Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 2. Commercial waste forms, packaging and projections for preconceptual repository design studies

International Nuclear Information System (INIS)

1978-04-01

This volume, Y/OWI/TM-36/2, ''Commercial Waste Forms, Packaging and Projections for Preconceptual Repository Design Studies,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This volume contains the data base for waste forms, packages, and projections from the commercial waste defined by the Office of Waste Isolation in ''Nuclear Waste Projections and Source Term Data for FY 1977,'' Y/OWI/TM-34. Also, as an alternative data base for repository design and analysis, waste forms, packages, and projections for commercial waste defined by Battelle Pacific Northwest Laboratory (BPNL) have been included. This data base consists of a reference case for use in the alternative design study and a definition of combustible wastes for use in mine fire and hydrogen generation analyses

Tectonic risk forecasting through expert elicitation for geological repositories: the TOPAZ project

Energy Technology Data Exchange (ETDEWEB)

Goto, Junichi [NUMO, Tokyo (Japan); Kawamura, Hideki [Obayashi Corporation, Tokyo (Japan); Chapman, Neil [MCM Consulting, Baden (Switzerland)

2013-07-01

This paper describes the development of a probabilistic methodology for the evaluation of tectonic hazards to geological repositories in Japan. The approach is a development of NUMO's ITM methodology, which produced probabilistic hazard maps for volcanism and rock deformation for periods up to about 100,000 years in a set of Case Studies that covered a large area of the country. To address potential regulatory requirements, the TOPAZ project has extended the ITM methodology to look into the period between 100,000 and 1 million years, where significant uncertainties begin to emerge about the tectonic framework within which quantitative forecasting can be made. Part of this methodology extension has been to adopt expert elicitation techniques to capture differing expert views as a means of addressing such uncertainties. This paper briefly outlines progress in this development work to date. (authors)

Tectonic risk forecasting through expert elicitation for geological repositories: the TOPAZ project

International Nuclear Information System (INIS)

Goto, Junichi; Kawamura, Hideki; Chapman, Neil

2013-01-01

This paper describes the development of a probabilistic methodology for the evaluation of tectonic hazards to geological repositories in Japan. The approach is a development of NUMO's ITM methodology, which produced probabilistic hazard maps for volcanism and rock deformation for periods up to about 100,000 years in a set of Case Studies that covered a large area of the country. To address potential regulatory requirements, the TOPAZ project has extended the ITM methodology to look into the period between 100,000 and 1 million years, where significant uncertainties begin to emerge about the tectonic framework within which quantitative forecasting can be made. Part of this methodology extension has been to adopt expert elicitation techniques to capture differing expert views as a means of addressing such uncertainties. This paper briefly outlines progress in this development work to date. (authors)

An approach to improve Romanian geological repository planning

International Nuclear Information System (INIS)

Andrei, Veronica; Prisecaru, Ilie

2016-01-01

International standards recommend typical phases to be included within any national program for the development of a geological repository dedicated to disposal of the high level radioactive wastes generated in countries using nuclear power. However, these are not universally applicable and the content of each of these phases may need to be adapted for each national situation and regulatory and institutional framework. Several national geological repository programs have faced failures in schedules and have revised their programs to consider an adapted phased management approach. The authors have observed that in the case of those countries in the early phases of a geological repository program where boundary conditions have not been fully defined, international recommendations for handling delays/failures in the national program might not immediately help. This paper considers a case study of the influences of the national context risks on the current planning schedule of the Romanian national geological repository. It proposes an optimum solution for an integrated response to any significant adverse impact arising from these risks, enabling sustainable program planning

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 2. Commercial waste forms, packaging and projections for preconceptual repository design studies

Energy Technology Data Exchange (ETDEWEB)

1978-04-01

This volume, Y/OWI/TM-36/2, ''Commercial Waste Forms, Packaging and Projections for Preconceptual Repository Design Studies,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This volume contains the data base for waste forms, packages, and projections from the commercial waste defined by the Office of Waste Isolation in ''Nuclear Waste Projections and Source Term Data for FY 1977,'' Y/OWI/TM-34. Also, as an alternative data base for repository design and analysis, waste forms, packages, and projections for commercial waste defined by Battelle Pacific Northwest Laboratory (BPNL) have been included. This data base consists of a reference case for use in the alternative design study and a definition of combustible wastes for use in mine fire and hydrogen generation analyses.

Scientific basis for a safety case of deep geological repositories

Energy Technology Data Exchange (ETDEWEB)

Noseck, Ulrich; Becker, Dirk-Alexander; Brasser, Thomas [and others

2012-11-15

Within this project strategies and methods to build a safety case for deep geological repositories are further developed. This includes also the scientific fundamentals as a basis of the safety case. In the international framework the methodology of the Safety Case is frequently applied and continuously improved. According to definitions from IAEA and NEA the Safety Case is a compilation of arguments and facts, which describe, quantify and support the safety and the degree of confidence in the safety of the geological repository. The safety of the geological repository should be demonstrated by the safety case. The safety case is the basis for essential decisions during a repository programme. It comprises the results of safety assessments in combination with additional information like multiple lines of evidence and a discussion of robustness and quality of the repository, its design and the quality of all safety assessments including the basic assumptions. A crucial element of the Safety Case is the long-term safety analysis, i.e. the systematic analysis of the hazards connected with the facility and the capability of site and repository design to ensure the required safety functions and to fulfill the technical claims. Long-term safety analysis requires a powerful and qualified programme package, which contains appropriate hardware and software as well as well trained and experienced modellers performing the model calculations. The calculation tools used within safety cases need to be checked and verified and continuously adapted to the state-of-the-art science and technology. Especially it needs to be applicable to a real repository system. For the assessment of safety a deep process understanding is necessary. The R and D work performed within this project will contribute to the improvement of process and system understanding as well as to the further development of methods and strategies applied in the safety case. Emphasis was put on the following aspects

Scientific basis for a safety case of deep geological repositories

International Nuclear Information System (INIS)

Noseck, Ulrich; Becker, Dirk-Alexander; Brasser, Thomas

2012-11-01

Within this project strategies and methods to build a safety case for deep geological repositories are further developed. This includes also the scientific fundamentals as a basis of the safety case. In the international framework the methodology of the Safety Case is frequently applied and continuously improved. According to definitions from IAEA and NEA the Safety Case is a compilation of arguments and facts, which describe, quantify and support the safety and the degree of confidence in the safety of the geological repository. The safety of the geological repository should be demonstrated by the safety case. The safety case is the basis for essential decisions during a repository programme. It comprises the results of safety assessments in combination with additional information like multiple lines of evidence and a discussion of robustness and quality of the repository, its design and the quality of all safety assessments including the basic assumptions. A crucial element of the Safety Case is the long-term safety analysis, i.e. the systematic analysis of the hazards connected with the facility and the capability of site and repository design to ensure the required safety functions and to fulfill the technical claims. Long-term safety analysis requires a powerful and qualified programme package, which contains appropriate hardware and software as well as well trained and experienced modellers performing the model calculations. The calculation tools used within safety cases need to be checked and verified and continuously adapted to the state-of-the-art science and technology. Especially it needs to be applicable to a real repository system. For the assessment of safety a deep process understanding is necessary. The R and D work performed within this project will contribute to the improvement of process and system understanding as well as to the further development of methods and strategies applied in the safety case. Emphasis was put on the following aspects

Long-term environmental impacts of geologic repositories

International Nuclear Information System (INIS)

Pigford, T.H.

1983-05-01

This paper summarizes a study of the long-term environmental impacts of geologic repositories for radioactive wastes. Conceptual repositories in basalt, granite, salt, and tuff were considered. Site-specific hydrological and geochemical parameters were used wherever possible, supplemented with generic parameters when necessary. Radiation doses to future maximally exposed individuals who use the contaminated groundwater and surface water were calculated and compared with a performance criterion of 10 -4 Sv/yr for radiation exposures from probable events. The major contributors to geologic isolation are the absence of groundwater if the repository is in natural salt, the slow dissolution of key radioelements as limited by solubility and by diffusion and convection in groundwater, long water travel times from the waste to the environment, and sorption retardation in the media surrounding the repository. In addition, dilution by surface water can considerably reduce the radiation exposures that result from the small fraction of the waste radioactivity that may ultimately reach the environment. Estimates of environmental impacts are made both for unreprocessed spent fuel and for reprocessing wastes. Accelerated dissolution of waste exposed to groundwater during the period of repository heating is also considered. This study of environmental impacts is a portion of a more comprehensive study of geologic waste disposal carried out by the Waste Isolation System Panel of the US National Research Council

Office of Geologic Repositories program baseline procedures notebook (OGR/B-1)

International Nuclear Information System (INIS)

1986-06-01

Baseline management is typically applied to aid in the internal control of a program by providing consistent programmatic direction, control, and surveillance to an evolving system development. This fundamental concept of internal program control involves the establishment of a baseline to serve as a point of departure for consistent technical program coordination and to control subsequent changes from that baseline. The existence of a program-authorized baseline ensures that all participants are working to the same ground rules. Baseline management also ensures that, once the baseline is defined, changes are assessed and approved by a process which ensures adequate consideration of overall program impact. Baseline management also includes the consideration of examptions from the baseline. The process of baseline management continues through all the phases of an evolving system development program. As the Program proceeds, there will be a progressive increase in the data contained in the baseline documentation. Baseline management has been selected as a management technique to aid in the internal control of the Office of Geologic Repositories (OGR) program. Specifically, an OGR Program Baseline, including technical and programmatic requirements, is used for program control of the four Mined Geologic Disposal System field projects, i.e., Basalt Waste Isolation Project, Nevada Nuclear Waste Storage Investigation, Salt Repository Project and Crystalline Repository Project. This OGR Program Baseline Procedures Notebook provides a description of the baseline mwanagement concept, establishes the OGR Program baseline itself, and provides procedures to be followed for controlling changes to that baseline. The notebook has a controlled distribution and will be updated as required

Geologic environments for nuclear waste repositories

Directory of Open Access Journals (Sweden)

Paleologos Evan K.

2017-01-01

Full Text Available High-level radioactive waste (HLW results from spent reactor fuel and reprocessed nuclear material. Since 1957 the scientific consensus is that deep geologic disposal constitutes the safest means for isolating HLW for long timescales. Nuclear power is becoming significant for the Arab Gulf countries as a way to diversify energy sources and drive economic developments. Hence, it is of interest to the UAE to examine the geologic environments currently considered internationally to guide site selection. Sweden and Finland are proceeding with deep underground repositories mined in bedrock at depths of 500m, and 400m, respectively. Equally, Canada’s proposals are deep burial in the plutonic rock masses of the Canadian Shield. Denmark and Switzerland are considering disposal of their relative small quantities of HLW into crystalline basement rocks through boreholes at depths of 5,000m. In USA, the potential repository at Yucca Mountain, Nevada lies at a depth of 300m in unsaturated layers of welded volcanic tuffs. Disposal of low and intermediate-level radioactive wastes, as well as the German HLW repository favour structurally-sound layered salt stata and domes. Our article provides a comprehensive review of the current concepts regarding HLW disposal together with some preliminary analysis of potentially appropriate geologic environments in the UAE.

Industrial complementarities between interim storage and reversible geological repository - 59237

International Nuclear Information System (INIS)

Hoorelbeke, Jean-Michel

2012-01-01

The French Act voted in 2006 made the choice of deep geological disposal as the reference option for the long term management of high level (HLW) and intermediate level long-lived waste. The CIGEO repository project aims at avoiding or limiting burden to future generations, which could not be achieved by the extension in time of interim storage. The reversibility as provided by the Act will maintain a liberty of choice for waste management on a duration which is comparable to new storage facility. Interim storage is required to accommodate waste as long as the repository is not available. The commissioning of the repository in 2025 will not suppress needs for interim storage. The paper describes the complementarities between existing and future interim storage facilities and the repository project: repository operational issues and planning, HLW thermal decay, support for the reversibility, etc. It shows opportunities to prepare a global optimization of waste management including the utilization at best of storage capacities and the planning of waste emplacement in the repository in such a way to facilitate operational conditions and to limit cost. Preliminary simulations of storage-disposal scenarios are presented. Thanks to an optimal use of the waste management system, provision can be made for a progressive increase of waste emplacement flow during the first operation phase of the repository. It is then possible to stabilize the industrial activity level of the repository site. An optimal utilization of interim storage can also limit the diversity of waste packages emplaced simultaneously, which facilitates the operation of the repository. 60 years minimum interim storage duration is generally required with respect to HLW thermal output. Extending this interim storage period may reduce the underground footprint of the repository. Regarding reversibility, the capability to manage waste packages potentially retrieved from the repository should be analyzed. The

OPG's deep geologic repository for low and intermediate level waste - recent progress

International Nuclear Information System (INIS)

King, F.K.

2006-01-01

This paper provides a status report on Canada's first project to build a permanent repository for the long-term management of radioactive waste. Ontario Power Generation has initiated a project to construct a deep geologic repository for low- and intermediate-level waste at the Bruce Nuclear Site, at a depth in the range of 600 to 800 m in an Ordovician-age argillaceous limestone formation. The project is currently undergoing an Environmental Assessment and consulting companies in the areas of environmental assessment, geoscientific site characterization, engineering and safety assessment have been hired and technical studies are underway. Seismic surveys and borehole drilling will be initiated in the fall of 2006. The next major milestone for the project is the submission of the Environmental Assessment report, currently scheduled for December 2008. (author)

Technical expertise on the safety of the proposed geological repository sites. Planning for geological deep repositories, step 1; Sicherheitstechnisches Gutachten zum Vorschlag geologischer Standortgebiete. Sachplan geologische Tiefenlager, Etappe 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-01-15

On October 17, 2010, on request of those Swiss government institutions responsible for the disposal of radioactive wastes, the National Co-operative for the Disposal of Radioactive Waste (NAGRA) presented its project concerning geological sites for the foreseen disposal of radioactive wastes to the Federal Authorities. According to the present disposal concept, two types of repository are foreseen: one for highly radioactive wastes (HAA) and the other for low radioactive and intermediate-level radioactive wastes (SMA). If a site fulfils the necessary conditions for both HAA as well as for SMA, a combined site for both types of waste may be chosen. As a qualified control authority in Switzerland, the Federal Nuclear Safety Inspectorate (ENSI) has to examine the quality of the NAGRA proposals from the point of view of the nuclear safety of the sites. The project for deep underground waste disposal first defines the process and the criteria according to which sites for the geological storage of all types of radioactive wastes in Switzerland have to be chosen. The choice is based on the actual knowledge of Swiss geology. After dividing the wastes into SMA and HAA, some large-scale areas are to be identified according to their suitability from the geological and tectonic points of view. NAGRA's division of waste into SMA and HAA is based on calculations of the long-term safety for a broad range of different rock types and geological situations and takes the different properties of all waste types into account. As a conclusion, a small portion of SMA has to be stored with {alpha}-toxic wastes in the HAA repository. The estimation of the total volume of wastes to be stored is based on 60 years of operation of the actual nuclear power plants, augmented with the wastes from possible replacement plants with a total power of 5 GW{sub e} during a further 60 years. The safety concept of the repository is based on passive systems using technical and natural barriers. The

Safety analysis of the proposed Canadian geologic nuclear waste repository

International Nuclear Information System (INIS)

Prowse, D.R.

1977-01-01

The Canadian program for development and qualification of a geologic repository for emplacement of high-level and long-lived, alpha-emitting waste from irradiated nuclear fuel has been inititiated and is in its initial development stage. Fieldwork programs to locate candidate sites with suitable geological characteristics have begun. Laboratory studies and development of models for use in safety analysis of the emplaced nuclear waste have been initiated. The immediate objective is to complete a simplified safety analysis of a model geologic repository by mid-1978. This analysis will be progressively updated and will form part of an environmental Assessment Report of a Model Fuel Center which will be issued in mid-1979. The long-term objectives are to develop advanced safety assessment models of a geologic repository which will be available by 1980

Monitoring of geological repositories for high level radioactive waste

International Nuclear Information System (INIS)

2001-04-01

Geological repositories for disposal of high level radioactive waste are designed to provide isolation of the waste from human environment for many thousands of years. This report discusses the possible purposes for monitoring geological repositories at the different stages of a repository programme, the use that may be made of the information obtained and the techniques that might be applied. This report focuses on the different objectives that monitoring might have at various stages of a programme, from the initiation of work on a candidate site, to the period after repository closure. Each objective may require somewhat different types of information, or may use the same information in different ways. Having evaluated monitoring requirements, the report concludes with a brief evaluation of available monitoring techniques

Diversion path analysis for the Swedish geological repository

International Nuclear Information System (INIS)

Fritzell, Anni; Meer, Klaas Van Der

2008-02-01

The Swedish strategy to handle the spent fuel from the nuclear power plants is direct disposal in a geological repository. The safeguards regime covering all nuclear material in the state will be expanded to cover the new repository, which will require a novel safeguards approach due mainly to the inaccessibility of the fuel after disposal. The safeguards approach must be able to provide a high level of assurance that the fuel in the repository not diverted, but must also be resource efficient. An attractive approach with regards to use of resources is to monitor only the access points to the repository, i.e. the openings. The implementation of such an approach can only be allowed if it is shown to be sufficiently secure. With the purpose of determining the applicability of this 'black box' approach, a diversion path analysis for the Swedish geological repository has been carried out. The result from the analysis shows that all credible diversion paths could be covered by the black-box safeguards approach provided that the identified boundary conditions can be met

Diversion path analysis for the Swedish geological repository

Energy Technology Data Exchange (ETDEWEB)

Fritzell, Anni (Dept. of Physics and Astronomy, Uppsala Univ., Uppsala (Sweden)); Meer, Klaas Van Der (Belgian Nuclear Research Center SCK.CEN (BG))

2008-02-15

The Swedish strategy to handle the spent fuel from the nuclear power plants is direct disposal in a geological repository. The safeguards regime covering all nuclear material in the state will be expanded to cover the new repository, which will require a novel safeguards approach due mainly to the inaccessibility of the fuel after disposal. The safeguards approach must be able to provide a high level of assurance that the fuel in the repository not diverted, but must also be resource efficient. An attractive approach with regards to use of resources is to monitor only the access points to the repository, i.e. the openings. The implementation of such an approach can only be allowed if it is shown to be sufficiently secure. With the purpose of determining the applicability of this 'black box' approach, a diversion path analysis for the Swedish geological repository has been carried out. The result from the analysis shows that all credible diversion paths could be covered by the black-box safeguards approach provided that the identified boundary conditions can be met

Siting regions for deep geological repositories. Why just here?

International Nuclear Information System (INIS)

Rieser, A.

2009-09-01

This report helps to the popularization of the Nagra works accomplished for the management and disposal of the radioactive wastes in Switzerland. The programme for management and disposal of the radioactive wastes are extensively determined by regulations. Protection of mankind and environment is the primary objective. The basic storage process is considered as having been solved. The question addressed in the report is where the facility has to be built; the site selection procedure includes five steps: 1) according to their type the wastes have to be allocated to two different repositories: for low- and intermediate-level wastes (L/ILW), and for high-level and alpha-toxic wastes (HLW); 2) the safety concept for both repositories and the requirements on the geology have to be determined; 3) large suitable geological-tectonic zones must be found where repositories could be built; 4) in these geological zones a suitable host rock has to be identified; 5) the most important spatial geological conditions of the host rock (minimum depth with respect to surface erosion, maximum depth in terms of engineering requirements, lateral extent) have to be identified. Based on these criteria, three suitable siting regions for a HLW repository were found in the North of Switzerland. The preferred host rock is Opalinus clay because of its very low permeability; it is therefore an excellent barrier against nuclide transport. In the three proposed siting regions, Opalinus clay is present in sufficient volumes at a suitable depth. For a L/ILW repository six different possible siting regions were identified, five in Northern Switzerland and one in Central Switzerland. In the three siting regions found for a possible HLW repository, it would also be possible to built a combined repository for both HLW and L/ILW wastes

Current Status of Deep Geological Repository Development

International Nuclear Information System (INIS)

Budnitz, R J

2005-01-01

This talk provided an overview of the current status of deep-geological-repository development worldwide. Its principal observation is that a broad consensus exists internationally that deep-geological disposal is the only long-term solution for disposition of highly radioactive nuclear waste. Also, it is now clear that the institutional and political aspects are as important as the technical aspects in achieving overall progress. Different nations have taken different approaches to overall management of their highly radioactive wastes. Some have begun active programs to develop a deep repository for permanent disposal: the most active such programs are in the United States, Sweden, and Finland. Other countries (including France and Russia) are still deciding on whether to proceed quickly to develop such a repository, while still others (including the UK, China, Japan) have affirmatively decided to delay repository development for a long time, typically for a generation of two. In recent years, a major conclusion has been reached around the world that there is very high confidence that deep repositories can be built, operated, and closed safely and can meet whatever safety requirements are imposed by the regulatory agencies. This confidence, which has emerged in the last few years, is based on extensive work around the world in understanding how repositories behave, including both the engineering aspects and the natural-setting aspects, and how they interact together. The construction of repositories is now understood to be technically feasible, and no major barriers have been identified that would stand in the way of a successful project. Another major conclusion around the world is that the overall cost of a deep repository is not as high as some had predicted or feared. While the actual cost will not be known in detail until the costs are incurred, the general consensus is that the total life-cycle cost will not exceed a few percent of the value of the

Complex geologic characterization of the repository environment

Energy Technology Data Exchange (ETDEWEB)

Harper, T R [British Petroleum Research Center, Sunberry, England; Szymanski, J S

1982-01-01

The present basis for characterizing geological environments is identified in this paper, and the additional requirements imposed by the need to isolate high-level waste safely are discussed. Solutions to these additional requirements are proposed. The time scale of concern and the apparent complexity of the required multidisciplinary approach are identified. It is proposed that an increased use of the geologic record, together with a recognition that all geologic processes operate within an interdependent system, be a key feature in geologic characterization of deep repositories.

Redox processes in the safety case of deep geological repositories of radioactive wastes. Contribution of the European RECOSY Collaborative Project

International Nuclear Information System (INIS)

Duro, L.; Bruno, J.; Grivé, M.; Montoya, V.; Kienzler, B.; Altmaier, M.; Buckau, G.

2014-01-01

Highlights: • The RECOSY project produced results relevant for the Safety Case of nuclear disposal. • We classify the safety related features where RECOSY has contributed. • Redox processes effect the retention of radionuclides in all repository subsystems. - Abstract: Redox processes influence key geochemical characteristics controlling radionuclide behaviour in the near and far field of a nuclear waste repository. A sound understanding of redox related processes is therefore of high importance for developing a Safety Case, the collection of scientific, technical, administrative and managerial arguments and evidence in support of the safety of a disposal facility. This manuscript presents the contribution of the specific research on redox processes achieved within the EURATOM Collaborative Project RECOSY (REdox phenomena COntrolling SYstems) to the Safety Case of nuclear waste disposal facilities. Main objectives of RECOSY were related to the improved understanding of redox phenomena controlling the long-term release or retention of radionuclides in nuclear waste disposal and providing tools to apply the results to Performance Assessment and the Safety Case. The research developed during the project covered aspects of the near-field and the far-field aspects of the repository, including studies relevant for the rock formations considered in Europe as suitable for hosting an underground repository for radioactive wastes. It is the intention of this paper to highlight in which way the results obtained from RECOSY can feed the scientific process understanding needed for the stepwise development of the Safety Case associated with deep geological disposal of radioactive wastes

Natural analogues: studies of geological processes relevant to radioactive waste disposal in deep geological repositories

Energy Technology Data Exchange (ETDEWEB)

Russel, A.W. [Bedrock Geosciences, Auenstein (Switzerland); Reijonen, H.M. [Saanio and Rickkola Oy, Helsinki (Finland); McKinley, I.G. [MCM Consulting, Baden-Daettwil (Switzerland)

2015-06-15

The geological disposal of radioactive wastes is generally accepted to be the most practicable approach to handling the waste inventory built up from over 70 years accumulation of power production, research-medical-industrial and military wastes. Here, a brief overview of the approach to geological disposal is presented along with some information on repository design and the assessment of repository post-closure safety. One of the significant challenges for repository safety assessment is how to extrapolate the likely long-term (i.e. ten thousand to a million years) behaviour of the repository from the necessarily short term data from analytical laboratories and underground rock laboratories currently available. One approach, common to all fields of the geosciences, but also in such diverse fields as philosophy, biology, linguistics, law, etc., is to utilise the analogue argumentation methodology. For the specific case of radioactive waste management, the term 'natural analogue' has taken on a particular meaning associated with providing supporting arguments for a repository safety assessment. This approach is discussed here with a brief overview of how the study of natural (and, in particular, geological) systems can provide supporting information on the likely long-term evolution of a deep geological waste repository. The overall approach is discussed and some relevant examples are presented, including the use of uranium ore bodies to assess waste form stability, the investigation of native metals to define the longevity of waste containers and how natural clays can provide information on the stability of waste tunnel backfill material. (authors)

Natural analogues: studies of geological processes relevant to radioactive waste disposal in deep geological repositories

International Nuclear Information System (INIS)

Russel, A.W.; Reijonen, H.M.; McKinley, I.G.

2015-01-01

The geological disposal of radioactive wastes is generally accepted to be the most practicable approach to handling the waste inventory built up from over 70 years accumulation of power production, research-medical-industrial and military wastes. Here, a brief overview of the approach to geological disposal is presented along with some information on repository design and the assessment of repository post-closure safety. One of the significant challenges for repository safety assessment is how to extrapolate the likely long-term (i.e. ten thousand to a million years) behaviour of the repository from the necessarily short term data from analytical laboratories and underground rock laboratories currently available. One approach, common to all fields of the geosciences, but also in such diverse fields as philosophy, biology, linguistics, law, etc., is to utilise the analogue argumentation methodology. For the specific case of radioactive waste management, the term 'natural analogue' has taken on a particular meaning associated with providing supporting arguments for a repository safety assessment. This approach is discussed here with a brief overview of how the study of natural (and, in particular, geological) systems can provide supporting information on the likely long-term evolution of a deep geological waste repository. The overall approach is discussed and some relevant examples are presented, including the use of uranium ore bodies to assess waste form stability, the investigation of native metals to define the longevity of waste containers and how natural clays can provide information on the stability of waste tunnel backfill material. (authors)

Optimized application of systems engineering to nuclear waste repository projects

International Nuclear Information System (INIS)

Miskimin, P.A.; Shepard, M.

1986-01-01

The purpose of this presentation is to describe a fully optimized application of systems engineering methods and philosophy to the management of a large nuclear waste repository project. Knowledge gained from actual experience with the use of the systems approach on two repository projects is incorporated in the material presented. The projects are currently evaluating the isolation performance of different geologic settings and are in different phases of maturity. Systems engineering methods were applied by the principal author at the Waste Isolation Pilot Plant (WIPP) in the form of a functional analysis. At the Basalt Waste Isolation Project (BWIP), the authors assisted the intergrating contractor with the development and application of systems engineering methods. Based on this experience and that acquired from other waste management projects, an optimized plan for applying systems engineering techniques was developed. The plan encompasses the following aspects: project organization, developing and defining requirements, assigning work responsibilities, evaluating system performance, quality assurance, controlling changes, enhancing licensability, optimizing project performance, and addressing regulatory issues. This information is presented in the form of a roadmap for the practical application of system engineering principles to a nuclear waste repository project

Geological status of NWTS repository siting activities in the paradox basin

International Nuclear Information System (INIS)

Frazier, N.A.; Conwell, F.R.

1981-01-01

Emplacement of waste packages in mined geological repositories is one method being evaluated for isolating high-level nuclear wastes. Granite, dome salt, tuff, basalt and bedded salt are among the rock types being investigated. Described in this paper is the status of geological activities in the Paradox Basin of Utah and Colorado, one region being explored as a part of the National Waste Terminal Storage (NWTS) program to site a geological repository in bedded salt

Crystalline Repository Project. Technical progress report, October 1982-March 1983

International Nuclear Information System (INIS)

1985-01-01

This document reports the progress being made periodically on the development of a geologic repository in crystalline rock for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Crystalline Respository Development (OCRD), a prime contractor of the US Department of Energy Repository Project Office. The studies include work by other prime contractors and by subcontractors to OCRD

Performance Assessment Strategy Plan for the Geologic Repository Program

International Nuclear Information System (INIS)

1990-01-01

Performance assessment is a major constituent of the program being conducted by the US Department of Energy (DOE) to develop a geologic repository. Performance assessment is the set of activities needed for quantitative evaluations to assess compliance with the performance requirements in the regulations for a geologic repository and to support the development of the repository. The strategy for these evaluations has been documented in the Performance Assessment Strategy Plan (DOE, 1989). The implementation of the performance assessment strategy is defined in this document. This paper discusses the scope and objectives of the implementation plan, the relationship of the plan to other program plans, summarizes the performance assessment areas and the integrated strategy of the performance assessment program. 1 fig., 3 tabs

Relationship of engineering geology to conceptual repository design in the Gibson Dome area, Utah

International Nuclear Information System (INIS)

Helgerson, R.; Henderson, N.

1984-01-01

The Paradox Basin in Southeastern Utah is being investigated as a potential site for development of a high-level nuclear waste repository. Geologic considerations are key areas of concern and influence repository design from a number of aspects: depth to the host rock, thickness of the host rock, and hydrologic conditions surrounding the proposed repository are of primary concern. Surface and subsurface investigations have provided data on these key geologic factors for input to the repository design. A repository design concept, based on the surface and subsurface geologic investigations conducted at Gibson Dome, was synthesized to provide needed information on technical feasibility and cost for repository siting decision purposes. Significant features of the surface and subsurface repository facilities are presented. 5 references, 4 figures

Planning and Design Considerations for Geological Repository Programmes of Radioactive Waste

International Nuclear Information System (INIS)

2014-11-01

Disposal in a geological repository is the generally accepted solution for the long term management of high level and/or long lived radioactive wastes, in line with the general principles defined in the IAEA Safety Fundamentals. This publication presents practical information on the way a geological repository programme for radioactive waste could be defined and planned, with special attention to all aspects having an impact on the timing. Country specific examples for repository development phases are provided, based on actual experiences from Member States

Geological repositories: The last nuclear frontier. International Conference on Geological Repositories: Political and Technical Progress, 8-10 December 2003, Stockholm, Sweden

International Nuclear Information System (INIS)

ElBaradei, M.

2003-01-01

Few issues play so central a role in the public acceptance of nuclear technologies as the management and disposal of spent fuel and radioactive waste. In the current climate, geological repositories have come to be viewed not as one option among many for completing the nuclear fuel cycle, but as the only sustainable solution achievable in the near term. But despite a longstanding agreement among experts that geological disposal can be safe, technologically feasible and environmentally sound, a large part of the general public remains skeptical. This statement deals with the challenges that IAEA is facing to build public confidence related to spent fuel repositories

10 CFR 63.161 - Emergency plan for the geologic repository operations area through permanent closure.

Science.gov (United States)

2010-01-01

... Planning Criteria § 63.161 Emergency plan for the geologic repository operations area through permanent... 10 Energy 2 2010-01-01 2010-01-01 false Emergency plan for the geologic repository operations area... may occur at the geologic repository operations area, at any time before permanent closure and...

Geological criteria for site selection of an LILW radioactive waste repository in the Philippines

International Nuclear Information System (INIS)

Aurelio, Mario; Taguibao, Kristine Joy; Vargas, Edmundo; Palattao, Maria Visitacion; Reyes, Rolando; Nohay, Carl; Singayan, Alfonso

2013-01-01

In the selection of sites for disposal facilities involving low- and intermediate-level radioactive waste (LILW), International Atomic Energy Agency (IAEA) recommendations require that 'the region in which the site is located shall be such that significant tectonic and surface processes are not expected to occur with an intensity that would compromise the required isolation capability of the repository'. Evaluating the appropriateness of a site therefore requires a deep understanding of the geological and tectonic setting of the area. The Philippines sits in a tectonically active region frequented by earthquakes and volcanic activity. Its highly variable morphology coupled with its location along the typhoon corridor in the west Pacific region subjects the country to surface processes often manifested in the form of landslides. The Philippine LILW near surface repository project site is located on the north eastern sector of the Island of Luzon in northern Philippines. This island is surrounded by active subduction trenches; to the east by the East Luzon Trough and to the west by the Manila Trench. The island is also traversed by several branches of the Philippine Fault System. The Philippine LILW repository project is located more than 100 km away from any of these major active fault systems. In the near field, the project site is located less than 10 km from a minor fault (Dummon River Fault) and more than 40 km away from a volcanic edifice (Mt. Caguas). This paper presents an analysis of the potential hazards that these active tectonic features may pose to the project site. The assessment of such geologic hazards is imperative in the characterization of the site and a crucial input in the design and safety assessment of the repository. (authors)

Geological criteria for site selection of an LILW radioactive waste repository in the Philippines

Energy Technology Data Exchange (ETDEWEB)

Aurelio, Mario; Taguibao, Kristine Joy [National Institute of Geological Sciences, University of the Philippines, Quezon City (Philippines); Vargas, Edmundo; Palattao, Maria Visitacion; Reyes, Rolando; Nohay, Carl; Singayan, Alfonso [Philippine Nuclear Research Institute, Department of Science and Technology, Quezon City (Philippines)

2013-07-01

In the selection of sites for disposal facilities involving low- and intermediate-level radioactive waste (LILW), International Atomic Energy Agency (IAEA) recommendations require that 'the region in which the site is located shall be such that significant tectonic and surface processes are not expected to occur with an intensity that would compromise the required isolation capability of the repository'. Evaluating the appropriateness of a site therefore requires a deep understanding of the geological and tectonic setting of the area. The Philippines sits in a tectonically active region frequented by earthquakes and volcanic activity. Its highly variable morphology coupled with its location along the typhoon corridor in the west Pacific region subjects the country to surface processes often manifested in the form of landslides. The Philippine LILW near surface repository project site is located on the north eastern sector of the Island of Luzon in northern Philippines. This island is surrounded by active subduction trenches; to the east by the East Luzon Trough and to the west by the Manila Trench. The island is also traversed by several branches of the Philippine Fault System. The Philippine LILW repository project is located more than 100 km away from any of these major active fault systems. In the near field, the project site is located less than 10 km from a minor fault (Dummon River Fault) and more than 40 km away from a volcanic edifice (Mt. Caguas). This paper presents an analysis of the potential hazards that these active tectonic features may pose to the project site. The assessment of such geologic hazards is imperative in the characterization of the site and a crucial input in the design and safety assessment of the repository. (authors)

Crystalline Repository Project: Technical progress report for the period October 1, 1982--May 28, 1986

International Nuclear Information System (INIS)

1988-11-01

This document reports the progress made on the development of a second geologic repository in crystalline rocks during the duration of the Crystalline Repository Project from its inception in October 1982 to its termination in May 1986. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Waste Technology Development (OWTD), successor to the Office of Crystalline Repository Development. OWTD is a prime contractor of the US Department of Energy (DOE) Repository Technology Program Office, itself the successor to the Crystalline Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Crystalline Repository Development. 151 refs

IAEA perspectives on geological repositories. Address at the international conference on geological repositories, Denver, 1 November 1999

International Nuclear Information System (INIS)

ElBaradei, M.

1999-01-01

In his address at the International Conference on Geological Repositories (Denver, 1 November 1999), the Director General of the IAEA gave a general presentation of the problem of disposal of high-level radioactive waste, and described the current situation in the countries using nuclear energy including present and future Agency's activities

The Ec prototype repository project: implications of assessments for refining repository design

International Nuclear Information System (INIS)

Svemar, C.

2004-01-01

The most important issue in the evaluation of the repository performance is the long term safety of the repository. Analyses for this issue focuses on the 'steady state' conditions which start at the time when the repository has been saturated and the groundwater table returned to its normal level. The bentonite buffer around the canisters is saturated and homogeneous, and the canister is located exactly in the centre of the buffer. The backfill in the tunnel has been saturated as well and fills the earlier open spaces in the tunnel completely. The task of the activities taking places prior to the start of the 'steady state' conditions, like excavation, deposition, backfilling and sealing, with due consideration to the processes a consequences they may cause in the long run, is to provide for these 'ideal' conditions, as close as possible. While studying these activities in detail it has become obvious that development of methods and techniques needs to be carefully addressed before the decision is made on how to apply them in the repository. One general finding is that the situation in engineering of details is not that much different from the situation in geological characterisation of a site in detail; one more detail of engineering and the consequences it brings often complicates the situation rather than supports the solution prioritized so far. Many of the practical issues have been studied in the Prototype Repository project in the AEspoe Hard Rock Laboratory (Pusch et al., 2000). The Prototype Repository consists of two sections with four respectively two deposition holes with bentonite buffer and canister, the latter holding electrical heaters. The sections are separated by a concrete plug, and the whole test is to be separated from the rest of the laboratory by an outer plug. The project has two objectives: 1. To demonstrate the integrated function of tile deep repository components under realistic conditions and to compare results with models and

Monitored Geologic Repository Concept of Operations

International Nuclear Information System (INIS)

Curry, P.M.

1999-01-01

This updated document provides the top level guidance for development of the individual systems for the MGR which will be further developed in the System Description Documents. This document will serve as guidance for the development of functional interface and operational requirements. However, the data and engineering values presented in Monitored Geologic Repository Concept of Operations are provided as estimates or summaries of the current design. The original analyses or supporting documents must be utilized if the data or engineering values are used for design inputs. The concepts presented will be utilized as inputs for the development of operational concepts for the individual systems. It is recognized that the references listed may contain existing data or data which are to be verified. However, the data and engineering values presented will not impact the concepts presented in this technical document. As such, the data and engineering values are not being tracked as To Be Verified data. This revision was created to incorporate changes resulting from Enhanced Design Alternative II and Revision 3, DCN 01, of the Monitored Geologic Repository Requirements (YMP 1999)

The deep geologic repository technology programme: toward a geoscience basis for understanding repository safety

International Nuclear Information System (INIS)

Jensen, M.R.

2007-01-01

Within the Deep Geologic Repository Technology Programme (DGRTP) several Geoscience activities are focused on advancing the understanding of groundwater flow system evolution and geochemical stability in a Canadian Shield setting as affected by long-term climate change. A key aspect is developing confidence in predictions of groundwater flow patterns and residence times as they relate to the safety of a deep geologic repository for used nuclear fuel waste. This is being achieved through a coordinated multi-disciplinary approach intent on: i) demonstrating coincidence between independent geo-scientific data; ii) improving the traceability of geo-scientific data and its interpretation within a conceptual descriptive model(s); iii) improving upon methods to assess and demonstrate robustness in flow domain prediction(s) given inherent flow domain uncertainties (i.e. spatial chemical/physical property distributions, boundary conditions) in time and space; and iv) improving awareness amongst geo-scientists as to the utility of various geo-scientific data in supporting a safety case for a deep geologic repository. This multi-disciplinary DGRTP approach is yielding an improved understanding of groundwater flow system evolution and stability in Canadian Shield settings that is further contributing to the geo-scientific basis for understanding and communicating aspects of DGR safety. (author)

Compliance demonstration: What can be reasonably expected from safety assessment for geological repositories?

International Nuclear Information System (INIS)

Zuidema, P.; Smith, P.; Sumerling, T.

1999-01-01

When licensing a nuclear facility, it is important to demonstrate that it will comply with regulatory limits (e.g. individual dose limits) and also show that sufficient attention has been paid to optimisation of facility design and operation, such that any associated radiological impacts will be as low as reasonably achievable (ALARA). In general, in demonstrating compliance, experience can be drawn from the performance of existing and similar facilities, and monitoring plans can be specified that will confirm that actual radiological discharges during operations are within authorised limits for the facility. This is also true in respect of the operational period of a geological repository. For the post-closure phase of a repository, however, it is also necessary to show that possible releases will remain acceptably low even at long times in the future when, it is assumed, control of the facility has lapsed and there is no method of either monitoring releases or taking remedial action in the case of unexpected events or releases. In addition, within each country, a deep geological repository will be a first-of-a-kind development so that compliance arguments can be expected to be rigorously tested without any assistance from the precedent of licensing of similar facilities nationally. This puts heavy, and quite unusual, burdens on the long-term safety assessment for a geological repository to develop a case that is sufficiently strong to demonstrate compliance. This paper focuses on the problem of demonstrating compliance with long-term safety requirements for a geological repository, and explores: the overall aims and special difficulties of demonstrating compliance for a geological repository; the role of safety assessment in demonstrating compliance; the scope for optimisation of a geological repository and importance of robustness and lessons learnt from the application of safety assessment. In addition, some issues requiring further discussion and clarification

Three-dimensional Geological and Geo-mechanical Modelling of Repositories for Nuclear Waste Disposal in Deep Geological Structures

International Nuclear Information System (INIS)

Fahland, Sandra; Hofmann, Michael; Bornemann, Otto; Heusermann, Stefan

2008-01-01

To prove the suitability and safety of underground structures for the disposal of radioactive waste extensive geo-scientific research and development has been carried out by BGR over the last decades. Basic steps of the safety analysis are the geological modelling of the entire structure including the host rock, the overburden and the repository geometry as well as the geo-mechanical modelling taking into account the 3-D modelling of the underground structure. The geological models are generated using the special-construction openGEO TM code to improve the visualisation an d interpretation of the geological data basis, e.g. borehole, mine, and geophysical data. For the geo-mechanical analysis the new JIFE finite-element code has been used to consider large 3-D structures with complex inelastic material behaviour. To establish the finite-element models needed for stability and integrity calculations, the geological models are simplified with respect to homogenous rock layers with uniform material behaviour. The modelling results are basic values for the evaluation of the stability of the repository mine and the long-term integrity of the geological barrier. As an example of application, the results of geological and geo-mechanical investigations of the Morsleben repository based on 3-D modelling are presented. (authors)

Safety- and performance indicators for a generic deep geological repository in clay

International Nuclear Information System (INIS)

Resele, G.; Niemeyer, M.; Wilhelm, St.; Heimer, St.; Mohlfeld, M.; Eilers, G.; Preuss, J.; Wollrath, J.

2010-01-01

Document available in extended abstract form only. As a first step of an impartial survey for an optimal site selection for a deep geological repository in Germany, potentially suitable regions shall be identified and localised according to their suitability. During the early phases of such a site selection procedure the information about the properties of the host rock and the geological situation at the potential sites is not very precise. As site investigation procedures are both expensive and time-consuming, it is essential to identify those properties of the geological barrier system that are most relevant for long-term safety. Furthermore, adequate indicators have to be chosen that allow a simple but efficient assessment of the suitability of the potential regions. Definition and application of 'exclusion criteria' based on single parameter values, e.g. the hydraulic conductivity of the host rock, is inadequate because the long-term safety depends on the interaction of many features and properties of the barrier system. In a research project, indicators have been developed which depend on the most relevant properties of the geological barriers and estimate the overall performance of a repository system. The application of these indicators on the barrier properties which have been found during the investigations of potential repository sites in clay located in Germany, Switzerland and France demonstrates how, for instance, an unfavourably high hydraulic permeability of the clay can be compensated by a large vertical extension of the clay layer and small hydraulic gradients. Other indicators evaluate the importance of hydraulic discontinuities and define the minimal requirements on technical barriers like seals and backfill of emplacement tunnels. When the information of the radionuclide inventory and the biosphere, especially the diluting aquifer is included, the indicators allow the estimation of the resulting dose which matches the result of a

Site selection of a deep repository of HLRW in relation to geological conditions of Slovak Republic

International Nuclear Information System (INIS)

Kovacik, M.; Kovacikova, M.; Madaras, J.; Vandlikova, M.

1996-01-01

All countries which use nuclear energy to generate electricity face the problem of high level radioactive waste (HLRW) and spent fuel. Until 1987, this problem was addressed in Czechoslovakia by transferring the material to the former USSR. After the political changes in Central and Eastern Europe in 1989 and the division of Czechoslovakia into two states in 1993, Slovakia independently faced the complex problem of creating its own deep repository. Although Slovakia has begun to solve the problem of HLRW and spent fuel only recently, it can take advantage of the theoretical and practical knowledge of other countries in this field. The geological aspects of the setting of the deep repository of HLRW have been studied within the project R epositories of radioactive and hazardous wastes in geological environment. The assessment of the Slovak Republic for creating a repository of HLRW was based on the application of internationally determined and applied criteria

Safeguards policy and strategies: An IAEA perspective for spent fuel in geological repositories

International Nuclear Information System (INIS)

Fattah, A.

2002-01-01

Safeguards for nuclear materials in geologic repositories have to be continued even after the repository has been backfilled and sealed. The nuclear materials disposed in a geologic repository may pose a higher and long-term proliferation risk because the inventory is many times the 'significant quantity' needed safeguards. The safeguards measures must be flexible enough to respond to the changing development of technology and changing need for current as well as future generations. Change in social, economic, environmental and other scenarios might demand recovery of nuclear and other materials from the repository sometime in the future. (author)

The influence of geological loading on the structural integrity of an underground nuclear waste repository

International Nuclear Information System (INIS)

Jakeman, N.

1985-08-01

Stresses are developed in underground nuclear waste repositories as a result of applied loads from geological movements caused by the encroachment of ice sheets or seismic activity for example. These stresses may induce fracturing of the waste matrix, repository vault and nearfield host geology. This fracturing will enhance the advective flow and allow more-rapid transfer of radionuclides from their encapsulation through the repository barriers and nearfield host rock. Geological loads may be applied either gradually as in crustal folding or encroachment of ice sheets, or rapidly as in the case of seismic movements. The analysis outlined in this report is conducted with a view to including the effects of geological loading in a probabilistic repository site assessment computer code such as SYVAC. (author)

Geological boundary conditions for a safety demonstration and verification concept for a HLW repository in claystone in Germany. AnSichT

Energy Technology Data Exchange (ETDEWEB)

Stark, Lena; Bebiolka, Anke; Gerardi, Johannes [Federal Institute for Geosciences and Natural Resources (BGR), Hannover (Germany). Dept. of Underground Space for Storage and Economic Use; and others

2015-07-01

Within the framework of the R and D project ''AnSichT'', DBE TECHNOLOGY, BGR and GRS are developing a method to demonstrate the safety of a HLW repository in claystone in Germany. The methodological approach basing on a holistic concept, links the legal and geologic boundary conditions, the disposal and closure concept, the demonstration of barrier integrity, and the long-term analysis of the repository evolution as well. The geologic boundary conditions are specified by the description of the geological situation and generic models, the selection of representative parameters and geoscientific long-term predictions. They form a fundament for the system analysis.

Deep geological isolation of nuclear waste: numerical modeling of repository scale hydrology

International Nuclear Information System (INIS)

Dettinger, M.D.

1980-04-01

The Scope of Work undertaken covers three main tasks, described as follows: (Task 1) CDM provided consulting services to the University on modeling aspects of the study having to do with transport processes involving the local groundwater system near the repository and the flow of fluids and vapors through the various porous media making up the repository system. (Task 2) CDM reviewed literature related to repository design, concentrating on effects of the repository geometry, location and other design factors on the flow of fluids within the repository boundaries, drainage from the repository structure, and the eventual transport of radionucldies away from the repository site. (Task 3) CDM, in a joint effort with LLL personnel, identified generic boundary and initial conditions, identified processes to be modeled, and recommended a modeling approach with suggestions for appropriate simplifications and approximations to the problem and identifiying important parameters necessary to model the processes. This report consists of two chapters and an appendix. The first chapter (Chapter III of the LLL report) presents a detailed description and discussion of the modeling approach developed in this project, its merits and weaknesses, and a brief review of the difficulties anticipated in implementing the approach. The second chapter (Chapter IV of the LLL report) presents a summary of a survey of researchers in the field of repository performance analysis and a discussion of that survey in light of the proposed modeling approach. The appendix is a review of the important physical processes involved in the potential hydrologic transport of radionuclides through, around and away from deep geologic nuclear waste repositories

Preliminary concepts: materials management in an internationally safeguarded nuclear-waste geologic repository

International Nuclear Information System (INIS)

Ostenak, C.A.; Whitty, W.J.; Dietz, R.J.

1979-11-01

Preliminary concepts of materials accountability are presented for an internationally safeguarded nuclear-waste geologic repository. A hypothetical reference repository that receives nuclear waste for emplacement in a geologic medium serves to illustrate specific safeguards concepts. Nuclear wastes received at the reference repository derive from prior fuel-cycle operations. Alternative safeguards techniques ranging from item accounting to nondestructive assay and waste characteristics that affect the necessary level of safeguards are examined. Downgrading of safeguards prior to shipment to the repository is recommended whenever possible. The point in the waste cycle where international safeguards may be terminate depends on the fissile content, feasibility of separation, and practicable recoverability of the waste: termination may not be possible if spent fuels are declared as waste

Staff Technical Position on consideration of fault displacement hazards in geologic repository design

International Nuclear Information System (INIS)

McConnell, K.I.; Lee, M.P.

1994-09-01

Nuclear Regulatory Commission regulations for the disposal of spent nuclear fuel and high-level radioactive waste in a geologic repository recognize that fault displacement is a potentially adverse condition. However, they do not prohibit designing the geologic repository against the effects of such a potentially adverse condition. This Staff Technical Position recognizes the acceptability of designing the geologic repository to take into account the attendant effects (e.g., displacement) of faults of regulatory concern and expresses the staff's views on what is needed from the US Department of Energy if it chooses to locate structures, systems, and components important to safety or important to waste isolation in areas that contain faults of regulatory concern

Status and development of deep geological repository in Slovak republic from geological point of view

Directory of Open Access Journals (Sweden)

Jozef Franzen

2007-01-01

Full Text Available During the operation of Slovak NPPs, production of approximately 2,300 metric tons of spent fuel expressed as heavy metal (18,654 spent fuel assemblies is expected. In addition, about 5000 metric tons of radioactive waste unfit for near surface repository at Mochovce and destined for a deep geological disposal. The safe and long-term solution of back-end fuel cycle is so highly required.One of the most favorable solutions is Deep Geological Repository (DGR. The site for a DGR, along with repository design and the engineered barrier system must ensure long-term safety of the disposal system.A preliminary set of site-selection criteria for a DGR was proposed in Slovakia, based on worldwide experience and consistent with IAEA recommendations. Main groups of criteria are: 1 geological and tectonic stability of prospective sites; 2 appropriate characteristics of host rock (lithological homogeneity, suitable hydrogeological and geochemical conditions, favourable geotechnical setting, absence of mineral resources, etc.; 3 conflict of interests (natural resources, natural and cultural heritage, protected resources of thermal waters, etc..Based on the previous geological investigations, three distinct areas (five localities were determined as the most prospective sites for construction of a DGR so far. Three of them are built by granitoids rock (Tribeč Mts., Veporske vrchy Mts. and Stolicke vrchy Mts., other consist of sedimentary rock formations (Cerova vrchovina Upland and Rimavska kotlina Basin. Objective for the next investigation stage is to perform more detailed geological characterization of the prospective sites.

Evaluation of geologic and geophysical techniques for surface-to-subsurface projections of geologic characteristics in crystalline rock

International Nuclear Information System (INIS)

1985-07-01

Granitic and gneissic rock complexes are being considered for their potential to contain and permanently isolate high-level nuclear waste in a deep geologic repository. The use of surface geologic and geophysical techniques has several advantages over drilling and testing methods for geologic site characterization in that the techniques are typically less costly, provide data over a wider area, and do not jeopardize the physical integrity of a potential repository. For this reason, an extensive literature review was conducted to identify appropriate surface geologic and geophysical techniques that can be used to characterize geologic conditions in crystalline rock at proposed repository depths of 460 to 1,220 m. Characterization parameters such as rock quality; fracture orientation, spacing; and aperture; depths to anomalies; degree of saturation; rock body dimensions; and petrology are considered to be of primary importance. Techniques reviewed include remote sensing, geologic mapping, petrographic analysis, structural analysis, gravity and magnetic methods, electrical methods, and seismic methods. Each technique was reviewed with regard to its theoretical basis and field application; geologic parameters that can be evaluated; advantages and limitations, and, where available, case history applications in crystalline rock. Available information indicates that individual techniques provide reliable information on characteristics at the surface, but have limited success in projections to depths greater that approximately 100 m. A combination of integrated techniques combines with data from a limited number of boreholes would significantly improve the reliability and confidence of early characterization studies to provide qualitative rock body characteristics for region-to-area and area-to-site selection evaluations. 458 refs., 32 figs., 14 tabs

3D numerical modelling of the thermal state of deep geological nuclear waste repositories

Science.gov (United States)

Butov, R. A.; Drobyshevsky, N. I.; Moiseenko, E. V.; Tokarev, Yu. N.

2017-09-01

One of the important aspects of the high-level radioactive waste (HLW) disposal in deep geological repositories is ensuring the integrity of the engineered barriers which is, among other phenomena, considerably influenced by the thermal loads. As the HLW produce significant amount of heat, the design of the repository should maintain the balance between the cost-effectiveness of the construction and the sufficiency of the safety margins, including those imposed on the thermal conditions of the barriers. The 3D finite-element computer code FENIA was developed as a tool for simulation of thermal processes in deep geological repositories. Further the models for mechanical phenomena and groundwater hydraulics will be added resulting in a fully coupled thermo-hydro-mechanical (THM) solution. The long-term simulations of the thermal state were performed for two possible layouts of the repository. One was based on the proposed project of Russian repository, and another features larger HLW amount within the same space. The obtained results describe the spatial and temporal evolution of the temperature filed inside the repository and in the surrounding rock for 3500 years. These results show that practically all generated heat was ultimately absorbed by the host rock without any significant temperature increase. Still in the short time span even in case of smaller amount of the HLW the temperature maximum exceeds 100 °C, and for larger amount of the HLW the local temperature remains above 100 °C for considerable time. Thus, the substantiation of the long-term stability of the repository would require an extensive study of the materials properties and behaviour in order to remove the excessive conservatism from the simulations and to reduce the uncertainty of the input data.

Long-Term Information Management (LTIM) of Safeguards Data at Geological Repositories

International Nuclear Information System (INIS)

Haddal, R.; Finch, R.; Baldwin, G.

2016-01-01

Full text: The International Atomic Energy Agency (IAEA) has noted that long-term information management (LTIM) of safeguards data at geological repositories will be a significant challenge in the future as information and records management systems evolve and permanent disposal of nuclear materials becomes a high-priority in many countries. Identifying approaches to how information on buried high-level nuclear waste will be managed, handled, organized, archived, read, interpreted, and secured for the long-term (1000 years after repository closure and beyond) will be key to safeguards at repositories). The purpose of this study is to explore various long-term information management systems and how they may or may not be adapted for geological repositories for high-level waste. The study will also examine what types of safeguards-related data should be included in such a system. The study will also consider hypotheses about future needs and analyze the pros and cons of very long-term information management. (author

Sequential evaluation of the potential geologic repository site at Yucca Mountain, Nevada, USA

International Nuclear Information System (INIS)

Bjerstedt, T.W.

1996-01-01

This paper discusses the changes that are planned for the characterization program at Yucca Mountain due to budget changes. Yucca Mountain is the only site being studied in the US for a geologic repository. Funding for the site characterization program at Yucca Mountain program was cut by roughly one half from the 1994 projected budget to complete three major milestones. These project milestones included: (1) a time-phased determination of site suitability, and if a positive finding, (2) completion of an Environmental Impact Statement, and (3) preparation of a License Application to the US NRC to authorize repository construction. In reaction, Yucca Mountain Site Characterization Project has shifted from parallel development of these milestones to a sequenced approach with the site suitability evaluation being replaced with a management assessment. Changes to the regulatory structure for the disposal program are under consideration by DOE and the NRC. The possibility for NRC and Doe to develop a site-specific regulatory structure follows from the National Energy Policy Act of 1992 that authorized the US EPA to develop a site specific environmental standard for Yucca Mountain

Results From an International Simulation Study on Coupled Thermal, Hydrological, and Mechanical (THM) Processes Near Geological Nuclear Waste Repositories

International Nuclear Information System (INIS)

J. Rutqvist; D. Barr; J.T. Birkholzer; M. Chijimatsu; O. Kolditz; Q. Liu; Y. Oda; W. Wang; C. Zhang

2006-01-01

As part of the ongoing international DECOVALEX project, four research teams used five different models to simulate coupled thermal, hydrological, and mechanical (THM) processes near waste emplacement drifts of geological nuclear waste repositories. The simulations were conducted for two generic repository types, one with open and the other with back-filled repository drifts, under higher and lower postclosure temperatures, respectively. In the completed first model inception phase of the project, a good agreement was achieved between the research teams in calculating THM responses for both repository types, although some disagreement in hydrological responses is currently being resolved. In particular, good agreement in the basic thermal-mechanical responses was achieved for both repository types, even though some teams used relatively simplified thermal-elastic heat-conduction models that neglected complex near-field thermal-hydrological processes. The good agreement between the complex and simplified process models indicates that the basic thermal-mechanical responses can be predicted with a relatively high confidence level

Technical progress report: Rhode Island crystalline repository project, calendar year 1985

International Nuclear Information System (INIS)

Vild, B.F.

1985-01-01

A Nuclear Waste Fund established by the Nuclear Waste Policy Act of 1982 provides financial support to affected states to participate in the high-level radioactive waste repository siting program of the US Department of Energy. In Rhode Island, that function is performed by a multidisciplinary Project Review Team consisting of staff from three State agencies. Members of the Review Team attended several meetings in 1985 to voice their concerns directly to DOE. Written comments were also submitted on draft plans and reports. Among the issues raised were inconsistencies in the geologic and environmental data used to screen potential repository sites, the role of Monitored Retrievable Storage (MRS) in the repository program, and regulations regarding the transportation and storage of nuclear waste. The Review Team also began work on a public information booklet describing the repository program in nontechnical terms. That booklet will be distributed widely upon completion

Deep geological repository: Starting communication at potentially suitable sites

International Nuclear Information System (INIS)

Sumberova, Vera

2001-01-01

The siting of a deep geological repository in the Czech Republic is and will be a complicated process, since it is the first siting process of a nuclear facility designed from the start to be located at non-nuclear sites and to be organised under democratic conditions. This presentation describes the concept of radioactive waste and spent nuclear management in the Czech Republic, Communication activities of Radioactive Waste Repository Authority (RAWRA) with local representatives and lessons learned

Safety assessment of geologic repositories for nuclear waste

International Nuclear Information System (INIS)

Bartlett, J.W.; Burkholder, H.C.; Winegardner, W.K.

1977-01-01

Consideration of geologic isolation for final disposition of radioactive wastes has led to the need for evaluation of the safety of the concept. Such evaluations require consideration of factors not encountered in conventional risk analysis: consequences at times and places far removed from the repository site; indirect, complex, and alternative pathways between the waste and the point of potential consequences; a highly limited data base; and limited opportunity for experimental verification of results. R and D programs to provide technical safety evaluations are under way. Three methods are being considered for the probabilistic aspects of the evaluations: fault tree analysis, repository simulation analysis, and system stability analysis. Nuclide transport models, currently in a relatively advanced state of development, are used to evaluate consequences of postulated loss of geologic isolation. This paper outlines the safety assessment methods, unique features of the assessment problem that affect selection of methods and reliability of results, and available results. It also discusses potential directions for future work

Analysis of the processes defining radionuclide migration from deep geological repositories in porous medium

International Nuclear Information System (INIS)

Brazauskaite, A.; Poskas, P.

2004-01-01

Due to the danger of exposure arising from long-lived radionuclides to humans and environment, spent nuclear fuel (SNF) and high level waste (HLW) are not allowed to be disposed of in near surface repositories. There exists an international consensus that such high level and long-lived radioactive wastes are best disposed of in geological repositories using a system of engineered and natural barriers. At present, the geological repository of SNF and HLW has not been realized yet in any country but there is a lot of experience in the assessment of radionuclide migration from deep repositories, investigations of different processes related to the safety of a disposal system. The aim of this study was to analyze the processes related to the radionuclide migration from deep geological repositories in porous medium such as SNF matrix dissolution, release mechanism of radionuclides from SNF matrix, radionuclide solubility, sorption, diffusive, advective transport of radionuclides from the canister and through the engineered and natural barriers. It has been indicated that SNF matrix dissolution, radionuclide solubility and sorption are sensitive to ambient conditions prevailing in the repository. The approaches that could be used for modeling the radionuclide migration from deep repositories in porous medium are also presented. (author)

Retrievability of high-level nuclear waste from geologic repositories - Regulatory and rock mechanics/design considerations

International Nuclear Information System (INIS)

Tanious, N.S.; Nataraja, M.S.; Daemen, J.J.K.

1987-01-01

Retrievability of nuclear waste from high-level geologic repositories is one of the performance objectives identified in 10CFR60 (Code of Federal Regulations, 1985). 10CFR60.111 states that the geologic repository operations area shall be designed to preserve the option of waste retrieval. In designing the repository operations area, rock mechanics considerations play a major role especially in evaluating the feasibility of retrieval operations. This paper discusses generic considerations affecting retrievability as they relate to repository design, construction, and operation, with emphasis on regulatory and rock mechanics aspects

Release consequence analysis for a hypothetical geologic radioactive waste repository in salt

International Nuclear Information System (INIS)

1979-08-01

One subtask conducted under the INFCE program is to evaluate and compare the health and safety impacts of different fuel cycles in which all radioactive wastes (except those from mining and milling) are placed in a geologic repository in salt. To achieve this objective, INFCE Working Group 7 examined the radiologic dose to humans from geologic repositories containing waste arisings as defined for seven reference fuel cycles. This report examines the release consequences for a generic waste repository in bedded salt. The top of the salt formation and the top of the repository are assumed to be 250 and 600 m, respectively, below the surface. The hydrogeologic structure above the salt consists of two aquifers and two aquitards. The aquifers connect to a river 6.2 km from the repository. The regional gradient to the river is 1 m/km in all aquifers. Hydrologic, transport, and dose models were used to model two release scenarios for each fuel cycle, one without a major disturbance and one in which a major geologic perturbation breached the repository immediately after it was sealed. The purpose of the modeling was to predict the rate of transport of radioactive contaminants from the repository through the geosphere to the biosphere, and to determine the potential dose to humans. Of the many radionuclides in the waste, only 129 I and 226 Ra arrived at the river in sufficient concentrations for a measurable dose calculation. Radionuclide concentrations in the ground water pose no threat to man because the ground water is a concentrated brine and it is diluted by a factor of 10 6 to 10 7 upon entering the river

Current status of the Japanese geological repository programme

International Nuclear Information System (INIS)

Kitayama, Kazumi

2007-01-01

The programme for disposal of radioactive waste in Japan is now moving ahead on a number of fronts. On the regulatory side, responsibility for TRU waste disposal has been assigned to NUMO and guidelines for the safety goals for disposal of LLW have been published. NUMO, as the implementer for the deep geological disposal programme, has been developing the special tools for project management that are needed as a result of the decision to adopt a volunteering approach to siting. NUMO is also building up the technical infrastructure for flexible tailoring of site characterisation, repository design and the associated safety assessment to the conditions found in any volunteer site. This work requires openness and transparency in decision-making but, as several sites may need to be investigated in parallel, particular emphasis is placed on operational practicality. (author)

Site characterization information needs for a high-level waste geologic repository

International Nuclear Information System (INIS)

Gupta, D.C.; Nataraja, M.S.; Justus, P.S.

1987-01-01

At each of the three candidate sites recommended for site characterization for High-Level Waste Geologic Repository development, the DOE has proposed to conduct both surface-based testing and in situ exploration and testing at the depths that wastes would be emplaced. The basic information needs and consequently the planned surface-based and in situ testing program will be governed to a large extent by the amount of credit taken for individual components of the geologic repository in meeting the performance objectives and siting criteria. Therefore, identified information to be acquired from site characterization activities should be commensurate with DOE's assigned performance goals for the repository system components on a site-specific basis. Because of the uncertainties that are likely to be associated with initial assignment of performance goals, the information needs should be both reasonably and conservatively identified

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

Energy Technology Data Exchange (ETDEWEB)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-11-15

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

International Nuclear Information System (INIS)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-01-01

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Proceedings of the workshop on radionuclide release scenarios for geologic repositories

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

The safety of radioactive waste disposal in geological formations cannot be verified experimentally. Safety analysis provides the only means to ensure that all risks associated with the waste repositories are acceptably low. The definition of radionuclide release scenarios, as discussed in these proceeedings, is the first step in the safety analysis of waste repositories.

SKI SITE-94, deep repository performance assessment project, summary

International Nuclear Information System (INIS)

1999-01-01

SITE-94 is a comprehensive performance assessment exercise for a hypothetical repository for spent nuclear fuel at a real site in Sweden. SITE-94 was carried out to develop the capability and tools to enable Swedish Nuclear Power Inspectorate (SKI) to review fully the proposals for a deep repository which are expected to be made by the Swedish Nuclear Fuel and Waste Management Company, SKB (the implementor). Sweden is one of the leading countries in the research and development of geological disposal of radioactive waste. The developed methodology for performance assessment has attracted interests from other countries. The Summary of the main report of the SITE-94 project is translated here into Japanese to allow to make the information on the methodology and the related issues available among Japanese concerned. (author)

Impact on geologic repository usage from limited actinide recycle in pressurized light water reactors

International Nuclear Information System (INIS)

Wigeland, Roald A.; Bauer, Theodore H.; Hill, Robert N.; Stillman, John A.

2007-01-01

A project has been conducted as part of the U.S. Department of Energy Advanced Fuel Cycle Initiative to evaluate the impact of limited actinide recycling in light water reactors on the utilization of a geologic repository where loading of the repository is constrained by the decay heat of the emplaced materials. In this study, it was assumed that spent PWR fuel was processed, removing the uranium, plutonium, americium, and neptunium, along with the fission products cesium and strontium. Previous work had demonstrated that these elements were responsible for limiting loading in the repository based on thermal constraints. The plutonium, americium, and neptunium were recycled in a PWR, with process waste and spent recycled fuel being sent to the repository. The cesium and strontium were placed in separate storage for 100-300 years to allow for decay prior to disposal. The study examined the effect of single and multiple recycles of the recovered plutonium, americium, and neptunium, as well as different processing delay times. The potential benefit to the repository was measured by the increase in utilization of repository space as indicated by the allowable linear loading in the repository drifts (tunnels). The results showed that limited recycling would provide only a small fraction of the benefit that could be achieved with repeated processing and recycling, as is possible in fast neutron reactors. (author)

Radioactive waste disposal programme and siting regions for geological deep repositories. Executive summary. November 2008

International Nuclear Information System (INIS)

2008-11-01

There are radioactive wastes in Switzerland. Since many decades they are produced by the operation of the five nuclear power plants, by medicine, industry and research. Important steps towards the disposal of these wastes are already realized; the corresponding activities are practised. This particularly concerns handling and packaging of the radioactive wastes, their characterization and inventory, as well as the interim storage and the inferred transportations. Preparatory works in the field of scientific research on deep geological repositories have allowed to acquire high level of technical and scientific expertise in that domain. The feasibility of building long-term safe geological repositories in Switzerland was demonstrated for all types of radioactive wastes; the demonstration was accepted by the Federal Council. There is enough knowledge to propose geological siting regions for further works. The financial funds already accumulated guaranty the financing of the dismantling of the power plants as well as building deep geological repositories for the radioactive wastes. The regulations already exist and the organisational arrangements necessary for the fruitful continuation of the works already done have been taken. The programme of the disposal of radioactive wastes also describes the next stages towards the timely realization of the deep repositories as well as the level of the financial needs. The programme is updated every five years, checked by the regulatory bodies and accepted by the Federal Council who reports to the parliament. The process of choosing a site, which will be completed in the next years, is detailed in the conceptual part of the programme for deep geological repositories. The NAGRA proposals are based exclusively on technical and scientific considerations; the global evaluation taking into account also political considerations has to be performed by the authorities and the Federal Council. The programme states that at the beginning of

Project Guarantee 1985. Repository for low- and intermediate-level radioactive waste: construction and operation

International Nuclear Information System (INIS)

Anon.

1985-01-01

A constructional engineering project study aimed at clarification of the feasibility of a repository for low- and intermediate-level radioactive waste (type B repository) has been carried out; the study is based on a model data-set derived from the geological, rock mechanical and topographical characterictics of one of Nagra's planned exploration areas. Final storage is effected in subterranean rock caverns accessed by horizontal tunnel. The reception area also is sited below the surface. Storage is conceived in such a way that, after closure of the repository, maintenance and supervision can be dispensed with and a guarantee of high long-term safety can nevertheless be provided. The envisaged repository consists of an entry tunnel for road vehicles and a reception area with a series of caverns for receiving waste, for additional technical facilities and for the production of the concrete back-fill material. The connecting tunnel is serviced by a tunnel railway and the actual repository area consists of several storage caverns. The repository is intended to accomodate a total of 200'000 m3 of solidified low- and intermediate-level waste. Valanginian marl is assumed as the host rock, although it would also be basically possible to house the proposed installations in other host rocks. The excavated material will total around 1'000'000 m3. The construction time for the whole installation is estimated as about 7 years and a working team of around 30 people will be required for the estimated 60-year operational duration. The project described in the present report justifies the conclusion that construction of a repository for low-and intermediate-level radioactive waste is feasible with present-day technology. This conclusion takes into consideration quantitative and operational constraints as well as geological and hydrogeological data relevant to constructional engineering. The latter are derived from a model data-set based on a specific locality

Stockholm international conference 2003 on geological repositories: Political and technical progress

International Nuclear Information System (INIS)

2004-01-01

The conference reviewed global progress made as well as current perspectives on the activities to develop geologic repositories. The objectives were to review the progress in policy making as well as technical issues and to strengthen international co-operation on waste management and disposal issues. The first day of the conference addressed the policy aspects of geological repositories and the second day featured the more technical issues. Session 1: International progress in performing long-term safety studies and security of geological disposal were discussed and reviewed with examples from OECD/NEA, Belgium, Sweden, USA, Switzerland and Russia. Session 2: Views on stakeholder involvement and decision making process were presented by international organisations and national implementers from Japan, United Kingdom, Belgium and OECD/NEA. Session 3: Views on stakeholder involvement and decision making process were presented by regional and local stakeholders from France, Finland, Korea and Sweden. Session 4: International instruments assisting in the implementation of geological repositories were discussed, for example ICRP and IAEA/NEA safety documents, Joint Convention, Safeguard agreements, Nuclear Liability Conventions, etc. Session 5: The contribution of Research, Development and Demonstration was discussed with overviews of the progress achieved on scientific and technical issues over the past four years. Progress and key issues were presented from Switzerland, USA, Finland, Japan, Sweden and IAEA. Each of the papers and poster presentations have been analysed and indexed separately

Environmental impact assessments and geological repositories for radioactive waste

International Nuclear Information System (INIS)

O'Sullivan, P.; McKirdy, B.; Askarieh, M.; Bond, A.; Russell, S.

1999-01-01

Since 1985 it has been obligatory that facilities in the European Union designed for the permanent storage or disposal of radioactive waste be assessed to determine their effects on the environment. This assessment must be undertaken in advance of any decision by national authorities to give consent for development work to proceed. Member States are given wide discretion on how the above requirements are implemented in practice, e.g. the relevant European Council Directives call for the results of the environmental assessment to be made available to the public before development consent is granted but the detailed arrangements for dissemination of such information and procedures for public consultation are determined by individual Member States. Although the Directives require an assessment of the direct and indirect effects of a project on human beings and on various elements of the natural environment, they are non-specific as to what particular impacts should be addressed, particularly as regards the effects of a project on human beings. Therefore, for example, each Member State may decide whether or not social, health and economic impacts should be included in the assessment. This paper discusses the above issues. It proposes a model approach to environmental impact assessment in the context of geological repositories, including the role of the assessment on the overall decision processes for repository development, the scope and content of the assessment report, and approaches to public involvement

Proposal for geological site selection for L/ILW and HLW repositories. Statement of requirements, procedure and results. Technical report 08-03

International Nuclear Information System (INIS)

2008-10-01

Important steps in the process of managing radioactive wastes have already been implemented in Switzerland. These include the handing and packaging of the waste, waste characterisation and documentation of waste inventories and interim storage along with associated transport. In terms of preparing for deep geological disposal, the necessary scientific and technical work is well advanced and the feasibility of constructing geological repositories that provide the required long-term safety has been successfully demonstrated for all waste types arising in Switzerland. Sufficient knowledge is available to allow the next steps in the selection of repository sites to be defined. The legal framework is also in place and organisational measures have been provided that will allow the tasks to be performed in the coming years to be implemented efficiently. The selection of geological siting regions and sites for repositories in Switzerland will be conducted in three stages. Stage 1 ends with the definition of geological siting regions within which the repository projects will be elaborated in more detail in stages 2 and 3. This report documents and justifies the siting proposals prepared by Nagra for the repositories for low- and intermediate-level waste (L/ILW) and high-level waste (HLW). Formulation of these proposals is conducted in five steps: 1) The waste inventory, which includes reserves for future developments, is allocated to the L/ILW and HLW repositories; 2) Based on this waste allocation, the second step involves defining the barrier and safety concepts for the two repositories. With a view to evaluating the geological siting possibilities, quantitative and qualitative guidelines and requirements on the geology are derived on the basis of these concepts. These relate to the time period to be considered, the space requirements for the repository, the properties of the host rock (depth, thickness, lateral extent, hydraulic conductivity), long-term stability

Project Guarantee 1985. Repository for high-level radioactive waste: construction and operation

International Nuclear Information System (INIS)

Anon.

1985-01-01

An engineering project study aimed at demonstrating the feasibility of constructing a deep repository for high-level waste (Type C repository) has been carried out; the study is based on a model data-set representing typical geological and rock mechanical conditions as found outside the so-called Permocarboniferous basin in the regions under investigation by Nagra in Cantons Aargau, Schaffhausen, Solothurn and Zuerich. The repository is intended for disposal of high-level waste and any intermediate-level waste from re-processing in which the concentration of long-lived alpha-emitters exceeds the permissible limits set for a Type B repository. Final disposal of high-level waste is in subterranean, horizontally mined tunnels and of intermediate-level waste in underground vertical silos. The repository is intended to accomodate a total of around 6'000 HWL-cylinders (gross volume of around 1'200 m3) and around 10'000 m3 of intermediate-level waste. The total excavated volume is around 1'100'000 m3 and a construction time for the whole repository (up to the beginning of emplacement) of around 15 years is expected. For the estimated 50-year emplacement operations, a working team of around 60 people will be needed and a team of around 160 for the simultaneous tunnelling operations and auxiliary work. The project described in the present report permits the conclusion that construction of a repository for high-level radioactive waste and, if necessary, spent fuel-rods is feasible with present-day technology

United States of America activities relative to the International Atomic Energy Agency (IAEA) initiative: Records management for deep geologic repositories

Energy Technology Data Exchange (ETDEWEB)

Warner, P.J.

1997-03-01

The International Atomic Energy Agency (IAEA) has conducted consultant and advisory meetings to prepare a Technical Document which is intended to provide guidance to all IAEA Member States (otherwise known as countries) that are currently planning, designing, constructing or operating a deep or near surface geological repository for the storage and protection of vitrified high-level radioactive waste, spent fuel waste and TRU-waste (transuranic). Eleven countries of the international community are presently in various stages of siting, designing, or constructing deep geologic repositories. Member States of the IAEA have determined that the principle safety of such completed and operation sites must not rely solely on long term institutional arrangements for the retention of information. It is believed that repository siting, design, operation and postoperation information should be gathered, managed and retained in a manner that will provide information to future societies over a very long period of time. The radionuclide life is 10,000 years thus the retention of information must outlive current societies, languages, and be continually migrated to new technology to assure retrieval. This presentation will provide an overview of the status of consideration and implementation of these issues within the United States efforts relative to deep geologic repository projects.

United States of America activities relative to the International Atomic Energy Agency (IAEA) initiative: Records management for deep geologic repositories

International Nuclear Information System (INIS)

Warner, P.J.

1997-01-01

The International Atomic Energy Agency (IAEA) has conducted consultant and advisory meetings to prepare a Technical Document which is intended to provide guidance to all IAEA Member States (otherwise known as countries) that are currently planning, designing, constructing or operating a deep or near surface geological repository for the storage and protection of vitrified high-level radioactive waste, spent fuel waste and TRU-waste (transuranic). Eleven countries of the international community are presently in various stages of siting, designing, or constructing deep geologic repositories. Member States of the IAEA have determined that the principle safety of such completed and operation sites must not rely solely on long term institutional arrangements for the retention of information. It is believed that repository siting, design, operation and postoperation information should be gathered, managed and retained in a manner that will provide information to future societies over a very long period of time. The radionuclide life is 10,000 years thus the retention of information must outlive current societies, languages, and be continually migrated to new technology to assure retrieval. This presentation will provide an overview of the status of consideration and implementation of these issues within the United States efforts relative to deep geologic repository projects

Reference design description for a geologic repository. Revision 02

International Nuclear Information System (INIS)

1999-01-01

This Reference Design Description explains the current design for a potential geologic repository that may be located at Yucca Mountain in Nevada. It describes the proposed design for a surface facility, subsurface repository, and waste packaging; it also presents the current design of the key engineering systems for the final four phases: operations, monitoring, closure, and postclosure. In addition, this Reference Design Description reviews the expected long-term performance of the potential repository. In accordance with current law, this design does not include an interim storage option. This document has six major sections. Section 1 describes the physical layout of the proposed repository. The second section describes the 4-phase evolution of the development of the proposed repository. Section 3 describes the reception of waste from offsite locations. The fourth section details the various systems that will package the waste and move it below ground as well as safety monitoring and closure. Section 5 describes the systems (both physical and analytical) that ensure continued safety after closure. The final section offers design options that may be adopted to increase the margin of safety

International Conference on Geological Repositories 2016. Conference Synthesis, 7-9 December 2016, Paris, France

International Nuclear Information System (INIS)

Walke, Russell; Kwong, Gloria; )

2017-01-01

Worldwide consensus exists within the international community that geological repositories can provide the necessary long-term safety and security to isolate long-lived radioactive waste from the human environment over long timescales. Such repositories are also feasible to construct using current technologies. However, proving the technical merits and safety of repositories, while satisfying societal and political requirements, has been a challenge in many countries. Building upon the success of previous conferences held in Denver (1999), Stockholm (2003), Berne (2007) and Toronto (2012), the ICGR 2016 brought together high-level decision makers from regulatory and local government bodies, waste management organisations and public stakeholder communities to review current perspectives of geological repository development. This publication provides a synthesis of the 2016 conference on continued engagement and safe implementation of repositories, which was designed to promote information and experience sharing, particularly in the development of polices and regulatory frameworks. Repository safety, and the planning and implementation of repository programs with societal involvement, as well as ongoing work within different international organisations, were also addressed at the conference. (authors)

Regional and site geological frameworks : proposed Deep Geologic Repository, Bruce County, Ontario

Energy Technology Data Exchange (ETDEWEB)

Raven, K.; Sterling, S.; Gaines, S.; Wigston, A. [Intera Engineering Ltd., Ottawa, ON (Canada); Frizzell, R. [Nuclear Waste Management Organization, Toronto, ON (Canada)

2009-07-01

The Nuclear Waste Management Organization is conducting geoscientific studies on behalf of Ontario Power Generation into the proposed development of a Deep Geologic Repository (DGR) for low and intermediate level radioactive waste (L and ILW) at the Bruce site, near Tiverton, Ontario. This paper presented a regional geological framework for the site that was based on a review of regional drilling; structural geology; paleozoic stratigraphy and sedimentology; a 3D geological framework model; a DGR geological site characterization model; bedrock stratigraphy and marker beds; natural fracture frequency data; and formation predictability. The studies have shown that the depth, thickness, orientation and rock quality of the 34 rock formations, members or units that comprise the 840 m thick Paleozoic bedrock sequence at the Bruce site are very uniform and predictable over distances of several kilometres. The proposed DGR will be constructed as an engineered facility comprising a series of underground emplacement rooms at a depth of 680 metres below ground within argillaceous limestones. The geoscientific studies are meant to provide a basis for the development of descriptive geological, hydrogeological and geomechanical models of the DGR site that will facilitate environmental and safety assessments. 11 refs., 3 tabs., 9 figs.

Spent fuel performance in geologic repository environments

International Nuclear Information System (INIS)

Bradley, D.J.

1985-10-01

The performance assessment of the waste package is a current area of study in the United States program to develop a geologic repository for nuclear waste isolation. The waste package is presently envisioned as the waste form and its surrounding containers and possibly a packing material composed of crushed host rock or mixtures of that rock with clays. This waste package is tied to performance criteria set forth in recent legislation. It is the goal of the Civilian Radioactive Waste Management Program to obtain the necessary information on the waste package, in several geologic environments, to show that the waste package provides reasonable assurance of meeting established performance criteria. This paper discusses the United States program directed toward managing high-level radioactive waste, with emphasis on the current effort to define the behavior of irradiated spent fuel in repository groundwaters. Current studies are directed toward understanding the rate and nature (such as valence state, colloid form if any, solid phase controlling solubility) of radionuclide release from the spent fuel. Due to the strong interactive effect of radiation, thermal fields, and waste package components on this release, current spent fuel studies are being conducted primarily in the presence of waste package components over a wide range of potential environments

Environmental impact assessments and geological repositories: A model process

International Nuclear Information System (INIS)

Webster, S.

2000-01-01

In a recent study carried out for the European Commission, the scope and application of environmental impact assessment (EIA) legislation and current EIA practice in European Union Member States and applicant countries of Central and Eastern Europe was investigated, specifically in relation to the geological disposal of radioactive waste. This paper reports the study's investigations into a model approach to EIA in the context of geological repositories, including the role of the assessment in the overall decision processes and public involvement. (author)

Geotechnical support and topical studies for nuclear waste geologic repositories: Annual report, fiscal year 1987

International Nuclear Information System (INIS)

1988-01-01

This multidisciplinary project was initiated in fiscal year 1986. It comprises 11 reports in two major interrelated tasks: The technical assistance part of the project includes reviewing the progress of the major projects in the DOE Office of Civilian Radioactive waste Management (OCRWM) Program and advising the Engineering and Geotechnology Division on significant technical issues facing each project; analyzing geotechnical data, reports, tests, surveys and plans for the different projects; reviewing and commenting on major technical reports and other program documents such as Site Characterization Plans (SCP) and Study Plans; and providing scientific and technical input at technical meetings. The topical studies activity comprises studies on scientific and technical ions and issues of significance to in-situ testing, test analysis methods, and site characterization of nuclear waste geologic repositories. The subjects of study were selected based on discussions with DOE staff. One minor topic is a preliminary consideration and planning exercise for postclosure monitoring studies. The major task, with subtasks involving various geoscience disciplines, is a study of the mechanical, hydraulic, geophysical and geochemical properties of fractures in geologic rock masses

Development of an international safeguards approach to the final disposal of spent fuel in geological repositories

International Nuclear Information System (INIS)

Murphey, W.M.; Moran, B.W.; Fattah, A.

1996-01-01

The International Atomic Energy Agency (IAEA) is currently pursuing development of an international safeguards approach for the final disposal of spent fuel in geological repositories through consultants meetings and through the Program for Development of Safeguards for Final Disposal of Spent Fuel in Geological Repositories (SAGOR). The consultants meetings provide policy guidance to IAEA; SAGOR recommends effective approaches that can be efficiently implemented by IAEA. The SAGOR program, which is a collaboration of eight Member State Support Programs (MSSPs), was initiated in July 1994 and has identified 15 activities in each of three areas (i.e. conditioning facilities, active repositories, and closed repositories) that must be performed to ensure an efficient, yet effective safeguards approach. Two consultants meetings have been held: the first in May 1991 and the last in November 1995. For nuclear materials emplaced in a geological repository, the safeguards objectives were defined to be (1) to detect the diversion of spent fuel, whether concealed or unconcealed, from the repository and (2) to detect undeclared activities of safeguards concern (e.g., tunneling, underground reprocessing, or substitution in containers)

A safeguards approach for a closed geological repository for spent fuel

International Nuclear Information System (INIS)

Meer, K. van der; Carchon, R.

1999-01-01

After closure of a geological repository a diversion of fissile material can only take place by excavating spent fuel containers and bringing them to the surface. Therefore mining activities are required, either by reopening the original shaft, by creating a new shaft or by approaching the containers underground via a neighbouring mine The recovery time of the stored spent fuel plays an important role in the determination of the timeliness criterion and, therefore, the inspection frequency of the site. Obviously, this frequency can create a financial constraint due to the infinite character of the spent fuel storage in a geological repository. Anomalies for detection of a possible diversion are undeclared mining activities. The safeguards approach has to assure Continuity Of Knowledge (COK) of the fissile material. By consequence, a safeguards approach that is developed for a closed repository, is influenced by the safeguards approach applied to an open. repository and a conditioning facility. A closed repository is verified by DIV. To perform the DIV satellite monitoring could be performed for surface verification and e.g. seismic techniques could be used for verification that no undeclared mining activities underground take place. Visual inspections of the site by inspectors have to reveal concealment methods used by a potential diverter. These measures should guarantee that the disposed spent fuel remains untouched. (author)

Albedo Neutron Dosimetry in a Deep Geological Disposal Repository for High-Level Nuclear Waste.

Science.gov (United States)

Pang, Bo; Becker, Frank

2017-04-28

Albedo neutron dosemeter is the German official personal neutron dosemeter in mixed radiation fields where neutrons contribute to personal dose. In deep geological repositories for high-level nuclear waste, where neutrons can dominate the radiation field, it is of interest to investigate the performance of albedo neutron dosemeter in such facilities. In this study, the deep geological repository is represented by a shielding cask loaded with spent nuclear fuel placed inside a rock salt emplacement drift. Due to the backscattering of neutrons in the drift, issues concerning calibration of the dosemeter arise. Field-specific calibration of the albedo neutron dosemeter was hence performed with Monte Carlo simulations. In order to assess the applicability of the albedo neutron dosemeter in a deep geological repository over a long time scale, spent nuclear fuel with different ages of 50, 100 and 500 years were investigated. It was found out, that the neutron radiation field in a deep geological repository can be assigned to the application area 'N1' of the albedo neutron dosemeter, which is typical in reactors and accelerators with heavy shielding. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Safeguarding of spent fuel conditioning and disposal in geological repositories

International Nuclear Information System (INIS)

Forsstroem, H.; Richter, B.

1997-01-01

Disposal of spent nuclear fuel in geological formations, without reprocessing, is being considered in a number of States. Before disposal the fuel will be encapsulated in a tight and corrosion resistant container. The method chosen for disposal and the design of the repository will be determined by the geological conditions and the very strict requirements on long-term safety. From a safeguards perspective spent fuel disposal is a new issue. As the spent fuel still contains important amounts of material under safeguards and as it can not be considered practicably irrecoverable in the repository, the IAEA has been advised not to terminate safeguards, even after closure of the repository. This raises a number of new issues where there could be a potential conflict of interests between safety and safeguards demands, in particular in connection with the safety principle that burdens on future generations should be avoided. In this paper some of these issues are discussed based on the experience gained in Germany and Sweden about the design and future operation of encapsulation and disposal facilities. The most important issues are connected to the required level of safeguards for a closed repository, the differences in time scales for waste management and safeguards, the need for verification of the fissile content in the containers and the possibility of retrieving the fuel disposed of. (author)

The general situation of clay site for high-level waste geological disposal repository

International Nuclear Information System (INIS)

Wang Changxuan; Liu Xiaodong; Liu Pinghui

2008-01-01

Host medium is vitally important for safety of high-level radiaoactive waste (HLW) geological disposal. Clay, as host media of geological repository of HLW, has received greater attention for its inherent advantages. This paper summarizes IAEA and OECD/NEA's some safety guides on site selection and briefly introduces the process of the site selection, their studies and the characteristics of the clay formations in Switz-erland, France and Belgian. Based on these analyses, some suggestions are made to China's HLW repository clay site selection. (authors)

Salt repository project: Technical progress report for the quarter 1 April--30 June 1987

International Nuclear Information System (INIS)

1987-01-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of Energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation

Salt Repository Project technical progress report for the quarter 1 January--31 March 1987

International Nuclear Information System (INIS)

1988-03-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation. 23 refs., 1 fig

Establishment of IAEA knowledge of integrity of the geological repository boundaries and disposed spent fuel assemblies in the context of the Finnish geological repository. Experts' Group meeting Report on Task JNT/C 1204 of the Member States' Support Programme to IAEA Safeguards

International Nuclear Information System (INIS)

Okko, O.

2004-05-01

The Geological Repository Safeguards Experts Group (Member State Support Programme tasks JNT/C1204 and C1226), agreed that annual meetings should be held to address interface issues between IAEA safeguards and radioactive waste management and to explore the use of safety and operational information to make International Atomic Energy Agency (IAEA) safeguards more effective and efficient for geological repository facilities. It has also been recognised that the safeguards measures for geological repositories are to be developed site-specifically. To address these issues to the planned Olkiluoto repository in Finland a meeting of experts in safety, geological repository operations,and safeguards from 6 States, European Commission, and IAEA was held in Olkiluoto and Rauma, Finland, during September 29 - October 4, 2003. The pre-operational phase of the Olkiluoto repository should be efficiently used by the parties involved in safeguards. The applicability and reliability of the potential new techniques and the efficient practices must be developed and proven before their implementation as safeguards measures to be applied at the subsequent stages of the repository development. The visit to the location of the proposed Olkiluoto repository and neighbouring areas and subsequent presentations enabled the working groups to discuss the various issues with reference to actual site conditions. The working groups were thus able to identify potential measurement and monitoring techniques and research and development requirements for consideration by the Finnish authorities, in addition to making recommendations to the IAEA on planned activities for carrying out before and during the early investigation phase of the proposed Olkiluoto repository. It was understood that all parties shall take good care of the implementation of the planned activities to ensure that proven means, approaches and the required verified information is at hand at the time the projected facility will

NAGRA - Sites for geological repositories - Technical safety factors: Suggestions for stage 3

International Nuclear Information System (INIS)

2015-01-01

This comprehensive brochure published by the Swiss National Cooperative for the Disposal of Radioactive Waste (NAGRA) examines the six sites for repositories for nuclear wastes in Switzerland which have been proposed in Stage 1 of the program concerning nuclear waste repositories. Three of these sites are proposed for both highly radioactive wastes as well as for low and medium-active wastes, the other three for low and medium-active wastes only. The evaluation of the sites is discussed. The sites are to be further evaluated in Stage 2 of the program. The work to be done in the further stages involved in the selection of the final site (or sites) is described. Along with definition of the regions where deep repositories could possibly be built, suggestions for the placing of the facilities required on the surface are discussed. Geological requirements on the repositories and safety-relevant characteristics of the various site options are discussed. The results of the assessments made are presented in tabular form. Maps and geological cross-sections of all the suggested areas are included

Canada's deep geological repository for used nuclear fuel - update on the site evaluation process and interweaving of aboriginal traditional knowledge

International Nuclear Information System (INIS)

Watts, B.; Belfadhel, M.B.; Facella, J.

2015-01-01

The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for the long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository (DGR) in a suitable crystalline or sedimentary rock formation. In May 2010, the NWMO initiated a nine-step site selection process to seek an informed and willing community to host Canada's deep geological repository. As of April 2015, twenty-two communities expressed interest in learning more about the project. This paper provides an update on the site evaluation process and describes the approach, methods and criteria used in the assessments, focusing on geological and community well-being studies. Engagement and field activities to interweave Aboriginal Traditional Knowledge with western science are also discussed. (author)

Canada's deep geological repository for used nuclear fuel - site selection process update

International Nuclear Information System (INIS)

Facella, J.

2014-01-01

In 2007, the Government of Canada selected Adaptive Phased Management as Canada's plan for the long-term management of Canada's used nuclear fuel in a deep geological repository, located in an informed and willing host. The process of site selection is an important milestone in this program. The NWMO describes its approach to working collaboratively with communities which expressed interest in exploring the project, as well as Aboriginal communities in the area and other surrounding communities. The project is designed to be implemented through a long-term partnership involving the interested community, Aboriginal communities and surrounding communities working with the NWMO. (author)

Seismic stability of the survey areas of potential sites for the deep geological repository of the spent nuclear fuel

Czech Academy of Sciences Publication Activity Database

Kaláb, Zdeněk; Šílený, Jan; Lednická, Markéta

2017-01-01

Roč. 15, č. 1 (2017), s. 486-493 E-ISSN 2391-5471 R&D Projects: GA MŠk LM2010008; GA MŠk(CZ) LM2015079 Institutional support: RVO:68145535 ; RVO:67985530 Keywords : deep geological repository * earthquake * seismicity * neo-deterministic analysis * probabilistic seismic hazard assessment Subject RIV: DC - Siesmology, Volcanology, Earth Structure; DC - Siesmology, Volcanology, Earth Structure (GFU-E) OBOR OECD: Environmental and geological engineering, geotechnics; Environmental and geological engineering, geotechnics (GFU-E) Impact factor: 0.745, year: 2016 https://www.degruyter.com/downloadpdf/j/phys.2017.15.issue-1/phys-2017-0055/phys-2017-0055.pdf

Project Guarantee 1985. Final repository for high-level radioactive wastes: The system of safety barriers

International Nuclear Information System (INIS)

Anon.

1985-01-01

Final disposal of radioactive waste involves preventing the waste from returning from the repository location into the biosphere by means of successively arranged containment measures known as safety barriers. In the present volume NGB 85-04 of the series of reports for Project 'Guarantee' 1985, the safety barrier system for the type C repository for high-level waste is described. The barrier parameters which are relevant for safety analysis are quantified and associated error limits and data scatter are given. The aim of the report is to give a summary documentation of the safety analysis input data and their scientific background. For secure containment of radioactive waste safety barriers are used which effectively limit the release of radioactive material from the repository (release barriers) and effectively retard the entry of the original radioactive material into the biosphere (time barriers). Safety barriers take the form of both technically constructed containment measures and the siting of the repository in suitable geological formations. The technical safety barrier system in the case of high-level waste comprises: the waste solidification matrix (borosilicate glass), massive steel canisters, encasement of the waste canisters, encasement of the waste canisters in highly compacted bentonite, sealing of vacant storage space and access routes on repository closure. The natural geological safety barriers - the host rock and overlying formations provide sufficiently long deep groundwater flow times from the repository location to the earth's surface and for additional lengthening of radionuclide migration times by means of various chemical and physical retardation mechanisms. The stability of the geological formations is so great that hydrogeological system is protected for a sufficient length of time from deterioration caused, in particular, by erosion. Observations in the final section of the report indicate that input data for the type C repository safety

Study on a monitoring strategy to support decision making for geological repository closure

International Nuclear Information System (INIS)

Suyama, Yasuhiro; Tanabe, Hiromi; Eto, Jiro; Yoshimura, Kimitaka

2010-01-01

Japan currently plans to dispose of high-level radioactive wastes (vitrified HLWs) produced from the reprocessing of spent nuclear fuel in deep geological formations, in order to isolate the radioactive wastes from the human environment for tens of thousands of years. Such a geological repository must be designed to ensure operational safety and post-closure safety. Then, following the closure of the geological repository, post-closure safety will be provided by an engineered barrier system (EBS) and a natural barrier system (NBS) without relying on monitoring or institutional control. However, from a technical standpoint, monitoring has been required during backfilling in current studies. Additionally, there has been strong social pressure to continue monitoring during all the phases including post-closure. On the basis of the current situations, a monitoring strategy for geological disposal must be studied to ensure the long term safety of geological disposal. Focusing on decision making for geological repository closure, the authors have created a basic logical structure for the decision making process with the principles for ensuring safety and have developed a monitoring strategy based on the logical structure. The monitoring strategy is founded on three key aspects: the role of monitoring, boundary conditions of monitoring at the time of decision making, and a methodology for monitoring planning. Then, the monitoring strategy becomes a starting point of monitoring planning during site characterization, construction, operation and staged closure, as well as post-closure with institutional control, and of social science studies. (author)

Reference design description for a geologic repository: Revision 01

International Nuclear Information System (INIS)

1997-09-01

This document describes the current design expectations for a potential geologic repository that could be located at Yucca Mountain in Nevada. This Reference Design Description (RDD) looks at the surface and subsurface repository and disposal container design. Additionally, it reviews the expected long-term performance of the potential repository. In accordance with current legislation, the reference design for the potential repository does not include an interim storage option. The reference design presented allows the disposal of highly radioactive material received from government-owned spent fuel custodian sites; produces high-level waste sites, and commercial spent fuel sites. All design elements meet current federal, state, and local regulations governing the disposal of high-level radioactive waste and protection of the public and the environment. Due to the complex nature of developing a repository, the design will be created in three phases to support Viability Assessment, License Application, and construction. This document presents the current reference design. It will be updated periodically as the design progresses. Some of the details presented here may change significantly as more cost-effective solutions, technical advancements, or changes to requirements are identified

Process for selecting a site for Canada's deep geological repository for used nuclear fuel

International Nuclear Information System (INIS)

Facella, J.; Belfadhel, M.B.

2011-01-01

The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management, the approach selected by the Government of Canada for long-term management of used nuclear fuel waste generated by Canadian nuclear reactors. The ultimate objective of Adaptive Phased Management is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable crystalline or sedimentary rock formation at a depth of about 500m. The repository will consist of a series of access and service shafts and a series of tunnels leading to placement rooms where used fuel will be placed and sealed in competent rock using a multi-barrier system which includes long lived specially designed containers, sealing materials such as bentonite and the rock itself. The used fuel will be monitored throughout all phases of implementation and will also remain retrievable for an extended period of time. In May 2010, the NWMO published the site selection process that serves as the road map to decision-making on the location for the deep geological repository. NWMO initiated the process with a first stage that invites communities to learn more about the project and the site selection process. NWMO is actively building awareness of the project and, on request of communities, is delivering briefings, supporting community capacity building and undertaking high-level screenings of site suitability. The paper provides a brief description of: Adaptive Phased Management including the deep geological repository which is its ultimate goal, and the design of the site selection process, and importantly the approach to assessing the suitability of sites from both a social and technical perspective. The paper will outline how NWMO sought to develop a socially-acceptable site selection process as a firm foundation for future decisions on siting. Through a two-year collaborative process, NWMO sought to understand the expectations of

Plans for characterization of the potential geologic repository site at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Dobson, D.C.; Blanchard, M.B.; Voegele, M.D.; Younker, J.L.

1990-01-01

Site investigations in the vicinity of the potential repository site at Yucca Mountain, Nevada, have occurred for many years. Although information from previous site investigations was adequate to support preliminary evaluations by the US Department of Energy (DOE) in the Environmental Assessment and to develop conceptual repository and waste package designs, this information is insufficient to proceed to the advanced designs and performance assessments required for the license application to the US Nuclear Regulatory Commission (NRC). Therefore, intensive site characterization is planned, as described in the December 1988 Site Characterization Plan (SCP). The data acquisition activities described in the SCP are focused on obtaining information to allow evaluations of the natural and engineered barriers considered potentially relevant to repository performance. The site data base must be adequate to allow predictions of the range of expected variation in geologic conditions over the next 10,000 years, as well as predictions of the probabilities for catastrophic geologic events that could affect repository performance. 4 refs., 4 figs

Kincardine deep geologic repository proposal and the public

International Nuclear Information System (INIS)

Squire, T.

2005-01-01

'Full text:' In 2002, the Municipality of Kincardine and OPG signed a Memorandum of Understanding (MOU) regarding the long-term management of low and intermediate level radioactive wastes. The purpose of the MOU was for OPG, in consultation with Kincardine, to develop a plan for the long-term management of low and intermediate level waste at OPG's Western Waste Management Facility (WWMF) located on the Bruce site. An independent assessment, which included geotechnical feasibility and safety analyses, a community attitude survey and interviews with local residents, businesses and tourists, and economic modeling to determine the potential benefits and impacts, was completed in February 2004. Ultimately, Kincardine Council endorsed a resolution (Kincardine Council no. 2004-232) to: 'endorse the opinion of the Nuclear Waste Steering Committee and select the 'Deep Rock Vault' option as the preferred course of study in regards to the management of low and intermediate level radioactive waste'. The surrounding municipalities of Saugeen Shores, Brockton, Arran-Elderslie, and Huron-Kinloss expressed their support for the Deep Geologic Repository proposal. This presentation discusses the history, major steps and public processes surrounding the Kincardine Deep Geologic Repository proposal. (author)

LISA: A performance assessment code for geological repositories of radioactive waste

International Nuclear Information System (INIS)

Bertozzi, G.; Saltelli, A.

1985-01-01

LISA, developed at JRC-Ispra, is a statistical code, which calculates the radiation exposures and risks associated with radionuclide releases from geological repositories of nuclear waste. The assessment methodology is described briefly. It requires that a number of probabilistic components be quantified and introduced in the analysis; the results are thus expressed in terms of risk. The subjective judgment of experts may be necessary to quantify the probabilities of occurrence of rare geological events. Because of large uncertainties in input data, statistical treatment of the Monte Carlo type is utilized for the analysis; thus, the output from LISA is obtained in the form of distributions. A few results of an application to a probabilistic scenario for a repository mined in a clay bed are illustrated

Siting regions for deep geological repositories. Nagra’s proposals for stage 3

International Nuclear Information System (INIS)

2014-01-01

This brochure published by the Swiss National Cooperative for the Disposal of Radioactive Waste (NAGRA) discusses the selection of sites for deep geological repositories for nuclear wastes in Switzerland. The procedure proposed for the selection process is explained. The four sites for possible repositories of high-level radioactive waste as well as for low and intermediate-level wastes are described and rated with respect to the various safety factors involved. The reasons for the long-term safety measures proposed and the geological barriers involved are discussed. The four proposals for depository sites are looked at in more detail. The paper is well illustrated with several diagrams and tables

Assessing the potentialities of integrated modelling during early phases of siting and design of a geological repository: the REGIME exercise

Energy Technology Data Exchange (ETDEWEB)

Genty, A.; Certes, C.; Serres, C.; Besnus, F. [Institut de Radioprotection et de Surete Nucleaire IRSN, 92 - Fontenay aux Roses (France); Fischer-Appelt, K.; Baltes, B.; Rohlig, J. [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), Koeln (Germany)

2003-01-01

This paper presents the safety assessment exercise 'REGIME' (Repository Evaluation performed by GRS and IRSN through a Modelling Exercise) performed jointly by GRS and IRSN. The main objective of the project is to test the ability of integrated modelling to contribute to site selection and repository conception in the context of high-level radioactive waste disposal. The project is divided in two parts. Phase 1 consisted in studying different flow patterns in a given geological context. The selected hydrogeological contexts and three site locations potentially favourable for hosting a repository are described. Phase 2, under progress, aims at evaluating the rote of limitation of releases played by the different components of the disposal system taking into account possible dysfunctions. The main issues to be addressed in phase 2, the modelling outline and the scenarios to be studied are presented. (authors)

Region-to-area screening methodology for the Crystalline Repository Project

International Nuclear Information System (INIS)

1985-04-01

The purpose of this document is to describe the Crystalline Repository Project's (CRP) process for region-to-area screening of exposed and near-surface crystalline rock bodies in the three regions of the conterminous United States where crystalline rock is being evaluated as a potential host for the second nuclear waste repository (i.e., in the North Central, Northeastern, and Southeastern Regions). This document indicates how the US Department of Energy's (DOE) General Guidelines for the Recommendation of Sites for Nuclear Waste Repositories (10 CFR 960) were used to select and apply factors and variables for the region-to-area screening, explains how these factors and variable are to be applied in the region-to-area screening, and indicates how this methodology relates to the decision process leading to the selection of candidate areas. A brief general discussion of the screening process from the national survey through area screening and site recommendation is presented. This discussion sets the scene for detailed discussions which follow concerning the region-to-area screening process, the guidance provided by the DOE Siting Guidelines for establishing disqualifying factors and variables for screening, and application of the disqualifying factors and variables in the screening process. This document is complementary to the regional geologic and environmental characterization reports to be issued in the summer of 1985 as final documents. These reports will contain the geologic and environmental data base that will be used in conjunction with the methodology to conduct region-to-area screening

Site selection factors for repositories of solid high-level and alpha-bearing wastes in geological formations

International Nuclear Information System (INIS)

1977-01-01

The purpose of this report is to provide guidelines for the selection and evaluation of suitable areas and sites for the disposal of solid high-level and alpha-bearing wastes into geological formations. This report is also intended to provide summary information on many types of geological formations underlying the land masses that might be considered as well as guidance on the geological and hydrological factors that should be investigated to demonstrate the suitability of the formations. In addition, other factors that should be considered in selecting a site for a radioactive waste repository are discussed briefly. The information, as presented, was developed to the extent of current technology for application to the evaluation of deep (greater than about 300 metres below ground level) geological formations in the selection of suitable areas for the disposal of solid or solidified high-level and alpha-bearing wastes. The extreme complexity of many geological environments and of the rock features that govern the presence and circulation of groundwater does not make it feasible to derive strict criteria for the selection of a site for a radioactive waste repository in a geological formation. Each potential repository location must be evaluated according to its own unique geological and hydrological setting. Therefore, only general guidance is offered, and this is done through discussion of the many factors that need to be considered in order to obtain the necessary assurances that the radionuclides will be confined in the geological repository over the required period of time

Site selection factors for repositories of solid high-level and alpha-bearing wastes in geological formations

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

The purpose of this report is to provide guidelines for the selection and evaluation of suitable areas and sites for the disposal of solid high-level and alpha-bearing wastes into geological formations. This report is also intended to provide summary information on many types of geological formations underlying the land masses that might be considered as well as guidance on the geological and hydrological factors that should be investigated to demonstrate the suitability of the formations. In addition, other factors that should be considered in selecting a site for a radioactive waste repository are discussed briefly. The information, as presented, was developed to the extent of current technology for application to the evaluation of deep (greater than about 300 meters below ground level) geological formations in the selection of suitable areas for the disposal of solid or solidified high-level and alpha-bearing wastes. The extreme complexity of many geological environments and of the rock features that govern the presence and circulation of groundwater does not make it feasible to derive strict criteria for the selection of a site for a radioactive waste repository in a geological formation. Each potential repository location must be evaluated according to its own unique geological and hydrological setting. Therefore, only general guidance is offered, and this is done through discussion of the many factors that need to be considered in order to obtain the necessary assurances that the radionuclides will be confined in the geological repository over the required period of time.

Systems engineering management plan for the Salt Repository Project

International Nuclear Information System (INIS)

Neff, J.O.

1986-08-01

This document presents the plan for using systems engineering in conducting and managing the technical work of the Salt Repository Project (SRP) of the US Department of Energy's Civilian Radioactive Waste Management Program. The need for preparing a Systems Engineering Management Plan (SEMP) is traced back to relevant DOE directives. These directives are interpreted as SRP requirements in the context of the Mined Geologic Disposal System. The strategy for conducting systems engineering on the SRP, including the role of the systems engineering process, is then described. The SEMP also designates who in the project organization will be responsible for carrying out the activities. Finally, the management tools that are used to implement the systems engineering process, including associated documentation on the SRP, are described

Environmental remediation of high-level nuclear waste in geological repository. Modified computer code creates ultimate benchmark in natural systems

International Nuclear Information System (INIS)

Peter, Geoffrey J.

2011-01-01

Isolation of high-level nuclear waste in permanent geological repositories has been a major concern for over 30 years due to the migration of dissolved radio nuclides reaching the water table (10,000-year compliance period) as water moves through the repository and the surrounding area. Repositories based on mathematical models allow for long-term geological phenomena and involve many approximations; however, experimental verification of long-term processes is impossible. Countries must determine if geological disposal is adequate for permanent storage. Many countries have extensively studied different aspects of safely confining the highly radioactive waste in an underground repository based on the unique geological composition at their selected repository location. This paper discusses two computer codes developed by various countries to study the coupled thermal, mechanical, and chemical process in these environments, and the migration of radionuclide. Further, this paper presents the results of a case study of the Magma-hydrothermal (MH) computer code, modified by the author, applied to nuclear waste repository analysis. The MH code verified by simulating natural systems thus, creating the ultimate benchmark. This approach based on processes similar to those expected near waste repositories currently occurring in natural systems. (author)

Development of an Integrated Natural Barrier Database System for Site Evaluation of a Deep Geologic Repository in Korea - 13527

International Nuclear Information System (INIS)

Jung, Haeryong; Lee, Eunyong; Jeong, YiYeong; Lee, Jeong-Hwan

2013-01-01

Korea Radioactive-waste Management Corporation (KRMC) established in 2009 has started a new project to collect information on long-term stability of deep geological environments on the Korean Peninsula. The information has been built up in the integrated natural barrier database system available on web (www.deepgeodisposal.kr). The database system also includes socially and economically important information, such as land use, mining area, natural conservation area, population density, and industrial complex, because some of this information is used as exclusionary criteria during the site selection process for a deep geological repository for safe and secure containment and isolation of spent nuclear fuel and other long-lived radioactive waste in Korea. Although the official site selection process has not been started yet in Korea, current integrated natural barrier database system and socio-economic database is believed that the database system will be effectively utilized to narrow down the number of sites where future investigation is most promising in the site selection process for a deep geological repository and to enhance public acceptance by providing readily-available relevant scientific information on deep geological environments in Korea. (authors)

Generic description of facilities at the shaft head (auxiliary entrance installations) of deep geological repositories

International Nuclear Information System (INIS)

2016-10-01

this report, NAGRA assumes that the auxiliary access facilities of a deep geological repository can be realised in compliance with prescribed norms and standards and operated safely. The actual locations of these facilities will be concretised in a later project phase, with the concerns and wishes of the affected region being taken into consideration within certain boundary conditions. (authors)

Site selection for deep geologic repositories - Consequences for society, economy and environment

International Nuclear Information System (INIS)

2010-03-01

In a few years, Switzerland will make the decision regarding site selection for geological underground repositories for the storage of radioactive wastes. Besides the safety issue, many citizens are interested in how such a repository will affect environment, economy and society in the selected site's region. This brochure summarizes the results of many studies on the socio-economic impacts of nuclear waste repositories. Radioactive wastes must be stored in such a way that mankind and environment are safely protected for a long period of time. How this goal may be achieved, is already known: geologic deep repositories warrant long-term safety. For the oncoming years in Switzerland the question is where the repository will be built. The search for an appropriate site for a repository in the proposed regions will launch discussions. Within the participative framework the regions may bring their requests. The demonstration of the safety of potential repository sites has the highest priority in the selection process. In the third procedural step additional rock investigations will be made. The socio-economic studies and the experience with existing plants show that radioactive waste management plants can be built and operated in good agreement with environmental requirements. The radioactive wastes in a deep underground repository are stored many hundred meters below the Earth's surface. There, they are isolated from our vital space. Technical barriers and the surrounding dense rock confinement prevent the release of radioactive materials into the environment. A deep repository has positive consequences for the regional economy. It increases trade and value creation and creates work places. The socio-economic impacts practically extend over one century, but strongly vary with time; they are the largest during the building period. High life quality and a positive population development in the selected site region are compatible with a deep repository. A fair and

Geology and hydrogeology of the proposed nuclear waste repository at Yucca Mountain, Nevada and the surrounding area

International Nuclear Information System (INIS)

Mattson, S.R.; Broxton, D.E.; Buono, A.; Crowe, B.M.; Orkild, P.P.

1989-01-01

In late 1987 Congress issued an amendment to the Nuclear Waste Policy Act of 1982 which directed the characterization of Yucca Mountain, Nevada as the only remaining potential site for the Nation's first underground high-level radioactive waste repository. The evaluation of a potential underground repository is guided and regulated by policy established by the Department of Energy (DOE), Nuclear Regulatory Commission (NRC), Environmental Protection Agency (EPA), Department of Transportation (DOT), and the US Congress. The Yucca Mountain Project is the responsibility of the DOE. The purpose of this field trip is to introduce the present state of geologic and hydrologic knowledge concerning this site. This report describes the field trip. 108 refs., 6 figs., 1 tab

Limits on the thermal energy release from radioactive wastes in a mined geologic repository

International Nuclear Information System (INIS)

Scott, J.A.

1983-03-01

The theraml energy release of nuclear wastes is a major factor in the design of geologic repositories. Thermal limits need to be placed on various aspets of the geologic waste disposal system to avoid or retard the degradation of repository performance because of increased temperatures. The thermal limits in current use today are summarized in this report. These limits are placed in a hierarchial structure of thermal criteria consistent with the failure mechanism they are trying to prevent. The thermal criteria hierarchy is used to evaluate the thermal performance of a sample repository design. The design consists of disassembled BWR spent fuel, aged 10 years, close packed in a carbon steel canister with 15 cm of crushed salt backfill. The medium is bedded salt. The most-restrictive temperature for this design is the spent-fuel centerline temperature limit of 300 0 C. A sensitivity study on the effects of additional cooling prior to disposal on repository thermal limits and design is performed

Logistics Modeling of Emplacement Rate and Duration of Operations for Generic Geologic Repository Concepts

Energy Technology Data Exchange (ETDEWEB)

Kalinina, Elena Arkadievna; Hardin, Ernest

2015-11-01

This study identified potential geologic repository concepts for disposal of spent nuclear fuel (SNF) and (2) evaluated the achievable repository waste emplacement rate and the time required to complete the disposal for these concepts. Total repository capacity is assumed to be approximately 140,000 MT of spent fuel. The results of this study provide an important input for the rough-order-of-magnitude (ROM) disposal cost analysis. The disposal concepts cover three major categories of host geologic media: crystalline or hard rock, salt, and argillaceous rock. Four waste package sizes are considered: 4PWR/9BWR; 12PWR/21BWR; 21PWR/44BWR, and dual purpose canisters (DPCs). The DPC concepts assume that the existing canisters will be sealed into disposal overpacks for direct disposal. Each concept assumes one of the following emplacement power limits for either emplacement or repository closure: 1.7 kW; 2.2 kW; 5.5 kW; 10 kW; 11.5 kW, and 18 kW.

Logistics Modeling of Emplacement Rate and Duration of Operations for Generic Geologic Repository Concepts

International Nuclear Information System (INIS)

Kalinina, Elena Arkadievna; Hardin, Ernest

2015-01-01

This study identified potential geologic repository concepts for disposal of spent nuclear fuel (SNF) and (2) evaluated the achievable repository waste emplacement rate and the time required to complete the disposal for these concepts. Total repository capacity is assumed to be approximately 140,000 MT of spent fuel. The results of this study provide an important input for the rough-order-of-magnitude (ROM) disposal cost analysis. The disposal concepts cover three major categories of host geologic media: crystalline or hard rock, salt, and argillaceous rock. Four waste package sizes are considered: 4PWR/9BWR; 12PWR/21BWR; 21PWR/44BWR, and dual purpose canisters (DPCs). The DPC concepts assume that the existing canisters will be sealed into disposal overpacks for direct disposal. Each concept assumes one of the following emplacement power limits for either emplacement or repository closure: 1.7 kW; 2.2 kW; 5.5 kW; 10 kW; 11.5 kW, and 18 kW.

Draft Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

1999-01-01

The Proposed Action addressed in this EIS is to construct, operate and monitor, and eventually close a geologic repository at Yucca Mountain in southern Nevada for the disposal of spent nuclear fuel and high-level radioactive waste currently in storage at 72 commercial and 5 DOE sites across the United States. The EIS evaluates (1) projected impacts on the Yucca Mountain environment of the construction, operation and monitoring, and eventual closure of the geologic repository; (2) the potential long-term impacts of repository disposal of spent nuclear fuel and high-level radioactive waste; (3) the potential impacts of transporting these materials nationally and in the State of Nevada; and (4) the potential impacts of not proceeding with the Proposed Action

10 CFR 60.112 - Overall system performance objective for the geologic repository after permanent closure.

Science.gov (United States)

2010-01-01

... repository after permanent closure. 60.112 Section 60.112 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Technical Criteria Performance... environment following permanent closure conform to such generally applicable environmental standards for...

Office of Geologic Repositories issues hierarchy for a mined geologic disposal system

International Nuclear Information System (INIS)

1987-08-01

The Nuclear Regulatory Commission (NRC) has indicated that the identification of the issues that must be resolved to complete licensing assessments of site and design suitability is an important step in the licensing process. The issues hierarchy developed by the Office of Geologic Repositories (OGR) for the mined geologic disposal system (MGDS) are based on the issues-hierarchy concept presented in the Mission Plan. Specific questions are encompassed by the general issue statements in the OGR issues hierarchy. The OGR issues hierarchy is limited to the issues related to the siting and licensing requirements of applicable federal regulations and does not address the requirements of other regulations, functional or operating requirements for the MGDS, or requirements for the integration and the design/operational efficiency of the MGDS. 4 figs

Geotechnical support and topical studies for nuclear waste geologic repositories

International Nuclear Information System (INIS)

1989-01-01

The present report lists the technical reviews and comments made during the fiscal year 1988 and summarizes the technical progress of the topical studies. In the area of technical assistance, there were numerous activities detailed in the next section. These included 24 geotechnical support activities, including reviews of 6 Study Plans (SP) and participation in 6 SP Review Workshops, review of one whole document Site Characterization Plan (SCP) and participation in the Assembled Document SCP Review Workshops by 6 LBL reviewers; the hosting of a DOE program review, the rewriting of the project statement of work, 2 trips to technical and planning meetings; preparation of proposed work statements for two new topics for DOE, and 5 instances of technical assistance to DOE. These activities are described in a Table in the following section entitled ''Geoscience Technical Support for Nuclear Waste Geologic Repositories.''

On ocean island geological repository - a second-generation option for disposal of spent fuel and high-level waste

International Nuclear Information System (INIS)

Forsberg, C.W.

1993-01-01

The concept of an ocean subseabed geological high-level waste repository with access via an ocean island is discussed. The technical advantages include, in addition to geologic waste isolation, geographical isolation, near-zero groundwater flow through the disposal site, and near-infinite ocean dilution as a backup in the event of a failure of the repository geological waste isolation system. The institutional advantages may include reduced siting problems and the potential of creating an international waste repository. Establishment of a repository accepting wastes from many countries would allow cost sharing, aid international nonproliferation goals, and ensure proper disposal of spent fuel from developing countries. Major uncertainties that are identified in this concept are the uncertainties in rock conditions at waste disposal depths, costs, and ill-defined institutional issues

Geologic, stratigraphic, thermal, and mechanical factors which influence repository design in the bedded salt environment

International Nuclear Information System (INIS)

Ashby, J.P.; Nair, O.; Ortman, D.; Rowe, J.

1979-12-01

This report describes the geologic, stratigraphic, thermal, and mechanical considerations applicable to repository design. The topics discussed in the report include: tectonic activity; geologic structure; stratigraphy; rock mechanical properties; and hydrologic properties

Salt Repository Project waste emplacement mode decision paper: Revison 1

International Nuclear Information System (INIS)

1987-08-01

This paper provides a recommendation as to the mode of waste emplacement to be used as the current basis for site characterization activity for the Deaf Smith County, Texas, high level nuclear waste repository site. It also presents a plan for implementing the recommendation so as to provide a high level of confidence in the project's success. Since evaluations of high-level waste disposal in geologic repositories began in the 1950s, most studies emplacement in salt formations employed the vertical orientation for emplacing waste packages in boreholes in the floor of the underground facility. This orientation was used in trials at Project Salt Vault in the 1960s. The Waste Isolation Pilot Plant (WIPP) has recently settled on a combination of vertical and horizontal modes for various waste types. This paper analyzes the information available and develops a project position upon which to base current site characterization activities. The position recommended is that the SRP should continue to use the vertical waste emplacement mode as the reference design and to carry the horizontal mode as a ''passive'' alternative. This position was developed based upon the conclusions of a decision analysis, risk assessment, and cost/schedule impact assessment. 52 refs., 6 figs., 1 tab

Siting regions for deep geological repositories. Why just here?; Standortgebiete fuer geologische Tiefenlager. Warum gerade hier?

Energy Technology Data Exchange (ETDEWEB)

Rieser, A

2009-09-15

This report helps to the popularization of the Nagra works accomplished for the management and disposal of the radioactive wastes in Switzerland. The programme for management and disposal of the radioactive wastes are extensively determined by regulations. Protection of mankind and environment is the primary objective. The basic storage process is considered as having been solved. The question addressed in the report is where the facility has to be built; the site selection procedure includes five steps: 1) according to their type the wastes have to be allocated to two different repositories: for low- and intermediate-level wastes (L/ILW), and for high-level and alpha-toxic wastes (HLW); 2) the safety concept for both repositories and the requirements on the geology have to be determined; 3) large suitable geological-tectonic zones must be found where repositories could be built; 4) in these geological zones a suitable host rock has to be identified; 5) the most important spatial geological conditions of the host rock (minimum depth with respect to surface erosion, maximum depth in terms of engineering requirements, lateral extent) have to be identified. Based on these criteria, three suitable siting regions for a HLW repository were found in the North of Switzerland. The preferred host rock is Opalinus clay because of its very low permeability; it is therefore an excellent barrier against nuclide transport. In the three proposed siting regions, Opalinus clay is present in sufficient volumes at a suitable depth. For a L/ILW repository six different possible siting regions were identified, five in Northern Switzerland and one in Central Switzerland. In the three siting regions found for a possible HLW repository, it would also be possible to built a combined repository for both HLW and L/ILW wastes.

Important processes affecting the release and migration of radionuclides from a deep geological repository

International Nuclear Information System (INIS)

Barátová, Dana; Nečas, Vladimír

2017-01-01

The processes that affect significantly the transport of contaminants through the near field and far field of a deep geological repository of spent nuclear fuel were studied. The processes can be generally divided into (i) processes related to the release of radionuclides from the spent nuclear fuel; (ii) processes related to the radionuclide transport mechanisms (such as advection and diffusion); and (iii) processes affecting the rate of radionuclide migration through the multi-barrier repository system. A near-field and geosphere model of an unspecified geological repository sited in a crystalline rock is also described. Focus of the treatment is on the effects of the different processes on the activity flow of the major safety-relevant radionuclides. The activity flow was simulated for one spent fuel cask by using the GoldSim simulation tool. (orig.)

Geological mappability of bored versus drill and blast excavations for radioactive waste repositories

International Nuclear Information System (INIS)

Nilsen, B.; Ozdemir, L.

1992-01-01

The issue of accurate geological mappability has been subject of intense debate in the selection of bored versus drill and blast excavation for radioactive waste repositories. This paper is intended to provide an assessment of the problems usually encountered in mappability on the basis of field experience from a large number of completed tunnels, mainly as part of the Norwegian hydropower projects. The main conclusion is that mapping in a mechanically excavated underground opening, with very few exceptions, reflects the in-situ conditions more accurately than mapping in a drill and blast tunnel. This is due to the overbreak effects of drill and blast excavation, primarily

Planning geological underground repositories - Communicating with society

International Nuclear Information System (INIS)

Schenkel, W.; Gallego Carrera, D.; Renn, O.; Dreyer, M.

2009-06-01

The project 'Planning geological underground repositories: Communicating with society', financed by the Swiss Federal Office for Energy, aimed at identifying basic principles for an appropriate information and communication strategy in the process of finding an underground site to store radioactive wastes. The topic concerns an issue increasingly discussed in modern societies: How to improve the dialogue between science, infrastructure operators, public authorities, groups in civil society and the population to answer complex problems? Against this background, in the project the following questions were taken into account: (i) How can the dialogue between science, politics, economy, and the (non-)organised public be arranged appropriately? Which principles are to be considered in organising this process? How can distrust within the population be reduced and confidence in authorities and scientific expertise be increased? (ii) How can society be integrated in the process of decision-making so that this process is perceived as comprehensible, acceptable and legitimate? To answer these questions, an analysis method based on scientific theory and methodology was developed, which compares national participation and communication processes in finding underground storage sites in selected countries. Case studies have been carried out in Germany, Sweden, Belgium, and Switzerland. By using specific criteria to evaluate communication processes, the strong points as well as the drawbacks of the country-specific concepts of information, communication and participation have been analysed in a comparing dimension. By taking into account the outcomes, prototypical scenarios have been deduced that can serve as a basis for compiling a reference catalogue of measures, which is meant to support the Swiss communication strategy in the finding of an appropriate site for a nuclear waste repository. Following conclusions can be drawn from the international comparison: (i) Open and

The Poco de Caldas project: Natural analogues of processes in a radioactive waste repository

International Nuclear Information System (INIS)

Chapman, N.A.; McKinley, I.G.; Shea, M.E.; Smellie, J.A.T.

1993-01-01

The safe disposal of radioactive wastes by burial in deep geologic formations requires long-term predictions of the future behavior of the wastes nd their engineered repository. Such predictions can be tested by evaluating processes analogous to those which will occur in a repository, which have been long active in the natural geochemical environment. The title project is a comprehensive study of two ore deposits in Minas Gerais, Brasil, aimed at looking at uranium and thorium series radionuclide and rare earth element mobility, the development and movement of redox fronts, and the nature of natural groundwater colloids. A multidisciplinary team of experts from 27 laboratories carried out a fully integrated study of the geology, geomorphology, hydrogeology, geochemistry, hydrochemistry and geomicrobiology of the two sited for nearly four years. This book contains 20 papers covering the detailed findings, with particular emphasis on their significance for radioactive waste disposal, especially on the use of the data in testing models of radionuclide movement

Preclosure seismic design methodology for a geologic repository at Yucca Mountain. Topical report YMP/TR-003-NP

International Nuclear Information System (INIS)

1996-10-01

This topical report describes the methodology and criteria that the U.S. Department of Energy (DOE) proposes to use for preclosure seismic design of structures, systems, and components (SSCs) of the proposed geologic repository operations area that are important to safety. Title 10 of the Code of Federal Regulations, Part 60 (10 CFR 60), Disposal of High-Level Radioactive Wastes in Geologic Repositories, states that for a license to be issued for operation of a high-level waste repository, the U.S. Nuclear Regulatory Commission (NRC) must find that the facility will not constitute an unreasonable risk to the health and safety of the public. Section 60.131 (b)(1) requires that SSCs important to safety be designed so that natural phenomena and environmental conditions anticipated at the geologic repository operations area will not interfere with necessary safety functions. Among the natural phenomena specifically identified in the regulation as requiring safety consideration are the hazards of ground shaking and fault displacement due to earthquakes

Monitoring as component for the decision making in final repository projects; Monitoring als Baustein fuer die Entscheidungsfindung in Endlagerprojekten

Energy Technology Data Exchange (ETDEWEB)

Kallenbach-Herbert, Beate; Alt, Stefan [Oeko-Institut e.V., Darmstadt (Germany)

2012-12-15

The monitoring in final radioactive waste repositories is performed by continuous or repeated measurements of technical and geologic parameters during long time periods. The collected data serve manifold purposes. The central focus is to provide fundamental information for the decision between and within the three phases of a final repository project. This means that monitoring is not only the sum of technical surveillance measures. Monitoring is also important for several sociopolitical decisions, for instance in case of closure of the repository. The article discusses possible objectives and shows the relevant technical aspects that are used deduce the requirements for an integrated monitoring concept. It is shown that a monitoring concept should be developed early enough involving all groups that are concerned by the waste disposal project.

Canada's deep geological repository for used nuclear fuel - update on the site evaluation process and interweaving of aboriginal traditional knowledge

Energy Technology Data Exchange (ETDEWEB)

Watts, B.; Belfadhel, M.B.; Facella, J., E-mail: bwatt@nwmo.ca, E-mail: mbenbelfadhel@nwmo.ca, E-mail: jfacella@nwmo.ca [Nuclear Waste Management Organization, Toronto, ON (Canada)

2015-07-01

The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for the long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository (DGR) in a suitable crystalline or sedimentary rock formation. In May 2010, the NWMO initiated a nine-step site selection process to seek an informed and willing community to host Canada's deep geological repository. As of April 2015, twenty-two communities expressed interest in learning more about the project. This paper provides an update on the site evaluation process and describes the approach, methods and criteria used in the assessments, focusing on geological and community well-being studies. Engagement and field activities to interweave Aboriginal Traditional Knowledge with western science are also discussed. (author)

NAGRA - Sites for geological repositories - Geological surveys for stage 3

International Nuclear Information System (INIS)

2014-01-01

This brochure published by the Swiss National Cooperative for the Disposal of Radioactive Waste (NAGRA) examines the aims involved in the selection of sites for deep geological repositories for nuclear wastes in Switzerland. Various methods involved in their implementation are described. These include 3D-seismology, deep probe drillings, shallow drillings as well as field studies, gravimetric measurements and the study of the electrical properties of the ground and rock involved. These factors are discussed in detail. Maps are presented of the locations that are to be surveyed and details of the selected perimeters are shown. Also, the layout of a sample drilling site is presented. A timescale for the various surveys and work to be done is presented

A geologic scenario for catastrophic failure of the Yucca Mountain Nuclear Waste Repository, Nevada

International Nuclear Information System (INIS)

McMackin, M.R.

1993-01-01

A plausible combination of geologic factors leading to failure can be hypothesized for the Yucca Mountain Nuclear Waste Repository. The scenarios is constructed using elementary fault mechanics combined with geologic observations of exhumed faults and published information describing the repository site. The proposed repository site is located in the Basin and Range Province, a region of active crustal deformation demonstrated by widespread seismicity. The Yucca Mountain area has been characterized as tectonically quiet, which in the context of active crustal deformation may indicate the accumulation of the stresses approaching the levels required for fault slip, essentially stick-slip faulting. Simultaneously, dissolution of carbonate rocks in underlying karst aquifers is lowering the bulk strength of the rock that supports the repository site. Rising levels of hydrostatic stress concurrent with a climatically-driven rise in the water table could trigger faulting by decreasing the effective normal stress that currently retards fault slip. Water expelled from collapsing caverns in the underlying carbonate aquifer could migrate upward with sufficient pressure to open existing fractures or create new fractures by hydrofracturing. Water migrating through fractures could reach the repository in sufficient volume to react with heated rock and waste perhaps creating steam explosions that would further enhance fracture permeability. Closure of conduits in the underlying carbonate aquifer could lead to the elevation of the saturated zone above the level of the repository resulting in sustained saturation of radioactive waste in the repository and contamination of through-flowing groundwater

Salt Repository Project: FY 85 technical project plan

International Nuclear Information System (INIS)

1985-07-01

The FY 85 technical plan for the Salt Repository Project is briefly presented. The objectives of the project in relation to the Civilian Radioactive Waste Management Program are discussed, and the technical activities directed toward accomplishing these objectives are detailed. A budget is presented for each of the Level 2 work breakdown structure tasks (Systems, Waste Package, Site, Repository, Regulatory and Institutional, Exploratory Shaft, Test Facilities, Land Acquisition, and Project Management) in the various sections. An overall description, current status, and planned activities are presented for each of the subtasks which make up the above-mentioned Level 2 tasks. A strategy diagram and a master schedule are included and each of the milestones is also listed chronologically in the sections

Risk analysis for repositories in north Switzerland. Extent and probability of geologic processes and events

Energy Technology Data Exchange (ETDEWEB)

Buergisser, H M; Herrnberger, V

1981-07-01

The literature study assesses, in the form of expert analysis, geological processes and events for a 1200 km/sup 2/-area of northern Switzerland, with regard to repositories for medium- and high-active waste (depth 100 to 600 m and 600 to 2500 m, respectively) over the next 10/sup 6/ years. The area, which comprises parts of the Tabular Jura, the folded Jura and the Molasse Basin, the latter two being parts of the Alpine Orogene, has undergone a non-uniform geologic development since the Oligocene. Within the next 10/sup 4/ to 10/sup 5/ years a maximum earthquake intensity of VIII-IX (MSK-scale) has been predicted. After this period, particularly in the southern and eastern parts of the area, glaciations will probably occur, with asociated erosion of possibly 200 to 300 m. Fluvial erosion as a response to an uplift could reach similar values after 10/sup 5/ to 10/sup 6/ years; however, there are no data on the recent relative vertical crustal movements of the area. The risk of a meteorite impact is considered small as compared to that of these factors. Seismic activity and the position and extent of faults are so poorly known within the area that the faulting probability cannot be derived at present. Flooding by the sea, intrusion of magma, diapirism, metamorphism and volcanic eruptions are not considered to be risk factors for final repositories in northern Switzerland. For the shallow-type repositories, the risk of denudation and landslides have to be judged when locality-bound projects have been proposed.

Analysis of spent fuel performance in a geologic repository

International Nuclear Information System (INIS)

Apted, M.J.; Liebetrau, A.M.; Engel, D.W.; Alexander, D.H.

1986-04-01

The Analytical REpository Source-Term (AREST) code developed for the US Department of Energy is being used to assess the time-dependent release rate of radionuclides from spent nuclear fuel disposed in geologic repositories. The Waste Package Release (WPR) submodule of AREST calculates the release from individual waste packages containing spent fuel based on site-specific design, solubility, corrosion, sorption, and mass transfer data. Under the open system conditions of a repository, there are two limiting release mechanisms: surface reaction control and transport control. In addition, a separate release case is defined for soluble radionuclides that are inventory limited. Mass transfer equations for each of these processes are incorporated into AREST. Four separate sources are identified in the AREST code based on inventory and release mechanism: UO 2 matrix (transport limited), gap (inventory limited), grain boundary (inventory limited, combined with gap), and cladding (transport limited). The calculated release of nuclides contained in the matrix (> 90% of the entire inventory) is controlled by UO 2 solubility or the solubility of a nuclide-bearing phase, whichever is lower

United States Crystalline Repository Project - key research areas

International Nuclear Information System (INIS)

Patera, E.S.

1986-01-01

The Crystalline Repository Project is responsible for siting the second high-level nuclear waste repository in crystalline rock for the US Department of Energy. A methodology is being developed to define data and information needs and a way to evaluate that information. The areas of research the Crystalline Repository Project is involved in include fluid flow in a fractured network, coupled thermal, chemical and flow processes and cooperation in other nations and OECD research programs

Characterization of Swelling Clays as Components of the Engineered Barrier System for Geological Repositories. Results of an IAEA Coordinated Research Project 2002-2007

International Nuclear Information System (INIS)

2013-11-01

At the request of the Member States, the IAEA coordinates research into subjects of common interest in the context of the peaceful application of nuclear technology. The coordinated research projects (CRPs) are intended to promote knowledge and technology transfer between Member States and are largely focused on subjects of prime interest to the international nuclear community. This report presents the results of a CRP carried out between 2002 and 2007 on the subject of swelling clays proposed for use as a component in the engineered barrier system (EBS) of the multibarrier concept for disposal of radioactive waste. In 2002, under the auspices of the IAEA, a number of Member States came together to form a Network of Centres of Excellence on Training in and Demonstration of Waste Disposal Technologies in Underground Research Facilities (URF Network). This network identified the general subject of the application of high swelling clays to seal repositories for radioactive waste, with specific emphasis on the isolation of high level radioactive waste from the biosphere, as being suitable for a CRP. Existing concepts for geological repositories for high level radioactive waste and spent nuclear fuel require the use of EBSs to ensure effective isolation of the radioactive waste. There are two major materials proposed for use in the EBS, swelling clay based materials and cementitious/concrete materials. These materials will be placed between the perimeter of the excavation and the waste container to fill the existing gap and ensure isolation of the waste within the canister (also referred to as a container in some EBS concepts) by supporting safety through retardation and confinement. Cementitious materials are industrially manufactured to consistent standards and are readily available in most locations and therefore their evaluation is of less value to Member States than that of swelling clays. There exists a considerable range of programme development regarding

Impact of advanced fuel cycles on uncertainty associated with geologic repositories

International Nuclear Information System (INIS)

Rechard, Rob P.; Lee, Joon; Sutton, Mark; Greenberg, Harris R.; Robinson, Bruce A.; Nutt, W. Mark

2013-01-01

This paper provides a qualitative evaluation of the impact of advanced fuel cycles, particularly partition and transmutation of actinides, on the uncertainty associated with geologic disposal. Based on the discussion, advanced fuel cycles, will not materially alter (1) the repository performance (2) the spread in dose results around the mean (3) the modeling effort to include significant features, events, and processes in the performance assessment, or (4) the characterization of uncertainty associated with a geologic disposal system in the regulatory environment of the United States. (authors)

Geotechnical support and topical studies for nuclear waste geologic repositories: Annual report, Fiscal Year 1986

International Nuclear Information System (INIS)

1986-11-01

The multidisciplinary project was initiated in fiscal year 1986. It comprises two major interrelated parts: (1) Technical Assistance. This part of the project includes: (a) review of the progress of major projects in the DOE Office of Civilian Radioactive Waste Management Program and advise the Engineering and Geotechnology Division on significant technical issues facing each project; (b) analyze geotechnical data, reports, tests, surveys and plans for the different projects; (c) review and comment on major technical reports and other program documents such as site characterization plans and area characterization plans and (d) provide scientific and technical input at technical meetings. (2) Topical Studies. This activity comprises studies on scientific and technical topics, and issues of significance to in-situ testing, test analysis methods, and performance assessment of nuclear waste geologic repositories. The subjects of study were selected based on discussions with DOE staff. For fiscal year 1986, one minor and one major area of investigation were undertaken. The minor topic is a preliminary consideration and planning exercise for post-closure monitoring studies. The major topic, with subtasks involving various geoscience disciplines, is on the mechanical, hydraulic, geophysical and geochemical properties of fractures in geologic rock masses. The present report lists the technical reviews and comments made during the fiscal year and summarizes the technical progress of the topical studies

The Cigeo project, Meuse/Haute-Marne reversible geological disposal facility for radioactive waste. Project Owner File, Public debate of 15 May to 15 October 2013

International Nuclear Information System (INIS)

Dupuis, Marie-Claude; Gonnot, Francois-Michel

2013-07-01

Andra is exploring several options for the disposal of low-level long-lived waste (LLW-LL). With the French Government's approval, in June 2008 Andra began looking around France for a site to build an LLW-LL repository. In late 2008 it provided the Government with a report analysing the geological, environmental and socio-economic aspects of the forty odd municipalities that expressed an interest in the project. After the withdrawal of the two municipalities chosen in 2009 to conduct geological investigations, the government asked Andra to re-explore the various management options for graphite and radium-bearing waste, focusing in particular on ways to manage these types of waste separately. The High Committee for Transparency and Information on Nuclear Safety (HCTISN) created a working group to provide feedback on the search for a site for LLW-LL. Andra submitted a report to the Government in late 2012. This report contains proposals for continuing the search and draw in particular on the HCTISN's recommendations. Contents: 1 - Radioactive waste (Sources, Types, Management, Waste to be disposed of at Cigeo, Cigeo's estimated disposal capacities, Where IS HLW and ILW-LL being stored until Cigeo is commissioned? 2 - Why deep geological disposal? (A 15-year research programme, Presentation and assessment of the research results, The public debate of 2005-2006, Deep geological disposal ratified by the 2006 Planning Act, The 2006 Planning Act: other areas of research complementary to deep geological disposal, The situation in other countries); 3 - Why the Meuse/Haute-Marne site? (Selection of the Meuse and Haute-Marne site to host an underground research laboratory, The geological formation in the Meuse and Haute-Marne site, Callovo-Oxfordian clay, Siting of Cigeo's installations); 4 - How will Cigeo operate? (The installations at Cigeo, Construction of Cigeo, Transport of waste packages, Operation of Cigeo, Closure of Cigeo); 5 - Safety at Cigeo

Swiss plans for deep geological repositories for radioactive wastes - Basics for communication at the localities affected

International Nuclear Information System (INIS)

Gallego Carrera, D.; Renn, O.; Dreyer, M.

2009-06-01

This report for the Swiss Federal Office of Energy (SFOE) discusses the concept of how information concerning deep geological repositories for radioactive wastes should be presented and communicated to those in the areas which have been designated as potential sites for the repositories. Communication basics based on scientific knowledge in this area are discussed. The importance of a concept for general communication and risk-communication as a particular challenge are discussed. Trust and transparency are quoted as being indispensable in this connection. Ways of dealing with various target audiences and the media are examined. The report is concluded with a check-list that deals with important questions arising from the process of communicating information on deep geological repositories for radioactive wastes

Deep geological disposal research in Argentina

International Nuclear Information System (INIS)

Ninci Martinez, Carlos A.; Ferreyra, Raul E.; Vullien, Alicia R.; Elena, Oscar; Lopez, Luis E.; Maloberti, Alejandro; Nievas, Humberto O.; Reyes, Nancy C.; Zarco, Juan J.; Bevilacqua, Arturo M.; Maset, Elvira R.; Jolivet, Luis A.

2001-01-01

Argentina shall require a deep geological repository for the final disposal of radioactive wastes, mainly high-level waste (HLW) and spent nuclear fuel produced at two nuclear power plants and two research reactors. In the period 1980-1990 the first part of feasibility studies and a basic engineering project for a radioactive high level waste repository were performed. From the geological point of view it was based on the study of granitic rocks. The area of Sierra del Medio, Province of Chubut, was selected to carry out detailed geological, geophysical and hydrogeological studies. Nevertheless, by the end of the eighties the project was socially rejected and CNEA decided to stop it at the beginning of the nineties. That decision was strongly linked with the little attention paid to social communication issues. Government authorities were under a strong pressure from social groups which demanded the interruption of the project, due to lack of information and the fear it generated. The lesson learned was: social communication activities shall be carried out very carefully in order to advance in the final disposal of HLW at deep geological repositories (author)

Considerations on pressure build-up in deep geological repositories for radioactive waste

International Nuclear Information System (INIS)

Beer, Hans-Frieder

2015-01-01

Gas formation caused by corrosion of metals is a pivotal point with respect to the safety analysis of deep geological repositories. Solid corrosion products are formed unavoidably during the gas formation. The volumes of these solid corrosion products are multiples of the original waste volume. These solid corrosion products are chemically extremely stable and result in a pressure increase inside the repository. This pressure is considerably higher than that of the overlaying rock. The question that arises is, why this aspect is not considered in the consulted documents.

The Use of Numerical Models in Support of Site Characterization and Performance Assessment Studies of Geological Repositories. Results of an IAEA Coordinated Research Project 2005-2010

International Nuclear Information System (INIS)

2013-10-01

The siting, development and operation of waste disposal facilities, and the related safety issues, have been described in many IAEA publications. The safe management and disposal of radioactive waste from the nuclear fuel cycle remains a necessary condition for future development of nuclear energy. In particular, the disposal of high level waste and spent nuclear fuel in geological repositories, despite having been studied worldwide over the past several decades, still requires full scale demonstration through safe implementation, as planned at the national level in Finland and Sweden by 2020 and 2023, respectively, and in France by 2025. Safety assessment techniques are currently applicable to potential facility location and development through a quite large range of approaches and methodologies. By implementing research activities through coordinated research projects (CRPs), the IAEA enables research institutes in both developing and developed Member States to collaborate on research topics of common interest. In response to requests by several Member States in different networks and platforms dealing with waste disposal, in 2005 a CRP on The Use of Numerical Models in Support of Site Characterization and Performance Assessment Studies of Geological Repositories was proposed and developed to transfer modelling expertise and numerical simulation technology to countries needing them for their national nuclear waste management programmes. All Member States involved in this CRP have acquired the scientific basis for, and expertise in, the site characterization process, including test design, data analysis, model calibration, model validation, predictive modelling, sensitivity analysis and uncertainty propagation analysis. This expertise is documented in this publication, in which numerical modelling is used to address the pertinent issue of site characterization and its impact on safety, using data and information from a potential repository site

On risk analysis for repositories in northern Switzerland: extent and probability of geological processes and events

International Nuclear Information System (INIS)

Buergisser, H.M.; Herrnberger, V.

1981-01-01

The literature study assesses, in the form of expert analysis, geological processes and events for a 1200 km 2 -area of northern Switzerland, with regard to repositories for medium- and high-active waste (depth 100 to 600 m and 600 to 2500 m, respectively) over the next 10 6 years. The area, which comprises parts of the Tabular Jura, the folded Jura and the Molasse Basin, the latter two being parts of the Alpine Orogene, has undergone a non-uniform geologic development since the Oligocene. Within the next 10 4 to 10 5 years a maximum earthquake intensity of VIII-IX (MSK-scale) has been predicted. After this period, particularly in the southern and eastern parts of the area, glaciations will probably occur, with associated erosion of possibly 200 to 300 m. Fluvial erosion as a reponse to an uplift could reach similar values after 10 5 to 10 6 years; however, there are no data on the recent relative vertical crustal movements of the area. The risk of a meteorite impact is considered small as compared to that of these factors. Seismic activity and the position and extent of faults are so poorly known within the area that the faulting probability cannot be derived at present. Flooding by the sea, intrusion of magma, diapirism, metamorphism and volcanic eruptions are not considered to be risk factors for final repositories in northern Switzerland. For the shallow-type repositories, the risk of denudation and landslides have to be judged when locality-bound projects have been proposed. (Auth.)

Engineering feasibility for the fabrication and emplacement of cementitious repository materials: results from the EC-ESDRED project

International Nuclear Information System (INIS)

Alonso, Maria Cruz; Garcia-Sineriz, Jose Luis

2012-01-01

Maria Cruz Alonso of the Spanish National Research Council gave a presentation that summarised relevant findings on cementitious materials from the EC ESDRED (Engineering Studies and Demonstration of Repository Designs) Project. Concrete will be used for different purposes during the construction of geologic repositories for radioactive waste. These purposes include grouting, tunnel and drift lining, and tunnel plugging and sealing. Although some of the concrete may be removed before repository closure, a significant amount of concrete will remain in the repository. An important concern regarding the use of cementitious materials in geologic repositories for HLW and spent fuel is their interaction with the bentonite buffer, backfill material, and the host rock close to the repository near-field. For this reason, the ESDRED project has developed a low-pH concrete formulation as an alternative to standard ordinary Portland cement (OPC) concrete formulations with the aim of reducing the interaction of the cementitious materials with the near-field components. The main functional requirement required in the development of the low-pH material was a pore fluid pH < 11, which is considered acceptable for preventing or reducing the alteration of the bentonite EBS. Other functional requirements considered in the development of the low-pH concrete were: - Hydraulic conductivity. - Mechanical properties. - Durability. - Workability and pumpability. - Slumping. - Peak hydration temperature. - Thermal conductivity. - Use of organic components. - Use of other products. The development of the low-pH concrete involved laboratory work, as well as field testing at the Aespoe underground research laboratory (URL) in Sweden, and in the Grimsel URL and at the Hagerbach site in Switzerland. The ESDRED project demonstrated that low-pH cements can be formulated and used for production of concrete plugs and rock support. OPC can be used as the cement included in low-pH blends, but at least

Hydrogen transfer experiments and modelization in clay rocks for radioactive waste deep geological repository

International Nuclear Information System (INIS)

Boulin, P.

2008-10-01

Gases will be generated by corrosion of high radioactive waste containers in deep geological repositories. A gas phase will be generated. Gas pressure will build up and penetrated the geological formation. If gases do not penetrate the geological barrier efficiently, the pressure build up may create a risk of fracturing and of creation of preferential pathways for radionuclide migration. The present work focuses on Callovo-Oxfordian argillites characterisation. An experiment, designed to measure very low permeabilities, was used with hydrogen/helium and analysed using the Dusty Gas Model. Argillites close to saturation have an accessible porosity to gas transfer that is lower than 0,1% to 1% of the porosity. Analysis of the Knudsen effect suggests that this accessible network should be made of 50 nm to 200 nm diameter pores. The permeabilities values were integrated to an ANDRA operating model. The model showed that the maximum pressure expected near the repository would be 83 bar. (author)

Site descriptive modelling during characterization for a geological repository for nuclear waste in Sweden

International Nuclear Information System (INIS)

Stroem, A.; Andersson, J.; Skagius, K.; Winberg, A.

2008-01-01

The Swedish programme for geological disposal of spent nuclear fuel is approaching major milestones in the form of permit applications for an encapsulation plant and a deep geologic repository. This paper presents an overview of the bedrock and surface modelling work that comprises a major part of the on-going site characterization in Sweden and that results in syntheses of the sites, called site descriptions. The site description incorporates descriptive models of the site and its regional setting, including the current state of the geosphere and the biosphere as well as natural processes affecting long-term evolution. The site description is intended to serve the needs of both repository engineering with respect to layout and construction, and safety assessment, with respect to long-term performance. The development of site-descriptive models involves a multi-disciplinary interpretation of geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry, transport properties and ecosystems using input in the form of available data for the surface and from deep boreholes

Salt Repository Project. FY-84 technical project plan

International Nuclear Information System (INIS)

1984-08-01

The FY 84 technical plans for the Salt Repository Project (SRP) are briefly presented. The objectives of the project in relation to the Civilian Radioactive Waste Management (CRWM) program are discused and the technical activities directed toward accomplishing these objectives are detailed. A budget is presented for each of the Level 2 Work Breakdown Structure Tasks (Systems, Waste Package, Site, Repository, Regulatory and Institutional, Test Facilities, Exploratory Shaft, Land Acquisition, and Program Management) in an appendix. An overall description, current status, and planned activities are presented for each of the subtasks which make up the above-mentioned Level 2 tasks. Milestones and their definitions for the plan year, as well as milestones for the outyears are also presented at this same subtask level for each subtask

Reference Design Description for a Geologic Repository

International Nuclear Information System (INIS)

2000-01-01

One of the current major national environmental problems is the safe disposal of large quantities of spent nuclear fuel and high-level radioactive waste materials, which are rapidly accumulating throughout the country. These radioactive byproducts are generated as the result of national defense activities and from the generation of electricity by commercial nuclear power plants. At present, spent nuclear fuel is accumulating at over 70 power plant sites distributed throughout 33 states. The safe disposal of these high-level radioactive materials at a central disposal facility is a high national priority. This Reference Design Description explains the current design for a potential geologic repository that may be located at Yucca Mountain in Nevada for the disposal of spent nuclear fuel and high-level radioactive waste materials. This document describes a possible design for the three fundamental parts of a repository: a surface facility, subsurface repository, and waste packaging. It also presents the current conceptual design of the key engineering systems for the final four phases of repository processes: operations, monitoring, closure, and postclosure. In accordance with current law, this design does not include an interim storage option. In addition, this Reference Design Description reviews the expected long-term performance of the potential repository. It describes the natural barrier system which, together with the engineered systems, achieves the repository objectives. This design will protect the public and the environment by allowing the safe disposal of radioactive waste received from government-owned custodial spent fuel sites, high-level radioactive waste sites, and commercial power reactor sites. All design elements meet or exceed applicable regulations governing the disposal of high-level radioactive waste. The design will provide safe disposal of waste materials for at least a 10,000 year period. During this time interval, natural radioactive decay

Mathematical modelling of heat production in deep geological repository of high-level nuclear waste

International Nuclear Information System (INIS)

Kovanda, O.

2017-01-01

Waste produced by nuclear industry requires special handling. Currently, there is a research taking place, focused at possibilities of nuclear waste storage in deep geological repositories, hosted in stable geological environment. The high-level nuclear waste produces significant amount of heat for a long time, which can affect either environment outside of or within the repository in a negative way. Therefore to reduce risks, it is desirable to know the principles of such heat production, which can be achieved using mathematical modeling. This thesis comes up with a general model of heat production-time dependency, dependable on initial composition of the waste. To be able to model real situations, output of this thesis needs to be utilized in an IT solution. (authors)

Parameters and criteria influencing the selection of waste emplacement configurations in mined geologic repositories

International Nuclear Information System (INIS)

Bechthold, W.; Closs, K.D.; Papp, R.

1988-01-01

Reference concepts for repositories in deep geological formations have been developed in several countries. For these concepts, emplacement configurations vary within a wide range that comprises drift emplacement of unshielded or self-shielded packages and horizontal or vertical borehole emplacement. This is caused by different parameters, criteria, and criteria weighting factors. Examples for parameters are the country's nuclear power program and waste management policy, its geological situation, and safety requirements, examples for criteria and repository area requirements, expenditures of mining and drilling, and efforts for emplacement and, if required, retrieval. Due to the variety of these factors and their ranking in different countries, requirements for a safe, dependable and cost-effective disposal of radioactive waste can be met in various ways

Siting of repositories for high level nuclear waste geological and institutional issues

International Nuclear Information System (INIS)

Ahagen, H.

1993-01-01

Two studies have been conducted in Sweden under contract from SKN-National Board for Spent Nuclear Fuel. The responsibilities of SKN has been transferred to SKI as of July 1, 1992. The first study is related to a compilation of experience and lessons learned from siting of nuclear waste repositories and other controversial facilities in seven countries. The second study is aimed at compiling examples of the state of knowledge related to the regional geological information with relevance to siting of a repository in Sweden. This paper is drawing the general combined conclusions from both these studies. The first study reviewed programs for siting of nuclear and hazardous waste disposal facilities in Canada, Finland, France, Sweden, Switzerland, United Kingdom and USA. The main topics reviewed are related to a/ The use of technical screening, b/ Legal framework and local veto, c/ Public involvement, d/ Interim storage and schedule flexibility, e/ Sequential vs. parallel characterization. The second study focused on the regional geological information available for Sweden and if this information allows for a ''grouping'' of tectonic regions in Sweden with significant differences in history and characteristics. Factors studied as potentially important for siting are bedrock properties, mineralizations, ground water conditions and available volume for a repository. The experience gained from these studies is aimed to be used as background information in the review of the program conducted for the Swedish nuclear utilities by SKB. SKB will according to current plans initiate siting for a repository for spent nuclear fuel in Sweden during 1993. (author). 2 refs

Surface facilities for geological deep repositories - Measures against dangers during construction and operation

International Nuclear Information System (INIS)

2013-09-01

This brochure published by the Swiss National Cooperative for the Disposal of Radioactive Waste (NAGRA) discusses the measures that are to be taken to address the dangers encountered during the construction and operation of deep geological repositories for nuclear wastes. Firstly, the operation of such repositories during the emplacement of nuclear wastes is discussed and examples of possible repositories for fuel rods and highly-radioactive waste are presented. Various emission-protection issues and safety measures to be taken during construction of such repositories are looked at as is the protection of ground water. Safety considerations during the operational phase are discussed, including inclusion methods used for the wastes and radiation protection. The handling of radioactive wastes, the recognition of dangers and measures to be taken to counteract them are discussed. Various possible accidents are looked at

Microbial Influence on the Performance of Subsurface, Salt-Based Radioactive Waste Repositories. An Evaluation Based on Microbial Ecology, Bioenergetics and Projected Repository Conditions

International Nuclear Information System (INIS)

Swanson, J.S.; Reed, D.T.; Cherkouk, A.; Arnold, T.; Meleshyn, A.; Patterson, Russ

2018-01-01

For the past several decades, the Nuclear Energy Agency Salt Club has been supporting and overseeing the characterisation of rock salt as a potential host rock for deep geological repositories. This extensive evaluation of deep geological settings is aimed at determining - through a multidisciplinary approach - whether specific sites are suitable for radioactive waste disposal. Studying the microbiology of granite, basalt, tuff, and clay formations in both Europe and the United States has been an important part of this investigation, and much has been learnt about the potential influence of microorganisms on repository performance, as well as about deep subsurface microbiology in general. Some uncertainty remains, however, around the effects of microorganisms on salt-based repository performance. Using available information on the microbial ecology of hyper-saline environments, the bioenergetics of survival under high ionic strength conditions and studies related to repository microbiology, this report summarises the potential role of microorganisms in salt-based radioactive waste repositories

Modelling of radionuclide transport along the underground access structures of deep geological repositories

Energy Technology Data Exchange (ETDEWEB)

Poller, A. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Smith, P. [SAM Switzerland GmbH, Zuerich (Switzerland); Mayer, G.; Hayek, M. [AF-Consult Switzerland AG, Baden (Switzerland)

2014-08-15

The arrangement and sealing of the access routes to a deep geological repository for radioactive waste should ensure that any radionuclide release from the emplacement rooms during the post closure phase does not by-pass the geological barriers of the repository system to a significant extent. The base case of the present study, where realistic values for the hydraulic properties of the seals and the associated excavation damage zones were assumed, assesses to what extent this is actually the case for different layout variants (ramp and shaft access and shaft access only). Furthermore, as a test of robustness of system performance against uncertainties related to such seals and the associated excavation damage zones, the present study also considers a broad spectrum of calculation cases including the hypothetical possibility that the seals perform much more poorly than expected and to check whether, consequently, the repository tunnel system and the access structures may provide significant release pathways. The study considers a generic repository system for high-level waste (HLW repository) and for low- and intermediate-level waste (L/ILW repository), both with Opalinus Clay as the host rock. It also considers the alternative possibilities of a ramp or a shaft as the access route for material transport (waste packages, etc.) to the underground facilities. Additional shafts, e.g. for the transport of persons and for ventilation, are included in both cases. The overall modelling approach consists of three broad steps: (a) the network of tunnels and access structures is implemented in a flow model, which serves to calculate water flow rates along the tunnels and through the host rock; (b) all relevant transport paths are implemented in a radionuclide release and transport model, the water flow rates being obtained from the preceding flow model calculations; (c) individual effective dose rates arising from the radionuclides released from the considered repository

An analysis of repository waste-handling operations

International Nuclear Information System (INIS)

Dennis, A.W.

1990-09-01

This report has been prepared to document the operational analysis of waste-handling facilities at a geologic repository for high-level nuclear waste. The site currently under investigation for the geologic repository is located at Yucca Mountain, Nye County, Nevada. The repository waste-handling operations have been identified and analyzed for the year 2011, a steady-state year during which the repository receives spent nuclear fuel containing the equivalent of 3000 metric tons of uranium (MTU) and defense high-level waste containing the equivalent of 400 MTU. As a result of this analysis, it has been determined that the waste-handling facilities are adequate to receive, prepare, store, and emplace the projected quantity of waste on an annual basis. In addition, several areas have been identified where additional work is required. The recommendations for future work have been divided into three categories: items that affect the total waste management system, operations within the repository boundary, and the methodology used to perform operational analyses for repository designs. 7 refs., 48 figs., 11 tabs

A Rock Mechanics and Coupled Hydro mechanical Analysis of Geological Repository of High Level Nuclear Waste in Fractured Rocks

International Nuclear Information System (INIS)

Min, Kibok

2011-01-01

This paper introduces a few case studies on fractured hard rock based on geological data from Sweden, Korea is one of a few countries where crystalline rock is the most promising rock formation as a candidate site of geological repository of high level nuclear waste. Despite the progress made in the area of rock mechanics and coupled hydro mechanics, extensive site specific study on multiple candidate sites is essential in order to choose the optimal site. For many countries concerned about the safe isolation of nuclear wastes from the biosphere, disposal in a deep geological formation is considered an attractive option. In geological repository, thermal loading continuously disturbs the repository system in addition to disturbances a recent development in rock mechanics and coupled hydro mechanical study using DFN(Discrete Fracture Network) - DEM(Discrete Element Method) approach mainly applied in hard, crystalline rock containing numerous fracture which are main sources of deformation and groundwater flow

Process for selecting a site for Canada's deep geological repository for used nuclear fuel

International Nuclear Information System (INIS)

Facella, J.; Ben Belfadhel, M.; Patton, P.

2012-01-01

'Full Text:' The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management, the approach selected by the Government of Canada for long-term management of used nuclear fuel waste generated by Canadian nuclear reactors. The ultimate objective of Adaptive Phased Management is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable crystalline or sedimentary rock formation at a depth of about 500m. The repository will consist of a series of access and service shafts and a series of tunnels leading to placement rooms where used fuel will be placed and sealed in competent rock using a multi-barrier system which includes long lived specially designed containers, sealing materials such as bentonite and the rock itself. The used fuel will be monitored throughout all phases of implementation and will also remain retrievable for an extended period of time. In May 2010, the NWMO published the site selection process that serves as the road map to decision-making on the location for the deep geological repository. NWMO initiated the process with a first stage that invites communities to learn more about the project and the site selection process. NWMO is actively building awareness of the project and, on request of communities, is delivering briefings, supporting community capacity building and undertaking screenings of site suitability. This panel presentation provides a brief description of: Adaptive Phased Management including the deep geological repository which is its ultimate goal, and the design of the site selection process, and importantly the approach to assessing the suitability of sites from both a social and technical perspective. The panel presentation will be conducted in three parts: site selection process and engagement, Aboriginal engagement and Technical evaluations, followed by a discussion. The presentation will outline how NWMO sought

The Sellafield repository project information programme

Energy Technology Data Exchange (ETDEWEB)

Curd, P J [United Kingdom Nirex Limited (United Kingdom)

1993-07-01

The Sellafield Repository Project Information programme has been guided by formal research and by feedback through members of the team. Progress has been made and a significant majority of local people support the project and feel it will benefit the area. (author)

The Sellafield repository project information programme

International Nuclear Information System (INIS)

Curd, P.J.

1993-01-01

The Sellafield Repository Project Information programme has been guided by formal research and by feedback through members of the team. Progress has been made and a significant majority of local people support the project and feel it will benefit the area. (author)

Effect of reprocessing and recycling on the geologic repository dose rate : status

International Nuclear Information System (INIS)

Morris, E. E.; Nutt, W. M.; Wigeland, R. A.; Nuclear Engineering Division

2007-01-01

Two simplified repository performance assessment models are used to assess the impact of modeling changes in on conclusions regarding the impact of various reprocessing and recycling strategies. Waste streams from a pressurized water reactor (PWR) and a preliminary design for an advanced burner test reactor (ABTR) are used for this study of the effects on the estimated dose rate resulting from the release of radionuclides from a geologic repository. Calculations for the PWR make use of radionuclide discharge vectors for an assumed burnup of 51 GWd/MTIHM[1]. The repository is assumed to be filled with 70,000 MT of the spent fuel or with a glass waste form containing the radionuclides from 70,000 MT of spent PWR fuel. For the ABTR, the radionuclide inventory discharged at the end of an equilibrium cycle[2] is processed into a glass waste form for repository disposal, assuming actinide recovery efficiencies ranging from 90% to 99.99%. The recovered actinides are returned to the reactor. To compare with the PWR results, the repository is assumed to be filled with ABTR waste from fuel that has generated the same amount of thermal energy as 70,000 MT of the PWR fuel. The two repository performance assessment models, the first a simplified model[3] (SSR) based on the site recommendation model used by the Yucca Mountain Project (YMP)[4], and the second an updated simplified model (US) based on more recent modeling developments by the YMP are implemented in the computer simulation code GoldSim[5]. The updated model is based on a simplified model used to conduct a sensitivity analysis to evaluate factors that potentially influence performance of a repository at Yucca Mountain over the period of peak dose[6]. Factors that have either a minor or no effect on the peak dose either were not included in that simplified model or were included in a bounding representation. In the US model, enhancements were made to include some factors that have an effect on the dose occurring

MONITORED GEOLOGIC REPOSITORY LIFE CYCLE COST ESTIMATE ASSUMPTIONS DOCUMENT

International Nuclear Information System (INIS)

R.E. Sweeney

2001-01-01

The purpose of this assumptions document is to provide general scope, strategy, technical basis, schedule and cost assumptions for the Monitored Geologic Repository (MGR) life cycle cost (LCC) estimate and schedule update incorporating information from the Viability Assessment (VA) , License Application Design Selection (LADS), 1999 Update to the Total System Life Cycle Cost (TSLCC) estimate and from other related and updated information. This document is intended to generally follow the assumptions outlined in the previous MGR cost estimates and as further prescribed by DOE guidance

Monitored Geologic Repository Life Cycle Cost Estimate Assumptions Document

International Nuclear Information System (INIS)

Sweeney, R.

2000-01-01

The purpose of this assumptions document is to provide general scope, strategy, technical basis, schedule and cost assumptions for the Monitored Geologic Repository (MGR) life cycle cost estimate and schedule update incorporating information from the Viability Assessment (VA), License Application Design Selection (LADS), 1999 Update to the Total System Life Cycle Cost (TSLCC) estimate and from other related and updated information. This document is intended to generally follow the assumptions outlined in the previous MGR cost estimates and as further prescribed by DOE guidance

Life cycle assessment of geological repositories for the final disposal of spent fuel in Finland and Sweden

International Nuclear Information System (INIS)

Puhrer, A.; Bauer, C.

2014-01-01

This paper presents a Life Cycle Assessment (LCA) of the geological repositories for the final disposal of spent nuclear fuel in Finland and Sweden. A separate LCA has been performed for the geological spent fuel repository in each country and the results have been compared. A further benchmark comparison has been made with the LCA of the Swiss geological repository for high-level waste and spent fuel. The life cycle inventory (LCI) product system boundaries include the spent fuel repository and encapsulation facility in each country. All materials, processes, consumed utilities and transport associated with the construction, operation and closure of the repositories for spent fuel are included in the LCI. The life cycle impact assessment (LCIA) is performed using two methods: IPCC 2007 Climate Change and ReCiPe. These assessment methods return results pertaining to global warming potential (GWP) as well as a number of environmental impact categories such as human toxicity and natural land transformation. Results indicate that the use of copper for disposal canister fabrication and bentonite for repository backfilling are the causes for most of the environmental impact of the spent fuel repositories in Finland and Sweden. Alternate, less bentonite-intensive backfilling scenarios may mitigate this impact. While the Swiss bentonite consumption is lower and no copper is used for canister fabrication, the Swiss electricity and fuel consumption associated with final disposal of high-level waste and spent fuel is significantly higher than in Finland or Sweden. Approximately 1 g CO 2 -eq is emitted due to the final disposal of spent fuel and HLW per kWh of nuclear generated electricity. This represents some 10% of the emissions due to the entire nuclear energy chain and is practically negligible in the context of GHG emissions of other energy technologies. (authors)

10 CFR 63.113 - Performance objectives for the geologic repository after permanent closure.

Science.gov (United States)

2010-01-01

... closure. (a) The geologic repository must include multiple barriers, consisting of both natural barriers... in combination with natural barriers, radiological exposures to the reasonably maximally exposed... engineered barrier system must be designed so that, working in combination with natural barriers, releases of...

Performance analysis for waste repositories in the nordic countries. Report for project AFA-1.2

Energy Technology Data Exchange (ETDEWEB)

Vuori, S. [VTT Energy (Finland); Broden, K. [Studsvik RadWaste AB (Sweden); Carugati, S.; Brodersen, K. [Forskningscenter Risoe (Denmark); Walderhaug, T. [Icelandic Radiation Protection Institute (Iceland); Helgason, J. [Ekra Geological Consulting (Iceland); Sneve, M.; Hornkjoel, S. [Norwegian Radiation Protection (Norway); Backe, S. [IFE (Norway)

1997-02-01

The Nordic Nuclear Safety Research (NKS) project (AFA-1) focused on safety in the final disposal of long-lived low and medium level radioactive waste and its sub project (AFA-1.2), where this report has been produced, is dealing with the performance analysis of the engineered barrier system (near-field) of the repositories for low-and medium level wastes. The topic intentionally excludes the discussion of the characteristics of the geological host medium. Therefore a more generic discussion of the features of performance analysis is possible independent of the fact that different host media are considered in the Nordic countries. The different waste management systems existing and planned in the Nordic countries are shortly described in the report. In the report main emphasis is paid on the general repositories. Some of the phenomena and interactions relevant for a generic type of repository are discussed as well. Among the different approaches for the development of scenarios for safety and performance analyses one particular method - the Rock Engineering System (RES) - was chosen to be demonstratively tested in a brainstorming session, where the possible interactions and their safety significance were discussed employing a simplified and generic Nordic repository system as the reference system. As an overall impression, the AFA-project group concludes that the use of the RES approach is very easy to learn even during a short discussion session. The use of different ways to indicate the safety significance of various interactions in a graphical user interface increases the clarity. Within the project a simple software application was developed employing a generally available spread sheet programme. The developed tool allows an easy opportunity to link the cell specific comments readily available for the `reader` of the obtained results. A short review of the performance analyses carried out in the Nordic countries for actual projects concerning repositories for

Performance analysis for waste repositories in the nordic countries. Report for project AFA-1.2

International Nuclear Information System (INIS)

Vuori, S.; Broden, K.; Carugati, S.; Brodersen, K.; Walderhaug, T.; Helgason, J.; Sneve, M.; Hornkjoel, S.; Backe, S.

1997-02-01

The Nordic Nuclear Safety Research (NKS) project (AFA-1) focused on safety in the final disposal of long-lived low and medium level radioactive waste and its sub project (AFA-1.2), where this report has been produced, is dealing with the performance analysis of the engineered barrier system (near-field) of the repositories for low-and medium level wastes. The topic intentionally excludes the discussion of the characteristics of the geological host medium. Therefore a more generic discussion of the features of performance analysis is possible independent of the fact that different host media are considered in the Nordic countries. The different waste management systems existing and planned in the Nordic countries are shortly described in the report. In the report main emphasis is paid on the general repositories. Some of the phenomena and interactions relevant for a generic type of repository are discussed as well. Among the different approaches for the development of scenarios for safety and performance analyses one particular method - the Rock Engineering System (RES) - was chosen to be demonstratively tested in a brainstorming session, where the possible interactions and their safety significance were discussed employing a simplified and generic Nordic repository system as the reference system. As an overall impression, the AFA-project group concludes that the use of the RES approach is very easy to learn even during a short discussion session. The use of different ways to indicate the safety significance of various interactions in a graphical user interface increases the clarity. Within the project a simple software application was developed employing a generally available spread sheet programme. The developed tool allows an easy opportunity to link the cell specific comments readily available for the 'reader' of the obtained results. A short review of the performance analyses carried out in the Nordic countries for actual projects concerning repositories for

Muon Tomography for Geological Repositories.

Science.gov (United States)

Woodward, D.; Kudryavtsev, V.; Gluyas, J.; Clark, S. J.; Thompson, L. F.; Klinger, J.; Spooner, N. J.; Blackwell, T. B.; Pal, S.; Lincoln, D. L.; Paling, S. M.; Mitchell, C. N.; Benton, C.; Coleman, M. L.; Telfer, S.; Cole, A.; Nolan, S.; Chadwick, P.

2015-12-01

Cosmic-ray muons are subatomic particles produced in the upper atmosphere in collisions of primary cosmic rays with atoms in air. Due to their high penetrating power these muons can be used to image the content (primarily density) of matter they pass through. They have already been used to image the structure of pyramids, volcanoes and other objects. Their applications can be extended to investigating the structure of, and monitoring changes in geological formations and repositories, in particular deep subsurface sites with stored CO2. Current methods of monitoring subsurface CO2, such as repeat seismic surveys, are episodic and require highly skilled personnel to operate. Our simulations based on simplified models have previously shown that muon tomography could be used to continuously monitor CO2 injection and migration and complement existing technologies. Here we present a simulation of the monitoring of CO2 plume evolution in a geological reservoir using muon tomography. The stratigraphy in the vicinity of the reservoir is modelled using geological data, and a numerical fluid flow model is used to describe the time evolution of the CO2 plume. A planar detection region with a surface area of 1000 m2 is considered, at a vertical depth of 776 m below the seabed. We find that one year of constant CO2 injection leads to changes in the column density of about 1%, and that the CO2 plume is already resolvable with an exposure time of less than 50 days. The attached figure show a map of CO2 plume in angular coordinates as reconstructed from observed muons. In parallel with simulation efforts, a small prototype muon detector has been designed, built and tested in a deep subsurface laboratory. Initial calibrations of the detector have shown that it can reach the required angular resolution for muon detection. Stable operation in a small borehole within a few months has been demonstrated.

Effects of heat from high-level waste on performance of deep geological repository components

International Nuclear Information System (INIS)

1984-11-01

This report discusses the effects of heat on the deep geological repository systems and its different components. The report is focussed specifically on effects due to thermal energy release solely from high-level waste or spent fuel. It reviews the experimental data and theoretical models of the effects of heat both on the behaviour of engineered and natural barriers. A summary of the current status of research and repository development including underground test facilities is presented

Long-term observations programme on the geological environment of a radioactive waste repository in clayey or related formations, implications on the various phases of the project

International Nuclear Information System (INIS)

Manfroy, P.; Raynal, M.; Bonne, A.

1993-01-01

The process of emplacing radioactive waste in deep clayey or related formations involves numerous interdependent actions, the common objective of which is to guarantee optimum isolation of the waste for the durations required. Among these actions, observations on the geological environment will have to extend over a very long period of time, from site characterization to repository closure. All the far-field and near-field observations will constitute the basis and confirmation of the models intended to describe the phenomena which take place in the repository and its surrounding host formation and will have to be taken into account in the repository closure procedures. 6 refs

Experimental conditions and monitoring items of the prototype repository project (PRP). Research document

International Nuclear Information System (INIS)

Sugita, Yutaka; Ito, Akira; Kawakami, Susumu

2003-03-01

Various experiments are ongoing in the underground research facility 'the Hard Rock Laboratory (HRL)' of SKB in Sweden for the geological disposal of the high-level radioactive waste. International joint project Prototype Repository Project (PRP) is one of the experiments in the HRL which has some engineered barrier systems and to study the coupled behavior happening in and around the engineered barrier system. JNC has joined this international joint project PRP to obtain the information of the coupled behavior on such systematic engineered barrier system and to apply the JNC's coupled THMC analytical code to the prediction and back analysis of the PRP. The analytical code will be verified through these analyses in this project. JNC can apply the verified analytical code to assess the coupled behavior in Japan. This report summarizes the experimental conditions and monitoring items of the PRP. (author)

Development of Spherical Near Field Model for Geological Radioactive Waste Repository

International Nuclear Information System (INIS)

Kim, S. Y.; Lee, K. J.; Chang, S. H.; Lee, K. J.; Chang, S. H.

2012-01-01

Modeling for geological radioactive waste repository can be divided into 3 parts. They are near field modeling related to engineered barrier, far field modeling related to natural barrier and biosphere modeling. In order to make the general application for safety assessment of geological waste repository, spherical geometry near field model has been developed. This model can be used quite extensively when users calculate equivalent spherical geometry for specific engineered barrier like equivalent waste radius, equivalent barrier radius and etc. Only diffusion was considered for general purpose but advection part can be updated. Goldsim and Goldsim Radionuclide Transport (RT) module were chosen and used as developing tool for the flexible modeling. Developer can freely make their own model with developer friendly graphic interface by using Goldsim. Furthermore, model with user friendly graphic interface can be developed by using Goldsim Dashboard Authoring module. The model has been validated by comparing the result with that of another model, inserting similar inputs and conditions. The model has been proved to be reasonably operating from the comparison result by validation process. Cylindrical model can be developed as a further work based on the knowledge and experience from this research

Development of Spherical Near Field Model for Geological Radioactive Waste Repository

Energy Technology Data Exchange (ETDEWEB)

Kim, S. Y.; Lee, K. J.; Chang, S. H. [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Lee, K. J.; Chang, S. H. [Khalifa Univ. of Science/Technology and Research, Abu Dhabi (United Arab Emirates)

2012-03-15

Modeling for geological radioactive waste repository can be divided into 3 parts. They are near field modeling related to engineered barrier, far field modeling related to natural barrier and biosphere modeling. In order to make the general application for safety assessment of geological waste repository, spherical geometry near field model has been developed. This model can be used quite extensively when users calculate equivalent spherical geometry for specific engineered barrier like equivalent waste radius, equivalent barrier radius and etc. Only diffusion was considered for general purpose but advection part can be updated. Goldsim and Goldsim Radionuclide Transport (RT) module were chosen and used as developing tool for the flexible modeling. Developer can freely make their own model with developer friendly graphic interface by using Goldsim. Furthermore, model with user friendly graphic interface can be developed by using Goldsim Dashboard Authoring module. The model has been validated by comparing the result with that of another model, inserting similar inputs and conditions. The model has been proved to be reasonably operating from the comparison result by validation process. Cylindrical model can be developed as a further work based on the knowledge and experience from this research.

NWTS program criteria for mined geologic disposal of nuclear waste: repository performance and development criteria. Public draft

Energy Technology Data Exchange (ETDEWEB)

None

1982-07-01

This document, DOE/NWTS-33(3) is one of a series of documents to establish the National Waste Terminal Storage (NWTS) program criteria for mined geologic disposal of high-level radioactive waste. For both repository performance and repository development it delineates the criteria for design performance, radiological safety, mining safety, long-term containment and isolation, operations, and decommissioning. The US Department of Energy will use these criteria to guide the development of repositories to assist in achieving performance and will reevaluate their use when the US Nuclear Regulatory Commission issues radioactive waste repository rules.

NWTS program criteria for mined geologic disposal of nuclear waste: repository performance and development criteria. Public draft

International Nuclear Information System (INIS)

1982-07-01

This document, DOE/NWTS-33(3) is one of a series of documents to establish the National Waste Terminal Storage (NWTS) program criteria for mined geologic disposal of high-level radioactive waste. For both repository performance and repository development it delineates the criteria for design performance, radiological safety, mining safety, long-term containment and isolation, operations, and decommissioning. The US Department of Energy will use these criteria to guide the development of repositories to assist in achieving performance and will reevaluate their use when the US Nuclear Regulatory Commission issues radioactive waste repository rules

Designing shafts for handling high-level radioactive wastes in mined geologic repositories

International Nuclear Information System (INIS)

Hambley, D.F.; Morris, J.R.

1988-01-01

Waste package conceptual designs developed in the United States by the U.S. Department of Energy's Office of Civilian Radioactive Waste Management are the basis for specifying the dimensions and weights of the waste package and transfer cask combinations to be hoisted in the waste handling shafts in mined geologic repositories for high-level radioactive waste. The hoist, conveyance, counterweight, and hoist ropes are then sized. Also taken into consideration are overwind and underwind arrestors and safety features required by the U.S. Nuclear Regulatory Commission. Other design features such as braking systems, chairing system design, and hoisting speed are considered in specifying waste hoisting system parameters for example repository sites

Red-impact project: First results of the evaluations of the impact of P and T on geological disposal

International Nuclear Information System (INIS)

Marivoet, Jan; Vokal, Antonin; Gudowski, Waclaw

2006-01-01

The Red-Impact project (Impact of partitioning, transmutation and waste reduction technologies on the final nuclear waste disposal) is a research project in the 6. Framework Programme of the European Commission. The main objective of the project is to assess the impact of partitioning and transmutation (P and T) on geological disposal and waste management. The project started with the identification of a number of representative fuel cycle scenarios. Five basis scenarios are considered for the evaluations: 2 industrial scenarios and 3 innovative scenarios. Mass flow schemes have been prepared for each basis fuel cycle scenario and the corresponding neutronic calculations have been made. A first list of performance indicators that will be calculated or estimated in the project has been prepared. As a first step the impact of 2 fuel cycle scenarios, the reference 'open cycle' scenario and of the innovative 'fast neutron Gen IV' scenario, on geological repositories in granite and clay formations have been evaluated. The results obtained show that the introduction of innovative fuel cycle scenarios can result in a considerable reduction of the needed size of the geological repository. However, the impact on the radiological consequences is rather limited. Indeed, the maximum dose, which is expected to occur a few tens of thousands year after the disposal of the waste, is essentially due to fission products and their amount is about proportional to the heat generated by nuclear fissions. (authors)

Construction and Operation of a Deep Geological Spent Fuel Repository in Sweden; Some Regulatory Aspects and Challenges

International Nuclear Information System (INIS)

Hedberg, Bengt

2014-01-01

The implementation of a deep geological spent fuel disposal concept in Sweden poses challenges on both implementer and regulator in many aspects. One such challenge is the application of the regulatory framework in a different situation compared to conventional process type nuclear facilities. A specific challenge in this regard is how to understand and address constraints from post-closure safety related to the construction and operation of the repository. The maybe most challenging aspect, however, is the unusually long time frame, i.e. many generations, for realization of the project. This paper addresses some of these challenges from a regulatory perspective. (authors)

Nuclear waste and a deep geological disposal facility

International Nuclear Information System (INIS)

Vokal, A.; Laciok, A.; Vasa, I.

2005-01-01

The paper presents a systematic analysis of the individual areas of research into nuclear waste and deep geological disposal with emphasis on the contribution of Nuclear Research Institute Rez plc to such efforts within international projects, specifically the EURATOM 6th Framework Programme. Research in the area of new advanced fuel cycles with focus on waste minimisation is based on EU's REDIMPACT project. The individual fuel cycles, which are currently studied within the EU, are briefly described. Special attention is paid to fast breeders and accelerator-driven reactor concepts associated with new spent fuel reprocessing technologies. Results obtained so far show that none even of the most advanced fuel cycles, currently under consideration, would eliminate the necessity to have a deep geological repository for a safe storage of residual radioactive waste. As regards deep geological repository barriers, the fact is highlighted that the safety of a repository is assured by complementary engineered and natural barriers. In order to demonstrate the safety of a repository, a deep insight must be gained into any and all of the individual processes that occur inside the repository and thus may affect radioactivity releases beyond the repository boundaries. The final section of the paper describes methods of radioactive waste conditioning for its disposal in a repository. Research into waste matrices used for radionuclide immobilisation is also highlighted. (author)

Analysis of the geological stability of a hypothetical radioactive waste repository in a bedded salt formation

International Nuclear Information System (INIS)

Tierney, M.S.; Lusso, F.; Shaw, H.R.

1978-01-01

This document reports on the development of mathematical models used in preliminary studies of the long-term safety of radioactive wastes deeply buried in bedded salt formations. Two analytical approaches to estimating the geological stability of a waste repository in bedded salt are described: (a) use of probabilistic models to estimate the a priori likelihoods of release of radionuclides from the repository through certain idealized natural and anthropogenic causes, and (b) a numerical simulation of certain feedback effects of emplacement of waste materials upon ground-water access to the repository's host rocks. These models are applied to an idealized waste repository for the sake of illustration

Addressing issues raised by stakeholders in the development of a deep geological repository in the Czech Republic

International Nuclear Information System (INIS)

Sumberova, Vera

2004-01-01

The mission of the Radioactive Waste Repository Authority (RAWRA) is to ensure the safe disposal of all existing and future radioactive waste. In order to fulfil this task RAWRA, in addition to the operation of radioactive waste repositories in the Czech Republic, coordinates all those activities relating to the construction of a deep geological repository. This long-term goal implies first creating and then building upon the public's confidence in the decision making process and the project as a whole as well as in RAWRA as a competent and efficient implementer since clearly public acceptance is an essential condition for a successful final outcome. Since its establishment in 1997 RAWRA has been looking for ways in which to inform the public about its activities and how to involve the various stakeholders in the development process. The communication tools employed to achieve this goal have, to date, depended on the specific stage of the process but RAWRA has aimed at a continuous improvement in its activities; consequently a large number of changes have been made to RAWRA's policy and approach in recent years. This paper, which aims to describe RAWRA's dialogue with stakeholders (mainly local communities), provides examples of the way in which issues raised by stakeholders concerning a repository are reflected in RAWRA's approach. (author)

Safety assessment methodology for waste repositories in deep geological formations

International Nuclear Information System (INIS)

Chapuis, A.M.; Lewi, J.; Pradel, J.; Queniart, D.; Raimbault, P.; Assouline, M.

1986-06-01

The long term safety of a nuclear waste repository relies on the evaluation of the doses which could be transferred to man in the future. This implies a detailed knowledge of the medium where the waste will be confined, the identification of the basic phenomena which govern the migration of the radionuclides and the investigation of all possible scenarios that may affect the integrity of the barriers between the waste and the biosphere. Inside the Institute of protection and nuclear safety of the French Atomic Energy Commission (CEA/IPSN), the Department of the Safety Analysis (DAS) is currently developing a methodology for assessing the safety of future geological waste repositories, and is in charge of the modelling development, while the Department of Technical Protection (DPT) is in charge of the geological experimental studies. Both aspects of this program are presented. The methodology for risk assessment stresses the needs for coordination between data acquisition and model development which should result in the obtention of an efficient tool for safety evaluation. Progress needs to be made in source and geosphere modelling. Much more sophisticated models could be used than the ones which is described; however sensitivity analysis will determine the level of sophistication which is necessary to implement. Participation to international validation programs are also very important for gaining confidence in the approaches which have been chosen

U.S. Department of Energy approaches to the assessment of radionuclide migration for the geologic repository program

International Nuclear Information System (INIS)

Luik, A.E. van; Apted, M.J.

1988-01-01

Potential radionuclide migration in geologic repositories is being addressed by the U.S. Department of Energy's Office of Civilian Radioactive Waste Management through its Office of Geologic Repositories (OGR). A diversity of geohydrologic settings is being investigated: unsaturated tuff, saturated basalt, and bedded salt. A number of approaches to assessing potential migration are being considered. Mass transfer is prominent among near-field approaches. For far-field analysis of migration in the geosphere, detailed characterizations of potential repository sites will lead to site-specific models describing radionuclide migration for a variety of postulated release scenarios. Finite-element and finite-difference codes are being used and developed to solve the mathematical equations pertinent to far-field assessments. Computational approaches presently in use generally require distribution coefficients to estimate the retardation of specific radionuclides with respect to the transport rate of water. 26 refs

Pre-construction geologic section along the cross drift through the potential high-level radioactive waste repository, Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

Potter, C.J.; Day, W.C.; Sweetkind, D.S.; Juan, C.S.; Drake, R.M. II

1998-01-01

As part of the Site Characterization effort for the US Department of Energy's Yucca Mountain Project, tunnels excavated by tunnel boring machines provide access to the volume of rock that is under consideration for possible underground storage of high-level nuclear waste beneath Yucca Mountain, Nevada. The Exploratory Studies Facility, a 7.8-km-long, 7.6-m-diameter tunnel, has been excavated, and a 2.8-km-long, 5-m-diameter Cross Drift will be excavated in 1998 as part of the geologic, hydrologic and geotechnical evaluation of the potential repository. The southwest-trending Cross Drift branches off of the north ramp of the horseshoe-shaped Exploratory Studies Facility. This report summarizes an interpretive geologic section that was prepared for the Yucca Mountain Project as a tool for use in the design and construction of the Cross Drift

The Swedish approach to siting of a deep geological repository and interaction with the public

International Nuclear Information System (INIS)

Thegerstroem, C.

1993-01-01

The planned process for siting of a deep geological repository for encapsulated spent nuclear fuel in Sweden was presented in the 1992 SKB R and D programme. A first phase of the repository operation will be limited to disposal of a small amount of encapsulated spent nuclear fuel (approximately 800 tons). This phase will be followed by an evaluation of experiences as well as alternative options before deciding if, when and how to proceed with disposal of the remaining amounts of spent fuel. During the first phase it will be possible to retrieve the waste. Siting is planned to be done in stages. The field studies and safety assessments performed strongly indicate that it is possible to find geological suitable sites within many regions of Sweden. The potential for fulfilling safety requirements will be a crucial factor in site-selection. Local interest in, and attitude to a repository siting will play an important role in the siting process. It is important that an atmosphere of trust and openness can be established. Extensive geological site characterization work will be carried out at the sites selected and studies of other technical, social, economical or political matters will be equally important. Public communication and local participation will form an essential part of the siting programme from the outset. 3 refs., 3 figs

Status of technologies related to the isolation of radioactive wastes in geologic repositories

Energy Technology Data Exchange (ETDEWEB)

Irish, E R [International Atomic Energy Agency, Vienna (Austria). Div. of Nuclear Safety and Environmental Protection; Cooley, C R [Department of Energy, Washington, DC (USA). Office of Nuclear Waste Management

1980-09-01

The authors present an overview of the status of technologies relevant to the isolation of radioactive wastes in geologic repositories. In addition to summarizing scientific and technical work on waste forms and packages, the: a) importance of the systems viewpoint, b) importance of modeling, c) need for site-specific investigations, d) consideration of future sub-surface human activities and e) prospects for successful isolation are discussed. It is concluded that successful isolation of radioactive wastes from the biosphere appears technically feasible for periods of thousands of years provided that the systems view is used in repository siting and design.

Use of Groundwater Lifetime Expectancy for the Performance Assessment of Deep Geologic Radioactive Waste Repositories.

Science.gov (United States)

Cornaton, F.; Park, Y.; Normani, S.; Sudicky, E.; Sykes, J.

2005-12-01

Long-term solutions for the disposal of toxic wastes usually involve isolation of the wastes in a deep subsurface geologic environment. In the case of spent nuclear fuel, the safety of the host repository depends on two main barriers: the engineered barrier and the natural geological barrier. If radionuclide leakage occurs from the engineered barrier, the geological medium represents the ultimate barrier that is relied upon to ensure safety. Consequently, an evaluation of radionuclide travel times from the repository to the biosphere is critically important in a performance assessment analysis. In this study, we develop a travel time framework based on the concept of groundwater lifetime expectancy as a safety indicator. Lifetime expectancy characterizes the time radionuclides will spend in the subsurface after their release from the repository and prior to discharging into the biosphere. The probability density function of lifetime expectancy is computed throughout the host rock by solving the backward-in-time solute transport equation subject to a properly posed set of boundary conditions. It can then be used to define optimal repository locations. In a second step, the risk associated with selected sites can be evaluated by simulating an appropriate contaminant release history. The proposed methodology is applied in the context of a typical Canadian Shield environment. Based on a statistically-generated three-dimension network of fracture zones embedded in the granitic host rock, the sensitivity and the uncertainty of lifetime expectancy to the hydraulic and dispersive properties of the fracture network, including the impact of conditioning via their surface expressions, is computed in order to demonstrate the utility of the methodology.

Archive of Geosample Data and Information from the U.S. Geological Survey (USGS) Coastal and Marine Geology Program (CMGP) Pacific Coastal and Marine Science Center (PCMSC) Samples Repository

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The U.S. Geological Survey Coastal and Marine Geology Program (CMGP) Pacific Coastal and Marine Science Center (PCMSC) Samples Repository is a partner in the Index...

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 10. Repository preconceptual design studies: granite

International Nuclear Information System (INIS)

1978-04-01

This volume, Volume 10 ''Repository Preconceptual Design Studies: Granite,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This document describes a preconceptual design for a nuclear waste storage facility in granite. The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area, and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/11, ''Drawings for Repository Preconceptual Design Studies: Granite.''

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 8. Repository preconceptual design studies: salt

International Nuclear Information System (INIS)

1978-04-01

This volume, Volume 8 ''Repository Preconceptual Design Studies: Salt,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This document describes a preconceptual design for a nuclear waste storage facility in salt. The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area, and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/9, ''Drawings for Repository Preconceptual Design Studies: Salt.''

Geological repository layout for radioactive high level long lived waste in argillite

International Nuclear Information System (INIS)

Gaussen, JL

2006-01-01

In the framework of the 1991 French radioactive waste act, ANDRA has studied the feasibility of a geological repository in the argillite layer of the Bure site for high level long lived waste. This presentation is focussed on the underground facilities which constitute the specific component of this project. The preliminary underground layout which has been elaborated is based on four categories of data: - the waste characteristics and inventory; - the geological properties of the host argillite; - the long term performance objectives of the repository; - the specifications in terms of operation and reversibility. The underground facilities consist of two types of works: the access works (shafts and drifts) and the disposal cells. The function of the access works is to permit the implementation of two concurrent activities: the nuclear operations (transfer and emplacement of the disposal packages into the disposal cells) and the construction of the next disposal cells. The design of the drifts network which matches up to this function is also influenced by two other specifications: the minimization of the drift dimensions in order to limit their influence on the integrity of the geological formation and the necessity of a safe ventilation in case of fire. The resulting layout is a network of 4 parallel drifts (2 of them being dedicated to the operation, the other two being dedicated to the construction activities). The average diameter of these access drifts is 7 meters. The link between the surface and the underground is ensured by 4 shafts. The most important function of the disposal cells is to contribute to the long term performance of the repository. In this regard, the thermal and geotechnical considerations play an important role. The B wastes (intermediate level wastes) are not (or not very) exothermic. Consequently, the design of their disposal cells result mainly from geotechnical considerations. The disposal packages (made of concrete) are piled up in

Sectoral Plan 'Deep Geological Disposal', Stage 2. Proposed site areas for the surface facilities of the deep geological repositories as well as for their access infrastructure. Annexes

International Nuclear Information System (INIS)

2011-12-01

In line with the provisions of the nuclear energy legislation, the sites for deep geological disposal of Swiss radioactive waste are selected in a three-stage Sectoral Plan process (Sectoral Plan for Deep Geological Disposal). The disposal sites are specified in Stage 3 of the selection process with the granting of a general licence in accordance with the Nuclear Energy Act. The first stage of the process was completed on 30 th November 2011, with the decision of the Federal Council to incorporate the six geological siting regions proposed by the National Cooperative for the Disposal of Radioactive Waste (NAGRA) into the Sectoral Plan for Deep Geological Disposal, for further evaluation in Stage 2. The decision also specifies the planning perimeters within which the surface facilities and shaft locations for the repositories will be constructed. In the second stage of the process, at least two geological siting regions each will be specified for the repository for low- and intermediate-level waste (L/ILW) and for the high-level waste (HLW) repository and these will undergo detailed geological investigation in Stage 3. For each of these potential siting regions, at least one location for the surface facility and a corridor for the access infrastructure will also be specified. NAGRA is responsible, at the beginning of Stage 2, for submitting proposals for potential locations for the surface facilities and their access infrastructure to the Federal Office of Energy (SFOE); these are then considered by the regional participation bodies in the siting regions. The general report and the present annexes volume document these proposals. In Stage 2, under the lead of the SFOE, socio-economic-ecological studies will also be carried out to investigate the impact of a repository project on the environment, economy and society. The present reports also contain the input data to be provided by NAGRA for the generic (site-independent) part of these impact studies. A meaningful

The application of geological computer modelling systems to the characterisation and assessment of radioactive waste repositories

International Nuclear Information System (INIS)

White, M.J.; Del Olmo, C.

1996-01-01

The deep disposal of radioactive waste requires the collection and analysis of large amounts of geological data. These data give information on the geological and hydrogeological setting of repositories and research sites, including the geological structure and the nature of the groundwater. The collection of these data is required in order to develop an understanding of the geology and the geological evolution of sites and to provide quantitative information for performance assessments. An integrated approach to the interpretation and provision of these data is proposed in this paper, via the use of computer systems, here termed geological modelling systems. Geological modelling systems are families of software programmes which allow the incorporation of site investigation data into integrated 3D models of sub-surface geology

Sectoral Plan 'Deep Geological Disposal', Stage 2. Proposed site areas for the surface facilities of the deep geological repositories as well as for their access infrastructure. General report

International Nuclear Information System (INIS)

2011-12-01

In line with the provisions of the nuclear energy legislation, the sites for deep geological disposal of Swiss radioactive waste are selected in a three-stage Sectoral Plan process (Sectoral Plan for Deep Geological Disposal). The disposal sites are specified in Stage 3 of the selection process with the granting of a general licence in accordance with the Nuclear Energy Act. The first stage of the process was completed on 30 th November 2011, with the decision of the Federal Council to incorporate the six geological siting regions proposed by the National Cooperative for the Disposal of Radioactive Waste (NAGRA) into the Sectoral Plan for Deep Geological Disposal, for further evaluation in Stage 2. The decision also specifies the planning perimeters within which the surface facilities and shaft locations for the repositories will be constructed. In the second stage of the process, at least two geological siting regions each will be specified for the repository for low- and intermediate-level waste (L/ILW) and for the high-level waste (HLW) repository and these will undergo detailed geological investigation in Stage 3. For each of these potential siting regions, at least one location for the surface facility and a corridor for the access infrastructure will also be specified. NAGRA is responsible, at the beginning of Stage 2, for submitting proposals for potential locations for the surface facilities and their access infrastructure to the Federal Office of Energy (SFOE); these are then considered by the regional participation bodies in the siting regions. The present report and its annexes volume document these proposals. In Stage 2, under the lead of the SFOE, socio-economic-ecological studies will also be carried out to investigate the impact of a repository project on the environment, economy and society. The present reports also contain the input data to be provided by NAGRA for the generic (site-independent) part of these impact studies. A meaningful discussion

Geologic software for nuclear waste repository studies: A quality assurance program

International Nuclear Information System (INIS)

Figuli, S.; English, S.L.

1987-04-01

This paper discusses a Quality Assurance (QA) program that Kent State University (KSU) has implemented for the development of geologic software. The software being developed at KSU will be used in the site characterization of nuclear waste repositories and must meet the requirements of federal regulations. This QA program addresses the development of models that will be used in the evaluation of the long-term climatic stability of three sites in the western US

Problems of geologic survey of high level radioactive waste repositories illustrated on the testing site in the Melechov Massif

International Nuclear Information System (INIS)

Mlcoch, B.

1997-01-01

Major attention is paid to problems associated with the geologic maps of the prospective repository site, which lies within the Bohemian Massif. Structural geology, survey through boreholes, and primary database are also discussed briefly. (P.A.)

Geology of the Yucca Mountain Region, Chapter in Stuckless, J.S., ED., Yucca Mountain, Nevada - A Proposed Geologic Repository for High-Level Radioactive Waste

International Nuclear Information System (INIS)

J.S. Stuckless; D. O'Leary

2006-01-01

Yucca Mountain has been proposed as the site for the Nation's first geologic repository for high-level radioactive waste. This chapter provides the geologic framework for the Yucca Mountain region. The regional geologic units range in age from late Precambrian through Holocene, and these are described briefly. Yucca Mountain is composed dominantly of pyroclastic units that range in age from 11.4 to 15.2 Ma. The proposed repository would be constructed within the Topopah Spring Tuff, which is the lower of two major zoned and welded ash-flow tuffs within the Paintbrush Group. The two welded tuffs are separated by the partly to nonwelded Pah Canyon Tuff and Yucca Mountain Tuff, which together figure prominently in the hydrology of the unsaturated zone. The Quaternary deposits are primarily alluvial sediments with minor basaltic cinder cones and flows. Both have been studied extensively because of their importance in predicting the long-term performance of the proposed repository. Basaltic volcanism began about 10 Ma and continued as recently as about 80 ka with the eruption of cones and flows at Lathrop Wells, approximately 10 km south-southwest of Yucca Mountain. Geologic structure in the Yucca Mountain region is complex. During the latest Paleozoic and Mesozoic, strong compressional forces caused tight folding and thrust faulting. The present regional setting is one of extension, and normal faulting has been active from the Miocene through to the present. There are three major local tectonic domains: (1) Basin and Range, (2) Walker Lane, and (3) Inyo-Mono. Each domain has an effect on the stability of Yucca Mountain

Key radionuclides and parameters that determine performance of geologic repositories for high-level radioactive wastes

International Nuclear Information System (INIS)

Joonhong Ahn; Atsuyuki Suzuki

1993-01-01

This paper presents results of a mathematical analysis for performance of the engineered barriers of high-level radioactive waste repositories. The main body of the mathematical model developed in this study is mass transport of actinides in a bentonite region. In an analysis of actinide transport, radioactive decay chain and effects of low solubilities must be taken into account. In many previous models for mass transport in engineered barriers including radioactive decay chain, however, boundary conditions at the interface between the waste form and the bentonite region cannot be determined flexibly. In some models, solubility-limited boundary condition is assumed for all the members in a chain. In order to investigate what are key radionuclides and parameters that control performance of engineered barriers of a geologic repository, we must evaluate mass transport with the source boundary condition determined by a detailed analysis on mass transfer at the boundary. In this study, we developed a mathematical model, which can determine whether the inner boundary condition is solubility-limited or congruent release, based on a mathematical analysis for mass transfer at the glass dissolution location, and how long the solubility-limited boundary condition applies. Based on the mathematical model, we point out radionuclides and parameters that have primary influences on the performance of a repository, and investigate a reasonable strategy for coupling geologic disposal and partitioning of those key radionuclides from the standpoint of reducing hazard of geologic disposal. (authors). 4 tabs., 2 figs., 8 refs

Archive of Geosample Data and Information from the U.S. Geological Survey (USGS) Coastal and Marine Geology Program (CMGP) Woods Hole Coastal and Marine Science Center (WHCMSC) Samples Repository

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The U.S. Geological Survey Coastal and Marine Geology Program (CMGP) Woods Hole Coastal and Marine Science Center (WHCMSC) Samples Repository is a partner in the...

Archive of Geosample Data and Information from the U.S. Geological Survey (USGS) Coastal and Marine Geology Program (CMGP) St. Petersburg Coastal and Marine Science Center (SPCMSC) Samples Repository

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The U.S. Geological Survey Coastal and Marine Geology Program (CMGP) St. Petersburg Coastal and Marine Science Center (SPCMSC) Samples Repository is a partner in the...

Analysis on the use of engineered barriers for geologic isolation of spent fuel in a reference salt site repository

International Nuclear Information System (INIS)

Cloninger, M.O.; Cole, C.R.; Washburn, J.F.

1980-12-01

A perspective on the potential durability and effectiveness requirements for the waste form, container and other engineered barriers for geologic disposal of spent nuclear fuel has been developed. This perspective is based on calculated potential doses to individuals who may be exposed to radioactivity released from a repository via a groundwater transport pathway. These potential dose commitments were calculated with an integrated geosphere transport and bioshpere transport model. A sensitivity analysis was accomplished by varying four important system parameters, namely the waste radionuclide release rate from the repository, the delay prior to groundwater contact with the waste (leach initiation), aquifer flow velocity and flow path length. The nuclide retarding capacity of the geologic media, a major determinant of the isolation effectiveness, was not varied as a parameter but was held constant for a particular reference site. This analysis is limited to looking only at engineered barriers whose net effect is either to delay groundwater contact with the waste form or to limit the rate of release of radionuclides into the groundwater once contact has occurred. The analysis considers only leach incident scenarios, including a water well intrusion into the groundwater near a repository, but does not consider other human intrusion events or catastrophic events. The analysis has so far been applied to a reference salt site repository system and conclusions are presented.Basically, in nearly all cases, the regional geology is the most effective barrier to release of radionuclides to the biosphere; however, for long-lived isotopes of carbon, technetium and iodine, which were poorly sorbed on the geologic media, the geology is not very effective once a leach incident is initiated

From the repository to the deep geological repository - and back to the Terrain surface?

International Nuclear Information System (INIS)

Lahodynsky, R.

2011-01-01

How deep is 'safe'? How long is long-term? How and for how long will something be isolated? Which rock, which formation and which location are suitable? A repository constructed for the safekeeping of radioactive or highly toxic wastes can be erected either on the surface, near the surface or underground. Radioactive waste is currently often stored at near-surface locations. The storage usually takes place nearby of a nuclear power plant in pits or concrete tombs (vaults). However, repositories can also be found in restricted areas, e.g. near nuclear weapon production or reprocessing plants (WAA) or nuclear weapons test sites (including Tomsk, Russia, Hanford and Nevada desert, USA), or in extremely low rainfall regions (South Africa). In addition there are disused mines which are now used as underground repositories. Low-level and medium-active (SMA) but also high-level waste (HAA) are stored at these types of sites (NPP, WAA, test areas, former mines). In Russia (Tomsk, Siberia) liquid radioactive waste has been injected into deep geological formations for some time (Minatom, 2001). However, all these locations are not the result of a systematic, scientific search or a holistic process for finding a location, but the result of political decisions, sometimes ignoring scientific findings. Why underground storage is given preference over high-security landfill sites (HSD) often has economic reasons. While a low safety standard can significantly reduce the cost of an above-ground high-security landfill as a waste disposal depot, spending remains high, especially due to the need for capital formation to cover operating expenses after filling the HSD. In the case of underground storage, on the other hand, no additional expenses are required for the period after backfilling. The assumption of lower costs for a deep repository runs through the past decades and coincides with the assumption that the desired ideal underground conditions actually exist and will

Standard guide for characterization of spent nuclear fuel in support of geologic repository disposal

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This guide provides guidance for the types and extent of testing that would be involved in characterizing the physical and chemical nature of spent nuclear fuel (SNF) in support of its interim storage, transport, and disposal in a geologic repository. This guide applies primarily to commercial light water reactor (LWR) spent fuel and spent fuel from weapons production, although the individual tests/analyses may be used as applicable to other spent fuels such as those from research and test reactors. The testing is designed to provide information that supports the design, safety analysis, and performance assessment of a geologic repository for the ultimate disposal of the SNF. 1.2 The testing described includes characterization of such physical attributes as physical appearance, weight, density, shape/geometry, degree, and type of SNF cladding damage. The testing described also includes the measurement/examination of such chemical attributes as radionuclide content, microstructure, and corrosion product c...

Guidelines for the operation and closure of deep geological repositories for the disposal of high level and alpha bearing wastes

International Nuclear Information System (INIS)

1991-10-01

The operation and closure of a deep geological repository for the disposal of high level and alpha bearing wastes is a long term project involving many disciplines. This unique combination of nuclear operations in a deep underground location will require careful planning by the operating organization. The basic purpose of the operation stage of the deep repository is to ensure the safe disposal of the radioactive wastes. The purpose of the closure stage is to ensure that the wastes are safely isolated from the biosphere, and that the surface region can be returned to normal use. During these two stages of operation and closure, it is essential that both workers and the public are safely protected from radiation hazards, and that workers are protected from the hazards of working underground. For these periods of the repository, it is essential to carry out monitoring for purposes of radiological protection, and to continue testing and investigations to provide data for repository performance confirmation and for final safety assessment. Over the lengthy stages of operation and closure, there will be substantial feedback of experience and generation of site data. These will lead both to improved quality of operation and a better understanding of the site characteristics, thereby enhancing the confidence in the ability of the repository system to isolate the waste and protect future generations. 15 refs

Radioactive waste disposal programme and siting regions for geological deep repositories. Executive summary. November 2008; Entsorgungsprogramm und Standortgebiete fuer geologische Tiefenlager. Zusammenfassung. November 2008

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-11-15

There are radioactive wastes in Switzerland. Since many decades they are produced by the operation of the five nuclear power plants, by medicine, industry and research. Important steps towards the disposal of these wastes are already realized; the corresponding activities are practised. This particularly concerns handling and packaging of the radioactive wastes, their characterization and inventory, as well as the interim storage and the inferred transportations. Preparatory works in the field of scientific research on deep geological repositories have allowed to acquire high level of technical and scientific expertise in that domain. The feasibility of building long-term safe geological repositories in Switzerland was demonstrated for all types of radioactive wastes; the demonstration was accepted by the Federal Council. There is enough knowledge to propose geological siting regions for further works. The financial funds already accumulated guaranty the financing of the dismantling of the power plants as well as building deep geological repositories for the radioactive wastes. The regulations already exist and the organisational arrangements necessary for the fruitful continuation of the works already done have been taken. The programme of the disposal of radioactive wastes also describes the next stages towards the timely realization of the deep repositories as well as the level of the financial needs. The programme is updated every five years, checked by the regulatory bodies and accepted by the Federal Council who reports to the parliament. The process of choosing a site, which will be completed in the next years, is detailed in the conceptual part of the programme for deep geological repositories. The NAGRA proposals are based exclusively on technical and scientific considerations; the global evaluation taking into account also political considerations has to be performed by the authorities and the Federal Council. The programme states that at the beginning of

Geologic repositories for radioactive waste: the nuclear regulatory commission geologic comments on the environmental assessment

International Nuclear Information System (INIS)

Justus, P.S.; Trapp, J.S.; Westbrook, K.B.; Lee, R.; Blackford, M.B.; Rice, B.

1985-01-01

The NRC staff completed its review of the Environmental Assessments (EAs) issued by the Department of Energy (DOE) in December, 1984, in support of the site selection processes established by the Nuclear Waste Policy Act of 1982 (NWPA). The EAs contain geologic information on nine sites that DOE has identified as potentially acceptable for the first geologic repository in accordance with the requirements of NWPA. The media for the sites vary from basalt at Hanford, Washington, tuff at Yucca Mountain, Nevada, bedded salt in the Palo Duro Basin, Texas and Paradox Basin, Utah, to salt domes in Mississippi and Louisiana. Despite the diversity in media there are common areas of concern for all sites. These include; structural framework and pattern, rates of tectonic and seismic activity, characterization of subsurface features, and stratigraphic thickness, continuity and homogeneity. Site-specific geologic concerns include: potential volcanic and hydrothermal activity at Yucca Mountain, potential hydrocarbon targets and deep basalt and sub-basalt structure at Hanford, and potential dissolution at all salt sites. The NRC comments were influenced by the performance objectives and siting criteria of 10 CFR Part 60 and the environmental protection criteria in 40 CFR Part 191, the applicable standards proposed by EPA. In its review the NRC identified several areas of geologic concern that it recommended DOE re-examine to determine if alternative or modified conclusions are appropriate

Evaluation of alternative shaft-sinking techniques for high-level nuclear waste (HLW) deep geologic repositories. Final report (Task 3), June 1981-July 1982

International Nuclear Information System (INIS)

Gonano, L.; Findley, D.; Wildanger, W.; Gates, R.; Phillips, S.

1983-03-01

This report represents the results of Task 3 of US Nuclear Regulatory Commission (NRC) Contract, Technical Assistance for Repository Design. The purpose of the complete project is to provide NRC with technical assistance for the following reasons: To enable the focused, adequate review by NRC of aspects related to design and construction of an in situ test facility and final geologic repository, as presented in US Department of Energy (DOE) Site Characterization Reports (SRC), To ascertain that the DOE site characterization program will provide, as far as possible, all the information necessary to permit a review to be conducted by NRC of a license application for construction authorization. It is assumed that the Site Characterization Report and License Application will describe the exploratory shaft and concept designs for the repository shafts. This report provides a comparative evaluation of various shaft sinking techniques for production shafts for a repository. The primary comparative evaluation has been conducted for 14-ft internal diameter shafts developed in two composite media using four different methods of sinking/lining. The technical, cost and schedule comparisons draw a major distinction between shafts sunk blind and those which utilize bottom access. Based on the system of ranking introduced to grade the significant attributes of each method and the resulting design, it is concluded that for application to repository access, no one particular method of sinking exhibits a clear overall superiority. When a specific site is made available for a study of the most suitable shaft sinking methods, it will be necessary to establish actual geological conditions and technological capabilities and the comparisons presented herein reviewed accordingly

Shear-induced Fracture Slip and Permeability Change. Implications for Long-term Performance of a Deep Geological Repository

International Nuclear Information System (INIS)

Min, Ki-Bok; Stephansson, Ove

2009-03-01

Opening of fractures induced by shear dilation or normal deformation can be a significant source of fracture permeability change in jointed rock, which is important for the performance assessment of geological repositories for spent nuclear fuel. As the repository generates heat and later cools the fluid-carrying ability of the rocks becomes a dynamic variable during the lifespan of the repository. Heating causes expansion of the rock close to the repository and, at the same time, contraction close to the surface. During the cooling phase of the repository, the opposite takes place. Heating and cooling together with the virgin stress can induce shear dilation of fractures and deformation zones and change the flow field around the repository. The objectives of this project are to examine the contribution of thermal stress to the shear slip of fracture in mid- and far-field around a KBS-3 type of repository and to investigate the effect of evolution of stress on the rock mass permeability. The first part of the study is about the evolution of thermal stresses in the rock during the lifetime of the repository. Critical sections of heat generated stresses around the repository are selected and classified. Fracture data from Forsmark is used to establish fracture network models (DFN) and the models are subjected to the sum of virgin stress and thermal stresses and the shear slip and related permeability change are studied. In the first part of this study, zones of fracture shear slip were examined by conducting a three-dimensional, thermo-mechanical analysis of a spent fuel repository model. Stress evolutions of importance for fracture shear slip are: (1) comparatively high horizontal compressive thermal stress at the repository level, (2) generation of vertical tensile thermal stress right above the repository, (3) horizontal tensile stress near the surface, which can induce tensile failure, and generation of shear stresses at the corners of the repository. In the

Shear-induced Fracture Slip and Permeability Change. Implications for Long-term Performance of a Deep Geological Repository

Energy Technology Data Exchange (ETDEWEB)

Min, Ki-Bok (School of Civil, Environmental and Mining Engineering, Univ. of Adelaide, Adelaide (Australia)); Stephansson, Ove (Steph Rock Consulting AB, Berlin (Germany))

2009-03-15

Opening of fractures induced by shear dilation or normal deformation can be a significant source of fracture permeability change in jointed rock, which is important for the performance assessment of geological repositories for spent nuclear fuel. As the repository generates heat and later cools the fluid-carrying ability of the rocks becomes a dynamic variable during the lifespan of the repository. Heating causes expansion of the rock close to the repository and, at the same time, contraction close to the surface. During the cooling phase of the repository, the opposite takes place. Heating and cooling together with the virgin stress can induce shear dilation of fractures and deformation zones and change the flow field around the repository. The objectives of this project are to examine the contribution of thermal stress to the shear slip of fracture in mid- and far-field around a KBS-3 type of repository and to investigate the effect of evolution of stress on the rock mass permeability. The first part of the study is about the evolution of thermal stresses in the rock during the lifetime of the repository. Critical sections of heat generated stresses around the repository are selected and classified. Fracture data from Forsmark is used to establish fracture network models (DFN) and the models are subjected to the sum of virgin stress and thermal stresses and the shear slip and related permeability change are studied. In the first part of this study, zones of fracture shear slip were examined by conducting a three-dimensional, thermo-mechanical analysis of a spent fuel repository model. Stress evolutions of importance for fracture shear slip are: (1) comparatively high horizontal compressive thermal stress at the repository level, (2) generation of vertical tensile thermal stress right above the repository, (3) horizontal tensile stress near the surface, which can induce tensile failure, and generation of shear stresses at the corners of the repository. In the

Optimization method for dimensioning a geological HLW waste repository

International Nuclear Information System (INIS)

Ouvrier, N.; Chaudon, L.; Malherbe, L.

1990-01-01

This method was developed by the CEA to optimize the dimensions of a geological repository by taking account of technical and economic parameters. It involves optimizing radioactive waste storage conditions on the basis of economic criteria with allowance for specified thermal constraints. The results are intended to identify trends and guide the choice from among available options: simple and highly flexible models were therefore used in this study, and only nearfield thermal constraints were taken into consideration. Because of the present uncertainty on the physicochemical properties of the repository environment and on the unit cost figures, this study focused on developing a suitable method rather than on obtaining definitive results. The optimum values found for the two media investigated (granite and salt) show that it is advisable to minimize the interim storage time, implying the containers must be separated by buffer material, whereas vertical spacing may not be required after a 30-year interim storage period. Moreover, the boreholes should be as deep as possible, on a close pitch in widely spaced handling drifts. These results depend to a considerable extent on the assumption of high interim storage costs

The function of packing materials in a high-level nuclear waste repository and some candidate materials: Salt Repository Project

International Nuclear Information System (INIS)

Bunnell, L.R.; Shade, J.W.

1987-03-01

Packing materials should be included in waste package design for a high-level nuclear waste repository in salt. A packing material barrier would increase confidence in the waste package by alleviating possible shortcomings in the present design and prolonging confinement capabilities. Packing materials have been studied for uses in other geologic repositories; appropriately chosen, they would enhance the confinement capabilities of salt repository waste packages in several ways. Benefits of packing materials include retarding or chemically modifying brines to reduce corrosion of the waste package, providing good thermal conductivity between the waste package and host rock, retarding or absorbing radionuclides, and reducing the massiveness of the waste package. These benefits are available at low percentage of total repository cost, if the packing material is properly chosen and used. Several candidate materials are being considered, including oxides, hydroxides, silicates, cement-based mixtures, and clay mixtures. 18 refs

Canada's deep geological repository for used nuclear fuel - the geoscientific site evaluation process

Energy Technology Data Exchange (ETDEWEB)

Belfadhel, M.B.; Blyth, A.; Desroches, A.; Hirschorn, S.; Mckelvie, J.; Sanchez-Rico Castejon, M.; Parmenter, A.; Urrutia-Bustos, A.; Vorauer, A., E-mail: mbenbelfadhel@nwmo.ca [Nuclear Waste Management Organization, Toronto, ON (Canada)

2014-07-01

The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for the long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable crystalline or sedimentary rock formation. In May 2010, the NWMO initiated a nine-step site selection process to find an informed and willing community to host the project. This paper describes the approach, methods and criteria being used to assess the geoscientific suitability of communities currently involved in the site selection process. The social, cultural and economic aspects of the assessment are discussed in a companion paper. (author)

System analysis methods for geological repository of high level radioactive waste in granite

International Nuclear Information System (INIS)

Chen Weiming; Wang Ju; Li Yunfeng; Jin Yuanxin; Zhao Honggang

2009-01-01

Taking Beishan granite site as an example, this paper proposes the conceptual and structural design of repository for high level radioactive waste at first. Then the function, structure, environment and evolution of the repository are described by the methodology of system analysis. Based on these designs and descriptions, a calculation model for the repository is developed with software GoldSim. At last, this calculation model is applied to emulate the space-time distribution of repository radiotoxicity, to analyze the sensitivity of parameters in the model, to optimize the design parameters, and to predict and assess the repository performance. The results of this study can provide technical supports for resources allocation and coordination of R and D projects. (authors)

Displays for promotion of public understanding of geological repository concept and the spatial scale

International Nuclear Information System (INIS)

Shobu, Nobuhiro; Kashiwazaki, Hiroshi

2003-05-01

Japan Nuclear Cycle Development Institutes (JNC) has a few thousands of short term visitors to Geological Isolation Basic Research Facility of Tokai works in every year. From the viewpoint of promotion of the visitor's understanding and also smooth communication between researchers and visitors, the explanation of the technical information on geological disposal should be carried out in more easily understandable methods, as well as conventional tour to the engineering-scale test facility (ENTRY). This paper reports on the background information and the appearance of displays, which were installed at ENTRY, to promote public understanding of geological repository concept and the spatial scale. They have been practically used as one of the explanation tools to support visitor's understanding. (author)

Geology of the Yucca Mountain Region, Chapter in Stuckless, J.S., ED., Yucca Mountain, Nevada - A Proposed Geologic Repository for High-Level Radioactive Waste

Energy Technology Data Exchange (ETDEWEB)

J.S. Stuckless; D. O' Leary

2006-09-25

Yucca Mountain has been proposed as the site for the Nation's first geologic repository for high-level radioactive waste. This chapter provides the geologic framework for the Yucca Mountain region. The regional geologic units range in age from late Precambrian through Holocene, and these are described briefly. Yucca Mountain is composed dominantly of pyroclastic units that range in age from 11.4 to 15.2 Ma. The proposed repository would be constructed within the Topopah Spring Tuff, which is the lower of two major zoned and welded ash-flow tuffs within the Paintbrush Group. The two welded tuffs are separated by the partly to nonwelded Pah Canyon Tuff and Yucca Mountain Tuff, which together figure prominently in the hydrology of the unsaturated zone. The Quaternary deposits are primarily alluvial sediments with minor basaltic cinder cones and flows. Both have been studied extensively because of their importance in predicting the long-term performance of the proposed repository. Basaltic volcanism began about 10 Ma and continued as recently as about 80 ka with the eruption of cones and flows at Lathrop Wells, approximately 10 km south-southwest of Yucca Mountain. Geologic structure in the Yucca Mountain region is complex. During the latest Paleozoic and Mesozoic, strong compressional forces caused tight folding and thrust faulting. The present regional setting is one of extension, and normal faulting has been active from the Miocene through to the present. There are three major local tectonic domains: (1) Basin and Range, (2) Walker Lane, and (3) Inyo-Mono. Each domain has an effect on the stability of Yucca Mountain.

Site investigations for repositories for solid radioactive wastes in deep continental geological formations

International Nuclear Information System (INIS)

1982-01-01

This report reviews the earth-science investigations and associated scientific studies that may be needed to select a repository site and confirm that its characteristics are such that it will provide a safe confinement for solidified high-level and alpha-bearing and certain other solid radioactive wastes. Site investigations, as used in this report, cover earth sciences and associated safety analyses. Other site-investigation activities are identified but not otherwise considered here. The repositories under consideration are those consisting of mined cavities in deep continental rocks for accepting wastes in the solid and packaged form. The term deep as used in this report is used solely to emphasize the distinction between the repositories discussed in this report and those for shallow-ground disposal. In general, depths under consideration here are greater than 200 metres. The term continental refers to those geological formations that occur either beneath present-day land masses and adjoining islands or beneath the shallow seas. One of the objectives of site investigations is to collect the site-specific data necessary for the different evaluations, such as modelling required to assess the long-term safety of an underground repository

Site investigations for repositories for solid radioactive wastes in deep continental geological formations

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

This report reviews the earth-science investigations and associated scientific studies that may be needed to select a repository site and confirm that its characteristics are such that it will provide a safe confinement for solidified high-level and alpha-bearing and certain other solid radioactive wastes. Site investigations, as used in this report, cover earth sciences and associated safety analyses. Other site-investigation activities are identified but not otherwise considered here. The repositories under consideration are those consisting of mined cavities in deep continental rocks for accepting wastes in the solid and packaged form. The term deep as used in this report is used solely to emphasize the distinction between the repositories discussed in this report and those for shallow-ground disposal. In general, depths under consideration here are greater than 200 metres. The term continental refers to those geological formations that occur either beneath present-day land masses and adjoining islands or beneath the shallow seas. One of the objectives of site investigations is to collect the site-specific data necessary for the different evaluations, such as modelling required to assess the long-term safety of an underground repository.

Robust record preservation system on geological repository

International Nuclear Information System (INIS)

Ohuchi, J.; Torata, S.; Tsuboya, T.

2004-01-01

Long-term record preservation system on geological disposal of High Level Radioactive Wastes (HLW) has been investigated as the institutional control by RWMC, Japan. Geological disposal of HLW, being based on the passive safe concept, has been considered not to necessitate the human controls to maintain its long-term safety. However how to complement the safety case on geological disposal is an important issue in each countries to progress the repository program with the step-wise decisions process during the long-term period up to several hundreds years. Although we cannot predict the future society, we need to realize the robust and redundant system for preserving records, which should be accessible, retrievable and understandable for the unpredicted future generations. First of all, we held a Rome workshop in January 2003 to exchange views on the matter, resulted in the suggestion directing the discussion on the record management and long-term preservation and retrieval of information regarding radioactive waste. Second, we considered the balance of active and passive system to strengthen the robustness. Another significance of long-term record preservation is to send current generation an implicit message, 'doing our best for future generations', in addition to aiming at both warning and their own decision-making. We call it 'meta-signal' to current generation. Thirdly, we demonstrated the laser-engraving technology to have converted five hundreds pages of an A4 sized report with human readable font sizes to 42 square silicon carbide plates, 10cm x10cm and 1mm in thickness. Silicon carbide would be an alternative to paper and might be possible to be an alternative to microfilm utilized as digital recording media. Another case study is the future generations' accessibility to the preserved records. (author)

DECOVALEX III PROJECT. Mathematical Models of Coupled Thermal-Hydro-Mechanical Processes for Nuclear Waste Repositories. Executive Summary

Energy Technology Data Exchange (ETDEWEB)

Jing, L.; Stephansson, O. [Royal Inst. of Technology, Stockholm (Sweden). Engineering Geology; Tsang, C.F. [Lawrence Berkely National Laboratory, Berkeley, CA (United States). Earth Science Div.; Mayor, J.C. [ENRESA, Madrid (Spain); Kautzky, F. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden)] (eds.)

2005-02-15

DECOVALEX is an international consortium of governmental agencies associated with the disposal of high-level nuclear waste in a number of countries. The consortium's mission is the DEvelopment of COupled models and their VALidation against EXperiments. Hence the acronym/name DECOVALEX. Currently, agencies from Canada, Finland, France, Germany, Japan, Spain, Switzerland, Sweden, United Kingdom, and the United States are in DECOVALEX. Emplacement of nuclear waste in a repository in geologic media causes a number of physical processes to be intensified in the surrounding rock mass due to the decay heat from the waste. The four main processes of concern are thermal, hydrological, mechanical and chemical. Interactions or coupling between these heat-driven processes must be taken into account in modeling the performance of the repository for such modeling to be meaningful and reliable. DECOVALEX III is organized around four tasks. The FEBEX (Full-scale Engineered Barriers EXperiment) in situ experiment being conducted at the Grimsel site in Switzerland is to be simulated and analyzed in Task 1. Task 2, centered around the Drift Scale Test (DST) at Yucca Mountain in Nevada, USA, has several sub-tasks (Task 2A, Task 2B, Task 2C and Task 2D) to investigate a number of the coupled processes in the DST. Task 3 studies three benchmark problems: a) the effects of thermal-hydrologic-mechanical (THM) coupling on the performance of the near-field of a nuclear waste repository (BMT1); b) the effect of upscaling THM processes on the results of performance assessment (BMT2); and c) the effect of glaciation on rock mass behavior (BMT3). Task 4 is on the direct application of THM coupled process modeling in the performance assessment of nuclear waste repositories in geologic media. This executive summary presents the motivation, structure, objectives, approaches, and the highlights of the main achievements and outstanding issues of the tasks studied in the DECOVALEX III project

DECOVALEX III PROJECT. Mathematical Models of Coupled Thermal-Hydro-Mechanical Processes for Nuclear Waste Repositories. Executive Summary

International Nuclear Information System (INIS)

Jing, L.; Stephansson, O.; Kautzky, F.

2005-02-01

DECOVALEX is an international consortium of governmental agencies associated with the disposal of high-level nuclear waste in a number of countries. The consortium's mission is the DEvelopment of COupled models and their VALidation against EXperiments. Hence the acronym/name DECOVALEX. Currently, agencies from Canada, Finland, France, Germany, Japan, Spain, Switzerland, Sweden, United Kingdom, and the United States are in DECOVALEX. Emplacement of nuclear waste in a repository in geologic media causes a number of physical processes to be intensified in the surrounding rock mass due to the decay heat from the waste. The four main processes of concern are thermal, hydrological, mechanical and chemical. Interactions or coupling between these heat-driven processes must be taken into account in modeling the performance of the repository for such modeling to be meaningful and reliable. DECOVALEX III is organized around four tasks. The FEBEX (Full-scale Engineered Barriers EXperiment) in situ experiment being conducted at the Grimsel site in Switzerland is to be simulated and analyzed in Task 1. Task 2, centered around the Drift Scale Test (DST) at Yucca Mountain in Nevada, USA, has several sub-tasks (Task 2A, Task 2B, Task 2C and Task 2D) to investigate a number of the coupled processes in the DST. Task 3 studies three benchmark problems: a) the effects of thermal-hydrologic-mechanical (THM) coupling on the performance of the near-field of a nuclear waste repository (BMT1); b) the effect of upscaling THM processes on the results of performance assessment (BMT2); and c) the effect of glaciation on rock mass behavior (BMT3). Task 4 is on the direct application of THM coupled process modeling in the performance assessment of nuclear waste repositories in geologic media. This executive summary presents the motivation, structure, objectives, approaches, and the highlights of the main achievements and outstanding issues of the tasks studied in the DECOVALEX III project. The

Generic description of facilities at the shaft head (auxiliary entrance installations) of deep geological repositories; Generische Beschreibung von Schachtkopfanlagen (Nebenzugangsanlagen) geologischer Tiefenlager

Energy Technology Data Exchange (ETDEWEB)

NONE

2016-10-15

this report, NAGRA assumes that the auxiliary access facilities of a deep geological repository can be realised in compliance with prescribed norms and standards and operated safely. The actual locations of these facilities will be concretised in a later project phase, with the concerns and wishes of the affected region being taken into consideration within certain boundary conditions. (authors)

Proposal for the classification of scenarios for deep geological repositories in probability classes

International Nuclear Information System (INIS)

Beuth, Thomas

2013-03-01

The provided report was elaborated in the framework of the project 3609R03210 ''Research and Development for Proof of the long-term Safety of Deep Geological Repositories''. It contains a proposal for a methodology that enables the assignment of developed scenarios in the frame of Safety Cases to defined probability classes. The assignment takes place indirectly through the categorization of the defining relevant factors (so-called FEP: Features, Events and Processes) of the respective scenarios also in probability classes. Therefore, decision trees and criteria were developed for the categorization of relevant factors in classes. Besides the description of the methodology another focal point of the work was the application of the method taking into account a defined scenario. By means of the scenario the different steps of the method and the decision criteria were documented, respectively. In addition, potential subjective influences along the path of decisions regarding the assignment of scenarios in probability classes were identified.

Finite element code FENIA verification and application for 3D modelling of thermal state of radioactive waste deep geological repository

Science.gov (United States)

Butov, R. A.; Drobyshevsky, N. I.; Moiseenko, E. V.; Tokarev, U. N.

2017-11-01

The verification of the FENIA finite element code on some problems and an example of its application are presented in the paper. The code is being developing for 3D modelling of thermal, mechanical and hydrodynamical (THM) problems related to the functioning of deep geological repositories. Verification of the code for two analytical problems has been performed. The first one is point heat source with exponential heat decrease, the second one - linear heat source with similar behavior. Analytical solutions have been obtained by the authors. The problems have been chosen because they reflect the processes influencing the thermal state of deep geological repository of radioactive waste. Verification was performed for several meshes with different resolution. Good convergence between analytical and numerical solutions was achieved. The application of the FENIA code is illustrated by 3D modelling of thermal state of a prototypic deep geological repository of radioactive waste. The repository is designed for disposal of radioactive waste in a rock at depth of several hundred meters with no intention of later retrieval. Vitrified radioactive waste is placed in the containers, which are placed in vertical boreholes. The residual decay heat of radioactive waste leads to containers, engineered safety barriers and host rock heating. Maximum temperatures and corresponding times of their establishment have been determined.

NF-PRO research on a repository for vitrified waste and spent fuel

International Nuclear Information System (INIS)

Sneyers, A.

2006-01-01

NF-PRO is a four-year (2004-2007) Integrated Project supported by funding under the Sixth Research (EURATOM) Programme of the European Commission. NF-PRO is coordinated by SCK C EN and investigates key processes in the near-field of geological repositories for the disposal of high-level vitrified waste and spent nuclear fuel. The near-field of a geological repository consists of the area surrounding the waste packages and is composed of several engineered barriers that enclose and confine the disposed waste. These barriers include the waste form, the waste canisters, backfills, seals, plugs and the part of the host rock that has been modified by the excavation of the repository. In all repository designs under investigation within EU Member States, the near-field plays an important role in ensuring the overall safety of disposal: its principal function is to retain radionuclides over extended periods of time and to minimise their release from the waste to the host rock. The main objective of NF-PRO is to integrate European research on the near field with the aim of enhancing common understanding of the long-term changes taking place in a deep repository. NF-PRO assesses how these changes affect the containment of the disposed radioactive waste. Knowledge generated by the project can be applied in waste management programmes to optimise repository designs and to make barriers functional and resource-efficient. The integration of results from detailed process studies in assessments on the overall near-field system performance is a key objective of NF-PRO. The level of integration envisaged by NF-PRO has not yet been achieved in earlier research projects supported by the European Commission. Accordingly, NF PRO represents a major step forward in the establishing of the scientific and technical basis for geological disposal and the safe management of radioactive wastes

Strategic management of HLW repository projects

International Nuclear Information System (INIS)

Bartlett, J.W.

1984-01-01

This paper suggests an approach to strategic management of HLW repository projects based on the premise that a primary objective of project activities is resolution of issues. The approach would be implemented by establishing an issues management function with responsibility to define the issues agenda, develop and apply the tools for assessing progress toward issue resolution, and develop the issue resolution criteria. A principal merit of the approach is that it provides a defensible rationale for project plans and activities. It also helps avoid unnecessary costs and schedule delays, and it helps assure coordination between project functions that share responsibilities for issue resolution

Staff technical position on investigations to identify fault displacement hazards and seismic hazards at a geologic repository

International Nuclear Information System (INIS)

McConnell, K.I.; Blackford, M.E.; Ibrahim, A.K.

1992-07-01

The purpose of this Staff Technical Position (STP) is to provide guidance to the US Department of Energy (DOE) on acceptable geologic repository investigations that can be used to identify fault displacement hazards and seismic hazards. ne staff considers that the approach this STP takes to investigations of fault displacement and seismic phenomena is appropriate for the collection of sufficient data for input to analyses of fault displacement hazards and seismic hazards, both for the preclosure and postclosure performance periods. However, detailed analyses of fault displacement and seismic data, such as those required for comprehensive assessments of repository performance, may identify the need for additional investigations. Section 2.0 of this STP describes the 10 CFR Part 60 requirements that form the basis for investigations to describe fault displacement hazards and seismic hazards at a geologic repository. Technical position statements and corresponding discussions are presented in Sections 3.0 and 4.0, respectively. Technical position topics in this STP are categorized thusly: (1) investigation considerations, (2) investigations for fault-displacement hazards, and (3) investigations for seismic hazards

Methodology for the development of scenarios for the evaluation of the behaviour of a deep geological repository for high-level radioactive waste in a granite formation

International Nuclear Information System (INIS)

Cortes Martin, A.; Alonso, J.; Gonzalez, E.

1996-01-01

In time, deep geological repositories for radioactive waste undergo significant environmental changes caused either by natural processes or by human actions. In view of a long-term safety analysis, it is fundamental to identify all the possible evolutions of the system. This process is denominated scenario development. This paper deals with the methodology used to generate scenarios within the framework of the AGP (Deep Geological Repository) project for assessing behaviour in granite medium. It begins with a brief description of the methodology used to identify the relevant factors for the safety analysis on the system. It then presents the details of the actual scenario-generating methodology which consists of dividing the entire system into barrier states or subsystems a graphic procedure by means of which the factors are represented in relation to their predictable impact or extent of their effect on the subsystems. This methodology is a good tool for displaying and grouping the most significant scenarios for the subsequent analysis of consequences. (Author)

Salt Repository Project transportation system interface requirements: Transportation system/repository receiving facility interface requirements

International Nuclear Information System (INIS)

Smith, L.A.; Insalaco, J.W.; Trainer, T.A.

1988-01-01

This report is a preliminary review of the interface between the transportation system and the repository receiving facility for a nuclear waste mined geologic disposal system in salt. Criteria for generic cask and facility designs are developed. These criteria are derived by examining the interfaces that occur as a result of the operations needed to receive nuclear waste at a repository. These criteria provide the basis for design of a safe, operable, practical nuclear waste receiving facility. The processing functions required to move the shipping unit from the gate into the unloading area and back to the gate for dispatch are described. Criteria for a generic receiving facility are discussed but no specific facility design is presented or evaluated. The criteria are stated in general terms to allow application to a wide variety of cask and facility designs. 9 refs., 6 figs., 4 tabs

Siting, design and construction of a deep geological repository for the disposal of high level and alpha bearing wastes

International Nuclear Information System (INIS)

1990-06-01

The main objective of this document is to summarize the basic principles and approaches to siting, design and construction of a deep geological repository for disposal of high level and alpha bearing radioactive wastes, as commonly agreed upon by Member States. This report is addressed to decision makers and technical managers as well as to specialists planning for siting, design and construction of geological repositories for disposal of high level and alpha bearing wastes. This document is intended to provide Member States of the IAEA with a summary outline for the responsible implementing organizations to use for siting, designing and constructing confinement systems for high level and alpha bearing radioactive waste in accordance with the protection objectives set by national regulating authorities or derived from safety fundamentals and standards of the IAEA. The protection objectives will be achieved by the isolation of the radionuclides from the environment by a repository system, which consists of a series of man made and natural safety barriers. Engineered barriers are used to enhance natural geological containment in a variety of ways. They must complement the natural barriers to provide adequate safety and necessary redundancy to the barrier system to ensure that safety standards are met. Because of the long timescales involved and the important role of the natural barrier formed by the host rock, the site selection process is a key activity in the repository design and development programme. The choice of the site, the investigation of its geological setting, the exploration of the regional hydrogeological setting and the primary underground excavations are all considered to be part of the siting process. 16 refs

Thermodynamic stability of actinide pyrochlore minerals in deep geologic repository environments

International Nuclear Information System (INIS)

Wang, YIFENG; Xu, HUIFANG

2000-01-01

Crystalline phases of pyrochlore (e.g., CaPuTi 2 O 7 , CaUTi 2 O 7 ) have been proposed as a durable ceramic waste form for disposal of high level radioactive wastes including surplus weapons-usable plutonium. In this paper, the authors use a linear free energy relationship to predict the Gibbs free energies of formation of pyrochlore phases (CaMTi 2 O 7 ). The Pu-pyrochlore phase is predicted to be stable with respect to PuO 2 , CaTiO 3 , and TiO 2 at room temperatures. Pu-pyrochlore is expected to be stable in a geologic repository where silica and carbonate components are absent or limited. The authors suggest that a repository in a salt formation be an ideal environment for disposal of high level, pyrochlore-based ceramic wastes. In such environment, adding CaO as a backfill will make pyrochlore minerals thermodynamically stable and therefore effectively prevent actinide release from these mineral phases

Iterative performance assessments as a regulatory tool for evaluating repository safety: How experiences from SKI Project-90 were used in formulating the new performance assessment project SITE-94

International Nuclear Information System (INIS)

Andersson, J.

1993-01-01

The Swedish Nuclear Power Inspectorate, SKI, regulatory research program has to prepare for the process of licensing a repository for spent nuclear fuel, by building up the necessary knowledge and review capacity. SKIs main strategy for meeting this demand is to develop an independent performance assessment capability. SKIs first own performance assessment project, Project-90, was completed in 1991 and is now followed by a new project, SITE-94. SITE-94 is based on conclusions reached within Project-90. An independent review of Project-90, carried out by a NEA team of experts, has also contributed to the formation of the project. Another important reason for the project is that the implementing organization in Sweden, SKB, has proposed to submit an application to start detailed investigation of a repository candidate site around 1997. SITE-94 is a performance assessment of a hypothetical repository at a real site. The main objective of the project is to determine how site specific data should be assimilated into the performance assessment process, and to evaluate how uncertainties inherent in site characterization will influence performance assessment results. This will be addressed by exploring multiple interpretations, conceptual models, and parameters consistent with the site data. The site evaluation will strive for consistency between geological, hydrological, rock mechanical, and geochemical descriptions. Other important elements of SITE-94 are the development of a practical and defensible methodology for defining, constructing and analyzing scenarios, the development of approaches for treatment of uncertainties, evaluation of canister integrity, and the development and application of an appropriate quality assurance plan for performance assessments

Handling encapsulated spent fuel in a geologic repository environment

International Nuclear Information System (INIS)

Ballou, L.B.

1983-02-01

In support of the Spent Fuel Test-Climate at the U.S. Department of Energy's Nevada Test Site, a spent-fuel canister handling system has been designed, deployed, and operated successfully during the past five years. This system transports encapsulated commercial spent-fuel assemblies between the packaging facility and the test site (approx. 100 km), transfers the canisters 420 m vertically to and from a geologic storage drift, and emplaces or retrieves the canisters from the storage holes in the floor of the drift. The spent-fuel canisters are maintained in a fully shielded configuration at all times during the handling cycle, permitting manned access at any time for response to any abnormal conditions. All normal operations are conducted by remote control, thus assuring as low as reasonably achievable exposures to operators; specifically, we have had no measurable exposure during 30 canister transfer operations. While not intended to be prototypical of repository handling operations, the system embodies a number of concepts, now demonstrated to be safe, reliable, and economical, which may be very useful in evaluating full-scale repository handling alternatives in the future. Among the potentially significant concepts are: Use of an integral shielding plug to minimize radiation streaming at all transfer interfaces. Hydraulically actuated transfer cask jacking and rotation features to reduce excavation headroom requirements. Use of a dedicated small diameter (0.5 m) drilled shaft for transfer between the surface and repository workings. A wire-line hoisting system with positive emergency braking device which travels with the load. Remotely activated grapples - three used in the system - which are insensitive to load orientation. Rail-mounted underground transfer vehicle operated with no personnel underground

Status of the safety concept and safety demonstration for an HLW repository in salt. Summary report

Energy Technology Data Exchange (ETDEWEB)

Bollingerfehr, W.; Buhmann, D.; Filbert, W.; and others

2013-12-15

Salt formations have been the preferred option as host rocks for the disposal of high level radioactive waste in Germany for more than 40 years. During this period comprehensive geological investigations have been carried out together with a broad spectrum of concept and safety related R and D work. The behaviour of an HLW repository in salt formations, particularly in salt domes, has been analysed in terms of assessment of the total system performance. This was first carried out for concepts of generic waste repositories in salt and, since 1998, for a repository concept with specific boundary conditions, taking the geology of the Gorleben salt dome as an example. Suitable repository concepts and designs were developed, the technical feasibility has been proven and operational and long-term safety evaluated. Numerical modelling is an important input into the development of a comprehensive safety case for a waste repository. Significant progress in the development of numerical tools and their application for long-term safety assessment has been made in the last two decades. An integrated approach has been used in which the repository concept and relevant scientific and engineering data are combined with the results from iterative safety assessments to increase the clarity and the traceability of the evaluation. A safety concept that takes full credit of the favourable properties of salt formations was developed in the course of the R and D project ISIBEL, which started in 2005. This concept is based on the safe containment of radioactive waste in a specific part of the host rock formation, termed the containment providing rock zone, which comprises the geological barrier, the geotechnical barriers and the compacted backfill. The future evolution of the repository system will be analysed using a catalogue of Features, Events and Processes (FEP), scenario development and numerical analysis, all of which are adapted to suit the safety concept. Key elements of the

Source-book of International Activities Related to the Development of Safety Cases for Deep Geological Repositories

International Nuclear Information System (INIS)

2017-01-01

All national radioactive waste management authorities recognise today that a robust safety case is essential in developing disposal facilities for radioactive waste. To improve the robustness of the safety case for the development of a deep geological repository, a wide variety of activities have been carried out by national programs and international organisations over the past years. The Nuclear Energy Agency, since first introducing the modern concept of the 'safety case', has continued to monitor major developments in safety case activities at the international level. This Source-book summarises the activities being undertaken by the Nuclear Energy Agency, the European Commission and the International Atomic Energy Agency concerning the safety case for the operational and post-closure phases of geological repositories for radioactive waste that ranges from low-level to high-level waste and for spent fuel. In doing so, it highlights important differences in focus among the three organisations

A Socio-Technical Perspective on Repository Monitoring - 12229

Energy Technology Data Exchange (ETDEWEB)

Bergmans, Anne [University of Antwerp, Faculty of Political and Social Sciences, Sint-Jacobstraat 2, 2000 Antwerpen (Belgium); Elam, Mark; Sundqvist, Goeran [University of Gothenburg, Department of Sociology, Box 720, 40530 Gothenburg (Sweden); Simmons, Peter [University of East Anglia, School of Environmental Sciences, Norwich NR4 7TJ (United Kingdom)

2012-07-01

Monitoring geological repositories for high-activity radioactive wastes has both technical and social dimensions, which are closely interrelated. To investigate the implications of this for geological disposal, data on experts' expectations of repository monitoring and the functions that it is expected to serve were analysed. The analysis drew on strategic and technical documents on monitoring produced by national agencies and by international organisations or projects; interviews with specialists in radioactive waste management organisations on monitoring and on their perceptions of societal concerns and expectations; and observations from technical workshops on repository monitoring. Three main rationales for monitoring were found: performance confirmation; decision support in a step-wise process; and public and stakeholder confidence building. The expectation that monitoring will enhance public confidence is then examined from a social scientific perspective and the potential for and challenges to using monitoring in this way are reviewed. In conclusion, implications for stakeholder engagement in the development of monitoring objectives and strategies are discussed. (authors)

A web-based repository of surgical simulator projects.

Science.gov (United States)

Leskovský, Peter; Harders, Matthias; Székely, Gábor

2006-01-01

The use of computer-based surgical simulators for training of prospective surgeons has been a topic of research for more than a decade. As a result, a large number of academic projects have been carried out, and a growing number of commercial products are available on the market. Keeping track of all these endeavors for established groups as well as for newly started projects can be quite arduous. Gathering information on existing methods, already traveled research paths, and problems encountered is a time consuming task. To alleviate this situation, we have established a modifiable online repository of existing projects. It contains detailed information about a large number of simulator projects gathered from web pages, papers and personal communication. The database is modifiable (with password protected sections) and also allows for a simple statistical analysis of the collected data. For further information, the surgical repository web page can be found at www.virtualsurgery.vision.ee.ethz.ch.

Groundwater movements around a repository. Geological and geotechnical conditions

International Nuclear Information System (INIS)

Stille, H.; Burgess, A.; Lindblom, U.E.

1977-09-01

The report was prepared as one of a series of technical reports within a study of the groundwater movements around a repository for radioactive waste in the Precambrian bedrock of Sweden. This assessment is intended to provide basic geotechnical data for the analysis. These data include properties and conditions that are representative of the intact rock, the rock mass in general, and the groundwater regime. As there exist a considerable range in the mineralogy of potentially suitable plutonic rocks and since a specific site has not yet been selected, all of the parameters presented in this report must be based on presumptive geological and hydrogeological conditions. Where possible, data for two potential site areas, namely Oskarshamn and Forsmark, are presented. This report is divided into four parts. First, a brief description of the procedure for modelling groundwater movements is presented, along with a tabulation of the important parameters. Secondly, a description of the geological and hydrogeological conditions of the Fennoscandian shield, as well as of the two general site areas, is given. The final two sections of the report provide thermomechanical and geohydrological characteristics and properties of the host rock

The importance of the retrievability of nuclear waste for the implementation of safeguard regimes for geologic repositories

International Nuclear Information System (INIS)

Swahn, J.A.

1999-01-01

To find acceptance for the construction and siting of spent fuel repositories retrievability of the spent fuel is a desired feature. In order to minimize the levels of safeguards needed for the plutonium in spent fuel repositories the retrievability should be as low as possible. These contradictory goals have be balanced against each other during the operational phase, before closure and after closure of the repository. Arguments can be made for having the spent fuel in a highly-retrievable state during the operational phase, in a semi-retrievable state at the end of the operational phase but before closure and in a low-retrievable state after closure. The spent fuel in a mined geologic repository will never be able to be considered irretrievable and surveillance of the repository will be needed for an extended time after closure. The level of safeguards needed will depend on the local, regional and global societal conditions for several hundred thousand years into the future. (author)

Confidence in the long-term safety of deep geological repositories. Its development and communication

International Nuclear Information System (INIS)

1999-01-01

The technical aspects of confidence have been the subject of considerable debate, especially the concept of model validation. The safety case that is provided at a particular stage in the planning, construction, operation or closure of a deep geological repository is a part of a broader decision basis that guides the repository-development process. The basic steps for deriving the safety case at various stages of repository development involve: a safety assessment; and the documentation of the safety assessment, a statement of confidence in the safety indicated by the assessment, and the confirmation of the appropriateness of the safety strategy. The approaches to establish confidence in the evaluation of safety should aim to ensure that the decisions taken within the incremental process of repository development are well-founded. Various aspects of confidence in the evaluation of safety, and their integration within a safety case, are presented in detail in the present report. When communicating confidence in the findings of a safety assessment, clarity in the communication of concepts is always required. Consistent with this requirement, key concepts are specifically defined in the main text of the report. (R.P.)

Salt Repository Project shaft design guide: Revision 0

International Nuclear Information System (INIS)

1987-12-01

The Salt Repository Project (SRP) Shaft Design Guide (SDG) and the accompanying SRP Input to Seismic Design define the basic approach for developing appropriate shaft designs for a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. The SDG is based on current mining industry standards and practices enhanced to meet the special needs of an underground nuclear waste repository. It provides a common approach for design of both the exploratory and repository shafts. The SDG defines shaft lining and material concepts and presents methods for calculating the loads and displacements that will be imposed on lining structures. It also presents the methodology and formulae for sizing lining components. The SDG directs the shaft designer to sources of geoscience and seismic design data for the Deaf Smith County, Texas repository site. In addition, the SDG describes methods for confirming shaft lining design by means of computer analysis, and it discusses performance monitoring needs that must be considered in the design. 113 refs., 18 figs., 14 tabs

Development of geological disposal system; localization of element cost data and cost evaluation on the HLW repository

Energy Technology Data Exchange (ETDEWEB)

Lee, Byung Sik; Kim, Kil Jung; Yang, Young Jin; Kim, Sung Chun [KOPEC, Taejeon (Korea)

2002-03-01

To estimate Total Life Cycle Cost (TSLCC) for Korea HLW Repository through localization of element cost data, we review and re-organize each basic element cost data for reference repository system, localize various element cost and finally estimate TSLCC considering economic parameters. As results of the study, TSLCC is estimated as 17,167,689 million won, which includes costs for site preparation, surface facilities, underground facilities and management/integration. Since HLW repository Project is an early stage of pre-conceptual design at present, the information of design and project information are not enough to perform cost estimate and cost localization for the Project. However, project cost structure is re-organized based on the local condition and Total System Life Cycle Cost is estimated using the previous cost data gathered from construction experience of the local nuclear power plant. Project results can be used as basic reference data to assume total construction cost for the local HLW repository and should be revised to more reliable cost data with incorporating detail project design information into the cost estimate in a future. 20 refs. (Author)

Andra's geologic repository monitoring strategy

International Nuclear Information System (INIS)

Buschaert, S.; Lesoille, S.; Bertrand, J.; Landais, P.

2012-01-01

Document available in extended abstract form only. After having concluded a feasibility study of deep geological disposal for high-level and long-lived radioactive waste in 2005, Andra was charged by the Planning Act no. 2006-739 to design and create an industrial site for geological disposal called Cigeo which must be reversible for at least a century-long period. The French Safety Guide recommends that Andra develop a monitoring program to be implemented at repository construction and conducted until closure, and possibly after closure, with the aim to confirming prior expectations and enhancing knowledge of relevant processes. This abstract focuses on underground structure monitoring. The monitoring system is based on a combination of in-situ instrumentation and nondestructive methods to obtain the required level of reliable performance. To optimize the device distribution, we take into account both the repetitive design of disposal cells and the homogeneity of the rock properties. This resulted in distinguishing pilot disposal cells that are highly instrumented and standard disposal cells where the instrumentation density could be reduced; monitoring will rely mostly on robotic nondestructive evaluations. If monitoring technologies do not comply with all monitoring objectives, real withdrawal tests of high level wastes in some pilot disposal cells are also planned to provide the possibility of carrying out visual inspection, destructive analyses and samplings on construction materials. Such cells are planned to be dismantled because of the potential disturbance of their component performances from the testing process. Based on this overall strategy, Andra has analyzed the technical requirements that must be met by its monitoring equipment. First, these must be able to provide information on key THMCR (Thermal- Hydraulic-Mechanical-Chemical and Radiological) processes, to provide a three-dimensional image of a disposal component's behavior and thus to understand

Characterizing the proposed geologic repository for high-level radioactive waste at Yucca Mountain, Nevada: hydrology and geochemistry

Science.gov (United States)

Stuckless, John S.; Levich, Robert A.

2012-01-01

This hydrology and geochemistry volume is a companion volume to the 2007 Geological Society of America Memoir 199, The Geology and Climatology of Yucca Mountain and Vicinity, Southern Nevada and California, edited by Stuckless and Levich. The work in both volumes was originally reported in the U.S. Department of Energy regulatory document Yucca Mountain Site Description, for the site characterization study of Yucca Mountain, Nevada, as the proposed U.S. geologic repository for high-level radioactive waste. The selection of Yucca Mountain resulted from a nationwide search and numerous committee studies during a period of more than 40 yr. The waste, largely from commercial nuclear power reactors and the government's nuclear weapons programs, is characterized by intense penetrating radiation and high heat production, and, therefore, it must be isolated from the biosphere for tens of thousands of years. The extensive, unique, and often innovative geoscience investigations conducted at Yucca Mountain for more than 20 yr make it one of the most thoroughly studied geologic features on Earth. The results of these investigations contribute extensive knowledge to the hydrologic and geochemical aspects of radioactive waste disposal in the unsaturated zone. The science, analyses, and interpretations are important not only to Yucca Mountain, but also to the assessment of other sites or alternative processes that may be considered for waste disposal in the future. Groundwater conditions, processes, and geochemistry, especially in combination with the heat from radionuclide decay, are integral to the ability of a repository to isolate waste. Hydrology and geochemistry are discussed here in chapters on unsaturated zone hydrology, saturated zone hydrology, paleohydrology, hydrochemistry, radionuclide transport, and thermally driven coupled processes affecting long-term waste isolation. This introductory chapter reviews some of the reasons for choosing to study Yucca Mountain as a

Characterizing the proposed geologic repository for high-level radioactive waste at Yucca Mountain, Nevada--hydrology and geochemistry

Science.gov (United States)

Stuckless, John S.; Levich, Robert A.

2012-01-01

This hydrology and geochemistry volume is a companion volume to the 2007 Geological Society of America Memoir 199, The Geology and Climatology of Yucca Mountain and Vicinity, Southern Nevada and California, edited by Stuckless and Levich. The work in both volumes was originally reported in the U.S. Department of Energy regulatory document Yucca Mountain Site Description, for the site characterization study of Yucca Mountain, Nevada, as the proposed U.S. geologic repository for high-level radioactive waste. The selection of Yucca Mountain resulted from a nationwide search and numerous committee studies during a period of more than 40 yr. The waste, largely from commercial nuclear power reactors and the government's nuclear weapons programs, is characterized by intense penetrating radiation and high heat production, and, therefore, it must be isolated from the biosphere for tens of thousands of years. The extensive, unique, and often innovative geoscience investigations conducted at Yucca Mountain for more than 20 yr make it one of the most thoroughly studied geologic features on Earth. The results of these investigations contribute extensive knowledge to the hydrologic and geochemical aspects of radioactive waste disposal in the unsaturated zone. The science, analyses, and interpretations are important not only to Yucca Mountain, but also to the assessment of other sites or alternative processes that may be considered for waste disposal in the future. Groundwater conditions, processes, and geochemistry, especially in combination with the heat from radionuclide decay, are integral to the ability of a repository to isolate waste. Hydrology and geochemistry are discussed here in chapters on unsaturated zone hydrology, saturated zone hydrology, paleohydrology, hydrochemistry, radionuclide transport, and thermally driven coupled processes affecting long-term waste isolation. This introductory chapter reviews some of the reasons for choosing to study Yucca Mountain as a

Preclosure Seismic Design Methodology for a Geologic Repository at Yucca Mountain

International Nuclear Information System (INIS)

K. Coppersmith

2004-01-01

This topical report describes the methodology and criteria that the U.S. Department of Energy (DOE) intends to use for preclosure seismic design of structures, systems, and components (SSCs) that are important to safety (ITS) in the geologic repository operations area. 10 Code of Federal Regulations (CFR) Part 63 [DIRS 156605], states that for a license to be issued for operation of a high-level radioactive waste repository, the U.S. Nuclear Regulatory Commission (NRC) must find that the facility will not constitute an unreasonable risk to the health and safety of the public (Section 63.41[c] [DIRS 156605]). Section 63.21(c)(5) [DIRS 156605] requires that a preclosure safety analysis (PCSA) be performed to ensure that the preclosure performance objectives (Section 63.111 [DIRS 156605]) have been met. The PCSA is a systematic examination of the site, the design, and the potential hazards (Section 63.102[f] [DIRS 156605]), including a comprehensive identification of potential event sequences. Potential naturally-occurring hazards include those event sequences that are initiated by earthquake ground motions or fault displacements due to earthquakes

Modelling of gas generation in deep geological repositories after closure

International Nuclear Information System (INIS)

Poller, A.; Mayer, G.; Darcis M; Smith, P.

2016-12-01

In deep geological repositories for radioactive waste, significant quantities of gases will be generated in the long term as a result of various processes, notably the anaerobic corrosion of metals and the degradation of organic materials. Therefore, the impact of gas production on post-closure safety of the repositories needs to be assessed as part of a safety case. The present report provides a comprehensive description of the quantitative modelling of gas generation and associated water consumption during the post-closure phase of deep geological repositories in Opalinus Clay based on current scientific knowledge and on current preliminary repository designs. This includes a presentation of the modelling basis, namely the conceptual and mathematical models, the input data used, the computer tools developed, the relevant uncertainties and principal programme / design options, as well as the derivation, analysis and discussion of specific assessment cases. The modelling is carried out separately for the two main sources of gas, which are the emplaced waste including the disposal containers; and the construction materials. The contribution of construction materials to gas generation rates in emplacement tunnels for spent fuel (SF) and vitrified high-level waste (HLW) is significant during several thousand years after closure. In the long term, however, the corrosion of the disposal canisters, which are in the reference case assumed to be fabricated of carbon steel, accounts for the vast majority of the total gas produced in these tunnels. The contribution of construction materials in emplacement caverns for long lived intermediate-level waste (ILW) and low- and intermediate-level waste (L/ILW) to gas generation is generally small. In ILW emplacement caverns, gas generation is generally dominated by hydrogen generation from the corrosion of cast iron Mosaik-II waste containers for PWR internals and from the corrosion of aluminium in operational waste from the

Modelling of gas generation in deep geological repositories after closure

Energy Technology Data Exchange (ETDEWEB)

Poller, A. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Mayer, G.; Darcis M [AF-Consult Switzerland Ltd, Baden-Dättwil, (Switzerland); Smith, P. [Safety Assessment Management Ltd, Henley-On-Thames, Oxfordshire (United Kingdom)

2016-12-15

In deep geological repositories for radioactive waste, significant quantities of gases will be generated in the long term as a result of various processes, notably the anaerobic corrosion of metals and the degradation of organic materials. Therefore, the impact of gas production on post-closure safety of the repositories needs to be assessed as part of a safety case. The present report provides a comprehensive description of the quantitative modelling of gas generation and associated water consumption during the post-closure phase of deep geological repositories in Opalinus Clay based on current scientific knowledge and on current preliminary repository designs. This includes a presentation of the modelling basis, namely the conceptual and mathematical models, the input data used, the computer tools developed, the relevant uncertainties and principal programme / design options, as well as the derivation, analysis and discussion of specific assessment cases. The modelling is carried out separately for the two main sources of gas, which are the emplaced waste including the disposal containers; and the construction materials. The contribution of construction materials to gas generation rates in emplacement tunnels for spent fuel (SF) and vitrified high-level waste (HLW) is significant during several thousand years after closure. In the long term, however, the corrosion of the disposal canisters, which are in the reference case assumed to be fabricated of carbon steel, accounts for the vast majority of the total gas produced in these tunnels. The contribution of construction materials in emplacement caverns for long lived intermediate-level waste (ILW) and low- and intermediate-level waste (L/ILW) to gas generation is generally small. In ILW emplacement caverns, gas generation is generally dominated by hydrogen generation from the corrosion of cast iron Mosaik-II waste containers for PWR internals and from the corrosion of aluminium in operational waste from the

Effects of gas overpressurisation on the geological environment of a deep repository

International Nuclear Information System (INIS)

Nash, P.J.; Rodwell, W.R.

1990-04-01

The effect of gas generated from the deep burial of low and intermediate level radioactive wastes is being assessed. Significant volumes of gas are expected to be produced by anaerobic corrosion of metals and microbial degradation of organic materials. Work is being carried out to determine how easily the gas generated can move away from the repository, since if its flow were impeded the pressure in the repository would rise. If the flow were sufficiently impeded then the pressure rise could ultimately lead to fracturing of the vault or the flow field environment, possibly providing pathways that could accelerate the movement of radionuclides to the surface. This study considers the effects of such an overpressurisation on the integrity of the geological environment containing the repository. It attempts to quantify the pore fluid pressures at which fracturing of hard rock masses may occur by investigating a number of models of rock failure in homogeneously stressed rock and the effects of the presence of an idealised vault on the stress field. A crack opening model has also been developed which considers the effect of the overpressurisation on the dimensions of existing cracks within the rock and hence on the value of its permeability. (Author)

The application of nuclear geophysics method to evaluate the geological environment of nuclear waste repository

International Nuclear Information System (INIS)

Fang, Fang; Xiaoqin, Wang; Kuanliang, Li; Xinsheng, Hou; Jingliang, Zhu; Binxin, Hu

2002-01-01

'Cleanly land should be given back ground.' This is a task while nuclear engineering have to be retired. We applied the nuclear geophysics methods and combined with geology, hydrology, geochemistry, and other methods, to evaluate the environment of nuclear waste repository. It is the important work to renovate environment and prepare technology before ex-service of the nuclear engineering

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 16. Repository preconceptual design studies: BPNL waste forms in salt

International Nuclear Information System (INIS)

1978-04-01

This volume, Volume 16, ''Repository Preconceptual Design Studies: BPNL Waste Forms in Salt,'' is one of a 23 volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provide a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This document describes a preconceptual design for a nuclear waste storage facility in salt. The waste forms assumed to arrive at the repository were supplied by Battelle Pacific Northwest Laboratories (BPNL). The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/17, ''Drawings for Repository Preconceptual Design Studies: BPNL Waste Forms in Salt.''

Geologic disposal evaluation program semiannaul report for period ending March 31, 1975

International Nuclear Information System (INIS)

1975-07-01

The Radioactive Waste Repository Project at the Oak Ridge National Laboratory has for some time been engaged in a program directed toward establishing a Federal Repository for radioactive wastes, primarily solidified high-level waste, in a bedded salt formation. Early in 1974, the project was restructured and, to more nearly reflect its broadened scope, was renamed the Geologic Disposal Evaluation (GDE) Program. This report is the first in a series of semiannual progress reports which will be issued to document the progress made in the GDE Program. Most of the subject matter discussed is either geologic or developmental in nature, as would be expected, since the engineering assessment depends on the data generated in these two areas. In addition, since this report also covers the transition period between the Radioactive Waste Repository Project (RWRP) and the GDE Program, information on several RWRP programs, is included. (U.S.)

The ESDRED project: Engineering studies and demonstration of repository designs

International Nuclear Information System (INIS)

Verstricht, J.

2009-01-01

The construction, operation and closure of a deep geological repository for spent fuel and long-lived radioactive waste in clay involves specific technologies. The demonstration of these techniques at an industrial scale is being carried out in the frame of a technological integrated project within the sixth Framework Programme of EURATOM. The Belgian design for high level waste disposal is based on the so-called Supercontainer concept. Within this concept, the waste is encased in a carbon steel overpack, which is consequently fitted into a 70 cm thick concrete shell, in its turn enveloped by a stainless steel liner. A Supercontainer measures about 2 m in diameter. In the design of the repository, the Supercontainers will be emplaced, one after the other, in disposal galleries. The space between the Supercontainers and the gallery lining needs to be filled up with a solid material. The most essential function of this component, referred to as backfill, is to prevent a collapse of the gallery. A secondary function is to limit the presence of free oxygen, to limit corrosion. In the ESDRED project EIG EURIDICE, together with SCK-CEN and ONDRAF/NIRAS, investigates technologies to apply the backfill. After testing two techniques to apply the backfill in 2007 at limited scale (unite with granular material and grouting with backfill mortar), grouting was selected as the preferred technique. This technique then should be tested at full-scale (30 m long mock-up). First, a full-scale structure needs to built, including an extensive instrumentation programme. In addition, the logistical needs to ensure a continuous backfill operation have to be worked out. The objective is to have the almost 100 m 3 backfilled in 4 hours

Alternative measure for performance of HLW geologic repository

International Nuclear Information System (INIS)

Joonhang, Ahn; Chambre, P.L.

2001-01-01

A repository performance model that can show effects of canister multiplicity and repository configuration has been developed. Masses of a radionuclide in the repository and in the far field are proposed as performance measures. Canister multiplicity has significant effects on the release of long-lived radionuclides from the repository. As more canisters are included in the same water stream, the radionuclide concentration in the stream increases, but becomes independent of the number of canisters for sufficiently many canisters. Effects of reduction of radionuclide mass in the repository on the repository performance are clearly observed if the canister multiplicity is taken into account and the mass-based measures are applied. (author)

Vitrification treatment options for disposal of greater-than-Class-C low-level waste in a deep geologic repository

International Nuclear Information System (INIS)

Fullmer, K.S.; Fish, L.W.; Fischer, D.K.

1994-11-01

The Department of Energy (DOE), in keeping with their responsibility under Public Law 99-240, the Low-Level Radioactive Waste Policy Amendments Act of 1985, is investigating several disposal options for greater-than-Class C low-level waste (GTCC LLW), including emplacement in a deep geologic repository. At the present time vitrification, namely borosilicate glass, is the standard waste form assumed for high-level waste accepted into the Civilian Radioactive Waste Management System. This report supports DOE's investigation of the deep geologic disposal option by comparing the vitrification treatments that are able to convert those GTCC LLWs that are inherently migratory into stable waste forms acceptable for disposal in a deep geologic repository. Eight vitrification treatments that utilize glass, glass ceramic, or basalt waste form matrices are identified. Six of these are discussed in detail, stating the advantages and limitations of each relative to their ability to immobilize GTCC LLW. The report concludes that the waste form most likely to provide the best composite of performance characteristics for GTCC process waste is Iron Enriched Basalt 4 (IEB4)

NEA perspectives on timescales and criteria in post-closure safety of geological disposal

International Nuclear Information System (INIS)

Preter, P. de; Smith, P.; Pescatore, C.; Forinash, B.

2006-01-01

A key challenge in the development of safety cases for geological repositories is associated with the long periods of time over which radioactive wastes that are disposed of in repositories remain hazardous. The OECD Nuclear Energy Agency (NEA) has recently examined issues related to timescales in the context of two projects under the auspices of the Radioactive Waste Management Committee (RWMC): the Timescales Initiative and the Long-Term Safety Criteria (LTSC) Initiative. These projects examine, respectively, the treatment of timescales in actual safety cases and in the development of radiological protection criteria for geological disposal. They treat different aspects of timescales but have some overlap and have shown some convergence of the results achieved to date. Based on these projects, this paper examines general considerations in the handling of timescales, including ethical principles, evolution of the hazards of radioactive waste over time, and uncertainty in the evolution of repository systems (including geological features). The implications of these considerations are examined in terms of repository siting; levels of protection in regulations; planning for pre-closure and post-closure actions; and development and presentation of safety cases. A comparison is made with previous NEA work related to timescales, in order to show evolutions in current understanding. (authors)

NEA perspectives on timescales and criteria in post-closure safety of geological disposal

Energy Technology Data Exchange (ETDEWEB)

Preter, P. de [ONDRAF/NIRAS, Brussels (Belgium); Smith, P. [Safety Assessment Management Ltd, SAM Ltd. (United Kingdom); Pescatore, C.; Forinash, B. [OECD/NEA, Nuclear Energy Agency, 92 - Issy les Moulineaux (France)

2006-07-01

A key challenge in the development of safety cases for geological repositories is associated with the long periods of time over which radioactive wastes that are disposed of in repositories remain hazardous. The OECD Nuclear Energy Agency (NEA) has recently examined issues related to timescales in the context of two projects under the auspices of the Radioactive Waste Management Committee (RWMC): the Timescales Initiative and the Long-Term Safety Criteria (LTSC) Initiative. These projects examine, respectively, the treatment of timescales in actual safety cases and in the development of radiological protection criteria for geological disposal. They treat different aspects of timescales but have some overlap and have shown some convergence of the results achieved to date. Based on these projects, this paper examines general considerations in the handling of timescales, including ethical principles, evolution of the hazards of radioactive waste over time, and uncertainty in the evolution of repository systems (including geological features). The implications of these considerations are examined in terms of repository siting; levels of protection in regulations; planning for pre-closure and post-closure actions; and development and presentation of safety cases. A comparison is made with previous NEA work related to timescales, in order to show evolutions in current understanding. (authors)

Croatian repository construction project - present status and main obstacles

International Nuclear Information System (INIS)

Kucar Dragicevic, S.; Subasic, D.; Schaller, A.; Lokner, V.; Cerskov Klika, M.

1999-01-01

Croatia has been preparing backgrounds for the construction of the repository for low and intermediate radioactive waste on its territory, almost for a decade, now. In the name of Hrvtaska elektroprivreda, the co-owner of the NE Krsko, APO has been co-ordinating and organising numerous activities and projects during that time period. Siting process, safety assessment, disposal technology and repository design and public acceptance issues are the main fields of activities. The overall status of the project at the moment, including the overview of the present status of the main four aspects of activities, will be presented. Relatively, big and important progress made on the project work out during the last two years, as well as the main obstacles we were faced with during that time period, will be discussed.(author)

Project Guarantee 1985. Final repository for low- and intermediate level radioactive wastes: Safety report

International Nuclear Information System (INIS)

Anon.

1985-01-01

Storage of radioactive waste must delay the return of radionuclides to the biosphere for a long period of time and must maintain the release rates at a sufficiently low level for all time. This is achieved with the aid of a series of safety barriers which consist, on the one hand, of technical barriers in the repository and, on the other hand , of natural geological barriers as they occur at the repository location. In order to assess the efficiency of the barriers, the working methods of the technical barriers and the host rock must be understood. This understanding is transferred into quantitative models in order to calculate the safety of the repository. The individual barriers and the methods used to modelling their functions were described in volume NGB 85-07 of the Project Guarantee 1985 report series and the data necessary for modelling were given. The models and data are used in the safety analysis, the results of which are contained in the present report. Safety considerations show that models are available in Switzerland which allow, in principle, an assessment of the long-term behaviour of a repository for low- and intermediate-level waste. The evaluation of earlier studies and experimental work, suitable laboratory measurements and results from field research enable compilation of a representative data-set so that the requirements for quantitative statements on safety of final disposal are met from this side also. The safety calculations show that the radiation doses calculated for a base case scenario with realistic/conservative parameter values are negligibly low. Also, radiation doses which are clearly under the protection standard of 10 mrem per year result for conservative values and the cumulation of several conservative assumptions. Even assuming exposure of the repository by erosion, a radiotoxicity of the soil formed results which is under natural values

Environmental assessment for OPG's deep geologic repository for low and intermediate level waste

International Nuclear Information System (INIS)

Barker, D.; Rawlings, M.; Beal, A.

2011-01-01

The environmental assessment process for the Deep Geologic Repository (DGR) Project was initiated very early in the planning stages. Feasibility studies were initiated in 2003, after Ontario Power Generation (OPG) and the Municipality of Kincardine signed a Memorandum of Understanding agreeing to assess options for long-term management of low and intermediate level waste (L and ILW) options at the Bruce nuclear site. The location of the DGR, in the Municipality of Kincardine, is based on a willing and informed host community. The preferred approach, the DGR at the Bruce nuclear site, was advanced based on results of feasibility studies which looked at a number of options for long-term management of L&ILW and support from the local community and their elected representatives. The federal environmental assessment of the project was initiated following the signing of a Host Community Agreement and completion of a telephone poll, the results of which indicated that the majority of Municipality of Kincardine residents support the project. The environmental assessment began in 2006 as a comprehensive study and was ultimately referred to a joint review panel process in 2009. The environmental assessment considers the potential near-term effects of the construction and operations of the proposed project. Because of the nature of the project, the assessment of effects also considers long-term effects extending out to the million year time-frame, including effects of climate change, glaciations and seismic activity. (author)

Response to state comments on the revised draft northeastern regional characterization reports for the Crystalline Repository Project

International Nuclear Information System (INIS)

1985-08-01

The purpose of this document is to respond to the comments received from the States of the Northeastern Region on the revised draft Northeastern Regional Characterization Reports (RCRs). The responses in this document indicate the manner in which the suggestions or comments received have been considered in modifying the revised draft Northeastern RCRs. Both general comments related to the overall Crystalline Repository Project (CRP) and comments on specific sections of the RCRs are addressed. This document responds to Northeastern State comments on both the revised draft Northeastern Regional Geologic Characterization Report (RGCR) and the revised draft Northeastern Regional Environmental Characterization Report (RECR)

Response to state comments on the revised draft Southeastern Regional Characterization Reports for the Crystalline Repository Project

International Nuclear Information System (INIS)

1985-08-01

The purpose of this document is to respond to the comments received from the states of the Southeastern Region on the revised draft Southeastern Regional Characterization Reports (RCRs). The responses in this document indicate the manner in which the suggestions or comments received have been considered in modifying the revised draft Southeastern RCRs. Both general comments related to the overall Crystalline Repository Project (CRP) and comments on specific sections of the RCRs are addressed. This document responds to Southeastern State comments on both the revised draft Southeastern Regional Geologic Characterization Report (RGCR) and the revised draft Southeastern Regional Environmental Characterization Report (RECR)

Summary of key directives governing permanent disposal in a geologic repository

International Nuclear Information System (INIS)

Sands, S.C. III.

1993-11-01

This document was developed in support of the Idaho National Engineering Laboratory (INEL) Spent Fuel and Waste Management Technology Development Program (SF ampersand WMTDP). It is largely comprised of flow diagrams summarizing the key regulatory requirements which govern permanent disposal in a geologic repository. The key purposes are (1) to provide an easy and effective tool for referencing or cross referencing federal directives (i.e., regulations and orders), (2) to provide a method for examining the requirements in one directive category against the requirements in another, and (3) to list actions that must be taken to ensure directive compliance. The document is categorically broken down into a Transportation section and a Mined Geologic Disposal System (MGDS) section to ensure that the interrelationship of the entire disposal system is considered. The Transportation section describes the transportation packaging requirements, testing methods, and safety requirements imposed on fissile material shipments. The MGDS section encompasses technical aspects involved in siting, licensing, waste interaction with the container, container design features, physical characteristics of the surrounding environment, facility design features, barrier systems, safety features, criticality considerations, migration restrictions, implementation guidelines, and so forth. For purposes of illustration, the worst case scenario is outlined. It is important that the approaches and considerations contained in this document be integrated into the efforts of the SF ampersand WMTDP so that every applicable aspect of the regulatory requirements can be evaluated to avoid investing large sums of money into projects that do not take into account all of the aspects of permanent waste disposal. Not until an overall picture and clear understanding of these regulations is established can a basis be developed to govern the direction of future activities of the SF ampersand WMTDP

Archive of Geosample Data and Information from the Oregon State University (OSU) College of Earth, Ocean and Atmospheric Sciences (CEOAS) Marine Geology Repository (MGR)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Oregon State University Marine Geology Repository (OSU-MGR) is a partner in the Index to Marine and Lacustrine Geological Samples (IMLGS) database, contributing...

SemanticOrganizer: A Customizable Semantic Repository for Distributed NASA Project Teams

Science.gov (United States)

Keller, Richard M.; Berrios, Daniel C.; Carvalho, Robert E.; Hall, David R.; Rich, Stephen J.; Sturken, Ian B.; Swanson, Keith J.; Wolfe, Shawn R.

2004-01-01

SemanticOrganizer is a collaborative knowledge management system designed to support distributed NASA projects, including diverse teams of scientists, engineers, and accident investigators. The system provides a customizable, semantically structured information repository that stores work products relevant to multiple projects of differing types. SemanticOrganizer is one of the earliest and largest semantic web applications deployed at NASA to date, and has been used in diverse contexts ranging from the investigation of Space Shuttle Columbia's accident to the search for life on other planets. Although the underlying repository employs a single unified ontology, access control and ontology customization mechanisms make the repository contents appear different for each project team. This paper describes SemanticOrganizer, its customization facilities, and a sampling of its applications. The paper also summarizes some key lessons learned from building and fielding a successful semantic web application across a wide-ranging set of domains with diverse users.

Mining and engineering aspects and variants for the underground construction of a deep geological repository for radioactive waste and spent nuclear fuel

International Nuclear Information System (INIS)

Milchev, M.; Michailov, B.; Nanovska, E.; Harizanov, A.

2003-01-01

The aim of the present report is to investigate and to describe systematically the foreign experience, scientific and technical achievements and stages of development concerning the mining and engineering aspects and variants for underground construction of a deep geological repository for radioactive waste (RAW) and spent nuclear fuel (SNF). The ideal solution in managing the problems with harmful wastes seems to be either to remove them permanently from Earth (which is related with high risks and high costs) or to transform long-lived radionuclides to short-lived radionuclides using nuclear transmutation processes in a reactor or a particle accelerator. The latter is also a complex and immensely costly process and it can only reduce the quantities of some long-lived radionuclides, which can be then disposed in a geological repository. At present, the deep geological disposal remains the only solution for solving the problem with the hazard of storing radioactive wastes. The report submits a brief description and systematization of the performed investigations, accompanied by analysis of the scientific and technical level on world scale. The analysis is related with the particular geological conditions and the existing scientific studies available so far in Bulgaria. The main conclusions are that the complex scientific-technical and engineering problems related with the construction of a deep geological repository for RAW and SNF require long-term scientific investigations and preliminary complex works and it is high time to launch them in Bulgaria. (authors)

Quality assurance records system for research and development activities in support of geologic repository programs

International Nuclear Information System (INIS)

Smith, J.W.; Ryder, D.E.

1987-01-01

The Pacific Northwest Laboratory (PNL), which is operated by Battelle Memorial Institute for the Department of Energy, is conducting site-specific research for all three candidate sites for the first geologic high-level waste repository, as well as generic research for the second repository. In conjunction with this effort, PNL has developed a quality assurance (QA) program that is applicable to all organizations that are performing research and development (R and D) activities in support of the repository programs. This QA program meets the basic and supplemental requirements of ANSI/ASME NQA-1-1983 and the Nuclear Regulatory Commission (NRC) Review Plan for QA Programs for Site Characterization of High Level Nuclear Waste Repositories. A key part of this program is the handling of QA records that may ultimately support the licensing process for the repository. This paper describes a QA records system that is flexible enough to accommodate several types of research, such as paper studies, test method development, site characterization studies, software development, and hardware design. In addition, the QA records system is acceptable to a variety of sponsors who have licensing concerns. The QA procedures and their relation to the requirements are described. Most important is the discussion on the approaches used to assure that the records are organized such that the user can readily recreate or defend data, conclusions, and recommendations resulting from the research

Response to state comments on the draft regional characterization reports for the Crystalline Repository Project

International Nuclear Information System (INIS)

1984-11-01

In May, 1983, the US Department of Energy (DOE) Crystalline Repository Project Office (CPO) issued six draft Regional Characterization Reports (RCRs) for review and comment to the 17 Crystalline States comprising the Northeastern, Southeastern, and North Central crystalline regions. Comment letters were received from 13 of the 17 states. The more than 2000 comments generally focused on the quality and content of the characterization reports and on their intended use in region-to-area screening. These comments were paraphrased and grouped into 23 subjects within the following four topical areas: (1) General and Programmatic; (2) Geologic; (3) Environmental and Socioeconomic; and (4) Editorial. This document provides responses to the comments submitted by the states

Sandstone uranium deposits of Meghalaya: natural analogues for radionuclide migration and backfill material in geological repository for high level radioactive waste disposal

International Nuclear Information System (INIS)

Bajpai, R.K.; Narayan, P.K.

2008-01-01

Sandstone uranium deposits serve as potential natural analogue to demonstrate safety offered by geological media against possible release of nuclear waste from their confinement and migration towards biosphere. In this study, available database on geochemical aspects of Domisiat uranium deposit of Meghalaya has been evaluated to highlight the behavior of radionuclides of concern over long term in a geological repository. Constituents like actinides (U and Th), fission products and RE elements are adequately retained in clays and organic matters associated with these sandstone deposits. The study also highlights the possibility of utilization of lean ore discarded during mining and milling as backfill material in far field areas and optimizing near field buffers/backfills in a geological repository located in granitic rocks in depth range of 400-500m. (author)

Radionuclide transport behavior in a generic geological radioactive waste repository.

Science.gov (United States)

Bianchi, Marco; Liu, Hui-Hai; Birkholzer, Jens T

2015-01-01

We performed numerical simulations of groundwater flow and radionuclide transport to study the influence of several factors, including the ambient hydraulic gradient, groundwater pressure anomalies, and the properties of the excavation damaged zone (EDZ), on the prevailing transport mechanism (i.e., advection or molecular diffusion) in a generic nuclear waste repository within a clay-rich geological formation. By comparing simulation results, we show that the EDZ plays a major role as a preferential flowpath for radionuclide transport. When the EDZ is not taken into account, transport is dominated by molecular diffusion in almost the totality of the simulated domain, and transport velocity is about 40% slower. Modeling results also show that a reduction in hydraulic gradient leads to a greater predominance of diffusive transport, slowing down radionuclide transport by about 30% with respect to a scenario assuming a unit gradient. In addition, inward flow caused by negative pressure anomalies in the clay-rich formation further reduces transport velocity, enhancing the ability of the geological barrier to contain the radioactive waste. On the other hand, local high gradients associated with positive pressure anomalies can speed up radionuclide transport with respect to steady-state flow systems having the same regional hydraulic gradients. Transport behavior was also found to be sensitive to both geometrical and hydrogeological parameters of the EDZ. Results from this work can provide useful knowledge toward correctly assessing the post-closure safety of a geological disposal system. © 2014, National Ground Water Association.

Design information verification for spent fuel conditioning plants and for geological repositories

International Nuclear Information System (INIS)

Myatt, J.; Ward, M.D.

1995-01-01

The disposal of spent fuel is a major option for the back-end of the nuclear fuel cycle. It will require the construction, operation and eventual closure of conditioning plants and geological repositories. Consequently, a safeguards approach including Design Information Verification (DIV) must be developed for these facilities. DIV Is the examination of a completed facility to verify that it has been built to the design declared by the operator. Although DIV takes place chiefly before a plant begins routine operation, there is a continuing interest in ensuring that the plant remains as declared. That is, that the continuity of knowledge of design information is maintained during the operational phase of the plant and also post closure if necessary. A major problem with DIV of a repository is that there will be continuous structural changes during its operational life requiring advanced or special techniques for reverification. Some of these are briefly reviewed. Furthermore, since a disposal facility is expected to be operational for several decades, new mining technology may also have an impact on the DIV methods employed. Another factor in the safeguards supervision of a repository is that when the fuel has been backfilled and/or scaled in place a reassay will be a very costly exercise. The role of DIV in such novel circumstances must, therefore, be fully considered

Waste repository planned for Bruce Site

International Nuclear Information System (INIS)

King, F.

2004-01-01

Ontario Power Generation (OPG) and Kincardine, the municipality nearest the Bruce site, have agreed in principal to the construction of a deep geologic repository for low and medium level radioactive waste on the site. The two parties signed the 'Kincardine Hosting Agreement' on October 13, 2004 to proceed with planning, seek regulatory approval and further public consultation of the proposed project. A construction Licence is not expected before 2013. (author)

Sorption of plutonium and americium on repository, backfill and geological materials relevant to the JNFL low-level radioactive waste repository at Rokkasho-Mura

International Nuclear Information System (INIS)

Baston, G.M.N.; Berry, J.A.; Brownsword, M.; Heath, T.G.; Tweed, C.J.; Williams, S.J.

1995-01-01

An integrated program of batch sorption experiments and mathematical modeling has been carried out to study the sorption of plutonium and americium on a series of repository, backfill and geological materials relevant to the JNFL low-level radioactive waste repository at Rokkasho-Mura. The sorption of plutonium and americium on samples of concrete, mortar, sand/bentonite, tuff, sandstone and cover soil has been investigated. In addition, specimens of bitumen, cation and anion exchange resins, and polyester were chemically degraded. The resulting degradation product solutions, alongside solutions of humic and isosaccharinic acids were used to study the effects on plutonium sorption onto concrete, sand/bentonite and sandstone. The sorption behavior of plutonium and americium has been modeled using the geochemical speciation program HARPHRQ in conjunction with the HATCHES database

Overview of adaptive phased management repository design development

International Nuclear Information System (INIS)

Russell, S.

2011-01-01

The Nuclear Waste Management Organization is implementing Adaptive Phased Management, Canada's plan for long-term management of used nuclear fuel. The organization is proceeding with the process for selecting a site in partnership with an informed and willing host community to safely and securely container and isolate used nuclear fuel in a deep geological repository in a suitable rock formation. Adaptive Phased Management is the culmination of more than 30 years of research, development and demonstration of repository concepts in Canada. Adaptive Phased Management uses a phased and adaptive step-wise approach to the multi-barrier system which is consistent with the long-term waste management approaches being developed in many other countries with nuclear power programs such as Sweden, Finland, Switzerland, the United Kingdom and France. The Nuclear Waste Management Organization is examining and developing conceptual designs for a deep geological repository and associated facilities for the placement of used nuclear fuel in long-lived containers. This paper will examine two of these generic conceptual designs which have recently been refined and updated. These conceptual designs will be used to support a pre-project review of repository design and safety by the Canadian Nuclear Safety Commission. (author)

Project Guarantee 1985. Final repository for high-level radioactive wastes: Safety report

International Nuclear Information System (INIS)

Anon.

1985-01-01

Disposal of radioactive was involves preventing releases to the biosphere for a long period of time and subsequently limiting the magnitude of releases by means of a series of safety barriers: the waste solidification matrix (borosilicate glass), massive steel canisters in highly compacted bentonite, sealing of void spacer and access routes on repository closure. The geological barriers are formed by the crystalline bed-rock and the overlying sedimentary layers. In order to perform a safety assessment the behaviour of these technical barriers and of the host rock must be understood and this understanding must be translated into quantitative models which allow calculation of repository performance. For the particular case of a Swiss repository, the main criterion is the individual dose limit of 10 mrem/year, which is given in the safety guidelines of the Swiss authorities. The procedure for the safety analysis involves examination of all scenarios which could give rise to radionuclide release from the repository. Qualitative considerations of both the magnitude of their consequences and their likelihood are used in order to identify a restricted number of scenarios for quantitative analysis

Derivation of parameters necessary for the evaluation of performance of sites for deep geological repositories with particular reference to bedded salt, Livermore, California. Volume I. Main text

International Nuclear Information System (INIS)

Ashby, J.P.; Rawlings, G.E.; Soto, C.A.; Wood, D.F.; Chorley, D.W.

1979-12-01

A survey of parameters to be considered in the evaluation of sites for deep geologic nuclear waste repositories is presented. As yet, no comprehensive site selection procedure or performance evaluation approach has been adopted. A basis is provided for the development of parameters by discussing both site selection and performance evaluation. Three major groups of parameters are considered in this report: geologic, mining/rock mechanics, and hydrogeologic. For each type, the role of the parameter in the evaluation of repository sites is discussed. The derivation of the parameter by measurement, correlation, inference, or other method is discussed. Geologic parameters define the framework of the repository site and can be used in development of conceptual models and the prediction of long-term performance. Methods for deriving geological parameters include mapping, surveying, drilling, geophysical investigation, and historical and regional analysis. Rock mechanics/mining parameters are essential for the prediction of short-term performance and the development of initial conditions for modeling of long-term performance. Rock mechanics/mapping parameters can be derived by field or laboratory investigation, correlation, and theoretically or empirically based inference. Hydrogeologic parameters are the most important for assessment of long-term radionuclide confinement, since transport throughout the regional hydrogeologic system is the most likely mode of radionuclide escape from geologic repositories. Hydrogeologic parameters can be derived by hydrogeologic mapping and interpretation, hydrogeologic system modeling, field measurements, and lab tests. Procedures used in determination and statistical evaluation of geologic and rock mechanics parameters are discussed

Derivation of parameters necessary for the evaluation of performance of sites for deep geological repositories with particular reference to bedded salt, Livermore, California. Volume I. Main text

Energy Technology Data Exchange (ETDEWEB)

Ashby, J.P.; Rawlings, G.E.; Soto, C.A.; Wood, D.F.; Chorley, D.W.

1979-12-01

A survey of parameters to be considered in the evaluation of sites for deep geologic nuclear waste repositories is presented. As yet, no comprehensive site selection procedure or performance evaluation approach has been adopted. A basis is provided for the development of parameters by discussing both site selection and performance evaluation. Three major groups of parameters are considered in this report: geologic, mining/rock mechanics, and hydrogeologic. For each type, the role of the parameter in the evaluation of repository sites is discussed. The derivation of the parameter by measurement, correlation, inference, or other method is discussed. Geologic parameters define the framework of the repository site and can be used in development of conceptual models and the prediction of long-term performance. Methods for deriving geological parameters include mapping, surveying, drilling, geophysical investigation, and historical and regional analysis. Rock mechanics/mining parameters are essential for the prediction of short-term performance and the development of initial conditions for modeling of long-term performance. Rock mechanics/mapping parameters can be derived by field or laboratory investigation, correlation, and theoretically or empirically based inference. Hydrogeologic parameters are the most important for assessment of long-term radionuclide confinement, since transport throughout the regional hydrogeologic system is the most likely mode of radionuclide escape from geologic repositories. Hydrogeologic parameters can be derived by hydrogeologic mapping and interpretation, hydrogeologic system modeling, field measurements, and lab tests. Procedures used in determination and statistical evaluation of geologic and rock mechanics parameters are discussed.

Framework and Challenges for Initiating Multinational Cooperation for the Development of a Radioactive Waste Repository

International Nuclear Information System (INIS)

2016-01-01

This publication is concerned with radioactive waste that requires geological disposal. It discusses the partnership arrangements necessary for the development of a multinational repository for disposal of this waste, but it also emphasizes that countries should not rely solely on a multinational solution and should in addition have coherent national plans for disposal (a dual track strategy). The publication focuses on multinational approaches based on the IAEA scenario for cooperation among countries in joint projects for the establishment of a shared geological repository. It describes the phased approach that would be needed, indicating the decision processes to be undertaken by partners in the multinational project, both within a national context and in the scope of the joint endeavour. It highlights a wide range of legal and institutional aspects, including the contractual obligations among partners, the economic and financial arrangements, liabilities, nuclear security, regulatory and legislative aspects, waste transportation arrangements, and social issues. It also addresses the uncertainties and risks involved in the implementation of a multinational repository

The Hidden Risk Decisions in Waste Repository Regulation

International Nuclear Information System (INIS)

Frishman, Steve

2001-01-01

event or process occur. Because of the nature of the uncertainties, some of which can not be eliminated or reduced, the performance assessment results could broadly span the established performance standard. If the regulator considers the results to be usable, the resulting regulatory conclusion then can lie with which statistical parameter, eg. mean, median, 95th percentile, etc., the regulator chooses as a basis for compliance determination. The regulator's values then will have been imposed on the affected population, generations into the future. Risk, when applied in the geologic repository context, has two faces. First is the possibility that the repository will not contain the waste in the manner projected by the performance assessment, even if the performance assessment indicates that the established individual dose limit will not be exceeded. And second, application of the risk-informed, performance-based approach results in masking the high dose consequences of low probability events. An example illustrating this effect is described. In the case of geologic repositories, the risk informed, performance based approach to regulation can result in the regulator embedding its risk acceptance values into the compliance decision in unexpected ways that likely are at odds with the values of those who are placed at risk. The uncertain nature of repository performance assessment is the dominant source of risk in the risk informed, performance based regulatory approach. For this reason, performance assessment, alone, should not be relied upon to determine a geologic repository's regulatory compliance methodology

New developments in measurement technology relevant to the studies of deep geological repositories in domed salt and basalt

International Nuclear Information System (INIS)

Ramirez, A.L.; Mao, N.H.

1980-01-01

This report briefly describes recent geophysical and geotechnical instrumentation developments relevant to the studies of deep geologic repositories. Special emphasis has been placed on techniques that appear to minimize measurement problems associated with repositories constructed in basalt or domed salt. Included in the listing are existing measurement capabilities and deficiencies that have been identified by a few authors and instrumentation workshops that have assessed the capabilities of existing instrumentation with respect to repository applications. These deficiencies have been compared with the reported advantages and limitations of the new developments described. Based on these comparisons, areas that merit further research and development have been identified. The report is based on a thorough literature review and on discussions with several instrumentation specialists involved in instrumentation development

Earthquakes - a danger to deep-lying repositories?

International Nuclear Information System (INIS)

2012-03-01

This booklet issued by the Swiss National Cooperative for the Disposal of Radioactive Waste NAGRA takes a look at geological factors concerning earthquakes and the safety of deep-lying repositories for nuclear waste. The geological processes involved in the occurrence of earthquakes are briefly looked at and the definitions for magnitude and intensity of earthquakes are discussed. Examples of damage caused by earthquakes are given. The earthquake situation in Switzerland is looked at and the effects of earthquakes on sub-surface structures and deep-lying repositories are discussed. Finally, the ideas proposed for deep-lying geological repositories for nuclear wastes are discussed

Preliminary on-surface experiments for backfilling a HLW repository: the ESDRED project

International Nuclear Information System (INIS)

Bastiaens, W.

2007-01-01

ESDRED is a technological integrated project within the context of the Sixth Framework Program of EURATOM. The project aims to demonstrate the technical feasibility at an industrial scale of specific technologies related to the construction, operation and closure of a deep geological repository for spent fuel and long-lived radioactive waste. The Belgian design for high level waste disposal is based on the so-called Supercontainer concept. Within this concept, the waste is encased in a carbon steel overpack, which is consequently fitted into a 70 cm thick concrete shell, in its turn enveloped by a stainless steel liner. A Supercontainer measures about 2 m in diameter. In the design of the repository, the Supercontainers will be emplaced, one after the other, in disposal galleries. The space between the Supercontainers and the gallery lining needs to be filled up with a solid material. The most essential function of this component, referred to as backfill, is to prevent a collapse of the gallery. A secondary function is to limit the presence of free oxygen, to limit corrosion. In the ESDRED project EIG EURIDICE, together with SCK-CEN and ONDRAF/NIRAS, investigates technologies to apply the backfill. Two options to apply the backfill were investigated within the ESDRED project: fill the gap with a granular material and backfill the gap with a grout. The prime operational target will be to achieve a 100 percent filling of the gap. A wide variety of materials was tested. A number of considerations regarding long-term safety and operational feasibility impose constraints on the backfill component:it should preserve the corrosion-protective environment established by the Supercontainer; it should not act as a thermal isolator; it should not introduce organic materials that can give rise to the formation of migration-enhancing complexes between radionuclides and soluble organic compounds; it should be feasible to construct at a sufficiently high rate; the strength of the

Approach to geologic repository post closure system performance assessment

International Nuclear Information System (INIS)

Pahwa, S.B.; Felton, W.; Duguid, J.O.

1992-01-01

An essential part of the license application for a geologic repository will be the demonstration of compliance with the standards set by the Environmental Protection Agency. The performance assessments that produce the demonstration must rely on models of various levels of detail. The most detailed of these models are needed for understanding thoroughly the complex physical and chemical processes affecting the behavior of the system. For studying the behavior of major components of the system, less detailed models are often useful. For predicting the behavior of the total system, models of a third kind may be needed. These models must cover all the important processes that contribute to the behavior of the system, because they must estimate the behavior under all significant conditions for 10,000 years. In addition, however, computer codes that embody these models must calculate very rapidly because of the EPA standard's requirement for probabilistic estimates, which will be produced by sampling thousands of times from probability distributions of parameters. For this reason, the total-system models must be less complex than the detailed-process and subsystem models. The total-system performance is evaluated through modeling of the following components: Radionuclide release from the engineered-barrier system. Fluid flow in the geologic units. Radionuclide transport to the accessible environment. Radionuclide release to the accessible environment and dose to man

New simulation tools for long-term hydraulic design for a geological repository

International Nuclear Information System (INIS)

Richard, S.; Chaudon, L.

1995-01-01

Hydraulic concepts for a geological repository were investigated. Numerical simulations were adapted for this purpose and an experimental rheoelectric method based on an analogy between hydraulic flows and electric currents was developed. The results are discussed in this paper. A simplified representation of the host rock was adopted to account for the geometric details of the concept; this rock was described by a homogeneous porous medium associated with two major discontinuities. Steady-state hydraulic conditions were considered, and heating by the waste packages was assumed to be negligible (these conditions correspond to the long-term repository setting). The hydraulic structures obtained by the two methods are comparable, but significant differences were observed in the drained water distribution in the excavations; these discrepancies highlight the importance of the calculation mesh dimensions. Drainage barriers (drainage drifts and boreholes) surrounding the disposal boreholes may reduce water circulation in the disposal areas to their initial levels by constituting a partial hydraulic Faraday cage. This could be achieved with a reasonable number of boreholes if necessary

Evaluation of radionuclide migration in the homogeneous system of a geological repository

International Nuclear Information System (INIS)

Prvakova, S.; Duran, J.; Necas, V.

2005-01-01

The aim of this paper is to study radionuclide migration and release from a deep underground repository situated in a clay formation. An insight into the processes influencing the radionuclide transport in the near field and far field will be presented. For the calculation, a set of radionuclides has been chosen, considering the half-life, decay chains, capacity of the sorption, solubility limits and diffusion coefficients. The migration of radionuclides is dependent on transport properties of the particular nuclide. Due to the low hydraulic conductivity of the backfill material and clay geological formation, the transport in the repository occurs mainly by diffusion. The migration rate will be influenced by the water chemistry, solubility, retardation and diffusive properties of the nuclides, and the water flow rate in the clay. The release rates of radionuclides from the geosphere to the biosphere will be converted into the indicative dose rates using dose conversion factors for ingestion. The impact of the critical group is considered via consumption of meat, root vegetables and drinking water from wells. (author)

Repository seal materials performance for a SALT Repository Project 5-year code/model development plan: Draft

International Nuclear Information System (INIS)

1987-06-01

This document describes an integrated laboratory testing and model development effort for the seal system for a high-level nuclear waste repository in salt. The testing and modeling efforts are designed to determine seal material response in the repository environment, to provide models of seal system components for performance assessment, and to assist in the development of seal system designs. A code/model development and performance analysis program will be performed to predict the short- and long-term response of seal materials and seal components. The results from these analyses will be used to support the material testing activities on this contract and to support performance assessment activities that are conducted in other parts of the Salt Repository Project (SRP). 48 refs., 15 figs., 4 tabs

Staff Technical Position on geological repository operations area underground facility design: Thermal loads

International Nuclear Information System (INIS)

Nataraja, M.S.

1992-12-01

The purpose of this Staff Technical Position (STP) is to provide the US Department of Energy (DOE) with a methodology acceptable to the Nuclear Regulatory Commission staff for demonstrating compliance with 10 CFR 60.133(i). The NRC staff's position is that DOE should develop and use a defensible methodology to demonstrate the acceptability of a geologic repository operations area (GROA) underground facility design. The staff anticipates that this methodology will include evaluation and development of appropriately coupled models, to account for the thermal, mechanical, hydrological, and chemical processes that are induced by repository-generated thermal loads. With respect to 10 CFR 60.133(i), the GROA underground facility design: (1) should satisfy design goals/criteria initially selected, by considering the performance objectives; and (2) must satisfy the performance objectives 10 CFR 60.111, 60.112, and 60.113. The methodology in this STP suggests an iterative approach suitable for the underground facility design

Geologic report of the Maquoketa Shale, New Albany Shale, and Borden Group rocks in the Illinois Basin as potential solid waste repository sites

International Nuclear Information System (INIS)

Droste, J.B.; Vitaliano, C.J.

1976-06-01

We have evaluated the Illinois Basin in order to select a ''target site'' for a possible solid nuclear waste repository. In the process we have been mindful of geology (particularly stratigraphy and lithology and structure), terrane, population density, land use, land ownership and accessibility. After taking these restrictions into account, we have singled out a strip of land in south central Indiana in which we have selected four potential sites worthy of further exploration. In three of the sites the geology, lithology, and depth below the surface are more than adequate for crypt purposes in two separate formations--the Maquoketa Shale of the Ordovician System and the New Albany Shale-Borden Group of the Upper Devonian-Mississippian Systems. The interval between the two is several hundred feet. The geology and associated features in the fourth site are undoubtedly similar to those in the first three. In all four selections a sizeable proportion of the land is in public ownership and the population density in the nonpublicly owned land is low. The geology, lithology, and position of the target formations have been projected into the sites in question from data provided by drill core records of the Indiana Geological Survey. Precise details would, of course, require exploratory drilling on the selected site

Communication on the Safety Case for a Deep Geological Repository

International Nuclear Information System (INIS)

Bailey, Lucy; Bernier, Frederik; Bollingerfehr, Wilhelm; Cunado, Miguel; Ilett, Doug; Kwong, Gloria; ); Noseck, Ulrich; Roehlig, Klaus; Van Luik, Abe; Weber, Jan; Weetjens, Eef

2017-01-01

Communication has a specific role to play in the development of deep geological repositories. Building trust with the stakeholders involved in this process, particularly within the local community, is key for effective communication between the authorities and the public. There are also clear benefits to having technical experts hone their communication skills and having communication experts integrated into the development process. This report has compiled lessons from both failures and successes in communicating technical information to non-technical audiences. It addresses two key questions in particular: what is the experience base concerning the effectiveness or non-effectiveness of different tools for communicating safety case results to a non-technical audience and how can communication based on this experience be improved and included into a safety case development effort from the beginning? (authors)

Assessment of effectiveness of geologic isolation systems: the AEGIS geologic simulation model

International Nuclear Information System (INIS)

Foley, M.G.; Petrie, G.M.

1981-02-01

Assessment of the post-closure performance of a nuclear waste repository has two basic components: the identification and analysis of potentially disruptive sequences and the pattern of geologic events and processes causing each sequence, and the identification and analysis of the environmental consequences of radionuclide transport and interactions subsequent to disruption of a repository. The AEGIS Scenario Analysis Task is charged with identifying and analyzing potenially disruptive sequences of geologic events and processes. The Geologic Simulation Model (GSM) was developed to evaluate the geologic/hydrologic system surrounding an underground repository, and describe the phenomena that alone, or in concert, could perturb the system and possibly cause a loss of repository integrity. The AEGIS approach is described in this report. It uses an integrated series of models for repository performance analysis; the GSM for a low-resolution, long-term, comprehensive evaluation of the geologic/hydrologic system, followed by more detailed hydrogeologic, radionuclide transport, and dose models to more accurately assess the consequences of disruptive sequences selected from the GSM analyses. This approach is felt to be more cost-effective than an integrated one because the GSM can be used to estimate the likelihoods of different potentially disruptive future evolutionary developments within the geologic/hydrologic system. The more costly consequence models can then be focused on a few disruptive sequences chosen for their representativeness and effective probabilities

Rock mechanics for hard rock nuclear waste repositories

International Nuclear Information System (INIS)

Heuze, F.E.

1981-09-01

The mined geologic burial of high level nuclear waste is now the favored option for disposal. The US National Waste Terminal Storage Program designed to achieve this disposal includes an extensive rock mechanics component related to the design of the wastes repositories. The plan currently considers five candidate rock types. This paper deals with the three hard rocks among them: basalt, granite, and tuff. Their behavior is governed by geological discontinuities. Salt and shale, which exhibit behavior closer to that of a continuum, are not considered here. This paper discusses both the generic rock mechanics R and D, which are required for repository design, as well as examples of projects related to hard rock waste storage. The examples include programs in basalt (Hanford/Washington), in granitic rocks (Climax/Nevada Test Site, Idaho Springs/Colorado, Pinawa/Canada, Oracle/Arizona, and Stripa/Sweden), and in tuff

Preservation of Records, Knowledge and Memory across generations. An International Project of the NEA/RWMC. Foundations and guiding principles for the preservation of records, knowledge and memory across generations: A focus on the post-closure phase of geological repositories. A Collective Statement of the NEA Radioactive Waste Management Committee

International Nuclear Information System (INIS)

2011-11-01

Preservation of Records, Knowledge and Memory (RK and M) across generations is needed to support lengthy and complex decision-making processes across long operational and post-operational lifetimes of radioactive waste repositories. It is a recognised management task that spans unprecedented time-horizons in which technical, scientific, societal and cultural information is interwoven. Experience indicates that RK and M need to be actively managed from the start of the waste management programmes. Several radioactive waste disposal programmes are now approaching implementation. The NEA Radioactive Waste Management Committee (RWMC) has created an international project addressing the preservation of RK and M across generations. This collective statement summarises the current understanding of the relevant needs and challenges to be faced. It underscores the willingness of the RWMC member organisations to work together and support national programmes to move forward in this area. Research and development underway on the disposal of long-lived radioactive waste in engineered facilities or repositories located in deep geological formations has confirmed this form of disposal as the ultimate solution for the long-term protection of human beings and the environment, eliminating the need for human intervention and maintenance. While the intention is not to abandon repositories for geological disposal of radioactive waste, either before or after closure, as with many long-term projects, it is a question of minimising the risks of losing records, knowledge and memory (RK and M). The international community of radioactive waste professionals is leading advanced work in this important area. At the end of its first phase of RK and M work, the RWMC observed that the context has changed considerably since the 1980's, when RK and M preservation was thought to serve the sole function of deterring intrusion into a repository. The goal today is to preserve information for future

In situ experiments for disposal of radioactive wastes in deep geological formations

International Nuclear Information System (INIS)

1987-12-01

This report reviews the current status of in-situ experiments undertaken to assess various concepts for disposal of spent fuel and reprocessed high-level waste in deep geological formations. Specifically it describes in-situ experiments in three geological formations - clay, granite and domed salt. The emphasis in this report is on the in-situ experiments which deal with the various issues related to the near-field effects in a repository and the geological environment immediately surrounding the repository. These near-field effects are due to the disturbance caused by both the construction of the repository and the waste itself. The descriptions are drawn primarily from four underground research facilities: the Underground Experimental Facility, Belgium (clay), the Stripa Project, Sweden and the Underground Research Laboratory, Canada (granite) and the Asse Mine, Federal Republic of Germany (salt). 54 refs, figs and tab

Canada's Deep Geological Repository for Used Nuclear Fuel - Geo-scientific Site Evaluation Process - 13117

International Nuclear Information System (INIS)

Blyth, Alec; Ben Belfadhel, Mahrez; Hirschorn, Sarah; Hamilton, Duncan; McKelvie, Jennifer

2013-01-01

The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable rock formation at a depth of approximately 500 meters (m) (1,640 feet [ft]). In May 2010, the NWMO published a nine-step site selection process that serves as the road map to decision-making on the location for the deep geological repository. The safety and appropriateness of any potential site will be assessed against a number of factors, both technical and social in nature. The selected site will be one that can be demonstrated to be able to safely contain and isolate used nuclear fuel, protecting humans and the environment over the very long term. The geo-scientific suitability of potential candidate sites will be assessed in a stepwise manner following a progressive and thorough site evaluation process that addresses a series of geo-scientific factors revolving around five safety functions. The geo-scientific site evaluation process includes: Initial Screenings; Preliminary Assessments; and Detailed Site Evaluations. As of November 2012, 22 communities have entered the site selection process (three in northern Saskatchewan and 18 in northwestern and southwestern Ontario). (authors)

Repository operational criteria analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1992-08-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations, considering the interfaces and impacts of any potential changes to those regulations. The study addresses regulatory criteria related to the preclosure aspects of the geologic repository. The study task developed regulatory concepts or potential repository operational criteria (PROC) based on analysis of a repository's safety functions and other regulations for similar facilities. These regulatory concepts or PROC were used as a basis to assess the sufficiency and adequacy of the current criteria in 10 CFR Part 60. Where the regulatory concepts were same as current operational criteria, these criteria were referenced. The operations criteria referenced or the PROC developed are given in this report. Detailed analyses used to develop the regulatory concepts and any necessary PROC for those regulations that may require a minor change are also presented. The results of the ROC task showed a need for further analysis and possible major rule change related to the design bases of a geologic repository operations area, siting, and radiological emergency planning

Selection of nuclide decay chains for use in the assessment of the radiological impact of geological repositories for radioactive waste

International Nuclear Information System (INIS)

Thorne, M.C.

1982-12-01

The criteria for selecting nuclide decay chains for use in the assessment of the radiological impact of geological repositories for radioactive waste are given. The reduced chains recommended for use with SYVAC are described. (author)

Evaluation of methods and tools to develop safety concepts and to demonstrate safety for an HLW repository in salt. Final report

Energy Technology Data Exchange (ETDEWEB)

Bollingerfehr, W.; Buhmann, D.; Doerr, S.; and others

2017-03-15

Salt formations have been the preferred option as host rocks for the disposal of high level radioactive waste in Germany for more than 40 years. During this period comprehensive geological investigations have been carried out together with a broad spectrum of concept and safety related R and D work. The behaviour of an HLW repository in salt formations, particularly in salt domes, has been analysed in terms of assessment of the total system performance. This was first carried out for concepts of generic waste repositories in salt and, since 1998, for a repository concept with specific boundary conditions, taking the geology of the Gorleben salt dome as an example. Suitable repository concepts and designs were developed, the technical feasibility has been proven and operational and long-term safety evaluated. Numerical modelling is an important input into the development of a comprehensive safety case for a waste repository. Significant progress in the development of numerical tools and their application for long-term safe ty assessment has been made in the last two decades. An integrated approach has been used in which the repository concept and relevant scientific and engineering data are combined with the results from iterative safety assessments to increase the clarity and the traceability of the evaluation. A safety concept that takes full credit of the favourable properties of salt formations was developed in the course of the R and D project ISIBEL, which started in 2005. This concept is based on the safe containment of radioactive waste in a specific part of the host rock formation, termed the containment providing rock zone, which comprises the geological barrier, the geotechnical barriers and the compacted backfill. The future evolution of the repository system will be analysed using a catalogue of Features, Events and Processes (FEP), scenario development and numerical analysis, all of which are adapted to suit the safety concept. Key elements of the

Evaluation of methods and tools to develop safety concepts and to demonstrate safety for an HLW repository in salt. Final report

International Nuclear Information System (INIS)

Bollingerfehr, W.; Buhmann, D.; Doerr, S.

2017-03-01

Salt formations have been the preferred option as host rocks for the disposal of high level radioactive waste in Germany for more than 40 years. During this period comprehensive geological investigations have been carried out together with a broad spectrum of concept and safety related R and D work. The behaviour of an HLW repository in salt formations, particularly in salt domes, has been analysed in terms of assessment of the total system performance. This was first carried out for concepts of generic waste repositories in salt and, since 1998, for a repository concept with specific boundary conditions, taking the geology of the Gorleben salt dome as an example. Suitable repository concepts and designs were developed, the technical feasibility has been proven and operational and long-term safety evaluated. Numerical modelling is an important input into the development of a comprehensive safety case for a waste repository. Significant progress in the development of numerical tools and their application for long-term safe ty assessment has been made in the last two decades. An integrated approach has been used in which the repository concept and relevant scientific and engineering data are combined with the results from iterative safety assessments to increase the clarity and the traceability of the evaluation. A safety concept that takes full credit of the favourable properties of salt formations was developed in the course of the R and D project ISIBEL, which started in 2005. This concept is based on the safe containment of radioactive waste in a specific part of the host rock formation, termed the containment providing rock zone, which comprises the geological barrier, the geotechnical barriers and the compacted backfill. The future evolution of the repository system will be analysed using a catalogue of Features, Events and Processes (FEP), scenario development and numerical analysis, all of which are adapted to suit the safety concept. Key elements of the

Production, consumption and transport of gases in deep geological repositories according to the Swiss disposal concept

International Nuclear Information System (INIS)

Diomidis, N; Cloet, V.; Leupin, O.X.; Marschall, P.; Poller, A.; Stein, M.

2016-12-01

In a deep geological repository for radioactive waste, in absence of oxygen and in presence of water, corrosion of various metals and alloys will lead to the formation of hydrogen. If present, organic materials may slowly degrade and generate carbon dioxide, methane and other gaseous species. Depending on local conditions, gaseous species can be consumed by chemical reactions and by microbial activity. If the resulting rate of gas generation exceeds the rate of migration of dissolved gas molecules in the pores of the engineered barriers or the host rock, the solubility limit of the gas will eventually be exceeded and the formation of a discrete gas phase will occur. Gases could continue to accumulate until the pressure becomes sufficient to be released in gaseous form. This report deals with the evolution of gas-related processes that can influence the long-term behaviour and safety of low- and intermediate-level waste (L/ILW) and high-level waste (HLW) repositories in Opalinus Clay. The main aim is to present a synthesis of processes and phenomena related to repository-produced gases and to assess their influence on repository performance. A current overview of gas sources, reactions and interactions, generation, consumption, and transport is provided. Furthermore, current scientific understanding is used to define safety function indicators and criteria, which are employed to evaluate the potential influence of repository-generated gas on safety-relevant properties of engineered and natural barriers. The assessment of gas generation, consumption and transport is addressed separately for the HLW and the L/ILW deep geological repositories. The employed methodology, which is common for both repository types, consists of the description and quantification of the potential gas sources, which include the waste, barrier components such as disposal canisters and other gas-generating repository components, and of the processes and reactions leading to the generation or

Production, consumption and transport of gases in deep geological repositories according to the Swiss disposal concept

Energy Technology Data Exchange (ETDEWEB)

Diomidis, N; Cloet, V.; Leupin, O.X.; Marschall, P.; Poller, A.; Stein, M.

2016-12-15

In a deep geological repository for radioactive waste, in absence of oxygen and in presence of water, corrosion of various metals and alloys will lead to the formation of hydrogen. If present, organic materials may slowly degrade and generate carbon dioxide, methane and other gaseous species. Depending on local conditions, gaseous species can be consumed by chemical reactions and by microbial activity. If the resulting rate of gas generation exceeds the rate of migration of dissolved gas molecules in the pores of the engineered barriers or the host rock, the solubility limit of the gas will eventually be exceeded and the formation of a discrete gas phase will occur. Gases could continue to accumulate until the pressure becomes sufficient to be released in gaseous form. This report deals with the evolution of gas-related processes that can influence the long-term behaviour and safety of low- and intermediate-level waste (L/ILW) and high-level waste (HLW) repositories in Opalinus Clay. The main aim is to present a synthesis of processes and phenomena related to repository-produced gases and to assess their influence on repository performance. A current overview of gas sources, reactions and interactions, generation, consumption, and transport is provided. Furthermore, current scientific understanding is used to define safety function indicators and criteria, which are employed to evaluate the potential influence of repository-generated gas on safety-relevant properties of engineered and natural barriers. The assessment of gas generation, consumption and transport is addressed separately for the HLW and the L/ILW deep geological repositories. The employed methodology, which is common for both repository types, consists of the description and quantification of the potential gas sources, which include the waste, barrier components such as disposal canisters and other gas-generating repository components, and of the processes and reactions leading to the generation or

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 22. Nuclear considerations for repository design

International Nuclear Information System (INIS)

1978-04-01

This volume, Y/OWI/TM-36/22, ''Nuclear Considerations for Repository Design,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. Included in this volume are baseline design considerations such as characteristics of canisters, drums, casks, overpacks, and shipping containers; maximum allowable and actual decay-heat levels; and canister radiation levels. Other topics include safeguard and protection considerations; occupational radiation exposure including ALARA programs; shielding of canisters, transporters and forklift trucks; monitoring considerations; mine water treatment; canister integrity; and criticality calculations

Repository simulation tests

International Nuclear Information System (INIS)

Wicks, G.G.; Bibler, N.E.; Jantzen, C.M.; Plodinec, M.J.

1984-01-01

The repository simulation experiments described in this paper are designed to assess the performance of SRP waste glass under the most realistic repository conditions that can be obtained in the laboratory. These tests simulate the repository environment as closely as possible and introduce systematically the variability of the geology, groundwater chemistry, and waste package components during the leaching of the waste glass. The tests evaluate waste form performance under site-specific conditions, which differ for each of the geologic repositories under consideration. Data from these experiments will aid in the development of a realistic source term that can describe the release of radionuclides from SRP waste glass as a component of proposed waste packages. Hence, this information can be useful to optimize waste package design for SRP waste glass and to provide data for predicting long-term performance and subsequent conformance to regulations. The repository simulation tests also help to bridge the gap in interpreting results derived from tests performed under the control of the laboratory to the uncertainity and variability of field tests. In these experiments, site-specific repository components and conditions are emphasized and only the site specific materials contact the waste forms. An important feature of these tests is that both actual and simulated waste glasses are tested identically. 7 figures, 2 tables

Evaluation of geological documents available for provisional safety analyses of potential sites for nuclear waste repositories - Are additional geological investigations needed?

International Nuclear Information System (INIS)

2010-10-01

The procedure for selecting repository sites for all categories of radioactive waste in Switzerland is defined in the conceptual part of the Sectoral Plan for Deep Geological Repositories, which foresees a selection of sites in three stages. In Stage I, Nagra proposed geological siting regions based on criteria relating to safety and engineering feasibility. The Swiss Government (the Federal Council) is expected to decide on the siting proposals in 2011. The objective of Stage 2 is to prepare proposals for the location of the surface facilities within the planning perimeters defined by the Federal Council in its decision on Stage 1 and to identify potential sites. Nagra also has to carry out a provisional safety analysis for each site and a safety-based comparison of the sites. Based on this, and taking into account the results of the socio-economic-ecological impact studies, Nagra then has to propose at least two sites for each repository type to be carried through to Stage 3. The proposed sites will then be investigated in more detail in Stage 3 to ensure that the selection of the sites for the General Licence Applications is well founded. In order to realise the objectives of the upcoming Stage 2, the state of knowledge of the geological conditions at the sites has to be sufficient to perform the provisional safety analyses. Therefore, in preparation for Stage 2, the conceptual part of the Sectoral Plan requires Nagra to clarify the need for additional investigations aimed at providing input for the provisional safety analyses. The purpose of the present report is to document Nagra's technical-scientific assessment of this need. The focus is on evaluating the geological information based on processes and parameters that are relevant for safety and engineering feasibility. In evaluating the state of knowledge the key question is whether additional information could lead to a different decision regarding the selection of the sites to be carried through to Stage 3

AEGIS technology demonstration for a nuclear waste repository in basalt. Assessment of effectiveness of geologic isolation systems

International Nuclear Information System (INIS)

Dove, F.H.; Cole, C.R.; Foley, M.G.

1982-09-01

A technology demonstration of current performance assessment techniques as applied to a nuclear waste repository in the Columbia Plateau Basalts was conducted. Hypothetical repository coordinates were selected for an actual geographical setting on the Hanford Reservation in the state of Washington. Published hydrologic and geologic data used in the analyses were gathered in 1979 or earlier. The following report documents the technology demonstration in basalt. Available information has been used to establish the data base and initial hydrologic and geologic interpretations for this site-specific application. A simplified diagram of the AEGIS analyses is shown. Because an understanding of the dynamics of ground-water flow is essential to the development of release scenarios and consequence analyses, a key step in the demonstration is the systems characterization contained in the conceptual model. Regional and local ground-water movement patterns have been defined with the aid of hydrologic computer models. Hypothetical release scenarios have been developed and evaluated by a process involving expert opinion and a Geologic Simulation Model for basalt. (The Geologic Simulation Model can also be used to forecast future boundary conditions for the hydrologic simulation.) Chemical reactivity of the basalt with ground water will influence the leaching and transport of radionuclides; solubility equilibria based on available data are estimated with geochemical models. After the radionuclide concentrations are mathematically introduced into the ground-water movement patterns, waste movement patterns are outlined over elapsed time. Contaminant transport results are summarized for significant radionuclides that are hypothetically released to the accessible environment and to the biosphere

AEGIS technology demonstration for a nuclear waste repository in basalt. Assessment of effectiveness of geologic isolation systems

Energy Technology Data Exchange (ETDEWEB)

Dove, F.H.; Cole, C.R.; Foley, M.G.

1982-09-01

A technology demonstration of current performance assessment techniques as applied to a nuclear waste repository in the Columbia Plateau Basalts was conducted. Hypothetical repository coordinates were selected for an actual geographical setting on the Hanford Reservation in the state of Washington. Published hydrologic and geologic data used in the analyses were gathered in 1979 or earlier. The following report documents the technology demonstration in basalt. Available information has been used to establish the data base and initial hydrologic and geologic interpretations for this site-specific application. A simplified diagram of the AEGIS analyses is shown. Because an understanding of the dynamics of ground-water flow is essential to the development of release scenarios and consequence analyses, a key step in the demonstration is the systems characterization contained in the conceptual model. Regional and local ground-water movement patterns have been defined with the aid of hydrologic computer models. Hypothetical release scenarios have been developed and evaluated by a process involving expert opinion and a Geologic Simulation Model for basalt. (The Geologic Simulation Model can also be used to forecast future boundary conditions for the hydrologic simulation.) Chemical reactivity of the basalt with ground water will influence the leaching and transport of radionuclides; solubility equilibria based on available data are estimated with geochemical models. After the radionuclide concentrations are mathematically introduced into the ground-water movement patterns, waste movement patterns are outlined over elapsed time. Contaminant transport results are summarized for significant radionuclides that are hypothetically released to the accessible environment and to the biosphere.

Status of technology for isolating high-level radioactive wastes in geologic repositories

International Nuclear Information System (INIS)

Klingsberg, C.; Duguid, J.

1980-10-01

This report attempts to summarize the status of scientific and technological knowledge relevant to long-term isolation of high-level and transuranic wastes in a mined geologic repository. It also identifies and evaluates needed information and identifies topics in which work is under way or needed to reduce uncertainties. The major findings and conclusions on the following topics are presented: importance of the systems approach; prospects for successful isolation of wastes; need for site-specific investigations; human activities in the future; importance of modelling; disposal of transuranic wastes; status of technology of isolation barriers, performance assessment, site selection and characterization, and potential host rocks

National Geoscience Data Repository System: Phase 2 final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

The American Geological Institute (AGI) has completed Phase 2 of a project to establish a National Geoscience Data Repository System (NGDRS). The project`s primary objectives are to preserve geoscience data in jeopardy of being destroyed and to make that data available to those who have a need to use it in future investigations. These data are available for donation to the public as a result of the downsizing that has occurred in the major petroleum and mining companies in the US for the past decade. In recent years, these companies have consolidated domestic operations, sold many of their domestic properties and relinquished many of their leases. The scientific data associated with those properties are no longer considered to be useful assets and are consequently in danger of being lost forever. The national repository project will make many of these data available to the geoscience community for the first time. Phase 2 encompasses the establishment of standards for indexing and cataloging of geoscience data and determination of the costs of transferring data from the private sector to public-sector data repositories. Pilot projects evaluated the feasibility of the project for transfer of different data types and creation of a Web-based metadata supercatalog and browser. Also as part of the project, a national directory of geoscience data repositories was compiled to assess what data are currently available in existing facilities. The next step, Phase 3, will focus on the initiation of transfer of geoscience data from the private sector to the public domain and development of the web-based Geotrek metadata supercatalog.

Researching radioactive waste disposal. [Underground repository

Energy Technology Data Exchange (ETDEWEB)

Feates, F; Keen, N [UKAEA Research Group, Harwell. Atomic Energy Research Establishment

1976-02-16

At present it is planned to use the vitrification process to convert highly radioactive liquid wastes, arising from nuclear power programme, into glass which will be contained in steel cylinders for storage. The UKAEA in collaboration with other European countries is currently assessing the relative suitability of various natural geological structures as final repositories for the vitrified material. The Institute of Geological Sciences has been commissioned to specify the geological criteria that should be met by a rock structure if it is to be used for the construction of a repository though at this stage disposal sites are not being sought. The current research programme aims to obtain basic geological data about the structure of the rocks well below the surface and is expected to continue for at least three years. The results in all the European countries will then be considered so that the United Kingdom can choose a preferred method for isolating their wastes. It is only at that stage that a firm commitment may be made to select a site for a potential repository, when a far more detailed scientific research study will be instituted. Heat transfer problems and chemical effects which may occur within and around repositories are being investigated and a conceptual design study for an underground repository is being prepared.

Role of waste packages in the safety of a high level waste repository in a deep geological formation

International Nuclear Information System (INIS)

Bretheau, F.; Lewi, J.

1990-06-01

The safety of a radioactive waste disposal facility lays on the three following barriers placed between the radioactive materials and the biosphere: the waste package; the engineered barriers; the geological barrier. The function assigned to each of these barriers in the performance assessment is an option taken by the organization responsible for waste disposal management (ANDRA in France), which must show that: expected performances of each barrier (confinement ability, life-time, etc.) are at least equal to those required to fulfill the assigned function; radiation protection requirements are met in all situations considered as credible, whether they be the normal situation or random event situations. The French waste management strategy is based upon two types of disposal depending on the nature and activity of waste packages: - surface disposal intended for low and medium level wastes having half-lives of about 30 years or less and alpha activity less than 3.7 MBq/kg (0.1 Ci/t), for individual packages and less than 0.37 MBq/kg (0.01 Ci/t) in the average. Deep geological disposal intended for TRU and high level wastes. The conditions of acceptance of packages in a surface disposal site are subject to the two fundamental safety rules no. I.2 and III.2.e. The present paper is only dealing with deep geological disposal. For deep geological repositories, three stages are involved: stage preceding definitive disposal (intermediate storage, transportation, handling, setting up in the disposal cavities); stage subsequent to definitive sealing of the disposal cavities but prior to the end of operation of the repository; stage subsequent to closure of the repository. The role of the geological barrier has been determined as the essential part of long term radioactivity confinement, by a working group, set up by the French safety authorities. Essential technical criteria relating to the choice of a site so defined by this group, are the following: very low permeability

National waste terminal storage repository in a bedded salt formation for spent unreprocessed fuel. Volume I. Conceptual design report

International Nuclear Information System (INIS)

1978-12-01

In February 1976, the Energy Research and Development Administration (ERDA), now the Department of Energy (DOE), established a National Waste Terminal Storage (NWTS) program. As a part of this program, two parallel conceptual design efforts were initiated in January 1977. One was for deep geologic storage, in domed salt, of high level waste resulting from the reprocessing of spent fuel. The other was for deep geologic storage of unreprocessed spent fuel in bedded salt. These two concepts are identified as NWTS Repository 1 and Repository 2, respectively. Repository 2 (NWTSR2) is the concept which is covered by this Conceptual Design Report. Volume I of the conceptual design report contains the following information: physical description of the report; project purpose and justification; principal safety, fire, and health hazards; environmental impact considerations; quality assurance considerations; assessment of operational interfaces; assessment of research and development interfaces; project schedule; proposed method of accomplishment; summary cost estimate; and outline specifications. The conceptual design for Repository 2 was developed in sufficient detail to permit determination of scope, engineering feasibility, schedule, and cost estimates, all of which are necessary for planning and budgeting the project

Cost Comparison for the Transfer of Select Calcined Waste Canisters to the Monitored Geologic Repository at Yucca Mountain, NV

International Nuclear Information System (INIS)

Michael B. Heiser; Clark B. Millet

2005-01-01

This report performs a life-cycle cost comparison of three proposed canister designs for the shipment and disposition of Idaho National Laboratory high-level calcined waste currently in storage at the Idaho Nuclear Technology and Engineering Center to the proposed national monitored geologic repository at Yucca Mountain, Nevada. Concept A (2 x 10-ft) and Concept B (2 x 15-ft) canisters are comparable in design, but they differ in size and waste loading options and vary proportionally in weight. The Concept C (5.5 x 17.5-ft) canister (also called the ''super canister''), while similar in design to the other canisters, is considerably larger and heavier than Concept A and B canisters and has a greater wall thickness. This report includes estimating the unique life-cycle costs for the three canister designs. Unique life-cycle costs include elements such as canister purchase and filling at the Idaho Nuclear Technology and Engineering Center, cask preparation and roundtrip consignment costs, final disposition in the monitored geologic repository (including canister off-loading and placement in the final waste disposal package for disposition), and cask purchase. Packaging of the calcine ''as-is'' would save $2.9 to $3.9 billion over direct vitrification disposal in the proposed national monitored geologic repository at Yucca Mountain, Nevada. Using the larger Concept C canisters would use 0.75 mi less of tunnel space, cost $1.3 billion less than 10-ft canisters of Concept A, and would be complete in 6.2 years

Experiments on thermal conductivity in buffer materials for geologic repository

International Nuclear Information System (INIS)

Kanno, T.; Yano, T.; Wakamatsu, H.; Matsushima, E.

1989-01-01

Engineered barriers for geologic disposal for HLW are planned to consist of canister, overpack and buffer elements. One of important physical characteristics of buffer materials is determining temperature profiles within the near field in a repository. Buffer materials require high thermal conductivity to disperse radiogenic heat away to the host rock. As the buffer materials, compacted blocks of the mixture of sodium bentonite and sand have been the most promising candidate in some countries, e.g. Sweden, Switzerland and Japan. The authors have been carrying out a series of thermal dispersion experiments to evaluate thermal conductivity of bentonite/quartz sand blocks. In this study, the following two factors considered to affect thermal properties of the near field were examined: effective thermal conductivities of buffer materials, and heat transfer characteristics of the gap between overpack and buffer materials

Dealing with uncertainties in the safety of geological disposal of radioactive waste

International Nuclear Information System (INIS)

Devillers, Ch.

2002-01-01

Confidence in the safety assessment of a possible project of radioactive waste geological repository will only be obtained if the development of the project is closely guided by transparent safety strategies, acknowledging uncertainties and striving for limiting their effects. This paper highlights some sources of uncertainties, external or internal to the project, which are of particular importance for safety. It suggests safety strategies adapted to the uncertainties considered. The case of a possible repository project in the Callovo-Oxfordian clay layer of the French Bure site is examined from that point of view. The German project at Gorleben and the Swedish KBS-3 project are also briefly examined. (author)

The project ANSICHT. Safety and demonstration methodology for a final repository in clay formations in Germany; Projekt ANSICHT. Sicherheits- und Nachweismethodik fuer ein Endlager im Tongestein in Deutschland. Synthesebericht

Energy Technology Data Exchange (ETDEWEB)

Jobmann, Michael; Bebiolka, Anke; Jahn, Steffen; and others

2017-03-30

Based on the status of science and technology and under consideration of international repository concepts the fundamental methodology for safety demonstration for a high-level radioactive waste final repository in clay formations Germany was developed. Basic elements of the safety concept are the geological site description and the geo-scientific long-term prognosis on future performance. Another important section is the closure and sealing concept for the mine shafts. In the frame of the project the fundamental elements were developed and documented for model regions in northern and southern Germany. Three independent safety proofs have to be performed: the demonstration of the geological barrier integrity (clay), the demonstration of the geo-technical barrier system integrity - i.e. closure constructions and backfilling of the shafts, and the radiological demonstration that the radionuclide release in the area is lower than the respective limiting value.

Bedrock geologic map of the central block area, Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

Day, W.C.; Potter, C.J.; Sweetkind, D.S.; Dickerson, R.P.; San Juan, C.A.

1998-01-01

Bedrock geologic maps form the foundation for investigations that characterize and assess the viability of the potential high-level radioactive waste repository at Yucca Mountain, Nevada. This study was funded by the US Department of Energy Yucca Mountain Project to provide a detailed (1:6,000-scale) bedrock geologic map for the area within and adjacent to the potential repository area at Yucca Mountain, Nye County, Nevada. Prior to this study, the 1:12,000-scale map of Scott and Bon, (1984) was the primary source of bedrock geologic data for the Yucca Mountain Project. However, targeted detailed mapping within the central block at Yucca Mountain revealed structural complexities along some of the intrablock faults that were not evident at 1:12,000 (Scott and Bonk, 1984). As a result, this study was undertaken to define the character and extent of the dominant structural features in the vicinity of the potential repository. In addition to structural considerations, ongoing subsurface excavation and geologic mapping within the exploratory Studies Facility (ESF), development of a three-dimensional-framework geologic model, and borehole investigations required use of a constituent stratigraphic system to facilitate surface to underground comparisons. The map units depicted in this report correspond as closely as possible to the proposed stratigraphic nomenclature by Buesch and others (1996), as described here

Reference repository design concept for bedded salt

Energy Technology Data Exchange (ETDEWEB)

Carpenter, D.W.; Martin, R.W.

1980-10-08

A reference design concept is presented for the subsurface portions of a nuclear waste repository in bedded salt. General geologic, geotechnical, hydrologic and geochemical data as well as descriptions of the physical systems are provided for use on generic analyses of the pre- and post-sealing performance of repositories in this geologic medium. The geology of bedded salt deposits and the regional and repository horizon stratigraphy are discussed. Structural features of salt beds including discontinuities and dissolution features are presented and their effect on repository performance is discussed. Seismic hazards and the potential effects of earthquakes on underground repositories are presented. The effect on structural stability and worker safety during construction from hydrocarbon and inorganic gases is described. Geohydrologic considerations including regional hydrology, repository scale hydrology and several hydrological failure modes are presented in detail as well as the hydrological considerations that effect repository design. Operational phase performance is discussed with respect to operations, ventilation system, shaft conveyances, waste handling and retrieval systems and receival rates of nuclear waste. Performance analysis of the post sealing period of a nuclear repository is discussed, and parameters to be used in such an analysis are presented along with regulatory constraints. Some judgements are made regarding hydrologic failure scenarios. Finally, the design and licensing process, consistent with the current licensing procedure is described in a format that can be easily understood.

Reference repository design concept for bedded salt

International Nuclear Information System (INIS)

Carpenter, D.W.; Martin, R.W.

1980-01-01

A reference design concept is presented for the subsurface portions of a nuclear waste repository in bedded salt. General geologic, geotechnical, hydrologic and geochemical data as well as descriptions of the physical systems are provided for use on generic analyses of the pre- and post-sealing performance of repositories in this geologic medium. The geology of bedded salt deposits and the regional and repository horizon stratigraphy are discussed. Structural features of salt beds including discontinuities and dissolution features are presented and their effect on repository performance is discussed. Seismic hazards and the potential effects of earthquakes on underground repositories are presented. The effect on structural stability and worker safety during construction from hydrocarbon and inorganic gases is described. Geohydrologic considerations including regional hydrology, repository scale hydrology and several hydrological failure modes are presented in detail as well as the hydrological considerations that effect repository design. Operational phase performance is discussed with respect to operations, ventilation system, shaft conveyances, waste handling and retrieval systems and receival rates of nuclear waste. Performance analysis of the post sealing period of a nuclear repository is discussed, and parameters to be used in such an analysis are presented along with regulatory constraints. Some judgements are made regarding hydrologic failure scenarios. Finally, the design and licensing process, consistent with the current licensing procedure is described in a format that can be easily understood

Tunnel Boring Machine for nuclear waste repository research project

International Nuclear Information System (INIS)

Janzon, H.A.

1994-01-01

A description is presented of a Tunnel Boring Machine and its intended use on a research project underway in Sweden for demonstrating and testing methods for rock investigation at a suitable depth for a deep repository for nuclear waste

Integrated management system for radioactive waste repositories (SGI3R)

International Nuclear Information System (INIS)

Silva, Fabio; Tello, Cledola Cassia Oliveira de

2009-01-01

The implantation of a repository for radioactive wastes is a multidisciplinary project that needs specialists of different areas of knowledge, interaction with public and private institutions, data and information related to radioactive wastes, geology, technology etc. All the activities must be in accordance with norms, requirements and procedures, including national and international legislation. The maintenance of the waste inventory records is an important regulatory requirement and must be available even after the closure of the repository. CDTN - Center of Nuclear Technology Development - is coordinating the Project for the construction of the national repository to dispose the low -and intermediate-level wastes. In order to consolidate all information that will come from this Project, it is being developed and implanted in CDTN a manager system of database, called Integrated Management System for Radioactive Waste Repositories (SGI3R), which will also manage all data from previous work carried out in Brazil and around the world about this subject. The proposal is to build a structure of modules, having as base eight modules: inventory, site selection, types of repository, technology, partners, legislation, communication and documents. The SGI3R running comprises the data processing (inclusion, update and exclusion), integration, standardization, and consistency among the processes. The SGI3R will give support to the stages of this Project, which will allow the preservation of all the available information, preventing duplication of efforts and additional costs, improving, in this way, the Project planning and execution. Additionally the SGI3R will make possible the information access to all stakeholders. (author)

Waste package transfer, emplacement and retrievability in the French deep geological repository

Energy Technology Data Exchange (ETDEWEB)

Roulet, Alain; Delort, Daniel; Herve, Jean Francois; Bosgiraud, Jean Michel; Guenin, Jean Jacques [Technical Department ANDRA (France)

2009-06-15

Safe, reliable and reversible handling of waste is a significant issue related to the design and safety assessment of deep geological repository in France. The first step taken was to study various waste handling solutions. ANDRA also decided to fabricate and demonstrate industrial scale handling equipment for HLW (since 2003) and for ILW-LL wastes (since 2008). We will review the main equipment developed for the transfer process in the repository, for both types of waste, and underline the benefits of developing industrial demonstrators within the framework of international cooperation agreements. Waste retrieval capability will be simultaneously examined. Two types of waste have to be handled underground in Andra's repository. The HLW disposal package for vitrified waste is a 2 ton carbon steel cylindrical canister with a diameter of 600 mm. The weight of ILW-LL concrete disposal packages range from a minimum of 6 tonnes to over 20 tonnes, and their volume from approximately 5 to 10 m3. The underground transfer to the disposal drift requires moving the disposal package within a shielded transfer cask placed on a trailer. Transfer cask design has evolved since 2005, due to optimisation studies and as a result of industrial feedback from SKB. For HLW handling equipment two design options have been studied. In the first solution (Andra's Dossier 2005), the waste package are emplaced, one at a time, in the disposal drift by a pushing robot. Successive steps in design and proto-typing have lead to improve the design of the equipment and to gain confidence. Recently a fully integrated process has been successfully demonstrated, at full scale, (in a 100 m long mock up drift) as part of the EC funded ESDRED Project. This demonstrator is now on display in Andra's Technology Centre at Saudron, near the Bure Underground Laboratory. The second disposal option which has been investigated is based on a concept of utilising an external apparatus to push a row of

Response to state comments on the revised draft North Central Regional characterization reports for the Crystalline Repository Project

International Nuclear Information System (INIS)

1985-08-01

The purpose of this document is to respond to the comments received from the states of the North Central Region on the revised draft North Central Regional Characterization Reports (RCRs). The responses in this document indicate the manner in which the suggestions or comments received have been considered in modifying the revised draft North Central RCRs. Both general comments related to the overall Crystalline Repository Project (CRP) and comments on specific sections of the RCRs are addressed. This document responds to North Central State comments on both the revised draft North Central Regional Geologic Characterization Report (RGCR) and the revised draft North Central Regional Environmental Characterization Report (RECR)

Reference Design Description for a Geologic Repository, Rev. 03, ICN 02

International Nuclear Information System (INIS)

Gerald Shideler

2001-01-01

One of the current major national environmental problems is the safe disposal of large quantities of spent nuclear fuel and high-level radioactive waste materials, which are rapidly accumulating throughout the country. These radioactive byproducts are generated as the result of national defense activities and from the generation of electricity by commercial nuclear power plants. At present, spent nuclear fuel is accumulating at over 70 power plant sites distributed throughout 33 states. The safe disposal of these high-level radioactive materials at a central disposal facility is a high national priority. This Reference Design Description explains the current design for a potential geologic repository that may be located at Yucca Mountain in Nevada for the disposal of spent nuclear fuel and high-level radioactive waste materials. This document describes a possible design for the three fundamental parts of a repository: a surface facility, subsurface repository, and waste packaging. It also presents the current conceptual design of the key engineering systems for the final four phases of repository processes: operations, monitoring, closure, and postclosure. In accordance with current law, this design does not include an interim storage option. In addition, this Reference Design Description reviews the expected long-term performance of the potential repository. It describes the natural barrier system which, together with the engineered systems, achieves the repository objectives. This design will protect the public and the environment by allowing the safe disposal of radioactive waste received from government-owned custodial spent fuel sites, high-level radioactive waste sites, and commercial power reactor sites. All design elements meet or exceed applicable regulations governing the disposal of high-level radioactive waste. The design will provide safe disposal of waste materials for at least a 10,000 year period. During this time interval, natural radioactive decay

Area Recommendation Report for the Crystalline Repository Project: Volume 1, Draft

International Nuclear Information System (INIS)

1986-01-01

This Draft Area Recommendation Report for the Crystalline Repository Project identifies portions of crystalline rock bodies as proposed potentially acceptable sites for consideration in the second high-level radioactive waste repository program. The US Department of Energy evaluated available geologic and environmental data for 235 crystalline rock bodies in the North Central, Northeastern, and Southeastern regions to identify preliminary candidate areas. Further evaluation of these preliminary candidate areas resulted in the selection of 12 as proposed potentially acceptable sites. The 12 proposed potentially acceptable sites are located in the States of Georgia (1), Maine (2), Minnesota (3), New Hampshire (1), North Carolina (2), Virginia (2), and Wisconsin (1). The data, analyses, and rationale with which the 12 proposed potentially acceptable sites were selected are presented in this draft report. The analyses presented demonstrate that the evidence available for each proposed potentially acceptable site supports (1) a finding that the site is not disqualified in accordance with the application requirements of Appendix III of the siting guidelines and (2) a decision to proceed with the continued investigation of the site on the basis of the favorable and potentially adverse conditions identified to date. Once this report is finalized, potentially acceptable sites in crystalline rock will be formally identified by the Secretary of Energy, in accordance with the DOE siting guidelines. These potentially acceptable sites will be investigated and evaluated in more detail during the area phase of the siting process. An additional eight areas, which meet the requirements for identification as potentially acceptable sites, will retain their designation as candidate areas

Ontario Power Generation's proposed L and ILW deep geologic repository: geo-scientific assessment

International Nuclear Information System (INIS)

Jensen, Mark; Raven, Ken; Leech, Robert

2012-01-01

Document available in extended abstract form only. The Nuclear Waste Management Organization (NWMO) on behalf of Ontario Power Generation (OPG) has conducted multi-disciplinary geo-scientific studies at the Bruce nuclear site to confirm the suitability of the site to host a proposed Deep Geologic Repository (DGR) for the long-term management of Low and Intermediate Level Radioactive Waste (L and ILW) from OPG owned or operated nuclear generating facilities. An Environmental Assessment for the proposed DGR is currently underway in accordance with the Canadian Environmental Assessment Act. Bruce nuclear site, situated 225 km northwest of Toronto on the eastern shore of Lake Huron, is underlain by an 850 m thick sedimentary sequence of Cambrian to Devonian age near-horizontally layered, weakly deformed shales, carbonates and evaporites of the Michigan Basin. Within this sedimentary pile, the proposed DGR would be excavated within the low permeability argillaceous limestone of the Cobourg Formation at a depth of 680 m, which is overlain by 200 m of Upper Ordovician shale formations (Figure 1). A key aspect of the DGR Safety Case is the predictable nature and long-term stability and integrity of the sedimentary sequence to contain and isolate L and ILW at time frames on the order of 1 Ma. Early in the project, geo-scientific studies that considered regional and site-specific public domain data sets indicated favourable geologic conditions for implementation of the DGR concept (Golder, 2003; Mazurek, 2004). Geo-scientific studies for the DGR were initiated in 2006 following decision by the Municipality of Kincardine to support the DGR concept. Geo-scientific activities were divided into two key areas; i) Site-specific geo-scientific studies of the Bruce nuclear site (i.e., Descriptive Geosphere Site Model); and ii) a Geo-synthesis to convey an understanding of past, present and future evolution of Geosphere enclosing the DGR relevant to communicating notions of

Modeling of irradiated graphite {sup 14}C transfer through engineered barriers of a generic geological repository in crystalline rocks

Energy Technology Data Exchange (ETDEWEB)

Poskas, Povilas; Grigaliuniene, Dalia, E-mail: Dalia.Grigaliuniene@lei.lt; Narkuniene, Asta; Kilda, Raimondas; Justinavicius, Darius

2016-11-01

There are two RBMK-1500 type graphite moderated reactors at the Ignalina nuclear power plant in Lithuania, and they are under decommissioning now. The graphite cannot be disposed of in a near surface repository, because of large amounts of {sup 14}C. Therefore, disposal of the graphite in a geological repository is a reasonable solution. This study presents evaluation of the {sup 14}C transfer by the groundwater pathway into the geosphere from the irradiated graphite in a generic geological repository in crystalline rocks and demonstration of the role of the different components of the engineered barrier system by performing local sensitivity analysis. The speciation of the released {sup 14}C into organic and inorganic compounds as well as the most recent information on {sup 14}C source term was taken into account. Two alternatives were considered in the analysis: disposal of graphite in containers with encapsulant and without it. It was evaluated that the maximal fractional flux of inorganic {sup 14}C into the geosphere can vary from 10{sup −} {sup 11} y{sup −} {sup 1} (for non-encapsulated graphite) to 10{sup −} {sup 12} y{sup −} {sup 1} (for encapsulated graphite) while of organic {sup 14}C it was about 10{sup −} {sup 3} y{sup −} {sup 1} of its inventory. Such difference demonstrates that investigations on the {sup 14}C inventory and chemical form in which it is released are especially important. The parameter with the highest influence on the maximal flux into the geosphere for inorganic {sup 14}C transfer was the sorption coefficient in the backfill and for organic {sup 14}C transfer – the backfill hydraulic conductivity. - Highlights: • Graphite moderated nuclear reactors are being decommissioned. • We studied interaction of disposed material with surrounding environment. • Specifically {sup 14}C transfer through engineered barriers of a geological repository. • Organic {sup 14}C flux to geosphere is considerably higher than inorganic

Operational procedures for receiving, packaging, emplacing, and retrieving high-level and transuranic waste in a geologic repository in TUFF

International Nuclear Information System (INIS)

Dennis, A.W.; Mulkin, R.

1984-01-01

The Nevada Nuclear Waste Storage Investigations Project, directed by the Nevada Operations Office of the Department of Energy, is currently developing conceptual designs for a commercial nuclear waste repository. In this paper, the preliminary repository operating plans are identified and the proposed repository waste inventory is discussed. The receipt rates for truck and rail car shipments of waste are determined as are the required repository waste emplacement rates

MRS system study for the repository: Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Sinagra, T.A.; Harig, R.

1990-12-01

The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), has initiated a waste management system study to identify the impacts of the presence or absence of a monitored retrievable storage facility (hereinafter referred to as ''MRS'') on system costs and program schedules. To support this study, life-cycle cost estimates and construction schedules have been prepared for the surface and underground facilities and operations geologic nuclear waste repository at Yucca Mountain, Nye County, Nevada. Nine different operating scenarios (cases) have been identified by OCRWM for inclusion in this study. For each case, the following items are determined: the repository design and construction costs, operating costs, closure and decommissioning costs, required staffing, construction schedules, uncertainties associated with the costs and schedules, and shipping cask and disposal container throughputs. This document contains A-D

MRS system study for the repository: Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Sinagra, T.A.; Harig, R.

1990-12-01

The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), has initiated a waste management system study to identify the impacts of the presence or absence of a monitored retrievable storage facility (hereinafter referred to as ''MRS'') on system costs and program schedules. To support this study, life-cycle cost estimates and construction schedules have been prepared for the surface and underground facilities and operations of a geologic nuclear waste repository at Yucca Mountain, Nye County, Nevada. Nine different operating scenarios (cases) have been identified by OCRWM for inclusion in this study. For each case, the following items are determined: the repository design and construction costs, operating costs, closure and decommissioning costs, required staffing, construction schedules, uncertainties associated with the costs and schedules, and shipping cask and disposal container throughputs. 6 refs., 83 figs., 57 tabs

Cesium and strontium fractionation from HLW for thermal-stress reduction in a geologic repository

International Nuclear Information System (INIS)

McKee, R.W.

1983-02-01

Results are described for a study to assess the benefits and costs of fractionating the cesium and strontium components in commercial high-level waste (HLW) to a separate waste stream for the purpose of reducing geologic repository thermal stresses. System costs are developed for a broad range of conditions comparing the Cs/Sr fractionation concept with disposal of 10-year old vitrified HLW and vitrified HLW aged to achieve (through decay) the same heat output as the fractionated high-level waste (FHLW). All comparisons are based on a 50,000 metric ton equivalent (MTE) system. The FHLW and the Cs/Sr waste are both disposed of a vitrified waste but emplaced in separate areas of a basalt repository. The FHLW is emplaced in high-integrity packages at relatively high waste loading but low heat loading, while the Cs/Sr waste is emplaced in minimum integrity packages at relatively high heat loading. System cost comparisons are based on minimum cost combinations of canister diameter, waste concentration, and canister spacing in a basalt repository for each waste type. The effects on both long- and near-term safety considerations are also addressed. The major conclusion is that the Cs/Sr fractionation concept offers, potentially, a substantial total system cost advantage for HLW disposal if reduced HLW package temperatures in a basalt repository are desired. However, there is no cost advantage if currently designated maximum design temperatures are acceptable. Aging the HLW for 50 to 100 years can accomplish similar results at equivalent or loser costs

Interim performance specifications for conceptual waste-package designs for geologic isolation in salt repositories

International Nuclear Information System (INIS)

1983-06-01

The interim performance specifications and data requirements presented apply to conceptual waste package designs for all waste forms which will be isolated in salt geologic repositories. The waste package performance specifications and data requirements respond to the waste package performance criteria. Subject areas treated include: containment and controlled release, operational period safety, criticality control, identification, and waste package performance testing requirements. This document was generated for use in the development of conceptual waste package designs in salt. It will be revised as additional data, analyses, and regulatory requirements become available

Repositories; Repositorios

Energy Technology Data Exchange (ETDEWEB)

Freire, Carolina Braccini; Tello, Cledola Cassia Oliveira de [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mails: cbf@cdtn.br; tellocc@cdtn.br

2007-11-15

The use of the nuclear energy is increasing in all areas. Then the radioactive waste management is in continuous development to comply the national and international established requirements. The final objective is to assure that it will not have any contamination of the public or the environmental, and that the exposition doses will be lower than the radiological protection limits. The multi barrier concept for the repository is internationally recognized. Among the repository types, the most used are: near surface, geological formations and of deposition in rock cavities. This article explains the concept and the types of repository and gives some examples of them. (author)

International Approaches for Nuclear Waste Disposal in Geological Formations: Geological Challenges in Radioactive Waste Isolation—Fifth Worldwide Review

Energy Technology Data Exchange (ETDEWEB)

Faybishenko, Boris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Birkholzer, Jens [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sassani, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Swift, Peter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-04-26

The overall objective of the Fifth Worldwide Review (WWR-5) is to document the current state-of-the-art of major developments in a number of nations throughout the World pursuing geological disposal programs, and to summarize challenging problems and experience that have been obtained in siting, preparing and reviewing cases for the operational and long-term safety of proposed and operating nuclear waste repositories. The scope of the Review is to address current specific technical issues and challenges in safety case development along with the interplay of technical feasibility, siting, engineering design issues, and operational and post-closure safety. In particular, the chapters included in the report present the following types of information: the current status of the deep geological repository programs for high level nuclear waste and low- and intermediate level nuclear waste in each country, concepts of siting and radioactive waste and spent nuclear fuel management in different countries (with the emphasis of nuclear waste disposal under different climatic conditions and different geological formations), progress in repository site selection and site characterization, technology development, buffer/backfill materials studies and testing, support activities, programs, and projects, international cooperation, and future plans, as well as regulatory issues and transboundary problems.

Plugs for deposition tunnels in a deep geologic repository in granitic rock. Concepts and experience

International Nuclear Information System (INIS)

Dixon, D. A.; Boergesson, L.; Gunnarsson, D.; Hansen, J.

2009-11-01

Regardless of the emplacement geometry selected in a geological repository for spent nuclear fuel, there will be a requirement for the access tunnels to remain open while repository operations are ongoing. The period of repository operation will stretch for many years (decades to more than a century depending on disposal concept and number of canisters to be installed). Requirements for extended monitoring of the repository before final closure may further extend the period over which the tunnels must remain open. The intersection of the emplacement rooms/drifts and the access tunnels needs to be physically closed in order to ensure that the canisters remain undisturbed and that no undesirable hydraulic conditions are allowed to develop within the backfilled volume. As a result of these requirements, generic guidelines and design concepts have been developed for 'Plugs' that are intended to provide mechanical restraint, physical security and hydraulic control functions over the short-term (repository operational and pre-closure monitoring periods). This report focuses on the role and requirements of plugs to be installed at emplacement room/ tunnel/drift entrances or in other locations within the repository that may require installation of temporary mechanical or hydraulic control structures. These plugs are not necessarily a permanent feature of the repository and may, if required, be removed for later installation of a permanent seal. Room/Drift plugs are also by their defined function, physically accessible during repository operation so their performance can be monitored and remedial actions taken if necessary (e.g. increased seepage past the plug). A considerable number of sealing demonstrations have been undertaken at several research laboratories that are focussed on development of technologies and materials for use in isolation of spent nuclear fuel and these are briefly reviewed in this report. Additionally, technologies developed for non

Plugs for deposition tunnels in a deep geologic repository in granitic rock. Concepts and experience

Energy Technology Data Exchange (ETDEWEB)

Dixon, D.A. (AECL, Chalk River (Canada)); Boergesson, L. (Clay Technology, Lund (Sweden)); Gunnarsson, D. (Swedish Nuclear Fuel and Waste Management Co, Stockholm (Sweden)); Hansen, J. (Posiva Oy, Eurajoki (Finland))

2009-11-15

Regardless of the emplacement geometry selected in a geological repository for spent nuclear fuel, there will be a requirement for the access tunnels to remain open while repository operations are ongoing. The period of repository operation will stretch for many years (decades to more than a century depending on disposal concept and number of canisters to be installed). Requirements for extended monitoring of the repository before final closure may further extend the period over which the tunnels must remain open. The intersection of the emplacement rooms/drifts and the access tunnels needs to be physically closed in order to ensure that the canisters remain undisturbed and that no undesirable hydraulic conditions are allowed to develop within the backfilled volume. As a result of these requirements, generic guidelines and design concepts have been developed for 'Plugs' that are intended to provide mechanical restraint, physical security and hydraulic control functions over the short-term (repository operational and pre-closure monitoring periods). This report focuses on the role and requirements of plugs to be installed at emplacement room/ tunnel/drift entrances or in other locations within the repository that may require installation of temporary mechanical or hydraulic control structures. These plugs are not necessarily a permanent feature of the repository and may, if required, be removed for later installation of a permanent seal. Room/Drift plugs are also by their defined function, physically accessible during repository operation so their performance can be monitored and remedial actions taken if necessary (e.g. increased seepage past the plug). A considerable number of sealing demonstrations have been undertaken at several research laboratories that are focussed on development of technologies and materials for use in isolation of spent nuclear fuel and these are briefly reviewed in this report. Additionally, technologies developed for non

Assessment of Effectiveness of Geologic Isolation Systems: REFERENCE SITE INITIAL ASSESSMENT FOR A SALT DOME REPOSITORY

Energy Technology Data Exchange (ETDEWEB)

Harwell, M. A.; Brandstetter, A.; Benson, G. L.; Raymond, J. R.; Brandley, D. J.; Serne, R. J.; Soldat, J. K.; Cole, C. R.; Deutsch, W. J.; Gupta, S. K.; Harwell, C. C.; Napier, B. A.; Reisenauer, A. E.; Prater, L. S.; Simmons, C. S.; Strenge, D. L.; Washburn, J. F.; Zellmer, J. T.

1982-06-01

As a methodology demonstration for the Office of Nuclear Waste Isolation (ONWI), the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program conducted an initial reference site analysis of the long-term effectiveness of a salt dome repository. The Hainesville Salt Dome in Texas was chosen to be representative of the Gulf Coast interior salt domes; however, the Hainesville Site has been eliminated as a possible nuclear waste repository site. The data used for this exercise are not adequate for an actual assessment, nor have all the parametric analyses been made that would adequately characterize the response of the geosystem surrounding the repository. Additionally, because this was the first exercise of the complete AEGIS and WASTE Rock Interaction Technology (WRIT) methodology, this report provides the initial opportunity for the methodology, specifically applied to a site, to be reviewed by the community outside the AEGIS. The scenario evaluation, as a part of the methodology demonstration, involved consideration of a large variety of potentially disruptive phenomena, which alone or in concert could lead to a breach in a salt dome repository and to a subsequent transport of the radionuclides to the environment. Without waste- and repository-induced effects, no plausible natural geologic events or processes which would compromise the repository integrity could be envisioned over the one-million-year time frame after closure. Near-field (waste- and repository-induced) effects were excluded from consideration in this analysis, but they can be added in future analyses when that methodology development is more complete. The potential for consequential human intrusion into salt domes within a million-year time frame led to the consideration of a solution mining intrusion scenario. The AEGIS staff developed a specific human intrusion scenario at 100 years and 1000 years post-closure, which is one of a whole suite of possible scenarios. This scenario

Design information verification (DIV) of closed geological repositories (SAGOR activity 3c)

International Nuclear Information System (INIS)

Myatt, J.

1998-02-01

Following IAEA Advisory and Consultants Group meetings in September 1988 and in May 1991 respectively an IAEA multi-national Support Programme Task was initiated to consider the 'Development of Safeguards for Final Disposal of Spent Fuel in Geological Repositories' (SAGOR). A 'Technical Coordination Committee' (TCC) was set up with invited representatives from those Member State Support Programmes wishing to be involved. The joint programme, through the TCC, was given the task of studying the safeguards requirements in: conditioning plant (where the spent fuel is prepared for transfer to the repository); operating repositories (i.e. those in which the fuel is being emplaced); closed repositories. At the first meeting of the TCC in Washington in July 1994 the UK undertook to provide a study of the Design Information Verification (DIV) required in all three areas. For this activity the requirements, techniques and procedures for the Design Information Verification (DIV) of closed repositories have been considered. In completing the study the findings reported for activities 1b/c and 2c (descriptions of a Model Repository and Potential Diversion Paths, respectively) have been used in formulating any conclusions reached. It is also debatable as to whether this activity is strictly speaking DIV or is one of surveillance. As undeclared access can only be made to the emplacement areas of the repository by altering the physical makeup of the surrounding area; i.e. physically changing the 'design' of the surrounding area, however, this is deemed to be DIV. Although the techniques used appear to be those of surveillance they are being applied in this case as the tools of DIV. As with any facility there are a number of stages in its lifetime. For the purposes of this report the operating life of a repository is defined as being the time from inception to when it is finally decommissioned and sealed with the ground surface returned to being a green field. The repository is

Postclosure safety assessment of a deep geological repository for Canada's used nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Hunt, N.G.; Kremer, E.P.; Garisto, F.; Gierszewski, P.; Gobien, M.; Medri, C.L.D. [Nuclear Waste Management Organization, Toronto, ON (Canada); Avis, J.D. [Geofirma Engineering Ltd., Ottawa, ON (Canada); Chshyolkova, T.; Kitson, C.I.; Melnyk, W.; Wojciechowski, L.C. [Atomic Energy of Canada Limited, Pinawa, MB (Canada)

2011-07-01

This paper reports on elements of a postclosure safety assessment performed for a conceptual design and hypothetical site for a deep geological repository for Canada's used nuclear fuel. Key features are the assumption of a copper used fuel container with a steel inner vessel, container placement in vertical in-floor boreholes, a repository depth of 500 m, and a sparsely fractured crystalline rock geosphere. The study considers a Normal Evolution Scenario together with a series of Disruptive Event Scenarios. The Normal Evolution Scenario is a reasonable extrapolation of present day site features and receptor lifestyles, while the Disruptive Event Scenarios examine abnormal and unlikely failures of the containment and isolation systems. Both deterministic and probabilistic simulations were performed. The results show the peak dose consequences occur far in the future and are well below the applicable regulatory acceptance criteria and the natural background levels. (author)

Preparing for Construction and Operation of Geological Repositories - Challenges to the Regulator and the Implementer. Proceedings of the Joint RF/IGSC Workshop, Issy-les-Moulineaux, France, 25-27 January 2012

International Nuclear Information System (INIS)

2014-01-01

More radioactive waste management programmes are advancing to a new repository development phase and are preparing for the application of their construction license of a deep geological disposal facility. Such developmental progress brought along significant changes to repository development affecting both the waste management programme implementers and the regulators. New issues impacting both the regulatory authorities and the future facility operators include operational safety and reliability, increased demands on human resources, activities to ensure quality assurance, the additional requirements on information management system and management plans for construction work. To respond to new arising issues, the Radioactive Waste Management Committee (RWMC) of the OECD Nuclear Energy Agency (NEA) has agreed, as stated in the 2011-2016 Strategic Plan, that the Committee will focus on constituencies for the preparation of the construction and operation license of future deep geological repositories. In addition, the Committee will consider operational aspects of repository implementation, both connected to the operational safety and the impact on the post-closure long-term safety. In particular, the RWMC has approved the RWMC Regulator's Forum (RWMC-RF) and the Integration Group for the Safety Case (IGSC) to hold a joint workshop to explore challenging issues and practices in preparing for the application of the construction license of a geological repository. The joint workshop titled 'Preparing for Construction and Operation of Geological Repositories - Challenges to the Regulator and the Implementer' was held on January 25-27, 2012 at the NEA premises in Issy-les-Moulineaux, France. The key objective of the workshop was to identify, and exchange experience on, the current and future challenges faced by the implementers and the regulators when preparing for their application of a construction license of a geological repository. The workshop gave a

The FORGE (Fate Of Repository Gases) pan European project

International Nuclear Information System (INIS)

Shaw, Richard

2010-01-01

Document available in extended abstract form only. Full text of publication follows: The multiple barrier concept is the cornerstone of all proposed schemes for underground disposal of radioactive wastes. The concept invokes a series of barriers, both engineered and natural, between the waste and the surface. Achieving this concept is the primary objective of all disposal programmes, from site appraisal and characterisation to repository design and construction. However, the performance of the repository as a whole (waste, buffer, engineering disturbed zone, host rock), and in particular its gas transport properties, are still poorly understood. Issues still to be adequately examined that relate to understanding basic processes include: dilational versus visco-capillary flow mechanisms; long-term integrity of seals, in particular gas flow along contacts; role of the EDZ as a conduit for preferential flow; laboratory to field up-scaling. Understanding gas generation and migration is thus vital in the quantitative assessment of repositories and is the focus of the research in this proposal for an integrated, multidisciplinary project. The FORGE project is a pan-European project with links to international radioactive waste management organisations, regulators and academia, specifically designed to tackle the key research issues associated with the generation and movement of repository gasses with partners from 24 organisations in 12 European countries. It is supported by funding under the European Commission FP7 Euratom programme and runs from 2009 to 2013. Of particular importance are the long-term performance of bentonite buffers, plastic clays, indurated mud-rocks and crystalline formations. Further experimental data are required to reduce uncertainty relating to the quantitative treatment of gas in performance assessment. FORGE will address these issues through a series of laboratory and field-scale experiments, including the development of new methods for up

Selection of the situations taken into account for the safety demonstration of a repository in deep geological formations - French regulatory guidance and IPSN modelling experience

International Nuclear Information System (INIS)

Escalier des Orres, P.; Greneche, D.

1993-01-01

A regulatory guidance has been recently set up in France for the safety assessment of radwaste deep geological disposal: the present paper deals with the methodology related to the safety demonstration of such a disposal, particularly the situations to be taken into account to address the potential evolution of the repository under natural or human induced events. This approach, based on a selection of events considered as reasonably envisageable, relies on a reference scenario characterized by a great stability of the geological formation and on hypothetical situations corresponding to the occurrence of random events of natural origin or of conventional nature. The implementation of this methodology within the framework of the IPSN (Protection and Nuclear Safety Institute, CEA) participation in the CEC EVEREST project is addressed. This programme consists in the evaluation of the sensitivity of the radiological consequences associated to deep radwaste disposal systems to the different elements of the performance assessment (scenario characteristics, phenomena, physico-chemical parameters) in three types of geological formations (granite, salt and clay).(author). 11 refs., 3 tabs

The Yucca Mountain Repository - Too Little, Too Late

International Nuclear Information System (INIS)

Eriksson, L.G.; Pentz, D.L.

2009-01-01

In 2008, the U.S. Department of Energy (US DOE) announced that the nation's first (and only pursued) deep geological disposal system (repository) for 70,000 metric tonnes of spent nuclear fuel (SNF) and other high-level radioactive waste (HLW) at the Yucca Mountain (YM) site in Nevada would: 1. Not be able to accommodate the projected stockpile of utility-generated SNF beyond 2010. 2. Open no earlier than in 2020, i.e., more than 22 years behind the statutory-mandated opening date. In the meantime, the US DOE is legally obligated to compensate the utilities from January 31, 1998, until it takes title to the utilities' SNF. In 2005 when the YM SNF repository was projected to open in 2010, the utilities estimated that, depending upon how close to 2010 the YM repository opened, the 'breach-of-contract' compensation could be in the range of between 100 billion and 300 billion U.S. dollars ($300 B), which would exceed the 2008 projected life-cycle cost of $96 B for the YM repository. It thus seems appropriate to look beyond the YM repository and call upon the U.S. Congress to promptly act and open new avenues allowing the US DOE to more timely and cost-effectively take title to both existing and pending SNF the current fleet of 104 reactors will generate through the next 60 years. Options for SNF arising from an additional 50 reactors should also be provided. Based on our more than 60 years of combined involvement in nuclear waste management in the USA and abroad, we submit the following industrial-scale-proven, repository-related, nuclear-waste-management and disposition solutions for prompt Congressional consideration and action: 1. An increase in the disposal capacity (and perhaps mission) of the YM repository. 2. Prompt establishment of at least one large federal monitored retrievable storage (MRS) facility for utility-generated SNF. 3. Continued research in reprocessing options of existing and pending SNF with defined milestones. 4. Resurrection of a second

Annotated outline for the SCP conceptual design report: Office of Geologic Repositories

International Nuclear Information System (INIS)

1987-06-01

The Nuclear Waste Policy Act of 1982 (NWPA) requires that site characterization plans (SCPs) be submitted to the Nuclear Regulatory Commission (NRC), affected States and Indian tribes, and the general public for review and comment prior to the sinking of shafts at a candidate repository site. The SCP is also required by the NRC licensing procedures for the disposal of high-level waste. An Annotated Outline (AO) for Site Characterization Plans (OGR/B-5) has been prepared to provide DOE's standard format and guidance for preparation of SCPs. Consistent with the AO for SCPs. Chapter 6 of the SCP is to provide the requirements and references the media-specific design data base, describe the current design concepts, and discuss design information needs. In order to develop this design information, the Office of Geologic Repositories program is planning a SCP conceptual design phase as part of the overall repository design process. This phase is the first step in the design process, and the result and design can be expected to change as the program moves through the site characterization phase. The Annotated Outline which follows provides the standard format and guidance for the preparation of the SCP Conceptual Design Reports. It is considered to meet the intent of NRC's proposed Generic Technical Position philosophy contained therein. The SCP Conceptual Design Report will be the primary basis for preparation of Chapter 6 of the SCP and will be stand-alone reference document for the SCP. Appendix 1 to this Annotated Outline provides a correlation between Chapter 6 of the SCP and SCP Conceptual Design Report for the information purposes

Nuclear waste repository siting

International Nuclear Information System (INIS)

Soloman, B.D.; Cameron, D.M.

1987-01-01

This paper discusses the geopolitics of nuclear waste disposal in the USA. Constitutional choice and social equity perspectives are used to argue for a more open and just repository siting program. The authors assert that every potential repository site inevitably contains geologic, environmental or other imperfections and that the political process is the correct one for determining sites selected

Repository operational criteria comparative analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1994-06-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations considering the interfaces among the components of the regulations and impacts of any potential changes to those regulations. The ROC task addresses regulatory criteria and uncertainties related to the preclosure aspects of the geologic repository. Those parts of 10 CFR Part 60 that require routine guidance or minor changes to the rule were addressed in Hageman and Chowdhury, 1992. The ROC task shows a possible need for further regulatory clarity, by major changes to the rule, related to the design bases and siting of a geologic repository operations area and radiological emergency planning in order to assure defense-in-depth. The analyses, presented in this report, resulted in the development and refinement of regulatory concepts and their supporting rationale for recommendations for potential major changes to 10 CFR Pan 0 regulations

AEGIS geologic simulation model

International Nuclear Information System (INIS)

Foley, M.G.

1982-01-01

The Geologic Simulation Model (GSM) is used by the AEGIS (Assessment of Effectiveness of Geologic Isolation Systems) program at the Pacific Northwest Laboratory to simulate the dynamic geology and hydrology of a geologic nuclear waste repository site over a million-year period following repository closure. The GSM helps to organize geologic/hydrologic data; to focus attention on active natural processes by requiring their simulation; and, through interactive simulation and calibration, to reduce subjective evaluations of the geologic system. During each computer run, the GSM produces a million-year geologic history that is possible for the region and the repository site. In addition, the GSM records in permanent history files everything that occurred during that time span. Statistical analyses of data in the history files of several hundred simulations are used to classify typical evolutionary paths, to establish the probabilities associated with deviations from the typical paths, and to determine which types of perturbations of the geologic/hydrologic system, if any, are most likely to occur. These simulations will be evaluated by geologists familiar with the repository region to determine validity of the results. Perturbed systems that are determined to be the most realistic, within whatever probability limits are established, will be used for the analyses that involve radionuclide transport and dose models. The GSM is designed to be continuously refined and updated. Simulation models are site specific, and, although the submodels may have limited general applicability, the input data equirements necessitate detailed characterization of each site before application

Geologic nuclear waste repository site selection studies in the Paradox Basin, Utah

International Nuclear Information System (INIS)

Rogers, T.H.; Conwell, F.R.

1981-01-01

During Phase I regional-level studies, a literature review was conducted to ascertain geologic characteristics pertinent to repository siting factors. On the basis of the regional screening results, four areas in southeastern Utah were selected as being suitable for more detailed study in Phase II: Elk Ridge and Gibson Dome, containing nearly horizontal bedded salt deposits; Salt Valley, containing a diapiric salt anticline; and Lisbon Valley, containing a non-diapiric salt anticline. During current Phase II area studies, the four study areas are being characterized in greater detail than in Phase I. Phase II will culminate in the identification of a potentially suitable location(s), if any, that will be recommended for study in still greater detail in a subsequent phase of work. 5 refs

Salt Repository Project site study plan for stratigraphic boreholes: Revision 1, December 18, 1987

International Nuclear Information System (INIS)

1987-01-01

This site study describes the Stratigraphic Boreholes field work to be conducted during the early stages of Site Characterization at the Deaf Smith County, Texas site. The field program has been designed to provide data useful in addressing information/data needs resulting from Federal/State/local regulations, and repository program requirements. Four Stratigraphic Holes will be drilled near the perimeter of the site to document the subsurface geologic conditions in that area and to provide data necessary for design and construction of the Exploratory Shaft Facilities. Continuous samples will be recovered from the ground surface to the total depth of each sell. Geophysical well logs will provide additional coverage of the stratigraphic section. In-situ down hole testing will include short term hydrologic tests and hydraulic fracture tests to provide information on deep groundwater characteristics and regional stress patterns, respectively. Field methods/tests are chosen that provide the best or only means of obtaining the required data. The Salt Repository Project (SRP) Networks specify the schedule which the program will operate. The Technical Services Contractor is responsible for conducting the field program of drilling and testing. Samples and data will be handled and reported in accordance with established SRP procedures. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that the appropriate documentation is maintained. 30 refs., 13 figs., 4 tabs

System description of the Repository-Only System for the FY 1990 systems integration program studies

International Nuclear Information System (INIS)

McKee, R.W.; Young, J.R.; Konzek, G.J.

1991-07-01

This document provides both functional and physical descriptions of a conceptual high-level waste management system defined as a Repository-Only System. Its purpose is to provide a basis for required system computer modeling and system studies initiated in FY 1990 under the Systems Integration Program of the US Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM). The Repository-Only System is designed to accept 3000 MTU per year of spent fuel and 400 equivalent MTU per year of high-level wastes disposal in the geologic repository. This document contains both functional descriptions of the processes in the waste management system and physical descriptions of the equipment and facilities necessary for performance of those processes. These descriptions contain the level of detail needed for the projected systems analysis studies. The Repository-Only System contains all system components, from the waste storage facilities of the waste generators to the underground facilities for final disposal of the wastes. The major facilities in the system are the waste generator waste storage facilities, a repository facility that packages the wastes and than emplaces them in the geologic repository, and the transportation equipment and facilities for transporting the wastes between these major facilities. 18 refs., 39 figs

Modelling of processes occurring in deep geological repository - development of new modules in the GoldSim environment

International Nuclear Information System (INIS)

Vopalka, D.; Lukin, D.; Vokal, A.

2006-01-01

Three new modules modelling the processes that occur in a deep geological repository have been prepared in the GoldSim computer code environment (using its Transport Module). These modules help to understand the role of selected parameters in the near-field region of the final repository and to prepare an own complex model of the repository behaviour. The source term module includes radioactive decay and ingrowth in the canister, first order degradation of fuel matrix, solubility limitation of the concentration of the studied nuclides, and diffusive migration through the surrounding bentonite layer controlled by the output boundary condition formulated with respect to the rate of water flow in the rock. The corrosion module describes corrosion of canisters made of carbon steel and transport of corrosion products in the near-field region. This module computes balance equations between dissolving species and species transported by diffusion and/or advection from the surface of a solid material. The diffusion module that includes also non-linear form of the interaction isotherm can be used for an evaluation of small-scale diffusion experiments. (author)

Modelling of processes occurring in deep geological repository - Development of new modules in the GoldSim environment

Science.gov (United States)

Vopálka, D.; Lukin, D.; Vokál, A.

2006-01-01

Three new modules modelling the processes that occur in a deep geological repository have been prepared in the GoldSim computer code environment (using its Transport Module). These modules help to understand the role of selected parameters in the near-field region of the final repository and to prepare an own complex model of the repository behaviour. The source term module includes radioactive decay and ingrowth in the canister, first order degradation of fuel matrix, solubility limitation of the concentration of the studied nuclides, and diffusive migration through the surrounding bentonite layer controlled by the output boundary condition formulated with respect to the rate of water flow in the rock. The corrosion module describes corrosion of canisters made of carbon steel and transport of corrosion products in the near-field region. This module computes balance equations between dissolving species and species transported by diffusion and/or advection from the surface of a solid material. The diffusion module that includes also non-linear form of the interaction isotherm can be used for an evaluation of small-scale diffusion experiments.

Geological events in submerged areas: attributes and standards in the EMODnet Geology Project

Science.gov (United States)

Fiorentino, A.; Battaglini, L.; D'Angelo, S.

2017-12-01

EMODnet Geology is a European Project which promotes the collection and harmonization of marine geological data mapped by various national and regional mapping projects and recovered in the literature, in order to make them freely available through a web portal. Among the several features considered within the Project, "Geological events and probabilities" include submarine landslides, earthquakes, volcanic centers, tsunamis, fluid emissions and Quaternary faults in European Seas. Due to the different geological settings of European sea areas it was necessary to elaborate a comprehensive and detailed pattern of Attributes for the different features in order to represent the diverse characteristics of each occurrence. Datasets consist of shapefiles representing each event at 1:250,000 scale. The elaboration of guidelines to compile the shapefiles and attribute tables was aimed at identifying parameters that should be used to characterize events and any additional relevant information. Particular attention has been devoted to the definition of the Attribute table in order to achieve the best degree of harmonization and standardization according to the European INSPIRE Directive. One of the main objectives is the interoperability of data, in order to offer more complete, error-free and reliable information and to facilitate exchange and re-use of data even between non-homogeneous systems. Metadata and available information collected during the Project is displayed on the Portal (http://www.emodnet-geology.eu/) as polygons, lines and points layers according to their geometry. By combining all these data it might be possible to elaborate additional thematic maps which could support further research as well as land planning and management. A possible application is being experimented by the Geological Survey of Italy - ISPRA which, in cooperation with other Italian institutions contributing to EMODnet Geology, is working at the production of an update for submerged areas

Operational safety of geological disposal: IRSN project 'EXREV' for developing a safety assessment strategy for the operation and reversibility of a geological repository

International Nuclear Information System (INIS)

Tichauer, M.; Pellegrini, D.; Serres, C.; Besnus, F.

2014-01-01

A high-level waste geological disposal facility is envisioned by the legislator in the French Planning Act no. 2006-739 of 28 June 2006. This act sets major milestones for the operator (Andra) in 2013 (public debate), 2015 (licensing) and 2025 (operation). In the framework of the regulatory review process, IRSN's mission is to conduct an assessment of the safety case provided by Andra at every stage of the process for the French regulator, namely the Nuclear Safety Authority (ASN). In 2005, IRSN gathered more than twenty years of research and expertise in order to provide a comprehensive appraisal of the 'Dossier 2005' prepared by Andra, related to the feasibility of a geological disposal in the Callovo-Oxfordian clay formation. At this time, the description of the operational phase was only at a preliminary stage, but this step paved the way for developing an assessment strategy of the operational phase. In this perspective, IRSN set up the EXREV project in 2008 in order to build up a doctrine and to identify key safety issues to be dealt with. (authors)

Report on draft Area Recommendation Report for the Crystalline Repository Project

International Nuclear Information System (INIS)

1987-01-01

The draft Area Recommendation Report for the Crystalline Repository Project (ARR) is one product which is part and parcel of a process which was established by Congress and implemented by the Department of Energy. Congress, by enacting the Nuclear Waste Policy Act of 1982 (NWPA), Published Law 97-425, 96 stat 2201, 42 USC 10101, directed the Department of Energy to establish a national program which would provide for the development of repositories for the disposal of high-level radioactive waste and spent nuclear fuel, The NWPA requires, among other things, that affected Tribes and States be provided the opportunity to participate fully in the development of proposed repositories. The Fond du Lac Tribe is an affected tribe whose proprietary interests will be impacted by the Crystalline Repository Project as identified in the draft ARR. The draft ARR does not meet the obligations of the NWPA, the Treaties of 1837 and 1842 or the Trust Responsibility to Indian Tribes. The NWPA required participation by affected tribes, of which the Fond du Lac Band of Lake Superior Chippewa is included. This exclusion has placed in question the validity of the initial CRP process and does not adequately protect the interest of the Fond du Lac Band. Further study is required to fully appreciate the total affect that the Fond du Lac Bands interest may have on this report

GIS for the needs of the Radioactive Waste Repository Authority

Directory of Open Access Journals (Sweden)

Jitka Mikšová

2007-06-01

Full Text Available The Radioactive Waste Repository Authority (RAWRA is a state organisation responsible for the management of activities related to the disposal of all existing and future radioactive waste and spent nuclear fuel classed as a waste in Czech Republic. Worldwide, a deep geological repository is considered the highest degree of safety for a nuclear waste disposal. Such a repository has to be built in a stable geological environment ensuring the isolation of the stored radioactive waste from the surrounding environment for a long period of time. The selection of suitable site for the deep geological repository construction is a complicated and long term process. Considering this fact and also in respect to an assumed volume of varied datasets the GIS RAWRA was established to ensure convenient management and availability of data containing spatial information.The system is based on ESRI (ArcInfo including extensions, ArcSDE, ArcIMS, Leica Geosystems (Image Analysis and Microsoft software (MS SQL Server. Resulting datasets from six recommended potentially suitable sites for the location of a geological repository have been incorporated into the geodatabase to date. The necessary analysis was made using ESRI software tools and, in addition, custom applications were developed including the metadata editor, etc. This analysis was carried out with respect to existing geological and non-geological criteria defined for a nuclear waste repository. Finally, all six investigated sites with a total area of 240 km2 were reduced in area, each of them resulting in an area of approximately 10km2 for further detailed characterisation.

Sample management implementation plan: Salt Repository Project

International Nuclear Information System (INIS)

1987-01-01

The purpose of the Sample Management Implementation Plan is to define management controls and building requirements for handling materials collected during the site characterization of the Deaf Smith County, Texas, site. This work will be conducted for the US Department of Energy Salt Repository Project Office (SRPO). The plan provides for controls mandated by the US Nuclear Regulatory Commission and the US Environmental Protection Agency. Salt Repository Project (SRP) Sample Management will interface with program participants who request, collect, and test samples. SRP Sample Management will be responsible for the following: (1) preparing samples; (2) ensuring documentation control; (3) providing for uniform forms, labels, data formats, and transportation and storage requirements; and (4) identifying sample specifications to ensure sample quality. The SRP Sample Management Facility will be operated under a set of procedures that will impact numerous program participants. Requesters of samples will be responsible for definition of requirements in advance of collection. Sample requests for field activities will be approved by the SRPO, aided by an advisory group, the SRP Sample Allocation Committee. This document details the staffing, building, storage, and transportation requirements for establishing an SRP Sample Management Facility. Materials to be managed in the facility include rock core and rock discontinuities, soils, fluids, biota, air particulates, cultural artifacts, and crop and food stuffs. 39 refs., 3 figs., 11 tabs

Mechanical stability of repository tunnels and factors to be considered for determining tunnel spacing

International Nuclear Information System (INIS)

Takeuchi, Kunifumi

1994-01-01

Kristallin-1 organized by Nagra is currently advanced as a synthetic project regarding a high level radioactive waste (HLW) repository in Switzerland. Its host rock is granitic rocks, and the potential siting area is located in northern Switzerland. The objective of this project is to demonstrate the long term safety of a HLW repository under more site-specific conditions than before. As the detailed geological data were investigated, the average size of undisturbed crystalline rock blocks is limited horizontally to about several hundred meter, therefore, the HLW repository area must be divided into several panels to avoid fracture zones. It is necessary to make tunnel spacing as small as possible for the purpose of reasonably designing the entire layout of repository tunnels. The main factors to be considered for determining repository tunnel spacing are listed. Rock mass modeling, rock mass material properties, the analysis model and parameters, the numerical analysis of repository tunnel stability and its main conclusion are reported. The numerical analysis of the temperature distribution in near field was carried out. Tunnel spacing should be set more than 20 m in view of the maximum temperature. (K.I.)

SRP [Salt Repository Project] configuration management plan

International Nuclear Information System (INIS)

1987-01-01

This configuration management plan describes the organization, policies, and procedures that will be used on the Salt Repository Project (SRP) to implement the configuration management disciplines and controls. Configuration management is a part of baseline management. Baseline management is defined in the SRP Baseline Procedures Notebook and also includes cost and schedule baselines. Configuration management is a discipline applying technical and administrative direction and surveillance to identify and document the functional and physical characteristics of an item, to control changes to those characteristics, to record and report change processing and implementation status, and to audit the results. Configuration management is designed as a project management tool to determine and control baselines, and ensure and document all components of a project interface both physically and functionally. The purpose is to ensure that the product acquired satisfies the project's technical and operational requirements, and that the technical requirements are clearly defined and controlled throughout the development and acquisition process. 5 figs

Bure's underground research laboratory: general framework, objectives, siting process and schedule of the URL project

International Nuclear Information System (INIS)

Gaussen, J.L.

2001-01-01

Bure URL project is one of the components of the French research program dedicated to the study of HLLLW (High Level Long Lived Radioactive Waste) disposal in geologic repository within the framework of the 1991 Radioactive Waste Act. Pursuant to the said act, the objective of the URL project is to participate in the ''evaluation of options for retrievable or non- retrievable disposal in deep geologic formations''. More precisely, the goal of this URL, which is situated 300 km East of Paris, is to gain a better knowledge of a site capable of hosting a geologic repository. (author)

Vitrified radwaste from reprocessing. Material concerning the examination by the Swedish Nuclear Power Inspectorate of the supplementary geology report from the KBS-project

International Nuclear Information System (INIS)

1979-01-01

The Swedish Nuclear Power Inspectorate was designated by the Swedish Government to examine the supplementary geologic investigations performed by the utilities' KBS-project and to judge wheather the area investigated, Sternoe in southern Sweden, could be used for constructing a safe repository for radioactive wastes or not. This report contains material that was ordered by or sent to the Nuclear Power Inspectorate as well as the report by the Inspectorate to the Government. (L.E.)

Migration of fluids as a tool to evaluate the feasibility of the implantation of geological radioactive wastes repositories (RARN) in granitoid rocks: tests on granites submitted to natural deformation vs. not deformed

International Nuclear Information System (INIS)

Lopes, Nilo Henrique Balzani; Barbosa, Pedro Henrique Silva; Santos, Alanna Leite dos; Amorim, Lucas Eustáquio Dias; Freitas, Mônica Elizetti de; Rios, Francisco Javier

2017-01-01

Fluid composition and migration studies in granitoid rocks subjected to deformation events are a factor that should be considered in the selection of geologically favorable areas for RANR construction, and may be an excellent complement to engineering barrier designs. The research objective was to develop an academic approach, comparing the behavior of deformed and non-deformed granites, not being related to any CNEN project of deploying repositories. It is concluded that in the choice of suitable sites for the construction of repositories, granite bodies that are submitted to metamorphic / deformation / hydrothermal events or that are very fractured should be disregarded. The domes of granite batholith that have undergone hydraulic billing should also be discarded. It has been found that, because of the warming caused by radioactive decay reactions, there is a real possibility that the release of potentially abrasive fluids contained in the minerals can reach and corrode the walls of the repositories and / or packaging

Experimental methodology to study radionuclide sorption and migration in geological formations and engineered barriers of waste repositories

International Nuclear Information System (INIS)

Rojo Sanz, H.

2010-01-01

In Spain, the waste management options include either the possibility of a final storage in a deep geological repository (DGR) or the centralized temporal surface disposal (CTS). DGRs are based in a multi-barrier concept with the geological barrier and including the vitrified waste, the metal containers and engineered barriers such as compacted bentonite and cement-based materials. On the other hand, CTS mainly considers concrete and cement to confine the metal canisters containing the waste. Radionuclide migration will mainly take place by the existence of chemical concentration gradients being thus diffusion the main transport mechanism or by the existence of hydraulic gradients due to the existence of water-conductive fractures. Radionuclide sorption/retention on the materials composing the natural and engineered barriers is the fundamental process controlling contaminant migration. The evaluation of sorption parameters and the understanding of the different mechanisms leading to radionuclide retention are very important issues. The study of diffusion processes is very relevant as well. This paper describes the main experimental methodologies applied to analyse radionuclide transport in the different barriers of radioactive repositories. Particularly we focused on obtaining of retention parameters as distribution coefficients, kd, or retardation factors, Rf, and diffusion coefficients of radionuclides. (Author) 6 refs.

Overview of the current CRWMS repository design

International Nuclear Information System (INIS)

Daniel, R.B.; Teraoka, G.M.

1998-01-01

This paper summarizes the current design for a potential geologic repository for spent fuels and high-level wastes at Yucca Mountain, Nevada. The objective of the paper is to present the key design features of the Mined Geologic Disposal System (MGDS) surface facilities and MGDS subsurface facilities. The paper describes the following: surface layout; waste handling operations design; subsurface design; and the underground transport and emplacement design. A more detailed presentation of key features is provided in the ''Reference design description for a geologic repository'' which is located on the YMP Homepage at www.ymp.gov

Evaluation of the heat transfer in a geological repository concept containing PWR, VHTR and hybrid ads-fission spent fuels

Energy Technology Data Exchange (ETDEWEB)

Jonusan, Raoni A.S.; Pereira, Fernando; Velasquez, Carlos E.; Salome, Jean A.D.; Cardoso, Fabiano; Pereira, Claubia; Fortini, Angela, E-mail: claubia@nuclear.ufmg.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear

2017-11-01

The investigation of the thermal behavior of spent fuel (SF) materials is essential to determining appropriate potential sites to accommodate geological repositories as well as the design of canisters, considering their potential risk to people health and of environmental contamination. This work presents studies of the temperature in a canister containing spent fuels discharged from Pressurized Water Reactor (PWR), Very High-Temperature Reactor (VHTR) and Accelerator-Driven Subcritical Reactor System (ADS) reactor systems in a geological repository concept. The thermal analyses were performed with the software ANSYS, which is widely used to solve engineering problems through the Finite Element Method. The ANSYS Transient Thermal module was used. The spent nuclear fuels were set as heat sources using data of previous studies derived from decay heat curves. The studies were based on comparison of the mean temperature on a canister surface along the time under geological disposal conditions, for a same amount of each type of spent nuclear fuel evaluated. The results conclude that fuels from VHTR and ADS systems are inappropriate to be disposed in a standardized PWR canister, demanding new studies to determine the optimal amount of spent fuel and new internal canister geometries. It is also possible to conclude that the hypothetical situation of a single type of canister being used to accommodate different types of spent nuclear fuels is not technically feasible. (author)

Salt Repository Project Waste Package Program Plan: Draft

International Nuclear Information System (INIS)

Carr, J.A.; Cunnane, J.C.

1986-01-01

Under the direction of the Office of Civilian Radioactive Waste Management (OCRWM) created within the DOE by direction of the Nuclear Waste Policy Act of 1982 (NWPA), the mission of the Salt Repository Project (SRP) is to provide for the development of a candidate salt repository for disposal of high-level radioactive waste (HLW) and spent reactor fuel in a manner that fully protects the health and safety of the public and the quality of the environment. In consideration of the program needs and requirements discussed above, the SRP has decided to develop and issue this SRP Waste Package Program Plan. This document is intended to outline how the SRP plans to develop the waste package design and to show, with reasonable assurance, that the developed design will satisfy applicable requirements/performance objectives. 44 refs., 16 figs., 16 tabs

Sources/treatment of uncertainties in the performance assessment of geologic radioactive waste repositories

International Nuclear Information System (INIS)

Cranwell, R.M.

1987-01-01

Uncertainties in the performance assessment of geologic radioactive waste repositories have several sources. The more important ones include: 1) uncertainty in the conditions of a disposal system over the temporal scales set forth in regulations, 2) uncertainty in the conceptualization of the geohydrologic system, 3) uncertainty in the theoretical description of a given conceptual model of the system, 4) uncertainty in the development of computer codes to implement the solution of a mathematical model, and 5) uncertainty in the parameters and data required in the models and codes used to assess the long-term performance of the disposal system. This paper discusses each of these uncertainties and outlines methods for addressing these uncertainties

Corrosion of high purity copper as engineering barrier in deep geological repositories

International Nuclear Information System (INIS)

Ochoa, Maité; Rodríguez Martín, A.; Farina Silvia, B.

2013-01-01

Pure copper with oxygen content below 5 ppm (to minimize segregation at grain boundaries) and doped with phosphorus (to increase creep resistance) is the chosen material for the corrosion-resistant barrier of the High Level Radioactive 2 Wastecontainers in the Swedish and Finnish repository models. These models include the construction of the repository below the water table, which is a reducing environment in which copper has excellent resistance to general and localized corrosion in aqueous electrolytes. The aim of this work is contribute to determine the durability of the material, given that deep geological repositories of HLW are designed to ensure the protection of the environment for periods of hundreds of thousands years. As a first step in a more general analysis the effects of chloride, one of the main aggressive species of corrosion, are evaluated. To this purpose corrosion potential was determined and anodic polarization curves were performed in deaerated solutions varying the chloride concentration between 0.01 and 1M and the temperature between 30 and 90°C. Several electrochemical techniques were used: the evolution of corrosion potential was measured, anodic polarization curves were obtained and electrochemical impedance tests were performed. The analysis was complemented with microscopic observations of the type of corrosive attack, as well as determinations of the eventual corrosion products formed using Energy-Dispersive X-ray Analysis (EDS). Results show that the corrosion potential decreases with the increase of temperature and with the increase of chloride concentration. A correlation of the corrosion potential as a function of temperature and chloride concentration was obtained, with the purpose of making predictions in variable conditions.The current density increases both with temperature and with chloride concentration. A pitting potential is observed in certain conditions. (author)

NUMO-RMS: a practical requirements management system for the long-term management of the deep geological disposal project - 16304

International Nuclear Information System (INIS)

Ueda, Hiroyoshi; Suzuki, Satoru; Ishiguro, Katsuhiko; Oyamada, Kiyoshi; Yashio, Shoko; White, Matt; Wilmot, Roger

2009-01-01

NUMO (Nuclear Waste Management Organization of Japan) has the responsibility for implementing deep geological disposal of high-level (HLW) and transuranic (TRU) radioactive waste from the Japanese nuclear programme. A formal Requirements Management System (RMS) is planned to efficiently and effectively support the computerised implementation of the management strategy and the methodology required to drive the step-wise siting processes, and the following repository operational phase,. The RMS will help in the comprehensive management of the decision-making processes in the geological disposal project, in change management as the disposal system is optimised, in driving projects such as the R and D programme efficiently, and in maintaining structured records regarding past decisions, all of which lead to soundness of the project in terms of long-term continuity. The system is planned to have information handling and management functions using a database that includes the decisions/requirements in the programme under consideration, the way in which these are structured in terms of the decision-making process and other associated information. A two-year development programme is underway to develop and enhance an existing trial RMS to a practical system. Functions for change management, history management and association with the external timeline management system are being implemented in the system development work. The database format is being improved to accommodate the requirements management data relating to the facility design and to safety assessment of the deep geological repository. This paper will present an outline of the development work with examples to demonstrate the system's practicality. In parallel with the system/database developments, a case research of the use of requirements management in radioactive waste disposal projects was undertaken to identify key issues in the development of an RMS for radioactive waste disposal and specify a number of

Results from an International Simulation Study on Couples Thermal, Hydrological, and Mechanical (THM) Processes Near Geological Nuclear Waste Repositories

International Nuclear Information System (INIS)

J. Rutqvist; J.T. Birkholzer; M. Chijimatsu; O. Kolditz; Q.S. Liu; Y. Oda; W. Wang; C.Y. Zhang

2006-01-01

As part of the ongoing international code comparison project DECOVALEX, four research teams used five different models to simulate coupled thermal, hydrological, and mechanical (THM) processes near underground waste emplacement drifts. The simulations were conducted for two generic repository types with open or back-filled repository drifts under higher and lower post-closure temperature, respectively. In the completed first model inception phase of the project, a good agreement was achieved between the research teams in calculating THM responses for both repository types, although some disagreement in hydrological responses are currently being resolved. Good agreement in the basic thermal-mechanical responses was achieved for both repository types, even with some teams using relatively simplified thermal-elastic heat-conduction models that neglect complex near-field thermal-hydrological processes. The good agreement between the complex and simplified (and well-known) process models indicates that the basic thermal-mechanical responses can be predicted with a relatively high confidence level. The research teams have now moved on to the second phase of the project, the analysis of THM-induced permanent (irreversible) changes and the impact of those changes on the fluid flow field near an emplacement drift

Repository-relevant testing applied to the Yucca Mountain Project

International Nuclear Information System (INIS)

Bates, J.K.; Gerding, T.J.; Veleckis, E.

1989-04-01

A repository environment poses a challenge to developing a testing program because of the diverse nature of conditions that may exist at a given time during the life of the repository. A starting point is to identify whether any potential waste-water contact modes are particularly deleterious to the waste form performance, and whether any interactions between materials present in the waste package environment need to be accounted for during modeling the waste form reaction. The Unsaturated Test method in one approach that has been developed by the Yucca Mountain Project (YMP) to investigate the above issues, and a description of results that have been obtained during the testing of glass and unirradiated UO 2 are the subject of this report. 10 refs., 7 figs., 4 tabs

Status of LLNL granite projects

International Nuclear Information System (INIS)

Ramspott, L.D.

1980-01-01

The status of LLNL Projects dealing with nuclear waste disposal in granitic rocks is reviewed. This review covers work done subsequent to the June 1979 Workshop on Thermomechanical Modeling for a Hardrock Waste Repository and is prepared for the July 1980 Workshop on Thermomechanical-Hydrochemical Modeling for a Hardrock Waste Repository. Topics reviewed include laboratory determination of thermal, mechanical, and transport properties of rocks at conditions simulating a deep geologic repository, and field testing at the Climax granitic stock at the USDOE Nevada Test Site

German repository engineering in international markets. DBE TECHNOLOGY GmbH success story

Energy Technology Data Exchange (ETDEWEB)

Berlepsch, Thilo v.; Krone, Juergen [DBE Technology GmbH, Peine (Germany); Biurrun, Enrique

2015-10-15

DBE TECHNOLOGY GmbH was founded in 2000 as a spin-off from the Technology and Development Division of DBE, the German Company for the Construction and Operation of Repositories for Wastes. Today, 15 years later, DBE TECHNOLOGY GmbH can draw upon a tremendous amount of experience and knowledge, which goes far beyond the planning and operation of Deep Geologic Repositories and the development of technologies for the disposal of radioactive waste. The capabilities of DBE TECHNOLOGY GmbH are presented by leading through its history, describing its roots and highlighting main projects the company has been involved in.

Technical position on items and activities in the high-level waste geologic repository program subject to quality assurance requirements

International Nuclear Information System (INIS)

Duncan, A.B.; Bilhorn, S.G.; Kennedy, J.E.

1988-04-01

This document provides guidance on how to identify items and activities subject to Quality Assurance in the high-level nuclear waste repository program for pre-closure and post-closure phases of the repository. In the pre-closure phase, structures, systems and components essential to the prevention or mitigation of an accident that could result in an off-site radiation dose of 0.5rem or greater are termed ''important to safety''. In the post-closure phase, the barriers which are relied on to meet the containment and isolation requirements are defined as ''important to waste isolation''. These structures, systems, components, and barriers, and the activities related to their characterization, design, construction, and operation are required to meet quality assurance (QA) criteria to provide confidence in the performance of the geologic repository. The list of structures, systems, and components important to safety and engineered barriers important to waste isolation is referred to as the ''Q-List'' and lies within the scope of the QA program. 10 refs

Decommissioning of surface facilities associated with repositories for the deep geological disposal of high-level nuclear wastes

International Nuclear Information System (INIS)

Heckman, R.A.

1978-11-01

A methodology is presented in this paper to evaluate the decommissioning of the surface facilities associated with repositories for the deep geological disposal of high-level nuclear wastes. A cost/risk index (figure of merit), expressed as $/manrem, is proposed as an evaluation criteria. On the basis of this cost/risk index, we gain insight into the advisability of adapting certain decontamination design options into the original facility. Three modes are considered: protective storage, entombment, and dismantlement. Cost estimates are made for the direct labor involved in each of the alternative modes for a baseline design case. Similarly, occupational radiation exposures are estimated, with a larger degree of uncertainty, for each of the modes. Combination of these estimates produces the cost/risk index. To illustrate the methodology, an example using a preliminary baseline repository design is discussed

Engineered barrier system and waste package design concepts for a potential geologic repository at Yucca Mountain

International Nuclear Information System (INIS)

Short, D.W.; Ruffner, D.J.; Jardine, L.J.

1991-10-01

We are using an iterative process to develop preliminary concept descriptions for the Engineered Barrier System and waste-package components for the potential geologic repository at Yucca Mountain. The process allows multiple design concepts to be developed subject to major constraints, requirements, and assumptions. Involved in the highly interactive and interdependent steps of the process are technical specialists in engineering, metallic and nonmetallic materials, chemistry, geomechanics, hydrology, and geochemistry. We have developed preliminary design concepts that satisfy both technical and nontechnical (e.g., programmatic or policy) requirements

Nuclear waste repository design and construction

International Nuclear Information System (INIS)

Bohlke, B.M.; Monsees, J.E.

1987-01-01

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt

Salt Repository Project transportation program plan

International Nuclear Information System (INIS)

Fisher, R.L.; Greenberg, A.H.; Anderson, T.L.; Yates, K.R.

1987-01-01

The Salt Repository Project (SRP) has the responsibility to develop a comprehensive transportation program plan (TrPP) that treats the transportation of workers, supplies, and high-level radioactive waste to the site and the transportation of salt, low-level, and transuranic wastes from the site. The TrPP has developed a systematic approach to transportation which is directed towards satisfying statutes, regulations, and directives and is guided by a hierarchy of specific functional requirements, strategies, plans, and reports. The TrPP identifies and develops the planning process for transportation-related studies and provides guidance to staff in performing and documenting these activities. The TrPP also includes an explanation of the responsibilities of the organizational elements involved in these transportation studies. Several of the report chapters relate to identifying routes for transporting nuclear waste to the site. These include a chapter on identifying an access corridor for a new rail route leading to the site, identifying and evaluating emergency-response preparedness capabilities along candidate routes in the state, and identifying alternative routes from the state border, ports, or in-state reactors to the site. The TrPP also includes plans for identifying salt disposal routes and a discussion of repository/transportation interface requirements. 89 refs., 6 figs

Parametric study of geohydrologic performance characteristics for geologic waste repositories

International Nuclear Information System (INIS)

Bailey, C.E.; Marine, I.W.

1980-11-01

One of the major objectives of the National Waste Terminal Storage Program is to identify potential geologic sites for storage and isolation of radioactive waste (and possibly irradiated fuel). Potential sites for the storage and isolation of radioactive waste or spent fuel in a geologic rock unit are being carefully evaluated to ensure that radionuclides from the stored waste or fuel will never appear in the biosphere in amounts that would constitute a hazard to the health and safety of the public. The objective of this report is to quantify and present in graphical form the effects of significant geohydrologic and other performance characteristics that would influence the movement of radionuclides from a storage site in a rock unit to the biosphere. The effort in this study was focused on transport by groundwater because that is the most likely method of radionuclide escape. Graphs of the major performance characteristics that influence the transport of radionuclides from a repository to the biosphere by groundwater are presented. The major characteristics addressed are radioactive decay, leach rate, hydraulic conductivity, porosity, groundwater gradient, hydrodynamic dispersion, ion exchange, and distance to the biosphere. These major performance characteristics are combind with each other and with the results of certain other combinations and presented in graphical form to provide the interrelationships of values measured during field studies. The graphical form of presentation should be useful in the screening process of site selection. An appendix illustrates the use of these graphs to assess the suitability of a site

Considerations on pressure build-up in deep geological repositories for radioactive waste; Betrachtungen zum Druckaufbau in einem geologischen Tiefenlager fuer radioaktive Abfaelle

Energy Technology Data Exchange (ETDEWEB)

Beer, Hans-Frieder [Paul Scherrer Institut, Villigen-PSI (Switzerland)

2015-07-01

Gas formation caused by corrosion of metals is a pivotal point with respect to the safety analysis of deep geological repositories. Solid corrosion products are formed unavoidably during the gas formation. The volumes of these solid corrosion products are multiples of the original waste volume. These solid corrosion products are chemically extremely stable and result in a pressure increase inside the repository. This pressure is considerably higher than that of the overlaying rock. The question that arises is, why this aspect is not considered in the consulted documents.

Nye County, Nevada 1992 nuclear waste repository program: Program overview. Final report

International Nuclear Information System (INIS)

1998-01-01

The purpose of this document is to provide an overview of the Nye County FY92 Nuclear Waste Repository Program (Program). Funds to pay for Program costs will come from the Federal Nuclear Waste Fund, which was established under the Nuclear Waste Policy Act of 1982 (NWPA). In early 1983, the Yucca Mountain was identified as a potentially suitable site for the nation's first geologic repository for spent reactor fuel and high-level radioactive waste. Later that year, the Nye County Board of County Commissioners (Board) established the capability to monitor the Federal effort to implement the NWPA and evaluate the potential impacts of repository-related activities on Nye County. Over the last eight years, the County's program has grown in complexity and cost in order to address DOE's evolving site characterization studies, and prepare for the potential for facility construction and operation. Changes were necessary as well, in response to Congress's redirection of the repository program specified in the amendments, to the NWPA approved in 1987. In early FY 1991, the County formally established a project office to plan and implement its program of work. The Repository Project Office's (RPO) mission and functions are provided in Section 2.0. The RPO organization structure is described in Section 3.0

Modeling of container failure and radionuclide release from a geologic nuclear waste repository

International Nuclear Information System (INIS)

Kim, Chang Lak; Kim, Jhin Wung; Choi, Kwang Sub; Cho, Chan Hee

1989-02-01

Generally, two processes are involved in leaching and dissolution; (1) chemical reactions and (2) mass transfer by diffusion. The chemical reaction controls the dissolution rates only during the early stage of exposure to groundwater. The exterior-field mass transfer may control the long-term dissolution rates from the waste solid in a geologic repository. Masstransfer analyses rely on detailed and careful application of the governing equations that describe the mechanistic processes of transport of material between and within phases. We develop analytical models to predict the radionuclide release rate into the groundwater with five different approaches: a measurement-based model, a diffusion model, a kinetics model, a diffusion-and-kinetics model, and a modified diffusion model. We also collected experimental leaching data for a partial validation of the radionuclide release model based on the mass transfer theory. Among various types of corrosions, pitting is the most significant because of its rapid growth. The failure time of the waste container, which also can be interpreted as the containment time, is a milestone of the performance of a repository. We develop analytical models to predict the pit growth rate on the container surface with three different approaches: an experimental method, a statistical method, and a mathematical method based on the diffusion theory. (Author)

Monte Carlo simulations for generic granite repository studies

Energy Technology Data Exchange (ETDEWEB)

Chu, Shaoping [Los Alamos National Laboratory; Lee, Joon H [SNL; Wang, Yifeng [SNL

2010-12-08

In a collaborative study between Los Alamos National Laboratory (LANL) and Sandia National Laboratories (SNL) for the DOE-NE Office of Fuel Cycle Technologies Used Fuel Disposition (UFD) Campaign project, we have conducted preliminary system-level analyses to support the development of a long-term strategy for geologic disposal of high-level radioactive waste. A general modeling framework consisting of a near- and a far-field submodel for a granite GDSE was developed. A representative far-field transport model for a generic granite repository was merged with an integrated systems (GoldSim) near-field model. Integrated Monte Carlo model runs with the combined near- and farfield transport models were performed, and the parameter sensitivities were evaluated for the combined system. In addition, a sub-set of radionuclides that are potentially important to repository performance were identified and evaluated for a series of model runs. The analyses were conducted with different waste inventory scenarios. Analyses were also conducted for different repository radionuelide release scenarios. While the results to date are for a generic granite repository, the work establishes the method to be used in the future to provide guidance on the development of strategy for long-term disposal of high-level radioactive waste in a granite repository.

The SeaView EarthCube project: Lessons Learned from Integrating Across Repositories

Science.gov (United States)

Diggs, S. C.; Stocks, K. I.; Arko, R. A.; Kinkade, D.; Shepherd, A.; Olson, C. J.; Pham, A.

2017-12-01

SeaView is an NSF-funded EarthCube Integrative Activity Project working with 5 existing data repositories* to provide oceanographers with highly integrated thematic data collections in user-requested formats. The project has three complementary goals: Supporting Scientists: SeaView targets scientists' need for easy access to data of interest that are ready to import into their preferred tool. Strengthening Repositories: By integrating data from multiple repositories for science use, SeaView is helping the ocean data repositories align their data and processes and make ocean data more accessible and easily integrated. Informing EarthCube (earthcube.org): SeaView's experience as an integration demonstration can inform the larger NSF EarthCube architecture and design effort. The challenges faced in this small-scale effort are informative to geosciences cyberinfrastructure more generally. Here we focus on the lessons learned that may inform other data facilities and integrative architecture projects. (The SeaView data collections will be presented at the Ocean Sciences 2018 meeting.) One example is the importance of shared semantics, with persistent identifiers, for key integration elements across the data sets (e.g. cruise, parameter, and project/program.) These must allow for revision through time and should have an agreed authority or process for resolving conflicts: aligning identifiers and correcting errors were time consuming and often required both deep domain knowledge and "back end" knowledge of the data facilities. Another example is the need for robust provenance, and tools that support automated or semi-automated data transform pipelines that capture provenance. Multiple copies and versions of data are now flowing into repositories, and onward to long-term archives such as NOAA NCEI and umbrella portals such as DataONE. Exact copies can be identified with hashes (for those that have the skills), but it can be painfully difficult to understand the processing

Local Communities' Expectations and Demands on Monitoring and the Preservation of Records, Knowledge and Memory of a Deep Geological Repository

International Nuclear Information System (INIS)

2014-01-01

This report explores the role, needs and expectations of local communities regarding monitoring and RK and M preservation of radioactive waste management facilities, in particular deep geological repositories. It was developed through both field and desk research. A questionnaire survey to FSC members was undertaken in July and August 2012, followed by interviews with a broad range of involved stakeholders. A brief update survey in August and September 2013 gathered replies from a subset of countries. A literature review was carried out, focusing on FSC publications and other documents and publications found through internet or suggested by interviewees. After a brief presentation of the study rationale and methodology in section 1, section 2 reviews the FSC literature on aspects related to RK and M and monitoring. In section 3 the report identifies concerns and expectations of local communities regarding monitoring in the different phases of the repository life cycle and in the different national contexts, according to the results gathered from the survey and interviews undertaken as part of this project. The fourth section discusses how RK and M preservation may emerge as a subject of debate with local stakeholders in different countries in the years to come. Section 5 recognises that monitoring and RK and M preservation potentially serve to build and maintain confidence in the long-term safety of deep geological repositories. Finally, the concept of oversight is considered in section 6 as a term that embraces monitoring and RK and M, and its interpretation in different reports is illustrated. Final reflections, with some conclusions, are provided in section 7. Four appendixes are offered. Appendix I summarises in a table the design features of a radioactive waste management facility that may help the memory of the site to be preserved over generations, as suggested in NEA (2007). Appendix II reports statements related with monitoring and RK and M preservation in

Canada's Deep Geological Repository for Used Nuclear Fuel - Geo-scientific Site Evaluation Process - 13117

Energy Technology Data Exchange (ETDEWEB)

Blyth, Alec; Ben Belfadhel, Mahrez; Hirschorn, Sarah; Hamilton, Duncan; McKelvie, Jennifer [Nuclear Waste Management Organization, 22 St. Clair Avenue East, Toronto, Ontario M4T 2S3 (Canada)

2013-07-01

The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable rock formation at a depth of approximately 500 meters (m) (1,640 feet [ft]). In May 2010, the NWMO published a nine-step site selection process that serves as the road map to decision-making on the location for the deep geological repository. The safety and appropriateness of any potential site will be assessed against a number of factors, both technical and social in nature. The selected site will be one that can be demonstrated to be able to safely contain and isolate used nuclear fuel, protecting humans and the environment over the very long term. The geo-scientific suitability of potential candidate sites will be assessed in a stepwise manner following a progressive and thorough site evaluation process that addresses a series of geo-scientific factors revolving around five safety functions. The geo-scientific site evaluation process includes: Initial Screenings; Preliminary Assessments; and Detailed Site Evaluations. As of November 2012, 22 communities have entered the site selection process (three in northern Saskatchewan and 18 in northwestern and southwestern Ontario). (authors)

Concepts and examples of safety analyses for radioactive waste repositories in continental geological formations

International Nuclear Information System (INIS)

1983-01-01

This document is addressed to authorities and specialists responsible for or involved in planning, performing and/or reviewing safety assessments of underground radioactive waste repositories. It is a companion to a general introductory document on the subject ''Safety Assessment for the Underground Disposal of Radioactive Wastes'', IAEA Safety Series No. 56, 1981, and reference to this earlier document will facilitate the reader's understanding of the present report. Since examples of safety analyses are summarized here, it is hoped that this document will contribute to providing a basis for a common understanding among authorities and specialists concerned with the numerous studies involving a variety of scientific disciplines. While providing technical information, this document is also intended to stimulate further international discussion. The purposes of this report are: a) to identify the factors to be taken into account in radiological safety analyses of deep geological repositories, indicating as far as possible their relative importance during the various phases of system development; b) to show how these factors have been analysed in various safety assessment studies; and c) to comment on the merits of the selected and alternative approaches

Concepts and examples of safety analyses for radioactive waste repositories in continental geological formations

Energy Technology Data Exchange (ETDEWEB)

1983-01-01

This document is addressed to authorities and specialists responsible for or involved in planning, performing and/or reviewing safety assessments of underground radioactive waste repositories. It is a companion to a general introductory document on the subject ''Safety Assessment for the Underground Disposal of Radioactive Wastes'', IAEA Safety Series No. 56, 1981, and reference to this earlier document will facilitate the reader's understanding of the present report. Since examples of safety analyses are summarized here, it is hoped that this document will contribute to providing a basis for a common understanding among authorities and specialists concerned with the numerous studies involving a variety of scientific disciplines. While providing technical information, this document is also intended to stimulate further international discussion. The purposes of this report are: a) to identify the factors to be taken into account in radiological safety analyses of deep geological repositories, indicating as far as possible their relative importance during the various phases of system development; b) to show how these factors have been analysed in various safety assessment studies; and c) to comment on the merits of the selected and alternative approaches.

First Workshop on Design and Construction of Deep Repositories - Theme: Excavation through water-conducting major fracture zones

International Nuclear Information System (INIS)

Baeckblom, G.; Svemar, C.

1994-01-01

Final disposal of high-level nuclear waste has not yet been carried out in any country today. The concepts under development are all based on geological repositories, i.e., disposal at a sufficient depth below the surface to provide stable mechanical, hydrological and chemical conditions during the period the waste needs to be isolated from man. In the cases where crystalline bedrock is considered the proposed repository depths vary between 300-1000 m. The construction, operation and sealing of a deep geological repository must meet various criteria that in many respects are more detailed and more demanding than usual in underground construction projects today. The work shall be done so that occupational safety is ensured. The work also shall conform to whatever restrictions are necessary for ensuring pre-closure operational safety and post-closure long-term safety. March 1993 SKB arranged a two-day international workshop to discuss design and construction of repositories. Close to 40 participants from eight countries shared experiences regarding passage of major water-conducting fracture zones and other matters. This report summarizes the contributions to the workshop

A new integrated approach to demonstrate the safe disposal of high-level radioactive waste and spent nuclear fuel in a geological repository

International Nuclear Information System (INIS)

Mueller-Hoeppe, N.; Krone, J.; Niehues, N.; Raitz von Frentz, R.

2000-01-01

Multi-barrier systems are accepted as the basic approach for long term environmental safe isolation of radioactive waste in geological repositories. Assessing the performance of natural and engineered barriers is one of the major difficulties in producing evidence of environmental safety for any radioactive waste disposal facility, due to the enormous complexity of scenarios and uncertainties to be considered. This paper outlines a new methodological approach originally developed basically for a repository in salt, but that can be transferred with minor modifications to any other host rock formation. The approach is based on the integration of following elements: (1) Implementation of a simple method and efficient criteria to assess and prove the tightness of geological and engineered barriers; (2) Using the method of Partial Safety Factors in order to assess barrier performance at certain reasonable level of confidence; (3) Integration of a diverse geochemical barrier in the near field of waste emplacement limiting systematically the radiological consequences from any radionuclide release in safety investigations and (4) Risk based approach for the assessment of radionuclide releases. Indicative calculations performed with extremely conservative assumptions allowed to exclude any radiological health consequences from a HLW repository in salt to a reference person with a safety level of 99,9999% per year. (author)

Site selection for deep geologic repositories - Consequences for society, economy and environment; was kommt auf die regionen zu? Auswirkungen geologischer tiefenlager auf gesellschaft, wirtschaft und lebensraum

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-03-15

In a few years, Switzerland will make the decision regarding site selection for geological underground repositories for the storage of radioactive wastes. Besides the safety issue, many citizens are interested in how such a repository will affect environment, economy and society in the selected site's region. This brochure summarizes the results of many studies on the socio-economic impacts of nuclear waste repositories. Radioactive wastes must be stored in such a way that mankind and environment are safely protected for a long period of time. How this goal may be achieved, is already known: geologic deep repositories warrant long-term safety. For the oncoming years in Switzerland the question is where the repository will be built. The search for an appropriate site for a repository in the proposed regions will launch discussions. Within the participative framework the regions may bring their requests. The demonstration of the safety of potential repository sites has the highest priority in the selection process. In the third procedural step additional rock investigations will be made. The socio-economic studies and the experience with existing plants show that radioactive waste management plants can be built and operated in good agreement with environmental requirements. The radioactive wastes in a deep underground repository are stored many hundred meters below the Earth's surface. There, they are isolated from our vital space. Technical barriers and the surrounding dense rock confinement prevent the release of radioactive materials into the environment. A deep repository has positive consequences for the regional economy. It increases trade and value creation and creates work places. The socio-economic impacts practically extend over one century, but strongly vary with time; they are the largest during the building period. High life quality and a positive population development in the selected site region are compatible with a deep repository. A fair

Redox front formation in an uplifting sedimentary rock sequence: An analogue for redox-controlling processes in the geosphere around deep geological repositories for radioactive waste

International Nuclear Information System (INIS)

Yoshida, H.; Metcalfe, R.; Yamamoto, K.; Murakami, Y.; Hoshii, D.; Kanekiyo, A.; Naganuma, T.; Hayashi, T.

2008-01-01

Subsurface redox fronts control the mobilization and fixation of many trace elements, including potential pollutants such as certain radionuclides. Any safety assessment for a deep geological repository for radioactive wastes needs to take into account adequately the long-term redox processes in the geosphere surrounding the repository. To build confidence in understanding these processes, a redox front in a reduced siliceous sedimentary rock distributed in an uplifting area in Japan has been studied in detail. Geochemical analyses show increased concentrations of Fe and trace elements, including rare earth elements (REEs), at the redox front, even though concentrations of reduced rock matrix constituents show little change. Detailed SEM observations revealed that fossilized microorganisms composed of amorphous granules made exclusively of Fe and Si occur in the rock's pore space. Microbial 16S rDNA analysis suggests that there is presently a zonation of different bacterial groups within the redox band, and bacterial zonation played an important role in the concentration of Fe-oxyhydroxides at the redox front. These water-rock-microbe interactions can be considered analogous to the processes occurring in the redox fronts that would develop around geological repositories for radioactive waste. Once formed, the Fe-oxyhydroxides within such a front would be preserved even after reducing conditions resume following repository closure

Redox front formation in an uplifting sedimentary rock sequence: An analogue for redox-controlling processes in the geosphere around deep geological repositories for radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Yoshida, H. [Nagoya University Museum, Material Research Section, Furocho, Nagoya 464-8602 (Japan)], E-mail: dora@num.nagoya-u.ac.jp; Metcalfe, R. [Quintessa Japan, Queen' s Tower A7-707, Minatomirai, Yokohama 220-6007 (Japan); Yamamoto, K. [Nagoya University Museum, Material Research Section, Furocho, Nagoya 464-8602 (Japan); Murakami, Y. [Japan Atomic Energy Agency (JAEA), Tono Geoscience Centre (Japan); Hoshii, D.; Kanekiyo, A.; Naganuma, T. [Hiroshima University, Higashi Hiroshima, Kagamiyama 1-4-4 (Japan); Hayashi, T. [Asahi University, Department of Dental Pharmacology, Hozumi, Gifu (Japan)

2008-08-15

Subsurface redox fronts control the mobilization and fixation of many trace elements, including potential pollutants such as certain radionuclides. Any safety assessment for a deep geological repository for radioactive wastes needs to take into account adequately the long-term redox processes in the geosphere surrounding the repository. To build confidence in understanding these processes, a redox front in a reduced siliceous sedimentary rock distributed in an uplifting area in Japan has been studied in detail. Geochemical analyses show increased concentrations of Fe and trace elements, including rare earth elements (REEs), at the redox front, even though concentrations of reduced rock matrix constituents show little change. Detailed SEM observations revealed that fossilized microorganisms composed of amorphous granules made exclusively of Fe and Si occur in the rock's pore space. Microbial 16S rDNA analysis suggests that there is presently a zonation of different bacterial groups within the redox band, and bacterial zonation played an important role in the concentration of Fe-oxyhydroxides at the redox front. These water-rock-microbe interactions can be considered analogous to the processes occurring in the redox fronts that would develop around geological repositories for radioactive waste. Once formed, the Fe-oxyhydroxides within such a front would be preserved even after reducing conditions resume following repository closure.

Co-operation between Slovenia and Croatia in the low- and intermediate level radioactive waste repository project

International Nuclear Information System (INIS)

Schaller, A.; Lokner, V.; Subasic, D.; Zeleznik, N.; Mele, I.; Tomse, P.

2001-01-01

The paper describes the LILW repository project development in Slovenia and Croatia from the viewpoint of co-operation of national agencies for radioactive waste management - ARAO in Slovenia and APO in Croatia. The project performance, as well as the co-operation itself, are based on the fact that NPP Krsko, sited in Slovenia, is the joint venture facility of both countries, which are consequently obliged to find a proper solution for final disposal of operational and decommissioning radioactive waste generated by the plant. The main aspects of the project development in both countries, such as LILW repository site selection and characterisation, development of repository conceptual design, performance assessment/safety analysis procedures and public participation, are presented in the paper. Based on separate descriptions of the project development in Slovenia and Croatia respectively, the main aspects of co-operation between ARAO and APO are elaborated.(author)

OPG's deep geologic repository for low and intermediate level waste - public participation and aboriginal engagement

International Nuclear Information System (INIS)

Wilson, M.

2011-01-01

Ontario Power Generation (OPG)'s Public Participation and Aboriginal Engagement Program for the proposed Deep Geologic Repository (DGR) for low and intermediate level waste (L and ILW) began with the signing of a Memorandum of Understanding (MOU) in 2002 between OPG and the Municipality of Kincardine. The MOU set out the terms under which the two parties would jointly study the feasibility of different options for the long-term management of L and ILW at the Bruce nuclear site. A consultant, independent from both the Municipality of Kincardine and OPG, was retained to manage the assessment of options as well as a communication plan to ensure the public and Aboriginal peoples were kept apprised of all activities associated with the MOU. This early commitment to transparency and openness, with its ensuing opportunities for the public and Aboriginal peoples to become informed, ask questions, and engage in meaningful two-way dialogue about the early assessment of options, established the foundation and later became the hallmark of the DGR Project's Public Participation and Aboriginal Engagement program. This paper provides an overview of the development, nature and results of that program as it has evolved through the early investigative stages of options and through the environmental assessment and licencing process for the proposed DGR Project. (author)

Office of Crystalline Repository Development FY 83 technical project plan

International Nuclear Information System (INIS)

1983-03-01

The technical plan for FY 83 activities of the Office of Crystalline Repository Development is presented in detail. Crystalline Rock Project objectives are discussed in relation to the National Waste Terminal storage (NWTS) program. The plan is in full compliance with requirements mandated by the Nuclear Waste Policy Act of 1982. Implementation will comply with the requirements and criteria set forth in the Nuclear Regulatory Commission regulations (10 CFR 60) and the Environmental Protection Agency standard (40 CFR 191). Technical approaches and the related milestones and schedules are presented for each of the Level 3 NWTS work Breakdown Structure Tasks. These are: Systems, Waste Package, Site, Repository, Regulatory and Institutional, Test Facilities and Excavations, Land Acquisition, and Program Management

Technical issues in the geologic disposal of radioactive wastes