboxylic acids or their anhydrides. The composition (I) contains 10% - 100% of this oligomer. In embodiments, an oligomer having a fiberous trivinyl construction is produced by reacting 180 parts by weight of glycidyl methacrylate ester with 130 parts of itaconic acid in the presence of a polymerization-inhibitor and an addition reaction catalyst at 90 0 C for 6 hours. In practice, the coating material compositions (1), consist of the whole oligomer [I-1]; (2), consist of 10-90% of (A) component and 90%-10% of vinyl monomers containing at least 30% (meth) acrylic monomer [I-2]; (3), 10%-90% of component (A) and 90%-10% of other monomers containing at least two vinyl radicals [I-3]; (4), a mixture of (I-2) and (I-3), [I-4]; and (5), consist of 50% or less unsaturated polyester of 500-5,000 molecular weight range or drying oil, or alkyd resin of 500-5,000 molecular weight range modified by drying oil, [I-5]. As a catalyst a tertiary amino vinyl compound is preferred. Five examples are given. (Iwakiri, K.)

Preliminary studies on 1-vinyl-2-pyrrolidone grafting onto cellulose by pre-irradiation method

Energy Technology Data Exchange (ETDEWEB)

Severich, Patrick; Dutra, Rodrigo da Costa; Kodama, Yasko, E-mail: ykodama@ipen.br, E-mail: patrick.severich@ipen.br, E-mail: rodrigo.dutra@ipen.br [Instituto de Pesquisas Energética s e Nucleares (IPEN-CNEN/SP), São Paulo, SP (Brazil)

2017-07-01

Cellulose is considered a renewable biopolymer most abundant in nature. Better functional surfaces can be Obtained by modifying cellulose. On the other hand, poly vinyl pyrrolidone, PVP, is a synthetic nontoxic, water-soluble polymer frequently used in an extensive variety of applications including several pharmaceutical applications. Grafting 1-vinyl-2-pyrrolidone, NVP, onto polymeric cellulose can be obtained by ionizing radiation. Ionizing radiation grafting can be affected by several factors as environment, solvent, monomer concentration, temperature of graft reaction. Grafting by ionizing radiation can be performed by three methods, pre-irradiation, oxidation by peroxide and simultaneous irradiation. In this study, it was used pre-irradiation method of cellulose. Paper filter without ash, NVP without purification was used in this study. Paper samples were exposed to electron beam from Dynamitron Accelerator with radiation absorbed dose of 25 kGy. Influence of NVP concentration, temperature of reaction after irradiation on degree of grafting (DG) was studied. Also, cellulose radicals of grafted paper samples was studied by electron paramagnetic resonance using a Bruker X-band ESR at room temperature just after heating reaction. Small decrease of cellulose radicals was observed with increasing reaction temperature. It was observed DG small increase with increasing concentration of monomer in solution of water ethanol 50-50 v:v and rising temperature of reaction. Further tests using simultaneous method of grafting of NVP in cellulose paper, in water:ethanol 75:25 v:v solution, induced by gamma irradiation were performed. It was observed homopolymerization forming PVP with increasing monomer concentration. (author)

Preliminary studies on 1-vinyl-2-pyrrolidone grafting onto cellulose by pre-irradiation method

International Nuclear Information System (INIS)

Severich, Patrick; Dutra, Rodrigo da Costa; Kodama, Yasko

2017-01-01

Cellulose is considered a renewable biopolymer most abundant in nature. Better functional surfaces can be Obtained by modifying cellulose. On the other hand, poly vinyl pyrrolidone, PVP, is a synthetic nontoxic, water-soluble polymer frequently used in an extensive variety of applications including several pharmaceutical applications. Grafting 1-vinyl-2-pyrrolidone, NVP, onto polymeric cellulose can be obtained by ionizing radiation. Ionizing radiation grafting can be affected by several factors as environment, solvent, monomer concentration, temperature of graft reaction. Grafting by ionizing radiation can be performed by three methods, pre-irradiation, oxidation by peroxide and simultaneous irradiation. In this study, it was used pre-irradiation method of cellulose. Paper filter without ash, NVP without purification was used in this study. Paper samples were exposed to electron beam from Dynamitron Accelerator with radiation absorbed dose of 25 kGy. Influence of NVP concentration, temperature of reaction after irradiation on degree of grafting (DG) was studied. Also, cellulose radicals of grafted paper samples was studied by electron paramagnetic resonance using a Bruker X-band ESR at room temperature just after heating reaction. Small decrease of cellulose radicals was observed with increasing reaction temperature. It was observed DG small increase with increasing concentration of monomer in solution of water ethanol 50-50 v:v and rising temperature of reaction. Further tests using simultaneous method of grafting of NVP in cellulose paper, in water:ethanol 75:25 v:v solution, induced by gamma irradiation were performed. It was observed homopolymerization forming PVP with increasing monomer concentration. (author)

Acai oil development and evaluation of immobilization and release in poly (N-vinyl-2-pyrrolidone) hydrogels

International Nuclear Information System (INIS)

Machado, Ana Carolina Henriques Ribeiro

2010-01-01

Acai (Euterpe oleracea) is a native palm of Brazil, distributed for the entire Amazonian basin. Rich in essentials fatty acids (mainly oleic acid and linoleic acid), acai oil prevents abnormal conditions of the skin, as dermatitis and drying, and assists in the regeneration of the epidermis. The benefits of the hydrogels are known as dressings. The purpose of this study was to develop devices for controlled release of acai oil on poly (N-vinyl-2-pyrrolidone) (PVP) hydrogels. The behavior of the acai oil front to the radiation was evaluated by the composition of fatty acids of the oil before and after irradiation. Two different matrices of PVP hydrogel were evaluated physically and chemically through assays of swelling, gel fraction, mechanical proprieties and in vitro cytotoxicity. Both matrices were considered adjusted to be used as an active release system. The devices were obtained by acai oil immobilization in PVP hydrogel matrices, were also characterized through assays of sweeling, gel fraction, mechanical proprieties and in vitro cytotoxicity. Moreover, they were characterized by assays of scanning electron microscopy and in vivo primary cutaneous irritation. Both devices were submitted to assay of active release kinetics, and the acai oil was quantified by gas chromatography coupled with mass spectrometry. The devices showed to be satisfactory to compose a release system of actives. (author)

In-situ formation of silver nanoparticles on poly (lactic acid) film by γ-radiation induced grafting of N-vinyl pyrrolidone

Energy Technology Data Exchange (ETDEWEB)

Wang, Jingxia; Chen, Hao; Chen, Zhuping; Chen, Yuheng; Guo, Dan; Ni, Maojun; Liu, Siyang; Peng, Chaorong, E-mail: pengchaorong_siae@163.com

2016-06-01

A fast, easy and novel method for preparing biodegradable polymer films with silver nanoparticles was investigated to endow the material with excellent biocompatibility and antibacterial property. Silver nanoparticles (Ag NPs) were immobilized on the surface of polylactic acid (PLA) film by gamma radiation induced grafting of N-vinyl pyrrolidone (NVP). In this method, poly (N-vinyl pyrrolidone) (PVP) was produced and grafted onto the surface of PLA film by gamma radiation polymerization of NVP. PVP acted as both a bridge to connect the Ag NPs with the PLA film, and a stabilizer to protect the Ag NPs from agglomeration. The effect of various reaction parameters, including NVP/Ag mole ratio and radiation dose, on the fabrication of PLA-g-NVP/Ag film was demonstrated. Moreover, the interaction between PVP and Ag NPs was studied by X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy, that revealed the Ag NPs coordinated through the oxygen atom on the carbonyl group of PVP at 15 kGy radiation dose, but through the nitrogen atom and the oxygen atom of the amide group of PVP at 1 kGy dose. - Highlights: • PLA-graft-NVP/Ag film was produced by a simple one-step method. • Ag nanoparticles were immobilized on PLA film by gamma radiation grafting technology. • PVP acted as a bridge to connect Ag nanoparticles and PLA film. • Different content and size of Ag NPs can be reached by varying radiation dose.

In-situ formation of silver nanoparticles on poly (lactic acid) film by γ-radiation induced grafting of N-vinyl pyrrolidone

International Nuclear Information System (INIS)

Wang, Jingxia; Chen, Hao; Chen, Zhuping; Chen, Yuheng; Guo, Dan; Ni, Maojun; Liu, Siyang; Peng, Chaorong

2016-01-01

A fast, easy and novel method for preparing biodegradable polymer films with silver nanoparticles was investigated to endow the material with excellent biocompatibility and antibacterial property. Silver nanoparticles (Ag NPs) were immobilized on the surface of polylactic acid (PLA) film by gamma radiation induced grafting of N-vinyl pyrrolidone (NVP). In this method, poly (N-vinyl pyrrolidone) (PVP) was produced and grafted onto the surface of PLA film by gamma radiation polymerization of NVP. PVP acted as both a bridge to connect the Ag NPs with the PLA film, and a stabilizer to protect the Ag NPs from agglomeration. The effect of various reaction parameters, including NVP/Ag mole ratio and radiation dose, on the fabrication of PLA-g-NVP/Ag film was demonstrated. Moreover, the interaction between PVP and Ag NPs was studied by X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy, that revealed the Ag NPs coordinated through the oxygen atom on the carbonyl group of PVP at 15 kGy radiation dose, but through the nitrogen atom and the oxygen atom of the amide group of PVP at 1 kGy dose. - Highlights: • PLA-graft-NVP/Ag film was produced by a simple one-step method. • Ag nanoparticles were immobilized on PLA film by gamma radiation grafting technology. • PVP acted as a bridge to connect Ag nanoparticles and PLA film. • Different content and size of Ag NPs can be reached by varying radiation dose.

Radio-iodide uptake by modified poly (glycidyl methacrylate) as anion exchange resin

Energy Technology Data Exchange (ETDEWEB)

Othman, Sameh H. [Atomic Energy Authority, Cairo (Egypt). Nuclear Research Center; Atomic Energy Authority, Cairo (Egypt). Second Research Reactor; Elbarbary, Ahmed M. [Atomic Energy Authority, Cairo (Egypt). Radiation Research of Polymer Chemistry Dept.; Rashad, Ghada; Fasih, T.W. [Atomic Energy Authority, Cairo (Egypt). Hot Laboratories Center

2017-03-01

Poly(glycidyl methacrylate) (PGMA) microspheres were prepared by radiation induced polymerization of glycidyl methacrylate (GMA) monomer. The factors affecting the degree of polymerization and yield (%) of PGMA such as type of solvent, monomer concentration, and irradiation dose were investigated. It was found that the PGMA yield (%) increases with increasing monomer concentration up to 50% and absorbed dose of 5 kGy. The resulting PGMA containing the epoxy group was chemically modified by hydroxyl amine to act as anion-exchange resin for uptake of {sup 131}I{sup -} ions. The modified PGMA (MPGMA) was characterized by Fourier transform infrared (FT-IR) spectrophotometer, thermal gravimetric analysis (TGA) and scanning electron microscopy (SEM). I-131 is produced from the fission of U-235 with low-enrichment uranium (LEU) targets in the Egyptian Second Research Reactor (ETRR-2). Separation of iodide from the radioactive solution by batchwise and column techniques was employed to determine the adsorption capacity of the MPGMA. Quality control of {sup 131}I product solution and radiochemical purity was examined by using the ascending paper chromatography method. The uptake behavior of MPGMA towards {sup 131}I{sup -} ions were studied at different experimental conditions and achieved by X-ray fluorescence (XRF). The synthesized MPGMA showed good results as anion-exchange and an effective adsorbent for uptaking {sup 131}I{sup -} ions.

Coating materials

International Nuclear Information System (INIS)

Ozeki, Takao; Kimura, Tadashi; Kobayashi, Juichi; Maeda, Yutaka; Nakamoto, Hideo.

1969-01-01

A non-solvent type coating material composition is provided which can be hardened by irradiation with active energy, particularly electron beams, using a composition which contains 10%-100% of a radically polymerizable low molecular compound (A), (hereafter called an oligomer), having at least two vinyl radicals in one molecule. These compositions have a high degree of polymerization and characteristics equivalent to thermosetting acrylic or amino alkyd resin. The oligomer (A) is produced by reacting an epoxy-containing vinyl monomer with saturated polycarboxylic acids or anhydrides. In one embodiment, 146 parts by weight of adipic acid and 280 parts of glycidyl methacrylate ester undergo addition reaction in the presence of a polymerization-inhibitor and a catalyst at 90 0 C for 6 hours to produce an oligomer having a fiberous divinyl construction. The coating composition utilizes this oligomer in the forms of (I-1), a whole oligomer; (I-2), 0%-90% of this oligomer and 90%-10% of a vinyl monomer containing at least 30% of (meth) acrylic monomer; (I-3), 10%-90% of such oligomer and 90%-10% of other monomers containing at least two vinyl radicals in one molecule; (I-4), a mixture of (I-2) and (I-3) in proportion of 1/9 to 9/1, and (I-5), above four compositions each containing 50% or less unsaturated polyester or drying oil having 500-5,000 molecules or a drying oil-modified alkyd resin having 500-5,000 molecules. Four examples are given. (Iwakiri, K.)

Manipulating Interfaces through Surface Confinement of Poly(glycidyl methacrylate)-block-poly(vinyldimethylazlactone), a Dually Reactive Block Copolymer

International Nuclear Information System (INIS)

Lokitz, Bradley S.; Wei, Jifeng; Hinestrosa Salazar, Juan P.; Ivanov, Ilia N.; Browning, James B.; Ankner, John Francis; Kilbey, S. Michael II; Messman, Jamie M.

2012-01-01

The assembly of dually reactive, well-defined diblock copolymers incorporating the chemoselective/functional monomer, 4,4-dimethyl-2-vinylazlactone (VDMA) and the surface-reactive monomer glycidyl methacrylate (GMA) is examined to understand how competition between surface attachment and microphase segregation influences interfacial structure. Reaction of the PGMA block with surface hydroxyl groups not only anchors the copolymer to the surface, but limits chain mobility, creating brush-like structures comprising PVDMA blocks, which contain reactive azlactone groups. The block copolymers are spin coated at various solution concentrations and annealed at elevated temperature to optimize film deposition to achieve a molecularly uniform layer. The thickness and structure of the polymer thin films are investigated by ellipsometry, infrared spectroscopy, and neutron reflectometry. The results show that deposition of PGMA-b-PVDMA provides a useful route to control film thickness while preserving azlactone groups that can be further modified with biotin-poly(ethylene glycol)amine to generate designer surfaces. The method described herein offers guidance for creating highly functional surfaces, films, or coatings through the use of dually reactive block copolymers and postpolymerization modification.

Fabrication and Evaluation of 2-Hydroxyethyl Methacrylate-co ...

African Journals Online (AJOL)

Purpose: To fabricate and evaluate oral 2-hydroxyethyl methacrylate co-acrylic acid hydrogels as a drug delivery system for sustained release of nicorandil. Methods: HEMA-co-AA hydrogels using different monomer concentrations were prepared by free radical polymerization. N, N-methylene bis acrylamide (MBA) was ...

Biomonitoring of N-ethyl-2-pyrrolidone in automobile varnishers.

Science.gov (United States)

Koslitz, Stephan; Meier, Swetlana; Schindler, Birgit Karin; Weiss, Tobias; Koch, Holger Martin; Brüning, Thomas; Käfferlein, Heiko Udo

2014-12-01

N-alkyl-2-pyrrolidones are important organic solvents for varnishes in industry. This study investigates exposure to N-ethyl-2-pyrrolidone (NEP) in varnishing of hard plastic components in an automobile plant. Two specific biomarkers of exposure, 5-hydroxy-N-ethyl-2-pyrrolidone (5-HNEP) and 2-hydroxy-N-ethylsuccinimide (2-HESI), were analyzed in urine samples of 14 workers. For this purpose, pre-shift, post-shift and next day pre-shift urine samples were collected midweek. Twelve workers performed regular work tasks (loading, wiping and packing), whereas two workers performed special work tasks including cleaning the sprayer system with organic solvents containing N-alkyl-2-pyrrolidones. Spot urine samples of nine non-exposed persons of the same plant served as controls. Median post-shift urinary levels of workers with regular work tasks (5-HNEP: 0.15 mg/L; 2-HESI: 0.19 mg/L) were ∼5-fold higher compared to the controls (0.03 mg/L each). Continuously increasing metabolite levels, from pre-shift via post-shift to pre-shift samples of the following day, were observed in particular for the two workers with the special working tasks. Maximum levels were 31.01 mg/L (5-HNEP) and 8.45 mg/L (2-HESI). No clear trend was evident for workers with regular working tasks. In summary, we were able to show that workers can be exposed to NEP during varnishing tasks in the automobile industry. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Preparation and characterization of chitosan/genipin/poly(N-vinyl-2-pyrrolidone) films for controlled release drugs

Energy Technology Data Exchange (ETDEWEB)

Aldana, Ana Agustina, E-mail: aaldana@fcq.unc.edu.ar [Departamento de Quimica Organica, Facultad de Ciencias Quimicas, Universidad Nacional de Cordoba (UNC), Edificio de Ciencias II, Medina Allende y Haya de la Torre, Ciudad Universitaria, Cordoba 5000 (Argentina); Gonzalez, Agustin, E-mail: agustingonzalez@fcq.unc.edu.ar [Departamento de Quimica Organica, Facultad de Ciencias Quimicas, Universidad Nacional de Cordoba (UNC), Edificio de Ciencias II, Medina Allende y Haya de la Torre, Ciudad Universitaria, Cordoba 5000 (Argentina); Strumia, Miriam C., E-mail: mcs@fcq.unc.edu.ar [Departamento de Quimica Organica, Facultad de Ciencias Quimicas, Universidad Nacional de Cordoba (UNC), Edificio de Ciencias II, Medina Allende y Haya de la Torre, Ciudad Universitaria, Cordoba 5000 (Argentina); Martinelli, Marisa, E-mail: mmartinelli@fcq.unc.edu.ar [Departamento de Quimica Organica, Facultad de Ciencias Quimicas, Universidad Nacional de Cordoba (UNC), Edificio de Ciencias II, Medina Allende y Haya de la Torre, Ciudad Universitaria, Cordoba 5000 (Argentina)

2012-05-15

Highlights: Black-Right-Pointing-Pointer Cross-linked chitosan films using genipin and/or PVP. Black-Right-Pointing-Pointer Propranolol hydrochloride was used like a model drug to release studies. Black-Right-Pointing-Pointer Incorporating PVP improves mechanical and diffusion properties. Black-Right-Pointing-Pointer Ch-Gen 0.10% and Ch-Gen 0.10%-PVP have optimal behavior. - Abstract: The study of the physicochemical and functional properties of chitosan films cross-linked with genipin and poly(N-vinyl-2-pyrrolidone) (PVP) was performed in this work. Cross-linked films were prepared by casting method from acetic acid solutions. The structure and physical properties of the films were analyzed by infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy ({sup 13}C NMR), differential scanning calorimetry (DSC) and mechanical testings. Propranolol hydrochloride was used like a model drug to determine the behavior of drug release from films. The drug release capacity was measured and compared with the degree of cross-linking, mechanical properties and swelling index. There was an appropriate balance of hydrophilicity, mechanical properties and diffusion by the incorporation of PVP into the networks cross-linked with genipin. The combination of both cross-linkers allows obtaining a soft and tough material potentially applicable as a controlled release. This research represents the first report where both cross-linkers, chemical and ionic agents, are used for obtaining films. These studies suggest that the chitosan films prepared here are promising drug delivery systems for buccal application, with thermal stability and acceptable mechanical properties. Buccal films may be preferred in terms of flexibility and comfort.

Preparation and characterization of chitosan/genipin/poly(N-vinyl-2-pyrrolidone) films for controlled release drugs

International Nuclear Information System (INIS)

Aldana, Ana Agustina; González, Agustín; Strumia, Miriam C.; Martinelli, Marisa

2012-01-01

Highlights: ► Cross-linked chitosan films using genipin and/or PVP. ► Propranolol hydrochloride was used like a model drug to release studies. ► Incorporating PVP improves mechanical and diffusion properties. ► Ch–Gen 0.10% and Ch–Gen 0.10%–PVP have optimal behavior. - Abstract: The study of the physicochemical and functional properties of chitosan films cross-linked with genipin and poly(N-vinyl-2-pyrrolidone) (PVP) was performed in this work. Cross-linked films were prepared by casting method from acetic acid solutions. The structure and physical properties of the films were analyzed by infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy ( 13 C NMR), differential scanning calorimetry (DSC) and mechanical testings. Propranolol hydrochloride was used like a model drug to determine the behavior of drug release from films. The drug release capacity was measured and compared with the degree of cross-linking, mechanical properties and swelling index. There was an appropriate balance of hydrophilicity, mechanical properties and diffusion by the incorporation of PVP into the networks cross-linked with genipin. The combination of both cross-linkers allows obtaining a soft and tough material potentially applicable as a controlled release. This research represents the first report where both cross-linkers, chemical and ionic agents, are used for obtaining films. These studies suggest that the chitosan films prepared here are promising drug delivery systems for buccal application, with thermal stability and acceptable mechanical properties. Buccal films may be preferred in terms of flexibility and comfort.

PEGylation of magnetic poly(glycidyl methacrylate) microparticles for microfluidic bioassays

International Nuclear Information System (INIS)

Kucerova, Jana; Svobodova, Zuzana; Knotek, Petr; Palarcik, Jiri; Vlcek, Milan; Kincl, Miloslav; Horak, Daniel; Autebert, Julien; Viovy, Jean-Louis; Bilkova, Zuzana

2014-01-01

In this study, magnetic poly(glycidyl methacrylate) microparticles containing carboxyl groups (PGMA-COOH) were coated using highly hydrophilic polymer poly(ethylene glycol) (PEG). PEG was used to reduce nonspecific interactions with proteins and cells while decreasing adhesion of particles to the walls of a microfluidic devices from poly(dimethylsiloxane) (PDMS) and cyclic olefin copolymer (COC). Zeta potential measurement, infrared spectroscopy, scanning electron microscopy, anti-PEG ELISA assay, and bioaffinity interactions between biotin and streptavidin-HRP successfully proved the presence of PEG on the surface of microspheres. Both neat and PEGylated microspheres were then incubated with the inert protein bovine serum albumin or cells to evaluate the rate of nonspecific adsorption (NSA). PEG with Mr of 30,000 Da was responsible for 45% reduction in NSA of proteins and 74% for cells compared to neat particles. The microspheres' behavior in PDMS and COC microchannels was then evaluated. Aggregation and adhesion of PEGylated microspheres significantly decreased compared to neat particles. Finally, the model enzyme horseradish peroxidase was immobilized on the microspheres through the heterobifunctional PEG chain. The possibility for subsequent covalent coupling of the ligand of interest was confirmed. Such PEGylated microparticles can be efficiently used in PDMS microchips as a carrier for bioaffinity separation or of enzyme for catalysis. - Highlights: • Magnetic polymer microspheres with highly hydrophilic PEG coating were prepared. • PEG reduced microsphere adhesion in microchannels versus neat particles. • Suitability of methods for detecting PEG on magnetic microspheres was investigated. • PEG on microsphere surfaces decreased nonspecific adsorption of proteins and cells

PEGylation of magnetic poly(glycidyl methacrylate) microparticles for microfluidic bioassays

Energy Technology Data Exchange (ETDEWEB)

Kucerova, Jana; Svobodova, Zuzana [Department of Biological and Biochemical Sciences, Faculty of Chemical Technology, University of Pardubice, Studentska 573, 53210 Pardubice (Czech Republic); Knotek, Petr [Joint Laboratory of Solid State Chemistry of IMC and University of Pardubice, Faculty of Chemical Technology, University of Pardubice, Studentska 573, 53210 Pardubice (Czech Republic); Palarcik, Jiri [Institute of Environmental and Chemical Engineering, Faculty of Chemical Technology, University of Pardubice, Studentska 573, 53210 Pardubice (Czech Republic); Vlcek, Milan; Kincl, Miloslav; Horak, Daniel [Institute of Macromolecular Chemistry, Academy of Sciences of the Czech Republic, Heyrovsky Sq. 2, 16206 Prague 6 (Czech Republic); Autebert, Julien; Viovy, Jean-Louis [Macromolecules and Microsystems in Biology and Medicine, Institute Curie, UMR 168, 26 Rue d' Ulm, 75005 Paris (France); Bilkova, Zuzana, E-mail: zuzana.bilkova@upce.cz [Department of Biological and Biochemical Sciences, Faculty of Chemical Technology, University of Pardubice, Studentska 573, 53210 Pardubice (Czech Republic)

2014-07-01

In this study, magnetic poly(glycidyl methacrylate) microparticles containing carboxyl groups (PGMA-COOH) were coated using highly hydrophilic polymer poly(ethylene glycol) (PEG). PEG was used to reduce nonspecific interactions with proteins and cells while decreasing adhesion of particles to the walls of a microfluidic devices from poly(dimethylsiloxane) (PDMS) and cyclic olefin copolymer (COC). Zeta potential measurement, infrared spectroscopy, scanning electron microscopy, anti-PEG ELISA assay, and bioaffinity interactions between biotin and streptavidin-HRP successfully proved the presence of PEG on the surface of microspheres. Both neat and PEGylated microspheres were then incubated with the inert protein bovine serum albumin or cells to evaluate the rate of nonspecific adsorption (NSA). PEG with Mr of 30,000 Da was responsible for 45% reduction in NSA of proteins and 74% for cells compared to neat particles. The microspheres' behavior in PDMS and COC microchannels was then evaluated. Aggregation and adhesion of PEGylated microspheres significantly decreased compared to neat particles. Finally, the model enzyme horseradish peroxidase was immobilized on the microspheres through the heterobifunctional PEG chain. The possibility for subsequent covalent coupling of the ligand of interest was confirmed. Such PEGylated microparticles can be efficiently used in PDMS microchips as a carrier for bioaffinity separation or of enzyme for catalysis. - Highlights: • Magnetic polymer microspheres with highly hydrophilic PEG coating were prepared. • PEG reduced microsphere adhesion in microchannels versus neat particles. • Suitability of methods for detecting PEG on magnetic microspheres was investigated. • PEG on microsphere surfaces decreased nonspecific adsorption of proteins and cells.

Effect of glycidyl methacrylate (GMA) incorporation on water uptake and conductivity of proton exchange membranes

Science.gov (United States)

Sproll, Véronique; Schmidt, Thomas J.; Gubler, Lorenz

2018-03-01

The aim of this work was to investigate how hygroscopic moieties like hydrolyzed glycidyl methacrylate (GMA) influence the properties of sulfonated polysytrene based proton exchange membranes (PEM). Therefore, several membranes were synthesized by electron beam treatment of the ETFE (ethylene-alt-tetrafluoroethylene) base film with a subsequent co-grafting of styrene and GMA at different ratios. The obtained membranes were sulfonated to introduce proton conducting groups and the epoxide moiety of the GMA unit was hydrolyzed for a better water absorption. The PEM was investigated regarding its structural composition, water uptake and through-plane conductivity. It could be shown that the density of sulfonic acid groups has a higher influence on the proton conductivity of the PEM than an increased water uptake.

In vitro release studies of vitamin B12 from poly N-vinyl pyrrolidone /starch hydrogels grafted with acrylic acid synthesized by gamma radiation

International Nuclear Information System (INIS)

Eid, M.

2008-01-01

Co-polymeric hydrogels containing N-vinyl pyrrolidone and starch grafted with acrylic acid were synthesized by gamma radiation. Their gel contents, grafting process and swelling were evaluated. The gels were also characterized by thermal gravimetric analysis. The gel content found to be increase with increasing the irradiation dose up to 50 kGy then decrease. The grafting percent increase by increasing the percentage of acrylic acid in the grafted hydrogels. The thermal stability and the rate of the thermal decomposition showed to be changed according to the different composition of the hydrogels. It also showed a decrease in the maximum rate of the thermal decomposition by the increasing of the irradiation dose from 20 to 30 kGy and increases by increasing the irradiation dose from 30 to 70 kGy. The hydrogels loaded with vitamin B 12 as drug model, demonstrated a decrease release in acidic medium than the neutral one

Preparation of various hydrogels based on poly (Vinyl pyrrolidone) and poly ethylene glycol using gamma and electron irradiation

International Nuclear Information System (INIS)

Ajji, Z.

2006-11-01

Different hydrogels have been prepared using gamma and electron irradiation; the hydrogels are composed of poly(vinyl pyrolidone) (PVP), poly(ethylene glycol) (PEG). The influence of some process parameters on the properties of the hydrogels has been investigated as: the gel fraction, maximum swelling, swelling kinetics, and mechanical properties. In the first part of this study, hydrogel dressings have been prepared using electron irradiation, and the dressings are composed of poly(vinyl pyrrolidone) (PVP), poly(ethylene glycol) (PEG) and agar. The gel fraction increases with increasing PVP concentration due to increased crosslink density, and decreases with increasing the PEG concentration. PEG seems to act not only as plasticizer but also to modify the gel properties as gelation% and maximum swelling. The prepared hydrogels dressings could be considered as a good barrier against microbes. In the second part, different hydrogels have been prepared based on different concentrations of poly(vinyl pyrrolidone) and using gamma irradiation. The gel fraction and maximum swelling of the hydrogels has been determined. In the third part of the study, different hydrogels have been prepared based on different concentrations of poly(vinyl pyrrolidone) and poly(ethylene glycol) (PEG) with various molecular weights, and using gamma irradiation. The gel fraction and maximum swelling of the hydrogels has been determined. The data show that PEG with low molecular weight needs a high dose for the gelation, and the presence of PVP lowers the needed gelation dose. The maximum swelling decreases with increasing irradiation dose and the PVP concentration, which is due to higher crosslinks between the polymer chains. (author)

Sorption of different phenol derivatives on functionalized macroporous nanocomposite of poly (glycidyl methacrylate-co-ethylene glycol dimethacrylate and acid modified bentonite

Directory of Open Access Journals (Sweden)

Marinović Sanja R.

2014-01-01

Full Text Available Macroporous nanocomposite of poly (glycidyl methacrylate-co-ethylene glycol dimethacrylate and acid modified bentonite was prepared by radical suspension copolymerization. Nanocomposite was functionalized with diethylene triamine (deta, by ring-opening reaction of the pendant epoxy groups. Functionalization was performed in order to enable phenol derivatives sorption. This new, not sufficiently investigated material, with developed porous structure was denoted CP-SA-deta. In this study, the influence of temperature on 4-nitrophenol (4NP sorption on CP-SA-deta was investigated. The chemisorption was estimated as dominant process since activation energy of sorption of 4NP of 54.8 kJ mol-1 was obtained. After determining the optimal sorption conditions for 4NP, the sorption of 2-nitrophenol (2NP and 2-chloro 4-nitrophenol (2Cl4NP on CP-SA-deta was investigated with respect to pH, initial concentration and contact time. The 2NP sorption was seldom tested, while according to our knowledge, the 2Cl4NP sorption was not investigated. The isotherm data were best fitted with Langmuir model, while the sorption dynamics obeyed the pseudo-second-order kinetic model for all derivatives. [Projekat Ministarstva nauke Republike Srbije, br. III 45001 i br. III 43009

Effect of immobilized amine density on cadmium(II) adsorption capacities for ethanediamine-modified magnetic poly-(glycidyl methacrylate) microspheres

Energy Technology Data Exchange (ETDEWEB)

Dong, Tingting [Key Laboratory of Green Process and Engineering, State Key Laboratory of Biochemical Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Yang, Liangrong, E-mail: lryang@ipe.ac.cn [Key Laboratory of Green Process and Engineering, State Key Laboratory of Biochemical Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Pan, Feng; Xing, Huifang; Wang, Li; Yu, Jiemiao [Key Laboratory of Green Process and Engineering, State Key Laboratory of Biochemical Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Qu, Hongnan [Key Laboratory of Green Process and Engineering, State Key Laboratory of Biochemical Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao 266101 (China); Rong, Meng [Key Laboratory of Green Process and Engineering, State Key Laboratory of Biochemical Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Huizhou, E-mail: hzliu@ipe.ac.cn [Key Laboratory of Green Process and Engineering, State Key Laboratory of Biochemical Engineering, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190 (China)

2017-04-01

A series of ethanediamine (EDA) – modified magnetic poly-(glycidyl methacrylate) (m-PGMA-EDA)microspheres with different amine density were synthesized and their cadmium saturation adsorption capacities were examined. The results showed that the cadmium saturation adsorption capacity increased with the immobilized amine density. However, they did not show strong positive linear correlation in the whole range of amine density examined. The molar ratio of amine groups to the adsorbed cadmium decreased with the increase of amine density and eventually reached a minimum value about 4. It suggested that low immobilized amine density led to low coordination efficiency of the amine. It is hypothesized that the immobilized amine groups needed to be physically close enough to form stable amine-metal complex. When the amine density reached to a critical value 1.25 m mol m{sup −2}, stable amine-cadmium complex (4:1 N/Cd) was proposed to form. To illustrate the coordination mechanism (structure and number) of amine and Cd, FT-IR spectra of m-PGMA-EDA and m-PGMA-EDA-Cd , and X-ray photoelectron spectroscopy (XPS) of PGMA–EDA and PGMA-EDA-Cd were examined and analyzed. - Highlights: • A series of magnetic poly-(glycidyl methacrylate) (m-PGMA-EDA)microspheres with different amine density were synthesized and their cadmium saturation adsorption capacities were examined. • The molar ratio of amine groups to adsorbed cadmium decreased with the increase of amine density and eventually reached a minimum value about 4. • when the amine density reached high enough, 4:1 N/Cd complex was proposed to form, and the hydroxyl also participated in the chelating with Cd.

Wax inhibitor based on ethylene vinyl acetate with methyl methacrylate and diethanolamine for crude oil pipeline

Science.gov (United States)

Anisuzzaman, S. M.; Abang, S.; Bono, A.; Krishnaiah, D.; Karali, R.; Safuan, M. K.

2017-06-01

Wax precipitation and deposition is one of the most significant flow assurance challenges in the production system of the crude oil. Wax inhibitors are developed as a preventive strategy to avoid an absolute wax deposition. Wax inhibitors are polymers which can be known as pour point depressants as they impede the wax crystals formation, growth, and deposition. In this study three formulations of wax inhibitors were prepared, ethylene vinyl acetate, ethylene vinyl acetate co-methyl methacrylate (EVA co-MMA) and ethylene vinyl acetate co-diethanolamine (EVA co-DEA) and the comparison of their efficiencies in terms of cloud point¸ pour point, performance inhibition efficiency (%PIE) and viscosity were evaluated. The cloud point and pour point for both EVA and EVA co-MMA were similar, 15°C and 10-5°C, respectively. Whereas, the cloud point and pour point for EVA co-DEA were better, 10°C and 10-5°C respectively. In conclusion, EVA co-DEA had shown the best % PIE (28.42%) which indicates highest percentage reduction of wax deposit as compared to the other two inhibitors.

Controlled protein adsorption on PMOXA/PAA based coatings by thermally induced immobilization

Science.gov (United States)

Mumtaz, Fatima; Chen, Chaoshi; Zhu, Haikun; Pan, Chao; Wang, Yanmei

2018-05-01

In this work, poly(2-methyl-2-oxazoline-random-glycidyl methacrylate) (PMOXA-r-GMA) and poly(acrylic acid)-block-poly(glycidyl methacrylate) (PAA-b-PGMA) copolymers were synthesized via cationic ring-opening polymerization (CROP) of 2-methyl-2-oxazoline (MOXA) and reversible addition-fragmentation chain transfer (RAFT) polymerization of acrylic acid (AA) followed by their random and block copolymerization with glycidyl methacrylate (GMA), respectively, and then characterized carefully. PMOXA/PAA based coatings were then prepared by simply spin coating the mixture of PMOXA-r-GMA and PAA-b-PGMA copolymer solutions onto silicon/glass substrates followed by annealing at 110 °C. The coatings were rigorously characterized by using X-ray photoelectron spectroscopy (XPS), the static water contact angle (WCA) test, ellipsometry and atomic force microscopy (AFM). The results demonstrated that the coating based mixed PMOXA/PAA brushes with desired surface composition could be attained by simply maintaining their percentage in the mixture of PMOXA-r-GMA and PAA-b-PGMA copolymer solutions. Finally, the switchable behavior of PMOXA/PAA based coatings toward bovine serum albumin (BSA) adsorption was investigated by fluorescein isothiocyanate-labelled BSA (FITC-BSA) assay and quartz crystal microbalance with dissipation monitoring (QCM-D), which indicated that the coating based mixed PMOXA/PAA brushes could control BSA adsorption/desorption from very low to high amount (>90% desorption) through adjusting the composition of PMOXA-r-GMA and PAA-b-PGMA solution used in preparing PMOXA/PAA based coatings upon pH and ionic strength change. Furthermore, PMOXA/PAA based coatings displayed efficient repeatability of reversible BSA adsorption/desorption cycles.

High Performance Affinity Chromatography of Antithrombin III Based on Monodisperse Poly (glycidyl methacrylate) Beads

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

A new approach for the separation of antithrombin III with high performance affinity chromatography (HPAC) was described. A novel monodisperse,non-porous,cross-linked poly (glycidyl methacrylate) beads (PGMA) were used as the affinity support. With the water-soluble carbodiimide,heparin was linked covalently to amino-PGMA-beads,which was prepared by amination of PGMA. The adsorbent obtained exhibits high binding activity to antithrombin III (ATIII),good resolution and excellent mechanical properties and can be used under high flow rate.

Poly(glycidyl methacrylate)/silver nanocomposite microspheres as a radioiodine scavenger: electrophoretic characterisation of carboxyl- and amine-modified particles

Czech Academy of Sciences Publication Activity Database

Macková, Hana; Oukacine, F.; Plichta, Zdeněk; Hrubý, Martin; Kučka, Jan; Taverna, M.; Horák, Daniel

2014-01-01

Roč. 421, 1 May (2014), s. 146-153 ISSN 0021-9797 R&D Projects: GA MŠk 7E12053; GA ČR GAP503/10/0664 EU Projects: European Commission(XE) 246513 - NADINE Institutional support: RVO:61389013 Keywords : glycidyl methacrylate * microspheres * silver Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.368, year: 2014

Process for preparing coating materials

International Nuclear Information System (INIS)

Ryoke, Hideyasu; Kobayashi, Juichi; Kobayashi, Kei.

1972-01-01

A coating material curable with ionizing radiations or ultraviolet radiation can be prepared by reacting a compound (A) having one OH group and at least one α,β-ethylenic or allyl group with a polyisocyanate. (A) is a diester of a dicarboxylic acid. One of the ester groups may have a terminal α,β-ethylenic or allyl group and the other contains one OH and one α,β-ethylenic or allyl group. (A) is reacted with a polyisocyanate to yield an urethane. The latter may be diluted with a vinyl monomer. When exposed to a radiation, the coating material cures to give a film excellent in adhesion, impact strength and resistances to pollution, water and solvents. Dose of the ionizing radiation (α-, β-, γ-rays, electron beams) is 0.2-20 Mrad. In one example, 116 parts of 2-hydroxyethyl acrylate was reacted with 148 parts of phthalic anhydride and 142 parts of glycidyl methacrylate to give (A). (A) was reacted with 87 parts of tolylenediisocyanate. A metallic panel was coated with the coating material and cured with electron beams (5 Mrad). Pencil hardness was H, and gel fraction measured in acetone was above 97%. The coating was excellent in resistances to solvent and chemicals, impact strength and adhesion. (Kaichi, S.)

Radiation synthesis of size-controlled poly(N-vinyl pyrrolidone) nanogels and their use as antimicrobial agents

International Nuclear Information System (INIS)

Isik, S.D.; Gueven, O.

2011-01-01

Complete text of publication follows. Nanogels are swollen networks of hydrophilic polymers generally developed to carry drugs, proteins and biologically active substances for biomedical applications. They can be prepared by 1) physical assembling of interactive polymers, 2) polymerization of monomers in micro or nanoscale environment, 3) crosslinking of preformed polymers, 4) template-assisted nanofabrication of nanogel particles. Among these methods crosslinking of preformed polymer chains provide excellent applications, especially when ionizing radiation is used as the tool to induce crosslinking. Due to its low cytotoxicity, excellent biocompatibility and non-carcinogenic and non-allergic properties, poly(N-vinyl pyrrolidone) (PVP) has been widely used in biomedical applications, hence the main reason for its selection in this work for the synthesis of its nanogels. PVP nanogels were prepared by gamma irradiation of its dilute aqueous solutions up to 15 kGy. The coil sizes of PVP chains were initially controlled by using acetone/water mixture as the solvent and further irradiations fixed the sizes by intramolecular crosslinking. By changing the concentration of PVP solutions, solvent composition and dose it was possible to prepare nanogels within 40-230 nm sizes. The nanogels were characterized by dynamic light scattering, scanning electron microscopy and atomic force microscopy. GPC has also been used to follow the changes in the coil sizes and distributions upon irradiations. The PVP nanogels thus synthesized were complexed with iodine in aqueous KI-I 2 solutions. Nanogels comprised of typical PVP-iodine complexes were tested for their antiseptic properties.

Concanavalin A immobilized magnetic poly(glycidyl methacrylate) beads for prostate specific antigen binding.

Science.gov (United States)

Idil, Neslihan; Perçin, Işık; Karakoç, Veyis; Yavuz, Handan; Aksöz, Nilüfer; Denizli, Adil

2015-10-01

The aim of this study was to prepare Concanavalin A (Con A) immobilized magnetic poly(glycidyl methacrylate) (mPGMA) beads for prostate specific antigen (PSA) binding and to study binding capacities of the beads using lectin-glycoprotein interactions. Firstly, iron oxide nanoparticles were synthesized by co-precipitation method and then, beads were synthesized by dispersion polymerization in the presence of iron oxide nanoparticles. Con A molecules were both covalently immobilized onto the beads directly and through the spacer arm (1,6-diaminohexane-HDMA). The total PSA and free PSA binding onto the mPGMA-HDMA-Con A beads were higher than that of the mPGMA-Con A beads. Maximum PSA binding capacity was observed as 91.2 ng/g. Approximately 45% of the bound PSA was eluted by using 0.1 M mannose as elution agent. The mPGMA-HDMA-Con A beads could be reused without a remarkable decrease in the binding capacities after 5 binding-desorption cycles. Serum fractions were analyzed using SDS-PAGE. The mPGMA-HDMA-Con A beads could be useful for the detection of PSA and suggested as a model system for other glycoprotein biomarkers. Copyright © 2015 Elsevier B.V. All rights reserved.

Evaluation of morphology and cell behaviour of a novel synthesized electrospun poly(vinyl pyrrolidone/poly(vinyl alcohol/hydroxyapatite nanofibers

Directory of Open Access Journals (Sweden)

Raheleh Faridi-Majidi

2017-04-01

Full Text Available Objective(s: Three-dimensional structures such as nanofibrous scaffolds are being used in biomedical engineering as well as provide a site for cells to attach and proliferate leading to tissue formation. In the present study, poly(vinyl pyrrolidone (PVP/ poly(vinyl alcohol(PVA hybrid nanofibrous scaffold was synthesized by electrospinning. Materials and Methods: The effect of adding nano hydroxyapatite (n-HA and also Epoxypropoxy-propyl-trimethoxysilane (EPPTMS as a crosslinking agent on morphology and cell behaviour of the nanofibers was investigated.Results: Scanning electron microscope (SEM observations showed that all kinds of nanofibers represented uniform and well-ordered morphologies without formation of any beads by controlling the synthesis parameters. The average ûber diameter of PVP-PVA was 260 nm. n-HA was synthesized by wet chemical process. The synthesized n-HA was characterized by XRD for structural analysis. Transmission electron microscope (TEM revealed that HA particles had nanosized dimensions (in the range of 40-100 nm. The presence of n-HA within electrospun PVP-PVA nanofibers was confirmed by XRD and Fourier transmission infrared spectroscopy (FTIR analyses. The average ûber diameter was decreased to 136 nm when n-HA was added in the composition of PVP-PVA. FTIR analysis depicted that PVP-PVA nanofibers were linked to EPPTMS as a biocompatible material by the covalent bond. Although adding n-HA caused to decrease the diameter of PVP-PVA nanofibers, addition of EPPTMS within PVP/PVA/n-HA nanofibers induced increasing distribution of fiber diameter as it enhanced to 195nm. In addition, the proper proliferation of G292 osteoblastic cells without any cytotoxicity was observed for the nanofiber.Conclusion: Since these materials have been known as biomaterials, PVP/PVA/n-HA-EPPTMS nanofibers can be propounded as a good candidate for bone tissue engineering application.

Radiation-curable coating composition

International Nuclear Information System (INIS)

Mibae, Jiro; Kawamura, Hiroshi; Takahashi, Masao.

1970-01-01

A radiation-curable coating composition, suitable for metal precoating, is provided. The composition is prepared by mixing 50 to 90 parts of a long chain fatty acid ester (A) with 10 to 50 parts of monomer (B) which is copolymerizable with (A). (A) is prepared by reacting a dimer acid (particularly the dimer of linolenic acid) with hydroxyalkyl methacrylate or glycidyl methacrylate. Upon irradiation with electron beams (0.1 to 3 MeV) the composition cures to yield a coating of high adhesion, impact resistance and bending resistance. In one example, 100 g of dimer acid (Versadime 216, manufactured by General Mills) was esterified with 50 g of 2-hydroxyethyl methacrylate. A zinc plated iron plate was coated with the product and irradiated with electron beams (2 Mrad). Pencil hardness was F; adhesion 0: impact resistance (Du Pont) 1 kg x 30 cm; bending resistance 2T. (Kaichi, S.)

Poly(vinyl pyrrolidone) (PVP) hydrogels study for ophthalmologic area utilization

International Nuclear Information System (INIS)

Amaral, Renata Hage; Rogero, Sizue Ota; Lugao, Ademar Benevolo; Cruz, Aurea S.; Sacramento, Rogerio S.; Lima Filho, Acacio A. Souza; Schor, Paulo

2005-01-01

Poly (vinyl pyrrolidone) (PVP) hydrogels produced by radiation-induced crosslinking were studied to compose drug delivery system to be used in the eye surface and to manufacture ophthalmic plugs. Some formulations with PVP and poly ethylene glycol (PEG) with different molar mass (300 and 600) were prepared utilizing 0.85% sodium chloride aimed to control the swelling capacity. The obtained hydrogels were characterized by gel fraction and swelling assays. The gel fraction and swelling results indicated no difference in the formulation containing or not NaCl. The gel fraction results varied from 62 to 81% and the swelling degree from 130 to 420%. In vitro assay of cytotoxicity by neutral red uptake method was the first biocompatibility test performed. The results showed no evidence of toxicity in the studied hydrogels. (author)

Determination of the Thermodynamic Properties of Poly [2-(3-phenyl-3-methylcyclobutyl)-2-hydroxyethyl methacrylate-co-methacrylic acid] at Infinite Dilution by Inverse Gas Chromatography

OpenAIRE

KAYA, İsmet

2014-01-01

Some thermodynamic quantities were obtained for the interactions of poly [2-(3-phenyl -3- methylcyclobutyl)-2-hydroxyethyl methacrylate-co-methacrylic acid] Poly (PCHEMA-co-MA) with alcohols, ketones, acetates, aromatics and n-alkanes by inverse gas chromatography in the temperature range of 150-180oC. The specific retention volumes, Vgo, weight fraction activity coefficients of solute probes at infinite dilution, W1\\infty and Flory-Huggins thermodynamic interaction parameters, c12...

Densities and derived thermodynamic properties of the binary systems of 1,1-dimethylethyl methyl ether with allyl methacrylate, butyl methacrylate, methacrylic acid, and vinyl acetate at T = (298.15 and 308.15) K

International Nuclear Information System (INIS)

Wisniak, Jaime; Peralta, Rene D.; Infante, Ramiro; Cortez, Gladis

2005-01-01

Densities of the binary systems of 1,1-dimethylethyl methyl ether (MTBE) with allyl methacrylate, butyl methacrylate, methacrylic acid, and vinyl acetate have been measured as a function of the composition, at 298.15 and 308.15 K and atmospheric pressure, using an Anton Paar DMA 5000 oscillating U-tube densimeter. The calculated excess molar volumes were correlated with the Redlich-Kister equation and with a series of Legendre polynomials. The excess molar volumes are negative for the binaries of MTBE + methacrylates; the system MTBE with vinyl acetate presents near ideal behavior. The excess coefficient of thermal expansion is positive for all the systems studied here; the value of the coefficient for the system MTBE + allyl methacrylate is at least three times larger than that for the other systems

Immunocapture of CD133-positive cells from human cancer cell lines by using monodisperse magnetic poly(glycidyl methacrylate) microspheres containing amino groups

Czech Academy of Sciences Publication Activity Database

Kuan, W.-C.; Horák, Daniel; Plichta, Zdeněk; Lee, W.-C.

2014-01-01

Roč. 34, 1 January (2014), s. 193-200 ISSN 0928-4931 R&D Projects: GA ČR GCP207/12/J013 Institutional support: RVO:61389013 Keywords : magnetic * poly(glycidyl methacrylate) * microspheres Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.088, year: 2014

Poly(glycidyl methacrylate) grafted CdSe quantum dots by surface-initiated atom transfer radical polymerization: Novel synthesis, characterization, properties, and cytotoxicity studies

Energy Technology Data Exchange (ETDEWEB)

Bach, Long Giang; Islam, Md. Rafiqul [Department of Imaging System Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of); Lee, Doh Chang [Department of Chemical and Biomolecular Engineering, KAIST Institute for the Nanocentury (KINC), Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701 (Korea, Republic of); Lim, Kwon Taek, E-mail: ktlim@pknu.ac.kr [Department of Imaging System Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of)

2013-10-15

A novel approach for the synthesis of poly(glycidyl methacrylate) grafted CdSe quantum dot (QDs) (PGMA-g-CdSe) was developed. The PGMA-g-CdSe nanohybrids were synthesized by the surface-initiated atom transfer radical polymerization of glycidyl methacrylate from the surface of the strategic initiator, CdSe-BrIB QDs prepared by the interaction of 2-bromoisobutyryl bromide (BrIB) and CdSe-OH QDs. The structure, morphology, and optical property of the PGMA-g-CdSe nanohybrids were analyzed by FT-IR, XPS, TGA, XRD, TEM, and PL. The as-synthesized PGMA-g-CdSe nanohybrids having multi-epoxide groups were employed for the direct coupling of biotin via ring-opening reaction of the epoxide groups to afford the Biotin-f-PGMA-g-CdSe nanobioconjugate. The covalent immobilization of biotin onto PGMA-g-CdSe was confirmed by FT-IR, XPS, and EDX. Biocompatibility and imaging properties of the Biotin-f-PGMA-g-CdSe were investigated by MTT bioassay and PL analysis, respectively. The cell viability study suggested that the biocompatibility was significantly enhanced by the functionalization of CdSe QDs by biotin and PGMA.

Poly(glycidyl methacrylate) grafted CdSe quantum dots by surface-initiated atom transfer radical polymerization: Novel synthesis, characterization, properties, and cytotoxicity studies

International Nuclear Information System (INIS)

Bach, Long Giang; Islam, Md. Rafiqul; Lee, Doh Chang; Lim, Kwon Taek

2013-01-01

A novel approach for the synthesis of poly(glycidyl methacrylate) grafted CdSe quantum dot (QDs) (PGMA-g-CdSe) was developed. The PGMA-g-CdSe nanohybrids were synthesized by the surface-initiated atom transfer radical polymerization of glycidyl methacrylate from the surface of the strategic initiator, CdSe-BrIB QDs prepared by the interaction of 2-bromoisobutyryl bromide (BrIB) and CdSe-OH QDs. The structure, morphology, and optical property of the PGMA-g-CdSe nanohybrids were analyzed by FT-IR, XPS, TGA, XRD, TEM, and PL. The as-synthesized PGMA-g-CdSe nanohybrids having multi-epoxide groups were employed for the direct coupling of biotin via ring-opening reaction of the epoxide groups to afford the Biotin-f-PGMA-g-CdSe nanobioconjugate. The covalent immobilization of biotin onto PGMA-g-CdSe was confirmed by FT-IR, XPS, and EDX. Biocompatibility and imaging properties of the Biotin-f-PGMA-g-CdSe were investigated by MTT bioassay and PL analysis, respectively. The cell viability study suggested that the biocompatibility was significantly enhanced by the functionalization of CdSe QDs by biotin and PGMA.

Intensifying radiation induced grafting of 4-vinylpyridine/glycidyl methacrylate mixtures onto poly(ethylene-co-tetrafluoroethylene) films using ultrasound

International Nuclear Information System (INIS)

Nasef, Mohamed Mahmoud; Sithambaranathan, Paveswari; Ahmad, Arshad; Abouzari-lotf, Ebrahim

2017-01-01

A new ultrasound-aided method was used to enhance grafting of 4-vinylpyridine (4-VP) and glycidyl methacrylate (GMA) monomers mixtures onto electron beam (EB) irradiated poly(ethylene-co-tetrafluoroethylene) (ETFE) film for the first time. The effects of reaction parameters such as absorbed dose, monomer concentration, reaction time on both of degree of grafting (DG) and grafting efficiency (GE) were investigated under sonication and conventional grafting at similar temperatures. Fourier transform infrared (FTIR) and atomic force microscopy (AFM) were used to monitor the impact of the applied ultrasound on composition and surfaces of the grafted films whereas 1 H-NMR was used to investigate composition of the grafting residues. The ultrasound-aided grafting of 4-VP/GMA was found to enhance both of DG% and GE remarkably. Moreover, it produced grafted ETFE films having smoother surfaces without homopolymer contamination compared to grafted films obtained from conventional grafting. The results of this study suggest that the use of ultrasound is a promising way for intensifying grafting process and improving its economy. - Highlights: • Grafting of 4-VP/GMA onto ETFE films was carried out with the aid of ultrasound. • Degree of grafting was found to be strongly dependent on reaction parameters. • Sonication remarkably enhanced the reaction kinetics and grafting efficiency. • Grafted films with smoother surfaces without homopolymer contamination were obtained. • Ultrasound aided grafting is superior to conventional one and promotes intensification.

Bactericidal and Hemocompatible Coating via the Mixed-Charged Copolymer.

Science.gov (United States)

Fan, Xiao-Li; Hu, Mi; Qin, Zhi-Hui; Wang, Jing; Chen, Xia-Chao; Lei, Wen-Xi; Ye, Wan-Ying; Jin, Qiao; Ren, Ke-Feng; Ji, Jian

2018-03-28

Cationic antibacterial coating based on quaternary ammonium compounds, with an efficient and broad spectrum bactericidal property, has been widely used in various fields. However, the high density of positive charges tends to induce weak hemocompatibility, which hinders the application of the cationic antibacterial coating in blood-contacting devices and implants. It has been reported that a negatively charged surface can reduce blood coagulation, showing improved hemocompatibility. Here, we describe a strategy to combine the cationic and anionic groups by using mixed-charged copolymers. The copolymers of poly (quaternized vinyl pyridine- co- n-butyl methacrylate- co-methacrylate acid) [P(QVP- co- nBMA- co-MAA)] were synthesized through free radical copolymerization. The cationic group of QVP, the anionic group of MAA, and the hydrophobic group of nBMA were designed to provide bactericidal capability, hemocompatibility, and coating stability, respectively. Our findings show that the hydrophilicity of the copolymer coating increased, and its zeta potential decreased from positive charge to negative charge with the increase of the anionic/cationic ratio. Meanwhile, the bactericidal property of the copolymer coating was kept around a similar level compared with the pure quaternary ammonium copolymer coating. Furthermore, the coagulation time, platelet adhesion, and hemolysis tests revealed that the hemocompatibility of the copolymer coating improved with the addition of the anionic group. The mixed-charged copolymer combined both bactericidal property and hemocompatibility and has a promising potential in blood-contacting antibacterial devices and implants.

Influence of Maleic Anhydride/Glycidyl Methacrylate Cografted Polylactic Acid on Properties of Wood Flour/PLA Composites

Directory of Open Access Journals (Sweden)

DU Jun

2017-12-01

Full Text Available Graft copolymers of PLA-g-MAH, PLA-g-GMA and PLA-co-MAH/GMA were prepared by means of melt grafting. The structure of the graft copolymers were characterized by FTIR.Wood flour/PLA composites were prepared by injection molding with three kinds of graft copolymers as compatibilizers, and the fractured morphology of composites was investigated by scanning electron microscope (SEM. Results show that there is no obvious phase interface between wood flour and PLA,which indicating the interfacial compatibility of wood flour/PLA composites is improved after adding different graft copolymers. The determination results of mechanical properties, processing flowability and dynamic rheological property of composites prepared with different graft copolymers reveal that, compared to the composite without compatibilizer, the tensile strength and impact strength of wood flour/PLA composites are increased by 9.54% and 7.23% respectively, and the equilibrium torque, shear heat, storage modulus and complex viscosity are all increased after adding maleic anhydride/glycidyl methacrylate cografted polylactic acid.

Grafting of glycidyl methacrylate/styrene onto polyvinyldine fluoride membranes for proton exchange fuel cell

International Nuclear Information System (INIS)

Abdel-Hady, E.E.; El-Toony, M.M.; Abdel-Hamed, M.O.

2013-01-01

Simultaneous gamma irradiation was used effectively for grafting facilitation of glycidyl methacrylate (GMA) and styrene (Sty) onto polyvinylidine fluoride (PVDF). Grafting percent was 122 when monomers ratio are 30% Sty and 70% GMA at 20 KGy gamma irradiation dose. Characterization of the membrane was performed using FT-IR, ion exchange capacity (IEC), water uptake. Mechanical behavior such as tensile strength was studied while morphological structure of the membrane was carried out by scan electron microscope (SEM). The membrane with degree of grafting 122% showed higher IEC (1.2 m mol/cm) than those of Nafion membrane with corresponding proton conductivity of 5.7 × 10 −2 S/cm similar to it. Operating the fuel cell unit showed higher voltage of the prepared membranes than that of Nafion 211. The prepared membranes stability for 300 h work approved their applicability from the cost benefit point of view

Modification of macroporous membranes by graft co-polymerization induced by pre-irradiation with an electron accelerator

International Nuclear Information System (INIS)

Grasselli, M.; Yoshii, Fumio

1999-01-01

Glycidyl methacrylate (GMA) and N,N-dimethylacrylamide (DMAA) have been co-grafted on hollow fiber membranes of macroporous polyethylene. Grafted copolymers have been obtained with different ratios of the monomers (molar ratio between 0 and 2 DMAA/GMA). The properties of the modified membranes are studied

Magnetic poly(glycidyl methacrylate)-based microspheres prepared by suspension polymerization in the presence of modified La0.75Sr0.25MnO3 nanoparticles

Czech Academy of Sciences Publication Activity Database

Horák, Daniel; Pollert, Emil; Trchová, Miroslava; Kovářová, Jana

2009-01-01

Roč. 45, č. 4 (2009), s. 1009-1016 ISSN 0014-3057 R&D Projects: GA AV ČR 1QS100100553; GA AV ČR KAN200200651 Institutional research plan: CEZ:AV0Z40500505; CEZ:AV0Z10100521; CEZ:AV0Z1010921 Keywords : glycidyl methacrylate * perovskite * magnetic Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.310, year: 2009

Densities, isobaric thermal compressibilities and derived thermodynamic properties of the binary systems of cyclohexane with allyl methacrylate, butyl methacrylate, methacrylic acid, and vinyl acetate at t = (298.15 and 308.15) K

Energy Technology Data Exchange (ETDEWEB)

Wisniak, Jaime [Department of Chemical Engineering, Ben-Gurion University of the Negev, Beer-Sheva 84105 (Israel)]. E-mail: wisniak@bgumail.bgu.ac.il; Peralta, Rene D. [Centro de Investigacion en Quimica Aplicada, Saltillo 25100, Coahuila (Mexico); Infante, Ramiro [Centro de Investigacion en Quimica Aplicada, Saltillo 25100, Coahuila (Mexico); Cortez, Gladis [Centro de Investigacion en Quimica Aplicada, Saltillo 25100, Coahuila (Mexico); Lopez, R.G. [Centro de Investigacion en Quimica Aplicada, Saltillo 25100, Coahuila (Mexico)

2005-10-15

Densities of the binary systems of cyclohexane with allyl methacrylate, butyl methacrylate, methacrylic acid, and vinyl acetate have been measured as a function of the composition, at 298.15 and 308.15 K and atmospheric pressure, using an Anton Paar DMA 5000 oscillating U-tube densimeter. The calculated excess molar volumes were correlated with the Redlich-Kister equation and with a series of Legendre polynomials. The excess molar volumes are positive for the four binaries studied. Within the short temperature range considered here the coefficient of thermal expansion is positive for all the systems studied; it varies only slightly with the nature of the acrylate except for the system cyclohexane + vinyl acetate.

Cyto- and genotoxicological assessment and functional characterization of N-vinyl-2-pyrrolidone-acrylic acid-based copolymeric hydrogels with potential for future use in wound healing applications

International Nuclear Information System (INIS)

Kirf, Dominik; Devery, Sinead M; Higginbotham, Clement L; Rowan, Neil J

2010-01-01

This study investigated the toxicity of N-vinyl-2-pyrrolidone-acrylic acid copolymer hydrogels crosslinked with ethylene glycol dimethacrylate or poly(ethylene glycol) dimethacrylate. There is a pressing need to establish the toxicity status of these new copolymers because they may find applications in future wound healing processes. Investigations revealed that the capacity of these hydrogels for swelling permitted the retention of high amounts of water yet still maintaining structural integrity. Reverse phase HPLC analysis suggested that unreacted monomeric base material was efficiently removed post-polymerization by applying an additional purification process. Subsequently, in vitro toxicity testing was performed utilizing direct and indirect contact exposure of the polymers to human keratinocytes (HaCaT) and human hepatoma (HepG2) cells. No indication of significant cell death was observed using the established MTT, neutral red (NR) and fluorescence-based toxicity endpoint indicators. In addition, the alkaline Comet assay showed no genotoxic effects following cell exposure to hydrogel extracts. Investigations at the nucleotide level using the Ames mutagenicity assay demonstrated no evidence of mutagenic activity associated with the polymers. Findings from this study demonstrated that these hydrogels are non-cytotoxic and further work can be carried out to investigate their potential as a wound-healing device that will impact positively on patient health and well-being.

Cyto- and genotoxicological assessment and functional characterization of N-vinyl-2-pyrrolidone-acrylic acid-based copolymeric hydrogels with potential for future use in wound healing applications

Energy Technology Data Exchange (ETDEWEB)

Kirf, Dominik; Devery, Sinead M [Department of Life and Physical Science, Athlone Institute of Technology (Ireland); Higginbotham, Clement L [Materials Research Institute, Athlone Institute of Technology (Ireland); Rowan, Neil J, E-mail: sdevery@ait.i, E-mail: dkirf@ait.i, E-mail: chigginbotham@ait.i, E-mail: nrowan@ait.i [Department of Nursing and Health Science, Athlone Institute of Technology (Ireland)

2010-06-01

This study investigated the toxicity of N-vinyl-2-pyrrolidone-acrylic acid copolymer hydrogels crosslinked with ethylene glycol dimethacrylate or poly(ethylene glycol) dimethacrylate. There is a pressing need to establish the toxicity status of these new copolymers because they may find applications in future wound healing processes. Investigations revealed that the capacity of these hydrogels for swelling permitted the retention of high amounts of water yet still maintaining structural integrity. Reverse phase HPLC analysis suggested that unreacted monomeric base material was efficiently removed post-polymerization by applying an additional purification process. Subsequently, in vitro toxicity testing was performed utilizing direct and indirect contact exposure of the polymers to human keratinocytes (HaCaT) and human hepatoma (HepG2) cells. No indication of significant cell death was observed using the established MTT, neutral red (NR) and fluorescence-based toxicity endpoint indicators. In addition, the alkaline Comet assay showed no genotoxic effects following cell exposure to hydrogel extracts. Investigations at the nucleotide level using the Ames mutagenicity assay demonstrated no evidence of mutagenic activity associated with the polymers. Findings from this study demonstrated that these hydrogels are non-cytotoxic and further work can be carried out to investigate their potential as a wound-healing device that will impact positively on patient health and well-being.

Study on grafting glycidyl methacrylate onto HDPE membranes by pre-irradiation graft copolymerization

International Nuclear Information System (INIS)

Tong Long; Zu Jianhua; Liu Xinwen; Sun Guisheng; Yu Chunhui

2006-01-01

Glycidyl methacrylate (GMA) was grafted onto HDPE membranes by pre-irradiation method with 1.8 MeV E-beam and a kind of membranes having reactive epoxy groups was successfully synthesized. Effects of monomer concentration, reaction temperature and time and irradiation dose on the grafting yield were studied. Composition, thermo-property and surface morphology of the grafted membranes were studied by FTIR, DSC and Tapping-mode AFM, respectively. The FTIR measurements proved the synthesized copolymer is HDPE-g-GMA. The DSC results indicated the grafted HDPE's melting temperature (T m ) and heat of fusion (ΔH f ( HDPE) ) which was reduced with increasing grafting yield. The AFM images indicated that surface of the HDPE-g-GMA membranes was rougher than the virgin HDPE. (authors)

Method for the production of a hydrophilic polymer product

International Nuclear Information System (INIS)

Cordrey, P.W.; Frankland, J.D.; Highgate, D.J.

1976-01-01

It has been found that by subjecting mixtures containing hydrophilic monomer materials to radiation it is possible to obtain polymers capable of absorbing up to five times or more their weight of water. These polymers are very suitable for use in contact with living tissue since they contain none of the harmful contaminants derived from initiators used in conventional polymerisation. A method for the production of these polymers comprises subjecting to irradiation polymerisation a mixture containing (1) at least one hydrophilic monomer selected from N-vinyl pyrrolidones and hydroxyalkyl methacrylates and at least one hydrophobic monomer selected from alkyl acrylates, alkyl methacrylates and styrene, or (2) at least one hydrophilic monomer such as N-vinyl-2-pyrrolidone or hydroxyethyl methacrylate and at least one hydrophobic polymer selected from nylons, polyamides and terephthalic acid, with one or more alkyl substituted hexamethylene diamines, polyalkyl acrylates, polyalkyl methacrylates, polystyrenes, polyvinyl chloride and bisphenol polycarbonate. The irradiation may be gamma-ray, and the dosage 2 to 5 MR over one to 48 hours. The polymerisation may be carried out in the presence of a cross-linking agent such as alkyl methacrylate, divinylbenzene, or ethylene glycol dimethacrylate and in an oxygen-free or inert atmosphere, or in vacuo. Examples of application of the method are given. (U.K.)

Photoinitiated Polymerization-Induced Self-Assembly of Glycidyl Methacrylate for the Synthesis of Epoxy-Functionalized Block Copolymer Nano-Objects.

Science.gov (United States)

Tan, Jianbo; Liu, Dongdong; Huang, Chundong; Li, Xueliang; He, Jun; Xu, Qin; Zhang, Li

2017-08-01

Herein, a novel photoinitiated polymerization-induced self-assembly formulation via photoinitiated reversible addition-fragmentation chain transfer dispersion polymerization of glycidyl methacrylate (PGMA) in ethanol-water at room temperature is reported. It is demonstrated that conducting polymerization-induced self-assembly (PISA) at low temperatures is crucial for obtaining colloidal stable PGMA-based diblock copolymer nano-objects. Good control is maintained during the photo-PISA process with a high rate of polymerization. The polymerization can be switched between "ON" and "OFF" in response to visible light. A phase diagram is constructed by varying monomer concentration and degree of polymerization. The PGMA-based diblock copolymer nano-objects can be further cross-linked by using a bifunctional primary amine reagent. Finally, silver nanoparticles are loaded within cross-linked vesicles via in situ reduction, exhibiting good catalytic properties. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Thin-film type Li-ion battery, using a polyethylene separator grafted with glycidyl methacrylate

International Nuclear Information System (INIS)

Ko, J.M.; Min, B.G.; Kim, D.-W.; Ryu, K.S.; Kim, K.M.; Lee, Y.G.; Chang, S.H.

2004-01-01

For the improvement of organic electrolyte holding ability, the hydrophobic surface of a porous polyethylene (PE)-membrane separator was modified by grafting a hydrophilic monomer, glycidyl methacrylate (GMA), PE-g-GMA, by using electron beam technology, and applied to a thin film type Li-ion battery to elucidate the effect of a surface modification of a PE membrane separator on the cyclic life of Li-ion batteries. The Li-ion battery using the PE-g-GMA membrane separator showed a better cycle life than that of the unmodified PE membrane separator, indicating that the surface hydrophilicity of the PE membrane separator improved the electrolyte holding capability between the electrodes in the Li-ion cell and prevented the electrolyte leakage

Immunocapture of CD133-positive cells from human cancer cell lines by using monodisperse magnetic poly(glycidyl methacrylate) microspheres containing amino groups

Energy Technology Data Exchange (ETDEWEB)

Kuan, Wei-Chih [Department of Chemical Engineering, Systems Biology and Tissue Engineering Research Center, National Chung Cheng University, Minhisung 621, Taiwan (China); Horák, Daniel, E-mail: horak@imc.cas.cz [Institute of Macromolecular Chemistry, Academy of Sciences of the Czech Republic, Heyrovsky Sq. 2, 162 06 Prague 6 (Czech Republic); Plichta, Zdeněk [Institute of Macromolecular Chemistry, Academy of Sciences of the Czech Republic, Heyrovsky Sq. 2, 162 06 Prague 6 (Czech Republic); Lee, Wen-Chien [Department of Chemical Engineering, Systems Biology and Tissue Engineering Research Center, National Chung Cheng University, Minhisung 621, Taiwan (China)

2014-01-01

Magnetic poly(glycidyl methacrylate)-based macroporous microspheres with an average particle size of 4.2 μm were prepared using a modified multi-step swelling polymerization method and by introducing amino functionality on their surfaces. Antibody molecules were oxidized on their carbohydrate moieties and bound to the amino-containing magnetic microspheres via a site-directed procedure. CD133-positive cells could be effectively captured from human cancer cell lines (HepG2, HCT116, MCF7, and IMR-32) by using magnetic microspheres conjugated to an anti-human CD133 antibody. After further culture, the immunocaptured CD133-expressing cells from IMR-32 proliferated and gradually detached from the magnetic microspheres. Flow-cytometric analysis confirmed the enrichment of CD133-expressing cells by using the antibody-bound magnetic microspheres. Such microspheres suitable for immunocapture are very promising for cancer diagnosis because the CD133-expressing cells in cancer cell lines have been suggested to be cancer stem cells. - Highlights: • Multi-step swelling polymerization produced poly(glycidyl methacrylate) microspheres. • Anti-human CD133 antibodies were bound to the amino-containing magnetic microspheres. • CD133-positive cells were effectively captured from human cancer cell lines. • Immunocaptured CD133-expressing cells proliferated and were detached from microspheres. • Enrichment of CD133-expressing cells was confirmed by flow-cytometric analysis.

Poly(vinyl pyrrolidone)-Chitosan implant for endoscopic treatment of vesicoureteral reflux

International Nuclear Information System (INIS)

Relleve, Lorna S.; Abad, Lucille V.; Aranilla, Charito T.; Dela Rosa, A.M.; Bolong, David T.; Bisnar, Carlo C.

2008-01-01

Radiation-crosslinked poly(vinyl pyrrolidone) (PVP)-Chitosan was prepared as a potential injectable implant for endoscopic treatment of vesicoureteral reflux (VUR). The physical and histological properties of PVP-Chitosan implant in comparison with the commercial dextranomer/hyaluronic acid copolymer (Deflux) have been evaluated in vivo by subcutaneous and abdominal injection in rats over a period of 6 months. The PVP-Chitosan implant was easily injected through 26-gauge needle. Monthly gross examination of the implanted sites showed no significant decrease in volume of implant and no local inflammatory reaction. Histological findings indicated no evidence of migration to the distant organs after 6 months of implantation. Results of this study indicated that PVP-Chitosan implant has properties of a good tissue augmenting substance such as stability, biocompatibility and non-migration but long-term studies are needed to evaluate its therapeutic efficiency. (author)

Syntheses of amine-type adsorbents with emulsion graft polymerization of glycidyl methacrylate

International Nuclear Information System (INIS)

Seko, N.; Bang, L.T.; Tamada, M.

2007-01-01

Glycidyl methacrylate (GMA) which was precursor monomer for the synthesis of metal ion adsorbent was emulsified by surfactant of Tween 20 (Tw-20). The emulsion of 5% GMA in the water was stable for 48 h at Tw-20 concentration of 0.5%. Graft polymerization of GMA on polyethylene fiber was carried out in the emulsion state at various pre-irradiation doses. Degree of grafting (Dg) reached 103%, 301% and 348% for 1 h grafting at 40 deg. C with pre-irradiation of 10, 30 and 40 kGy, respectively. But the Dg was depressed when the pre-irradiation dose was over 50 kGy since cross-linking occurred simultaneously in the trunk polymer. Dg decreased with increment of Tw-20 concentration in emulsion of 5% GMA at pre-irradiation of 40 kGy. The three kinds of amine-type adsorbents were synthesized by reacting diethylenetriamine (DETA), triethylenetetramine (TETA) and ethylenediamine (EDA) with GMA-grafted polyethylene fiber. The synthesized EDA-type adsorbent had the highest selectivity against U ion and the distribution coefficient was 2.0 x 10 6

Ring-opening metathesis polymerization based pore-size-selective functionalization of glycidyl methacrylate based monolithic media: access to size-stable nanoparticles for ligand-free metal catalysis.

Science.gov (United States)

Bandari, Rajendar; Höche, Thomas; Prager, Andrea; Dirnberger, Klaus; Buchmeiser, Michael R

2010-04-19

Monolithic polymeric supports have been prepared by electron-beam-triggered free-radical polymerization using a mixture of glycidyl methacrylate and trimethylolpropane triacrylate in 2-propanol, 1-dodecanol, and toluene. Under appropriate conditions, phase separation occurred, which resulted in the formation of a porous monolithic matrix that was characterized by large (convective) pores in the 30 μm range as well as pores of 7 nm were hydrolyzed by using poly(styrenesulfonic acid) (Mw = 69,400 g mol(-1), PDI=2.4). The remaining epoxy groups inside pores of nanoparticles 2 nm in diameter were formed. The palladium-nanoparticle-loaded monoliths were used in both Heck- and Suzuki-type coupling reactions achieving turnover numbers of up to 167,000 and 63,000, respectively. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

AFM study of the morphologic change of HDPE surface photografted with glycidyl methacrylate.

Science.gov (United States)

Wang, Huiliang; Han, Jianmei

2009-05-01

The UV-induced grafting of glycidyl methacrylate (GMA) onto high-density polyethylene (HDPE) and the atomic force microscopy (AFM) study of the morphologic change of the grafted surface are reported. The grafting was carried out in GMA acetone solutions with different monomer concentrations. Grafting was much faster in a solution with a higher monomer concentration. FTIR analyses proved that GMA had been successfully grafted onto HDPE. The morphologies of grafted HDPE surfaces changed with UV irradiation time. The monomer concentration had a significant effect on the morphologies of the grafted HDPE surfaces. The HDPE surface grafted in a solution with a higher monomer concentration was much rougher than that grafted in a solution with a lower monomer concentration. The growth models of the grafted granules or clusters are also proposed.

Copolymerization parameters of N-Methacryloyloxy tetrabromophthalimide with different vinyl monomers

International Nuclear Information System (INIS)

Mahmoud, A.A.

2005-01-01

N-Methacryloyloxytetrabromophthalimide (NMTP) was synthesized by the reaction of N-hydroxytetrabromophthalimide with either methacryloyl chloride or methacrylic acid in the presence of triethylamine or N, Ndicyclohexylcarbodiimide respectively. Binary copolymerization reactions of the prepared monomer with ethyl acrylate (EA), n-butyl methacrylate (n.BMA), tertiary butylacrylate (t.BA) and vinyl acetate (VA) were performed in methylene chloride at 65 degree C using 1 mol % azobisisobutylronitrile (AIBN) as initiator. The structure of the prepared monomer was investigated by IR and 1H NMR spectroscopy. The copolymer compositions were determined from bromine analysis. Copolymerization parameters for each system were calculated by the Fineman-Ross and Kelen-Tudos methods. The monomer reactivity ratios for the systems NMTP-EA, NMTP-n.BMA, NMTP-t.BA and NMTP-VA were found to be r1 0.180, r2 = 0.893, r1 = 0.025, r2 = 0.680, r1 0.014, r2 0.956 and r1 1.002, r2 1.004 respectively

In vivo genotoxicity assessment of acrylamide and glycidyl methacrylate.

Science.gov (United States)

Dobrovolsky, Vasily N; Pacheco-Martinez, M Monserrat; McDaniel, L Patrice; Pearce, Mason G; Ding, Wei

2016-01-01

Acrylamide (ACR) and glycidyl methacrylate (GMA) are structurally related compounds used for making polymers with various properties. Both chemicals can be present in food either as a byproduct of processing or a constituent of packaging. We performed a comprehensive evaluation of ACR and GMA genotoxicity in Fisher 344 rats using repeated gavage administrations. Clastogenicity was measured by scoring micronucleated (MN) erythrocytes from peripheral blood, DNA damage in liver, bone marrow and kidneys was measured using the Comet assay, and gene mutation was measured using the red blood cell (RBC) and reticulocyte Pig-a assay. A limited histopathology evaluation was performed in order to determine levels of cytotoxicity. Doses of up to 20 mg/kg/day of ACR and up to 250 mg/kg/day of GMA were used. ACR treatment resulted in DNA damage in the liver, but not in the bone marrow. While ACR was not a clastogen, it was a weak (equivocal) mutagen in the cells of bone marrow. GMA caused DNA damage in the cells of bone marrow, liver and kidney, and induced MN reticulocytes and Pig-a mutant RBCs in a dose-dependent manner. Collectively, our data suggest that both compounds are in vivo genotoxins, but the genotoxicity of ACR is tissue specific. Published by Elsevier Ltd.

Study of chemical interaction induced by ionizing radiation poly(dimethylsiloxane-g-ethylene oxide) in the poly(n-vinyl-2-pyrrolidone) and agar membrane; Estudo da interacao quimica do poli(dimetilsiloxano-g-oxido de etileno) na membrana de poli(n-vinil-2-pirrolidona) e agar induzida com radiacao ionizante

Energy Technology Data Exchange (ETDEWEB)

Bazzi, Aurea de Souza

1999-07-01

Membrane composed by poly(N-vinyl-2-pyrrolidone) (PVP) and agar was formulated with and without poly(dimethylsiloxane-g-ethylene oxide) (SEO) irradiated with electron beam with doses between 10-50 kGy. The radiolytic behaviour of each component, PVP, agar and SEO, was studied when irradiated by gamma ray, in the absence and presence of air and water, by electron paramagnetic resonance (EPR) at 77 K. The chemical interaction of SEO with PVP/agar membrane was investigated by: infrared spectroscopy, energy dispersive X-ray fluorescence, dynamic-mechanical analysis, scanning electron microscopy, gel and swelling analysis. The cytotoxicity of the PVP/agar/SEO membrane was evaluated by cellular suppression. The membrane radicals from PVP ({phi}NC.) and from water (H., OH. and H{sub 2}O) was observed by EPR at 77K. The agar radicals formed by hydrogen abstraction of C{sub 1} and C{sub 3} of {beta}-D-galactose and/or C{sub 1} and C{sub 4} of {alpha}-L-galactose, reacted primarily with water radicals in despite of they also took part in the membrane by chemical bond. The radicals from SEO (.CH{sub 2}{approx}, .Si{approx}, .O{approx}) participated in the inter and intramolecular crosslinking as co-crosslinker by polymeric bridge. The co-crosslinked action depended on its concentration associated to PVP concentration. The presence op acrylates increases the tensile break of the PVP/agar/SEO membrane significantly. (author)

Phase behavior for the poly(alkyl methacrylate)+supercritical CO2+DME mixture at high pressures

International Nuclear Information System (INIS)

Choi, Yong-Seok; Chio, Sang-Won; Byun, Hun-Soo

2016-01-01

The phase behavior curves of binary and ternary system were measured for poly(alkyl methacrylate) in supercritical CO 2 , as well as for the poly(alkyl methacrylate)+dimethyl ether (DME) (or 1-butene) in CO 2 . The solubility curves are reported for the poly(alkyl methacrylate)+DME in supercritical CO 2 at temperature from (300 to 465) K and a pressure from (3.66 to 248) MPa. Also, The high-pressure static-type apparatus of cloud-point curve was tested by comparing the measured phase behavior data of the poly(methyl methacrylate) [PMMA]+CO 2 +20.0 and 30.4 wt% methyl methacrylate (MMA) system with literature data of 10.4, 28.8 and 48.4 wt% MMA concentration. The phase behavior data for the poly(alkyl methacrylate)+CO 2 +DME mixture were measured in changes of the pressure-temperature (p, T) slope and with DME concentrations. Also, the cloud-point pressure for the poly(alkyl methacrylate)+1- butene solution containing supercritical CO 2 shows from upper critical solution temperature (UCST) region to lower critical solution temperature (LCST) region at concentration range from (0.0 to 95) wt% 1-butene at below 455 K and at below 245MPa.

Equilibrium and kinetics study on hexavalent chromium adsorption onto diethylene triamine grafted glycidyl methacrylate based copolymers

International Nuclear Information System (INIS)

Maksin, Danijela D.; Nastasović, Aleksandra B.; Milutinović-Nikolić, Aleksandra D.; Suručić, Ljiljana T.; Sandić, Zvjezdana P.; Hercigonja, Radmila V.; Onjia, Antonije E.

2012-01-01

Highlights: ► Methacrylate based copolymers grafted with diethylene triamine as Cr(VI) sorbents. ► Chemisorption and pore diffusion are characteristics of this sorption system. ► Langmuir isotherm provided best fit and maximum adsorption capacity was 143 mg g −1 . ► Cr(VI) sorption onto amino-functionalized copolymer was endothermic and spontaneous. ► A simple, efficient and cost-effective hexavalent chromium removal method. - Abstract: Two porous and one non-porous crosslinked poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) [abbreviated PGME] were prepared by suspension copolymerization and functionalized with diethylene triamine [abbreviated PGME-deta]. Samples were characterized by elemental analysis, mercury porosimetry, scanning electron microscopy with energy-dispersive X-ray spectroscopy, and transmission electron microscopy. Kinetics of Cr(VI) sorption by PGME-deta were investigated in batch static experiments, in the temperature range 25–70 °C. Sorption was rapid, with the uptake capacity higher than 80% after 30 min. Sorption behavior and rate-controlling mechanisms were analyzed using five kinetic models (pseudo-first order, pseudo-second order, Elovich, intraparticle diffusion and Bangham model). Kinetic studies showed that Cr(VI) adsorption adhered to the pseudo-second-order model, with definite influence of pore diffusion. Equilibrium data was tested with Langmuir, Freundlich and Tempkin adsorption isotherm models. Langmuir model was the most suitable indicating homogeneous distribution of active sites on PGME-deta and monolayer sorption. The maximum adsorption capacity from the Langmuir model, Q max , at pH 1.8 and 25 °C was 143 mg g −1 for PGME2-deta (sample with the highest amino group concentration) while at 70 °C Q max reached the high value of 198 mg g −1 . Thermodynamic parameters revealed spontaneous and endothermic nature of Cr(VI) adsorption onto PGME-deta.

Preparation of anti-CD4 monoclonal antibody-conjugated magnetic poly(glycidyl methacrylate) particles and their application on CD4+ lymphocyte separation.

Science.gov (United States)

Pimpha, Nuttaporn; Chaleawlert-umpon, Saowaluk; Chruewkamlow, Nuttapol; Kasinrerk, Watchara

2011-03-15

Novel immunomagnetic particles have been prepared for separation of CD4(+) lymphocytes. The magnetic nanoparticles with a diameter of approximately 5-6 nm were first synthesized by co-precipitation from ferrous and ferric iron solutions and subsequently encapsulated with poly(glycidyl methacrylate) (PGMA) by precipitation polymerization. Monoclonal antibody specific to CD4 molecules expressed on CD4(+) lymphocytes was conjugated to the surface of magnetic PGMA particles through covalent bonding between epoxide functional groups on the particle surface and primary amine groups of the antibodies. The generated immunomagnetic particles have successfully separated CD4(+) lymphocytes from whole blood with over 95% purity. The results indicated that these particles can be employed for cell separation and provide a strong potential to be applied in various biomedical applications including diagnosis, and monitoring of human diseases. Copyright © 2010 Elsevier B.V. All rights reserved.

Synthesis and characterization of monosize magnetic poly(glycidyl methacrylate) beads

Institute of Scientific and Technical Information of China (English)

Evrim Banu Alt1nta(s); Lokman Uzun; Adil Denizli

2007-01-01

Monosize, 1.6 μm, magnetic beads of poly(glycidyl methacrylate) [M-poly(GMA)], were prepared by dispersion polymerization in the presence of Fe3O4 nano-powder. Monosize M-poly(GMA) beads were characterized by swelling tests, density measurements, electron spin resonance (ESR), vibrating sample magnetometer (VSM) and scanning electron microscopy (SEM). The characteristic functional groups of M-poly(GMA)beads were analyzed by Fourier transform infrared spectrometer (FTIR). The M-poly(GMA) beads are highly uniform in size and have a spherical shape and non-porous structure. Polydispersity index (PDI) of M-poly(GMA) beads was calculated to be around 1.008. The hydrated density of the M-poly(GMA) beads measured at 25 ℃ was 1.14 g/cm3. The content of oxirane groups on the surface of the M-poly(GMA) sample was found to be 3.46 mmol/g by using perchloric acid titration. The specific surface area of the M-poly(GMA) beads was determined to be 3.2 m2/g.The equilibrium swelling ratio was 52%. The volume fraction of magnetite nanopowder in the M-poly(GMA) beads was found to be 4.5%. The g factor, that can be considered as a quantity characteristic of the molecules in which the unpaired electrons are located, was found to be 2.28for M-poly(GMA). The external magnetic field at resonance was calculated to be 2055 Gs which was found sufficient to excite all of the dipole moments present in 1.0 g of M-poly(GMA) sample.

Gelation of photopolymerized hyaluronic acid grafted with glycidyl methacrylate

International Nuclear Information System (INIS)

Prado, S.S.; Weaver, J.M.; Love, B.J.

2011-01-01

Experiments have tracked the ambient gelation of a series of hydrophilic hyaluronic acid (HA) resins grafted with glycidyl methacrylate (GM) and photopolymerized as a function of dose. The resin mixtures range in GMHA concentration between 0.5 and 1.5% w/w in phosphate buffered saline (PBS). Illuminated at 20 mW/cm 2 , the dynamic viscosity (η(t)) has been tracked and characterized using the Boltzmann log-sigmoidal model. A gelled viscosity of ∼ 10 Pa s was determined at 0.5% w/w which rose to ∼ 50 Pa s at or above 1% w/w. More curing agent marginally increased the gel viscosity at each concentration. Time constants associated with viscosity advancement were shortest at [GMHA] = 1.0%; higher concentrations are attributed with lower quantum efficiency when illuminated. Subsequent frequency sweeps replicated already published work using similar GHMA concentrations in PBS. G' values ranged from 100 to 500 Pa over the formulation range with expected sensitivity to GMHA and curing agent concentration. Overall, the sigmoidal model represented this advancing viscosity data well, and further analysis of the physical significance of these model parameters may help in understanding photopolymerization of this complicated formulation more broadly. Highlights: → The ambient dynamic viscosity of photopolymerized GMHA gels has been measured. → 2 physical parameters and two time constants were extracted from the sigmoidal model. → Higher crosslinker content for a fixed GMHA concentration led to higher gel viscosity. → The time to toggle between the initial and final viscosity ranged between 5 and 10 s. → Dynamic frequency sweep tests on cured gels also revealed G' values between 100 and 500 Pa.

Modification of macroporous membranes by graft co-polymerization induced by pre-irradiation with an electron accelerator; Modificacion de membranas macroporosas para la recuperacion de protemas por intercambio ionico

Energy Technology Data Exchange (ETDEWEB)

Grasselli, M [Buenos Aires Univ. (Argentina). Facultad de Farmacia y Bioquimica; Yoshii, Fumio [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

1999-07-01

Glycidyl methacrylate (GMA) and N,N-dimethylacrylamide (DMAA) have been co-grafted on hollow fiber membranes of macroporous polyethylene. Grafted copolymers have been obtained with different ratios of the monomers (molar ratio between 0 and 2 DMAA/GMA). The properties of the modified membranes are studied.

Replacement of Poly(vinyl pyrrolidone) by Thiols: A Systematic Study of Ag Nanocube Functionalization by Surface-Enhanced Raman Scattering.

Science.gov (United States)

Moran, Christine H; Rycenga, Matthew; Zhang, Qiang; Xia, Younan

2011-11-10

In this work, we used surface-enhanced Raman scattering (SERS) to monitor the replacement of poly(vinyl pyrrolidone) (PVP) on Ag nanocubes by cysteamine, thiol-terminated PEG, and benzenedithiol. PVP is widely used as a colloidal stabilizer and capping agent to control the shape of Ag (as well as many other noble metals) nanocrystals during synthesis, and to stabilize the final colloidal suspension. However, the surface chemistry of Ag nanocrystals often needs to be tailored for specific applications, so the PVP coating must be removed and/or replaced by other ligands. By monitoring the signature peak from the carbonyl groups of PVP, we show, for the first time, that the PVP adsorbed on the surface of Ag nanocubes was completely replaced by the thiol molecules at room temperature over the course of a few hours. We observed the same trend no matter if the Ag nanocubes were suspended in an aqueous solution of the thiol or supported on a silicon substrate and then immersed in the thiol solution.

Controlled grafting of vinylic monomers on polyolefins: a robust mathematical modeling approach.

Science.gov (United States)

Saeb, Mohammad Reza; Rezaee, Babak; Shadman, Alireza; Formela, Krzysztof; Ahmadi, Zahed; Hemmati, Farkhondeh; Kermaniyan, Tayebeh Sadat; Mohammadi, Yousef

2017-01-01

Experimental and mathematical modeling analyses were used for controlling melt free-radical grafting of vinylic monomers on polyolefins and, thereby, reducing the disturbance of undesired cross-linking of polyolefins. Response surface, desirability function, and artificial intelligence methodologies were blended to modeling/optimization of grafting reaction in terms of vinylic monomer content, peroxide initiator concentration, and melt-processing time. An in-house code was developed based on artificial neural network that learns and mimics processing torque and grafting of glycidyl methacrylate (GMA) typical vinylic monomer on high-density polyethylene (HDPE). Application of response surface and desirability function enabled concurrent optimization of processing torque and GMA grafting on HDPE, through which we quantified for the first time competition between parallel reactions taking place during melt processing: (i) desirable grafting of GMA on HDPE; (ii) undesirable cross-linking of HDPE. The proposed robust mathematical modeling approach can precisely learn the behavior of grafting reaction of vinylic monomers on polyolefins and be placed into practice in finding exact operating condition needed for efficient grafting of reactive monomers on polyolefins.

Study on CO2/ N2 separation: the effect of rubbery polymer coating on PVDF membrane

Science.gov (United States)

Zuwairi, M. Z.; Rahman, S. A.

2017-06-01

The emission of harmful gases such as carbon dioxide (CO2) via gas processing plant and daily human activities gave negative impacts to the environment and global inhabitant. Flat sheet asymmetric membranes were produced from homogenous solution of Poly(vinylideneflouride) (PVDF) via phase inversion method using N-methyl-2-pyrrolidone (NMP) as the solvent. While the poly ether b-amide (PEBAX) was dissolve by using of (70 ethanol and 30 water) as a solvent and and lithium chloride as a additives. The morphology and cross section of the produced membranes were observed by Scanning Electron Microscope (SEM). Then, the membranes were tested for chemical analysis to define the presence of PEBAX in the membrane by using Fourier Transform Infrared (FTIR) spectroscopy. The permeation performances of the membranes were evaluated in terms of permeability and selectivity of the membranes by using gas permeation test. Increasing the PEBAX content significantly increased the selectivity of the PVDF membrane to separate the CO2/N2 gases but decreased the amount of the gases that passed through the membrane.

The characterization of wound dressing poly (vinyl pyrrolidone) hydrogels using gamma radiation

Energy Technology Data Exchange (ETDEWEB)

Rezende, Talita C.; Pinheiro, Christiano J.G., E-mail: talitacolombi@yahoo.com, E-mail: christrieste@yahoo.it [Universidade Federal do Espirito Santo (CCA/UFES), Alegre, ES (Brazil). Programa de Pós-Graduação em Engenharia Química; Paula, Heberth D., E-mail: hdpaula@gmail.com [Universidade Federal do Espirito Santo, Alegre (UFES), ES (Brazil). Departamento de Farmácia; Morais, Pedro A.B., E-mail: pedmora2005@gmail.com [Universidade Federal do Espirito Santo (UFES), Alegre, ES (Brazil). Departamento de Química

2017-07-01

The first hydrogel for wound dressing processed by radiation was developed in Poland in 1986 by the inventor Janusz M. Rosiak and reached the local market in 1992. Laboratories of developing countries, which face all kinds of restrictions, were seduced by the simplicity of the process and low cost of its raw materials. It was a technological breakthrough due to its painless product characteristics and having improved healing properties such as absorbing a high water capacity, attached to healthy skin, and being easy to remove, plus its intelligent production process combining sterilization and crosslinking in a simultaneous operation. The use of hydrogels as biomaterials has increased recently. Hydrogel wound dressings were prepared using the gamma ray irradiation technique. Radiation was applied as a tool for crosslinking and sterilization of these materials. The hydrogels are composed of poly (N-vinyl-2-pyrrolidone) (PVP), poly (ethylene glycol) (PEG) and agar at radiation doses of 15, 20, 25, 30 kGy. The influence of some process parameters on their properties was investigated by: sterilization, gel fraction, swelling measures and mechanical properties. Hydrogels with less than 20 kGy of radiation were not properly sterilized. The gel fraction and swelling increased with increasing radiation dose due to increased crosslinking density, and at 25kGy, obtained optimum swelling. No significant differences were found for the test of mechanical properties but hydrogel matrices of different doses of gamma radiation. (author)

The characterization of wound dressing poly (vinyl pyrrolidone) hydrogels using gamma radiation

International Nuclear Information System (INIS)

Rezende, Talita C.; Pinheiro, Christiano J.G.; Paula, Heberth D.; Morais, Pedro A.B.

2017-01-01

The first hydrogel for wound dressing processed by radiation was developed in Poland in 1986 by the inventor Janusz M. Rosiak and reached the local market in 1992. Laboratories of developing countries, which face all kinds of restrictions, were seduced by the simplicity of the process and low cost of its raw materials. It was a technological breakthrough due to its painless product characteristics and having improved healing properties such as absorbing a high water capacity, attached to healthy skin, and being easy to remove, plus its intelligent production process combining sterilization and crosslinking in a simultaneous operation. The use of hydrogels as biomaterials has increased recently. Hydrogel wound dressings were prepared using the gamma ray irradiation technique. Radiation was applied as a tool for crosslinking and sterilization of these materials. The hydrogels are composed of poly (N-vinyl-2-pyrrolidone) (PVP), poly (ethylene glycol) (PEG) and agar at radiation doses of 15, 20, 25, 30 kGy. The influence of some process parameters on their properties was investigated by: sterilization, gel fraction, swelling measures and mechanical properties. Hydrogels with less than 20 kGy of radiation were not properly sterilized. The gel fraction and swelling increased with increasing radiation dose due to increased crosslinking density, and at 25kGy, obtained optimum swelling. No significant differences were found for the test of mechanical properties but hydrogel matrices of different doses of gamma radiation. (author)

Application of magnetic poly(styrene-glycidyl methacrylate) microspheres for immunomagnetic separation of bone marrow cells

Energy Technology Data Exchange (ETDEWEB)

Chung, T.-H.; Chang, J.-Y. [Department of Chemical Engineering, National Chung Cheng University, Chiayi 621, Taiwan (China); Lee, W.-C. [Department of Chemical Engineering, National Chung Cheng University, Chiayi 621, Taiwan (China)], E-mail: chmwcl@ccu.edu.tw

2009-05-15

Surface-functionalized magnetic poly(styrene-glycidyl methacrylate) (PS-GMA) microspheres were prepared and coupled with Sca-1 antibody for cell selection from murine bone marrow mononuclear cells (MNCs). Biotinylated Sca-1 antibody could be directly coupled to avidin-bound magnetic microspheres. Alternatively, oxidized goat anti-mouse antibody was covalently bound onto the amino group-containing magnetic microspheres in a site-directed manner, and the resultant conjugate was coupled with non-modified Sca-1 antibody. Using the indirect antibody-bound magnetic microspheres, the purity of isolated Sca-1{sup +} cells increased with bead-to-cell ratio. Using a bead-to-cell ratio of 10 beads/cell, a purity of 85% Sca-1{sup +} cells corresponding to a 17-fold enrichment was achieved.

N-halamine biocidal coatings via a layer-by-layer assembly technique.

Science.gov (United States)

Cerkez, Idris; Kocer, Hasan B; Worley, S D; Broughton, R M; Huang, T S

2011-04-05

Two N-halamine copolymer precursors, poly(2,2,6,6-tetramethyl-4-piperidyl methacrylate-co-acrylic acid potassium salt) and poly(2,2,6,6-tetramethyl-4-piperidyl methacrylate-co-trimethyl-2-methacryloxyethylammonium chloride) have been synthesized and successfully coated onto cotton fabric via a layer-by-layer (LbL) assembly technique. A multilayer thin film was deposited onto the fiber surfaces by alternative exposure to polyelectrolyte solutions. The coating was rendered biocidal by a dilute household bleach treatment. The biocidal efficacies of tested swatches composed of treated fibers were evaluated against Staphylococcus aureus and Escherichia coli. It was determined that chlorinated samples inactivated both S. aureus and E. coli O157:H7 within 15 min of contact time, whereas the unchlorinated control samples did not exhibit significant biocidal activities. Stabilities of the coatings toward washing and ultraviolet light exposure have also been studied. It was found that the stability toward washing was superior, whereas the UVA light stability was moderate compared to previously studied N-halamine moieties. The layer-by-layer assembly technique can be used to attach N-halamine precursor polymers onto cellulose surfaces without using covalently bonding tethering groups which limit the structure designs. In addition, ionic precursors are very soluble in water, thus promising for biocidal coatings without the use of organic solvents.

Replacement of Poly(vinyl pyrrolidone) by Thiols: A Systematic Study of Ag Nanocube Functionalization by Surface-Enhanced Raman Scattering

OpenAIRE

Moran, Christine H.; Rycenga, Matthew; Zhang, Qiang; Xia, Younan

2011-01-01

In this work, we used surface-enhanced Raman scattering (SERS) to monitor the replacement of poly(vinyl pyrrolidone) (PVP) on Ag nanocubes by cysteamine, thiol-terminated PEG, and benzenedithiol. PVP is widely used as a colloidal stabilizer and capping agent to control the shape of Ag (as well as many other noble metals) nanocrystals during synthesis, and to stabilize the final colloidal suspension. However, the surface chemistry of Ag nanocrystals often needs to be tailored for specific appl...

Poly(glycidyl methacrylate) beads embedded cryogels for pseudo-specific affinity depletion of albumin and immunoglobulin G

Energy Technology Data Exchange (ETDEWEB)

Bereli, Nilay; Sener, Guelsu; Altintas, Evrim Banu; Yavuz, Handan [Department of Chemistry, Biochemistry Division, Hacettepe University, Ankara (Turkey); Denizli, Adil, E-mail: denizli@hacettepe.edu.tr [Department of Chemistry, Biochemistry Division, Hacettepe University, Ankara (Turkey)

2010-01-30

Depletion of high abundant proteins like albumin and immunoglobulin G (IgG) can be beneficial in the analysis of serum proteins. For this purpose, Cibacron Blue F3GA and iminodiacetic acid (IDA)-Cu{sup 2+} containing poly(glycidyl methacrylate) (PGMA) beads (1.6 {mu}m in diameter) were embedded into the poly(hydroxyethyl methacrylate) (PHEMA) cryogel. The PGMA beads were prepared by dispersion polymerization. The PGMA beads were modified with Cibacron Blue F3GA and iminodiacetic acid (IDA)-Cu{sup 2+} for simultaneous albumin and IgG depletion, respectively. The PHEMA cryogel was synthesized by free radical polymerization in the presence of the modified PGMA beads. The PHEMA and PHEMA/PGMA composite cryogels were characterized by swelling measurements and scanning electron microscopy (SEM). Protein depletion studies were carried out in a continuous experimental set-up in a stacked column. Albumin adsorption capacity of the PGMA-Cibacron Blue F3GA beads embedded PHEMA cryogel (PHEMA/PGMA-Cibacron Blue F3GA) was 342 mg/g and IgG adsorption capacity of the PGMA-IDA-Cu{sup 2+} beads embedded PHEMA cryogel (PHEMA/PGMA-IDA-Cu{sup 2+}) was 257 mg/g. The composite cryogels depleted albumin and IgG from human serum with 89.4% and 93.6% efficiency, respectively. High desorption values (over 90% for both modified cryogels) were achieved with 0.05 M phosphate buffer containing1.0 M NaCl.

Polysulfone hemodiafiltration membranes with enhanced anti-fouling and hemocompatibility modified by poly(vinyl pyrrolidone) via in situ cross-linked polymerization.

Science.gov (United States)

Zhu, Lijing; Song, Haiming; Wang, Jiarong; Xue, Lixin

2017-05-01

Poly(vinyl pyrrolidone) (PVP) and its copolymers have been widely employed for the modification of hemodiafiltration membranes due to their excellent hydrophilicity, antifouling and hemocompatibility. However, challenges still remain to simplify the modification procedure and to improve the utilization efficiency. In this paper, antifouling and hemocompatibility polysulfone (PSf) hemodiafiltration membranes were fabricated via in situ cross-linked polymerization of vinyl pyrrolidone (VP) and vinyltriethoxysilane (VTEOS) in PSf solutions and non-solvent induced phase separation (NIPS) technique. The prepared membranes were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), which suggested that VP and VTEOS have been cross-linked copolymerized in PSf membranes. The modified PSf membranes with high polymer content showed improved hydrophilicity, ultrafiltration and protein antifouling ability. In addition, the modified PSf membranes showed lower protein adsorption, inhibited platelet adhesion and deformation, prolonged the activated partial thromboplastin time (APTT), prothrombin time (PT), and decreased the content of fibrinogen (FIB) transferring to fibrin, indicating enhanced hemocompatibility. In a word, the present work provides a simple and effective one-step modification method to construct PSf membranes with improved hydrophilicity, antifouling and hemocompatibility. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of Temperature and pH on Immobilized Laccase Activity in Conjugated Methacrylate-Acrylate Microspheres

Directory of Open Access Journals (Sweden)

Siti Zulaikha Mazlan

2017-01-01

Full Text Available Immobilization of laccase on the functionalized methacrylate-acrylate copolymer microspheres was studied. Poly(glycidyl methacrylate-co-n-butyl acrylate microspheres consisting of epoxy groups were synthesized using facile emulsion photocuring technique. The epoxy groups in poly(GMA-co-nBA microspheres were then converted to amino groups. Laccase immobilization is based on covalent binding via amino groups on the enzyme surface and aldehyde group on the microspheres. The FTIR spectra showed peak at 1646 cm−1 assigned to the conformation of the polymerization that referred to GMA and nBA monomers, respectively. After modification of the polymer, intensity of FTIR peaks assigned to the epoxy ring at 844 cm−1 and 904 cm−1 was decreased. The results obtained from FTIR exhibit a good agreement with the epoxy content method. The activity of laccase-immobilized microspheres increased upon increasing the epoxy content. Furthermore, poly(GMA-co-nBA microspheres revealed uniform size below 2 µm that contributes to large surface area of the microspheres to be used as a matrix, thus increasing the enzyme capacity and enzymatic reaction. Immobilized enzyme also shifted to higher pH and temperature compared to free enzyme.

Amine functionalization of cellulose surface grafted with glycidyl methacrylate by γ-initiated RAFT polymerization

International Nuclear Information System (INIS)

Barsbay, Murat; Güven, Olgun; Kodama, Yasko

2016-01-01

This study presents the functionalization of poly(glycidyl methacrylate) (PGMA) grafted cellulose filter paper by a model compound, ethylenediamine (EDA), through the epoxy groups of PGMA. Cellulose based copolymers were prepared via the radiation-induced and RAFT-mediated graft polymerization. The samples were characterized by ATR–FTIR spectroscopy, X-ray photoelectron spectroscopy (XPS), elemental analysis, contact angle measurements and scanning electron microscopy (SEM). An efficient modification density of around 1 mmol EDA/mg copolymer was attained within ca. 8 h, indicating that chemical composition of well-defined copolymers may further be tuned by appropriately selecting the reactive agents for use in many emerging fields. - Highlights: • Ethylenediamine (EDA) was immobilized to cellulose-g-PGMA copolymers. • FTIR, XPS, SEM, EA and CA measurements were used for characterization. • The useful qualities of the RAFT were combined with the versatility of PGMA.

Investigation of anti-corrosive properties of poly(aniline-co-2-pyridylamine-co-2,3-xylidine) and its nanocomposite poly(aniline-co-2-pyridylamine-co-2,3-xylidine)/ZnO on mild steel in 0.1 M HCl

Science.gov (United States)

Alam, Ruman; Mobin, Mohammad; Aslam, Jeenat

2016-04-01

A soluble terpolymer of aniline (AN), 2-pyridylamine (PA) and 2,3-xylidine (XY), poly(AN-co-PA-co-XY) and its nanocomposite with ZnO nanoparticles namely, poly(AN-co-PA-co-XY)/ZnO were synthesized by chemical oxidative polymerization employing ammonium persulfate as an oxidant. Nanocomposites of homopolymers, polyaniline/ZnO, poly(XY)/ZnO and poly(PA)/ZnO were also synthesized by following similar synthesis route. FTIR, XRD and SEM techniques were used to characterize the synthesized compounds. The synthesized compounds were chemically deposited on mild steel specimens by solvent evaporation method using N-methyl-2-pyrrolidone (NMP) as solvent and 10% epoxy resin (by weight) as binder. Anticorrosive properties of homopolymer nanocomposites, terpolymer and its nanocomposite coatings were studied in 0.1 M HCl by subjecting them to various corrosion tests which includes: free corrosion potential measurement (OCP), weight loss measurements, potentiodynamic polarization, and AC impedance technique. The surface morphology of the corroded and uncorroded coated steel specimens was evaluated using SEM. The corrosion protection performance of terpolymer nanocomposite coating was compared to the terpolymer and individual homopolymers nanocomposites coatings after 30 days immersion in corrosive medium.

Modification of flax fibres by radiation induced emulsion graft copolymerization of glycidyl methacrylate

Science.gov (United States)

Moawia, Rihab Musaad; Nasef, Mohamed Mahmoud; Mohamed, Nor Hasimah; Ripin, Adnan

2016-05-01

Flax fibres were modified by radiation induced graft copolymerization of glycidyl methacrylate (GMA) by pre-irradiation method in an emulsion medium. The effect of reaction parameters on the degree of grafting (DOG) such as concentration of bleaching agent, absorbed dose, monomer concentration, temperature and reaction time were investigated. The DOG was found to be dependent on the investigated parameters. The incorporation of poly(GMA) grafts in the bleached flax fibres was confirmed by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The structural and mechanical changes were evaluated by X-ray diffraction (XRD) and mechanical tester, respectively. The results revealed that reacting bleached flax fibres irradiated with 20 kGy with 5% GMA emulsion containing 0.5% polyoxyethylene-sorbitan monolaurate (Tween 20) surfactant at 40 °C for 1 h led to a maximum DOG of 148%. The grafted fibres showed sufficient mechanical strength and hydrophobicity which make them promising precursors for development of adsorbents after appropriate chemical treatments.

Improvement of pesticide adsorption capacity of cellulose fibre by high-energy irradiation-initiated grafting of glycidyl methacrylate

International Nuclear Information System (INIS)

Takacs, E.; Wojnarovits, L.; Borsa, J.

2011-01-01

Complete text of publication follows. Sustainable development needs renewable raw materials applied wherever possible. Cellulose is the most abundant biopolymer on earth; various modifications of its properties for special uses are important issues of the research. Some contaminations in wastewaters, e.g. pesticides, are hydrophobic materials; their adsorption on hydrophilic cellulose substrates is very limited. Cotton cellulose was grafted by glycidyl methacrylate in simultaneous grafting using gamma irradiation initiation. Water uptake of cellulose significantly decreased while adsorption of phenol and a pesticide molecule (2,4-dichlorophenoxyacetic acid: 2,4-D) increased upon grafting. As the figure shows on untreated sample even negative 2,4-D adsorption occurred, due to the selective adsorption of water from the solution; the adsorption did not approach its saturation value even in a 30 hours time period investigated. Saturation of phenol adsorption was achieved after 5-6 hours; adsorption equilibrium data of phenol fitted the Langmuir isotherm.

Phase behavior for the poly(alkyl methacrylate)+supercritical CO{sub 2}+DME mixture at high pressures

Energy Technology Data Exchange (ETDEWEB)

Choi, Yong-Seok; Chio, Sang-Won; Byun, Hun-Soo [Chonnam National University, Yeosu (Korea, Republic of)

2016-01-15

The phase behavior curves of binary and ternary system were measured for poly(alkyl methacrylate) in supercritical CO{sub 2}, as well as for the poly(alkyl methacrylate)+dimethyl ether (DME) (or 1-butene) in CO{sub 2}. The solubility curves are reported for the poly(alkyl methacrylate)+DME in supercritical CO{sub 2} at temperature from (300 to 465) K and a pressure from (3.66 to 248) MPa. Also, The high-pressure static-type apparatus of cloud-point curve was tested by comparing the measured phase behavior data of the poly(methyl methacrylate) [PMMA]+CO{sub 2}+20.0 and 30.4 wt% methyl methacrylate (MMA) system with literature data of 10.4, 28.8 and 48.4 wt% MMA concentration. The phase behavior data for the poly(alkyl methacrylate)+CO{sub 2}+DME mixture were measured in changes of the pressure-temperature (p, T) slope and with DME concentrations. Also, the cloud-point pressure for the poly(alkyl methacrylate)+1- butene solution containing supercritical CO{sub 2} shows from upper critical solution temperature (UCST) region to lower critical solution temperature (LCST) region at concentration range from (0.0 to 95) wt% 1-butene at below 455 K and at below 245MPa.

Preparation of Thermoplastic Poly (vinyl Alcohol), Ethylene Vinyl Acetate and Vinyl Acetate Versatic Ester Blends for Exterior Masonry Coating

International Nuclear Information System (INIS)

EL-Nahas, H.H.; Gad, Y.H.; Magida, M.M.

2013-01-01

Blend systems including ethylene vinyl acetate (EVA), poly (vinyl alcohol) (PVA) and vinyl acetate versatic copolymer latex (VAcVe) were prepared and used as exterior coatings. Mechanical and thermal properties of the blends were investigated using a testo meter, shore hardness tester, thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). The water resistance of the samples was measured. Effect of ionizing irradiation on gel content, tensile strength and surface hardness were also followed. The blend offers binder base for exterior masonry coating systems having superior water resistant and mechanical properties

Optimization of process parameter for graft copolymerization of glycidyl methacrylate onto delignified banana fibers

International Nuclear Information System (INIS)

Selambakkannu, S.; Nor Azillah Fatimah Othman; Siti Fatahiyah Mohamad

2016-01-01

This paper focused on pre-treated banana fibers as a trunk polymer for optimization of radiation-induced graft copolymerization process parameters. Pre-treated banana fiber was grafted with glycidyl methacrylate (GMA) via electron beam irradiation. Optimization of grafting parameters in term of grafting yield was analyzed at numerous radiation dose, monomer concentration and reaction time. Grafting yield had been calculated gravimetrically against all the process parameters. The grafting yield at 40 kGy had increases from 14 % to 22.5 % at 1 h and 24 h of reaction time respectively. Grafting yield at 1 % of GMA was about 58 % and it increases to 187 % at 3 % GMA. The grafting of GMA onto pre-treated banana fibers confirmed with the characterization using FTIR, SEM and TGA. Grafting of GMA onto pre-treated fibers was successfully carried out and it was confirmed by the results obtained via the characterization. (author)

Polyaniline Coated Core-Shell Typed Stimuli-Responsive Microspheres and Their Electrorheology

Directory of Open Access Journals (Sweden)

Yu Zhen Dong

2018-03-01

Full Text Available Functional core-shell-structured particles have attracted considerable attention recently. This paper reviews the synthetic methods and morphologies of various electro-stimuli responsive polyaniline (PANI-coated core-shell-type microspheres, including PANI-coated Fe3O4, SiO2, Fe2O3, TiO2, poly(methyl methacrylate, poly(glycidyl methacrylate, and polystyrene along with their electrorheological (ER characteristics when prepared by dispersing these particles in an insulating medium. In addition to the various rheological characteristics and their analysis, such as shear stress and yield stress of their ER fluids, this paper summarizes some of the mechanisms proposed for ER fluids to further understand the responses of ER fluids to an externally applied electric field.

Preparation of Ethylene Vinyl Acetate/Zeolite 4A Mixed Matrix Membrane for CO2/N2 Separation

Directory of Open Access Journals (Sweden)

Iman Khalilinejad

2016-07-01

Full Text Available A great contribution in research activities on carbon dioxide (CO2 separation, as the most important challenge in greenhouse gases control, has been made to develop new polymeric membranes. In this case, mixed matrix membranes (MMMs, comprised of rigid particles dispersed in a continuous polymeric matrix, was proposed as an effective method to improve the separation properties of polymeric membranes. In this research, ethylene vinyl acetate (EVA copolymer and zeolite 4A powders were applied to prepare MMMs using solution casting/solvent evaporation method and CO2/N2 separation performance of the membranes was examined under different feed pressures (3-8 bar and operating temperatures (25-50°C. Morphological and structural characterizations of the membranes were evaluated using scanning electron microscopy (SEM, Fourier transform infrared (FTIR spectroscopy, differential scanning calorimetry (DSC, thermogravimetric analysis (TGA, density and solvent-induced swelling measurements. The gas permeability measurements through the constant-volume method showed the permeability of two gases increased in the presence of zeolite 4A nanoparticles in the polymer matrix. Calculation of diffusivity coefficients of gases revealed that improvement in the diffusivity of all gases into membrane matrix was the main reason for permeability enhancement. In addition, the increase in the CO2/N2 ideal selectivity with the presence of zeolite 4A nanoparticles in the polymer matrix was attributed to the increment in CO2/N2 diffusion selectivity. Under optimum condition, with the addition of 10 wt% zeolite 4A nanoparticles into the membrane matrix, the CO2 permeability increased from 20.81 to 35.24 Barrer and its related selectivity increased 20% compared to that of neat EVA membrane. Furthermore, the membrane performances increased upon feed pressure rise, while the selectivity decreased with the increase in temperature.

Kinetic investigations of emulsion- and solvent-mediated radiation induced graft copolymerization of glycidyl methacrylate onto nylon-6 fibres

International Nuclear Information System (INIS)

Teo Ming Ting; Paveswari Sithambaranathan

2017-01-01

Kinetic behaviour of graft copolymerisation of glycidyl methacrylate onto nylon-6 fibres in solvent- and emulsion- media was investigated. The order for the dependence of the initial rate of grafting on the monomer concentration for solvent and emulsion grafting systems were found to be 1.65 and 1.57, respectively. The order of dependence of the initial rate of grafting on the absorbed dose was found to be 1.55 for solvent and 0.62 emulsion grafting systems. The results showed that grafting in both systems is controlled by diffusion mechanism and the degree of grafting can be effectively tuned by variation of the grafting parameters. (author)

Polysulfone hemodiafiltration membranes with enhanced anti-fouling and hemocompatibility modified by poly(vinyl pyrrolidone) via in situ cross-linked polymerization

Energy Technology Data Exchange (ETDEWEB)

Zhu, Lijing, E-mail: zhulijing@nimte.ac.cn; Song, Haiming; Wang, Jiarong; Xue, Lixin, E-mail: xuelx@nimte.ac.cn

2017-05-01

Poly(vinyl pyrrolidone) (PVP) and its copolymers have been widely employed for the modification of hemodiafiltration membranes due to their excellent hydrophilicity, antifouling and hemocompatibility. However, challenges still remain to simplify the modification procedure and to improve the utilization efficiency. In this paper, antifouling and hemocompatibility polysulfone (PSf) hemodiafiltration membranes were fabricated via in situ cross-linked polymerization of vinyl pyrrolidone (VP) and vinyltriethoxysilane (VTEOS) in PSf solutions and non-solvent induced phase separation (NIPS) technique. The prepared membranes were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), which suggested that VP and VTEOS have been cross-linked copolymerized in PSf membranes. The modified PSf membranes with high polymer content showed improved hydrophilicity, ultrafiltration and protein antifouling ability. In addition, the modified PSf membranes showed lower protein adsorption, inhibited platelet adhesion and deformation, prolonged the activated partial thromboplastin time (APTT), prothrombin time (PT), and decreased the content of fibrinogen (FIB) transferring to fibrin, indicating enhanced hemocompatibility. In a word, the present work provides a simple and effective one-step modification method to construct PSf membranes with improved hydrophilicity, antifouling and hemocompatibility. - Highlights: • PSf membranes were modified by in situ cross-linked polymerization. • The modified PSf membranes showed enhanced hydrophilicity. • The anti-fouling and hemocompatibility of PSf membranes were improved.

Polysulfone hemodiafiltration membranes with enhanced anti-fouling and hemocompatibility modified by poly(vinyl pyrrolidone) via in situ cross-linked polymerization

International Nuclear Information System (INIS)

Zhu, Lijing; Song, Haiming; Wang, Jiarong; Xue, Lixin

2017-01-01

Poly(vinyl pyrrolidone) (PVP) and its copolymers have been widely employed for the modification of hemodiafiltration membranes due to their excellent hydrophilicity, antifouling and hemocompatibility. However, challenges still remain to simplify the modification procedure and to improve the utilization efficiency. In this paper, antifouling and hemocompatibility polysulfone (PSf) hemodiafiltration membranes were fabricated via in situ cross-linked polymerization of vinyl pyrrolidone (VP) and vinyltriethoxysilane (VTEOS) in PSf solutions and non-solvent induced phase separation (NIPS) technique. The prepared membranes were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), which suggested that VP and VTEOS have been cross-linked copolymerized in PSf membranes. The modified PSf membranes with high polymer content showed improved hydrophilicity, ultrafiltration and protein antifouling ability. In addition, the modified PSf membranes showed lower protein adsorption, inhibited platelet adhesion and deformation, prolonged the activated partial thromboplastin time (APTT), prothrombin time (PT), and decreased the content of fibrinogen (FIB) transferring to fibrin, indicating enhanced hemocompatibility. In a word, the present work provides a simple and effective one-step modification method to construct PSf membranes with improved hydrophilicity, antifouling and hemocompatibility. - Highlights: • PSf membranes were modified by in situ cross-linked polymerization. • The modified PSf membranes showed enhanced hydrophilicity. • The anti-fouling and hemocompatibility of PSf membranes were improved.

Porous polymer monoliths functionalized through copolymerization of a C60 fullerene-containing methacrylate monomer for highly efficient separations of small molecules

KAUST Repository

Chambers, Stuart D.

2011-12-15

Monolithic poly(glycidyl methacrylate-co-ethylene dimethacrylate) and poly(butyl methacrylate-co-ethylene dimethacrylate) capillary columns, which incorporate the new monomer [6,6]-phenyl-C 61-butyric acid 2-hydroxyethyl methacrylate ester, have been prepared and their chromatographic performance have been tested for the separation of small molecules in the reversed phase. While addition of the C60-fullerene monomer to the glycidyl methacrylate-based monolith enhanced column efficiency 18-fold, to 85 000 plates/m at a linear velocity of 0.46 mm/s and a retention factor of 2.6, when compared to the parent monolith, the use of butyl methacrylate together with the carbon nanostructured monomer afforded monolithic columns with an efficiency for benzene exceeding 110 000 plates/m at a linear velocity of 0.32 mm/s and a retention factor of 4.2. This high efficiency is unprecedented for separations using porous polymer monoliths operating in an isocratic mode. Optimization of the chromatographic parameters affords near baseline separation of 6 alkylbenzenes in 3 min with an efficiency of 64 000 plates/m. The presence of 1 wt % or more of water in the polymerization mixture has a large effect on both the formation and reproducibility of the monoliths. Other factors such as nitrogen exposure, polymerization conditions, capillary filling method, and sonication parameters were all found to be important in producing highly efficient and reproducible monoliths. © 2011 American Chemical Society.

Organic inorganic hybrid coating (poly(methyl methacrylate)/monodisperse silica)

Science.gov (United States)

Rubio, E.; Almaral, J.; Ramírez-Bon, R.; Castaño, V.; Rodríguez, V.

2005-04-01

Polymethylmethacrylate-silica hybrid coatings were prepared from methyl methacrylate and monodisperse colloidal silica prepared by the Stöber method. The surfaces of the spheres were successfully modified by chemical reaction with 3-(trimethoxysilyl) propyl methacrylate (TMSPM) to compatibilise the organic and inorganic components of the precursor solution mixture. The coatings were deposited by dip-coating on glass substrates. They result with good properties of homogeneity, optical transparence, hardness and adhesion.

Photochemical synthesis of copper nanoparticles incorporated in poly(vinyl pyrrolidone)

International Nuclear Information System (INIS)

Giuffrida, Salvatore; Costanzo, Lucia L.; Ventimiglia, Giorgio; Bongiorno, Corrado

2008-01-01

The effect of the presence of poly(vinyl pyrrolidone) (PVP) on the copper nanoparticle formation, obtained by UV irradiation of ethanol solution of Cu(acac) 2 (acac = 2,4-pentanedionato), was investigated. At 254 nm, in conditions of light completely absorbed by complex, the PVP exhibited protective and stabilizing effects, as shown by the formation of a colloidal copper solution and by a block of the heterogeneous process, which leads to thin film formation on the quartz walls. The colloidal solution was tested for several months by plasmon position and it was found that it remained unaltered in inert atmosphere, but returned to the starting complex on contact with air. The PVP ability to control the particle size was investigated by carrying out photoreduction sensitized by Hacac at 254 and 300 nm, in the presence of PVP concentration varying from 0 to 0.2 M. In this range it was possible to obtain copper nanoparticles of dimensions decreasing from 30 to 4 nm. Besides this, the PVP (0.005-0.05 M) role as sensitizer was investigated by irradiating solutions of Cu(acac) 2 at 300 nm which is an inactive wavelength for copper reduction by direct light absorption. It was found that the PVP was an efficient sensitizer of the copper photoreduction. The nanoparticles were characterized by plasmon band, Trasmission Electron Microscope (TEM) as well as Dynamic Light Scattering (DSL) analysis. The overall results evidence the advantages of the PVP use in the nanoparticle copper formation through the photochemical technique such as the exclusive formation of colloidal copper, their size control, stable colloidal solution and complete return to the starting complex.

Evaluation of glycidyl methacrylate-based monolith functionalized with weak anion exchange moiety inside 0.5 mm i.d. column for liquid chromatographic separation of DNA

Directory of Open Access Journals (Sweden)

Aprilia Nur Tasfiyati

2016-03-01

Full Text Available In this study, the organic polymer monolith was developed as a weak anion exchanger column in high performance liquid chromatography for DNA separation. Methacrylate-based monolithic column was prepared in microbore silicosteel column (100 × 0.5 mm i.d. by in-situ polymerization reaction using glycidyl methacrylate as monomer; ethylene dimethacrylate as crosslinker; 1-propanol, 1,4-butanediol, and water as porogenic solvents, with the presence of initiator α,α′-azobisisobutyronitrile (AIBN. The monolith matrix was modified with diethylamine to create weak anion exchanger via ring opening reaction of epoxy groups. The morphology of the monolithic column was studied by SEM. The properties of the monolithic column, such as permeability, mechanical stability, binding capacity and pore size distribution, were characterized in detail. From the results of the characterization, monoliths poly-(GMA-co-EDMA with total monomer percentage (%T 40 and crosslinker percentage (%C 25 was found to be the ideal composition of monomer and crosslinker. It has good mechanical stability and high permeability, adequate molecular recognition sites (represented with binding capacity value of 36 mg ml−1, and has relatively equal proportion of flow-through pore and mesopores (37.2% and 41.1% respectively. Poly-(GMA-co-EDMA with %T 40 and %C 25 can successfully separate oligo(dT12–18 and 50 bp DNA ladder with good resolution.

Synthesis and characterization of functional acrylic copolymers via RAFT mini-emulsion polymerization

Science.gov (United States)

Yılmaz, Onur; Özkan, ćiǧdem Kılıçarislan; Yılmaz, Catalina N.; Yorgancıoǧlu, Ali; Özgünay, Hasan; Karavana, Hüseyin Ata

2017-12-01

Copolymers bearing reactive functional groups with controlled molecular weights are of importance since they can be used in many fields such as composites, coatings, membranes, catalysis, biology, optoelectronics, pharmaceuticals, etc. In the present study low molecular weight copolymers based on butyl acrylate (BA) and methyl methacrylate (MMA) in combination with reactive functional monomers of vinyl trietoxysilane (VTES), 3-trimetoxysilylpropyl methacrylate (TMSPMA) and glycidyl methacrylate (GMA) were synthesized via RAFT mini-emulsion technique using 2-cyano 2-propyldodecyldithiocarbonate as CTA agent. The results showed that the average molecular weights of copolymers were close to the theoretical values. On the other hand, PDI values were found to be higher than conventional RAFT polymers. The particle sizes of the latexes were small with very homogenous distributions and good stability. FTIR, H-NMR and TGA results verified the success of copolymer syntheses.

Covalently coating dextran on macroporous polyglycidyl methacrylate microsphere enabled rapid protein chromatographic separation

Energy Technology Data Exchange (ETDEWEB)

Zhang, Rongyue; Li, Qiang; Li, Juan; Zhou, Weiqing; Ye, Peili; Gao, Yang; Ma, Guanghui, E-mail: ghma@home.ipe.ac.cn; Su, Zhiguo

2012-12-01

Protein denaturation and nonspecific adsorption on polymer media as a chromatographic support have been a problem which needs to be overcome. Macroporous poly(glycidyl methacrylate-divinylbezene) (PGMA-DVB) microspheres prepared in this study were firstly covalently coated with dextran through a three-step method. The dextran was firstly adsorbed onto the microspheres and then covalently bound to the PGMA-DVB microsphere through ether bonds which were formed by hydroxyl group reacting with epoxy group at the presence of 4-(Dimethylamino) pyridine. Finally, the coating dextran layer was crosslinked by ethylene glycol diglycidyl ether to form the continuous network coating. The coated microspheres were characterized by Fourier transform infrared spectra, scanning electron microscope, mercury porosimetry measurements, laser scanning confocal microscope, and protein adsorption experiments. Results showed that PGMA-DVB microspheres coated with dextran successfully maintained the macroporous structure and high permeability. The backpressure was only 1.69 MPa at a high flow rate of 2891 cm/h. Consequently, the hydrophilicity and biocompatibility of modified microspheres were greatly improved, and the contact angle decreased from 184 Degree-Sign to 13 Degree-Sign , and nonspecific adsorption of proteins was decreased to little or none. The clad dextran coating with large amounts of hydroxyl group was easily derived to be various functional groups. The derived media have great potential applications in rapid protein chromatography. - Highlights: Black-Right-Pointing-Pointer Macroporous PGMA-DVB microspheres were covalently coated with dextran. Black-Right-Pointing-Pointer The hydrophilicity of the coated microspheres was significantly improved. Black-Right-Pointing-Pointer The irreversible adsorption of proteins was reduced to zero. Black-Right-Pointing-Pointer The coated microspheres can maintain the macropore structure. Black-Right-Pointing-Pointer The coated microspheres

Rapid Quantification of N-Methyl-2-pyrrolidone in Polymer Matrices by Thermal Desorption-GC/MS.

Science.gov (United States)

Kim, Young-Min; Kim, Jae Woo; Moon, Hye Mi; Lee, Min-Jin; Hosaka, Akihiko; Watanabe, Atsushi; Teramae, Norio; Park, Young-Kwon; Myung, Seung-Woon

2017-01-01

Analysis of a residual solvent in polymeric materials has become an important issue due to the increased regulations and standards for its use. N-Methyl-2-pyrrolidone (NMP) is a solvent widely used in many industries and restricted as one of the chemicals under EU REACH regulations due to its potential harmful effects. In this study, thermal desorption-gas chromatography/mass spectrometry (TD-GC/MS) is applied for the quantitative analysis of NMP with the use of a polymer-coated sample cup. By using the polymer-coated sample cup, the vaporization of NMP was prevented during waiting time before TD-GC/MS analysis. The calibration curve for the TD method showed good linearity (correlation coefficient, r 2 = 0.9998) and precision values (below 5.3% RSD). NMP recovery rates in different polymer matrices (PS, PMMA and PVC) were in the range of 98.8 to 106.6% with RSD values below 5.0%. The quantification result (600 mg NMP/kg PVC) for the blind NMP carrying sample in a PVC matrix by TD-GC/MS was higher than that (532 mg NMP/kg PVC) by solvent extraction-GC/MS method.

Synthesis and characterization of functionalized methacrylates for coatings and biomedical applications

Science.gov (United States)

Shemper, Bianca Sadicoff

The research presented in this dissertation involves the design of polymers for biomaterials and for coatings applications. The development of non-wettable, hard UV-curing, or reactive coatings is discussed. The biomaterials section involves the syntheses of linear and star-like polymers of the functionalized monomer poly(propylene glycol) monomethacrylate (PPGM) via atom transfer radical polymerization (ATRP) (Chapter II). Its copolymerization with a perfluoroalkyl ethyl methacrylate monomer (1H,1H,2H,2H-heptadecafluorodecyl methacrylate) and the syntheses of linear and star-like amphiphilic copolymers containing the fluorinated monomer and poly(ethyleneglycol) methyl ether methacrylate (MPEGMA) are discussed in Chapter III. The four-arm amphiphilic block copolymer obtained showed unique associative properties leading to micellization in selective solvents. Chapter IV includes research involving the design of films with low surface energy by incorporating fluorine into the polymer. The synthesis, characterization and polymerization of a perfluoroalkylether-substituted methacrylic acid (C8F7) are discussed, and the properties of coatings obtained after its photopolymerization on different substrates are evaluated to confirm formation of low-surface energy polymeric coatings. Subsequently, hard coatings based on methyl (alpha-hydroxymethyl)acrylate (MHMA) were prepared via photopolymerization using UV-light. Firstly, mechanistic investigations into the photopolymerization behavior of (alpha-hydroxymethyl)acrylates (RHMA's) are reported (Chapter V). RHMA derivatives were photopolymerized with various multifunctional acrylates and methacrylates and the effect of crosslinker type and degree of functionality on photopolymerization rates and conversions was investigated. Then, in Chapter VI the synthesis of a series of new crosslinkers is described and their photopolymerization kinetics was investigated in bulk. The effect of these novel crosslinkers on the

Role of N-methyl-2-pyrrolidone for preparation of Fe{sub 3}O{sub 4}@SiO{sub 2} controlled the shell thickness

Energy Technology Data Exchange (ETDEWEB)

Wee, Sung-Bok [Hanyang University, Division of Materials Science and Engineering (Korea, Republic of); Oh, Hyeon-Cheol [Korea Nano Plus, Inc. (Korea, Republic of); Kim, Tae-Gyun; An, Gye-Seok; Choi, Sung-Churl, E-mail: choi0505@hanyang.ac.kr [Hanyang University, Division of Materials Science and Engineering (Korea, Republic of)

2017-04-15

We developed a simple and novel approach for the synthesis of Fe{sub 3}O{sub 4}@SiO{sub 2} nanoparticles with controlled shell thickness, and studied the mechanism. The introduction of N-methyl-2-pyrrolidone (NMP) led to trapping of monomer nuclei in single shell and controlled the shell thickness. Fe{sub 3}O{sub 4}@SiO{sub 2} controlled the shell thickness, showing a high magnetization value (64.47 emu/g). Our results reveal the role and change in the chemical structure of NMP during the core-shell synthesis process. NMP decomposed to 4-aminobutanoic acid in alkaline condition and decreased the hydrolysis rate of the silica coating process.

Water-stable diblock polystyrene-block-poly(2-vinyl pyridine) and diblock polystyrene-block-poly(methyl methacrylate) cylindrical patterned surfaces inhibit settlement of zoospores of the green alga Ulva.

Science.gov (United States)

Grozea, Claudia M; Gunari, Nikhil; Finlay, John A; Grozea, Daniel; Callow, Maureen E; Callow, James A; Lu, Zheng-Hong; Walker, Gilbert C

2009-04-13

Nanopatterned surfaces with hydrophobic and hydrophilic domains were produced using the diblock copolymer polystyrene-block-poly(2-vinyl pyridine) (PS-b-P2VP) and polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA). The PS-b-P2VP diblock copolymer, mixed with the cross-linker benzophenone and spin-coated onto silicon wafers, showed self-assembled cylindrical structures, which were retained after UV treatment for cross-linking. The thin films displayed cylindrical domains after immersion in water. This study shows that pattern retention in water is possible for a long period of time, at least for two weeks in pure water and three weeks in artificial seawater. The PS-b-PMMA diblock showed self-assembled cylindrical structures. PS-b-P2VP and PS-b-PMMA cylindrical patterned surfaces showed reduced settlement of zoospores of the green alga Ulva compared to unpatterned surfaces. The copolymers were investigated using atomic force microscopy and X-ray photoelectron spectroscopy.

Multifunctional methacrylate-based coatings for glass and metal surfaces

Science.gov (United States)

Pospiech, Doris; Jehnichen, Dieter; Starke, Sandra; Müller, Felix; Bünker, Tobias; Wollenberg, Anne; Häußler, Liane; Simon, Frank; Grundke, Karina; Oertel, Ulrich; Opitz, Michael; Kruspe, Rainer

2017-03-01

In order to prevent freshwater biofouling glass and metal surfaces were coated with novel transparent methacrylate-based copolymers. The multifunctionality of the copolymers, such as adhesion to the substrate, surface polarity, mechanical long-term stability in water, and ability to form metal complexes was inserted by the choice of suitable comonomers. The monomer 2-acetoacetoxy ethyl methacrylate (AAMA) was used as complexing unit to produce copper(II) complexes in the coating's upper surface layer. The semifluorinated monomer 1H,1H,2H,2H-perfluorodecyl methacrylate was employed to adjust the surface polarity and wettability. Comprehensive surface characterization techniques, such as X-ray photoelectron spectroscopy (XPS) and contact angle measurements showed that surface compositions and properties can be easily adjusted by varying the concentrations of the comonomers. The formation of copper(II) complexes along the copolymer chains and their stability against washing out with plenty of water was proven by XPS. Copolymers containing semifluorinated comonomers significantly inhibited the growth of Achnanthidium species. Copolymers with copper-loaded AAMA-sequences were able to reduce both the growth of Achnanthidium spec. and Staphylococcus aureus.

Growth of MCF-7 breast cancer cells and efficacy of anti-angiogenic agents in a hydroxyethyl chitosan/glycidyl methacrylate hydrogel.

Science.gov (United States)

Wang, Hejing; Qian, Junmin; Zhang, Yaping; Xu, Weijun; Xiao, Juxiang; Suo, Aili

2017-01-01

Breast cancer negatively affects women's health worldwide. The tumour microenvironment plays a critical role in tumour initiation, proliferation, and metastasis. Cancer cells are traditionally grown in two-dimensional (2D) cultures as monolayers on a flat solid surface lacking cell-cell and cell-matrix interactions. These experimental conditions deviate from the clinical situation. Improved experimental systems that can mimic the in vivo situation are required to discover new therapies, particularly for anti-angiogenic agents that mainly target intercellular factors and play an essential role in treating some cancers. Chitosan can be modified to construct three-dimensional (3D) tumour models. Here, we report an in vitro 3D tumour model using a hydroxyethyl chitosan/glycidyl methacrylate (HECS-GMA) hydrogel produced by a series of chitosan modifications. Parameters relating to cell morphology, viability, proliferation, and migration were analysed using breast cancer MCF-7 cells. In a xenograft model, secretion of angiogenesis-related growth factors and the anti-angiogenic efficacy of Endostar and Bevacizumab in cells grown in HECS-GMA hydrogels were assessed by immunohistochemistry. Hydroxyethyl chitosan/glycidyl methacrylate hydrogels had a highly porous microstructure, mechanical properties, swelling ratio, and morphology consistent with a 3D tumour model. Compared with a 2D monolayer culture, breast cancer MCF-7 cells residing in the HECS-GMA hydrogels grew as tumour-like clusters in a 3D formation. In a xenograft model, MCF-7 cells cultured in the HECS-GMA hydrogels had increased secretion of angiogenesis-related growth factors. Recombinant human endostatin (Endostar), but not Bevacizumab (Avastin), was an effective anti-angiogenic agent in HECS-GMA hydrogels. The HECS-GMA hydrogel provided a 3D tumour model that mimicked the in vivo cancer microenvironment and supported the growth of MCF7 cells better than traditional tissue culture plates. The HECS

Thermally Oxidized C, N Co-Doped ANATASE-TiO2 Coatings on Stainless Steel for Tribological Properties

Science.gov (United States)

Wang, Hefeng; Shu, Xuefeng; Li, Xiuyan; Tang, Bin; Lin, Naiming

2013-07-01

Ti(C, N) coatings were prepared on stainless steel (SS) substrates by plasma surface alloying technique. Carbon-nitrogen co-doped titanium dioxide (C-N-TiO2) coatings were fabricated by oxidative of the Ti(C, N) coatings in air. The prepared C-N-TiO2 coatings were characterized by SEM, XPS and XRD. Results reveal that the SS substrates were entirely shielded by the C-N-TiO2 coatings. The C-N-TiO2 coatings are anatase in structure as characterized by X-ray diffraction. The tribological behavior of the coatings was tested with ball-on-disc sliding wear and compared with substrate. Such a C-N-TiO2 coatings showed good adhesion with the substrate and tribological properties of the SS in terms of much reduced friction coefficient and increased wear resistance.

Antibacterial performance of polypropylene nonwoven fabric wound dressing surfaces containing passive and active components

International Nuclear Information System (INIS)

Xin, Zhirong; Du, Shanshan; Zhao, Chunyu; Chen, Hao; Sun, Miao; Yan, Shunjie; Luan, Shifang; Yin, Jinghua

2016-01-01

Graphical abstract: - Highlights: • PNVP and PHMG components were covalently immobilized on PP_N_W_F surface. • PP_N_W_F-g-PNVP-PHMG possessed bacterial adhesion-resistant and bactericidal capabilities. • PP_N_W_F-g-PNVP-PHMG obviously suppressed platelet and red blood cell adhesion. - Abstract: A growing number of wound dressing-related nosocomial infections necessitate the development of novel antibacterial strategies. Herein, polypropylene non-woven fabric (PP_N_W_F) was facilely modified with passive and active antibacterial components, namely photografting polymerization both N-Vinyl-2-pyrrolidone (NVP) and glycidyl methacrylate (GMA) monomers, and the introduction of guanidine polymer through the reaction between active amino groups and epoxy groups. The modified samples were confirmed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), respectively. Water contact angle measurement, antibacterial test, platelet and red blood cell adhesion were used to evaluate the hydrophilicity, antibacterial properties and hemocompatibility of the samples. It was found that the antibacterial properties were obviously enhanced, meanwhile significantly suppressing platelet and red blood cell adhesion after the above modification. This PP_N_W_F samples that possess antifouling and antimicrobial properties, have great potential in wound dressing applications.

Multifunctional methacrylate-based coatings for glass and metal surfaces

Energy Technology Data Exchange (ETDEWEB)

Pospiech, Doris, E-mail: pospiech@ipfdd.de [Leibniz-Institut für Polymerforschung Dresden e. V., Dresden (Germany); Jehnichen, Dieter [Leibniz-Institut für Polymerforschung Dresden e. V., Dresden (Germany); Starke, Sandra; Müller, Felix [Leibniz-Institut für Polymerforschung Dresden e. V., Dresden (Germany); Technische Universität Dresden, Organic Chemistry of Polymers, Dresden (Germany); Bünker, Tobias [Leibniz-Institut für Polymerforschung Dresden e. V., Dresden (Germany); Wollenberg, Anne [Leibniz-Institut für Polymerforschung Dresden e. V., Dresden (Germany); Technische Universität Dresden, Organic Chemistry of Polymers, Dresden (Germany); Häußler, Liane; Simon, Frank; Grundke, Karina; Oertel, Ulrich [Leibniz-Institut für Polymerforschung Dresden e. V., Dresden (Germany); Opitz, Michael; Kruspe, Rainer [IDUS Biologisch Analytisches Umweltlabor GmbH, Ottendorf-Okrilla (Germany)

2017-03-31

Highlights: • New methacrylate-based copolymers synthesized by free radical polymerization. • Comonomer AAMA was able to complex Cu (II) ions in solvent annealing procedure. • Coatings had efficient anti-biofouling efficacy. - Abstract: In order to prevent freshwater biofouling glass and metal surfaces were coated with novel transparent methacrylate-based copolymers. The multifunctionality of the copolymers, such as adhesion to the substrate, surface polarity, mechanical long-term stability in water, and ability to form metal complexes was inserted by the choice of suitable comonomers. The monomer 2-acetoacetoxy ethyl methacrylate (AAMA) was used as complexing unit to produce copper(II) complexes in the coating’s upper surface layer. The semifluorinated monomer 1H,1H,2H,2H-perfluorodecyl methacrylate was employed to adjust the surface polarity and wettability. Comprehensive surface characterization techniques, such as X-ray photoelectron spectroscopy (XPS) and contact angle measurements showed that surface compositions and properties can be easily adjusted by varying the concentrations of the comonomers. The formation of copper(II) complexes along the copolymer chains and their stability against washing out with plenty of water was proven by XPS. Copolymers containing semifluorinated comonomers significantly inhibited the growth of Achnanthidium species. Copolymers with copper-loaded AAMA-sequences were able to reduce both the growth of Achnanthidium spec. and Staphylococcus aureus.

Multifunctional methacrylate-based coatings for glass and metal surfaces

International Nuclear Information System (INIS)

Pospiech, Doris; Jehnichen, Dieter; Starke, Sandra; Müller, Felix; Bünker, Tobias; Wollenberg, Anne; Häußler, Liane; Simon, Frank; Grundke, Karina; Oertel, Ulrich; Opitz, Michael; Kruspe, Rainer

2017-01-01

Highlights: • New methacrylate-based copolymers synthesized by free radical polymerization. • Comonomer AAMA was able to complex Cu (II) ions in solvent annealing procedure. • Coatings had efficient anti-biofouling efficacy. - Abstract: In order to prevent freshwater biofouling glass and metal surfaces were coated with novel transparent methacrylate-based copolymers. The multifunctionality of the copolymers, such as adhesion to the substrate, surface polarity, mechanical long-term stability in water, and ability to form metal complexes was inserted by the choice of suitable comonomers. The monomer 2-acetoacetoxy ethyl methacrylate (AAMA) was used as complexing unit to produce copper(II) complexes in the coating’s upper surface layer. The semifluorinated monomer 1H,1H,2H,2H-perfluorodecyl methacrylate was employed to adjust the surface polarity and wettability. Comprehensive surface characterization techniques, such as X-ray photoelectron spectroscopy (XPS) and contact angle measurements showed that surface compositions and properties can be easily adjusted by varying the concentrations of the comonomers. The formation of copper(II) complexes along the copolymer chains and their stability against washing out with plenty of water was proven by XPS. Copolymers containing semifluorinated comonomers significantly inhibited the growth of Achnanthidium species. Copolymers with copper-loaded AAMA-sequences were able to reduce both the growth of Achnanthidium spec. and Staphylococcus aureus.

Fluorescence Imaging in Genipin Crosslinked Chitosan–Poly(vinyl pyrrolidone Hydrogels

Directory of Open Access Journals (Sweden)

Simon Matcham

2016-10-01

Full Text Available Recent research has identified genipin as a promising natural crosslinking agent for biocompatible hydrogels as genipin is significantly less cytotoxic than current synthetic crosslinking agents, such as glutaraldehyde. Conveniently, fluorophores can be produced when genipin crosslinks. In this study, fluorescence intensity measurements of genipin crosslinked chitosan-poly(vinyl pyrrolidone hydrogels have been explored as a dynamic, in situ method for tracing sol-gel transition. These pH-responsive smart materials have a future in medical applications, in particular in tissue engineering and drug delivery, where methods to follow the process in situ and in real-time are crucial for future advancement. Samples were prepared using deionised water, pH 4, and pH 10 solutions, and studied at 24 and 37 °C over a 24 h period. Both temperature and pH have been found to affect sol-gel transition in the hydrogels studied. The transition from acidic (pH 4 to basic (pH 10 solution resulted in reduced fluorescence intensity suggesting that, under more basic conditions, genipin molecules self-polymerise, reducing the number of molecules available for reaction with the amino groups of chitosan. Three-dimensional representations of the fluorescence present in a hydrogel sample have also been produced from the data, enabling the visualisation of variation in fluorescence with time at the surface of the hydrogel.

Preparation of Rhodamine B Fluorescent Poly(methacrylic acid) Coated Gelatin Nanoparticles

OpenAIRE

Gan, Zhenhai; Ju, Jianhui; Zhang, Ting; Wu, Daocheng

2011-01-01

Poly(methacrylic acid) (PMAA)-coated gelatin nanoparticles encapsulated with fluorescent dye rhodamine B were prepared by the coacervation method with the aim to retard the release of rhodamine B from the gelatin matrix. With sodium sulfate as coacervation reagent for gelatin, a kind of biopolymer with excellent biocompatibility, the formed gelatin nanoparticles were cross-linked by formaldehyde followed by the polymerization of methacrylic acid coating. The fluorescent poly(methacrylic acid)...

Influence of chain microstructure on thermodegradative behavior of furfuryl methacrylate-N-vinylpyrrolidone random copolymers by thermogravimetry

Energy Technology Data Exchange (ETDEWEB)

Peniche, C.; Zaldivar, D. (Univ. de la Habana, Havana (Cuba). Centro de Biomateriales); Bulay, A. (Plastmassi, Moscow (Russian Federation)); Roman, J.S. (CSIC, Madrid (Spain). Inst. de Ciencia y Tecnologia de Polimeros)

1993-12-20

The thermal behavior of random copolymers of furfuryl methacrylate (F) and N-vinyl-pyrrolidone (P) was studied by means of dynamic thermogravimetric analysis (TGA) in the range 100--600 C. The dynamic experiments show that these copolymers exhibit two degradation steps in the intervals 260--320 C and 350--520 C, respectively. The normalized weight loss in the low temperature interval increases as the mole fraction of F in the copolymer m[sub F] increases, whereas an inverted trend in the high temperature interval is observed. The apparent activation energy E[sub a] of the first degradation step for copolymers prepared with different composition, was obtained according to the treatment suggested by Broido. A plot of the values of E[sub a] versus the F dead molar fraction in the copolymer chains m[sub FF] gave a straight line that indicates that there is a direct relationship between the thermogravimetric behavior of these systems and their corresponding microstructure, that is, the distribution of comonomeric units along the copolymers chains. The first decomposition step was also studied by isothermal TGA and a good linearity for the variation of the weight loss percentage [Delta]W versus m[sub F] at least during the first 30 min of treatment was obtained.

New insights on poly(vinyl acetate)-based coated floating tablets: characterisation of hydration and CO2 generation by benchtop MRI and its relation to drug release and floating strength.

Science.gov (United States)

Strübing, Sandra; Abboud, Tâmara; Contri, Renata Vidor; Metz, Hendrik; Mäder, Karsten

2008-06-01

The purpose of this study was to investigate the mechanism of floating and drug release behaviour of poly(vinyl acetate)-based floating tablets with membrane controlled drug delivery. Propranolol HCl containing tablets with Kollidon SR as an excipient for direct compression and different Kollicoat SR 30 D/Kollicoat IR coats varying from 10 to 20mg polymer/cm2 were investigated regarding drug release in 0.1N HCl. Furthermore, the onset of floating, the floating duration and the floating strength of the device were determined. In addition, benchtop MRI studies of selected samples were performed. Coated tablets with 10mg polymer/cm2 SR/IR, 8.5:1.5 coat exhibited the shortest lag times prior to drug release and floating onset, the fastest increase in and highest maximum values of floating strength. The drug release was delayed efficiently within a time interval of 24 h by showing linear drug release characteristics. Poly(vinyl acetate) proved to be an appropriate excipient to ensure safe and reliable drug release. Floating strength measurements offered the possibility to quantify the floating ability of the developed systems and thus to compare different formulations more efficiently. Benchtop MRI studies allowed a deeper insight into drug release and floating mechanisms noninvasively and continuously.

IPN hydrogels based on PNIPAAm and PVA-Ma networks: characterization through measure of LCST, swelling ratio and mechanical properties - doi: 10.4025/actascitechnol.v34i2.15019

OpenAIRE

Wenceslau, Adriana Cristina; Universidade Estadual de Maringá - UEM; Rubira, Adley Forti; Universidade Estadual de Maringá - UEM; Muniz, Edvani Curti; UEM, Maringá, Paraná

2011-01-01

IPN hydrogels based on chemically modified poly(vinyl alcohol) (or PVA-Ma), with different degrees of substitution (DS), and poly(N-isopropylacrylamide) (or PNIPAAm) were obtained and characterized through measures of LCST, swelling ratio and mechanical properties. Linear PVA-Ma with several DS were obtained through the chemical reaction of PVA with glycidyl methacrylate (GMA). The DS of various PVA-Ma were determined through 1H NMR spectroscopy. Two steps were used for preparation the PVA-Ma...

Synthesis and characterization of porous microspheres bearing pyrrolidone units

Energy Technology Data Exchange (ETDEWEB)

Maciejewska, M., E-mail: mmacieje@umcs.pl; Kołodyńska, D.

2015-01-15

Porous microspheres of glycydyl methacrylate (GMA) cross-linked with trimethylolpropane trimethacrylate (TRIM) were prepared with toluene as porogen by suspension-emulsion polymerization. With increasing molar ratio of the functional monomer to cross-linker, the epoxy group content increases significantly whereas the parameters of porous structure (specific surface area and total pore volume) decreases. In order to obtain adsorbents bearing functional groups the porous methacrylate network was modified by subsequent reaction with pyrrolidone. The materials were studied using elemental analysis, infrared spectroscopy, atomic force microscopy (AFM), attenuated total reflection (ATR) spectroscopy, Raman spectroscopy, thermal gravimetry. Additionally, polymers sorption capacity towards Cu(II) was investigated. - Highlights: • Porous microspheres with reactive epoxy group were synthesized. • Highly developed porous structure was created. • Pyrrolidone units were incorporated during ring–opening reaction. • Polymers sorption capacity towards Cu (II) was investigated.

Radiation grafting of hydrophilic monomers on to plasticized poly(vinyl chloride) sheets: Pt. 1

International Nuclear Information System (INIS)

Kalliyana Krishnan, V.; Jayakrishnan, A.; Francis, J.D.

1990-01-01

Medical-grade plasticized polyvinyl chloride (PVC) sheets were surface modified using gamma-radiation grafting of a combination of hydrophilic monomers based on 2-hydroxyethyl methacrylate (HEMA) and N-vinyl pyrrolidone (NVP). The properties of the modified surfaces were evaluated using contact angle measurements, phase-contrast photomicroscopy and scanning electron microscopy. Surface energy calculations indicated that the surfaces became highly hydrophilic when grafted with even a 1% (v/v) solution of HEMA-NVP combination in the presence of 0.005 M CuSO 4 . Migration of the plasticizer di(2-ethylhexyl phthalate) from the grafted sheets was examined in hydrocarbon solvents such as n-hexane, n-heptane and n-octane and in extractant media such as cotton seed oil and polyethylene glycol-400 (PEG-400). The migration was found to be 0 C over a period of 5 h. Accelerated leaching studies in cotton seed oil and PEG-400 demonstrated that virtually no plasticizer migrated out in the former over a period of 96 h whereas the rate of migration in the latter medium showed only a mild reduction. The migration behaviour was Fickian in nature for grafted sheets. The method described may be useful as a simple, versatile technique for preventing plasticizer migration from plasticized PVC for medical applications. (author)

Thermodynamics of poly(7-methoxy-2-acetylbenzofurane methyl methacrylate-co-styrene) and poly(2-acetylbenzofurane methyl methacrylate-co-styrene)-probe interactions at different temperatures by inverse gas chromatography

International Nuclear Information System (INIS)

İlter, Zülfiye; Demir, Abdullah; Kaya, İsmet

2016-01-01

Highlights: • Thermodynamic of methacrylate-co-styrene polymers were studied by the inverse gas chromatography. • The sorption parameters of polymer-solute systems were determined under glass transition temperature of polymers. • The solubility parameter (δ 2 ) of the polymer was obtained from the slope and intercepts. • Flory-Huggins interaction parameter (χ 12 ∞ ) were determined for polymer-solute systems. - Abstract: In this study, some thermodynamic properties of poly(7-methoxy-2-acetylbenzofurane methyl methacrylate-co-styrene) Poly(MABMM-co-St) and poly(2-acetylbenzofurane methyl methacrylate-co-styrene) Poly(ABMM-co-St) were studied by the inverse gas chromatography (IGC) technique. The retention times (t r ) of selected organic probes were determined from the interactions with Poly(MABMM-co-St) and Poly(ABMM-co-St) of four groups of solvents with different chemical natures and polarities. Then, specific volume (V g 0 ) values of probes were calculated at different column temperatures. The glass transition temperatures (T g ) of Poly(MABMM-co-St) and Poly(ABMM-co-St) were found as 393, 413 K from inverse gas chromatography measurements, respectively. Under the glass transition temperatures adsorption heat (ΔH a ) and above the glass transition molar heat (ΔH 1 S ), free energies (ΔG 1 S ) and entropies (ΔS 1 S ) belonging to sorption for every probe were calculated from inverse gas chromatography measurements. The partial molar heat (ΔH 1 ∞ ), partial molar free energy (ΔG 1 ∞ ), Flory-Huggins interaction parameter (χ 12 ∞ ) and weight fraction activity coefficient (a 1 /w 1 ) ∞ , values for infinite dilute solutions were calculated for polymer-probe systems. The solubility parameter (δ 2 ) of the polymer was obtained from the slope and intercepts of Flory-Huggins interaction parameter (χ 12 ∞ ) graphs with solubility parameters (δ 1 ) of probes.

Nanoscale Characterization of Glass Flake Filled Vinyl Ester Anti-Corrosion Coatings

Directory of Open Access Journals (Sweden)

Salim Barbhuiya

2017-08-01

Full Text Available Vinyl ester is a thermoset matrix resin that is widely used in the coating industry. The presence of glass flakes further enhances the anti-corrosion performance of this coating. This paper reports the nanoscaled characterization of glass flake filled vinyl ester anti-corrosion coatings on mild steel. Bond strength properties of one uncoated and four coated samples with different thicknesses (300, 600, 900 and 1200 μm were studied using nanoscratch technique and ASTM Standard Test. It was found that the bond strength of coating with thickness 900 μm was the highest. The frequency distributions of elastic modulus on coating with 900 μm thickness determined using nanoindentation indicated that only 20–25% of the coating is composed of glass flakes and the balance is vinyl ester matrix. The critical depth at which the material is subject to failure due to external load and abrasion, was found to be around 100 nm.

Influence of acrylonitrile butadiene rubber on recyclability of blends prepared from poly(vinyl chloride) and poly(methyl methacrylate).

Science.gov (United States)

Suresh, Sunil S; Mohanty, Smita; Nayak, Sanjay K

2018-06-01

The current investigation deals with the recycling possibilities of poly(vinyl chloride) and poly(methyl methacrylate) in the presence of acrylonitrile butadiene rubber. Recycled blends of poly(vinyl chloride)/poly(methyl methacrylate) are successfully formed from the plastic constituents, those are recovered from waste computer products. However, lower impact performance of the blend and lower stability of the poly(vinyl chloride) phase in the recycled blend restricts its further usage in industrial purposes. Therefore, effective utilisation acrylonitrile butadiene rubber in a recycled blend was considered for improving mechanical and thermal performance. Incorporation of acrylonitrile butadiene rubber resulted in the improvement in impact performance as well as elongation-at-break of the recycled blend. The optimum impact performance was found in the blend with 9 wt% acrylonitrile butadiene rubber, which shows 363% of enhancement as compared with its parent blend. Moreover, incorporated acrylonitrile butadiene rubber also stabilises the poly(vinyl chloride) phase present in the recycled blend, similarly Fourier transform infrared spectroscopy studies indicate the interactions of various functionalities present in the recycled blend and acrylonitrile butadiene rubber. In addition to this, thermogravimetric analysis indicates the improvement in the thermal stability of the recycled blend after the addition of acrylonitrile butadiene rubber into it. The existence of partial miscibility in the recycled blend was identified using differential scanning calorimetry and scanning electron microscopy.

Environmentally benign formation of polymeric microspheres by rapid expansion of supercritical carbon dioxide solution with a nonsolvent.

Science.gov (United States)

Matsuyama, K; Mishima, K; Umemoto, H; Yamaguchi, S

2001-10-15

A novel method is reported for forming polymer microparticles, which reduce atmospheric emissions of environmentally harmful volatile organic compounds such as toluene and xylene used as paint solvent in paint industry. The polymer microparticles have formed through rapid expansion from supercritical solution with a nonsolvent (RESS-N). Solubilization of poly(styrene)-b-(poly(methyl methacrylate)-co-poly (glycidyl methacrylate)) copolymer(PS-b-(PMMA-co-PGMA), MW = 5000, PS/PMMA/PGMA = 2/5/3), poly(ethylene glycol) (PEG, M. W = 4000), bisphenol A type epoxy resin (EP, MW = 3000), poly(methyl methacrylate) (PMMA; MW = 15000, 75000, 120000), and poly(oxyalkylene) alkylphenyl ether (MW = 4000) in carbon dioxide (CO2) was achieved with the use of small alcohols as cosolvents. The solubility of the PS-b-(PMMA-co-PGMA) is extremely low in either CO2 or ethanol but becomes 20 wt % in a mixture of the two. Because ethanol is a nonsolvent for the polymer, it can be used as a cosolvent in rapid expansion from supercritical solution to produce 1-3 microm particles that do not agglomerate. Obtained polymer particles by RESS-N were applied as powder coatings. The resulting coatings have a smooth and coherent film. The particle size distribution of microspheres was controlled by changing the polymer concentration, preexpansion pressure, temperature, and injection distance. The feed compositions were more effective than the other factors in controlling the particle size. The polymeric microparticles formed by RESS-N method can be utilized to make the thin coating film without anytoxic organic solvents and/or surfactants.

Macroporous modified poly (vinyl alcohol) hydrogels with charged groups for tissue engineering: Preparation and in vitro evaluation

Energy Technology Data Exchange (ETDEWEB)

Drozdova, Maria G., E-mail: drozdovamg@gmail.com [Polymers for Biology Laboratory, Shemyakin & Ovchinnikov Institute of Bioorganic Chemistry of Russian Academy of Sciences, Miklukho-Maklaya str., 16/10, Moscow 117997 (Russian Federation); Zaytseva-Zotova, Daria S. [Polymers for Biology Laboratory, Shemyakin & Ovchinnikov Institute of Bioorganic Chemistry of Russian Academy of Sciences, Miklukho-Maklaya str., 16/10, Moscow 117997 (Russian Federation); Akasov, Roman A. [Polymers for Biology Laboratory, Shemyakin & Ovchinnikov Institute of Bioorganic Chemistry of Russian Academy of Sciences, Miklukho-Maklaya str., 16/10, Moscow 117997 (Russian Federation); Sechenov First Moscow State Medical University, Institute for Regenerative Medicine, Trubetskaya str., 8/2, Moscow 119048 (Russian Federation); Golunova, Anna S.; Artyukhov, Alexander A. [D. Mendeleyev University of Chemical Technology of Russia, Miusskaya Square 9, Moscow 125047 (Russian Federation); Udartseva, Olga O.; Andreeva, Elena R. [Institute of Biomedical Problems of Russian Academy of Sciences, Khoroshevskoe Shosse 76a, Moscow 123007 (Russian Federation); Lisovyy, Denis E.; Shtilman, Michael I. [D. Mendeleyev University of Chemical Technology of Russia, Miusskaya Square 9, Moscow 125047 (Russian Federation); Markvicheva, Elena A. [Polymers for Biology Laboratory, Shemyakin & Ovchinnikov Institute of Bioorganic Chemistry of Russian Academy of Sciences, Miklukho-Maklaya str., 16/10, Moscow 117997 (Russian Federation)

2017-06-01

Poly(vinyl alcohol) (PVA) hydrogels are widely employed for various biomedical applications, including tissue engineering, due to their biocompatibility, high water solubility, low protein adsorption, and chemical stability. However, non-charged surface of PVA-based hydrogels is not optimal for cell adhesion and spreading. Here, cross-linked macroporous hydrogels based on low molecular weight acrylated PVA (Acr-PVA) was synthesized by modification of the pendant alcohol groups on the PVA with glycidyl methacrylate (GMA). To enhance cell affinity, charged groups were introduced to the hydrogel composition. For this purpose, Acr-PVA was copolymerized with either negatively charged acrylic acid (AA) or positively charged 2-(diethylamino) ethyl methacrylate (DEAEMA) monomers. A surface charge of the obtained hydrogels was found to be in function of the co-monomer type and content. Confocal microscopy observations confirmed that adhesion and spreading of both mouse fibroblasts (L929) and human mesenchymal stem cells (hMSC) on the modified Acr-PVA-AA and Acr-PVA-DEAEMA hydrogels were better than those on the non-modified Acr-PVA hydrogel. The increase of DEAEMA monomer content from 5 to 15 mol% resulted in the enhancement of cell viability which was 1.5-fold higher for Acr-PVA-DEAEMA-15 hydrogel than that of the non-modified Acr-PVA hydrogel sample. - Highlights: • To enhance cell affinity, acrylated PVA hydrogel was modified with AA or DEAEMA monomers. • Cell adhesion and spreading were found to depend on the co-monomer type and content. • Proliferation of L929 fibroblasts and stem cells increased on the modified hydrogels.

Macroporous modified poly (vinyl alcohol) hydrogels with charged groups for tissue engineering: Preparation and in vitro evaluation

International Nuclear Information System (INIS)

Drozdova, Maria G.; Zaytseva-Zotova, Daria S.; Akasov, Roman A.; Golunova, Anna S.; Artyukhov, Alexander A.; Udartseva, Olga O.; Andreeva, Elena R.; Lisovyy, Denis E.; Shtilman, Michael I.; Markvicheva, Elena A.

2017-01-01

Poly(vinyl alcohol) (PVA) hydrogels are widely employed for various biomedical applications, including tissue engineering, due to their biocompatibility, high water solubility, low protein adsorption, and chemical stability. However, non-charged surface of PVA-based hydrogels is not optimal for cell adhesion and spreading. Here, cross-linked macroporous hydrogels based on low molecular weight acrylated PVA (Acr-PVA) was synthesized by modification of the pendant alcohol groups on the PVA with glycidyl methacrylate (GMA). To enhance cell affinity, charged groups were introduced to the hydrogel composition. For this purpose, Acr-PVA was copolymerized with either negatively charged acrylic acid (AA) or positively charged 2-(diethylamino) ethyl methacrylate (DEAEMA) monomers. A surface charge of the obtained hydrogels was found to be in function of the co-monomer type and content. Confocal microscopy observations confirmed that adhesion and spreading of both mouse fibroblasts (L929) and human mesenchymal stem cells (hMSC) on the modified Acr-PVA-AA and Acr-PVA-DEAEMA hydrogels were better than those on the non-modified Acr-PVA hydrogel. The increase of DEAEMA monomer content from 5 to 15 mol% resulted in the enhancement of cell viability which was 1.5-fold higher for Acr-PVA-DEAEMA-15 hydrogel than that of the non-modified Acr-PVA hydrogel sample. - Highlights: • To enhance cell affinity, acrylated PVA hydrogel was modified with AA or DEAEMA monomers. • Cell adhesion and spreading were found to depend on the co-monomer type and content. • Proliferation of L929 fibroblasts and stem cells increased on the modified hydrogels.

Determination and modeling of binary and ternary solid-liquid phase equilibrium for the systems formed by 1,8-dinitronaphthalene and 1,5-dinitronaphthalene and N-methyl-2-pyrrolidone

International Nuclear Information System (INIS)

Xie, Yong; Du, Cunbin; Cong, Yang; Wang, Jian; Han, Shuo; Zhao, Hongkun

2016-01-01

Highlights: • SLE formed by 1,5 and/or 1,8-dinitronaphthalene and NMP was determined. • The binary and ternary phase diagrams were constructed. • The phase diagrams were correlated and calculated using thermodynamic models. - Abstract: The solubility of 1,8-dinitronaphthalene and 1,5-dinitronaphthalene in N-methyl-2-pyrrolidone at (293.15–343.15) K and the mutual solubility of the ternary 1,5-dinitronaphthalene + 1,8-dinitronaphthalene + N-methyl-2-pyrrolidone mixture at (313.15, 328.15 and 343.15) K were determined experimentally using the isothermal saturation method under atmospheric pressure (101.2 kPa). The solubility of 1,8-dinitronaphthalene in N-methyl-2-pyrrolidone is larger than that of 1,5-dinitronaphthalene. Three isothermal ternary phase diagrams were built according to the measured mutual solubility data. In each ternary phase diagram, there were one co-saturated point, two boundary curves, and three crystalline regions. Two pure solids (pure 1,8-dinitronaphthalene and pure 1,5-dinitronaphthalene) were formed in the ternary system at a given temperature, which were identified by Schreinemaker’s method of wet residue and powder X-ray diffraction (PXRD) pattern. The crystallization region of 1,8-dinitronaphthalene was smaller than that of 1,5-dinitronaphthalene at each temperature. The modified Apelblat equation, λh equation, NRTL model and Wilson model were used to correlate the solubility of 1,8-dinitronaphthalene and 1,5-dinitronaphthalene in N-methyl-2-pyrrolidone; and the NRTL and Wilson models were employed to correlate and calculate the mutual solubility for the ternary 1,5-dinitronaphthalene + 1,8-dinitronaphthalene + N-methyl-2-pyrrolidone system. The largest value of root-mean-square deviation (RMSD) was 20.34 × 10 −4 for the binary systems; and 7.38 × 10 −3 for ternary system. The calculated results via these models are all acceptable for the binary and ternary solid-liquid phase equilibrium.

The study of electron beam curing of coatings pt.2

International Nuclear Information System (INIS)

Pyun, H.C.; Park, W.B.; Kim, K.Y.; Seung, K.W.

1979-01-01

The reaction of methylmethacrylate-methacrylic acid copolymer with glycidyl methacrylate in the presence of trie triethylbenzyl ammonium chloride has been studied and compared with that of methylmethacrylate-glycidylmethacrylate with methacrylic acid. It was found that the addition reaction was in good agreement with second-order kinetics in regards to the structure of copolymers. The plausible reaction mechanism was proposed and elucidated on the basis of experimental data obtained. (author)

C, N co-doped TiO_2/TiC_0_._7N_0_._3 composite coatings prepared from TiC_0_._7N_0_._3 powder using ball milling followed by oxidation

International Nuclear Information System (INIS)

Hao, Liang; Wang, Zhenwei; Zheng, Yaoqing; Li, Qianqian; Guan, Sujun; Zhao, Qian; Cheng, Lijun; Lu, Yun; Liu, Jizi

2017-01-01

Highlights: • TiO_2/TiC_0_._7N_0_._3 coatings were prepared by ball milling followed by oxidation. • In situ co-doping of C and N with simultaneous TiO_2 formation was observed. • Improved photocatalytic activity under UV/visible light was noticed. • Synergism in co-doping and heterojunction formation promoted carrier separation. - Abstract: Ball milling followed by heat oxidation was used to prepared C, N co-doped TiO_2 coatings on the surfaces of Al_2O_3 balls from TiC_0_._7N_0_._3 powder. The as-prepared coatings were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrophotometer (UV–vis). The results show that continuous TiC_0_._7N_0_._3 coatings were formed after ball milling. C, N co-doped TiO_2/TiC_0_._7N_0_._3 composite coatings were prepared after the direct oxidization of TiC_0_._7N_0_._3 coatings in the atmosphere. However, TiO_2 was hardly formed in the surface layer of TiC_0_._7N_0_._3 coatings within a depth less than 10 nm during the heat oxidation of TiC_0_._7N_0_._3 coatings in carbon powder. Meanwhile, the photocatalytic activity evaluation of these coatings was conducted under the irradiation of UV and visible light. All the coatings showed photocatalytic activity in the degradation of MB no matter under the irradiation of UV or visible light. The C, N co-doped TiO_2/TiC_0_._7N_0_._3 composite coatings showed the most excellent performance. The enhancement under visible light irradiation should attribute to the co-doping of carbon and nitrogen, which enhances the absorption of visible light. The improvement of photocatalytic activity under UV irradiation should attribute to the synergistic effect of C, N co-doping, the formation of rutile-anatase mixed phases and the TiO_2/TiC_0_._7N_0_._3 composite microstructure.

Pesticidal seed coats based on azadirachtin-A: release kinetics, storage life and performance.

Science.gov (United States)

Nisar, Keyath; Kumar, Jitendra; Arun Kumar, M B; Walia, Suresh; Shakil, Najam A; Parsad, Rajender; Parmar, Balraj S

2009-02-01

Infestation of seeds by pests during storage leads to deterioration in quality. Seed coating is an effective option to overcome the menace. Unlike synthetic fungicidal seed coats, little is known of those based on botanicals. This study aims at developing azadirachtin-A-based pesticidal seed coats to maintain seed quality during storage. Polymer- and clay-based coats containing azadirachtin-A were prepared and evaluated for quality maintenance of soybean seed during storage. Gum acacia, gum tragacanth, rosin, ethyl cellulose, hydroxyethyl cellulose, polyethyl methacrylate, methyl cellulose, polyethylene glycol, polyvinyl chloride, polyvinyl acetate, polyvinyl pyrrolidone and Agrimer VA 6 polymers and the clay bentonite were used as carriers. The time for 50% release (t(1/2)) of azadirachtin-A into water from the seeds coated with the different coats ranged from 8.02 to 21.36 h. The half-life (T(1/2)) of azadirachtin-A in the coats on seed ranged from 4.37 to 11.22 months, as compared with 3.45 months in azadirachtin-A WP, showing an increase by a factor of nearly 1.3-3.3 over the latter. The coats apparently acted as a barrier to moisture to reduce azadirachtin-A degradation and prevented proliferation of storage fungi. Polyethyl methacrylate, polyvinyl acetate and polyvinyl pyrrolidone were significantly superior to the other polymers. Azadirachtin-A showed a significant positive correlation with seed germination and vigour, and negative correlation with moisture content. Effective polymeric carriers for seed coats based on azadirachtin-A are reported. These checked seed deterioration during storage by acting as a barrier to moisture and reduced the degradation of azadirachtin-A.

Antibacterial performance of polypropylene nonwoven fabric wound dressing surfaces containing passive and active components

Energy Technology Data Exchange (ETDEWEB)

Xin, Zhirong, E-mail: xinzhirong2012@126.com [School of Chemistry and Chemical Engineering, Yantai University, Yantai 264005 (China); Du, Shanshan; Zhao, Chunyu; Chen, Hao; Sun, Miao [School of Chemistry and Chemical Engineering, Yantai University, Yantai 264005 (China); Yan, Shunjie [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Luan, Shifang, E-mail: sfluan@ciac.ac.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Yin, Jinghua [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2016-03-01

Graphical abstract: - Highlights: • PNVP and PHMG components were covalently immobilized on PP{sub NWF} surface. • PP{sub NWF}-g-PNVP-PHMG possessed bacterial adhesion-resistant and bactericidal capabilities. • PP{sub NWF}-g-PNVP-PHMG obviously suppressed platelet and red blood cell adhesion. - Abstract: A growing number of wound dressing-related nosocomial infections necessitate the development of novel antibacterial strategies. Herein, polypropylene non-woven fabric (PP{sub NWF}) was facilely modified with passive and active antibacterial components, namely photografting polymerization both N-Vinyl-2-pyrrolidone (NVP) and glycidyl methacrylate (GMA) monomers, and the introduction of guanidine polymer through the reaction between active amino groups and epoxy groups. The modified samples were confirmed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), respectively. Water contact angle measurement, antibacterial test, platelet and red blood cell adhesion were used to evaluate the hydrophilicity, antibacterial properties and hemocompatibility of the samples. It was found that the antibacterial properties were obviously enhanced, meanwhile significantly suppressing platelet and red blood cell adhesion after the above modification. This PP{sub NWF} samples that possess antifouling and antimicrobial properties, have great potential in wound dressing applications.

Glycidyl methacrylate macroporous copolymer grafted with diethylene triamine as sorbent for Reactive Black 5

Directory of Open Access Journals (Sweden)

Sandić Zvjezdana P.

2014-01-01

Full Text Available In this paper, macroporous glycidyl methacrylate and ethylene glycol dimethacrylate copolymer functionalized with diethylene triamine [PGME-deta], was evaluated as Reactive Black 5 (RB5 sorbent. Batch RB5 removal from aqueous solution by PGME-deta was investigated by varying pH, contact time, sorbent dosage, initial dye concentration and temperature. The sorption is pH sensitive having maximum at pH 2 (dye removal of 85%, decreasing with the increase of pH (dye removal of 24% at pH=11 after 60 min. Sorption kinetics was fitted to chemical-reaction and particle-diffusion models (pseudo-first-order, pseudo-second-order, intraparticle diffusion and Mckay models. The pseudo-second-order kinetic model accurately predicted the RB5 amount sorbed under all investigated operating conditions, while the intraparticle diffusion was the dominant rate-limiting mechanism. The diffusion mechanism was more prevalent with the decrease in temperature and the increase in concentration. The isotherm data was best fitted with the Langmuir model, indicating homogeneous distribution of active sites on PGME-deta and monolayer sorption, with the maximum sorption capacity of 353 mg g-1. The calculated sorption rates improved with increasing temperature and an activation energy close to 40 kJ mol-1 was determined, suggesting that chemisorption was also rate-controlling. [Projekat Ministarstva nauke Republike Srbije, br. III 43009, br. TR 37021 i br. III 45001

Investigation of morphology and bioactive properties of composite coating of HA/vinyl acetate on pure titanium

International Nuclear Information System (INIS)

Afshar, Abdollahe; Yousefpour, Mardali; Xiudong, Yang; Li Xudong; Yang Bangcheng; Wu Yao; Chen Jiyong; Zhang Xingdong

2006-01-01

Electrochemical co-deposition approach was expanded to prepare composite bio-ceramic coating of hydroxyapatite (HA)/polyvinyl acetate on the surface of titanium. The role is to improve the bioactive and crystallization properties. The results of XRD, XPS, SEM and TEM characterization showed that by increasing amount of vinyl acetate in the composite bio-ceramic coating before and after immersing in the simulated body fluid (SBF), an oriented growth of HA planes on the (0 0 2) direction had been observed on titanium substrate. Also significant surface morphology changes were obtained

Synthesis and Application of Pyrrolidone-containing Shale Inhibitors

Science.gov (United States)

Liu, Yonggui; Hou, Jie; Zhang, Yang; Yan, Jing; Song, Tao; Xu, Yongjun

2018-03-01

New generation polyamine inhibitors are amino-terminated polyethers with excellent inhibiting capabilities; they play a key role in borehole stabilization and reservoir protection. However, polyamine inhibitors are limited by their poor thermal stability, which can be attributed to the presence of ether bonds in their molecular structures. We propose a three-step synthesis approach fora novel pyrrolidone-containing polyamine inhibitor (DYNP) by introducing N-vinyl-2-pyrrolidone (NVP) on divinyloxyethane. This polyamine inhibitor exhibits an optimized molecular structure and has enhanced heat resistance. Characterizations by infrared (IR) spectroscopy and evaluation tests demonstrate several advantages of DYNP inhibitors, including excellent inhibiting capability (superior to similar materials such as polyamines), improved heat resistance (reasonable stability at temperatures up to 240°C), and good compatibility with both fresh water and salt water drilling fluids. These can be attributed to the presence of considerable amounts of amino groups in the repeating unit of DYNP molecules. The DYNP inhibitor was applied in over 20 boreholes in tight oil blocks in Daqing Oilfield to relieve hydration of formations with high shale contents. For instance, drilling in the 2033.5m horizontal section of Dragon 2 borehole was smooth, with a borehole diameter expansion ratio below 10%.

Synthesis of asymmetric polyetherimide membrane for CO2/N2 separation

Science.gov (United States)

Ahmad, A. L.; Salaudeen, Y. O.; Jawad, Z. A.

2017-06-01

Large emission of carbon dioxide (CO2) to the environment requires mitigation to avoid unbearable consequences on global climate change. The CO2 emissions generated by fossil fuel combustion within the power and industrial sectors need to be quickly curbed. The gas emission can be abated using membrane technology; this is one of the most promising approaches for selective separation of CO2/N2. The purpose of the study is to synthesis an asymmetric polyetherimide (PEI) membrane and to establish its morphological characteristics for CO2/N2 separation. The PEI flat-sheet asymmetric membrane was fabricated using phase inversion with N-methyl-2-pyrrolidone (NMP) as solvent and water-isopropanol as a coagulant. Particularly, polymer concentration of 20, 25, and 30 wt. % were studied. In addition, the structure and morphology of the produced membrane were observed using scanning electron microscopy (SEM). Importantly, results showed that the membrane with high PEI concentration of 30 wt. % yield an optimal selectivity of 10.7 for CO2/Nitrogen (N2) separation at 1 bar and 25 ºC for pure gas, aided by the membrane surface morphology. The dense skin present was as a result of non-solvent (water) while isopropanol generates a porous sponge structure. This appreciable separation performance makes the PEI asymmetric membrane an attractive alternative for CO2/N2 separation.

Graft polymerization of vinyl acetate onto starch. Saponification to starch-g-poly(vinyl alcohol)

International Nuclear Information System (INIS)

Fanta, G.F.; Burr, R.C.; Doane, W.M.; Russell, C.R.

1979-01-01

Graft polymerizations of vinyl acetate onto granular cornstarch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinyl acetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. Over half of the polymer was present as ungrafted poly(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficency. Grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate--methyl methacrylate was carried out near 0 0 C; although conversion of monomers to polymer was low and grafted polymer contained 40 to 50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch-g-poly(vinyl acetate) to starch-g-poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch-g-poly(vinyl alcohol) in hot water was less than 50; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch-g-poly

Alanine/epr pellet dosimeter using poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) copolymer as a binder for radiation dosimetry

International Nuclear Information System (INIS)

Beshir, W.B.; Ezz El-Din, H.M.; Abdel-fatth, A.A.; Ebraheem, S.

2005-01-01

A new alanine pellet dosimeter was developed for gamma and electron beam radiation dosimetry. Alanine powder was mixed with a new binding material, poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) copolymer. Pellets were prepared by pressing fine powder alanine with 60% copolymer binder by using hydraulic press and a specially designed pressing die. The radiation-formed stable free radicals were analysed by using electron paramagnetic resonance (EPR) spectroscopy. The useful dose range of these pellets was found to ranges from 1 to 80 kGy. The stability of the radiation- induced response was also studied

Acrylic composition

International Nuclear Information System (INIS)

Kimura, Tadashi; Ozeki, Takao; Kobayashi, Juichi; Nakamoto, Hideo; Meda, Yutaka.

1969-01-01

An acrylic composition and a process for the production of an easily hardenable coating material by irradiating with active energy, particularly electron beams and ultraviolet light, are provided using a mixture of 10%-100% by weight of an unsaturated compound and 90%-0% of a vinyl monomer. The composition has a high degree of polymerization, low volatility, low viscosity and other properties similar to thermosetting acrylic or amino alkyd resins. The aforesaid unsaturated compound is produced by primarily reacting saturated cyclocarboxylic anhydride and/or alpha-, beta-ethylene unsaturated carboxylic anhydride and by secondarily reacting an epoxy radical-containing vinyl monomer by addition reaction with polyhydric alcohols. Each reaction is conducted in the presence of a tertiary amino radical-containing vinyl monomer as a catalyst. The cross-linking is effected generally with an electron beam accelerator of 0.1-2.0 MeV or with a light beam in the 2,000-8,000A range in the presence of a photosensitive agent. In one example, 62 parts of ethylene glycol and 196 parts of maleic anhydride were dissolved in a mixture consisting of 100 parts of n-butyl methacrylate and 30 parts of styrene. To the mixture were added 5 parts of 2-methyl 5 vinyl piridine and 0.005 part of hydroquinone monomethyl ether. After the reaction at 90 0 C for 3 hours, a compound HOC:O-CH=CHC:OCH 2 CH 2 C:OOH was produced. To this solution were added 285 parts of glycidyl methacrylate. After the reaction at 90 0 C for 6 hours, 95% of the carboxylic acids reacted with epoxy radicals. Fourteen examples are given. (Iwakiri, K.)

Preparation of Rhodamine B Fluorescent Poly(methacrylic acid Coated Gelatin Nanoparticles

Directory of Open Access Journals (Sweden)

Zhenhai Gan

2011-01-01

Full Text Available Poly(methacrylic acid (PMAA-coated gelatin nanoparticles encapsulated with fluorescent dye rhodamine B were prepared by the coacervation method with the aim to retard the release of rhodamine B from the gelatin matrix. With sodium sulfate as coacervation reagent for gelatin, a kind of biopolymer with excellent biocompatibility, the formed gelatin nanoparticles were cross-linked by formaldehyde followed by the polymerization of methacrylic acid coating. The fluorescent poly(methacrylic acid coated gelatin (FPMAAG nanoparticles had a uniform spherical shape and a size distribution of 60±5 nm. Infrared spectral analysis confirmed the formation of PMAA coating on the gelatin nanoparticles. Based on UV-Vis spectra, the loading efficiency of rhodamine B for the FPMAAG nanoparticles was 0.26 μg per mg nanoparticles. The encapsulated rhodamine B could sustain for two weeks. Favorable fluorescence property and fluorescence imaging of cells confirmed that the FPMAAG nanoparticles have promising biochemical, bioanalytical, and biomedical applications.

Radiation preparation of drug carriers based polyacrylic acid (PAAc) using poly(vinyl pyrrolidone) (PVP) as a template polymer

Science.gov (United States)

Abd El-Rehim, H. A.; Hegazy, E. A.; Khalil, F. H.; Hamed, N. A.

2007-01-01

The present study deals with the radiation synthesis of stimuli response hydrophilic polymers from polyacrylic acid (PAAc). To maintain the property of PAAc and control the water swellibility for its application as a drug delivery system, radiation polymerization of AAc in the presence of poly(vinyl pyrrolidone) (PVP) as a template polymer was carried out. Characterization of the prepared PAA/PVP inter-polymer complex was investigated by determining gel content, swelling property, hydrogel microstructure and the release rate of caffeine as a model drug. The release rate of caffeine from the PAA/PVP inter-polymer complexes showed pH-dependency, and seemed to be mainly controlled by the dissolution rate of the complex above a p Ka of PAAc. The prepared inter-polymer complex could be used for application as drug carriers.

Poly(vinyl-alcohol)/poly(ethylene-glycol)/poly(ethylene-imine) blend membranes - structure and CO2 facilitated transport

International Nuclear Information System (INIS)

Ben Hamouda, S.; Quang, Trong Nguyen; Langevin, D.; Sadok, Roudeslic

2010-01-01

Poly(vinyl-alcohol) (PVA)/poly(ethylene-imine) (PEI)/poly(ethylene-glycol) (PEG) blend membranes were prepared by solution casting followed by solvent evaporation. The effects of the blend polymer composition on the membrane structure and CO 2 /N 2 permeation characteristics were investigated. IR spectroscopy evidenced strong hydrogen bonding interactions between amorphous PVA and PEI, and weaker interactions between PVA and PEG. DSC studies showed that PVA crystallization was partially inhibited by the interactions between amorphous PVA and PEI blend, in which PEG separated into nodules. The CO 2 permeability decreased with an increase in CO 2 partial pressure in feed gas, while the N 2 permeability remained constant. This result indicated that only CO 2 was transported by the facilitated transport mechanism. The CO 2 and N 2 permeabilities increased monotonically with the PEI content in the blend membranes, whereas the ideal selectivity of CO 2 to N 2 transport showed a maximum. When CO 2 is humidified, its permeability through the blend membranes is much higher than that of dry CO 2 , but the change in permeability due to the presence of humidity is reversible. (authors)

Hydrogels based on chemically modified poly(vinyl alcohol (PVA-GMA and PVA-GMA/chondroitin sulfate: Preparation and characterization

Directory of Open Access Journals (Sweden)

E. C. Muniz

2012-05-01

Full Text Available This work reports the preparation of hydrogels based on PVA-GMA, PVA-GMA is poly(vinyl alcohol (PVA functionalized with vinyl groups from glycidyl methacrylate (GMA, and on PVA-GMA with different content of chondroitin sulfate (CS. The degrees of swelling of PVA-GMA and PVA-GMA/CS hydrogels were evaluated in distilled water and the swelling kinetics was performed in simulated gastric and intestinal fluids (SGF and SIF. PVA-GMA and PVAGMA/CS hydrogels demonstrated to be resistant on SGF and SIF fluids. The elastic modulus, E, of swollen-hydrogels were determined through compressive tests and, according to the obtained results, the hydrogels presented good mechanical properties. At last, the presence of CS enhances the hydrogel cell compatibility as gathered by cytotoxicity assays. It was concluded that the hydrogels prepared through this work presented characteristics that allow them to be used as biomaterial, as a carrier in drug delivery system or to act as scaffolds in tissue engineering as well.

Modification of flax fibres by radiation induced emulsion graft copolymerization of glycidyl methacrylate

International Nuclear Information System (INIS)

Moawia, Rihab Musaad; Nasef, Mohamed Mahmoud; Mohamed, Nor Hasimah; Ripin, Adnan

2016-01-01

Flax fibres were modified by radiation induced graft copolymerization of glycidyl methacrylate (GMA) by pre-irradiation method in an emulsion medium. The effect of reaction parameters on the degree of grafting (DOG) such as concentration of bleaching agent, absorbed dose, monomer concentration, temperature and reaction time were investigated. The DOG was found to be dependent on the investigated parameters. The incorporation of poly(GMA) grafts in the bleached flax fibres was confirmed by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The structural and mechanical changes were evaluated by X-ray diffraction (XRD) and mechanical tester, respectively. The results revealed that reacting bleached flax fibres irradiated with 20 kGy with 5% GMA emulsion containing 0.5% polyoxyethylene-sorbitan monolaurate (Tween 20) surfactant at 40 °C for 1 h led to a maximum DOG of 148%. The grafted fibres showed sufficient mechanical strength and hydrophobicity which make them promising precursors for development of adsorbents after appropriate chemical treatments. - Highlights: • Flax fibers were modified by radiation induced emulsion grafting of GMA. • Bleaching with 0.7 wt% Na-chlorite was essential for achieving high DOGs. • Effect of reaction parameters on the degree of grafting were established. • The incorporation of poly-GMA grafts was proved by SEM, FTIR and XRD. • The obtained poly-GMA grafted flax fibers have potential for adsorbent making.

Fabrication of poly(methyl methacrylate)-block-poly(methacrylic acid) diblock copolymer as a self-embrittling strippable coating for radioactive decontamination

International Nuclear Information System (INIS)

Liu Renlong; Zhang Huiyan; Li Yintao; Zhou Yuanlin; Zhang Quanping; Zheng Jian; Wang Shanqiang

2016-01-01

The poly(methyl methacrylate)-block-poly(methacrylic acid) diblock copolymer with different monomer compositions was synthesized via reversible addition-fragmentation chain transfer polymerization. Meanwhile, a novel self-embrittling strippable coating was prepared using the diblock copolymers, which is proposed to be used as radioactive decontamination agents without manual operation. Furthermore, the decontamination efficiencies of self-embrittling strippable coatings for radioactive contamination on glass, marble, and stainless steel surfaces were studied. (author)

Novel hybrid coatings with controlled wettability by composite nanoparticle aggregation

Energy Technology Data Exchange (ETDEWEB)

Hritcu, Doina, E-mail: dhritcu@ch.tuiasi.ro; Dodi, Gianina; Iordache, Mirabela L.; Draganescu, Dan; Sava, Elena; Popa, Marcel I.

2016-11-30

Highlights: • Magnetite-grafted chitosan composite nanoparticles were synthesized. • The particles are able to assemble under the influence of a silane derivative. • Thin films containing composites, chitosan and hydrolyzed silane were optimized. • The novel hybrid coatings show hierarchical roughness and high wetting angle. - Abstract: The aim of this study is to evaluate novel hybrid materials as potential candidates for producing coatings with hierarchical roughness and controlled wetting behaviour. Magnetite (Fe{sub 3}O{sub 4}) nanoparticles obtained by co-precipitation were embedded in matrices synthesized by radical graft co-polymerization of butyl acrylate (BA), butyl methacrylate (BMA), hexyl acrylate (HA) or styrene (ST) with ethylene glycol di-methacrylate (EGDMA) onto previously modified chitosan bearing surface vinyl groups. The resulting composite particles were characterized regarding their average size, composition and magnetic properties. Hybrid thin films containing suspension of composite particles in ethanol and pre-hydrolysed hexadecyltrimethoxysilane (HDTS) as a coupling/crosslinking agent were deposited by spin coating or spraying. The films were cured by heating and subsequently characterized regarding their morphology (scanning electron microscopy), contact angle with water and adhesion to substrate (scratch test). The structure-property relationship is discussed.

Inductive effect of poly(vinyl pyrrolidone) on morphology and photocatalytic performance of Bi{sub 2}WO{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Qiang; Chen, Jinxing; Xie, Yunyun; Wang, Mozhen; Ge, Xuewu, E-mail: xwge@ustc.edu.cn

2016-04-15

Graphical abstract: - Highlights: • PVP molecular chains will induce the assembly of the primary Bi{sub 2}WO{sub 6} nanosheets. • The assembly of primary Bi{sub 2}WO{sub 6} nanosheets forms various 3D topological structure. • Sheet-like, flower-like, red-blood-cell-like and square-pillar-like Bi{sub 2}WO{sub 6} were formed. • Bi{sub 2}WO{sub 6} formed at low concentration or molecular weight of PVP has better activity. - Abstract: Bi{sub 2}WO{sub 6} has great potential applications in the field of photocatalyst due to its excellent visible-light photocatalytic performance. This work studied the detailed morphological evolution of Bi{sub 2}WO{sub 6} particles synthesized in a simple hydrothermal system induced by the stabilizer poly(vinyl pyrrolidone) (PVP). The XRD and HRTEM results show PVP would not change the crystal structure of Bi{sub 2}WO{sub 6}, but the distribution of PVP on the initially formed Bi{sub 2}WO{sub 6} nanosheets will induce the crystal growth, resulting in a distinct morphology evolution of Bi{sub 2}WO{sub 6} with the increase of the concentration of PVP. At the same time, with the increase of the molecular weight of PVP, the morphology of Bi{sub 2}WO{sub 6} varied from simple sheet-like (S-BWO) to some complicated morphology, such as flower-like (F-BWO), red blood cell-like (B-BWO), and square-pillar-like (SP-BWO). The photocatalytic performances of Bi{sub 2}WO{sub 6} with various morphologies on the decomposition of RhB under visible light irradiation reveal that S-BWO has the best photocatalytic performance, while SP-BWO has the worst. This work not only gives the explanation of the inductive effect of PVP molecular chains on the morphological formation of Bi{sub 2}WO{sub 6} particles, but also provides the controllable way to the preparation of Bi{sub 2}WO{sub 6} with various morphologies taking advantage of the stabilizer PVP.

Adsorption of poly(vinyl formamide-co-vinyl amine) (PVFA-co-PVAm) polymers on zinc, zinc oxide, iron, and iron oxide surfaces.

Science.gov (United States)

Seifert, Susan; Simon, Frank; Baumann, Giesela; Hietschold, Michael; Seifert, Andreas; Spange, Stefan

2011-12-06

The adsorption of poly(vinyl formamide) (PVFA) and the statistic copolymers poly(vinyl formamide-co-vinyl amine) (PVFA-co-PVAm) onto zinc and iron metal particles as well as their oxides was investigated. The adsorbates were characterized by means of XPS, DRIFT spectroscopy, wet chemical analysis, and solvatochromic probes. Dicyano-bis-(1,10-phenanthroline)-iron(II) (1), 3-(4-amino-3-methylphenyl)-7-phenyl-benzo-[1,2-b:4,5-b']difuran-2,6-dione (2), and 4-tert-butyl-2-(dicyano-methylene)-5-[4-(diethylamino)-benzylidene]-Δ(3)-thiazoline (3) as solvatochromic probes were coadsorbed onto zinc oxide to measure various effects of surface polarity. The experimental findings showed that the adsorption mechanism of PVFA and PVFA-co-PVAm strongly depends on the degree of hydrolysis of PVFA and pH values and also on the kind of metal or metal oxide surfaces that were employed as adsorbents. The adsorption mechanism of PVFA/PVFA-co-PVAm onto zinc oxide and iron oxide surfaces is mainly affected by electrostatic interactions. Particularly in the region of pH 5, the adsorption of PVFA/PVFA-co-PVAm onto zinc and iron metal particles is additionally influenced by redox processes, dissolution, and complexation reactions. © 2011 American Chemical Society

Contact allergy to epoxy (meth)acrylates.

Science.gov (United States)

Aalto-Korte, Kristiina; Jungewelter, Soile; Henriks-Eckerman, Maj-Len; Kuuliala, Outi; Jolanki, Riitta

2009-07-01

Contact allergy to epoxy (meth)acrylates, 2,2-bis[4-(2-hydroxy-3-methacryloxypropoxy) phenyl]propane (bis-GMA), 2,2-bis[4-(2-hydroxy-3-acryloxypropoxy)phenyl]-propane (bis-GA), 2,2-bis[4-(methacryl-oxyethoxy)phenyl] propane (bis-EMA), 2,2-bis[4-(methacryloxy)phenyl]-propane (bis-MA), and glycidyl methacrylate (GMA) is often manifested together with contact allergy to diglycidyl ether of bisphenol A (DGEBA) epoxy resin. To analyse patterns of concomitant allergic reactions to the five epoxy (meth)acrylates in relation to exposure. We reviewed the 1994-2008 patch test files at the Finnish Institute of Occupational Health (FIOH) for reactions to the five epoxy (meth)acrylates, and examined the patients' medical records for exposure. Twenty-four patients had an allergic reaction to at least one of the studied epoxy (meth)acrylates, but specific exposure was found only in five patients: two bis-GMA allergies from dental products, two bis-GA allergies from UV-curable printing inks, and one bis-GA allergy from an anaerobic glue. Only 25% of the patients were negative to DGEBA epoxy resin. The great majority of allergic patch test reactions to bis-GMA, bis-GA, GMA and bis-EMA were not associated with specific exposure, and cross-allergy to DGEBA epoxy resin remained a probable explanation. However, independent reactions to bis-GA indicated specific exposure. Anaerobic sealants may induce sensitization not only to aliphatic (meth)acrylates but also to aromatic bis-GA.

Isobaric (vapour + liquid) equilibrium for N-methyl-2-pyrrolidone with branched alcohols

International Nuclear Information System (INIS)

Gnanakumari, P.; Venkatesu, P.; Hsieh, C.-T.; Rao, M.V. Prabhakara; Lee, M.-J.; Lin, Ho-mu

2009-01-01

The (vapour + liquid) equilibrium (VLE) and boiling temperature measurements have been determined at 95.3 kPa as a function of composition for the binary liquid mixtures of N-methyl-2-pyrrolidone (NMP) with branched alcohols using a Swietoslawski-ebulliometer. The branched alcohols include 2-propanol, 2-butanol, 2-methyl-l- propanol, 2-methyl-2-propanol, and 3-methyl-l-butanol. The experimental temperature-composition (T-x) results were used to estimate Wilson parameters and then used to calculate the equilibrium vapour compositions and the excess Gibbs free energy at T = 298.15 K. The experimental temperature-composition (T, x) results were correlated with the Wilson, the NRTL and the UNIQUAC models. The experimental results are interpreted in terms of intermolecular interactions between constituent molecules

Drug loading optimization and extended drug delivery of corticoids from pHEMA based soft contact lenses hydrogels via chemical and microstructural modifications.

Science.gov (United States)

García-Millán, Eva; Koprivnik, Sandra; Otero-Espinar, Francisco Javier

2015-06-20

This paper proposes an approach to improve drug loading capacity and release properties of poly(2-hydroxyethyl methacrylate) (p(HEMA)) soft contact lenses based on the optimization of the hydrogel composition and microstructural modifications using water during the polymerization process. P(HEMA) based soft contact lenses were prepared by thermal or photopolymerization of 2-hydroxyethyl methacrylate (HEMA) solutions containing ethylene glycol di-methacrylate as crosslinker and different proportions of N-vinyl-2-pyrrolidone (NVP) or methacrylic acid (MA) as co-monomers. Transmittance, water uptake, swelling, microstructure, drug absorption isotherms and in vitro release were characterized using triamcinolone acetonide (TA) as model drug. Best drug loading ratios were obtained with lenses containing the highest amount (200 mM) of MA. Incorporation of 40% V/V of water during the polymerization increases the hydrogel porosity giving a better drug loading capacity. In vitro TA release kinetics shows that MA hydrogels released the drug significantly faster than NVP-hydrogels. Drug release was found to be diffusion controlled and kinetics was shown to be reproducible after consecutive drug loading/release processes. Results of p(HEMA) based soft contact lenses copolymerized with ethylene glycol dimethacrylate (EGDMA) and different co-monomers could be a good alternative to optimize the loading and ocular drug delivery of this corticosteroid drug. Copyright © 2015. Published by Elsevier B.V.

Rhodium/Silver-Cocatalyzed Transannulation of N-Sulfonyl-1,2,3-triazoles with Vinyl Azides: Divergent Synthesis of Pyrroles and 2 H-Pyrazines.

Science.gov (United States)

Zhang, Lin; Sun, Ge; Bi, Xihe

2016-11-07

The first cyclization reaction between vinyl azides and N-sulfonyl-1,2,3-triazoles is reported. A Rh/Ag binary metal catalyst system proved to be necessary for the successful cyclization. By varying the structure of vinyl azides, such reaction allows the divergent synthesis of pyrroles and 2H-pyrazines. The cyclization reactions feature a broad substrate scope, good functional group tolerance, high reaction efficiency, and good to high product yields. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development of swellable local implants of a polyethyleneimine-poly(vinyl pyrrolidone) (PEI-PVP) hydrogel as a socket filler.

Science.gov (United States)

Chang, Ching-Wen; Ho, Hsiu-O; Lo, Yi-June; Lee, Sheng-Yang; Yang, You-Ren; Sheu, Ming-Thau

2012-01-01

In this study, hydrogels composed of polyethyleneimine (PEI) and poly(vinyl pyrrolidone) K90 (PVP) cross-linked with various concentrations (0, 0.125, 0.25 and 0.5%) of glutaraldehyde were evaluated as a hydrogel filler for the local delivery of lidocaine after tooth extraction. The drug-release kinetics, swellability, cytotoxicity and wound healing after tooth extraction of these non-cross-linked and cross-linked PEI-PVP hydrogels were examined in male beagles and compared to values using Spongostan(®). Results demonstrated that the extent of cross-linking influenced the swelling of the resulting hydrogel, but the drug-release rates were similar. No significant changes were observed in gingival fibroblasts in contact with the PEI- PVP hydrogels or Spongostan(®). In the in vivo study, PEI-PVP hydrogels showed good retention in the socket for 2 days and showed comparable wound-healing rates within 2 weeks with those of Spongostan(®). In conclusion, PEI-PVP hydrogels are suitable for use as socket-dressing materials, and the release of local anaesthesia from PEI-PVP hydrogels can be sustained for a desirable period of time to prevent pain after a tooth extraction.

Factors influencing the preparation of silver-coated glass frit with polyvinyl-pyrrolidone

Science.gov (United States)

Xiang, Feng; Gan, Weiping

2018-01-01

In this work, a new electroless silver plating method for the synthesis of silver-coated glass frit composite powders with good morphology has been proposed and the polyvinyl-pyrrolidone (PVP) was used the activating agent. It was found that the weight ratio of PVP to glass frit affected the distribution and number of silver nanoparticles. Moreover, the loading capacity of the glass frit, the pH value and reaction temperature could influence the size of the silver nanoparticles and morphology of silver on the surface of glass frit. The as-prepared silver-coated glass frit was used to prepare a silver paste using an optimized process to form silver nanoparticles with uniform size and high density. The silver paste with silver-coated glass frit increased the photovoltaic conversion efficiency of silicon solar cells by 0.271% compared with the silver paste prepared with pure glass frit. The silver nanoparticles can promoted the precipitation of Ag crystallites on the silicon wafer. Therefore, the silver-coated glass frit can further optimize and enhance the electrical performance of solar cells.

Synthesis and characterization of core-shell gold nanoparticles with poly(vinyl pyrrolidone) from a new precursor salt

Science.gov (United States)

Behera, M.; Ram, S.

2013-02-01

In this article, we report a facile one-step chemical synthesis of gold (Au) nanoparticles (GNPs) from a new precursor salt i.e., gold hydroxide in the presence of poly(vinyl pyrrolidone) (PVP) polymer. The non-aqueous dispersion of GNPs was comprehensively characterized by UV-Visible, FTIR, zeta potential, and transmission electron microscope (TEM). A strong surface plasmon resonance band at 529 nm in the UV-Visible spectrum confirms the formation of GNPs in the Au colloid. The FTIR spectroscopic results showed that PVP molecules get chemisorbed onto the surface of GNP via O-atom of carbonyl group. A negative zeta potential of (-)16 mV reveals accumulation of nonbonding electrons of O-atom of carbonyl group of PVP molecules on the nanosurface of GNP. TEM images demonstrate a core-shell nanostructure with an Au-crystalline core covered by a thin amorphous PVP-shell. PVP-capped GNPs could be a potential candidate for bio-sensing, catalysis, and other applications.

Formation of interfacial network structure via photo-crosslinking in carbon fiber/epoxy composites

Directory of Open Access Journals (Sweden)

S. H. Deng

2014-07-01

Full Text Available A series of diblock copolymers (poly(n-butylacrylate-co-poly(2-hydroxyethyl acrylate-b-poly(glycidyl methacrylate ((PnBA-co-PHEA-b-PGMA, containing a random copolymer block PnBA-co-PHEA, were successfully synthesized by atom transfer radical polymerization (ATRP. After being chemically grafted onto carbon fibers, the photosensitive methacrylic groups were introduced into the random copolymer, giving a series of copolymers (poly(n-butylacrylate-co-poly(2-methacryloyloxyethyl acrylate-b-poly(glycidyl methacrylate((PnBA-co-PMEA-b-PGMA. Dynamic mechanical analysis indicated that the random copolymer block after ultraviolet (UV irradiation was a lightly crosslinked polymer and acted as an elastomer, forming a photo-crosslinked network structure at the interface of carbon fiber/epoxy composites. Microbond test showed that such an interfacial network structure greatly improved the cohesive strength and effectively controlled the deformation ability of the flexible interlayer. Furthermore, three kinds of interfacial network structures, i physical crosslinking by H-bonds, ii chemical crosslinking by photopolymerization, and iii interpenetrating crosslinked network by photopolymerization and epoxy curing reaction were received in carbon fiber/epoxy composite, depending on the various preparation processes.

Graft copolymerization of glycidyl methacrylate onto delignified kenaf fibers through pre-irradiation technique

International Nuclear Information System (INIS)

Sharif, Jamaliah; Mohamad, Siti Fatahiyah; Fatimah Othman, Nor Azilah; Bakaruddin, Nurul Azra; Osman, Hasnul Nizam; Güven, Olgun

2013-01-01

Glycidyl methacrylate grafted kenaf (GMA-g-Kenaf) was prepared by pre-irradiation grafting technique. Kenaf fibers were treated with different concentration of sodium chlorite solution before used as trunk polymer. Treated kenaf fibers were irradiated by electron beam followed by grafting reaction in GMA/water emulsion system. The degree of grafting was determined as a function of absorbed dose, reaction time, reaction temperature and concentration of monomer. The results showed that the lignin content was decreased from 14.3% to as low as 3.3% with the increased of sodium chlorite concentration. This was evidenced by SEM pictures which show the surface of treated kenaf fibers was cleaner and smoother compared to that of untreated one. The degree of grafting increased with the increase of absorbed dose, reaction temperature, reaction time and monomer concentration as well as with decreasing lignin content. Formation of graft copolymer was confirmed with SEM, FTIR analysis. The structural investigation by XRD showed that degree of crystallinity of graft copolymers decreased with the increase in degree of grafting. - Highlights: • We used kenaf fibers for radiation induce graft copolymerization with GMA. • Kenaf fibers was treated to remove lignin in order to increase grafting yield. • Treated kenaf fibers were graft copolymerize through preirradiation technique. • Optimum conditions for graft copolymerization of kenaf fibers were established. • Formation of graft copolymer is also confirmed with SEM, FTIR and XRD

Poly(N-isopropylacrylamide-co-methacrylic acid microgel stabilized copper nanoparticles for catalytic reduction of nitrobenzene

Directory of Open Access Journals (Sweden)

Farooqi Zahoor H.

2015-09-01

Full Text Available Poly(N-isopropylacrylamide-co-methacrylic acid microgels [p(NIPAM-co-MAAc] were synthesized by precipitation polymerization of N-isopropylacrylamide and methacrylic acid in aqueous medium. These microgels were characterized by dynamic light scattering and Fourier transform infrared spectroscopy. These microgels were used as micro-reactors for in situ synthesis of copper nanoparticles using sodium borohydride (NaBH4 as reducing agent. The hybrid microgels were used as catalysts for the reduction of nitrobenzene in aqueous media. The reaction was performed with different concentrations of cat­alyst and reducing agent. A linear relationship was found between apparent rate constant (kapp and amount of catalyst. When the amount of catalyst was increased from 0.13 to 0.76 mg/mL then kapp was increased from 0.03 to 0.14 min-1. Activation parameters were also determined by performing reaction at two different temperatures. The catalytic process has been discussed in terms of energy of activation, enthalpy of activation and entropy of activation. The synthesized particles were found to be stable even after 14 weeks and showed catalytic activity for the reduction of nitrobenzene.

Development of a P((MAA-co-NVP)-g-EG) Hydrogel Platform for Oral Protein Delivery: Effects of Hydrogel Composition on Environmental Response and Protein Partitioning.

Science.gov (United States)

Steichen, Stephanie; O'Connor, Colleen; Peppas, Nicholas A

2017-01-01

Hydrogels based upon terpolymers of methacrylic acid, N-vinyl pyrrolidone, and poly(ethylene glycol) are developed and characterized for their ability to respond to changes in environmental pH and to partition protein therapeutics of varying molecular weights and isoelectric points. P((MAA-co-NVP)-g-EG) hydrogels are synthesized with PEG-based cross-linking agents of varying length and incorporation densities. The composition is confirmed using FT-IR spectroscopy and shows peak shifts indicating hydrogen bonding. Scanning electron microscopy reveals microparticles with an irregular, planar morphology. The pH-responsive behavior of the hydrogels is confirmed under equilibrium and dynamic conditions, with the hydrogel collapsed at acidic pH and swollen at neutral pH. The ability of the hydrogels to partition model protein therapeutics at varying pH and ionic strength is evaluated using three model proteins: insulin, porcine growth hormone, and ovalbumin. Finally, the microparticles are evaluated for adverse interactions with two model intestinal cell lines and show minimal cytotoxicity at concentrations below 5 mg mL -1 . © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Extraction of pentylbenzene from high molar mass alkanes (C14 and C17) by N-methyl-2-pyrrolidone

International Nuclear Information System (INIS)

Fandary, Mohamed S.; Al-Jimaz, Adel S.; Al-Kandary, Jasem A.; Fahim, Mohamed A.

2006-01-01

Equilibrium tie line data have been determined for the two ternary liquid systems: {tetradecane, or heptadecane + pentylbenzene + N-methyl-2-pyrrolidone (NMP)} over a temperature range of (298 to 328) K. The two systems studied exhibit type I liquid + liquid phase diagram. The effect of temperature and n-alkane chain length upon solubility, selectivity, and distribution coefficients were investigated experimentally

C, N co-doped TiO{sub 2}/TiC{sub 0.7}N{sub 0.3} composite coatings prepared from TiC{sub 0.7}N{sub 0.3} powder using ball milling followed by oxidation

Energy Technology Data Exchange (ETDEWEB)

Hao, Liang, E-mail: haoliang@tust.edu.cn [Tianjin Key Lab of Integrated Design and On-line Monitoring for Light Industry & Food Machinery and Equipment, Tianjin (China); College of Mechanical Engineering, Tianjin University of Science & Technology, No. 1038 Dagu Nanlu, Hexi District, Tianjin 300222 (China); Wang, Zhenwei, E-mail: 1004329228@qq.com [School of Naval Architecture and Ocean Engineering, Harbin Institute of Technology, Weihai, No. 2, Wenhua West Road, Weihai 264209 (China); Zheng, Yaoqing, E-mail: 13612177268@163.com [College of Mechanical Engineering, Tianjin University of Science & Technology, No. 1038 Dagu Nanlu, Hexi District, Tianjin 300222 (China); Li, Qianqian, E-mail: 1482471595@qq.com [College of Mechanical Engineering, Tianjin University of Science & Technology, No. 1038 Dagu Nanlu, Hexi District, Tianjin 300222 (China); Guan, Sujun, E-mail: sujunguan1221@gmail.com [College of Mechanical Engineering & Graduate School, Chiba University, 1-33, Yayoi-cho, Inage-ku, Chiba 263-8522 (Japan); Zhao, Qian, E-mail: zhaoqian@tust.edu.cn [Tianjin Key Lab of Integrated Design and On-line Monitoring for Light Industry & Food Machinery and Equipment, Tianjin (China); College of Mechanical Engineering, Tianjin University of Science & Technology, No. 1038 Dagu Nanlu, Hexi District, Tianjin 300222 (China); Cheng, Lijun, E-mail: chenglijun@tust.edu.cn [Tianjin Key Lab of Integrated Design and On-line Monitoring for Light Industry & Food Machinery and Equipment, Tianjin (China); College of Mechanical Engineering, Tianjin University of Science & Technology, No. 1038 Dagu Nanlu, Hexi District, Tianjin 300222 (China); Lu, Yun, E-mail: luyun@faculty.chiba-u.jp [College of Mechanical Engineering & Graduate School, Chiba University, 1-33, Yayoi-cho, Inage-ku, Chiba 263-8522 (Japan); Liu, Jizi, E-mail: jzliu@njust.edu.cn [Herbert Gleiter Institute of Nanoscience, Nanjing University of Science and Technology, No. 200, Xiaolingwei Street, Nanjing 210094 (China)

2017-01-01

Highlights: • TiO{sub 2}/TiC{sub 0.7}N{sub 0.3} coatings were prepared by ball milling followed by oxidation. • In situ co-doping of C and N with simultaneous TiO{sub 2} formation was observed. • Improved photocatalytic activity under UV/visible light was noticed. • Synergism in co-doping and heterojunction formation promoted carrier separation. - Abstract: Ball milling followed by heat oxidation was used to prepared C, N co-doped TiO{sub 2} coatings on the surfaces of Al{sub 2}O{sub 3} balls from TiC{sub 0.7}N{sub 0.3} powder. The as-prepared coatings were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrophotometer (UV–vis). The results show that continuous TiC{sub 0.7}N{sub 0.3} coatings were formed after ball milling. C, N co-doped TiO{sub 2}/TiC{sub 0.7}N{sub 0.3} composite coatings were prepared after the direct oxidization of TiC{sub 0.7}N{sub 0.3} coatings in the atmosphere. However, TiO{sub 2} was hardly formed in the surface layer of TiC{sub 0.7}N{sub 0.3} coatings within a depth less than 10 nm during the heat oxidation of TiC{sub 0.7}N{sub 0.3} coatings in carbon powder. Meanwhile, the photocatalytic activity evaluation of these coatings was conducted under the irradiation of UV and visible light. All the coatings showed photocatalytic activity in the degradation of MB no matter under the irradiation of UV or visible light. The C, N co-doped TiO{sub 2}/TiC{sub 0.7}N{sub 0.3} composite coatings showed the most excellent performance. The enhancement under visible light irradiation should attribute to the co-doping of carbon and nitrogen, which enhances the absorption of visible light. The improvement of photocatalytic activity under UV irradiation should attribute to the synergistic effect of C, N co-doping, the formation of rutile-anatase mixed phases and the TiO{sub 2}/TiC{sub 0.7}N{sub 0.3} composite microstructure.

Synthesis and characterization of poly(methyl methacrylate-co-vinyl acetate) and its evaluation as filtrate reducer; Sintese e caracterizacao de poli(metacrilato de metila-co-acetato de vinila) e sua avaliacao como redutor de filtrado

Energy Technology Data Exchange (ETDEWEB)

Nunes, Rita de Cassia P.; Pires, Renata V.; Segtovich, Iuri V.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, (UFRJ), RJ (Brazil)], e-mail: repires@ima.ufrj.br

2011-07-01

The drilling of petroleum well is extremely important and requires the use of suitable drilling fluids in order to ensure an efficient operation without causing rock damage. Specific polymers have been used in controlling infiltration during drilling, ensuring the operation success. In this work, spherical microparticles of poly(methyl methacrylate-co-vinyl acetate) (PMMA-VAc), prepared by suspension polymerization, were evaluated in terms of their performance in controlling filtrate loss of aqueous fluids. A filter press test with ceramic disc, simulating the rock, was used. The performance of the synthesized materials was compared to that of commercial polymers. It was observed that the performance of the material is directly associated to the relation between particle size and pore size of rock specimen. Furthermore, when the particle size is suitable, the rubbery characteristic of the material produces a more efficient filter cake, for filtrate control. (author)

Bone Regeneration Using N-Methyl-2-pyrrolidone as an Enhancer for Recombinant Human Bone Morphogenetic Protein-2 in a Rabbit Sinus Augmentation Model.

Science.gov (United States)

Lim, Hyun-Chang; Thoma, Daniel S; Yoon, So-Ra; Cha, Jae-Kook; Lee, Jung-Seok; Jung, Ui-Won

2017-01-01

The aim of this study was to determine whether N-methyl-2-pyrrolidone (NMP) can decrease the dose of recombinant human bone morphogenetic protein-2 (rhBMP-2) in sinus augmentation of rabbits. In each of 15 rabbits, 2 sinuses were randomly grafted using 1 of 3 treatment modalities: (i) biphasic calcium phosphate (BCP; control), (ii) rhBMP-2-coated BCP (BMP), or (iii) rhBMP-2-coated BCP soaked in NMP solution (BMP/NMP). The rabbits were sacrificed 2 weeks postoperatively. Histologic and histomorphometric analyses were performed. Bone formation in all groups was predominantly located close to the access window and the lateral walls. Newly formed bone within the total augmented area (NB TA ) was greatest in BMP/NMP (1.94 ± 0.69 mm 2 ), followed by BMP (1.50 ± 0.72 mm 2 ) and BCP (1.28 ± 0.52 mm 2 ) ( P > 0.05). In the center of the augmentation (NB ROI_C ) and the area close to the sinus membrane (NB ROI_M ), BMP/NMP produced the largest area of NB (NB ROI_C : 0.10 ± 0.11 mm 2 ; NB ROI_M : 0.17 ± 0.08 mm 2 ); the corresponding NB values for BCP were 0.05 ± 0.05 mm 2 and 0.08 ± 0.09 mm 2 , respectively ( P > 0.05 for all comparisons). The effect of NMP on bone regeneration was inconsistent between the specimens. Adding NMP as an adjunct to rhBMP-2-coated BCP produced inconsistent effects on bone regeneration, resulting in no significant benefit compared to controls.

Polymer and Water Dynamics in Poly(vinyl alcohol/Poly(methacrylate Networks. A Molecular Dynamics Simulation and Incoherent Neutron Scattering Investigation

Directory of Open Access Journals (Sweden)

Ester Chiessi

2011-10-01

Full Text Available Chemically cross-linked polymer networks of poly(vinyl alcohol/poly(methacrylate form monolitic hydrogels and microgels suitable for biomedical applications, such as in situ tissue replacement and drug delivery. In this work, molecular dynamics (MD simulation and incoherent neutron scattering methods are used to study the local polymer dynamics and the polymer induced modification of water properties in poly(vinyl alcohol/poly(methacrylate hydrogels. This information is particularly relevant when the diffusion of metabolites and drugs is a requirement for the polymer microgel functionality. MD simulations of an atomic detailed model of the junction domain at the experimental hydration degree were carried out at 283, 293 and 313 K. The polymer-water interaction, the polymer connectivity and the water dynamics were investigated as a function of temperature. Simulation results are compared with findings of elastic and quasi-elastic incoherent neutron scattering measurements, experimental approaches which sample the same space-time window of MD simulations. This combined analysis shows a supercooled water component and an increase of hydrophilicity and mobility with temperature of these amphiphilic polymer networks.

Comparison Study On Sunlight Or Gamma Radiation Aging Resistance Of Poly (Vinyl Pyrrolidone) Aqueous Solution With PVP Nanogel

International Nuclear Information System (INIS)

Doan Binh; Pham Thu Hong; Nguyen Nguyet Dieu; Nguyen Thanh Duoc

2011-01-01

Comparison study on sunlight or gamma-radiation aging resistance of poly (vinyl pyrrolidone) (PVP) aqueous solution with PVP nanogel at 0.5% was carried out. Sunlight or gamma- radiation aging resistance of PVP aqueous solution and nanogel was evaluated on the basis of their intrinsic viscosity, UV-VIS absorbance, weight averaged molecular weight (M w ). The PVP aqueous solution and nanogel exposed to sunlight in the storage duration of 3 months and to gamma radiation at absorbed doses of 0, 15, 30, 50 kGy were used for this study. Furthermore, the stability of PVP nanogel and of PVP aqueous solution was also studied on the change of their intrinsic viscosity, UV-VIS absorbance, weight averaged molecular weight, particle size distribution and coil size. The experimental results were shown that the aging resistance of PVP nanogel was higher than that of PVP aqueous solution when exposed to gamma radiation or sunlight. (author)

Determination of 5-hydroxy-N-methyl-2-pyrrolidone and 2-hydroxy-N-methylsuccinimide in human plasma and urine using liquid chromatography-electrospray tandem mass spectrometry.

Science.gov (United States)

Carnerup, M A; Akesson, B; Jönsson, B A

2001-09-15

A method for simultaneous determination of 5-hydroxy-N-methyl-2-pyrrolidone (5-HNMP) and 2-hydroxy-N-methylsuccinimide (2-HMSI) was developed. These compounds are metabolites from N-methyl-2-pyrrolidone (NMP), a powerful and widely used organic solvent. 5-HNMP and 2-HMSI were purified from plasma and urine by solid-phase extraction using Isolute ENV+ columns, and analysed by liquid chromatography coupled to a mass spectrometer fitted with an atmospheric pressure turbo ion spray ionisation interface in the positive ion mode. The method was validated for plasma and urine concentrations from 0.12 to 25 microg/ml. The recoveries for 5-HNMP and 2-HMSI in plasma were 99 and 98%, respectively, and in urine 111 and 106%, respectively. For 5-HNMP and 2-HMSI, the within-day precision in plasma was 1-4 and 3-6%, respectively, and in urine 2-12 and 3-10%, respectively. The corresponding data for the between-day precision was 5 and 3-6%, respectively, and 4-6 and 7-8%, respectively. The detection limit for 5-HNMP was 4 ng/ml in plasma and 120 ng/ml in urine. For 2-HMSI, it was 5 ng/ml in plasma and 85 ng/ml in urine. The method is applicable for analysis of plasma and urine samples from workers exposed to NMP.

The structure and properties of ZrN-Ni-Co-coatings on the edges steel knives of wood-cutting tools

International Nuclear Information System (INIS)

Chaevskij, V.V.; Grishkevich, A.A.; Zhilinskij, V.V.; Kuleshov, A.K.

2015-01-01

Modes were selected and formed electroplated Ni-Co-coatings, ion-plasma Zr N-coatings as well as combined Zr N-Ni-Co-coating on the edges steel (type R6M5) knives of wood-cutting milling tools. Formed electroplated Ni-Co-layers are not mixed with the steel substrate and the Zr N-coating. Microhardness of combined Zr N-Ni-Co-coatings is to 1,2-1,5 times more than microhardness of steel base and bare steel. When cutting laminated chipboard by steel knives of milling tool with a Ni-Co- and Zr N-Ni-Co-coatings under laboratory conditions, abrasive surface wear type of edges knives is observed. Calculating bulk wear of edges knives with Zr N-Ni-Co-coatings showed reduction of more than 3 times value in comparison with knives with Ni-Co-coatings. Pilot testing of tool modified with combined Zr N-Ni-Co-coatings at OJSC 'Minskdrev' when cutting pine confirmed relevance of the tests carried out, as well as showed an increase in durability period of cutters to 30% compared with bare tool. (authors)

Highly sensitive and ultrafast response surface acoustic wave humidity sensor based on electrospun polyaniline/poly(vinyl butyral) nanofibers

International Nuclear Information System (INIS)

Lin Qianqian; Li Yang; Yang Mujie

2012-01-01

Highlights: ► Polyanline/poly(vinyl butyral) nanofibers are prepared by electrospinning. ► Nanofiber-based SAW humidity sensor show high sensitivity and ultrafast response. ► The SAW sensor can detect very low humidity. - Abstract: Polyaniline (PANi) composite nanofibers were deposited on surface acoustic wave (SAW) resonator with a central frequency of 433 MHz to construct humidity sensors. Electrospun nanofibers of poly(methyl methacrylate), poly(vinyl pyrrolidone), poly(ethylene oxide), poly(vinylidene fluoride), poly(vinyl butyral) (PVB) were characterized by scanning electron microscopy, and humidity response of corresponding SAW humidity sensors were investigated. The results indicated that PVB was suitable as a matrix to form nanofibers with PANi by electrospinning (ES). Electrospun PANi/PVB nanofibers exhibited a core–sheath structure as revealed by transmittance electron microscopy. Effects of ES collection time on humidity response of SAW sensor based on PANi/PVB nanofibers were examined at room temperature. The composite nanofiber sensor exhibited very high sensitivity of ∼75 kHz/%RH from 20 to 90%RH, ultrafast response (1 s and 2 s for humidification and desiccation, respectively) and good sensing linearity. Furthermore, the sensor could detect humidity as low as 0.5%RH, suggesting its potentials for low humidity detection. Attempts were done to explain the attractive humidity sensing performance of the sensor by considering conductivity, hydrophilicity, viscoelasticity and morphology of the polymer composite nanofibers.

Robust Crosslinked Stereocomplexes and C60 Inclusion Complexes of Vinyl-Functionalized Stereoregular Polymers Derived from Chemo/Stereoselective Coordination Polymerization

KAUST Repository

Vidal, Fernando

2016-07-07

The successful synthesis of highly syndiotactic polar vinyl polymers bearing the reactive pendant vinyl group on each repeat unit, which is enabled by perfectly chemoselective and highly syndiospecific coordination polymerization of divinyl polar monomers developed through this work, has allowed the construction of robust crosslinked supramolecular stereocomplexes and C60 inclusion complexes. The metal-mediated coordination polymerization of three representative polar divinyl monomers, including vinyl methacrylate (VMA), allyl methacrylate (AMA), and N,N-diallyl acrylamide (DAA) by Cs-ligated zirconocenium ester enolate catalysts under ambient conditions exhibits complete chemoselectivity and high stereoselectivity, thus producing the corresponding vinyl-functionalized polymers with high (92% rr) to quantitative (>99% rr) syndiotacticity. A combined experimental (synthetic, kinetic, and mechanistic) and theoretical (DFT) investigation has yielded a unimetallic, enantiomorphic-site controlled propagation mechanism. Post-functionalization of the obtained syndiotactic vinyl-functionalized polymers via the thiol-ene click and photocuring reactions readily produced the corresponding thiolated polymers and flexible crosslinked thin film materials, respectively. Complexation of such syndiotactic vinyl-functionalized polymers with isotactic poly(methyl methacrylate) and fullerene C60 generates supramolecular crystalline helical stereocomplexes and inclusion complexes, respectively. Crosslinking of such complexes afforded robust crosslinked stereocomplexes that are solvent resistant and also exhibit considerably enhanced thermal and mechanical properties as compared to the uncrosslinked stereocompexes.

Robust Crosslinked Stereocomplexes and C60 Inclusion Complexes of Vinyl-Functionalized Stereoregular Polymers Derived from Chemo/Stereoselective Coordination Polymerization

KAUST Repository

Vidal, Fernando; Falivene, Laura; Caporaso, Lucia; Cavallo, Luigi; Chen, Eugene Y.-X.

2016-01-01

The successful synthesis of highly syndiotactic polar vinyl polymers bearing the reactive pendant vinyl group on each repeat unit, which is enabled by perfectly chemoselective and highly syndiospecific coordination polymerization of divinyl polar monomers developed through this work, has allowed the construction of robust crosslinked supramolecular stereocomplexes and C60 inclusion complexes. The metal-mediated coordination polymerization of three representative polar divinyl monomers, including vinyl methacrylate (VMA), allyl methacrylate (AMA), and N,N-diallyl acrylamide (DAA) by Cs-ligated zirconocenium ester enolate catalysts under ambient conditions exhibits complete chemoselectivity and high stereoselectivity, thus producing the corresponding vinyl-functionalized polymers with high (92% rr) to quantitative (>99% rr) syndiotacticity. A combined experimental (synthetic, kinetic, and mechanistic) and theoretical (DFT) investigation has yielded a unimetallic, enantiomorphic-site controlled propagation mechanism. Post-functionalization of the obtained syndiotactic vinyl-functionalized polymers via the thiol-ene click and photocuring reactions readily produced the corresponding thiolated polymers and flexible crosslinked thin film materials, respectively. Complexation of such syndiotactic vinyl-functionalized polymers with isotactic poly(methyl methacrylate) and fullerene C60 generates supramolecular crystalline helical stereocomplexes and inclusion complexes, respectively. Crosslinking of such complexes afforded robust crosslinked stereocomplexes that are solvent resistant and also exhibit considerably enhanced thermal and mechanical properties as compared to the uncrosslinked stereocompexes.

Surface characterization of poly(vinyl chloride) urinary catheters functionalized with acrylic acid and poly(ethylene glycol) methacrylate using gamma-radiation

Energy Technology Data Exchange (ETDEWEB)

Islas, Luisa [Departamento de Química de Radiaciones y Radioquímica, Instituto de Ciencias Nucleares, Universidad Nacional Autónoma de México, Ciudad Universitaria, Mexico D.F. 04510 (Mexico); Ruiz, Juan-Carlos [División de Ciencias Básicas e Ingeniería, Depto. de Ingeniería de Procesos e Hidráulica, Universidad Autónoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco No. 186, 09340 México D.F. (Mexico); Muñoz-Muñoz, Franklin [Facultad de Ingeniería, Arquitectura y Diseño, Universidad Autónoma de Baja California, Carretera Transpeninsular Ensenada-Tijuana 3917, Ensenada, B.C. C.P 22860 (Mexico); Isoshima, Takashi [Nano Medical Engineering Laboratory, RIKEN, 2-1Hirosawa, Wako, Saitama 351-0198 (Japan); Burillo, Guillermina, E-mail: burillo@nucleares.unam.mx [Departamento de Química de Radiaciones y Radioquímica, Instituto de Ciencias Nucleares, Universidad Nacional Autónoma de México, Ciudad Universitaria, Mexico D.F. 04510 (Mexico)

2016-10-30

Highlights: • Polymer grafting using gamma-radiation allowed for acrylic acid and poly(ethylene glycol) methacrylate to graft on the inner and outer surface of poly(vinyl chloride) urinary catheters. • HR-XPS revealed the different compositional percentages of the compounds present on the surface of the catheter. • Catheters that were grafted with PEGMA had the roughest surface as observed using scanning electron microscopy (SEM) and confocal laser microscopy (CLM). - Abstract: Poly(vinyl chloride) (PVC) urinary catheters were modified with either a single or binary graft of acrylic acid (AAc) and/or poly(ethylene glycol) methacrylate (PEGMA) using gamma-radiation from {sup 60}Co to obtain PVC-g-AAc, PVC-g-PEGMA, [PVC-g-AAc]-g-PEGMA, and [PVC-g-PEGMA]-g-AAc copolymers. The outer and inner surfaces of the modified catheters were characterized using scanning electron microscopy (SEM), confocal laser microscopy (CLM) and X-ray photoelectron spectroscopy (XPS). The XPS analyses, by examining the correlation between the variation of the C{sub 1s} and O{sub 1s} content at the catheter’s surface, revealed that the catheter’s surfaces were successfully grafted with the chosen compounds, with those that were binary grafted showing a slightly more covered surface as was evidenced by the disappearance of PVC’s Cl peak. The SEM and CLM analyses revealed that catheters that had been grafted with PEGMA had a rougher outer surface as compared to those that had only been grafted with AAc. In addition, these imaging techniques showed that the inner surface of the singly grafted catheters, whether they had been grafted with AAc or PEGMA, retained some smoothness at the analyzed grafting percentages, while the binary grafted catheters showed many protuberances and greater roughness on both outer and inner surfaces.

SPE-GC/FTD determination of N-methyl-2-pyrrolidone and its metabolites in urine.

Science.gov (United States)

Kubota, Ryuichi; Endo, Yoko; Takeuchi, Akito; Inoue, Yoshinori; Ogata, Hiroko; Ogawa, Masanori; Nakagawa, Tomoo; Onda, Nobuhiko; Endo, Ginji

2007-07-01

An analytical method using a combination of solid-phase extraction (SPE) and gas chromatography with a flame thermionic detector (GC/FTD) was developed for determination of N-methyl-2-pyrrolidone (NMP), N-methylsuccinimide (MSI), and 2-hydroxy-N-methylsuccinimide (2-HMSI) in human urine. The SPE cartridge of poly(divinylbenzene/hydroxymethacrylate) used was directly loaded with urine sample, followed by elution with methyl isobutyl ketone (MIBK) and subsequent centrifugation, and the supernatant was injected into the capillary GC using a DB1701. This method allowed efficient separation of NMP, MSI, and 2-HMSI, which were nearly free of interference by other GC peaks arising from urine. Recoveries of NMP, MSI, and 2-HMSI from the SPE cartridge were about 98, 101, and 67%, respectively, with limits of detection of 0.04, 0.02, and 0.06 mg/L, respectively, which met the regulatory requirements. The present method was used for assay in biological monitoring of workers exposed to NMP in their occupational environment.

Dermal absorption and urinary elimination of N-methyl-2-pyrrolidone.

Science.gov (United States)

Bader, Michael; Keener, Stephen A; Wrbitzky, Renate

2005-09-01

The dermal absorption of the solvent N-methyl-2-pyrrolidone (NMP) and its elimination in urine was investigated in an experimental study. Seven volunteers were exposed to 1045 mg of liquid NMP under occlusive conditions for 2 h. Urine was collected before, during and up to 72 h after the exposure and analysed for NMP by GC/MS after liquid-liquid extraction. Additionally, the remaining NMP in the pads was determined to estimate the total dermal uptake. The concentration of NMP in urine increased rapidly after beginning of the exposure up to 1 h after the exposure was completed. A peak concentration of 1,836+/-863 microg/l was observed, the half-life in urine was 3.2 h. About 0.5% of the absorbed dose was excreted metabolically unchanged. An average dermal absorption of 5.5 mg cm(-2) h(-1) was calculated. The results of this study show that the percutaneous absorption of NMP may contribute significantly to the overall uptake of the solvent, e.g. in the workplace. Therefore, a biological monitoring of NMP exposed workers is essential for occupational-medical surveillance.

Preparation and evaluation of poly(alkyl methacrylate-co-methacrylic acid-co-ethylene dimethacrylate) monolithic columns for separating polar small molecules by capillary liquid chromatography

Energy Technology Data Exchange (ETDEWEB)

Lin, Shu-Ling; Wu, Yu-Ru; Lin, Tzuen-Yeuan; Fuh, Ming-Ren, E-mail: msfuh@scu.edu.tw

2015-04-29

Highlights: • Methacrylic acid (MAA) was used to increase hydrophilicity of polymeric monoliths. • Fast separation of phenol derivatives was achieved in 5 min using MAA-incorporated column. • Separations of aflatoxins and phenicol antibiotics were achieved using MAA-incorporated column. - Abstract: In this study, methacrylic acid (MAA) was incorporated with alkyl methacrylates to increase the hydrophilicity of the synthesized ethylene dimethacrylate-based (EDMA-based) monoliths for separating polar small molecules by capillary LC analysis. Different alkyl methacrylate–MAA ratios were investigated to prepare a series of 30% alkyl methacrylate–MAA–EDMA monoliths in fused-silica capillaries (250-μm i.d.). The porosity, permeability, and column efficiency of the synthesized MAA-incorporated monolithic columns were characterized. A mixture of phenol derivatives is employed to evaluate the applicability of using the prepared monolithic columns for separating small molecules. Fast separation of six phenol derivatives was achieved in 5 min with gradient elution using the selected poly(lauryl methacrylate-co-MAA-co-EDMA) monolithic column. In addition, the effect of acetonitrile content in mobile phase on retention factor and plate height as well as the plate height-flow velocity curves were also investigated to further examine the performance of the selected poly(lauryl methacrylate-co-MAA-co-EDMA) monolithic column. Moreover, the applicability of prepared polymer-based monolithic column for potential food safety applications was also demonstrated by analyzing five aflatoxins and three phenicol antibiotics using the selected poly(lauryl methacrylate-co-MAA-co-EDMA) monolithic column.

Density, excess volume, and excess coefficient of thermal expansion of the binary systems of dimethyl carbonate with butyl methacrylate, allyl methacrylate, styrene, and vinyl acetate at T = (293.15, 303.15, and 313.15) K

International Nuclear Information System (INIS)

Wisniak, Jaime; Cortez, Gladis; Peralta, Rene D.; Infante, Ramiro; Elizalde, Luis E.; Amaro, Tlaloc A.; Garcia, Omar; Soto, Homero

2008-01-01

Densities of the binary systems of dimethyl carbonate with butyl methacrylate, allyl methacrylate, styrene, and vinyl acetate have been measured as a function of the composition at (293.15, 303.15, and 313.15) K at atmospheric pressure, using an Anton Paar DMA 5000 oscillating U-tube densimeter. The excess molar volumes are negative for the (dimethyl carbonate + vinyl acetate) system and positive for the three other binaries, and become more so as the temperature increases from (293.15 to 313.15) K. The apparent volumes were used to calculate the values of the partial excess molar volumes at infinite dilution. The excess coefficient of thermal expansion is positive for the four binary systems. The calculated excess molar volumes were correlated with the Redlich-Kister equation and with a series of Legendre polynomials. An explanation of the results is offered based on the FT-IR (ATR) spectra of several mixtures of the different systems

Density, excess volume, and excess coefficient of thermal expansion of the binary systems of dimethyl carbonate with butyl methacrylate, allyl methacrylate, styrene, and vinyl acetate at T = (293.15, 303.15, and 313.15) K

Energy Technology Data Exchange (ETDEWEB)

Wisniak, Jaime [Department of Chemical Engineering, Ben-Gurion University of the Negev, Beer-Sheva 84105 (Israel)], E-mail: wisniak@bgumail.bgu.ac.il; Cortez, Gladis; Peralta, Rene D.; Infante, Ramiro; Elizalde, Luis E. [Centro de Investigacion en Quimica Aplicada, Saltillo 25253, Coahuila (Mexico); Amaro, Tlaloc A.; Garcia, Omar; Soto, Homero [Facultad de Ciencias Quimicas, Universidad Autonoma de Coahuila, Saltillo 25280, Coahuila (Mexico)

2008-12-15

Densities of the binary systems of dimethyl carbonate with butyl methacrylate, allyl methacrylate, styrene, and vinyl acetate have been measured as a function of the composition at (293.15, 303.15, and 313.15) K at atmospheric pressure, using an Anton Paar DMA 5000 oscillating U-tube densimeter. The excess molar volumes are negative for the (dimethyl carbonate + vinyl acetate) system and positive for the three other binaries, and become more so as the temperature increases from (293.15 to 313.15) K. The apparent volumes were used to calculate the values of the partial excess molar volumes at infinite dilution. The excess coefficient of thermal expansion is positive for the four binary systems. The calculated excess molar volumes were correlated with the Redlich-Kister equation and with a series of Legendre polynomials. An explanation of the results is offered based on the FT-IR (ATR) spectra of several mixtures of the different systems.

Characterisation of Pristine and Recoated electron beam evaporation plasma-assisted physical vapour deposition Cr-N coatings on AISI M2 steel and WC-Co substrates

International Nuclear Information System (INIS)

Avelar-Batista, J.C.; Spain, E.; Housden, J.; Fuentes, G.G.; Rebole, R.; Rodriguez, R.; Montala, F.; Carreras, L.J.; Tate, T.J.

2005-01-01

This paper is focussed on the characterisation of electron beam evaporation plasma-assisted physical vapour deposition Cr-N coatings deposited on AISI M2 steel and hardmetal (K10) substrates in two different conditions: Pristine (i.e., coated) and Recoated (i.e., stripped and recoated). Analytical methods, including X-ray diffraction (XRD), scanning electron microscopy, scratch adhesion and pin-on-disc tests were used to evaluate several coating properties. XRD analyses indicated that both Pristine and Recoated coatings consisted of a mixture of hexagonal Cr 2 N and cubic CrN, regardless of substrate type. For the M2 steel substrate, only small differences were found in terms of coating phases, microstructure, adhesion, friction and wear coefficients between Pristine and Recoated. Recoated on WC-Co (K10) exhibited a less dense microstructure and significant inferior adhesion compared to Pristine on WC-Co (K10). The wear coefficient of Recoated on WC-Co was 100 times higher than those exhibited by all other specimens. The results obtained confirm that the stripping process did not adversely affect the Cr-N properties when this coating was deposited onto M2 steel substrates, but it is clear from the unsatisfactory tribological performance of Recoated on WC-Co that the stripping process is unsuitable for hardmetal substrates

Characterization of Ta–Si–N coatings prepared using direct current magnetron co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Chen, Yung-I, E-mail: yichen@mail.ntou.edu.tw; Lin, Kun-Yi; Wang, Hsiu-Hui; Cheng, Yu-Ru

2014-06-01

Ta–Si–N coatings were prepared using reactive direct current magnetron co-sputtering on silicon substrates. When the sputtering powers and N{sub 2} flow ratio were varied, Ta–Si–N coatings exhibited various chemical compositions and crystalline characteristics. The high-Si-content Ta–Si–N coatings exhibited an amorphous phase in the as-deposited states, whereas the low-Si-content coatings exhibited a face-centered cubic phase or an amorphous phase depending on the N content. This study evaluated the application of amorphous Ta–Si–N coatings, such as the protective coatings on glass molding dies, in high-temperature and oxygen-containing atmospheres for longed operation durations. To explore the oxidation resistance and mechanical properties of the Ta–Si–N coatings, annealing treatments were conducted in a 1%O{sub 2}–99%Ar atmosphere at 600 °C for 4–100 h. The material characteristics and oxidation behavior of the annealed Ta–Si–N coatings were examined using atomic force microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and a nanoindentation tester. The Si oxidized preferentially in the Ta–Si–N coatings. The in-diffusion of oxygen during 600 °C annealing was restricted by the formation of an amorphous oxide scale consisting of Si and O.

Radiation Induced Preparation of Polymer Membranes Grafted with Basic and Acidic Monomers for Application in Wastewater Treatment

Energy Technology Data Exchange (ETDEWEB)

Ajji, Z [Polymer Technology Division, Radiation Technology Department, Atomic Energy Commission of Syria (AECS), 17th Nissan Street, Kafar Sousah, Damascus (Syrian Arab Republic)

2012-09-15

Polymer membranes (PP and PE) had been grafted with basic and acidic functional groups using gamma radiation. Two binary mixtures had been used for the grafting reactions: acrylic acid/N-vinyl pyrrolidone, and acrylic acid/N-vinyl imidazole. The influence of different reaction parameters on the grafting yield had been investigated as: type of solvent and solvent composition, comonomer concentration and composition, addition of inhibitors, and dose. Water uptake with respect to the grafting yield had also been evaluated. The ability of PP films, grafted with acrylic acid/ vinyl pyrrolidone, to uptake heavy metal ions such as Hg{sup 2+}, Pb{sup 2+}, Cd{sup 2+}, Co{sup 2+}, Ni{sup 2+} and Cu{sup 2+} was elaborated. The uptake of the metal ions increases with increasing the grafting yield. Furthermore, the Pb{sup +2} uptake was much higher than the uptake of the Hg{sup 2+} and Cd{sup 2+} ions. The membranes may be considered for the separation of Pb{sup 2+} ions from Hg{sup 2+} or Cd{sup 2+} ions. Also the ability of PE films, grafted with acrylic acid/ N-vinyl imidazole to uptake heavy metal ions such as Pb{sup 2+}, Cd{sup 2+}, Co{sup 2+} and Ni{sup 2+} was elaborated. An increase in the uptake of the metal ions was observed as the grafting yield increased. (author)

Actinic-radiation curable polymers prepared from a reactive polymer, halogenated cyclic anhydride and glycidyl ester

International Nuclear Information System (INIS)

Pastor, S.D.

1979-01-01

A novel class of photosensitive polymers are disclosed which are prepared by the reaction, preferably in the presence of a catalyst, of a reactive polymer, a halogenated cyclic anhydride and glycidyl ester of an alpha, beta-unsaturated carboxylic acid. These polymers are capable of undergoing vinyl-type polymerization when exposed to actinic radiation

[Analysis of the character of film decomposition of methyl methacrylate (MMA) coated urea by infrared spectrum].

Science.gov (United States)

Li, Dong-po; Wu, Zhi-jie; Liang, Cheng-hua; Chen, Li-jun; Zhang, Yu-lan; Nie, Yan-xi

2012-03-01

The degradability characteristics of film with 4 kinds of methyl methacrylate coated urea amended with inhibitors were analyzed by FITR, which was purposed to supply theoretical basis for applying the FITR analysis method to film decomposition and methyl methacrylate coated urea fertilizers on farming. The result showed that the chemical component, molecule structure and material form of the membrane were not changed because of adding different inhibitors to urea. the main peaks of expressing film degradation process were brought by the -C-H of CH3 & CH2, -OH, C-O, C-C, C-O-C, C=O, C=C flexing vibrancy in asymmetry and symmetry in 3 479-3 195, 2 993--2 873, 1 741-1 564, 1 461-925 and 850-650 cm(-1). The peak value changed from smooth to tip, and from width to narrow caused by chemical structural transform of film The infrared spectrum of 4 kinds of fertilizers was not different remarkably before 60 days, and the film was slowly degraded. But degradation of the film was expedited after 60 days, it was most quickened at 120 day, and the decomposition rate of film was decreased at 310 day. The substantiality change of film in main molecule structure of 4 kinds of fertilizers didn't happen in 310 days. The main component of film materials was degraded most slowly in brown soil. The speed of film degradation wasn't heavily impacted by different inhibitors. The characteristic of film degradation may be monitored entirely by infrared spectrum. The degradation dynamic, chemical structure change, degradation speed difference of the film could be represented through infrared spectrum.

Mechanical, relaxation behavior and thermal degradation of UV irradiated poly(vinyl acetate)/poly( methyl methacrylate) blends

International Nuclear Information System (INIS)

Mansour, S.A.; Hafez, M.; Hussien, K.A.

2005-01-01

The effect of different doses of UV- irradiation on the mechanical and relaxation properties of poly(vinyl acetate)/poly(methyl methacrylate) blends were studied. Films of PVAc/PMMA blend with different contents were prepared using the casting technique. Also, PMMA could be blended with PVAc to improve its impact strength. Moreover UV-irradiation causes degradation of PVAc and formation of ketonic and aldehyde carbonyl groups according to a suggested scheme. Irradiation of PvAc/ PMMA blends causes a higher degree of degradation as compared to the PVAc alone although the PMMA is more susceptible than PVAc to the influence of radiation. Recognizable differences are observed for all parameters between the unirradiated and irradiated samples. Existence of a relaxation mechanism within the first 200s is reported. The shear modulus for all samples is also obtained and discussed. These data are used to calculate the strain energy density using the equation proposed by Blatzetal(1974 trans. Soc.Rheol. 18 145-61), based on the n-measure of Sethe

Corrosion characteristics of the Sm2(Fe0.9Co0.1)17N2.9 magnets stabilized by zinc-coating

International Nuclear Information System (INIS)

Arlot, R.; Machida, K.; Adachi, G.; Rango, P. de; Fruchart, D.

1998-01-01

The effect of powder particle size and of zinc coatings ( 2 (Fe 0.9 Co 0.1 ) 17 N 2.9 magnets has been investigated and compared to those obtained for Sm 2 Fe 17 N 3 and Nd 2 Fe 14 B magnets. Potentiokinetic polarisation behaviour in 0.5 N H 2 SO 4 and in Ringer's solution was studied. It was found that in 0.5 N H 2 SO 4 solution, the corrosion resistance is very weak, whereas in Ringer's solution, Zn coating and epoxy embedding provided a very efficient protection to the magnet. This result is quite unexpected as regarding the very weak amount of Zn (0.73 wt%) and epoxy (2.5-5 wt%) used to stabilize those very reactive ground powders which easily burn in air. Also, we characterized the magnetic properties of severely corroded magnets. (orig.)

Microstructures and properties of TiN reinforced Co-based composite coatings modified with Y_2O_3 by laser cladding on Ti–6Al–4V alloy

International Nuclear Information System (INIS)

Weng, Fei; Yu, Huijun; Chen, Chuanzhong; Liu, Jianli; Zhao, Longjie

2015-01-01

In this study, TiN reinforced composite coatings were fabricated on Ti–6Al–4V substrate by laser cladding with Co42 self-fluxing alloy, TiN and Y_2O_3 mixed powders. Microstructures and wear resistance of the cladding coatings with and without Y_2O_3 addition were investigated comparatively. Results showed that the coatings were mainly comprised of γ-Co/Ni, TiN, CoTi, CoTi_2, NiTi, TiC, Cr_7C_3, TiB, Ti_5Si_3 and TiC_0_._3N_0_._7 phases. The coatings showed metallurgical bonding free of pores and cracks with the substrate. Compared with the Ti–6Al–4V substrate, the microhardness and wear resistance of the coatings was enhanced by 3–4 times and 9.5–11.9 times, respectively. With 1.0 wt.% Y_2O_3 addition, the microstructure of the coating was refined significantly, and the microhardness and dry sliding wear resistance were enhanced further. The effects of Y_2O_3 were attributed to the residual Y_2O_3 and decomposed Y atoms. - Graphical abstract: The diagram illustration for the action mechanism of Y_2O_3: (a) dissolution of Y_2O_3 and TiN, (b) re-formation of TiN and in situ formation of TiC, (c) growth of TiN, TiC and the distribution of Y atoms. - Highlights: • Coatings showing metallurgical bonding with the substrate were fabricated. • The effect of Y_2O_3 on the refinement of the microstructure is notable. • A kind of Y_2O_3 centered core–shell structure was picked out in the coating. • Microhardness and wear resistance of the coatings was enhanced significantly.

Tensile properties of polymethyl methacrylate coated natural fabric Sterculia urens

CSIR Research Space (South Africa)

Jayaramudu, J

2009-04-01

Full Text Available stress, Young's modulus and % elongation at break were determined using a Universal Testing Machine. The effect of alkali treatment and the polymethyl methacrylate coating on tensile properties of the fabric was studied. The morphology of the fabric...

Production of sorption-active polypropylene fibers by radiation-induce grafting of glycidyl methacrylate as a precursor monomer

International Nuclear Information System (INIS)

Bondar, Yu.V.; Kim, H.J.; Lim, Y.J.; Kravets, L.I.

2004-01-01

Full text: Two types of sorption-active polypropylene fiber carrying strong-acid sulfonate groups and amino groups have been synthesized by radiation-induced graft polymerization of glycidyl methacrylate (GMA) with subsequent chemical modification of the epoxy groups of poly-GMA graft chains. The effect of various polymerization parameters on the GMA grafting degree was investigated in detail. The epoxy ring-opening of poly-GMA graft chains with introduction of strong-acid sulfonate groups was carried out with sodium hydrogen sulfite in water-dimethylformamide solution at 70 o C. The main peculiarities of the sulfonation reaction in depending on the reaction time and GMA grafting degree have been investigated. It was shown that for the samples with GMA grafting degree more than 50% two simultaneous processes take place during the sulfonation reaction, namely the incorporation of the sulfonate groups via opening of the GMA epoxy-rings as well as hydrolysis of the GMA epoxy-rings with the formation of α-glycol groups. Amine groups were incorporated by treatment of GMA-grafted polypropylene fibers with excess of diethylene triamine reagent. The conversion of the epoxy groups into the functional groups was investigated as a function of the degree of GMA grafting and reaction time. The ion-exchange characteristics of obtained sorption-active polypropylene fibers were determined

Production of sorption-active polypropylene fiber by radiation-induce grafting of glycidyl methacrylate as a precursor monomer

International Nuclear Information System (INIS)

Bondar, Yu.V.; Kim, H.J.; Lim, Y.J.; Kravets, L.I.

2004-01-01

Two types of sorption-active polypropylene fiber carrying strong-acid sulfonate groups and amino groups have been synthesized by radiation-induced graft polymerization of glycidyl methacrylate (GMA) with subsequent chemical modification of the epoxy groups of poly-GMA graft chains. The effect of various polymerization parameters on the GMA grafting degree was investigated in detail. The epoxy ring-opening of poly-GMA graft chains with introduction of strong-acid sulfonate groups was carried out with sodium hydrogen sulfite in water-dimethylformamide solution at 70 o C. The main peculiarities of the sulfonation reaction in depending on the reaction time and GMA grafting degree have been investigated. It was shown that for the samples with GMA grafting degree more than 50% two simultaneous processes take place during the sulfonation reaction, namely the incorporation of the sulfonate groups via opening of the GMA epoxy-rings as well as hydrolysis of the GMA epoxy-rings with the formation of α-glycol groups. Amine groups were incorporated by treatment of GMA-grafted polypropylene fibers with excess of diethylene triamine reagent. The conversion of the epoxy groups into the functional groups was investigated as a function of the degree of GMA grafting and reaction time. The ion-exchange characteristics of obtained sorption-active polypropylene fibers were determined. (author)

Enhanced mechanical properties of low-surface energy thin films by simultaneous plasma polymerization of fluorine and epoxy containing polymers

Energy Technology Data Exchange (ETDEWEB)

Karaman, Mustafa, E-mail: karamanm@selcuk.edu.tr [Department of Chemical Engineering, Selçuk University, Konya, 42075 (Turkey); Advanced Technology Research & Application Center, Selçuk University, Konya, 42075 (Turkey); Uçar, Tuba [Department of Chemical Engineering, Selçuk University, Konya, 42075 (Turkey)

2016-01-30

Graphical abstract: - Highlights: • Thin films of poly(hexafluorobutyl acrylate-glycidyl methacrylate) can be deposited by PECVD. • The coated surfaces are hydrophobic due to the long fluorinated side chains. • The hydrophobicity of the coating is observed to be stable under harsh conditions. • Film durability is attributed to the mechanical strength of the films due to their epoxide functionality. - Abstract: Thin films of poly(2,2,3,4,4,4 hexafluorobutyl acrylate-glycidyl methacrylate) (P(HFBA-GMA) were deposited on different surfaces using an inductively coupled RF plasma reactor. Fluorinated polymer was used to impart hydrophobicity, whereas epoxy polymer was used for improved durability. The deposition at a low plasma power and temperature was suitable for the functionalization of fragile surfaces such as textile fabrics. The coated rough textile surfaces were found to be superhydrophobic with water contact angles greater than 150° due to the high retention of long fluorinated side chains. The hydrophobicity of the surfaces was observed to be stable after many exposures to ultrasonification tests, which is attributed to the mechanical durability of the films due to their epoxide functionality. FTIR and XPS analyses of the deposited films confirmed that the epoxide functionality of the polymers increased with increasing glycidyl methacrylate fraction in the reactor inlet. The modulus and hardness values of the films also increase with increasing epoxide functionality.

[Monograph for N-Methyl-pyrrolidone (NMP) and human biomonitoring values for the metabolites 5-Hydroxy-NMP and 2-Hydroxy-N-methylsuccinimide].

Science.gov (United States)

2015-10-01

1-Methyl-pyrrolidone (NMP) is used as a solvent in many technical applications. The general population may be exposed to NMP from the use as ingredient in paint and graffiti remover, indoors also from use in paints and carpeting. Because of developmental toxic effects, the use of NMP in consumer products in the EU is regulated. The developmental effects accompanied by weak maternally toxic effects in animal experiments are considered as the critical effects by the German HBM Commission. Based on these effects, HBM-I values of 10 mg/l urine for children and of 15 mg/l for adults, respectively, were derived for the metabolites 5-Hydroxy-NMP and 2-Hydroxy-N-methylsuccinimide. HBM-II-values were set to 30 mg/l urine for children and 50 mg/l for adults, respectively. Because of similar effects of the structural analogue 1-ethyl-2-pyrrolidone (NEP), the possible mixed exposure to both compounds has to be taken into account when evaluating the total burden.

Composite poly(methyl methacrylate-methacrylic acid-2-hydroxyethyl methacrylate) latex for immunoassay. The case of plasminogen.

Science.gov (United States)

Miksa, B; Wilczynska, M; Cierniewski, C; Basinska, T; Slomkowski, S

1995-01-01

Poly(methyl methacrylate-methacrylic acid-2-hydroxyethyl methacrylate) latex (ACRYLAT) was synthesized by radical precipitation polymerization. The mass median diameter (MMD) and the geometrical standard deviation (GSD) of the ACRYLAT particles were 138 nm and 1.2, respectively. The concentration of the titrable carboxylic groups in the surface layer of latex particles was equal to 8.41 x 10(-6) mol m-2. Latex was able to bind up to 2.82 x 10(-7) mol of 1-aminopyrene per 1 m2 of the surface of the latex particles due to the ionic interactions between carboxylate anions and ammonium cations of protonated 1-aminopyrene. ACRYLAT was able to immobilize covalently human serum albumin in amounts up to 0.23 mg m-2. Aggregation of ACRYLAT with immobilized HSA, induced with specific antibodies (anti-HSA), was investigated turbidimetrically. The results indicated that in the model turbidimetric immunoassay, ACRYLAT coated with HSA can be used for the detection of anti-HSA in the goat anti-HSA serum diluted from 50 to 7000-fold. Immobilization of rabbit antibodies to plasminogen (anti-Plg) to ACRYLAT via the epsilon-aminocaproic acid linkers provided particles which were used for the development of the turbidimetric immunoassay for plasminogen. In this assay plasminogen could be detected in concentration ranging from 0.75 to 75 micrograms ml-1 in the blood plasma.

Extraction of pentylbenzene from high molar mass alkanes (C{sub 14} and C{sub 17}) by N-methyl-2-pyrrolidone

Energy Technology Data Exchange (ETDEWEB)

Fandary, Mohamed S. [Chemical Engineering Department, College of Technological Studies, P.O. Box 3242, Salmyiah 22033 (Kuwait)]. E-mail: mfandary@yahoo.com; Al-Jimaz, Adel S. [Chemical Engineering Department, College of Technological Studies, P.O. Box 3242, Salmyiah 22033 (Kuwait); Al-Kandary, Jasem A. [Chemical Engineering Department, College of Technological Studies, P.O. Box 3242, Salmyiah 22033 (Kuwait); Fahim, Mohamed A. [Chemical Engineering Department, University of Kuwait, P.O. Box 5969, Safat 13060 (Kuwait)

2006-04-15

Equilibrium tie line data have been determined for the two ternary liquid systems: {l_brace}tetradecane, or heptadecane + pentylbenzene + N-methyl-2-pyrrolidone (NMP){r_brace} over a temperature range of (298 to 328) K. The two systems studied exhibit type I liquid + liquid phase diagram. The effect of temperature and n-alkane chain length upon solubility, selectivity, and distribution coefficients were investigated experimentally.

Development of an amine-type adsorbent by electron beam-induced emulsion grafting of glycidyl methacrylate onto a nonwoven fabric

International Nuclear Information System (INIS)

Madrid, Jordan; Ueki, Yuji; Seko, Noriaki

2013-01-01

In the recent years, radiation-induced graft polymerization of various monomers onto different types of trunk polymers have been extensively used for researchers on adsorbents for cations, anions and different compounds, battery separators, antibacterial bandages, protein separators, and fuel cell applications. Some of these technologies were transferred to end-users and eventually commercialized. In most of these studies, a post-grafting reaction is performed to introduced chemical groups that impart functionality to the grafted material. In this paper, pre-irradiation technique was used for emulsion grafting of glycidyl methacrylate (GMA) onto an electron beam irradiated abaca-polyester nonwoven fabric (APNWF). The dependence of degree of grafting (Dg), calculated from the weight of APNWF before and after grafting, on irradiation dose, reaction time and monomer concentration were studies. After 50 kGy irradiation with 2 MeV electron beam and subsequent 3-hour reaction with an emulsion consisting of 5% GMA and 0.5% polyoxyethylene sorbitan monolaurate (Tween 20) surfactant in deionized water at 40 degree centegrade, a grafted APNWF with a Dg greater than 150% was obtained. The GMA grafted APNWF was further modified by reaction with ethylenediamine (EDA) in isopropyl alcohol at 60 degree centegrade to introduce amine functional groups. A 3-hour reaction with 50% EDA resulted to an amine group density of 2.7 mmole/gram-adsorbent. Preliminary batch adsorption experiments using Cu 2+ and Ni 2+ ions in aqueous solutions show that the adsorption capacity of the grafted adsorbent is four times greater for Cu 2+ ions compared to Ni 2+ ions. (author)

Monomer functionalized silica coated with Ag nanoparticles for enhanced SERS hotspots

Science.gov (United States)

Newmai, M. Boazbou; Verma, Manoj; Kumar, P. Senthil

2018-05-01

Mesoporous silica (SiO2) spheres are well-known for their excellent chromatographic properties such as the relatively high specific surface, large pore volume, uniform particle size, narrow pore size distribution with favorable pore connectivity; whereas the noble metal Ag nanoparticles have unique size/shape dependant surface plasmon resonance with wide ranging applications. Thus, the desire to synchronize both their properties for specific applications has naturally prompted research in the design and synthesis of core-shell type novel nanoAg@mesoSiO2 nanocomposites, which display potential utility in applications such as photothermal therapy, photocatalysis, molecular sensing, and photovoltaics. In the present work, SiO2 spheres were carefully functionalized with the monomer, N-vinyl pyrrolidone (NVP), which cohesively controls the uniform mass transfer of Ag+ metal ions, thereby enabling its sequential reduction to zerovalent Ag (in the presence of slightly excess NaOH) by electron transfer from nucleophilic attack of the NVP vinyl group by the water molecules even under ambient conditions. Complete metal nanoshell coverage of the silica surface was obtained after multiple Ag deposition cycles, as systematically confirmed from the BET, TEM, optical and FTIR characterization. Our present Ag-coated silica spheres were directly utilized as viable SERS substrates with high sensitivity in contrast with other long chain polymer/surfactant coated silica spheres, owing to the presence of significant number of nanogaps enhanced SERS 'hotspots', which were methodically analyzed utilizing two example analytes, such as crystal violet (CV) and calendula officinalis (CaF).

High temperature oxidation behaviour of nanostructured cermet coatings in a mixed CO2 - O2 environment

Science.gov (United States)

Farrokhzad, M. A.; Khan, T. I.

2014-06-01

Nanostructured ceramic-metallic (cermet) coatings composed of nanosized ceramic particles (α-Al2O3 and TiO2) dispersed in a nickel matrix were co-electrodeposited and then oxidized at 500°C, 600°C and 700°C in a mixed gas using a Thermo-gravimetric Analysis (TGA) apparatus. The mixed gas was composed of 15% CO2, 10% O2 and 75% N2. This research investigates the effects of CO2 and O2 partial pressures on time-depended oxidation rates for coatings and compared them to the results from atmospheric oxidation under similar temperatures. The increase in partial pressure of oxygen due to the presence of CO2 at each tested temperature was calculated and correlated to the oxidation rate of the coatings. The results showed that the presence of CO2 in the system increased the oxidation rate of cermet coatings when compared to atmospheric oxidation at the same temperature. It was also shown that the increase in the oxidation rate is not the result of CO2 acting as the primary oxidant but as a secondary oxidant which results in an increase of the total partial pressure of oxygen and consequently higher oxidation rates. The WDS and XRD analyses results showed that the presence of nanosized TiO2 particles in a nickel matrix can improve oxidation behaviour of the coatings by formation of Ni-Ti compounds on oxidizing surface of the coating which was found beneficiary in reducing the oxidation rates for cermet coatings.

DC conduction mechanism and dielectric properties of Poly (methyl methacrylate)/Poly (vinyl acetate) blends doped and undoped with malachite green

International Nuclear Information System (INIS)

Abd-El Kader, F.H.; Osman, W.H.; Hafez, R.S.

2013-01-01

Cast thin films of Poly (methyl methacrylate)/Poly (vinyl acetate) blends of different concentrations undoped and doped with malachite green have been prepared and subjected to both dc electrical conduction and dielectric spectroscopy measurements. The analysis of dc electrical conduction data showed that the space charge limited current mechanism has been dominant for Poly (vinyl acetate) while Schottky-Richardson conduction mechanism prevailed for the Poly (methyl methacrylate) and blended samples. The values of field lowering constant β and the thermal activation energy ΔE involved in the dc conduction were reported, which provide another support for the suggested Schottky-Richardson mechanism. The increase in current for the blend sample doped with malachite green has been attributed to the formation of charge transfer complexes inside the polyblend matrix. The dielectric constant as a function of temperature for all samples have been calculated which are affected by the composition ratio and the addition of dye. The relaxation peak that appeared in the dielectric loss curve at 347 K for the doped blend sample is related to local dipoles that are present in the dye material. The obtained relaxation process spectra present in the investigated samples were analyzed with the well-known model of Havriliak-Negami.

Surface modifying of microporous PTFE capillary for bilirubin removing from human plasma and its blood compatibility

International Nuclear Information System (INIS)

Jin Gu; Yao Qizhi; Zhang Shanzi; Zhang Lei

2008-01-01

In this study, human serum albumin (HSA) was covalently immobilized onto the inner surface of microporous poly(tetrafluoroethylene) (MPTFE) capillaries for direct bilirubin removal from human plasma. To obtain active binding sites for HSA, the MPTFE capillaries were chemically functionalized by using a coating of poly(vinyl alcohol) (PVA)-glycidyl methacrylate (GMA) copolymers. Characterization of grafted MPTFE capillaries was verified by XPS, Fourier transform infrared spectroscopy (FT-IR), scanning electronic microscopy (SEM). Non-specific adsorption on the PVA-GMA coated capillary remains low (< 0.38 mg bilirubin/g), and higher affinity adsorption capacity, of up to 73.6 mg bilirubin/g polymer was obtained after HSA is immobilized. Blood compatibility of the grafted MPTFE capillary was evaluated by SEM and platelet rich plasma (PRP) contacting experiments. The experimental data on blood compatibility indicated that PVA-coated and PVA-GMA-HSA coated PTFE capillary showed a sharp suppress on platelets adhesion. The proposed method has the potential of serving in bilirubin removal in clinical application

Characterization and temperature controlling property of TiAlN coatings deposited by reactive magnetron co-sputtering

International Nuclear Information System (INIS)

Chen, J.T.; Wang, J.; Zhang, F.; Zhang, G.A.; Fan, X.Y.; Wu, Z.G.; Yan, P.X.

2009-01-01

Titanium aluminum nitride (TiAlN) ternary coating is a potential material which is expected to be applied on satellite for thermal controlling. In order to investigate thermal controlling property, TiAlN coatings were deposited on Si wafers with different N 2 and Ar flux ratio by reactive magnetron co-sputtering. The structure, morphology, chemical composition and optical reflectance are investigated by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), atom force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and spectrophotometer, respectively. The orientation of the coatings depends on the N 2 /Ar flux ratio. The coatings deposited with N 2 /Ar ratio of 10, 30 and 60% show the cubic-TiN [2 2 0] preferred orientation and the coating deposited with N 2 /Ar ratio of 100% exhibits the phase of hexagonal-AlN and cubic-TiN. The surface of the coatings becomes more compact and smoother with the N 2 /Ar ratios increase. XPS spectrum indicates that the oxides (TiO 2 and Al 2 O 3 ), oxynitride (TiN x O y ) and nitrides (TiN and AlN x ) appear at the surface of the coatings. Ignoring internal power, the optimum equilibrium temperature of TiAlN coatings is 18 deg. C and the equilibrium temperature after heat-treated has slight change, which provides the prospective application on thermal controlling

Nanoclay filled hydrogels of poly (2-hydroxyethyl methacrylate-co-acrylamide) copolymers prepared by gamma radiation

International Nuclear Information System (INIS)

Rapado Paneque, M.; Matos Cause, W.; Barreras Gonzalez, G.; Griffith Perez, J.; Amalvy, J. I.; Van Espen, P.; Peniche, C.

2011-01-01

Hydrogels are polymers characterized by their ability to absorb a considerable amount of water. Hydrogels consist of polymer molecules physically or chemically crosslinked, forming a molecular network, so that in water they swell to an equilibrium value, preserving their shape [1]. The aim of this work was to prepare by gamma radiation poly (2-hydroxyethyl methacrylate-co-acrylamide) hydrogels, p(HEMA-co-AAm), doped with Nanoclay (laponite XLG). (Author)

Direct determination of N-methyl-2-pyrrolidone metabolites in urine by HPLC-electrospray ionization-MS/MS using deuterium-labeled compounds as internal standard.

Science.gov (United States)

Suzuki, Yoshihiro; Endo, Yoko; Ogawa, Masanori; Yamamoto, Shinobu; Takeuchi, Akito; Nakagawa, Tomoo; Onda, Nobuhiko

2009-11-01

N-methyl-2-pyrrolidone (NMP) has been used in many industries and biological monitoring of NMP exposure is preferred to atmospheric monitoring in occupational health. We developed an analytical method that did not include solid phase extraction (SPE) but utilized deuterium-labeled compounds as internal standard for high-performance liquid chromatography-electrospray ionization-mass spectrometry using a C30 column. Urinary concentrations of NMP and its known metabolites 5-hydoxy-N-methyl-2-pyrrolidone (5-HNMP), N-methyl-succinimide (MSI), and 2-hydroxy-N-methylsuccinimide (2-HMSI) were determined in a single run. The method provided baseline separation of these compounds. Their limits of detection in 10-fold diluted urine were 0.0001, 0.006, 0.008, and 0.03 mg/L, respectively. Linear calibration covered a biological exposure index (BEI) for urinary concentration. The within-run and total precisions (CV, %) were 5.6% and 9.2% for NMP, 3.4% and 4.2% for 5-HNMP, 3.7% and 6.0% for MSI, and 6.5% and 6.9% for 2-HMSI. The method was evaluated using international external quality assessment samples, and urine samples from workers exposed to NMP in an occupational area.

High-Performance and Simply-Synthesized Ladder-Like Structured Methacrylate Siloxane Hybrid Material for Flexible Hard Coating

Directory of Open Access Journals (Sweden)

Yun Hyeok Kim

2018-04-01

Full Text Available A high performance ladder-like structured methacrylate siloxane hybrid material (LMSH was fabricated via simple hydrolytic sol–gel reaction, followed by free-radical polymerization. A structurally ordered siloxane backbone, the ladder-like structure, which is an essential factor for high performance, could be achieved by a short period of sol–gel reaction in only 4 h. This results in superior optical (Transmittance > 90% at 550 nm, thermal (T5 wt % decomposition > 400 ℃ , mechanical properties(elastic recovery = 0.86, hardness = 0.6 GPa compared to the random- and even commercialized cage-structured silsesquioxane, which also has ordered structure. It was investigated that the fabricated ladder-like structured MSH showed the highest overall density of organic/inorganic co-networks that are originated from highly ordered siloxane network, along with high conversion rate of polymerizable methacrylate groups. Our findings suggest a potential of the ladder-like structured MSH as a powerful alternative for the methacrylate polysilsesquioxane, which can be applied to thermally stable and flexible optical coatings, even with an easier and simpler preparation process.

Synthesis and characterization of nanocomposite polymer blend electrolyte thin films by spin-coating method

Energy Technology Data Exchange (ETDEWEB)

Chapi, Sharanappa; Niranjana, M.; Devendrappa, H., E-mail: dehu2010@gmail.com [Department of Physics, Mangalore University, Mangalagangothri - 574 199 (India)

2016-05-23

Solid Polymer blend electrolytes based on Polyethylene oxide (PEO) and poly vinyl pyrrolidone (PVP) complexed with zinc oxide nanoparticles (ZnO NPs; Synthesized by Co-precipitation method) thin films have prepared at a different weight percent using the spin-coating method. The complexation of the NPs with the polymer blend was confirmed by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR). The variation in film morphology was examined by polarized optical micrographs (POMs). The thermal behavior of blends was investigated under non-isothermal conditions by differential thermal analyses (DTA). A single glass transition temperature for each blend was observed, which supports the existence of compatibility of such system. The obtained results represent that the ternary based thin films are prominent materials for battery and optoelectronic device applications.

Biomimetically-mineralized composite coatings on titanium functionalized with gelatin methacrylate hydrogels

Energy Technology Data Exchange (ETDEWEB)

Tan, Guoxin, E-mail: tanguoxin@126.com [School of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou, 510006 (China); Zhou, Lei [School of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou, 510006 (China); Ning, Chengyun, E-mail: imcyning@scut.edu.cn [College of Materials Science and Technology, South China University of Technology, Guangzhou, 510641 (China); Tan, Ying [School of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou, 510006 (China); Ni, Guoxin [Department of Orthopedics and Traumatology, Nanfang Hospital, Southern Medical University, Guangzhou, 510515 (China); Liao, Jingwen; Yu, Peng; Chen, Xiaofeng [College of Materials Science and Technology, South China University of Technology, Guangzhou, 510641 (China)

2013-08-15

Immobilizing organic–inorganic hybrid composites onto the implant surface is a promising strategy to improve host acceptance of the implant. The objective of this present study was to obtain a unique macroporous titanium-surface with the organic–mineral composite coatings consisting of gelatin methacrylate hydrogel (GelMA) and hydroxyapatite (HA). A 3-(trimethoxysilyl) propyl methacrylate (TMSPMA) layer was first coated onto the titanium surface, and surface was then covalently functionalized with GelMA using a photochemical method. Mineralization of the GelMA coating on the titanium surface was subsequently carried out by a biomimetic method. After 3-day mineralization, a large number of mineral phases comprising spherical amorphous nanoparticles were found randomly deposited inside GelMA matrix. The resulting mineralized hydrogel composites exhibited a unique rough surface of macroporous structure. The structure of the prepared GelMA/HA composite coating was studied by field emission scanning electron microscopy (FESEM), energy dispersive X-ray spectra (EDS), attenuated total refraction Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Water contact angle measurement revealed the hydrophilicity properties of composite coatings. GelMA/HA on titanium after the TMSPMA treatment is very stable when tested in vitro with a PBS solution at 37 °C, due to the role of TMSPMA as a molecular bridge. It was expected that the macroporous GelMA/HA composite coatings might potentially promote and accelerate titanium (Ti)-based implants osseointegration for bone repair and regeneration.

Copolymers of Vinyl-Containing Benzoxazine with Vinyl Monomers as Precursors for High Performance Thermosets

Directory of Open Access Journals (Sweden)

Tsutomu Takeichi

2015-04-01

Full Text Available A benzoxazine containing a vinyl group (P-4va was prepared by the reaction of phenol, 4-vinylaniline, and paraformaldehyde. A differential scanning calorimetry (DSC study revealed that ring-opening polymerization of the benzoxazine and chain polymerization of the vinyl group occurred in the same temperature range. When 2,2'-azobisisobutyronitrile was added as a radical initiator to P-4va, however, only the vinyl groups were polymerized at lower temperature, giving oligo(P-4va that contains pendent benzoxazine units. Radical copolymerization of P-4va with various vinyl monomers such as styrene, methyl methacrylate (MMA, and n-butyl acrylate (BuA was examined. The chemical structure of the copolymers was confirmed by FT-IR and 1H-NMR to be one of polyolefins bearing benzoxazine units as the pendant groups. The weight-average molecular weights of the copolymers determined by size exclusion chromatography were to be in the range of 1900–51,500 depending on the comonomers. DSC of the copolymers showed that the maxima of the exothermic peaks corresponding to the ring-opening polymerization of the pendent benzoxazine units were observed in the temperature range of 229–250 °C. Thermal cure up to 240 °C of the copolymer films afforded homogenous transparent films with improved thermal properties. Tough cured film was obtained by the copolymerization with MMA, while a tough and flexible film was obtained by the copolymerization with BuA.

High temperature oxidation behaviour of nanostructured cermet coatings in a mixed CO2 – O2 environment

International Nuclear Information System (INIS)

Farrokhzad, M A; Khan, T I

2014-01-01

Nanostructured ceramic-metallic (cermet) coatings composed of nanosized ceramic particles (α-Al 2 O3 and TiO 2 ) dispersed in a nickel matrix were co-electrodeposited and then oxidized at 500°C, 600°C and 700°C in a mixed gas using a Thermo-gravimetric Analysis (TGA) apparatus. The mixed gas was composed of 15% CO 2 , 10% O 2 and 75% N 2 . This research investigates the effects of CO 2 and O 2 partial pressures on time-depended oxidation rates for coatings and compared them to the results from atmospheric oxidation under similar temperatures. The increase in partial pressure of oxygen due to the presence of CO 2 at each tested temperature was calculated and correlated to the oxidation rate of the coatings. The results showed that the presence of CO 2 in the system increased the oxidation rate of cermet coatings when compared to atmospheric oxidation at the same temperature. It was also shown that the increase in the oxidation rate is not the result of CO2 acting as the primary oxidant but as a secondary oxidant which results in an increase of the total partial pressure of oxygen and consequently higher oxidation rates. The WDS and XRD analyses results showed that the presence of nanosized TiO 2 particles in a nickel matrix can improve oxidation behaviour of the coatings by formation of Ni-Ti compounds on oxidizing surface of the coating which was found beneficiary in reducing the oxidation rates for cermet coatings

An in-situ infection detection sensor coating for urinary catheters.

Science.gov (United States)

Milo, Scarlet; Thet, Naing Tun; Liu, Dan; Nzakizwanayo, Jonathan; Jones, Brian V; Jenkins, A Toby A

2016-07-15

We describe a novel infection-responsive coating for urinary catheters that provides a clear visual early warning of Proteus mirabilis infection and subsequent blockage. The crystalline biofilms of P. mirabilis can cause serious complications for patients undergoing long-term bladder catheterisation. Healthy urine is around pH 6, bacterial urease increases urine pH leading to the precipitation of calcium and magnesium deposits from the urine, resulting in dense crystalline biofilms on the catheter surface that blocks urine flow. The coating is a dual layered system in which the lower poly(vinyl alcohol) layer contains the self-quenching dye carboxyfluorescein. This is capped by an upper layer of the pH responsive polymer poly(methyl methacrylate-co-methacrylic acid) (Eudragit S100®). Elevation of urinary pH (>pH 7) dissolves the Eudragit layer, releasing the dye to provide a clear visual warning of impending blockage. Evaluation of prototype coatings using a clinically relevant in vitro bladder model system demonstrated that coatings provide up to 12h advanced warning of blockage, and are stable both in the absence of infection, and in the presence of species that do not cause catheter blockage. At the present time, there are no effective methods to control these infections or provide warning of impending catheter blockage. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Polydimethylsiloxane microspheres with poly(methyl methacrylate) coating: Modelling, preparation, and characterization

DEFF Research Database (Denmark)

Ma, Baoguang; Hansen, Jens Henrik; Hvilsted, Søren

2015-01-01

functional PDMS microspheres were coated with poly(methyl methacrylate) (PMMA) by spin coating with different concentrations of PMMA solutions. The quality of the resulting PMMA shell is investigated using rheological measurements at 50 8C with a timesweep procedure. The results strongly suggest that PMMA-coated...... PDMS microspheres react around 20 times slower than the uncoated ones, and that the PMMA shell significantly hinders the reaction between the PDMS microsphere and cross-linker. Thus the thin PMMA shells are very efficient in protecting the reactive PDMS microspheres, since the PMMA shell forms...

Synthesis and characterization of magnetic and non-magnetic core-shell polyepoxide micrometer-sized particles of narrow size distribution.

Science.gov (United States)

Omer-Mizrahi, Melany; Margel, Shlomo

2009-01-15

Core polystyrene microspheres of narrow size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2-methoxy ethanol. Uniform polyglycidyl methacrylate/polystyrene core-shell micrometer-sized particles were prepared by emulsion polymerization at 73 degrees C of glycidyl methacrylate in the presence of the core polystyrene microspheres. Core-shell particles with different properties (size, surface morphology and composition) have been prepared by changing various parameters belonging to the above seeded emulsion polymerization process, e.g., volumes of the monomer glycidyl methacrylate and the crosslinker monomer ethylene glycol dimethacrylate. Magnetic Fe(3)O(4)/polyglycidyl methacrylate/polystyrene micrometer-sized particles were prepared by coating the former core-shell particles with magnetite nanoparticles via a nucleation and growth mechanism. Characterization of the various particles has been accomplished by routine methods such as light microscopy, SEM, FTIR, BET and magnetic measurements.

Characterization and temperature controlling property of TiAlN coatings deposited by reactive magnetron co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Chen, J.T. [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Wang, J. [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); National Key Laboratory of Surface Engineering, Lanzhou Institute of Physics, Lanzhou 730000 (China); Zhang, F.; Zhang, G.A.; Fan, X.Y.; Wu, Z.G. [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Yan, P.X. [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); State Key Laboratory of Solid Lubrication, Lanzhou Institute Chemical and Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: pxyan@lzu.edu.cn

2009-03-20

Titanium aluminum nitride (TiAlN) ternary coating is a potential material which is expected to be applied on satellite for thermal controlling. In order to investigate thermal controlling property, TiAlN coatings were deposited on Si wafers with different N{sub 2} and Ar flux ratio by reactive magnetron co-sputtering. The structure, morphology, chemical composition and optical reflectance are investigated by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), atom force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and spectrophotometer, respectively. The orientation of the coatings depends on the N{sub 2}/Ar flux ratio. The coatings deposited with N{sub 2}/Ar ratio of 10, 30 and 60% show the cubic-TiN [2 2 0] preferred orientation and the coating deposited with N{sub 2}/Ar ratio of 100% exhibits the phase of hexagonal-AlN and cubic-TiN. The surface of the coatings becomes more compact and smoother with the N{sub 2}/Ar ratios increase. XPS spectrum indicates that the oxides (TiO{sub 2} and Al{sub 2}O{sub 3}), oxynitride (TiN{sub x}O{sub y}) and nitrides (TiN and AlN{sub x}) appear at the surface of the coatings. Ignoring internal power, the optimum equilibrium temperature of TiAlN coatings is 18 deg. C and the equilibrium temperature after heat-treated has slight change, which provides the prospective application on thermal controlling.

A Novel Research on Behavior of Zinc Ferrite Nanoparticles in Different Concentration of Poly(vinyl pyrrolidone (PVP

Directory of Open Access Journals (Sweden)

Halimah Mohamed Kamari

2014-04-01

Full Text Available Zinc ferrite nanocrystals were prepared from an aqueous solution containing metal nitrates and various of concentrations of poly(vinyl pyrrolidone (PVP, i.e., 0, 15, 40, and 55 g/L, as a capping agent. To stabilize the particles, they were thermally treated at 873 K, as an optimum calcination temperature. The behaviors of the polymeric precursor were analyzed by use of simultaneous thermo-gravimetry (TG and derivative thermo-gravimetry analyses (DTG. The presence of the crystalline phase in each sample was confirmed by X-ray diffraction (XRD analysis. The average particle size and the morphology of the nanoparticles were determined by transmission electron microscopy (TEM, and these parameters were found to differ at various concentrations of PVP. Fourier transform infrared spectroscopy (FT-IR confirmed the presence of metal oxide bands for all the PVP concentrations and confirmed the absence of organic bands for PVP concentrations less than 55 g/L. Measurements of the magnetization value of the zinc ferrite nanoparticles were obtained at room temperature by using a vibrating sample magnetometer (VSM, which showed that, in the absence of PVP, the sample exhibited a paramagnetic behavior while, in the presence of PVP, samples have a super-paramagnetic behavior.

Fabrication of electrospun HPGL scaffolds via glycidyl methacrylate cross-linker: Morphology, mechanical and biological properties

Energy Technology Data Exchange (ETDEWEB)

Baratéla, Fernando José Costa; Zazuco Higa, Olga [Biotechnology Center, Institute of Energy and Nuclear Research (IPEN), Av. Professor Lineu Prestes 2242, 05508-000 São Paulo, SP (Brazil); Duarte dos Passos, Esdras [PostGraduate Program in Materials for Engineering, Federal University of Itajubá (UNIFEI), Av. BPS 1303, 37500-903 Itajubá, MG (Brazil); Alencar de Queiroz, Alvaro Antonio, E-mail: alencar@unifei.edu.br [Physics and Chemistry Institute (IFQ), Federal University of Itajubá (UNIFEI), Av. BPS 1303, 37500-903 Itajubá, MG (Brazil); High Voltage Laboratory (LAT-EFEI), Federal University of Itajubá (UNIFEI), Av. BPS 1303, 37500-903 Itajubá, MG (Brazil)

2017-04-01

Electrospinning is a suitable method to produce scaffolds composed of nanoscale to microscale fibers, which are comparable to the extracellular matrix (ECM). Hyperbranched polyglycerol (HPGL) is a highly biocompatible polyether polyol potentially useful for the design of fibrous scaffolds mimicking the ECM architecture. However, scaffolds developed from HPGL have poor mechanical properties and morphological stability in the aqueous environments required for tissue engineering applications. This work reports the production of stable electrospun HPGL scaffolds (EHPGLS) using glycidyl methacrylate (GMA) as cross-linker to enhance the water stability and mechanical property of electrospun HPGL. The diameter and morphology of the produced EHPGLS were analyzed by scanning electron microscopy (SEM). It was observed that electrical fields in the range of 0.2 kV·cm{sup −1} to 1.0 kV·cm{sup −1} decrease the average fiber diameter of EHPGLS. The increase in porosity of EHPGLS with GMA concentration indicates the in situ formation of a heterogeneous structure resultant from the phase separation during crosslinking of HPGL by GMA. EHPGLS containing 20% (w/w) GMA concentration possessed highest tensile strength (295.4 ± 11.32 kPa), which is approximately 58 times higher than that of non-crosslinked EHPGLS (5.1 ± 2.12 kPa). The MTS cell viability results showed that the EHPGLS have no significant cytotoxicity effect on Chinese hamster ovary (CHO-K1) cells. Scanning electron microscopy (SEM) indicates that the cultured BALB/3T3 fibroblasts cells were able to keep contact each other's, thus forming a homogeneous monolayer on the internal surface of the EHPGLS. - Highlights: • A hyperbranched polyglycerol (HPGL) scaffold with elastic modulus of 295.4 ± 11.32 kPa was developed for soft tissue repair. • HPGL scaffold was prepared by electrospinning method. • The porosity of HPGL scaffolds can be tuned by selecting the degree of GMA in HPGL. • Electrospun HPGL

Development of a novel anisotropic self-inflating tissue expander: in vivo submucoperiosteal performance in the porcine hard palate.

Science.gov (United States)

Swan, Marc C; Bucknall, David G; Czernuszka, Jan T; Pigott, David W; Goodacre, Timothy E E

2012-01-01

The advent of self-inflating hydrogel tissue expanders heralded a significant advance in the reconstructive potential of this technique. Their use, however, is limited by their uncontrolled isotropic (i.e., uniform in all directions) expansion. Anisotropy (i.e., directional dependence) was achieved by annealing a hydrogel copolymer of poly(methyl methacrylate-co-vinyl pyrrolidone) under a compressive load for a specified time period. The expansion ratio is dictated by the percentage of vinyl pyrrolidone content and the degree of compression. The expansion rate is modified by incorporating the polymer within a silicone membrane. The in vivo efficacy of differing prototype devices was investigated in juvenile pigs under United Kingdom Home Office Licence. The devices were implanted within a submucoperiosteal pocket in a total of six porcine palates; all were euthanized by 6 weeks after implantation. A longitudinal volumetric assessment of the expanded tissue was conducted, in addition to postmortem analysis of the bony and mucoperiosteal palatal elements. Uncoated devices caused excessive soft-tissue expansion that resulted in mucoperiosteal ulceration, thus necessitating animal euthanasia. The silicone-coated devices produced controlled soft-tissue expansion over the 6-week study period. There was a statistically significant increase in the volume of expanded soft tissue with no evidence of a significant acute inflammatory response to the implant, although peri-implant capsule formation was observed. Attenuation of the bony palatal shelf was noted. A unique anisotropic hydrogel device capable of controlled expansion has been developed that addresses a number of the shortcomings of the technology hitherto available.

Surface modification of silk fibroin fibers with poly(methyl methacrylate) and poly(tributylsilyl methacrylate) via RAFT polymerization for marine antifouling applications

Energy Technology Data Exchange (ETDEWEB)

Buga, Mihaela-Ramona [National Research and Development Institute for Cryogenics and Isotopic Technologies, ICIT Rm. Valcea, 240050 Rm. Valcea, Uzinei 4, CP7, Raureni, Valcea (Romania); Zaharia, Cătălin, E-mail: zaharia.catalin@gmail.com [Advanced Polymer Materials Group, University Politehnica of Bucharest, 1-7, Gh. Polizu Street, Sector 1, 011061 Bucharest (Romania); Bălan, Mihai [National Research and Development Institute for Cryogenics and Isotopic Technologies, ICIT Rm. Valcea, 240050 Rm. Valcea, Uzinei 4, CP7, Raureni, Valcea (Romania); Bressy, Christine [Université de Toulon, MAPIEM, EA 4323, 83957 La Garde (France); Ziarelli, Fabio [Fédération des Sciences Chimiques de Marseille, CNRS-FR1739, Spectropole, 13397 Marseille (France); Margaillan, André [Université de Toulon, MAPIEM, EA 4323, 83957 La Garde (France)

2015-06-01

In this study, silk fibroin surface containing hydroxyl and aminogroups was firstly modified using a polymerizable coupling agent 3-(trimethoxysilyl) propyl methacrylate (MPS), in order to induce vinyl groups onto the fiber surface. The reversible addition–fragmentation chain transfer (RAFT)-mediated polymerization of methyl methacrylate (MMA) and tributylsilyl methacrylate (TBSiMA) through the immobilized vinyl bond on the silk fibroin surface in the presence of 2-cyanoprop-2-yl dithiobenzoate (CPDB) as chain-transfer agent and 2,2′-azobis(isobutyronitrile) (AIBN) as initiator was conducted in toluene solution at 70 °C for 24 h. The structure and properties of the modified fiber were characterized by Fourier Transform Infrared Spectroscopy, {sup 13}C, {sup 29}Si Nuclear Magnetic Resonance (NMR) spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), confirming the presence of the coupling molecule and the methacrylate groups onto the silk fibroin fiber surface. Molecular weight distributions were assessed by triple detection size exclusion chromatography (TD-SEC) in order to verify the livingness of the polymerization. - Highlights: • SF surface containing hydroxyl and amino groups was firstly modified with MPS. • RAFT polymerizations of MMA and TBSiMA were studied. • TD-SEC was used to verify the livingness of the RAFT polymerization. • The grafted polymer chains enhance the thermal stability of the SF fibers. • The grafted fibers could be potentially promising candidates as antifouling agents.

Surface modification of silk fibroin fibers with poly(methyl methacrylate) and poly(tributylsilyl methacrylate) via RAFT polymerization for marine antifouling applications

International Nuclear Information System (INIS)

Buga, Mihaela-Ramona; Zaharia, Cătălin; Bălan, Mihai; Bressy, Christine; Ziarelli, Fabio; Margaillan, André

2015-01-01

In this study, silk fibroin surface containing hydroxyl and aminogroups was firstly modified using a polymerizable coupling agent 3-(trimethoxysilyl) propyl methacrylate (MPS), in order to induce vinyl groups onto the fiber surface. The reversible addition–fragmentation chain transfer (RAFT)-mediated polymerization of methyl methacrylate (MMA) and tributylsilyl methacrylate (TBSiMA) through the immobilized vinyl bond on the silk fibroin surface in the presence of 2-cyanoprop-2-yl dithiobenzoate (CPDB) as chain-transfer agent and 2,2′-azobis(isobutyronitrile) (AIBN) as initiator was conducted in toluene solution at 70 °C for 24 h. The structure and properties of the modified fiber were characterized by Fourier Transform Infrared Spectroscopy, 13 C, 29 Si Nuclear Magnetic Resonance (NMR) spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), confirming the presence of the coupling molecule and the methacrylate groups onto the silk fibroin fiber surface. Molecular weight distributions were assessed by triple detection size exclusion chromatography (TD-SEC) in order to verify the livingness of the polymerization. - Highlights: • SF surface containing hydroxyl and amino groups was firstly modified with MPS. • RAFT polymerizations of MMA and TBSiMA were studied. • TD-SEC was used to verify the livingness of the RAFT polymerization. • The grafted polymer chains enhance the thermal stability of the SF fibers. • The grafted fibers could be potentially promising candidates as antifouling agents

High temperature oxidation behaviour of nanostructured cermet coatings in amixed CO/sub 2/ - O/sub 2/ environment

International Nuclear Information System (INIS)

Farrokhzad, M. A.; Khan, T. I.

2013-01-01

Nanostructured ceramic-metallic (cermet) coatings composed of nanosized ceramic particles (alpha-Al /sub 2/O/sub 3/ and TiO/sub 2/) dispersed in a nickel matrix were co-electrodeposited and then oxidized at 500 degree C, 600 degree C and 700 degree C in a mixed gas using a Thermo-gravimetric Analysis (TGA) apparatus. The mixed gas was composed of 15 percentage CO/sub 2/, 10 percentage O/sub 2/ and 75 percentage N/sub 2/. This research investigates the effects of CO/sub 2/ and O/sub 2/ partial pressures on time-depended oxidation rates for coatings and compared them to the results from atmospheric oxidation under similar temperatures. The increase in partial pressure of oxygen due to the presence of CO/sub 2/ at each tested temperature was calculated and correlated to the oxidation rate of the coatings. The results showed that the presence of CO/sub 2/ in the system increased the oxidation rate of cermet coatings when compared to atmospheric oxidation at the same temperature. It was also shown that the increase in the oxidation rate is not the result of CO/sub 2/ acting as the primary oxidant but as a secondary oxidant which results in an increase of the total partial pressure of oxygen and consequently higher oxidation rates. The WDS and XRD analyses results showed that the presence of nanosized TiO/sub 2/ particles in a nickel matrix can improve oxidation behaviour of the coatings by formation of Nu i-Tau i compounds on oxidizing surface of the coating which was found beneficiary in reducing the oxidation rates for cermet coatings. (author)

Radiation-Induced Graft Polymerization of Vinyl Monomers with Anion Groups onto MWNT Supports and Their Application as Electrogenerated Chemiluminescence (ECL Biosensors

Directory of Open Access Journals (Sweden)

Ji-Hye Park

2014-01-01

Full Text Available Vinyl polymer-grafted multiwalled carbon nanotube (MWNT supports with anion groups were prepared for use as biosensor supports by radiation-induced graft polymerization (RIGP of the vinyl monomers acryloyl diphosphoric acid (ADPA, acrylic acid (AA, sodium styrenesulfonate (NaSS, and methacrylic acid (MA onto the surface of MWNTs. The electrogenerated chemiluminescence sensors based on a glass carbon electrode (ECL-GCE and a screen printed electrode (ECL-SPE were fabricated by immobilization of Ru(bpy3 2+ complex after coating of vinyl polymer-grafted MWNT inks on the surface of the GCE and SPE without any polymer binders in order to obtain high electrogenerated chemiluminescence intensity. For detection of alcohol concentration, alcohol dehydrogenase (ADH was immobilized onto an ECL-GCE sensor prepared by poly(NaSS-g-MWNT supports. The prepared biosensor based on ADH is suitable for the detection of ethanol concentration in commercial drinks.

Microstructures and properties of TiN reinforced Co-based composite coatings modified with Y{sub 2}O{sub 3} by laser cladding on Ti–6Al–4V alloy

Energy Technology Data Exchange (ETDEWEB)

Weng, Fei, E-mail: wengfeisdu@126.com [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Department of Materials Science and Engineering, Shandong University, Ji' nan 250061 (China); Shandong University, Suzhou Institute, Suzhou 215123 (China); Yu, Huijun, E-mail: yhj2001@sdu.edu.cn [Key Laboratory of High-efficiency and Clean Mechanical Manufacture (Ministry of Education), School of Mechanical Engineering, Shandong University, Ji' nan 250061 (China); Shandong University, Suzhou Institute, Suzhou 215123 (China); Chen, Chuanzhong, E-mail: czchen@sdu.edu.cn [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Department of Materials Science and Engineering, Shandong University, Ji' nan 250061 (China); Shandong University, Suzhou Institute, Suzhou 215123 (China); Liu, Jianli, E-mail: jianli21s@163.com [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Department of Materials Science and Engineering, Shandong University, Ji' nan 250061 (China); Shandong University, Suzhou Institute, Suzhou 215123 (China); Zhao, Longjie, E-mail: zhaoljsdu@sina.com [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Department of Materials Science and Engineering, Shandong University, Ji' nan 250061 (China); Shandong University, Suzhou Institute, Suzhou 215123 (China)

2015-11-25

In this study, TiN reinforced composite coatings were fabricated on Ti–6Al–4V substrate by laser cladding with Co42 self-fluxing alloy, TiN and Y{sub 2}O{sub 3} mixed powders. Microstructures and wear resistance of the cladding coatings with and without Y{sub 2}O{sub 3} addition were investigated comparatively. Results showed that the coatings were mainly comprised of γ-Co/Ni, TiN, CoTi, CoTi{sub 2}, NiTi, TiC, Cr{sub 7}C{sub 3}, TiB, Ti{sub 5}Si{sub 3} and TiC{sub 0.3}N{sub 0.7} phases. The coatings showed metallurgical bonding free of pores and cracks with the substrate. Compared with the Ti–6Al–4V substrate, the microhardness and wear resistance of the coatings was enhanced by 3–4 times and 9.5–11.9 times, respectively. With 1.0 wt.% Y{sub 2}O{sub 3} addition, the microstructure of the coating was refined significantly, and the microhardness and dry sliding wear resistance were enhanced further. The effects of Y{sub 2}O{sub 3} were attributed to the residual Y{sub 2}O{sub 3} and decomposed Y atoms. - Graphical abstract: The diagram illustration for the action mechanism of Y{sub 2}O{sub 3}: (a) dissolution of Y{sub 2}O{sub 3} and TiN, (b) re-formation of TiN and in situ formation of TiC, (c) growth of TiN, TiC and the distribution of Y atoms. - Highlights: • Coatings showing metallurgical bonding with the substrate were fabricated. • The effect of Y{sub 2}O{sub 3} on the refinement of the microstructure is notable. • A kind of Y{sub 2}O{sub 3} centered core–shell structure was picked out in the coating. • Microhardness and wear resistance of the coatings was enhanced significantly.

Influence of Methacrylic-Acrylic Copolymer Composition on Plasticiser-free Optode Films for pH Sensors

Directory of Open Access Journals (Sweden)

Musa Ahmad

2003-03-01

Full Text Available In this work we have examined the use of plasticiser-free polymeric films incorporating a proton selective chromoionophore for optical pH sensor. Four types of methacrylic-acrylic copolymers containing different compositions of n-butyl acrylate (nBA and methyl methacrylate (MMA were synthesised for use as optical sensor films. The copolymers were mixed with appropriate amounts of chromoionophore (ETH5294 and a lipophilic salt before spin coated on glass slides to form films for the evaluation of pH response using spectrophotometry. Co-polymer films with high nBA content gave good response and the response time depended on the film thickness. A preliminary evaluation of the optical films of high nBA content with pHs from 2 - 14 showed distinguishable responses from pH 5 - 9. However, the adhesion of the pH sensitive film was good for copolymers with higher content of MMA but not for films with high nBA.

VO2 /TiN Plasmonic Thermochromic Smart Coatings for Room-Temperature Applications.

Science.gov (United States)

Hao, Qi; Li, Wan; Xu, Huiyan; Wang, Jiawei; Yin, Yin; Wang, Huaiyu; Ma, Libo; Ma, Fei; Jiang, Xuchuan; Schmidt, Oliver G; Chu, Paul K

2018-03-01

Vanadium dioxide/titanium nitride (VO 2 /TiN) smart coatings are prepared by hybridizing thermochromic VO 2 with plasmonic TiN nanoparticles. The VO 2 /TiN coatings can control infrared (IR) radiation dynamically in accordance with the ambient temperature and illumination intensity. It blocks IR light under strong illumination at 28 °C but is IR transparent under weak irradiation conditions or at a low temperature of 20 °C. The VO 2 /TiN coatings exhibit a good integral visible transmittance of up to 51% and excellent IR switching efficiency of 48% at 2000 nm. These unique advantages make VO 2 /TiN promising as smart energy-saving windows. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Biocatalytic Asymmetric Synthesis of (1R, 2S)-N-Boc-vinyl-ACCA Ethyl Ester with a Newly Isolated Sphingomonas aquatilis.

Science.gov (United States)

Zhu, Shaozhou; Shi, Ying; Zhang, Xinyu; Zheng, Guojun

2018-02-01

1-amino cyclopropane-1-carboxylic acid (ACCA) and its derivatives are essential pharmacophoric unit that widely used in drug research and development. Specifically, (1R, 2S)-N-Boc-vinyl-ACCA ethyl ester (vinyl-ACCA) is a key chiral intermediate in the synthesis of highly potent hepatitis C virus (HCV) NS3/4A protease inhibitors such as asunaprevir and simeprevir. Developing strategies for the asymmetric synthesis of vinyl-ACCA is thus extremely high demand. In this study, 378 bacterial strains were isolated from soil samples using N-Boc-vinyl-ACCA ethyl ester as the sole carbon source and were screened for esterase activity. Fourteen of which worked effectively for the asymmetric synthesis of (1R, 2S)-N-Boc-1-vinyl ACCA ethyl ester. The strain CY-2, identified as Sphingomonas aquatilis, which showed the highest stability and enantioselectivity was selected as whole cell biocatalyst for further study. A systematic study of all factors influencing the enzymatic hydrolysis was performed. Under optimized conditions, resolution of rac-vinyl-ACCA to (1R, 2S)-N-Boc-1-vinyl ACCA ethyl ester with 88.2% ee and 62.4% conversion (E = 9) was achieved. Besides, S. aquatilis was also used to transform other 10 different substrates. Notably, it was found that 7 of them could be stereoselectively hydrolyzed, especially for (1R,2S)-1-amino-vinyl-ACCA ethyl ester hydrochloride (99.6% ee, E>200). Our investigations provide a new efficient whole cell biocatalyst for resolution of ACCA and might be developed for industry application.

Wear Performance of Sequentially Cross-Linked Polyethylene Inserts against Ion-Treated CoCr, TiNbN-Coated CoCr and Al2O3 Ceramic Femoral Heads for Total Hip Replacement

Directory of Open Access Journals (Sweden)

Christian Fabry

2015-02-01

Full Text Available The aim of the present study was to evaluate the biotribology of current surface modifications on femoral heads in terms of wettability, polyethylene wear and ion-release behavior. Three 36 mm diameter ion-treated CoCr heads and three 36 mm diameter TiNbN-coated CoCr heads were articulated against sequentially cross-linked polyethylene inserts (X3 in a hip joint simulator, according to ISO 14242. Within the scope of the study, the cobalt ion release in the lubricant, as well as contact angles at the bearing surfaces, were investigated and compared to 36 mm alumina ceramic femoral heads over a period of 5 million cycles. The mean volumetric wear rates were 2.15 ± 0.18 mm3·million cycles−1 in articulation against the ion-treated CoCr head, 2.66 ± 0.40 mm3·million cycles−1 for the coupling with the TiNbN-coated heads and 2.17 ± 0.40 mm3·million cycles−1 for the ceramic heads. The TiNbN-coated femoral heads showed a better wettability and a lower ion level in comparison to the ion-treated CoCr heads. Consequently, the low volumes of wear debris, which is comparable to ceramics, and the low concentration of metal ions in the lubrication justifies the use of coated femoral heads.

Rheological, mechanical and morphological properties of poly(methyl methacrylate/poly(ethylene terephthalate blend with dual reactive interfacial compatibilization

Directory of Open Access Journals (Sweden)

Juciklécia da Silva Reinaldo

2015-10-01

Full Text Available Abstract In this work, the rheological, mechanical and morphological behavior of immiscible blend poly (methyl methacrylate with elastomeric particles (PMMAelast and post-consumer poly (ethylene terephthalate (PET with and without the use of the interfacial compatibilizer poly (methyl methacrylate-co-glycidyl methacrylate-co-ethyl acrylate (MGE was studied. The significant increase in torque presented in rheological analyses has shown a indication of chemical reactions between the epoxy group of MGE with end groups of PET chains and also with the elastomeric phase of PMMAelast. The increased concentration of PET yielded an increase in maximum strength and elasticity modulus and a decrease in elongation at break. The PMMAelast/PET binary blend (50/50 wt% and PMMAelast/PET/MGE compatibilized blend (65/30/5 wt% showed pronounced results in elongation at break compared to PMMAelast, whereas, in the first results were due to the evidence of a co-continuous morphological structure and in the second, due to the efficiency of the dual reactive interfacial compatibilization of PMMAelast/PET blends. Scanning electron microscopy (SEM and transmission electron microscopy (TEM analyses showed that PMMAelast/PET/MGE blends exhibit complex phase morphology due to the presence of elastomeric particles in the PMMAelast copolymer and in the use of MGE terpolymer.

High performance oligomers: synthesis and photochemical properties of calix(n)arene containing various photoreactive groups

International Nuclear Information System (INIS)

Nishikubo, T.; Kameyama, A.

1999-01-01

Photoreactive calix(n)arenes containing radical polymerizable (meth)acrylate groups, and catatonically polymerizable vinyl ether, propargyl ether, oxirane and oxetane groups were synthesized by certain reactions of calix(n)arenes with the corresponding (meth)acrylic acid derivatives, vinyl ether compound, epibromohydrin and oxetane derivatives, respectively. The photochemical reaction of these calix(n)arene derivatives were also examined

Experimental evaluation of coating delamination in vinyl coated metal forming

International Nuclear Information System (INIS)

Son, Young Ki; Lee, Chan Joo; Kim, Byung Min; Lee, Jung Min; Byoen, Sang Doek; Lee, Soen Bong

2012-01-01

In this paper, a new evaluation and prediction method for coating delamination during sheet metal forming is presented. On the basis of the forming limit diagram (FLD), the current study evaluates the delamination of PET coating by using a cross cut specimen, dome test, and rectangular cup drawing test. Dome test specimens were subjected to biaxial, plane strain, and uniaxial deformation modes. Rectangular cup drawing test specimens were subjected to the deep drawing deformation mode, and compression deformation mode. A vinyl coated metal (VCM) sheet consists of three layers of polymer on the sheet metals: a protective film, a PET layer and a PVC layer. The areas with coating delamination were identified, and the results of the evaluation were plotted according to major and minor strain values, depicting coating delamination. The constructed delamination limit diagram (DLD) can be used to determine the forming limit of VCM during the complex press forming process. ARGUS (GOM) was employed to identify the strain value and deformation mode of the delaminated surface after the press forming. After identifying the areas of delamination, the DLD of the PET coating can be constructed in a format similar to that of the FLD. The forming limit of the VCM sheet can be evaluated using the superimposition of the delamination limit strain of the coating onto the FLD of VCM sheet. The experimental results showed that the proposed test method will support the sheet metal forming process design for VCM sheets. The assessment method presented in this study can be used to determine the delamination limit strain under plastic deformation of other polymer coated metals. The experimental results suggested that the proposed testing method is effective in evaluating delamination for specific applications

Experimental evaluation of coating delamination in vinyl coated metal forming

Energy Technology Data Exchange (ETDEWEB)

Son, Young Ki; Lee, Chan Joo; Kim, Byung Min [Pusan National Univ., Busan (Korea, Republic of); Lee, Jung Min [Korea Institute of Industrial Technology, Busan (Korea, Republic of); Byoen, Sang Doek [HA Digital Engineering Gr., Seongsan Gu (Korea, Republic of); Lee, Soen Bong [Keimyung Univ., Daegu (Korea, Republic of)

2012-10-15

In this paper, a new evaluation and prediction method for coating delamination during sheet metal forming is presented. On the basis of the forming limit diagram (FLD), the current study evaluates the delamination of PET coating by using a cross cut specimen, dome test, and rectangular cup drawing test. Dome test specimens were subjected to biaxial, plane strain, and uniaxial deformation modes. Rectangular cup drawing test specimens were subjected to the deep drawing deformation mode, and compression deformation mode. A vinyl coated metal (VCM) sheet consists of three layers of polymer on the sheet metals: a protective film, a PET layer and a PVC layer. The areas with coating delamination were identified, and the results of the evaluation were plotted according to major and minor strain values, depicting coating delamination. The constructed delamination limit diagram (DLD) can be used to determine the forming limit of VCM during the complex press forming process. ARGUS (GOM) was employed to identify the strain value and deformation mode of the delaminated surface after the press forming. After identifying the areas of delamination, the DLD of the PET coating can be constructed in a format similar to that of the FLD. The forming limit of the VCM sheet can be evaluated using the superimposition of the delamination limit strain of the coating onto the FLD of VCM sheet. The experimental results showed that the proposed test method will support the sheet metal forming process design for VCM sheets. The assessment method presented in this study can be used to determine the delamination limit strain under plastic deformation of other polymer coated metals. The experimental results suggested that the proposed testing method is effective in evaluating delamination for specific applications.

Effect of 60Co γ-rays on polyphenyl methacrylate obtained by γ-ray irradiation

International Nuclear Information System (INIS)

Raghunath, S.; Rao, M.H.; Rao, K.N.

1983-01-01

Polyphenyl methacrylate of different molecular weights Msub(n) 13000, 34500 and crosslinked polymer prepared by 60 Co γ-irradiation has been irradiated with 60 Co γ-rays at 300 K. G(scission) of the 13000 molecular weight polymer was 15. The crosslinked polymer undergoes both degradation and crosslinking. G(x) value determined for that polymer is approx. 9. The gaseous product consists largely of CO with some CO 2 and H 2 . Hydrocarbon gases were not detected. The yield of H 2 is only to the extent of 2 to 5% of the total gas and it is assumed that majority of scission takes place at the ester linkage. On the basis of the estimation of phenol and benzene, a mechanism for degradation and crosslinking is proposed. (author)

Radiation-induced cationic curing of vinyl ethers

International Nuclear Information System (INIS)

Lapin, S.C.

1992-01-01

Recently there has been an increasing interest in nonacrylate radiation-curable coatings. Vinyl ethers are particularly reactive under cationic polymerization reaction conditions. The high efficiency of the photoacid initiators combined with the high reactivity of vinyl ether monomers makes this a potentially very useful system. This chapter discusses the preparation of vinyl ethers, introduces vinyl ether-functional monomers and oligomers, describes radiation-induced cationic polymerization of vinyl ethers, and discusses various coating systems. Throughout the chapter, an emphasis is placed on radiation-curable coating applications. 64 refs., 5 figs., 11 tabs

Influence of Glycidyl Methacrylate Grafting on the Mechanical, Water Absorption, and Thermal Properties of Recycled High-Density Polyethylene/Rubber Seed Shell Particle Composites

Directory of Open Access Journals (Sweden)

Kaimeng Xu

2016-01-01

Full Text Available Rubber seed shell (RSS was modified by grafting treatment using glycidyl methacrylate (GMA at various concentrations. The RSS was then used to reinforce high-density polyethylene (HDPE. The effects of modification on the mechanical, water absorption, and thermal properties of the RSS/HDPE composites were studied using a mechanical testing instrument, weighing method, Vicat softening temperature (VST testing, thermogravimetry, and dynamic mechanical analysis. The results showed that the GMA grafting produced an improvement in the flexural and tensile properties of the composites. The water absorption rate of the composites also had an obvious decrease. While a slight increase in VST was found, the various concentrations of GMA showed no improvement in VST. GMA modification also could elevate the thermal stability of the composites at the initial decomposition stage. The optimum grafting concentration of GMA (2.5% led to the lowest thermal weight loss (37.07% and 26.56% during the first and second decomposition stages. The E’ values of the composites had a significant increase with the addition of GMA. There were two peaks of tan δ for the untreated samples, but the modified samples exhibited a shift in the transition peak at higher temperatures; moreover, the second peak disappeared.

Effects of pore forming agents on chitosan-graft-poly(N-vinylpyrrolidone) hydrogel properties for use as a matrix for floating drug delivery

Science.gov (United States)

Budianto, E.; Al-Shidqi, M. F.; Cahyana, A. H.

2017-07-01

Eradicating H. pylori-based infection by using conventional oral dosage form of amoxicillin trihydrate finds difficulties to overcome rapid gastric retention time. Encapsulating amoxicillin trihydrate in floating drug delivery system may solve the problem. In this research, the floating drug delivery system of amoxicillin trihydrate encapsulated in floating chitosan-graft-poly(N-vinyl pyrrolidone) hydrogels containing CaCO3 and NaHCO3 as pore forming agents has been successfully prepared. Pore forming agents used was varied with the ratio of 10 to 25% pore forming agents to total mass of the used materials. The hydrogel were characterizedusing FTIR spectrophotometer and stereo microscope. As pore forming agents compositions increased, the porosity (%) and floating properties increased but followed by decrease in drug entrapment efficiency. Most of the floating hydrogels possessed floating ability longer than 180 min and the highest porosity was found in hydrogel containing 25% NaHCO3. Hydrogel containing CaCO3 showed sustained drug release profile than hydrogel containing NaHCO3. However, the optimum formulation was achieved at composition of 10% NaHCO3 with 57% of drug entrapped within the hydrogel and 43% drug released. The results of these studies show that NaHCO3 is an effective pore forming agents for chitosan-graft-poly(N-vinyl pyrrolidone) hydrogel preparation as compare to CaCO3.

Self-assembled hemocompatible coating on poly (vinyl chloride) surface

Energy Technology Data Exchange (ETDEWEB)

Zha Zhengbao; Ma Yan; Yue Xiuli; Liu Meng [Nanobiotechnology Division, State Key Laboratory of Urban Water Resources and Environment, School of Sciences, Harbin Institute of Technology, Harbin 150001 (China); Dai Zhifei, E-mail: zhifei.dai@hit.edu.cn [Nanobiotechnology Division, State Key Laboratory of Urban Water Resources and Environment, School of Sciences, Harbin Institute of Technology, Harbin 150001 (China)

2009-11-15

A stable hemocompatible coating was fabricated by consecutive alternating adsorption of iron (III) and two kinds of polysaccharides, heparin (Hep) and dextran sulfate (DS), onto poly (vinyl chloride) (PVC) surfaces via electrostatic interaction. The fluctuation of contact angles with the alternative deposition of iron (III) and polysaccharides verified the progressive buildup of the mulitilayer coating onto the PVC surface. Atomic force microscopy (AFM) analysis revealed that the PVC surfaces were completely masked by iron-polysaccharides multilayer coatings. The activated partial thromboplastin time (APTT) assay showed that both Hep/Fe{sup 3+}/Hep and DS/Fe{sup 3+}/Hep coated PVC were less thrombogenic than the uncoated one. Chromogenic assay for heparin activity proved definitively that the inhibition of locally produced thrombin was ascribed to the thromboresistance of the surface-bound heparin. Compared with the unmodified PVC surfaces, iron-polysaccharide multilayer coating presented a drastically reduced adhesion in vitro of platelets, polymorphonuclear neutrophil leukocytes (PMN) and peripheral blood mononuclear cells (PBMC). Interestingly, the DS/Fe{sup 3+}/Hep coating was found to exhibit higher hydrophilicity and stability, hence lower non-specific protein adsorption in comparison with Hep/Fe{sup 3+}/Hep coating due to the incorporation of dextran sulfate into the multilayer coating.

High cyclability of carbon-coated TiO2 nanoparticles as anode for sodium-ion batteries

International Nuclear Information System (INIS)

Ge, Yeqian; Jiang, Han; Zhu, Jiadeng; Lu, Yao; Chen, Chen; Hu, Yi; Qiu, Yiping; Zhang, Xiangwu

2015-01-01

Highlights: • Titanium oxide nanopaticles were modified by carbon coating from pyrolyzing of PVP. • Carbon coating gave rise to excellent cycling ability of TiO 2 for sodium-ion batteries. • The reversible capacity of carbon-coated TiO 2 reached 242.3 mAh g −1 at 30 mA g −1 . • Good rate performance of carbon-coated TiO 2 was presented up to 800 mA g −1 . - Abstract: Owing to the merits of good chemical stability, elemental abundance and nontoxicity, titanium dioxide (TiO 2 ) has drawn increasing attraction for use as anode material in sodium-ion batteries. Nanostructured TiO 2 was able to achieve high energy density. However, nanosized TiO 2 is typically electrochemical instable, which leads to poor cycling performance. In order to improve the cycling stability, carbon from thermolysis of poly(vinyl pyrrolidone) was coated onto TiO 2 nanoparticles. Electronic conductivity and electrochemical stability were enhanced by coating carbon onto TiO 2 nanoparticles. The resultant carbon-coated TiO 2 nanoparticles exhibited high reversible capacity (242.3 mAh g −1 ), high coulombic efficiency (97.8%), and good capacity retention (87.0%) at 30 mA g −1 over 100 cycles. By comparison, untreated TiO 2 nanoparticles showed comparable reversible capacity (237.3 mAh g −1 ) and coulombic efficiency (96.2%), but poor capacity retention (53.2%) under the same condition. The rate performance of carbon-coated TiO 2 nanoparticles was also displayed as high as 127.6 mAh g −1 at a current density of 800 mA g −1 . The improved cycling performance and rate capability were mostly attributed to protective carbon layer helping stablize solid electrolyte interface formation of TiO 2 nanoparticles and improving the electronic conductivity. Therefore, it is demonstrated that carbon-coated TiO 2 nanoparticles are promising anode candidate for sodium-ion batteries

Coating material composition

International Nuclear Information System (INIS)

Kimura, Tadashi; Ozeki, Takao; Kobayashi, Juichi; Nakamoto, Hideo; Maeda, Yutaka.

1969-01-01

A coating material composition is provided which can easily be cross-linked by irradiation with active energy, particularly electron beams and ultraviolet light, using a mixture of a prepolymer (a) with an addition reaction product (b). Such compositions have coating properties as good as thermosetting acrylic or amino alkyd resins. The prepolymer (a) is produced by primarily reacting at least 0.1 mol of saturated cyclocarboxylic acid anhydrides and/or alpha-, beta-ethylene unsaturated carboxylic acid anhydrides by addition reaction with one mol of hydroxyl radicals of a basic polymer having a molecular weight of 1,000 to 100,000, the basic polymer being obtained from 1%-40% of a hydroxyl radical containing vinyl monomer and at least 30% of (meth)acrylate monomer. One mol of the sum of hydroxyl radicals and carboxyl radicals of the primary reaction product undergoes a secondary addition reaction with at least 0.1 mol of an epoxy radical-containing vinyl monomer to form the prepolymer(a). The addition reaction product(b) is produced by reacting an epoxy radical-containing vinyl monomer with alpha-, beta-ethylene unsaturated carboxylic acids or their anhydrides. The coating material composition contains a majority of a mixture consisting of 10%-90% of (a) and 90%-10% of (b) above by weight. Four examples of the production of basic polymers, seven examples of the production of prepolymers, seven examples of the production of oligomers, and five examples of applications are given. (Iwakiri, K.)

Studies on Development of Polymeric Materials Using Gamma Irradiation for Contact and Intraocular Lenses

Directory of Open Access Journals (Sweden)

Pranshu Chhabra

2009-01-01

Full Text Available For the development of materials for contact lenses and intraocular lenses, the selection criteria is based on the (i capacity to absorb and retain water, (ii hydrophilicity and hydrophobicity, (iii refractive index and (iv hardness besides the other essential properties. Various monomers are being studied to develop suitable materials for such applications. Selection of suitable monomers that can be converted into optical materials of desired characteristics is the most essential step. In the present paper, an attempt has been made to develop suitable optical polymers based on 2-hydroxy ethyl methacrylate (HEMA, N-vinyl pyrrolidone (NVP, methyl methacrylate (MMA, methacrylic acid (MAA, and styrene. Compositions were prepared in such a way that polymers of varying hydrophilicity or hydrophobicity could be obtained keeping HEMA as the base (main monomer. For polymerization, gamma irradiation (Co-60 as a source was used. The results of the study showed that: (i an increase in NVP and MAA content brought in an increase in hydrophilicity of polymerized HEMA (pHEMA, while the addition of styrene and MMA decreased hydrophilicity of polymerized HEMA (pHEMA, (ii polymers for contact lenses with water retention capacity as high as >50 wt.% and as low as <10 wt% with varying content of suitable comonomers can be designed, (iii polymeric materials for contact lenses can be made by using radiation processing such as Co-60 and (iv a dose of 40 kGy was found to be ideal for purpose.

Poly(vinyl chloride)-g-poly(2-(dimethylamino)ethyl methacrylate) graft copolymers templated synthesis of mesoporous TiO{sub 2} thin films for dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Patel, Rajkumar; Ahn, Sung Hoon; Seo, Jin Ah; Kim, Sang Jin; Kim, Jong Hak, E-mail: jonghak@yonsei.ac.kr [Yonsei University, Department of Chemical and Biomolecular Engineering (Korea, Republic of)

2012-07-15

A poly(vinyl chloride) (PVC) main chain was grafted with poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) containing a quaternary amine group using atom transfer radical polymerization. The successful synthesis of a PVC-g-PDMAEMA graft copolymer was confirmed by Fourier transform infrared, nuclear magnetic resonance, thermogravimetric analysis, and transmission electron microscopy. The PVC-g-PDMAEMA graft copolymer was used as a structure-directing agent (SDA) for the fabrication of a mesoporous thin film containing a titanium dioxide (TiO{sub 2}) layer. To control the porosity of the resultant inorganic layer, the ratio of SDA to TTIP as well as the concentration of the sol-gel was varied. The structure and porosity of the mesoporous film were characterized by XRD and SEM analysis. The mesoporous TiO{sub 2} film fabricated on the FTO surface was used as a photoanode for the dye-sensitized solar cell (DSSC). DSSC performance was the greatest when using TiO{sub 2} film with a higher porosity and lower interfacial resistance. The highest energy conversion efficiency reached 3.2 % at 100 mW/cm{sup 2}, which was one of the highest reported values for a quasi-solid-state DSSC with 600-nm-thick TiO{sub 2} film.

Effect of gamma ray on poly(lactic acid)/poly(vinyl acetate-co-vinyl alcohol) blends as biodegradable food packaging films

International Nuclear Information System (INIS)

Razavi, Seyed Mohammad; Dadbin, Susan; Frounchi, Masoud

2014-01-01

Poly(lactic acid) (PLA)/poly(vinyl acetate-co-vinyl alcohol) [P(VAc-co-VA)] blends as new transparent film packaging materials were prepared at various blend compositions and different vinyl alcohol contents. The blends and pure PLA were irradiated by gamma rays to investigate the extent of changes in the packaging material during gamma ray sterilization process. The miscibility of the blends was dependent on the blend composition and vinyl alcohol content; gamma irradiation had little effect on the extent of miscibility. The glass transition temperature of pure PLA and PLA/P(VAc-co-VA) miscible blends reduced after irradiation. On the other hand in PLA/P(VAc-co-VA) immiscible blends, while the glass transition temperature of the PLA phase decreased; that of the copolymer phase slightly increased. The reduction in the glass transition was about 10 percent for samples irradiated with 50 kGy indicating dominance of chain scission of PLA molecules at high irradiation dose. The latter was verified by drop in mechanical properties of pure PLA after exposing to gamma irradiation at 50 kGy. Blending of PLA with the copolymer P(VAc-co-VA) compensated greatly the adverse effects of irradiation on PLA. The oxygen-barrier property of the blend was superior to the neat PLA and remained almost intact with irradiation. The un-irradiated and irradiated blends had excellent transparency. Gamma ray doses used for sterilization purposes are usually less than 20 kGy. It was shown that gamma irradiation at 20 kGy had no or little adverse effects on PLA/P(VAc-co-VA) blends mechanical and gas barrier properties. - Highlights: • Poly(lactic acid)/poly(vinyl acetate-co-vinyl alcohol) blends were prepared as new packaging film. • The blends are superior to PLA in oxygen gas barrier property. • The blends are suitable for gamma ray sterilization and maintain useful mechanical properties. • The blends are perfectly transparent

A One-Step Route to CO2 -Based Block Copolymers by Simultaneous ROCOP of CO2 /Epoxides and RAFT Polymerization of Vinyl Monomers.

Science.gov (United States)

Wang, Yong; Zhao, Yajun; Ye, Yunsheng; Peng, Haiyan; Zhou, Xingping; Xie, Xiaolin; Wang, Xianhong; Wang, Fosong

2018-03-26

The one-step synthesis of well-defined CO 2 -based diblock copolymers was achieved by simultaneous ring-opening copolymerization (ROCOP) of CO 2 /epoxides and RAFT polymerization of vinyl monomers using a trithiocarbonate compound bearing a carboxylic group (TTC-COOH) as the bifunctional chain transfer agent (CTA). The double chain-transfer effect allows for independent and precise control over the molecular weight of the two blocks and ensures narrow polydispersities of the resultant block copolymers (1.09-1.14). Notably, an unusual axial group exchange reaction between the aluminum porphyrin catalyst and TTC-COOH impedes the formation of homopolycarbonates. By taking advantage of the RAFT technique, it is able to meet the stringent demand for functionality control to well expand the application scopes of CO 2 -based polycarbonates. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

High efficiency dry coating of non-subcoated pellets for sustained drug release formulations using amino methacrylate copolymers.

Science.gov (United States)

Klar, Fabian; Urbanetz, Nora Anne

2017-12-12

Dry coating utilizing a fluidized bed was evaluated in order to produce films with sustained drug release using amino methacrylate copolymers as film former. In contrast to other dry coating procedures using amino methacrylate copolymers, the described method enables an appropriate polymer adhesion by the selection of a plasticizer additive mixture in combination with the use of a three-way nozzle for simultaneous application. Well spreading fatty acid esters were found to increase the coating efficiency from 73% to approximately 86%, when they were used in conjunction with the plasticizer. Pellets were used as drug cores without previous treatment. After a curing step at 55 °C, the pellets exhibited a prolongation of the drug release over a period of about 6 h. Mainly the three parameters, coating level, composition of the polymers in the coating mixture, and the type of plasticizer, were found to exert distinct influence on the dissolution profile. Despite the differences in the coating procedure, the dissolution profiles of the coated pellets as well as the influencing parameters were similar to those known from conventional coating techniques.

Effect of drug loading method against the dissolution mechanism of encapsulated amoxicillin trihidrate drug in matrix of semi-IPN chitosan-poly (N-vinyl pyrrolidone) hydrogel with pore forming agent CaCO3

Science.gov (United States)

Nurjannah, Yanah; Budianto, Emil

2018-04-01

Heliobacter pylori (H.pylori) is a type of bacteria that causes inflammation in the lining of the stomach. The treatment of the bacterial infection by using conventional medicine which is amoxicillin trihidrate has a very short retention time in the stomach which is about 1-1,5 hours. Floating drug delivery system is expected to have a long retention time in the stomach so the efficiency of drug can be achieved. In this study, has been synthesized matrix of semi-IPN chitosan-Poly(N-vinil pyrrolidone) hydrogel with a pore-forming agent of CaCO3 under optimum conditions. Amoxicillin is encapsulated in a matrix hydrogel to be applied as a floating drug delivery system by in situ loading and post loading methods. The encapsulation efficiency and dissolution of in situ loading and post loading hydrogels are performed in vitro on gastric pH. In situ loading hydrogel shows higer percentage of encapsulation efficiency and dissolution compared to post loading hydrogel. The encapsulation efficiency of in situ and post loading hydrogels were 92,1% and 89,4%, respectively. The aim of drug dissolution by mathematical equation model is to know kinetics and the mecanism of dissolution. The kinetics release of in situ hydrogel tends to follow first order kinetics, while the post loading hydrogel follow the Higuchi model. The dissolution mecanism of hydrogels is erosion.

Effect of /sup 60/Co. gamma. -rays on polyphenyl methacrylate obtained by. gamma. -ray irradiation

Energy Technology Data Exchange (ETDEWEB)

Raghunath, S.; Rao, M.H.; Rao, K.N. (Bhabha Atomic Research Centre, Bombay (India). Chemistry Div.)

1983-01-01

Polyphenyl methacrylate of different molecular weights Msub(n) 13000, 34500 and crosslinked polymer prepared by /sup 60/Co ..gamma..-irradiation has been irradiated with /sup 60/Co ..gamma..-rays at 300 K. G(scission) of the 13000 molecular weight polymer was 15. The crosslinked polymer undergoes both degradation and crosslinking. G(x) value determined for that polymer is approx. 9. The gaseous product consists largely of CO with some CO/sub 2/ and H/sub 2/. Hydrocarbon gases were not detected. The yield of H/sub 2/ is only to the extent of 2 to 5% of the total gas and it is assumed that majority of scission takes place at the ester linkage. On the basis of the estimation of phenol and benzene, a mechanism for degradation and crosslinking is proposed.

Viscometric investigation of compatibilization of the poly(vinyl chloride)/poly(ethylene-co-vinyl acetate) blends by terpolymer of maleic anhydride styrene vinyl acetate

Science.gov (United States)

İmren, Dilek; Boztuğ, Ali; Yılmaz, Ersen; Zengin, H. Bayram

2008-11-01

In this study, a blend of poly(vinyl chloride) (PVC)/ethylene-co-vinyl acetate (EVA) was compatibilized by terpolymer of maleic anhydride-styrene-vinyl acetate (MAStVA) used as a compatibilizer. It was prepared the blends of 50/50 PVC/EVA containing 2-10% of the terpolymer. The compatibility experiences of these blends were investigated by using viscometric method in the range of concentrations (0.5-2.0 g dL -1) where tetrahydrofuran (THF) is the solvent. The interaction parameter (Δ b) was used to study the miscibility and compatibility of polymer blend in solution, obtained from the modified Krigbaum and Wall theory. Turbidity and FTIR measurements were also used to investigate the miscibility of this pair of polymers. The values of the relative viscosities of the each polymer solution and their blends were measured by a Cannon-Fenske type viscometer. In consequence of the study, it was observed that a considerable improvement was achieved in the miscibility of PVC/EVA blends by adding among 5 and 10 wt% of compatibilizer.

Solid Phase Extraction of Trace Al(III), Fe(II), Co(II), Cu(II), Cd(II) and Pb(II) Ions in Beverages on Functionalized Polymer Microspheres Prior to Flame Atomic Absorption Spectrometric Determinations.

Science.gov (United States)

Berber, Hale; Alpdogan, Güzin

2017-01-01

In this study, poly(glycidyl methacrylate-methyl methacrylate-divinylbenzene) was synthesized in the form of microspheres, and then functionalized by 2-aminobenzothiazole ligand. The sorption properties of these functionalized microspheres were investigated for separation, preconcentration and determination of Al(III), Fe(II), Co(II), Cu(II), Cd(II) and Pb(II) ions using flame atomic absorption spectrometry. The optimum pH values for quantitative sorption were 2 - 4, 5 - 8, 6 - 8, 4 - 6, 2 - 6 and 2 - 3 for Al(III), Fe(II), Co(II), Cu(II), Cd(II) and Pb(II), respectively, and also the highest sorption capacity of the functionalized microspheres was found to be for Cu(II) with the value of 1.87 mmol g -1 . The detection limits (3σ; N = 6) obtained for the studied metals in the optimal conditions were observed in the range of 0.26 - 2.20 μg L -1 . The proposed method was successfully applied to different beverage samples for the determination of Al(III), Fe(II), Co(II), Cu(II), Cd(II) and Pb(II) ions, with the relative standard deviation of <3.7%.

Preparation of high-capacity, weak anion-exchange membranes by surface-initiated atom transfer radical polymerization of poly(glycidyl methacrylate) and subsequent derivatization with diethylamine

International Nuclear Information System (INIS)

Qian, Xiaolei; Fan, Hua; Wang, Chaozhan; Wei, Yinmao

2013-01-01

Ion-exchange membrane is of importance for the development of membrane chromatography. In this work, a high-capacity anion-exchange membrane was prepared by grafting of glycidyl methacrylate (GMA) onto the surface of regenerated cellulose (RC) membranes via surface-initiated atom transfer radical polymerization (SI-ATRP) and subsequent derivatization with diethylamine. Attenuated total reflectance Fourier-transform infrared (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were used to characterize changes in the chemical functionality, surface topography and pore morphology of the modified membranes. The static capacity of the prepared anion-exchange membrane was evaluated with bovine serum albumin (BSA) as a model protein. The results indicated that the anion-exchange membrane which could reach a maximum capacity of 96 mg/mL for static adsorption possesses a higher adsorption capacity, and the adsorption capacity increases with the polymerization time. The effect of pH and salt concentration confirmed that the adsorption of BSA followed ion-exchange mechanism. The established method would have potential application in the preparation of anion-exchange membrane.

A new pyrrolidone derivative from Pistacia chinensis

Institute of Scientific and Technical Information of China (English)

Jian Jun Liu; Chang An Geng; Xi Kui Liu

2008-01-01

A new N-phenyl-pyrrolidone derivative had been isolated from Pistacia chinesis Bunge. Its structure was elucidated as4-hydroxy-5-(2-oxo-1-pyrrolidinyl)-benzoic acid, named pistaciamide on the basis of the 1D-NMR, DEPT, HMQC and HMBCspectroscopic techniques.

Preparation and surface properties of mesoporous silica particles modified with poly(N-vinyl-2-pyrrolidone) as a potential adsorbent for bilirubin removal

Energy Technology Data Exchange (ETDEWEB)

Timin, Alexander, E-mail: a_timin@mail.ru [Inorganic Chemistry Department, Ivanovo State University of Chemistry and Technology (ISUCT), 7, Sheremetevsky prosp., 153000 Ivanovo (Russian Federation); Rumyantsev, Evgeniy, E-mail: evr@isuct.ru [Inorganic Chemistry Department, Ivanovo State University of Chemistry and Technology (ISUCT), 7, Sheremetevsky prosp., 153000 Ivanovo (Russian Federation); Lanin, Sergey N., E-mail: SNLanin@phys.chem.msu.ru [Chemistry Department, Physical Chemistry Division, Lomonosov Moscow State University, 1-3 Leninskie Gory, 119991 Moscow (Russian Federation); Rychkova, Sveta A. [Chemistry Department, Physical Chemistry Division, Lomonosov Moscow State University, 1-3 Leninskie Gory, 119991 Moscow (Russian Federation); Guseynov, Sabir S. [Krestov Institute of Solution Chemistry of Russian Academy of Sciences, 153000 Ivanovo (Russian Federation); Solomonov, Alexey V. [Inorganic Chemistry Department, Ivanovo State University of Chemistry and Technology (ISUCT), 7, Sheremetevsky prosp., 153000 Ivanovo (Russian Federation); Antina, Elena V. [Krestov Institute of Solution Chemistry of Russian Academy of Sciences, 153000 Ivanovo (Russian Federation)

2014-10-15

The surface of silica particles was modified with polyvinyl pyrrolidone (PVP) through sol–gel process. The different experimental techniques, i.e., thermogravimetric analysis (TGA and DTG), nitrogen adsorption, scanning electron microscopy (SEM), laser diffraction analysis (LDA), fourier transform spectroscopy (FTIR) are used to characterize the pure non-functionalized and functionalized silicas containing different amount of PVP. It was shown that PVP-modified silica samples have well developed porous structure; the values of specific surface area for PVP-modified silicas are in the range of 140–264 m{sup 2} g{sup −1}. While the non-functionalized silica shows the low surface area (S{sub BET} = 40 m{sup 2} g{sup −1}). The BJH analysis showed that PVP can be used as an effective agent to increase an average pore size and total pore volume. The results indicate that PVP functionalized silicas show a potential as effective adsorbents for bilirubin removal compared to other available adsorbents. - Highlights: • PVP functionalized silicas were synthesized via sol–gel method. • Modification of silica by PVP leads to the formation of mesoporous structure. • PVP functionalized mesoporous silicas demonstrate good adsorption properties for bilirubin removal.

Magnetic hydrophilic poly(2-hydroxyethyl methacrylate-co-glycidyl methacrylate) microspheres for DNA isolation from faeces

Czech Academy of Sciences Publication Activity Database

Trachtová, Š.; Obermajer, T.; Španová, A.; Matijašić, B. B.; Rogelj, I.; Horák, Daniel; Rittich, B.

2012-01-01

Roč. 555, č. 1 (2012), s. 263-270 ISSN 1542-1406. [International Conference on Frontiers of Polymers and Advanced Materials /11./. Pretoria, 22.05.2011-27.05.2011] R&D Projects: GA MŠk 2B06053 Institutional research plan: CEZ:AV0Z40500505 Keywords : DNA isolation * magnetic microspheres * mouse faeces Subject RIV: EE - Microbiology, Virology Impact factor: 0.530, year: 2012

A silicone rubber based composites using n-octadecane/poly (styrene-methyl methacrylate microcapsules as energy storage particle

Directory of Open Access Journals (Sweden)

W.L. Wu

Full Text Available A phase-change energy-storage material, silicone rubber (SR coated n-octadecane/poly (styrene-methyl methacrylate (SR/OD/P(St-MMA microcapsule composites, was prepared by mixing SR and OD/P(St-MMA microcapsules. The microcapsule content and silicone rubber coated method were investigated. The morphology and thermal properties of the composites were characterized by scanning electron microscopy (SEM, thermogravimetric analysis (TG, differential scanning calorimetry (DSC and heat storage properties. The results showed that the thermal and mechanical properties of SR/OD/P(St-MMA composites were excellent when the microcapsules were coated with room temperature vulcanized silicone rubber (RTVSR, of which content was 2 phr (per hundred rubber. The enthalpy value of the composites was 67.6 J g−1 and the composites were found to have good energy storage function. Keywords: n-Octadecane, Silicone rubber, Microcapsule, Energy-storage, Composites

Fabrication of thermo-responsive cotton fabrics using poly(vinyl caprolactam-co-hydroxyethyl acrylamide) copolymer.

Science.gov (United States)

Xiao, Min; González, Edurne; Monterroza, Alexis Martell; Frey, Margaret

2017-10-15

A thermo-responsive polymer with hydrophilic to hydrophobic transition behavior, poly(vinyl caprolactam-co-hydroxyethyl acrylamide) P(VCL-co-HEAA), was prepared by copolymerization of vinyl caprolactam and N-hydroxyethyl acrylamide via free radical solution polymerization. The resulting copolymer was characterized by Fourier transform infrared spectroscopy (FTIR), 1 H nuclear magnetic resonance (NMR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The lower critical solution temperature (LCST) of P(VCL-co-HEAA) was determined at 34.5°C. This thermo-responsive polymer was then grafted onto cotton fabrics using 1,2,3,4-butanetetracarboxylic acid (BTCA) as crosslinker and sodium hypophosphite (SHP) as catalyst. FTIR and energy dispersive X-ray spectroscopy (EDS) studies confirmed the successful grafting reaction. The modified cotton fabric exhibited thermo-responsive behavior as evidenced by water vapor permeability measurement confirming decreased permeability at elevated temperature. This is the first demonstration that a PVCL based copolymer is grafted to cotton fabrics. This study provides a new thermo-responsive polymer for fabrication of smart cotton fabrics with thermally switchable hydrophilicity. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preparation of epoxy-functionalized methyl methacrylate-butadiene-styrene core-shell particles and investigation of their dispersion in polyamide-6

NARCIS (Netherlands)

Aerdts, A.M.; Groeninckx, G.; Zirkzee, H.F.; Aert, van H.A.M.; Geurts, J.M.

1997-01-01

Functional core—shell impact modifiers of glycidyl methacrylate (GMA) functionalized methyl methacrylate—butadiene—styrene (MBS) have been prepared via a seeded semi-continuous emulsion polymerization. These functional MBS—GMA particles were blended with polyamide-6. Investigations by transmission

Comparative Studies with N-Methyl-2-Pyrrolidone and Furfural As Solvents for Extraction of Lube Distillates Etude comparative de deux solvants, la n-methyl-2 pyrrolidone et le furfural, pour l'extraction de distillats pour huiles lubrifiantes

OpenAIRE

Krishna R.; Singh H.; Kishore K.; Choudhary G. S.; Kaushik R. S.

2006-01-01

Solvent extraction of spindle raw lube distillate from Oman crude using n-methyl pyrrolidone (NMP) containing 1. 5wt. % water has been studied using a six-stage all-glass mixer-settler. Results of three operating temperatures with NMP are reported. A 65-55°C extraction temperature appears to be most appropriate for this stock. Data obtained at this temperature have been compared with those for furfural on the basis of phase boundary curves, extraction and lube refining indices and selectivity...

Multifunctional poly(alkyl methacrylate) films for dental care

International Nuclear Information System (INIS)

Nielsen, Birthe V; Nevell, Thomas G; Barbu, Eugen; Smith, James R; Tsibouklis, John; Rees, Gareth D

2011-01-01

Towards the evaluation of non-permanent dental coatings for their capacity to impart dental-care benefits, thin films of a homologous series of comb-like poly(alkyl methacrylate)s (ethyl to octadecyl) have been deposited, from aqueous latex formulations, onto dentally relevant substrates. AFM studies have shown that the thickness (40-300 nm) and surface roughness (8-12 nm) of coherent polymer films are influenced by the degree of polymerization and by the length of the pendant chain. Of the polymers under consideration, poly(butyl methacrylate) formed a close-packed film that conferred to dental substrates a high degree of inhibition to acid-mediated erosion (about 27%), as evaluated by released-phosphate determinations. The potential utility of the coatings to act as anti-sensitivity barriers has been evaluated by determining the hydraulic conductance of coated bovine-dentine substrates; single treatments of dentine discs with poly(butyl methacrylate) or with poly(ethyl methacrylate) effected mean respective reductions in fluid flow of about 23% with respect to water-treated controls; repeated applications of the poly(butyl methacrylate) latex led to mean reductions in fluid flow of about 80%. Chromometric measurements have shown that pellicle-coated hydroxyapatite discs treated with poly(butyl methacrylate), poly(hexyl methacrylate) or poly(lauryl methacrylate) exhibit significant resistance to staining by food chromogens.

Multifunctional poly(alkyl methacrylate) films for dental care

Energy Technology Data Exchange (ETDEWEB)

Nielsen, Birthe V; Nevell, Thomas G; Barbu, Eugen; Smith, James R; Tsibouklis, John [School of Pharmacy and Biomedical Sciences, University of Portsmouth, Portsmouth, Hampshire, PO1 2DT (United Kingdom); Rees, Gareth D [GlaxoSmithKline R and D, St George' s Avenue, Weybridge, Surrey, KT13 0DE (United Kingdom)

2011-02-15

Towards the evaluation of non-permanent dental coatings for their capacity to impart dental-care benefits, thin films of a homologous series of comb-like poly(alkyl methacrylate)s (ethyl to octadecyl) have been deposited, from aqueous latex formulations, onto dentally relevant substrates. AFM studies have shown that the thickness (40-300 nm) and surface roughness (8-12 nm) of coherent polymer films are influenced by the degree of polymerization and by the length of the pendant chain. Of the polymers under consideration, poly(butyl methacrylate) formed a close-packed film that conferred to dental substrates a high degree of inhibition to acid-mediated erosion (about 27%), as evaluated by released-phosphate determinations. The potential utility of the coatings to act as anti-sensitivity barriers has been evaluated by determining the hydraulic conductance of coated bovine-dentine substrates; single treatments of dentine discs with poly(butyl methacrylate) or with poly(ethyl methacrylate) effected mean respective reductions in fluid flow of about 23% with respect to water-treated controls; repeated applications of the poly(butyl methacrylate) latex led to mean reductions in fluid flow of about 80%. Chromometric measurements have shown that pellicle-coated hydroxyapatite discs treated with poly(butyl methacrylate), poly(hexyl methacrylate) or poly(lauryl methacrylate) exhibit significant resistance to staining by food chromogens.

Preparation of robust braid-reinforced poly(vinyl chloride) ultrafiltration hollow fiber membrane with antifouling surface and application to filtration of activated sludge solution.

Science.gov (United States)

Zhou, Zhuang; Rajabzadeh, Saeid; Fang, Lifeng; Miyoshi, Taro; Kakihana, Yuriko; Matsuyama, Hideto

2017-08-01

Braid-reinforced hollow fiber membranes with high mechanical properties and considerable antifouling surface were prepared by blending poly(vinyl chloride) (PVC) with poly(vinyl chloride-co-poly(ethylene glycol) methyl ether methacrylate) (poly(VC-co-PEGMA)) copolymer via non-solvent induced phase separation (NIPS). The tensile strength of the braid-reinforced PVC hollow fiber membranes were significantly larger than those of previously reported various types of PVC hollow fiber membranes. The high interfacial bonding strength indicated the good compatibility between the coating materials and the surface of polyethylene terephthalate (PET)-braid. Owing to the surface segregation phenomena, the membrane surface PEGMA coverage increased upon increasing the poly(VC-co-PEGMA)/PVC blending ratio, resulting in higher hydrophilicities and bovine serum albumin (BSA) repulsion. To compare the fouling properties, membranes with similar PWPs were prepared by adjusting the dope solution composition to eliminate the effect of hydrodynamic conditions on the membrane fouling performance. The blend membranes surface exhibited considerable fouling resistance to the molecular adsorption from both BSA solution and activated sludge solution. In both cases, the flux recovered to almost 80% of the initial flux using only water backflush. Considering their great mechanical properties and antifouling resistance to activated sludge solution, these novel membranes show good potential for application in wastewater treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

A silicone rubber based composites using n-octadecane/poly (styrene-methyl methacrylate) microcapsules as energy storage particle

Science.gov (United States)

Wu, W. L.; Chen, Z.

A phase-change energy-storage material, silicone rubber (SR) coated n-octadecane/poly (styrene-methyl methacrylate) (SR/OD/P(St-MMA)) microcapsule composites, was prepared by mixing SR and OD/P(St-MMA) microcapsules. The microcapsule content and silicone rubber coated method were investigated. The morphology and thermal properties of the composites were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TG), differential scanning calorimetry (DSC) and heat storage properties. The results showed that the thermal and mechanical properties of SR/OD/P(St-MMA) composites were excellent when the microcapsules were coated with room temperature vulcanized silicone rubber (RTVSR), of which content was 2 phr (per hundred rubber). The enthalpy value of the composites was 67.6 J g-1 and the composites were found to have good energy storage function.

Polyurethane/poly(vinyl alcohol hydrogel coating improves the cytocompatibility of neural electrodes

Directory of Open Access Journals (Sweden)

Mei Li

2015-01-01

Full Text Available Neural electrodes, the core component of neural prostheses, are usually encapsulated in polydimethylsiloxane (PDMS. However, PDMS can generate a tissue response after implantation. Based on the physicochemical properties and excellent biocompatibility of polyurethane (PU and poly(vinyl alcohol (PVA when used as coating materials, we synthesized PU/PVA hydrogel coatings and coated the surface of PDMS using plasma treatment, and the cytocompatibility to rat pheochromocytoma (PC12 cells was assessed. Protein adsorption tests indicated that the amount of protein adsorption onto the PDMS substrate was reduced by 92% after coating with the hydrogel. Moreover, the PC12 cells on the PU/PVA-coated PDMS showed higher cell density and longer and more numerous neurites than those on the uncoated PDMS. These results indicate that the PU/PVA hydrogel is cytocompatible and a promising coating material for neural electrodes to improve their biocompatibility.

Pyrrolidon carboxypeptidase activities in the hypothalamus-pituitary-thyroid and hypothalamus-pituitary-ovary axes of rats with mammary gland cancer induced by N-methyl nitrosourea.

Science.gov (United States)

Carrera, M P; Ramírez-Expósito, M J; Valenzuela, M T; García, M J; Mayas, M D; Arias de Saavedra, J M; Sánchez, R; Pérez, M C; Martínez-Martos, J M

2005-02-01

Pyrrolidon carboxypeptidase is an omega-peptidase that hydrolyses N-terminal pyroglutamyl residues from biologically active peptides such as gonadotropin-releasing and thyrotrophin-releasing hormones. We previously described a decrease in both rat and human pyrrolidon carboxypeptidase activity with breast cancer, suggesting that gonadotropin-releasing hormone may be an important local intracrine, autocrine and/or paracrine hormonal factor in the pathogenesis of breast cancer while playing a role in the tumoral process. However, the other susceptible substrate of pyrrolidon carboxypeptidase, thyrotrophin-releasing hormone, may also be modified with breast cancer, supporting an association between breast cancer and thyroid disorders. The present work analyses soluble and membrane-bound pyrrolidon carboxypeptidase activities in the hypothalamus-pituitary-thyroid and hypothalamus-pituitary-ovary axes in N-methyl nitrosourea-induced breast cancer in rats. Our aim was to determine the possible relationship between gonadotropin-releasing hormone and thyrotrophin-releasing hormone regulation through pyrrolidon carboxypeptidase activity. We propose that pyrrolidon carboxypeptidase activity dysregulation at various local and systemic levels may participate in the initiation, promotion and progression of breast cancer induced in rat by N-methyl nitrosourea through the increase in gonadotropin-releasing hormone. Since pyrrolidon carboxypeptidase activity also acts on thyrotrophin-releasing hormone, the dysregulation of this enzyme's activity could indirectly affect hypothalamus-pituitary-thyroid axis function, and thus potentially represent a link between the diseases of thyroid and breast cancer.

Effect of doping (C or N) and co-doping (C+N) on the photoactive properties of magnetron sputtered titania coatings for the application of solar water-splitting.

Science.gov (United States)

Rahman, M; Dang, B H Q; McDonnell, K; MacElroy, J M D; Dowling, D P

2012-06-01

The photocatalytic splitting of water into hydrogen and oxygen using a photoelectrochemical (PEC) cell containing titanium dioxide (TiO2) photoanode is a potentially renewable source of chemical fuels. However, the size of the band gap (-3.2 eV) of the TiO2 photocatalyst leads to its relatively low photoactivity toward visible light in a PEC cell. The development of materials with smaller band gaps of approximately 2.4 eV is therefore necessary to operate PEC cells efficiently. This study investigates the effect of dopant (C or N) and co-dopant (C+N) on the physical, structural and photoactivity of TiO2 nano thick coating. TiO2 nano-thick coatings were deposited using a closed field DC reactive magnetron sputtering technique, from titanium target in argon plasma with trace addition of oxygen. In order to study the influence of doping such as C, N and C+N inclusions in the TiO2 coatings, trace levels of CO2 or N2 or CO2+N2 gas were introduced into the deposition chamber respectively. The properties of the deposited nano-coatings were determined using Spectroscopic Ellipsometry, SEM, AFM, Optical profilometry, XPS, Raman, X-ray diffraction UV-Vis spectroscopy and tri-electrode potentiostat measurements. Coating growth rate, structure, surface morphology and roughness were found to be significantly influenced by the types and amount of doping. Substitutional type of doping in all doped sample were confirmed by XPS. UV-vis measurement confirmed that doping (especially for C doped sample) facilitate photoactivity of sputtered deposited titania coating toward visible light by reducing bandgap. The photocurrent density (indirect indication of water splitting performance) of the C-doped photoanode was approximately 26% higher in comparison with un-doped photoanode. However, coating doped with nitrogen (N or N+C) does not exhibit good performance in the photoelectrochemical cell due to their higher charge recombination properties.

Synthesis, characterization, and corrosion protection properties of poly(N-(methacryloyloxymethyl) benzotriazole-co-methyl methacrylate) on mild steel

Energy Technology Data Exchange (ETDEWEB)

Srikanth, A.P. [Department of Applied Sciences and Humanities, MIT Campus, Anna University, Chennai 600044 (India); Lavanya, A. [Department of Chemistry, CEG Campus, Anna University, Chennai 600025 (India); Nanjundan, S. [Department of Chemistry, CEG Campus, Anna University, Chennai 600025 (India); Rajendran, N. [Department of Applied Sciences and Humanities, MIT Campus, Anna University, Chennai 600044 (India)]. E-mail: nrajendran@annauniv.edu

2006-12-15

The copolymers from different feed ratios of N-(methacryloyloxymethyl) benzotriazole (MMBT) and methyl methacrylate (MMA) has been synthesised using free radical solution polymerization technique and characterized using FT-IR and {sup 13}C NMR spectroscopy. The thermal stability of the polymers was studied using theremogravimetrtic analysis (TGA). The corrosion behaviors of mild steel specimens dip coated with different composition of copolymers have been evaluated by potentiodynamic polarization and electrochemical impedance spectroscopic (EIS) method. These electrochemical properties were observed in 0.1 M HCl medium. The polarization and impedance measurements showed different corrosion protection efficiency with change in composition of the copolymers. It was found that the corrosion protection properties are owing to the barrier effect of the polymer layer covered on the mild steel surfaces. However, it was observed that the copolymer obtained from 1:1 mole ratio of MMBT and MMA exhibited better protection efficiency than other combinations.

Synthesis, characterization, and corrosion protection properties of poly( N-(methacryloyloxymethyl) benzotriazole- co-methyl methacrylate) on mild steel

Science.gov (United States)

Srikanth, A. P.; Lavanya, A.; Nanjundan, S.; Rajendran, N.

2006-12-01

The copolymers from different feed ratios of N-(methacryloyloxymethyl) benzotriazole (MMBT) and methyl methacrylate (MMA) has been synthesised using free radical solution polymerization technique and characterized using FT-IR and 13C NMR spectroscopy. The thermal stability of the polymers was studied using theremogravimetrtic analysis (TGA). The corrosion behaviors of mild steel specimens dip coated with different composition of copolymers have been evaluated by potentiodynamic polarization and electrochemical impedance spectroscopic (EIS) method. These electrochemical properties were observed in 0.1 M HCl medium. The polarization and impedance measurements showed different corrosion protection efficiency with change in composition of the copolymers. It was found that the corrosion protection properties are owing to the barrier effect of the polymer layer covered on the mild steel surfaces. However, it was observed that the copolymer obtained from 1:1 mole ratio of MMBT and MMA exhibited better protection efficiency than other combinations.

RAFT Aqueous Dispersion Polymerization of N-(2-(Methacryloyloxy)ethyl)pyrrolidone: A Convenient Low Viscosity Route to High Molecular Weight Water-Soluble Copolymers.

Science.gov (United States)

Cunningham, Victoria J; Derry, Matthew J; Fielding, Lee A; Musa, Osama M; Armes, Steven P

2016-06-28

RAFT solution polymerization of N -(2-(methacryoyloxy)ethyl)pyrrolidone (NMEP) in ethanol at 70 °C was conducted to produce a series of PNMEP homopolymers with mean degrees of polymerization (DP) varying from 31 to 467. Turbidimetry was used to assess their inverse temperature solubility behavior in dilute aqueous solution, with an LCST of approximately 55 °C being observed in the high molecular weight limit. Then a poly(glycerol monomethacylate) (PGMA) macro-CTA with a mean DP of 63 was chain-extended with NMEP using a RAFT aqueous dispersion polymerization formulation at 70 °C. The target PNMEP DP was systematically varied from 100 up to 6000 to generate a series of PGMA 63 -PNMEP x diblock copolymers. High conversions (≥92%) could be achieved when targeting up to x = 5000. GPC analysis confirmed high blocking efficiencies and a linear evolution in M n with increasing PNMEP DP. A gradual increase in M w / M n was also observed when targeting higher DPs. However, this problem could be minimized ( M w / M n RAFT aqueous dispersion polymerization of NMEP was approximately four times faster than the RAFT solution polymerization of NMEP in ethanol when targeting the same DP in each case. This is perhaps surprising because both 1 H NMR and SAXS studies indicate that the core-forming PNMEP chains remain relatively solvated at 70 °C in the latter formulation. Moreover, dissolution of the initial PGMA 63 -PNMEP x particles occurs on cooling from 70 to 20 °C as the PNMEP block passes through its LCST. Hence this RAFT aqueous dispersion polymerization formulation offers an efficient route to a high molecular weight water-soluble polymer in a rather convenient low-viscosity form. Finally, the relatively expensive PGMA macro-CTA was replaced with a poly(methacrylic acid) (PMAA) macro-CTA. High conversions were also achieved for PMAA 85 -PNMEP x diblock copolymers prepared via RAFT aqueous dispersion polymerization for x ≤ 4000. Again, better control was achieved when

Covalently coating dextran on macroporous polyglycidyl methacrylate microsphere enabled rapid protein chromatographic separation

International Nuclear Information System (INIS)

Zhang, Rongyue; Li, Qiang; Li, Juan; Zhou, Weiqing; Ye, Peili; Gao, Yang; Ma, Guanghui; Su, Zhiguo

2012-01-01

Protein denaturation and nonspecific adsorption on polymer media as a chromatographic support have been a problem which needs to be overcome. Macroporous poly(glycidyl methacrylate–divinylbezene) (PGMA–DVB) microspheres prepared in this study were firstly covalently coated with dextran through a three-step method. The dextran was firstly adsorbed onto the microspheres and then covalently bound to the PGMA–DVB microsphere through ether bonds which were formed by hydroxyl group reacting with epoxy group at the presence of 4-(Dimethylamino) pyridine. Finally, the coating dextran layer was crosslinked by ethylene glycol diglycidyl ether to form the continuous network coating. The coated microspheres were characterized by Fourier transform infrared spectra, scanning electron microscope, mercury porosimetry measurements, laser scanning confocal microscope, and protein adsorption experiments. Results showed that PGMA–DVB microspheres coated with dextran successfully maintained the macroporous structure and high permeability. The backpressure was only 1.69 MPa at a high flow rate of 2891 cm/h. Consequently, the hydrophilicity and biocompatibility of modified microspheres were greatly improved, and the contact angle decreased from 184° to 13°, and nonspecific adsorption of proteins was decreased to little or none. The clad dextran coating with large amounts of hydroxyl group was easily derived to be various functional groups. The derived media have great potential applications in rapid protein chromatography. - Highlights: ► Macroporous PGMA–DVB microspheres were covalently coated with dextran. ► The hydrophilicity of the coated microspheres was significantly improved. ► The irreversible adsorption of proteins was reduced to zero. ► The coated microspheres can maintain the macropore structure. ► The coated microspheres were applied to rapid protein separation.

Radiation-Induced Grafting for the Synthesis of Adsorbents for Phosphate and Chromate Removal from Aqueous Systems

Energy Technology Data Exchange (ETDEWEB)

Kavakli, P A; Kavakli, C; Guven, O [Department of Chemistry, Hacettepe University, Beytepe, 06800, Ankara (Turkey)

2012-09-15

Nonwoven fabrics made of PE coated PP fibres were irradiated by accelerated electrons in inert atmospheres for grafting of two different monomers, glycidyl methacrylate and dimethylaminoethyl methacrylate. Grafting conditions were optimized by a systematic investigation of the effects of absorbed dose, monomer concentration, grafting reaction temperature and duration. 150% grafted copolymers were later modified by protonation and quaternization of poly(dimethylaminoethyl methacrylate) chains and by Cu(II) loading of dipyridyl amine modified poly(glycidyl methacrylate) graft chains. The PE/PP based adsorbents thus prepared were used for their suitability of removing phosphate and chromate ions from aqueous systems. Adsorption/removal studies were carried out in both batch and continuous flow type systems. The selectivity of adsorption of phosphate ions in the presence of other competing anions were also checked showing the enhanced selectivity for phosphate ions. (author)

Porous polymer monoliths functionalized through copolymerization of a C60 fullerene-containing methacrylate monomer for highly efficient separations of small molecules

KAUST Repository

Chambers, Stuart D.; Holcombe, Thomas W.; Švec, František; Frechet, Jean

2011-01-01

been prepared and their chromatographic performance have been tested for the separation of small molecules in the reversed phase. While addition of the C60-fullerene monomer to the glycidyl methacrylate-based monolith enhanced column efficiency 18-fold

Radioisotope investigations on the stratigraphic distribution of poly/methyl methacrylate/grafted onto leather

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1984-01-01

Investigations on the stratigraphic distribution of poly/methyl methacrylate/ in leather follow our earlier experiments on radiation grafting of vinyl monomers in situ. Polymer distribution was determined for pigskins and cattlehides tanned with basic sulphates of chromium/III/. 14 C-labelled methyl methacrylate was used in present experiments. Precision slicing technique was employed to cut consecutive slices parallel to the grain surface of the radiation modified leather. Quantative analysis of polymer distribution in leather was based on radioactivity measurements. Each layer was burned in Oxymat apparatus and resulting 14 CO 2 was analysed by liquid scintillation method. On the basis of radioactivity measurements and visual observations with light microscope conclusion on desirable distribution of polymer was reached. In the midcorium part of leather polymer is evenly distributed and its content is much higher than for outer layers next to surface and flesh. Mechanism of relevant processes as well as formation and role played by peroxide compounds is discussed

Radioisotope investigations on the stratigraphic distribution of poly(methyl methacrylate) grafted onto leather

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1985-01-01

Investigations on the stratigraphic distribution of poly(methyl methacrylate) in leather follow our earlier experiments on radiation grafting of vinyl monomers in situ. Polymer distribution was determined for pigskins and cattlehides tanned with basic sulphates of chromium (III). 14 C-labelled methyl methacrylate was used in present experiments. Precision slicing technique was employed to cut consecutive slices parallel to the grain surface of the radiation modified leather. Quantitative analysis of polymer distribution in leather was based on radioactivity measurements. Each layer was burned in Oxymat apparatus and resulting 14 CO 2 was analysed by liquid scintillation method. On the basis of radioactivity measurements and visual observations with light microscope conclusion on desirable distribution of polymer was reached. In the midcorium part of leather polymer is evenly distributed and its content is much higher than for outer layers next to surface and flesh. Mechanism of relevant processes as well as formation and role played by peroxide compounds are discussed. (author)

Method for coating a resinous coating material. [electron beam irradiation

Energy Technology Data Exchange (ETDEWEB)

Ino, T; Fujioka, S; Mibae, J; Takahashi, M

1968-07-13

The strength, flexibility and durability of a vinyl chloride resin, acryl resin and the like are improved. This method of application comprises the steps of applying and thereafter radically curing a mixture composed of a polymer (II) having double bond(s) on its side chain and an ethylenic unsaturated monomer, said polymer (II) being obtained by the reaction between an unsaturated carboxylic acid or anhydride represented by the formula XCH = CHY (X = (CH/sub 2/)sub(n)COOH, where 0 <= n <= 2, Y = COOR/sub 1/ or R/sub 2/(R/sub 1/ and R/sub 2/ are hydrogen or an alkyl group having from 1 to 10 atoms of carbon)) and the acrylic copolymer (I), containing a hydroxyl group, obtained by copolymerization of 10 to 50% by weight of at least one selected from the group of beta-hydroxy alkyl acrylate, beta-hydroxy alkyl methacrylate, N-methylol acrylamide and N-methylol methacryl amide with at least one selected from the group of acrylic ester, methacrylic ester and stylene. The copolymer (I) can be obtained by the usual radical polymerization such as bulk polymerization, solution polymerization, suspension polymerization or the like. The polymer (II) is dissolved in the ethylenic unsaturated monomer and radically cured with radical polymerization catalysts or electron beams, etc. The energy range of the electron beams may be 0.1 to 3 MeV. Any type of electron accelerator may be used.

Preparation of nanogels by radiation-induced cross-linking of interpolymer complexes of poly (acrylic acid) with poly (vinyl pyrrolidone) in aqueous medium

Science.gov (United States)

Ghaffarlou, Mohammadreza; Sütekin, S. Duygu; Güven, Olgun

2018-01-01

Functional nanogels were prepared from interpolymer complexes (IPC) of poly (vinyl pyrrolidone) and poly (acrylic acid) by gamma irradiation of their aqueous solutions. The coil size of IPCs prepared under different experimental conditions (polymer molecular weight, concentration, mixing ratios, pH and temperature) were measured by Dynamic Light Scattering (DLS) technique prior to irradiation. At relatively low absorbed doses of 5 and 10 kGy, IPC nanogels with a range of 30-250 nm diameters, -12 to -28 mV zeta potentials and polydispersities lower than 0.17 were obtained. The sizes of the nanogels were found to be smaller than the size of the precursor IPC coil sizes (40-300 nm) due to the formation of intra-chain crosslinks. Thus a recipe of preparing multifunctional nanogels with double amphiphilic properties carrying polyacidic and nonionic polymer structures with the range of above listed properties has been developed. These nanogels show narrow size distribution and high colloidal stability increasing their potential to be used as biocompatible drug carriers with controlled-release properties. PVP-PAA IPC nanogels were characterized by dynamic light scattering (DLS), atomic force microscopy (AFM) and scanning electron microscopy (SEM) techniques.

Effect of gamma ray on poly(lactic acid)/poly(vinyl acetate-co-vinyl alcohol) blends as biodegradable food packaging films

Science.gov (United States)

Razavi, Seyed Mohammad; Dadbin, Susan; Frounchi, Masoud

2014-03-01

Poly(lactic acid) (PLA)/poly(vinyl acetate-co-vinyl alcohol) [P(VAc-co-VA)] blends as new transparent film packaging materials were prepared at various blend compositions and different vinyl alcohol contents. The blends and pure PLA were irradiated by gamma rays to investigate the extent of changes in the packaging material during gamma ray sterilization process. The miscibility of the blends was dependent on the blend composition and vinyl alcohol content; gamma irradiation had little effect on the extent of miscibility. The glass transition temperature of pure PLA and PLA/P(VAc-co-VA) miscible blends reduced after irradiation. On the other hand in PLA/P(VAc-co-VA) immiscible blends, while the glass transition temperature of the PLA phase decreased; that of the copolymer phase slightly increased. The reduction in the glass transition was about 10 percent for samples irradiated with 50 kGy indicating dominance of chain scission of PLA molecules at high irradiation dose. The latter was verified by drop in mechanical properties of pure PLA after exposing to gamma irradiation at 50 kGy. Blending of PLA with the copolymer P(VAc-co-VA) compensated greatly the adverse effects of irradiation on PLA. The oxygen-barrier property of the blend was superior to the neat PLA and remained almost intact with irradiation. The un-irradiated and irradiated blends had excellent transparency. Gamma ray doses used for sterilization purposes are usually less than 20 kGy. It was shown that gamma irradiation at 20 kGy had no or little adverse effects on PLA/P(VAc-co-VA) blends mechanical and gas barrier properties.

Polymethyl methacrylate-co-methacrylic acid coatings with controllable concentration of surface carboxyl groups: A novel approach in fabrication of polymeric platforms for potential bio-diagnostic devices

International Nuclear Information System (INIS)

Hosseini, Samira; Ibrahim, Fatimah; Djordjevic, Ivan; Koole, Leo H.

2014-01-01

Highlights: • Synthesis and processing of PMMA-co-MAA spin-coatings on silicon wafers. • Surface chemistry and morphology as a function of tailored co-polymer structure. • Polymer coatings with controlled number of surface carboxyl groups. - Abstract: The generally accepted strategy in development of bio-diagnostic devices is to immobilize proteins on polymeric surfaces as a part of detection process for diseases and viruses through antibody/antigen coupling. In that perspective, polymer surface properties such as concentration of functional groups must be closely controlled in order to preserve the protein activity. In order to improve the surface characteristics of transparent polymethacrylate plastics that are used for diagnostic devices, we have developed an effective fabrication procedure of polymethylmetacrylate-co-metacrylic acid (PMMA-co-MAA) coatings with controlled number of surface carboxyl groups. The polymers were processed effectively with the spin-coating technique and the detailed control over surface properties is here by demonstrated through the variation of a single synthesis reaction parameter. The chemical structure of synthesized and processed co-polymers has been investigated with nuclear magnetic resonance spectroscopy (NMR) and matrix-assisted laser desorption time-of-flight mass spectrometry (MALDI-ToF-MS). The surface morphology of polymer coatings have been analyzed with atomic force microscopy (AFM) and scanning electron microscopy (SEM). We demonstrate that the surface morphology and the concentration of surface –COOH groups (determined with UV–vis surface titration) on the processed PMMA-co-MAA coatings can be precisely controlled by variation of initial molar ratio of reactants in the free-radical polymerization reaction. The wettability of developed polymer surfaces also varies with macromolecular structure

Polymethyl methacrylate-co-methacrylic acid coatings with controllable concentration of surface carboxyl groups: A novel approach in fabrication of polymeric platforms for potential bio-diagnostic devices

Energy Technology Data Exchange (ETDEWEB)

Hosseini, Samira; Ibrahim, Fatimah [Center for Innovation in Medical Engineering, Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Djordjevic, Ivan, E-mail: ivan.djordjevic@um.edu.my [Center for Innovation in Medical Engineering, Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Koole, Leo H. [Center for Innovation in Medical Engineering, Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Department of Biomedical Engineering, Faculty of Health. Medicine and Life Science, Maastricht University, PO Box 616, NL 6200 MD Maastricht (Netherlands)

2014-05-01

Highlights: • Synthesis and processing of PMMA-co-MAA spin-coatings on silicon wafers. • Surface chemistry and morphology as a function of tailored co-polymer structure. • Polymer coatings with controlled number of surface carboxyl groups. - Abstract: The generally accepted strategy in development of bio-diagnostic devices is to immobilize proteins on polymeric surfaces as a part of detection process for diseases and viruses through antibody/antigen coupling. In that perspective, polymer surface properties such as concentration of functional groups must be closely controlled in order to preserve the protein activity. In order to improve the surface characteristics of transparent polymethacrylate plastics that are used for diagnostic devices, we have developed an effective fabrication procedure of polymethylmetacrylate-co-metacrylic acid (PMMA-co-MAA) coatings with controlled number of surface carboxyl groups. The polymers were processed effectively with the spin-coating technique and the detailed control over surface properties is here by demonstrated through the variation of a single synthesis reaction parameter. The chemical structure of synthesized and processed co-polymers has been investigated with nuclear magnetic resonance spectroscopy (NMR) and matrix-assisted laser desorption time-of-flight mass spectrometry (MALDI-ToF-MS). The surface morphology of polymer coatings have been analyzed with atomic force microscopy (AFM) and scanning electron microscopy (SEM). We demonstrate that the surface morphology and the concentration of surface –COOH groups (determined with UV–vis surface titration) on the processed PMMA-co-MAA coatings can be precisely controlled by variation of initial molar ratio of reactants in the free-radical polymerization reaction. The wettability of developed polymer surfaces also varies with macromolecular structure.

Regulating the migration of smooth muscle cells by a vertically distributed poly(2-hydroxyethyl methacrylate) gradient on polymer brushes covalently immobilized with RGD peptides.

Science.gov (United States)

Wu, Sai; Du, Wang; Duan, Yiyuan; Zhang, Deteng; Liu, Yixiao; Wu, Bingbing; Zou, Xiaohui; Ouyang, Hongwei; Gao, Changyou

2018-05-30

The gradient localization of biological cues is of paramount importance to guide directional migration of cells. In this study, poly(2-hydroxyethyl methacrylate-co-glycidyl methacrylate)-block- poly(2-hydroxyethyl methacrylate) (P(HEMA-co-GMA)-b-PHEMA) brushes with a uniform underneath P(HEMA-co-GMA) layer and a gradient thickness of PHEMA blocks were prepared by using surface-initiated atom-transfer radical polymerization and a dynamically controlled polymerization process. The polymer chains were subsequently functionalized with the cell-adhesive arginine-glycine-aspartic acid (RGD) peptides by reaction with the glycidyl groups, and their structures and properties were characterized by X-ray photoelectron spectrometry (XPS), quartz crystal microbalance with dissipation (QCM-D) and air contact angle. Adhesion and migration processes of smooth muscle cells (SMCs) were then studied. Compared with those on the sufficiently exposed RGD surface, the cell adhesion and mobility were well maintained when the RGD peptides were localized at 18.9 nm depth, whereas the adhesion, spreading and migration rate of SMCs were significantly impaired when the RGD peptides were localized at a depth of 38.4 nm. On the RGD depth gradient surface, the SMCs exhibited preferential orientation and enhanced directional migration toward the direction of reduced thickness of the second PHEMA brushes. Half of the cells were oriented within ± 30° to the x-axis direction, and 72% of the cells moved directionally at the optimal conditions. Cell adhesion strength, arrangement of cytoskeleton, and gene and protein expression levels of adhesion-related proteins were studied to corroborate the mechanisms, demonstrating that the cell mobility is regulated by the complex and synergetic intracellular signals resulted from the difference in surface properties. Cell migration is of paramount importance for the processes of tissue repair and regeneration. So far, the gradient localization of

Synthesis of iron nanoparticles with poly(1-vinylpyrrolidone-co-vinyl acetate) and its application to nitrate reduction

DEFF Research Database (Denmark)

Lee, Nara; Choi, Kyunghoon; Uthuppu, Basil

2014-01-01

This study aimed to synthesize dispersed and reactive nanoscale zero-valent iron (nZVI) with poly(1-vinylpyrrolidone-co-vinyl acetate) (PVP/VA), nontoxic and biodegradable stabilizer. The nZVI used for the experiments was prepared by reduction of ferric solution in the presence of PVP/VA with spe...

Effect of Compatibilization on Poly-ε-Caprolactone Grafting onto Poly(ethylene-co-vinyl alcohol

Directory of Open Access Journals (Sweden)

Mohamed Taha

2011-10-01

Full Text Available The non-miscibility of the reactants during solvent free poly-ε-caprolactone grafting onto poly(ethylene-co-vinyl alcohol (EVOH dramatically affects reaction kinetics. Different solutions were proposed to accelerate the exchange reactions between poly(ethylene-co-vinyl alcohol and poly-ε-caprolactone. Reactions were conducted in a batch reactor or a mini twin-screw extruder. The addition of a poly(ethylene-co-vinyl alcohol-g-poly-ε-caprolactone copolymer increased the compatibility of the reactants and led to a higher reaction rate. This copolymer was either prepared separately and added at the reaction beginning or prepared in situ grafting caprolactone from EVOH. The reactive system evolution was analyzed using molar mass evolution, microstructure characterization, thermal properties and the reactive blend morphology. The compatibilization effect combined with optimized reaction conditions, such as concentration and nature of catalyst and temperature, resulted in an important increase in reaction rates. Among the tested catalysts, 1,5,7-Triazabicyclo [4.4.0]dec-5-ene was a more efficient catalyst for grafting reactions than Tin (II 2-ethylhexanoate.

Synthesis and Characterization of Poly(hydroxyethyl methacrylate-co-methacrylic acid) Cross Linked Polymeric Network for the Delivery of Analgesic Agent

International Nuclear Information System (INIS)

Rashid, H.; Ahmad, M.; Minhas, M. U.; Aamir, M. F.; Sohail, M.

2015-01-01

Objective of the study was to synthesize a chemically cross-linked poly(hydroxyethylmethacrylate-co-methacrylic acid) hydrogel (p(HEMA-co-MAA hydrogel)) for pH-responsive, controlled drug delivery of Flurbiprofen. pH-sensitive hydrogel drug delivery system was synthesized with the help of poly hydroxyethyl methacrylate (HEMA) and methacrylic acid (MAA) by using ethylene glycol dimethacrylate (EGDMA) as crosslinker. The monomers (HEMA and MAA) were successfully cross linked through free radical polymerization process, initiated by benzoyl peroxide in an aqueous medium. All formulations were loaded with Flurbiprofen as a model drug and evaluated at pH 1.2 and pH 7.4 to investigate pH-responsive nature of the system. Fourier transform infrared spectroscopy (FTIR) was performed to confirm the cross-linking of copolymer while thermo gravimetric analysis (TGA) and differential scanning calorimetry (DSC) were performed to evaluate the thermal stability of the system. Swelling studies and in-vitro release studies were carried out to evaluate pH-responsive nature of the hydrogels. FTIR confirmed that monomers were successfully cross-linked to form a copolymer. Hydrogel system showed less swelling at lower pH while at higher pH, it showed higher swelling, releasing drug in the same fashion. It was concluded that a stable hydrogel network was chemically cross-linked showing pH-responsive nature and thus, synthesized p(HEMA-co-MAA) hydrogels can be successfully employed as potential candidate for controlled drug delivery. (author)

Fabrication and evaluation of atmospheric plasma spraying WC-Co-Cu-MoS2 composite coatings

International Nuclear Information System (INIS)

Yuan Jianhui; Zhu Yingchun; Zheng Xuebing; Ji Heng; Yang Tao

2011-01-01

Research highlights: → Protective WC-Co-based coatings containing solid lubricant Cu and MoS 2 used in wear applications were investigated in this study. → It was found that the MoS 2 composition in the feed powder was kept in WC-Co-Cu-MoS 2 coatings, and the decomposition and decarburization of WC in APS process were improved. → Combining the wear resistance of WC with the lubricating properties of Cu and MoS 2 has an extremely beneficial effect on improving the tribological performance of the resulting coating. - Abstract: Protective WC-Co-based coatings containing solid lubricant Cu and MoS 2 used in wear applications were investigated in this study. These coatings were deposited on mild steel substrates by atmospheric plasma spraying (APS). The feedstock powders were prepared by mechanically mixing the solid lubricant powders and WC-Co powder, followed by sintering and crushing the mixtures to avoid different particle flighting trajectories at plasma. The tribological properties of the coatings against stainless steel balls were examined by ball-on-disk (BOD) tribometer under normal atmospheric condition. The microstructure of the coatings was studied by optical microscope, scanning electron microscope and X-ray diffraction. It was found that the MoS 2 composition in the feed powder was kept in WC-Co-Cu-MoS 2 coatings, and the decomposition and decarburization of WC in APS process were improved, which were attributed to the protection of Cu around them. The friction and wear behaviors of all the WC-Co-Cu-MoS 2 coatings were superior to that of WC-Co coating. Such behavior was associated to different wear mechanisms operating for WC-Co coating and the WC-Co-Cu-MoS 2 coatings.

Overmodulation Control in the Optimization of a H-PDLC Device with Ethyl Eosin as Dye

Directory of Open Access Journals (Sweden)

Manuel Ortuño

2013-01-01

Full Text Available The response of a H-PDLC device is improved by means of a two-step method. First, component optimization—initiator system, crosslinker, and cosolvent—enables the diffraction efficiency of the hologram to be maximized. Second, the use of N-methyl-2-pyrrolidone in combination with N-vinyl-2-pyrrolidone prevents the overmodulation in photopolymers containing ethyl eosin.

Wear resistance of nano- and micro-crystalline diamond coatings onto WC-Co with Cr/CrN interlayers

Energy Technology Data Exchange (ETDEWEB)

Polini, Riccardo [Dipartimento di Scienze e Tecnologie Chimiche, Universita di Roma Tor Vergata, Via della Ricerca Scientifica, 1, Rome, 00133 (Italy); Barletta, Massimiliano, E-mail: barletta@ing.uniroma2.i [Dipartimento di Ingegneria Meccanica, Universita di Roma Tor Vergata, Via del Politecnico, 1, Rome, 00133 (Italy); Cristofanilli, Giacomo [Dipartimento di Scienze e Tecnologie Chimiche, Universita di Roma Tor Vergata, Via della Ricerca Scientifica, 1, Rome, 00133 (Italy)

2010-12-30

Cr/CrN bi-layers have been used recently to promote the growth of high quality Hot Filament Chemical Vapour Deposition (HFCVD) diamond coatings onto Co-cemented tungsten carbide (WC-6 wt.%Co) substrates. In the present investigation, the influence of the crystalline size of the diamond coatings on their wear endurance is looked into. Nano- (NDC) and micro-crystalline Diamond Coatings (MDC) were deposited by HFCVD onto untreated and Fluidized Bed (FB) treated Cr/CrN interlayers. NDCs, characterized by a cauliflower-like morphology, showed improved wear resistance. However, the superimposition of NDCs onto Cr/CrN interlayers micro-corrugated by FB treatment was found to be the most promising choice, leading to the formation of highly adherent and wear resistant coatings.

CO2-Switchable Membranes Prepared by Immobilization of CO2-Breathing Microgels.

Science.gov (United States)

Zhang, Qi; Wang, Zhenwu; Lei, Lei; Tang, Jun; Wang, Jianli; Zhu, Shiping

2017-12-20

Herein, we report the development of a novel CO 2 -responsive membrane system through immobilization of CO 2 -responsive microgels into commercially available microfiltration membranes using a method of dynamic adsorption. The microgels, prepared from soap-free emulsion polymerization of CO 2 -responsive monomer 2-(diethylamino)ethyl methacrylate (DEA), can be reversibly expanded and shrunken upon CO 2 /N 2 alternation. When incorporated into the membranes, this switching behavior was preserved and further led to transformation between microfiltration and ultrafiltration membranes, as indicated from the dramatic changes on water flux and BSA rejection results. This CO 2 -regulated performance switching of membranes was caused by the changes of water transportation channel, as revealed from the dynamic water contact angle tests and SEM observation. This work represents a simple yet versatile strategy for making CO 2 -responsive membranes.

Large scale solvothermal synthesis and a strategy to obtain stable Langmuir–Blodgett film of CoFe2O4 nanoparticles

International Nuclear Information System (INIS)

Thampi, Arya; Babu, Keerthi; Verma, Seema

2013-01-01

Highlights: • Large scale, monodisperse CoFe 2 O 4 nanoparticles by solvothermal route. • LB technique to obtain stable film of CoFe 2 O 4 nanoparticles over a large area. • Hydrophobicity of substrate was enhanced utilizing LB films of cadmium arachidate. • P–A isotherm and AFM cross sectional height profile analysis confirms stability. • Large scale organization of nanoparticles for surface pressure higher than 15 mN/m. -- Abstract: Nearly monodisperse oleic acid coated cobalt ferrite nanoparticles were synthesized in large scale by a simple solvothermal method utilizing N-methyl 2-Pyrrolidone (NMP) as a high boiling solvent. The magnetic oxide was further investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and vibrating sample magnetometer (VSM). Langmuir–Blodgett (LB) technique is discussed to obtain a 2D assembly of oleic acid coated CoFe 2 O 4 nanoparticles over a large area. We describe a method to obtain stable, condensed three layers of cadmium arachidate on a piranha treated glass substrate. The hydrophobic surface thus obtained was subsequently used for forming a stable monolayer of oleic acid stabilized cobalt ferrite nanoparticles at the air–water interface. The stability of the LB films at the air–water interface was studied by pressure–area isotherm curves and atomic force microscopy (AFM) cross sectional height profile analysis. 2D organization of the magnetic nanoparticles at different surface pressures was studied by TEM. Preparation of large area LB films of CoFe 2 O 4 nanoparticles is reported for a surface pressure more than 15 mN/m

Effect of H2O and Y(O on Oxidation Behavior of NiCoCrAl Coating Within Thermal Barrier Coating

Directory of Open Access Journals (Sweden)

WANG Yi-qun

2017-04-01

Full Text Available NiCoCrAl coatings containing Y and Y oxide were made using vacuum plasma deposition and high-velocity oxygen fuel respectively, high temperature oxidation dynamics and cross-section microstructures of NiCoCrAl+Y and NiCoCrAl+Y(O coatings in Ar-16.7%O2, Ar-3.3%H2O and Ar-0.2%H2-0.9%H2O at 1100℃ were investigated by differential thermal analysis (DTA and optical and electron microscope. The influencing mechanism of Y oxide on the oxidation of coatings at different atmosphere was compared by computation using First-Principles. The results show that Al2O3 layer on NiCoCrAl+Y coatings has more holes for internal oxidation on account of the element Y diffusion and enrichment on the interface. In addition, steam can promote the internal oxidation. While a thinner and uniform alumina form on NiCoCrAl+Y(O coatings because element Y is pinned by oxygen atoms during the preparation of coatings. Water vapor has less influence on protective alumina formation on the NiCoCrAl+Y(O coating. Therefore, oxidation behavior of NiCoCrAl coatings vary in composition and structure in different oxidizing atmosphere. Besides, Y and Y-enrichment oxides have key influences on the microstructure and the growth rate.

Preparation and characterization of coating sodium trisilicate (Na2O.nSiO2) at calcium carbonate (CaCO3) for blowing agent in Mg alloy foam

Science.gov (United States)

Erryani, Aprilia; Lestari, Franciska Pramuji; Annur, Dhyah; Kartika, Ika

2018-05-01

The role of blowing agent in the manufacture of porous metal alloys is very important to produce the desired pore. The thermal stability and speed of foam formation have an effect on the resulting pore structure. In porous metal alloys, uniformity of size and pore deployment are the main determinants of the resulting alloys. The coating process of calcium carbonate (CaCO3) has been done using Sodium trisilicate solution by sol-gel method. Foaming agent was pretreated by coating SiO2 passive layer on the surface of CaCO3. This coating aims to produce a more stable blowing agent so that the foaming process can produce a more uniform pore size. The microstructure of the SiO2 passive was observed using Scanning Electron Microscope (SEM) equipped by Energy Dispersive X-Ray Spectrometer (EDS) mapping. The results showed coating CaCO3 using sodium trisilicate was successfully done creating a passive layer of SiO2 on the surface of CaCO3. By the coating process, the thermal stability of coated CaCO3 increased compared to uncoated CaCO3.

Self-supported poly(methyl methacrylate-acrylonitrile-vinyl acetate)-based gel electrolyte for lithium ion battery

Energy Technology Data Exchange (ETDEWEB)

Liao, Y.H.; Zhou, D.Y.; Rao, M.M.; Cai, Z.P.; Liang, Y. [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Li, W.S.; Tan, C.L. [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Key Lab of Electrochemical Technology on Energy Storage and Power Generation in Guangdong Universities, Guangzhou 510006 (China)

2009-04-01

Self-supported gel polymer electrolyte (GPE) was prepared based on copolymer, poly(methyl methacrylate-acrylonitrile-vinyl acetate) (P(MMA-AN-VAc)). The copolymer P(MMA-AN-VAc) was synthesized by emulsion polymerization and the copolymer membrane was prepared through phase inversion. The structure and the performance of the copolymer, the membrane and the GPE were characterized by FTIR, NMR, SEM, XRD, DSC/TG, LSV, CA, and EIS. It is found that the copolymer was formed through the breaking of double bond C=C in each monomer. The membrane has low crystallinity and has low glass transition temperature, 39.1 C, its thermal stability is as high as 310 C, and its mechanical strength is improved compared with P(MMA-AN). The GPE is electrochemically stable up to 5.6 V (vs. Li/Li{sup +}) and its conductivity is 3.48 x 10{sup -3} S cm{sup -1} at ambient temperature. The lithium ion transference number in the GPE is 0.51 and the conductivity model of the GPE is found to obey the Vogel-Tamman-Fulcher (VTF) equation. (author)

Hydrophilic porous magnetic poly(GMA-MBAA-NVP) composite microspheres containing oxirane groups: An efficient carrier for immobilizing penicillin G acylase

Science.gov (United States)

Xue, Ping; Su, Weiguang; Gu, Yaohua; Liu, Haifeng; Wang, Julan

2015-03-01

Magnetic hydrophilic polymeric microspheres containing oxirane groups were prepared by inverse suspension polymerization of glycidyl methacrylate (GMA), N, N‧-methylene bisacrylamide (MBAA) and N-vinyl pyrrolidone (NVP) in the existence of formamide, which were denoted as magnetic poly(GMA-MBAA-NVP) microspheres. The magnetic poly(GMA-MBAA-NVP) microspheres were characterized by scanning electron microscopy (SEM), FT-IR spectroscopy, X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and so on. The results showed that poly(GMA-MBAA-NVP) microspheres possessed well spherical shape, narrow size distribution, abundant porous structure, reactive oxirane groups and superparamagnetic properties. Formamide used in the present work served as a modifier, a dispersant and a porogen to form final porous polymer microspheres. The penicillin G acylase (PGA) was covalently immobilized onto the magnetic microspheres through the reaction between the amino groups of enzyme and the oxirane groups on the microspheres for producing 6-aminopenicillanic acid (6-APA). The effects of GMA/NVP ratio and crosslink density on the activity of immobilized PGA were investigated. The highest apparent activity, enzyme loading and coupling yield of immobilized PGA were 821 IU/g, 65.3 mg/g and 42.3% respectively when the mass ratio of GMA/NVP was 1:1 and crosslink density was 60%. Compared with the free PGA, immobilized PGA showed a wider range of pH value and reaction temperature. The relative activity and reaction rate of immobilized PGA remained almost constant after 20 recycles. The magnetic poly(GMA-MBAA-NVP) microspheres would be very promising carriers for immobilizing enzymes in industrial application.

Iron halide mediated atom transfer radical polymerization of methyl methacrylate with N-Alkyl-2-pyridylmethanimine as the ligand

NARCIS (Netherlands)

Zhang, H.; Schubert, U.S.

2004-01-01

The controlled atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) catalyzed by iron halide/N-(n-hexyl)-2-pyridylmethanimine (NHPMI) is described. The ethyl 2-bromoisobutyrate (EBIB)-initiated ATRP with [MMA]0/[EBIB]0/[iron halide]0/[NHPMI]0 = 150/1/1/2 was better controlled in

76 FR 72617 - Animal Drugs, Feeds, and Related Products; Eprinomectin; N-Methyl-2-Pyrrolidone

Science.gov (United States)

2011-11-25

... (NMP), is a carcinogen. As required by section 512(d)(1)(I) of the Federal Food, Drug, and Cosmetic Act... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Parts 500, 522, and...-Pyrrolidone AGENCY: Food and Drug Administration, HHS. ACTION: Final rule. SUMMARY: The Food and Drug...

Grafting of HEMA onto dopamine coated stainless steel by 60Co-γ irradiation method

International Nuclear Information System (INIS)

Jin, Wanqin; Yang, Liming; Yang, Wei; Chen, Bin; Chen, Jie

2014-01-01

A novel method for grafting of 2-hydroxyethyl methacrylate (HEMA) onto the surface of stainless steel (SS) was explored by using 60 Co-γ irradiation. The surface of SS was modified by coating of dopamine before radiation grafting. The grafting reaction was performed in a simultaneous irradiation condition. The chemical structures change of the surface before and after grafting was demonstrated by Fourier transform infrared (FTIR) spectrometer. The hydrophilicity of the samples was determined by water contact angle measurement in the comparison of the stainless steel in the conditions of pristine, dopamine coated and HEMA grafted. Surface morphology of the samples was characterized by atomic force microscope (AFM) and scanning electron microscope (SEM). The corrosion resistance properties of the samples were evaluated by Tafel polarization curve. The hemocompatibility of the samples were tested by platelet adhesion assay. - Highlights: • Poly-HEMA was grafted onto the surface of SS by 60 Co-γ-ray irradiation. • Pristine SS was coated by dopamine to form a dense poly-dopamine film before radiation grafting. • The biocompatibility and hydrophility of SS were improved after the grafting of HEMA

properties of Cr(C,N) hard coatings deposited in Ar-C2H2-N2 plasma

International Nuclear Information System (INIS)

Macek, M.; Cekada, M.; Kek, D.; Panjan, P.

2002-01-01

Mechanical properties, microstructure and the average chemical composition of Cr(C,N) hard coatings deposited in Ar-C 2 H 2 -N 2 plasma strongly depends on the partial pressure of the reactive gases (N 2 , C 2 H 2 ) and on the type of the deposition equipment. In this study we report on the properties of Cr(C,N) hard coatings deposited by means of the triode ion plating in the BAI 730 apparatus and those prepared by sputter deposition in Balzers Sputron in the pressure range from 0.12 Pa (pure Ar) up to 0.35 Pa with different ratios (0-100%) between C 2 H 2 and N 2 . At first mechanical properties (microhardness and adhesion) of coatings were analyzed on the common way. Internal stress was measured by the radius of substrate curvature. Chemical composition of coatings was analyzed by means of AES while the Raman and XPS spectroscopy was used to determined the nature of carbon bonding in the Cr(C,N) films. Microstructure was determined by XRD as well as by means of TEM and TED. Chemical state of various elements in the coating has been studied by XPS. The ratio of the carbide bond (C-Cr) against the C-C and C-H bonds was calculated. The existence of the graphite phase in some Cr(C,N) coatings was confirmed by Raman spectroscopy. (Authors)

Hidroxyapatite Coating on CoCrMo Alloy Titanium Nitride Coated Using Biomimetic Method

International Nuclear Information System (INIS)

Charlena; Sukaryo, S.G.; Fajar, M.

2016-01-01

Bone implants is a way to cure broken bones which is being developed. The implants can be made of metals, ceramics and polymers. Metallic materials commonly used are titanium (Ti), stainless steel, and metal alloys. This study used Co-based alloys, i.e. CoCrMo coated with titanium nitride (TiN) which was then coated on hidroxyapatite (HAp). The HAp coating on the surface of CoCrMo alloy was done by biomimetic methods, first by soaking the metal alloys in simulated body fluid (SBF) solution for 18, 24, and 36 hours. The immersion in the SBF solution produced white coat on the surface of the metal alloy. The layers formed were analyzed by scanning electron microscope (SEM) and characterized by x-ray diffractometer (XRD). Based on the SEM results of 36 hours treatment, the morphology of apatite crystal formed fine grains. According to XRD result, there were HAp peaks at angles 2θ 31.86, 32.25, dan 39.48. However, there were also CaCO 3 peaks at angles 2θ 29.46, 36.04, and 46.79. It indicated the pure HAp is not yet formed. (paper)

Hidroxyapatite Coating on CoCrMo Alloy Titanium Nitride Coated Using Biomimetic Method

Science.gov (United States)

Charlena; Sukaryo, S. G.; Fajar, M.

2016-11-01

Bone implants is a way to cure broken bones which is being developed. The implants can be made of metals, ceramics and polymers. Metallic materials commonly used are titanium (Ti), stainless steel, and metal alloys. This study used Co-based alloys, i.e. CoCrMo coated with titanium nitride (TiN) which was then coated on hidroxyapatite (HAp). The HAp coating on the surface of CoCrMo alloy was done by biomimetic methods, first by soaking the metal alloys in simulated body fluid (SBF) solution for 18, 24, and 36 hours. The immersion in the SBF solution produced white coat on the surface of the metal alloy. The layers formed were analyzed by scanning electron microscope (SEM) and characterized by x-ray diffractometer (XRD). Based on the SEM results of 36 hours treatment, the morphology of apatite crystal formed fine grains. According to XRD result, there were HAp peaks at angles 2θ 31.86, 32.25, dan 39.48. However, there were also CaCO3 peaks at angles 2θ 29.46, 36.04, and 46.79. It indicated the pure HAp is not yet formed.

Preparation and characterization of glycidyl methacrylate organo bridges grafted mesoporous silica SBA-15 as ibuprofen and mesalamine carrier for controlled release

Energy Technology Data Exchange (ETDEWEB)

Rehman, Fozia, E-mail: fozia@iqm.unicamp.br [Institute of Chemistry, University of Campinas, UNICAMP, P.O. Box 6154, 13084-971 Campinas, SP (Brazil); Interdisciplinary Research Centre in Biomedical Materials (IRCBM), COMSATS Institute of Information Technology, Lahore (Pakistan); Rahim, Abdur [Interdisciplinary Research Centre in Biomedical Materials (IRCBM), COMSATS Institute of Information Technology, Lahore (Pakistan); Airoldi, Claudio; Volpe, Pedro L.O. [Institute of Chemistry, University of Campinas, UNICAMP, P.O. Box 6154, 13084-971 Campinas, SP (Brazil)

2016-02-01

Mesoporous silica SBA-15 was synthesized and functionalized with bridged polysilsesquioxane monomers obtained by the reaction of 3-aminopropyltriethoxy silane with glycidyl methacrylate in 2:1 ratio. The synthesized mesoporous silica materials were characterized by elemental analysis, infrared spectroscopy, nuclear magnetic resonance spectroscopy, nitrogen adsorption, X-ray diffraction, thermogravimetry and scanning electron microscopy. The nuclear magnetic resonance in the solid state is in agreement with the sequence of carbon distributed in the attached organic chains, as expected for organically functionalized mesoporous silica. After functionalization with organic bridges the BET surface area was reduced from 1311.80 to 494.2 m{sup 2} g{sup −1} and pore volume was reduced from 1.98 to 0.89 cm{sup 3} g{sup −1}, when compared to original precursor silica. Modification of the silica surface with organic bridges resulted in high loading capacity and controlled release of ibuprofen and mesalamine in biological fluids. The Korsmeyer–Peppas model better fits the release data indicating Fickian diffusion and zero order kinetics for synthesized mesoporous silica. The drug release rate from the modified silica was slow in simulated gastric fluid, (pH 1.2) where less than 10% of mesalamine and ibuprofen were released in initial 8 h, while comparatively high release rates were observed in simulated intestinal (pH 6.8) and simulated body fluids (pH 7.2). The preferential release of mesalamine at intestinal pH suggests that the modified silica could be a simple, efficient, inexpensive and convenient carrier for colon targeted drugs, such a mesalamine and also as a controlled drug release system. - Highlights: • Modified SBA-15 silica with long hydrophobic chains was evaluated as drug carrier. • This silica showed improved loading capacity and controlled release of ibuprofen. • Compared to gastric pH high release rate of mesalamine was observed at colonic pH. �

Preparation and characterization of glycidyl methacrylate organo bridges grafted mesoporous silica SBA-15 as ibuprofen and mesalamine carrier for controlled release

International Nuclear Information System (INIS)

Rehman, Fozia; Rahim, Abdur; Airoldi, Claudio; Volpe, Pedro L.O.

2016-01-01

Mesoporous silica SBA-15 was synthesized and functionalized with bridged polysilsesquioxane monomers obtained by the reaction of 3-aminopropyltriethoxy silane with glycidyl methacrylate in 2:1 ratio. The synthesized mesoporous silica materials were characterized by elemental analysis, infrared spectroscopy, nuclear magnetic resonance spectroscopy, nitrogen adsorption, X-ray diffraction, thermogravimetry and scanning electron microscopy. The nuclear magnetic resonance in the solid state is in agreement with the sequence of carbon distributed in the attached organic chains, as expected for organically functionalized mesoporous silica. After functionalization with organic bridges the BET surface area was reduced from 1311.80 to 494.2 m 2 g −1 and pore volume was reduced from 1.98 to 0.89 cm 3 g −1 , when compared to original precursor silica. Modification of the silica surface with organic bridges resulted in high loading capacity and controlled release of ibuprofen and mesalamine in biological fluids. The Korsmeyer–Peppas model better fits the release data indicating Fickian diffusion and zero order kinetics for synthesized mesoporous silica. The drug release rate from the modified silica was slow in simulated gastric fluid, (pH 1.2) where less than 10% of mesalamine and ibuprofen were released in initial 8 h, while comparatively high release rates were observed in simulated intestinal (pH 6.8) and simulated body fluids (pH 7.2). The preferential release of mesalamine at intestinal pH suggests that the modified silica could be a simple, efficient, inexpensive and convenient carrier for colon targeted drugs, such a mesalamine and also as a controlled drug release system. - Highlights: • Modified SBA-15 silica with long hydrophobic chains was evaluated as drug carrier. • This silica showed improved loading capacity and controlled release of ibuprofen. • Compared to gastric pH high release rate of mesalamine was observed at colonic pH. • Modified silica

Large scale solvothermal synthesis and a strategy to obtain stable Langmuir–Blodgett film of CoFe{sub 2}O{sub 4} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Thampi, Arya; Babu, Keerthi; Verma, Seema, E-mail: sa.verma@iiserpune.ac.in

2013-07-05

Highlights: • Large scale, monodisperse CoFe{sub 2}O{sub 4} nanoparticles by solvothermal route. • LB technique to obtain stable film of CoFe{sub 2}O{sub 4} nanoparticles over a large area. • Hydrophobicity of substrate was enhanced utilizing LB films of cadmium arachidate. • P–A isotherm and AFM cross sectional height profile analysis confirms stability. • Large scale organization of nanoparticles for surface pressure higher than 15 mN/m. -- Abstract: Nearly monodisperse oleic acid coated cobalt ferrite nanoparticles were synthesized in large scale by a simple solvothermal method utilizing N-methyl 2-Pyrrolidone (NMP) as a high boiling solvent. The magnetic oxide was further investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and vibrating sample magnetometer (VSM). Langmuir–Blodgett (LB) technique is discussed to obtain a 2D assembly of oleic acid coated CoFe{sub 2}O{sub 4} nanoparticles over a large area. We describe a method to obtain stable, condensed three layers of cadmium arachidate on a piranha treated glass substrate. The hydrophobic surface thus obtained was subsequently used for forming a stable monolayer of oleic acid stabilized cobalt ferrite nanoparticles at the air–water interface. The stability of the LB films at the air–water interface was studied by pressure–area isotherm curves and atomic force microscopy (AFM) cross sectional height profile analysis. 2D organization of the magnetic nanoparticles at different surface pressures was studied by TEM. Preparation of large area LB films of CoFe{sub 2}O{sub 4} nanoparticles is reported for a surface pressure more than 15 mN/m.

Poly(vinyl alcohol) hydrogel coatings with tunable surface exposure of hydroxyapatite

Science.gov (United States)

Moreau, David; Villain, Arthur; Ku, David N; Corté, Laurent

2014-01-01

Insufficient bone anchoring is a major limitation of artificial substitutes for connective osteoarticular tissues. The use of coatings containing osseoconductive ceramic particles is one of the actively explored strategies to improve osseointegration and strengthen the bone-implant interface for general tissue engineering. Our hypothesis is that hydroxyapatite (HA) particles can be coated robustly on specific assemblies of PVA hydrogel fibers for the potential anchoring of ligament replacements. A simple dip-coating method is described to produce composite coatings made of microscopic hydroxyapatite (HA) particles dispersed in a poly(vinyl alcohol) (PVA) matrix. The materials are compatible with the requirements for implant Good Manufacturing Practices. They are applied to coat bundles of PVA hydrogel fibers used for the development of ligament implants. By means of optical and electronic microscopy, we show that the coating thickness and surface state can be adjusted by varying the composition of the dipping solution. Quantitative analysis based on backscattered electron microscopy show that the exposure of HA at the coating surface can be tuned from 0 to over 55% by decreasing the weight ratio of PVA over HA from 0.4 to 0.1. Abrasion experiments simulating bone-implant contact illustrate how the coating cohesion and wear resistance increase by increasing the content of PVA relative to HA. Using pullout experiments, we find that these coatings adhere well to the fiber bundles and detach by propagation of a crack inside the coating. These results provide a guide to select coated implants for anchoring artificial ligaments. PMID:25482413

Poly(vinyl alcohol) hydrogel coatings with tunable surface exposure of hydroxyapatite.

Science.gov (United States)

Moreau, David; Villain, Arthur; Ku, David N; Corté, Laurent

2014-01-01

Insufficient bone anchoring is a major limitation of artificial substitutes for connective osteoarticular tissues. The use of coatings containing osseoconductive ceramic particles is one of the actively explored strategies to improve osseointegration and strengthen the bone-implant interface for general tissue engineering. Our hypothesis is that hydroxyapatite (HA) particles can be coated robustly on specific assemblies of PVA hydrogel fibers for the potential anchoring of ligament replacements. A simple dip-coating method is described to produce composite coatings made of microscopic hydroxyapatite (HA) particles dispersed in a poly(vinyl alcohol) (PVA) matrix. The materials are compatible with the requirements for implant Good Manufacturing Practices. They are applied to coat bundles of PVA hydrogel fibers used for the development of ligament implants. By means of optical and electronic microscopy, we show that the coating thickness and surface state can be adjusted by varying the composition of the dipping solution. Quantitative analysis based on backscattered electron microscopy show that the exposure of HA at the coating surface can be tuned from 0 to over 55% by decreasing the weight ratio of PVA over HA from 0.4 to 0.1. Abrasion experiments simulating bone-implant contact illustrate how the coating cohesion and wear resistance increase by increasing the content of PVA relative to HA. Using pullout experiments, we find that these coatings adhere well to the fiber bundles and detach by propagation of a crack inside the coating. These results provide a guide to select coated implants for anchoring artificial ligaments.

Characterization and taste masking evaluation of microparticles with cetirizine dihydrochloride and methacrylate-based copolymer obtained by spray drying

Directory of Open Access Journals (Sweden)

Amelian Aleksandra

2017-03-01

Full Text Available Taste of a pharmaceutical formulation is an important parameter for the effectiveness of pharmacotherapy. Cetirizine dihydrochloride (CET is a second-generation antihistamine that is commonly administered in allergy treatment. CET is characterized by extremely bitter taste and it is a great challenge to successfully mask its taste; therefore the goal of this work was to formulate and characterize the microparticles obtained by the spray drying method with CET and poly(butyl methacrylate-co-(2-dimethylaminoethyl methacrylate-co-methyl methacrylate 1:2:1 copolymer (Eudragit E PO as a barrier coating. Assessment of taste masking by the electronic tongue has revealed that designed formulations created an effective taste masking barrier. Taste masking effect was also confirmed by the in vivo model and the in vitro release profile of CET. Obtained data have shown that microparticles with a drug/polymer ratio (0.5:1 are promising CET carriers with efficient taste masking potential and might be further used in designing orodispersible dosage forms with CET.

Allylthioketone Mediated Free Radical Polymerization of Methacrylates

Directory of Open Access Journals (Sweden)

Feng Zhong

2017-11-01

Full Text Available By combination of high trapping free radical efficiency of the thioketone and resonance of the allylic radical, a new type of mediating agent, 1,3,3-triphenylprop-2-ene-1-thione (TPPT has been successfully synthesized, and then is used to study controlled free radical polymerization of methacrylates. Very stable TPPT radicals at the end of poly(methyl methacrylate (PMMA are detected in the polymerization of MMA using TPPT and AIBN as the control agent and initiator. The MALDI-TOF MS spectra are used to identify terminal groups of the resultant poly(glycidyl methacrylate (PGMA, and major component of the obtained polymer has the structure, (CH32(CNC-PGMA-C7H9O3. Chain extension reaction tests ascertain formation of the dead polymers during the polymer storage and purification process of the polymers. Owing to very slow fragmentation reaction of the TPPT-terminated polymethacrylate radical and addition reaction of this radical with a primary radical, the growing chain radicals are difficult to be regenerated, leading to an unobvious change of the molecular weight with monomer conversion. The molecular weights of polymers can be controlled by the ratios of monomer/initiator and TPPT/initiator. However, the first order kinetics of the polymerization and the polymers with narrow polydispersity are obtained, and these phenomena are discussed. This study provides useful information on how to design a better controlling agent.

Williamson alkylation approach to the synthesis of poly(alkyl vinyl ether) copolymers

International Nuclear Information System (INIS)

Markova, D.; Christova, D.; Velichkova, R.

2008-01-01

A method for synthesis of poly(alkyl vinyl ether-co-vinyl alcohol) copolymers was developed based on the Williamson's alkylation of poly(vinyl acetate) (PVAc) with alkyl iodides. The influence of the alkylating agent and the reaction conditions on the efficiency of the modification reaction was investigated. The copolymers obtained were characterized by means of 1 H NMR and GPC. It was proved that by applying the proposed method copolymers of different composition and properties containing methyl vinyl ether, ethyl vinyl ether as well as n-butyl vinyl ether units could be prepared. Poly(methyl vinyl ether-co-vinyl alcohol)s of high degree of methylation exhibit sharp temperature response at 38-39 deg C in aqueous solution typical of the so-called smart polymers. (authors)

Spin-Coating and Characterization of Multiferroic MFe2O4 (M=Co, Ni) / BaTiO3 Bilayers

Science.gov (United States)

Quandt, Norman; Roth, Robert; Syrowatka, Frank; Steimecke, Matthias; Ebbinghaus, Stefan G.

2016-01-01

Bilayer films of MFe2O4 (M=Co, Ni) and BaTiO3 were prepared by spin coating of N,N-dimethylformamide/acetic acid solutions on platinum coated silicon wafers. Five coating steps were applied to get the desired thickness of 150 nm for both the ferrite and perovskite layer. XRD, IR and Raman spectroscopy revealed the formation of phase-pure ferrite spinels and BaTiO3. Smooth surfaces with roughnesses in the order of 3 to 5 nm were found in AFM investigations. Saturation magnetization of 347 emu cm-3 for the CoFe2O4/BaTiO3 and 188 emu cm-3 for the NiFe2O4/BaTiO3 bilayer, respectively were found. For the CoFe2O4/BaTiO3 bilayer a strong magnetic anisotropy was observed with coercivity fields of 5.1 kOe and 3.3 kOe (applied magnetic field perpendicular and parallel to film surface), while for the NiFe2O4/BaTiO3 bilayer this effect is less pronounced. Saturated polarization hysteresis loops prove the presence of ferroelectricity in both systems.

TEMPLATE POLYMERIZATION OF N-VINYLIMIDAZOLE ALONG POLY(METHACRYLIC ACID) IN WATER .2. KINETICS OF THE TEMPLATE POLYMERIZATION

NARCIS (Netherlands)

VANDEGRAMPEL, HT; TAN, YY; CHALLA, G

1991-01-01

The template polymerization of N-vinylimidazole (VIm) along poly(methacrylic acid) (PMAA) in water at 50-degrees-C with 2,2'-azobis(2-amidinopropane).2HCl (AAP) as initiator was studied by using variable initiator and monomer concentrations at constant [PMAA]/[VIm]0. From the order in [VIm] it was

Design of poly(vinylidene fluoride)-g-p(hydroxyethyl methacrylate-co-N-isopropylacrylamide) membrane via surface modification for enhanced fouling resistance and release property

International Nuclear Information System (INIS)

Zhao, Guili; Chen, Wei Ning

2017-01-01

Highlights: • PVDF modified membranes were designed by grafting PNIPAAm, PHEMA and their copolymer. • Fouling resistance and release property of membrane were both improved after modification. • Bacterial attachment and detachment were investigated to evaluate fouling release property. • Improvement of the antifouling property was justified by surface property analysis. • The copolymer modified membrane exhibited higher performance to release foulant. - Abstract: Thermo-sensitive polymer poly(N-isopropylacrylamide) (PNIPAAm), hydrophilic polymer poly(hydroxyethyl methacrylate) (PHEMA) and copolymer p(hydroxyethyl methacrylate-co-N-isopropylacrylamide) [P(HEMA-co-NIPAAm)] were synthesized onto poly(vinylidene fluoride) (PVDF) membrane via atom transfer radical polymerization (ATRP) in order to improve not only fouling resistance but also fouling release property. The physicochemical properties of membranes including hydrophilicity, morphology and roughness were examined by contact angle analyzer, scanning electron microscopy (SEM), and atomic force microscopy (AFM), respectively. The antifouling property of membranes was improved remarkably after surface modification according to protein and bacterial adhesion testing, and filtration experiment. Minimum protein adsorption and bacterial adhesion were both obtained on PVDF-g-P(HEMA-co-NIPAAm) membrane, with reduction by 44% and 71% respectively compared to the pristine membrane. The minimum bacterial cells after detachment at 25 °C were observed on the PVDF-g-P(HEMA-co-NIPAAm) membrane with the detachment rate of 77%, indicating high fouling release property. The filtration testing indicated that the copolymer modified membrane exhibited high resistance to protein fouling and the foulant on the surface was released and removed easily by washing, suggesting high fouling release and easy-cleaning capacity. This study provides useful insight in the combined “fouling resistance” and “fouling release�

Design of poly(vinylidene fluoride)-g-p(hydroxyethyl methacrylate-co-N-isopropylacrylamide) membrane via surface modification for enhanced fouling resistance and release property

Energy Technology Data Exchange (ETDEWEB)

Zhao, Guili [Nanyang Environment and Water Research Institute, Interdisciplinary Graduate School, Nanyang Technological University, 1 Cleantech Loop, Singapore 637141 (Singapore); Advanced Environmental Biotechnology Centre, Nanyang Environment and Water Research Institute, Nanyang Technological University, 1 Cleantech Loop, Singapore 637141 (Singapore); School of Chemical and Biomedical Engineering, Nanyang Technological University, 62 Nanyang Drive, Singapore 637459 (Singapore); Chen, Wei Ning, E-mail: WNChen@ntu.edu.sg [School of Chemical and Biomedical Engineering, Nanyang Technological University, 62 Nanyang Drive, Singapore 637459 (Singapore)

2017-03-15

Highlights: • PVDF modified membranes were designed by grafting PNIPAAm, PHEMA and their copolymer. • Fouling resistance and release property of membrane were both improved after modification. • Bacterial attachment and detachment were investigated to evaluate fouling release property. • Improvement of the antifouling property was justified by surface property analysis. • The copolymer modified membrane exhibited higher performance to release foulant. - Abstract: Thermo-sensitive polymer poly(N-isopropylacrylamide) (PNIPAAm), hydrophilic polymer poly(hydroxyethyl methacrylate) (PHEMA) and copolymer p(hydroxyethyl methacrylate-co-N-isopropylacrylamide) [P(HEMA-co-NIPAAm)] were synthesized onto poly(vinylidene fluoride) (PVDF) membrane via atom transfer radical polymerization (ATRP) in order to improve not only fouling resistance but also fouling release property. The physicochemical properties of membranes including hydrophilicity, morphology and roughness were examined by contact angle analyzer, scanning electron microscopy (SEM), and atomic force microscopy (AFM), respectively. The antifouling property of membranes was improved remarkably after surface modification according to protein and bacterial adhesion testing, and filtration experiment. Minimum protein adsorption and bacterial adhesion were both obtained on PVDF-g-P(HEMA-co-NIPAAm) membrane, with reduction by 44% and 71% respectively compared to the pristine membrane. The minimum bacterial cells after detachment at 25 °C were observed on the PVDF-g-P(HEMA-co-NIPAAm) membrane with the detachment rate of 77%, indicating high fouling release property. The filtration testing indicated that the copolymer modified membrane exhibited high resistance to protein fouling and the foulant on the surface was released and removed easily by washing, suggesting high fouling release and easy-cleaning capacity. This study provides useful insight in the combined “fouling resistance” and “fouling release�

Preparation of poly (vinyl alcohol) membranes grafted with n-vinyl pyridine/ acrylic acid binary monomers

International Nuclear Information System (INIS)

Ajji, A.; Ali, A.

2014-03-01

Poly(vinyl alcohol) films were grafted with two monomers using gamma radiation, acrylic acid and N-vinyl pyridine. The influence of different parameters on the grafting yield was investigated as: the comonomer concentration and composition, and irradiation dose. The suitable conditions of the process had been determined to prepare PVA membranes have both properties of the two monomers, acrylic acid and vinyl pyridine as comonomer concentration and composition, and irradiation dose. Some properties of the membranes had been investigated as maximum swelling and grafting. Also the ability of the grafted films to adsorb some heavy metals and dyes was elaborated and discussed.(author)

NIOSH Manual of Analytical Methods (third edition). Fourth supplement

Energy Technology Data Exchange (ETDEWEB)

1990-08-15

The NIOSH Manual of Analytical Methods, 3rd edition, was updated for the following chemicals: allyl-glycidyl-ether, 2-aminopyridine, aspartame, bromine, chlorine, n-butylamine, n-butyl-glycidyl-ether, carbon-dioxide, carbon-monoxide, chlorinated-camphene, chloroacetaldehyde, p-chlorophenol, crotonaldehyde, 1,1-dimethylhydrazine, dinitro-o-cresol, ethyl-acetate, ethyl-formate, ethylenimine, sodium-fluoride, hydrogen-fluoride, cryolite, sodium-hexafluoroaluminate, formic-acid, hexachlorobutadiene, hydrogen-cyanide, hydrogen-sulfide, isopropyl-acetate, isopropyl-ether, isopropyl-glycidyl-ether, lead, lead-oxide, maleic-anhydride, methyl-acetate, methyl-acrylate, methyl-tert-butyl ether, methyl-cellosolve-acetate, methylcyclohexanol, 4,4'-methylenedianiline, monomethylaniline, monomethylhydrazine, nitric-oxide, p-nitroaniline, phenyl-ether, phenyl-ether-biphenyl mixture, phenyl-glycidyl-ether, phenylhydrazine, phosphine, ronnel, sulfuryl-fluoride, talc, tributyl-phosphate, 1,1,2-trichloro-1,2,2-trifluoroethane, trimellitic-anhydride, triorthocresyl-phosphate, triphenyl-phosphate, and vinyl-acetate.

1,4-Di(2-butoxycarbonyl-trans-vinyl-2,5-dimethoxybenzene

Directory of Open Access Journals (Sweden)

William A. Molano

2015-11-01

Full Text Available The title compound 1,4-di(2-butoxycarbonyl-trans-vinyl-2,5-dimethoxybenzene was synthesized in 94% yield through the Heck reaction between 2,5-diiodo-1,4-dimethoxybenzene and n-butyl acrylate, using bis(dibenzylideneacetone palladium(0 as homogeneous catalyst.

Radiation synthesis and characterization of zinc phthalocyanine composite based on 2-hydroxyethyl methacrylate/methyl methacrylate copolymer

International Nuclear Information System (INIS)

Abdel Ghaffar, A.M.; Youssef, Tamer E.; Mohamed, Hanan H.

2016-01-01

The synthesis and characterization of new 2-hydroxyethyl methacrylate-co-methyl methacrylate/zinc phthalocyanine composite Poly(HEMA/MMA/ZnPc) is described for the first time in this study. The aim of this research is to present possibility of radiation synthesis of the newly zinc phthalocyanine composites as potential candidates for wide range of applications. Gel (%) and swelling for Poly(hydroxyethyl methacrylate) Poly(HEMA) and the based Poly(hydroxyethyl methacrylate/methyl methacrylate) copolymer Poly(HEMA/MMA) with different composition 100/0, 95/5, 90/10 and 80/20 wt % were evaluated. It was found that Poly(HEMA/MMA) copolymer with composition 95/5 wt % characterized by its high swelling property at pH 7.4. The prepared composites I and II Poly(HEMA/MMA/ZnPc) with composition (95/5/1 wt%) and (95/5/1.5 wt%) respectively have been characterized by FTIR and TGA. The effect of gamma irradiation on the chemical properties of composite I was described. It is observed that the Zinc phthalocyanine with low concentration 1 wt % enhance chemical, thermal properties and stabilization against gamma radiation of the prepared composite I. - Highlights: • The preparation of Poly(HEMA/MMA/ZnPc) by radiation forming modified composites. • The low concentration of ZcPc (1 or 1.5 wt %) lead to form outstanding properties. • These composites are a potential candidate for wide range of applications.

Radiation synthesis and characterization of zinc phthalocyanine composite based on 2-hydroxyethyl methacrylate/methyl methacrylate copolymer

Energy Technology Data Exchange (ETDEWEB)

Abdel Ghaffar, A.M., E-mail: am_abdelghaffar@yahoo.com [Radiation Research of Polymer Chemistry Department, Industrial Irradiation Division, National Center for Radiation Research and Technology, Atomic Energy Authority P.O. Box 29, Nasr City, Cairo (Egypt); Youssef, Tamer E. [Applied Organic Chemistry Department, Chemical Industries Research Division, National Research Center, Dokki, Cairo, 12622 (Egypt); Chemical and Materials Engineering Department, Faculty of Engineering, King Abdulaziz University, P.O. Box 80204, Jeddah, 21589 (Saudi Arabia); Mohamed, Hanan H. [Chemistry Department, Faculty of Science, Helwan University, Ain Helwan, Cairo (Egypt)

2016-08-01

The synthesis and characterization of new 2-hydroxyethyl methacrylate-co-methyl methacrylate/zinc phthalocyanine composite Poly(HEMA/MMA/ZnPc) is described for the first time in this study. The aim of this research is to present possibility of radiation synthesis of the newly zinc phthalocyanine composites as potential candidates for wide range of applications. Gel (%) and swelling for Poly(hydroxyethyl methacrylate) Poly(HEMA) and the based Poly(hydroxyethyl methacrylate/methyl methacrylate) copolymer Poly(HEMA/MMA) with different composition 100/0, 95/5, 90/10 and 80/20 wt % were evaluated. It was found that Poly(HEMA/MMA) copolymer with composition 95/5 wt % characterized by its high swelling property at pH 7.4. The prepared composites I and II Poly(HEMA/MMA/ZnPc) with composition (95/5/1 wt%) and (95/5/1.5 wt%) respectively have been characterized by FTIR and TGA. The effect of gamma irradiation on the chemical properties of composite I was described. It is observed that the Zinc phthalocyanine with low concentration 1 wt % enhance chemical, thermal properties and stabilization against gamma radiation of the prepared composite I. - Highlights: • The preparation of Poly(HEMA/MMA/ZnPc) by radiation forming modified composites. • The low concentration of ZcPc (1 or 1.5 wt %) lead to form outstanding properties. • These composites are a potential candidate for wide range of applications.

Quaternized poly(methyl methacrylate-co-butyl acrylate-co-vinylbenzyl chloride) membrane for alkaline fuel cells

Energy Technology Data Exchange (ETDEWEB)

Luo, Yanting; Guo, Juchen; Wang, Chunsheng [Department of Chemical and Biomolecular Engineering, University of Maryland, College Park, MD 20742 (United States); Chu, Deryn [Sensors and Electron Device Directorate, U.S. Army Research Laboratory, Adelphi, MD 20783 (United States)

2010-06-15

Instead of modification of pre-existing polymers, a new route of preparation of polyelectrolyte OH{sup -} conductive membranes via copolymerization of selected functional monomers was reported in this study. A random copolymer of poly(methyl methacrylate-co-butyl acrylate-co-vinylbenzyl chloride) was synthesized via copolymerization, which was followed by quaternization and membrane casting. The intrinsic OH{sup -} conductivity of the free-standing polyelectrolyte membranes can reach 8.2 x 10{sup -3} S cm{sup -1} at 80 C. The alkaline fuel cells using copolymer polyelectrolytes demonstrated the feasibility of the preparation concept of these membranes. (author)

Comparative studies with n-methyl-2-pyrrolidone and furfural as solvents for extraction of lube distillates

Energy Technology Data Exchange (ETDEWEB)

Krishna, R.; Singh, H.; Kishore, K.; Choudhary, G.S.; Kaushik, R.S.

Solvent extraction of spindle raw lube distillate from Oman crude using n-methyl pyrrolidone (NMP) containing 1.5 wt.% water has been studied using a six-stage all-glass mixer-settler. Results of three operating temperatures with NMP are reported. A 65-55/sup 0/C extraction temperature appears to be most appropriate for this stock. Data obtained at this temperature have been compared with those for furfural on the basis of phase boundary curves, extraction and lube refining indices and selectivity. Comparison of the results shows NMP to be more selective as far as raffinate yield is concerned. It requires lower operating solvent-to-feed ratios and lower temperatures. 14 refs.

Supercritical CO2 drying of poly(methyl methacrylate) photoresist for deep x-ray lithography: a brief note

Science.gov (United States)

Shukla, Rahul; Abhinandan, Lala; Sharma, Shivdutt

2017-07-01

Poly(methyl methacrylate) (PMMA) is an extensively used positive photoresist for deep x-ray lithography. The post-development release of the microstructures of PMMA becomes very critical for high aspect ratio fragile and freestanding microstructures. Release of high aspect ratio comb-drive microstructure of PMMA made by one-step x-ray lithography (OXL) is studied. The effect of low-surface tension Isopropyl alcohol (IPA) over water is investigated for release of the high aspect ratio microstructures using conventional and supercritical (SC) CO2 drying. The results of conventional drying are also compared for the samples released or dried in both in-house developed and commercial SC CO2 dryer. It is found that in all cases the microstructures of PMMA are permanently deformed and damaged while using SC CO2 for drying. For free-standing high aspect ratio microstructures of PMMA made by OXL, it is advised to use low-surface tension IPA over DI water. However, this brings a limitation on the design of the microstructure.

A Polymethyl Methacrylate-Based Acrylic Dental Resin Surface Bound with a Photoreactive Polymer Inhibits Accumulation of Bacterial Plaque.

Science.gov (United States)

Fukunishi, Miya; Inoue, Yuuki; Morisaki, Hirobumi; Kuwata, Hirotaka; Ishihara, Kazuhiko; Baba, Kazuyoshi

The aim of this study was to examine the ability of a poly(2-methacryloyloxyethyl phosphorylcholine-co-n-butylmethacrylate-co-2-methacryloyloxyethyloxy-p-azidobenzoate) (PMBPAz) coating on polymethyl methacrylate (PMMA)-based dental resin to inhibit bacterial plaque formation, as well as the polymer's durability against water soaking and chemical exposure. Successful application of PMBPAz on PMMA surfaces was confirmed by x-ray photoelectron spectroscopy (XPS) and measuring the static air contact angle in water. The anti-adhesive effects to bacterial plaque were evaluated using Streptococcus mutans biofilm formation assay. The mechanical and chemical durabilities of the PMBPAz coating on the PMMA surfaces were examined using soaking and immersion tests, respectively. XPS signals for phosphorus and nitrogen atoms and hydrophilic status on PMMA surfaces treated with PMBPAz were observed, indicating the presence of the polymer on the substrates. The treated PMMA surfaces showed significant inhibition of S mutans biofilm formation compared to untreated surfaces. The PMBPAz coating was preserved after water soaking and chemical exposure. In addition, water soaking did not decrease the ability of treated PMMA to inhibit biofilm formation compared to treated PMMA specimens not subjected to water soaking. This study suggests that PMBPAz coating may represent a useful modification to PMMA surfaces for inhibiting denture plaque accumulation.

Halloysite nanotubes grafted hyperbranched (co)polymers via surface-initiated self-condensing vinyl (co)polymerization

International Nuclear Information System (INIS)

Mu Bin; Zhao Mingfei; Liu Peng

2008-01-01

Halloysite nanotubes (HNTs) grafted hyperbranched polymers were prepared by the self-condensing vinyl polymerization (SCVP) of 2-((bromoacetyl)oxy)ethyl acrylate (BAEA) and the self-condensing vinyl copolymerization of n-butyl acrylate (BA) and BAEA with BAEA as inimer (AB*) respectively, from the surfaces of the 2-bromoisobutyric acid modified halloysite nanotubes (HNTs-Br) via atom transfer radical polymerization (ATRP) technique. The halloysite nanotubes grafted hyperbranched polymer (HNTs-HP) and the halloysite nanotubes grafted hyperbranched copolymer (HNTs-HCP) were characterized by elemental analysis (EA), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and transmission electron microscope (TEM). The grafted hyperbranched polymers were characterized with Nuclear magnetic resonance (NMR) and the molecular ratio between the inimer AB* and BA in the grafted hyperbranched copolymers was found to be 3:2, calculated from the TGA and EA results

Halloysite nanotubes grafted hyperbranched (co)polymers via surface-initiated self-condensing vinyl (co)polymerization

Energy Technology Data Exchange (ETDEWEB)

Mu Bin; Zhao Mingfei; Liu Peng [Lanzhou University, State Key Laboratory of Applied Organic Chemistry and Institute of Polymer Science and Engineering, College of Chemistry and Chemical Engineering (China)], E-mail: pliu@lzu.edu.cn

2008-05-15

Halloysite nanotubes (HNTs) grafted hyperbranched polymers were prepared by the self-condensing vinyl polymerization (SCVP) of 2-((bromoacetyl)oxy)ethyl acrylate (BAEA) and the self-condensing vinyl copolymerization of n-butyl acrylate (BA) and BAEA with BAEA as inimer (AB*) respectively, from the surfaces of the 2-bromoisobutyric acid modified halloysite nanotubes (HNTs-Br) via atom transfer radical polymerization (ATRP) technique. The halloysite nanotubes grafted hyperbranched polymer (HNTs-HP) and the halloysite nanotubes grafted hyperbranched copolymer (HNTs-HCP) were characterized by elemental analysis (EA), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and transmission electron microscope (TEM). The grafted hyperbranched polymers were characterized with Nuclear magnetic resonance (NMR) and the molecular ratio between the inimer AB* and BA in the grafted hyperbranched copolymers was found to be 3:2, calculated from the TGA and EA results.

Investigation of nanocarriers and excipients for preparation of nanoembedded microparticles

DEFF Research Database (Denmark)

Wang, Yingya; Beck-broichsitter, Moritz; Yang, Mingshi

2017-01-01

polymer nanocarriers (poly(lactide-co-glycolide), poly(styrene), chitosan and dendrimers) were used for preparing NEMs by spray-drying. Further, distinct matrix excipients were investigated including sugars (i.e., trehalose, sucrose, mannitol) and polymers (poly(vinyl pyrrolidone) and poly(ethylene glycol...... (trehalose, sucrose, poly(vinyl pyrrolidone)) are superior to spray-dried crystalline excipients (mannitol, poly(ethylene glycol)) for stabilizing NEMs. It is therefore important to select an appropriate excipient for stabilization of a given nanoparticle system and identify a suitable level...

Methacrylate monolithic columns functionalized with epinephrine for capillary electrochromatography applications.

Science.gov (United States)

Carrasco-Correa, Enrique Javier; Ramis-Ramos, Guillermo; Herrero-Martínez, José Manuel

2013-07-12

Epinephrine-bonded polymeric monoliths for capillary electrochromatography (CEC) were developed by nucleophilic substitution reaction of epoxide groups of poly(glycidyl-methacrylate-co-ethylenedimethacrylate) (poly(GMA-co-EDMA)) monoliths using epinephrine as nucleophilic reagent. The ring opening reaction under dynamic conditions was optimized. Successful chemical modification of the monolith surface was ascertained by in situ Raman spectroscopy characterization. In addition, the amount of epinephrine groups that was bound to the monolith surface was evaluated by oxidation of the catechol groups with Ce(IV), followed by spectrophotometric measurement of unreacted Ce(IV). About 9% of all theoretical epoxide groups of the parent monolith were bonded to epinephrine. The chromatographic behavior of the epinephrine-bonded monolith in CEC conditions was assessed with test mixtures of alkyl benzenes, aniline derivatives and substituted phenols. In comparison to the poly(GMA-co-EDMA) monoliths, the epinephrine-bonded monoliths exhibited a much higher retention and slight differences in selectivity. The epinephrine-bonded monolith was further modified by oxidation with a Ce(IV) solution and compared with the epinephrine-bonded monoliths. The resulting monolithic stationary phases were evaluated in terms of reproducibility, giving RSD values below 9% in the parameters investigated. Copyright © 2013 Elsevier B.V. All rights reserved.

Reactive compatibilization of ethylene-co-vinyl acetate/starch blends

NARCIS (Netherlands)

Ma, P.; Hristova - Bogaerds, D.G.; Schmit, P.; Goossens, J.G.P.; Lemstra, P.J.

2012-01-01

The dispersion of starch as a filler in hydrophobic ethylene-co-vinyl acetate (EVA) rubber is an issue. To obtain a fine dispersion of starch in EVA rubber, EVA/starch blends were prepared by reactive extrusion in the pres- ence of maleic anhydride (MA), benzoyl peroxide (BPO), and glycerol. MA,

Cd(II) and Zn(II) Complexes Containing N,N'-Bidentate N-(Pyridin-2-ylmethylene)cyclopentanamine: Synthesis, Characterisation and Methyl Methacrylate Polymerisation

Energy Technology Data Exchange (ETDEWEB)

Song, Yu Jin; Lee, Ha Jun; Lee, Hyo Sun [Kyungpook National University, Daeju (Korea, Republic of)

2014-09-15

The reaction between [CdBr{sub 2}·4H{sub 2}O] and anhydrous [ZnCl{sub 2}] with N,N'-bidentate N-(pyridin-2-ylmethylene)- cyclopentanamine (impy) in ethanol yields dimeric [(impy)Cd(μ-Br)Br]2 and monomeric [(impy)ZnCl{sub 2}] complexes, respectively. The X-ray crystal structure of Cd(II) and Zn(II) complexes revealed that the cadmium atom in [(impy)Cd(μ-Br)Br]2 and zinc in [(impy)ZnCl{sub 2}] formed a distorted trigonal–bipyramidal and tetrahedral geometry, respectively. Both complexes showed moderate catalytic activity for the polymerisation of methyl methacrylate (MMA) in the presence of modified methylaluminoxane (MMAO), with polymethylmethacrylate (PMMA) syndiotacticity of about 0.70.

Ionizing radiation method for forming acrylic pressure sensitive adhesives and coated substrates

International Nuclear Information System (INIS)

Dowbenko, R.; Christenson, R.M.

1975-01-01

Pressure-sensitive adhesive having improved adhesive properties are formed by subjecting a mixture comprising a monomer selected from the group consisting of alkyl acrylates, hydroxyalkyl acrylates, alkoxyalkyl acrylates, cyanoalkyl acrylates, alkyl methacrylates, hydroxyalkyl methacrylates, alkoxyalkyl methacrylates, cyanoalkyl methacrylates, N-alkoxymethylacrylamides, and N-alkoxymethylmethacrylamides, and a homopolymer or copolymer selected from the group consisting of polymers of alkyl acrylates, hydroxyalkyl acrylates, alkoxyalkyl acrylates, cyanoalkyl acrylates, alkyl methacrylates, hydroxyalkyl methacrylates, alkoxyalkyl methacrylates, cyanoalkyl methacrylates, acrylamide, methacrylamide, N-(substituted alkyl) acrylamides, N-(substituted alkyl) methacrylamides, alkyl acrylamides, alkyl methacrylamides, and N-alkoxymethylacrylamides and N-alkoxymethylmethacrylamides to ionizing irradiation. The adhesive material finds utility as binding resins in laminates, coatings on substrates, and as film adhesives. (U.S.)

Interaction between poly(vinyl pyridine) and poly(2,6-dimethyl-1,4-phenylene oxide) : A copolymer blend miscibility study

NARCIS (Netherlands)

de Wit, Joost; van Ekenstein, Gert Alberda; ten Brinke, Gerrit

2007-01-01

The phase behavior of blends of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) with random copolymers of styrene and 2-vinyl pyridine, Poly(S-co-2VP), as well as with random copolymers of styrene and 4-vinyl pyridine, Poly(S-co-4VP), has been investigated in order to estimate the values of the

Microstructure and properties of duplex (Ti:N)-DLC/MAO coating on magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Yang, Wei; Ke, Peiling [Ningbo Key Laboratory of Marine Protection Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Fang, Yong [Sir Run Run Shaw Hospital, School of Medicine, Zhe Jiang University, Zhejiang 310016 (China); Zheng, He [Ningbo Key Laboratory of Marine Protection Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Wang, Aiying, E-mail: aywang@nimte.ac.cn [Ningbo Key Laboratory of Marine Protection Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)

2013-04-01

Ti and N co-doped diamond-like carbon ((Ti:N)-DLC) film was deposited on the MAO coated substrate using a hybrid beam deposition system, which consists of a DC magnetron sputtering of Ti target and a linear ion source (LIS) with C{sub 2}H{sub 2} and N{sub 2} precursor gas. The microstructure and properties of the duplex (Ti:N)-DLC/MAO coating were investigated. Results indicate that the (Ti:N)-DLC top film with TiN crystalline phase was formed. Ti and N co-doping resulted in the increasing I{sub D}/I{sub G} ratio. The significant improvement in the wear and corrosion resistance of duplex (Ti:N)-DLC/MAO coating was mainly attributed to the increased binding strength, lubrication characteristics and chemical inertness of (Ti:N)-DLC top film. The superior low-friction and anti-corrosion properties of duplex (Ti:N)-DLC/MAO coating make it a good candidate as protective coating on magnesium alloy.

A polyether glycol derived from cashew nutshell as a kinetic inhibitor for methane hydrate formation

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Jorge Cesar; Esteves, Pierre M., E-mail: pesteves@iq.ufrj.br [Instituto de Quimica, Universidade Federal do Rio de Janeiro, Rio de Janeiro, RJ (Brazil); Teixeira, Adriana [Centro de Pesquisa e Desenvolvimento Leopoldo Americo Miguez de Mello, PETROBRAS, Rio de Janeiro, RJ (Brazil)

2012-07-01

The polyether glycol derived from cashew nutshell liquid inhibited the formation of methane hydrate. The polymer proved to be more efficient than the polyvinyl pyrrolidone-poly(N-vinyl) caprolactam (PVP-PVCap) co-polymer under tested conditions (CH{sub 4}, 1470 psi and 4 degree C), being the latter one of the best commercially available hydrate inhibitors. (author)

Effect of Cross-Linking on the Mechanical and Thermal Properties of Poly(amidoamine) Dendrimer/Poly(vinyl alcohol) Hybrid Membranes for CO2 Separation.

Science.gov (United States)

Duan, Shuhong; Kai, Teruhiko; Saito, Takashi; Yamazaki, Kota; Ikeda, Kenichi

2014-04-08

Poly(amidoamine) (PAMAM) dendrimers were incorporated into cross-linked poly(vinyl alcohol) (PVA) matrix to improve carbon dioxide (CO2) separation performance at elevated pressures. In our previous studies, PAMAM/PVA hybrid membranes showed high CO2 separation properties from CO2/H2 mixed gases. In this study, three types of organic Ti metal compounds were selected as PVA cross-linkers that were used to prepare PAMAM/cross-linked PVA hybrid membranes. Characterization of the PAMAM/cross-linked PVA hybrid membranes was conducted using nanoindentation and thermogravimetric analyses. The effects of the cross-linker and CO2 partial pressure in the feed gas on CO2 separation performance were discussed. H2O and CO2 sorption of the PAMAM/PVA hybrid membranes were investigated to explain the obtained CO2 separation efficiencies.

Improvement of structural and electrochemical properties of commercial LiCoO2 by coating with LaF3

International Nuclear Information System (INIS)

Yang Zhanxu; Qiao Qingdong; Yang Wensheng

2011-01-01

Highlights: → LaF 3 has been introduced as a new coating material for the LiCoO 2 cathode. → The LaF 3 -coated LiCoO 2 showed an excellent overcharge tolerance and structure stability. → The thermal stability of the LaF 3 -coated cathode is significantly enhanced. Therefore, LaF 3 is a probably potential coating material. - Abstract: Commercial LiCoO 2 has been modified with LaF 3 as a new coating material. The surface modified materials were characterized by X-ray diffraction (XRD), transmission electronic microscopy (TEM), field emission scanning electron microscopy (FE-SEM), auger electron spectroscopy (AES) and galvanostatic charge-discharge cycling. The LaF 3 -coated LiCoO 2 had an initial discharge specific capacity of 177.4 mAh g -1 within the potential ranges 2.75-4.5 V (vs. Li/Li + ), and showed a good capacity retention of 90.9% after 50 cycles. It was found that the overcharge tolerance of the coated cathode was significantly better than that of the pristine LiCoO 2 under the same conditions - the capacity retention of the pristine LiCoO 2 was 62.3% after 50 cycles. The improvement could be attributed to the LaF 3 coating layer that hinders interaction between LiCoO 2 and electrolyte and stabilizes the structure of LiCoO 2 . Moreover, DSC showed that the coated LiCoO 2 had a higher thermal stability than the pristine LiCoO 2 .

Photoinitiated chemical vapor deposition of cytocompatible poly(2-hydroxyethyl methacrylate) films.

Science.gov (United States)

McMahon, Brian J; Pfluger, Courtney A; Sun, Bing; Ziemer, Katherine S; Burkey, Daniel D; Carrier, Rebecca L

2014-07-01

Poly(2-hydroxyethyl methacrylate) (pHEMA) is a widely utilized biomaterial due to lack of toxicity and suitable mechanical properties; conformal thin pHEMA films produced via chemical vapor deposition (CVD) would thus have broad biomedical applications. Thin films of pHEMA were deposited using photoinitiated CVD (piCVD). Incorporation of ethylene glycol diacrylate (EGDA) into the pHEMA polymer film as a crosslinker, confirmed via Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy, resulted in varied swelling and degradation behavior. 2-Hydroxyethyl methacrylate-only films showed significant thickness loss (up to 40%), possibly due to extraction of low-molecular-weight species or erosion, after 24 h in aqueous solution, whereas films crosslinked with EGDA (9.25-12.4%) were stable for up to 21 days. These results differ significantly from those obtained with plasma-polymerized pHEMA, which degraded steadily over a 21-day period, even with crosslinking. This suggests that the piCVD films differ structurally from those fabricated via plasma polymerization (plasma-enhanced CVD). piCVD pHEMA coatings proved to be good cell culture materials, with Caco-2 cell attachment and viability comparable to results obtained on tissue-culture polystyrene. Thus, thin film CVD pHEMA offers the advantage of enabling conformal coating of a cell culture substrate with tunable properties depending on method of preparation and incorporation of crosslinking agents. © 2013 Wiley Periodicals, Inc.