WorldWideScience

Sample records for glenn refractory adhesive

  1. Arthroscopic treatment of refractory adhesive capsulitis of the shoulder

    Directory of Open Access Journals (Sweden)

    Marcos Rassi Fernandes

    Full Text Available OBJECTIVE: to evaluate the results of arthroscopic treatment of refractory adhesive capsulitis of the shoulder associated as for improved range of motion after a minimum follow up of six years. METHODS: from August 2002 to December 2004, ten patients with adhesive capsulitis of the shoulder resistant to conservative treatment underwent arthroscopic surgery. One interscalene catheter was placed for postoperative analgesia before the procedure. All were in Phase II, with a minimum follow up of two years. The mean age was 52.9 years (39-66, predominantly female (90%, six on the left shoulder. The time between onset of symptoms and surgical treatment ranged from six to 20 months. Four adhesive capsulitis were found to be primary (40% and six secondary (60%. RESULTS: the preoperative mean of active anterior elevation was 92°, of external rotation was 10.5° of the L5 level internal rotation; the postoperative ones were 149°, 40° and T12 level, respectively. Therefore, the average gain was 57° for the anterior elevation, 29.5° for external rotation in six spinous processes. There was a significant difference in movements' gains between the pre and post-operative periods (p<0.001. By the Constant Score (range of motion, there was an increase of 13.8 (average pre to 32 points (average post. CONCLUSION: the arthroscopic treatment proved effective in refractory adhesive capsulitis of the shoulder resistant to conservative treatment, improving the range of joint movements of patients evaluated after a minimum follow up of six years.

  2. Evaluation of the reusing of MGO-C refractory brick in refractory mixes

    International Nuclear Information System (INIS)

    Silva, R.D.S. da; Braganca, S.R.

    2012-01-01

    The residue from the use of MgO-C refractories in electric arc furnace presents, mostly, magnesium oxide in its composition and some slag contamination and impurities from the process of electrofusion scrap iron/steel. In this study, it was studied the characteristics of this residue and reused through its introduction into a commercial refractory mix, employed as material of coating and repair. This refractory mix was tested by thermogravimetric analysis, compressive strength, evaluation of plasticity and porosity as well as aspects of its installation, such as adhesion in situ. Results showed that there potential for reuse with the introduction of the waste in commercial mix was 30%, with little loss of compressive strength and plasticity. (author)

  3. Response to Glenn

    Directory of Open Access Journals (Sweden)

    Stephen Arons

    1998-01-01

    Full Text Available Arons responds to what he considers to be Glenn's misrepresentations of the tone and content of Short Route To Chaos. He writes that Glenn "appears to be attempting to construct the book's message into just one more salvo fired in the endless school wars. It is anything but....Reading Glenn's review, one is left with the impression that the book is a Christian-bashing, left-leaning, work of communitarian fuzziness in which a legal scholar unaccountably refuses to confine himself to ... technical explication of existing constitutional doctrine." In his response, Arons affirmatively sets out some of the book's main themes of political /cultural conflict over standardized schooling, corrects some of what he sees as Glenn's misunderstandings, and notes that the book itself invites readers to eschew partisanship and recognize that there are deep structural problems in American public education. In closing, Arons uses an example of Glenn's partisan misunderstanding that leads Arons to recommend to the reader that it would be better to read Short Route to Chaos for oneself.

  4. The effect of various sintering temperature on used refractory towards its physical properties

    Science.gov (United States)

    Sudibyo; Wulandari, Y. R.; Amin, M.; Azhar

    2018-01-01

    The used magnesia refractory from the kiln of cement industry was successfully recycled to new refractory using Kaolin as an adhesive. In this work, the temperatures of sintering were varied from 1000°C to 1500°C. The result shows that the increment temperature effects in sintering process will enhance refractory physical properties such as bulk density, cold crushing strength or pressure strength and thermal conductivity. Meanwhile, the porosity was decreased as the increase of the sintering temperature.

  5. Glenn Reconfigurable User-interface and Virtual reality Exploration (GURVE) Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The GRUVE (Glenn Reconfigurable User-interface and Virtual reality Exploration) Lab is a reconfigurable, large screen display facility at Nasa Glenn Research Center....

  6. Camera aboard 'Friendship 7' photographs John Glenn during spaceflight

    Science.gov (United States)

    1962-01-01

    A camera aboard the 'Friendship 7' Mercury spacecraft photographs Astronaut John H. Glenn Jr. during the Mercury-Atlas 6 spaceflight (00302-3); Photographs Glenn as he uses a photometer to view the sun during sunsent on the MA-6 space flight (00304).

  7. Historical Footage of John Glenn Friendship 7

    Science.gov (United States)

    1962-01-01

    The Friendship mission launch on the 20th day of February marked the first time that an American attempts to orbit the Earth. Historical footage of John Glenn's suit up, ride out to the launch pad, countdown, liftoff, booster engine cutoff, and separation of the booster engine escape tower is shown. Views of the Earth, Glenn's manual control of the electrical fly-by wire system, and the recovery of the landing vehicle from the ocean are presented.

  8. New Compressor Added to Glenn's 450- psig Combustion Air System

    Science.gov (United States)

    Swan, Jeffrey A.

    2000-01-01

    In September 1999, the Central Process Systems Engineering Branch and the Maintenance and the Central Process Systems Operations Branch, released for service a new high pressure compressor to supplement the 450-psig Combustion Air System at the NASA Glenn Research Center at Lewis Field. The new compressor, designated C-18, is located in Glenn s Central Air Equipment Building and is remotely operated from the Central Control Building. C-18 can provide 40 pounds per second (pps) of airflow at pressure to our research customers. This capability augments our existing system capacity (compressors C 4 at 38 pps and C-5 at 32 pps), which is generated from Glenn's Engine Research Building. The C-18 compressor was originally part of Glenn's 21-Inch Hypersonic Tunnel, which was transferred from the Jet Propulsion Laboratory to Glenn in the mid-1980's. With the investment of construction of facilities funding, the compressor was modified, new mechanical and electrical support equipment were purchased, and the unit was installed in the basement of the Central Air Equipment Building. After several weeks of checkout and troubleshooting, the new compressor was ready for long-term, reliable operations. With a total of 110 pps in airflow now available, Glenn is well positioned to support the high-pressure air test requirements of our research customers.

  9. Capsule-Preserving Hydrodilatation With Corticosteroid Versus Corticosteroid Injection Alone in Refractory Adhesive Capsulitis of Shoulder: A Randomized Controlled Trial.

    Science.gov (United States)

    Lee, Doo-Hyung; Yoon, Seung-Hyun; Lee, Michael Y; Kwack, Kyu-Sung; Rah, Ueon Woo

    2017-05-01

    To determine whether capsule-preserved hydrodilatation with corticosteroid improves pain and function in patients with refractory adhesive capsulitis (AC) better than intra-articular corticosteroid injection (IACI) alone. Prospective randomized controlled study. University-affiliated tertiary care hospital. Subjects with primary AC (N=64) with shoulder pain level of visual analog scale (VAS) score ≥5, even after the initial administration of IACI alone. Participants randomly received ultrasound-guided IACI alone with 1mL of 40mg/mL triamcinolone acetonide and 3mL of 1% lidocaine (n=32) or ultrasound-guided capsule-preserved hydrodilatation with corticosteroid with a mixture of 1mL of 40mg/mL triamcinolone acetonide, 6mL of 1% lidocaine, and normative saline (n=32). The primary outcome measure was the Shoulder Pain and Disability Index score. Secondary outcomes were the VAS of shoulder pain level and angles of shoulder passive range of motion, including flexion, abduction, extension, external rotation, and internal rotation at pretreatment and weeks 3, 6, and 12 of posttreatment. There were no significant differences between the 2 groups in terms of demographic characteristics (age, sex, duration of symptoms, shoulder affected, and body mass index) at baseline. Repeated-measures analysis of variance showed significant effect of time in all outcome measurements in both groups. However, group-by-time interactions were not significantly different for any of the outcomes between groups. This study shows that compared with pretreatment, all outcome measures improved significantly in both groups by time; however, there was no significant difference between the 2 groups. Therefore, we recommend IACI alone over capsule-preserved hydrodilatation with corticosteroid when considering the corticosteroid injection as a secondary option after the initial IACI fails to improve symptoms for patients with refractory AC. Copyright © 2016 American Congress of Rehabilitation

  10. Glenn's Strategic Partnerships With HBCUs and OMUs

    Science.gov (United States)

    Kankam, M. David

    2003-01-01

    NASA senior management has identified the need to develop a strategy for increased contracting with the historically black colleges and universities (HBCUs) and other minority universities (OMUs). The benefits to the institutions, by partnering with NASA, include developing their industrial base via NASA-industry partnerships, strong competitive advantage in technology-based research opportunities, and improved research capabilities. NASA gains increased contributed value to the Agency missions and programs as well as potential future recruits from technology-trained students who also constitute a pool for the nation s workforce. This report documents synergistic links between Glenn Research Center research and technology programs and faculty expertise at HBCUs and OMUs. The links are derived, based on Glenn technologies in the various directorates, program offices, and project offices. Such links readily identify universities with faculty members who are knowledgeable or have backgrounds in the listed technologies for possible collaboration. Recommendations are made to use the links as opportunities for Glenn and NASA, as well as industry collaborators, to cultivate stronger partnerships with the universities. It is concluded that Glenn and its partners and collaborators can expect to mutually benefit from leveraging NASA s cutting-edge and challenging research and technologies; industry's high technology development, research and development facilities, system design capabilities and market awareness; and academia s expertise in basic research and relatively low overhead cost. Reduced cost, accelerated technology development, technology transfer, and infrastructure development constitute some of the derived benefits.

  11. Response to Hayden and Glenn

    NARCIS (Netherlands)

    prof Berno van Meijel; Renate Verkaik; Miel Ribbe; Peter Spreeuwenberg; Anneke Francke; Josien Bensing

    2011-01-01

    We thank the authors Hayden and Glenn for commenting on our paper ‘The introduction of a nursing guideline on depression at psychogeriatric nursing home wards: Effects on Certified Nurse Assistants’, which was published in the International Journal of Nursing Studies (Verkaik et al., 2011). In our

  12. Astronaut John Glenn with artist who painted 'Friendship 7' on capsule

    Science.gov (United States)

    1962-01-01

    Astronaut John H. Glenn Jr., pilot of the Mercury-Atlas 6 'Friendship 7' mission, is suited up and seated beside his capsule during preflight activity at Cape Canaveral. Glenn is shown with artist Cecilia Bibby who painted the name 'Friendship 7' on his Mercury spacecraft.

  13. Astronaut Glenn in the Friendship 7

    Science.gov (United States)

    1962-01-01

    Astronaut John Glenn in the Friendship 7 capsule during the first manned orbital flight, the MA-6 mission. Boosted by the Mercury-Atlas vehicle, a modified Atlas (intercontinental ballistic missile), the MA-6 mission lasted for 5 hours and orbited the Earth three times.

  14. NASA Glenn Research Center Electrochemistry Branch Battery Overview

    Science.gov (United States)

    Manzo, Michelle A.

    2010-01-01

    This presentation covers an overview of NASA Glenn s history and heritage in the development of electrochemical systems for aerospace applications. Specific areas of focus are Li-ion batteries and their development for future Exploration missions. Current component development efforts for high energy and ultra high energy Li-ion batteries are addressed. Electrochemical systems are critical to the success of Exploration, Science and Space Operations missions. NASA Glenn has a long, successful heritage with batteries and fuel cells for aerospace applications. GRC Battery capabilities and expertise span basic research through flight hardware development and implementation. There is a great deal of synergy between energy storage system needs for aerospace and terrestrial applications.

  15. Slagging gasifier refractories. A new pathway to longer refractory life

    Energy Technology Data Exchange (ETDEWEB)

    Schnake, Mark [Harbinson-Walker Refractories Company, Mexico, MO (United States)

    2013-07-01

    Solid fuel slagging gasification to convert coal or petroleum coke feedstocks into syngas has rapidly evolved over the last 25 years. The gasifier is a high temperature, high pressure reaction chamber. Operating temperatures are between 1250 and 1575 C. Pressures will be between 20.4 and 68 atm. Syngas has been typically used for chemical feedstocks, fuel for power plants, or for steam and hydrogen generation in other industrial applications. Ash which comes from the solid fuel during gasification has many impurities. It melts during the gasifier reactor operation forming a liquid that penetrates the refractory lining. Given time, the refractory will wear away from thermal spalling, structural spalling, or overheating of the refractory. In some cases, all three wear mechanisms are seen in the same gasifier lining. Industry users have identified refractory life as one major limiting factor in worldwide use of this technology. Users have stated if the refractory liner can increase on-line availability of the gasifier operation, more industry acceptance of this technology is possible. Harbison-Walker Refractories Company will review destructive factors affecting lining life and discuss new refractory materials that have dramatically increased gasifier lining life and reliability. New refractory materials will be presented and supported by field trial results and post mortem analysis.

  16. Fluid Force-Induced Detachment Criteria for Nonmetallic Inclusions Adhered to a Refractory/Molten Steel Interface

    Science.gov (United States)

    Dieguez Salgado, Uxia; Weiß, Christian; Michelic, Susanne K.; Bernhard, Christian

    2018-05-01

    Since nonmetallic inclusions (NMIs) in steel cannot be completely avoided, a greater understanding of their development and evolution during the steelmaking process is required. In particular, this includes the adhesion of microinclusions to the refractory/steel interface in the flow control system between the tundish and the mold. This phenomenon, commonly referred to as clogging, causes losses in productivity and product quality. Inclusions transported from the bulk melt to the boundary layer may adhere to the refractory/steel interface due to formation of a fluid cavity. A detailed model was derived for the detachment of NMIs adhering to a nozzle wall and is based on the local hydrodynamic conditions combined with the specific interfacial properties in the system consisting of the inclusions, the refractories, and the steel. The model is evaluated for three different application-oriented cases. This study has been focused on providing a better understanding of fluid flow in the near-wall region in order to reduce clogging during steelmaking.

  17. High alumina refractories

    International Nuclear Information System (INIS)

    Simao, L.C.; Lopes, A.B.; Galvao Filho, N.B.; Souza, R.B. de

    1989-01-01

    High alumina refractories with 92 to 96.5% Al 2 O 3 were produced using brown and white fused as aggregate. Those refractories present only alumina-α and mullite as crystalline mineralogical phase. Other physical and chemical characteristics are similar to the ones found in refractories produced in Brazil, Japan and U.S.A. The most important physical and chemical tests used for the characterization of the raw materials and refractories, complemented by those realized at high temperatures, plus X-ray Difractometry and optical microscopy are presented, besides the refractory formulation and main parameters of production [pt

  18. John Glenn Biomedical Engineering Consortium

    Science.gov (United States)

    Nall, Marsha

    2004-01-01

    The John Glenn Biomedical Engineering Consortium is an inter-institutional research and technology development, beginning with ten projects in FY02 that are aimed at applying GRC expertise in fluid physics and sensor development with local biomedical expertise to mitigate the risks of space flight on the health, safety, and performance of astronauts. It is anticipated that several new technologies will be developed that are applicable to both medical needs in space and on earth.

  19. Collaborative Aerospace Research and Fellowship Program at NASA Glenn Research Center

    Science.gov (United States)

    Heyward, Ann O.; Kankam, Mark D.

    2004-01-01

    During the summer of 2004, a 10-week activity for university faculty entitled the NASA-OAI Collaborative Aerospace Research and Fellowship Program (CFP) was conducted at the NASA Glenn Research Center in collaboration with the Ohio Aerospace Institute (OAI). This is a companion program to the highly successful NASA Faculty Fellowship Program and its predecessor, the NASA-ASEE Summer Faculty Fellowship Program that operated for 38 years at Glenn. The objectives of CFP parallel those of its companion, viz., (1) to further the professional knowledge of qualified engineering and science faculty,(2) to stimulate an exchange of ideas between teaching participants and employees of NASA, (3) to enrich and refresh the research and teaching activities of participants institutions, and (4) to contribute to the research objectives of Glenn. However, CFP, unlike the NASA program, permits faculty to be in residence for more than two summers and does not limit participation to United States citizens. Selected fellows spend 10 weeks at Glenn working on research problems in collaboration with NASA colleagues and participating in related activities of the NASA-ASEE program. This year's program began officially on June 1, 2004 and continued through August 7, 2004. Several fellows had program dates that differed from the official dates because university schedules vary and because some of the summer research projects warranted a time extension beyond the 10 weeks for satisfactory completion of the work. The stipend paid to the fellows was $1200 per week and a relocation allowance of $1000 was paid to those living outside a 50-mile radius of the Center. In post-program surveys from this and previous years, the faculty cited numerous instances where participation in the program has led to new courses, new research projects, new laboratory experiments, and grants from NASA to continue the work initiated during the summer. Many of the fellows mentioned amplifying material, both in

  20. Merits of using andalusite-based refractories compared to bauxite-based refractories

    OpenAIRE

    Nyoka, M.; Brazier, D.; Courtney, T.; Parry, R.A.

    2013-01-01

    Historically bauxite-based refractories have been used in applications where andalusite-based refractories could work. Bauxite-based refractories were chosen over andalusite-based refractories mainly because of the availability of low-cost Chinese bauxite and also because many furnaces were designed by international companies that cannot easily access high-quality products. Currently, the availability of low-cost bauxite is under threat as a result of high export duties and tariffs as well as...

  1. Astronaut John Glenn Enters Friendship 7

    Science.gov (United States)

    1962-01-01

    Astronaut John Glenn enters the Mercury spacecraft, Friendship 7, prior to the launch of MA-6 on February 20, 1961 and became the first American who orbited the Earth. The MA-6 mission was the first manned orbital flight boosted by the Mercury-Atlas vehicle, a modified Atlas ICBM (Intercontinental Ballistic Missile), lasted for five hours, and orbited the Earth three times.

  2. High-Power Hall Propulsion Development at NASA Glenn Research Center

    Science.gov (United States)

    Kamhawi, Hani; Manzella, David H.; Smith, Timothy D.; Schmidt, George R.

    2014-01-01

    The NASA Office of the Chief Technologist Game Changing Division is sponsoring the development and testing of enabling technologies to achieve efficient and reliable human space exploration. High-power solar electric propulsion has been proposed by NASA's Human Exploration Framework Team as an option to achieve these ambitious missions to near Earth objects. NASA Glenn Research Center (NASA Glenn) is leading the development of mission concepts for a solar electric propulsion Technical Demonstration Mission. The mission concepts are highlighted in this paper but are detailed in a companion paper. There are also multiple projects that are developing technologies to support a demonstration mission and are also extensible to NASA's goals of human space exploration. Specifically, the In-Space Propulsion technology development project at NASA Glenn has a number of tasks related to high-power Hall thrusters including performance evaluation of existing Hall thrusters; performing detailed internal discharge chamber, near-field, and far-field plasma measurements; performing detailed physics-based modeling with the NASA Jet Propulsion Laboratory's Hall2De code; performing thermal and structural modeling; and developing high-power efficient discharge modules for power processing. This paper summarizes the various technology development tasks and progress made to date

  3. Refractory Materials for Flame Deflector Protection System Corrosion Control: Refractory Ceramics Literature Survey

    Science.gov (United States)

    Calle, Luz Marina; Hintze, Paul E.; Parlier, Christopher R.; Curran, Jerome P.; Kolody, Mark; Perusich, Stephen; Whitten, Mary C.; Trejo, David; Zidek, Jason; Sampson, Jeffrey W.; hide

    2009-01-01

    Ceramics can be defmed as a material consisting of hard brittle properties produced from inorganic and nonmetallic minerals made by firing at high temperatures. These materials are compounds between metallic and nonmetallic elements and are either totally ionic, or predominately ionic but having some covalent character. This definition allows for a large range of materials, not all applicable to refractory applications. As this report is focused on potential ceramic materials for high temperature, aggressive exposure applications, the ceramics reviewed as part of this report will focus on refractory ceramics specifically designed and used for these applications. Ceramic materials consist of a wide variety of products. Callister (2000) 1 characterized ceramic materials into six classifications: glasses, clay products, refractories, cements, abrasives, and advanced ceramics. Figure 1 shows this classification system. This review will focus mainly on refractory ceramics and cements as in general, the other classifications are neither applicable nor economical for use in large structures such as the flame trench. Although much work has been done in advanced ceramics over the past decade or so, these materials are likely cost prohibitive and would have to be fabricated off-site, transported to the NASA facilities, and installed, which make these even less feasible. Although the authors reviewed the literature on advanced ceramic refractories 2 center dot 3 center dot 4 center dot 5 center dot 6 center dot 7 center dot 8 center dot 9 center dot 10 center dot 11 center dot 12 after the review it was concluded that these materials should not be ' the focus of this report. A review is in progress on materials and systems for prefabricated refractory ceramic panels, but this review is focusing more on typical refractory materials for prefabricated systems, which could make the system more economically feasible. Refractory ceramics are used for a wide variety of applications

  4. Refractory vasculitis

    NARCIS (Netherlands)

    Rutgers, Bram; Kallenberg, Cees G. M.

    Refractory vasculitis occurs in 4-5% of patients with anti-neutrophil cytoplasmic antibody associated vasculitis (AAV). Differences between therapies used for refractory disease are mostly reflected in the percentages of complete and partial remissions, but also in the number of serious side

  5. The temperature of the boundary pig iron/refractory as variable to determine the corrosion mechanism of the blast furnace hearth

    International Nuclear Information System (INIS)

    Verdeja, L.F.; Alfonso, A.; Rusek, P.; Gonzalez, R.

    1998-01-01

    The wear of materials in the blast furnace could be carried out under the consideration of abrasion mechanisms or with the prevalence of the components chemistries and erosive resulting as of the circulation of flowing on the refractory. Nevertheless, although in determining situations the abrasion or the components chemistries could result the control mechanism, it is necessary to consider, that all the abrasion, erosion, chemical corrosion, adhesion and thermal waste-thermal shock they cooperate to the degradation of the refractory of blast furnace. For whatever the mechanisms that intervene in the wear of the materials, it results interesting to know the temperature boundary of the refractory with the solids, liquids or present gases in the furnace. In the report, it will be developed from specific form, the importance that has the temperature in the boundary refractory-pig iron on the wear of the materials of the hearth. The different hypothesis of transport (energy, quantity of movement and material) more adequate for the obtaining of the boundary temperatures will be discussed. (Author) 11 refs

  6. Pharmacotherapy for Refractory and Super-Refractory Status Epilepticus in Adults.

    Science.gov (United States)

    Holtkamp, Martin

    2018-03-01

    Patients with prolonged seizures that do not respond to intravenous benzodiazepines and a second-line anticonvulsant suffer from refractory status epilepticus and those with seizures that do not respond to continuous intravenous anesthetic anticonvulsants suffer from super-refractory status epilepticus. Both conditions are associated with significant morbidity and mortality. A strict pharmacological treatment regimen is urgently required, but the level of evidence for the available drugs is very low. Refractory complex focal status epilepticus generally does not require anesthetics, but all intravenous non-anesthetizing anticonvulsants may be used. Most descriptive data are available for levetiracetam, phenytoin and valproate. Refractory generalized convulsive status epilepticus is a life-threatening emergency, and long-term clinical consequences are eminent. Administration of intravenous anesthetics is mandatory, and drugs acting at the inhibitory gamma-aminobutyric acid (GABA) A receptor such as midazolam, propofol and thiopental/pentobarbital are recommended without preference for one of those. One in five patients with anesthetic treatment does not respond and has super-refractory status epilepticus. With sustained seizure activity, excitatory N-methyl-d-aspartate (NMDA) receptors are increasingly expressed post-synaptically. Ketamine is an antagonist at this receptor and may prove efficient in some patients at later stages. Neurosteroids such as allopregnanolone increase sensitivity at GABA A receptors; a Phase 1/2 trial demonstrated safety and tolerability, but randomized controlled data failed to demonstrate efficacy. Adjunct ketogenic diet may contribute to termination of difficult-to-treat status epilepticus. Randomized controlled trials are needed to increase evidence for treatment of refractory and super-refractory status epilepticus, but there are multiple obstacles for realization. Hitherto, prospective multicenter registries for pharmacological

  7. Special lecture in memory of Glenn Theodore Seaborg (19 April 1912 - 25 February 1999) Glenn T. Seaborg's multi-faceted career

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, Darleane C.

    2001-11-01

    Glenn Theodore Seaborg (1912-1999) was a world-renowned nuclear chemist, a Nobel Laureate in chemistry in 1951, co-discoverer of plutonium and nine other transuranium elements, Chairman of the US Atomic Energy Commission from 1961-71, scientific advisor to ten US presidents, active in national and international professional societies, an advocate for nuclear power as well as for a comprehensive nuclear test ban treaty, a prolific writer, an avid hiker, environmentalist, and sports enthusiast. He was known and esteemed not only by chemists and other scientists throughout the world, but also by lay people, politicians, statesmen, and students of all ages. This memorial includes a brief glimpse of Glenn Seaborg's early life and education, describes some of his major contributions to nuclear science over his long and fruitful career, and highlights his profound influence on nuclear science, both in the US and in the international community.

  8. Autoradiographic study of corrosion of refractories

    International Nuclear Information System (INIS)

    Lisenenkova, S.B.; Kucheryavyi, M.N.; Bursteva, T.A.

    1988-01-01

    A comparative study was made of the character of the interaction between a container-glass melt consisting of sodium calcium silicate and refractories in various furnace sections using an autoradiographic method. Static tests were conducted on specimens of the following refractories: chrome-aluminum-zircon, Bakor 41, corundum, a high alumina refractory, and a refractory based on tin dioxide. The specimens were activated by calcium 45. Autoradiography and photomicrography indicated that an intrinsic feature of all refractories was that calcium from the melt penetrated the refractories along the weak link; for fused-cast refractories, the glass phase; and for sintered refractories, through the binder and cracks

  9. Hemodynamic Effects of Ventricular Assist Device Implantation on Norwood, Glenn, and Fontan Circulation: A Simulation Study.

    Science.gov (United States)

    Di Molfetta, Arianna; Amodeo, Antonio; Gagliardi, Maria G; Trivella, Maria G; Fresiello, Libera; Filippelli, Sergio; Toscano, Alessandra; Ferrari, Gianfranco

    2016-01-01

    The growing population of failing single-ventricle (SV) patients might benefit from ventricular assist device (VAD) support as a bridge to heart transplantation. However, the documented experience is limited to isolated case reports. Considering the complex and different physiopathology of Norwood, Glenn, and Fontan patients and the lack of established experience, the aim of this work is to realize and test a lumped parameter model of the cardiovascular system able to simulate SV hemodynamics and VAD implantation effects to support clinical decision. Hemodynamic and echocardiographic data of 30 SV patients (10 Norwood, 10 Glenn, and 10 Fontan) were retrospectively collected and used to simulate patients' baseline. Then, the effects of VAD implantation were simulated. Simulation results suggest that the implantation of VAD: (i) increases the cardiac output and the mean arterial systemic pressure in all the three palliation conditions (Norwood 77.2 and 19.7%, Glenn 38.6 and 32.2%, and Fontan 17.2 and 14.2%); (ii) decreases the SV external work (Norwood 55%, Glenn 35.6%, and Fontan 41%); (iii) decreases the pressure pulsatility index (Norwood 65.2%, Glenn 81.3%, and Fontan 64.8%); (iv) increases the pulmonary arterial pressure in particular in the Norwood circulation (Norwood 39.7%, Glenn 12.1% and Fontan 3%); and (v) decreases the atrial pressure (Norwood 2%, Glenn 10.6%, and Fontan 8.6%). Finally, the VAD work is lower in the Norwood circulation (30.4 mL·mm Hg) in comparison with Fontan (40.3 mL·mm Hg) and to Glenn (64.5 mL·mm Hg) circulations. The use of VAD in SV physiology could be helpful to bridge patients to heart transplantations by increasing the CO and unloading the SV with a decrement of the atrial pressure and the SV external work. The regulation of the pulmonary flow is challenging because the Pap is increased by the presence of VAD. The hemodynamic changes are different in the different SV palliation step. The use of numerical models

  10. Obituary: R(oyal) Glenn Hall, 1921-2004

    Science.gov (United States)

    McCarthy, Dennis Dean

    2004-12-01

    R. Glenn Hall died on 25 June 2004 following a battle with prostate cancer. His contributions to the determination of the frequency corresponding to an energy level transition in the Cesium atom led to the definition of the length of the second and formed the basis for precise modern timekeeping. Glenn was born on 23 June 1921 in Koloa, Hawaii, and together with a brother and three sisters, grew up in Albion, Michigan. His father was a professor of political science at Albion College. He graduated from Park College in Parkville, Missouri with a degree in mathematics in 1941. He served as a corpsman in the U. S. Navy during World War II, and went on to earn a PhD at the University of Chicago in 1949. Glenn joined the faculty at the University of Chicago as an instructor from 1949 through 1952 and became a research associate there in 1953. While at the U. of Chicago he worked extensively on mass ratios of binary stars, binary star orbits and the determination of stellar parallaxes. In 1953 Glenn came to the U. S. Naval Observatory (USNO) where he became the Assistant Director of the Time Service Division. His early work at the Naval Observatory was related to the determination of Ephemeris Time (ET) from photographic observations of the Moon with respect to background stars. This work provided a time scale more uniform than that based on the Earth's rotation, which was the internationally accepted time scale at the time. As a result, the International Astronomical Union in 1955 redefined the second to be the second as determined from Ephemeris Time. In June 1955, L. Essen and J.V.L. Parry placed in operation a Cesium beam atomic standard at the National Physical Laboratory in Teddington, England. William Markowitz (1907-1998), the director of the Time Service, and Hall together with Essen and Parry then began the work leading to the determination of the frequency of the Cesium atom in terms of the second of the seasonally corrected time scale determined from the

  11. Refractoriness in human atria

    DEFF Research Database (Denmark)

    Skibsbye, Lasse; Jespersen, Thomas; Christ, Torsten

    2016-01-01

    BACKGROUND: Refractoriness of cardiac cells limits maximum frequency of electrical activity and protects the heart from tonic contractions. Short refractory periods support major arrhythmogenic substrates and augmentation of refractoriness is therefore seen as a main mechanism of antiarrhythmic...... drugs. Cardiomyocyte excitability depends on availability of sodium channels, which involves both time- and voltage-dependent recovery from inactivation. This study therefore aims to characterise how sodium channel inactivation affects refractoriness in human atria. METHODS AND RESULTS: Steady......-state activation and inactivation parameters of sodium channels measured in vitro in isolated human atrial cardiomyocytes were used to parameterise a mathematical human atrial cell model. Action potential data were acquired from human atrial trabeculae of patients in either sinus rhythm or chronic atrial...

  12. Plasma spraying of refractory metals and refractory hard materials. State of the art

    International Nuclear Information System (INIS)

    Eschnauer, H.; Lugscheider, E.; Jaeger, D.

    1989-01-01

    Suitable spraying processes for manufacturing refractory metals, refractory hard materials as well as spray materials with refractory components are the VPS- and IPS-spraying techniques. The advantages of these special spraying process variations are described. The reactive spraying materials are systematically organized. The characteristical properties used in purpose of improving the substrate surfaces are explained. Finally some examples of the latest results of research concerning plasma spraying of reactive materials are shown. 16 refs., 10 figs. (Author)

  13. Operação de Glenn bidirecional Bidirectional Glenn anastomosis

    Directory of Open Access Journals (Sweden)

    Paulo Chaccur

    1992-09-01

    Full Text Available A cirurgia de Gleen bidirecional tem sido empregadacomo uma opção ao tratamento cirúrgico de pacientes considerados candidatos "não ideais" à cirurgia de derivação átrio-pulmonar. A operação consiste na anastomose da veia cava superior com a artéria pulmonar (anastomose término-lateral, permitindo o fluxo sanguíneo também para o pulmão contra-lateral. A partir de janeiro de 1990 até fevereiro de 1992, 20 pacientes foram operados em nosso Serviço, com idade variando de 5 meses a 8 anos (média de 37,7 meses. Oito pacientes eram do sexo feminino e o peso variou de 6,3 a 18,8 Kg (média - 12,4 kg. A indicação cirúrgica foi considerada primária em 10 casos. Sete casos de atresia tricúspide e 3 de ventrículo único, que apresentavam acentuada diminuição do fluxo pulmonar e não eram candidatos a correção total funcional. Os demais pacientes tiveram a indicação considerada secundária, ou seja, já haviam sido submetidos a operação de shunt artério-venoso, cerclagem do tranco pulmonar, ou atriosseptostomia, 8 casos de atresia tricúspide, 3 de ventrículo único com estenose ou cerclagem pulmonar e 1 caso de DVSVD com ventrículo superior-inferior. A operação foi realizada com desvio da veia cava-átrio direito em 12 casos e com o uso de CEC em 8. Durante o procedimento cirúrgico, os pacientes foram monitorizados com oxímetro pulsátil e a saturação de oxigênio média pré-correção foi de 75,5% (71% a 86% e após, de 95% (91% a 98%. Não ocorreu óbito hospitalar e o único óbito tardio foi devido a infecção pulmonar no 2º mês de pós-operatório. Achamos, portanto, que a operação de Glenn bidirecional estará bem indicada como primeira etapa da correção definitiva, pois não aumenta o trabalho cardíaco e a resistência vascular pulmonar não produz distorções em artéria pulmonar como shunt tipo Blalock-Taussig.The bidirectional Glenn anastomosis has bee used as an effective mean of palliating

  14. Obituary: Glenn M. Frye (1926-2007)

    Science.gov (United States)

    Fickinger, William

    2011-12-01

    Glenn M. Frye, professor emeritus of physics at Case Western Reserve University, died in January 2007. His research interests at Case centered on the detection and identification of cosmic rays at the top of the atmosphere. Glenn was born in Michigan in 1926. He completed both his undergraduate and graduate studies at the University of Michigan. After earning his doctorate in 1950, he joined the nuclear physics research staff at Los Alamos Scientific Laboratory. Frye's research changed direction when he joined Fred Reines, who was also at LASL, in a cosmic ray experiment. In 1959, Reines moved east to become chair of the Case Institute of Technology physics department, and the following year Frye joined him there. The first years at Case Tech were devoted to the development of the rather complex spark chamber detectors which were destined to be suspended from high altitude balloons. Frye s experiments would be carried by the winds for hundreds of miles at altitudes greater than thirty miles, in both the northern and southern hemispheres. The maiden flights were launched in 1965 from the Palestine, Texas National Center for Atmospheric Research Balloon Base. The object was to search for gammas in the 30 to 500 MeV range coming from discrete point sources. Three years later the Frye team, along with collaborators from the University of Melbourne, reported success in this search. In a later Texas flight, high energy gammas were observed to come from the direction of the Crab Nebula, and, much more significantly, they arrived in the correct one millisecond bin of the known thirty millisecond period of the responsible pulsar. In later flights, involving ever more sophisticated detection schemes, Frye and his team collected valuable data on energetic gamma rays emitted by a dozen other sources. Through the 1970s and 1980s, they employed detectors with improved sensitivity and directionality to determine the energy distribution of cosmic gammas. With the participation of

  15. Aircraft Engine Noise Research and Testing at the NASA Glenn Research Center

    Science.gov (United States)

    Elliott, Dave

    2015-01-01

    The presentation will begin with a brief introduction to the NASA Glenn Research Center as well as an overview of how aircraft engine noise research fits within the organization. Some of the NASA programs and projects with noise content will be covered along with the associated goals of aircraft noise reduction. Topics covered within the noise research being presented will include noise prediction versus experimental results, along with engine fan, jet, and core noise. Details of the acoustic research conducted at NASA Glenn will include the test facilities available, recent test hardware, and data acquisition and analysis methods. Lastly some of the actual noise reduction methods investigated along with their results will be shown.

  16. Theoretical and practical aspects about corrosion of refractories used in steel metallurgy: part 3: characterization of commercial refractories

    International Nuclear Information System (INIS)

    Braganca, S.R.

    2012-01-01

    In this study, it was reviewed the main aspects found in the literature about refractories corrosion, evaluating the feasibility of certain tests and relating them with experimental results. The physical properties and microstructure of commercial refractories were analyzed, considering the differences between them and the quality implications and probable life of the refractory. Thus, it was studied the various types of refractories used as lining on steel ladle. Magnesia-carbon and doloma-carbon refractories were analyzed, highlighting the differences between them. The examined refractory showed characteristics favoring high resistance to corrosion process, presenting a series of properties to be selected in accordance with industry practice. (author)

  17. Impact of contributions of Glenn T. Seaborg on nuclear science

    International Nuclear Information System (INIS)

    Hoffman, Darleane C.

    2000-01-01

    Glenn Theodore Seaborg (1912-199) was a world-renowned nuclear chemist, a Nobel Laureate in chemistry in 1951, co-discoverer of plutonium and nine other transuranium elements, Chairman of the U.S. Atomic Energy Commission from 1961-71, scientific advisor to ten U.S. presidents, active in national and international professional societies, an advocate for nuclear power as well as for a comprehensive nuclear test ban treaty, a prolific writer, an avid hiker, environmentalist, and sports enthusiast. He was known and esteemed not only by chemists and other scientists throughout the world, but also by lay people, politicians, statesmen, and students of all ages. This memorial includes a brief glimpse of Glenn Seaborg's early life and education, describes some of his major contributions to nuclear science over his long and fruitful career, and highlights the profound impact of his contributions on nuclear science, both in the U.S. and in the international community

  18. Impact of contributions of Glenn T. Seaborg on nuclear science

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, Darleane C.

    2000-12-26

    Glenn Theodore Seaborg (1912-199) was a world-renowned nuclear chemist, a Nobel Laureate in chemistry in 1951, co-discoverer of plutonium and nine other transuranium elements, Chairman of the U.S. Atomic Energy Commission from 1961-71, scientific advisor to ten U.S. presidents, active in national and international professional societies, an advocate for nuclear power as well as for a comprehensive nuclear test ban treaty, a prolific writer, an avid hiker, environmentalist, and sports enthusiast. He was known and esteemed not only by chemists and other scientists throughout the world, but also by lay people, politicians, statesmen, and students of all ages. This memorial includes a brief glimpse of Glenn Seaborg's early life and education, describes some of his major contributions to nuclear science over his long and fruitful career, and highlights the profound impact of his contributions on nuclear science, both in the U.S. and in the international community.

  19. An Overview of the Antenna Measurement Facilities at the NASA Glenn Research Center

    Science.gov (United States)

    Lambert, Kevin M.; Anzic, Godfrey; Zakrajsek, Robert J.; Zaman, Afroz J.

    2002-10-01

    For the past twenty years, the NASA Glenn Research Center (formerly Lewis Research Center) in Cleveland, Ohio, has developed and maintained facilities for the evaluation of antennas. This effort has been in support of the work being done at the center in the research and development of space communication systems. The wide variety of antennas that have been considered for these systems resulted in a need for several types of antenna ranges at the Glenn Research Center. Four ranges, which are part of the Microwave Systems Laboratory, are the responsibility of the staff of the Applied RF Technology Branch. A general description of these ranges is provided in this paper.

  20. NASA Glenn Research Center Electrochemistry Branch Overview

    Science.gov (United States)

    Manzo, Michelle A.; Hoberecht, Mark; Reid, Concha

    2010-01-01

    This presentation covers an overview of NASA Glenn's history and heritage in the development of electrochemical systems for aerospace applications. Current programs related to batteries and fuel cells are addressed. Specific areas of focus are Li-ion batteries and Polymer Electrolyte Membrane Fuel cells systems and their development for future Exploration missions. The presentation covers details of current component development efforts for high energy and ultra high energy Li-ion batteries and non-flow-through fuel cell stack and balance of plant development. Electrochemistry Branch capabilities and facilities are also addressed.

  1. Compatibility of refractory materials with boiling sodium

    International Nuclear Information System (INIS)

    Meacham, S.A.

    1976-01-01

    The program employed to determine the compatibility of commercially available refractories with boiling sodium is described. The effects of impurities contained within the refractory material, and their relations with the refractory's physical stability are discussed. Also, since consideration of refractories for use as an insulating material within Liquid Metal Fast Breeder Reactor Plants (LMFBR's) is currently under investigation; recommendations, based upon this program, are presented

  2. REFRACTORY THROMBOCYTOPENIA AND NEUTROPENIA: A DIAGNOSTIC CHALLENGE

    OpenAIRE

    Emmanuel Gyan; François Dreyfus; Pierre Fenaux

    2015-01-01

    Background. The 2008 WHO classification identified refractory cytopenia with unilineage dysplasia (RCUD) as a composite entity encompassing refractory anemia, refractory thrombocytopenia (RT), and refractory neutropenia (RN), characterized by 10% or more dysplastic cells in the bone marrow respective lineage. The diagnosis of RT and RN is complicated by several factors.  Diagnosing RT first requires exclusion of familial thrombocytopenia, chronic auto-immune thrombocytopenia, concomitant medi...

  3. Overview of NASA Glenn Aero/Mobile Communications Demonstrations

    Science.gov (United States)

    Brooks, David; Hoder, Doug; Wilkins, Ryan

    2004-01-01

    The Glenn Research Center at Lewis Field (GRC) has been involved with several other NASA field centers on various networking and RF communications demonstrations and experiments since 1998. These collaborative experiments investigated communications technologies new to aviation, such as wideband Ku satcom, L-band narrowband satcom, and IP (Internet Protocol), using commercial off-the-shelf (COTS) components These technologies can be used to distribute weather and hazard data, air traffic management and airline fleet management information, and passenger cabin Internet service.

  4. Overview of NASA Glenn Aero/Mobile Communication Demonstrations

    Science.gov (United States)

    Brooks, David; Hoder, Doug; Wilkins, Ryan

    2004-01-01

    The Glenn Research Center at Lewis Field (GRC) has been involved with several other NASA field centers on various networking and RF communications demonstrations and experiments since 1998. These collaborative experiments investigated communications technologies new to aviation, such as wideband Ku satcom, L-band narrowband satcom, and IP (Internet Protocol), using commercial off-the-shelf (COTS) components These technologies can be used to distribute weather and hazard data, air traffic management and airline fleet management information, and passenger cabin Internet service.

  5. Refractory bin for burning

    Energy Technology Data Exchange (ETDEWEB)

    McPherson, D.L.; McPherson, T.L.

    1989-12-26

    This patent describes a refractory bin. It has a generally rectangular horizontal cross sectional configuration. It has wall structures each comprising an upper and a lower pair of elongated horizontal vertically spaced generally parallel support beams each having a vertical flange defining a support edge along its upper surface, a first generally rectangular refractory panel arranged with its lower edge at the bottom of the bin and with its outer surface in flat face contacting relation with the vertical flanges of the lower pair of support beams, a plurality of brackets each having a horizontal part and a vertical part and being secured to the outer surface of the first refractory panel.

  6. Talimogene Laherparepvec and Nivolumab in Treating Patients With Refractory Lymphomas or Advanced or Refractory Non-melanoma Skin Cancers

    Science.gov (United States)

    2018-05-21

    Adenoid Cystic Carcinoma; Adnexal Carcinoma; Apocrine Carcinoma; Eccrine Porocarcinoma; Extraocular Cutaneous Sebaceous Carcinoma; Hidradenocarcinoma; Keratoacanthoma; Malignant Sweat Gland Neoplasm; Merkel Cell Carcinoma; Microcystic Adnexal Carcinoma; NK-Cell Lymphoma, Unclassifiable; Non-Melanomatous Lesion; Paget Disease; Papillary Adenocarcinoma; Primary Cutaneous Mucinous Carcinoma; Refractory Anaplastic Large Cell Lymphoma; Refractory Mature T-Cell and NK-Cell Non-Hodgkin Lymphoma; Refractory Mycosis Fungoides; Refractory Primary Cutaneous T-Cell Non-Hodgkin Lymphoma; Refractory T-Cell Non-Hodgkin Lymphoma; Sezary Syndrome; Signet Ring Cell Carcinoma; Skin Basal Cell Carcinoma; Skin Basosquamous Cell Carcinoma; Skin Squamous Cell Carcinoma; Spiradenocarcinoma; Squamous Cell Carcinoma of Unknown Primary Origin; Stage III Skin Cancer; Stage IV Skin Cancer; Sweat Gland Carcinoma; Trichilemmocarcinoma; Vulvar Squamous Cell Carcinoma

  7. Friendship 7 the epic orbital flight of John H. Glenn, Jr.

    CERN Document Server

    Burgess, Colin

    2015-01-01

    In this spellbinding account of an historic but troubled orbital mission, noted space historian Colin Burgess takes us back to an electrifying time in American history, when intrepid pioneers were launched atop notoriously unreliable rockets at the very dawn of human space exploration.   A nation proudly and collectively came to a standstill on the day this mission flew; a day that will be forever enshrined in American spaceflight history. On the morning of February 20, 1962, following months of frustrating delays, a Marine Corps war hero and test pilot named John Glenn finally blazed a path into orbit aboard a compact capsule named Friendship 7.   The book’s tension-filled narrative faithfully unfolds through contemporary reports and the personal recollections of astronaut John Glenn, along with those closest to the Friendship 7 story, revealing previously unknown facts behind one of America’s most ambitious and memorable pioneering space missions.

  8. High Power MPD Thruster Development at the NASA Glenn Research Center

    Science.gov (United States)

    LaPointe, Michael R.; Mikellides, Pavlos G.; Reddy, Dhanireddy (Technical Monitor)

    2001-01-01

    Propulsion requirements for large platform orbit raising, cargo and piloted planetary missions, and robotic deep space exploration have rekindled interest in the development and deployment of high power electromagnetic thrusters. Magnetoplasmadynamic (MPD) thrusters can effectively process megawatts of power over a broad range of specific impulse values to meet these diverse in-space propulsion requirements. As NASA's lead center for electric propulsion, the Glenn Research Center has established an MW-class pulsed thruster test facility and is refurbishing a high-power steady-state facility to design, build, and test efficient gas-fed MPD thrusters. A complimentary numerical modeling effort based on the robust MACH2 code provides a well-balanced program of numerical analysis and experimental validation leading to improved high power MPD thruster performance. This paper reviews the current and planned experimental facilities and numerical modeling capabilities at the Glenn Research Center and outlines program plans for the development of new, efficient high power MPD thrusters.

  9. NASA Glenn Research Center Support of the Advanced Stirling Radioisotope Generator Project

    Science.gov (United States)

    Wilson, Scott D.; Wong, Wayne A.

    2015-01-01

    A high-efficiency radioisotope power system was being developed for long-duration NASA space science missions. The U.S. Department of Energy (DOE) managed a flight contract with Lockheed Martin Space Systems Company to build Advanced Stirling Radioisotope Generators (ASRGs), with support from NASA Glenn Research Center. DOE initiated termination of that contract in late 2013, primarily due to budget constraints. Sunpower, Inc., held two parallel contracts to produce Advanced Stirling Convertors (ASCs), one with Lockheed Martin to produce ASC-F flight units, and one with Glenn for the production of ASC-E3 engineering unit "pathfinders" that are built to the flight design. In support of those contracts, Glenn provided testing, materials expertise, Government-furnished equipment, inspection capabilities, and related data products to Lockheed Martin and Sunpower. The technical support included material evaluations, component tests, convertor characterization, and technology transfer. Material evaluations and component tests were performed on various ASC components in order to assess potential life-limiting mechanisms and provide data for reliability models. Convertor level tests were conducted to characterize performance under operating conditions that are representative of various mission conditions. Despite termination of the ASRG flight development contract, NASA continues to recognize the importance of high-efficiency ASC power conversion for Radioisotope Power Systems (RPS) and continues investment in the technology, including the continuation of the ASC-E3 contract. This paper describes key Government support for the ASRG project and future tests to be used to provide data for ongoing reliability assessments.

  10. The adhesive strength and initial viscosity of denture adhesives.

    Science.gov (United States)

    Han, Jian-Min; Hong, Guang; Dilinuer, Maimaitishawuti; Lin, Hong; Zheng, Gang; Wang, Xin-Zhi; Sasaki, Keiichi

    2014-11-01

    To examine the initial viscosity and adhesive strength of modern denture adhesives in vitro. Three cream-type denture adhesives (Poligrip S, Corect Cream, Liodent Cream; PGS, CRC, LDC) and three powder-type denture adhesives (Poligrip Powder, New Faston, Zanfton; PGP, FSN, ZFN) were used in this study. The initial viscosity was measured using a controlled-stress rheometer. The adhesive strength was measured according to ISO-10873 recommended procedures. All data were analyzed independently by one-way analysis of variance combined with a Student-Newman-Keuls multiple comparison test at a 5% level of significance. The initial viscosity of all the cream-type denture adhesives was lower than the powder-type adhesives. Before immersion in water, all the powder-type adhesives exhibited higher adhesive strength than the cream-type adhesives. However, the adhesive strength of cream-type denture adhesives increased significantly and exceeded the powder-type denture adhesives after immersion in water. For powder-type adhesives, the adhesive strength significantly decreased after immersion in water for 60 min, while the adhesive strength of the cream-type adhesives significantly decreased after immersion in water for 180 min. Cream-type denture adhesives have lower initial viscosity and higher adhesive strength than powder type adhesives, which may offer better manipulation properties and greater efficacy during application.

  11. Use of the novel hemostatic textile Stasilon® to arrest refractory retroperitoneal hemorrhage: a case report

    Directory of Open Access Journals (Sweden)

    Jones Samuel W

    2010-01-01

    Full Text Available Abstract Introduction Stasilon® is a novel hemostatic woven textile composed of allergen-free fibers of continuous filament fiberglass and bamboo yarn. The development of this product resulted from controlled in vitro thrombogenic analysis of an array of potentially hemostatic textile materials and it has been cleared for both external and internal use by the United States Food and Drug Administration for the arrest of hemorrhage. The goal of the study was to assess the hemostatic and adhesive properties of Stasilon® in the setting of life-threatening refractory hemorrhage. Case presentation A 39-year-old Caucasian man presented with severe necrotic pancreatitis that failed multiple aggressive attempts to control associated bleeding with electrocautery, suture ligation, and sequential anatomic packing with cotton-based sponges. Subsequent retroperitoneal packing with Stasilon® produced a non-adherent wound-dressing interface and resulted in the achievement of persistent hemostasis in the operative field. Conclusion In our patient, Stasilon® was demonstrated to be effective in the arrest of refractory hemorrhage.

  12. [The Engineering and Technical Services Directorate at the Glenn Research Center

    Science.gov (United States)

    Moon, James

    2004-01-01

    My name is James Moon and I am a senior at Tennessee State University where my major is Aeronautical and Industrial Technology with a concentration in industrial electronics. I am currently serving my internship in the Engineering and Technical Services Directorate at the Glenn Research Center (GRC). The Engineering and Technical Service Directorate provides the services and infrastructure for the Glenn Research Center to take research concepts to reality. They provide a full range of integrated services including engineering, advanced prototyping and testing, facility management, and information technology for NASA, industry, and academia. Engineering and Technical Services contains the core knowledge in Information Technology (IT). This includes data systems and analysis, inter and intranet based systems design and data security. Including the design and development of embedded real-time s o h a r e applications for flight and supporting ground systems, Engineering and Technical Services provide a wide range of IT services and products specific to the Glenn Research Center research and engineering community. In the 7000 Directorate I work directly in the 7611 organization. This organization is known as the Aviation Environments Technical Branch. My mentor is Vincent Satterwhite who is also the Branch Chief of the Aviation Environments Technical Branch. In this branch, I serve as the Assistant program manager of the Engineering Technology Program. The Engineering Technology Program (ETP) is one of three components of the High School L.E.R.C.I.P. This is an Agency-sponsored, eight-week research-based apprenticeship program designed to attract traditionally underrepresented high school students that demonstrate an aptitude for and interest in mathematics, science, engineering, and technology.

  13. Emergency Surgery for Refractory Status Epilepticus.

    Science.gov (United States)

    Botre, Abhijeet; Udani, Vrajesh; Desai, Neelu; Jagadish, Spoorthy; Sankhe, Milind

    2017-08-15

    Management of refractory status epilepticus in children is extremely challenging. Two children with medically refractory status epilepticus, both of whom had lesional pathology on MRI and concordant data on EEG and PET scan. Emergency hemispherotomy performed in both patients. A complete, sustained seizure freedom obtained postoperatively. Emergency surgery is a treatment option in selected cases of drug refractory status epilepticus with lesional pathology and concordant data.

  14. Updates in Refractory Status Epilepticus

    Science.gov (United States)

    Mahulikar, Advait; Suchdev, Kushak; Shah, Aashit

    2018-01-01

    Refractory status epilepticus is defined as persistent seizures despite appropriate use of two intravenous medications, one of which is a benzodiazepine. It can be seen in up to 40% of cases of status epilepticus with an acute symptomatic etiology as the most likely cause. New-onset refractory status epilepticus (NORSE) is a recently coined term for refractory status epilepticus where no apparent cause is found after initial testing. A large proportion of NORSE cases are eventually found to have an autoimmune etiology needing immunomodulatory treatment. Management of refractory status epilepticus involves treatment of an underlying etiology in addition to intravenous anesthetics and antiepileptic drugs. Alternative treatment options including diet therapies, electroconvulsive therapy, and surgical resection in case of a focal lesion should be considered. Short-term and long-term outcomes tend to be poor with significant morbidity and mortality with only one-third of patients reaching baseline neurological status. PMID:29854452

  15. Refractory status epilepticus

    Directory of Open Access Journals (Sweden)

    Sanjay P Singh

    2014-01-01

    Full Text Available Refractory status epilepticus is a potentially life-threatening medical emergency. It requires early diagnosis and treatment. There is a lack of consensus upon its semantic definition of whether it is status epilepticus that continues despite treatment with benzodiazepine and one antiepileptic medication (AED, i.e., Lorazepam + phenytoin. Others regard refractory status epilepticus as failure of benzodiazepine and 2 antiepileptic medications, i.e., Lorazepam + phenytoin + phenobarb. Up to 30% patients in SE fail to respond to two antiepileptic drugs (AEDs and 15% continue to have seizure activity despite use of three drugs. Mechanisms that have made the treatment even more challenging are GABA-R that is internalized during status epilepticus and upregulation of multidrug transporter proteins. All patients of refractory status epilepticus require continuous EEG monitoring. There are three main agents used in the treatment of RSE. These include pentobarbital or thiopental, midazolam and propofol. RSE was shown to result in mortality in 35% cases, 39.13% of patients were left with severe neurological deficits, while another 13% had mild neurological deficits.

  16. Refractory status epilepticus

    Science.gov (United States)

    Singh, Sanjay P; Agarwal, Shubhi; Faulkner, M

    2014-01-01

    Refractory status epilepticus is a potentially life-threatening medical emergency. It requires early diagnosis and treatment. There is a lack of consensus upon its semantic definition of whether it is status epilepticus that continues despite treatment with benzodiazepine and one antiepileptic medication (AED), i.e., Lorazepam + phenytoin. Others regard refractory status epilepticus as failure of benzodiazepine and 2 antiepileptic medications, i.e., Lorazepam + phenytoin + phenobarb. Up to 30% patients in SE fail to respond to two antiepileptic drugs (AEDs) and 15% continue to have seizure activity despite use of three drugs. Mechanisms that have made the treatment even more challenging are GABA-R that is internalized during status epilepticus and upregulation of multidrug transporter proteins. All patients of refractory status epilepticus require continuous EEG monitoring. There are three main agents used in the treatment of RSE. These include pentobarbital or thiopental, midazolam and propofol. RSE was shown to result in mortality in 35% cases, 39.13% of patients were left with severe neurological deficits, while another 13% had mild neurological deficits. PMID:24791086

  17. Wood : adhesives

    Science.gov (United States)

    A.H. Conner

    2001-01-01

    This chapter on wood adhesives includes: 1) Classification of wood adhesives 2) Thermosetting wood adhesives 3) Thermoplastic adhesives, 4) Wood adhesives based on natural sources 5) Nonconventional bonding of wood 6) Wood bonding.

  18. Development of refractory concrete for extreme conditions

    International Nuclear Information System (INIS)

    Pundiene, I; Antonovich, V; Stonys, R; Demidova-Buiziniene, I

    2011-01-01

    Comparative analysis is provided for the properties of medium-cement refractory concrete with microsilica based on mullite filler in relation to different type of deflocculant. The effect of different deflocculants on refractory concrete structure formation, hydration, rheology, strength and heat resistance is discussed. Corrosion resistance test, determined that samples with hybrid deflocculant showed better resistance for slag penetration than samples with only the sodium tripolyphosphate or polycarboxylate ether deflocculant. Moreover, a composition of hybrid deflocculant let to control the rate of the hydration process and to get features of refractory refractory concrete.

  19. High-Density Infrared Surface Treatments of Refractories

    Energy Technology Data Exchange (ETDEWEB)

    Tiegs, T.N.

    2005-03-31

    Refractory materials play a crucial role in all energy-intensive industries and are truly a crosscutting technology for the Industries of the Future (IOF). One of the major mechanisms for the degradation of refractories and a general decrease in their performance has been the penetration and corrosion by molten metals or glass. Methods and materials that would reduce the penetration, wetting, and corrosive chemistry would significantly improve refractory performance and also maintain the quality of the processed liquid, be it metal or glass. This report presents the results of an R&D project aimed at investigating the use of high-density infrared (HDI) heating to surface treat refractories to improve their performance. The project was a joint effort between Oak Ridge National Laboratory (ORNL) and the University of Missouri-Rolla (UMR). HDI is capable of heating the near-surface region of materials to very high temperatures where sintering, diffusion, and melting can occur. The intended benefits of HDI processing of refractories were to (1) reduce surface porosity (by essentially sealing the surface to prevent liquid penetration), (2) allow surface chemistry changes to be performed by bonding an adherent coating onto the underlying refractory (in order to inhibit wetting and/or improve corrosion resistance), and (3) produce noncontact refractories with high-emissivity surface coatings.

  20. Mullite-based coating on silicon carbide refractory obtained from PMSQ [poly(methylsilsesquioxane)

    International Nuclear Information System (INIS)

    Machado, Glauson Aparecido Ferreira

    2017-01-01

    Silicon carbide (SiC) presents low thermal expansion, high strength and thermal conductivity. For this reason it is used as kiln furniture for materials sintering. On the other hand, SiC degrades at high temperature under aggressive atmosphere. The use of protective coatings can avoid the right exposition of SiC surface to the furnace atmosphere. Mullite can be a suitable material as protective coating because of its high corrosion resistance and thermal expansion coefficient matching that of SiC (4,7 x 10 -6 /°C e 5,3 x 10 -6 /°C, respectively). In the present work a mullite coating obtained from ceramic precursor polymer and aluminium powder was studied to be applied over SiC refractories. Compositions were prepared with 10, 20, 30 and 50% (vol.) of aluminium powder added to the polymer. They were used aluminium powders with different distributions sizes These compositions were heat treated at different thermal cycles to determine a suitable condition to obtain a high mullite content. The composition with 20% of the smaller particle size Al powder was selected and used to be applied as a suspension over SiC refractory. The applied suspension, after dried, crosslinked and heat treated, formed a mullite coating over SiC refractory. Cycles of thermal shock were performed in coated and uncoated SiC samples to compare each other. They were carried out 26 cycles of thermal shock, in the following conditions: 600°C/30 min. and air cooling to room temperature. After each thermal shock, samples were analysed by mean of optical and electron microscopy, elastic modulus was also determined. After thermal shock cycles the coating presented good adhesion and no significant damage were observed. (author)

  1. Vernakalant selectively prolongs atrial refractoriness with no effect on ventricular refractoriness or defibrillation threshold in pigs.

    Science.gov (United States)

    Bechard, Jeff; Gibson, John Ken; Killingsworth, Cheryl R; Wheeler, Jeffery J; Schneidkraut, Marlowe J; Huang, Jian; Ideker, Raymond E; McAfee, Donald A

    2011-03-01

    Vernakalant is a novel antiarrhythmic agent that has demonstrated clinical efficacy for the treatment of atrial fibrillation. Vernakalant blocks, to various degrees, cardiac sodium and potassium channels with a pattern that suggests atrial selectivity. We hypothesized, therefore, that vernakalant would affect atrial more than ventricular effective refractory period (ERP) and have little or no effect on ventricular defibrillation threshold (DFT). Atrial and ventricular ERP and ventricular DFT were determined before and after treatment with vernakalant or vehicle in 23 anesthetized male mixed-breed pigs. Vernakalant was infused at a rate designed to achieve stable plasma levels similar to those in human clinical trials. Atrial and ventricular ERP were determined by endocardial extrastimuli delivered to the right atria or right ventricle. Defibrillation was achieved using external biphasic shocks delivered through adhesive defibrillation patches placed on the thorax after 10 seconds of electrically induced ventricular fibrillation. The DFT was estimated using the Dixon "up-and-down" method. Vernakalant significantly increased atrial ERP compared with vehicle controls (34 ± 8 versus 9 ± 7 msec, respectively) without significantly affecting ventricular ERP or DFT. This is consistent with atrial selective actions and supports the conclusion that vernakalant does not alter the efficacy of electrical defibrillation.

  2. Genetics Home Reference: iron-refractory iron deficiency anemia

    Science.gov (United States)

    ... refractory iron deficiency anemia Iron-refractory iron deficiency anemia Printable PDF Open All Close All Enable Javascript ... expand/collapse boxes. Description Iron-refractory iron deficiency anemia is one of many types of anemia , which ...

  3. Refractory hypertension: definition, prevalence, and patient characteristics.

    Science.gov (United States)

    Acelajado, Maria Czarina; Pisoni, Roberto; Dudenbostel, Tanja; Dell'Italia, Louis J; Cartmill, Falynn; Zhang, Bin; Cofield, Stacey S; Oparil, Suzanne; Calhoun, David A

    2012-01-01

    Among patients with resistant hypertension (RHTN), there are those whose blood pressure (BP) remains uncontrolled in spite of maximal medical therapy. This retrospective analysis aims to characterize these patients with refractory hypertension. Refractory hypertension was defined as BP that remained uncontrolled after ≥3 visits to a hypertension clinic within a minimum 6-month follow-up period. Of the 304 patients referred for RHTN, 29 (9.5%) remained refractory to treatment. Patients with refractory hypertension and those with controlled RHTN had similar aldosterone levels and plasma renin activity (PRA). Patients with refractory hypertension had higher baseline BP (175±23/97±15 mm Hg vs 158±25/89±15 mm Hg; P=.001/.005) and heart rate, and higher rates of prior stroke and congestive heart failure. During follow-up, the BP of patients with refractory hypertension remained uncontrolled (168.4±14.8/93.8±17.7 mm Hg) in spite of use of an average of 6 antihypertensive medications, while those of patients with controlled RHTN decreased to 129.3±11.2/77.6±10.8 mm Hg. Spironolactone reduced the BP by 12.9±17.8/6.6±13.7 mm Hg in patients with refractory hypertension and by 24.1±16.7/9.2±12.0 mm Hg in patients with controlled RHTN. In patients with RHTN, approximately 10% remain refractory to treatment. Similar aldosterone and PRA levels and a diminished response to spironolactone suggest that aldosterone excess does not explain the treatment failure. © 2011 Wiley Periodicals, Inc.

  4. Fabrication of smooth patterned structures of refractory metals, semiconductors, and oxides via template stripping.

    Science.gov (United States)

    Park, Jong Hyuk; Nagpal, Prashant; McPeak, Kevin M; Lindquist, Nathan C; Oh, Sang-Hyun; Norris, David J

    2013-10-09

    The template-stripping method can yield smooth patterned films without surface contamination. However, the process is typically limited to coinage metals such as silver and gold because other materials cannot be readily stripped from silicon templates due to strong adhesion. Herein, we report a more general template-stripping method that is applicable to a larger variety of materials, including refractory metals, semiconductors, and oxides. To address the adhesion issue, we introduce a thin gold layer between the template and the deposited materials. After peeling off the combined film from the template, the gold layer can be selectively removed via wet etching to reveal a smooth patterned structure of the desired material. Further, we demonstrate template-stripped multilayer structures that have potential applications for photovoltaics and solar absorbers. An entire patterned device, which can include a transparent conductor, semiconductor absorber, and back contact, can be fabricated. Since our approach can also produce many copies of the patterned structure with high fidelity by reusing the template, a low-cost and high-throughput process in micro- and nanofabrication is provided that is useful for electronics, plasmonics, and nanophotonics.

  5. Refractories for Industrial Processing. Opportunities for Improved Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, James G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hayden, H. Wayne [Metals Manufacture Process and Controls Technology, Inc., Oak Ridge, TN (United States); Angelini, Peter [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Moore, Robert E. [R.E. Moore Associates, Maricopa, AZ (United States); Headrick, William L. [R.E. Moore Associates, Maricopa, AZ (United States)

    2005-01-01

    Refractories are a class of materials of critical importance to manufacturing industries with high-temperature unit processes. This study describes industrial refractory applications and identifies refractory performance barriers to energy efficiency for processing. The report provides recommendations for R&D pathways leading to improved refractories for energy-efficient manufacturing and processing.

  6. NASA Glenn Research Center Experience with "LENR Phenomenon"

    Science.gov (United States)

    Wrbanek, Susan Y.; Fralick, Gustave C.; Wrbanek, John D.; Niedra, Janis M.

    2012-01-01

    Since 1989 NASA Glenn Research Center (GRC) has performed some small-scale limited experiments that show evidence of effects claimed by some to be evidence of Low Energy Nuclear Reactions (LENR). The research at GRC has involved observations and work on measurement techniques for observing the temperature effects in reactions of isotopes of hydrogen with palladium hydrides. The various experiments performed involved loading Pd with gaseous H2 and D2, and exposing Pd thin films to multi-bubble sonoluminescence in regular and deuterated water. An overview of these experiments and their results will be presented.

  7. NASA Glenn Research Center Experience with LENR Phenomenon

    Science.gov (United States)

    Wrbanek, Susan Y.; Fralick, Gustave C.; Wrbanek, John D.; Niedra, Janis M.

    2012-01-01

    Since 1989 NASA Glenn Research Center (GRC) has performed some small-scale limited experiments that show evidence of effects claimed by some to be evidence of Low Energy Nuclear Reactions (LENR). The research at GRC has involved observations and work on measurement techniques for observing the temperature effects in reactions of isotopes of hydrogen with palladium hydrides. The various experiments performed involved loading Pd with gaseous H2 and D2, and exposing Pd thin films to multi-bubble sonoluminescence in regular and deuterated water. An overview of these experiments and their results will be presented.

  8. 58. Actitud frente al flujo sanguíneo pulmonar adicional en la operación de glenn

    Directory of Open Access Journals (Sweden)

    F. Serrano Martínez

    2010-01-01

    Conclusiones: El mantenimiento de FPAC no incrementa la morbimortalidad post-Glenn ni altera la conservación funcional del ventrículo único, permitiendo llegar a la fase pre-Fontan con mayor SaO2 y mejor tamaño de ramas pulmonares. La existencia o ausencia de FPAC no influyó en los resultados del Fontan posterior, aunque consideramos interesante mantenerlo, especialmente en casos con ramas pulmonares pequeñas. La paliación pre-Glenn tipo banding pulmonar se asoció a mayor imposibilidad de conservar un FPAC.

  9. Cellular Adhesion and Adhesion Molecules

    OpenAIRE

    SELLER, Zerrin

    2014-01-01

    In recent years, cell adhesion and cell adhesion molecules have been shown to be important for many normal biological processes, including embryonic cell migration, immune system functions and wound healing. It has also been shown that they contribute to the pathogenesis of a large number of common human disorders, such as rheumatoid arthritis and tumor cell metastasis in cancer. In this review, the basic mechanisms of cellular adhesion and the structural and functional features of adhes...

  10. Education, Technology, and Media: A Peak into My Summer Internship at NASA Glenn Research Center in Cleveland, Ohio

    Science.gov (United States)

    Moon, James

    2004-01-01

    My name is James Moon and I am a senor at Tennessee State University where my major is Aeronautical and Industrial Technology with a concentration in industrial electronics. I am currently serving my internship in the Engineering and Technical Services Directorate at the Glenn Research Center (GRC). The Engineering and Technical Service Directorate provides the services and infrastructure for the Glenn Research Center to take research concepts to reality. They provide a full range of integrated services including engineering, advanced prototyping and testing, facility management, and information technology for NASA, industry, and academia. Engineering and Technical Services contains the core knowledge in Information Technology (IT). This includes data systems and analysis, inter and intranet based systems design and data security. Including the design and development of embedded real-time sohare applications for flight and supporting ground systems, Engineering and Technical Services provide a wide range of IT services and products specific to the Glenn Research Center research and engineering community.

  11. NASA Glenn Research Center Electrochemistry Branch Battery and Fuel Cell Development Overview

    Science.gov (United States)

    Manzo, Michelle A.

    2011-01-01

    This presentation covers an overview of NASA Glenn s history and heritage in the development of electrochemical systems for aerospace applications. Current developments related to batteries and fuel cells are addressed. Specific areas of focus are Li-ion batteries and Polymer Electrolyte Membrane Fuel cells systems and their development for future Exploration missions.

  12. Adhesion

    Science.gov (United States)

    ... Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Adhesion URL of this page: //medlineplus.gov/ency/article/001493.htm Adhesion To use the sharing features on this page, please enable JavaScript. Adhesions are bands of scar-like tissue that form between two ...

  13. Tungsten and refractory metals 3, proceedings

    International Nuclear Information System (INIS)

    Bose, A.; Dowding, R.J.

    1996-01-01

    The Third International Conference on Tungsten and Refractory Metals was held in Greater Washington DC at the McLean Hilton, McLean Virginia, on November 15--16, 1995. This meeting was the third in a series of conferences held in the Washington DC area. The first meeting was in 1992 and was entitled ''International Conference on Tungsten and Tungsten Alloys.'' In 1994, the scope of the meeting was expanded to include other refractory metals such as molybdenum, iridium, rhenium, tantalum and niobium. The tremendous success of that meeting was the primary motivation for this Conference. The broader scope (the inclusion of other refractory metals and alloys) of the Conference was kept intact for this meeting. In fact, it was felt that the developments in the technology of these materials required a common forum for the interchange of current research information. The papers presented in this meeting examined the rapid advancements in the technology of refractory metals, with special emphasis on the processing, structure, and properties. Among the properties there was emphasis on both quasi-static and dynamic rates. Another topic that received considerable interest was the area of refractory carbides and tungsten-copper composites. One day of concurrent session was necessary to accommodate all of the presentations

  14. Switchable Adhesion in Vacuum Using Bio-Inspired Dry Adhesives.

    Science.gov (United States)

    Purtov, Julia; Frensemeier, Mareike; Kroner, Elmar

    2015-11-04

    Suction based attachment systems for pick and place handling of fragile objects like glass plates or optical lenses are energy-consuming and noisy and fail at reduced air pressure, which is essential, e.g., in chemical and physical vapor deposition processes. Recently, an alternative approach toward reversible adhesion of sensitive objects based on bioinspired dry adhesive structures has emerged. There, the switching in adhesion is achieved by a reversible buckling of adhesive pillar structures. In this study, we demonstrate that these adhesives are capable of switching adhesion not only in ambient air conditions but also in vacuum. Our bioinspired patterned adhesive with an area of 1 cm(2) provided an adhesion force of 2.6 N ± 0.2 N in air, which was reduced to 1.9 N ± 0.2 N if measured in vacuum. Detachment was induced by buckling of the structures due to a high compressive preload and occurred, independent of air pressure, at approximately 0.9 N ± 0.1 N. The switch in adhesion was observed at a compressive preload between 5.6 and 6.0 N and was independent of air pressure. The difference between maximum adhesion force and adhesion force after buckling gives a reasonable window of operation for pick and place processes. High reversibility of the switching behavior is shown over 50 cycles in air and in vacuum, making the bioinspired switchable adhesive applicable for handling operations of fragile objects.

  15. John Glenn and rest of STS-95 crew exit Crew Transport Vehicle

    Science.gov (United States)

    1998-01-01

    Following touchdown at 12:04 p.m. EST at the Shuttle Landing Facility, the mission STS-95 crew leave the Crew Transport Vehicle. Payload Specialist John H. Glenn Jr. (center), a senator from Ohio, shakes hands with NASA Administrator Daniel S. Goldin. At left is Center Director Roy Bridges. Other crew members shown are Pilot Steven W. Lindsey (far left) and, behind Glenn, Mission Specialists Scott E. Parazynski and Stephen K. Robinson, and Payload Specialist Chiaki Mukai, Ph.D., M.D., with the National Space Development Agency of Japan. Not seen are Mission Commander Curtis L. Brown Jr. and Mission Specialist Pedro Duque of Spain, with the European Space Agency (ESA). The STS-95 crew completed a successful mission, landing at the Shuttle Landing Facility at 12:04 p.m. EST, after 9 days in space, traveling 3.6 million miles. The mission included research payloads such as the Spartan solar-observing deployable spacecraft, the Hubble Space Telescope Orbital Systems Test Platform, the International Extreme Ultraviolet Hitchhiker, as well as the SPACEHAB single module with experiments on space flight and the aging process.

  16. Potential refractory alloy requirements for space nuclear power applications

    International Nuclear Information System (INIS)

    Cooper, R.H. Jr.

    1984-01-01

    In reviewing design requirements for refractory alloys for space nuclear applications, several key points are identified. First, the successful utilization of refractory alloys is considered an enabling requirement for the successful deployment of high efficiency, lightweight, and small space nuclear systems. Second, the recapture of refractory alloy nuclear technology developed in the 1960s and early 1970s appears to be a pacing activity in the successful utilization of refractory alloys. Third, the successful application of refractory alloys for space nuclear applications will present a significant challenge to both the materials and the systems design communities

  17. Refractories for steel-works

    International Nuclear Information System (INIS)

    Villanova, R.A.; Galant, C.L.; Haas, C.; Rosenbaum, V.

    The routine procedures utilized for quality control of refractory materials used by PIRATINI's steel-works, are presented ' under an objetive and practical maner. The attention of the paper is concentrated upon the following' refractory types with higher consume: silicon-aluminous; aluminous; basic magnesia; basic chrom-magnesia. All steps of utilization are described, including specification, supplies programation, storage; sampling; physical tests, and also aplication procedures. Results from routine analysis during a six month period, by ' means of X-Ray Quantometry, using the fusion pearls procedure, are presented compared with Atomic Absorption [pt

  18. Development of AZS refractories for the glass industry

    International Nuclear Information System (INIS)

    Guzman, A.M.; Rodriguez, P.

    2004-01-01

    Refractory materials can support high temperatures, thermal strength and the contact with aggressive environments, for this reason they are widely used in the cement, glass and steel industry. Commercial AZS (alumina-zirconia-silica) refractories are a good alternative in refractory materials for the glass industry' because they can support the aggressive conditions during liquid processing of glass. However, another problem encountered in glass industry is contamination by refractory' material that fall into the molten glass, which can produce a series of defects in the final product. This research was conducted to develop new formulations of AZS refractories with different amounts of ZrO 2 with the purpose of improving the characteristics, properties and the work conditions in the glass melting furnaces and, at the same time, lower the costs this type of refractories. The results obtained indicate that the composition with low content of ZrO 2 can provide better properties than the commercial product, with some modifications in the particle size distribution. Copyright (2004) AD-TECH - International Foundation for the Advancement of Technology Ltd

  19. Refractory migraine in a headache clinic population

    Directory of Open Access Journals (Sweden)

    Fernandez-Torron Roberto

    2011-08-01

    Full Text Available Abstract Background Many migraineurs who seek care in headache clinics are refractory to treatment, despite advances in headache therapies. Epidemiology is poorly characterized, because diagnostic criteria for refractory migraine were not available until recently. We aimed to determine the frequency of refractory migraine in patients attended in the Headache Unit in a tertiary care center, according to recently proposed criteria. Methods The study population consisted of a consecutive sample of 370 patients (60.8% females with a mean age of 43 years (range 14-86 evaluated for the first time in our headache unit over a one-year period (between October 2008 and October 2009. We recorded information on clinical features, previous treatments, Migraine Disability Assessment Score (MIDAS, and final diagnosis. Results Overall migraine and tension-type headache were found in 46.4% and 20.5% of patients, respectively. Refractory migraine was found in 5.1% of patients. In refractory migraineurs, the mean MIDAS score was 96, and 36.8% were medication-overusers. Conclusions Refractory migraine is a relatively common and very disabling condition between the patients attended in a headache unit. The proposed operational criteria may be useful in identifying those patients who require care in headache units, the selection of candidates for combinations of prophylactic drugs or invasive treatments such as neurostimulation, but also to facilitate clinical studies in this patient group.

  20. NOvel Refractory Materials for High Alkali, High Temperature Environments

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, J.G.; Griffin, R. (MINTEQ International, Inc.)

    2011-08-30

    Refractory materials can be limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel was in service. The objective of this project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al2O3 spinel or other similar magnesia/alumina containing unshaped refractory composition (castables, gunnables, shotcretes, etc) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, highalkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. A research team was formed to carry out the proposed work led by Oak Ridge National Laboratory (ORNL) and was comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The two goals of this project were to produce novel refractory compositions which will allow for improved energy efficiency and to develop new refractory application techniques which would improve the speed of installation. Also methods of hot installation were sought which would allow for hot repairs and on-line maintenance leading to reduced process downtimes and eliminating the need to cool and reheat process vessels.

  1. In-Space Repair and Refurbishment of Thermal Protection System Structures for Reusable Launch Vehicles

    Science.gov (United States)

    Singh, M.

    2007-01-01

    Advanced repair and refurbishment technologies are critically needed for the thermal protection system of current space transportation systems as well as for future launch and crew return vehicles. There is a history of damage to these systems from impact during ground handling or ice during launch. In addition, there exists the potential for in-orbit damage from micrometeoroid and orbital debris impact as well as different factors (weather, launch acoustics, shearing, etc.) during launch and re-entry. The GRC developed GRABER (Glenn Refractory Adhesive for Bonding and Exterior Repair) material has shown multiuse capability for repair of small cracks and damage in reinforced carbon-carbon (RCC) material. The concept consists of preparing an adhesive paste of desired ceramic with appropriate additives and then applying the paste to the damaged/cracked area of the RCC composites with an adhesive delivery system. The adhesive paste cures at 100-120 C and transforms into a high temperature ceramic during reentry conditions. A number of plasma torch and ArcJet tests were carried out to evaluate the crack repair capability of GRABER materials for Reinforced Carbon-Carbon (RCC) composites. For the large area repair applications, Integrated Systems for Tile and Leading Edge Repair (InSTALER) have been developed and evaluated under various ArcJet testing conditions. In this presentation, performance of the repair materials as applied to RCC is discussed. Additionally, critical in-space repair needs and technical challenges are reviewed.

  2. In-Space Repair of Reinforced Carbon-Carbon Thermal Protection System Structures

    Science.gov (United States)

    Singh, Mrityunjay

    2006-01-01

    Advanced repair and refurbishment technologies are critically needed for the thermal protection system of current space transportation system as well as for future Crew Exploration Vehicles (CEV). The damage to these components could be caused by impact during ground handling or due to falling of ice or other objects during launch. In addition, in-orbit damage includes micrometeoroid and orbital debris impact as well as different factors (weather, launch acoustics, shearing, etc.) during launch and re-entry. The GRC developed GRABER (Glenn Refractory Adhesive for Bonding and Exterior Repair) material has shown multiuse capability for repair of small cracks and damage in reinforced carbon-carbon (RCC) material. The concept consists of preparing an adhesive paste of desired ceramic with appropriate additives and then applying the paste to the damaged/cracked area of the RCC composites with adhesive delivery system. The adhesive paste cures at 100-120 C and transforms into a high temperature ceramic during simulated entry conditions. A number of plasma torch and ArcJet tests were carried out to evaluate the crack repair capability of GRABER materials for Reinforced Carbon-Carbon (RCC) composites. For the large area repair applications, integrated system for tile and leading edge repair (InSTALER) have been developed. In this presentation, critical in-space repair needs and technical challenges as well as various issues and complexities will be discussed along with the plasma performance and post test characterization of repaired RCC materials.

  3. Effect of race on the timing of the Glenn and Fontan procedures for single-ventricle congenital heart disease.

    Science.gov (United States)

    Ingaramo, Oscar A; Khemani, Robinder G; Markovitz, Barry P; Epstein, David

    2012-03-01

    Disparities in health care have been documented between different racial groups in the United States. We hypothesize that there will be racial variance in the timing of the Glenn and Fontan procedures for children with single-ventricle physiology. We performed a retrospective review of a national pediatric intensive care unit database (Virtual PICU Performance System, LLC). Children with hypoplastic left heart syndrome, tricuspid atresia, and common ventricle, admitted from January 2006 to July 2008, were included. Data included race, weight, age, medical length of stay, Paediatric Index of Mortality 2 score, and survival. None. There were 423 patients from 29 hospitals. The study population was 7.6% black, 13.0% Hispanic, 59.8% white, 9.2% "other," and 11.6% had missing racial/ethnic information. Diagnoses included 255 patients with hypoplastic left heart syndrome, 91 with tricuspid atresia, and 77 with common ventricle. The median age for the Glenn procedure (n = 205) was 5.5 months (interquartile range, 4.6-7.0 months) and 39.7 months (interquartile range, 32.4-50.6 months) for the Fontan procedure (n = 218). There was no difference between the median age at the time of the Glenn or Fontan procedures between the different racial/ethnic groups (p = .65 and p = .16, respectively). The medical length of intensive care unit stay for patients receiving the Glenn and Fontan procedures was 3.7 days (interquartile range, 1.9-6.1 days) and 3.7 days (interquartile range, 1.9-6.8 days), respectively. There were no differences in medical length of intensive care unit stay for the Glenn procedure between the different racial/ethnic groups (p = .21). Hispanic patients had a longer medical length of intensive care unit stay (6.3 days; interquartile range, 3.1-9.9 days) than white patients (2.9 days; interquartile range, 1.8-5.3 days) for the Fontan procedure (p = .008). The timing of single-ventricle palliative procedures was not affected by race/ethnicity.

  4. SINTERED REFRACTORY TUNGSTEN ALLOYS. Gesinterte hochschmelzende wolframlegierungen

    Energy Technology Data Exchange (ETDEWEB)

    Kieffer, R.; Sedlatschek, K.; Braun, H.

    1971-12-15

    Dependence of the melting point of the refractory metals on their positions in the periodic system - alloys of tungsten with other refractory metals - sintering of the alloys - processing of the alloys - technological properties.

  5. Stochastic histories of refractory interstellar dust

    International Nuclear Information System (INIS)

    Liffman, K.; Chayton, D.D.

    1988-01-01

    The authors calculate histories for refractory dust particles in the interstellar medium. The double purposes are to learn something of the properties of interstellar dust as a system and to evaluate with specific assumptions the cosmic chemical memory interpretation of a specific class of isotopic anomalies. They assemble the profile of a particle population from a large number of stochastic, or Monte Carlo, histories of single particles, which are necessarily taken to be independent with this approach. They specify probabilities for each of the events that may befall a given particle and unfold its history by a sequence of random numbers. They assume that refractory particles are created only by thermal condensation within stellar material during its ejection from stars, and that these refractory particles can be destroyed only by being sputtered to a size too small for stability or by being incorporated into the formation of new stars. In order to record chemical detail, the authors take each new refractory particle to consist of a superrefractory core plus a more massive refractory mantle. They demonstrate that these superrefractory cores have effective lifetimes much longer than the turnover time of dust mass against sputtering. As examples of cosmic chemical memory they evaluate the 16 O-richness of interstellar aluminum and mechanisms for the 48 Ca/ 50 Ti correlation. Several related consequences of this approach are discussed

  6. A modified Glenn shunt reduces right ventricular stroke work during left ventricular assist device therapy.

    Science.gov (United States)

    Schiller, Petter; Vikholm, Per; Hellgren, Laila

    2016-03-01

    Right ventricular (RV) failure is a major cause of morbidity and mortality after left ventricular assist device (LVAD) placement and remains hard to predict. We hypothesized that partial surgical exclusion of the RV with a modified Glenn shunt during LVAD treatment would reduce RV stroke work. An LVAD was implanted in eight pigs and a modified Glenn shunt was constructed. A conductance pressure-volume catheter was placed in the right ventricle through the apex. Haemodynamic data and pressure-volume loops were obtained at the following time periods: (i) baseline, (ii) open shunt, (iii) LVAD with closed shunt and (iii) LVAD and open shunt. During LVAD therapy, the right atrial (RA) pressure increased from 9 mmHg (9-9) to 15 mmHg (12-15), P = 0.01. RV stroke volume increased from 30 ml (29-40) to 51 ml (42-53), P work increased to 708 mmHg ml (654-1193) from 535 mmHg ml (424-717), P = 0.04, compared with baseline. During LVAD therapy in combination with a Glenn shunt, the RA pressure decreased from 15 mmHg (12-15) to 10 mmHg (7-11) when compared with LVAD therapy only, P = 0.01. A decrease in RV stroke work from 708 mmHg ml (654-1193) to 465 mmHg ml (366-711), P = 0.04, was seen when the LVAD was combined with a shunt, not significantly different from the baseline value (535 mmHg ml). The developed pressure in the right ventricle decreased from 29 mmHg (26-32) to 21 mmHg (20-24), P work during the use of the shunt with LVAD treatment. A modified Glenn shunt reduced RV volumes, RV stroke work and RA pressure during LVAD therapy in an experimental model of heart failure in pigs. © The Author 2015. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

  7. Response properties of the refractory auditory nerve fiber.

    Science.gov (United States)

    Miller, C A; Abbas, P J; Robinson, B K

    2001-09-01

    The refractory characteristics of auditory nerve fibers limit their ability to accurately encode temporal information. Therefore, they are relevant to the design of cochlear prostheses. It is also possible that the refractory property could be exploited by prosthetic devices to improve information transfer, as refractoriness may enhance the nerve's stochastic properties. Furthermore, refractory data are needed for the development of accurate computational models of auditory nerve fibers. We applied a two-pulse forward-masking paradigm to a feline model of the human auditory nerve to assess refractory properties of single fibers. Each fiber was driven to refractoriness by a single (masker) current pulse delivered intracochlearly. Properties of firing efficiency, latency, jitter, spike amplitude, and relative spread (a measure of dynamic range and stochasticity) were examined by exciting fibers with a second (probe) pulse and systematically varying the masker-probe interval (MPI). Responses to monophasic cathodic current pulses were analyzed. We estimated the mean absolute refractory period to be about 330 micros and the mean recovery time constant to be about 410 micros. A significant proportion of fibers (13 of 34) responded to the probe pulse with MPIs as short as 500 micros. Spike amplitude decreased with decreasing MPI, a finding relevant to the development of computational nerve-fiber models, interpretation of gross evoked potentials, and models of more central neural processing. A small mean decrement in spike jitter was noted at small MPI values. Some trends (such as spike latency-vs-MPI) varied across fibers, suggesting that sites of excitation varied across fibers. Relative spread was found to increase with decreasing MPI values, providing direct evidence that stochastic properties of fibers are altered under conditions of refractoriness.

  8. Adhesion in microelectronics

    CERN Document Server

    Mittal, K L

    2014-01-01

    This comprehensive book will provide both fundamental and applied aspects of adhesion pertaining to microelectronics in a single and easily accessible source. Among the topics to be covered include; Various theories or mechanisms of adhesionSurface (physical or chemical) characterization of materials as it pertains to adhesionSurface cleaning as it pertains to adhesionWays to improve adhesionUnraveling of interfacial interactions using an array of pertinent techniquesCharacterization of interfaces / interphasesPolymer-polymer adhesionMetal-polymer adhesion  (metallized polymers)Polymer adhesi

  9. Refractory alloy technology for space nuclear power applications

    International Nuclear Information System (INIS)

    Cooper, R.H. Jr.; Hoffman, E.E.

    1984-01-01

    Purpose of this symposium is twofold: (1) to review and document the status of refractory alloy technology for structural and fuel-cladding applications in space nuclear power systems, and (2) to identify and document the refractory alloy research and development needs for the SP-100 Program in both the short and the long term. In this symposium, an effort was made to recapture the space reactor refractory alloy technology that was cut off in midstream around 1973 when the national space nuclear reactor program began in the early 1960s, was terminated. The six technical areas covered in the program are compatibility, processing and production, welding and component fabrication, mechanical and physical properties, effects of irradiation, and machinability. The refractory alloys considered are niobium, molybdenum, tantalum, and tungsten. Thirteen of the 14 pages have been abstracted separately. The remaining paper summarizes key needs for further R and D on refractory alloys

  10. An investigation into mineral processing of north Semnan refractory earth

    International Nuclear Information System (INIS)

    Aslani, S.; Samin-Bani-Hashemi, H.R.; Taghi-Zadeh, O.

    2002-01-01

    This paper is dealing with refractory earth of North Semnan. Having an area of 2000 square kilometers, Semnan province is mainly formed by sedimentary rocks with a verity of refractory earth, red earth and kaolin containing heavy minerals. The refractory earth of this area contains a considerable rate of aluminum oxide in shape of dia spore minerals, behemoth and gybsite along with heavy minerals of iron and titanium. To improve the quality of refractory earth, in order to be used in related industries, these minerals have to be separated. To assess the quality of refractory earth of North Semnan as the raw materials of refractory industries, their genesis and mineralogy properties have been precisely studied. Based on the rate of aluminium oxide of the refractory earth of North Semnan mines, a suitable mineral deposit has been selected for more investigation. Using XRD and X RF methods along with electronic and photo microscopes, the refractory earth and heavy minerals of them have been assessed. The elementary laboratory experiments of fragmentation and magnetic separation have been performed. It has been proved that the iron minerals can be separated and, therefore, the quality of the refractory earth can be improved. The separation of titanium minerals has to be investigated with other methods

  11. Treatment of refractory epilepsy with natalizumab in a patient with multiple sclerosis. Case report

    Directory of Open Access Journals (Sweden)

    Constantin Gabriela

    2010-09-01

    Full Text Available Abstract Background Multiple sclerosis (MS is considered an autoimmune disease of the central nervous system and therapeutic inhibition of leukocyte migration with natalizumab, an anti-alpha4 integrin antibody, is highly effective in patients with MS. Recent studies performed in experimental animal models with relevance to human disease suggested a key role for blood-brain barrier damage and leukocyte trafficking mechanisms also in the pathogenesis of epilepsy. In addition, vascular alterations and increased leukocyte accumulation into the brain were recently documented in patients with refractory epilepsy independently on the disease etiology. Case report Here we describe the clinical course of a 24-year-old patient with MS in whom abrupt tonic-clonic generalized seizures manifested at disease onset. Although MS had a more favorable course, treatment with glatiramer acetate and antiepileptic drugs for 7 years had no control on seizure generation and the patient developed severe refractory epilepsy. Interestingly, generalized seizures preceded new MS relapses suggesting that seizure activity may contribute to MS worsening creating a positive feedback loop between the two disease conditions. Notably, treatment with natalizumab for 12 months improved MS condition and led to a dramatic reduction of seizures. Conclusion Our case report suggests that inhibition of leukocyte adhesion may represent a new potential therapeutic approach in epilepsy and complement the traditional therapy with anti-epileptic drugs.

  12. REFRACTORY THROMBOCYTOPENIA AND NEUTROPENIA: A DIAGNOSTIC CHALLENGE

    Directory of Open Access Journals (Sweden)

    Emmanuel Gyan

    2015-02-01

    Full Text Available Background. The 2008 WHO classification identified refractory cytopenia with unilineage dysplasia (RCUD as a composite entity encompassing refractory anemia, refractory thrombocytopenia (RT, and refractory neutropenia (RN, characterized by 10% or more dysplastic cells in the bone marrow respective lineage. The diagnosis of RT and RN is complicated by several factors.  Diagnosing RT first requires exclusion of familial thrombocytopenia, chronic auto-immune thrombocytopenia, concomitant medications, viral infections, or hypersplenism. Diagnosis of RN should also be made after ruling out differential diagnoses such as ethnic or familial neutropenia, as well as acquired, drug-induced, infection-related or malignancy-related neutropenia. An accurate quantification of dysplasia should be performed in order to distinguish RT or RN from the provisional entity named idiopathic cytopenia of unknown significance (ICUS. Cytogenetic analysis, and possibly in the future somatic mutation analysis (of genes most frequently mutated in MDS, and flow cytometry analysis aberrant antigen expression on myeloid cells may help in this differential diagnosis. Importantly, we and others found that, while isolated neutropenia and thrombocytopenia are not rare in MDS, those patients can generally be classified (according to WHO 2008 classification as refractory cytopenia with multilineage dysplasia or refractory anemia with excess blasts, while RT and RN (according to WHO 2008 are quite rare.These results suggest in particular that identification of RT and RN as distinct entities could be reconsidered in future WHO classification updates.

  13. Adhesion science

    CERN Document Server

    Comyn, John

    1997-01-01

    The use of adhesives is widespread and growing, and there are few modern artefacts, from the simple cereal packet, to the jumbo jet, that are without this means of joining. Adhesion Science provides an illuminating account of the science underlying the use of adhesives, a branch of chemical technology which is fundamental to the science of coatings and composite materials and to the performance of all types of bonded structures. This book guides the reader through the essential basic polymer science, and the chemistry of adhesives in use at present. It discusses surface preparation for adhesive bonding, and the use of primers and coupling agents. There is a detailed chapter on contact angles and what can be predicted from them. A simple guide on stress distribution joints and how this relates to testing is included. It also examines the interaction of adhesives and the environment, including an analysis of the resistance of joints to water, oxygen and ultra-violet light. Adhesion Science provides a comprehens...

  14. Glenn T. Seaborg and heavy ion nuclear science

    International Nuclear Information System (INIS)

    Loveland, W.

    1992-04-01

    Radiochemistry has played a limited but important role in the study of nucleus-nucleus collisions. Many of the important radiochemical studies have taken place in Seaborg's laboratory or in the laboratories of others who have spent time in Berkeley working with Glenn T. Seaborg. I will discuss studies of low energy deep inelastic reactions with special emphasis on charge equilibration, studies of the properties of heavy residues in intermediate energy nuclear collisions and studies of target fragmentation in relativistic and ultrarelativistic reactions. The emphasis will be on the unique information afforded by radiochemistry and the physical insight derived from radiochemical studies. Future roles of radiochemistry in heavy ion nuclear science also will be discussed

  15. Denture Adhesives

    Science.gov (United States)

    ... Devices Products and Medical Procedures Dental Devices Denture Adhesives Share Tweet Linkedin Pin it More sharing options ... Wearers Reporting Problems to the FDA Background Denture adhesives are pastes, powders or adhesive pads that may ...

  16. Refractory alloy technology for space nuclear power applications

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, R.H. Jr.; Hoffman, E.E. (eds.)

    1984-01-01

    Purpose of this symposium is twofold: (1) to review and document the status of refractory alloy technology for structural and fuel-cladding applications in space nuclear power systems, and (2) to identify and document the refractory alloy research and development needs for the SP-100 Program in both the short and the long term. In this symposium, an effort was made to recapture the space reactor refractory alloy technology that was cut off in midstream around 1973 when the national space nuclear reactor program began in the early 1960s, was terminated. The six technical areas covered in the program are compatibility, processing and production, welding and component fabrication, mechanical and physical properties, effects of irradiation, and machinability. The refractory alloys considered are niobium, molybdenum, tantalum, and tungsten. Thirteen of the 14 pages have been abstracted separately. The remaining paper summarizes key needs for further R and D on refractory alloys. (DLC)

  17. Integrated Micro-Power System (IMPS) Development at NASA Glenn Research Center

    Science.gov (United States)

    Wilt, David; Hepp, Aloysius; Moran, Matt; Jenkins, Phillip; Scheiman, David; Raffaelle, Ryne

    2003-01-01

    Glenn Research Center (GRC) has a long history of energy related technology developments for large space related power systems, including photovoltaics, thermo-mechanical energy conversion, electrochemical energy storage. mechanical energy storage, power management and distribution and power system design. Recently, many of these technologies have begun to be adapted for small, distributed power system applications or Integrated Micro-Power Systems (IMPS). This paper will describe the IMPS component and system demonstration efforts to date.

  18. Temperature and Thermal Stress Analysis of Refractory Products

    Directory of Open Access Journals (Sweden)

    Shaoyang Shi

    2013-05-01

    Full Text Available Firstly current status of temperature and thermal stress research of refractory product at home and aboard are analyzed. Finite element model of two classical refractory products is building by using APDL language. Distribution law of temperature and thermal stress of two typical refractory products-ladles and tundish are analyzed and their structures are optimized. Stress of optimal structure is dropped obviously, and operation life is increased effectively.

  19. Reversible adhesion switching of porous fibrillar adhesive pads by humidity.

    Science.gov (United States)

    Xue, Longjian; Kovalev, Alexander; Dening, Kirstin; Eichler-Volf, Anna; Eickmeier, Henning; Haase, Markus; Enke, Dirk; Steinhart, Martin; Gorb, Stanislav N

    2013-01-01

    We report reversible adhesion switching on porous fibrillar polystyrene-block-poly(2-vinyl pyridine) (PS-b-P2VP) adhesive pads by humidity changes. Adhesion at a relative humidity of 90% was more than nine times higher than at a relative humidity of 2%. On nonporous fibrillar adhesive pads of the same material, adhesion increased only by a factor of ~3.3. The switching performance remained unchanged in at least 10 successive high/low humidity cycles. Main origin of enhanced adhesion at high humidity is the humidity-induced decrease in the elastic modulus of the polar component P2VP rather than capillary force. The presence of spongelike continuous internal pore systems with walls consisting of P2VP significantly leveraged this effect. Fibrillar adhesive pads on which adhesion is switchable by humidity changes may be used for preconcentration of airborne particulates, pollutants, and germs combined with triggered surface cleaning.

  20. Improved Adhesion and Compliancy of Hierarchical Fibrillar Adhesives.

    Science.gov (United States)

    Li, Yasong; Gates, Byron D; Menon, Carlo

    2015-08-05

    The gecko relies on van der Waals forces to cling onto surfaces with a variety of topography and composition. The hierarchical fibrillar structures on their climbing feet, ranging from mesoscale to nanoscale, are hypothesized to be key elements for the animal to conquer both smooth and rough surfaces. An epoxy-based artificial hierarchical fibrillar adhesive was prepared to study the influence of the hierarchical structures on the properties of a dry adhesive. The presented experiments highlight the advantages of a hierarchical structure despite a reduction of overall density and aspect ratio of nanofibrils. In contrast to an adhesive containing only nanometer-size fibrils, the hierarchical fibrillar adhesives exhibited a higher adhesion force and better compliancy when tested on an identical substrate.

  1. Turbofan Noise Studied in Unique Model Research Program in NASA Glenn's 9- by 15-Foot Low-Speed Wind Tunnel

    Science.gov (United States)

    Hughes, Christopher E.

    2001-01-01

    A comprehensive aeroacoustic research program called the Source Diagnostic Test was recently concluded in NASA Glenn Research Center's 9- by 15-Foot Low Speed Wind Tunnel. The testing involved representatives from Glenn, NASA Langley Research Center, GE Aircraft Engines, and the Boeing Company. The technical objectives of this research were to identify the different source mechanisms of noise in a modern, high-bypass turbofan aircraft engine through scale-model testing and to make detailed acoustic and aerodynamic measurements to more fully understand the physics of how turbofan noise is generated.

  2. Comparative evaluation of the locally manufactured low-alumina fireclay refractories

    International Nuclear Information System (INIS)

    Mohammad, D.; Ahmed, W.; Khan, M.I.

    2007-01-01

    Properties of domestically produced low-alumina refractories commonly known as medium duty fireclay refractories were studied and a comparative evaluation was performed. Refractory properties such as density, porosity, cold strength, reheat change and deformation at high-temperature were determined. Significant differences were discovered between these products sold as medium duty fireclay refractories. One brand marketed as medium duty refractory was found to be too inferior to be designated as medium duty firebrick. Absence of any standards and lack of awareness on the part of users of the various test methods appear to be the cause of this situation. (author)

  3. Directed light fabrication of refractory metals and alloys

    International Nuclear Information System (INIS)

    Fonseca, J.C.; Lewis, G.K.; Dickerson, P.G.; Nemec, R.B.

    1999-01-01

    This report covers deposition of refractory pure metals and alloys using the Directed Light Fabrication (DLF) process and represents progress in depositing these materials through September 1998. In extending the DLF process technology to refractory metals for producing fully dense, structurally sound deposits, several problems have become evident. (1) Control of porosity in DLF-deposited refractory metal is difficult because of gases, apparently present in commercially purchased refractory metal powder starting materials. (2) The radiant heat from the molten pool during deposition melts the DLF powder feed nozzle. (3) The high reflectivity of molten refractory metals, at the Nd-YAG laser wavelength (1.06microm), produces damaging back reflections to the optical train and fiber optic delivery system that can terminate DLF processing. (4) The current limits on the maximum available laser power to prevent back reflection damage limit the parameter range available for densification of refractory metals. The work to date concentrated on niobium, W-25Re, and spherodized tungsten. Niobium samples, made from hydride-dehydride powder, had minimal gas porosity and the deposition parameters were optimized; however, test plates were not made at this time. W-25Re samples, containing sodium and potassium from a precipitation process, were made and porosity was a problem for all samples although minimized with some process parameters. Deposits made from potassium reduced tungsten that was plasma spherodized were made with minimized porosity. Results of this work indicate that further gas analysis of starting powders and de-gassing of starting powders and/or gas removal during deposition of refractory metals is required

  4. Stretchable, Adhesion-Tunable Dry Adhesive by Surface Wrinkling

    KAUST Repository

    Jeong, Hoon Eui

    2010-02-16

    We introduce a simple yet robust method of fabricating a stretchable, adhesion-tunable dry adhesive by combining replica molding and surface wrinkling. By utilizing a thin, wrinkled polydimethyl siloxane (PDMS) sheet with a thickness of 1 mm with built-in micropillars, active, dynamic control of normal and shear adhesion was achieved. Relatively strong normal (∼10.8 N/cm2) and shear adhesion (∼14.7 N/cm2) forces could be obtained for a fully extended (strained) PDMS sheet (prestrain of∼3%), whereas the forces could be rapidly reduced to nearly zero once the prestrain was released (prestrain of ∼0.5%). Moreover, durability tests demonstrated that the adhesion strength in both the normal and shear directions was maintained over more than 100 cycles of attachment and detachment. © 2010 American Chemical Society.

  5. Stretchable, Adhesion-Tunable Dry Adhesive by Surface Wrinkling

    KAUST Repository

    Jeong, Hoon Eui; Kwak, Moon Kyu; Suh, Kahp Y.

    2010-01-01

    We introduce a simple yet robust method of fabricating a stretchable, adhesion-tunable dry adhesive by combining replica molding and surface wrinkling. By utilizing a thin, wrinkled polydimethyl siloxane (PDMS) sheet with a thickness of 1 mm with built-in micropillars, active, dynamic control of normal and shear adhesion was achieved. Relatively strong normal (∼10.8 N/cm2) and shear adhesion (∼14.7 N/cm2) forces could be obtained for a fully extended (strained) PDMS sheet (prestrain of∼3%), whereas the forces could be rapidly reduced to nearly zero once the prestrain was released (prestrain of ∼0.5%). Moreover, durability tests demonstrated that the adhesion strength in both the normal and shear directions was maintained over more than 100 cycles of attachment and detachment. © 2010 American Chemical Society.

  6. Results From the John Glenn Biomedical Engineering Consortium. A Success Story for NASA and Northeast Ohio

    Science.gov (United States)

    Nall, Marsha M.; Barna, Gerald J.

    2009-01-01

    The John Glenn Biomedical Engineering Consortium was established by NASA in 2002 to formulate and implement an integrated, interdisciplinary research program to address risks faced by astronauts during long-duration space missions. The consortium is comprised of a preeminent team of Northeast Ohio institutions that include Case Western Reserve University, the Cleveland Clinic, University Hospitals Case Medical Center, The National Center for Space Exploration Research, and the NASA Glenn Research Center. The John Glenn Biomedical Engineering Consortium research is focused on fluid physics and sensor technology that addresses the critical risks to crew health, safety, and performance. Effectively utilizing the unique skills, capabilities and facilities of the consortium members is also of prime importance. Research efforts were initiated with a general call for proposals to the consortium members. The top proposals were selected for funding through a rigorous, peer review process. The review included participation from NASA's Johnson Space Center, which has programmatic responsibility for NASA's Human Research Program. The projects range in scope from delivery of prototype hardware to applied research that enables future development of advanced technology devices. All of the projects selected for funding have been completed and the results are summarized. Because of the success of the consortium, the member institutions have extended the original agreement to continue this highly effective research collaboration through 2011.

  7. Sixth NASA Glenn Research Center Propulsion Control and Diagnostics (PCD) Workshop

    Science.gov (United States)

    Litt, Jonathan S. (Compiler)

    2018-01-01

    The Intelligent Control and Autonomy Branch at NASA Glenn Research Center hosted the Sixth Propulsion Control and Diagnostics Workshop on August 22-24, 2017. The objectives of this workshop were to disseminate information about research being performed in support of NASA Aeronautics programs; get feedback from peers on the research; and identify opportunities for collaboration. There were presentations and posters by NASA researchers, Department of Defense representatives, and engine manufacturers on aspects of turbine engine modeling, control, and diagnostics.

  8. Machining refractory alloys: an overview

    International Nuclear Information System (INIS)

    Christopher, J.D.

    1984-01-01

    Nontraditional machining is a generic term for those material removal processes that differ drastically from the historic operations such as turning, milling, drilling, tapping, and grinding. The use of primary energy modes other than mechanical, such as thermal, electrical, and chemical, sets these operations apart and reinforces their nontraditional label. Several of these newer processes have been very successful in machining close tolerance parts from refractory materials. This paper provides a general overview of both traditional and nontraditional aspects of machining refractory materials. 11 figures, 7 tables

  9. Universal adhesives: the next evolution in adhesive dentistry?

    Science.gov (United States)

    Alex, Gary

    2015-01-01

    Every so often a new material, technique, or technological breakthrough spurs a paradigm shift in the way dentistry is practiced. The development and evolution of reliable enamel and dentin bonding agents is one such example. Indeed, the so-called "cosmetic revolution" in dentistry blossomed in large part due to dramatic advances in adhesive technology. It is the ability to bond various materials in a reasonably predictable fashion to both enamel and dentin substrates that enables dentists to routinely place porcelain veneers, direct and indirect composites, and a plethora of other restorative and esthetic materials. In fact, the longevity and predictability of many (if not most) current restorative procedures is wholly predicated on the dentist's ability to bond various materials to tooth tissues. Adhesive systems have progressed from the largely ineffective systems of the 1970s and early 1980s to the relatively successful total- and self-etching systems of today. The latest players in the adhesive marketplace are the so-called "universal adhesives." In theory, these systems have the potential to significantly simplify and expedite adhesive protocols and may indeed represent the next evolution in adhesive dentistry. But what defines a universal system, and are all these new systems truly "universal" and everything they are claimed to be? This article will examine the origin, chemistry, strengths, weaknesses, and clinical relevance of this new genre of dental adhesives.

  10. Production of lightweight refractory material by hydrothermal process

    International Nuclear Information System (INIS)

    Sulejmani, Ramiz B.

    2002-01-01

    Many different processes of production of lightweight refractories are well known over the World. Traditional production of lightweight refractories is by addition of combustibles or by a special frothing process. This work is concerned with hydrothermal of lightweight refractories from rice husk ash. The rice husk ash, used in present investigations were from Kocani region, R. Macedonia. The chemical analysis of the rice husk ash shows that it contains 91,8 - 93,7% SiO 2 and some alkaline and alkaline earth oxides. Microscopic and X - ray diffraction examinations of the rice husk ash have shown that it is composed of cristobalite, tridimite and amorphous silica. The composition of the mixture for lightweight refractory brick production is 93,4% rice husk ash and 6,6% Ca(OH) 2 . The mixtures were well mixed, moistened and pressed at 5 - 10 MPa. The hydrothermal reactions between calcium hydroxide and rice husk ash over the temperature range 80 - 160 o C were investigated. The period of autoclave treatment was from 2 to 72 h. After the hydrothermal treatment of the samples, the mineralogical composition, bulk density, density, cold crushing strength, porosity, refractoriness and thermal expansion were examined. Analysing the properties of the obtained samples it can be concluded that from rice husk ash and calcium hydroxide under hydrothermal condition it is possible to obtain lightweight acid refractory material with high quality.(Author)

  11. Directed light fabrication of refractory metals and alloys

    International Nuclear Information System (INIS)

    Fonseca, J.C.; Lewis, G.K.; Dickerson, P.G.; Nemec, R.B.

    1999-01-01

    This report covers work performed under Order No. FA0000020 AN Contract DE-AC12-76SN00052 for deposition of refractory pure metals and alloys using the Directed Light Fabrication (DLF) process and represents the progress in depositing these materials through September 1998. In extending the DLF process technology to refractory metals for producing fully dense, structurally sound deposits, several problems have become evident. 1. Control of porosity in DLF-deposited refractory metal is difficult because of gases, apparently present in commercially purchased refractory metal powder starting materials. 2. The radiant heat from the molten pool during deposition melts the DLF powder feed nozzle. 3. The high reflectivity of molten refractory metals, at the Nd-YAG laser wavelength (1.06microm), produces damaging back reflections to the optical train and fiber optic delivery system that can terminate DLF processing. 4. The current limits on the maximum available laser power to prevent back reflection damage limit the parameter range available for densification of refractory metals. The work to date concentrated on niobium, W-25Re, and spherodized tungsten. Niobium samples, made from hydride-dehydride powder, had minimal gas porosity and the deposition parameters were optimized; however, test plates were not made at this time. W-25Re samples, containing sodium and potassium from a precipitation process, were made and porosity was a problem for all samples although minimized with some process parameters. Deposits made from potassium reduced tungsten that was plasma spherodized were made with minimized porosity. Results of this work indicate that further gas analysis of starting powders and de-gassing of starting powders and/or gas removal during deposition of refractory metals is required

  12. Hydrogen-Oxygen PEM Regenerative Fuel Cell at NASA Glenn Research Center

    Science.gov (United States)

    Bents, David J.

    2004-01-01

    The NASA Glenn Research Center has constructed a closed-cycle hydrogen-oxygen PEM regenerative fuel cell (RFC) to explore its potential use as an energy storage device for a high altitude solar electric aircraft. Built up over the last 2 years from specialized hardware and off the shelf components the Glenn RFC is a complete "brassboard" energy storage system which includes all the equipment required to (1) absorb electrical power from an outside source and store it as pressurized hydrogen and oxygen and (2) make electrical power from the stored gases, saving the product water for re-use during the next cycle. It consists of a dedicated hydrogen-oxygen fuel cell stack and an electrolyzer stack, the interconnecting plumbing and valves, cooling pumps, water transfer pumps, gas recirculation pumps, phase separators, storage tanks for oxygen (O2) and hydrogen (H2), heat exchangers, isolation valves, pressure regulators, nitrogen purge provisions, instrumentation, and other components. It specific developmental functions include: (1) Test fuel cells and fuel cell components under repeated closed-cycle operation (nothing escapes; everything is used over and over again). (2) Simulate diurnal charge-discharge cycles (3) Observe long-term system performance and identify degradation and loss mechanisms. (4) Develop safe and convenient operation and control strategies leading to the successful development of mission-capable, flight-weight RFC's.

  13. Spinning of refractory metals

    International Nuclear Information System (INIS)

    Chang Wenkua; Zheng Han

    1989-01-01

    The effects of spinning process parameters including max. pass percentage reduction, spinning temperature, feed rate, lubricant and annealing technology on the quality of shaped components are summarized and discussed in the present paper. The above mentioned parameters are adopted in the process of spinning of barrel-shaped and specially shaped components of refractory metals and their alloys W, Mo, Nb, Zr, TZM molybdenum alloy, C-103, C-752 niobium alloy etc. The cause of leading to usual defects of spun products of refractory metals such as lamellar as 'scaling', crack, swelling, wrinkle, etc. have been analysed and the ways to eliminate the defects have been put forward. 8 figs., 5 tabs. (Author)

  14. Migration of TRU-containing slag into candidate refractories for waste management

    International Nuclear Information System (INIS)

    Seymour, W.C.

    1978-11-01

    Results of initial tests on transuranic migration into commercial refractories are reported. Five castable refractories and a plastic-bonded refractory were tested using the cup test method. Initial results indicate that castable materials will not survive conditions expected in the slagging pyrolysis unit; plastic refractories appear to have better performance. The major mechanism of migration into the tested refractories is pore penetration. Al 2 O 3 and Al 2 O 3 -Cr 2 O 3 phases appear resistant to chemical diffusion of transuranics. 2 figures, 16 tables

  15. Refractory of Furnaces to Reduce Environmental Impact

    International Nuclear Information System (INIS)

    Hanzawa, Shigeru

    2011-01-01

    The energy load of furnaces used in the manufacturing process of ceramics is quite large. Most of the environmental impact of ceramics manufacturing is due to the CO 2 produced from this high energy load. To improve this situation, R and D has focused on furnace systems and techniques of control in order to reduce energy load. Since furnaces are comprised of refractory, consideration of their mechanical and thermal characteristics is important. Herein are described several refractory types which were chosen through comparison of the characteristics which contribute to heat capacity reduction, heat insulating reinforcement and high emissivity, thereby improving thermal radiation heat transfer efficiency to the ceramic articles. One selected refractory material which will reduce the environmental impact of a furnace, chosen considering low heat capacity and high emissivity characteristics, is SiC. In this study, thermal radiation heat transfer efficiency improvement and its effect on ceramic articles in the furnace and oxidation behaviour were investigated at 1700K. A high density SiC refractory, built into the furnace at construction, has relatively high oxidation durability and has the ability to reduce environmental impact-CO 2 by 10 percent by decreasing the furnace's energy load. However, new oxidation prevention techniques for SiC will be necessary for long-term use in industrial furnaces, because passive to active oxidation transition behaviour of commercial SiC refractory is coming to close ideal.

  16. Refractory of Furnaces to Reduce Environmental Impact

    Science.gov (United States)

    Hanzawa, Shigeru

    2011-10-01

    The energy load of furnaces used in the manufacturing process of ceramics is quite large. Most of the environmental impact of ceramics manufacturing is due to the CO2 produced from this high energy load. To improve this situation, R&D has focused on furnace systems and techniques of control in order to reduce energy load. Since furnaces are comprised of refractory, consideration of their mechanical and thermal characteristics is important. Herein are described several refractory types which were chosen through comparison of the characteristics which contribute to heat capacity reduction, heat insulating reinforcement and high emissivity, thereby improving thermal radiation heat transfer efficiency to the ceramic articles. One selected refractory material which will reduce the environmental impact of a furnace, chosen considering low heat capacity and high emissivity characteristics, is SiC. In this study, thermal radiation heat transfer efficiency improvement and its effect on ceramic articles in the furnace and oxidation behaviour were investigated at 1700K. A high density SiC refractory, built into the furnace at construction, has relatively high oxidation durability and has the ability to reduce environmental impact-CO2 by 10 percent by decreasing the furnace's energy load. However, new oxidation prevention techniques for SiC will be necessary for long-term use in industrial furnaces, because passive to active oxidation transition behaviour of commercial SiC refractory is coming to close ideal.

  17. Development of alumino-silicate refractories in Ghana

    International Nuclear Information System (INIS)

    Kisiedu, A. K.; Tetteh, D.M.B.; Obiri, H. A.; Brenya, E. F.; Ayensu, A.

    2008-01-01

    Alumino-silicate (bauxite), andalusite, kaolin and clay were investigated for suitability in production of alumina, mullite and fireclay brick refractories. The raw materials were characterized by X-ray diffraction, differential thermal and silicate analyses. The x-ray diffraction analysis of alumina and mullite refractories fired at 1450 0 C, and fireclay bricks fired at 1350 0 C, indicated presence of corundum and alpha-alumina crystals. The values of thermal (fired) shrinkage, crushing, strength, porosity, water absorption and bulk density determined were 31.1%, 2.3 x 10 3 kg/m 3 , 4.86 x 10 6 N/m 2 and 13.2 % for mullite; 30.2%, 2.4 x 10 3 kg/m 3 , 3.20 x 10 6 N/m 2 and W = 12.8 % for alumina; and 25.2 %, 2.1 x 10 3 kg/m 3 , 2.61 x 10 6 N/m 2 and W = 11.8% for fireclay, respectively. Bauxite, andalusite and special kaolin were identified as potential raw materials for developing alumina and mullite refractories for construction of high temperature kilns and furnaces operating at 1350 0 C. The clay and kaolin minerals could be used to produce fireclay refractories for construction of incinerators operating at maximum temperatures of about 1000 0 C. The performance of the refractories was demonstrated by producing bricks to construct kilns and incinerators for the ceramic industry and hospitals. (au)

  18. Refractory disease in antineutrophil cytoplasmic antibodies associated vasculitis

    NARCIS (Netherlands)

    Rutgers, Abraham; Kallenberg, Cornelis

    Purpose of review Induction treatment of antineutrophil cytoplasmic antibodies (ANCA) associated vasculitis (AAV) is not always successful and nonresponding patients are considered refractory. Recent findings Refractory disease should be subdefined to the treatment that was received.

  19. Bacterial Adhesion & Blocking Bacterial Adhesion

    DEFF Research Database (Denmark)

    Vejborg, Rebecca Munk

    2008-01-01

    , which influence the transition from a planktonic lifestyle to a sessile lifestyle, have been studied. Protein conditioning film formation was found to influence bacterial adhesion and subsequent biofilm formation considerable, and an aqueous extract of fish muscle tissue was shown to significantly...... tract to the microbial flocs in waste water treatment facilities. Microbial biofilms may however also cause a wide range of industrial and medical problems, and have been implicated in a wide range of persistent infectious diseases, including implantassociated microbial infections. Bacterial adhesion...... is the first committing step in biofilm formation, and has therefore been intensely scrutinized. Much however, still remains elusive. Bacterial adhesion is a highly complex process, which is influenced by a variety of factors. In this thesis, a range of physico-chemical, molecular and environmental parameters...

  20. Adhesion enhancement of biomimetic dry adhesives by nanoparticle in situ synthesis

    International Nuclear Information System (INIS)

    Díaz Téllez, J P; Harirchian-Saei, S; Li, Y; Menon, C

    2013-01-01

    A novel method to increase the adhesion strength of a gecko-inspired dry adhesive is presented. Gold nanoparticles are synthesized on the tips of the microfibrils of a polymeric dry adhesive to increase its Hamaker constant. Formation of the gold nanoparticles is qualitatively studied through a colour change in the originally transparent substance and quantitatively analysed using ultraviolet–visible spectrophotometry. A pull-off force test is employed to quantify the adhesion enhancement. Specifically, adhesion forces of samples with and without embedded gold nanoparticles are measured and compared. The experimental results indicate that an adhesion improvement of 135% can be achieved. (paper)

  1. Diagnosis and management of refractory celiac disease: a systematic review.

    Science.gov (United States)

    Labidi, Asma; Serghini, Meriem; Karoui, Sami; Boubaker, Jalel; Filali, Azza

    2013-01-01

    Refractory celiac disease is defined by persisting malabsorptive symptoms in spite of a strict gluten free diet for at least 6 to 12 months. Alternatives to gluten free diet seem to be still controversial. To describe the clinical and epidemiologic aspects of refractory celiac disease, and to identify therapeutic options in this condition. Systematic review and critical analysis of observational studies, clinical trials and case reports that focused on diagnosis and management of refractory celiac disease. Refractory celiac disease can be classified as type 1 or type 2 according to the phenotype of intraepithelial lymphocytes. Great complications such as enteropathy-associated T-cell lymphoma may occur in a subgroup of these patients mainly in refractory celiac disease type 2. Curative therapies are still lacking. Refractory celiac disease remains a diagnosis of exclusion. Its prognosis remains still dismal by the absence yet of curative therapies. However, some new treatments seem to hold promise during few cohort-studies.

  2. Modern materials based on refractory compounds

    International Nuclear Information System (INIS)

    Kosolapova, T.Ya.

    1979-01-01

    Discussed are the existing methods for synthesizing powders of binary refractory compounds and high-productivity techniques which hold promise as regards the manufacture of highly disperse and pure powders. Plasmochemical synthesis is shown to be an effective method for obtaining practically all carbides, nitrides and borides. A description is given of three main methods for obtaining single crystals of refractory compounds (TiN, TiC, ZrC, ZrB 2 , NbC) fairly perfect in structure and composition. These processes include deposition from vapour-gas phase, melting in arc plasma and crystallization from solutions in metallic melts. The advantages have been shown of the self-propagating high-temperature synthesis of refractory compounds, ensuring the manufacture of products, close in composition to stoichiometric ones simultaneously with forming of items. Mechanical, thermal, abrasive, and resistive characteristics of the above materials are presented

  3. Protein adhesives

    Science.gov (United States)

    Charles R. Frihart; Linda F. Lorenz

    2018-01-01

    Nature uses a wide variety of chemicals for providing adhesion internally (e.g., cell to cell) and externally (e.g., mussels to ships and piers). This adhesive bonding is chemically and mechanically complex, involving a variety of proteins, carbohydrates, and other compounds.Consequently,the effect of protein structures on adhesive properties is only partially...

  4. Test Program for Stirling Radioisotope Generator Hardware at NASA Glenn Research Center

    Science.gov (United States)

    Lewandowski, Edward J.; Bolotin, Gary S.; Oriti, Salvatore M.

    2015-01-01

    Stirling-based energy conversion technology has demonstrated the potential of high efficiency and low mass power systems for future space missions. This capability is beneficial, if not essential, to making certain deep space missions possible. Significant progress was made developing the Advanced Stirling Radioisotope Generator (ASRG), a 140-W radioisotope power system. A variety of flight-like hardware, including Stirling convertors, controllers, and housings, was designed and built under the ASRG flight development project. To support future Stirling-based power system development NASA has proposals that, if funded, will allow this hardware to go on test at the NASA Glenn Research Center. While future flight hardware may not be identical to the hardware developed under the ASRG flight development project, many components will likely be similar, and system architectures may have heritage to ASRG. Thus, the importance of testing the ASRG hardware to the development of future Stirling-based power systems cannot be understated. This proposed testing will include performance testing, extended operation to establish an extensive reliability database, and characterization testing to quantify subsystem and system performance and better understand system interfaces. This paper details this proposed test program for Stirling radioisotope generator hardware at NASA Glenn. It explains the rationale behind the proposed tests and how these tests will meet the stated objectives.

  5. Structure, preparation and properties of refractory compounds and systems

    International Nuclear Information System (INIS)

    Holleck, H.; Thuemmler, F.

    1977-01-01

    At the beginning of this report the possibilities of hardness optimization of refractory carbides are generally discussed. Three papers deal with TaC-basis refractories and hard metals. In particular, carbides with very low nonmetal/metal ratios and composites with hard phases formed by decomposition of tantalum carbonitrides are discussed. Another contribution reports investigations concerning the influence of the microstructure on the hardness of polycristaline mixed carbides. In a series of four papers, results are presented on the work of optimization conventional WC hard metals by introduction of a Fe,Co,Ni-binder: The influence of composition, carbon content and sintering conditions, as well as the wetting behaviour between carbides and binder metals are discussed. Phase relations in the refractory nitride and refractory nitride-binder metal systems as well as phase stabilities of ordered transition metal phases are reported in three papers, fundamental in character. Finally, the work concerning chemical analysis of refractory systems is described. (orig.) [de

  6. Radiation-curable adhesives

    International Nuclear Information System (INIS)

    Woods, J.G.

    1992-01-01

    Radiation-curable adhesives may be classified into two broad categories. In the first category, adhesive bonding occurs as a direct result of irradiation. The second category includes pressure-sensitive and hot-melt adhesives, which are composed of linear or lightly cross-linked polymers prepared by a radiation-induced polymerization reaction. This chapter is mainly concerned with radiation-curable adhesives of the first category. The various adhesive types are discussed and adhesive performance is examined, particularly in relation to the chemistry and chemical technology which underlies the individual materials. A description of a limited number of representative applications is included as is an outline of recent developments of curing and dispensing equipment. 268 refs., 14 figs., 13 tabs

  7. Ceramic Adhesive and Methods for On-Orbit Repair of Re-Entry Vehicles

    Science.gov (United States)

    Riedell, James A.; Easler, Timothy E.

    2013-01-01

    This adhesive is capable of repairing damaged leading edge components of reentry vehicles while in space, and is novel with regard to its ability to be applied in the vacuum of space, and in a microgravity environment. Once applied, the adhesive provides thermal and oxidation protection to the substrate (in this case, reinforced carbon/carbon composites, RCCs) during re-entry of a space vehicle. Although there may be many formulations for repair adhesives, at the time of this reporting, this is the first known adhesive capable of an on-orbit repair. The adhesive is an engineered ceramic material composed of a pre-ceramic polymer and refractory powders in the form of a paste or putty that can be applied to a scratched, cracked, or fractured composite surface, covering and protecting the damaged area. The adhesive is then "cured" with a heat cycle, thereby cross-linking the polymer into a hardened material and bonding it to the substrate. During the heat of reentry, the material is converted to a ceramic coating that provides thermal and oxidative stability to the repaired area, thus allowing the vehicle to pass safely from space into the upper atmosphere. Ceramic powders such as SiC, ZrB2 and Y2O3 are combined with allylhydridopolycarbosilane (AHPCS) resin, and are mixed to form a paste adhesive. The material is then applied to the damaged area by brush, spatula, trowel, or other means to fill cracks, gaps, and holes, or used to bond patches onto the damaged area. The material is then cured, in a vacuum, preferably at 250F (approximately equal to 121C) for two hours. The re-entry heating of the vehicle at temperatures in excess of 3,000F (approximately equal to 1,650C) then converts this material into a ceramic coating. This invention has demonstrated advantages in resistance to high temperatures, as was demonstrated in more than 100 arc-jet tests in representative environments at NASA. Extensive testing verified oxidation protection for the repaired substrate (RCC

  8. Switchable bio-inspired adhesives

    Science.gov (United States)

    Kroner, Elmar

    2015-03-01

    Geckos have astonishing climbing abilities. They can adhere to almost any surface and can run on walls and even stick to ceilings. The extraordinary adhesion performance is caused by a combination of a complex surface pattern on their toes and the biomechanics of its movement. These biological dry adhesives have been intensely investigated during recent years because of the unique combination of adhesive properties. They provide high adhesion, allow for easy detachment, can be removed residue-free, and have self-cleaning properties. Many aspects have been successfully mimicked, leading to artificial, bio-inspired, patterned dry adhesives, and were addressed and in some aspects they even outperform the adhesion capabilities of geckos. However, designing artificial patterned adhesion systems with switchable adhesion remains a big challenge; the gecko's adhesion system is based on a complex hierarchical surface structure and on advanced biomechanics, which are both difficult to mimic. In this paper, two approaches are presented to achieve switchable adhesion. The first approach is based on a patterned polydimethylsiloxane (PDMS) polymer, where adhesion can be switched on and off by applying a low and a high compressive preload. The switch in adhesion is caused by a reversible mechanical instability of the adhesive silicone structures. The second approach is based on a composite material consisting of a Nickel- Titanium (NiTi) shape memory alloy and a patterned adhesive PDMS layer. The NiTi alloy is trained to change its surface topography as a function of temperature, which results in a change of the contact area and of alignment of the adhesive pattern towards a substrate, leading to switchable adhesion. These examples show that the unique properties of bio-inspired adhesives can be greatly improved by new concepts such as mechanical instability or by the use of active materials which react to external stimuli.

  9. Multimillion Dollar Construction Project Completed in Glenn's Icing Research Tunnel

    Science.gov (United States)

    Kevdzija, Susan L.

    2001-01-01

    Over the last year, the Glenn Research Center's Icing Research Tunnel (IRT) underwent a major $5.2 million rehabilitation project as part of the Construction of Facilities program. The scope of the project included redesign and replacement of the 55-yr-old heat exchanger, the addition of fan outlet guide vanes for flow conditioning downstream of the 25-ft-diameter fan, and redesign and replacement of the C and D corner-turning vanes. The purpose of the rehabilitation was to replace old portions of the infrastructure and to improve the aerodynamic flow quality in the tunnel.

  10. Friction, adhesion and corrosion performance of metallurgical coatings in HTGR-helium

    International Nuclear Information System (INIS)

    Engel, R.; Kleemann, W.

    1981-01-01

    The friction-, adhesion-, thermal cycling- and corrosion performance of several metallurgical coating systems have been tested in a simulated HTGR-test atmosphere at elevated temperatures. The coatings were applied to a solid solution strengthened Ni-based superalloy. Component design requires coatings for the protection of mating surfaces, since under reactor operating conditions, contacting surfaces of metallic components under high pressures are prone to friction and wear damage. The coatings will have to protect the metal surface for 30 years up to 950 0 C in HTGR-helium. The materials tested were various refractory carbides with or without metallic binders and intermetallic compounds. The coatings evaluated were applied by plasma spraying-, detonation gun- and chemical vapor deposition techniques. These yielded two types of coatings which employ different mechanisms to improve the tribiological properties and maintain coating integrity. (Auth.)

  11. TRIM15 is a focal adhesion protein that regulates focal adhesion disassembly

    Science.gov (United States)

    Uchil, Pradeep D.; Pawliczek, Tobias; Reynolds, Tracy D.; Ding, Siyuan; Hinz, Angelika; Munro, James B.; Huang, Fang; Floyd, Robert W.; Yang, Haitao; Hamilton, William L.; Bewersdorf, Joerg; Xiong, Yong; Calderwood, David A.; Mothes, Walther

    2014-01-01

    ABSTRACT Focal adhesions are macromolecular complexes that connect the actin cytoskeleton to the extracellular matrix. Dynamic turnover of focal adhesions is crucial for cell migration. Paxillin is a multi-adaptor protein that plays an important role in regulating focal adhesion dynamics. Here, we identify TRIM15, a member of the tripartite motif protein family, as a paxillin-interacting factor and a component of focal adhesions. TRIM15 localizes to focal contacts in a myosin-II-independent manner by an interaction between its coiled-coil domain and the LD2 motif of paxillin. Unlike other focal adhesion proteins, TRIM15 is a stable focal adhesion component with restricted mobility due to its ability to form oligomers. TRIM15-depleted cells display impaired cell migration and reduced focal adhesion disassembly rates, in addition to enlarged focal adhesions. Thus, our studies demonstrate a cellular function for TRIM15 as a regulatory component of focal adhesion turnover and cell migration. PMID:25015296

  12. Refractory versus resistant hypertension: Novel distinctive phenotypes

    Science.gov (United States)

    Dudenbostel, Tanja; Siddiqui, Mohammed; Gharpure, Nitin; Calhoun, David A.

    2017-01-01

    Resistant hypertension (RHTN) is relatively common with an estimated prevalence of 10-20% of treated hypertensive patients. It is defined as blood pressure (BP) >140/90 mmHg treated with ≥3 antihypertensive medications, including a diuretic, if tolerated. Refractory hypertension is a novel phenotype of severe antihypertensive treatment failure. The proposed definition for refractory hypertension, i.e. BP >140/90 mmHg with use of ≥5 different antihypertensive medications, including a diuretic and a mineralocorticoid receptor antagonist (MRA) has been applied inconsistently. In comparison to RHTN, refractory hypertension seems to be less prevalent than RHTN. This review focuses on current knowledge about this novel phenotype compared with RHTN including definition, prevalence, mechanisms, characteristics and comorbidities, including cardiovascular risk. In patients with RHTN excess fluid retention is thought to be a common mechanism for the development of RHTN. Recently, evidence has emerged suggesting that refractory hypertension may be more of neurogenic etiology due to increased sympathetic activity as opposed to excess fluid retention. Treatment recommendations for RHTN are generally based on use and intensification of diuretic therapy, especially with the combination of a long-acting thiazide-like diuretic and an MRA. Based on findings from available studies, such an approach does not seem to be a successful strategy to control BP in patients with refractory hypertension and effective sympathetic inhibition in such patients, either with medications and/or device based approaches may be needed. PMID:29034321

  13. Forming Refractory Insulation On Copper Wire

    Science.gov (United States)

    Setlock, J.; Roberts, G.

    1995-01-01

    Alternative insulating process forms flexible coat of uncured refractory insulating material on copper wire. Coated wire formed into coil or other complex shape. Wire-coating apparatus forms "green" coat on copper wire. After wire coiled, heating converts "green" coat to refractory electrical insulator. When cured to final brittle form, insulating material withstands temperatures above melting temperature of wire. Process used to make coils for motors, solenoids, and other electrical devices to be operated at high temperatures.

  14. Proteomic dataset of the sea urchin Paracentrotus lividus adhesive organs and secreted adhesive.

    Science.gov (United States)

    Lebesgue, Nicolas; da Costa, Gonçalo; Ribeiro, Raquel Mesquita; Ribeiro-Silva, Cristina; Martins, Gabriel G; Matranga, Valeria; Scholten, Arjen; Cordeiro, Carlos; Heck, Albert J R; Santos, Romana

    2016-06-01

    Sea urchins have specialized adhesive organs called tube feet, which mediate strong but reversible adhesion. Tube feet are composed by a disc, producing adhesive and de-adhesive secretions for substratum attachment, and a stem for movement. After detachment the secreted adhesive remains bound to the substratum as a footprint. Recently, a label-free quantitative proteomic approach coupled with the latest mass-spectrometry technology was used to analyze the differential proteome of Paracentrotus lividus adhesive organ, comparing protein expression levels in the tube feet adhesive part (the disc) versus the non-adhesive part (the stem), and also to profile the proteome of the secreted adhesive (glue). This data article contains complementary figures and results related to the research article "Deciphering the molecular mechanisms underlying sea urchin reversible adhesion: a quantitative proteomics approach" (Lebesgue et al., 2016) [1]. Here we provide a dataset of 1384 non-redundant proteins, their fragmented peptides and expression levels, resultant from the analysis of the tube feet differential proteome. Of these, 163 highly over-expressed tube feet disc proteins (>3-fold), likely representing the most relevant proteins for sea urchin reversible adhesion, were further annotated in order to determine the potential functions. In addition, we provide a dataset of 611 non-redundant proteins identified in the secreted adhesive proteome, as well as their functional annotation and grouping in 5 major protein groups related with adhesive exocytosis, and microbial protection. This list was further analyzed to identify the most abundant protein groups and pinpoint putative adhesive proteins, such as Nectin, the most abundant adhesive protein in sea urchin glue. The obtained data uncover the key proteins involved in sea urchins reversible adhesion, representing a step forward to the development of new wet-effective bio-inspired adhesives.

  15. Proteomic dataset of the sea urchin Paracentrotus lividus adhesive organs and secreted adhesive

    Directory of Open Access Journals (Sweden)

    Nicolas Lebesgue

    2016-06-01

    Full Text Available Sea urchins have specialized adhesive organs called tube feet, which mediate strong but reversible adhesion. Tube feet are composed by a disc, producing adhesive and de-adhesive secretions for substratum attachment, and a stem for movement. After detachment the secreted adhesive remains bound to the substratum as a footprint. Recently, a label-free quantitative proteomic approach coupled with the latest mass-spectrometry technology was used to analyze the differential proteome of Paracentrotus lividus adhesive organ, comparing protein expression levels in the tube feet adhesive part (the disc versus the non-adhesive part (the stem, and also to profile the proteome of the secreted adhesive (glue. This data article contains complementary figures and results related to the research article “Deciphering the molecular mechanisms underlying sea urchin reversible adhesion: a quantitative proteomics approach” (Lebesgue et al., 2016 [1]. Here we provide a dataset of 1384 non-redundant proteins, their fragmented peptides and expression levels, resultant from the analysis of the tube feet differential proteome. Of these, 163 highly over-expressed tube feet disc proteins (>3-fold, likely representing the most relevant proteins for sea urchin reversible adhesion, were further annotated in order to determine the potential functions. In addition, we provide a dataset of 611 non-redundant proteins identified in the secreted adhesive proteome, as well as their functional annotation and grouping in 5 major protein groups related with adhesive exocytosis, and microbial protection. This list was further analyzed to identify the most abundant protein groups and pinpoint putative adhesive proteins, such as Nectin, the most abundant adhesive protein in sea urchin glue. The obtained data uncover the key proteins involved in sea urchins reversible adhesion, representing a step forward to the development of new wet-effective bio-inspired adhesives.

  16. High-dose chemotherapy and auto-SCT for relapsed and refractory Hodgkin's lymphoma patients refractory to first-line salvage chemotherapy but responsive to second-line salvage chemotherapy.

    Science.gov (United States)

    Rauf, Muhammad Shahzad; Maghfoor, Irfan; Elhassan, Tusneem Ahmed M; Akhtar, Saad

    2015-01-01

    Relapsed or primary refractory Hodgkin's lymphoma (HL) patients refractory to first-line salvage chemotherapy (first salvage) and unable to undergo high-dose chemotherapy (HDC) and autologous stem cell transplant (auto-SCT) have very poor outcome. Some patients are offered second-line salvage chemotherapy (second salvage), if they are responsive and may receive HDC auto-SCT. We identified 31 patients (18 males, 13 females) from 1996-2012 who received second salvage prior to auto-SCT. Median age at auto-SCT is 22 years. Patients were grouped as (1) relapsed-refractory (Rel:Ref): patients with prior complete response (CR) and on relapse found refractory to first salvage and received second salvage and (2) refractory-refractory (Ref:Ref): patients refractory to both primary treatment and first salvage and received second salvage. Median follow-up is 63 months (18-170). Disease status after second salvage prior to HDC was CR 16 %, partial response (PR) 71 % and stable disease 13 %. After HDC auto-SCT, CR:PR: progressive disease was observed in 18 (58 %): four (12 %): nine (29 %) patients, respectively. Five-year overall survival (OS) for whole group is 57 % (Rel:Ref vs. Ref:Ref, 73 % vs. 48 %, p = 0.48). Progression-free survival (PFS) for whole group is 52 % (Rel:Ref vs. Ref:Ref, 73 % vs. 40 % respectively, p = 0.11). Second-line salvage is a valid approach with no long-term side effects for those HL patients who do not respond to first-line salvage chemotherapy and they can be candidate of HDC and stem cell transplant with a high ORR, the PFS and OS in relapse-refractory and refractory-refractory group of patients.

  17. Effect of adhesive thickness on adhesively bonded T-joint

    International Nuclear Information System (INIS)

    Abdullah, A R; Afendi, Mohd; Majid, M S Abdul

    2013-01-01

    The aim of this work is to analyze the effect of adhesive thickness on tensile strength of adhesively bonded stainless steel T-joint. Specimens were made from SUS 304 Stainless Steel plate and SUS 304 Stainless Steel perforated plate. Four T-joint specimens with different adhesive thicknesses (0.5, 1.0, 1.5 and 2.0 mm) were made. Experiment result shows T-joint specimen with adhesive thickness of 1.0 mm yield highest maximum load. Identical T-joint specimen jointed by spot welding was also tested. Tensile test shows welded T-Joint had eight times higher tensile load than adhesively bonded T-joint. However, in low pressure application such as urea granulator chamber, high tensile strength is not mandatory. This work is useful for designer in fertilizer industry and others who are searching for alternative to spot welding

  18. Refractory myasthenia gravis - clinical profile, comorbidities and response to rituximab.

    Science.gov (United States)

    Sudulagunta, Sreenivasa Rao; Sepehrar, Mona; Sodalagunta, Mahesh Babu; Settikere Nataraju, Aravinda; Bangalore Raja, Shiva Kumar; Sathyanarayana, Deepak; Gummadi, Siddharth; Burra, Hemanth Kumar

    2016-01-01

    Introduction: Myasthenia gravis (MG) is an antibody mediated autoimmune neuromuscular disorder characterized by fatigable muscle weakness. A proportion of myasthenia gravis patients are classified as refractory due to non responsiveness to conventional treatment. This retrospective study was done to evaluate clinical profile, epidemiological, laboratory, and features of patients with MG and mode of management using rituximab and complications. Methods: Data of myasthenia gravis patients admitted or presented to outpatient department (previous medical records) with MG between January 2008 and January 2016 were included. A total of 512 patients fulfilled the clinical and diagnostic criteria of myasthenia gravis of which 76 patients met the diagnostic certainty for refractory myasthenia gravis and were evaluated. Results: Out of 76 refractory MG patients, 53 (69.73%) patients fulfilled all the three defined criteria. The median age of onset of the refractory MG group was 36 years with a range of 27-53 years. In our study 25 patients (32.89%) belonged to the age group of 21-30 years. Anti-MuSK antibodies were positive in 8 non-refractory MG patients (2.06%) and 36 refractory MG patients (47.36%). Mean HbA 1C was found to be 8.6±2.33. The dose of administered prednisone decreased by a mean of 59.7% ( p =3.3x10 -8 ) to 94.6% ( p =2.2x10 -14 ) after the third cycle of rituximab treatment. Conclusion: The refractory MG patients are most commonly female with an early age of onset, anti-MuSK antibodies, and thymomas. Refractory MG patients have higher prevalence and poor control (HbA 1C >8%) of diabetes mellitus and dyslipidemia probably due to increased steroid usage. Rituximab is very efficient in treatment of refractory MG with adverse effects being low.

  19. RESULTS OF OUTPATIENT PROGRAM ON EFFECTIVE THERAPY OF REFRACTORY ARTERIAL HYPERTENSION

    Directory of Open Access Journals (Sweden)

    M. M. Batyushin

    2015-12-01

    Full Text Available Aim. To increase in efficacy of antihypertensive therapy in patients with refractory arterial hypertension (HT.Material and methods. Patients with refractory HT were revealed during first month of program. The causes of refractory HT were analyzed. Combined antihypertensive therapy was prescribed to reach target level of blood pressure (BP. This therapy lasted 24 weeks and included angiotensin converting enzyme (ACE inhibitor, thiazid diuretic (indapamide and dihydropyridine calcium antagonist (nifedipine XL.Results. 200 patients with refractory HT were revealed. True refractory HT took place in 59,9% of patients and pseudo refractory HT – in 40,1% of patients. Lack of diuretics or combined antihypertensive therapy were the main reason of insufficient BP control. Proposed 3-drugs therapy resulted in reduction of systolic BP from 190 to 132 Hg mm and diastolic BP from 104 to 81 Hg mm. Target level of BP was reached in 94% patients. There were no side effects which demanded to stop therapy.Conclusion. High incidence of pseudorefractory HT (40,1% is revealed. Significant prevalence of renal disturbances especially chronic interstitial inflammatory could be responsible for refractory HT development. Use of 3-drugs therapy (ACE inhibitor, indapamide and nifedipine XL provides effective control of BP in refractory and pseudorefractory HT.

  20. RESULTS OF OUTPATIENT PROGRAM ON EFFECTIVE THERAPY OF REFRACTORY ARTERIAL HYPERTENSION

    Directory of Open Access Journals (Sweden)

    M. M. Batyushin

    2007-01-01

    Full Text Available Aim. To increase in efficacy of antihypertensive therapy in patients with refractory arterial hypertension (HT.Material and methods. Patients with refractory HT were revealed during first month of program. The causes of refractory HT were analyzed. Combined antihypertensive therapy was prescribed to reach target level of blood pressure (BP. This therapy lasted 24 weeks and included angiotensin converting enzyme (ACE inhibitor, thiazid diuretic (indapamide and dihydropyridine calcium antagonist (nifedipine XL.Results. 200 patients with refractory HT were revealed. True refractory HT took place in 59,9% of patients and pseudo refractory HT – in 40,1% of patients. Lack of diuretics or combined antihypertensive therapy were the main reason of insufficient BP control. Proposed 3-drugs therapy resulted in reduction of systolic BP from 190 to 132 Hg mm and diastolic BP from 104 to 81 Hg mm. Target level of BP was reached in 94% patients. There were no side effects which demanded to stop therapy.Conclusion. High incidence of pseudorefractory HT (40,1% is revealed. Significant prevalence of renal disturbances especially chronic interstitial inflammatory could be responsible for refractory HT development. Use of 3-drugs therapy (ACE inhibitor, indapamide and nifedipine XL provides effective control of BP in refractory and pseudorefractory HT.

  1. FJ44 Turbofan Engine Test at NASA Glenn Research Center's Aero-Acoustic Propulsion Laboratory

    Science.gov (United States)

    Lauer, Joel T.; McAllister, Joseph; Loew, Raymond A.; Sutliff, Daniel L.; Harley, Thomas C.

    2009-01-01

    A Williams International FJ44-3A 3000-lb thrust class turbofan engine was tested in the NASA Glenn Research Center s Aero-Acoustic Propulsion Laboratory. This report presents the test set-up and documents the test conditions. Farfield directivity, in-duct unsteady pressures, duct mode data, and phased-array data were taken and are reported separately.

  2. Proteomic dataset of the sea urchin Paracentrotus lividus adhesive organs and secreted adhesive

    NARCIS (Netherlands)

    Lebesgue, Nicolas; da Costa, Gonçalo; Ribeiro, Raquel Mesquita; Ribeiro-Silva, Cristina; Martins, Gabriel G; Matranga, Valeria; Scholten, Arjen; Cordeiro, Carlos; Heck, Albert J R; Santos, Romana

    Sea urchins have specialized adhesive organs called tube feet, which mediate strong but reversible adhesion. Tube feet are composed by a disc, producing adhesive and de-adhesive secretions for substratum attachment, and a stem for movement. After detachment the secreted adhesive remains bound to the

  3. Chapter 9:Wood Adhesion and Adhesives

    Science.gov (United States)

    Charles R. Frihart

    2013-01-01

    The recorded history of bonding wood dates back at least 3000 years to the Egyptians (Skeist and Miron 1990, River 1994a), and adhesive bonding goes back to early mankind (Keimel 2003). Although wood and paper bonding are the largest applications for adhesives, some of the fundamental aspects leading to good bonds are not fully understood. Better understanding of these...

  4. Bone marrow immunophenotyping by flow cytometry in refractory cytopenia of childhood

    NARCIS (Netherlands)

    A.M. Aalbers (Anna Maartje); M.M. van den Heuvel-Eibrink (Marry); I. Baumann (Irith); M.N. Dworzak (Michael); H. Hasle (Henrik); F. Locatelli (Franco); B. de Moerloose (Barbara); M. Schmugge; E. Mejstříková (Ester); M. Nováková (Michaela); M. Zecca (Marco); C.M. Zwaan (Christian Michel); J.G. te Marvelde (Jeroen); A.W. Langerak (Anton); J.J.M. van Dongen (Jacques); R. Pieters (Rob); C.M. Niemeyer (Charlotte); V.H.J. van der Velden (Vincent)

    2015-01-01

    textabstractRefractory cytopenia of childhood is the most common type of childhood myelodysplastic syndrome. Because the majority of children with refractory cytopenia have a normal karyotype and a hypocellular bone marrow, differentiating refractory cytopenia from the immune-mediated bone marrow

  5. Design and fabrication of polymer based dry adhesives inspired by the gecko adhesive system

    Science.gov (United States)

    Jin, Kejia

    There has been significant interest in developing dry adhesives mimicking the gecko adhesive system, which offers several advantages compared to conventional pressure sensitive adhesives. Specifically, gecko adhesive pads have anisotropic adhesion properties: the adhesive pads (spatulae) stick strongly when sheared in one direction but are non-adherent when sheared in the opposite direction. This anisotropy property is attributed to the complex topography of the array of fine tilted and curved columnar structures (setae) that bear the spatulae. In this thesis, easy, scalable methods, relying on conventional and unconventional techniques are presented to incorporate tilt in the fabrication of synthetic polymer-based dry adhesives mimicking the gecko adhesive system, which provide anisotropic adhesion properties. In the first part of the study, the anisotropic adhesion and friction properties of samples with various tilt angles to test the validity of a nanoscale tape-peeling model of spatular function are measured. Consistent with the Peel Zone model, samples with lower tilt angles yielded larger adhesion forces. Contact mechanics of the synthetic array were highly anisotropic, consistent with the frictional adhesion model and gecko-like. Based on the original design, a new design of gecko-like dry adhesives was developed which showed superior tribological properties and furthermore showed anisotropic adhesive properties without the need for tilt in the structures. These adhesives can be used to reversibly suspend weights from vertical surfaces (e.g., walls) and, for the first time to our knowledge, horizontal surfaces (e.g., ceilings) by simultaneously and judiciously activating anisotropic friction and adhesion forces. Furthermore, adhesion properties between artificial gecko-inspired dry adhesives and rough substrates with varying roughness are studied. The results suggest that both adhesion and friction forces on a rough substrate depends significantly on the

  6. Adhesion property of epoxidized natural rubber (ENR-based adhesives containing calcium carbonate

    Directory of Open Access Journals (Sweden)

    2008-06-01

    Full Text Available The adhesion property (i.e. viscosity, loop tack and peel strength of epoxidized natural rubber (ENR 25 and ENR 50 grade-based pressure-sensitive adhesive was studied in the presence of calcium carbonate. The range of calcium carbonate loaded was from 10 to 50 parts per hundred parts of rubber (phr. Coumarone-indene resin was used as the tackifier and its concentration was fixed at 80 phr. Toluene was chosen as the solvent throughout the investigation. The substrates (PET film/paper were coated with the adhesive using a SHEEN hand coater at a coating thickness of 60 µm. Viscosity of the adhesive was measured by a HAAKE Rotary Viscometer whereas loop tack and peel strength were determined by a Llyod Adhesion Tester operating at 30 cm/min. Results show that viscosity of ENR-based adhesives increases gradually with increase in calcium carbonate loading due to the concentration effect of the filler. However, for loop tack and peel strength, it passes through a maximum at 30 phr calcium carbonate, an observation which is attributed to the optimum wettability of adhesive on the substrate at this adhesive composition. ENR 25-based adhesive consistently exhibits higher adhesion property than ENR 50 for all calcium carbonate loadings studied.

  7. Strong composition dependence of adhesive properties of ultraviolet curing adhesives with modified acrylates

    Science.gov (United States)

    Feng, Yefeng; Li, Yandong; Wang, Fupeng; Peng, Cheng; Xu, Zhichao; Hu, Jianbing

    2018-05-01

    Ultraviolet (UV) curable adhesives have been widely researched in fields of health care and electronic components. UV curing systems with modified acrylic ester prepolymers have been frequently employed. In order to clarify composition dependence of adhesive properties of adhesives containing modified acrylates, in this work, several UV curing adhesives bearing urethane and epoxy acrylates were designed and fabricated. The effects of prepolymer, diluent, feed ratio, initiator and assistant on adhesive performances were investigated. This work might offer a facile route to gain promising high-performance UV curable adhesives with desired adhesive traits through regulating their compositions.

  8. Colectomy for refractory constipation

    DEFF Research Database (Denmark)

    Raahave, Dennis; Loud, Franck Bjørn; Christensen, Elsebeth

    2010-01-01

    OBJECTIVE: This study evaluated the type of colectomy, postoperative complications, functional results, and satisfaction in patients with constipation refractory to conservative therapy. Further, colonic transit time (CTT), faecal load (coprostasis), and colon length (redundancies) were compared ...

  9. Selected Research and Development Topics on Aerospace Communications at NASA Glenn Research Center

    Science.gov (United States)

    Miranda, Felix A.; Romanofsky, Robert R.; Nessel, James A.

    2014-01-01

    This presentation discusses some of the efforts on communications RD that have been performed or are currently underway at NASA Glenn Research Center. The primary purpose of this presentation is to outline some RD topics to serve as talking points for a Technical Interchange Meeting with the Ohio State University. The meeting is scheduled to take place at The ElectroScience Laboratory of the Ohio State University on February 24, 2014.

  10. Statistical experimental design for refractory coatings

    International Nuclear Information System (INIS)

    McKinnon, J.A.; Standard, O.C.

    2000-01-01

    The production of refractory coatings on metal casting moulds is critically dependent on the development of suitable rheological characteristics, such as viscosity and thixotropy, in the initial coating slurry. In this paper, the basic concepts of mixture design and analysis are applied to the formulation of a refractory coating, with illustration by a worked example. Experimental data of coating viscosity versus composition are fitted to a statistical model to obtain a reliable method of predicting the optimal formulation of the coating. Copyright (2000) The Australian Ceramic Society

  11. Typical corrosion of alumina refractory in aluminum reflow oven

    International Nuclear Information System (INIS)

    Baldo, Jaoa B.

    2014-01-01

    The refractory linings of furnaces for secondary melting of aluminum, are exposed to intense attack by the molten metal. This occurs, because molten aluminum has a strong reducing power over the refractory oxide components, particularly Fe 2 O 3 , SiO 2 and TiO 2 . In this work, based on X-ray diffraction and scanning electron microscopy, it is presented a post mortem study of the mechanisms that lead to a premature wear of a 80% Al2O3 chemically bonded refractory bricks, used in the metal line of an aluminum re-melting furnace. The SEM analysis demonstrated that the oxides SiO 2 and TiO 2 contained in the refractory were reduced and transformed into their metallic elements causing an intense structural spalling. (author)

  12. Adhesive properties and adhesive joints strength of graphite/epoxy composites

    Science.gov (United States)

    Rudawska, Anna; Stančeková, Dana; Cubonova, Nadezda; Vitenko, Tetiana; Müller, Miroslav; Valášek, Petr

    2017-05-01

    The article presents the results of experimental research of the adhesive joints strength of graphite/epoxy composites and the results of the surface free energy of the composite surfaces. Two types of graphite/epoxy composites with different thickness were tested which are used to aircraft structure. The single-lap adhesive joints of epoxy composites were considered. Adhesive properties were described by surface free energy. Owens-Wendt method was used to determine surface free energy. The epoxy two-component adhesive was used to preparing the adhesive joints. Zwick/Roell 100 strength device were used to determination the shear strength of adhesive joints of epoxy composites. The strength test results showed that the highest value was obtained for adhesive joints of graphite-epoxy composite of smaller material thickness (0.48 mm). Statistical analysis of the results obtained, the study showed statistically significant differences between the values of the strength of the confidence level of 0.95. The statistical analysis of the results also showed that there are no statistical significant differences in average values of surface free energy (0.95 confidence level). It was noted that in each of the results the dispersion component of surface free energy was much greater than polar component of surface free energy.

  13. Beta-blockers in cirrhosis and refractory ascites

    DEFF Research Database (Denmark)

    Kimer, Nina; Feineis, Martin; Møller, Søren

    2015-01-01

    OBJECTIVE: It is currently discussed if beta-blockers exert harmful effects and increase mortality in patients with cirrhosis and refractory ascites. In this study, we provide an overview of the available literature in this field in combination with a retrospective analysis of 61 patients...... trials (9 trials on propranolol, 1 case-control study and 4 retrospective analyses) were identified. One trial suggested an increased mortality in patients treated with beta-blockers and refractory ascites. The results of the remaining trials were inconclusive. No increase in mortality among beta-blocker......-treated patients was found in the present retrospective analysis. CONCLUSIONS: Treatment with beta-blockers may increase mortality in patients with cirrhosis and refractory ascites. However, the current evidence is sparse and high-quality studies are warranted to clarify the matter....

  14. Fire and explosion hazards of refractory compound powders

    International Nuclear Information System (INIS)

    Krivtsov, V.A.; Kostina, E.S.

    1978-01-01

    Data on fire and explosion hazards of refractory compound powders (HfC, ZrC,LaB 6 , ZrN, etc.) are presented. It is shown that refractory compounds can be fire- and exposion hazardous in various degrees. Qualitative and quantitative estimations of one of fire-hazard characteristics - smoldering temperature - are presented

  15. Bacterial endotoxin adhesion to different types of orthodontic adhesives

    Directory of Open Access Journals (Sweden)

    Priscilla Coutinho ROMUALDO

    Full Text Available Abstract Bacterial endotoxin (LPS adhesion to orthodontic brackets is a known contributing factor to inflammation of the adjacent gingival tissues. Objective The aim of this study was to assess whether LPS adheres to orthodontic adhesive systems, comparing two commercial brands. Material and Methods Forty specimens were fabricated from Transbond XT and Light Bond composite and bonding agent components (n=10/component, then contaminated by immersion in a bacterial endotoxin solution. Contaminated and non-contaminated acrylic resin samples were used as positive and negative control groups, respectively. LPS quantification was performed by the Limulus Amebocyte Lysate QCL-1000™ test. Data obtained were scored and subjected to the Chi-square test using a significance level of 5%. Results There was endotoxin adhesion to all materials (p0.05. There was no significant difference (p>0.05 among commercial brands. Affinity of endotoxin was significantly greater for the bonding agents (p=0.0025. Conclusions LPS adhered to both orthodontic adhesive systems. Regardless of the brand, the endotoxin had higher affinity for the bonding agents than for the composites. There is no previous study assessing the affinity of LPS for orthodontic adhesive systems. This study revealed that LPS adheres to orthodontic adhesive systems. Therefore, additional care is recommended to orthodontic applications of these materials.

  16. STS-95 Payload Specialist Glenn participates in a parade in Cocoa Beach

    Science.gov (United States)

    1998-01-01

    STS-95 Payload Specialist John H. Glenn Jr. waves to a dense crowd of well-wishers from the back of a silver 1999 C-5 Corvette convertible during a parade down State Road A1A in nearby Cocoa Beach. Organizers of the parade include the Cocoa Beach Area Chamber of Commerce, the Brevard County Tourist Development Council, and the cities of Cape Canaveral and Cocoa Beach. The parade is reminiscent of those held after missions during the Mercury Program.

  17. Adhesive Strength of dry Adhesive Structures Depending on the Thickness of Metal Coating

    International Nuclear Information System (INIS)

    Kim, Gyu Hye; Kwon, Da Som; Kim, Mi Jung; Kim, Su Hee; Yoon, Ji Won; An, Tea Chang; Hwang, Hui Yun

    2016-01-01

    Recently, engineering applications have started to adopt solutions inspired by nature. The peculiar adhesive properties of gecko skin are an example, as they allow the animal to move freely on vertical walls and even on ceilings. The high adhesive forces between gecko feet and walls are due to the hierarchical microscopical structure of the skin. In this study, the effect of metal coatings on the adhesive strength of synthetic, hierarchically structured, dry adhesives was investigated. Synthetic dry adhesives were fabricated using PDMS micro-molds prepared by photolithography. Metal coatings on synthetic dry adhesives were formed by plasma sputtering. Adhesive strength was measured by pure shear tests. The highest adhesion strengths were found with coatings composed of 4 nm thick layers of Indium, 8 nm thick layers of Zinc and 6 nm thick layers of Gold, respectively

  18. Adhesive Strength of dry Adhesive Structures Depending on the Thickness of Metal Coating

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Gyu Hye; Kwon, Da Som; Kim, Mi Jung; Kim, Su Hee; Yoon, Ji Won; An, Tea Chang; Hwang, Hui Yun [Andong National Univ., Andong (Korea, Republic of)

    2016-07-15

    Recently, engineering applications have started to adopt solutions inspired by nature. The peculiar adhesive properties of gecko skin are an example, as they allow the animal to move freely on vertical walls and even on ceilings. The high adhesive forces between gecko feet and walls are due to the hierarchical microscopical structure of the skin. In this study, the effect of metal coatings on the adhesive strength of synthetic, hierarchically structured, dry adhesives was investigated. Synthetic dry adhesives were fabricated using PDMS micro-molds prepared by photolithography. Metal coatings on synthetic dry adhesives were formed by plasma sputtering. Adhesive strength was measured by pure shear tests. The highest adhesion strengths were found with coatings composed of 4 nm thick layers of Indium, 8 nm thick layers of Zinc and 6 nm thick layers of Gold, respectively.

  19. Physics of adhesion

    International Nuclear Information System (INIS)

    Gerberich, W W; Cordill, M J

    2006-01-01

    Adhesion physics was relegated to the lowest echelons of academic pursuit until the advent of three seemingly disconnected events. The first, atomic force microscopy (AFM), eventually allowed fine-scale measurement of adhesive point contacts. The second, large-scale computational materials science, now permits both hierarchical studies of a few thousand atoms from first principles or of billions of atoms with less precise interatomic potentials. The third is a microelectronics industry push towards the nanoscale which has provided the driving force for requiring a better understanding of adhesion physics. In the present contribution, an attempt is made at conjoining these separate events into an updating of how theoretical and experimental approaches are providing new understanding of adhesion physics. While all material couples are briefly considered, the emphasis is on metal/semiconductor and metal/ceramic interfaces. Here, adhesion energies typically range from 1 to 100 J m -2 where the larger value is considered a practical work of adhesion. Experimental emphasis is on thin-film de-adhesion for 10 to 1000 nm thick films. For comparison, theoretical approaches from first principles quantum mechanics to embedded atom methods used in multi-scale modelling are utilized

  20. Immunomodulatory therapy in refractory/recurrent ovarian cancer.

    Science.gov (United States)

    Chen, Chao-Yu; Lai, Chyong-Huey; Yang, Lan-Yan; Tang, Yun-Hsin; Chou, Hung-Hsueh; Chang, Chee-Jen; Lin, Cheng-Tao

    2015-04-01

    To investigate the efficacy and toxicity of immunomodulatory therapy (IMT) alone or as an add-on to palliative/salvage chemotherapy in patients with refractory/recurrent epithelial ovarian cancer (EOC). We retrospectively analyzed the efficacy and toxicity of IMT in 15 patients with refractory/recurrent EOC who had previously received multiple chemotherapy regimens. The median age of the patients was 56 years (range, 41-75 years). Three patients were platinum-sensitive, two were platinum-resistant, and the remaining 10 patients were refractory to platinum-based front-line chemotherapy. IMT consisted of picibanil (OK-432) on Day 1, interleukin-2 and/or interferon-α on Day 2 administered by subcutaneous injection (every week or 2-weekly). Five patients never received metronomic oral cyclophosphamide. After IMT, three patients achieved partial remission (PR, lasting for 11 months, ≥ 12 months, and 16 months), and six patients had stable disease (SD). The disease stabilizing rate (PR+SD) was 60% (3/3 in platinum-sensitive and 6/12 in platinum-resistant/refractory patients). The absolute lymphocyte count (ALC) at 1 month after IMT was significantly higher in the PR+SD group (median 1242.0/μL) than in the progression group (median 325.0/μL) (p = 0.012). No ≥ Grade 3 toxicities were observed. The median post-IMT survival time was 12 months (range, 2-39 months). IMT alone or add-on to palliative/salvage chemotherapy for refractory/recurrent EOC achieves a substantial disease stabilizing rate without severe toxicity, which might be a potential option in selected patients. The ALC 1 month after IMT could be an early indicator to disease stabilization. Copyright © 2015. Published by Elsevier B.V.

  1. Development of the Glenn Heat-Transfer (Glenn-HT) Computer Code to Enable Time-Filtered Navier-Stokes (TFNS) Simulations and Application to Film Cooling on a Flat Plate Through Long Cooling Tubes

    Science.gov (United States)

    Ameri, Ali; Shyam, Vikram; Rigby, David; Poinsatte, Phillip; Thurman, Douglas; Steinthorsson, Erlendur

    2014-01-01

    Computational fluid dynamics (CFD) analysis using Reynolds-averaged Navier-Stokes (RANS) formulation for turbomachinery-related flows has enabled improved engine component designs. RANS methodology has limitations that are related to its inability to accurately describe the spectrum of flow phenomena encountered in engines. Examples of flows that are difficult to compute accurately with RANS include phenomena such as laminar/turbulent transition, turbulent mixing due to mixing of streams, and separated flows. Large eddy simulation (LES) can improve accuracy but at a considerably higher cost. In recent years, hybrid schemes that take advantage of both unsteady RANS and LES have been proposed. This study investigated an alternative scheme, the time-filtered Navier-Stokes (TFNS) method applied to compressible flows. The method developed by Shih and Liu was implemented in the Glenn-Heat-Transfer (Glenn-HT) code and applied to film-cooling flows. In this report the method and its implementation is briefly described. The film effectiveness results obtained for film cooling from a row of 30deg holes with a pitch of 3.0 diameters emitting air at a nominal density ratio of unity and two blowing ratios of 0.5 and 1.0 are shown. Flow features under those conditions are also described.

  2. Development of the Glenn-Heat-Transfer (Glenn-HT) Computer Code to Enable Time-Filtered Navier Stokes (TFNS) Simulations and Application to Film Cooling on a Flat Plate Through Long Cooling Tubes

    Science.gov (United States)

    Ameri, Ali A.; Shyam, Vikram; Rigby, David; Poinsatte, Phillip; Thurman, Douglas; Steinthorsson, Erlendur

    2014-01-01

    Computational fluid dynamics (CFD) analysis using Reynolds-averaged Navier-Stokes (RANS) formulation for turbomachinery-related flows has enabled improved engine component designs. RANS methodology has limitations that are related to its inability to accurately describe the spectrum of flow phenomena encountered in engines. Examples of flows that are difficult to compute accurately with RANS include phenomena such as laminar/turbulent transition, turbulent mixing due to mixing of streams, and separated flows. Large eddy simulation (LES) can improve accuracy but at a considerably higher cost. In recent years, hybrid schemes that take advantage of both unsteady RANS and LES have been proposed. This study investigated an alternative scheme, the time-filtered Navier-Stokes (TFNS) method applied to compressible flows. The method developed by Shih and Liu was implemented in the Glenn-Heat-Transfer (Glenn-HT) code and applied to film-cooling flows. In this report the method and its implementation is briefly described. The film effectiveness results obtained for film cooling from a row of 30deg holes with a pitch of 3.0 diameters emitting air at a nominal density ratio of unity and two blowing ratios of 0.5 and 1.0 are shown. Flow features under those conditions are also described.

  3. The application of vernacular Australian environmental design principles in Glenn Murcutt’s architecture

    OpenAIRE

    Lecaro, Mauricio; Lau, Benson; Rodrigues, Lucelia; Jarman, Dik

    2017-01-01

    Glenn Murcutt is recognised as one of the most influential architects of the last few decades. His design philosophy, environmental awareness and in-depth understanding of the Australian context and vernacular architecture, have made him one of the leaders of critical regionalism worldwide. His buildings not only provide shelter, but also offer comfort with lower environmental impacts through simple, yet creative design solutions. Although Murcutt’s architecture is well documented, limited ev...

  4. [Therapy-resistant and therapy-refractory arterial hypertension].

    Science.gov (United States)

    Wallbach, M; Koziolek, M J

    2018-05-02

    Therapy-resistant and therapy-refractory arterial hypertension differ in prevalence, pathogenesis, prognosis and therapy. In both cases, a structured approach is required, with the exclusion of pseudoresistance and, subsequently, secondary hypertension. Resistant hypertension has been reported to be more responsive to intensified diuretic therapy, whereas refractory hypertension is presumed to require sympathoinhibitory therapy. Once the general measures and the drug-based step-up therapy have been exhausted, interventional procedures are available.

  5. Reflections about Adhesive Systems

    OpenAIRE

    de Freitas Borges, Marciano; Diesel, Pâmela Gutheil; Corrêa, Fernanda Gomez; Bernardi, Eledana; Fernandes Montagner, Anelise; Skupien, Jovito Adiel; Susin, Alexandre Henrique

    2010-01-01

    The adhesive systems are responsible for an efficient union between teeth and resin, resulting in a longevity restoration. They are organic molecules di or multifunctional that contain reactive groups that interact with dentin and with the resin monomer of composite resin. The adhesive systems are characterized by wet adhesion, which is a result of presence of hidrophylics radicals in their compositions, to promote a better bond and the best properties of the adhesion. Adhesive systems may us...

  6. Vaginal epithelial cells regulate membrane adhesiveness to co-ordinate bacterial adhesion.

    Science.gov (United States)

    Younes, Jessica A; Klappe, Karin; Kok, Jan Willem; Busscher, Henk J; Reid, Gregor; van der Mei, Henny C

    2016-04-01

    Vaginal epithelium is colonized by different bacterial strains and species. The bacterial composition of vaginal biofilms controls the balance between health and disease. Little is known about the relative contribution of the epithelial and bacterial cell surfaces to bacterial adhesion and whether and how adhesion is regulated over cell membrane regions. Here, we show that bacterial adhesion forces with cell membrane regions not located above the nucleus are stronger than with regions above the nucleus both for vaginal pathogens and different commensal and probiotic lactobacillus strains involved in health. Importantly, adhesion force ratios over membrane regions away from and above the nucleus coincided with the ratios between numbers of adhering bacteria over both regions. Bacterial adhesion forces were dramatically decreased by depleting the epithelial cell membrane of cholesterol or sub-membrane cortical actin. Thus, epithelial cells can regulate membrane regions to which bacterial adhesion is discouraged, possibly to protect the nucleus. © 2015 John Wiley & Sons Ltd.

  7. Refractory myasthenia gravis – clinical profile, comorbidities and response to rituximab

    Science.gov (United States)

    Sudulagunta, Sreenivasa Rao; Sepehrar, Mona; Sodalagunta, Mahesh Babu; Settikere Nataraju, Aravinda; Bangalore Raja, Shiva Kumar; Sathyanarayana, Deepak; Gummadi, Siddharth; Burra, Hemanth Kumar

    2016-01-01

    Introduction: Myasthenia gravis (MG) is an antibody mediated autoimmune neuromuscular disorder characterized by fatigable muscle weakness. A proportion of myasthenia gravis patients are classified as refractory due to non responsiveness to conventional treatment. This retrospective study was done to evaluate clinical profile, epidemiological, laboratory, and features of patients with MG and mode of management using rituximab and complications. Methods: Data of myasthenia gravis patients admitted or presented to outpatient department (previous medical records) with MG between January 2008 and January 2016 were included. A total of 512 patients fulfilled the clinical and diagnostic criteria of myasthenia gravis of which 76 patients met the diagnostic certainty for refractory myasthenia gravis and were evaluated. Results: Out of 76 refractory MG patients, 53 (69.73%) patients fulfilled all the three defined criteria. The median age of onset of the refractory MG group was 36 years with a range of 27–53 years. In our study 25 patients (32.89%) belonged to the age group of 21–30 years. Anti-MuSK antibodies were positive in 8 non-refractory MG patients (2.06%) and 36 refractory MG patients (47.36%). Mean HbA1C was found to be 8.6±2.33. The dose of administered prednisone decreased by a mean of 59.7% (p=3.3x10–8) to 94.6% (p=2.2x10–14) after the third cycle of rituximab treatment. Conclusion: The refractory MG patients are most commonly female with an early age of onset, anti-MuSK antibodies, and thymomas. Refractory MG patients have higher prevalence and poor control (HbA1C >8%) of diabetes mellitus and dyslipidemia probably due to increased steroid usage. Rituximab is very efficient in treatment of refractory MG with adverse effects being low. PMID:27790079

  8. IMPROVED CORROSION RESISTANCE OF ALUMINA REFRACTORIES

    Energy Technology Data Exchange (ETDEWEB)

    John P. Hurley; Patty L. Kleven

    2001-09-30

    The initial objective of this project was to do a literature search to define the problems of refractory selection in the metals and glass industries. The problems fall into three categories: Economic--What do the major problems cost the industries financially? Operational--How do the major problems affect production efficiency and impact the environment? and Scientific--What are the chemical and physical mechanisms that cause the problems to occur? This report presents a summary of these problems. It was used to determine the areas in which the EERC can provide the most assistance through bench-scale and laboratory testing. The final objective of this project was to design and build a bench-scale high-temperature controlled atmosphere dynamic corrosion application furnace (CADCAF). The furnace will be used to evaluate refractory test samples in the presence of flowing corrodents for extended periods, to temperatures of 1600 C under controlled atmospheres. Corrodents will include molten slag, steel, and glass. This test should prove useful for the glass and steel industries when faced with the decision of choosing the best refractory for flowing corrodent conditions.

  9. Clinical and microbiological features of refractory periodontitis subjects.

    Science.gov (United States)

    Colombo, A P; Haffajee, A D; Dewhirst, F E; Paster, B J; Smith, C M; Cugini, M A; Socransky, S S

    1998-02-01

    The purpose of this investigation was to compare the clinical parameters and the site prevalence and levels of 40 subgingival species in successfully treated and refractory periodontitis subjects. 94 subjects received scaling and root planing and if needed, periodontal surgery and systemically administered tetracycline. 28 refractory subjects showed mean full mouth attachment loss and/or > 3 sites showing attachment loss > 2.5 mm within 1 year post-therapy. 66 successfully treated subjects showed mean attachment level gain and no sites with attachment loss > 2.5 mm. Baseline subgingival plaque samples were taken from the mesial aspect of each tooth and the presence and levels of 40 subgingival taxa were determined using whole genomic DNA probes and checkerboard DNA-DNA hybridization. The mean levels and % of sites colonized by each species (prevalence) was computed for each subject and differences between groups sought using the Mann-Whitney test. Most of the 40 species tested, including Actinobacillus actinomycetemcomitans, Porphyromonas gingivalis, Treponema denticola and Bacteroides forsythus, were equally or less prevalent in the refractory group. Prevotella nigrescens was significantly more prevalent in successfully treated subjects, while refractory subjects harbored a larger proportion of Streptococcus species, particularly Streptococcus constellatus. The odds of a subject being refractory was 8.6 (p or = 3.5% of the total DNA probe count. Since few microbiological differences existed between treatment outcome groups using DNA probes to known species, the predominant cultivable microbiota of 33 subgingival samples from 14 refractory subjects was examined. 85% of the 1649 isolates were identified using probes to 69 recognized subgingival species. The remaining unidentified strains were classified by analyzing 16S rRNA gene sequences. Many sequenced isolates were of taxa not considered a common part of the oral microbiota such as Acinetobacter baumanni

  10. Dry adhesives with sensing features

    International Nuclear Information System (INIS)

    Krahn, J; Menon, C

    2013-01-01

    Geckos are capable of detecting detachment of their feet. Inspired by this basic observation, a novel functional dry adhesive is proposed, which can be used to measure the instantaneous forces and torques acting on an adhesive pad. Such a novel sensing dry adhesive could potentially be used by climbing robots to quickly realize and respond appropriately to catastrophic detachment conditions. The proposed torque and force sensing dry adhesive was fabricated by mixing Carbon Black (CB) and Polydimethylsiloxane (PDMS) to form a functionalized adhesive with mushroom caps. The addition of CB to PDMS resulted in conductive PDMS which, when under compression, tension or torque, resulted in a change in the resistance across the adhesive patch terminals. The proposed design of the functionalized dry adhesive enables distinguishing an applied torque from a compressive force in a single adhesive pad. A model based on beam theory was used to predict the change in resistance across the terminals as either a torque or compressive force was applied to the adhesive patch. Under a compressive force, the sensing dry adhesive was capable of measuring compression stresses from 0.11 Pa to 20.9 kPa. The torque measured by the adhesive patch ranged from 2.6 to 10 mN m, at which point the dry adhesives became detached. The adhesive strength was 1.75 kPa under an applied preload of 1.65 kPa for an adhesive patch with an adhesive contact area of 7.07 cm 2 . (paper)

  11. Dry adhesives with sensing features

    Science.gov (United States)

    Krahn, J.; Menon, C.

    2013-08-01

    Geckos are capable of detecting detachment of their feet. Inspired by this basic observation, a novel functional dry adhesive is proposed, which can be used to measure the instantaneous forces and torques acting on an adhesive pad. Such a novel sensing dry adhesive could potentially be used by climbing robots to quickly realize and respond appropriately to catastrophic detachment conditions. The proposed torque and force sensing dry adhesive was fabricated by mixing Carbon Black (CB) and Polydimethylsiloxane (PDMS) to form a functionalized adhesive with mushroom caps. The addition of CB to PDMS resulted in conductive PDMS which, when under compression, tension or torque, resulted in a change in the resistance across the adhesive patch terminals. The proposed design of the functionalized dry adhesive enables distinguishing an applied torque from a compressive force in a single adhesive pad. A model based on beam theory was used to predict the change in resistance across the terminals as either a torque or compressive force was applied to the adhesive patch. Under a compressive force, the sensing dry adhesive was capable of measuring compression stresses from 0.11 Pa to 20.9 kPa. The torque measured by the adhesive patch ranged from 2.6 to 10 mN m, at which point the dry adhesives became detached. The adhesive strength was 1.75 kPa under an applied preload of 1.65 kPa for an adhesive patch with an adhesive contact area of 7.07 cm2.

  12. Reversible Thermoset Adhesives

    Science.gov (United States)

    Mac Murray, Benjamin C. (Inventor); Tong, Tat H. (Inventor); Hreha, Richard D. (Inventor)

    2016-01-01

    Embodiments of a reversible thermoset adhesive formed by incorporating thermally-reversible cross-linking units and a method for making the reversible thermoset adhesive are provided. One approach to formulating reversible thermoset adhesives includes incorporating dienes, such as furans, and dienophiles, such as maleimides, into a polymer network as reversible covalent cross-links using Diels Alder cross-link formation between the diene and dienophile. The chemical components may be selected based on their compatibility with adhesive chemistry as well as their ability to undergo controlled, reversible cross-linking chemistry.

  13. Defining refractory migraine: results of the RHSIS Survey of American Headache Society members.

    Science.gov (United States)

    Schulman, Elliott A; Peterlin, B Lee; Lake, Alvin E; Lipton, Richard B; Hanlon, Alexandra; Siegel, Sherry; Levin, Morris; Goadsby, Peter J; Markley, Herbert G

    2009-04-01

    To gauge consensus regarding a proposed definition for refractory migraine proposed by Refractory Headache Special Interest Section, and where its use would be most appropriate. Headache experts have long recognized that a subgroup of headache sufferers remains refractory to treatment. Although different groups have proposed criteria to define refractory migraine, the definition remains controversial. The Refractory Headache Special Interest Section of the American Headache Society developed a definition through a consensus process, assisted by a literature review and initial membership survey. A 12-item questionnaire was distributed at the American Headache Society meeting in 2007 during a platform session and at the Refractory Headache Special Interest Section symposium. The same questionnaire was subsequently sent to all American Headache Society members via e-mail. A total of 151 responses from AHS members form the basis of this report. The survey instrument was designed using Survey Monkey. Frequencies and percentages of the survey were used to describe survey responses. American Headache Society members agreed that a definition for refractory migraine is needed (91%) that it should be added to the International Classification of Headache Disorders-2 (86%), and that refractory forms of non-migraine headache disorders should be defined (87%). Responders believed a refractory migraine definition would be of greatest value in selecting patients for clinical drug trials. The current refractory migraine definition requires a diagnosis of migraine, interference with function or quality of life despite modification of lifestyle factors, and adequate trials of acute and preventive medicines with established efficacy. The proposed criteria for the refractory migraine definition require failing 2 preventive medications to meet the threshold for failure. Although 42% of respondents agreed with the working definition of refractory migraine, 43% favored increasing the

  14. The Role of Refractory Dissolved Organic Matter in Ocean Carbon Sequestration

    DEFF Research Database (Denmark)

    Jørgensen, Linda

    The ocean assimilates a large amount of atmospheric CO2 and is potentially a buffer for climate change. A fraction of the assimilated CO2 is incorporated into algal biomass and further converted into refractory dissolved organic matter (DOM). Carbon bound in refractory DOM has the potential...... studies the prokaryotic production and degradation of oceanic refractory DOM and discusses the reasons for the persistent nature of this large DOM fraction. The first two papers investigate the microbial carbon pump, i.e. prokaryotic transfor-mation of organic carbon into refractory DOM. The results show...... DOM compounds in the ocean are rare—possibly too rare to sustain viable uptake and assimilation. Hence, the dilute concentration of individual compounds is a possible explanation for the apparent refractory nature of most DOM in the ocean. Understanding the mechanisms that control the quality...

  15. Intraepithelial lymphocytes in refractory celiac disease : lost in transition

    NARCIS (Netherlands)

    Schmitz, Frederike

    2014-01-01

    Refractory coeliac disease type II (RCDII) is a severe complication of coeliac disease. Whereas celiac disease can successfully be treated by the strict avoidance of gluten, refractory celiac patients show no remission despite a gluten-free diet. The pathology of RCDII is only partially understood,

  16. 70 Years of Aeropropulsion Research at NASA Glenn Research Center

    Science.gov (United States)

    Reddy, Dhanireddy R.

    2013-01-01

    This paper presents a brief overview of air-breathing propulsion research conducted at the NASA Glenn Research Center (GRC) over the past 70 years. It includes a historical perspective of the center and its various stages of propulsion research in response to the countrys different periods of crises and growth opportunities. GRCs research and technology development covered a broad spectrum, from a short-term focus on improving the energy efficiency of aircraft engines to advancing the frontier technologies of high-speed aviation in the supersonic and hypersonic speed regimes. This paper highlights major research programs, showing their impact on industry and aircraft propulsion, and briefly discusses current research programs and future aeropropulsion technology trends in related areas

  17. Clinical Features of Refractory Ascites in Outpatients

    Directory of Open Access Journals (Sweden)

    Wanda Regina Caly

    Full Text Available OBJECTIVES: To present the clinical features and outcomes of outpatients who suffer from refractory ascites. METHODS: This prospective observational study consecutively enrolled patients with cirrhotic ascites who submitted to a clinical evaluation, a sodium restriction diet, biochemical blood tests, 24 hour urine tests and an ascitic fluid analysis. All patients received a multidisciplinary evaluation and diuretic treatment. Patients who did not respond to the diuretic treatment were controlled by therapeutic serial paracentesis, and a transjugular intrahepatic portosystemic shunt was indicated for patients who required therapeutic serial paracentesis up to twice a month. RESULTS: The most common etiology of cirrhosis in both groups was alcoholism [49 refractory (R and 11 non-refractory ascites (NR]. The majority of patients in the refractory group had Child-Pugh class B cirrhosis (p=0.034. The nutritional assessment showed protein-energy malnutrition in 81.6% of the patients in the R group and 35.5% of the patients in the NR group, while hepatic encephalopathy, hernia, spontaneous bacterial peritonitis, upper digestive hemorrhage and type 2 hepatorenal syndrome were present in 51%, 44.9%, 38.8%, 38.8% and 26.5% of the patients in the R group and 9.1%, 18.2%, 0%, 0% and 0% of the patients in the NR group, respectively (p=0.016, p=0.173, p=0.012, p=0.012, and p=0.100, respectively. Mortality occurred in 28.6% of the patients in the R group and in 9.1% of the patients in the NR group (p=0.262. CONCLUSION: Patients with refractory ascites were malnourished, suffered from hernias, had a high prevalence of complications and had a high postoperative death frequency, which was mostly due to infectious processes.

  18. An Early Glenn Operation May be Associated with the Later Occurrence of Protein-Losing Enteropathy in Fontan Patients : Association of Early Glenn and Failing Fontan.

    Science.gov (United States)

    Unseld, Bettina; Stiller, Brigitte; Borth-Bruhns, Thomas; du Bois, Florian; Kroll, Johannes; Grohmann, Jochen; Fleck, Thilo

    2017-08-01

    Protein-losing enteropathy (PLE) and plastic bronchitis (PB) are major causes of long-term mortality after Fontan operation. The objective of this study was to determine early clinical risk factors before the onset of PLE and PB. In a cohort study, 106 Fontan patients between 2005 and 2013 were examined. A median of 5.3 (1.5-8.5) years later, follow-up questionnaires were used to group the patients in a PLE or PB group (n = 14) and a non-PLE/PB group (n = 92). Prevalence of PLE was 9.4% (n = 10) and of PB 3.8% (n = 4). At follow-up, five patients (4.7%) died of PLE or PB. Median age at death was 6.2 years (IQR 10.5, 95% CI 5.3-23.4). We observed no significant group differences in gender distribution (p = 0.73), ventricular morphology (p = 0.87), surgical technique (p = 0.64), conduit fenestration (p = 0.34), age at Fontan operation (p = 0.54), and need for diuretics (p = 0.56). Hypoplastic left heart syndrome was more frequent in the PLE/PB group 50 vs. 22.8% (p = 0.03) OR 3.4 (95% CI 1.1-10.8). The modified Glenn procedure was performed at a median age of 4 months (IQR 4.0) in the PLE/PB group versus 8 months (IQR 8.0) in the non-PLE/PB group (p = 0.01). The early Glenn procedure and hypoplastic left heart syndrome may be associated with the development of PLE and PB.

  19. Six-month postoperative outcomes of intraoperative OCT-guided surgical cystotomy for refractory cystoid macular edema in diabetic eyes

    Directory of Open Access Journals (Sweden)

    Asahina Y

    2017-11-01

    Full Text Available Yuichi Asahina, Naoko Tachi, Yumi Asahina, Kayoko Yoshimura, Yoshiki Ueta, Yoshihiro Hashimoto Eye Center, Shinseikai Toyama Hospital, Imizu, Toyama, Japan Purpose: This study evaluated the outcomes of surgical cystotomy for recurrent diabetic cystoid macular edema (CME.Patients and methods: We analyzed 20 eyes with a clinical diagnosis of diabetic retinopathy and refractory CME. Release of vitreoretinal adhesion, epiretinal membrane (ERM and internal limiting membrane (ILM peeling and cystotomy guided by intraoperative optical coherence tomography (iOCT were performed in every patient. Pars plana vitrectomy was also performed in 17 patients, 11 of whom also underwent lensectomy and intraocular lens implantation. Central retinal thickness (CRT, central minimum macular thickness (CMMT, macular volume (MV and best-corrected visual acuity (BCVA were compared preoperatively and 1 and 6 months post surgery.Results: CRT, CMMT and MV significantly improved 1 and 6 months post surgery in each group (P<0.01. Significant improvements in BCVA were only observed 6 months post surgery (P<0.01. No intra- or postoperative complications were observed in all patients.Conclusion: CRT, CMMT, MV and BCVA significantly improved 6 months following surgical cystectomy. This implies that iOCT-guided cystotomy could be another treatment option for refractory CME in diabetic eyes. Keywords: diabetic retinopathy, cystoid macular edema, intraoperative OCT, cystotomy

  20. F.M. Glenn Willson: Early UCSC History and the Founding of Stevenson College

    OpenAIRE

    Willson, F.M. Glenn; Jarrell, Randall; Regional History Project, UCSC Library

    1989-01-01

    Glenn Willson addresses campus developments from January 1965, when he joined the early faculty, until his resignation in 1975, when he returned home to England. During this period he held a number of campus appointments, including the provostship at Stevenson College from 1967 to 1975, and service as the chair of the Academic Senate; as Vice-Chancellor, College and Student Affairs; and as acting chair of the Theater Arts Committee. Willson focuses on three aspects of UCSC history in...

  1. Resistant and Refractory Hypertension: Antihypertensive Treatment Resistance vs Treatment Failure

    Science.gov (United States)

    Siddiqui, Mohammed; Dudenbostel, Tanja; Calhoun, David A.

    2017-01-01

    Resistant or difficult to treat hypertension is defined as high blood pressure that remains uncontrolled with 3 or more different antihypertensive medications, including a diuretic. Recent definitions also include controlled blood pressure with use of 4 or more medications as also being resistant to treatment. Recently, refractory hypertension, an extreme phenotype of antihypertensive treatment failure has been defined as hypertension uncontrolled with use of 5 or more antihypertensive agents, including a long-acting thiazide diuretic and a mineralocorticoid receptor antagonist. Patients with resistant vs refractory hypertension share similar characteristics and comorbidities, including obesity, African American race, female sex, diabetes, coronary heart disease, chronic kidney disease, and obstructive sleep apnea. Patients with refractory vs resistant hypertension tend to be younger and are more likely to have been diagnosed with congestive heart failure. Refractory hypertension might also differ from resistant hypertension in terms of underlying cause. Preliminary evidence suggests that refractory hypertension is more likely to be neurogenic in etiology (ie, heightened sympathetic tone), vs a volume-dependent hypertension that is more characteristic of resistant hypertension in general. PMID:26514749

  2. Performance assessment of refractory samples in the Los Alamos Controlled Air Incinerator

    International Nuclear Information System (INIS)

    Hutchins, D.A.; Borduin, L.C.; Koenig, R.A.; Vavruska, J.S.; Warner, C.L.

    1986-01-01

    A refractory evaluation project was initiated in 1979 to study the performance of six selected refractory materials within the Los Alamos Controlled Air Incinerator (CAI). Determining refractory resistance to thermal shock, chemical attack, and plutonium uptake was of particular interest. The experimental refractories were subjected to a variety of waste materials, including transuranic (TRU) contaminated wastes, highly chlorinated compounds and alkaline metal salts of perchlorate, chlorate, nitrate and oxylate, over the six year period of this study. Results of this study to date indicate that the use of high alumina, and possibly specialty plastic refractories, is advisable for the lining of incinerators used for the thermal destruction of diverse chemical compounds. 12 refs., 4 tabs

  3. TANNIN ADHESIVES AS AN ALTENATIVE TO THE SYNTHETIC PHENOLIC ADHESIVES

    Directory of Open Access Journals (Sweden)

    Semra Çolak

    2003-04-01

    Full Text Available Recently, increasing attention has been paid industrially to the use of tannin formaldehyde adhesives in production of wood based panel products such as particleboard, fiber board and plywood. The researches on the use of tannin extracts as a wood adhesive started in 1950, however, they proceeded very slowly since the problems associated with the application of them. The idea which tannin extract can be used replace the oil-based phenolic adhesive was the base of several studies after the oil crisis of the 1970s. In the past, the economical aspects were important in the researches on the tannin-based adhesives. Nowadays, however, both economical and ecological factors should have taken into consideration in wood bonding.

  4. Particle adhesion and removal

    CERN Document Server

    Mittal, K L

    2015-01-01

    The book provides a comprehensive and easily accessible reference source covering all important aspects of particle adhesion and removal.  The core objective is to cover both fundamental and applied aspects of particle adhesion and removal with emphasis on recent developments.  Among the topics to be covered include: 1. Fundamentals of surface forces in particle adhesion and removal.2. Mechanisms of particle adhesion and removal.3. Experimental methods (e.g. AFM, SFA,SFM,IFM, etc.) to understand  particle-particle and particle-substrate interactions.4. Mechanics of adhesion of micro- and  n

  5. Efficacy and safety of vedolizumab as a treatment option for moderate to severe refractory ulcerative colitis in two patients after liver transplant due to primary sclerosing cholangitis

    Directory of Open Access Journals (Sweden)

    Raúl Vicente Olmedo-Martín

    Full Text Available Vedolizumab is a humanized IgG1 monoclonal antibody that selectively blocks the lymphocyte integrin α4β7 and prevents its interaction with endothelial adhesion molecules and subsequent transmigration to the gastrointestinal tract. The drug was approved in 2014 for the induction and maintenance treatment of ulcerative colitis and moderate to severe Crohn's disease that is refractory or intolerant to conventional treatment with corticoids and immunosuppressants and/or anti-TNFα drugs. However, inflammatory bowel disease has a variable behavior following liver transplant. One third of patients with ulcerative colitis associated with primary sclerosing cholangitis are expected to deteriorate despite receiving immunosuppression to prevent rejection. There is limited experience with anti-TNFα agents in patients with inflammatory bowel disease in the setting of liver transplantation and the studies to date involve a limited number of cases. The efficacy and safety data of vedolizumab in this situation are unreliable and very preliminary. We present two cases with the aim to present the efficacy and safety of vedolizumab after one year of treatment in two patients who underwent a transplant due to primary sclerosing cholangitis. One case had de novo post-transplant ulcerative colitis refractory to two anti-TNFα drugs (golimumab and infliximab. The other patient had a colostomy due to fulminant colitis and developed severe ulcerative proctitis refractory to infliximab after reconstruction with an ileorectal anastomosis.

  6. Energetics of bacterial adhesion

    International Nuclear Information System (INIS)

    Loosdrecht, M.C.M. van; Zehnder, A.J.B.

    1990-01-01

    For the description of bacterial adhesion phenomena two different physico-chemical approaches are available. The first one, based on a surface Gibbs energy balance, assumes intimate contact between the interacting surfaces. The second approach, based on colloid chemical theories (DLVO theory), allows for two types of adhesion: 1) secondary minimum adhesion, which is often weak and reversible, and 2) irreversible primary minimum adhesion. In the secondary minimum adhesion a thin water film remains present between the interacting surface. The merits of both approaches are discussed in this paper. In addition, the methods available to measure the physico-chemical surface characteristics of bacteria and the influence of adsorbing (in)organic compounds, extracellular polymers and cell surface appendages on adhesion are summarized. (author) 2 figs., 1 tab., 50 refs

  7. Morphological Evaluation of the Adhesive/Enamel interfaces of Two-step Self-etching Adhesives and Multimode One-bottle Self-etching Adhesives.

    Science.gov (United States)

    Sato, Takaaki; Takagaki, Tomohiro; Matsui, Naoko; Hamba, Hidenori; Sadr, Alireza; Nikaido, Toru; Tagami, Junji

    To evaluate the acid-base resistant zone (ABRZ) at the adhesive/enamel interface of self-etching adhesives with or without prior phosphoric acid etching. Four adhesives were used in 8 groups: Clearfil SE Bond (SEB), Optibond XTR (XTR), Scotchbond Universal Adhesive (SBU), and Clearfil BOND SE ONE (ONE) without prior phosphoric-acid etching, and each adhesive with phosphoric acid etching for 10 s (P-SEB, P-XTR, P-SBU and P-ONE, respectively). After application of self-etching adhesives on ground enamel surfaces of human teeth, a flowable composite was placed. For observation of the acid-base resistant zone (ABRZ), the bonded interface was exposed to demineralizing solution (pH 4.5) for 4.5 h, followed by 5% NaOCl with ultrasonication for 20 min. After the acid-base challenge, morphological attributes of the interface were observed using SEM. ABRZ formation was confirmed in all groups. The funnel-shaped erosion beneath the interface was present in SBU and ONE, where nearly 10 to 15 μm of enamel was dissolved. With phosphoric acid etching, the ABRZs were obviously thicker compared with no phosphoric acid etching. Enamel beneath the bonding interface was more susceptible to acid dissolution in SBU and ONE. In the case of the one-bottle self-etching adhesives and universal adhesives that intrinsically have higher pH values, enamel etching should be recommended to improve the interfacial quality.

  8. White-Coat Effect Is Uncommon in Patients With Refractory Hypertension.

    Science.gov (United States)

    Siddiqui, Mohammed; Judd, Eric K; Oparil, Suzanne; Calhoun, David A

    2017-09-01

    Refractory hypertension is a recently described phenotype of antihypertensive treatment failure defined as uncontrolled blood pressure (BP) despite the use of ≥5 different antihypertensive agents, including chlorthalidone and spironolactone. Recent studies indicate that refractory hypertension is uncommon, with a prevalence of ≈5% to 10% of patients referred to a hypertension specialty clinic for uncontrolled hypertension. The prevalence of white-coat effect, that is, uncontrolled automated office BP ≥135/85 mm Hg and controlled out-of-office BP hypertensive patients overall is ≈30% to 40%. The prevalence of white-coat effect among patients with refractory hypertension has not been previously reported. In this prospective evaluation, consecutive patients referred to the University of Alabama at Birmingham Hypertension Clinic for uncontrolled hypertension were enrolled. Refractory hypertension was defined as uncontrolled automated office BP ≥135/85 mm Hg with the use of ≥5 antihypertensive agents, including chlorthalidone and spironolactone. Automated office BP measurements were based on 6 serial readings, done automatically with the use of a BpTRU device unobserved in the clinic. Out-of-office BP measurements were done by 24-hour ambulatory BP monitor. Thirty-four patients were diagnosed with refractory hypertension, of whom 31 had adequate ambulatory BP monitor readings. White-coat effect was present in only 2 patients, or 6.5% of the 31 patients with refractory hypertension, suggesting that white-coat effect is largely absent in patients with refractory hypertension. These findings suggest that white-coat effect is not a common cause of apparent lack of BP control in patients failing maximal antihypertensive treatment. © 2017 American Heart Association, Inc.

  9. Influence of Application Time and Etching Mode of Universal Adhesives on Enamel Adhesion.

    Science.gov (United States)

    Sai, Keiichi; Takamizawa, Toshiki; Imai, Arisa; Tsujimoto, Akimasa; Ishii, Ryo; Barkmeier, Wayne W; Latta, Mark A; Miyazaki, Masashi

    2018-01-01

    To investigate the influence of application time and etching mode of universal adhesives on enamel adhesion. Five universal adhesives, Adhese Universal, Bondmer Lightless, Clearfil Universal Bond Quick, G-Premio Bond, and Scotchbond Universal, were used. Bovine incisors were prepared and divided into four groups of ten teeth each. SBS, Ra, and SFE were determined after the following procedures: 1. self-etch mode with immediate air blowing after application (IA); 2. self-etch mode with prolonged application time (PA); 3. etch-and-rinse mode with IA; 4. etch-and-rinse mode with PA. After 24-h water storage, the bonded assemblies were subjected to shear bond strength (SBS) tests. For surface roughness (Ra) and surface free energy (SFE) measurements, the adhesives were simply applied to the enamel and rinsed with acetone and water before the measurements were carried out. Significantly higher SBS and Ra values were obtained with etch-and-rinse mode than with self-etch mode regardless of the application time or type of adhesive. Although most adhesives showed decreased SFE values with increased application time in self-etch mode, SFE values in etch-and-rinse mode were dependent on the adhesive type and application time. Etching mode, application time, and type of adhesive significantly influenced the SBS, Ra, and SFE values.

  10. Friction measurements of steel on refractory bricks

    International Nuclear Information System (INIS)

    Eiselstein, L.E.

    1981-08-01

    During startup or shutdown of a pool-type LMFBR, substantial shear stresses may arise between the base of the steel reactor vessel and the refractory brick support base. The magnitude of these stresses, which result from differences in thermal expansion, can be estimated if the friction coefficient is known. This report describes experiments to determine friction coefficients between 2 1/4 Cr-1Mo steel and several refractory materials and to examine effects to contact pressure, temperature, sliding velocity, lubricants, and surface condition

  11. Characterization of refractory brick based on local raw material from Lampung Province - Indonesia

    Science.gov (United States)

    Amin, Muhammad; Suryana, Yayat I.; Isnugroho, Kusno; Aji, Bramantyo B.; Birawidha, David C.; Hendronursito, Yusup

    2018-04-01

    Refractories are non-metallic inorganic materials that are difficult to melt at high temperatures and used in high-temperature casting industries. Refractories are classified into their constituent mineral feed stocks, refractories having typical plot properties commonly called fire bricks. In the manufacture of refractory bricks that exist in the market during the use of mangrove materials derived from abroad that is from China. In this research the refractory brick materials used are quartz sand, feldspart, kaolin, bentonite, and ball clay. All materials come from local Lampung Province - Indonesia. The experiment, there are 7 kinds of experimental composition, made of plot shape with size 230 mm, 65 mm in thickness, 114 mm height mould using manual press machine with 10 tons power and burning at 1400°C for 5 hours. Refractory brick product is done by physical test in the form of porosity, specific gravity, compressive strength and XRF and SEM characteristics. The result of XRF characteristic of refractory brick composition of 1 to 5 compared to the refractory brick type SK 34 in the market and the result of composition 1 is a composition close to refractory brick composition type SK 34 namely SiO2 is 54.21 %, Al2O3 is 25.38 % and test Physical of Bulk density is 2.25 g/cm3, porosity is 18.98 % and compressive strength is 325 kg/cm2.

  12. Reflections on Centaur Upper Stage Integration by the NASA Lewis (Glenn) Research Center

    Science.gov (United States)

    Graham, Scott R.

    2015-01-01

    The NASA Glenn (then Lewis) Research Center (GRC) led several expendable launch vehicle (ELV) projects from 1963 to 1998, most notably the Centaur upper stage. These major, comprehensive projects included system management, system development, integration (both payload and stage), and launch operations. The integration role that GRC pioneered was truly unique and highly successful. Its philosophy, scope, and content were not just invaluable to the missions and vehicles it supported, but also had significant Agency-wide benefits. An overview of the NASA Lewis Research Center (now the NASA Glenn Research Center) philosophy on ELV integration is provided, focusing on Atlas/Centaur, Titan/Centaur, and Shuttle/Centaur vehicles and programs. The necessity of having a stable, highly technically competent in-house staff is discussed. Significant depth of technical penetration of contractor work is another critical component. Functioning as a cohesive team was more than a concept: GRC senior management, NASA Headquarters, contractors, payload users, and all staff worked together. The scope, content, and history of launch vehicle integration at GRC are broadly discussed. Payload integration is compared to stage development integration in terms of engineering and organization. Finally, the transition from buying launch vehicles to buying launch services is discussed, and thoughts on future possibilities of employing the successful GRC experience in integrating ELV systems like Centaur are explored.

  13. User Manual for the NASA Glenn Ice Accretion Code LEWICE: Version 2.0

    Science.gov (United States)

    Wright, William B.

    1999-01-01

    A research project is underway at NASA Glenn to produce a computer code which can accurately predict ice growth under a wide range of meteorological conditions for any aircraft surface. This report will present a description of the code inputs and outputs from version 2.0 of this code, which is called LEWICE. This version differs from previous releases due to its robustness and its ability to reproduce results accurately for different spacing and time step criteria across computing platform. It also differs in the extensive effort undertaken to compare the results against the database of ice shapes which have been generated in the NASA Glenn Icing Research Tunnel (IRT) 1. This report will only describe the features of the code related to the use of the program. The report will not describe the inner working of the code or the physical models used. This information is available in the form of several unpublished documents which will be collectively referred to as a Programmers Manual for LEWICE 2 in this report. These reports are intended as an update/replacement for all previous user manuals of LEWICE. In addition to describing the changes and improvements made for this version, information from previous manuals may be duplicated so that the user will not need to consult previous manuals to use this code.

  14. Refractory benign esophageal strictures

    Directory of Open Access Journals (Sweden)

    Gopal Goyal

    2016-01-01

    Full Text Available Refractory benign esophageal stricture (RBES is a frequently encountered problem worldwide. These strictures arise from various causes such as corrosive injury, radiation therapy, peptic origin, ablative therapy, and after surgery. Most strictures can be treated successfully with endoscopic dilatation using bougies or balloons, with only a few complications. Those patients who fail after serial dilatation with bougies or balloons will come to the category of refractory strictures. Dilatation combined with intralesional steroid injections can be considered for peptic strictures, whereas incisional therapy has been demonstrated to be effective for short anastomotic strictures. When these therapeutic options do not resolve the stenosis, stent placement should be considered. Self-bougienage can be proposed to a selected group of patients with a proximal stenosis. Most of the patients of RBES respond to above-mentioned treatment and occasional patient may require surgery as the final treatment option. This review aims to provide a comprehensive approach toward endoscopic management of RBESs based on current literature and personal experience.

  15. Illness identity in young adults with refractory epilepsy.

    Science.gov (United States)

    Luyckx, Koen; Oris, Leen; Raymaekers, Koen; Rassart, Jessica; Moons, Philip; Verdyck, Ludo; Mijnster, Teus; Mark, Ruth E

    2018-03-01

    Refractory epilepsy is an intrusive condition with important implications for daily functioning in emerging and young adulthood. The present study examined the degree to which refractory epilepsy is integrated in one's identity, and examined how such a sense of illness identity was related to health-related quality of life (HRQOL). A total of 121 18- to 40-year-old patients with refractory epilepsy (56.2% women) completed self-report questionnaires assessing the four illness identity states of acceptance, enrichment, engulfment, and rejection (Illness Identity Questionnaire (IIQ)); HRQOL (Quality of Life in Epilepsy Inventory - 31); and seizure frequency and severity (Liverpool Seizure Severity Scale (LSSS)). Illness identity scores were compared with a sample of 191 patients with a nonneurological chronic disease (congenital heart disease). Hierarchical regression analyses were conducted to assess the predictive value of illness identity for HRQOL when simultaneously controlling for demographic and clinical features. Patients with refractory epilepsy scored higher on rejection and engulfment and lower on acceptance when compared with patients with congenital heart disease. Further, seizure severity and number of medication side-effects were positively related to engulfment and negatively to acceptance. Finally, when simultaneously controlling for various demographic and clinical variables, illness identity significantly predicted HRQOL (with engulfment being the strongest and most consistent predictor). The extent to which patients with refractory epilepsy succeed in integrating their illness into their identity may have important implications for HRQOL. Clinicians should be especially attentive for signs that patients feel engulfed by their epilepsy. Copyright © 2018 Elsevier Inc. All rights reserved.

  16. Ketogenic diet treatment for pediatric super-refractory status epilepticus.

    Science.gov (United States)

    Appavu, Brian; Vanatta, Lisa; Condie, John; Kerrigan, John F; Jarrar, Randa

    2016-10-01

    We aimed to study whether ketogenic diet (KD) therapy leads to resolution of super-refractory status epilepticus in pediatric patients without significant harm. A retrospective review was performed at Phoenix Children's Hospital on patients with super-refractory status epilepticus undergoing ketogenic diet therapy from 2011 to 2015. Ten children with super-refractory status epilepticus, ages 2-16 years, were identified. 4/10 patients had immune mediated encephalitis, including Rasmussen encephalitis, anti-N-methyl-d-aspartate receptor encephalitis, and post-infectious mycoplasma encephalitis. Other etiologies included Lennox Gastaut Syndrome, non-ketotic hyperglycinemia, PCDH19 and GABRG2 genetic epilepsy, New Onset Refractory Status Epilepticus, and Febrile Infection-Related Epilepsy Syndrome. 4/10 patients' EEG features suggested focal with status epilepticus, and 6/10 suggested generalized with status epilepticus. Median hospital length was 61days and median ICU length was 27days. The median number of antiepileptic medications prior to diet initiation was 3.0 drugs, and the median after ketogenic diet treatment was 3.5 drugs. Median duration of status epilepticus prior to KD was 18days. 9/10 patients had resolution of super-refractory status epilepticus in a median of 7days after diet initiation. 8/9 patients were weaned off anesthesia within 15days of diet initiation, and within 1day of achieving ketonuria. 1/10 patients experienced side effects on the diet requiring supplementation. Most patients achieved resolution of status epilepticus on KD therapy, suggesting it could be an effective therapy that can be utilized early in the treatment of children with super refractory status epilepticus. Copyright © 2016. Published by Elsevier Ltd.

  17. Synaptic Cell Adhesion

    OpenAIRE

    Missler, Markus; Südhof, Thomas C.; Biederer, Thomas

    2012-01-01

    Chemical synapses are asymmetric intercellular junctions that mediate synaptic transmission. Synaptic junctions are organized by trans-synaptic cell adhesion molecules bridging the synaptic cleft. Synaptic cell adhesion molecules not only connect pre- and postsynaptic compartments, but also mediate trans-synaptic recognition and signaling processes that are essential for the establishment, specification, and plasticity of synapses. A growing number of synaptic cell adhesion molecules that inc...

  18. Contribuição para o diagnóstico e o tratamento das fístulas arteriovenosas pulmonares após a operação de Glenn bidirecional Contribution to the diagnosis and treatment of pulmonary arteriovenous fistulae after a bidirectional Glenn operation

    Directory of Open Access Journals (Sweden)

    Maria Virgínia Tavares Santana

    2004-12-01

    Full Text Available OBJETIVO: Determinar a incidência de fístulas arteriovenosas pulmonares (FAVPs pós-operação de Glenn bidirecional; as possíveis variáveis independentes que poderiam influenciar no seu aparecimento; comprovar o uso do ecocardiograma contrastado com microbolhas na sua detecção; e testar a sensibilidade e especificidade da angiografia pulmonar. MÉTODOS: Operados 59 pacientes, entre março 1990 e dezembro 1995, com idades entre 2 e 132 meses (média 32,7±33,6. Todos submetidos a exames clínico, laboratorial, ecocardiograma contrastado com microbolhas e cateterismo cardíaco. RESULTADOS: Nos 54 pacientes sobreviventes as FAVPs ocorreram em 20 (37,0%. A idade desses pacientes variou de 2 a 132 meses (média 29,6± 29,7. A atresia tricúspide em 10 (50,0% e o coração univentricular em 8 (40,0%, foram as cardiopatias prevalentes. Em 13 (65% a operação de Glenn bidirecional foi realizada à direita, em 2 (10,%, à esquerda e em 5 (25% foi bicaval. O tempo de seguimento dos pacientes FAVPs, variou de 4 a 84 meses (média 32,4±21,65, e nos sem fístulas de 1 a 77 meses (média de 23,4±18,8, com valor de p=0,04, com significância estatística. O diagnóstico de FAVPs foi feito pelo ecocardiograma contrastado com microbolhas nos 20 casos, sendo considerado positivo, ao se detectar retorno de microbolhas pelas veias pulmonares. A angiografia pulmonar mostrou alterações compatíveis com FAVPs em 16, demonstrando sensibilidade de 80%. CONCLUSÃO: A incidência de FAVPs pós-operação de Glenn bidirecional foi alta (37%, e o intervalo de tempo decorrido após a operação de Glenn bidirecional, foi a única variável independente que se correlacionou de forma significativa com o aparecimento das FAVPs (p=0,04; o ecocardiograma com microbolhas foi o método padrão de diagnóstico; a angiografia pulmonar se revelou um método com sensibilidade de 80,0%.OBJECTIVE: To determine the incidence of pulmonary arteriovenous fistulae (PAVFs after the

  19. Focal adhesion kinase maintains, but not increases the adhesion of dental pulp cells.

    Science.gov (United States)

    Qian, Yuyan; Shao, Meiying; Zou, Wenlin; Wang, Linyan; Cheng, Ran; Hu, Tao

    2017-04-01

    Focal adhesion kinase (FAK) functions as a key enzyme in the integrin-mediated adhesion-signalling pathway. Here, we aimed to investigate the effects of FAK on adhesion of human dental pulp (HDP) cells. We transfected lentiviral vectors to silence or overexpress FAK in HDP cells ex vivo. Early cell adhesion, cell survival and focal contacts (FCs)-related proteins (FAK and paxillin) were examined. By using immunofluorescence, the formation of FCs and cytoskeleton was detected, respectively. We found that both adhesion and survival of HDP cells were suppressed by FAK inhibition. However, FAK overexpression slightly inhibited cell adhesion and exhibited no change in cell survival compared with the control. A thick rim of cytoskeleton accumulated and smaller dot-shaped FCs appeared in FAK knockdown cells. Phosphorylation of paxillin (p-paxillin) was inhibited in FAK knockdown cells, verifying that the adhesion was inhibited. Less cytoskeleton and elongated FCs were observed in FAK-overexpressed cells. However, p-paxillin had no significant difference compared with the control. In conclusion, the data suggest that FAK maintains cell adhesion, survival and cytoskeleton formation, but excessive FAK has no positive effects on these aspects.

  20. Successes of Small Business Innovation Research at NASA Glenn Research Center

    Science.gov (United States)

    Kim, Walter S.; Bitler, Dean W.; Prok, George M.; Metzger, Marie E.; Dreibelbis, Cindy L.; Ganss, Meghan

    2002-01-01

    This booklet of success stories highlights the NASA Glenn Research Center's accomplishments and successes by the Small Business Innovation Research (SBIR) and Small Business Technology Transfer (STTR) Programs. These success stories are the results of selecting projects that support NASA missions and also have high commercialization potential. Each success story describes the innovation accomplished, commercialization of the technology, and further applications and usages. This booklet emphasizes the integration and incorporation of technologies into NASA missions and other government projects. The company name and the NASA contact person are identified to encourage further usage and application of the SBIR developed technologies and also to promote further commercialization of these products.

  1. Using H. Stephen Glenn's Developing Capable People Program with Adults in Montana: How Effective Is the Curriculum?

    Science.gov (United States)

    Astroth, Kirk A.; Lorbeer, Scott

    1998-01-01

    Pre/posttest scores of 30 participants in H. Stephen Glenn's Developing Capable People (DCP) program offered by Montana Extension showed that DCP effectively increased the use of positive behaviors and decreased negative behaviors in adults interacting with youth. These changes were sustained over 18 months after program completion. (SK)

  2. Central Diabetes Insipidus in Refractory Antineutrophil Cytoplasmic Antibody-associated Vasculitis.

    Science.gov (United States)

    Ohashi, Keiji; Morishita, Michiko; Watanabe, Haruki; Sada, Ken-Ei; Katsuyama, Takayuki; Miyawaki, Yoshia; Katsuyama, Eri; Narazaki, Mariko; Tatebe, Noriko; Watanabe, Katsue; Kawabata, Tomoko; Wada, Jun

    2017-11-01

    We herein describe two cases of refractory antineutrophil cytoplasmic antibody-associated vasculitis (AAV) complicated with diabetes insipidus (DI) possibly related to hypertrophic pachymeningitis (HP). One patient had microscopic polyangiitis and HP, which were refractory to cyclophosphamide, azathioprine, rituximab, mycophenolate mofetil (MMF), and mizoribine. Remission was finally achieved with the use of etanercept, but DI occurred 5 years later. The other patient had granulomatosis with polyangiitis, which that was refractory to cyclophosphamide, methotrexate, MMF, and rituximab. DI subsequently developed, but was successfully treated with etanercept. Dura mater hypertrophy was macroscopically observed in the latter case.

  3. A Review on Recent Advances on Magnesia-Doloma Refractories by Nano-Technology.

    Directory of Open Access Journals (Sweden)

    Salman Ghasemi-Kahrizsangi

    2017-07-01

    Full Text Available Due to exhibiting an excellent chemical resistance against basic environments at high temperature, good thermal shock resistance, thermodynamic stability in the presence of carbon, and a suitable abrasion resistance, MgO-CaO refractories are widely used in argon-oxygen decarburization furnaces in the metallurgy industry and cement rotary kilns. Furthermore, MgO-CaO refractories are beneficial to removing inclusions from molten steels; thus, they have been considered to be one of the effective refractory types for processing clean steel products. Also, MgO-CaO materials have become one of the attractive steelmaking refractories because of their low cost and high ore reserves.  However, in spite of these primary advantages, the application of MgO-CaO refractories has not been popular due to its tendency to hydration when exposed to the atmosphere.  In world most of MgO-CaO bricks producers used of organic components such as tar, pitch, and peck for produce MgO-CaO refractories. But during the application of these bricks in steel and cement and industrials, they released CO and CO2 gases to air and pollute the atmosphere. For this reason, recently some researcher investigate the effect of additive nanoparticles on MgO-CaO refractories performance. They reported the used of Nano-additive have acceptable results and additive nanoparticles can replace by aforementioned environment contaminating organic compounds. In this study, we reviewed all effort that done for improving the hydration resistance of MgO-CaO refractories by application of Nano-additives with an emphasis on the beneficial the use of additives nanoparticle for reduction of environmental pollution by various industries which used of MgO-CaO refractory bricks.

  4. Refractory Research Group - U.S. DOE, Albany Research Center [Institution Profile

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, James P.

    2004-09-01

    The refractory research group at the Albany Research Center (ARC) has a long history of conducting materials research within the U.S. Bureau of Mines, and more recently, within the U.S. Dept. of Energy. When under the U.S. Bureau of Mines, research was driven by national needs to develop substitute materials and to conserve raw materials. This mission was accomplished by improving refractory material properties and/or by recycling refractories using critical and strategic materials. Currently, as a U.S. Dept of Energy Fossil Energy field site, research is driven primarily by the need to assist DOE in meeting its vision to develop economically and environmentally viable technologies for the production of electricity from fossil fuels. Research at ARC impacts this vision by: • Providing information on the performance characteristics of materials being specified for the current generation of power systems; • Developing cost-effective, high performance materials for inclusion in the next generation of fossil power systems; and • Solving environmental emission and waste problems related to fossil energy systems. A brief history of past refractory research within the U.S. Bureau of Mines, the current refractory research at ARC, and the equipment and capabilities used to conduct refractory research at ARC will be discussed.

  5. Adhesion of multimode adhesives to enamel and dentin after one year of water storage.

    Science.gov (United States)

    Vermelho, Paulo Moreira; Reis, André Figueiredo; Ambrosano, Glaucia Maria Bovi; Giannini, Marcelo

    2017-06-01

    This study aimed to evaluate the ultramorphological characteristics of tooth-resin interfaces and the bond strength (BS) of multimode adhesive systems to enamel and dentin. Multimode adhesives (Scotchbond Universal (SBU) and All-Bond Universal) were tested in both self-etch and etch-and-rinse modes and compared to control groups (Optibond FL and Clearfil SE Bond (CSB)). Adhesives were applied to human molars and composite blocks were incrementally built up. Teeth were sectioned to obtain specimens for microtensile BS and TEM analysis. Specimens were tested after storage for either 24 h or 1 year. SEM analyses were performed to classify the failure pattern of beam specimens after BS testing. Etching increased the enamel BS of multimode adhesives; however, BS decreased after storage for 1 year. No significant differences in dentin BS were noted between multimode and control in either evaluation period. Storage for 1 year only reduced the dentin BS for SBU in self-etch mode. TEM analysis identified hybridization and interaction zones in dentin and enamel for all adhesives. Silver impregnation was detected on dentin-resin interfaces after storage of specimens for 1 year only with the SBU and CSB. Storage for 1 year reduced enamel BS when adhesives are applied on etched surface; however, BS of multimode adhesives did not differ from those of the control group. In dentin, no significant difference was noted between the multimode and control group adhesives, regardless of etching mode. In general, multimode adhesives showed similar behavior when compared to traditional adhesive techniques. Multimode adhesives are one-step self-etching adhesives that can also be used after enamel/dentin phosphoric acid etching, but each product may work better in specific conditions.

  6. Prevention of bacterial adhesion

    DEFF Research Database (Denmark)

    Klemm, Per; Vejborg, Rebecca Munk; Hancock, Viktoria

    2010-01-01

    . As such, adhesion represents the Achilles heel of crucial pathogenic functions. It follows that interference with adhesion can reduce bacterial virulence. Here, we illustrate this important topic with examples of techniques being developed that can inhibit bacterial adhesion. Some of these will become...

  7. THz Properties of Adhesives

    Science.gov (United States)

    Stübling, E.; Gomell, L.; Sommer, S.; Winkel, A.; Kahlmeyer, M.; Böhm, S.; Koch, M.

    2018-06-01

    We determined the THz properties of 12 different adhesives which are mainly used for industrial purposes. The adhesives applied can be classified according to their chemical structure: epoxy resins, acrylic resins, and polyurethane based materials. This work represents a basis for future studies, which will concentrate on aging effects, including the absorption of water of adhesive joints. Thus, the dielectric properties of the unaged adhesives are investigated and the results of these measurements are described herein.

  8. Bio-inspired reversible underwater adhesive.

    Science.gov (United States)

    Zhao, Yanhua; Wu, Yang; Wang, Liang; Zhang, Manman; Chen, Xuan; Liu, Minjie; Fan, Jun; Liu, Junqiu; Zhou, Feng; Wang, Zuankai

    2017-12-20

    The design of smart surfaces with switchable adhesive properties in a wet environment has remained a challenge in adhesion science and materials engineering. Despite intense demands in various industrial applications and exciting progress in mimicking the remarkable wet adhesion through the delicate control of catechol chemistry, polyelectrolyte complex, and supramolecular architectures, the full recapitulation of nature's dynamic function is limited. Here, we show a facile approach to synthesize bioinspired adhesive, which entails the reversible, tunable, and fast regulation of the wet adhesion on diverse surfaces. The smart wet adhesive takes advantage of the host-guest molecular interaction and the adhesive nature of catechol chemistry, as well as the responsive polymer, allowing for screening and activation of the interfacial interaction simply by a local temperature trigger in an on-demand manner. Our work opens up an avenue for the rational design of bioinspired adhesives with performances even beyond nature.

  9. Brentuximab Vedotin Treatment for Primary Refractory Hodgkin Lymphoma

    Directory of Open Access Journals (Sweden)

    Hung-Bo Wu

    2013-01-01

    Full Text Available Up to 40% of patients with advanced Hodgkin lymphoma (HL become refractory or relapsed after current standard chemotherapy, among which primary refractory HL confers a particularly poor outcome. With intensive salvage chemotherapy and autologous stem cell transplantation, the long-term remission rate for these patients was only 30%, but more selective treatments with higher therapeutic index are needed. We report the experience of using a new anti-CD30 immunotoxin, brentuximab vedotin, in salvage treatment of a 30-year-old woman with primary refractory Hodgkin lymphoma. The patient presented with SVC syndrome due to the bulky mediastinal tumor and was confirmed to have classical Hodgkin lymphoma, nodular sclerosis type, stage IIIA. The tumor responded to induction chemotherapy transiently, but local progression was noted during subsequent cycles of treatment. Salvage radiotherapy to the mediastinal tumor, obtained no remission but was followed by rapid in-field progression and then lung metastasis. She declined stem cell transplantation and received salvage brentuximab vedotin (BV therapy, which induced dramatic shrinkage of tumor without significant side effects. Serial followup of PET/CT imaging confirmed a rapid and continuous complete remission for 12 months. Although durability of the remission needs further observation, this case illustrates the excellent efficacy of brentuximab vedotin in primary refractory Hodgkin lymphoma.

  10. Long-term In Vitro Adhesion of Polyalkenoate-based Adhesives to Dentin.

    Science.gov (United States)

    Sezinando, Ana; Perdigão, Jorge; Ceballos, Laura

    2017-01-01

    To study the influence of a polyalkenoate copolymer (VCP) on the immediate (24 h) and 6-month dentin bonding stability of VCP-based adhesives, using microtensile bond strength (μTBS), nanoleakage (NL), and ultramorphological analyses (FE-SEM). Eighty-four caries-free molars were randomly assigned to seven adhesives: Clearfil SE Bond (CSE, Kuraray Noritake); Adper Single Bond Plus (SB, 3M ESPE); SB without VCP (SBnoVCP, 3M ESPE); Scotchbond Universal Adhesive applied as a etch-and-rinse adhesive (SBU_ER); SBU without VCP applied as an etch-and-rinse adhesive (SBUnoVCP_ER); SBU applied as a self-etch adhesive (SBU_SE, 3M ESPE); SBU without VCP applied as a self-etch adhesive (SBUnoVCP_SE, 3M ESPE). Half of the beams were tested after 24 h, and the other half was aged in water for 6 months prior to testing. For each tooth/evaluation time, two beams were randomly selected for NL analysis. Statistical analyses of µTBS results were performed using two-way ANOVA, Tukey's post-hoc tests, and Student's t-test for paired data (α = 0.05). Nanoleakage was statistically analyzed using the Kruskal-Wallis and Mann-Whitney tests, with Wilcoxon's test for paired data. For FE-SEM, four caries-free molars were assigned to each of the seven groups. Dentin disks were restored and cross sectioned into halves. One half was observed at 24 h, and the other at 6 months. The highest 6-month mean μTBS was obtained with SBU_SE/SBUnoVCP_SE and SBUnoVCP_ER. SBUnoVCP_SE resulted in greater silver deposition at 6 months. FE-SEM observations showed that CSE and SBU_SE specimens resulted in a submicron hybrid layer without signs of degradation at 6 months. VCP may contribute to the long-term bonding stability of VCP-based adhesives.

  11. NASA Glenn's Single-Stage Axial Compressor Facility Upgraded

    Science.gov (United States)

    Brokopp, Richard A.

    2004-01-01

    NASA Glenn Research Center's Single-Stage Axial Compressor Facility was upgraded in fiscal year 2003 to expand and improve its research capabilities for testing high-speed fans and compressors. The old 3000-hp drive motor and gearbox were removed and replaced with a refurbished 7000-hp drive motor and gearbox, with a maximum output speed of 21,240 rpm. The higher horsepower rating permits testing of fans and compressors with higher pressure ratio or higher flow. A new inline torquemeter was installed to provide an alternate measurement of fan and compressor efficiency, along with the standard pressure and temperature measurements. A refurbished compressor bearing housing was also installed with bidirectional rotation capability, so that a variety of existing hardware could be tested. Four new lubrication modules with backup capability were installed for the motor, gearbox, torquemeter, and compressor bearing housing, so that in case the primary pump fails, the backup will prevent damage to the rotating hardware. The combustion air supply line for the facility inlet air system was activated to provide dry air for repeatable inlet conditions. New flow conditioning hardware was installed in the facility inlet plenum tank, which greatly reduced the inlet turbulence. The new inlet can also be easily modified to accommodate 20- or 22-in.-diameter fans and compressors, so a variety of existing hardware from other facilities (such as Glenn's 9- by 15-Foot Low-Speed Wind Tunnel) can be tested in the Single-Stage Axial Compressor Facility. An exhaust line was also installed to provide bleed capability to remove the inlet boundary layer. To improve the operation and control of the facility, a new programmable logic controller (PLC) was installed to upgrade from hardwired relay logic to software logic. The PLC also enabled the usage of human-machine interface software to allow for easier operation of the facility and easier reconfiguration of the facility controls when

  12. Testing of the melter lid refractory for the West Valley Demonstration Project (WVDP)

    International Nuclear Information System (INIS)

    Gupta, A.; Jain, V.; Mahoney, J.L.; Holman, T.M.

    1991-01-01

    Monofrax H and Mulfrax 202 refractory were tested for potential application as the melter lid refractory for the WVDP. Resistance to spalling and corrosion by the slurry and offgas salts were primary criteria for selection. Test specimens were subjected to thermal cycling between 450 and 1,100C for five weeks. Visual examination indicated some corrosion but no spalling. SEM/EDS analysis was performed to determine the glass/refractory interface corrosion mechanism. The refractory selection basis will be discussed

  13. Bioinspired pressure actuated adhesive system

    NARCIS (Netherlands)

    Paretkar, D.R.; Kamperman, M.M.G.; Schneider, A.S.; Martina, D.; Creton, C.; Arzt, E.

    2011-01-01

    We developed a dry synthetic adhesive system inspired by gecko feet adhesion that can switch reversibly from adhesion to non-adhesion with applied pressure as external stimulus. Micropatterned polydimethylsiloxane (PDMS) surfaces with pillars of 30 µm length and 10 µm diameter were fabricated using

  14. Managing refractory Crohn's disease: challenges and solutions

    Directory of Open Access Journals (Sweden)

    Tanida S

    2015-04-01

    Full Text Available Satoshi Tanida, Keiji Ozeki, Tsutomu Mizoshita, Hironobu Tsukamoto, Takahito Katano, Hiromi Kataoka, Takeshi Kamiya, Takashi Joh Department of Gastroenterology and Metabolism, Nagoya City University Graduate School of Medical Sciences, Aichi Prefecture, Japan Abstract: The goals of treatment for active Crohn's disease (CD are to achieve clinical remission and improve quality of life. Conventional therapeutics for moderate-to-severe CD include 5-aminosalicylic acid, corticosteroids, purine analogs, azathioprine, and 6-mercaptopurine. Patients who fail to respond to conventional therapy are treated with tumor necrosis factor (TNF-α inhibitors such as infliximab and adalimumab, but their efficacy is limited due to primary nonresponse or loss of response. It is suggested that this requires switch to another TNF-α inhibitor, a combination therapy with TNF-α blockade plus azathioprine, or granulocyte and monocyte adsorptive apheresis, and that other therapeutic options having different mechanisms of action, such as blockade of inflammatory cytokines or adhesion molecules, are needed. Natalizumab and vedolizumab are neutralizing antibodies directed against integrin a4 and a4ß7, respectively. Ustekinumab is a neutralizing antibody directed against the receptors for interleukin-12 and interleukin-23. Here, we provide an overview of therapeutic treatments that are effective and currently available for CD patients, as well as some that likely will be available in the near future. We also discuss the advantages of managing patients with refractory CD using a combination of TNF-α inhibitors plus azathioprine or intensive monocyte adsorptive apheresis. Keywords: adalimumab, granulocyte and monocyte adsorptive apheresis, combination therapy, complete remission

  15. Effectiveness of botulinum toxin A in treatment of refractory erythromelalgia

    Directory of Open Access Journals (Sweden)

    Kuan-Hsiang Lin

    2013-05-01

    Full Text Available Erythromelalgia is characterized by intense burning pain, erythema, and heat in affected areas after precipitating factors such as warm temperature or stress. It is refractory to treatment in some situations. We describe a woman with adenosquamous cell carcinoma of the lung and medically refractory erythromelalgia. The symptoms of erythromelalgia presented as refractory to any medical treatment. Due to the unresponsive nature of her condition, botulinum toxin type A (onabotulinumtoxin A was injected over both of her cheeks, periodically for six cycles. Her symptoms responded dramatically to subcutaneous and intradermal injection of botulinum toxin type A. Repetitive injection demonstrated consistent and reproducible responses, and the efficacy was maintained for approximately 1 month. No adverse effects or complications were noted. Botulinum toxin type A might be safe and effective as an alternative treatment for refractory erythromelalgia, but further large-scale studies are required.

  16. Elimination of the reactivation process in the adhesion of chlorinated SBS rubber with polychloroprene adhesives

    Directory of Open Access Journals (Sweden)

    2007-04-01

    Full Text Available Chlorination treatment of a thermoplastic styrene-butadiene-styrene rubber (SBS with a 3 wt% solution of trichloroisocyanuric acid (TCI in methyl ethyl ketone (MEK introduces chlorinated and oxidized moieties on the rubber surface which increase its surface energy and produces surface microroughness. Consequently adhesion properties, evaluated by T-peel strength measurements in chlorinated SBS/solvent based-polyurethane adhesive/leather joints, are enhanced. In this study, two solvent-based polychloroprene adhesives (PCP0 and PCP30R have been considered as an alternative to the commonly used solvent-based polyurethane adhesive (PU. A thermoreactive phenolic resin was added to one of the polychloroprene adhesive formulations (PCP30R. This tackifier resin favors chlorination of the adhesive and reinforces the interface between the chlorinated adhesive and the chlorinated rubber surface. Besides, PCP30R adhesive does not need adhesive reactivation and considerable high T-peel strength value (5.7±0.3 kN/m was obtained. Elimination of the reactivation process implies a considerable improvement of the manufacturing process in the footwear industry.

  17. Theoretical and practical aspects about corrosion of refractories used in steel metallurgy: part 3: characterization of commercial refractories; Aspectos teoricos e praticos sobre a corrosao de refratarios utilizados na metalurgia: caracterizacao de refratarios comerciais

    Energy Technology Data Exchange (ETDEWEB)

    Braganca, S.R., E-mail: saulorb@ufrgs.br [Universidade Federal do Rio Grande Sul (DEMAT/UFRGS), RS (Brazil)

    2012-07-01

    In this study, it was reviewed the main aspects found in the literature about refractories corrosion, evaluating the feasibility of certain tests and relating them with experimental results. The physical properties and microstructure of commercial refractories were analyzed, considering the differences between them and the quality implications and probable life of the refractory. Thus, it was studied the various types of refractories used as lining on steel ladle. Magnesia-carbon and doloma-carbon refractories were analyzed, highlighting the differences between them. The examined refractory showed characteristics favoring high resistance to corrosion process, presenting a series of properties to be selected in accordance with industry practice. (author)

  18. Interventional embolization for refractory hyperthyroidism

    International Nuclear Information System (INIS)

    Jiang Guomin; Zhang Yunping; Chen Yaxian; Zhao Jinwei; Yang Weihuai; Chen Jinluo

    2001-01-01

    Objective: To evaluate the clinical effects of the thyroid artery embolization for refractory hyperthyroidism. Methods: Super selective catheterization and interventional embolization of thyroid superior and inferior arteries were performed with PVA microspheres and Gelfoam particles. Changes of function and size of thyroid were investigated after embolization. Results: The procedures were succeeded in all 21 patients. Followed up by 3-12 months, serum level of thyroid hormones dropped significantly (median FT 3 from 17.1 pmol/L to 7.44 pmol/L, median FT 4 from 51.1 pmol/L to 23.3 pmol/L, P< 0.01). The size of thyroid glands decreased remarkably. Symptoms of hyperthyroidism were controlled in 4 patients and were effectively controlled through low dose antithyroid medication in 17 patients. No serious complications occurred. Conclusions: Thyroid artery embolization is a new safe and effective method for refractory hyperthyroidism

  19. Efficacy of infliximab in refractory posterior uveitis in Behcet's disease patients

    OpenAIRE

    Ayman K. El Garf; Amira A. Shahin; Sherif A. Shawky; Mohammed A. Azim; Dina A. Effat; Sherry K. Abdelrahman

    2018-01-01

    Aim of the work: Ocular manifestations are the main cause of morbidity in Behcet's disease (BD). Infliximab (IFX), a chimeric monoclonal antibody directed against tumor necrosis factor-alpha, may be efficient in refractory uveitis due to BD. The aim of this study was to assess the efficacy and safety of IFX in the treatment of patients with BD-associated refractory posterior uveitis (PU). Patient and Methods: Twenty patients with refractory Behcet's PU received IFX therapy as intravenous infu...

  20. My Work in the NASA Glenn History Office and Records Management Office

    Science.gov (United States)

    Mate, Robert C.

    2004-01-01

    This is my fourth summer working with my mentor, Kevin P. Coleman, who is the Center History Coordinator, Center Records Manager, and Center Forms Manager. I am working in the GRC History Office with some overlap in the Records Management Office. I have three major projects this summer. First, I am assisting in the documentation of historic facilities. Second, I am involved in a project to organize files and create an archives at Plum Brook Station. Third, I have helped the records management office with its inventory of stored records at Plum Brook. Also, I received an award this summer for research work I had done for NASA in the past. First, my primary project is to help assemble documentation for historic facilities at Glenn. This is somewhat of an extension of my project from last summer. Last summer, I worked to compile a complete list of all of NASA s historic sites and landmarks (as designated by the National Park Service, as well as several private organizations) throughout the country. Then, I briefly researched the significance of historic designation under federal law. Finally, I put my findings into a report which was submitted to NASA Headquarters. Upon review by the NASA History Office and several center-level history officials, it was decided that NASA should work to update its documentation of its historic sites and landmarks since some of the documentation was outdated or unavailable. Until recently, many project managers and facility managers working at historic facilities were not even aware that their surroundings had been designated as historic under federal law (most specifically, the National Historic Preservation Act of 1966 and its amendments). Therefore, they were unaware of the legal obligations for historic preservation. This summer, my project is to research some of Glenn s historic sites and landmarks in more detail. The goal is to put together a template for documenting historic NASA facilities. The hope is that this template of

  1. Ketogenic diet in 3 cases of childhood refractory status epilepticus

    DEFF Research Database (Denmark)

    Sort, Rune; Born, Alfred P; Pedersen, Karen N.

    2013-01-01

    Refractory status epilepticus (RSE) in children is associated with a significant risk of death or neurological morbidity. Recently attention has been drawn to the ketogenic diet (KD) as an acute treatment, as it has shown promise in controlling seizures in otherwise refractory status epilepticus...

  2. Perspectives on environmental protection of refractory metals

    International Nuclear Information System (INIS)

    Perking, R.A.

    1992-01-01

    Alloys of refractory metals which combine high strength to weight ratios with useful low-temperature toughness and ductility have been designed to meet the requirements for the next generation of high-temperature aerospace structural materials with one exception: long term resistance to oxidation. It is considered unlikely that refractory metal alloys can be modified to possess useful resistance to oxidation as bulk materials or that coating can be designed to provide high reliability fail-safe protection for the structural alloys developed to date. Recent developments indicate that bulk alloys of W and Mo can be designed to possess short term resistance to oxidation, providing a base material which can be coated to extend useful life with fail-safe protection in the event of random coating failures. Current research on silicide coatings indicates that significant improvements in coating reliability and performance also are feasible. The technical basis for these conclusions is presented in this paper and the direction of future work that could lead to environmentally stable refractory metal alloy/coating systems is discussed

  3. Super Refractory Status Epilepticus

    African Journals Online (AJOL)

    user

    et al did retrospective cohort study from 1 January st. 1994 to 31 March 1998 at Presbyterian Medical. Centre in Columbia, to determine the frequency, risk factors and impact on the outcome of RSE. They found out that 69% of seizures recurred after. Key Words: Super refractory status epilepticus, Zambia. Medical Journal of ...

  4. Process technology - rare and refractory metals

    International Nuclear Information System (INIS)

    Gupta, C.K.; Bose, D.K.

    1989-01-01

    India has fairly rich resreves of rare and refractory metals. Abundant sources of ilmenite, rutile, zircon and rare earths are found in the placer deposits of the southern and eastern coasts of the country. Columbite-tantalite occur in mica and the mining belts of Bihar and cassiterite deposits are found in Bastar (Madhya Pradesh). Vanadium as a minor associate occurs in bauxites and in the vast deposits of titaniferrous magnetites. Over the years, research and development and pilot plant works in many research organisations in India have built up a sound technological base in the country for process metallurgy of many refractory and rare earth metals starting from their indigenous sources. The present paper provides a comprehensive view of the developments that have taken place till now on the processing of various refractory and rare earth metals with particular reference to the extensive work carried out at the Department of Atomic Energy. The coverage includes mineral benification separation of individual elements, preparation of pure intermediates, techniques of reduction to metal and final purification. The paper also reviews some of the recent developments that have been taken place in these fields and the potential application of these metals in the foreseeable future. (author). 22 refs., 18 fi g., 7 tabs

  5. Reuse of ultrafine mineral wool production waste in the manufacture of refractory concrete.

    Science.gov (United States)

    Stonys, R; Kuznetsov, D; Krasnikovs, A; Škamat, J; Baltakys, K; Antonovič, V; Černašėjus, O

    2016-07-01

    The paper deals with the mineral wool production waste (cupola dust - CD), presents CD characterization and aims to reuse CD in production of refractory concrete with calcium aluminate cement. The study of CD covers its chemical, phase and thermal analyses along with the morphological study and determination of particles size distribution. Zeta-potential, electrical conductivity and pH values of CD suspension are presented in the paper as well. Commercial microsilica additive in refractory concrete has been replaced with cupola dust. Compositions of refractory concrete have been prepared by incorporating 1%, 2% and 3% of CD. The bulk density, ultrasonic wave velocity, cold crushing strength and thermal shock resistance of the created refractory concrete have been determined. Based on experimental results, it has been found that cupola dust may be used for the production of refractory concrete. The environmental impact related to the CD reuse in refractory concrete production has been evaluated as well. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Reversible low adhesive to high adhesive superhydrophobicity transition on ZnO nanoparticle surfaces

    International Nuclear Information System (INIS)

    Li, Jian; Jing, Zhijiao; Yang, Yaoxia; Zha, Fei; Yan, Long; Lei, Ziqiang

    2014-01-01

    Superhydrophobic ZnO surfaces with water contact angle of 162° and sliding angle of 2° were fabricated successfully by spraying hydrophobic ZnO nanoparticle suspensions without limitations the shape and size of substrates. The as-prepared superhydrophobic ZnO surfaces are low adhesive and a water droplet easily rolls off with the surface slightly tilted. However, after being irradiated by UV light through a photomask, it becomes highly adhesive, on which a water droplet is firmly pinned without any movement. Further annealing the irradiated film, water droplets can roll off the surface again. Reversible transition between the low adhesive rolling state and high adhesive pinning state can be realized simply by UV illumination and heat treatment alternately. At the same time, the maximum adhesive force between the superhydrophobic ZnO surfaces and the water droplet changes from extreme low (∼5.1 μN) to very high (∼136.1 μN). When irradiated without a photomask, the surface became hydrophilic. Additionally, a water droplet can be transfered from the low adhesive superhydrophobic ZnO surfaces to the hydrophilic ZnO surfaces using the high adhesive superhydrophobic ZnO surfaces as a mechanical hand.

  7. When myasthenia gravis is deemed refractory: clinical signposts and treatment strategies

    Science.gov (United States)

    Mantegazza, Renato; Antozzi, Carlo

    2018-01-01

    The prognosis for patients with myasthenia gravis (MG) has improved significantly over the past half century, including substantial reductions in mortality and morbidity. However, approximately 10% of patients fails to respond adequately to current therapies and are considered treatment refractory, or treatment intolerant, and up to 80% have disease that fails to achieve complete stable remission. Although patients with autoantibodies to muscle-specific tyrosine kinase (anti-MuSK positive) are more likely to become treatment refractory than those with autoantibodies to the acetylcholine receptor (anti-AChR positive), each of these serotypes is substantially represented in the refractory MG population. Other risk factors for becoming treatment refractory include history of thymoma or thymectomy and female sex. A modified treatment algorithm for MG is proposed: patients who have disease that fails to respond to the stepwise approach to therapy, are treatment intolerant, or who require chronic rescue measures despite ongoing therapy, should be considered treatment refractory and emerging therapies should be considered. Three emerging monoclonal antibody-based therapies are discussed: the anti-B-cell agent rituximab; the terminal complement activation inhibitor eculizumab; and belimumab, which targets B-cell activating factor. Increased understanding of molecular pathophysiology and accurate antibody subtyping in MG should lead to the use of new therapeutic agents and successful management of treatment-refractory patients. PMID:29403543

  8. Música y medios de comunicación: en torno a Glenn Gould (1932-1982 Música y medios de comunicación: en torno a Glenn Gould (1932-1982

    Directory of Open Access Journals (Sweden)

    Michèle Dufour

    2008-04-01

    Full Text Available Glenn Gould (Toronto,1932-82 fue una de las figuras artísticas más importantes de Canadá en el siglo XX. A 25 años de su muerte se conmemora no sólo a un gran virtuoso del piano; también a un actor social relevante, que contribuyó a la redefinición de la experiencia musical culta a partir del poder de las nuevas tecnologías en la sociedad contemporánea. Su vida y obra crítica guarda una estrecha relación –implícita o explícita– con otros importantes pensadores de su tiempo, como Marshall McLuhan, Theodor W. Adorno, Max Horkheimer y Walter Benjamin. Todos ellos involucrados en reflexionar sobre el devenir de la obra de arte en la era de la reproducción industrial y de la cultura de masa.Glenn Gould (Toronto,1932-82 has been one of the most important artistic personality of Canada in the twentieth century. Twenty five years after his death, we commemorate not only a great virtuoso of the piano but also an outstanding social actor who contributed to redefine the musical experience considering the power of mass medias in the contemporary society. His life and critical writings keep a link –implicit or explicitly– with others important thinkers of his time like Marshall McLuhan, Theodor W. Adorno, Max Horkheimer and Walter Benjamin, all of them involucrate in the process of redefinition of the work of art in the industrial reproduction era and mass culture.

  9. Refractory organic substances in the environment

    National Research Council Canada - National Science Library

    Frimmel, F. H

    2002-01-01

    ... and its Quality Control in Fractions of Refractory Organic Substances and the Corresponding Original Water Samples 39 Introduction 39 Description of Analytical Methods 41 Sample Treatment 41 Fl...

  10. Evaluation of Alternative Refractory Materials for the Main Flame Deflectors at KSC Launch Complexes

    Science.gov (United States)

    Calle, Luz Marina; Trejo, David; Rutkowsky, Justin

    2006-01-01

    The deterioration of the refractory materials used to protect the KSC launch complex steel base structures from the high temperatures during launches results in frequent and costly repairs and safety hazards. KSC-SPEC-P-0012, Specification for Refractory Concrete, is ineffective in qualifying refractory materials. This study of the specification and of alternative refractory materials recommends a complete revision of the specification and further investigation of materials that were found to withstand the environment of the Solid Rocket Booster main flame deflector better than the refractory materials in current use in terms of compressive strength, tensile strength, modulus of rupture, shrinkage, and abrasion.

  11. Malleability and Machines: Glenn Gould and the Technological Self.

    Science.gov (United States)

    Jones-Imhotep, Edward

    2016-04-01

    The Pianist Glenn Gould has often been portrayed as a musical idealist who embraced mundane recording media as a way of escaping the anxiety of the concert hall. In pursuing his musical ideals, however, Gould obsessed over material objects-the qualities of a chair, the action of piano keys, the placement of splices in magnetic tape. This paper argues that for him, the detailed properties of machines and electronic media were crucial, not just as tools for pursuing disembodied aesthetic aims, but as instruments and material sites for a moral project. Locating Gould's concerns among the techniques and technologies that inspired him, the concert hall he despised, and the jazz and chance music he tolerated, the paper explores how Gould's famed philosophy of technology was rooted in a "technological self" that tied morality and aesthetics, and intimacy and isolation, to concrete ideals for the kinds of people we ought to be.

  12. Phased Array Antenna Testbed Development at the NASA Glenn Research Center

    Science.gov (United States)

    Lambert, Kevin M.; Kubat, Gregory; Johnson, Sandra K.; Anzic, Godfrey

    2003-01-01

    Ideal phased array antennas offer advantages for communication systems, such as wide-angle scanning and multibeam operation, which can be utilized in certain NASA applications. However, physically realizable, electronically steered, phased array antennas introduce additional system performance parameters, which must be included in the evaluation of the system. The NASA Glenn Research Center (GRC) is currently conducting research to identify these parameters and to develop the tools necessary to measure them. One of these tools is a testbed where phased array antennas may be operated in an environment that simulates their use. This paper describes the development of the testbed and its use in characterizing a particular K-Band, phased array antenna.

  13. PH dependent adhesive peptides

    Science.gov (United States)

    Tomich, John; Iwamoto, Takeo; Shen, Xinchun; Sun, Xiuzhi Susan

    2010-06-29

    A novel peptide adhesive motif is described that requires no receptor or cross-links to achieve maximal adhesive strength. Several peptides with different degrees of adhesive strength have been designed and synthesized using solid phase chemistries. All peptides contain a common hydrophobic core sequence flanked by positively or negatively charged amino acids sequences.

  14. User Manual for the NASA Glenn Ice Accretion Code LEWICE. Version 2.2.2

    Science.gov (United States)

    Wright, William B.

    2002-01-01

    A research project is underway at NASA Glenn to produce a computer code which can accurately predict ice growth under a wide range of meteorological conditions for any aircraft surface. This report will present a description of the code inputs and outputs from version 2.2.2 of this code, which is called LEWICE. This version differs from release 2.0 due to the addition of advanced thermal analysis capabilities for de-icing and anti-icing applications using electrothermal heaters or bleed air applications. An extensive effort was also undertaken to compare the results against the database of electrothermal results which have been generated in the NASA Glenn Icing Research Tunnel (IRT) as was performed for the validation effort for version 2.0. This report will primarily describe the features of the software related to the use of the program. Appendix A of this report has been included to list some of the inner workings of the software or the physical models used. This information is also available in the form of several unpublished documents internal to NASA. This report is intended as a replacement for all previous user manuals of LEWICE. In addition to describing the changes and improvements made for this version, information from previous manuals may be duplicated so that the user will not need to consult previous manuals to use this code.

  15. Cohesion and Adhesion with Proteins

    Science.gov (United States)

    Charles R. Frihart

    2016-01-01

    With increasing interest in bio-based adhesives, research on proteins has expanded because historically they have been used by both nature and humans as adhesives. A wide variety of proteins have been used as wood adhesives. Ancient Egyptians most likely used collagens tobond veneer to wood furniture, then came casein (milk), blood, fish scales, and soy adhesives, with...

  16. Therapeutic burst-suppression coma in pediatric febrile refractory status epilepticus.

    Science.gov (United States)

    Lin, Jainn-Jim; Chou, Cheng-Che; Lan, Shih-Yun; Hsiao, Hsiang-Ju; Wang, Yu; Chan, Oi-Wa; Hsia, Shao-Hsuan; Wang, Huei-Shyong; Lin, Kuang-Lin

    2017-09-01

    Evidence for the beneficial effect of therapeutic burst-suppression coma in pediatric patients with febrile refractory status epilepticus is limited, and the clinical outcomes of this treatment strategy are largely unknown. Therefore, the aim of this study was to explore the outcomes of therapeutic burst-suppression coma in a series of children with febrile refractory status epilepticus. We retrospectively reviewed consecutive pediatric patients with febrile refractory status epilepticus admitted to our pediatric intensive care unit between January 2000 and December 2013. The clinical characteristics were analyzed. Thirty-five patients (23 boys; age range: 1-18years) were enrolled, of whom 28 (80%) developed super-refractory status epilepticus. All of the patients received the continuous administration of intravenous antiepileptic drugs for febrile refractory status epilepticus, and 26 (74.3%) achieved therapeutic burst-suppression coma. All of the patients received mechanical ventilatory support, and 26 (74.3%) received inotropic agents. Eight (22.9%) patients died within 1month. The neurologically functional outcomes at 6months were good in six (27.3%) of the 22 survivors, of whom two returned to clinical baseline. The patients with therapeutic burst-suppression coma were significantly associated with hemodynamic support than the patients with electrographic seizures control (p=0.03), and had a trend of higher 1-month mortality rate, worse 6months outcomes, and a longer duration of hospitalization. Our results suggest that therapeutic burst-suppression coma to treat febrile refractory status epilepticus may lead to an increased risk of hemodynamic instability and a trend of worse outcomes. Copyright © 2017 The Japanese Society of Child Neurology. Published by Elsevier B.V. All rights reserved.

  17. Zirconium determination in refractories (gravimetric method)

    International Nuclear Information System (INIS)

    Capiotto, N.; Narahashi, Y.; Perish, P.G.; Souza, J.R. de

    1991-01-01

    A gravimetric method for zirconium determination in refractories is described. X-ray fluorescence analysis is also employed in this experiment and considerations about interfering elements are presented. (M.V.M.)

  18. Shape Optimization of the Assisted Bi-directional Glenn surgery for stage-1 single ventricle palliation

    Science.gov (United States)

    Verma, Aekaansh; Shang, Jessica; Esmaily-Moghadam, Mahdi; Wong, Kwai; Marsden, Alison

    2016-11-01

    Babies born with a single functional ventricle typically undergo three open-heart surgeries starting as neonates. The first of these stages (BT shunt or Norwood) has the highest mortality rates of the three, approaching 30%. Proceeding directly to a stage-2 Glenn surgery has historically demonstrated inadequate pulmonary flow (PF) & high mortality. Recently, the Assisted Bi-directional Glenn (ABG) was proposed as a promising means to achieve a stable physiology by assisting the PF via an 'ejector pump' from the systemic circulation. We present preliminary parametrization and optimization results for the ABG geometry, with the goal of increasing PF. To limit excessive pressure increases in the Superior Vena Cava (SVC), the SVC pressure is included as a constraint. We use 3-D finite element flow simulations coupled with a single ventricle lumped parameter network to evaluate PF & the pressure constraint. We employ a derivative free optimization method- the Surrogate Management Framework, in conjunction with the OpenDIEL framework to simulate multiple simultaneous evaluations. Results show that nozzle diameter is the most important design parameter affecting ABG performance. The application of these results to patient specific situations will be discussed. This work was supported by an NSF CAREER award (OCI1150184) and by the XSEDE National Computing Resource.

  19. Development of various welding techniques for refractory and reactive metals and alloys

    International Nuclear Information System (INIS)

    Tonpe, Sunil; Saibaba, N.

    2016-01-01

    Nuclear Fuel Complex (NFC), Hyderabad, India with its excellent manufacturing facilities, produces nuclear fuel and structural components for nuclear reactors. NFC has taken up the challenging job of production of various critical components made out of refractory and reactive metals and alloys for nuclear and aerospace applications as an indigenization import substitute program. Refractory metals are prime candidates for many high temperature aerospace components because of refractory metal's high melting points and inherent creep resistance. The use of refractory metals is often limited because of their poor room temperature properties, inadequate oxidation resistance at elevated temperatures, difficulties associated with joining or welding etc. These advanced materials demand stringent requirement with respect to chemistry, dimensional tolerances, mechanical and metallurgical properties. This paper discusses in detail various welding techniques adopted in NFC for refractory and reactive metals and alloys such as Nb, Zr, Ti, Ta, Zircaloy, Titanium-half alloy etc. to manufacture various components and assemblies required for nuclear and aerospace applications

  20. Applications of radioisotopes for studying refractory wear-out in Bhilai Steel Plant

    International Nuclear Information System (INIS)

    Dubey, R.S.; Bose, U.P.; Shipstone, A.J.

    1979-01-01

    In Bhilai Steel Plant, investigations were carried out to study the refractory wear-out of (i) hearth bottom of blast furnaces, (ii) roof of open hearth furnaces, and (iii) hot metal mixer lining, by using radioisotope tracer techniques with a view to evaluate the life of the refractory lining at various locations and to help in planning its timely hot and cold repairs. The life of the refractory lining has the effective bearing on the overall production and hence on the economy of the plant. The two radiometric methods employed for studying the erosion of the refractory lining, by using isotope inserted bricks at various positions without damaging the lining are (i) based on recording the penetration of gamma rays emitting from the radioactive isotopes inserted at definite points of the brick lining and, (ii) by detecting the radioactivity of the pig iron or steel arising due to washing away of the respective radioactive isotopes previously inserted in the lining. In hot mixers also radioisotope sources were placed in the critical location of refractory lining and the washing out of radioisotope due to refractory brick wear out was detected by radiogauging at site. It has been found that radiotracer technique with periodic radiogauging is very useful method for tracing the radioisotope source if more than one refractory brick with isotope is placed, as in the case of open hearth furnaces. The results of radioanalysis revealed that radioactivity coming alongwith hot metal steel has been far below the permissible limit of concentration i.e. 20 micro-curie per ton of metal. Further, during dismantling of the residual refractory lining of open hearth furnaces or hot metal mixers, bricks containing radioisotopes have been successfully retrieved for safe disposal. (auth.)

  1. Many Roles of Wood Adhesives

    Science.gov (United States)

    Charles R. Frihart

    2014-01-01

    Although wood bonding is one of the oldest applications of adhesives, going back to early recorded history (1), some aspects of wood bonds are still not fully understood. Most books in the general area of adhesives and adhesion do not cover wood bonding. However, a clearer understanding of wood bonding and wood adhesives can lead to improved products. This is important...

  2. Fragmentation process of vitrified ceramic waste (VCW) aiming its incorporation in silico-aluminous refractory concrete for production of refractory bricks

    International Nuclear Information System (INIS)

    Gomes, L.B.; Brandalise, R.N.; Santos, V. dos; Bergmann, C.P.

    2012-01-01

    Ceramic industry generates large amounts of waste, usually disposed in landfills. Reuse could minimize their generation and provides sustainable solutions. However, the energy cost of grinding these waste becomes a hindrance to their reuse. This work aims to obtain particle sizes of vitrified ceramic waste (VCW) using a fast, efficient and low cost fragmentation process as well as its use in refractory concrete. The results shows a wide range of particle size of VCW, which can be used as a promising source of raw material for production of refractory concrete. (author)

  3. Depression in patients with refractory temporal lobe epilepsy

    Directory of Open Access Journals (Sweden)

    Eleonora Borges Gonçalves

    2011-10-01

    Full Text Available OBJECTIVE: To evaluate the comorbidity of depressive disorders in patients with refractory temporal lobe epilepsy (TLE. METHOD: We evaluated 25 consecutive patients with refractory TLE (16 women and 9 men, using semi-structured psychiatric interviews, according to the International Classification of Diseases (ICD-10, and the Beck Depression Inventory. RESULTS: Seventeen of 25 patients (68% had depressive disorder: 6 with dysthymia, three with major depressive episodes and 8 with recurrent depressive disorders. Two (8% were diagnosed with mixed anxiety and depression. Only 5 of 17 patients (29.4% were previously diagnosed with depressive disorder and received prior antidepressant treatment. Duration of epilepsy was significantly higher in patients with depressive disorder (p=0.016, but there was no relationship between depression and seizure frequency. CONCLUSION: This study confirmed that depressive disorders are common and underdiagnosed in patients with TLE refractory to AEDs. Patients with longer duration of epilepsy are at higher risk of having depression.

  4. Alkali metal-refractory metal biphase electrode for AMTEC

    Science.gov (United States)

    Williams, Roger M. (Inventor); Bankston, Clyde P. (Inventor); Cole, Terry (Inventor); Khanna, Satish K. (Inventor); Jeffries-Nakamura, Barbara (Inventor); Wheeler, Bob L. (Inventor)

    1989-01-01

    An electrode having increased output with slower degradation is formed of a film applied to a beta-alumina solid electrolyte (BASE). The film comprises a refractory first metal M.sup.1 such as a platinum group metal, suitably platinum or rhodium, capable of forming a liquid or a strong surface adsorption phase with sodium at the operating temperature of an alkali metal thermoelectric converter (AMTEC) and a second refractory metal insoluble in sodium or the NaM.sup.1 liquid phase such as a Group IVB, VB or VIB metal, suitably tungsten, molybdenum, tantalum or niobium. The liquid phase or surface film provides fast transport through the electrode while the insoluble refractory metal provides a structural matrix for the electrode during operation. A trilayer structure that is stable and not subject to deadhesion comprises a first, thin layer of tungsten, an intermediate co-deposited layer of tungsten-platinum and a thin surface layer of platinum.

  5. Rheology and adhesion of poly(acrylic acid)/laponite nanocomposite hydrogels as biocompatible adhesives.

    Science.gov (United States)

    Shen, Muxian; Li, Li; Sun, Yimin; Xu, Jun; Guo, Xuhong; Prud'homme, Robert K

    2014-02-18

    Biocompatible nanocomposite hydrogels (NC gels) consisting of poly(acrylic acid) (PAA) and nanosized clay (Laponite) were successfully synthesized by in situ free-radical polymerization of acrylic acid (AA) in aqueous solutions of Laponite. The obtained NC gels were uniform and transparent. Their viscosity, storage modulus G', and loss modulus G″ increased significantly upon increasing the content of Laponite and the dose of AA, while exhibiting a maximum with increasing the neutralization degree of AA. They showed tunable adhesion by changing the dose of Laponite and monomer as well as the neutralization degree of AA, as determined by 180° peel strength measurement. The maximal adhesion was shown when reaching a balance between cohesion and fluidity. A homemade Johnson-Kendall-Roberts (JKR) instrument was employed to study the surface adhesion behavior of the NC gels. The combination of peel strength, rheology, and JKR measurements offers the opportunity of insight into the mechanism of adhesion of hydrogels. The NC gels with tunable adhesion should be ideal candidates for dental adhesive, wound dressing, and tissue engineering.

  6. NASA Glenn Steady-State Heat Pipe Code GLENHP: Compilation for 64- and 32-Bit Windows Platforms

    Science.gov (United States)

    Tower, Leonard K.; Geng, Steven M.

    2016-01-01

    A new version of the NASA Glenn Steady State Heat Pipe Code, designated "GLENHP," is introduced here. This represents an update to the disk operating system (DOS) version LERCHP reported in NASA/TM-2000-209807. The new code operates on 32- and 64-bit Windows-based platforms from within the 32-bit command prompt window. An additional evaporator boundary condition and other features are provided.

  7. Plasma deposition of refractories

    International Nuclear Information System (INIS)

    Kudinov, V.V.; Ivanov, V.M.

    1981-01-01

    The problems of deposition, testing and application of plasma coating of refractory metals and oxides are considered. The process fundamentals, various manufacturing procedures and equipment for their realization are described in detail. Coating materials are given (Al, Mg, Al 2 O 3 , ZrO 2 , MgAlO 4 ) which are used in reactor engineering and their designated purposes are shown [ru

  8. Effect of inorganic fillers in paper on the adhesion of pressure-sensitive adhesives

    Science.gov (United States)

    Weixu Chen; Xiaoyan Tang; John Considine; Kevin T. Turner

    2011-01-01

    Inorganic fillers are inexpensive materials used to increase the density, smoothness and other properties of paper that are important for printing. In the current study, the adhesion of pressure-sensitive adhesives (PSAs), a common type of adhesive used in labels and tapes, to papers containing varying amounts and types of fillers is investigated. Papers with three...

  9. Barrier Coatings for Refractory Metals and Superalloys

    Energy Technology Data Exchange (ETDEWEB)

    SM Sabol; BT Randall; JD Edington; CJ Larkin; BJ Close

    2006-02-23

    In the closed working fluid loop of the proposed Prometheus space nuclear power plant (SNPP), there is the potential for reaction of core and plant structural materials with gas phase impurities and gas phase transport of interstitial elements between superalloy and refractory metal alloy components during service. Primary concerns are surface oxidation, interstitial embrittlement of refractory metals and decarburization of superalloys. In parallel with kinetic investigations, this letter evaluates the ability of potential coatings to prevent or impede communication between reactor and plant components. Key coating requirements are identified and current technology coating materials are reviewed relative to these requirements. Candidate coatings are identified for future evaluation based on current knowledge of design parameters and anticipated environment. Coatings were identified for superalloys and refractory metals to provide diffusion barriers to interstitial transport and act as reactive barriers to potential oxidation. Due to their high stability at low oxygen potential, alumina formers are most promising for oxidation protection given the anticipated coolant gas chemistry. A sublayer of iridium is recommended to provide inherent diffusion resistance to interstitials. Based on specific base metal selection, a thin film substrate--coating interdiffusion barrier layer may be necessary to meet mission life.

  10. Barrier Coatings for Refractory Metals and Superalloys

    International Nuclear Information System (INIS)

    SM Sabol; BT Randall; JD Edington; CJ Larkin; BJ Close

    2006-01-01

    In the closed working fluid loop of the proposed Prometheus space nuclear power plant (SNPP), there is the potential for reaction of core and plant structural materials with gas phase impurities and gas phase transport of interstitial elements between superalloy and refractory metal alloy components during service. Primary concerns are surface oxidation, interstitial embrittlement of refractory metals and decarburization of superalloys. In parallel with kinetic investigations, this letter evaluates the ability of potential coatings to prevent or impede communication between reactor and plant components. Key coating requirements are identified and current technology coating materials are reviewed relative to these requirements. Candidate coatings are identified for future evaluation based on current knowledge of design parameters and anticipated environment. Coatings were identified for superalloys and refractory metals to provide diffusion barriers to interstitial transport and act as reactive barriers to potential oxidation. Due to their high stability at low oxygen potential, alumina formers are most promising for oxidation protection given the anticipated coolant gas chemistry. A sublayer of iridium is recommended to provide inherent diffusion resistance to interstitials. Based on specific base metal selection, a thin film substrate--coating interdiffusion barrier layer may be necessary to meet mission life

  11. Measuring Rock-Fluid Adhesion Directly

    Science.gov (United States)

    Tadmor, R.

    2017-12-01

    We show how to measure directly solid-liquid adhesion. We consider the normal adhesion, the work adhesion, and the lateral adhesion. The technique at the center of the method is Centrifugal Adhesion Balance (CAB) which allows coordinated manipulation of normal and lateral forces. For example: 1. It allows to induce an increase in the normal force which pulls on a liquid drop while keeping zero lateral force. This method mimics a drop that is subjected to a gravitational force that is gradually increasing. 2. It allows to increase the lateral force at zero normal force, mimicking zero gravity. From this one can obtain additional solid-liquid interaction parameters. When performing work of adhesion measurements, the values obtained are independent of drop size and are in agreement with theoretical predictions.

  12. Comparison of enamel bond fatigue durability of universal adhesives and two-step self-etch adhesives in self-etch mode.

    Science.gov (United States)

    Tsujimoto, Akimasa; Barkmeier, Wayne W; Hosoya, Yumiko; Nojiri, Kie; Nagura, Yuko; Takamizawa, Toshiki; Latta, Mark A; Miyazaki, Masashi

    2017-10-01

    To comparatively evaluate universal adhesives and two-step self-etch adhesives for enamel bond fatigue durability in self-etch mode. Three universal adhesives (Clearfil Universal Bond; G-Premio Bond; Scotchbond Universal Adhesive) and three two-step self-etch adhesives (Clearfil SE Bond; Clearfil SE Bond 2; OptiBond XTR) were used. The initial shear bond strength and shear fatigue strength of the adhesive to enamel in self-etch mode were determined. The initial shear bond strengths of the universal adhesives to enamel in self-etch mode was significantly lower than those of two-step self-etch adhesives and initial shear bond strengths were not influenced by type of adhesive in each adhesive category. The shear fatigue strengths of universal adhesives to enamel in self-etch mode were significantly lower than that of Clearfil SE Bond and Clearfil SE Bond 2, but similar to that OptiBond XTR. Unlike two-step self-etch adhesives, the initial shear bond strength and shear fatigue strength of universal adhesives to enamel in self-etch mode was not influenced by the type of adhesive. This laboratory study showed that the enamel bond fatigue durability of universal adhesives was lower than Clearfil SE Bond and Clearfil SE Bond 2, similar to Optibond XTR, and was not influenced by type of adhesive, unlike two-step self-etch adhesives.

  13. Prognostic Factors for Refractory Status Epilepticus

    Directory of Open Access Journals (Sweden)

    J. Gordon Millichap

    2013-03-01

    Full Text Available Researchers at the Mayo Clinic, Rochester, MN studied the outcome and identified prognostic factors for refractory status epilepticus (RSE in 54 adult patients, median age 52 years [range 18-93].

  14. Refractory disease in autoimmune diseases

    NARCIS (Netherlands)

    Vasconcelos, Carlos; Kallenberg, Cees; Shoenfeld, Yehuda

    Refractory disease (RD) definition has different meanings but it is dynamic, according to knowledge and the availability of new drugs. It should be differentiated from severe disease and damage definitions and it must take into account duration of adequate therapy and compliance of the patient. It

  15. Chemical analysis of refractories by plasma spectrometry

    International Nuclear Information System (INIS)

    Coutinho, C.A.

    1990-01-01

    X-ray spectrometry has been, since the last two or three decades, the traditional procedure for the chemical analysis of refractories, due to its high degree of accuracy and speed to produce analytical results. An interesting alternative to X-ray fluorescence is provided by the Inductively Coupled Plasma Spectrometry technique, for those laboratories where wet chemistry facilities are already available or process control is not required at high speed, or investiment costs have to be low. This paper presents results obtained by plasma spectroscopy for the analysis of silico - aluminous refractories, showing calibration curves, precion and detection limits. Considerations and comparisons with X-ray fluorescence are also made. (author) [pt

  16. Improvements in or relating to refractory materials

    International Nuclear Information System (INIS)

    Peckett, J.W.A.

    1980-01-01

    A process is described for the production of a refractory material which includes heating an intermediate material containing carbon to cause a thermally induced reaction involving carbon in the intermediate material, wherein the intermediate material has been produced by heating a shaped gel precipitated gel, and the carbon in the intermediate material for participating in the thermally induced reaction has been produced from a gelling agent, or a derivative thereof, incorporated in the gel during gel precipitation. As examples, the refractory material may comprise uranium/plutonium oxide, or uranium/plutonium carbide, or thorium/uranium carbide, or tungsten carbide, or tungsten carbide/cobalt metal. (author)

  17. Gastrin-releasing peptide induces monocyte adhesion to vascular endothelium by upregulating endothelial adhesion molecules

    International Nuclear Information System (INIS)

    Kim, Mi-Kyoung; Park, Hyun-Joo; Kim, Yeon; Kim, Hyung Joon; Bae, Soo-Kyung; Bae, Moon-Kyoung

    2017-01-01

    Gastrin-releasing peptide (GRP) is a neuropeptide that plays roles in various pathophysiological conditions including inflammatory diseases in peripheral tissues; however, little is known about whether GRP can directly regulate endothelial inflammatory processes. In this study, we showed that GRP promotes the adhesion of leukocytes to human umbilical vein endothelial cells (HUVECs) and the aortic endothelium. GRP increased the expression of intercellular adhesion molecule-1 (ICAM-1) and vascular cell adhesion molecule-1 (VCAM-1) by activating nuclear factor-κB (NF-κB) in endothelial cells. In addition, GRP activated extracellular signal-regulated kinase 1/2 (ERK1/2), p38MAPK, and AKT, and the inhibition of these signaling pathways significantly reduced GRP-induced monocyte adhesion to the endothelium. Overall, our results suggested that GRP may cause endothelial dysfunction, which could be of particular relevance in the development of vascular inflammatory disorders. - Highlights: • GRP induces adhesion of monocytes to vascular endothelium. • GRP increases the expression of endothelial adhesion molecules through the activation of NF-κB. • ERK1/2, p38MAPK, and Akt pathways are involved in the GRP-induced leukocyte adhesiveness to endothelium.

  18. Development of electro fused aggregates for use in refractories for the burning zone of cement kilns

    International Nuclear Information System (INIS)

    Ferreira, Luis Leonardo Horne Curimbaba

    2006-01-01

    Electro fused aggregates are largely used in refractory production due to the better performance reached when they are employed. In this work electro fused aggregates were designed for application in refractories for the burning zone of cement kilns. Initially reaction evaluation was conducted aiming the identification of the most prone refractory systems when single refractory phases react with Portland cement phases at high temperatures. In the next step, raw materials of the best refractory systems were electro fused to generate different aggregate compositions. The electro fused aggregates properties were evaluated and the classified ones were used to produce refractory bricks for the burning zone of cement kilns. General characteristics of these bricks were measured and compared with a standard magnesia-spinel refractory. Aggregates of the system Mg O - TiO 2 - Ca O, more specifically aggregates belonged to the compatibility triangle Mg O - Mg 2 TiO 4 - CaTiO 3 , showed suitable characteristics for development of refractories for the burning zone cement kilns. (author)

  19. Zirconium determination in refractories (gravimetric method)

    International Nuclear Information System (INIS)

    Capiotto, N.; Narahashi, Y.; Perish, C.G.; Souza, J.R.

    1991-01-01

    The zirconium determination in refractories is described, consisting in two separation methods for eliminating the interferences. The formatted product is calcined at 1100 0 C and determined gravimetrically as Zr P z 07. (author)

  20. Genetics of refractoriness to Plasmodium falciparum in the mosquito Anopheles stephensi

    NARCIS (Netherlands)

    Feldmann, A.M.; Gemert, Geert-Jan van; Vegte-Bolmer, Marga G. van de; Jansen, Ritsert C.

    1998-01-01

    We previously selected a line of the malaria vector mosquito Anopheles stephensi refractory (resistant) to the human malaria parasite Plasmodium falciparum, using in vitro infections with P. falciparum gametocytes. This report presents data on the genetic background of refractoriness. The results of

  1. Wet adhesion with application to tree frog adhesive toe pads and tires

    International Nuclear Information System (INIS)

    Persson, B N J

    2007-01-01

    Strong adhesion between solids with rough surfaces is only possible if at least one of the solids is elastically very soft. Some lizards and spiders are able to adhere (dry adhesion) and move on very rough vertical surfaces due to very compliant surface layers on their attachment pads. Flies, bugs, grasshoppers and tree frogs have less compliant pad surface layers, and in these cases adhesion to rough surfaces is only possible because the animals inject a wetting liquid into the pad-substrate contact area, which generates a relative long-range attractive interaction due to the formation of capillary bridges. In this presentation I will discuss some aspects of wet adhesion for tree frogs and give some comments related to tire applications

  2. Wet adhesion with application to tree frog adhesive toe pads and tires

    Energy Technology Data Exchange (ETDEWEB)

    Persson, B N J [IFF, FZ-Juelich, 52425 Juelich (Germany)

    2007-09-19

    Strong adhesion between solids with rough surfaces is only possible if at least one of the solids is elastically very soft. Some lizards and spiders are able to adhere (dry adhesion) and move on very rough vertical surfaces due to very compliant surface layers on their attachment pads. Flies, bugs, grasshoppers and tree frogs have less compliant pad surface layers, and in these cases adhesion to rough surfaces is only possible because the animals inject a wetting liquid into the pad-substrate contact area, which generates a relative long-range attractive interaction due to the formation of capillary bridges. In this presentation I will discuss some aspects of wet adhesion for tree frogs and give some comments related to tire applications.

  3. Productivity Costs in Patients with Refractory Chronic Rhinosinusitis

    Science.gov (United States)

    Rudmik, Luke; Smith, Timothy L.; Schlosser, Rodney J.; Hwang, Peter H.; Mace, Jess C.; Soler, Zachary M.

    2014-01-01

    Objective Disease-specific reductions in patient productivity can lead to substantial economic losses to society. The purpose of this study was to: 1) define the annual productivity cost for a patient with refractory chronic rhinosinusitis (CRS) and 2) evaluate the relationship between degree of productivity cost and CRS-specific characteristics. Study Design Prospective, multi-institutional, observational cohort study. Methods The human capital approach was used to define productivity costs. Annual absenteeism, presenteeism, and lost leisure time was quantified to define annual lost productive time (LPT). LPT was monetized using the annual daily wage rates obtained from the 2012 US National Census and the 2013 US Department of Labor statistics. Results A total of 55 patients with refractory CRS were enrolled. The mean work days lost related to absenteeism and presenteeism was 24.6 and 38.8 days per year, respectively. A total of 21.2 household days were lost per year related to daily sinus care requirements. The overall annual productivity cost was $10,077.07 per patient with refractory CRS. Productivity costs increased with worsening disease-specific QoL (r=0.440; p=0.001). Conclusion Results from this study have demonstrated that the annual productivity cost associated with refractory CRS is $10,077.07 per patient. This substantial cost to society provides a strong incentive to optimize current treatment protocols and continue evaluating novel clinical interventions to reduce this cost. PMID:24619604

  4. Productivity costs in patients with refractory chronic rhinosinusitis.

    Science.gov (United States)

    Rudmik, Luke; Smith, Timothy L; Schlosser, Rodney J; Hwang, Peter H; Mace, Jess C; Soler, Zachary M

    2014-09-01

    Disease-specific reductions in patient productivity can lead to substantial economic losses to society. The purpose of this study was to: 1) define the annual productivity cost for a patient with refractory chronic rhinosinusitis (CRS) and 2) evaluate the relationship between degree of productivity cost and CRS-specific characteristics. Prospective, multi-institutional, observational cohort study. The human capital approach was used to define productivity costs. Annual absenteeism, presenteeism, and lost leisure time was quantified to define annual lost productive time (LPT). LPT was monetized using the annual daily wage rates obtained from the 2012 U.S. National Census and the 2013 U.S. Department of Labor statistics. A total of 55 patients with refractory CRS were enrolled. The mean work days lost related to absenteeism and presenteeism were 24.6 and 38.8 days per year, respectively. A total of 21.2 household days were lost per year related to daily sinus care requirements. The overall annual productivity cost was $10,077.07 per patient with refractory CRS. Productivity costs increased with worsening disease-specific QoL (r = 0.440; p = 0.001). Results from this study have demonstrated that the annual productivity cost associated with refractory CRS is $10,077.07 per patient. This substantial cost to society provides a strong incentive to optimize current treatment protocols and continue evaluating novel clinical interventions to reduce this cost. © 2014 The American Laryngological, Rhinological and Otological Society, Inc.

  5. Refractory metal based superalloys

    International Nuclear Information System (INIS)

    Alonso, Paula R.; Vicente, Eduardo E.; Rubiolo, Gerardo H.

    1999-01-01

    Refractory metals are looked as promising materials for primary circuits in fission reactors and even as fusion reactor components. Indeed, superalloys could be developed which take advantage of their high temperature properties together with the benefits of a two- phase (intermetallic compound-refractory metal matrix) coherent structure. In 1993, researchers of the Office National d'Etudes et de Recherches Aerospatiales of France reported the observation of such a coherent structure in the Ta-Ti-Zr-Al-Nb-Mo system although the exact composition is not reported. The intermetallic compound would be Ti 2 AlMo based. However, the formation of this compound and its possible coexistence with a disordered bcc phase in the ternary system Ti-Al-Mo is a controversial subject in the related literature. In this work we develop a technique to obtain homogeneous alloys samples with 50 Ti-25 Al-25 Mo composition. The resulting specimens were characterized by optical and electronic metallography (SEM), microprobe composition measurements (EPMA) and X-ray diffraction (XRD) analyses. The results show the evidence for a bcc (A2→B2) ordering reaction in the Ti-Al-Mo system in the 50 Ti-25 Al-25 Mo composition. (author)

  6. Polymeric Materials for Aerospace Power and Propulsion: Overview of Polymer Research at NASA Glenn

    Science.gov (United States)

    Meador, Michael A.

    2007-01-01

    Weight, durability and performance are all major concerns for any NASA mission. Use of lightweight materials, such as fiber reinforced polymer matrix composites can lead to significant reductions in vehicle weight and improvements in vehicle performance. Research in the Polymeric Materials Branch at NASA Glenn is focused on improving the durability, properties, processability and performance of polymeric materials by utilizing both conventional polymer science and engineering as well as nanotechnology and bioinspired approaches. This presentation will provide an overview of these efforts and highlight recent progress.

  7. 76 FR 7847 - Glenn A. Baxter, Application To Renew License for Amateur Radio Service Station K1MAN

    Science.gov (United States)

    2011-02-11

    ... Renew License for Amateur Radio Service Station K1MAN AGENCY: Federal Communications Commission. ACTION... Service Station K1MAN filed by Glenn A. Baxter should be granted. DATES: The document was mailed to the... Amateur Radio Station K1MAN should be granted. As discussed below, the record before us indicates that...

  8. Felbamate in an adult population with severe refractory epilepsy.

    LENUS (Irish Health Repository)

    Kearney, H

    2011-04-05

    Felbamate (FBM) is efficacious in treating patients with refractory epilepsy but was withdrawn due to cases of aplastic anaemia, hepatic failure and five reported deaths. FBM is currently used in specialist centres and is only being used in one Irish centre to date. This papers aim is to review the efficacy and safety experience of FBM in Irish adult patients with refractory epilepsy. A retrospective chart review was done on patients\\' medical records. Patients were subdivided into responders and non responders based on change in seizure frequency and side effects were recorded for all. Of the 13 patients on FBM nine patients responded to FBM, four patients did not. FBM is a safe and efficacious alternative in an Irish adult population with refractory epilepsy. However close monitoring is still required given the potential fatal side effects that are possible with this anticonvulsant.

  9. Glenn Heat Transfer Simulation and Solver Graphical User Interface: Development and Testing

    Science.gov (United States)

    Kardamis, Joseph R.

    2004-01-01

    In the Tui ine Branch of the Turbomachinery and Propulsion Systems Division, researching and developing efficient turbine aerothermodynamics technologies is the main objective. Creating effective turbines for jet engines is a process which, if based purely on physical experimental testing, would be extremely expensive. It is for this reason, and also for the reasons of speed and ease, that the Turbine Branch spends a large amount of effort working with simulations of turbines. Specifically, they focus their work on two main fields: Computational Field Dynamics (CFD), and Experimental data analysis. The experimental field involves comparing experimental results to simulated results, whereas the CFD field involves running these simulations. The simulations are applied to aerodynamics and heat transfer cases, for both steady and unsteady flow conditions. By and large this work is applied to the domain of flow and heat transfer in axial turbines. The main application used to run these heat flow simulations is GlennHT. This program, recently rewritten in FORTRAN 90, allows the user to input a job file which specifies all the necessary parameters needed to simulate flow through a user-defined grid. There are several other executables used as well, ranging in application from converting grid files to and from particular formats, to merging blocks in a connectivity file, to converting connectivity files to a GlennHT compatible format. All of these executables are run from the command line in a terminal; some of them have interactive prompts where the user must specify the files to be manipulated after the program starts, while others take all of their parameters from the command line. With this amount of variation comes a good deal of commands and formats to memorize, which can cause slower and less efficient work, as users may forget how to execute a certain program, or not remember the pathnames of the files they wish to use. Two years ago, steps were made to expedite

  10. Intercellular adhesion molecule-1 augments myoblast adhesion and fusion through homophilic trans-interactions.

    Science.gov (United States)

    Pizza, Francis X; Martin, Ryan A; Springer, Evan M; Leffler, Maxwell S; Woelmer, Bryce R; Recker, Isaac J; Leaman, Douglas W

    2017-07-11

    The overall objective of the study was to identify mechanisms through which intercellular adhesion molecule-1 (ICAM-1) augments the adhesive and fusogenic properties of myogenic cells. Hypotheses were tested using cultured myoblasts and fibroblasts, which do not constitutively express ICAM-1, and myoblasts and fibroblasts forced to express full length ICAM-1 or a truncated form lacking the cytoplasmic domain of ICAM-1. ICAM-1 mediated myoblast adhesion and fusion were quantified using novel assays and cell mixing experiments. We report that ICAM-1 augments myoblast adhesion to myoblasts and myotubes through homophilic trans-interactions. Such adhesive interactions enhanced levels of active Rac in adherent and fusing myoblasts, as well as triggered lamellipodia, spreading, and fusion of myoblasts through the signaling function of the cytoplasmic domain of ICAM-1. Rac inhibition negated ICAM-1 mediated lamellipodia, spreading, and fusion of myoblasts. The fusogenic property of ICAM-1-ICAM-1 interactions was restricted to myogenic cells, as forced expression of ICAM-1 by fibroblasts did not augment their fusion to ICAM-1+ myoblasts/myotubes. We conclude that ICAM-1 augments myoblast adhesion and fusion through its ability to self-associate and initiate Rac-mediated remodeling of the actin cytoskeleton.

  11. Gecko adhesion pad: a smart surface?

    Science.gov (United States)

    Pesika, Noshir S.; Zeng, Hongbo; Kristiansen, Kai; Zhao, Boxin; Tian, Yu; Autumn, Kellar; Israelachvili, Jacob

    2009-11-01

    Recently, it has been shown that humidity can increase the adhesion of the spatula pads that form the outermost (adhesive) surface of the tokay gecko feet by 50% relative to the main adhesion mechanism (i.e. van der Waals adhesive forces), although the mechanism by which the enhancement is realized is still not well understood. A change in the surface hydrophobicity of a gecko setal array is observed when the array, which supports the spatulae, is exposed to a water drop for more than 20 min, suggesting a change in the hydrophilic-lyophilic balance (HLB), and therefore of the conformation of the surface proteins. A surface force apparatus (SFA) was used to quantify these changes, i.e. in the adhesion and friction forces, while shearing the setal array against a silica surface under (i) dry conditions, (ii) 100% humidity and (iii) when fully immersed in water. The adhesion increased in the humid environment but greatly diminished in water. Although the adhesion forces changed significantly, the friction forces remained unaffected, indicating that the friction between these highly textured surfaces is 'load-controlled' rather than 'adhesion-controlled'. These results demonstrate that the gecko adhesive pads have the ability to exploit environmental conditions to maximize their adhesion and stabilize their friction forces. Future designs of synthetic dry adhesives inspired by the gecko can potentially include similar 'smart' surfaces that adapt to their environment.

  12. Gecko adhesion pad: a smart surface?

    International Nuclear Information System (INIS)

    Pesika, Noshir S; Zeng Hongbo; Kristiansen, Kai; Israelachvili, Jacob; Zhao, Boxin; Tian Yu; Autumn, Kellar

    2009-01-01

    Recently, it has been shown that humidity can increase the adhesion of the spatula pads that form the outermost (adhesive) surface of the tokay gecko feet by 50% relative to the main adhesion mechanism (i.e. van der Waals adhesive forces), although the mechanism by which the enhancement is realized is still not well understood. A change in the surface hydrophobicity of a gecko setal array is observed when the array, which supports the spatulae, is exposed to a water drop for more than 20 min, suggesting a change in the hydrophilic-lyophilic balance (HLB), and therefore of the conformation of the surface proteins. A surface force apparatus (SFA) was used to quantify these changes, i.e. in the adhesion and friction forces, while shearing the setal array against a silica surface under (i) dry conditions, (ii) 100% humidity and (iii) when fully immersed in water. The adhesion increased in the humid environment but greatly diminished in water. Although the adhesion forces changed significantly, the friction forces remained unaffected, indicating that the friction between these highly textured surfaces is 'load-controlled' rather than 'adhesion-controlled'. These results demonstrate that the gecko adhesive pads have the ability to exploit environmental conditions to maximize their adhesion and stabilize their friction forces. Future designs of synthetic dry adhesives inspired by the gecko can potentially include similar 'smart' surfaces that adapt to their environment.

  13. MICROWAVE MEASUREMENT OF REFRACTORY MATERIALS AT HIGH-TEMPERATURE

    International Nuclear Information System (INIS)

    Kharkovsky, S.; Zoughi, R.; Smith, J.; Davis, B.; Limmer, R.

    2009-01-01

    Knowledge of the electrical behavior of refractory materials may enable the development and optimization of microwave nondestructive techniques to detect and evaluate changes in their physical properties while the materials are in service. This paper presents the results of a limited and preliminary investigation in which two refractory materials (dense chrome and dense zircon) were subjected to increasing temperature in a furnace and in which a frequency-modulated continuous-wave radar operating in the frequency range of 8-18 GHz radar was used to evaluate their attenuation properties.

  14. Microwave Measurement of Refractory Materials at High-Temperature

    Science.gov (United States)

    Kharkovsky, S.; Zoughi, R.; Smith, J.; Davis, B.; Limmer, R.

    2009-03-01

    Knowledge of the electrical behavior of refractory materials may enable the development and optimization of microwave nondestructive techniques to detect and evaluate changes in their physical properties while the materials are in service. This paper presents the results of a limited and preliminary investigation in which two refractory materials (dense chrome and dense zircon) were subjected to increasing temperature in a furnace and in which a frequency-modulated continuous-wave radar operating in the frequency range of 8-18 GHz radar was used to evaluate their attenuation properties.

  15. Ten patients with refractory status epilepticus in an intensive care department

    NARCIS (Netherlands)

    ter Maaten, JC; van Schijndel, RJM; Heimans, JJ; Schreuder, WO

    1998-01-01

    Status epilepticus (SE) is a serious disease, associated with a high morbidity and mortality, particularly if refractory to initial therapy. We describe the clinical manifestations and outcome in ten cases with refractory SE admitted to our medical intensive care unit. Three of these selected group

  16. Refractory absence epilepsy associated with GLUT-1 deficiency syndrome.

    LENUS (Irish Health Repository)

    Byrne, Susan

    2011-05-01

    GLUT-1 deficiency syndrome (GLUT-1 DS) is a disorder of cerebral glucose transport associated with early infantile epilepsy and microcephaly. We report two boys who presented with refractory absence epilepsy associated with hypoglycorrhachia, both of whom have genetically confirmed GLUT-1 DS. We propose that these children serve to expand the phenotype of GLUT-1 DS and suggest that this condition should be considered as a cause of refractory absence seizures in childhood.

  17. Treatment of Refractory Idiopathic Supraorbital Neuralgia Using Percutaneous Pulsed Radiofrequency.

    Science.gov (United States)

    Luo, Fang; Lu, Jingjing; Ji, Nan

    2018-02-26

    No ideal therapeutic method currently exists for refractory idiopathic supraorbital neuralgia patients who do not respond to conservative therapy, including medications and nerve blocks. Pulsed radiofrequency is a neuromodulation technique that does not produce sequelae of nerve damage after treatment. However, the efficacy of percutaneous pulsed radiofrequency for the treatment of refractory idiopathic supraorbital neuralgia is still not clear. The purpose of our study was to evaluate the efficacy and safety of pulsed radiofrequency treatment of the supraorbital nerve for refractory supraorbital neuralgia patients. We prospectively investigated the long-term effects of ultrasound-guided percutaneous pulsed radiofrequency in the treatment of 22 refractory idiopathic supraorbital neuralgia patients. A reduction in the verbal pain numeric rating scale score of more than 50% was used as the standard of effectiveness. The effectiveness rates at different time points within 2 years were calculated. After a single pulsed radiofrequency treatment, the effectiveness rate at 1 and 3 months was 77%, and the rates at 6 months, 1 year, and 2 years were 73%, 64%, and 50%, respectively. Except for a small portion of patients (23%) who experienced mild upper eyelid ecchymosis that gradually disappeared after approximately 2 weeks, no obvious complications were observed. In conclusion, the results of our study demonstrate that for patients with refractory idiopathic supraorbital neuralgia, percutaneous pulsed radiofrequency may be an effective and safe treatment choice. © 2018 World Institute of Pain.

  18. Surgical disconnection of patent paraumbilical vein in refractory hepatic encephalopathy.

    Science.gov (United States)

    Ishikawa, Yoshinori; Yoshida, Hiroshi; Mamada, Yasuhiro; Taniai, Nobuhiko; Bando, Koichi; Mizuguchi, Yoshiaki; Kakinuma, Daisuke; Kanda, Tomohiro; Akimaru, Koho; Tajiri, Takashi

    2008-06-01

    Refractory hepatic encephalopathy (HE) frequently develops in patients with cirrhosis and portal-systemic shunt. Recently, patients with refractory HE associated with portal-systemic shunt have been treated with interventional radiology. We describe a promising new treatment for portal-systemic shunt, ligation of the patent paraumbilical vein (PUV) after partial splenic embolization, in patients with refractory HE. Four patients with cirrhosis (3 women and 1 man; mean age, 56 years) and refractory HE due to a patent PUV were studied. Patency of the PUV had recurred in 1 patient after primary occlusion by interventional radiological procedures. The Child-Pugh class was B in 2 patients and C in 2. Before the present treatment, all patients had been hospitalized at least 3 times because of recurrent HE. Partial splenic embolization was performed in all patients to decrease portal venous pressure before surgery. Surgical ligation of the patent PUV was performed under epidural anesthesia. The patent PUV was carefully skeletonized and doubly ligated. Esophageal varices were evaluated with upper gastrointestinal endoscopy before and after surgery. The mean follow-up duration was 15.8 months. After ligation, there were no clinically significant complications. Esophageal varices were unchanged. The serum ammonia level was higher before surgery (162.3 +/- 56.4 mug/dL, mean +/- SD) than after surgery (41.8 +/- 20.2 mug/dL; p=0.0299). No patient had symptoms of HE. Ligation of the patent PUV is an effective treatment for patients with refractory HE.

  19. STS-95 Payload Specialist Glenn greets baseball legend Williams following a parade in Cocoa Beach

    Science.gov (United States)

    1998-01-01

    STS-95 Payload Specialist John H. Glenn Jr. (left) greets baseball legend Ted Williams at a reception at the Double Tree Oceanfront Hotel following a parade down State Road A1A in nearby Cocoa Beach. Organizers of the parade included the Cocoa Beach Area Chamber of Commerce, the Brevard County Tourist Development Council, and the cities of Cape Canaveral and Cocoa Beach. The parade is reminiscent of those held after missions during the Mercury Program.

  20. Bulk Vitrification Performance Enhancement: Refractory Lining Protection Against Molten Salt Penetration

    Energy Technology Data Exchange (ETDEWEB)

    Hrma, Pavel R.; Bagaasen, Larry M.; Schweiger, Michael J.; Evans, Michael B.; Smith, Benjamin T.; Arrigoni, Benjamin M.; Kim, Dong-Sang; Rodriguez, Carmen P.; Yokuda, Satoru T.; Matyas, Josef; Buchmiller, William C.; Gallegos, Autumn B.; Fluegel, Alexander

    2007-08-06

    Bulk vitrification (BV) is a process that heats a feed material that consists of glass-forming solids and dried low-activity waste (LAW) in a disposable refractory-lined metal box using electrical power supplied through carbon electrodes. The feed is heated to the point that the LAW decomposes and combines with the solids to generate a vitreous waste form. This study supports the BV design and operations by exploring various methods aimed at reducing the quantities of soluble Tc in the castable refractory block portion of the refractory lining, which limits the effectiveness of the final waste form.

  1. Comparison of Refractory Performance in Black Liquor Gasifiers and a Smelt Test System

    International Nuclear Information System (INIS)

    Peascoe, RA

    2001-01-01

    Prior laboratory corrosion studies along with experience at the black liquor gasifier in New Bern, North Carolina, clearly demonstrate that serious material problems exist with the gasifier's refractory lining. Mullite-based and alumina-based refractories used at the New Bern facility suffered significant degradation even though they reportedly performed adequately in smaller scale systems. Oak Ridge National Laboratory's involvement in the failure analysis, and the initial exploration of suitable replacement materials, led to the realization that a simple and reliable, complementary method for refractory screening was needed. The development of a laboratory test system and its suitability for simulating the environment of black liquor gasifiers was undertaken. Identification and characterization of corrosion products were used to evaluate the test system as a rapid screening tool for refractory performance and as a predictor of refractory lifetime. Results from the test systems and pl ants were qualitatively similar

  2. Optical adhesive property study

    Energy Technology Data Exchange (ETDEWEB)

    Sundvold, P.D.

    1996-01-01

    Tests were performed to characterize the mechanical and thermal properties of selected optical adhesives to identify the most likely candidate which could survive the operating environment of the Direct Optical Initiation (DOI) program. The DOI system consists of a high power laser and an optical module used to split the beam into a number of channels to initiate the system. The DOI requirements are for a high shock environment which current military optical systems do not operate. Five candidate adhesives were selected and evaluated using standardized test methods to determine the adhesives` physical properties. EC2216, manufactured by 3M, was selected as the baseline candidate adhesive based on the test results of the physical properties.

  3. Adhesion mechanism of a gecko-inspired oblique structure with an adhesive tip for asymmetric detachment

    International Nuclear Information System (INIS)

    Sekiguchi, Yu; Sato, Chiaki; Takahashi, Kunio

    2015-01-01

    An adhesion model of an oblique structure with an adhesive tip is proposed by considering a limiting stress for adhesion to describe the detachment mechanism of gecko foot hairs. When a force is applied to the root of the oblique structure, normal and shear stresses are generated at contact and the adhesive tip is detached from the surface when reaching the limiting stress. An adhesion criterion that considers both the normal and shear stresses is introduced, and the asymmetric detachment of the oblique structure is theoretically investigated. In addition, oblique beam array structures are manufactured, and an inclination effect of the structure on the asymmetric detachment is experimentally verified. (paper)

  4. Design methodology for nano-engineered surfaces to control adhesion: Application to the anti-adhesion of particles

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Taekyung [National Center for Optically-Assisted Ultra-High Precision Mechanical Systems, Yonsei University, Seoul 03722 (Korea, Republic of); School of Mechanical Engineering, Yonsei University, Seoul 03722 (Korea, Republic of); Min, Cheongwan [National Center for Optically-Assisted Ultra-High Precision Mechanical Systems, Yonsei University, Seoul 03722 (Korea, Republic of); Jung, Myungki; Lee, Jinhyung; Park, Changsu [National Center for Optically-Assisted Ultra-High Precision Mechanical Systems, Yonsei University, Seoul 03722 (Korea, Republic of); School of Mechanical Engineering, Yonsei University, Seoul 03722 (Korea, Republic of); Kang, Shinill, E-mail: snlkang@yonsei.ac.kr [National Center for Optically-Assisted Ultra-High Precision Mechanical Systems, Yonsei University, Seoul 03722 (Korea, Republic of); School of Mechanical Engineering, Yonsei University, Seoul 03722 (Korea, Republic of)

    2016-12-15

    Highlights: • A design method using the Derjaguin approximation with FEA for low-adhesion surface. • Fabrication of nanostructures with small adhesion forces by presented design method. • Characterization of adhesion force via AFM FD-curve with modified atypical tips. • Verification of low-adhesion of designed surfaces using centrifugal detachment tests. • Investigation of interdependence of hydrophobicity and anti-adhesion force. - Abstract: With increasing demand for means of controlling surface adhesion in various applications, including the semiconductor industry, optics, micro/nanoelectromechanical systems, and the medical industry, nano-engineered surfaces have attracted much attention. This study suggests a design methodology for nanostructures using the Derjaguin approximation in conjunction with finite element analysis for the control of adhesion forces. The suggested design methodology was applied for designing a nano-engineered surface with low-adhesion properties. To verify this, rectangular and sinusoidal nanostructures were fabricated and analyzed using force-distance curve measurements using atomic force microscopy and centrifugal detachment testing. For force-distance curve measurements, modified cantilevers with tips formed with atypical particles were used. Subsequently, centrifugal detachment tests were also conducted. The surface wettability of rectangular and sinusoidal nanostructures was measured and compared with the measured adhesion force and the number of particles remaining after centrifugal detachment tests.

  5. Operating The Central Process Systems At Glenn Research Center

    Science.gov (United States)

    Weiler, Carly P.

    2004-01-01

    As a research facility, the Glenn Research Center (GRC) trusts and expects all the systems, controlling their facilities to run properly and efficiently in order for their research and operations to occur proficiently and on time. While there are many systems necessary for the operations at GRC, one of those most vital systems is the Central Process Systems (CPS). The CPS controls operations used by GRC's wind tunnels, propulsion systems lab, engine components research lab, and compressor, turbine and combustor test cells. Used widely throughout the lab, it operates equipment such as exhausters, chillers, cooling towers, compressors, dehydrators, and other such equipment. Through parameters such as pressure, temperature, speed, flow, etc., it performs its primary operations on the major systems of Electrical Dispatch (ED), Central Air Dispatch (CAD), Central Air Equipment Building (CAEB), and Engine Research Building (ERB). In order for the CPS to continue its operations at Glenn, a new contract must be awarded. Consequently, one of my primary responsibilities was assisting the Source Evaluation Board (SEB) with the process of awarding the recertification contract of the CPS. The job of the SEB was to evaluate the proposals of the contract bidders and then to present their findings to the Source Selecting Official (SSO). Before the evaluations began, the Center Director established the level of the competition. For this contract, the competition was limited to those companies classified as a small, disadvantaged business. After an industry briefing that explained to qualified companies the CPS and type of work required, each of the interested companies then submitted proposals addressing three components: Mission Suitability, Cost, and Past Performance. These proposals were based off the Statement of Work (SOW) written by the SEB. After companies submitted their proposals, the SEB reviewed all three components and then presented their results to the SSO. While the

  6. Gecko adhesion pad: a smart surface?

    Energy Technology Data Exchange (ETDEWEB)

    Pesika, Noshir S [Chemical and Biomolecular Engineering Department, Tulane University, New Orleans, LA 70118 (United States); Zeng Hongbo [Chemical and Materials Engineering Department, University of Alberta, Edmonton, AB, T6G 2V4 (Canada); Kristiansen, Kai; Israelachvili, Jacob [Chemical Engineering Department, University of California, Santa Barbara, CA 93117 (United States); Zhao, Boxin [Chemical Engineering Department and Waterloo Institute of Nanotechnology, University of Waterloo, Ontario, N2L 3G1 (Canada); Tian Yu [State Key Laboratory of Tribology, Department of Precision Instruments, Tsinghua University, Beijing 100084 (China); Autumn, Kellar, E-mail: npesika@tulane.ed [Department of Biology, Lewis and Clark College, Portland, OR 97219 (United States)

    2009-11-18

    Recently, it has been shown that humidity can increase the adhesion of the spatula pads that form the outermost (adhesive) surface of the tokay gecko feet by 50% relative to the main adhesion mechanism (i.e. van der Waals adhesive forces), although the mechanism by which the enhancement is realized is still not well understood. A change in the surface hydrophobicity of a gecko setal array is observed when the array, which supports the spatulae, is exposed to a water drop for more than 20 min, suggesting a change in the hydrophilic-lyophilic balance (HLB), and therefore of the conformation of the surface proteins. A surface force apparatus (SFA) was used to quantify these changes, i.e. in the adhesion and friction forces, while shearing the setal array against a silica surface under (i) dry conditions, (ii) 100% humidity and (iii) when fully immersed in water. The adhesion increased in the humid environment but greatly diminished in water. Although the adhesion forces changed significantly, the friction forces remained unaffected, indicating that the friction between these highly textured surfaces is 'load-controlled' rather than 'adhesion-controlled'. These results demonstrate that the gecko adhesive pads have the ability to exploit environmental conditions to maximize their adhesion and stabilize their friction forces. Future designs of synthetic dry adhesives inspired by the gecko can potentially include similar 'smart' surfaces that adapt to their environment.

  7. Adhesion and multi-materials

    International Nuclear Information System (INIS)

    Schultz, J.

    1997-01-01

    Adhesion is a multidisciplinary science relevant to many practical fields. The main application of adhesion is bonding by adhesives. This technique is widely used in the industrial world and more specifically in the advanced technical domains. Adhesion is also involved in multi-component materials such as coatings, multilayer materials, polymer blends, composite materials... The multidisciplinary aspect of adhesion is well demonstrated by considering the wide variety of concepts, models and theories proposed for its description. An example of the adhesion between a fiber and a matrix in a composite material will lead to a general model relating the molecular properties of the interface to its capacity of stress transfer and hence to the macroscopic mechanical properties of the composite. This relationship is valid whatever the fiber (glass, carbon, polymeric) or the polymer matrix (thermoplastics, thermosetting). Any deviation from this model can be attributed to the existence of an interfacial zone or interphase exhibiting properties, mainly mechanical properties, different from the bulk matrix. Two examples are examined: the first one deals with the creation of a trans crystalline interphase in a semi-crystalline thermoplastic matrix and the second one is concerned with the formation of a pseudo glassy interphase in an elastomer matrix. These examples stress the need for complementary approaches in the understanding of adhesion phenomena at different levels of knowledge, from molecular to macroscopic. They also show how important it is to understand the mechanisms of formation of inter phases in order to be able to master the performance of multicomponent materials. (Author)

  8. Oral tranexamic acid lightens refractory melasma.

    Science.gov (United States)

    Tan, Aaron Wei Min; Sen, Priya; Chua, Sze Hon; Goh, Boon Kee

    2017-08-01

    Melasma is a common acquired hyperpigmentary disorder, particularly among Asians and Hispanics, but its exact pathomechanism is poorly understood. Tranexamic acid has been found to lighten melasma by interfering with the interaction of melanocytes and keratinocytes by inhibiting the plasminogen/plasmin system. The aim was to evaluate the therapeutic effects of oral tranexamic acid in the treatment of melasma refractory to topical skin-lightening agents. This retrospective study analyses patients with melasma recruited from a tertiary dermatological centre in Singapore between 1 August 2009 and 31 March 2011. The patients chosen had refractory melasma treated with oral tranexamic acid 250 mg twice daily in addition to pre-existing combination topical therapy. Objective assessment using the physician's global assessment and melasma area and severity index (MASI) scores were performed based on a post-hoc analysis of photographic records by three independent physicians. A paired t-test was used to evaluate the changes in the MASI scores pre-therapy and post-treatment. Statistical significance was defined as P tranexamic acid for a mean period of 3.7 ± 0.33 months, in addition to combination topical therapy. Their mean age was 47.2 ± 1.61 years. The mean MASI scores after tranexamic acid treatment (2.7 ± 1.6) were significantly lower (P tranexamic acid can serve as a safe and useful adjunct in the treatment of refractory melasma. © 2016 The Australasian College of Dermatologists.

  9. Comparing Soy Flour Wood Adhesives to Purified Soy Protein Adhesives

    Science.gov (United States)

    Charles R. Frihart; Linda F. Lorenz

    2013-01-01

    While economics dictate that soy-based wood adhesives be made with soy flour, much of the recent literature on soy-based wood adhesives has involved using soy protein isolate. The obvious assumption is that the additional carbohydrates in the flour but not in the isolate only serve as inert diluents. Our studies have shown that the isolate can provide 10 times the wet...

  10. Clinical features and course of refractory anemia with ring sideroblasts associated with marked thrombocytosis

    Science.gov (United States)

    Broseus, Julien; Florensa, Lourdes; Zipperer, Esther; Schnittger, Susanne; Malcovati, Luca; Richebourg, Steven; Lippert, Eric; Cermak, Jaroslav; Evans, Jyoti; Mounier, Morgane; Raya, José Maria; Bailly, François; Gattermann, Norbert; Haferlach, Torsten; Garand, Richard; Allou, Kaoutar; Besses, Carlos; Germing, Ulrich; Haferlach, Claudia; Travaglino, Erica; Luno, Elisa; Pinan, Maria Angeles; Arenillas, Leonor; Rozman, Maria; Perez Sirvent, Maria Luz; Favre, Bernardine; Guy, Julien; Alonso, Esther; Ahwij, Nuhri; Jerez, Andrés; Hermouet, Sylvie; Maynadié, Marc; Cazzola, Mario; Girodon, François

    2012-01-01

    Background Refractory anemia with ring sideroblasts associated with marked thrombocytosis was proposed as a provisional entity in the 2001 World Health Organization classification of myeloid neoplasms and also in the 2008 version, but its existence as a single entity is contested. We wish to define the clinical features of this rare myelodysplastic/myeloproliferative neoplasm and to compare its clinical outcome with that of refractory anemia with ring sideroblasts and essential thrombocythemia. Design and Methods We conducted a collaborative retrospective study across Europe. Our database included 200 patients diagnosed with refractory anemia with ring sideroblasts and marked thrombocytosis. For each of these patients, each patient diagnosed with refractory anemia with ring sideroblasts was matched for age and sex. At the same time, a cohort of 454 patients with essential thrombocythemia was used to compare outcomes of the two diseases. Results In patients with refractory anemia with ring sideroblasts and marked thrombocytosis, depending on the Janus Kinase 2 V617F mutational status (positive or negative) or platelet threshold (over or below 600×109/L), no difference in survival was noted. However, these patients had shorter overall survival and leukemia-free survival with a lower risk of thrombotic complications than did patients with essential thrombocythemia (P<0.001) but better survival (P<0.001) and a higher risk of thrombosis (P=0.039) than patients with refractory anemia with ring sideroblasts. Conclusions The clinical course of refractory anemia with ring sideroblasts and marked thrombocytosis is better than that of refractory anemia with ring sideroblasts and worse than that of essential thrombocythemia. The higher risk of thrombotic events in this disorder suggests that anti-platelet therapy might be considered in this subset of patients. From a clinical point of view, it appears to be important to consider refractory anemia with ring sideroblasts and

  11. Nanostructured refractory thin films for solar applications

    Science.gov (United States)

    Ollier, E.; Dunoyer, N.; Dellea, O.; Szambolics, H.

    2014-08-01

    Selective solar absorbers are key elements of all solar thermal systems. Solar thermal panels and Concentrated Solar Power (CSP) systems aim respectively at producing heat and electricity. In both cases, a surface receives the solar radiation and is designed to have the highest optical absorption (lowest optical reflectivity) of the solar radiation in the visible wavelength range where the solar intensity is the highest. It also has a low emissivity in the infrared (IR) range in order to avoid radiative thermal losses. Current solutions in the state of the art usually consist in deposited interferential thin films or in cermets [1]. Structured surfaces have been proposed and have been simulated because they are supposed to be more efficient when the solar radiation is not normal to the receiving surface and because they could potentially be fabricated with refractory materials able to sustain high operating temperatures. This work presents a new method to fabricate micro/nanostructured surfaces on molybdenum (refractory metal with a melting temperature of 2623°C). This method now allows obtaining a refractory selective surface with an excellent optical selectivity and a very high absorption in the visible range. This high absorption performance was obtained by achieving a double structuration at micro and nano scales thanks to an innovative process flow.

  12. Low-Chrome/Chrome Free Refractories for Slagging Gasifiers

    International Nuclear Information System (INIS)

    Bennett, J.P.; Kwong, K.-S.; Powell, C.P.; Thomas, H.; Petty, A.V. Jr.

    2007-01-01

    Gasifiers are containment vessels used to react carbon-containing materials with oxygen and water, producing syngas (CO and H2) that is used in chemical and power production. It is also a potential source of H2 in a future hydrogen economy. Air cooled slagging gasifiers are one type of gasifier, operating at temperatures from 1275-1575 C and at pressures of 400 psi or higher. They typically use coal or petroleum coke as the carbon source, materials which contain ash impurities that liquefy at the gasification temperatures, producing liquid slag in quantities of 100 or more tons/day, depending on the carbon fed rate and the percent ash present in the feedstock. The molten slag is corrosive to refractory linings, causing chemical dissolution and spalling. The refractory lining is composed of chrome oxide, alumina, and zirconia; and is replaced every 3-24 months. Gasifier users would like greater on-line availability and reliability of gasifier liners, something that has impacted gasifier acceptance by industry. Research is underway at NETL to improve refractory service life and to develop a no-chrome or low-chrome oxide alternative refractory liner. Over 250 samples of no- or low-chrome oxide compositions have been evaluated for slag interactions by cup testing; with potential candidates for further studies including those with ZrO2, Al2O3, and MgO materials. The development of improved liner materials is necessary if technologies such as IGCC and DOE's Near Zero Emissions Advanced Fossil Fuel Power Plant are to be successful and move forward in the marketplace

  13. Long-term evaluation of treatment of chronic, therapeutically refractory tinnitus by neurostimulation

    NARCIS (Netherlands)

    Staal, M. J.; Holm, A. F.; Mooij, J. J. A.; Albers, F. W. J.; Bartels, H.

    2007-01-01

    Objective: Long-term evaluation of treatment of chronic, therapeutically refractory tinnitus by means of chronic electrical stimulation of the vestibulocochlear nerve. Patients: Inclusion criteria were severe, chronic, therapeutically refractory, unilateral tinnitus and severe hearing loss at the

  14. Super-Refractory Status Epilepticus: Report of a Case and Review of the Literature.

    Science.gov (United States)

    Lapenta, Leonardo; Frisullo, Giovanni; Vollono, Catello; Brunetti, Valerio; Giannantoni, Nadia Mariagrazia; Sandroni, Claudio; Di Lella, Giuseppe; Della Marca, Giacomo

    2015-10-01

    Super-refractory status epilepticus (SE; ie, SE continuing or recurring despite 24 hours of general anesthesia) is a severe condition with high percentage of mortality and morbidity. Usually, this condition occurs because of serious brain damage; nevertheless, some patients develop super-refractory SE without identifiable etiology. Although not uncommonly encountered in neurointensive care, scientific data on this condition are still lacking in terms of treatment and prognosis. Herein, we report a case of super-refractory SE with recovery after 50 days, despite electroencephalographic (EEG) and magnetic resonance imaging (MRI) signs traditionally related to poor prognosis. A review of the literature on super-refractory SE is also presented. © EEG and Clinical Neuroscience Society (ECNS) 2014.

  15. Proposed Development of NASA Glenn Research Center's Aeronautical Network Research Simulator

    Science.gov (United States)

    Nguyen, Thanh C.; Kerczewski, Robert J.; Wargo, Chris A.; Kocin, Michael J.; Garcia, Manuel L.

    2004-01-01

    Accurate knowledge and understanding of data link traffic loads that will have an impact on the underlying communications infrastructure within the National Airspace System (NAS) is of paramount importance for planning, development and fielding of future airborne and ground-based communications systems. Attempting to better understand this impact, NASA Glenn Research Center (GRC), through its contractor Computer Networks & Software, Inc. (CNS, Inc.), has developed an emulation and test facility known as the Virtual Aircraft and Controller (VAC) to study data link interactions and the capacity of the NAS to support Controller Pilot Data Link Communications (CPDLC) traffic. The drawback of the current VAC test bed is that it does not allow the test personnel and researchers to present a real world RF environment to a complex airborne or ground system. Fortunately, the United States Air Force and Navy Avionics Test Commands, through its contractor ViaSat, Inc., have developed the Joint Communications Simulator (JCS) to provide communications band test and simulation capability for the RF spectrum through 18 GHz including Communications, Navigation, and Identification and Surveillance functions. In this paper, we are proposing the development of a new and robust test bed that will leverage on the existing NASA GRC's VAC and the Air Force and Navy Commands JCS systems capabilities and functionalities. The proposed NASA Glenn Research Center's Aeronautical Networks Research Simulator (ANRS) will combine current Air Traffic Control applications and physical RF stimulation into an integrated system capable of emulating data transmission behaviors including propagation delay, physical protocol delay, transmission failure and channel interference. The ANRS will provide a simulation/stimulation tool and test bed environment that allow the researcher to predict the performance of various aeronautical network protocol standards and their associated waveforms under varying

  16. Tioguanine in the treatment of refractory coeliac disease--a single centre experience.

    Science.gov (United States)

    Tack, G J; van Asseldonk, D P; van Wanrooij, R L J; van Bodegraven, A A; Mulder, C J

    2012-08-01

    Refractory coeliac disease type I is a complicated form of coeliac disease characterised by primary or secondary resistance to a gluten-free diet with persisting or reoccurring intestinal villous atrophy and symptoms of malabsorption. Besides corticosteroids, azathioprine has been advocated for the treatment of refractory coeliac disease type I. However, tioguanine (TG) might be better tolerated and more efficacious owing to a simpler metabolism towards bioactivation. To evaluate tolerability and effectiveness of the nonconventional thiopurine derivative TG in refractory coeliac disease type I. Refractory coeliac disease type I patients treated with TG between June 2001 and November 2010 with a follow-up period of at least 1 year were included. Adverse events, laboratory values, 6-thioguanine nucleotide concentrations and rates of both clinical and histological response were evaluated at baseline and during follow-up. Twelve adult refractory coeliac disease type I patients were included. The median TG treatment duration was 14 months. Ten patients tolerated TG treatment on the long term, whereas two patients withdrew treatment due to adverse events. No nodular regenerative hyperplasia of the liver was observed. During follow-up clinical and histological response was observed in 83% and 78%, respectively. Corticosteroid dependency decreased by 50%. Tioguanine appears to be a convenient drug for the treatment of refractory coeliac disease type I based on higher histological and similar clinical response rates as compared with historical conventional therapies. © 2012 Blackwell Publishing Ltd.

  17. Refractory, Abrasive and Other Industrial Mineral Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes refractory, abrasive, and other industrial minerals operations in the United States. The data represent commodities covered by the Minerals...

  18. Evaluation of nutritional status in children with refractory epilepsy

    Directory of Open Access Journals (Sweden)

    Testolin G

    2006-04-01

    Full Text Available Abstract Background children affected by refractory epilepsy could be at risk of malnutrition because of feeding difficulties (anorexia, chewing, swallowing difficulties or vomiting and chronic use of anticonvulsants, which may affect food intake and energy metabolism. Moreover, their energy requirement may be changed as their disabilities would impede normal daily activities. The aim of the present study was to evaluate nutritional status, energy metabolism and food intake in children with refractory epilepsy. Methods 17 children with refractory epilepsy (13 boys and 4 girls; mean age 9 ± 3,2 years; Body Mass Index 15,7 ± 3,6 underwent an anthropometric assessment, body composition evaluation by dual-energy X-ray absorptiometry, detailed dietetic survey and measurement of resting energy expenditure by indirect calorimetry. Weight-for-age, height-for-age (stunting and weight-for-height (wasting were estimated compared to those of a reference population of the same age. Results 40% of children were malnourished and 24% were wasted. The nutritional status was worse in the more disabled children. Dietary intake resulted unbalanced (18%, 39%, 43% of total daily energy intake derived respectively from protein, lipid and carbohydrate. Adequacy index [nutrient daily intake/recommended allowance (RDA × 100] was Conclusion many children with refractory epilepsy would benefit from individual nutritional assessment and management as part of their overall care.

  19. Hierarchical macroscopic fibrillar adhesives: in situ study of buckling and adhesion mechanisms on wavy substrates.

    Science.gov (United States)

    Bauer, Christina T; Kroner, Elmar; Fleck, Norman A; Arzt, Eduard

    2015-10-23

    Nature uses hierarchical fibrillar structures to mediate temporary adhesion to arbitrary substrates. Such structures provide high compliance such that the flat fibril tips can be better positioned with respect to asperities of a wavy rough substrate. We investigated the buckling and adhesion of hierarchically structured adhesives in contact with flat smooth, flat rough and wavy rough substrates. A macroscopic model for the structural adhesive was fabricated by molding polydimethylsiloxane into pillars of diameter in the range of 0.3-4.8 mm, with up to three different hierarchy levels. Both flat-ended and mushroom-shaped hierarchical samples buckled at preloads one quarter that of the single level structures. We explain this behavior by a change in the buckling mode; buckling leads to a loss of contact and diminishes adhesion. Our results indicate that hierarchical structures can have a strong influence on the degree of adhesion on both flat and wavy substrates. Strategies are discussed that achieve highly compliant substrates which adhere to rough substrates.

  20. Improvement of castable refractories for RH snorkel; RH shinshitsukanyo futeikeizai no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Nishi, K.; Obana, T.; Fijii, T.; Shimizu, I. [Harima Ceramics Corp., Hyogo (Japan)

    1999-11-01

    Relating to corrosion of RH submerged nozzle, resistance against iron oxide of monolithic refractories was examined. Corrosion and seepage of refractories were measured by rotating corrosion, refractories include alumina-spinel castable, which is applied to RH under tank, and alumina-magnesia castable, which is generally used for RH, submerged nozzle. Alumina-spinel castable is superior in resistance against iron oxide than alumina-magnesia castable, and the resistance decreased with increase of stainless fiber addition to castable. Alumina-spinel castable without stainless fiber was suitable for bottom end of the dipping pipe. (NEDO)

  1. Influence of substrate modulus on gecko adhesion

    Science.gov (United States)

    Klittich, Mena R.; Wilson, Michael C.; Bernard, Craig; Rodrigo, Rochelle M.; Keith, Austin J.; Niewiarowski, Peter H.; Dhinojwala, Ali

    2017-03-01

    The gecko adhesion system fascinates biologists and materials scientists alike for its strong, reversible, glue-free, dry adhesion. Understanding the adhesion system’s performance on various surfaces can give clues as to gecko behaviour, as well as towards designing synthetic adhesive mimics. Geckos encounter a variety of surfaces in their natural habitats; tropical geckos, such as Gekko gecko, encounter hard, rough tree trunks as well as soft, flexible leaves. While gecko adhesion on hard surfaces has been extensively studied, little work has been done on soft surfaces. Here, we investigate for the first time the influence of macroscale and nanoscale substrate modulus on whole animal adhesion on two different substrates (cellulose acetate and polydimethylsiloxane) in air and find that across 5 orders of magnitude in macroscale modulus, there is no change in adhesion. On the nanoscale, however, gecko adhesion is shown to depend on substrate modulus. This suggests that low surface-layer modulus may inhibit the gecko adhesion system, independent of other influencing factors such as macroscale composite modulus and surface energy. Understanding the limits of gecko adhesion is vital for clarifying adhesive mechanisms and in the design of synthetic adhesives for soft substrates (including for biomedical applications and wearable electronics).

  2. Effectiveness of intravenous levetiracetam as an adjunctive treatment in pediatric refractory status epilepticus.

    Science.gov (United States)

    Kim, Jon Soo; Lee, Jeong Ho; Ryu, Hye Won; Lim, Byung Chan; Hwang, Hee; Chae, Jong-Hee; Choi, Jieun; Kim, Ki Joong; Hwang, Yong Seung; Kim, Hunmin

    2014-08-01

    Intravenous levetiracetam (LEV) has been shown to be effective and safe in treating adults with refractory status epilepticus (SE). We sought to investigate the efficacy and safety of intravenous LEV for pediatric patients with refractory SE. We performed a retrospective medical-record review of pediatric patients who were treated with intravenous LEV for refractory SE. Clinical information regarding age, sex, seizure type, and underlying neurological status was collected. We evaluated other anticonvulsants that were used prior to administration of intravenous LEV and assessed loading dose, response to treatment, and any adverse events from intravenous LEV administration. Fourteen patients (8 boys and 6 girls) received intravenous LEV for the treatment of refractory SE. The mean age of the patients was 4.4 ± 5.5 years (range, 4 days to 14.6 years). Ten of the patients were neurologically healthy prior to the refractory SE, and the other 4 had been previously diagnosed with epilepsy. The mean loading dose of intravenous LEV was 26 ± 4.6 mg/kg (range, 20-30 mg/kg). Seizure termination occurred in 6 (43%) of the 14 patients. In particular, 4 (57%) of the 7 patients younger than 2 years showed seizure termination. No immediate adverse events occurred during or after infusions. The current study demonstrated that the adjunctive use of intravenous LEV was effective and well tolerated in pediatric patients with refractory SE, even in patients younger than 2 years. Intravenous LEV should be considered as an effective and safe treatment option for refractory SE in pediatric patients.

  3. The neural cell adhesion molecule

    DEFF Research Database (Denmark)

    Berezin, V; Bock, E; Poulsen, F M

    2000-01-01

    During the past year, the understanding of the structure and function of neural cell adhesion has advanced considerably. The three-dimensional structures of several of the individual modules of the neural cell adhesion molecule (NCAM) have been determined, as well as the structure of the complex...... between two identical fragments of the NCAM. Also during the past year, a link between homophilic cell adhesion and several signal transduction pathways has been proposed, connecting the event of cell surface adhesion to cellular responses such as neurite outgrowth. Finally, the stimulation of neurite...

  4. Nucleation and growth of cadherin adhesions

    International Nuclear Information System (INIS)

    Lambert, Mireille; Thoumine, Olivier; Brevier, Julien; Choquet, Daniel; Riveline, Daniel; Mege, Rene-Marc

    2007-01-01

    Cell-cell contact formation relies on the recruitment of cadherin molecules and their anchoring to actin. However, the precise chronology of events from initial cadherin trans-interactions to adhesion strengthening is unclear, in part due to the lack of access to the distribution of cadherins within adhesion zones. Using N-cadherin expressing cells interacting with N-cadherin coated surfaces, we characterized the formation of cadherin adhesions at the ventral cell surface. TIRF and RIC microscopies revealed streak-like accumulations of cadherin along actin fibers. FRAP analysis indicated that engaged cadherins display a slow turnover at equilibrium, compatible with a continuous addition and removal of cadherin molecules within the adhesive contact. Association of cadherin cytoplasmic tail to actin as well as actin cables and myosin II activity are required for the formation and maintenance of cadherin adhesions. Using time lapse microscopy we deciphered how cadherin adhesions form and grow. As lamellipodia protrude, cadherin foci stochastically formed a few microns away from the cell margin. Neo-formed foci coalesced aligned and coalesced with preformed foci either by rearward sliding or gap filling to form cadherin adhesions. Foci experienced collapse at the rear of cadherin adhesions. Based on these results, we present a model for the nucleation, directional growth and shrinkage of cadherin adhesions

  5. Adhesive Bonding and Corrosion Performance Investigated as a Function of Aluminum Oxide Chemistry and Adhesives

    NARCIS (Netherlands)

    Abrahami, S.T.; Hauffman, T.; de Kok, John M.M.; Terryn, H.A.; Mol, J.M.C.

    2017-01-01

    The long-term strength and durability of an adhesive bond is dependent on the stability of the oxide-adhesive interface. As such, changes in the chemistry of the oxide and/or the adhesive are expected to modify the interfacial properties and affect the joint performance in practice. The upcoming

  6. Soy protein adhesives

    Science.gov (United States)

    Charles R. Frihart

    2010-01-01

    In the quest to manufacture and use building materials that are more environmentally friendly, soy adhesives can be an important component. Trees fix and store carbon dioxide in the atmosphere. After the trees are harvested, machinery converts the wood into strands, which are then bonded together with adhesives to form strandboard, used in constructing long-lasting...

  7. Temperature Effects on Adhesive Bond Strengths and Modulus for Commonly Used Spacecraft Structural Adhesives

    Science.gov (United States)

    Ojeda, Cassandra E.; Oakes, Eric J.; Hill, Jennifer R.; Aldi, Dominic; Forsberg, Gustaf A.

    2011-01-01

    A study was performed to observe how changes in temperature and substrate material affected the strength and modulus of an adhesive bondline. Seven different adhesives commonly used in aerospace bonded structures were tested. Aluminum, titanium and Invar adherends were cleaned and primed, then bonded using the manufacturer's recommendations. Following surface preparation, the coupons were bonded with the adhesives. The single lap shear coupons were then pull tested per ASTM D 1002 Standard Test Method for Apparent Shear Strength of Single- Lap-Joint over a temperature range from -150 deg C up to +150 deg C. The ultimate strength was calculated and the resulting data were converted into B-basis design allowables. Average and Bbasis results were compared. Results obtained using aluminum adherends are reported. The effects of using different adherend materials and temperature were also studied and will be reported in a subsequent paper. Dynamic Mechanical Analysis (DMA) was used to study variations in adhesive modulus with temperature. This work resulted in a highly useful database for comparing adhesive performance over a wide range of temperatures, and has facilitated selection of the appropriate adhesive for spacecraft structure applications.

  8. Regulative mechanisms of chondrocyte adhesion

    DEFF Research Database (Denmark)

    Schmal, Hagen; Mehlhorn, Alexander T; Fehrenbach, Miriam

    2006-01-01

    Interaction between chondrocytes and extracellular matrix is considered a key factor in the generation of grafts for matrix-associated chondrocyte transplantation. Therefore, our objective was to study the influence of differentiation status on cellular attachment. Adhesion of chondrocytes...... to collagen type II increased after removal from native cartilage up to the third day in monolayer in a dose-dependent manner. Following dedifferentiation after the second passage, adhesion to collagen types I (-84%) and II (-46%) decreased, whereas adhesion to fibrinogen (+59%) and fibronectin (+43......%) increased. A cartilage construct was developed based on a clinically established collagen type I scaffold. In this matrix, more than 80% of the cells could be immobilized by mechanisms of adhesion, filtration, and cell entrapment. Confocal laser microscopy revealed focal adhesion sites as points of cell...

  9. Neuroimaging in refractory epilepsy. Current practice and evolving trends

    Energy Technology Data Exchange (ETDEWEB)

    Ramli, N. [Department of Biomedical Imaging, University Malaya Research Imaging Centre (Malaysia); Rahmat, K., E-mail: katt_xr2000@yahoo.com [Department of Biomedical Imaging, University Malaya Research Imaging Centre (Malaysia); Lim, K.S.; Tan, C.T. [Neurology Unit, Department of Medicine, University Malaya, Kuala Lumpur (Malaysia)

    2015-09-15

    Highlights: • Neuroimaging is imperative in diagnostic work up and therapeutic assessment of refractory epilepsy. • Identification of epileptogenic zone on EEG, MRI and functional imaging improves the success of surgery. • High performance MRI greatly enhanced metabolic information and elucidate brain functions. • Optimisation of epilepsy protocols in structural and functional MRI are presented in this article. - Abstract: Identification of the epileptogenic zone is of paramount importance in refractory epilepsy as the success of surgical treatment depends on complete resection of the epileptogenic zone. Imaging plays an important role in the locating and defining anatomic epileptogenic abnormalities in patients with medically refractory epilepsy. The aim of this article is to present an overview of the current MRI sequences used in epilepsy imaging with special emphasis of lesion seen in our practices. Optimisation of epilepsy imaging protocols are addressed and current trends in functional MRI sequences including MR spectroscopy, diffusion tensor imaging and fusion MR with PET and SPECT are discussed.

  10. Neuroimaging in refractory epilepsy. Current practice and evolving trends

    International Nuclear Information System (INIS)

    Ramli, N.; Rahmat, K.; Lim, K.S.; Tan, C.T.

    2015-01-01

    Highlights: • Neuroimaging is imperative in diagnostic work up and therapeutic assessment of refractory epilepsy. • Identification of epileptogenic zone on EEG, MRI and functional imaging improves the success of surgery. • High performance MRI greatly enhanced metabolic information and elucidate brain functions. • Optimisation of epilepsy protocols in structural and functional MRI are presented in this article. - Abstract: Identification of the epileptogenic zone is of paramount importance in refractory epilepsy as the success of surgical treatment depends on complete resection of the epileptogenic zone. Imaging plays an important role in the locating and defining anatomic epileptogenic abnormalities in patients with medically refractory epilepsy. The aim of this article is to present an overview of the current MRI sequences used in epilepsy imaging with special emphasis of lesion seen in our practices. Optimisation of epilepsy imaging protocols are addressed and current trends in functional MRI sequences including MR spectroscopy, diffusion tensor imaging and fusion MR with PET and SPECT are discussed

  11. Adhesion molecules

    CERN Document Server

    Preedy, Victor R

    2016-01-01

    This book covers the structure and classification of adhesion molecules in relation to signaling pathways and gene expression. It discusses immunohistochemical localization, neutrophil migration, and junctional, functional, and inflammatory adhesion molecules in pathologies such as leukocyte decompression sickness and ischemia reperfusion injury. Highlighting the medical applications of current research, chapters cover diabetes, obesity, and metabolic syndrome; hypoxia; kidney disease; smoking, atrial fibrillation, and heart disease, the brain and dementia; and tumor proliferation. Finally, it looks at molecular imaging and bioinformatics, high-throughput technologies, and chemotherapy.

  12. Current dental adhesives systems. A narrative review.

    Science.gov (United States)

    Milia, Egle; Cumbo, Enzo; Cardoso, Rielson Jose A; Gallina, Giuseppe

    2012-01-01

    Adhesive dentistry is based on the development of materials which establish an effective bond with the tooth tissues. In this context, adhesive systems have attracted considerable research interest in recent years. Successful adhesive bonding depends on the chemistry of the adhesive, on appropriate clinical handling of the material as well as on the knowledge of the morphological changes caused on dental tissue by different bonding procedures. This paper outlines the status of contemporary adhesive systems, with particular emphasis on chemical characteristics and mode of interaction of the adhesives with enamel and dentinal tissues. Dental adhesives are used for several clinical applications and they can be classified based on the clinical regimen in "etch-and-rinse adhesives" and "self-etch adhesives". Other important considerations concern the different anatomical characteristics of enamel and dentine which are involved in the bonding procedures that have also implications for the technique used as well as for the quality of the bond. Etch-and-rinse adhesive systems generally perform better on enamel than self-etching systems which may be more suitable for bonding to dentine. In order to avoid a possible loss of the restoration, secondary caries or pulp damage due to bacteria penetration or due to cytotoxicity effects of eluted adhesive components, careful consideration of several factors is essential in selecting the suitable bonding procedure and adhesive system for the individual patient situation.

  13. Rapid pacing results in changes in atrial but not in ventricular refractoriness

    NARCIS (Netherlands)

    Schoonderwoerd, BA; Van Gelder, IC; Tieleman, RG; Bel, KJ; Crijns, HJGM

    It is well known that atrial tachycardia causes atrial electrical remodeling, characterized by shortening of atrial effective refractory periods (AERPs) and loss of physiological adaptation of AERP to rate. However, the nature and time course of changes in ventricular effective refractory periods

  14. Transient refractory material dissolution by a volumetrically-heated melt

    Energy Technology Data Exchange (ETDEWEB)

    Seiler, Jean Marie, E-mail: jean-marie.seiler@cea.fr [CEA, DEN, DTN, 17 Rue des Martyrs, 38054 Grenoble Cedex 9 (France); Ratel, Gilles [CEA, DEN, DTN, 17 Rue des Martyrs, 38054 Grenoble Cedex 9 (France); Combeau, Hervé [Institut Jean Lamour, UMR 7198, Lorraine University, Ecole des Mines de Nancy, Parc de Saurupt, 54042 Nancy Cedex (France); Gaus-Liu, Xiaoyang; Kretzschmar, Frank; Miassoedov, Alexei [Karlsruhe Institut of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany)

    2014-12-15

    Highlights: • We describe a test investigating ceramic dissolution by a molten non-eutectic melt. • The evolution of the interface temperature between melt and refractory is measured. • A theoretical model describing dissolution kinetics is proposed. • When dissolution stops, interface temperature is the liquidus temperature of the melt. - Abstract: The present work addresses the question of corium–ceramic interaction in a core catcher during a core-melt accident in a nuclear power plant. It provides an original insight into transient aspects concerning dissolution of refractory material by a volumetrically heated pool. An experiment with simulant material (LIVECERAM) is presented. Test results clearly show that dissolution of solid refractory material can occur in a non-eutectic melt at a temperature which is lower than the melting temperature of the refractory material. During the dissolution transient, the interface temperature rises above the liquidus temperature, corresponding to the instantaneous average composition of the melt pool. With constant power dissipation in the melt and external cooling of the core-catcher, a final steady-state situation is reached. Dissolution stops when the heat flux (delivered by the melt to the refractory) can be removed by conduction through the residual thickness of the ceramic, with T{sub interface} = T{sub liquidus} (calculated for the average composition of the final liquid pool). The final steady state corresponds to a uniform pool composition and uniform interface temperature distribution. Convection in the pool is governed by natural thermal convection and the heat flux distribution is therefore similar to what would be obtained for a single component pool. An interpretation of the experiment with two model-based approaches (0D and 1D) is presented. The mass transfer kinetics between the interface and the bulk is controlled by a diffusion sublayer within the boundary layer. During the dissolution transient

  15. Micromorphological characterization of adhesive interface of sound dentin and total-etch and self-etch adhesives.

    Science.gov (United States)

    Drobac, Milan; Stojanac, Igor; Ramić, Bojana; Premović, Milica; Petrović, Ljubomir

    2015-01-01

    The ultimate goal in restorative dentistry has always been to achieve strong and permanent bond between the dental tissues and filling materials. It is not easy to achieve this task because the bonding process is different for enamel and dentin-dentin is more humid and more organic than enamel. It is moisture and organic nature of dentin that make this hard tissue very complex to achieve adhesive bond. One of the first and most widely used tools for examining the adhesive bond between hard dental tissues and composite restorative materials is scanning electron microscopy. The aim of this study was scanning electron microscopy analyzes the interfacial micro morphology of total-etch and self-etch adhesives. Micro morphological characteristics of interface between total-etch adhesive (Prime & Bond NT) in combination with the corresponding composite (Ceram X Mono) were compared with those of self-etching adhesive (AdheSE One) in, combination with the corresponding composite (Tetric EvoCeram). The specimens were observed under 1000 x magnification of scanning electron microscopy (JEOL, JSM-6460 Low Vacuum). Measurement of the thickness of the hybrid layer of the examined com posite systems was performed with the software of the device used (NIH Image Analyser). Micromorphological analysis of interface showed that the hybrid layer in sound dentin was well formed, its average thickness being 2.68 microm, with a large number of resin tags and a large amount of lateral branches for specimens with a composite system Prime & Bond NT-Ceram X Mono. However, the specimens' with composite systems Adhese One-Tetric EvoCeram did not show the presence of hybrid layer and the resin tags were poorly represented. The results of this study suggest that total-etch adhesives bond better with sound dentin than self-etch adhesive.

  16. Effects of solvent evaporation time on immediate adhesive properties of universal adhesives to dentin.

    Science.gov (United States)

    Luque-Martinez, Issis V; Perdigão, Jorge; Muñoz, Miguel A; Sezinando, Ana; Reis, Alessandra; Loguercio, Alessandro D

    2014-10-01

    To evaluate the microtensile bond strengths (μTBS) and nanoleakage (NL) of three universal or multi-mode adhesives, applied with increasing solvent evaporation times. One-hundred and forty caries-free extracted third molars were divided into 20 groups for bond strength testing, according to three factors: (1) Adhesive - All-Bond Universal (ABU, Bisco, Inc.), Prime&Bond Elect (PBE, Dentsply), and Scotchbond Universal Adhesive (SBU, 3M ESPE); (2) Bonding strategy - self-etch (SE) or etch-and-rinse (ER); and (3) Adhesive solvent evaporation time - 5s, 15s, and 25s. Two extra groups were prepared with ABU because the respective manufacturer recommends a solvent evaporation time of 10s. After restorations were constructed, specimens were stored in water (37°C/24h). Resin-dentin beams (0.8mm(2)) were tested at 0.5mm/min (μTBS). For NL, forty extracted molars were randomly assigned to each of the 20 groups. Dentin disks were restored, immersed in ammoniacal silver nitrate, sectioned and processed for evaluation under a FESEM in backscattered mode. Data from μTBS were analyzed using two-way ANOVA (adhesive vs. drying time) for each strategy, and Tukey's test (α=0.05). NL data were computed with non-parametric tests (Kruskal-Wallis and Mann-Whitney tests, α=0.05). Increasing solvent evaporation time from 5s to 25s resulted in statistically higher mean μTBS for all adhesives when used in ER mode. Regarding NL, ER resulted in greater NL than SE for each of the evaporation times regardless of the adhesive used. A solvent evaporation time of 25s resulted in the lowest NL for SBU-ER. Residual water and/or solvent may compromise the performance of universal adhesives, which may be improved with extended evaporation times. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  17. Peritoneal adhesions after laparoscopic gastrointestinal surgery.

    Science.gov (United States)

    Mais, Valerio

    2014-05-07

    Although laparoscopy has the potential to reduce peritoneal trauma and post-operative peritoneal adhesion formation, only one randomized controlled trial and a few comparative retrospective clinical studies have addressed this issue. Laparoscopy reduces de novo adhesion formation but has no efficacy in reducing adhesion reformation after adhesiolysis. Moreover, several studies have suggested that the reduction of de novo post-operative adhesions does not seem to have a significant clinical impact. Experimental data in animal models have suggested that CO₂ pneumoperitoneum can cause acute peritoneal inflammation during laparoscopy depending on the insufflation pressure and the surgery duration. Broad peritoneal cavity protection by the insufflation of a low-temperature humidified gas mixture of CO₂, N₂O and O₂ seems to represent the best approach for reducing peritoneal inflammation due to pneumoperitoneum. However, these experimental data have not had a significant impact on the modification of laparoscopic instrumentation. In contrast, surgeons should train themselves to perform laparoscopy quickly, and they should complete their learning curves before testing chemical anti-adhesive agents and anti-adhesion barriers. Chemical anti-adhesive agents have the potential to exert broad peritoneal cavity protection against adhesion formation, but when these agents are used alone, the concentrations needed to prevent adhesions are too high and could cause major post-operative side effects. Anti-adhesion barriers have been used mainly in open surgery, but some clinical data from laparoscopic surgeries are already available. Sprays, gels, and fluid barriers are easier to apply in laparoscopic surgery than solid barriers. Results have been encouraging with solid barriers, spray barriers, and gel barriers, but they have been ambiguous with fluid barriers. Moreover, when barriers have been used alone, the maximum protection against adhesion formation has been no

  18. A randomized controlled trial of the ketogenic diet in refractory childhood epilepsy

    NARCIS (Netherlands)

    Lambrechts, D.A.J.E.; de Kinderen, R.J.A.; Vles, J.S.H.; de Louw, A.J.A.; Aldenkamp, A.P.; Majoie, H.J.M.

    2017-01-01

    Objective: To evaluate the efficacy and tolerability of the ketogenic diet (KD) during the first 4 months of a randomized controlled trial (RCT) in refractory epilepsy patients aged 1–18 years. Methods: Children and adolescents with refractory epilepsy, not eligible for epilepsy surgery, were

  19. Improved cooler design of electric arc furnace refractory in mining industry using thermal analysis modeling and simulation

    International Nuclear Information System (INIS)

    Istadi, I.; Bindar, Y.

    2014-01-01

    Production of steel and nickel using the electric arc furnace should be focused on the intensification of energy. Improvement of energy efficiency of the most consuming facilities was achieved by improving the use of alternative energy minimization such as reducing the heat lost of hot gases, minimizing the heat radiated through refractory linings of metallurgical furnaces, and cooling the highly thermally stressed components. The refractory of electric arc furnace should be modified to achieve the best cooling system of the furnace. In this physical modeling and simulation works, four modification scenarios of wall refractory designs were simulated, i.e. refractory with basic design, refractory with deep plate coolers, refractory with extra plate coolers, and refractory with wall falling film coolers. Finally, the use of deep plate cooler and the existing waffle cooler system was considered to be the best design of efficient electric arc furnace operationally. - Highlights: • Electric arc furnace design should be focused on the intensification of energy. • Refractory of electric arc furnace were modified to achieve the best cooling system. • Four modification scenarios of the wall refractory designs were simulated. • Use of deep plate cooler and existing waffle cooler system is the best cooling

  20. Ixabepilone: a new chemotherapeutic option for refractory metastatic breast cancer

    Directory of Open Access Journals (Sweden)

    Shannon Puhalla

    2008-09-01

    Full Text Available Shannon Puhalla, Adam BrufskyUPMC Magee-Womens Cancer Program, University of Pittsburgh, Pittsburgh, Pennsylvania, USAAbstract: Taxane therapy is commonly used in the treatment of metastatic breast cancer. However, most patients will eventually become refractory to these agents. Ixabepilone is a newly approved chemotherapeutic agent for the treatment of metastatic breast cancer. Although it targets microtubules similarly to docetaxel and paclitaxel, ixabepilone has activity in patients that are refractory to taxanes. This review summarizes the pharmacology of ixapebilone and clinical trials with the drug both as a single agent and in combination. Data were obtained using searches of PubMed and abstracts of the annual meetings of the American Society of Clinical Oncology and the San Antonio Breast Cancer Symposium from 1995 to 2008. Ixapebilone is a semi-synthetic analog of epothilone B that acts to induce apoptosis of cancer cells via the stabilization of microtubules. Phase I clinical trials have employed various dosing schedules ranging from daily to weekly to 3-weekly. Dose-limiting toxicites included neuropathy and neutropenia. Responses were seen in a variety of tumor types. Phase II studies verified activity in taxane-refractory metastatic breast cancer. The FDA has approved ixabepilone for use as monotherapy and in combination with capecitabine for the treatment of metastatic breast cancer. Ixabepilone is an efficacious option for patients with refractory metastatic breast cancer. The safety profile is similar to that of taxanes, with neuropathy and neutropenia being dose-limiting. Studies are ongoing with the use of both iv and oral formulations and in combination with other chemotherapeutic and biologic agents.Keywords: ixabepilone, epothilone, metastatic breast cancer, taxane-refractory

  1. Functionally Graded Adhesives for Composite Joints

    Science.gov (United States)

    Stapleton, Scott E.; Waas, Anthony M.; Arnold, Steven M.

    2012-01-01

    Adhesives with functionally graded material properties are being considered for use in adhesively bonded joints to reduce the peel stress concentrations located near adherend discontinuities. Several practical concerns impede the actual use of such adhesives. These include increased manufacturing complications, alterations to the grading due to adhesive flow during manufacturing, and whether changing the loading conditions significantly impact the effectiveness of the grading. An analytical study is conducted to address these three concerns. An enhanced joint finite element, which uses an analytical formulation to obtain exact shape functions, is used to model the joint. Furthermore, proof of concept testing is conducted to show the potential advantages of functionally graded adhesives. In this study, grading is achieved by strategically placing glass beads within the adhesive layer at different densities along the joint.

  2. Clinical outcomes of intravenous immunoglobulin therapy in refractory uveitis.

    Science.gov (United States)

    Garcia-Geremias, M; Carreño, E; Epps, S J; Lee, R W J; Dick, A D

    2015-04-01

    Intravenous immunoglobulin (IVIg) therapy has multiple mechanisms of immunomodulatory action. We wished therefore to assess its efficacy in a spectrum of patients with refractory uveitis. Retrospective review of clinical charts was conducted to document response to IVIg treatment in consecutive patients with treatment-refractory uveitis. Main outcome measures were control of intraocular inflammation, visual acuity, progression of the disease, and complications. Four (two male) patients, with a mean age at the beginning of the treatment of 47 years (range: 39-64), were included in the study. Indication for treatment was patients with active non-infectious uveitis refractory to steroids and immunomodulatory therapy. All patients received a course of 0.5 g/kg per day of IVIg for three consecutive days, repeating this course at a mean of 11 week (range: 2-39 weeks) intervals when indicated clinically. The median duration of the IVIg therapy was 7 months (range: 3-14 months). In three patients treatment resulted in stabilisation and prevention of progression of the disease, and additionally in two patients it facilitated a decrease in prednisolone dose. Treatment failed to induce long-term remission in one patient with recurrence of macular oedema. IVIg was well tolerated with neither immediate nor longer-term adverse events observed. In three out of four cases IVIg was an effective adjunctive therapy and well tolerated for the management of treatment-refractory uveitis.

  3. Adhesive bonding of wood materials

    Science.gov (United States)

    Charles B. Vick

    1999-01-01

    Adhesive bonding of wood components has played an essential role in the development and growth of the forest products industry and has been a key factor in the efficient utilization of our timber resource. The largest use of adhesives is in the construction industry. By far, the largest amounts of adhesives are used to manufacture building materials, such as plywood,...

  4. Wood Composite Adhesives

    Science.gov (United States)

    Gomez-Bueso, Jose; Haupt, Robert

    The global environment, in which phenolic resins are being used for wood composite manufacture, has changed significantly during the last decade. This chapter reviews trends that are driving the use and consumption of phenolic resins around the world. The review begins with recent data on volume usage and regional trends, followed by an analysis of factors affecting global markets. In a section on environmental factors, the impact of recent formaldehyde emission regulations is discussed. The section on economics introduces wood composite production as it relates to the available adhesive systems, with special emphasis on the technical requirement to improve phenolic reactivity. Advances in composite process technology are introduced, especially in regard to the increased demands the improvements place upon adhesive system performance. The specific requirements for the various wood composite families are considered in the context of adhesive performance needs. The results of research into current chemistries are discussed, with a review of recent findings regarding the mechanisms of phenolic condensation and acceleration. Also, the work regarding alternate natural materials, such as carbohydrates, lignins, tannins, and proteinaceous materials, is presented. Finally, new developments in alternative adhesive technologies are reported.

  5. Comparison of enamel bond fatigue durability between universal adhesives and two-step self-etch adhesives: Effect of phosphoric acid pre-etching.

    Science.gov (United States)

    Suda, Shunichi; Tsujimoto, Akimasa; Barkmeier, Wayne W; Nojiri, Kie; Nagura, Yuko; Takamizawa, Toshiki; Latta, Mark A; Miyazaki, Masashi

    2018-03-30

    The effect of phosphoric acid pre-etching on enamel bond fatigue durability of universal adhesives and two-step self-etch adhesives was investigated. Four universal adhesives and three two-step self-etch adhesives were used. The initial shear bond strengths and shear fatigue strengths to enamel with and without phosphoric acid pre-etching using the adhesives were determined. SEM observations were also conducted. Phosphoric acid pre-etching of enamel was found to increase the bond fatigue durability of universal adhesives, but its effect on two-step self-etch adhesives was material-dependent. In addition, some universal adhesives with phosphoric acid pre-etching showed similar bond fatigue durability to the two-step self-etch adhesives, although the bond fatigue durability of universal adhesives in self-etch mode was lower than that of the two-step self-etch adhesives. Phosphoric acid pre-etching enhances enamel bond fatigue durability of universal adhesives, but the effect of phosphoric acid pre-etching on the bond fatigue durability of two-step self-etch adhesives was material-dependent.

  6. Quantitative measurement of changes in adhesion force involving focal adhesion kinase during cell attachment, spread, and migration

    International Nuclear Information System (INIS)

    Wu, C.-C.; Su, H.-W.; Lee, C.-C.; Tang, M.-J.; Su, F.-C.

    2005-01-01

    Focal adhesion kinase (FAK) is a critical protein for the regulation of integrin-mediated cellular functions and it can enhance cell motility in Madin-Darby canine kidney (MDCK) cells by hepatocyte growth factor (HGF) induction. We utilized optical trapping and cytodetachment techniques to measure the adhesion force between pico-Newton and nano-Newton (nN) for quantitatively investigating the effects of FAK on adhesion force during initial binding (5 s), beginning of spreading (30 min), spreadout (12 h), and migration (induced by HGF) in MDCK cells with overexpressed FAK (FAK-WT), FAK-related non-kinase (FRNK), as well as normal control cells. Optical tweezers was used to measure the initial binding force between a trapped cell and glass coverslide or between a trapped bead and a seeded cell. In cytodetachment, the commercial atomic force microscope probe with an appropriate spring constant was used as a cyto-detacher to evaluate the change of adhesion force between different FAK expression levels of cells in spreading, spreadout, and migrating status. The results demonstrated that FAK-WT significantly increased the adhesion forces as compared to FRNK cells throughout all the different stages of cell adhesion. For cells in HGF-induced migration, the adhesion force decreased to almost the same level (∼600 nN) regardless of FAK levels indicating that FAK facilitates cells to undergo migration by reducing the adhesion force. Our results suggest FAK plays a role of enhancing cell adhesive ability in the binding and spreading, but an appropriate level of adhesion force is required for HGF-induced cell migration

  7. Advances in refractories for the metallurgical industries III: proceedings of the international symposium

    Energy Technology Data Exchange (ETDEWEB)

    Allaire, C.; Rigaud, M. [eds.] [Ecole Polytchnique, Montreal, PQ (Canada)

    1999-07-01

    In the three years since the last symposium key innovations have been made in the penetration of monoliths in all sectors of the metallurgical industries. The symposium was presented within the 38th Annual Conference of Metallurgists of the Canadian Institute of Mining, Metallurgy and Petroleum. Broad international coverage was maintained with papers originating from 12 different countries including: Australia, Canada, China, France, Germany, India, Iran, Japan, Korea, Mexico, New Zealand, Norway, and the United States. The 27 papers presented are divided into seven sessions to reflect the interests of the participants. The sessions included mold fluxes I and II, aluminum refractories, alumina castables, andalusite castables, continuous casting of refractories, aluminum refractories II and copper-nickel refineries. One paper on refractories for exhaust gas scrubbers is abstracted separately.

  8. Overview of Stirling Technology Research at NASA Glenn Research Center

    Science.gov (United States)

    Wilson, Scott D.; Schifer, Nicholas A.; Williams, Zachary D.; Metscher, Jonathan F.

    2016-01-01

    Stirling Radioisotope Power Systems (RPSs) are under development to provide power on future space science missions where robotic spacecraft will orbit, fly by, land, or rove using less than a quarter of the plutonium the currently available RPS uses to produce about the same power. NASA Glenn Research Center's newly formulated Stirling Cycle Technology Development Project (SCTDP) continues development of Stirling-based systems and subsystems, which include a flight-like generator and related housing assembly, controller, and convertors. The project also develops less mature technologies under Stirling Technology Research, with a focus on demonstration in representative environments to increase the technology readiness level (TRL). Matured technologies are evaluated for selection in future generator designs. Stirling Technology Research tasks focus on a wide variety of objectives, including increasing temperature capability to enable new environments, reducing generator mass and/or size, improving reliability and system fault tolerance, and developing alternative designs. The task objectives and status are summarized.

  9. Evaluation of refractory materials for a nuclear waste incinerator

    International Nuclear Information System (INIS)

    Grotzky, V.K.; Kneale, P.A.; Teter, A.R.

    1980-01-01

    An experiment to find a suitable refractory lining for a nuclear waste incinerator has been completed. Eleven brick and six castable products were analyzed by optical and scanning microscopy. All the materials were fashioned into cup shapes and subjected to temperatures ranging from 800 to 1200 0 C for as long as six weeks. Some of the cups were charged weekly with pellets made from ash materials that would contact an incinerator liner. Refractory products containing a high percentage of aluminum oxide had the greatest resistance to cracking and slag buildup. 35 figures

  10. Refractory status epilepticus and glutamic acid decarboxylase antibodies in adults: presentation, treatment and outcomes.

    Science.gov (United States)

    Khawaja, Ayaz M; Vines, Brannon L; Miller, David W; Szaflarski, Jerzy P; Amara, Amy W

    2016-03-01

    Glutamic acid decarboxylase antibodies (GAD-Abs) have been implicated in refractory epilepsy. The association with refractory status epilepticus in adults has been rarely described. We discuss our experience in managing three adult patients who presented with refractory status epilepticus associated with GAD-Abs. Case series with retrospective chart and literature review. Three patients without pre-existing epilepsy who presented to our institution with generalized seizures between 2013 and 2014 were identified. Seizures proved refractory to first and second-line therapies and persisted beyond 24 hours. Patient 1 was a 22-year-old female who had elevated serum GAD-Ab titres at 0.49 mmol/l (normal: status epilepticus. Causation cannot be established since GAD-Abs may be elevated secondary to concurrent autoimmune diseases or formed de novo in response to GAD antigen exposure by neuronal injury. Based on this report and available literature, there may be a role for immuno- and chemotherapy in the management of refractory status epilepticus associated with GAD-Abs.

  11. Fibrillar Adhesive for Climbing Robots

    Science.gov (United States)

    Pamess, Aaron; White, Victor E.

    2013-01-01

    A climbing robot needs to use its adhesive patches over and over again as it scales a slope. Replacing the adhesive at each step is generally impractical. If the adhesive or attachment mechanism cannot be used repeatedly, then the robot must carry an extra load of this adhesive to apply a fresh layer with each move. Common failure modes include tearing, contamination by dirt, plastic deformation of fibers, and damage from loading/ unloading. A gecko-like fibrillar adhesive has been developed that has been shown useful for climbing robots, and may later prove useful for grasping, anchoring, and medical applications. The material consists of a hierarchical fibrillar structure that currently contains two levels, but may be extended to three or four levels in continuing work. The contacting level has tens of thousands of microscopic fibers made from a rubberlike material that bend over and create intimate contact with a surface to achieve maximum van der Waals forces. By maximizing the real area of contact that these fibers make and minimizing the bending energy necessary to achieve that contact, the net amount of adhesion has been improved dramatically.

  12. Age Increases Monocyte Adhesion on Collagen

    Science.gov (United States)

    Khalaji, Samira; Zondler, Lisa; Kleinjan, Fenneke; Nolte, Ulla; Mulaw, Medhanie A.; Danzer, Karin M.; Weishaupt, Jochen H.; Gottschalk, Kay-E.

    2017-05-01

    Adhesion of monocytes to micro-injuries on arterial walls is an important early step in the occurrence and development of degenerative atherosclerotic lesions. At these injuries, collagen is exposed to the blood stream. We are interested whether age influences monocyte adhesion to collagen under flow, and hence influences the susceptibility to arteriosclerotic lesions. Therefore, we studied adhesion and rolling of human peripheral blood monocytes from old and young individuals on collagen type I coated surface under shear flow. We find that firm adhesion of monocytes to collagen type I is elevated in old individuals. Pre-stimulation by lipopolysaccharide increases the firm adhesion of monocytes homogeneously in older individuals, but heterogeneously in young individuals. Blocking integrin αx showed that adhesion of monocytes to collagen type I is specific to the main collagen binding integrin αxβ2. Surprisingly, we find no significant age-dependent difference in gene expression of integrin αx or integrin β2. However, if all integrins are activated from the outside, no differences exist between the age groups. Altered integrin activation therefore causes the increased adhesion. Our results show that the basal increase in integrin activation in monocytes from old individuals increases monocyte adhesion to collagen and therefore the risk for arteriosclerotic plaques.

  13. Adhesion of Zinc Hot-dip Coatings

    Directory of Open Access Journals (Sweden)

    Michal Černý

    2014-01-01

    Full Text Available The work is focused on verification of quality adhesion of zinc coating. It describes elements which affect quality and adhesive solidity within the coating. For assessment itself it will be neccessary to get know the basic elements which can affect adhesion of hot-dip coating which will be essential for choosing suitable samples for verification itself. These elements characterise acoustic responses during delamination coating. They affect elements influencing progress of signal. In research there is also a summary of existing methods for testing adhesion of coatings. As a result a new proposal of a new method comes out for purpose of quality testing of adhesion zinc hot-dip coating. The results of verification of this method are put to scientific analysis and findings lead to assessment of proposed method and its application in technical practise.The goal of this contribution is also include to proposed methodology testing adhesion zinc coating by nondestructive diagnostic method of acoustic emission (AE, which would monitor characterise progress of coating delamination of hot-dip zinc from basic material in way to adhesion tests would be practicable in situ. It can be enabled by analysis and assessment of results acquired by method AE and its application within verification of new method of adhesion anti-corrosive zinc coating.

  14. Free-Piston Stirling Convertor Controller Development at NASA Glenn Research Center

    Science.gov (United States)

    Regan, Timothy

    2004-01-01

    The free-piston Stirling convertor end-to-end modeling effort at NASA Glenn Research Center (GRC) has produced a software-based test bed in which free-piston Stirling convertors can be simulated and evaluated. The simulation model includes all the components of the convertor - the Stirling cycle engine, linear alternator, controller, and load. This paper is concerned with controllers. It discusses three controllers that have been studied using this model. Case motion has been added to the model recently so that effects of differences between convertor components can be simulated and ameliorative control engineering techniques can be developed. One concern when applying a system comprised of interconnected mass-spring-damper components is to prevent operation in any but the intended mode. The design mode is the only desired mode of operation, but all other modes are considered in controller design.

  15. Evaluation of olivine refractories for TES

    Science.gov (United States)

    Gay, B. M.; Cochrane, R. L.; Palmour, H., III; Paisley, M. J.

    1982-02-01

    The principal objectives of this program are to (1) experimentally determine the degree of improvement in thermal and mechanical performance that can be obtained with an olivine thermal storage brick made of domestic materials using advanced processing techniques compared with state-of-the-art as represented by commercial European bricks, (2) conduct an assessment of existing German ceramic process technology and determine its adaptability to domestic raw materials and manufacturing practices, and (3) investigate, on a limited basis, method for further improvement of domestic-olivine brick. To date, accomplishments include (1) installation of improved, computer-based instrumentation, (2) the use of this system to determine performance characteristics of a set of heat storage refractories under cyclic use conditions, (3) acquisition of the services of a knowledgeable European consultant, (4) continued lab-scale process/property optimization studies, and (5) comparative testing of olivine-based and magnesite-based heat storage refractories in the calorimetric test facility at Purdue University.

  16. An unusual case of refractory wheeze

    Science.gov (United States)

    Ramesh, Venkat; Acharya, Vishak; Pai, Narasimha; Krishnan, Ananda

    2015-01-01

    A 37-year-old man presented with a history of episodic wheeze and breathlessness of 3 years’ duration refractory to treatment. Physical examination revealed diffuse expiratory polyphonic rhonchi while the remainder of the examination including the cardiac examination was reported as normal. Pulmonary function testing revealed mild obstruction with bronchodilator reversibility. The patient was discharged on a 6-month course of antitubercular treatment (ATT) as bronchial brush cytology (obtained via bronchoscopy) was positive for acid-fast bacilli. The patient presented after completing 6 months of ATT with persistent symptoms, a loud S1 and a mid-diastolic murmur at the apex. High-resolution CT of the chest showed bilateral dependent ground glass opacities. An echocardiogram revealed a left atrial myxoma, and normal RV size and pressures. The patient underwent successful surgical removal of the same, and made a complete recovery. Refractory wheeze is a very unusual presentation of a left atrial myxoma. PMID:25733086

  17. Preparation and characterization of clay bonded high strength silica refractory by utilizing agriculture waste

    International Nuclear Information System (INIS)

    Bhardwaj, A.; Hossain, S.K.S.; Majh, M.R.

    2017-01-01

    Clay bonded silica refractory was prepared by utilizing agriculture waste called rice husk ash (RHA) and refractory grog. Various samples were prepared with different compositions based upon partial replacement of quartz by RHA. Rectangular samples were prepared by following semi dry process prior to pressing in a uniaxial hydraulic press and sintering at a temperature of 1200°C in air atmosphere. Various physical, mechanical and thermal characterizations were done like X-ray diffraction (XRD), scanning electron microscope (SEM), apparent porosity (AP), bulk density (BD), cold crushing strength (CCS), refractoriness and thermal conductivity measurement. The sample utilizing 30% of RHA was considered most optimum composition which produced cold crushing strength of 38MPa and thermal conductivity of 2.08W/mK at 800°C with a considerable good refractoriness. Enhancement in the mechanical as well as thermal properties may be considered as attributed to the amorphous silica which has reacted more easily and efficiently with other material surrounding giving rise to the densification and produced stable crystalline phase to the refractory material. These promising characteristics suggests that the RHA may lead to be used as a potential material for the preparation of clay bonded high strength silica refractories. [es

  18. Enhancement of the life of refractories through the operational experience of plasma torch melter

    Energy Technology Data Exchange (ETDEWEB)

    Moon, Young Pyo [Technology Institute, Korea Radioactive waste Agency (KORAD), Daejeon (Korea, Republic of); Choi, Jaang Young [Chungnam National University, Daejeon (Korea, Republic of)

    2016-06-15

    The properties of wastes for melting need to be considered to minimize the maintenance of refractory and to discharge the molten slags smoothly from a plasma torch melter. When the nonflammable wastes from nuclear facilities such as concrete debris, glass, sand, etc., are melted, they become acid slags with low basicity since the chemical composition has much more acid oxides than basic oxides. A molten slag does not have good characteristics of discharge and is mainly responsible for the refractory erosion due to its low liquidity. In case of a stationary plasma torch melter with a slant tapping port on the wall, a fixed amount of molten slags remains inside of tapping hole as well as the melter inside after tapping out. Nonmetallic slags keep the temperature higher than melting point of metal because metallic slags located on the bottom of melter by specific gravity difference are simultaneously melted when dual mode plasma torch operates in transferred mode. In order to minimize the refractory erosion, the compatible refractories are selected considering the temperature inside the melter and the melting behavior of slags whether to contact or noncontact with molten slags. An acidic refractory shall not be installed in adjacent to a basic refractory for the resistibility against corrosion.

  19. Refractory heartburn: comparison of intercellular space diameter in documented GERD vs. functional heartburn.

    Science.gov (United States)

    Vela, Marcelo F; Craft, Brandon M; Sharma, Neeraj; Freeman, Janice; Hazen-Martin, Debra

    2011-05-01

    Refractory heartburn despite acid suppression may be explained by ongoing gastroesophageal reflux disease (GERD) or functional heartburn (FH), i.e., symptoms without evidence of GERD. Impedance-pH monitoring (impedance-pH) detects acid and nonacid reflux and is useful for evaluating acid-suppressed, refractory patients. Intercellular space diameter (ISD) of esophageal epithelium measured by transmission electron microscopy (TEM) is a marker of epithelial damage present in both erosive and nonerosive reflux disease. ISD has not been used to study refractory heartburn or FH. Our aim was to compare ISD in healthy controls and refractory heartburn patients with GERD and FH. In refractory heartburn patients (heartburn more than twice/week for at least 2 months despite proton pump inhibitor (PPI) b.i.d.), erosive esophagitis and/or abnormal impedance-pH (increased acid exposure or positive symptom index) defined GERD; normal esophagogastroduodenoscopy (EGD)/impedance-pH defined FH. Asymptomatic, healthy controls had normal EGD and pH-metry. Mean ISD in each subject, determined by blinded TEM of esophageal biopsies, was the average of 100 measurements (10 measurements in each of 10 micrographs). In all, 11 healthy controls, 11 FH, and 15 GERD patients were studied. Mean ISD was significantly higher in GERD compared with controls (0.87 vs. 0.32 μm, P=0.003) and FH (0.87 vs. 0.42 μm, P=0.012). Mean ISD was similar in FH and controls (0.42 vs. 0.32 μm, P=0.1). The proportion of patients with abnormal ISD was significantly higher for GERD compared with FH (60 vs. 9%, P=0.014). ISD is increased in refractory heartburn patients with GERD but not those with FH. Our findings suggest that measurement of ISD by TEM might be a useful tool to distinguish GERD from FH in patients with refractory heartburn.

  20. EB curable laminating adhesives

    International Nuclear Information System (INIS)

    Matsuyama, Asao; Kobayashi, Masahide; Gotoh, Sakiko

    1992-01-01

    New developed solvent free EB curable laminating adhesives have two liquid components, A with hydroxy and acryloyl group, B with isocyanate and acryloyl group in a molecule. These EB laminating adhesives do not need any aging process, which is a big advantage, and are very suitable for environment, safety, and health because of no heating process and solvent free formulas. And we have made basic research about the relation of peel strength or heat seal strength versus Tg of cured film, elongation at break, elastic modulus, and so on. Basic specifications of the new developed adhesives are shown. (author)

  1. Platelet adhesiveness: the effect of centrifugation on the measurement of adhesiveness in platelet-rich plasma

    Science.gov (United States)

    McBride, J. A.

    1968-01-01

    Platelet adhesiveness has been measured in citrated whole blood and in platelet-rich plasma obtained from normal subjects, splenectomized patients, and from patients in whom the diagnosis of recurrent venous thrombosis had been made. The duration of centrifugation used in the preparation of platelet-rich plasma was found to have a profound effect on the measurement of platelet adhesiveness because the figure for platelet adhesiveness measured in platelet-rich plasma obtained by centrifugation was considerably lower than that found in citrated whole blood. This effect was particularly marked when platelet-rich plasma was obtained from subjects in whom platelet adhesiveness measured in whole blood was increased. PMID:5699080

  2. Adhesive Joints in Wind Turbine Blades

    DEFF Research Database (Denmark)

    Jørgensen, Jeppe Bjørn

    to be determined in several different ways. The accuracy of different ways of measuring residual stresses in the adhesive was tested by applying five different methods on a single sandwich test specimen (laminate/adhesive/laminate) that was instrumented with strain gauges and fiber Bragg gratings. Quasi...... of the project is to develop new- and to improve the existing design rules for adhesive joints in wind turbine blades. The first scientific studies of adhesive joints were based on stress analysis, which requires that the bond-line is free of defects, but this is rarely the case for a wind turbine blade. Instead...... curing and test temperatures) on the formation of transverse cracks in the adhesive were tested experimentally. It was assumed that the transverse cracks evolved due to a combination of mechanical- and residual stresses in the adhesive. A new approach was developed that allows the residual stress...

  3. Influence of Conditioning Time of Universal Adhesives on Adhesive Properties and Enamel-Etching Pattern.

    Science.gov (United States)

    Cardenas, A M; Siqueira, F; Rocha, J; Szesz, A L; Anwar, M; El-Askary, F; Reis, A; Loguercio, A

    2016-01-01

    To evaluate the effect of application protocol in resin-enamel microshear bond strength (μSBS), in situ degree of conversion, and etching pattern of three universal adhesive systems. Sixty-three extracted third molars were sectioned in four parts (buccal, lingual, and proximals) and divided into nine groups, according to the combination of the main factors-Adhesive (Clearfil Universal, Kuraray Noritake Dental Inc, Tokyo, Japan; Futurabond U, VOCO, Cuxhaven, Germany; and Scotchbond Universal Adhesive, 3M ESPE, St Paul, MN, USA)-and enamel treatment/application time (etch-and-rinse mode [ER], self-etch [SE] application for 20 seconds [SE20], and SE application for 40 seconds [SE40]). Specimens were stored in water (37°C/24 h) and tested at 1.0 mm/min (μSBS). The degree of conversion of the adhesives at the resin-enamel interfaces was evaluated using micro-Raman spectroscopy. The enamel-etching pattern was evaluated under a scanning electron microscope. Data were analyzed with two-way analysis of variance and Tukey test (α=0.05). In general, the application of the universal adhesives in the SE40 produced μSBS and degree of conversion that were higher than in the SE20 (puniversal adhesives in the SE mode may be a viable alternative to increase the degree of conversion, etching pattern, and resin-enamel bond strength.

  4. 21 CFR 175.125 - Pressure-sensitive adhesives.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Pressure-sensitive adhesives. 175.125 Section 175...) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: ADHESIVES AND COMPONENTS OF COATINGS Substances for Use Only as Components of Adhesives § 175.125 Pressure-sensitive adhesives. Pressure-sensitive...

  5. AN ANALYTICAL STUDY IN ADHESIVE BOWEL OBSTRUCTION

    Directory of Open Access Journals (Sweden)

    Gerald Anand Raja

    2017-04-01

    Full Text Available BACKGROUND Peritoneal adhesions can be defined as abnormal fibrous bands between organs or tissues or both in the abdominal cavity that are normally separated. Adhesions may be acquired or congenital; however, most are acquired as a result of peritoneal injury, the most common cause of which is abdominopelvic surgery. Less commonly, adhesions may form as the result of inflammatory conditions, intraperitoneal infection or abdominal trauma. The extent of adhesion formation varies from one patient to another and is most dependent on the type and magnitude of surgery performed as well as whether any postoperative complications develop. Fortunately, most patients with adhesions do not experience any overt clinical symptoms. For others, adhesions may lead to any one of a host of problems and can be the cause of significant morbidity and mortality. MATERIALS AND METHODS This is a retrospective study of 50 patients admitted in Government Royapettah Hospital with adhesive bowel obstruction between September 2008 to September 2010. All patients were admitted and managed either conservatively or surgically. RESULTS 1. Adhesive bowel disease is the most common cause for bowel obstruction followed by hernias. 2. Increased incidence is noted in females. 3. Increased incidence of adhesions was documented in gynaecological and colorectal surgeries. 4. Below umbilical incisions have higher propensity for adhesion formation. 5. Laparotomies done for infective aetiology have higher adhesion risks. 6. Most of adhesive obstructions can be managed conservatively. 7. Adhesiolysis preferably laparoscopic can be done. For gangrenous bowel resection and anastomosis or ostomy done. 8. Given the above risk factors, adhesive bowel disease can be prevented to a certain extent. CONCLUSION The formation of peritoneal adhesions continues to plague patients, surgeons and society. Although, research in this area is ongoing, there is currently no method that is 100% effective in

  6. Disorders of adhesions or adhesion-related disorder: monolithic entities or part of something bigger--CAPPS?

    Science.gov (United States)

    Wiseman, David M

    2008-07-01

    The purpose of this article is to review progress in the field of abdominopelvic adhesions and the validity of its two underlying assumptions: (1) The formation of adhesions results in infertility, bowel obstruction, or other complications. Reducing or avoiding adhesions will curb these sequelae. (2) "Adhesions" is a monolithic entity to be tackled without regard to any other condition. Evidence is discussed to validate the first assumption. We reviewed progress in the field by examining hospital data. We found a growing trend in the number and cost of discharges for just two adhesion-related diagnoses, and the low usage of adhesion barriers appears in at most 5% of appropriate procedures. Data from an Internet-based survey suggested that the problem may be partly due to ignorance among patients and physicians about adhesions and their prevention. Two other surveys of patients visiting the adhesions.org Web site defined more fully adhesion-related disorder (ARD). The first survey ( N = 466) described a patient with chronic pain, gastrointestinal disturbances, an average of nine bowel obstructions, and an inability to work or maintain family or social relationships. The second survey (687 U.S. women) found a high (co-) prevalence of abdominal or pelvic adhesions (85%), chronic abdominal or pelvic pain (69%), irritable bowel syndrome (55%), recurrent bowel obstruction (44%), endometriosis (40%), and interstitial cystitis (29%). This pattern suggests that although "adhesions" may start out as a monolithic entity, an adhesions patient may develop related conditions (ARD) until they merge into an independent entity where they are practically indistinguishable from patients with multiple symptoms originating from other abdominopelvic conditions such as pelvic or bladder pain. Rather than use terms that constrain the required multidisciplinary, biopsychosocial approach to these patients by the paradigms of the specialty related to the patient's initial symptom set, the

  7. Colectomy for refractory constipation

    DEFF Research Database (Denmark)

    Raahave, Dennis; Loud, Franck Bjørn; Christensen, Elsebeth

    2010-01-01

    OBJECTIVE: This study evaluated the type of colectomy, postoperative complications, functional results, and satisfaction in patients with constipation refractory to conservative therapy. Further, colonic transit time (CTT), faecal load (coprostasis), and colon length (redundancies) were compared...... had at hemicolectomy, 11 patients a subtotal colectomy and 3 patients an ileostomy. Two patients had an anastomotic leak and one died. In 11 patients, further surgery was necessary, because of recurrent constipation. Abdominal pain disappeared and defecation patterns improved significantly to 1-4 per...

  8. Refractory alloy component fabrication

    International Nuclear Information System (INIS)

    Young, W.R.

    1984-01-01

    Purpose of this report is to describe joining procedures, primarily welding techniques, which were developed to construct reliable refractory alloy components and systems for advanced space power systems. Two systems, the Nb-1Zr Brayton Cycle Heat Receiver and the T-111 Alloy Potassium Boiler Development Program, are used to illustrate typical systems and components. Particular emphasis is given to specific problems which were eliminated during the development efforts. Finally, some thoughts on application of more recent joining technology are presented. 78 figures

  9. Effect of a low-viscosity adhesive resin on the adhesion of metal brackets to enamel etched with hydrochloric or phosphoric acid combined with conventional adhesives.

    Science.gov (United States)

    Yetkiner, Enver; Ozcan, Mutlu; Wegehaupt, Florian Just; Wiegand, Annette; Eden, Ece; Attin, Thomas

    2013-12-01

    This study investigated the effect of a low-viscosity adhesive resin (Icon) applied after either hydrochloric (HCl) or phosphoric acid (H3PO4) on the adhesion of metal brackets to enamel. Failure types were analyzed. The crowns of bovine incisors (N = 20) were sectioned mesio-distally and inciso-gingivally, then randomly assigned to 4 groups according to the following protocols to receive mandibular incisor brackets: 1) H3PO4 (37%)+TransbondXT (3M UNITEK); 2) H3PO4 (37%)+Icon+TransbondXT; 3) HCl (15%)+Icon (DMG)+TransbondXT 4) HCl (15%)+Icon+Heliobond (Ivoclar Vivadent)+TransbondXT. Specimens were stored in distilled water at 37°C for 24 h and thermocycled (5000x, 5°C to 55°C). The shear bond strength (SBS) test was performed using a universal testing machine (1 mm/min). Failure types were classified according to the Adhesive Remnant Index (ARI). Contact angles of adhesive resins were measured (n = 5 per adhesive) on ceramic surfaces. No significant difference in SBS was observed, implying no difference between combinations of adhesive resins and etching agents (p = 0.712; ANOVA). The Weibull distribution presented significantly lower Weibull modulus (m) of group 3 (m = 2.97) compared to other groups (m = 5.2 to 6.6) (p group 1 (45.4 ± 7.9) > group 2 (44.2 ± 10.6) > group 3 (42.6 ± 15.5). While in groups 1, 3, and 4 exclusively an ARI score of 0 (no adhesive left on tooth) was observed, in group 2, only one specimen demonstrated score 1 (less than half of adhesive left on tooth). Contact angle measurements were as follows: Icon (25.86 ± 3.81 degrees), Heliobond (31.98 ± 3.17 degrees), TransbondXT (35 ± 2.21 degrees). Icon can be safely used with the conventional adhesives tested on surfaces etched with either HCl or H3PO4.

  10. Aspirin augments hyaluronidase induced adhesion inhibition ...

    African Journals Online (AJOL)

    Postoperative adhesions occur after virtually all abdomino-pelvic surgery and are the leading cause of intestinal obstruction and other gynaecologic problems. We used an animal model to test the efficacy of combined administration of aspirin and hyaluronidase on adhesion formation. Adhesions were induced using ...

  11. Overview of Iodine Propellant Hall Thruster Development Activities at NASA Glenn Research Center

    Science.gov (United States)

    Kamhawi, Hani; Benavides, Gabriel; Haag, Thomas; Hickman, Tyler; Smith, Timothy; Williams, George; Myers, James; Polzin, Kurt; Dankanich, John; Byrne, Larry; hide

    2016-01-01

    NASA is continuing to invest in advancing Hall thruster technologies for implementation in commercial and government missions. There have been several recent iodine Hall propulsion system development activities performed by the team of the NASA Glenn Research Center, the NASA Marshall Space Flight Center, and Busek Co. Inc. In particular, the work focused on qualification of the Busek BHT-200-I, 200 W and the continued development of the BHT-600-I Hall thruster propulsion systems. This presentation presents an overview of these development activities and also reports on the results of short duration tests that were performed on the engineering model BHT-200-I and the development model BHT-600-I Hall thrusters.

  12. Method for hot pressing irregularly shaped refractory articles

    Science.gov (United States)

    Steinkamp, William E.; Ballard, Ambrose H.

    1982-01-01

    The present invention is directed to a method for hot pressing irregularly haped refractory articles with these articles of varying thickness being provided with high uniform density and dimensional accuracy. Two partially pressed compacts of the refractory material are placed in a die cavity between displaceable die punches having compact-contacting surfaces of the desired article configuration. A floating, rotatable block is disposed between the compacts. The displacement of the die punches towards one another causes the block to rotate about an axis normal to the direction of movement of the die punches to uniformly distribute the pressure loading upon the compacts for maintaining substantially equal volume displacement of the powder material during the hot pressing operation.

  13. Ketogenic Diet in Super-Refractory Status Epilepticus

    OpenAIRE

    Smith, Garnett; Press, Craig A.

    2017-01-01

    Researchers from the Children’s National Health System in Washington, D.C. studied the feasibility, rate of complications, and effect on seizures of initiating the Ketogenic Diet (KD) in pediatric patients with Super-Refractory Status Epilepticus (SRSE).

  14. Adhesion and adhesion changes at the copper metal-(acrylonitrile-butadiene-styrene) polymer interface

    NARCIS (Netherlands)

    Kisin, S.; Varst, van der P.G.T.; With, de G.

    2007-01-01

    It is known that the adhesive strength of metallic films on polymer substrates often changes in the course of time. To study this effect in more detail, the adhesion energy of sputtered and galvanically strengthened copper coatings on acrylonitrile–butadiene–styrene polymer substrate was determined

  15. Epoxy-resin adhesive and method for bonding using such an epoxy resin adhesive

    NARCIS (Netherlands)

    Bhowmik, S.; Poulis, J.A.; Benedictus, R.

    2008-01-01

    The invention relates to an epoxy resin adhesive comprising a dotation of nano-substances, wherein the nano- substances are selected from the group comprising carbon-fibre nanotubes, carbon nano-fibres, silicate nano powders, and wherein the nano-substances are dispersed in the adhesive with a

  16. Adhesion of Pharmaceutical Binding Agents I-Adhesion to polymeric materials

    Directory of Open Access Journals (Sweden)

    Hossain Orafai

    1996-08-01

    Full Text Available Adhesion of three commonly used pharmaceutical binding agents, HPMC , PVP and Gelatin to five different polymeric sheet materials was studied. After conditioning, the bond strength of the specimens were measured by shear testing method using a suitablely designed apparatus. The results were correlated to the surface energies and the solubiiity parameters of the adherends. It is concluded that the thermodynamic properties and the solubility parameters are dominant when the mechanisms of adhesion are by adsorption and diffusion respectively.

  17. Normally Oriented Adhesion versus Friction Forces in Bacterial Adhesion to Polymer-Brush Functionalized Surfaces Under Fluid Flow

    NARCIS (Netherlands)

    Swartjes, Jan J. T. M.; Veeregowda, Deepak H.; van der Mei, Henny C.; Busscher, Henk J.; Sharma, Prashant K.

    2014-01-01

    Bacterial adhesion is problematic in many diverse applications. Coatings of hydrophilic polymer chains in a brush configuration reduce bacterial adhesion by orders of magnitude, but not to zero. Here, the mechanism by which polymer-brush functionalized surfaces reduce bacterial adhesion from a

  18. an Adhesive Patch

    Directory of Open Access Journals (Sweden)

    S. Mojtaba Taghizadeh

    2013-01-01

    Full Text Available Drug-in-adhesive transdermal drug delivery systems  TDDSs containing stimulants, termed as energetic substances, such as caffeine and pantothenic acid, were studied. Caffeine is a white crystalline substance and a stimulant to central nervous system. In humans, caffeine acts as a central nervous system stimulant, temporarily warding off drowsiness and restoring alertness. Pantothenic acid, also recognized as vitamin B5, is a water-soluble vitamin. For many animals, pantothenic acid is an essential nutrient. Animals require pantothenic acid to synthesize and metabolize proteins, carbohydrates and fats. For this purpose caffeine and pantothenic acid were  used  as  drug  components with  6.32%  and  1.12%  loadings,  in  different functional and non-functional acrylic pressure sensitive adhesives (PSAs of 52.89%, respectively. Ethylene glycol as a chemical enhancer was used in all TDDSs with 39.67%. The effect of PSAs  type on  in vitro  release and adhesion properties  (peel strength and tack values from drug delivery devices were evaluated. It was found that TDDS containing -COOH functional PSA showed  the  lowest steady state fux. The adhesion properties of the samples were improved by addition of functional acrylic PSA in formulations.

  19. Clinical and etiological profile of refractory rickets from western India.

    Science.gov (United States)

    Joshi, Rajesh R; Patil, Shailesh; Rao, Sudha

    2013-07-01

    To present clinical and etiological profile of refractory rickets from Mumbai. Case records of 36 patients presenting over 2½ y with refractory rickets were evaluated with respect to clinical presentation, biochemical, radiological features and where needed, ophthalmological examination, ultrasonography and special tests on blood and urine. Twenty three (63 %) patients had renal tubular acidosis (RTA)-distal RTA in 20 and proximal RTA in 3 patients; 5 (14 %) had vitamin D dependent rickets (VDDR I in 2 and VDDR II in 3 patients), 4 (11 %) had chronic renal failure (CRF) and 2 each (6 %) had hypophosphatemic rickets and chronic liver disease as cause of refractory rickets. A significant proportion of patients with RTA and VDDR showed skeletal changes of rickets in the first 2 y of life, while those with hypophosphatemic rickets presented later. Patients with hypophosphatemic rickets had predominant involvement of lower limbs, normal blood calcium and PTH levels and phosphorus leak in urine. All patients with RTA presented with failure to thrive, polyuria and marked rickets; blood alkaline phosphatase levels being normal in almost 50 % patients. Three (75 %) patients with rickets due to CRF had GFR rickets inspite of taking high dose of vitamin D orally. Refractory rickets is a disorder of multiple etiologies; a good history and clinical examination supplemented with appropriate investigations helps to determine its cause.

  20. USE OF STRUCTURAL MRI IN PATIENTS WITH MEDICALLY REFRACTORY SEIZURES

    Directory of Open Access Journals (Sweden)

    Ara G. Kaprelyan

    2012-12-01

    Full Text Available Introduction: Refractory epilepsy is common in patients with structural brain lesions including acquired disorders and genetic abnormalities. Recently, MRI is a precise diagnostic tool for recognition of different structural causes underlying medically intractable seizures.Objective: To evaluate the usefulness of MRI for detection of brain lesions associated with refractory epilepsy.Material and methods: 49 patients (20M and 29F; aged 48.6±24.7 years with refractory epilepsy were included in the study. They presented with partial (46.0%, secondary (31.0% or primary (23.0% generalized tonic-clonic seizures. Clinical diagnosis was based on the revised criteria of ILAE. Structural neuroimaging (MRI, EEG recording, and neurological examination were performed.Results: MRI detected different structural brain abnormalities totally in 36 (73.5% patients, including cerebral tumors (21p, cerebrovascular accidents (5p, hyppocampal sclerosis (3p, developmental malformations (2p, postencephalitic lesions (2p, arachnoid cysts (2p, and tuberous sclerosis (1p. Neuroimaging revealed normal findings in 13 (27.5% cases. EEG recordings showed focal epileptic activity in 38 (77.6% patients, including 33 cases with and 5 without structural brain abnormalities.Conclusion: This study revealed that structural brain lesions are commonly associated with refractory epilepsy. We suggested that MRI is a useful diagnostic method for assessment of patients with uncontrolled seizures or altered epileptic pattern.

  1. Penetration and Effectiveness of Micronized Copper in Refractory Wood Species.

    Science.gov (United States)

    Civardi, Chiara; Van den Bulcke, Jan; Schubert, Mark; Michel, Elisabeth; Butron, Maria Isabel; Boone, Matthieu N; Dierick, Manuel; Van Acker, Joris; Wick, Peter; Schwarze, Francis W M R

    2016-01-01

    The North American wood decking market mostly relies on easily treatable Southern yellow pine (SYP), which is being impregnated with micronized copper (MC) wood preservatives since 2006. These formulations are composed of copper (Cu) carbonate particles (CuCO3·Cu(OH)2), with sizes ranging from 1 nm to 250 μm, according to manufacturers. MC-treated SYP wood is protected against decay by solubilized Cu2+ ions and unreacted CuCO3·Cu(OH)2 particles that successively release Cu2+ ions (reservoir effect). The wood species used for the European wood decking market differ from the North American SYP. One of the most common species is Norway spruce wood, which is poorly treatable i.e. refractory due to the anatomical properties, like pore size and structure, and chemical composition, like pit membrane components or presence of wood extractives. Therefore, MC formulations may not suitable for refractory wood species common in the European market, despite their good performance in SYP. We evaluated the penetration effectiveness of MC azole (MCA) in easily treatable Scots pine and in refractory Norway spruce wood. We assessed the effectiveness against the Cu-tolerant wood-destroying fungus Rhodonia placenta. Our findings show that MCA cannot easily penetrate refractory wood species and could not confirm the presence of a reservoir effect.

  2. Wettability between TiN,TiC Containing Carbon Composite Refractory and Molten Slag or Hot Metal

    Institute of Scientific and Technical Information of China (English)

    SHIYue-xun; LIYingand; 等

    1994-01-01

    In order to develop a new-type TiC-TiN containing carbon composite refractory so as to improve the service life of blast furnace hearth,the wettability between the carbon refractory and molten slag or metal has been mea-sured.It was indicated that the carbon refractory is wet-ted by slag(θ≤90°) when(TiC+TiN)>33.52%,The effects of TiN or TiC on wetting behavior are basi-cally identical.When the amount of TiC in the carbon com-posite refractory is greater than 60% it will be wetted by hot metal;therefore,the carbon composite refractory will be wetted by slag but not permeated by hot metal when the amount of TiC is restricted.

  3. Flotillins Regulate Focal Adhesions by Interacting with α-Actinin and by Influencing the Activation of Focal Adhesion Kinase

    Directory of Open Access Journals (Sweden)

    Antje Banning

    2018-04-01

    Full Text Available Cell–matrix adhesion and cell migration are physiologically important processes that also play a major role in cancer spreading. In cultured cells, matrix adhesion depends on integrin-containing contacts such as focal adhesions. Flotillin-1 and flotillin-2 are frequently overexpressed in cancers and are associated with poor survival. Our previous studies have revealed a role for flotillin-2 in cell–matrix adhesion and in the regulation of the actin cytoskeleton. We here show that flotillins are important for cell migration in a wound healing assay and influence the morphology and dynamics of focal adhesions. Furthermore, anchorage-independent growth in soft agar is enhanced by flotillins. In the absence of flotillins, especially flotillin-2, phosphorylation of focal adhesion kinase and extracellularly regulated kinase is diminished. Flotillins interact with α-actinin, a major regulator of focal adhesion dynamics. These findings are important for understanding the molecular mechanisms of how flotillin overexpression in cancers may affect cell migration and, especially, enhance metastasis formation.

  4. Refractory Coated/Lined Low Density Structures, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — This project addresses the development of refractory coated or lined low density structures applicable for advanced future propulsion system technologies. The...

  5. Refractory Hypertension: Determination of Prevalence, Risk Factors and Comorbidities in a Large, Population-Based Cohort

    Science.gov (United States)

    Calhoun, David A.; Booth, John N.; Oparil, Suzanne; Irvin, Marguerite R.; Shimbo, Daichi; Lackland, Daniel T.; Howard, George; Safford, Monika M.; Muntner, Paul

    2014-01-01

    Refractory hypertension is an extreme phenotype of antihypertensive treatment failure. Participants in the REasons for Geographic And Racial Differences in Stroke (REGARDS) Study, a large (n=30,239), population-based cohort were evaluated to determine the prevalence of refractory hypertension and associated cardiovascular risk factors and comorbidities. Refractory hypertension was defined as uncontrolled blood pressure (systolic/diastolic ≥ 140/90 mm Hg) on ≥ 5 antihypertensive drug classes. Participants with resistant hypertension (systolic/diastolic ≥140/90 mm Hg on ≥ 3 orhypertensive participants served as comparator groups. Of 14,809 REGARDS participants receiving antihypertensive treatment, 78 (0.5%) had refractory hypertension. The prevalence of refractory hypertension was 3.6% among participants with resistant hypertension(n=2,144) and 41.7% among participants on 5 or more antihypertensive drug classes. Among all hypertensive participants, African American race, male gender, living in the stroke belt or buckle, higher body mass index, lower heart rate, reduced estimated glomerular filtration rate, albuminuria, diabetes and history of stroke and coronary heart disease were associated with refractory hypertension. Compared to resistant hypertension, prevalence ratios for refractory hypertension were increased for African Americans (3.00, 95% CI 1.68 – 5.37) and those with albuminuria (2.22, 95% CI 1.40 – 3.52) and diabetes (2.09, 95% CI 1.32 – 3.31). The median 10-year Framingham risk for coronary heart disease and stroke was higher among participants with refractory hypertension compared to either comparator group. These data indicate that while resistant hypertension is relatively common among treated hypertensive patients, true antihypertensive treatment failure is rare. PMID:24324035

  6. Super-refractory status epilepticus in West China.

    Science.gov (United States)

    Tian, L; Li, Y; Xue, X; Wu, M; Liu, F; Hao, X; Zhou, D

    2015-07-01

    This study aims to determine the general frequency, mortality, and risk factors of super-refractory status epilepticus (SRSE) versus non-refractory status epilepticus (NRSE) and refractory status epilepticus (RSE). This work is a retrospective study. Clinical data of patients who were diagnosed with status epilepticus (SE) in the neurological ward and neuro-intensive care unit of West China Hospital from January 2009 to December 2012 were collected and analyzed. A total of 98 patients were included in the study. The percentages of NRSE, RSE, and SRSE were 67.3%, 20.4%, and 12.2%, respectively. Convulsive SE was the main seizure type among the three groups. The most common cause of NRSE was related to epilepsy (EP). However, 67.7% of SRSE cases were caused by acute encephalitis. Moreover, 47% of SE and 40% of RSE cases had a history of EP, whereas only 8.3% of SRSE cases had such history (P  0.05). The general mortality of SE was 7.1%, whereas that of SRSE was 50%. During follow-up, most SRSE patients who survived have developed symptomatic EP. This study was the first to use the statistical percentage of SRSE. Approximately 12.2% of SE cases will result in SRSE, which is a challenging medical situation for doctors. Patients with first episodes and acute encephalitis were also prone to develop SRSE. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  7. The adhesive bonding of beryllium structural components

    International Nuclear Information System (INIS)

    Fullerton-Batten, R.C.

    1977-01-01

    Where service conditions permit, adhesive bonding is a highly recommendable, reliable means of joining beryllium structural parts. Several important programs have successfully used adhesive bonding for joining structural and non-structural beryllium components. Adhesive bonding minimizes stress concentrations associated with other joining techniques and considerably improves fatigue resistance. In addition, no degradation of base metal properties occur. In many instances, structural joints can be fabricated more cheaply by adhesive bonding or in combination with adhesive bonding than by any other method used alone. An evaluation program on structural adhesive bonding of beryllium sheet components is described. A suitable surface pretreatment for beryllium adherends prior to bonding is given. Tensile shear strength and fatigue properties of FM 1000 and FM 123-5 adhesive bonded joints are reviewed and compared with data obtained from riveted joints of similar geometry. (author)

  8. Electrically Conductive Epoxy Adhesives

    Directory of Open Access Journals (Sweden)

    Lan Bai

    2011-02-01

    Full Text Available Conductive adhesives are widely used in electronic packaging applications such as die attachment and solderless interconnections, component repair, display interconnections, and heat dissipation. The effects of film thickness as functions of filler volume fraction, conductive filler size, shape, as well as uncured adhesive matrix viscosity on the electrical conduction behavior of epoxy-based adhesives are presented in this work. For this purpose, epoxy-based adhesives were prepared using conductive fillers of different size, shape, and types, including Ni powder, flakes, and filaments, Ag powder, and Cu powder. The filaments were 20 μm in diameter, and 160 or 260 μm in length. HCl and H3PO4 acid solutions were used to etch and remove the surface oxide layers from the fillers. The plane resistance of filled adhesive films was measured using the four-point method. In all cases of conductive filler addition, the planar resistivity levels for the composite adhesive films increased when the film thickness was reduced. The shape of resistivity-thickness curves was negative exponential decaying type and was modeled using a mathematical relation. The relationships between the conductive film resistivities and the filler volume fractions were also derived mathematically based on the experimental data. Thus, the effects of surface treatment of filler particles, the type, size, shape of fillers, and the uncured epoxy viscosity could be included empirically by using these mathematical relations based on the experimental data. By utilizing the relations we proposed to model thickness-dependent and volume fraction-dependent conduction behaviors separately, we were able to describe the combined and coupled volume fraction-film thickness relationship mathematically based on our experimental data.

  9. Refractory experience in circulating fluidized bed combustors, Task 7

    Energy Technology Data Exchange (ETDEWEB)

    Vincent, R.Q.

    1989-11-01

    This report describes the results of an investigation into the status of the design and selection of refractory materials for coal-fueled circulating fluidized-bed combustors. The survey concentrated on operating units in the United States manufactured by six different boiler vendors: Babcock and Wilcox, Combustion Engineering, Foster Wheeler, Keeler Dorr-Oliver, Pyropower, and Riley Stoker. Information was obtained from the boiler vendors, refractory suppliers and installers, and the owners/operators of over forty units. This work is in support of DOE's Clean Coal Technology program, which includes circulating fluidized-bed technology as one of the selected concepts being evaluated.

  10. Refractory metal component technology for in-core sensor design

    International Nuclear Information System (INIS)

    Cannon, C.P.

    1986-02-01

    Within recent years, an increasing concern over reactor safety has prompted tests that characterize reactor core environments during transient conditions. Such tests include the Loss-of-Fluid-Tests (Idaho National Engineering Lab (INEL)), Severe Fuel Damage Tests (INEL), Core Debris Rubble Tests (Sandia National Laboratories (SNL)), and similar tests performed by foreign nations. The in-core sensors for these tests require refractory metal components to be compatible with electrical insulator materials as well as materials comprising highly corrosive service mediums. This paper presents the refractory metal technology utilized to provide basic sensor designs in the above mentioned reactor tests

  11. Mechanical activation of ceramic powders and its influence on the quality of the refractory linings

    International Nuclear Information System (INIS)

    Ceganac, Z.; Acimovic, Z.; Andric, Lj.; Petrov, M.; Mihajlovic, S.

    2003-01-01

    In the paper we present results of the investigation of the influence of mechanical activation of ceramic powders-talc and alumina, on the quality of refractory linings for casting applications. It is shown that additional fine grinding of ceramic powders increases the quality of the refractory lining. Grinding and activation of the particles with various granulations contributes to the creation of the homogenous continuous layer of refractory lining on the sand moulds and cores, as well as on the evaporating polystyrene patterns for applications in the Lost foam casting process. Refractory linings obtained within the activation of particles procedure have better adherence to moulds, cores and evaporating patterns. (Original)

  12. Aluminum and steel adhesion with polyurethanes from castor oil adhesives submitted to gamma irradiation

    International Nuclear Information System (INIS)

    Azevedo, Elaine C.; Assumpcao, Roberto L.; Nascimento, Eduardo M. do; Claro Neto, Salvador; Soboll, Daniel S.

    2009-01-01

    Polyurethanes adhesive from castor oil is used to join aluminum and steel pieces. The effect of gamma radiation on the resistance to tension tests is investigated. The aluminum and steel pieces after being glued with the adhesive were submitted to gamma irradiation in doses of 1 kGy, 25 kGy and 100 kGy. The rupture strength of the joints after irradiation have a slightly increase or remains practically unchanged indicating that the adhesive properties is not affected by the gamma radiation. (author)

  13. High Throughput Drug Sensitivity Assay and Genomics- Guided Treatment of Patients With Relapsed or Refractory Acute Leukemia

    Science.gov (United States)

    2018-02-28

    Acute Leukemia of Ambiguous Lineage; Recurrent Adult Acute Lymphoblastic Leukemia; Recurrent Adult Acute Myeloid Leukemia; Recurrent Childhood Acute Lymphoblastic Leukemia; Recurrent Childhood Acute Myeloid Leukemia; Refractory Acute Myeloid Leukemia; Refractory Adult Acute Lymphoblastic Leukemia; Refractory Childhood Acute Lymphoblastic Leukemia

  14. Adhesive performance of a multi-mode adhesive system: 1-year in vitro study.

    Science.gov (United States)

    Marchesi, Giulio; Frassetto, Andrea; Mazzoni, Annalisa; Apolonio, Fabianni; Diolosà, Marina; Cadenaro, Milena; Di Lenarda, Roberto; Pashley, David H; Tay, Franklin; Breschi, Lorenzo

    2014-05-01

    The aim of this study was to investigate the adhesive stability over time of a multi-mode one-step adhesive applied using different bonding techniques on human coronal dentine. The hypotheses tested were that microtensile bond strength (μTBS), interfacial nanoleakage expression and matrix metalloproteinases (MMPs) activation are not affected by the adhesive application mode (following the use of self-etch technique or with the etch-and-rinse technique on dry or wet dentine) or by ageing for 24h, 6 months and 1year in artificial saliva. Human molars were cut to expose middle/deep dentine and assigned to one of the following bonding systems (N=15): (1) Scotchbond Universal (3M ESPE) self-etch mode, (2) Scotchbond Universal etch-and-rinse technique on wet dentine, (3) Scotchbond Universal etch-and-rinse technique on dry dentine, and (4) Prime&Bond NT (Dentsply De Trey) etch-and-rinse technique on wet dentine (control). Specimens were processed for μTBS test in accordance with the non-trimming technique and stressed to failure after 24h, 6 months or 1 year. Additional specimens were processed and examined to assay interfacial nanoleakage and MMP expression. At baseline, no differences between groups were found. After 1 year of storage, Scotchbond Universal applied in the self-etch mode and Prime&Bond NT showed higher μTBS compared to the other groups. The lowest nanoleakage expression was found for Scotchbond Universal applied in the self-etch mode, both at baseline and after storage. MMPs activation was found after application of each tested adhesive. The results of this study support the use of the self-etch approach for bonding the tested multi-mode adhesive system to dentine due to improved stability over time. Improved bonding effectiveness of the tested universal adhesive system on dentine may be obtained if the adhesive is applied with the self-etch approach. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. REFRACTORY FOR BLACK LIQUOR GASIFIERS

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr.; Alireza Rezaie

    2003-12-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the materials problems encountered during the operation of low-pressure high-temperature (LFHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  16. Refractory for Black Liquor Gasifiers

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Alireza Rezaie

    2003-12-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the materials problems encountered during the operation of low-pressure high-temperature (LFHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  17. Refractory for Black Liquor Gasifiers

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Alireza Rezaie; Xiaoting Liang; Musa Karakus; Jun Wei

    2005-12-01

    The University of Missouri-Rolla identified materials that permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project was to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study attempted to define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials were selected or developed that reacted with the gasifier environment to form protective surfaces in

  18. Refractory for Black Liquor Gasifiers

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Musa Karakus; Xiaoting Liang

    2005-10-01

    The University of Missouri-Rolla identified materials that permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project was to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study attempted to define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials were selected/developed that either react with the gasifier environment to form protective surfaces in

  19. Refractory for Black Liquor Gasifiers

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick; Musa Karakus; Alireza Rezaie

    2004-03-30

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  20. REFRACTORY FOR BLACK LIQUOR GASIFIERS

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Alireza Rezaie

    2004-07-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  1. REFRACTORY FOR BLACK LIQUOR GASIFIERS

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Alireza Rezaie

    2004-10-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  2. REFRACTORY FOR BLACK LIQUOR GASIFIERS

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Jun Wei

    2005-01-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  3. REFRACTORY FOR BLACK LIQUOR GASIFIERS

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Jun Wei

    2005-04-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  4. REFRACTORY FOR BLACK LIQUOR GASIFIERS

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr; Musa Karakus; Xiaoting Liang

    2005-07-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  5. REFRACTORY FOR BLACK LIQUOR GASIFIERS

    Energy Technology Data Exchange (ETDEWEB)

    William L. Headrick Jr.; Alireza Rezaie

    2004-04-01

    The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the materials problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

  6. Superior vena cava syndrome after pulsatile bidirectional Glenn shunt procedure: Perioperative implications

    Directory of Open Access Journals (Sweden)

    Neema Praveen

    2009-01-01

    Full Text Available Bidirectional superior cavopulmonary shunt (bidirectional Glenn shunt is generally performed in many congenital cardiac anomalies where complete two ventricle circulations cannot be easily achieved. The advantages of BDG shunt are achieved by partially separating the pulmonary and systemic venous circuits, and include reduced ventricular preload and long-term preservation of myocardium. The benefits of additional pulsatile pulmonary blood flow include the potential growth of pulmonary arteries, possible improvement in arterial oxygen saturation, and possible prevention of development of pulmonary arteriovenous malformations. However, increase in the systemic venous pressure after BDG with additional pulsatile blood flow is known. We describe the peri-operative implications of severe flow reversal in the superior vena cava after pulsatile BDG shunt construction in a child who presented for surgical interruption of the main pulmonary artery.

  7. Testing Consent Order on Refractory Ceramic Fibers

    Science.gov (United States)

    This notice announces that EPA has signed signed an enforceable testing consent order under the Toxic Substances Control Act (TSCA), 15 U.S.C. section 2601 at seq., with three of the primary producers of refractory ceramic fibers (RCF).

  8. Improving outcomes of refractory celiac disease – current and emerging treatment strategies

    Directory of Open Access Journals (Sweden)

    Woodward J

    2016-08-01

    Full Text Available Jeremy Woodward Department of Gastroenterology and Clinical Nutrition, Addenbrooke’s Hospital, Cambridge, UK Abstract: Intestinal inflammation and symptoms of celiac disease (CD usually respond well to gluten withdrawal, but rare cases are refractory to diet. Two types of refractory CD are discriminated on the basis of the presence or absence of an atypical population of mucosal lymphocytes that may progress to enteropathy-associated T-cell lymphoma. Challenges remain in the secure diagnosis of both types of refractory disease, and evidence on which to base treatment recommendations is flawed by the small numbers of reported patients and the use of different diagnostic strategies. Recent advances in our understanding of the mechanisms of the condition in conjunction with the development of immunomodulatory agents for managing other inflammatory diseases are helping to shape future approaches to targeted therapy. Progression will depend on collaboration and recruitment to trials. In the meantime, there is evidence to suggest that earlier diagnosis and better follow-up and management of CD may prevent the development of refractoriness. Keywords: celiac disease, gluten, small intestine, lymphoma, lymphocytes

  9. Investigations on the viscoelastic performance of pressure sensitive adhesives in drug-in-adhesive type transdermal films.

    Science.gov (United States)

    Wolff, Hans-Michael; Irsan; Dodou, Kalliopi

    2014-08-01

    We aimed to investigate the effect of solubility parameter and drug concentration on the rheological behaviour of drug-in-adhesive films intended for transdermal application. Films were prepared over a range of drug concentrations (5%, 10% and 20% w/w) using ibuprofen, benzoic acid, nicotinic acid and lidocaine as model drugs in acrylic (Duro-Tak 87-4287 and Duro-Tak 87900A) or silicone (Bio-PSA 7-4301 and Bio-PSA 7-4302) pressure sensitive adhesives (PSAs). Saturation status of films was determined using light microscopy. Viscoelastic parameters were measured in rheology tests at 32°C. Subsaturated films had lower viscoelastic moduli whereas saturated films had higher moduli than the placebo films and/or a concentration-dependent increase in their modulus. Saturation concentration of each drug in the films was reflected by decreasing/increasing viscoelastic patterns. The viscoelastic windows (VWs) of the adhesive and drug-in-adhesive films clearly depicted the effect of solubility parameter differences, molar concentration of drug in the adhesive film and differences in PSA chemistry. Drug solubility parameters and molar drug concentrations have an impact on rheological patterns and thus on the adhesive performance of tested pressure sensitive adhesives intended for use in transdermal drug delivery systems. Use of the Flory equation in its limiting form was appropriate to predict drug solubility in the tested formulations.

  10. Glenn Seaborg's Contributions to Heavy Element Science and the Periodic Table

    International Nuclear Information System (INIS)

    Hobart, David E.

    2012-01-01

    In celebrating the centennial anniversary of the birth of Glenn T. Seaborg it is fitting that we recount and pay tribute to his legacy. Many know of the scientific accomplishments of this man who became a legend and anyone who has attended his lectures can attest to how informative, educational, and entertaining he was. He had a beguiling and whimsical sense of humor and used this to drive home his points and share his passion and quest for discovery. The periodic table is a fundamental cornerstone of science and remains a central unifying principal. Seaborg was the architect of the actinide series of elements and their proper placement in the periodic table and co-discoverer of ten transuranium elements - one of which bears his name, element 106, seaborgium. The work and achievements of this Nobel laureate have touched the lives of many and his legacy will continue for generations to come.

  11. NOVEL REFRACTORY MATERIALS FOR HIGH ALKALI, HIGH TEMPERATURE ENVIRONMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, James Gordon [ORNL; Smith, Jeffrey D [ORNL; O' Hara, Kelley [University of Missouri, Rolla; Rodrigues-Schroer, Angela [Minteq International, Inc.; Colavito, [Minteq International, Inc.

    2012-08-01

    A project was led by Oak Ridge National Laboratory (ORNL) in collaboration with a research team comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al 2O3, MgAl2O4, or other similar spinel structured or alumina-based unshaped refractory compositions (castables, gunnables, shotcretes, etc.) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, high-alkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. Both practical refractory development experience and computer modeling techniques were used to aid in the design of this new family of materials. The newly developed materials were expected to offer alternative material choices for high-temperature, high-alkali environments that were capable of operating at higher temperatures (goal of increasing operating temperature by 100-200oC depending on process) or for longer periods of time (goal of twice the life span of current materials or next process determined service increment). This would lead to less process down time, greater energy efficiency for associated manufacturing processes (more heat kept in process), and materials that could be installed/repaired in a more efficient manner. The overall project goal was a 5% improvement in energy efficiency (brought about through a 20% improvement in thermal efficiency) resulting in a savings of 3.7 TBtu/yr (7.2 billion ft3 natural gas) by the year 2030. Additionally, new

  12. Enhancing the Adhesive Strength of a Plywood Adhesive Developed from Hydrolyzed Specified Risk Materials

    Directory of Open Access Journals (Sweden)

    Birendra B. Adhikari

    2016-08-01

    Full Text Available The current production of wood composites relies mostly on formaldehyde-based adhesives such as urea formaldehyde (UF and phenol formaldehyde (PF resins. As these resins are produced from non-renewable resources, and there are some ongoing issues with possible health hazard due to formaldehyde emission from such products, the purpose of this research was to develop a formaldehyde-free plywood adhesive utilizing waste protein as a renewable feedstock. The feedstock for this work was specified risk material (SRM, which is currently being disposed of either by incineration or by landfilling. In this report, we describe a technology for utilization of SRM for the development of an environmentally friendly plywood adhesive. SRM was thermally hydrolyzed using a Canadian government-approved protocol, and the peptides were recovered from the hydrolyzate. The recovered peptides were chemically crosslinked with polyamidoamine-epichlorohydrin (PAE resin to develop an adhesive system for bonding of plywood specimens. The effects of crosslinking time, peptides/crosslinking agent ratio, and temperature of hot pressing of plywood specimens on the strength of formulated adhesives were investigated. Formulations containing as much as 78% (wt/wt peptides met the ASTM (American Society for Testing and Materials specifications of minimum dry and soaked shear strength requirement for UF resin type adhesives. Under the optimum conditions tested, the peptides–PAE resin-based formulations resulted in plywood specimens having comparable dry as well as soaked shear strength to that of commercial PF resin.

  13. Syndecan proteoglycans and cell adhesion

    DEFF Research Database (Denmark)

    Woods, A; Oh, E S; Couchman, J R

    1998-01-01

    It is now becoming clear that a family of transmembrane proteoglycans, the syndecans, have important roles in cell adhesion. They participate through binding of matrix ligand to their glycosaminoglycan chains, clustering, and the induction of signaling cascades to modify the internal microfilament...... organization. Syndecans can modulate the type of adhesive responses induced by other matrix ligand-receptor interactions, such as those involving the integrins, and so contribute to the control of cell morphology, adhesion and migration....

  14. Service life prediction for refractory materials

    Czech Academy of Sciences Publication Activity Database

    Boccaccini, D. N.; Cannio, M.; Volkov-Husović, T. D.; Kamseu, E.; Romagnoli, M.; Veronesi, P.; Leonelli, C.; Dlouhý, Ivo; Boccaccini, A. R.

    2008-01-01

    Roč. 43, č. 12 (2008), s. 4079-4090 ISSN 0022-2461 R&D Projects: GA ČR(CZ) GA106/05/0495 Institutional research plan: CEZ:AV0Z20410507 Keywords : refractory materials * ultrasonic velocity * fracture toughness Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 1.181, year: 2008

  15. Refractory chronic cluster headache

    DEFF Research Database (Denmark)

    Mitsikostas, Dimos D; Edvinsson, Lars; Jensen, Rigmor H

    2014-01-01

    Chronic cluster headache (CCH) often resists to prophylactic pharmaceutical treatments resulting in patients' life damage. In this rare but pragmatic situation escalation to invasive management is needed but framing criteria are lacking. We aimed to reach a consensus for refractory CCH definition...... for clinical and research use. The preparation of the final consensus followed three stages. Internal between authors, a larger between all European Headache Federation members and finally an international one among all investigators that have published clinical studies on cluster headache the last five years...

  16. Nerovnosti jsou ostřejší než kdykoliv předtím. Rozhovor Evelyn Nakano Glenn se Zuzanou Uhde

    Czech Academy of Sciences Publication Activity Database

    Uhde, Zuzana; Glenn, E.

    2009-01-01

    Roč. 10, č. 2 (2009), s. 58-63 ISSN 1213-0028 R&D Projects: GA AV ČR 1QS700280503 Institutional research plan: CEZ:AV0Z70280505 Keywords : feminism * interview * Evelyn N. Glenn Subject RIV: AO - Sociology, Demography http://www.genderonline.cz

  17. Effect of atmospheric-pressure plasma treatment on the adhesion properties of a thin adhesive layer in a selective transfer process

    Science.gov (United States)

    Yoon, Min-Ah; Kim, Chan; Hur, Min; Kang, Woo Seok; Kim, Jaegu; Kim, Jae-Hyun; Lee, Hak-Joo; Kim, Kwang-Seop

    2018-01-01

    The adhesion between a stamp and thin film devices is crucial for their transfer on a flexible substrate. In this paper, a thin adhesive silicone layer on the stamp was treated by atmospheric pressure plasma to locally control the adhesion strength for the selective transfer. The adhesion strength of the silicone layer was significantly reduced after the plasma treatment, while its surface energy was increased. To understand the inconsistency between the adhesion strength and surface energy changes, the surface properties of the silicone layer were characterized using nanoindentation and X-ray photoelectron spectroscopy. These techniques revealed that a thin, hard, silica-like layer had formed on the surface from plasma-enhanced oxidation. This layer played an important role in decreasing the contact area and increasing the interfacial slippage, resulting in decreased adhesion. As a practical application, the transfer process was demonstrated on GaN LEDs that had been previously delaminated by a laser lift-off (LLO) process. Although the LEDs were not transferred onto the treated adhesive layer due to the reduced adhesion, the untreated adhesive layer could readily pick up the LEDs. It is expected that this simple method of controlling the adhesion of a stamp with a thin adhesive layer would enable a continuous, selective and large-scale roll-to-roll selective transfer process and thereby advance the development of flexible, stretchable and wearable electronics.

  18. CD Bridges and STS-95 Payload Specialist Glenn greet well-wishers following a parade in Cocoa Beach

    Science.gov (United States)

    1998-01-01

    Center Director Roy Bridges and STS-95 Payload Specialist John H. Glenn Jr. greet well-wishers at a reception at the Double Tree Oceanfront Hotel following a parade down State Road A1A in nearby Cocoa Beach. Organizers of the parade included the Cocoa Beach Area Chamber of Commerce, the Brevard County Tourist Development Council, and the cities of Cape Canaveral and Cocoa Beach. The parade is reminiscent of those held after missions during the Mercury Program.

  19. Denture Adhesives in Prosthodontics: An Overview.

    Science.gov (United States)

    Kumar, P Ranjith; Shajahan, P A; Mathew, Jyothis; Koruthu, Anil; Aravind, Prasad; Ahammed, M Fazeel

    2015-01-01

    The use of denture adhesives is common among denture wearers, and it is also prescribed by many dentists. Prescribing denture adhesives has been viewed by many prosthodontists as a means of compensating for any defects in the fabrication procedures. Denture adhesives add to the retention and thereby improve chewing ability, reduce any instability, provide comfort and eliminate the accumulation of food debris beneath the dentures. Consequently, they increase the patient's sense of security and satisfaction. However, obtaining the advice of the dental practitioner prior to the use of adhesives is a must.

  20. Polyurethane adhesives in flat roofs

    Directory of Open Access Journals (Sweden)

    Bogárová Markéta

    2017-01-01

    Full Text Available It is necessary to stabilize individual layers of flat roofs, mainly because of wind suction. Apart from anchoring and surcharge, these layers can be secured by bonding. At present gluing is an indispensable and widely used stabilization method. On our market we can found many types of adhesives, most widely used are based on polyurethane. This paper focuses on problematic about stabilization thermal insulation from expanded polystyrene to vapor barrier from bitumen. One of the main issues is to calculate the exact amount of adhesive, which is required to guarantee the resistance against wind suction. In this problematic we can not find help neither in technical data sheets provided by the manufactures. Some of these data sheets contain at least information about amount of adhesive depending on location in roof plane and building height, but they do not specify the strength of such connection. It was therefore resorted to select several representatives polyurethane adhesives and their subsequent testing on specimens simulating the flat roof segment. The paper described the test methodology and results for two types of polyurethane adhesives.

  1. Study on the efficiency of ceramic coating for avoiding oxidation in carbon refractories

    International Nuclear Information System (INIS)

    Santos, I.M.G.; Cruz Junior, F.; Paskocimas, C.A.; Leite, E.R.; Longo, Elson; Varela, J.A.

    1997-01-01

    A ceramic coating made of sodium phosphossilicate and clay was developed to the protection of refractories against carbon oxidation during the pre-heating of siderurgical equipment. This search has the objective of comparing the refractory behaviour with and without coating, according to temperature, time and atmosphere. The results show that the coating is more efficient at higher temperatures. An important point is that the efficiency is smaller after long thermal is that the efficiency is smaller after long thermal treatments and at very aggressive conditions. In spite of this the oxidation is still smaller than in refractory without coating. (author)

  2. Rapid and Localized Mechanical Stimulation and Adhesion Assay: TRPM7 Involvement in Calcium Signaling and Cell Adhesion.

    Directory of Open Access Journals (Sweden)

    Wagner Shin Nishitani

    Full Text Available A cell mechanical stimulation equipment, based on cell substrate deformation, and a more sensitive method for measuring adhesion of cells were developed. A probe, precisely positioned close to the cell, was capable of a vertical localized mechanical stimulation with a temporal frequency of 207 Hz, and strain magnitude of 50%. This setup was characterized and used to probe the response of Human Umbilical Endothelial Vein Cells (HUVECs in terms of calcium signaling. The intracellular calcium ion concentration was measured by the genetically encoded Cameleon biosensor, with the Transient Receptor Potential cation channel, subfamily M, member 7 (TRPM7 expression inhibited. As TRPM7 expression also regulates adhesion, a relatively simple method for measuring adhesion of cells was also developed, tested and used to study the effect of adhesion alone. Three adhesion conditions of HUVECs on polyacrylamide gel dishes were compared. In the first condition, the substrate is fully treated with Sulfo-SANPAH crosslinking and fibronectin. The other two conditions had increasingly reduced adhesion: partially treated (only coated with fibronectin, with no use of Sulfo-SANPAH, at 5% of the normal amount and non-treated polyacrylamide gels. The cells showed adhesion and calcium response to the mechanical stimulation correlated to the degree of gel treatment: highest for fully treated gels and lowest for non-treated ones. TRPM7 inhibition by siRNA on HUVECs caused an increase in adhesion relative to control (no siRNA treatment and non-targeting siRNA, but a decrease to 80% of calcium response relative to non-targeting siRNA which confirms the important role of TRPM7 in mechanotransduction despite the increase in adhesion.

  3. Iron Refractory Iron Deficiency Anaemia: A Rare Cause of Iron Deficiency Anaemia

    LENUS (Irish Health Repository)

    McGrath, T

    2018-01-01

    We describe the case of a 17-month-old boy with a hypochromic microcytic anaemia, refractory to oral iron treatment. After exclusion of dietary and gastrointestinal causes of iron deficiency, a genetic cause for iron deficiency was confirmed by finding two mutations in the TMPRSS6 gene, consistent with a diagnosis of iron-refractory iron deficiency anaemia (IRIDA).

  4. Adhesion force imaging in air and liquid by adhesion mode atomic force microscopy

    NARCIS (Netherlands)

    van der Werf, Kees; Putman, C.A.J.; Putman, Constant A.; de Grooth, B.G.; Greve, Jan

    1994-01-01

    A new imaging mode for the atomic force microscope(AFM), yielding images mapping the adhesion force between tip and sample, is introduced. The adhesion mode AFM takes a force curve at each pixel by ramping a piezoactuator, moving the silicon‐nitride tip up and down towards the sample. During the

  5. Effects of Temperature, Oxygen Partial Pressure, and Materials Selection on Slag Infiltration into Porous Refractories for Entrained-Flow Gasifiers

    Science.gov (United States)

    Kaneko, Tetsuya Kenneth

    The penetration rate of molten mineral contents (slag) from spent carbonaceous feedstock into porous ceramic-oxide refractory linings is a critical parameter in determining the lifecycle of integrated gasification combined cycle energy production plants. Refractory linings that withstand longer operation without interruption are desirable because they can mitigate consumable and maintenance costs. Although refractory degradation has been extensively studied for many other high-temperature industrial processes, this work focuses on the mechanisms that are unique to entrained-flow gasification systems. The use of unique feedstock mixtures, temperatures from 1450 °C to 1600 °C, and oxygen partial pressures from 10-7 atm to 10-9 atm pose engineering challenges in designing an optimal refractory material. Experimentation, characterization, and modeling show that gasifier slag infiltration into porous refractory is determined by interactions between the slag and the refractory that either form a physical barrier that impedes fluid flow or induce an increased fluid viscosity that decelerates the velocity of the fluid body. The viscosity of the slag is modified by the thermal profile of the refractory along the penetration direction as well as reactions between the slag and refractory that alter the chemistry, and thereby the thermo-physical properties of the fluid. Infiltration experiments reveal that the temperature gradient inherently present along the refractory lining limits penetration. A refractory in near-isothermal conditions demonstrates deeper slag penetration as compared to one that experiences a steeper thermal profile. The decrease in the local temperatures of the slag as it travels deeper into the refractory increases the viscosity of the fluid, which in turn slows the infiltration velocity of fluid body into the pores of the refractory microstructure. With feedstock mixtures that exhibit high iron-oxide concentrations, a transition-metal-oxide, the oxygen

  6. Strategies to improve the adhesion of rubbers to adhesives by means of plasma surface modification

    Science.gov (United States)

    Martín-Martínez, J. M.; Romero-Sánchez, M. D.

    2006-05-01

    The surface modifications produced by treatment of a synthetic sulfur vulcanized styrene-butadiene rubber with oxidizing (oxygen, air, carbon dioxide) and non oxidizing (nitrogen, argon) RF low pressure plasmas, and by treatment with atmospheric plasma torch have been assessed by ATR-IR and XPS spectroscopy, SEM, and contact angle measurements. The effectiveness of the low pressure plasma treatment depended on the gas atmosphere used to generate the plasma. A lack of relationship between surface polarity and wettability, and peel strength values was obtained, likely due to the cohesive failure in the rubber obtained in the adhesive joints. In general, acceptable adhesion values of plasma treated rubber were obtained for all plasmas, except for nitrogen plasma treatment during 15 minutes due to the creation of low molecular weight moieties on the outermost rubber layer. A toluene wiping of the N{2 } plasma treated rubber surface for 15 min removed those moieties and increased adhesion was obtained. On the other hand, the treatment of the rubber with atmospheric pressure by means of a plasma torch was proposed. The wettability of the rubber was improved by decreasing the rubber-plasma torch distance and by increasing the duration because a partial removal of paraffin wax from the rubber surface was produced. The rubber surface was oxidized by the plasma torch treatment, and the longer the duration of the plasma torch treatment, the higher the degree of surface oxidation (mainly creation of C O moieties). However, although the rubber surface was effectively modified by the plasma torch treatment, the adhesion was not greatly improved, due to the migration of paraffin wax to the treated rubber-polyurethane adhesive interface once the adhesive joint was produced. On the other hand, the extended treatment with plasma torch facilitated the migration of zinc stearate to the rubber-adhesive interface, also contributing to deteriorate the adhesion in greater extent. Finally

  7. Behavior of adhesion forces of silicone adhesive sealants and mastic butyl under the influence of ionizing radiation

    International Nuclear Information System (INIS)

    Costa, Wanderley da

    2012-01-01

    Adhesives are products that can keep materials together by bonds between the surfaces. Sealants are products that can keep filled a space between two surfaces, through a barrier that is configured as a 'bridge' between the two surfaces. The mastic is a product made of a mixture of substances with the primary butyl polymer, with the consistency of a mass not dried that can be used as a sealant. The polysiloxane, also known as silicone are the most important synthetic polymers with inorganic structure, and are matrices of silicone adhesive sealants. To demonstrate the behavior of the adhesive forces of these products under different conditions, we used five different techniques. These products were subjected to two different conditions to verify the behavior of adhesion, one at the environmental condition and another under the ionizing radiation. The results showed not only differences between products (silicone and mastic), but also that the adhesive forces have different behaviors under the conditions which the samples were subjected. With this was reached the goal of this study that aspired show the differences between the mastic and silicone, this last one is often considered - erroneously - the same as mastic. Thus it was proven that: 1. silicone can be regarded as an adhesive and a sealant at ambient conditions, 2. mastic improves substantially adhesion in an environment of ionizing radiation and this property can be an excellent alternative to the adhesive market. (author)

  8. Denture adhesives: a systematic review.

    Science.gov (United States)

    Papadiochou, Sofia; Emmanouil, Ioannis; Papadiochos, Ioannis

    2015-05-01

    Denture adhesives have been the objective of scientific research for over half a century. Although they are used by denture wearers worldwide, investigations of their effectiveness and biocompatibility have led to controversial conclusions. The purpose of this study was to review the literature data with regard to the effectiveness and biocompatibility of denture adhesives as well as the attitudes of both patients and dental professionals toward these materials. An electronic search of English peer-reviewed dental literature in the Medline database was conducted to evaluate the effectiveness and biocompatibility of denture adhesives. There was no limitation in publication year, so the search included all the available scientific evidence included in that particular database until March 2014. Specific inclusion criteria were used for the selection of the appropriate articles. A manual search of the citations of the obtained articles followed to extend the electronic search. A full text review was carried out for only 32 articles. Of the 32 articles, 21 examined the efficacy of denture adhesives in terms of retention and stability and masticatory performance, 6 evaluated the issue of the biocompatibility of denture adhesives, and 5 presented the attitudes of either professionals or patients toward these materials. The majority of clinical studies supported the fact that denture adhesives enhance the retention, stability, and masticatory performance of a removable prosthesis. In terms of biocompatibility, long-term in vivo studies to investigate potential harmful effects were lacking. Patients are satisfied with denture adhesives that meet their needs. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  9. Direct brazing of ceramics, graphite, and refractory metals

    International Nuclear Information System (INIS)

    Canonico, D.A.; Cole, N.C.; Slaughter, G.M.

    1976-03-01

    ORNL has been instrumental in the development of brazing filler metals for joining ceramics, graphite, and refractory metals for application at temperatures above 1000 0 C. The philosophy and techniques employed in the development of these alloys are presented. A number of compositions are discussed that have been satisfactorily used to braze ceramics, graphite, and refractory metals without a prior surface treatment. One alloy, Ti--25 percent Cr--21 percent V, has wet and flowed on aluminum oxide and graphite. Further, it has been utilized in making brazes between different combinations of the three subject materials. The excellent flowability of this alloy and alloys from the Ti--Zr--Ge system is evidenced by the presence of filler metal in the minute pores of the graphite and ceramics

  10. Mixed Uranium/Refractory Metal Carbide Fuels for High Performance Nuclear Reactors

    International Nuclear Information System (INIS)

    Knight, Travis; Anghaie, Samim

    2002-01-01

    Single phase, solid-solution mixed uranium/refractory metal carbides have been proposed as an advanced nuclear fuel for advanced, high-performance reactors. Earlier studies of mixed carbides focused on uranium and either thorium or plutonium as a fuel for fast breeder reactors enabling shorter doubling owing to the greater fissile atom density. However, the mixed uranium/refractory carbides such as (U, Zr, Nb)C have a lower uranium densities but hold significant promise because of their ultra-high melting points (typically greater than 3700 K), improved material compatibility, and high thermal conductivity approaching that of the metal. Various compositions of (U, Zr, Nb)C were processed with 5% and 10% metal mole fraction of uranium. Stoichiometric samples were processed from the constituent carbide powders, while hypo-stoichiometric samples with carbon-to-metal (C/M) ratios of 0.92 were processed from uranium hydride, graphite, and constituent refractory carbide powders. Processing techniques of cold uniaxial pressing, dynamic magnetic compaction, sintering, and hot pressing were investigated to optimize the processing parameters necessary to produce high density (low porosity), single phase, solid-solution mixed carbide nuclear fuels for testing. This investigation was undertaken to evaluate and characterize the performance of these mixed uranium/refractory metal carbides for high performance, ultra-safe nuclear reactor applications. (authors)

  11. Adhesives from modified soy protein

    Science.gov (United States)

    Sun, Susan [Manhattan, KS; Wang, Donghai [Manhattan, KS; Zhong, Zhikai [Manhattan, KS; Yang, Guang [Shanghai, CN

    2008-08-26

    The present invention provides useful adhesive compositions having similar adhesive properties to conventional UF and PPF resins. The compositions generally include a protein portion and modifying ingredient portion selected from the group consisting of carboxyl-containing compounds, aldehyde-containing compounds, epoxy group-containing compounds, and mixtures thereof. The composition is preferably prepared at a pH level at or near the isoelectric point of the protein. In other preferred forms, the adhesive composition includes a protein portion and a carboxyl-containing group portion.

  12. Mechanisms of adhesion in geckos.

    Science.gov (United States)

    Autumn, Kellar; Peattie, Anne M

    2002-12-01

    The extraordinary adhesive capabilities of geckos have challenged explanation for millennia, since Aristotle first recorded his observations. We have discovered many of the secrets of gecko adhesion, yet the millions of dry, adhesive setae on the toes of geckos continue to generate puzzling new questions and valuable answers. Each epidermally-derived, keratinous seta ends in hundreds of 200 nm spatular tips, permitting intimate contact with rough and smooth surfaces alike. Prior studies suggested that adhesive force in gecko setae was directly proportional to the water droplet contact angle (θ) , an indicator of the free surface energy of a substrate. In contrast, new theory suggests that adhesion energy between a gecko seta and a surface (W(GS)) is in fact proportional to (1 + cosθ), and only for θ > 60°. A reanalysis of prior data, in combination with our recent study, support the van der Waals hypothesis of gecko adhesion, and contradict surface hydrophobicity as a predictor of adhesion force. Previously, we and our collaborators measured the force production of a single seta. Initial efforts to attach a seta failed because of improper 3D orientation. However, by simulating the dynamics of gecko limbs during climbing (based on force plate data) we discovered that, in single setae, a small normal preload, combined with a 5 μm displacement yielded a very large adhesive force of 200 microNewton (μN), 10 times that predicted by whole-animal measurements. 6.5 million setae of a single tokay gecko attached maximally could generate 130 kg force. This raises the question of how geckos manage to detach their feet in just 15 ms. We discovered that simply increasing the angle that the setal shaft makes with the substrate to 30° causes detachment. Understanding how simultaneous attachment and release of millions of setae are controlled will require an approach that integrates levels ranging from molecules to lizards.

  13. Approaches to refractory epilepsy

    Directory of Open Access Journals (Sweden)

    Jerome Engel

    2014-01-01

    Full Text Available Epilepsy is one of the most common serious neurological conditions, and 30 to 40% of people with epilepsy have seizures that are not controlled by medication. Patients are considered to have refractory epilepsy if disabling seizures continue despite appropriate trials of two antiseizure drugs, either alone or in combination. At this point, patients should be referred to multidisciplinary epilepsy centers that perform specialized diagnostic testing to first determine whether they are, in fact, pharmacoresistant, and then, if so, offer alternative treatments. Apparent pharmacoresistance can result from a variety of situations, including noncompliance, seizures that are not epileptic, misdiagnosis of the seizure type or epilepsy syndrome, inappropriate use of medication, and lifestyle issues. For patients who are pharmacoresistant, surgical treatment offers the best opportunity for complete freedom from seizures. Surgically remediable epilepsy syndromes have been identified, but patients with more complicated epilepsy can also benefit from surgical treatment and require more specialized evaluation, including intracranial EEG monitoring. For patients who are not surgical candidates, or who are unwilling to consider surgery, a variety of other alternative treatments can be considered, including peripheral or central neurostimulation, ketogenic diet, and complementary and alternative approaches. When such alternative treatments are not appropriate or effective, quality of life can still be greatly improved by the psychological and social support services offered by multidisciplinary epilepsy centers. A major obstacle remains the fact that only a small proportion of patients with refractory epilepsy are referred for expert evaluation and treatment.

  14. Refractory overactive bladder: Beyond oral anticholinergic therapy

    Science.gov (United States)

    Glinski, Ronald W.; Siegel, Steven

    2007-01-01

    Objectives: In this review, we discuss the treatment of refractory overactive bladder (OAB) that has not adequately responded to medication therapy and we propose an appropriate care pathway to the treatment of OAB. We also attempt to address the cost of OAB treatments. Materials and Methods: A selective expert review of the current literature on the subject of refractory OAB using MEDLINE was performed and the data is summarized. We also review our experience in treating refractory OAB. The role and outcomes of various treatment options for refractory OAB are discussed and combined therapy with oral anticholinergics is explored. Emerging remedies including intravesical botulinum toxin injection and pudendal neuromodulation are also reviewed, along with conventional surgical options. Results: In general behavioral therapy, pelvic floor electrical stimulation, magnetic therapy and posterior tibial nerve stimulation (PTNS), have shown symptom decreases in 50-80% of patients with OAB. Depending on the study, combination therapy with oral anticholinergics seems to improve efficacy of behavioral therapy and PTNS in approximately 10-30%. In multicenter, long-term randomized controlled trials, sacral neuromodulation has been shown to improve symptoms of OAB and OAB incontinence in up to 80% of the patients treated. Studies involving emerging therapies such as pudendal serve stimulation suggest that there may be a 15-20% increase in efficacy over sacral neuromodulation, but long-term studies are not yet available. Another emerging therapy, botulinum toxin, is also showing similar success in reducing OAB symptoms in 80-90% of patients. Surgical approaches, such as bladder augmentation, are a last resort in the treatment of OAB and are rarely used at this point unless upper tract damage is a concern and all other treatment options have been exhausted. Conclusion: The vast majority of OAB patients can be managed successfully by behavioral options with or without

  15. Refractory overactive bladder: Beyond oral anticholinergic therapy

    Directory of Open Access Journals (Sweden)

    Ronald W Glinski

    2007-01-01

    Full Text Available Objectives: In this review, we discuss the treatment of refractory overactive bladder (OAB that has not adequately responded to medication therapy and we propose an appropriate care pathway to the treatment of OAB. We also attempt to address the cost of OAB treatments. Materials and Methods: A selective expert review of the current literature on the subject of refractory OAB using MEDLINE was performed and the data is summarized. We also review our experience in treating refractory OAB. The role and outcomes of various treatment options for refractory OAB are discussed and combined therapy with oral anticholinergics is explored. Emerging remedies including intravesical botulinum toxin injection and pudendal neuromodulation are also reviewed, along with conventional surgical options. Results: In general behavioral therapy, pelvic floor electrical stimulation, magnetic therapy and posterior tibial nerve stimulation (PTNS, have shown symptom decreases in 50-80% of patients with OAB. Depending on the study, combination therapy with oral anticholinergics seems to improve efficacy of behavioral therapy and PTNS in approximately 10-30%. In multicenter, long-term randomized controlled trials, sacral neuromodulation has been shown to improve symptoms of OAB and OAB incontinence in up to 80% of the patients treated. Studies involving emerging therapies such as pudendal serve stimulation suggest that there may be a 15-20% increase in efficacy over sacral neuromodulation, but long-term studies are not yet available. Another emerging therapy, botulinum toxin, is also showing similar success in reducing OAB symptoms in 80-90% of patients. Surgical approaches, such as bladder augmentation, are a last resort in the treatment of OAB and are rarely used at this point unless upper tract damage is a concern and all other treatment options have been exhausted. Conclusion: The vast majority of OAB patients can be managed successfully by behavioral options with or

  16. AVTA Federal Fleet PEV Readiness Data Logging and Characterization Study for NASA Glenn Research Center

    Energy Technology Data Exchange (ETDEWEB)

    Schey, Stephen [Idaho National Lab. (INL), Idaho Falls, ID (United States); Francfort, Jim [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-10-01

    The Advanced Vehicle Testing Activity’s study seeks to collect and evaluate data to validate the utilization of advanced plug-in electric vehicle (PEV) transportation. This report focuses on the NASA Glenn Research Center (GRC) fleet to identify daily operational characteristics of select vehicles and report findings on vehicle and mission characterizations to support the successful introduction of PEVs into the agencies’ fleets. Individual observations of these selected vehicles provide the basis for recommendations related to electric vehicle adoption and whether a battery electric vehicle or plug-in hybrid electric vehicle (collectively referred to as PEVs) can fulfill the mission requirements.

  17. Tissue adhesives for simple traumatic lacerations.

    Science.gov (United States)

    Beam, Joel W

    2008-01-01

    Farion K, Osmond MH, Hartling L, et al. Tissue adhesives for traumatic lacerations in children and adults. Cochrane Database Syst Rev. 2001(4);CD003326. What is the clinical evidence base for tissue adhesives in the management of simple traumatic lacerations? Studies were identified by searches of the following databases: Cochrane Wounds Group Specialized Trials Register (September 2003), Cochrane Central Register of Controlled Trials (CENTRAL) (CDROM 2003, issue 3), MEDLINE (1966 to September 2003, week 1), EMBASE (1988 to 2003, week 36), Web of Science Science Citation Index (1975 to September 13, 2003) and various clinical trials registers (September 2003). Investigators and product manufacturers were contacted to identify additional eligible studies. The search terms included wounds and injuries, laceration, face injury, nose injury, tissue adhesives, and acrylates. Each study fulfilled the following criteria: (1) The study was a randomized controlled trial that compared tissue adhesives with standard wound closure (SWC) (sutures, staples, adhesive strips) or tissue adhesive with tissue adhesive. (2) The wounds were acute, linear lacerations less than 12 hours old, resulting from blunt or sharp trauma. (3) The wound length, width, and depth allowed for approximation of the edges with minimal tension after deep sutures were placed, if required. Studies were included with no language or publication status restriction, with participants of any age recruited in an emergency department, outpatient clinic, walk-in clinic, or other primary care setting. Studies were excluded if the wounds were stellate lacerations, puncture wounds, mammalian bites, infected, heavily contaminated or devitalized, crossing joints or mucocutaneous junctions, in hair-bearing areas, or in patients with keloid formation or chronic illness. The characteristics of the study and participants, interventions, outcome measures, and findings were extracted by one author and verified by a second

  18. Development of diagnosis and repair system for steelmaking refractories; Seikoyo taikabutsu no shindan hoshu gijutsu no kakuritsu

    Energy Technology Data Exchange (ETDEWEB)

    Aso, S.; Harada, S.; Tsutsui, Y. [Nippon Steel Corp., Tokyo (Japan)

    1996-06-01

    The latest measurement equipment and repair method were introduced into the work area of all refractories in the process of torpedo cars, hot metal preliminary treatment, hot metal pans, secondary refining, and cast pans so as to improve the cost of the newest advanced steelmaking refractories. As a result, the refractory cost could be reduced by 10%. This paper introduces the improvement in RH refractories and refractories for hot metal preliminary treatment. As for basic items, in addition to the visual observation, the thickness of refractories was quantified using equipment (laser profile meter, thermotracer, and NS sensor) for the furnace stop in the minimum remaining length. An ITV was also installed in the facilities where the visual check is difficult to carry out. Repair is mainly done by spraying. A thermal spraying repair method with high durability was used for the repair. A method that relieves a thermal shock was used for preheating. Moreover, measures that make the temperature gradient in the thickness direction uniform by using newly developed microwave drying equipment were taken for drying of unburned refractories. 4 refs., 13 figs., 2 tabs.

  19. Bone hydatid disease refractory to nitazoxanide treatment

    NARCIS (Netherlands)

    Schipper, Hans G.; Simsek, Suat; van Agtmael, Michiel A.; van Lienden, Krijn P.

    2009-01-01

    We report a patient with bone hydatid disease that was refractory to both long-term daily treatment with albendazole, combined with cimetidine or administered as monotherapy ( approximately 15 years) and a relatively short course of nitazoxanide combined with albendazole (3 months). Despite

  20. Toll-like receptor 2 expression in refractory periapical lesions.

    Science.gov (United States)

    Desai, S V; Love, R M; Rich, A M; Seymour, G J

    2011-10-01

    To investigate the expression of TLR2 in refractory periapical lesions. Refractory periapical lesion biopsies were histopathologically and clinically categorized into asymptomatic periapical granuloma (n=10), symptomatic periapical granuloma (n=10) or periapical cyst (n=10) and prepared for immunohistochemical staining using antibodies to TLR2, CD3 and CD19 or staining with methyl green pyronin. Sections were viewed under light microscopy and the presence or absence of the target cells was correlated with the histopathological and clinical data. Additionally, TLR2 expression was quantified by counting TLR(+) cells. Various mononuclear inflammatory cells in the bacteria-induced periapical lesions were reactive to TLR2 antibody, with many showing morphological similarities to lymphocytes and plasma cells. Lymphocytes were the most numerous cells in the inflammatory infiltrate. In refractory periapical granuloma, CD3(+) T cells were more numerous, whereas in periapical cysts, CD19(+) B cells were more numerous. There was a statistically significant (Pperiapical granuloma than asymptomatic periapical granuloma or periapical cyst. The presence of TLR-expressing cells in periapical granulomas and cysts provides further evidence that periapical cysts are likely to be sustained by the immune system via reaction to bacterial antigens. © 2011 International Endodontic Journal.

  1. Morphometric brain characterization of refractory obsessive-compulsive disorder: diffeomorphic anatomic registration using exponentiated Lie algebra.

    Science.gov (United States)

    Tang, Wanjie; Li, Bin; Huang, Xiaoqi; Jiang, Xiaoyu; Li, Fei; Wang, Lijuan; Chen, Taolin; Wang, Jinhui; Gong, Qiyong; Yang, Yanchun

    2013-10-01

    Few studies have used neuroimaging to characterize treatment-refractory obsessive-compulsive disorder (OCD). This study sought to explore gray matter structure in patients with treatment-refractory OCD and compare it with that of healthy controls. A total of 18 subjects with treatment-refractory OCD and 26 healthy volunteers were analyzed by MRI using a 3.0-T scanner and voxel-based morphometry (VBM). Diffeomorphic anatomical registration using exponentiated Lie algebra (DARTEL) was used to identify structural changes in gray matter associated with treatment-refractory OCD. A partial correlation model was used to analyze whether morphometric changes were associated with Yale-Brown Obsessive-Compulsive Scale scores and illness duration. Gray matter volume did not differ significantly between the two groups. Treatment-refractory OCD patients showed significantly lower gray matter density than healthy subjects in the left posterior cingulate cortex (PCC) and mediodorsal thalamus (MD) and significantly higher gray matter density in the left dorsal striatum (putamen). These changes did not correlate with symptom severity or illness duration. Our findings provide new evidence of deficits in gray matter density in treatment-refractory OCD patients. These patients may show characteristic density abnormalities in the left PCC, MD and dorsal striatum (putamen), which should be verified in longitudinal studies. © 2013. Published by Elsevier Inc. All rights reserved.

  2. Performance of refractory alloy-clad fuel pins

    International Nuclear Information System (INIS)

    Dutt, D.S.; Cox, C.M.; Millhollen, M.K.

    1984-12-01

    This paper discusses objectives and basic design of two fuel-cladding tests being conducted in support of SP-100 technology development. Two of the current space nuclear power concepts use conventional pin type designs, where a coolant removes the heat from the core and transports it to an out-of-core energy conversion system. An extensive irradiation testing program was conducted in the 1950's and 1960's to develop fuel pins for space nuclear reactors. The program emphasized refractory metal clad uranium nitride (UN), uranium carbide (UC), uranium oxide (UO 2 ), and metal matrix fuels (UCZr and BeO-UO 2 ). Based on this earlier work, studies presented here show that UN and UO 2 fuels in conjunction with several refractory metal cladding materials demonstrated high potential for meeting space reactor requirements and that UC could serve as an alternative but higher risk fuel

  3. Adhesive compositions and methods

    Science.gov (United States)

    Allen, Scott D.; Sendijarevic, Vahid; O'Connor, James

    2017-12-05

    The present invention encompasses polyurethane adhesive compositions comprising aliphatic polycarbonate chains. In one aspect, the present invention encompasses polyurethane adhesives derived from aliphatic polycarbonate polyols and polyisocyanates wherein the polyol chains contain a primary repeating unit having a structure:. In another aspect, the invention provides articles comprising the inventive polyurethane compositions as well as methods of making such compositions.

  4. Adhesive interactions with wood

    Science.gov (United States)

    Charles R. Frihart

    2004-01-01

    While the chemistry for the polymerization of wood adhesives has been studied systematically and extensively, the critical aspects of the interaction of adhesives with wood are less clearly understood. General theories of bond formation need to be modified to take into account the porosity of wood and the ability of chemicals to be absorbed into the cell wall....

  5. The effect of aggregate aspect ratio and temperature on the fracture toughness of a low cement refractory concrete

    Directory of Open Access Journals (Sweden)

    Laura Brum Prata

    2003-12-01

    Full Text Available This work investigated the influence of the aggregate's aspect ratio on the fracture behavior of a low cement aluminum silicate refractory castable treated at two different temperatures (110 °C and 1000 °C. The aggregates were cylindrical pellets with an aspect ratio of 1, 2, 3 and 4, produced by extruding a mixture of clay and calcined alumina fired at 1600 °C for 4 h to yield mullite (3Al2O3.2SiO2. The behavior of the R-Curve and other relevant fracture parameters were evaluated based on the "Two Parameter Fracture Model" in a three-point flexure test of single-edge straight through notched specimens. The two temperature treatments produced different degrees of matrix-aggregate adhesion. The larger aspect ratio aggregates were found to promote toughening only in the dried condition, at 110 °C, while the specimens fired at 1000 °C for 4 h, regardless of their aggregate aspect ratio, displayed no significant toughening. The best results for fired samples, however, were obtained from specimens containing conventional angular aggregates.

  6. Medical versus surgical treatment for refractory or recurrent peptic ulcer.

    Science.gov (United States)

    Gurusamy, Kurinchi Selvan; Pallari, Elena

    2016-03-29

    Refractory peptic ulcers are ulcers in the stomach or duodenum that do not heal after eight to 12 weeks of medical treatment or those that are associated with complications despite medical treatment. Recurrent peptic ulcers are peptic ulcers that recur after healing of the ulcer. Given the number of deaths due to peptic ulcer-related complications and the long-term complications of medical treatment (increased incidence of fracture), it is unclear whether medical or surgical intervention is the better treatment option in people with recurrent or refractory peptic ulcers. To assess the benefits and harms of medical versus surgical treatment for people with recurrent or refractory peptic ulcer. We searched the specialised register of the Cochrane Upper GI and Pancreatic Diseases group, the Cochrane Central Register of Controlled Trials (CENTRAL) in the Cochrane Library, MEDLINE, EMBASE, Science Citation Index Expanded, and trials registers until September 2015 to identify randomised trials and non-randomised studies, using search strategies. We also searched the references of included studies to identify further studies. We considered randomised controlled trials and non-randomised studies comparing medical treatment with surgical treatment in people with refractory or recurrent peptic ulcer, irrespective of language, blinding, or publication status for inclusion in the review. Two review authors independently identified trials and extracted data. We planned to calculate the risk ratio, mean difference, standardised mean difference, or hazard ratio with 95% confidence intervals using both fixed-effect and random-effects models with Review Manager 5 based on intention-to-treat analysis. We included only one non-randomised study published 30 years ago in the review. This study included 77 participants who had gastric ulcer and in whom medical therapy (histamine H2 receptor blockers, antacids, and diet) had failed after an average duration of treatment of 29 months. The

  7. Sorption techniques for production of high purity refractory metals

    International Nuclear Information System (INIS)

    Shatalov, V.V.; Peganov, V.A.; Logvinenko, I.A.; Molchanova, T.V.

    2004-01-01

    A consideration is given to potentialities of sorption processes tot provide a high quality of refractory metal and their alloys when using hydrometallurgical methods for raw material processing. The efficiency of application of ion exchange technology is shown for complex solutions reprocessing for various types of polymetallic raw materials, among them uranium ores, enriched concentrates of refractory metal ores, intermediate products, waste solutions. Based on investigation results on the behaviour of elements in process solutions and the mechanism of their sorption and elution, the process of pure chemical compounds production are developed which provide thereafter manufacturing compact metals. The flowsheets developed are mastered on a commercial scale [ru

  8. Human climbing with efficiently scaled gecko-inspired dry adhesives

    OpenAIRE

    Hawkes, Elliot W.; Eason, Eric V.; Christensen, David L.; Cutkosky, Mark R.

    2015-01-01

    Since the discovery of the mechanism of adhesion in geckos, many synthetic dry adhesives have been developed with desirable gecko-like properties such as reusability, directionality, self-cleaning ability, rough surface adhesion and high adhesive stress. However, fully exploiting these adhesives in practical applications at different length scales requires efficient scaling (i.e. with little loss in adhesion as area grows). Just as natural gecko adhesives have been used as a benchmark for syn...

  9. Response to parenteral iron therapy distinguish unexplained refractory iron deficiency anemia from iron-refractory iron deficiency anemia.

    Science.gov (United States)

    Akin, M; Sarbay, H; Guler, S; Balci, Y I; Polat, A

    2016-04-01

    We evaluated that response to parenteral iron therapy could be helpful in distinguishing the types of iron deficiency anemia. This study analyzed responses to IV iron sucrose therapy of 15 children with unexplained refractory iron deficiency anemia (URIDA). We compared the results at diagnosis, 6 weeks and 6 months after the therapy. Results were compared with responses of 11 patients' results with iron-refractory iron deficiency anemia (IRIDA) from our previous study. Six weeks after the start of treatment, ferritin, MCV, MCH and Hb values were in normal range in 10 patients. The increase in Hb, MCH, MCV, and ferritin values ranged 2.6-3.5 g/dL, 1.7-4.2 pg, 2-9 fL, and 13-25 ng/mL, respectively. In five patients, Hb, MCH, and MCV mean (range) values [11.2 g/dL (11-12.2), 24.5 pg (24-25.6), and 67 fL (65-70)] were nearly normal but ferritin mean (range) values [9.8 ng/mL (8-11)] were below normal. Six weeks after the start of treatment, Hb, MCH, MCV and ferritin values of patients with IRIDA were increased. The increase in Hb, MCH, MCV, and ferritin values ranged 0.8-2.7 g/dL, 1.7-4.2 pg, 2-9 fL, and 13-25 ng/mL, respectively. IRIDA is only partially responsive to parenteral iron supplementation. In conclusion, this study demonstrated that the response to intravenous iron therapy for the URIDA cases improved blood parameters more effectively than hereditary IRIDA. Response to parenteral iron therapy would be helpful to distinguish unexplained refractory IDA from hereditary IRIDA for clinicians who do not have access to hepcidin or TMPRS6 mutation analysis. © 2016 John Wiley & Sons Ltd.

  10. Adhesion Between Poly(dimethylsiloxane) Layers

    DEFF Research Database (Denmark)

    Yu, Liyun; Daugaard, Anders Egede; Skov, Anne Ladegaard

    Different adhesion methods of poly(dimethylsiloxane) (PDMS) layers were studied with respect to adhesional force and the resulting rheology of the two-layered PDMS films were investigated. The role of adhesion between PDMS layers on the performances of two-layer structures was studied with peel...... strength test and by SEM pictures. The rheology of the double-layered compared to the monolayer films changed in some cases which indicates that the adhesion process needs to be carefully introduced in order not to alter the final properties....

  11. Low-temperature plasma spheroidizing of polydisperse powders of refractory materials

    International Nuclear Information System (INIS)

    Tsymbalist, M.M.; Rudenskaya, N.A.; Kuz'min, B.P.; Pan'kov, V.A.

    2003-01-01

    A model is developed for heating and melting of a spherical particle, when powder processing in low temperature plasma, with the aim of estimation of the dependence of the degree of fusion on particle size for various materials. Spheroidizing of various refractory material powders close in shape and size composition is experimentally performed. Experimental and calculation estimates of spheroidizing criteria for the materials studied are in a satisfactory agreement. The influence of basic physical properties of refractory materials and plasma processing parameters on the degree of particle spheroidizing is analyzed [ru

  12. Gecko-inspired bidirectional double-sided adhesives.

    Science.gov (United States)

    Wang, Zhengzhi; Gu, Ping; Wu, Xiaoping

    2014-05-14

    A new concept of gecko-inspired double-sided adhesives (DSAs) is presented. The DSAs, constructed by dual-angled (i.e. angled base and angled tip) micro-pillars on both sides of the backplane substrate, are fabricated by combinations of angled etching, mould replication, tip modification, and curing bonding. Two types of DSA, symmetric and antisymmetric (i.e. pillars are patterned symmetrically or antisymmetrically relative to the backplane), are fabricated and studied in comparison with the single-sided adhesive (SSA) counterparts through both non-conformal and conformal tests. Results indicate that the DSAs show controllable and bidirectional adhesion. Combination of the two pillar-layers can either amplify (for the antisymmetric DSA, providing a remarkable and durable adhesion capacity of 25.8 ± 2.8 N cm⁻² and a high anisotropy ratio of ∼8) or counteract (for the symmetric DSA, generating almost isotropic adhesion) the adhesion capacity and anisotropic level of one SSA (capacity of 16.2 ± 1.7 N cm⁻² and anisotropy ratio of ∼6). We demonstrate that these two DSAs can be utilized as a facile fastener for two individual objects and a small-scale delivery setup, respectively, complementing the functionality of the commonly studied SSA. As such, the double-sided patterning is believed to be a new branch in the further development of biomimetic dry adhesives.

  13. Shear Adhesion of Tapered Nanopillar Arrays.

    Science.gov (United States)

    Cho, Younghyun; Minsky, Helen K; Jiang, Yijie; Yin, Kaiyang; Turner, Kevin T; Yang, Shu

    2018-04-04

    Tapered nanopillars with various cross sections, including cone-shaped, stepwise, and pencil-like structures (300 nm in diameter at the base of the pillars and 1.1 μm in height), are prepared from epoxy resin templated by nanoporous anodic aluminum oxide (AAO) membranes. The effect of pillar geometry on the shear adhesion behavior of these nanopillar arrays is investigated via sliding experiments in a nanoindentation system. In a previous study of arrays with the same geometry, it was shown that cone-shaped nanopillars exhibit the highest adhesion under normal loading while stepwise and pencil-like nanopillars exhibit lower normal adhesion strength due to significant deformation of the pillars that occurs with increasing indentation depth. Contrary to the previous studies, here, we show that pencil-like nanopillars exhibit the highest shear adhesion strength at all indentation depths among three types of nanopillar arrays and that the shear adhesion increases with greater indentation depth due to the higher bending stiffness and closer packing of the pencil-like nanopillar array. Finite element simulations are used to elucidate the deformation of the pillars during the sliding experiments and agree with the nanoindentation-based sliding measurements. The experiments and finite element simulations together demonstrate that the shape of the nanopillars plays a key role in shear adhesion and that the mechanism is quite different from that of adhesion under normal loading.

  14. Colonic exclusion and combined therapy for refractory constipation.

    Science.gov (United States)

    Peng, Hong-Yun; Xu, Ai-Zhong

    2006-12-28

    To investigate the therapeutic effectiveness of colonic exclusion and combined therapy for refractory constipation. Thirty-two patients with refractory constipation were randomly divided into treatment group (n = 14) and control group (n = 18). Fourteen patients in treatment group underwent colonic exclusion and end-to-side colorectal anastomosis. Eighteen patients in control group received subtotal colectomy and end-to-end colorectal anastomosis. The therapeutic effects of the operations were assessed by comparing the surgical time, incision length, volume of blood losses, hospital stay, recovery rate and complication incidence. All patients received long-term follow-up. All operations were successful and patients recovered fully after the operations. In comparison of treatment group and control group, the surgical time (h), incision length (cm), volume of blood losses (mL), hospital stay (d) were 87 +/- 16 min vs 194 +/- 23 min (t = 9.85), 10.4 +/- 0.5 cm vs 21.2 +/- 1.8 cm (t = 14.26), 79.5 +/- 31.3 mL vs 286.3 +/- 49.2 mL (t = 17.24), and 11.8 +/- 2.4 d vs 18.6 +/- 2.6 d (t = 6.91), respectively (P 0.05), 21.4% vs 33.3% (P = 0.73 > 0.05), respectively. Colonic exclusion has better therapeutic efficacy on refractory constipation. It has many advantages such as shorter surgical time, smaller incision, fewer blood losses and shorter hospital stay.

  15. The adhesion of pacemaker skin wounds with Histoacryl tissue adhesive: an analysis of its efficacy and cost

    International Nuclear Information System (INIS)

    Zhou Yong; Jiang Haibin; Qin Yongwen; Chen Shaoping

    2011-01-01

    Objective: To evaluate the clinical efficacy and cost of Histoacryl tissue adhesive in adhering the pacemaker skin wounds. Methods: During the period from April 2010 to October 2010, permanent cardiac pacemaker implantation was performed in 112 patients in authors' hospital. The patients were divided into tissue adhesive group (n=64) and conventional suture group (n=48). Histoacryl tissue adhesive was employed in patients of tissue adhesive group. The extent of wound healing, the post-procedure hospitalization days and the hospitalization cost were recorded, and the results were compared between the two groups. Results: The clinical baselines of the two groups were compatible with each other. Primary closure of wounds was achieved in all patients of two groups. The mean post-procedure hospitalization time in tissue adhesive group and in conventional suture group was (4.4±1.4) days and (6.2±1.3) days respectively, the difference between the two groups was statistically significant (P<0.01). If the costs of pacemaker equipment, surgery and DSA were not included, the mean medical expenses in tissue adhesive group and in conventional suture group were (4383.39±792.40) and (4199.81±1059.93) Chinese Yuan respectively, and no significant difference in medical expenses existed between the two groups (P=0.651). Conclusion: Histoacryl tissue adhesive can effectively adhere pacemaker wounds tissue. Compared to the use of conventional suture, the use of Histoacryl tissue adhesive can reduce the post-procedure hospitalization days although the medical expenses are quite the same as that using conventional suture treatment. (authors)

  16. Self-assembled Nano-layering at the Adhesive interface.

    Science.gov (United States)

    Yoshida, Y; Yoshihara, K; Nagaoka, N; Hayakawa, S; Torii, Y; Ogawa, T; Osaka, A; Meerbeek, B Van

    2012-04-01

    According to the 'Adhesion-Decalcification' concept, specific functional monomers within dental adhesives can ionically interact with hydroxyapatite (HAp). Such ionic bonding has been demonstrated for 10-methacryloyloxydecyl dihydrogen phosphate (MDP) to manifest in the form of self-assembled 'nano-layering'. However, it remained to be explored if such nano-layering also occurs on tooth tissue when commercial MDP-containing adhesives (Clearfil SE Bond, Kuraray; Scotchbond Universal, 3M ESPE) were applied following common clinical application protocols. We therefore characterized adhesive-dentin interfaces chemically, using x-ray diffraction (XRD) and energy-dispersive x-ray spectroscopy (EDS), and ultrastructurally, using (scanning) transmission electron microscopy (TEM/STEM). Both adhesives revealed nano-layering at the adhesive interface, not only within the hybrid layer but also, particularly for Clearfil SE Bond (Kuraray), extending into the adhesive layer. Since such self-assembled nano-layering of two 10-MDP molecules, joined by stable MDP-Ca salt formation, must make the adhesive interface more resistant to biodegradation, it may well explain the documented favorable clinical longevity of bonds produced by 10-MDP-based adhesives.

  17. Lightweight cordierite–mullite refractories with low coefficients of ...

    Indian Academy of Sciences (India)

    of thermal conductivity and high mechanical properties ... compositions and microstructures of lightweight refractories were measured by X-ray .... of matrices were determined by calibration with EDAX ZAF .... Guzman I Ya 2003 Glass Ceram.

  18. High-performance mussel-inspired adhesives of reduced complexity.

    Science.gov (United States)

    Ahn, B Kollbe; Das, Saurabh; Linstadt, Roscoe; Kaufman, Yair; Martinez-Rodriguez, Nadine R; Mirshafian, Razieh; Kesselman, Ellina; Talmon, Yeshayahu; Lipshutz, Bruce H; Israelachvili, Jacob N; Waite, J Herbert

    2015-10-19

    Despite the recent progress in and demand for wet adhesives, practical underwater adhesion remains limited or non-existent for diverse applications. Translation of mussel-inspired wet adhesion typically entails catechol functionalization of polymers and/or polyelectrolytes, and solution processing of many complex components and steps that require optimization and stabilization. Here we reduced the complexity of a wet adhesive primer to synthetic low-molecular-weight catecholic zwitterionic surfactants that show very strong adhesion (∼50 mJ m(-2)) and retain the ability to coacervate. This catecholic zwitterion adheres to diverse surfaces and self-assembles into a molecularly smooth, thin (adhesive for nanofabrication. This study significantly simplifies bio-inspired themes for wet adhesion by combining catechol with hydrophobic and electrostatic functional groups in a small molecule.

  19. Understanding Surface Adhesion in Nature: A Peeling Model.

    Science.gov (United States)

    Gu, Zhen; Li, Siheng; Zhang, Feilong; Wang, Shutao

    2016-07-01

    Nature often exhibits various interesting and unique adhesive surfaces. The attempt to understand the natural adhesion phenomena can continuously guide the design of artificial adhesive surfaces by proposing simplified models of surface adhesion. Among those models, a peeling model can often effectively reflect the adhesive property between two surfaces during their attachment and detachment processes. In the context, this review summarizes the recent advances about the peeling model in understanding unique adhesive properties on natural and artificial surfaces. It mainly includes four parts: a brief introduction to natural surface adhesion, the theoretical basis and progress of the peeling model, application of the peeling model, and finally, conclusions. It is believed that this review is helpful to various fields, such as surface engineering, biomedicine, microelectronics, and so on.

  20. Infliximab TNF-alpha antagonist decreases intraabdominal adhesions

    International Nuclear Information System (INIS)

    Kurukahvecioglu, O.; Koksal, H.; Yazicioglu, O.; Kerem, M.; Taneri, F.; Gulbahar, O.; Erdem, O.; Engin, D.

    2007-01-01

    Objective was to evaluate the effect of infliximab on adhesion formation and its associated morbidity and complications. This study was performed in the Faculty of Medicine, Gaze University, Turkey between July 2005 and October 2005. Thirty-five rats were randomly divided into 4 groups. Laparotomy was performed in the Sham group (n=5), whereas cecal abrasion was carried out in all other groups. After cecal abrasion 0.9% sodium chloride was administered in the saline group (n=10), infliximab was administered to the study group (n=10) and nothing was administered to the last group (n=10). Adhesion formation was evaluated with macroscopic adhesion scoring systems. Peritoneal fluid samples and mesenteric lymph node biopsies were taken to rule out bacterial peritonitis. Blood and peritoneal irrigation fluids samples were taken to measure the Tumor necrosis factor-alpha (TNF-alpha) levels. Macroscopic adhesion scores showed fewer adhesions in the infliximab group. The infliximab group had significantly fewer adhesions than the abrasion control and saline groups. According to the histological findings, there were no statistically significant differences between the groups. Early blocking of the activity of TNF-alpha after cecal abrasion resulted in lower rates of adhesion formation, macroscopically. The TNF-alpha, a proinflammatory cytokine appears to be an important mediator for postoperative adhesion formation. (author)

  1. Silk Fibroin Aqueous-Based Adhesives Inspired by Mussel Adhesive Proteins.

    Science.gov (United States)

    Burke, Kelly A; Roberts, Dane C; Kaplan, David L

    2016-01-11

    Silk fibroin from the domesticated silkworm Bombyx mori is a naturally occurring biopolymer with charged hydrophilic terminal regions that end-cap a hydrophobic core consisting of repeating sequences of glycine, alanine, and serine residues. Taking inspiration from mussels that produce proteins rich in L-3,4-dihydroxyphenylalanine (DOPA) to adhere to a variety of organic and inorganic surfaces, the silk fibroin was functionalized with catechol groups. Silk fibroin was selected for its high molecular weight, tunable mechanical and degradation properties, aqueous processability, and wide availability. The synthesis of catechol-functionalized silk fibroin polymers containing varying amounts of hydrophilic polyethylene glycol (PEG, 5000 g/mol) side chains was carried out to balance silk hydrophobicity with PEG hydrophilicity. The efficiency of the catechol functionalization reaction did not vary with PEG conjugation over the range studied, although tuning the amount of PEG conjugated was essential for aqueous solubility. Adhesive bonding and cell compatibility of the resulting materials were investigated, where it was found that incorporating as little as 6 wt % PEG prior to catechol functionalization resulted in complete aqueous solubility of the catechol conjugates and increased adhesive strength compared with silk lacking catechol functionalization. Furthermore, PEG-silk fibroin conjugates maintained their ability to form β-sheet secondary structures, which can be exploited to reduce swelling. Human mesenchymal stem cells (hMSCs) proliferated on the silks, regardless of PEG and catechol conjugation. These materials represent a protein-based approach to catechol-based adhesives, which we envision may find applicability as biodegradable adhesives and sealants.

  2. Predictive simulation of bidirectional Glenn shunt using a hybrid blood vessel model.

    Science.gov (United States)

    Li, Hao; Leow, Wee Kheng; Chiu, Ing-Sh

    2009-01-01

    This paper proposes a method for performing predictive simulation of cardiac surgery. It applies a hybrid approach to model the deformation of blood vessels. The hybrid blood vessel model consists of a reference Cosserat rod and a surface mesh. The reference Cosserat rod models the blood vessel's global bending, stretching, twisting and shearing in a physically correct manner, and the surface mesh models the surface details of the blood vessel. In this way, the deformation of blood vessels can be computed efficiently and accurately. Our predictive simulation system can produce complex surgical results given a small amount of user inputs. It allows the surgeon to easily explore various surgical options and evaluate them. Tests of the system using bidirectional Glenn shunt (BDG) as an application example show that the results produc by the system are similar to real surgical results.

  3. NASA Glenn Research Center Solar Cell Experiment Onboard the International Space Station

    Science.gov (United States)

    Myers, Matthew G.; Wolford, David S.; Prokop, Norman F.; Krasowski, Michael J.; Parker, David S.; Cassidy, Justin C.; Davies , William E.; Vorreiter, Janelle O.; Piszczor, Michael F.; Mcnatt, Jeremiah S.; hide

    2016-01-01

    Accurate air mass zero (AM0) measurement is essential for the evaluation of new photovoltaic (PV) technology for space solar cells. The NASA Glenn Research Center (GRC) has flown an experiment designed to measure the electrical performance of several solar cells onboard NASA Goddard Space Flight Center's (GSFC) Robotic Refueling Missions (RRM) Task Board 4 (TB4) on the exterior of the International Space Station (ISS). Four industry and government partners provided advanced PV devices for measurement and orbital environment testing. The experiment was positioned on the exterior of the station for approximately eight months, and was completely self-contained, providing its own power and internal data storage. Several new cell technologies including four-junction (4J) Inverted Metamorphic Multi-junction (IMM) cells were evaluated and the results will be compared to ground-based measurement methods.

  4. Advances in biomaterials for preventing tissue adhesion.

    Science.gov (United States)

    Wu, Wei; Cheng, Ruoyu; das Neves, José; Tang, Jincheng; Xiao, Junyuan; Ni, Qing; Liu, Xinnong; Pan, Guoqing; Li, Dechun; Cui, Wenguo; Sarmento, Bruno

    2017-09-10

    Adhesion is one of the most common postsurgical complications, occurring simultaneously as the damaged tissue heals. Accompanied by symptoms such as inflammation, pain and even dyskinesia in particular circumstances, tissue adhesion has substantially compromised the quality of life of patients. Instead of passive treatment, which involves high cost and prolonged hospital stay, active intervention to prevent the adhesion from happening has been accepted as the optimized strategy against this complication. Herein, this paper will cover not only the mechanism of adhesion forming, but also the biomaterials and medicines used in its prevention. Apart from acting as a direct barrier, biomaterials also show promising anti-adhesive bioactivity though their intrinsic physical and chemical are still not completely unveiled. Considering the diversity of human tissue organization, it is imperative that various biomaterials in combination with specific medicine could be tuned to fit the microenvironment of targeted tissues. With the illustration of different adhesion mechanism and solutions, we hope this review can become a beacon and further inspires the development of anti-adhesion biomedicines. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Antipsychotic Polypharmacy in a Treatment-Refractory Schizophrenia Population Receiving Adjunctive Treatment With Electroconvulsive Therapy

    DEFF Research Database (Denmark)

    Kristensen, Diana; Hageman, Ida; Bauer, Jeanett

    2013-01-01

    Antipsychotic polypharmacy (APP) is frequent, but its pattern is unknown in treatment-refractory schizophrenia-spectrum patients receiving electroconvulsive therapy (ECT).......Antipsychotic polypharmacy (APP) is frequent, but its pattern is unknown in treatment-refractory schizophrenia-spectrum patients receiving electroconvulsive therapy (ECT)....

  6. Structural adhesives directory and databook

    CERN Document Server

    Wilson, Jo

    1996-01-01

    A worldwide directory of commercially available adhesive products for use in a wide range of engineering disciplines. Along with product names and suppliers, basic property data are tabulated and cross-referenced. The book is subdivided according to class of adhesive, with introductions to each class followed by comparison tables and datasheets for each adhesive. The datasheets contain detailed information, from product codes to environmental properties and are therefore of interest across a broad readership. Standardized data will aid the user in cross-comparison between different manufacturers and in easily identifying the required information.

  7. Controllable biomimetic adhesion using embedded phase change material

    International Nuclear Information System (INIS)

    Krahn, J; Sameoto, D; Menon, C

    2011-01-01

    In many cases, such as in the instance of climbing robots or temporary adhesives, there is the need to be able to dynamically control the level of adhesion a biomimetic dry adhesive can provide. In this study, the effect of changing the backing layer stiffness of a dry adhesive is examined. Embedding a phase change material within the backing of a synthetic dry adhesive sheet allows the stiffness to be tailored at different points of a preload and adhesion cycle. Larger contact areas and more equal load sharing between adhesive fibres can be achieved by increasing the backing layer stiffness after initial deformation when the adhesive backing is loaded in its softened state. Adhesion behaviour is examined when the backing layer is maintained in solid and softened phases during complete load cycles and for load cycles under the condition of contact with the softened phase backing followed by pull-off during the solid phase. Absolute adhesion force is increased for trials in which a soft backing layer hardens prior to pull-off. This effect is due to the increased contact area made between the rounded probe and the softened material during preloading and the more equal load sharing condition during pull-off when the backing layer becomes stiff again

  8. Lignin-Furfural Based Adhesives

    Directory of Open Access Journals (Sweden)

    Prajakta Dongre

    2015-07-01

    Full Text Available Lignin recovered from the hot-water extract of sugar maple (Acer saccharum is used in this study to synthesize adhesive blends to replace phenol-formaldehyde (PF resin. Untreated lignin is characterized by lignin content and nuclear magnetic resonance (NMR analysis. The molecular weight distribution of the lignin and the blends are characterized by size exclusion chromatography (SEC. The effect of pH (0.3, 0.65 and 1, ex situ furfural, and curing conditions on the tensile properties of adhesive reinforced glass fibers is determined and compared to the reinforcement level of commercially available PF resin. The adhesive blend prepared at pH = 0.65 with no added furfural exhibits the highest tensile properties and meets 90% of the PF tensile strength.

  9. Advances in modeling and design of adhesively bonded systems

    CERN Document Server

    Kumar, S

    2013-01-01

    The book comprehensively charts a way for industry to employ adhesively bonded joints to make systems more efficient and cost-effective Adhesively bonded systems have found applications in a wide spectrum of industries (e.g., aerospace, electronics, construction, ship building, biomedical, etc.) for a variety of purposes. Emerging adhesive materials with improved mechanical properties have allowed adhesion strength approaching that of the bonded materials themselves. Due to advances in adhesive materials and the many potential merits that adhesive bonding offers, adhesive bonding has replac

  10. Adhesion of Antireflective Coatings in Multijunction Photovoltaics: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Brock, Ryan; Dauskardt, Reinhold H.; Miller, David C.

    2016-06-16

    The development of a new composite dual cantilever beam (cDCB) thin-film adhesion testing method is reported, which allows the measurement of adhesion on the fragile thin substrates used in multijunction photovoltaics. We address the adhesion of several antireflective coating systems on multijunction cells. By varying interface chemistry and morphology, we demonstrate the ensuing effects on adhesion and help to develop an understanding of how high adhesion can be achieved, as adhesion values ranging from 0.5 J/m2 to 10 J/m2 were measured. Damp Heat (85 degrees C/85% RH) was used to invoke degradation of interfacial adhesion. We show that even with germanium substrates that fracture easily, quantitative measurements of adhesion can still be made at high test yield. The cDCB test is discussed as an important new methodology, which can be broadly applied to any system that makes use of thin, brittle, or otherwise fragile substrates.

  11. Sliding Adhesion Dynamics of Isolated Gecko Setal Arrays

    Science.gov (United States)

    Sponberg, Simon; Autumn, Kellar

    2003-03-01

    The tokay gecko (Gekko gecko) can adhere to nearly any surface through van der Waals interactions of the specialized setae (b-keratin "hairs") of its toe pads. Our recent research has suggested that a gecko is substantially overbuilt for static adhesion requiring as little as 0.03of its theoretical adhesive capacity. We performed the first sliding adhesion experiments on this novel biological adhesive to determine its response to dynamic loading. We isolated arrays of setae and constructed a precision controlled Robo-toe to study sliding effects. Our results indicate that, unlike many typical adhesives, gecko setal arrays exhibit an increased frictional force upon sliding (mk > ms) which further increases with velocity, suggesting that perturbation rejection may be an evolutionary design principle underlying the evolution of the gecko adhesive. We compare these dynamic properties with those of other adhesives and explore the impacts of these results on the design of artificial adhesives.

  12. Morphological differentiation of severe aplastic anaemia from hypocellular refractory cytopenia of childhood

    DEFF Research Database (Denmark)

    Baumann, Irith; Führer, Monika; Behrendt, Sonja

    2012-01-01

    To evaluate the reproducibility and reliability of the histomorphological criteria differentiating severe aplastic anaemia (SAA) and hypoplastic refractory cytopenia of childhood (RCC), the most frequently acquired hypocellular bone marrow conditions of childhood.......To evaluate the reproducibility and reliability of the histomorphological criteria differentiating severe aplastic anaemia (SAA) and hypoplastic refractory cytopenia of childhood (RCC), the most frequently acquired hypocellular bone marrow conditions of childhood....

  13. Advances in multidisciplinary individualized treatment of refractory hepatic alveolar echinococcosis

    Directory of Open Access Journals (Sweden)

    ABUDUAINI Abulizi

    2015-04-01

    Full Text Available Hepatic alveolar echinococcosis (HAE is a zoonotic parasitic disease that seriously threatens the population in western China and compromises patients′ quality of life. With the continuous improvement in radical resection rate in recent years, late-stage HAE patients that were incurable in the past now have the opportunity for radical resection. However, patients who are not suitable candidates for radical resection still suffer from various complications and poor quality of life. Therefore, HAE is still considered a refractory and complex disease. The simple empirical treatment model provided by traditional professional discussion is unable to satisfy the treatment of advanced refractory HAE as it is unable to integrate specialized, standardized clinical skills for diagnosis and treatment. Multidisciplinary individualized treatment (MDT organically integrates the advantages of the available treatment into a reasonable individualized comprehensive treatment regimen. This review summarizes the advances in MDT for HAE as the best option to increase long-term survival, and suggests MDT as the first-line treatment for late-stage refractory hepatic alveolar echinococcosis.

  14. Funding and Strategic Alignment Guidance for Infusing Small Business Innovation Research Technology Into Science Mission Directorate Projects at Glenn Research Center for 2015

    Science.gov (United States)

    Nguyen, Hung D.; Steele, Gynelle C.

    2016-01-01

    This report is intended to help NASA program and project managers incorporate Glenn ResearchCenter Small Business Innovation Research/Small Business Technology Transfer (SBIR)/(STTR)technologies into NASA Science Mission Directorate (SMD) programs/projects. Other Government and commercial project managers can also find this useful.

  15. Adhesion mechanisms of nanoparticle silver to substrate materials: identification

    International Nuclear Information System (INIS)

    Joo, Sungchul; Baldwin, Daniel F

    2010-01-01

    Nanoparticle silver (NPS) conductors are increasingly being investigated for printed electronics applications. However, the adhesion mechanism of the nanoparticle silver to substrate materials has not been identified yet. In particular, the adhesion of NPS to organic materials such as the widely used polyimide Kapton HN and Kapton FPC dry films is concerned with low adhesion strength because the processed polymer surface is chemically inert. Moreover, its adhesion to substrate materials such as benzocyclobutene (BCB), copper and aluminum was found to be very weak. Therefore, in this paper, the mechanisms of NPS adhesion to organic and inorganic materials are identified as the first step in improving NPS adhesion strength. Improving the adhesion strength of NPS will be the key issue for printed electronics applications. The adhesion of NPS to substrate materials was found to be mainly attributed to van der Waals forces based on particle adhesion mechanisms. This finding provides the initiative of developing an adhesion prediction model of NPS to substrate materials in order to provide guidelines for improving the NPS adhesion strength to the substrate materials used in printed electronics.

  16. Immunomodulatory therapy in refractory/recurrent ovarian cancer

    Directory of Open Access Journals (Sweden)

    Chao-Yu Chen

    2015-04-01

    Conclusion: IMT alone or add-on to palliative/salvage chemotherapy for refractory/recurrent EOC achieves a substantial disease stabilizing rate without severe toxicity, which might be a potential option in selected patients. The ALC 1 month after IMT could be an early indicator to disease stabilization.

  17. Decision Making during the Psychological Refractory Period

    NARCIS (Netherlands)

    Zylberberg, Ariel; Ouellette, Brian; Sigman, Mariano; Roelfsema, Pieter R.

    2012-01-01

    In spite of its massively parallel architecture [1], the human brain is fundamentally limited if required to perform two tasks at the same time [2, 3]. This limitation can be studied with the psychological refractory period (PRP) paradigm, where two stimuli that require speeded responses occur in

  18. Bacterial adhesion to unworn and worn silicone hydrogel lenses.

    Science.gov (United States)

    Vijay, Ajay Kumar; Zhu, Hua; Ozkan, Jerome; Wu, Duojia; Masoudi, Simin; Bandara, Rani; Borazjani, Roya N; Willcox, Mark D P

    2012-08-01

    The objective of this study was to determine the bacterial adhesion to various silicone hydrogel lens materials and to determine whether lens wear modulated adhesion. Bacterial adhesion (total and viable cells) of Staphylococcus aureus (31, 38, and ATCC 6538) and Pseudomonas aeruginosa (6294, 6206, and GSU-3) to 10 commercially available different unworn and worn silicone hydrogel lenses was measured. Results of adhesion were correlated to polymer and surface properties of contact lenses. S. aureus adhesion to unworn lenses ranged from 2.8 × 10 to 4.4 × 10 colony forming units per lens. The highest adhesion was to lotrafilcon A lenses, and the lowest adhesion was to asmofilcon A lenses. P. aeruginosa adhesion to unworn lenses ranged from 8.9 × 10 to 3.2 × 10 colony forming units per lens. The highest adhesion was to comfilcon A lenses, and the lowest adhesion was to asmofilcon A and balafilcon A lenses. Lens wear altered bacterial adhesion, but the effect was specific to lens and strain type. Adhesion of bacteria, regardless of genera/species or lens wear, was generally correlated with the hydrophobicity of the lens; the less hydrophobic the lens surface, the greater the adhesion. P. aeruginosa adhered in higher numbers to lenses in comparison with S. aureus strains, regardless of the lens type or lens wear. The effect of lens wear was specific to strain and lens. Hydrophobicity of the silicone hydrogel lens surface influenced the adhesion of bacterial cells.

  19. Human climbing with efficiently scaled gecko-inspired dry adhesives.

    Science.gov (United States)

    Hawkes, Elliot W; Eason, Eric V; Christensen, David L; Cutkosky, Mark R

    2015-01-06

    Since the discovery of the mechanism of adhesion in geckos, many synthetic dry adhesives have been developed with desirable gecko-like properties such as reusability, directionality, self-cleaning ability, rough surface adhesion and high adhesive stress. However, fully exploiting these adhesives in practical applications at different length scales requires efficient scaling (i.e. with little loss in adhesion as area grows). Just as natural gecko adhesives have been used as a benchmark for synthetic materials, so can gecko adhesion systems provide a baseline for scaling efficiency. In the tokay gecko (Gekko gecko), a scaling power law has been reported relating the maximum shear stress σmax to the area A: σmax ∝ A(-1/4). We present a mechanical concept which improves upon the gecko's non-uniform load-sharing and results in a nearly even load distribution over multiple patches of gecko-inspired adhesive. We created a synthetic adhesion system incorporating this concept which shows efficient scaling across four orders of magnitude of area, yielding an improved scaling power law: σmax ∝ A(-1/50). Furthermore, we found that the synthetic adhesion system does not fail catastrophically when a simulated failure is induced on a portion of the adhesive. In a practical demonstration, the synthetic adhesion system enabled a 70 kg human to climb vertical glass with 140 cm(2) of adhesive per hand. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

  20. Ways to improve physical and thermal performance of refractory lining materials

    Directory of Open Access Journals (Sweden)

    Khlystov A.I.

    2017-01-01

    Full Text Available Refractory lining materials, which include ceramic refractories and nonfired heat-resistant concretes, have a very short lifespan during the turnaround time measured in years and sometimes months. Therefore, increasing the service life of thermal generating units by 1.5-2 times will bring significant economic benefits. The main factor that determines the durability of refractory lining materials is the thermal resistance. It is possible to increase the thermal resistance by improving such physical and mechanical properties as strength and density. As for the ceramic refractory performance improvement, such technological methods as their structural and chemical modification by phosphate binder impregnation, as well as introduction of phosphate components into the ceramic batches during the molding process increase, in particular, their thermal stability. The use of aluminous and high-alumina cements contributes to a significant increase of not only strength, but also physical and thermal performance of heat-resistant concretes with different fillers. Switching to the use of chemical binders in the compositions of heat-resistant concretes (liquid glass with effective hardeners; silicate-block and phosphate binders enables to develop high-heat resistant materials which do not soften in a wide range of heating temperatures from 400 °С to 1600 °С. The positive results on increasing the thermal resistance of heat-resistant composites can be obtained by reinforcing them with high temperature fibers.

  1. CAR-T cells and allogeneic hematopoietic stem cell transplantation for relapsed/refractory B-cell acute lymphoblastic leukemia.

    Science.gov (United States)

    Liu, Jun; Zhang, Xi; Zhong, Jiang F; Zhang, Cheng

    2017-10-01

    Relapsed/refractory acute lymphoblastic leukemia (ALL) has a low remission rate after chemotherapy, a high relapse rate and poor long-term survival even when allogeneic hematopoietic stem cell transplantation (allo-HSCT) is performed. Chimeric antigen receptors redirected T cells (CAR-T cells) can enhance disease remission with a favorable outcome for relapsed/refractory ALL, though some cases quickly relapsed after CAR-T cell treatment. Thus, treatment with CAR-T cells followed by allo-HSCT may be the best way to treat relapsed/refractory ALL. In this review, we first discuss the different types of CAR-T cells. We then discuss the treatment of relapsed/refractory ALL using only CAR-T cells. Finally, we discuss the use of CAR-T cells, followed by allo-HSCT, for the treatment of relapsed/refractory ALL.

  2. Rate of primary refractory disease in B and T-cell non-Hodgkin's lymphoma: correlation with long-term survival.

    Directory of Open Access Journals (Sweden)

    Corrado Tarella

    Full Text Available BACKGROUND: Primary refractory disease is a main challenge in the management of non-Hodgkin's Lymphoma (NHL. This survey was performed to define the rate of refractory disease to first-line therapy in B and T-cell NHL subtypes and the long-term survival of primary refractory compared to primary responsive patients. METHODS: Medical records were reviewed of 3,106 patients who had undergone primary treatment for NHL between 1982 and 2012, at the Hematology Centers of Torino and Bergamo, Italy. Primary treatment included CHOP or CHOP-like regimens (63.2%, intensive therapy with autograft (16.9%, or other therapies (19.9%. Among B-cell NHL, 1,356 (47.8% received first-line chemotherapy with rituximab. Refractory disease was defined as stable/progressive disease, or transient response with disease progression within six months. RESULTS: Overall, 690 (22.2% patients showed primary refractory disease, with a higher incidence amongst T-cell compared to B-cell NHL (41.9% vs. 20.5%, respectively, p<0.001. Several other clinico-pathological factors at presentation were variably associated with refractory disease, including histological aggressive disease, unfavorable clinical presentation, Bone Marrow involvement, low lymphocyte/monocyte ration and male gender. Amongst B-cell NHL, the addition of rituximab was associated with a marked reduction of refractory disease (13.6% vs. 26.7% for non-supplemented chemotherapy, p<0.001. Overall, primary responsive patients had a median survival of 19.8 years, compared to 1.3 yr. for refractory patients. A prolonged survival was consistently observed in all primary responsive patients regardless of the histology. The long life expectancy of primary responsive patients was documented in both series managed before and after 2.000. Response to first line therapy resulted by far the most predictive factor for long-term outcome (HR for primary refractory disease: 16.52, p<0.001. CONCLUSION: Chemosensitivity to primary

  3. ADHESIVE SYSTEM AFFECTS REPAIR BOND STRENGTH OF RESIN COMPOSITE

    Directory of Open Access Journals (Sweden)

    Özgür IRMAK

    2017-10-01

    Full Text Available Purpose: This study evaluated the effects of different adhesive systems on repair bond strength of aged resin composites. Materials and Methods: Ninety composite discs were built and half of them were subjected to thermal aging. Aged and non-aged specimens were repaired with resin composite using three different adhesive systems; a two-step self-etch adhesive, a two-step total-etch adhesive and a one-step self-etch adhesive; then they were subjected to shear forces. Data were analyzed statistically. Results: Adhesive type and aging significantly affected the repair bond strengths (p<0.0001. No statistical difference was found in aged composite groups repaired with two-step self- etch or two-step total-etch adhesive. One-step self-etch adhesive showed lower bond strength values in aged composite repair (p<0.0001. Conclusion: In the repair of aged resin composite, two-step self-etch and two-step total-etch adhesives exhibited higher shear bond strength values than that of one-step self-etch adhesive.

  4. Clinical observation on Ahmed glaucoma valve implantation for teenagers with refractory glaucoma

    Directory of Open Access Journals (Sweden)

    Dong-Dao Song

    2016-06-01

    Full Text Available AIM:To observe the clinical effect of Ahmed glaucoma valve(AGVimplantation for teenagers with refractory glaucoma. METHODS: Twenty-seven patients(27 eyeswith refractory glaucoma were treated with AGV implantation in our hospital from October 2012 to October 2014. The patients were followed up for 12mo. The success rate of the operation, postoperative intraocular pressure, the best corrected visual acuity, as well as complications were recorded. RESULTS: The success rate of the operation was 85%. The intraocular pressure of the 27 patients decreased from 48.3±8.3mmHg before operations to 21.4±8.1mmHg(PPCONCLUSION: AGV implantation is characterized by a high success rate, simple operation, less complications and is an effective treatment for refractory glaucoma in adolescents.

  5. Corrosion of K-3 glass-contact refractory in sodium-rich aluminosilicate melts

    International Nuclear Information System (INIS)

    Lu, X.D.; Gan, H.; Buechele, A.C.; Pegg, I.L.

    1999-01-01

    The corrosion of the glass-contact refractory Monofrax K-3 in two sodium-rich aluminosilicate melts has been studied at 1,208 and 1,283 C using a modified ASTM procedure with constant agitation of the melt by air bubbling. The results for the monolithic refractory indicate a fast initial stage involving phase dissolution and transformation and a later passivated stage in which the surface of the refractory has been substantially modified. The composition of the stable spinel phase in the altered layer on monolithic coupons of K-3 is almost identical to the equilibrium composition bracketed by the dissolution of powdered K-3 into under-saturated melts on the other. The temperature and melt shear viscosity were found to have significant effects on the rates of K-3 dissolution and transformation

  6. Melphalan, prednisone, thalidomide and defibrotide in relapsed/refractory multiple myeloma: results of a multicenter phase I/II trial.

    Science.gov (United States)

    Palumbo, Antonio; Larocca, Alessandra; Genuardi, Mariella; Kotwica, Katarzyna; Gay, Francesca; Rossi, Davide; Benevolo, Giulia; Magarotto, Valeria; Cavallo, Federica; Bringhen, Sara; Rus, Cecilia; Masini, Luciano; Iacobelli, Massimo; Gaidano, Gianluca; Mitsiades, Constantine; Anderson, Kenneth; Boccadoro, Mario; Richardson, Paul

    2010-07-01

    Defibrotide is a novel orally bioavailable polydisperse oligonucleotide with anti-thrombotic and anti-adhesive effects. In SCID/NOD mice, defibrotide showed activity in human myeloma xenografts. This phase I/II study was conducted to identify the most appropriate dose of defibrotide in combination with melphalan, prednisone and thalidomide in patients with relapsed and relapsed/refractory multiple myeloma, and to determine its safety and tolerability as part of this regimen. This was a phase I/II, multicenter, dose-escalating, non-comparative, open label study. Oral melphalan was administered at a dose of 0.25 mg/kg on days 1-4, prednisone at a dose of 1.5 mg/kg also on days 1-4 and thalidomide at a dose of 50-100 mg/day continuously. Defibrotide was administered orally at three dose-levels: 2.4, 4.8 or 7.2 g on days 1-4 and 1.6, 3.2, or 4.8 g on days 5-35. Twenty-four patients with relapsed/refractory multiple myeloma were enrolled. No dose-limiting toxicity was observed. In all patients, the complete response plus very good partial response rate was 9%, and the partial response rate was 43%. The 1-year progression-free survival and 1-year overall survival rates were 34% and 90%, respectively. The most frequent grade 3-4 adverse events included neutropenia, thrombocytopenia, anemia and fatigue. Deep vein thrombosis was reported in only one patient. This combination of melphalan, prednisone and thalidomide together with defibrotide showed anti-tumor activity with a favorable tolerability. The maximum tolerated dose of defibrotide was identified as 7.2 g p.o. on days 1-4 followed by 4.8 g p.o. on days 5-35. Further trials are needed to confirm the role of this regimen and to evaluate the combination of defibrotide with new drugs.

  7. Designing Hydrogel Adhesives for Corneal Wound Repair

    Science.gov (United States)

    Grinstaff, Mark W.

    2013-01-01

    Today, corneal wounds are repaired using nylon sutures. Yet there are a number of complications associated with suturing the cornea, and thus there is interest in an adhesive to replace or supplement sutures in the repair of corneal wounds. We are designing and evaluating corneal adhesives prepared from dendrimers – single molecular weight, highly branched polymers. We have explored two strategies to form these ocular adhesives. The first involves a photocrosslinking reaction and the second uses a peptide ligation reactions to couple the individual dendrimers together to from the adhesive. These adhesives were successfully used to repair corneal perforations, close the flap produced in a LASIK procedure, and secure a corneal transplant. PMID:17889330

  8. A retrospective study on the management of patients with rituximab refractory follicular lymphoma.

    Science.gov (United States)

    Solal-Céligny, Philippe; Leconte, Pierre; Bardet, Aurélie; Hernandez, Juana; Troussard, Xavier

    2018-01-01

    Given that there are currently no clear recommendations regarding therapeutic options for rituximab refractory/relapsed follicular lymphoma patients, this study aimed to describe the real-life management of patients with refractory follicular lymphoma after systemic rituximab-containing regimens (rFL), and rFL patient characteristics. In this retrospective, national, multicentre study, descriptive analyses were mainly performed according to rituximab-containing regimen at rFL diagnosis [rituximab monotherapy (R-MONO), rituximab + chemotherapy (R-COMBO), and ongoing rituximab maintenance (R-MAINTAIN)]. The 459 analysed patients experienced rituximab-refractoriness between October 2013 and September 2015: R-MONO: 58 (13%), R-COMBO: 197 (43%), R-MAINTAIN: 204 (44%). Post-refractoriness strategies were heterogeneous: idelalisib ± rituximab (22%), without anti-lymphoma treatment (21%), rituximab-chemotherapy (21%) and stem cell transplantation (18%). Rituximab was continued in combination in 41% of cases. Chosen strategies varied according to patient age (without anti-lymphoma treatment: 28% of patients if ≥65 years vs. 12% if management and for the design of clinical trials in these patients. © 2017 John Wiley & Sons Ltd.

  9. New applications and novel processing of refractory metal alloys

    International Nuclear Information System (INIS)

    Briant, C.L.

    2001-01-01

    Refractory metals have often been limited in their application because of their propensity to oxidize and to undergo a loos of yield strength at elevated temperatures. However, recent developments in both processing and alloy composition have opened the possibility that these materials might be used in structural applications that were not considered possible in the past. At the same time, the use of refractory metals in the electronics industry is growing, particularly with the use of tantalum as a diffusion barrier for copper metallization. Finally, the application of grain boundary engineering to the problem of intergranular fracture in these materials may allow processes to be developed that will produce alloys with a greater resistance to fracture. (author)

  10. Classical management of refractory adult immune (idiopathic) thrombocytopenic purpura.

    Science.gov (United States)

    McMillan, R

    2002-03-01

    Treatment of chronic immune (idiopathic) thrombocytopenic purpura with corticosteroids and/or splenectomy results in safe platelet counts in over 70% of patients without additional treatment. Therapy of patients who are refractory to these two treatments may be difficult. The treatment approach to refractory ITP patients, described in this report, is arbitrarily divided into four levels: levels 1 through 3 represent treatments with increasing side effects; level 4 therapy may be tried when the others have failed. Patients undergoing these treatments may require concomitant intravenous gammaglobulin, high-dose corticosteroids or platelets, to maintain the platelet count in the setting of mucosal bleeding or severe thrombocytopenia. Copyright 2002, Elsevier Science Ltd. All rights reserved.

  11. Scaling Principles for Understanding and Exploiting Adhesion

    Science.gov (United States)

    Crosby, Alfred

    A grand challenge in the science of adhesion is the development of a general design paradigm for adhesive materials that can sustain large forces across an interface yet be detached with minimal force upon command. Essential to this challenge is the generality of achieving this performance under a wide set of external conditions and across an extensive range of forces. Nature has provided some guidance through various examples, e.g. geckos, for how to meet this challenge; however, a single solution is not evident upon initial investigation. To help provide insight into nature's ability to scale reversible adhesion and adapt to different external constraints, we have developed a general scaling theory that describes the force capacity of an adhesive interface in the context of biological locomotion. We have demonstrated that this scaling theory can be used to understand the relative performance of a wide range of organisms, including numerous gecko species and insects, as well as an extensive library of synthetic adhesive materials. We will present the development and testing of this scaling theory, and how this understanding has helped guide the development of new composite materials for high capacity adhesives. We will also demonstrate how this scaling theory has led to the development of new strategies for transfer printing and adhesive applications in manufacturing processes. Overall, the developed scaling principles provide a framework for guiding the design of adhesives.

  12. Microleakage comparison of three types of adhesive systems versus GIC-based adhesive in class V composite restorations

    Directory of Open Access Journals (Sweden)

    Mostafa Sadeghi

    2016-06-01

    Full Text Available Background and aims: New dentin bonding agents and techniques have been developed to reduce microleakage and create higher bond strength. This in-vitro study compared the microleakage of three resin-based adhesives versus a GIC-based adhesive on class V composite restorations.  Materials and Methods: Class V cavities were prepared on the buccal surfaces of 72 sound premolars, randomly assigned to six groups (n=12 and treated as follows: without any treatment (negative control group; total-etch (OptiBond Solo Plus; two-step self-etch (OptiBond XTR; one-step self-etch (OptiBond All-in-One and GIC-based adhesive (Fuji bond LC with pre-cure and co-cure techniques. The treated cavities were filled with a micro-hybrid resin composite (Point 4, Kerr. Following finishing and polishing procedures, the specimens were placed in 100% humidity, stored in distilled water, thermocycled and then immersed in a methylene blue, sectioned, evaluated for microleakage and scored on a 0 to 3 ordinal scale.  Results: None of the adhesives tested were capable of completely eliminating marginal microleakage. There were statistically significant differences among the test groups at occlusal margins; but at cervical margins were not. The Fuji Bond LC with co-cure and control groups had significantly greater microleakage scores at the occlusal margins. At the cervical margins, the bonded restorations with OptiBond XTR and OptiBond All-in-One adhesives presented significantly lower microleakage scores. Also, there were no significant differences between the resin adhesive groups both at occlusal and cervical margins. The microleakage scores at the cervical margins were markedly higher than the occlusal margins in the groups bonded with OptiBond Solo Plus and Fuji Bond LC with pre-cure. The differences between Fuji Bond LC adhesive with pre-cure and co-cure techniques were significant. Conclusion: This study encourages application of the Fuji bond LC adhesive with pre

  13. Refractory Septic Shock Treated with Nephrectomy under the Support of Extracorporeal Membrane Oxygenation

    Directory of Open Access Journals (Sweden)

    Young Kun Lee

    2015-08-01

    Full Text Available Conventional medical therapies have not been very successful in treating adults with refractory septic shock. The effects of direct hemoperfusion using polymyxin B and veno-arterial extracorporeal membrane oxygenation (ECMO for refractory septic shock remain uncertain. A 66-year-old man was admitted to the emergency department and suffered from sepsis-induced hemodynamic collapse. For hemodynamic improvement, we performed direct hemoperfusion using polymyxin B. Computed tomography scan of this patient revealed emphysematous pyelonephritis (EPN, for which he underwent emergent nephrectomy with veno-arterial ECMO support. To the best of our knowledge, this is the first report of successful treatment of EPN with refractory septic shock using polymyxin B hemoperfusion and nephrectomy under the support of ECMO.

  14. Syndecan-4 and focal adhesion function

    DEFF Research Database (Denmark)

    Woods, A; Couchman, J R

    2001-01-01

    Two groups have now reported the viability of mice that lack syndecan-4. These mice have wound healing/angiogenesis problems, and fibroblasts from these animals differ in adhesion and migration from normal. This is consistent with recent in vitro data indicating a need for signaling via syndecan-4...... for focal adhesion formation, and reports that overexpression of proteins that bind syndecan-4 can modify cell adhesion and migration....

  15. Adhesion of silver films to ion-bombarded alumina

    International Nuclear Information System (INIS)

    Erck, R.A.; Fenske, G.R.

    1990-01-01

    This paper reports on silver films deposited on alumina substrates using ion bombardment. Adhesion strength was measured as a function of deposition conditions, sputter-cleaning time, and bombarding ion species, using a pull-type adhesion tester. Argon- and argon/oxygen-ion sputtering produced large increases in adhesion strength, with the greatest increases occurring for oxygen-ion bombardment. Adhesion strength increased monotonically as a function of ion sputtering time. At a given deposition rate, further enhancement of adhesion is seen with concurrent ion bombardment

  16. Iatrogenic colorectal Kaposi sarcoma complicating a refractory ...

    African Journals Online (AJOL)

    Kaposi sarcoma is a mesenchymal tumor associated to a human herpes virus-8. It often occurs in human immunodeficiency virus-positive subjects. Colorectal localization is rare. We report the case of a colorectal Kaposi sarcoma complicating a refractory ulcerative colitis treated with surgery after the failure of ...

  17. Photovoltaic module with adhesion promoter

    Science.gov (United States)

    Xavier, Grace

    2013-10-08

    Photovoltaic modules with adhesion promoters and methods for fabricating photovoltaic modules with adhesion promoters are described. A photovoltaic module includes a solar cell including a first surface and a second surface, the second surface including a plurality of interspaced back-side contacts. A first glass layer is coupled to the first surface by a first encapsulating layer. A second glass layer is coupled to the second surface by a second encapsulating layer. At least a portion of the second encapsulating layer is bonded directly to the plurality of interspaced back-side contacts by an adhesion promoter.

  18. Efficacy and Safety of Rituximab in Children with Refractory Nephrotic Syndrome; A Multicenter Clinical Trial

    Directory of Open Access Journals (Sweden)

    Yo Han Ahn

    2014-06-01

    Conclusions: In this interim analysis of clinical trial to evaluate the efficacy and safety of RTX in children with refractory NS, RTX treatment for refractory NS was safe and effective, especially in patients with DNS.

  19. Evaluation of nutritional status in children with refractory epilepsy.

    Science.gov (United States)

    Bertoli, S; Cardinali, S; Veggiotti, P; Trentani, C; Testolin, G; Tagliabue, A

    2006-04-26

    children affected by refractory epilepsy could be at risk of malnutrition because of feeding difficulties (anorexia, chewing, swallowing difficulties or vomiting) and chronic use of anticonvulsants, which may affect food intake and energy metabolism. Moreover, their energy requirement may be changed as their disabilities would impede normal daily activities. The aim of the present study was to evaluate nutritional status, energy metabolism and food intake in children with refractory epilepsy. 17 children with refractory epilepsy (13 boys and 4 girls; mean age 9 +/- 3,2 years; Body Mass Index 15,7 +/- 3,6) underwent an anthropometric assessment, body composition evaluation by dual-energy X-ray absorptiometry, detailed dietetic survey and measurement of resting energy expenditure by indirect calorimetry. Weight-for-age, height-for-age (stunting) and weight-for-height (wasting) were estimated compared to those of a reference population of the same age. 40% of children were malnourished and 24% were wasted. The nutritional status was worse in the more disabled children. Dietary intake resulted unbalanced (18%, 39%, 43% of total daily energy intake derived respectively from protein, lipid and carbohydrate). Adequacy index [nutrient daily intake/recommended allowance (RDA) x 100] was nutritional assessment and management as part of their overall care.

  20. Adalimumab for the treatment of refractory noninfectious paediatric uveitis.

    Science.gov (United States)

    Muñoz-Gallego, Alicia; Barral, Estefanía; Enríquez, Eugenia; Tejada, Pilar; Barceló, Ana; de Inocencio, Jaime

    2017-06-01

    To report the experience of our center with the use of adalimumab (ADA) for the treatment of severe refractory noninfectious paediatric uveitis. The study is a retrospective case series of all paediatric patients with refractory uveitis who were treated with ADA at the Paediatric Uveitis Unit of our center from 2008 to 2015. We present 12 patients (6 Juvenile idiopathic arthritis-associated uveitis, 4 idiopathic panuveitis, 1 early-onset sarcoidosis-associated panuveitis, and 1 intermediate uveitis), with uveitis in 19/24 eyes. Once ADA therapy was started, all the patients presented improved activity according to Standardization of Uveitis Nomenclature (SUN) criteria. Nine out of the 12 patients had structural damage before ADA could be started: cataract (n = 4), glaucoma (n = 2), cystic macular edema (n = 1), exudative retinal detachment (n = 1), and optic disk edema (n = 5). Visual acuity improved or maintained stable in 17/19 affected eyes, and only 2 eyes decreased its visual acuity because of structural damage, which was already present before ADA therapy. In our experience, ADA presents a good safety profile and is efficacious in the treatment of paediatric patients with different forms of refractory noninfectious uveitis.

  1. Evaluation of nutritional status in children with refractory epilepsy

    Science.gov (United States)

    Bertoli, S; Cardinali, S; Veggiotti, P; Trentani, C; Testolin, G; Tagliabue, A

    2006-01-01

    Background children affected by refractory epilepsy could be at risk of malnutrition because of feeding difficulties (anorexia, chewing, swallowing difficulties or vomiting) and chronic use of anticonvulsants, which may affect food intake and energy metabolism. Moreover, their energy requirement may be changed as their disabilities would impede normal daily activities. The aim of the present study was to evaluate nutritional status, energy metabolism and food intake in children with refractory epilepsy. Methods 17 children with refractory epilepsy (13 boys and 4 girls; mean age 9 ± 3,2 years; Body Mass Index 15,7 ± 3,6) underwent an anthropometric assessment, body composition evaluation by dual-energy X-ray absorptiometry, detailed dietetic survey and measurement of resting energy expenditure by indirect calorimetry. Weight-for-age, height-for-age (stunting) and weight-for-height (wasting) were estimated compared to those of a reference population of the same age. Results 40% of children were malnourished and 24% were wasted. The nutritional status was worse in the more disabled children. Dietary intake resulted unbalanced (18%, 39%, 43% of total daily energy intake derived respectively from protein, lipid and carbohydrate). Adequacy index [nutrient daily intake/recommended allowance (RDA) × 100] was nutritional assessment and management as part of their overall care. PMID:16640779

  2. Refractory metal particles in refractory inclusions in the Allende meteorite

    International Nuclear Information System (INIS)

    Fuchs, L.H.; Blander, M.

    1980-01-01

    An examination of refractory metal particles in five calcium-aluminum-rich inclusions in the Allende meteorite indicates a complex variety of compositions and large departures from equilibrium. These particles appear to have been primordial condensates which were isolated from the nebula and from each other at different times by cocondensing oxides. Selective diffusion and/or oxidation of the more oxidizable metals (Mo, W, Fe and Ni), phase segregations into different alloy phases (fcc, bcc, hcp and perhaps ordered phases) and the formation of metastable condensates appears to have been involved in the modification of these materials to their present state. Only a small fraction of our observations cannot be reconciled with this picture because of a lack of knowledge of some of the phase equilibria which might have bee involved

  3. Closed-Cycle Hydrogen-Oxygen Regenerative Fuel Cell at the NASA Glenn Research Center-An Update

    Science.gov (United States)

    Bents, David J.; Chang, Bei-Jiann; Johnson, Donald W.; Garcia, Christopher P.

    2008-01-01

    The closed cycle hydrogen-oxygen proton exchange membrane (PEM) regenerative fuel cell (RFC) at the NASA Glenn Research Center has demonstrated multiple back-to-back contiguous cycles at rated power and round-trip efficiencies up to 52 percent. It is the first fully closed cycle RFC ever demonstrated. (The entire system is sealed; nothing enters or escapes the system other than electrical power and heat.) During fiscal year fiscal year (FY) FY06 to FY07, the system s numerous modifications and internal improvements focused on reducing parasitic power, heat loss, and noise signature; increasing its functionality as an unattended automated energy storage device; and in-service reliability.

  4. Variable-Speed Power-Turbine Research at Glenn Research Center

    Science.gov (United States)

    Welch, Gerard E.; McVetta, Ashlie B.; Stevens, Mark A.; Howard, Samuel A.; Giel, Paul W.; Ameri, Ali, A.; To, Waiming; Skoch, Gary J.; Thurman, Douglas R.

    2012-01-01

    The main rotors of the NASA Large Civil Tilt-Rotor (LCTR) notional vehicle operate over a wide speed-range, from 100 percent at takeoff to 54 percent at cruise. The variable-speed power turbine (VSPT) offers one approach by which to effect this speed variation. VSPT aerodynamics challenges include high work factors at cruise, wide (40 to 60 ) incidence-angle variations in blade and vane rows over the speed range, and operation at low Reynolds numbers. Rotordynamics challenges include potential responsiveness to shaft modes within the 50 percent VSPT speed-range. A research effort underway at NASA Glenn Research Center, intended to address these key aerodynamic and rotordynamic challenges, is described. Conceptual design and 3-D multistage RANS and URANS analyses, conducted internally and under contract, provide expected VSPT sizing, stage-count, performance and operability information, and maps for system studies. Initial steps toward experimental testing of incidence-tolerant blading in a transonic linear cascade are described, and progress toward development/improvement of a simulation capability for multistage turbines with low Reynolds number transitional flow is summarized. Preliminary rotordynamics analyses indicate that viable concept engines with 50 percent VSPT shaft-speed range. Assessments of potential paths toward VSPT component-level testing are summarized.

  5. Sub-micrometer refractory carbonaceous particles in the polar stratosphere

    Science.gov (United States)

    Schütze, Katharina; Wilson, James Charles; Weinbruch, Stephan; Benker, Nathalie; Ebert, Martin; Günther, Gebhard; Weigel, Ralf; Borrmann, Stephan

    2017-10-01

    Eleven particle samples collected in the polar stratosphere during SOLVE (SAGE III Ozone loss and validation experiment) from January until March 2000 were characterized in detail by high-resolution transmission and scanning electron microscopy (TEM/SEM) combined with energy-dispersive X-ray microanalysis. A total of 4202 particles (TEM = 3872; SEM = 330) were analyzed from these samples, which were collected mostly inside the polar vortex in the altitude range between 17.3 and 19.9 km. Particles that were volatile in the microscope beams contained ammonium sulfates and hydrogen sulfates and dominated the samples. Some particles with diameters ranging from 20 to 830 nm were refractory in the electron beams. Carbonaceous particles containing additional elements to C and O comprised from 72 to 100 % of the refractory particles. The rest were internal mixtures of these materials with sulfates. The median number mixing ratio of the refractory particles, expressed in units of particles per milligram of air, was 1.1 (mg air)-1 and varied between 0.65 and 2.3 (mg air)-1. Most of the refractory carbonaceous particles are completely amorphous, a few of the particles are partly ordered with a graphene sheet separation distance of 0.37 ± 0.06 nm (mean value ± standard deviation). Carbon and oxygen are the only detected major elements with an atomic O/C ratio of 0.11 ± 0.07. Minor elements observed include Si, S, Fe, Cr and Ni with the following atomic ratios relative to C: Si/C: 0.010 ± 0.011; S/C: 0.0007 ± 0.0015; Fe/C: 0.0052 ± 0.0074; Cr/C: 0.0012 ± 0.0017; Ni/C: 0.0006 ± 0.0011 (all mean values ± standard deviation).High-resolution element distribution images reveal that the minor elements are distributed within the carbonaceous matrix; i.e., heterogeneous inclusions are not observed. No difference in size, nanostructure and elemental composition was found between particles collected inside and outside the polar vortex. Based on chemistry and nanostructure

  6. Overview of CMC (Ceramic Matrix Composite) Research at the NASA Glenn Research Center

    Science.gov (United States)

    Kiser, J. Douglas; Grady, Joseph E.; Bhatt, Ramakrishna T.; Wiesner, Valerie L.; Zhu, Dongming

    2016-01-01

    In support of NASAs Aeronautics Research Mission, the Glenn Research Center has developed and assessed various constituents for a high temperature (2700F) SiCSiC CMC system for turbine engine applications. Combinations of highly creep-resistant SiC fibers, advanced 3D weaves, durable environmental barrier coatings (EBCs), and a 2700F-capable hybrid SiC matrix are being developed evaluated. The resulting improvements in CMC mechanical properties and durability will be summarized. The development and validation of models for predicting the effects of the environment on the durability of CMCs and EBCs and other operating-environment challenges including the effect of CMAS (calcium magnesium aluminosilicate) degradation of EBCs will be discussed. Progress toward the development of CMC joining technology for 2400F joint applications will also be reviewed.

  7. Do uniform tangential interfacial stresses enhance adhesion?

    Science.gov (United States)

    Menga, Nicola; Carbone, Giuseppe; Dini, Daniele

    2018-03-01

    We present theoretical arguments, based on linear elasticity and thermodynamics, to show that interfacial tangential stresses in sliding adhesive soft contacts may lead to a significant increase of the effective energy of adhesion. A sizable expansion of the contact area is predicted in conditions corresponding to such scenario. These results are easily explained and are valid under the assumptions that: (i) sliding at the interface does not lead to any loss of adhesive interaction and (ii) spatial fluctuations of frictional stresses can be considered negligible. Our results are seemingly supported by existing experiments, and show that frictional stresses may lead to an increase of the effective energy of adhesion depending on which conditions are established at the interface of contacting bodies in the presence of adhesive forces.

  8. Wetting of refractory metals with copper base alloys

    International Nuclear Information System (INIS)

    Anikeev, E.F.; Kostikov, V.I.; Chepelenko, V.N.; Batov, V.M.

    1978-01-01

    The effect is studied of phosphorus upon the wetting of molybdenum, niobium and tantalum by an alloy of the system copper-silver (10%) as a function of contact time and phosphorus concentration. Experiments have been conducted in vacuum of 5x10 -4 mm Hg at 900 deg C. It is established that the introduction of phosphorus into a copper-silver alloy improves the wetting of molybdenum, niobium and tantalum. Formation of intermetallic compounds on the alloy-refractory metal interface can be avoided by adjusting the time of contact of the solder with molybdenum, niobium and tantalum. As a solder with 2.9% phosphorus spreads well over copper, it is suggested to use said solder for brazing copper and the investigated refractory metals in items intended for service at temperatures of up to 600 deg C

  9. Structural Evaluation of the RSRM Nozzle Replacement Adhesive

    Science.gov (United States)

    Batista-Rodriguez, A.; McLennan, M. L.; Palumbos, A. V.; Richardson, D. E.

    1999-01-01

    This paper describes the structural performance evaluation of a replacement adhesive for the Reusable Solid Rocket Motor (RSRM) nozzle utilizing finite element analysis. Due to material obsolescence and industrial safety issues, the two current structural adhesives, EA 913 and EA 946 are to be replaced with a new adhesive. TIGA 321. The structural evaluation in support of the adhesive replacement effort includes residual stress, transportation, and flight analyses. Factors of safety are calculated using the stress response from each analysis. The factors of safety are used as the limiting criteria to compare the replacement adhesive against the current adhesives. Included in this paper are the analytical approach, assumptions and modeling techniques as well as the results of the evaluation. An important factor to the evaluation is the similarity in constitutive material properties (elastic modulus and Poisson's ratio) between TIGA 321 and EA 913. This similarity leads to equivalent material response from the two adhesives. However, TIGA 321 surpasses EA 913's performance due to higher material capabilities. Conversely, the change in stress response from EA 946 to TIGA 321 is more apparent: this is primarily attributed to the difference in the modulii of the two adhesives, which differ by two orders of magnitude. The results of the bondline evaluation indicate that the replacement adhesive provides superior performance than the current adhesives with only minor exceptions. Furthermore, TIGA 321 causes only a minor chance in the response of the phenolic and metal components.

  10. Refractory compounds for repairing coke-oven brickwork

    Energy Technology Data Exchange (ETDEWEB)

    Hanganu, M.; Dragomir, C. (and others)

    1984-01-01

    A number of refractory compounds are presented, based on aluminium phosphate, phosphoric acid, sodium silicate and fire-clay and mullitic zirconium mastic, including their composition, properties and application (by impregnation, spray application or pouring), which are suitable for repairing various types of coke-oven brickwork. The results obtained are given.

  11. Uncertainty Analysis of the NASA Glenn 8x6 Supersonic Wind Tunnel

    Science.gov (United States)

    Stephens, Julia; Hubbard, Erin; Walter, Joel; McElroy, Tyler

    2016-01-01

    This paper presents methods and results of a detailed measurement uncertainty analysis that was performed for the 8- by 6-foot Supersonic Wind Tunnel located at the NASA Glenn Research Center. The statistical methods and engineering judgments used to estimate elemental uncertainties are described. The Monte Carlo method of propagating uncertainty was selected to determine the uncertainty of calculated variables of interest. A detailed description of the Monte Carlo method as applied for this analysis is provided. Detailed uncertainty results for the uncertainty in average free stream Mach number as well as other variables of interest are provided. All results are presented as random (variation in observed values about a true value), systematic (potential offset between observed and true value), and total (random and systematic combined) uncertainty. The largest sources contributing to uncertainty are determined and potential improvement opportunities for the facility are investigated.

  12. Treatment of refractory/relapsed adult acute lymphoblastic leukemia with bortezomib- based chemotherapy

    Directory of Open Access Journals (Sweden)

    Zhao J

    2015-06-01

    Full Text Available Junmei Zhao,* Chao Wang,* Yongping Song, Yuzhang Liu, Baijun FangHenan Key Lab of Experimental Haematology, Henan Institute of Haematology, Henan Tumor Hospital, Zhengzhou University, Zhengzhou, People’s Republic of China  *These authors contributed equally to this work Abstract: Nine pretreated patients aged >19 years with relapsed/refractory acute lymphoblastic leukemia (ALL were treated with a combination of bortezomib plus chemotherapy before allogeneic hematopoietic stem cell transplantation (allo-HSCT. Eight (88.9% patients, including two Philadelphia chromosome-positive ALL patients, achieved a complete remission. Furthermore, the evaluable patients have benefited from allo-HSCT after response to this reinduction treatment. We conclude that bortezomib-based chemotherapy was highly effective for adults with refractory/relapsed ALL before allo-HSCT. Therefore, this regimen deserves a larger series within prospective trials to confirm these results. Keywords: acute lymphoblastic leukemia, refractory, relapsed, bortezomib

  13. Evaluation of high temperature structural adhesives for extended service

    Science.gov (United States)

    Hendricks, C. L.; Hill, S. G.

    1984-01-01

    High temperature stable adhesive systems were evaluated for potential Supersonic Cruise Research (SCR) vehicle applications. The program was divided into two major phases: Phase I 'Adhesive Screening' evaluated eleven selected polyimide (PI) and polyphenylquinoxaline (PPQ) adhesive resins using eight different titanium (6Al-4V) adherend surface preparations; Phase II 'Adhesive Optimization and Characterization' extensively evaluated two adhesive systems, selected from Phase I studies, for chemical characterization and environmental durability. The adhesive systems which exhibited superior thermal and environmental bond properties were LARC-TPI polyimide and polyphenylquinoxaline both developed at NASA Langley. The latter adhesive system did develop bond failures at extended thermal aging due primarily to incompatibility between the surface preparation and the polymer. However, this study did demonstrate that suitable adhesive systems are available for extended supersonic cruise vehicle design applications.

  14. Long-term effects of electrical neurostimulation in patients with unstable angina : Refractory to conventional therapies

    NARCIS (Netherlands)

    de Vries, Jessica; DeJongste, Mike J. L.; Zijlstra, Felix; Staal, Michiel

    2007-01-01

    Background. Patients with unstable angina pectoris may become refractory to conventional therapies. Electrical neurostimulation with transcutaneous electrical stimulation and/or spinal cord stimulation has been shown to be effective for patients with refractory unstable angina pectoris in hospital

  15. Degradation of Alumina and Magnesia Chrome refractory bricks in Portland cement kiln – Corrected version*

    Directory of Open Access Journals (Sweden)

    Ben Addi K.

    2014-05-01

    Full Text Available In cement plants, the refractory products are particularly confronted to partially liquid oxide phases at temperature ranging between 900°C and 1700°C. All constituents of these products have to resist not only to thermal constraints, but also to the thermochemical solicitations which result from contact material/coating. In order to study the phenomenon of degradation of refractory bricks in cement kilns and to identify the causes of their degradation, we proceed to the examination of industrial cases in cement kiln. Many chemical tests of the degraded refractory bricks have been done and the results acquired were compared to the ones not used. The analysis of the results is doing using different techniques (Loss of ignition, X-ray Fluorescence, X-ray Diffraction. The results show that the degradation of the used bricks in the clinkering and cooling zone is due to the infiltration of aggressive elements such us sulphur, alkali (Na2O, K2O .... The chemical interaction between the Portland clinker phases and refractory material has also an importance on the stability of the coating and consequently on the life of the refractories.

  16. Bulk Vitrification Castable Refractory Block Protection Study

    Energy Technology Data Exchange (ETDEWEB)

    Hrma, Pavel R.; Bagaasen, Larry M.; Beck, Andrew E.; Brouns, Thomas M.; Caldwell, Dustin D.; Elliott, Michael L.; Matyas, Josef; Minister, Kevin BC; Schweiger, Michael J.; Strachan, Denis M.; Tinsley, Bronnie P.; Hollenberg, Glenn W.

    2005-05-01

    Bulk vitrification (BV) was selected for a pilot-scale test and demonstration facility for supplemental treatment to accelerate the cleanup of low-activity waste (LAW) at the Hanford U.S. DOE Site. During engineering-scale (ES) tests, a small fraction of radioactive Tc (and Re, its nonradioactive surrogate) were transferred out of the LAW glass feed and molten LAW glass, and deposited on the surface and within the pores of the castable refractory block (CRB). Laboratory experiments were undertaken to understand the mechanisms of the transport Tc/Re into the CRB during vitrification and to evaluate various means of CRB protection against the deposition of leachable Tc/Re. The tests used Re as a chemical surrogate for Tc. The tests with the baseline CRB showed that the molten LAW penetrates into CRB pores before it converts to glass, leaving deposits of sulfates and chlorides when the nitrate components decompose. Na2O from the LAW reacts with the CRB to create a durable glass phase that may contain Tc/Re. Limited data from a single CRB sample taken from an ES experiment indicate that, while a fraction of Tc/Re is present in the CRB in a readily leachable form, most of the Tc/Re deposited in the refractory is retained in the form of a durable glass phase. In addition, the molten salts from the LAW, mainly sulfates, chlorides, and nitrates, begin to evaporate from BV feeds at temperatures below 800 C and condense on solid surfaces at temperatures below 530 C. Three approaches aimed at reducing or preventing the deposition of soluble Tc/Re within the CRB were proposed: metal lining, sealing the CRB surface with a glaze, and lining the CRB with ceramic tiles. Metal liners were deemed unsuitable because evaluations showed that they can cause unacceptable distortions of the electric field in the BV system. Sodium silicate and a low-alkali borosilicate glaze were selected for testing. The glazes slowed down molten salt condensate penetration, but did little to reduce the

  17. Adhesion of rhodium films on metallic substrates

    International Nuclear Information System (INIS)

    Marot, L.; Covarel, G.; Tuilier, M.-H.; Steiner, R.; Oelhafen, P.

    2008-01-01

    Rhodium coated metallic films were prepared by magnetron sputtering on metallic substrates. All films were elaborated in same conditions on copper, molybdenum and stainless steel. Adhesion strength tests were carried out by scratch test. The results reveal that the adhesion strength between the film and the substrate is influenced by the hardness of the substrate. Increase of deposition temperature improves the adhesion of the coating. In addition, pre-treatment of substrates by a filtered cathodic vacuum arc and the layer thickness have has some effects on the final adhesion strength

  18. Adhesion of rhodium films on metallic substrates

    Energy Technology Data Exchange (ETDEWEB)

    Marot, L. [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland)], E-mail: laurent.marot@unibas.ch; Covarel, G.; Tuilier, M.-H. [Laboratoire Mecanique, Materiaux et Procedes de Fabrication, Pole STIC-SPI-Math 61 rue Albert Camus, Universite de Haute-Alsace, F-68093 - Mulhouse Cedex (France); Steiner, R.; Oelhafen, P. [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland)

    2008-09-01

    Rhodium coated metallic films were prepared by magnetron sputtering on metallic substrates. All films were elaborated in same conditions on copper, molybdenum and stainless steel. Adhesion strength tests were carried out by scratch test. The results reveal that the adhesion strength between the film and the substrate is influenced by the hardness of the substrate. Increase of deposition temperature improves the adhesion of the coating. In addition, pre-treatment of substrates by a filtered cathodic vacuum arc and the layer thickness have has some effects on the final adhesion strength.

  19. Anti-adhesive properties of fish tropomyosins

    DEFF Research Database (Denmark)

    Vejborg, Rebecca Munk; Bernbom, Nete; Gram, Lone

    2008-01-01

    Aims: We have recently found that preconditioning of stainless steel surfaces with an aqueous fish muscle extract can significantly impede bacterial adhesion. The purpose of this study was to identify and characterize the primary components associated with this bacteria-repelling effect. Methods...... to the formation of a proteinaceous conditioning film composed primarily of fish tropomyosins. These fibrous proteins formed a considerable anti-adhesive conditioning layer on and reduced bacterial adhesion to several different materials including polystyrene, vinyl plastic, stainless steel and glass. The protein...... the importance of substratum's physiochemical properties and exposure time with regards to protein adsorption/elution efficiency and subsequent bacterial adhesion. Significance and Impact of the Study: Fish tropomyosin-coatings could potentially offer a nontoxic and relatively inexpensive measure of reducing...

  20. Focal adhesion interactions with topographical structures: a novel method for immuno-SEM labelling of focal adhesions in S-phase cells.

    Science.gov (United States)

    Biggs, M J P; Richards, R G; Wilkinson, C D W; Dalby, M J

    2008-07-01

    Current understanding of the mechanisms involved in osseointegration following implantation of a biomaterial has led to adhesion quantification being implemented as an assay of cytocompatibility. Such measurement can be hindered by intra-sample variation owing to morphological changes associated with the cell cycle. Here we report on a new scanning electron microscopical method for the simultaneous immunogold labelling of cellular focal adhesions and S-phase nuclei identified by BrdU incorporation. Prior to labelling, cellular membranes are removed by tritonization and antigens of non-interest blocked by serum incubation. Adhesion plaque-associated vinculin and S-phase nuclei were both separately labelled with a 1.4 nm gold colloid and visualized by subsequent colloid enhancement via silver deposition. This study is specifically concerned with the effects microgroove topographies have on adhesion formation in S-phase osteoblasts. By combining backscattered electron (BSE) imaging with secondary electron (SE) imaging it was possible to visualize S-phase nuclei and the immunogold-labelled adhesion sites in one energy 'plane' and the underlying nanotopography in another. Osteoblast adhesion to these nanotopographies was ascertained by quantification of adhesion complex formation.