WorldWideScience

Sample records for glycerin

  1. The physical properties of glycerin

    International Nuclear Information System (INIS)

    Kimsanov, B.Kh.; Karimov, M.B.; Khuseynov, K.

    1998-01-01

    In this chapter of book authors describe physical properties of glycerin. The pure glycerin presents syrup-vivid insipid transparent solution odorless and sweet on taste. The glycerin is very hygroscopic and can absorb from air till 40% moisture against its mass

  2. Other glycerin reactions

    International Nuclear Information System (INIS)

    Kimsanov, B.Kh.; Karimov, M.B.; Khuseynov, K.

    1998-01-01

    At the dehydration of glycerin under at the action of water-take substances (KHSO 4 , HBO 3 , waterless MgSO 4 ) forms acrolein. Acrolein at the careful oxidation change into acrylic acid, which is monomer for synthesis of polymer materials

  3. The chemistry of glycerin

    International Nuclear Information System (INIS)

    Kimsanov, B.Kh.; Karimov, M.B.; Khuseynov, K.

    1998-01-01

    This book dedicated to chemistry of polyatomic alcohols, in particular, to glycerin and its numerous derivatives. These compounds are very widespread in the natural objects and carry out several functions in alive organism. Big part of these matters are arrange in industry production of base organic synthesis

  4. The simple ethers of glycerin

    International Nuclear Information System (INIS)

    Kimsanov, B.Kh.; Karimov, M.B.

    1998-01-01

    From glycerin derivatives the considerable interest is present simple ethers because many of them are biological active and found wide practical using as an effect drugs, inters for thin organic synthesis, vehicle for injections, regulators of plants growth, reagents, components for perfumery-cosmetic goods and etc

  5. Glycerine Treated Nanofibrillated Cellulose Composites

    Directory of Open Access Journals (Sweden)

    Esra Erbas Kiziltas

    2016-01-01

    Full Text Available Glycerine treated nanofibrillated cellulose (GNFC was prepared by mixing aqueous nanofibrillated cellulose (NFC suspensions with glycerine. Styrene maleic anhydride (SMA copolymer composites with different loadings of GNFC were prepared by melt compounding followed by injection molding. The incorporation of GNFC increased tensile and flexural modulus of elasticity of the composites. Thermogravimetric analysis showed that as GNFC loading increased, the thermal stability of the composites decreased marginally. The incorporation of GNFC into the SMA copolymer matrix resulted in higher elastic modulus (G′ and shear viscosities than the neat SMA copolymer, especially at low frequencies. The orientation of rigid GNFC particles in the composites induced a strong shear thinning behavior with an increase in GNFC loading. The decrease in the slope of elastic modulus with increasing GNFC loading suggested that the microstructural changes of the polymer matrix can be attributed to the incorporation of GNFC. Scanning electron microscopy (SEM images of fracture surfaces show areas of GNFC agglomerates in the SMA matrix.

  6. Glycerin-Based Hydrogel for Infection Control.

    Science.gov (United States)

    Stout, Edward I; McKessor, Angie

    2012-02-01

    Infection is a major problem in the health and wellbeing of patients in hospitals, nursing homes, and other medical facilities as well as the homecare patients and the general public. According to Scientia Advisors, wound care costs the healthcare system over $7 billion in 2009. After adding the cost associated with potential complications such as infections, extended physician care, and lengthy hospital stays, the annual wound care expenditures well exceeded over $20 billion. 1 There are 20 million reported cases of diabetes per year and more every day. Because of the fact that leg ulcers are the number one health problem of men coupled with the rise in drug resistance of infections, the importance of providing the professional and the public with relatively simple and affordable wound care is of extreme importance. Often the wounds can become chronic wounds, which then result in long-term nursing expense in time and supplies or, worse yet, can result in expensive amputations ranging from $5000 to $40,000 per patient. There are many dressing options now available for treating wounds with components such as glycerin, honey, salt, and many other natural products, with some dressings being more appropriate than others. In 1988, a patented glycerin-based dressing was introduced to the market, called Elasto-Gel™. 2. Elasto-Gel™ is a glycerin-based gel sheet (65%) combined with a hydrophilic polymer that causes the sheet to absorb the exudate from the wound and simultaneously release the glycerin from the gel, which adds many benefits to the wound for excellent healing outcomes. The gel sheet is 1/8th of an inch thick with a four-way stretch backing. It has the ability to absorb 3-4 times its own weight of fluids. The dressing will not dry out or allow the exudate to dry out, thus keeping the dressing from becoming bonded to the wound or the surrounding tissue. It does not have adhesive properties and, therefore, will not cause damage to the wound bed or periwound

  7. Glycerine associated molecules with herbicide for controlling ...

    African Journals Online (AJOL)

    ciganinha”, belongs to the family Bignoniaceae. The only way to control this plant species in crop fields is by the application of herbicides on the stump or directly on the stem. The present study aimed to analyze the effect of glycerine in controlling A.

  8. Evaluation of Dietary Glycerin Inclusion During Different Broiler Rearing Phases

    Directory of Open Access Journals (Sweden)

    LW Freitas

    Full Text Available ABSTRACT The objective of this study was to evaluate the effect of the dietary addition of different levels of glycerin on the performance, litter moisture, pododermatitis incidence, and carcass and parts yield of broilers. In total, 1,610 broilers were reared in 35 pens with 46 birds each. A completely randomized experimental design, with five treatments with seven replicates was applied. The experimental treatments were: T1: control diet; T2: dietary inclusion of 5% glycerin from 1-42 days of age; T3: dietary inclusion of 10% glycerin from 1-42 days of age; T4: dietary inclusion of 5% glycerin from 7-42 days of age; T5: dietary inclusion of 10% glycerin from 7-42 days of age. The diets containing glycerin fed since the pre-starter period improved broiler weight gain and feed conversion ratio, but did not influence feed intake or livability. At the end of the experiment, the production efficiency index of the broilers fed 10% glycerin during the entire rearing period was significantly reduced compared with the other treatments. Litter moisture in the pens of broilers fed 10% glycerin during the entire rearing period was higher compared to the other treatments since day 21.Diets containing 10% glycerin, both for the entire rearing period (1-42 days or only after the pre-starter phase (7-42 days, influenced broiler performance and incidence of severe pododermatitis, reducing the production efficiency indexes at 42 days. Glycerin may be added up to 5% in broiler´s diets with no effect on performance, litter moisture and carcass yield, indicating that this co-product of the biodiesel industry can be used as an alternative feedstuff for broilers.

  9. Crude glycerin in the supplement for beef cattle on pasture

    OpenAIRE

    San Vito, Elias [UNESP

    2015-01-01

    Four experiments were conducted during the dry and rainy season, in order to assess the increasing concentrations of crude glycerin (80% glycerol) in the supplement of young Nellore grazing tropical grass, on intake, digestibility, ruminal fermentation, rumen microorganism profile, performance, methane emission, and carcass and meat quality traits. The treatment consist of supplements with increasing concentrations (0, 70, 140, 210, and 280 g/kg DM basis of supplement) of crude glycerin, fed ...

  10. Crude glycerin in diets for feedlot Nellore cattle

    Directory of Open Access Journals (Sweden)

    Eric Haydt Castello Branco van Cleef

    2014-02-01

    Full Text Available Two studies were conducted to evaluate the effects of crude glycerin on feed intake, performance, carcass characteristics, and total digestibility of Nellore bulls. In experiment 1, cattle (n = 30 were fed a control diet without crude glycerin and diets containing 7.5, 15, 22.5, and 30% crude glycerin, for 103 d. Animals were harvested and data of carcass characteristics were collected. In experiment 2, a digestibility trial was performed using indigestible acid detergent fiber (iADF as internal marker, and five rumen-cannulated steers. Both experiments were conducted as a randomized complete block design and data were analyzed using mixed procedures. In experiment 1 no differences were observed among treatments on dry matter intake, and performance variables. Regarding carcass characteristics, no effect was observed, except for carcass fat estimates, which were greater in treatments with crude glycerin. In experiment 2, crude glycerin promoted a decrease in digestibility of fibrous fractions NDF and HEM, and increased digestibility of crude protein by 6%. Although it caused negative effect on digestibility of fibrous fraction of diets, crude glycerin can be a good energy source for Nellore bulls, since no losses are observed on performance and carcass characteristics when animals are fed up to 30% of this by-product.

  11. 40 CFR 417.50 - Applicability; description of the glycerine distillation subcategory.

    Science.gov (United States)

    2010-07-01

    ... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE... production of finished glycerine of various grades (e.g., USP) through concentration from crude glycerine by...

  12. Analysis of glycerin waste in A-Area sanitary treatment facility material

    International Nuclear Information System (INIS)

    1995-01-01

    TNX has a large supply of 55 gallon drums containing pure glycerin and glycerin with additives. The glycerin drums were procured to simulate the glass stream in a pilot-scale melter process at TNX. Since the glycerin was not used for this process, TNX is looking at disposing the material in a sanitary waste treatment facility onsite. The effect of adding the contents of the drums to sewage bacteria was tested. A drum of pure glycerin and a drum of glycerin mixed with lithium chloride were tested. The test consisted of mixing sanitary sludge material with the glycerin material. The purpose of the test was to determine if the glycerin impacted the aerobic bacterial population. The bacterial densities were determined by taking samples from the sludge/glycerin mixtures and using aerobic plate count methods. The total organic carbon (TOC) levels were measured before and after testing. The results indicate that the cell density of the aerobic bacteria increased with the addition of glycerin and the glycerin mixture and the TOC removal rate was different for all tests. Disposal of glycerin in the wastewater treatment facilities should pose no problems. Additional testing and analysis of the mixed samples should be done before its disposal in a waste water treatment facility

  13. Glycerin Reformation in High Temperature and Pressure Water

    Science.gov (United States)

    2012-01-01

    filtration, belt filtering and flotation , among others (98, 103). The remaining material can undergo anaerobic digestion to produce methane, burned to...132–135). In that same 1933 patent, acrolein was produced from glycerin using a copper phosphate catalyst (132). Many studies have been published...carried out over a catalyst of copper and zinc oxide on an alumina support (198, 199). The high temperature F-T can accommodate some carbon dioxide

  14. Gravimetric analysis and differential scanning calorimetric studies on glycerin-induced skin hydration.

    Science.gov (United States)

    Lee, Ae-Ri Cho; Moon, Hee Kyung

    2007-11-01

    A thermal gravimetric analysis (TGA) and a differential scanning calorimetry (DSC) were carried out to characterize the water property and an alteration of lipid phase transition of stratum corneum (SC) by glycerin. In addition, the relationship between steady state skin permeation rate and skin hydration in various concentrations of glycerin was investigated. Water vapor absorption-desorption was studied in the hairless mouse stratum corneum. Dry SC samples were exposed to different conc. of glycerin (0-50%) followed by exposure to dry air and the change in weight property was monitored over time by use of TGA. In DSC study, significant decrease in DeltaH of the lipid transition in 10% glycerin and water treated sample: the heat of lipid transition of normal, water, 10% glycerin treated SC were 6.058, 4.412 and 4.316 mJ/mg, respectively. In 10% glycerin treated SCs, the Tc of water shifts around 129 degrees C, corresponding to the weakly bound secondary water. In 40% glycerin treated SC, the Tc of water shifts to 144 degrees C corresponding to strongly bound primary water. There was a good correlation between the hydration property of the skin and the steady state skin flux with the correlation coefficient (r2=0.94). As the hydration increased, the steady state flux increased. As glycerin concentration increased, hydration property decreased. High diffusivity induced by the hydration effect of glycerin and water could be the major contributing factor for the enhanced skin permeation of nicotinic acid (NA).

  15. Mono-fermentation of glycerine - Fermentation of a substrate in a dominant amount. Final report; Monovergaerung von Glycerin - Vergaerung von einem Substrat in dominierender Menge. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Erb, D.; Bueeler, E.; Spicher, M.

    2008-02-15

    The present study investigated the feasibility of a mono fermentation of the glycerine-fraction from biodiesel production. Part of the experiments took place in a single-stage, continuous system with 700 l usable volume. The maximum yield of biogas of the glycerine-fraction is 1100 l/l of glycerine, or 870 l/kg of glycerine, in continuous operation. The average methane content is 70 %. The adaptation rate of the biomass at the substrate of glycerine-fraction is high. Two or three days after starting the feed 100 % degradation rates will be achieved. The single-stage, continuous fermentation of the glycerine-fraction at 40 {sup o}C runs only stable at very low organic loading rate (0.65 kg oDM/(d m{sup 3})) and is therefore not currently economical. At higher organic loading rates (1.5 to 3.0 kg oDM/(d m{sup 3})) the adapted biomass collapsed after about 20 days due to massive instability of the process. A two-stage system with separate hydrolysis stage could probably allow a stable fermentation as search for literature has shown. Fed-batch experiments in the laboratory of the University of Waedenswil, Switzerland (ZHAW) demonstrated that the glycerine-fraction from biodiesel production is slightly better degradable than pure glycerine. The process dysfunctions arise because of the inhibition of intermediates resulting from the degradation of glycerine. At higher concentrations of 1.2-propanediol and 2.3-butanediol the degradation was incomplete. Further inhibitors can not be excluded. The failed stability of the process is not due to the lack of main nutrients or trace elements. (author)

  16. Dynamics of glycerine and water transport across human skin from binary mixtures.

    Science.gov (United States)

    Ventura, S A; Kasting, G B

    2017-04-01

    Skin transport properties of glycerine and water from binary mixtures contacting human skin were determined to better understand the mechanism of skin moisturization by aqueous glycerine formulations. Steady-state permeation for 3 H 2 O and 14 C-glycerine across split-thickness human skin in vitro and desorption dynamics of the same permeants in isolated human stratum corneum (HSC) were experimentally determined under near equilibrium conditions. These data were compared to a priori values developed in the context of a thermodynamic model for binary mixtures of glycerine and water and a previously determined water sorption isotherm for HSC. This allowed the estimation of diffusion and partition coefficients for each permeant in the HSC, as well as HSC thickness, as a function of composition of the contacting solution. These data may be used to estimate water retention and associated HSC swelling related to the absorption and slow release of glycerine from the skin. It took 6+ days for glycerine to completely desorb from HSC immersed in glycerine/water binary solutions. Desorption of both 3 H 2 O and 14 C-glycerine from HSC was slower in pure water than from binary mixtures, a result that is largely explained by the greater swelling of HSC in water. Parametric relationships were developed for water and glycerine intradiffusivities in HSC as functions of HSC water content, and a mutual diffusion coefficient was estimated by analogy with glycerine/water binary solutions. The intradiffusivity of 14 C-glycerine in HSC as inferred from sorption/desorption experiments was shown to be approximately 10-fold less than that inferred from permeation experiments, whereas the corresponding values for 3 H 2 O were comparable. These studies confirm that glycerine enters HSC in substantial quantities and has a long residence time therein. The coupling between bulk water and glycerine transport projected from binary solution data suggests the net effect of glycerine is to slow water

  17. A new vehicle for herbicide application using crude glycerin, a by ...

    African Journals Online (AJOL)

    This work aimed to develop oil-in-water (O/W) emulsions using crude glycerin treated with ... The crude glycerin was used to develop five stable emulsions with promising ..... Biodiesel and renewable diesel: A comparison. Progr. Energy Combust. Sci. ... Production, consumption, prices, characterization and new trends in.

  18. A new vehicle for herbicide application using crude glycerin, a by ...

    African Journals Online (AJOL)

    The supply of glycerin derived from the pre-purification of biodiesel has increased considerably in Brazil, making it necessary to identify economic and environmentally friendly applications for this byproduct. This work aimed to develop oil-in-water (O/W) emulsions using crude glycerin treated with H3PO4 for use as a ...

  19. Hydrogen production by aqueous phase catalytic reforming of glycerine

    International Nuclear Information System (INIS)

    Ozguer, Derya Oncel; Uysal, Bekir Zuehtue

    2011-01-01

    Hydrogen is believed to be the one of the main energy carriers in the near future. In this research glycerine, which is produced in large quantities as a by-product of biodiesel process, was converted to hydrogen aiming to contribute to clean energy initiative. Conversion of glycerol to hydrogen was achieved via aqueous-phase reforming (APR) with Pt/Al 2 O 3 catalyst. The experiments were carried out in an autoclave reactor and a continuous fixed-bed reactor. The effects of reaction temperature (160-280 o C), feed flow rate (0.05-0.5 mL/dak) and feed concentration (5-85 wt-% glycerine) on product distribution were investigated. Optimum temperature for hydrogen production with APR was determined as 230 o C. Maximum gas production rate was found at the feed flow rates around 0.1 mL/min. It was also found that hydrogen concentration in the gas product increased with decreasing glycerol concentration in the feed.

  20. Triacrylate of glycerin synthesis and use in network polymer

    International Nuclear Information System (INIS)

    Morita, Reinaldo Y.; Zawadzki, Sonia F.; Barbosa, Ronilson V.

    2009-01-01

    The goal of this work was the synthesis and characterization of a new cross linker: the glyceryl triacrylate. The synthesis was done by an esterification reaction between glycerin and acrylic acid and the product, called GA, was characterized by infrared and nuclear magnetic resonance (NMR- 1a) spectroscopy. The behavior was analysed after a copolymerization with methyl methacrylate monomer (MMA). It was also prepared the PMMA and GA homopolymers. The addition of glycerin triacrylate up to 2 % in the MMA monomer changed the solubility of the copolymer. This one became insoluble in organic solvents in which the pure linear poly(methyl methacrylate) was soluble. Thermal analysis showed that the addition of 2% GA didn't change the Tg value of the PMMA pure, but the GA homopolymer showed a Tg value equal to 180 C, lower than expected. It seems that GA product is working as cross linker, but some insaturation links did not react. They remain as pendent groups, causing the Tg lowering. The results suggest that the new product can be used as cross linker for the application in acrylic polymers. (author)

  1. Spectra of single-bubble sonoluminescence in water and glycerin-water mixtures

    International Nuclear Information System (INIS)

    Gaitan, D.F.; Atchley, A.A.; Lewia, S.D.; Carlson, J.T.; Maruyama, X.K.; Moran, M.; Sweider, D.

    1996-01-01

    A single gas bubble, acoustically levitated in a standing-wave field and oscillating under the action of that field, can emit pulses of blue-white light with duration less than 50 ps. Measurements of the spectrum of this picosecond sonoluminescence with a scanning monochrometer are reported for air bubbles levitated in water and in glycerin-water mixtures. While the spectrum has been reported previously by others for air bubbles in water, the spectrum for air bubbles in water-glycerin mixtures has not. Expected emission lines from glycerin were conspicuously absent, suggesting a different mechanism for light production in single-bubble sonoluminescence. Other conclusions are the spectrum for air bubbles in water is consistent with that previously reported, the radiated energy decreases as the glycerin concentration increases, and the peak of the spectrum appears to shift to longer wavelengths for the water-glycerin mixtures. copyright 1996 The American Physical Society

  2. Fat, meat quality and sensory attributes of Large White × Landrace barrows fed with crude glycerine

    Directory of Open Access Journals (Sweden)

    M. Belen Linares

    2014-07-01

    Full Text Available The use of alternative raw materials like crude glycerine in animal feed to reduce final costs could be of interest as the sector seeks to increase its competitiveness. The aims of the present work were to evaluate the effect of crude glycerine on back-fat thickness and the proximate composition of pork and to examine the effect on pork quality of using growing-finishing feeds with different percentages of crude glycerine added. For this purpose 60 crossbreed (Large White × Landrace barrows were subdivided into three groups according to the crude glycerine concentration administered in feed: C, control diet, no crude glycerine; and G2.5 and G5 with 2.5% and 5% added crude glycerine, respectively. This study evaluated proximate composition, pH, cooking losses, texture, colour coordinates, fatty acid profile, and sensorial analysis. No differences were found in any of the three groups studied (C, G2.5, G5 for measurements performed both before (with ultrasound equipment and after slaughter (millimetre ruler. The proximate composition and the physical-chemical parameters of longissimus dorsi were similar between groups. There were no differences detected (p>0.05 between the three groups as regards the CIELab coordinates, textural profile and sensory attributes. Therefore, 5% crude glycerine to replace corn could be used as an ingredient in pig feed without appreciably affecting the back-fat and meat quality characteristics.

  3. Meat quality of suckling lambs supplemented with contents of crude glycerin in creep feeding

    Directory of Open Access Journals (Sweden)

    Ana Carolina Ribeiro Sanquetta de Pellegrin

    2014-10-01

    Full Text Available The objective of this research was to evaluate the effect of crude glycerin in the supplement provided in creep feeding on the physico-chemical and sensory characteristics of meat from suckling lambs kept in pasture ryegrass. Thirty two suckling lambs, sixteen male and sixteen female, were distributed into 4 diets with different concentrations of crude glycerin: 0, 10, 20 and 30% crude glycerin, in the replacement of corn, in the isoproteic supplement (18% CP provided daily in amounts equivalent to 2% of body weight. The experimental design was randomized blocks, with each variable data submitted to analysis of variance at 5% significance and the significant results subjected to regression analysis. There was no effect (P>0,05 of contents of crude glycerin on the chemical composition and cholesterol content of lamb meat. On the other hand, there was increased linearly (P>0,05 pH and cooking losses by the use of crude glycerin. No influence (P>0,05 of crude glycerin concentration on the texture profile analysis (TPA, sensorial analysis by triangular test and even when was evaluated attributes color, tenderness and juiciness of lamb meat. Up to 30% of crude glycerin in the supplement provided in creep feeding for suckling lambs grazing ryegrass do not compromise the physical-chemical and sensorial quality of the lamb meat.

  4. The Mutagenic Potential Caused by the Emissions from Combustion of Crude Glycerin and Diesel Fuel

    Directory of Open Access Journals (Sweden)

    Daniel Terruggi Mazak

    2015-04-01

    Full Text Available This study evaluated the use of crude glycerin as an alternative of energy generation to replace the traditional fuels. The Tradescantia stamen hair mutation assay (Trad-SH was applied to study the mutagenic effects caused by the emissions generated in the direct combustion of diesel oil and glycerin in a flame tube furnace. Tradescantia inflorescences were exposed to gaseous emissions from the combustion tests in a fumigation chamber for 30-40 min. The analysis of variance and the Tukey test were applied to compare the differences between six test groups (intoxicated with emissions from glycerin and diesel oil combustion and a control group. Only one glycerin group showed statistical differences (0.05, possibly due to the complexity of the burning process and impurities, besides the acrolein present in its emissions. The high heating value (HHV of crude glycerin (25.5 MJ/kg was lower than diesel oil (45.19 MJ/kg, but it was comparable to other fuels. Although the use of glycerin as a biofuel could be an important aspect to be considered, the results showed that the glycerin had a substantial mutagenic potential similar to that of diesel oil.

  5. Qualitative characteristics of meat from young bulls fed different levels of crude glycerin.

    Science.gov (United States)

    Carvalho, J R R; Chizzotti, M L; Ramos, E M; Machado Neto, O R; Lanna, D P D; Lopes, L S; Teixeira, P D; Ladeira, M M

    2014-02-01

    The objective was to evaluate the fatty acid profile and qualitative characteristics of meat from young bulls fed crude glycerin. Forty-four animals with an initial live weight of 368 ± 4 kg were used in a completely randomized design, with four treatments: no glycerin or addition of 6, 12 or 18% glycerin. The animals were slaughtered with 519.5 ± 14.9 kg of live weight. The meat characteristics assessed were chemical composition, shear force, fatty acid concentration, color and lipid oxidation. The addition of glycerin increased the content of ether extract (P<0.05) in the muscle. A linear increase was observed (P<0.05) in the oleic acid contents (C18:1 cis 9). The saturated fatty acid (SFA) contents linearly decreased in the muscle as a function of glycerin addition. The lightness (L*) and yellowness (b*) indices increased with the use of crude glycerin (P<0.05). The crude glycerin increased the intramuscular fat and oleic acid content in the longissimus dorsi muscle. © 2013.

  6. Obtaining polyester from glycerin for synthesis of polyurethanes

    International Nuclear Information System (INIS)

    Breves, Rodolfo A.; Ghesti, Grace F.; Sales, Maria J.A.

    2014-01-01

    The use of renewable resources has been increasing, due to the development of materials that have viable applications that are environmentally friendly. In this paper, a polyester was synthesized from glycerin, with the addition of adipic acid in a molar ratio of 1: 1.5, with dilauryl tin catalyst, which was added in proportions of 1 to 3% obtained PUs from castor oil (Ricinus communis) and MDI (diphenyl methane diisocyanate). The materials were characterized by infrared spectroscopy (FTIR), nuclear magnetic resonance "1H NMR, thermogravimetry (TG) and derivative thermogravimetry (DTG). The reaction for obtaining the polyester was confirmed by FTIR, the absorption band between 1708-1730 cm"-"1 and "1H NMR, in the region 1.4 to 1.8 ppm and 2.2 to 2.6 ppm. The thermal decomposition of polyester occurred with temperature above 300 ° C. PUs showed similar thermal stability. (author)

  7. Cracking oils, etc. , glycerine, oil and coal gas

    Energy Technology Data Exchange (ETDEWEB)

    Mann, W

    1919-02-06

    In the cracking of hydrocarbon oils, the thermal decomposition of fats to obtain glycerine, the production of oil and coal gas, and the destructive distillation of coal, peat, shale, etc., the lower molecular weight products are separated, while the higher molecular weight products are separated, while the higher molecular weight products and undecomposed substances are retained for further exposure to the decomposition conditions, by interposing one or more porous septa between the decomposition chamber and the condenser or receiver. The decomposition conditions may be maintained up to the porous septum; but it is preferable to place the porous septum in a separate chamber inside or outside the decomposition vessel; and a plurality of decomposition chambers may be used in series or parallel.

  8. Digestibility of diets with glycerin for Nellore heifers in feedlot

    Directory of Open Access Journals (Sweden)

    Marisa Xavier Manço

    2012-12-01

    Full Text Available The research for not pollutants and renewable sources of energy, made the biodiesel is reused. But, its production generates the “Glycerin” (10% of biodiesel volume. This production is increasing and accumulating year by year, like other industrious by-products. With no law about discarding, scientists started to feed animals in different species with it. Rich in glycerol, it gives energy for animals and doesn't have other nutrients. It improves the alimentary conversion and does not change ruminal ambient or carcass production. For ruminants is used glycerin originated just from vegetables. This experiment aimed to discover what glycerin’s level can be used on diet. Made at the Unesp University of Campus of Jaboticabal, were used 24 heifers of Nellore in feedlot, weight of ± 265 kg in individuals stalls for 112 days. Were used three crossbreed cattle (Angus x Nellore castrated and cannulated, with ± 400 kg of weight for incubation. The “blond glycerin” used has 83% of glycerol. The proportion of Forage: Concentrate was 30:70. Corn silage was the forage. The concentrate was composed of: soy hulls, sunflower meal, urea and corn or corn more glycerin. All treatments had same percentages of protein and energy and were identified as “without glycerin” (G0, “with 10% of glycerin” (G10 and “20% of glycerin inclusion” (G20 in the dry matter of diet. Samples of food, leavings and excrements were collected. The collections of excrements were made at the superior part of them, without contact with the floor, at the moment of defecation for three consecutive days. Leavings and food were collected just before feeding. Bromatologics analyses were made according AOAC (1995, VAN SOEST and WINE (1967, HENDRIX (1993 and the digestion was made in autoclave (0,5 Kgf/cm2, 111ºC for 50 minutes, proceeding adapted of PELL and SCHOFIELD (1992. ADFi was used as indicator. Incubation was made according to CASALI et al. (2008 for 240 hours and

  9. Physico - chemical characterization of gamma irradiated PVP-honey-glycerine hydrogel

    International Nuclear Information System (INIS)

    Darmawan Darwis; Lely Hardiningsih; Farah Nurlidar

    2010-01-01

    Research to investigate physico-chemical characterizatics of hydrogel wound dressing containing 6% (b/v) of honey and various concentrations of glycerine from 0-5% (b/v) has been done. Nine series of hydrogel formulas with various composition of PVP hydrogel were irradiated using gamma rays at a dose of 25 kGy. The results showed that addition of honey 6% and glycerine up to 5% lead to the formation of hydrogel with following properties: sterile, transparence, browning color, improved flexibility, conformability to skin and resistance against mould. The PVP-honey-glycerine hydrogel also showed lower water favor evaporation at 37 o C and higher water absorption properties compared to basic formula (without additional of honey and glycerine). (author)

  10. Aerobic stability, chemical composition and ruminal degradability of sugarcane silage with glycerin from biodiesel

    Directory of Open Access Journals (Sweden)

    Marco Antonio Bensimon Gomes

    2015-06-01

    Full Text Available The experiment was performed with the objective of studying the ensiled sugarcane silage with 0, 5, 10, 15 and 20% of glycerin in experimental PVC silos. The aerobic stability was assessed by measuring the pH and the temperature of the silage at 0, 24, 48, 72, 96 and 120h. The chemical composition, the levels of non-fiber carbohydrates (NFC and the total digestible nutrients (TDN were evaluated. The in vitro digestibility of dry matter (IVDDM and the in vitro digestibility of the cell wall (IVDCW in the silages were evaluated. In three fistulated cattle the in situ degradability of dry matter (DM and the disappearance percentage of the neutral detergent fiber (NDF in samples incubated at 0, 2, 6, 12, 24, 48, 72 and 96h were analyzed. The experimental design was completely randomized and the statistical analyzes were done using Bayesian inference. Increases were observed in DM, TDN, mineral matter, NFC and reductions in NDF, acid detergent fiber, crude protein and ether extract as the inclusion of glycerin was higher. IVDDM increased (P <0.05 in silage with 15 and 20% of glycerin in relation to those with 0, 5 and 10%. The IVDCW at levels of 10, 15 and 20% of glycerin was higher (P <0.05 compared to the other treatments. Increases were observed in the soluble portion (a, a reduction in the insoluble fraction (b, and an increase in the degradability fraction constant (c of the silages with 5, 10, 15 and 20% of glycerin (P <0.05 compared to the control. Glycerin improved aerobic stability while maintaining a low pH and temperature during the observation period at levels of 15 and 20% of glycerin against the silage with 0, 5 and 10%. These results indicate glycerin as a promising additive for sugarcane silage, being able to enhance energy density and improve the aerobic stability of the ensiled matter when its inclusion is from 10 to 20%.

  11. Ingestive behavior of grazing heifers receiving crude glycerin supplementation during the dry-rainy season transition

    Directory of Open Access Journals (Sweden)

    Vitor Visintin Silva de Almeida

    2014-09-01

    Full Text Available The search to find food alternatives for corn and feeding alternatives that reduce the cost of production has been constant. The use of oleaginous grains to produce ethanol and biodiesel has produced an excess of byproducts, especially biodiesel which produces crude glycerin. The objective of this study was to evaluate the effect of including crude glycerin on the ingestive behavior of crossbred heifers supplemented with pasture. Thirty-six crossbred heifers with an initial mean weight of 301.5 ± 31 kg were distributed in a completely randomized design with four treatments and nine replicates per treatment. The animals were kept in a Brachiaria brizantha (Hochst. ex A. Rich. Stapf 'Marandu' pasture in a rotational-grazing system. The treatments tested were 0.0%, 3.33%, 6.66%, and 9.99% crude glycerin included in total DM to replace corn (Tea mays L. Including crude glycerin reduced the time for grazing and eating at the trough and increased idle time. Rumination was quadratically influenced. Eating time (min kg-1 DM and neutral detergent fiber [NDF] was reduced, while rumination time (min kg-1 DM and NDF was quadratically affected by adding glycerin. The variables, time spent per ruminated bolus and the number of chews per day, were not affected. The number of boluses per day showed a quadratic effect. The number of grazing, idle, ruminating, and eating at the trough periods were not affected by including crude glycerin; means were 15.1, 24.9, and 13.3 and 3.71 periods d-1, respectively. Feed and rumination efficiency (kg h-1 DM and NDF increased when crude glycerin was included in the diet. Including crude glycerin promotes feed and rumination efficiency in grazing heifers.

  12. Soil microbial activity and hairy beggarticks’ germination after application of crude glycerin

    Directory of Open Access Journals (Sweden)

    Matheus Ramos Caixeta

    Full Text Available ABSTRACT Biodiesel stands out as an alternative for petroleum-based products, but its production generates a large amount of by-products. This study was carried out at the Instituto Federal de Educação, Ciência e Tecnologia do Sul de Minas Gerais, Campus Machado, with the objective of evaluating the impacts of the disposal of crude glycerin on agricultural soil and its microbial activity as well as in plant development. An experiment with a completely randomized design, five treatments, and five replicates was developed in the laboratory to analyze microbial activity. Soil samples of 100 g were incubated for 36 days with concentrations of crude glycerin, namely: 0; 48.7; 146.1; 292.2 L ha-1. Besides these four treatments, flasks without soil and glycerin have composed one more treatment. During this period, the CO2 volume released in each sample was evaluated 11 times. Another experiment was developed in the laboratory with hairy beggarticks’ achenes to evaluate crude glycerin effects on plant development. A randomized complete block design was used in a 4x2 factorial scheme, with five replicates, the same glycerin concentrations, and two glycerin sources (laboratory and biodiesel plant-unit. Crude glycerin stimulated soil microbial activity for doses of up to 143.83 L ha-1, being a positive indicative for future studies on its application to agricultural soils. Glycerin applications reduced the hairy beggarticks’ root protrusion, even at the lowest doses. Residues have Na+ contents that limit their application in agricultural soils.

  13. Growth performance, carcass characteristics and meat quality of finishing bulls fed crude glycerin-supplemented diets

    Directory of Open Access Journals (Sweden)

    Mônica Chaves Françozo

    2013-04-01

    Full Text Available This study was conducted to evaluate the performance, carcass characteristics and chemical composition of Longissimusmuscle (LM of the bulls. Twenty-four Nellore bulls were used in a complete randomised design. The bulls were randomly assigned to one of the three diets containing 0, 5 or 12% glycerin. Final BW and ADG were similar (P>0.05 between the bulls fed with 5 or 12% of glycerin but were higher (P0.05 by glycerin level. Hot carcass weight increased (P0.05 the conformation, colour, texture, marbling and pH. There was difference (P>0.05 for moisture, ashes and crude protein among glycerin levels. Bulls fed 12% glycerin present the highest (P<0.03 total lipids on LM. The percentage of saturated fatty acids (SFA, monounsaturated acids (MUFA, polyunsaturated acids (PUFA, n-6 and n-3 fatty acids and PUFA/SFA and n-6:n-3 ratios of the LM were similar among the diets. In conclusion, glycerin level did not affect the animal performance and carcass characteristics of Nellore bulls finished in feedlot.

  14. Glycerin levels while maintaining the electrolyte balance in finishing pig diets

    Directory of Open Access Journals (Sweden)

    Rafaeli Gonçalves Leite

    Full Text Available ABSTRACT The objective of this study was to evaluate performance and carcass and meat characteristics of finishing pigs fed diets with different levels of glycerin, while maintaining the electrolyte balance. Forty barrows with an initial weight of 97.76±13.44 kg were distributed, in a randomized block design, into four treatments with five replicates. Treatments consisted of diets containing 0, 5, 10, and 15% glycerin. Inclusions of salt and sodium bicarbonate were adjusted to balance the sodium content and maintain the same electrolyte balance of the diets as a function of glycerin inclusions. In vivo backfat thickness, daily feed intake, daily weight gain, and feed conversion were measured. After the animals were slaughtered, pH and temperature were measured 45 min and 24 h postmortem, and backfat thickness, loin-eye area, drip loss, and colorimetry were determined. Glycerin inclusion levels did not influence the performance of barrows. Hot carcass weight, dressing percentage, and lightness had higher values when pigs were fed diets containing 2.32, 2.43, and 2.61% glycerin, respectively. The other carcass and meat characteristics were not influenced. Glycerin can be used in finishing pig diets without compromising results of performance or carcass and meat characteristics up to the inclusion level of 15%.

  15. From cross-linking to plasticization - characterization of Glycerin/HTPB blends

    Energy Technology Data Exchange (ETDEWEB)

    Kohga, Makoto [Department of Applied Chemistry, National Defense Academy, Hashirimizu, Yokosuka, Kanagawa (Japan)

    2009-10-15

    Usually, a plasticizer is a relatively low-viscosity liquid ingredient that is added to improve the mechanical properties and the processing properties of a propellant, such as a lower viscosity for casting or a longer pot life of the mixed, but uncured propellant. The effects of many plasticizers on the performance of the composite propellant have been studied in detail. Glycerin is a triol, a low viscosity material, and inexpensive. It seems that the processing properties and the mechanical properties of the HTPB binder would be improved by the addition of glycerin. The curing behavior, the mechanical properties, and the thermal decomposition of a glycerin/HTPB blend have been investigated in this study. The viscosity of the glycerin/HTPB blend and the increasing ratio of the viscosity versus the elapsed time are lower than those of only HTPB. The mechanical properties are improved by the addition of glycerin, even for a low quantity of glycerin. The thermal decomposition behavior of the blend occurs at lower temperatures when compared to that of HTPB. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  16. Co-digestion of swine excreta associated with increasing levels of crude glycerin

    Directory of Open Access Journals (Sweden)

    Marco Antonio Previdelli Orrico Junior

    2016-03-01

    Full Text Available ABSTRACT The objective of this research was to evaluate the performance of anaerobic co-digestion of swine excreta associated with increasing doses of crude glycerin and different hydraulic retention times (HRT. A completely randomized design was adopted in a 3 × 4 factorial arrangement composed of three HRT (10, 17, and 24 days and four crude glycerin doses (0, 5, 10, and 15 g/100 g of total solids [TS], with four replications per treatment. The assessed parameters were: biogas production potential, reductions of volatile solids (VS, chemical oxygen demand (COD, and most probable number of total and thermotolerant coliforms. The biogas production per added VS presented quadratic effect at 17 and 24 days of HRT, with ideal doses of 5.5 and 5.9 g of crude glycerin/100 g TS, respectively. There was no difference among glycerin doses at 10-day HRT for VS reductions; however, at HRT of 17 and 24 days, there were differences, with greater reduction of 61.1% for 5 g of crude glycerin/100 g TS at 24-day HRT. The COD reduction values showed an effect among retention times, in which the 24-day HRT provided the best results. Reductions in coliforms were greater than 99%, with no difference among treatments. Addition of 5 to 6 g of crude glycerin/100 g TS with a 24-day HRT is more effective in biogas production and reduction of VS, COD, and coliforms from co-digestion of swine excreta.

  17. Glycerin Suppositories Use in Very Low Birth Weight Infants.

    Science.gov (United States)

    Patel, Shalinkumar; Dereddy, Narendra; Talati, Ajay J; Gaston, Kan; Dhanireddy, Ramasubbareddy

    2017-01-01

    Objective  To study the characteristics of very low birth weight (VLBW) infants receiving glycerin suppositories (GS) and evaluate the association of GS use with outcomes. Study Design  This is a retrospective study of VLBW infants admitted to a level III neonatal intensive care unit. Infants with birth weight between 500 and 1,499 g were evaluated. We evaluated the frequency of GS use and compared the characteristics and outcomes of the GS group with the no-GS group. Multivariate analyses controlling for gestational age and small for gestational age status were performed to study the effect of GS on outcomes. Results  A total of 1,073 infants were included in the study. Out of those, 527 (49.1%) infants received GS. Incidence of necrotizing enterocolitis was not significantly different between the two groups, while days to reach full enteral feeds and length of hospital stay were significantly longer in the GS group. Conclusion  Frequent use of GS warrants further prospective studies to evaluate its safety and efficacy in view of our study showing association with longer time to reach full enteral feeds. We speculate that GS use could be a marker for gastrointestinal dysmotility and hence the association with unfavorable clinical outcomes. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

  18. Performance and carcass characteristics of lambs fed on diets supplemented with glycerin from biodiesel production

    Directory of Open Access Journals (Sweden)

    Marco Antonio Bensimon Gomes

    2011-10-01

    Full Text Available This study was carried out to evaluate the influence of diets supplemented with glycerin as an alternative ingredient to corn on the performance and carcass characteristics of Santa Inês confined lambs. The study involved 27 lambs aged 90 days, having an average initial weight of 26.33 ± 0.15 kg. Lambs were randomly distributed into a control group and groups with diets containing 15 and 30% glycerin in the total feed. Diet was formulated with 40% roughage and 60% concentrate. The experimental design was completely randomized, and the production performance and carcass characteristics were analyzed by analysis of variance, and the subjective carcass characteristics, by general linear models. The daily average gain was 0.21, 0.24 and 0.23 kg/day; feeding conversion was 6.39, 5.73 and 5.92 kg of diet/kg BW for control animals, and those fed with 15 or 30% glycerin, respectively, without treatment differences. Lambs were slaughtered, weighing 34 to 36 kg, and average weight of the cold carcass and commercial carcass yield were evaluated. The results were, respectively, 15.97 kg and 49.18%, for control, 15.96 kg and 48.31% for animals fed with 15% glycerin, and 15.79 kg and 47.87% for those treated with 30% glycerin, with no treatment effects. Meat tenderness and cooking loss averages were not affected by diets, with 5.07 kg and 40.45%, 5.10 kg and 40.81%, and 5.27 kg and 39.04%, respectively, for control, and those fed with 15 or 30% glycerin. Therefore, it is possible to conclude that up to 30% of medium purity glycerin in the dry matter of the diet can be used to replace corn, without any negative effect on lamb performance or carcass characteristics.

  19. Performance, rumen development, and carcass traits of male calves fed starter concentrate with crude glycerin

    Directory of Open Access Journals (Sweden)

    Raylon Pereira Maciel

    2016-06-01

    Full Text Available ABSTRACT The objective of this study was to assess the effects of including crude glycerin in the diet on intake, performance, rumen development, and carcass traits of dairy crossbred veal calves fed starter concentrate containing 0, 80, 160, and 240 g kg−1 crude glycerin. Twenty-eight calves with an average weight of 38.03±6.7 kg and five days of age were distributed in a completely randomized design with four treatments with seven replications. Calves were individually housed in covered stalls equipped with feeders and drinkers for 56 days. The calf response to inclusion of crude glycerin in the concentrate changed over the weeks and the inclusion level of 240 g kg−1 resulted in greater dry matter intake and average daily gain. There was no effect on the final weight and total weight gain of the animals, with mean values of 73.60 and 35.16 kg, respectively. The weight of the rumen-reticulum adjusted for body weight, empty body weight, and total stomach weight increased linearly with the inclusion of crude glycerin. Blood total protein, globulin, urea, cholesterol, gamma glutamyl transferase, aspartate aminotransferase, and alkaline phosphatase concentrations did not differ among treatments. Carcass traits and meat color were not affected. Crude glycerin can be added to dairy calf starter concentrate up to 240 g kg−1 dry matter because it benefits concentrate intake, performance, and rumen development without affecting animal health.

  20. Ingestive Behavior of Heifers Supplemented with Glycerin in Substitution of Corn on Pasture

    Directory of Open Access Journals (Sweden)

    L. M. A. M. Facuri

    2014-11-01

    Full Text Available The objective was to evaluate the ingestive behavior of crossbred heifers finished on a Brachiaria brizantha cv. Marandu pasture receiving four levels of glycerin in their supplementation. Thirty-six crossbred heifers with average initial weight of 264.83±3.83 kg and 20 months of age were distributed into a completely randomized design with four treatments and nine replications: control (0%, 4.82%, 10.12%, and 15.56% glycerin in the dry matter. The grazing time reduced linearly (p0.05. The number of rumination periods reduced linearly (p0.05 whereas the feed efficiency of neutral detergent fiber reduced linearly (p<0.05. Addition of glycerin in substitution of corn in supplements for animals managed on pastures does not influenced feed intake, but reduces the grazing time and increases the idle time. The supplementation also improves feed and rumination efficiencies.

  1. Ingestive Behavior of Heifers Supplemented with Glycerin in Substitution of Corn on Brachiaria brizantha Pasture.

    Science.gov (United States)

    Facuri, L M A M; Silva, R R; da Silva, F F; de Carvalho, G G P; Sampaio, C B; Mendes, F B L; Lisboa, M M; Barroso, D S; Carvalho, V M; Pereira, M M S

    2014-11-01

    The objective was to evaluate the ingestive behavior of crossbred heifers finished on a Brachiaria brizantha cv. Marandu pasture receiving four levels of glycerin in their supplementation. Thirty-six crossbred heifers with average initial weight of 264.83±3.83 kg and 20 months of age were distributed into a completely randomized design with four treatments and nine replications: control (0%), 4.82%, 10.12%, and 15.56% glycerin in the dry matter. The grazing time reduced linearly (p0.05). The number of rumination periods reduced linearly (p0.05) whereas the feed efficiency of neutral detergent fiber reduced linearly (p<0.05). Addition of glycerin in substitution of corn in supplements for animals managed on pastures does not influenced feed intake, but reduces the grazing time and increases the idle time. The supplementation also improves feed and rumination efficiencies.

  2. Glycerin in cattle feed: intake, digestibility, and ruminal and blood parameters

    Directory of Open Access Journals (Sweden)

    Vanessa Ruiz Fávaro

    2015-06-01

    Full Text Available This study aimed to evaluate the effects of glycerin supplements in the diet of beef cattle by assessing intake, apparent nutrient digestibility, ruminal pH, ruminal ammonia concentrations, and blood parameters. The study was conducted at the São Paulo State University (UNESP, Jaboticabal campus using five crossbred cattle in an experiment employing a 5 x 5 Latin square design. Cattle diet treatments included zero, 50, 100, 150, and 200 g kg-1 dry matter of glycerin. Feed, leftover feed, and faeces were collected to determine intake and digestibility. Samples of ruminal liquid were collected at –1, 0, 1, 2, 4, 6 and 8 h after feeding to determine pH and ruminal ammonia. Blood was collected four hours after the morning feeding from the coccygeal vein. Replacing maize with glycerin resulted in lower concentrations of ether extract and non-fibre carbohydrates in the diets, leading to a linear decrease in the intake of these nutrients (P<0.05. The digestibility of neutral detergent fibre and non-fibre carbohydrates also decreased linearly with increasing dietary glycerin concentrations (P<0.05. The results for ruminal fermentation parameters showed a linear decrease (P<0.05 in the ruminal concentration of N-NH3 with increasing dietary levels of glycerin; however, ruminal pH was not affected (P<0.05. Serum concentrations of urea, triglycerides, cholesterol, and plasma glucose concentrations were within normal ranges based on the literature. The inclusion of glycerin in the cattle diet altered rumen fermentation, reducing the concentration of N-NH 3, the digestibility of neutral detergent fiber and non-fiber carbohydrates.

  3. Synthesis and characterization of dense membranes of silk fibroin with glycerin

    International Nuclear Information System (INIS)

    Silva, Mariana F.; Moraes, Mariana A. de; Weska, Raquel F.; Nogueira, Grinia M.; Beppu, Marisa M.

    2009-01-01

    The addition of plasticizers seeks improvements in mechanical properties of dense membranes of silk fibroin with possible interactions by hydrogen bonds. The aim of the present study was to produce and characterize dense membranes of silk fibroin containing glycerin in two different concentrations. The characterization of the membranes was performed from scanning electron microscopy (SEM), mechanical traction tests, infrared spectroscopy (FTIR-ATR) and X-ray diffraction (XRD). The results indicated that the addition of glycerin allowed obtaining homogeneous and more crystalline membranes and improved their properties of elongation. (author)

  4. Microbiological viability of bovine amniotic membrane stored in glycerin 99% at room temperature for 48 months

    Directory of Open Access Journals (Sweden)

    Kelly Cristine de Sousa Pontes

    Full Text Available ABSTRACT The medium for storing biological tissues is of great importance for their optimal use in surgery. Glycerin has been proven efficient for storing diverse tissues for prolonged time, but the preservation of the bovine amniotic membrane in glycerin 99% at room temperature has never been evaluated to be used safely in surgical procedures. This study evaluated the preservation of 80 bovine amniotic membrane samples stored in glycerin 99% at room temperature. The samples were randomly divided evenly into four groups. Samples were microbiologically tested after 1, 6, 12 and 48 months of storage. The presence of bacteria and fungi in the samples was evaluated by inoculation on blood agar and incubation at 37 ºC for 48 hours and on Sabouraud agar at 25 ºC for 5 to 10 days. No fungal or bacterial growth was detected in any of the samples. It was concluded that glycerin is an efficient medium, regarding microbiology, for preserving pre-prepared bovine amniotic membrane, keeping the tissue free of microorganisms that grow in the media up to 48 months at room temperature.

  5. 21 CFR 172.866 - Synthetic glycerin produced by the hydrogenolysis of carbohydrates.

    Science.gov (United States)

    2010-04-01

    ... of carbohydrates. 172.866 Section 172.866 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... produced by the hydrogenolysis of carbohydrates. Synthetic glycerin produced by the hydrogenolysis of carbohydrates may be safely used in food, subject to the provisions of this section: (a) It shall contain not in...

  6. Qualitative characteristics of hamburgers and koftas produced from meat of lambs fed glycerine

    Directory of Open Access Journals (Sweden)

    T. H. Borghi

    2016-12-01

    Full Text Available The objective of this study was to evaluate the qualitative (pH, color, water activity, water retention capacity, cooking loss, and shear force and sensory characteristics of processed meat produced from less noble cuts of the carcasses of lambs fed diets containing sugarcane as roughage and concentrates with and without 10 and 20% glycerine. Neck and rib meat of 30 lambs slaughtered at a body weight of 32.0 ± 0.2 kg was used for the elaboration of hamburgers and koftas. Except for color, the inclusion of glycerine in the lamb diet did not influence (P>0.05 the qualitative traits evaluated. The inclusion of glycerine reduced the redness (from 10.07 to 8.89, P=0.044 and yellowness (from 5.97 to 5.07, P=0.039 of hamburgers. The same effect was observed for the redness (from 10.83 to 9.61, P=0.031 and yellowness (from 5.86 to 5.12, P=0.047 of koftas. The sensory characteristics evaluated were not influenced (P>0.05 and the grades of overall acceptance ranged from 7.4 to 7.9. The inclusion of glycerine in the diet of lambs altered the color of processed meat products, but provided satisfactory sensory characteristics.

  7. Glycerine derived from biodiesel production as a feedstuff for broiler diets

    Directory of Open Access Journals (Sweden)

    CLS Silva

    2012-09-01

    Full Text Available The performance, carcass traits, and litter humidity of broilers fed increasing levels of glycerine derived from biodiesel production were evaluated. In this experiment, 1,575 broilers were distributed according to a completely randomized experimental design into five treatments with seven replicates of 45 birds each. Treatments consisted of a control diet and four diets containing 2.5, 5.0, 7.5, or 10% glycerine. The experimental diets contained equal nutritional levels and were based on corn, soybean meal and soybean oil. The glycerine included in the diets contained 83.4% glycerol, 1.18% sodium, and 208 ppm methanol, and a calculated energy value of 3,422 kcal AMEn/kg. Performance parameters (weight gain, feed intake, feed conversion ratio, live weight, and livability were monitored when broilers were 7, 21, and 42 days of age. On day 43, litter humidity was determined in each pen, and 14 birds/treatment were sacrificed for the evaluation of carcass traits. During the period of 1 to 7 days, there was a positive linear effect of the treatments on weight gain, feed intake, and live weight gain. Livability linearly decreased during the period of 1 to 21 days. During the entire experimental period, no significant effects were observed on performance parameters or carcass traits, but there was a linear increase in litter humidity. Therefore, the inclusion of up to 5% glycerine in the diet did not affect broiler performance during the total rearing period.

  8. Crude glycerine inclusion in Limousin bull diets: animal performance, carcass characteristics and meat quality.

    Science.gov (United States)

    Egea, M; Linares, M B; Garrido, M D; Villodre, C; Madrid, J; Orengo, J; Martínez, S; Hernández, F

    2014-12-01

    Three hundred and six Limousin young bulls (7±1months of age, initial body weight 273±43kg) were used to evaluate the effect of crude glycerine supplementation on animal performance, carcass characteristics and meat quality. Animals were assigned to three different diets: Control (0% of crude glycerine), G2 and G4 (2 and 4% of crude glycerine, respectively). The diets were administrated ad libitum for 240days (final body weight 644±24kg). Average daily weight gain, average daily feed intake, the gain:feed ratio, ultrasound measures in vivo, carcass characteristics, pH, water holding capacity, drip losses, and cooking losses were not affected (P>0.05) by diets. Diet decreased C16:0 (P<0.01) and C16:1 (P<0.05) contents in meat. The G4 meat showed lower C12:0, C14:0, C17:0, C18:0, C18:1, C18:2, C18:3, c9,t11-c18:2, C20:0 and C20:4 levels (P<0.05) than control. Glycerine increased desirable fatty acid percentages (P<0.05) in intramuscular fat. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Feeding behavior of Nellore cattle fed high concentrations of crude glycerin

    Directory of Open Access Journals (Sweden)

    Eric Haydt Castello Branco Van Cleef

    2015-07-01

    Full Text Available The objective of this study was to evaluate the inclusion of up to 30% crude glycerin in Nellore cattle diets and its effects on feeding behavior parameters. It were used 30 animals with 277.7kg BW and 18 months old, which were kept in feedlot in individual pens during 103 days (21 adaptation and 82 data collection. The animals were assigned (initial weight in blocks and submitted to the following treatments: G0; G7.5; G15; G22.5; and G30, corresponding to control group, 7.5, 15, 22.5, and 30% crude glycerin in the diet dry matter, respectively. The feeding behavior (feeding, idle, ruminating, number of chews, feeding efficiency and ruminating efficiency were evaluated for three days. Data were analyzed as a completely randomized block design, analyzing contrasts and observing the significance of linear, quadratic and control treatment × glycerin treatments effects. The inclusion up to 30% crude glycerin in diets of Nellore cattle altered the feeding efficiency, expressed in g NDF h-1, the ruminating efficiency relative to NDF, the time and number of chews per ruminal bolus, facilitating the feed ingestion and directly influencing the time spent on feeding.

  10. Bioconversion from crude glycerin by Xanthomonas campestris 2103: xanthan production and characterization

    Directory of Open Access Journals (Sweden)

    L. V. Brandão

    2013-12-01

    Full Text Available The production and rheological properties of xanthan gum from crude glycerin fermentation, a primary by-product of the biodiesel industry with environmental and health risks, were evaluated. Batch fermentations (28 °C/250 rpm /120 h were carried out using crude glycerin, 0.01% urea and 0.1% KH2PO4, (% w/v, and compared to a sucrose control under the same operational conditions, using Xanthomonas campestris strain 2103 isolate from Brazil. Its maximal production by crude glycerin fermentation was 7.23±0.1 g·L-1 at 120 h, with an apparent viscosity of 642.57 mPa·s, (2 % w/v, 25 °C, 25 s-1, 70% and 30% higher than from sucrose fermentation, respectively. Its molecular weight varied from 28.2 to 36.2×10(6 Da. The Ostwald-de-Waele model parameters (K and n indicated a pseudoplastic behavior at all concentrations (0.5 to 2.0 %, w/v and temperatures (25-85 °C, while its consistency index indicated promising rheological properties for drilling fluid applications. Therefore, crude glycerin has potential as a cost-effective and alternative substrate for non-food grade xanthan production.

  11. Ingestive behavior of lactating cows fed sugarcane and crude glycerin levels on the diet

    Directory of Open Access Journals (Sweden)

    Lucas Teixeira Costa

    2014-09-01

    Full Text Available The crude glycerin used as feed for ruminants has drawn attention of the researchers for dealing with environmental aspects. Considering current legislation did not establish how to treat this product, this is a low cost alternative of great amount of a residue of the biodiesel production. In this study we evaluated different crude glycerin levels on ingestive behavior which were studied as the diet of lactating cows fed with sugarcane. The glycerin levels were 0, 4, 8 and 12% of the dry matter; the diet was balanced to contain enough nutrients for the maintenance and milk production of 15 kg.dia-1. Sixteen (16 crossbred Holstein x Zebu cows were distributed into four 4x4 Latin Squares. The animals were submitted to observation of 24 hours every five minutes to evaluate ingestive behavior. The observation of the activities was recorded. The animal´s behavior was visually determined with five minutes of intervals to determine the times spent in idle, feeding, rumination, and were calculated patterns of feeding and rumination. The addition of glycerin to the diet did not affect the ingestive behavior parameter in lactating cows fed sugarcane, might be explained by the similarity in NDF content of diets, and up to 12% may be added of the diet’s dry matter.

  12. Crude glycerin decreases nonesterified fatty acid concentration in ewes during late gestation and early lactation.

    Science.gov (United States)

    Polizel, D M; Susin, I; Gentil, R S; Ferreira, E M; de Souza, R A; Freire, A P A; Pires, A V; Ferraz, M V C; Rodrigues, P H M; Eastridge, M L

    2017-02-01

    Crude glycerin is a gluconeogenic substrate in ruminants and may help to decrease the occurrence of pregnancy toxemia. The objective in this trial was to determine the effects of feeding a diet containing crude glycerin on DMI, milk yield, milk composition, and blood metabolites in periparturient ewes and lamb performance. One hundred eighteen 90 (±1.1)-d pregnant Santa Inês ewes were used. After lambing, 32 ewes (62.8 ± 1.3 kg BW) were allotted in a randomized complete block design defined by prelambing diet, BW, BCS, lambing date, type of birth (single or twin), and sex of offspring. Diets were isonitrogenous (13.0 ± 0.3% CP, DM basis), composed of concentrate and raw sugarcane bagasse (70:30 ratio, DM basis), and fed ad libitum daily. Crude glycerin (83.6% glycerol) levels were 0 or 10% (DM basis), corresponding to the experimental diets G0 and G10, respectively. From 8 until 56 d of lactation, DMI was determined. In the same period, once a week at 1000 h, the ewes were separated from the lambs and mechanically milked after intravenous administration of 10 IU of synthetic oxytocin. Three hours after the first milking, ewes were milked again and milk yield and composition were determined. Glucose, NEFA, and β-hydroxybutyrate (BHBA) were determined at -14, -7, 0, 7, 14, 28, and 56 d relative to lambing and insulin was determined at -14, -7, 0, and 7 d. Crude glycerin did not affect DMI (2.2 kg/d for G0 vs. 2.2 kg/d for G10; = 0.93) or milk production (171 g/3 h for G0 vs. 164 g/3 h for G10; = 0.66). However, there was a decrease ( = 0.01) in milk fat percentage (8.1% for G0 vs. 7.0% for G10) for ewes fed glycerin. Ewes fed the G10 diet had decreased ( ewes fed the G10 diet (0.46 mmol/L for G0 vs. 0.61 mmol/L for G10). There was no effect of diets fed to ewes on lamb growth from birth to weaning. Crude glycerin improved energy balance of periparturient ewes, suggesting a reduced risk of developing clinical metabolic-related disorders. Crude glycerin can be

  13. Glycerin enemas and suppositories in premature infants: a meta-analysis.

    Science.gov (United States)

    Livingston, Michael H; Shawyer, Anna C; Rosenbaum, Peter L; Williams, Connie; Jones, Sarah A; Walton, J Mark

    2015-06-01

    Premature infants are often given glycerin enemas or suppositories to facilitate meconium evacuation and transition to enteral feeding. The purpose of this study was to assess the available evidence for this treatment strategy. We conducted a systematic search of Medline, Embase, Central, and trial registries for randomized controlled trials of premature infants treated with glycerin enemas or suppositories. Data were extracted in duplicate and meta-analyzed using a random effects model. We identified 185 premature infants treated prophylactically with glycerin enemas in one trial (n = 81) and suppositories in two other trials (n = 104). All infants were less than 32 weeks gestation and had no congenital malformations. Treatment was associated with earlier initiation of stooling in one trial (2 vs 4 days, P = .02) and a trend towards earlier meconium evacuation in another (6.5 vs 9 days, P = .11). Meta-analysis demonstrated no effect on transition to enteral feeding (0.7 days faster, P = .43) or mortality (P = 0.50). There were no reports of rectal bleeding or perforation but there was a trend towards increased risk of necrotizing enterocolitis with glycerin enemas or suppositories (risk ratio = 2.72, P = .13). These three trials are underpowered and affected by one or more major methodological issues. As a result, the quality of evidence is low to very low. Three other trials are underway. The evidence for the use glycerin enemas or suppositories in premature infants in inconclusive. Meta-analyzed data suggest that treatment may be associated with increased risk of necrotizing enterocolitis. Careful monitoring of ongoing trials is required. Copyright © 2015 by the American Academy of Pediatrics.

  14. Glycerin and essential oils in the diet of Nellore bulls finished in feedlot: animal performance and apparent digestibility

    Directory of Open Access Journals (Sweden)

    Lorrayny Galoro da Silva

    2014-05-01

    Full Text Available Current research studied the effect of partial replacing corn by glycerin and essential oils addition in the diet of Nellore bulls finished in feedlot on feed intake, animal performance and three markers were assessed to estimate apparent digestibility. Thirty bulls with average weight 400 ± 34.1 kg and 22 ± 2 months old were housed in collective pens (10 x 20 m2 for 63 days. The bulls were randomly assigned to 3 diets (10 bulls per treatment: CON – Control (without glycerin or Essential® oils; GLY – Glycerin (15% on dry matter - DM; and GEO – Glycerin (15% on DM and Essential® oils (3 g animal day-1. Three different markers were used to estimate apparent digestibility in the diets: indigestible dry matter –iDM; indigestible neutral detergent fiber – iNDF; and purified lignin – LIPE®. Feed efficiency and animal performance were not affected by the corn partial replacing by glycerin. No effects were found in partial corn replacing by glycerin and Essential® oils addition in the diets on the fecal output, crude protein and ether extract digestibility among the diets. The DM and OM apparent digestibility were higher for bulls fed with glycerin and Essential® oils. The CHO digestibility was higher for CON diet. The markers iDM, iNDF and LIPE® were similarly to estimate apparent digestibility to all nutrients in the diets.

  15. Development, economic viability and attributes of lamb carcass from confined animals fed on different amounts of crude glycerin

    Directory of Open Access Journals (Sweden)

    Fabiola Cristine de Almeida Rego

    2015-10-01

    Full Text Available The current study aims to assess the effect from crude glycerin inclusion (0, 7, 14, and 21% dry matter in the diet of slaughtered lamb on their development, nutrient consumption, biometrical measures, diet economic viability and carcass features. Thirty two (32 non-castrated male Texel lambs were used in the study, they presented mean initial weight 15.9 ± 4.1 kilos and were distributed in casual outlining. They were fed with four treatments, with 8 repetitions. Animals were slaughtered when they reached approximately 35 kilos. The mean total weight gain was 20.72 kilos and mean daily weight gain was 260 grams. No changes resulted from glycerin use. The carcass performance was similar among treatments (P>0.05 and the cold carcass performance (CCP was 44.68%. There were no effects (P>0.05 on the loin eye area (LEA and on fat thickness (FT; they showed averages of 13.66 cm2 and 0.84 mm, respectively. Nutrition cost per animal during the whole confinement period varied between R$82.60 (eighty-two Reais and forty-eight cents to R$92.48. The smallest nutrition amount consisted of 21% crude glycerin. The gross profit ranged from R$30.75 to R$ 34.01 per animal, for feed without glycerin and 21% glycerin, respectively. Animal development was not impacted by glycerin introduction, even with decrease on dry and organic mass consumption. The result showed that crude glycerin inclusion might be used in lambs’ diet. Whenever there are big amounts of feed involved in the process, the 21% crude glycerin addition may be an interesting cost reduction. Seventy eight percent (78% glycerol crude glycerin to replace corn-based feed in confined lambs’ diet appeared to be nutritionally and economically viable. 

  16. Glycerin Borax Treatment of Exfoliative Cheilitis Induced by Sodium Lauryl Sulfate: a Case Report.

    Science.gov (United States)

    Thongprasom, Kobkan

    2016-06-01

    This paper reports on the results of a case study of a 19-year-old female who presented to the Oral Medicine clinic with a chief complaint of scaly and peeling lips. The lesions had persisted on her lips for more than 7 years and were refractory to previous treatment. Her physician's diagnosis was contact dermatitis. We diagnosed this patient as having exfoliative cheilitis (EC). A patch test using the toothpaste containing sodium lauryl sulfate (SLS) was positive and the patient discontinued using it. Instead, she started using a toothpaste not containing SLS. One year after treating her lesions with hydrogen peroxide mouthwash 1% and glycerin borax, a gradual improvement was observed until returning to normal. Glycerin borax was safe, low cost and simple to use in treatment of refractory exfoliative cheilitis. SLS may have been a precipitating factor in EC in this case.

  17. Glycerin Borax Treatment of Exfoliative Cheilitis Induced by Sodium Lauryl Sulfate: a Case Report

    Directory of Open Access Journals (Sweden)

    Kobkan Thongprasom

    2016-01-01

    Full Text Available This paper reports on the results of a case study of a 19-year-old female who presented to the Oral Medicine clinic with a chief complaint of scaly and peeling lips. The lesions had persisted on her lips for more than 7 years and were refractory to previous treatment. Her physician’s diagnosis was contact dermatitis. We diagnosed this patient as having exfoliative cheilitis (EC. A patch test using the toothpaste containing sodium lauryl sulfate (SLS was positive and the patient discontinued using it. Instead, she started using a toothpaste not containing SLS. One year after treating her lesions with hydrogen peroxide mouthwash 1% and glycerin borax, a gradual improvement was observed until returning to normal. Glycerin borax was safe, low cost and simple to use in treatment of refractory exfoliative cheilitis. SLS may have been a precipitating factor in EC in this case.

  18. Performance and carcass characteristics of dairy steers fed diets containing crude glycerin

    Directory of Open Access Journals (Sweden)

    Raylon Pereira Maciel

    Full Text Available ABSTRACT The objective of the study was to assess the effects of including 0, 79.8, 159.8, and 240.0 g kg-1 crude glycerin in the total diet dry matter on the 84 days feedlot performance, nutrient digestibility, blood parameters, and carcass characteristics of crossbred dairy steers. Experimental diets were composed of 98.5 g kg-1 of sorghum silage and 901.5 g kg-1 of concentrate. Twenty-four crossbred dairy steers (337.3±39.8 kg body weight and 15 months of age were distributed in a completely randomized design with four treatments and six replicates. The intake and digestibility of the dry matter and nutrients were not altered by including crude glycerin in the diet. Crude glycerol levels did not affect the final weight (430.2 kg, daily weight gain (1.38 kg day-1, total weight gain (97.2 kg, hot carcass weight (218.9 kg, cold carcass weight (215.2 kg, hot carcass yield (0.50 kg 100 kg-1 BW, longissimus dorsi area (62.86 cm², subcutaneous fat thickness (4.05 mm, and carcass physical composition. Concentrations of serum glucose, triglycerides, total cholesterol, high-density lipoprotein cholesterol, and creatinine were not altered by including crude glycerin in the diet. Crude glycerin can be added to high concentrate diet up to 240 g kg-1 without changing the animal performance, apparent digestibility of nutrients, the main carcass characteristics, and blood parameters of finishing crossbred dairy steers.

  19. A Randomized Controlled Trial of Glycerin Suppositories During Phototherapy in Premature Neonates.

    Science.gov (United States)

    Butler-O'Hara, Meggan; Reininger, Ann; Wang, Hongyue; Amin, Sanjiv B; Rodgers, Nathan J; D'Angio, Carl T

    To determine if glycerin suppositories were effective in reducing total duration of phototherapy in premature neonates. We hypothesized that glycerin suppositories would have no effect on phototherapy duration or total serum bilirubin levels. Prospective randomized controlled double-blinded trial. Level IV NICU. Neonates born between 30 weeks, 0 days and 34 weeks, 6 days gestational age who developed physiologic hyperbilirubinemia needing phototherapy. Neonates were randomized to the no-suppository group or to the suppository group. Neonates were randomized to receive glycerin suppositories every 8 hours while under phototherapy or to a sham group. The primary outcome was total hours of phototherapy. Secondary outcomes included peak total serum bilirubin levels, time from start to discontinuation of phototherapy, rate of decline in bilirubin levels, repeat episodes of phototherapy, and number of stools while the neonates received phototherapy. A total of 39 neonates were assigned to the no-suppository group and 40 to the suppository group. Withholding suppositories was not inferior to providing suppositories. The total hours of phototherapy were not longer (i.e., noninferior) among neonates not provided suppositories (61 ± 53 hours) than among those given suppositories (72 ± 49 hours). There were no differences in peak bilirubin levels, rate of bilirubin decline, or repeat episodes of phototherapy. Routine use of glycerin suppositories among preterm neonates who receive phototherapy does not affect bilirubin levels or phototherapy duration. Copyright © 2017 AWHONN, the Association of Women’s Health, Obstetric and Neonatal Nurses. Published by Elsevier Inc. All rights reserved.

  20. Methodology for full comparative assessment of direct gross glycerin combustion in a flame tube furnace

    Energy Technology Data Exchange (ETDEWEB)

    Maturana, Aymer Yeferson; Pagliuso, Josmar D. [Dept. of Mechanical Engineering. Sao Carlos School of Engineering. University of Sao Paulo, Sao Carlos, SP (Brazil)], e-mails: aymermat@sc.usp.br, josmar@sc.usp.br

    2010-07-01

    This study is to develop a methodology to identify and evaluate the emissions and heat transfer associated to combustion of gross glycerin a by-product of the Brazilian biodiesel manufacture process as alternative energy source. It aims to increase the present knowledge on the matter and to contribute to the improvement of the economic and environmental perspective of biodiesel industry. This methodology was considered to be used for assessment of gross glycerin combustion from three different types of biodiesel (bovine tallow, palm and soy). The procedures for evaluation and quantification of emissions of sulphur and nitrogen oxides, total hydrocarbons, carbon monoxide, carbon dioxide, and acrolein were analyzed, described and standardized. Experimental techniques for mutagenic and toxic effects assessment of gases similarly were analyzed and standardized, as well as the calorific power, the associate heat transfer and fundamentals operational parameters. The methodology was developed, using a full-instrumented flame tube furnace, continuous gas analyzers, a chromatograph, automatic data acquisition systems and other auxiliary equipment. The mutagenic and toxic effects of the study was based on Tradescantia clone KU-20, using chambers of intoxication and biological analytical techniques previously developed and others were specially adapted. The benchmark for the initial set up was based on the performance evaluation of the previous equipment tested with diesel considering its behavior during direct combustion. Finally, the following factors were defined for the combustion of crude glycerin, configurations of equipment types, operational parameters such as air fuel ratio adiabatic temperature and other necessary aspect for successful application of the methodology. The developed and integrated methodology was made available to the concern industry, environmental authorities and researchers as procedures to access the viability of gross glycerin or similar fuels as

  1. A double-blind, randomized study comparing pure chromated glycerin with chromated glycerin with 1% lidocaine and epinephrine for sclerotherapy of telangiectasias and reticular veins.

    Science.gov (United States)

    Kern, Philippe; Ramelet, Albert-Adrien; Wutschert, Robert; Mazzolai, Lucia

    2011-11-01

    Chromated glycerin (CG) is an effective, although painful, sclerosing agent for telangiectasias and reticular leg veins treatment. To determine pain level and relative efficacy of pure or one-third lidocaine-epinephrine 1% mixed chromated glycerin in a prospective randomized double-blind trial. Patients presenting with telangiectasias and reticular leg veins on the lateral aspect of the thigh (C(1A) or (S) E(P) A(S) P(N1) ) were randomized to receive pure CG or CG mixed with one-third lidocaine-epinephrine 1% (CGX) treatment. Lower limb photographs were taken before and after treatment and analyzed by blinded expert reviewers for efficacy assessment (visual vein disappearance). Patients' pain and satisfaction were assessed using visual analogue scales. Data from 102 of 110 randomized patients could be evaluated. Patient pain scores were significantly higher when pure CG was used than with CGX (psclerotherapy pain without affecting efficacy when treating telangiectasias and reticular leg veins. © 2011 by the American Society for Dermatologic Surgery, Inc.

  2. Feeding behavior, microbial efficiency, and nitrogen balance of Nellore heifers supplemented with crude glycerin

    Directory of Open Access Journals (Sweden)

    Gonçalo Mesquita da Silva

    2016-09-01

    Full Text Available This study aimed to evaluate the inclusion of crude glycerin in diets for Nellore heifers grazing on a Brachiaria brizantha pasture, during the dry season, on urine and plasma urea concentrations, feeding behavior, and microbial protein synthesis. Sixty Nellore heifers with an average initial weight of 285.89 ± 18.74 kg, at approximately 19 ± 2 months of age, were distributed, in a completely randomized design, into the following five treatments with twelve replicates: 0.00, 4.00, 8.00, 12.00, and 16.00% inclusion of crude glycerin in the diet they were fed. Grazing time decreased linearly (P 0.05, averaging 113.73g CP per kg TDN ingested. Plasma nitrogen concentration did not show any effects (P > 0.05, averaging 13.11 mg dL?1. Supplementing heifers during the dry season, at 0.7% BW, using up to 16% crude glycerin in the diet composition, did not elicit positive responses from feeding behavior and had little influence on microbial synthesis.

  3. Generation of biogas using crude glycerin from biodiesel production as a supplement to cattle slurry

    Energy Technology Data Exchange (ETDEWEB)

    Robra, S.; Neto, J. A. Almeida [Departamento de Ciencias Agrarias e Ambientais, Universidade Estadual de Santa Cruz, Rod. Ilheus/Itabuna km 16 s/n, CEP 45662-000 Ilheus, Bahia (Brazil); Serpa da Cruz, R.; de Oliveira, A.M.; Santos, J.V. [Departamento de Ciencias Exatas e Tecnologicas, Universidade Estadual de Santa Cruz, Rod. Ilheus/Itabuna km 16 s/n, CEP 45662-000 Ilheus, Bahia (Brazil)

    2010-09-15

    The influence of crude glycerin on biogas production and methane content of the produced biogas was studied, when added to cattle slurry. The experimental design consisted of 5% wt (Gli 5), 10% wt (Gli 10), and 15% wt (Gli 15) of crude glycerin added to cattle slurry, and one control digester without addition of crude glycerin. Anaerobic digestion was carried out in 4 laboratory size CSTR-type biogas digesters with a working volume of 3 L, in semi-continuous regime at mesophilic conditions, over a period of 10 weeks. The highest biogas yields (825.3 mL g{sup -1} and 825.7 mL g{sup -1}, respectively) relative to mass of volatile compounds added, were produced by the treatments Gli 5 and Gli 10. The control treatment produced 268.6 mL g{sup -1}, whereas the treatment Gli 15 produced 387.9 mL g{sup -1}. This low value was due to the breakdown of the process. Compared to the control, methane contents was increased by 9.5%, 14.3%, and 14.6%, respectively, for the treatments Gli 5, Gli 10, and Gli 15. (author)

  4. Randomized controlled trial: impact of glycerin suppositories on time to full feeds in preterm infants.

    Science.gov (United States)

    Khadr, Sophie N; Ibhanesebhor, Samuel E; Rennix, Connie; Fisher, Hazel E; Manjunatha, Chikkanayakanahalli M; Young, David; Abara, Rosemary C

    2011-01-01

    Feed intolerance delays achievement of enteral feeding in preterm infants. Parenteral nutrition is associated with cholestasis and increased risk of sepsis. Glycerin suppositories have been used to promote gastrointestinal motility and feed tolerance. To investigate whether daily glycerin suppositories (a) reduce the time to full enteral feeding in infants born at suppositories; 28-31(+6) weeks subgroup); controls - no intervention. The same feeding protocol and departmental guidelines for other aspects of neonatal intensive care were used in all subjects. Analysis was by intention to treat. 54 babies were recruited (31 males), 29 randomized to receive suppositories; 48 achieved full enteral feeds. The median (range) time to full feeds was 1.6 days shorter in intervention group babies than controls, but not statistically significant: 7.4 (4.6-30.9) days versus 9.0 (4.4-13.3) days (p = 0.780; 95% confidence interval: -1.917, 2.166). No significant differences were observed in secondary outcomes. Intervention group babies passed their first stool earlier than controls (median: day 2 vs. day 4; p = 0.016). Regular glycerin suppositories did not reduce the time to full enteral feeds in infants born at <32 weeks' gestation in our setting. Copyright © 2011 S. Karger AG, Basel.

  5. Semipurified glycerins on starting piglets feeding‏ (15-30 kg - doi: 10.4025/actascianimsci.v35i2.17264

    Directory of Open Access Journals (Sweden)

    Clodoaldo de Lima Costa Filho

    2013-03-01

    Full Text Available The nutritional value and the performance of piglets fed on diets with semipurified glycerin (SPGV and mixed (SPGM vegetable oil was determined and evaluated. Thirty-two crossbred piglets, allotted in a completely randomized block design, were used in the digestibility trial. Two types of glycerin (SPGV and SPGM and three levels of diet (4, 8 and 12% were studied. The experimental unit consisted of one piglet. Glycerins’ metabolizable energy (ME was estimated by regression of ME (kcal kg-1 intake associated with glycerin vs. glycerin intake (kg. ME as-feed-basis rates were 3,373 for SPGV and 2,932 for SPGM, or rather, the glycerins are highly available energy source for piglets. In the performance trial, 90 piglets were allotted in a completely randomized blocks design in a 2 x 4 + 1 factorial scheme, two glycerins, four levels (3, 6, 9 and 12%, five replicates (pens and two piglets per pen. A control diet with no glycerin (0% was additionally formulated. Since no effect of glycerin inclusion on pig performance occurred, it was feasible to use up to 12% of both types of glycerin on piglets feeding.    

  6. Optimization of the anaerobic co-digestion of pasteurized slaughterhouse waste, pig slurry and glycerine

    OpenAIRE

    Rodríguez-Abalde, Ángela; Flotats Ripoll, Xavier; Fernández García, Belén

    2016-01-01

    The feasibility of co-digestion of blends of two different animal by-products (pig manure and pasteurized slaughterhouse waste) and recovered glycerine was studied in mesophilic conditions. Experiments were performed in a lab-scale CSTR along 490 days, with a hydraulic retention time of 21–33 days and with a step-wise increased organic loading rate, by adding and/or changing the wastes ratio, from 0.8 to 3.2 kgCOD m-3 d-1. The best methane production rate (0.64 Nm3CH4 m-3 d-1) represented an ...

  7. Effects of glycerol on the metabolism of broilers fed increasing glycerine levels

    OpenAIRE

    Romano,GG; Menten,JFM; Freitas,LW; Lima,MB; Pereira,R; Zavarize,KC; Dias,CTS

    2014-01-01

    This study evaluated the metabolic response of broilers fed diets containing increasing crude glycerine levels in two bioassays. Birds were house in metabolic cages, and were distributed according to a completely randomized experimental design with five treatments of 4 replicates each (1st assay: 5 birds/ cage; 2nd assay: 1-20 days = 8 birds/ cage, and 21-42 days = 4 birds/cage). Treatments consisted of a control diet based on corn and soybean meal, and four other diets containing 2.5%, 5.0%,...

  8. Synthesis and characterization of Al2O3 obtained from the polymeric precursor method using glycerin as a poly alcohol

    International Nuclear Information System (INIS)

    Elicker, C.; Gaier, M.; Almeida, S.R.; Vieiraaa, B.M.; Ratmann, C.W.R.; Pereira, C.M.P. de; Cava, S.S.; Egea, J.J.

    2014-01-01

    In this study, calcium aluminate was synthesized using glycerin to replace ethylene glycol in the polymeric precursor method. The resulting resin was pre-calcined in a muffle at 300 °C for 2 h and the resulting material was calcined at 900 °C for 2 h. The powders were analyzed by XRD, SEM and EDX, TEM, Micro-Raman and IR. The results demonstrated the possibility of using glycerin as an alternative to ethylene glycol in the polymeric precursor method. (author)

  9. Optimization of the anaerobic co-digestion of pasteurized slaughterhouse waste, pig slurry and glycerine.

    Science.gov (United States)

    Rodríguez-Abalde, Ángela; Flotats, Xavier; Fernández, Belén

    2017-03-01

    The feasibility of co-digestion of blends of two different animal by-products (pig manure and pasteurized slaughterhouse waste) and recovered glycerine was studied in mesophilic conditions. Experiments were performed in a lab-scale CSTR along 490days, with a hydraulic retention time of 21-33days and with a step-wise increased organic loading rate, by adding and/or changing the wastes ratio, from 0.8 to 3.2kg COD m -3 d -1 . The best methane production rate (0.64Nm 3 CH4 m -3 d -1 ) represented an increment of 2.9-fold the initial one (0.22Nm 3 CH4 m -3 d -1 with pig manure solely). It was attained with a ternary mixture composed, in terms of inlet volatile solids, by 35% pig slurry, 47% pasteurized slaughterhouse waste and 18% glycerine. This blend was obtained through a stepwise C/N adjustment: this strategy led to a more balanced biodegradation due to unstressed bacterial populations through the performance, showed by the VFA-related indicators. Besides this, an improved methane yield (+153%) and an organic matter removal efficiency (+83%), regarding the digestion of solely pig slurry, were attained when the C/N ratio was adjusted to 10.3. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Glycerin purification using asymmetric nano-structured ceramic membranes from production of waste fish oil biodiesel

    Science.gov (United States)

    Maghami, M.; Sadrameli, S. M.; Shamloo, M.

    2018-02-01

    Biodiesel is an environmental friendly alternative liquid transportation fuel that can be used in diesel engines without major modifications. The scope of this research work is to produce biodiesel from waste fish oil and its purification from the byproducts using a ceramic membrane. Transesterification of waste fish oil was applied for the biodiesel production using methanol in the presence of KOH as a catalyst. Effect of catalyst weight percent, temperature and methanol to oil molar ratio (MR) on the biodiesel yield have been studied and the results show that highest methyl ester yield of 79.2% has been obtained at 60 °C, MR: 6 and 1% KOH. The produced biodiesel purified by a ceramic membrane. Membrane flux and glycerin removal at different operating conditions such as temperature, trans-membrane pressures and cross flow velocities have been measured. Glycerin purity by membrane method is 99.97% by weight at the optimum condition. The highest membrane flux occurred at 50 °C temperature, 1 bar pressure and 3 m/s velocity.

  11. Dry matter digestibility and metabolizable energy of crude glycerines originated from palm oil using fed rooster assay

    Directory of Open Access Journals (Sweden)

    Astiari Tia Legawa

    2017-07-01

    Full Text Available A study was conducted to determine the dry matter digestibility, gross energy (GE, the nitrogen-corrected apparent metabolizable energy (AMEn, and the nitrogen-corrected true metabolizable energy (TMEn of two crude glycerine from two different sources. The first crude glycerine (CG1 was from a large scale biodiesel producer with high content of glycerol (89.49% and low content of crude fat (1.73%, meanwhile the second crude glycerine (CG2 was from a medium scale biodiesel producer with lower content of glycerol than CG1 (38.36% and high content of crude fat (23.63%. Fed rooster assay based on Sibbald (1976 was used in the experiment. The experimental feed consisted of ground corn and three levels of crude glycerine (0, 10, and 20%. Twenty four Hisex brown roosters were housed in metabolic cages. Roosters were force fed with 30 g experimental feed, after 24 hours of fasting. Excreta collection was performed for two days while the roosters were fasting again. The content values of GE, AMEn, and TMEn of CG1 were 4065.18, 2926.59, and 3068.73 kcal kg-1 and for CG2 were 5928.09, 4010.11, and 4054.52 kcal kg, respectively.

  12. Methane production from cattle manure supplemented with crude glycerin from the biodiesel industry in CSTR and IBR.

    Science.gov (United States)

    Castrillón, L; Fernández-Nava, Y; Ormaechea, P; Marañón, E

    2013-01-01

    The aim of the present research work was to optimise biogas production from cattle manure by adding crude glycerin from the biodiesel industry. For this purpose, 6%v/v crude glycerin (the optimum amount according to previous research) was added to ground manure and the mixture was sonicated to enhance biodegradability prior to anaerobic co-digestion at 55 °C. Two different reactors were used: continuously stirred (CSTR) and induced bed (IBR). The methanol and pure glycerin contents of the crude glycerin used in this study were 5.6% and 49.4% (w/w), respectively. The best results when operating in CSTR were obtained for an organic loading rate (OLR) of 5.4 kg COD/m(3) day, obtaining 53.2m(3) biogas/t wet waste and 80.7% COD removal. When operating in IBR, the best results were obtained for an OLR of 6.44 kg COD/m(3)day, obtaining 89.6% COD removal and a biogas production of 56.5m(3)/t wet waste. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. The production of paper soaps from coconut oil and Virgin Coconut Oil (VCO) with the addition of glycerine as plasticizer

    Science.gov (United States)

    Widyasanti, Asri; Miracle Lenyta Ginting, Anastasia; Asyifani, Elgina; Nurjanah, Sarifah

    2018-03-01

    Hand washing with soap is important because it is proven to clean hands from germs and bacteria. The paper soapswere made from coconut oil and virgin coconut oil (VCO) with the addition of glycerin as a plasticizer. The aims of this research were to determine both formulation of paper soap using coconut oil and VCO based with addition of glycerin, and to determine the quality of the paper soapswhich is a disposable hand soap. This research used laboratory experimental method using descriptive analysis. The treatments of this research were treatment A (paper soap without the addition of glycerin), treatment B (paper soap with the addition of glycerin 10% (w/w)), treatment C (paper soap with the addition of glycerin 15% (w/w)), treatment D (paper soap with the addition of glycerin of 20% (w/w)). Parameters tested were moisture content, stability of foam, pH value, insoluble material in ethanol, free alkali content, unsaponified fat, antibacterial activity test, and organoleptic test. The result of physicochemical characteristics for bothcoconut oil-paper soap and VCO-paper soap revealed that treatment C (the addition of glycerin 15% (w/w) was the best soap formulation. Coconut Oil papersoap 15% w/w glicerin had water content 13.72%, the content of insoluble material in ethanol 3.93%, the content of free alkali 0.21%, and the content of unsaponified fat 4.06%, pH value 10.78, stability of foam 97.77%, and antibacterial activity against S. aureus 11.66 mm. Meanwhile, VCO paper soap 15% w/w glicerin had the value of water content of 18.47%, the value stability of foam of 96.7%, the pH value of 10.03, the value of insoluble material in ethanol of 3.49%, the value of free alkali content 0.17%, the value of unsaponified fat 4.91%, and the value of inhibition diameter on the antibacterial activity test 15.28 mm. Based on Mandatory Indonesian National Standard of solid soap SNI 3532:2016 showed that both of paper soap had not been accorded with SNI 3532:2016, unless the

  14. Recycling of waste vegetable oil biodiesel and glycerine : social enterprise feasibility study

    International Nuclear Information System (INIS)

    2005-12-01

    This study examined the feasibility of recycling waste vegetable oil into biodiesel fuel as part of a social enterprise spearheaded by the Centre de sante communautaire in Sudbury. The enterprise proposed the collection of waste vegetable oil from local restaurants for refinement into biodiesel fuel as well as glycerine byproducts. The study included reviews of legal issues related to the project as well as details of community consultation processes. Target participants were also identified. The biodiesel industry was briefly reviewed along with details of the biodiesel manufacturing process. The study determined that 2 permanent employees will be required to run the biodiesel project. Initial staffing for the first year of the project was estimated at 4 full-time equivalent participants. Equipment and capital purchases for the first year of operation were estimated at $75,000. Total funds for startup of the project were estimated at $140,000. Budgets were supplied to the year 2009. 34 refs., 2 tabs., 5 figs

  15. Economic viability of crude glycerin in diets for lambs finished in feedlot

    Directory of Open Access Journals (Sweden)

    Mauriceia Costa Carvalho Barros

    2015-02-01

    Full Text Available The aim was to evaluate the economic viability of increasing levels of crude glycerin (CG in diets for finishing lambs. The trial was carried out at Southwest State University of Bahia, Itapetinga-BA. Twenty five crossbred, Santa Inês x Dorper, with 24 ± 2,0 kg, were housed in individual pens. The experimental design was completely randomized with five treatments and five replications. Treatments consisted of increasing levels of dietary CG (0, 2.65, 5.33, 8.06 and 10.84% and the roughage used was the Tifton 85 hay. Diets were formulated to meet the nutritional requeriments, aiming a gain of 200 g day-1. The analysis was based on use of economic indicators Net Present Value (NPV and Internal Rate of Return (IRR. The animals dry matter intake decreased linearly (P0.05 on performance and meat production results. None of the treatments showed economic viability.

  16. Histological evaluation of bovine tunica albuginea as biomaterial conserved in 98% glycerin and in 0.625% glutaraldehyde

    Directory of Open Access Journals (Sweden)

    Leticia Leal Oliveira

    2015-12-01

    Full Text Available ABSTRACT. Oliveira L.L., Barata J.S., Silva A.V.P., Caravalho E.C.Q., Nunes L.C. & Abílio E.J. [Histological evaluation of bovine tunica albuginea as biomaterial conserved in 98% glycerin and in 0.625% glutaraldehyde.] Avaliação histológica da túnica albugínea bovina como biomaterial conservada em glicerina a 98% e em glutaraldeído a 0,625%. Revista Brasileira de Medicina Veterinária, 37(4:309-315, 2015. Departamento de Medicina Veterinária, Universidade Federal do Espírito Santo, Alto Universitário s/n, Guararema, Alegre, ES 29500-000, Brasil. E-mail: leticialealolive@hotmail.com Biomaterials have long been studied in reconstructive surgery, both natural and synthetic origin. It can be used as support to host tissue cells development and an efficient bed of stem cells for tissue engineering and regeneration of tissues and organs. The aim of this study was to evaluate the tunica albuginea as biomaterial preserved in glycerin 98% and glutaraldehyde 0.625% and analyze its integrity for use in grafting therapy by microscopic examinations. Tunica albuginea were obtained from healthy adults crossbred cattle from slaughterhouse, tunicas albugineas were preserved in 98% glycerin and 0.625% glutaraldehyde for a period of 30 days at least. Tunica albuginea was fixed in 10% formalin, histologically processed and stained by hematoxylin-eosin, Masson’s trichrome and red picrosisrius polarization. Macroscopically there was a difference in the texture and color of tunica albuginea and in glutaraldehyde group were more firm and thick. Microscopic evaluation revealed that both the glycerin and the glutaraldehyde can be used as conservation medium in function of preserving the basic architecture tissue of the tunica albuginea, however, the glycerin was more efficient preservation of cellular structures. Histochemical techniques have highlighted the collagen and elastic fibers present in tunicas albugineas and highlight the predominance of type I

  17. Effects of dietary inclusion of high concentrations of crude glycerin on meat quality and fatty acid profile of feedlot fed Nellore bulls.

    Directory of Open Access Journals (Sweden)

    Eric H C B van Cleef

    Full Text Available Crude glycerin, the main by-product of biodiesel production, can replace dietary energy sources, such as corn. The objective of this study was to evaluate the inclusion of up to 30% of crude glycerin in dry matter (DM of the total diets, and its effects on meat quality parameters of feedlot Nellore bulls. Thirty animals (227.7 ± 23.8 kg body weight; 18 months old were housed in individual pens and fed 5 experimental diets, containing 0, 7.5, 15, 22.5 or 30% crude glycerin (DM basis. After 103 d (21 d adaptation animals were slaughtered and the Longissimus muscle was collected. The characteristics assessed were chemical composition, fatty acid profile, cholesterol, shear force, pH, color, water-holding capacity, cooking loss and sensory properties. The increasing inclusion of crude glycerin in the diets did not affect the chemical composition of the Longissimus muscle (P > 0.10. A quadratic effect was observed when levels of crude glycerin were increased, on the concentration of pentadecanoic, palmitoleic and eicosenoic fatty acids in meat (P < 0.05, and on the activity of the delta-9 desaturase 16 and delta-9 desaturase 18 enzymes (P < 0.05. The addition of crude glycerin increased the gamma linolenic fatty acid concentration (P < 0.01, and altered the monounsaturated fatty acids in Longissimus muscle of animals (Pquad. < 0.05. Crude glycerin decreased cholesterol content in meat (P < 0.05, and promoted higher flavor score and greasy intensity perception of the meat (P < 0.01. The inclusion of up to 30% crude glycerin in Nellore cattle bulls`diets (DM basis improves meat cholesterol and sensory attributes, such as flavor, without affecting significantly the physical traits, the main fatty acid concentrations and the chemical composition.

  18. Analytical control of an esterification batch reaction between glycerine and fatty acids by near-infrared spectroscopy

    International Nuclear Information System (INIS)

    Blanco, Marcelo; Beneyto, Rafael; Castillo, Miguel; Porcel, Marta

    2004-01-01

    Near-infrared spectroscopy was used to control an esterification reaction between glycerine and middle- or long-chain fatty acids performed in a laboratory-scale reactor. The process involves the initial formation of monoglycerides, which is followed by that of di- and triglycerides as well as transesterification. Establishing the end point of the process is critical with a view to ensuring that the end product will have the composition required for its intended use. PLS calibration was applied to industrial and laboratory-scale batch samples, and laboratory samples were additionally used to extend calibration ranges and avoid correlation between the concentration of the batch samples. In this way, PLS calibration models for glycerine, fatty acids, water, and mono-, di- and triglycerides, were constructed. The proposed method allows the reaction to be monitored in real time, thereby avoiding long analysis times, excessive reagent consumption and the obtainment of out-of-specification products

  19. Antimicrobial effect of Satureja bachtiarica extracts aqueous, ethanol, methanol and glycerin on streptococcus pyogenes, pseudomonas aeruginosa and staphylococcus epidermidis

    OpenAIRE

    Maryam Heidari Sureshjani; Farideh Tabatabaei Yazdi; Ali Mortazavi; Fakhri Shahidi; Behrooz Alizadeh Behbahani

    2013-01-01

    The Iranian medicinal plants, such as Satureja bachtiarica have been utilized as traditional medicines by the indigenous people of Chaharmahal va Bakhtiari in Iran. In this study, Satureja bachtiarica were dried in suitable condition (in shadow) after extraction with watery, ethanol 96 %, methanol 96% and 20% glycerin antimicrobial effect of extract were determined by “screening antimicrobial activity” and “disk agar diffusion test” in 10, 20, 30 and 40 mg/ml concentration of the extract agai...

  20. Antimicrobial Effect of Aqueous, Ethanol, Methanol and Glycerin Extracts of Satureja bachtiarica on Streptococcus pyogenes, Pseudomonas aeruginosa and Staphylococcus epidermidis

    OpenAIRE

    Maryam Heidari-Sureshjani; Faride Tabatabaei-Yazdi; Behrooz Alizadeh-Behbahani; Ali Mortazavi

    2015-01-01

    Background: The Iranian medicinal plants, such as Satureja bachtiarica have been utilized as traditional medicines by the indigenous people of Chaharmahal and Bakhtiari in Iran. Objectives: According to biologically active compounds and traditional use of the Satureja bachtiarica, seem that this plant has significant antimicrobial effects. Materials and Methods: In this experimental study, Satureja bachtiarica after extraction with watery, ethanol 96%, methanol 96% and 20% glycerin anti...

  1. Carcass characteristics of feedlot lambs fed crude glycerin contaminated with high concentrations of crude fat.

    Science.gov (United States)

    Lage, J F; Paulino, P V R; Pereira, L G R; Duarte, M S; Valadares Filho, S C; Oliveira, A S; Souza, N K P; Lima, J C M

    2014-01-01

    Thirty non-castrated male lambs with 20±2.3 kg average body weight (BW) were randomly assigned to five treatments consisted of different dietary concentrations of crude glycerin (CG; 0, 3, 6, 9 and 12% on DM basis) to evaluate the effects on performance, carcass and meat quality traits. A quadratic effect was observed for performance (P=0.04), final BW (P0.05) on carcass pH neither on shear-force, cooking loss and ether extract content in longissimus. The inclusion of CG tended to reduce the Zn content in meat (P=0.09). The data suggests that CG (36.2% of glycerol and 46.5% of crude fat) may be used in diets of finishing lambs with concentrations up to 3% without negative effects on performance and main carcass traits. Moreover, inclusion of CG seems to not affect quality and safety of meat for human consumption. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. Slowly digestible properties of lotus seed starch-glycerine monostearin complexes formed by high pressure homogenization.

    Science.gov (United States)

    Chen, Bingyan; Jia, Xiangze; Miao, Song; Zeng, Shaoxiao; Guo, Zebin; Zhang, Yi; Zheng, Baodong

    2018-06-30

    Starch-lipid complexes were prepared using lotus seed starch (LS) and glycerin monostearate (GMS) via a high-pressure homogenization process, and the effect of high pressure homogenization (HPH) on the slow digestion properties of LS-GMS was investigated. The digestion profiles showed HPH treatment reduced the digestive rate of LS-GMS, and the extent of this change was dependent on homogenized pressure. Scanning electron microscopy displayed HPH treatment change the morphology of LS-GMS, with high pressure producing more compact block-shape structure to resist enzyme digestion. The results of Gel-permeation chromatography and Small-angle X-ray scattering revealed high homogenization pressure impacted molecular weight distribution and semi-crystalline region of complexes, resulting in the formation of new semi-crystalline with repeat unit distance of 16-18 nm and molecular weight distribution of 2.50-2.80 × 10 5  Da, which displayed strong enzymatic resistance. Differential scanning calorimeter results revealed new semi-crystalline lamellar may originate from type-II complexes that exhibited a high transition temperature. Copyright © 2018 Elsevier Ltd. All rights reserved.

  3. Properties of lotus seed starch-glycerin monostearin complexes formed by high pressure homogenization.

    Science.gov (United States)

    Chen, Bingyan; Zeng, Shaoxiao; Zeng, Hongliang; Guo, Zebin; Zhang, Yi; Zheng, Baodong

    2017-07-01

    Starch-lipid complexes were prepared using lotus seed starch (LS) and glycerin monostearate (GMS) via a high pressure homogenization (HPH) process, and the effect of HPH on the physicochemical properties of LS-GMS complexes was investigated. The results of Fourier transform infrared spectroscopy and complex index analysis showed that LS-GMS complexes were formed at 40MPa by HPH and the complex index increased with the increase of homogenization pressure. Scanning electron microscopy displayed LS-GMS complexes present more nest-shape structure with increasing homogenization pressure. X-ray diffraction and differential scanning calorimetry results revealed that V-type crystalline polymorph was formed between LS and GMS, with higher homogenization pressure producing an increasingly stable complex. LS-GMS complex inhibited starch granules swelling, solubility and pasting development, which further reduced peak and breakdown viscosity. During storage, LS-GMS complexes prepared by 70-100MPa had higher Avrami exponent values and lower recrystallization rates compared with native starch, which suggested a lower retrogradation trendency. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Impact of stirring speed, glycerin and sodium chloride concentrations on photoprotective nanoemulsions

    Directory of Open Access Journals (Sweden)

    Débora Granemann e Silva

    2014-09-01

    Full Text Available New technologies that improve the physical as the sensory properties of sunscreens can help to increase its continued use and impact on health. The use of nanoemulsions in the development of photoprotective vehicles is an advantage, since nanostructured components may have superior properties regarding their performance when compared to conventional products. The advantages of using nanobiotechnology in manufacture of cosmetic and dermatological formulations arise from the protection of compounds from chemical or enzymatic degradation, from the control of their release, and also to the prolonged retention time of cosmetic ingredients in the stratum corneum. Thus, this study aimed to evaluate the impact of stirring speed and of glycerin and sodium chloride concentrations in the development and effectiveness of a nanoemulsion containing ethylhexyl methoxycinnamate and benzophenone-3. The results of statistical analyses regarding the impact of the variables in the process of nanoemulsion development showed that these parameters affect the phase inversion temperature (PIT. However, this did not affect the particle size and the photoprotective efficacy in vitro.

  5. Mixed crude glycerin in laying hen diets: live performance and egg quality and fatty acid profile

    Directory of Open Access Journals (Sweden)

    CRA Duarte

    2014-12-01

    Full Text Available This study evaluated the performance and the quality and fatty acid profile of eggs from laying hens fed diets containing mixed crude glycerin (MCG; 80% vegetable fat + 20% animal fat. A total of 240 39-week-old Hy-Line W36 laying hens were distributed according to a completely randomized experimental design into six treatments consisting of graded MCG dietary inclusion levels (0, 1.5, 3.0, 4.5, 6.0, and 7.5%, with five replicates of eight birds each. Feed intake linearly decreased (p<0.05 with increasing MCG inclusion levels. The percentages of myristic, palmitic, and α-linolenic acids in the eggs linearly decreased as MCG dietary levels increased (p<0.05, while α-linoleic acid, polyunsaturated fatty acids (PUFA and ω-6/ω-3 ratio linearly increased. Excreta moisture linearly increased with increasing levels of MCG inclusion (p<0.05. MCG may be included in up to 7.5% in layer feeds without impairing performance or egg quality, but levels up to 5.54% reduce SFA egg content. However, the inclusion of MCG in layer diets increases ω-6/ω-3 ratio in the eggs.

  6. "The blood pressure and dermal sensitivity effects of Nylon hollow fiber releasing Glycerin Trinitrate in vivo "

    Directory of Open Access Journals (Sweden)

    "Ostad SN

    2002-09-01

    Full Text Available In order to improve patient's compliance in taking glycerine trinitrate (GTN nylon hollow fiber which has been successfully used for release of chlorhexidine diacetate and levonorgestrel was employed to make nylon hollow fiber releasing GTN. Hollow nylon fibres of external diameter 0.63 mm, 75 mm long with an internal capacity of 16 μl, were filled with GTN (190 mg/ml in 70% ethanol (v/v or vehicle alone and the ends were heat-sealed. The fibers were then immersed in 10 ml of 0.9% (w/v saline in a separating funnel. The GTN release pattern from fiber, the effect of the product on blood pressure and its potential dermal toxicity were assessed. The release of GTN from the fibres was approximately 2.7 μg/min when the fibres contained 16 mg of drug. The results showed that the amount of GTN within the single fibre was enough to reduce blood pressure significantly, while it did not show significant dermal toxicity. It is concluded that GTN fiber, if used as monofilament, is not an alternative method for GTN delivery.

  7. Evaluation of dairy sheep lambs supplemented with crude glycerin conveyed in water during pregnancy and lactation

    Directory of Open Access Journals (Sweden)

    Hemilly Cristina Menezes Sá

    2017-08-01

    Full Text Available The aim of this study was to evaluate the influence of crude glycerin (CG suplementation in sheep diets during pregnancy and transition period. Twenty-four Lacaune x East Friesian genotypes sheep were randomly assigned to four treatments. Diet was composed of roughage: tifton hay, and standard concentrate for the categories, being these similar among the treatments, whereas the CG differed for the supplements in (zero, 1,5, 3,0 and 4,5% of dry matter being It added to the animals’ drinking water. The sheep received supplementation during all pregnancy and lactation. Dry matter intake during gestation was reduced with the higher supplementation of CG in the animals’ drinking water, presenting a linear decreasing response and remaining until delivery. Throughout lactation, the variable presented a linear behavior with the supplementation of CG on the eighteenth day of this phase, after a quadratic behavior was observed until the end of the evaluated period. The beta-hydroxybutyrate and non-esterified fatty acids levels were not influenced by CG supplementation throughout the gestation period. CG suplementation conveyed in water did not affect negatively milk production and composition.

  8. The Influence of a Humectant on the Retention by Humans of Solanesol from Cigarette Smoke (Part 2, Glycerin

    Directory of Open Access Journals (Sweden)

    Moldoveanu SC

    2014-12-01

    Full Text Available Two common humectants are used as additives in the cigarette manufacturing process, propylene glycol (PG and glycerin. The humectants may influence the deposition of cigarette smoke in the human respiratory tract by affecting the hygroscopic properties and growth of smoke particles. This study examines the influence of glycerin addition on the retention of solanesol by smokers. The influence of PG addition has been previously reported (7. The first cigarette used in the study (control was a commercially available brand containing no additives in the blend (with a measured level of glycerin of 0.19%. The other cigarette (test had an identical tobacco blend to the control, but had 2.3% added glycerin. The construction of the cigarette with 2.3% glycerin (test was selected to match as closely as possible the ‘tar’ (as measured by Federal Trade Commission regimen, pressure drop (open and closed, and nicotine level of the commercial cigarette (control. Twelve smokers evaluated both products. The sample collection was performed using three cigarettes smoked within one hour. Each human subject smoked the control cigarette and then the test cigarette in two separate sessions. The exhaled smoke was collected using a vacuum assisted procedure designed to avoid strain in exhaling, and solanesol was analyzed using an high performance liquid chromatography (HPLC technique. The cigarette butts from the smokers were collected and also analyzed for solanesol. The results obtained for the cigarette butts from the smokers were used to calculate the level of solanesol in the smoke delivered to the human subject, based on calibration curves. These curves were generated separately by analyzing the solanesol in smoke and in the cigarette butts obtained by machine smoking under different puffing regimes. Knowing the levels of delivered amount of solanesol and that in the exhaled smoke it was possible to calculate the retention of this compound from mainstream

  9. Effect of supplementary glycerin on milk composition and heat stability in dairy goats

    Directory of Open Access Journals (Sweden)

    Deela Thoh

    2017-12-01

    Full Text Available Objective This experiment was studied the effects of various levels of crude glycerin (CG in dairy goat diet on daily intake, milk yield, milk composition, some physical properties and some quality changes of goat milk after sterilization. Methods Twelve 75% Saanen dairy goats (body weight = 49±3 kg; days in milk = 60±12 d were randomly assigned in a completely randomized design to evaluate the effects of three experimental diets consisting of 0%, 5%, and 10% CG (dry matter basis which were formulated to meet or exceed the nutrient requirements of goats. Experimental dairy goats were evaluated for feed and milk yield. Milk samples were analyzed for their composition, including fatty acids, casein profile, fat globule size, and color, and were sterilized to evaluate milk heat stability. Results There were no significant differences between 0% and 5% CG treatments infeed. Increasing CG supplementation from 0% to 5% increased milk yield from 2.38±0.12 to 2.64±0.23 kg/goat/d. In addition, milk samples from 5% CG treatment had the highest total solids, fat content and lactose content, and largest fat globule size. Increasing CG to 10% resulted in a decrease in milk fat. After sterilizing at 116°C, F0 = 3 min, goat milk samples from 5% CG treatment had slightly higher sediment content and comparatively higher degree of browning. Conclusion Considering milk yield, milk fat content and quality of sterilized milk, 5% CG supplementation in a total mixed ration has a potential for implementation in dairy goats.

  10. Microbiological evaluation of anatomical organs submitted to glycerinization and freeze-drying techniques

    Directory of Open Access Journals (Sweden)

    Marianna Justo

    2016-06-01

    Full Text Available Alternatives conservation techniques are being requested with the proposal of formaldehyde substitution. Formaldehyde results in excessive anatomical specimens' weight and it can cause serious health problems to the manipulator, such as cancer. However, it provides an efficient germicide and fungicide action depending on concentration. The substitute techniques are glicerinization and freeze-drying which have advantages such as non-production of smells, lightness of the organs and dispenses the use of fixatives in conservation. As well as both intrinsic and extrinsic factors interfere in microbial growth, microbiological analyzes are essential to detect possible deteriorative microorganisms in organs and concluding effectively the technique used. Formalinized, glycerinated and freeze-drying organs were collected in three different times which were intercalated by two months, except formalinization that had one evaluation. The procedure required the use of sterilized swabs wetted in peptone water and molds measuring 5,0 cm x 10,0 cm positioned on two different piece's local resulting in 100 cm2 of area, to spread plate of total moulds, mesophiles (except in freeze-drying, psychrophilic (only in freeze-drying and Pseudomonas sp (except in formalinization. All the plates were counted and compared between each technique's evaluations by variance analyzes. Both alternatives techniques resulted in zero or in very low microbial quantity to cause health problems as well as it preserve pieces morphology. All values of all analyzes resulted below 1/ml, showing that glicerinization and freeze-drying techniques are so as efficient as formaldehyde. Keywords: Organs conservation, Anatomical techniques, Microbiology, Microbial growth

  11. A prospective randomized single blind trial of Fleet phosphate enema versus glycerin suppositories as preparation for flexible sigmoidoscopy.

    Science.gov (United States)

    Underwood, D; Makar, R R; Gidwani, A L; Najfi, S M; Neilly, P; Gilliland, R

    2010-03-01

    This study compared the efficacy and patient acceptability of two methods of bowel preparation for flexible sigmoidoscopy. Patients attending for outpatient flexible sigmoidoscopy were prospectively randomized to receive one Fleet ready-to-use enema or 2 x 4 g glycerin suppositories, 2 h preprocedure. Patient and endoscopist questionnaires were used to compare the outcomes. From November 2000 to August 2001, 203 (male = 95; female = 108) patients were randomized. Patient data available for 163 patients (enema = 93; suppository = 70) revealed: ease of use (enema = 52; suppository = 25; P suppositories.

  12. Co-digestion of crude glycerin associated with cattle manure in biogas production in the State of Paraná, Brazil

    Directory of Open Access Journals (Sweden)

    Felix Augusto Pazuch

    2017-05-01

    Full Text Available The addition of different concentrations of crude glycerin, associated with cattle manure, on the volumetric production of biogas is analyzed. Different concentrations of crude glycerin (2, 4 and 6% m m-1 were added as supplement in anaerobic co-digestion of dairy cattle waste, in laboratory batch biodigesters (3.5 L usable volume. The biodigesters were operated under mesophilic conditions (30ºC, with 30-day hydraulic retention time (HRT. Total solids (TS, volatile solids (VS and chemical oxygen demand (COD were analyzed to determine the efficiency of the process in the removal of organic matter and its effect on biogas production. The addition of 4% glycerin provided a larger production of biogas, approximately 9.307 mL. The efficiency in COD removal decreased in treatments with glycerin, with highest reduction (68% in the control treatment. There was a 90 and 118% increase respectively for Gli4 and Gli6% treatments. VS reductions Gly 0, Gly 2, Gly 4 and Gly 6% treatments were 18.17, 61.60, 24.36 and 44.83%, for the respective treatments.

  13. Effects of feeding condensed distillers solubles and crude glycerin alone or in combination on finishing beef cattle performance, carcass characteristics, and in vitro fermentation.

    Science.gov (United States)

    Two experiments were conducted to evaluate the effects of feeding condensed distillers solubles (DS) and crude glycerin alone or in combination on performance of finishing beef cattle and in vitro fermentation. In both experiments, dietary treatments consisted of a steam flaked corn (SFC) based diet...

  14. Obtaining polyester from glycerin for synthesis of polyurethanes; Obtencao de poliester a partir da glicerina para sintese de poliuretanas

    Energy Technology Data Exchange (ETDEWEB)

    Breves, Rodolfo A.; Ghesti, Grace F.; Sales, Maria J.A., E-mail: eu_sou_o_rodolfo@hotmail.com [Universidade de Brasilia (LabPol/UnB), DF (Brazil). Laboratorio de Pesquisa em Polimeros; Silva, Jessica S.; Coelho, Paulo V.M.; Lopes, Roseany V.V. [Universidade de Brasilia (UnB), DF (Brazil). Faculdade do Gama; Brioude, Michel M. [Freiburg University (Germany)

    2014-07-01

    The use of renewable resources has been increasing, due to the development of materials that have viable applications that are environmentally friendly. In this paper, a polyester was synthesized from glycerin, with the addition of adipic acid in a molar ratio of 1: 1.5, with dilauryl tin catalyst, which was added in proportions of 1 to 3% obtained PUs from castor oil (Ricinus communis) and MDI (diphenyl methane diisocyanate). The materials were characterized by infrared spectroscopy (FTIR), nuclear magnetic resonance {sup 1}H NMR, thermogravimetry (TG) and derivative thermogravimetry (DTG). The reaction for obtaining the polyester was confirmed by FTIR, the absorption band between 1708-1730 cm{sup -1} and {sup 1}H NMR, in the region 1.4 to 1.8 ppm and 2.2 to 2.6 ppm. The thermal decomposition of polyester occurred with temperature above 300 ° C. PUs showed similar thermal stability. (author)

  15. The influence of temperature on the rheology of biodiesel and on the biodiesel-glycerin-ethanol blend - doi: 10.4025/actascitechnol.v34i1.8067

    Directory of Open Access Journals (Sweden)

    Andrés José Cocato Steluti

    2011-11-01

    Full Text Available After transesterification reaction, biodiesel and glycerin (the resulting co-product, coupled to reaction excesses and impurities, make up two distinct phases that must be separated. The use of ethanol as a transesterificating agent impairs the above-mentioned separation due to the greater affinity of ethyl esters (biodiesel from ethanol to glycerin. Current research provides an analysis of the influence of temperature on the rheology of biodiesel and the bio-diesel-glycerin-ethanol blend. Rheology behavior is highly important not merely in issues involving, for instance, discharging and pumping, but also as a factor that should be evaluated within the process of separation of the biodiesel-glycerin phases by decantation and centrifugation.

  16. Fabrication of porous ethyl cellulose microspheres based on the acetone-glycerin-water ternary system: Controlling porosity via the solvent-removal mode.

    Science.gov (United States)

    Murakami, Masahiro; Matsumoto, Akihiro; Watanabe, Chie; Kurumado, Yu; Takama, Masashi

    2015-08-01

    Porous ethyl cellulose (EC) microspheres were prepared from the acetone-glycerin-water ternary system using an oil/water (O/W)-type emulsion solvent extraction method. The O/ W type emulsion was prepared using acetone dissolved ethyl cellulose as an oil phase and aqueous glycerin as a water phase. The effects of the different solvent extraction modes on the porosity of the microspheres were investigated. The specific surface area of the porous EC microspheres was estimated by the gas adsorption method. When the solvent was extracted rapidly by mixing the emulsion with water instantaneously, porous EC microspheres with a maximum specific surface area of 40.7±2.1 m2/g were obtained. On the other hand, when water was added gradually to the emulsion, the specific surface area of the fabricated microspheres decreased rapidly with an increase in the infusion period, with the area being 25-45% of the maximum value. The results of an analysis of the ternary phase diagram of the system suggested that the penetration of water and glycerin from the continuous phase to the dispersed phase before solidification affected the porosity of the fabricated EC microspheres.

  17. Effects of crude glycerin from waste vegetable oil supplementation on feed intake, ruminal fermentation characteristics, and nitrogen utilization of goats.

    Science.gov (United States)

    Chanjula, Pin; Pongprayoon, Sahutaya; Kongpan, Sirichai; Cherdthong, Anusorn

    2016-06-01

    This experiment was evaluation of the effects of increasing concentrations of crude glycerin from waste vegetable oil (CGWVO) in diets on feed intake, digestibility, ruminal fermentation characteristics, and nitrogen balance of goats. Four crossbred male (Thai Native × Anglo Nubian) goats, with an average initial body weight (BW) of 31.5 ± 1.90 kg, were randomly assigned according to a 4 × 4 Latin square design. The dietary treatments contained 0, 2, 4, and 6 % of dietary dry matter (DM) of CGWVO. Based on this experiment, there were significantly different (P > 0.05) among treatment groups regarding DM intake and digestion coefficients of nutrients (DM, OM, CP, EE, NDF, and ADF), which goats receiving 6 % of CGWVO had lower daily DMI and nutrient intake than those fed on 0, 2, and 4 % of CGWVO. Ruminal pH, NH3-N, and blood urea nitrogen (BUN) concentration were unchanged by dietary treatments, except that for 6 % of CGWVO supplementation, NH3-N, and BUN were lower (P goats. This study was a good approach in exploiting the use of biodiesel production from waste vegetable oil for goat production.

  18. Anaerobic co-digestion of crude glycerin and starch industry effluent Codigestão anaeróbia de glicerina bruta e efluente de fecularia

    Directory of Open Access Journals (Sweden)

    Andrea C. Larsen

    2013-04-01

    Full Text Available The Brazil's Biodiesel Production and Use Program introduces biodiesel in the Brazilian energy matrix, bringing along the perspective of a growth of the glycerin offer, co-product generated in the proportion of 10 kg for each 100 L of biodiesel. The aim of this study was to evaluate the addition of crude glycerin in the anaerobic digestion of cassava starch industry effluent (cassava wastewater, in a horizontal semi-continuous flow reactor of one phase in laboratory scale. It was used a reactor with a 8.77 L of useful volume, a medium support for corrugated conduit of polyvinyl chloride (PVC, temperature of 261 ºC, fed with cassava wastewater and glycerin, with hydraulic detention times of 4 and 5 days and increasing volumetric organic load of 3.05; 9.32; 14.83 and 13.59 g COD L-1 d-1, obtained with the addition of glycerin at 0; 2; 3 and 2% (v/v, respectively. The average removal efficiencies of TS and TVS were decreasing from the addition of glycerin to the cassava wastewater, averaging 81.19 to 55.58% for TS and 90.21 to 61.45% for TVS. The addition of glycerin at 2% increased the biogas production compared to the control treatment, reaching 1.979 L L-1 d-1. The biogas production as a function of the consumed COD was higher for the control treatment than for the treatments with addition of glycerin, which indicates lower conversion of organic matter into biogas.O Programa Nacional de Produção e Uso do Biodiesel introduziu o biodiesel na matriz energética brasileira, trazendo a perspectiva de aumento da oferta de glicerina, coproduto gerado na proporção de 10 kg para cada 100 L de biodiesel. O objetivo principal deste trabalho foi avaliar a adição de glicerina bruta na digestão anaeróbia de efluente de indústria de fécula de mandioca (manipueira, em reator de fluxo semicontínuo horizontal de uma fase, em escala de laboratório. Foi utilizado um reator com volume útil de 8,77 L, meio suporte em eletroduto corrugado de policloreto

  19. Effects of crude glycerin from waste vegetable oil in diets on performance and carcass characteristics of feedlot goats

    Science.gov (United States)

    2018-01-01

    Objective This experiment was conducted to investigate the effects of crude glycerin from waste vegetable oil (CGWVO) on performance, carcass traits, meat quality, and muscle chemical composition. Methods Twenty-four crossbred (Thai Native×Anglo Nubian) uncastrated male goats (16.8± 0.46 kg body weight [BW]) were assigned to a completely randomized design and subjected to four experimental diets containing 0%, 2%, 4%, and 6% of CGWVO (63.42% of glycerol and 47.78% of crude fat) on a dry matter (DM) basis. The diets were offered ad libitum as total mixed rations twice daily. The feed intake, feeding behavior, growth performance, carcass and meat traits, and muscle chemical composition were evaluated. Results Based on this experiment, there were significant differences (p>0.05) among groups regarding DM intake, growth performance, and carcass traits where goats receiving 6% of CGWVO had lower daily DM intake, growth performance, and carcass traits than those fed on 0%, 2%, and 4% of CGWVO. There were no effects of CGWVO on carcass length, carcass width, Longissimus muscle (LM) area, Warner-Bratzler shear force, pH and color of LM at 45 min after slaughter, as well as on other carcass cut and muscle chemical composition. Conclusion In conclusion, the addition of up to 4% of DM in the diets for crossbred finishing goats seems to be the most interesting strategy, since it promotes greatest animal performance. Moreover, this study was a suitable approach to exploit the use of biodiesel production from waste vegetable oil for goat production. PMID:28830128

  20. Effects of crude glycerin from waste vegetable oil in diets on performance and carcass characteristics of feedlot goats.

    Science.gov (United States)

    Chanjula, Pin; Cherdthong, Anusorn

    2018-04-01

    This experiment was conducted to investigate the effects of crude glycerin from waste vegetable oil (CGWVO) on performance, carcass traits, meat quality, and muscle chemical composition. Twenty-four crossbred (Thai Native×Anglo Nubian) uncastrated male goats (16.8± 0.46 kg body weight [BW]) were assigned to a completely randomized design and subjected to four experimental diets containing 0%, 2%, 4%, and 6% of CGWVO (63.42% of glycerol and 47.78% of crude fat) on a dry matter (DM) basis. The diets were offered ad libitum as total mixed rations twice daily. The feed intake, feeding behavior, growth performance, carcass and meat traits, and muscle chemical composition were evaluated. Based on this experiment, there were significant differences (p>0.05) among groups regarding DM intake, growth performance, and carcass traits where goats receiving 6% of CGWVO had lower daily DM intake, growth performance, and carcass traits than those fed on 0%, 2%, and 4% of CGWVO. There were no effects of CGWVO on carcass length, carcass width, Longissimus muscle (LM) area, Warner-Bratzler shear force, pH and color of LM at 45 min after slaughter, as well as on other carcass cut and muscle chemical composition. In conclusion, the addition of up to 4% of DM in the diets for crossbred finishing goats seems to be the most interesting strategy, since it promotes greatest animal performance. Moreover, this study was a suitable approach to exploit the use of biodiesel production from waste vegetable oil for goat production.

  1. Effects of crude glycerin from waste vegetable oil in diets on performance and carcass characteristics of feedlot goats

    Directory of Open Access Journals (Sweden)

    Pin Chanjula

    2018-04-01

    Full Text Available Objective This experiment was conducted to investigate the effects of crude glycerin from waste vegetable oil (CGWVO on performance, carcass traits, meat quality, and muscle chemical composition. Methods Twenty-four crossbred (Thai Native×Anglo Nubian uncastrated male goats (16.8± 0.46 kg body weight [BW] were assigned to a completely randomized design and subjected to four experimental diets containing 0%, 2%, 4%, and 6% of CGWVO (63.42% of glycerol and 47.78% of crude fat on a dry matter (DM basis. The diets were offered ad libitum as total mixed rations twice daily. The feed intake, feeding behavior, growth performance, carcass and meat traits, and muscle chemical composition were evaluated. Results Based on this experiment, there were significant differences (p>0.05 among groups regarding DM intake, growth performance, and carcass traits where goats receiving 6% of CGWVO had lower daily DM intake, growth performance, and carcass traits than those fed on 0%, 2%, and 4% of CGWVO. There were no effects of CGWVO on carcass length, carcass width, Longissimus muscle (LM area, Warner-Bratzler shear force, pH and color of LM at 45 min after slaughter, as well as on other carcass cut and muscle chemical composition. Conclusion In conclusion, the addition of up to 4% of DM in the diets for crossbred finishing goats seems to be the most interesting strategy, since it promotes greatest animal performance. Moreover, this study was a suitable approach to exploit the use of biodiesel production from waste vegetable oil for goat production.

  2. Quasi-solid-state dye-sensitized solar cells from hydrophobic poly(hydroxyethyl methacrylate/glycerin)/polyaniline gel electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Li, Qinghua [National Defence Key Discipline Laboratory of Light Alloy Processing Science and Technology, Nanchang Hangkong University, Nanchang 330063 (China); Tang, Qunwei, E-mail: tangqunwei@hotmail.com [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Chen, Haiyan [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Xu, Haitao; Qin, Yuancheng [National Defence Key Discipline Laboratory of Light Alloy Processing Science and Technology, Nanchang Hangkong University, Nanchang 330063 (China); He, Benlin, E-mail: blhe@ouc.edu.cn [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Liu, Zhichao; Jin, Suyue; Chu, Lei [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China)

    2014-04-01

    Hydrophobic poly(hydroxyethyl methacrylate/glycerin) [poly(HEMA/GR)] gel with a three-dimensional (3D) framework was successfully fabricated and employed to integrate with polyaniline (PANi). The resultant poly(HEMA/GR)/PANi gel electrolyte exhibited interconnective porous structure for holding I{sup −}/I{sub 3}{sup −}, giving a similar conduction mechanism and ionic conductivity to that of liquid system but a much enhanced retention of I{sup −}/I{sub 3}{sup −} redox couple. Fourier transform infrared spectroscopy, X-ray diffraction patterns, cyclic voltammograms as well as electrochemical impedance spectroscopy were employed to evaluate the molecular structure, crystallinity, and the electrochemical behaviors, showing that the combination of PANi with poly(HEMA/GR) caused a lower charge-transfer resistance and higher electrocatalytic activity for the I{sub 3}{sup −}/I{sup −} redox reaction in the gel electrolyte. An efficiency of 6.63% was recorded from the quasi-solid-state DSSC assembled with the poly(HEMA/GR)/PANi gel electrolyte at 100 mW cm{sup −2}. - Graphical abstract: A poly(HEMA/GR)/PANi gel electrolyte is synthesized through in situ polymerization of PANi in 3D framework of poly(HEMA/GR) hydrophobic hydrogel. The recorded ionic conductivity and electrochemical performances are significantly enhanced by integrating with PANi The resultant overall photo-to-electric conversion efficiency is 6.63%. The high ionic conductivity, along with good electrolyte retention ability, reasonable DSSC performance, low cost, simple and scalable synthesis procedure, and competitive cost, promises the electrolyte to find applications in quasi-solid-state DSSCs. - Highlights: • Poly(HEMA/GR) was employed to combine with PANi in the 3D framework. • The conductivity and electrochemical performances were enhanced. • The conversion efficiency of the quasi-solid-state DSSC was 6.63%.

  3. Thermoplastic polyolefins as formaldehyde free binders in highly filled lignocellulosic panel boards: using glycerine as a processing aid in kenaf fiber polypropylene boards

    Directory of Open Access Journals (Sweden)

    Anand Ramesh Sanadi

    2008-12-01

    Full Text Available A new technique was developed to make highly loaded (up to 95% formaldehyde free natural fiber boards. The purpose of the paper is to report a broad study on 85% kenaf boards using linear thermoplastic polymers as the binder in preparing the boards to determine if these materials have potential in commercial applications by comparing them to other commercial materials. In these materials, linear thermoplastic polymer chains act as an adhesive and the product resembles a typical wood based panel (e.g., phenol formaldehyde fiber board. The process involved the use of small amount of glycerine in the fiber to enhance processibility in a thermo-kinetic mixer followed by hot pressing. In this paper, we report the properties of 85% by weight kenaf fiber boards using polypropylene as the adhesive. A maleated polypropylene was used to improve the adhesion and stress transfer between the adhesive and kenaf fiber. The addition of 2% by weight of glycerine based on the dry weight of kenaf fiber resulted in the best properties of the boards. Differential scanning calorimetric studies suggested that the glycerine had a little effect on the percent crystallinity of the matrix. Dynamic mechanical tests of the 85% boards showed some differences compared to conventional 60% by weight kenaf-PP composites. The 85% kenaf boards had a flexural strength of 75 MPa and a flexural modulus of 6.8 GPa with a specific gravity of 1.24. These properties are comparable to standard formaldehyde free high density hardboards with flexural strengths of 48.3 MPa and flexural modulus of 5.5 GPa, and a specific gravity of 1.28. This paper gives a broad overview of an initial study of these new materials.

  4. Development of various composition multicomponent chitosan/fish collagen/glycerin 3D porous scaffolds: Effect on morphology, mechanical strength, biostability and cytocompatibility.

    Science.gov (United States)

    Ullah, Saleem; Zainol, Ismail; Chowdhury, Shiplu Roy; Fauzi, M B

    2018-05-01

    The various composition multicomponent chitosan/fish collagen/glycerin 3D porous scaffolds were developed and investigated the effect of various composition chitosan/fish collagen/glycerin on scaffolds morphology, mechanical strength, biostability and cytocompatibility. The scaffolds were fabricated via freeze-drying technique. The effects of various compositions consisting in 3D scaffolds were investigated via FT-IR analysis, porosity, swelling and mechanical tests, and effect on the morphology of scaffolds investigated microscopically. The biostability and cytocompatibility tests were used to explore the ability of scaffolds to use for tissue engineering application. The average pore sizes of scaffolds were in range of 100.73±27.62-116.01±52.06, porosity 71.72±3.46-91.17±2.42%, tensile modulus in dry environment 1.47±0.08-0.17±0.03MPa, tensile modulus in wet environment 0.32±0.03-0.14±0.04MPa and biodegradation rate (at day 30) 60.38±0.70-83.48±0.28%. In vitro culture of human fibroblasts and keratinocytes showed that the various composition multicomponent 3D scaffolds were good cytocompatibility however, the scaffolds contained high amount of fish collagen excellently facilitated cell proliferation and adhesion. It was found that the high amount fish collagen and glycerin scaffolds have high porosity, enough mechanical strength and biostability, and excellent cytocompatibility. Copyright © 2018 Elsevier B.V. All rights reserved.

  5. Triacrylate of glycerin synthesis and use in network polymer;Sintese do triacrilato de glicerina e seu uso como agente de ligacao cruzada

    Energy Technology Data Exchange (ETDEWEB)

    Morita, Reinaldo Y.; Zawadzki, Sonia F.; Barbosa, Ronilson V., E-mail: yomorita1@hotmail.co [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil). Centro Politecnico

    2009-07-01

    The goal of this work was the synthesis and characterization of a new cross linker: the glyceryl triacrylate. The synthesis was done by an esterification reaction between glycerin and acrylic acid and the product, called GA, was characterized by infrared and nuclear magnetic resonance (NMR- 1a) spectroscopy. The behavior was analysed after a copolymerization with methyl methacrylate monomer (MMA). It was also prepared the PMMA and GA homopolymers. The addition of glycerin triacrylate up to 2 % in the MMA monomer changed the solubility of the copolymer. This one became insoluble in organic solvents in which the pure linear poly(methyl methacrylate) was soluble. Thermal analysis showed that the addition of 2% GA didn't change the Tg value of the PMMA pure, but the GA homopolymer showed a Tg value equal to 180 C, lower than expected. It seems that GA product is working as cross linker, but some insaturation links did not react. They remain as pendent groups, causing the Tg lowering. The results suggest that the new product can be used as cross linker for the application in acrylic polymers. (author)

  6. Inverse break-through investigation on uranium isotope separation in the system Fe(III) water-glycerine solution-U(IV) cathionic resin

    International Nuclear Information System (INIS)

    Murgulescu, Sanda; Calusaru, A.

    1977-01-01

    When a solution containing ferric ions passes on cationic resin in U(IV) form, the substitution of uranium by iron is preceded by oxydation of U(IV) to U(VI). During the contact of U(VI) in solution with U(IV) in resin, an exchange reaction occurs, in which 235 U is slightly concentrated in solution and 238 U in resin phase. Since increase of temperature accelerates the exchange reaction, the apparent thermodynamic values of the exchange reaction were calculated, by taking into account the variation of the apparent equilibrium constant as a function of the reciprocal value of the temperature. The corresponding thermodynamic values in both pure aqueous and water-glycerine solution are: ΔH 0 =6.45 cal.mol -1 and ΔS 0 =21.6x10 -3 cal. 0 K -1 . The use of glycerine containing solutions offers the important advantage to increase the stability versus hydrolysis of the ferric ions even at higher temperature

  7. Effects of partial replacement of maize in the diet with crude glycerin and/or soyabean oil on ruminal fermentation and microbial population in Nellore steers.

    Science.gov (United States)

    Granja-Salcedo, Yury Tatiana; Duarte Messana, Juliana; Carneiro de Souza, Vinícius; Lino Dias, Ana Veronica; Takeshi Kishi, Luciano; Rocha Rebelo, Lucas; Teresinha Berchielli, Telma

    2017-11-01

    The objective of this study was to determine whether a combination of crude glycerin (CG) and soyabean oil (SO) could be used to partially replace maize in the diet of Nellore steers while maintaining optimum feed utilisation. Eight castrated Nellore steers fitted with ruminal and duodenal cannulas were used in a double 4×4 Latin square design balanced for residual effects, in a factorial arrangement (A×B), when factor A corresponded to the provision of SO, and factor B to the provision of CG. Steers feed SO and CG showed similar DM intake, DM, organic matter and neutral-detergent fibre digestibility to that of steers fed diets without oil and without glycerine (P>0·05). Both diets with CG additions reduced the acetate:propionate ratio and increased the proportion of iso-butyrate, butyrate, iso-valerate and valerate (Pdiets containing SO had less total N excretion (Pdiet generated a greater ruminal abundance of Prevotella, Succinivibrio, Ruminococcus, Syntrophococcus and Succiniclasticum. Archaea abundance (P=0·002) and total ciliate protozoa were less in steers fed diets containing SO (P=0·011). CG associated with lipids could be an energy source, which is a useful strategy for the partial replacement of maize in cattle diets, could result in reduced total N excretion and ruminal methanogens without affecting intake and digestibility.

  8. Anaerobic co-digestion cassava wastewater and crude glycerin for removal of COD and solid; Co-digestao anaerobica de manipueira e glicerina bruta para remocao de DQO e solidos

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Jefferson L.G.; Guerra Junior, Joao B. [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil)], E-mail: j.lg11@yahoo.com.br; Gomes, Simone D.; Mallmann, Larissa S. [Universidade Estadual do Oeste do Parana (CCET/PGEAGRI/UNIOESTE), Cascavel, PR (Brazil). Dept. de Recursos Hidricos e Saneamento Ambiental

    2012-11-01

    To be discarded into the environment, cassava wastewater, generated during the processing of the cassava root, needs to be dealt with trying to reduce its organic load and total solids, harmful to water bodies. As for crude glycerin, a byproduct of biodiesel production, need alternatives to its destination, because the cost to its purification is often not feasible, preventing its use by pharmaceutical and food industries. In this study we chose to anaerobic digestion to treat manipueira assessing the behavior of the reactor with the addition of glycerin. The reactor was constructed of PVC with 60cm long, 20cm in diameter and a volume of 8.38 L, and HRT was 5 days. Three treatments were applied: T1, only manipueira, T2 with 0.25% glycerol and T3, with 0.50%. The three treatments showed a great reduction of organic load (above 90%) and higher with the addition of 0.25% crude glycerine. The highest mean removal of solids and total volatile solids occurred in treatment with 0.50% crude glycerine, being 84.18% and 91.41% respectively. (author)

  9. The Effects of Stereotactic Cerebroventricular Administration of Albumin, Mannitol, Hypertonic Sodium Chloride, Glycerin and Dextran in Rats with Experimental Brain Edema.

    Science.gov (United States)

    Ates, Tuncay; Gezercan, Yurdal; Menekse, Guner; Turkoz, Yusuf; Parlakpinar, Hakan; Okten, Ali Ihsan; Akyuva, Yener; Onal, Selami Cagatay

    2017-01-01

    To evaluate the effects of cerebroventricular administration of hyperoncotic/hyperosmotic agents on edematous brain tissue in rats with experimental head trauma. The study included 54 female Sprague-Dawley rats with weights ranging between 200 and 250 g. Six experimental groups were examined with each group containing 9 rats. All rats were exposed to head trauma, and treatment groups were administered 2 µl of one of the drugs (albumin, mannitol, hypertonic sodium chloride (NaCl), glycerin and dextran) 6, 12 and 24 hours after the trauma via the cerebroventricular route and using a stereotactic device. Rats were sacrificed 48 hours after the trauma, and brain tissues were extracted without damage. Biochemical analyses including reduced glutathione (GSH), nitric oxide (NO), malondialdehyde (MDA), tumor necrosis factor alpha (TNF-α), and interleukin 1 beta (IL-1β) were performed on the injured left hemisphere. Compared with the control group, the albumin, mannitol, 3% NaCl and glycerin treatment groups revealed dramatic increases in GSH levels (p < 0.001). Levels of MDA, which is the end-product of brain edema and lipid peroxidation, failed to show a statistically significant decrease, but there was a decreasing trend observed in the inter-group comparisons. NO levels were also decreased in the 3% NaCl treatment group. An analysis of TNF-α and IL-1β, two proinflammatory cytokines associated with the trauma, revealed that IL-1β decreased significantly in all treatment groups (p=0.001), whereas no significant difference was detected in TNF-α levels. Cerebroventricular administration of hyperoncotic/hyperosmotic agents provides substantial effects on the treatment of brain edema.

  10. Effects of glycerin concentration in steam-flaked corn-based diets with supplemental yellow grease on performance and carcass characteristics of finishing beef steers.

    Science.gov (United States)

    Buttrey, E K; Luebbe, M K; McCollum, F T; Cole, N A; MacDonald, J C; Hales, K E

    2015-07-01

    Forty-eight individually fed crossbred steers (initial BW = 381 ± 7.61 kg) were used to determine the effects of glycerin (GLY) concentration in steam-flaked corn (SFC)-based diets with added yellow grease on animal performance and carcass characteristics. Glycerin was included at 0, 2.5, 5, and 10% dietary DM replacing SFC. A completely randomized design was used with steers as the experimental unit, and the model included the fixed effects of diet. Contrast statements were used to determine linear and quadratic effects of GLY inclusion. Final BW and DMI were not affected (P > 0.27) by GLY concentration. Average daily gain and G:F based on live BW did not differ as GLY level increased in the diet from 0 to 10% of DM (P > 0.33). Carcass-adjusted final BW and carcass-adjusted G:F were also not affected by GLY concentration (P > 0.22); however, carcass-adjusted ADG tended to respond quadratically by decreasing from 2.5 to 5% GLY inclusion and increasing thereafter (P = 0.10). Calculated dietary NEm and NEg did not differ as GLY increased in the diet (P > 0.37). Hot carcass weight tended to respond quadratically, decreasing from 2.5 to 5% GLY and increasing thereafter (P = 0.10). Likewise, dressing percentage tended to respond quadratically by decreasing from 2.5 to 5% GLY inclusion and increasing to 10% GLY inclusion (P = 0.09). Fat thickness decreased linearly as GLY inclusion increased in the diet (P 0.21). Calculated yield grade (YG) decreased linearly as GLY increased in the diet from 0 to 10% of DM (P = 0.04). Based on our results, there was no animal performance benefit for replacing SFC with GLY in diets containing yellow grease, and the only change in carcass merit was a slight improvement in YG.

  11. Effect of glycerin and formic acid in the efficiency of deposit on Zn-Ni, obtained by electrodeposition; Efeito da glicerina e do acido formico na eficiencia de deposito da liga Zn-Ni, obtido atraves de eletrodeposicao

    Energy Technology Data Exchange (ETDEWEB)

    Pedroza, G.A.G.; Souza, C.A.C.; Lima, L.R.P.A.; Ferreira, D.M. [Universidade Federal da Bahia - Escola Politecnica, BA (Brazil)

    2010-07-01

    Additives are added to the electrodeposition of metal coatings to improve the characteristics of the deposit. However, the objective was to investigate the effect of adding glycerin and formic acid in the deposition efficiency and deposit structure of zinc-nickel alloy obtained by electrodeposition. The depositions were made at a galvanostatic current density of 10 mA/cm{sup 2} to obtain a deposit of about 5 mm in thickness. The deposition efficiency was determined through measures of mass, chemical composition of the deposit in the presence and absence of additives was examined by X-ray Spectrometer Fluorescence (XRF) and surface characterization of coatings was performed by Scanning Electron Microscopy (SEM). The high levels of glycerin (0,07 M) and formic acid (0,26 M) in bath deposition increased the deposition efficiency of around 10% to 12% by mass, respectively. (author)

  12. Gliceroquímica: novos produtos e processos a partir da glicerina de produção de biodiesel Glycerochemistry: new products and processes from glycerin of biodiesel production

    Directory of Open Access Journals (Sweden)

    Claudio J. A. Mota

    2009-01-01

    Full Text Available Glycerol is a byproduct of biodiesel production through transesterification of oils and fat. This article discusses the chemical transformation of glycerol in ethers, acetals and esters of high technological applications, especially in the fuel sector. Glycerol hydrogenolysis, dehydration to acrolein and oxidation are discussed as well, to show the potential use of glycerol for production of plastic monomers. Finally, the article shows other transformations, such as syn gas production, epichloridrin and glycerin carbonate.

  13. A determination of elementary separation factors of isotopes 235U and 238U in the ionic exchange process and of eluents in the water-glycerine system

    International Nuclear Information System (INIS)

    Murgulescu, S.E.

    1977-01-01

    In the experiments focused on uranium isotope separation by ion and chemical exchange, the water-glycerine system was employed. The principle of the method consists in shifting a uranium band along an ion-exchange resin column by means of an eluent. The isotope effect of reactions determining the band heading into the column where complex bands between the metal ion and the ligand form and break up under the resin influence, is determined by the difference in affinity between the two isotopes as against the eluent. The isotope effect in question determines a unit deviation of the equilibrium constant for the classical isotope exchange reaction. Starting from the experimental results obtained, it was concluded that the ion and chemical exchange between the IV and VI valence forms of uranium can be applied to isotope separation in terms of the separation unit. As against the methods that have been applied at present (gaseous scattering, hydro-extracting and the nozzle method), for which every new stage corresponds to a separation elementary factor, several separation elementary factors can be cumulated into a single stage in a chemical and ion exchange unit, by the optimization of the shifting band and length. (author)

  14. A QUASI EXPERIMENTAL STUDY TO EVALUATE EFFECTIVENESS OF GLYCERIN MAGNESIUM SULPHATE DRESSING ON PHLEBITIS AMONG PATIENTS UNDERGOING PERIPHERAL INTRAVENOUS INFUSION IN SELECTED HOSPITAL,VADODARA

    Directory of Open Access Journals (Sweden)

    Ravindra HN, Patel Krupa D

    2015-07-01

    Full Text Available Introduction: Intravenous therapy is indicated for many reasons. A significant number of patients admitted into hospital receive some forms of intravenous therapy through peripheral venous cannula, which is a common procedure carried out in hospital to allow rapid and accurate administration of medication. However, the intravenous cannulation can have undesirable effects, the most of which is phlebitis, which is due to mechanical, chemical or infectious cause. Method: In this study quasi-experimental research approach was used. Non probability purposive sampling technique was used to select the sample from the selected hospital. The research design adopted for the study was pre-test, post-test control group design. In the present study a sample of 60 hospitalised patients and who met the inclusion criteria was selected from the target population. In this study the instruments used are baseline Performa, structured interview schedule to assess the subjective symptoms and observation scale to observe the objective symptoms. Result: In experimental group post test mean score 1.10, SD was 0.71 respectively. In control group post test mean score 2.53, SD was 0.78 respectively. The obtained value 7.454 statistically was significant at 0.001 levels. So research hypothesis was accepted. So there was significant difference between post intervention phlebitis among the experimental group and control group. Discussion: In the research study findings revealed that Glycerin Magnesium sulphate dressing is highly effective in decrease phlebitis level to the patients.

  15. Glycerin-Induced Conformational Changes in Bombyx mori Silk Fibroin Film Monitored by (13)C CP/MAS NMR and ¹H DQMAS NMR.

    Science.gov (United States)

    Asakura, Tetsuo; Endo, Masanori; Hirayama, Misaki; Arai, Hiroki; Aoki, Akihiro; Tasei, Yugo

    2016-09-09

    In order to improve the stiff and brittle characteristics of pure Bombyx mori (B. mori) silk fibroin (SF) film in the dry state, glycerin (Glyc) has been used as a plasticizer. However, there have been very limited studies on the structural characterization of the Glyc-blended SF film. In this study, (13)C Cross Polarization/Magic Angle Spinning nuclear magnetic resonance (CP/MAS NMR) was used to monitor the conformational changes in the films by changing the Glyc concentration. The presence of only 5 wt % Glyc in the film induced a significant conformational change in SF where Silk I* (repeated type II β-turn and no α-helix) newly appeared. Upon further increase in Glyc concentration, the percentage of Silk I* increased linearly up to 9 wt % Glyc and then tended to be almost constant (30%). This value (30%) was the same as the fraction of Ala residue within the Silk I* form out of all Ala residues of SF present in B. mori mature silkworm. The ¹H DQMAS NMR spectra of Glyc-blended SF films confirmed the appearance of Silk I* in the Glyc-blended SF film. A structural model of Glyc-SF complex including the Silk I* form was proposed with the guidance of the Molecular Dynamics (MD) simulation using ¹H-¹H distance constraints obtained from the ¹H Double-Quantum Magic Angle Spinning (DQMAS) NMR spectra.

  16. Toxicity of the main electronic cigarette components, propylene glycol, glycerin, and nicotine, in Sprague-Dawley rats in a 90-day OECD inhalation study complemented by molecular endpoints.

    Science.gov (United States)

    Phillips, Blaine; Titz, Bjoern; Kogel, Ulrike; Sharma, Danilal; Leroy, Patrice; Xiang, Yang; Vuillaume, Grégory; Lebrun, Stefan; Sciuscio, Davide; Ho, Jenny; Nury, Catherine; Guedj, Emmanuel; Elamin, Ashraf; Esposito, Marco; Krishnan, Subash; Schlage, Walter K; Veljkovic, Emilija; Ivanov, Nikolai V; Martin, Florian; Peitsch, Manuel C; Hoeng, Julia; Vanscheeuwijck, Patrick

    2017-11-01

    While the toxicity of the main constituents of electronic cigarette (ECIG) liquids, nicotine, propylene glycol (PG), and vegetable glycerin (VG), has been assessed individually in separate studies, limited data on the inhalation toxicity of them is available when in mixtures. In this 90-day subchronic inhalation study, Sprague-Dawley rats were nose-only exposed to filtered air, nebulized vehicle (saline), or three concentrations of PG/VG mixtures, with and without nicotine. Standard toxicological endpoints were complemented by molecular analyses using transcriptomics, proteomics, and lipidomics. Compared with vehicle exposure, the PG/VG aerosols showed only very limited biological effects with no signs of toxicity. Addition of nicotine to the PG/VG aerosols resulted in effects in line with nicotine effects observed in previous studies, including up-regulation of xenobiotic enzymes (Cyp1a1/Fmo3) in the lung and metabolic effects, such as reduced serum lipid concentrations and expression changes of hepatic metabolic enzymes. No toxicologically relevant effects of PG/VG aerosols (up to 1.520  mg PG/L + 1.890 mg VG/L) were observed, and no adverse effects for PG/VG/nicotine were observed up to 438/544/6.6 mg/kg/day. This study demonstrates how complementary systems toxicology analyses can reveal, even in the absence of observable adverse effects, subtoxic and adaptive responses to pharmacologically active compounds such as nicotine. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  17. The effect of glycerin solution density and viscosity on vibration amplitude of oblique different piezoelectric MC near the surface in 3D modeling

    Science.gov (United States)

    Korayem, A. H.; Abdi, M.; Korayem, M. H.

    2018-06-01

    The surface topography in nanoscale is one of the most important applications of AFM. The analysis of piezoelectric microcantilevers vibration behavior is essential to improve the AFM performance. To this end, one of the appropriate methods to simulate the dynamic behavior of microcantilever (MC) is a numerical solution with FEM in the 3D modeling using COMSOL software. The present study aims to simulate different geometries of the four-layered AFM piezoelectric MCs in 2D and 3D modeling in a liquid medium using COMSOL software. The 3D simulation was done in a spherical container using FSI domain in COMSOL. In 2D modeling by applying Hamilton's Principle based on Euler-Bernoulli Beam theory, the governing motion equation was derived and discretized with FEM. In this mode, the hydrodynamic force was assumed with a string of spheres. The effect of this force along with the squeezed-film force was considered on MC equations. The effect of fluid density and viscosity on the MC vibrations that immersed in different glycerin solutions was investigated in 2D and 3D modes and the results were compared with the experimental results. The frequencies and time responses of MC close to the surface were obtained considering tip-sample forces. The surface topography of MCs different geometries were compared in the liquid medium and the comparison was done in both tapping and non-contact mode. Various types of surface roughness were considered in the topography for MC different geometries. Also, the effect of geometric dimensions on the surface topography was investigated. In liquid medium, MC is installed at an oblique position to avoid damaging the MC due to the squeezed-film force in the vicinity of MC surface. Finally, the effect of MC's angle on surface topography and time response of the system was investigated.

  18. A comparison of dioctahedral smectite and iodine glycerin cream with topical mouth rinse in treatment of chemotherapy induced oral mucositis: a pilot study.

    Science.gov (United States)

    Lin, Jin-Xiang; Fan, Zu-Yan; Lin, Qu; Wu, Dong-Hao; Wu, Xiang-Yuan; Chen, Yan-Ru; Fang, Heng-Ying; Wu, Dong-Bing; Wen, Jing-Yun; Dong, Min; Ma, Xiao-Kun; Wan, Xiang-Bo

    2015-04-01

    To compare the efficacy of dioctahedral smectite and iodine glycerin (DSIG) cream with topical mouth rinse (composed of saline, gentamicin and Vitamin B12) in treatment of chemotherapy induced oral mucositis (OM). A total of 130 intensive chemotherapy or stem cells transplantation induced OM patients were recruited. Among these patients, 67 patients received topical mouth rinse and 63 patients received DSIG cream treatment. The OM would be treated on the OM appearance and sustained for 5 days. OM severity was measured daily using The American Oncology Nursing Society recommended Oral Assessment Guideline (OAG) score system. Compared with topical mouth rinse treatment, a significant lower OAG score was observed in DSIG cream treated patients. Specifically, the OAG scores were respectively 12.1 ± 1.1, 12.0 ± 1.2, 11.3 ± 1.3 and 10.4 ± 1.3 from day 2 to day 5 in topical mouth rinse treatment subgroup. Correspondingly, the OAG scores were respectively 10.2 ± 1.0, 9.3 ± 0.9, 8.5 ± 0.6 and 8.0 ± 0.2 for DSIG cream treatment subset (all P < 0.05). Importantly, compared with topical mouth rinse treatment, the DSIG cream significantly shortened OM repair time (4.68 ± 0.98 vs. 8.76 ± 1.80 days, P < 0.001). After 5 days treatment, 54 patients (85.7%) obtained complete regression with an OAG score ≤8, and 7 patients (11.1%) had partial regression with an OAG score of 9-10 in DSIG cream treatment subgroup. However, only 2 patients (3.0%) obtained completed regression and 32 patients (47.8%) had partial regression in topical mouth rinse treatment cohort. Moreover, no serious side-effect was observed in both cohorts. Compared with topical mouth rinse, DSIG cream significantly lowered the OAG score and shortened OM duration. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Synthesis and characterization of Al{sub 2}O{sub 3} obtained from the polymeric precursor method using glycerin as a poly alcohol; Sintese e caracterizacao de Al{sub 2}O{sub 3} obtida por meio do metodo dos precursores polimericos utilizando glicerina como polialcool

    Energy Technology Data Exchange (ETDEWEB)

    Elicker, C.; Gaier, M.; Almeida, S.R.; Vieiraaa, B.M.; Ratmann, C.W.R.; Pereira, C.M.P. de; Cava, S.S. [Universidade Federal de Pelotas (UFPel), Pelotas, RS (Brazil); Egea, J.J. [Consejo Superior de Investigaciones Cientificas, Madrid (Spain)

    2014-07-01

    In this study, calcium aluminate was synthesized using glycerin to replace ethylene glycol in the polymeric precursor method. The resulting resin was pre-calcined in a muffle at 300 °C for 2 h and the resulting material was calcined at 900 °C for 2 h. The powders were analyzed by XRD, SEM and EDX, TEM, Micro-Raman and IR. The results demonstrated the possibility of using glycerin as an alternative to ethylene glycol in the polymeric precursor method. (author)

  20. Crude glycerine mixture in diets of broiler chickens (1 to 42 days Glicerina bruta mista na alimentação de frangos de corte (1 a 42 dias

    Directory of Open Access Journals (Sweden)

    Ivan Moreira

    2011-12-01

    Full Text Available Two experiments were conducted to evaluate the effect of inclusion of different levels of crude glycerine mixture in the broilers feeding on performance, carcass yield and carcass composition. 960 broilers were used at 21 days of age distributed in a completely randomized design with six levels of crude glycerine mixture (0; 2; 4; 6; 8 and 10% and five replicates with 32 birds each. In the Experiment 1, for the growth period (22 to 42 days, was a linear effect in the levels of crude glycerine mixture inclusion on feed intake and a quadratic effect for weight gain, average weight and litter dry matter at 42 days old. There was no effect on broiler chicken carcass yield. In the Experiment 2, in the initial period (1 to 21 days, there was an increasing linear effect for feed intake and feed conversion. The same behavior was observed only for feed conversion in the period of 1 to 42 days. For chemical composition analysis of birds were not observed effects for all variables. The litter moisture at 21 and 42 days increased linearly. The utilization of crude glycerine mixture, byproduct of biodiesel production in feed formulation for broilers is possible, however should be better evaluated, for all the nutrients of its composition that could come into the diet balance, making possible to the broilers to have a nice performance.Dois experimentos foram conduzidos com o objetivo de avaliar o efeito da utilização de diferentes níveis de glicerina bruta mista na alimentação de frangos de corte sobre o desempenho, o rendimento de carcaça e a composição química corporal das aves. Foram utilizadas 960 aves da linhagem cobb, distribuídas em delineamento inteiramente casualizado, com seis níveis de inclusão de glicerina bruta mista na dieta (0; 2; 4; 6; 8 e 10% e cinco repetições com 32 aves cada. No experimento I, para o período de crescimento (22 a 42 dias, observou-se efeito linear dos níveis de inclusão de glicerina bruta mista sobre o

  1. The 24-hour skin hydration and barrier function effects of a hyaluronic 1%, glycerin 5%, and Centella asiatica stem cells extract moisturizing fluid: an intra-subject, randomized, assessor-blinded study.

    Science.gov (United States)

    Milani, Massimo; Sparavigna, Adele

    2017-01-01

    Moisturizing products are commonly used to improve hydration in skin dryness conditions. However, some topical hydrating products could have negative effects on skin barrier function. In addition, hydrating effects of moisturizers are not commonly evaluated up to 24 hours after a single application. Hyaluronic acid (HA) and glycerin are very well-known substances able to improve skin hydration. Centella asiatica extract (CAE) could exert lenitive, anti-inflammatory and reepithelialization actions. Furthermore, CAE could inhibit hyaluronidase enzyme activity, therefore prolonging the effect of HA. A fluid containing HA 1%, glycerin 5% and stem cells CAE has been recently developed (Jaluronius CS [JCS] fluid). To evaluate and compare the 24-hour effects of JCS fluid on skin hydration and on transepidermal water loss (TEWL) in healthy subjects in comparison with the control site. Twenty healthy women, mean age 40 years, were enrolled in an intra-subject (right vs left), randomized, assessor-blinded, controlled, 1-day trial. The primary end points were the skin hydration and TEWL, evaluated at the volar surface of the forearm and in standardized conditions (temperature- and humidity-controlled room: 23°C and 30% of humidity) using a corneometer and a vapometer device at baseline, 1, 8 and 24 hours after JCS fluid application. Measurements were performed by an operator blinded for the treatments. Skin hydration after 24 hours was significantly higher ( P =0.001; Mann-Whitney U test) in the JCS-treated area in comparison with the control site. JCS induced a significant ( P =0.0001) increase in skin hydration at each evaluation time (+59% after 1 hour, +48% after 8 hours and +29% after 24 hours) in comparison with both baseline ( P =0.0001) and non-treated control site ( P =0.001). TEWL after 24 hours was significantly lower ( P =0.049; Mann-Whitney U test) in the JCS-treated area in comparison with the control site (13±4 arbitrary units [AU] vs 16±6 AU). JCS fluid

  2. A Paired, Double-Blind, Randomized Comparison of a Moisturizing Durable Barrier Cream to 10% Glycerine Cream in the Prophylactic Management of Postmastectomy Irradiation Skin Care: Trans Tasman Radiation Oncology Group (TROG) 04.01

    Energy Technology Data Exchange (ETDEWEB)

    Graham, Peter H., E-mail: peter.graham@sesiahs.health.nsw.gov.au [Cancer Care Centre, St. George Hospital, Kogarah, New South Wales (Australia); Plant, Natalie; Graham, Jennifer L.; Browne, Lois [Cancer Care Centre, St. George Hospital, Kogarah, New South Wales (Australia); Borg, Martin [Department of Radiation Oncology, Royal Adelaide Hospital (Australia); Capp, Anne [Department of Radiation Oncology, Mater Hospital, Newcastle, New South Wales (Australia); Delaney, Geoff P. [Cancer Care Centre, Liverpool Hospital, Liverpool, New South Wales (Australia); Harvey, Jennifer [Mater Hospital, South Brisbane, Queensland (Australia); Kenny, Lisbeth [Royal Brisbane Hospital, Herston, Queensland (Australia); Francis, Michael [Andrew Love Cancer Centre, Geelong (Australia); Zissiadis, Yvonne [Department of Radiation Oncology, Royal Perth Hospital, Perth (Australia)

    2013-05-01

    Purpose: A previous, unblinded study demonstrated that an alcohol-free barrier film containing an acrylate terpolymer (ATP) was effective in reducing skin reactions compared with a 10% glycerine cream (sorbolene). The different appearances of these products precluded a blinded comparison. To test the acrylate terpolymer principle in a double-blinded manner required the use of an alternative cream formulation, a moisturizing durable barrier cream (MDBC); the study was conducted by the Trans Tasman Radiation Oncology Group (TROG) as protocol 04.01. Methods and Materials: A total of 333 patients were randomized; 1 patient was ineligible and 14 patients withdrew or had less than 7 weeks' observations, leaving 318 for analysis. The chest wall was divided into medial and lateral compartments, and patients were randomized to have MDBC applied daily to the medial or lateral compartment and sorbolene to the other compartment. Weekly observations, photographs, and symptom scores (pain and pruritus) were collected to week 12 or resolution of skin reactions if earlier. Skin dose was confirmed by centrally calibrated thermoluminescent dosimeters. Results: Rates of medial and lateral compartment Common Toxicity Criteria (CTC), version 3, greater than or equal to grade 3 skin reactions were 23% and 41%, but rates by skin care product were identical at 32%. There was no significant difference between MDBC and sorbolene in the primary endpoint of peak skin reactions or secondary endpoints of area-under-the-curve skin reaction scores. Conclusions: The MDBC did not reduce the peak skin reaction compared to sorbolene. It is possible that this is related to the difference in the formulation of the cream compared with the film formulation. Skin dosimetry verification and double blinding are essential for radiation skin care comparative studies.

  3. A Paired, Double-Blind, Randomized Comparison of a Moisturizing Durable Barrier Cream to 10% Glycerine Cream in the Prophylactic Management of Postmastectomy Irradiation Skin Care: Trans Tasman Radiation Oncology Group (TROG) 04.01

    International Nuclear Information System (INIS)

    Graham, Peter H.; Plant, Natalie; Graham, Jennifer L.; Browne, Lois; Borg, Martin; Capp, Anne; Delaney, Geoff P.; Harvey, Jennifer; Kenny, Lisbeth; Francis, Michael; Zissiadis, Yvonne

    2013-01-01

    Purpose: A previous, unblinded study demonstrated that an alcohol-free barrier film containing an acrylate terpolymer (ATP) was effective in reducing skin reactions compared with a 10% glycerine cream (sorbolene). The different appearances of these products precluded a blinded comparison. To test the acrylate terpolymer principle in a double-blinded manner required the use of an alternative cream formulation, a moisturizing durable barrier cream (MDBC); the study was conducted by the Trans Tasman Radiation Oncology Group (TROG) as protocol 04.01. Methods and Materials: A total of 333 patients were randomized; 1 patient was ineligible and 14 patients withdrew or had less than 7 weeks' observations, leaving 318 for analysis. The chest wall was divided into medial and lateral compartments, and patients were randomized to have MDBC applied daily to the medial or lateral compartment and sorbolene to the other compartment. Weekly observations, photographs, and symptom scores (pain and pruritus) were collected to week 12 or resolution of skin reactions if earlier. Skin dose was confirmed by centrally calibrated thermoluminescent dosimeters. Results: Rates of medial and lateral compartment Common Toxicity Criteria (CTC), version 3, greater than or equal to grade 3 skin reactions were 23% and 41%, but rates by skin care product were identical at 32%. There was no significant difference between MDBC and sorbolene in the primary endpoint of peak skin reactions or secondary endpoints of area-under-the-curve skin reaction scores. Conclusions: The MDBC did not reduce the peak skin reaction compared to sorbolene. It is possible that this is related to the difference in the formulation of the cream compared with the film formulation. Skin dosimetry verification and double blinding are essential for radiation skin care comparative studies

  4. Glycerine associated molecules with herbicide for controlling ...

    African Journals Online (AJOL)

    Admin

    Copyright © 2015. Author(s) retain the copyright of this article .... facilitates and assists the cuticular penetration (Banks et al., 2014). A promising ..... Production, consumption, prices, characterization and new trends in combustion. Renew.

  5. Effects of phenol, glycerin and acetic acid on the liver of guinea pigs Efeitos da soluçao de fenol, glicerina e ácido acético em figado de cobaias

    Directory of Open Access Journals (Sweden)

    Rogério Saad-Hossne

    2007-12-01

    Full Text Available PURPOSE: To investigate the histolytic action of a solution composed of phenol, glycerin and acetic acid for irresectable hepatic metastasis. METHODS: Thirty-two (n=32 guinea pigs were randomly distributed into two groups of 16 animals. The animals in group 1 (experimental and group 2 (control were redistributed in two subgroups of eight animals each, according to the day of sacrifice (24 hours and four weeks after injection. All the animals were submitted to median laparotomy, which was followed by the injection of solution E and saline into the livers of subjects in both the experimental and control groups, respectively. The animals were evaluated for biochemical and anatomopathological (liver alterations after 24 hours and four weeks of the experiment. RESULTS: It was observed that solution E produced necrosis limited to the injected area and that hepatic tissue recovery occurred after four weeks with the formation of a small necrosis area. No biochemical parameters were altered either in the experimental or in the control group. CONCLUSION: In view of the obtained results, the possibility of using the proposed solution can be considered in cases of irresectable metastasis.OBJETIVO: Investigar a ação histolítica da solução composta de fenol, glicerina e ácido acético para os casos de metástases hepáticas não ressecáveis. MÉTODOS: Foram utilizadas 32 cobaias, distribuídas, por sorteio, em quatro grupos: experimental (24 horas e quatro semanas e controle (24 horas e quatro semanas; todos os animais foram submetidos a laparotomia mediana e realizada a injeção da solução E (grupo experimental ou solução fisiológica (grupo controle. Foram estudadas as alterações bioquímicas e anatomopatológicas (fígado com 24 horas e quatro semanas de evolução. RESULTADOS: Verificou-se que a solução E produz necrose delimitada à área infiltrada apos 24 horas e que ao final de quatro semanas ocorreu regeneração do tecido hep

  6. Pino ósseo homólogo conservado em glicerina a 98% e hemicerclagem com fio poliglactina 910 na osteossíntese umeral de pombos domésticos Homologous bone pin conserved in glycerin at 98% and hemicerclagem with a thread of poliglactina 910 in humerus osteosyntesis of domestic pigeons

    Directory of Open Access Journals (Sweden)

    Juliano Bolson

    2008-10-01

    Full Text Available O objetivo do presente estudo foi avaliar a utilização de um pino intramedular ósseo homólogo, conservado em glicerina a 98%, associado à hemicerclagem com fio poliglactina 910 na osteossíntese umeral transversa de pombos domésticos (Columba livia. Utilizou-se como pino ósseo a parte distal do tibiotarso, conservado com medula óssea. Foram operados 20 pombos domésticos, adultos, não-sexados e clinicamente sadios. Esses animais foram separados ao acaso em cinco grupos, com quatro indivíduos. O úmero foi seccionado cirurgicamente na sua diáfise, de forma transversa, e o pino ósseo foi devidamente implantado no seio do osso. Orifícios foram realizados e por eles procedeu-se hemicerclagem do tipo pontos de Wolff com poliglactina 910. Os animais foram avaliados clinicamente, por meio de radiografias semanais, e histologicamente após os períodos de 15, 30, 60, 90 e 120 dias. A conservação do pino ósseo em glicerina a 98% foi avaliada por meio de exames microbiológicos. Em todos os animais, pode-se notar, clinicamente, excelente adaptação à cirurgia e normalidade do uso do membro já radiologicamente pode-se observar formação de calo ósseo e cicatrização da fratura. Histologicamente pode-se observar que ocorreu formação de calo ósseo 15 dias após a cirurgia e cicatrização com remodelação completa a partir dos 90 dias. Nesse exame, além de leve a moderada reação inflamatória no período inicial de avaliação, nenhum outro evento foi notado nos períodos subseqüentes. Concluiu-se que a técnica e os materiais utilizados se tornam uma opção altamente viável na osteossíntese umeral transversa de pombos domésticos.The objective of the present study was to evaluate the use of a homologous bone intramedullary pin, conserved in glycerin at 98% associated to hemicerclage with a thread of polyglactina 910 in the transverse humerus osteosynthesis of domestic pigeon (Columba livia. The distal part of the

  7. Membranas biológicas homólogas preservadas em solução alcalina seguida de liofilização, glicerina a 98% e por liofilização para implantação em eqüinos Homologous biological membranes persevered in alkaline solution and lyophilized, glycerin 98% and by lyophilization for equines implantation

    Directory of Open Access Journals (Sweden)

    Valcinir Aloisio Scolla Vulcani

    2008-08-01

    to evaluate physicist-chemistries alterations in equines diaphragmatic tendineous centers implants submitted to alkaline solution and lyophilization treatment. The samples had been treated in alkaline solution for 24, 48, 72, 120 and 144 hours and lyophilized. It was analyzed the homogeneity, flexibility and resistance to the suture. After that, they had been submitted to the differential scanner calorimetry and to the scanner electronic microscopy. Samples of 72 hours in alkaline treatment, conserved in glycerin 98% and only lyophilized were implanted in recto abdominis internal fascia of equines. They were removed one, nine and 18 weeks post-implantation to evaluate the existence of tacks. It was verified that the homogeneity and flexibility are directly proportional to the increase of time of treatment in alkaline solution while the resistance is inversely proportional to the time increase, being 72 hour treatment intermediate for these characteristics. The differential scanner calorimetry showed that the treatment do not denature the present collagen in samples. The electronic microscopy showed that the increase of treatment time provides expansion of less dense zones of the material. In relation to the formation of tacks, the samples only lyophilized had presented maximum degree in the proposal classification followed for the conserved in glycerin 98% samples with average degree and the treated in alkaline solution and lyophilized samples had been classified in minimum degree. It was concluded that the treatment for 72 hours would be more appropriate for implantation and that the tissue integration with abdominal wall was better in relation to the samples lyophilized only and to the conserved in glycerin ones.

  8. Treatment of Acute Fissure in Ano using Topical Glycerine Trinitrate ...

    African Journals Online (AJOL)

    RICHY

    longitudinal tear of the lower anal canal. It is one of the painful anal conditions resulting in a lot of ... constipation, doing so with a fresh tear more likely during next defecation. The aetiology varies from precipitous ... increases NO (nitric oxide) which is a very potent muscle relaxant. It acts on vascular smooth muscle there by.

  9. Aspectos clínicos e macroscópicos da palatoplastia imediata com implante de cartilagem da pina articular, conservada em glicerina a 98%, após indução experimental de fenda palatina em cães Clinic and macroscopic view of immediate palatoplasty with auricular pinna cartilage preserved in 98% glycerin in canine experimental palat cleft

    Directory of Open Access Journals (Sweden)

    Emerson Antônio Contesini

    2003-02-01

    Full Text Available Os defeitos de espessura completa do palato que resultam em comunicação oro-nasal raramente cicatrizam espontaneamente. Eles requerem reparo cirúrgico, porém, pode ser difícil obter cicatrização satisfatória devido às condições próprias das cavidades nasal e oral. Neste experimento, foram utilizados 14 cães, reunidos em dois grupos de igual número. Todos animais foram submetidos à indução de fenda palatina experimental. O grupo G1 foi o controle, cuja palatoplastia foi realizada a partir da confecção de "flap" muco-periósteo. No grupo G2, foi utilizada cartilagem da pina auricular conservada em glicerina a 98% entre o osso palatino e o muco-periósteo. Os animais foram avaliados macroscopicamente quanto ao processo cicatricial, por radiografias para a regeneração óssea e por rinoscopia para observar a regeneração da mucosa nasal. Foi observada a cicatrização da mucosa oral a partir do 10º dia, com deiscência de sutura em dois animais do grupo G1. A radiografia demonstrou evolução na cicatrização óssea, num processo mais acelerado no grupo G2 quando comparado ao grupo G1. A rinoscopia revelou, aos 60 dias, completa regeneração da mucosa nasal em ambos os grupos. Ao final do período de avaliação foi observada macroscopicamente, completa fusão óssea nos animais do grupo G2 e incompleta nos do grupo G1, o que demonstrou a interferência benéfica do implante no processo cicatricial do grupo G2.The incomplete defects of hard palate result in oro-nasal fistula seldom cure themselves in a spontaneous way, due to limited condition in oral and nasal cavity it may be difficult to obtain satisfactory cicatrization, requiring surgery to interfere in the healing process. Fourteen dogs arranged in two groups were submitted to experimental hard palate cleft. The G1 group was the control group, in which palatoplasty was achieved with mucous-periosteum flap. In the G2 group, a preserved at 98% glycerin auricular pinna

  10. Reparação traqueal em cães: transplante autógeno vs implante homógeno conservado em glicerina a 98% de cartilagem da pina Tracheal healing in dogs: autograft versus homograft implant preserved in 98% glycerin of pinna cartilage

    Directory of Open Access Journals (Sweden)

    Emerson Antonio Contesini

    2001-08-01

    them were submitted to an autograft (group I and six to homograft preserved in 98% glycerin (group II, to repair tracheal defects. One third of three cervical tracheal rings were removed and substituted for auto or homograft. These animals remained under observation and clinical evaluation in rest and moderate physical exercise during a 45 days period, without presenting any decurrent complications. At the end of the observation period, the trachea was submitted to gross and microscopic examination. Full epithelization of the grafted area was observed by macroscopic evaluation in both groups. Microscopic analyses showed granulation tissue in the transplanted area of group I, the lamina propria with moderate infiltration of neutrophile and few fibrosis with focus of epithelial hyperplasia. Animals of group II presented granulation around the area of the implantation and discrete invasion of macrophages and neomorph vases in the lamina propria, with moderate inflammation. The epithelium showed no alteration. These data suggest that the pinna cartilage homograft implant induce less aggressive response by the receiving streambed, even so this was not observed grossly.

  11. Ethanol-Glycerin Fixation with Thymol Conservation: A Potential Alternative to Formaldehyde and Phenol Embalming

    Science.gov (United States)

    Hammer, Niels; Loffler, Sabine; Feja, Christine; Sandrock, Mara; Schmidt, Wolfgang; Bechmann, Ingo; Steinke, Hanno

    2012-01-01

    Anatomical fixation and conservation are required to prevent specimens from undergoing autolysis and decomposition. While fixation is the primary arrest of the structures responsible for autolysis and decomposition, conservation preserves the state of fixation. Although commonly used, formaldehyde has been classified as carcinogenic to humans. For…

  12. Physical Evaluation of PVA/Chitosan Film Blends with Glycerine and Calcium Chloride

    Science.gov (United States)

    Nugraheni, A. D.; Purnawati, D.; Kusumaatmaja, A.

    2018-04-01

    PVA/chitosan film has been fabricated by using drop casting method. PVA/chitosan film is produced by dissolving 2% (w/v) PVA solution and 2% (w/v) chitosan solution. PVA/chitosan film is produced with weight ratio variation (w/w) 100/0, 75/25, 50/50 and 0/100. The film is fabricated using drop casting method in Petry dish with diameter 11 cm at room temperature and RH 50%–60% during seven days. The mechanical properties were characterized by using Universal Technical Machine (UTM) and UV-Vis to understand the physical properties of weight ratio (w/w) of PVA/Chitosan film by addition of plasticizer and calcium chloride. The film thickness tends to decrease with PVA content. The addition of chitosan will increase film thickness, and it will decrease swelling index, elongation (%), and transmittance of UV rays. The additions of plasticizer to PVA/Chitosan film will increase film thickness and elongation (%), and it will decrease swelling index, tensile strength and transmittance of UV rays. The crosslink of PVA/Chitosan film with calcium chloride will decrease film thickness, swelling index, elongation (%) and transmittance of UV rays, and increase tensile strength.

  13. The tertiary glycerin of acetylene and ethylen lines and their chemical transformations; Tretichnie glitserini atsetilenovogo ryadov i ih himicheskie prevrasheniya

    Energy Technology Data Exchange (ETDEWEB)

    Nikitin, V I

    1961-07-01

    In this monograph are summarised results of many years investigations, lead by author with group of colleagues of Institute of chemistry of Republic of Tajikistan in the field of synthesis of some new compounds classes of organic chemistry.

  14. 甘油冷冻保存阴道毛滴虫%PRESERVING TRICHOMONAS VAGINALIS BY FREEZING GLYCERINE

    Institute of Scientific and Technical Information of China (English)

    廖琳; 刘佩娜; 陈盛文

    1998-01-01

    本文采用10%甘油液氮保存阴道毛滴虫,连续分别观察1年、2年,37℃解冻后,阴道毛滴虫培养4天后均已生长繁殖.用瑞氏姬氏混合染色,形态特征明显,标本结构清晰,甘油具有价廉、无毒、无味的优点,可替代二甲基亚砜作为常用保护剂.

  15. Optimizing the performance of a reactor by reducing the retention time and addition of glycerin for anaerobically digesting manure

    NARCIS (Netherlands)

    Timmerman, M.; Schuman, E.; Eekert, M.; Riel, van J.W.

    2015-01-01

    Anaerobic digestion of manure is a widely accepted technology for energy production. However, only a minimal portion of the manure production in the EU is anaerobically digested and occurs predominantly in codigestion plants. There is substantial potential for biogas plants that primarily operate on

  16. Apparent metabolizable energy of by-products from the soybean oil industry for broilers: acidulated soapstock, glycerin, lecithin, and their mixture.

    Science.gov (United States)

    Borsatti, L; Vieira, S L; Stefanello, C; Kindlein, L; Oviedo-Rondón, E O; Angel, C R

    2018-01-01

    A study was conducted to determine the AMEn contents of fat by-products from the soybean oil industry for broiler chickens. A total of 390 slow-feathering Cobb × Cobb 500 male broilers were randomly distributed into 13 treatments having 6 replicates of 5 birds each. Birds were fed a common starter diet from placement to 21 d. Experimental corn-soy diets were composed of four fat sources, added at 3 increasing levels each, and were fed from 21 to 28 d. Fat sources utilized were acidulated soybean soapstock (ASS), glycerol (GLY), lecithin (LEC), and a mixture (MIX) containing 85% ASS, 10% GLY and 5% LEC. A 4 × 3 + 1 factorial arrangement was used with 4 by-products (ASS, GLY, LEC, or MIX), 3 inclusion levels and 1 basal diet. Each of the four fat by-product sources was included in the diets as follow: 2% of by-products (98% basal + 2% by-product), 4% (96% basal + 4% by-product), or 6% (94% basal + 6% by-product). Birds were submitted to 94, 96, 98, and 100% of ad libitum feed intake; therefore, the differences in AMEn consumption were only due to the added by-product. Total excreta were collected twice daily for 72 h to determine apparent metabolizable energy contents starting at 25 d. The AMEn intake was regressed against feed intake and the slope was used to estimate AMEn values for each fat source. Linear regression equations (P product were as follow: 7,153X - 451.9 for ASS; 3,916X - 68.2 for GLY; 7,051X - 448.3 for LEC, and 8,515X - 622.3 for MIX. Values of AMEn were 7,153, 3,916, 7,051, and 8,515 kcal/kg DM for ASS, GLY, LEC, and MIX, respectively. The present study generated AMEn for fat by-products data that can be used in poultry feed formulation. It also provides indications that, by adding the 3 by-products in the proportions present in the MIX, considerable economic advantage can be attained. © 2017 Poultry Science Association Inc.

  17. Validation of an analytical methodology for the determination of diethylene glycol and ethylene glycol as impurities in glycerin and propylene glycol

    International Nuclear Information System (INIS)

    Rosabal Cordovi, Ursula M; Fonseca Gola, Antonio; Cordovi Velazquez, Juan M; Morales Torres, Galina

    2014-01-01

    A methodology for the quantification of diethylene glycol (DEG) and the ethylene glycol (EG) impurities by gas Chromatography with flame ionization detector in glycerol and propylene glycol samples was developed and validated. It was selected dimethyl sulphoxide as internal standard. It was used hydrogen as carrier and auxiliary gas. The temperature program was 100°C holding one minute, then ramp to rate of 7.5°C/ min up to 200 °C. A Restek 624 column was used, with a flow in column of 4.20 ml/ min. Temperatures of the injector and detector were set at 220°C and 250 °C, respectively. The linearity was determined at 25-75 ?μg/ml as interval of concentrations for both impurities with correlation coefficients larger than 0.999. Detection Limits were settled down in 0.0350 μ?g/ml to the diethylene glycol, and 0.0572 μg/ml to ethylene glycol, while the quantitation limits were 0.1160 μ?g/ml to DEG and 0.1897 μg/ml to the EG. The recoveries were 99.98 % and 100.00 %, respectively; with RSD % 1.18 % to DEG, and 0.60 % to the EG. The obtained results demonstrated that the methodology was linear, accurate, robustness, sensitive and selective to be used in the determination of both impurities in the quality control of the glycerol and propylene glycol as raw materials

  18. Calcium-dependence of Donnan potentials in glycerinated rabbit psoas muscle in rigor, at and beyond filament overlap; a role for titin in the contractile process

    DEFF Research Database (Denmark)

    Coomber, S J; Bartels, E M; Elliott, G F

    2011-01-01

    contracts and breaks the microelectrode. Therefore the rigor state was studied. There is no reason to suppose a priori that a similar voltage switch does not occur during contraction, however. Calcium dependence is still apparent in muscles stretched beyond overlap (sarcomere length>3.8 μm) and is also seen...... in the gap filaments between the A- and I-band ends; further stretching abolishes the dependence. These experiments strongly suggest that calcium dependence is controlled initially by the titin component, and that this control is lost when titin filaments break. We suppose that that effect is mediated...

  19. Biodiesel waste products as soil amendments : evaluation of microbial, biological, and plant toxicity.

    Science.gov (United States)

    2011-10-22

    During biodiesel production, about 200 lbs of glycerol, commonly called glycerin, is produced for every 1 ton of biodiesel. As the : biodiesel industry grows, so does the need to dispose of this waste product. While potential uses for glycerin exist,...

  20. Membrana amniótica preservada em glicerina no reparo de feridas cutâneas de membros locomotores de eqüinos Equine amniotic membrane preserved in glycerin in reparing the equine limbs cütaneous wounds

    Directory of Open Access Journals (Sweden)

    Valdemir Alves de Oliveira

    1998-12-01

    Full Text Available Neste estudo experimental, avaliou-se o uso de membrana amniótica eqüina preservada em glicerina 98%, à temperatura ambiente, em feridas com cura por segunda intenção, nos membros locomotores de eqüinos. Foram provocadas cirurgicamente feridas de 9,6cm² na face lateral da articulação metacarpo-falangeana, face medial do terço proximal do metacarpo e face lateral do terço médio do metatarso de ambos os membros locomotores de cinco eqüinos adultos, perfazendo total de trinta feridas. Foram constituídos dois grupos experimentais com quinze feridas cada, sendo um destes grupos tratado com membrana amniótica, e o outro, grupo controle, tendo recebido apenas gaze umidecida em solução fisiológica. Os curativos foram trocados a cada 48horas, tendo sido a membrana amniótica e a gaze umidecida substituídas. Em todas as feridas foram mensurados a área, o grau de secreção, a formação de tecido de granulação exuberante e o tempo para a epitelização se completar. Realizou-se também exame bacteriológico e histopatológico em um grupo de feridas, tratadas e controle. Na membrana amniótica, fez-se determinação bioquímica de proteínas e identificação de fator de crescimento de fibroblasto. Em todas as feridas tratadas, observou-se: menor tempo para cicatrização, menor formação de tecido de granulação exuberante, menor incidência de bactérias patológicas e menor aumento na área total.In the present experimental study, the use of the equine amniotic membrane preserved in glvcerol 98%, at room temperature, in wounds with secound intention healing of equine limbs were evaluated. Surgical wounds of the size of 9.6cm² were made on the fetiock joint, medial aspect of the proximal third of the metacarpus and lateral aspect of the medium third of the metatarsus ofboth limbs offive adult horses, making a total of thirty wounds. Two experimental groups were made with fifteen wounds in each group, where one of these groups was treated with amniotic membrane, and the other, the control group, treated only with a damp gauze changed every 48 hours. In all the wounds the procedure was to evaluate the measurement of the área, degree of secretion, development of exuberant granulation tissue and the complete time of epitheliazation. Bacteriologic and histopatologic exams were made in a sample of the treated and contrai groups. The biochemical determination of proteins and the identification of fibroblastic growth factor were realized in the amnionic membrane. In all the treated wounds were observed shorter healing time, less formation of exuberant granulation tissue, smaller incidence of pathogenic bacterias and a smaller increase of the wound area.

  1. Chapter VII. The oxidation of ethylene line glycerin and of dihydro pyranol. A. General part(theoretical); Glava VII. Okislenie glitserinov etilenovogo ryada i digidropiranolov. A. Obshaya chast'(teoreticheskaya)

    Energy Technology Data Exchange (ETDEWEB)

    Nikitin, V I

    1961-07-01

    In this chapter of book author made conclusion that off-peak compounds obligatory will oxidize above all with breach on place of off-peak connection are incorrect against to off-peak compounds, in which unsaturated carbons connected with oxygen containing carbons.

  2. Conclusion; Zaklyuchenie

    Energy Technology Data Exchange (ETDEWEB)

    Nikitin, V I

    1961-07-01

    In this chapter of book are present conclusions about work done by author, in particular that he found comparatively simple and available ways of synthesis of glycerin of acetylene line and glycerin of ethylen line which before was unknown or almost unknown in the chemical literature.

  3. Introduction; Vvedenie

    Energy Technology Data Exchange (ETDEWEB)

    Nikitin, V I

    1961-07-01

    Introduction describes the present book. Its includes seven chapters. First four from them touch with glycerin of acetylene line-their receiving, studying their oxidation reactions, transformations under the influence of dehydrating methods. Last three chapters dedicated to glycerin of ethylen line-synthesis, their cyclization into substituted dihydropyran.

  4. Untitled

    Indian Academy of Sciences (India)

    investigations. So far the best work has been that of Bar (1933) who reported. 14 frequencies, previous workers having found only seven. Bar worked with a Salnple of glycerine (d = 1.26) of about 97% purity as supplied by a Swiss firm. The difficulty in getting a good picture with glycerine is the presence of fluorescence ...

  5. Drug: D00028 [KEGG MEDICUS

    Lifescience Database Archive (English)

    Full Text Available ame as: C00116 Therapeutic category: 2357 7139 7190 ATC code: A06AG04 A06AX01 ... Component of Glyceol (TN) [DR:D04285], Compound iodin...e glycerin [DR:D04412], Dental iodine glycerin [DR:D0488

  6. Drug: D01016 [KEGG MEDICUS

    Lifescience Database Archive (English)

    Full Text Available ne glycerin [DR:D04412], Dental iodine glycerin [DR:D04880], Elemenmic (TN), Iodine...ssified ... DG02017 ... Potassium Same as: C08219 Therapeutic category: 3221 ATC code: R05CA02 S01XA04 V03AB21 ... Component of Compound iodi

  7. Drug: D04875 [KEGG MEDICUS

    Lifescience Database Archive (English)

    Full Text Available D04875 Mixture ... Drug Zinc sulfate - iodine - sodium iodine - glycerin mixt; Neogl...ycerol (TN) Zinc sulfate [DR:D01081], Iodine [DR:D00108], Sodium iodine [DR:D04874], Glycerin [DR:D00028] ... Therapeutic category: 2790 ... PubChem: 17398205 ...

  8. Selected properties of biodegradable material produced from thermoplastic starch with by-products of food industry addition

    Directory of Open Access Journals (Sweden)

    Zdybel Ewa

    2017-06-01

    Full Text Available In this work extrusion process were used to create thermoplastic starch and to mix obtained starch with linen, quince and apple pomace at the same time. Obtained starch beads were formed in shapes. In experimental material was determined thermal conductivity, water absorption and the solubility in water. It is possible to get the biodegradable material produced from thermoplastic starch with an addition of fruit pomace. Adding pomace and glycerine to the biodegradable material made from starch change of susceptibility on water action. In the case of materials containing pomace, glycerine addition decreases the susceptibility on water action compared to the material manufactured with pomace addition but without glycerine. In the material containing pomace, glycerine addition caused the increase of the thermal insulation time compared to the material with pomace but no glycerine in it.

  9. Evaluation of glycerol derivative as emulsifier for oil based drilling fluids; Avaliacao de derivados de glicerina como emulsificante para fluidos de perfuracao de base oleo

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Susan A. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Escola de Quimica; Cavalcanti, Milena Y.; Rodrigues Junior, Jorge; Lachter, Elizabeth R.; Nascimento, Regina Sandra V. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Inst. de Quimica

    2008-07-01

    In view of the growing search for new applications for the surplus glycerine of biodiesel production, the use of a glycerine derivative as emulsifier in oil based muds is proposed in this work. Glycerine monooleate was synthesized through esterification reaction, and characterized by NMR{sup 13}C. Its applicability as emulsifier was verified through electric stability tests performed on inverted phase drilling fluids. The obtained results were compared with two formulations containing different emulsifiers (sorbitol monooleate and trimethylolpropane monooleate). It was also evaluated the rheological properties of the formulated fluids through standard tests. It was verified that the fluid that contained the glycerine derivative showed considerably better electric stability results than the other systems. It also presented rheological properties similar to the ones shown by the system that contained the commercial emulsifier (sorbitol monooleate). Thus, it was found that glycerine monooleate is a potential substitute to the currently emulsifiers (author)

  10. Parent run science clubs: A case study at Nooitgedacht 88 primary school

    CSIR Research Space (South Africa)

    Butgereit, L

    2006-12-01

    Full Text Available ” λ Coke and Mentos 28 “Eye Popper” and “Attention Getter” λ Coke and Mentos 29 “Eye Popper” and “Attention Getter” λ Coke and Mentos 30 “Eye Popper” and “Attention Getter” λ Coke and Mentos λ Potassium Permanganate and Glycerine 31 “Eye... Popper” and “Attention Getter” λ Coke and Mentos λ Potassium Permanganate and Glycerine 32 “Eye Popper” and “Attention Getter” λ Coke and Mentos λ Potassium Permanganate and Glycerine 33 “Eye Popper” and “Attention Getter” λ Coke and Mentos...

  11. Utilização de argilas para purificação de biodiesel

    Directory of Open Access Journals (Sweden)

    Andréia Juliana Almeida de Paula

    2011-01-01

    Full Text Available This work describes the results of the purification of methyl biodiesel, obtained by oxidized soybean oil, using different methods. After the ester separation from the glycerin by decanting, the ester was purified each time with distillation, washing with water and adsorption with bauxite, bentonite and attapulgite. The removal of total contamination, unsaponifiable material, concentrations of free glycerin and soap were analyzed in the purified ester phase. The best result of purification was observed with the use of bentonite and bauxite, in the removal of soap and free glycerin respectively.

  12. Production of lactic acid from C6-polyols by alkaline hydrothermal reactions

    International Nuclear Information System (INIS)

    Zhou Huazhen; Jin Fangming; Wu Bing; Cao Jianglin; Duan Xiaokun; Kishita, Atsushi

    2010-01-01

    Production of lactic acid from C6-polyols (Mannitol) under alkaline hydrothermal conditions was investigated. Experiments were performed to examine the difference in the production of lactic acid between C6-polyols and C3-polyols (glycerine), as well as C6-aldoses (glucose). Results showed that the yield of lactic acid from C6-polyols was lower than that from both glycerine and glucose. It indicated that long chain polyols might follow a different reaction pathway from that of glycerine. Further investigation is needed to clarify the reaction mechanism and improve the relatively low lactic acid acid yield from C6-polyols.

  13. Nematoda: Dorylaimida

    African Journals Online (AJOL)

    1992-04-02

    sedimenta- tion method (Loubser 1985), killed by gentle heat, fixed in. FAA, processed into glycerine by Thome's slow method and mounted on permanent slides. Measurements and draw- ings were made with the aid of a Zeiss ...

  14. diffusion of metronidazole released through cellulose membrane

    African Journals Online (AJOL)

    prof kokwaro

    was determined using dialyzing cellulose membrane in a dissolution tester. Glycerin, a permeation ... An attempt has been made in the present ... Materials. Metronidazole USP was donated by Cosmos. Pharmaceutical Ltd., Nairobi, Kenya.

  15. South African Medical Journal Suid,Afrikaanse Tydskrif vir ...

    African Journals Online (AJOL)

    printed brochure entitled 'Constipation-Its Types and. Therapy'. ... ment are attributed to constipation. The child is tbus, .... glycerine and water, which must gradually be reduced in strength ... ently innocuous and chemically inert oil prevents.

  16. Presidential Green Chemistry Challenge: 2006 Academic Award

    Science.gov (United States)

    Presidential Green Chemistry Challenge 2006 award winner, Professor Galen J. Suppes, developed a process to convert waste glycerin from biodiesel production into propylene glycol to replace ethylene glycol in antifreeze.

  17. Supercritical water reformation of crude glycerol solution for hydrogen production.

    Science.gov (United States)

    2009-12-01

    Glycerol, also known as glycerin, is a less desirable byproduct formed in the production of biodiesel via the transesterification otriglycerides and presents a nontrivial issue in terms of developing other beneficial end uses. With an inflated glycer...

  18. Modification of γ-induced mutagenesis in Ames test-strains

    International Nuclear Information System (INIS)

    Basha, S.G.; Krasavin, E.A.; Kozubek, S.; Amirtaev, K.G.

    1990-01-01

    Glycerine and cysteamine protective effect on mutagenesis was studied in 3 strains of Salmonella typhimurium under γ-radiation. Glycerine modifying effect was shown to be not similar for various test-strains and depended on DNA injury nature. DNA complex injuries were shown to play significant role in mutagenesis of TA100 and TA102 strains. Absence of cysteamine modifying effect on γ-induced mutagenesis testified to cysteamine effect on enzyme balance. 20 refs.; 2 figs.; 1 tab

  19. Characterization of a dielectric microdroplet thermal interface material with dispersed nanoparticles

    International Nuclear Information System (INIS)

    Hamdan, A.; Sahli, F.; Richards, R.; Richards, C.

    2012-01-01

    This work presents the fabrication and characterization of a dielectric microdroplet thermal interface material (TIM). Glycerin droplets, 1 μL, were tested as TIMs in this study. Copper nanoparticles having a diameter of 25 nm were dispersed in glycerin at different volume fractions to enhance its thermal conductivity. An increase of 57.5% in the thermal conductivity of glycerin was measured at a volume fraction of 15%. A minimum thermal interface resistance of 30.37 mm 2 K/W was measured for the glycerin microdroplets at a deformed droplet height of 10.2 μm. Good agreement between experimental measurements and the predictions of a model based on Maxwell’s equation of rules of mixtures was obtained. The effect of nanoparticles' size on the effective thermal conductivity of glycerin was studied. Nanoparticles with diameters of 60–80 and 300 nm were dispersed in glycerin at a volume fraction of 5%, and their results were compared to those of the 25 nm particles.

  20. Biodiesel production from Jatropha curcas: Integrated process optimization

    International Nuclear Information System (INIS)

    Huerga, Ignacio R.; Zanuttini, María Soledad; Gross, Martín S.; Querini, Carlos A.

    2014-01-01

    Highlights: • The oil obtained from Jatropha curcas fruits has high variability in its properties. • A process for biodiesel production has been developed for small scale projects. • Oil neutralization with the glycerine phase has important advantages. • The glycerine phase and the meal are adequate to produce biogas. - Abstract: Energy obtained from renewable sources has increased its participation in the energy matrix worldwide, and it is expected to maintain this tendency. Both in large and small scales, there have been numerous developments and research with the aim of generating fuels and energy using different raw materials such as alternative crops, algae and lignocellulosic residues. In this work, Jatropha curcas plantation from the North West of Argentina was studied, with the objective of developing integrated processes for low and medium sizes farms. In these cases, glycerine purification and meal detoxification processes represent a very high cost, and usually are not included in the project. Consequently, alternative uses for these products are proposed. This study includes the evaluation of the Jatropha curcas crop during two years, evaluating the yields and oil properties. The solids left after the oil extraction were evaluated as solid fuels, the glycerine and the meal were used to generate biogas, and the oil was used to produce biodiesel. The oil pretreatment was carried out with the glycerine obtained in the biodiesel production process, thus neutralizing the free fatty acid, and decreasing the phosphorous and water content

  1. Flow characteristics of Newtonian and non-Newtonian fluids in a vessel stirred by a 60° pitched blade impeller

    Directory of Open Access Journals (Sweden)

    Jamshid M. Nouri

    2008-03-01

    Full Text Available Mean and rms velocity characteristics of two Newtonian flows at Reynolds numbers of 12,800 (glycerin solution and 48,000 (water and of a non-Newtonian flow (0.2% CMC solution, at a power number similar to the Newtonian glycerin flow in a mixing vessel stirred by a 60° pitched blade impeller have been measured by laser Doppler velocimetry (LDV. The velocity measurements, resolved over 360° and 1.08° of impeller rotation, showed that the mean flow of the two power number matched glycerin and CMC flows were similar to within 3% of the impeller tip velocity and the turbulence intensities generally lower in the CMC flow by up to 5% of the tip velocity. The calculated mean flow quantities showed similar discharge coefficient and pumping efficiency in all three flows and similar strain rate between the two power number matched glycerin and CMC flows; the strain rate of the higher Reynolds number Newtonian flow was found to be slightly higher. The energy balance around the impeller indicated that the CMC flow dissipated up to 9% more of the total input power and converted 7% less into the turbulence compared to the glycerin flow with the same power input which could lead to less effective mixing processes where the micro-mixing is important.

  2. FORMULASI SEDIAAN MOUTHWASH PENCEGAH PLAK GIGI EKSTRAK BIJI KAKAO (Theobroma cacao L DAN UJI EFEKTIVITAS PADA BAKTERI Streptococcus mutans

    Directory of Open Access Journals (Sweden)

    Apriyanti Anastasia

    2017-03-01

    Full Text Available Research on the formulation of preparations mouthwash prevention of dental plaque extract of cocoa beans also has been tested in Streptococcus mutans bacteria by variations in the concentration of glycerin as a humectant in preparation which aims to determine the effect of different concentrations of glycerin as a humectant to the physical properties, chemical properties and inhibition zone Streptococcus mutans bacteria in mouthwash formula and to know the mouthwash formula that has the physical quality and the highest antibacterial activity. The method used includes the step of extraction of cocoa beans, preparation of a mouthwash with 4 formula using variations of glycerin F1 (0%, F2 (15%, F3 (20% and F4 (25% followed by an evaluation formula that includes organoleptic tests, pH test and the test of inhibition diameter. Tests performed on days 0, 7, 14 and 21. The results showed the concentration of glycerin as a humectant in a mouthwash formula cocoa seed extract has an effect on the diameter of inhibition zone, but did not have a significant effect on the physical and chemical properties of cocoa seed extracts mouthwash, The concentration of glycerin which meets the physical quality and the most excellent antibacterial activity that is 15% contained in the formula 2.

  3. By-products from the biodiesel chain as a substrate to citric acid production by solid-state fermentation.

    Science.gov (United States)

    Schneider, Manuella; Zimmer, Gabriela F; Cremonese, Ezequiel B; de C de S Schneider, Rosana; Corbellini, Valeriano A

    2014-07-01

    In this study, we propose the use of tung cake for the production of organic acids, with an emphasis on citric acid by solid-state fermentation. We evaluated the conditions of production and the by-products from the biodiesel chain as raw materials involved in this bioprocess. First, we standardized the conditions of solid-state fermentation in tung cake with and without residual fat and with different concentrations of glycerine using the fungus Aspergillus niger The solid-state fermentation process was monitored for 7 days considering the biomass growth and pH level. Citric acid production was determined by high-performance liquid chromatography. Fungal development was better in the crude tung cake, consisting of 20% glycerine. The highest citric acid yield was 350 g kg(-1) of biomass. Therefore, the solid-state fermentation of the tung cake with glycerine led to citric acid production using the Aspergillus niger fungus. © The Author(s) 2014.

  4. Mixing compatibilities of Aspergillus and American cockroach allergens with other high-protease fungal and insect extracts.

    Science.gov (United States)

    Grier, Thomas J; Hall, Dawn M; Duncan, Elizabeth A; Coyne, Terrance C

    2015-03-01

    Recent studies have shown that Alternaria and German cockroach allergens can be degraded by endogenous proteases from other insect and fungal extracts when combined for immunotherapy, but data supporting the compatibilities of other high-protease products in comparable mixtures have not been reported. To assess the stabilities and compatibilities of Aspergillus fumigatus and American cockroach allergens after mixing with protease-rich extracts from other insects or fungi at concentrations similar to those recommended for subcutaneous immunotherapy. Mixtures containing A fumigatus, American cockroach, and other fungal or insect extracts were evaluated by quantitative (enzyme-linked immunosorbent assays) and qualitative (immunoblotting) methods. Test mixtures and control samples at 10% to 50% glycerin concentrations were analyzed after storage for up to 12 months at 2°C to 8°C. Moderate to high recoveries of Aspergillus extract activities were retained in control samples and extract mixtures under all conditions examined. American cockroach extract controls were partly degraded at 10% to 25% glycerin, and cockroach allergen compatibilities were decreased significantly in mixtures with several fungal extracts at 25% glycerin. Mixing with other insects did not compromise the stability of American cockroach allergens at 25% to 50% glycerin. Aspergillus extracts exhibited favorable stabilities after mixing with other high-protease products. American cockroach extract potencies were unstable in less than 50% glycerin, even in the absence of other protease-containing allergens, and were destabilized in mixtures with several fungal extracts. Addition of fungal and insect extracts to separate treatment vials or preparation of fungal-insect mixtures at elevated glycerin concentrations might be necessary to produce compatible patient formulations for allergen immunotherapy injections. Copyright © 2015 American College of Allergy, Asthma & Immunology. Published by Elsevier

  5. Morphological properties of fresh and preserved paca peritoneum (Cuniculus paca, L. 1766

    Directory of Open Access Journals (Sweden)

    Angela Daniele de Camargo

    2012-11-01

    Full Text Available The objective of this study was to describe the morphological characteristics of peritoneum samples from four adult pacas, which were fresh and preserved in 98% glycerin for 30, 60 and 90 days. Samples were analyzed using light and scanning electron microscopy. A clear arrangement between the dense, modeled connective tissue and the dense, unmodeled connective tissue, and an insignificant change in the membrane tissue integrity, were observed in the material preserved in the glycerin. The results suggest that paca peritoneum can be used as a biological material.

  6. Chemico-therapeutic approach to prevention of dental caries. [using stannous fluoride gel

    Science.gov (United States)

    Shannon, I. L.

    1975-01-01

    The program of chemical preventive dentistry is based primarily upon the development of a procedure for stabilizing stannous fluoride in solution by forcing it into glycerin. New topical fluoride treatment concentrates, fluoride containing gels and prophylaxis pastes, as well as a completely stable stannous fluoride dentifrice are made possible by the development of a rather complicated heat application method to force stannous fluoride into solution in glycerin. That the stannous fluoride is clinically effective in such a preparation is demonstrated briefly on orthodontic patients.

  7. Video of Miscible Fluid Experiment Conducted on NASA Low Gravity Airplane

    Science.gov (United States)

    2003-01-01

    This is a video of dyed water being injected into glycerin in a 2.2 centimeter (cm) diameter test tube. The experiment was conducted on the KC-135 aircraft, a NASA plane that creates microgravity and 2g conditions as it maneuvers through multiple parabolas. The water is less dense and so it rises to the top of the glycerin. The goal of the experiment was to determine if a blob of a miscible fluid would spontaneously become spherical in a microgravity environment.

  8. Food preferences of wild house-mice (Mus musclus L).

    Science.gov (United States)

    Rowe, F P; Bradfield, A; Redfern, R

    1974-12-01

    The relative acceptance of various plain foods by wild house-mice (Mus musculus L.) was compared in laboratory choice tests. The palatability of glycerine and six oils, each included at 5% in pinhead oatmeal, was compared in a similar manner.The most favoured food was found to be whole canary seed (Phalaris canariensis). Pinhead oatmeal and wheat were also comparatively well accepted. Glycerine, corn oil, arachis oil and mineral oil were more palatable than either olive, linseed or cod-liver oils.The results of the choice tests are considered in relation to the use of poison baits for the control of free-living mice.

  9. Food preferences of wild house-mice (Mus musculus L.)*

    Science.gov (United States)

    Rowe, F. P.; Bradfield, A.; Redfern, R.

    1974-01-01

    The relative acceptance of various plain foods by wild house-mice (Mus musculus L.) was compared in laboratory choice tests. The palatability of glycerine and six oils, each included at 5% in pinhead oatmeal, was compared in a similar manner. The most favoured food was found to be whole canary seed (Phalaris canariensis). Pinhead oatmeal and wheat were also comparatively well accepted. Glycerine, corn oil, arachis oil and mineral oil were more palatable than either olive, linseed or cod-liver oils. The results of the choice tests are considered in relation to the use of poison baits for the control of free-living mice. PMID:4531454

  10. Effects of topical 2% cyclosporine A on the corneas of dogs subjected to lamellar keratoplasty with a graft of equine pericardium preserved in glycerin: clinical and morphological evaluation Efeitos da aplicação tópica da ciclosporina A a 2% sobre a córnea de cães submetidos à ceratoplastia lamelar com implante de pericárdio de eqüino preservado em glicerina: avaliação clínica e morfológica

    Directory of Open Access Journals (Sweden)

    Roseli Borges Teixeira

    2004-02-01

    Full Text Available The effects of topical 2% cyclosporine A on the cornea of dogs subjected to experimental lamellar keratoplasty with an equine pericardial graft were evaluated. Ten dogs were grouped to be evaluated 3, 7, 15, 30 and 60 days after surgery. Animals received bilateral grafts followed by the application of a 2% cyclosporine A ointment on the left eye (treated eye and the ointment base on the right eye (control eye twice a day. The ophthalmic evaluation showed profound bilateral blepharospasm, photophobia and a mucous secretion until the 7th day after surgery; corneal vascularization starting in the limbus was observed as early as the 3rd day in both eyes; opacification and vascularization were more intense in the treated cornea on days 15 and 30 after surgery. Vascularization was still evident on the 60th day, and looked similar in treated eyes and control eyes. The histologic evaluation showed a complete bilateral reepithelization and corneal vascularization three days after the surgery; intense vascularization in both eyes on days 15 and 30, that was much more pronounced in the treated cornea; and a bilateral predominance of polymorphonuclear cells until day 15, and mononuclear cells on day 30. Intact epithelium and stroma with new vessels, as well as graft absorption, in both eyes, were seen on the 60th day. The lamellar keratoplasty with equine pericardial graft was an effective model to study the inflammatory kinetics and corneal vascularization phenomenon. In this study, cyclosporine A did not inhibit corneal vascularization and it did not interfere in the corneal cicatricial process.Foram avaliados os efeitos da ciclosporina A a 2% sobre a córnea de cães submetidos à ceratoplastia lamelar experimental com implante de pericárdio de equino. Dez cães foram divididos em grupos para estudo aos três, sete, 15, 30 e 60 dias de pós-operatório, recebendo implantes bilaterais e em seguida aplicação da pomada com ciclosporina A a 2% no olho esquerdo (olho tratadoe somente a base da mesma pomada no olho direito (olho controle, duas vezes ao dia. À avaliação oftalmológica observou-se, bilateralmente, blefarospasmo, fotofobia e secreção mucosa evidentes até 7 dias de pós-operatório; início de vascularização a partir do limbo aos três dias, bilateralmente; opacidade e vascularização mais intensos em córnea esquerda aos 15 e 30 dias; vascularização ainda evidente, bilateralmente, com aspecto semelhante aos 60 dias. À avaliação histopatológica observou-se, bilateralmente, completa reepitelização e vascularização aos três dias de pós-operatório; vascularização intensa aos 15 e 30 dias, bilateralmente, porém acentuada na córnea esquerda; predomínio de polimorfonucleares até os 15 dias e mononucleares aos 30 dias, bilateralmente; epitélio e estroma íntegros com vasos ainda evidentes e implante incorporado ao estroma, bilateralmente, aos 60 dias. A utilização do implante de pericárdio de equino em ceratoplastias lamelares em cães constitui uma técnica eficaz, aplicável ao estudo da cinética inflamatória e fenômeno de vascularização. A ciclosporina A a 2% não inibiu ou diminuiu a formação vascular na córnea e também não interferiu no processo cicatricial neste estudo.

  11. Comparação entre a técnica de substituição do ligamento redondo por implante de fascia lata bubalina preservada em glicerina e o uso de pino transarticular na redução e na estabilização da luxação coxofemoral experimentalmente induzida em cães Comparation between the technique of substitution of the round ligamentum by glycerin-preserved bubaline fascia lata implant and the use of transarticular pin in the redution and stabilization of experimentally induzed coxofemoral luxation in dogs

    Directory of Open Access Journals (Sweden)

    D.B. Sia

    2009-08-01

    Full Text Available Compararam-se duas técnicas cirúrgicas de redução e estabilização da articulação coxofemoral experimentalmente luxada em cães. Dois grupos de animais, submetidos às respectivas técnicas após a indução cirúrgica da luxação, foram acompanhados clínica e radiograficamente por um período de 60 dias, findos os quais, realizaram-se avaliações macroscópica e histológica e teste de tensiometria das articulações. Cada grupo foi constituído por oito animais, clinicamente sadios, com pesos entre 5 e 20kg. Os animais submetidos ao implante de fáscia apresentaram, ao exame físico, evolução da deambulação significativamente precoce em relação aos do grupo submetido ao implante de pino de Steinmann, além de menor grau de atrofia muscular. Os testes de tensiometria, as avaliações macroscópicas e radiográficas e os exames histológicos não diferiram entre os grupos, evidenciando também que ambas as técnicas não geraram alterações deletérias à articulação operada. Conclui-se que a técnica de estabilização da articulação coxofemoral com implante de fascia lata foi clinicamente eficaz e vantajosa quando comparada à técnica do pino transarticular.It was compared both surgical techniques of reduction and stabilization of experimentally luxated coxofemoral join in dog. Two groups were submitted to the techniques after surgical induction of the luxation. All animals were clinically and radiografically observed during 60 days. After that, a macroscopic study, an histological exam, and a tensiometry test in the articulations were performed. Each group had eight healthy animals, weighting from 5 to 20kg. The most important advantage was related to the deambulation, which the animals submited to the facia lata implant showed a faster evolution after the surgery at the physical exam, and muscular atrophy in a smaller degree. The tensiometry tests, the radiographic and the histological exams did not present important differences between both groups, but they were useful to show that the two techniques did not cause alterations in the studied articulation. It can be concluded that the stabilization of the coxofemoral articulation using bubaline fascia lata implant was clinically efficient and more advantageous compared to the transarticular pin technique.

  12. 21 CFR 344.12 - Ear drying aid active ingredient.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Ear drying aid active ingredient. 344.12 Section 344.12 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... alcohol 95 percent in an anhydrous glycerin 5 percent base. [65 FR 48905, Aug. 10, 2000] ...

  13. Microwave-assisted liquefaction of wood with polyhydric alcohols and its application in preparation of polyurethane (PU) foams

    Science.gov (United States)

    Hui Pan; Zhifeng Zheng; Chung Y. Hse

    2011-01-01

    Microwave radiation was used as the heating source in southern pine wood liquefaction with PEG/glycerin binary solvent. It was found that microwave heating was more efficient than conventional oil bath heating for wood liquefaction. The wood residue content of the H2SO4 catalyzed liquefied wood dropped to zero within 5 min with microwave heating. The resulting...

  14. from Capri vi, Namibia (Nematoda: Onchulinae)

    African Journals Online (AJOL)

    1992-10-01

    Oct 1, 1992 ... 1940). The species herein described does not fit into any of the existing genera, and we accordingly propose a new genus for its reception. Material and Methods. Descriptions, measurements and drawings were made from specimens killed and fixed in hot FAA (70°C) and mounted in anhydrous glycerine.

  15. Freshwater nematodes from South Africa. 8. New and known ...

    African Journals Online (AJOL)

    fIxed in FAA and processed into glycerine by Thome's slow method. Measurements and drawings were made from glyce- rine-mounted specimens by means of a camera lucida. Family Paractinolaimidae Thome, 1967. Genus Afractinolaimus Andrassy, 1970. In 1970 Andrassy described Ajradinolaimus noblei from South.

  16. i03

    African Journals Online (AJOL)

    and fixed in hot FAA and mounted in anhydrous glycerine. Measurements were made along the median line. The oesophagus length was taken from the anterior end, and the positions of oesophageal glands as percentages of this length. All mounL' are deposited in the nematode collection of the Rand Afrikaans University.

  17. AVALIAÇÃO DO POTENCIAL USO DE BIOGLICERINA COMO BASE PARA FORMULAÇÃO DE FLUIDOS DE PERFURAÇÃO AQUOSOS PARA POÇOS DE PETRÓLEO E GÁS

    Directory of Open Access Journals (Sweden)

    Cleysson C. Corrêa

    Full Text Available The growing global concern about the environment associated with academic and government efforts are enabling a number of alternatives for sustainable development. Within this perspective one can include the search for value-added products using waste from renewable energy sources, such as those from the production of biodiesel. The rapid development of biodiesel production in Brazil directly affected the supply of glycerin and therefore the sector is seeking a market that can absorb this waste. Thus, with the increasing search for environmentally friendly products, formulation of a drilling fluid using a co-product of biodiesel production to replace the n-paraffin is of great importance to the oil industry for meeting the requirement of environmental regulation and, in addition, considerably reducing the cost of raw materials. In this context, the aim of this study was to characterize different glycerins to evaluate their potential as basis for drilling fluids for oil wells and gas. The glycerins were stable under the conditions evaluated without phase separation and precipitation of solids, exhibited good rheological profile and low value of interface tension. The results indicate a strong possibility of use of these glycerins as basis for drilling fluids and applicability by the oil industry.

  18. Carboxyhaemoglobin levels, health and lifestyle perceptions in ...

    African Journals Online (AJOL)

    Background. Chronic obstructive pulmonary disease and lung cancer are diseases associated with smoking tobacco cigarettes. Smokers find cessation difficult. Objectives. To determine whether smoking the Twisp electronic cigarette (e-cigarette), containing nicotine in a vegetable-based glycerine substance, would reduce ...

  19. Surface tension and wetting properties of rapeseed oil to biofuel conversion by-products

    Science.gov (United States)

    Muszyński, Siemowit; Sujak, Agnieszka; Stępniewski, Andrzej; Kornarzyński, Krzysztof; Ejtel, Marta; Kowal, Natalia; Tomczyk-Warunek, Agnieszka; Szcześniak, Emil; Tomczyńska-Mleko, Marta; Mleko, Stanisław

    2018-04-01

    This work presents a study on the surface tension, density and wetting behaviour of distilled glycerol, technical grade glycerol and the matter organic non-glycerin fraction. The research was conducted to expand the knowledge about the physical properties of wastes from the rapeseed oil biofuel production. The results show that the densities of technical grade glycerol (1.300 g cm-3) and distilled glycerol (1.267 g cm-3) did not differ and were significantly lower than the density of the matter organic non-glycerin fraction (1.579 g cm-3). Furthermore, the surface tension of distilled glycerol (49.6 mN m-1) was significantly higher than the matter organic non-glycerin fraction (32.7 mN m-1) and technical grade glycerol (29.5 mN m-1). As a result, both technical grade glycerol and the matter organic non-glycerin fraction had lower contact angles than distilled glycerol. The examined physical properties of distilled glycerol were found to be very close to that of the commercially available pure glycerol. The results suggest that technical grade glycerol may have potential application in the production of glycerol/fuel blends or biosurfactants. The presented results indicate that surface tension measurements are more useful when examining the quality of biofuel wastes than is density determination, as they allow for a more accurate analysis of the effects of impurities on the physical properties of the biofuel by-products.

  20. Methanol-induced chain termination in poly(3-hydroxybutyrate) biopolymers: molecular weight control

    Science.gov (United States)

    A systematic study was performed to demonstrate the impact of methanol (MeOH) on poly(3-hydroxybutyrate) (PHB) synthesis and molecular weight (MW) control. Glycerine (init. conc. = 1.0%; w/v), was used as the primary carbon source in batch-culture fermentations with varying concentrations (0 to 0.85...

  1. 77 FR 699 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

    Science.gov (United States)

    2012-01-05

    ... require new agricultural sector modeling and involved relatively straightforward analyses that largely... fermentation [cir] Biochemical fermentation with catalytic upgrading [cir] Any other process that uses biogas... RFS2 of picking a surrogate use for modeling purposes in the mid-range of likely glycerin uses, and the...

  2. James Moir (1874–1929) Pioneering Chemical Analyst in South ...

    African Journals Online (AJOL)

    NICO

    This was a starch KI paper moistened with a 50 % glycerine solution. A brown ... The NO produced in this side reaction is oxidized to NO2 and by cancelling one ..... tion either with FeCl3 or CrO3, evidently due to oxidation. Also, when treated ...

  3. Alternative binder for copper concentrate briquetting

    Directory of Open Access Journals (Sweden)

    J. Łabaj

    2015-10-01

    Full Text Available In the paper, results of investigations on the use of new, alternative binder, based on technical grade glycerine and higher alcohols, for copper matte briquetting are presented. The use of alternative binder yields briquettes that show better drop and compressive strength properties compared with briquettes produced using traditional, sulphite lye binding material.

  4. Life cycle assessment of castor-based biorefinery: a well to wheel LCA

    DEFF Research Database (Denmark)

    Khoshnevisan, Benyamin; Rafiee, Shahin; Tabatabaei, Meisam

    2017-01-01

    of their ability in converting biomass into a spectrum of marketable products and bioenergies. This study was aimed at developing different novel castor-based biorefinery scenarios for generating biodiesel and other co-products, i.e., ethanol and biogas. In these scenarios, glycerin, heat, and electricity were...

  5. Structural, spectroscopic and biological investigation of copper oxides nanoparticles with various capping agents

    Energy Technology Data Exchange (ETDEWEB)

    Nowak, A., E-mail: ana.maria.nowak@gmail.com [A. Chelkowski Institute of Physics, University of Silesia, Katowice (Poland); Szade, J.; Talik, E.; Ratuszna, A. [A. Chelkowski Institute of Physics, University of Silesia, Katowice (Poland); Ostafin, M. [Agricultural University of Cracow, Department of Microbiology, Krakow (Poland); Peszke, J. [A. Chelkowski Institute of Physics, University of Silesia, Katowice (Poland)

    2014-06-01

    Powder composed of copper oxides nanoparticles with various capping agents has been synthesized and characterized with the use of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Polyvinyl alcohol (PVA), glycol propylene, glycerin and glycerin plus ammonia were used as capping agents. The scanning electron microscopy (SEM) studies showed that nanoparticles form agglomerates with the size from 80 to 120 nm while particles size determined from the XRD experiment was in the range from 7 to 21 nm. XPS and XRD experiments revealed that depending on capping and reducing agents used in the synthesis nanoparticles are composed of Cu{sub 2}O, CuO or a mixture of them. The biological activity test performed for a selected sample where the capping agent was glycerin plus ammonia has shown promising killing/inhibiting behavior, very effective especially for Gram negatives bacteria. - Highlights: • We obtained copper oxide nanoparticles in a powder form. • Several capping agents were tested. • Structural and chemical tests showed that the main component were Cu{sub 2}O and CuO. • The size of nanoparticles was in the range 7–21 nm. • Nanoparticles with glycerin and ammonia capping agent showed good antibacterial properties.

  6. Fractionation of heavy metals in liquefied chromated copper arsenate (CCA)-treated wood sludge using a modified BCR-sequential extraction procedure

    Science.gov (United States)

    Hui Pan; Chung-Yun Hse; Robert Gambrell; Todd F. Shupe

    2009-01-01

    Chromated copper arsenate (CCA)-treated wood was liquefied with polyethylene glycol/glycerin and sulfuric acid. After liquefaction, most CCA metals (98% As, 92% Cr, and 83% Cu) were removed from liquefied CCA-treated wood by precipitation with calcium hydroxide. The original CCA-treated wood and liquefied CCA-treated wood sludge were fractionated by a modified...

  7. Characterization of viscous biofuel sprays using digital imaging in the near field region

    NARCIS (Netherlands)

    Sallevelt, J.L.H.P.; Pozarlik, Artur Krzysztof; Brem, Gerrit

    2015-01-01

    The atomization of biodiesel, vegetable oil and glycerin has been studied in an atmospheric spray rig by using digital imaging (PDIA). Images of the spray were captured in the near field, just 18 mm downstream of the atomizer, and processed to automatically determine the size of both ligaments and

  8. African Journal of Biotechnology - Vol 14, No 45 (2015)

    African Journals Online (AJOL)

    Selection of okra parents based on performance and genetic divergence · EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT DOWNLOAD ... Glycerine associated molecules with herbicide for controlling Adenocalymma peregrinum in cultivated pastures · EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT DOWNLOAD ...

  9. Biodiesel Waste Products as Soil Amendments - Field Study and Runoff Impacts

    Science.gov (United States)

    2012-08-01

    For every ten kilograms of biodiesel that is produced, approximately 1 kilogram of glycerol is created as a byproduct. Glycerol, also known as glycerin or glycyl alcohol is a chemical used in all manner of common goods including but not limited to ma...

  10. Tools to Ensure Safe Medicines: New Monograph Tests in USP-NF

    Directory of Open Access Journals (Sweden)

    Catherine Sheehan

    2010-06-01

    Full Text Available This paper describes USP-NF compendial updates to six ‘high-priority” excipient monographs: Glycerin, Propylene Glycol, Sorbitol Solution, Sorbitol Sorbitan Solution, Noncrystallizing Sorbitol Solution and Maltitol Solution. The USP-NF revisions arose from the Food and Drug Administration’s (FDA’s requests to include, as part of each monograph’s Identification test, a limit test to detect the presence of Diethylene Glycol (DEG, a toxic adulterant. These revisions align with the 2007 FDA Guidance for Industry: Testing of Glycerin for Diethylene Glycol (1, that drug product manufacturers perform a specific identity test for DEG on all containers of all lots of glycerin before glycerin is used in the manufacture and preparation of drug products. This paper describes several risk factors due to a complex global excipient supply chain, nonspecific specifications, inadequate supply chain qualification, and poor understanding of regulations. Strengthening and conformance to compendial specifications is one of the tools necessary to mitigate risk and help prevent the next DEG adulteration that is part of USP’s efforts to ensure safe medicines.

  11. Recovery of Glycerol from Spent Soap LyeBy - Product of Soap Manufacture

    Directory of Open Access Journals (Sweden)

    A. U. Israel

    2008-01-01

    Full Text Available Three samples of spent lye from soap manufacturing companies namely Paterson Zochonis Industries (PZ, International Equitable Association (IEA, Kitchen Soap Industries (KSI all in Aba, Abia State of Nigeria and one laboratory simulated sample (SSL were analyzed for the amount of glycerol and residual salts. The amount of glycerol in all the samples increases in the order bleached glycerin > crude glycerin > semi-crude glycerin > treated lye > spent soap lye while the reverse is the order for the amount of residual salts. For the SSL, PZ, IEA and KSL samples, the percentage of recovered glycerol were 91.00, 83.20, 82.80 and 81.40 while the residual salt content (% were 9.80, 6.00, 7.08 and 8.03 respectively. These values compare well with international standards. The results show that the amount of the recovered glycerin and residual salts depend on the quality of the spent lye and the technology employed in the recovery treatment used.

  12. Reports of the Government Industrial Research Institute, Nagoya, Vol. 41, No. 4-5, April-May 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    Contents: production of intermetallic compound by squeeze casting process; ion-exclusion chromatography by uv-detection of alkanolamines using water-glycerin as an eluent; thermostable cellulase from a thermophilic anaerobe: its production in yeast and purification; condensation reactions of substituted indoles with trifluoroacetaldehyde.

  13. Palynological studies in tribe Chlorideae (Poaceae) from salt range ...

    African Journals Online (AJOL)

    Jane

    2011-08-15

    Aug 15, 2011 ... To determine pollen fertility, acetocarmine and glycerin jelly was used by the modified techniques used by Khan and Stace (1999). Anthers were squashed .... World. Kew bulletin additional series 13, Royal Botanic gardens,. Kew. p. 389. Edeoga HO, Okoli BE (1996). Apomictic behaviour in Costus after C.

  14. Centrifugal blood pump 603

    Indian Academy of Sciences (India)

    Centrifugal blood pump 603 pressure obtained for real blood, as shown in figure 6, is a little higher than that for glycerin aqua Solution with the same viscosity as blood. This may indicate the effect of slight non-. Newtonian turbulent flow. The radial whirl motion of the impeller was observed by dual laser position sensors.

  15. Antiviral activity of Aloe vera against herpes simplex virus type 2: An ...

    African Journals Online (AJOL)

    SERVER

    2007-08-06

    Aug 6, 2007 ... In this study we tested the antiviral activity of a crude hot glycerine extract of Aloe vera gel which was grown in Bushehr (Southwest of Iran) against HSV-2 replication in Vero cell line. The extract showed antiviral activity against HSV-2 not only before attachment and entry of virus to the Vero cells but also.

  16. Phytotherapeutic activity of Euphorbia cyparissias extracts on ...

    African Journals Online (AJOL)

    The in vivo study of the efficacy of E. cyparissias concentrations was performed on 35 naturally infested sheep and on 30 bovines parasitized with Ixodes ricinus, sprayed with tincture and glycerinate dilutions (bovines) on days 0 and 7. The results revealed detrimental effects on the survivability of female ticks, the most ...

  17. Dynamics of nitrification and denitrification in root- oxygenated sediments and adaptation of ammonia-oxidizing bacteria to low-oxygen or anoxic habitats

    NARCIS (Netherlands)

    Bodelier, P.L.E.; Libochant, J.A.; Blom, C.W.P.M.; Laanbroek, H.J.

    1996-01-01

    Oxygen-releasing plants may provide aerobic niches in anoxic sediments and soils for ammonia-oxidizing bacteria, The oxygen- releasing, aerenchymatous emergent macrophyte Glycerin maxima had a strong positive effect on numbers and activities of the nitrifying bacteria in its root zone in spring and

  18. Determination of viscosity through terminal velocity: use of the drag force with a quadratic term in velocity

    DEFF Research Database (Denmark)

    Vertchenko, Lev; Vertchenko, Larissa

    2017-01-01

    A correction to the term with quadratic dependency of the velocity in the Oseen´s drag force by a dimensionless factor is proposed in order to determine the viscosity of glycerin through the measurement of the terminal velocity of spheres falling inside the fluid. This factor incorporates the eff...

  19. Modified Alizarin Red S-Alcian Blue Staining for Reptilian Skeleton

    Directory of Open Access Journals (Sweden)

    Muhammad Ja’far Luthfi

    2016-04-01

    Full Text Available Skeletal staining is an important method in anatomical study. The aim of the research was to develop staining and clearing method of Reptilian skeleton using Alizarin Red S-Alcian Blue. The specimen were eviscerated, fixed, stained, cleared, and keep in glycerine solution. This modified double-staining has successfully stain bone and cartilage of Reptilian.

  20. Aproveitamento de co-produtos da cadeia produtiva do biodiesel de mamona

    Directory of Open Access Journals (Sweden)

    Maria Susana Silva

    2010-01-01

    Full Text Available In virtue of the National Program for Biodiesel Production and Use (NPBPU, the commercial scale production in Brazilian semi-arid areas of crops used for biodiesel production has increased and one consequence is the generation of waste that need to target economic and ecologically viable. The main byproducts of biodiesel production chain are the cake and / or meal and glycerin. The present work aims at studying the possibilities to use these surpluses for biodiesel production in value-added products. The conclusions of this work demonstrate that the potential exists for use of castor bean meal in animal feed, such as fertilizer that has the ability to recover degraded areas and to control soil nematodes. Furthermore, it was found that glycerin can be used as fuel with high heat.

  1. Motion of a damped oscillating sphere as a function of the medium viscosity

    International Nuclear Information System (INIS)

    Mendoza-Arenas, J J; Perico, E L D; Fajardo, F

    2010-01-01

    In this paper, an experimental setup for undergraduate courses to study the damped harmonic motion of a sphere inside a fluid as a function of the medium viscosity is presented. To observe the dependence of the oscillation of the sphere on the medium viscosity, different concentrations of glycerin in water were used. The sphere is suspended on the end of a spring and its displacement is indirectly obtained using a force sensor. To describe the sphere motion, a drag force different from that given by Stokes' law is used. Our experimental results fit satisfactorily when semiempirical coefficients are introduced in the model. The frequency and relaxation time of the sphere oscillations diminish as the concentration of glycerin increases. Boundary effects due to the fluid container size are studied. We found that when the container size decreases the oscillations decay more rapidly due to a greater resistance to the motion of the sphere.

  2. Polyesters production from the mixture of phthalic acid, terephthalic and glycerol; Producao de poliesteres a partir da mistura de acido ftalico, tereftalico e glicerol

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, A.L.S.; Oliveira, J.C.; Miranda, C.S.; Boaventura, J.S.; Jose, N.M., E-mail: adrianaequfba@gmail.co [Universidade Federal da Bahia (GECIM/UFBA), Salvador, BA (Brazil). Inst. de Quimica. Grupo de Energia e Ciencias dos Materiais; Carvalho, R.F. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Escola Politecnica. Curso de Mestrado em Engenharia Ambiental Urbana

    2010-07-01

    Glycerin, a byproduct of biodiesel is currently an environmental and economic problem for producers of this renewable fuel in Brazil and in others parts of the world. In order to offer new proposals for recovery, it is used for the manufacture of polyesters used in applications in diverse areas such as construction and automobile industry. This work reports the production of polymer from the mixture of terephthalic and phthalic acid in three different proportions. The polyesters showed good thermal stability, analyzed by TGA and DSC, with an increase proportional to the terephthalic acid content. The X-ray diffraction patterns show that the samples are semi crystalline polymers. The micrographs indicated the presence of a smoother surface in the polyester that has a larger amount of phthalic acid, as reported in the literature. Therefore, the materials showed good thermal properties and morphological characteristics, so it consists in a new alternative to use glycerin. (author)

  3. Polyesters production from the mixture of phthalic acid, terephthalic and glycerol

    International Nuclear Information System (INIS)

    Carvalho, A.L.S.; Oliveira, J.C.; Miranda, C.S.; Boaventura, J.S.; Jose, N.M.; Carvalho, R.F.

    2010-01-01

    Glycerin, a byproduct of biodiesel is currently an environmental and economic problem for producers of this renewable fuel in Brazil and in others parts of the world. In order to offer new proposals for recovery, it is used for the manufacture of polyesters used in applications in diverse areas such as construction and automobile industry. This work reports the production of polymer from the mixture of terephthalic and phthalic acid in three different proportions. The polyesters showed good thermal stability, analyzed by TGA and DSC, with an increase proportional to the terephthalic acid content. The X-ray diffraction patterns show that the samples are semi crystalline polymers. The micrographs indicated the presence of a smoother surface in the polyester that has a larger amount of phthalic acid, as reported in the literature. Therefore, the materials showed good thermal properties and morphological characteristics, so it consists in a new alternative to use glycerin. (author)

  4. Evaluation of Castor Oil Cake Starch and Recovered Glycerol and Development of “Green” Composites Based on Those with Plant Fibers

    Science.gov (United States)

    Guimarães, José Luis; Trindade Cursino, Ana Cristina; Ketzer Saul, Cyro; Sierrakowski, Maria Rita; Ramos, Luiz Pereira; Satyanarayana, Kestur Gundappa

    2016-01-01

    Continuous efforts are being made in some countries for the recovery of crude glycerin (RG/CG) and castor oil cake (COC), the two byproducts of biodiesel production. These are expected to help, not only in addressing environmental safety, but also in adding value to those byproducts, which otherwise may go to waste. Finding ways to utilize those byproducts underlines the main objective of this study. This paper presents the evaluation of (i) COC, glycerin and banana and sugarcane fibers for moisture content; (ii) COC for structural and thermal properties; and (iii) CG for its chemical characteristics. The possibility of using COC and CG with the selected fibers as reinforcement in the development of bio-composites is attempted through thermo-molding. Results revealed enhanced mechanical properties for these composites. The obtained results are discussed in terms of the observed morphology. PMID:28787878

  5. Evaluation of Castor Oil Cake Starch and Recovered Glycerol and Development of "Green" Composites Based on Those with Plant Fibers.

    Science.gov (United States)

    Guimarães, José Luis; Trindade Cursino, Ana Cristina; Ketzer Saul, Cyro; Sierrakowski, Maria Rita; Ramos, Luiz Pereira; Satyanarayana, Kestur Gundappa

    2016-01-27

    Continuous efforts are being made in some countries for the recovery of crude glycerin (RG/CG) and castor oil cake (COC), the two byproducts of biodiesel production. These are expected to help, not only in addressing environmental safety, but also in adding value to those byproducts, which otherwise may go to waste. Finding ways to utilize those byproducts underlines the main objective of this study. This paper presents the evaluation of (i) COC, glycerin and banana and sugarcane fibers for moisture content; (ii) COC for structural and thermal properties; and (iii) CG for its chemical characteristics. The possibility of using COC and CG with the selected fibers as reinforcement in the development of bio-composites is attempted through thermo-molding. Results revealed enhanced mechanical properties for these composites. The obtained results are discussed in terms of the observed morphology.

  6. Green Michael addition of thiols to electron deficient alkenes using KF/alumina and recyclable solvent or solvent-free conditions

    Energy Technology Data Exchange (ETDEWEB)

    Lenardao, Eder J.; Trecha, Danusia O.; Ferreira, Patricia da C.; Jacob, Raquel G.; Perin, Gelson [Universidade Federal de Pelotas (UFPEL), Pelotas, RS (Brazil). Inst. de Quimica e Geociencias. Lab. de Sintese Organica Limpa (LASOL)]. E-mail: lenardao@ufpel.edu.br

    2009-07-01

    A general, clean and easy method for the conjugated addition of thiols to citral promoted by KF/Al{sub 2}O{sub 3} under solvent-free or using glycerin as recyclable solvent at room temperature is described. It was found that the solvent-free protocol is applicable to the direct reaction of thiophenol with the essential oil of lemon grass (Cymbopogon citratus) to afford directly 3,7-dimethyl-3-(phenylthio)oct-6-enal, a potential bactericide agent. The method was extended to other electron-poor alkenes with excellent results. For the solvent-free protocol, the use of microwave irradiation facilitated the procedure and accelerates the reaction. The catalytic system and glycerin can be reused up to three times without previous treatment with comparable activity. (author)

  7. Comparative study of two methods for determining the diffusible hydrogen content in welds

    International Nuclear Information System (INIS)

    Celio de Abreu, L.; Modenesi, P.J.; Villani-Marques, P.

    1994-01-01

    This work presents a comparative study of the methods for measurement of the amount of diffusible hydrogen in welds: glycerin, mercury and gaseous chromatography. The effect of the variables collecting temperatures and times were analyzed. Basic electrodes type AWS E 9018-M were humidified and dried at different times and temperatures in order to obtain a large variation in the diffusible hydrogen contents. The results showed that the collecting time can be reduced when the collecting temperature is raised, the mercury and chromatography methods present similar results, higher than those obtained by the glycerin method, the use of liquid nitrogen in the preparation of the specimens for test is unessential. The chromatography method presents the lower dispersion and is the method that can have the collecting time more reduced by the raising of the collecting temperature. The use of equations for comparison between results obtained by the various methods encountered in the literature is also discussed. (Author) 16 refs

  8. Assessment of Energy Storage Technologies for Army Facilities.

    Science.gov (United States)

    1986-05-01

    pentraerythritol, penta- glycerine, and neopentyl glycol , and is intended for use as thermal storage in passive solar architecture. In a broad interpretation of...Candidate binaries include (1) glycols and :. ,..polyhedric alcohols that are mixed with water and (2) certain alkane-alcohol combina- I .,, tions. Since use...transferred from a lower to a higher temperature and combined with the solid absorbent. Liquid absorbents include sulfuric acid, the alkene glycols , and

  9. A Comprehensive Review on: Transdermal drug delivery systems.

    OpenAIRE

    Kharat, Rekha; Bathe, Ritesh Suresh

    2016-01-01

    Transdermal drug delivery system was introduced to overcome the difficulties of drug delivery through oral route. Despite their relatively higher costs, transdermal delivery systems have proved advantageous for delivery of selected drugs, such as estrogens, testosterone, clonidine and nitro-glycerine. Transdermal delivery provides a leading edge over injectable and oral routes by increasing patient compliance and avoiding first pass metabolism respectively. Topical  administration  of  therap...

  10. CRAQUEAMENTO TÉRMICO DA GLICERINA: UMA PROPOSTA DE EXPERIMENTO PARA QUÍMICA ORGÂNICA

    Directory of Open Access Journals (Sweden)

    Valéria B. Riatto

    2015-05-01

    Full Text Available In this work, an undergraduate organic chemistry experiment based on thermal cracking of glycerin is proposed. The reagent is obtained as a by-product from the practice of biodiesel synthesis, and allows reduction of waste produced in the lab. The main product obtained from thermal cracking was characterized by GC analysis as acrolein. This substance was also identified by chemical derivatization as 2,4-dinitrophenylhydrazone, allowing a combined experiment of identification by synthesis of the derivative.

  11. Phagocytosis and Inflammation: Exploring the effects of the components of E?cigarette vapor on macrophages

    OpenAIRE

    Ween, Miranda P.; Whittall, Jonathan J.; Hamon, Rhys; Reynolds, Paul N.; Hodge, Sandra J.

    2017-01-01

    Abstract E?cigarettes are perceived as harmless; however, evidence of their safety is lacking. New data suggests E?cigarettes discharge a range of compounds capable of physiological damage to users. We previously established that cigarette smoke caused defective alveolar macrophage phagocytosis. The present study compared the effect E?cigarette of components; E?liquid flavors, nicotine, vegetable glycerine, and propylene glycol on phagocytosis, proinflammatory cytokine secretion, and phagocyt...

  12. Nanofluidic Pre-Concentration Devices for Enhancing the Detection Sensitivity and Selectivity of Biomarkers for Human Performance Monitoring

    Science.gov (United States)

    2016-10-17

    antibody by glutaraldehyde coupling, for enabling the selective catalysis of α-naphthyl phosphate (NPP) to the electroactive α-naphthol (NP) product , as...solution at 4 °C overnight. The dialysis product , PSA antibody-ALP conjugate, was then transferred to an Eppendorf tube and mixed with an equal...volume of glycerin and 1% BSA, for storage at 0 °C, prior to the experiments. Cortisol, Triamcinolone, Estradiol, Testosterone and Progesterone were

  13. E-cigarettes also contain detrimental chemicals

    DEFF Research Database (Denmark)

    Tøttenborg, Sandra Søgaard; Holm, Astrid Ledgaard; Wibholm, Niels Christoffer

    2014-01-01

    This article reviews studies dealing with the content of electronic (e-) cigarettes. Based on measurements of the e-juice, the inhaled and the exhaled vapour, it is sound to assume that smoking e-cigarettes might have much less detrimental health effects than smoking conventional cigarettes....... However, propylene glycol and glycerine are abundant in e-cigarettes and although they are generally perceived as relatively harmless, the long-term effects of heavy exposure to these substances are unknown....

  14. E-cigaretten indeholder også skadelige stoffer

    DEFF Research Database (Denmark)

    Tøttenborg, Sandra Søgaard; Holm, Astrid Ledgaard; Wibholm, Niels Christoffer

    2014-01-01

    This article reviews studies dealing with the content of electronic (e-) cigarettes. Based on measurements of the e-juice, the inhaled and the exhaled vapour, it is sound to assume that smoking e-cigarettes might have much less detrimental health effects than smoking conventional cigarettes....... However, propylene glycol and glycerine are abundant in e-cigarettes and although they are generally perceived as relatively harmless, the long-term effects of heavy exposure to these substances are unknown....

  15. Modified, Packaged Tortillas Have Long Shelf Life

    Science.gov (United States)

    Bourland, Charles; Glaus-Late, Kimberly

    1995-01-01

    Tortillas made from modified recipe and sealed in low-pressure nitrogen in foil pouches in effort to increase their shelf life at room temperature. Preliminary tests show that shelf life of these tortillas at least five months; in contrast, commercial tortillas last only few days. Part of water in recipe replaced with glycerin. Particularly necessary to avoid Clostridium botulinum, which grows in anaerobic environments and produces deadly toxin that causes botulism.

  16. Development of Environmentally Benign and Reduced Corrosion Runway Deicing Fluid

    Science.gov (United States)

    2009-08-01

    ESTCP Environmental Security Technology Certification Program FAME Fatty Acid Methyl Ester FFA Free Fatty Acid FPt Freezing Point; first...based on altering the tail-end of the process for making fatty acid methyl ester ( FAME ) by transesterification of triglycerides typically derived from...converted to glycerin while the rest are converted to fatty acid methyl esters ( FAME ) that have traditionally been used in oleochemical industry. Recently

  17. An Investigation of Anaerobic Processes in Fuel/Natural Seawater Environments

    Science.gov (United States)

    2012-02-08

    separated esters and glycerin. Biodiesel contains no sulfur. In the United States the term "biodiesel" is standardized as fatty acid methyl ester ( FAME ...crude oil remaining. Biodiesel is produced from vegetable oils by converting the triglyceride oils to methyl (or ethyl) esters with a process known...water from the environment. Microbial growth in seawater can be limited by nutrients, including carbon. Biodiesel methyl esters are quite sparingly

  18. Obtaining and characterization of a biodegradable polymer starting from the tapioca starch

    International Nuclear Information System (INIS)

    Ruiz Aviles, Gladys

    2006-01-01

    This study focuses on the preparation of tapioca starch biodegradable polymer, processed by blends of starch modified with glycerin and water as plasticizers, by using roll mill and a single-screw extruder in the process. During extrusion, there is a series of variables to control namely: the barrel temperature profile, screw torque and screw rotation speed. Tensile test, differential scanning calorimetric (DSC), thermogravimetric analysis (TGA), Fourier transformer infrared spectroscopy (FTIR) and morphology were used in the process

  19. Fermentative utilization of glycerol residue for the production of acetic acid

    Science.gov (United States)

    Irvan; Trisakti, B.; Hasibuan, R.; Joli, M.

    2018-02-01

    Glycerol residue, frequently known as pitch, is a waste produced from the downstream product of crude glycerine distillation. With the increasing need of pure glycerine in the world, the glycerol residue produced is also increasing. Glycerol residue is a solid waste at room temperature, highly alkaline (pH > 13), corrosive, and categorized as hazardous and poisonous waste. In this research, acetic acid was produced from glycerol residue through the anaerobic fermentation process by using purple non-sulphur photosynthetic bacteria. The purpose of this study was to find out the influence of concentration change of glycerol residue on time and to find out the possibility of glycerol residue to be utilized as acetic acid. In this research, at first 400 g of glycerol residue was diluted with 200 ml of distilled water to change the glycerine phase, from solid to liquid at room temperature, acidified by using hydrochloric acid until pH 2. The top layer formed was fatty acid and triglycerides that should be removed. Meanwhile, the bottom layer was diluted glycerol residue which was then neutralized with caustic soda. To produce acetic acid, glycerol residue with various concentrations, salt, and purple non-sulphur photosynthetic bacteria were put together into a 100 ml bottle which had been previously sterilized, then incubated for four weeks under the light of 40-watt bulb. The result showed that on the 28th day of fermentation, the produced acetic acid were 0.28, 1.85, and 0.2% (w/w) by using glycerine with the concentration of 0.5, 1.0, and 1.5% (w/w), respectively.

  20. Penentuan Jumlah NaOH yang Dibutuhkan pada Unit Gliserin Destilasi dan Pemutihan dengan Parameter Bilangan Penyabunan

    OpenAIRE

    Damanik, Maria E.P

    2015-01-01

    Ecogreen Oleochemicals Co., is one of oleochemical industry manufacturing raw material of palm oil to be fatty acid, glycerine and alcohol. Before processing, characteristic treatment is necessary to do earlier is saponification value. Determination of saponification value can do by using titration method. Given the large number of NaOH, the low number of high influence saponification value. This data according to standart methode of Ecogreen Oleochemicals Co. 102401060

  1. Mongolian Rotifers on Micr oscope Slides: Instructions to Permanent Specimen Mounts from Expedition Material

    OpenAIRE

    Christian D. Jersabek; Erdene Bolortsetseg; Howard L. Taylor

    2010-01-01

    We here describe a method for permanently mounting specimens on microscope slides, as we applied it in the newly established rotifer collection in Ulaanbaatar, Mongolia. The liquid photopolymer NOA 61 was used as a primary sealant for pure glycerine mounts. We furthermore outline simple methods of rotifer narcotization and fi xation in the fi eld that yield, for the majority of species, adequately preserved specimen mat...

  2. High Infestation by Dawestrema cycloancistrioides in Arapaima gigas Cultured in the Amazon Region, Peru

    OpenAIRE

    Mathews, Patrick D.; Malheiros, Antonio F.; Vasquez, Narda D.; Chavez, Milton D.

    2014-01-01

    The aim of this study was to evaluate the presence of Dawestrema cycloancistrioides in semi-intensive fish farming of fingerlings of Arapaima gigas. Between September and November 2013, 60 individuals of A. gigas born in captivity, were collected in three concrete ponds, from a semi-intensive fish farm in the Peruvian Amazon. For the study of sclerotized structures, parasites were fixed in a solution of ammonium picrate glycerine and mounted in Canada balsam. To visualize internal structures,...

  3. Diseño y construcción de un dosificador para el llenado de glicerina en manómetros de tipo bourdon

    OpenAIRE

    Calero Montaguano, Juan Carlos; Paneluisa Montaguano, Edison Rolando

    2015-01-01

    This project is based on providing a service to traders of instrumentation (manometers) within the Ecuadorian oil industrial field, by work experience it is known that the filling of manometers is done manually, where c ontainers are used for filling service, consequence of this procedure raw material waste is generated (glycerin), further filling larger amounts of manometers requires a prolonged period. The objective of the “DESIGN AND CONSTRUCTION OF A FEEDER FOR FI LLING IN BOURDON TYPE GL...

  4. PRETREATING URANIUM FOR METAL PLATING

    Science.gov (United States)

    Wehrmann, R.F.

    1961-05-01

    A process is given for anodically treating the surface of uranium articles, prior to metal plating. The metal is electrolyzed in an aqueous solution of about 10% polycarboxylic acid, preferably oxalic acid, from 1 to 5% by weight of glycerine and from 1 to 5% by weight of hydrochloric acid at from 20 to 75 deg C for from 30 seconds to 15 minutes. A current density of from 60 to 100 amperes per square foot is used.

  5. ANÁLISE MORFOLÓGICA E MICROBIOLÓGICA DO PERICÁRDIO BOVINO CONSERVADO EM AÇÚCAR, GLICERINA, MEL E SAL

    Directory of Open Access Journals (Sweden)

    Antônio Fernando Bariani Júnior

    2014-07-01

    Full Text Available Histological and microbiological comparative analysis of bovine pericardium preserved for 30 and 60 days in glycerin (98%, supersaturated sugar solution (300%, supersaturated solution of salt (150% and unprocessed honey were performed aiming to establish alternative ways of preservation of biological membranes. Samples of pericardium from five cattle were collected in fridge and maintained for up to 60 days in containers with the above mentioned solutions of conservation. For morphological analysis of the constituents of bovine pericardium were performed routine histological techniques associated to two microbiological culture techniques: streaking on the surface of the plate and pour-plate. The supersaturated solution of sugar (300% was the medium of preservation with results closer to the obtained with glycerin (98%, but was unable to prevent microorganisms growth. The unprocessed honey and supersaturated solution of salt (150% had suitable antiseptic characteristics, but failed to effectively conserve the pericardium, with a greater structural disorganization of the connective tissue, indicating advanced process of autolysis after 60 days of storage. It was concluded that glycerin (98% appeared as the most efficient solution when compared to the others evaluated in this study.

  6. Effect of liquid properties on laser ablation of aluminum and titanium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ouyang, Peixuan, E-mail: oypx12@mails.tsinghua.edu.cn [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); Li, Peijie [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Leksina, E.G.; Michurin, S.V. [Skobeltsyn Institute of Nuclear Physics, Moscow State University, Moscow 119992 (Russian Federation); He, Liangju [School of Aerospace, Tsinghua University, Beijing 100084 (China)

    2016-01-01

    Graphical abstract: - Highlights: • Porous surfaces are formed in Al alloy after wet ablation due to phase explosion. • A higher ablation rate is produced in glycerin than that in water and isopropanol. • Effect of liquid properties on mass-removal mechanisms was discussed. • Phase explosion and plasma-induced pressure contribute greatly to mass removal. • Density, heat conductivity and shock impendence of liquid affect ablation rates. - Abstract: In order to study the effect of liquid properties on laser ablation in liquids, aluminum 5A06 and titanium TB5 targets were irradiated by single-pulse infrared laser in isopropanol, distilled water, glycerin and as a comparison, in air, respectively. Craters induced by laser ablation were characterized using scanning electron and white-light interferometric microscopies. The results show that for liquid-mediated ablation, craters with porous surface structures were formed in aluminum target through phase explosion, while no micro-cavities were formed in titanium target owing to high critical temperature of titanium. In addition, ablation rates of aluminum and titanium targets vary with types of ambient media in accordance with such sequence: air < isopropanol < water < glycerin. Further, the influence of liquid properties on material-removal mechanisms for laser ablation in liquid is discussed. It is concluded that the density, thermal conductivity and acoustical impedance of liquid play a dominant role in laser ablation efficiency.

  7. Piper betle LEAVES EXTRACT PATCH: EVALUATION OF ANTIBACTERIAL ACTIVITY, RELEASE PROFILE OF EUGENOL, AND LOCAL TOLERANCE

    Directory of Open Access Journals (Sweden)

    Mufrod Mufrod

    2016-08-01

    Full Text Available Piper betle leaf in extract form is more effective than crude drug. Eugenol is a component in the extract that has antibacterial activity but irritate. Patch of piper betle leaf extract was used on the mucosa to make oral cavity hygiene. Antibacterial activity was influenced by the release of eugenol from the patch. Release enhancer substances (RES such as glycerin, propylen glicol and tween 80 were added in patch formulation to increase the release of active substances. The aim of the research was to investigate the physicochemical properties, eugenol release profiles, and local tolerance test of the patch. Extract of piper betle leaf was made using infundation method. Patch was made according to the variation concentration of extract (1, 2 and 4% and RES (glycerine, propylen glycol and tween 80 using chitosan as vehicle. Patch produced solvent casting method. Patch obtained was tested for swelling index, folding endurance, surface pH, antibacterial activity, release of eugenol, and local tolerance. Data obtained were analyzed descriptively. The result showed that the addition of RES did not affect the surface pH but increase the water absorption with in inconsistent way except patch with tween 80. The flexibility (folding endurance value increased, and the highest amount of eugenol released was achieved by patch using propylen glicol. Patch with tween 80 and glycerin for all extract concentration and patch with 1% extract concentration using propylen glycol showed medium sensation (local tolerance, and patch with 2 and 4% extract using propylen glycol showed severe sensation.

  8. The virucidal effects against murine norovirus and feline calicivirus F4 as surrogates for human norovirus by the different additive concentrations of ethanol-based sanitizers.

    Science.gov (United States)

    Akasaka, Tempei; Shimizu-Onda, Yuko; Hayakawa, Satoshi; Ushijima, Hiroshi

    2016-03-01

    Since human norovirus is non-cultivable, murine norovirus and feline calicivirus have been used as surrogates. In this study, the virucidal effects of ethanol-based sanitizers with different concentrations of additives (malic acid/sodium malate, glycerin-fatty acid ester) against murine norovirus and feline calicivirus F4 were examined. The ethanol-based sanitizers at pH 7 showed sufficient virucidal effects, but glycerin-fatty acid ester included in ethanol-based sanitizers at pH 4 or 6 reduced the virucidal effects against murine norovirus. The ethanol-based sanitizers containing malic acid/sodium malate inactivated feline calicivirus F4 in shorter time, but there is no difference between ethanol-based sanitizers with and without glycerin-fatty acid ester. Traditionally, feline calicivirus has been used for long time as a surrogate virus for human norovirus. However, this study suggested that murine norovirus and feline calicivirus F4 had different sensitivity with the additive components of ethanol-based sanitizers. Therefore, using feline calicivirus alone as a surrogate for human norovirus may not be sufficient to evaluate the virucidal effect of sanitizers on food-borne infections caused by human norovirus. Sanitizers having virucidal effects against at least both murine norovirus and feline calicivirus may be more suitable to inactivate human norovirus. Copyright © 2015. Published by Elsevier Ltd.

  9. Development of Carrageenan Hydrogel as a Sustained Release Matrix Containing Tocotrienol-Rich Palm-Based Vitamin E

    International Nuclear Information System (INIS)

    Yee, C.M.; Zafarizal Aldrin Azizul Hasan; Norashikin Ahmad; Hazimah, A.H.

    2016-01-01

    Topically applied hydrogel system as a general therapeutic mask for transdermal delivery of hydrophobic actives is not efficient due to the differences in polarity between the actives and the polymer network. This work presents a study on developing hydrogels based on carrageenan as a matrix for the delivery of a hydrophobic type of active, i.e. tocotrienol-rich palm-based vitamin E (TRPE) into the skin. The strength and flexibility of the hydrogel were increased by the inclusion of guar gum, potassium citrate and glycerine. The thermogravimetric analysis (TGA) results indicated a higher quantity of water in the hydrogel with glycerine while differential scanning calorimetry (DSC) showed three types of water molecules existed in the hydrogel. The hydrogel was non-irritating according to OECD Test Guideline No. 439 for in vitro skin irritation test. The hydrogel with TRPE fluids was able to permeate the polysulfone membrane and bioavailability of TRPE improved with the inclusion of PEG-40 hydrogenated castor oil mixture. Therefore, a carrageenan-based hydrogel with locust bean, guar gum, glycerine, potassium citrate and TRPE was successfully developed with good strength and flexibility and without any potential irritancy. The good bioavailability of TRPE-loaded in the hydrogel can be used for skin care application. (author)

  10. Influence of flocculating agents and structural vehicles on the physical stability and rheological behavior of nitrofurantoin suspension.

    Science.gov (United States)

    Moghimipour, Eskandar; Salimi, Anayatollah; Rezaee, Saeed; Balack, Maryam; Handali, Somayeh

    2014-05-01

    Nitrofurantoin is a nitrofuran antibiotic that has been used for treatment of urinary tract against positive and negative bacteria. The aim of this study was to evaluate the effect of structural vehicles and flocculating agents on physical stability and rheological behavior of nitrofurantoin suspension. To formulate the suspensions, the effect of glycerin and polysorbate 80 as wetting agents was evaluated and their particle sizes were determined using the sieve method. Then to achieve controlled flocculation, sodium citrate and aluminum chloride were added. After choosing the suitable wetting and flocculating agents, structural vehicles such as sodium carboxyl methyl cellulose and Veegum were evaluated individually and in combination. In addition, the effect of sorbitol on density of continuous phase and some physical stability parameters such as sedimentation volume, degree of flocculation and ease of redispersion of the suspensions were evaluated. After incorporation of structural vehicles, the rheological properties of formulations were also determined to find their flow behavior. According to the results, glycerin (0.2%) and sodium citrate (0.3%) had the best effect on the suspension stability as wetting and flocculating agents, respectively. Rheological properties of formulations showed pseudoplastic behavior with some degree of thixotropy. In conclusion, the suspension containing Veegum 1%, sodium carboxy methyl cellulose 1%, glycerine 0.2%, sodium citrate 0.3% and sorbitol 20 % was chosen as the most physically stable formulation.

  11. Green polyurethane synthesis by emulsion technique: a magnetic composite for oil spill removal

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Raphael Maria Dias da; Hungerbühler, Gabriela; Saraiva, Thiago; De Jong, Gabriel; Moraes, Rafael Silva; Ferreira, Luciana Spinelli; Souza Junior, Fernando Gomes de, E-mail: fgsj@ufrj.br [Universidade Federal do Rio de Janeiro (LaBioS/UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Biopolímeros e Sensores; Furtado, Evandro Goncalves [Alfa Rio Química Ltda., Duque de Caxias, RJ (Brazil); Silva, Fabrício Machado [Universidade de Brasília (UnB), Brasília, DF (Brazil); Oliveira, Geiza Esperandio de [Coordenacao de Pos-Graduacao e Pesquisa de Engenharia (PEN/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil)

    2017-07-01

    After the consolidation of the Brazilian biodiesel industry, issues related to the final destination of the glycerin, the by-product from the biodiesel industrial process, drawing the attention of several researchers. There are several uses to this byproduct. Among them, the obtaining of polymers, such as polyurethane (PU), are very encouraged since the glycerin ca be used, as well as the castor oil, in the replacement of petrochemical polyols. The aim of this work was to propose a new route for the obtainment of a petroleum sorbent based on polyurethane resin from glycerin and castor oil, through the emulsion technique. In addition, maghemite (γ-Fe{sub 2}O{sub 3}) was mixed to the polymer matrix, producing a magnetic composite, able to make easier the oil cleanup process. The products synthesized were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, simultaneous Thermogravimetry (TGA) and Differential scanning calorimetry (DSC), Optical microscopy, Scanning electron microscopy (SEM). In addition, magnetic force and oil removal capability tests were also performed. The magnetic material was used to remove oil from water, exhibited a good oil removal capability. In a typical test, 1g of the composite containing 5wt% of maghemite was able to remove 10g of oil from water. (author)

  12. Facile Synthesis and Optical Properties of Small Selenium Nanocrystals and Nanorods

    Science.gov (United States)

    Jiang, Fengrui; Cai, Weiquan; Tan, Guolong

    2017-06-01

    Selenium is an important element for human's health, small size is very helpful for Se nanoparticles to be absorbed by human's body. Here, we present a facile approach to fabrication of small selenium nanoparticles (Nano-Se) as well as nanorods by dissolving sodium selenite (Na2SeO3) in glycerin and using glucose as the reduction agent. The as-prepared selenium nanoparticles have been characterized by X-ray diffraction (XRD), UV-Vis absorption spectroscopy and high resolution transmission electron microscope (HRTEM). The morphology of small Se nanoparticles and nanorods have been demonstrated in the TEM images. A small amount of 3-mercaptoproprionic acid (MPA) and glycerin play a key role on controlling the particle size and stabilize the dispersion of Nano-Se in the glycerin solution. In this way, we obtained very small and uniform Se nanoparticles; whose size ranges from 2 to 6 nm. This dimension is much smaller than the best value (>20 nm) ever reported in the literatures. Strong quantum confinement effect has been observed upon the size-dependent optical spectrum of these Se nanoparticles.

  13. Green polyurethane synthesis by emulsion technique: a magnetic composite for oil spill removal

    International Nuclear Information System (INIS)

    Costa, Raphael Maria Dias da; Hungerbühler, Gabriela; Saraiva, Thiago; De Jong, Gabriel; Moraes, Rafael Silva; Ferreira, Luciana Spinelli; Souza Junior, Fernando Gomes de; Silva, Fabrício Machado; Oliveira, Geiza Esperandio de

    2017-01-01

    After the consolidation of the Brazilian biodiesel industry, issues related to the final destination of the glycerin, the by-product from the biodiesel industrial process, drawing the attention of several researchers. There are several uses to this byproduct. Among them, the obtaining of polymers, such as polyurethane (PU), are very encouraged since the glycerin ca be used, as well as the castor oil, in the replacement of petrochemical polyols. The aim of this work was to propose a new route for the obtainment of a petroleum sorbent based on polyurethane resin from glycerin and castor oil, through the emulsion technique. In addition, maghemite (γ-Fe 2 O 3 ) was mixed to the polymer matrix, producing a magnetic composite, able to make easier the oil cleanup process. The products synthesized were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, simultaneous Thermogravimetry (TGA) and Differential scanning calorimetry (DSC), Optical microscopy, Scanning electron microscopy (SEM). In addition, magnetic force and oil removal capability tests were also performed. The magnetic material was used to remove oil from water, exhibited a good oil removal capability. In a typical test, 1g of the composite containing 5wt% of maghemite was able to remove 10g of oil from water. (author)

  14. Evaluation and Characterization of Biodiesels Obtained Through Ethylic or Methylic Transesterification of Tryacylglicerides in Corn Oil

    Directory of Open Access Journals (Sweden)

    Douglas Queiroz Santos

    2014-06-01

    Full Text Available This work was devoted to the transesterification of corn oil either with methyl or ethyl alcohol and to the characterization of the biodiesels (composed by FAME—fatty acid methyl esters—or FAEE—fatty acid ethyl esters, respectively produced. As an initial hypothesis, it was argued whether or not the two alcohols, both with short molecular chains, would impart significant differences to the chemical characteristics of the two biodiesels from corn oil. The most common properties of the biodiesels were evaluated by determining corresponding parameters for acid value, peroxide value, water content, oxidative stability, free and total glycerin, kinematic viscosity at 40 ℃ and density at 20 ℃, for both chemical routes, FAME and FAEE. In general, values were found to be well within the recommended limits for commercial biodiesel, in accordance with the Brazilian, European and American standard recommendations, except only for the oxidative stability. The methyl biodiesel presented acidity of 0.08 mg KOH/g; peroxide index, 23.77 meq/kg; oxidation stability, 3.10 h; water content, 297.1 mg/kg; total glycerin, 0.092 %; free glycerin, 0.009 %; viscosity, 4.05 mm2/s and density, 878.7 kg/m. The methyl biodiesel presented acidity of 0.11 mg/ KOH; peroxide index, 22.39 meq/kg; oxidation stability, 2.13 h; water content, 264.8 mg/kg; total glycerin, 0.25 %; free glycerin, 0.02 %; viscosity, 4.37 mm2/s and density, 874.0 kg/m. From a direct inspection of chemical data for the two products prepared via the two chemical routes, it can be drawn that values of the physical and chemical parameters for both, methyl and ethyl biodiesels, are essentially similar, except for the oxidative stability. However, the oxidative stability can be suitably adjusted by adding an anti-oxidizing agent to the ethyl biodiesel medium. The two biodiesels are thus promising alternatives to fully replace or to be admixed to the mineral diesel. Relatively to the pure petrol

  15. A novel approach to determine the thermal transition of gum powder/hydro-gels using dynamic mechanical analysis

    Science.gov (United States)

    Nagamadhu, M.; Jeyaraj, P.; Kumar, G. C. Mohan

    2018-04-01

    The dynamic characterization of materials plays a major role in the present area. The many researchers are worked on solid materials and its characterization, it can be tested using dynamic mechanical analyzer (DMA), however, no such work on powder a semiliquid samples. The powder and liquid samples can also easily characterization as like solid samples using DMA. These powder samples are analyzed with a material pocket method which can be used to accurately determine very low levels of variation in powder properties, due to the high sensitivity of DMA to glass transitions. No such DMA studies on hydrogel and Gum powders. The gum powders are used in various applications start from food industries, pharmacy, natural gums paste, biomedical applications etc. among all this applications gum Ghatti is one of the powders using for varies applications. Around 50 milligrams of Ghatti powders are placed inside material pocket and analyzed storage modulus (G'), loss modulus (G″) and tan delta (δ). Also, understand the curing and glass transition effect using water, glycerin and superplastic from room temperature to 200°C. The result shows that storage modulus decreases with increase in temperature in pure Ghatti powder. The surprising improvement in storage modulus was found with an increase in temperature with addition of water, glycerin, and superplastic. However, loss modulus and tan delta are also having very significant influence and also shows a clear peak of the tan delta. The loss modulus results were found to be improved by adding solidifying agents, along with this water and superplastic better influence. But glycerine found to be hydrogel in nature and thermodynamic properties are much influenced by frequency.

  16. Fabrication of hemispherical liquid encapsulated structures based on droplet molding

    Science.gov (United States)

    Ishizuka, Hiroki; Miki, Norihisa

    2015-12-01

    We have developed and demonstrated a method for forming spherical structures of a thin polydimethylsiloxane (PDMS) membrane encapsulating a liquid. Liquid encapsulation can enhance the performance of microelectromechanical systems (MEMS) devices by providing deformability and improved dielectric properties. Parylene deposition and wafer bonding are applied to encapsulate liquid into a MEMS device. In parylene deposition, a parylene membrane is directly formed onto a liquid droplet. However, since the parylene membrane is stiff, the membrane is fragile. Although wafer bonding can encapsulate liquid between two substrates, the surface of the fabricated structure is normally flat. We propose a new liquid encapsulation method by dispensing liquid droplets. At first, a 20 μl PDMS droplet is dispensed on ethylene glycol. A 70 μl glycerin droplet is dispensed into a PDMS casting solution layer. The droplet forms a layer on heated ethylene glycol. Glycerin and ethylene glycol are chosen for their high boiling points. Additionally, a glycerin droplet is dispensed on the layer and surrounded by a thin PDMS casting solution film. The film is baked for 1 h at 75 °C. As the result, a structure encapsulating a liquid in a flexible PDMS membrane is obtained. We investigate the effects of the volume, surface tension, and guide thickness on the shape of the formed structures. We also evaluated the effect of the structure diameter on miniaturization. The structure can be adapted for various functions by changing the encapsulated liquid. We fabricated a stiffness-tunable structure by dispensing a magnetorheoligical fluid droplet with a stiffness that can be changed by an external magnetic field. We also confirmed that the proposed structure can produce stiffness differences that are distinguishable by humans.

  17. Use of nuclear photoemulsions for low energy deuteron detection in vacuum and helium medium in case of time exposure

    International Nuclear Information System (INIS)

    Barit, I.Ya.; Balashko, Yu.G.; Dul'kova, L.S.; Zavarzina, V.P.; Romanova, T.A.

    1975-01-01

    An investigation is described of a possibility of recording 700 to 950 keV deuterons with fine-grain type T-3 and P-9 photoemulsion in vacuum and in a helium atmosphere, allowance being made for a possible variation in photolayer parameters during long exposures of an 10 to 14 days. To eliminate the exfoliation of emulsions from the glass as a result of staying for long in vacuum, they have been first kept in an spirit-glycerine mixture and then dried in a special drier at room temperature. Such pretreatment may result in changes in photoemulsion moderating capability as well as in the shrinkage coefficient. Therefore the moderating capability and the shrinkage coefficients of the photoemulsions treated by the method described above have been estimated. The obtained results show that the treatment with spirit-glycerine mixture may cause an increse in track length not more than by 1.5 to 3%, if at all, this value being within the accuracy limits of track measurements. The shrinkage coefficient for plates soaked with spirit-glycerine mixture turns out to be equal to that of untreated ones. Investigation of a possible change in emulsion layer thickness during long exposure in helium atmosphere (240 hours) and in vacuum (approximately 100 hours) show a 15% decrease in the shrinkage coefficient. Investigation of the effect of long staying of plates in vacuum and dry helium atmosphere indicates the decrease in track length due to pumping various additives the emulsions contain. The investigation carried out proves the possibility of using types T-3 and P-9 nuclear emulsions for recording low-energy charged particles at long exposures in vacuum (approximately 0.01 torr) and a dry neutral gas medium accounting for possible changes in the photolayer nuclear emulsions for recording low-energy charged particles at long exposures in vacuum (approximately 0.01 torr) and a dry neutral gas medium accounting for possible changes in the photolayer [ru

  18. Update state of suppository bases’ assortment and factors of their selection

    Directory of Open Access Journals (Sweden)

    T. M. Litvinenko

    2014-04-01

    Full Text Available Introduction. At the present moment compounding of suppositories is a promising tendency considering that this dosage form has some advantages and is an alternative to the oral and parenteral medications. However not only active substances but excipients (suppository bases also play a great role for achievement of desirable therapeutical effect. The aim of this article is to research an assortment of suppository bases, their advantages and disadvantages and to present factors of selection. Fatty bases are perhaps the most frequently employed suppository bases, principally because cocoa butter is a member of this group of substances. Among the other fatty or oleaginous materials used in suppository bases there are many hydrogenated fatty acids of vegetable oils such as palm kernel oil and cottonseed oil. Also, fat-based compounds containing compounds of glycerin with the higher molecular weight fatty acids, such as palmitic and stearic acids, may be found in fatty suppository bases. The main members of water-soluble bases are polyethylene glycols and poloxomers. Various combinations of polyethylene glycols may be combined by fusion, using two or more of the various types to achieve a suppository base of the desired consistency and characteristics. Glycerin-gelatin base is composed of glycerin (5 p., gelatin (1 p., and purified water (2 p.. Diphylic suppository bases contain hydrophylic and hydrophobic parts and make it possible to incorporate water solutions and oleaginous ingredients. Selection of the base involves the nature of the active substance, manufacturing procedures and physical-chemical characteristics. Conclusions. It is apparent then, that a great number of suppository bases have been developed but none of them answers the requirements. So the search of new suppository bases is main problem of pharmaceutical technology. Also the necessity of new domestic bases development has been noted.

  19. Preparation and Evaluation of a Modified Mohs Paste Mixed with Zinc Oxide 10% Topical Oil-Based Ointment.

    Science.gov (United States)

    Tsuruta, Minako; Miyoshi, Takanori; Tsuruyama, Moeko; Matsumoto, Saori; Yamashina, Takuya; Irie, Kenji; Matsuo, Naomi; Itonaga, Tomomi; Hiraki, Yoichi; Kawamata, Yosei

    2018-05-01

    The skin fixative used in Mohs chemosurgery contains zinc chloride and is referred to as Mohs paste (MP). However, MP shows a remarkable change in rheological characteristics after its preparation. To prepare an MP with stable rheological characteristics, we prepared a modified MP (mMP) using zinc oxide 10% single ointment (Zn _ointment ), which is an oil-based ointment. We evaluated mMP by determining its rheological characteristics, depth of tissue fixation, and observation of the tissue surface after treatment. The viscosity of mMP increased after three months. However, the treatment-dependent viscosity of mMP could be obtained by mixing with glycerin. The viscosity and spreadability of mMP _3mth , which was three months after preparation, were 1992.0 ± 376.5 Pa·s and 2.1 ± 0.1 cm, respectively. In contrast, the viscosity and spreadability of MP mixed with glycerin were 436.9 ± 0.0 Pa·s and 2.8 ± 0.0 cm, respectively. The fixed invasion depth of MP was significantly higher than that of mMP (p < 0.05). This study of a mixture of MP and Zn _ointment showed that the viscosity of mMP could be adjusted with glycerin. Also, the tissue fixation of mMP progressed slowly compared with that of MP. This finding suggests that mMP is effective and safe for Mohs treatment.

  20. Microbicide excipients can greatly increase susceptibility to genital herpes transmission in the mouse

    Directory of Open Access Journals (Sweden)

    Sun Mianmian

    2010-11-01

    Full Text Available Abstract Background Several active ingredients proposed as vaginal microbicides have been shown paradoxically to increase susceptibility to infection in mouse genital herpes (HSV-2 vaginal susceptibility models and in clinical trials. In addition, "inactive ingredients" (or excipients used in topical products to formulate and deliver the active ingredient might also cause epithelial toxicities that increase viral susceptibility. However, excipients have not previously been tested in susceptibility models. Methods Excipients commonly used in topical products were formulated in a non-toxic vehicle (the "HEC universal placebo", or other formulations as specified. Twelve hours after exposure to the excipient or a control treatment, mice were challenged with a vaginal dose of HSV-2, and three days later were assessed for infection by vaginal lavage culture to assess susceptibility. Results The following excipients markedly increased susceptibility to HSV-2 after a single exposure: 5% glycerol monolaurate (GML formulated in K-Y® Warming Jelly, 5% GML as a colloidal suspension in phosphate buffered saline, K-Y Warming Jelly alone, and both of its humectant/solvent ingredients (neat propylene glycol and neat PEG-8. For excipients formulated in the HEC vehicle, 30% glycerin significantly increased susceptibility, and a trend toward increased HSV-2 susceptibility was observed after 10% glycerin, and 0.1% disodium EDTA, but not after 0.0186% disodium EDTA. The following excipients did not increase susceptibility: 10% propylene glycol, 0.18%, methylparaben plus 0.02% propylparaben, and 1% benzyl alcohol. Conclusions As reported with other surfactants, the surfactant/emulsifier GML markedly increased susceptibility to HSV-2. Glycerin at 30% significantly increased susceptibility, and, undiluted propylene glycol and PEG-8 greatly increased susceptibility.

  1. HOMOIMPLANTE ORTOTÓPICO DE TENDÃO CALCÂNEO EM CÃES: CONSERVAÇÃO, ASSEPSIA E IMPLANTAÇÃO ORTHOTOPIC HOMOLOGOUS COMMON CALCANEOUS TENDON GRAFT IN DOGS: CONSERVATION, ASEPSIS AND IMPLANTATION

    Directory of Open Access Journals (Sweden)

    Alceu Gaspar Raiser

    2001-02-01

    Full Text Available Foi elaborado um modelo experimental de conservação, assepsia e implantação de tendão homólogo ortotópico, para avaliar a resposta orgânica, em 48 cães. Os implantes foram conservados em glicerina a 98%, durante 45 dias a seis meses e, após, reidratados e submetidos à ação anti-séptica do iodo durante 24h antes da implantação. A avaliação clínica e histopatológica após 11, 22, 44 e 132 dias de evolução não evidenciou qualquer sinal de infecção ou rejeição. Tendões homólogos ortotópicos conservados em glicerina a 98% estão indicados para corrigir perdas tendíneas.An experimental model of conservation, asepsis and implantation of homologous glycerine 98%-stored tendon graft is presented in order to evaluate the tissue reaction to implantation in 48 dogs. Grafts were preverved in sterile glycerin from 45 days to six months period. Before implantation grafts were placed in isotônic saline with iodine, during 24h period for rehydration and asepsis. Clinical evaluation and histopathologic analisis of biopsies were made at 11st , 22nd, 44th and 132nd post-operative day. There was not evidence of infection or graft rejection. Orthotopic homologous glycerine-stored tendon graft are indicated in reconstructive tendon surgery.

  2. Production of ethyl ester from crude palm oil by two-step reaction using continuous microwave system

    Directory of Open Access Journals (Sweden)

    Sukritthira Ratanawilai

    2011-02-01

    Full Text Available The esterification of free fatty acids (FFA in vegetable oils with alcohol using an acid catalyst is a promising methodto convert FFA into valuable ester and obtain a FFA-free oil that can be further transesterified using alkali bases. In thiswork, the direct esterification reaction of FFA in crude palm oil to ethyl ester by continuous microwave was studied and theeffects of the main variables involved in the process, amount of catalyst, reaction time and the molar ratio oil/ alcohol, wereanalyzed. The optimum condition for the continuous esterification process was carried out with a molar ratio of oil to ethanol1:6, using 1.25%wt of H2SO4/oil as a catalyst, microwave power of 78 W and a reaction time 90 min. This esterification processshows that the amount of FFA was reduced from 7.5%wt to values around 1.4 %wt. Similar results were obtained followingconventional heating at 70°C, but only after a reaction time of 240 min. The esterified crude palm oil is suitable to perform thetransesterification process. Transesterification of the esterified palm oil has been accomplished with a molar ratio of oil toethanol of 1:8.5, 2.5%wt of KOH as a catalyst, a microwave power of 78 W, and a reaction time of 7 min. In addition, theproblem of glycerin separation was solved by mixing 10%wt of pure glycerin into the ethyl ester to induce the glycerin fromthe reaction to separated. This two-step esterification and transesterification process provided a yield of 78%wt with anester content of 97.4%wt. The final ethyl ester product met with the specifications stipulated by ASTM D6751-02.

  3. Fundamental Studies on Ambient Temperature Creep Deformation Behavior of Alpha and Alpha-Beta Titanium Alloys

    Science.gov (United States)

    1994-02-15

    Solutions [49] A-Etch 25 (mL) Hydrofluoric Acid (HF 50%) 25 Nitric Acid Cone (HN03) 50 Glycerine R-Etch 18.5 gm (17 mL) Benzalkonium Chloride 35 (mL... Reduction Project (0704-0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave Blank) 2. REPORT DATE 1994 3. REPORT TYPE AND DATES COVERED Final 4...K and a 60% reduction in area was given for all of the alloys. This work was found to be sufficient to recrystallize all of the alloys within 12

  4. Development of MgB2 superconductor wire with high critical current

    International Nuclear Information System (INIS)

    Kim, Chan Joong; Jun, Byung Hyuk; Park, Soon Dong; Kim, Nam Kyu; Kim, Yi Jeong; Yi, Ji Hye; Lee, Ji Hyun; Tan, Kai Sin

    2009-07-01

    The MgB 2 superconductor with smaller grain size could improve its critical properties by providing flux pinning centers with high grain boundary density. The effects of C doping such as charcoal, paper ash and glycerin on the superconducting properties was investigated for in situ processed MgB 2 samples using low purity semi-crystalline B powder. The results show a decrease in Tc and an enhancement of Jc at high fields for the C-doped samples as compared to the un-doped samples. A combined process of a mechanical ball milling and liquid glycerin (C 3 H 8 O 3 ) treatment of B powder has been conducted to enhance the superconducting properties of MgB 2 . The mechanical ball milling was effective for grain refinement, and a lattice disorder was easily achieved by glycerin addition. With the combined process, the critical properties was further increased due to a higher grain boundary density and a greater C substitution. To get fine grain structure of MgB 2 with high critical current properties, mechanical milling for as-received B powder and low temperature solid-state reaction of 550 or 600 .deg. C were attempted to in situ powder-in-tube processed MgB 2 /Fe wires. The critical current properties of the MgB 2 wires using the milled B powder were enhanced due to a smaller grain size and an increased volume of the superconducting phase. The solid-state reaction of a low temperature process for the samples using the milled B powder resulted in a poorer crystallinity with a smaller grain size, which improved superconducting properties. We established the system to measure the transport current properties of the MgB 2 wires. The field dependence of the transport Jc was evaluated for the MgB 2 wires heat-treated at different heat treatment conditions using ball-milled and glycerin-treated B powder. The MgB 2 magnet was developed and the AC loss of MgB 2 wire was also investigated. A conduction cooling device to cool the MgB 2 coil down to 4 K has been fabricated and the

  5. Study of reduction methods for irradiation on oral mucositis. The examination of reduction methods for mucosal failure

    International Nuclear Information System (INIS)

    Tonogi, Morio; Yamane, Genyuki; Aoyagi, Yutaka; Hasegawa, Azusa; Mizoe, Junetsu; Tsujii, Hirohiko

    2004-01-01

    Reduction methods for irradiation on oral mucosa examined concerning in acute phase of the carbon ion radiotherapy for head and neck malignancies. We enforced a mechanical teeth and gingival cleaning as an Oral hearth care and gargled a polaprezinc with sodium alginate, and azulene- lidocaine with glycerin sodium as a oral linces before radiation. The response of the mucosal failure was reduced compare with no care group. In this Result, we considered that oral hearth care for prevention of infection, and mucosa protection by the drug was important factor. (author)

  6. Synthesis of polyacrylonitrile (PAN) with different stereoregularity by urea radiation inclusion polymerization and its application to carbon fiber

    Energy Technology Data Exchange (ETDEWEB)

    Fujikura, Yoshiaki; Minakawa, Masaaki [Yamagata Univ., Yonezawa (Japan). Faculty of Engineering; Makuuchi, Keizo; Matsuo, Masaru; Yoshii, Fumio

    1998-01-01

    Application to carbon fiber started in this Year. In this paper, a spinning and calcination process are explained. Fiber was obtained by wet spinning of the PAN solution. Ten solvents were tested and the results proved that dimethyl sulfoxide (DMSO) was the best solvent. Glycerine was used as a coagulating bath. The thin fiber (10 to 50 denier) was produced under the conditions of about 20wt% concentration at about 110degC. Heat-treat temperature was about 270 to 275degC. The viscosity-tacticity relationship and T{sub sol} vs. inverse tacticity were shown in the paper. (S.Y.)

  7. Bone preparation at the KCCAMS laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Beaumont, Will, E-mail: wbeaumon@uci.ed [Earth System Science Dept., University of California, B321 Croul Hall, Irvine, CA 92697-3100 (United States); Beverly, Robert; Southon, John [Earth System Science Dept., University of California, B321 Croul Hall, Irvine, CA 92697-3100 (United States); Taylor, R.E. [Department of Anthropology, University of California, Riverside, CA 92521 (United States)

    2010-04-15

    Collagen purification by ultrafiltration is becoming widely accepted as a superior {sup 14}C sample preparation method for removing environmental contamination from archaeological bone. We present an overview of bone sample preparation methods used at the KCCAMS laboratory, UC Irvine. Methods development data are also discussed, including results of tests of gelatinization temperature, evaluation of 10 kDa vs. 30 kDa molecular weight (MW) ultrafiltration, improvements to ultrafilter cleaning methods, tests of ultrafilter memory, and ultrafilter glycerin contamination. These tests were not intended to be exhaustive, but rather to show how standard procedures can be validated and improved with relatively little effort.

  8. Capacity of ensilage of Jatropha curcas L. cake to degrade forbol esters

    OpenAIRE

    Oliveira, André Soares de; Schwambach, Thiago Ivan; Sinhorin, Adilson Paulo; Oliveira, Márcia Rodrigues Carvalho; Alessi, Karine Claudia; Oliveira Filho, Francisco Antônio de; Pina, Douglas dos Santos

    2012-01-01

    The objective of this study was to evaluate the capacity of the ensilage of Jatropha curcas L. expeller cake to reduce the phorbol esters and its effect on fermentative losses, by adding soluble carbohydrates or microbial inoculants. The design was completely randomized with four replications in a 3 × 2 factorial arrangement, with three sources of soluble carbohydrates (SC, control, 50 g sucrose/kg or 50 g crude glycerin/kg as fed) and two doses of microbial inoculants (MI, 0 or 5 × 10(5) ufc...

  9. Simulation of Polygeneration Systems

    Directory of Open Access Journals (Sweden)

    Francesco Calise

    2016-11-01

    Full Text Available This Special Issue aims at collecting the recent studies dealing with polygeneration systems, with a special focus on the possible integration of different technologies into a single system, able to convert one or multiple energy sources into energy services (electricity, heat and cooling and other useful products (e.g., desalinized water, hydrogen, glycerin, ammonia, etc.. Renewable sources (solar, wind, hydro, biomass and geothermal, as well as fossil fuels, feeding advanced energy systems such as fuel cells and cogeneration systems, are considered. Special attention is paid to control strategies and to the management of the systems in general. Studies including thermoeconomic analyses and system optimizations are presented.

  10. Applicability of Stokes method for measuring viscosity of mixtures with concentration gradient

    Directory of Open Access Journals (Sweden)

    César Medina

    2017-12-01

    Full Text Available After measuring density and viscosity of a mixture of glycerin and water contained in a vertical pipe, a variation of these properties according to depth is observed. These gradients are typical of non-equilibrium states related to the lower density of water and the fact that relatively long times are necessary to achieve homogeneity. In the same pipe, the falling velocity of five little spheres is measured as a function of depth, and then a numerical fit is performed which agrees very well with experimental data. Based on the generalization of these results, the applicability of Stokes method is discussed for measuring viscosity of mixtures with a concentration gradient.

  11. (3R,6R,12R,20S,24S-3,6,12-Triacetyl-20,24-epoxydammarane-3,6,12,25-tetraol

    Directory of Open Access Journals (Sweden)

    Qing-Guo Meng

    2011-01-01

    Full Text Available The title compound, C36H58O8, was prepared from 20(S-protopanaxatriol, which was degraded from Panax quinquefolium saponin with sodium in glycerine, extracted and seperated by flash chromatography. Three six-membered rings are in chair conformations, the five-membered ring is in an envelope form and the tetrahydrofuran ring has a conformation intermediate between half-chair and envelope. In the crystal, molecules are linked by O—H...O hydrogen bonds, and C—H...O contacts also occur. The absolute structure was assigned on the basis of the synthesis.

  12. METHOD OF ELECTROPOLISHING URANIUM

    Science.gov (United States)

    Walker, D.E.; Noland, R.A.

    1959-07-14

    A method of electropolishing the surface of uranium articles is presented. The process of this invention is carried out by immersing the uranium anticle into an electrolyte which contains from 35 to 65% by volume sulfuric acid, 1 to 20% by volume glycerine and 25 to 50% by volume of water. The article is made the anode in the cell and polished by electrolyzing at a voltage of from 10 to 15 volts. Discontinuing the electrolysis by intermittently withdrawing the anode from the electrolyte and removing any polarized film formed therein results in an especially bright surface.

  13. Identification of chemical compounds present in different fractions of Annona reticulata L. leaf by using GC-MS.

    Science.gov (United States)

    Rout, Soumya P; Kar, Durga M

    2014-01-01

    GC-MS analysis of fractions prepared from hydro-alcoholic extract of Annona reticulata Linn (Family Annonaceae) leaf revealed the presence of 9,10-dimethyltricyclo[4.2.1.1(2,5)]decane-9,10-diol; 4-(1,5-dihydroxy-2,6,6-trimethylcyclohex-2-enyl)but-3-en-2-one; 3,7-dimethyl-6-nonen-1-ol acetate; 9-octadecenamide,(Z)-; glycerine; D-glucose,6-O-α-D-galactopyranosyl-; desulphosinigrin and α-methyl-D-mannopyranoside as few of the major compounds in different fractions. The presence of these compounds in the plant has been identified for the first time.

  14. Estudo comparativo da resistência à tração do peritônio (bovino, eqüino, suíno e canino a fresco e conservado em glicerina

    Directory of Open Access Journals (Sweden)

    Leila Cristina Batista

    1996-12-01

    equine, swine, bovine and canine peritoneus to be used as implants, and to determine the nature of their histological structures. Standard pieces, 6 mm width - 50 mm lenght, both fresh and glycerinated for 15, 30 and 60 days were submitted to the ratio of maximum strength. Tests were carried out using Universal Assay Machine. Right after the strength tests, the membrane pieces were fixed in formaline and processed for histological examination after hematoxylin-eosin staining. Considering the stretching range caused by traction, data showed that the different membranes did not present the same resistance, and rupture points among the 4 samples were also different.

  15. Studi Sintesis Metil Ester Asam Lemak Dari Pitch Cair Melalui Tahap Reaksi Esterifikasi Dan Transesterifikasi

    OpenAIRE

    Turnip, Roselprida

    2015-01-01

    Pitch liquid having high Free Fatty Acid (FFA) derived from by product of process Palm Kernel Oil (PKO) became Fatty acid & Glycerine. The Reaction of making fatty acid methyl esters (FAME) from Pitch liquid having high FFA min 25,60% was investigated in two step. The acid-catalyzed (H2SO4(p)) esterification follow to Transesterification by the base catalyzed (KOH) methanolysis with mol ratio of methanol and TG of Pitch liquid 6 : 1, The first step reduced the FFA 1.01% with reaction time ...

  16. Effect of components (polymer, plasticizer and solvent as a variable in fabrication of diclofenac transdermal patch

    Directory of Open Access Journals (Sweden)

    Chetna Modi

    2012-01-01

    Full Text Available Transdermal drug delivery influence consumer acceptance and marked increase in bioavailability of some drugs which undergoes hepatic first-pass metabolism. Fabrication of transdermal patch requires lots of attention regarding the amount of components used for it. Because of varied nature of polymer and plasticizer, transdermal patches have different properties and different drug release. This study is on the basis to evaluate the amount to be needed for fabrication of diclofenac transdermal patch. Study shows that Hydroxy Propyl Methyl Cellulose has great influence on transdermal patch, if it is used alone in combination with glycerin or PEG-4000 plasticizer.

  17. The development of polymeric pellicles with gentamicine sulfate for therapeutic correction of cervical erosion (pseudoerosion

    Directory of Open Access Journals (Sweden)

    T. M. Litvinenko

    2014-08-01

    Full Text Available Introduction.Cervical erosionsoccur in 12-15%gynaecological diseases. Erosion is a damage of epithelialmucous membrane or skin. Therapy of patients with cervical erosionsis based on selection of pathogeneticsubstantiative method of treatment. Bathes and irrigations with 20% protargol, alum, carbolic acid, potassium permanganate are used. But some authors admit the destructive influence of these procedures. Using of tampons with 10% sintomycine emulsion, cod liver oil, sea-buckthorn oil,kalanchoe sap, propolis, vagotil, cigerol, galantamine also doesn’t give desirable result. Recently polymeric pellicleswith antibacterial substances are widely used. The most perspective in this route are aminoglycoside antibiotics. That is why we chose gentamicine sulfate (broad-spectrum aminoglycoside antibiotic. The aim of study is the development of the optimal composition of vaginal pellicleswith gentamicine sulfate for gynaecological practice, scientifically substantiation of excipients: polymeric base and plasticizer. Results and discussion.Polymeric bases and plasticizers influence on gentamicine sulfate releasing from polimericpellicleshas been studied. Research on choice of optimal composition has been carried out by two-factor experiment plan. The next bases and plasticizers have been used: methylcellulose, sodium carboxymethylcellulose, soluble biopolymer, gelatin; glycerine, propylenglycol, polyethylene glycol, twin 80. Gentamicine sulfate content was 80 mg in one pellicle. Gentamicine sulfate releasing from polimericpellicleshas been investigated by the Kruvchinsky method, concentration of active substance has been detected after 45 min. As a result it has been established that base makes essential influence on the gentamicine sulfate releasing (Fexp.52,88>Ftabl. 3,9. The best plasticizer is glycerin and the most optimal base is gelatin. So the optimal composition for vaginal films has been chosen: Gentamicine sulfate0,08 g Glycerin0,7 g Gelatin0

  18. Palynomorphs in Holocene sediments from a paleolagoon in the coastal plain of extreme southern Brazil

    OpenAIRE

    Ebráilon Masetto; Maria Luisa Lorscheitter

    2014-01-01

    This paper presents the results of a qualitative palynological analysis of a 140 cm-thick section of Holocene sediments from a paleolagoon, representing the last 2600 years, taken from an outcrop at Hermenegildo Beach (33º42'S; 53º18'W), located in the municipality of Santa Vitória do Palmar, in the state of Rio Grande do Sul, Brazil. Samples were treated with hydrochloric acid, hydrofluoric acid and potassium hydroxide, after which they were subjected to acetolysis and mounted on glycerin-co...

  19. Treatment of proctalgia fugax with topical nitroglycerin: report of a case.

    Science.gov (United States)

    Lowenstein, B; Cataldo, P A

    1998-05-01

    We report a single case of proctalgia fugax that responded to 0.3 percent nitroglycerin ointment. Case report. A single case of proctalgia fugax responded to topical application of 0.3 percent nitro glycerin ointment with no significant side effects. Nitroglycerin ointment is a newly described treatment for several painful anal conditions. We describe a single case of levator spasm or proctalgia fugax responding to topical application of nitroglycerin. This is only a single case report, and conclusive evidence awaits completion of a controlled clinical trial.

  20. Method for providing a low density high strength polyurethane foam

    Science.gov (United States)

    Whinnery, Jr., Leroy L.; Goods, Steven H.; Skala, Dawn M.; Henderson, Craig C.; Keifer, Patrick N.

    2013-06-18

    Disclosed is a method for making a polyurethane closed-cell foam material exhibiting a bulk density below 4 lbs/ft.sup.3 and high strength. The present embodiment uses the reaction product of a modified MDI and a sucrose/glycerine based polyether polyol resin wherein a small measured quantity of the polyol resin is "pre-reacted" with a larger quantity of the isocyanate in a defined ratio such that when the necessary remaining quantity of the polyol resin is added to the "pre-reacted" resin together with a tertiary amine catalyst and water as a blowing agent, the polymerization proceeds slowly enough to provide a stable foam body.

  1. A study of the effect of certain formulation variables on the mucoadhesive properties of per oral sucralfate suspensions

    Science.gov (United States)

    Dobrozsi, Douglas Joseph

    1999-10-01

    The primary objective of this research was to evaluate the effect of formulation variables on the ability of a suspension of the material sucralfate to be triggered to gel by components of the gastrointestinal fluid and in so doing, act as an in situ gelling mucoadhesive liquid. The particle size and type of sucralfate raw material, suspension pH, ionic strength, and presence of the humectant suspension aid glycerin were studied. Sucralfate materials were prepared in sizes ranging from under 50 nanometers up to 60 microns. Included were conventional powders, and a gel form prepared by controlled precipitation from acid solution. Sucralfate zero point of charge was determined by titration to be pH 4.8--4.9 for powder, and 5--5.3 for gel. The gel was found to exist as aggregates of a relatively uniform, spherical, nanoparticulate colloidal sol with particle size in the range of 50 to 400 nanometers. The aggregates could be disrupted by high pressure homogenization so that individual colloidal particles could be detected in water dispersion. Rheologic and mucoadhesion evaluations of suspensions were conducted. Models were established for in vitro mucoadhesion by rheologic synergism with mucin, and for mucosal coating and retention on rat esophagus ex vivo. Experiments with marketed sucralfate suspensions indicated that rheologic synergism with gastric mucin correlated with ex vivo mucoretention and agreed directionally with published human mucoretention. Aqueous suspension viscosity was found to be increased by KCl, by increasing sucralfate concentration, and for the gel by adjusting pH near the zero point of charge. Viscosity also increased with decreasing sucralfate particle size but rheologic synergism did not correlate with particle size. Glycerin increased rheologic synergism with mucin. Suspension viscosity and rheologic synergism were much greater under all conditions for sucralfate gel suspensions than for sucralfate powder suspensions. Disruption of gel

  2. Pollution prevention in the oil and soap industry: a case study

    Energy Technology Data Exchange (ETDEWEB)

    Abou-Elela, S.I. [National Research Center, Gizza (Egypt). Water Pollution Control Dept.; Zaher, F. [National Research Center, Gizza (Egypt). Fats and Oil Dept.

    1998-12-31

    Industrial audit of a complex oil and soap factory has been carried out. The factory produces edible oils, fatty acids, soap, crude, industrial and pharmaceutical glycerin, powdered detergents, animal fodder, sodium and potassium silicates, sodium hypochlorite and hypochloric acid. The audit shows that there were a wide range of pollution prevention opportunities which could be implemented with significant financial advantages for the factory as well as reducing environmental pollution. Cost benefits for the recommended environmental improvements have been estimated. Many of the improvements had short payback periods. (author)

  3. Pollution prevention in the oil and soap industry: a case study

    International Nuclear Information System (INIS)

    Abou-Elela, S.I.; Zaher, F.

    1998-01-01

    Industrial audit of a complex oil and soap factory has been carried out. The factory produces edible oils, fatty acids, soap, crude, industrial and pharmaceutical glycerin, powdered detergents, animal fodder, sodium and potassium silicates, sodium hypochlorite and hypochloric acid. The audit shows that there were a wide range of pollution prevention opportunities which could be implemented with significant financial advantages for the factory as well as reducing environmental pollution. Cost benefits for the recommended environmental improvements have been estimated. Many of the improvements had short payback periods. (author)

  4. Oleochemical industry future through biotechnology.

    Science.gov (United States)

    Abdelmoez, Wael; Mustafa, Ahmad

    2014-01-01

    Lipases are the most widely used class of enzymes in organic synthesis. Enzymatic processes have been implemented in a broad range of industries as they are specific, save raw materials, energy and chemicals, environmentally friendly and fast in action compared to conventional processes. The most notable benefit is the moderate process temperature and pressure with no unwanted side reactions. In the past two decades, intensive research was carried out towards enzymatic synthesis of oleochemicals. This review has a sharp focus on the current implemented enzymatic processes for producing different oleochemicals such as fatty acids, glycerin, biodiesel, biolubricant and different alkyl esters via different processes including hydrolysis, esterification, transesterification and intraesterification.

  5. A double stage dry-wet-fermentation process for a fast and safe digestion of different kinds of organic material

    International Nuclear Information System (INIS)

    Busch, G.; Sieber, M.; Buschmann, J.; Burkhardat, M.

    2009-01-01

    The fermentation of organic material is a four-step-process. It is admissible to merge the first two steps (hydrolysis and acidification) to hydrolysis in general and the last two steps (aceto genesis and methano genesis) to methano genesis. The Brandenburg University of Technology in Cottbus has devised a double stage dry-wet-fermentation process for fast and safe anaerobic degradation. Using these processes, it is possible to decompose different kinds of organic material like renewable material (e. g. maize silage), waste (e. g. household-waste) and industrial material (e. g. glycerine). (Author)

  6. Simple TLC-screening of acylglycerol levels in biodiesel as an alternative to GC determination.

    Science.gov (United States)

    Fontana, J D; Zagonel, G; Vechiatto, W W; Costa, B J; Laurindo, J C; Fontana, R; Pelisson, L; Jorge, B H; Lanças, F M

    2009-10-01

    Thin layer chromatography (TLC) stained with hot acidic p-anisaldehyde, is an interesting, fast, and low-cost technique to monitor main lipid contaminants such as triacylglycerols, diacylglycerols, and monoacylglycerols in biodiesel. These acylglycerols are detectable by the proposed planar chromatographic method, provided the content of the contaminants exceeds the limits recommended by the international norms applicable to biodiesel quality/specification, namely 0.25% in mass for total combined glycerin. The TLC data are confirmed by gas chromatography of the methyl esters of soy oil.

  7. Uniformly thinned optical fibers produced via HF etching with spectral and microscopic verification.

    Science.gov (United States)

    Bal, Harpreet K; Brodzeli, Zourab; Dragomir, Nicoleta M; Collins, Stephen F; Sidiroglou, Fotios

    2012-05-01

    A method for producing uniformly thinned (etched) optical fibers is described, which can also be employed to etch optical fibers containing a Bragg grating (FBG) uniformly for evanescent-field-based sensing and other applications. Through a simple modification of this method, the fabrication of phase-shifted FBGs based on uneven etching is also shown. The critical role of how a fiber is secured is shown, and the success of the method is illustrated, by differential interference contrast microscopy images of uniformly etched FBGs. An etched FBG sensor for the monitoring of the refractive index of different glycerin solutions is demonstrated.

  8. Vegetable oils as diesel fuel

    International Nuclear Information System (INIS)

    Fedeli, E.; Girelli, A.

    2001-01-01

    During the seventies, one of the recurring fuels crisis gave rise to research on alternative sources and among them to the idea of utilizing vegetable oils. The research work made clear that the oils cannot be utilized as such but they must be transformed in simple esters, eliminating the problems arising from the presence of the glycerine. The Experiment Stations of the Industry, Commerce and Handicraft Department of the Italian Government, by request of the last one, in the '70/'80 has done a successful experimentation that is presented in the paper [it

  9. Anaerobic co-digestion of animal waste: swine manure and tuna fish waste

    Energy Technology Data Exchange (ETDEWEB)

    Otero, L.; Alvarez, J. A.; Lema, J. M.

    2009-07-01

    Anaerobic digestion has become an established and proven technology for the treatment of solid wastes. Co-digestion offers several possible ecological, technology and economical advantages. Anaerobic co-digestion can increase CH{sub 4} production of manure diesters in a 50-200% according to the operation conditions and the co-substrates used. Last September 2007, PROBIOGAS project started up with the objective of improving the production and use of biogas from co-digestion of farming, agricultural and industrial waste. Our research group takes part in the study of co-digestion of swine manure firstly with tuna fish waste and secondly with glycerine (bio diesel production waste). (Author)

  10. Ultrasensitive mass sensor fully integrated with complementary metal-oxide-semiconductor circuitry

    DEFF Research Database (Denmark)

    Forsén, Esko Sebastian; Abadal, G.; Ghatnekar-Nilsson, S.

    2005-01-01

    Nanomechanical resonators have been monolithically integrated on preprocessed complementary metal-oxide-semiconductor (CMOS) chips. Fabricated resonator systems have been designed to have resonance frequencies up to 1.5 MHz. The systems have been characterized in ambient air and vacuum conditions...... and display ultrasensitive mass detection in air. A mass sensitivity of 4 ag/Hz has been determined in air by placing a single glycerine drop, having a measured weight of 57 fg, at the apex of a cantilever and subsequently measuring a frequency shift of 14.8 kHz. CMOS integration enables electrostatic...

  11. Evaluation of skin moisturizer effects using terahertz time domain imaging

    Science.gov (United States)

    Martinez-Meza, L. H.; Rojas-Landeros, S. C.; Castro-Camus, E.; Alfaro-Gomez, M.

    2018-02-01

    We use terahertz time domain imaging for the evaluation of the effects of skin-moisturizers in vivo. We evaluate three principal substances used in commercial moisturizers: glycerin, hyaluronic acid and lanolin. We image the interaction of the forearm with each of the substances taking terahertz spectra at sequential times. With this, we are able to measure the effect of the substances on the hydration level of the skin in time, determining the feasibility of using THz imaging for the evaluation of the products and their effects on the hydration levels of the skin.

  12. Preparation and characterisation of superheated drop detectors

    International Nuclear Information System (INIS)

    Krishnamoorthy, P.

    1989-01-01

    Basic mechanism of bubble nucleation in superheated drops with respect to minimum energy of radiation and temperature is discussed. Experimental details and techniques for the preparation of Superheated Drop Detectors (SDDs) is explained. For the sample preparation, homogeneous composition of polymer (Morarfloc) and glycerine was used as the host medium and three different refrigerants Mafron-21, Mafron-12 and Mafron-11/12 (50:50) were chosen as the sensitive liquids. A pressure reactor developed at Health and Safety Laboratory is used for dispersing the sensitive liquid drops in the homogeneous composition under pressure. Some of the imporatant detector characteristics were studied. (author). 26 refs., 9 figs., 1 tab

  13. Biodiesel purification methodology produced in the RECOPE experimental plant, using ion exchange resins

    International Nuclear Information System (INIS)

    Calderon Hernandez, Teresita

    2016-01-01

    A methodology was proposed for the biodisel purification of crude palm oil produced in a plant located on the Refinadora Costarricense de Petroleo (RECOPE) campus in Alto de Ochomogo, using ion exchange resins. A comparison between two resins was carried out: the USF C-211H, which had been acquired together with the RECOPE experimental plant and the PD206 resin, which was in the process of being acquired at the time of starting the project. The biodisel was eluted by glass columns packed with each resin, to determine the saturation of the same. The percentage of free and bound glycerin and the presence of soaps were analyzed as response variables. With the results obtained, it was determined that the PD206 resin is more efficient in the removal of glycerin, soaps and methanol than the resin USF C-211H. However, neither of the two resins diminishes the acidity of the biodisel. A biodisel sample was eluted by the PD206 resin and the quality of the obtained product was analyzed. A flash point of 145 degrees was obtained. A total acid number of 0.82 mg KOH / G was shown, no presence of water or sediment was observed. The percentage value of carbon residue was 0.01% m / m, the cloud point was 12 degrees, the density at 15 degrees was 0.8713 g / cm 3 , the viscosity at 40 degrees was 2.75 mm 2 /s; the stability to oxidation was 14.5 h, the percentage of free glycerin was 0.01% m / m and the percentage of total glycerin was 0.06% m / m, finally a percentage of Fatty Acids Methyl Esters (FAME) of 98,6%. Of the analyzed parameters, all are within the limits established in the Reglamento Tecnico Centroamericano except the acidity value, which exceeds the maximum value of 0.05 mg KOH / g sample. An economic analysis was carried out to evaluate which resin provides the best option to complete the purification process of the biodisel produced. The PD206, despite being more expensive, purifies a larger volume of biodiesel, so for a better negotiation in the purchase price, this

  14. Finding viscosity of liquids from Brownian motion at students' laboratory

    International Nuclear Information System (INIS)

    Greczylo, Tomasz; Debowska, Ewa

    2005-01-01

    Brownian motion appears to be a good subject for investigation at advanced students' laboratory [1]. The paper presents such an investigation carried out in Physics Laboratory II at the Institute of Experimental Physics of Wroclaw University. The experiment has been designed to find viscosity of liquids from Brownian motion phenomenon. Authors use modern technology that helps to proceed with measurements and makes the procedure less time and effort consuming. Discussion of the process of setting up the experiment and the results obtained for three different solutions of glycerin in water are presented. Advantages and disadvantages of the apparatus are pointed out along with descriptions of possible future uses

  15. Gelatin/piassava composites treated by Electron Beam Radiation

    International Nuclear Information System (INIS)

    Takinami, Patricia Yoko Inamura; Shimazaki, Kleber; Moura, Esperidiana Augusta Barretos de; Mastro, Nelida Lucia del; Colombo, Maria Aparecida

    2010-01-01

    Piassava (Attalea funifera Mart) fiber has been investigated as reinforcement for polymer composites with potential for practical applications. The purpose of the present work was to assess the behavior of specimens of piassava fiber and gelatin irradiated with electron beam at different doses and percentage. The piassava/gelatin specimens were made with 5 and 10% (w/w) piassava fiber, gelatin 25% (w/w), glycerin as plasticizer and acrylamide as copolymer. The samples were irradiated up to 40 kGy using an electron beam accelerator, at room temperature in presence of air. Preliminary results showed mechanical properties enhancement with the increase in radiation dose. (author)

  16. [Theophile-Jules Pelouze (1807-1867) was one of the French pharmacists who has the most contributed to the evolution of the organic chemisty in the first half of the 19th century].

    Science.gov (United States)

    Arnaud, Pascal

    2015-03-01

    Through some examples of his works, realized between 1833 and 1845 (studies on the tannin, the reaction of etherification, and on the nature of the chemical function of the glycerin), this article tries to bring to light his scientific approach. This one is not only based on the immediate analysis and the elementary analysis, but also on the study of characteristic chemical reactions, which are going to give him information onto the chemical nature and the constitution of the molecules which he studies. This approach will lead him finally to use these reactions not only in an analytical purpose but also in a purpose of synthesis.

  17. Use of the by-products of the biodiesel productive chain; Aproveitamento dos subprodutos da cadeia produtiva do biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Moebus, Fernando; Almeida, Silvio Carlos Anibal de [Universidade Federal do Rio de Janeiro (DEM/EP/UFRJ), RJ (Brazil). Escola Politecnica. Dept. de Engenharia Mecanica], Emails: f_moebus@polis.ufrj.br, silvioa@gmail.com

    2010-07-01

    This paper performs an economical analysis of the incomes obtained with the using of byproducts of productive chain of bio diesel. Two technologies will be studied as follows: the commercialization of the residues (peels, cake) in the form of briquettes, and glycerin. A cost spreadsheet was developed for quantification the costs for obtain the biodiesel from the different raw-materials in a process of batch. Besides the cost of raw material and others inputs (catalyst and methanol), it will be analysed the main factors that influences the final costs of product a the generated incomes with commercialization of by-products.

  18. Effects of ionizing radiation on gelatine films added with antioxidant

    International Nuclear Information System (INIS)

    Kraide, Felipe H.; Inamura, Patricia Y.; Mastro, Nelida L. del

    2011-01-01

    This work evaluates the effect of ionizing radiation on the gelatin films in presence of antioxidant. Gelatin solutions of glycerine and poly vinil alcohol, with and without the addition were prepared until the complete homogenization. The films were irradiated with 20 and 40 kGy in a electron accelerator, in the presence of air and at the room temperature. The use of ionizing radiation and the addition of antioxidant changed the properties of the film. The result of water absorption test revealed that with increasing of radiation dose occurred a reduction in the absorption, suggesting that happen a reticulation

  19. Radiation effect of ethylene/vinyl alcohol copolymer

    International Nuclear Information System (INIS)

    Liu Meihua; Jilin Univ., Changchun; Deng Pengyang; Sun Jiazhen; Dong Lisong; Sun Guoen; Zhang Wanxi

    2006-01-01

    The radiation effect of ethylene-vinyl alcohol copolymer (EVOH), EVOH/glycerin blend was studied by solvent extraction, gel permeation chromatography (GPC) and Fourier transform infrared spectrum (FTIR) methods. Samples were irradiated up to 1800 kGy at room temperature under N 2 . The results show that degradation is the main reaction in pure EVOH. Trace gel content could be found in E151 irradiated to at least 800 kGy, and only 5.9% gel content was found in the sample irradiated to 1200 kGy. While trace gel content could be found in F101 irradiated to at least 1800 kGy, the different gelation doses of E151 and F101 are due to different contents of vinyl alcohol units. Unsaturation structure can be found in the irradiated EVOH. The content increased at first, and then decreased, with the dose. The existence of double bond enhances the radiation efficiency of EVOH. For EVOH/glycerin blend, the gel content was higher than that of pure EVOH when the absorbed dose exceeds 800 kGy, and the gel content increased with the absorbed dose. But it cannot enhance radiation efficiency of EVOH as water. (authors)

  20. Evaluation of different magnetic resonance imaging contrast materials to be used as dummy markers in image-guided brachytherapy for gynecologic malignancies*

    Science.gov (United States)

    Sales, Camila Pessoa; Carvalho, Heloisa de Andrade; Taverna, Khallil Chaim; Pastorello, Bruno Fraccini; Rubo, Rodrigo Augusto; Borgonovi, Arthur Felipe; Stuart, Silvia Radwanski; Rodrigues, Laura Natal

    2016-01-01

    Objective To identify a contrast material that could be used as a dummy marker for magnetic resonance imaging. Materials and Methods Magnetic resonance images were acquired with six different catheter-filling materials-water, glucose 50%, saline, olive oil, glycerin, and copper sulfate (CuSO4) water solution (2.08 g/L)-inserted into compatible computed tomography/magnetic resonance imaging ring applicators placed in a phantom made of gelatin and CuSO4. The best contrast media were tested in four patients with the applicators in place. Results In T2-weighted sequences, the best contrast was achieved with the CuSO4-filled catheters, followed by saline- and glycerin-filled catheters, which presented poor visualization. In addition (also in T2-weighted sequences), CuSO4 presented better contrast when tested in the phantom than when tested in the patients, in which it provided some contrast but with poor identification of the first dwell position, mainly in the ring. Conclusion We found CuSO4 to be the best solution for visualization of the applicator channels, mainly in T2-weighted images in vitro, although the materials tested presented low signal intensity in the images obtained in vivo, as well as poor precision in determining the first dwell position. PMID:27403016

  1. Pulse electrochemical machining on Invar alloy: Optical microscopic/SEM and non-contact 3D measurement study of surface analyses

    International Nuclear Information System (INIS)

    Kim, S.H.; Choi, S.G.; Choi, W.K.; Yang, B.Y.; Lee, E.S.

    2014-01-01

    Highlights: • Invar alloy was electrochemically polished and then subjected to PECM (Pulse Electro Chemical Machining) in a mixture of NaCl, glycerin, and distilled water. • Optical microscopic/SEM and non-contact 3D measurement study of Invar surface analyses. • Analysis result shows that applied voltage and electrode shape are factors that affect the surface conditions. - Abstract: In this study, Invar alloy (Fe 63.5%, Ni 36.5%) was electrochemically polished by PECM (Pulse Electro Chemical Machining) in a mixture of NaCl, glycerin, and distilled water. A series of PECM experiments were carried out with different voltages and different electrode shapes, and then the surfaces of polished Invar alloy were investigated. The polished Invar alloy surfaces were investigated by optical microscope, scanning electron microscope (SEM), and non-contact 3D measurement (white light microscopes) and it was found that different applied voltages produced different surface characteristics on the Invar alloy surface because of the locally concentrated applied voltage on the Invar alloy surface. Moreover, we found that the shapes of electrode also have an effect on the surface characteristics on Invar alloy surface by influencing the applied voltage. These experimental findings provide fundamental knowledge for PECM of Invar alloy by surface analysis

  2. Fully Noncontact Wave Propagation Imaging in an Immersed Metallic Plate with a Crack

    Directory of Open Access Journals (Sweden)

    Jung-Ryul Lee

    2014-01-01

    Full Text Available This study presents a noncontact sensing technique with ultrasonic wave propagation imaging algorithm, for damage visualization of liquid-immersed structures. An aluminum plate specimen (400 mm × 400 mm × 3 mm with a 12 mm slit was immersed in water and in glycerin. A 532 nm Q-switched continuous wave laser is used at an energy level of 1.2 mJ to scan an area of 100 mm × 100 mm. A laser Doppler vibrometer is used as a noncontact ultrasonic sensor, which measures guided wave displacement at a fixed point. The tests are performed with two different cases of specimen: without water and filled with water and with glycerin. Lamb wave dispersion curves for the respective cases are calculated, to investigate the velocity-frequency relationship of each wave mode. Experimental propagation velocities of Lamb waves for different cases are compared with the theoretical dispersion curves. This study shows that the dispersion and attenuation of the Lamb wave is affected by the surrounding liquid, and the comparative experimental results are presented to verify it. In addition, it is demonstrated that the developed fully noncontact ultrasonic propagation imaging system is capable of damage sizing in submerged structures.

  3. Radial Fingering in a Porous Medium Digitation radiale dans un milieu poreux

    Directory of Open Access Journals (Sweden)

    Ni W.

    2006-11-01

    Full Text Available The theory of immiscible radial displacement in a Hele-Shaw cell is extended to the case of a porous medium contained between two closely-spaced parallel plates, and experiments are described for the displacement of glycerine by paraffin oil in such a system. Data are presented for the number of fingers, the breakthrough time, and the glycerine recovery, for a range of flowrates varying through three orders of magnitude. Good agreement between theory and experiment is observed. La théorie s'appliquant aux déplacements radiaux dans les cellules Hele-Shaw a été étendue à un système qui consiste en une couche mince de milieux poreux encapsulée entre deux plaques en verre. Dans cet article, on examine les déplacements de la glycérine par de l'huile de paraffine. En faisant varier le débit de l'huile de paraffine dans un intervalle de trois ordres de grandeur, on a étudié les variables telles que le nombre de digitations, le temps de percée et le taux de récupération de la glycérine. On a observé un bon accord entre la théorie et les résultats expérimentaux.

  4. Integrated volarization of spent coffee grounds to biofuels

    Directory of Open Access Journals (Sweden)

    Mebrahtu Haile

    2014-06-01

    Full Text Available Biodiesel is a renewable energy source produced from natural oils and fats, and is being used as a substitute for petroleum diesel. The aim of this study was to investigate the potential of using spent coffee grounds for biodiesel production and its by-products to produce pelletized fuel, which is expected to help the biodiesel production process achieve zero waste. For this experiment, spent coffee grounds sample was collected from Kaldis coffee, Addis Ababa, Ethiopia. Extraction of the spent coffee grounds oil was then conducted using n-hexane, ether and mixture of isopropanol to hexane ratio (50:50 %vol, and resulted in oil yield of 15.6, 17.5 and 21.5 %w/w respectively. A two-step process was used in biodiesel production with conversion of about 82 %w/w. The biodiesel quality parameters were evaluated using the American Standard for Testing Material (ASTM D 6751. The major fatty acid compositions found by Gas chromatography were linoleic acid (37.6%, palmitic acid (39.8%, oleic (11.7%, and stearic acid (8.6%. In addition, solid waste remaining after oil extraction and glycerin ratio (glycerin content from 20-40% was evaluated for fuel pellet (19.3-21.6 MJ/Kg applications. Therefore, the results of this work could offer a new perspective to the production of biofuel from waste materials without growing plants and/or converting food to fuel.

  5. Capacity of ensilage of Jatropha curcas L. cake to degrade forbol esters

    Directory of Open Access Journals (Sweden)

    André Soares de Oliveira

    2012-06-01

    Full Text Available The objective of this study was to evaluate the capacity of the ensilage of Jatropha curcas L. expeller cake to reduce the phorbol esters and its effect on fermentative losses, by adding soluble carbohydrates or microbial inoculants. The design was completely randomized with four replications in a 3 × 2 factorial arrangement, with three sources of soluble carbohydrates (SC, control, 50 g sucrose/kg or 50 g crude glycerin/kg as fed and two doses of microbial inoculants (MI, 0 or 5 × 10(5 ufc Lactobacillus plantarum + 3.33 × 10(5 ufc Propionibacterium per g as fed. Twenty-four mini-silos (982 cm³ of polyvinyl chloride were created and opened after 60 days of fermentation at room temperature. The pre-hydrated Jatropha curcas L. cake (282 g of water/kg contained 0.424 mg of phorbol esters/g of dry matter. Ensiling reduced the phorbol esters in 47.4%, on average, regardless of the SC or MI. There was no interaction effect between SC and MI on effluent, gases or total dry matter losses. However, both losses were increased when SC were added, and it was higher with glycerin that than sucrose. The addition of MI reduced all fermentation losses. The process of ensiling, although partially to reduce the phorbol esters of pre-hydrated Jatropha curcas L. cake, is not indicated as a biodestoxification procedure.

  6. Enhance heat transfer in the channel with V-shaped wavy lower plate using liquid nanofluids

    Directory of Open Access Journals (Sweden)

    Azher M. Abed

    2015-03-01

    Full Text Available The heat transfer and flow characteristics in corrugated with V-shape lower plate using nanofluids are numerically studied. The computations are performed on uniform heat flux over a range of Reynolds number (Re 8000–20,000. The governing equations are numerically solved in the domain by a finite volume method (FVM using the k–ε standard turbulent model. Studies are carried out for different types of nanoparticles Al2O3,CuO, SiO2 and ZnO with different volume fractions in the range of 0–4%. Three different types of base fluid (water, glycerin, ethylene glycol are also examined. Results indicated that the average Nusselt number for nanofluids is greater than that of the base liquid. The SiO2 nanofluid yields the best heat transfer enhancement among all other type of nanofluids. Heat transfer enhancement increase with increases the volumetric concentration, but it is accompanied by increasing pressure drop values. Moreover, the average Nusselt number increases with an increase in Reynolds number and volume concentration. The SiO2–glycerin nanofluid has the highest Nusselt number compared with other base fluids. The present study shows that these V-shaped wavy channels have advantages by using nanofluids and thus serve as promising candidates for incorporation into efficient heat transfer devices.

  7. Electron beam effects on gelatin polymer

    Energy Technology Data Exchange (ETDEWEB)

    Inamura, Patricia Y.; Shimazaki, Kleber; Souza, Clecia de M.; Moura, Esperidiana A.B.; Mastro, Nelida L. del, E-mail: patyoko@yahoo.co [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Colombo, Maria A., E-mail: mascolombo@yahoo.com.b [Faculdade de Tecnologia da Zona Leste, Sao Paulo, SP (Brazil)

    2009-07-01

    The main field of electron-beam radiation processing applications is the modification of polymeric material. Polymer development includes new pathways to produce natural polymers with better mechanical and barrier properties and thermal stability. The aim of this paper was to investigate the behavior of a gelatin/acrylamide polymer treated by electron-beam radiation. Gelatin is a heterogeneous mixture of water-soluble proteins of high average molecular mass derived by hydrolytic action from animal collagen, a fibrous insoluble protein, which is widely found in nature as the major constituent of skin, bones and connective tissue. Hydrolyzed collagen is composed of a unique sequence of amino acids, characterized particularly by the high content of glycine, proline and hydroxyproline. Among biomaterials, gelatin is an interesting material because is a partially crystalline polymer and has a relatively low melting point. Samples of gelatin together with glycerin as plasticizer and acrylamide as copolymer were irradiated with doses of 10 kGy and 40 kGy, using an electron beam accelerator, dose rate 22.41kGy/s, at room temperature in presence of air. After irradiation, some preliminary analyses were done like viscometry, texture analyses and colorimetry. The results of the diverse tests showed changes that can be ascribed to radiation-induced crosslinking. The electron-beam processed acrylamide-gelatin polymer using glycerin as plasticizer must be first extensively characterized before to be used for general applications. (author)

  8. Anaerobic digestion of residues from production and refining of vegetable oils as an alternative to conventional solutions.

    Science.gov (United States)

    Torrijos, M; Thalla, Arun Kumar; Sousbie, P; Bosque, F; Delgenès, J P

    2008-01-01

    The purpose of this work was to study the anaerobic digestion of by-products generated during the production and refining of oil with the objective of proposing an alternative solution (methanisation) to the conventional solutions while reducing the energy consumption of fossil origin on refinery sites. The production of sunflower oil was taken as example. Glycerine from the production of biodiesel was also included in this study. The results show that glycerine has a high potential for methanisation because of its high methane potential (465 ml CH4/g VS) and high metabolization rates (0.42 g VS/g VSS.d). The use of oil cake as substrate for anaerobic digestion is not interesting because it has a low methane potential of 215 ml CH4/g VS only and because it is easily recovered in animal feed. Six residues have quite a high methane potential (465 to 850 ml CH4/g VS) indicating a good potential for anaerobic digestion. However, they contain a mixture of rapidly and slowly biodegradable organic matter and the loading rates must remain quite low (0.03 to 0.09 g VS/g VSS.d) to prevent any accumulation of slowly biodegradable solids in the digesters. IWA Publishing 2008.

  9. Effect of coexisting organic substances on radiation resistance of Bacillus pumilus spores suspended in water

    International Nuclear Information System (INIS)

    Kigawa, Akiko; Tateishi, Tsuneo; Iso, Katsuaki; Kimura, Toshio; Mamuro, Tetsuo

    1987-01-01

    D values of B. pumilus spores suspended in water have been shown to increase in the presence of some coexisting organic substances. For elucidation of a mechanism or mechanisms involved in such a phenomenon, D-values of B.p. spores were examined by suspending them in aqueous solutions containing various concentrations of ethanol, glycerin, inulin and PVA. All these substances showed abrupt changes in D value at a narrow concentration range of 1 - 10 weight ppm. Solutions containing these substances at their lower limit concentrations and upper limit were prepared, sealed in incubator bottles leaving no air layer and irradiated at 0.7 Mrad with γ-rays. Winkler's method was used for the determination of oxygen concentrations in these solutions. The initial concentration of dissolved oxygen was 8.2 ppm. After irradiation, 3 - 5 ppm of oxygen remained in those solutions containing the lower limit (1 ppm), whereas only less than 0.5 ppm in those containing the upper limits, 2.5 ppm of ethanol, 5 ppm of PVA and 10 ppm each of glycerin and inulin. Therefore, the observed effect of coexisting organic substances on radiation resistance of B. pumilus can be explained by the so-called ''oxygen effect''. (author)

  10. Electron beam effects on gelatin polymer

    International Nuclear Information System (INIS)

    Inamura, Patricia Y.; Shimazaki, Kleber; Souza, Clecia de M.; Moura, Esperidiana A.B.; Mastro, Nelida L. del; Colombo, Maria A.

    2009-01-01

    The main field of electron-beam radiation processing applications is the modification of polymeric material. Polymer development includes new pathways to produce natural polymers with better mechanical and barrier properties and thermal stability. The aim of this paper was to investigate the behavior of a gelatin/acrylamide polymer treated by electron-beam radiation. Gelatin is a heterogeneous mixture of water-soluble proteins of high average molecular mass derived by hydrolytic action from animal collagen, a fibrous insoluble protein, which is widely found in nature as the major constituent of skin, bones and connective tissue. Hydrolyzed collagen is composed of a unique sequence of amino acids, characterized particularly by the high content of glycine, proline and hydroxyproline. Among biomaterials, gelatin is an interesting material because is a partially crystalline polymer and has a relatively low melting point. Samples of gelatin together with glycerin as plasticizer and acrylamide as copolymer were irradiated with doses of 10 kGy and 40 kGy, using an electron beam accelerator, dose rate 22.41kGy/s, at room temperature in presence of air. After irradiation, some preliminary analyses were done like viscometry, texture analyses and colorimetry. The results of the diverse tests showed changes that can be ascribed to radiation-induced crosslinking. The electron-beam processed acrylamide-gelatin polymer using glycerin as plasticizer must be first extensively characterized before to be used for general applications. (author)

  11. Necessity of glycolysis for recovery from ultraviolet killing of Saccharomyces cerevisiae

    International Nuclear Information System (INIS)

    Atsuta, J.; Okajima, S.

    1976-01-01

    An inverse relationship was found between uv (2537 A) survival and preirradiation respiratory rate of diploid yeast: Survival was consistently high in cells grown in anaerobic complete medium where only glycolysis was operating, while it was low in cells grown in aerobic glycerin medium where only oxidative phosphorylation was operating; these observations are consistent with the observed shift from the high resistance in logarithmic phase to the lesser resistance in stationary phase in cells grown in aerobic complete medium. Immediate recovery, which was determined by the ratio between split-dose survival and no recovery survival, occurred only in cells having a low respiratory rate and not in cells having a high respiratory rate. Severe suppression of aerobic ATP synthesis during the first hour after irradiation was found only in cells having a high respiratory rate. Otherwise, delayed recovery, which was determined by immediate plating on glycerin medium, was not related to the respiratory rate. These results indicate a low resistance to uv of oxidative phosphorylation in mitochondria existing at the time of irradiation and a high resistance to uv of both glycolysis and oxidative phosphorylation in new mitochondria produced after irradiation. Survival therefore may be dependent on whether irradiated cells can recover from sublethal damage by utilizing ATP produced by glycolysis immediately after irradiation

  12. High-purity fatty acid methyl ester production from canola, soybean, palm, and yellow grease lipids by means of a membrane reactor

    International Nuclear Information System (INIS)

    Cao Peigang; Dube, Marc A.; Tremblay, Andre Y.

    2008-01-01

    High-purity fatty acid methyl ester (FAME) was produced from different lipids, such as soybean oil, canola oil, a hydrogenated palm oil/palm oil blend, yellow grease, and brown grease, combined with methanol using a continuous membrane reactor. The membrane reactor combines reaction and separation in a single unit, provides continuous mixing of raw materials, and maintains a high molar ratio of methanol to lipid in the reaction loop while maintaining two phases during the reaction. It was demonstrated that the membrane reactor can be operated using a very broad range of feedstocks at highly similar operating conditions to produce FAME. The total glycerine and free glycerine contents of the FAME produced were below the ASTM D6751 standard after a single reaction step. Under essentially the same reaction conditions, a conventional batch reaction was not able to achieve the same degree of FAME purity. The effect of the fatty acid composition of the lipid feedstocks on the FAME purity was also shown. It was demonstrated that, due to the fatty acid composition, FAME from virgin soybean oil and virgin canola oil was produced in the membrane reactor within ASTM specifications even without a water washing step

  13. Evaluation of different magnetic resonance imaging contrast materials to be used as dummy markers in image-guided brachytherapy for gynecologic malignancies

    Energy Technology Data Exchange (ETDEWEB)

    Sales, Camila Pessoa; Carvalho, Heloisa de Andrade; Rubo, Rodrigo Augusto; Stuart, Silvia Radwanski; Rodrigues, Laura Natal, E-mail: camyps@gmail.com [Universidade de Sao Paulo (InRad/HC/FM/USP), Sao Paulo, SP (Brazil). Faculdade de Medicina. Instituto de Radiologia; Taverna, Khallil Chaim; Pastorello, Bruno Fraccini [Universidade de Sao Paulo (FM/USP), Sao Paulo, SP (Brazil). Departamento de Radiologia e Oncologia. Lab. de Ressonancia Magnetica em Neurorradiologia; Borgonovi, Arthur Felipe [Royal Philips Electronics, Eindhoven (Netherlands)

    2016-05-15

    Objective: to identify a contrast material that could be used as a dummy marker for magnetic resonance imaging. Materials and methods: magnetic resonance images were acquired with six different catheter-filling materials - water, glucose 50%, saline, olive oil, glycerin, and copper sulfate (CuSO{sub 4}) water solution (2.08 g/L) - inserted into compatible computed tomography/magnetic resonance imaging ring applicators placed in a phantom made of gelatin and CuSO{sub 4}. The best contrast media were tested in four patients with the applicators in place. Results: in T2-weighted sequences, the best contrast was achieved with the CuSO{sub 4}-filled catheters, followed by saline- and glycerin-filled catheters, which presented poor visualization. In addition (also in T2-weighted sequences), CuSO{sub 4} presented better contrast when tested in the phantom than when tested in the patients, in which it provided some contrast but with poor identification of the first dwell position, mainly in the ring. Conclusion: we found CuSO{sub 4} to be the best solution for visualization of the applicator channels, mainly in T2-weighted images in vitro, although the materials tested presented low signal intensity in the images obtained in vivo, as well as poor precision in determining the first dwell position. (author)

  14. Electronic cigarette nicotine delivery can exceed that of combustible cigarettes: a preliminary report.

    Science.gov (United States)

    Ramôa, Carolina P; Hiler, Marzena M; Spindle, Tory R; Lopez, Alexa A; Karaoghlanian, Nareg; Lipato, Thokozeni; Breland, Alison B; Shihadeh, Alan; Eissenberg, Thomas

    2016-04-01

    Electronic cigarettes (ECIGs) aerosolise a liquid that usually contains propylene glycol and/or vegetable glycerine, flavourants and the dependence-producing drug, nicotine, in various concentrations. This laboratory study examined the relationship between liquid nicotine concentration and plasma nicotine concentration and puffing behaviour in experienced ECIG users. Sixteen ECIG-experienced participants used a 3.3-Volt ECIG battery attached to a 1.5-Ohm dual-coil 'cartomiser' loaded with 1 mL of a flavoured propylene glycol/vegetable glycerine liquid to complete four sessions, at least 2 days apart, that differed by nicotine concentration (0, 8, 18 or 36 mg/mL). In each session, participants completed two 10-puff ECIG-use bouts (30 s puff interval) separated by 60 min. Venous blood was sampled to determine plasma nicotine concentration. Puff duration, volume and average flow rate were measured. Immediately after bout 1, mean plasma nicotine concentration was 5.5 ng/mL (SD=7.7) for 0 mg/mL liquid, with significantly (pcombustible cigarette. The rationale for this higher level of nicotine delivery is uncertain. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  15. Study on Mixed Solvency Concept in Formulation Development of Aqueous Injection of Poorly Water Soluble Drug

    Directory of Open Access Journals (Sweden)

    Shailendra Singh Solanki

    2013-01-01

    Full Text Available In the present investigation, mixed-solvency approach has been applied for the enhancement of aqueous solubility of a poorly water- soluble drug, zaltoprofen (selected as a model drug, by making blends (keeping total concentrations 40% w/v, constant of selected water-soluble substances from among the hydrotropes (urea, sodium benzoate, sodium citrate, nicotinamide; water-soluble solids (PEG-4000, PEG-6000; and co-solvents (propylene glycol, glycerine, PEG-200, PEG-400, PEG-600. Aqueous solubility of drug in case of selected blends (12 blends ranged from 9.091 ± 0.011 mg/ml–43.055 ± 0.14 mg/ml (as compared to the solubility in distilled water 0.072 ± 0.012 mg/ml. The enhancement in the solubility of drug in a mixed solvent containing 10% sodium citrate, 5% sodium benzoate and 25 % S cosolvent (25% S cosolvent contains PEG200, PEG 400, PEG600, Glycerine and Propylene glycol was more than 600 fold. This proved a synergistic enhancement in solubility of a poorly water-soluble drug due to mixed cosolvent effect. Each solubilized product was characterized by ultraviolet and infrared techniques. Various properties of solution such as pH, viscosity, specific gravity and surface tension were studied. The developed formulation was studied for physical and chemical stability. This mixed solvency shall prove definitely a boon for pharmaceutical industries for the development of dosage form of poorly water soluble drugs.

  16. Biodiesel Production from Microalgae by Extraction – Transesterification Method

    Directory of Open Access Journals (Sweden)

    Nguyen Thi Phuong Thao

    2013-11-01

    Full Text Available The environmental impact of using petroleum fuels has led to a quest to find a suitable alternative fuel source. In this study, microalgae were explored as a highly potential feedstock to produce biodiesel fuel. Firstly, algal oil is extracted from algal biomass by using organic solvents (n–hexan.  Lipid is contained in microalgae up to 60% of their weight. Then, Biodiesel is created through a chemical reaction known as transesterification between algal oil and alcohol (methanol with strong acid (such as H2SO4 as the catalyst. The extraction – transesterification method resulted in a high biodiesel yield (10 % of algal biomass and high FAMEs content (5.2 % of algal biomass. Biodiesel production from microalgae was studied through experimental investigation of transesterification conditions such as reaction time, methanol to oil ration and catalyst dosage which are deemed to have main impact on reaction conversion efficiency. All the parameters which were characterized for purified biodiesel such as free glycerin, total glycerin, flash point, sulfur content were analyzed according to ASTM standardDoi: http://dx.doi.org/10.12777/wastech.1.1.6-9Citation:  Thao, N.T.P., Tin, N.T., and Thanh, B.X. 2013. Biodiesel Production from Microalgae by Extraction – Transesterification Method. Waste Technology 1(1:6-9. Doi: http://dx.doi.org/10.12777/wastech.1.1.6-9

  17. [Diagnosis and treatment of pediatric anismus].

    Science.gov (United States)

    Ding, Shu-qing; Ding, Yi-jiang; Chen, Yong-tian; Ye, Hui

    2006-11-01

    To explore the diagnosis and treatment methods of pediatric anismus. Twenty-nine patients with idiopathic chronic constipation, diagnosed with anismus by colon barium contrast and anorectal manometry from Nov. 2001 to Nov. 2004 in our hospital, were investigated retrospectively. This group consisted of 13 men and 16 women whose mean age was (6.7+/-4.0) years. Hirschsprung diseases were excluded from the patients by colon barium contrast and rectoanal inhibitory reflex (RAIR) examination. Normal RAIR (5-10 ml elicited) was showed on 21 cases while weakened RAIR (15-30 ml elicited) was showed on 8 cases. After the diagnosis, the patients were treated by toilet training, diet regulation and laxative for 1-2 months. 4 cases were recovered, 5 cases were improved and 20 cases were relied on glycerin suppository. Four cases, relied on glycerin suppository, underwent Lynn procedure and had good results after 5-24 months follow-up. Two cases were re-examined by anorectal manometry 3 and 6 months after surgery, the resting pressure and the high pressure zone (HPZ) decreased, but the simulation defecation reflex was still abnormal. The diagnosis of pediatric anismus relies on history of constipation, combined with anorectal manometry and colon barium contrast. Lynn procedure could be chosen for the patients unsatisfied in toilet training and other non-operative treatment.

  18. Effect of Alcohols on the Phase Behavior and Emulsification of a Sucrose Fatty Acid Ester/Water/Edible Oil System.

    Science.gov (United States)

    Matsuura, Tsutashi; Ogawa, Akihiro; Ohara, Yukari; Nishina, Shogo; Nakanishi, Maho; Gohtani, Shoichi

    2018-02-01

    The effect of alcohols (ethanol, 1-propanol, propylene glycol, glycerin, sucrose) on the phase behavior and emulsification of sucrose stearic acid ester (SSE)/water/edible vegetable oil (EVO) systems was investigated. Adding sucrose, propylene glycol, and glycerin narrowed the oil-separated two-phase region in the phase diagram of the SSE/water/EVO systems, whereas adding ethanol and 1-propanol expanded the oil-separated two-phase region. Changing the course of emulsification in the phase diagram showed that the size of the oil-droplet particle typically decreased in a system with a narrowed oil-separated region. The emulsification properties of the systems varied with respect to changes in the phase diagram. The microstructure of the systems was examined using small-angle X-ray scattering, and the ability to retain the oil in the lamellar structure of the SSEs was suggested as an important role in emulsification, because the mechanism of the systems was the same as that for the liquid crystal emulsification method.

  19. Optimization of calcium phosphate fine ceramic powders preparation

    Science.gov (United States)

    Sezanova, K.; Tepavitcharova, S.; Rabadjieva, D.; Gergulova, R.; Ilieva, R.

    2013-12-01

    The effect of biomimetic synthesis method, reaction medium and further precursor treatments on the chemical and phase composition, crystal size and morphology of calcium phosphates was examined. Nanosized calcium phosphate precursors were biomimetically precipitated by the method of continuous precipitation in three types of reaction media at pH 8: (i) SBF as an inorganic electrolyte system; (ii) organic (glycerine) modified SBF (volume ratio of 1:1); (iii) polymer (10 g/l xanthan gum or 10 g/l guar gum) modified SBF (volume ratio of 1:1). After maturation (24 h) the samples were lyophilized, calcinated at 300°C for 3 hours, and washed with water, followed by new gelation, lyophilization and step-wise (200, 400, 600, 800, and 1000°C, each for 3 hours) sintering. The reaction medium influenced the chemical composition and particle size but not the morphology of the calcium phosphate powders. In all studied cases bi-phase calcium phosphate fine powders with well-shaped spherical grains, consisting of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA) with a Ca/P ratio of 1.3 - 1.6 were obtained. The SBF modifiers decreased the particle size of the product in the sequence guar gum ˜ xanthan gum < glycerin < SBF medium.

  20. FORMULATION OF AEROSOL CONCENTRATES CONTAINING HARUAN (Channa striatus FOR WOUND DRESSING

    Directory of Open Access Journals (Sweden)

    FEBRIYENTI

    2008-01-01

    Full Text Available The objective of this research was to formulate an aerosol concentrate containing haruan (Channa striatus water extract that would produce a thin film when sprayed onto a wound and could be used for wound dressing. The aerosol concentrates were formulated with various polymer and plasticiser mixtures and tested in dispersion systems. The polymers evaluated were hydroxypropyl methylcellulose (HPMC, carboxymethylcellulose sodium (CMC Sodium, acacia, tragacanth, chitosan, gelatine and gelatine (bloom 151–160, all at concentrations of 2%. The plasticisers evaluated were polyethylene glycol (PEG 400 and 4000, glycerine, propylene glycol, and triacetin. Films were prepared from film-forming dispersions by casting techniques. Film-forming dispersions were characterised in terms of pH, density, surface tension, rheological properties, particle size distribution, and tackiness. Based on these evaluations, HPMC was chosen as the best polymer. It produced a film with the expected qualities and was easy to reproduce in the form of dispersions or as thin transparent films. Glycerine was judged as the most appropriate plasticiser because it produced the concentrate having the desired qualities and properties expected from an aerosol concentrate

  1. Study of the conditions of activation and stabilization of Shigella sonnei 47 DNA methylases in the process of fractionation, purification, and during storage

    International Nuclear Information System (INIS)

    Suchkov, S.V.; Lopatina, N.G.; Arutyunyan, E.E.; Nikol'skaya, I.I.; Debov, S.S.

    1987-01-01

    A comparative investigation was made of the factors of activation and conditions of stabilization of partially purified and individual fractions of DNA methylases of the strain Shigella sonnei 47. The influence of the temperature system, glycerin, albumin, protease inhibitors, divalent metal ions, as well as the conditions of storage at the value of the isoelectric point of the protein on the activity of the enzymes of methylation was studied. It was shown that the effects of activating factors and levels of stabilization differ appreciably, depending on the degree of purification and the composition of the enzyme preparations. It was established that glycerin is ineffective as a stabilizing agent. It was shown that of all the divalent cations studied the only activator universal for the methylases of Shigella sonnei 47 is Ca 2+ ions. A pronounced stabilizing effect of albumin on the activity of these DNA methylases was demonstrated. With the exception of one enzymatic fraction, the protease inhibitors have virtually no effect on the level of methylating activity of the preparations. The phenomenon of spontaneous fluctuations of the methylating activity of Shigella sonnei 47 enzyme preparations during storage is described

  2. Experimental investigation of convective stability in a superposed fluid and porous layer when heated from below

    Science.gov (United States)

    Chen, Falin; Chen, C. F.

    1989-01-01

    Experiments have been carried out in a horizontal superposed fluid and porous layer contained in a test box 24 cm x 12 cm x 4 cm high. The porous layer consisted of 3 mm diameter glass beads, and the fluids used were water, 60 and 90 percent glycerin-water solutions, and 100 percent glycerin. The depth ratio d, which is the ratio of the thickness of the fluid layer to that of the porous layer, varied from 0 to 1.0. Fluids of increasingly higher viscosity were used for cases with larger d in order to keep the temperature difference across the tank within reasonable limits. The size of the convection cells was inferred from temperature measurements made with embedded thermocouples and from temperature distributions at the top of the layer by use of liquid crystal film. The experimental results showed: (1) a precipitous decrease in the critical Rayleigh number as the depth of the fluid layer was increased from zero, and (2) an eightfold decrease in the critical wavelength between d = 0.1 and 0.2. Both of these results were predicted by the linear stability theory reported earlier (Chen and Chen, 1988).

  3. Comparison of Select Analytes in Exhaled Aerosol from E-Cigarettes with Exhaled Smoke from a Conventional Cigarette and Exhaled Breaths

    Directory of Open Access Journals (Sweden)

    Gerald A. Long

    2014-10-01

    Full Text Available Exhaled aerosols were collected following the use of two leading U.S. commercial electronic cigarettes (e-cigarettes and a conventional cigarette by human subjects and analyzed for phenolics, carbonyls, water, glycerin and nicotine using a vacuum-assisted filter pad capture system. Exhaled breath blanks were determined for each subject prior to each product use and aerosol collection session. Distribution and mass balance of exhaled e-cigarette aerosol composition was greater than 99.9% water and glycerin, and a small amount (<0.06% of nicotine. Total phenolic content in exhaled e-cigarette aerosol was not distinguishable from exhaled breath blanks, while total phenolics in exhaled cigarette smoke were significantly greater than in exhaled e-cigarette aerosol and exhaled breaths, averaging 66 µg/session (range 36 to 117 µg/session. The total carbonyls in exhaled e-cigarette aerosols were also not distinguishable from exhaled breaths or room air blanks. Total carbonyls in exhaled cigarette smoke was significantly greater than in exhaled e-cigarette aerosols, exhaled breath and room air blanks, averaging 242 µg/session (range 136 to 352 µg/session. These results indicate that exhaled e-cigarette aerosol does not increase bystander exposure for phenolics and carbonyls above the levels observed in exhaled breaths of air.

  4. Accuracy analysis of the thermal diffusivity measurement of molten salts by stepwise heating method

    International Nuclear Information System (INIS)

    Kato, Yoshio; Furukawa, Kazuo

    1976-11-01

    The stepwise heating method for measuring thermal diffusivity of molten salts is based on the electrical heating of a thin metal plate as a plane heat source in the molten salt. In this method, the following estimations on error are of importance: (1) thickness effect of the metal plate, (2) effective length between the plate and a temperature measuring point and (3) effect of the noise on the temperature rise signal. In this report, a measuring apparatus is proposed and measuring conditions are suggested on the basis of error estimations. The measurements for distilled water and glycerine were made first to test the performance; the results agreed well with standard values. The thermal diffusivities of molten NaNO 3 at 320-380 0 C and of molten Li 2 BeF 4 at 470-700 0 C were measured. (auth.)

  5. The clinical impact of vehicle technology using a patented formulation of benzoyl peroxide 5%/clindamycin 1% gel: comparative assessments of skin tolerability and evaluation of combination use with a topical retinoid.

    Science.gov (United States)

    Del Rosso, James Q; Tanghetti, Emil

    2006-02-01

    A major challenge encountered in clinical practice in patients with acne vulgaris is irritation related to topical medications used for treatment. Advances in vehicle technology have improved formulations containing active ingredients known to produce irritation in some patients, such as benzoyl peroxide (BP) and topical retinoids. Clinical studies, including combination therapy studies have demonstrated that certain additives, such as silicates and specific humectants, reduce irritation by maintaining barrier integrity. A patented gel formulation of BP 5%/clindamycin phosphate 1% (clindamycin) containing dimethicone and glycerin has been studied both as a monotherapy and in combination with topical retinoid use. This article evaluates specific vehicle additives included in this gel formulation and explains their role in reducing irritation. Data from clinical trials utilizing this technology in acne management are also reviewed.

  6. Computed tomography to evaluate the association of fragmented heterolog cortical bone and methylmethacrylate to repare segmental bone defect produced in tibia of rabbits; Tomografia computadorizada da matriz ossea mineralizada heterologa fragmentada e metilmetacrilato na reparacao de falhas osseas segmentares produzidas em tibia de coelhos

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, S.H. [Universidade Federal de Sao Paulo (USP), SP (Brazil); Doria, R.G.S. [Universidade Federal de Sao Paulo (USP), SP (Brazil). Faculdade de Zootecnia e Engenharia de Alimentos; Mendonca, F.S.; Santos, M.D.; Moreira, R. [Universidade de Cuiaba, MT (Brazil). Faculdade de Medicina Veterinaria; Simoes, R.S. [Universidade Federal de Sao Paulo (USP), SP (Brazil). Hospital Universitario; Camargo, L.M.; Simoes, M.J. [Universidade Federal de Sao Paulo (USP), SP (Brazil). Escola Paulista de Medicina; Marques, A.T.C. [Universidade de Cuiaba, MT (Brazil). Faculdade de Odontologia

    2012-11-15

    A 6mm segmental defect was performed on the metaphyseal region of the tibia of 12 rabbits and the autoclaved fragmented heterolog cortical bone conserved in glycerin (98%) and methylmethacrylate was used as a bone graft for the reconstruction. The graft was placed in the receptor bed and its integration was evaluated by computed tomography after 30, 60 and 90 days. There was gradual bone graft incorporation in the receptor bed during the time in 100% of the cases. Fragmented cortical bone heterograft and methylmethacrylate was biologically compatible and promotes bone defect reparation without signs of infection, migration and or rejection, featuring a new option of osseous substitute to fill in bone defects. (author)

  7. Nanosecond pulsed power generator for a voltage amplitude up to 300 kV and a repetition rate up to 16 Hz for fine disintegration of quartz

    Energy Technology Data Exchange (ETDEWEB)

    Krastelev, E. G., E-mail: ekrastelev@yandex.ru; Sedin, A. A.; Tugushev, V. I. [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation)

    2015-12-15

    A generator of high-power high-voltage nanosecond pulses is intended for electrical discharge disintegration of mineral quartz and other nonconducting minerals. It includes a 320 kV Marx pulsed voltage generator, a high-voltage glycerin-insulated coaxial peaking capacitor, and an output gas spark switch followed by a load, an electric discharge disintegration chamber. The main parameters of the generator are as follows: a voltage pulse amplitude of up to 300 kV, an output impedance of ≈10 Ω, a discharge current amplitude of up to 25 kA for a half-period of 80–90 ns, and a pulse repetition rate of up to 16 Hz.

  8. Nanosecond pulsed power generator for a voltage amplitude up to 300 kV and a repetition rate up to 16 Hz for fine disintegration of quartz

    International Nuclear Information System (INIS)

    Krastelev, E. G.; Sedin, A. A.; Tugushev, V. I.

    2015-01-01

    A generator of high-power high-voltage nanosecond pulses is intended for electrical discharge disintegration of mineral quartz and other nonconducting minerals. It includes a 320 kV Marx pulsed voltage generator, a high-voltage glycerin-insulated coaxial peaking capacitor, and an output gas spark switch followed by a load, an electric discharge disintegration chamber. The main parameters of the generator are as follows: a voltage pulse amplitude of up to 300 kV, an output impedance of ≈10 Ω, a discharge current amplitude of up to 25 kA for a half-period of 80–90 ns, and a pulse repetition rate of up to 16 Hz

  9. Liquid--liquid surface impaction. Annual progress report, July 1, 1975--June 30, 1976

    International Nuclear Information System (INIS)

    Bankoff, S.G.

    1976-01-01

    The critical Weber number for coalescence, when a droplet of Freon-22 or pentane falls on a pool of hot (80-180 0 C) silicone oil or glycerine, has been determined as a function of pool temperature and droplet size. Using this information, a splash theory for local propagation of a vapor explosion has been formulated, which agrees with intermediate-scale peak pressure data of Henry, et al. A hydrodynamic theory has been constructed for the minimum thickness of the gas film in the approach phase. The Board-Hall theory for fuel-coolant detonation waves has been modified to take into account the presence of a swarm of drops, rather than a single drop. On this basis the existence of a steady-state Chapman-Jouguet wave in either the tin-water or UO 2 -sodium systems seems highly unlikely. Scoping experiments on Leidenfrost boiling of droplets and pool boiling from liquid metal surfaces have been initiated

  10. A study on the couplant effects in contact ultrasonic testing

    International Nuclear Information System (INIS)

    Lee, J. K.; Kim, H. C.; Lee, S. S.; Kim, Young H.

    1997-01-01

    The amplitude of the back-wall echoes depend on the reflection coefficient on the interface between transducer and test material in the contact pulse-echo ultrasonic testing. The couplant is used to transmit the ultrasonic energy through the interface, and has an influence on the amplitude of the pulse-echo signal. To investigate the couplant effect on the pulse-echo ultrasonic testing, the back-wall echoes are measured by using various couplants made of water and glycerine in a carbon and an austenitic stainless steel specimens. The amplitude of the first back-wall echo and the apparent attenuation coefficient increase with the acoustic impedance of couplant. The couplant having higher value of transmission coefficient is more effective for flaws detection, and the reflection coefficient should be known to measure the attenuation coefficient of test material.

  11. Comparative evaluation of retinoic acid, benzoyl peroxide and erythromycin lotion in acne vulgarils

    Directory of Open Access Journals (Sweden)

    Dogra A

    1993-01-01

    Full Text Available Ninety three patients suffering from acne vulgaris were treated with 0.05% retinoic acid (23 patients, 10% benzyoyl peroxide (24 patients, 2% erythromycin lotin (25 patients and 50% glycerine in methylated spirit (21 patients used as a control, for a period of 6 weeks. The patients were evaluated at 2 weeks and 6 weeks by spot counting of the lesions and diagrammatic representations. Good to excellent results were obtained in 69.6% of patients of erythromycin lotion. Retinoic acid was more effective in reducing noninflammatory lesions (75.2% whereas inflammatory lesions showed better response (73.6% with erythromycin lotion and benzoyl peroxide was almost equally effective in both types of lesions.

  12. Two new species of Tribonium Saussure, 1862 (Blattodea, Blaberidae, Zetoborinae), with a key to males of the genus.

    Science.gov (United States)

    da Silva, Leonardo de Oliveira Cardoso; Lopes, Sonia Maria

    2015-01-01

    This contribution describes and illustrates the male genitalia of two new species of Blaberidae collected in the state of Minas Gerais, Brazil: Triboniumcaldensis sp. n. resembles Triboniumneospectrum Lopes, 1978, differing in the coloration, size and genitalia; and Triboniummorroferrensis sp. n., which resembles Triboniumguttulosum (Walker, 1868) but also differs in the size and coloration of specimen and genital pieces morphology. The genital plates were removed after dissection of the posterior part of the abdomen, and were stored in microvials containing glycerin, attached to the respective exemplar in the collection of the Museu Nacional of Rio de Janeiro, Brazil. A key to males of the species of the genus is also presented. Illustrations of Triboniumneospectrum and Triboniumguttulosum are provided to clarify the comparisons with the new species described here.

  13. Radioimmunoassay of arginine vasopressin (AVP) and clinical application

    International Nuclear Information System (INIS)

    Wagner, H.; Haeberle, M.; Franz, H.E.; Maier, V.

    1977-01-01

    The low circulating levels of vasopressin required an initial extraction procedure. The extraction method itself presented problems with the specificity and the reproducibility of the extracted hormone from serum. The presented paper describes the developement of a radioimmunoassay without an extraction procedure. The AVP was coupled with rabbit-albumin by gluteraldehyde condensation for the immunization of rabbits. Synthetic AVP was iodinated by the method of GREENWOOD and HUNTER (1963) and purified by the addition of Dowex. The antibody cannot differentiate between lysine- and arginine-, ornithine-, glycerine - vasopressin and oxytocin. 1 - 24 ACTH and gastrin did not crosscreact. Normal subjects were found to have 5.7 +- 4.4/uU/ml after a dehydration period of 12 hours. Subjects suffering from psychogenic polydipsia showed normal levels, however, different forms of stress yielded higher levels in normal subjects. In patients suffering from liver cirrhosis the values normalized when ascites was under control. (orig.) [de

  14. The use of glycerol in PET chemical recycling with the prospect of the polymeric membranes production; Utilizacao de glicerol na reciclagem quimica de PET visando a producao de membranas polimericas cationicas

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Agne R. de; Consentino, Vinicius M.; Muniz, Aline S.; Sakae, George H.; Oliveira, Angelo R.S.; Cesar-Oliveira, Maria Aparecida F. [Universidade Federal do Parana - UFPR, Centro Politecnico, Curitiba, PR (Brazil)], e-mail: mafco@ufpr.br

    2011-07-01

    The recent interest in alternative sources of renewable energy of unlimited duration and with a low environmental impact, has led to a rise in the use and production of biodiesel. This requires an increase in the availability of glycerine in the market. This involves a study of new applications to increase the consumption of this raw material which can be linked to solving a serious environmental problem - the unsuitable disposal of post-consumption PET packages. Parallel to this, combustible cell technology is proving to have promising results, particularly in the area which uses polymeric electrolytes. The polymeric proton exchange membrane is currently most widely used in Nafion. However, this entails very high costs. By bringing together these important requirements in the energy sector, this study demonstrates how the development of aromatic sulfonate polyesters obtained from the chemical recycling of poly(ethylene terephthalate) with an aromatic derivative of glycerol. (author)

  15. [Wound Ballistics – a Brief Overview].

    Science.gov (United States)

    Bolliger, Stephan A; Eggert, Sebastian; Thali, Michael J

    2016-02-03

    Wound ballistics examines the specific effect, namely the wound profile, of bullets on the body by firing at synthetic models made of ordnance gelatine, glycerin soap and synthetic bones, validated with real cases from (battlefield) surgery and forensic pathology. Wound profile refers to the penetration depth, the bullet deformation/ fragmentation, the diameter of the permanent and the temporary wound cavity. Knowing these features and the used ammunition a surgeon can rapidly assess the amount damage within a patient. The forensic pathologist can draw conclusions as to the used ammunition based on the wound profile. By measuring of the destructive capability of different ammunition types, wound ballistics lays the foundation for guidelines concerning the maximum effect of military ammunition.

  16. Development of curcumin liposome formulations using polyol dilution method

    Directory of Open Access Journals (Sweden)

    Lalana Kongkaneramit

    2016-12-01

    Full Text Available This study was aimed to formulate curcumin liposomes (CLs by using polyol dilution method which is advantageous for no residue of organic solvent. CLs were the mixture of hydrogenated phosphatidylcholine (PC and cholesterol (CH at the molar ratio of 9:1. Propylene glycol (PG, glycerin, and polyethylene glycol 400 (PEG-400 were used as polyol solvent. Extrusion was applied after the suspension formed. The amount of polyol and curcumin and preparing temperature were investigated. The obtained suspensions were observed for appearance, size, size distribution, zeta potential, morphology, and percentage of entrapment. The results showed that type and amount of polyol had an impact on both liposomal size and the amount of entrapped curcumin, while preparing temperature was also an important factor. However, the solubility of lipids and drug in a given polyol should be considered because of loading efficiency in the formulation.

  17. Synthesis of PVA/PVP hydrogels having two-layer by radiation and their physical properties

    International Nuclear Information System (INIS)

    Park, K.R.; Nho, Y.C.

    2003-01-01

    In these studies, two-layer hydrogels which consisted of polyurethane membrane and a mixture of polyvinyl alcohol(PVA)/poly-N-vinylpyrrolidone(PVP)/glycerin/chitosan were made for the wound dressing. Polyurethane was dissolved in solvent, the polyurethane solution was poured on the mould, and then dried to make the thin membrane. Hydrophilic polymer solutions were poured on the polyurethane membranes, they were exposed to gamma irradiation or two steps of 'freezing and thawing' and gamma irradiation doses to make the hydrogels. The physical properties such as gelation, water absorptivity, and gel strength were examined to evaluate the hydrogels for wound dressing. The physical properties of hydrogels such as gelation and gel strength was greatly improved when polyurethane membrane was used as a covering layer of hydrogel, and the evaporation speed of water in hydrogel was reduced

  18. Ultrasonic-assisted chemical reduction synthesis and structural characterization of copper nanoparticles

    Science.gov (United States)

    Anh-Nga, Nguyen T.; Tuan-Anh, Nguyen; Thanh-Quoc, Nguyen; Ha, Do Tuong

    2018-04-01

    Copper nanoparticles, due to their special properties, small dimensions and low-cost preparation, have many potential applications such as in optical, electronics, catalysis, sensors, antibacterial agents. In this study, copper nanoparticles were synthesized by chemical reduction method with different conditions in order to investigate the optimum conditions which gave the smallest (particle diameter) dimensions. The synthesis step used copper (II) acetate salt as precursor, ascorbic acid as reducing agent, glycerin and polyvinylpyrrolidone (PVP) as protector and stabilizer. The assistance of ultrasonic was were considered as the significant factor affecting the size of the synthesized particles. The results showed that the copper nanoparticles have been successfully synthesized with the diameter as small as 20-40 nm and the conditions of ultrasonic waves were 48 kHz of frequency, 20 minutes of treated time and 65-70 °C of temperature. The synthesized copper nanoparticles were characterized by optical absorption spectrum, scanning electron microscopy (SEM), and Fourier Transform Infrared Spectrometry.

  19. A study on the repeatability of ultrasonic testing data

    International Nuclear Information System (INIS)

    Yoshimura, Seiichi; Fukumoto, Hiroshi

    1980-01-01

    Reliability improvement of ultrasonic testing data is strongly desired in ultrasonic testing working of nuclear power plants. This paper deals with the problems of the testing by the manual and the remote control apparatus, and with the factors which influence the repeatability of ultrasonic testing data. Following results are found in it. (1) In the testing by the manual, working time and posture influence the repeatability of testing data. (2) Glycerin in suitable for the couplant in the respect of the repeatability of testing data. In the case of using machine oil, the pressure to the probe necessitates to be over 0.2 kg/cm 2 . (3) In the testing by the remote control apparatus, working time, working environment and defect position does not influence the repeatability of testing data. (author)

  20. Can Heavier Liquid Float on Top of a Lighter One?

    International Nuclear Information System (INIS)

    Ayyad, A. H.; Takrori, F.

    2011-01-01

    We report on a first observation of a floating spherical Hg (density 13 g/cm 3 ) drop on top of a glycerin (density 1.26 g/cm 3 ) drop, the latter is hemispherical and about four times larger in volume. This observation is clearly against nature's gravity law and has never been reported before. Here we present spectacular high resolution photos that clearly demonstrate this remarkable floating phenomenon. Using milli-Q water, the Hg drop would stay down adhered at the triple line. Instead, the coincidental use of tap water displays the same phenomenon. Increasing the volume of the supporting liquid to a certain value causes the Hg drop to sink. A 5-M NaCl aqueous solution is found enough to show the same floating phenomenon. This floating mercury as a phenomenon is puzzling. On this length scale it seems that surface tension and curvature dominate over gravity. (fundamental areas of phenomenology (including applications))

  1. Le glycérol « building blocks » majeur de la bioraffinerie oléagineuse

    Directory of Open Access Journals (Sweden)

    Vandeputte Jacky

    2012-01-01

    Full Text Available Biodiesel production increases, and each ton of biodiésel produced leads to about 100 kg of glycerol. Because of increasing amount of generated glycerol, but also according to environmental concerns and scarcity of oil, glycerol is considered as one of the top 10 building block chemicals derived from biomass that can subsequently be converted into a number of high value biobased chemicals. Besides the well established sell of purified glycerine to manufacturers of cosmetics and pharmaceuticals, a variety of novel conversion techniques are introduced. This paper provides an overview of the latest biobased compounds produced from glycerol’s conversion, and of the lower environmental impact of these new ways of production.

  2. Postaccident heat removal. II. Heat transfer from an internally heated liquid to a melting solid

    International Nuclear Information System (INIS)

    Faw, R.E.; Baker, L. Jr.

    1976-01-01

    Microwave heating has been used in studies of heat transfer from a horizontal layer of internally heated liquid to a melting solid. Experiments were designed to simulate heat transfer and meltthrough processes of importance in the analysis of postaccident heat removal capabilities of nuclear reactors. Glycerin, heated by 2.45-GHz microwave radiation, was used to simulate molten fuel. Paraffin wax was used to simulate a melting barrier confining the fuel. Experimentally measured heat fluxes and melting rates were consistent with a model based on downward heat transfer by conduction through a stagnant liquid layer and upward heat transfer augmented by natural convection. Melting and displacement of the barrier material occurred by upward-moving droplets randomly distributed across the melting surface. Results indicated that the melting and displacement process had no effect on the heat transfer process

  3. Gonioscopy in primary angle closure glaucoma.

    Science.gov (United States)

    Bruno, Christina A; Alward, Wallace L M

    2002-06-01

    Primary angle closure is a condition characterized by obstruction to aqueous humor outflow by the peripheral iris, and results in changes in the iridocorneal angle that are visible through gonioscopic examination. Gonioscopy in these eyes, however, can be difficult. This chapter discusses techniques that might help in the examination. These include beginning the examination with the inferior angle, methods to help in looking over the iris, cycloplegia, locating the corneal wedge, indentation, van Herick estimation, examining the other eye, and topical glycerin. Finally, there is a discussion about the pathology associated with the closed angle, with emphasis on the appearance of iris bombé, plateau iris, and the distinction between iris processes and peripheral anterior synechiae.

  4. Surgical intrauterine insemination with cat semen cryopreserved with Orvus ES paste or sodium lauryl sulfate.

    Science.gov (United States)

    Tsutsui, Toshihiko; Mizutani, Tatsuji; Matsubara, Yuka; Toyonaga, Mari; Oba, Hiromichi; Hori, Tatsuya

    2011-02-01

    The mean post-thaw sperm motilities of feline frozen semen prepared with 1% OEP or 3 g/ml SLS as a cryoprotective agent, in addition to 7% glycerin, were 35.0 ± 2.4 and 37.0 ± 2.5%, respectively, showing no significant difference. On unilateral intrauterine insemination (UIUI) using these semen samples at a sperm number of 40 × 10(6), the conception rate was 70.0% (7/10) in the OEP group and 30% (3/10) in the SLS group, showing that the rate was higher in the OEP group, but the difference was not significant. It was suggested that sperm in frozen semen showing the above qualities were transferred to the contralateral uterine horn on UIUI.

  5. Preservation methods for isolates of ascochyta blight fungi

    Directory of Open Access Journals (Sweden)

    Joanna Marcinkowska

    2014-08-01

    Full Text Available Isolates of ascochyta blight fungi, two of Ascochyta pisi, four of Mycosphaerella pinodes and four of Phoma pinodella were stored: A - on slants under mineral oil, B - on CN's medium agar disks, and as conidial suspension: C - in glycerine, D · in water. Viability and pathogenicity of recovered cultures after each consecutive year were assesed from 1991 to 1999. The compared parameters were first of all strongly influenced by the preservation method, but fungus species and number of years had a minor importance. The best for longer storage was method "A" because after 9 years the isolates were viable, highly pathogenic, and cultures recovered from them were clean. Thc method "C'' is good for short keeping (2-3 years, as conidia in vials need only small space and gave clean cultures.

  6. Breeding of tryptophanase-producing Escherichia coli by use of N+ ion beam implantation

    International Nuclear Information System (INIS)

    Pang Min; Yao Jianming

    2009-01-01

    In this paper, the mutation breeding on Escherichia coli producing tryptophanase was studied after low energy N + ion beam implantation. Parameters in the N + ion beam implantation were firstly determined. It has been indicated that a high mutation rate of E.coli could be obtained by N + implantation with 10 keV and 13 x 10 14 N + /cm 2 when glycerin at 15 % concentration used as protector. After continuous mutagenicity a high-yield tryptophanase-producing strain has been screened out and both of its biomass and enzymatic activity are higher than the previous levels respectively. The results of scale-up production show that the biomass could be reach 8.2 g ww ·L -1 and 110 g L-tryptophan could be formed in the volume of 1L enzymatic reaction system. In addition, the characteristics of its stable descend ability and easy operation make it a promising strain for industrialization. (authors)

  7. Computed tomography to evaluate the association of fragmented heterolog cortical bone and methylmethacrylate to repare segmental bone defect produced in tibia of rabbits

    International Nuclear Information System (INIS)

    Freitas, S.H.; Doria, R.G.S.; Mendonca, F.S.; Santos, M.D.; Moreira, R.; Simoes, R.S.; Camargo, L.M.; Simoes, M.J.; Marques, A.T.C.

    2012-01-01

    A 6mm segmental defect was performed on the metaphyseal region of the tibia of 12 rabbits and the autoclaved fragmented heterolog cortical bone conserved in glycerin (98%) and methylmethacrylate was used as a bone graft for the reconstruction. The graft was placed in the receptor bed and its integration was evaluated by computed tomography after 30, 60 and 90 days. There was gradual bone graft incorporation in the receptor bed during the time in 100% of the cases. Fragmented cortical bone heterograft and methylmethacrylate was biologically compatible and promotes bone defect reparation without signs of infection, migration and or rejection, featuring a new option of osseous substitute to fill in bone defects. (author)

  8. Preparation of Grinding Aid Using Waste Acid Residue from Plasticizer Plant

    Science.gov (United States)

    Li, Lingxiao; Feng, Yanchao; Liu, Manchao; Zhao, Fengqing

    2017-09-01

    The grinding aid for granulated blast-furnace slag were prepared from waste acid residue from plasticizer plant through neutralization, de-methanol and granulation process. In this process, sulfuric acid was transformed into gypsum which has much contribution for grinding effect by combined use with the glycerol and poly glycerin in the waste. Fly ash was used for granulation for the composite grinding aid. Methanol can be recycled in the process. The result showed that the suitable addition of grinding aid is 0.03 % of granulated blast-furnace slag (mass). In this case, the specific surface area is 14% higher than that of the blank. Compared with the common grinding aids, it has excellent performance and low cost.

  9. Facile method for the synthesis of gold nanoparticles using an ion coater

    Science.gov (United States)

    Lee, Seung Han; Jung, Hyun Kyu; Kim, Tae Cheol; Kim, Chang Hee; Shin, Chang Hwan; Yoon, Tae-Sik; Hong, A.-Ra; Jang, Ho Seong; Kim, Dong Hun

    2018-03-01

    Herein we report a metal nanoparticle synthesis method based on a physical vapor deposition process instead of the conventional wet process of chemical reactions in liquids. A narrow size distribution of synthesized gold nanoparticles was obtained using an ion coater on glycerin at low vapor pressure. The nanoparticle size could be modulated by controlling the sputtering conditions especially the discharge current. Due to the formation of gold nanoparticles, a surface plasmon resonance peak appeared at ∼530 nm in the absorption spectrum. The surface plasmon resonance peak exhibited red-shift with increasing size of the gold nanoparticles. Our results provide a simple, environmental friendly method for the synthesis of metal nanoparticles by combine low-cost deposition apparatus and a liquid medium, which is free from toxic reagents.

  10. Correcting for color crosstalk and chromatic aberration in multicolor particle shadow velocimetry

    International Nuclear Information System (INIS)

    McPhail, M J; Fontaine, A A; Krane, M H; Goss, L; Crafton, J

    2015-01-01

    Color crosstalk and chromatic aberration can bias estimates of fluid velocity measured by color particle shadow velocimetry (CPSV), using multicolor illumination and a color camera. This article describes corrections to remove these bias errors, and their evaluation. Color crosstalk removal is demonstrated with linear unmixing. It is also shown that chromatic aberrations may be removed using either scale calibration, or by processing an image illuminated by all colors simultaneously. CPSV measurements of a fully developed turbulent pipe flow of glycerin were conducted. Corrected velocity statistics from these measurements were compared to both single-color PSV and LDV measurements and showed excellent agreement to fourth-order, to well into the viscous sublayer. Recommendations for practical assessment and correction of color aberration and color crosstalk are discussed. (paper)

  11. Porous core-shell carbon fibers derived from lignin and cellulose nanofibrils

    KAUST Repository

    Xu, Xuezhu

    2013-10-01

    This letter reports a method to produce lignin and cellulose nanofibrils (CNFs) based porous core-shell carbon fibers via co-electrospinning followed by controlled carbonization. Lignin formed the shell of the fiber while CNF network formed the porous core. Polyacrylonitrile (PAN) was added to the lignin solution to increase its electrospinability. CNFs were surface acetylated and dispersed in silicon oil to obtain a homogenous dispersion for electrospinning the porous core. Hollow lignin fibers were also electrospun using glycerin as the core material. FT-IR measurements confirmed the CNF acetylation. SEM micrographs showed the core-shell and hollow fiber nanostructures before and after carbonization. The novel carbon fibers synthesized in this study exhibited increased surface area and porosity that are promising for many advanced applications. © 2013 Elsevier B.V.

  12. Transesterification of rapeseed oil for biodiesel production in trickle-bed reactors packed with heterogeneous Ca/Al composite oxide-based alkaline catalyst.

    Science.gov (United States)

    Meng, Yong-Lu; Tian, Song-Jiang; Li, Shu-Fen; Wang, Bo-Yang; Zhang, Min-Hua

    2013-05-01

    A conventional trickle bed reactor and its modified type both packed with Ca/Al composite oxide-based alkaline catalysts were studied for biodiesel production by transesterification of rapeseed oil and methanol. The effects of the methanol usage and oil flow rate on the FAME yield were investigated under the normal pressure and methanol boiling state. The oil flow rate had a significant effect on the FAME yield for the both reactors. The modified trickle bed reactor kept over 94.5% FAME yield under 0.6 mL/min oil flow rate and 91 mL catalyst bed volume, showing a much higher conversion and operational stability than the conventional type. With the modified trickle bed reactor, both transesterification and methanol separation could be performed simultaneously, and glycerin and methyl esters were separated additionally by gravity separation. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Electropyroelectric technique for measurement of the thermal effusivity of liquids

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, R; Moreno, I; Araujo, C [Facultad de Fisica, Universidad Autonoma de Zacatecas, Calz. Solidaridad Esquina Paseo de la Bufa s/n, C. P. 98060, Zacatecas, Zac. (Mexico); Marin, E, E-mail: emarin63@yahoo.e, E-mail: emarinm@ipn.m [Centro de Investigacion en Ciencia Aplicada y TecnologIa Avanzada, Instituto Politecnico Nacional, LegarIa 694, Colonia Irrigacion, C. P. 11500, Mexico D. F. (Mexico)

    2010-06-09

    The photopyroelectric method has been recognized as a reliable and useful tool for the measurement of the thermal properties of condensed matter samples. Usually the photothermal signal is generated using intensity modulated light beams, whose amplitudes are difficult to maintain stable. In this paper we describe a variant of this technique that uses amplitude modulated electrical current as excitation source, via Joule heating of the metal contact on one side of the pyroelectric sensor. The possibilities of this method, called by us the electropyroelectric technique, for thermal effusivity measurements of liquid samples are shown using test samples of distilled water, ethanol and glycerine. The results obtained for this parameter agree well with the values reported in the literature. Our measurement uncertainties are about 3%, a fact that opens several possible applications.

  14. Electropyroelectric technique for measurement of the thermal effusivity of liquids

    International Nuclear Information System (INIS)

    Ivanov, R; Moreno, I; Araujo, C; Marin, E

    2010-01-01

    The photopyroelectric method has been recognized as a reliable and useful tool for the measurement of the thermal properties of condensed matter samples. Usually the photothermal signal is generated using intensity modulated light beams, whose amplitudes are difficult to maintain stable. In this paper we describe a variant of this technique that uses amplitude modulated electrical current as excitation source, via Joule heating of the metal contact on one side of the pyroelectric sensor. The possibilities of this method, called by us the electropyroelectric technique, for thermal effusivity measurements of liquid samples are shown using test samples of distilled water, ethanol and glycerine. The results obtained for this parameter agree well with the values reported in the literature. Our measurement uncertainties are about 3%, a fact that opens several possible applications.

  15. An experimental study about efficacy of the drain catheters

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Bum Gyu; Nho, Joon Young; Woo, Hyo Cheol; Hwang, Woo Cheol; Park, Choong Ki; Yoon, Jong Sup [Hallym University College of Medicine, Seoul (Korea, Republic of)

    1993-09-15

    Although percutaneous abscess drainage has become and accepted alternative from of therapy for selected patients with abscess, it is well known that there are several factors in the failure of adequate drainage such as pre- and post-procedural management, technique itself, various features of abscess, and selection and application of catheters. Among these factors, we made an experiment about drainage efficacy of commonly used various catheters with different viscosities of water-glycerin solution under the two different pressure gradients. The experimental values of flow rate were very lower than the calculated values. An efficacy of experimental value was 4-14%. Because the inner diameter of fittings and stopcocks was usually smaller than the inner diameter of catheters, these factors also affected the drain efficacy. Finally, we thought that it will be very helpful to the treatment of patient as well as to study about the catheter drainage, if the drain efficacy of individual catheters has been notified.

  16. Modeling principles applied to the simulation of a joule-heated glass melter

    International Nuclear Information System (INIS)

    Routt, K.R.

    1980-05-01

    Three-dimensional conservation equations applicable to the operation of a joule-heated glass melter were rigorously examined and used to develop scaling relationships for modeling purposes. By rigorous application of the conservation equations governing transfer of mass, momentum, energy, and electrical charge in three-dimensional cylindrical coordinates, scaling relationships were derived between a glass melter and a physical model for the following independent and dependent variables: geometrical size (scale), velocity, temperature, pressure, mass input rate, energy input rate, voltage, electrode current, electrode current flux, total power, and electrical resistance. The scaling relationships were then applied to the design and construction of a physical model of the semiworks glass melter for the Defense Waste Processing Facility. The design and construction of such a model using glycerine plus LiCl as a model fluid in a one-half-scale Plexiglas tank is described

  17. Activity and structure of calcined coal gangue

    Energy Technology Data Exchange (ETDEWEB)

    Gong Chenchen; Li Dongxu; Wang Xiaojun; Li Zongjin [Nanjing University of Technology, Nanjing (China). College of Materials Science and Engineering

    2007-12-15

    Coal gangue was activated by means of calcination in seven temperature ranges. Systematic research was made about activation mechanism and structural evolution. The glycerin-ethanol method, SEM, MIP and XRD were used to determine the variation of structure and activation of coal gangue during calcination. The experimental results show that because of heat treatment in the range of calcination temperatures, mineral composition and microstructure of coal gangue are changed. In addition, its activity is improved. The amount of lime absorbed by the sample calcined at 700{sup o}C is 2-4 times that by uncalcined coal gangue in the course of hydration. When NaOH is added to coal gangue-lime system, the hydration reaction rate of the system is increased and the microstructure of hydrating samples of coal gangue is improved.

  18. The Effect Of Temperature On The Development Of Adult Generations Of Entomopathogenic Nematode Steinernema Arenarium Isolate CH

    Directory of Open Access Journals (Sweden)

    Yakovlev Ye. B.

    2015-08-01

    Full Text Available Steinernema arenarium isolate CH was prepared at 22 °C and used as a control in laboratory experiments on rearing in Galleria mellonella larvae at different temperatures (18 and 28 °C. Host dead bodies were examined every two days. All reared adult nematodes were fixed in alcohol and mounted on permanent slides with glycerin solution in distilled water. The basic morphometric parameters (L, W, ES, ABD (CBD, T, V were measured, and statistical analysis was performed. Morphometric data in males and females of both generations were shown to significantly change depending on speed of growth and nutrients concentration. In both experimental groups, pygmy forms of adults were found.

  19. Leptopsylla algira costai (Siphonaptera: Leptopsyllidae: New host and new geographical record

    Directory of Open Access Journals (Sweden)

    Ali Yousefi

    2016-11-01

    Full Text Available Objective: To access the emerging ectoparasites associated with shrews in Hamedan Province of Iran. Methods: We have captured bicoloured white-toothed shrews [Crocidura leucodon (C. leucodon] using the live traps in April 2014. Ectoparasites collected by brushing the skins were removed and preserved in 70% ethanol containing 5% glycerin, and subsequently they were sent to the parasitology laboratory and processed. The fleas isolated from infested specimen were cleared in 10% aqueous potassium hydroxide, dehydrated in ethanol, cleared in xylene, mounted in Canada balsam and identified using reliable keys. Results: In general, eight fleas (one male, seven females were collected from C. leucodon in Hamedan Province, Western Iran. The fleas were identified as Leptopsylla algira costai Smit, 1955. Conclusions: Fleas are medically important because they transmit a wide variety of diseases to their hosts. In addition, this aricle reports Leptopsylla algira costai for the first time in new host (C. leucodon and new geographical region (Iran.

  20. Palynomorphs in Holocene sediments from a paleolagoon in the coastal plain of extreme southern Brazil

    Directory of Open Access Journals (Sweden)

    Ebráilon Masetto

    2014-06-01

    Full Text Available This paper presents the results of a qualitative palynological analysis of a 140 cm-thick section of Holocene sediments from a paleolagoon, representing the last 2600 years, taken from an outcrop at Hermenegildo Beach (33º42'S; 53º18'W, located in the municipality of Santa Vitória do Palmar, in the state of Rio Grande do Sul, Brazil. Samples were treated with hydrochloric acid, hydrofluoric acid and potassium hydroxide, after which they were subjected to acetolysis and mounted on glycerin-coated slides for light microscopy analysis. Among the 48 palynomorphs identified were 25 fungi, eight algae, three bryophytes, and 12 pteridophytes. Brief descriptions and illustrations of each palynomorph are presented, together with ecological data from the organism of origin when possible. Our findings will serve as reference material for paleoenvironmental studies in the coastal plain of southern Brazil.

  1. Synthesis and Characterization of Solution and Melt Processible Poly(Acrylonitrile-Co-Methyl Acrylate) Statistical Copolymers

    Science.gov (United States)

    Pisipati, Padmapriya

    (acrylonitrile-co-methyl acrylate) of Mw = 200 kg/mol to 160 0C as measured via DSC. Glycerin, ethylene glycol and glycerin/water combinations were investigated as potential plasticizers for high molecular weight (˜200,000 g/mol), high acrylonitrile (93-96 mole:mole %) content poly(acrylonitrile-co-methyl acrylate) statistical copolymers. Pure glycerin (25 wt %) induced crystallization followed by a reduced "Tm" of about 213 0C via DSC. However this composition did not melt process well. A lower M W (˜35 kg/mol) copolymer did extrude with no apparent degradation. Our hypothesis is that the hydroxyl groups in glycerin (or water) disrupt the strong dipole-dipole interactions between the chains enabling the copolymer endothermic transition (Tm) to be reduced and enable melting before the onset of degradation. Additionally high molecular weight (Mw = 200-230 kg/mol) poly(acrylonitrile-co-methyl acrylate) copolymers with lower acrylonitrile content (82-85 wt %) were synthesized via emulsion copolymerization and successfully melt pressed. These materials will be further investigated for their utility in packaging applications.

  2. Protective Coatings

    Science.gov (United States)

    1980-01-01

    General Magnaplate Corporation's pharmaceutical machine is used in the industry for high speed pressing of pills and capsules. Machine is automatic system for molding glycerine suppositories. These machines are typical of many types of drug production and packaging equipment whose metal parts are treated with space spinoff coatings that promote general machine efficiency and contribute to compliance with stringent federal sanitation codes for pharmaceutical manufacture. Collectively known as "synergistic" coatings, these dry lubricants are bonded to a variety of metals to form an extremely hard slippery surface with long lasting self lubrication. The coatings offer multiple advantages; they cannot chip, peel or be rubbed off. They protect machine parts from corrosion and wear longer, lowering maintenance cost and reduce undesired heat caused by power-robbing friction.

  3. Green LPG

    Energy Technology Data Exchange (ETDEWEB)

    Hulteberg, Christian; Brandin, Jan; Leveau, Andreas (Biofuel-Solution AB, Limhamn (Sweden))

    2010-12-15

    The use of energy gases with renewable origins will become important with diminishing fossil resources. This as the infrastructure of the gaseous fuels is well built out and the distribution networks already exist. LPG is one of the most versatile fuels around, perfect for rural areas and in many other applications. The fossil origin of the fuel will, in today's climate and environmental debate, however position it as a thing of the past and not part of the future energy supply. The technology and development performed under this and previous programs with the Swedish Gas Centre will however suggest a way to bridge this conception and make LPG a part of the future energy mix. This report constitutes the results from the development performed under the SGC program 210 and is aimed at verifying the results from the previous SGC program 198, proving the concept for producing propane from renewable glycerol. Attractive and potentially profitable LPG premium segments that can be reached by producing bio-propane would be the autogas market. Another attractive segment to target is the outdoor and camping segment, where there already exist awareness for nature and the environment. A third interesting segment is in small-scale heat or combined heat and power generation, where a premium price can be reaped for renewable energy as well as the addition of LPG to biogas. Another important aspect of the renewable LPG is that it motivates external stakeholders, such as local, regional, national and international governments as well as environmental and other lobby groups to consider LPG a part of the future energy mix and not a thing of the past. A good starting point for two and three carbon energy gases is glycerine, with its three carbon backbone. The reason for focusing on glycerine is its benign chemical nature, it is: - Harmless from a toxic standpoint; - Chemically inert; - Non-corrosive; - Relatively high energy density; - Zero carbon dioxide emissions. It is also

  4. Detection of environmental radioactive contamination levels using a liquid-scintillation counter

    International Nuclear Information System (INIS)

    Calisto, W.; Kun, A.; Campos, E.

    1981-01-01

    A high-efficiency LS-100 C liquid scintillation counter was used to detect low levels of environmental activity. Different concentrations of primary scintillator were tested and these established the most suitable values. Work was carried out at the same time to find conditions which would ensure a low background and high efficiency. To reduce the sample volume used, various types of chelating agents were utilized: 8-hydroxyquinoline (oxine), tannic acid, cupferron, dimethylglioxime and beta-naphthol. These were tested at pH levels of 1, 6 and 11. Measurements were performed by means of the Cerenkov effect using substances with differing refraction indices - 26% sodium chloride, water, glycerine, carbon bisulphide, nitrobenzene, benzyl alcohol and toluene. Finally, work was done on comparing spectra obtained by Cerenkov radiation and by 90 Sr and 90 Y beta radiation respectively. Clearly differentiated zones were obtained, thus making it possible to distinguish one isotope from another in an equilibrium solution. (author)

  5. Effect of electron beam irradiation on mechanical properties of gelatin/Brazil nut shell fiber composites

    International Nuclear Information System (INIS)

    Inamura, Patricia Y.; Shimazaki, Kleber; Moura, Esperidiana Augusta Barretos de; Mastro, Nelida L. del; Colombo, Maria Aparecida; Rosa, Ricardo de

    2010-01-01

    The use of natural fiber as polymeric matrix reinforcement has attracted interest, as fibers are renewable, of low cost, biodegradable and possesses non-toxic properties. In the present paper, Brazil nuts (Bertholletia excelsa) shell fiber (10% w/w) were mixed with gelatin (25% w/w), glycerin as plasticizer and acrylamide as copolymer to investigate the resultant mechanical properties effects upon ionizing radiation. The samples were irradiated at 40 kGy using a Dynamitron electron beam accelerator, at room temperature in the presence of air. The results showed that samples of gelatin with 10% of Brazil nuts shell fiber and irradiated at 40 kGy presented promising results for mechanical performance. (author)

  6. Preparation and characterization of polymer blends based on recycled PET and polyester derived by terephthalic acid

    International Nuclear Information System (INIS)

    Ohara, L.; Miranda, C.S.; Fiuza, R.P.; Luporini, S.; Carvalho, R.F.; Jose, N.M.

    2010-01-01

    Environmentally friendly materials, made from industrial waste, are being increasingly used as a solution to the growing amount of waste generated by society, but also as a cheaper alternative to replace conventional materials for use in construction. In this work were investigated the properties of polymer blends based on recycled PET and a polyester derived from terephthalic acid and glycerin, a co-product of biodiesel. The samples were characterized by XRD, TGA, DSC, FTIR and SEM. The polyester synthesized showed a degradation event near 300 deg C. The blends with higher ratio of PET showed thermal behavior similar to pure PET. The X-ray diffraction showed that the polymer blends are semicrystalline materials. The micrographs presents the presence of a smooth surface, indicating the possibility of miscibility between the arrays. Therefore, the blending makes possible the fabrication of low-cost materials with applications in several areas. (author)

  7. Chemical characterization of composites developed from glycerol and dicarboxylic acids rein forced with piassava fiber

    International Nuclear Information System (INIS)

    Miranda, Cleidiene S.; Oliveira, Jamerson C.; Guimaraes, Danilo H.; Jose, Nadia M.; Carvalho, Ricardo F.

    2011-01-01

    In search of alternative technologies that enable the use of products with lower environmental impact, This study aims to develop a composite polymer-based piassava fiber. The sludge, waste and byproduct of commercial uses currently being used as reinforcement in polymer matrices, due to presence of lignocellulosic materials. The matrix polymer used was synthesized from glycerol with dicarboxylic acids, in order to open future perspectives on the use of glycerin generated from purified biodiesel production plastics. Composites with 2, 5, 10 wt% of piassava fiber cut into 5 mm raw and treated were obtained a mixture of solution. The materials were characterized by TGA, DSC, XRD and SEM. It was observed that the material under study is promising for the industrial market, because it has good compatibility with natural fibers allowing wider application of fiber natural and glycerol, producing semicrystalline composites and with good thermal properties. (author)

  8. The 'diester partners' want to be movers...; Les ''partenaires diester'' se veulent moteur...

    Energy Technology Data Exchange (ETDEWEB)

    Tourneur, J.C.

    2003-09-01

    Diester is the French name given to the biofuel (methylic ester) made from vegetal oils (1 t of vegetal oil + 0.1 t of methanol leads to 1 t of diester + 0.1 t of glycerin). The French club of 'diester towns' gathers all local authorities of towns that use up to 30% of diester in the diesel fuel of their vehicle fleets (buses, trucks, commercial vehicles). In March 2003, the association has opened to new members, in particular private companies which are diester users and become 'diester partners', in order to sustain the fight against the greenhouse effect. The consumption of 1 t of diester allows to save 2.5 t of CO{sub 2} thanks to the photosynthesis. In other words, a vehicle fueled with 30% of diester and 70% of diesel fuel reduces its greenhouse gas emissions of 23%. (J.S.)

  9. Process development for scum to biodiesel conversion.

    Science.gov (United States)

    Bi, Chong-hao; Min, Min; Nie, Yong; Xie, Qing-long; Lu, Qian; Deng, Xiang-yuan; Anderson, Erik; Li, Dong; Chen, Paul; Ruan, Roger

    2015-06-01

    A novel process was developed for converting scum, a waste material from wastewater treatment facilities, to biodiesel. Scum is an oily waste that was skimmed from the surface of primary and secondary settling tanks in wastewater treatment plants. Currently scum is treated either by anaerobic digestion or landfilling which raised several environmental issues. The newly developed process used a six-step method to convert scum to biodiesel, a higher value product. A combination of acid washing and acid catalyzed esterification was developed to remove soap and impurities while converting free fatty acids to methyl esters. A glycerol washing was used to facilitate the separation of biodiesel and glycerin after base catalyzed transesterification. As a result, 70% of dried and filtered scum was converted to biodiesel which is equivalent to about 134,000 gallon biodiesel per year for the Saint Paul waste water treatment plant in Minnesota. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Spray nozzles, pressures, additives and stirring time on viability and pathogenicity of entomopathogenic nematodes (nematoda: rhabditida) for greenhouses.

    Science.gov (United States)

    Moreira, Grazielle Furtado; Batista, Elder Simões de Paula; Campos, Henrique Borges Neves; Lemos, Raphael Emilio; Ferreira, Marcelo da Costa

    2013-01-01

    The objective of this study was to evaluate different strategies for the application of entomopathogenic nematodes (EPN). Three different models of spray nozzles with air induction (AI 11003, TTI 11003 and AD-IA 11004), three spray pressures (207, 413 and 720 kPa), four different additives for tank mixtures (cane molasses, mineral oil, vegetable oil and glycerin) and the influence of tank mixture stirring time were all evaluated for their effect on EPN (Steinernema feltiae) viability and pathogenicity. The different nozzles, at pressures of up to 620 kPa, were found to be compatible with S. feltiae. Vegetable oil, mineral oil and molasses were found to be compatible adjuvants for S. feltiae, and stirring in a motorized backpack sprayer for 30 minutes did not impact the viability or pathogenicity of this nematode. Appropriate techniques for the application of nematodes with backpack sprayers are discussed.

  11. The early phyllosoma stages of spiny lobster Panulirus echinatus Smith, 1869 (Decapoda: Palinuridae reared in the laboratory

    Directory of Open Access Journals (Sweden)

    FA. Abrunhosa

    Full Text Available The early stages of the Panulirus echinatus were hatched and reared in the laboratory. Ovigerous females were captured in their habitat and carefully transported to the laboratory. Larvae were transferred in a recirculation water tank at a density of 10 larvae.L-1. The larvae were fed on Artemia and gonads of mussel Brachydonts sp. Microalgae Dunaliella viridis was added at a concentration of 150 x 10(4 cell.mL-1. Larvae and exuviae of each zoeal stage were preserved in an alcohol 70% + glycerin (1:1 solution. The phyllosomas moulted eight times; the intermoulting period of each instar averaged about 7 to 10 days. The main morphological changes of each appendage were described in detail, illustrated and compared with previous reports.

  12. The Effects of Viscous Dissipation on Convection in a Porus Medium

    Directory of Open Access Journals (Sweden)

    T Raja Rani

    2017-05-01

    Full Text Available The aim of this paper is to study of the effects of variable physical properties and viscous dissipation on a free convective flow over a vertical plate with a variable temperature embedded in a porous medium. We study the effects of varying physical properties on heat transfer and on flow when the medium is filled with some commonly used experimental fluids, in particular, Glycerin, Water and Methyl chloride (a commonly refrigerant. A similarity transformation technique is used to reduce the partial differential equations governing the flow. The resulting system of non-linear coupled ordinary differential equations is solved numerically with appropriate boundary conditions using the Runge-Kutta-Gill method coupled with a shooting technique. Using this approach, a study is conducted on both hot and cold plates and results presented using a combination of graphical illustrations and tables of the effect of changing a variety of physical parameters, in particular, the temperature and viscosity of the fluid.

  13. [Stimulation of wound healing by tetrachlordecaoxide. Results of a randomized double-blind study].

    Science.gov (United States)

    Hinz, J; Hautzinger, H; Helling, J; Schirren, G; Sell, G; Stahl, K W; Kühne, F W

    1984-05-10

    In 38 patients with chronic therapeutically resistant wounds, which, in 25 cases, had been existing for more than one year, Tetrachlorodecaoxide ( TCDO ) in a water solution containing glycerin was analyzed for its capacity to induce wound healing and compared in this respect to the standard in moist wound treatment, physiological sodium chloride. The results of the clinical trial demonstrate that the TCDO solution is significantly superior to physiological saline in local wound treatment regarding the degree of wound smear reduction, the formation of wound granulation tissue, the stimulation of epithelisation on the wound borders and the shrinking of the wound surface. The differences in therapeutic efficiency are so large that, in spite of the relatively small patient samples (21 + 17) it was possible to verify the superiority of a method for wound treatment in a randomized double blind clinical trial.

  14. High Infestation by Dawestrema cycloancistrioides in Arapaima gigas Cultured in the Amazon Region, Peru

    Directory of Open Access Journals (Sweden)

    Patrick D. Mathews

    2014-01-01

    Full Text Available The aim of this study was to evaluate the presence of Dawestrema cycloancistrioides in semi-intensive fish farming of fingerlings of Arapaima gigas. Between September and November 2013, 60 individuals of A. gigas born in captivity, were collected in three concrete ponds, from a semi-intensive fish farm in the Peruvian Amazon. For the study of sclerotized structures, parasites were fixed in a solution of ammonium picrate glycerine and mounted in Canada balsam. To visualize internal structures, parasites were fixed in hot formaldehyde solution (4% for staining with Gomori’s trichrome. The parasitic indexes calculated were prevalence, mean intensity, and mean abundance. This study identified a high infestation of a monogenean D. cycloancistrioides in gills of A. gigas. The prevalence was 100%. The mean intensity and mean abundance of the parasite were 144.9 of parasites per individual. This study confirms the necessity of constant monitoring of fish in order to reduce fish mortality.

  15. High Infestation by Dawestrema cycloancistrioides in Arapaima gigas Cultured in the Amazon Region, Peru.

    Science.gov (United States)

    Mathews, Patrick D; Malheiros, Antonio F; Vasquez, Narda D; Chavez, Milton D

    2014-01-01

    The aim of this study was to evaluate the presence of Dawestrema cycloancistrioides in semi-intensive fish farming of fingerlings of Arapaima gigas. Between September and November 2013, 60 individuals of A. gigas born in captivity, were collected in three concrete ponds, from a semi-intensive fish farm in the Peruvian Amazon. For the study of sclerotized structures, parasites were fixed in a solution of ammonium picrate glycerine and mounted in Canada balsam. To visualize internal structures, parasites were fixed in hot formaldehyde solution (4%) for staining with Gomori's trichrome. The parasitic indexes calculated were prevalence, mean intensity, and mean abundance. This study identified a high infestation of a monogenean D. cycloancistrioides in gills of A. gigas. The prevalence was 100%. The mean intensity and mean abundance of the parasite were 144.9 of parasites per individual. This study confirms the necessity of constant monitoring of fish in order to reduce fish mortality.

  16. Modeling a forced to natural convection boiling test with the program LOOP-W

    International Nuclear Information System (INIS)

    Carbajo, J.J.

    1984-01-01

    Extensive testing has been conducted in the Simulant Boiling Flow Visualization (SBFV) loop in which water is boiled in a vertical transparent tube by circulating hot glycerine in an annulus surrounding the tube. Tests ranged from nonboiling forced convection to oscillatory boiling natural convection. The program LOOP-W has been developed to analyze these tests. This program is a multi-leg, one-dimensional, two-phase equilibrium model with slip between the phases. In this study, a specific test, performed at low power where non-boiling forced convection was changed to boiling natural convection and then to non-boiling again, has been modeled with the program LOOP-W

  17. Characterization of Mg-containing hydroxyapatites synthesized by combustion method

    Science.gov (United States)

    Kaygili, Omer; Keser, Serhat; Bulut, Niyazi; Ates, Tankut

    2018-05-01

    In the present paper, Mg-substituted hydroxyapatites with the morphology, composed of the stacked plate- and rod-like structures, were prepared at the temperature of 600 °C by combustion method using glycerine as a fuel. A significant decrease in the crystallite size values calculated for both Scherrer and Williamson-Hall methods is found. The crystallinity, lattice parameter of a, stress and anisotropic energy density values decreased by adding of Mg, whereas the lattice strain increased. The amount of HAp phase decreases with increasing amount of Mg and the β-tricalcium phosphate content increases. Mg incorporation the apatitic structure was detected. Depending on the increase in Mg content, Ca-deficiency was observed.

  18. Protein gradient films of fibroin and gelatine.

    Science.gov (United States)

    Claussen, Kai U; Lintz, Eileen S; Giesa, Reiner; Schmidt, Hans-Werner; Scheibel, Thomas

    2013-10-01

    Gradients are a natural design principle in biological systems that are used to diminish stress concentration where materials of differing mechanical properties connect. An interesting example of a natural gradient material is byssus, which anchors mussels to rocks and other hard substrata. Building upon previous work with synthetic polymers and inspired by byssal threads, protein gradient films are cast using glycerine-plasticized gelatine and fibroin exhibiting a highly reproducible and smooth mechanical gradient, which encompasses a large range of modulus from 160 to 550 MPa. The reproducible production of biocompatible gradient films represents a first step towards medical applications. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Chalk effect on PVC cross-linking under irradiation

    International Nuclear Information System (INIS)

    Chudinova, V.V.; Guzeev, V.V.; Mozzhukhin, V.B.; Pomerantseva, Eh.G.; Nozrina, F.D.; Zhil'tsov, V.V.; Zubov, V.P.

    1994-01-01

    Effect of nonmodified and modified chalk on curing degree of polymer matrix was studied under-irradiation of PVC-compositions. Films of the compositions (100 mass part 7 PVC, 0-100 mas.part of chalk, 2.5 - lead sulfate, 1.5 - lead stearate and 0.3 - glycerin) were irradiated up to absorbed dose 0.1 MGy in an inert medium. Content of gel-fraction after boiling in THF was determined with use of IR spectroscopy. It was established, that intensive dehydrochlorination and polymer curing took place on chalk particle surface. Network fixed strongly chalk particles. However, chalk inhibited processes of dehydrochlorination and PVC curing, increasing amount of noncured PVC in polymer matrix

  20. Chalk effect on PVC cross-linking under irradiation; Vliyanie mela na sshivanie PVKh pri obluchenii

    Energy Technology Data Exchange (ETDEWEB)

    Chudinova, V V; Guzeev, V V; Mozzhukhin, V B; Pomerantseva, Eh G; Nozrina, F D; Zhil` tsov, V V; Zubov, V P

    1994-12-31

    Effect of nonmodified and modified chalk on curing degree of polymer matrix was studied under-irradiation of PVC-compositions. Films of the compositions (100 mass part 7 PVC, 0-100 mas.part of chalk, 2.5 - lead sulfate, 1.5 - lead stearate and 0.3 - glycerin) were irradiated up to absorbed dose 0.1 MGy in an inert medium. Content of gel-fraction after boiling in THF was determined with use of IR spectroscopy. It was established, that intensive dehydrochlorination and polymer curing took place on chalk particle surface. Network fixed strongly chalk particles. However, chalk inhibited processes of dehydrochlorination and PVC curing, increasing amount of noncured PVC in polymer matrix.

  1. Effect of Temperature Change on Geometric Structure of Isolated Mixing Regions in Stirred Vessel

    Directory of Open Access Journals (Sweden)

    Nor Hanizah Shahirudin

    2012-01-01

    Full Text Available The present work experimentally investigated the effect of temperature change on the geometric structure of isolated mixing regions (IMRs in a stirred vessel by the decolorization of fluorescent green dye by acid-base neutralization. A four-bladed Rushton turbine was installed in an unbaffled stirred vessel filled with glycerin as a working fluid. The temperature of working fluid was changed in a stepwise manner from 30°C to a certain fixed value by changing the temperature of the water jacket that the vessel was equipped with. The step temperature change can dramatically reduce the elimination time of IMRs, as compared with a steady temperature operation. During the transient process from an initial state to disappearance of IMR, the IMR showed interesting three-dimensional geometrical changes, that are, simple torus with single filament, simple torus without filaments, a combination of crescent shape and circular tori, and doubly entangled torus.

  2. High-level expression and efficient purification of bioactive swollenin in Aspergillus oryzae.

    Science.gov (United States)

    Wang, Meihua; Cai, Jin; Huang, Lei; Lv, Zhengbin; Zhang, Yaozhou; Xu, Zhinan

    2010-11-01

    The bioactivity of swollenin is beneficial to cellulose decomposition by cellulase despite the lack of hydrolytic activity itself. In order to improve the productivity of swollenin, the effects of culture conditions on the expression level in recombinant Aspergillus oryzae were investigated systematically. With regard to the bioactivity of swollenin, glycerin and peanut meal were the optimal carbon or nitrogen source, respectively. The highest level production of swollenin (50 mg L(-1)) was attained after 88 h cultivation with the initial pH of 5.6 in the culture medium. Then the soluble swollenin was effectively purified from the cultural supernatant by ammonium sulfate precipitation and cationic exchange chromatography with recovery yield of 53.2%. The purified swollenin was fully bioactive due to its strong synergistic activity with cellulose.

  3. Fraction of free-base nicotine in fresh smoke particulate matter from the Eclipse "cigarette" by 1H NMR spectroscopy.

    Science.gov (United States)

    Pankow, James F; Barsanti, Kelley C; Peyton, David H

    2003-01-01

    Solution 1H NMR (proton-NMR) spectroscopy was used to measure the distribution of nicotine between its free-base and protonated forms at 20 degrees C in (a) water; (b) glycerin/water mixtures; and (c) puff-averaged "smoke" particulate matter (PM) produced by the Eclipse cigarette, a so-called "harm reduction" cigarette manufactured by R. J. Reynolds (RJR) Tobacco Co. Smoke PM from the Eclipse contains glycerin, water, nicotine, and numerous other components. Smoke PM from the Eclipse yielded a signal for the three N-methyl protons on nicotine at a chemical shift of delta (ppm) = 2.79 relative to a trimethylsilane standard. With alpha fb = fraction of the total liquid nicotine in free-base form, and alpha a = fraction in the acidic, monoprotonated NicH+ form, then alpha a + alpha fb approximately 1. (The diprotonated form of nicotine was assumed negligible.) When the three types of solutions were adjusted so that alpha a approximately 1, the N-methyl protons yielded delta a = 2.82 (Eclipse smoke PM); 2.79 (35% water/65% glycerin); and 2.74 (water). When the solutions were adjusted so that alpha fb approximately 1, the N-methyl protons yielded delta fb = 2.16 (Eclipse smoke PM); 2.13 (35% water/65% glycerin); and 2.10 (water). In all of the solutions, the rate of proton exchange between NicH+ and Nic was fast relative to the 1H-NMR chemical shift difference in hertz. Each solution containing both NicH+ and Nic thus yielded a single N-methyl peak at a delta given by delta = alpha a delta a + alpha fb delta fb so that delta varied linearly between delta a and delta fb. Since alpha fb = (delta a-delta)/(delta a-delta fb), then delta = 2.79 for the unadjusted Eclipse smoke PM indicates alpha fb approximately 0.04. The effective pH of the Eclipse smoke PM at 20 degrees C may then be calculated as pHeff = 8.06 + log[alpha fb/(1-alpha fb)] = 6.69, where 8.06 is the pKa of NicH+ in water at 20 degrees C. The measurements obtained for the puff-averaged Eclipse smoke PM

  4. Preparation and characterization of polymer blends based on recycled PET and polyester derived by terephthalic acid; Preparacao e caracterizacao de blendas polimericas a base de PET reciclado e poliester derivado do acido tereftalico

    Energy Technology Data Exchange (ETDEWEB)

    Ohara, L.; Miranda, C.S.; Fiuza, R.P.; Luporini, S.; Carvalho, R.F.; Jose, N.M., E-mail: leandro.ohara@gmail.co [Universidade Federal da Bahia (GECIM/UFBA), Salvador, BA (Brazil). Inst. de Quimica. Grupo de Energia e Ciencias dos Materiais

    2010-07-01

    Environmentally friendly materials, made from industrial waste, are being increasingly used as a solution to the growing amount of waste generated by society, but also as a cheaper alternative to replace conventional materials for use in construction. In this work were investigated the properties of polymer blends based on recycled PET and a polyester derived from terephthalic acid and glycerin, a co-product of biodiesel. The samples were characterized by XRD, TGA, DSC, FTIR and SEM. The polyester synthesized showed a degradation event near 300 deg C. The blends with higher ratio of PET showed thermal behavior similar to pure PET. The X-ray diffraction showed that the polymer blends are semicrystalline materials. The micrographs presents the presence of a smooth surface, indicating the possibility of miscibility between the arrays. Therefore, the blending makes possible the fabrication of low-cost materials with applications in several areas. (author)

  5. Porous core-shell carbon fibers derived from lignin and cellulose nanofibrils

    KAUST Repository

    Xu, Xuezhu; Zhou, Jian; Jiang, Long; Lubineau, Gilles; Chen, Ye; Wu, Xiangfa; Piere, Robert

    2013-01-01

    This letter reports a method to produce lignin and cellulose nanofibrils (CNFs) based porous core-shell carbon fibers via co-electrospinning followed by controlled carbonization. Lignin formed the shell of the fiber while CNF network formed the porous core. Polyacrylonitrile (PAN) was added to the lignin solution to increase its electrospinability. CNFs were surface acetylated and dispersed in silicon oil to obtain a homogenous dispersion for electrospinning the porous core. Hollow lignin fibers were also electrospun using glycerin as the core material. FT-IR measurements confirmed the CNF acetylation. SEM micrographs showed the core-shell and hollow fiber nanostructures before and after carbonization. The novel carbon fibers synthesized in this study exhibited increased surface area and porosity that are promising for many advanced applications. © 2013 Elsevier B.V.

  6. Biodiesel production by two-stage transesterification with ethanol by washing with neutral water and water saturated with carbon dioxide.

    Science.gov (United States)

    Mendow, G; Veizaga, N S; Sánchez, B S; Querini, C A

    2012-08-01

    Industrial production of ethyl esters is impeded by difficulties in purifying the product due to high amounts of soap formed during transesterification. A simple biodiesel wash process was developed that allows successful purification of samples containing high amounts of soap. The key step was a first washing with neutral water, which removed the soaps without increasing the acidity or affecting the process yield. Afterward, the biodiesel was washed with water saturated with CO(2), a mild acid that neutralized the remaining soaps and extracted impurities. The acidity, free-glycerine, methanol and soaps concentrations were reduced to very low levels with high efficiency, and using non-corrosive acids. Independently of the initial acidity, it was possible to obtain biodiesel within EN14214 specifications. The process included the recovery of soaps by hydrolysis and esterification, making it possible to obtain the theoretical maximum amount of biodiesel. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. Guidelines for Feeding Very Low Birth Weight Infants

    Directory of Open Access Journals (Sweden)

    Sourabh Dutta

    2015-01-01

    Full Text Available Despite the fact that feeding a very low birth weight (VLBW neonate is a fundamental and inevitable part of its management, this is a field which is beset with controversies. Optimal nutrition improves growth and neurological outcomes, and reduces the incidence of sepsis and possibly even retinopathy of prematurity. There is a great deal of heterogeneity of practice among neonatologists and pediatricians regarding feeding VLBW infants. A working group on feeding guidelines for VLBW infants was constituted in McMaster University, Canada. The group listed a number of important questions that had to be answered with respect to feeding VLBW infants, systematically reviewed the literature, critically appraised the level of evidence, and generated a comprehensive set of guidelines. These guidelines form the basis of this state-of-art review. The review touches upon trophic feeding, nutritional feeding, fortification, feeding in special circumstances, assessment of feed tolerance, and management of gastric residuals, gastro-esophageal reflux, and glycerin enemas.

  8. The hard choice for alternative biofuels to diesel in Brazil.

    Science.gov (United States)

    Carioca, J O B; Hiluy Filho, J J; Leal, M R L V; Macambira, F S

    2009-01-01

    This paper selects biofuel scenarios to substitute diesel in Brazil based on oil reserves increase, diesel imports, CO(2) emissions, crops agronomic yields, byproducts marketing and social impacts. This hard task still considers that agricultural practices in developing countries have large social impacts. Brazil presents high consumption of diesel oil in transport; low agronomic yield of traditional vegetable oil crops, which demand large cultivation areas contrasting with microalgae and palm oils which present high productivity. Concerning technologies, thermal cracking and transesterification of vegetable oils present a difficult economic situation related to vegetable oils price, food competition and glycerin market; BTL technology, meaning thermal gasification of biomass to liquids, faces problems related to low density of biomaterials and low viscosity of synthetic biodiesel produced. Biorefinery algal integrated systems and co-solvent technology to introduce up to 8% of ethanol into diesel seem to be feasible routes to reduce diesel consumption.

  9. Bonding in inorganic compounds: a study by x-ray photoelectron spectroscopy

    International Nuclear Information System (INIS)

    Avanzino, S.C.

    1978-10-01

    Core electron binding energies were measured for a variety of inorganic and organometallic compounds using gas-phase X-ray photoelectron spectroscopy (XPS). The atomic charge distributions in these molecules are deduced from the binding energies, often leading to a better understanding of the bonding in these compounds. The XPS spectra of fifteen volatile tin compounds were recorded. The data suggest that the metal d orbitals are not significantly involved in the bonding. The oxygen ls XPS spectra of gaseous CH 3 Mn(CO) 5 , [π-C 5 H 5 Fe(CO) 2 ] 2 , and Co 4 (CO) 12 can be readily resolved into separate peaks due to bridging and terminal carbonyl groups. The C ls spectrum of Fe(CO) 5 consists of a single symmetric peak. The carbonyl ligand core binding energies of transition-metal carbonyl complexes are sensitive to differences in the metal-to-CO ligand bonding. Both C ls and O ls carbonyl binding energies correlate well with average C-O stretching force constants or average C-O stretching frequencies. The metal and carbonyl binding energies in a series of pentacarbonylmanganese complexes LMn(CO) 5 are a good measure of the relative electronegativities of the ligands L. High-quality X-ray photoelectron spectra have been obtained for compounds dissolved in glycerin solutions, and aqueous solutions were converted into glycerin solutions which gave good XRSspectra of the solutes. The technique appears promising as a future analytical application of X-ray photoelectron spectroscopy. The shifts in the binding energies of oxygen, chlorine, and carbon atoms in some isoelectronic isostructural compounds can be explained in terms of simple trends in atomic charges

  10. Formulation of Polyherbal Patches Based on Polyvinyl Alcohol and Hydroxypropylmethyl Cellulose: Characterization and In Vitro Evaluation.

    Science.gov (United States)

    Suksaeree, Jirapornchai; Nawathong, Noramon; Anakkawee, Rinrada; Pichayakorn, Wiwat

    2017-10-01

    The purpose of this research was to prepare and characterize polyherbal patches made from polyvinyl alcohol (PVA) and hydroxypropylmethyl cellulose (HPMC) with glycerine as a plasticizer. Polyherbal extracts were Luk-Pra-Kob recipes extracted with 95% ethanol. They were prepared by mixing the polymer solutions and glycerine in a beaker; subsequently, the polyherbal extracts were homogeneously mixed. Then, they were transferred into a Petri dish and dried in a hot-air oven at 70 ± 2°C for 5 h. The dry polyherbal patches were evaluated for physicochemical properties by Fourier transform infrared spectroscopy, differential scanning calorimetry, X-ray diffraction, and a scanning electron microscope. They were studied for in vitro release and skin permeation of the marker active compound (E)-4-(3',4'-dimethoxyphenyl)but-3-en-l-ol (compound D) using a modified Franz-type diffusion cell. The polyherbal patches made from PVA as a matrix layer were homogeneous, smooth, and compact relative to HPMC-containing polyherbal patches. The selected polyherbal patches made from PVA produced a release profile with an initial burst effect in which compound D release was 74.21 ± 6.13% within 8 h, but compound D could permeate the pig skin only 37.28 ± 5.52% and was highly accumulated in newborn pig skin at 35.90 ± 6.72%. The in vitro release and skin permeation kinetics of compound D were fitted to the Higuchi model. The polyherbal patches made from PVA could be suitably used for herbal medicine application.

  11. Phytochemical analysis and antibacterial activities extracts of mangrove leaf against the growth of some pathogenic bacteria.

    Science.gov (United States)

    Alizadeh Behbahani, Behrooz; Tabatabaei Yazdi, Farideh; Shahidi, Fakhri; Noorbakhsh, Hamid; Vasiee, Alireza; Alghooneh, Ali

    2018-01-01

    In this study, the effects of water, ethanol, methanol and glycerin at five levels (0, 31.25, 83.33, 125 and 250 ml) were investigated on the efficiency of mangrove leaf extraction using mixture optimal design. The antimicrobial effect of the extracts on Streptococcus pneumoniae, Enterococcus faecium and Klebsiella pneumoniae was evaluated using disk diffusion, minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) methods. The mangrove leaf extraction components were identified through gas chromatography/mass spectrometry (GC/MS). Phytochemical analysis (alkaloids, tannins, saponins, flavone and glycosides) were evaluated based on qualitative methods. Antioxidant activity of extracts was measured using 2,2-diphenyl-1-picrylhydrazyl (DPPH), ferric reducing antioxidant potential (FRAP) methods. Maximum antimicrobial effect was observed in Enterococcus faecium and highest resistance against mangrove leaf extract in Enterococcus faecium and Klebsiella pneumoniae, respectively. Increasing concentration of mangrove extracts had a significant effect (p ≤ 0.05) on inhibition zone diameter. The MICs of the mangrove leaf extraction varied from 4 mg/ml to 16 mg/ml. The optimum formulation was found to contain glycerin (0 ml), water (28.22 ml), methanol (59.83 ml) and ethanol (161.95 ml). The results showed that the highest antioxidant activity was related to optimum extract of mangrove leaf and ethanolic extract respectively. The results of phytochemical screening of Avicennia marina leaves extract showed the existence of alkaloids, tannins, saponins, flavone and glycosides. 2-Propenoic acid, 3-phenyl- was the major compound of Avicennia marina. The results of non-significant lack of fit tests, and F value (14.62) indicated that the model was sufficiently accurate. In addition, the coefficient of variations (16.8%) showed an acceptable reproducibility. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Radiation inactivation of microorganisms on food materials with different dry conditions

    Energy Technology Data Exchange (ETDEWEB)

    Ryomoto, Yasuhisa; Ito, Hitoshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2001-09-01

    The effect of dry condition of food materials such as spices or herbs with grain or powder were investigated for inactivation of microorganisms by gamma-rays or electron-beams. Radiation sensitivities on endospores of Bacillus pumilus and B. cereus at polished rice, whole black pepper and glass fiber filter dried with additives of 2% peptone + 1% glycerin were almost equivalent, and D{sub 10} values of gamma-rays were obtained to be 1.8 - 2.2 kGy for B. pumilus and 1.2 - 1.3 kGy for B. cereus, respectively. However, D{sub 10} value was decreased to 1.6 kGy for B. pumilus and 1.0 kGy for B. cereus in white pepper powder, and increased significantly as 2.6 kGy for B. pumilus and 1.8 kGy for B. cereus in senna herb powder. In the case of B. megaterium, Enterobacter cloacae and Escherichia coli, D{sub 10} values were increased at all of food materials even in white pepper powder compared with glass fiber filter with additives. These results are indicating that glycerin and related radical scavengers in food components protect the bacteria such as B. megaterium, Ent. cloacae and E. coli more significantly from effects of radiation than B. pumilus or B. cereus. The increase of radiation resistance of these bacteria should be responsible also to the amount of oxygen penetration in bacterial cells which dried at different conditions. On the irradiation of electron-beams, radiation resistance of all of bacteria increased more significantly than gamma-rays which depending to dose rate effects on bacteria. However, increase of radiation resistance was not observed at Aspergillus oryzae in all of food materials at different dry conditions. (author)

  13. Recovery of different waste vegetable oils for biodiesel production: a pilot experience in Bahia State, Brazil.

    Science.gov (United States)

    Torres, Ednildo Andrade; Cerqueira, Gilberto S; Tiago, M Ferrer; Quintella, Cristina M; Raboni, Massimo; Torretta, Vincenzo; Urbini, Giordano

    2013-12-01

    In Brazil, and mainly in the State of Bahia, crude vegetable oils are widely used in the preparation of food. Street stalls, restaurants and canteens make a great use of palm oil and soybean oil. There is also some use of castor oil, which is widely cultivated in the Sertão Region (within the State of Bahia), and widely applied in industry. This massive use in food preparation leads to a huge amount of waste oil of different types, which needs either to be properly disposed of, or recovered. At the Laboratorio Energia e Gas-LEN (Energy & Gas lab.) of the Universidade Federal da Bahia, a cycle of experiments were carried out to evaluate the recovery of waste oils for biodiesel production. The experiences were carried out on a laboratory scale and, in a semi-industrial pilot plant using waste oils of different qualities. In the transesterification process, applied waste vegetable oils were reacted with methanol with the support of a basic catalyst, such as NaOH or KOH. The conversion rate settled at between 81% and 85% (in weight). The most suitable molar ratio of waste oils to alcohol was 1:6, and the amount of catalyst required was 0.5% (of the weight of the incoming oil), in the case of NaOH, and 1%, in case of KOH. The quality of the biodiesel produced was tested to determine the final product quality. The parameters analyzed were the acid value, kinematic viscosity, monoglycerides, diglycerides, triglycerides, free glycerine, total glycerine, clearness; the conversion yield of the process was also evaluated. Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. Influence of Light Intensity on Growth and Pigment Production by Monascus ruber in Submerged Fermentation.

    Science.gov (United States)

    Bühler, Rose Marie Meinicke; Müller, Bruna Luíse; Moritz, Denise Esteves; Vendruscolo, Francielo; de Oliveira, Debora; Ninow, Jorge Luiz

    2015-07-01

    To reduce environmental problems caused by glycerine accumulation and to make the production of biodiesel more profitable, crude glycerin without treatment was used as substrate for obtaining higher value-added bioproducts. Monascus ruber is a filamentous fungus that produces pigments, particularly red ones, which are used for coloring foods (rice wine and meat products). The interest in developing pigments from natural sources is increasing due to the restriction of using synthetic dyes. The effects of temperature, pH, microorganism morphology, aeration, nitrogen source, and substrates have been studied in the cultivation of M. ruber. In this work, it was observed that light intensity is also an important factor that should be considered for understanding the metabolism of the fungus. In M. ruber cultivation, inhibition of growth and pigment production was observed in Petri dishes and blaffed flasks exposed to direct illumination. Growth and pigment production were higher in Petri dishes and flasks exposed to red light and in the absence of light. Radial growth rate of M. ruber in plates in darkness was 1.50 mm day(-1) and in plates exposed to direct illumination was 0.59 mm day(-1). Maximum production of red pigments (8.32 UA) and biomass (8.82 g L(-1)) were obtained in baffled flasks covered with red film and 7.17 UA of red pigments, and 7.40 g L(-1) of biomass was obtained in flasks incubated in darkness. Under conditions of 1248 lux of luminance, the maximum pigment production was 4.48 UA, with production of 6.94 g L(-1) of biomass, indicating that the fungus has photoreceptors which influence the physiological responses.

  15. Rheological behavior and stability of ciprofloxacin suspension: Impact of structural vehicles and flocculating agent

    Directory of Open Access Journals (Sweden)

    Eskandar Moghimipour

    2013-01-01

    Full Text Available Ciprofloxacin is a fluoroquinolone and is used against a broad spectrum of gram-negative and gram-positive bacteria. The aim of the study is to investigate the effect of structural vehicles and other formulating factors on physical stability and rheological behavior of ciprofloxacin suspension. To formulate the suspensions, the effect of glycerin and polysorbate 80 as wetting agents was evaluated. Then to achieve controlled flocculation, different concentrations of sodium chloride and calcium chloride were added. After choosing suitable wetting and flocculating agents, structural vehicles such as sodium carboxyl methyl cellulose (NaCMC, hydroxypropylmethylcellulose (HPMC and Veegum were evaluated. Physical stability parameters such as sedimentation volume, the degree of flocculation and the ease of redispersion of the suspensions and growth of crystals were evaluated. After incorporation of structural vehicles, the rheological properties of formulations containing were also studied to find out their rheological behavior. According to the results, suspension containing glycerin (0.2% w/v and sodium chloride (0.05% w/v as wetting agent and flocculating agent, respectively, were the most stable formulations regarding their F and N. Microscopic observations showed the growth of crystals in ciprofloxacin suspension in formulation without excipients and the minimum amount of crystal growth was seen in suspension containing NaCMC (0.25% w/v, Veegum (0.1% w/v and NaCl (0.05% w/v. Rheological studies showed that almost all of the formulations had psuedoplastic behavior with different degree of thixotropy. The formulation containing NaCMC (0.25% w/v, Veegum (0.1% w/v and NaCl (0.05% w/v was the most stable formulation. It may be concluded that by altering the amount ratios of formulation factors, the best rheological behavior and the most proper thixotropy may be achieved.

  16. Rheological behavior and stability of ciprofloxacin suspension: Impact of structural vehicles and flocculating agent.

    Science.gov (United States)

    Moghimipour, Eskandar; Rezaee, Saeed; Salimi, Anayatollah; Asadi, Elham; Handali, Somayeh

    2013-07-01

    Ciprofloxacin is a fluoroquinolone and is used against a broad spectrum of gram-negative and gram-positive bacteria. The aim of the study is to investigate the effect of structural vehicles and other formulating factors on physical stability and rheological behavior of ciprofloxacin suspension. To formulate the suspensions, the effect of glycerin and polysorbate 80 as wetting agents was evaluated. Then to achieve controlled flocculation, different concentrations of sodium chloride and calcium chloride were added. After choosing suitable wetting and flocculating agents, structural vehicles such as sodium carboxyl methyl cellulose (NaCMC), hydroxypropylmethylcellulose (HPMC) and Veegum were evaluated. Physical stability parameters such as sedimentation volume, the degree of flocculation and the ease of redispersion of the suspensions and growth of crystals were evaluated. After incorporation of structural vehicles, the rheological properties of formulations containing were also studied to find out their rheological behavior. According to the results, suspension containing glycerin (0.2% w/v) and sodium chloride (0.05% w/v) as wetting agent and flocculating agent, respectively, were the most stable formulations regarding their F and N. Microscopic observations showed the growth of crystals in ciprofloxacin suspension in formulation without excipients and the minimum amount of crystal growth was seen in suspension containing NaCMC (0.25% w/v), Veegum (0.1% w/v) and NaCl (0.05% w/v). Rheological studies showed that almost all of the formulations had psuedoplastic behavior with different degree of thixotropy. The formulation containing NaCMC (0.25% w/v), Veegum (0.1% w/v) and NaCl (0.05% w/v) was the most stable formulation. It may be concluded that by altering the amount ratios of formulation factors, the best rheological behavior and the most proper thixotropy may be achieved.

  17. Batch, design optimization, and DNA sequencing study for continuous 1,3-propanediol production from waste glycerol by a soil-based inoculum.

    Science.gov (United States)

    Kanjilal, Baishali; Noshadi, Iman; Bautista, Eddy J; Srivastava, Ranjan; Parnas, Richard S

    2015-03-01

    1,3-propanediol (1,3-PD) was produced with a robust fermentation process using waste glycerol feedstock from biodiesel production and a soil-based bacterial inoculum. An iterative inoculation method was developed to achieve independence from soil and selectively breed bacterial populations capable of glycerol metabolism to 1,3-PD. The inoculum showed high resistance to impurities in the feedstock. 1,3-PD selectivity and yield in batch fermentations was optimized by appropriate nutrient compositions and pH control. The batch yield of 1,3-PD was maximized to ~0.7 mol/mol for industrial glycerol which was higher than that for pure glycerin. 16S rDNA sequencing results show a systematic selective enrichment of 1,3-PD producing bacteria with iterative inoculation and subsequent process control. A statistical design of experiments was carried out on industrial glycerol batches to optimize conditions, which were used to run two continuous flow stirred-tank reactor (CSTR) experiments over a period of >500 h each. A detailed analysis of steady states at three dilution rates is presented. Enhanced specific 1,3-PD productivity was observed with faster dilution rates due to lower levels of solvent degeneration. 1,3-PD productivity, specific productivity, and yield of 1.1 g/l hr, 1.5 g/g hr, and 0.6 mol/mol of glycerol were obtained at a dilution rate of 0.1 h(-1)which is bettered only by pure strains in pure glycerin feeds.

  18. Farm-scale thermophilic co-digestion of dairy manure with a biodiesel byproduct in cold regions

    International Nuclear Information System (INIS)

    Andriamanohiarisoamanana, Fetra J.; Yamashiro, Takaki; Ihara, Ikko; Iwasaki, Masahiro; Nishida, Takehiro; Umetsu, Kazutaka

    2016-01-01

    Highlights: • Co-digestion of dairy manure and crude glycerin was conducted using a 60 m"3 reactor. • The highest methane yield was 0.323 m"3/kgVS obtained at 4.2% (v/v) of crude glycerin. • The optimum organic loading rate for crude glycerol was 1.32 kgVS_C_G/m"3 d. • Reactor energy self-sufficiency was observed with net energy output of 25 kW h/d. - Abstract: Conversion of organic wastes into applicable energy sources is the best way to improve organic waste management. In this study, the performance of thermophilic co-digestion of dairy manure (DM) and crude glycerol (CG) in a 60-m"3 farm-scale biogas digester located in a cold region was investigated during the winter. Compared to the anaerobic digestion of DM alone, the methane production increased by approximately twofold during co-digestion of DM and CG. The highest methane yield was 0.323 m"3/kgVS obtained at 4.2% (v/v) of CG. Despite the increase in methane production with organic loading rate, the methane yield of CG reduced remarkably at 2.64 kgVS_C_G/m"3 d, while the highest was at 1.32 kgVS_C_G/m"3 d. During the co-digestion, a net energy at an average of 25 kWh/d was obtained for farm operation, whereas a supply of kerosene and electricity from national grid were required for the digester and farm operations during anaerobic digestion of DM. During winter, the improvement of biogas yield through the addition of CG enabled the sustainability of a farm-scale biogas production system and reduced its environmental impact.

  19. Radiation inactivation of microorganisms on food materials with different dry conditions

    International Nuclear Information System (INIS)

    Ryomoto, Yasuhisa; Ito, Hitoshi

    2001-01-01

    The effect of dry condition of food materials such as spices or herbs with grain or powder were investigated for inactivation of microorganisms by gamma-rays or electron-beams. Radiation sensitivities on endospores of Bacillus pumilus and B. cereus at polished rice, whole black pepper and glass fiber filter dried with additives of 2% peptone + 1% glycerin were almost equivalent, and D 10 values of gamma-rays were obtained to be 1.8 - 2.2 kGy for B. pumilus and 1.2 - 1.3 kGy for B. cereus, respectively. However, D 10 value was decreased to 1.6 kGy for B. pumilus and 1.0 kGy for B. cereus in white pepper powder, and increased significantly as 2.6 kGy for B. pumilus and 1.8 kGy for B. cereus in senna herb powder. In the case of B. megaterium, Enterobacter cloacae and Escherichia coli, D 10 values were increased at all of food materials even in white pepper powder compared with glass fiber filter with additives. These results are indicating that glycerin and related radical scavengers in food components protect the bacteria such as B. megaterium, Ent. cloacae and E. coli more significantly from effects of radiation than B. pumilus or B. cereus. The increase of radiation resistance of these bacteria should be responsible also to the amount of oxygen penetration in bacterial cells which dried at different conditions. On the irradiation of electron-beams, radiation resistance of all of bacteria increased more significantly than gamma-rays which depending to dose rate effects on bacteria. However, increase of radiation resistance was not observed at Aspergillus oryzae in all of food materials at different dry conditions. (author)

  20. Degradation of corn stalk by the composite microbial system of MC1

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The composite microbial system of MC1 was used to degrade corn stalk in order to determine properties of the degraded products as well as bacterial composition of MC1. Results indicated that the pH of the fermentation broth was typical of lignocellulose degradatioin by MC1, decreasing in the early phase and increasing in later stages of the degradation. The microbial biomass peaked on the day 3 after degradation. The MC1 effeciently degraded the corn stalk by nearly 70% during which its cellulose content decreased by 71.2%, hemicellulose by 76.5% and lignin by 24.6%. The content of water-soluble carbohydrates (WSC) in the fermentation broth increased progressively during the first three days, and decreased thereafter, suggesting an accumulation of WSC in the early phase of the degradation process. Total levels of various volatile products peaked in the third day after degradation , and 7 types of volatile products were detected in the fermentation broth. These were ethanol, acetic acid, 1,2-ethanediol, propanoic acid, butanoic acid, 3-methyl-butanoic acid and glycerine. Six major compounds were quantitatively analysed and the contents of each compound were ethanol (0.584 g/L), acetic acid (0.735 g/L), 1,2-ethanediol (0.772 g/L), propanoic acid (0.026 g/L), butanoic acid (0.018 g/L) and glycerine (4.203 g/L). Characterization of bacterial cells collected from the culture solution, based on 16S rDNA PCR-DGGE analysis of DNAs, showed that the composition of bacterial community in MC1 coincided basically with observations from previous studies. This indicated that the structure of MC1 is very stable during degradation of different lignocellulose materials.

  1. Experimental Investigation of Propagation and Reflection Phenomena in Finite Amplitude Sound Beams.

    Science.gov (United States)

    Averkiou, Michalakis Andrea

    Measurements of finite amplitude sound beams are compared with theoretical predictions based on the KZK equation. Attention is devoted to harmonic generation and shock formation related to a variety of propagation and reflection phenomena. Both focused and unfocused piston sources were used in the experiments. The nominal source parameters are piston radii of 6-25 mm, frequencies of 1-5 MHz, and focal lengths of 10-20 cm. The research may be divided into two parts: propagation and reflection of continuous-wave focused sound beams, and propagation of pulsed sound beams. In the first part, measurements of propagation curves and beam patterns of focused pistons in water, both in the free field and following reflection from curved targets, are presented. The measurements are compared with predictions from a computer model that solves the KZK equation in the frequency domain. A novel method for using focused beams to measure target curvature is developed. In the second part, measurements of pulsed sound beams from plane pistons in both water and glycerin are presented. Very short pulses (less than 2 cycles), tone bursts (5-30 cycles), and frequency modulated (FM) pulses (10-30 cycles) were measured. Acoustic saturation of pulse propagation in water is investigated. Self-demodulation of tone bursts and FM pulses was measured in glycerin, both in the near and far fields, on and off axis. All pulse measurements are compared with numerical results from a computer code that solves the KZK equation in the time domain. A quasilinear analytical solution for the entire axial field of a self-demodulating pulse is derived in the limit of strong absorption. Taken as a whole, the measurements provide a broad data base for sound beams of finite amplitude. Overall, outstanding agreement is obtained between theory and experiment.

  2. A COMBINED REACTION/PRODUCT RECOVERY PROCESS FOR THE CONTINUOUS PRODUCTION OF BIODIESEL

    Energy Technology Data Exchange (ETDEWEB)

    Birdwell, J.F., Jr.; McFarlane, J.; Schuh, D.L.; Tsouris, C; Day, J.N. (Nu-Energie, LLC); Hullette, J.N. (Nu-Energie, LLC)

    2009-09-01

    Oak Ridge National Laboratory (ORNL) and Nu-Energie, LLC entered into a Cooperative Research And Development Agreement (CRADA) for the purpose of demonstrating and deploying a novel technology for the continuous synthesis and recovery of biodiesel from the transesterification of triglycerides. The focus of the work was the demonstration of a combination Couette reactor and centrifugal separator - an invention of ORNL researchers - that facilitates both product synthesis and recovery from reaction byproducts in the same apparatus. At present, transesterification of triglycerides to produce biodiesel is performed in batch-type reactors with an excess of a chemical catalyst, which is required to achieve high reactant conversions in reasonable reaction times (e.g., 1 hour). The need for long reactor residence times requires use of large reactors and ancillary equipment (e.g., feed and product tankage), and correspondingly large facilities, in order to obtain the economy of scale required to make the process economically viable. Hence, the goal of this CRADA was to demonstrate successful, extended operation of a laboratory-scale reactor/separator prototype to process typical industrial reactant materials, and to design, fabricate, and test a production-scale unit for deployment at the biodiesel production site. Because of its ease of operation, rapid attainment of steady state, high mass transfer and phase separation efficiencies, and compact size, a centrifugal contactor was chosen for intensification of the biodiesel production process. The unit was modified to increase the residence time from a few seconds to minutes*. For this application, liquid phases were introduced into the reactor as separate streams. One was composed of the methanol and base catalyst and the other was the soy oil used in the experiments. Following reaction in the mixing zone, the immiscible glycerine and methyl ester products were separated in the high speed rotor and collected from separate

  3. A COMBINED REACTION/PRODUCT RECOVERY PROCESS FOR THE CONTINUOUS PRODUCTION OF BIODIESEL

    International Nuclear Information System (INIS)

    Birdwell, J.F. Jr.; McFarlane, J.; Schuh, D.L.; Tsouris, C.; Day, J.N.; Hullette, J.N.

    2009-01-01

    Oak Ridge National Laboratory (ORNL) and Nu-Energie, LLC entered into a Cooperative Research And Development Agreement (CRADA) for the purpose of demonstrating and deploying a novel technology for the continuous synthesis and recovery of biodiesel from the transesterification of triglycerides. The focus of the work was the demonstration of a combination Couette reactor and centrifugal separator - an invention of ORNL researchers - that facilitates both product synthesis and recovery from reaction byproducts in the same apparatus. At present, transesterification of triglycerides to produce biodiesel is performed in batch-type reactors with an excess of a chemical catalyst, which is required to achieve high reactant conversions in reasonable reaction times (e.g., 1 hour). The need for long reactor residence times requires use of large reactors and ancillary equipment (e.g., feed and product tankage), and correspondingly large facilities, in order to obtain the economy of scale required to make the process economically viable. Hence, the goal of this CRADA was to demonstrate successful, extended operation of a laboratory-scale reactor/separator prototype to process typical industrial reactant materials, and to design, fabricate, and test a production-scale unit for deployment at the biodiesel production site. Because of its ease of operation, rapid attainment of steady state, high mass transfer and phase separation efficiencies, and compact size, a centrifugal contactor was chosen for intensification of the biodiesel production process. The unit was modified to increase the residence time from a few seconds to minutes*. For this application, liquid phases were introduced into the reactor as separate streams. One was composed of the methanol and base catalyst and the other was the soy oil used in the experiments. Following reaction in the mixing zone, the immiscible glycerine and methyl ester products were separated in the high speed rotor and collected from separate

  4. Life cycle assessment of rapeseed oil, rape methyl ester and ethanol as fuels - a comparison between large- and smallscale production

    Energy Technology Data Exchange (ETDEWEB)

    Bernesson, Sven [Swedish Univ. of Agriculture Sciences, Uppsala (Sweden). Dep. of Biometry and Engineering

    2004-05-01

    Production of rapeseed oil, rape methyl ester (RME) and ethanol fuel for heavy diesel engines can be carried out with different systems solutions, in which the choice of system is usually related to the scale of the production. The main purpose of this study was to analyse whether the use of a small-scale rapeseed oil, RME and ethanol fuel production system reduced the environmental load in comparison to a medium- and a large-scale system. To fulfil this purpose, a limited LCA, including air-emissions and energy requirements, was carried out for the three fuels and the three plant sizes. Four different methods to allocate the environmental burden between different products were compared: physical allocation according to the lower heat value in the products [MJ/kg], economic allocation according to the product prices [SEK/kg], no allocation and allocation with a system expansion so that rapemeal and distiller's waste could replace soymeal mixed with soyoil and glycerine could replace glycerine produced from fossil raw material. The functional unit, to which the total environmental load was related, was 1.0 MJ of energy delivered on the engine shaft to the final consumer. Production of raw materials, cultivation, transport, fuel production and use of the fuels produced were included in the systems studied. It was shown in the study that the differences in environmental impact and energy requirement between small-, medium- and large-scale systems were small or even negligible in most cases for all three fuels, except for the photochemical ozone creation potential (POCP) during ethanol fuel production. The longer transport distances to a certain degree outweighed the higher oil extraction efficiency, the higher energy efficiency and the more efficient use of machinery and buildings in the large-scale system. The dominating production step was the cultivation, in which production of fertilisers, followed by soil emissions and tractive power, made major contributions to

  5. Center for Catalysis at Iowa State University

    Energy Technology Data Exchange (ETDEWEB)

    Kraus, George A.

    2006-10-17

    system that performs both esterification (of free fatty acids) and transesterification (of soybean oil) in a one-pot fashion. This will allow the biodiesel producers to use the aforementioned cheap feedstocks without any pretreatment. In addition, the catalyst system is heterogeneous and is highly recyclable and reusable. Although markets currently exist for glycerin, concern is mounting that the price of glycerin may plummet to $.05 - $.10 per pound if future production exceeds demand. Developing a system to make high value chemicals such as 1,3-propanediol from the glycerin stream will add value for biodiesel producers who implement the new technology. Given the fact that both DuPont and Shell chemicals have announced the commercialization of two new PDO-based polymers, a rapid increase of market demand for a cheaper PDO source is very likely. 4. Comparison of actual accomplishments with goals and objectives From our progress reports, the four areas are: 1. Catalyst development (7.4.12.A) 2. Conversion of glycerol (7.4.12.B) 3. Conversion of biodiesel (7.4.12.C) 4. Glucose from starch (7.4.12.D)

  6. Design, construction and implementation of a packed reactor system to study the production of hydrogen by the catalytic reaction of reforming of oxygenated hydrocarbons

    International Nuclear Information System (INIS)

    Salas Aguilar, Cesar Augusto

    2014-01-01

    The Laboratorio de Quimica Inorganica of the Universidad de Costa Rica has evaluated the performance of several types of catalysts and supports in steam reforming reactions, using different conditions for synthesis of the same. The construction of a reaction system at laboratory scale is described to improve the conditions of the reforming process compared to previous projects. Catalysts synthesized and characterized are used but providing better disposal through a packed bed reactor. The system has had the necessary instrumentation for proper measurement of the temperature at the entrance and inside the reactor, proper feeding of reactants, flow measurement and sampling and measurement system. The conceptual design of the reactions system presented has taken into account the income of reactants through a peristaltic pump, preheating or vaporization of reagents, income and measurement of carrier gas sampling, take of sampling, flow measurement product, reactor packed and cooler product. The order of each stage is defined and positioning in the entire system. The design of a preheater and a tubular reactor is detailed, taking into account the dimensions and construction materials of each of the pieces. The design is presented in a series of diagrams and then the result of the construction is illustrated by photographs, all work done also has been described. The implementation of the system has described by the coupling of all parties and the respective tests. A basic experimental plan is presented to evaluate the performance of the reaction system, using glycerin as a reactant, demonstrating ability to react and take effective data. Four experiments are performed: vacuum reactor, packed reactor with two types of filling and reactor with an exposed surface cobalt oxide (II) reduced, the gases produced in the reaction are analyzed by gas chromatography. The results are discussed and analyzed, focusing on the overall selectivity of hydrogen relative to methane, and the

  7. Life cycle assessment of rapeseed oil, rape methyl ester and ethanol as fuels - a comparison between large- and smallscale production

    Energy Technology Data Exchange (ETDEWEB)

    Bernesson, Sven [Swedish Univ. of Agriculture Sciences, Uppsala (Sweden). Dep. of Biometry and Engineering

    2004-05-01

    Production of rapeseed oil, rape methyl ester (RME) and ethanol fuel for heavy diesel engines can be carried out with different systems solutions, in which the choice of system is usually related to the scale of the production. The main purpose of this study was to analyse whether the use of a small-scale rapeseed oil, RME and ethanol fuel production system reduced the environmental load in comparison to a medium- and a large-scale system. To fulfil this purpose, a limited LCA, including air-emissions and energy requirements, was carried out for the three fuels and the three plant sizes. Four different methods to allocate the environmental burden between different products were compared: physical allocation according to the lower heat value in the products [MJ/kg], economic allocation according to the product prices [SEK/kg], no allocation and allocation with a system expansion so that rapemeal and distiller's waste could replace soymeal mixed with soyoil and glycerine could replace glycerine produced from fossil raw material. The functional unit, to which the total environmental load was related, was 1.0 MJ of energy delivered on the engine shaft to the final consumer. Production of raw materials, cultivation, transport, fuel production and use of the fuels produced were included in the systems studied. It was shown in the study that the differences in environmental impact and energy requirement between small-, medium- and large-scale systems were small or even negligible in most cases for all three fuels, except for the photochemical ozone creation potential (POCP) during ethanol fuel production. The longer transport distances to a certain degree outweighed the higher oil extraction efficiency, the higher energy efficiency and the more efficient use of machinery and buildings in the large-scale system. The dominating production step was the cultivation, in which production of fertilisers, followed by soil emissions and tractive power, made major

  8. Design and Integration for Biodiesel Production from Vegetable Oil via Transesterification Reaction

    Directory of Open Access Journals (Sweden)

    F Abbaspour Aghdam

    2018-03-01

    Full Text Available Introduction Biodiesel is Fatty Acid Methyl Esters (FAME which is used as a renewable fuel in diesel engines. Extraction of lipid from various flora sources, including Sunflower, Palm, Canola or animal oils, with a Trans-Esterification reaction between alcohol and Triglyceride (TG, leads to production of Biodiesel and Glycerin. The production cost of biodiesel is so important that is now considered as the greatest obstacle during scale-up process. In this research, a model-type of biodiesel production unit (using vegetable oil source, was designed by Aspen HYSYS V7.2 software, then a great deal of the attempt was employed to optimize the overall yield against the processing parameters including: mass and energy consumption load, as well as some technical discussion regarding associated apparatuses. Materials and Methods Process Design The simulation was carried out using Aspen HYSYS V7.2 employing Triolein (as TG, Oleic acid (as Free Fatty Acid (FFA, and Oleat as biodiesel. Avoiding side-stream reactions as well as trans-esterification, the FFA content was taken to a mere 0.05% (%mass. Feed stream was considered as product of NaOH-catalyzed bi-reactor system operating at 60˚C and 1 atm with the overall conversion of 70% using two series reactors. The ratio of TG to Alcohol is 1:3, however, owing to establish an appropriate reactor performance; this ratio was applied as 1:6 practically. The design was mainly intended to produce 480 m3d-1 biodiesel with mass concentration of 99.65%. Methanol was used in this investigation due to low cost, accessibility and handling considerations. NRTL was taken as the Equation of State (EOS for the process and should be used PRSV equation in the decanter. Thermal Integration Energy consumption was taken into account as basis of optimization in this study. Table 2 demonstrates the thermal characteristics of all streams consist of source and down-streams, while outlet stream like glycerol streams were neglected to

  9. Inversion of the uterus following abortion.

    Science.gov (United States)

    Gupta, A S; Datta, N; Ghosh, D

    1982-10-16

    A case of inversion of the uterus following abortion is reported. The 35-year old patient, admitted October 10, 1978 to the Medical College and Hospitals in Calcutta, India was referred by a private practitioner with a history of amenorrhea for 16 weeks, bleeding for 3 days, expulsion of the fetus 3 days earlier, and something coming down per vaginum for 2 days. The patient was para 4+0 (all full term normal deliveries) and home delivery for the last child 1 1/2 years earlier. She had a history of regular menstrual periods. Her general condition was poor. The examination revealed a gangrenous mass coming out of the vulva with a very offensive smell. There was a raw surface on which placenta like tissue was attached. No active bleeding was seen. Fundus and cervix of the uterus could not be felt. On rectal examination the uterus could not be felt, a cup-like depression was felt at the site of the uterus. The provision diagnosis was inversion of uterus following abortion. Treatment was started with sedatives and antibiotics, and arrangements were made for a blood transfusion. The vaginal mass was covered with glycerine and acriflavine gauze, and a hysterectomy was decided upon after improvement of her general condition and control of the infection. On October 14th, the patient was placed in knee chest position and posterior vaginal wall was retracted with Sims' speculum when the inverted lump was spontaneously reduced within the vagina. The inverted uterus was felt in the region of the vaginal vault. Glycerine acriflavine pack was given which was taken out and repack was given daily until the operation. The hysterectomy was performed on October 23rd. The abdomen was opened up by a transverse incision and the pelvis was explored. In the region of the uterus a cup-shaped depression was noted. Tubes and ovaries of both sides were seen hanging laterally from the cupped area. The left tube was found congested and thickened. Reduction of uterus was done by making a vertical

  10. Acción fundente de cenizas de glicerina de biodiésel en pastas cerámicas

    Directory of Open Access Journals (Sweden)

    Acosta, A.

    2009-06-01

    Full Text Available Biodiesel glycerin ashes are residual ashes generated in the combustion of glycerine that is produced as a by-product in the manufacture of biodiesel. The aim of this work is to check their flux action in ceramic fabrics. In order to do so, both mineralogical and chemical characterisation of these ashes and some ceramic pastes, used in stoneware, has been performed, as well as an assessment of its thermal behaviour. Different mixtures of biodiesel ceramics adding ashes to a paste in a ceramic 5, 7 and 10% by weight have been used. Such mixtures have been studied with a hot stage microscope and it can be concluded that the ash acts as a flux of the ceramic paste reducing its sintering temperature in more than 100 ºC, which in an industrial process would result in energy savings in the firing process and valorisation of waste it as a secondary raw material, in addition to obtaining an environmental benefit reusing waste products and preventing its dumping.

    Las cenizas de glicerina de biodiésel son unas cenizas residuales generadas en la combustión de la glicerina que se obtiene como subproducto en la fabricación de biodiésel. El objetivo de este trabajo es comprobar su acción fundente en pastas cerámicas. Para ello se ha realizado la caracterización mineralógica y química de dichas cenizas y de unas pastas cerámicas destinadas a la fabricación de gres, así como el estudio de su comportamiento térmico. Se han formulado diferentes mezclas adicionando cenizas de glicerina a la pasta cerámica en un 5, 7 y 10 % en peso. Estas mezclas se han estudiado con el microscopio de calefacción de manera comparada y se concluye que la ceniza actúa como fundente de la pasta cerámica reduciendo su temperatura de sinterización en más de 100ºC, lo cual en un proceso industrial se traduciría en un ahorro energético en la cocción y en la valorización de un residuo al considerarlo como una materia prima secundaria, además de obtener un

  11. Characterization of viscous biofuel sprays using digital imaging in the near field region

    International Nuclear Information System (INIS)

    Sallevelt, J.L.H.P.; Pozarlik, A.K.; Brem, G.

    2015-01-01

    Highlights: • Biodiesel, vegetable oil and glycerin sprays have been studied using PDIA. • The study is focused on the effect of fuel viscosity on the spray characteristics. • Viscosity has a strong effect on the breakup length in pressure-swirl atomization. • The results are compared to combustion experiments with a micro gas turbine. • The penetration depth of ligaments can be a critical factor in burning viscous fuel. - Abstract: The atomization of biodiesel, vegetable oil and glycerin has been studied in an atmospheric spray rig by using digital imaging (PDIA). Images of the spray were captured in the near field, just 18 mm downstream of the atomizer, and processed to automatically determine the size of both ligaments and droplets. The effect of the spray structure in this region is of major interest for the combustion of biofuels in gas turbines. The sprays were produced by a pressure-swirl atomizer that originates from the multifuel micro gas turbine (MMGT) setup. Various injection conditions have been tested to investigate the influence of viscosity on the spray characteristics and to assess the overall performance of the atomizer. The spray measurements have been compared to combustion experiments with biodiesel and vegetable oil in the micro gas turbine at similar injection conditions. The results show that the primary breakup process rapidly deteriorates when the viscosity is increased. A higher viscosity increases the breakup length, which becomes visible at the measurement location in the form of ligaments. This effect leads to an unacceptable spray quality once the viscosity slightly exceeds the typical range for conventional gas turbine fuels. The SMD in the investigated spray region was not significantly affected by viscosity, but mainly influenced by injection pressure. The data furthermore indicate an increase in SMD with surface tension. It was found that the penetration depth of ligaments can have major impact on the combustion process

  12. Study of tape casting of Yttria stabilized zirconia for apply in solid oxide fuel cell

    International Nuclear Information System (INIS)

    Santana, Leonardo de Paulo

    2008-01-01

    and a plasticizer have to be added to the suspensions to produce YSZ substrates. Poly(viny alcohol) (PVA) and glycerine were used as binder and plasticizer, respectively, in this work. By the effect of both additives, at a glycerine to PVA rate of 2,25:1, it was possible to produce YSZ substrates. (author)

  13. Isolamento e estudo experimental de duas novas culturas de bacilos ácido-alcool resistentes de muco nasal de leprosos

    Directory of Open Access Journals (Sweden)

    H. C. de Souza-Araujo

    1954-03-01

    Full Text Available The A. described on December 14, 1951, his first culture of acid-fast bacillus isolated from nasal mucus of a leprous girl. in this paper the A. describes two new strains of acid-fast bacilli gotten also from nasal mucus of other two leprous girls, L3 cases. The first patient (layse S had her mucus treated by petroff's method on December 16, 1952 and sown onto three tubes of loewenstein medium and in glycerin broth. After two weeks incubation at 37°C all three tubes of Loewenstein showed many punctiforme and pin-head yellowish colonies, whose microscopic examination proved to be of a pure acid-fast bacillus culture. This sample inoculated in rats and mice produced, after 55 days incubation, small tumors from which the culture was easily recovered. On April, 9, 1953 a new sample of nasal mucus of the same patient was sown in three tubes of Loewenstein. After two weeks incubation at 37°C all 3 tubes showed germination of small yellowish colonies of acid-fast bacilli. Within four months being gotten two samples of identical cultures in all smeared tubes of Loewenstein medium sown, proved that such cultures were not an ordinary ambient contamination. Second patient: - Maria N. After various sowing of different kinds of material from her, february 26, 1953 her nasal mucus treated by soda and sown onto Loewenstein medium, after 25 days incubation showed in only one tube, one small round colony, at first white, becoming creamy after three months. Transplants in various media grew at first slowly and after 2 or 3 generations grew faster. The "Layse" strain produced pellicle in glycerin broth and Dubos medium; the "Maria N." strain did not produce as yet. Both strains (Layse I and II, and Maria N. gave weak positive Dubos test in half-an-hour and negative after 24 hours reading. Both were strongly positive when stained by Gram, Ziehl-Neelsen and Fontes methods. Both strains gave also positive fluoroscopy. These cultures are being studied. The A

  14. Optimization of mass-production conditions for tritium breeder pebbles based on slurry droplet wetting method

    Energy Technology Data Exchange (ETDEWEB)

    Park, Yi-Hyun, E-mail: yhpark@nfri.re.kr [National Fusion Research Institute, Daejeon (Korea, Republic of); Min, Kyung-Mi; Ahn, Mu-Young; Cho, Seungyon; Lee, Young-Min [National Fusion Research Institute, Daejeon (Korea, Republic of); Park, Sang-Jin; Danish, Rehan; Lim, Chul-Hwan; Jo, Yong-Dae [IVT Co., Ltd., Daegu (Korea, Republic of)

    2016-11-01

    Highlights: • An automatic dispensing system was developed to improve uniformity and production rate of breeder pebbles. • The production rate of this system for Li{sub 2}TiO{sub 3} pebble was estimated at 50 kg/year. • The optimization of dispensing and sintering conditions for the mass-production of Li{sub 2}TiO{sub 3} pebble was conducted. • Integrity of Li{sub 2}TiO{sub 3} pebble was able to be ensured during mass-production process, especially during batch process. - Abstract: Lithium metatitanate (Li{sub 2}TiO{sub 3}) is being considered as tritium breeding material for solid-type breeding blanket, which are used in pebble-bed form. The total amount of Li{sub 2}TiO{sub 3} pebbles in Helium Cooled Ceramic Reflector (HCCR) Test Blanket Module (TBM) is approximately 80 kg. Furthermore, DEMO reactor requires a great deal of breeder pebbles. Therefore, the development of mass-production system for breeder pebbles is necessary. The slurry droplet wetting method was adopted in the mass-production process for Li{sub 2}TiO{sub 3} pebbles, which had been developed in Korea. In this method, an automatic slurry dispensing system is one of the key apparatuses because the uniformity of pebbles and production rate are able to be improved. The system was successfully manufactured, which was consisted of a dispensing unit for instillation of Li{sub 2}TiO{sub 3} slurry, a glycerin bath for hardening of droplets, and an automatic maintaining unit for constant distance between syringe needle and glycerin surface. The production rate of this system for Li{sub 2}TiO{sub 3} pebble was estimated at 50 kg/year. In this study, it was investigated that the effect of dispensing and sintering conditions on the mass-production of Li{sub 2}TiO{sub 3} pebbles.

  15. Electronic Cigarettes: Their Constituents and Potential Links to Asthma.

    Science.gov (United States)

    Clapp, Phillip W; Jaspers, Ilona

    2017-10-05

    Vaping is gaining popularity in the USA, particularly among teens and young adults. While e-cigs are commonly represented as safer alternatives to tobacco cigarettes, little is known regarding the health effects of their short- or long-term use, especially in individuals with pre-existing respiratory diseases such as asthma. Flavored e-cig liquids (e-liquids) and e-cig aerosols contain airway irritants and toxicants that have been implicated in the pathogenesis and worsening of lung diseases. In this review, we will summarize existing data on potential health effects of components present in e-cig aerosols, such as propylene glycol, vegetable glycerin, nicotine, and flavorings, and discuss their relevance in the context of asthma. Recent survey data indicate that adolescents with asthma had a higher prevalence of current e-cig use (12.4%) compared to their non-asthmatics peers (10.2%) and conveyed positive beliefs about tobacco products, especially e-cigs. Similarly, a study conducted among high school students from Ontario, Canada, indicated a greater likelihood of e-cig use in asthmatics as compared to their non-asthmatic peers. Availability of different flavorings is often cited as the main reason among youth/adolescents for trying e-cigs or switching from cigarettes to e-cigs. Occupational inhalation of some common food-safe flavoring agents is reported to cause occupational asthma and worsen asthmatic symptoms. Moreover, workplace inhalation exposures to the flavoring agent diacetyl have caused irreversible obstructive airway disease in healthy workers. Additionally, recent studies report that thermal decomposition of propylene glycol (PG) and vegetable glycerin (VG), the base constituents of e-liquids, produces reactive carbonyls, including acrolein, formaldehyde, and acetaldehyde, which have known respiratory toxicities. Furthermore, recent nicotine studies in rodents reveal that prenatal nicotine exposures lead to epigenetic reprogramming in the offspring

  16. [The Distribution of Pediculus humanus capitis Among Primary School Pupils of the Turkish Chamber of Commerce and Stock Exchange Organisation in Van].

    Science.gov (United States)

    Karaaslan, Selver; Yılmaz, Hasan

    2015-03-01

    This study was performed in order to study the prevalence of Pediculus humanus capitis (P. h. capitis). The study was carried out on pupils between 5-15 years old in a school and kindergarden belonging to the Turkish Chamber of Commerce and Stock Exchange Organization in Van City between November-December 2007. The hair of 863 pupils (especially the neck and the back of head areas), 385 girls and 478 boys, were examined for eggs, nymphs and adults of P. h. capitis. A questionnaire was given to the pupils, which was collected the following day. Lice and their eggs/nits, which were removed from the head of children were transferred to a bottle containing 5% glycerin in 70% ethyl alcohol. Later they were sent to the Parasitology Laboratory of the Health Research and Training Hospital of Yüzüncü Yıl University. Eggs/nits were found in 164 (42.6%) of the girls and in 34 (7.1%) of the boys (overall 198 (22.9%) infested pupils). The prevalence of P. h. capitis was high, especially in girls. The infestation rates observed and the evaluation of the questionnaire showed that there is a statistically significant relationships between pediculosis capitis and sex, level of family income, education level of the mother, number of baths taken per weekly, number of family members living in the same home, room number per capita, and hair length (p0.05).

  17. Spontaneous oscillation of tension and sarcomere length in skeletal myofibrils. Microscopic measurement and analysis.

    Science.gov (United States)

    Anazawa, T; Yasuda, K; Ishiwata, S

    1992-05-01

    We have devised a simple method for measuring tension development of single myofibrils by micromanipulation with a pair of glass micro-needles. The tension was estimated from the deflection of a flexible needle under an inverted phase-contrast microscope equipped with an image processor, so that the tension development is always accompanied by the shortening of the myofibril (auxotonic condition) in the present setup. The advantage of this method is that the measurement of tension (1/30 s for time resolution and about 0.05 micrograms for accuracy of tension measurement; 0.05 microns as a spatial resolution for displacement of the micro-needle) and the observation of sarcomere structure are possible at the same time, and the technique to hold myofibrils, even single myofibrils, is very simple. This method has been applied to study the tension development of glycerinated skeletal myofibrils under the condition where spontaneous oscillation of sarcomeres is induced, i.e., the coexistence of MgATP, MgADP and inorganic phosphate without free Ca2+. Under this condition, we found that the tension of myofibrils spontaneously oscillates accompanied by the oscillation of sarcomere length with a main period of a few seconds; the period was lengthened and shortened with stretch and release of myofibrils. A possible mechanism of the oscillation is discussed.

  18. Preparation and properties of a novel macro porous Ni2+-imprinted chitosan foam adsorbents for adsorption of nickel ions from aqueous solution.

    Science.gov (United States)

    Guo, Na; Su, Shi-Jun; Liao, Bing; Ding, Sang-Lan; Sun, Wei-Yi

    2017-06-01

    In this study, novel macro porous Ni 2+ -imprinted chitosan foam adsorbents (F-IIP) were prepared using sodium bicarbonate and glycerine to obtain a porogen for adsorbing nickel ions from aqueous solutions. The use of the ion-imprinting technique for adsorbents preparation improved the nickel ion selectivity and adsorption capacity. We characterised the imprinted porous foam adsorbents in terms of the effects of the initial pH value, initial metal ion concentration, and contact time on the adsorption of nickel ions. The adsorption process was described best by Langmuir monolayer adsorption models, and the maximum adsorption capacity calculated from the Langmuir equation was 69.93mgg -1 . The kinetic data could be fitted to a pseudo-second-order equation. Our analysis of selective adsorption demonstrated the excellent preference of the F-IIP foams for nickel ions compared with other coexisting metal ions. Furthermore, tests over five cycle runs suggested that the F-IIP foam adsorbents had good durability and efficiency. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Evaluation of thermal properties of food materials at high pressures using a dual-needle line-heat-source method.

    Science.gov (United States)

    Zhu, S; Ramaswamy, H S; Marcotte, M; Chen, C; Shao, Y; Le Bail, A

    2007-03-01

    Thermal properties of food systems at high pressure (HP) are important in the design and operation of HP processing equipment. Available techniques for thermal property evaluation under HP conditions are still very limited. In this study, a dual-needle line-heat-source (DNL) device was installed in an HP vessel to evaluate thermal conductivity (k), diffusivity (alpha), and volumetric heat capacity (C(pV)) of foods at high pressure. The DNL probe was calibrated using glycerin (0.1 MPa) and 2% (w/w) agar gel (0.1 to 350 MPa) at 5 and 25 degrees C. Calibration results showed a good correlation with the reference data of pure water: R(2)= 0.966 for thermal conductivity and R(2)= 0.837 for diffusivity, and a small standard deviation of relative error (3.18%) for the volumetric heat capacity. Fresh potato and cheddar cheese were used as test samples at 5 degrees C at selected pressure levels (0.1 to 350 MPa). The potato samples gave thermal properties very close to those of pure water, but much higher than those of the cheese. The k and alpha values of both potato and cheese increased with pressure and a 2nd-order polynomial well fitted their pressure dependency. The volumetric heat capacity data did not show a clear pressure-dependency trend. The experimental system worked well for the evaluation of thermal properties at pressures up to 350 MPa.

  20. PREPARATION AND PROPERTIES OF COMPOUND ARNEBIAE RADIX MICROEMULSION GEL.

    Science.gov (United States)

    Chen, Jing; He, Yanping; Gao, Ting; Zhang, Licheng; Zhao, Yuna

    2017-01-01

    Compound Arnebiae radix oil has been clinically applied to treat burns and scalds for a long time. However, it is unstable and inconvenient to use. The aim of this study was to prepare a compound Arnebiae radix microemulsion gel for transdermal delivery system and evaluate its characteristics. Based on the solubility of Shikonin, the active component of Arnebiae radix and the results of phase studies, adequate ratio of each component in microemulsion was determined. The optimized microemulsion gel was prepared using Carbomer 940. The gels were characterized in terms of appearance, preliminary stability test and the content of Shikonin in the compound Arnebiae radix microemulsion gel with HPLC analysis. The optimized conditions for preparing microemulsion were Tween-80, glycerin, isopropyl myristate (IPM) with the ratio of 6:3:2. The optimal microemulsion gel was obtained with Carbomer 940 (1.0%). The prepared compound Arnebiae radix microemulsion gel showed good stability over time. It is more convenience in application than the previous used formulations.

  1. Refractive index contrast in porous silicon multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Nava, R.; Mora, M.B. de la; Tagueena-Martinez, J. [Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Temixco, Morelos (Mexico); Rio, J.A. del [Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Temixco, Morelos (Mexico); Centro Morelense de Innovacion y Transferencia Tecnologica, Consejo de Ciencia y Tecnologia del Estado de Morelos (Mexico)

    2009-07-15

    Two of the most important properties of a porous silicon multilayer for photonic applications are flat interfaces and a relative large refractive index contrast between layers in the optical wavelength range. In this work, we studied the effect of the current density and HF electrolyte concentration on the refractive index of porous silicon. With the purpose of increasing the refractive index contrast in a multilayer, the refractive index of porous silicon produced at low current was studied in detail. The current density applied to produce the low porosity layers was limited in order to keep the electrolyte flow through the multilayer structure and to avoid deformation of layer interfaces. We found that an electrolyte composed of hydrofluoric acid, ethanol and glycerin in a ratio of 3:7:1 gives a refractive index contrast around 1.3/2.8 at 600 nm. Several multilayer structures with this refractive index contrast were fabricated, such as dielectric Bragg mirrors and microcavities. Reflectance spectra of the structures show the photonic quality of porous silicon multilayers produced under these electrochemical conditions. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  2. Membrane-Based Separation of Phenol/Water Mixtures Using Ionically and Covalently Cross-Linked Ethylene-Methacrylic Acid Copolymers

    Directory of Open Access Journals (Sweden)

    Alexander Mixa

    2008-01-01

    Full Text Available Membrane-based separation of phenol/water mixtures with concentrations of phenol between 3 wt% and 8 wt% in the feed has been performed with nonmodified as well as cross-linked ethylene-methacrylic acid (E-MAA copolymers with different amounts of methacrylic acid. As cross-linking agents, aluminium acetyl acetonate, which leads to ionically cross-linked membranes, and 2,3,5,6-tetramethyl-1,4-phenylene diamine and glycerine digycidether, leading to covalently cross-linked membranes, have been used. Generally, it was found that with increasing phenol content in the feed, the total flux is increasing whereas the enrichment factor is decreasing. Using nonmodified membranes with higher methacrylic acid monomer content in the polymer, lower fluxes and higher enrichment factors were observed. Investigation of different cross-linked membranes showed that with high phenol concentration in the feed, ionic cross-linking seems to be very promising. Furthermore, variation of feed temperature shows that ionically cross-linked membranes reached higher fluxes as well as higher enrichment factors at elevated temperatures. The temperature-dependent data were fitted based on an Arrhenius-type equation, and activation energies for the permeation of phenol and water through the membrane were calculated.

  3. [Development and application of electroanalytical methods in biomedical fields].

    Science.gov (United States)

    Kusu, Fumiyo

    2015-01-01

    To summarize our electroanalytical research in the biomedical field over the past 43 years, this review describes studies on specular reflection measurement, redox potential determination, amperometric acid sensing, HPLC with electrochemical detection, and potential oscillation across a liquid membrane. The specular reflection method was used for clarifying the adsorption of neurotransmitters and their related drugs onto a gold electrode and the interaction between dental alloys and compound iodine glycerin. A voltammetric screening test using a redox potential for the antioxidative effect of flavonoids was proposed. Amperometric acid sensing based on the measurement of the reduction prepeak current of 2-methyl-1,4-naphthoquinone (VK3) or 3,5-di-tert-buty1-1,2-benzoquinone (DBBQ) was applied to determine acid values of fats and oils, titrable acidity of coffee, and enzyme activity of lipase, free fatty acids (FFAs) in serum, short-chain fatty acids in feces, etc. The electrode reactions of phenothiazines, catechins, and cholesterol were applied to biomedical analysis using HPLC with electrochemical detection. A three-channel electrochemical detection system was utilized for the sensitive determination of redox compounds in Chinese herbal medicines. The behavior of barbituric acid derivatives was examined based on potential oscillation measurements.

  4. Transdermal nicotine mixed natural rubber-hydroxypropylmethylcellulose film forming systems for smoking cessation: in vitro evaluations.

    Science.gov (United States)

    Pichayakorn, Wiwat; Suksaeree, Jirapornchai; Boonme, Prapaporn; Taweepreda, Wirach; Amnuaikit, Thanaporn; Ritthidej, Garnpimol C

    2014-08-27

    Abstract Novel film forming polymeric dispersions for transdermal nicotine delivery were prepared from deproteinized natural rubber latex (DNRL) blended with hydroxypropylmethylcellulose (HPMC) and dibutyl phthalate (DBP) or glycerin (GLY) as plasticizer. The preliminary molecular compatibility of ingredients was observed by Fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray diffractometry characterizations. All film forming polymeric dispersions were elegant in appearance and smooth in texture without agglomeration. Their pH was 7-8. In addition, their viscosity and spreadability showed good characteristics depended on HPMC and plasticizers blended. The transparent in situ dry films with good strength and elasticity were also confirmed by peeling-off. The nicotine release from them revealed an initial fast release that was similar to the release from a concentrated nicotine solution, and followed by slow release pattern from the in situ films. GLY blended formulation produced a higher amount of nicotine permeation through the in vitro pig skin than DBP blends. Ethanol mixing also enhanced nicotine permeation, but it affected the integrity of in situ films. The nicotine release and skin permeation kinetics were by a diffusion mechanism that was confirmed by the Higuchi's model. These formulations were safe without producing any severe skin irritation. However, for the stability they needed to be stored at 4 °C in tightly sealed containers.

  5. Successful laparoscopic repair of uterine and rectal prolapse in an infant

    Directory of Open Access Journals (Sweden)

    Mariko Yoshida

    2017-12-01

    Full Text Available Neonatal or infantile uterine prolapse is a quite rare condition and is usually managed with conservative treatment. There is no standard surgical treatment for infantile uterine prolapse, and to the best of our knowledge, only 2 out of 30 patients suffering from it have been reported to undergo surgical repair in English literature since 1961. We here report the first successful case of laparoscopic repair for uterine prolapse in an infant. The patient was a 2-month old girl who had sacral myelomeningocele and Chiari type 2 malformation. She had undergone closure of myelomeningocele and ventriculoperitoneal shunting within 6 weeks after birth. At 7 weeks of age, the rectum and the uterus prolapsed, and the prolapse gradually deteriorated. Conservative treatments including repeated digital reduction, use of ointment and glycerin enema, and placement of a Foley catheter into the vagina were not effective. At the age of 100 days, she underwent laparoscopic hysteropexy and rectopexy. Three ports were placed on the umbilicus and the bilateral abdomen, and the bilateral mesovaria were sutured to the anterior abdominal wall to improve the visualization of the pelvis. The rectum and the uterine body were directly sutured to the sacral promontory with 2 non-absorbable braided sutures each, not using mesh prosthesis. The postoperative course was uneventful and neither uterine nor rectal prolapse has recurred for 2.5 years. We plan to follow up the patient for a long period since the long-term prognosis is not known.

  6. Determination of Methane and Carbon Dioxide Formation Rate Constants for Semi-Continuously Fed Anaerobic Digesters

    Directory of Open Access Journals (Sweden)

    Jan Moestedt

    2015-01-01

    Full Text Available To optimize commercial-scale biogas production, it is important to evaluate the performance of each microbial step in the anaerobic process. Hydrolysis and methanogenesis are usually the rate-limiting steps during digestion of organic waste and by-products. By measuring biogas production and methane concentrations on-line in a semi-continuously fed reactor, gas kinetics can be evaluated. In this study, the rate constants of the fermentative hydrolysis step (kc and the methanogenesis step (km were determined and evaluated in a continuously stirred tank laboratory-scale reactor treating food and slaughterhouse waste and glycerin. A process additive containing Fe2+, Co2+ and Ni2+ was supplied until day 89, after which Ni2+ was omitted. The omission resulted in a rapid decline in the methanogenesis rate constant (km to 70% of the level observed when Ni2+ was present, while kc remained unaffected. This suggests that Ni2+ mainly affects the methanogenic rather than the hydrolytic microorganisms in the system. However, no effect was initially observed when using conventional process monitoring parameters such as biogas yield and volatile fatty acid concentration. Hence, formation rate constants can reveal additional information on process performance and km can be used as a complement to conventional process monitoring tools for semi-continuously fed anaerobic digesters.

  7. Bio-MTBE. A new option to fulfil biofuel quota for gasoline; Bio-MTBE. Eine neue Option zur Erfuellung der Biokraftstoffquote in Ottokraftstoffen

    Energy Technology Data Exchange (ETDEWEB)

    Busch, Oliver M.; Schade, Arnd; Locher, Annette [Evonik Industries AG, Essen (Germany)

    2013-05-15

    To meet the legally required bio-fuel quota in gasoline, an alternative to the ethanol blend E10 is nowavailable for nearly one year. Evonik Industries has introduced a bio-version of methyl tert-butyl ether (MTBE), an anti-knock agent, on the market. Chemically, both products are identical, because in production methanol is exchanged for bio-methanol. Bio-methanol is produced from raw glycerine, which arises as a byproduct from biodiesel production. This makes bio-MTBE an ideal bio-fuel component as defined by the EU's Renewable Energy Directive: Fuel components made from waste and residues are ''double counted'' regarding their bio-energy content. The product is widely used in the German and Dutch markets. In both countries, bio- MTBE is legally recognized as a bio-fuel component fulfilling double counting requirements. In the meantime, also other European countries have been introducing double counting for second-generation biofuel components. The EU Commission proposed to allow components based on residual materials to be calculated fourfold in the future. Should this be the case, bio-MTBE would become significantly more valuable. (orig.)

  8. Modern trends in the conservative management of lower jaw radio-necrosis following radiotherapy for tongue cancer

    International Nuclear Information System (INIS)

    Dapkova, L.

    1997-01-01

    This is a report on radio-necrosis of the lower jaw developing after radiation treatment for tongue cancer. Brief literature data concerning lower jaw osteoradionecrosis are presented, including incidence rate, dependence on the type of irradiation and doses applied and overall therapeutic approach to the lesion. An original scheme for complex conservative management, consistent with the specific pathogenetic patterns of post-irradiation necrosis, promoting active osteogenesis is proposed. It includes: antibiotics (4 quinolines, metronidazole, lincomycin, cephalosporin, nystatin), local antiseptic drugs (gargle with camomile, sol. tripaflavini 2 per cent, borax-glycerin, sterile 10 per cent solution of sodium chloride and the like), Miacalcic (calcitonin), vitamin D2, calcium-phospho C, parenteral nutrition, vitamins, retabolil, analgesics (general and local). The scheme, used in three patients with lower jaw radio-necrosis developing after radiotherapy for lingual cancer, yields very good results - pain relief, disappearance of trismus, with nutrition and sleep returning to normal. After demarcation of the necrotic tissue, sequestrectomy is done with ensuing complete epithelization. Lower jaw integrity is preserved without any functional and cosmetic defects. The duration of treatment is 8, 4 and 2 months, respectively (author)

  9. NRC Information Notice No. 93-25: Electrical penetration assembly degradation

    International Nuclear Information System (INIS)

    Grimes, B.K.

    1993-01-01

    In July 1987 and in October 1989, the licensee for the Trojan Nuclear Plant, the Portland and General Electric Company, reported problems with containment air leakage through its Bunker-Ramo electrical penetration assembly seals. In July and August 1991, the NRC inspected the use of containment electrical penetration assembly seals at Trojan and concluded that the licensee had not established an effective program for trending and evaluating electrical penetration assembly seal leakage. On October 28, 1991, while the plant was in a refueling outage, the licensee reported to the NRC that in the originally installed electrical penetration assemblies, the seal (polyurethane) and lubricant (Celvacen or Glycerin) materials were inappropriate for the application. The licensee concluded that these materials may cause seal degradation and that the seals may become degraded if subjected to design basis accident conditions for moisture or temperature. The licensee replaced the electrical penetration assembly seal with an environmentally qualified ethylene propylene rubber seal and added a silicone rubber backup O-ring to the outer face of each electrical penetration assembly module. The licensee subsequently replaced all the Bunker-Ramo electrical penetration assemblies with Conax assemblies

  10. Artifact suppression in electron paramagnetic resonance imaging of 14N- and 15N-labeled nitroxyl radicals with asymmetric absorption spectra

    Science.gov (United States)

    Takahashi, Wataru; Miyake, Yusuke; Hirata, Hiroshi

    2014-10-01

    This article describes an improved method for suppressing image artifacts in the visualization of 14N- and 15N-labeled nitroxyl radicals in a single image scan using electron paramagnetic resonance (EPR). The purpose of this work was to solve the problem of asymmetric EPR absorption spectra in spectral processing. A hybrid function of Gaussian and Lorentzian lineshapes was used to perform spectral line-fitting to successfully separate the two kinds of nitroxyl radicals. This approach can process the asymmetric EPR absorption spectra of the nitroxyl radicals being measured, and can suppress image artifacts due to spectral asymmetry. With this improved visualization method and a 750-MHz continuous-wave EPR imager, a temporal change in the distributions of a two-phase paraffin oil and water/glycerin solution system was visualized using lipophilic and hydrophilic nitroxyl radicals, i.e., 2-(14-carboxytetradecyl)-2-ethyl-4,4-dimethyl-3-oxazolidinyloxy (16-DOXYL stearic acid) and 4-hydroxyl-2,2,6,6-tetramethylpiperidine-d17-1-15N-1-oxyl (TEMPOL-d17-15N). The results of the two-phase separation experiment verified that reasonable artifact suppression could be achieved by the present method that deals with asymmetric absorption spectra in the EPR imaging of 14N- and 15N-labeled nitroxyl radicals.

  11. Integral process of obtaining glycerol as a by-product of biodiesel production from castor oil

    Directory of Open Access Journals (Sweden)

    Leonel Romero

    2012-12-01

    Full Text Available The biodiesel is obtained from about 10 years ago in Europe, and now that it has taken hold as fuel for diesel engines, it is expected a clear increase in the production of this class of fuels in a the near future. The biodiesel is derived from the transesterification reaction of castor oil with methanol, which is the main by-product the glycerol with an approximate content of 10%. Besides catalyst residuals, soaps, methanol traces, mono and diglycerides in small percentages are presented. This study proposes the separation, purification and characterization of the glycerol obtained from the transesterificación reaction of the castor oil, in order to be able to market it in the national or international market, so that it fulfills the standards of quality, which means getting a pure glycerol and the appropriate physico-chemical characteristics and techniques. The glycerin-methyl esters separation is carried out by decantation being obtained a percentage of around 70% glycerol. This percentage is subsequently increased through the purification process, using hydrochloric acid. Glycerol characterization was carried out by physicochemical and organoleptic tests. The purification process allowed us to obtain a glycerol with a percentage of purity close to 98%. It was also tested by comparison with theoretical data that remnants influenced in the physiochemical properties

  12. Effect of Different Diets of Flour Moth on its Parasitoid Wasp Fitness, Trichogramma brassicae (Hym.:Trichogrammatidae

    Directory of Open Access Journals (Sweden)

    Paria Soltaninejad

    2017-03-01

    Full Text Available Introduction: Parasitoid wasp, Trichogramma brassicae (Bezdenko (Hym.: Trichogrammatidae has excellent position in mass production technology, scope of application, wide geographical distribution and unmatched talent to adapt to different climatic conditions that can be easily reared on Mediterranean flour moth (MFM, Ephestia kuehniella Zeller (Lep.: Pyralidae. The parasitoid use is in order to control Chilo suppressalis (Walker (Lep.: Pyralidae, Helicoverpa armigera (Lep.: Noctuidae, Ostrinia nubilalis (Hübner (Lep.: Pyralidae, Ectomyelois ceratoniae (Zeller (Lep.: Phycitidae and Cydia pomonella (Lep.: Tortricidae (38. The studies have been shown that the quantity and quality of the host diet affect growth period, size of adults, adult longevity, fecundity and sex ratio of the parasitoid. The objective of current research was to evaluate the effect of four different MFM diets on the fitness of second and forth generations of the parasitoid wasp, T. brassicae. Materials and Methods: The four diets ((I wheat flour, wheat bran, corn flour, bread yeast and glycerin; (II wheat flour, wheat bran, barley flour, bread yeast and glycerin; (III barley flour, bread yeast and glycerin and (IV wheat flour, barley flour and corn flour were sterilized at 51 °C for 24 hours. After cooling at ambient temperature, the diets were contaminated with the eggs of MFM and then were maintained at 25±1° C, 60±5 % RH and a photoperiod of 14 L: 10 D. The MFM adults emerged after 35 to 40 days and their eggs were collected daily to use for investigation of the parasitoid biology. For rearing the parasitoid wasps on the MFM eggs obtained from each diet, some cards containing the parasitoid pre-pupae were put inside cages (25 × 25 × 25 cm and reared for one generation. The adults were fed honey (20% for one day and then were provided with one-day-old sterile MFM eggs. To prevent egg hatching and sterile them, they were kept at 15°C for four h. The tests were

  13. Quality control of the breast cancer treatments on Hdr brachytherapy with TLD-100

    Energy Technology Data Exchange (ETDEWEB)

    Torres H, F. [Universidad de Cordoba, Materials and Applied Physics Group, 230002 Monteria, Cordoba (Colombia); De la Espriella V, N. [Universidad de Cordoba, Grupo Avanzado de Materiales y Sistemas Complejos, 230002 Monteria, Cordoba (Colombia); Sanchez C, A., E-mail: franciscotorreshoyos@yahoo.com [Universidad de Cordoba, Departamento de Enfermeria, 230002 Monteria, Cordoba (Colombia)

    2014-07-01

    An anthropomorphic Phantom, a female trunk, was built with a natural bone structure and experimental material coated, glycerin and water-based material called JJT to build soft tissue equivalent to the muscle of human tissue, and a polymer (styrofoam) to build the lung as critical organ to simulate the treatment of breast cancer, with high dose rate brachytherapy (Hdr) and sources of Ir-192. The treatments were planned and calculated for the critical organ: Lung, and injury of 2 cm in diameter in breast with Micro Selectron Hdr system and the software Plato Brachytherapy V 14.1 of the Nucletron (Netherlands) which uses the standard protocol of radiotherapy for brachytherapy treatments. The dose experimentally measured with dosimeters TLD-100 LiF: Mg; Ti, which were previously calibrated, were placed in the same positions and bodies mentioned above, with less than 5% uncertainty. The reading dosimeters was carried out in a Harshaw TLD 4500. The results obtained for calculated treatments, using the standard simulator, and the experimental with TLD-100, show a high concordance, as they are on average a ± 1.1% making process becomes in a quality control of this type of treatments. (Author)

  14. Biodiesel's Characteristics Preparation from Palm Oil

    Directory of Open Access Journals (Sweden)

    Tilani Hamid

    2010-10-01

    Full Text Available Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio = 5 : 1, amount of NaOH used as catalyst = 3.5 gr, 4.5 gr, 5 gr and 5.5 gr and it takes about one hour time reaction. The ester (metil ester produced are separated from glycerin and washed until it takes normal pH (6-7 where more amount of catalyst used will decrease the ester (biodiesel produced. The results show that biodiesels' properties made by using 3.5 (M3.5 gr, 4.5 gr (M4.5 and 5 (M5.0 gr catalyst close to industrial diesel oil and the other (M5.5 closes to automotive diesel oil, while blending diesel oil with 20 % biodiesel (B20 is able to improve the diesel engine performances.

  15. Clinical evaluation of the role of tulsi and turmeric in the management of oral submucous fibrosis: A pilot, prospective observational study

    Directory of Open Access Journals (Sweden)

    Adit Srivastava

    2015-01-01

    Full Text Available The aim of the present study was to investigate the clinical efficacy of herbal medicines (1 gm tulsi and 1 gm turmeric mixed in glycerine base for the treatment of oral submucous fibrosis (OSMF. Forty-one patients in the age group of 17- 56 years without any systemic complications were included in the study. The patients were treated with medicines, which were to be applied 3-4 times a day. Blood samples were collected before and after treatment to screen for any systemic changes due to these medications. Burning sensation and mouth opening were recorded before and after treatment. Patients were followed up on monthly subsequent visits for three months. Changes in the burning sensation on visual analogue scale (VAS scale and difference in the mouth opening were analyzed statistically. A statistically significant improvement was seen in both burning sensation and mouth opening. Tulsi and turmeric offers a safe and efficacious combination of natural products available for symptomatic treatment of OSMF.

  16. Physically Transient Memory on a Rapidly Dissoluble Paper for Security Application

    Science.gov (United States)

    Bae, Hagyoul; Lee, Byung-Hyun; Lee, Dongil; Seol, Myeong-Lok; Kim, Daewon; Han, Jin-Woo; Kim, Choong-Ki; Jeon, Seung-Bae; Ahn, Daechul; Park, Sang-Jae; Park, Jun-Young; Choi, Yang-Kyu

    2016-12-01

    We report the transient memory device by means of a water soluble SSG (solid sodium with glycerine) paper. This material has a hydroscopic property hence it can be soluble in water. In terms of physical security of memory devices, prompt abrogation of a memory device which stored a large number of data is crucial when it is stolen because all of things have identified information in the memory device. By utilizing the SSG paper as a substrate, we fabricated a disposable resistive random access memory (RRAM) which has good data retention of longer than 106 seconds and cycling endurance of 300 cycles. This memory device is dissolved within 10 seconds thus it can never be recovered or replicated. By employing direct printing but not lithography technology to aim low cost and disposable applications, the memory capacity tends to be limited less than kilo-bits. However, unlike high memory capacity demand for consumer electronics, the proposed device is targeting for security applications. With this regards, the sub-kilobit memory capacity should find the applications such as one-time usable personal identification, authentication code storage, cryptography key, and smart delivery tag. This aspect is attractive for security and protection system against unauthorized accessibility.

  17. Mode of action of cupping--local metabolism and pain thresholds in neck pain patients and healthy subjects.

    Science.gov (United States)

    Emerich, M; Braeunig, M; Clement, H W; Lüdtke, R; Huber, R

    2014-02-01

    Cupping worldwide has been part of traditional medicine systems and is in the western world used as CAM therapy mainly for treating pain syndromes. The mode of action is up to now unclear. In order to investigate its mechanism we measured in parallel metabolic changes in the tissue under the cupping glass and pressure pain thresholds. In 12 volunteers (6 healthy subjects and 6 patients with chronic neck pain) a microdialysis system was implanted subcutaneously on both sides (left and right) above the trapezius muscle. After baseline measures cupping was performed at one randomly selected side (left or right), the other side served as control. Every 20 min during baseline measures and for 280 min after cupping, microdialysis probes for detection of lactate, pyruvate, glucose and glycerin were taken. In addition, pain thresholds were measured before and after cupping with algometry. Cupping resulted in a strong increase of lactate (beginning 160 min after cupping until the end of the measurements) and the lactate/pyruvate ratio, indicating an anaerobe metabolism in the surrounding tissue. Baseline pain thresholds were non-significantly lower in neck pain patients compared to healthy controls and slightly increased immediately after cupping (pcupping in healthy subjects and on the foot in neck pain patients). After 280 min no more significant changes of pain thresholds were detected. Cupping induces >280 min lasting anaerobe metabolism in the subcutaneous tissue and increases immediate pressure pain thresholds in some areas. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Influence of preservative and mounting media on the size and shape of monogenean sclerites.

    Science.gov (United States)

    Fankoua, Severin-Oscar; Bitja Nyom, Arnold R; Bahanak, Dieu Ne Dort; Bilong Bilong, Charles F; Pariselle, Antoine

    2017-08-01

    Based on Cichlidogyrus sp. (Monogenea, Ancyrocephalidae) specimens from Hemichromis sp. hosts, we tested the influence of different methods to fix/preserve samples/specimens [frozen material, alcohol or formalin preserved, museum process for fish preservation (fixed in formalin and preserved in alcohol)] and different media used to mount the slides [tap water, glycerin ammonium picrate (GAP), Hoyer's one (HM)] on the size/shape of sclerotized parts of monogenean specimens. The results show that the use of HM significantly increases the size of haptoral sclerites [marginal hooks I, II, IV, V, and VI; dorsal bar length, width, distance between auricles and auricle length, ventral bar length and width], and changes their shape [angle opening between shaft and guard (outer and inner roots) in both ventral and dorsal anchors, ventral bar much wider, dorsal one less curved]. This influence seems to be reduced when specimens/samples are fixed in formalin. The systematics of Monogenea being based on the size and shape of their sclerotized parts, to prevent misidentifications or description of invalid new species, we recommend the use of GAP as mounting medium; Hoyer's one should be restricted to monogenean specimens fixed for a long time which are more shrunken.

  19. Life cycle assessment of biofuels from an integrated Brazilian algae-sugarcane biorefinery

    International Nuclear Information System (INIS)

    Souza, Simone P.; Gopal, Anand R.; Seabra, Joaquim E.A.

    2015-01-01

    Sugarcane ethanol biorefineries in Brazil produce carbon dioxide, electricity and heat as byproducts. These are essential inputs for algae biodiesel production. In this paper, we assessed ethanol's life cycle greenhouse gas emissions and fossil energy use produced in an integrated sugarcane and algae biorefinery where biodiesel replaces petroleum diesel for all agricultural operations. Carbon dioxide from cane juice fermentation is used as the carbon source for algae cultivation, and sugarcane bagasse is the sole source of energy for the entire facility. Glycerin produced from the biodiesel plant is consumed by algae during the mixotrophic growth phase. We assessed the uncertainties through a detailed Monte-Carlo analysis. We found that this integrated system can improve both the life cycle greenhouse gas emissions and the fossil energy use of sugarcane ethanol by around 10% and 50%, respectively, compared to a traditional Brazilian sugarcane ethanol distillery. - Highlights: • A high diesel consumption is associated to the ethanol sugarcane life-cycle. • Sugarcane industry can provide sources of carbon and energy for the algae growing. • The sugarcane-algae integration can improve the ethanol life-cycle performance. • This integration is a promising pathway for the deployment of algae biodiesel. • There are still significant techno-economic barriers associated with algae biodiesel

  20. Victimless vapour? Health care organizations should restrict the use of e-cigarettes.

    Science.gov (United States)

    Bean, Sally T; Smith, Maxwell J

    2016-03-16

    Electronic cigarettes (e-cigarettes) are battery-powered devices that heat a liquid containing either vegetable glycerin or propylene glycol in combination with nicotine and/or flavours; an aerosol is produced that is inhaled by the user. Health Canada currently prohibits the importation, marketing or selling of e-cigarettes containing nicotine, although they can be easily purchased. Because of the availability of e-cigarettes, patients and visitors to health care organizations (HCOs) are inquiring about their use within and on the grounds of those facilities. We contend that in provinces or municipalities where e-cigarette use has not been restricted, HCOs should develop institutional policies to do so. We argue that the following reasons collectively justify measures to restrict the use of e-cigarettes within HCOs: unknown long-term safety, uncertain effectiveness in harm reduction, the conflict with the mission of HCOs to promote health, the potential negative health impacts on vulnerable patients with a compromised health status, and the risk of re-normalization of smoking. However, because of the rapidly developing evidence base in this area, HCOs should remain responsive to emerging evidence regarding the status of e-cigarettes as an effective harm reduction tool.

  1. Optimization of experimental conditions for composite biodiesel production from transesterification of mixed oils of Jatropha and Pongamia

    Energy Technology Data Exchange (ETDEWEB)

    Yogish, H.; Chandrashekara, K.; Pramod Kumar, M.R. [S.J. College of Engineering, Department of Mechanical Engineering, Mysore (India)

    2012-11-15

    India is looking at the renewable alternative sources of energy to reduce its dependence on import of crude oil. As India imports 70 % of the crude oil, the country has been greatly affected by increasing cost and uncertainty. Biodiesel fuel derived by the two step acid transesterification of mixed non-edible oils from Jatropha curcas and Pongamia (karanja) can meet the requirements of diesel fuel in the coming years. In the present study, different proportions of Methanol, Sodium hydroxide, variation of Reaction time, Sulfuric acid and Reaction Temperature were adopted in order to optimize the experimental conditions for maximum biodiesel yield. The preliminary studies revealed that biodiesel yield varied widely in the range of 75-95 % using the laboratory scale reactor. The average yield of 95 % was obtained. The fuel and chemical properties of biodiesel, namely kinematic viscosity, specific gravity, density, flash point, fire point, calorific value, pH, acid value, iodine value, sulfur content, water content, glycerin content and sulfated ash values were found to be within the limits suggested by Bureau of Indian Standards (BIS 15607: 2005). The optimum combination of Methanol, Sodium hydroxide, Sulfuric acid, Reaction Time and Reaction Temperature are established. (orig.)

  2. Preliminary measurement of the drag force on a porous cylinder with fluid evolution under conditions relevant to pulverised-fuel combustion

    Energy Technology Data Exchange (ETDEWEB)

    Dijan Supramono; Graham J. Nathan; Peter J. Ashman; Peter J. Mullinger [University of Adelaide, Adelaide, SA (Australia). Cooperative Research Centre for Clean Power from Lignite, Schools of Chemical Engineering and Mechanical Engineering

    2003-07-01

    The trajectories of the particles in pulverised coal combustion systems determine their residence times and reaction environments, and hence coal burnout and flame length. The trajectories, in turn, depend upon the drag coefficient of the particle. The effect of the evolution of fluid from the surface of the particle on this coefficient has never been measured before, particularly at the low particle Reynolds numbers that apply during coal combustion. Therefore mathematical models must rely on assumed sphere drag coefficients, which do not account for the effect of fluid evolving from the surface. A technique of using a porous cylinder mounted on a pendulum, instead of a sphere, through which fluid can be forced to evolve, simulating fluid evolution in coal devolatilisation and char burning, is used. The pendulum is capable of measuring drag forces of the order of 10-5 to 10-6 Newton, at Reynolds numbers similar to that experienced by coal particles. This paper presents preliminary measurements of drag force at relevant conditions. The working fluid is water in the first instance, although it will be extended to diluted glycerine in the future. The cross flow is provided by a water tunnel and the ejected fluid is induced by a separate pump. Both the Reynolds number and the ratio of evolution velocity to free-stream velocity are chosen to span conditions relevant to pulverised coal combustion. 16 refs., 5 figs., 2 tabs.

  3. Obtención y caracterización de un polímero biodegradable a partir del almidón de yuca Obtención y caracterización de un polímero biodegradable a partir del almidón de yuca

    Directory of Open Access Journals (Sweden)

    Gladys Ruiz Avilés

    2006-12-01

    Full Text Available En esta investigación se obtiene un polímero biodegradable a partir del almidón de yuca al procesar mezclas de almidón modificado con glicerina y agua como plastificantes, utilizando un molino abierto y una extrusora de monohusillo. Las variables a controlar durante la extrusión son: perfil de temperatura, torque, y velocidad de rotación del husillo. Se evalúan características mecánicas y fisicoquímicas mediante ensayos de tensión, análisis térmicos de Calorimetría Diferencial de Barrido (DSC y Análisis Termogravimétrico (TGA, Análisis Infrarrojo por Transformadas de Fourier (FTIR y morfología.This study focuses on the preparation of tapioca starch biodegradable polymer,processed by blends of starch modified with glycerine and water as plasticizers, by using roll mill and a single–screw extruder in the process. During extrusion, there is a series of variables to control namely: the barrel temperature profile, screw torque and screw rotation speed. Tensile test, Differential Scanning Calorimetric (DSC, Thermogravimetric Analysis (TGA, Fourier Transformer Infrared Spectroscopy (FTIR and morphology were used in the process.

  4. Enhancement of Fenton oxidation for removing organic matter from hypersaline solution by accelerating ferric system with hydroxylamine hydrochloride and benzoquinone.

    Science.gov (United States)

    Peng, Siwei; Zhang, Weijun; He, Jie; Yang, Xiaofang; Wang, Dongsheng; Zeng, Guisheng

    2016-03-01

    Fenton oxidation is generally inhibited in the presence of a high concentration of chloride ions. This study investigated the feasibility of using benzoquinone (BQ) and hydroxylamine hydrochloride (HA) as Fenton enhancers for the removal of glycerin from saline water under ambient temperature by accelerating the ferric system. It was found that organics removal was not obviously affected by chloride ions of low concentration (less than 0.1mol/L), while the mineralization rate was strongly inhibited in the presence of a large amount of chloride ions. In addition, ferric hydrolysis-precipitation was significantly alleviated in the presence of HA and BQ, and HA was more effective in reducing ferric ions into ferrous ions than HA, while the H2O2 decomposition rate was higher in the BQ-Fenton system. Electron spin resonance analysis revealed that OH production was reduced in high salinity conditions, while it was enhanced after the addition of HA and BQ (especially HA). This study provided a possible solution to control and alleviate the inhibitory effect of chloride ions on the Fenton process for organics removal. Copyright © 2015. Published by Elsevier B.V.

  5. Pharmacological Inhibition of Macrophage Toll-like Receptor 4/Nuclear Factor-kappa B Alleviates Rhabdomyolysis-induced Acute Kidney Injury.

    Science.gov (United States)

    Huang, Rong-Shuang; Zhou, Jiao-Jiao; Feng, Yu-Ying; Shi, Min; Guo, Fan; Gou, Shen-Ju; Salerno, Stephen; Ma, Liang; Fu, Ping

    2017-09-20

    Acute kidney injury (AKI) is the most common and life-threatening systemic complication of rhabdomyolysis. Inflammation plays an important role in the development of rhabdomyolysis-induced AKI. This study aimed to investigate the kidney model of AKI caused by rhabdomyolysis to verify the role of macrophage Toll-like receptor 4/nuclear factor-kappa B (TLR4/NF-κB) signaling pathway. C57BL/6 mice were injected with a 50% glycerin solution at bilateral back limbs to induce rhabdomyolysis, and CLI-095 or pyrrolidine dithiocarbamate (PDTC) was intraperitoneally injected at 0.5 h before molding. Serum creatinine levels, creatine kinase, the expression of tumor necrosis factor (TNF)-α, interleukin (IL)-1β and IL-6, and hematoxylin and eosin stainings of kidney tissues were tested. The infiltration of macrophage, mRNA levels, and protein expression of TLR4 and NF-κB were investigated by immunofluorescence double-staining techniques, reverse transcriptase-quantitative polymerase chain reaction, and Western blotting, respectively. In vitro, macrophage RAW264.7 was stimulated by ferrous myoglobin; the cytokines, TLR4 and NF-κB expressions were also detected. In an in vivo study, using CLI-095 or PDTC to block TLR4/NF-κB, functional and histologic results showed that the inhibition of TLR4 or NF-κB alleviated glycerol-induced renal damages (P rhabdomyolysis-induced AKI by the regulation of proinflammatory cytokine production and macrophage infiltration.

  6. A Simple and Fast Method for the Production and Characterization of Methylic and Ethylic Biodiesels from Tucum Oil via an Alkaline Route

    Directory of Open Access Journals (Sweden)

    Marcelo Firmino de Oliveira

    2011-01-01

    Full Text Available A simple, fast, and complete route for the production of methylic and ethylic biodiesel from tucum oil is described. Aliquots of the oil obtained directly from pressed tucum (pulp and almonds were treated with potassium methoxide or ethoxide at 40°C for 40 min. The biodiesel form was removed from the reactor and washed with 0.1 M HCl aqueous solution. A simple distillation at 100°C was carried out in order to remove water and alcohol species from the biodiesel. The oxidative stability index was obtained for the tucum oil as well as the methylic and ethylic biodiesel at 6.13, 2.90, and 2.80 h, for storage times higher than 8 days. Quality control of the original oil and of the methylic and ethylic biodiesels, such as the amount of glycerin produced during the transesterification process, was accomplished by the TLC, GC-MS, and FT-IR techniques. The results obtained in this study indicate a potential biofuel production by simple treatment of tucum, an important Amazonian fruit.

  7. A modular projection autostereoscopic system for stereo cinema

    Science.gov (United States)

    Elkhov, Victor A.; Kondratiev, Nikolai V.; Ovechkis, Yuri N.; Pautova, Larisa V.

    2009-02-01

    The lenticular raster system for 3D movies non-glasses show designed by NIKFI demonstrated commercially in Moscow in the 40'st of the last century. Essential lack of this method was narrow individual viewing zone as only two images on the film used. To solve this problem, we propose to use digital video projective system with modular principle of its design. Increase of the general number of the pixels forming the stereo image is reached by using of more than one projector. The modular projection autostereoscopic system for demonstration of the 3D movies includes diffuser screen; lenticular plate located in front of the screen; projective system consisted from several projectors and the block of parallax panoramogram fragments creator. By means of this block the parallax panoramogram is broken into fragments which quantity corresponds to number of projectors. For the large dimension lenticular screen making rectangular fragments of inclined raster were joined in a uniform leaf. To obtain the needed focal distance of the screen lenses we used immersion - aqueous solution of glycerin. The immersion also let essentially decrease visibility of fragments joints. An experimental prototype of the modular projection autostereoscopic system was created to validate proposed system.

  8. Natural convection flow and heat transfer between a fluid layer and a porous layer inside a rectangular enclosure

    International Nuclear Information System (INIS)

    Beckermann, C.; Ramadhyani, S.; Viskanta, R.

    1986-01-01

    A numerical and experimental study is performed to analyze the steady-state natural convection fluid flow and heat transfer in a vertical rectangular enclosure that is partially filled with a vertical layer of a fluid-saturated porous medium. The flow in the porous layer is modeled utilizing the Brinkman-Forchheimer-extended Darcy equations. The numerical model is verified by conducting a number of experiments with spherical glass beads as the porous medium and water and glycerin as the fluids in rectangular test-cells. The agreement between the flow visualization results and temperature measurements and the numerical model is, in general, good. It is found that the amount of fluid penetrating from the fluid region into the porous layer depends strongly on the Darcy (Da) and Rayleigh (Ra) numbers. For a relatively low product of Ra x Da, the flow takes place primarily in the fluid layer, and heat transfer in the porous layer is by conduction only. On the other hand, fluid penetrating into a relatively highly permeable porous layer has a significant impact on the natural convection flow patterns in the entire enclosure

  9. Allergenic Ingredients in Personal Hygiene Wet Wipes.

    Science.gov (United States)

    Aschenbeck, Kelly A; Warshaw, Erin M

    Wet wipes are a significant allergen source for anogenital allergic contact dermatitis. The aim of the study was to calculate the frequency of potentially allergenic ingredients in personal hygiene wet wipes. Ingredient lists from brand name and generic personal hygiene wet wipes from 4 large retailers were compiled. In the 54 personal hygiene wet wipes evaluated, a total of 132 ingredients were identified (average of 11.9 ingredients per wipe). The most common ingredients were Aloe barbadensis (77.8%), citric acid (77.8%), fragrance (72.2%), sorbic acid derivatives (63.0%), tocopherol derivatives (63.0%), glycerin (59.3%), phenoxyethanol (55.6%), disodium cocoamphodiacetate (53.7%), disodium ethylenediaminetetraacetic acid (EDTA) (42.6%), propylene glycol (42.6%), iodopropynyl butylcarbamate (40.7%), chamomile extracts (38.9%), sodium benzoate (35.2%), bronopol (22.2%), sodium citrate (22.2%), lanolin derivatives (20.4%), parabens (20.4%), polyethylene glycol derivatives (18.5%), disodium phosphate (16.7%), dimethylol dimethyl hydantoin (DMDM) (14.8%), and cocamidopropyl propylene glycol (PG)-dimonium chloride phosphate (11.1%). Of note, methylisothiazolinone (5.6%) was uncommon; methylchloroisothiazolinone was not identified in the personal hygiene wet wipes examined. There are many potential allergens in personal hygiene wet wipes, especially fragrance and preservatives.

  10. Phagocytosis and Inflammation: Exploring the effects of the components of E-cigarette vapor on macrophages.

    Science.gov (United States)

    Ween, Miranda P; Whittall, Jonathan J; Hamon, Rhys; Reynolds, Paul N; Hodge, Sandra J

    2017-08-01

    E-cigarettes are perceived as harmless; however, evidence of their safety is lacking. New data suggests E-cigarettes discharge a range of compounds capable of physiological damage to users. We previously established that cigarette smoke caused defective alveolar macrophage phagocytosis. The present study compared the effect E-cigarette of components; E-liquid flavors, nicotine, vegetable glycerine, and propylene glycol on phagocytosis, proinflammatory cytokine secretion, and phagocytic recognition molecule expression using differentiated THP-1 macrophages. Similar to CSE, phagocytosis of NTHi bacteria was significantly decreased by E-liquid flavoring (11.65-15.75%) versus control (27.01%). Nicotine also decreased phagocytosis (15.26%). E-liquid, nicotine, and E-liquid+ nicotine reduced phagocytic recognition molecules; SR-A1 and TLR-2. IL-8 secretion increased with flavor and nicotine, while TNF α , IL-1 β , IL-6, MIP-1 α , MIP-1 β , and MCP-1 decreased after exposure to most flavors and nicotine. PG, VG, or PG:VG mix also induced a decrease in MIP-1 α and MIP-1 β We conclude that E-cigarettes can cause macrophage phagocytic dysfunction, expression of phagocytic recognition receptors and cytokine secretion pathways. As such, E-cigarettes should be treated with caution by users, especially those who are nonsmokers. © 2017 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of The Physiological Society and the American Physiological Society.

  11. Stability evaluation of house dust mite vaccines for sublingual immunotherapy

    Directory of Open Access Journals (Sweden)

    MARIJA GAVROVIĆ-JANKULOVIĆ

    2010-01-01

    Full Text Available Allergen-specific immunotherapy with house dust mite (HDM allergen extracts can effectively alleviate the symptoms of allergic rhinitis and asthma. The efficacy of the immunotherapeutic treatment is highly dependent on the quality of house dust mite vaccines. This study was performed to assess the stability of house dust mite allergen vaccines prepared for sublingual immunotherapy. Lyophilized Dermatophagoides pteronyssinus (Dpt mite bodies were the starting material for the production of sublingual vaccines in four therapeutic concentrations. The stability of the extract for vaccine production, which was stored below 4 °C for one month, showed consistence in the protein profile in SDS PAGE. ELISA-inhibition showed that the potencies of Dpt vaccines during a 12 month period were to 65–80 % preserved at all analyzed therapeutic concentrations. This study showed that glycerinated Dpt vaccines stored at 4 °C preserved their IgE-binding potential during a 12 month period, implying their suitability for sublingual immunotherapeutic treatment of HDM allergy.

  12. Experimental analysis of minimum shear stress to drag particles in a horizontal bed; Analise experimental da tensao de cisalhamento minima para arraste de particulas em um leito horizontal

    Energy Technology Data Exchange (ETDEWEB)

    Dornelas, Breno Almeida; Soares, Edson Jose [Universidade Federal do Espirito Santo. Departamento de Engenharia Mecanica (Brazil)], e-mails: bad@ucl.br, edson@ct.ufes.br; Quirino Filho, Joao Pedro; Loureiro, Bruno Venturini [Faculdade do Centro Leste (UCL). Laboratorio de Fluidos e Fenomenos de Transporte (Brazil)], e-mails: joaoquirino@ucl.br, brunovl@ucl.br

    2009-12-15

    Efficient hole cleaning is still a challenge in well bore drilling to produce oil and gas. The critical point is the horizontal drilling that inherently tends to form a bed of sediment particles at the well bottom during drilling. The cuttings bed erosion depends mainly on the shear stress promoted by the drilling fluid flow. The shear stress required to cause drag in the cuttings bed is investigated according to the fluid and particles properties, using an experimental assembly, composed of: a system for fluid circulation, a particle box, a pump system and measuring equipment. The observation area is a box below the flow line in an acrylic duct used to calibrate sand particles. The test starts with the pumps in a low frequency which is increased in steps. At each frequency level, images are captured of carried particles and the established flow rate is recorded. The images are analyzed when the dragged particle is no longer random and sporadic, but becomes permanent. The shear stress is identified by the PKN correlation (by Prandtl, von Karman, and Nikuradse) for the minimum flow rate necessary to cause drag. Results were obtained for just water and water-glycerin solution flows. (author)

  13. A Membrane Process for Recycling Die Lube from Wastewater Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Eric S. Peterson; Jessica Trudeau; Bill Cleary; Michael Hackett; William A. Greene

    2003-04-01

    An active-surface membrane technology was used to separate a die lube manufacturing wastewater stream consisting of various oils, hydrocarbons, heavy metals, and silicones. The ultrafiltration membranes reduced organics from initial oil and grease contents by 20–25X, carbon oxygen demand (COD) by 1.5 to 2X, and total organic carbon (TOC) by 0.6, while the biological oxygen demand (BOD) remained constant. The active-surface membranes were not fouled as badly as non-active-surface systems and the active-surface membrane flux levels were consistently higher and more stable than those of the non-active-surface membranes tested. Field testing demonstrated that the rotary microfilter can concentrate the die lube, i.e. remove the glycerin component, and produce a die lube suitable for recycling. The recycling system operated for six weeks with only seven cleaning cycles and no mechanical or electrical failures. Test data and quality records indicate that the die casting scrap was reduced from 8.4 to 7.8%. There is no doubt that this test yielded tremendous results. This separation process presents significant opportunities that can be evaluated further.

  14. A Membrane Process for Recycling Die Lube from Wastewater Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, E. S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Trudeau, J. [Metaldyne, Inc., Twinsburg, OH (United States); Cleary, B. [Metaldyne, Inc., Twinsburg, OH (United States); Hackett, M. [Metaldyne, Inc., Twinsburg, OH (United States); Greene, W. A. [SpinTek FIltrations, LLC, Los Alamitos, CA (United States)

    2003-04-30

    An active-surface membrane technology was used to separate a die lube manufacturing wastewater stream consisting of various oils, hydrocarbons, heavy metals, and silicones. The ultrafiltration membranes reduced organics from initial oil and grease contents by 20-25X, carbon oxygen demand (COD) by 1.5 to 2X, and total organic carbon (TOC) by 0.6, while the biological oxygen demand (BOD) remained constant. The active-surface membranes were not fouled as badly as non-active-surface systems and the active-surface membrane flux levels were consistently higher and more stable than those of the non-active-surface membranes tested. Field testing demonstrated that the rotary microfilter can concentrate the die lube, i.e. remove the glycerin component, and produce a die lube suitable for recycling. The recycling system operated for six weeks with only seven cleaning cycles and no mechanical or electrical failures. Test data and quality records indicate that the die casting scrap was reduced from 8.4 to 7.8%. There is no doubt that this test yielded tremendous results. This separation process presents significant opportunities that can be evaluated further.

  15. Do electronic cigarettes impart a lower potential disease burden than conventional tobacco cigarettes? Review on E-cigarette vapor versus tobacco smoke.

    Science.gov (United States)

    Oh, Anne Y; Kacker, Ashutosh

    2014-12-01

    Development and utilization of electronic cigarettes (ECs) resulted from the search for healthier alternatives to conventional tobacco cigarettes (TCs) and the search for alternative methods for quitting TCs. This review compares the potential disease burden presented by TC smoke to that of EC vapor. Potential disease burden of EC vapor versus TC smoke was assessed by reviewing clinical studies that measured inhaled components. Chemicals and carcinogens produced by vapor versus smoke were compared. Studies show that EC vapors contain far less carcinogenic particles than TC smoke. Whereas ECs have the ability to reach peak serum cotinine/nicotine levels comparable to that of TCs, ECs do not cause an increase in total white blood cell count; thus, ECs have the potential to lower the risk of atherosclerosis and systemic inflammation. Use of ECs has been shown to improve indoor air quality in a home exposed to TC smoke. This reduces secondhand smoke exposure, thus having the potential to decrease respiratory illness/asthma, middle-ear disease, sudden infant death syndrome, and more. However, some studies claim that propylene glycol (PG) vapor can induce respiratory irritation and increase chances for asthma. To minimize risks, EC manufacturers are replacing PG with distilled water and glycerin for vapor production. Based on the comparison of the chemical analysis of EC and TC carcinogenic profiles and association with health-indicating parameters, ECs impart a lower potential disease burden than conventional TCs. © 2014 The American Laryngological, Rhinological and Otological Society, Inc.

  16. Frontal Cortex Transcriptome Analysis of Mice Exposed to Electronic Cigarettes During Early Life Stages.

    Science.gov (United States)

    Lauterstein, Dana E; Tijerina, Pamella B; Corbett, Kevin; Akgol Oksuz, Betul; Shen, Steven S; Gordon, Terry; Klein, Catherine B; Zelikoff, Judith T

    2016-04-12

    Electronic cigarettes (e-cigarettes), battery-powered devices containing nicotine, glycerin, propylene glycol, flavorings, and other substances, are increasing in popularity. They pose a potential threat to the developing brain, as nicotine is a known neurotoxicant. We hypothesized that exposure to e-cigarettes during early life stages induce changes in central nervous system (CNS) transcriptome associated with adverse neurobiological outcomes and long-term disease states. To test the hypothesis, pregnant C57BL/6 mice were exposed daily (via whole body inhalation) throughout gestation (3 h/day; 5 days/week) to aerosols produced from e-cigarettes either with nicotine (13-16 mg/mL) or without nicotine; following birth, pups and dams were exposed together to e-cigarette aerosols throughout lactation beginning at postnatal day (PND) 4-6 and using the same exposure conditions employed during gestational exposure. Following exposure, frontal cortex recovered from ~one-month-old male and female offspring were excised and analyzed for gene expression by RNA Sequencing (RNA-Seq). Comparisons between the treatment groups revealed that e-cigarette constituents other than nicotine might be partly responsible for the observed biological effects. Transcriptome alterations in both offspring sexes and treatment groups were all significantly associated with downstream adverse neurobiological outcomes. Results from this study demonstrate that e-cigarette exposure during early life alters CNS development potentially leading to chronic neuropathology.

  17. A survey of gastrointestinal helminth of stray dogs in Zabol city, southeastern of Iran

    Directory of Open Access Journals (Sweden)

    Geraili, A.

    2016-03-01

    Full Text Available Canids are reservoir for some zoonoses helminthic disease. They are one of main public health problem. The aim of this study was to ascertain frequency of gastrointestinal helminthic infection of stray dogs in Zabol city, southeaster of Iran. In this descriptive study, 30 stray dogs were euthanized, intestine was removed by necropsy. Then, the intestines was opened by scalpel and their contents passed through mesh sieve. The helminth were collected. The nematodes were preserved in 70% ethanol with 5% glycerin and cestodes were preserved in 70% ethanol. The cestodes were stained by acetocarmine. The nematodes were cleared by lactophenol. The genus and species of helminth were identified by identification keys. Twenty two (73.3% of stray dogs had at least one intestinal helminthic infection. Recovered helminth from stray dogs include: Taenia hydatigena (53.3%, Taenia ovis (20%, Taenia multiceps (6.6%, Mesocestoides spp (10%, Toxocara canis (23.3%, Toxocara cati (3.3%. Data showed that the stray dogs in Zabol city harbor some important zoonoses helminth parasite like Toxocara.

  18. The effect of clay nanoparticles as reinforcement on mechanical properties of bioplastic base on cassava starch

    Science.gov (United States)

    Harunsyah; Sariadi; Raudah

    2018-01-01

    Plastics have been used widely for packaging material since long time ago. However, environmentally friendly plastics or plastics whose raw materials come from natural polymers are still very low in development. Efforts have been conducted to develop environmental friendly plastic from renewable resources such as biopolymer. The aim of this paper is to study the influence of clay nanoparticles as reinforcment on the mechanical properties of bioplastic were prepared by solution-casting method. The content of clay nanoparticles in the bioplastic was varied from 0.2%, 0.4%, 0.6%, 0.8% and 1.0% (w/w) by weight of starch. Structural characterization was done by Fourier Transform Infrared Spectroscopy. Surface morphologies of the plastic film were examined by scanning electron microscope.The result showed that the Tensile strength was improved significantly with the addition of clay nanoparticles. The maximum tensile strength obtained was 24.18 M.Pa on the additional of clay nanoparticles by 0.6% and plasticizer by 25%. Based on data of FTIR, the produced bioplastic did not change the group function and it can be concluded that the interaction in bioplastic produced was only a physical interaction. The bioplastic based on cassava starch-clay nanoparticles and plasticizer glycerin showed that interesting mechanical properties being transparent, clear, homogeneous, flexible and easy to be handled.

  19. FORMULASI PASTA GIGI INFUSA DAUN JAMBU BIJI (Psidium guajavaLinn. DENGAN VARIASI KONSENTRASI Na. CMC SEBAGAI BAHAN PENGIKAT

    Directory of Open Access Journals (Sweden)

    Nur Sa’adah Daud

    2016-03-01

    Full Text Available Guava leaves (Psidium guajava Linn. has been shown inhibiting effect against dental caries causing bacteria such as Staphylococcus aureus and Streptococcus mutans. In order to facilitate its activity in overcoming dental caries,formulation into dosage toothpaste was needed. The purpose of this study was to formulate toothpaste from infuse of guava leaves with variations concentration of Sodium Carboxymethylcellulosa as a binder to obtain the best toothpaste formula. The concentration of infuse of guava leaves was 5% and 4%, 6% and 8%for Sodium carbxymethylcellulose respectively for formula each formula. Other additives have been used, they were calcium carbonate, glycerin, sodium lauryl sulfate, α-tocopherol, propyl paraben, methyl paraben, Oleum Menthae Piperatae (OMP and distilled water.The results showed that three toothpaste formula from the organoleptic testwere white coloured, mint flavored with soft and lumpy of textur, with the mean of pH value of 6,9 to 8,3 were eligible, and the foam height value of 3,5 to 5,5 cm. Theviscosity values were increased with the increasing concentration ofSodium carbxymethylcellulose. While the preference test showedthat toothpaste formula C was the most preferred.

  20. Sterilization of Bacillus spores by converted X-rays

    International Nuclear Information System (INIS)

    Ito, Hitoshi; Ohki, Yumi; Watanabe, Yuhei; Sunaga, Hiromi; Ishigaki, Isao

    1991-01-01

    Relative sensitivities of endospores of Bacillus pumilus E601, B. subtilis IAM1069, B. megaterium S31 and B. brevis S5 to gamma-rays, converted X-rays (Bremsstrahlung), and electron beams were examined in order to estimate the conditions in which converted X-rays kill Bacillus spores. The radiation sensitivities to gamma-rays, X-rays and electron beams of each strain dried on glass fiber filter without additives were found to be almost equivalent, and D 10 values were obtained as follows: 1.5-1.6 kGy for B. pumilus, 1.4-1.5 kGy for B. subtilis, 1.9-2.0 kGy for B. megaterium, and 1.6-2.0 kGy for B. brevis. The radiation sensitivities of endospores of each strain to electron beams were slightly lower than those to gamma-rays in the dry condition with additives of 2% peptone + 1% glycerin on glass fiber filter. The increase of radiation resistance in the presence of additives was also observed with X-rays, and it was on an intermediate level between those with gamma-rays and electron beams. In the dry condition using cellulose filter paper, only the radiation resistances of B. megaterium and B. brevis in the presence of additives were increased. (author)

  1. FORMULASI MIKROEMULSI EKSTRAK TERPURIFIKASI DAUN BAYAM MERAH (Amaranthus tricolor L. SEBAGAI SUPLEMEN ANTIOKSIDAN

    Directory of Open Access Journals (Sweden)

    Dwi Lestari Handayani

    2017-03-01

    Full Text Available A research has conducted about the microemulsion formulation of purified extract of red spinach leaves (Amaranthus tricolor L. as an antioxidant supplement with the aim to be able to know the formula to form a microemulsion which meet the physical quality stability and determine antioxidant activity (IC50 of the preparation. Extracts prepared by maceration method using ethanol 96% and then later do the purification using solvent n-hexane and ethyl acetate, after it tested its antioxidant activity. Formula to form a microemulsion purified extract of red spinach leaves clear is to use virgin coconut oil (VCO by 15%, tween 80 for 40%, 35% glycerin and 10% distilled water. Physical stability test was conducted on the organoleptic test, measuring the diameter of globules, pH test, test and test viscosity centrifugation. Test of antioxidant activity in vitro using DPPH method and using Vitamin C as a positive control. Measurement data were statistically analyzed using paired samples T test. The test results of antioxidant activity microemulsion purified extracts of spinach leaves, red show IC50 values on day 1 was 1.83 ppm and the 28th day amounted to 3.71 ppm. While vitamin C microemulsion shows IC50 values on day 1 of 0.24 ppm and the 28th day of 2.51 ppm. Despite the decreased antioxidant activity, but each of the stocks included in the category of very powerful antioxidants.

  2. Microemulsion Formulation of Combination of Virgin Coconut Oil and Rice Bran Oil for Hair Growth

    Directory of Open Access Journals (Sweden)

    Wira Noviana Suhery

    2018-04-01

    Full Text Available Research on micro emulsion formulation of combination of virgin coconut oil (VCO and rice bran oil (RBO as a hair growth promoter has been done. The purpose of this study was to formulate and produce the best formula that is physically stable and optimally promoting the hair growth by varying the content of VCO and RBO in the form of micro emulsions. These dosage formulations were prepared in three formulas using 45% tween 80 as surfactants and 20% glycerin as co surfactant i.e.: F,I containing a combination of VCO and RBO 1:1; FII (1:2 and FIII (2:1. Physical evaluation of the preparation was carried out for 8 weeks of storage which included organoleptic examination, pH, homogeneity, density, globule particle size, phase freeze thaw, and rabbit hair growth activity test for 18 days. Based on the results of the evaluation, it was found that the FI, FII and FIII micro emulsion formulations were physically stable for 8 weeks of storage with a pH ranging from 6.7 to 7.0, density of 1.085-1.088 g/mL, average globul particle size of FI (34.6 nm , FII (54 nm and FIII (68.8 nm. The best formulas is FIII for hair growth length of 1.26 cm for 18 days.

  3. Study of the Transformation of the Oil of Used Soya in Fatty Acid Ethyl Ester

    Directory of Open Access Journals (Sweden)

    Anabel Sarracent-López

    2016-07-01

    Full Text Available The reuse of vegetable oils in food processing brings harmful health effects and on the other hand needs a complex treatment to discard without affecting the environment. Transformed into methyl or ethyl esters of fatty acids and glycerin by transesterification with the corresponding alcohol, can be a suitable method for treatment. It was investigated residual soybean oil from a producer of fried foods and ethanol. It is known that with this spirit the transformation process presents difficulties not listed with methanol, but at the same time does not bring the drawbacks of the latter, for toxicity and acquisition, and that since it is a derivative of the domestic sugar industry does not constitute a raw material import. We experimented with ethanol 80 %, 85 % and 90 % purity and worked 35 ºC and 50 ºC. Final yields of ethyl esters, are low compared with those obtained for similar processes with methanol, 85 % being the highest yield obtained under the conditions of the process. An assessment of costs was conducted to produce 1L of ethyl esters in the laboratory, the expenses of 0,56 pesos/L.

  4. Extraction of Oleic Acid from Moroccan Olive Mill Wastewater.

    Science.gov (United States)

    Elkacmi, Reda; Kamil, Noureddine; Bennajah, Mounir; Kitane, Said

    2016-01-01

    The production of olive oil in Morocco has recently grown considerably for its economic and nutritional importance favored by the country's climate. After the extraction of olive oil by pressing or centrifuging, the obtained liquid contains oil and vegetation water which is subsequently separated by decanting or centrifugation. Despite its treatment throughout the extraction process, this olive mill wastewater, OMW, still contains a very important oily residue, always regarded as a rejection. The separated oil from OMW can not be intended for food because of its high acidity of 3.397% which exceeds the international standard for human consumption defined by the standard of the Codex Alimentarius, proving its poor quality. This work gives value addition to what would normally be regarded as waste by the extraction of oleic acid as a high value product, using the technique of inclusion with urea for the elimination of saturated and unsaturated fatty acids through four successive crystallizations at 4°C and 20°C to have a final phase with oleic acid purity of 95.49%, as a biodegradable soap and a high quality glycerin will be produced by the reaction of saponification and transesterification.

  5. Scaling neutron absorbed dose distributions from one medium to another

    International Nuclear Information System (INIS)

    Awschalom, M.; Rosenberg, I.; Ten Haken, R.K.

    1982-11-01

    Central axis depth dose (CADD) and off-axis absorbed dose ratio (OAR) measurements were made in water, muscle and whole skeletal bone TE-solutions, mineral oil and glycerin with a clinical neutron therapy beam. These measurements show that, for a given neutron beam quality and field size, there is a universal CADD distribution at infinity if the depth in the phantom is expressed in terms of appropriate scaling lengths. These are essentially the kerma-weighted neutron mean free paths in the media. The method used in ICRU No. 26 to scale the CADD by the ratio of the densities is shown to give incorrect results. the OAR's measured in different media at depths proportional to the respective mean free paths were also found to be independent of the media to a good approximation. It is recommended that relative CADD and OAR measurements be performed in water because of its universality and convenience. A table of calculated scaling lengths is given for various neutron energy spectra and for various tissues and materials of practical importance in neutron dosimetry

  6. Comparative study of analgesic effect of the infrared low-intensity laser and 33% sodium fluoride paste in the treatment of dentinal hypersensitivity

    International Nuclear Information System (INIS)

    Oliveira, Glen Anderson Maia de

    2003-01-01

    Different desensitizing agents have been used in the treatment of dentinal hypersensitivity, however, some presented treatments are still frustrating. The purpose of this study was to evaluate the analgesic effect of the low-intensity GaAlAs laser (λ= 830 nm) in the treatment of dentinal hypersensitivity after mechanical and thermal stimuli, and compared it with the 33% sodium fluoride paste. Thirty two teeth with dentinal hypersensitivity were selected and randomly divided into two groups. For the laser group, each tooth was irradiated by a dose of 6 J/cm 2 during two minutes and half on the buccal side. The paste group was treated with a NaF/kaolin/glycerin (33:33:33) paste by burnishing the sensitive surface during four minutes. The sensitivity degree was measured before the beginning of the experiment, 24 h, 48 h, 72 h, 120 h, 15 days and 30 days after the first application. The results indicate that the dentinal hypersensitivity significantly diminished for the paste group after dental explorer. Regarding to air-blast, no significant differences were observed between the groups. Both of them were effective in reducing pain of the dentine hypersensitive after 120 h. (author)

  7. Preparation and Evaluation of Novel In Situ Gels Containing Acyclovir for the Treatment of Oral Herpes Simplex Virus Infections

    Directory of Open Access Journals (Sweden)

    Binu Chaudhary

    2014-01-01

    Full Text Available The objective of this work was to develop an oral mucosal drug delivery system to facilitate the local and systemic delivery of acyclovir for the treatment of oral herpes infection caused by the herpes simplex virus (HSV. An in situ gelling system was used to increase the residence time and thus the bioavailability of acyclovir in oral mucosa. Temperature and pH trigged in situ gel formulations were prepared by cold method using polymers like poloxamer 407, carbopol 934, and HPMC. Glycerin and a mixture of tween 80 and ethanol (1 : 2 ratio were used as the drug dissolving solvent. The pH of carbopol containing formulation was adjusted to pH 5.8 while the pH of poloxamer solution was adjusted to pH 7. These formulations were evaluated for sol-gel transition temperature, gelling capacity, pH, viscosity, spreadability, gel strength, drug content, ex-vitro permeation, and mucoadhesion. The gelation temperatures of all the formulations were within the range of 28–38°C. All the formulations exhibited fairly uniform drug content (98.15–99.75%. Drug release study of all the formulations showed sustained release properties. The release of drug through these in situ gel formulations followed the Higuchi model and Korsmeyer peppas model mechanism.

  8. Not just rocket science

    Energy Technology Data Exchange (ETDEWEB)

    MacAdam, S.; Anderson, R. [Celan Energy Systems, Rancho Cordova, CA (United States)

    2007-10-15

    The paper explains a different take on oxyfuel combustion. Clean Energy Systems (CES) has integrated aerospace technology into conventional power systems, creating a zero-emission power generation technology that has some advantages over other similar approaches. When using coal as a feedstock, the CES process burns syngas rather than raw coal. The process uses recycled water and steam to moderate the temperature, instead of recycled CO{sub 2}. With no air ingress, the CES process produces very pure CO{sub 2}. This makes it possible to capture over 99% of the CO{sub 2} resulting from combustion. CES uses the combustion products to drive the turbines, rather than indirectly raising steam for steam turbines, as in the oxyfuel process used by companies such as Vattenfall. The core of the process is a high-pressure oxy-combustor adapted from rocket engine technology. This combustor burns gaseous or liquid fuels with gaseous oxygen in the presence of water. Fuels include natural gas, coal or coke-derived synthesis gas, landfill and biodigester gases, glycerine solutions and oil/water emulsion. 2 figs.

  9. Evaluation of Two Commercially Available Cannabidiol Formulations for use in Electronic Cigarettes

    Directory of Open Access Journals (Sweden)

    Michelle R Peace

    2016-08-01

    Full Text Available With 24 states and the District of Columbia with laws legalizing marijuana in some form, suppliers of legal marijuana have developed Cannabis sativa products for use in electronic cigarettes. Personal battery powered vaporizers or electronic cigarettes were developed to deliver a nicotine vapor such that smokers could simulate smoking tobacco without the inherent pathology of inhaled tobacco smoke. The liquid formulations used in these devices are comprised of an active ingredient such as nicotine mixed with glycerin and/or propylene glycol and flavorings. A significant active ingredient of Cannabis sativa, cannabidiol, has been purported to have anti-convulsant, anti-nociceptive, and anti-psychotic properties. These properties have potential medical therapies such as intervention of addictive behaviors, treatments for epilepsy, management of pain for cancer patients, and treatments for schizophrenia. However, cannabidiol extracted from Cannabis sativa remains a DEA Schedule I drug since it has not been approved by the FDA for medical purposes. Two commercially available e-cigarette liquid formulations reported to contain 3.3 mg/mL of cannabidiol as the active ingredient were evaluated. These products are not regulated by the Food and Drug Administration in manufacturing or in labeling of the products and were found to contain 6.5 mg/mL and 7.6 mg/mL of cannabidiol in propylene glycol with a variety of flavoring agents. Presently, while labeled as to content, the quality control of manufacturers and the relative safety of these products is uncertain.

  10. Management of full term pregnant patient with paroxysmal hypertension due to incidental pheochromocytoma

    Directory of Open Access Journals (Sweden)

    S. Sahu*

    2013-12-01

    Case Description: A 25-year-old, full-term pregnant woman diagnosed with pre-eclampsia was referred to our tertiary care hospital with severe resistant hypertension. Her blood pressure remained labile despite the usual medications, which led to the suspicion of an underlying endocrinological problem. Further biochemical and radiological investigations confirmed the diagnosis of pheochromocytoma. The patient was invasively monitored and treated with alpha blockade, beta blocker, and vasodilators in ICU. On the fifth day, she went into spontaneous labour with confirmed rupture of the membranes. The labour was augmented with intravenous oxytocin 2U in 500 ml solution of Ringer’s lactate. A nitro-glycerine basal infusion was started and titrated to control BP during labour to keep the blood pressure below 160/90 mmHg. An injection of Phentolamine drip and beta blocker esmolol was kept ready, to control the wide fluctuation of blood pressure. She delivered a live, healthy, male infant weighing 2.5 Kg. She was kept in the ICU for 72 h with epidural patient-controlled analgesia (EPCA. The patient was not keen for a resection of the adrenal tumour immediately after delivery. She was discharged with medical management, with a further plan for surgery in due course. With a multidisciplinary team approach (gynaecologist, anaesthesiologist, endocrinologist, and surgeon, proper planning, and adequate preoperative medical management; pheochromocytoma in pregnancy can be managed successfully.

  11. Free-surface entrainment into a rimming flow containing surfactants

    Science.gov (United States)

    Thoroddsen, S. T.; Tan, Y.-K.

    2004-02-01

    We study experimentally the free-surface entrainment of tubes into a steady rimming flow formed inside a partially filled horizontally rotating cylinder. The liquid consists of a glycerin-water mixture containing surfactants (fatty acids). The phenomenon does not occur without the surfactants and the details are sensitive to their concentration. The entrainment of numerous closely spaced air tubes and/or surfactant columns can start intermittently along a two-dimensional stagnation line, but is usually associated with the appearance of an axially periodic vortex structure, the so-called shark teeth, which fixes the spanwise location of these tubes. The number of tubes is governed by the three-dimensional shape of the free surface, reducing from more than 10 to only two in each trough, as the rotation rate is increased. The tubes vary in diameter from 10-30 μm and can extend hundreds of diameters into the liquid layer before breaking up into a continuous stream of bubbles and/or drops. The tubes are driven through the stagnation line by the strong viscous shear and are stretched in the downstream direction. The entrainment starts when the Capillary number Ca=μωR/σ≃0.4.

  12. TRANSFORMATION OF POTATO STARCH, NOPAL MUCYLAGA AND BIOPLAST LABELS AS AGGREGATE VALUE PRODUCTS FRIENDLY WITH THE ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Angel Issac Moreno-Bustillos

    2017-07-01

    Full Text Available This experimental research, carried out at the Instituto Tecnológico Superior de Guasave, asseses the obtainment of an environmentally friendly bioplastic, as an alternative to polymers of synthetic origin, and with this, to reduce the environmental impacts generated by them. For this, it was considered the lagging potato as a source of starch, in addition to regional nopal and aloe, as a source of mucilage. Glycerin was used as a plasticizer. In order to determine the purity degree of the materials, physicochemical properties were analyzed by the AOAC official methods. Films of 3mm thick per 100mm long were made from different concentration of the materials, an experimental design (DOE 2^5, with two levels and five independent factors was established; resulting in 32 treatments, with two replicates per treatment. The response variables: odor, appearance, ease of molding and resistance to touch were evaluated qualitatively. From the total of the analyzed samples only 6 treatments (corresponding to 18.75% met the attributes of touch resistance and ease of molding.

  13. Study on Combustion Performance of Diesel Engine Fueled by Synthesized Waste Cooking Oil Biodiesel Blends

    Directory of Open Access Journals (Sweden)

    Duraid F. Maki

    2018-02-01

    Full Text Available The waste cooking oil or used cooking oil is the best source of biodiesel synthesizing because it enters into the so-called W2E field whereas not only get rid of the used cooking oils but produce energy from waste fuel. In this study, biodiesel was synthesized from the used cooking oil and specifications are tested. From 1 liter of used cooking oil, 940 ml is gained. The remaining of liter is glycerin and water. Blend of 20% of biodiesel with 80% of net diesel by volume is formed. Blends of 100% diesel and 100% biodiesel are prepared too. The diesel engine combustion performance is studied. Brake thermal efficiency, brake specific fuel consumption, volumetric efficiency, mean effective pressure, and engine outlet temperature. Cylinder pressure variation with crank angle is analyzed. At last not least, the concentrations of hydro carbon and nitrogen pollutants are measured. The results showed significant enhancement in engine power and pollutant gases emitted. There is positive compatible with other critical researches.

  14. Comparative study of analgesic effect of the infrared low-intensity laser and 33% sodium fluoride paste in the treatment of dentinal hypersensitivity; Estudo comparativo do efeito analgesico do laser em baixa intensidade de emissao infravermelha e da pasta de fluoreto de sodio a 33% no tratamento da hipersensibilidade dentinaria

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Glen Anderson Maia de

    2003-07-01

    Different desensitizing agents have been used in the treatment of dentinal hypersensitivity, however, some presented treatments are still frustrating. The purpose of this study was to evaluate the analgesic effect of the low-intensity GaAlAs laser ({lambda}= 830 nm) in the treatment of dentinal hypersensitivity after mechanical and thermal stimuli, and compared it with the 33% sodium fluoride paste. Thirty two teeth with dentinal hypersensitivity were selected and randomly divided into two groups. For the laser group, each tooth was irradiated by a dose of 6 J/cm{sup 2} during two minutes and half on the buccal side. The paste group was treated with a NaF/kaolin/glycerin (33:33:33) paste by burnishing the sensitive surface during four minutes. The sensitivity degree was measured before the beginning of the experiment, 24 h, 48 h, 72 h, 120 h, 15 days and 30 days after the first application. The results indicate that the dentinal hypersensitivity significantly diminished for the paste group after dental explorer. Regarding to air-blast, no significant differences were observed between the groups. Both of them were effective in reducing pain of the dentine hypersensitive after 120 h. (author)

  15. Solubility investigation of ether and ester essential oils in water using spectrometry and GC/MS

    Directory of Open Access Journals (Sweden)

    B. Khodabandeloo

    2017-11-01

    Full Text Available Background and objectives: Essential oils (volatiles are aromatic oily liquids prepared from different parts of plants and demonstrate various therapeutic and cosmetic properties. The dissolution of essential oils are not desirable in water, therefore the aim of this research was evaluation and selection the best co-solvents for increasing their solubility and bio availability. Methods:The solubility of six  plants essential oils were investigated in presence of propylene glycol (PG, polyethylene glycol 300 (PEG, glycerin and ethanol as solvent and tween 80 or lecithin as co-solvent by observation and spectrophotometric assay. Chemical composition of the essential oils and supersaturated 50% ethanol (SSE and 50% PG or PEG (SSP solutions were analyzed by GC/MS, too. Results: Ester (Lavandula dentata, Heracleum persicum and, Elettaria cardamomum essential oils showed the best solubility in ethanol and PG, respectively. Ether (Foeniculum vulgare, Pimpinella anisum and Petroselinum crispum essential oils had the best solubility in ethanol and PEG, respectively. In ester class, mixture of ethanol/water was the best solvent according to solubility and total amounts of major compounds of the essential oils. In ether class, all samples had better solubility in mixtures of ethanol/water than PEG, but the amounts of total phenols or ethers in SSP of some samples were higher than SSE. Therefore selecting the best solvent for these class need more experiments. Conclusion: Selecting the solvent for essential oils changes their chemical composition; therefore the best solvent was different for various purposes.

  16. Hand hygiene in peritoneal dialysis patients: a comparison of two techniques.

    Science.gov (United States)

    Figueiredo, Ana Elizabeth; de Siqueira, Soraia Lemos; Poli-de-Figueiredo, Carlos Eduardo; d'Avila, Domingos O

    2013-01-01

    Hand hygiene is essential for preventing peritoneal dialysis (PD)-related infections. The present study compared the effectiveness of two hygiene techniques in reducing the number of colony-forming units (CFUs) on the hands of patients undergoing PD. In this controlled clinical trial, 22 participants enrolled in the same PD program underwent a two-hand evaluation for microbiologic flora. Participants participated in two treatments: a) simple hand hygiene plus antiseptic hand hygiene, in which the patients washed their hands with water and glycerin soap for 1 minute and then rubbed and dried their hands with 70% ethyl alcohol gel; and b) antiseptic hand hygiene, in which the patients rubbed their hands with 70% ethyl alcohol gel until fully dry. To sample distal finger surfaces, we asked the participants to touch sheep blood agar plates directly. The CFU count for both hands was significantly higher in the regular hygiene group than in the gel-only group [69.0 (16.0 - 101.0) CFU vs 9.0 (2.2 - 55.5) CFU, p hand cultures from the regular hygiene group than in those from the gel-only group [69.5 (26.25 - 101.0) CFU vs 9.5 (1.0 - 41.7) CFU; p hands may be more effective than following the regular hygiene recommendations in reducing bacterial populations.

  17. Electron beam irradiation and addition of poly(vinyl alcohol) affect gelatin based-films properties

    International Nuclear Information System (INIS)

    Inamura, Patricia Y.; Mastro, Nelida L. del

    2015-01-01

    Gelatin is a mixture of high molecular weight polypeptides, product of denaturation, and partial structural degradation of collagen, and one of the first materials employed as biomaterials. Aqueous solutions of gelatin (10%), glycerin as plasticizer and poly(vinyl alcohol) (PVA) up to 10% were prepared in a water bath at 70 deg C under constant stirring. Films were irradiated with 10 and 20 kGy using an electron beam accelerator, dose rate of 22.4 kGy s -1 , energy 1.407 MeV, at room temperature, in the presence of air. After irradiation, mechanical properties, color measurements, water absorption, moisture and film solubility were analyzed. The films showed an improvement in maximum force to rupture the film with increase of the irradiation dose. The higher the puncture force to rupture the lower the elongation at break. Colorimetric tests showed significant differences between samples, and also differences depending of the applied radiation dose, and analyzed color parameter. In water absorption tests a decrease of absorption percentage was found with the increase of the dose for PVA free and 5% PVA samples. The addition of PVA increased the water absorption for all applied doses. The modifications in gelatin colloids can be appointed to radiation-induced crosslinking. Also, the PVA concentration in the samples influenced the resultant material properties. (author)

  18. Frontal Cortex Transcriptome Analysis of Mice Exposed to Electronic Cigarettes During Early Life Stages

    Science.gov (United States)

    Lauterstein, Dana E.; Tijerina, Pamella B.; Corbett, Kevin; Akgol Oksuz, Betul; Shen, Steven S.; Gordon, Terry; Klein, Catherine B.; Zelikoff, Judith T.

    2016-01-01

    Electronic cigarettes (e-cigarettes), battery-powered devices containing nicotine, glycerin, propylene glycol, flavorings, and other substances, are increasing in popularity. They pose a potential threat to the developing brain, as nicotine is a known neurotoxicant. We hypothesized that exposure to e-cigarettes during early life stages induce changes in central nervous system (CNS) transcriptome associated with adverse neurobiological outcomes and long-term disease states. To test the hypothesis, pregnant C57BL/6 mice were exposed daily (via whole body inhalation) throughout gestation (3 h/day; 5 days/week) to aerosols produced from e-cigarettes either with nicotine (13–16 mg/mL) or without nicotine; following birth, pups and dams were exposed together to e-cigarette aerosols throughout lactation beginning at postnatal day (PND) 4–6 and using the same exposure conditions employed during gestational exposure. Following exposure, frontal cortex recovered from ~one-month-old male and female offspring were excised and analyzed for gene expression by RNA Sequencing (RNA-Seq). Comparisons between the treatment groups revealed that e-cigarette constituents other than nicotine might be partly responsible for the observed biological effects. Transcriptome alterations in both offspring sexes and treatment groups were all significantly associated with downstream adverse neurobiological outcomes. Results from this study demonstrate that e-cigarette exposure during early life alters CNS development potentially leading to chronic neuropathology. PMID:27077873

  19. A Study of Mutation Breeding of High-Yielding Tryptophanase Escherichia coli by Low-Energy N+ Ion Beam Implantation

    International Nuclear Information System (INIS)

    Pang Min; Yao Jianming; Wang Dongmei

    2009-01-01

    Low energy ion beam has been widely applied in microbe breeding, plant breeding, gene transfer and cell modification. In this study, the Escherichia coli (E.coli) strain producing tryptophanase was irradiated by a low energy nitrogen ion beam with an energy of 10 keV at a fluence of 13 x 10 14 N + /cm 2 when glycerin at a 15% concentration was used as a protector. The effect on the biomass of E. coli after N + implantation was analyzed in detail by statistic methods. The screening methods used in this study were proven to be effective. After continuous mutagenicity, a high-yield tryptophanase strain was selected and both its biomass and enzymatic activity were higher than those of the parent strain. The results of scale-up production showed that the biomass could reach wet weight 8.2 g/L and 110 g L-tryptophan could be formed in the volume of the 1l enzymatic reaction system.

  20. Electron beam irradiation and addition of poly(vinyl alcohol) affect gelatin based-films properties

    Energy Technology Data Exchange (ETDEWEB)

    Inamura, Patricia Y.; Mastro, Nelida L. del, E-mail: pinamura@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    Gelatin is a mixture of high molecular weight polypeptides, product of denaturation, and partial structural degradation of collagen, and one of the first materials employed as biomaterials. Aqueous solutions of gelatin (10%), glycerin as plasticizer and poly(vinyl alcohol) (PVA) up to 10% were prepared in a water bath at 70 deg C under constant stirring. Films were irradiated with 10 and 20 kGy using an electron beam accelerator, dose rate of 22.4 kGy s{sup -1}, energy 1.407 MeV, at room temperature, in the presence of air. After irradiation, mechanical properties, color measurements, water absorption, moisture and film solubility were analyzed. The films showed an improvement in maximum force to rupture the film with increase of the irradiation dose. The higher the puncture force to rupture the lower the elongation at break. Colorimetric tests showed significant differences between samples, and also differences depending of the applied radiation dose, and analyzed color parameter. In water absorption tests a decrease of absorption percentage was found with the increase of the dose for PVA free and 5% PVA samples. The addition of PVA increased the water absorption for all applied doses. The modifications in gelatin colloids can be appointed to radiation-induced crosslinking. Also, the PVA concentration in the samples influenced the resultant material properties. (author)

  1. Investigation of processes of interaction relativistic electrons with the solutions of organic dyes

    International Nuclear Information System (INIS)

    Buki, A.Yu.; Gokov, S.P.; Kazarinov, Yu.G.; Kalenik, S.A.; Kasilov, V.I.; Kochetov, S.S.; Makhnenko, P.L.; Mel'nitskiy, I.V.; Tverdohvalov, A.V.; Tsyatsko, V.V.; Shopen, O.A.

    2014-01-01

    Investigation of the processes of interaction of ionizing radiation with complex organic objects can solve a number of fundamental and applied problems in radiation physics, chemistry and biology. In this work we investigated the dose dependence (dose range 1...5MRad) optical density relative concentrations of water, alcohol and glycerine solution following organic dyes: methylene blue - C 16 H 18 N 3 SCl and methyl orange - C 14 H 14 N 3 O 3 SNa, irradiated with an electron beam with an energy of 16MeV. In the analysis of absorption spectra, it was found that water solutions of dyes have less resistance to radiation as compared with the alcohol and glycerol. Also, all solutions of methyl orange less radiation resistant than the methylene blue solution. Analysis of the spectra showed that these relationships are close to linear in the range of doses. To understand the physical and chemical processes occurring in the interaction of relativistic electrons with the studied organic objects were performed the computer simulations of the energy spectra of ions formed due to breaking the chemical bonds of molecules of dye solutions using the program SRIM-2010. The analysis showed that radiation - stimulated chemical processes play a major role in the destruction of the source of organic dye molecules. The remaining processes (interaction of electrons and nuclei, the cascade processes) accounts for about 10% of all molecular breaks.

  2. Extraction of Oleic Acid from Moroccan Olive Mill Wastewater

    Directory of Open Access Journals (Sweden)

    Reda Elkacmi

    2016-01-01

    Full Text Available The production of olive oil in Morocco has recently grown considerably for its economic and nutritional importance favored by the country’s climate. After the extraction of olive oil by pressing or centrifuging, the obtained liquid contains oil and vegetation water which is subsequently separated by decanting or centrifugation. Despite its treatment throughout the extraction process, this olive mill wastewater, OMW, still contains a very important oily residue, always regarded as a rejection. The separated oil from OMW can not be intended for food because of its high acidity of 3.397% which exceeds the international standard for human consumption defined by the standard of the Codex Alimentarius, proving its poor quality. This work gives value addition to what would normally be regarded as waste by the extraction of oleic acid as a high value product, using the technique of inclusion with urea for the elimination of saturated and unsaturated fatty acids through four successive crystallizations at 4°C and 20°C to have a final phase with oleic acid purity of 95.49%, as a biodegradable soap and a high quality glycerin will be produced by the reaction of saponification and transesterification.

  3. Sub-Microscopic Organization and Functional Properties of Cells Stored in a Bank for Frozen Leucocytes and Platelets

    Energy Technology Data Exchange (ETDEWEB)

    Vinograd-Finkel, F. R.; Terentieva, E. I.; Leontovich, V. A.; Skopina, S. B.; Abezgauz, N. N.; Totskaya, A. A. [Central Institute of Haematology and Blood Transfusion, Moscow, USSR (Russian Federation)

    1969-07-15

    Massive transfusions of leucocyte mass containing young and stem cells in addition to adult cells are carried out successfully in the treatment of patients suffering from depressed haemopoiesis. To meet the needs of clinics a leucocyte mass bank-has been established and methods have been developed for the long-term storage of leucocyte mass by keeping it in the frozen state at -196 Degree-Sign C. Various carrier solutions containing cryoprotective substances (dimethylsulphoxide, glycerine, polyvinyl pyrrolidone) have been proposed. These make it possible to conserve from 70 to 90% of live cells for as long as two years or more. The viability of the frozen cells is proved by supravital staining and luminescent microscopy, and also by determining the extent to which their functional properties are preserved, the phagocytic activity of the granulocytes and the ability of the lymphocytes to produce young forms in tissue culture. It has also been observed that their glycolytic activity is preserved (up to 60%). All these data correlate with the data obtained by electron microscopy regarding the extent to which the sub-microscopic organization of frozen leucocytes is preserved. The bank is also used to store a frozen platelet mass, dimethylsulphoxide being used as the cryoprotective agent. The ultrastructure of the platelets and their functional properties (retractile activity) suffer least impairment. (author)

  4. Clearing and dissecting insects for internal skeletal morphological research with particular reference to bees

    Directory of Open Access Journals (Sweden)

    Diego Sasso Porto

    2016-03-01

    Full Text Available ABSTRACT A detailed protocol for chemical clearing of bee specimens is presented. Dry specimens as well as those preserved in liquid media can be cleared using this protocol. The procedure consists of a combined use of alkaline solution (KOH or NaOH and hydrogen peroxide (H2O2, followed by the boiling of the cleared specimens in 60–70% EtOH. Clearing is particularly useful for internal skeletal morphological research. This procedure allows for efficient study of internal projections of the exoskeleton (e.g., apodemes, furcae, phragmata, tentoria, internal ridges and sulci, but this process makes external features of the integument, as some sutures and sulci, readily available for observation as well. Upon completion of the chemical clearing process the specimens can be stored in glycerin. This procedure was developed and evaluated for the preparation of bees and other Apoidea, but modifications for use with other insect taxa should be straightforward after some experimentation on variations of timing of steps, concentration of solutions, temperatures, and the necessity of a given step. Comments on the long-term storage, morphological examination, and photodocumentation of cleared specimens are also provided.

  5. Biofuels - Illusion or Reality? - The european experience

    International Nuclear Information System (INIS)

    Furfari, A.

    2008-01-01

    Environmental issues, rising prices and security of supply are putting energy at the centre of all attentions. Policy-makers pushed by various stakeholders are struggling to find more sustainable solutions to the world legitimate demand for energy. The transport sector is especially under pressure as it relies for 98% on oil. Despite vast research and development investments, no short-term solutions appeared to be reliable. Thanks to lawmakers support to biofuels, these substitutes for oil are now seen as the potential solution for a sustainable transport. This book analyses the real possibility of biofuels. Does Europe has enough land to produce the needed feedstock? What are the real gains in terms of greenhouse gases emissions and energy efficiency? Are biofuels really a sustainable solution? Will this policy succeed? Are the targets reachable? The reader will find some indications in this book to make up his mind on this complex, multifaceted and highly political subject. Contents: Summary. Introduction. Biofuels in the U.S.A. and Brazil. Do we have enough land in Europe? Biofuels life cycle analysis. Greenhouse gases reduction and efficiency. Case of the glycerin price. Variables affecting biofuels sustainability. Standard for Biofuels. Conclusion. General Bibliography. Annexes. References

  6. Preparation and Properties of Superamphiphobic Wear-resistance PPS-based Coating

    Directory of Open Access Journals (Sweden)

    WANG Huai-yuan

    2017-01-01

    Full Text Available Superamphiphobic wear-resistance PPS-based coatings were prepared by a simple spraying method with a pore-forming reagent of NH4HCO3 and nano-filler of carbon nanotubes (CNTs.The surface morphology and the hydrophobicity,oleophobicity of the coating were analyzed by scanning electron microscope (SEM and contact angle meter.The wear-resistance of the coating was verified by sanding method with given load.The results indicate that a rough surface is obtained after pore-forming,and the porous structures in combination with the CNTs construct the special micro/nano-scale network structures.When the mass fraction of NH4HCO3 is 5%,the contact angles of the coating for water,glycerine and ethylene glycol are 162°,158° and 152°,showing superamphiphobic property.After polished 10000 times by abrasive paper,the coating shows slight friction marks and remains high hydrophobicity,exhibiting excellent wear-resistance.

  7. Fluorescent silica colloids for study and visualization of skin care products.

    Science.gov (United States)

    Iyer, Swaminathan; Kievsky, Yaroslav; Sokolov, Igor

    2007-08-01

    The efficacy of skin care products depends on the time and dynamics of their absorbance by the skin, and its spatial distribution on the skin. Regular scrape-based methods may depend on the operator and are destructive and invasive in nature. Here, we describe a novel method based on non-contact optical measurements to trace the location and dynamics of skin care products on the skin. We use fluorescent silica colloidal particles of micron sizes at a rather small concentration as non-invasive tracers. As an example of skin care products, we use two base materials: either glycerin or vaseline. A mixture of each product with fluorescent particles is applied on human skin. The amount of fluorescence is monitored by means of a fluorescent spectrometer. The scraping method is used to compare with the spectroscopic measurements. Fluorescent tracers make the skin care product visible under UV light. This allows obtaining an optical image of the spatial distribution of the product on the skin. The quantitative data of fluorescence are well correlated with the scrape data. Comparison of the difference in the spectral and scraped mass data reveals the details of accumulation of the skin products in skin cracks and crevices. We described an efficient non-invasive benign method to quantify dynamics and to perform mapping of emollients and humectants on the skin.

  8. Active agents in common skin care products.

    Science.gov (United States)

    Draelos, Zoe Diana

    2010-02-01

    Skin care products are numerous and perplexing, yet the majority fall into the moisturizer category. Moisturizers are substances designed to improve and maintain the skin barrier. They serve as a vehicle for the delivery of active ingredients that minimize facial lines of dehydration, deliver photoprotection, and provide antioxidant properties. Moisturizers are based on occlusive substances, such as petrolatum and dimethicone, and humectant substances, such as glycerin, with a variety of sunscreens and botanicals for added functionality and marketing impact. This article reviews these common active agents. The plethora of over-the-counter skin care products available for patient purchase is overwhelming, yet there is certain commonality among 80 percent of the formulations. The majority of the products are moisturizers with added ingredients to support marketing claims. Whether the product is a facial foundation, an antiaging night cream, a sunscreen, a topical antioxidant, or a skin-lightening serum, the formulation is basically a moisturizer. Sunscreen is the most biologically active antiaging ingredient in skin care products, but the antiinflammatory and antioxidant effects of botanicals possess tremendous marketing appeal.

  9. Biotechnological processes for biodiesel production using alternative oils

    Energy Technology Data Exchange (ETDEWEB)

    Azocar, Laura; Ciudad, Gustavo [La Frontera Univ., Temuco (Chile). Nucleo Cietifico Tecnologico en Biorrecursos; Heipieper, Hermann J. [Helmholtz Centre for Environmental Research-UFZ, Leipzig (Germany). Dept. of Environmental Biotechnology; Navia, Rodrigo [La Frontera Univ., Temuco (Chile). Nucleo Cietifico Tecnologico en Biorrecursos; La Frontera Univ., Temuco (Chile). Dept. de Ingenieria Quimica

    2010-10-15

    As biodiesel (fatty acid methyl ester (FAME)) is mainly produced from edible vegetable oils, crop soils are used for its production, increasing deforestation and producing a fuel more expensive than diesel. The use of waste lipids such as waste frying oils, waste fats, and soapstock has been proposed as low-cost alternative feedstocks. Non-edible oils such as jatropha, pongamia, and rubber seed oil are also economically attractive. In addition, microalgae, bacteria, yeast, and fungi with 20% or higher lipid content are oleaginous microorganisms known as single cell oil and have been proposed as feedstocks for FAME production. Alternative feedstocks are characterized by their elevated acid value due to the high level of free fatty acid (FFA) content, causing undesirable saponification reactions when an alkaline catalyst is used in the transesterification reaction. The production of soap consumes the conventional catalyst, diminishing FAME production yield and simultaneously preventing the effective separation of the produced FAME from the glycerin phase. These problems could be solved using biological catalysts, such as lipases or whole-cell catalysts, avoiding soap production as the FFAs are esterified to FAME. In addition, by-product glycerol can be easily recovered, and the purification of FAME is simplified using biological catalysts. (orig.)

  10. Ultrasound assisted production of fatty acid methyl esters from transesterification of triglycerides with methanol in the presence of KOH catalyst: optimization, mechanism and kinetics.

    Science.gov (United States)

    Thanh, Le Tu; Okitsu, Kenji; Maeda, Yasuaki; Bandow, Hiroshi

    2014-03-01

    Ultrasound assisted transesterification of triglycerides (TG) with methanol in the presence of KOH catalyst was investigated, where the changes in the reactants and products (diglycerides (DG), monoglycerides (MG), fatty acid methyl esters (FAME) and glycerin (GL)) concentrations were discussed to understand the reaction mechanism and kinetics under ultrasound irradiation. The optimum reaction condition for the FAME production was the concentration of KOH 1.0 wt.%, molar ratio of TG to methanol of 1:6, and irradiation time of 25 min. The rate constants during the TG transesterification with methanol into GL and FAME were estimated by a curve fitting method with simulated curves to the obtained experimental results. The rate constants of [Formula: see text] were estimated to be 0.21, 0.008, 0.23, 0.005, 0.14 and 0.001 L mol(-1)min(-1), respectively. The rate determining step for the TG transesterification with methanol into GL and FAME was the reaction of MG with methanol into GL and FAME. Copyright © 2013 Elsevier B.V. All rights reserved.

  11. [Development of biphasic drug-loading lipid emulsion of Salvia miltiorrhiza and its quality evaluation].

    Science.gov (United States)

    Wang, Yin-Yan; Li, Xi; Lai, Xiu-Jun; Li, Wei; Yang, Ya-Jing; Chu, Ting; Mao, Sheng-Jun

    2014-10-01

    The feasibility of simultaneously loading both liposoluble and water-soluble components of Salvia miltiorrhiza in emulsion was discussed, in order to provide new ideas in comprehensive application of effective components in S. miltiorrhiza in terms of technology of pharmaceutics. With tanshinone II (A) and salvianolic acid B as raw materials, soybean phospholipid and poloxamer 188 as emulsifiers, and glycerin as isoosmotic regulator, the central composite design-response surface method was employed to optimize the prescription. The coarse emulsion was prepared with the high-speed shearing method and then homogenized in the high pressure homogenizer. The biphasic drug-loading intravenous emulsion was prepared to investigate its pharmaceutical properties and stability. The prepared emulsion is orange-yellow, with the average diameter of 241 nm and Zeta potential of -35.3 mV. Specifically, the drug loading capacity of tanshinone II (A) and salvianolic acid B were 0.5 g x L(-1) and 1 g x L(-1), respectively, with a good stability among long-term retention samples. According to the results, the prepared emulsion could load liposoluble tanshinone II (A) and water-soluble salvianolic acid B simultaneously, which lays a pharmaceutical foundation for giving full play to the efficacy of S. miltiorrhiza.

  12. A New and Sound Technology for Biogas from Solid Waste and Biomass

    International Nuclear Information System (INIS)

    Busch, G.; Grossmann, J.; Sieber, M.; Burkhardt, M.

    2009-01-01

    Organic waste, as a main constituent of municipal solid waste, has as well as solid biomass a high potential for biogas generation. Despite the importance of biogas generation from these materials, the availability of large-scale biogas processes lacks behind the demand. A newly developed double-stage solid-liquid biogas process, consisting of an open hydrolysis stage and a fixed-bed methane reactor, allows the biogas production from almost all biodegradable solid waste and renewable resources like maize, grass, sugar cane, etc. Furthermore, residues from industrial processes, like the glycerine waste water from biodiesel production, can also be converted into biogas successfully. Due to the strong separation of hydrolysis and methanation, the process is extremely stable. No malfunction has been detected so far. The open hydrolysis releases CO 2 and allows oxidation of sulfur. Consequently, the biogas has a high methane (>72%) and low H 2 S concentration (<100 ppm). Stirrers or other agitation equipment are not necessary; only liquids are pumped. The biogas generation becomes controllable for the first time; thus, the actual generation can be easily adapted to the consumption

  13. Mathematical Modeling of Rotary Blood Pumps in a Pulsatile In Vitro Flow Environment.

    Science.gov (United States)

    Pirbodaghi, Tohid

    2017-08-01

    Nowadays, sacrificing animals to develop medical devices and receive regulatory approval has become more common, which increases ethical concerns. Although in vivo tests are necessary for development and evaluation of new devices, nonetheless, with appropriate in vitro setups and mathematical models, a part of the validation process can be performed using these models to reduce the number of sacrificed animals. The main aim of this study is to present a mathematical model simulating the hydrodynamic function of a rotary blood pump (RBP) in a pulsatile in vitro flow environment. This model relates the pressure head of the RBP to the flow rate, rotational speed, and time derivatives of flow rate and rotational speed. To identify the model parameters, an in vitro setup was constructed consisting of a piston pump, a compliance chamber, a throttle, a buffer reservoir, and the CentriMag RBP. A 40% glycerin-water mixture as a blood analog fluid and deionized water were used in the hydraulic circuit to investigate the effect of viscosity and density of the working fluid on the model parameters. First, model variables were physically measured and digitally acquired. Second, an identification algorithm based on regression analysis was used to derive the model parameters. Third, the completed model was validated with a totally different set of in vitro data. The model is usable for both mathematical simulations of the interaction between the pump and heart and indirect pressure measurement in a clinical context. © 2017 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

  14. The influence of atomizer internal design and liquid physical properties on effervescent atomizing of coal-water slurry

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Meng; Duan, Yufeng [Southeast Univ., Nanjing (China). Inst. of Thermal Engineering

    2013-07-01

    This study investigated the dependence of effervescent atomizing of coal-water slurry (CWS) on atomizer internal design and fluid properties. Results demonstrate that internal design of atomizer and fluid properties directly affect the two-phase flow pattern inside the atomizer which consequently affects the spray quality. The influence of mixing chamber length on spray quality is not significant at the ALR of 0.15 except for spray 0.75 glycerol/0.248 water/0.002 xanthan mixture. The same trend also found in the effect of angle of aeration holes at ALR of 0.15. Large diameter of the inclined aeration holes shows small SMD for water. The consistency index of fluids has no effect on the spray quality and Sauter Mean Diameter (SMD) increases when polymer additions were added to the glycerin-water mixture. The radial profile of SMD for spray water are almost flat, however, the largest SMD can be obtained at the edge of spray for three other fluids.

  15. The Effect of Pitching Phase on the Vortex Circulation for a Flapping Wing During Stroke Reversal

    Science.gov (United States)

    Burge, Matthew; Ringuette, Matthew

    2017-11-01

    We study the effect of pitching-phase on the circulation behavior for the 3D flow structures produced during stroke reversal for a 2-degree-of-freedom flapping wing executing hovering kinematics. Previous research has related the choice in pitching-phase with respect to the wing rotation during stroke reversal (advanced vs. symmetric pitch-timing) to a lift peak preceding stroke reversal. However, results from experiments on the time-varying circulation contributions from the 3D vortex structures across the span produced by both rotation and pitching are lacking. The objective of this research is to quantitatively examine how the spanwise circulation of these structures is affected by the pitching-phase for several reduced pitching frequencies. We employ a scaled wing model in a glycerin-water mixture and measure the time-varying velocity using multiple planes of stereo digital particle image velocimetry. Data-plane positions along the wing span are informed by the unsteady behavior of the 3D vortex structures found in our prior flow visualization movies. Individual vortices are identified to calculate their circulation. This work is aimed at understanding how the behavior of the vortex structures created during stroke reversal vary with key motion parameters. This work is supported by the National Science Foundation, Award Number 1336548, supervised by Dr. Ronald Joslin.

  16. Screening and characterization of a novel alkaline lipase from Acinetobacter calcoaceticus 1-7 isolated from Bohai Bay in China for detergent formulation

    Directory of Open Access Journals (Sweden)

    Haikuan Wang

    2012-03-01

    Full Text Available A novel alkaline lipase-producing strain 1-7 identified as Acinetobacter calcoaceticus was isolated from soil samples collected from Bohai Bay, China, using an olive oil alkaline plate, which contained olive oil as the sole carbon source. The lipase from strain 1-7 showed the maximum activity at pH 9.0 under 40ºC. One interesting feature of this enzyme is that it exhibits lipase activity over a broad range of temperatures and good stability. It is also stable at a broad range of pHs from 4.0 to 10.0 for 24 h. Its catalytic activity was highly enhanced in the presence of Ca2+, Mg2+ and K+, but partially inhibited by Cu2+, Al3+, Fe3+ , Ba2+and Zn2+. The fact that it displays marked stability and activity in the presence of TritonX-100, Tween-20, Tween-80, SDS, Hydrogen peroxide, Sodium perborate, Sodium hypochlorite, Sodium citrate, Sodium taurocholate, Glycerine and NaCl suggests that this lipase is suitable as an additive in detergent formulations.

  17. Evaluation of Two Commercially Available Cannabidiol Formulations for Use in Electronic Cigarettes.

    Science.gov (United States)

    Peace, Michelle R; Butler, Karen E; Wolf, Carl E; Poklis, Justin L; Poklis, Alphonse

    2016-01-01

    Since 24 states and the District of Columbia have legalized marijuana in some form, suppliers of legal marijuana have developed Cannabis sativa products for use in electronic cigarettes (e-cigarettes). Personal battery powered vaporizers, or e-cigarettes, were developed to deliver a nicotine vapor such that smokers could simulate smoking tobacco without the inherent pathology of inhaled tobacco smoke. The liquid formulations used in these devices are comprised of an active ingredient such as nicotine mixed with vegetable glycerin (VG) and/or propylene glycol (PG) and flavorings. A significant active ingredient of C. sativa, cannabidiol (CBD), has been purported to have anti-convulsant, anti-nociceptive, and anti-psychotic properties. These properties have potential medical therapies such as intervention of addictive behaviors, treatments for epilepsy, management of pain for cancer patients, and treatments for schizophrenia. However, CBD extracted from C. sativa remains a DEA Schedule I drug since it has not been approved by the FDA for medical purposes. Two commercially available e-cigarette liquid formulations reported to contain 3.3 mg/mL of CBD as the active ingredient were evaluated. These products are not regulated by the FDA in manufacturing or in labeling of the products and were found to contain 6.5 and 7.6 mg/mL of CBD in VG and PG with a variety of flavoring agents. Presently, while labeled as to content, the quality control of manufacturers and the relative safety of these products is uncertain.

  18. E-Cigarette use among children and young people: the need for regulation.

    Science.gov (United States)

    Wasowicz, Adam; Feleszko, Wojciech; Goniewicz, Maciej L

    2015-10-01

    Electronic cigarettes (e-cigarettes) are devices designed to deliver nicotine to the body via the route of inhalation. The principle of operation is based on heating a nicotine solution in propylene glycol and/or glycerine (e-liquid), turning it into aerosol (commonly called 'vapour'), which is then inhaled by the user. The scientific evidence on the health consequences of long-term e-cigarette use is sparse and currently inconclusive. Young people are the most vulnerable group to initiate use of e-cigarettes. The novelty of the e-cigarette, perceptions about the harmlessness of the product, a wide variety of flavours (fruit, chocolate, peanut butter, bubble gum, gummy bear, amongst others), and peer-influence are just a few examples of factors contributing to the e-cigarette popularity among youth. The comprehensive e-cigarette regulations need to include rules on marketing, safety of newly introduced products (nicotine dosage, packaging, and labelling), marketing limitations, and banning the sale of e-cigarettes to minors.

  19. Indium tin oxide refractometer in the visible and near infrared via lossy mode and surface plasmon resonances with Kretschmann configuration

    International Nuclear Information System (INIS)

    Torres, V.; Beruete, M.; Sánchez, P.; Del Villar, I.

    2016-01-01

    An indium tin oxide (ITO) refractometer based on the generation of lossy mode resonances (LMRs) and surface plasmon resonances (SPRs) is presented. Both LMRs and SPRs are excited, in a single setup, under grazing angle incidence with Kretschmann configuration in an ITO thin-film deposited on a glass slide. The sensing capabilities of the device are demonstrated using several solutions of glycerin and water with refractive indices ranging from 1.33 to 1.47. LMRs are excited in the visible range, from 617 nm to 682 nm under TE polarization and from 533 nm to 637 nm under TM polarization, with a maximum sensitivity of 700 nm/RIU and 1200 nm/RIU, respectively. For the SPRs, a sensing range between 1375 nm and 2494 nm with a maximum sensitivity of 8300 nm/RIU is measured under TM polarization. Experimental results are supported with numerical simulations based on a modification of the plane-wave method for a one-dimensional multilayer waveguide

  20. Quality Parameters and Chemical Analysis for Biodiesel Produced in the United States in 2011

    Energy Technology Data Exchange (ETDEWEB)

    Alleman, T. L.; Fouts, L.; Chupka, G.

    2013-03-01

    Samples of biodiesel (B100) from producers and terminals in 2011were tested for critical properties: free and total glycerin, flash point, cloud point, oxidation stability, cold soak filterability, and metals. Failure rates for cold soak filterability and oxidation stability were below 5%. One sample failed flash point due to excess methanol. One sample failed oxidation stability and metal content. Overall, 95% of the samples from this survey met biodiesel quality specification ASTM D6751. In 2007, a sampling of B100 from production facilities showed that nearly 90% met D6751. In samples meeting D6751, calcium was found above the method detection limit in nearly half the samples. Feedstock analysis revealed half the biodiesel was produced from soy and half was from mixed feedstocks. The saturated fatty acid methyl ester concentration of the B100 was compared to the saturated monoglyceride concentration as a percent of total monoglyceride. The real-world correlation of these properties was very good. The results of liquid chromatograph measurement of monoglycerides were compared to ASTM D6751. Agreement between the two methods was good, particularly for total monoglycerides and unsaturated monoglycerides. Because only very low levels of saturated monoglycerides measured, the two methods had more variability, but the correlation was still acceptable.

  1. Effect of formulation variables on the physical properties and stability of Dead Sea mud masks.

    Science.gov (United States)

    Shahin, Sawsan; Hamed, Saja; Alkhatib, Hatim S

    2015-01-01

    The physical stability of Dead Sea mud mask formulations under different conditions and their rheological properties were evaluated as a function of the type and level of thickeners, level of the humectant, incorporation of ethanol, and mode of mud treatment. Formulations were evaluated in terms of visual appearance, pH, moisture content, spreadability, extrudability, separation, rate of drying at 32 degrees C, and rheological properties. Prepared mud formulations and over-the-shelf products showed viscoplastic shear thinning behavior; satisfactory rheological behavior was observed with formulations containing a total concentration of thickeners less than 10% (w/w). Casson and Herschel-Bulkley models were found the most suitable to describe the rheological data of the prepared formulations. Thickener incorporation decreased phase separation and improved formulation stability. Bentonite incorporation in the mud prevented color changes during stability studies while glycerin improved spreadability. Addition of 5% (w/w) ethanol improved mud extrudability, slightly increased percent separation, accelerated drying at 32 degrees C, and decreased viscosity and yield stress values. Different mud treatment techniques did not cause a clear behavioral change in the final mud preparation. B10G and K5B5G were labeled as "best formulas" based on having satisfactory physical and aesthetic criteria investigated in this study, while other formulations failed in one or more of the tests we have performed.

  2. USING HOT WIRE TECHNIQUE FOR MEASURING THERMAL CONDUCTIVITY OF INFUSIONS OF ORGANIC AND CONVENTIONAL COFFEE

    Directory of Open Access Journals (Sweden)

    Fernando Gordillo-Delgado

    2016-07-01

    Full Text Available The technique of hot wire, a versatile method of low cost and high accuracy for measuring the thermal conductivity of fluids through the increasing temperature of a wire that is immersed into the liquid and between its ends a potential difference is abruptly applied. Using well-known conductivity liquids: water, ethylene glycol and glycerine, the system was tested and calibrated. In this work, this procedure was used to measure the thermal conductivity of the infusion samples of organic and conventional coffee. The same roast degree of the beans was verified with a colorimeter and the preparation was made by pressing 22g of coffee powder in 110mL of water. The obtained data were subjected to Analysis of Variance (ANOVA and this confirmed that the differences in the thermophysical parameter in the two samples are significant with a confidence level of 95\\%. On this way, it was proved that the thermal conductivity value of the coffee infusion allows differentiate between organic and conventional coffee.

  3. One-port portable SAW sensor system

    Science.gov (United States)

    Hoa Nguyen, Vu; Peters, Oliver; Schnakenberg, Uwe

    2018-01-01

    A portable device using the SAW-based impedance sensor type based on one interdigital transducer simultaneously as SAW generator and sensor element (1-port approach) is introduced. As a novelty, the so far required expensive vector network analyzer (VNA) is replaced by a hand-held device to measure the impedance spectrum of the SAW sensor by RF-gain-phase meters. Hence, some of the best features from the conventional oscillator and VNA approaches are combined to develop a low-cost and self-contained measurement system, including signal in- and output ability for real-time measurements. The pivotal aspect of the portable system is the transfer of the sophisticated high frequency approach into a quasi-static one. This enables the use of simple lumped electronics without the need of impedance matching circuits. Proof-of-concept was carried out by measuring conductivities of phosphate-buffered solutions and viscosities of glycerin. Sensitivities for temperature of 0.3%/°C, viscosity of 10.1% (mPa s)-1 and conductivity of 0.5% (S cm)-1 have been determined, respectively, which are competitive results compared to the benchmark approaches.

  4. Immunodiagnosis of Trypanosoma cruzi (Chagas' Disease Infection in Naturally Infected Dogs

    Directory of Open Access Journals (Sweden)

    Lauricella MA

    1998-01-01

    Full Text Available This study reports on the standardization of an enzyme-linked immunosorbent assay (ELISA for detecting specific antibodies anti-Trypanosoma cruzi in naturally infected dogs. Sera from 182 mongrel dogs of all ages residing in four rural villages in Santiago del Estero, Argentina, were collected in November 1994 and preserved in buffered neutral glycerin. All sera were tested by indirect hemagglutination test (IHAT, indirect immunofluorescence test (IFAT, and ELISA using the flagellar fraction of T. cruzi as antigen. Dog sera from an area without vectorial transmission were used to calculate ELISA specificity and cut-off value. Eighty-six percent of sera had concordant results for all tests. All sera reactive for IHAT and IFAT were also reactive for ELISA, except in one case. Sera tested by ELISA when diluted 1:200 allowed a clearer division between non-reactive and reactive sera than when 1:100 with greater agreement among serologic techniques. The specificity of ELISA was 96.2%. Among 34 adult dogs with a positive xenodiagnosis, sensitivity was 94% both for ELISA and IFAT. ELISA is the first choice for screening purposes and one of the pair of techniques recommended for diagnostic studies in dog populations

  5. Flow regime classification in air-magnetic fluid two-phase flow.

    Science.gov (United States)

    Kuwahara, T; De Vuyst, F; Yamaguchi, H

    2008-05-21

    A new experimental/numerical technique of classification of flow regimes (flow patterns) in air-magnetic fluid two-phase flow is proposed in the present paper. The proposed technique utilizes the electromagnetic induction to obtain time-series signals of the electromotive force, allowing us to make a non-contact measurement. Firstly, an experiment is carried out to obtain the time-series signals in a vertical upward air-magnetic fluid two-phase flow. The signals obtained are first treated using two kinds of wavelet transforms. The data sets treated are then used as input vectors for an artificial neural network (ANN) with supervised training. In the present study, flow regimes are classified into bubbly, slug, churn and annular flows, which are generally the main flow regimes. To validate the flow regimes, a visualization experiment is also performed with a glycerin solution that has roughly the same physical properties, i.e., kinetic viscosity and surface tension, as a magnetic fluid used in the present study. The flow regimes from the visualization are used as targets in an ANN and also used in the estimation of the accuracy of the present method. As a result, ANNs using radial basis functions are shown to be the most appropriate for the present classification of flow regimes, leading to small classification errors.

  6. Prevalence of Strongylida nematodes associated with African Snail, Achatina fulica, in Valle del Cauca, Colombia

    Directory of Open Access Journals (Sweden)

    Diego Córdoba-R

    2017-09-01

    Full Text Available Objectives. To establish the presence and prevalence of Strongylida nematode parasites in Achatina fulica in the Valle del Cauca, especially of nematodes that are potentially pathogenic for humans. Materials and methods. A. fulica individuals were collected in nine cities of the Valle del Cauca, Colombia. Direct visual examination was used to identify A. fulica parasites. Nematodes were separated from tissue or collected from mucus, washed in saline solution, and fixed in a hot AFA solution. Samples were mounted in glycerine and observed under the microscope. Results. The general nematode parasite prevalence was 35% in 2013. The city with highest prevalence during 2013 was Cartago (60%, following by Buenaventura (42.9% and Cali (33%, while during 2014 were Cali (30% and Buenaventura (30%. The Strongylida nematodes registered were classified in three genera: Angiostrongylus (14.7% prevalence, Aelurostrongylus (2.6%,and Strongyluris (2.6%. The city with highest positive records of Angiostrongylus was Cali during 2014 and Aelurostrongylus was Buenaventura during 2013. Strongyluris genus was recorded only in Cali during 2013, with a prevalence of 11%. Of the nine evaluated cities, five has presence of Angiostrongylus. Conclusions. Three genera of Strongylida nematode were recorded associated with A. fulicas specimens in the Valle del Cauca during 2013 and 2014. Therefore, the role that A. fulica and native mollusk species could be playing in the life cycle of these parasites at the local level should not underestimated.

  7. FY 2000 report on the results of the survey on the biomass-derived energy conversion technology. III; 2000 nendo biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation to the biomass-derived energy conversion technology which was regarded as promising from the results of the survey already made, the survey was made on the present situation and subjects of the technical development, social needs, energy efficiency, economical efficiency and the future. Studies were conducted on the development of technology for effective biomass utilization and the conceptual design and evaluation of a system for effective biomass utilization. As to the effective biomass utilization technology, the survey was made on the biomass combustion power generation technology/gasification power generation technology, gasification methanol synthesis of biomass, biomass gasification dimethyl ether synthesis, technology of ethanol production by alcohol fermentation via saccharification of biomass, methy-esterification of grease biomass, especially palm oil, and diesel oil production via reformation of by-product glycerin, and energy production from biomass using super- (sub- ) critical reaction. As to the system for effective biomass utilization, the survey was carried out of the regional outline, resource amount and sampling amount, selection of the conversion technology, and economical efficiency of Takatsuki city, Osaka, Shimokawa town, Hokkaido, Yufutsu/Hidaka region, Hokkaido, and Aogaki town, Hyogo. (NEDO)

  8. Extract of grapefruit-seed reduces acute pancreatitis induced by ischemia/reperfusion in rats: possible implication of tissue antioxidants.

    Science.gov (United States)

    Dembinski, A; Warzecha, Z; Konturek, S J; Ceranowicz, P; Dembinski, M; Pawlik, W W; Kusnierz-Cabala, B; Naskalski, J W

    2004-12-01

    Grapefruit seed extract (GSE) has been shown to exert antibacterial, antifungal and antioxidant activity possibly due to the presence of naringenin, the flavonoid with cytoprotective action on the gastric mucosa. No study so far has been undertaken to determine whether this GSE is also capable of preventing acute pancreatic damage induced by ischemia/reperfusion (I/R), which is known to result from reduction of anti-oxidative capability of pancreatic tissue, and whether its possible preventive effect involves an antioxidative action of this biocomponent. In this study carried out on rats with acute hemorrhagic pancreatitis induced by 30 min partial pancreatic ischemia followed by 6 h of reperfusion, the GSE or vehicle (vegetable glycerin) was applied intragastrically in gradually increasing amounts (50-500 microl) 30 min before I/R. Pretreatment with GSE decreased the extent of pancreatitis with maximal protective effect of GSE at the dose 250 microl. GSE reduced the pancreatitis-evoked increase in serum lipase and poly-C specific ribonuclease activity, and attenuated the marked fall in pancreatic blood flow and pancreatic DNA synthesis. GSE administered alone increased significantly pancreatic tissue content of lipid peroxidation products, malondialdehyde and 4-hydroxyalkens, and when administered before I/R, GSE reduced the pancreatitis-induced lipid peroxidation. We conclude that GSE exerts protective activity against I/R-induced pancreatitis probably due to the activation of antioxidative mechanisms in the pancreas and the improvement of pancreatic blood flow.

  9. Permeation of sumatriptan succinate across human skin using multiple types of self-dissolving microneedle arrays fabricated from sodium hyaluronate.

    Science.gov (United States)

    Wu, Dan; Katsumi, Hidemasa; Quan, Ying-Shu; Kamiyama, Fumio; Kusamori, Kosuke; Sakane, Toshiyasu; Yamamoto, Akira

    2016-09-01

    Available formulations of sumatriptan succinate (SS) have low bioavailability or are associated with site reactions. We developed various types of self-dissolving microneedle arrays (MNs) fabricated from sodium hyaluronate as a new delivery system for SS and evaluated their skin permeation and irritation in terms of clinical application. In vitro permeation studies with human skin, physicochemical properties (needle length, thickness and density), and penetration enhancers (glycerin, sodium dodecyl sulfate and lauric acid diethanolamide) were investigated. SS-loaded high-density MNs of 800 µm in length were the optimal formulation and met clinical therapeutic requirements. Penetration enhancers did not significantly affect permeation of SS from MNs. Optical coherence tomography images demonstrated that SS-loaded high-density MNs (800 µm) uniformly created drug permeation pathways for the delivery of SS into the skin. SS-loaded high-density MNs induced moderate primary skin irritations in rats, but the skin recovered within 72 h of removal of the MNs. These findings suggest that high-density MNs of 800 µm in length are an effective and promising formulation for transdermal delivery of SS. To our knowledge, this is the first report of SS permeation across human skin using self-dissolving MNs.

  10. Optimization of the process of methylic transesterification of palm oil an experimental plant in batches in RECOPE

    International Nuclear Information System (INIS)

    Delgado Quesada, Adrian

    2013-01-01

    The production process of biodiesel is optimized in the Laboratorio de Investigacion of RECOPE. A subprocess of raw material purification and finished product is implemented. Parameters of optimization for the experimental plant are established by a bibliographic search. Palm oil acquired by RECOPE is characterized. The optimization of the alkaline transesterification of palm oil with methanol is realized in the experimental plant of RECOPE, through a full factorial design of five variables on two levels: the effect of temperature, the relationship of catalyst-oil, the speed of agitation, the molar relationship alcohol-oil and the reaction time in the production of biodiesel. The operation optimal values of the experimental plant are obtained by ANOVA. The maximum quantity of soaps required is determined to saturate exchange resin used in the purification of the biodiesel. The parameters of optimum operating are proposed for the production process of methyl biodiesel of palm according to the conditions of the oil and in the test plant of RECOPE. The result of the analysis of control variables of the biodiesel as the density have been according to reported by the Reglamento Tecnico Centroamericano (RTCA). However, the measured variables to biodiesel as total glycerin, inflammability point, content of fatty acid methyl esters and acid number have indicated the necessity to implement pretreatment steps from the oil by acid esterification. Besides, the study has determined that biodiesel remains without comply with the standards established by the RTCA for its commercialization at national or international level [es

  11. Effect of heat bed temperature of 3D bioprinter to hardness and compressive strength of scaffold bovine hydroxyapatite

    Science.gov (United States)

    Triyono, Joko; Pratama, Aditya; Sukanto, Heru; Nugroho, Yohanes; Wijayanta, Agung Tri

    2018-02-01

    This study aimed to investigate the effect of heat bed temperature of 3D bioprinter toward compressive strength and hardness bovine bone hydroxyapatite scaffold for bone filler applications. BHA-glycerin mixed with a ratio of 1:1, and keep it for 24 hours. After the homogenization process acquired, bio-Ink with shaped slurry will be used as a material for a 3D printer. The printing process with a temperature variation have performed by setting up heat bed temperature. After printing process was completed, the 3D scaffold was detained on the heat bed for 10 minutes before being picked up. The test results in this study had the lowest hardness value of 9.82±0.62 VHN and the highest number of 24.32±0.99 VHN. The compressive strength testing had the lowest value of 1.62±0.16 MPa with the highest number of 5.67±0.39 MPa. Pore observation using a scanning electron microscope. The result shows that the size of the pores were not much different, that was ±100-200 µm. This observation also indicated that the pore form was square pores.

  12. Stability conditions of stationary rupture of liquid layers on an immiscible fluid surface

    Energy Technology Data Exchange (ETDEWEB)

    Viviani, A. [Seconda Univ. di Napoli, Aversa (Italy). Facolta di Ingegneria; Kostarev, K.; Shmyrov, A.; Zuev, A. [Inst. of Continuous Media Mechanics, Perm (Russian Federation)

    2009-07-01

    The stationary equilibrium shape of a 3-phase liquids-gas system was investigated. The system consisted of a horizontal liquid layer with an upper free boundary placed on the immiscible fluid interface. The study investigated the stability conditions of rupture of the liquid layer surface. The dependence of rupture parameters on the experimental cuvette diameter and layer thickness was investigated, as well as the difference in the values of surface tension of the examined fluids. The 2-layer system of horizontal fluid layers was formed in a glass cylindrical cuvette. The liquid substrate was tetrachloride carbon (CCI{sub 4}), while upper layers included water, glycerine, ethyleneglycol, and aqueous solutions of 1,4-butanediol C{sub 4}H{sub 10}O{sub 2} and isopropanol C{sub 3H8L}. Initially, the surface of the substrate fluid was overlaid with a horizontal liquid layer. The rupture was formed by subjecting the layer surface to short-time actions of a narrow directional air jet. After rupture formation, the layer thickness increased gradually. The measurements demonstrated that the rupture diameter depends on the initial thickness of the upper layer as well as the diameter of the cuvette, and the difference in the values of the surface tension of the examined fluids. Analysis of the experimental relationships indicated that the critical thickness of the breaking layer is a constant value for any specific pairs of fluids. 4 refs., 7 figs.

  13. Fabrication of Li{sub 2}TiO{sub 3} pebbles by a freeze drying process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sang-Jin, E-mail: lee@mokpo.ac.kr [Department of Advanced Materials Science and Engineering, Mokpo National University, Muan 534-729 (Korea, Republic of); Park, Yi-Hyun [National Fusion Research Institute, Daejeon 305-806 (Korea, Republic of); Yu, Min-Woo [Department of Advanced Materials Science and Engineering, Mokpo National University, Muan 534-729 (Korea, Republic of)

    2013-11-15

    Li{sub 2}TiO{sub 3} pebbles were successfully fabricated by using a freeze drying process. The Li{sub 2}TiO{sub 3} slurry was prepared using a commercial powder of particle size 0.5–1.5 μm and the pebble pre-form was prepared by dropping the slurry into liquid nitrogen through a syringe needle. The droplets were rapidly frozen, changing their morphology to spherical pebbles. The frozen pebbles were dried at −10 °C in vacuum. To make crack-free pebbles, some glycerin was employed in the slurry, and long drying time and a low vacuum condition were applied in the freeze drying process. In the process, the solid content in the slurry influenced the spheroidicity of the pebble green body. The dried pebbles were sintered at 1200 °C in an air atmosphere. The sintered pebbles showed almost 40% shrinkage. The sintered pebbles revealed a porous microstructure with a uniform pore distribution and the sintered pebbles were crushed under an average load of 50 N in a compressive strength test. In the present study, a freeze drying process for fabrication of spherical Li{sub 2}TiO{sub 3} pebbles is introduced. The processing parameters, such as solid content in the slurry and the conditions of freeze drying and sintering, are also examined.

  14. Fabrication of Li2TiO3 pebbles by a freeze drying process

    International Nuclear Information System (INIS)

    Lee, Sang-Jin; Park, Yi-Hyun; Yu, Min-Woo

    2013-01-01

    Li 2 TiO 3 pebbles were successfully fabricated by using a freeze drying process. The Li 2 TiO 3 slurry was prepared using a commercial powder of particle size 0.5–1.5 μm and the pebble pre-form was prepared by dropping the slurry into liquid nitrogen through a syringe needle. The droplets were rapidly frozen, changing their morphology to spherical pebbles. The frozen pebbles were dried at −10 °C in vacuum. To make crack-free pebbles, some glycerin was employed in the slurry, and long drying time and a low vacuum condition were applied in the freeze drying process. In the process, the solid content in the slurry influenced the spheroidicity of the pebble green body. The dried pebbles were sintered at 1200 °C in an air atmosphere. The sintered pebbles showed almost 40% shrinkage. The sintered pebbles revealed a porous microstructure with a uniform pore distribution and the sintered pebbles were crushed under an average load of 50 N in a compressive strength test. In the present study, a freeze drying process for fabrication of spherical Li 2 TiO 3 pebbles is introduced. The processing parameters, such as solid content in the slurry and the conditions of freeze drying and sintering, are also examined

  15. Biofilm community diversity after exposure to 0·4% stannous fluoride gels.

    Science.gov (United States)

    Reilly, C; Rasmussen, K; Selberg, T; Stevens, J; Jones, R S

    2014-12-01

    To test the effect of 0·4% stannous fluoride (SnF2 ) glycerine-based gels on specific portions of the bacterial community in both a clinical observational study and in vitro multispecies plaque-derived (MSPD) biofilm model. Potential changes to specific portions of the bacterial community were determined through the Human Oral Microbial Identification Microarray (HOMIM). Both the observational clinical study and the biofilm model showed that short-term use of 0·4% SnF2 gel has little effect on the bacterial community depicted by hierarchical cluster analysis. The amount of plaque accumulation on a subject's teeth, which was measured by plaque index scores, failed to show statistical significant changes over the two baselines or after treatment (P = 0·9928). The in vitro results were similar when examining the effect of 0·4% SnF2 gels on biofilm adherence through a crystal violet assay (P = 0·1157). The bacteria within the dental biofilms showed resilience in maintaining the overall community diversity after exposure to 0·4% SnF2 topical gels. The study supports that the immediate benefits of using 0·4% SnF2 gels in children may be strictly from fluoride ions inhibiting tooth demineralization rather than delivering substantial antimicrobial effects. © 2014 The Society for Applied Microbiology.

  16. Conférence Chevreul

    Directory of Open Access Journals (Sweden)

    Mouloungui Zéphirin

    2004-11-01

    Full Text Available In this study two major strategy of transformation of the vegetables substrate are exposed. The first approach is related to the study of the catalytic heterocyclisation of natural glycerin in the glycerol carbonate. The system glycerol/glycerol carbonate constitutes a reactional medium of synthon generation and chemical compounds with skelton of multipurpose glycerylic. Glycerol carbonate is a molecule of first generation of the glycerol, it is conceived in natural media as a new chemistry which makes it possible to reinject glycerol in existing or new industry from the orginal procedure by the way of chemical means. The second approach regards the oleaginous seeds, as substrate in vitro or as microreactor in vivo. This marks a technological breakage compared to the model and tradional process of prapartion of oleochemical bases. In this matter it seems possible to obtain the fatty acids, fatty esters, directly from the oleaginous seeds by interaction between lipids and functional enzymes. This quantitave experimental approach produces the free hydrophobic moity and guarantees the multifonctionnal oleophiles compounds from the renewable oleochemistry.

  17. Hot-melt sub- and outercoating combined with enteric aqueous coating to improve the stability of aspirin tablets

    Directory of Open Access Journals (Sweden)

    Xiuzhi Wang

    2017-05-01

    Full Text Available Aspirin is apt to hydrolyze. In order to improve its stability, a new method has been developed involving the application of hot-melt sub- and outercoating combined with enteric aqueous coating. The main aim was to investigate the influence of these factors on the stability of ASA and understand how they work. Satisfactory storage stability were obtained when the aspirin tablet core coated with Eudragit L30D55 film was combined with glycerin monostearate (GMS as an outercoat. Hygroscopicity testing indicated that the moisture penetrating into the tablet may result in a significant change in the physical properties of the coating film observed by scanning electron microscopy. Investigation of the compatibility between the drug and film excipients shows that the talc and methacrylic acid had a significant catalytic effect on ASA. A hypothesis was proposed that the hydrolysis of ASA enteric coated tablets (ASA-ECT was mostly concentrated in the internal film and the interfaces between the film and tablet core. In conclusion, hot-melt coating technology is an alternative to subcoating or outercoating. Also, GMS sub-coating was a better choice for forming a stable barrier between the tablet core and the polymer coating layer, and increases the structure and chemical stability.

  18. Frontal Cortex Transcriptome Analysis of Mice Exposed to Electronic Cigarettes During Early Life Stages

    Directory of Open Access Journals (Sweden)

    Dana E. Lauterstein

    2016-04-01

    Full Text Available Electronic cigarettes (e-cigarettes, battery-powered devices containing nicotine, glycerin, propylene glycol, flavorings, and other substances, are increasing in popularity. They pose a potential threat to the developing brain, as nicotine is a known neurotoxicant. We hypothesized that exposure to e-cigarettes during early life stages induce changes in central nervous system (CNS transcriptome associated with adverse neurobiological outcomes and long-term disease states. To test the hypothesis, pregnant C57BL/6 mice were exposed daily (via whole body inhalation throughout gestation (3 h/day; 5 days/week to aerosols produced from e-cigarettes either with nicotine (13–16 mg/mL or without nicotine; following birth, pups and dams were exposed together to e-cigarette aerosols throughout lactation beginning at postnatal day (PND 4–6 and using the same exposure conditions employed during gestational exposure. Following exposure, frontal cortex recovered from ~one-month-old male and female offspring were excised and analyzed for gene expression by RNA Sequencing (RNA-Seq. Comparisons between the treatment groups revealed that e-cigarette constituents other than nicotine might be partly responsible for the observed biological effects. Transcriptome alterations in both offspring sexes and treatment groups were all significantly associated with downstream adverse neurobiological outcomes. Results from this study demonstrate that e-cigarette exposure during early life alters CNS development potentially leading to chronic neuropathology.

  19. Profile of serum alkaline phosphatase after inoculation of mononuclear cells and bone morphogenetic protein in the repair of osteochondral defects in rabbits

    Directory of Open Access Journals (Sweden)

    Luiz Augusto de Souza

    2011-12-01

    Full Text Available In this study, serum alkaline phosphatase activity was measured in response to the repair of osteochondral defects in twenty-four New Zealand rabbits. The animals were divided into three groups: a control (GC, those treated with bone marrow mononuclear cells (GCM and those that received mononuclear cells with autologous bone morphogenetic protein (BMP + GCM. After exposing the trochlear groove of the left stifle joint, a wedge-shaped segment was removed. Later, the defect was filled with an osteochondral autograft preserved in 98% glycerin. For the GC group, only the bone graft was performed. For the GCM, in addition to the graft, 2x106 seed mononuclear cells were implanted. For the GCM + BMP, the same number of cells, associated with 1μg of bone morphogenetic protein, were intraarticularly administered. The osteoblastic response was measured by analyzing the serum alkaline phosphatase on day 0 (preoperative 3, 15, 30, and 45 after surgery, and by radiographic examinations. Analysis of variance in randomized blocks, factorial and Tukey’s test (p = 0.05 were made. The overall mean GCM was superior to the other groups and the highest rates were among the 15th and 45th days postoperatively. The discrepancy in values between individuals of the same group casts doubts on the veracity of the test.

  20. Neurorrafia do ramo bucal dorsal do nervo facial em coelhos com proteção de segmento intestinal alógeno

    Directory of Open Access Journals (Sweden)

    Camila Araújo Busnardo

    2009-06-01

    Full Text Available 18 rabbits, New Zealand, males, adults were used for clinical and histological evaluation of repair dorsal buccal branch of facial nerve after 15, 30 and 60 days postoperatively (PO. The animals were divided into two groups for transection and 10-0 nylon monofilament epineural suture of buccal branch. In animals in Group I, the nerve was coated with protection of jejunum allograft preserved in glycerin 98% and in group II was applied epineural suture. Both groups occurred the return of movement of the upper lip from the eighth week. There was infiltrated cellular and giant cells with fibrosis unsystematic and collagen fibers of the allograft jejunum joing to the connective tissue. At 15 and 30 days of PO, the distal nerve stumps of both groups were found with degeneration wallerian and in 60 days, regenerated fibers. The repair of the dorsal buccal branch of facial nerve with the allograft wasn't significantly different between the control rabbits as to the assessment of histological and functional recovery.