MODELACIÓN DEL EFECTO DE LA PODA Y RALEO SOBRE LAS DEFORMACIONES RESIDUALES LONGITUDINALES EN Eucalyptus globulus Labill.

OpenAIRE

Navarrete, Eduardo; Valenzuela, Carolina; Nutto, Leif

2016-01-01

RESUMEN Se estudió una plantación de Eucalyptus globulus ubicada en el sector precordillerano andino de la región del Bío Bío, Chile, con el objetivo de evaluar y modelar el efecto de la poda y raleo sobre las deformaciones residuales longitudinales (DRL). El lugar de estudio correspondió a un rodal de 12 años de edad, el cual fue intervenido a los 2 años y medio de establecido, donde se evaluaron distintas intensidades de poda (0% y 60% de la altura total) y densidades de raleo (1.600 árb·ha...

RECOVERY OF LOGGING RESIDUES THROUGH BALER ON FORWARDER: EXPERIENCE WITH Eucalyptus globulus IN CHILE

Directory of Open Access Journals (Sweden)

Eduardo Acuña

2018-05-01

Full Text Available ABSTRACT This study presents results of tests on the recovery of Eucalyptus globulus logging residues. Leftovers were packed with an ENFO-2002 baler on a forwarder, taking advantage of a cut-to-length harvesting system for two conditions of residual biomass, i.e., with and without bark. A continuous field study was carried out, controlling 16.4 scheduled hours in seven days. Delays in the operation stemmed mainly by the visits of the client company and supervision by phone. The baler had an average utilization capacity of 81% for both evaluated conditions and produced an average of 36.2 bales with and 22.2 bales without bark per productive area. An average dry biomass productivity of 5.85 and 5.46 Mg h-1 was reached for similar conditions of residual biomass. Significant differences emerged when the type of harvesting was compared to mean dry weight, between types of harvesting, and mean baling time. Thus, the presence of bark in the logging residues of E. globulus increases the productivity of the baler.

MODELACIÓN DEL EFECTO DE LA PODA Y RALEO SOBRE LAS DEFORMACIONES RESIDUALES LONGITUDINALES EN Eucalyptus globulus Labill.

Directory of Open Access Journals (Sweden)

Eduardo Navarrete

2016-01-01

Full Text Available RESUMEN Se estudió una plantación de Eucalyptus globulus ubicada en el sector precordillerano andino de la región del Bío Bío, Chile, c on el objetivo de evaluar y modelar el efecto de la poda y raleo sobre las deformaciones residuales longitudinales (DRL . El lugar de estudio correspondió a un rodal de 12 años de edad, el cual fue intervenido a los 2 años y medio de establecido, donde se evaluaron distintas intensidades de poda (0% y 60% de la altura total y densidades de raleo (1.600 árb·ha -1 (sin raleo y 800 árb·ha -1 . En cada tratamiento definido por la combinación de los dos niveles de poda y raleo, se estudió además, el efecto de la clase de copa (dominante, codominante e intermedia sobre el comportamiento de las DRL. En cada unidad de muestreo se registraron variables a nivel de árbol individual, estimando los parámetros de rodal más relevantes. Se muestreó un total de 36 árboles, midiéndose en cada uno de ellos las DRL a nivel del Dap con un extensómetro diseñado por el CIRAD-Forêt. Los resultados determinaron que la poda y raleo no afectaron significativamente el comportamiento de las DRL en Eucalyptus globulus ; en cambio, la clase de copa, tuvo un efecto altamente significativo sobre la variación de las deformaciones residuales, presentando los árboles dominantes mayores niveles de deformación que las clases de copa codominante e intermedia, respectivamente. El modelo de estimación incluyó como variables predictivas del comportamiento de las DRL , las expresiones logarítmicas del Dap y del inverso multiplicativo de la varianza de los radios de copa, además de la poda, presentando un R 2 de 0,44 y un EEE de 0,132.

Nitrogen-Fixing Bacteria in Eucalyptus globulus Plantations

Science.gov (United States)

da Silva, Marliane de Cássia Soares; Paula, Thiago de Almeida; Moreira, Bruno Coutinho; Carolino, Manuela; Cruz, Cristina; Bazzolli, Denise Mara Soares; Silva, Cynthia Canedo; Kasuya, Maria Catarina Megumi

2014-01-01

Eucalypt cultivation is an important economic activity worldwide. In Portugal, Eucalyptus globulus plantations account for one-third of the total forested area. The nutritional requirements of this crop have been well studied, and nitrogen (N) is one of the most important elements required for vegetal growth. N dynamics in soils are influenced by microorganisms, such as diazotrophic bacteria (DB) that are responsible for biological nitrogen fixation (BNF), so the aim of this study was to evaluate and identity the main groups of DB in E. globulus plantations. Samples of soil and root systems were collected in winter and summer from three different Portuguese regions (Penafiel, Gavião and Odemira). We observed that DB communities were affected by season, N fertilization and moisture. Furthermore Bradyrhizobium and Burkholderia were the most prevalent genera in these three regions. This is the first study describing the dynamic of these bacteria in E. globulus plantations, and these data will likely contribute to a better understanding of the nutritional requirements of eucalypt cultivation and associated organic matter turnover. PMID:25340502

Nitrogen-fixing bacteria in Eucalyptus globulus plantations.

Science.gov (United States)

da Silva, Marliane de Cássia Soares; Paula, Thiago de Almeida; Moreira, Bruno Coutinho; Carolino, Manuela; Cruz, Cristina; Bazzolli, Denise Mara Soares; Silva, Cynthia Canedo; Kasuya, Maria Catarina Megumi

2014-01-01

Eucalypt cultivation is an important economic activity worldwide. In Portugal, Eucalyptus globulus plantations account for one-third of the total forested area. The nutritional requirements of this crop have been well studied, and nitrogen (N) is one of the most important elements required for vegetal growth. N dynamics in soils are influenced by microorganisms, such as diazotrophic bacteria (DB) that are responsible for biological nitrogen fixation (BNF), so the aim of this study was to evaluate and identity the main groups of DB in E. globulus plantations. Samples of soil and root systems were collected in winter and summer from three different Portuguese regions (Penafiel, Gavião and Odemira). We observed that DB communities were affected by season, N fertilization and moisture. Furthermore Bradyrhizobium and Burkholderia were the most prevalent genera in these three regions. This is the first study describing the dynamic of these bacteria in E. globulus plantations, and these data will likely contribute to a better understanding of the nutritional requirements of eucalypt cultivation and associated organic matter turnover.

Nitrogen-fixing bacteria in Eucalyptus globulus plantations.

Directory of Open Access Journals (Sweden)

Marliane de Cássia Soares da Silva

Full Text Available Eucalypt cultivation is an important economic activity worldwide. In Portugal, Eucalyptus globulus plantations account for one-third of the total forested area. The nutritional requirements of this crop have been well studied, and nitrogen (N is one of the most important elements required for vegetal growth. N dynamics in soils are influenced by microorganisms, such as diazotrophic bacteria (DB that are responsible for biological nitrogen fixation (BNF, so the aim of this study was to evaluate and identity the main groups of DB in E. globulus plantations. Samples of soil and root systems were collected in winter and summer from three different Portuguese regions (Penafiel, Gavião and Odemira. We observed that DB communities were affected by season, N fertilization and moisture. Furthermore Bradyrhizobium and Burkholderia were the most prevalent genera in these three regions. This is the first study describing the dynamic of these bacteria in E. globulus plantations, and these data will likely contribute to a better understanding of the nutritional requirements of eucalypt cultivation and associated organic matter turnover.

Above-ground biomass production and allometric relations of Eucalyptus globulus Labill. coppice plantations along a chronosequence in the central highlands of Ethiopia

International Nuclear Information System (INIS)

Zewdie, Mulugeta; Olsson, Mats; Verwijst, Theo

2009-01-01

Eucalyptus plantations are extensively managed for wood production in the central highlands of Ethiopia. Nevertheless, little is known about their biomass (dry matter) production, partitioning and dynamics over time. Data from 10 different Eucalyptus globulus stands, with a plantation age ranging from 11 to 60 years and with a coppice-shoot age ranging from 1 to 9 years were collected and analyzed. Above-ground tree biomass of 7-10 sampled trees per stand was determined destructively. Dry weights of tree components (W c ; leaves, twigs, branches, stembark, and stemwood) and total above-ground biomass (W a ) were estimated as a function of diameter above stump (D), tree height (H) and a combination of these. The best fits were obtained, using combinations of D and H. When only one explanatory variable was used, D performed better than H. Total above-ground biomass was linearly related to coppice-shoot age. In contrast a negative relation was observed between the above-ground biomass production and total plantation age (number of cutting cycles). Total above-ground biomass increased from 11 t ha -1 at a stand age of 1 year to 153 t ha -1 at 9 years. The highest dry weight was allocated to stemwood and decreased in the following order: stemwood > leaves > stembark > twigs > branches. The equations developed in this study to estimate biomass components can be applied to other Eucalyptus plantations under the assumption that the populations being studied are similar with regard to density and tree size to those for which the relationships were developed

Above-ground biomass production and allometric relations of Eucalyptus globulus Labill. coppice plantations along a chronosequence in the central highlands of Ethiopia

Energy Technology Data Exchange (ETDEWEB)

Zewdie, Mulugeta; Olsson, Mats; Verwijst, Theo [Swedish University of Agricultural Sciences, Department of Crop Production Ecology, P.O. Box 7043, 75007 Uppsala (Sweden)

2009-03-15

Eucalyptus plantations are extensively managed for wood production in the central highlands of Ethiopia. Nevertheless, little is known about their biomass (dry matter) production, partitioning and dynamics over time. Data from 10 different Eucalyptus globulus stands, with a plantation age ranging from 11 to 60 years and with a coppice-shoot age ranging from 1 to 9 years were collected and analyzed. Above-ground tree biomass of 7-10 sampled trees per stand was determined destructively. Dry weights of tree components (W{sub c}; leaves, twigs, branches, stembark, and stemwood) and total above-ground biomass (W{sub a}) were estimated as a function of diameter above stump (D), tree height (H) and a combination of these. The best fits were obtained, using combinations of D and H. When only one explanatory variable was used, D performed better than H. Total above-ground biomass was linearly related to coppice-shoot age. In contrast a negative relation was observed between the above-ground biomass production and total plantation age (number of cutting cycles). Total above-ground biomass increased from 11 t ha{sup -1} at a stand age of 1 year to 153 t ha{sup -1} at 9 years. The highest dry weight was allocated to stemwood and decreased in the following order: stemwood > leaves > stembark > twigs > branches. The equations developed in this study to estimate biomass components can be applied to other Eucalyptus plantations under the assumption that the populations being studied are similar with regard to density and tree size to those for which the relationships were developed. (author)

Physiological and biochemical responses to severe drought stress of nine Eucalyptus globulus clones: a multivariate approach.

Science.gov (United States)

Granda, Víctor; Delatorre, Carolina; Cuesta, Candela; Centeno, María L; Fernández, Belén; Rodríguez, Ana; Feito, Isabel

2014-07-01

Seasonal drought, typical of temperate and Mediterranean environments, creates problems in establishing plantations and affects development and yield, and it has been widely studied in numerous species. Forestry fast-growing species such as Eucalyptus spp. are an important resource in such environments, selected clones being generally used for production purposes in plantations in these areas. However, use of mono-specific plantations increases risk of plant loss due to abiotic stresses, making it essential to understand differences in an individual clone's physiological responses to drought stress. In order to study clonal differences in drought responses, nine Eucalyptus globulus (Labill.) clones (C14, C46, C97, C120, C222, C371, C405, C491 and C601) were gradually subjected to severe drought stress (<14% of field capacity). A total of 31 parameters, physiological (e.g., photosynthesis, gas exchange), biochemical (e.g., chlorophyll content) and hormonal (abscisic acid [ABA] content), were analysed by classic and multivariate techniques. Relationships between parameters were established, allowing related measurements to be grouped into functional units (pigment, growth, water and ABA). Differences in these units showed that there were two distinct groups of E. globulus clones on the basis of their different strategies when faced with drought stress. The C14 group (C14, C120, C405, C491 and C601) clones behave as water savers, maintaining high water content and showing high stomatal adjustment, and reducing their aerial growth to a great extent. The C46 group (C46, C97, C222 and C371) clones behave as water spenders, reducing their water content drastically and presenting osmotic adjustment. The latter maintains the highest growth rate under the conditions tested. The method presented here can be used to identify appropriate E. globulus clones for drought environments, facilitating the selection of material for production and repopulation environments. © The

Phytoremediation efficiency OF CD by Eucalyptus globulus transplanted from polluted and unpolluted sites.

Science.gov (United States)

Luo, Jie; Qi, Shihua; Peng, Li; Wang, Jinji

2016-01-01

The capacity of plants to uptake heavy metals from contaminated soils has shown great phytoremediation potential. The development, resistibility and Cd extraction of Eucalyptus globulus individuals from metalliferous and clean sites in different years were analyzed under a specific environment. Eucalyptus globulus planted in Guiyu for phytoremediation or cultivated in an uncontaminated, natural environment for economic purposes were transplanted to Yuecheng town, which, in recent years, has been involved in the e-waste dismantling and recycling business, to compare the phytoremediation efficiency of Eucalyptus globulus trees grown in different environments. Trees cultivated in polluted areas can remove far more Cd and Hg from the contaminated soil than the individuals from clean soils because metalliferous Eucalyptus globulus can produce more biomass and uptake more heavy metals than nonmetalliferous plants per year. As polluted environments negatively affect the growth of plants, we speculated that the phytoremediation efficiency of metalliferous Eucalyptus globulus should decrease over time and that nonmetalliferous trees should adapt to the local environment.

A NEW SPECIES OF INVASIVE GALL WASP (HYMENOPTERA: EULOPHIDAE: TETRASTICHINAE) ON BLUE GUM (EUCALYPTUS GLOBULUS) IN CALIFORNIA

Science.gov (United States)

The blue gum gall wasp, Selitrichodes globulus La Salle & Gates (Hymenoptera: Eulophidae: Tetrastichinae), is described as an invasive gall inducer on blue gum, Eucalyptus globulus (Myrtaceae), in California....

Linking photosynthesis and leaf N allocation under future elevated CO2 and climate warming in Eucalyptus globulus

Science.gov (United States)

Sharwood, Robert E.; Crous, Kristine Y.; Whitney, Spencer M.; Ellsworth, David S.

2017-01-01

Abstract Leaf-level photosynthetic processes and their environmental dependencies are critical for estimating CO2 uptake from the atmosphere. These estimates use biochemical-based models of photosynthesis that require accurate Rubisco kinetics. We investigated the effects of canopy position, elevated atmospheric CO2 [eC; ambient CO2 (aC)+240 ppm] and elevated air temperature (eT; ambient temperature (aT)+3 °C) on Rubisco content and activity together with the relationship between leaf N and Vcmax (maximal Rubisco carboxylation rate) of 7 m tall, soil-grown Eucalyptus globulus trees. The kinetics of E. globulus and tobacco Rubisco at 25 °C were similar. In vitro estimates of Vcmax derived from measures of E. globulus Rubisco content and kinetics were consistent, although slightly lower, than the in vivo rates extrapolated from gas exchange. In E. globulus, the fraction of N invested in Rubisco was substantially lower than for crop species and varied with treatments. Photosynthetic acclimation of E. globulus leaves to eC was underpinned by reduced leaf N and Rubisco contents; the opposite occurred in response to eT coinciding with growth resumption in spring. Our findings highlight the adaptive capacity of this key forest species to allocate leaf N flexibly to Rubisco and other photosynthetic proteins across differing canopy positions in response to future, warmer and elevated [CO2] climates. PMID:28064178

Eucalyptus globulus extract protects against UVB-induced photoaging by enhancing collagen synthesis via regulation of TGF-β/Smad signals and attenuation of AP-1.

Science.gov (United States)

Park, Bom; Hwang, Eunson; Seo, Seul A; Cho, Jin-Gyeong; Yang, Jung-Eun; Yi, Tae-Hoo

2018-01-01

UV irradiation triggers the overproduction of matrix metalloproteinases and collagen degradation, which in turn causes increased pigmentation, dryness, and deep wrinkling of the skin. These chronic symptoms are collectively referred to as photoaging. Eucalyptus globulus is an evergreen tree that is widely used in cosmetics because of its antimicrobial activity. In this study, we investigated the protective effect of 50% ethanol extracts of Eucalyptus globulus on UV-induced photoaging in vitro and in vivo. Normal human dermal fibroblasts were treated with Eucalyptus globulus at concentrations ranging from 1 to 100 μg/mL after UVB or non-UVB irradiation. We found that Eucalyptus globulus suppressed the expression of MMPs and IL-6, but increased the expression of TGF-β1 and procollagen type 1. In addition, Eucalyptus globulus inhibited activation of the AP-1 transcription factor, an inducer of MMPs. Eucalyptus globulus was also found to regulate TGF-β/Smad signaling by reversing the activity of negative Smad regulators. Lastly, in vivo studies showed that topical application of Eucalyptus globulus on UVB-irradiated hairless mice reduced wrinkle formation and dryness by down-regulating MMP-1 and up-regulating expression of elastin, TGF-β1, and procollagen type 1. Taken together, these data suggest that Eucalyptus globulus may be a useful agent in cosmetic products. Copyright © 2017 Elsevier Inc. All rights reserved.

The Role of Eucalyptus Globulus Forest and Products in Carbon Sequestration

International Nuclear Information System (INIS)

Arroja, L.; Dias, A.C.; Capela, I.

2006-01-01

This study is a contribution to the ongoing debate about the selection of the approach for carbon accounting in wood products to be used, in the future, in the national greenhouse gas inventories under the UNFCCC (United Nations Framework Convention on Climate Change). Two accounting approaches are used in this analysis: the stock-change approach and the atmospheric-flow approach. They are applied to the Portuguese Eucalyptus globulus forest sector. To achieve this objective, the fluxes of wood removed from the forest are tracked through its life cycle, which includes products manufacture (mainly pulp and paper), use and final disposal (landfilling, incineration and composting). This study develops a framework to the estimation of carbon sequestration in the forest of E. globulus, a fast growing species, more specifically, in the calculation of the conversion factors such as bark and foliage percentages and densities, used to convert wood volumes into total biomass. A mass balance approach based on real data from mills is also proposed, in order to assess carbon emissions from wood processing. The results show that E. globulus forest sector was a carbon sink, but the magnitude of the carbon sequestration differs substantially depending on the accounting approach used. The contribution of the forest ecosystem was smaller than the aggregated contribution of wood products in use and in landfills (including industrial waste), which reinforces the role that wood products play in national carbon budgets

Fungi associated to bark lesions of Eucalyptus globulus stems in plantations from Uruguay Fungos asociados as lesões da casca do caule de Eucalyptus globulus em plantações no uruguai

Directory of Open Access Journals (Sweden)

Raquel Alonso

2009-08-01

Full Text Available Trees with stem bark lesions are frequently observed in Eucalyptus globulus Labill. plantations, particularly in the central west region of Uruguay. These lesions constitute a problem for trunk decortications at harvest and they also facilitate the access of fungi that could cause wood decay. Seven, three and oneyear-old plantations, located at three sites in close proximity were selected. Four types of trunk lesions were present in trees regardless the age of plantation and more than one type was found in each plantation. The aim of this study was to investigate the fungal composition associated with these lesions and compare them to healthy tissues and try to find out the origin of these symptoms. Another purpose was to elucidate the real role of the fungi considered pathogens by means of experimental inoculations. Segments from lesions and healthy tissues yielded 897 fungal isolates belonging to 32 taxa, 681 isolates from bark lesions and 216 from healthy tissues. Both healthy and symptomatic tissues showed similar fungal species composition, but with differences in frequencies of colonization. Cytospora eucalypticola Van der Westhuizen, Botryosphaeria spp., Pestalotiopsis guepinii (Desm. Stey. and Penicillium spp. were the dominant species isolated. As symptoms were not reproduced after experimental inoculation with Botryosphaeria ribis Grossenb. & Duggar and B. eucalyptorum Crous, & M.J. Wingf, it could be suggested that these lesions were originated by unfavorable environmental conditions. The frost that occurred for several days out of season and flooding may have been involved in the development of bark lesion.As lesões na casca de Eucalyptus globulus Labill. são frequentemente observadas nas plantações da Região Centro-Oeste do Uruguai. Constituem problema para o descortiçamento na colheita e, além disso, facilita a penetraçao de fungos apodrecedores da madeira. Selecionaram-se plantações com 1, 3 e 7 anos de idade, em tr

Adaptación de la madera de Eucalyptus globulus a la normativa europea de durabilidad natural

OpenAIRE

Lorenzo, D.; Troya, M. T. de,; Baso, Carlos; Touza, M.; Prieto, M.J.

2007-01-01

La madera de Eucalyptus globulus en algunos países como Australia es recomendada para situaciones de riesgo de ataque de organismos xilófagos por su elevada durabilidad. En Galicia esta madera ha sido utilizada desde hace muchas décadas en estructuras y carpinterías, que aún hoy perduran. Sin embargo, la norma europea EN-350-2 encuadra la especie E. globulus en la peor categoría de durabilidad natural, situación que no se corresponde con la realidad. El objetivo de este proyecto es constatar ...

Labile and Non-labile Soil Carbon Fractions Equally Contributed to Carbon Changes under Long-term Fertilization

Science.gov (United States)

Liang, F.; Li, J.; Xu, M.; Huang, S.

2017-12-01

Soil organic carbon (SOC) storages are altered under long-term fertilization in croplands, it however remains unclear how fast- to slow-cycling SOC fractions each respond to fertilization practices. Based on five two-decade Chinese long-term fertilization experiments (GZL: Gongzhuling; ZZ: Zhengzhou; CQ: Chongqing; JX: Jinxian; QY: Qiyang) under three fertilization treatments (CK: cropping with no fertilizer input; NPK: chemical nitrogen, phosphorus and potassium fertilizers; and NPKM: NPK with manure input), we quantified very labile, labile, non-labile and total SOC stocks at 0-20cm soil depth. Results showed that SOC stocks varied among sites (GZL, JX, CQ > ZZ, QY) and generally increased with fertilizations (CK-1 at ZZ, GZL, QY, CQ and JX, respectively. The corresponding changes of the sum of very labile and labile SOC fractions were 2.6, 2.0, 1.8, 0.8 and -0.5 Mg ha-1 at ZZ, QY, GZL, CQ and JX, respectively. Also, NPKM increased total SOC stock by 18.3, 16.2, 14.4, 10.5, and 6.5 Mg ha-1 at QY, GZL, ZZ, CQ and JX, respectively. The corresponding changes of the sum of very labile and labile SOC fractions were 8.6, 6.8, 6.6, 3.2 and -1.6 Mg ha-1 at QY, GZL, ZZ, CQ and JX, respectively. These results suggested that about half or more than half SOC stock accretions under fertilization were induced by increase in non-labile SOC fractions. It thus informs the importance of non-labile SOC fractions in contributing to soil C sequestration under long-term fertilizations in Chinese croplands. Future research should improve our mechanistic understanding of biogeochemical transformation of non-labile organic C in soils.

Development of an acetic acid tolerant Spathaspora passalidarum strain through evolutionary engineering with resistance to inhibitors compounds of autohydrolysate of Eucalyptus globulus

DEFF Research Database (Denmark)

Morales, Paulina; Gentina, Juan Carlos; Aroca, German

2017-01-01

-fold higher than those obtained with the native strain, respectively. Inhibitors composition present inEucalyptus globulus autohydrolysate were (g L−1): acetic acid, 4.7; furfural, 1.0; HMF, 0.36; formic acid, 0.6;syringaldehyde, 0.14 and vanillin, 0.017. When Eucalyptus globulus autohydrolysate...

Managing for water-use efficient wood production in Eucalyptus globulus plantations

Science.gov (United States)

Donald A. White; John F. McGrath; Michael G. Ryan; Michael Battaglia; Daniel S. Mendham; Joe Kinal; Geoffrey M. Downes; D. Stuart Crombie; Mark E. Hunt

2014-01-01

This paper tests the hypothesis that thinning and nitrogen fertiliser can increase the mass of wood produced per volume of water used (evapotranspiration) by plantations of Eucalyptus globulus. We have called this plantation water productivity (PWPWOOD) and argue that, for a given genotype, this term integrates the effects of management, site and climate on both...

Energy evaluation of the Eucalyptus globulus and the Eucalyptus nitens in the north of Spain (Cantabria)

International Nuclear Information System (INIS)

Perez, S.; Renedo, C.J.; Ortiz, A.; Manana, M.; Silio, D.

2006-01-01

This work studied the potential use of the waste from Eucalyptus globulus and Eucalyptus nitens as energy crops, evaluating young and adult stages of both in all four seasons of the year with different moisture contents. The study was carried out made in Cantabria (North coast of Spain), located at latitude 43 o 28'N, and longitude 3 o 48'W. In this region, 29,513ha are dedicated to the growth of Eucalyptus, with about 80% E. globulus, and 20% E. nitens. Six different plantations have been analyzed and their bioclimatic diagrams determined. After the collection of samples the potential energy of every sample was obtained, they were weighed, analyzed and burned, giving a mean net calorific value of 17,384 and 17,927kJ/kg in the adult stage of E. globulus and E. nitens, respectively. The results for the young stage of both species were 17,708 and 18,670kJ/kg. Moisture content in the samples has a great influence on power production. Finally, the economic and environmental consequences of these crop species for the region of Cantabria were analyzed. (author)

Biologically labile photoproducts from riverine non-labile dissolved organic carbon in the coastal waters

Science.gov (United States)

Kasurinen, V.; Aarnos, H.; Vähätalo, A.

2015-06-01

In order to assess the production of biologically labile photoproducts (BLPs) from non-labile riverine dissolved organic carbon (DOC), we collected water samples from ten major rivers, removed labile DOC and mixed the residual non-labile DOC with artificial seawater for microbial and photochemical experiments. Bacteria grew on non-labile DOC with a growth efficiency of 11.5% (mean; range from 3.6 to 15.3%). Simulated solar radiation transformed a part of non-labile DOC into BLPs, which stimulated bacterial respiration and production, but did not change bacterial growth efficiency (BGE) compared to the non-irradiated dark controls. In the irradiated water samples, the amount of BLPs stimulating bacterial production depended on the photochemical bleaching of chromophoric dissolved organic matter (CDOM). The apparent quantum yields for BLPs supporting bacterial production ranged from 9.5 to 76 (mean 39) (μmol C mol photons-1) at 330 nm. The corresponding values for BLPs supporting bacterial respiration ranged from 57 to 1204 (mean 320) (μmol C mol photons-1). According to the calculations based on spectral apparent quantum yields and local solar radiation, the annual production of BLPs ranged from 21 (St. Lawrence) to 584 (Yangtze) mmol C m-2 yr-1 in the plumes of the examined rivers. Complete photobleaching of riverine CDOM in the coastal ocean was estimated to produce 10.7 Mt C BLPs yr-1 from the rivers examined in this study and globally 38 Mt yr-1 (15% of riverine DOC flux from all rivers), which support 4.1 Mt yr-1 of bacterial production and 33.9 Mt yr-1 bacterial respiration.

VEGETATION OF CHENCHA HIGHLANDS IN SOUTHERN ETHIOPIA

African Journals Online (AJOL)

ADMIN

inter alia, by environmental factors including soil properties, slope and aspect which varied significantly .... species percentage cover in each community, families and growth form and life form of each species are ..... Eucalyptus globulus Labill.

Mycosphaerella and Teratosphaeria species associated with Mycosphaerella Leaf Disease on Eucalyptus globulus in Portugal

Energy Technology Data Exchange (ETDEWEB)

Silva, M. C.; Machado, H. N.; Neves, L.; Araujo, C.; Phillips, J. L.

2012-11-01

Plantations of Eucalyptus globulus represent the main source of wood for the pulp and paper industry in Portugal and are affected by the complex of Mycosphaerella and Teratosphaeria species (Mycosphaerella leaf disease), which is an important foliage disease worldwide. This disease affect mainly young trees with juvenile-phase foliage, causing premature defoliation, decreased growth and wood production. Species of Mycosphaerella sensu lato reported on eucalypts in Portugal are M. communis, M. heimii, M. lateralis, M. madeirae, M. marksii M. walkeri, T. africana, T. molleriana, T. nubilosa and T. parva. In order to complete the survey, symptomatic leaves were collected from Eucalyptus globulus plantations. Morphological and molecular characterization was used to give an indication of the species occurrence and most frequent species (T. nubilosa) and the composition of the MLD complex that did not change after the latest review. (Author) 28 refs.

Ecophysiological responses of a young blue gum (Eucalyptus globulus) plantation to weed control.

Science.gov (United States)

Eyles, Alieta; Worledge, Dale; Sands, Peter; Ottenschlaeger, Maria L; Paterson, Steve C; Mendham, Daniel; O'Grady, Anthony P

2012-08-01

Early weed control may improve the growth of forest plantations by influencing soil water and nutrient availability. To understand eucalypt growth responses to weed control, we examined the temporal responses of leaf gas-exchange, leaf nitrogen concentration (N) and water status of 7-month-old Eucalyptus globulus L. trees in a paired-plot field trial. In addition, we monitored the growth, leaf N and water status of the competing vegetation in the weed treatment. By the end of the 11-month experiment, complete weed control (WF treatment) of largely woody competitors increased the basal diameter of E. globulus by 14%. As indicated by pre-dawn water potentials of > - 0.05 MPa, interspecies competition for water resources was minimal at this site. In contrast, competition for N appeared to be the major factor limiting growth. Estimations of total plot leaf N (g m(-2) ground) showed that competing vegetation accounted for up to 70% of the total leaf N at the start of the trial. This value fell to 15% by the end of the trial. Despite increased leaf N(area) in WF trees 5 months after imposition of weed control, the photosynthetic capacity (A(1500)) of E. globulus was unaffected by treatment suggesting that the growth gains from weed control were largely unrelated to changes in leaf-level photosynthesis. Increased nutrient availability brought about by weed control enabled trees to increase investment into leaf-area production. Estimates of whole-tree carbon budget based on direct measurements of dark respiration and A(1500) allowed us to clearly demonstrate the importance of leaf area driving greater productivity following early weed control in a nutrient-limited site.

Resource Communication. Temporal optimization of fuel treatment design in blue gum (Eucalyptus globulus) plantations

Energy Technology Data Exchange (ETDEWEB)

Martin, A.; Botequim, B.; Oliveira, T.M.; Ager, A.; Pirotti, F.

2016-07-01

Aim of the study: This study was conducted to support fire and forest management planning in eucalypt plantations based on economic, ecological and fire prevention criteria, with a focus on strategic prioritisation of fuel treatments over time. The central objective was to strategically locate fuel treatments to minimise losses from wildfire while meeting budget constraints and demands for wood supply for the pulp industry and conserving carbon. Area of study: The study area was located in Serra do Socorro (Torres Vedras, Portugal, covering ~1449 ha) of predominantly Eucalyptus globulus Labill forests managedcultivated for pulpwood by The Navigator Company. Material and methods: At each of four temporal stages (2015-2018-2021-2024) we simulated: (1) surface and canopy fuels, timber volume (m3 ha-1) and carbon storage (Mg ha-1); (2) fire behaviour characteristics, i.e. rate of spread (m min-1), and flame length (m), with FlamMap fire modelling software; (3) optimal treatment locations as determined by the Landscape Treatment Designer (LTD). Main results: The higher pressure of fire behaviour in the earlier stages of the study period triggered most of the spatial fuel treatments within eucalypt plantations in a juvenile stage. At later stages fuel treatments also included shrublands areas. The results were consistent with observations and simulation results that show high fire hazard in juvenile eucalypt stands. Research highlights: Forest management planning in commercial eucalypt plantations can potentially accomplish multiple objectives such as augmenting profits and sustaining ecological assets while reducing wildfire risk at landscape scale. However, limitations of simulation models including FlamMap and LTD are important to recognise in studies of long term wildfire management strategies. (Author)

Acaricidal and repellent activities of essential oil of Eucalyptus globulus against Dermanyssus gallinae (Acari: Mesostigmata

Directory of Open Access Journals (Sweden)

Dehghani-Samani Amir

2015-07-01

Full Text Available Introduction: By considering an increase in drug resistance against red mites, finding the nonchemical herbal acaricide against Dermanyssus gallinae (De Geer (Acari: Mesostigmata is necessary to kill them and to reduce the chemical resistance against chemical acaricides in this specie. Dermanyssus gallinae is a potential vector of the causal agent of several viral diseases such as Equine encephalitis and St. Louis encephalitis. It can be a vector of bacteria such as Salmonella spp., Mycobacterium spp. and Erysipelothrix rhusiopathiae. It is also known to cause itching dermatosis in humans. In this study acaricidal and repellent activities of essential oil of Eucalyptus globulus against Dermanyssus gallinae were studied. Methods: After extracting the essential oil, different concentrations of the plant extract were prepared. Then, acaricidal effect of different concentrations was tested on poultry red mite, Dermanyssus gallinae, by dropping 3-4 drops of essential oil on mites. Repellent activity of essential oil was tested by Y-tube olfactometer bioassay. After the test, total number of killed and repellent mites reported. Results: Concentration of 1:2 or 50% had more acaricidal effect on mites. Also essential oil of Eucalyptus globulus had repellent activity against red mites. Conclusion: This study showed that essential oil of Eucalyptus globulus had acaricidal and repellent activities against red mites. Hence it might be used as a herbal acaricide against it to kill and to reduce the chemical resistance in this specie.

A model for predicting the growth of Eucalyptus globulus seedling stands in Bolivia

Energy Technology Data Exchange (ETDEWEB)

Guzman, G.; Morales, M.; Pukkala, T.; Miguel, S. de

2012-11-01

Eucalyptus globulus is one of the most planted species in the Inter-Andean Valleys of Bolivia, where growing conditions are different from most places where eucalyptus have been studied. This prevents a straightforward utilization of models fitted elsewhere. In this study a distance-independent individual-tree growth model for E. globulus plantations in Bolivia was developed based on data from 67 permanent sample plots. The model consists of sub-models for dominant height, tree diameter increment, height-diameter relationship and survival. According to model-based simulations, the mean annual increment with the optimal rotation length is about 13 m3 ha{sup -}1 yr{sup -}1 on medium-quality sites and 18 m{sup 3} ha{sup -}1 yr -1 on the best sites. A suitable rotation length for maximizing wood production is approximately 30 years on medium sites and 20 years on the most productive sites. The developed models provide valuable information for further studies on optimizing the management and evaluating alternative management regimes for the species. (Author) 22 refs.

Mycosphaerella and Teratosphaeria species associated with leaf diseases on Eucalyptus globulus in southern Brazil

NARCIS (Netherlands)

Teodoro, M.G.; Ferreira, M.A.; Guimarães, L.M.S.; Mafia, R.G.; Groenewald, J.Z.; Crous, P.W.; Alfenas, A.C.

2012-01-01

Leaf blight and defoliation caused by Teratosphaeria species is one of the most important leaf diseases of Eucalyptus globulus. Due to the importance of this tree species for the production of pulp and paper, and recent reports of severe leaf disease symptoms in Brazil, the present study was

Torrefaction of wood and bark from Eucalyptus globulus and Eucalyptus nitens: Focus on volatile evolution vs feasible temperatures

International Nuclear Information System (INIS)

Arteaga-Pérez, Luis E.; Segura, Cristina; Bustamante-García, Verónica; Gómez Cápiro, Oscar; Jiménez, Romel

2015-01-01

Torrefaction is a thermal pretreatment leading to the improvement of most of the fuel properties of biomass, namely energy density, HHV (higher heating value), grindability and hydrophobicity. The aim of this study is to identify the most feasible temperature to carry out torrefaction of Eucalyptus globulus and nitens, based on chemical evidences associated to the release of volatiles during thermal treatment of biomass. With that end: (i) Devolatilization kinetics, (ii) Effects of temperature and residence time and (iii) volatiles composition during torrefaction of both wood and bark were analyzed. In all cases DTG (derivative thermogravimetric curves) exhibited the typical shape of lignocellulosic materials, with three decomposition phases and two reaction zones. Values of activation energies for hemicellulose decomposition, were in agreement with those reported in the literature (121–170 kJ/mol). Carboxylic acids, water and phenolic compounds showed two peaks, which were associated to torrefaction (below 310 °C) and pyrolysis (310–410 °C) respectively. The most feasible temperatures for torrefaction were estimated as a function of these peaks, and it ranged between 295 °C and 310°C for all samples. Main volatile species at the torrefaction peaks were distributed as Water > Acetic Acid > CO_2 > Others, while Levoglucosan formation was marginal, due to the catalytic effect of inorganics. - Highlights: • Identification of torrefaction peaks for E. globulus and E. nitens using dynamic TGA-MS. • Devolatilization kinetics of E. globulus and E. nitens (wood and bark). • Effect of operation parameters on torrefaction of E. globulus and E. nitens. • Most feasible temperatures for torrefaction based on chemical and thermal evidences. • Definition of atomic indicator to estimate degradation degree based on TGA-MS.

Comparison of Fractionation Techniques of CO2 Extracts from Eucalyptus Globulus - Composition and Insecticidal Activity

Czech Academy of Sciences Publication Activity Database

Topiař, Martin; Sajfrtová, Marie; Pavela, R.; Machalová, Zdeňka

2015-01-01

Roč. 97, FEB 2015 (2015), s. 202-210 ISSN 0896-8446 R&D Projects: GA TA ČR TA01010578 Institutional support: RVO:67985858 Keywords : supercritical fractinacion * eucalyptus globulus * insecticidal activity Subject RIV: CI - Industrial Chemistry , Chemical Engineering Impact factor: 2.579, year: 2015

A model system to study the lignification process in Eucalyptus globulus.

Science.gov (United States)

Araújo, Pedro; Cesarino, Igor; Mayer, Juliana Lischka Sampaio; Ferrari, Ilse Fernanda; Kiyota, Eduardo; Sawaya, Alexandra Christine Helena Frankland; Paes Leme, Adriana Franco; Mazzafera, Paulo

2014-09-01

Recalcitrance of plant biomass is closely related to the presence of the phenolic heteropolymer lignin in secondary cell walls, which has a negative effect on forage digestibility, biomass-to-biofuels conversion and chemical pulping. The genus Eucalyptus is the main source of wood for pulp and paper industry. However, when compared to model plants such as Arabidopsis thaliana and poplar, relatively little is known about lignin biosynthesis in Eucalyptus and only a few genes were functionally characterized. An efficient, fast and inexpensive in vitro system was developed to study lignification in Eucalyptus globulus and to evaluate the potential role of candidate genes in this biological process. Seedlings were grown in four different conditions, in the presence or absence of light and with or without sucrose in the growth medium, and several aspects of lignin metabolism were evaluated. Our results showed that light and, to a lesser extent, sucrose induced lignin biosynthesis, which was followed by changes in S/G ratio, lignin oligomers accumulation and gene expression. In addition, higher total peroxidase activity and differential isoperoxidase profile were observed when seedlings were grown in the presence of light and sucrose. Peptide sequencing allowed the identification of differentially expressed peroxidases, which can be considered potential candidate class III peroxidases involved in lignin polymerization in E. globulus. © 2014 Scandinavian Plant Physiology Society.

Post-fire plant diversity and abundance in pine and eucalypt stands in Portugal : Effects of biogeography, topography, forest type and post-fire management

NARCIS (Netherlands)

Maia, P.; Keizer, J.; Vasques, A.; Abrantes, N.; Roxo, L.; Fernandes, P.; Ferreira, A.; Moreira, F.

2014-01-01

This study concerned the mid-term regeneration of the woody understory vegetation of pure and mixed stands of Pinus pinaster Ait. and Eucalyptus globulus Labill. in northern and central Portugal following wildfires in 2005 and 2006. Pine and eucalypt stands are the most widespread and most

Can Acceptable Pulp be Obtained from Eucalyptus globulus Wood Chips after Hemicellulose Extraction?

OpenAIRE

Francisco López; M. Trinidad García; Vicente Mena; J. Mauricio Loaiza; Minerva A. M. Zamudio; Juan C. García

2014-01-01

This study investigates the operating conditions used in the soda-anthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or be...

COMPORTAMENTO ESPECTRAL DE FOLHAS DE Eucalyptus globulus (Labill. ATACADAS POR Mycosphaerella spp. NAS REGIÕES DO VISÍVEL E DO INFRAVERMELHO PRÓXIMO DO ESPECTRO ELETROMAGNÉTICO

Directory of Open Access Journals (Sweden)

Diogo Belmonte Lippert

2015-01-01

Full Text Available The study aims to analyze the spectral behavior of leaves of Eucalyptus globulus attacked in four different severity levels by Mycosphaerella spp. in different positions in the canopy of the tree in the four seasons, considering two regions of the electromagnetic spectrum: visible and near infrared. The plant material was collected in all seasons, in different positions in the tree (base, middle and top of the canopy extract. In the laboratory, leaves were classified into four levels of severity (healthy, little, medium and heavy fire and then made measurements of spectral reflectance measured with a spectroradiometer. The spectral behavior of Eucalyptus globules leaves is characteristic according to the severity degree of the disease, differing primarily in the other high levels of infection by Mycosphaerella spp. and differ mainly of healthy leaves and leaves which are little attacked, in both regions of the electromagnetic spectrum, this behavior occurs for different treetop positions and climate seasons, varying the amount of reflected energy. It is concluded that the reflectance of the Eucalyptus globules leaves attacked by Mycosphaerella spp. differs according to the position in the tree crown and the weather station when they were collected and to the advanced levels of disease severity.

Water relations link carbon and oxygen isotope discrimination to phloem sap sugar concentration in eucalyptus globulus

International Nuclear Information System (INIS)

Cernusak, L.A.; Farquhar, G.D.; Arthur, D.J; Pate, J.S.

2002-01-01

Full text: The carbon isotope ratio of phloem sap sugars has been previously observed to correlate strongly with the phloem sap sugar concentration in Eucalyptus globulus. We hypothesized that the correspondence between these two parameters results from co-linearity in their responses to variation in plant water potential. Carbon isotope discrimination is expected to decrease with decreasing plant water potential due to the influence of stomatal conductance on the ratio of intercellular to ambient CO 2 , concentrations (c 1 /c a ). Conversely, we expected the phloem sap sugar concentration to increase with decreasing plant water potential, thereby maintaining positive turgor pressure within the sieve tubes. The study comprised 40 individual Eucalyptus globulus trees growing in three plantations situated on opposing ends of a rainfall gradient in southwestern Australia. A strong correlation was observed between the carbon isotope ratio in phloem sap sugars and phloem sap sugar concentration. Carbon isotope discrimination correlated positively with shoot water potential, whereas phloem sap sugar concentration correlated negatively with shoot water potential. The relationship between carbon isotope discrimination measured in phloem sap sugars collected from the stem and c 1 /c a measured instantaneously on subtending leaves was close to that theoretically predicted. Accordingly, a strong, negative relationship was observed between instantaneous c 1 /c a and the phloem sap sugar concentration. Oxygen isotope discrimination in phloem sap sugars also correlated strongly with phloem sap sugar concentration. A theoretical model suggested that the observed variation in stomatal conductance was sufficient to account for the variation observed in oxygen isotope discrimination across the study. Results strongly support the contention that water relations form a mechanistic link between phloem sap sugar concentration and both instantaneous and integrated measures of the

Emotional lability and affective synchrony in borderline personality disorder.

Science.gov (United States)

Schoenleber, Michelle; Berghoff, Christopher R; Tull, Matthew T; DiLillo, David; Messman-Moore, Terri; Gratz, Kim L

2016-07-01

Extant research on emotional lability in borderline personality disorder (BPD) has focused almost exclusively on lability of individual emotions or emotion types, with limited research considering how different types of emotions shift together over time. Thus, this study examined the temporal dynamics of emotion in BPD at the level of both individual emotions (i.e., self-conscious emotions [SCE], anger, and anxiety) and mixed emotions (i.e., synchrony between emotions). One hundred forty-four women from the community completed a diagnostic interview and laboratory study involving 5 emotion induction tasks (each of which was preceded and followed by a 5-min resting period or neutral task). State ratings of SCE, anger, and anxiety were provided at 14 time points (before and after each laboratory task and resting period). Hierarchical linear modeling results indicate that women with BPD reported greater mean levels of SCE and Anxiety (but not Anger), and greater lability of Anxiety. Women with BPD also exhibited greater variability in lability of all 3 emotions (suggestive of within-group differences in the relevance of lability to BPD). Results also revealed synchrony (i.e., positive relations) between each possible pair of emotions, regardless of BPD status. Follow-up regression analyses suggest the importance of accounting for lability when examining the role of synchrony in BPD, as the relation of SCE-Anger synchrony to BPD symptom severity was moderated by Anger and SCE lability. Specifically, synchronous changes in SCE and Anger were associated with greater BPD symptom severity when large shifts in SCE were paired with minor shifts in Anger. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Lability of nanoparticulate metal complexes in electrochemical speciation analysis

DEFF Research Database (Denmark)

van Leeuwen, Herman P.; Town, Raewyn M.

2016-01-01

Lability concepts are elaborated for metal complexes with soft (3D) and hard (2D) aqueous nanoparticles. In the presence of a non-equilibrium sensor, e.g. a voltammetric electrode, the notion of lability for nanoparticulate metal complexes, M-NP, reflects the ability of the M-NP to maintain...... equilibrium with the reduced concentration of the electroactive free M2+ in its diffusion layer. Since the metal ion binding sites are confined to the NP body, the conventional reaction layer in the form of a layer adjacent to the electrode surface is immaterial. Instead an intraparticulate reaction zone may...... of the electrochemical technique is crucial in the lability towards the electrode surface. In contrast, for nanoparticulate complexes it is the dynamics of the exchange of the electroactive metal ion with the surrounding medium that governs the effective lability towards the electrode surface....

Pharmacological ascorbate and ionizing radiation (IR increase labile iron in pancreatic cancer

Directory of Open Access Journals (Sweden)

Justin C. Moser

2014-01-01

Full Text Available Labile iron, i.e. iron that is weakly bound and is relatively unrestricted in its redox activity, has been implicated in both the pathogenesis as well as treatment of cancer. Two cancer treatments where labile iron may contribute to their mechanism of action are pharmacological ascorbate and ionizing radiation (IR. Pharmacological ascorbate has been shown to have tumor-specific toxic effects due to the formation of hydrogen peroxide. By catalyzing the oxidation of ascorbate, labile iron can enhance the rate of formation of hydrogen peroxide; labile iron can also react with hydrogen peroxide. Here we have investigated the magnitude of the labile iron pool in tumor and normal tissue. We also examined the ability of pharmacological ascorbate and IR to change the size of the labile iron pool. Although a significant amount of labile iron was seen in tumors (MIA PaCa-2 cells in athymic nude mice, higher levels were seen in murine tissues that were not susceptible to pharmacological ascorbate. Pharmacological ascorbate and irradiation were shown to increase the labile iron in tumor homogenates from this murine model of pancreatic cancer. As both IR and pharmacological ascorbate may rely on labile iron for their effects on tumor tissues, our data suggest that pharmacological ascorbate could be used as a radio-sensitizing agent for some radio-resistant tumors.

Organic matter production in an age series of Eucalyptus globulus plantations in Tamil Nadu

Energy Technology Data Exchange (ETDEWEB)

Negi, J D.S.; Bora, N K.S.; Tandon, V N; Thapliyal, H D

1984-08-01

The distribution of organic matter in an age series of Eucalyptus globulus plantations in Tamil Nadu is discussed. The total biomass ranges from 38 tonnes (5 years) to 220 tonnes (16 years) per ha with 85 to 88 percent being contributed by the aboveground parts and 15 to 12 percent by the roots and the average annual production of non-photosynthetic components is at its peak (19 tonnes/ha) at the age of 7 years. 17 references, 4 tables.

Transient acidosis while retrieving a fear-related memory enhances its lability

Science.gov (United States)

Du, Jianyang; Price, Margaret P; Taugher, Rebecca J; Grigsby, Daniel; Ash, Jamison J; Stark, Austin C; Hossain Saad, Md Zubayer; Singh, Kritika; Mandal, Juthika; Wemmie, John A; Welsh, Michael J

2017-01-01

Attenuating the strength of fearful memories could benefit people disabled by memories of past trauma. Pavlovian conditioning experiments indicate that a retrieval cue can return a conditioned aversive memory to a labile state. However, means to enhance retrieval and render a memory more labile are unknown. We hypothesized that augmenting synaptic signaling during retrieval would increase memory lability. To enhance synaptic transmission, mice inhaled CO2 to induce an acidosis and activate acid sensing ion channels. Transient acidification increased the retrieval-induced lability of an aversive memory. The labile memory could then be weakened by an extinction protocol or strengthened by reconditioning. Coupling CO2 inhalation to retrieval increased activation of amygdala neurons bearing the memory trace and increased the synaptic exchange from Ca2+-impermeable to Ca2+-permeable AMPA receptors. The results suggest that transient acidosis during retrieval renders the memory of an aversive event more labile and suggest a strategy to modify debilitating memories. DOI: http://dx.doi.org/10.7554/eLife.22564.001 PMID:28650315

Yield models for Eucalyptus globulus fuelwood plantations in Ethiopia

Energy Technology Data Exchange (ETDEWEB)

Pukkala, T.; Pohjonen, V. (Joensuu Univ. (FI). Faculty of Forestry)

1990-01-01

Based on 53 tree analyses and 105 sample plots of Eucalyptus globulus, models for volume and biomass at single tree and stand levels were developed. The possible growing sites were divided into four site classes. In seedling stands, the site class I corresponds to yield class 44 m{sup 3} ha{sup -1} year{sup -1}, in coppice stands to yield class 46 m{sup 3} ha{sup -1} year{sup -1}. The site class IV corresponds in seedling stand to yield class 9 m{sup 3} ha{sup -1} year{sup -1}, in coppice stands to yield class 13 m{sup 3} ha{sup -1} year{sup -1}. The maximum mean annual increment was reached in seedling stands at the age of 18-19 years, in coppice stands at the age of 14 years. (author).

VARIABILIDAD Y RELACION ENTRE LAS PROPIEDADES ANATOMICAS, QUIMICAS Y LA APTITUD PULPABLE, EN CLONES DE EUCALYPTUS GLOBULUS.

OpenAIRE

RAMIREZ VIDAL, MAURICIO HERNAN; RAMIREZ VIDAL, MAURICIO HERNAN

2008-01-01

Se estudió la variación de la anatomía de la madera, variables biornétricas, aptitud pulpable y propiedades de la pulpa, en 14 clones de E. globulus de 7 años de edad, creciendo en un ensayo clonal en la zona de Arauco, región del Bio-Bio, Chile. Las Cara 61p.

Eucalyptus globulus extract protects upon acetaminophen-induced kidney damages in male rat

Science.gov (United States)

Dhibi, Sabah; Mbarki, Sakhria; Elfeki, Abdelfettah; Hfaiedh, Najla

2014-01-01

Plants have historically been used in treating many diseases. Eucalyptus globules, a rich source of bioactive compounds, and have been shown to possess antioxidative properties. The purpose of this study, carried out on male Wistar rats, was to evaluate the beneficial effects of Eucalyptus globulus extract upon acetaminophen-induced damages in kidney. Our study is realized in the Department of Biology, Faculty of Sciences of Sfax (Tunisia). 32 Wistar male rats; were divided into 4 batches: a control group (n=8), a group of rats treated with acetaminophen (goomg/kg) by intraperitoneal injection during 4 days (n=8), a group receiving Eucalyptus globulus extract (130 mg of dry leaves/kg/day) in drinking water during 42 days after 2 hours of acetaminophen administration (during 4 days) (n=8) and group received only Eucalyptus (n=8) during 42 days. After 6 weeks, animals from each group were rapidly sacrificed by decapitation. Blood serum was obtained by centrifugation. Under our experimental conditions, acetaminophen poisoning resulted in an oxidative stress evidenced by statistically significant losses in the activities of catalase (CAT), superoxide-dismutase (SOD), glutathione-peroxidase (GPX) activities and an increase in lipids peroxidation level in renal tissue of acetaminophen-treated group compared with the control group. Acetaminophen also caused kidney damage as evident by statistically significant (p<0.05) increase in levels of creatinine and urea and decreased levels of uric acid and proteins in blood. Histological analysis demonstrated alteration of proximal tubules, atrophy of the glomerule and dilatation of urinary space. Previous administration of plant extract is found to alleviate this acetaminophen-induced damage. PMID:24856382

ESTUDIOS SOBRE EL COMPORTAMIENTO DE FORRAJEO DE Acromyrmex lundi Guering (HYMENOPTERA, FORMICIDAE Y SU EFECTO SOBRE EL CRECIMIENTO DE PROCEDENCIAS DE Eucalyptus globulus Labill. (Myrtaceae

Directory of Open Access Journals (Sweden)

Carmen Lidia Martínez

2015-02-01

Full Text Available El ataque de las hormigas cortadoras es una de las principales razones de pérdida de plantas durante la etapa de establecimiento de un monte forestal. Los objetivos de este estudio fueron evaluar la intensidad de forrajeo de Acromyrmex lundi asociado a algunas condiciones ambientales y procedencias de Eucalyptus globulus y estimar el impacto de la herbivoría sobre el crecimiento inicial de estos árboles. Dos ensayos se llevaron a cabo durante dos temporadas estivo-otoñales consecutivas, en el Campo Experimental de la Universidad Nacional de Luján, Argentina. Los materiales de diferentes procedencias fueron dispuestos en bloques equidistantes a 5 m de un nido activo de A. lundi. Durante doce semanas se contabilizó el número de hojas cortadas por las hormigas y se registraron algunas variables meteorológicas. En el segundo año la mitad de las parcelas fue protegida de las hormigas y se midieron variables de crecimiento. Los materiales de todas las procedencias fueron atacadas por A. lundi, aunque el número de hojas cosechada fue significativamente diferente sólo entre los orígenes Flinders Island (52,5 hojas y Nullo Mountain (28,5 hojas. El número de días lluviosos fue el único factor ambiental que se relacionó positivamente con la actividad de las hormigas.Todos los tratamientos redujeron significativamente la altura, el diámetro y el área foliar cuando fueron atacados por las hormigas. Las distintas procedencias compensaron diferencialemnte la herbivoría. Se discuten los resultados en función de los criterios a tener en cuenta para la selección de materiales genéticos como herramienta de manejo y control del ataque de A. lundi.

Repeated labilization-reconsolidation processes strengthen declarative memory in humans.

Directory of Open Access Journals (Sweden)

Cecilia Forcato

Full Text Available The idea that memories are immutable after consolidation has been challenged. Several reports have shown that after the presentation of a specific reminder, reactivated old memories become labile and again susceptible to amnesic agents. Such vulnerability diminishes with the progress of time and implies a re-stabilization phase, usually referred to as reconsolidation. To date, the main findings describe the mechanisms associated with the labilization-reconsolidation process, but little is known about its functionality from a biological standpoint. Indeed, two functions have been proposed. One suggests that destabilization of the original memory after the reminder allows the integration of new information into the background of the original memory (memory updating, and the other suggests that the labilization-reconsolidation process strengthens the original memory (memory strengthening. We have previously reported the reconsolidation of human declarative memories, demonstrating memory updating in the framework of reconsolidation. Here we deal with the strengthening function attributed to the reconsolidation process. We triggered labilization-reconsolidation processes successively by repeated presentations of the proper reminder. Participants learned an association between five cue-syllables and their respective response-syllables. Twenty-four hours later, the paired-associate verbal memory was labilized by exposing the subjects to one, two or four reminders. The List-memory was evaluated on Day 3 showing that the memory was improved when at least a second reminder was presented in the time window of the first labilization-reconsolidation process prompted by the earlier reminder. However, the improvement effect was revealed on Day 3, only when at least two reminders were presented on Day 2 and not as a consequence of only retrieval. Therefore, we propose central concepts for the reconsolidation process, emphasizing its biological role and the

Repeated Labilization-Reconsolidation Processes Strengthen Declarative Memory in Humans

Science.gov (United States)

Forcato, Cecilia; Rodríguez, María L. C.; Pedreira, María E.

2011-01-01

The idea that memories are immutable after consolidation has been challenged. Several reports have shown that after the presentation of a specific reminder, reactivated old memories become labile and again susceptible to amnesic agents. Such vulnerability diminishes with the progress of time and implies a re-stabilization phase, usually referred to as reconsolidation. To date, the main findings describe the mechanisms associated with the labilization-reconsolidation process, but little is known about its functionality from a biological standpoint. Indeed, two functions have been proposed. One suggests that destabilization of the original memory after the reminder allows the integration of new information into the background of the original memory (memory updating), and the other suggests that the labilization-reconsolidation process strengthens the original memory (memory strengthening). We have previously reported the reconsolidation of human declarative memories, demonstrating memory updating in the framework of reconsolidation. Here we deal with the strengthening function attributed to the reconsolidation process. We triggered labilization-reconsolidation processes successively by repeated presentations of the proper reminder. Participants learned an association between five cue-syllables and their respective response-syllables. Twenty-four hours later, the paired-associate verbal memory was labilized by exposing the subjects to one, two or four reminders. The List-memory was evaluated on Day 3 showing that the memory was improved when at least a second reminder was presented in the time window of the first labilization-reconsolidation process prompted by the earlier reminder. However, the improvement effect was revealed on Day 3, only when at least two reminders were presented on Day2 and not as a consequence of only retrieval. Therefore, we propose central concepts for the reconsolidation process, emphasizing its biological role and the parametrical constrains

Construction of hierarchically porous metal-organic frameworks through linker labilization

Science.gov (United States)

Yuan, Shuai; Zou, Lanfang; Qin, Jun-Sheng; Li, Jialuo; Huang, Lan; Feng, Liang; Wang, Xuan; Bosch, Mathieu; Alsalme, Ali; Cagin, Tahir; Zhou, Hong-Cai

2017-05-01

A major goal of metal-organic framework (MOF) research is the expansion of pore size and volume. Although many approaches have been attempted to increase the pore size of MOF materials, it is still a challenge to construct MOFs with precisely customized pore apertures for specific applications. Herein, we present a new method, namely linker labilization, to increase the MOF porosity and pore size, giving rise to hierarchical-pore architectures. Microporous MOFs with robust metal nodes and pro-labile linkers were initially synthesized. The mesopores were subsequently created as crystal defects through the splitting of a pro-labile-linker and the removal of the linker fragments by acid treatment. We demonstrate that linker labilization method can create controllable hierarchical porous structures in stable MOFs, which facilitates the diffusion and adsorption process of guest molecules to improve the performances of MOFs in adsorption and catalysis.

Functional relationships between wood structure and vulnerability to xylem cavitation in races of Eucalyptus globulus differing in wood density.

Science.gov (United States)

Barotto, Antonio José; Monteoliva, Silvia; Gyenge, Javier; Martinez-Meier, Alejandro; Fernandez, María Elena

2018-02-01

Wood density can be considered as a measure of the internal wood structure, and it is usually used as a proxy measure of other mechanical and functional traits. Eucalyptus is one of the most important commercial forestry genera worldwide, but the relationship between wood density and vulnerability to cavitation in this genus has been little studied. The analysis is hampered by, among other things, its anatomical complexity, so it becomes necessary to address more complex techniques and analyses to elucidate the way in which the different anatomical elements are functionally integrated. In this study, vulnerability to cavitation in two races of Eucalyptus globulus Labill. with different wood density was evaluated through Path analysis, a multivariate method that allows evaluation of descriptive models of causal relationship between variables. A model relating anatomical variables with wood properties and functional parameters was proposed and tested. We found significant differences in wood basic density and vulnerability to cavitation between races. The main exogenous variables predicting vulnerability to cavitation were vessel hydraulic diameter and fibre wall fraction. Fibre wall fraction showed a direct impact on wood basic density and the slope of vulnerability curve, and an indirect and negative effect over the pressure imposing 50% of conductivity loss (P50) through them. Hydraulic diameter showed a direct negative effect on P50, but an indirect and positive influence over this variable through wood density on one hand, and through maximum hydraulic conductivity (ks max) and slope on the other. Our results highlight the complexity of the relationship between xylem efficiency and safety in species with solitary vessels such as Eucalyptus spp., with no evident compromise at the intraspecific level. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Freshwater processing of terrestrial dissolved organic matter: What governs lability?

Science.gov (United States)

D'Andrilli, J.; Smith, H. J.; Junker, J. R.; Scholl, E. A.; Foreman, C. M.

2016-12-01

Aquatic and terrestrial ecosystems are linked through the transfer of energy and materials. Allochthonous organic matter (OM) is central to freshwater ecosystem function, influencing local food webs, trophic state, and nutrient availability. In order to understand the nature and fate of OM from inland headwaters to the open ocean, it is imperative to understand the links between OM lability and ecosystem function. Thus, biological, chemical, and physical factors need to be evaluated together to inform our understanding of environmental lability. We performed a laboratory processing experiment on naturally occurring OM leachates from riparian leaves, grasses, and pine needles. Measures of water chemistry, OM optical and molecular characterization, bacterial abundances, microbial assemblage composition, respiration, and C:N:P were integrated to discern the nature and fate of labile and recalcitrant OM in a freshwater stream. Peak processing of all OM sources in the stream water occurred after two days, with spikes in bacterial cell abundances, respiration rates, microbial assemblage shifts, and maximum C utilization. Respiration rates and microbial assemblages were dependent on the degree of lability of the OM molecular composition. Within the first few days, no differences in respiration rates were observed between leachate sources, however, beyond day five, the rates diverged with C processing efficiency correlated with OM lability. Originally comprised of amino acid-like, labile fluorescent species, the inoculated stream water OM became more recalcitrant after 16 days, indicating humification processing over time. Our study highlights the importance of interdisciplinary approaches for understanding the processing and fate of OM in aquatic ecosystems.

Uso de antraquinona en cocción kraft de Eucalyptus globulus y Eucalyptus nitens

OpenAIRE

Moreira, Jorge Felipe Quintana

2011-01-01

En la presente disertación se verificó de manera experimental el efecto de la adición de Antraquinona al proceso de cocción batch convencional para una mezcla industrial de Eucalyptus globulus E. nitens.; en lo que respecta a su capacidad de aumentar la velocidad de la reacción de deslignificación y proporcionar estabilidad a las hemicelulosas y celulosas de la fibra. Lo anterior se logró con experiencias de laboratorio fijando las condiciones de cocción de acuerdo a la operación de los dig...

Fate and lability of silver in soils: Effect of ageing

Science.gov (United States)

The fate and lability of added soluble Ag in soils over time was examined by measurement of labile metal (E-value) by isotopic dilution using the 110mAg radioactive isotope and the solid-phase speciation of Ag by X-ray absorption near edge structure (XANES) spectrosco...

Transfer Rates of 238U and 232Th for E. globulus, A. mearnsii, H. filipendula and Hazardous Effects of the Usage of Medicinal Plants From Around Gold Mine Dump Environs

Directory of Open Access Journals (Sweden)

Victor M. Tshivhase

2015-12-01

Full Text Available Medicinal plant consumption can be a source of human exposure to radioactive elements such as 238U and 232Th, which can lead to internal radiation doses. The uptake of 238U and 232Th from soils to the leaf samples of three different medicinal plant species (Eucalyptus globulus, Acacia mearnsii and Hyparrhenia filipendula from the purlieu of the Princess gold mine dump, an abandoned contaminated tailings storage site (TSS, located at longitude 27°55′00″E and latitude 26°09′30″S in Davidsonville (Roodepoort, west of Johannesburg, South Africa was measured. This was done using ICP-MS spectrometry and substantial differences were observed in the soil-plant transfer factor (TF values between these radionuclides. The plant species E. globulus exhibited the highest uptake of 238U, with an average TF of 3.97, while that of H. filipendula was 0.01 and the lowest TF of 0.15 × 10−2 was measured for A. mearnsii. However, in the case of 232Th, the highest average TF was observed for A. mearnsii (0.29, followed by E. globulus (0.10 and lowest was measured for H. filipendula (0.27 × 10−2. The ratio of TF average value i.e., 238U to 232Th in the soil-plant leaves was 38.05 for E. globulus, 0.01 for A. mearnsii and 4.38 for H. filipendula.

Transfer Rates of 238U and 232Th for E. globulus, A. mearnsii, H. filipendula and Hazardous Effects of the Usage of Medicinal Plants From Around Gold Mine Dump Environs

Science.gov (United States)

Tshivhase, Victor M.; Njinga, Raymond L.; Mathuthu, Manny; Dlamini, Thulani C.

2015-01-01

Medicinal plant consumption can be a source of human exposure to radioactive elements such as 238U and 232Th, which can lead to internal radiation doses. The uptake of 238U and 232Th from soils to the leaf samples of three different medicinal plant species (Eucalyptus globulus, Acacia mearnsii and Hyparrhenia filipendula) from the purlieu of the Princess gold mine dump, an abandoned contaminated tailings storage site (TSS), located at longitude 27°55′00″E and latitude 26°09′30″S in Davidsonville (Roodepoort, west of Johannesburg, South Africa) was measured. This was done using ICP-MS spectrometry and substantial differences were observed in the soil-plant transfer factor (TF) values between these radionuclides. The plant species E. globulus exhibited the highest uptake of 238U, with an average TF of 3.97, while that of H. filipendula was 0.01 and the lowest TF of 0.15 × 10−2 was measured for A. mearnsii. However, in the case of 232Th, the highest average TF was observed for A. mearnsii (0.29), followed by E. globulus (0.10) and lowest was measured for H. filipendula (0.27 × 10−2). The ratio of TF average value i.e., 238U to 232Th in the soil-plant leaves was 38.05 for E. globulus, 0.01 for A. mearnsii and 4.38 for H. filipendula. PMID:26690462

Assessing soil carbon lability by near infrared spectroscopy and NaOCL oxidation

DEFF Research Database (Denmark)

Thomsen, Ingrid Kaag; Bruun, Sander; Jensen, Lars Stoumann

2009-01-01

The feasibility of near infrared (NIR) spectroscopy for quantifying labile organic matter (OM) in arable soils and for predicting soil refractory OM fractions was tested on 37 soils varying in texture and soil carbon (C) content. Three sets of arable soils (0-20 cm depth) were sampled from 1) long......-term field experiments with different OM inputs, 2) individual sites with inherent with-in field gradients in soil texture and/or C content, and 3) from a range of different sites covering variations in management and geological origin. The labile OM fraction was defined by the CO2 evolved from the soils...... incubated for 34 weeks while refractory OM was obtained by NaOCl oxidation. The labile fraction of the soil C accounted for 2-12% of the total soil C content. No systematic relationship between labile C content and total soil C or clay was found, but NIR spectra could be correlated well with the labile C...

Efeito do óleo essencial de Eucalyptus globulus sobre espécies produtoras de aflatoxinas

OpenAIRE

Georgia Rocha Vilela

2007-01-01

Há relatos na literatura de alguns compostos naturais de plantas que são usados para preservação de alimentos e no controle do desenvolvimento de fungos e bactérias que ocorrem em plantas, grãos, cereais e derivados. O presente trabalho teve como objetivo avaliar "in vitro" o efeito do óleo essencial de Eucalyptus globulus e seu composto majoritário sobre o crescimento micelial dos fungos Aspergillus flavus e Aspergillus parasiticus e a produção de aflatoxinas. A composição química do...

DNA lability induced by nimustine and ramustine in rat glioma cells.

Science.gov (United States)

Mineura, K; Fushimi, S; Itoh, Y; Kowada, M

1988-01-01

The DNA labile sites induced by two nitrosoureas, nimustine (ACNU) and ramustine (MCNU) synthesised in Japan, have been examined in highly reiterated DNA sequences of rat glioma cells. Reiterated fragments of 167 and 203 base pairs (bp), obtained after Hind III and Hae III restriction endonuclease digestion of rat glioma cells DNA, were used as target DNA sequences to determine the labile sites. In vitro reaction with ACNU and MCNU resulted in scission products corresponding to the locations of guanine. Subsequent piperidine hydrolysis produced more frequent breaks of the phosphodiester bonds at guanine positions, thus forming alkali-labile sites. Images PMID:3236017

The effect of vapour pressure deficit on stomatal conductance, sap pH and leaf-specific hydraulic conductance in Eucalyptus globulus clones grown under two watering regimes.

Science.gov (United States)

Hernandez, Maria Jose; Montes, Fernando; Ruiz, Federico; Lopez, Gustavo; Pita, Pilar

2016-05-01

Stomatal conductance has long been considered of key interest in the study of plant adaptation to water stress. The expected increase in extreme meteorological events under a climate change scenario may compromise survival in Eucalyptus globulus plantations established in south-western Spain. We investigated to what extent changes in stomatal conductance in response to high vapour pressure deficits and water shortage are mediated by hydraulic and chemical signals in greenhouse-grown E. globulus clones. Rooted cuttings were grown in pots and submitted to two watering regimes. Stomatal conductance, shoot water potential, sap pH and hydraulic conductance were measured consecutively in each plant over 4 weeks under vapour pressure deficits ranging 0·42 to 2·25 kPa. Evapotranspiration, growth in leaf area and shoot biomass were also determined. There was a significant effect of both clone and watering regime in stomatal conductance and leaf-specific hydraulic conductance, but not in sap pH. Sap pH decreased as water potential and stomatal conductance decreased under increasing vapour pressure deficit. There was no significant relationship between stomatal conductance and leaf-specific hydraulic conductance. Stomata closure precluded shoot water potential from falling below -1·8 MPa. The percentage loss of hydraulic conductance ranged from 40 to 85 %. The highest and lowest leaf-specific hydraulic conductances were measured in clones from the same half-sib families. Water shortage reduced growth and evapotranspiration, decreases in evapotranspiration ranging from 14 to 32 % in the five clones tested. Changes in sap pH seemed to be a response to changes in atmospheric conditions rather than soil water in the species. Stomata closed after a considerable amount of hydraulic conductance was lost, although intraspecific differences in leaf-specific hydraulic conductance suggest the possibility of selection for improved productivity under water-limiting conditions

Non-labile Soil Nitrogen Retention beneath Three Tree Species in a Tropical Plantation

Science.gov (United States)

Jason P. Kaye; Dan Binkley; Xiaoming Zou

2002-01-01

Soil organic matter is the largest sink for N additions to forests. Species composition may affect soilNretention by altering the amount or proportion of added N stored in non-labile organic pools. We measured 15N tracer retention in labile and non-labile pools of surface (0–20 cm) mineral soils, 7 yr after the tracer was applied to a 9 yr-old Puerto Rican tree...

Maternal emotion socialization differentially predicts third-grade children's emotion regulation and lability.

Science.gov (United States)

Rogers, Megan L; Halberstadt, Amy G; Castro, Vanessa L; MacCormack, Jennifer K; Garrett-Peters, Patricia

2016-03-01

Numerous parental emotion socialization factors have been implicated as direct and indirect contributors to the development of children's emotional competence. To date, however, no study has combined parents' emotion-related beliefs, behaviors, and regulation strategies in one model to assess their cumulative-as well as unique-contributions to children's emotion regulation. We considered the 2 components that have recently been distinguished: emotion regulation and emotional lability. We predicted that mothers' beliefs about the value of and contempt for children's emotions, mothers' supportive and nonsupportive reactions to their children's emotions, as well as mothers' use of cognitive reappraisal and suppression of their own emotions would each contribute unique variance to their children's emotion regulation and lability, as assessed by children's teachers. The study sample consisted of an ethnically and socioeconomically diverse group of 165 mothers and their third-grade children. Different patterns emerged for regulation and lability: Controlling for family income, child gender, and ethnicity, only mothers' lack of suppression as a regulatory strategy predicted greater emotion regulation in children, whereas mothers' valuing of children's emotions, mothers' lack of contempt for children's emotions, mothers' use of cognitive reappraisal to reinterpret events, and mothers' lack of emotional suppression predicted less lability in children. These findings support the divergence of emotion regulation and lability as constructs and indicate that, during middle childhood, children's lability may be substantially and uniquely affected by multiple forms of parental socialization. (c) 2016 APA, all rights reserved).

Knowledge Lability: Within-Person Changes in Parental Knowledge and Their Associations with Adolescent Problem Behavior.

Science.gov (United States)

Lippold, Melissa A; Fosco, Gregory M; Ram, Nilam; Feinberg, Mark E

2016-02-01

Higher levels of parental knowledge about youth activities have been associated with lower levels of youth risky behavior. Yet little is known about how parental knowledge fluctuates during early adolescence and how those fluctuations are associated with the development of problem behavior. We use the term lability to describe within-person fluctuations in knowledge over time with higher lability indicating greater fluctuations in knowledge from year-to-year. This longitudinal study of rural adolescents (N = 840) investigated if change in parental knowledge across four waves of data from grades 6 to 8 is characterized by lability, and if greater lability is associated with higher youth substance use, delinquency, and internalizing problems in grade 9. Our models indicated that only some of the variance in parental knowledge was accounted for by developmental trends. The remaining residual variance reflects within-person fluctuations around these trends, lability, and measurement and occasion-specific error. Even controlling for level and developmental trends in knowledge, higher knowledge lability (i.e., more fluctuation) was associated with increased risk for later alcohol and tobacco use, and for girls, higher delinquency and internalizing problems. Our findings suggest that lability in parental knowledge has unique implications for adolescent outcomes. The discussion focuses on mechanisms that may link knowledge lability to substance use. Interventions may be most effective if they teach parents to consistently and predictably decrease knowledge across early adolescence.

LABILE IRON IN CELLS AND BODY FLUIDS . Physiology, Pathology and Pharmacology

Directory of Open Access Journals (Sweden)

Zvi Ioav Cabantchik

2014-03-01

Full Text Available In living systems iron appears predominantly associated with proteins, but can also be detected in forms referred as labile iron, which denotes the combined redox properties of iron and its amenability to exchange between ligands, including chelators. The labile cell iron (LCI composition varies with metal concentration and substances with chelating groups but also with pH and the redox potential. Although physiologically in the lower µM range, LCI plays a key role in cell iron economy as cross-roads of metabolic pathways. LCI levels are continually regulated by an iron-responsive machinery that balances iron uptake versus deposition into ferritin. However, LCI rises aberrantly in some cell types due to faulty cell utilization pathways or infiltration by pathological iron forms that are found in hemosiderotic plasma. As LCI attains pathological levels, it can catalyze reactive O species (ROS formation that, at particular threshold, can surpass cellular anti-oxidant capacities and seriously damage its constituents. While in normal plasma and interstitial fluids, virtually all iron is securely carried by circulating transferrin (that renders iron essentially non-labile, in systemic iron overload (IO, the total plasma iron binding capacity is often surpassed by a massive iron influx from hyperabsorptive gut or from erythrocyte overburdened spleen and/or liver. As plasma transferrin approaches iron saturation, labile plasma iron (LPI emerges in forms that can infiltrate cells by unregulated routes and raise LCI to toxic levels. Despite the limited knowledge available on LPI speciation in different types and degrees of iron overload, LPI measurements can be and are in fact used for identifying systemic IO and for initiating/adjusting chelation regimens to attain full-day LPI protection. A recent application of labile iron assay is the detection of labile components in iv iron formulations per se as well as in plasma (LPI following parenteral iron

Quantification of Labile Soil Mercury by Stable Isotope Dilution Techniques

Science.gov (United States)

Shetaya, Waleed; Huang, Jen-How; Osterwalder, Stefan; Alewell, Christine

2016-04-01

Mercury (Hg) is a toxic element that can cause severe health problems to humans. Mercury is emitted to the atmosphere from both natural and anthropogenic sources and can be transported over long distances before it is deposited to aquatic and terrestrial environments. Aside from accumulation in soil solid phases, Hg deposited in soils may migrate to surface- and ground-water or enter the food chain, depending on its lability. There are many operationally-defined extraction methods proposed to quantify soil labile metals. However, these methods are by definition prone to inaccuracies such as non-selectivity, underestimation or overestimation of the labile metal pool. The isotopic dilution technique (ID) is currently the most promising method for discrimination between labile and non-labile metal fractions in soil with a minimum disturbance to soil-solid phases. ID assesses the reactive metal pool in soil by defining the fraction of metal both in solid and solution phases that is isotopically-exchangeable known as the 'E-value'. The 'E-value' represents the metal fraction in a dynamic equilibrium with the solution phase and is potentially accessible to plants. This is carried out by addition of an enriched metal isotope to soil suspensions and quantifying the fraction of metal that is able to freely exchange with the added isotope by measuring the equilibrium isotopic ratio by ICP-MS. E-value (mg kg-1) is then calculated as follows: E-Value = (Msoil/ W) (CspikeVspike/ Mspike) (Iso1IAspike -Iso2IAspikeRss / Iso2IAsoil Rss - Iso1IAsoil) where M is the average atomic mass of the metal in the soil or the spike, W is the mass of soil (kg), Cspike is the concentration of the metal in the spike (mg L-1), Vspike is the volume of spike (L), IA is isotopic abundance, and Rss is the equilibrium ratio of isotopic abundances (Iso1:Iso2). Isotopic dilution has been successfully applied to determine E-values for several elements. However, to our knowledge, this method has not yet

Effects of essential oils from Eucalyptus globulus leaves on soil organisms involved in leaf degradation.

Directory of Open Access Journals (Sweden)

Carla Martins

Full Text Available The replacement of native Portuguese forests by Eucalyptus globulus is often associated with deleterious effects on terrestrial and aquatic communities. Several studies have suggested that such a phenomenon is linked with the leaf essential oils released into the environment during the Eucalyptus leaf degradation process. However, to date, the way these compounds affect leaf degradation in terrestrial systems i.e. by direct toxic effects to soil invertebrates or indirectly by affecting food of soil fauna, is still unknown. In order to explore this question, the effect of essential oils extracted from E. globulus leaves on terrestrial systems was investigated. Fungal growth tests with species known as leaf colonizers (Mucor hiemalis, Alternaria alternata, Penicillium sp., Penicillium glabrum and Fusarium roseum were performed to evaluate the antifungal effect of essential oils. In addition, a reproduction test with the collembolans Folsomia candida was done using a gradient of eucalyptus essential oils in artificial soil. The influence of essential oils on feeding behaviour of F. candida and the isopods Porcellio dilatatus was also investigated through food avoidance and consumption tests. Eucalyptus essential oils were lethal at concentrations between 2.5-20 µL/mL and inhibited growth of all fungal species between 1.25-5 µL/mL. The collembolan reproduction EC50 value was 35.0 (28.6-41.2 mg/kg and both collembola and isopods preferred leaves without oils. Results suggested that the effect of essential oils in leaf processing is related to direct toxic effects on fungi and soil fauna and to indirect effects on the quality and availability of food to soil invertebrates.

Resistance to high level of Cu (Copper) by arbuscular mycorrhizal, saprobe Fungi and Eucalyptus globules

International Nuclear Information System (INIS)

Arriagada, C.; Pereira, G.; Machuca, A.; Alvear, M.; Martin, J.; Ocampo, J.

2009-01-01

The effects of saprobe and arbuscular mycorrhizal (AM) fungi on growth, chorophyll, root length colonization and succinate dehydrogenase (SDH) activity was measured in Eucalyptus globulus Labill., plants growing in soil with high level of Cu were investigated. The application of Cu inhibited the development of mycelia of the saprobe fungi Fusarium concolor and Trichoderma koningii and the hyphal length of the arbuscular mycorrhizal fungi (AM) Glomus mosseae and G. deserticola in vitro. (Author)

Resistance to high level of Cu (Copper) by arbuscular mycorrhizal, saprobe Fungi and Eucalyptus globules

Energy Technology Data Exchange (ETDEWEB)

Arriagada, C.; Pereira, G.; Machuca, A.; Alvear, M.; Martin, J.; Ocampo, J.

2009-07-01

The effects of saprobe and arbuscular mycorrhizal (AM) fungi on growth, chorophyll, root length colonization and succinate dehydrogenase (SDH) activity was measured in Eucalyptus globulus Labill., plants growing in soil with high level of Cu were investigated. The application of Cu inhibited the development of mycelia of the saprobe fungi Fusarium concolor and Trichoderma koningii and the hyphal length of the arbuscular mycorrhizal fungi (AM) Glomus mosseaae and G. deserticola in vitro. (Author)

CARACTERIZACION DE GENES DESHIDRINA EN EUCALYPTUS GLOBULUS CUYA EXPRESION ES INDUCIDA POR LA ACLIMATACION A BAJA TEMPERATURA

OpenAIRE

FERNANDEZ REYES, MARTA ALEJANDRA

2011-01-01

Eucalyptus globulus es una especie importante para la producción de pulpa de madera en Chile, sin embargo presenta una gran sensibilidad a temperaturas de congelamiento. Durante los últimos años, muchos estudios han enfocado sus esfuerzos en dilucidar los mecanismos que regulan la respuesta de las plantas a baja temperatura, mediante el análisis de la expresión génica. En el presente trabajo se estudia la expresión de genes deshidrina durante el proceso de aclimatación a baja temperatura y...

CARACTERIZACION DE GENES DESHIDRINA EN EUCALYPTUS GLOBULUS CUYA EXPRESION ES INDUCIDA POR LA ACLIMATACION A BAJA TEMPERATURA

OpenAIRE

FERNANDEZ REYES ; MARTA ALEJANDRA; FERNANDEZ REYES ; MARTA ALEJANDRA

2011-01-01

Eucalyptus globulus es una especie importante para la producción de pulpa de madera en Chile, sin embargo presenta una gran sensibilidad a temperaturas de congelamiento. Durante los últimos años, muchos estudios han enfocado sus esfuerzos en dilucidar los mecanismos que regulan la respuesta de las plantas a baja temperatura, mediante el análisis de la expresión génica. En el presente trabajo se estudia la expresión de genes deshidrina durante el proceso de aclimatación a baja temperatura y la...

Antioxidant and Antiacetylcholinesterase Activities of Some Commercial Essential Oils and Their Major Compounds

Directory of Open Access Journals (Sweden)

Smail Aazza

2011-09-01

Full Text Available The commercial essential oils of Citrus aurantium L., Cupressus sempervirens L., Eucalyptus globulus Labill., Foeniculum vulgare Mill. and Thymus vulgaris L., isolated by steam distillation by a company of Morocco were evaluated in terms of in vitro antioxidant activity through several methods. In vitro acetylcholinesterase inhibitory activity was also determined. Citrus limon (L. Burm. f. oil was also studied, but it was obtained by peel expression. The best antioxidant was T. vulgaris oil, independent of the method used, mainly due to the presence of the phenolic monoterpenes thymol and carvacrol, which when studied as single compounds also presented the best activities. Concerning the acetylcholinesterase inhibition activity, E. globulus was the most effective. Nevertheless its main components 1,8-cineole and limonene were not the most active, a feature that corresponded to d-3-carene.

Characterization and Identification of the Basidiomycetous Fungus Associated with 'hoya de malvón' Grapevine Disease in Argentina

Directory of Open Access Journals (Sweden)

S. Lupo

2006-04-01

Full Text Available Inocutis jamaicensis (Murrill Gottlieb, J.E. Wright & Moncalvo was identified as the basidiomycetous species associated with ‘hoja de malvón’ grapevine disease in Argentina. Macro and micro-morphological characteristics of fruit bodies corresponded to those described for the white-rotting fungus associated with native plant species and Eucalyptus globulus Labill. planted in Uruguay. Monokariotic isolates were obtained from basidiospores produced by fruit bodies of I. jamaicensis collected from Vitis vinifera L. and E. globulus. Dikaryons and fruit bodies produced by pairing monokaryotic mycelium suggest that all these isolates belong to the same species. The analysis of RFLP of the dikaryon produced by pairing monokaryons derived from V. vinifera and E. globulus revealed fragments that corresponded to each monokaryon, confirming that isolates from Vitis mated with those from Eucalyptus. In order to compare grapevine and Uruguayan isolates, RFLPs from ITS region generated by restriction digestion with Alu I, Hae III, Hha I, Msp I and Taq I were performed. Differences found in some restriction pattern could reflect a certain degree of variability between dikariotic isolates, probably related with a particular lifestyle, host specificity or geographic origin.

EFFECT OF LIGNIN CONTENT OF Eucalyptus globulus WOOD IN KRAFT PULPING PERFORMANCE

Directory of Open Access Journals (Sweden)

Gabriel Valim Cardoso

2011-03-01

Full Text Available In this research, it was analyzed the lignin content effect of Eucalyptus globulus wood in kraft pulping optimization. Seventy-two laboratory cooking were made with wood chips obtained from six Eucalyptus globulus trees selected from a group of 50 trees. The wood chips from three trees with the lowest lignin content, with average 20,53%, were mixed proportionally based on the tree weights, obtaining the sample of low lignin content wood. The same was made to obtain the sample for wood chips with the highest lignin content, with average 23,02%. The two lignin levels were statistically different. The two wood samples had basic densities statistically not different. Using three maximum temperatures levels (160, 165 and 170ºC, and three active alkali charged (17, 18,5 and 20%, the wood chips were converted to kraft pulps. The pulps were then characterized to analyze the influence of the distinct treatments employed in the cooking on their properties. The effect of the cooking conditions was expressed by mathematical models in order to determine the optimum points for each of the evaluated properties. The optimization process indicated maximum temperature of 168ºC, and active alkali of 19%, for maximum kraft pulping yield to achieve kappa number 18; this result was for woods with low lignin content. For woods containing the high lignin content, the optimization showed maximum cooking temperature of 169ºC and active alkali of 19% for kappa number of 18. The average reduction of 2,49% in wood lignin content resulted a correspondent gain of 2,2% in the kraft yield (o.d. basis and a reduction on the active alkali charge of 1,2% (o.d. basis to achieve kappa numbers from 16 to 19, preserving pulp properties. If the option is to work with kappa number 19 instead of 16, the gain in kraft yield is approximately 2%. Therefore, when working with low lignin content wood and kappa number 19 instead of 16, a substantial gain of approximately 4,2% is obtained

Effect of exogenous phosphate on the lability and phytoavailability of arsenic in soils.

Science.gov (United States)

Wang, Jinjin; Zeng, Xibai; Zhang, Hao; Li, Yongtao; Zhao, Shizhen; Su, Shiming; Bai, Lingyu; Wang, Yanan; Zhang, Tuo

2018-04-01

The effect of exogenous phosphate (P, 200 mg⋅kg -1 soil) on the lability and phytoavailability of arsenic (As) was studied using the diffusive gradients in thin films (DGT) technique. Lettuce were grown on the As-amended soils following the stabilization of soil labile As after 90 days incubation. Phosphate (P) application generally facilitated plant growth except one grown on P-sufficient soil. Soil labile As concentration increased in all the soils after P application due to a competition effect. Plant As concentration increased in red soils collected from Hunan Province, while decreases were observed in the other soils. Even though, an overall trend of decrease was obtained in As phytoavailability along with the increase of DGT-measured soil labile P/As molar ratio. The functional equation between P/As and As phytoavailability provided a critical value of 1.7, which could be used as a guidance for rational P fertilization, thus avoiding overfertilization. Copyright © 2018 Elsevier Ltd. All rights reserved.

Trans labilization of am(m)ine ligands from platinum(II) complexes by cancer cell extracts.

Science.gov (United States)

Kasherman, Yonit; Sturup, Stefan; Gibson, Dan

2009-03-01

Cisplatin, cis-[Pt(NH(3))(2)Cl(2)], is an effective anticancer agent in wide clinical use whose efficacy is affected by cellular interactions with sulfur-containing nucleophiles. These interactions can potentially enhance the efficacy of the drug by mediating its delivery to nuclear DNA or inactivate the drug by binding to it irreversibly or by labilizing the NH(3) ligands. Despite the potential importance of trans-labilization reactions in the mechanism of action of the drug, few detailed studies on trans labilization of the ammines have been conducted. We used 2D NMR to show that some trans labilization occurs in proliferating cells and that aqueous extracts of cancer cells labilized 20% of the amine ligands of cis-[PtCl(2)((13)CH(3)NH(2))(2)] after a 12-h incubation. Both low molecular mass nucleophiles (less than 3 kDa) and high molecular mass nucleophiles (more than 3 kDa) labilize the amines with similar efficiency. Studies with model compounds show that thiols and thioethers bind to platinum(II) at similar rates, but thioethers are significantly more efficient at labilizing the am(m)ine at lower pH. N-Acetylcysteine is a more efficient trans-labilizer than glutathione, suggesting that the displacement of the amine proceeds through an associative mechanism. The lag time, the time that elapses from the formation of the Pt-S bond till the release of the amine trans to the sulfur, depends on the pH (for thiols), increasing at lower pH. Quantification of the platinum adducts obtained from incubation of cisplatin with cell extracts indicates that two thirds of the platinum is bound to cellular components with molecular mass greater than 3 kDa.

Photo-lability of deep ocean dissolved black carbon

Directory of Open Access Journals (Sweden)

A. Stubbins

2012-05-01

Full Text Available Dissolved black carbon (DBC, defined here as condensed aromatics isolated from seawater via PPL solid phase extraction and quantified as benzenepolycarboxylic acid (BPCA oxidation products, is a significant component of the oceanic dissolved organic carbon (DOC pool. These condensed aromatics are widely distributed in the open ocean and appear to be tens of thousands of years old. As such DBC is regarded as highly refractory. In the current study, the photo-lability of DBC, DOC and coloured dissolved organic matter (CDOM; ultraviolet-visible absorbance were determined over the course of a 28 day irradiation of North Atlantic Deep Water under a solar simulator. During the irradiation DBC fell from 1044 ± 164 nM-C to 55 ± 15 nM-C, a 20-fold decrease in concentration. Dissolved black carbon photo-degradation was more rapid and more extensive than for bulk CDOM and DOC. The concentration of DBC correlated with CDOM absorbance and the quality of DBC indicated by the ratios of different BPCAs correlated with CDOM absorbance spectral slope, suggesting the optical properties of CDOM may provide a proxy for both DBC concentrations and quality in natural waters. Further, the photo-lability of components of the DBC pool increased with their degree of aromatic condensation. These trends indicate that a continuum of compounds of varying photo-lability exists within the marine DOC pool. In this continuum, photo-lability scales with aromatic character, specifically the degree of condensation. Scaling the rapid photo-degradation of DBC to rates of DOC photo-mineralisation for the global ocean leads to an estimated photo-chemical half-life for oceanic DBC of less than 800 years. This is more than an order of magnitude shorter than the apparent age of DBC in the ocean. Consequently, photo-degradation is posited as the primary sink for oceanic DBC and the apparent survival of DBC molecules in the oceans for millennia appears to be facilitated not by their

Microbial control of soil organic matter mineralization responses to labile carbon in subarctic climate change treatments

DEFF Research Database (Denmark)

Rousk, Kathrin; Michelsen, Anders; Rousk, Johannes

2016-01-01

Half the global soil carbon (C) is held in high-latitude systems. Climate change will expose these to warming and a shift towards plant communities with more labile C input. Labile C can also increase the rate of loss of native soil organic matter (SOM); a phenomenon termed ‘priming’. We investig......Half the global soil carbon (C) is held in high-latitude systems. Climate change will expose these to warming and a shift towards plant communities with more labile C input. Labile C can also increase the rate of loss of native soil organic matter (SOM); a phenomenon termed ‘priming’. We...

Post-fire diversity and abundance in pine and eucalipt stands in Portugal: effects of biogeography, topography, forest type and post-fire management

OpenAIRE

Maia, P.; Keizer, J.; Vasques, A.; Abrantes, N.; Roxo, L.; Fernandes, P.; Ferreira, A.; Moreira, F.

2014-01-01

This study concerned the mid-term regeneration of the woody understory vegetation of pure and mixed stands of Pinus pinaster Ait. and Eucalyptus globulus Labill. in northern and central Portugal following wildfires in 2005 and 2006. Pine and eucalypt stands are the most widespread and most fire-prone forest types in Portugal. The main aim was to investigate the importance of biogeography, topography, forest type and post-fire management operations in explaining the patterns in shr...

Sources, lability and solubility of Pb in alluvial soils of the River Trent catchment, U.K

International Nuclear Information System (INIS)

Izquierdo, M.; Tye, A.M.; Chenery, S.R.

2012-01-01

Alluvial soils are reservoirs of metal contaminants such as Pb that originate from many different sources and are integrated temporally and spatially through erosional and depositional processes. In this study the source, lability and solubility of Pb were examined in a range of alluvial soils from the middle and lower River Trent and its tributary the River Dove using Pb isotope apportionment and isotopic dilution. All samples were collected within 10 m of the river bank to represent the soil that is most likely to be remobilised during bank erosion. Paired samples were taken from the topsoil (0–15 cm) and subsoil (35–50 cm) to assess differences with depth. Lead concentrations in soil ranged from 43 to 1282 mg/kg. The lability of soil Pb varied between 9 and 56% of total metal concentration whilst Pb concentrations in pore water varied between 0.2 and 6.5 μg/L. There was little difference in the % Pb lability between paired top and sub soils, possibly because soil characteristics such as pH, iron oxides and clay content were generally similar; a result of the recycling of eroded and deposited soils within the river system. Soil pH was found to be negatively correlated with % Pb lability. Source apportionment using 206 Pb/ 207 Pb and 208 Pb/ 207 Pb ratios showed that the isotopic ratios of Pb in the total, labile and solution pools fitted along a mixing line between Broken Hill Type (‘BHT’) Pb, used as an additive in UK petrol, and the local coal/Southern Pennine ore Pb. Various anomalies were found in the Pb isotopes of the bankside alluvial soils which were explained by point source pollution. Statistically significant differences were found between (i) the isotopic composition of Pb in the total soil pool and the labile/solution pools and (ii) the isotopic composition of Pb in the labile and solution pools, suggesting an enrichment of recent non-Pennine sources of Pb entering the soils in the labile and solution pools. -- Highlights: ► The labile

Childhood Maltreatment, Emotional Lability, and Alcohol Problems in Young Adults At-Risk for ADHD: Testing Moderation and Moderated Moderation.

Science.gov (United States)

Bunford, Nóra; Wymbs, Brian T; Dawson, Anne E; Shorey, Ryan C

2017-01-01

Childhood maltreatment and alcohol problems are common among young adults with attention-deficit hyperactivity disorder (ADHD). However, little is known about the degree to which maltreatment and alcohol problems are associated; potential pertinent mediating or moderating mechanisms, such as emotional lability; and whether this association varies by sex. We examined, in a sample of adults at risk for ADHD (N = 122, 37% male), the association between childhood maltreatment and alcohol problems, whether emotional lability mediated or moderated this association, and whether either role of emotional lability differed between men and women. Emotional lability moderated the association between emotional neglect and alcohol problems; maltreatment increased risk for alcohol problems for those scoring high tovery high on emotional lability, but not for those with very low-moderate levels. The association between emotional abuse and alcohol problems depended both on emotional lability and sex; emotional abuse decreased the risk for alcohol problems among men very low/low on emotional lability, but not for men who were moderate to very high on emotional lability, or for women. These findings have implications for the way in which targeting maltreatment and emotional lability may be incorporated into prevention and intervention programs to prevent alcohol problems among men and women at risk for ADHD.

'Inconstant males' and the maintenance of labile sex expression in subdioecious plants

DEFF Research Database (Denmark)

Ehlers, Bodil; Bataillon, Thomas

2007-01-01

. Depending on the genetics of sex determination, we found pure dioecy, stable subdioecy (trioecy), and situations where inconstant males coexisted with either pure females or pure males. Under selfing and pollen limitation, certain conditions selected for inconstant males which will drive populations......Here, we evaluate the role of pollen limitation and selfing in the maintenance of labile sex expression in subdioecious plant species. We used a literature survey to explore which factors correlated with a significant occurrence of hermaphrodites in dioecious species. We developed models to explore...... the selective maintenance of labile sex expression. The models had similar ecological assumptions but differed in the genetic basis of sex lability. We found that a significant frequency of hermaphrodites was associated with animal pollination, and that hermaphrodites were ‘inconstant' males with perfect...

Lability of soil organic carbon in tropical soils with different clay minerals

DEFF Research Database (Denmark)

Bruun, Thilde Bech; Elberling, Bo; Christensen, Bent Tolstrup

2010-01-01

Soil organic carbon (SOC) storage and turnover is influenced by interactions between organic matter and the mineral soil fraction. However, the influence of clay content and type on SOC turnover rates remains unclear, particularly in tropical soils under natural vegetation. We examined the lability...... of SOC in tropical soils with contrasting clay mineralogy (kaolinite, smectite, allophane and Al-rich chlorite). Soil was sampled from A horizons at six sites in humid tropical areas of Ghana, Malaysian Borneo and the Solomon Islands and separated into fractions above and below 250 µm by wet sieving....... Basal soil respiration rates were determined from bulk soils and soil fractions. Substrate induced respiration rates were determined from soil fractions. SOC lability was significantly influenced by clay mineralogy, but not by clay content when compared across contrasting clay minerals. The lability...

Enhancement of enzymatic saccharification of Eucalyptus globulus: steam explosion versus steam treatment.

Science.gov (United States)

Martin-Sampedro, Raquel; Revilla, Esteban; Villar, Juan C; Eugenio, Maria E

2014-09-01

Steam explosion and steam pre-treatment have proved capable of enhancing enzymatic saccharification of lignocellulosic materials. However, until now, these methods had not been compared under the same operational conditions and using the same raw material. Both pre-treatments lead to increased yields in the saccharification of Eucalyptus globulus; but results have been better with steam pre-treatments, despite the more accessible surface of exploded samples. The reason for this finding could be enzymatic inhibition: steam explosion causes a more extensive extraction of hemicelluloses and releases a greater amount of degradation products which can inhibit enzymatic action. Enzymatic inhibition is also dependent on the amount and chemical structure of lignin, which was also a contributing factor to the lower enzymatic yields obtained with the most severe pre-treatment. Thus, the highest yields (46.7% glucose and 73.4% xylose yields) were obtained after two cycle of steam treatment, of 5 and 3 min, at 183°C. Copyright © 2014 Elsevier Ltd. All rights reserved.

Green Synthesis of Silver Nanoparticles by using Eucalyptus Globulus Leaf Extract

Science.gov (United States)

Balamurugan, Madheswaran; Saravanan, Shanmugam

2017-12-01

A single step eco-friendly, energy efficient and economically scalable green method was employed to synthesize silver nanoparticles. In this work, the synthesis of silver nanoparticles using Eucalyptus globulus leaf extract as reducing and capping agent along with water as solvent at normal room temperature is described. Silver nanoparticles were prepared from aqueous silver nitrate solution by adding the leaf extract. The prepared nanoparticles were characterized by using UV-visible Spectrophotometer, X-ray diffractometer, High Resolution Transmission Electron Microscope (HR-TEM) and Fourier Transform Infrared Spectroscope (FTIS). X-ray diffraction studies brought to light the crystalline nature and the face centered cubic structure of the silver nanoparticles. Using HR-TEM. the nano sizes and morphology of the particles were studied. The mean sizes of the prepared silver nanoparticles ranged from 30 to 36 nm. The density of the particles was tuned by varying the molar ratio of silver nitrate. FTIS studies showed the functional group of organic molecules which were located on the surface of the silver nanoparticles. Originating from the leaf extracts, these organic molecules reduced and capped the particles.

Macrocarpal C isolated from Eucalyptus globulus inhibits dipeptidyl peptidase 4 in an aggregated form.

Science.gov (United States)

Kato, Eisuke; Kawakami, Kazuhiro; Kawabata, Jun

2018-12-01

Dipeptidyl peptidase 4 (DPP-4) inhibitors are used for the treatment of type-2 diabetes mellitus. Various synthetic inhibitors have been developed to date, and plants containing natural DPP-4 inhibitors have also been identified. Here, 13 plant samples were tested for their DPP-4 inhibitory activity. Macrocarpals A-C were isolated from Eucalyptus globulus through activity-guided fractionation and shown to be DPP-4 inhibitors. Of these, macrocarpal C showed the highest inhibitory activity, demonstrating an inhibition curve characterised by a pronounced increase in activity within a narrow concentration range. Evaluation of macrocarpal C solution by turbidity, nuclear magnetic resonance spectroscopy and mass spectrometry indicated its aggregation, which may explain the characteristics of the inhibition curve. These findings will be valuable for further study of potential small molecule DPP-4 inhibitors.

Non-labile silver species in biosolids remain stable throughout 50 years of weathering and ageing

International Nuclear Information System (INIS)

Donner, E.; Scheckel, K.; Sekine, R.; Popelka-Filcoff, R.S.; Bennett, J.W.; Brunetti, G.; Naidu, R.; McGrath, S.P.; Lombi, E.

2015-01-01

Increasing commercial use of nanosilver has focussed attention on the fate of silver (Ag) in the wastewater release pathway. This paper reports the speciation and lability of Ag in archived, stockpiled, and contemporary biosolids from the UK, USA and Australia, and indicates that biosolids Ag concentrations have decreased significantly over recent decades. XANES revealed the importance of reduced-sulfur binding environments for Ag speciation in materials ranging from freshly produced sludge to biosolids weathered under ambient environmental conditions for more than 50 years. Isotopic dilution with 110m Ag showed that Ag was predominantly non-labile in both fresh and aged biosolids (13.7% mean lability), with E-values ranging from 0.3 to 60 mg/kg and 5 mM CaNO 3 extractable Ag from 1.2 to 609 μg/kg (0.002–3.4% of the total Ag). This study indicates that at the time of soil application, biosolids Ag will be predominantly Ag-sulfides and characterised by low isotopic lability. - Highlights: • Biosolids silver (Ag) concentrations appear to have decreased in recent decades. • Ag 2 S dominates Ag speciation in freshly produced sludge. • Ag 2 S is also the dominant species in aged biosolids. • Upon land application biosolids will mainly contain Ag-sulfides and have low isotopic lability. - Analysis of historic and contemporary biosolids from three continents indicated decreasing wastewater silver releases, and non-labile, extremely stable silver speciation

Assessment of Affect Lability: Psychometric Properties of the ALS-18.

Science.gov (United States)

Contardi, Anna; Imperatori, Claudio; Amati, Italia; Balsamo, Michela; Innamorati, Marco

2018-01-01

Affect lability, an important aspect of emotion dysregulation, characterizes several psychiatric conditions. The short Affective Lability Scales (ALS-18) measures three aspects of changeability between euthymia and affect states (Anxiety/Depression, AD; Depression/Elation, DE; and Anger, Ang). The aim of our study was to investigate the psychometric characteristics of an Italian version of the ALS-18 in a sample of adults recruited from the general population. The sample was composed of 494 adults (343 women and 151 men) aged 18 and higher (mean age = 31.73 years, SD = 12.6). All participants were administered a checklist assessing socio-demographic variables, the ALS-18 and measures of depression and difficulties in emotion regulation. Confirmatory factor analyses indicated adequate fit of the three-factor model (RMSEA = 0.061, 95% CI = 0.054/0.069; CFI = 0.99; SRMR = 0.055), and the presence of a higher-order general factor. Internal consistency was satisfactory for all the lower-order dimensions and the general factor (ordinal α > 0.70). The ALS-18 was significantly associated with concurrent measures of depression and difficulties in emotion regulation. These findings indicate that the ALS-18 is a valid and reliable instrument for measuring affect lability, although discriminant validity of subdimensions scores could be problematic.

Assessment of contaminant lability during phytoremediation of polycyclic aromatic hydrocarbon impacted soil

Energy Technology Data Exchange (ETDEWEB)

Zakia D. Parrish; M. Katherine Banks; A. Paul Schwab [Connecticut Agricultural Experiment Station, New Haven, CT (United States). Department of Soil and Water

2005-09-15

Polycyclic aromatic hydrocarbons (PAHs) are recalcitrant compounds, some of which are known carcinogens, often found in high residual soil concentrations at industrial sites. Recent research has confirmed that phytoremediation holds promise as a low-cost treatment method for PAH contaminated soil. In this study, the lability of soil bound PAHs in the rhizosphere was estimated using solid phase extraction resin. An extraction time of 14 days was determined to be appropriate for this study. Resin-extractable PAHs, which are assumed to be more bioavailable, decreased during plant treatments. Significant reductions in the labile concentrations of several PAH compounds occurred over 12 months of plant growth. The differences in concentration between the unplanted and the planted soil indicate that the presence of plant roots, in addition to the passage of time, contributes to reduction in the bioavailability of target PAHs. The lability of sorbed contaminants is modified by the presence of plants. Remediation coupled with plant treatment can change the bioavailability of contaminants in soil.

Assessment of contaminant lability during phytoremediation of polycyclic aromatic hydrocarbon impacted soil

Energy Technology Data Exchange (ETDEWEB)

Parrish, Zakia D. [Department of Soil and Water, Connecticut Agricultural Experiment Station, 123 Huntington Street, New Haven, CT 06511 (United States); Banks, M. Katherine [School of Civil Engineering, Purdue University, 550 Stadium Mall Drive, West Lafayette, IN 47907-2051 (United States)]. E-mail: kbanks@ecn.purdue.edu; Schwab, A. Paul [Department of Agronomy, Purdue University, 915 W. State Street, West Lafayette, IN 47907-2054 (United States)

2005-09-15

Polycyclic aromatic hydrocarbons (PAHs) are recalcitrant compounds, some of which are known carcinogens, often found in high residual soil concentrations at industrial sites. Recent research has confirmed that phytoremediation holds promise as a low-cost treatment method for PAH contaminated soil. In this study, the lability of soil bound PAHs in the rhizosphere was estimated using solid phase extraction resin. An extraction time of 14 days was determined to be appropriate for this study. Resin-extractable PAHs, which are assumed to be more bioavailable, decreased during plant treatments. Significant reductions in the labile concentrations of several PAH compounds occurred over 12 months of plant growth. The differences in concentration between the unplanted and the planted soil indicate that the presence of plant roots, in addition to the passage of time, contributes to reduction in the bioavailability of target PAHs. - The lability of sorbed contaminants is modified by the presence of plants. Remediation coupled with plant treatment can change the bioavailability of contaminants in soil.

Assessment of contaminant lability during phytoremediation of polycyclic aromatic hydrocarbon impacted soil

International Nuclear Information System (INIS)

Parrish, Zakia D.; Banks, M. Katherine; Schwab, A. Paul

2005-01-01

Polycyclic aromatic hydrocarbons (PAHs) are recalcitrant compounds, some of which are known carcinogens, often found in high residual soil concentrations at industrial sites. Recent research has confirmed that phytoremediation holds promise as a low-cost treatment method for PAH contaminated soil. In this study, the lability of soil bound PAHs in the rhizosphere was estimated using solid phase extraction resin. An extraction time of 14 days was determined to be appropriate for this study. Resin-extractable PAHs, which are assumed to be more bioavailable, decreased during plant treatments. Significant reductions in the labile concentrations of several PAH compounds occurred over 12 months of plant growth. The differences in concentration between the unplanted and the planted soil indicate that the presence of plant roots, in addition to the passage of time, contributes to reduction in the bioavailability of target PAHs. - The lability of sorbed contaminants is modified by the presence of plants. Remediation coupled with plant treatment can change the bioavailability of contaminants in soil

Steam torrefaction of Eucalyptus globulus for producing black pellets: A pilot-scale experience.

Science.gov (United States)

Arteaga-Pérez, Luis E; Grandón, Héctor; Flores, Mauricio; Segura, Cristina; Kelley, Stephen S

2017-08-01

Steam torrefaction of Eucalyptus globulus was performed at temperatures between 245°C and 265°C in a 100kg/h pilot plant. Torrefied biomass was then pelletized in a 300kg/h unit and the pellets were subject to durability, density and combustion tests. The structural changes measured with FTIR were studied along with the combustion behavior of the materials. Compositional analysis showed that increasing the torrefaction temperature reduced both hemicellulose fraction and overall mass yield (MY). Furthermore, there was a linear relationship between the energy yield (EY) and mass yield (EY=[1.04-0.9(1-MY)]) for these samples. The ignition and comprehensive indexes confirmed that the stability of the torrefied biomass in a combustion environment was higher than for untreated biomass. Finally, pellets showed high durability (98%), and had an energy density (13-14GJ/m 3 ), which is comparable to low-rank coals. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sources, lability and solubility of Pb in alluvial soils of the River Trent catchment, U.K.

Science.gov (United States)

Izquierdo, M; Tye, A M; Chenery, S R

2012-09-01

Alluvial soils are reservoirs of metal contaminants such as Pb that originate from many different sources and are integrated temporally and spatially through erosional and depositional processes. In this study the source, lability and solubility of Pb were examined in a range of alluvial soils from the middle and lower River Trent and its tributary the River Dove using Pb isotope apportionment and isotopic dilution. All samples were collected within 10 m of the river bank to represent the soil that is most likely to be remobilised during bank erosion. Paired samples were taken from the topsoil (0-15 cm) and subsoil (35-50 cm) to assess differences with depth. Lead concentrations in soil ranged from 43 to 1282 mg/kg. The lability of soil Pb varied between 9 and 56% of total metal concentration whilst Pb concentrations in pore water varied between 0.2 and 6.5 μg/L. There was little difference in the % Pb lability between paired top and sub soils, possibly because soil characteristics such as pH, iron oxides and clay content were generally similar; a result of the recycling of eroded and deposited soils within the river system. Soil pH was found to be negatively correlated with % Pb lability. Source apportionment using (206)Pb/(207)Pb and (208)Pb/(207)Pb ratios showed that the isotopic ratios of Pb in the total, labile and solution pools fitted along a mixing line between Broken Hill Type ('BHT') Pb, used as an additive in UK petrol, and the local coal/Southern Pennine ore Pb. Various anomalies were found in the Pb isotopes of the bankside alluvial soils which were explained by point source pollution. Statistically significant differences were found between (i) the isotopic composition of Pb in the total soil pool and the labile/solution pools and (ii) the isotopic composition of Pb in the labile and solution pools, suggesting an enrichment of recent non-Pennine sources of Pb entering the soils in the labile and solution pools. Copyright © 2012 Natural Environment

Lability criteria for metal complexes in micro-electrode voltammetry

NARCIS (Netherlands)

Leeuwen, van H.P.; Pinheiro, J.P.

1999-01-01

Theoretical expressions are derived for the voltammetric lability criteria of metal complexes in the micro-electrode regime. The treatment includes three limiting situations: (i) the macro-electrode limit, where both the diffusion layer and the dissociation reaction layer are linear; (ii) an

Effects of wetland recovery on soil labile carbon and nitrogen in the Sanjiang Plain.

Science.gov (United States)

Huang, Jingyu; Song, Changchun; Nkrumah, Philip Nti

2013-07-01

Soil management significantly affects the soil labile organic factors. Understanding carbon and nitrogen dynamics is extremely helpful in conducting research on active carbon and nitrogen components for different kinds of soil management. In this paper, we examined the changes in microbial biomass carbon (MBC), microbial biomass nitrogen (MBN), dissolved organic carbon (DOC), and dissolved organic nitrogen (DON) to assess the effect and mechanisms of land types, organic input, soil respiration, microbial species, and vegetation recovery under Deyeuxia angustifolia freshwater marshes (DAMs) and recovered freshwater marsh (RFM) in the Sanjiang Plain, Northeast China. Identifying the relationship among the dynamics of labile carbon, nitrogen, and soil qualification mechanism using different land management practices is therefore important. Cultivation and land use affect intensely the DOC, DON, MBC, and MBN in the soil. After DAM soil tillage, the DOC, DON, MBC, and MBN at the surface of the agricultural soil layer declined significantly. In contrast, their recovery was significant in the RFM surface soil. A long time was needed for the concentration of cultivated soil total organic carbon and total nitrogen to be restored to the wetland level. The labile carbon and nitrogen fractions can reach a level similar to that of the wetland within a short time. Typical wetland ecosystem signs, such as vegetation, microbes, and animals, can be recovered by soil labile carbon and nitrogen fraction restoration. In this paper, the D. angustifolia biomass attained natural wetland level after 8 years, indicating that wetland soil labile fractions can support wetland eco-function in a short period of time (4 to 8 years) for reconstructed wetland under suitable environmental conditions.

Estimating soil labile organic carbon and potential turnover rates using a sequential fumigation–incubation procedure.

Science.gov (United States)

X.M. Zoua; H.H. Ruanc; Y. Fua; X.D. Yanga; L.Q. Sha

2005-01-01

Labile carbon is the fraction of soil organic carbon with most rapid turnover times and its oxidation drives the flux of CO2 between soils and atmosphere. Available chemical and physical fractionation methods for estimating soil labile organic carbon are indirect and lack a clear biological definition. We have modified the well-established Jenkinson and Powlson’s...

High-resolution imaging of labile phosphorus and its relationship with iron redox state in lake sediments

DEFF Research Database (Denmark)

Gao, Yulu; Liang, Tao; Tian, Shuhan

2016-01-01

a regional summer algal bloom. Two-dimensional distributions of labile P in sediments were imaged with the Zr-Oxide DGT without destruction of the original structure of the sediment layer at four sites of the lake. The concentration of DGT-labile P in the sediments, ranging from 0.007 to 0.206 mg L(-1......), was highly heterogeneous across the profiles. The values of apparent diffusion flux (Fd) and release flux (Fr) of P varied between -0.027-0.197 mg m(-2) d(-1) and 0.037-0.332 mg m(-2) d(-1), respectively. Labile P showed a high and positive correlation (p

Comparative gas chromatography-mass spectroscopy, Fourier transform infrared spectroscopy, and high-performance liquid chromatography analysis of essential oils extracted using 4 methods from the leaves of Eucalyptus globulus L.

Directory of Open Access Journals (Sweden)

Yasmeen Khan

2016-01-01

Full Text Available Background: Eucalyptus globulus L. (family, Myrtaceae is one of the world′s most widely planted genera. E. globulus L., commonly referred to as Tasmanian blue gum, is a fast growing, evergreen tree, native to Tasmania and South-East Australia. Apart from its extensive use in pulp industry, it is also produces Oleum Eucalypti (eucalyptus oil that is extracted on commercial scale in many countries such as China, India, South Africa, Portugal, Brazil, and Tasmania, as a raw material in perfumery, cosmetics, food beverage, aromatherapy, and phytotherapy. Materials and Methods: Traditional hydrodistillation (HD, solvent extraction (SE, ultrasonication (US, and supercritical fluid extraction (SFE were conducted for the extraction of essential oil from the leaves of E. globulus. Each oil was evaluated in terms of high-performance liquid chromatography (HPTLC and Fourier transform infrared spectroscopy (FTIR fingerprinting with qualitative and semi-quantitative composition of the isolated essential oil by gas chromatography-mass spectroscopy (GCMS, the extract yield of essential oil was 2.60%, 2.2%, 2.0%, and 3.6% v/w, respectively, for HD, SE, US, and SFE. Results: A total of 53 compounds were identified by GCMS. Comparative analysis indicated that SFE was favorable for extraction of monoterpene hydrocarbon, sesquiterpene hydrocarbon, and oxygenated sesquiterpene hydrocarbon. HD, SE, and US had certain advantages in the extraction of aliphatic saturated hydrocarbons organic acid and esters. Overlay, FTIR spectra of oil samples obtained by four extraction methods were superimposed with each other showing similar components. The maximum separation of compound seen at 254 nm and lesser at 366 nm by HPTLC fingerprinting which again showed superimposed chromatograms. Conclusion: It is concluded that different extraction method may lead to different yields of essential oils where the choice of appropriate method is very important to obtained more desired

Kraft pulping and ECF bleaching of Eucalyptus globulus pretreated by the white-rot fungus Ceriporiopsis subvermispora - doi: 10.4025/actascitechnol.v34i3.12410

Directory of Open Access Journals (Sweden)

Claudio Salazar

2012-05-01

Full Text Available Eucalyptus globulus wood chips were decayed by the lignin-degrading fungus Ceriporiopsis subvermispora as a pretreatment step before kraft pulping. Weight and component losses of wood after the biotreatment were the following: weight (5%, glucans (1.5%, xylans (4.3%, lignin (5.7% and extractives (57.5%. The residual amount of lignin (expressed by the kappa number in pulps from biotreated wood chips was lower than that of pulps from the undecayed control. Depending on the delignification degree, kraft biopulps presented similar or up to 4% increase in pulp yield and 20% less hexenuronic acids (HexA than control pulps. The extended delignification with O2 decreases approximately 50% of the kappa number of the pulps and increases brightness, but had no effect in HexA reduction. The bleaching steps with chlorine dioxide (D0ED1 sequence decreased the kappa number up to 97%, increased pulp brightness up to 84% ISO and decreased HexA amount up to 91%. The use of C. subvermispora in biopulping of E. globulus generated important benefits during the production of kraft pulps that are reflected in a high pulp yield, low residual lignin content, low HexA amount, high brightness and viscosity of the biopulps as compared with pulps produced from untreated wood chips.

Supercritical Fluid Extraction of Eucalyptus globulus Bark—A Promising Approach for Triterpenoid Production

Science.gov (United States)

Domingues, Rui M. A.; Oliveira, Eduardo L. G.; Freire, Carmen S. R.; Couto, Ricardo M.; Simões, Pedro C.; Neto, Carlos P.; Silvestre, Armando J. D.; Silva, Carlos M.

2012-01-01

Eucalyptus bark contains significant amounts of triterpenoids with demonstrated bioactivity, namely triterpenic acids and their acetyl derivatives (ursolic, betulinic, oleanolic, betulonic, 3-acetylursolic, and 3-acetyloleanolic acids). In this work, the supercritical fluid extraction (SFE) of Eucalyptus globulus deciduous bark was carried out with pure and modified carbon dioxide to recover this fraction, and the results were compared with those obtained by Soxhlet extraction with dichloromethane. The effects of pressure (100–200 bar), co-solvent (ethanol) content (0, 5 and 8% wt), and multistep operation were studied in order to evaluate the applicability of SFE for their selective and efficient production. The individual extraction curves of the main families of compounds were measured, and the extracts analyzed by GC-MS. Results pointed out the influence of pressure and the important role played by the co-solvent. Ethanol can be used with advantage, since its effect is more important than increasing pressure by several tens of bar. At 160 bar and 40 °C, the introduction of 8% (wt) of ethanol greatly improves the yield of triterpenoids more than threefold. PMID:22837719

BAYESIAN PREDICTION OF GENETIC PARAMETERS IN Eucalyptus globulus CLONES UNDER WATER SUPPLY CONDITIONS

Directory of Open Access Journals (Sweden)

Freddy Mora

2013-06-01

Full Text Available http://dx.doi.org/10.5902/198050989297A Bayesian analysis of genetic parameters for growth traits at twelve months after planting was carried out in twenty nine Eucalyptus globulus clones in southern Chile. Two different environmental conditions were considered: 1 Non-irrigation and; 2 Plants were irrigated with a localized irrigation system. The Bayesian approach was performed using Gibbs sampling algorithm in a clone-environment interaction model. Inheritability values ​​were high in the water supply condition (posterior mode: H2=0.41, 0.36 and 0.39 for height, diameter and sectional area, respectively, while in the environment without irrigation, the inheritabilities were significantly lower, which was confirmed by the Bayesian credible intervals (95% probability. The posterior mode of the genetic correlation between sites was positive and high for all traits (r=0.7, 0.65 and 0.8, for height, diameter and sectional area, respectively and according to the credible interval, it was statistically different from zero, indicating a non-significant interaction.

Biotic and abiotic controls on diurnal fluctuations in labile soil phosphorus of a wet tropical forest.

Science.gov (United States)

Vandecar, Karen L; Lawrence, Deborah; Wood, Tana; Oberbauer, Steven F; Das, Rishiraj; Tully, Katherine; Schwendenmann, Luitgard

2009-09-01

The productivity of many tropical wet forests is generally limited by bioavailable phosphorus (P). Microbial activity is a key regulator of P availability in that it determines both the supply of P through organic matter decomposition and the depletion of bioavailable P through microbial uptake. Both microbial uptake and mineralization occur rapidly, and their net effect on P availability varies with soil moisture, temperature, and soil organic matter quantity and quality. Exploring the mechanisms driving P availability at fine temporal scales can provide insight into the coupling of carbon, water, and nutrient cycles, and ultimately, the response of tropical forests to climate change. Despite the recognized importance of P cycling to the dynamics of wet tropical forests and their potential sensitivity to short-term fluctuations in bioavailable P, the diurnal pattern of P remains poorly understood. This study quantifies diurnal fluctuations in labile soil P and evaluates the importance of biotic and abiotic factors in driving these patterns. To this end, measurements of labile P were made every other hour in a Costa Rican wet tropical forest oxisol. Spatial and temporal variation in Bray-extractable P were investigated in relation to ecosystem carbon flux, soil CO2 efflux, soil moisture, soil temperature, solar radiation, and sap-flow velocity. Spatially averaged bi-hourly (every two hours) labile P ranged from 0.88 to 2.48 microg/g across days. The amplitude in labile P throughout the day was 0.61-0.82 microg/g (41-54% of mean P concentrations) and was characterized by a bimodal pattern with a decrease at midday. Labile P increased with soil CO2 efflux and soil temperature and declined with increasing sap flow and solar radiation. Together, soil CO2 efflux, soil temperature, and sap flow explained 86% of variation in labile P.

Measurement of labile copper in wine by medium exchange stripping potentiometry utilising screen printed carbon electrodes.

Science.gov (United States)

Clark, Andrew C; Kontoudakis, Nikolaos; Barril, Celia; Schmidtke, Leigh M; Scollary, Geoffrey R

2016-07-01

The presence of copper in wine is known to impact the reductive, oxidative and colloidal stability of wine, and techniques enabling measurement of different forms of copper in wine are of particular interest in understanding these spoilage processes. Electrochemical stripping techniques developed to date require significant pretreatment of wine, potentially disturbing the copper binding equilibria. A thin mercury film on a screen printed carbon electrode was utilised in a flow system for the direct analysis of labile copper in red and white wine by constant current stripping potentiometry with medium exchange. Under the optimised conditions, including an enrichment time of 500s and constant current of 1.0μA, the response range was linear from 0.015 to 0.200mg/L. The analysis of 52 red and white wines showed that this technique generally provided lower labile copper concentrations than reported for batch measurement by related techniques. Studies in a model system and in finished wines showed that the copper sulfide was not measured as labile copper, and that loss of hydrogen sulfide via volatilisation induced an increase in labile copper within the model wine system. Copyright © 2016 Elsevier B.V. All rights reserved.

Development and Lability in the Parent-Child Relationship During Adolescence: Associations With Pubertal Timing and Tempo

Science.gov (United States)

Marceau, Kristine; Ram, Nilam; Susman, Elizabeth

2014-01-01

Adolescents' and parents' reactions to pubertal development are hypothesized to contribute to changes in family dynamics. Using 7-year longitudinal data from the NICHD-SECCYD (488 boys, 475 girls) we examined relations between pubertal development (timing, tempo) and trajectories (developmental change and year-to-year lability) of parent-child conflict and closeness from age 8.5 to 15.5 years. Changes were mostly characterized by year-to-year fluctuations – lability. Parent-child conflict increased and closeness decreased some with age. Pubertal timing and tempo were more consistently associated with lability in parent-child relationships than with long-term trends, although faster tempo was associated with steeper decreases in parent-child closeness. Findings provide a platform for examining how puberty contributes to both long-term and transient changes in adolescents' relationships and adjustment. PMID:26321856

Human acid-labile subunit deficiency: clinical, endocrine and metabolic consequences

NARCIS (Netherlands)

Domené, Horacio M.; Hwa, Vivian; Argente, Jesús; Wit, Jan M.; Wit, Jaan M.; Camacho-Hübner, Cecilia; Jasper, Héctor G.; Pozo, Jesús; van Duyvenvoorde, Hermine A.; Yakar, Shoshana; Fofanova-Gambetti, Olga V.; Rosenfeld, Ron G.; Scaglia, Paula A.; Bengolea, Sonia V.; Lteif, Aida; Kirmani, Salman; Mahmud, Farid H.; Frystyk, Jan; Hermus, Ad; Twickler, T. B.; Kempers, Marlies J. E.; Barrios, Vicente; Martos-Moreno, Gabriel A.; David, Alessia; Rose, Stephen

2009-01-01

The majority of insulin-like growth factor (IGF)-I and IGF-II circulate in the serum as a complex with the insulin-like growth factor binding protein (IGFBP)-3 or IGFBP-5, and an acid-labile subunit (ALS). The function of ALS is to prolong the half-life of the IGF-I-IGFBP-3/IGFBP-5 binary complexes.

Non-labile tritium in Savannah River Plant pine trees

International Nuclear Information System (INIS)

Sanders, S.M. Jr.

1976-06-01

Non-labile tritium bound in cellulose of pine trees was measured to learn about the effects and fate of tritium contributed to the environment by the Savannah River Plant (SRP). An estimation of the regional inventory and the distance tritium can be observed from SRP was desired because tritium is a major component of the radioactivity released by SRP, and as the oxide, it readily disperses in the environment

Establishing fuelwood plantation and fire wood tree crop performance on the highlands of Ethiopia: The case of Eucalyptus globulus Labill.ssp globulus

Energy Technology Data Exchange (ETDEWEB)

Mehari, A.

1997-11-01

This study reviews reasons for the establishment of fuelwood plantation and use of fuelwood in Ethiopia. The present and future status of fire wood and the environmental degradation and related consequences are also reviewed. 138 refs, 22 figs, 6 tabs

An anaerobic incubation study of metal lability in drinking water treatment residue with implications for practical reuse.

Science.gov (United States)

Wang, Changhui; Yuan, Nannan; Pei, Yuansheng

2014-06-15

Drinking water treatment residue (WTR) is an inevitable by-product generated during the treatment of drinking water with coagulating agents. The beneficial reuse of WTR as an amendment for environmental remediation has attracted growing interest. In this work, we investigated the lability of Al, As, Ba, Be, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, Sr, V and Zn in Fe/Al hydroxide-comprised WTR based on a 180-day anaerobic incubation test using fractionation, in vitro digestion and a toxicity characteristic leaching procedure. The results indicated that most metals in the WTR were stable during anaerobic incubation and that the WTR before and after incubation could be considered non-hazardous in terms of leachable metal contents according to US EPA Method 1311. However, the lability of certain metals in the WTR after incubation increased substantially, especially Mn, which may be due to the reduction effect. Therefore, although there is no evidence presented to restrict the use of WTR in the field, the lability of metals (especially Mn) in WTR requires further assessment prior to field application. In addition, fractionation (e.g., BCR) is recommended for use to determine the potential lability of metals under various conditions. Copyright © 2014 Elsevier B.V. All rights reserved.

Strand breaks and alkali-labile bonds induced by ultraviolet light in DNA with 5-bromouracil in vivo.

Science.gov (United States)

Krasin, F; Hutchinson, F

1978-01-01

Supercircular gamma phage DNA with 10 bromouracils/100 thymine bases, irradiated with 313 nm light in Tris buffer and sedimented on alkaline and neutral gradients, showed 4.6 alkali-labile bonds per true single-strand break, in agreement with Hewitt and Marburger (1975 Photochem. Photobiol. 21:413). The same DNA irradiated in Escherichia coli host cells showed about the same number of breaks in alkaline gradients for equal fluence, but only 0.5 alkali-labile bond per true break. Similarly, E. coli DNA with bromouracil irradiated in the cells showed only 10--20% more breaks when denatured with 0.1 M NaOH than under neutral conditions with 9 M sodium perchlorate at 50 degrees C. These results show that true single-strand breaks occur more frequently than alkali-labile bonds after ultraviolet irradiation of DNA containing bromouracil in cells. PMID:367462

Litter production and decomposition in Eucalyptus urophylla x Eucalyptus globulus maidenii stand

Directory of Open Access Journals (Sweden)

Mauro Valdir Schumacher

2013-09-01

Full Text Available he sustainable wood production in commercial plantations requires knowledge of the nutrient cycling process, which also involves the production and decomposition of litter. This study verified the influence of climatic variables on litter production and t evaluated the rate of leaf litter decomposition in a stand of Eucalyptus urophylla x E. globulus maidenii. There were installed 4 plots of 20 m x 20 m, in each plot four litter traps to collect leaves were placed, thin branches and miscellaneous, beside this, each plot received 3 areas for coarse branches collection. The litter collected was used to calculate the deposition and the correlation between climate variables and deposition. The climatic variables used, on a monthly basis, were average temperature, average maximum temperature, average minimum temperature, rainfall, relative humidity, average wind speed, average solar radiation and average evapotranspiration, both supplied by an experimental station. For evaluation of the litter decomposition rate, four square samples of 0.25 m side in each plot were randomly collected and used for determining the decay coefficient (K, half life (t0,5 and decomposition time of 95% of litter (t0,95 . The monthly litter production was weakly correlated with climatic variables and the annual production was 7.4 Mg ha-1, with leaves as the major fraction (60%. The litter decomposition rate was considered slow.

Atividade ovicida e larvicida in vitro do óleo essencial de Eucalyptus globulus sobre Haemonchus contortus Ovicidal and larvicidal activity in vitro of Eucalyptus globulus essential oils on Haemonchus contortus

Directory of Open Access Journals (Sweden)

Iara T. F. Macedo

2009-09-01

Full Text Available O objetivo deste trabalho foi avaliar o efeito do óleo essencial de Eucalyptus globulus (OEEG sobre a eclosão e desenvolvimento de larvas de Haemonchus contortus. A determinação da composição química do OEEG foi feita por meio de cromatografia gasosa acoplada à espectrometria de massa. No teste de eclosão de ovos (TEO, utilizaram-se as concentrações 21,75; 17,4; 8,7; 5,43 e 2,71 mg.mL-1; e no de desenvolvimento larvar (TDL as concentrações foram 43,5; 21,75; 10,87; 5,43 e 2,71 mg.mL-1. Cada ensaio foi acompanhado por um controle positivo, 0,02 mg.mL-1 tiabendazol, no TEO e 0,008 mg.mL-1 ivermectina no TDL, e por um controle negativo com o diluente Tween 80 (3%. A eficácia máxima obtida pelo OEEG sobre ovos foi de 99,3% na concentração de 21,75 mg.mL-1 e, sobre larvas, 98,7% na concentração de 43,5 mg.mL-1. A concentração do OEEG, que inviabilizou 50% dos ovos e das larvas do parasito, foi de 8,3 e 6,92 mg.mL-1, respectivamente. A análise química do óleo identificou como principal componente o monoterpeno 1,8-cineol. O OEEG apresentou atividade ovicida e larvicida in vitro sobre H. contortus, determinando um bom potencial para utilização no controle de nematóides gastrintestinais de ovinos e caprinos.The objective of this work was to evaluate ovicidal and larvicidal effects of Eucalyptus globulus essential oil (EGEO on Haemonchus contortus. The chemical composition determination of EGEO was through gas chromatography and mass spectrometry. Egg hatch test (EHT was performed in concentrations 21.75; 17.4; 8.7; 5.43 e 2.71 mg.mL-1. In larval development test (LDT were used the concentrations 43.5; 21.75; 10.87; 5.43 e 2.71 mg.mL-1. Each trial was conducted by negative control with Tween 80 (3% and positive control, 0.02 mg.mL -1 of thiabendazole in EHT and 0.008 mg.mL-1 of ivermectin in LDT. The maximum effectiveness of EGEO on eggs was 99.3% in concentration of 21.75 mg.mL-1 and on larvae was 98.7% in concentration 43

Cu lability and bioavailability in an urban stream during baseflow versus stormflow

Science.gov (United States)

Vadas, T.; Luan, H.

2012-12-01

Urban streams are dynamic systems with many anthropogenic inputs and stressors. Existing contaminant inputs are regulated through total maximum daily loads. Techniques for assessing that load are based on a combination of acute and chronic water quality criteria, biotic ligand models, and physical, chemical and biological assessments. In addition, the apportionment of reduction in load to different sources is based on total mass and not, for example, on bioavailable fraction. Our understanding of the impact of different metal inputs to stream impairment is limited. Free metal ions are understood to play a role in direct cellular uptake, but metal speciation (e.g. free metal, labile metals, or size fractionated) is relevant to more complex stream food webs. As part of an ongoing study, this work examines dissolved and particulate Cu concentrations in the Hockanum River, Vernon, CT situated in a developed watershed. Stream samples were taken during baseflow as well as stormflow upstream and downstream of wastewater treatment plant and stormwater runoff inputs. In addition, diffusive gradient in thin-film (DGT) devices which measure labile metal concentrations and cultured periphyton were used to examine bioavailable fractions. Total and filtered Cu concentrations ranged from about 1.3 to 10.7 μg/L, and 0.9 to 5.1 μg/L, respectively. Cu concentrations always increased downstream of the wastewater treatment plant by about 1.1-2 times, and effluent accounted for about 30% of baseflow. Generally, small increases (sites downstream from the wastewater treatment plant downstream sampling point, suggesting contributions from sediment resuspension. DGT measured concentrations represented 30 to 70% of dissolved Cu concentrations, and that percentage increased in the days following a storm, suggesting more labile Cu compounds remained in the water column longer. Whereas solution metal concentrations in stormwater influenced reaches did not largely change upstream versus

Labile/inert metal species in aquatic humic substances: an ion-exchange study

International Nuclear Information System (INIS)

Burba, P.

1994-01-01

An ion-exchange procedure has been developed for the analytical fractionation of metals (e.g. Al, Co, Cu, Fe, Mn, Ni, Pb, Zn) forming labile/inert complexes with aquatic humic substances (HS) isolated (XAD 2, XAD 8, ultrafiltration) from bog, forest, ground and lake water. Using 1-(2-hydroxyphenylazo)-2-naphthol groups immobilized on cellulose (Cellulose HYPHAN TM ) as chelating collector (batch and column procedure, resp.) for reactive metal fractions in dissolved HS, the kinetics and the degree of separation (referred to the total metal content) serve for the operational characterization of the metal lability. According to the separation kinetics (96 h), mostly the reactivity order Mn > Zn > Co > Pb > Ni > Cu >> Al > Fe is observed for the above metals in HS, resulting in recoveries of > 98% for Mn and Zn, but strongly varying for the other metals (e.g., 44-95% Cu, 18-84% Fe). (orig.)

Plasma arc cutting: speed and cut quality

International Nuclear Information System (INIS)

Nemchinsky, V A; Severance, W S

2009-01-01

When cutting metal with plasma arc cutting, the walls of the cut are narrower at the bottom than at the top. This lack of squareness increases as the cutting speed increases. A model of this phenomenon, affecting cut quality, is suggested. A thin liquid layer, which separates the plasma from the solid metal to be melted, plays a key role in the suggested model. This layer decreases heat transfer from the plasma to the solid metal; the decrease is more pronounced the higher the speed and the thicker the liquid metal layer. Since the layer is thicker at the bottom of the cut, the heat transfer effectiveness is lower at the bottom. The decrease in heat transfer effectiveness is compensated by the narrowness of the cut. The suggested model allows one to calculate the profile of the cut. The result of the calculations of the cutting speeds for plates of various thicknesses, at which the squareness of the cut is acceptable, agrees well with the speeds recommended by manufacturers. The second effect considered in the paper is the deflection of the plasma jet from the vertical at a high cutting speed. A qualitative explanation of this phenomenon is given. We believe the considerations of this paper are pertinent to other types of cutting with moving heat sources.

Cutting

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Cutting KidsHealth / For Teens / Cutting What's in this article? ... Getting Help Print en español Cortarse What Is Cutting? Emma's mom first noticed the cuts when Emma ...

Molecular insights into the microbial formation of marine dissolved organic matter: recalcitrant or labile?

Science.gov (United States)

Koch, B. P.; Kattner, G.; Witt, M.; Passow, U.

2014-08-01

The degradation of marine dissolved organic matter (DOM) is an important control variable in the global carbon cycle. For our understanding of the kinetics of organic matter cycling in the ocean, it is crucial to achieve a mechanistic and molecular understanding of its transformation processes. A long-term microbial experiment was performed to follow the production of non-labile DOM by marine bacteria. Two different glucose concentrations and dissolved algal exudates were used as substrates. We monitored the bacterial abundance, concentrations of dissolved and particulate organic carbon (DOC, POC), nutrients, amino acids and transparent exopolymer particles (TEP) for 2 years. The molecular characterization of extracted DOM was performed by ultrahigh resolution Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) after 70 days and after ∼2 years of incubation. Although glucose quickly degraded, a non-labile DOC background (5-9% of the initial DOC) was generated in the glucose incubations. Only 20% of the organic carbon from the algal exudate degraded within the 2 years of incubation. The degradation rates for the non-labile DOC background in the different treatments varied between 1 and 11 μmol DOC L-1 year-1. Transparent exopolymer particles, which are released by microorganisms, were produced during glucose degradation but decreased back to half of the maximum concentration within less than 3 weeks (degradation rate: 25 μg xanthan gum equivalents L-1 d-1) and were below detection in all treatments after 2 years. Additional glucose was added after 2 years to test whether labile substrate can promote the degradation of background DOC (co-metabolism; priming effect). A priming effect was not observed but the glucose addition led to a slight increase of background DOC. The molecular analysis demonstrated that DOM generated during glucose degradation differed appreciably from DOM transformed during the degradation of the algal exudates. Our

Microbial control of soil organic matter mineralization responses to labile carbon in subarctic climate change treatments.

Science.gov (United States)

Rousk, Kathrin; Michelsen, Anders; Rousk, Johannes

2016-12-01

Half the global soil carbon (C) is held in high-latitude systems. Climate change will expose these to warming and a shift towards plant communities with more labile C input. Labile C can also increase the rate of loss of native soil organic matter (SOM); a phenomenon termed 'priming'. We investigated how warming (+1.1 °C over ambient using open top chambers) and litter addition (90 g m -2  yr -1 ) treatments in the subarctic influenced the susceptibility of SOM mineralization to priming, and its microbial underpinnings. Labile C appeared to inhibit the mineralization of C from SOM by up to 60% within hours. In contrast, the mineralization of N from SOM was stimulated by up to 300%. These responses occurred rapidly and were unrelated to microbial successional dynamics, suggesting catabolic responses. Considered separately, the labile C inhibited C mineralization is compatible with previously reported findings termed 'preferential substrate utilization' or 'negative apparent priming', while the stimulated N mineralization responses echo recent reports of 'real priming' of SOM mineralization. However, C and N mineralization responses derived from the same SOM source must be interpreted together: This suggested that the microbial SOM-use decreased in magnitude and shifted to components richer in N. This finding highlights that only considering SOM in terms of C may be simplistic, and will not capture all changes in SOM decomposition. The selective mining for N increased in climate change treatments with higher fungal dominance. In conclusion, labile C appeared to trigger catabolic responses of the resident microbial community that shifted the SOM mining to N-rich components; an effect that increased with higher fungal dominance. Extrapolating from these findings, the predicted shrub expansion in the subarctic could result in an altered microbial use of SOM, selectively mining it for N-rich components, and leading to a reduced total SOM-use. © 2016 John Wiley

Trauma exposure and heavy drinking and drug use among college students: Identifying the roles of negative and positive affect lability in a daily diary study.

Science.gov (United States)

Weiss, Nicole H; Bold, Krysten W; Contractor, Ateka A; Sullivan, Tami P; Armeli, Stephen; Tennen, Howard

2018-04-01

Trauma exposure is linked to heavy drinking and drug use among college students. Extant research reveals positive associations between negative affect lability and both trauma exposure and alcohol use. This study aimed to extend past research by using daily diary methods to test whether (a) individuals with (versus without) trauma exposure experience greater negative and positive affect lability, (b) negative and positive affect lability are associated with heavy drinking and drug use, and (c) negative and positive affect lability mediate the relations between trauma exposure and heavy drinking and drug use. Participants were 1640 college students (M age=19.2, 54% female, 80% European American) who provided daily diary data for 30days via online surveys. Daily diaries assessed negative and positive affect and substance use (i.e., percent days of heavy drinking, percent days of drug use, total number of drugs used). Individuals with (versus without) a history of trauma exposure demonstrated higher levels of negative and positive affect lability. Negative, but not positive, affect lability was associated with percent days of heavy drinking, percent days of drug use, and total number of drugs used, and mediated the associations between trauma exposure and heavy drinking and drug use outcomes. Findings provide support for the underlying role of negative affect lability in the relations between trauma exposure and heavy drinking and drug use among college students, suggesting that treatments targeting negative affect lability may potentially serve to reduce heavy drinking and drug use among trauma-exposed college students. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lability of Nanoparticulate Metal Complexes at a Macroscopic Metal Responsive (Bio)interface

NARCIS (Netherlands)

Duval, Jérôme F.L.; Town, Raewyn M.; Leeuwen, Van Herman P.

2018-01-01

The lability of metal complexes expresses the extent of the dissociative contribution of the complex species to the flux of metal ions toward a macroscopic metal-responsive (bio)interface, for example, an electrodic sensor or an organism. While the case of molecular ligands is well-established, it

Determination of cut front position in laser cutting

Science.gov (United States)

Pereira, M.; Thombansen, U.

2016-07-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable.

[Impact of Land Utilization Pattern on Distributing Characters of Labile Organic Carbon in Soil Aggregates in Jinyun Mountain].

Science.gov (United States)

Li, Rui; Jiang, Chang-sheng; Hao, Qing-ju

2015-09-01

Four land utilization patterns were selected for this study in Jinyun mountain, including subtropical evergreen broad-leaved forest (abbreviation: forest), sloping farmland, orchard and abandoned land. Soil samples were taken every 10 cm in the depth of 60 cm soil and proportions of large macroaggregates (> 2 mm), small macroaggregates (0. 25-2 mm), microaggregates (0. 053 - 0. 25 mm) and silt + clay (organic carbon and labile organic carbon in each aggregate fraction and analyze impacts of land uses on organic carbon and labile organic carbon of soil aggregates. LOC content of four soil aggregates were significantly reduced with the increase of soil depth; in layers of 0-60 cm soil depth, our results showed that LOC contents of forest and abandoned land were higher than orchard and sloping farmland. Reserves of labile organic carbon were estimated by the same soil quality, it revealed that forest (3. 68 Mg.hm-2) > abandoned land (1. 73 Mg.hm-2) > orchard (1. 43 Mg.hm-2) >sloping farmland (0.54 Mg.hm-2) in large macroaggregates, abandoned land (7.77, 5. 01 Mg.hm-2) > forest (4. 96, 2.71 Mg.hm-2) > orchard (3. 33, 21. 10 Mg.hm-2) > sloping farmland (1. 68, 1. 35 Mg.hm-2) in small macroaggregates and microaggregates, and abandoned land(4. 32 Mg.hm-2) > orchard(4. 00 Mg.hm-2) > forest(3. 22 Mg.hm-2) > sloping farmland (2.37 Mg.hm-2) in silt + clay, forest and abandoned land were higher than orchard and sloping farmland in other three soil aggregates except silt + clay. It was observed that the level of organic carbon and labile organic carbon were decreased when bringing forest under cultivation to orchard or farmland, and augments on organic carbon and labile organic carbon were found after exchanging farmland to abandoned land. The most reverses of forest and abandoned land emerged in small macroaggregates, orchard and sloping farmland were in microaggregates. That was, during the transformations of land utilization pattern, soil aggregates with bigger size were

Experimental testing of exchangeable cutting inserts cutting ability

OpenAIRE

Čep, Robert; Janásek, Adam; Čepová, Lenka; Petrů, Jana; Hlavatý, Ivo; Car, Zlatan; Hatala, Michal

2013-01-01

The article deals with experimental testing of the cutting ability of exchangeable cutting inserts. Eleven types of exchangeable cutting inserts from five different manufacturers were tested. The tested cutting inserts were of the same shape and were different especially in material and coating types. The main aim was both to select a suitable test for determination of the cutting ability of exchangeable cutting inserts and to design such testing procedure that could make it possible...

Persistent Associative Plasticity at an Identified Synapse Underlying Classical Conditioning Becomes Labile with Short-Term Homosynaptic Activation.

Science.gov (United States)

Hu, Jiangyuan; Schacher, Samuel

2015-12-09

Synapses express different forms of plasticity that contribute to different forms of memory, and both memory and plasticity can become labile after reactivation. We previously reported that a persistent form of nonassociative long-term facilitation (PNA-LTF) of the sensorimotor synapses in Aplysia californica, a cellular analog of long-term sensitization, became labile with short-term heterosynaptic reactivation and reversed when the reactivation was followed by incubation with the protein synthesis inhibitor rapamycin. Here we examined the reciprocal impact of different forms of short-term plasticity (reactivations) on a persistent form of associative long-term facilitation (PA-LTF), a cellular analog of classical conditioning, which was expressed at Aplysia sensorimotor synapses when a tetanic stimulation of the sensory neurons was paired with a brief application of serotonin on 2 consecutive days. The expression of short-term homosynaptic plasticity [post-tetanic potentiation or homosynaptic depression (HSD)], or short-term heterosynaptic plasticity [serotonin-induced facilitation or neuropeptide Phe-Met-Arg-Phe-NH2 (FMRFa)-induced depression], at synapses expressing PA-LTF did not affect the maintenance of PA-LTF. The kinetics of HSD was attenuated at synapses expressing PA-LTF, which required activation of protein kinase C (PKC). Both PA-LTF and the attenuated kinetics of HSD were reversed by either a transient blockade of PKC activity or a homosynaptic, but not heterosynaptic, reactivation when paired with rapamycin. These results indicate that two different forms of persistent synaptic plasticity, PA-LTF and PNA-LTF, expressed at the same synapse become labile when reactivated by different stimuli. Activity-dependent changes in neural circuits mediate long-term memories. Some forms of long-term memories become labile and can be reversed with specific types of reactivations, but the mechanism is complex. At the cellular level, reactivations that induce a

Determination of cut front position in laser cutting

International Nuclear Information System (INIS)

Pereira, M; Thombansen, U

2016-01-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable. (paper)

Dust loadings on some common plants near Lucknow city. [Acacia melanoxylon, Bauhinia malabarica, Bougain-villea glabra, Calotropis procera, Catharanthus roseus, Eucalyptus globulus, Ipomoea fistulosa and Peltophorum pterocarpum

Energy Technology Data Exchange (ETDEWEB)

Yunus, M.; Dwivedi, A.K.; Kulshreshtha, K.; Ahmad, K.J.

1985-01-01

Eight plant species - Acacia melanoxylon, Bauhinia malabarica, Bougain-villea glabra, Calotropis procera, Catharanthus roseus, Eucalyptus globulus, Ipomoea fistulosa and Peltophorum pterocarpum - were collected from a newly established suburb colony of Lucknow city, where the major pollutant is dust, to study the dust cleansing efficiency of the plant canopy and also to establish the correlation between the leaf morphological characteristics and their dust trapping potential. The dust load, in milligrams per square centimeter of leaf surface, was measured and related to foliar epidermal and cuticular characteristics, and morphological features.

Antifungal and antimycotoxigenic activity of essential oils from Eucalyptus globulus, Thymus capitatus and Schinus molle

Directory of Open Access Journals (Sweden)

Ana Karenth LÓPEZ-MENESES

2015-12-01

Full Text Available Abstract Essential oils (EO of eucalyptus (Eucalyptus globulus L., thymus (Thymus capitatus L. pirul (Schinus molle L. were evaluated for their efficacy to control Aspergillus parasiticus and Fusarium moniliforme growth and their ability to produce mycotoxins. Data from kinetics radial growth was used to obtain the half maximal inhibitory concentration (IC50. The IC50 was used to evaluate spore germination kinetic and mycotoxin production. Also, spore viability was evaluated by the MTT assay. All EO had an effect on the radial growth of both species. After 96 h of incubation, thymus EO at concentrations of 1000 and 2500 µL L–1 totally inhibited the growth of F. moniliforme and A. parasiticus, respectively. Eucalyptus and thymus EO significantly reduced spore germination of A. parasiticus. Inhibition of spore germination of F. moniliforme was 84.6, 34.0, and 30.6% when exposed to eucalyptus, pirul, and thymus EO, respectively. Thymus and eucalyptus EO reduced aflatoxin (4% and fumonisin (31% production, respectively. Spore viability was affected when oils concentration increased, being the thymus EO the one that reduced proliferation of both fungi. Our findings suggest that EO affect F. moniliforme and A. parasiticus development and mycotoxin production.

[Ovicidal and larvicidal activity in vitro of Eucalyptus globulus essential oils on Haemonchus contortus].

Science.gov (United States)

Macedo, Iara T F; Bevilaqua, Claudia M L; de Oliveira, Lorena M B; Camurça-Vasconcelos, Ana L F; Vieira, Luiz da S; Oliveira, Fabrício R; Queiroz-Junior, Eudson M; Portela, Bruno G; Barros, Renata S; Chagas, Ana C S

2009-01-01

The objective of this work was to evaluate ovicidal and larvicidal effects of Eucalyptus globulus essential oil (EGEO) on Haemonchus contortus. The chemical composition determination of EGEO was through gas chromatography and mass spectrometry. Egg hatch test (EHT) was performed in concentrations 21.75; 17.4; 8.7; 5.43 e 2.71 mg x mL(-1). In larval development test (LDT) were used the concentrations 43.5; 21.75; 10.87; 5.43 e 2.71 mg x mL(-1). Each trial was conducted by negative control with Tween 80 (3%) and positive control, 0.02 mg x mL(-1) of thiabendazole in EHT and 0.008 mg x mL(-1) of ivermectin in LDT. The maximum effectiveness of EGEO on eggs was 99.3% in concentration of 21.75 mg x mL(-1) and on larvae was 98.7% in concentration 43.5 mg x mL(-1). The concentration of EGEO that inhibits 50% of the eggs and larvae was 8.3 and 6.92 mg x mL(-1), respectively. The oil chemical analysis identified as main component the monoterpen 1,8-cineol. EGEO presented ovicidal and larvicidal activities in vitro, revealing a good potential for use in the control of sheep and goat gastrointestinal nematodes.

Nickel-tolerant ectomycorrhizal Pisolithus albus ultramafic ecotype isolated from nickel mines in New Caledonia strongly enhance growth of the host plant Eucalyptus globulus at toxic nickel concentrations.

Science.gov (United States)

Jourand, Philippe; Ducousso, Marc; Reid, Robert; Majorel, Clarisse; Richert, Clément; Riss, Jennifer; Lebrun, Michel

2010-10-01

Ectomycorrhizal (ECM) Pisolithus albus (Cooke & Massee), belonging to the ultramafic ecotype isolated in nickel-rich serpentine soils from New Caledonia (a tropical hotspot of biodiversity) and showing in vitro adaptive nickel tolerance, were inoculated to Eucalyptus globulus Labill used as a Myrtaceae plant-host model to study ectomycorrhizal symbiosis. Plants were then exposed to a nickel (Ni) dose-response experiment with increased Ni treatments up to 60 mg kg( - )(1) soil as extractable Ni content in serpentine soils. Results showed that plants inoculated with ultramafic ECM P. albus were able to tolerate high and toxic concentrations of Ni (up to 60 μg g( - )(1)) while uninoculated controls were not. At the highest Ni concentration tested, root growth was more than 20-fold higher and shoot growth more than 30-fold higher in ECM plants compared with control plants. The improved growth in ECM plants was associated with a 2.4-fold reduction in root Ni concentration but a massive 60-fold reduction in transfer of Ni from root to shoots. In vitro, P. albus strains could withstand high Ni concentrations but accumulated very little Ni in its tissue. The lower Ni uptake by mycorrhizal plants could not be explained by increased release of metal-complexing chelates since these were 5- to 12-fold lower in mycorrhizal plants at high Ni concentrations. It is proposed that the fungal sheath covering the plant roots acts as an effective barrier to limit transfer of Ni from soil into the root tissue. The degree of tolerance conferred by the ultramafic P. albus isolates to growth of the host tree species is considerably greater than previously reported for other ECM. The primary mechanisms underlying this improved growth were identified as reduced Ni uptake into the roots and markedly reduced transfer from root to shoot in mycorrhizal plants. The fact that these positive responses were observed at Ni concentrations commonly observed in serpentinic soils suggests that

Relationship between the lability of sediment-bound Cd and its bioaccumulation in edible oyster.

Science.gov (United States)

Chakraborty, Parthasarathi; Ramteke, Darwin; Chakraborty, Sucharita; Chennuri, Kartheek; Bardhan, Pratirupa

2015-11-15

A linkage between Cd speciation in sediments and its bioaccumulation in edible oyster (Crassostrea sp.) from a tropical estuarine system was established. Bioaccumulation of Cd in edible oyster increased with the increasing lability and dissociation rate constants of Cd-sediment complexes in the bottom sediments. Total Cd concentration in sediment was not a good indicator of Cd-bioavailability. Increasing trace metal competition in sediments increased lability and bioavailability of Cd in the tropical estuarine sediment. Low thermodynamic stability and high bioavailability of Cd in the estuarine sediment were responsible for high bioaccumulation of Cd in edible oysters (3.2-12.2mgkg(-1)) even though the total concentration of Cd in the bottom sediment was low (0.17-0.49mgkg(-1)). Copyright © 2015 Elsevier Ltd. All rights reserved.

Core Cutting Test with Vertical Rock Cutting Rig (VRCR)

Science.gov (United States)

Yasar, Serdar; Osman Yilmaz, Ali

2017-12-01

Roadheaders are frequently used machines in mining and tunnelling, and performance prediction of roadheaders is important for project economics and stability. Several methods were proposed so far for this purpose and, rock cutting tests are the best choice. Rock cutting tests are generally divided into two groups which are namely, full scale rock cutting tests and small scale rock cutting tests. These two tests have some superiorities and deficiencies over themselves. However, in many cases, where rock sampling becomes problematic, small scale rock cutting test (core cutting test) is preferred for performance prediction, since small block samples and core samples can be conducted to rock cutting testing. Common problem for rock cutting tests are that they can be found in very limited research centres. In this study, a new mobile rock cutting testing equipment, vertical rock cutting rig (VRCR) was introduced. Standard testing procedure was conducted on seven rock samples which were the part of a former study on cutting rocks with another small scale rock cutting test. Results showed that core cutting test can be realized successfully with VRCR with the validation of paired samples t-test.

Characteristics of labile organic carbon fractions in reclaimed mine soils: Evidence from three reclaimed forests in the Pingshuo opencast coal mine, China.

Science.gov (United States)

Yuan, Ye; Zhao, Zhongqiu; Li, Xuezhen; Wang, Yangyang; Bai, Zhongke

2018-02-01

The reclamation of discarded spoils has the potential to stimulate carbon (C) sequestration in reclaimed mine soils (RMSs). Nevertheless, to date the temporal dynamics of labile organic C fractions have not been sufficiently elucidated in RMSs. In this study, soil organic carbon (SOC) and labile organic C fractions, including microbial biomass organic C (MBC), easily oxidizable organic C (EOC) and dissolved organic C (DOC), were determined in Robinia pseudoacacia monoculture forests (reclamation periods of 0, 8, 10, 13, 15, 18 and 30years), Pinus tabuliformis forests (reclamation periods of 0, 10, 19, 23 and 25years) and Ulmus pumila forests (reclamation periods of 0, 18, 20 and 22years) situated on RMSs in the Pingshuo opencast coal mine, China. Changes in labile organic C fractions within the soil profiles (0-100cm) were also identified at the 18- or 19-year plots under the three monoculture forests. Our results showed that, SOC and labile organic C fractions, together with soil microbial quotient (SMQ) and C management index (CMI), increased with time since reclamation, indicating that the quality of RMSs improved over time after initial reclamation under the three forest types. R. pseudoacacia significantly increased the accretion of SOC and EOC in the early stage of reclamation while P. tabuliformis accelerated the accumulation of the MBC fraction. Results for U. pumila indicated that this species had a better ability to store C in RMSs 10years or more after reclamation. SOC and labile organic C fractions both had S-shaped distributions within the soil profiles (0-100cm), with the 0-20cm layer recording the highest values (Pfractions were closely associated and correlated with soil physicochemical properties; our results also showed that nitrogen played an important role in the development of labile organic C fractions. Overall, reclamation accelerated the accretion of both SOC and labile organic C fractions, results of which varied among the reclaimed forests

Improved cutting performance in high power laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

2003-01-01

Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

In situ high-resolution evaluation of labile arsenic and mercury in sediment of a large shallow lake

International Nuclear Information System (INIS)

Wang, Chao; Yao, Yu; Wang, Peifang; Hou, Jun; Qian, Jin; Yuan, Ye; Fan, Xiulei

2016-01-01

The precise evaluation of arsenic (As) and mercury (Hg) bioavailability in sediment is crucial to controlling As and Hg contamination, but traditional ex situ measurements hamper comprehensive analysis of labile As and Hg in sediment. In this study, we characterized in situ labile As and Hg in sediment of Lake Hongze using the zirconium (Zr) oxide diffusive gradients in thin films (DGT) technique and 3-mercaptopropyl functionalized silica gel DGT, respectively. The concentrations of DGT-labile As and Hg in the sediment profiles were found to exhibit considerable variation, ranging from 0.15 to 4.15 μg L −1 for As and from 0.04 to 1.35 μg L −1 for Hg. As and Hg flux values, calculated based on the concentration gradients measured from the DGT profiles for both the overlying water and sediment close to the sediment–water interface, were used to determine the contamination status of As and Hg. Flux values of As and Hg were between − 0.066 and 0.067 ng cm −2 d −1 and between − 0.0187 and 0.0181 ng cm −2 d −1 , respectively. The GNU's Not Unix R (GNU R) programming language was used to identify outliers of As and Hg at various depths at the sampling sites. The results indicate that the sites with the most outliers were all located in the regions that were seriously affected by contaminants from the Huai River. The DGT-labile As and Hg concentrations in the 0–30 mm layer were found to be significantly correlated with concentrations of labile As and Hg, total dissolved As and Hg, and total As and Hg in the overlying water, as indicated by ex situ measurements. Results show that DGT is a reliable and high-resolution technique that can be used for in situ monitoring of the labile fractions of As and Hg in sediment in fresh water bodies. - Graphical abstract: The principle of DGT is based on the diffusion of dissolved species through a well-defined gel and subsequent accumulation on an ion-exchange resin. A diffusion gel and a filter membrane (to

Labile pools of Pb in vegetable-growing soils investigated by an isotope dilution method and its influence on soil pH.

Science.gov (United States)

Xie, Hong; Huang, Zhi-Yong; Cao, Ying-Lan; Cai, Chao; Zeng, Xiang-Cheng; Li, Jian

2012-08-01

Pollution of Pb in the surface of agricultural soils is of increasing concern due to its serious impact on the plant growth and the human health through the food chain. However, the mobility, activity and bioavailability of Pb rely mainly on its various chemical species in soils. In the present study, E and L values, the labile pools of isotopically exchangeable Pb, were estimated using the method of isotope dilution in three vegetable-growing soils. The experiments involved adding a stable enriched isotope ((206)Pb > 96%) to a soil suspension and to soils in which plants are subsequently grown, the labile pools of Pb were then estimated by measuring the isotopic composition of Pb in soil solutions and in the plant tissues, respectively. In addition, the correlation of E values and soil pH was investigated at the ranges of pH 4.5-7.0. The amount of labile Pb in soils was also estimated using different single chemical extractants and a modified BCR approach. The results showed that after spiking the enriched isotopes of (206)Pb (>96%) for 24 hours an equilibration of isotopic exchanges in soil suspensions was achieved, and the isotope ratios of (208)Pb/(206)Pb measured at that time was used for calculating the E(24 h) values. The labile pools of Pb by %E(24 h) values, ranging from 53.2% to 61.7% with an average 57%, were found to be significantly higher (p soil pH was found in the tested soil sample. The results indicate that the %E(24 h) value can more rapidly and easily predict the labile pools of Pb in soils compared with L values, but it might be readily overestimated because of the artificial soil acidity derived from the spiked isotopic tracer and the excess of spiked enriched isotopes. The results also suggest that the amounts of Pb extracted with EDTA and the Σ(BCR) values extracted with the modified BCR approach are helpful to detect the labile pools of Pb in soils. In addition, the negative correlation between soil pH and the labile pools of Pb in soils

Heat-Labile Enterotoxin: Beyond G M1 Binding

Directory of Open Access Journals (Sweden)

Benjamin Mudrak

2010-06-01

Full Text Available Enterotoxigenic Escherichia coli (ETEC is a significant source of morbidity and mortality worldwide. One major virulence factor released by ETEC is the heat-labile enterotoxin LT, which is structurally and functionally similar to cholera toxin. LT consists of five B subunits carrying a single catalytically active A subunit. LTB binds the monosialoganglioside GM1, the toxin’s host receptor, but interactions with A-type blood sugars and E. coli lipopolysaccharide have also been identified within the past decade. Here, we review the regulation, assembly, and binding properties of the LT B-subunit pentamer and discuss the possible roles of its numerous molecular interactions.

The evolution of dioecy, heterodichogamy, and labile sex expression in Acer.

Science.gov (United States)

Renner, S S; Beenken, L; Grimm, G W; Kocyan, A; Ricklefs, R E

2007-11-01

The northern hemisphere tree genus Acer comprises 124 species, most of them monoecious, but 13 dioecious. The monoecious species flower dichogamously, duodichogamously (male, female, male), or in some species heterodichogamously (two morphs that each produce male and female flowers but at reciprocal times). Dioecious species cannot engage in these temporal strategies. Using a phylogeny for 66 species and subspecies obtained from 6600 nucleotides of chloroplast introns, spacers, and a protein-coding gene, we address the hypothesis (Pannell and Verdú, Evolution 60: 660-673. 2006) that dioecy evolved from heterodichogamy. This hypothesis was based on phylogenetic analyses (Gleiser and Verdú, New Phytol. 165: 633-640. 2005) that included 29-39 species of Acer coded for five sexual strategies (duodichogamous monoecy, heterodichogamous androdioecy, heterodichogamous trioecy, dichogamous subdioecy, and dioecy) treated as ordered states or as a single continuous variable. When reviewing the basis for these scorings, we found errors that together with the small taxon sample, cast doubt on the earlier inferences. Based on published studies, we coded 56 species of Acer for four sexual strategies, dioecy, monoecy with dichogamous or duodichogamous flowering, monoecy with heterodichogamous flowering, or labile sex expression, in which individuals reverse their sex allocation depending on environment-phenotype interactions. Using Bayesian character mapping, we infer an average of 15 transformations, a third of them involving changes from monoecy-cum-duodichogamy to dioecy; less frequent were changes from this strategy to heterodichogamy; dioecy rarely reverts to other sexual systems. Contra the earlier inferences, we found no switches between heterodichogamy and dioecy. Unexpectedly, most of the species with labile sex expression are grouped together, suggesting that phenotypic plasticity in Acer may be a heritable sexual strategy. Because of the complex flowering phenologies

Twice cutting method reduces tibial cutting error in unicompartmental knee arthroplasty.

Science.gov (United States)

Inui, Hiroshi; Taketomi, Shuji; Yamagami, Ryota; Sanada, Takaki; Tanaka, Sakae

2016-01-01

Bone cutting error can be one of the causes of malalignment in unicompartmental knee arthroplasty (UKA). The amount of cutting error in total knee arthroplasty has been reported. However, none have investigated cutting error in UKA. The purpose of this study was to reveal the amount of cutting error in UKA when open cutting guide was used and clarify whether cutting the tibia horizontally twice using the same cutting guide reduced the cutting errors in UKA. We measured the alignment of the tibial cutting guides, the first-cut cutting surfaces and the second cut cutting surfaces using the navigation system in 50 UKAs. Cutting error was defined as the angular difference between the cutting guide and cutting surface. The mean absolute first-cut cutting error was 1.9° (1.1° varus) in the coronal plane and 1.1° (0.6° anterior slope) in the sagittal plane, whereas the mean absolute second-cut cutting error was 1.1° (0.6° varus) in the coronal plane and 1.1° (0.4° anterior slope) in the sagittal plane. Cutting the tibia horizontally twice reduced the cutting errors in the coronal plane significantly (Pcutting the tibia horizontally twice using the same cutting guide reduced cutting error in the coronal plane. Copyright © 2014 Elsevier B.V. All rights reserved.

Labile synthetic cadmium complexes are not bioavailable to Pseudokirchneriella subcapitata in resin buffered solutions

Energy Technology Data Exchange (ETDEWEB)

Verheyen, L., E-mail: Liesbeth.Verheyen@ees.kuleuven.be [Division of Soil and Water Management, K.U. Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium); Merckx, R. [Division of Soil and Water Management, K.U.Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium); Smolders, E., E-mail: Erik.Smolders@ees.kuleuven.be [Division of Soil and Water Management, K.U. Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium)

2012-11-15

The Free Ion Activity Model (FIAM) predicts that cadmium (Cd) uptake by organisms is identical for solutions with the same free Cd{sup 2+} concentration and inorganic composition. Clear exceptions to the FIAM have been shown for Cd uptake by plant roots, periphyton and human cells where labile Cd complexes increase bioavailability and which has been attributed to their role in enhancing Cd diffusion towards the uptake cells. Here, we assessed the role of labile Cd complexes on Cd uptake by algae, for which diffusion limitations should be less pronounced due to their smaller size. Long-term (3 days) Cd uptake by the green algae Pseudokirchneriella subcapitata was measured in resin buffered solutions with or without synthetic ligands and at three Cd{sup 2+} ion activities (pCd 8.2-5.7). The free Cd{sup 2+} activity was maintained during the test using a metal-selective resin located in the algal bottles. Total dissolved Cd increased up to 35-fold by adding the synthetic ligands at constant Cd{sup 2+} activity. In contrast, Cd uptake by algae increased maximally 2.8 fold with increasing concentration of the synthetic ligands and the availability of the complexes were maximally 5.2% relative to Cd{sup 2+} for NTA and CDTA complexes. It is concluded that labile Cd complexes do not greatly enhance Cd bioavailability to the unicellular algae and calculations suggest that Cd transport from solution to these small cells is not rate limiting.

Labile synthetic cadmium complexes are not bioavailable to Pseudokirchneriella subcapitata in resin buffered solutions

International Nuclear Information System (INIS)

Verheyen, L.; Merckx, R.; Smolders, E.

2012-01-01

The Free Ion Activity Model (FIAM) predicts that cadmium (Cd) uptake by organisms is identical for solutions with the same free Cd 2+ concentration and inorganic composition. Clear exceptions to the FIAM have been shown for Cd uptake by plant roots, periphyton and human cells where labile Cd complexes increase bioavailability and which has been attributed to their role in enhancing Cd diffusion towards the uptake cells. Here, we assessed the role of labile Cd complexes on Cd uptake by algae, for which diffusion limitations should be less pronounced due to their smaller size. Long-term (3 days) Cd uptake by the green algae Pseudokirchneriella subcapitata was measured in resin buffered solutions with or without synthetic ligands and at three Cd 2+ ion activities (pCd 8.2–5.7). The free Cd 2+ activity was maintained during the test using a metal-selective resin located in the algal bottles. Total dissolved Cd increased up to 35-fold by adding the synthetic ligands at constant Cd 2+ activity. In contrast, Cd uptake by algae increased maximally 2.8 fold with increasing concentration of the synthetic ligands and the availability of the complexes were maximally 5.2% relative to Cd 2+ for NTA and CDTA complexes. It is concluded that labile Cd complexes do not greatly enhance Cd bioavailability to the unicellular algae and calculations suggest that Cd transport from solution to these small cells is not rate limiting.

Assessing soil constituents and labile soil organic carbon by mid-infrared photoacoustic spectroscopy

DEFF Research Database (Denmark)

Peltre, Clément; Bruun, Sander; Du, Changwen

2014-01-01

) degradability. The objective of this study was to assess the potential of FTIR-PAS for the characterisation of the labile fraction of SOC and more classical soil parameters, such as carbon and clay content, for a range of 36 soils collected from various field experiments in Denmark. Partial least squares (PLS...... signal. This also means that it should be advantageous for soil analysis because of its highly opaque nature. However, only a limited number of studies have so far applied FTIR-PAS to soil characterization and investigation is still required into its potential to determine soil organic carbon (SOC......) regression was used to correlate the collected FTIR-PAS spectra with the proportion of soil organic carbon mineralised after 238 days of incubation at 15°C and pF 2 (C238d) taken as an indicator of the labile fraction of SOC. Results showed that it is possible to predict total organic carbon content, total...

Hemorrhagic Shock and Surgical Stress Alter Distribution of Labile Zinc within High and Low Molecular Weight Plasma Fractions

Science.gov (United States)

Kelly, Edward; Mathew, Jeff; Kohler, Jonathan E.; Blass, Amy L.; Soybel, David I.

2012-01-01

Zinc ions (Zn2+) are essential for tissue repair following injury or stress. We hypothesize that during such stresses Zn2+ is redistributed to labile pools in plasma components. Here we tested this hypothesis utilizing a novel assay to monitor labile Zn2+ in plasma in hemorrhagic shock. Adult rats in the Shock (S) group underwent hemorrhage and resuscitation. Blood samples were drawn at baseline, 1 hr, 4 hrs and 24 hrs. The Surgical Control (SC) group was anesthetized and instrumented, but not bled. Albumin, total Zn2+, and labile Zn2+ levels were assayed in plasma. Binding capacity for Zn2+ was assessed in high (HMW) and low (LMW) molecular weight pools. Significant decreases in total Zn2+ were observed by 24 hrs, in both S and SC groups. Albumin levels were significantly reduced in the S group at 1 hr and 4 hr but restored at 24 hrs; significant changes were not observed in other groups. In whole plasma, labile Zn2+ levels were stable initially in the S and SC groups, but declined at 24 hrs. In the HMW pool, marked and significant impairment of binding was noted throughout all time periods following the shock period in the S group. Such changes were observed in the SC group of less intensity and duration. These experiments suggest that Shock alters affinity of plasma proteins for Zn2+, promoting delivery to peripheral tissues during periods of increased Zn2+ utilization. PMID:22744307

Hemorrhagic shock and surgical stress alter distribution of labile zinc within high- and low-molecular-weight plasma fractions.

Science.gov (United States)

Kelly, Edward; Mathew, Jeff; Kohler, Jonathan E; Blass, Amy L; Soybel, And David I

2012-08-01

Zinc ions (Zn) are essential for tissue repair following injury or stress. We hypothesize that during such stresses Zn is redistributed to labile pools in plasma components. Here we tested this hypothesis using a novel assay to monitor labile Zn in plasma in hemorrhagic shock. Adult rats in the shock group (S group) underwent hemorrhage and resuscitation. Blood samples were drawn at baseline and at 1, 4, and 24 h. The surgical control group (SC group) was anesthetized and instrumented, but not bled. Albumin, total Zn, and labile Zn levels were assayed in plasma. Binding capacity for Zn was assessed in high- and low-molecular-weight pools. Significant decreases in total Zn were observed by 24 h, in both S and SC groups. Albumin levels were significantly reduced in the S group at 1 and 4 h but restored at 24 h; significant changes were not observed in other groups. In whole plasma, labile Zn levels were stable initially in the S and SC groups, but declined at 24 h. In the high-molecular-weight pool, marked and significant impairment of binding was noted throughout all time periods following the shock period in the S group. Such changes were observed in the SC group of less intensity and duration. These experiments suggest that shock alters affinity of plasma proteins for Zn, promoting delivery to peripheral tissues during periods of increased Zn utilization.

Preparation and evaluation of oral multiparticulate formulations of acid-labile drugs

OpenAIRE

Huang, Fang

2017-01-01

Säure-labile Medikamente werden leicht in saurem Medium abgebaut, welche hauptsächlich als enterisch beschichtete Dosierungsformen für die orale Verabreichung formuliert wurden. Das Ziel dieser Studie war es, orale multipartikuläre Formulierungen von säure-labilen Medikamenten, mit Ilaprazol, Lansoprazol und Rabeprazol Natrium als Modellarzneistoffe vorzubereiten. Der Einfluss der Wirkstofflöslichkeit von Lansoprazol und Rabeprazol Natrium und des Kerntyps, wurde auf das Übe...

Deposição de serapilheira e nutrientes em plantio de Eucalyptus urophylla × E. globulus

Directory of Open Access Journals (Sweden)

Márcio Viera

Full Text Available Objetivou-se com o presente estudo avaliar a deposição de serapilheira e nutrientes em plantio de Eucalyptus urophylla × Eucalyptus globulus, em Eldorado do Sul-RS. Foram alocadas sistematicamente quatro parcelas de 20 m × 20 m, cada uma com quatro coletores de serapilheira de 1 m². A serapilheira foi coletada quinzenalmente, entre janeiro/2007 e dezembro/2010. A produção de serapilheira foi crescente, com o aumento da idade do povoamento, sendo 6,9 Mg ha-1 aos seis e 8,5 Mg ha-1 aos nove anos. A fração folhas correspondeu, em média, a 66,9% da serapilheira total, seguida pelos galhos finos (14,7%, miscelânea (10,5% e galhos grossos (7,9%. A deposição apresentou padrão sazonal, sendo maior no período de aumento da temperatura do ar. A fração folhas foi responsável por maior parte do retorno de nutrientes via serapilheira, variando de 58,2 a 81,8% da quantidade de Cu e N, respectivamente.

Feasibility of labile Zn phytoextraction using enhanced tobacco and sunflower: results of five- and one-year field-scale experiments in Switzerland.

Science.gov (United States)

Herzig, Rolf; Nehnevajova, Erika; Pfistner, Charlotte; Schwitzguebel, Jean-Paul; Ricci, Arturo; Keller, Charles

2014-01-01

Phytoextraction with somaclonal variants of tobacco and sunflower mutant lines (non-GMs) with enhanced metal uptake and tolerance can be a sustainable alternative to conventional destructive decontamination methods, especially for stripping bioavailable zinc excess in topsoil. The overall results of a 5-year time series experiment at field scale in north-eastern Switzerland confirm that the labile Zn pool in soil can be lowered by 45-70%, whereas subplots without phytoextraction treatment maintained labile Zn concentrations. In 2011, the phytoextraction experiment site was enlarged by a factor of 3, and the labile 0.1 M NaNO3 extractable Zn concentration in the soil was reduced up to 58% one period after harvest. A Mass Balance Analysis confirmed soil Zn decontamination in line with plant Zn uptake. The plants partially take Zn from the non-labile pool of the totaL The sustainability of Zn phytoextraction in subplots that no longer exceed the Swiss trigger value is now assessed over time. In contrary to the phytoextraction of total soil Zn which needs a long cleaning up time, the bioavailable Zn stripping is feasible within a few years period.

Lability of Secondary Organic Particulate Matter

Energy Technology Data Exchange (ETDEWEB)

Liu, Pengfei; Li, Yong Jie; Wang, Yan; Giles, Mary K.; Zaveri, Rahul A.; Bertram, Allan K.; Martin, Scot T.

2016-10-24

Accurate simulations of the consenctrations of atmospheric organic particulate matter (PM) are needed for predicting energy flow in the Earth’s climate system. In the past, simulations of organic PM widely assume equilibrium partitioning of semivolatile organic compounds (SVOCs) between the PM and surrounding vapor. Herein, we test this assumption by measuring evaporation rates and associated vapor mass concentration of organic films representative of atmospheric PM. For films representing anthropogenic PM, evaporation rates and vapor mass concentrations increased above a threshold relative humidity (RH), indicating equilibrium partitioning above a transition RH but not below. In contrast for films representing biogenic PM, no threshold was observed, indicating equilibrium partitioning at all RHs. The results suggest that the mass lability of atmospheric organic PM can differ in consequential ways among Earth’s natural biomes, polluted regions, and regions of land-use change, and these differences need to be considered when simulating atmospheric organic PM.

Second international round robin for the quantification of serum non-transferrin-bound iron and labile plasma iron in patients with iron-overload disorders

NARCIS (Netherlands)

de Swart, Louise; Hendriks, Jan C. M.; van der Vorm, Lisa N.; Cabantchik, Z. Ioav; Evans, Patricia J.; Hod, Eldad A.; Brittenham, Gary M.; Furman, Yael; Wojczyk, Boguslaw; Janssen, Mirian C. H.; Porter, John B.; Mattijssen, Vera E. J. M.; Biemond, Bart J.; MacKenzie, Marius A.; Origa, Raffaella; Galanello, Renzo; Hider, Robert C.; Swinkels, Dorine W.

2016-01-01

Non-transferrin-bound iron and its labile (redox active) plasma iron component are thought to be potentially toxic forms of iron originally identified in the serum of patients with iron overload. We compared ten worldwide leading assays (6 for non-transferrin-bound iron and 4 for labile plasma iron)

In situ high-resolution evaluation of labile arsenic and mercury in sediment of a large shallow lake

Energy Technology Data Exchange (ETDEWEB)

Wang, Chao; Yao, Yu; Wang, Peifang; Hou, Jun; Qian, Jin; Yuan, Ye; Fan, Xiulei

2016-01-15

The precise evaluation of arsenic (As) and mercury (Hg) bioavailability in sediment is crucial to controlling As and Hg contamination, but traditional ex situ measurements hamper comprehensive analysis of labile As and Hg in sediment. In this study, we characterized in situ labile As and Hg in sediment of Lake Hongze using the zirconium (Zr) oxide diffusive gradients in thin films (DGT) technique and 3-mercaptopropyl functionalized silica gel DGT, respectively. The concentrations of DGT-labile As and Hg in the sediment profiles were found to exhibit considerable variation, ranging from 0.15 to 4.15 μg L{sup −1} for As and from 0.04 to 1.35 μg L{sup −1} for Hg. As and Hg flux values, calculated based on the concentration gradients measured from the DGT profiles for both the overlying water and sediment close to the sediment–water interface, were used to determine the contamination status of As and Hg. Flux values of As and Hg were between − 0.066 and 0.067 ng cm{sup −2} d{sup −1} and between − 0.0187 and 0.0181 ng cm{sup −2} d{sup −1}, respectively. The GNU's Not Unix R (GNU R) programming language was used to identify outliers of As and Hg at various depths at the sampling sites. The results indicate that the sites with the most outliers were all located in the regions that were seriously affected by contaminants from the Huai River. The DGT-labile As and Hg concentrations in the 0–30 mm layer were found to be significantly correlated with concentrations of labile As and Hg, total dissolved As and Hg, and total As and Hg in the overlying water, as indicated by ex situ measurements. Results show that DGT is a reliable and high-resolution technique that can be used for in situ monitoring of the labile fractions of As and Hg in sediment in fresh water bodies. - Graphical abstract: The principle of DGT is based on the diffusion of dissolved species through a well-defined gel and subsequent accumulation on an ion-exchange resin. A diffusion

Assessing SOC labile fractions through respiration test, density-size fractionation and thermal analysis - A comparison of methods

Science.gov (United States)

Soucemarianadin, Laure; Cécillon, Lauric; Chenu, Claire; Baudin, François; Nicolas, Manuel; Savignac, Florence; Barré, Pierre

2017-04-01

Soil organic matter (SOM) is the biggest terrestrial carbon reservoir, storing 3 to 4 times more carbon than the atmosphere. However, despite its major importance for climate regulation SOM dynamics remains insufficiently understood. For instance, there is still no widely accepted method to assess SOM lability. Soil respiration tests and particulate organic matter (POM) obtained by different fractionation schemes have been used for decades and are now considered as classical estimates of very labile and labile soil organic carbon (SOC), respectively. But the pertinence of these methods to characterize SOM turnover can be questioned. Moreover, they are very time-consuming and their reproducibility might be an issue. Alternate ways of determining the labile SOC component are thus well-needed. Thermal analyses have been used to characterize SOM among which Rock-Eval 6 (RE6) analysis of soil has shown promising results in the determination of SOM biogeochemical stability (Gregorich et al., 2015; Barré et al., 2016). Using a large set of samples of French forest soils representing contrasted pedoclimatic conditions, including deep samples (up to 1 m depth), we compared different techniques used for SOM lability assessment. We explored whether results from soil respiration test (10-week laboratory incubations), SOM size-density fractionation and RE6 thermal analysis were comparable and how they were correlated. A set of 222 (respiration test and RE6), 103 (SOM fractionation and RE6) and 93 (respiration test, SOM fractionation and RE6) forest soils samples were respectively analyzed and compared. The comparison of the three methods (n = 93) using a principal component analysis separated samples from the surface (0-10 cm) and deep (40-80 cm) layers, highlighting a clear effect of depth on the short-term persistence of SOC. A correlation analysis demonstrated that, for these samples, the two classical methods of labile SOC determination (respiration and SOM fractionation

Suppression of inflammation in a mouse model of rheumatoid arthritis using targeted lipase-labile fumagillin prodrug nanoparticles.

Science.gov (United States)

Zhou, Hui-Fang; Yan, Huimin; Senpan, Angana; Wickline, Samuel A; Pan, Dipanjan; Lanza, Gregory M; Pham, Christine T N

2012-11-01

Nanoparticle-based therapeutics are emerging technologies that have the potential to greatly impact the treatment of many human diseases. However, drug instability and premature release from the nanoparticles during circulation currently preclude clinical translation. Herein, we use a lipase-labile (Sn 2) fumagillin prodrug platform coupled with a unique lipid surface-to-surface targeted delivery mechanism, termed contact-facilitated drug delivery, to counter the premature drug release and overcome the inherent photo-instability of fumagillin, an established anti-angiogenic agent. We show that α(v)β(3)-integrin targeted fumagillin prodrug nanoparticles, administered at 0.3 mg of fumagillin prodrug/kg of body weight suppress the clinical disease indices of KRN serum-mediated arthritis in a dose-dependent manner when compared to treatment with the control nanoparticles with no drug. This study demonstrates the effectiveness of this lipase-labile prodrug nanocarrier in a relevant preclinical model that approximates human rheumatoid arthritis. The lipase-labile prodrug paradigm offers a translatable approach that is broadly applicable to many targeted nanosystems and increases the translational potential of this platform for many diseases. Copyright © 2012 Elsevier Ltd. All rights reserved.

Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

Science.gov (United States)

Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

2017-01-01

In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

Evidence for the involvement of a labile protein in stimulation of adrenal steroidogenesis under conditions not inhibitory to protein synthesis

International Nuclear Information System (INIS)

Krueger, R.J.; Orme-Johnson, N.R.

1988-01-01

Evidence is presented to support the hypothesis that synthesis of a labile protein is required for stimulation of steroidogenesis in rat adrenocortical cells. Amino acids L-canavanine and L-S-aminoethylcysteine, at concentrations as high as 5 mM, each inhibited steroidogenesis to a much greater extent than they inhibited protein synthesis. S-Aminoethylcysteine caused a 50% decrease in the stimulated rate of corticosterone production under conditions where incorporation of [35S]methionine into protein was unchanged. Both amino acids block stimulation of steroid synthesis at a step subsequent to the formation of cAMP and before the synthesis of progesterone. The onset of this effect, after the addition of the amino acids, on corticosterone production is quite rapid. These results provide support, that is not dependent on inhibition of protein synthesis, for the hypothesis that a labile protein mediates stimulation of steroidogenesis. Reversal of canavanine and S-aminoethylcysteine inhibition of steroidogenesis by arginine and lysine, respectively, suggests that the inhibitors are functioning as amino acid analogs. S-Aminoethylcysteine inhibits the incorporation of [3H]lysine into protein as well as inhibits steroidogenesis; further, [3H]S-aminoethylcysteine is incorporated into protein that is nonstimulatory. These results suggest that lysine residues play an essential role in the function of the labile protein or that the labile protein contains a large number of lysine residues

Quantum-chemical evaluation of the lability of π-electronic systems in N-benzoyl derivatives of phosphorus and sulfur imines

International Nuclear Information System (INIS)

Egorov, Yu.P.; Pen'kovskii, V.V.; Boldeskul, I.E.

1986-01-01

The charges on atoms, the bond indices, their components, and the energies of the highest occupied π orbitals of four N-benzoyl derivatives of phosphorus and sulfur imines have been calculated by the CNDO/2 method in an spd basis. According to the results obtained, the π system of a bridging sulfur-nitrogen group is more labile than a phosphorus-nitrogen group, in agreement with the experimental evaluations of the transmission of the electronic effects of substituents in these systems. An interpretation of this lability has been given

Cutting state identification

International Nuclear Information System (INIS)

Berger, B.S.; Minis, I.; Rokni, M.

1997-01-01

Cutting states associated with the orthogonal cutting of stiff cylinders are identified through an analysis of the singular values of a Toeplitz matrix of third order cumulants of acceleration measurements. The ratio of the two pairs of largest singular values is shown to differentiate between light cutting, medium cutting, pre-chatter and chatter states. Sequences of cutting experiments were performed in which either depth of cut or turning frequency was varied. Two sequences of experiments with variable turning frequency and five with variable depth of cut, 42 cutting experiments in all, provided a database for the calculation of third order cumulants. Ratios of singular values of cumulant matrices find application in the analysis of control of orthogonal cutting

Fraction of organic carbon predicts labile desorption rates of chlorinated organic pollutants in laboratory-spiked geosorbents.

Science.gov (United States)

Ginsbach, Jake W; Killops, Kato L; Olsen, Robert M; Peterson, Brittney; Dunnivant, Frank M

2010-05-01

The resuspension of large volumes of sediments that are contaminated with chlorinated pollutants continues to threaten environmental quality and human health. Whereas kinetic models are more accurate for estimating the environmental impact of these events, their widespread use is substantially hampered by the need for costly, time-consuming, site-specific kinetics experiments. The present study investigated the development of a predictive model for desorption rates from easily measurable sorbent and pollutant properties by examining the relationship between the fraction of organic carbon (fOC) and labile release rates. Duplicate desorption measurements were performed on 46 unique combinations of pollutants and sorbents with fOC values ranging from 0.001 to 0.150. Labile desorption rate constants indicate that release rates predominantly depend upon the fOC in the geosorbent. Previous theoretical models, such as the macro-mesopore and organic matter (MOM) diffusion model, have predicted such a relationship but could not accurately predict the experimental rate constants collected in the present study. An empirical model was successfully developed to correlate the labile desorption rate constant (krap) to the fraction of organic material where log(krap)=0.291-0.785 . log(fOC). These results provide the first experimental evidence that kinetic pollution releases during resuspension events are governed by the fOC content in natural geosorbents. Copyright (c) 2010 SETAC.

Plasma cutting or laser cutting. Plasma setsudan ka laser setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Nakamura, A. (Tanaka Engineering Works Ltd., Saitama (Japan))

1991-05-01

Comparisons and discussions were made on the plasma cutting and laser cutting in sheet steel cutting, referring partly to gas cutting. Historically, the cutting has been developed from gas, plasma, and laser in that order, and currently these three methods are used mixedly. Generally, the plasma cutting is superior in cutting speed, but inferior in cut face quality, and it requires measures of dust collection. Due to high accuracy and quality in cut face, the laser cutting has been practically used for quite some time in the thin sheet industry, but medium to thick sheet cutting had a problem of unavailability of high output laser suitable for these ranges. However, the recent technologies have overcome the problem as a result of development at the authors {prime} company of a 2 kW class laser cutter capable of cutting 19 mm thick sheet. The cutter has been proven being particularly excellent in controllability. Choice of whether plasma or laser would depend upon which priority is to be taken, cost or accuracy. 15 figs., 3 tabs.

Supercritical Fluid Extraction of Eucalyptus globulus Bark—A Promising Approach for Triterpenoid Production

Directory of Open Access Journals (Sweden)

Carlos M. Silva

2012-06-01

Full Text Available Eucalyptus bark contains significant amounts of triterpenoids with demonstrated bioactivity, namely triterpenic acids and their acetyl derivatives (ursolic, betulinic, oleanolic, betulonic, 3-acetylursolic, and 3-acetyloleanolic acids. In this work, the supercritical fluid extraction (SFE of Eucalyptus globulus deciduous bark was carried out with pure and modified carbon dioxide to recover this fraction, and the results were compared with those obtained by Soxhlet extraction with dichloromethane. The effects of pressure (100–200 bar, co-solvent (ethanol content (0, 5 and 8% wt, and multistep operation were studied in order to evaluate the applicability of SFE for their selective and efficient production. The individual extraction curves of the main families of compounds were measured, and the extracts analyzed by GC-MS. Results pointed out the influence of pressure and the important role played by the co-solvent. Ethanol can be used with advantage, since its effect is more important than increasing pressure by several tens of bar. At 160 bar and 40 °C, the introduction of 8% (wt of ethanol greatly improves the yield of triterpenoids more than threefold.

Chemical and structural analysis of Eucalyptus globulus and E. camaldulensis leaf cuticles: a lipidized cell wall region

Directory of Open Access Journals (Sweden)

Paula eGuzmán

2014-09-01

Full Text Available The plant cuticle has traditionally been conceived as an independent hydrophobic layer that covers the external epidermal cell wall. Due to its complexity, the existing relationship between cuticle chemical composition and ultra-structure remains unclear to date. This study aimed to examine the link between chemical composition and structure of isolated, adaxial leaf cuticles of Eucalyptus camaldulensis and E. globulus by the gradual extraction and identification of lipid constituents (cutin and soluble lipids, coupled to spectroscopic and microscopic analyses. The soluble compounds and cutin monomers identified could not be assigned to a concrete internal cuticle ultra-structure. After cutin depolymerization, a cellulose network resembling the cell wall was observed, with different structural patterns in the regions ascribed to the cuticle proper and cuticular layer, respectively. Our results suggest that the current cuticle model should be revised, stressing the presence and major role of cell wall polysaccharides. It is concluded that the cuticle may be interpreted as a modified cell wall region which contains additional lipids. The major heterogeneity of the plant cuticle makes it difficult to establish a direct link between cuticle chemistry and structure with the existing methodologies.

Wedge cutting of mild steel by CO 2 laser and cut-quality assessment in relation to normal cutting

Science.gov (United States)

Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

2008-10-01

In some applications, laser cutting of wedge surfaces cannot be avoided in sheet metal processing and the quality of the end product defines the applicability of the laser-cutting process in such situations. In the present study, CO 2 laser cutting of the wedge surfaces as well as normal surfaces (normal to laser beam axis) is considered and the end product quality is assessed using the international standards for thermal cutting. The cut surfaces are examined by the optical microscopy and geometric features of the cut edges such as out of flatness and dross height are measured from the micrographs. A neural network is introduced to classify the striation patterns of the cut surfaces. It is found that the dross height and out of flatness are influenced significantly by the laser output power, particularly for wedge-cutting situation. Moreover, the cut quality improves at certain value of the laser power intensity.

Non-labile silver species in biosolids remain stable throughout 50 years of weathering and ageing.

Science.gov (United States)

Increasing commercial use of nanosilver has focussed attention on the fate of silver (Ag) in the wastewater release pathway. This paper reports the speciation and lability of Ag in archived, stockpiled, and contemporary biosolids from the UK, USA and Australia, and indicates that...

Acid-Labile Amphiphilic PEO-b-PPO-b-PEO Copolymers: Degradable Poloxamer Analogs.

Science.gov (United States)

Worm, Matthias; Kang, Biao; Dingels, Carsten; Wurm, Frederik R; Frey, Holger

2016-05-01

Poly ((ethylene oxide)-b-(propylene oxide)-b-(ethylene oxide)) triblock copolymers commonly known as poloxamers or Pluronics constitute an important class of nonionic, biocompatible surfactants. Here, a method is reported to incorporate two acid-labile acetal moieties in the backbone of poloxamers to generate acid-cleavable nonionic surfactants. Poly(propylene oxide) is functionalized by means of an acetate-protected vinyl ether to introduce acetal units. Three cleavable PEO-PPO-PEO triblock copolymers (Mn,total = 6600, 8000, 9150 g·mol(-1) ; Mn,PEO = 2200, 3600, 4750 g·mol(-1) ) have been synthesized using anionic ring-opening polymerization. The amphiphilic copolymers exhibit narrow molecular weight distributions (Ð = 1.06-1.08). Surface tension measurements reveal surface-active behavior in aqueous solution comparable to established noncleavable poloxamers. Complete hydrolysis of the labile junctions after acidic treatment is verified by size exclusion chromatography. The block copolymers have been employed as surfactants in a miniemulsion polymerization to generate polystyrene (PS) nanoparticles with mean diameters of ≈200 nm and narrow size distribution, as determined by dynamic light scattering and scanning electron microscopy. Acid-triggered precipitation facilitates removal of surfactant fragments from the nanoparticles, which simplifies purification and enables nanoparticle precipitation "on demand." © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dual, differential isotope labeling shows the preferential movement of labile plant constituents into mineral-bonded soil organic matter.

Science.gov (United States)

Haddix, Michelle L; Paul, Eldor A; Cotrufo, M Francesca

2016-06-01

The formation and stabilization of soil organic matter (SOM) are major concerns in the context of global change for carbon sequestration and soil health. It is presently believed that lignin is not selectively preserved in soil and that chemically labile compounds bonding to minerals comprise a large fraction of the SOM. Labile plant inputs have been suggested to be the main precursor of the mineral-bonded SOM. Litter decomposition and SOM formation are expected to have temperature sensitivity varying with the lability of plant inputs. We tested this framework using dual (13) C and (15) N differentially labeled plant material to distinguish the metabolic and structural components within a single plant material. Big Bluestem (Andropogon gerardii) seedlings were grown in an enriched (13) C and (15) N environment and then prior to harvest, removed from the enriched environment and allowed to incorporate natural abundance (13) C-CO2 and (15) N fertilizer into the metabolic plant components. This enabled us to achieve a greater than one atom % difference in (13) C between the metabolic and structural components within the plant litter. This differentially labeled litter was incubated in soil at 15 and 35 °C, for 386 days with CO2 measured throughout the incubation. After 14, 28, 147, and 386 days of incubation, the soil was subsequently fractionated. There was no difference in temperature sensitivity of the metabolic and structural components with regard to how much was respired or in the amount of litter biomass stabilized. Only the metabolic litter component was found in the sand, silt, or clay fraction while the structural component was exclusively found in the light fraction. These results support the stabilization framework that labile plant components are the main precursor of mineral-associated organic matter. © 2016 John Wiley & Sons Ltd.

Constraints on Transport and Emplacement Mechanisms of Labile Fractions in Lunar Cold Traps

Science.gov (United States)

Rickman, D.; Gertsch, L.

2014-01-01

Sustaining the scientific exploration of the Solar System will require a significant proportion of the necessary fuels and propellants, as well as other bulk commodities, to be produced from local raw materials [1]. The viability of mineral production depends on the ability to locate and characterize mineable deposits of the necessary feedstocks. This requires, among other things, a workable understanding of the mechanisms by which such deposits form, which is the subject of Economic Geology. Multiple deposition scenarios are possible for labile materials on the Moon. This paper suggests labile fractions moved diffusely through space; deposits may grow richer with depth until low porosity rock; lateral transport is likely to have occurred with the regolith, at least for short distances; crystalline ice may not exist; the constituent phases could be extremely complex. At present we can constrain the sources only mildly; once on the Moon, the transport mechanisms inherently mix and therefore obscure the origins. However, the importance of expanding our understanding of ore-forming processes on the Moon behooves us to make the attempt. Thus begins a time of new inquiry for Economic Geology.

Two clusters of GABAergic ellipsoid body neurons modulate olfactory labile memory in Drosophila.

Science.gov (United States)

Zhang, Zhiping; Li, Xiaoting; Guo, Jing; Li, Yan; Guo, Aike

2013-03-20

In Drosophila, aversive olfactory memory is believed to be stored in a prominent brain structure, the mushroom body (MB), and two pairs of MB intrinsic neurons, the dorsal paired medial (DPM) and the anterior paired lateral (APL) neurons, are found to regulate the consolidation of middle-term memory (MTM). Here we report that another prominent brain structure, the ellipsoid body (EB), is also involved in the modulation of olfactory MTM. Activating EB R2/R4m neurons does not affect the learning index, but specifically eliminates anesthesia-sensitive memory (ASM), the labile component of olfactory MTM. We further demonstrate that approximately two-thirds of these EB neurons are GABAergic and are responsible for the suppression of ASM. Using GRASP (GFP reconstitution across synaptic partners), we reveal potential synaptic connections between the EB and MB in regions covering both the presynaptic and postsynaptic sites of EB neurons, suggesting the presence of bidirectional connections between these two important brain structures. These findings suggest the existence of direct connections between the MB and EB, and provide new insights into the neural circuit basis for olfactory labile memory in Drosophila.

Effect of temperature on the decomposition of labile and recalcitrant organic matter in Chernozem

Science.gov (United States)

Larioinova, Alla; Kvitkina, Anna; Bykhovets, Sergey; Stulin, Alexandr; Blagodatskaya, Evgenia

2017-04-01

We tested the hypothesis that the recalcitrant pool of soil organic matter (SOM) is more temperature sensitive to decomposition than the labile one. The hypothesis was verified for Chernozem soil sampled from the control (unfertilized) and fertilized with NPK experimental plots of the 50 year field experiment with maize monoculture in Voronezh Region, Russia (51o41'N, 39o15'E). The labile and recalcitrant SOM pools at 2, 12, and 22°C in a long-term (430 d) incubation experiment were traced using the method of 13C natural abundance by C3-C4 transition. Based on decomposition rate constants, the SOM pools followed the order plant residues < new (C4) SOM < old (C3) SOM, with plant residues as the most labile C pool. The hypothesis was valid only for the temperature interval of 12-22°C, where Q10 values increased in the recalcitrance order from 1.2 (plant residues) to 4.3 (C3 SOM). At low temperatures (2-12°C), the values of Q10 varied in the narrow range of 2.2-2.8 irrespective of a SOM pool. In the soil under maize monoculture fertilized with NPK, the increased decomposition of C3 SOM was observed compared to the unfertilized control. The input of new C4 carbon decreased the rate of CO2 emission during the decomposition of the old C3 SOM, i.e. induced negative priming effect (PE). To the contrast, the fertilization increased the positive PE for the C3 SOM. Along with the SOM decomposition rate constants, the magnitude of PE was also temperature dependent. The maximal negative PE in control treatment was found at the lowest temperature of 2oC, while the highest positive PE in NPK fertilized soil was observed at the highest temperature of 22oC.

PURIFICATION AND CHARACTERIZATION OF AN OXYGEN-LABILE, NAD-DEPENDENT ALCOHOL-DEHYDROGENASE FROM DESULFOVIBRIO-GIGAS

NARCIS (Netherlands)

HENSGENS, CMH; VONCK, J; VANBEEUMEN, J; VANBRUGGEN, EFJ; HANSEN, TA

A NAD-dependent, oxygen-labile alcohol dehydrogenase was purified from Desulfovibrio gigas. It was decameric, with subunits of M(r) 43,000. The best substrates were ethanol (K(m), 0.15 mM) and 1-propanol (K(m), 0.28 mM). N-terminal amino acid sequence analysis showed that the enzyme belongs to the

Alkali-labile sites and post-irradiation effects in single-stranded DNA induced by H radicals

International Nuclear Information System (INIS)

Lafleur, M.V.M.; Heuvel, N. van; Woldhuis, J.; Loman, H.

1978-01-01

Single-stranded phiX174 DNA in aqueous solutions has been irradiated in the absence of oxygen, under conditions in which H radicals react with the DNA. It was shown that H radical reactions result in breaks, which contribute approximately 10 per cent inactivation. Further, two types of alkali-labile sites were formed. One was lethal and gave rise to single-strand breaks by alkali and was most probably identical with post-irradiation heat damage and contributed about 33 per cent to the inactivation mentioned above. The other consisted of non-lethal damage, partly dihydropyrimidine derivatives, and was converted to lethal damage by alkali. This followed from experiments in which the DNA was treated with osmium-tetroxide, which oxidized thymine to 5,6-dihydroxydihydrothymine. Treatment with alkali of this DNA gave the same temperature dependence as found for the non-lethal alkali-labile sites in irradiated DNA. A similar temperature dependence was found for dihydrothymine and irradiated pyrimidines with alkali. (author)

CD44 Binding to Hyaluronic Acid Is Redox Regulated by a Labile Disulfide Bond in the Hyaluronic Acid Binding Site.

Directory of Open Access Journals (Sweden)

Helena Kellett-Clarke

Full Text Available CD44 is the primary leukocyte cell surface receptor for hyaluronic acid (HA, a component of the extracellular matrix. Enzymatic post translational cleavage of labile disulfide bonds is a mechanism by which proteins are structurally regulated by imparting an allosteric change and altering activity. We have identified one such disulfide bond in CD44 formed by Cys77 and Cys97 that stabilises the HA binding groove. This bond is labile on the surface of leukocytes treated with chemical and enzymatic reducing agents. Analysis of CD44 crystal structures reveal the disulfide bond to be solvent accessible and in the-LH hook configuration characteristic of labile disulfide bonds. Kinetic trapping and binding experiments on CD44-Fc chimeric proteins show the bond is preferentially reduced over the other disulfide bonds in CD44 and reduction inhibits the CD44-HA interaction. Furthermore cells transfected with CD44 no longer adhere to HA coated surfaces after pre-treatment with reducing agents. The implications of CD44 redox regulation are discussed in the context of immune function, disease and therapeutic strategies.

Transpiration and water-use efficiency in mixed-species forests versus monocultures: effects of tree size, stand density and season.

Science.gov (United States)

Forrester, David I

2015-03-01

Mixtures can be more productive than monocultures and may therefore use more water, which may make them more susceptible to droughts. The species interactions that influence growth, transpiration and water-use efficiency (WUE, tree growth per unit transpiration) within a given mixture vary with intra- and inter-annual climatic variability, stand density and tree size, but these effects remain poorly quantified. These relationships were examined in mixtures and monocultures of Eucalyptus globulus Labill. and Acacia mearnsii de Wildeman. Growth and transpiration were measured between ages 14 and 15 years. All E. globulus trees in mixture that were growing faster than similar sized trees in monocultures had higher WUE, while trees with similar growth rates had similar WUE. By the age of 14 years A. mearnsii trees were beginning to senesce and there were no longer any relationships between tree size and growth or WUE. The relationship between transpiration and tree size did not differ between treatments for either species, so stand-level increases in transpiration simply reflected the larger mean tree size in mixtures. Increasing neighbourhood basal area increased the complementarity effect on E. globulus growth and transpiration. The complementarity effect also varied throughout the year, but this was not related to the climatic seasonality. This study shows that stand-level responses can be the net effect of a much wider range of individual tree-level responses, but at both levels, if growth has not increased for a given species, it appears unlikely that there will be differences in transpiration or WUE for that species. Growth data may provide a useful initial indication of whether mixtures have higher transpiration or WUE, and which species and tree sizes contribute to this effect. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Cutting forces during turning with variable depth of cut

Directory of Open Access Journals (Sweden)

M. Sadílek

2016-03-01

The proposed research for the paper is an experimental work – measuring cutting forces and monitoring of the tool wear on the cutting edge. It compares the turning where standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied.

Rapid, labile, and protein synthesis-independent short-term memory in conditioned taste aversion.

Science.gov (United States)

Houpt, T A; Berlin, R

1999-01-01

Short-term memory is a rapid, labile, and protein-synthesis-independent phase of memory. The existence of short-term memory in conditioned taste aversion (CTA) learning has not been demonstrated formally. To determine the earliest time at which a CTA is expressed, we measured intraoral intake of sucrose at 15 min, 1 hr, 6 hr, or 48 h after contingent pairing of an intraoral infusion of 5% sucrose (6.6 ml over 6 min) and toxic lithium chloride injection (76 mg/kg). Rats were implanted with intraoral catheters to allow presentation of taste solutions at arbitrary times. Intraoral intake was measured under conditions of long-delay, single-trial learning typical of CTA. Rats decreased intraoral intake of sucrose at 15 min after contingent pairing of sucrose and LiCl, but not after noncontingent LiCl or sucrose. Thus CTA learning can be expressed rapidly. To determine if short-term CTA memory is labile and decays in the absence of long-term memory, we measured intraoral intake of sucrose after pairing sucrose with low doses of LiCl. Rats received an intraoral infusion of 5% sucrose (6 ml/6 min); 30 min later LiCl was injected at three different doses (19, 38, or 76 mg/kg). A second intraoral infusion of sucrose was administered 15 min, 1 hr, 3 hr, 4.5 hr, 6 hr, or 48 hr later. The formation of long-term CTA memory was dependent on the dose of LiCl paired with sucrose during acquisition. Low doses of LiCl induced a CTA that decayed within 6 hr after pairing. Central administration of the protein synthesis inhibitor cycloheximide prior to LiCl injection blocked long-term CTA expression at 6 and 48 hr, but not short-term CTA expression at 1 hr. Thus, short-term memory for CTA learning exists that is acquired rapidly and independent of protein synthesis, but labile in the absence of long-term memory formation.

Rhizosphere Environment and Labile Phosphorus Release from Organic Waste-Amended Soils.

Science.gov (United States)

Dao, Thanh H.

2015-04-01

Crop residues and biofertilizers are primary sources of nutrients for organic crop production. However, soils treated with large amounts of nutrient-enriched manure have elevated phosphorus (P) levels in regions of intensive animal agriculture. Surpluses occurred in these amended soils, resulting in large pools of exchangeable inorganic P (Pi) and enzyme-labile organic P (Po) that averaging 30.9 and 68.2 mg kg-1, respectively. Organic acids produced during crop residue decomposition can promote the complexation of counter-ions and decouple and release unbound Pi from metal and alkali metal phosphates. Animal manure and cover crop residues also contain large amounts of soluble organic matter, and likely generate similar ligands. However, a high degree of heterogeneity in P spatial distribution in such amended fields, arising from variances in substrate physical forms ranging from slurries to dried solids, composition, and diverse application methods and equipment. Distinct clusters of Pi and Po were observed, where accumulation of the latter forms was associated with high soil microbial biomass C and reduced phosphomonoesterases' activity. Accurate estimates of plant requirements and lability of soil P pools, and real-time plant and soil P sensing systems are critical considerations to optimally manage manure-derived nutrients in crop production systems. An in situ X-ray fluorescence-based approach to sensing canopy and soil XRFS-P was developed to improve the yield-soil P relationship for optimal nutrient recommendations in addition to allowing in-the-field verification of foliar P status.

Cutting method and cutting device for spent fuel rod of nuclear reactor

International Nuclear Information System (INIS)

Komatsu, Masahiko; Ose, Toshihiko.

1996-01-01

A control rod transferred under water in a vertically suspended state is postured horizontally at such a water depth that radiations can be shielded, and then it is cut to a dropping speed limiting portion and a cross-like main body. The separated cross-like main body portion is further cut in the longitudinal direction and separated into a pair of cut pieces each having an L-shaped cross section. A disk like metal saw is used as a cutting tool. Alternatively, a plasma jet cutter or a melting-type water jet cutter is used as a cutting tool. Then, since the spent control rod to be cut is postured horizontally under water, the water depth for the cutting position can be reduced. As a result, the cutting state using the cutting tool can be observed by naked eyes from the position above the water surface thereby enabling to perform the cutting operation reliably. (N.H.)

Changes in labile soil organic matter fractions following land use change from monocropping to poplar-based agroforestry systems in a semiarid region of Northeast China.

Science.gov (United States)

Mao, Rong; Zeng, De-Hui; Li, Lu-Jun; Hu, Ya-Lin

2012-11-01

Labile fractions of soil organic matter (SOM) respond rapidly to land management practices and can be used as a sensitive indicator of changes in SOM. However, there is little information about the effect of agroforestry practices on labile SOM fractions in semiarid regions of China. In order to test the effects of land use change from monocropping to agroforestry systems on labile SOM fractions, we investigated soil microbial biomass C (MBC) and N, particulate organic matter C (POMC) and N (POMN), as well as total organic C (TOC) and total N (TN) in the 0- to 15-cm and the 15- to 30-cm layers in 4-year-old poplar-based agroforestry systems and adjoining monocropping systems with two different soil textures (sandy loam and sandy clay loam) in a semiarid region of Northeast China. Our results showed that poplar-based agroforestry practices affected soil MBC, POMC, and POMN, albeit there was no significant difference in TOC and TN. Agroforestry practices increased MBC, POMC, and POMN in sandy clay loam soils. However, in sandy loam soils, agroforestry practices only increased MBC and even decreased POMC and POMN at the 0- to 15-cm layer. Our results suggest that labile SOM fractions respond sensitively to poplar-based agroforestry practices and can provide early information about the changes in SOM in semiarid regions of Northeast China and highlight that the effects of agroforestry practices on labile SOM fractions vary with soil texture.

Flexible Laser Metal Cutting

DEFF Research Database (Denmark)

Villumsen, Sigurd; Jørgensen, Steffen Nordahl; Kristiansen, Morten

2014-01-01

This paper describes a new flexible and fast approach to laser cutting called ROBOCUT. Combined with CAD/CAM technology, laser cutting of metal provides the flexibility to perform one-of-a-kind cutting and hereby realises mass production of customised products. Today’s laser cutting techniques...... possess, despite their wide use in industry, limitations regarding speed and geometry. Research trends point towards remote laser cutting techniques which can improve speed and geometrical freedom and hereby the competitiveness of laser cutting compared to fixed-tool-based cutting technology...... such as punching. This paper presents the concepts and preliminary test results of the ROBOCUT laser cutting technology, a technology which potentially can revolutionise laser cutting....

Contribution of single-strand breaks and alkali-labile bonds to the loss of infectivity of γ-irradiated phiX174 RF-DNA in E. coli cells mutant in various repair functions

International Nuclear Information System (INIS)

McKee, R.H.

1975-01-01

Twenty-one radiation sensitive mutants have been examined for their capacity to support gamma-irradiated phiX174 RF-DNA. The survival of phiX174 RF-DNA was reduced in essentially all of the sensitive mutants. The irradiated phiX174 RF-DNA was then separated into populations containing either single-strand breaks or alkali-labile bonds to examine the capacity of the mutants to repair each of the classes of lesions. It was found that all E. coli strains are unable to repair 22 percent of the single-strand breaks and all sensitive mutants are unable to repair an additional 10 percent of the breaks. All the repair functions examined are involved in single-strand break repair and none are more or less necessary than any of the others. PhiX174 RF-DNA is also inactivated by alkali-labile bonds. In the normal strains the inactivation efficiency is 0.16 lethal events per lesion with a threshold dose of 15 to 20 krads. The mutants are divided into two classes by their sensitivity to alkali-labile bonds. Both classes of mutants are also inactivated by alkali-labile bonds with efficiencies of about 0.17 and 0.29 lethal events per lesion, respectively. It is proposed that the differences seen in survival curves of phiX174 measured in the sensitive mutants is due to this difference. Although in normal cells the efficiency of inactivation of phiX174 by single-strand breaks is 50 percent greater than by alkali-labile bonds, alkali-labile bonds are produced at approximately twice the rate of single-strand breaks so alkali-labile bonds account for about 61 percent of the overall inactivation. In the mutants of least sensitivity alkali-labile bonds account for about 54 percent of the inactivating events and in the most sensitive about 67 percent

Evolution of phenotypic plasticity and environmental tolerance of a labile quantitative character in a fluctuating environment.

Science.gov (United States)

Lande, R

2014-05-01

Quantitative genetic models of evolution of phenotypic plasticity are used to derive environmental tolerance curves for a population in a changing environment, providing a theoretical foundation for integrating physiological and community ecology with evolutionary genetics of plasticity and norms of reaction. Plasticity is modelled for a labile quantitative character undergoing continuous reversible development and selection in a fluctuating environment. If there is no cost of plasticity, a labile character evolves expected plasticity equalling the slope of the optimal phenotype as a function of the environment. This contrasts with previous theory for plasticity influenced by the environment at a critical stage of early development determining a constant adult phenotype on which selection acts, for which the expected plasticity is reduced by the environmental predictability over the discrete time lag between development and selection. With a cost of plasticity in a labile character, the expected plasticity depends on the cost and on the environmental variance and predictability averaged over the continuous developmental time lag. Environmental tolerance curves derived from this model confirm traditional assumptions in physiological ecology and provide new insights. Tolerance curve width increases with larger environmental variance, but can only evolve within a limited range. The strength of the trade-off between tolerance curve height and width depends on the cost of plasticity. Asymmetric tolerance curves caused by male sterility at high temperature are illustrated. A simple condition is given for a large transient increase in plasticity and tolerance curve width following a sudden change in average environment. © 2014 The Author. Journal of Evolutionary Biology © 2014 European Society For Evolutionary Biology.

Some possibilities for determining cutting data when using laser cutting:

OpenAIRE

Radovanović, Miroslav

2006-01-01

The technological problems faced in the field of the application of laser-cutting machines lie in insufficient knowledge of the laser technique and the absence of both sufficiently reliable practical data and knowledge about the parameters affecting the work process itself. A significant parameter that is necessary to determine and to enter in an NC-program is the cutting speed. Various authors analyze the laser-cutting process and give mathematical models where laser cutting is modeled by us...

Distribution of dissolved labile and particulate iron and copper in Terra Nova Bay polynya (Ross Sea, Antarctica) surface waters in relation to nutrients and phytoplankton growth

Science.gov (United States)

Rivaro, Paola; Ianni, Carmela; Massolo, Serena; Abelmoschi, M. Luisa; De Vittor, Cinzia; Frache, Roberto

2011-05-01

The distribution of the dissolved labile and of the particulate Fe and Cu together with dissolved oxygen, nutrients, chlorophyll a and total particulate matter was investigated in the surface waters of Terra Nova Bay polynya in mid-January 2003. The measurements were conducted within the framework of the Italian Climatic Long-term Interactions of the Mass balance in Antarctica (CLIMA) Project activities. The labile dissolved fraction was operationally defined by employing the chelating resin Chelex-100, which retains free and loosely bound trace metal species. The dissolved labile Fe ranges from below the detection limit (0.15 nM) to 3.71 nM, while the dissolved labile Cu from below the detection limit (0.10 nM) to 0.90 nM. The lowest concentrations for both metals were observed at 20 m depth (the shallowest depth for which metals were measured). The concentration of the particulate Fe was about 5 times higher than the dissolved Fe concentration, ranging from 0.56 to 24.83 nM with an average of 6.45 nM. The concentration of the particulate Cu ranged from 0.01 to 0.71 nM with an average of 0.17 nM. The values are in agreement with the previous data collected in the same area. We evaluated the role of the Fe and Cu as biolimiting metals. The N:dissolved labile Fe ratios (18,900-130,666) would or would not allow a complete nitrate removal, on the basis of the N:Fe requirement ratios that we calculated considering the N:P and the C:P ratios estimated for diatoms. This finding partially agrees with the Si:N ratio that we found (2.29). Moreover we considered a possible influence of the dissolved labile Cu on the Fe uptake process.

Remote Laser Cutting of CFRP: Improvements in the Cut Surface

Science.gov (United States)

Stock, Johannes; Zaeh, Michael F.; Conrad, Markus

In the automotive industry carbon fibre reinforced plastics (CFRP) are considered as a future key material to reduce the weight of the vehicle. Therefore, capable production techniques are required to process this material in mass industry. E.g., state of the art methods for cutting are limited by the high tool wear or the feasible feed rate. Laser cutting processes are still under investigation. This paper presents detailed new studies on remote laser cutting of CFRP focusing on the influence of the material properties and the quality of the cut surface. By adding light absorbing soot particles to the resin of the matrix, the cutting process is improved and fewer defects emerge.

Multibeam Fibre Laser Cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre......-laser cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single...

Multibeam fiber laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Hansen, Klaus Schütt; Nielsen, Jakob Skov

2009-01-01

The appearance of the high power high brilliance fiber laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating Cutting laser, the CO2 laser. However, quality problems in fiber......-laser cutting have until now limited its application to metal cutting. In this paper the first results of proof-of-principle Studies applying a new approach (patent pending) for laser cutting with high brightness and short wavelength lasers will be presented. In the approach, multibeam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from two single mode fiber lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W...

Cutting cleaner

International Nuclear Information System (INIS)

Elsen, R.P.H. van; Smits, M.

1991-01-01

This paper presents the results of a long term field test of the Cutting Cleaner, which is used for the treatment of wet oil contaminated cuttings (WOCC) produced when drilling with Oil Based Mud (OBM). It was concluded that it is possible to reduce the oil content of cuttings to an average of 1 - 2%. The recovered base oil can be reused to make new oil based mud

GM1 erythroimmunoassay for detection and titration of Escherichia coli heat-labile enterotoxin.

OpenAIRE

Germani, Y; Bégaud, E; Guesdon, J L; Moreau, J P

1986-01-01

A GM1 ganglioside erythroimmunoassay for the detection of heat-labile Escherichia coli enterotoxin (LT) was developed for use in poorly equipped laboratories in developing countries. This assay is based on the immunological similarity between Vibrio cholerae toxin and LT and uses cholera toxin antiserum and sheep anti-rabbit immunoglobulin covalently coupled to sheep erythrocytes as conjugate. This assay has the following advantages over other currently available techniques: the reagents it u...

Laser cutting or water-jet cutting. Laser setsudan ka water-jet setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Yamada, T. (Shibuya Kogyo Co. Ltd., Ishikawa (Japan))

1991-05-01

The recent spread of carbon oxide laser cutter is so startlingly fast, but at the same time, water jet cutting using ultra high pressure water stream is drawing attention as it has identical characteristics, and opens the way to cutting materials that have been hitherto difficult to cut. The authors, who are fabricators of cutters of both types, gave the comparisons and explanations on several examples referring to materials that can be cut, cutting accuracy, speed, shape and thermal effects to cut face, and running cost in detail. However, simple comparison is difficult. For instance, cutting 6 mm thick SUS sheet costs a running cost of 65 yen per meter in laser cutting, and 535 yen per meter in water jet cutting, but this situation is often reversed when other material or sheet thickness is selected. The actual situation in the sheet metal processing industry at the present time is that it uses by far more laser processing machines, and uses water jet cutters to supplement for cutting materials more difficult to cut. 10 figs., 3 tabs.

Decrease of labile Zn and Cd in the rhizosphere of hyperaccumulating Thlaspi caerulescens with time

Energy Technology Data Exchange (ETDEWEB)

Dessureault-Rompre, Jacynthe, E-mail: dessureaultromj@agr.gc.c [Institute of Terrestrial Ecosystems (ITES), ETH Zurich, Universitaetstrasse 16, CH-8092 Zuerich (Switzerland); Luster, Joerg, E-mail: joerg.luster@wsl.c [Swiss Federal Institute for Forest, Snow, and Landscape Research (WSL), Zuercherstrasse 111, CH-8903 Birmensdorf (Switzerland); Schulin, Rainer, E-mail: rainer.schulin@env.ethz.c [Institute of Terrestrial Ecosystems (ITES), ETH Zurich, Universitaetstrasse 16, CH-8092 Zuerich (Switzerland); Tercier-Waeber, Mary-Lou, E-mail: marie-louise.tercier@unige.c [CABE, Department of Inorganic and Analytical Chemistry, Sciences II, University of Geneva, 30 quai Ernest Ansermet, CH-1211 Geneva 4 (Switzerland); Nowack, Bernd, E-mail: bernd.nowack@empa.c [Institute of Terrestrial Ecosystems (ITES), ETH Zurich, Universitaetstrasse 16, CH-8092 Zuerich (Switzerland); Empa - Swiss Federal Laboratories for Materials Testing and Research, Lerchenfeldstrasse 5, CH-9014 St. Gallen (Switzerland)

2010-05-15

By using a rhizobox micro-suction cup technique we studied in-situ mobilization and complexation of Zn and Cd in the rhizosphere of non-hyperaccumulating Thlaspi perfoliatum and two different Thlaspi caerulescens ecotypes, one of them hyperaccumulating Zn, the other Zn and Cd. The dynamic fraction (free metal ions and small labile complexes) of Zn and Cd decreased with time in the rhizosphere solution of the respective hyperaccumulating T. caerulescens ecotypes, and at the end of the experiment, it was significantly smaller than in the other treatments. Furthermore, the rhizosphere solutions of the T. caerulescens ecotypes exhibited a higher UV absorptivity than the solution of the T. perfoliatum rhizosphere and the plant-free soil. Based on our findings we suggest that mobile and labile metal-dissolved soil organic matter complexes play a key role in the rapid replenishment of available metal pools in the rhizosphere of hyperaccumulating T. caerulescens ecotypes, postulated earlier. - A mechanism that explains the rapid replenishment of metal pools accessible by hyperaccumulator plants for phytoextraction is proposed.

β-Adrenergic signaling is required for the induction of a labile state during memory reconsolidation.

Science.gov (United States)

Lim, Chae-Seok; Kim, Jae-Ick; Kwak, Chuljung; Lee, Jaehyun; Jang, Eun Hae; Oh, Jihae; Kaang, Bong-Kiun

2018-04-20

Memory reconsolidation is the process by which previously consolidated memories reenter a labile state through reactivation of the memory trace and are actively consolidated through de novo protein synthesis. Although extensive studies have shown that β-adrenergic signaling plays a critical role in the restabilization of reactivated memory, its role in the destabilization of long-term memory is not well-studied. In this study, we found that membrane excitability increased in hippocampal CA1 neurons immediately after the retrieval of contextual fear memory. Interestingly, this increase in membrane excitability diminished after treatment with propranolol (a β-adrenergic receptor antagonist), an NMDA receptor antagonist, and a PKA inhibitor. In addition, we found that administration of propranolol prior to, but not after, the retrieval of fear memory ameliorated the memory impairment caused by anisomycin, indicating that inhibition of β-adrenergic signaling blocks the destabilization of contextual fear memory. Taken together, these results indicate that β-adrenergic signaling via NMDA receptors and PKA signaling pathway induces a labile state of long-term memory through increased neuronal membrane excitability. Copyright © 2018 Elsevier Inc. All rights reserved.

Can Biochar Protect Labile Organic Matter Against Mineralization in Soil?

Institute of Scientific and Technical Information of China (English)

Giovanna B.MELAS; Oriol ORTIZ; Josep M.ALACA(N)IZ

2017-01-01

Biochar could help to stabilize soil organic (SOM) matter,thus sequestering carbon (C) into the soil.The aim of this work was to determine an easy method i) to estimate the effects of the addition of biochar and nutrients on the organic matter (SOM)mineralization in an artificial soil,proposed by the Organization for Economic Co-operation and Development (OECD),amended with glucose and ii) to measure the amount of labile organic matter (glucose) that can be sorbed and thus be partially protected in the same soil,amended or not amended with biochar.A factorial experiment was designed to check the effects of three single factors (biochar,nutrients,and glucose) and their interactions on whole SOM mineralization.Soil samples were inoculated with a microbial inoculum and preincubated to ensure that their biological activities were not limited by a small amount of microbial biomass,and then they were incubated in the dark at 21 ℃ for 619 d.Periodical measurements of C mineralized to carbon dioxide (CO2) were carried out throughout the 619-d incubation to allow the mineralization of both active and slow organic matter pools.The amount of sorbed glucose was calculated as the difference between the total and remaining amounts of glucose added in a soil extract.Two different models,the Freundlich and Langmuir models,were selected to assess the equilibrium isotherms of glucose sorption.The CO2-C release strongly depended on the presence of nutrients only when no biochar was added to the soil.The mineralization of organic matter in the soil amended with both biochar and glucose was equal to the sum of the mineralization of the two C sources separately.Furthermore,a significant amount of glucose can be sorbed on the biochar-amended soil,suggesting the involvement of physico-chemical mechanisms in labile organic matter protection.

Technology development for cutting a reactor pressure vessel using a mechanical cutting technique

International Nuclear Information System (INIS)

Watanabe, Masaaki; Miyasaka, Yasuhiko; Miyao, Hidehiko; Ooki, Arahiko; Ninomiya, Toshiaki; Koiwai, Masami

2001-01-01

On decommissioning of nuclear facilities, the thermal cutting technique such as an oxygen-acetylene gas cutting and a plasma arc cutting are generally used for cutting massive and thick steel structures in consideration with cutting speed and control performance. These techniques generate dust, smoke, aerosol and a large quantity of secondary waste. Mechanical cutting technique has an advantage of small amount of secondary waste, and the metal chips from the kerf recovered easily compared with these thermal cutting technique. The remote mechanical cutting system for highly activated RPV has been developed with the manner which achieves the safety and cost effectiveness. The development has been performed on consignment to RANDEC from the Science and Technology Agency of Japan. (author)

Occurrence and abundance of carbohydrates and amino compounds in sequentially extracted labile soil organic matter fractions.

Science.gov (United States)

This study aimed to investigate the content of carbohydrates and amino compounds in three labile fraction of soil organic matter (SOM). Soil samples were collected from two agricultural fields in southern Italy and the light fraction (LF), the 500–53-µm particulate organic matter (POM) and the mobil...

Machining of Some Difficult-to-Cut Materials with Rotary Cutting Tools

OpenAIRE

Stjernstoft, Tero

2004-01-01

Automobile and aero industries have an increasing interestin materials with improved mechanical properties. However, manyof these new materials are classified as difficult-to-cut withconventional tools. It is obvious that tools, cutting processesand cutting models has to be devel-oped parallel to materialsscience. In this thesis rotary cutting tools are tested as analternative toexpensive diamond or cubic bore nitridetools. Metal matrix composites mostly consist of a light metalalloy (such as...

DETERMINACIÓN DE MEDIOS DE CULTIVO Y PH PARA LA MASIFICACIÓN in vitro DE CEPAS DE Suillus luteus Aubl. ASOCIADAS A Pinus radiata D. Don Y Scleroderma citrinum Pers. ASOCIADAS A Eucalyptus globulus Labill. DE LA REGIÓN DEL BIOBÍO, CHILE

Directory of Open Access Journals (Sweden)

Marta González

2015-02-01

Full Text Available El uso de agentes biológicos en la producción en vivero ha aflorado como un elemento que permite no sólo mejorar la calidad morfológica y fisiológica de las plantas, sino que también posibilitar un mayor éxito en el ámbito silvicultural de una plantación. Estos agentes biológicos requieren de un ambiente óptimo para crecer, asociarse y reproducirse. El objetivo de este estudio fue determinar la dependencia del pH y el medio de cultivo en el crecimiento in vitro de distintas cepas de Suillus luteus y Scleroderma citrinum asociadas a Pinus radiata y Eucalyptus globulus, respectivamente. El estudio se realizó en condiciones controladas de temperatura y humedad, disponiendo los inóculos en placas Petri con diferentes medios cultivo, evaluando parámetros de crecimiento y biomasa a los 38 días para S. luteus y 105 días para S. citrinum. Los resultados indican que tanto el medio de cultivo, el pH del medio, así como las cepas de cada especie estudiada, son determinantes en las respuestas de crecimiento de los hongos ectomicorrícicos in vitro evaluados. Las cepas de S. luteus se desarrollaron adecuadamente en un medio de cultivo con abundancia de nutrientes (BAF, MMN como en baja presencia de ellos (EMA, y con pH más bien ácido (4,8 y 5,8. Por otro lado, las cepas de S. citrinum presentaron, para los mismos ambientes, un desarrollo inferior y lento, no obstante, la cepa Sc8 se reprodujo de forma óptima y rápida bajo un medio de cultivo BAF y con un pH moderadamente ácido de 5,8.

Minimizing waste (off-cuts using cutting stock model: The case of one dimensional cutting stock problem in wood working industry

Directory of Open Access Journals (Sweden)

Gbemileke A. Ogunranti

2016-09-01

Full Text Available Purpose: The main objective of this study is to develop a model for solving the one dimensional cutting stock problem in the wood working industry, and develop a program for its implementation. Design/methodology/approach: This study adopts the pattern oriented approach in the formulation of the cutting stock model. A pattern generation algorithm was developed and coded using Visual basic.NET language. The cutting stock model developed is a Linear Programming (LP Model constrained by numerous feasible patterns. A LP solver was integrated with the pattern generation algorithm program to develop a one - dimensional cutting stock model application named GB Cutting Stock Program. Findings and Originality/value: Applying the model to a real life optimization problem significantly reduces material waste (off-cuts and minimizes the total stock used. The result yielded about 30.7% cost savings for company-I when the total stock materials used is compared with the former cutting plan. Also, to evaluate the efficiency of the application, Case I problem was solved using two top commercial 1D-cutting stock software.  The results show that the GB program performs better when related results were compared. Research limitations/implications: This study round up the linear programming solution for the number of pattern to cut. Practical implications: From Managerial perspective, implementing optimized cutting plans increases productivity by eliminating calculating errors and drastically reducing operator mistakes. Also, financial benefits that can annually amount to millions in cost savings can be achieved through significant material waste reduction. Originality/value: This paper developed a linear programming one dimensional cutting stock model based on a pattern generation algorithm to minimize waste in the wood working industry. To implement the model, the algorithm was coded using VisualBasic.net and linear programming solver called lpsolvedll (dynamic

Redox-active labile iron in fortified flours from the Brazilian market Ferro lábil redox-ativo em farinhas fortificadas do mercado brasileiro

Directory of Open Access Journals (Sweden)

Breno Pannia Espósito

2007-08-01

Full Text Available OBJECTIVE: To quantify the fraction of redox-active labile iron in iron-fortified flours acquired on the Brazilian market. METHODS: Samples of wheat flour, maize flour and breadcrumbs were extracted with buffers that mimic gastric juice, saliva and intestinal juice. Redox-active labile iron levels were assessed through the reaction of autoxidation of ascorbic acid catalyzed by iron in the presence of a fluorescence probe. RESULTS: Redox-active labile iron represents 1% to 9% of the total iron in the flour and breadcrumb samples, with the lowest values found under gastric juice conditions and the highest in the more alkaline media. Redox-active labile iron possibly arises from the decomposition of an iron-phytic acid complex. A positive correlation between redox-active labile iron and total iron was found in saline biomimetic fluids. CONCLUSION: Redox-active labile iron may be a risk factor for people with impaired antioxidant defenses, such as those who are atransferrinemic or iron overloaded (e.g. thalassemic. Total iron can be used to predict redox-active labile iron absorption at each stage of the gastrointestinal tract after ingestion of iron-fortified flours.OBJETIVO: Quantificar a porcentagem de ferro lábil redox ativo em farinhas fortificadas adquiridas no comércio popular. MÉTODOS: Amostras de farinha de trigo, fubá e rosca foram extraídas com tampões miméticos de suco gástrico, saliva e suco intestinal. Os níveis de ferro lábil redox ativo foram determinados por meio da reação de auto-oxidação do ácido ascórbico catalisada pelo ferro, em presença de uma sonda fluorimétrica. RESULTADOS: A fração de ferro lábil redox ativo representa entre 1% e 9% do ferro total nas farinhas estudadas, sendo os menores valores encontrados em condições miméticas do suco gástrico e os maiores nos meios mais alcalinos. Há indícios de que o ferro lábil redox ativo origina-se da decomposição de um complexo entre ferro e ácido f

Underwater cutting techniques developments

International Nuclear Information System (INIS)

Bach, F.-W.

1990-01-01

The primary circuit structures of different nuclear powerplants are constructed out of stainless steels, ferritic steels, plated ferritic steels and alloys of aluminium. According to the level of the specific radiation of these structures, it is necessary for dismantling to work with remote controlled cutting techniques. The most successful way to protect the working crew against exposure of radiation is to operate underwater in different depths. The following thermal cutting processes are more or less developed to work under water: For ferritic steels only - flame cutting; For ferritic steels, stainless steels, cladded steels and aluminium alloys - oxy-arc-cutting, arc-waterjet-cutting with a consumable electrode, arc-saw-cutting, plasma-arc-cutting and plasma-arc-saw. The flame cutting is a burning process, all the other processes are melt-cutting processes. This paper explains the different techniques, giving a short introduction of the theory, a discussion of the possibilities with the advantages and disadvantages of these processes giving a view into the further research work in this interesting field. (author)

Quantitative chemical exchange saturation transfer (qCEST) MRI--RF spillover effect-corrected omega plot for simultaneous determination of labile proton fraction ratio and exchange rate.

Science.gov (United States)

Sun, Phillip Zhe; Wang, Yu; Dai, ZhuoZhi; Xiao, Gang; Wu, Renhua

2014-01-01

Chemical exchange saturation transfer (CEST) MRI is sensitive to dilute proteins and peptides as well as microenvironmental properties. However, the complexity of the CEST MRI effect, which varies with the labile proton content, exchange rate and experimental conditions, underscores the need for developing quantitative CEST (qCEST) analysis. Towards this goal, it has been shown that omega plot is capable of quantifying paramagnetic CEST MRI. However, the use of the omega plot is somewhat limited for diamagnetic CEST (DIACEST) MRI because it is more susceptible to direct radio frequency (RF) saturation (spillover) owing to the relatively small chemical shift. Recently, it has been found that, for dilute DIACEST agents that undergo slow to intermediate chemical exchange, the spillover effect varies little with the labile proton ratio and exchange rate. Therefore, we postulated that the omega plot analysis can be improved if RF spillover effect could be estimated and taken into account. Specifically, simulation showed that both labile proton ratio and exchange rate derived using the spillover effect-corrected omega plot were in good agreement with simulated values. In addition, the modified omega plot was confirmed experimentally, and we showed that the derived labile proton ratio increased linearly with creatine concentration (p plot for quantitative analysis of DIACEST MRI. Copyright © 2014 John Wiley & Sons, Ltd.

Welding and cutting

International Nuclear Information System (INIS)

Drews, P.; Schulze Frielinghaus, W.

1978-01-01

This is a survey, with 198 literature references, of the papers published in the fields of welding and cutting within the last three years. The subjects dealt with are: weldability of the materials - Welding methods - Thermal cutting - Shaping and calculation of welded joints - Environmental protection in welding and cutting. (orig.) [de

[Computer assisted prescription of labile blood products: What are we expecting?

Science.gov (United States)

Daurat, G

2016-11-01

Computer assisted prescription of labile blood products is just at its beginning. Current programs already allow embedding automatically such data as patient's and prescribers' identification or ward details to produce readable prescriptions, also complying with part of Good Practice guidelines. Now prescriptions can also be sent electronically to the Etablissement Francais du Sang, the French blood products services. Usually they are computer programs specialised in transfusion and interfaced with the main patient's file software. Hardly ever the main software is able to manage transfusion itself. Next step would consist in performing checks, calculations or displaying warning or help messages based on academic or local medical recommendations or even tailored to pre-defined individual requirements. But these call for direct access to patient's data such as diagnosis or tests results, that must be accurately classified and coded before use. The main software could provide such functionalities: but actually that would be infrequent and difficult to transpose from one hospital to the other, regarding to the diversity of main software and their settings. Another solution would be to enhance the very few transfusion specialised programs in order to assist prescribers. Data could be prepared and sent by the main software according to a standardised format each time a prescription is to be entered. This standardised format should be independent from software in order to ensure interoperability, whatever the main and specialised programs. The content and format of this data exchange has to be defined, but this would allow hundreds of hospitals to provide a comprehensive tool for prescription of labile blood products, regardless of their main patient's file software. Copyright © 2016. Published by Elsevier SAS.

Cutting assembly

Science.gov (United States)

Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

1984-01-01

A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

Restraining and neck cutting or stunning and neck cutting of veal calves.

Science.gov (United States)

Lambooij, E; van der Werf, J T N; Reimert, H G M; Hindle, V A

2012-05-01

Brain and heart activities were measured in 31 veal calves during restraining and rotating followed by neck cutting with or without stunning to evaluate welfare. After neck cutting correlation dimension analyses and %power of EEG beta wave fraction decreased gradually to lower values resulting in an induction of unconsciousness lasting on average 80s. Corneal reflex response ceased 135±57s after neck cutting. The CD scores and the %power of beta waves fell immediately after post-cut captive bolt and pre-cut electrical stunning to levels indicating unconsciousness. Heart rate in lairage increased upon entrance to the restrainer and again after rotation, heart rate variability decreased. Rotating the restrainer 90°, 120° or 180° compromised veal calf welfare and should be avoided. It is recommended to use post-cut captive bolt stunning or pre-cut electrical stunning inducing immediate unconsciousness. Copyright © 2011 Elsevier Ltd. All rights reserved.

Acid-Labile Acyclic Cucurbit[n]uril Molecular Containers for Controlled Release.

Science.gov (United States)

Mao, Dake; Liang, Yajun; Liu, Yamin; Zhou, Xianhao; Ma, Jiaqi; Jiang, Biao; Liu, Jia; Ma, Da

2017-10-02

Stimuli-responsive molecular containers are of great importance for controlled drug delivery and other biomedical applications. A new type of acid labile acyclic cucurbit[n]uril (CB[n]) molecular containers is presented that can degrade and release the encapsulated cargo at accelerated rates under mildly acidic conditions (pH 5.5-6.5). These containers retain the excellent recognition properties of CB[n]-type hosts. A cell culture study demonstrated that the cellular uptake of cargos could be fine-tuned by complexation with different containers. The release and cell uptake of cargo dye was promoted by acidic pH. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Paper Cuts.

Science.gov (United States)

Greene, Lisa A.

1990-01-01

Describes how to create paper cuts and suggests the most appropriate materials for young children that give good quality results. Describes the methods the author, a professional artist, uses to assemble her own paper cuts and how these can be adopted by older students. (KM)

Operation of the AM-50 cutting head under different cutting conditions

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Kusz, F; Fels, M

1988-02-01

Presents results of investigations into operation of the AM-50 heading machine. About 50% of headings, i.e. about 800 km/a, are driven by about 400 heading machines. It has been found that energy consumption depends on compression strength of rock and is 6 times higher for sandstone than for clayey shale. Power consumed by cutting heads depends mainly on the web used (30-150 mm depending on rock strength). Wear of cutting tools is 1-30 pieces per meter of heading advance at a working cross-section area of 15 m/sup 2/. The AM-50 machine uses cutting speeds of 1.1-3.5 m/s. Higher speeds negatively affect the resistance to cutting. Nonuniform tool wear on the cutting head circumference is an indication of improper head design that requires remedying.

Wet cutting

Energy Technology Data Exchange (ETDEWEB)

Hole, B. [IMC Technical Services (United Kingdom)

1999-08-01

Continuous miners create dust and methane problems in underground coal mining. Control has usually been achieved using ventilation techniques as experiments with water based suppression have led to flooding and electrical problems. Recent experience in the US has led to renewed interest in wet head systems. This paper describes tests of the Hydraphase system by IMC Technologies. Ventilation around the cutting zone, quenching of hot ignition sources, dust suppression, the surface trial gallery tests, the performance of the cutting bed, and flow of air and methane around the cutting head are reviewed. 1 ref., 2 figs., 2 photos.

Fundamentals of cutting.

Science.gov (United States)

Williams, J G; Patel, Y

2016-06-06

The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology.

A Longitudinal Study of Emotion Regulation, Emotion Lability-Negativity, and Internalizing Symptomatology in Maltreated and Nonmaltreated Children

Science.gov (United States)

Kim-Spoon, Jungmeen; Cicchetti, Dante; Rogosch, Fred A.

2013-01-01

The longitudinal contributions of emotion regulation and emotion lability-negativity to internalizing symptomatology were examined in a low-income sample (171 maltreated and 151 nonmaltreated children, from age 7 to 10 years). Latent difference score models indicated that for both maltreated and nonmaltreated children, emotion regulation was a…

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete.

Science.gov (United States)

Sánchez Egea, A J; Martynenko, V; Martínez Krahmer, D; López de Lacalle, L N; Benítez, A; Genovese, G

2018-02-09

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade's matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria.

Emotional Lability in Patients with Attention-Deficit/Hyperactivity Disorder: Impact of Pharmacotherapy.

Science.gov (United States)

Childress, Ann C; Sallee, Floyd R

2015-08-01

Attention-deficit/hyperactivity disorder (ADHD) is a neurobehavioral disorder defined by persistent inattention and/or hyperactivity and impulsivity. These symptoms occur more frequently and are more severe in individuals with ADHD compared with those at a similar developmental level without ADHD, and can be conceptualized as deficits in executive functioning (EF). EF includes domains of metacognition and inhibition, which influence the ability to regulate responses elicited by emotional stimuli. EF deficits can lead to emotional lability (EL), which is characterized by sudden changes in emotion and behaviors of inappropriately high intensity that may include sudden bouts of anger, dysphoria, sadness, or euphoria. EL is common and estimated to occur in about 3.3-10% of the population. Recent estimates of EL prevalence in children and adolescents with ADHD range from 38 to 75%. The Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition does not include EL in diagnostic criteria for ADHD, but does include ADHD-associated features of low frustration tolerance, irritability, or mood lability. The neurobiological basis of EL is not well understood, but brain imaging studies support dividing EF into "cool" cognitive networks encompassing attention and planning activities, and "hot" motivational networks involved in temporal discounting, reward processing, and reward anticipation. Dysfunction in "hot" networks is thought to be related to EL. EL symptoms are associated with more severe ADHD and co-morbidities, have significant impact on functioning, and may respond to treatment with medications frequently used to treat ADHD. Treatment outcomes and areas for future research are discussed.

Induction of heat-labile sites in DNA of mammalian cells by the antitumor alkylating drug CC-1065

International Nuclear Information System (INIS)

Zsido, T.J.; Woynarowski, J.M.; Baker, R.M.; Gawron, L.S.; Beerman, T.A.

1991-01-01

CC-1065 is a very potent antitumor antibiotic capable of covalent and noncovalent binding to the minor groove of naked DNA. Upon thermal treatment, covalent adducts formed between CC-1065 and DNA generate strand break. The authors have shown that this molecular damage can be detected following CC-1065 treatment of mammalian whole cells. Using alkaline sucrose gradient analysis, They observe thermally induced breakage of [ 14 C]thymidine-prelabeled DNA from drug-treated African green monkey kidney BSC-1 cells. Very little damage to cellular DNA by CC-1065 can be detected without first heating the drug-treated samples. CC-1065 can also generate heat-labile sites within DNA during cell lysis and heating, subsequent to the exposure of cells to drug, suggesting that a pool of free and noncovalently bound drug is available for posttreatment adduct formation. This effect was controlled for by mixing [ 3 H]thymidine-labeled untreated cells with the [ 14 C]thymidine-labeled drug-treated samples. The lowest drug dose at which heat-labile sites were detected was 3 nM CC-1065 (3 single-stranded breaks/10 6 base pairs). This concentration reduced survival of BSC-1 cells to 0.1% in cytotoxicity assays. The generation of CC-1065-induced lesions in cellular DNA is time dependent (the frequency of lesions caused by a 60 nM treatment reaching a plateau at 2 h) and is not readily reversible. The results of this study demonstrate that CC-1065 does generate heat-labile sites with the cellular DNA of intact cells and suggest that a mechanism of cytotoxic action of CC-1065 involves formation of covalent adducts to DNA

Device for cutting protrusions

Science.gov (United States)

Bzorgi, Fariborz M [Knoxville, TN

2011-07-05

An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade. The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.

Experimental research on the durability cutting tools for cutting-off steel profiles

Directory of Open Access Journals (Sweden)

Cristea Alexandru

2017-01-01

Full Text Available The production lines used for manufacturing U-shaped profiles are very complex and they must have high productivity. One of the most important stages of the fabrication process is the cutting-off. This paper presents the experimental research and analysis of the durability of the cutting tools used for cutting-off U-shaped metal steel profiles. The results of this work can be used to predict the durability of the cutting tools.

Study of Cutting Edge Temperature and Cutting Force of End Mill Tool in High Speed Machining

Directory of Open Access Journals (Sweden)

Kiprawi Mohammad Ashaari

2017-01-01

Full Text Available A wear of cutting tools during machining process is unavoidable due to the presence of frictional forces during removing process of unwanted material of workpiece. It is unavoidable but can be controlled at slower rate if the cutting speed is fixed at certain point in order to achieve optimum cutting conditions. The wear of cutting tools is closely related with the thermal deformations that occurred between the frictional contact point of cutting edge of cutting tool and workpiece. This research paper is focused on determinations of relationship among cutting temperature, cutting speed, cutting forces and radial depth of cutting parameters. The cutting temperature is determined by using the Indium Arsenide (InAs and Indium Antimonide (InSb photocells to measure infrared radiation that are emitted from cutting tools and cutting forces is determined by using dynamometer. The high speed machining process is done by end milling the outer surface of carbon steel. The signal from the photocell is digitally visualized in the digital oscilloscope. Based on the results, the cutting temperature increased as the radial depth and cutting speed increased. The cutting forces increased when radial depth increased but decreased when cutting speed is increased. The setup for calibration and discussion of the experiment will be explained in this paper.

Rapid, Labile, and Protein Synthesis– Independent Short-Term Memory in Conditioned Taste Aversion

OpenAIRE

Houpt, Thomas A.; Berlin, RoseAnn

1999-01-01

Short-term memory is a rapid, labile, and protein-synthesis-independent phase of memory. The existence of short-term memory in conditioned taste aversion (CTA) learning has not been demonstrated formally. To determine the earliest time at which a CTA is expressed, we measured intraoral intake of sucrose at 15 min, 1 hr, 6 hr, or 48 h after contingent pairing of an intraoral infusion of 5% sucrose (6.6 ml over 6 min) and toxic lithium chloride injection (76 mg/kg). Rats were implanted with int...

The Cutting Process, Chips and Cutting Forces in Machining CFRP

DEFF Research Database (Denmark)

Koplev, A.; Lystrup, Aage; Vorm, T.

1983-01-01

The cutting of unidirectional CFRP, perpendicular as well as parallel to the fibre orientation, is examined. Shaping experiments, ‘quick-stop’ experiments, and a new chip preparation technique are used for the investigation. The formation of the chips, and the quality of the machined surface...... is discussed. The cutting forces parallel and perpendicular to the cutting direction are measured for various parameters, and the results correlated to the formation of chips and the wear of the tool....

Experimental Investigation on Cutting Characteristics in Nanometric Plunge-Cutting of BK7 and Fused Silica Glasses.

Science.gov (United States)

An, Qinglong; Ming, Weiwei; Chen, Ming

2015-03-27

Ductile cutting are most widely used in fabricating high-quality optical glass components to achieve crack-free surfaces. For ultra-precision machining of brittle glass materials, critical undeformed chip thickness (CUCT) commonly plays a pivotal role in determining the transition point from ductile cutting to brittle cutting. In this research, cutting characteristics in nanometric cutting of BK7 and fused silica glasses, including machined surface morphology, surface roughness, cutting force and specific cutting energy, were investigated with nanometric plunge-cutting experiments. The same cutting speed of 300 mm/min was used in the experiments with single-crystal diamond tool. CUCT was determined according to the mentioned cutting characteristics. The results revealed that 320 nm was found as the CUCT in BK7 cutting and 50 nm was determined as the size effect of undeformed chip thickness. A high-quality machined surface could be obtained with the undeformed chip thickness between 50 and 320 nm at ductile cutting stage. Moreover, no CUCT was identified in fused silica cutting with the current cutting conditions, and brittle-fracture mechanism was confirmed as the predominant chip-separation mode throughout the nanometric cutting operation.

Analysis of changes in paper cutting forces during the cutting cycle in single-knife guillotine

OpenAIRE

Rusin, Agnieszka; Petriaszwili, Georgij

2013-01-01

Paper presents the results of changes in the three components of cutting forces of paper stacks cutting during the cutting cycle in single-knife guillotine. The changes of the three components of cutting force at different stages of cutting cycle were analyzed.

The dynamics of acid-soluble phosphorus compounds in the course of winter and spring wheat germination under various thermic conditions. Part II. Labile phosphorus after hydrolysis of the acid-soluble fraction

Directory of Open Access Journals (Sweden)

A. Barbaro

2015-06-01

Full Text Available The changes in labile phosphorus compounds content during germination of wheat were investigated. These compounds were determined in acid-soluble germ extracts separated into fractions according to the solubility of their barium salts. Low germination temperature was found to raise the labile phosphorus content in the fraction of insoluble barium salts. If we assume that labile P of this fraction consisted mainly of adenosinedi- and triphosphates, it would seem that the rise, in the ATP and ADP level under the influence of low temperature may be essential for initiating flowering in winter varieties.

Predicting the solubility and lability of Zn, Cd, and Pb in soils from a minespoil-contaminated catchment by stable isotopic exchange

Science.gov (United States)

Marzouk, E. R.; Chenery, S. R.; Young, S. D.

2013-12-01

The Rookhope catchment of Weardale, England, has a diverse legacy of contaminated soils due to extensive lead mining activity over four centuries. We measured the isotopically exchangeable content of Pb, Cd and Zn (E-values) in a large representative subset of the catchment soils (n = 246) using stable isotope dilution. All three metals displayed a wide range of %E-values (c. 1-100%) but relative lability followed the sequence Cd > Pb > Zn. A refinement of the stable isotope dilution approach also enabled detection of non-reactive metal contained within suspended sub-micron (dilution, in a diverse range of soil ecosystems within the catchment of an old Pb/Zn mining area. Assess the controlling influences of soil properties on metal lability and develop predictive algorithms for metal lability in the contaminated catchment based on simple soil properties (such as pH, organic matter (LOI), and total metal content). Examine the incidence of non-isotopically-exchangeable metal held within suspended colloidal particles (SCP-metal) in filtered soil solutions (<0.22 μm) by comparing E-values from isotopic abundance in solutions equilibrated with soil and in a resin phase equilibrated with the separated solution. Assess the ability of a geochemical speciation model, WHAM(VII), to predict metal solubility using isotopically exchangeable metal as an input variable.

Cutting and Self-Harm

Science.gov (United States)

... Your feelings Feeling sad Cutting and self-harm Cutting and self-harm Self-harm, sometimes called self- ... There are many types of self-injury, and cutting is one type that you may have heard ...

Ecosystem partitioning of 15N-glycine after long-term climate and nutrient manipulations, plant clipping and addition of labile carbon in a subarctic heath tundra

DEFF Research Database (Denmark)

Sørensen, Pernille Lærkedal; Michelsen, Anders; Jonasson, Sven Evert

2008-01-01

of nitrogen (N). Here, we studied 15N label incorporation into microbes, plants and soil N pools after both long-term (12 years) climate manipulation and nutrient addition, plant clipping and a pulse-addition of labile C to the soil, in order to gain information on interactions among soil N and C pools...... addition. However, plants exerted control on the soil inorganic N concentrations and recovery of total dissolved 15N (TD15N), and likewise the microbes reduced these soil pools, but only when fed with labile C. Soil microbes in clipped plots were primarily C limited, and the findings of reduced N...... availability, both in the presence of plants and with the combined treatment of plant clipping and addition of sugar, suggest that the plant control of soil N pools was not solely due to plant uptake of soil N, but also partially caused by plants feeding labile C to the soil microbes, which enhanced...

On Permuting Cut with Contraction

OpenAIRE

Borisavljevic, Mirjana; Dosen, Kosta; Petric, Zoran

1999-01-01

The paper presents a cut-elimination procedure for intuitionistic propositional logic in which cut is eliminated directly, without introducing the multiple-cut rule mix, and in which pushing cut above contraction is one of the reduction steps. The presentation of this procedure is preceded by an analysis of Gentzen's mix-elimination procedure, made in the perspective of permuting cut with contraction. It is also shown that in the absence of implication, pushing cut above contraction doesn't p...

Model for Reggeon-Pomeranchukon cuts

International Nuclear Information System (INIS)

Chia, S.

1977-01-01

A model is presented for calculating Reggeon-Pomeranchukon cuts, making use explicitly of the Mandelstam diagram. External spins are treated in a natural way. Calculation for the general case is outlined and it is shown that in practical application the cut can be calculated in a standard way. Cuts associated with the exchanges of π, rho, B, and A 2 are considered, and characteristics of the RP cuts, as well as the structure functions, are extracted and discussed. It is found that the model differs considerably from the absorption model. Two suppression schemes are operative which control the magnitudes of cut contributions to amplitudes with ''naturality'' opposite to the Reggeon. The πP cut is found to be a unique case because of the smallness of the pion mass. In general, the RP cuts are self-conspiratorial. At very high energies, all cuts, except πP cut, exhibit quasifactorization

Emotional Lability in Children and Adolescents with Attention Deficit/Hyperactivity Disorder (ADHD): Clinical Correlates and Familial Prevalence

Science.gov (United States)

Sobanski, Esther; Banaschewski, Tobias; Asherson, Philip; Buitelaar, Jan; Chen, Wai; Franke, Barbara; Holtmann, Martin; Krumm, Bertram; Sergeant, Joseph; Sonuga-Barke, Edmund; Stringaris, Argyris; Taylor, Eric; Anney, Richard; Ebstein, Richard P.; Gill, Michael; Miranda, Ana; Mulas, Fernando; Oades, Robert D.; Roeyers, Herbert; Rothenberger, Aribert; Steinhausen, Hans-Christoph; Faraone, Stephen V.

2010-01-01

Background: The goal of this study was to investigate the occurrence, severity and clinical correlates of emotional lability (EL) in children with attention deficit/hyperactivity disorder (ADHD), and to examine factors contributing to EL and familiality of EL in youth with ADHD. Methods: One thousand, one hundred and eighty-six children with ADHD…

Cutting method for structural component into block like shape, and device used for cutting

International Nuclear Information System (INIS)

Nakazawa, Koichi; Ito, Akira; Tateiwa, Masaaki.

1995-01-01

Two grooves each of a predetermined depth are formed along a surface of a structural component, and a portion between the two grooves is cut in the direction of the depth from the surface of the structural component by using a cutting wire of a wire saw device. Then, the cutting wire is moved in the extending direction of the grooves while optionally changing the position in the direction of the depth to conduct cutting for the back face. Further, the cutting wire is moved in the direction of the depth of the groove toward the surface, to cut a portion between the two grooves. The wire saw device comprises a wire saw main body movable along the surface of the structural component, a pair of wire guide portions extending in the direction of the depth, guide pooleys capable of guiding the cutting wire guides revolvably and rotatably disposed at the top end, and an endless annular cutting wire extending between the wire guide portions. Thus, it is possible to continuously cut out blocks set to optional size and thickness. In addition, remote cutting is possible with no requirement for an operator to access to the vicinity of radioactivated portions. (N.H.)

An FMS Dynamic Production Scheduling Algorithm Considering Cutting Tool Failure and Cutting Tool Life

International Nuclear Information System (INIS)

Setiawan, A; Wangsaputra, R; Halim, A H; Martawirya, Y Y

2016-01-01

This paper deals with Flexible Manufacturing System (FMS) production rescheduling due to unavailability of cutting tools caused either of cutting tool failure or life time limit. The FMS consists of parallel identical machines integrated with an automatic material handling system and it runs fully automatically. Each machine has a same cutting tool configuration that consists of different geometrical cutting tool types on each tool magazine. The job usually takes two stages. Each stage has sequential operations allocated to machines considering the cutting tool life. In the real situation, the cutting tool can fail before the cutting tool life is reached. The objective in this paper is to develop a dynamic scheduling algorithm when a cutting tool is broken during unmanned and a rescheduling needed. The algorithm consists of four steps. The first step is generating initial schedule, the second step is determination the cutting tool failure time, the third step is determination of system status at cutting tool failure time and the fourth step is the rescheduling for unfinished jobs. The approaches to solve the problem are complete-reactive scheduling and robust-proactive scheduling. The new schedules result differences starting time and completion time of each operations from the initial schedule. (paper)

Evaluation of Soil Quality Using Labile Organic Carbon and Carbon Management Indices in Agricultural Lands of Neyriz, Fars Province

Directory of Open Access Journals (Sweden)

Anahid Salmanpour

2017-02-01

Full Text Available Introduction: Soil organic matter is considered as an indicator of soil quality, because of its role on the stability of soil structure, water holding capacity, microbial activity, storage and release of nutrients. Although changes and trends of organic matter are assessed on the basis of organic carbon, it responds slowly to changes of soil management. Therefore, identifying sensitive components of organic carbon such as carbon labile lead to better understanding of the effect of land use change and soil management on soil quality. The main components of sustainable agriculture in arid and semi-arid regions are the amount of water; and soil and water salinity. Water deficit and irrigation with saline water are important limiting factors for cropping and result in adverse effects on soil properties and soil quality. Soil carbon changes is a function of addition of plant debris and removal of it from soil by its decomposition. If the amount of organic carbon significantly reduced due to the degradation of the soil physical and chemical properties and soil quality, agricultural production will face serious problems. To this end, this study was done to evaluate soil quality using soil labile carbon and soil carbon management indices in some agricultural lands of Neyriz area, Fars province, Iran. Materials and Methods: Five fields were selected in two regions, Dehfazel and Tal-e-mahtabi, consisted of irrigated wheat and barley with different amount of irrigation water and water salinity levels. Three farms were located in Dehfazel and two farms in Tal-e-Mahtabi region. In each farm, three points were randomly selected and soil samples were collected from 0-40 cm of the surface layer. Plant samples were taken from a 1x1 square meter and grain crop yield was calculated per hectare. Water samples were obtained in each region from the wells at the last irrigation. Physical and chemical characteristics of the soil and water samples were determined. Soil

Advanced cutting techniques: laser and fissuration cutting

International Nuclear Information System (INIS)

Migliorati, B.; Gay, P.

1984-01-01

Experimental tests have been performed using CO 2 laser with output power 1 to 15 kW to evaluate the effect of varying the following parameters: material (carbon steel Fe 42 C, stainless steel AISI 304, concrete), laser power, beam characteristics, work piece velocity, gas type and distribution on the laser interaction zone. In the case of concrete, drilling depths of 80 mm were obtained in a few seconds using a 10 kW laser beam. Moreover pieces of 160 mm were cut at 0.01 meters per minute. Results with carbon steel indicated maximum thicknesses of 110 mm, cut at 0.01 meters per minute with 10 kW, depths about 20% lower were obtained with the AISI 304 stainless steel. A parallel investigation was aimed at characterizing particulate emission during the laser cutting process. At the end of the research it was possible to elaborate a preliminary proposal concerning a laser based dismantling system for the application to a typical Nuclear Power Station. (author)

Cutting agents for special metals

International Nuclear Information System (INIS)

Sugito, Seiji; Sakakibara, Fumi

1979-01-01

The quantity of use of special metals has increased year after year in the Plasma Research Institute, Nagoya University, with the development of researches on plasma and nuclear fusion. Most of these special metals are hard to cut, and in order to secure the surface smoothness and dimensional accuracy, considerable efforts are required. The method of experiment is as follows: cutting agents salt water and acetone, rape-seed oil, sulfide and chloride oil and water soluble cutting oil W grade 3; metals to be cut niobium, molybdenum, tantalum, titanium and tungsten; cutting conditions cutting speed 4.7 to 90 m/min, feed 0.07 to 0.2 mm/rev, depth of cut 0.1 to 0.4 mm, tool cemented carbide bit. Chemicals such as tetrachloromethane and trichloroethane give excellent cutting performance, but the toxicity is intense and the stimulative odor exists, accordingly they are hard to use practically. Cutting was easier when the salt water added with acetone was used than the case of rape-seed oil, but salt water is corrosive. Recently, the machining of molybdenum has been often carried out, and the water soluble cutting oil was the best. It is also good for cutting stainless steel, and its lubricating property is improved by adding some additives such as sulfur, chlorine, phosphorus and molybdenum disulfide. However after cutting with it, washing is required. (Kako, I.)

Performance Testing of Cutting Fluids

DEFF Research Database (Denmark)

Belluco, Walter

The importance of cutting fluid performance testing has increased with documentation requirements of new cutting fluid formulations based on more sustainable products, as well as cutting with minimum quantity of lubrication and dry cutting. Two sub-problems have to be solved: i) which machining...... tests feature repeatability, reproducibility and sensitivity to cutting fluids, and ii) to what extent results of one test ensure relevance to a wider set of machining situations. The present work is aimed at assessing the range of validity of the different testing methods, investigating correlation...... within the whole range of operations, materials, cutting fluids, operating conditions, etc. Cutting fluid performance was evaluated in turning, drilling, reaming and tapping, and with respect to tool life, cutting forces, chip formation and product quality (dimensional accuracy and surface integrity...

EFECTO DE LA DENSIDAD DE PLANTACIÓN EN LA RENTABILIDAD DE PLANTACIONES DE Eucalyptus globulus

Directory of Open Access Journals (Sweden)

Emilio Guerra-Bugueño

2014-01-01

Full Text Available El estudio evaluó, económicamente, la respuesta de densidades de plantación y marcos de espaciamiento de Eucalyptus globulus establecido con fines pulpables. La técnica de Montecarlo se usó para examinar el efecto de las variaciones de precios y la tasa de descuento sobre la rentabilidad. El ensayo fue realizado en el Valle Central de la IX Región de Chile. Los tratamientos fueron: 1,000 árboles·ha-1(T1; 1,428 árboles·ha-1 (T2; 1,667 árboles·ha-1 (T3 y 2,000 árboles·ha-1 (T4. El volumen de producción de cada tratamiento se midió a la edad de cosecha (10 años y posteriormente se realizó un análisis financiero, para obtener la rentabilidad (valor actual neto [VAN], valor económico del suelo [VES] y tasa interna de retorno [TIR]. Los mayores valores de VAN se obtuvieron con el T1 (US$ 330·ha-1 y T4 (US$ 322·ha-1. Los pronósticos obtenidos para el VAN de T1 mostraron una probabilidad de ocurrencia de 73 %, resultando ser la opción menos riesgosa para la inversión. Los mayores rendimientos volumétricos (T4 y T3 no propician las mayores rentabilidades, pues el incremento de la densidad de plantación aumenta los costos por unidad de planta con relación al manejo de suelos, control de malezas y fertilización.

Characterization of labile organic carbon in coastal wetland soils of the Mississippi River deltaic plain: Relationships to carbon functionalities

Energy Technology Data Exchange (ETDEWEB)

Dodla, Syam K. [School of Plant, Environmental and Soil Sciences, Louisiana State Univ. Agricultural Center, Baton Rouge, LA 70803 (United States); Wang, Jim J., E-mail: jjwang@agcenter.lsu.edu [School of Plant, Environmental and Soil Sciences, Louisiana State Univ. Agricultural Center, Baton Rouge, LA 70803 (United States); DeLaune, Ronald D. [Department of Oceanography and Coastal Sciences, School of the Coast and Environment, Louisiana State University, Baton Rouge, LA 70803 (United States)

2012-10-01

Adequate characterization of labile organic carbon (LOC) is essential to the understanding of C cycling in soil. There has been very little evaluation about the nature of LOC characterizations in coastal wetlands, where soils are constantly influenced by different redox fluctuations and salt water intrusions. In this study, we characterized and compared LOC fractions in coastal wetland soils of the Mississippi River deltaic plain using four different methods including 1) aerobically mineralizable C (AMC), 2) cold water extractable C (CWEC), 3) hot water extractable C (HWEC), and 4) salt extractable C (SEC), as well as acid hydrolysable C (AHC) which includes both labile and slowly degradable organic C. Molecular organic C functional groups of these wetland soils were characterized by {sup 13}C solid-state nuclear magnetic resonance (NMR). The LOC and AHC increased with soil organic C (SOC) regardless of wetland soil type. The LOC estimates by four different methods were positively and significantly linearly related to each other (R{sup 2} = 0.62-0.84) and with AHC (R{sup 2} = 0.47-0.71). The various LOC fractions accounted for {<=} 4.3% of SOC whereas AHC fraction represented 16-49% of SOC. AMC was influenced positively by O/N-alkyl and carboxyl C but negatively by alkyl C, whereas CWEC and SEC fractions were influenced only positively by carboxyl C but negatively by alkyl C in SOC. On the other hand, HWEC fraction was found to be only influenced positively by carbonyl C, and AHC positively by O/N-alkyl and alkyl C but negatively by aromatic C groups in SOC. Overall these relations suggested different contributions of various molecular organic C moieties to LOC in these wetlands from those often found for upland soils. The presence of more than 50% non-acid hydrolysable C suggested the dominance of relatively stable SOC pool that would be sequestered in these Mississippi River deltaic plain coastal wetland soils. The results have important implications to the

Female genital cutting.

Science.gov (United States)

Perron, Liette; Senikas, Vyta; Burnett, Margaret; Davis, Victoria

2013-11-01

To strengthen the national framework for care of adolescents and women affected by female genital cutting (FGC) in Canada by providing health care professionals with: (1) information intended to strengthen their knowledge and understanding of the practice; (2) directions with regard to the legal issues related to the practice; (3) clinical guidelines for the management of obstetric and gynaecological care, including FGC related complications; and (4) guidance on the provision of culturally competent care to adolescents and women with FGC. Published literature was retrieved through searches of PubMed, CINAHL, and The Cochrane Library in September 2010 using appropriate controlled vocabulary (e.g., Circumcision, Female) and keywords (e.g., female genital mutilation, clitoridectomy, infibulation). We also searched Social Science Abstracts, Sociological Abstracts, Gender Studies Database, and ProQuest Dissertations and Theses in 2010 and 2011. There were no date or language restrictions. Searches were updated on a regular basis and incorporated in the guideline to December 2011. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table 1). Summary Statements 1. Female genital cutting is internationally recognized as a harmful practice and a violation of girls' and women's rights to life, physical integrity, and health. (II-3) 2. The immediate and long-term health risks and complications of female genital cutting can be serious and life threatening. (II-3) 3. Female genital cutting continues to be practised in many countries, particularly in sub-Saharan Africa, Egypt, and Sudan. (II-3) 4. Global migration

EFEITO RESIDUAL DE INSETICIDAS NATURAIS NO CONTROLE DE SITOPHILUS ZEAMAIS MOTS. EM MILHO ARMAZENADO

Directory of Open Access Journals (Sweden)

Rodrigo Leandro Braga de Castro Coitinho

2006-01-01

Full Text Available The residual effect of natural insecticides was evaluated on adults of Sitophilus zeamais Mots. (Coleoptera: Curculionidae on stored corn grains. Clove (Syzygium aromaticum L., white pepper (Piper nigrum L., neem (Azadirachta indica A. Juss and silica dioxide powders were tested as well as neem, eucalyptus (Eucaliptus globulus Labill and Eucaliptus citriodora Hook., eugenol, andiroba (Carapa guianensis Aubl., rosemary (Lippia gracillis HBK., cedar (Cedrela fissilis Vell. and pequi (Caryocar brasiliense Camb. oils. Powders were tested at concentration of 1kg/t in 50g-corn-plot and the oils at dosage of 50¿L in 20g-corn-plot. The plots infestation was accomplished using 20 and 8 adults (males and females of S. zeamais being 0 to 15 days old, respectively, in the experiments with powders and oils. Silica dioxide caused 46.7, 38.3 and 37.5% of mortality, respectively, in the initial (soon after the treatment with the powders or oils and at 60 and 120 days of storage periods, but the mortality induced by the other powders was inexpressive. In the three studied storage periods, silica dioxide was the more efficient in reducing adults emergency. At the initial storage period, all the oils caused mortality above 79%, however, after 60 and 120 days, mortality was lower than 2.5%. The adult emergency increased as stored period increased, although at 120 days the best performance was obtained using neem, followed by andiroba, cedar, rosemary and E. globulus oils.

ATIVIDADE INSETICIDA DE ÓLEOS VEGETAIS SOBRE Sitophilus zeamais MOTS. (COLEOPTERA: CURCULIONIDAE EM MILHO ARMAZENADO

Directory of Open Access Journals (Sweden)

Rodrigo Leandro Braga de Castro Coitinho

2006-01-01

Full Text Available Oils of andiroba (Carapa guianensis Aubl., copaiba (Copaifera sp., Eucaliptus globulus Labill. and Eucaliptus citriodora Hook., neem (Azadirachta indica A. Juss, eugenol, souari nut (Caryocar brasiliense Camb., rosemary (Lippia gracillis HBK., and cedar (Cedrela fissilis Vell. were evaluated in adults of Sitophilus zeamais Mots. (Coleoptera: Curculionidae. In the non-choice test, 20 g of corn grains per plot were treated with 50¿L of each oil and homogenized for two minutes. The plot was infested with eight 0 to 15 days-old S. zeamais adults. The E. globulus, eugenol, rosemary, and neem oils caused 100% mortality in S. zeamais adults. Except for copaiba, all oils caused mortality above 87% and the reduction in emergence of 100%. In the free-choice tests, arenas consisting of two plastic containers symmetrically interconnected to a central box by two plastic tubes were used. Twenty grams of non-treated corn (control were placed in one of the boxes and the same amount of grain treated with 50¿L of each oil comprised the other treatment. Sixteen non-sexed S. zeamais adults (0-15 days old were released in the central box. The rosemary, E. citriodora, eugenol and copaiba oils were the most repellent for S. zeamais adults, with repellence percentage varying from 97.3 to 87.7. Rosemary, andiroba, neem, and cedar reduced S. zeamais emergence in 100%, while the reduction caused by the other oils ranged from 72.7 to 97.9%.

Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal cutting methods

International Nuclear Information System (INIS)

Bienia, H.; Klotz, B.

2008-01-01

This article describes 3 thermal cutting technologies that are effectively used in nuclear decommissioning projects: the autonomous flame cutting, the plasma arc cutting and the contact arc metal cutting. The autonomous flame cutting technology is based on a high pressure oxygen jet oxidizing the material in a small kerf. Not all metal types are appropriate for this technology. The plasma arc cutting, in contrast to the previous technology, uses an electronically induced plasma arc to melt a kerf in the material. Inside the plasma arc temperatures up to 30.000 K exist, so in theory, this temperature is sufficient to cut all materials. Contact arc metal cutting is a new thermal cutting technology for under-water cutting works. Here, a carbon blade cuts the components. An electric arc between the cutting blade and component melts a kerf into the material easing the cutting. This technology allows the cutting of complex structures with hollows. The applications in nuclear facility dismantling of these 3 cutting technologies and their limits are reported and their requirements (staff, investment) listed in a table. (A.C.)

Water stress and recovery in the performance of two Eucalyptus globulus clones: physiological and biochemical profiles.

Science.gov (United States)

Correia, Barbara; Pintó-Marijuan, Marta; Neves, Lucinda; Brossa, Ricard; Dias, Maria Celeste; Costa, Armando; Castro, Bruno B; Araújo, Clara; Santos, Conceição; Chaves, Maria Manuela; Pinto, Glória

2014-04-01

Eucalyptus plantations are among the most productive forest stands in Portugal and Spain, being mostly used for pulp production and, more recently, as an energy crop. However, the region's Mediterranean climate, with characteristic severe summer drought, negatively affects eucalypt growth and increases mortality. Although the physiological response to water shortage is well characterized for this species, evidence about the plants' recovery ability remains scarce. In order to assess the physiological and biochemical response of Eucalyptus globulus during the recovery phase, two genotypes (AL-18 and AL-10) were submitted to a 3-week water stress period at two different intensities (18 and 25% of field capacity), followed by 1 week of rewatering. Recovery was assessed 1 day and 1 week after rehydration. Drought reduced height, biomass, water potential, NPQ and gas exchange in both genotypes. Contrarily, the levels of pigments, chlorophyll fluorescence parameters (F(v) /F(m) and (φPSII)), MDA and ABA increased. During recovery, the physiological and biochemical profile of stressed plants showed a similar trend: they experienced reversion of altered traits (MDA, ABA, E, g(s), pigments), while other parameters did not recover ((φPSII), NPQ). Furthermore, an overcompensation of CO(2) assimilation was achieved 1 week after rehydration, which was accompanied by greater growth and re-establishment of oxidative balance. Both genotypes were tolerant to the tested conditions, although clonal differences were found. AL-10 was more productive and showed a more rapid and dynamic response to rehydration (namely in carotenoid content, (φPSII) and NPQ) compared to clone AL-18. © 2013 Scandinavian Plant Physiology Society.

Extension without Cut

OpenAIRE

Straßburger , Lutz

2012-01-01

International audience; In proof theory one distinguishes sequent proofs with cut and cut-free sequent proofs, while for proof complexity one distinguishes Frege-systems and extended Frege-systems. In this paper we show how deep inference can provide a uniform treatment for both classifications, such that we can define cut-free systems with extension, which is neither possible with Frege-systems, nor with the sequent calculus. We show that the propositional pigeon-hole principle admits polyno...

Overland flow generation processes in sub-humid Mediterranean forest stands

Science.gov (United States)

Ferreira, A. J. D.; Ferreira, C. S. S.; Coelho, C. O. A.; Walsh, R. P. D.; Shakesby, R. A.

2012-04-01

Forest soils in north and central Portugal have suffered and continue to suffer major structural changes as a result of forest management techniques, such as clear-felling and as a result of wildfire and rip-ploughing, which is carried out to prepare the ground for planting tree seedlings. In soils that have undergone these changes, the characteristics tend to be different for coniferous plantations, where the root system tends to die when the trees are cut following fire and subsequently may be consumed by fire to form a macropore network, and other types of tree plantations where the root system remains alive and allows regrowth from the sawn tree stumps. Overland flow thresholds decrease sharply as a result of rip-ploughing and forest fires and increase following clear-felling. The time taken for trees to reach maturity after wildfire differs markedly betwen the two main species (Pinus pinaster Aiton and Eucalyptus globulus Labill.) stands. In this paper, overland flow is considered in relation to rainfall, throughfall and throughflow, both in terms of hydrology and hydrochemistry in an attempt to understand overland flow generation mechanisms for a variety of forest land uses (mature pine and eucalyptus, pine seedling regrowth and eucalyptus regrowth from tree stumps, eucalyptus plantations and burned pine). Overland flow generation processes change sharply, even within a single rainfall event, as reflected in the soil hydrological processes and the hydrochemical fingerprints. These effects result from the different contact times for water and soil, which cause differences in the absorption and exhudation processes for the two species

Quantitative chemical exchange saturation transfer (qCEST) MRI - omega plot analysis of RF-spillover-corrected inverse CEST ratio asymmetry for simultaneous determination of labile proton ratio and exchange rate.

Science.gov (United States)

Wu, Renhua; Xiao, Gang; Zhou, Iris Yuwen; Ran, Chongzhao; Sun, Phillip Zhe

2015-03-01

Chemical exchange saturation transfer (CEST) MRI is sensitive to labile proton concentration and exchange rate, thus allowing measurement of dilute CEST agent and microenvironmental properties. However, CEST measurement depends not only on the CEST agent properties but also on the experimental conditions. Quantitative CEST (qCEST) analysis has been proposed to address the limitation of the commonly used simplistic CEST-weighted calculation. Recent research has shown that the concomitant direct RF saturation (spillover) effect can be corrected using an inverse CEST ratio calculation. We postulated that a simplified qCEST analysis is feasible with omega plot analysis of the inverse CEST asymmetry calculation. Specifically, simulations showed that the numerically derived labile proton ratio and exchange rate were in good agreement with input values. In addition, the qCEST analysis was confirmed experimentally in a phantom with concurrent variation in CEST agent concentration and pH. Also, we demonstrated that the derived labile proton ratio increased linearly with creatine concentration (P analysis can simultaneously determine labile proton ratio and exchange rate in a relatively complex in vitro CEST system. Copyright © 2015 John Wiley & Sons, Ltd.

Aerodynamic Interactions During Laser Cutting

Science.gov (United States)

Fieret, J.; Terry, M. J.; Ward, B. A.

1986-11-01

Most laser cutting systems utilise a gas jet to remove molten or vaporised material from the kerf. The speed, economy and quality of the cut can be strongly dependent on the aerodynamic conditions created by the nozzle, workpiece proximity and kerf shape. Adverse conditions can be established that may lead to an unwelcome lack of reproducibility of cut quality. Relatively low gas nozzle pressures can result in supersonic flow in the jet with its associated shock fronts. When the nozzle is placed at conventional distances (1-2mm) above the workpiece, the force exerted by the gas on the workpiece and the cut products (the cutting pressure) can be significantly less than the nozzle pressure. Higher cutting pressures can be achieved by increasing the height of the nozzle above the workpiece, to a more damage resistant zone, provided that the shock structure of the jet is taken into account. Conventional conical nozzles with circular exits can be operated with conditions that will result in cutting pressures up to 3 Bar (g) in the more distant zone. At higher pressures in circular tipped nozzles the cutting pressure in this zone decays to inadequate levels. Investigations of a large number of non-circular nozzle tip shapes have resulted in the selection of a few specific shapes that can provide cutting pressures in excess of 6 Bar(g) at distances of 4 to 7mm from the nozzle tip. Since there is a strong correlation between cutting pressure and the speed and quality of laser cutting, the paper describes the aerodynamic requirements for achieving the above effects and reports the cutting results arising from the different nozzle designs and conditions. The results of the work of other investigators, who report anomalous laser cutting results, will be examined and reviewed in the light of the above work.

Reactivity of syringyl and guaiacyl lignin units and delignification kinetics in the kraft pulping of Eucalyptus globulus wood using Py-GC-MS/FID.

Science.gov (United States)

Lourenço, Ana; Gominho, Jorge; Marques, António Velez; Pereira, Helena

2012-11-01

Eucalyptus globulus sapwood and heartwood showed no differences in lignin content (23.0% vs. 23.7%) and composition: syringyl-lignin (17.9% vs. 18.0%) and guaiacyl-lignin (4.8% vs. 5.2%). Delignification kinetics of S- and G-units in heartwood and sapwood was investigated by Py-GC-MS/FID at 130, 150 and 170°C and modeled as double first-order reactions. Reactivity differences between S and G-units were small during the main pulping phase and the higher reactivity of S over G units was better expressed in the later pulping stage. The residual lignin composition in pulps was different from wood or from samples in the initial delignification stages, with more G and H-units. S/G ratio ranged from 3 to 4.5 when pulp residual lignin was higher than 10%, decreasing rapidly to less than 1. The S/H was initially around 20 (until 15% residual lignin), decreasing to 4 when residual lignin was about 3%. Copyright © 2012 Elsevier Ltd. All rights reserved.

Hemodynamic changes in systolic and diastolic function during isoproterenol challenge predicts symptomatic response to myectomy in hypertrophic cardiomyopathy with labile obstruction.

Science.gov (United States)

Prasad, Megha; Geske, Jeffrey B; Sorajja, Paul; Ommen, Steve R; Schaff, Hartzell V; Gersh, Bernard J; Nishimura, Rick A

2016-11-15

We aimed to assess the utility of changes in systolic and diastolic function by isoproterenol challenge in predicting symptom resolution post-myectomy in selected patients with hypertrophic cardiomyopathy (HCM) and labile obstruction. In a subset of symptomatic HCM patients without resting/provocable obstruction on noninvasive assessment, isoproterenol challenge during hemodynamic catheterization may elicit labile left ventricular outflow tract (LVOT) obstruction, and demonstrate the effect of obstruction on diastolic function. These changes may determine whether patients achieve complete symptom resolution post-myectomy. Between February 2003 and April 2009, 18 symptomatic HCM patients without LVOT obstruction on noninvasive testing underwent isoproterenol provocation and septal myectomy due to presence of provocable gradient and were followed for 4 (IQR 3-7) years. Thirteen (72.2%) had complete symptom resolution, while 5 (27.8%) had improved, but persistent symptoms. Those with provoked gradient >100 mm Hg or increase in left atrial pressure (LAP) with isoproterenol had symptom resolution. Symptomatic HCM patients without LVOT gradient on noninvasive testing may demonstrate labile obstruction with isoproterenol. With isoproterenol, patients with high LVOT gradient or increase in LAP concomitant with an increase in gradient achieved complete symptom resolution post-myectomy. Thus, improved diastolic filling as well as outflow gradient production in patients with HCM may predict symptom response to myectomy. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Effects of composition of labile organic matter on biogenic production of methane in the coastal sediments of the Arabian Sea.

Science.gov (United States)

Gonsalves, Maria-Judith; Fernandes, Christabelle E G; Fernandes, Sheryl Oliveira; Kirchman, David L; Bharathi, P A Loka

2011-11-01

Coastal regions are potential zones for production of methane which could be governed by ecological/environmental differences or even sediment properties of a niche. In order to test the hypothesis that methanogenesis in most marine sediments could be driven more by proteins than by carbohydrates and lipid content of labile organic matter (LOM), incubation experiments were carried out with sediments from different environmental niches to measure methane production. The methane production rates were examined in relationship to the sediment biochemistry, i.e., carbohydrates, proteins, and lipids. The gas production measured by head space method ranged from 216 ng g( -1) day( -1) in the mangrove sediments to 3.1 μg g( -1) day( -1) in the shallow Arabian Sea. LOM ranged from 1.56 to 2.85 mg g( -1) in the shallow Arabian Sea, from 3.35 to 5.43 mg g( -1) in the mangrove estuary, and from 0.66 to 0.70 mg g( -1) in the sandy sediments with proteins contributing maximum to the LOM pool. Proteins influenced methane production in the clayey sediments of shallow depths of the Arabian Sea (r = 0.933, p methane production. The gas production was more pronounced in shallow and surface sediments and it decreased with depth apparently governed by the decrease in lability index. Thus, the lability index and protein content are important factors that determine methane production rates in these coastal ecosystems.

Cutting system for burnable poison rod

International Nuclear Information System (INIS)

Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

1989-01-01

Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

Long-term addition of fertilizer, labile carbon, and fungicide alters the biomass of plant functional groups in a subarctic-alpine community

DEFF Research Database (Denmark)

Haugwitz-Hardenberg-Reventlow, M S; Michelsen, A.

2011-01-01

experiment on a subarctic-alpine fellfield dominated by woody evergreen shrubs, bryophytes, and lichens. To manipulate nutrient availability additions of NPK fertilizer, labile C, and fungicide (benomyl) were done in a fully factorial design, replicated in six blocks. The treatments were run for 10 years...... vascular plant groups. Also, limitation of soil nutrient availability caused by labile C addition decreased the relative proportion of green shoots in evergreen shrubs, although these were expected to cope better with the nutrient limitation than the opportunistic graminoids, which, by contrast, were...... unaffected. Reduced fungal biomass due to benomyl addition was accompanied by increased evergreen shrub and clubmoss biomass. Taken together, the effects of treatments were most pronounced 16 years after initiation of the experiment, but despite changes in biomass the overall plant community composition...

Theoretical Models for Orthogonal Cutting

DEFF Research Database (Denmark)

De Chiffre, Leonardo

This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”......This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”...

Laser circular cutting of Kevlar sheets: Analysis of thermal stress filed and assessment of cutting geometry

Science.gov (United States)

Yilbas, B. S.; Akhtar, S. S.; Karatas, C.

2017-11-01

A Kevlar laminate has negative thermal expansion coefficient, which makes it difficult to machine at room temperaures using the conventional cutting tools. Contararily, laser machining of a Kevlar laminate provides advantages over the conventional methods because of the non-mechanical contact between the cutting tool and the workpiece. In the present study, laser circular cutting of Kevlar laminate is considered. The experiment is carried out to examine and evaluate the cutting sections. Temperature and stress fields formed in the cutting section are simulated in line with the experimental study. The influence of hole diameters on temperature and stress fields are investigated incorporating two different hole diameters. It is found that the Kevlar laminate cutting section is free from large size asperities such as large scale sideways burnings and attachemnt of charred residues. The maximum temperature along the cutting circumference remains higher for the large diameter hole than that of the small diameter hole. Temperature decay is sharp around the cutting section in the region where the cutting terminates. This, in turn, results in high temperature gradients and the thermal strain in the cutting region. von Mises stress remains high in the region where temperature gradients are high. von Mises stress follows similar to the trend of temperature decay around the cutting edges.

A study of estimating cutting depth for multi-pass nanoscale cutting by using atomic force microscopy

International Nuclear Information System (INIS)

Lin, Zone-Ching; Hsu, Ying-Chih

2012-01-01

This paper studies two models for estimating cutting depth of multi-pass nanoscale cutting by using an atomic force microscopy (AFM) probe. One estimates cutting depth for multi-pass nanoscale cutting by using regression equations of nanoscale contact pressure factor (NCP factor) while the other uses equation of specific down force energy (SDFE). This paper proposes taking a diamond-coated probe of AFM as the cutting tool to carry out multi-pass nanoscale cutting experiments on the surface of sapphire substrate. In the process of experimentation, different down forces are set, and the probe shape of AFM is known, then using each down force to multi-pass cutting the sapphire substrate. From the measured experimental data of a central cutting depth of the machining groove by AFM, this paper calculates the specific down force energy of each down force. The experiment results reveal that the specific down force energy of each case of multi-pass nanoscale cutting for different down forces under a probe of AFM is close to a constant value. This paper also compares the nanoscale cutting results from estimating cutting depths for each pass of multi-pass among the experimental results and the calculating results obtained by the two theories models. It is found that the model of specific down force energy can calculate cutting depths for each nanoscale cutting pass by one equation. It is easier to use than the multi-regression equations of the nanoscale contact pressure factor. Besides, the estimations of cutting depth results obtained by the model of specific down force energy are closer to that of the experiment results. It shows that the proposed specific down force energy model in this paper is an acceptable model.

Relationship between the lability of sediment-bound Cd and its bioaccumulation in edible oyster

Digital Repository Service at National Institute of Oceanography (India)

Chakraborty, P.; Ramteke, D.; Chakraborty, S.; Chennuri, K.; Bardhan, P.

unaffected by changes in Eh of the medium (Zia-ur-Rehman et al., 2015; Pascaud et al., 2015). Complexations of Cd with carbonate restrict mobility of Cd in carbonate-rich sediment and soil (Wu et al., 2015; Wang et al., 2015). Sekaly et al (1999) have... contribution number XXXX. References Almås, Å. R., McBride, M. B., & Singh, B. R. (2000). Solubility and lability of cadmium and zinc in two soils treated with organic matter. Soil Science, 165(3), 250-259. Broten, D. (1998). BC oysters face cadmium...

Relationship between the lability of sediment-bound Cd and its bioaccumulation in edible oyster.

Digital Repository Service at National Institute of Oceanography (India)

Chakraborty, P.; Ramteke, D.; Chakraborty, S.; Chennuri, K.; Bardhan, P.

unaffected by changes in Eh of the medium (Zia-ur-Rehman et al., 2015; Pascaud et al., 2015). Complexations of Cd with carbonate restrict mobility of Cd in carbonate-rich sediment and soil (Wu et al., 2015; Wang et al., 2015). Sekaly et al (1999) have... contribution number XXXX. References Almås, Å. R., McBride, M. B., & Singh, B. R. (2000). Solubility and lability of cadmium and zinc in two soils treated with organic matter. Soil Science, 165(3), 250-259. Broten, D. (1998). BC oysters face cadmium...

Consumer evaluation of palatability characteristics of a beef value-added cut compared to common retail cuts.

Science.gov (United States)

Lepper-Blilie, A N; Berg, E P; Germolus, A J; Buchanan, D S; Berg, P T

2014-01-01

The objectives of this study were to educate consumers about value-added beef cuts and evaluate their palatability responses of a value cut and three traditional cuts. Three hundred and twenty-two individuals participated in the beef value cut education seminar series presented by trained beef industry educators. Seminar participants evaluated tenderness, juiciness, flavor, and overall like of four samples, bottom round, top sirloin, ribeye, and a value cut (Delmonico or Denver), on a 9-point scale. The ribeye and the value cut were found to be similar in all four attributes and differed from the top sirloin and bottom round. Correlations and regression analysis found that flavor was the largest influencing factor for overall like for the ribeye, value cut, and top sirloin. The value cut is comparable to the ribeye and can be a less expensive replacement. © 2013.

Significance of Isotopically Labile Organic Hydrogen in Thermal Maturation of Organic Matter

Energy Technology Data Exchange (ETDEWEB)

Arndt Schimmelmann; Maria Mastalerz

2010-03-30

Isotopically labile organic hydrogen in fossil fuels occupies chemical positions that participate in isotopic exchange and in chemical reactions during thermal maturation from kerogen to bitumen, oil and gas. Carbon-bound organic hydrogen is isotopically far less exchangeable than hydrogen bound to nitrogen, oxygen, or sulfur. We explore why organic hydrogen isotope ratios express a relationship with organic nitrogen isotope ratios in kerogen at low to moderate maturity. We develop and apply new techniques to utilize organic D/H ratios in organic matter fractions and on a molecular level as tools for exploration for fossil fuels and for paleoenvironmental research. The scope of our samples includes naturally and artificially matured substrates, such as coal, shale, oil and gas.

Flux cutting in superconductors

International Nuclear Information System (INIS)

Campbell, A M

2011-01-01

This paper describes experiments and theories of flux cutting in superconductors. The use of the flux line picture in free space is discussed. In superconductors cutting can either be by means of flux at an angle to other layers of flux, as in longitudinal current experiments, or due to shearing of the vortex lattice as in grain boundaries in YBCO. Experiments on longitudinal currents can be interpreted in terms of flux rings penetrating axial lines. More physical models of flux cutting are discussed but all predict much larger flux cutting forces than are observed. Also, cutting is occurring at angles between vortices of about one millidegree which is hard to explain. The double critical state model and its developments are discussed in relation to experiments on crossed and rotating fields. A new experiment suggested by Clem gives more direct information. It shows that an elliptical yield surface of the critical state works well, but none of the theoretical proposals for determining the direction of E are universally applicable. It appears that, as soon as any flux flow takes place, cutting also occurs. The conclusion is that new theories are required. (perspective)

Development of underwater laser cutting technology

International Nuclear Information System (INIS)

Sato, Seiichi; Inaba, Takanori; Inose, Koutarou; Matsumoto, Naoyuki; Sakakibara, Yuji

2015-01-01

In is desirable to use remote underwater device for the decommissioning work of highly radioactive components such as the nuclear internals from a view point of reducing the ranitidine exposure to the worker. Underwater laser cutting technology has advantages. First advantage in underwater laser cutting technology is that low reaction force during cutting, namely, remote operability is superior. Second point is that underwater laser cutting generates a little amount of secondary waste, because cutting kerf size is very small. Third point is that underwater laser cutting has low risk of the process delay, because device trouble is hard to happen. While underwater laser cutting has many advantages, the careful consideration in the safe treatment of the offgas which underwater laser cutting generates is necessary. This paper describes outline of underwater laser cutting technology developed by IHI Corporation (IHI) and that this technology is effective in various dismantling works in water. (author)

Forms and lability of phosphorus in algae and aquatic macrophytes characterized by solution 31P NMR coupled with enzymatic hydrolysis

Science.gov (United States)

Increased information on forms and lability of phosphorus (P) in aquatic macrophytes and algae is crucial for better understanding of P biogeochemical cycling in eutrophic lakes. In this work, solution 31P nuclear magnetic resonance (NMR) spectroscopy coupled with enzymatic hydrolysis (EH) was used ...

Cutting temperature measurement and material machinability

Directory of Open Access Journals (Sweden)

Nedić Bogdan P.

2014-01-01

Full Text Available Cutting temperature is very important parameter of cutting process. Around 90% of heat generated during cutting process is then away by sawdust, and the rest is transferred to the tool and workpiece. In this research cutting temperature was measured with artificial thermocouples and question of investigation of metal machinability from aspect of cutting temperature was analyzed. For investigation of material machinability during turning artificial thermocouple was placed just below the cutting top of insert, and for drilling thermocouples were placed through screw holes on the face surface. In this way was obtained simple, reliable, economic and accurate method for investigation of cutting machinability.

Stresses in ultrasonically assisted bone cutting

International Nuclear Information System (INIS)

Alam, K; Mitrofanov, A V; Silberschmidt, V V; Baeker, M

2009-01-01

Bone cutting is a frequently used procedure in the orthopaedic surgery. Modern cutting techniques, such as ultrasonic assisted drilling, enable surgeons to perform precision operations in facial and spinal surgeries. Advanced understanding of the mechanics of bone cutting assisted by ultrasonic vibration is required to minimise bone fractures and to optimise the technique performance. The paper presents results of finite element simulations on ultrasonic and conventional bone cutting analysing the effects of ultrasonic vibration on cutting forces and stress distribution. The developed model is used to study the effects of cutting and vibration parameters (e.g. amplitude and frequency) on the stress distributions in the cutting region.

Optimisation Of Cutting Parameters Of Composite Material Laser Cutting Process By Taguchi Method

Science.gov (United States)

Lokesh, S.; Niresh, J.; Neelakrishnan, S.; Rahul, S. P. Deepak

2018-03-01

The aim of this work is to develop a laser cutting process model that can predict the relationship between the process input parameters and resultant surface roughness, kerf width characteristics. The research conduct is based on the Design of Experiment (DOE) analysis. Response Surface Methodology (RSM) is used in this work. It is one of the most practical and most effective techniques to develop a process model. Even though RSM has been used for the optimization of the laser process, this research investigates laser cutting of materials like Composite wood (veneer)to be best circumstances of laser cutting using RSM process. The input parameters evaluated are focal length, power supply and cutting speed, the output responses being kerf width, surface roughness, temperature. To efficiently optimize and customize the kerf width and surface roughness characteristics, a machine laser cutting process model using Taguchi L9 orthogonal methodology was proposed.

Selection of Near Optimal Laser Cutting Parameters in CO2 Laser Cutting by the Taguchi Method

Directory of Open Access Journals (Sweden)

Miloš MADIĆ

2013-12-01

Full Text Available Identification of laser cutting conditions that are insensitive to parameter variations and noise is of great importance. This paper demonstrates the application of Taguchi method for optimization of surface roughness in CO2 laser cutting of stainless steel. The laser cutting experiment was planned and conducted according to the Taguchi’s experimental design using the L27 orthogonal array. Four laser cutting parameters such as laser power, cutting speed, assist gas pressure, and focus position were considered in the experiment. Using the analysis of means and analysis of variance, the significant laser cutting parameters were identified, and subsequently the optimal combination of laser cutting parameter levels was determined. The results showed that the cutting speed is the most significant parameter affecting the surface roughness whereas the influence of the assist gas pressure can be neglected. It was observed, however, that interaction effects have predominant influence over the main effects on the surface roughness.

How Can I Stop Cutting?

Science.gov (United States)

... Educators Search English Español How Can I Stop Cutting? KidsHealth / For Teens / How Can I Stop Cutting? ... in a soft, cozy blanket Substitutes for the Cutting Sensation You'll notice that all the tips ...

Rooting of stem cuttings of ixora

Directory of Open Access Journals (Sweden)

Aline De Souza Silva

2015-08-01

Full Text Available The ixora is ornamental plant widely used in landscaping. In order to maximize the propagation of cuts, we evaluated the concentrations of auxin (indolbutiric acid and the presence of leaves on the rooting in cuts of Ixora coccinea L. The experiment was conducted in randomized block design, in factorial design 3x4, with three types of cuts (without leaf, with two or four leaves, four concentrations of indolbutiric acid (0, 1000, 2000 and 4000 mg L-1, with four replications and 10 cuts in each experimental unit. After 53 days of implantation the experiment, evaluated the survival(%, rooting(%, sprouting(%, formation of callus(%, number, length and biomass of roots formed. The interaction of the type of cuts with concentrations of auxin was not significant for any of the variables analyzed. The survival of cuttings was not influenced by the treatments. Cuts with two or four leaves presented rooting and length of roots above the cuttings without leaves. The application of auxin does not substitute the presence of leaf in cuts of ixora in vegetative propagation. The vegetative propagation by cut of ixora can be made without application of auxin, and the leaves must be maintained in the cuttings.

Development of lathe tool dynamometer and finding cutting forces using negative and positive rake angle cutting tool

International Nuclear Information System (INIS)

Zeb, M.A.; Irfan, M.A.

2005-01-01

Most output parameters in machining, such as cutting forces, temperatures, strains and the work-hardening of the chip material, are directly related to the chip formation process. The characteristics of machining processes can be well understood if the forces and strains during chip formation are known. In this research a lathe tool dynamometer was used to measure cutting forces involved in machining of Steel 1045 and Aluminum 2219 T62. High Speed Steel (HSS), cutting tools with positive and negative rake angles were used. It was observed that more cutting forces are experienced by the cutting tool with positive rake angle as compared to the forces experienced by the cutting tool with negative rake angle. For steel 1045 the cutting forces using positive rake angle cutting tool were much higher. This suggested that for harder materials using a negative rake angle is more suitable for cutting. (author)

Investigation of Physical Phenomena and Cutting Efficiency for Laser Cutting on Anode for Li-Ion Batteries

Directory of Open Access Journals (Sweden)

Dongkyoung Lee

2018-02-01

Full Text Available Lithium-ion batteries have a higher energy density than other secondary batteries. Among the lithium-ion battery manufacturing process, electrode cutting is one of the most important processes since poor cut quality leads to performance degradation, separator protrusion, and local electric stress concentration. This may, eventually, lead to malfunction of lithium-ion batteries or explosion. The current mechanical cutting technology uses a contact process and this may lead to process instability. Furthermore, there are additional costs if the tools and cell design are changed. To solve these issues, laser cutting has been used. Conventional dependent parameters have limitations in investigating and explaining many physical phenomena during the laser cutting of electrodes. Therefore, this study proposes specific widths such as melting, top, and kerf width. Moreover, the relationship between laser parameters and multiphysical phenomena with the proposed widths are investigated. Five types of classification with regard to physical phenomena are presented and explained with SEM images. Cutting efficiency is estimated with the proposed widths. The proposed specific cutting widths, five types of geometrical classification, and cutting efficiency can be used as standardized parameters to evaluate the cutting quality.

CALCULATION OF LASER CUTTING COSTS

OpenAIRE

Bogdan Nedic; Milan Eric; Marijana Aleksijevic

2016-01-01

The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, compar...

Method of cutting radioactivated metal structures

International Nuclear Information System (INIS)

Takimoto, Yoshinori; Sakota, Kotaro; Hamamoto, Noboru; Harada, Keizo.

1985-01-01

Purpose: To improve the cutting performance to a level as comparable with that in air, as well as prevent the scattering of the radioactive materials upon cutting to the level as that in water cutting. Method: After igniting a gas cutting torch automatically, water spray by the local water sprayer is started by the actuation of a submerged pump, while a gas cutting manipulator is operated to cut the nuclear reactor pressure vessel. In this way, cutting exhaust gases resulted from the gas cutting torch are water-washed by the spray from the local water sprayer and falls within the nuclear rector pressure vessel in the form of water streams or droplets along the inner wall surface of the pressure vessel. Further, water is fed again to the local water sprayer by the submerged pump. (Kawakami, Y.)

Laser Cutting of Thin Nickel Bellows

Science.gov (United States)

Butler, C. L.

1986-01-01

Laser cutting technique produces narrow, precise, fast, and repeatable cuts in thin nickel-allow bellows material. Laser cutting operation uses intense focused beam to melt material and assisting gas to force melted material through part thickness, creating void. When part rotated or moved longitudinally, melting and material removal continuous and creates narrow, fast, precise, and repeatable cut. Technique used to produce cuts of specified depths less than material thickness. Avoids distortion, dents, and nicks produced in delicate materials during lathe trimming operations, which require high cutting-tool pressure and holding-fixture forces.

Experimental improvement of the technology of cutting of high-pressure hoses with metal braid on hand cutting machine

OpenAIRE

Karpenko, Mykola; Bogdevicius, Marijonas; Prentkovskis, Olegas

2016-01-01

In the article the review of the problem of improvement of technology of high pressure hoses cutting on the hand cutting machines is analyzed. Different methods of cutting of high pressure hoses into the billets are overviewed and the quality of edge cuts of hoses is analyzed. The comparison of treatment on automatic cutting machines and on hand cutting machines is carried out. Different experimental techniques of improvement of the quality of edges cutting of high pressure hoses are prese...

On the lability and functional significance of the type 1 copper pool in ceruloplasmin.

Science.gov (United States)

Musci, G; Fraterrigo, T Z; Calabrese, L; McMillin, D R

1999-08-01

The possibility that ceruloplasmin (CP) functions as a copper transferase has fueled a continuing interest in studies of the copper release process. The principal goal of the current investigation has been to identify the most labile copper centers in sheep protein. In fact, subjecting the enzyme to a slow flux of cyanide at pH 5.2 under nitrogen in the presence of ascorbate and a phenanthroline ligand produces partially demetalated forms of the protein. By standard chromatographic techniques it is possible to isolate protein with a Cu/CP ratio of approximately 4 or approximately 5 as opposed to the native protein which has Cu/CP = 5.8. In contrast to other blue oxidases, analysis suggests that CP preferentially loses its type 1 coppers under these conditions. Thus, the spectroscopic signals from the type 1 centers exhibit a loss of intensity while the EPR signal of the type 2 copper becomes stronger. Furthermore, the Cu/CP approximately 4 and Cu/ CP approximately 5 components retain about 50% of the activity of the native protein, consistent with an intact type 2/type 3 cluster. All three type 1 copper sites appear to suffer copper loss. Reconstitution with a copper(I) reagent restores the spectroscopic properties of the native protein and 90% of the original activity. The results suggest a possible functional significance for the presence of three type 1 coppers in CP. By employing a pool of redox-active but relatively labile type 1 copper centers, the enzyme can serve as a copper donor, if necessary, without completely sacrificing its oxidase activity.

Laser cutting of various materials: Kerf width size analysis and life cycle assessment of cutting process

Science.gov (United States)

Yilbas, Bekir Sami; Shaukat, Mian Mobeen; Ashraf, Farhan

2017-08-01

Laser cutting of various materials including Ti-6Al-4V alloy, steel 304, Inconel 625, and alumina is carried out to assess the kerf width size variation along the cut section. The life cycle assessment is carried out to determine the environmental impact of the laser cutting in terms of the material waste during the cutting process. The kerf width size is formulated and predicted using the lump parameter analysis and it is measured from the experiments. The influence of laser output power and laser cutting speed on the kerf width size variation is analyzed using the analytical tools including scanning electron and optical microscopes. In the experiments, high pressure nitrogen assisting gas is used to prevent oxidation reactions in the cutting section. It is found that the kerf width size predicted from the lump parameter analysis agrees well with the experimental data. The kerf width size variation increases with increasing laser output power. However, this behavior reverses with increasing laser cutting speed. The life cycle assessment reveals that material selection for laser cutting is critical for the environmental protection point of view. Inconel 625 contributes the most to the environmental damages; however, recycling of the waste of the laser cutting reduces this contribution.

Total and labile metals in surface sediments of the tropical river-estuary system of Marabasco (Pacific coast of Mexico): Influence of an iron mine.

Science.gov (United States)

Marmolejo-Rodríguez, Ana Judith; Prego, Ricardo; Meyer-Willerer, Alejandro; Shumilin, Evgueni; Cobelo-García, Antonio

2007-01-01

Marabasco is a tropical river-estuary system comprising the Marabasco river and the Barra de Navidad Lagoon. The river is impacted by the Peña Colorada iron mine, which produces 3.5 million tons of pellets per year. Thirteen surface sediment samples were collected in May 2005 (dry season) in order to establish background levels of Al, Cd, Co, Cu, Fe, Ni, Pb, and Zn in the system and to ascertain the potential mobility of metals in the sediments. Analyses were carried out in the fraction finer than 63 microm, and labile metals extracted according the BCR procedure. Certified reference materials were used for validation of methods. Total concentrations of Cd, Co, Cu, Ni, Pb, and Zn were in the range of 0.05-0.34, 6-95, 0.7-31, 9-26, 2-18, and 53-179 mgkg(-1), respectively; Al and Fe ranges of 24-127, and 26-69 mgg(-1) correspondingly. Cadmium was found to be significantly labile in the sediments (20-100%), followed by Co (0-35%), Ni (3-16%) and Zn (0-25%), whereas the labile fraction for Cu, Fe and Pb was almost negligible (iron mine on the Marabasco system is lower than expected when compared with other similar World systems influenced by mining activities.

Suppression of inflammation in a mouse model of rheumatoid arthritis using targeted lipase-labile fumagillin prodrug nanoparticles

OpenAIRE

Zhou, Hui-fang; Yan, Huimin; Senpan, Angana; Wickline, Samuel A.; Pan, Dipanjan; Lanza, Gregory M.; Pham, Christine T.N.

2012-01-01

Nanoparticle-based therapeutics are emerging technologies that have the potential to greatly impact the treatment of many human diseases. However, drug instability and premature release from the nanoparticles during circulation currently preclude clinical translation. Herein, we use a lipase-labile (Sn 2) fumagillin prodrug platform coupled with a unique lipid surface-to-surface targeted delivery mechanism, termed contact-facilitated drug delivery, to counter the premature drug release and ov...

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Troy Reed; Ergun Kuru

2004-09-30

The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a

Practical side of cutting. Part 3. ; CO2 laser cutting. Setsudan gijutsu no jissai. 3. ; Laser setsudan

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, T.; Shinonaga, H. (Toshiba Corp., Tokyo (Japan))

1993-03-05

The nature peculiar to laser beam makes it difficult to understand the phenomena in laser cutting. Quoting an example of cutting steel materials, practical minimum basic subjects, factors governing the cutting phenomena with points to be considered, and the current state of the technology are outlined. Various kinds of expert systems and automatic programming devices have been placed on the market to make NC input easier in laser cutting. Shape accuracy, cutting quality, cutting speed, applicable plate thickness, etc. are among the subjects required for laser cutting. The factors are the method of scanning, characteristics of laser beam, work, machining conditions, etc. The factors obstructing stable processing are the change in the ambient temperature, humidity, dust, oil mist, vibration, etc. The basic factors which control the laser cutting are the power density and its distribution at the working point. Pulse cutting is employed when continuous laser heat input is not appropriate. Summarized report is made on the focal point and assist gas. 16 refs., 9 figs., 1 tab.

14C as a tracer of labile organic matter in Antarctic benthic food webs

Science.gov (United States)

Purinton, Brett L.; DeMaster, David J.; Thomas, Carrie J.; Smith, Craig R.

2008-11-01

14C measurements were made on surface plankton, particle-trap material, surface sediment, benthic invertebrate gut contents, and body tissue samples to assess the effectiveness of this radioisotope as a tracer of labile organic carbon in Antarctic benthic food webs. Samples were collected on five cruises to the West Antarctic Peninsula (WAP) shelf between November 1999 and March 2001 as part of the Food for Benthos on the ANtarctic Continental-Shelf (FOODBANCS) Project. The 14C contents of the body tissues from a variety of deposit feeders (-126±13 per mil) were substantially enriched relative to the surface sediment (-234±13 per mil) and statistically similar to the organic matter collected in plankton tows (-135±10 per mil), indicating that recently produced marine plankton are the primary source of nutrition for these deposit feeders on the West Antarctic shelf. Selective ingestion was the primary feeding strategy used by echiuran worms and certain holothurians (i.e. Peniagone vignoni) for incorporating labile organic carbon into their tissues as demonstrated by the large differences (105±13 per mil) between surface sediment and gut content 14C activities. In contrast, digestive and/or assimilatory selection was the predominant strategy used by an irregular urchin ( Amphipneustes lorioli) and several other holothurians ( Protelpidia murrayi, Bathyplotes fuscivinculum and the head-down conveyor belt feeder, Molpadia musculus), as demonstrated by large differences (42±7 per mil) between the 14C activities of their foregut or whole-gut organic contents and their body tissues. Despite large fluctuations in carbon export from the euphotic zone, benthic feeding strategies remained essentially constant over the 15-month sampling period. No seasonal variation was evident in either the 14C abundance of the deposit-feeder body tissues, or in the 14C abundance of their gut contents. The mean 14C abundance in the body tissues of the two sub-surface deposit feeders ( A

Cutting Cosmos

DEFF Research Database (Denmark)

Mikkelsen, Henrik Hvenegaard

For the first time in over 30 years, a new ethnographic study emerges on the Bugkalot tribe, more widely known as the Ilongot of the northern Philippines. Exploring the notion of masculinity among the Bugkalot, Cutting Cosmos is not only an experimental, anthropological study of the paradoxes...... around which Bugkalot society revolves, but also a reflection on anthropological theory and writing. Focusing on the transgressive acts through which masculinity is performed, this book explores the idea of the cosmic cut, the ritual act that enables the Bugkalot man to momentarily hold still the chaotic...

Latest development of laser cutting

OpenAIRE

Wetzig, Andreas; Herwig, Patrick; Hauptmann, Jan; Goppold, Cindy; Baumann, Robert; Fürst, Andreas; Rose, Michael; Pinder, Thomas; Mahrle, Achim; Beyer, Eckhard

2016-01-01

Laser cutting was one of the first applications of laser material processing. Today, laser cutting is the most widespread application among laser material processing besides laser marking. Meanwhile, nearly each material can be cut by means of a laser, in particular since ultra short pulse lasers are available in the power range of up to 100 W. The to be cut material can come with thicknesses from a few microns till tens of millimeters as flat stock or as free form shapes. The paper will conc...

CARACTERIZACION DE RIZOBACTERIAS PROMOTORAS DEL ENRAIZAMIENTO DE ESTACAS DE EUCALYPTUS GLOBULUS LABILL. : MECANISMOS DE ACCION Y FLUCTUACION POBLACIONAL

OpenAIRE

DIAZ PERALTA, KATY PAULINA; DIAZ PERALTA, KATY PAULINA

2009-01-01

Las plantaciones de Eucalyptus spp en Chile, son altamente valoradas en el mercado mundial, su producción se basa en la propagación vegetativa de plantas en viveros, a través de estacas y miniestacas; sin embargo, ex iste una variabilidad en el potencial del enraizamiento entre clones de especies e híbridos del género, lo cual no permite obtener el total de plantas en los programas de producción clonal. Diversos estudios han demostrado que bacterias rizosféricas denominadas bacterias promotor...

Plant-Soil Relationships of Bromus tectorum L.: Interactions among Labile Carbon Additions, Soil Invasion Status, and Fertilizer

International Nuclear Information System (INIS)

Blank, R.R.; Young, J.A.

2010-01-01

Invasion of western North America by the annual exotic grass Bromus tectorum L. (cheatgrass) has been an ecological disaster. High soil bioavailability of nitrogen is a contributing factor in the invasive potential of B. tectorum. Application of labile carbon sources to the soil can immobilize soil nitrogen and favor native species. We studied the interaction of labile carbon addition (sucrose), with soil invasion status and fertilizer addition on the growth of B. tectorum. Soils were non invaded (BNI) and B. tectorum invaded (BI). Treatments were control, sucrose, combined fertilizer, and sucrose + fertilizer. The greenhouse experiment continued for 3 growth-cycles. After the 1st growth-cycle, sucrose addition reduced B. tectorum aboveground mass almost 70 times for the BI soil but did not significantly reduce growth in the BNI soil. B. tectorum aboveground mass, after the 1st growth-cycle, was over 27 times greater for BI control soils than BNI control soils. Although sucrose addition reduced soil-solution NO 3 , tissue N was not significantly lowered, suggesting that reduction of soil available N may not be solely responsible for reduction in B. tectorum growth. Non invaded soil inhibits growth of B. tectorum. Understanding this mechanism may lead to viable control strategies.

Clay content drives carbon stocks in soils under a plantation of Eucalyptus saligna Labill. in southern Brazil

Directory of Open Access Journals (Sweden)

Tanise Luisa Sausen

2014-06-01

Full Text Available Soil carbon accumulation is largely dependent on net primary productivity. To our knowledge, there have been no studies investigating the dynamics of carbon accumulation in weathered subtropical soils, especially in managed eucalyptus plantations. We quantified the seasonal input of leaf litter, the leaf decomposition rate and soil carbon stocks in an commercial plantation of Eucalyptus saligna Labill. in southern Brazil. Our goal was to evaluate, through multiple linear regression, the influence that certain chemical characteristics of litter, as well as chemical and physical characteristics of soil, have on carbon accumulation in soil organic matter fractions. Variables related to the chemical composition of litter were not associated with the soil carbon stock in the particulate and mineral fractions. However, certain soil characteristics were significantly associated with the carbon stock in both fractions. The concentrations of nutrients associated with plant growth and productivity, such as phosphorus, sulfur, copper and zinc, were associated with variations in the labile carbon pool (particulate fraction. Clay content was strongly associated with the carbon stock in the mineral fraction. The carbon accumulation and stabilization in weathered subtropical Ultisol seems to be mainly associated with the intrinsic characteristics of the soil, particularly clay content, rather than with the quantity, chemical composition or decomposition rate of the litter.

CALCULATION OF LASER CUTTING COSTS

Directory of Open Access Journals (Sweden)

Bogdan Nedic

2016-09-01

Full Text Available The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, comparison' of costs made by other unconventional methods and provides documentation that consists of reports on estimated costs.

Tubing and cable cutting tool

Science.gov (United States)

Mcsmith, D. D.; Richardson, J. I. (Inventor)

1984-01-01

A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

Cutting concrete with abrasion jet

International Nuclear Information System (INIS)

Yie, G.G.

1982-01-01

Fluidyne Corporation has developed a unique process and apparatus that allow selected abrasives to be introduced into high-speed waterjet to produce abrasive-entrained waterjet that has high material-cutting capabilities, which is termed by Fluidyne as the Abrasion Jet. Such Abrasion Jet has demonstrated capability in cutting hard rock and concrete at a modest pressure of less than 1360 bars (20,000 psi) and a power input of less than 45 kW (60 horsepower). Abrasion Jet cutting of concrete is characterized by its high rate of cutting, flexible operation, good cut quality, and relatively low costs. This paper presents a general description of this technology together with discussions of recent test results and how it could be applied to nuclear decontamination and decommissioning work. 8 references

Influence of cutting parameters on the depth of subsurface deformed layer in nano-cutting process of single crystal copper.

Science.gov (United States)

Wang, Quanlong; Bai, Qingshun; Chen, Jiaxuan; Su, Hao; Wang, Zhiguo; Xie, Wenkun

2015-12-01

Large-scale molecular dynamics simulation is performed to study the nano-cutting process of single crystal copper realized by single-point diamond cutting tool in this paper. The centro-symmetry parameter is adopted to characterize the subsurface deformed layers and the distribution and evolution of the subsurface defect structures. Three-dimensional visualization and measurement technology are used to measure the depth of the subsurface deformed layers. The influence of cutting speed, cutting depth, cutting direction, and crystallographic orientation on the depth of subsurface deformed layers is systematically investigated. The results show that a lot of defect structures are formed in the subsurface of workpiece during nano-cutting process, for instance, stair-rod dislocations, stacking fault tetrahedron, atomic clusters, vacancy defects, point defects. In the process of nano-cutting, the depth of subsurface deformed layers increases with the cutting distance at the beginning, then decreases at stable cutting process, and basically remains unchanged when the cutting distance reaches up to 24 nm. The depth of subsurface deformed layers decreases with the increase in cutting speed between 50 and 300 m/s. The depth of subsurface deformed layer increases with cutting depth, proportionally, and basically remains unchanged when the cutting depth reaches over 6 nm.

Modelling stand biomass fractions in Galician Eucalyptus globulus plantations by use of different LiDAR pulse densities

Energy Technology Data Exchange (ETDEWEB)

Gonzalez-Ferreiro, E.; Miranda, D.; Barreiro-Fernandez, L.; Bujan, S.; Garcia-Gutierrez, J.; Dieguez-Aranda, U.

2013-07-01

Aims of study: To evaluate the potential use of canopy height and intensity distributions, determined by airborne LiDAR, for the estimation of crown, stem and aboveground biomass fractions. To assess the effects of a reduction in LiDAR pulse densities on model precision. Area of study: The study area is located in Galicia, NW Spain. The forests are representative of Eucalyptus globulus stands in NW Spain, characterized by low-intensity silvicultural treatments and by the presence of tall shrub. Material and methods: Linear, multiplicative power and exponential models were used to establish empirical relationships between field measurements and LiDAR metrics. A random selection of LiDAR returns and a comparison of the prediction errors by LiDAR pulse density factor were performed to study a possible loss of fit in these models. Main results: Models showed similar goodness-of-fit statistics to those reported in the international literature. R2 ranged from 0.52 to 0.75 for stand crown biomass, from 0.64 to 0.87 for stand stem biomass, and from 0.63 to 0.86 for stand aboveground biomass. The RMSE/MEAN 100 of the set of fitted models ranged from 17.4% to 28.4%. Models precision was essentially maintained when 87.5% of the original point cloud was reduced, i.e. a reduction from 4 pulses m{sup 2} to 0.5 pulses m{sup 2}. Research highlights: Considering the results of this study, the low-density LiDAR data that are released by the Spanish National Geographic Institute will be an excellent source of information for reducing the cost of forest inventories. (Author)

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

2003-09-30

The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

Using internally cooled cutting tools in the machining of difficult-to-cut materials based on Waspaloy

Directory of Open Access Journals (Sweden)

Yahya Isik

2016-05-01

Full Text Available Nickel-based superalloys such as Waspaloy are used for engine components and in the nuclear industry, where considerable strength and corrosion resistance at high operating temperatures are called for. These characteristics of such alloys cause increases in cutting temperature and resultant tool damage, even at low cutting speeds and low feed rates. Thus, they are classified as difficult-to-cut materials. This article presents a cooling method to be used in metal cutting based on a tool holder with a closed internal cooling system with cooling fluid circulating inside. Hence, a green cooling method that does not harm the environment and is efficient in removing heat from the cutting zone was developed. A series of cutting experiments were conducted to investigate the practicality and effectiveness of the internally cooled tool model. The developed system achieved up to 13% better surface quality than with dry machining, and tool life was extended by 12%. The results clearly showed that with the reduced cutting temperature of the internal cooling, it was possible to control the temperature and thus prevent reaching the critical cutting temperature during the turning process, which is vitally important in extending tool life during the processing of Waspaloy.

Laser Cutting, Development Trends

DEFF Research Database (Denmark)

Olsen, Flemming Ove

1999-01-01

In this paper a short review of the development trends in laser cutting will be given.The technology, which is the fastest expanding industrial production technology will develop in both its core market segment: Flat bed cutting of sheet metal, as it will expand in heavy industry and in cutting...... of 3-dimensional shapes.The CO2-laser will also in the near future be the dominating laser source in the market, although the new developments in ND-YAG-lasers opens for new possibilities for this laser type....

Water-Cut Sensor System

KAUST Repository

Karimi, Muhammad Akram; Shamim, Atif; Arsalan, Muhammad

2018-01-01

Provided in some embodiments is a method of manufacturing a pipe conformable water-cut sensors system. Provided in some embodiments is method for manufacturing a water-cut sensor system that includes providing a helical T-resonator, a helical ground

Effects of cutting and maturity on antioxidant activity of fresh-cut tomatoes

NARCIS (Netherlands)

Moreira Lana, M.; Tijskens, L.M.M.; Kooten, van O.

2005-01-01

To investigate the changes in total antioxidant activity of fresh-cut tomato during storage, tomato fruits harvested at three different stages of maturity were cut into 7-mm thick slices and stored at 5°C. Intact (control) fruits were stored in the same conditions. The antioxidant activity was

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2013-02-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2012-12-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

ESTIMATIVA DA BIOMASSA E DO CONTEÚDO DE NUTRIENTES DE UM POVOAMENTO DE Eucalyptus globulus (Labillardière SUB-ESPÉCIE maidenii

Directory of Open Access Journals (Sweden)

Mauro Valdir Schumacher

2000-12-01

Full Text Available O presente trabalho teve por objetivo estimar a produção de biomassa acima do solo e determinar o conteúdo de nutrientes nos diferentes componentes das árvores de um povoamento de Eucalyptus globulus subespécie maidenii. Os dados foram coletados em um talhão de 4 anos de idade, plantado em solo argiloso, no município de Butiá, Rio Grande do Sul. Para determinar a quantidade de biomassa, foi utilizada uma equação de regressão (lnY = a + b * lnX cujos coeficientes foram calculados com base em nove árvores amostradas em diferentes classes diamétricas. A biomassa total acima do solo foi de 83,2 Mg ha-1, em que 13; 10; 9 e 68 % encontravam-se distribuídos nas folhas, ramos, casca e madeira, respectivamente. Do total dos elementos na árvore, na madeira do tronco foram encontrados 29; 29; 40; 12,5 e 34% de N, P, K, Ca e Mg respectivamente. Já na copa das árvores, esses mesmos elementos representaram 64; 56; 48,5; 32 e 39%. A casca foi o componente que acumulou as maiores quantidades de cálcio, (55,3% do total.

Effect of cutting medium temperatures on rooting process and root primordium differentiation of hardwood cuttings of tetraploid robinia pseudoacacia cutting medium temperatures of tetraploid robinia pseudoacacia

International Nuclear Information System (INIS)

Ling, W.X.; Jine, Q.; Zhong, Z.

2014-01-01

In this study, to examine the effect of heat treatment on the rooting and root development of hardwood cuttings of the tetraploid Robinia pseudoacacia, cuttings of 1-year-old stems were taken from 3-year-old mother trees and treated with IBA solution (1000 mg/L) for 6 h, with water was as a control. Treated cuttings were rooted in heated or unheated nursery beds. Samples were collected on day ten after planting, and then for every five days. The bases of the cuttings were embedded in paraffin and sectioned before being examined under a microscope to determine whether there had been any morphological changes. We found no root primordia in the tissues of the hardwood cuttings of the tetraploid Robinia pseudoacacia before cutting. In the heated bed, adventitious roots originated from callus tissue and the junction between the pith rays and cortical parenchyma cells, and in the unheated bed, adventitious roots originated only from callus tissue. The rooting process involved callus formation, adventitious root formation and elongation; rooting occurred 5-7 days earlier in the heated cuttings than in the unheated ones, and rooting rates were significantly higher in the former 30 days and 50 days after cutting; the minimum effective accumulated temperatures for these three stages were 109.25 degree C, 211.68 degree C and 301.38 degree C, respectively. Our results revealed that heating the soil can promote adventitious root formation, speed up the rooting rate, and cut the propagation period of the tetraploid Robinia pseudoacacia. (author)

New Modelling Strategies For Metal Cutting

International Nuclear Information System (INIS)

Rosa, Pedro A. R.; Martins, Paulo A. F.; Atkins, Anthony G.

2007-01-01

This paper draws from the 'plasticity and friction only' view of metal cutting to the presentation of new modelling strategies based on the interaction between finite elements and modern ductile fracture mechanics. The overall presentation is supported by specially designed orthogonal metal cutting experiments that were performed on Lead test specimens under laboratory-controlled conditions. Comparisons between theoretical predictions and experimental results comprise a wide range of topics such as material flow, cutting forces and specific cutting pressure. The paper demonstrates that while material flow and chip formation can be successfully modelled by traditional 'plasticity and friction only' analyses, the contribution of the fracture work involved in the formation of new surfaces is essential for obtaining good estimates of cutting forces and of the specific cutting pressure

Cutting method and device underwater

International Nuclear Information System (INIS)

Takano, Genta; Kamei, Hiromasa; Beppu, Seiji

1998-01-01

A place of material to be cut is surrounded by an openable/closable box. The material to be cut is cut underwater, and materials generated in this case are removed from the cut portion by a pressurized water jet. The removed materials are sucked and recovered together with water in the box. Among the materials caused by the cutting underwater, solid materials not floating on water are caused to stay in the midway of a sucking and recovering channel. A large sucking force might be required for the entire region of the sucking and recovering channel when sucking and recovering large sized solid materials not floating on water, but even large sized materials can be recovered easily according to the present invention since they are recovered after being sucked and stayed in the midway of the sucking and recovering channel. (N.H.)

Cutting zone area and chip morphology in high-speed cutting of titanium alloy Ti-6Al-4V

International Nuclear Information System (INIS)

Ke, Qing Chan; Xu, Daochun; Xiong, Dan Ping

2017-01-01

The titanium alloy Ti-6Al-4V has superior properties but poor machinability, yet is widely used in aerospace and biomedical industries. Chip formation and cutting zone area are important factors that have received limited attention. Thus, we propose a high-speed orthogonal cutting model for serrated chip formation. The high speed orthogonal cutting of Ti-6Al-4V was studied with a cutting speed of 10-160 m/min and a feed of 0.07-0.11 mm/r. Using theoretical models and experimental results, parameters such as chip shape, serration level, slip angle, and shear slip distance were investigated. Cutting zone boundaries (tool-chip contact length, length of shear plane, and critical slip plane) and cutting zone area were obtained. The results showed that discontinuous, long-curling, and continuous chips were formed at low, medium, and high speeds, respectively. Serration level, shear slip distance, and slip angle rose with increasing cutting speed. The length of shear plane, tool-chip contact, and critical slip plane varied subtly with increased cutting speed, and rose noticeably with increased feed. Cutting zone area grew weakly with increased cutting speed, levelling off at high cutting speed; however, it rose noticeably with increased feed. This study furthers our understanding of the shear slip phenomenon and the mechanism of serrated chip formation

Cutting zone area and chip morphology in high-speed cutting of titanium alloy Ti-6Al-4V

Energy Technology Data Exchange (ETDEWEB)

Ke, Qing Chan; Xu, Daochun; Xiong, Dan Ping [School of Technology, Beijing Forestry University, Beijing (China)

2017-01-15

The titanium alloy Ti-6Al-4V has superior properties but poor machinability, yet is widely used in aerospace and biomedical industries. Chip formation and cutting zone area are important factors that have received limited attention. Thus, we propose a high-speed orthogonal cutting model for serrated chip formation. The high speed orthogonal cutting of Ti-6Al-4V was studied with a cutting speed of 10-160 m/min and a feed of 0.07-0.11 mm/r. Using theoretical models and experimental results, parameters such as chip shape, serration level, slip angle, and shear slip distance were investigated. Cutting zone boundaries (tool-chip contact length, length of shear plane, and critical slip plane) and cutting zone area were obtained. The results showed that discontinuous, long-curling, and continuous chips were formed at low, medium, and high speeds, respectively. Serration level, shear slip distance, and slip angle rose with increasing cutting speed. The length of shear plane, tool-chip contact, and critical slip plane varied subtly with increased cutting speed, and rose noticeably with increased feed. Cutting zone area grew weakly with increased cutting speed, levelling off at high cutting speed; however, it rose noticeably with increased feed. This study furthers our understanding of the shear slip phenomenon and the mechanism of serrated chip formation.

Effects of cutting and maturity on antioxidant activity of fresh-cut tomatoes

NARCIS (Netherlands)

Moreira Lana, M.; Tijskens, L.M.M.

2006-01-01

To investigate the changes in total antioxidant activity of fresh-cut tomato during storage, tomato fruits harvested at three different stages of maturity were cut into 7-mm thick slices and stored at 5 °C. Intact fruits were stored in the same conditions as a control. The antioxidant activity was

Respiration rate and ethylene production of fresh cut lettuce as affected by cutting grade

Directory of Open Access Journals (Sweden)

J. MARTÍNEZ

2008-12-01

Full Text Available For designing optimal polymeric films for modified atmosphere packaging of whole heads as well as for minimally fresh processed (fresh-cut Iceberg lettuce ‘Coolguard’, the effect of several cutting grades on respiration rate (RR and ethylene production at 5ºC was studied. According to common industrial practices cutting grades less than 0.5 cm, between 0.5 and 1 cm, and 2 cm length were selected. Results from four experiments were compared to those obtained for whole heads in which a homogenous range of 6 to 8 ml CO2 kg-1 h-1 in RR was found. Compared to whole heads, in fresh-cut lettuce the RR was 2-fold higher. The lowest cutting grade showed the highest respiration rate, and no significant differences in RR among lettuce pieces of intermediate and the highest grades were found. No ethylene production was detected in whole heads, while in minimally processed lettuce pieces only traces were found. For avoiding risks of anaerobic respiration and excessive CO2 levels within packages containing fresh-cut lettuce pieces lower than 0.5 cm length, films with relatively high O2 permeability like standard polypropylene or low-density polyethylene must be selected.;

Test tube systems with cutting/recombination operations

Energy Technology Data Exchange (ETDEWEB)

Freund, R. [Technische Universitaet Wien (Austria); Csuhaj-Varju, E. [Computer and Automation Institute, Budapest (Hungary); Wachtler, F. [Universitaet Wien (Austria)

1996-12-31

We introduce test tube systems based on operations that are closely related to the splicing operations, i.e. we consider the operations of cutting a string at a specific site into two pieces with marking them at the cut ends and of recombining two strings with specifically marked endings. Whereas in the splicing of two strings these strings are cut at specific sites and the cut pieces are recombined immediately in a crosswise way, in CR(cutting/recombination)-schemes cutting can happen independently from recombining the cut pieces. Test tube systems based on these operations of cutting and recombination turn out to have maximal generative power even if only very restricted types of input filters for the test tubes are used for the redistribution of the contents of the test tubes after a period of cuttings and recombinations in the test tubes. 10 refs.

Benefits of 2.94 μm infrared matrix-assisted laser desorption/ionization for analysis of labile molecules by Fourier transform mass spectrometry

DEFF Research Database (Denmark)

Budnik, Bogdan A.; Jensen, Kenneth Bendix; Jørgensen, Thomas J. D.

2000-01-01

A 2.94 microm Er:YAG laser was used together with a commercial Fourier transform mass spectrometer to study labile biomolecules. The combination has shown superior performance over conventional 337 nm ultraviolet matrix-assisted laser desorption/ionization (UV-MALDI) Fourier transform mass...

Laser cutting system

Science.gov (United States)

Dougherty, Thomas J

2015-03-03

A workpiece cutting apparatus includes a laser source, a first suction system, and a first finger configured to guide a workpiece as it moves past the laser source. The first finger includes a first end provided adjacent a point where a laser from the laser source cuts the workpiece, and the first end of the first finger includes an aperture in fluid communication with the first suction system.

Trim cut machining and surface integrity analysis of Nimonic 80A alloy using wire cut EDM

Directory of Open Access Journals (Sweden)

Amitesh Goswami

2017-02-01

Full Text Available This present work deals with the features of trim cut wire EDM machining of Nimonic 80A in terms of machining parameters, to predict material removal rate (MRR, surface roughness (Ra, wire wear ratio (WWR and microstructure analysis. Trim cut is performed after rough cut to remove the rough layer deposited after machining due to melting and re-solidification of the eroded metal from workpiece as well as from wire electrode. Taguchi’s design of experiments methodology has been used for planning and designing the experiments. The relative significance of various factors has also been evaluated and analyzed using ANOVA. The results clearly indicate trim cut potential for high surface finish compared to rough cut machining.

Laser Cutting of Carbon Fiber Fabrics

Science.gov (United States)

Fuchs, A. N.; Schoeberl, M.; Tremmer, J.; Zaeh, M. F.

Due to their high weight-specific mechanical stiffness and strength, parts made from carbon fiber reinforced polymers (CFRP) are increasingly used as structural components in the aircraft and automotive industry. However, the cutting of preforms, as with most automated manufacturing processes for CFRP components, has not yet been fully optimized. This paper discusses laser cutting, an alternative method to the mechanical cutting of preforms. Experiments with remote laser cutting and gas assisted laser cutting were carried out in order to identify achievable machining speeds. The advantages of the two different processes as well as their fitness for use in mass production are discussed.

Automated Laser Cutting In Three Dimensions

Science.gov (United States)

Bird, Lisa T.; Yvanovich, Mark A.; Angell, Terry R.; Bishop, Patricia J.; Dai, Weimin; Dobbs, Robert D.; He, Mingli; Minardi, Antonio; Shelton, Bret A.

1995-01-01

Computer-controlled machine-tool system uses laser beam assisted by directed flow of air to cut refractory materials into complex three-dimensional shapes. Velocity, position, and angle of cut varied. In original application, materials in question were thermally insulating thick blankets and tiles used on space shuttle. System shapes tile to concave or convex contours and cuts beveled edges on blanket, without cutting through outer layer of quartz fabric part of blanket. For safety, system entirely enclosed to prevent escape of laser energy. No dust generated during cutting operation - all material vaporized; larger solid chips dislodged from workpiece easily removed later.

Identification and characterization of a novel Cut family cDNA that encodes human copper transporter protein CutC

International Nuclear Information System (INIS)

Li Jixi; Ji Chaoneng; Chen Jinzhong; Yang Zhenxing; Wang Yijing; Fei, Xiangwei; Zheng Mei; Gu Xing; Wen Ge; Xie Yi; Mao Yumin

2005-01-01

Copper is an essential heavy metal trace element that plays important roles in cell physiology. The Cut family was associated with the copper homeostasis and involved in several important metabolisms, such as uptake, storage, delivery, and efflux of copper. In this study, a novel Cut family cDNA was isolated from the human fetal brain library, which encodes a 273 amino acid protein with a molecular mass of about 29.3 kDa and a calculated pI of 8.17. It was named hCutC (human copper transporter protein CutC). The ORF of hCutC gene was cloned into pQE30 vector and expressed in Escherichia coli M15. The secreted hCutC protein was purified to a homogenicity of 95% by using the Ni-NTA affinity chromatography. RT-PCR analysis showed that the hCutC gene expressed extensively in human tissues. Subcellular location analysis of hCutC-EGFP fusion protein revealed that hCutC was distributed to cytoplasm of COS-7 cells, and both cytoplasm and nucleus of AD293 cells. The results suggest that hCutC may be one shuttle protein and play important roles in intracellular copper trafficking

Changes in lead and zinc lability during weathering-induced acidification of desert mine tailings: Coupling chemical and micro-scale analyses

International Nuclear Information System (INIS)

Hayes, Sarah M.; White, Scott A.; Thompson, Thomas L.; Maier, Raina M.; Chorover, Jon

2009-01-01

Desert mine tailings may accumulate toxic metals in the near surface centimeters because of low water through-flux rates. Along with other constraints, metal toxicity precludes natural plant colonization even over decadal time scales. Since unconsolidated particles can be subjected to transport by wind and water erosion, potentially resulting in direct human and ecosystem exposure, there is a need to know how the lability and form of metals change in the tailings weathering environment. A combination of chemical extractions, X-ray diffraction, micro-X-ray fluorescence spectroscopy, and micro-Raman spectroscopy were employed to study Pb and Zn contamination in surficial arid mine tailings from the Arizona Klondyke State Superfund Site. Initial site characterization indicated a wide range in pH (2.5-8.0) in the surficial tailings pile. Ligand-promoted (DTPA) extractions, used to assess plant-available metal pools, showed decreasing available Zn and Mn with progressive tailings acidification. Aluminum shows the inverse trend, and Pb and Fe show more complex pH dependence. Since the tailings derive from a common source and parent mineralogy, it is presumed that variations in pH and 'bio-available' metal concentrations result from associated variation in particle-scale geochemistry. Four sub-samples, ranging in pH from 2.6 to 5.4, were subjected to further characterization to elucidate micro-scale controls on metal mobility. With acidification, total Pb (ranging from 5 to 13 g kg -1 ) was increasingly associated with Fe and S in plumbojarosite aggregates. For Zn, both total (0.4-6 g kg -1 ) and labile fractions decreased with decreasing pH. Zinc was found to be primarily associated with the secondary Mn phases manjiroite and chalcophanite. The results suggest that progressive tailings acidification diminishes the overall lability of the total Pb and Zn pools.

Complexation efficiency of differently fixed 8-hydroxyquinoline and salicylic acid ligand groups for labile aluminium species determination in soils-comparison of two methods

International Nuclear Information System (INIS)

Matus, Peter; Kubova, Jana

2006-01-01

Two methods utilizing the complexation of labile Al species by 8-hydroxyquinoline (HQN) and salicylic acid (SA) ligand groups were developed for aluminium operationally defined fractionation in acid soils. First, the solid phase extraction (SPE) procedure by a short-term ion-exchange batch reaction with chelating resins Iontosorb Oxin and Iontosorb Salicyl containing both ligand groups was used previously. Second, the 8-hydroxyquinoline, salicylic acid and ammonium salicylate agents with different concentrations by a single extraction protocol were applied in this paper. The flame atomic absorption spectrometry (FAAS) and optical emission spectrometry with inductively coupled plasma were used for aluminium quantification. The comparison of results from both methods show the possibility to supersede the first laborious method for the second simpler one in Al environmental risk assessment. The use of 1% 8-hydroxyquinoline in 2% acetic acid and 0.2% salicylic acid by a single extraction protocol without a need of sample filtration can supersede the SPE procedure in the Al pollution soil monitoring. Finally, the new scheme usable in a laboratory and moreover, directly in a field was proposed for Al fractionation in solid and liquid environmental samples. The labile Al species in soils and sediments are separated after their single leaching by 8-hydroxyquinoline or salicylic acid without a need of sample filtration. The labile Al species in soil solutions and natural waters are separated after their ultrafiltration followed by the SPE procedure with Iontosorb Oxin or Iontosorb Salicyl

Marked lability in urinary cortisol levels in subgroups of combat veterans with posttraumatic stress disorder during an intensive exposure treatment program.

Science.gov (United States)

Mason, John W; Wang, Sheila; Yehuda, Rachel; Lubin, Hadar; Johnson, David; Bremner, J Douglas; Charney, Dennis; Southwick, Steven

2002-01-01

The objective of this study was to obtain longitudinal data on lability of cortisol levels in posttraumatic stress disorder (PTSD) because previous studies have largely been based on sampling at a single time point and have yielded varying results. This study measured urinary cortisol levels at admission, midcourse, and discharge during a 90-day hospitalization period in male Vietnam combat veterans with PTSD (N = 51). Although there were no significant differences in the mean +/- SEM urinary cortisol levels between the admission (59.4 +/- 3.0 microg/d), midcourse (55.6 +/- 3.9 microg/d), and discharge (53.4 +/- 3.4 microg/d) values, marked lability of cortisol levels in individual patients was observed over time, with changes ranging from +93 to -58 microg/d from admission to midcourse. In addition, this hormonal lability defined discrete subgroups of patients on the basis of the longitudinal pattern of cortisol change during exposure treatment, and there were significant psychometric differences in the level of social functioning between these subgroups. The findings do not support the concept of either a static "hypocortisolism" or "hypercortisolism" in PTSD, but rather suggest a psychogenic basis for cortisol alterations in PTSD in relation to psychosocial stress and indicate a central regulatory dysfunction of the hypothalamic-pituitary-adrenal axis characterized by a dynamic tendency to overreact in both upward and downward directions. The longitudinal findings fit with recent observations that cortisol elevations occur when acutely superimposed stressful conditions emotionally engage patients and overwhelm the usually dominating disengaging coping mechanisms associated with suppression of cortisol levels in PTSD. The findings emphasize the importance of longitudinal data in studies of the hypothalamic-pituitary-adrenal axis in PTSD.

The preliminary attempts of in in vitro regeneration from petioles of recalcitrant species of Cephalotus follicularis Labill.

OpenAIRE

Tuleja M.; Chmielowska A.; Płachno B.

2014-01-01

Cephalotus follicularis Labill. is representative of the extraordinary carnivorous group of plants. Carnivorous plants with pitcher traps grow in nutrient poor, sunny and wet habitats, they have adapted themselves to growth in bogs, sandy soils and obtain some nutrients (e.g. nitrogen and phosphate) from insects and other arthropods or protozoa, even from small mammals occasionally (Król et al. 2012). C. follicularis belongs to the monotypic family Cephalotaceae, and it is the endemic plant o...

Laser Cutting of Different Materials

Directory of Open Access Journals (Sweden)

Kadir ÇAVDAR

2013-08-01

Full Text Available In this paper; in general potential developments and trends of a particular machining field by extensively evaluating present studies of laser beam machining have been discussed. As it is indicated below, technical literatures have been subsumed under five major headlines: Experimental studies, reviews, optimization researches of the cutting parameters, theoretical modelling studies of laser beam cutting and academic studies relating to laser cutting

Comparative study of 0° X-cut and Y + 36°-cut lithium niobate high-voltage sensing

Science.gov (United States)

Patel, N.; Branch, D. W.; Schamiloglu, E.; Cular, S.

2015-08-01

A comparison study between Y + 36° and 0° X-cut lithium niobate (LiNbO3) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y + 36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5 μs voltage pulses to both crystals, the voltage-induced shift scaled linearly with voltage. For the Y + 36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz-100 kHz. Using the same conditions as the Y + 36° cut, the 0° X-cut crystal sensed a shift of 10-273 ps for DC voltages and 189-813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250-2 ns and the Y + 36°-cut crystal sensed a time shift of 0.115-1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. When the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment.

A Biorefinery Cascade Conversion of Hemicellulose-Free Eucalyptus Globulus Wood: Production of Concentrated Levulinic Acid Solutions for γ-Valerolactone Sustainable Preparation

Directory of Open Access Journals (Sweden)

Sandra Rivas

2018-04-01

Full Text Available Eucalyptus globulus wood samples were subjected to preliminary aqueous processing to remove water-soluble extractives and hemicelluloses, and the resulting solid (mainly made up of cellulose and lignin was employed as a substrate for converting the cellulosic fraction into mixtures of levulinic and formic acid through a sulfuric acid-catalyzed reaction. These runs were carried out in a microwave-heated reactor at different temperatures and reaction times, operating in single-batch or cross-flow modes, in order to identify the most favorable operational conditions. Selected liquid phases deriving from these experiments, which resulted in concentrated levulinic acid up to 408 mmol/L, were then employed for γ-valerolactone production by levulinc acid hydrogenation in the presence of the commercial 5% Ru/C catalyst. In order to assess the effects of the main reaction parameters, hydrogenation experiments were performed at different temperatures, reaction times, amounts of ruthenium catalyst and hydrogen pressure. Yields of γ-valerolactone in the range of 85–90 mol % were obtained from the hydrogenation of the wood-derived solutions containing levulinic acid, obtained by single-batch operation or by the cross-flow process. The negative effect of co-produced formic acid present in crude levulinic acid solutions was evidenced and counteracted efficiently by allowing the preliminary thermal decomposition of formic acid itself.

Optical Cutting Interruption Sensor for Fiber Lasers

Directory of Open Access Journals (Sweden)

Benedikt Adelmann

2015-09-01

Full Text Available We report on an optical sensor system attached to a 4 kW fiber laser cutting machine to detect cutting interruptions. The sensor records the thermal radiation from the process zone with a modified ring mirror and optical filter arrangement, which is placed between the cutting head and the collimator. The process radiation is sensed by a Si and InGaAs diode combination with the detected signals being digitalized with 20 kHz. To demonstrate the function of the sensor, signals arising during fusion cutting of 1 mm stainless steel and mild steel with and without cutting interruptions are evaluated and typical signatures derived. In the recorded signals the piercing process, the laser switch on and switch off point and waiting period are clearly resolved. To identify the cutting interruption, the signals of both Si and InGaAs diodes are high pass filtered and the signal fluctuation ranges being subsequently calculated. Introducing a correction factor, we identify that only in case of a cutting interruption the fluctuation range of the Si diode exceeds the InGaAs diode. This characteristic signature was successfully used to detect 80 cutting interruptions of 83 incomplete cuts (alpha error 3.6% and system recorded no cutting interruption from 110 faultless cuts (beta error of 0. This particularly high detection rate in combination with the easy integration of the sensor, highlight its potential for cutting interruption detection in industrial applications.

The DIRT on Q10: In situ depletion of labile-inputs does not increase temperature sensitivity in a laboratory incubation (Invited)

Science.gov (United States)

Reynolds, L. L.; Lajtha, K.; Bowden, R.; Johnson, B. R.; Bridgham, S. D.

2013-12-01

The decomposition of soil organic matter is expected to increase with global warming and has been commonly described by kinetic models with at least two pools with differing turnover times. Pools characterized by rapid turnover are thought to consist of labile substrates. Meanwhile, slower turnover is attributed, in part, to greater chemical complexity and a necessarily higher activation energy which should in turn lead to a higher sensitivity (Q10) to temperature and a proportionally larger response to warming. Experimental tests of the relative Q10 of these pools have been inconclusive and contradictory in part due the fact that all pools are decomposing simultaneously and soils kept under differing conditions over long periods of time diverge in more than the Q10 response making them less comparable over time. We present here a test of the temperature response on soils from a 20 yr litter manipulation experiment incubated under an experimental regime that minimizes divergence among the soils. We hypothesize that 1) if exclusion of inputs has depleted labile substrates and 2) the remaining carbon is more chemically complex, then the input exclusion treatments should show a higher Q10 compared to the ambient or increased input treatments. The soils are taken from the Detritus Input and Removal Treatment (DIRT) plots in the Bousson Forest, Pennsylvania, US. The DIRT treatments consist of litter and root exclusion (no inputs = NI), no roots (NR), no litter (NL), double litter (DL), and ambient conditions (C). Soils were incubated at 25oC for 525 days. Periodically, replicate sets were rotated into 15oC, 35oC or remained at 25oC for 24 hr. The headspace CO2 concentration was measured before and after the 24 hr temperature treatments, and then all replicate sets were returned to 25oC. Twenty years of input exclusion decreased respiration rate, with NI DIRT treatments, despite the clear differences in their carbon pools. Similar studies have examined the temperature

Structural lability of Barley stripe mosaic virus virions.

Directory of Open Access Journals (Sweden)

Valentin V Makarov

Full Text Available Virions of Barley stripe mosaic virus (BSMV were neglected for more than thirty years after their basic properties were determined. In this paper, the physicochemical characteristics of BSMV virions and virion-derived viral capsid protein (CP were analyzed, namely, the absorption and intrinsic fluorescence spectra, circular dichroism spectra, differential scanning calorimetry curves, and size distributions by dynamic laser light scattering. The structural properties of BSMV virions proved to be intermediate between those of Tobacco mosaic virus (TMV, a well-characterized virus with rigid rod-shaped virions, and flexuous filamentous plant viruses. The BSMV virions were found to be considerably more labile than expected from their rod-like morphology and a distant sequence relation of the BSMV and TMV CPs. The circular dichroism spectra of BSMV CP subunits incorporated into the virions, but not subunits of free CP, demonstrated a significant proportion of beta-structure elements, which were proposed to be localized mostly in the protein regions exposed on the virion outer surface. These beta-structure elements likely formed during virion assembly can comprise the N- and C-terminal protein regions unstructured in the non-virion CP and can mediate inter-subunit interactions. Based on computer-assisted structure modeling, a model for BSMV CP subunit structural fold compliant with the available experimental data was proposed.

Radioactive wear measurements of cutting tools made of metal in cutting aluminium alloys

International Nuclear Information System (INIS)

Frevert, E.

1977-01-01

The possibility of making quick checkings of the inhomogeneities of turning materials with radioactive wear measurements has been tested. After activation analysis of the long-lived radioisotopes of cutting tools made of hard metal a method for loss-free collection of the turnings has been developed. The detection limit of the abrasion is about 10 -8 g, the measuring times are 5-10 minutes. Special radiation protection measures are not necessary. An analysis of the abrasion showed that at the beginning of cutting the amount of cobalt is 6 times higher than in the normal composition of the used cutting tools. (author)

Economic technology of laser cutting

Science.gov (United States)

Fedin, Alexander V.; Shilov, Igor V.; Vassiliev, Vladimir V.; Malov, Dmitri V.; Peskov, Vladimir N.

2000-02-01

The laser cutting of color metals and alloys by a thickness more than 2 mm has significant difficulties due to high reflective ability and large thermal conduction. We made it possible to raise energy efficiency and quality of laser cutting by using a laser processing system (LPS) consisting both of the YAG:Nd laser with passive Q-switching on base of LiF:F2- crystals and the CO2 laser. A distinctive feature of the LPS is that the radiation of different lasers incorporated in a coaxial beam has simultaneously high level of peak power (more than 400 kW in a TEM00 mode) and significant level of average power (up to 800 W in a TEM01 mode of the CO2 laser). The application of combined radiation for cutting of an aluminum alloy of D16 type made it possible to decrease the cutting energy threshold in 1.7 times, to increase depth of treatment from 2 up to 4 mm, and velocity from 0.015 up to 0.7 m/min, and also to eliminate application of absorptive coatings. At cutting of steels the velocity of treatment was doubled, and also an oxygen flow was eliminated from the technological process and replaced by the air. The obtained raise of energy efficiency and quality of cutting is explained by an essential size reducing of a formed penetration channel and by the shifting of a thermal cutting mode from melting to evaporation. The evaluation of interaction efficiency of a combined radiation was produced on the basis of non-stationary thermal-hydrodynamic model of a heating source moving as in the cutting direction, and also into the depth of material.

Development of cutting device for irradiated fuel rod

International Nuclear Information System (INIS)

Lee, E. P.; Jun, Y. B.; Hong, K. P.; Min, D. K.; Lee, H. K.; Su, H. S.; Kim, K. S.; Kwon, H. M.; Joo, Y. S.; Yoo, K. S.; Joo, J. S.; Kim, E. K.

2004-01-01

Post Irradiation Examination(PIE) on irradiated fuel rods is essential for the evaluation of integrity and irradiation performance of fuel rods of commercial reactor fuel. For PIE, fuel rods should be cut very precisely. The cutting positions selected from NDT data are very important for further destructive examination and analysis. A fuel rod cutting device was developed witch can cut fuel rods longitudinal very precisely and can also cut the fuels into the same length rod cuts repeatedly. It is also easy to remove the fuel cutting powder after cutting works and it can extend the life time of cutting device and lower the contamination level of hot cell

Decomposição de agulhas de Pinus pinaster e de folhas de Eucalyptus globulus em regiões do interior e do litoral de Portugal Decomposition of needle litter of Pinus pinaster and leaf litter of Eucalyptus globulus in the littoral and inland areas of Portugal

Directory of Open Access Journals (Sweden)

C. Ribeiro

2007-07-01

Full Text Available Estudou-se, pela metodologia dos litter-bags, a decomposição de agulhas de Pinus pinaster (PP e de folhas de Eucalyptus globulus (EG, considerando a taxa de decomposição e a dinâmica de libertação dos nutrientes mais relevantes para a sustentabilidade dos sistemas florestais. Os estudos decorreram no litoral da Região Centro (Furadouro, Óbidos, quer com folhas de EG quer com agulhas de PP, no interior da Região Norte (Vila Pouca de Aguiar, com agulhas de PP, e numa situação intermédia com folhas de EG (Pegões e Rio Maior. Para igual período, a taxa de decomposição das agulhas de PP, estimada pelo modelo exponencial simples, foi inferior à determinada para as folhas de EG, sendo a diferença mais acentuada na fase inicial da decomposição (6 meses, em que a perda de peso das agulhas de PP foi cerca de metade da observada para as folhas de EG. Durante a fase inicial decomposição, tanto das folhas de EG como das agulhas de PP, ocorreu uma assinalável libertação de P, K e de Mg. A libertação do N dependeu da taxa de decomposição, observando- -se imobilização para as agulhas de PP com mais baixa taxa de decomposição, e libertação rápida para as folhas de EG com mais elevada taxa de decomposição. No caso do Ca o factor diferenciador foi a espécie, sendo a respectiva libertação baixa para as agulhas de PP, mas acentuada para as folhas de EG. As folhas verdes de resíduos de abate de EG decompuseram-se e libertaram os nutrientes mais rapidamente do que as folhas senescentes da mesma espécie.Decomposition of needle litter of Pinus pinaster (PP and leaf litter of Eucalyptus globulus (EG was assessed using the litterbag methodology. Decomposition rate of these residues and release dynamics of nutrients with more relevance to the sustainability of forest systems were measured. The study was carried out in the litoral of Central Portugal (Furadouro,Óbidos, using both PP and EG, in inland of North Portugal (Vila Pouca

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Lei Zhou

2000-01-30

This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members. The tasks Completed During This Quarter are Task 7 and Task 8.

The acid-labile subunit of the ternary insulin-like growth factor complex in cirrhosis: relation to liver dysfunction

DEFF Research Database (Denmark)

Møller, S; Juul, A; Becker, U

2000-01-01

BACKGROUND/AIMS: In the circulation, insulin-like growth factor-I (IGF-I) is bound in a trimeric complex of 150 kDa with IGF binding protein-3 (IGFBP-3) and the acid-labile subunit (ALS). Whereas circulating IGF-I and IGFBP-3 are reported to be low in patients with chronic liver failure, the leve...... with significant relations to liver dysfunction and other components of the IGF complex. A small hepatic extraction was found in controls, which suggests extrahepatic production of ALS. Future studies should focus on organ-specific removal of ALS.......BACKGROUND/AIMS: In the circulation, insulin-like growth factor-I (IGF-I) is bound in a trimeric complex of 150 kDa with IGF binding protein-3 (IGFBP-3) and the acid-labile subunit (ALS). Whereas circulating IGF-I and IGFBP-3 are reported to be low in patients with chronic liver failure, the level...... of ALS has not been described in relation to hepatic dysfunction. The aim of the present study was therefore to measure circulating and hepatic venous concentrations of ALS in relation to hepatic function and the IGF axis. METHODS: Twenty-five patients with cirrhosis (Child class A/B/C:5/10/10) and 30...

Herbal distillates: A new era of grape marc distillates with enriched antioxidant profile.

Science.gov (United States)

Andreou, Vasiliki; Strati, Irini F; Fotakis, Charalambos; Liouni, Maria; Zoumpoulakis, Panagiotis; Sinanoglou, Vassilia J

2018-07-01

Grape marc distillates are traditional alcoholic beverages, produced mostly in the Mediterranean countries. The present study proposes the enrichment of a Greek traditional grape marc distillate (tsikoudia) with selected herbs to enhance its natural antioxidants and functional properties. Total phenolic content, the antiradical and antioxidant activities, as well as the phenolic and sugar profiles using NMR and FT-IR spectroscopy were evaluated. The enrichment of distillates with Syzygium aromaticum L., Jasminum officinale L. and Eucalyptus globulus Labill. exhibited the highest total phenolic content as well as the highest antioxidant and antiradical activities, whereas the lowest values were observed with Hippophae rhamnoides L. and Lycium Barbarum Mill. The implementation of NMR and FT-IR spectroscopies attested to the presence of phenolic compounds and of specific carbohydrates in herbal distillates, postulating their migration from selected herbal species to tsikoudia and probably contributing to their organoleptic characteristics. The target of this approach leads to new added-value distillates with enhanced characteristics. Copyright © 2018 Elsevier Ltd. All rights reserved.

Submerged cutting characteristics of abrasive suspension jet

International Nuclear Information System (INIS)

Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroyuki

2015-01-01

An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth under submerged condition divided by the cutting depth in air at the same standoff distance. The relative cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM.

Science.gov (United States)

Shen, Qi; Liu, Zhanqiang; Hua, Yang; Zhao, Jinfu; Lv, Woyun; Mohsan, Aziz Ul Hassan

2018-06-14

Service performance of components such as fatigue life are dramatically influenced by the machined surface and subsurface residual stresses. This paper aims at achieving a better understanding of the influence of cutting edge microgeometry on machined surface residual stresses during orthogonal dry cutting of Inconel 718. Numerical and experimental investigations have been conducted in this research. The cutting edge microgeometry factors of average cutting edge radius S¯, form-factor K , and chamfer were investigated. An increasing trend for the magnitudes of both tensile and compressive residual stresses was observed by using larger S¯ or introducing a chamfer on the cutting edges. The ploughing depth has been predicted based on the stagnation zone. The increase of ploughing depth means that more material was ironed on the workpiece subsurface, which resulted in an increase in the compressive residual stress. The thermal loads were leading factors that affected the surface tensile residual stress. For the unsymmetrical honed cutting edge with K = 2, the friction between tool and workpiece and tensile residual stress tended to be high, while for the unsymmetrical honed cutting edge with K = 0.5, the high ploughing depth led to a higher compressive residual stress. This paper provides guidance for regulating machine-induced residual stress by edge preparation.

Quantum Max-flow/Min-cut

Science.gov (United States)

Cui, Shawn X.; Freedman, Michael H.; Sattath, Or; Stong, Richard; Minton, Greg

2016-06-01

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

Quantum Max-flow/Min-cut

Energy Technology Data Exchange (ETDEWEB)

Cui, Shawn X., E-mail: xingshan@math.ucsb.edu [Department of Mathematics, University of California, Santa Barbara, California 93106 (United States); Quantum Architectures and Computation Group, Microsoft Research, Redmond, Washington 98052 (United States); Freedman, Michael H., E-mail: michaelf@microsoft.com [Department of Mathematics, University of California, Santa Barbara, California 93106 (United States); Microsoft Research, Station Q, University of California, Santa Barbara, California 93106 (United States); Sattath, Or, E-mail: sattath@gmail.com [Computer Science Division, University of California, Berkeley, California 94720 (United States); Stong, Richard, E-mail: stong@ccrwest.org; Minton, Greg, E-mail: gtminto@ccrwest.org [Center for Communications Research, La Jolla, California 92121 (United States)

2016-06-15

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

Cutting Class Harms Grades

Science.gov (United States)

Taylor, Lewis A., III

2012-01-01

An accessible business school population of undergraduate students was investigated in three independent, but related studies to determine effects on grades due to cutting class and failing to take advantage of optional reviews and study quizzes. It was hypothesized that cutting classes harms exam scores, attending preexam reviews helps exam…

BIOMASS IN Eucalyptus viminalis Labill. PLANTATIONS IN BUENOS AIRES PROVINCE, ARGENTINA

Directory of Open Access Journals (Sweden)

Paula Ferrere

2009-10-01

Full Text Available The present work was developed in the West of Buenos Aires Province (Argentina with the objective of adjusting functions of biomass of individual trees, in their different compartments and in the understorey. Stands of Eucalyptus viminalis Labill. were identified, with ages between 4 and 14 years-old. Twenty-one individuals were felled with diameters ranging from 9,2 to 32,5 cm. Simple and multiple regression models were developed and volume, branch leaf and stem biomass were estimated. The best volume equations were based on lineal models and the most adequate behavior was obtained with d2. To estimate leaf, branch and stem, ln-ln models have been suggested, with diameter and h or only diameter. The leaf biomass presented the weakest adjustment. The distribution of trees biomass agrees with the bibliography. The proportion of crown biomass decreases with age; on the other hand, the proportion of stem biomass increases with age.

Sodium-cutting: a new top-down approach to cut open nanostructures on nonplanar surfaces on a large scale.

Science.gov (United States)

Chen, Wei; Deng, Da

2014-11-11

We report a new, low-cost and simple top-down approach, "sodium-cutting", to cut and open nanostructures deposited on a nonplanar surface on a large scale. The feasibility of sodium-cutting was demonstrated with the successfully cutting open of ∼100% carbon nanospheres into nanobowls on a large scale from Sn@C nanospheres for the first time.

Multi-Criteria Analysis of Laser Cut Surface Characteristics in CO2 Laser Cutting of Stainless Steel

Directory of Open Access Journals (Sweden)

M. Radovanović

2015-06-01

Full Text Available In this paper an approach for multi-criteria analysis of laser cut surface characteristics using multi-criteria decision making (MCDM approach was presented. Laser cutting experiment was conducted based on Taguchi’s L27 experimental design by varying laser power, cutting speed, assist gas pressure and focus position at three levels. Multi-criteria analysis was performed by using the weighted aggregated sum product assessment (WASPAS method while considering burr height, drag line separation, depth of separation line, surface roughness and perpendicularity of the cut as assessment criteria. Based on conducted experimental investigation the MCDM model with 27 alternatives (laser cuts and five criteria was developed. The relative importance of criteria was determined by using pair-wise comparison matrix and geometric mean method of the analytic hierarchy process (AHP method.

Material testing of copper by extrusion-cutting

DEFF Research Database (Denmark)

Segalina, F.; De Chiffre, Leonardo

2017-01-01

was developed and implemented on a CNC lathe. An investigation was carried out extrusion-cutting copper discs using high-speed-steel cutting tools at 100 m/min cutting speed. Flow stress values for copper under machining-relevant conditions were obtained from measurement of the extrusion-cutting force...

Baikov-Lee representations of cut Feynman integrals

International Nuclear Information System (INIS)

Harley, Mark; Moriello, Francesco; Schabinger, Robert M.

2017-01-01

We develop a general framework for the evaluation of d-dimensional cut Feynman integrals based on the Baikov-Lee representation of purely-virtual Feynman integrals. We implement the generalized Cutkosky cutting rule using Cauchy’s residue theorem and identify a set of constraints which determine the integration domain. The method applies equally well to Feynman integrals with a unitarity cut in a single kinematic channel and to maximally-cut Feynman integrals. Our cut Baikov-Lee representation reproduces the expected relation between cuts and discontinuities in a given kinematic channel and furthermore makes the dependence on the kinematic variables manifest from the beginning. By combining the Baikov-Lee representation of maximally-cut Feynman integrals and the properties of periods of algebraic curves, we are able to obtain complete solution sets for the homogeneous differential equations satisfied by Feynman integrals which go beyond multiple polylogarithms. We apply our formalism to the direct evaluation of a number of interesting cut Feynman integrals.

Comparison of cutting efficiency with different diamond burs and water flow rates in cutting lithium disilicate glass ceramic.

Science.gov (United States)

Siegel, Sharon C; Patel, Tejas

2016-10-01

This study compared different diamond burs and different water flow rates on the cutting efficiency of sectioning through lithium disilicate glass ceramic. The authors used a standardized cutting regimen with 4 brands of diamond burs to section through lithium disilicate glass ceramic blocks. Twelve diamonds of each brand cut through the blocks in randomized order. In the first part of the study, the authors recorded sectioning rates in millimeters per minute for each diamond bur as a measure of cutting efficiency. In the second part of the study, the authors compared sectioning rates using only 1 brand of diamond bur, with 3 different water flow rates. The authors averaged and compared cutting rates of each brand of diamond bur and the cutting rates for each flow rate using an analysis of variance and determined the differences with a Tukey honest significant difference test. One diamond bur cut significantly slower than the other 3, and one diamond bur cut significantly faster than 2 of the others. The diamond bur cutting efficiency through lithium disilicate glass ceramic with a 20 mL/min water flow rate was significantly higher than 15 mL/min. There are differences in cutting efficiency between diamond burs when sectioning lithium disilicate glass ceramic. Use a minimum of 20 mL/min of water coolant flow when sectioning lithium disilicate glass ceramic with dental diamond burs to maximize cutting efficiency. Recommendations for specific diamond burs with a coarse grit and water flow rate of 20 mL/min can be made when removing or adjusting restorations made from lithium disilicate glass ceramic. Copyright © 2016 American Dental Association. Published by Elsevier Inc. All rights reserved.

Comparative study of 0° X-cut and Y + 36°-cut lithium niobate high-voltage sensing

International Nuclear Information System (INIS)

Patel, N.; Branch, D. W.; Cular, S.; Schamiloglu, E.

2015-01-01

A comparison study between Y + 36° and 0° X-cut lithium niobate (LiNbO 3 ) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y + 36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5 μs voltage pulses to both crystals, the voltage-induced shift scaled linearly with voltage. For the Y + 36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz–100 kHz. Using the same conditions as the Y + 36° cut, the 0° X-cut crystal sensed a shift of 10–273 ps for DC voltages and 189–813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250–2 ns and the Y + 36°-cut crystal sensed a time shift of 0.115–1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. When the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment

Underwater laser cutting of metallic structures

International Nuclear Information System (INIS)

Alfille, J.P.; Schildknecht, J.; Ramaswami, V.S.

1993-01-01

In the frame of an european contract, the feasibility of the underwater cutting with a CO 2 laser power is studied. The aim of this work is the dismantling metallic structures of reactors pools. The paper analyzes the general concept of the experimental device, the underwater cutting head, the experimenting vessel, examples of cuttings in dismantling situation with a 500 W CO 2 laser, and examples of cuttings with a 5 kW CO 2 laser. (author). 2 refs., 9 figs., 2 tabs

Theoretical aspects of fibre laser cutting

Energy Technology Data Exchange (ETDEWEB)

Mahrle, A; Beyer, E, E-mail: achim.mahrle@iws.fraunhofer.d [University of Technology Dresden, Institute for Surface and Manufacturing Technology, PO Box, 01062 Dresden (Germany)

2009-09-07

Fibre lasers offer distinct advantages over established laser systems with respect to power efficiency, beam guidance and beam quality. Consequently, the potential of these new laser beam sources will be increasingly exploited for laser cutting applications that are conventionally carried out with CO{sub 2} lasers. However, theoretical estimates of the effective absorptivity at the cut front suggest that the shorter wavelength of the fibre laser in combination with its high focusability seems to be primarily advantageous for thin sheet metal cutting whereas the CO{sub 2} laser is probably still capable of cutting thicker materials more efficiently. This surprising result is a consequence of the absorptivity behaviour of metals that shows essential quantitative differences for the corresponding wavelengths of both laser sources as a function of the angle of incidence between the laser beam and the material to be cut. In evaluation of the revealed dependences, solution strategies for an improvement of the efficiency of fibre laser cutting of thicker metal sheets are suggested.

A universal fluorogenic switch for Fe(ii) ion based on N-oxide chemistry permits the visualization of intracellular redox equilibrium shift towards labile iron in hypoxic tumor cells.

Science.gov (United States)

Hirayama, Tasuku; Tsuboi, Hitomi; Niwa, Masato; Miki, Ayaji; Kadota, Satoki; Ikeshita, Yukie; Okuda, Kensuke; Nagasawa, Hideko

2017-07-01

Iron (Fe) species play a number of biologically and pathologically important roles. In particular, iron is a key element in oxygen sensing in living tissue where its metabolism is intimately linked with oxygen metabolism. Regulation of redox balance of labile iron species to prevent the generation of iron-catalyzed reactive oxygen species (ROS) is critical to survival. However, studies on the redox homeostasis of iron species are challenging because of a lack of a redox-state-specific detection method for iron, in particular, labile Fe 2+ . In this study, a universal fluorogenic switching system is established, which is responsive to Fe 2+ ion based on a unique N-oxide chemistry in which dialkylarylamine N-oxide is selectively deoxygenized by Fe 2+ to generate various fluorescent probes of Fe 2+ -CoNox-1 (blue), FluNox-1 (green), and SiRhoNox-1 (red). All the probes exhibited fluorescence enhancement against Fe 2+ with high selectivity both in cuvette and in living cells. Among the probes, SiRhoNox-1 showed an excellent fluorescence response with respect to both reaction rate and off/on signal contrast. Imaging studies were performed showing the intracellular redox equilibrium shift towards labile iron in response to reduced oxygen tension in living cells and 3D tumor spheroids using SiRhoNox-1, and it was found that the hypoxia induction of labile Fe 2+ is independent of iron uptake, hypoxia-induced signaling, and hypoxia-activated enzymes. The present studies demonstrate the feasibility of developing sensitive and specific fluorescent probes for Fe 2+ with refined photophysical characteristics that enable their broad application in the study of iron in various physiological and pathological conditions.

A Numerical Approach and Comparison of Cutting Forces and Chip Morphology in Orthogonal Cutting of Light Alloys

International Nuclear Information System (INIS)

Alvarez, Roberto; Domingo, Rosario; Sebastian, Miguel Angel

2011-01-01

This paper deals with the simulation of UNS A92024 aluminium alloy cutting processes. In particular, 2D and 3D Finite Element Method (FEM) simulations were carried out in order to estimate cutting forces and chip morphology during turning operations. The material is modelled with two different set of parameters for the Johnson--Cook's (J-C) constitutive equation and a failure Cockroft and Latham's model exploited considers damage. The comparison between the predicted chip morphology and principal cutting forces at varying of J-C parameters and cutting regimes with those experimentally found are presented and discussed. The paper shows the importance of damage criterion in the cutting forces, during the simulation, especially in 3D.

Laser cutting of sheets for Tailored Blanks

DEFF Research Database (Denmark)

Bagger, Claus; Olsen, Flemming Ove

1999-01-01

sound welds. Laser cutting the sheets may therefore be an alternative to shear cutting, if the cut kerf squareness can be kept below 0.05 mm.In a number of systematic laboratory experiments the effects of the major process parameters in laser cutting have been investigated. Each cut was quantified...... by the squareness, the surface roughness and the burr height. Mild steel as well as high strength steel with and with out galvanisation with thickness' of 0.7(5) and 1.25 were used.In the tests the difference in cut quality between a 5" and a 7.5" focusing lens were tested and the effect of using pulsed mode laser...

Cutting prepregs, cutting and processing polymer plastics in the manufacture of airсraft panels

OpenAIRE

MELUKHOV NIKITA; GRISHCHENKO TATIANA; LYUBUSHKIN VADIM

2017-01-01

The article presents an alternative to the solution of the problem of reduction of manual operations in manufacture. It may be achieved if cutting out prepregs and processing polymeric materials (PMP) be changed for sharp ultrasonic cutting when manufacturing components from polymeric composite materials (PCM). Described are the lines of investigations on new techniques of cutting out prepreg and processings polymeric material of the Nomex type with the use of the energy of ultrasonic waves. ...

Semantic Versus Syntactic Cutting Planes

OpenAIRE

Filmus, Yuval; Hrubeš, Pavel; Lauria, Massimo

2016-01-01

In this paper, we compare the strength of the semantic and syntactic version of the cutting planes proof system. First, we show that the lower bound technique of Pudlák applies also to semantic cutting planes: the proof system has feasible interpolation via monotone real circuits, which gives an exponential lower bound on lengths of semantic cutting planes refutations. Second, we show that semantic refutations are stronger than syntactic ones. In particular, we give a formula for whic...

21 CFR 882.4275 - Dowel cutting instrument.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

High speed laser cutting machine. Kosoku reza kakoki

Energy Technology Data Exchange (ETDEWEB)

Shinno, N. (Matsushita Electric Industrial Co. Ltd., Kadoma, Osaka (Japan))

1993-11-01

The carbon dioxide gas laser cutting machine is being used widely for from cutting soft steel and stainless steel, etc. to intermetallic welding and in the field of cutting in particular, concerning sheet cutting, it has been changing the existing monopoly of the turret punch press, and as for medium and thick plate cutting, that of the gas plasma fusing device. This article is the general description of high speed laser cutting machine. Concerning the laser cutting (sheet cutting in particular), as the essential items for securing severe cutting accuracy and, at the same time, improving the cutting speed, the following matters are picked up for respective explanation; improvement of stationary machine accuracy, improvement of dynamic machine accuracy, improvement of quality of laser beam as well as optimization of cutting conditions, and shortening of piercing time. Also explanation is given to the respective items, namely speeding-up of medium and thick plate cutting, and reduction of load onto the operator by improved operation. Finally, feeding and removing of a sheet only, and feeding and removing with a pallet are mentioned as the efforts for automation and energy saving. 3 figs., 1 tab.

On the Labile Memory Buffer in the Attentional Blink: Masking the T2 Representation by Onset Transients Mediates the AB

Science.gov (United States)

Jannati, Ali; Spalek, Thomas M.; Di Lollo, Vincent

2011-01-01

Report of a second target (T2) is impaired when presented within 500 ms of the first (T1). This attentional blink (AB) is known to cause a delay in T2 processing during which T2 must be stored in a labile memory buffer. We explored the buffer's characteristics using different types of masks after T2. These characteristics were inferred by…

Improving rooting uniformity in rose cuttings

NARCIS (Netherlands)

Telgen, van H.J.; Eveleens-Clark, B.A.; Garcia Victoria, N.

2007-01-01

Studies to improve rooting uniformity of single node stem cuttings for rose are reported. We found that the variation in shoot growth in a young rose crop depended on the variation in root number of the cuttings, which, in turn, was related to the auxin concentration applied to the cutting before

Formulation of enterosoluble microparticles for an acid labile protein.

Science.gov (United States)

Alavi, Ahmed Kashif; Squillante, Emilio; Mehta, Ketan A

2002-01-01

A microencapsulation method that preserves the activity of an acid labile protein was developed. Solvent evaporation technique that employed ICH class 2 and 3 solvents methanol and acetone, respectively to dissolve pH-sensitive Eudragit polymers was investigated. Total protein released and lactase activities were measured using the USP method A for enteric cores and optimized with respect to process parameters. The percentage yields and entrapment efficiencies were directly proportional to solid content. The mean percentage yield and entrapment efficiency of selected sample was 84 +/- 0.9% and 88 +/- 0.7%, respectively. The residual specific activity of lactase in the selected sample was 89% +/- 0.8 with a net activity loss of 2 +/- 0.28% and 4 +/- 0.52% under ambient and stressed storage, respectively. Dibutyl sebacate levels, lower processing temperatures and lower processing speeds were influential in modulating enzyme activity. The most important formulation factor affecting lactase stability was Eudragit type, followed in decreasing order by processing temperature, processing speed, and solid percentage. Reliable control of lactase release was achieved by microencapsulating the enzyme with pH-sensitive Eudragit L and S enteric polymers using either acetone- or methanol-based solvent but lactase activity was preserved only in acetone-based formulations.

Underwater laser cutting of metal structures

Energy Technology Data Exchange (ETDEWEB)

Alfille, J.P.; Prunele, D. de [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Direction des Technologies Avancees; Pilot, G. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Dept. de Protection de l`Environnement et des Installations; Fredrick, P.; Ramaswami, V.S.; Muys, P. [Radius Engineering, Gent (Belgium)

1994-12-31

Cutting tests were carried out on stainless steel (304L) in air and under 7 meters of water (application to reactor pools), using CO{sub 2} and YAG lasers; results concerned cutting speed, quality of cut, cutting thickness. By-products of sectioning operations using a CO{sub 2} laser were studied: dross, aerosols, suspended particles in water, gas analysis, chemical analysis of the aerosols. Same measurements are currently being taken in the case of the YAG laser with beam transported via optical fiber. (from author). 16 figs., 2 tabs., 3 refs.

Underwater laser cutting of metal structures

International Nuclear Information System (INIS)

Alfille, J.P.; Prunele, D. de

1994-01-01

Cutting tests were carried out on stainless steel (304L) in air and under 7 meters of water (application to reactor pools), using CO 2 and YAG lasers; results concerned cutting speed, quality of cut, cutting thickness. By-products of sectioning operations using a CO 2 laser were studied: dross, aerosols, suspended particles in water, gas analysis, chemical analysis of the aerosols. Same measurements are currently being taken in the case of the YAG laser with beam transported via optical fiber. (from author). 16 figs., 2 tabs., 3 refs

The Effect of Muscle Fiber Direction on the Cut Surface Angle of Frozen Fish Muscular Tissue Cut by Bending Force

OpenAIRE

岡本, 清; 羽倉, 義雄; 鈴木, 寛一; 久保田, 清

1996-01-01

We have proposed a new cutting method named "Cryo-cutting" for frozen foodstuffs by applying a bending force instead of conventional cutting methods with band saw. This paper investigated the effect of muscle fiber angle (θf) to cut surface angle (θs) of frozen tuna muscular tissue at -70, -100 and -130°C for the purpose of evaluating the applicability of the cryo-cutting method to frozen fishes. The results were as follows : (1) There were two typical cutting patterns ("across the muscle fib...

Are the same tapes really the same? Ultrasound study of laser-cut and mechanically cut TVT-O post-operative behavior.

Science.gov (United States)

Rusavy, Zdenek; Masata, Jaromir; Svabik, Kamil; Hubka, Petr; Zvara, Karel; Martan, Alois

2017-11-25

TVT-O production has been modified to laser cutting from mechanical cutting. We compared the behavior of laser and mechanically cut tension-free vaginal tape-obturator (TVT-O) using ultrasound at various time points after surgery. This is a retrospective analysis of clinical and ultrasound data from two previously reported randomized controlled trials with TVT-O. Behavior of mechanically cut TVT-O implanted in January 2007 to November 2009 and laser-cut TVT-O implanted in May 2010 to May 2012 was assessed by ultrasound at day 1, the 2nd week, the 3rd month, and the 1st and 2nd years post-operatively. Bladder neck and tape margins positions were described by coordinates in the orthogonal system calculated from polar coordinates. Tape mobility was measured as a change in the upper and lower tape margin position from rest to maximal Valsalva. Comparison of 2-year subjective and objective surgery outcomes was also performed. In total, 68 mechanically cut and 50 laser-cut TVT-Os were implanted. Follow-up data were available from 49 and 45 women respectively. No differences in any baseline characteristics or bladder neck mobility were observed. Significantly lower tape mobility was observed on day 1 and week 2 after mechanically cut TVT-O, although subsequent mobility was comparable to laser-cut TVT-O. The subjective and objective surgery outcomes were comparable. Although without clinical significance, early postoperative behavior of the mechanically cut and laser-cut TVT-O tapes differs. The less stiff, mechanically-cut TVT-O loosens within 2 weeks of implantation, whereas the stiffer, laser-cut TVT-O keeps its tension.

Treatment of PCR products with exonuclease I and heat-labile alkaline phosphatase improves the visibility of combined bisulfite restriction analysis

International Nuclear Information System (INIS)

Watanabe, Kousuke; Emoto, Noriko; Sunohara, Mitsuhiro; Kawakami, Masanori; Kage, Hidenori; Nagase, Takahide; Ohishi, Nobuya; Takai, Daiya

2010-01-01

Research highlights: → Incubating PCR products at a high temperature causes smears in gel electrophoresis. → Smears interfere with the interpretation of methylation analysis using COBRA. → Treatment with exonuclease I and heat-labile alkaline phosphatase eliminates smears. → The elimination of smears improves the visibility of COBRA. -- Abstract: DNA methylation plays a vital role in the regulation of gene expression. Abnormal promoter hypermethylation is an important mechanism of inactivating tumor suppressor genes in human cancers. Combined bisulfite restriction analysis (COBRA) is a widely used method for identifying the DNA methylation of specific CpG sites. Here, we report that exonuclease I and heat-labile alkaline phosphatase can be used for PCR purification for COBRA, improving the visibility of gel electrophoresis after restriction digestion. This improvement is observed when restriction digestion is performed at a high temperature, such as 60 o C or 65 o C, with BstUI and TaqI, respectively. This simple method can be applied instead of DNA purification using spin columns or phenol/chloroform extraction. It can also be applied to other situations when PCR products are digested by thermophile-derived restriction enzymes, such as PCR restriction fragment length polymorphism (RFLP) analysis.

Effects of cutting and maturity on lycopene concentration of fresh-cut tomatoes during storage at different temperatures

NARCIS (Netherlands)

Moreira Lana, M.; Dekker, M.; Linssen, R.F.A.; Kooten, van O.

2005-01-01

To investigate the changes in lycopene concentration of fresh-cut tomato during storage, tomato fruits at different stages of maturity were cut into 7 mm slices and stored at temperatures varying from 2°C to 16°C. To assess the effect of cutting, intact fruit were stored in an additional experiment

Underwater plasma arc cutting

International Nuclear Information System (INIS)

Leautier, R.; Pilot, G.

1991-01-01

This report describes the work done to develop underwater plasma arc cutting techniques, to characterise aerosols from cutting operations on radioactive and non-radioactive work-pieces, and to develop suitable ventilation and filtration techniques. The work has been carried out in the framework of a contract between CEA-CEN Cadarache and the Commission of European Communities. Furthermore, this work has been carried out in close cooperation with CEA-CEN Saclay mainly for secondary emissions and radioactive analysis. The contract started in May 1986 and was completed in December 1988 by a supplementary agreement. This report has been compiled from several progress reports submitted during the work period, contains the main findings of the work and encloses the results of comparative tests on plasma arc cutting

Modified GrabCut for human face segmentation

Directory of Open Access Journals (Sweden)

Dina Khattab

2014-12-01

Full Text Available GrabCut is a segmentation technique for 2D still color images, which is mainly based on an iterative energy minimization. The energy function of the GrabCut optimization algorithm is based mainly on a probabilistic model for pixel color distribution. Therefore, GrabCut may introduce unacceptable results in the cases of low contrast between foreground and background colors. In this manner, this paper presents a modified GrabCut technique for the segmentation of human faces from images of full humans. The modified technique introduces a new face location model for the energy minimization function of the GrabCut, in addition to the existing color one. This location model considers the distance distribution of the pixels from the silhouette boundary of a fitted head, of a 3D morphable model, to the image. The experimental results of the modified GrabCut have demonstrated better segmentation robustness and accuracy compared to the original GrabCut for human face segmentation.

Materials selection for cutting tools

International Nuclear Information System (INIS)

Burkhis, Adel M.

2008-01-01

The selection of proper tool steel for a given application is a difficult task. So; the most important selection factors in choosing cutting tool materials are based on their tool material requirements, cutting tool design and service conditions which is mainly considered as functional requirements. The processability requirements concerns in heat treat ability of the material tool. The classification of these tool materials were discussed with their properties requirement and percent of alloying element which is added to give best properties with a little increase in cost that highly appear in comparison of the selection. The cutting tool materials were evaluated based on two cases; The first was in case of rough surface; the high speed steels is the best material and the other was the ceramic material is the highest performance in cutting of soft or high rate of metal removal. (author)

Edge Cut Domination, Irredundance, and Independence in Graphs

OpenAIRE

Fenstermacher, Todd; Hedetniemi, Stephen; Laskar, Renu

2016-01-01

An edge dominating set $F$ of a graph $G=(V,E)$ is an \\textit{edge cut dominating set} if the subgraph $\\langle V,G-F \\rangle$ is disconnected. The \\textit{edge cut domination number} $\\gamma_{ct}(G)$ of $G$ is the minimum cardinality of an edge cut dominating set of $G.$ In this paper we study the edge cut domination number and investigate its relationships with other parameters of graphs. We also introduce the properties edge cut irredundance and edge cut independence.

Preferences of cut flowers consumers

Directory of Open Access Journals (Sweden)

Sylwia Kierczyńska

2010-01-01

Full Text Available The results of interviews suggest that majority of the cut flowers’ consumers has favourite kind of flower, among which most frequently pointed one was the rose. More than half of the interviewed favour the uniform colour of cut flowers and red colour was the most favourite one. The subtle smell of flowers was the most preferable one but the intensive fragrance was favoured for more consumers than odourless flowers. The data from selected florists’ confirm the information from interviews – in spite of the occasion, roses were the most demanded cut flowers.

Designing for hot-blade cutting

DEFF Research Database (Denmark)

Brander, David; Bærentzen, Jakob Andreas; Clausen, Kenn

2016-01-01

In this paper we present a novel method for the generation of doubly-curved, architectural design surfaces using swept Euler elastica and cubic splines. The method enables a direct design to production workflow with robotic hot-blade cutting, a novel robotic fabrication method under development......-trivial constraints of blade-cutting in a bottom-up fashion, enabling an exploration of the unique architectural potential of this fabrication approach. The method is implemented as prototype design tools in MatLAB, C++, GhPython, and Python and demonstrated through cutting of expanded polystyrene foam design...

Status on underwater plasma arc cutting in KHI, 3

International Nuclear Information System (INIS)

Abe, Tadashi; Aota, Toshiichi; Nishizaki, Tadashi; Nakayama, Shigeru; Yamashita, Seiji

1983-01-01

In Kawasaki Heavy Industries, Ltd., the development of a remote dismantling system by underwater plasma arc cutting process has been advanced, expecting its application to the dismantling and removal of nuclear reactor facilities. In the previous two reports, the fundamental experimental results such as the comparison of the cutting capability in air and in water were shown, but this time, the remote automatic cutting of wedge-shaped specimens was carried out, using a newly installed manipulator for underwater works, therefore its outline is reported. Also the cutting experiment by overhead position and vertical position was performed by using the same equipment, and comparison was made with the cutting capability by downhand and horizontal positions. It is important to grasp the cutting characteristics in the case of upward advancing and downward advancing cuttings by overhead and vertical positions when the cutting of pressure vessels and horizontal pipes into rings is supposed. The experimental apparatus, the cutting conditions, the testing method and the test results of the cutting capability test, the test of changing direction during cutting, and the remote cutting of pipes into rings are described. The underwater plasma arc cutting can cut all metals, the cutting speed is relatively high, and the apparatus is simple and compact. (Kako, I.)

MECHANISMS OF CUTTING BLADE WEAR AND THEIR INFLUENCE ON CUTTING ABILITY OF THE TOOL DURING MACHINING OF SPECIAL ALLOYS

Directory of Open Access Journals (Sweden)

Tomáš Zlámal

2016-09-01

Full Text Available With increased requirements for quality and shelf life of machined parts there is also a higher share of the use of material with specific properties that are identified by the term “superalloys”. These materials differ from common steels by mechanical and physical properties that cause their worse machinability. During machining of “superalloys” worse machinability has negative influence primarily on the amount of cutting edge wear, which shortens durability of the cutting tool. The goal of experimental activity shown in this contribution is to determine individual mechanisms of the cutting edge wear and their effects on the cutting ability during high speed machining of nickel superalloy. A specific exchangeable cutting insert made from cubic boric nitride was used for machining of the 625 material according to ASM 5666F. The criteria to evaluate cutting ability and durability of the cutting tool became selected parameters of surface integrity and quality of the machined surface.

Submerged cutting characteristics of abrasive suspension jet

International Nuclear Information System (INIS)

Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroki

2015-01-01

An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

Responses to mild water deficit and rewatering differ among secondary metabolites but are similar among provenances within Eucalyptus species.

Science.gov (United States)

McKiernan, Adam B; Potts, Brad M; Brodribb, Timothy J; Hovenden, Mark J; Davies, Noel W; McAdam, Scott A M; Ross, John J; Rodemann, Thomas; O'Reilly-Wapstra, Julianne M

2016-02-01

Water deficit associated with drought can severely affect plants and influence ecological interactions involving plant secondary metabolites. We tested the effect of mild water deficit and rewatering on physiological, morphological and chemical traits of juvenile Eucalyptus globulus Labill. and Eucalyptus viminalis Labill. We also tested if responses of juvenile eucalypts to water deficit and rewatering varied within species using provenances across a rainfall gradient. Both species and all provenances were similarly affected by mild water deficit and rewatering, as only foliar abscisic acid levels differed among provenances during water deficit. Across species and provenances, water deficit decreased leaf water potential, above-ground biomass and formylated phloroglucinol compound concentrations, and increased condensed tannin concentrations. Rewatering reduced leaf carbon : nitrogen, and total phenolic and chlorogenic acid concentrations. Water deficit and rewatering had no effect on total oil or individual terpene concentrations. Levels of trait plasticity due to water deficit and rewatering were less than levels of constitutive trait variation among provenances. The overall uniformity of responses to the treatments regardless of native provenance indicates limited diversification of plastic responses when compared with the larger quantitative variation of constitutive traits within these species. These responses to mild water deficit may differ from responses to more extreme water deficit or to responses of juvenile/mature eucalypts growing at each locality. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Ann modeling of kerf transfer in Co2 laser cutting and optimization of cutting parameters using monte carlo method

Directory of Open Access Journals (Sweden)

Miloš Madić

2015-01-01

Full Text Available In this paper, an attempt has been made to develop a mathematical model in order to study the relationship between laser cutting parameters such as laser power, cutting speed, assist gas pressure and focus position, and kerf taper angle obtained in CO2 laser cutting of AISI 304 stainless steel. To this aim, a single hidden layer artificial neural network (ANN trained with gradient descent with momentum algorithm was used. To obtain an experimental database for the ANN training, laser cutting experiment was planned as per Taguchi’s L27 orthogonal array with three levels for each of the cutting parameters. Statistically assessed as adequate, ANN model was then used to investigate the effect of the laser cutting parameters on the kerf taper angle by generating 2D and 3D plots. It was observed that the kerf taper angle was highly sensitive to the selected laser cutting parameters, as well as their interactions. In addition to modeling, by applying the Monte Carlo method on the developed kerf taper angle ANN model, the near optimal laser cutting parameter settings, which minimize kerf taper angle, were determined.

The effects of cutting parameters on cutting forces and heat generation when drilling animal bone and biomechanical test materials.

Science.gov (United States)

Cseke, Akos; Heinemann, Robert

2018-01-01

The research presented in this paper investigated the effects of spindle speed and feed rate on the resultant cutting forces (thrust force and torque) and temperatures while drilling SawBones ® biomechanical test materials and cadaveric cortical bone (bovine and porcine femur) specimens. It also investigated cortical bone anisotropy on the cutting forces, when drilling in axial and radial directions. The cutting forces are only affected by the feed rate, whereas the cutting temperature in contrast is affected by both spindle speed and feed rate. The temperature distribution indicates friction as the primary heat source, which is caused by the rubbing of the tool margins and the already cut chips over the borehole wall. Cutting forces were considerably higher when drilling animal cortical bone, in comparison to cortical test material. Drilling direction, and therewith anisotropy, appears to have a negligible effect on the cutting forces. The results suggest that this can be attributed to the osteons being cut at an angle rather than in purely axial or radial direction, as a result of a twist drill's point angle. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Evaluation of cutting force uncertainty components in turning

DEFF Research Database (Denmark)

Axinte, Dragos Aurelian; Belluco, Walter; De Chiffre, Leonardo

2000-01-01

A procedure is proposed for the evaluation of those uncertainty components of a single cutting force measurement in turning that are related to the contributions of the dynamometer calibration and the cutting process itself. Based on an empirical model including errors form both sources......, the uncertainty for a single measurement of cutting force is presented, and expressions for the expected uncertainty vs. cutting parameters are proposed. This approach gives the possibility of evaluating cutting force uncertainty components in turning, for a defined range of cutting parameters, based on few...

Identification of the critical depth-of-cut through a 2D image of the cutting region resulting from taper cutting of brittle materials

Science.gov (United States)

Gu, Wen; Zhu, Zhiwei; Zhu, Wu-Le; Lu, Leyao; To, Suet; Xiao, Gaobo

2018-05-01

An automatic identification method for obtaining the critical depth-of-cut (DoC) of brittle materials with nanometric accuracy and sub-nanometric uncertainty is proposed in this paper. With this method, a two-dimensional (2D) microscopic image of the taper cutting region is captured and further processed by image analysis to extract the margin of generated micro-cracks in the imaging plane. Meanwhile, an analytical model is formulated to describe the theoretical curve of the projected cutting points on the imaging plane with respect to a specified DoC during the whole cutting process. By adopting differential evolution algorithm-based minimization, the critical DoC can be identified by minimizing the deviation between the extracted margin and the theoretical curve. The proposed method is demonstrated through both numerical simulation and experimental analysis. Compared with conventional 2D- and 3D-microscopic-image-based methods, determination of the critical DoC in this study uses the envelope profile rather than the onset point of the generated cracks, providing a more objective approach with smaller uncertainty.

Cutting tool for removing materials from well bore

International Nuclear Information System (INIS)

Lynde, G.D.; Harvey, H.H. Jr.

1991-01-01

This patent describes a cutting tool adapted to be positioned downhole in a well bore for removing a metal member from the well bore; a tool body adapted to be received within said well bore and to be supported at its upper end for rotation about a longitudinal axis; blades at spaced intervals on the body and extending outwardly therefrom, each of the blades having a base with a leading surface relative to the direction of rotation; closely spaced cutting elements of hard cutting material secured to said leading surface of the base in a plurality of transversely extending rows, each cutting element being of a predetermined size and shape and arranged in a predetermined generally symmetrical pattern on the base relative to the other elements, each of said cutting elements having an exposed from cutting face forming a cutting surface, a rear face secured to the leading surface of said base, a peripheral surface extending between said faces, and a relatively sharp edge formed at the juncture of the front face and peripheral surface; the front cutting face of each cutting element being arranged and constructed for directing an extending end portion of a turning cut form said member to effect a breaking of said turning from the member being cut in a predetermined manner to minimize interesting of the turning

Craterlike structures on the laser cut surface

Science.gov (United States)

Shulyatyev, V. B.; Orishich, A. M.

2017-10-01

Analysis of the laser cut surface morphology remain topical. It is related with the fact that the surface roughness is the main index of the cut quality. The present paper deals with the experimental study of the relatively unstudied type of defects on the laser cut surface, dimples, or craters. According to the measurement results, amount of craters per unit of the laser cut surface area rises as the sheet thickness rises. The crater diameter rises together with the sheet thickness and distance from the upper sheet edge. The obtained data permit concluding that the defects like craters are observed predominantly in the case of thick sheets. The results agree with the hypothesis of crater formation as impact structures resulting from the melt drops getting on the cut channel walls upon separation from the cut front by the gas flow.

The Gesso Cut for Printmaking

Science.gov (United States)

Kelly, Perry; Sarvis, Alva

1969-01-01

Directions are given for the preparation, cutting, and printing of a gesso board. A gesso cut is defined as a board coated with gesso into which a design has been impressed. The process is similar to the woodcut, but offers greater textural possibilities. (BF)

Laser cutting of Kevlar laminates

Energy Technology Data Exchange (ETDEWEB)

VanCleave, R.A.

1977-09-01

An investigation has been conducted of the use of laser energy for cutting contours, diameters, and holes in flat and shaped Kevlar 49 fiber-reinforced epoxy laminates as an alternate to conventional machining. The investigation has shown that flat laminates 6.35 mm thick may be cut without backup by using a high-powered (1000-watt) continuous wave CO/sub 2/ laser at high feedrates (33.87 mm per second). The cut produced was free of the burrs and delaminations resulting from conventional machining methods without intimate contact backup. In addition, the process cycle time was greatly reduced.

Investigation of cutting-induced damage in CMC bend bars

Directory of Open Access Journals (Sweden)

Neubrand A.

2015-01-01

Full Text Available Ceramic matrix composites (“CMC” with a strong fibre-matrix interface can be made damage-tolerant by introducing a highly porous matrix. Such composites typically have only a low interlaminar shear strength, which can potentially promote damage when preparing specimens or components by cutting. In order to investigate the damage induced by different cutting methods, waterjet cutting with and without abrasives, laser-cutting, wire eroding and cutoff grinding were used to cut plates of two different CMCs with a matrix porosity up to 35 vol.-%. For each combination of cutting method and composite, the flexural and interlaminar shear strength of the resulting specimens was determined. Additionally, the integrity of the regions near the cut surfaces was investigated by high-resolution x-ray computer tomography. It could be shown that the geometrical quality of the cut is strongly affected by the cutting method employed. Laser cut and waterjet cut specimens showed damage and delaminations near the cut surface leading to a reduced interlaminar shear strength of short bend bars in extreme cases.

Temporal Changes in Photochemically Labile DOM and Implications for Carbon Budgets in Peatland Aquatic Systems

Science.gov (United States)

Pickard, A.

2015-12-01

Aquatic systems in peatland catchments are subject to high loading of dissolved organic matter (DOM) from surrounding terrestrial environments. However the significance of photochemical transformation of DOM in peatland carbon budgets remains poorly constrained. In this study UV irradiation experiments were conducted on water samples collected over one year from two contrasting systems in Scotland: a stream draining a peatland with high levels of DOM and a reservoir draining a peat catchment with low levels of DOM. Further samples were collected from the high DOM system during two storm events. After experimental exposure, optical and chemical analyses were employed to determine photochemical lability of the DOM pool. At both sites irradiation-induced decreases in dissolved organic carbon (DOC) as a percentage of the total carbon pool were greatest in winter, suggesting that DOM was depleted in photo-reactive molecules in summer. Seasonal variability in DOC was high at the stream site and was positively correlated with CO₂ and CO photoproduction (r2 = 0.81 and 0.83, respectively; pLignin phenol analyses indicate considerable contribution of peat to the DOM pool at the stream site, particularly during summer. Whilst DOC concentrations did not vary greatly during storm events, UV-Vis absorbance indicators did, signifying changing DOM source material from activation of different hydrological pathways. The most photo-reactive DOM occurred 5-10 hours after peak discharge, suggesting that storms replenish photochemically labile DOM in headwater streams. Conservative estimates using data from this study suggest that up to 7% of the DOM pool of peatland streams can be lost (primarily as CO₂ and CO) upon exposure to 8 hours of environmentally representative UV irradiation. Further investigation in field campaigns under natural UV exposure are underway to assess the importance of photodegradation of DOM as a loss pathway of carbon based gases from aquatic systems.

Investigation of Cutting Quality of Remote DOE Laser Cutting in 0.5 mm Stainless Steel

Science.gov (United States)

Villumsen, Sigurd Lazic; Kristiansen, Morten

It has previously been shown that the stability of the remote fusion cutting (RFC) process can be increased by modifying the intensity profile of the laser by means of a diffractive optical element (DOE). This paper investigates the quality of remote DOE cutting (RDC) conducted with a 3 kW single mode fiber laser in 0.5 mm stainless steel. An automatic measurement system is used to investigate how the travel speed, focus offset and angle of incidence effect the kerf width and kerf variance. The study shows that the RDC process has a very low kerf width variance, and that the kerf width decreases with cutting speed. Furthermore, selected etched samples show a significant increase in the perpendicularity of the cuts when compared to RFC. Also, on average, the depth of the layer of molten material for RFC is 83% deeper than for RDC.

Effet de l'hybridation interspecifique sur la teneur et la composition chimique des huiles essentielles d'eucalyptus cultivés au Maroc

OpenAIRE

Farah A.; Fechtal M.; Chaouch A.

2002-01-01

Interspecific hybridization effect on the content and the chemical composition of essential oils of eucalyptus grown in Morocco. In this work, the quality and quantity of the leave essential oils of five Eucalyptus hybrids were determined. The crosses of Eucalyptus globulus ssp. maideni, Eucalyptus globulus ssp. globulus, Eucalyptus grandis, Eucalyptus cladocalyx and Eucalyptus diversicolor with Eucalyptus camaldulensis have been studied. The average yield of parental species samples varies a...

High precision tungsten cutting for optics

International Nuclear Information System (INIS)

Reglero, V.; Velasco, T.; Rodrigo, J.; Gasent, L.J.; Alamo, J.; Chato, R.; Ruiz Urien, I.; Santos, I.; Zarauz, J.; Clemente, G.; Sanz-Tudanca, C.; Lopez, J.L.

2001-01-01

The results obtained during the INTEGRAL masks development program an implementing the HURA and MURA codes on tungsten plates of different thickness are presented. Hard scientific requirements on pixels size and location tolerances (tenths of microns over large areas -1 m 2 - and thickness from 0.5 mm to 60 mm) required the set up of a dedicated program for testing cutting technologies: laser, photochemical milling, spark machining and electro discharge wire cutting. After a very intensive test campaign the wire cutting process was selected as the optimum technology for code manufacturing . Accuracies achieved an the code cutting fulfill scientific requirements. In fact, they are 5 times better than required. Pixel size and centroids location accuracies of 0.01 mm over a 1 m 2 area have been obtained for the 10,000 pixels on IBIS, 100 pixels on SPI and 24000 pixels on JEM-X masks. Comparative results among different cutting technologies are also discussed. (author)

Development of laser cutting method for stainless steel liner

International Nuclear Information System (INIS)

Ishihara, Satoshi; Takahata, Masato; Wignarajah, Sivakumaran; Kamata, Hirofumi

2007-01-01

The present work is an attempt to develop a laser cutting method for cutting and removing stainless steel liners from concrete walls and floors in nuclear facilities. The effect of basic laser cutting parameters such as energy, cutting speed, assist gas flow etc. were first studied through cutting experiments on mock-up concrete specimens lined with 3mm thick stainless steel sheets using a 1kW Nd:YAG laser. These initial studies were followed by further studies on the effect of unevenness of the liner surface and on a new method of confining contamination during the cutting process using a sliding evacuation hood attached to the laser cutting head. The results showed that laser cutting is superior to other conventional cutting methods from the point of view of safety from radioactivity and work efficiency when cutting contaminated stainless steel liners. (author)

Regge cuts: A general approach

International Nuclear Information System (INIS)

Weis, J.H.

1976-01-01

We discuss an approach to the calculation of Regge-cut contributions to scattering amplitudes which relies only on the general structure of the physical Reggeon couplings. It thus allows a unified treatment of disparate models [such as the Feynman (Mandelstam) graph model and the dual model] and a general derivation of the Abramovskii--Gribov--Kancheli (AGK) rules. The structure of the Reggeon couplings is expressed through integrals over complex helicity. The Regge-cut amplitude can then be obtained, and its s-channel discontinuity, taken; there results a direct derivation of a set of ''cutting rules'' which express the total discontinuity as a sum of terms involving various discontinuities of the Reggeon couplings. The equality of these discontinuities follows directly if the singularities in complex helicity are the usual ones. Thus the AGK rules are seen to be quite model independent. Here we study in detail the simplest example: the Reggeon-particle cut in the four-particle amplitude

Why I like power cuts...

CERN Multimedia

Computer Security Team

2012-01-01

Accidental power cuts - a permanent nuisance when running accelerators or computing services, since it takes a lot of time to recover from them. While I feel very sorry for those who are under pressure to get their service running again and deeply regret the loss of down-time and availability, I must admit that I like power cuts: power cuts make computers reboot! And rebooting computers at CERN means all the pending software patches are automatically applied.   But don’t think I am egotistic enough to endorse power cuts. Not necessarily! I am already happy if you regularly patch your computer(s) yourself, where regularly means at least once a month: · If you run a centrally or locally managed Windows computer, give that small orange blinking “CMF” icon in the taskbar a chance in the evening to apply all the pending patches. Also, let it initiate a reboot at the end! · If you have a personal computer with your own Windows operating system, ...

Method of dismantling cylindrical structure by cutting

International Nuclear Information System (INIS)

Harada, Minoru; Mitsuo, Kohei; Yokota, Isoya; Nakamura, Kenjiro.

1989-01-01

This invention concerns a method of cutting and removing cylindrical structures, for example, iron-reinforced concrete materials such as thermal shielding walls in BWR type power plants into block-like form. That is, in a method of cutting and removing the cylindrical structure from the side of the outer wall, the structural material is cut from above to below successively in the axial direction and the circumferential direction by means abrasive jet by remote operation and cut into blocks each of a predetermined size. The cut out blocks are successively taken out. Cutting of the material from above to below by remote operation and taking out of small blocks causes no hazards to human body. Upon practicing the present invention, it is preferred to use a processing device for slurry and exhaust gases for preventing scattering of activated dismantled pieces or powdery dusts. (K.M.)

Photodiode-based cutting interruption sensor for near-infrared lasers.

Science.gov (United States)

Adelmann, B; Schleier, M; Neumeier, B; Hellmann, R

2016-03-01

We report on a photodiode-based sensor system to detect cutting interruptions during laser cutting with a fiber laser. An InGaAs diode records the thermal radiation from the process zone with a ring mirror and optical filter arrangement mounted between a collimation unit and a cutting head. The photodiode current is digitalized with a sample rate of 20 kHz and filtered with a Chebyshev Type I filter. From the measured signal during the piercing, a threshold value is calculated. When the diode signal exceeds this threshold during cutting, a cutting interruption is indicated. This method is applied to sensor signals from cutting mild steel, stainless steel, and aluminum, as well as different material thicknesses and also laser flame cutting, showing the possibility to detect cutting interruptions in a broad variety of applications. In a series of 83 incomplete cuts, every cutting interruption is successfully detected (alpha error of 0%), while no cutting interruption is reported in 266 complete cuts (beta error of 0%). With this remarkable high detection rate and low error rate, the possibility to work with different materials and thicknesses in combination with the easy mounting of the sensor unit also to existing cutting machines highlight the enormous potential for this sensor system in industrial applications.

Users' manual for fault tree analysis code: CUT-TD

International Nuclear Information System (INIS)

Watanabe, Norio; Kiyota, Mikio.

1992-06-01

The CUT-TD code has been developed to find minimal cut sets for a given fault tree and to calculate the occurrence probability of its top event. This code uses an improved top-down algorithm which can enhance the efficiency in deriving minimal cut sets. The features in processing techniques incorporated into CUT-TD are as follows: (1) Consecutive OR gates or consecutive AND gates can be coalesced into a single gate. As a result, this processing directly produces cut sets for the redefined single gate with each gate not being developed. (2) The independent subtrees are automatically identified and their respective cut sets are separately found to enhance the efficiency in processing. (3) The minimal cut sets can be obtained for the top event of a fault tree by combining their respective minimal cut sets for several gates of the fault tree. (4) The user can reduce the computing time for finding minimal cut sets and control the size and significance of cut sets by inputting a minimum probability cut off and/or a maximum order cut off. (5) The user can select events that need not to be further developed in the process of obtaining minimal cut sets. This option can reduce the number of minimal cut sets, save the computing time and assists the user in reviewing the result. (6) Computing time is monitored by the CUT-TD code so that it can prevent the running job from abnormally ending due to excessive CPU time and produce an intermediate result. The CUT-TD code has the ability to restart the calculation with use of the intermediate result. This report provides a users' manual for the CUT-TD code. (author)

Monitoring machining conditions by analyzing cutting force vibration

Energy Technology Data Exchange (ETDEWEB)

Piao, Chun Guang; Kim, Ju Wan; Kim, Jin Oh; Shin, Yoan [Soongsl University, Seoul (Korea, Republic of)

2015-09-15

This paper deals with an experimental technique for monitoring machining conditions by analyzing cutting-force vibration measured at a milling machine. This technique is based on the relationship of the cutting-force vibrations with the feed rate and cutting depth as reported earlier. The measurement system consists of dynamic force transducers and a signal amplifier. The analysis system includes an oscilloscope and a computer with a LabVIEW program. Experiments were carried out at various feed rates and cutting depths, while the rotating speed was kept constant. The magnitude of the cutting force vibration component corresponding to the number of cutting edges multiplied by the frequency of rotation was linearly correlated with the machining conditions. When one condition of machining is known, another condition can be identified by analyzing the cutting-force vibration.

Monitoring machining conditions by analyzing cutting force vibration

International Nuclear Information System (INIS)

Piao, Chun Guang; Kim, Ju Wan; Kim, Jin Oh; Shin, Yoan

2015-01-01

This paper deals with an experimental technique for monitoring machining conditions by analyzing cutting-force vibration measured at a milling machine. This technique is based on the relationship of the cutting-force vibrations with the feed rate and cutting depth as reported earlier. The measurement system consists of dynamic force transducers and a signal amplifier. The analysis system includes an oscilloscope and a computer with a LabVIEW program. Experiments were carried out at various feed rates and cutting depths, while the rotating speed was kept constant. The magnitude of the cutting force vibration component corresponding to the number of cutting edges multiplied by the frequency of rotation was linearly correlated with the machining conditions. When one condition of machining is known, another condition can be identified by analyzing the cutting-force vibration

Estudo da labilidade de Cu(II, Cd(II, Mn(II e Ni(II em substâncias húmicas aquáticas utilizando-se membranas celulósicas organomodificadas Lability study of Cu(II, Cd(II, Mn(II and Ni(II complexed by aquatic humic substances using organomodified cellulose membranes

Directory of Open Access Journals (Sweden)

André Henrique Rosa

2007-02-01

Full Text Available In this work commercial filters papers were organomodified with tetraethylorthosilicate (TEOS and 3-aminopropyltriethoxysilane (3-APTS, aiming at the development of a new analytical procedure for in-situ speciation of labile and inert metal species in aquatic systems. Parameters that exert influence on the metal lability such as pH, chelating time, concentration and characteristics of the organic matter were studied in the laboratory using tests for metal recuperation. The results showed slower kinetics for Cu ion than for Ni, Mn and Cd in the absence of aquatic humic substances (AHS. The relative lability observed for complexed metals in aquatic humic substances using organomodified filter papers was Cu>>Cd>Ni>Mn. The pH values, structural characteristics and concentration of AHS exert strong influence on the lability of the metals. The results obtained showed that the utilization of organomodified filter papers can be an interesting and promising alternative for in situ characterization of metal lability in aquatic systems.

Predicción bayesiana de parámetros genéticos en clones de Eucalyptus globulus bajo condiciones de suplemento hídrico

Directory of Open Access Journals (Sweden)

Freddy Mora

2013-01-01

Full Text Available Se realizó un análisis Bayesiano de parámetros genéticos del crecimiento en 29 clones de Eucalyptus globulus de doce meses de edad, en el sur de Chile. Se consideraron dos condiciones ambientales contrastantes en cuanto a la disponibilidad hídrica: 1. Sin irrigación, y 2. Las plantas se irrigaron con un sistema localizado de riego. Para el análisis Bayesiano se utilizó el algoritmo de Gibbs en un modelo de interacción clonambiente. Los valores de heredabilidad fueron altos en la condición de riego (moda a posteriori de H^2=0,41, 0,36 y 0,39 para la altura, diámetro y área basal, respectivamente, en tanto que en la situación sin riego, los valores de las heredabilidades fueron significativamente más bajos; confirmado por medio de los intervalos de credibilidad Bayesianos (95 % de probabilidad. La moda a posteriori de la correlación genética entre sitios fue positiva y alta para las tres características (r=0,7, 0,65 y 0,8, para altura, diámetro y área basal, respectivamente, y de acuerdo al intervalo de credibilidad, esta correlación fue estadísticamente diferente de cero, indicando una interacción no significativa.

Melt Flow and Energy Limitation of Laser Cutting

Directory of Open Access Journals (Sweden)

Pavel Hudeček

2016-01-01

Full Text Available Laser technology is a convertible technology for plenty of parts in most materials. Laser material processing for industrial manufacturing applications is today a widespread procedure for welding, cutting, marking and micro machining of metal and plastic parts and components. Involvement and support this huge mass-production industry of laser cutting, new technology and dry-process using lasers were and are being actively developed. Fundamentally, industrial laser cutting or other applications on industry should satisfy the four key practical application issues including “Quality or Performance”, “Throughput or Speed”, “Cost or Total Ownership Cost”, and “Reliability”. Laser requires for examples several complicated physical factors to be resolved including die strength to be enable good wire-bonding and survival of severe cycling test, clean cutting wall surface, good cutting of direct attach film, and proper speed of cutting for achieving economy of throughput. Some example of maximum cutting rate, wherewith is normally limited laser energy, cutting speed is depend on type laser, different of cutting with one laser beam and beam pattern and applied laser power/material thickness will be introduced in this paper.

Feasibility Study of Cryogenic Cutting Technology by Using a Computer Simulation and Manufacture of Main Components for Cryogenic Cutting System

International Nuclear Information System (INIS)

Kim, Sung Kyun; Lee, Dong Gyu; Lee, Kune Woo; Song, Oh Seop

2009-01-01

Cryogenic cutting technology is one of the most suitable technologies for dismantling nuclear facilities due to the fact that a secondary waste is not generated during the cutting process. In this paper, the feasibility of cryogenic cutting technology was investigated by using a computer simulation. In the computer simulation, a hybrid method combined with the SPH (smoothed particle hydrodynamics) method and the FE (finite element) method was used. And also, a penetration depth equation, for the design of the cryogenic cutting system, was used and the design variables and operation conditions to cut a 10 mm thickness for steel were determined. Finally, the main components of the cryogenic cutting system were manufactures on the basis of the obtained design variables and operation conditions.

Comparison of blood loss between using non central part cutting knee prosthesis and distal central part cutting.

Science.gov (United States)

Malairungsakul, Anan

2014-12-01

Patients who undergo knee replacement surgery may need to receive a blood transfusion due to blood loss during the operation. Therefore it was important to improve the design of knee implant operative procedures in an attempt to reduce the rate of blood loss. The present study aimed to compare the blood loss between two types of knee replacement surgery. This is a retrospective study in which 78 patients received cemented knee replacements in Phayao Hospital between October 2010 and March 2012. There were two types of surgical procedure: 1) using an implant position covering the end of the femoral bone without cutting into the central part of the distal femoral, 2) using an implant position covering the end of the femoral bone cutting the central part of the distal femoral. Blood loss, blood transfusion, hemoglobin and hematocrit were recorded preoperatively, immediately postsurgery and 48 hours after surgery. Findings revealed that the knee replacement surgery using the implant position covering the end of the femoral bone without cutting the central part of the distal femoral significantly lowered the rate of blood loss when compared to using the implant position covering the end of the femoral bone with central cutting of the distal femor. The average blood loss during the operation without cutting at the central part of distal femoral was 49.50 ± 11.11 mL; whereas the operation cutting the central part of the distal femoral was 58.50 ± 11.69 mL. As regards blood loss, the knee replacement surgery using the implant position covering the end ofthefemoral bone without cutting the central part of distal femor was better than using the implant position covering the end of the femoral bone cutting at the central part of the distal femor.

Stress-induced resistance to the fear memory labilization/reconsolidation process. Involvement of the basolateral amygdala complex.

Science.gov (United States)

Espejo, Pablo Javier; Ortiz, Vanesa; Martijena, Irene Delia; Molina, Victor Alejandro

2016-10-01

Consolidated memories can enter into a labile state after reactivation followed by a restabilization process defined as reconsolidation. This process can be interfered with Midazolam (MDZ), a positive allosteric modulator of the GABA-A receptor. The present study has evaluated the influence of prior stress on MDZ's interfering effect. We also assessed the influence of both systemic and intra-basolateral amygdala (BLA) infusion of d-cycloserine (DCS), a partial agonist of the NMDA receptors, on the MDZ effect in previously stressed rats. Furthermore, we analyzed the effect of stress on the expression of Zif-268 and the GluN2B sites, two molecular markers of the labilization/reconsolidation process, following reactivation. The results revealed that prior stress resulted into a memory trace that was insensitive to the MDZ impairing effect. Both systemic and intra-BLA DCS administration previous to reactivation restored MDZ's disruptive effect on memory reconsolidation in stressed animals. Further, reactivation enhanced Zif-268 expression in the BLA in control unstressed rats, whereas no elevation was observed in stressed animals. In agreement with the behavioral findings, DCS restored the increased level of Zif-268 expression in the BLA in stressed animals. Moreover, memory reactivation in unstressed animals elevated GluN2B expression in the BLA, thus suggesting that this effect is involved in memory destabilization, whereas stressed animals did not reveal any changes. These findings are consistent with resistance to the MDZ effect in these rats, indicating that stress exposure prevents the onset of destabilization following reactivation. In summary, prior stress limited both the occurrence of the reactivation-induced destabilization and restabilization. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization of abiotic stress genes from different species of eucalyptus

International Nuclear Information System (INIS)

Naz, S.; Kausar, H.; Saleem, F.; Zafarullah, A.

2015-01-01

The stresses causing dehydration damage to the plant cell like cold, drought, and high salinity are the most frequent environmental stresses that influence plant growth, development and restraining productivity in cultivated areas world-wide. Many drought, salinity and cold inducible genes causing tolerance to environmental stresses in many plants include Dehydrin1 (DHN1), Dehydrin2 (DHN2), Dehydrin10 (DHN10), putative phosphate transporter (Ecpt2), choline monooxygenase (CMO) and DREB/CBF1c genes. Gene specific primer pairs were designed for each gene using DNAStar software. These genes were amplified from different species of eucalyptus such as Eucalyptus camaldulensis, E. globulus, E. tereticornis and E. gunii through PCR. Dehydrin2 gene of E. camaldulensis and dehydrin10 gene of E. globulus were cloned using the TA Cloning Kit with pCR 2.1 vector and sequenced. The Dehydrin genes sequences were submitted to GeneBank: Eucalyptus globulus dehydrin10 gene (Accession No. HG915712) and E. camaldulensis dehydrin 2 gene (Accession No. HG813113). The amino acid sequence of Dehydrin10 from E. globulus showed 97% homology to E. globulus DHN10 (JN052210) and Dehydrin2 from E. camaldulensis presented 94% homology to E. globulus DHN2 (JN052209). These genes can be employed in generating drought resistant crop plants. (author)

Commissioning a hobby cutting device for radiochromic film preparation.

Science.gov (United States)

Zolfaghari, Somayeh; Francis, Kirby E; Kairn, Tanya; Crowe, Scott B

2017-06-01

In addition to a high spatial resolution and well characterised dose response, one of the major advantages of radiochromic film as a dosimeter is that sheets of film can be cut into pieces suitable for use as calibration films, and for in vivo and phantom measurements. The cutting of film is typically done using scissors or a guillotine, and this process can be time-consuming, limited in precision, requires extensive handling and does not allow holes to be cut from the film without cutting from an existing edge. This study investigated the use of a Brother ScanNCut hobby cutting system for EBT3 film preparation. The optimal operating parameters (blade size, pressure, speed) that resulted in precise cuts with minimal delamination at cut edges were identified using test cutting patterns. These parameters were then used to cut a large film insert for a stereotactic head phantom for comparison against an insert cut with scissors. While the hobby cutting system caused a wider region of delamination at the film edge (1.8 mm) compared to scissors (1 mm), the hobby cutting system was found to be able to produce reproducible cuts more efficiently and more accurately than scissors. The use of the hobby cutting system is recommended for complex phantom inserts (containing sharp corners or holes for alignment rods) or in situations where large numbers of film pieces need to be prepared.

Failure mechanisms of superhard materials when cutting superalloys

International Nuclear Information System (INIS)

Focke, A.E.; Westermann, F.E.; Ermi, A.; Yavelak, J.; Hoch, M.

1975-01-01

The present research studies the reasons for the failure of tungsten carbide tools while cutting superalloys. There is a continuous layer of the superalloy in the bottom of the crater which from time to time is torn away locally, taking tungsten carbide crystal with it. Under recommended cutting conditions a plateau (unworn cutting surface) separates the crater from the cutting edge of the tool when cutting AISI 4340. This plateau is totally absent in all cutting of Inconel 718, even in short, two-minute tests. The crater intersects the cutting edge--only a thin wedge of carbide is left which either breaks off or deforms and wears very rapidly. Temperature measurements carried out by use of an infrared detector aimed on the corner of the tungsten carbide indicate at recommended speeds a sharp rise of the temperature at the beginning of the cutting operation, then a steady-state very slow increase as the cutting continues, and finally just before tool failure a very rapid increase in the temperature again. Scanning and replica electron microscopy through the crater and flank face shows that both under the crater and in the back of the cutting edge a fairly deep layer of ''disturbed metal'' exists in which the tungsten carbide grains are much smaller and have much more rounded edges than in the original material. 10 figures, 4 tables

Regge cuts in inclusive reactions

International Nuclear Information System (INIS)

Paige, F.E.; Trueman, T.L.

1975-01-01

The contribution of Regge cuts to single-particle inclusive processes is analyzed using the techniques of Gribov. The dependence of these contributions on the polarization state of the target is emphasized. A general formula is obtained and certain contributions to it are calculated. It is not possible, however, to reduce this to a simple, powerful formula expressing the total cut contribution in terms of other measurable quantities, as can be done for the cut contribution to the total cross section. The reasons for this are discussed in detail. The single-particle intermediate states, analogous to the absorption model for elastic scattering, are explicitly calculated as an illustration

International feedback experience on the cutting of reactor internal components

International Nuclear Information System (INIS)

Boucau, J.

2014-01-01

Westinghouse capitalizes more than 30 years of experience in the cutting of internal components of reactor and their packaging in view of their storage. Westinghouse has developed and validated different methods for cutting: plasma torch cutting, high pressure abrasive water jet cutting, electric discharge cutting and mechanical cutting. A long feedback experience has enabled Westinghouse to list the pros and cons of each cutting technology. The plasma torch cutting is fast but rises dosimetry concerns linked to the control of the cuttings and the clarity of water. Abrasive water jet cutting requires the installation of costly safety devices and of an equipment for filtering water but this technology allows accurate cuttings in hard-to-reach zones. Mechanical cutting is the most favourable technology in terms of wastes generation and of the clarity of water but the cutting speed is low. (A.C.)

Shearer drums - the cutting edge

Energy Technology Data Exchange (ETDEWEB)

O' Neill, M.; Wright, C.

2004-09-15

The paper discusses continuous miner and shearer cutters. It claims cutting drum require the same level of engineering know-how and technical expertise as do the machines driving them, and that the cutting drum, whether on a longwall shearer or continuous miner, comprises, the steel, pedestals, bit holders and the bits.

29 CFR 1910.254 - Arc welding and cutting.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Arc welding and cutting. 1910.254 Section 1910.254 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Welding, Cutting and Brazing § 1910.254 Arc welding and cutting. (a... following limits shall not be exceeded: (i) Alternating-current machines (A) Manual arc welding and cutting...

7 CFR 58.413 - Cutting and packaging rooms.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms shall be provided for the cleaning and preparation of the bulk cheese and for the cutting and wrapping...

Development of liner cutting method for stainless steel liner

International Nuclear Information System (INIS)

Takahata, Masato; Wignarajah, Sivakmaran; Kamata, Hirofumi

2005-01-01

The present work is an attempt to develop a laser cutting method for cutting and removing stainless steel liners from concrete walls and floors in cells and fuel storage pools of nuclear facilities. The effects of basic laser cutting parameters such as cutting speed, assist gas flow etc. were first studied applying a 1 kW Nd:YAG laser to mock up concrete specimens lined with 3 mm thick stainless steel sheets. These initial studies were followed by studies on the effect of unevenness of the liner surface and on methods of confining contamination during the cutting process. The results showed that laser cutting is superior to other conventional cutting methods from the point of view of safety from radioactivity and work efficiency when cutting contaminated stainless steel liners. In addition to the above results, this paper describes the design outline of a laser cutting system for cutting stainless liners at site and evaluates its merit and cost performance. (author)

7 CFR 58.726 - Cutting and grinding.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Cutting and grinding. 58.726 Section 58.726 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.726 Cutting and grinding. The trimmed and cleaned cheese should be cut into sections of...

Forms and Lability of Phosphorus in Algae and Aquatic Macrophytes Characterized by Solution 31P NMR Coupled with Enzymatic Hydrolysis

Science.gov (United States)

Feng, Weiying; Zhu, Yuanrong; Wu, Fengchang; He, Zhongqi; Zhang, Chen; Giesy, John P.

2016-11-01

Solution Phosphorus-31 nuclear magnetic resonance (31P NMR) spectroscopy coupled with enzymatic hydrolysis (EH) with commercially available phosphatases was used to characterize phosphorus (P) compounds in extracts of the dominant aquatic macrophytes and algae in a eutrophic lake. Total extractable organic P (Po) concentrations ranged from 504 to 1643 mg kg-1 and 2318 to 8395 mg kg-1 for aquatic macrophytes and algae, respectively. Using 31P NMR spectroscopy, 11 Po species were detected in the mono- and diester region. Additionally, orthophosphate, pyrophosphate and phosphonates were also detected. Using EH, phytate-like P was identified as the prevalent class of enzyme-labile Po, followed by labile monoester- and diester-P. Comparison of the NMR and EH data indicated that the distribution pattern of major P forms in the samples determined by the two methods was similar (r = 0.712, p < 0.05). Additional 31P NMR spectroscopic analysis of extracts following EH showed significant decreases in the monoester and pyrophosphate regions, with a corresponding increase in the orthophosphate signal, as compared to unhydrolyzed extracts. Based on these quantity and hydrolysis data, we proposed that recycling of Po in vegetative biomass residues is an important mechanism for long-term self-regulation of available P for algal blooming in eutrophic lakes.

A cutting force model for micromilling applications

DEFF Research Database (Denmark)

Bissacco, Giuliano; Hansen, Hans Nørgaard; De Chiffre, Leonardo

2006-01-01

In micro milling the maximum uncut chip thickness is often smaller than the cutting edge radius. This paper introduces a new cutting force model for ball nose micro milling that is capable of taking into account the effect of the edge radius.......In micro milling the maximum uncut chip thickness is often smaller than the cutting edge radius. This paper introduces a new cutting force model for ball nose micro milling that is capable of taking into account the effect of the edge radius....

Effects of Cutting Tool Parameters on Vibration

Directory of Open Access Journals (Sweden)

Ince Mehmet Alper

2016-01-01

Full Text Available This paper presents of the influence on vibration of Co28Cr6Mo medical alloy machined on a CNC lathe based on cutting parameters (rotational speed, feed rate, depth of cut and tool tip radius. The influences of cutting parameters have been presented in graphical form for understanding. To achieve the minimum vibration, the optimum values obtained for rpm, feed rate, depth of cut and tool tip radius were respectively, 318 rpm, 0.25 mm/rev, 0.9 mm and 0.8 mm. Maximum vibration has been revealed the values obtained for rpm, feed rate, depth of cut and tool tip radius were respectively, 636 rpm, 0.1 mm/rev, 0,5 mm and 0.8 mm.

Diamond wire cutting of heat exchangers

International Nuclear Information System (INIS)

Beckman, T.R.; Bjerler, J.

1991-01-01

With the change-out of equipment at nuclear power plants comes large quantities of low level contaminated metallic waste. Of particular concern are large heat exchangers, preheaters and steam generators. These bulky items consume huge volumes of burial space. The need for volume reduction and recycling of these metals has created new demands for 'how' to cut heat exchangers into useful sizes for decontamination, melting or compaction. This paper reviews the cutting solution provided by a diamond wire system, with particular regard for cutting of a Ringhals Preheater Bundle at Studsvik Nuclear in 1989. The background of diamond wire sawing is discussed and basic components of wire sawing are explained. Other examples of wire cutting decommissioned components are also given. (author)

Assembly procedure for column cutting platform

International Nuclear Information System (INIS)

Routh, R.D.

1995-01-01

This supporting document describes the assembly procedure for the Column Cutting Platform and Elevation Support. The Column Cutting Platform is a component of the 241-SY-101 Equipment Removal System. It is set up on the deck of the Strongback Trailer to provide work access to cut off the upper portion of the Mitigation Pump Assembly (MPA). The Elevation Support provides support for the front of the Storage Container with the Strongback at an inclined position. The upper portion of the MPA must be cut off to install the Containment Caps on the Storage Container. The storage Container must be maintained in an inclined position until the Containment Caps are installed to prevent any residual liquids from migrating forward in the Storage Container

49 CFR 236.52 - Relayed cut-section.

Science.gov (United States)

2010-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Rules and Instructions: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...

LASER CUTTING MACHINES FOR 3-D THIN SHEET PARTS

Directory of Open Access Journals (Sweden)

Miroslav RADOVANOVIC

2012-11-01

Full Text Available Laser cutting machines are used for precise contour cutting thin sheet. In industrial application nowadays various types and construction of laser cutting machines can be met. For contour cutting 3-D thin sheet parts laser cutting machines with rotation movements and laser robots are used. Laser generates the light beam, that presents a tool in working process. Application of laser cutting machines made possible good quality of products, flexibility of production and enlargement of economy

Electric arc, water jet cutting of metals

International Nuclear Information System (INIS)

Bruening, D.

1991-01-01

For thermal dismantling and cutting of metallic components, as electric arc, water jet cutting method was developed that can be used for underwater cutting work up to a depth of 20 m. Short-circuiting of a continuously fed electrode wire in contact with the metal generates an electric arc which induces partial melting of the metal, and the water jet surrounding the wire rinses away the molten material, thus making a continuous kerf in the material. The method was also tested and modified to allow larger area, surface cutting and removal of metallic surface coatings. This is achieved by melting parts of the surface with the electric arc and subsequent rinsing by the water jet. The cutting and melting depth for surface removal can be accurately controlled by the operating parameters chosen. (orig./DG) [de

Modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for straight profile

Science.gov (United States)

Sharma, Amit; Yadava, Vinod

2012-02-01

Thin sheets of aluminium alloys are widely used in aerospace and automotive industries for specific applications. Nd:YAG laser beam cutting is one of the most promising sheetmetal cutting process for cutting sheets for any profile. Al-alloy sheets are difficult to cut by laser beam because of its highly reflective nature. This paper presents modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for straight profile. In the present study, four input process parameters such as oxygen pressure, pulse width, pulse frequency, and cutting speed and two output parameters such as average kerf taper ( Ta) and average surface roughness ( Ra) are considered. The hybrid approach comprising of Taguchi methodology (TM) and response surface methodology (RSM) is used for modelling whereas multi-objective optimization is performed using hybrid approach of TM and grey relational analysis (GRA) coupled with entropy measurement methodology. The entropy measurement methodology is employed for the calculation of weight corresponding to each quality characteristic. The results indicate that the hybrid approaches applied for modelling and optimization of the LBC process are reasonable.

Sequence specificity of alkali-labile DNA damage photosensitized by suprofen.

Science.gov (United States)

Starrs, S M; Davies, R J

2000-09-01

On irradiation at UVB wavelengths, in aerated neutral aqueous solution, the anti-inflammatory drug suprofen (SP) photosensitizes the production of alkali-labile cleavage sites in DNA much more efficiently than direct strand breaks. It is active at submillimolar concentrations despite having no significant binding affinity for DNA. Gel sequencing studies utilizing 32P-end-labeled oligonucleotides have revealed that piperidine-sensitive lesions are formed predominantly at the positions of guanine (G) bases, with the extent of modification being UV dose- and SP concentration-dependent. Quite distinct patterns of G-specific damage are observed in single-stranded and duplex DNA molecules. The uniform attack at all G residues in single-stranded DNA, which is enhanced in D2O, is compatible with a Type-II mechanism. SP is a known generator of singlet oxygen whose participation in the reaction is supported by the effects of quenchers and scavengers. In duplex DNA, piperidine-induced cleavage occurs with high selectivity at the 5'-G of GG and (less prominently) GA doublets. This behavior is characteristic of a Type-I process involving electron transfer from DNA to photoexcited SP molecules. The ability of SP to sensitize the formation of Type-I and Type-II photo-oxidation products from 2'-deoxyguanosine attests to the feasibility of competing mechanisms in DNA.

Neodymium:YAG laser cutting of intraocular lens haptics.

Science.gov (United States)

Gorn, R A; Steinert, R F

1985-11-01

Neodymium:YAG laser cutting of polymethylmethacrylate and polypropylene anterior chamber and posterior chamber intraocular lens haptics was studied in terms of ease of transection and physical structure of the cut areas as seen by scanning electron microscopy. A marked difference was discovered, with the polymethylmethacrylate cutting easily along transverse planes, whereas the polypropylene resisted cutting along longitudinal fibers. Clinical guidelines are presented.

Automated Cell-Cutting for Cell Cloning

Science.gov (United States)

Ichikawa, Akihiko; Tanikawa, Tamio; Matsukawa, Kazutsugu; Takahashi, Seiya; Ohba, Kohtaro

We develop an automated cell-cutting technique for cell cloning. Animal cells softened by the cytochalasin treatment are injected into a microfluidic chip. The microfluidic chip contains two orthogonal channels: one microchannel is wide, used to transport cells, and generates the cutting flow; the other is thin and used for aspiration, fixing, and stretching of the cell. The injected cell is aspirated and stretched in the thin microchannel. Simultaneously, the volumes of the cell before and after aspiration are calculated; the volumes are used to calculate the fluid flow required to aspirate half the volume of the cell into the thin microchannel. Finally, we apply a high-speed flow in the orthogonal microchannel to bisect the cell. This paper reports the cutting process, the cutting system, and the results of the experiment.

Benefits of explosive cutting for nuclear-facility applications

International Nuclear Information System (INIS)

Hazelton, R.F.; Lundgren, R.A.; Allen, R.P.

1981-06-01

The study discussed in this report was a cost/benefit analysis to determine: (1) whether explosive cutting is cost effective in comparison with alternative metal sectioning methods and (2) whether explosive cutting would reduce radiation exposure or provide other benefits. Two separate approaches were pursued. The first was to qualitatively assess cutting methods and factors involved in typical sectioning cases and then compare the results for the cutting methods. The second was to prepare estimates of work schedules and potential radiation exposures for candidate sectioning methods for two hypothetical, but typical, sectioning tasks. The analysis shows that explosive cutting would be cost effective and would also reduce radiation exposure when used for typical nuclear facility sectioning tasks. These results indicate that explosive cutting should be one of the principal cutting methods considered whenever steel or similar metal structures or equipment in a nuclear facility are to be sectioned for repair or decommissioning. 13 figures, 7 tables

Budget Cuts: Financial Aid Offices Face Budget Cuts and Increasing Workload. Quick Scan Survey Results

Science.gov (United States)

National Association of Student Financial Aid Administrators (NJ1), 2010

2010-01-01

The majority of college financial aid offices have seen cuts to their operating budgets this year compared to the 2007-08 academic year when the recession began, according to the National Association of Student Financial Aid Administrator's latest QuickScan Survey. Sixty-two percent of financial aid offices reported operating budget cuts this year…

Cut elimination in multifocused linear logic

DEFF Research Database (Denmark)

Guenot, Nicolas; Brock-Nannestad, Taus

2015-01-01

We study cut elimination for a multifocused variant of full linear logic in the sequent calculus. The multifocused normal form of proofs yields problems that do not appear in a standard focused system, related to the constraints in grouping rule instances in focusing phases. We show that cut...... elimination can be performed in a sensible way even though the proof requires some specific lemmas to deal with multifocusing phases, and discuss the difficulties arising with cut elimination when considering normal forms of proofs in linear logic....

Application of response surface methodology for determining cutting ...

Indian Academy of Sciences (India)

The results indicate that the depth of cut is the dominant factor affecting cutting ... between forces and cutting regime could be represented by power function type ..... CNEPRU Research Project, CODE : 0301520090008 (University of Guelma).

Thermophysical problems of laser cutting of metals

Directory of Open Access Journals (Sweden)

Orishich Anatoliy

2017-01-01

Full Text Available Variety and complex interaction of physical processes during laser cutting is a critical characteristic of the laser cutting of metals. Small spatial and temporal scales complicate significantly the experimental investigations of the multi-phase fluid flow in the conditions of laser cutting of metals. In these conditions, the surface formed during the cutting is an indicator determining the melt flow character. The quantitative parameter reflecting the peculiarities of the multi-phase fluid flow, is normally the roughness of the forming surface, and the minimal roughness is the criterion of the qualitative flow [1 – 2]. The purpose of this work is to perform the experimental comparative investigation of the thermophysical pattern of the multi-phase melt flow in the conditions of the laser cutting of metals with the laser wavelength of 10.6 μm and 1.07 μm.

Fractal characteristic study of shearer cutter cutting resistance curves

Energy Technology Data Exchange (ETDEWEB)

Liu, C. [Heilongjiang Scientific and Technical Institute, Haerbin (China). Dept of Mechanical Engineering

2004-02-01

The cutting resistance curve is the most useful tool for reflecting the overall cutting performance of a cutting machine. The cutting resistance curve is influenced by many factors such as the pick structure and arrangement, the cutter operation parameters, coal quality and geologic conditions. This paper discusses the use of fractal geometry to study the properties of the cutting resistance curve, and the use of fractal dimensions to evaluate cutting performance. On the basis of fractal theory, the general form and calculation method of fractal characteristics are given. 4 refs., 3 figs., 1 tab.

Effect of cutting temperature on hardness of SiC and diamond in the nano-cutting process of monocrystalline silicon

Science.gov (United States)

Wang, Jiachun; Li, Yuntao; Liu, Xiaoxuan; Lv, Maoqiang

2016-10-01

In the process of cutting silicon by natural diamond tools, groove wear happens on the flank face of cutting tool frequently.Scholars believe that one of the wear reasons is mechanical scratching effect by hard particles like SiC. To reveal the mechanical scratching mechanism, it is essential to study changes in the mechanical properties of hard particles and diamond, especially the effect of cutting temperature on hardness of diamond and hard particles. Molecular dynamics (MD) model that contact-zone temperature between tool and workpiece was calculated by dividing zone while nano-cutting monocrystalline silicon was established, cutting temperature values in different regions were computed as the simulation was carried out.On this basis, the models of molecular dynamics simulation of SiC and diamond were established separately with setting the initial temperature to room temperature. The laws of length change of C-C bond and Si-C bond varing with increase of simulation temperature were studied. And drawing on predecessors' research on theoretical calculation of hardness of covalent crystals and the relationship between crystal valence electron density and bond length, the curves that the hardness of diamond and SiC varing with bond length were obtained. The effect of temperature on the hardness was calculated. Results show that, local cutting temperature can reach 1300K.The rise in cutting temperature leaded to a decrease in the diamond local atomic clusters hardness,SiC local atomic clusters hardness increased. As the cutting temperature was more than 1100K,diamond began to soften, the local clusters hardness was less than that of SiC.

Recent results in mirror based high power laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Nielsen, Jakob Skov; Elvang, Mads

2004-01-01

In this paper, recent results in high power laser cutting, obtained in reseach and development projects are presented. Two types of mirror based focussing systems for laser cutting have been developed and applied in laser cutting studies on CO2-lasers up to 12 kW. In shipyard environment cutting...... speed increase relative to state-of-the-art cutting of over 100 % has been achieved....

Magnetofluidic testing of rock cutting knives

International Nuclear Information System (INIS)

Buioca, C.D.; Iusan, Vasile; Pirlea, Remus

2002-01-01

The nondestructive testing of cutting knives consists in the determination of nonuniformity of a magnetic fluid layer applied on the horizontally placed surface of the magnetized cutting plate of the knife. A low constant magnetic field was applied perpendicular to the knife surface and a uniform magnetic fluid layer was applied. The defects as nonuniform brass layer, fissures or small cavities between the cutting plate and knife core determine the apparition of magnetic field gradients and therefore magnetic forces acting on the magnetic fluid which migrates to the zones with higher magnetic field intensity. After several minutes, a nonuniform layer of magnetic fluid was directly observed. Quantitative results, concerning the position and dimensions of the defect, were obtained by computer aided processing of the magnetic fluid layer image. Experimental data for several cutting knives are presented in the paper

Inhibition of growth and biofilm formation of clinical bacterial isolates by NiO nanoparticles synthesized from Eucalyptus globulus plants.

Science.gov (United States)

Saleem, Samia; Ahmed, Bilal; Khan, Mohammad Saghir; Al-Shaeri, Majed; Musarrat, Javed

2017-10-01

Nanotechnology based therapeutics has emerged as a promising approach for augmenting the activity of existing antimicrobials due to the unique physical and chemical properties of nanoparticles (NPs). Nickel oxide nanoparticles (NiO-NPs) have been suggested as prospective antibacterial and antitumor agent. In this study, NiO-NPs have been synthesized by a green approach using Eucalyptus globulus leaf extract and assessed for their bactericidal activity. The morphology and purity of synthesized NiO-NPs determined through various spectroscopic techniques like UV-Visible, FT-IR, XRD, EDX and electron microscopy differed considerably. The synthesized NiO-NPs were pleomorphic varying in size between 10 and 20 nm. The XRD analysis revealed the average size of NiO-NPs as 19 nm. The UV-Vis spectroscopic data showed a strong SPR of NiO-NPs with a characteristic spectral peak at 396 nm. The FTIR data revealed various functional moieties like C=C, C-N, C-H and O-H which elucidate the role of leaf biomolecules in capping and dispersal of NiO-NPs. The bioactivity assay revealed the antibacterial and anti-biofilm activity of NiO-NPs against ESβL (+) E. coli, P. aeruginosa, methicillin sensitive and resistant S. aureus. Growth inhibition assay demonstrated time and NiO-NPs concentration dependent decrease in the viability of treated cells. NiO-NPs induced biofilm inhibition was revealed by a sharp increase in characteristic red fluorescence of PI, while SEM images of NiO-NPs treated cells were irregular shrink and distorted with obvious depressions/indentations. The results suggested significant antibacterial and antibiofilm activity of NiO-NPs which may play an important role in the management of infectious diseases affecting human health. Copyright © 2017 Elsevier Ltd. All rights reserved.

Laser cutting - from 200 Watt to 12 Kilowatt

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Nielsen, Jakob Skov

2004-01-01

Laser cutting is the most widespread industrial application of high power lasers. The development of this process was initiated around 1970, when scientists at TWI first demonstrated laser cutting with coaxial gas assistance. 10 years later, the polarisation problem was solved and the technology ...... got its breakthrough. Since then some 30,000 laser cutting systems have been installed worldwide, making the laser an important cutting tool in modern industry....

Investigation of tool engagement and cutting performance in machining a pocket

Science.gov (United States)

Adesta, E. Y. T.; Hamidon, R.; Riza, M.; Alrashidi, R. F. F. A.; Alazemi, A. F. F. S.

2018-01-01

This study investigates the variation of tool engagement for different profile of cutting. In addition, behavior of cutting force and cutting temperature for different tool engagements for machining a pocket also been explored. Initially, simple tool engagement models were developed for peripheral and slot cutting for different types of corner. Based on these models, the tool engagements for contour and zig zag tool path strategies for a rectangular shape pocket with dimension 80 mm x 60 mm were analyzed. Experiments were conducted to investigate the effect of tool engagements on cutting force and cutting temperature for the machining of a pocket of AISI H13 material. The cutting parameters used were 150m/min cutting speed, 0.05mm/tooth feed, and 0.1mm depth of cut. Based on the results obtained, the changes of cutting force and cutting temperature performance there exist a relationship between cutting force, cutting temperature and tool engagement. A higher cutting force and cutting temperature is obtained when the cutting tool goes through up milling and when the cutting tool makes a full engagement with the workpiece.

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718

Directory of Open Access Journals (Sweden)

Bing Wang

2018-03-01

Full Text Available The paper aims to investigate the influences of material constitutive and fracture parameters in addition to cutting speed on chip formation during high-speed cutting of Inconel 718. Finite element analyses for chip formation are conducted with Johnson–Cook constitutive and fracture models. Meanwhile, experiments of high-speed orthogonal cutting are performed to verify the simulation results with cutting speeds ranging from 50 m/min to 7000 m/min. The research indicates that the chip morphology transforms from serrated to fragmented at the cutting speed of 7000 m/min due to embrittlement of the workpiece material under ultra-high cutting speeds. The parameter of shear localization sensitivity is put forward to describe the influences of material mechanical properties on serrated chip formation. The results demonstrate that the effects of initial yield stress and thermal softening coefficient on chip shear localization are much more remarkable than the other constitutive parameters. For the material fracture parameters, the effects of initial fracture strain and exponential factor of stress state on chip shear localization are more much prominent. This paper provides guidance for controlling chip formation through the adjustment of material mechanical properties and the selection of appropriate cutting parameters.

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718.

Science.gov (United States)

Wang, Bing; Liu, Zhanqiang; Hou, Xin; Zhao, Jinfu

2018-03-21

The paper aims to investigate the influences of material constitutive and fracture parameters in addition to cutting speed on chip formation during high-speed cutting of Inconel 718. Finite element analyses for chip formation are conducted with Johnson-Cook constitutive and fracture models. Meanwhile, experiments of high-speed orthogonal cutting are performed to verify the simulation results with cutting speeds ranging from 50 m/min to 7000 m/min. The research indicates that the chip morphology transforms from serrated to fragmented at the cutting speed of 7000 m/min due to embrittlement of the workpiece material under ultra-high cutting speeds. The parameter of shear localization sensitivity is put forward to describe the influences of material mechanical properties on serrated chip formation. The results demonstrate that the effects of initial yield stress and thermal softening coefficient on chip shear localization are much more remarkable than the other constitutive parameters. For the material fracture parameters, the effects of initial fracture strain and exponential factor of stress state on chip shear localization are more much prominent. This paper provides guidance for controlling chip formation through the adjustment of material mechanical properties and the selection of appropriate cutting parameters.

Hot regions of labile and stable soil organic carbon in Germany - Spatial variability and driving factors

Science.gov (United States)

Vos, Cora; Jaconi, Angélica; Jacobs, Anna; Don, Axel

2018-06-01

Atmospheric carbon dioxide levels can be mitigated by sequestering carbon in the soil. Sequestration can be facilitated by agricultural management, but its influence is not the same on all soil carbon pools, as labile pools with a high turnover may be accumulated much faster but are also more vulnerable to losses. The aims of this study were to (1) assess how soil organic carbon (SOC) is distributed among SOC fractions on a national scale in Germany, (2) identify factors influencing this distribution and (3) identify regions with high vulnerability to SOC losses. The SOC content and proportion of two different SOC fractions were estimated for more than 2500 mineral topsoils (soil texture, bulk soil C / N ratio, total SOC content and pH. For some regions, the drivers were linked to the land-use history of the sites. Arable topsoils in central and southern Germany were found to contain the highest proportions and contents of stable SOC fractions, and therefore have the lowest vulnerability to SOC losses. North-western Germany contains an area of sandy soils with unusually high SOC contents and high proportions of light SOC fractions, which are commonly regarded as representing a labile carbon pool. This is true for the former peat soils in this area, which have already lost and are at high risk of losing high proportions of their SOC stocks. Those black sands can, however, also contain high amounts of stable SOC due to former heathland vegetation and need to be treated and discussed separately from non-black sand agricultural soils. Overall, it was estimated that, in large areas all over Germany, over 30 % of SOC is stored in easily mineralisable forms. Thus, SOC-conserving management of arable soils in these regions is of great importance.

Underwater transporting method and device for incore structure cutting piece

International Nuclear Information System (INIS)

Kurosawa, Koichi; Chiba, Noboru; Chiba, Isao; Takada, Hiroshi; Furukawa, Hideyasu; Chiba, Noboru.

1996-01-01

Cutting pieces are handled by using a pick-up device connected with a wire ropes, a take-up drum, chains and a winch as cutting piece handling means, and moved freely on the water surface by a propulsion machine of a transporting means of the device to transfer them under water to a predetermined position. The pick-up device is lifted by taking-up the rope by the rotation of the take-up drum using chain-driving by way of the winch and the chains. The cut pieces are stored in a cask by lowering them in the cask and releasing the handling. In addition, if the weight of the cut pieces is recognized before cutting, and the load of the weight of the cut pieces is applied to the device previously, the balance of the device and the cut pieces can be kept, and cut pieces can be transported under water always stably. Further, if the cut pieces are supported upon cutting operation, the cut pieces are made stable, and cutting operation with good efficiency can be attained. (N.H.)

Counterbalance of cutting force for advanced milling operations

Science.gov (United States)

Tsai, Nan-Chyuan; Shih, Li-Wen; Lee, Rong-Mao

2010-05-01

The goal of this work is to concurrently counterbalance the dynamic cutting force and regulate the spindle position deviation under various milling conditions by integrating active magnetic bearing (AMB) technique, fuzzy logic algorithm and an adaptive self-tuning feedback loop. Since the dynamics of milling system is highly determined by a few operation conditions, such as speed of spindle, cut depth and feedrate, therefore the dynamic model for cutting process is more appropriate to be constructed by experiments, instead of using theoretical approach. The experimental data, either for idle or cutting, are utilized to establish the database of milling dynamics so that the system parameters can be on-line estimated by employing the proposed fuzzy logic algorithm as the cutting mission is engaged. Based on the estimated milling system model and preset operation conditions, i.e., spindle speed, cut depth and feedrate, the current cutting force can be numerically estimated. Once the current cutting force can be real-time estimated, the corresponding compensation force can be exerted by the equipped AMB to counterbalance the cutting force, in addition to the spindle position regulation by feedback of spindle position. On the other hand, for the magnetic force is nonlinear with respect to the applied electric current and air gap, the characteristics of the employed AMB is investigated also by experiments and a nonlinear mathematic model, in terms of air gap between spindle and electromagnetic pole and coil current, is developed. At the end, the experimental simulations on realistic milling are presented to verify the efficacy of the fuzzy controller for spindle position regulation and the capability of the dynamic cutting force counterbalance.

Metal Cutting for Large Component Removal

International Nuclear Information System (INIS)

Hulick, Robert M.

2008-01-01

Decommissioning of commercial nuclear power plants presents technological challenges. One major challenge is the removal of large components mainly consisting of the reactor vessel, steam generators and pressurizer. In order to remove and package these large components nozzles must be cut from the reactor vessel to precise tolerances. In some cases steam generators must be segmented for size and weight reduction. One innovative technology that has been used successfully at several commercial nuclear plant decommissioning is diamond wire sawing. Diamond wire sawing is performed by rotating a cable with diamond segments attached using a flywheel approximately 24 inches in diameter driven remotely by a hydraulic pump. Tension is provided using a gear rack drive which also takes up the slack in the wire. The wire is guided through the use of pulleys keeps the wire in a precise location. The diamond wire consists of 1/4 inch aircraft cable with diamond beads strung over the cable separated by springs and brass crimps. Standard wire contains 40 diamond beads per meter and can be made to any length. Cooling the wire and controlling the spread of contamination presents significant challenges. Under normal circumstances the wire is cooled and the cutting kerf cleaned by using water. In some cases of reactor nozzle cuts the use of water is prohibited because it cannot be controlled. This challenge was solved by using liquid Carbon Dioxide as the cooling agent. The liquid CO 2 is passed through a special nozzle which atomizes the liquid into snowflakes which is introduced under pressure to the wire. The snowflakes attach to the wire keeping it cool and to the metal shavings. As the CO 2 and metal shavings are released from the wire due to its fast rotation, the snowflakes evaporate leaving only the fine metal shavings as waste. Secondary waste produced is simply the small volume of fine metal shavings removed from the cut surface. Diamond wire sawing using CO 2 cooling has

Cutting of nonmetallic materials using Nd:YAG laser beam

Institute of Scientific and Technical Information of China (English)

Bashir Ahmed Tahir; Rashid Ahmed; M. G. B. Ashiq; Afaq Ahmed; M. A. Saeed

2012-01-01

This study deals with Nd:YAG laser cutting nonmetallic materials,which is one of the most important and popular industrial applications of laser.The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed.For approximate cutting depth,a theoretical study is conducted in terms of material property and cutting speed.Results show a nonlinear relation between the cutting depth and input energy.There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s.An extra energy is utilized in the deep cutting.It is inferred that as the laser power increases,cutting depth increases.The experimental outcomes are in good agreement with theoretical results.This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting,scribing,trimming,engraving,and marking nonmetallic materials.

Effect of cutting fluids and cutting conditions on surface integrity and tool wear in turning of Inconel 713C

Science.gov (United States)

Hikiji, R.

2018-01-01

The trend toward downsizing of engines helps to increase the number of turbochargers around Europe. As for the turbocharger, the temperature of the exhaust gas is so high that the parts made of nickel base super alloy Inconel 713C are used as high temperature strength metals. External turning of Inconel 713C which is used as the actual automotive parts was carried out. The effect of the cutting fluids and cutting conditions on the surface integrity and tool wear was investigated, considering global environment and cost performance. As a result, in the range of the cutting conditions used this time, when the depth of cut was small, the good surface integrity and tool life were obtained. However, in the case of the large corner radius, it was found that the more the cutting length increased, the more the tool wear increased. When the cutting length is so large, the surface integrity and tool life got worse. As for the cutting fluids, it was found that the synthetic type showed better performance in the surface integrity and tool life than the conventional emulsion. However, it was clear that the large corner radius made the surface roughness and tool life good, but it affected the size error etc. in machining the workpiece held in a cantilever style.

MULTI-OBJECTIVE OPTIMISATION OF LASER CUTTING USING CUCKOO SEARCH ALGORITHM

Directory of Open Access Journals (Sweden)

M. MADIĆ

2015-03-01

Full Text Available Determining of optimal laser cutting conditions for improving cut quality characteristics is of great importance in process planning. This paper presents multi-objective optimisation of the CO2 laser cutting process considering three cut quality characteristics such as surface roughness, heat affected zone (HAZ and kerf width. It combines an experimental design by using Taguchi’s method, modelling the relationships between the laser cutting factors (laser power, cutting speed, assist gas pressure and focus position and cut quality characteristics by artificial neural networks (ANNs, formulation of the multiobjective optimisation problem using weighting sum method, and solving it by the novel meta-heuristic cuckoo search algorithm (CSA. The objective is to obtain optimal cutting conditions dependent on the importance order of the cut quality characteristics for each of four different case studies presented in this paper. The case studies considered in this study are: minimisation of cut quality characteristics with equal priority, minimisation of cut quality characteristics with priority given to surface roughness, minimisation of cut quality characteristics with priority given to HAZ, and minimisation of cut quality characteristics with priority given to kerf width. The results indicate that the applied CSA for solving the multi-objective optimisation problem is effective, and that the proposed approach can be used for selecting the optimal laser cutting factors for specific production requirements.

ANALYSIS OF CUTTING FORCES ON CNC LATHES EXPERIMENTAL APPROACH

Directory of Open Access Journals (Sweden)

Erdem Koç

1996-01-01

Full Text Available Objective of this study is to make use easy programming of CNC lathes and to achieve the optimization of part program prepared considering the limiting parameters of the machine. In the present study, a BOXFORD 250 B CNC lathe has been used for experiment and optimization process. The measurement of cutting forces exerted on the cutting tool of CNC lathe has been performed. The cutting forces occurring during the turning operation have been determined for different depth of" cut, feed rate and cutting speed as well as different cutting tools and related data base has been obtained.

Ceramic cutting tools materials, development and performance

CERN Document Server

Whitney, E Dow

1994-01-01

Interest in ceramics as a high speed cutting tool material is based primarily on favorable material properties. As a class of materials, ceramics possess high melting points, excellent hardness and good wear resistance. Unlike most metals, hardness levels in ceramics generally remain high at elevated temperatures which means that cutting tip integrity is relatively unaffected at high cutting speeds. Ceramics are also chemically inert against most workmetals.

Precision Machining When Cutting with Leading Plastic Deformation

Directory of Open Access Journals (Sweden)

N. A. Yaroslavtseva

2017-01-01

Full Text Available Keeping up the product competitiveness continually requires solving the problems of reducing time for product creation and material costs for its production and ensuring the maximum conformity of the product quality with the individual requirements of a particular consumer. It is especially difficult to implement these tasks in product manufacturing from the hard-to-machine steels and alloys with extremely low production rate in machining (often 10-20 times lower than when cutting the ordinary structural steels.Currently, one of the promising ways to improve the cutting process of hard-to-machine materials and quality of parts made from these materials is development and application of combined processing methods, which use additional energy sources to act on the machined material in the cutting zone. A BMSTU-developed cutting method with leading plastic deformation (LPD, which acts to raise the production rate, gain the cutting tool-life, reduce the surface roughness, improve the accuracy of processing and the performance characteristics of products, ensure the reliable flow chip control, and improve the labor conditions, belongs to such sort of methods.One of the most important indicators of processing quality that has a great impact on the operation and cost characteristics of the product and on the machining rate as well is the accuracy of processing. In cutting, the processing errors largely arise from the elastic deformations of a technological system when the cutting force, and, in particular, the radial component of the cutting force, acts on it.The deforming devices, used in cutting with LPD, being located as a rule, on the diametrically opposite side with respect to the cutting zone, act on the technological system as vibration dampers. In addition, as studies have shown, the choice of a rational direction for applying LPD load helps to compensate partially or completely the cutting force radial component effect on the technological

Persistent long-term facilitation at an identified synapse becomes labile with activation of short-term heterosynaptic plasticity.

Science.gov (United States)

Hu, Jiang-Yuan; Schacher, Samuel

2014-04-02

Short-term and long-term synaptic plasticity are cellular correlates of learning and memory of different durations. Little is known, however, how these two forms of plasticity interact at the same synaptic connection. We examined the reciprocal impact of short-term heterosynaptic or homosynaptic plasticity at sensorimotor synapses of Aplysia in cell culture when expressing persistent long-term facilitation (P-LTF) evoked by serotonin [5-hydroxytryptamine (5-HT)]. Short-term heterosynaptic plasticity induced by 5-HT (facilitation) or the neuropeptide FMRFa (depression) and short-term homosynaptic plasticity induced by tetanus [post-tetanic potentiation (PTP)] or low-frequency stimulation [homosynaptic depression (HSD)] of the sensory neuron were expressed in both control synapses and synapses expressing P-LTF in the absence or presence of protein synthesis inhibitors. All forms of short-term plasticity failed to significantly affect ongoing P-LTF in the absence of protein synthesis inhibitors. However, P-LTF reversed to control levels when either 5-HT or FMRFa was applied in the presence of rapamycin. In contrast, P-LTF was unaffected when either PTP or HSD was evoked in the presence of either rapamycin or anisomycin. These results indicate that synapses expressing persistent plasticity acquire a "new" baseline and functionally express short-term changes as naive synapses, but the new baseline becomes labile following selective activations-heterosynaptic stimuli that evoke opposite forms of plasticity-such that when presented in the presence of protein synthesis inhibitors produce a rapid reversal of the persistent plasticity. Activity-selective induction of a labile state at synapses expressing persistent plasticity may facilitate the development of therapies for reversing inappropriate memories.

Long-term effects of clear-cutting and selective cutting on soil methane fluxes in a temperate spruce forest in southern Germany

International Nuclear Information System (INIS)

Wu Xing; Brueggemann, Nicolas; Gasche, Rainer; Papen, Hans; Willibald, Georg; Butterbach-Bahl, Klaus

2011-01-01

Based on multi-year measurements of CH 4 exchange in sub-daily resolution we show that clear-cutting of a forest in Southern Germany increased soil temperature and moisture and decreased CH 4 uptake. CH 4 uptake in the first year after clear-cutting (-4.5 ± 0.2 μg C m -2 h -1 ) was three times lower than during the pre-harvest period (-14.2 ± 1.3 μg C m -2 h -1 ). In contrast, selective cutting did not significantly reduce CH 4 uptake. Annual mean uptake rates were -1.18 kg C ha -1 yr -1 (spruce control), -1.16 kg C ha -1 yr -1 (selective cut site) and -0.44 kg C ha -1 yr -1 (clear-cut site), respectively. Substantial seasonal and inter-annual variations in CH 4 fluxes were observed as a result of significant variability of weather conditions, demonstrating the need for long-term measurements. Our findings imply that a stepwise selective cutting instead of clear-cutting may contribute to mitigating global warming by maintaining a high CH 4 uptake capacity of the soil. - Highlights: → Long-term, sub-daily measurements of CH 4 exchange at differently managed forest sites. → Inter-annual variability in CH 4 uptake is affected by annual precipitation. → Clear-cutting reduces the CH 4 sink strength of forest soils, whereas thinning has no significant effect. → Sink strength changes due to clear cutting are long-term and were still present approx. nine years following forest harvest. - Forest management affects the soil CH 4 sink strength, with clear-cutting reducing uptake rates for at least eight years.

Non-Poissonian photon statistics from macroscopic photon cutting materials.

Science.gov (United States)

de Jong, Mathijs; Meijerink, Andries; Rabouw, Freddy T

2017-05-24

In optical materials energy is usually extracted only from the lowest excited state, resulting in fundamental energy-efficiency limits such as the Shockley-Queisser limit for single-junction solar cells. Photon-cutting materials provide a way around such limits by absorbing high-energy photons and 'cutting' them into multiple low-energy excitations that can subsequently be extracted. The occurrence of photon cutting or quantum cutting has been demonstrated in a variety of materials, including semiconductor quantum dots, lanthanides and organic dyes. Here we show that photon cutting results in bunched photon emission on the timescale of the excited-state lifetime, even when observing a macroscopic number of optical centres. Our theoretical derivation matches well with experimental data on NaLaF 4 :Pr 3+ , a material that can cut deep-ultraviolet photons into two visible photons. This signature of photon cutting can be used to identify and characterize new photon-cutting materials unambiguously.

Cutting of nonmetallic materials using Nd:YAG laser beam

International Nuclear Information System (INIS)

Tahir, Bashir Ahmed; Ashiq, M.G. B.; Saeed, M.A.; Ahmed, Rashid; Ahmed, Afaq

2012-01-01

This study deals with Nd:YAG laser cutting nonmetallic materials, which is one of the most important and popular industrial applications of laser. The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed. For approximate cutting depth, a theoretical study is conducted in terms of material property and cutting speed. Results show a nonlinear relation between the cutting depth and input energy. There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s. An extra energy is utilized in the deep cutting. It is inferred that as the laser power increases, cutting depth increases. The experimental outcomes are in good agreement with theoretical results. This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting, scribing, trimming, engraving, and marking nonmetallic materials. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal and non thermal cutting methods

International Nuclear Information System (INIS)

Bienia, H.

2008-01-01

Remote disassembly of radiologically burdened large components is among the most sophisticated and complex activities in the dismantling of nuclear installations. The required space for the technical equipment during the dismantling operations, especially for the removal of larger components is often an additional problem. Conventional cutting technologies like sawing with a disk saw or band saw require large and heavy frameworks as well as guiding systems with high rigidity. These solutions are expensive and sometimes not applicable. The essential question of all cutting and dismantling tasks is the physiological constitution of the component which will be dismantled. That means size, material and structure of the component. All these points are primarily technological questions. The last question is about the estimated costs of the used dismantling technology. Therefore following questions must be answered. How much are the investments for the cutting equipment itself and how much are the investments for the supporting equipment (e.g. necessary handling equipment)? Can I use this cutting equipment only for one special task or is it applicable for many tasks and therefore saves money because other cutting or dismantling technologies are dispensable? How long is the cutting time and what is the to control this technique required personnel? Four different cutting and dismantling technologies will be introduced and described. These four technologies differ in their principle of operation but all of them are used by cutting and dismantling tasks in nuclear power plants. (author)

Argon direct analysis in real time mass spectrometry in conjunction with makeup solvents: a method for analysis of labile compounds.

Science.gov (United States)

Yang, Hongmei; Wan, Debin; Song, Fengrui; Liu, Zhiqiang; Liu, Shuying

2013-02-05

Helium direct analysis in real time (He-DART) mass spectrometry (MS) analysis of labile compounds usually tends to be challenging because of the occurrence of prominent fragmentation, which obscures the assigning of an ion to an independent species or merely a fragment in a mixture. In the present work, argon DART (Ar-DART) MS in conjunction with makeup solvents has been demonstrated to analyze a variety of labile compounds including nucleosides, alkaloids, glucose, and other small molecules. The results presented here confirm that Ar-DART can generate significantly less energetic ions than conventional He-DART and is able to produce the intact molecular ions with little or no fragmentation in both positive and negative ion modes. Adding a makeup solvent (absolute ethyl alcohol, methanol, fluorobenzene, or acetone) to the argon gas stream at the exit of the DART ion source can result in 1-2 orders of magnitude increase in detection signals. The sensitivity attainable by Ar-DART was found to be comparable to that by He-DART. The investigation of influence of solvents improves our understanding of the fundamental desorption and ionization processes in DART. The practical application of this rapid and high throughput method is demonstrated by the successful analysis of a natural product (Crude Kusnezoff Monkshood) extract, demonstrating the great potential in mixture research.

Effect of age on calorific value and some mechanical properties of three Eucalyptus species grown in Ethiopia

Energy Technology Data Exchange (ETDEWEB)

Mulugeta Lemenih; Tsegaye Bekele [Wondo Genet College of Forestry, Shashemene (Ethiopia)

2004-09-01

The effect of age on calorific value, specific gravity, modulus of rupture (MOR) and modulus of elasticity (MOE) of three plantation grown Eucalyptus species in the south-central highlands of Ethiopia was investigated. The species investigated were Eucalyptus globulus Labill., E. saligna Sm. and E grandis W. Hill ex Maid. The investigation was made on sample trees taken from age sequences of stands of the three species. Calorific values were determined on sample discs taken at 4, 8, 12 and 16 m up the stems of the sample trees. Calorific values were also determined for heartwood and sapwood of each disc separately. Specific gravity, MOR and MOE were investigated on a 1 -m long sample log taken from the butt end of each sample tree. The results showed that there was no significant difference in calorific values between the three species when considering a similar age category. Similarly, there was no significant difference in calorific values between disc positions and wood types (heartwood versus sapwood) within species. However, calorific values tend to increase along the tree stem towards the treetop for each of the three species. Correlation between calorific values of each disc position and tree age was generally weak and dominantly negative for E. saligna and E. globulus, but positive for E. grandis. On the other hand, there was a weak but positive correlation between tree age and specific gravity and MOR for the three species. MOE was almost non-correlated with age. Generally, the results showed that waiting for older ages for the three Eucalyptus species may not further increase their calorific values. Hence, stands of the three Eucalyptus species can be harvested and used for fuelwood at an early age as traditionally managed on short-rotation basis. (author)

Analyses of Effects of Cutting Parameters on Cutting Edge Temperature Using Inverse Heat Conduction Technique

Directory of Open Access Journals (Sweden)

Marcelo Ribeiro dos Santos

2014-01-01

Full Text Available During machining energy is transformed into heat due to plastic deformation of the workpiece surface and friction between tool and workpiece. High temperatures are generated in the region of the cutting edge, which have a very important influence on wear rate of the cutting tool and on tool life. This work proposes the estimation of heat flux at the chip-tool interface using inverse techniques. Factors which influence the temperature distribution at the AISI M32C high speed steel tool rake face during machining of a ABNT 12L14 steel workpiece were also investigated. The temperature distribution was predicted using finite volume elements. A transient 3D numerical code using irregular and nonstaggered mesh was developed to solve the nonlinear heat diffusion equation. To validate the software, experimental tests were made. The inverse problem was solved using the function specification method. Heat fluxes at the tool-workpiece interface were estimated using inverse problems techniques and experimental temperatures. Tests were performed to study the effect of cutting parameters on cutting edge temperature. The results were compared with those of the tool-work thermocouple technique and a fair agreement was obtained.

Equilibrium Analysis in Cake Cutting

DEFF Research Database (Denmark)

Branzei, Simina; Miltersen, Peter Bro

2013-01-01

Cake cutting is a fundamental model in fair division; it represents the problem of fairly allocating a heterogeneous divisible good among agents with different preferences. The central criteria of fairness are proportionality and envy-freeness, and many of the existing protocols are designed...... to guarantee proportional or envy-free allocations, when the participating agents follow the protocol. However, typically, all agents following the protocol is not guaranteed to result in a Nash equilibrium. In this paper, we initiate the study of equilibria of classical cake cutting protocols. We consider one...... of the simplest and most elegant continuous algorithms -- the Dubins-Spanier procedure, which guarantees a proportional allocation of the cake -- and study its equilibria when the agents use simple threshold strategies. We show that given a cake cutting instance with strictly positive value density functions...

Influence of fast pyrolysis temperature on biochar labile fraction and short-term carbon loss in a loamy soil

International Nuclear Information System (INIS)

Bruun, Esben W.; Hauggaard-Nielsen, Henrik; Ibrahim, Norazana; Egsgaard, Helge; Ambus, Per; Jensen, Peter A.; Dam-Johansen, Kim

2011-01-01

Production of bio-oil, gas and biochar from pyrolysis of biomass is considered a promising technology for combined production of bioenergy and recalcitrant carbon (C) suitable for sequestration in soil. Using a fast pyrolysis centrifuge reactor (PCR) the present study investigated the relation between fast pyrolysis of wheat straw at different reactor temperatures and the short-term degradability of biochar in soil. After 115 days incubation 3-12% of the added biochar-C had been emitted as CO 2 . On average, 90% of the total biochar-C loss occurred within the first 20 days of the experiment, emphasizing the importance of knowing the biochar labile fraction when evaluating a specific biochars C sequestration potential. The pyrolysis temperature influenced the outputs of biochar, bio-oil and syngas significantly, as well as the stability of the biochar produced. Contrary to slow pyrolysis a fast pyrolysis process may result in incomplete conversion of biomass due to limitations to heat transfer and kinetics. In our case chemical analysis of the biochars revealed unconverted cellulosic and hemicellulosic fractions, which in turn were found to be proportional with the short-term biochar degradation in soil. As these labile carbohydrates are rapidly mineralized, their presence lowers the biochar-C sequestration potential. By raising the pyrolysis temperature, biochar with none or low contents of these fractions can be produced, but this will be on the expense of the biochar quantity. The yield of CO 2 neutral bio-oil is the other factor to optimize when adjusting the pyrolysis temperature settings to give the overall greatest climate change mitigation effect.

Reachability cuts for the vehicle routing problem with time windows

DEFF Research Database (Denmark)

Lysgaard, Jens

2004-01-01

This paper introduces a class of cuts, called reachability cuts, for the Vehicle Routing Problem with Time Windows (VRPTW). Reachability cuts are closely related to cuts derived from precedence constraints in the Asymmetric Traveling Salesman Problem with Time Windows and to k-path cuts...

Cutting weeds with a CO2 laser

DEFF Research Database (Denmark)

Heisel, T.; Schou, Jørgen; Christensen, S.

2001-01-01

Stems of Chenopodium album. and Sinapis arvensis. and leaves of Lolium perenne. were cut with a CO2 laser or with a pair of scissors. Treatments were carried out on greenhouse-grown pot plants at three different growth stages and at two heights. Plant dry matter was measured 2 to 5 weeks after...... treatment. The relationship between dry weight and laser energy was analysed using a non-linear dose-response regression model. The regression parameters differed significantly between the weed species. At all growth stages and heights S. arvensis was more difficult to cut with a CO2 laser than C. album....... When stems were cut below the meristems, 0.9 and 2.3 J mm(-1) of CO2 laser energy dose was sufficient to reduce by 90% the biomass of C. album and S. arvensis respectively. Regrowth appeared when dicotyledonous plant stems were cut above meristems, indicating that it is important to cut close...

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Len Volk; Mark Pickell; Evren Ozbayoglu; Barkim Demirdal; Paco Vieira; Affonso Lourenco

1999-10-15

This report includes a review of the progress made in ACTF Flow Loop development and research during 90 days pre-award period (May 15-July 14, 1999) and the following three months after the project approval date (July15-October 15, 1999) The report presents information on the following specific subjects; (a) Progress in Advanced Cuttings Transport Facility design and development, (b) Progress report on the research project ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress report on the research project ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress report on the research project ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress report on the research project ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Progress report on the instrumentation tasks (Tasks 11 and 12) (g) Activities towards technology transfer and developing contacts with oil and service company members.

High speed cutting of AZ31 magnesium alloy

Directory of Open Access Journals (Sweden)

Liwei Lu

2016-06-01

Full Text Available Using LBR-370 numerical control lathe, high speed cutting was applied to AZ31 magnesium alloy. The influence of cutting parameters on microstructure, surface roughness and machining hardening were investigated by using the methods of single factor and orthogonal experiment. The results show that the cutting parameters have an important effect on microstructure, surface roughness and machine hardening. The depth of stress layer, roughness and hardening present a declining tendency with the increase of the cutting speed and also increase with the augment of the cutting depth and feed rate. Moreover, we established a prediction model of the roughness, which has an important guidance on actual machining process of magnesium alloy.

Striation-free fibre laser cutting of mild steel sheets

Energy Technology Data Exchange (ETDEWEB)

Sobih, M.; Crouse, P.L.; Li, L. [University of Manchester, Laser Processing Research Centre, School of Mechanical, Aerospace and Civil Engineering, Sackville Street Building, P.O. Box 88, Manchester (United Kingdom)

2008-01-15

High-power laser cutting is extensively used in many industrial applications. An important weakness of this process is the formation of striations, i.e. regular lines on the cut surface, which lowers the quality of the surfaces produced. The elimination of striation formation is thus of considerable importance, since it could open a variety of novel high-precision applications. This study presents the initial results of a laser cutting study using a 1 kW single-mode fibre laser, a relative newcomer in the field of laser metal cutting. Striation-free laser cuts are demonstrated when cutting 1 mm thick mild steel sheets. (orig.)

The Role of Quantifier Alternations in Cut Elimination

DEFF Research Database (Denmark)

Gerhardy, Philipp

2005-01-01

Extending previous results on the complexity of cut elimination for the sequent calculus LK, we discuss the role of quantifier alternations and develop a measure to describe the complexity of cut elimination in terms of quantifier alternations in cut formulas and contractions on such formulas...

Study of AFM-based nanometric cutting process using molecular dynamics

International Nuclear Information System (INIS)

Zhu Pengzhe; Hu Yuanzhong; Ma Tianbao; Wang Hui

2010-01-01

Three-dimensional molecular dynamics (MD) simulations are conducted to investigate the atomic force microscope (AFM)-based nanometric cutting process of copper using diamond tool. The effects of tool geometry, cutting depth, cutting velocity and bulk temperature are studied. It is found that the tool geometry has a significant effect on the cutting resistance. The friction coefficient (cutting resistance) on the nanoscale decreases with the increase of tool angle as predicted by the macroscale theory. However, the friction coefficients on the nanoscale are bigger than those on the macroscale. The simulation results show that a bigger cutting depth results in more material deformation and larger chip volume, thus leading to bigger cutting force and bigger normal force. It is also observed that a higher cutting velocity results in a larger chip volume in front of the tool and bigger cutting force and normal force. The chip volume in front of the tool increases while the cutting force and normal force decrease with the increase of bulk temperature.

Development of cutting techniques of steel pipe by wire sawing

International Nuclear Information System (INIS)

Kamiyama, Yoshinori; Inai, Shinsuke

2004-01-01

A cutting method has a high cutting efficiency and enable cutting in safe. A wire saw cutting method is used for dismantling of massive concrete structures such as nuclear power plants with an effective and safe mean. In the case of dismantling of structures with multiple pipes installed at these facilities, an effective method is also demanded. If a wire saw method to remotely cut target objects in a large block in bulk is applicable, it will be expected an effective dismantling work under severe conditions with radioactivity. Although the wire saw method has adaptability for any shapes of cutting target objects and is widely adopted in dismantling of concrete constructs, it has few actual achievements in dismantling of steel structures such as steel pipe bundle. This study aims to verify its cutting characteristics and adaptability as a cutting method by conducting a cutting basic test to develop a diamond wire saw method to efficiently cut constructs with multiple pipes in a bundle. The test proved that a wire saw cutting method apply to dismantle structures with steel pipe bundle. A wire saw for metal cutting is adaptable in dismantling of bundle of thick carbon steel and stainless steel pipes. And also a wire saw for concrete cutting is adaptable in dismantling of pipe bundle structure with a mortar. (author)

Descriptive Analysis of In Vitro Cutting of Swine Mitral Cusps: Comparison of High-Power Laser and Scalpel Blade Cutting Techniques.

Science.gov (United States)

Pinto, Nathali Cordeiro; Pomerantzeff, Pablo Maria Alberto; Deana, Alessandro; Zezell, Denise; Benetti, Carolina; Aiello, Vera Demarchi; Lopes, Luciana Almeida; Jatene, Fabio Biscegli; Chavantes, M Cristina

2017-02-01

The most common injury to the heart valve with rheumatic involvement is mitral stenosis, which is the reason for a big number of cardiac operations in Brazil. Commissurotomy is the traditional technique that is still widely used for this condition, although late postoperative restenosis is concerning. This study's purpose was to compare the histological findings of porcine cusp mitral valves treated in vitro with commissurotomy with a scalpel blade to those treated with high-power laser (HPL) cutting, using appropriate staining techniques. Five mitral valves from healthy swine were randomly divided into two groups: Cusp group (G1), cut with a scalpel blade (n = 5), and Cusp group (G2), cut with a laser (n = 5). G2 cusps were treated using a diode laser (λ = 980 nm, power = 9.0 W, time = 12 sec, irradiance = 5625 W/cm 2 , and energy = 108 J). In G1, no histological change was observed in tissue. A hyaline basophilic aspect was focally observed in G2, along with a dark red color on the edges and areas of lower birefringence, when stained with hematoxylin-eosin, Masson's trichrome, and Sirius red. Further, the mean distances from the cutting edge in cusps submitted to laser application and stained with Masson's trichrome and Sirius red were 416.7 and 778.6 μm, respectively, never overcoming 1 mm in length. Thermal changes were unique in the group submitted to HPL and not observed in the cusp group cut with a scalpel blade. The mean distance of the cusps' collagen injury from the cutting edge was less than 1 mm with laser treatment. Additional studies are needed to establish the histological evolution of the laser cutting and to answer whether laser cutting may avoid valvular restenosis better than blade cutting.