Novel Sample-handling Approach for XRD Analysis with Minimal Sample Preparation

Science.gov (United States)

Sarrazin, P.; Chipera, S.; Bish, D.; Blake, D.; Feldman, S.; Vaniman, D.; Bryson, C.

2004-01-01

Sample preparation and sample handling are among the most critical operations associated with X-ray diffraction (XRD) analysis. These operations require attention in a laboratory environment, but they become a major constraint in the deployment of XRD instruments for robotic planetary exploration. We are developing a novel sample handling system that dramatically relaxes the constraints on sample preparation by allowing characterization of coarse-grained material that would normally be impossible to analyze with conventional powder-XRD techniques.

Newly introduced sample preparation techniques: towards miniaturization.

Science.gov (United States)

Costa, Rosaria

2014-01-01

Sampling and sample preparation are of crucial importance in an analytical procedure, representing quite often a source of errors. The technique chosen for the isolation of analytes greatly affects the success of a chemical determination. On the other hand, growing concerns about environmental and human safety, along with the introduction of international regulations for quality control, have moved the interest of scientists towards specific needs. Newly introduced sample preparation techniques are challenged to meet new criteria: (i) miniaturization, (ii) higher sensitivity and selectivity, and (iii) automation. In this survey, the most recent techniques introduced in the field of sample preparation will be described and discussed, along with many examples of applications.

Generic safety documentation model

International Nuclear Information System (INIS)

Mahn, J.A.

1994-04-01

This document is intended to be a resource for preparers of safety documentation for Sandia National Laboratories, New Mexico facilities. It provides standardized discussions of some topics that are generic to most, if not all, Sandia/NM facilities safety documents. The material provides a ''core'' upon which to develop facility-specific safety documentation. The use of the information in this document will reduce the cost of safety document preparation and improve consistency of information

An evaluation of consumers' knowledge, perceptions and attitudes regarding generic medicines in Auckland.

Science.gov (United States)

Babar, Zaheer-Ud-Din; Stewart, Joanna; Reddy, Shiwangni; Alzaher, Woroud; Vareed, Prateeka; Yacoub, Nineweh; Dhroptee, Bandhana; Rew, Anne

2010-08-01

The aim of this project was to evaluate the perceptions, knowledge and attitudes regarding generic medicines. A cross-sectional study, with self administered questionnaires, was conducted to survey consumers visiting pharmacies in four regions of Auckland (North Shore, Waitakere, Central Auckland and South Auckland). Through stratified random sampling, approximately 10% of pharmacies from each region were selected, which turn out to be 30 pharmacies. Every alternate customer coming to the pharmacy, who was eligible to participate in the study, was asked by the researchers to complete the questionnaire. A total of 441 questionnaires were included in the analysis. Different response rates were obtained in different regions of Auckland. Of all respondents, 51.6% had previous knowledge of generic medicines. Pharmacists were the main source of information regarding generic medicines followed by doctors and media. A higher level of education had a direct relationship with having correct knowledge of generics (P = .002). Attitude of participants toward the use of generic medicines was determined by their knowledge of generics, whether it was recommended by a pharmacist and their type of illness. Participants were more prepared to change to a generic for a minor illness (79%) than for a major illness (58.7%). Those who had better knowledge were more likely than those with poor knowledge to say they would to use a generic in major illness (P = .001) as well as minor illness (P < .0001). Previous positive experiences with generics also determined consumers' willingness to use generics. Many consumers have misconceptions regarding generic medicines. Having knowledge about generics and the advice by doctors and pharmacists are key indicators to improve the quality use of generic medicines.

Green approaches in sample preparation of bioanalytical samples prior to chromatographic analysis.

Science.gov (United States)

Filippou, Olga; Bitas, Dimitrios; Samanidou, Victoria

2017-02-01

Sample preparation is considered to be the most challenging step of the analytical procedure, since it has an effect on the whole analytical methodology, therefore it contributes significantly to the greenness or lack of it of the entire process. The elimination of the sample treatment steps, pursuing at the same time the reduction of the amount of the sample, strong reductions in consumption of hazardous reagents and energy also maximizing safety for operators and environment, the avoidance of the use of big amount of organic solvents, form the basis for greening sample preparation and analytical methods. In the last decade, the development and utilization of greener and sustainable microextraction techniques is an alternative to classical sample preparation procedures. In this review, the main green microextraction techniques (solid phase microextraction, stir bar sorptive extraction, hollow-fiber liquid phase microextraction, dispersive liquid - liquid microextraction, etc.) will be presented, with special attention to bioanalytical applications of these environment-friendly sample preparation techniques which comply with the green analytical chemistry principles. Copyright © 2016 Elsevier B.V. All rights reserved.

Sample preparation of environmental samples using benzene synthesis followed by high-performance LSC

International Nuclear Information System (INIS)

Filippis, S. De; Noakes, J.E.

1991-01-01

Liquid scintillation counting (LSC) techniques have been widely employed as the detection method for determining environmental levels of tritium and 14 C. Since anthropogenic and nonanthropogenic inputs to the environment are a concern, sampling the environment surrounding a nuclear power facility or fuel reprocessing operation requires the collection of many different sample types, including agriculture products, water, biota, aquatic life, soil, and vegetation. These sample types are not suitable for the direct detection of tritium of 14 C for liquid scintillation techniques. Each sample type must be initially prepared in order to obtain the carbon or hydrogen component of interest and present this in a chemical form that is compatible with common chemicals used in scintillation counting applications. Converting the sample of interest to chemically pure benzene as a sample preparation technique has been widely accepted for processing samples for radiocarbon age-dating applications. The synthesized benzene is composed of the carbon or hydrogen atoms from the original sample and is ideal as a solvent for LSC with excellent photo-optical properties. Benzene synthesis followed by low-background scintillation counting can be applied to the preparation and measurement of environmental samples yielding good detection sensitivities, high radionuclide counting efficiency, and shorter preparation time. The method of benzene synthesis provides a unique approach to the preparation of a wide variety of environmental sample types using similar chemistry for all samples

Quantitative sample preparation of some heavy elements

International Nuclear Information System (INIS)

Jaffey, A.H.

1977-01-01

A discussion is given of some techniques that have been useful in quantitatively preparing and analyzing samples used in the half-life determinations of some plutonium and uranium isotopes. Application of these methods to the preparation of uranium and plutonium samples used in neutron experiments is discussed

7 CFR 27.21 - Preparation of samples of cotton.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Preparation of samples of cotton. 27.21 Section 27.21... REGULATIONS COTTON CLASSIFICATION UNDER COTTON FUTURES LEGISLATION Regulations Inspection and Samples § 27.21 Preparation of samples of cotton. The samples from each bale shall be prepared as specified in this section...

Sample preparation in alkaline media

International Nuclear Information System (INIS)

Nobrega, Joaquim A.; Santos, Mirian C.; Sousa, Rafael A. de; Cadore, Solange; Barnes, Ramon M.; Tatro, Mark

2006-01-01

The use of tetramethylammonium hydroxide, tertiary amines and strongly alkaline reagents for sample treatment involving extraction and digestion procedures is discussed in this review. The preparation of slurries is also discussed. Based on literature data, alkaline media offer a good alternative for sample preparation involving an appreciable group of analytes in different types of samples. These reagents are also successfully employed in tailored speciation procedures wherein there is a critical dependence on maintenance of chemical forms. The effects of these reagents on measurements performed using spectroanalytical techniques are discussed. Several undesirable effects on transport and atomization processes necessitate use of the method of standard additions to obtain accurate results. It is also evident that alkaline media can improve the performance of techniques such as inductively coupled plasma mass spectrometry and accessories, such as autosamplers coupled to graphite furnace atomic absorption spectrometers

Urine sample preparation for proteomic analysis.

Science.gov (United States)

Olszowy, Pawel; Buszewski, Boguslaw

2014-10-01

Sample preparation for both environmental and more importantly biological matrices is a bottleneck of all kinds of analytical processes. In the case of proteomic analysis this element is even more important due to the amount of cross-reactions that should be taken into consideration. The incorporation of new post-translational modifications, protein hydrolysis, or even its degradation is possible as side effects of proteins sample processing. If protocols are evaluated appropriately, then identification of such proteins does not bring difficulties. However, if structural changes are provided without sufficient attention then protein sequence coverage will be reduced or even identification of such proteins could be impossible. This review summarizes obstacles and achievements in protein sample preparation of urine for proteome analysis using different tools for mass spectrometry analysis. The main aim is to present comprehensively the idea of urine application as a valuable matrix. This article is dedicated to sample preparation and application of urine mainly in novel cancer biomarkers discovery. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Generic Learning-Based Ensemble Framework for Small Sample Size Face Recognition in Multi-Camera Networks.

Science.gov (United States)

Zhang, Cuicui; Liang, Xuefeng; Matsuyama, Takashi

2014-12-08

Multi-camera networks have gained great interest in video-based surveillance systems for security monitoring, access control, etc. Person re-identification is an essential and challenging task in multi-camera networks, which aims to determine if a given individual has already appeared over the camera network. Individual recognition often uses faces as a trial and requires a large number of samples during the training phrase. This is difficult to fulfill due to the limitation of the camera hardware system and the unconstrained image capturing conditions. Conventional face recognition algorithms often encounter the "small sample size" (SSS) problem arising from the small number of training samples compared to the high dimensionality of the sample space. To overcome this problem, interest in the combination of multiple base classifiers has sparked research efforts in ensemble methods. However, existing ensemble methods still open two questions: (1) how to define diverse base classifiers from the small data; (2) how to avoid the diversity/accuracy dilemma occurring during ensemble. To address these problems, this paper proposes a novel generic learning-based ensemble framework, which augments the small data by generating new samples based on a generic distribution and introduces a tailored 0-1 knapsack algorithm to alleviate the diversity/accuracy dilemma. More diverse base classifiers can be generated from the expanded face space, and more appropriate base classifiers are selected for ensemble. Extensive experimental results on four benchmarks demonstrate the higher ability of our system to cope with the SSS problem compared to the state-of-the-art system.

Generic Learning-Based Ensemble Framework for Small Sample Size Face Recognition in Multi-Camera Networks

Directory of Open Access Journals (Sweden)

Cuicui Zhang

2014-12-01

Full Text Available Multi-camera networks have gained great interest in video-based surveillance systems for security monitoring, access control, etc. Person re-identification is an essential and challenging task in multi-camera networks, which aims to determine if a given individual has already appeared over the camera network. Individual recognition often uses faces as a trial and requires a large number of samples during the training phrase. This is difficult to fulfill due to the limitation of the camera hardware system and the unconstrained image capturing conditions. Conventional face recognition algorithms often encounter the “small sample size” (SSS problem arising from the small number of training samples compared to the high dimensionality of the sample space. To overcome this problem, interest in the combination of multiple base classifiers has sparked research efforts in ensemble methods. However, existing ensemble methods still open two questions: (1 how to define diverse base classifiers from the small data; (2 how to avoid the diversity/accuracy dilemma occurring during ensemble. To address these problems, this paper proposes a novel generic learning-based ensemble framework, which augments the small data by generating new samples based on a generic distribution and introduces a tailored 0–1 knapsack algorithm to alleviate the diversity/accuracy dilemma. More diverse base classifiers can be generated from the expanded face space, and more appropriate base classifiers are selected for ensemble. Extensive experimental results on four benchmarks demonstrate the higher ability of our system to cope with the SSS problem compared to the state-of-the-art system.

Recent advances in applications of nanomaterials for sample preparation.

Science.gov (United States)

Xu, Linnan; Qi, Xiaoyue; Li, Xianjiang; Bai, Yu; Liu, Huwei

2016-01-01

Sample preparation is a key step for qualitative and quantitative analysis of trace analytes in complicated matrix. Along with the rapid development of nanotechnology in material science, numerous nanomaterials have been developed with particularly useful applications in analytical chemistry. Benefitting from their high specific areas, increased surface activities, and unprecedented physical/chemical properties, the potentials of nanomaterials for rapid and efficient sample preparation have been exploited extensively. In this review, recent progress of novel nanomaterials applied in sample preparation has been summarized and discussed. Both nanoparticles and nanoporous materials are evaluated for their unusual performance in sample preparation. Various compositions and functionalizations extended the applications of nanomaterials in sample preparations, and distinct size and shape selectivity was generated from the diversified pore structures of nanoporous materials. Such great variety make nanomaterials a kind of versatile tools in sample preparation for almost all categories of analytes. Copyright © 2015 Elsevier B.V. All rights reserved.

Liquid scintillation: Sample preparation and counting atypical emissions

International Nuclear Information System (INIS)

Anon.

1991-01-01

Liquid scintillation sample preparation has the most published information but the least amount of definitive technical direction because the chemical and physical nature of the samples from biological investigations varies widely. This chapter discusses the following related topics: Aqueous Samples; Tissue Solubilizers; Absorption of 14 CO 2 ; Sample Combustion Methods; Heterogeneous Systems; Sample Preparation Problems (colored samples, chemiluminescence, photoluminescence, static electricity); Counting Various Types of Emitters; Counting Atypical Emissions. 2 refs., 2 figs

Comparison of generic-to-brand switchback patterns for generic and authorized generic drugs

Science.gov (United States)

Hansen, Richard A.; Qian, Jingjing; Berg, Richard; Linneman, James; Seoane-Vazquez, Enrique; Dutcher, Sarah K.; Raofi, Saeid; Page, C. David; Peissig, Peggy

2018-01-01

Background While generic drugs are therapeutically equivalent to brand drugs, some patients and healthcare providers remain uncertain about whether they produce identical outcomes. Authorized generics, which are identical in formulation to corresponding brand drugs but marketed as a generic, provide a unique post-marketing opportunity to study whether utilization patterns are influenced by perceptions of generic drugs. Objectives To compare generic-to-brand switchback rates between generics and authorized generics. Methods A retrospective cohort study was conducted using claims and electronic health records data from a regional U.S. healthcare system. Ten drugs with authorized generics and generics marketed between 1999 and 2014 were evaluated. Eligible adult patients received a brand drug during the 6 months preceding generic entry, and then switched to a generic or authorized generic. Patients in this cohort were followed for up to 30 months from the index switch date to evaluate occurrence of generic-to-brand switchbacks. Switchback rates were compared between patients on authorized generics versus generics using Kaplan-Meier curves and Cox proportional hazards models, controlling for individual drug effects, age, sex, Charlson comorbidity score, pre-index drug use characteristics, and pre-index healthcare utilization. Results Among 5,542 unique patients that switched from brand-to-generic or brand-to-authorized generic, 264 (4.8%) switched back to the brand drug. Overall switchback rates were similar for authorized generics compared with generics (HR=0.86; 95% CI 0.65-1.15). The likelihood of switchback was higher for alendronate (HR=1.64; 95% CI 1.20-2.23) and simvastatin (HR=1.81; 95% CI 1.30-2.54) and lower for amlodipine (HR=0.27; 95% CI 0.17-0.42) compared with other drugs in the cohort. Conclusions Overall switchback rates were similar between authorized generic and generic drug users, indirectly supporting similar efficacy and tolerability profiles for

Recent advances in column switching sample preparation in bioanalysis.

Science.gov (United States)

Kataoka, Hiroyuki; Saito, Keita

2012-04-01

Column switching techniques, using two or more stationary phase columns, are useful for trace enrichment and online automated sample preparation. Target fractions from the first column are transferred online to a second column with different properties for further separation. Column switching techniques can be used to determine the analytes in a complex matrix by direct sample injection or by simple sample treatment. Online column switching sample preparation is usually performed in combination with HPLC or capillary electrophoresis. SPE or turbulent flow chromatography using a cartridge column and in-tube solid-phase microextraction using a capillary column have been developed for convenient column switching sample preparation. Furthermore, various micro-/nano-sample preparation devices using new polymer-coating materials have been developed to improve extraction efficiency. This review describes current developments and future trends in novel column switching sample preparation in bioanalysis, focusing on innovative column switching techniques using new extraction devices and materials.

Modular microfluidic system for biological sample preparation

Science.gov (United States)

Rose, Klint A.; Mariella, Jr., Raymond P.; Bailey, Christopher G.; Ness, Kevin Dean

2015-09-29

A reconfigurable modular microfluidic system for preparation of a biological sample including a series of reconfigurable modules for automated sample preparation adapted to selectively include a) a microfluidic acoustic focusing filter module, b) a dielectrophoresis bacteria filter module, c) a dielectrophoresis virus filter module, d) an isotachophoresis nucleic acid filter module, e) a lyses module, and f) an isotachophoresis-based nucleic acid filter.

Applications of Liquid-Phase Microextraction in the Sample Preparation of Environmental Solid Samples

Directory of Open Access Journals (Sweden)

Helena Prosen

2014-05-01

Full Text Available Solvent extraction remains one of the fundamental sample preparation techniques in the analysis of environmental solid samples, but organic solvents are toxic and environmentally harmful, therefore one of the possible greening directions is its miniaturization. The present review covers the relevant research from the field of application of microextraction to the sample preparation of environmental solid samples (soil, sediments, sewage sludge, dust etc. published in the last decade. Several innovative liquid-phase microextraction (LPME techniques that have emerged recently have also been applied as an aid in sample preparation of these samples: single-drop microextraction (SDME, hollow fiber-liquid phase microextraction (HF-LPME, dispersive liquid-liquid microextraction (DLLME. Besides the common organic solvents, surfactants and ionic liquids are also used. However, these techniques have to be combined with another technique to release the analytes from the solid sample into an aqueous solution. In the present review, the published methods were categorized into three groups: LPME in combination with a conventional solvent extraction; LPME in combination with an environmentally friendly extraction; LPME without previous extraction. The applicability of these approaches to the sample preparation for the determination of pollutants in solid environmental samples is discussed, with emphasis on their strengths, weak points and environmental impact.

Applications of liquid-phase microextraction in the sample preparation of environmental solid samples.

Science.gov (United States)

Prosen, Helena

2014-05-23

Solvent extraction remains one of the fundamental sample preparation techniques in the analysis of environmental solid samples, but organic solvents are toxic and environmentally harmful, therefore one of the possible greening directions is its miniaturization. The present review covers the relevant research from the field of application of microextraction to the sample preparation of environmental solid samples (soil, sediments, sewage sludge, dust etc.) published in the last decade. Several innovative liquid-phase microextraction (LPME) techniques that have emerged recently have also been applied as an aid in sample preparation of these samples: single-drop microextraction (SDME), hollow fiber-liquid phase microextraction (HF-LPME), dispersive liquid-liquid microextraction (DLLME). Besides the common organic solvents, surfactants and ionic liquids are also used. However, these techniques have to be combined with another technique to release the analytes from the solid sample into an aqueous solution. In the present review, the published methods were categorized into three groups: LPME in combination with a conventional solvent extraction; LPME in combination with an environmentally friendly extraction; LPME without previous extraction. The applicability of these approaches to the sample preparation for the determination of pollutants in solid environmental samples is discussed, with emphasis on their strengths, weak points and environmental impact.

Indigenous development of automated metallographic sample preparation system

International Nuclear Information System (INIS)

Kulkarni, A.P.; Pandit, K.M.; Deshmukh, A.G.; Sahoo, K.C.

2005-01-01

Surface preparation of specimens for Metallographic studies on irradiated material involves a lot of remote handling of radioactive material by skilled manpower. These are laborious and man-rem intensive activities and put limitations on number of samples that can be prepared for the metallographic studies. To overcome these limitations, automated systems have been developed for surface preparation of specimens in PIE division. The system includes (i) Grinding and polishing stations (ii) Water jet cleaning station (iii) Ultrasonic cleaning stations (iv) Drying station (v) Sample loading and unloading station (vi) Dispenser for slurries and diluents and (vii) Automated head for movement of the sample holder disc from one station to other. System facilities the operator for programming/changing sequence of the sample preparations including remote changing of grinding/polishing discs from the stations. Two such systems have been installed and commissioned in Hot Cell for PIE Division. These are being used for preparation of irradiated samples from nuclear fuels and structural components. This development has increased the throughput of metallography work and savings in terms of (man-severts) radiation exposure to operators. This presentation will provide details of the challenges in undertaking this developmental work. (author)

Applications of Liquid-Phase Microextraction in the Sample Preparation of Environmental Solid Samples

OpenAIRE

Helena Prosen

2014-01-01

Solvent extraction remains one of the fundamental sample preparation techniques in the analysis of environmental solid samples, but organic solvents are toxic and environmentally harmful, therefore one of the possible greening directions is its miniaturization. The present review covers the relevant research from the field of application of microextraction to the sample preparation of environmental solid samples (soil, sediments, sewage sludge, dust etc.) published in the last decade. Several...

New materials for sample preparation techniques in bioanalysis.

Science.gov (United States)

Nazario, Carlos Eduardo Domingues; Fumes, Bruno Henrique; da Silva, Meire Ribeiro; Lanças, Fernando Mauro

2017-02-01

The analysis of biological samples is a complex and difficult task owing to two basic and complementary issues: the high complexity of most biological matrices and the need to determine minute quantities of active substances and contaminants in such complex sample. To succeed in this endeavor samples are usually subject to three steps of a comprehensive analytical methodological approach: sample preparation, analytes isolation (usually utilizing a chromatographic technique) and qualitative/quantitative analysis (usually with the aid of mass spectrometric tools). Owing to the complex nature of bio-samples, and the very low concentration of the target analytes to be determined, selective sample preparation techniques is mandatory in order to overcome the difficulties imposed by these two constraints. During the last decade new chemical synthesis approaches has been developed and optimized, such as sol-gel and molecularly imprinting technologies, allowing the preparation of novel materials for sample preparation including graphene and derivatives, magnetic materials, ionic liquids, molecularly imprinted polymers, and much more. In this contribution we will review these novel techniques and materials, as well as their application to the bioanalysis niche. Copyright © 2016 Elsevier B.V. All rights reserved.

Sample Preparation for Electron Probe Microanalysis-Pushing the Limits.

Science.gov (United States)

Geller, Joseph D; Engle, Paul D

2002-01-01

There are two fundamental considerations in preparing samples for electron probe microanalysis (EPMA). The first one may seem obvious, but we often find it is overlooked. That is, the sample analyzed should be representative of the population from which it comes. The second is a direct result of the assumptions in the calculations used to convert x-ray intensity ratios, between the sample and standard, to concentrations. Samples originate from a wide range of sources. During their journey to being excited under the electron beam for the production of x rays there are many possibilities for sample alteration. Handling can contaminate samples by adding extraneous matter. In preparation, the various abrasives used in sizing the sample by sawing, grinding and polishing can embed themselves. The most accurate composition of a contaminated sample is, at best, not representative of the original sample; it is misleading. Our laboratory performs EPMA analysis on customer submitted samples and prepares over 250 different calibration standards including pure elements, compounds, alloys, glasses and minerals. This large variety of samples does not lend itself to mass production techniques, including automatic polishing. Our manual preparation techniques are designed individually for each sample. The use of automated preparation equipment does not lend itself to this environment, and is not included in this manuscript. The final step in quantitative electron probe microanalysis is the conversion of x-ray intensities ratios, known as the "k-ratios," to composition (in mass fraction or atomic percent) and/or film thickness. Of the many assumptions made in the ZAF (where these letters stand for atomic number, absorption and fluorescence) corrections the localized geometry between the sample and electron beam, or takeoff angle, must be accurately known. Small angular errors can lead to significant errors in the final results. The sample preparation technique then becomes very

Preparation of honey sample for tritium monitoring

International Nuclear Information System (INIS)

Chen Bingru; Wang Chenlian; Wang Weihua

1989-01-01

The method of preparation of honey sample for tritium monitoring was described. The equipments consist of an air and honey supply system, a quartz combustor with CM-type monolithic combustion catalyst and a condensation system. In the equipments, honey sample was converted into cooling water by the distilling, cracking and carbonizing procedures for tritium counting. The recovery ratio is 99.0 ± 4.5 percent for tritiated water and 96.0 ± 2.0 for tritiated organic compounds. It is a feasible preparing method for the total tritium monitoring in honey sample

Platelet-rich fibrin prepared from stored whole-blood samples.

Science.gov (United States)

Isobe, Kazushige; Suzuki, Masashi; Watanabe, Taisuke; Kitamura, Yutaka; Suzuki, Taiji; Kawabata, Hideo; Nakamura, Masayuki; Okudera, Toshimitsu; Okudera, Hajime; Uematsu, Kohya; Nakata, Koh; Tanaka, Takaaki; Kawase, Tomoyuki

2017-12-01

In regenerative therapy, self-clotted platelet concentrates, such as platelet-rich fibrin (PRF), are generally prepared on-site and are immediately used for treatment. If blood samples or prepared clots can be preserved for several days, their clinical applicability will expand. Here, we prepared PRF from stored whole-blood samples and examined their characteristics. Blood samples were collected from non-smoking, healthy male donors (aged 27-67 years, N = 6), and PRF clots were prepared immediately or after storage for 1-2 days. Fibrin fiber was examined by scanning electron microscopy. Bioactivity was evaluated by means of a bioassay system involving human periosteal cells, whereas PDGF-BB concentrations were determined by an enzyme-linked immunosorbent assay. Addition of optimal amounts of a 10% CaCl 2 solution restored the coagulative ability of whole-blood samples that contained an anticoagulant (acid citrate dextrose) and were stored for up to 2 days at ambient temperature. In PRF clots prepared from the stored whole-blood samples, the thickness and cross-links of fibrin fibers were almost identical to those of freshly prepared PRF clots. PDGF-BB concentrations in the PRF extract were significantly lower in stored whole-blood samples than in fresh samples; however, both extracts had similar stimulatory effects on periosteal-cell proliferation. Quality of PRF clots prepared from stored whole-blood samples is not reduced significantly and can be ensured for use in regenerative therapy. Therefore, the proposed method enables a more flexible treatment schedule and choice of a more suitable platelet concentrate immediately before treatment, not after blood collection.

The effect of sample preparation on uranium hydriding

International Nuclear Information System (INIS)

Banos, A.; Stitt, C.A.; Scott, T.B.

2016-01-01

Highlights: • Distinct differences in uranium hydride growth rates and characteristics between different surface preparation methods. • The primary difference between the categories of sample preparations is the level of strain present in the surface. • Greater surface-strain, leads to higher nucleation number density, implying a preferred attack of strained vs unstrained metal. • As strain is reduced, surface features such as carbides and grain boundaries become more important in controlling the UH3 location. - Abstract: The influence of sample cleaning preparation on the early stages of uranium hydriding has been examined, by using four identical samples but concurrently prepared using four different methods. The samples were reacted together in the same corrosion cell to ensure identical exposure conditions. From the analysis, it was found that the hydride nucleation rate was proportional to the level of strain exhibiting higher number density for the more strained surfaces. Additionally, microstructure of the metal plays a secondary role regarding initial hydrogen attack on the highly strained surfaces yet starts to dominate the system while moving to more pristine samples.

43 CFR Appendix A to Part 10 - Sample Summary

Science.gov (United States)

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Sample Summary A Appendix A to Part 10... REPATRIATION REGULATIONS Pt. 10, App. A Appendix A to Part 10—Sample Summary The following is a generic sample and should be used as a guideline for preparation of summaries tailoring the information to the...

Efficient sample preparation from complex biological samples using a sliding lid for immobilized droplet extractions.

Science.gov (United States)

Casavant, Benjamin P; Guckenberger, David J; Beebe, David J; Berry, Scott M

2014-07-01

Sample preparation is a major bottleneck in many biological processes. Paramagnetic particles (PMPs) are a ubiquitous method for isolating analytes of interest from biological samples and are used for their ability to thoroughly sample a solution and be easily collected with a magnet. There are three main methods by which PMPs are used for sample preparation: (1) removal of fluid from the analyte-bound PMPs, (2) removal of analyte-bound PMPs from the solution, and (3) removal of the substrate (with immobilized analyte-bound PMPs). In this paper, we explore the third and least studied method for PMP-based sample preparation using a platform termed Sliding Lid for Immobilized Droplet Extractions (SLIDE). SLIDE leverages principles of surface tension and patterned hydrophobicity to create a simple-to-operate platform for sample isolation (cells, DNA, RNA, protein) and preparation (cell staining) without the need for time-intensive wash steps, use of immiscible fluids, or precise pinning geometries. Compared to other standard isolation protocols using PMPs, SLIDE is able to perform rapid sample preparation with low (0.6%) carryover of contaminants from the original sample. The natural recirculation occurring within the pinned droplets of SLIDE make possible the performance of multistep cell staining protocols within the SLIDE by simply resting the lid over the various sample droplets. SLIDE demonstrates a simple easy to use platform for sample preparation on a range of complex biological samples.

On the development of automatic sample preparation devices

International Nuclear Information System (INIS)

Oesselmann, J.

1987-01-01

Modern mass spectrometers for stable isotope analysis offer accurate isotope ratio results from gaseous samples (CO 2 , N 2 , H 2 , SO 2 ) in a completely automated fashion. However, most samples of interest either are associated with contaminant gases or the gas has to be liberated by a chemical procedure prior to measurement. In most laboratories this sample preparation step is performed manually. As a consequence, sample throughput is rather low and - despite skilful operation - the preparation procedure varies slightly from one sample to the next affecting mainly the reproducibility of the data. (author)

Sample Preparation for Electron Probe Microanalysis—Pushing the Limits

Science.gov (United States)

Geller, Joseph D.; Engle, Paul D.

2002-01-01

There are two fundamental considerations in preparing samples for electron probe microanalysis (EPMA). The first one may seem obvious, but we often find it is overlooked. That is, the sample analyzed should be representative of the population from which it comes. The second is a direct result of the assumptions in the calculations used to convert x-ray intensity ratios, between the sample and standard, to concentrations. Samples originate from a wide range of sources. During their journey to being excited under the electron beam for the production of x rays there are many possibilities for sample alteration. Handling can contaminate samples by adding extraneous matter. In preparation, the various abrasives used in sizing the sample by sawing, grinding and polishing can embed themselves. The most accurate composition of a contaminated sample is, at best, not representative of the original sample; it is misleading. Our laboratory performs EPMA analysis on customer submitted samples and prepares over 250 different calibration standards including pure elements, compounds, alloys, glasses and minerals. This large variety of samples does not lend itself to mass production techniques, including automatic polishing. Our manual preparation techniques are designed individually for each sample. The use of automated preparation equipment does not lend itself to this environment, and is not included in this manuscript. The final step in quantitative electron probe microanalysis is the conversion of x-ray intensities ratios, known as the “k-ratios,” to composition (in mass fraction or atomic percent) and/or film thickness. Of the many assumptions made in the ZAF (where these letters stand for atomic number, absorption and fluorescence) corrections the localized geometry between the sample and electron beam, or takeoff angle, must be accurately known. Small angular errors can lead to significant errors in the final results. The sample preparation technique then becomes very

Low-mass molecular dynamics simulation: A simple and generic technique to enhance configurational sampling

Energy Technology Data Exchange (ETDEWEB)

Pang, Yuan-Ping, E-mail: pang@mayo.edu

2014-09-26

Highlights: • Reducing atomic masses by 10-fold vastly improves sampling in MD simulations. • CLN025 folded in 4 of 10 × 0.5-μs MD simulations when masses were reduced by 10-fold. • CLN025 folded as early as 96.2 ns in 1 of the 4 simulations that captured folding. • CLN025 did not fold in 10 × 0.5-μs MD simulations when standard masses were used. • Low-mass MD simulation is a simple and generic sampling enhancement technique. - Abstract: CLN025 is one of the smallest fast-folding proteins. Until now it has not been reported that CLN025 can autonomously fold to its native conformation in a classical, all-atom, and isothermal–isobaric molecular dynamics (MD) simulation. This article reports the autonomous and repeated folding of CLN025 from a fully extended backbone conformation to its native conformation in explicit solvent in multiple 500-ns MD simulations at 277 K and 1 atm with the first folding event occurring as early as 66.1 ns. These simulations were accomplished by using AMBER forcefield derivatives with atomic masses reduced by 10-fold on Apple Mac Pros. By contrast, no folding event was observed when the simulations were repeated using the original AMBER forcefields of FF12SB and FF14SB. The results demonstrate that low-mass MD simulation is a simple and generic technique to enhance configurational sampling. This technique may propel autonomous folding of a wide range of miniature proteins in classical, all-atom, and isothermal–isobaric MD simulations performed on commodity computers—an important step forward in quantitative biology.

Comparison of Generic-to-Brand Switchback Rates Between Generic and Authorized Generic Drugs.

Science.gov (United States)

Hansen, Richard A; Qian, Jingjing; Berg, Richard; Linneman, James; Seoane-Vazquez, Enrique; Dutcher, Sarah K; Raofi, Saeid; Page, C David; Peissig, Peggy

2017-04-01

Generic drugs contain identical active ingredients as their corresponding brand drugs and are pharmaceutically equivalent and bioequivalent, whereas authorized generic drugs (AGs) contain both identical active and inactive ingredients as their corresponding brand drugs but are marketed as generics. This study compares generic-to-brand switchback rates between generic and AGs. Retrospective cohort study. Claims and electronic health record data from a regional U.S. health care system. The full cohort consisted of 5542 unique patients who received select branded drugs during the 6 months prior to their generic drug market availability (between 1999 and 2014) and then were switched to an AG or generic drug within 30 months of generic drug entry. For these patients, 5929 unique patient-drug combinations (867 with AGs and 5062 with generic drugs) were evaluated. Ten drugs with AGs and generics marketed between 1999 and 2014 were evaluated. The date of the first generic prescription was considered the index date for each drug, and it marked the beginning of follow-up to evaluate the occurrence of generic-to-brand switchback patterns over the subsequent 30 months. Switchback rates were compared between patients receiving AGs versus those receiving generics using multivariable Cox proportional hazards models, controlling for individual drug effects, age, sex, Charlson Comorbidity Score, pre-index drug use characteristics, and pre-index health care utilization. Among the 5542 unique patients who switched from brand to generic or brand to AG, 264 (4.8%) switched back to the brand drug. Overall switchback rates were similar for AGs compared with generics (hazard ratio [HR] 0.86, 95% confidence interval [CI] 0.65-1.15). The likelihood of switchback was higher for alendronate (HR 1.64, 95% CI 1.20-2.23) and simvastatin (HR 1.81, 95% CI 1.30-2.54) and lower for amlodipine (HR 0.27, 95% CI 0.17-0.42) compared with the other drugs evaluated. Overall switchback rates were similar

40 CFR 205.160-2 - Test sample selection and preparation.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Test sample selection and preparation... sample selection and preparation. (a) Vehicles comprising the sample which are required to be tested... maintained in any manner unless such preparation, tests, modifications, adjustments or maintenance are part...

FISHprep: A Novel Integrated Device for Metaphase FISH Sample Preparation

DEFF Research Database (Denmark)

Shah, Pranjul Jaykumar; Vedarethinam, Indumathi; Kwasny, Dorota

2011-01-01

We present a novel integrated device for preparing metaphase chromosomes spread slides (FISHprep). The quality of cytogenetic analysis from patient samples greatly relies on the efficiency of sample pre-treatment and/or slide preparation. In cytogenetic slide preparation, cell cultures...... are routinely used to process samples (for culture, arrest and fixation of cells) and/or to expand limited amount of samples (in case of prenatal diagnostics). Arguably, this expansion and other sample pretreatments form the longest part of the entire diagnostic protocols spanning over 3–4 days. We present here...... with minimal handling for metaphase FISH slide preparation....

Independent assessment of matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) sample preparation quality: Effect of sample preparation on MALDI-MS of synthetic polymers.

Science.gov (United States)

Kooijman, Pieter C; Kok, Sander; Honing, Maarten

2017-02-28

Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) provides detailed and in-depth information about the molecular characteristics of synthetic polymers. To obtain the most accurate results the sample preparation parameters should be chosen to suit the sample and the aim of the experiment. Because the underlying principles of MALDI are still not fully known, a priori determination of optimal sample preparation protocols is often not possible. Employing an automated sample preparation quality assessment method recently presented by us we quantified the sample preparation quality obtained using various sample preparation protocols. Six conventional matrices with and without added potassium as a cationization agent and six ionic liquid matrices (ILMs) were assessed using poly(ethylene glycol) (PEG), polytetrahydrofuran (PTHF) and poly(methyl methacrylate) (PMMA) as samples. All sample preparation protocols were scored and ranked based on predefined quality parameters and spot-to-spot repeatability. Clearly distinctive preferences were observed in matrix identity and cationization agent for PEG, PTHF and PMMA, as the addition of an excess of potassium cationization agent results in an increased score for PMMA and a contrasting matrix-dependent effect for PTHF and PEG. The addition of excess cationization agent to sample mixtures dissipates any overrepresentation of high molecular weight polymer species. Our results show reduced ionization efficiency and similar sample deposit homogeneity for all tested ILMs, compared with well-performing conventional MALDI matrices. The results published here represent a start in the unsupervised quantification of sample preparation quality for MALDI samples. This method can select the best sample preparation parameters for any synthetic polymer sample and the results can be used to formulate hypotheses on MALDI principles. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Congener Production in Blood Samples During Preparation and Storage

DEFF Research Database (Denmark)

Felby, Søren; Nielsen, Erik

1995-01-01

Retsmedicin, congener production, preparation, head space GC, acetone, isobutanol, storage, blood samples, n-propanol, methanol, methylethylketone......Retsmedicin, congener production, preparation, head space GC, acetone, isobutanol, storage, blood samples, n-propanol, methanol, methylethylketone...

Trends in sample preparation 2002. Development and application. Book of abstracts

International Nuclear Information System (INIS)

Wenzl, T.; Eberl, M.; Zischka, M.; Knapp, G.

2002-01-01

This conference comprised topics dealing with sample preparation such as: sample decomposition, solvent extraction, derivatization techniques and uncertainty in sample preparation. In particular microwave assisted sample preparation techniques and equipment were discussed. The papers were organized under the general topics: trace element analysis, trace analysis of organic compounds, high performance instrumentation in sample preparation, speciation analysis and posters session. Those papers of INIS interest are cited individually. (nevyjel)

Trends in sample preparation 2002. Development and application. Book of abstracts

Energy Technology Data Exchange (ETDEWEB)

Wenzl, T; Eberl, M; Zischka, M; Knapp, G [eds.

2002-07-01

This conference comprised topics dealing with sample preparation such as: sample decomposition, solvent extraction, derivatization techniques and uncertainty in sample preparation. In particular microwave assisted sample preparation techniques and equipment were discussed. The papers were organized under the general topics: trace element analysis, trace analysis of organic compounds, high performance instrumentation in sample preparation, speciation analysis and posters session. Those papers of INIS interest are cited individually. (nevyjel)

On-line Automated Sample Preparation-Capillary Gas Chromatography for the Analysis of Plasma Samples.

NARCIS (Netherlands)

Louter, A.J.H.; van der Wagt, R.A.C.A.; Brinkman, U.A.T.

1995-01-01

An automated sample preparation module, (the automated sample preparation with extraction columns, ASPEC), was interfaced with a capillary gas chromatograph (GC) by means of an on-column interface. The system was optimised for the determination of the antidepressant trazodone in plasma. The clean-up

Cr(VI) generation during sample preparation of solid samples – A ...

African Journals Online (AJOL)

Cr(VI) generation during sample preparation of solid samples – A chromite ore case study. R.I Glastonbury, W van der Merwe, J.P Beukes, P.G van Zyl, G Lachmann, C.J.H Steenkamp, N.F Dawson, M.H Stewart ...

Current trends in sample preparation for cosmetic analysis.

Science.gov (United States)

Zhong, Zhixiong; Li, Gongke

2017-01-01

The widespread applications of cosmetics in modern life make their analysis particularly important from a safety point of view. There is a wide variety of restricted ingredients and prohibited substances that primarily influence the safety of cosmetics. Sample preparation for cosmetic analysis is a crucial step as the complex matrices may seriously interfere with the determination of target analytes. In this review, some new developments (2010-2016) in sample preparation techniques for cosmetic analysis, including liquid-phase microextraction, solid-phase microextraction, matrix solid-phase dispersion, pressurized liquid extraction, cloud point extraction, ultrasound-assisted extraction, and microwave digestion, are presented. Furthermore, the research and progress in sample preparation techniques and their applications in the separation and purification of allowed ingredients and prohibited substances are reviewed. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Recent Developments in Sample Preparation for Mass Spectrometry-Based Metabolomics.

Science.gov (United States)

Gong, Zhi-Gang; Hu, Jing; Wu, Xi; Xu, Yong-Jiang

2017-07-04

Metabolomics is a critical member in systems biology. Although great progress has been achieved in metabolomics, there are still some problems in sample preparation, data processing and data interpretation. In this review, we intend to explore the roles, challenges and trends in sample preparation for mass spectrometry- (MS-) based metabolomics. The newly emerged sample preparation methods were also critically examined, including laser microdissection, in vivo sampling, dried blood spot, microwave, ultrasound and enzyme-assisted extraction, as well as microextraction techniques. Finally, we provide some conclusions and perspectives for sample preparation in MS-based metabolomics.

Factors influencing anti-asthmatic generic drug consumption in Morocco: 1999-2010.

Science.gov (United States)

Ghanname, Imane; Ahid, Samir; Berrada, Ghizlane; Belaiche, Abdelmjid; Hassar, Mohammed; Cherrah, Yahia

2014-01-01

The increasing availability of generic drugs (GD) resulted in a remarkable reduction in treatment costs that allowed a better access to health care.The aim of this study is to evaluate the share of anti-asthmatic generic drugs during the period 1999-2010 in Morocco and to look at the factors influencing generic development. In this study, we used Moroccan sales data from IMS Health (Intercontinental Marketing Services). The consumption of the drugs was expressed in DDD/1000 inhabitants/day according to the WHO ATC/DDD methodology. Between 1999 and 2010, anti-asthmatic consumption increased from 3.91 to 14.43 DDD/1000 inhabitants/day. The market of anti-asthmatic generic drugs progressed from 1.83 (47%) to 2.18 (23%) DDD/1000 inhabitants/day from 1999 to 2010. In 2010, inhaled glucocorticosteroids ranked first (0.83 DDD/1000 inhabitants/day), followed by inhaled short acting beta agonists (0.73 DDD/1000 inhabitants/day). The number of brands went from 27 in 1999 to 34 in 2010, with a generic share increasing from 55.55% to 70.59%. The number of anti-asthmatic pharmaceutical preparations increased from 57 to 64 during the same period, of which 31 and 42 were generic preparations. In 2010, the total cost of anti-asthmatic dugs was about 22 million euro, the generics representing 14 million euro. Despite the introduction of a compulsory insurance scheme called "AMO", that allows a refund for 69.5% of anti-asthmatic specialties marketed in Morocco, anti-asthmatic generic drug consumption remains limited. The Moroccan market is still largely dominated by the originator drugs with still valid patents.

Soil sample preparation using microwave digestion for uranium analysis

International Nuclear Information System (INIS)

Mohagheghi, Amir H.; Preston, Rose; Akbarzadeh, Mansoor; Bakthiar, Steven

2000-01-01

A new sample preparation procedure has been developed for digestion of soil samples for uranium analysis. The technique employs a microwave oven digestion system to digest the sample and to prepare it for separation chemistry and analysis. The method significantly reduces the volume of acids used, eliminates a large fraction of acid vapor emissions, and speeds up the analysis time. The samples are analyzed by four separate techniques: Gamma Spectrometry, Alpha Spectroscopy using the open digestion method, Kinetic Phosphorescence Analysis (KPA) using open digestion, and KPA by Microwave digestion technique. The results for various analytical methods are compared and used to confirm the validity of the new procedure. The details of the preparation technique along with its benefits are discussed

7 CFR 61.34 - Drawing and preparation of sample.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Drawing and preparation of sample. 61.34 Section 61.34 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Cottonseed Samplers § 61.34 Drawing and preparation of sample. Each licensed cottonseed sampler shall draw...

Generic medicines: Perceptions of Physicians in Basrah, Iraq

Directory of Open Access Journals (Sweden)

Adheed Khalid Sharrad

2009-08-01

Full Text Available BackgroundThe use of cheaper generic medicines is a strategy promotedin many countries to reduce rising health care costs. The aimof this study was to explore factors affecting generic medicineprescribing by physicians in Basrah, Iraq.MethodologyA purposive sample of ten physicians practicing in Basrahwas interviewed using a semi-structured interview guide.ResultsAnalysis of the interviews identified seven major themes:medicine prescribing practice, knowledge of therapeuticequivalency of generic medicine, patients’ acceptance ofgeneric medicine, counterfeit medicine, drug informationsource and effect of drug advertising on medicines choice,brand substitution practice by community pharmacists, and,finally strategies to improve generic medicine usefulness.Participants identified helpful strategies to increase genericprescribing including; physician and patient education ongeneric medicine; persuading physicians about the safety andefficacy of generic medicines; and finally educating seniormedical students on generic prescribing.ConclusionThe data suggest that participants were enthusiasticabout prescribing generic medicines. However physiciansinsist that pharmacists should not be allowed tosubstitute generic drugs without prior approval ofdoctors.

A pilot study to evaluate the application of a generic protein standard panel for quality control of biomarker detection technologies

Directory of Open Access Journals (Sweden)

Valdivia Hernan J

2011-08-01

Full Text Available Abstract Background Protein biomarker studies are currently hampered by a lack of measurement standards to demonstrate quality, reliability and comparability across multiple assay platforms. This is especially pertinent for immunoassays where multiple formats for detecting target analytes are commonly used. Findings In this pilot study a generic panel of six non-human protein standards (50 - 10^7 pg/mL of varying abundance was prepared as a quality control (QC material. Simulated "normal" and "diseased" panels of proteins were prepared in pooled human plasma and incorporated into immunoassays using the Meso Scale Discovery® (MSD® platform to illustrate reliable detection of the component proteins. The protein panel was also evaluated as a spike-in material for a model immunoassay involving detection of ovarian cancer biomarkers within individual human plasma samples. Our selected platform could discriminate between two panels of the proteins exhibiting small differences in abundance. Across distinct experiments, all component proteins exhibited reproducible signal outputs in pooled human plasma. When individual donor samples were used, half the proteins produced signals independent of matrix effects. These proteins may serve as a generic indicator of platform reliability. Each of the remaining proteins exhibit differential signals across the distinct samples, indicative of sample matrix effects, with the three proteins following the same trend. This subset of proteins may be useful for characterising the degree of matrix effects associated with the sample which may impact on the reliability of quantifying target diagnostic biomarkers. Conclusions We have demonstrated the potential utility of this panel of standards to act as a generic QC tool for evaluating the reproducibility of the platform for protein biomarker detection independent of serum matrix effects.

New trends in sample preparation techniques for environmental analysis.

Science.gov (United States)

Ribeiro, Cláudia; Ribeiro, Ana Rita; Maia, Alexandra S; Gonçalves, Virgínia M F; Tiritan, Maria Elizabeth

2014-01-01

Environmental samples include a wide variety of complex matrices, with low concentrations of analytes and presence of several interferences. Sample preparation is a critical step and the main source of uncertainties in the analysis of environmental samples, and it is usually laborious, high cost, time consuming, and polluting. In this context, there is increasing interest in developing faster, cost-effective, and environmentally friendly sample preparation techniques. Recently, new methods have been developed and optimized in order to miniaturize extraction steps, to reduce solvent consumption or become solventless, and to automate systems. This review attempts to present an overview of the fundamentals, procedure, and application of the most recently developed sample preparation techniques for the extraction, cleanup, and concentration of organic pollutants from environmental samples. These techniques include: solid phase microextraction, on-line solid phase extraction, microextraction by packed sorbent, dispersive liquid-liquid microextraction, and QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe).

Tooth enamel sample preparation using alkaline treatment in ESR dosimetry

International Nuclear Information System (INIS)

Yongzeng, Zhou; Jiadong, Wang; Xiaomei, Jia; Ke, Wu; Jianbo, Cong

2002-01-01

Tooth enamel sample preparation using alkaline treatment was studied and compared with traditional mechanical method in this paper. 20 adult teeth were used. Samples were placed into NaOH solution. This method requires 4-5 weeks and the enamel was separated from dentin. Experimental results show that 8M NaOH was appropriate for separating enamel from dentin and that there is no difference in background signal relative intensity between samples prepared by mechanical and by chemical methods. There is also no difference in radiosensitivity between samples prepared by two methods mentioned above. Dose response curve for tooth enamel samples isolated by 8M NaOH solution was obtained

Sample preparation for special PIE-techniques at ITU

International Nuclear Information System (INIS)

Toscano, E.H.; Manzel, R.

2002-01-01

Several sample preparation techniques were developed and installed in hot cells. The techniques were conceived to evaluate the performance of highly burnt fuel rods and include: (a) a device for the removal of the fuel, (b) a method for the preparation of the specimen ends for the welding of new end caps and for the careful cleaning of samples for Transmission Electron Microscopy and Glow Discharge Mass Spectroscopy, (c) a sample pressurisation device for long term creep tests, and (d) a diameter measuring device for creep or burst samples. Examples of the determination of the mechanical properties, the behaviour under transient conditions and for the assessment of the corrosion behaviour of high burnup cladding materials are presented. (author)

High-throughput automated microfluidic sample preparation for accurate microbial genomics.

Science.gov (United States)

Kim, Soohong; De Jonghe, Joachim; Kulesa, Anthony B; Feldman, David; Vatanen, Tommi; Bhattacharyya, Roby P; Berdy, Brittany; Gomez, James; Nolan, Jill; Epstein, Slava; Blainey, Paul C

2017-01-27

Low-cost shotgun DNA sequencing is transforming the microbial sciences. Sequencing instruments are so effective that sample preparation is now the key limiting factor. Here, we introduce a microfluidic sample preparation platform that integrates the key steps in cells to sequence library sample preparation for up to 96 samples and reduces DNA input requirements 100-fold while maintaining or improving data quality. The general-purpose microarchitecture we demonstrate supports workflows with arbitrary numbers of reaction and clean-up or capture steps. By reducing the sample quantity requirements, we enabled low-input (∼10,000 cells) whole-genome shotgun (WGS) sequencing of Mycobacterium tuberculosis and soil micro-colonies with superior results. We also leveraged the enhanced throughput to sequence ∼400 clinical Pseudomonas aeruginosa libraries and demonstrate excellent single-nucleotide polymorphism detection performance that explained phenotypically observed antibiotic resistance. Fully-integrated lab-on-chip sample preparation overcomes technical barriers to enable broader deployment of genomics across many basic research and translational applications.

Generic medications for you, but brand-name medications for me.

Science.gov (United States)

Keenum, Amy J; Devoe, Jennifer E; Chisolm, Deena J; Wallace, Lorraine S

2012-01-01

Because generic medications are less expensive than brand-name medications, government and private insurers have encouraged and/or mandated the use of generics. This study aimed at evaluating perceptions about generic medications among English-speaking women of childbearing age currently enrolled in U.S. TennCare (Medicaid). We recruited a convenience sample of patients from the waiting room of a primary care/gynecology health clinic, with 80% recruitment rate among those approached. We orally administered a 25-item questionnaire to gather sociodemographic information and to assess beliefs regarding the efficacy, safety, cost, and preferences for personal use of generic medications. The average age of the women (n=172) was 28.8 ± 6.4 years, and most were white (82.0%) and currently married (58.1%). Nearly one-fifth (19.2%) had not completed high school. Most women believed that generic medications were less expensive (97.6%) and better value (60.5%) than brand-name medications, but only 45.3% preferred to take generics themselves. About a quarter (23.3%) believed that brand-name medications were more effective than generics, whereas 13.4% believed that generics caused more side effects. Few women reported that their doctor (29.7%) and/or pharmacist (35.5%) had ever talked to them about taking generics. Awareness of the benefits of generics did not equal preferences for personal use of generics among this sample of women enrolled in U.S. TennCare. Furthermore, women reported that providers-both physicians and pharmacists-infrequently discussed generic substitution with them. Copyright © 2012 Elsevier Inc. All rights reserved.

Sample preparations for spark source mass spectrography

International Nuclear Information System (INIS)

Catlett, C.W.; Rollins, M.B.; Griffin, E.B.; Dorsey, J.G.

1977-10-01

Methods have been developed for the preparation of various materials for spark source mass spectrography. The essential features of these preparations (all which can provide adequate precision in a cost-effective manner) consist in obtaining spark-stable electrode sample pieces, a common matrix, a reduction of anomolous effects in the spark, the incorporation of a suitable internal standard for plate response normalization, and a reduction in time

Present status of NMCC and sample preparation method for bio-samples

International Nuclear Information System (INIS)

Futatsugawa, S.; Hatakeyama, S.; Saitou, S.; Sera, K.

1993-01-01

In NMCC(Nishina Memorial Cyclotron Center) we are doing researches on PET of nuclear medicine (Positron Emission Computed Tomography) and PIXE analysis (Particle Induced X-ray Emission) using a small cyclotron of compactly designed. The NMCC facilities have been opened to researchers of other institutions since April 1993. The present status of NMCC is described. Bio-samples (medical samples, plants, animals and environmental samples) have mainly been analyzed by PIXE in NMCC. Small amounts of bio-samples for PIXE are decomposed quickly and easily in a sealed PTFE (polytetrafluoroethylene) vessel with a microwave oven. This sample preparation method of bio-samples also is described. (author)

Finding even more anthropogenic indicators in mildly prepared sediment samples

DEFF Research Database (Denmark)

Enevold, Renée; Odgaard, Bent Vad

2016-01-01

be worth the effort to prepare the NPP samples with as mild a preparation method as possible. We have mildly prepared NPP samples from a small forest hollow, Tårup Lund, Denmark. From the recovered NPP assemblages we attempt identifying anthropogenic indicators by comparing to the environmental information......NPPs in anthropogenic soils and archaeological samples are often numerous in types as well as in abundance. Preparing these soil samples with methods based on acid digestion holds the potential of severe bias leaving the NPP assemblages devoid of acid vulnerable NPPs. In many cases it might...... derived from sediment, pollen and macrofossil analyses. The sediment from the forest hollow encompasses environmental information from the last 6000 years, including a period of locally intense pastoral and/or agricultural activity during the Iron Age. Keywords: NPP diversity, forest hollow, anthropogenic...

Sampling, storage and sample preparation procedures for X ray fluorescence analysis of environmental materials

International Nuclear Information System (INIS)

1997-06-01

X ray fluorescence (XRF) method is one of the most commonly used nuclear analytical technique because of its multielement and non-destructive character, speed, economy and ease of operation. From the point of view of quality assurance practices, sampling and sample preparation procedures are the most crucial steps in all analytical techniques, (including X ray fluorescence) applied for the analysis of heterogeneous materials. This technical document covers recent modes of the X ray fluorescence method and recent developments in sample preparation techniques for the analysis of environmental materials. Refs, figs, tabs

Influences of different sample preparation methods on tooth enamel ESR signals

International Nuclear Information System (INIS)

Zhang Wenyi; Jiao Ling; Zhang Liang'an; Pan Zhihong; Zeng Hongyu

2005-01-01

Objective: To study the influences of different sample preparation methods on tooth enamel ESR signals in order to reduce the effect of dentine on their sensitivities to radiation. Methods: The enamel was separated from dentine of non-irradiated adult teeth by mechanical, chemical, or both methods. The samples of different preparations were scanned by an ESR spectrometer before and after irradiation. Results: The response of ESR signals of samples prepared with different methods to radiation dose was significantly different. Conclusion: The selection of sample preparation method is very important for dose reconstruction by tooth enamel ESR dosimetry, especially in the low dose range. (authors)

Global metabolite analysis of yeast: evaluation of sample preparation methods

DEFF Research Database (Denmark)

Villas-Bôas, Silas Granato; Højer-Pedersen, Jesper; Åkesson, Mats Fredrik

2005-01-01

Sample preparation is considered one of the limiting steps in microbial metabolome analysis. Eukaryotes and prokaryotes behave very differently during the several steps of classical sample preparation methods for analysis of metabolites. Even within the eukaryote kingdom there is a vast diversity...

Fluidics platform and method for sample preparation and analysis

Science.gov (United States)

Benner, W. Henry; Dzenitis, John M.; Bennet, William J.; Baker, Brian R.

2014-08-19

Herein provided are fluidics platform and method for sample preparation and analysis. The fluidics platform is capable of analyzing DNA from blood samples using amplification assays such as polymerase-chain-reaction assays and loop-mediated-isothermal-amplification assays. The fluidics platform can also be used for other types of assays and analyzes. In some embodiments, a sample in a sealed tube can be inserted directly. The following isolation, detection, and analyzes can be performed without a user's intervention. The disclosed platform may also comprises a sample preparation system with a magnetic actuator, a heater, and an air-drying mechanism, and fluid manipulation processes for extraction, washing, elution, assay assembly, assay detection, and cleaning after reactions and between samples.

Combining Electrochemical Sensors with Miniaturized Sample Preparation for Rapid Detection in Clinical Samples

Science.gov (United States)

Bunyakul, Natinan; Baeumner, Antje J.

2015-01-01

Clinical analyses benefit world-wide from rapid and reliable diagnostics tests. New tests are sought with greatest demand not only for new analytes, but also to reduce costs, complexity and lengthy analysis times of current techniques. Among the myriad of possibilities available today to develop new test systems, amperometric biosensors are prominent players—best represented by the ubiquitous amperometric-based glucose sensors. Electrochemical approaches in general require little and often enough only simple hardware components, are rugged and yet provide low limits of detection. They thus offer many of the desirable attributes for point-of-care/point-of-need tests. This review focuses on investigating the important integration of sample preparation with (primarily electrochemical) biosensors. Sample clean up requirements, miniaturized sample preparation strategies, and their potential integration with sensors will be discussed, focusing on clinical sample analyses. PMID:25558994

Impact of generic substitution decision support on electronic prescribing behavior.

Science.gov (United States)

Stenner, Shane P; Chen, Qingxia; Johnson, Kevin B

2010-01-01

To evaluate the impact of generic substitution decision support on electronic (e-) prescribing of generic medications. The authors analyzed retrospective outpatient e-prescribing data from an academic medical center and affiliated network for July 1, 2005-September 30, 2008 using an interrupted time-series design to assess the rate of generic prescribing before and after implementing generic substitution decision support. To assess background secular trends, e-prescribing was compared with a concurrent random sample of hand-generated prescriptions. Proportion of generic medications prescribed before and after the intervention, evaluated over time, and compared with a sample of prescriptions generated without e-prescribing. The proportion of generic medication prescriptions increased from 32.1% to 54.2% after the intervention (22.1% increase, 95% CI 21.9% to 22.3%), with no diminution in magnitude of improvement post-intervention. In the concurrent control group, increases in proportion of generic prescriptions (29.3% to 31.4% to 37.4% in the pre-intervention, post-intervention, and end-of-study periods, respectively) were not commensurate with the intervention. There was a larger change in generic prescribing rates among authorized prescribers (24.6%) than nurses (18.5%; adjusted OR 1.38, 95% CI 1.17 to 1.63). Two years after the intervention, the proportion of generic prescribing remained significantly higher for e-prescriptions (58.1%; 95% CI 57.5% to 58.7%) than for hand-generated prescriptions ordered at the same time (37.4%; 95% CI 34.9% to 39.9%) (p<0.0001). Generic prescribing increased significantly in every specialty. Implementation of generic substitution decision support was associated with dramatic and sustained improvements in the rate of outpatient generic e-prescribing across all specialties.

Sample preparation techniques in trace element analysis by X-ray emission spectroscopy

International Nuclear Information System (INIS)

Valkovic, V.

1983-11-01

The report, written under a research contract with the IAEA, contains a detailed presentation of the most difficult problem encountered in the trace element analysis by methods of the X-ray emission spectroscopy, namely the sample preparation techniques. The following items are covered. Sampling - with specific consideration of aerosols, water, soil, biological materials, petroleum and its products, storage of samples and their handling. Pretreatment of samples - preconcentration, ashing, solvent extraction, ion exchange and electrodeposition. Sample preparations for PIXE - analysis - backings, target uniformity and homogeneity, effects of irradiation, internal standards and specific examples of preparation (aqueous, biological, blood serum and solid samples). Sample preparations for radioactive sources or tube excitation - with specific examples (water, liquid and solid samples, soil, geological, plants and tissue samples). Finally, the problem of standards and reference materials, as well as that of interlaboratory comparisons, is discussed

Quantitating morphological changes in biological samples during scanning electron microscopy sample preparation with correlative super-resolution microscopy.

Science.gov (United States)

Zhang, Ying; Huang, Tao; Jorgens, Danielle M; Nickerson, Andrew; Lin, Li-Jung; Pelz, Joshua; Gray, Joe W; López, Claudia S; Nan, Xiaolin

2017-01-01

Sample preparation is critical to biological electron microscopy (EM), and there have been continuous efforts on optimizing the procedures to best preserve structures of interest in the sample. However, a quantitative characterization of the morphological changes associated with each step in EM sample preparation is currently lacking. Using correlative EM and superresolution microscopy (SRM), we have examined the effects of different drying methods as well as osmium tetroxide (OsO4) post-fixation on cell morphology during scanning electron microscopy (SEM) sample preparation. Here, SRM images of the sample acquired under hydrated conditions were used as a baseline for evaluating morphological changes as the sample went through SEM sample processing. We found that both chemical drying and critical point drying lead to a mild cellular boundary retraction of ~60 nm. Post-fixation by OsO4 causes at least 40 nm additional boundary retraction. We also found that coating coverslips with adhesion molecules such as fibronectin prior to cell plating helps reduce cell distortion from OsO4 post-fixation. These quantitative measurements offer useful information for identifying causes of cell distortions in SEM sample preparation and improving current procedures.

Sample Preparation for Mass Spectrometry Imaging of Plant Tissues: A Review

Science.gov (United States)

Dong, Yonghui; Li, Bin; Malitsky, Sergey; Rogachev, Ilana; Aharoni, Asaph; Kaftan, Filip; Svatoš, Aleš; Franceschi, Pietro

2016-01-01

Mass spectrometry imaging (MSI) is a mass spectrometry based molecular ion imaging technique. It provides the means for ascertaining the spatial distribution of a large variety of analytes directly on tissue sample surfaces without any labeling or staining agents. These advantages make it an attractive molecular histology tool in medical, pharmaceutical, and biological research. Likewise, MSI has started gaining popularity in plant sciences; yet, information regarding sample preparation methods for plant tissues is still limited. Sample preparation is a crucial step that is directly associated with the quality and authenticity of the imaging results, it therefore demands in-depth studies based on the characteristics of plant samples. In this review, a sample preparation pipeline is discussed in detail and illustrated through selected practical examples. In particular, special concerns regarding sample preparation for plant imaging are critically evaluated. Finally, the applications of MSI techniques in plants are reviewed according to different classes of plant metabolites. PMID:26904042

Sample Preparation for Mass Spectrometry Imaging of Plant Tissues: A Review.

Science.gov (United States)

Dong, Yonghui; Li, Bin; Malitsky, Sergey; Rogachev, Ilana; Aharoni, Asaph; Kaftan, Filip; Svatoš, Aleš; Franceschi, Pietro

2016-01-01

Mass spectrometry imaging (MSI) is a mass spectrometry based molecular ion imaging technique. It provides the means for ascertaining the spatial distribution of a large variety of analytes directly on tissue sample surfaces without any labeling or staining agents. These advantages make it an attractive molecular histology tool in medical, pharmaceutical, and biological research. Likewise, MSI has started gaining popularity in plant sciences; yet, information regarding sample preparation methods for plant tissues is still limited. Sample preparation is a crucial step that is directly associated with the quality and authenticity of the imaging results, it therefore demands in-depth studies based on the characteristics of plant samples. In this review, a sample preparation pipeline is discussed in detail and illustrated through selected practical examples. In particular, special concerns regarding sample preparation for plant imaging are critically evaluated. Finally, the applications of MSI techniques in plants are reviewed according to different classes of plant metabolites.

15N sample preparation for mass spectroscopy analysis

International Nuclear Information System (INIS)

Trivelin, P.C.O.; Salati, E.; Matsui, E.

1973-01-01

Technics for preparing 15 N samples to be analised is presented. Dumas method and oxidation by sodium hypobromite method are described in order to get the appropriate sample. Method to calculate 15 N ratio from mass spectrometry dates is also discussed [pt

Preparation of archaeological samples for its dating by thermoluminescence

International Nuclear Information System (INIS)

Mejia F, D.

2000-01-01

The present work shows the results of the preparation of archaeological samples for their dating by thermoluminescence (Tl) using the Fine grain technique established by Zimmerman but with the varying of such preparation was realized in normal daylight conditions, only the taking of the Tl readings were realized in dark room and red light. In the chapter 1 basic concepts are described about: matter constitution, radioactivity, units and radiation magnitudes, and thermoluminescence. In the chapter 2 some theoretical aspects on dating are showed. It is described how realizing the samples collection, the fine grain method, the determination of the accumulated dose through the years or paleodoses (P=Q+I) by mean of the increasing to obtain the dose equivalent dose (Q) and the signal regeneration method to obtain the correction factor by supra linearity (1), the determination of the annual dose rate to apply the age equation and the evaluation of the age uncertainty with the error limits. The development of experimental part with samples from the archaeological site named Edzna in Campeche, Mexico is described in the chapter 3. The results are presented in the chapter 4. It was obtained an age for the sample named CH7 it was obtained an age of 389 ± years. In conclusion the preparation of the archaeological samples for their dating by Tl in the conditions before mentioned is reliable, but they must be realized more studies with samples of well known age, preparing them in normal daylight conditions and simultaneously in dark room with red light. In order to observe how respond the minerals present in the sample at different dose rapidity, the same samples must be radiated with radiation sources with different dose rate. (Author)

Sample preparation and EFTEM of Meat Samples for Nanoparticle Analysis in Food

International Nuclear Information System (INIS)

Lari, L; Dudkiewicz, A

2014-01-01

Nanoparticles are used in industry for personal care products and the preparation of food. In the latter application, their functions include the prevention of microbes' growth, increase of the foods nutritional value and sensory quality. EU regulations require a risk assessment of the nanoparticles used in foods and food contact materials before the products can reach the market. However, availability of validated analytical methodologies for detection and characterisation of the nanoparticles in food hampers appropriate risk assessment. As part of a research on the evaluation of the methods for screening and quantification of Ag nanoparticles in meat we have tested a new TEM sample preparation alternative to resin embedding and cryo-sectioning. Energy filtered TEM analysis was applied to evaluate thickness and the uniformity of thin meat layers acquired at increasing input of the sample demonstrating that the protocols used ensured good stability under the electron beam, reliable sample concentration and reproducibility

Sample preparation and EFTEM of Meat Samples for Nanoparticle Analysis in Food

Science.gov (United States)

Lari, L.; Dudkiewicz, A.

2014-06-01

Nanoparticles are used in industry for personal care products and the preparation of food. In the latter application, their functions include the prevention of microbes' growth, increase of the foods nutritional value and sensory quality. EU regulations require a risk assessment of the nanoparticles used in foods and food contact materials before the products can reach the market. However, availability of validated analytical methodologies for detection and characterisation of the nanoparticles in food hampers appropriate risk assessment. As part of a research on the evaluation of the methods for screening and quantification of Ag nanoparticles in meat we have tested a new TEM sample preparation alternative to resin embedding and cryo-sectioning. Energy filtered TEM analysis was applied to evaluate thickness and the uniformity of thin meat layers acquired at increasing input of the sample demonstrating that the protocols used ensured good stability under the electron beam, reliable sample concentration and reproducibility.

Final LDRD report : development of sample preparation methods for ChIPMA-based imaging mass spectrometry of tissue samples.

Energy Technology Data Exchange (ETDEWEB)

Maharrey, Sean P.; Highley, Aaron M.; Behrens, Richard, Jr.; Wiese-Smith, Deneille

2007-12-01

The objective of this short-term LDRD project was to acquire the tools needed to use our chemical imaging precision mass analyzer (ChIPMA) instrument to analyze tissue samples. This effort was an outgrowth of discussions with oncologists on the need to find the cellular origin of signals in mass spectra of serum samples, which provide biomarkers for ovarian cancer. The ultimate goal would be to collect chemical images of biopsy samples allowing the chemical images of diseased and nondiseased sections of a sample to be compared. The equipment needed to prepare tissue samples have been acquired and built. This equipment includes an cyro-ultramicrotome for preparing thin sections of samples and a coating unit. The coating unit uses an electrospray system to deposit small droplets of a UV-photo absorbing compound on the surface of the tissue samples. Both units are operational. The tissue sample must be coated with the organic compound to enable matrix assisted laser desorption/ionization (MALDI) and matrix enhanced secondary ion mass spectrometry (ME-SIMS) measurements with the ChIPMA instrument Initial plans to test the sample preparation using human tissue samples required development of administrative procedures beyond the scope of this LDRD. Hence, it was decided to make two types of measurements: (1) Testing the spatial resolution of ME-SIMS by preparing a substrate coated with a mixture of an organic matrix and a bio standard and etching a defined pattern in the coating using a liquid metal ion beam, and (2) preparing and imaging C. elegans worms. Difficulties arose in sectioning the C. elegans for analysis and funds and time to overcome these difficulties were not available in this project. The facilities are now available for preparing biological samples for analysis with the ChIPMA instrument. Some further investment of time and resources in sample preparation should make this a useful tool for chemical imaging applications.

Method for developing cost estimates for generic regulatory requirements

International Nuclear Information System (INIS)

1985-01-01

The NRC has established a practice of performing regulatory analyses, reflecting costs as well as benefits, of proposed new or revised generic requirements. A method had been developed to assist the NRC in preparing the types of cost estimates required for this purpose and for assigning priorities in the resolution of generic safety issues. The cost of a generic requirement is defined as the net present value of total lifetime cost incurred by the public, industry, and government in implementing the requirement for all affected plants. The method described here is for commercial light-water-reactor power plants. Estimating the cost for a generic requirement involves several steps: (1) identifying the activities that must be carried out to fully implement the requirement, (2) defining the work packages associated with the major activities, (3) identifying the individual elements of cost for each work package, (4) estimating the magnitude of each cost element, (5) aggregating individual plant costs over the plant lifetime, and (6) aggregating all plant costs and generic costs to produce a total, national, present value of lifetime cost for the requirement. The method developed addresses all six steps. In this paper, we discuss on the first three

Randomized, double blind comparison of brand and generic antibiotic suspensions: II. A study of taste and compliance in children.

Science.gov (United States)

El-Chaar, G M; Mardy, G; Wehlou, K; Rubin, L G

1996-01-01

The taste of oral liquid medications influences compliance in children. Generic preparations are prescribed to reduce cost and may taste worse than brand name products. This was a prospective, randomized, double blind, crossover trial of the differences in taste and compliance between brand and generic antibiotic suspensions in children 3 to 14 years of age. Verbal and visual assessment methods were used to assess taste, and compliance was measured by the amount of drug returned after use. Ten children in each of the cephalexin and erythromycin-sulfisoxazole groups did not report that the brand and generic formulations tasted differently. Fifteen children thought that brand trimethoprim-sulfamethoxazole tasted better than the generic preparation. Brand name oral liquid antibiotics do not necessarily taste better than their generic counterparts. Despite preference for the taste of brand trimethoprim-sulfamethoxazole, all of the children in this study were compliant with both brand and generic medications.

Sample preparation composite and replicate strategy for assay of solid oral drug products.

Science.gov (United States)

Harrington, Brent; Nickerson, Beverly; Guo, Michele Xuemei; Barber, Marc; Giamalva, David; Lee, Carlos; Scrivens, Garry

2014-12-16

In pharmaceutical analysis, the results of drug product assay testing are used to make decisions regarding the quality, efficacy, and stability of the drug product. In order to make sound risk-based decisions concerning drug product potency, an understanding of the uncertainty of the reportable assay value is required. Utilizing the most restrictive criteria in current regulatory documentation, a maximum variability attributed to method repeatability is defined for a drug product potency assay. A sampling strategy that reduces the repeatability component of the assay variability below this predefined maximum is demonstrated. The sampling strategy consists of determining the number of dosage units (k) to be prepared in a composite sample of which there may be a number of equivalent replicate (r) sample preparations. The variability, as measured by the standard error (SE), of a potency assay consists of several sources such as sample preparation and dosage unit variability. A sampling scheme that increases the number of sample preparations (r) and/or number of dosage units (k) per sample preparation will reduce the assay variability and thus decrease the uncertainty around decisions made concerning the potency of the drug product. A maximum allowable repeatability component of the standard error (SE) for the potency assay is derived using material in current regulatory documents. A table of solutions for the number of dosage units per sample preparation (r) and number of replicate sample preparations (k) is presented for any ratio of sample preparation and dosage unit variability.

Use of robotic systems for radiochemical sample changing and for analytical sample preparation

International Nuclear Information System (INIS)

Delmastro, J.R.; Hartenstein, S.D.; Wade, M.A.

1989-01-01

Two uses of the Perkin-Elmer (PE) robotic system will be presented. In the first, a PE robot functions as an automatic sample changer for up to five low energy photon spectrometry (LEPS) detectors operated with a Nuclear Data ND 6700 system. The entire system, including the robot, is controlled by an IBM PC-AT using software written in compiled BASIC. Problems associated with the development of the system and modifications to the robot will be presented. In the second, an evaluation study was performed to assess the abilities of the PE robotic system for performing complex analytical sample preparation procedures. For this study, a robotic system based upon the PE robot and auxiliary devices was constructed and programmed to perform the preparation of final product samples (UO 3 ) for accountability and impurity specification analyses. These procedures require sample dissolution, dilution, and liquid-liquid extraction steps. The results of an in-depth evaluation of all system components will be presented

Sample preparation of energy materials for X-ray nanotomography with micromanipulation.

Science.gov (United States)

Chen-Wiegart, Yu-chen Karen; Camino, Fernando E; Wang, Jun

2014-06-06

X-ray nanotomography presents an unprecedented opportunity to study energy storage/conversion materials at nanometer scales in three dimensions, with both elemental and chemical sensitivity. A critical step in obtaining high-quality X-ray nanotomography data is reliable sample preparation to ensure that the entire sample fits within the field of view of the X-ray microscope. Although focused-ion-beam lift-out has previously been used for large sample (few to tens of microns) preparation, a difficult undercut and lift-out procedure results in a time-consuming sample preparation process. Herein, we propose a much simpler and direct sample preparation method to resolve the issues that block the view of the sample base after milling and during the lift-out process. This method is applied on a solid-oxide fuel cell and a lithium-ion battery electrode, before numerous critical 3D morphological parameters are extracted, which are highly relevant to their electrochemical performance. A broad application of this method for microstructure study with X-ray nanotomography is discussed and presented. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sample preparation optimization in fecal metabolic profiling.

Science.gov (United States)

Deda, Olga; Chatziioannou, Anastasia Chrysovalantou; Fasoula, Stella; Palachanis, Dimitris; Raikos, Νicolaos; Theodoridis, Georgios A; Gika, Helen G

2017-03-15

Metabolomic analysis of feces can provide useful insight on the metabolic status, the health/disease state of the human/animal and the symbiosis with the gut microbiome. As a result, recently there is increased interest on the application of holistic analysis of feces for biomarker discovery. For metabolomics applications, the sample preparation process used prior to the analysis of fecal samples is of high importance, as it greatly affects the obtained metabolic profile, especially since feces, as matrix are diversifying in their physicochemical characteristics and molecular content. However there is still little information in the literature and lack of a universal approach on sample treatment for fecal metabolic profiling. The scope of the present work was to study the conditions for sample preparation of rat feces with the ultimate goal of the acquisition of comprehensive metabolic profiles either untargeted by NMR spectroscopy and GC-MS or targeted by HILIC-MS/MS. A fecal sample pooled from male and female Wistar rats was extracted under various conditions by modifying the pH value, the nature of the organic solvent and the sample weight to solvent volume ratio. It was found that the 1/2 (w f /v s ) ratio provided the highest number of metabolites under neutral and basic conditions in both untargeted profiling techniques. Concerning LC-MS profiles, neutral acetonitrile and propanol provided higher signals and wide metabolite coverage, though extraction efficiency is metabolite dependent. Copyright © 2016 Elsevier B.V. All rights reserved.

Comparison of sample preparation procedures on metal(loid) fractionation patterns in lichens.

Science.gov (United States)

Kroukamp, E M; Godeto, T W; Forbes, P B C

2017-08-13

The effects of different sample preparation strategies and storage on metal(loid) fractionation trends in plant material is largely underresearched. In this study, a bulk sample of lichen Parmotrema austrosinense (Zahlbr.) Hale was analysed for its total extractable metal(loid) content by ICP-MS, and was determined to be adequately homogenous (sample were prepared utilising a range of sample preservation techniques and subjected to a modified sequential extraction procedure or to total metal extraction. Both experiments were repeated after 1-month storage at 4 °C. Cryogenic freezing gave the best reproducibility for total extractable elemental concentrations between months, indicating this to be the most suitable method of sample preparation in such studies. The combined extraction efficiencies were >82% for As, Cu, Mn, Pb, Sr and Zn but poor for other elements, where sample preparation strategies 'no sample preparation' and 'dried in a desiccator' had the best extraction recoveries. Cryogenic freezing procedures had a significantly (p sample cleaning and preservation when species fractionation patterns are of interest. This study also shows that the assumption that species stability can be ensured through cryopreservation and freeze drying techniques needs to be revisited.

Field Sample Preparation Method Development for Isotope Ratio Mass Spectrometry

International Nuclear Information System (INIS)

Leibman, C.; Weisbrod, K.; Yoshida, T.

2015-01-01

Non-proliferation and International Security (NA-241) established a working group of researchers from Los Alamos National Laboratory (LANL), Pacific Northwest National Laboratory (PNNL) and Savannah River National Laboratory (SRNL) to evaluate the utilization of in-field mass spectrometry for safeguards applications. The survey of commercial off-the-shelf (COTS) mass spectrometers (MS) revealed no instrumentation existed capable of meeting all the potential safeguards requirements for performance, portability, and ease of use. Additionally, fieldable instruments are unlikely to meet the International Target Values (ITVs) for accuracy and precision for isotope ratio measurements achieved with laboratory methods. The major gaps identified for in-field actinide isotope ratio analysis were in the areas of: 1. sample preparation and/or sample introduction, 2. size reduction of mass analyzers and ionization sources, 3. system automation, and 4. decreased system cost. Development work in 2 through 4, numerated above continues, in the private and public sector. LANL is focusing on developing sample preparation/sample introduction methods for use with the different sample types anticipated for safeguard applications. Addressing sample handling and sample preparation methods for MS analysis will enable use of new MS instrumentation as it becomes commercially available. As one example, we have developed a rapid, sample preparation method for dissolution of uranium and plutonium oxides using ammonium bifluoride (ABF). ABF is a significantly safer and faster alternative to digestion with boiling combinations of highly concentrated mineral acids. Actinides digested with ABF yield fluorides, which can then be analyzed directly or chemically converted and separated using established column chromatography techniques as needed prior to isotope analysis. The reagent volumes and the sample processing steps associated with ABF sample digestion lend themselves to automation and field

Choice and preparation of standard samples for X-ray spectral microanalysis

International Nuclear Information System (INIS)

Gavrilenko, I.S.; Surzhko, V.F.

1989-01-01

Choice, preparation and certification of standard samples for X-ray spectral microanalysis are considered. Requirements for standard samples in terms of concentration and volume, porosity, corrosion, conductivity distribution are formulated. Stages of sample preparation process, including composition choice, heat treatment, section production, certification, are considered in detail. The choice of composition is based on studying phase equilibrium diagrams, subdivided into 6 types

Novel strategies for sample preparation in forensic toxicology.

Science.gov (United States)

Samanidou, Victoria; Kovatsi, Leda; Fragou, Domniki; Rentifis, Konstantinos

2011-09-01

This paper provides a review of novel strategies for sample preparation in forensic toxicology. The review initially outlines the principle of each technique, followed by sections addressing each class of abused drugs separately. The novel strategies currently reviewed focus on the preparation of various biological samples for the subsequent determination of opiates, benzodiazepines, amphetamines, cocaine, hallucinogens, tricyclic antidepressants, antipsychotics and cannabinoids. According to our experience, these analytes are the most frequently responsible for intoxications in Greece. The applications of techniques such as disposable pipette extraction, microextraction by packed sorbent, matrix solid-phase dispersion, solid-phase microextraction, polymer monolith microextraction, stir bar sorptive extraction and others, which are rapidly gaining acceptance in the field of toxicology, are currently reviewed.

76 FR 24920 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-05-03

... precision requirements or power calculations that justify the proposed sample size, the expected response... Collection; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service... Information Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback...

76 FR 35069 - Agency Information Collection Activities; Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-06-15

... precision requirements or power calculations that justify the proposed sample size, the expected response...; Proposed Collection; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on... (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery...

78 FR 74175 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2013-12-10

... precision requirements or power calculations that justify the proposed sample size, the expected response...: Proposed Collection; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on... Information Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback...

77 FR 52708 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2012-08-30

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential...: Proposed Collection; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on... Information Collection request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback...

TEM sample preparation by FIB for carbon nanotube interconnects

International Nuclear Information System (INIS)

Ke, Xiaoxing; Bals, Sara; Romo Negreira, Ainhoa; Hantschel, Thomas; Bender, Hugo; Van Tendeloo, Gustaaf

2009-01-01

A powerful method to study carbon nanotubes (CNTs) grown in patterned substrates for potential interconnects applications is transmission electron microscopy (TEM). However, high-quality TEM samples are necessary for such a study. Here, TEM specimen preparation by focused ion beam (FIB) has been used to obtain lamellae of patterned samples containing CNTs grown inside contact holes. A dual-cap Pt protection layer and an extensive 5 kV cleaning procedure are applied in order to preserve the CNTs and avoid deterioration during milling. TEM results show that the inner shell structure of the carbon nanotubes has been preserved, which proves that focused ion beam is a useful technique to prepare TEM samples of CNT interconnects.

TEM sample preparation by FIB for carbon nanotube interconnects

Energy Technology Data Exchange (ETDEWEB)

Ke, Xiaoxing, E-mail: xiaoxing.ke@ua.ac.be [EMAT, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Bals, Sara [EMAT, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Romo Negreira, Ainhoa [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Metallurgy and Materials Engineering Department, KU Leuven, Kasteelpark Arenberg 44, Leuven B-3001 (Belgium); Hantschel, Thomas; Bender, Hugo [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Van Tendeloo, Gustaaf [EMAT, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium)

2009-10-15

A powerful method to study carbon nanotubes (CNTs) grown in patterned substrates for potential interconnects applications is transmission electron microscopy (TEM). However, high-quality TEM samples are necessary for such a study. Here, TEM specimen preparation by focused ion beam (FIB) has been used to obtain lamellae of patterned samples containing CNTs grown inside contact holes. A dual-cap Pt protection layer and an extensive 5 kV cleaning procedure are applied in order to preserve the CNTs and avoid deterioration during milling. TEM results show that the inner shell structure of the carbon nanotubes has been preserved, which proves that focused ion beam is a useful technique to prepare TEM samples of CNT interconnects.

Supporting Sampling and Sample Preparation Tools for Isotope and Nuclear Analysis

International Nuclear Information System (INIS)

2016-03-01

Nuclear and related techniques can help develop climate-smart agricultural practices by optimizing water and nutrient use efficiency, assessing organic carbon sequestration in soil, and assisting in the evaluation of soil erosion control measures. Knowledge on the behaviour of radioactive materials in soil, water and foodstuffs is also essential in enhancing nuclear emergency preparedness and response. Appropriate sampling and sample preparation are the first steps to ensure the quality and effective use of the measurements and this publication provides comprehensive detail on the necessary steps

Selecting Sample Preparation Workflows for Mass Spectrometry-Based Proteomic and Phosphoproteomic Analysis of Patient Samples with Acute Myeloid Leukemia.

Science.gov (United States)

Hernandez-Valladares, Maria; Aasebø, Elise; Selheim, Frode; Berven, Frode S; Bruserud, Øystein

2016-08-22

Global mass spectrometry (MS)-based proteomic and phosphoproteomic studies of acute myeloid leukemia (AML) biomarkers represent a powerful strategy to identify and confirm proteins and their phosphorylated modifications that could be applied in diagnosis and prognosis, as a support for individual treatment regimens and selection of patients for bone marrow transplant. MS-based studies require optimal and reproducible workflows that allow a satisfactory coverage of the proteome and its modifications. Preparation of samples for global MS analysis is a crucial step and it usually requires method testing, tuning and optimization. Different proteomic workflows that have been used to prepare AML patient samples for global MS analysis usually include a standard protein in-solution digestion procedure with a urea-based lysis buffer. The enrichment of phosphopeptides from AML patient samples has previously been carried out either with immobilized metal affinity chromatography (IMAC) or metal oxide affinity chromatography (MOAC). We have recently tested several methods of sample preparation for MS analysis of the AML proteome and phosphoproteome and introduced filter-aided sample preparation (FASP) as a superior methodology for the sensitive and reproducible generation of peptides from patient samples. FASP-prepared peptides can be further fractionated or IMAC-enriched for proteome or phosphoproteome analyses. Herein, we will review both in-solution and FASP-based sample preparation workflows and encourage the use of the latter for the highest protein and phosphorylation coverage and reproducibility.

Development of sample preparation method for honey analysis using PIXE

International Nuclear Information System (INIS)

Saitoh, Katsumi; Chiba, Keiko; Sera, Koichiro

2008-01-01

We developed an original preparation method for honey samples (samples in paste-like state) specifically designed for PIXE analysis. The results of PIXE analysis of thin targets prepared by adding a standard containing nine elements to honey samples demonstrated that the preparation method bestowed sufficient accuracy on quantitative values. PIXE analysis of 13 kinds of honey was performed, and eight mineral components (Si, P, S, K, Ca, Mn, Cu and Zn) were detected in all honey samples. The principal mineral components were K and Ca, and the quantitative value for K accounted for the majority of the total value for mineral components. K content in honey varies greatly depending on the plant source. Chestnuts had the highest K content. In fact, it was 2-3 times that of Manuka, which is known as a high quality honey. K content of false-acacia, which is produced in the greatest abundance, was 1/20 that of chestnuts. (author)

Witness sample preparation for measuring antireflection coatings.

Science.gov (United States)

Willey, Ronald R

2014-02-01

Measurement of antireflection coating of witness samples from across the worldwide industry has been shown to have excess variability from a sampling taken for the OSA Topical Meeting on Optical Interference Coatings: Measurement Problem. Various sample preparation techniques have been discussed with their limitations, and a preferred technique is recommended with its justification, calibration procedures, and limitations. The common practice of grinding the second side to reduce its reflection is less than satisfactory. One recommended practice is to paint the polished second side, which reduces its reflection to almost zero. A method to evaluate the suitability of given paints is also described.

Sample preparation method for scanning force microscopy

CERN Document Server

Jankov, I R; Szente, R N; Carreno, M N P; Swart, J W; Landers, R

2001-01-01

We present a method of sample preparation for studies of ion implantation on metal surfaces. The method, employing a mechanical mask, is specially adapted for samples analysed by Scanning Force Microscopy. It was successfully tested on polycrystalline copper substrates implanted with phosphorus ions at an acceleration voltage of 39 keV. The changes of the electrical properties of the surface were measured by Kelvin Probe Force Microscopy and the surface composition was analysed by Auger Electron Spectroscopy.

77 FR 17493 - Agency Information Collection Activities: Proposed Collection; Comment Request; DOI Generic...

Science.gov (United States)

2012-03-26

... justify the proposed sample size, the expected response rate, methods for assessing potential non...: Proposed Collection; Comment Request; DOI Generic Clearance for the Collection of Qualitative Feedback on... (Generic ICR): ``DOI Generic Clearance for the Collection of Qualitative Feedback on Agency Service...

75 FR 80542 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2010-12-22

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential...; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery... Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency...

76 FR 12140 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-03-04

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential...; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery... Information Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback...

76 FR 19826 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-04-08

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential... Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery AGENCY... (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery...

76 FR 17861 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-03-31

... requirements or power calculations that justify the proposed sample size, the expected response rate, methods...; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery... Information Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback...

76 FR 25693 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-05-05

... requirements or power calculations that justify the proposed sample size, the expected response rate, methods... Collection; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service... Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency...

Status report of AMS sample preparation laboratory at GADAM Centre, Gliwice, Poland

Energy Technology Data Exchange (ETDEWEB)

Piotrowska, N., E-mail: natalia.piotrowska@polsl.pl [GADAM Centre of Excellence, Department of Radioisotopes, Institute of Physics, Silesian University of Technology, Gliwice (Poland)

2013-01-15

The laboratory for {sup 14}C AMS sample preparation in the Gliwice Radiocarbon Laboratory has gradually evolved since its start in 1999 to cater for an increase in volume and variety of radiocarbon dating samples. To date, nearly 2000 graphite targets have been produced from materials such as plant macrofossils, charcoal, peat, bones, shells and wood. The equipment comprises a station for chemical preparation and high vacuum lines for production, purification and graphitization of sample carbon dioxide. The present capacity allows preparation of up to 400 targets annually for the needs of scientific projects and external orders for radiocarbon dating continuously received by the GADAM Centre of Excellence. The laboratory's sample preparation protocols and recent improvements are described and its performance during the 10 years of activity is discussed in terms of parameters obtained from reference materials prepared in this laboratory and demonstrated with a few science applications.

Sample preparation techniques of biological material for isotope analysis

International Nuclear Information System (INIS)

Axmann, H.; Sebastianelli, A.; Arrillaga, J.L.

1990-01-01

Sample preparation is an essential step in all isotope-aided experiments but often it is not given enough attention. The methods of sample preparation are very important to obtain reliable and precise analytical data and for further interpretation of results. The size of a sample required for chemical analysis is usually very small (10mg-1500mg). On the other hand the amount of harvested plant material from plots in a field experiment is often bulky (several kilograms) and the entire sample is too large for processing. In addition, while approaching maturity many crops show not only differences in physical consistency but also a non-uniformity in 15 N content among plant parts, requiring a plant fractionation or separation into parts (vegetative and reproductive) e.g. shoots and spikes, in case of small grain cereals, shoots and pods in case of grain legumes and tops and roots or beets (including crown) in case of sugar beet, etc. In any case the ultimate goal of these procedures is to obtain representative subsample harvested from greenhouse or field experiments for chemical analysis. Before harvesting an isotopic-aided experiment the method of sampling has to be selected. It should be based on the type of information required in relation to the objectives of the research and the availability of resources (staff, sample preparation equipment, analytical facilities, chemicals and supplies, etc.). 10 refs, 3 figs, 3 tabs

[Progress in sample preparation and analytical methods for trace polar small molecules in complex samples].

Science.gov (United States)

Zhang, Qianchun; Luo, Xialin; Li, Gongke; Xiao, Xiaohua

2015-09-01

Small polar molecules such as nucleosides, amines, amino acids are important analytes in biological, food, environmental, and other fields. It is necessary to develop efficient sample preparation and sensitive analytical methods for rapid analysis of these polar small molecules in complex matrices. Some typical materials in sample preparation, including silica, polymer, carbon, boric acid and so on, are introduced in this paper. Meanwhile, the applications and developments of analytical methods of polar small molecules, such as reversed-phase liquid chromatography, hydrophilic interaction chromatography, etc., are also reviewed.

Considerations for Sample Preparation Using Size-Exclusion Chromatography for Home and Synchrotron Sources.

Science.gov (United States)

Rambo, Robert P

2017-01-01

The success of a SAXS experiment for structural investigations depends on two precise measurements, the sample and the buffer background. Buffer matching between the sample and background can be achieved using dialysis methods but in biological SAXS of monodisperse systems, sample preparation is routinely being performed with size exclusion chromatography (SEC). SEC is the most reliable method for SAXS sample preparation as the method not only purifies the sample for SAXS but also almost guarantees ideal buffer matching. Here, I will highlight the use of SEC for SAXS sample preparation and demonstrate using example proteins that SEC purification does not always provide for ideal samples. Scrutiny of the SEC elution peak using quasi-elastic and multi-angle light scattering techniques can reveal hidden features (heterogeneity) of the sample that should be considered during SAXS data analysis. In some cases, sample heterogeneity can be controlled using a small molecule additive and I outline a simple additive screening method for sample preparation.

A Method for Microalgae Proteomics Analysis Based on Modified Filter-Aided Sample Preparation.

Science.gov (United States)

Li, Song; Cao, Xupeng; Wang, Yan; Zhu, Zhen; Zhang, Haowei; Xue, Song; Tian, Jing

2017-11-01

With the fast development of microalgal biofuel researches, the proteomics studies of microalgae increased quickly. A filter-aided sample preparation (FASP) method is widely used proteomics sample preparation method since 2009. Here, a method of microalgae proteomics analysis based on modified filter-aided sample preparation (mFASP) was described to meet the characteristics of microalgae cells and eliminate the error caused by over-alkylation. Using Chlamydomonas reinhardtii as the model, the prepared sample was tested by standard LC-MS/MS and compared with the previous reports. The results showed mFASP is suitable for most of occasions of microalgae proteomics studies.

Selecting Sample Preparation Workflows for Mass Spectrometry-Based Proteomic and Phosphoproteomic Analysis of Patient Samples with Acute Myeloid Leukemia

Directory of Open Access Journals (Sweden)

Maria Hernandez-Valladares

2016-08-01

Full Text Available Global mass spectrometry (MS-based proteomic and phosphoproteomic studies of acute myeloid leukemia (AML biomarkers represent a powerful strategy to identify and confirm proteins and their phosphorylated modifications that could be applied in diagnosis and prognosis, as a support for individual treatment regimens and selection of patients for bone marrow transplant. MS-based studies require optimal and reproducible workflows that allow a satisfactory coverage of the proteome and its modifications. Preparation of samples for global MS analysis is a crucial step and it usually requires method testing, tuning and optimization. Different proteomic workflows that have been used to prepare AML patient samples for global MS analysis usually include a standard protein in-solution digestion procedure with a urea-based lysis buffer. The enrichment of phosphopeptides from AML patient samples has previously been carried out either with immobilized metal affinity chromatography (IMAC or metal oxide affinity chromatography (MOAC. We have recently tested several methods of sample preparation for MS analysis of the AML proteome and phosphoproteome and introduced filter-aided sample preparation (FASP as a superior methodology for the sensitive and reproducible generation of peptides from patient samples. FASP-prepared peptides can be further fractionated or IMAC-enriched for proteome or phosphoproteome analyses. Herein, we will review both in-solution and FASP-based sample preparation workflows and encourage the use of the latter for the highest protein and phosphorylation coverage and reproducibility.

Final Report for X-ray Diffraction Sample Preparation Method Development

Energy Technology Data Exchange (ETDEWEB)

Ely, T. M. [Hanford Site (HNF), Richland, WA (United States); Meznarich, H. K. [Hanford Site (HNF), Richland, WA (United States); Valero, T. [Hanford Site (HNF), Richland, WA (United States)

2018-01-30

WRPS-1500790, “X-ray Diffraction Saltcake Sample Preparation Method Development Plan/Procedure,” was originally prepared with the intent of improving the specimen preparation methodology used to generate saltcake specimens suitable for XRD-based solid phase characterization. At the time that this test plan document was originally developed, packed powder in cavity supports with collodion binder was the established XRD specimen preparation method. An alternate specimen preparation method less vulnerable, if not completely invulnerable to preferred orientation effects, was desired as a replacement for the method.

Protocol for Cohesionless Sample Preparation for Physical Experimentation

Science.gov (United States)

2016-05-01

Standard test method for consolidated drained triaxial compression test for soils . In Annual book of ASTM standards. West Conshohocken, PA: ASTM...derived wherein uncertainties and laboratory scatter associated with soil fabric-behavior variance during sample preparation are mitigated. Samples of...wherein comparable analysis between different laboratory tests’ results can be made by ensuring a comparable soil fabric prior to laboratory testing

Sample Preparation (SS): SE51_SS01 [Metabolonote[Archive

Lifescience Database Archive (English)

Full Text Available e Master NEO, BMS, Tokyo, Japan), and the seed powder was extracted with 1 mL of extraction buffer (0.1% HCO...trifugation (4 ℃, 10,000 rpm, 5 min), the sample tubes were subjected to sample preparation (buffer transfer

Challenges in TEM sample preparation of solvothermally grown CuInS2 films.

Science.gov (United States)

Frank, Anna; Changizi, Rasa; Scheu, Christina

2018-06-01

Transmission electron microscopy (TEM) is a widely used tool to characterize materials. The required samples need to be electron transparent which should be achieved without changing the microstructure. This work describes different TEM sample preparation techniques of nanostructured CuInS 2 thin films on fluorine-doped tin oxide substrates, synthesized solvothermally using l-cysteine as sulfur source. Focused ion beam lamellae, conventional cross section samples and scratch samples have been prepared and investigated. It was possible to prepare appropriate samples with each technique, however, each technique brings with it certain advantages and disadvantages. FIB preparation of solvothermally synthesized CuInS 2 suffers from two main drawbacks. First, the whole CuInS 2 layer displays a strongly increased Cu content caused by Cu migration and preferential removal of In. Further, electron diffraction shows the formation of an additional CuS phase after Ga + bombardment. Second, diffraction analysis is complicated by a strong contribution of crystalline Pt introduced during the FIB preparation and penetrating into the porous film surface. The conventional cross sectional CuInS 2 sample also shows a Cu signal enhancement which is caused by contribution of the brass tube material used for embedding. Additionally, Cu particles have been observed inside the CuInS 2 which have been sputtered on the film during preparation. Only the scratch samples allow an almost artefact-free and reliable elemental quantification using energy-dispersive X-ray spectroscopy. However, scratch samples suffer from the drawback that it is not possible to determine the layer thickness, which is possible for both cross sectional preparation techniques. Consequently, it is concluded that the type of sample preparation should be chosen dependent on the required information. A full characterization can only be achieved when the different techniques are combined. Copyright © 2018 Elsevier Ltd. All

Automated SEM and TEM sample preparation applied to copper/low k materials

Science.gov (United States)

Reyes, R.; Shaapur, F.; Griffiths, D.; Diebold, A. C.; Foran, B.; Raz, E.

2001-01-01

We describe the use of automated microcleaving for preparation of both SEM and TEM samples as done by SELA's new MC500 and TEMstation tools. The MC500 is an automated microcleaving tool that is capable of producing cleaves with 0.25 μm accuracy resulting in SEM-ready samples. The TEMstation is capable of taking a sample output from the MC500 (or from SELA's earlier MC200 tool) and producing a FIB ready slice of 25±5 μm, mounted on a TEM-washer and ready for FIB thinning to electron transparency for TEM analysis. The materials selected for the tool set evaluation mainly included the Cu/TaN/HOSP low-k system. The paper is divided into three sections, experimental approach, SEM preparation and analysis of HOSP low-k, and TEM preparation and analysis of Cu/TaN/HOSP low-k samples. For the samples discussed, data is presented to show the quality of preparation provided by these new automated tools.

Polymeric ionic liquid-based portable tip microextraction device for on-site sample preparation of water samples.

Science.gov (United States)

Chen, Lei; Pei, Junxian; Huang, Xiaojia; Lu, Min

2018-06-05

On-site sample preparation is highly desired because it avoids the transportation of large-volume samples and ensures the accuracy of the analytical results. In this work, a portable prototype of tip microextraction device (TMD) was designed and developed for on-site sample pretreatment. The assembly procedure of TMD is quite simple. Firstly, polymeric ionic liquid (PIL)-based adsorbent was in-situ prepared in a pipette tip. After that, the tip was connected with a syringe which was driven by a bidirectional motor. The flow rates in adsorption and desorption steps were controlled accurately by the motor. To evaluate the practicability of the developed device, the TMD was used to on-site sample preparation of waters and combined with high-performance liquid chromatography with diode array detection to measure trace estrogens in water samples. Under the most favorable conditions, the limits of detection (LODs, S/N = 3) for the target analytes were in the range of 4.9-22 ng/L, with good coefficients of determination. Confirmatory study well evidences that the extraction performance of TMD is comparable to that of the traditional laboratory solid-phase extraction process, but the proposed TMD is more simple and convenient. At the same time, the TMD avoids complicated sampling and transferring steps of large-volume water samples. Copyright © 2018 Elsevier B.V. All rights reserved.

Optimization of Sample Preparation processes of Bone Material for Raman Spectroscopy.

Science.gov (United States)

Chikhani, Madelen; Wuhrer, Richard; Green, Hayley

2018-03-30

Raman spectroscopy has recently been investigated for use in the calculation of postmortem interval from skeletal material. The fluorescence generated by samples, which affects the interpretation of Raman data, is a major limitation. This study compares the effectiveness of two sample preparation techniques, chemical bleaching and scraping, in the reduction of fluorescence from bone samples during testing with Raman spectroscopy. Visual assessment of Raman spectra obtained at 1064 nm excitation following the preparation protocols indicates an overall reduction in fluorescence. Results demonstrate that scraping is more effective at resolving fluorescence than chemical bleaching. The scraping of skeletonized remains prior to Raman analysis is a less destructive method and allows for the preservation of a bone sample in a state closest to its original form, which is beneficial in forensic investigations. It is recommended that bone scraping supersedes chemical bleaching as the preferred method for sample preparation prior to Raman spectroscopy. © 2018 American Academy of Forensic Sciences.

Magnetic separation techniques in sample preparation for biological analysis: a review.

Science.gov (United States)

He, Jincan; Huang, Meiying; Wang, Dongmei; Zhang, Zhuomin; Li, Gongke

2014-12-01

Sample preparation is a fundamental and essential step in almost all the analytical procedures, especially for the analysis of complex samples like biological and environmental samples. In past decades, with advantages of superparamagnetic property, good biocompatibility and high binding capacity, functionalized magnetic materials have been widely applied in various processes of sample preparation for biological analysis. In this paper, the recent advancements of magnetic separation techniques based on magnetic materials in the field of sample preparation for biological analysis were reviewed. The strategy of magnetic separation techniques was summarized. The synthesis, stabilization and bio-functionalization of magnetic nanoparticles were reviewed in detail. Characterization of magnetic materials was also summarized. Moreover, the applications of magnetic separation techniques for the enrichment of protein, nucleic acid, cell, bioactive compound and immobilization of enzyme were described. Finally, the existed problems and possible trends of magnetic separation techniques for biological analysis in the future were proposed. Copyright © 2014 Elsevier B.V. All rights reserved.

State of the art in sample preparation for trace element analysis (M1)

International Nuclear Information System (INIS)

Barnes, R.M.

2002-01-01

Full text: The accelerated capabilities of modern trace element analysis techniques, especially inductively coupled plasma mass spectrometry (ICP-MS), have challenged the sample preparation competence of most laboratories. Exceptional analytical sensitivity, remarkable analysis speed, automated sample presentation, and intelligent sample sequencing of modern spectroscopic instrumentation have lead to demanding requirements for appropriate sample preparation steps needed for ultra trace concentration and speciation measurements. Contamination control, reliable digestion and extraction techniques, presentation of chemical forms, sample matrix management, and intelligent sample processing available today are often inadequate for the most demanding measurements. Some commercial instrumentation provides convenient implementation of well-established contamination control measures, and reagent and container purity are steadily being improved. Direct sample introduction approaches offer alternatives to conventional solution samples, but achieving calibration reliability is difficult. Developing new sample preparation chemistry is especially arduous and rare, yet progress exists in characterizing microwave-assisted reactions. This presentation will describe contemporary targets for modern sample preparation approaches for ultra trace elemental analysis and the likelihood that they can be reasonably achieved. (author)

76 FR 21800 - Agency Information Collection Activities: Submission for OMB Review; Comment Request; Generic...

Science.gov (United States)

2011-04-18

... precision requirements or power calculations that justify the proposed sample size, the expected response... Activities: Submission for OMB Review; Comment Request; Generic Clearance for the Collection of Qualitative... Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency Service...

The effect of sample preparation methods on glass performance

International Nuclear Information System (INIS)

Oh, M.S.; Oversby, V.M.

1990-01-01

A series of experiments was conducted using SRL 165 synthetic waste glass to investigate the effects of surface preparation and leaching solution composition on the alteration of the glass. Samples of glass with as-cast surfaces produced smooth reaction layers and some evidence for precipitation of secondary phases from solution. Secondary phases were more abundant in samples reacted in deionized water than for those reacted in a silicate solution. Samples with saw-cut surfaces showed a large reduction in surface roughness after 7 days of reaction in either solution. Reaction in silicate solution for up to 91 days produced no further change in surface morphology, while reaction in DIW produced a spongy surface that formed the substrate for further surface layer development. The differences in the surface morphology of the samples may create microclimates that control the details of development of alteration layers on the glass; however, the concentrations of elements in leaching solutions show differences of 50% or less between samples prepared with different surface conditions for tests of a few months duration. 6 refs., 7 figs., 1 tab

Preparation of Cytology Samples: Tricks of the Trade.

Science.gov (United States)

Moore, A Russell

2017-01-01

General principles and techniques for collection, preparation, and staining of cytologic samples in the general practice setting are reviewed. Tips for collection of digital images are also discussed. Copyright © 2016 Elsevier Inc. All rights reserved.

Generic substitution of antiretrovirals: patients' and health care providers' opinions.

Science.gov (United States)

Kieran, Jennifer A; O'Reilly, Eimear; O'Dea, Siobhan; Bergin, Colm; O'Leary, Aisling

2017-10-01

There is interest in introducing generic antiretroviral drugs (ARVs) into high-income countries in order to maximise efficiency in health care budgets. Studies examining patients' and providers' knowledge and attitudes to generic substitution in HIV are few. This was a cross-sectional, observational study with a convenience sample of adult HIV-infected patients and health care providers (HCPs). Data on demographics, knowledge of generic medicine and facilitators of generic substitution were collected. Descriptive and univariate analysis was performed using SPSS V.23™. Questionnaires were completed by 66 patients. Seventy-one per cent would have no concerns with the introduction of generic ARVs. An increase in frequency of administration (61%) or pill burden (53%) would make patients less likely to accept generic ARVs. There were 30 respondents to the HCP survey. Concerns included the supply chain of generics, loss of fixed dose combinations, adherence and use of older medications. An increase in dosing frequency (76%) or an increase in pill burden (50%) would make HCPs less likely to prescribe a generic ARV. The main perceived advantage was financial. Generic substitution of ARVs would be acceptable to the majority of patients and HCPs. Reinvesting savings back into HIV services would facilitate the success of such a programme.

Sample preparation procedures utilized in microbial metabolomics: An overview.

Science.gov (United States)

Patejko, Małgorzata; Jacyna, Julia; Markuszewski, Michał J

2017-02-01

Bacteria are remarkably diverse in terms of their size, structure and biochemical properties. Due to this fact, it is hard to develop a universal method for handling bacteria cultures during metabolomic analysis. The choice of suitable processing methods constitutes a key element in any analysis, because only appropriate selection of procedures may provide accurate results, leading to reliable conclusions. Because of that, every analytical experiment concerning bacteria requires individually and very carefully planned research methodology. Although every study varies in terms of sample preparation, there are few general steps to follow while planning experiment, like sampling, separation of cells from growth medium, stopping their metabolism and extraction. As a result of extraction, all intracellular metabolites should be washed out from cell environment. What is more, extraction method utilized cannot cause any chemical decomposition or degradation of the metabolome. Furthermore, chosen extraction method should correlate with analytical technique, so it will not disturb or prolong following sample preparation steps. For those reasons, we observe a need to summarize sample preparation procedures currently utilized in microbial metabolomic studies. In the presented overview, papers concerning analysis of extra- and intracellular metabolites, published over the last decade, have been discussed. Presented work gives some basic guidelines that might be useful while planning experiments in microbial metabolomics. Copyright © 2016 Elsevier B.V. All rights reserved.

The generic article

NARCIS (Netherlands)

Farkas, D.F.; Swart, Henriëtte de

2005-01-01

We take a fresh look at the connection between genericity and (in)definiteness by reconsidering a long-standing puzzle concerning the relation between definiteness and genericity. We contrast English on the one hand and Romance languages and Hungarian on the other, focusing on generic sentences

Sample preparation techniques for (p, X) spectrometry

International Nuclear Information System (INIS)

Whitehead, N.E.

1985-01-01

Samples are ashed at low temperature, using oxygen plasma; a rotary evaporator, and freeze drying speeded up the ashing. The new design of apparatus manufactured was only 10 watt but was as efficient as a 200 watt commercial machine; a circuit diagram is included. Samples of hair and biopsy samples of skin were analysed by the technique. A wool standard was prepared for interlaboratory comparison exercises. It was based on New Zealand merino sheep wool and was 2.9 kg in weight. A washing protocol was developed, which preserves most of the trace element content. The wool was ground in liquid nitrogen using a plastic pestle and beaker, driven by a rotary drill press. (author)

Pharmaceutical quality of docetaxel generics versus originator drug product: a comparative analysis.

Science.gov (United States)

Vial, Jérôme; Cohen, Mélanie; Sassiat, Patrick; Thiébaut, Didier

2008-07-01

The aim of this study was to evaluate the quality of 31 commercially available generic formulations of docetaxel purchased in 14 countries by comparing their docetaxel content, impurity levels and pH versus those of the proprietary product Taxotere (Tx). Generic formulations were purchased in 14 countries in Asia, Africa, the Middle East and Latin America. Levels of docetaxel and impurities (chromatographic peaks above 0.05%) were obtained for each sample using reverse-phase liquid chromatography with ultraviolet detection. The pH of aqueous solutions of generic docetaxel formulations and Tx was also measured. A global evaluation of quality was conducted on each product using a multicriteria desirability analysis based on standards defined by the International Conference on Harmonisation guidelines and the US Pharmacopeia paclitaxel injection monograph. Most generic formulations contained a lower than expected amount of docetaxel and/or a high level of impurities: 21 generic docetaxel formulations had an average mass of docetaxel that was generic docetaxel formulations had a total impurity content of >3.0%, almost twice the level of impurities in Tx 20 mg. In total, 33 impurities not present in Tx were detected in the generic samples. Desirability analysis demonstrated that none of the generic docetaxel formulations had composition characteristics similar to those of Tx. This study demonstrated that from an analytical point of view, 90% of the generic docetaxel formulations evaluated contained insufficient active drug, high levels of impurities or both. This has the potential to affect both efficacy and safety of the drug.

Traceability and measurement uncertainty in sample preparation (W5)

International Nuclear Information System (INIS)

Wegscheider, W.; Walner, U.; Moser, J.

2002-01-01

Full text: Very few chemical measurements are being made directly on the object of interest and sample preparation is thus the rule rather than the exception in daily practice. Unfortunately the operations undertaken in the course of sample preparation are prone to rendering a sample useless for the purpose of interpreting a measurement performed on it, as it might not represent the original and relevant status any longer. Sample preparation along with sampling itself constitutes therefore a procedure that leads to a loss of representation of the original specimen or population. On the other hand it is also not sufficient to confine aspects of traceability and measurement uncertainty to the ultimate measurement, as the key purpose of measuring is to supply adequate data for some kind of decision, be it in production, in health, in the environment, or indeed in any other circumstance. These considerations have led to severe confusion in the community as to what traceability really means in chemistry. CITAC and EURACHEM have only recently issued a preliminary document that clarifies these issues and gives a firm handle on the future development of quality assurance in analytical chemistry. In this talk it will be attempted to outline the general ideas and procedures that lead to traceability of analytical chemical results accompanied by valid statements of their uncertainty. It will be argued that the central element in achieving these goals is a well-designed validation study that frequently goes beyond those requirements currently laid out in official documents. (author)

Mechanical Conversion for High-Throughput TEM Sample Preparation

International Nuclear Information System (INIS)

Kendrick, Anthony B; Moore, Thomas M; Zaykova-Feldman, Lyudmila

2006-01-01

This paper presents a novel method of direct mechanical conversion from lift-out sample to TEM sample holder. The lift-out sample is prepared in the FIB using the in-situ liftout Total Release TM method. The mechanical conversion is conducted using a mechanical press and one of a variety of TEM coupons, including coupons for both top-side and back-side thinning. The press joins a probe tip point with attached TEM sample to the sample coupon and separates the complete assembly as a 3mm diameter TEM grid, compatible with commercially available TEM sample holder rods. This mechanical conversion process lends itself well to the high through-put requirements of in-line process control and to materials characterization labs where instrument utilization and sample security are critically important

Smart Plasmonic Glucose Nanosensors as Generic Theranostic Agents for Targeting-Free Cancer Cell Screening and Killing.

Science.gov (United States)

Chen, Limei; Li, Haijuan; He, Haili; Wu, Haoxi; Jin, Yongdong

2015-07-07

Fast and accurate identification of cancer cells from healthy normal cells in a simple, generic way is very crucial for early cancer detection and treatment. Although functional nanoparticles, like fluorescent quantum dots and plasmonic Au nanoparticles (NPs), have been successfully applied for cancer cell imaging and photothermal therapy, they suffer from the main drawback of needing time-consuming targeting preparation for specific cancer cell detection and selective ablation. The lack of a generic and effective method therefore limits their potential high-throughput cancer cell preliminary screening and theranostic applications. We report herein a generic in vitro method for fast, targeting-free (avoiding time-consuming preparations of targeting moiety for specific cancer cells) visual screening and selective killing of cancer cells from normal cells, by using glucose-responsive/-sensitive glucose oxidase-modified Ag/Au nanoshells (Ag/Au-GOx NSs) as a smart plasmonic theranostic agent. The method is generic to some extent since it is based on the distinct localized surface plasmon resonance (LSPR) responses (and colors) of the smart nanoprobe with cancer cells (typically have a higher glucose uptake level) and normal cells.

40 CFR 205.171-2 - Test exhaust system sample selection and preparation.

Science.gov (United States)

2010-07-01

... Systems § 205.171-2 Test exhaust system sample selection and preparation. (a)(1) Exhaust systems... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Test exhaust system sample selection and preparation. 205.171-2 Section 205.171-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

Droplet Size-Aware and Error-Correcting Sample Preparation Using Micro-Electrode-Dot-Array Digital Microfluidic Biochips.

Science.gov (United States)

Li, Zipeng; Lai, Kelvin Yi-Tse; Chakrabarty, Krishnendu; Ho, Tsung-Yi; Lee, Chen-Yi

2017-12-01

Sample preparation in digital microfluidics refers to the generation of droplets with target concentrations for on-chip biochemical applications. In recent years, digital microfluidic biochips (DMFBs) have been adopted as a platform for sample preparation. However, there remain two major problems associated with sample preparation on a conventional DMFB. First, only a (1:1) mixing/splitting model can be used, leading to an increase in the number of fluidic operations required for sample preparation. Second, only a limited number of sensors can be integrated on a conventional DMFB; as a result, the latency for error detection during sample preparation is significant. To overcome these drawbacks, we adopt a next generation DMFB platform, referred to as micro-electrode-dot-array (MEDA), for sample preparation. We propose the first sample-preparation method that exploits the MEDA-specific advantages of fine-grained control of droplet sizes and real-time droplet sensing. Experimental demonstration using a fabricated MEDA biochip and simulation results highlight the effectiveness of the proposed sample-preparation method.

Automated Blood Sample Preparation Unit (ABSPU) for Portable Microfluidic Flow Cytometry.

Science.gov (United States)

Chaturvedi, Akhil; Gorthi, Sai Siva

2017-02-01

Portable microfluidic diagnostic devices, including flow cytometers, are being developed for point-of-care settings, especially in conjunction with inexpensive imaging devices such as mobile phone cameras. However, two pervasive drawbacks of these have been the lack of automated sample preparation processes and cells settling out of sample suspensions, leading to inaccurate results. We report an automated blood sample preparation unit (ABSPU) to prevent blood samples from settling in a reservoir during loading of samples in flow cytometers. This apparatus automates the preanalytical steps of dilution and staining of blood cells prior to microfluidic loading. It employs an assembly with a miniature vibration motor to drive turbulence in a sample reservoir. To validate performance of this system, we present experimental evidence demonstrating prevention of blood cell settling, cell integrity, and staining of cells prior to flow cytometric analysis. This setup is further integrated with a microfluidic imaging flow cytometer to investigate cell count variability. With no need for prior sample preparation, a drop of whole blood can be directly introduced to the setup without premixing with buffers manually. Our results show that integration of this assembly with microfluidic analysis provides a competent automation tool for low-cost point-of-care blood-based diagnostics.

Error Analysis of Ceramographic Sample Preparation for Coating Thickness Measurement of Coated Fuel Particles

International Nuclear Information System (INIS)

Liu Xiaoxue; Li Ziqiang; Zhao Hongsheng; Zhang Kaihong; Tang Chunhe

2014-01-01

The thicknesses of four coatings of HTR coated fuel particle are very important parameters. It is indispensable to control the thickness of four coatings of coated fuel particles for the safety of HTR. A measurement method, ceramographic sample-microanalysis method, to analyze the thickness of coatings was developed. During the process of ceramographic sample-microanalysis, there are two main errors, including ceramographic sample preparation error and thickness measurement error. With the development of microscopic techniques, thickness measurement error can be easily controlled to meet the design requirements. While, due to the coated particles are spherical particles of different diameters ranged from 850 to 1000μm, the sample preparation process will introduce an error. And this error is different from one sample to another. It’s also different from one particle to another in the same sample. In this article, the error of the ceramographic sample preparation was calculated and analyzed. Results show that the error introduced by sample preparation is minor. The minor error of sample preparation guarantees the high accuracy of the mentioned method, which indicates this method is a proper method to measure the thickness of four coatings of coated particles. (author)

[Generic drugs: good or bad? Physician's knowledge of generic drugs and prescribing habits].

Science.gov (United States)

García, A J; Martos, F; Leiva, F; Sánchez de la Cuesta, F

2003-01-01

In this article we analyze the responses of 1220 Spanish physicians who participated in a survery about generic drugs. A previously validated questionnaire was sent to physicians through the Spanish Medical Councils of the different provinces. Four items were analyzed: what doctors know about generic drugs (knowledge); physicians' prescribing habits concerning these drugs (attitude and professional competence); how prescription of generic drugs effects pharmaceutical costs amd, finally, what doctors believe a generic drug should be. The influence of physician-related variables (age, type of contract, specialty, workload, etc.) on prescribing of generic drugs was also analyzed. In view of the results, we believe that to rationalize expenditure through and appropriate policy on generic drugs Spanish health authorities should offer more and better training and information (clear and independent) about what generic drugs are.

Bioequivalence study of a generic Risperidone (Iperdal® in healthy Thai male volunteers

Directory of Open Access Journals (Sweden)

Werawath Mahatthanatrakul

2008-05-01

Full Text Available The objective of this study was to compare the rate and extent of absorption of a generic risperidone (Iperdal® with a reference formulation (Risperdal® when given orally. The study was an open label, randomized, two-period, two-sequence,single dose cross-over design with a 2 weeks washout period in 16 healthy Thai male volunteers. Single oral dose of two 2-mg tablets of risperidone were administered and serial blood samples were collected from the antecubital vein before and at0.17, 0.33, 0.5, 0.75, 1.0, 1.5, 2.0, 3.0, 4.0, 6.0, 8.0, 12, 24 and 48 hours post dose. Risperidone plasma concentrations were assayed using a validated High Performance Liquid Chromatographic (HPLC-UV method modified from Avenosoet al. (2000. Pharamcokinetic parameters i.e. Cmax, AUC0à48 and Tmax were analyzed by noncompartment analysis. Variations of the data were analyzed by “Two Way Analysis of Variance” (ANOVA. Statistics were tested as stated in USP 28 guidelinefor bioequivalence study. The maximum concentration (Cmax, ng/ml of risperidone for the innovator and the generic product were 31.11±17.24 (range 5.64-56.78 and 32.58±19.77 (range 5.29-84.56 ng/ml, respectively. The area under theplasma concentration-time curve (AUC0®48 of the innovator and the generic product were 160.64±152.89 (range 18.57- 550.32 and 144.03±127.37 (range 16.27-456.0 ng.hr/ml, respectively. The time to maximum concentration (Tmax of theinnovator and the generic product were 0.97±0.41(range 0.5-2 and 1.02±0.32 (range 0.5-1.5 hr, respectively. The 90% confidence interval of the ratio of the ln-transformed of Cmax and AUC0à48 of both preparations were 89.39-112.99% and80.02-107.28% respectively which were within the acceptance range of 80.00-125.00%. Therefore, it can be concluded that both preparations used in this study are bioequivalent in terms of both the rate and extent of absorption.

Miniaturizing EM Sample Preparation: Opportunities, Challenges, and "Visual Proteomics".

Science.gov (United States)

Arnold, Stefan A; Müller, Shirley A; Schmidli, Claudio; Syntychaki, Anastasia; Rima, Luca; Chami, Mohamed; Stahlberg, Henning; Goldie, Kenneth N; Braun, Thomas

2018-03-01

This review compares and discusses conventional versus miniaturized specimen preparation methods for transmission electron microscopy (TEM). The progress brought by direct electron detector cameras, software developments and automation have transformed transmission cryo-electron microscopy (cryo-EM) and made it an invaluable high-resolution structural analysis tool. In contrast, EM specimen preparation has seen very little progress in the last decades and is now one of the main bottlenecks in cryo-EM. Here, we discuss the challenges faced by specimen preparation for single particle EM, highlight current developments, and show the opportunities resulting from the advanced miniaturized and microfluidic sample grid preparation methods described, such as visual proteomics and time-resolved cryo-EM studies. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Optimized preparation of urine samples for two-dimensional electrophoresis and initial application to patient samples

DEFF Research Database (Denmark)

Lafitte, Daniel; Dussol, Bertrand; Andersen, Søren

2002-01-01

OBJECTIVE: We optimized of the preparation of urinary samples to obtain a comprehensive map of urinary proteins of healthy subjects and then compared this map with the ones obtained with patient samples to show that the pattern was specific of their kidney disease. DESIGN AND METHODS: The urinary...

Analytical characterization of high-level mixed wastes using multiple sample preparation treatments

International Nuclear Information System (INIS)

King, A.G.; Baldwin, D.L.; Urie, M.W.; McKinley, S.G.

1994-01-01

The Analytical Chemistry Laboratory at the Pacific Northwest Laboratory in Richland, Washington, is actively involved in performing analytical characterization of high-level mixed waste from Hanford's single shell and double shell tank characterization programs. A full suite of analyses is typically performed on homogenized tank core samples. These analytical techniques include inductively-coupled plasma-atomic emission spectroscopy, total organic carbon methods and radiochemistry methods, as well as many others, all requiring some type of remote sample-preparation treatment to solubilize the tank sludge material for analysis. Most of these analytical methods typically use a single sample-preparation treatment, inherently providing elemental information only. To better understand and interpret tank chemistry and assist in identifying chemical compounds, selected analytical methods are performed using multiple sample-preparation treatments. The sample preparation treatments used at Pacific Northwest Laboratory for this work with high-level mixed waste include caustic fusion, acid digestion, and water leach. The type of information available by comparing results from different sample-prep treatments includes evidence for the presence of refractory compounds, acid-soluble compounds, or water-soluble compounds. Problems unique to the analysis of Hanford tank wastes are discussed. Selected results from the Hanford single shell ferrocyanide tank, 241-C-109, are presented, and the resulting conclusions are discussed

Novel sample preparation for operando TEM of catalysts

International Nuclear Information System (INIS)

Miller, Benjamin K.; Barker, Trevor M.; Crozier, Peter A.

2015-01-01

A new TEM sample preparation method is developed to facilitate operando TEM of gas phase catalysis. A porous Pyrex-fiber pellet TEM sample was produced, allowing a comparatively large amount of catalyst to be loaded into a standard Gatan furnace-type tantalum heating holder. The increased amount of catalyst present inside the environmental TEM allows quantitative determination of the gas phase products of a catalytic reaction performed in-situ at elevated temperatures. The product gas concentration was monitored using both electron energy loss spectroscopy (EELS) and residual gas analysis (RGA). Imaging of catalyst particles dispersed over the pellet at atomic resolution is challenging, due to charging of the insulating glass fibers. To overcome this limitation, a metal grid is placed into the holder in addition to the pellet, allowing catalyst particles dispersed over the grid to be imaged, while particles in the pellet, which are assumed to experience identical conditions, contribute to the overall catalytic conversion inside the environmental TEM cell. The gas within the cell is determined to be well-mixed, making this assumption reasonable. - Highlights: • High in-situ conversion of CO to CO 2 achieved by a novel TEM sample preparation method. • A 3 mm fiber pellet increases the TEM sample surface area by 50×. • Operando atomic resolution is maintained by also including a 3 mm grid in the sample. • Evidence for a well-mixed gas composition inside the ETEM cell is given

Modern methods of sample preparation for GC analysis

NARCIS (Netherlands)

de Koning, S.; Janssen, H.-G.; Brinkman, U.A.Th.

2009-01-01

Today, a wide variety of techniques is available for the preparation of (semi-) solid, liquid and gaseous samples, prior to their instrumental analysis by means of capillary gas chromatography (GC) or, increasingly, comprehensive two-dimensional GC (GC × GC). In the past two decades, a large number

Collection and preparation of wet and dry stream-sediment samples

International Nuclear Information System (INIS)

Puchlik, K.

1977-03-01

Lawrence Livermore Laboratory is responsible for the Hydrogeochemistry and Stream Sediment Reconnaissance (HSSR) program for uranium in the seven far western states. The work thus far has concentrated on the arid to semi-arid regions of the West and this paper discusses the collection and preparation of sediment samples in the Basin and Range province. The sample collection and preparation procedures described here may not be applicable to other parts of the far western states or other areas. These procedures also differ somewhat from those used by the other three laboratories involved in the HSSR program

Sampling and sample preparation methods for the analysis of trace elements in biological material

International Nuclear Information System (INIS)

Sansoni, B.; Iyengar, V.

1978-05-01

The authors attempt to give a most systamtic possible treatment of the sample taking and sample preparation of biological material (particularly in human medicine) for trace analysis (e.g. neutron activation analysis, atomic absorption spectrometry). Contamination and loss problems are discussed as well as the manifold problems of the different consistency of solid and liquid biological materials, as well as the stabilization of the sample material. The process of dry and wet ashing is particularly dealt with, where new methods are also described. (RB) [de

Sample preparation with solid phase microextraction and exhaustive extraction approaches: Comparison for challenging cases.

Science.gov (United States)

Boyacı, Ezel; Rodríguez-Lafuente, Ángel; Gorynski, Krzysztof; Mirnaghi, Fatemeh; Souza-Silva, Érica A; Hein, Dietmar; Pawliszyn, Janusz

2015-05-11

In chemical analysis, sample preparation is frequently considered the bottleneck of the entire analytical method. The success of the final method strongly depends on understanding the entire process of analysis of a particular type of analyte in a sample, namely: the physicochemical properties of the analytes (solubility, volatility, polarity etc.), the environmental conditions, and the matrix components of the sample. Various sample preparation strategies have been developed based on exhaustive or non-exhaustive extraction of analytes from matrices. Undoubtedly, amongst all sample preparation approaches, liquid extraction, including liquid-liquid (LLE) and solid phase extraction (SPE), are the most well-known, widely used, and commonly accepted methods by many international organizations and accredited laboratories. Both methods are well documented and there are many well defined procedures, which make them, at first sight, the methods of choice. However, many challenging tasks, such as complex matrix applications, on-site and in vivo applications, and determination of matrix-bound and free concentrations of analytes, are not easily attainable with these classical approaches for sample preparation. In the last two decades, the introduction of solid phase microextraction (SPME) has brought significant progress in the sample preparation area by facilitating on-site and in vivo applications, time weighted average (TWA) and instantaneous concentration determinations. Recently introduced matrix compatible coatings for SPME facilitate direct extraction from complex matrices and fill the gap in direct sampling from challenging matrices. Following introduction of SPME, numerous other microextraction approaches evolved to address limitations of the above mentioned techniques. There is not a single method that can be considered as a universal solution for sample preparation. This review aims to show the main advantages and limitations of the above mentioned sample

Automated dried blood spots standard and QC sample preparation using a robotic liquid handler.

Science.gov (United States)

Yuan, Long; Zhang, Duxi; Aubry, Anne-Francoise; Arnold, Mark E

2012-12-01

A dried blood spot (DBS) bioanalysis assay involves many steps, such as the preparation of standard (STD) and QC samples in blood, the spotting onto DBS cards, and the cutting-out of the spots. These steps are labor intensive and time consuming if done manually, which, therefore, makes automation very desirable in DBS bioanalysis. A robotic liquid handler was successfully applied to the preparation of STD and QC samples in blood and to spot the blood samples onto DBS cards using buspirone as the model compound. This automated preparation was demonstrated to be accurate and consistent. However the accuracy and precision of automated preparation were similar to those from manual preparation. The effect of spotting volume on accuracy was evaluated and a trend of increasing concentrations of buspirone with increasing spotting volumes was observed. The automated STD and QC sample preparation process significantly improved the efficiency, robustness and safety of DBS bioanalysis.

Green sample preparation for liquid chromatography and capillary electrophoresis of anionic and cationic analytes.

Science.gov (United States)

Wuethrich, Alain; Haddad, Paul R; Quirino, Joselito P

2015-04-21

A sample preparation device for the simultaneous enrichment and separation of cationic and anionic analytes was designed and implemented in an eight-channel configuration. The device is based on the use of an electric field to transfer the analytes from a large volume of sample into small volumes of electrolyte that was suspended into two glass micropipettes using a conductive hydrogel. This simple, economical, fast, and green (no organic solvent required) sample preparation scheme was evaluated using cationic and anionic herbicides as test analytes in water. The analytical figures of merit and ecological aspects were evaluated against the state-of-the-art sample preparation, solid-phase extraction. A drastic reduction in both sample preparation time (94% faster) and resources (99% less consumables used) was observed. Finally, the technique in combination with high-performance liquid chromatography and capillary electrophoresis was applied to analysis of quaternary ammonium and phenoxypropionic acid herbicides in fortified river water as well as drinking water (at levels relevant to Australian guidelines). The presented sustainable sample preparation approach could easily be applied to other charged analytes or adopted by other laboratories.

Impact of brand or generic labeling on medication effectiveness and side effects.

Science.gov (United States)

Faasse, Kate; Martin, Leslie R; Grey, Andrew; Gamble, Greg; Petrie, Keith J

2016-02-01

Branding medication with a known pharmaceutical company name or product name bestows on the drug an added assurance of authenticity and effectiveness compared to a generic preparation. This study examined the impact of brand name and generic labeling on medication effectiveness and side effects. 87 undergraduate students with frequent headaches took part in the study. Using a within-subjects counterbalanced design, each participant took tablets labeled either as brand name "Nurofen" or "Generic Ibuprofen" to treat each of 4 headaches. In reality, half of the tablets were placebos, and half were active ibuprofen (400 mg). Participants recorded their headache pain on a verbal descriptor and visual analogue scale prior to taking the tablets, and again 1 hour afterward. Medication side effects were also reported. Pain reduction following the use of brand name labeled tablets was similar in active ibuprofen or a placebo. However, if the tablets had a generic label, placebo tablets were significantly less effective compared to active ibuprofen. Fewer side effects were attributed to placebo tablets with brand name labeling compared to the same placebo tablets with a generic label. Branding of a tablet appears to have conferred a treatment benefit in the absence of an active ingredient, while generic labeled tablets were substantially less effective if they contained no active ingredient. Branding is also associated with reduced attribution of side effects to placebo tablets. Future interventions to improve perceptions of generics may have utility in improving treatment outcomes from generic drugs. (c) 2016 APA, all rights reserved).

Brand vs generic adverse event reporting patterns: An authorized generic-controlled evaluation of cardiovascular medications.

Science.gov (United States)

Alatawi, Y; Rahman, Md M; Cheng, N; Qian, J; Peissig, P L; Berg, R L; Page, C D; Hansen, R A

2018-06-01

Some public scepticism exists about generics in terms of whether brand and generic drugs produce identical outcomes. This study explores whether adverse event (AE) reporting patterns are similar between brand and generic drugs, using authorized generics (AGs) as a control for possible generic drug perception biases. Events reported to the FDA Adverse Event Reporting System from the years 2004-2015 were analysed. Drugs were classified as brand, AG or generic based on drug and manufacturer names. Reports were included if amlodipine, losartan, metoprolol extended release (ER) or simvastatin were listed as primary or secondary suspect drugs. Disproportionality analyses using the reporting odds ratio (ROR) assessed the relative rate of reporting labelled AEs compared to reporting these AEs with all other drugs. The Breslow-Day test compared RORs across brand, AG and generic. Interrupted time series analysis evaluated the impact of generic entry on reporting trends. Generics accounted for significant percentages of total U.S. reports, but AGs accounted for smaller percentages of reports, including for amlodipine (14.26%), losartan (1.48%), metoprolol ER (0.35%) and simvastatin (0.70%). Whereas the RORs were significantly different for multiple brand vs generic comparisons, the AG vs generic comparisons yielded fewer statistically significant findings. Namely, only the ROR for AG differed from generic for amlodipine with peripheral oedema (P brand and generic compared with AG and generic. Use of AGs as a control for perception biases against generics is useful, but this approach can be limited by small AG report numbers. Requiring the manufacturer name to be printed on the prescription bottle or packaging could improve the accuracy of assignment for products being reported. © 2017 John Wiley & Sons Ltd.

Independent assessment of matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) sample preparation quality : Effect of sample preparation on MALDI-MS of synthetic polymers

NARCIS (Netherlands)

Kooijman, Pieter C.; Kok, Sander; Honing, Maarten

2017-01-01

Rationale: Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) provides detailed and in-depth information about the molecular characteristics of synthetic polymers. To obtain the most accurate results the sample preparation parameters should be chosen to suit the sample and the

Sample Preparation of Corn Seed Tissue to Prevent Analyte Relocations for Mass Spectrometry Imaging

Science.gov (United States)

Kim, Shin Hye; Kim, Jeongkwon; Lee, Young Jin; Lee, Tae Geol; Yoon, Sohee

2017-08-01

Corn seed tissue sections were prepared by the tape support method using an adhesive tape, and mass spectrometry imaging (MSI) was performed. The effect of heat generated during sample preparation was investigated by time-of-flight secondary mass spectrometry (TOF-SIMS) imaging of corn seed tissue prepared by the tape support and the thaw-mounted methods. Unlike thaw-mounted sample preparation, the tape support method does not cause imaging distortion because of the absence of heat, which can cause migration of the analytes on the sample. By applying the tape-support method, the corn seed tissue was prepared without structural damage and MSI with accurate spatial information of analytes was successfully performed.

Sample Preparation of Corn Seed Tissue to Prevent Analyte Relocations for Mass Spectrometry Imaging.

Science.gov (United States)

Kim, Shin Hye; Kim, Jeongkwon; Lee, Young Jin; Lee, Tae Geol; Yoon, Sohee

2017-08-01

Corn seed tissue sections were prepared by the tape support method using an adhesive tape, and mass spectrometry imaging (MSI) was performed. The effect of heat generated during sample preparation was investigated by time-of-flight secondary mass spectrometry (TOF-SIMS) imaging of corn seed tissue prepared by the tape support and the thaw-mounted methods. Unlike thaw-mounted sample preparation, the tape support method does not cause imaging distortion because of the absence of heat, which can cause migration of the analytes on the sample. By applying the tape-support method, the corn seed tissue was prepared without structural damage and MSI with accurate spatial information of analytes was successfully performed. Graphical Abstract ᅟ.

Universal Sample Preparation Module for Molecular Analysis in Space, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Lynntech proposes to develop and demonstrate the ability of a compact, light-weight, and automated universal sample preparation module (USPM) to process samples from...

Recent developments in sample preparation and data pre-treatment in metabonomics research.

Science.gov (United States)

Li, Ning; Song, Yi peng; Tang, Huiru; Wang, Yulan

2016-01-01

Metabonomics is a powerful approach for biomarker discovery and an effective tool for pinpointing endpoint metabolic effects of external stimuli, such as pathogens and disease development. Due to its wide applications, metabonomics is required to deal with various biological samples of different properties. Hence sample preparation and corresponding data pre-treatment become important factors in ensuring validity of an investigation. In this review, we summarize some recent developments in metabonomics sample preparation and data-pretreatment procedures. Copyright © 2015 Elsevier Inc. All rights reserved.

Current advances and strategies towards fully automated sample preparation for regulated LC-MS/MS bioanalysis.

Science.gov (United States)

Zheng, Naiyu; Jiang, Hao; Zeng, Jianing

2014-09-01

Robotic liquid handlers (RLHs) have been widely used in automated sample preparation for liquid chromatography-tandem mass spectrometry (LC-MS/MS) bioanalysis. Automated sample preparation for regulated bioanalysis offers significantly higher assay efficiency, better data quality and potential bioanalytical cost-savings. For RLHs that are used for regulated bioanalysis, there are additional requirements, including 21 CFR Part 11 compliance, software validation, system qualification, calibration verification and proper maintenance. This article reviews recent advances in automated sample preparation for regulated bioanalysis in the last 5 years. Specifically, it covers the following aspects: regulated bioanalysis requirements, recent advances in automation hardware and software development, sample extraction workflow simplification, strategies towards fully automated sample extraction, and best practices in automated sample preparation for regulated bioanalysis.

Generic antibiotics in Japan.

Science.gov (United States)

Fujimura, Shigeru; Watanabe, Akira

2012-08-01

Generic drugs have been used extensively in many developed countries, although their use in Japan has been limited. Generic drugs reduce drug expenses and thereby national medical expenditure. Because generic drugs provide advantages for both public administration and consumers, it is expected that they will be more widely used in the future. However, the diffusion rate of generic drugs in Japan is quite low compared with that of other developed countries. An investigation on generic drugs conducted by the Ministry of Health, Labour and Welfare in Japan revealed that 17.2 % of doctors and 37.2 % of patients had not used generic drugs. The major reasons for this low use rate included distrust of off-patent products and lower drug price margin compared with the brand name drug. The generic drugs available in the market include external drugs such as wet packs, antihypertensive agents, analgesics, anticancer drugs, and antibiotics. Among them, antibiotics are frequently used in cases of acute infectious diseases. When the treatment of these infections is delayed, the infection might be aggravated rapidly. The pharmacokinetics-pharmacodynamics (PK-PD) theory has been adopted in recent chemotherapy, and in many cases, the most appropriate dosage and administration of antibiotics are determined for individual patients considering renal function; high-dosage antibiotics are used preferably for a short duration. Therefore, a highly detailed antimicrobial agent is necessary. However, some of the generic antibiotics have less antibacterial potency or solubility than the brand name products. We showed that the potency of the generic products of vancomycin and teicoplanin is lower than that of the branded drugs by 14.6 % and 17.3 %, respectively. Furthermore, we confirmed that a generic meropenem drug for injection required about 82 s to solubilize in saline, whereas the brand product required only about 21 s. It was thought that the cause may be the difference in size of bulk

A new generic system for the pantropical Caesalpinia group (Leguminosae

Directory of Open Access Journals (Sweden)

Edeline Gagnon

2016-10-01

Full Text Available The Caesalpinia group is a large pantropical clade of ca. 205 species in subfamily Caesalpinioideae (Leguminosae in which generic delimitation has been in a state of considerable flux. Here we present new phylogenetic analyses based on five plastid and one nuclear ribosomal marker, with dense taxon sampling including 172 (84% of the species and representatives of all previously described genera in the Caesalpinia group. These analyses show that the current classification of the Caesalpinia group into 21 genera needs to be revised. Several genera (Poincianella, Erythrostemon, Cenostigma and Caesalpinia sensu Lewis, 2005 are non-monophyletic and several previously unclassified Asian species segregate into clades that merit recognition at generic rank. In addition, the near-completeness of our taxon sampling identifies three species that do not belong in any of the main clades and these are recognised as new monospecific genera. A new generic classification of the Caesalpinia group is presented including a key for the identification of genera, full generic descriptions, illustrations (drawings and photo plates of all genera, and (for most genera the nomenclatural transfer of species to their correct genus. We recognise 26 genera, with reinstatement of two previously described genera (Biancaea Tod., Denisophytum R. Vig., re-delimitation and expansion of several others (Moullava, Cenostigma, Libidibia and Erythrostemon, contraction of Caesalpinia s.s. and description of four new ones (Gelrebia, Paubrasilia, Hererolandia and Hultholia, and make 75 new nomenclatural combinations in this new generic system.

Synthesis and application of magnetic molecularly imprinted polymers in sample preparation.

Science.gov (United States)

Huang, Shuyao; Xu, Jianqiao; Zheng, Jiating; Zhu, Fang; Xie, Lijun; Ouyang, Gangfeng

2018-04-12

Magnetic molecularly imprinted polymers (MMIPs) have superior advantages in sample pretreatment because of their high selectivity for target analytes and the fast and easy isolation from samples. To meet the demand of both good magnetic property and good extraction performance, MMIPs with various structures, from traditional core-shell structures to novel composite structures with a larger specific surface area and more accessible binding sites, are fabricated by different preparation technologies. Moreover, as the molecularly imprinted polymer (MIP) layers determine the affinity, selectivity, and saturated adsorption amount of MMIPs, the development and innovation of the MIP layer are attracting attention and are reviewed here. Many studies that used MMIPs as sorbents in dispersive solid-phase extraction of complex samples, including environmental, food, and biofluid samples, are summarized. Graphical abstract The application of magnetic molecularly imprinted polymers (MIPs) in the sample preparation procedure improves the analytical performances for complex samples. MITs molecular imprinting technologies.

Sample preparation and detection device for infectious agents

Science.gov (United States)

Miles, Robin R.; Wang, Amy W.; Fuller, Christopher K.; Lemoff, Asuncion V.; Bettencourt, Kerry A.; Yu, June

2003-06-10

A sample preparation and analysis device which incorporates both immunoassays and PCR assays in one compact, field-portable microchip. The device provides new capabilities in fluid and particle control which allows the building of a fluidic chip with no moving parts, thus decreasing fabrication cost and increasing the robustness of the device. The device can operate in a true continuous (not batch) mode. The device incorporates magnetohydrodynamic (MHD) pumps to move the fluid through the system, acoustic mixing and fractionation, dielectropheretic (DEP) sample concentration and purification, and on-chip optical detection capabilities.

76 FR 79702 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-12-22

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential... Qualitative Feedback on Agency Service Delivery AGENCY: National Institute of Mental Health (NIMH), HHS... Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency...

78 FR 40729 - Agency Information Collection Activities; Proposed Collection; Comment Request: Generic Clearance...

Science.gov (United States)

2013-07-08

... precision requirements or power calculations that justify the proposed sample size, the expected response... Qualitative Feedback on Agency Service Delivery AGENCY: Washington Headquarters Service (WHS), DOD. ACTION: 30... (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery...

76 FR 21746 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-04-18

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential... of Qualitative Feedback on Agency Service Delivery AGENCY: Agency for Healthcare Research and Quality... Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency...

76 FR 41280 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-07-13

... proposed sample size, the expected response rate, methods for assessing potential non-response bias, the... Activities: Proposed Collection; Comment Request; Generic Clearance for the Collection of Qualitative...): ``Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery '' to OMB for...

GenMed 010: a one day workshop on generic medicines

Directory of Open Access Journals (Sweden)

Shankar PR

2011-03-01

Full Text Available This report outlines the content of a one-day workshop onGeneric Medicines that was held at KIST Medical College,Lalitpur, Nepal on 13th December 2010, which was attendedby 32 delegates from different institutions in Nepal, includingpharmacists, pharmacologists and medical doctors. Rightmedicine, right patient, right dose, right frequency andduration, right information and right monitoring areconditions to be fulfilled for the rational use of medicine(RUM. The World Health Organization (WHO defines genericmedicine as ‘a pharmaceutical product, usually intended to beinterchangeable with the innovator product, marketed afterthe expiry of patent or other exclusivity rights’. Economicfactors, supportive legislation and regulation, public andprofessional acceptance and quality assurance are keyenabling factors promoting use of generics. Increased patentprotection for medicines and removing process patents is akey feature of new trade agreements and newer medicines fordiseases like HIV/AIDS, tuberculosis and infectious diseasesare likely to be more expensive. The Medicine andTherapeutics Committee (MTC can play a key role inpromoting generic medicine use in institutions.Nepal being among the Least Developed Countries (LDCsneed not provide patent protection for medicines until 31stDecember 2015. Only a few ‘true’ generics are available inNepal and there is huge cost variation in the price of differentbranded generics. Clinicians have concerns about the qualityof medicines in general, substitution of poor quality brands bypharmacists and about therapeutic substitution. Genericshave to meet the same regulatory requirements and bebioequivalent to reference preparations assuring their quality.

Scripting XML with Generic Haskell

NARCIS (Netherlands)

Atanassow, F.; Clarke, D.; Jeuring, J.T.

2003-01-01

A generic program is written once and works on values of many data types. Generic Haskell is a recent extension of the functional programming language Haskell that supports generic programming. This paper discusses how Generic Haskell can be used to implement XML tools whose behaviour depends on

Scripting XML with Generic Haskell

NARCIS (Netherlands)

Atanassow, F.; Clarke, D.; Jeuring, J.T.

2007-01-01

A generic program is written once and works on values of many data types. Generic Haskell is a recent extension of the functional programming language Haskell that supports generic programming. This paper discusses how Generic Haskell can be used to implement XML tools whose behaviour depends on

Consumer choice between common generic and brand medicines in a country with a small generic market.

Science.gov (United States)

Fraeyman, Jessica; Peeters, Lies; Van Hal, Guido; Beutels, Philippe; De Meyer, Guido R Y; De Loof, Hans

2015-04-01

Generic medicines offer an opportunity for governments to contain pharmaceutical expenditures, since generics are generally 10%-80% lower in price than brand medicines. Belgium has a small generic market that takes up 15% of the total pharmaceutical market in packages sold. To determine the knowledge of consumers about the different available packages of a common over-the-counter medicine (acetaminophen) with regard to price advantage, quality, and effectiveness in a country with a small generic market. We conducted an online survey in the general Flemish population using a questionnaire with 25 statements. The questionnaire also contained 2 informative interventions. First, we showed the price per package and per tablet that the patient would pay in the pharmacy. Second, we provided the respondent with general information about generic medication (equivalence, effectiveness, price, and recognition). Before and after the interventions, we probed for preferences and knowledge about the different packages. Multivariate logistic models were used to examine the independent effects of consumer characteristics on responses to the survey statements. We obtained a sample of 1,636 respondents. The general attitude towards generic medication was positive-only 5% would rather not use a generic. Nevertheless, only 17% of the respondents were able to recognize a generic medicine. Older consumers (aged 60 years and above) were more often confused about the different packages (OR = 2.59, 95% CI = 1.76-3.80, P ≤ 0.001). Consumers without a higher education degree tended to be more doubtful about the difference in effectiveness and quality between the different brands (OR = 0.59, 95% CI = 0.44-0.79, P ≤ 0.001). Consumer recognition of the name of the active substance of acetaminophen was poor. When different brands were displayed, possible price advantage seemed to be an important motive to switch to a cheaper brand. Consumers generally found medicines

High-resolution X-ray diffraction with no sample preparation.

Science.gov (United States)

Hansford, G M; Turner, S M R; Degryse, P; Shortland, A J

2017-07-01

It is shown that energy-dispersive X-ray diffraction (EDXRD) implemented in a back-reflection geometry is extremely insensitive to sample morphology and positioning even in a high-resolution configuration. This technique allows high-quality X-ray diffraction analysis of samples that have not been prepared and is therefore completely non-destructive. The experimental technique was implemented on beamline B18 at the Diamond Light Source synchrotron in Oxfordshire, UK. The majority of the experiments in this study were performed with pre-characterized geological materials in order to elucidate the characteristics of this novel technique and to develop the analysis methods. Results are presented that demonstrate phase identification, the derivation of precise unit-cell parameters and extraction of microstructural information on unprepared rock samples and other sample types. A particular highlight was the identification of a specific polytype of a muscovite in an unprepared mica schist sample, avoiding the time-consuming and difficult preparation steps normally required to make this type of identification. The technique was also demonstrated in application to a small number of fossil and archaeological samples. Back-reflection EDXRD implemented in a high-resolution configuration shows great potential in the crystallographic analysis of cultural heritage artefacts for the purposes of scientific research such as provenancing, as well as contributing to the formulation of conservation strategies. Possibilities for moving the technique from the synchrotron into museums are discussed. The avoidance of the need to extract samples from high-value and rare objects is a highly significant advantage, applicable also in other potential research areas such as palaeontology, and the study of meteorites and planetary materials brought to Earth by sample-return missions.

77 FR 72361 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2012-12-05

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential... Qualitative Feedback on Agency Service Delivery SUMMARY: As part of a Federal Government-wide effort to... Information Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback...

76 FR 44938 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-07-27

... calculations that justify the proposed sample size, the expected response rate, methods for assessing potential... Qualitative Feedback on Agency Service Delivery: National Cancer Center (NCI) ACTION: 30-Day notice of... Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency...

Application of immunoaffinity columns for different food item samples preparation in micotoxins determination

Directory of Open Access Journals (Sweden)

Ćurčić Marijana

2016-01-01

Full Text Available In analytical methods used for monitoring of what special attention is paid to sample preparation. Therefore, the objective of this study was testing the efficiency of immunoaffinity columns (IAC that are based on solid phase extraction principles used for samples preparation in determining aflatoxins and ochratoxins. Aflatoxins and ochratoxins concentrations were determined in totally 56 samples of food items: wheat, corn, rice, barley and other grains (19 samples, flour and flour products from grain and additives for the bakery industry (7 samples, fruits and vegetables (3 samples, hazelnut, walnut, almond, coconut flour (4 samples, roasted cocoa beans, peanuts, tea, coffee (16 samples, spices (4 samples and meat and meat products (4 samples. Obtained results indicate advantage of IAC use for sample preparation based on enhanced specificity due to binding of extracted molecules to incorporated specific antibodies and rinsing the rest molecules from sample which could interfere with further analysis. Additional advantage is the usage of small amount of organic solvents and consequently decreased exposure of staff who conduct micotoxins determination. Of special interest is increase in method sensitivity since limit of quantification for aflatoxins and ochratoxins determination method is lower than maximal allowed concentration of these toxines prescribed by national rule book.

HASE - The Helsinki adaptive sample preparation line

Energy Technology Data Exchange (ETDEWEB)

Palonen, V., E-mail: vesa.palonen@helsinki.fi [Department of Physics, University of Helsinki, P.O. Box 43, FI-00014 (Finland); Pesonen, A. [Laboratory of Chronology, Finnish Museum of Natural History, P.O. Box 64, FI-00014 (Finland); Herranen, T.; Tikkanen, P. [Department of Physics, University of Helsinki, P.O. Box 43, FI-00014 (Finland); Oinonen, M. [Laboratory of Chronology, Finnish Museum of Natural History, P.O. Box 64, FI-00014 (Finland)

2013-01-15

We have designed and built an adaptive sample preparation line with separate modules for combustion, molecular sieve handling, CO{sub 2} gas cleaning, CO{sub 2} storage, and graphitization. The line is also connected to an elemental analyzer. Operation of the vacuum equipment, a flow controller, pressure sensors, ovens, and graphitization reactors are automated with a reliable NI-cRIO real-time system. Stepped combustion can be performed in two ovens at temperatures up to 900 Degree-Sign C. Depending on the application, CuO or O{sub 2}-flow combustion can be used. A flow controller is used to adjust the O{sub 2} flow and pressure during combustion. For environmental samples, a module for molecular sieve regeneration and sample desorption is attached to the line replacing the combustion module. In the storage module, CO{sub 2} samples can be stored behind a gas-tight diaphragm valve and either stored for later graphitization or taken for measurements with separate equipment (AMS gas ion source or a separate mass spectrometer). The graphitization module consists of four automated reactors, capable of graphitizing samples with masses from 3 mg down to 50 {mu}g.

Gel-aided sample preparation (GASP)--a simplified method for gel-assisted proteomic sample generation from protein extracts and intact cells.

Science.gov (United States)

Fischer, Roman; Kessler, Benedikt M

2015-04-01

We describe a "gel-assisted" proteomic sample preparation method for MS analysis. Solubilized protein extracts or intact cells are copolymerized with acrylamide, facilitating denaturation, reduction, quantitative cysteine alkylation, and matrix formation. Gel-aided sample preparation has been optimized to be highly flexible, scalable, and to allow reproducible sample generation from 50 cells to milligrams of protein extracts. This methodology is fast, sensitive, easy-to-use on a wide range of sample types, and accessible to nonspecialists. © 2014 The Authors. PROTEOMICS published by Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Food adulteration analysis without laboratory prepared or determined reference food adulterant values.

Science.gov (United States)

Kalivas, John H; Georgiou, Constantinos A; Moira, Marianna; Tsafaras, Ilias; Petrakis, Eleftherios A; Mousdis, George A

2014-04-01

Quantitative analysis of food adulterants is an important health and economic issue that needs to be fast and simple. Spectroscopy has significantly reduced analysis time. However, still needed are preparations of analyte calibration samples matrix matched to prediction samples which can be laborious and costly. Reported in this paper is the application of a newly developed pure component Tikhonov regularization (PCTR) process that does not require laboratory prepared or reference analysis methods, and hence, is a greener calibration method. The PCTR method requires an analyte pure component spectrum and non-analyte spectra. As a food analysis example, synchronous fluorescence spectra of extra virgin olive oil samples adulterated with sunflower oil is used. Results are shown to be better than those obtained using ridge regression with reference calibration samples. The flexibility of PCTR allows including reference samples and is generic for use with other instrumental methods and food products. Copyright © 2013 Elsevier Ltd. All rights reserved.

A Proteomics Sample Preparation Method for Mature, Recalcitrant Leaves of Perennial Plants

Science.gov (United States)

Na, Zhang; Chengying, Lao; Bo, Wang; Dingxiang, Peng; Lijun, Liu

2014-01-01

Sample preparation is key to the success of proteomics studies. In the present study, two sample preparation methods were tested for their suitability on the mature, recalcitrant leaves of six representative perennial plants (grape, plum, pear, peach, orange, and ramie). An improved sample preparation method was obtained: Tris and Triton X-100 were added together instead of CHAPS to the lysis buffer, and a 20% TCA-water solution and 100% precooled acetone were added after the protein extraction for the further purification of protein. This method effectively eliminates nonprotein impurities and obtains a clear two-dimensional gel electrophoresis array. The method facilitates the separation of high-molecular-weight proteins and increases the resolution of low-abundance proteins. This method provides a widely applicable and economically feasible technology for the proteomic study of the mature, recalcitrant leaves of perennial plants. PMID:25028960

A proteomics sample preparation method for mature, recalcitrant leaves of perennial plants.

Directory of Open Access Journals (Sweden)

Deng Gang

Full Text Available Sample preparation is key to the success of proteomics studies. In the present study, two sample preparation methods were tested for their suitability on the mature, recalcitrant leaves of six representative perennial plants (grape, plum, pear, peach, orange, and ramie. An improved sample preparation method was obtained: Tris and Triton X-100 were added together instead of CHAPS to the lysis buffer, and a 20% TCA-water solution and 100% precooled acetone were added after the protein extraction for the further purification of protein. This method effectively eliminates nonprotein impurities and obtains a clear two-dimensional gel electrophoresis array. The method facilitates the separation of high-molecular-weight proteins and increases the resolution of low-abundance proteins. This method provides a widely applicable and economically feasible technology for the proteomic study of the mature, recalcitrant leaves of perennial plants.

Advances in modern sample preparation techniques using microwaves assisted chemistry for metal species determination (W1)

International Nuclear Information System (INIS)

Ponard, O.F.X.

2002-01-01

Full text: Sample preparation has long been the bottleneck of environmental analysis for both total and species specific analysis. Digestion, extraction and preparation of the analytes are relying on a series of chemical reactions. The introduction of microwave assisted sample preparation has first been viewed as a mean to accelerate the kinetics of digestion of the matrix for total elements and fast samples preparation procedures. However, the extensive development and success of microwave digestion procedures in total elemental analysis has now allowed to have a larger insight of the perspectives offered by this technique. Microwave technologies now offer to have a precise control of the temperature and indirectly control the reaction kinetics taking place during the sample preparation procedures. Microwave assisted chemistry permits to perform simultaneously the fundamental steps required for metal species extraction and derivatization. The number of sample preparation steps used for organotin or organomercury species have been reduced to one and the total time of sample preparation brought down for a few hours to some minutes. Further, the developments of GC/ICP/MS techniques allow to routinely use speciated isotopic dilution methods has internal probe of the chemical reactions. These new approaches allow us to use the addition of the labeled species for isotopic dilution as a mean to evaluate and follow the chemical processes taking place during the extraction procedure. These procedures will help us to understand and check for the stability of the analytes during the chemistry of the sample preparation procedure and bring some insights of the chemistry taking place during the extraction. Understanding the different mechanisms involved in the sample preparation steps will allow us in return to further improve all theses procedures and bring us to the horizon of 'on-line sample preparation and detection'. (author)

Predictors of generic substitution: The role of psychological, sociodemographic, and contextual factors.

Science.gov (United States)

Drozdowska, Aleksandra; Hermanowski, Tomasz

2016-01-01

Escalating pharmaceutical costs have become a global challenge for both governments and patients. Generic substitution is one way of decreasing these costs. The aim of this study was to investigate factors associated with patients' choice between generic drugs and innovator drugs. The survey was conducted in June 2013, 1000 people from across Poland were chosen as a representative population sample. The outcome (a preference for generics/a preference for innovator pharmaceuticals/no preference) was modeled by multinomial logistic regression, adjusted for several variables describing patients' sensitivity to selected generic features (price, brand, and country of origin), to third-party opinions about generics (information on generics in the mass media, opinions of health professionals (i.e. physicians, pharmacists), relatives/friends), as well as patients' personal experiences and income per household. The results supported the predictive capacity of most independent variables (except for patient sensitivity to the country of origin and to the information on generics in the mass media), denoting patients' preferences toward generic substitution. Patient sensitivity to recommendations by physicians, generic brand, and household income were the strongest predictors of the choice between generic and innovator pharmaceuticals (P brand or their physician's opinion, as well as in respondents who were sensitive to recommendations by pharmacists or attached a greater value to a past experience with generics (their own experience or that of relatives/friends). In consideration of the foregoing, awareness-raising campaigns may be recommended, supported by a variety of systemic solutions and tools to encourage generic substitution. Copyright © 2016 Elsevier Inc. All rights reserved.

On the use of ultracentrifugal devices for routine sample preparation in biomolecular magic-angle-spinning NMR.

Science.gov (United States)

Mandal, Abhishek; Boatz, Jennifer C; Wheeler, Travis B; van der Wel, Patrick C A

2017-03-01

A number of recent advances in the field of magic-angle-spinning (MAS) solid-state NMR have enabled its application to a range of biological systems of ever increasing complexity. To retain biological relevance, these samples are increasingly studied in a hydrated state. At the same time, experimental feasibility requires the sample preparation process to attain a high sample concentration within the final MAS rotor. We discuss these considerations, and how they have led to a number of different approaches to MAS NMR sample preparation. We describe our experience of how custom-made (or commercially available) ultracentrifugal devices can facilitate a simple, fast and reliable sample preparation process. A number of groups have since adopted such tools, in some cases to prepare samples for sedimentation-style MAS NMR experiments. Here we argue for a more widespread adoption of their use for routine MAS NMR sample preparation.

On the use of ultracentrifugal devices for routine sample preparation in biomolecular magic-angle-spinning NMR

Energy Technology Data Exchange (ETDEWEB)

Mandal, Abhishek; Boatz, Jennifer C. [University of Pittsburgh School of Medicine, Department of Structural Biology (United States); Wheeler, Travis B. [University of Pittsburgh School of Medicine, Department of Cell Biology (United States); Wel, Patrick C. A. van der, E-mail: vanderwel@pitt.edu [University of Pittsburgh School of Medicine, Department of Structural Biology (United States)

2017-03-15

A number of recent advances in the field of magic-angle-spinning (MAS) solid-state NMR have enabled its application to a range of biological systems of ever increasing complexity. To retain biological relevance, these samples are increasingly studied in a hydrated state. At the same time, experimental feasibility requires the sample preparation process to attain a high sample concentration within the final MAS rotor. We discuss these considerations, and how they have led to a number of different approaches to MAS NMR sample preparation. We describe our experience of how custom-made (or commercially available) ultracentrifugal devices can facilitate a simple, fast and reliable sample preparation process. A number of groups have since adopted such tools, in some cases to prepare samples for sedimentation-style MAS NMR experiments. Here we argue for a more widespread adoption of their use for routine MAS NMR sample preparation.

On-chip sample preparation for complete blood count from raw blood.

Science.gov (United States)

Nguyen, John; Wei, Yuan; Zheng, Yi; Wang, Chen; Sun, Yu

2015-03-21

This paper describes a monolithic microfluidic device capable of on-chip sample preparation for both RBC and WBC measurements from whole blood. For the first time, on-chip sample processing (e.g. dilution, lysis, and filtration) and downstream single cell measurement were fully integrated to enable sample preparation and single cell analysis from whole blood on a single device. The device consists of two parallel sub-systems that perform sample processing and electrical measurements for measuring RBC and WBC parameters. The system provides a modular environment capable of handling solutions of various viscosities by adjusting the length of channels and precisely controlling mixing ratios, and features a new 'offset' filter configuration for increased duration of device operation. RBC concentration, mean corpuscular volume (MCV), cell distribution width, WBC concentration and differential are determined by electrical impedance measurement. Experimental characterization of over 100,000 cells from 10 patient blood samples validated the system's capability for performing on-chip raw blood processing and measurement.

Impact of alternative interventions on changes in generic dispensing rates.

Science.gov (United States)

O'Malley, A James; Frank, Richard G; Kaddis, Atheer; Rothenberg, Barbara M; McNeil, Barbara J

2006-10-01

To evaluate the effectiveness of four alternative interventions (member mailings, advertising campaigns, free generic drug samples to physicians, and physician financial incentives) used by a major health insurer to encourage its members to switch to generic drugs. Using claim-level data from Blue Cross Blue Shield of Michigan, we evaluated the success of four interventions implemented during 2000-2003 designed to increase the use of generic drugs among its members. Around 13 million claims involving seven important classes of drugs were used to assess the effectiveness of the interventions. For each intervention a control group was developed that most closely resembled the corresponding intervention group. Logistic regression models with interaction effects between the treatment group (intervention versus control) and the status of the intervention (active versus not active) were used to evaluate if the interventions had an effect on the generic dispensing rate (GDR). Because the mail order pharmacy was considered more aggressive at converting prescriptions to generics, separate generic purchasing models were fitted to retail and mail order claims. In secondary analyses separate models were also fitted to claims involving a new condition and claims refilled for preexisting conditions. The interventions did not appear to increase the market penetration of generic drugs for either retail or mail order claims, or for claims involving new or preexisting conditions. In addition, we found that the ratio of copayments for brand name to generic drugs had a large positive effect on the GDR. The interventions did not appear to directly influence the GDR. Financial incentives expressed to consumers through benefit designs have a large influence on their switching to generic drugs and on the less-costly mail-order mode of purchase.

Evaluating Site-Specific and Generic Spatial Models of Aboveground Forest Biomass Based on Landsat Time-Series and LiDAR Strip Samples in the Eastern USA

Science.gov (United States)

Ram Deo; Matthew Russell; Grant Domke; Hans-Erik Andersen; Warren Cohen; Christopher Woodall

2017-01-01

Large-area assessment of aboveground tree biomass (AGB) to inform regional or national forest monitoring programs can be efficiently carried out by combining remotely sensed data and field sample measurements through a generic statistical model, in contrast to site-specific models. We integrated forest inventory plot data with spatial predictors from Landsat time-...

Difficulties in preparing a standard sample of uranium metal having traces of nitrogen

International Nuclear Information System (INIS)

Toteja, R.S.D.; Jangida, B.L.; Sundaresan, M.

1991-01-01

Normally in the analysis of uranium for nitrogen, the nitrides are hydrolysed to give NH 3 and that for standardisation purposes to approximate the closest conditions of analysis of ammonia, NH 4 Cl is added to the sample and the recovery is tested. An appropriate method will be to have a standard sample of uranium with known amounts of nitrogen to be used as reference sample. The present work describes the efforts made in the preparation of such a reference sample and a general assessment of such methods available. In present work, known microamounts of nitrogen in an enclosed volume were allowed to react at a temperature of 773 K with a fixed amount of uranium metal of nitrogen content determined chemically. As the reaction of nitrogen with uranium is essentially a surface reaction, a sample had to be homogenised by allowing the nitrided sample to melt at about 1500 K and allow the nitrogen to diffuse through so that the concentration gradient along the profile will disappear. Attempts were made to prepare such samples in the range to 40 to 100 ppm of nitrogen. The density differences of uranium nitride and uranium metal made this diffusion and homogenisation process difficult. The prepared samples were analysed by the micro-kjeldahl's method and the recoveries tested. The equipment used for the preparation of the nitrided samples, for homogenisation and analysis of the results obtained are detailed in the paper together with the assessment of the general methods. (author). 2 refs., 1 fig., 1 tab

Security Policy for a Generic Space Exploration Communication Network Architecture

Science.gov (United States)

Ivancic, William D.; Sheehe, Charles J.; Vaden, Karl R.

2016-01-01

This document is one of three. It describes various security mechanisms and a security policy profile for a generic space-based communication architecture. Two other documents accompany this document- an Operations Concept (OpsCon) and a communication architecture document. The OpsCon should be read first followed by the security policy profile described by this document and then the architecture document. The overall goal is to design a generic space exploration communication network architecture that is affordable, deployable, maintainable, securable, evolvable, reliable, and adaptable. The architecture should also require limited reconfiguration throughout system development and deployment. System deployment includes subsystem development in a factory setting, system integration in a laboratory setting, launch preparation, launch, and deployment and operation in space.

Skin sample preparation by collagenase digestion for diclofenac quantification using LC-MS/MS after topical application.

Science.gov (United States)

Nirogi, Ramakrishna; Padala, Naga Surya Prakash; Boggavarapu, Rajesh Kumar; Kalaikadhiban, Ilayaraja; Ajjala, Devender Reddy; Bhyrapuneni, Gopinadh; Muddana, Nageswara Rao

2016-06-01

Skin is the target site to evaluate the pharmacokinetic parameters of topical applications. Sample preparation is one of the influential steps in the bioanalysis of drugs in the skin. Evaluation of dermatopharmacokinetics at preclinical stage is challenging due to lack of proper sample preparation method. There is a need for an efficient sample preparation procedure for quantification of drugs in the skin using LC-MS/MS. The skin samples treated with collagenase followed by homogenization using a bead beater represents a best-fit method resulting in uniform homogenate for reproducible results. A new approach involving enzymatic treatment and mechanical homogenization techniques were evaluated for efficient sample preparation of skin samples in the bioanalysis.

imFASP: An integrated approach combining in-situ filter-aided sample pretreatment with microwave-assisted protein digestion for fast and efficient proteome sample preparation.

Science.gov (United States)

Zhao, Qun; Fang, Fei; Wu, Ci; Wu, Qi; Liang, Yu; Liang, Zhen; Zhang, Lihua; Zhang, Yukui

2016-03-17

An integrated sample preparation method, termed "imFASP", which combined in-situ filter-aided sample pretreatment and microwave-assisted trypsin digestion, was developed for preparation of microgram and even nanogram amounts of complex protein samples with high efficiency in 1 h. For imFASP method, proteins dissolved in 8 M urea were loaded onto a filter device with molecular weight cut off (MWCO) as 10 kDa, followed by in-situ protein preconcentration, denaturation, reduction, alkylation, and microwave-assisted tryptic digestion. Compared with traditional in-solution sample preparation method, imFASP method generated more protein and peptide identifications (IDs) from preparation of 45 μg Escherichia coli protein sample due to the higher efficiency, and the sample preparation throughput was significantly improved by 14 times (1 h vs. 15 h). More importantly, when the starting amounts of E. coli cell lysate decreased to nanogram level (50-500 ng), the protein and peptide identified by imFASP method were improved at least 30% and 44%, compared with traditional in-solution preparation method, suggesting dramatically higher peptide recovery of imFASP method for trace amounts of complex proteome samples. All these results demonstrate that the imFASP method developed here is of high potential for high efficient and high throughput preparation of trace amounts of complex proteome samples. Copyright © 2016 Elsevier B.V. All rights reserved.

A review of sample preparation and its influence on pH determination in concrete samples

International Nuclear Information System (INIS)

Manso, S.; Aguado, A.

2017-01-01

If we are to monitor the chemical processes in cementitious materials, then pH assays in the pore solutions of cement pastes, mortars, and concretes are of key importance. However, there is no standard method that regulates the sample-preparation method for pH determination. The state-of-the-art of different methods for pH determination in cementitious materials is presented in this paper and the influence of sample preparation in each case. Moreover, an experimental campaign compares three different techniques for pH determination. Its results contribute to establishing a basic criterion to help researchers select the most suitable method, depending on the purpose of the research. A simple tool is described for selecting the easiest and the most economic pH determination method, depending on the objective; especially for researchers and those with limited experience in this field.

Compilation of reports of the Advisory Committee on Reactor Safeguards, 1957-1984. Volume 4. Generic Subjects A-G

International Nuclear Information System (INIS)

1985-04-01

This six-volume compilation contains over 1000 reports prepared by the Advisory Committee on Reactor Safeguards from September 1957 through December 1984. The reports are divided into two groups: Part 1: ACRS Reports on Project Reviews, and Part 2: ACRS Reports on Generic Subjects. Part 1 contains ACRS reports alphabetized by subject name and within project name by chronological order. Part 2 categorizes the reports by the most appropriate generic subject area and within subject area by chronological order. This volume contains generic reports arranged alphabetically from A to G

Compilation of reports of the Advisory Committee on Reactor Safeguards, 1957-1984. Volume 5. Generic Subjects H-R

International Nuclear Information System (INIS)

1985-04-01

This six-volume compilation contains over 1000 reports prepared by the Advisory Committee on Reactor Safeguards from September 1957 through December 1984. The reports are divided into two groups: Part 1: ACRS Reports on Project Reviews, and Part 2: ACRS Reports on Generic Subjects. Part 1 contains ACRS reports alphabetized by project name and within project name by chronological order. Part 2 categorizes the reports by the most appropriate generic subject area and within subject area by chronological order. This volume presents generic subjects arranged alphabetically from H to R

A user-friendly robotic sample preparation program for fully automated biological sample pipetting and dilution to benefit the regulated bioanalysis.

Science.gov (United States)

Jiang, Hao; Ouyang, Zheng; Zeng, Jianing; Yuan, Long; Zheng, Naiyu; Jemal, Mohammed; Arnold, Mark E

2012-06-01

Biological sample dilution is a rate-limiting step in bioanalytical sample preparation when the concentrations of samples are beyond standard curve ranges, especially when multiple dilution factors are needed in an analytical run. We have developed and validated a Microsoft Excel-based robotic sample preparation program (RSPP) that automatically transforms Watson worklist sample information (identification, sequence and dilution factor) to comma-separated value (CSV) files. The Freedom EVO liquid handler software imports and transforms the CSV files to executable worklists (.gwl files), allowing the robot to perform sample dilutions at variable dilution factors. The dynamic dilution range is 1- to 1000-fold and divided into three dilution steps: 1- to 10-, 11- to 100-, and 101- to 1000-fold. The whole process, including pipetting samples, diluting samples, and adding internal standard(s), is accomplished within 1 h for two racks of samples (96 samples/rack). This platform also supports online sample extraction (liquid-liquid extraction, solid-phase extraction, protein precipitation, etc.) using 96 multichannel arms. This fully automated and validated sample dilution and preparation process has been applied to several drug development programs. The results demonstrate that application of the RSPP for fully automated sample processing is efficient and rugged. The RSPP not only saved more than 50% of the time in sample pipetting and dilution but also reduced human errors. The generated bioanalytical data are accurate and precise; therefore, this application can be used in regulated bioanalysis.

Compact low temperature scanning tunneling microscope with in-situ sample preparation capability

Energy Technology Data Exchange (ETDEWEB)

Kim, Jungdae [Department of Physics, The University of Texas, Austin, Texas 78712 (United States); Department of Physics and EHSRC, University of Ulsan, Ulsan 680-749 (Korea, Republic of); Nam, Hyoungdo; Schroeder, Allan; Shih, Chih-Kang, E-mail: shih@physics.utexas.edu [Department of Physics, The University of Texas, Austin, Texas 78712 (United States); Qin, Shengyong [Department of Physics, The University of Texas, Austin, Texas 78712 (United States); Department of Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); ICQD, Hefei National Laboratory for Physical Sciences at the Microscale, University of Science and Technology of China, Hefei, Anhui 230026 (China); Kim, Sang-ui [Department of Physics and EHSRC, University of Ulsan, Ulsan 680-749 (Korea, Republic of); Eom, Daejin [Korea Research Institute of Standards and Science, Daejeon 305-340 (Korea, Republic of)

2015-09-15

We report on the design of a compact low temperature scanning tunneling microscope (STM) having in-situ sample preparation capability. The in-situ sample preparation chamber was designed to be compact allowing quick transfer of samples to the STM stage, which is ideal for preparing temperature sensitive samples such as ultra-thin metal films on semiconductor substrates. Conventional spring suspensions on the STM head often cause mechanical issues. To address this problem, we developed a simple vibration damper consisting of welded metal bellows and rubber pads. In addition, we developed a novel technique to ensure an ultra-high-vacuum (UHV) seal between the copper and stainless steel, which provides excellent reliability for cryostats operating in UHV. The performance of the STM was tested from 2 K to 77 K by using epitaxial thin Pb films on Si. Very high mechanical stability was achieved with clear atomic resolution even when using cryostats operating at 77 K. At 2 K, a clean superconducting gap was observed, and the spectrum was easily fit using the BCS density of states with negligible broadening.

Compact low temperature scanning tunneling microscope with in-situ sample preparation capability.

Science.gov (United States)

Kim, Jungdae; Nam, Hyoungdo; Qin, Shengyong; Kim, Sang-ui; Schroeder, Allan; Eom, Daejin; Shih, Chih-Kang

2015-09-01

We report on the design of a compact low temperature scanning tunneling microscope (STM) having in-situ sample preparation capability. The in-situ sample preparation chamber was designed to be compact allowing quick transfer of samples to the STM stage, which is ideal for preparing temperature sensitive samples such as ultra-thin metal films on semiconductor substrates. Conventional spring suspensions on the STM head often cause mechanical issues. To address this problem, we developed a simple vibration damper consisting of welded metal bellows and rubber pads. In addition, we developed a novel technique to ensure an ultra-high-vacuum (UHV) seal between the copper and stainless steel, which provides excellent reliability for cryostats operating in UHV. The performance of the STM was tested from 2 K to 77 K by using epitaxial thin Pb films on Si. Very high mechanical stability was achieved with clear atomic resolution even when using cryostats operating at 77 K. At 2 K, a clean superconducting gap was observed, and the spectrum was easily fit using the BCS density of states with negligible broadening.

Automated cellular sample preparation using a Centrifuge-on-a-Chip.

Science.gov (United States)

Mach, Albert J; Kim, Jae Hyun; Arshi, Armin; Hur, Soojung Claire; Di Carlo, Dino

2011-09-07

The standard centrifuge is a laboratory instrument widely used by biologists and medical technicians for preparing cell samples. Efforts to automate the operations of concentration, cell separation, and solution exchange that a centrifuge performs in a simpler and smaller platform have had limited success. Here, we present a microfluidic chip that replicates the functions of a centrifuge without moving parts or external forces. The device operates using a purely fluid dynamic phenomenon in which cells selectively enter and are maintained in microscale vortices. Continuous and sequential operation allows enrichment of cancer cells from spiked blood samples at the mL min(-1) scale, followed by fluorescent labeling of intra- and extra-cellular antigens on the cells without the need for manual pipetting and washing steps. A versatile centrifuge-analogue may open opportunities in automated, low-cost and high-throughput sample preparation as an alternative to the standard benchtop centrifuge in standardized clinical diagnostics or resource poor settings.

Exploring community pharmacists' views on generic medicines: a nationwide study from Malaysia.

Science.gov (United States)

Chong, Chee Ping; Hassali, Mohamed Azmi; Bahari, Mohd Baidi; Shafie, Asrul Akmal

2011-02-01

To evaluate the Malaysian community pharmacists' views on generic medicines. A sample of 1419 Malaysian community pharmacies with resident pharmacists. A cross-sectional nationwide survey using a self-completed mailing questionnaire. Pharmacists' views on generic medicines including issues surrounding efficacy, safety, quality and bioequivalence. Responses were received from 219 pharmacies (response rate 15.4%). Only 50.2% of the surveyed pharmacists agreed that all products that are approved as generic equivalents can be considered therapeutically equivalent with the innovator medicines. Around 76% of respondents indicated that generic substitution of narrow therapeutic index medicines is inappropriate. The majority of the pharmacists understood that a generic medicine must contain the same amount of active ingredient (84.5%) and must be in the same dosage form as the innovator brand (71.7%). About 21% of respondents though that generic medicines are of inferior quality compared to innovator medicines. Most of the pharmacists (61.6%) disagreed that generic medicines produce more side-effects than innovator brand. Pharmacists graduated from Malaysian universities, twinning program and overseas universities were not differed significantly in their views on generic medicines. Additionally, the respondents appeared to have difficulty in ascertaining the bioequivalent status of the marketed generic products in Malaysia. The Malaysian pharmacists' have lack of information and/or trust in the generic manufacturing and/or approval system in Malaysia. This issue should be addressed by pharmacy educators and relevant government agencies.

Ultra-High-Throughput Sample Preparation System for Lymphocyte Immunophenotyping Point-of-Care Diagnostics.

Science.gov (United States)

Walsh, David I; Murthy, Shashi K; Russom, Aman

2016-10-01

Point-of-care (POC) microfluidic devices often lack the integration of common sample preparation steps, such as preconcentration, which can limit their utility in the field. In this technology brief, we describe a system that combines the necessary sample preparation methods to perform sample-to-result analysis of large-volume (20 mL) biopsy model samples with staining of captured cells. Our platform combines centrifugal-paper microfluidic filtration and an analysis system to process large, dilute biological samples. Utilizing commercialization-friendly manufacturing methods and materials, yielding a sample throughput of 20 mL/min, and allowing for on-chip staining and imaging bring together a practical, yet powerful approach to microfluidic diagnostics of large, dilute samples. © 2016 Society for Laboratory Automation and Screening.

Highly Reproducible Automated Proteomics Sample Preparation Workflow for Quantitative Mass Spectrometry.

Science.gov (United States)

Fu, Qin; Kowalski, Michael P; Mastali, Mitra; Parker, Sarah J; Sobhani, Kimia; van den Broek, Irene; Hunter, Christie L; Van Eyk, Jennifer E

2018-01-05

Sample preparation for protein quantification by mass spectrometry requires multiple processing steps including denaturation, reduction, alkylation, protease digestion, and peptide cleanup. Scaling these procedures for the analysis of numerous complex biological samples can be tedious and time-consuming, as there are many liquid transfer steps and timed reactions where technical variations can be introduced and propagated. We established an automated sample preparation workflow with a total processing time for 96 samples of 5 h, including a 2 h incubation with trypsin. Peptide cleanup is accomplished by online diversion during the LC/MS/MS analysis. In a selected reaction monitoring (SRM) assay targeting 6 plasma biomarkers and spiked β-galactosidase, mean intraday and interday cyclic voltammograms (CVs) for 5 serum and 5 plasma samples over 5 days were samples repeated on 3 separate days had total CVs below 20%. Similar results were obtained when the workflow was transferred to a second site: 93% of peptides had CVs below 20%. An automated trypsin digestion workflow yields uniformly processed samples in less than 5 h. Reproducible quantification of peptides was observed across replicates, days, instruments, and laboratory sites, demonstrating the broad applicability of this approach.

76 FR 13020 - Agency Information Collection Activities: Comment Request; Generic Clearance for the Collection...

Science.gov (United States)

2011-03-09

... precision requirements or power calculations that justify the proposed sample size, the expected response... Clearance for the Collection of Qualitative Feedback on Agency Service Delivery AGENCY: Department of... Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency...

Development and validation of a tool to assess knowledge and attitudes towards generic medicines among students in Greece: The ATtitude TOwards GENerics (ATTOGEN questionnaire.

Directory of Open Access Journals (Sweden)

Philip J Domeyer

Full Text Available The use of generic medicines is a cost-effective policy, often dictated by fiscal restraints. To our knowledge, no fully validated tool exploring the students' knowledge and attitudes towards generic medicines exists. The aim of our study was to develop and validate a questionnaire exploring the knowledge and attitudes of M.Sc. in Health Care Management students and recent alumni's towards generic drugs in Greece.The development of the questionnaire was a result of literature review and pilot-testing of its preliminary versions to researchers and students. The final version of the questionnaire contains 18 items measuring the respondents' knowledge and attitude towards generic medicines on a 5-point Likert scale. Given the ordinal nature of the data, ordinal alpha and polychoric correlations were computed. The sample was randomly split into two halves. Exploratory factor analysis, performed in the first sample, was used for the creation of multi-item scales. Confirmatory factor analysis and Generalized Linear Latent and Mixed Model analysis (GLLAMM with the use of the rating scale model were used in the second sample to assess goodness of fit. An assessment of internal consistency reliability, test-retest reliability, and construct validity was also performed.Among 1402 persons contacted, 986 persons completed our questionnaire (response rate = 70.3%. Overall Cronbach's alpha was 0.871. The conjoint use of exploratory and confirmatory factor analysis resulted in a six-scale model, which seemed to fit the data well. Five of the six scales, namely trust, drug quality, state audit, fiscal impact and drug substitution were found to be valid and reliable, while the knowledge scale suffered only from low inter-scale correlations and a ceiling effect. However, the subsequent confirmatory factor and GLLAMM analyses indicated a good fit of the model to the data.The ATTOGEN instrument proved to be a reliable and valid tool, suitable for assessing students

Focused-microwave-assisted sample preparation (M8)

International Nuclear Information System (INIS)

Nobrega, J.A.; Santos, D.M.; Trevizan, L.C.; Costa, L.M.; Nogueira, A.R.A.

2002-01-01

Full text: Focused-microwave-assisted sample preparation is a suitable strategy when dealing with high masses of organic samples. However, the final acid concentration of the digestate can difficult routine analytical measurements using spectroscopic techniques. Acids could be evaporated, but this step could be slow even when using microwave-assisted heating and requires a scrubber system for acid vapor collection and neutralization. We are investigating two procedures to decrease the acid concentration of digestates. The first one is based on acid vapor phase digestion of samples contained in PTFE devices' inserted into the microwave flask. The acid solution is heated by absorption of microwave radiation, then the acid vapor partially condenses in the upper part of the reaction flask and it is partially collected in each sample container. Calcium, Fe, Mg, Mn, and Zn were quantitatively recovered in samples of animal and vegetable tissues. Better recoveries were attained when adding a small volume of sodium hypochlorite to the sample. This effect is probably related to the generation of chlorine in the sample container after collecting condensed acid. The second procedure developed is based on the gradual addition of liquid samples to a previously heated acid digestion mixture. This procedure was successfully applied for digestion of milk, fruit juices, and red wine. The main advantage is the possibility of digesting up to four-fold more sample using up to ten-fold lower amounts of concentrated acids. Results obtained using both digestion procedures and measurements by ICP-OES with axial view will be presented. (author)

Ionic liquids: solvents and sorbents in sample preparation.

Science.gov (United States)

Clark, Kevin D; Emaus, Miranda N; Varona, Marcelino; Bowers, Ashley N; Anderson, Jared L

2018-01-01

The applications of ionic liquids (ILs) and IL-derived sorbents are rapidly expanding. By careful selection of the cation and anion components, the physicochemical properties of ILs can be altered to meet the requirements of specific applications. Reports of IL solvents possessing high selectivity for specific analytes are numerous and continue to motivate the development of new IL-based sample preparation methods that are faster, more selective, and environmentally benign compared to conventional organic solvents. The advantages of ILs have also been exploited in solid/polymer formats in which ordinarily nonspecific sorbents are functionalized with IL moieties in order to impart selectivity for an analyte or analyte class. Furthermore, new ILs that incorporate a paramagnetic component into the IL structure, known as magnetic ionic liquids (MILs), have emerged as useful solvents for bioanalytical applications. In this rapidly changing field, this Review focuses on the applications of ILs and IL-based sorbents in sample preparation with a special emphasis on liquid phase extraction techniques using ILs and MILs, IL-based solid-phase extraction, ILs in mass spectrometry, and biological applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development of a sample preparation system for AMS radiocarbon dating at CRICH, Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, Myung-Jin; Lee, Byeong-Cheol; Lim, Eun-Soo [Cultural Research Institute of Chungcheong Heritage, Gongju (Korea, Republic of); Hong, Duk-Geun [Kangwon National University, Chuncheon (Korea, Republic of); Park, Soon-Bal [Chungnam National University, Daejeon (Korea, Republic of); Youn, Min-Young [Seoul National University, Seoul (Korea, Republic of)

2010-01-15

We developed a sample preparation system for radiocarbon dating by using AMS measurement at Cultural Research Institute of Chungcheong Heritage, Korea. From the investigation of the reduction process, the optimum graphitization temperature was chosen as 625 .deg. C. Using Aldrich graphite powder of 0.75 {+-} 0.023 pMC, the background value of our preparation system was controlled at a low level. The robustness against chemical treatment and contamination was also observed from samples of Oxalic acid II and IAEA-C4. The resultant values, 134.04 {+-} 0.99 pMC and 0.38 {+-} 0.043 pMC, were in good agreement with the consensus values. Based on comparison, our conventional ages agreed very well with those of Beta Analytic Co. and SNU-AMS. No memory effect existed in the preparation system. Therefore, we concluded that the sample preparation system was operated in a stable manner and that the basic radiocarbon dating procedures were completely verified.

TCLP Preparation and Analysis of K East Basin Composite Sludge Samples

International Nuclear Information System (INIS)

Silvers, K.L.; Wagner, J.J.; Steele, R.T.

2000-01-01

Sludge samples from the Hanford K East Basin were analyzed by the Toxicity Characterization Leaching Procedure (TCLP) to assist in the appropriate Resource Conservation and Recovery Act (RCIL4) designation of this material. Sludge samples were collected by Fluor Hanford, Inc. using the consolidated sludge sampling system (system that allows collection of a single sample from multiple sample locations). These samples were shipped to the Postirradiation Testing Laboratory (PTL, 327 Building) and then transferred to the Pacific Northwest National Laboratory (PNNL) Radiochemical Processing Laboratory (RPL, 325 Building) for recovery and testing. Two sludge composites were prepared, using the consolidated sludge samples, to represent K East canister sludge (sample KC Can Comp) and K East floor sludge (sample KC Floor Comp). Each composite was extracted in duplicate and analyzed in duplicate following pre-approved(a) TCLP extraction and analyses procedures. In addition, these samples and duplicates were analyzed for total RCRA metals (via acid digestion preparation). The work was conducted in accordance with the requirements of the Hanford Analytical Quality Assurance Requirements Document (HASQARD). A PNNL Quality Assurance Program compliant with J HASQARD was implemented for this effort. The results from the TCLP analyses showed that all RCRA metal concentrations were less than the TCLP limits for both the canister and floor composite samples and their respective duplicates

Capacitive deionization on-chip as a method for microfluidic sample preparation

NARCIS (Netherlands)

Roelofs, Susan Helena; Kim, Bumjoo; Eijkel, Jan C.T.; Han, Jongyoon; van den Berg, Albert; Odijk, Mathieu

2015-01-01

Desalination as a sample preparation step is essential for noise reduction and reproducibility of mass spectrometry measurements. A specific example is the analysis of proteins for medical research and clinical applications. Salts and buffers that are present in samples need to be removed before

Examining Generic Competitive Strategy Types in U.S. and European Markets

OpenAIRE

Susan P Douglas; Dong Kee Rhee

1989-01-01

Identification of generic competitive strategy types has recently attracted considerable attention. Most of this research has, however, focused on competitive strategy of U.S. businesses in their domestic market. The present study extends these findings to markets outside the United States, and more specifically Europe, based on a sample of industrial businesses drawn from the PIMS database. Similar dimensions underlying competitive strategy, and similar generic types are found among business...

LC-MS analysis of the plasma metabolome–a novel sample preparation strategy

DEFF Research Database (Denmark)

Skov, Kasper; Hadrup, Niels; Smedsgaard, Jørn

2015-01-01

Blood plasma is a well-known body fluid often analyzed in studies on the effects of toxic compounds as physiological or chemical induced changes in the mammalian body are reflected in the plasma metabolome. Sample preparation prior to LC-MS based analysis of the plasma metabolome is a challenge...... as plasma contains compounds with very different properties. Besides, proteins, which usually are precipitated with organic solvent, phospholipids, are known to cause ion suppression in electrospray mass spectrometry. We have compared two different sample preparation techniques prior to LC-qTOF analysis...... of plasma samples: The first is protein precipitation; the second is protein precipitation followed by solid phase extraction with sub-fractionation into three sub-samples; a phospholipid, a lipid and a polar sub-fraction. Molecular feature extraction of the data files from LC-qTOF analysis of the samples...

76 FR 37825 - Agency Information Collection Activities; Generic Clearance for the Collection of Qualitative...

Science.gov (United States)

2011-06-28

... requirements or power calculations that justify the proposed sample size, the expected response rate, methods... Activities; Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery AGENCY: U...): ``Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery '' to OMB for...

[Sample preparation methods for chromatographic analysis of organic components in atmospheric particulate matter].

Science.gov (United States)

Hao, Liang; Wu, Dapeng; Guan, Yafeng

2014-09-01

The determination of organic composition in atmospheric particulate matter (PM) is of great importance in understanding how PM affects human health, environment, climate, and ecosystem. Organic components are also the scientific basis for emission source tracking, PM regulation and risk management. Therefore, the molecular characterization of the organic fraction of PM has become one of the priority research issues in the field of environmental analysis. Due to the extreme complexity of PM samples, chromatographic methods have been the chief selection. The common procedure for the analysis of organic components in PM includes several steps: sample collection on the fiber filters, sample preparation (transform the sample into a form suitable for chromatographic analysis), analysis by chromatographic methods. Among these steps, the sample preparation methods will largely determine the throughput and the data quality. Solvent extraction methods followed by sample pretreatment (e. g. pre-separation, derivatization, pre-concentration) have long been used for PM sample analysis, and thermal desorption methods have also mainly focused on the non-polar organic component analysis in PM. In this paper, the sample preparation methods prior to chromatographic analysis of organic components in PM are reviewed comprehensively, and the corresponding merits and limitations of each method are also briefly discussed.

A review of sample preparation and its influence on pH determination in concrete samples

Directory of Open Access Journals (Sweden)

S. Manso

2017-01-01

Full Text Available If we are to monitor the chemical processes in cementitious materials, then pH assays in the pore solutions of cement pastes, mortars, and concretes are of key importance. However, there is no standard method that regulates the sample-preparation method for pH determination. The state-of-the-art of different methods for pH determination in cementitious materials is presented in this paper and the influence of sample preparation in each case. Moreover, an experimental campaign compares three different techniques for pH determination. Its results contribute to establishing a basic criterion to help researchers select the most suitable method, depending on the purpose of the research. A simple tool is described for selecting the easiest and the most economic pH determination method, depending on the objective; especially for researchers and those with limited experience in this field.

A developed wedge fixtures assisted high precision TEM samples pre-thinning method: Towards the batch lamella preparation

Directory of Open Access Journals (Sweden)

Dandan Wang

2017-04-01

Full Text Available Ion milling, wedge cutting or polishing, and focused ion beam (FIB milling are widely-used techniques for the transmission electron microscope (TEM sample preparation. Especially, the FIB milling provides a site-specific analysis, deposition, and ablation of materials in the micrometer and nanometer scale. However, the cost of FIB tools has been always a significant concern. Since it is inevitable to use the FIB technique, the improvement of efficiency is a key point. Traditional TEM sample preparation with FIB was routinely implemented on a single sample each time. Aiming at cost efficiency, a new pre-thinning technique for batch sample preparation was developed in this paper. The present proposal combines the sample preparation techniques with multi-samples thinning, cross-section scanning electron microscopy (SEM, wedge cutting, FIB and other sample pre-thinning techniques. The new pre-thinning technique is to prepare an edge TEM sample on a grinding and polishing fixture with a slant surface. The thickness of the wedges sample can be measured to 1∼2 μm under optical microscope. Therefore, this fixture is superior to the traditional optical method of estimating the membrane thickness. Moreover, by utilizing a multi-sample holding fixture, more samples can be pre-thinned simultaneously, which significantly improved the productivity of TEM sample preparation.

Optimizing Generic Functions

NARCIS (Netherlands)

Alimarine, A.; Smetsers, J.E.W.

2004-01-01

Generic functions are defined by induction on the structural representation of types. As a consequence, by defining just a single generic operation, one acquires this operation over any particular type. An instance on a specific type is generated by interpretation of the type's structure. A direct

Automated injection of a radioactive sample for preparative HPLC with feedback control

International Nuclear Information System (INIS)

Iwata, Ren; Yamazaki, Shigeki

1990-01-01

The injection of a radioactive reaction mixture into a preparative HPLC column has been automated with computer control for rapid purification of routinely prepared positron emitting radiopharmaceuticals. Using pneumatic valves, a motor-driven pump and a liquid level sensor, two intelligent injection methods for the automation were compared with regard to efficient and rapid sample loading into a 2 mL loop of the 6-way valve. One, a precise but rather slow method, was demonstrated to be suitable for purification of 18 F-radiopharmaceuticals, while the other, due to its rapid operation, was more suitable for 11 C-radiopharmaceuticals. A sample volume of approx 0.5 mL can be injected onto a preparative HPLC column with over 90% efficiency with the present automated system. (author)

Sample preparation and fractionation for proteome analysis and cancer biomarker discovery by mass spectrometry.

Science.gov (United States)

Ahmed, Farid E

2009-03-01

Sample preparation and fractionation technologies are one of the most crucial processes in proteomic analysis and biomarker discovery in solubilized samples. Chromatographic or electrophoretic proteomic technologies are also available for separation of cellular protein components. There are, however, considerable limitations in currently available proteomic technologies as none of them allows for the analysis of the entire proteome in a simple step because of the large number of peptides, and because of the wide concentration dynamic range of the proteome in clinical blood samples. The results of any undertaken experiment depend on the condition of the starting material. Therefore, proper experimental design and pertinent sample preparation is essential to obtain meaningful results, particularly in comparative clinical proteomics in which one is looking for minor differences between experimental (diseased) and control (nondiseased) samples. This review discusses problems associated with general and specialized strategies of sample preparation and fractionation, dealing with samples that are solution or suspension, in a frozen tissue state, or formalin-preserved tissue archival samples, and illustrates how sample processing might influence detection with mass spectrometric techniques. Strategies that dramatically improve the potential for cancer biomarker discovery in minimally invasive, blood-collected human samples are also presented.

Compilation of reports of the Advisory Committee on Reactor Safeguards, 1957-1984. Volume 6. Generic Subjects R-Z, Appendices

International Nuclear Information System (INIS)

1985-04-01

This six-volume compilation contains over 1000 reports prepared by the Advisory Committee on Reactor Safeguards from September 1957 through December 1984. The reports are divided into two groups: Part 1: ACRS Reports on Project Reviews, and Part 2: ACRS Reports on Generic Subjects. Part 1 contains ACRS reports alphabetized by project name and within project name by chronological order. Part 2 categorizes the reports by the most appropriate generic subject area and within subject area by chronological order. This volume contains the generic subjects with an alphabetical listing from R to Z

Electrodeposition as an alternate method for preparation of environmental samples for iodide by AMS

Energy Technology Data Exchange (ETDEWEB)

Adamic, M.L., E-mail: Mary.Adamic@inl.gov [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83402 (United States); Lister, T.E.; Dufek, E.J.; Jenson, D.D.; Olson, J.E. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83402 (United States); Vockenhuber, C. [Laboratory of Ion Beam Physics, ETH Zurich, Otto-Stern-Weg 5, 8093 Zurich (Switzerland); Watrous, M.G. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83402 (United States)

2015-10-15

This paper presents an evaluation of an alternate method for preparing environmental samples for {sup 129}I analysis by accelerator mass spectrometry (AMS) at Idaho National Laboratory. The optimal sample preparation method is characterized by ease of preparation, capability of processing very small quantities of iodide, and ease of loading into a cathode. Electrodeposition of iodide on a silver wire was evaluated using these criteria. This study indicates that the electrochemically-formed silver iodide deposits produce ion currents similar to those from precipitated silver iodide for the same sample mass. Precipitated silver iodide samples are usually mixed with niobium or silver powder prior to loading in a cathode. Using electrodeposition, the silver is already mixed with the sample and can simply be picked up with tweezers, placed in the sample die, and pressed into a cathode. The major advantage of this method is that the silver wire/electrodeposited silver iodide is much easier to load into a cathode.

Electrodeposition as an alternate method for preparation of environmental samples for iodide by AMS

International Nuclear Information System (INIS)

Adamic, M.L.; Lister, T.E.; Dufek, E.J.; Jenson, D.D.; Olson, J.E.; Vockenhuber, C.; Watrous, M.G.

2015-01-01

This paper presents an evaluation of an alternate method for preparing environmental samples for "1"2"9I analysis by accelerator mass spectrometry (AMS) at Idaho National Laboratory. The optimal sample preparation method is characterized by ease of preparation, capability of processing very small quantities of iodide, and ease of loading into a cathode. Electrodeposition of iodide on a silver wire was evaluated using these criteria. This study indicates that the electrochemically-formed silver iodide deposits produce ion currents similar to those from precipitated silver iodide for the same sample mass. Precipitated silver iodide samples are usually mixed with niobium or silver powder prior to loading in a cathode. Using electrodeposition, the silver is already mixed with the sample and can simply be picked up with tweezers, placed in the sample die, and pressed into a cathode. The major advantage of this method is that the silver wire/electrodeposited silver iodide is much easier to load into a cathode.

A high-throughput sample preparation method for cellular proteomics using 96-well filter plates.

Science.gov (United States)

Switzar, Linda; van Angeren, Jordy; Pinkse, Martijn; Kool, Jeroen; Niessen, Wilfried M A

2013-10-01

A high-throughput sample preparation protocol based on the use of 96-well molecular weight cutoff (MWCO) filter plates was developed for shotgun proteomics of cell lysates. All sample preparation steps, including cell lysis, buffer exchange, protein denaturation, reduction, alkylation and proteolytic digestion are performed in a 96-well plate format, making the platform extremely well suited for processing large numbers of samples and directly compatible with functional assays for cellular proteomics. In addition, the usage of a single plate for all sample preparation steps following cell lysis reduces potential samples losses and allows for automation. The MWCO filter also enables sample concentration, thereby increasing the overall sensitivity, and implementation of washing steps involving organic solvents, for example, to remove cell membranes constituents. The optimized protocol allowed for higher throughput with improved sensitivity in terms of the number of identified cellular proteins when compared to an established protocol employing gel-filtration columns. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Review of sample preparation techniques for the analysis of pesticide residues in soil.

Science.gov (United States)

Tadeo, José L; Pérez, Rosa Ana; Albero, Beatriz; García-Valcárcel, Ana I; Sánchez-Brunete, Consuelo

2012-01-01

This paper reviews the sample preparation techniques used for the analysis of pesticides in soil. The present status and recent advances made during the last 5 years in these methods are discussed. The analysis of pesticide residues in soil requires the extraction of analytes from this matrix, followed by a cleanup procedure, when necessary, prior to their instrumental determination. The optimization of sample preparation is a very important part of the method development that can reduce the analysis time, the amount of solvent, and the size of samples. This review considers all aspects of sample preparation, including extraction and cleanup. Classical extraction techniques, such as shaking, Soxhlet, and ultrasonic-assisted extraction, and modern techniques like pressurized liquid extraction, microwave-assisted extraction, solid-phase microextraction and QuEChERS (Quick, Easy, Cheap, Effective, Rugged, and Safe) are reviewed. The different cleanup strategies applied for the purification of soil extracts are also discussed. In addition, the application of these techniques to environmental studies is considered.

Ergonomic analysis of radiopharmaceuticals samples preparation process

International Nuclear Information System (INIS)

Gomes, Luciene Betzler C.; Santos, Isaac Luquetti dos; Fonseca, Antonio Carlos C. da; Pellini, Marcos Pinto; Rebelo, Ana Maria

2005-01-01

The doses of radioisotopes to be administrated in patients for diagnostic effect or therapy are prepared in the radiopharmacological sector. The preparation process adopts techniques that are aimed to reduce the exposition time of the professionals and the absorption of excessive doses for patients. The ergonomic analysis of this process contributes in the prevention of occupational illnesses and to prevent risks of accidents during the routines, providing welfare and security to the involved users and conferring to the process an adequate working standard. In this context it is perceived relevance of studies that deal with the analysis of factors that point with respect to the solution of problems and for establishing proposals that minimize risks in the exercise of the activities. Through a methodology that considers the application of the concepts of Ergonomics, it is searched the improvement of the effectiveness or the quality and reduction of the difficulties lived for the workers. The work prescribed, established through norms and procedures codified will be faced with the work effectively carried through, the real work, shaped to break the correct appreciation, with focus in the activities. This work has as objective to argue an ergonomic analysis of samples preparation process of radioisotopes in the Setor de Radiofarmacia do Hospital Universitario Clementino Fraga Filho da Universidade Federal do Rio de Janeiro (UFRJ). (author)

Improved sample preparation and counting techniques for enhanced tritium measurement sensitivity

Science.gov (United States)

Moran, J.; Aalseth, C.; Bailey, V. L.; Mace, E. K.; Overman, C.; Seifert, A.; Wilcox Freeburg, E. D.

2015-12-01

Tritium (T) measurements offer insight to a wealth of environmental applications including hydrologic tracking, discerning ocean circulation patterns, and aging ice formations. However, the relatively short half-life of T (12.3 years) limits its effective age dating range. Compounding this limitation is the decrease in atmospheric T content by over two orders of magnitude (from 1000-2000 TU in 1962 to testing in the 1960's. We are developing sample preparation methods coupled to direct counting of T via ultra-low background proportional counters which, when combined, offer improved T measurement sensitivity (~4.5 mmoles of H2 equivalent) and will help expand the application of T age dating to smaller sample sizes linked to persistent environmental questions despite the limitations above. For instance, this approach can be used to T date ~ 2.2 mmoles of CH4 collected from sample-limited systems including microbial communities, soils, or subsurface aquifers and can be combined with radiocarbon dating to distinguish the methane's formation age from C age in a system. This approach can also expand investigations into soil organic C where the improved sensitivity will permit resolution of soil C into more descriptive fractions and provide direct assessments of the stability of specific classes of organic matter in soils environments. We are employing a multiple step sample preparation system whereby organic samples are first combusted with resulting CO2 and H2O being used as a feedstock to synthesize CH4. This CH4 is mixed with Ar and loaded directly into an ultra-low background proportional counter for measurement of T β decay in a shallow underground laboratory. Analysis of water samples requires only the addition of geologic CO2 feedstock with the sample for methane synthesis. The chemical nature of the preparation techniques enable high sample throughput with only the final measurement requiring T decay with total sample analysis time ranging from 2 -5 weeks

Preparation and application of radioactive soil samples for intercomparison

International Nuclear Information System (INIS)

Gao Zequan; Li Zhou; Li Pengxiang; Wang Ruijun; Ren Xiaona

2014-01-01

This article summarized the preparation process and intercomparison results of the simulated environmental radioactive soil samples. The components of the matrix were: SiO 2 , Al 2 O 3 , Fe 2 O 3 , MgO, CaO, NaCl, KCl and TiO 2 . All of the components were milled, oven-dried, sieved and then blended together. The homogeneity test was according to GB 15000. 5-1994, and no significant differences were observed. The 3 H analysis soils were spiked natural soils with the moisture content of 15%. Eight laboratories attended this intercomparison. The results proves that the preparation of the simulated soils were suitable for the inter-laboratories comparison. (authors)

Preparation of rock samples for measurement of the thermal neutron macroscopic absorption cross-section

International Nuclear Information System (INIS)

Czubek, J.A.; Burda, J.; Drozdowicz, K.; Igielski, A.; Kowalik, W.; Krynicka-Drozdowicz, E.; Woznicka, U.

1986-03-01

Preparation of rock samples for the measurement of the thermal neutron macroscopic absorption cross-section in small cylindrical two-region systems by a pulsed technique is presented. Requirements which should be fulfilled during the preparation of the samples due to physical assumptions of the method are given. A cylindrical vessel is filled with crushed rock and saturated with a medium strongly absorbing thermal neutrons. Water solutions of boric acid of well-known macroscopic absorption cross-section are used. Mass contributions of the components in the sample are specified. This is necessary for the calculation of the thermal neutron macroscopic absorption cross-section of the rock matrix. The conditions necessary for assuring the required accuracy of the measurement are given and the detailed procedure of preparation of the rock sample is described. (author)

Should the mass of a nanoferrite sample prepared by autocombustion method be considered as a realistic preparation parameter?

Energy Technology Data Exchange (ETDEWEB)

Wahba, Adel Maher, E-mail: adel.mousa@f-eng.tanta.edu.eg [Department of Engineering Physics and Mathematics, Faculty of Engineering, Tanta University (Egypt); Mohamed, Mohamed Bakr [Ain shams University, Faculty of Science, Physics Department, Cairo (Egypt)

2017-02-15

Detectable variations in structural, elastic and magnetic properties have been reported depending on the mass of the cobalt nanoferrite sample prepared by citrate autocombustion method. Heat released during the autocombustion process and its duration are directly proportional to the mass to be prepared, and is thus expected to affect both the crystallite size and the cation distribution giving rise to the reported variations in microstrain, magnetization, and coercivity. Formation of a pure spinel phase has been validated using X-ray diffraction patterns (XRD) and Fourier-transform infrared (FTIR) spectra. Crystallite sizes obtained from Williamson-Hall (W-H) method range from 28–87 nm, being further supported by images of high-resolution transmission electron microscope (HRTEM). Saturation magnetization and coercivity deduced from M-H hysteresis loops show a clear correlation with the cation distribution, which was proposed on the basis of experimentally obtained data of XRD, VSM, and IR. Elastic parameters have been estimated using the cation distribution and FTIR data, with a resulting trend quite opposite to that of the lattice parameter. - Highlights: • Samples with different masses of CoFe{sub 2}O{sub 4} were prepared by autocombustion method. • XRD and IR data confirmed a pure spinel cubic structure for all samples. • Structural and magnetic properties show detectable changes with the mass prepared. • Cation distribution was suggested from experimental data of XRD, IR, and M-H loops.

Generic Example Proving Criteria for All

Science.gov (United States)

Yopp, David; Ely, Rob; Johnson­-Leung, Jennifer

2015-01-01

We review literature that discusses generic example proving and highlight ambiguities that pervade our research community's discourse about generic example arguments. We distinguish between pedagogical advice for choosing good examples that can serve as generic examples when teaching and advice for developing generic example arguments. We provide…

Experiences from Refurbishment of Metallography Hot Cells and Application of a New Preparation Concept for Materialography Samples

International Nuclear Information System (INIS)

Oberlander, B. C.; Espeland, M.; Solum, N. O.

2001-01-01

After more than 30 years of operation the lead shielded metallography hot cells needed a basic renewal and modernisation not least of the specimen preparation equipment. Preparation in hot cells of radioactive samples for metallography and ceramography is challenging and time consuming. It demands a special design and quality of all in-cell equipment and skill and patience from the operator. Essentials in the preparation process are: simplicity and reliability of the machines, and a good quality, reproducibility and efficiency in performance. Desirable is process automation, flexibility and an alara amounto of radioactive waste produced per sample prepared. State of the art preparation equipment for materialography seems to meet most of the demands, however, it cannot be used in hot cells without modifications. Therefore. IFE and Struers in Copenhagen modified a standard model of a Strues precision cutting machine and a microprocessor controlled grinding and polishing machine for Hot Cell application. Hot cell utilisation of the microcomputer controlled grinding and polishing machine and the existing automatic dosing equipment made the task of preparing radioactive samples more attractive. The new grinding and polishing system for hot cells provides good sample preparation quality and reproductibility at reduced preparation time and reduced amount of contaminated waste produced per sample prepared. the sample materials examined were irradiated cladding materials and fuels

Generic and biosimilar medicines: quid?

Directory of Open Access Journals (Sweden)

Steven Simoens

2012-12-01

Full Text Available Once intellectual property protection, data and marketing exclusivity of reference medicines have expired, generic medicines and biosimilar medicines can enter the off-patent market. This market entry is conditional on the approval of marketing authorization, pricing and reimbursement. Given that there tends to be confusion surrounding generic and biosimilar medicines, this Editorial introduces basic concepts related to generic and biosimilar medicines and presents the different studies and articles included in this supplement dedicated to generic and biosimilar medicines.

Radiocarbon accelerator mass spectrometry (AMS) sample preparation laboratory in Brazil

International Nuclear Information System (INIS)

Macario, Kita D.; Gomes, Paulo R. S.; Anjos, Roberto M. dos; Linares, Roberto; Queiroz, Eduardo; Oliveira, Fabiana M. de; Cardozo, Laio; Carvalho, Carla R.A.

2011-01-01

Full text: For decades Accelerator Mass Spectrometry has been widely used for radiocarbon measurements all over the world with application in several fields of science from archaeology to geosciences. This technique provides ultrasensitive analysis of reduced size samples or even specific compounds since sample atoms are accelerated to high energies and measured using nuclear particle detectors. Sample preparation is extremely important for accurate radiocarbon measurement and includes chemical pre-treatment to remove all possible contaminants. For beam extraction in the accelerator ion source, samples are usually converted to graphite. In this work we report a new radiocarbon sample preparation facility installed at the Physics Institute of Universidade Federal Fluminense (UFF), in Brazil. At the Nuclear Chronology Laboratory (LACRON) samples are chemically treated and converted to carbon dioxide by hydrolysis or combustion. A stainless steel based vacuum line was constructed for carbon dioxide separation and graphitization is performed in sealed quartz tubes in a muffle oven. Successful graphite production is important to provide stable beam currents and to minimize isotopic fractionation. Performance tests for graphite production are currently under way and isotopic analysis will soon be possible with the acquisition of a Single Stage AMS System by our group. The Single Stage Accelerator produced by National Electrostatic Corporation is a 250 kV air insulated accelerator especially constructed to measure the amount of 14 C in small modern graphite samples to a precision of 0.3 % or better. With the installation of such equipment in the first half of 2012, UFF will be ready to perform the 14C -AMS technique. (author)

TruSeq Stranded mRNA and Total RNA Sample Preparation Kits

Science.gov (United States)

Total RNA-Seq enabled by ribosomal RNA (rRNA) reduction is compatible with formalin-fixed paraffin embedded (FFPE) samples, which contain potentially critical biological information. The family of TruSeq Stranded Total RNA sample preparation kits provides a unique combination of unmatched data quality for both mRNA and whole-transcriptome analyses, robust interrogation of both standard and low-quality samples and workflows compatible with a wide range of study designs.

Preparation and characterisation of magnetic nanostructured samples for inelastic neutron scattering experiments

Energy Technology Data Exchange (ETDEWEB)

Kreuzpaintner, Wolfgang

2010-06-22

Recent advances in thin-film structuring techniques have generated significant interest in the dynamics of spin waves in magnetic nanostructures and the possible use of inelastic neutron scattering (INS) for their investigation. This thesis describes the design and implementation, at GKSS Research Centre, of equipment for preparation of large and laterally submicron and nanometre structured magnetic samples for such future INS experiments. After a brief resume on spin waves in nanostructures, the development work on new purpose-designed equipment, including high vacuum (HV) argon ion beam milling and ultra high vacuum (UHV) e-beam evaporation setups, is described. Ni nanodot as well as Ni and novel Gd nanowire samples were prepared using combinations of sputter deposition, laser interference lithography, argon ion beam milling, e-beam evaporation and self organisation techniques. With reference to sample preparation, epitaxial growth studies for Ni on Si(100) substrate were performed, resulting in the development of a new deposition process, which by thermal tuning allows for the direct epitaxial growth of Ni on Si with unprecedented crystalline quality. The results of various characterisation experiments on the prepared nanostructured samples, including Scanning Electron Microscopy (SEM), microprobe analysis, Atomic and Magnetic Force Microscopy (AFM/MFM), Vibrating Sample Magnetometry (VSM), X-ray Diffraction (XRD) and Reflectivity (XRR), unpolarised and Polarised Neutron Scattering (PNR) and off-specular scattering by X-rays and neutrons using rocking scans and Time-Of-Flight Grazing Incidence Small Angle Neutron Scattering (TOF-GISANS), together with various analysis procedures such as Distorted-Wave Born Approximation (DWBA), are reported. The analysis of a Gd nanowire sample by TOF-GISANS led to a novel evaluation technique which in comparison with single wavelength methods allows portions of reciprocal space to be scanned without changing the angle of

Preparation and characterisation of magnetic nanostructured samples for inelastic neutron scattering experiments

International Nuclear Information System (INIS)

Kreuzpaintner, Wolfgang

2010-01-01

Recent advances in thin-film structuring techniques have generated significant interest in the dynamics of spin waves in magnetic nanostructures and the possible use of inelastic neutron scattering (INS) for their investigation. This thesis describes the design and implementation, at GKSS Research Centre, of equipment for preparation of large and laterally submicron and nanometre structured magnetic samples for such future INS experiments. After a brief resume on spin waves in nanostructures, the development work on new purpose-designed equipment, including high vacuum (HV) argon ion beam milling and ultra high vacuum (UHV) e-beam evaporation setups, is described. Ni nanodot as well as Ni and novel Gd nanowire samples were prepared using combinations of sputter deposition, laser interference lithography, argon ion beam milling, e-beam evaporation and self organisation techniques. With reference to sample preparation, epitaxial growth studies for Ni on Si(100) substrate were performed, resulting in the development of a new deposition process, which by thermal tuning allows for the direct epitaxial growth of Ni on Si with unprecedented crystalline quality. The results of various characterisation experiments on the prepared nanostructured samples, including Scanning Electron Microscopy (SEM), microprobe analysis, Atomic and Magnetic Force Microscopy (AFM/MFM), Vibrating Sample Magnetometry (VSM), X-ray Diffraction (XRD) and Reflectivity (XRR), unpolarised and Polarised Neutron Scattering (PNR) and off-specular scattering by X-rays and neutrons using rocking scans and Time-Of-Flight Grazing Incidence Small Angle Neutron Scattering (TOF-GISANS), together with various analysis procedures such as Distorted-Wave Born Approximation (DWBA), are reported. The analysis of a Gd nanowire sample by TOF-GISANS led to a novel evaluation technique which in comparison with single wavelength methods allows portions of reciprocal space to be scanned without changing the angle of

Infrared biospectroscopy for a fast qualitative evaluation of sample preparation in metabolomics.

Science.gov (United States)

Kuligowski, Julia; Pérez-Guaita, David; Escobar, Javier; Lliso, Isabel; de la Guardia, Miguel; Lendl, Bernhard; Vento, Máximo; Quintás, Guillermo

2014-09-01

Liquid chromatography-mass spectrometry (LC-MS) has been increasingly used in biomedicine to study the dynamic metabolomic responses of biological systems under different physiological or pathological conditions. To obtain an integrated snapshot of the system, metabolomic methods in biomedicine typically analyze biofluids (e.g. plasma) that require clean-up before being injected into LC-MS systems. However, high resolution LC-MS is costly in terms of resources required for sample and data analysis and care must be taken to prevent chemical (e.g. ion suppression) or statistical artifacts. Because of that, the effect of sample preparation on the metabolomic profile during metabolomic method development is often overlooked. This work combines an Attenuated Total Reflectance-Fourier transform infrared (ATR-FTIR) and a multivariate exploratory data analysis for a cost-effective qualitative evaluation of major changes in sample composition during sample preparation. ATR-FTIR and LC-time of flight mass spectrometry (TOFMS) data from the analysis of a set of plasma samples precipitated using acetonitrile, methanol and acetone performed in parallel were used as a model example. Biochemical information obtained from the analysis of the ATR-FTIR and LC-TOFMS data was thoroughly compared to evaluate the strengths and shortcomings of FTIR biospectroscopy for assessing sample preparation in metabolomics studies. Results obtained show the feasibility of ATR-FTIR for the evaluation of major trends in the plasma composition changes among different sample pretreatments, providing information in terms of e.g., amino acids, proteins, lipids and carbohydrates overall contents comparable to those found by LC-TOFMS. Copyright © 2014 Elsevier B.V. All rights reserved.

Highly oriented Bi-system bulk sample prepared by a decomposition-crystallization process

International Nuclear Information System (INIS)

Xi Zhengping; Zhou Lian; Ji Chunlin

1992-01-01

A decomposition-crystallization method, preparing highly oriented Bi-system bulk sample is reported. The effects of processing parameter, decomposition temperature, cooling rate and post-treatment condition on texture and superconductivity are investigated. The method has successfully prepared highly textured Bi-system bulk samples. High temperature annealing does not destroy the growing texture, but the cooling rate has some effect on texture and superconductivity. Annealing in N 2 /O 2 atmosphere can improve superconductivity of the textured sample. The study on the superconductivity of the Bi(Pb)-Sr-Ca-Cu-O bulk material has been reported in numerous papers. The research on J c concentrates on the tape containing the 2223 phase, with very few studies on the J c of bulk sample. The reason for the lack of studies is that the change of superconducting phases at high temperatures has not been known. The authors have reported that the 2212 phase incongruently melted at about 875 degrees C and proceeded to orient the c-axis perpendicular to the surface in the process of crystallization of the 2212 phase. Based on that result, a decomposition-crystallization method was proposed to prepare highly oriented Bi-system bulk sample. In this paper, the process is described in detail and the effects of processing parameters on texture and superconductivity are reported

X-ray diffraction without sample preparation: Proof-of-principle experiments

International Nuclear Information System (INIS)

Hansford, Graeme M.

2013-01-01

The properties of a novel X-ray diffraction (XRD) technique having very low sensitivity to the sample morphology were previously elucidated through theoretical considerations and model simulations (Hansford, 2011). This technique opens up the possibility of mineralogical analysis by XRD without sample preparation. Here, the results of proof-of-principle experimental tests are presented. Two sets of experiments were performed using a vacuum chamber equipped with an X-ray tube source, sample holder and charge-coupled detector. Firstly, a pressed-powder pellet of α-quartz was placed in three different positions relative to the X-ray source and detector. The changes in position represent gross sample movements which would be inconceivable in conventional XRD analysis. The resulting back-reflection energy-dispersive spectra show a very high degree of correspondence other than an overall intensity factor dependent on the distance between the sample and detector. Secondly, the back-reflection spectrum of an unprepared limestone hand specimen, having mm-scale surface morphology, was compared to the spectrum of a calcite pressed-powder pellet. The correspondence of the diffraction peaks in the spectra demonstrate that the limestone is comprised dominantly of calcite. In both cases, the claims of the earlier paper are fully supported by the results of these experimental tests. -- Highlights: • Proof-of-principle tests of a novel X-ray diffraction (XRD) method were conducted. • Very low sensitivity to sample position and orientation was demonstrated. • Insensitivity to sample morphology is inferred. • A simple analysis of an unprepared limestone hand specimen was performed. • This technique enables mineralogical analysis by XRD without sample preparation

pH adjustment of human blood plasma prior to bioanalytical sample preparation

NARCIS (Netherlands)

Hendriks, G.; Uges, D. R. A.; Franke, J. P.

2008-01-01

pH adjustment in bioanalytical sample preparation concerning ionisable compounds is one of the most common sample treatments. This is often done by mixing an aliquot of the sample with a proper buffer adjusted to the proposed pH. The pH of the resulting mixture however, does not necessarily have to

The role of graphene-based sorbents in modern sample preparation techniques.

Science.gov (United States)

de Toffoli, Ana Lúcia; Maciel, Edvaldo Vasconcelos Soares; Fumes, Bruno Henrique; Lanças, Fernando Mauro

2018-01-01

The application of graphene-based sorbents in sample preparation techniques has increased significantly since 2011. These materials have good physicochemical properties to be used as sorbent and have shown excellent results in different sample preparation techniques. Graphene and its precursor graphene oxide have been considered to be good candidates to improve the extraction and concentration of different classes of target compounds (e.g., parabens, polycyclic aromatic hydrocarbon, pyrethroids, triazines, and so on) present in complex matrices. Its applications have been employed during the analysis of different matrices (e.g., environmental, biological and food). In this review, we highlight the most important characteristics of graphene-based material, their properties, synthesis routes, and the most important applications in both off-line and on-line sample preparation techniques. The discussion of the off-line approaches includes methods derived from conventional solid-phase extraction focusing on the miniaturized magnetic and dispersive modes. The modes of microextraction techniques called stir bar sorptive extraction, solid phase microextraction, and microextraction by packed sorbent are discussed. The on-line approaches focus on the use of graphene-based material mainly in on-line solid phase extraction, its variation called in-tube solid-phase microextraction, and on-line microdialysis systems. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Factors influencing the preference for purchasing generic drugs in a Southern Brazilian city.

Science.gov (United States)

Guttier, Marília Cruz; Silveira, Marysabel Pinto Telis; Luiza, Vera Lucia; Bertoldi, Andréa Dâmaso

2017-06-26

The objective of this study is to identify factors associated with the preference for purchasing generic drugs in a medium-sized municipality in Southern Brazil. We have analyzed data from a population-based cross-sectional study conducted in 2012 with a sample of 2,856 adults (≥ 20 years old). The preference for purchasing generic drugs was the main outcome. The explanatory variables were the demographic and socioeconomic variables. Statistical analyses included Poisson regressions. The preference for purchasing generic drugs was 63.2% (95%CI 61.4-64.9). The variables correlated with this preference in the fully adjusted models were: male (prevalence ratio [PR] = 1.08; 95%CI 1.03-1.14), age of 20-39 years (PR = 1.10; 95%CI 1.02-1.20), low socioeconomic status (PR = 1.15; 95%CI 1.03-1.28), and good knowledge about generic drugs (PR= 4.66; 95%CI 2.89-7.52). Among those who preferred to purchase generic drugs, 55.1% have reported accepting to replace the prescribed drug (if not a generic) with the equivalent generic drug. Another correlate of the preference for purchasing generic drugs was because individuals consider their quality equivalent to reference medicines (PR = 2.15; 95%CI 1.93-2.41). Knowledge about generic drugs was the main correlate of the preference for purchasing generic drugs. The greater the knowledge or positive perception about generic drugs, the greater is the preference to purchase them. Therefore, educational campaigns for healthcare professionals and consumers appear to be the best strategy for expanding the use of generic drugs in Brazil.

Advertising and generic market entry.

Science.gov (United States)

Königbauer, Ingrid

2007-03-01

The effect of purely persuasive advertising on generic market entry and social welfare is analysed. An incumbent has the possibility to invest in advertising which affects the prescribing physician's perceived relative qualities of the brand-name and the generic version of the drug. Advertising creates product differentiation and can induce generic market entry which is deterred without differentiation due to strong Bertrand competition. However, over-investment in advertising can deter generic market entry under certain conditions and reduces welfare as compared to accommodated market entry.

Preparation and validation of gross alpha/beta samples used in EML's quality assessment program

International Nuclear Information System (INIS)

Scarpitta, S.C.

1997-10-01

A set of water and filter samples have been incorporated into the existing Environmental Measurements Laboratory's (EML) Quality Assessment Program (QAP) for gross alpha/beta determinations by participating DOE laboratories. The participating laboratories are evaluated by comparing their results with the EML value. The preferred EML method for measuring water and filter samples, described in this report, uses gas flow proportional counters with 2 in. detectors. Procedures for sample preparation, quality control and instrument calibration are presented. Liquid scintillation (LS) counting is an alternative technique that is suitable for quantifying both the alpha ( 241 Am, 230 Th and 238 Pu) and beta ( 90 Sr/ 90 Y) activity concentrations in the solutions used to prepare the QAP water and air filter samples. Three LS counting techniques (Cerenkov, dual dpm and full spectrum analysis) are compared. These techniques may be used to validate the activity concentrations of each component in the alpha/beta solution before the QAP samples are actually prepared

Sample preparation and characterization of technetium metal

International Nuclear Information System (INIS)

Minato, Kazuo; Serizawa, Hiroyuki; Fukuda, Kousaku; Itoh, Mitsuo

1997-10-01

Technetium-99 is a long-lived fission product with a half-life of about 2.1 x 10 5 years, which decays by β-emission. For the transmutation of 99 Tc, research on solid technetium was started. Technetium metal powder purchased was analyzed by X-ray diffraction, γ-ray spectrometry, and inductively coupled plasma-atomic emission spectrometry and -mass spectrometry. The lattice parameters obtained were agreed with the reported values. The metallic impurity was about 15 ppm, where aluminum and iron contributed mainly. No impurity nuclide with γ-emission was found. Using the technetium metal powder, button-, rod-, and disk-shaped samples of technetium metal were prepared by arc-melting technique. Thermal diffusivity of technetium metal was measured on a disk sample from room temperature to 1173 K by laser flash method. The thermal diffusivity decreased with increasing temperature though it was almost constant above 600 K. (author)

Comparison of leach results from field and laboratory prepared samples

International Nuclear Information System (INIS)

Oblath, S.B.; Langton, C.A.

1985-01-01

The leach behavior of saltstone prepared in the laboratory agrees well with that from samples mixed in the field using the Littleford mixer. Leach rates of nitrates and cesium from the current reference formulation saltstone were compared. The laboratory samples were prepared using simulated salt solution; those in the field used Tank 50 decontaminated supernate. For both nitrate and cesium, the field and laboratory samples showed nearly identical leach rates for the first 30 to 50 days. For the remaining period of the test, the field samples showed higher leach rates with the maximum difference being less than a factor of three. Ruthenium and antimony were present in the Tank 50 supernate in known amounts. Antimony-125 was observed in the leachate and a fractional leach rate was calculated to be at least a factor of ten less than that of 137 Cs. No 106 Ru was observed in the leachate, and the release rate was not calculated. However, based on the detection limits for the analysis, the ruthenium leach rate must also be at least a factor of ten less than cesium. These data are the first measurements of the leach rates of Ru and Sb from saltstone. The nitrate leach rates for these samples were 5 x 10 -5 grams of nitrate per square cm per day after 100 days for the laboratory samples and after 200 days for the field samples. These values are consistent with the previously measured leach rates for reference formulation saltstone. The relative standard deviation in the leach rate is about 15% for the field samples, which all were produced from one batch of saltstone, and about 35% for the laboratory samples, which came from different batches. These are the first recorded estimates of the error in leach rates for saltstone

The NOSAMS sample preparation laboratory in the next millenium: Progress after the WOCE program

International Nuclear Information System (INIS)

Gagnon, Alan R.; McNichol, Ann P.; Donoghue, Joanne C.; Stuart, Dana R.; Reden, Karl von

2000-01-01

Since 1991, the primary charge of the National Ocean Sciences AMS (NOSAMS) facility at the Woods Hole Oceanographic Institution has been to supply high throughput, high precision AMS 14 C analyses for seawater samples collected as part of the World Ocean Circulation Experiment (WOCE). Approximately 13,000 samples taken as part of WOCE should be fully analyzed by the end of Y2K. Additional sample sources and techniques must be identified and incorporated if NOSAMS is to continue in its present operation mode. A trend in AMS today is the ability to routinely process and analyze radiocarbon samples that contain tiny amounts ( 14 C analysis has been recognized as a major facility goal. The installation of a new 134-position MC-SNICS ion source, which utilizes a smaller graphite target cartridge than presently used, is one step towards realizing this goal. New preparation systems constructed in the sample preparation laboratory (SPL) include an automated bank of 10 small-volume graphite reactors, an automated system to process organic carbon samples, and a multi-dimensional preparative capillary gas chromatograph (PCGC)

Collection and preparation of bottom sediment samples for analysis of radionuclides and trace elements

International Nuclear Information System (INIS)

2003-07-01

The publication is the first in a series of TECDOCs on sampling and sample handling as part of the IAEA support to improve reliability of nuclear analytical techniques (NATs) in Member State laboratories. The purpose of the document is to provide information on the methods for collecting sediments, the equipment used, and the sample preparation techniques for radionuclide and elemental analysis. The most appropriate procedures for defining the strategies and criteria for selecting sampling locations, for sample storage and transportation are also given. Elements of QA/QC and documentation needs for sampling and sediment analysis are discussed. Collection and preparation of stream and river bottom sediments, lake bottom sediments, estuary bottom sediments, and marine (shallow) bottom sediments are covered. The document is intended to be a comprehensive manual for the collection and preparation of bottom sediments as a prerequisite to obtain representative and meaningful results using NATs. Quality assurance and quality control (QA/QC) is emphasized as an important aspect to ensure proper collection, transportation, preservation, and analysis since it forms the basis for interpretation and legislation. Although there are many approaches and methods available for sediment analyses, the scope of the report is limited to sample preparation for (1) analysis of radionuclides (including sediment dating using radionuclides such as Pb-210 and Cs-137) and (2) analysis of trace, minor and major elements using nuclear and related analytical techniques such as NAA, XRF and PIXE

Collection and preparation of bottom sediment samples for analysis of radionuclides and trace elements

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

The publication is the first in a series of TECDOCs on sampling and sample handling as part of the IAEA support to improve reliability of nuclear analytical techniques (NATs) in Member State laboratories. The purpose of the document is to provide information on the methods for collecting sediments, the equipment used, and the sample preparation techniques for radionuclide and elemental analysis. The most appropriate procedures for defining the strategies and criteria for selecting sampling locations, for sample storage and transportation are also given. Elements of QA/QC and documentation needs for sampling and sediment analysis are discussed. Collection and preparation of stream and river bottom sediments, lake bottom sediments, estuary bottom sediments, and marine (shallow) bottom sediments are covered. The document is intended to be a comprehensive manual for the collection and preparation of bottom sediments as a prerequisite to obtain representative and meaningful results using NATs. Quality assurance and quality control (QA/QC) is emphasized as an important aspect to ensure proper collection, transportation, preservation, and analysis since it forms the basis for interpretation and legislation. Although there are many approaches and methods available for sediment analyses, the scope of the report is limited to sample preparation for (1) analysis of radionuclides (including sediment dating using radionuclides such as Pb-210 and Cs-137) and (2) analysis of trace, minor and major elements using nuclear and related analytical techniques such as NAA, XRF and PIXE.

Microfluidic devices for sample preparation and rapid detection of foodborne pathogens.

Science.gov (United States)

Kant, Krishna; Shahbazi, Mohammad-Ali; Dave, Vivek Priy; Ngo, Tien Anh; Chidambara, Vinayaka Aaydha; Than, Linh Quyen; Bang, Dang Duong; Wolff, Anders

2018-03-10

Rapid detection of foodborne pathogens at an early stage is imperative for preventing the outbreak of foodborne diseases, known as serious threats to human health. Conventional bacterial culturing methods for foodborne pathogen detection are time consuming, laborious, and with poor pathogen diagnosis competences. This has prompted researchers to call the current status of detection approaches into question and leverage new technologies for superior pathogen sensing outcomes. Novel strategies mainly rely on incorporating all the steps from sample preparation to detection in miniaturized devices for online monitoring of pathogens with high accuracy and sensitivity in a time-saving and cost effective manner. Lab on chip is a blooming area in diagnosis, which exploits different mechanical and biological techniques to detect very low concentrations of pathogens in food samples. This is achieved through streamlining the sample handling and concentrating procedures, which will subsequently reduce human errors and enhance the accuracy of the sensing methods. Integration of sample preparation techniques into these devices can effectively minimize the impact of complex food matrix on pathogen diagnosis and improve the limit of detections. Integration of pathogen capturing bio-receptors on microfluidic devices is a crucial step, which can facilitate recognition abilities in harsh chemical and physical conditions, offering a great commercial benefit to the food-manufacturing sector. This article reviews recent advances in current state-of-the-art of sample preparation and concentration from food matrices with focus on bacterial capturing methods and sensing technologies, along with their advantages and limitations when integrated into microfluidic devices for online rapid detection of pathogens in foods and food production line. Copyright © 2018. Published by Elsevier Inc.

Rapid immunohistochemical diagnosis of tobacco mosaic virus disease by microwave-assisted plant sample preparation

Science.gov (United States)

Zellnig, Günther; Möstl, Stefan; Zechmann, Bernd

2013-01-01

Immunoelectron microscopy is a powerful method to diagnose viral diseases and to study the distribution of the viral agent within plant cells and tissues. Nevertheless, current protocols for the immunological detection of viral diseases with transmission electron microscopy (TEM) in plants take between 3 and 6 days and are therefore not suited for rapid diagnosis of virus diseases in plants. In this study, we describe a method that allows rapid cytohistochemical detection of tobacco mosaic virus (TMV) in leaves of tobacco plants. With the help of microwave irradiation, sample preparation of the leaves was reduced to 90 min. After sample sectioning, virus particles were stained on the sections by immunogold labelling of the viral coat protein, which took 100 min. After investigation with the TEM, a clear visualization of TMV in tobacco cells was achieved altogether in about half a day. Comparison of gold particle density by image analysis revealed that samples prepared with the help of microwave irradiation yielded significantly higher gold particle density as samples prepared conventionally at room temperature. This study clearly demonstrates that microwave-assisted plant sample preparation in combination with cytohistochemical localization of viral coat protein is well suited for rapid diagnosis of plant virus diseases in altogether about half a day by TEM. PMID:23580761

Protocols for the analytical characterization of therapeutic monoclonal antibodies. II - Enzymatic and chemical sample preparation.

Science.gov (United States)

Bobaly, Balazs; D'Atri, Valentina; Goyon, Alexandre; Colas, Olivier; Beck, Alain; Fekete, Szabolcs; Guillarme, Davy

2017-08-15

The analytical characterization of therapeutic monoclonal antibodies and related proteins usually incorporates various sample preparation methodologies. Indeed, quantitative and qualitative information can be enhanced by simplifying the sample, thanks to the removal of sources of heterogeneity (e.g. N-glycans) and/or by decreasing the molecular size of the tested protein by enzymatic or chemical fragmentation. These approaches make the sample more suitable for chromatographic and mass spectrometric analysis. Structural elucidation and quality control (QC) analysis of biopharmaceutics are usually performed at intact, subunit and peptide levels. In this paper, general sample preparation approaches used to attain peptide, subunit and glycan level analysis are overviewed. Protocols are described to perform tryptic proteolysis, IdeS and papain digestion, reduction as well as deglycosylation by PNGase F and EndoS2 enzymes. Both historical and modern sample preparation methods were compared and evaluated using rituximab and trastuzumab, two reference therapeutic mAb products approved by Food and Drug Administration (FDA) and European Medicines Agency (EMA). The described protocols may help analysts to develop sample preparation methods in the field of therapeutic protein analysis. Copyright © 2017 Elsevier B.V. All rights reserved.

The NOSAMS sample preparation laboratory in the next millenium: Progress after the WOCE program

Energy Technology Data Exchange (ETDEWEB)

Gagnon, Alan R. E-mail: agagnon@whoi.edu; McNichol, Ann P.; Donoghue, Joanne C.; Stuart, Dana R.; Reden, Karl von

2000-10-01

Since 1991, the primary charge of the National Ocean Sciences AMS (NOSAMS) facility at the Woods Hole Oceanographic Institution has been to supply high throughput, high precision AMS {sup 14}C analyses for seawater samples collected as part of the World Ocean Circulation Experiment (WOCE). Approximately 13,000 samples taken as part of WOCE should be fully analyzed by the end of Y2K. Additional sample sources and techniques must be identified and incorporated if NOSAMS is to continue in its present operation mode. A trend in AMS today is the ability to routinely process and analyze radiocarbon samples that contain tiny amounts (<100 {mu}g) of carbon. The capability to mass-produce small samples for {sup 14}C analysis has been recognized as a major facility goal. The installation of a new 134-position MC-SNICS ion source, which utilizes a smaller graphite target cartridge than presently used, is one step towards realizing this goal. New preparation systems constructed in the sample preparation laboratory (SPL) include an automated bank of 10 small-volume graphite reactors, an automated system to process organic carbon samples, and a multi-dimensional preparative capillary gas chromatograph (PCGC)

Sample preparation method for induced mutation on orchid

International Nuclear Information System (INIS)

Suhaimi Musa; Sakinah Ariffin

2005-01-01

Studies on the induction of mutation in Dendrobium orchid at MINT has produced a number of new orchid mutant cultivars. Tissue culture techniques on orchid seeds and meristem cloning are employed in preparing the samples for the mutation induction. Solid medium based on the Murashige and Skoog (1962) and liquid medium based on Vacin and Went (1949) were found to be suitable in producing protocorm like bodies (PLBs) that are required for the irradiation treatment. (Author)

[Standard sample preparation method for quick determination of trace elements in plastic].

Science.gov (United States)

Yao, Wen-Qing; Zong, Rui-Long; Zhu, Yong-Fa

2011-08-01

Reference sample was prepared by masterbatch method, containing heavy metals with known concentration of electronic information products (plastic), the repeatability and precision were determined, and reference sample preparation procedures were established. X-Ray fluorescence spectroscopy (XRF) analysis method was used to determine the repeatability and uncertainty in the analysis of the sample of heavy metals and bromine element. The working curve and the metrical methods for the reference sample were carried out. The results showed that the use of the method in the 200-2000 mg x kg(-1) concentration range for Hg, Pb, Cr and Br elements, and in the 20-200 mg x kg(-1) range for Cd elements, exhibited a very good linear relationship, and the repeatability of analysis methods for six times is good. In testing the circuit board ICB288G and ICB288 from the Mitsubishi Heavy Industry Company, results agreed with the recommended values.

Encouraging generic use can yield significant savings.

Science.gov (United States)

Zimmerman, Christina

2012-11-01

Key findings. (1) Zero copayment for generic drugs is the greatest influencer of generic statin utilization. (2) Both higher copayments for generic drugs and lower copayments for competing brands are associated with a decreased probability of using generic statins. (3) Prior authorization and step therapy requirements for brand-name statins are associated with an increased use of generic drugs. (4) Greater use of generic statins should reduce costs for patients, plans, and Medicare.

Cytotoxicity of Light-Cured Dental Materials according to Different Sample Preparation Methods

Directory of Open Access Journals (Sweden)

Myung-Jin Lee

2017-03-01

Full Text Available Dental light-cured resins can undergo different degrees of polymerization when applied in vivo. When polymerization is incomplete, toxic monomers may be released into the oral cavity. The present study assessed the cytotoxicity of different materials, using sample preparation methods that mirror clinical conditions. Composite and bonding resins were used and divided into four groups according to sample preparation method: uncured; directly cured samples, which were cured after being placed on solidified agar; post-cured samples were polymerized before being placed on agar; and “removed unreacted layer” samples had their oxygen-inhibition layer removed after polymerization. Cytotoxicity was evaluated using an agar diffusion test, MTT assay, and confocal microscopy. Uncured samples were the most cytotoxic, while removed unreacted layer samples were the least cytotoxic (p < 0.05. In the MTT assay, cell viability increased significantly in every group as the concentration of the extracts decreased (p < 0.05. Extracts from post-cured and removed unreacted layer samples of bonding resin were less toxic than post-cured and removed unreacted layer samples of composite resin. Removal of the oxygen-inhibition layer resulted in the lowest cytotoxicity. Clinicians should remove unreacted monomers on the resin surface immediately after restoring teeth with light-curing resin to improve the restoration biocompatibility.

Sample preparation prior to the LC-MS-based metabolomics/metabonomics of blood-derived samples.

Science.gov (United States)

Gika, Helen; Theodoridis, Georgios

2011-07-01

Blood represents a very important biological fluid and has been the target of continuous and extensive research for diagnostic, or health and drug monitoring reasons. Recently, metabonomics/metabolomics have emerged as a new and promising 'omics' platform that shows potential in biomarker discovery, especially in areas such as disease diagnosis, assessment of drug efficacy or toxicity. Blood is collected in various establishments in conditions that are not standardized. Next, the samples are prepared and analyzed using different methodologies or tools. When targeted analysis of key molecules (e.g., a drug or its metabolite[s]) is the aim, enforcement of certain measures or additional analyses may correct and harmonize these discrepancies. In omics fields such as those performed by holistic analytical approaches, no such rules or tools are available. As a result, comparison or correlation of results or data fusion becomes impractical. However, it becomes evident that such obstacles should be overcome in the near future to allow for large-scale studies that involve the assaying of samples from hundreds of individuals. In this case the effect of sample handling and preparation becomes very serious, in order to avoid wasting months of work from experts and expensive instrument time. The present review aims to cover the different methodologies applied to the pretreatment of blood prior to LC-MS metabolomic/metabonomic studies. The article tries to critically compare the methods and highlight issues that need to be addressed.

Recent advances in sample preparation techniques and methods of sulfonamides detection - A review.

Science.gov (United States)

Dmitrienko, Stanislava G; Kochuk, Elena V; Apyari, Vladimir V; Tolmacheva, Veronika V; Zolotov, Yury A

2014-11-19

Sulfonamides (SAs) have been the most widely used antimicrobial drugs for more than 70 years, and their residues in foodstuffs and environmental samples pose serious health hazards. For this reason, sensitive and specific methods for the quantification of these compounds in numerous matrices have been developed. This review intends to provide an updated overview of the recent trends over the past five years in sample preparation techniques and methods for detecting SAs. Examples of the sample preparation techniques, including liquid-liquid and solid-phase extraction, dispersive liquid-liquid microextraction and QuEChERS, are given. Different methods of detecting the SAs present in food and feed and in environmental, pharmaceutical and biological samples are discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

Monolith Chromatography as Sample Preparation Step in Virome Studies of Water Samples.

Science.gov (United States)

Gutiérrez-Aguirre, Ion; Kutnjak, Denis; Rački, Nejc; Rupar, Matevž; Ravnikar, Maja

2018-01-01

Viruses exist in aquatic media and many of them use this media as transmission route. Next-generation sequencing (NGS) technologies have opened new doors in virus research, allowing also to reveal a hidden diversity of viral species in aquatic environments. Not surprisingly, many of the newly discovered viruses are found in environmental fresh and marine waters. One of the problems in virome research can be the low amount of viral nucleic acids present in the sample in contrast to the background ones (host, eukaryotic, prokaryotic, environmental). Therefore, virus enrichment prior to NGS is necessary in many cases. In water samples, an added problem resides in the low concentration of viruses typically present in aquatic media. Different concentration strategies have been used to overcome such limitations. CIM monoliths are a new generation of chromatographic supports that due to their particular structural characteristics are very efficient in concentration and purification of viruses. In this chapter, we describe the use of CIM monolithic chromatography for sample preparation step in NGS studies targeting viruses in fresh or marine water. The step-by-step protocol will include a case study where CIM concentration was used to study the virome of a wastewater sample using NGS.

Generic impact statement for commercial radioactive waste management

International Nuclear Information System (INIS)

Unruh, C.M.

1976-01-01

ERDA is preparing a generic environmental impact statement on the treatment and disposal of waste resulting from commercial reactors and post fission operations in the light water reactor (LWR) fuel cycle. Expert contributions will be provided by many of the ERDA national laboratories and contractors. The waste management aspects of the statement will be based on available technology as presented in the recently issued ''Alternatives for Managing Waste from Reactors and Post Fission Operations in the LWR Fuel Cycle,'' ERDA-76-43 Document. This 1500 page, five volume Technical Alternative Document (TAD) describes the status of technology (to September, 1975) for handling post fission radioactive waste generated by the production of electricity by nuclear power light water reactor-generator systems. The statement will be generic in nature discussing typical or hypothetical facilities in typical or hypothetical environments. It is not intended to replace environmental statements required in support of specific projects nor for Nuclear Regulatory Commission licensing procedures. A major purpose of the generic statement is to inform the public and to solicit comments on the ERDA program for: (1) the final disposition of commercial radioactive waste, (2) waste treatment, (3) waste interim storage, and (4) transportation of waste. The statement will discuss the ERDA contingency program to provide retrievable storage of such waste if they should be transferred to Federal custody prior to the availability of the geologic isolation facilities for terminal disposal. The generic statement will not address radioactive waste resulting from U.S. Defense Programs, the mining or milling of uranium, the management of waste from the breeder reactor program, waste from other nations, nor will it include an evaluation of the impact of waste resulting from power sources other than light water reactors

78 FR 33097 - Agency Information Collection Activities; Proposed Collection; Comment Request: Generic Clearance...

Science.gov (United States)

2013-06-03

... target population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. No... and opinions, [[Page 33098

Factors influencing the preference for purchasing generic drugs in a Southern Brazilian city

Directory of Open Access Journals (Sweden)

Marília Cruz Guttier

Full Text Available ABSTRACT OBJECTIVE The objective of this study is to identify factors associated with the preference for purchasing generic drugs in a medium-sized municipality in Southern Brazil. METHODS We have analyzed data from a population-based cross-sectional study conducted in 2012 with a sample of 2,856 adults (≥ 20 years old. The preference for purchasing generic drugs was the main outcome. The explanatory variables were the demographic and socioeconomic variables. Statistical analyses included Poisson regressions. RESULTS The preference for purchasing generic drugs was 63.2% (95%CI 61.4–64.9. The variables correlated with this preference in the fully adjusted models were: male (prevalence ratio [PR] = 1.08; 95%CI 1.03–1.14, age of 20–39 years (PR = 1.10; 95%CI 1.02–1.20, low socioeconomic status (PR = 1.15; 95%CI 1.03–1.28, and good knowledge about generic drugs (PR= 4.66; 95%CI 2.89–7.52. Among those who preferred to purchase generic drugs, 55.1% have reported accepting to replace the prescribed drug (if not a generic with the equivalent generic drug. Another correlate of the preference for purchasing generic drugs was because individuals consider their quality equivalent to reference medicines (PR = 2.15; 95%CI 1.93–2.41. CONCLUSIONS Knowledge about generic drugs was the main correlate of the preference for purchasing generic drugs. The greater the knowledge or positive perception about generic drugs, the greater is the preference to purchase them. Therefore, educational campaigns for healthcare professionals and consumers appear to be the best strategy for expanding the use of generic drugs in Brazil.

76 FR 57767 - Proposed Generic Communication; Draft NRC Generic Letter 2011-XX: Seismic Risk Evaluations for...

Science.gov (United States)

2011-09-16

... NUCLEAR REGULATORY COMMISSION [NRC-2011-0204] Proposed Generic Communication; Draft NRC Generic Letter 2011-XX: Seismic Risk Evaluations for Operating Reactors AGENCY: Nuclear Regulatory Commission... FR 54507), that requested public comment on Draft NRC Generic Letter 2011- XX: Seismic Risk...

Electrodeposition as a sample preparation technique for TXRF analysis

International Nuclear Information System (INIS)

Griesel, S.; Reus, U.; Prange, A.

2000-01-01

TXRF analysis of trace elements at concentrations in the μg/L range and below in high salt matrices normally requires a number of sample preparation steps that include separation of the salt matrix and preconcentration of the trace elements. A neat approach which allows samples to be prepared straightforwardly in a single step involves the application of electrochemical deposition using the TXRF sample support itself as an electrode. For this work a common three-electrode arrangement (radiometer analytical) with a rotating disc electrode as the working electrode, as is frequently employed in voltametric analysis, has been used. A special electrode tip has been constructed as a holder for the sample carrier which consists of polished glassy carbon. This material has been proven to be suitable for both its electrical and chemical properties. Measurements of the trace elements were performed using the ATOMIKA 8030C TXRF spectrometer, with the option of variable incident angles. In first experiments an artificial sea water matrix containing various trace elements in the μg/L range has been used. Elements such as Cr, Mn, Fe, Co, Ni, Cu, Zn, Ag, Cd, Hg, and Pb deposited on glassy carbon carriers. The deposition can be optimized by controlling the potential of the working electrode with respect to the reference electrode. Metal ions with a suitable standard potential are reduced to the metallic state and plated onto the electrode surface. When deposition is finished the sample carrier is demounted, rinsed with ultra-pure water and measured directly. Deposition yields for the elements under investigation are quite similar, and with an appropriate choice of the reference element, quantification can be achieved directly by internal standardization. The influence of parameters such as time, pH value, and trace element concentration on the deposition yield has been examined, and the results will be presented along with reproducibility studies. (author)

Guidance document for preparing water sampling and analysis plans for UMTRA Project sites. Revision 1

International Nuclear Information System (INIS)

1995-09-01

A water sampling and analysis plan (WSAP) is prepared for each Uranium Mill Tailings Remedial Action (UMTRA) Project site to provide the rationale for routine ground water sampling at disposal sites and former processing sites. The WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the routine ground water monitoring stations at each site. This guidance document has been prepared by the Technical Assistance Contractor (TAC) for the US Department of Energy (DOE). Its purpose is to provide a consistent technical approach for sampling and monitoring activities performed under the WSAP and to provide a consistent format for the WSAP documents. It is designed for use by the TAC in preparing WSAPs and by the DOE, US Nuclear Regulatory Commission, state and tribal agencies, other regulatory agencies, and the public in evaluating the content of WSAPS

Sample preparation for large-scale bioanalytical studies based on liquid chromatographic techniques.

Science.gov (United States)

Medvedovici, Andrei; Bacalum, Elena; David, Victor

2018-01-01

Quality of the analytical data obtained for large-scale and long term bioanalytical studies based on liquid chromatography depends on a number of experimental factors including the choice of sample preparation method. This review discusses this tedious part of bioanalytical studies, applied to large-scale samples and using liquid chromatography coupled with different detector types as core analytical technique. The main sample preparation methods included in this paper are protein precipitation, liquid-liquid extraction, solid-phase extraction, derivatization and their versions. They are discussed by analytical performances, fields of applications, advantages and disadvantages. The cited literature covers mainly the analytical achievements during the last decade, although several previous papers became more valuable in time and they are included in this review. Copyright © 2017 John Wiley & Sons, Ltd.

Sample Preparation and Identification of Biological, Chemical and Mid-Spectrum Agents

National Research Council Canada - National Science Library

Hancock, J. R; Dragon, D. C

2005-01-01

A general survey of sample preparation and identification techniques for biological, chemical and mid-spectrum agents was conducted as part of Canada's contribution to a joint NATO Allied Engineering Publication (AEP) handbook...

Bovine liver sample preparation and micro-homogeneity study for Cu and Zn determination by solid sampling electrothermal atomic absorption spectrometry

International Nuclear Information System (INIS)

Nomura, Cassiana S.; Silva, Cintia S.; Nogueira, Ana R.A.; Oliveira, Pedro V.

2005-01-01

This work describes a systematic study for the bovine liver sample preparation for Cu and Zn determination by solid sampling electrothermal atomic absorption spectrometry. The main parameters investigated were sample drying, grinding process, particle size, sample size, microsample homogeneity, and their relationship with the precision and accuracy of the method. A bovine liver sample was prepared using different drying procedures: (1) freeze drying, and (2) drying in a household microwave oven followed by drying in a stove at 60 deg. C until constant mass. Ball and cryogenic mills were used for grinding. Less sensitive wavelengths for Cu (216.5 nm) and Zn (307.6 nm), and Zeeman-based three-field background correction for Cu were used to diminish the sensitivities. The pyrolysis and atomization temperatures adopted were 1000 deg. C and 2300 deg. C for Cu, and 700 deg. C and 1700 deg. C for Zn, respectively. For both elements, it was possible to calibrate the spectrometer with aqueous solutions. The use of 250 μg of W + 200 μg of Rh as permanent chemical modifier was imperative for Zn. Under these conditions, the characteristic mass and detection limit were 1.4 ng and 1.6 ng for Cu, and 2.8 ng and 1.3 ng for Zn, respectively. The results showed good agreement (95% confidence level) for homogeneity of the entire material (> 200 mg) when the sample was dried in microwave/stove and ground in a cryogenic mill. The microsample homogeneity study showed that Zn is more dependent on the sample pretreatment than Cu. The bovine liver sample prepared in microwave/stove and ground in a cryogenic mill presented results with the lowest relative standard deviation for Cu than Zn. Good accuracy and precision were observed for bovine liver masses higher than 40 μg for Cu and 30 μg for Zn. The concentrations of Cu and Zn in the prepared bovine liver sample were 223 mg kg - 1 and 128 mg kg - 1 , respectively. The relative standard deviations were lower than 6% (n = 5). The

Generics Pricing: The Greek Paradox.

Science.gov (United States)

Karafyllis, Ioannis; Variti, Lamprini

2017-01-01

This paper explains and develops a methodological framework to help evaluate the performance of generic pharmaceutical policies and the correct evaluation of generics sales. Until today erroneous recording of generics does not help proper pricing and their penetration in the Greek market. This classifies Greece on the outliners in every study or comparison that is referred on papers or studies.

Sample preparation: a critical step in the analysis of cholesterol oxidation products.

Science.gov (United States)

Georgiou, Christiana A; Constantinou, Michalis S; Kapnissi-Christodoulou, Constantina P

2014-02-15

In recent years, cholesterol oxidation products (COPs) have drawn scientific interest, particularly due to their implications on human health. A big number of these compounds have been demonstrated to be cytotoxic, mutagenic, and carcinogenic. The main source of COPs is through diet, and particularly from the consumption of cholesterol-rich foods. This raises questions about the safety of consumers, and it suggests the necessity for the development of a sensitive and a reliable analytical method in order to identify and quantify these components in food samples. Sample preparation is a necessary step in the analysis of COPs in order to eliminate interferences and increase sensitivity. Numerous publications have, over the years, reported the use of different methods for the extraction and purification of COPs. However, no method has, so far, been established as a routine method for the analysis of COPs in foods. Therefore, it was considered important to overview different sample preparation procedures and evaluate the different preparative parameters, such as time of saponification, the type of organic solvents for fat extraction, the stationary phase in solid phase extraction, etc., according to recovery, precision and simplicity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preparation of solid-state samples of a transition metal coordination compound for synchrotron radiation photoemission studies

CERN Document Server

Crotti, C; Celestino, T; Fontana, S

2003-01-01

The aim of this research was to identify a sample preparation method suitable for the study of transition metal complexes by photoemission spectroscopy with synchrotron radiation as the X-ray source, even in the case where the compound is not evaporable. Solid-phase samples of W(CO) sub 4 (dppe) [dppe=1,2-bis(diphenylphosphino)ethane] were prepared according to different methods and their synchrotron radiation XPS spectra measured. The spectra acquired from samples prepared by spin coating show core level peaks only slightly broader than the spectrum recorded from UHV evaporated samples. Moreover, for these samples the reproducibility of the binding energy values is excellent. The dependence of the spin coating technique on parameters such as solvent and solution concentration, spinning speed and support material was studied. The same preparation method also allowed the acquisition of valence band spectra, the main peaks of which were clearly resolved. The results suggest that use of the spin coating techniqu...

Generic delivery of payload of nanoparticles intracellularly via hybrid polymer capsules for bioimaging applications.

Directory of Open Access Journals (Sweden)

Haider Sami

Full Text Available Towards the goal of development of a generic nanomaterial delivery system and delivery of the 'as prepared' nanoparticles without 'further surface modification' in a generic way, we have fabricated a hybrid polymer capsule as a delivery vehicle in which nanoparticles are loaded within their cavity. To this end, a generic approach to prepare nanomaterials-loaded polyelectrolyte multilayered (PEM capsules has been reported, where polystyrene sulfonate (PSS/polyallylamine hydrochloride (PAH polymer capsules were employed as nano/microreactors to synthesize variety of nanomaterials (metal nanoparticles; lanthanide doped inorganic nanoparticles; gadolinium based nanoparticles, cadmium based nanoparticles; different shapes of nanoparticles; co-loading of two types of nanoparticles in their hollow cavity. These nanoparticles-loaded capsules were employed to demonstrate generic delivery of payload of nanoparticles intracellularly (HeLa cells, without the need of individual nanoparticle surface modification. Validation of intracellular internalization of nanoparticles-loaded capsules by HeLa cells was ascertained by confocal laser scanning microscopy. The green emission from Tb(3+ was observed after internalization of LaF(3:Tb(3+(5% nanoparticles-loaded capsules by HeLa cells, which suggests that nanoparticles in hybrid capsules retain their functionality within the cells. In vitro cytotoxicity studies of these nanoparticles-loaded capsules showed less/no cytotoxicity in comparison to blank capsules or untreated cells, thus offering a way of evading direct contact of nanoparticles with cells because of the presence of biocompatible polymeric shell of capsules. The proposed hybrid delivery system can be potentially developed to avoid a series of biological barriers and deliver multiple cargoes (both simultaneous and individual delivery without the need of individual cargo design/modification.

Microfluidic devices for sample preparation and rapid detection of foodborne pathogens

DEFF Research Database (Denmark)

Kant, Krishna; Shahbazi, Mohammad-Ali; Dave, Vivek Priy

2018-01-01

and improve the limit of detections. Integration of pathogen capturing bio-receptors on microfluidic devices is a crucial step, which can facilitate recognition abilities in harsh chemical and physical conditions, offering a great commercial benefit to the food-manufacturing sector. This article reviews...... diagnosis competences. This has prompted researchers to call the current status of detection approaches into question and leverage new technologies for superior pathogen sensing outcomes. Novel strategies mainly rely on incorporating all the steps from sample preparation to detection in miniaturized devices...... recent advances in current state-of-the-art of sample preparation and concentration from food matrices with focus on bacterial capturing methods and sensing technologies, along with their advantages and limitations when integrated into microfluidic devices for online rapid detection of pathogens in foods...

Sample preparation method for the combined extraction of ethyl glucuronide and drugs of abuse in hair.

Science.gov (United States)

Meier, Ulf; Briellmann, Thomas; Scheurer, Eva; Dussy, Franz

2018-04-01

Often in hair analysis, a small hair sample is available while the analysis of a multitude of structurally diverse substances with different concentration ranges is demanded. The analysis of the different substances often requires different sample preparation methods, increasing the amount of required hair sample. When segmental hair analysis is necessary, the amount of hair sample needed is further increased. Therefore, the required sample amount for a full analysis can quickly exceed what is available. To combat this problem, a method for the combined hair sample preparation using a single extraction procedure for analysis of ethyl glucuronide with liquid chromatography-multistage fragmentation mass spectrometry/multiple reaction monitoring (LC-MS 3 /MRM) and common drugs of abuse with LC-MRM was developed. The combined sample preparation is achieved by separating ethyl glucuronide from the drugs of abuse into separate extracts by fractionation in the solid-phase extraction step during sample clean-up. A full validation for all substances for the parameters selectivity, linearity, limit of detection, limit of quantification, accuracy, precision, matrix effects, and recovery was successfully completed. The following drugs of abuse were included in the method: Amphetamine; methamphetamine; 3,4-methylenedioxy-N-methylamphetamine (MDMA); 3,4-methylenedioxyamphetamine (MDA); 3,4-methylenedioxy-N-ethylamphetamine (MDE); morphine; 6-monoacetylmorphine; codeine; acetylcodeine; cocaine; benzoylecgonine; norcocaine; cocaethylene; methadone; 2-ethylidene-1,5-dimethyl-3,3-diphenylpyrrolidine (EDDP) and methylphenidate. In conclusion, as only 1 sample preparation is needed with 1 aliquot of hair, the presented sample preparation allows an optimal analysis of both ethyl glucuronide and of the drugs of abuse, even when the sample amount is a limiting factor. Copyright © 2017 John Wiley & Sons, Ltd.

NET 40 Generics Beginner's Guide

CERN Document Server

Mukherjee, Sudipta

2012-01-01

This is a concise, practical guide that will help you learn Generics in .NET, with lots of real world and fun-to-build examples and clear explanations. It is packed with screenshots to aid your understanding of the process. This book is aimed at beginners in Generics. It assumes some working knowledge of C# , but it isn't mandatory. The following would get the most use out of the book: Newbie C# developers struggling with Generics. Experienced C++ and Java Programmers who are migrating to C# and looking for an alternative to other generic frameworks like STL and JCF would find this book handy.

Study of sample preparation in the measurement of 36Ar(n, p)36Cl reaction cross section

International Nuclear Information System (INIS)

Jiang Songsheng; Hemick, T.K.

1992-01-01

The preparation of enriched 36 Ar gas samples and 36 Cl samples for the use in the AMS measurement of 36 Ar(n, p) 36 Cl reaction cross section was described. The 36 Ar samples prepared had the volumes of about 0.4 ml and the weights of about 0.5 mg. The uncertainty in atomic numbers of 36 Ar was (0.3∼0.4)%. The reaction product, 36 Cl, in the 36 Ar was collected and the AgCl samples were prepared

Dynamic Headspace Sampling as an Initial Step for Sample Preparation in Chromatographic Analysis.

Science.gov (United States)

Wojnowski, Wojciech; Majchrzak, Tomasz; Dymerski, Tomasz; Gębicki, Jacek; Namieśnik, Jacek

2017-11-01

This work represents a brief summary of the use of dynamic headspace (DHS) as a technique for sample preparation in chromatographic analysis. Despite numerous developments in the area of analyte isolation and enrichment, DHS remains one of the fundamental methods used with GC. In our opinion, interest in this technique will not diminish significantly because it conforms to stipulations of green analytical chemistry. Moreover, DHS fulfills the need for methods that facilitate detection and determination of analytes present at ultratrace levels in complex matrixes. The main focus of this work was placed on the theoretical fundamentals of this method. Also described herein were DHS development, the advantages and disadvantages of this technique compared with other headspace sampling techniques, and selected examples of its applications in food and environmental analyses.

Ultrasonic assisted extraction - an alternative for sample preparation (M4)

International Nuclear Information System (INIS)

Santos Junior, P.; Barbosa Junior, F.; Krug, F.J.; Trevizan, L.C.; Nobrega, J.A.

2002-01-01

Full text: In the last years the ultrasound assisted metal extraction has been frequency proposed as a simple and inexpensive alternative for sample preparation of biological and inorganic samples. The extraction effect is considered as being caused by acoustic cavitation, that is, bubble formation and subsequent disruptive action. The collapse of bubbles created by sonication of solutions results in the generation of extremely high local temperature and pressure gradients, which may be regarded as localized 'hot spots'. On a timescale of about 10 -10 s, effective local pressures and temperature of about 10 5 atm and about 5000 K, respectively, are generated under sonochemical conditions. Usually, this method uses a diluted acid medium decreasing blank values and reducing both reagents and time consumption compared to traditional wet digestion systems using conductive or microwave-assisted heating. Furthermore, sonication can also allow the preparation of samples directly within the sample container, thereby preventing sample losses and minimizing sample contamination. Although some controversial results concerning metals extraction behavior have been reported, they could be explained by analyte-matrix interaction and the ability of the ultrasonic processor to generate ultrasound (i.e. the use of an ultrasonic bath or an ultrasonic probe at different power, frequency, and amplitude). This contribution presents a review of ultrasound assisted metal extraction and recent performance data obtained in our laboratory for determination of elements in biological materials, soils and sediments by ICP-OES and ETAAS. The effect of extraction parameters, such as type and concentration of the leaching solution, sonication time and performance of ultrasonic processor (bath or probe) will be presented. (author)

Homogeneous immunosubtraction integrated with sample preparation is enabled by a microfluidic format

Science.gov (United States)

Apori, Akwasi A.; Herr, Amy E.

2011-01-01

Immunosubtraction is a powerful and resource-intensive laboratory medicine assay that reports both protein mobility and binding specificity. To expedite and automate this electrophoretic assay, we report on advances to the electrophoretic immunosubtraction assay by introducing a homogeneous, not heterogeneous, format with integrated sample preparation. To accomplish homogeneous immunosubtraction, a step-decrease in separation matrix pore-size at the head of a polyacrylamide gel electrophoresis (PAGE) separation channel enables ‘subtraction’ of target analyte when capture antibody is present (as the large immune-complex is excluded from PAGE), but no subtraction when capture antibody is absent. Inclusion of sample preparation functionality via small pore size polyacrylamide membranes is also key to automated operation (i.e., sample enrichment, fluorescence sample labeling, and mixing of sample with free capture antibody). Homogenous sample preparation and assay operation allows on-the-fly, integrated subtraction of one to multiple protein targets and reuse of each device. Optimization of the assay is detailed which allowed for ~95% subtraction of target with 20% non-specific extraction of large species at the optimal antibody-antigen ratio, providing conditions needed for selective target identification. We demonstrate the assay on putative markers of injury and inflammation in cerebrospinal fluid (CSF), an emerging area of diagnostics research, by rapidly reporting protein mobility and binding specificity within the sample matrix. We simultaneously detect S100B and C-reactive protein, suspected biomarkers for traumatic brain injury (TBI), in ~2 min. Lastly, we demonstrate S100B detection (65 nM) in raw human CSF with a lower limit of detection of ~3.25 nM, within the clinically relevant concentration range for detecting TBI in CSF. Beyond the novel CSF assay introduced here, a fully automated immunosubtraction assay would impact a spectrum of routine but labor

Effect of sample preparation methods on photometric determination of the tellurium and cobalt content in the samples of copper concentrates

Directory of Open Access Journals (Sweden)

Viktoriya Butenko

2016-03-01

Full Text Available Methods of determination of cobalt and nickel in copper concentrates currently used in factory laboratories are very labor intensive and time consuming. The limiting stage of the analysis is preliminary chemical sample preparation. Carrying out the decomposition process of industrial samples with concentrated mineral acids in open systems does not allow to improve the metrological characteristics of the methods, for this reason improvement the methods of sample preparation is quite relevant and has a practical interest. The work was dedicated to the determination of the optimal conditions of preliminary chemical preparation of copper concentrate samples for the subsequent determination of cobalt and tellurium in the obtained solution using tellurium-spectrophotometric method. Decomposition of the samples was carried out by acid dissolving in individual mineral acids and their mixtures by heating in an open system as well as by using ultrasonification and microwave radiation in a closed system. In order to select the optimal conditions for the decomposition of the samples in a closed system the phase contact time and ultrasonic generator’s power were varied. Intensification of the processes of decomposition of copper concentrates with nitric acid (1:1, ultrasound and microwave radiation allowed to transfer quantitatively cobalt and tellurium into solution spending 20 and 30 min respectively. This reduced the amount of reactants used and improved the accuracy of determination by running the process in strictly identical conditions.

Robotic sample preparation for radiochemical plutonium and americium analyses

International Nuclear Information System (INIS)

Stalnaker, N.; Beugelsdijk, T.; Thurston, A.; Quintana, J.

1985-01-01

A Zymate robotic system has been assembled and programmed to prepare samples for plutonium and americium analyses by radioactivity counting. The system performs two procedures: a simple dilution procedure and a TTA (xylene) extraction of plutonium. To perform the procedures, the robotic system executes 11 unit operations such as weighing, pipetting, mixing, etc. Approximately 150 programs, which require 64 kilobytes of memory, control the system. The system is now being tested with high-purity plutonium metal and plutonium oxide samples. Our studies indicate that the system can give results that agree within 5% at the 95% confidence level with determinations performed manually. 1 ref., 1 fig., 1 tab

Sample preparation composite and replicate strategy case studies for assay of solid oral drug products.

Science.gov (United States)

Nickerson, Beverly; Harrington, Brent; Li, Fasheng; Guo, Michele Xuemei

2017-11-30

Drug product assay is one of several tests required for new drug products to ensure the quality of the product at release and throughout the life cycle of the product. Drug product assay testing is typically performed by preparing a composite sample of multiple dosage units to obtain an assay value representative of the batch. In some cases replicate composite samples may be prepared and the reportable assay value is the average value of all the replicates. In previously published work by Harrington et al. (2014) [5], a sample preparation composite and replicate strategy for assay was developed to provide a systematic approach which accounts for variability due to the analytical method and dosage form with a standard error of the potency assay criteria based on compendia and regulatory requirements. In this work, this sample preparation composite and replicate strategy for assay is applied to several case studies to demonstrate the utility of this approach and its application at various stages of pharmaceutical drug product development. Copyright © 2017 Elsevier B.V. All rights reserved.

Integrated Automation of High-Throughput Screening and Reverse Phase Protein Array Sample Preparation

DEFF Research Database (Denmark)

Pedersen, Marlene Lemvig; Block, Ines; List, Markus

into automated robotic high-throughput screens, which allows subsequent protein quantification. In this integrated solution, samples are directly forwarded to automated cell lysate preparation and preparation of dilution series, including reformatting to a protein spotter-compatible format after the high......-throughput screening. Tracking of huge sample numbers and data analysis from a high-content screen to RPPAs is accomplished via MIRACLE, a custom made software suite developed by us. To this end, we demonstrate that the RPPAs generated in this manner deliver reliable protein readouts and that GAPDH and TFR levels can...

Influence of rice sample preparation and milling procedures on milling quality appraisals

Science.gov (United States)

The objective of this research was to investigate the effect of sample preparation and milling procedure on milling quality appraisals of rough rice. Samples of freshly harvested medium-grain rice (M202) with different initial moisture contents (MCs) ranging from 20.2% to 25.1% (w.b.) were used for...

Microextraction sample preparation techniques in biomedical analysis.

Science.gov (United States)

Szultka, Malgorzata; Pomastowski, Pawel; Railean-Plugaru, Viorica; Buszewski, Boguslaw

2014-11-01

Biologically active compounds are found in biological samples at relatively low concentration levels. The sample preparation of target compounds from biological, pharmaceutical, environmental, and food matrices is one of the most time-consuming steps in the analytical procedure. The microextraction techniques are dominant. Metabolomic studies also require application of proper analytical technique for the determination of endogenic metabolites present in biological matrix on trace concentration levels. Due to the reproducibility of data, precision, relatively low cost of the appropriate analysis, simplicity of the determination, and the possibility of direct combination of those techniques with other methods (combination types on-line and off-line), they have become the most widespread in routine determinations. Additionally, sample pretreatment procedures have to be more selective, cheap, quick, and environmentally friendly. This review summarizes the current achievements and applications of microextraction techniques. The main aim is to deal with the utilization of different types of sorbents for microextraction and emphasize the use of new synthesized sorbents as well as to bring together studies concerning the systematic approach to method development. This review is dedicated to the description of microextraction techniques and their application in biomedical analysis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Efficient Generic Functional Programming

NARCIS (Netherlands)

Alimarine, A.; Smetsers, J.E.W.

2005-01-01

Generic functions are defined by induction on the structural representation of types. As a consequence, by defining just a single generic operation, one acquires this operation over any particular data type. An instance on a specific type is generated by interpretation of the type's structure. A

Generic robot architecture

Science.gov (United States)

Bruemmer, David J [Idaho Falls, ID; Few, Douglas A [Idaho Falls, ID

2010-09-21

The present invention provides methods, computer readable media, and apparatuses for a generic robot architecture providing a framework that is easily portable to a variety of robot platforms and is configured to provide hardware abstractions, abstractions for generic robot attributes, environment abstractions, and robot behaviors. The generic robot architecture includes a hardware abstraction level and a robot abstraction level. The hardware abstraction level is configured for developing hardware abstractions that define, monitor, and control hardware modules available on a robot platform. The robot abstraction level is configured for defining robot attributes and provides a software framework for building robot behaviors from the robot attributes. Each of the robot attributes includes hardware information from at least one hardware abstraction. In addition, each robot attribute is configured to substantially isolate the robot behaviors from the at least one hardware abstraction.

Notes on sample preparation of food: food of plant and animal origins, and daily meals

International Nuclear Information System (INIS)

Heilgeist, M.

1992-01-01

The procedure of food sample preparation to determine their specific radioactivity, analogous to chemical residue analysis, is laid down in the relevant sets of regulations. Several procedural steps of sample preparation of single food and composite food are dealt with. The sample size necessary for gamma spectroscopy and Sr-89/Sr-90 analysis, and the incineration step to enrich radionuclides are explained. Finally, enrichment by freeze drying of the high-volatile radionuclide I-131 is considered. (orig.) [de

Sample collection and preparation of biofluids and extracts for gas chromatography-mass spectrometry.

Science.gov (United States)

Emwas, Abdul-Hamid M; Al-Talla, Zeyad A; Kharbatia, Najeh M

2015-01-01

To maximize the utility of gas chromatography-mass spectrometry (GC-MS) in metabonomics research, all stages of the experimental design should be standardized, including sample collection, storage, preparation, and sample separation. Moreover, the prerequisite for any GC-MS analysis is that a compound must be volatile and thermally stable if it is to be analyzed using this technique. Since many metabolites are nonvolatile and polar in nature, they are not readily amenable to analysis by GC-MS and require initial chemical derivatization of the polar functional groups in order to reduce the polarity and to increase the thermal stability and volatility of the analytes. In this chapter, an overview is presented of the optimum approach to sample collection, storage, and preparation for gas chromatography-mass spectrometry-based metabonomics with particular focus on urine samples as example of biofluids.

“No generics, Doctor!” The perspective of general practitioners in two French regions

Directory of Open Access Journals (Sweden)

Béatrice Riner

2017-11-01

Full Text Available Abstract Background Generic medicines are essential to controlling health expenditures. Their market share is still small in France. The discourse and practices of prescribers may play a major role in their use. The purpose of this study was to explore the knowledge, attitudes and practices of general practitioners (GPs toward generic medicines in two French regions with the lowest penetration rate of these products. Methods An observational study was carried out from October 2015 to February 2016 in Guadeloupe and Martinique. The first qualitative phase involved a diversified sample of 14 GPs who underwent semi-structured interviews. The second phase involved a random sample of 316 GPs (response rate = 74% who were administered a structured questionnaire developed from the results of the first phase. Results Seventy-eight percent of the participants defined a generic drug as a drug containing an active substance identical to a brand-name drug, but only 11% considered generic drugs to be equivalent to brand-name drugs, and the same proportion believed that the generic drugs were of doubtful quality. The primary recognized advantage of generic medicines was their lower cost (82%. The main drawbacks cited were the variability of their presentation (44%, the confusion that they caused for some patients (47%, frequent allegations of adverse side effects (37% and a lack of efficacy (24%, and frequent refusal by patients (26%. Seventy-four percent of the participants stated that they adapted their prescribing practices to the situation, and of this group, 47% prescribed the originator product simply on demand. Conclusion Most surveyed GPs were not hostile towards generic medicines. They were caught between the requirements of health insurance regimes and the opposition of numerous users and suggested that the patient information provided by health authorities should be improved and that drug composition and packaging should be made uniform.

Open focused microwave-assisted sample preparation for rapid total and mercury species determination in environmental solid samples

OpenAIRE

Tseng, C. M.; Garraud, H.; Amouroux, D.; Donard, O. F. X.; de Diego, A.

1998-01-01

This paper describes rapid, simple microwave-assisted leaching/ digestion procedures for total and mercury species determination in sediment samples and biomaterials. An open focused microwave system allowed the sample preparation time to be dramatically reduced to only 24 min when a power of 40-80 W was applied. Quantitative leaching of methylmercury from sediments by HNO3 solution and complete dissolution of biomaterials by an alkaline solution, such as 25% TMAH solution, were obtained. Met...

Sample preparation strategies for food and biological samples prior to nanoparticle detection and imaging

DEFF Research Database (Denmark)

Larsen, Erik Huusfeldt; Löschner, Katrin

2014-01-01

microscopy (TEM) proved to be necessary for trouble shooting of results obtained from AFFF-LS-ICP-MS. Aqueous and enzymatic extraction strategies were tested for thorough sample preparation aiming at degrading the sample matrix and to liberate the AgNPs from chicken meat into liquid suspension. The resulting...... AFFF-ICP-MS fractograms, which corresponded to the enzymatic digests, showed a major nano-peak (about 80 % recovery of AgNPs spiked to the meat) plus new smaller peaks that eluted close to the void volume of the fractograms. Small, but significant shifts in retention time of AFFF peaks were observed...... for the meat sample extracts and the corresponding neat AgNP suspension, and rendered sizing by way of calibration with AgNPs as sizing standards inaccurate. In order to gain further insight into the sizes of the separated AgNPs, or their possible dissolved state, fractions of the AFFF eluate were collected...

Effect of method of sample preparation on ruminal in situ ...

African Journals Online (AJOL)

Midmar) was harvested at three and four weeks after cutting and fertilizing with 200 kg nitrogen (N)/ha. Freshly cut herbage was used to investigate the following four sample preparation methods. In trial 1, herbage was (1) chopped with a paper-cutting guillotine into 5-10 mm lengths, representing fresh (FR) herbage; ...

Soybean and lactose in meat products and preparations sampled at retail

Directory of Open Access Journals (Sweden)

Filomena Piccolo

2016-06-01

Full Text Available Food allergies and intolerances have increased during the last decades and regulatory authorities have taken different measures to prevent and manage consumers’ adverse reactions, including correct labelling of foods. Aim of this work was to search for soybean and lactose in meat products and meat preparations taken from retail in some provinces of Campania Region (Southern Italy and to evaluate the food labels compliance with Regulation (EU n.1169/2011. Soybean and lactose were searched using commercial kits in n. 58 samples of meat products produced in or distributed by 19 establishments, and in n. 55 samples of meat products and n. 8 of meat preparations produced in 21 plants. All samples were selected on the basis of the absence of any information on the labels about the presence of the two searched allergens, with the exception of n. 5 samples tested for lactose. Traces of soybean were detected in 50 out of the 58 examined samples, at concentrations up to 0.93 mg kg–1. Only two samples contained levels above the detection limit of 0.31 mg kg–1. Lactose levels ranging from 0.11 to 2.95 g/100 g, i.e. above the detection limit, were found in all the tested samples (n. 63. The results of the present research underline the need for careful controls and planning by operators as part of the self-control plans, and deserve attention from the competent authorities considering not only the consumers’ health but also the great attention media pay to regulations providing consumers with information on food.

42 CFR 447.506 - Authorized generic drugs.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Authorized generic drugs. 447.506 Section 447.506... (CONTINUED) MEDICAL ASSISTANCE PROGRAMS PAYMENTS FOR SERVICES Payment for Drugs § 447.506 Authorized generic drugs. (a) Authorized generic drug defined. For the purposes of this subpart, an authorized generic drug...

Influence of sample preparation on the microstructure of tooth enamel apatite

Czech Academy of Sciences Publication Activity Database

Kallistová, Anna; Skála, Roman; Horáček, I.; Miyajima, N.; Malíková, R.

2015-01-01

Roč. 48, č. 3 (2015), s. 763-768 ISSN 0021-8898 Institutional support: RVO:67985831 Keywords : X-ray powder diffraction * sample preparation * microstructure * dental hydroxyapatite Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.720, year: 2014

Generic phytosanitary irradiation treatments

International Nuclear Information System (INIS)

Hallman, Guy J.

2012-01-01

The history of the development of generic phytosanitary irradiation (PI) treatments is discussed beginning with its initial proposal in 1986. Generic PI treatments in use today are 150 Gy for all hosts of Tephritidae, 250 Gy for all arthropods on mango and papaya shipped from Australia to New Zealand, 300 Gy for all arthropods on mango shipped from Australia to Malaysia, 350 Gy for all arthropods on lychee shipped from Australia to New Zealand and 400 Gy for all hosts of insects other than pupae and adult Lepidoptera shipped to the United States. Efforts to develop additional generic PI treatments and reduce the dose for the 400 Gy treatment are ongoing with a broad based 5-year, 12-nation cooperative research project coordinated by the joint Food and Agricultural Organization/International Atomic Energy Agency Program on Nuclear Techniques in Food and Agriculture. Key groups identified for further development of generic PI treatments are Lepidoptera (eggs and larvae), mealybugs and scale insects. A dose of 250 Gy may suffice for these three groups plus others, such as thrips, weevils and whiteflies. - Highlights: ► The history of phytosanitary irradiation (PI) treatments is given. ► Generic PI treatments in use today are discussed. ► Suggestions for future research are presented. ► A dose of 250 Gy for most insects may suffice.

Comparison of two sample preparation procedures for HPLC determination of ochratoxin A

Directory of Open Access Journals (Sweden)

Vuković Gorica L.

2009-01-01

Full Text Available In preparation of samples for chromatographic determination of ochratoxin A, two types of columns were used for sample cleanup (SPE and immunoaffinity columns. The first method consisted of liquid-liquid extraction with a mixture of chloroform and phosphoric acid, followed by ion-exchange cleanup on Waters Oasis MAX columns. The sec­ond method consisted of extraction with a mixture of water and methanol, followed by LCTech OtaCLEAN immunoaf­finity column cleanup. Recoveries of the methods were determined at three levels in three repetitions for maize flour, and they were 84% (%RSD = 19.2 for the first method of sample preparation and 101% (%RSD = 2.2 for the second method. Values of LOQ for OTA were 0.25 and 1.00 μg/kg for the IAC and SPE clean-up procedures, respectively. Both methods comply with present regulations, but the MAX sample clean-up procedure should be used as an alternative, since the immunoaffinity column clean-up procedure is characterized by better reproducibility, accuracy, and efficiency.

An electrodeposition method for the preparation of actinides and Ra samples for α spectrometry

International Nuclear Information System (INIS)

Garcia-Tenorio, R.; Garcia-Leon, M.; Madurga, G.; Piazza, C.

1986-01-01

As it is confirmed in this work, electrodeposition of α radionuclides gives a simple method for preparing α samples of high spectrometric quality, compared to those prepared by evaporation. Then we give the methods for electrodepositon or α emitters use in our Department. Actinides α emitters are electroplated from a 1% H 2 SO 4 medium with a recovery of about 90%. The samples of Ra are prepared by electrodeposition from a HCl + CH 3 -COONH 4 medium at pH approx.= 5. In this case the recovery reaches a value that ranges from 70 to 90%. For these measurements a Si surface barrier detector has been used. Some of its features are discussed in the text. (author)

On the preparation of as-produced and purified single-walled carbon nanotube samples for standardized X-ray diffraction characterization

International Nuclear Information System (INIS)

Allaf, Rula M.; Rivero, Iris V.; Spearman, Shayla S.; Hope-Weeks, Louisa J.

2011-01-01

The aim of this research was to specify proper sample conditioning for acquiring representative X-ray diffraction (XRD) profiles for single-walled carbon nanotube (SWCNT) samples. In doing so, a specimen preparation method for quantitative XRD characterization of as-produced and purified arc-discharge SWCNT samples has been identified. Series of powder XRD profiles were collected at different temperatures, states, and points of time to establish appropriate conditions for acquiring XRD profiles without inducing much change to the specimen. It was concluded that heating in the 300-450 deg. C range for 20 minutes, preferably vacuum-assisted, and then sealing the sample is an appropriate XRD specimen preparation technique for purified arc-discharge SWCNT samples, while raw samples do not require preconditioning for characterization. - Graphical Abstract: A sample preparation method for XRD characterization of as-produced and purified arc-discharge SWCNT samples is identified. The preparation technique seeks to acquire representative XRD profiles without inducing changes to the samples. Purified samples required 20 minutes of heating at (300-450)deg. C, while raw samples did not require preconditioning for characterization. Highlights: → Purification routines may induce adsorption onto the SWCNT samples. → Heating a SWCNT sample may result in material loss, desorption, and SWCNTs closing. → Raw arc-discharge samples do not require preparation for XRD characterization. → Heating is appropriate specimen preparation for purified and heat-treated samples. → XRD data fitting is required for structural analysis of SWCNT bundles.

Determinants of generic drug substitution in Switzerland

Directory of Open Access Journals (Sweden)

Lufkin Thomas M

2011-01-01

Full Text Available Abstract Background Since generic drugs have the same therapeutic effect as the original formulation but at generally lower costs, their use should be more heavily promoted. However, a considerable number of barriers to their wider use have been observed in many countries. The present study examines the influence of patients, physicians and certain characteristics of the generics' market on generic substitution in Switzerland. Methods We used reimbursement claims' data submitted to a large health insurer by insured individuals living in one of Switzerland's three linguistic regions during 2003. All dispensed drugs studied here were substitutable. The outcome (use of a generic or not was modelled by logistic regression, adjusted for patients' characteristics (gender, age, treatment complexity, substitution groups and with several variables describing reimbursement incentives (deductible, co-payments and the generics' market (prices, packaging, co-branded original, number of available generics, etc.. Results The overall generics' substitution rate for 173,212 dispensed prescriptions was 31%, though this varied considerably across cantons. Poor health status (older patients, complex treatments was associated with lower generic use. Higher rates were associated with higher out-of-pocket costs, greater price differences between the original and the generic, and with the number of generics on the market, while reformulation and repackaging were associated with lower rates. The substitution rate was 13% lower among hospital physicians. The adoption of the prescribing practices of the canton with the highest substitution rate would increase substitution in other cantons to as much as 26%. Conclusions Patient health status explained a part of the reluctance to substitute an original formulation by a generic. Economic incentives were efficient, but with a moderate global effect. The huge interregional differences indicated that prescribing behaviours and

Generic clearance values

International Nuclear Information System (INIS)

Bossio, M.C.; Muniz, C.C.

2009-01-01

This paper analyzes the Generic Clearance Values established for natural and artificial radionuclides with the objective of evaluating their degree of conservatism in views of adopting them into the regulatory body. Generic clearance values for natural radionuclides have been chosen by experts judgments as the optimum boundary between, on one hand, the ubiquitous unmodified soil concentrations and, on the other hand, activity concentrations in ores, mineral sands, industrial residues and wastes. For artificial radionuclides the clearance levels have been derived from the scenarios postulated in the document 'Safety Reports Series Nr 44' of the IAEA considering quantitative exemption criteria. A set of 8 scenarios were postulated covering external, ingestion and inhalation exposure pathways. For each radionuclide, the generic clearance level was derived as the more restrictive value obtained from the scenarios, that is the lowest ratio between the applicable individual dose and the dose per unit activity concentration (Bq/g). The individual dose was calculated by a formula depending on each scenario and pathway, with different parameters, such as exposure time, dosimetric factors, dilution factor, density of the material, geometric factors, etc. It was concluded that the basis and parameters used for the derivation of the generic clearance levels are quite conservative and therefore its the adoption in Argentina has been recommended. It is expected that their implementation will contribute to optimize the regulatory management system. (author)

Generic Clearance Values

International Nuclear Information System (INIS)

Bossio, M.C.; Muniz, C.C.

2010-01-01

This paper analyzes the Generic Clearance Values established for natural and artificial radionuclides with the objective of evaluating their degree of conservatism in views of adopting them into the regulatory body. Generic clearance values for natural radionuclides have been chosen by experts judgments as the optimum boundary between, on the one hand, the ubiquitous unmodified soil concentrations and, on the other hand, activity concentrations in ores, mineral sands, industrial residues and wastes. For artificial radionuclides the clearance levels have been derived from the scenarios postulated in the document Safety Reports Series 44 of the IAEA considering quantitative exemption criteria. A set of 8 scenarios were postulated covering external, ingestion and inhalation exposure pathways. For each radionuclide, the generic clearance level was derived as the more restrictive value obtained from the scenarios, that is the lowest ratio between the applicable individual dose and the dose per unit activity concentration (Bq/g). The individual dose was calculated by a formula depending on each scenario and pathway, with different parameters, such as exposure time, dosimetric factors, dilution factor, density of the material, geometric factors, etc. It was concluded that the basis and parameters used for the derivation of the generic clearance levels are quite conservative and therefore its the adoption in Argentina has been recommended. It is expected that their implementation will contribute to optimize the regulatory management system. (authors) [es

A generic method for the determination of acrylamide in thermally processed foods.

Science.gov (United States)

Gökmen, Vural; Senyuva, Hamide Z

2006-07-07

A generic sample preparation method for the determination of acrylamide in foods was developed. The method entails extraction with methanol, purification with Carrez I and II solutions, evaporation and solvent change to water, and cleanup with Oasis HLB solid-phase extraction (SPE) cartridge. The final extract was analyzed by liquid chromatography-mass spectrometry (LC-MS) for quantitation. The chromatographic separation was performed on ODS-3 column using the isocratic mixture of 0.01 mM acetic acid in 0.2% aqueous solution of formic acid at a flow rate of 0.6 ml/min at 25 degrees C. The recoveries of acrylamide from potato chips, biscuits and coffee ranged between 92.8 and 101.5% with relative standard deviations of 4.1% or less. The limit of detection (LOD) and the limit of quantitation (LOQ) were 2 ng/g and 6 ng/g in the basis of signal to noise ratios of 3:1 and 9:1, respectively.

Validation of a fully automated robotic setup for preparation of whole blood samples for LC-MS toxicology analysis

DEFF Research Database (Denmark)

Andersen, David Wederkinck; Rasmussen, Brian; Linnet, Kristian

2012-01-01

A fully automated setup was developed for preparing whole blood samples using a Tecan Evo workstation. By integrating several add-ons to the robotic platform, the flexible setup was able to prepare samples from sample tubes to a 96-well sample plate ready for injection on liquid chromatography...

Generic phytosanitary irradiation treatments

Energy Technology Data Exchange (ETDEWEB)

Hallman, Guy J [United States Department of Agriculture, Agricultural Research Service, Weslaco, TX (United States)

2013-01-15

The history of the development of generic phytosanitary irradiation (PI) treatments is discussed beginning with its initial proposal in 1986. Generic PI treatments in use today are 150 Gy for all hosts of Tephritidae, 250 Gy for all arthropods on mango and papaya shipped from Australia to New Zealand, 300 Gy for all arthropods on mango shipped from Australia to Malaysia, 350 Gy for all arthropods on lychee shipped from Australia to New Zealand and 400 Gy for all hosts of insects other than pupae and adult Lepidoptera shipped to the United States. Efforts to develop additional generic PI treatments and reduce the dose for the 400 Gy treatment are ongoing with a broad based 5-year, 12-nation cooperative research project coordinated by the joint Food and Agricultural Organization/International Atomic Energy Agency Program on Nuclear Techniques in Food and Agriculture. Key groups identified for further development of generic PI treatments are Lepidoptera (eggs and larvae), mealybugs and scale insects. A dose of 250 Gy may suffice for these three groups plus others, such as thrips, weevils and whiteflies. (author)

Generic phytosanitary irradiation treatments

Science.gov (United States)

Hallman, Guy J.

2012-07-01

The history of the development of generic phytosanitary irradiation (PI) treatments is discussed beginning with its initial proposal in 1986. Generic PI treatments in use today are 150 Gy for all hosts of Tephritidae, 250 Gy for all arthropods on mango and papaya shipped from Australia to New Zealand, 300 Gy for all arthropods on mango shipped from Australia to Malaysia, 350 Gy for all arthropods on lychee shipped from Australia to New Zealand and 400 Gy for all hosts of insects other than pupae and adult Lepidoptera shipped to the United States. Efforts to develop additional generic PI treatments and reduce the dose for the 400 Gy treatment are ongoing with a broad based 5-year, 12-nation cooperative research project coordinated by the joint Food and Agricultural Organization/International Atomic Energy Agency Program on Nuclear Techniques in Food and Agriculture. Key groups identified for further development of generic PI treatments are Lepidoptera (eggs and larvae), mealybugs and scale insects. A dose of 250 Gy may suffice for these three groups plus others, such as thrips, weevils and whiteflies.

76 FR 43353 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-07-20

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... and opinions, but are not statistical surveys that yield quantitative results that can be generalized...

76 FR 10626 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-02-25

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The..., but are not statistical surveys that yield quantitative results that can be [[Page 10627

78 FR 26087 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2013-05-03

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... and opinions, but are not statistical surveys that yield quantitative results that can be generalized...

76 FR 13338 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-03-11

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... and opinions, but are not statistical surveys that yield quantitative results that can be generalized...

76 FR 55078 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-09-06

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... and opinions, but are not statistical surveys that yield quantitative results that can be generalized...

76 FR 74802 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-12-01

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. No... perceptions and opinions, but are not statistical surveys that yield quantitative results that can be...

76 FR 20714 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-04-13

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... perceptions and opinions, but are not statistical surveys that yield quantitative results that can be...

Generic Advantages

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. Generic Advantages. Scalability an incremental coverage. Standardization. Business Plan Flexibility. Lifecycle Flexibility. Reliability. Service Interoperability. Changed Industry dynamics.

A sample preparation method for recovering suppressed analyte ions in MALDI TOF MS

NARCIS (Netherlands)

Lou, X.; Waal, de B.F.M.; Milroy, L.G.; Dongen, van J.L.J.

2015-01-01

In matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI TOF MS), analyte signals can be substantially suppressed by other compounds in the sample. In this technical note, we describe a modified thin-layer sample preparation method that significantly reduces the analyte

Implementation of antimicrobial peptides for sample preparation prior to nucleic acid amplification in point-of-care settings.

Science.gov (United States)

Krõlov, Katrin; Uusna, Julia; Grellier, Tiia; Andresen, Liis; Jevtuševskaja, Jekaterina; Tulp, Indrek; Langel, Ülo

2017-12-01

A variety of sample preparation techniques are used prior to nucleic acid amplification. However, their efficiency is not always sufficient and nucleic acid purification remains the preferred method for template preparation. Purification is difficult and costly to apply in point-of-care (POC) settings and there is a strong need for more robust, rapid, and efficient biological sample preparation techniques in molecular diagnostics. Here, the authors applied antimicrobial peptides (AMPs) for urine sample preparation prior to isothermal loop-mediated amplification (LAMP). AMPs bind to many microorganisms such as bacteria, fungi, protozoa and viruses causing disruption of their membrane integrity and facilitate nucleic acid release. The authors show that incubation of E. coli with antimicrobial peptide cecropin P1 for 5 min had a significant effect on the availability of template DNA compared with untreated or even heat treated samples resulting in up to six times increase of the amplification efficiency. These results show that AMPs treatment is a very efficient sample preparation technique that is suitable for application prior to nucleic acid amplification directly within biological samples. Furthermore, the entire process of AMPs treatment was performed at room temperature for 5 min thereby making it a good candidate for use in POC applications.

Evaluation of sample preparation protocols for spider venom profiling by MALDI-TOF MS.

Science.gov (United States)

Bočánek, Ondřej; Šedo, Ondrej; Pekár, Stano; Zdráhal, Zbyněk

2017-07-01

Spider venoms are highly complex mixtures containing biologically active substances with potential for use in biotechnology or pharmacology. Fingerprinting of venoms by Matrix-Assisted Laser Desorption-Ionization - Time of Flight Mass Spectrometry (MALDI-TOF MS) is a thriving technology, enabling the rapid detection of peptide/protein components that can provide comparative information. In this study, we evaluated the effects of sample preparation procedures on MALDI-TOF mass spectral quality to establish a protocol providing the most reliable analytical outputs. We adopted initial sample preparation conditions from studies already published in this field. Three different MALDI matrixes, three matrix solvents, two sample deposition methods, and different acid concentrations were tested. As a model sample, venom from Brachypelma albopilosa was used. The mass spectra were evaluated on the basis of absolute and relative signal intensities, and signal resolution. By conducting three series of analyses at three weekly intervals, the reproducibility of the mass spectra were assessed as a crucial factor in the selection for optimum conditions. A sample preparation protocol based on the use of an HCCA matrix dissolved in 50% acetonitrile with 2.5% TFA deposited onto the target by the dried-droplet method was found to provide the best results in terms of information yield and repeatability. We propose that this protocol should be followed as a standard procedure, enabling the comparative assessment of MALDI-TOF MS spider venom fingerprints. Copyright © 2017 Elsevier Ltd. All rights reserved.

Generic penetration in the retail antidepressant market.

Science.gov (United States)

Ventimiglia, Jeffrey; Kalali, Amir H

2010-06-01

In this article, we explore the accelerated penetration of generic antidepressants in the United States market following the availability of generic citalopram and sertraline. Analysis suggests that overall, generic penetration into the antidepressant market has grown from approximately 41 percent in January 2004 to over 73 percent in January 2010. Similar trends are uncovered when branded and generic prescriptions are analyzed by specialty.

Challenges of sample preparation for cross sectional EBSD analysis of electrodeposited nickel films

DEFF Research Database (Denmark)

Alimadadi, Hossein; Pantleon, Karen

2009-01-01

Thorough microstructure and crystallographic orientation analysis of thin films by means of electron backscatter diffraction requires cross section preparation of the film-substrate compound. During careful preparation, changes of the rather non-stable as-deposited microstructure must be avoided....... Different procedures for sample preparation including mechanical grinding and polishing, electropolishing and focused ion beam milling have been applied to a nickel film electrodeposited on top of an amorphous Ni-P layer on a Cu-substrate. Reliable EBSD analysis of the whole cross section can be obtained...

Transmission Electron Microscopy (TEM) Sample Preparation of Si(1-x)Gex in c-Plane Sapphire Substrate

Science.gov (United States)

Kim, Hyun Jung; Choi, Sang H.; Bae, Hyung-Bin; Lee, Tae Woo

2012-01-01

The National Aeronautics and Space Administration-invented X-ray diffraction (XRD) methods, including the total defect density measurement method and the spatial wafer mapping method, have confirmed super hetero epitaxy growth for rhombohedral single crystalline silicon germanium (Si1-xGex) on a c-plane sapphire substrate. However, the XRD method cannot observe the surface morphology or roughness because of the method s limited resolution. Therefore the authors used transmission electron microscopy (TEM) with samples prepared in two ways, the focused ion beam (FIB) method and the tripod method to study the structure between Si1-xGex and sapphire substrate and Si1?xGex itself. The sample preparation for TEM should be as fast as possible so that the sample should contain few or no artifacts induced by the preparation. The standard sample preparation method of mechanical polishing often requires a relatively long ion milling time (several hours), which increases the probability of inducing defects into the sample. The TEM sampling of the Si1-xGex on sapphire is also difficult because of the sapphire s high hardness and mechanical instability. The FIB method and the tripod method eliminate both problems when performing a cross-section TEM sampling of Si1-xGex on c-plane sapphire, which shows the surface morphology, the interface between film and substrate, and the crystal structure of the film. This paper explains the FIB sampling method and the tripod sampling method, and why sampling Si1-xGex, on a sapphire substrate with TEM, is necessary.

Molecularly imprinted polymers for sample preparation and biosensing in food analysis: Progress and perspectives

DEFF Research Database (Denmark)

Ashley, Jon; Shahbazi, Mohammad-Ali; Kant, Krishna

2017-01-01

Molecularly imprinted polymers (MIPs) are biomimetics which can selectively bind to analytes of interest. One of the most interesting areas where MIPs have shown the biggest potential is food analysis. MIPs have found use as sorbents in sample preparation attributed to the high selectivity and high...... the imprinting methods which are applicable for imprinting food templates, summarize the recent progress in using MIPs for preparing and analysing food samples, and discuss the current limitations in the commercialisation of MIPs technology. Finally, future perspectives will be given....

[Bioequivalence studies of pharmaceutical preparations].

Science.gov (United States)

Vetchý, D; Frýbortová, K; Rabisková, M; Danecková, H

2007-01-01

Bioequivalence studies are very important for the development of a pharmaceutical preparation in the pharmaceutical industry. Their rationale is the monitoring of pharmacokinetic and pharmacodynamic parameters after the administration of tested drugs. The target of such study is to evaluate the therapeutic compatibility of tested drugs (pharmaceutical equivalents or pharmaceutical alternatives). The importance of bioequivalence studies is increasing also due to the large growth of the production and consumption of generic products. Generic products represent approximately 50 % of the whole consumption in many European countries and USA. The search output of bioequivalence study is together with the pharmaceutical quality data of medical product one of the main part of the registration file submitted to a national regulatory authorities. The registration of generic products does not demand complicated and expensive clinical study contrary to original product. The comparison of the original and the generic product via bioequivalence study is suggested as sufficient. The aim of this article is to provide to a medical public a summary about the types of bioequivalence studies, their range, rules of their practise and let them gain their own attitude to this question.

An On-Target Desalting and Concentration Sample Preparation Protocol for MALDI-MS and MS/MS Analysis

DEFF Research Database (Denmark)

Zhang, Xumin; Wang, Quanhui; Lou, Xiaomin

2012-01-01

2DE coupled with MALDI-MS is one of the most widely used and powerful analytic technologies in proteomics study. The MALDI sample preparation method has been developed and optimized towards the combination of simplicity, sample-cleaning, and sample concentration since its introduction. Here we...... present a protocol of the so-called Sample loading, Matrix loading, and on-target Wash (SMW) method which fulfills the three criteria by taking advantage of the AnchorChip™ targets. Our method is extremely simple and no pre-desalting or concentration is needed when dealing with samples prepared from 2DE...

Addition of generic medication vouchers to a pharmacist academic detailing program: effects on the generic dispensing ratio in a physician-hospital organization.

Science.gov (United States)

Bhargava, Vinay; Greg, Mark E; Shields, Mark C

2010-01-01

Generic dispensing ratio (GDR) is an important measure of efficiency in pharmacy benefit management. A few studies have examined the effects of academic detailing or generic drug samples on GDR. On July 1, 2007, a physician-hospital organization (PHO) with a pay-for-performance incentive for generic utilization initiated a pilot generic medication voucher program that augmented its existing pharmacist-led academic detailing efforts. No published studies have examined the role of generic medication vouchers in promoting generic drug utilization. To determine if supplementing an existing academic detailing initiative in a PHO with a generic medication voucher program would be more effective in increasing the GDR compared with academic detailing alone. The intervention took place over the 9-month period from July 1, 2007, through March 31, 2008. Vouchers provided patients with the first fill of a 30-day supply of a generic drug at no cost to the patient for 8 specific generic medications obtained through a national community pharmacy chain. The study was conducted in a PHO composed of 7 hospitals and approximately 2,900 physicians (900 primary care providers [PCPs] and 2,000 specialists). Of the approximately 300 PCP practices, 21 practices with at least 2 physicians each were selected on the basis of high prescription volume (more than 500 pharmacy claims for the practice over a 12-month pre-baseline period) and low GDR (practice GDR less than 55% in the 12-month pre-baseline period). These 21 practices were then randomized to a control group of academic detailing alone or the intervention group that received academic detailing plus generic medication vouchers. One of 10 intervention groups declined to participate, and 2 of 11 control groups dropped out of the PHO. GDR was calculated monthly for all pharmacy claims including the 8 voucher medications. GDR was defined as the ratio of the total number of paid generic pharmacy claims divided by the total number of paid

77 FR 3272 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2012-01-23

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. No... opinions, but are not statistical surveys that yield quantitative results that can be generalized to the...

76 FR 70460 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-11-14

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... opinions, but are not statistical surveys that yield quantitative results that can be generalized to the...

76 FR 17182 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-03-28

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The FAA..., but are not statistical surveys that yield quantitative results that can be generalized to the...

76 FR 40981 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-07-12

... target population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. On... insights on perceptions and opinions, but are not statistical surveys that yield quantitative results that...

76 FR 45573 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-07-29

... target population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... insights on perceptions and opinions, but are not statistical surveys that yield quantitative results that...

78 FR 44133 - Agency Information Collection Activities; Proposed Collection; Comment Request: Generic Clearance...

Science.gov (United States)

2013-07-23

... target population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. No... insights on perceptions and opinions, but are not statistical surveys that yield quantitative results that...

76 FR 13436 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-03-11

... target population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The MSPB... insights on perceptions and opinions, but are not statistical surveys that yield quantitative results that...

76 FR 22937 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-04-25

... population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The... opinions, but are not statistical surveys that yield quantitative results that can be generalized to the...

76 FR 19359 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-04-07

... population to which generalizations will be made, the sampling frame, the sample design (including... still be eligible for submission for other generic mechanisms that are designed to yield quantitative..., but are not statistical surveys that yield quantitative results that can be generalized to the...

Generic nano-imprint process for fabrication of nanowire arrays

Energy Technology Data Exchange (ETDEWEB)

Pierret, Aurelie; Hocevar, Moira; Algra, Rienk E; Timmering, Eugene C; Verschuuren, Marc A; Immink, George W G; Verheijen, Marcel A; Bakkers, Erik P A M [Philips Research Laboratories Eindhoven, High Tech Campus 11, 5656 AE Eindhoven (Netherlands); Diedenhofen, Silke L [FOM Institute for Atomic and Molecular Physics c/o Philips Research Laboratories, High Tech Campus 4, 5656 AE Eindhoven (Netherlands); Vlieg, E, E-mail: e.p.a.m.bakkers@tue.nl [IMM, Solid State Chemistry, Radboud University Nijmegen, Heyendaalseweg 135, 6525 AJ Nijmegen (Netherlands)

2010-02-10

A generic process has been developed to grow nearly defect-free arrays of (heterostructured) InP and GaP nanowires. Soft nano-imprint lithography has been used to pattern gold particle arrays on full 2 inch substrates. After lift-off organic residues remain on the surface, which induce the growth of additional undesired nanowires. We show that cleaning of the samples before growth with piranha solution in combination with a thermal anneal at 550 deg. C for InP and 700 deg. C for GaP results in uniform nanowire arrays with 1% variation in nanowire length, and without undesired extra nanowires. Our chemical cleaning procedure is applicable to other lithographic techniques such as e-beam lithography, and therefore represents a generic process.

A comparison of sample preparation strategies for biological tissues and subsequent trace element analysis using LA-ICP-MS.

Science.gov (United States)

Bonta, Maximilian; Török, Szilvia; Hegedus, Balazs; Döme, Balazs; Limbeck, Andreas

2017-03-01

Laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) is one of the most commonly applied methods for lateral trace element distribution analysis in medical studies. Many improvements of the technique regarding quantification and achievable lateral resolution have been achieved in the last years. Nevertheless, sample preparation is also of major importance and the optimal sample preparation strategy still has not been defined. While conventional histology knows a number of sample pre-treatment strategies, little is known about the effect of these approaches on the lateral distributions of elements and/or their quantities in tissues. The technique of formalin fixation and paraffin embedding (FFPE) has emerged as the gold standard in tissue preparation. However, the potential use for elemental distribution studies is questionable due to a large number of sample preparation steps. In this work, LA-ICP-MS was used to examine the applicability of the FFPE sample preparation approach for elemental distribution studies. Qualitative elemental distributions as well as quantitative concentrations in cryo-cut tissues as well as FFPE samples were compared. Results showed that some metals (especially Na and K) are severely affected by the FFPE process, whereas others (e.g., Mn, Ni) are less influenced. Based on these results, a general recommendation can be given: FFPE samples are completely unsuitable for the analysis of alkaline metals. When analyzing transition metals, FFPE samples can give comparable results to snap-frozen tissues. Graphical abstract Sample preparation strategies for biological tissues are compared with regard to the elemental distributions and average trace element concentrations.

Development and optimisation of generic decommissioning strategies for civil Magnox reactors

International Nuclear Information System (INIS)

Carpenter, G.; Hebditch, D.; Meek, N.; Patel, A.; Reeve, P.

2004-01-01

BNFL Environmental Services has formulated updated proposals for the use of decision analysis in the development of decommissioning strategy. The proposals are based on the Department of Transport, Local Government and the Regions manual for practitioners on multi-criteria analysis, specifically multi-criteria decision analysis, as suited to complex problems with a mixture of monetary and non-monetary objectives. They take account of up-to-date academic methodology, the newly issued BNFL decision analysis framework for environmental decisions and a wide variety of other engineering, optioneering and optimisation processes. The paper also summarises legislative and company policy areas of importance to decommissioning strategy development. Higher-level generic reactor and site remediation strategies already exist. At the lower level, various generic decommissioning reference processes and project options need development. For the past year, Environmental Services has held responsibility to respond to the Nuclear Installations Inspectorates' quinquennial review, develop and maintain up-to-date strategies, institute the review of a selected number of key strategies, and respond to changing circumstances including stakeholder views. Environmental Services is performing a range of generic studies for selection of strategies and end-points as used for a variety of waste management and site care and maintenance preparations. (author)

Atomic absorption determination of metals in soils using ultrasonic sample preparation

International Nuclear Information System (INIS)

Chmilenko, F.A.; Smityuk, N.M.; Baklanov, A.N.

2002-01-01

It was shown that ultrasonic treatment accelerates sample preparation of soil extracts from chernozem into different solvents by a factor of 6 to 60. These extracts are used for the atomic absorption determination of soluble species of Cd, Co, Cr, Cu, Ni, Pb, and Zn. The optimum ultrasound parameters (frequency, intensity, and treatment time) were found for preparing soil extracts containing analytes in concentrations required in agrochemical procedures. Different extractants used to extract soluble heavy metals from soils of an ordinary chernozem type in agrochemical procedures using ultrasonic treatment were classified in accordance with the element nature [ru

9 CFR 147.8 - Procedures for preparing egg yolk samples for diagnostic tests.

Science.gov (United States)

2010-01-01

... samples for diagnostic tests. 147.8 Section 147.8 Animals and Animal Products ANIMAL AND PLANT HEALTH... IMPROVEMENT PLAN Blood Testing Procedures § 147.8 Procedures for preparing egg yolk samples for diagnostic... for diagnostic testing. (b) The authorized laboratory must identify each egg as to the breeding flock...

Interventions promoting the acceptance and uptake of generic medicines: a narrative review of the literature.

Science.gov (United States)

Babar, Z U D; Kan, S W; Scahill, S

2014-09-01

The objective of this paper was to undertake a narrative review of the literature regarding strategies and interventions promoting the acceptance and uptake of generic medicines. A literature search was performed between November 2011 and January 2012 to identify published full text original research articles documenting interventions to promote the use of generic medicines. Keywords used were: "generic medicine", "generic drug", "intervention", "promotion", "acceptance", "uptake", "generic/therapeutic substitution" and their related root words. The electronic databases comprised of Embase (1980 - present), Google, Google Scholar, Medline (1948 - present), PubMed, Science Direct, Scopus, Springer Link and The Cochrane Library. An interpretative narrative synthesis was undertaken and emergent themes analysed and reported. Eighteen studies were included in the final analysis. There were seven main themes which including; education, financial incentives, advertising to promote generic medicines, free generic medicine trials, administrative forms and medicines use review (MUR). These themes were further classified into subthemes. Education was subdivided into consumer and physician education. Financial incentives included the influence of financial incentives on both consumers and physicians. The subthemes in the financial incentives category included the changes in co-payment for consumers, reward payment for physicians and fund-holding schemes. Advertising included the sub-themes of print media and the use of anthropomorphic images, while free generic medicines trial was made up of free vouchers for generic medicines and generic medicines sampling system. The studies have mixed results; some interventions in some settings were useful, while others were not. Not all interventions consistently improved the uptake of generic medicines. There was limited literature available and further work is required to develop a range of interventions to support the uptake of generic

Analytical sample preparation strategies for the determination of antimalarial drugs in human whole blood, plasma and urine

DEFF Research Database (Denmark)

Casas, Monica Escolà; Hansen, Martin; Krogh, Kristine A

2014-01-01

the available sample preparation strategies combined with liquid chromatographic (LC) analysis to determine antimalarials in whole blood, plasma and urine published over the last decade. Sample preparation can be done by protein precipitation, solid-phase extraction, liquid-liquid extraction or dilution. After...

Rethinking generic skills

Directory of Open Access Journals (Sweden)

Roy Canning

2013-10-01

Full Text Available The paper provides a critical analysis of the notion of generic or transversal skillscontained with European Union policy discourses. The author presents a conceptualframework that challenges the idea that generic skills are universal, transferable andautonomous. An alternative analysis is put forward that argues the case forcontextualising skills and knowledge within particular understandings and cultures thatare more collective than individualistic in nature. The arguments are framed withinwider cross-disciplinary debates in linguistics, geosemiotics and social-cultural theoryand build upon an earlier paper exploring core skills in the UK (Canning, 2007.

A Simple and Reproducible Method to Prepare Membrane Samples from Freshly Isolated Rat Brain Microvessels.

Science.gov (United States)

Brzica, Hrvoje; Abdullahi, Wazir; Reilly, Bianca G; Ronaldson, Patrick T

2018-05-07

The blood-brain barrier (BBB) is a dynamic barrier tissue that responds to various pathophysiological and pharmacological stimuli. Such changes resulting from these stimuli can greatly modulate drug delivery to the brain and, by extension, cause considerable challenges in the treatment of central nervous system (CNS) diseases. Many BBB changes that affect pharmacotherapy, involve proteins that are localized and expressed at the level of endothelial cells. Indeed, such knowledge on BBB physiology in health and disease has sparked considerable interest in the study of these membrane proteins. From a basic science research standpoint, this implies a requirement for a simple but robust and reproducible method for isolation of microvessels from brain tissue harvested from experimental animals. In order to prepare membrane samples from freshly isolated microvessels, it is essential that sample preparations be enriched in endothelial cells but limited in the presence of other cell types of the neurovascular unit (i.e., astrocytes, microglia, neurons, pericytes). An added benefit is the ability to prepare samples from individual animals in order to capture the true variability of protein expression in an experimental population. In this manuscript, details regarding a method that is utilized for isolation of rat brain microvessels and preparation of membrane samples are provided. Microvessel enrichment, from samples derived, is achieved by using four centrifugation steps where dextran is included in the sample buffer. This protocol can easily be adapted by other laboratories for their own specific applications. Samples generated from this protocol have been shown to yield robust experimental data from protein analysis experiments that can greatly aid the understanding of BBB responses to physiological, pathophysiological, and pharmacological stimuli.

Improvement of a sample preparation method assisted by sodium deoxycholate for mass-spectrometry-based shotgun membrane proteomics.

Science.gov (United States)

Lin, Yong; Lin, Haiyan; Liu, Zhonghua; Wang, Kunbo; Yan, Yujun

2014-11-01

In current shotgun-proteomics-based biological discovery, the identification of membrane proteins is a challenge. This is especially true for integral membrane proteins due to their highly hydrophobic nature and low abundance. Thus, much effort has been directed at sample preparation strategies such as use of detergents, chaotropes, and organic solvents. We previously described a sample preparation method for shotgun membrane proteomics, the sodium deoxycholate assisted method, which cleverly circumvents many of the challenges associated with traditional sample preparation methods. However, the method is associated with significant sample loss due to the slightly weaker extraction/solubilization ability of sodium deoxycholate when it is used at relatively low concentrations such as 1%. Hence, we present an enhanced sodium deoxycholate sample preparation strategy that first uses a high concentration of sodium deoxycholate (5%) to lyse membranes and extract/solubilize hydrophobic membrane proteins, and then dilutes the detergent to 1% for a more efficient digestion. We then applied the improved method to shotgun analysis of proteins from rat liver membrane enriched fraction. Compared with other representative sample preparation strategies including our previous sodium deoxycholate assisted method, the enhanced sodium deoxycholate method exhibited superior sensitivity, coverage, and reliability for the identification of membrane proteins particularly those with high hydrophobicity and/or multiple transmembrane domains. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Quality of generic medicines in South Africa

DEFF Research Database (Denmark)

Patel, Aarti; Gauld, Robin; Norris, Pauline

2012-01-01

Generic Medicines are an important policy option allowing for access to affordable, essential medicines. Quality of generic medicines must be guaranteed through the activities of national medicines regulatory authorities. Existing negative perceptions surrounding the quality of generic medicines ...

76 FR 39893 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-07-07

... target population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. The U.S... and opinions, but does not yield quantitative data that can be generalized to the overall population...

76 FR 13698 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

Science.gov (United States)

2011-03-14

... target population to which generalizations will be made, the sampling frame, the sample design (including... for sub mission for other generic mechanisms that are designed to yield quantitative results. The... opinions, but are not statistical surveys that yield quantitative results that can be generalized to the...

M3FT-17OR0301070211 - Preparation of Hot Isostatically Pressed AgZ Waste Form Samples

Energy Technology Data Exchange (ETDEWEB)

Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jordan, Jacob A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-10-01

The production of radioactive iodine-bearing waste forms that exhibit long-term stability and are suitable for permanent geologic disposal has been the subject of substantial research interest. One potential method of iodine waste form production is hot isostatic pressing (HIP). Recent studies at Oak Ridge National Laboratory (ORNL) have investigated the conversion of iodine-loaded silver mordenite (I-AgZ) directly to a waste form by HIP. ORNL has performed HIP with a variety of sample compositions and pressing conditions. The base mineral has varied among AgZ (in pure and engineered forms), silver-exchanged faujasite, and silverexchanged zeolite A. Two iodine loading methods, occlusion and chemisorption, have been explored. Additionally, the effects of variations in temperature and pressure of the process have been examined, with temperature ranges of 525°C–1,100°C and pressure ranges of 100–300 MPa. All of these samples remain available to collaborators upon request. The sample preparation detailed in this document is an extension of that work. In addition to previously prepared samples, this report documents the preparation of additional samples to support stability testing. These samples include chemisorbed I-AgZ and pure AgI. Following sample preparation, each sample was processed by HIP by American Isostatic Presses Inc. and returned to ORNL for storage. ORNL will store the samples until they are requested by collaborators for durability testing. The sample set reported here will support waste form durability testing across the national laboratories and will provide insight into the effects of varied iodine content on iodine retention by the produced waste form and on potential improvements in waste form durability provided by the zeolite matrix.

Collection and preparation of marine samples for radionuclide analysis

International Nuclear Information System (INIS)

Holm, E.

1997-01-01

The ultimate goal of research in radioecology is to be able to predict the pathways of radioactive material in the environment and hence estimate possible doses to the population in various regions. Knowledge of levels of contamination are necessary to maintain control of operations of nuclear facilities. Correct methods of sample collection, handling and preparation are among the most important parts for a correct assessment. On basis of the final results of radionuclide concentrations, scientific, medical and political decisions are taken. (author)

Preparing Monodisperse Macromolecular Samples for Successful Biological Small-Angle X-ray and Neutron Scattering Experiments

Science.gov (United States)

Jeffries, Cy M.; Graewert, Melissa A.; Blanchet, Clément E.; Langley, David B.; Whitten, Andrew E.; Svergun, Dmitri I

2017-01-01

Small-angle X-ray and neutron scattering (SAXS and SANS) are techniques used to extract structural parameters and determine the overall structures and shapes of biological macromolecules, complexes and assemblies in solution. The scattering intensities measured from a sample contain contributions from all atoms within the illuminated sample volume including the solvent and buffer components as well as the macromolecules of interest. In order to obtain structural information, it is essential to prepare an exactly matched solvent blank so that background scattering contributions can be accurately subtracted from the sample scattering to obtain the net scattering from the macromolecules in the sample. In addition, sample heterogeneity caused by contaminants, aggregates, mismatched solvents, radiation damage or other factors can severely influence and complicate data analysis so it is essential that the samples are pure and monodisperse for the duration of the experiment. This Protocol outlines the basic physics of SAXS and SANS and reveals how the underlying conceptual principles of the techniques ultimately ‘translate’ into practical laboratory guidance for the production of samples of sufficiently high quality for scattering experiments. The procedure describes how to prepare and characterize protein and nucleic acid samples for both SAXS and SANS using gel electrophoresis, size exclusion chromatography and light scattering. Also included are procedures specific to X-rays (in-line size exclusion chromatography SAXS) and neutrons, specifically preparing samples for contrast matching/variation experiments and deuterium labeling of proteins. PMID:27711050

Quality of generic medicines in South Africa: Perceptions versus Reality – A qualitative study

Directory of Open Access Journals (Sweden)

Patel Aarti

2012-09-01

Full Text Available Abstract Background Generic Medicines are an important policy option allowing for access to affordable, essential medicines. Quality of generic medicines must be guaranteed through the activities of national medicines regulatory authorities. Existing negative perceptions surrounding the quality of generic medicines must be addressed to ensure that people use them with confidence. Campaigns to increase the uptake of generic medicines by consumers and providers of healthcare need to be informed by local norms and practices. This study sought to compare South African consumers’ and healthcare providers’ perceptions of quality of generics to the actual quality of selected products. Methods The study was conducted at the local level in three cities of South Africa: Johannesburg, Durban and Cape Town. Purposive sampling was used to recruit consumer participants (n = 73 and random sampling used to recruit healthcare providers from public and private sectors (n = 15. Data were obtained through twelve focus group discussions with consumers and semi-structured interviews (n = 15 with healthcare providers in order to gain familiarity with perceptions of quality. One hundred and thirty five products comprising paracetamol tablets (n = 47, amoxicillin capsules (n = 45 and hydrochlorothiazide tablets (n = 43 were sourced from public and private sector healthcare providers. These products were subjected to in vitro dissolution, uniformity of weight and identity (Fourier Transformed Infrared Spectroscopy tests using prescribed methods from the British (2005 and United States Pharmacopeias (2006. Results Respondents described drug quality in relation to the effect on symptoms. Procurement and use behavior of healthcare providers was influenced by prior experience, manufacturers’ names and consumers’ ability to pay. All formulations passed the in vitro tests for quality. Conclusions This study showed clear differences between

Exploring knowledge, perceptions and attitudes about generic ...

African Journals Online (AJOL)

Exploring knowledge, perceptions and attitudes about generic medicines among final-year health science students. ... had knowledge deficits about the safety, quality and efficacy of generic medicines. The dissemination of information about generic medicines may strengthen future knowledge, attitudes and perceptions.

Quantum process estimation via generic two-body correlations

International Nuclear Information System (INIS)

Mohseni, M.; Rezakhani, A. T.; Barreiro, J. T.; Kwiat, P. G.; Aspuru-Guzik, A.

2010-01-01

Performance of quantum process estimation is naturally limited by fundamental, random, and systematic imperfections of preparations and measurements. These imperfections may lead to considerable errors in the process reconstruction because standard data-analysis techniques usually presume ideal devices. Here, by utilizing generic auxiliary quantum or classical correlations, we provide a framework for the estimation of quantum dynamics via a single measurement apparatus. By construction, this approach can be applied to quantum tomography schemes with calibrated faulty-state generators and analyzers. Specifically, we present a generalization of the work begun by M. Mohseni and D. A. Lidar [Phys. Rev. Lett. 97, 170501 (2006)] with an imperfect Bell-state analyzer. We demonstrate that for several physically relevant noisy preparations and measurements, classical correlations and a small data-processing overhead suffice to accomplish the full system identification. Furthermore, we provide the optimal input states whereby the error amplification due to inversion of the measurement data is minimal.

Sulfonate-terminated carbosilane dendron-coated nanotubes: a greener point of view in protein sample preparation.

Science.gov (United States)

González-García, Estefanía; Gutiérrez Ulloa, Carlos E; de la Mata, Francisco Javier; Marina, María Luisa; García, María Concepción

2017-09-01

Reduction or removal of solvents and reagents in protein sample preparation is a requirement. Dendrimers can strongly interact with proteins and have great potential as a greener alternative to conventional methods used in protein sample preparation. This work proposes the use of single-walled carbon nanotubes (SWCNTs) functionalized with carbosilane dendrons with sulfonate groups for protein sample preparation and shows the successful application of the proposed methodology to extract proteins from a complex matrix. SEM images of nanotubes and mixtures of nanotubes and proteins were taken. Moreover, intrinsic fluorescence intensity of proteins was monitored to observe the most significant interactions at increasing dendron generations under neutral and basic pHs. Different conditions for the disruption of interactions between proteins and nanotubes after protein extraction and different concentrations of the disrupting reagent and the nanotube were also tried. Compatibility of extraction and disrupting conditions with the enzymatic digestion of proteins for obtaining bioactive peptides was also studied. Finally, sulfonate-terminated carbosilane dendron-coated SWCNTs enabled the extraction of proteins from a complex sample without using non-environmentally friendly solvents that were required so far. Graphical Abstract Green protein extraction from a complex sample employing carbosilane dendron coated nanotubes.

Knowledge, attitudes and practices of community pharmacists on generic medicines in Palestine: a cross-sectional study.

Science.gov (United States)

Shraim, Naser Y; Al Taha, Tasneem A; Qawasmeh, Rawan F; Jarrar, Hiba N; Shtaya, Maram A N; Shayeb, Lama A; Sweileh, Waleed M

2017-12-28

Generic substitution in several countries has become a common practice. Besides, it is considered as a major cost minimizing strategy meant to contain pharmaceutical expenditure without compromising healthcare quality. However, the safety and quality issues of generic products are of top concerns of general practitioners and health work professionals. This study aimed to investigate community pharmacist's knowledge, attitudes and practices toward generic medicines in Palestine. This study was a cross-sectional observational study employing a self-administered questionnaire. The questionnaire was of four main sections: demographic and practice details of the participants, knowledge, attitudes and the influencing factors related to selection and dispensing of generic medicines. A convenience sampling technique was implemented in this study in which the data collection form was distributed in West Bank- Palestine among a set of practicing pharmacists. Mann-Whitney-U or Kruskal-Wallis tests were used to comparison of different issues as appropriate. P-values of marketing approval of generics, while 87.4% of participants agreed that they should be given the right to substitute generics and the majority (62.3%) support generic substitution for brand name drugs in all cases when a generic is available The main two factors affect pharmacists' selection and dispensing of generic medicines are personal faith in the product (86.1%) and cost effectiveness of generic medicines (84.1%). Generic medicines substitution among pharmacists is widespread and prevalent. Our data found that participant pharmacists in Palestine had basic knowledge with regards to generic medicine. However, their knowledge score pertaining the technical and regulatory aspects of bioequivalence and pharmacokinetic parameters in particular was insufficient.

Generic medicines: solutions for a sustainable drug market?

Science.gov (United States)

Dylst, Pieter; Vulto, Arnold; Godman, Brian; Simoens, Steven

2013-10-01

Generic medicines offer equally high-quality treatment as originator medicines do at much lower prices. As such, they represent a considerable opportunity for authorities to obtain substantial savings. At the moment, the pharmaceutical landscape is changing and many pharmaceutical companies have altered their development and commercial strategies, combining both originator and generic divisions. In spite of this, the generic medicines industry is currently facing a number of challenges: delayed market access; the limited price differential with originator medicines; the continuous downwards pressure on prices; and the negative perception regarding generic medicines held by some key stakeholder groups. This could jeopardize the long-term sustainability of the generic manufacturing industry. Therefore, governments must focus on demand-side policies, alongside policies to accelerate market access, as the generic medicines industry will only be able to deliver competitive and sustainable prices if they are ensured a high volume. In the future, the generic medicines industry will increasingly look to biosimilars and generic versions of orphan drugs to expand their business.

Comparing approaches to generic programming in Haskell

NARCIS (Netherlands)

Hinze, R.; Jeuring, J.T.; Löh, A.

2006-01-01

The last decade has seen a number of approaches to generic programming: PolyP, Functorial ML, `Scrap Your Boilerplate', Generic Haskell, `Generics for the Masses', etc. The approaches vary in sophistication and target audience: some propose full-blown pro- gramming languages, some suggest

Generic Switching and Non-Persistence among Medicine Users

DEFF Research Database (Denmark)

Østergaard Rathe, Jette; Andersen, Morten; Jarbøl, Dorte Ejg

2015-01-01

BACKGROUND: Generic substitution means that one medicinal product is replaced by another product containing the same active substance. It is strictly regulated with respect to its bioequivalence, and all products must have undergone appropriate studies. Although generic substitution is widely...... implemented, it still remains to be answered how generic switch influences persistence to long-term treatment, and if it is modified by patients' concerns about medicine and views on generic medicine. This study focuses on users of antidepressants and antiepileptics, and their experience of generic switching....... METHODS: The study was an observational cohort study. By use of a prescription database, we identified patients who had redeemed prescriptions on generically substitutable drugs, and a questionnaire was mailed to them. We analyzed predictors of discontinuation in relation to generic switch and patients...

Article choice in plural generics

NARCIS (Netherlands)

Farkas, D.F.; Swart, Henriëtte de

2007-01-01

We discuss two groups of languages where article use contrasts in generic plural sentences but is otherwise essentially similar. The languages in the first group (English and Dutch) use bare plurals in the expression of kind reference (‘Dinosaurs are extinct’) and in generic

Preparation Of Deposited Sediment Sample By Casting Method For Environmental Study

International Nuclear Information System (INIS)

Hutabarat, Tommy; Ristin PI, Evarista

2000-01-01

The preparation of deposited sediment sample by c asting m ethod for environmental study has been carried out. This method comprises separation of size fraction and casting process. The deposited sediment samples were wet sieved to separate the size fraction of >500 mum, (250-500) mum, (125-250) mum and (63-125) mum and settling procedures were followed for the separation of (40-63) mum, (20-40) mum, (10-20) mum and o C, ashed at 450 o C, respectively. In the casting process of sample, it was used polyester rapid cure resin and methyl ethyl ketone peroxide (MEKP) hardener. The moulded sediment sample was poured onto caster, allow for 60 hours long. The aim of this method is to get the casted sample which can be used effectively, efficiently and to be avoided from contamination of each other samples. Before casting, samples were grinded up to be fine. The result shows that casting product is ready to be used for natural radionuclide analysis

40 CFR 721.9973 - Zirconium dichlorides (generic).

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Zirconium dichlorides (generic). 721... Substances § 721.9973 Zirconium dichlorides (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as zirconium dichlorides (PMNs P...

Comparing approaches to generic programming in Haskell

NARCIS (Netherlands)

Hinze, R.; Jeuring, J.T.; Löh, A.

2006-01-01

The last decade has seen a number of approaches to data- type-generic programming: PolyP, Functorial ML, `Scrap Your Boiler- plate', Generic Haskell, `Generics for the Masses', etc. The approaches vary in sophistication and target audience: some propose full-blown pro- gramming languages, some

Generic Structure of Discussion Sections in ESP Research Articles across International and Iranian Journals

Directory of Open Access Journals (Sweden)

Masoud Khalili Sabet

2015-04-01

Full Text Available Reviewing literature reveals that identifying generic structure of research articles (RAs in different fields of study, especially ESP, has received much attention. The major purpose behind such trends of research has been raising researchers' awareness of the common conventions in writing RAs. Along with this universal trend, a lot of genre studies have been done in Iranian context; however, it seems that ESP RAs have not been paid due attention yet. Hence this study aimed at investigating the generic structure of ESP RAs in international and Iranian journals. Applying Kanoksilapatham's (2007 model to the compiled corpus, it was found that contextualizing the study (Move 1 and consolidating results (Move 2 were the obligatory moves in Discussion section of ESP RAs across international and Iranian journals. Evaluation of the findings was a new step found in international Discussion sections but absent in Iranian ones. Related discussion of these findings prepares the researchers for publishing in international and Iranian ESP journals. Keywords: ESP, Discussion section, Move, Step, Author presence, Generic structure

Dynamic competition in pharmaceuticals. Patent expiry, generic penetration, and industry structure.

Science.gov (United States)

Magazzini, Laura; Pammolli, Fabio; Riccaboni, Massimo

2004-06-01

This paper investigates patterns of industrial dynamics and competition in the pharmaceutical industry, with particular reference to the consequences of patent expiry in different countries. We focus on the competition at the level of single chemical entities, distinguishing between original brands and generic products. Quarterly data, spanning from July 1987 to December 1998, on sales of pharmaceutical products in four countries (USA, UK, Germany, and France) constitute the basis of our analysis. All the products containing major molecules whose patent expiration date lies between 1986 and 1996 are included in our sample. We show how diffusion of generics is linked to the characteristics of the market and investigate how price dynamics of original products are affected by generic competition. Our empirical investigation shows that the dynamics of drug prices and the competition by generic drugs vary significantly across countries. This heterogeneity notwithstanding, a clear distinction seems to emerge. On the one hand, systems that rely on market-based competition in pharmaceuticals promote a clear distinction between firms that act as innovators and firms that act as imitators after patent expiry. Here, original products enjoy premium prices and exclusivity profits under patent protection, and face fierce price competition after patent expiry. On the other hand, in systems that rely on administered prices, penetration by generic drugs tends to be rather limited. Its descriptive and preliminary nature notwithstanding, our analysis seems to have relevant implications at different levels of generality, especially for Europe.

Minimizing technical variation during sample preparation prior to label-free quantitative mass spectrometry.

Science.gov (United States)

Scheerlinck, E; Dhaenens, M; Van Soom, A; Peelman, L; De Sutter, P; Van Steendam, K; Deforce, D

2015-12-01

Sample preparation is the crucial starting point to obtain high-quality mass spectrometry data and can be divided into two main steps in a bottom-up proteomics approach: cell/tissue lysis with or without detergents and a(n) (in-solution) digest comprising denaturation, reduction, alkylation, and digesting of the proteins. Here, some important considerations, among others, are that the reagents used for sample preparation can inhibit the digestion enzyme (e.g., 0.1% sodium dodecyl sulfate [SDS] and 0.5 M guanidine HCl), give rise to ion suppression (e.g., polyethylene glycol [PEG]), be incompatible with liquid chromatography-tandem mass spectrometry (LC-MS/MS) (e.g., SDS), and can induce additional modifications (e.g., urea). Taken together, all of these irreproducible effects are gradually becoming a problem when label-free quantitation of the samples is envisioned such as during the increasingly popular high-definition mass spectrometry (HDMS(E)) and sequential window acquisition of all theoretical fragment ion spectra (SWATH) data-independent acquisition strategies. Here, we describe the detailed validation of a reproducible method with sufficient protein yield for sample preparation without any known LC-MS/MS interfering substances by using 1% sodium deoxycholate (SDC) during both cell lysis and in-solution digest. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

An overview of the main foodstuff sample preparation technologies for tetracycline residue determination.

Science.gov (United States)

Pérez-Rodríguez, Michael; Pellerano, Roberto Gerardo; Pezza, Leonardo; Pezza, Helena Redigolo

2018-05-15

Tetracyclines are widely used for both the treatment and prevention of diseases in animals as well as for the promotion of rapid animal growth and weight gain. This practice may result in trace amounts of these drugs in products of animal origin, such as milk and eggs, posing serious risks to human health. The presence of tetracycline residues in foods can lead to the transmission of antibiotic-resistant pathogenic bacteria through the food chain. In order to ensure food safety and avoid exposure to these substances, national and international regulatory agencies have established tolerance levels for authorized veterinary drugs, including tetracycline antimicrobials. In view of that, numerous sensitive and specific methods have been developed for the quantification of these compounds in different food matrices. One will note, however, that the determination of trace residues in foods such as milk and eggs often requires extensive sample extraction and preparation prior to conducting instrumental analysis. Sample pretreatment is usually the most complicated step in the analytical process and covers both cleaning and pre-concentration. Optimal sample preparation can reduce analysis time and sources of error, enhance sensitivity, apart from enabling unequivocal identification, confirmation and quantification of target analytes. The development and implementation of more environmentally friendly analytical procedures, which involve the use of less hazardous solvents and smaller sample sizes compared to traditional methods, is a rapidly increasing trend in analytical chemistry. This review seeks to provide an updated overview of the main trends in sample preparation for the determination of tetracycline residues in foodstuffs. The applicability of several extraction and clean-up techniques employed in the analysis of foodstuffs, especially milk and egg samples, is also thoroughly discussed. Copyright © 2018 Elsevier B.V. All rights reserved.

Exploring the opinions and experiences of patients with generic substitution: a representative study of Polish society.

Science.gov (United States)

Drozdowska, Aleksandra; Hermanowski, Tomasz

2015-02-01

Generics have the potential to contain drug therapy costs; successful implementation of generic substitution policy largely depends on consumers' willingness to choose generics. This study aims to analyse the opinions, experiences and preferences of Polish patients towards generic medicines. The study was performed in Poland. The survey was conducted in June 2013 by means of face-to-face interviews. Respondents were drawn from the general population according to a population structure. The study covered a representative sample of 1,000 Poles; the results can be generalized to apply to the Polish population at large. Fifty-two percent of respondents declared to be more often choosing generics, twenty-three percent did not have any specific preferences, and twenty-five percent were more willing to choose brand-name medicines. Past experience with cheaper generic medicines, secondary or lower education, low income and residence in specific regions of Poland were all significantly associated with an increased willingness to choose generics. Respondents' attitudes towards generics were mostly influenced by the opinions of doctors and pharmacists. According to respondents, attitudes towards generics among doctors, pharmacists, family and friends, and in the mass media were mostly positive. There was no relationship between the preference of respondents for generics and factors such as their age, life stage, gender, household size or urban/rural locality. As a result of substituting a brand-name drug with its generic equivalent, 72 % of respondents reported that they had not noticed any difference in drug effectiveness; 21 % had experienced a reduced effectiveness of treatment or increased side effects at least once; and 7 % claimed the generic worked better. The majority of respondents who used cheaper substitutes claimed that generics represented good or very good quality. The study demonstrates that, when choosing medicines, Poles rely mainly on the opinions of their

40 CFR 721.9959 - Polyurethane polymer (generic).

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Polyurethane polymer (generic). 721... Substances § 721.9959 Polyurethane polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polyurethane polymer (PMN P-01...

Proceedings Workshop on Generic Programming (WGP2000)

NARCIS (Netherlands)

Jeuring, J.T.

2000-01-01

This report contains the papers selected for presentation at the 2nd Workshop on Generic Programming (WGP2000), which was held on July 6, 2000 in Ponte de Lima, Portugal. Generic programming is about making programs more adaptable by making them more general. Generic programs often embody

Skin rash during treatment with generic itraconazole.

Science.gov (United States)

De Vuono, Antonio; Palleria, Caterina; Scicchitano, Francesca; Squillace, Aida; De Sarro, Giovambattista; Gallelli, Luca

2014-04-01

Generic drugs have the same active substance, the same pharmaceutical form, the same therapeutic indications and a similar bioequivalence with the reference medicinal product (branded). Although a similar efficacy is postulated, some cases of clinical inefficacy during treatment with generic formulations have been reported. In this case, we describe a woman with onychomycosis that developed a skin rash during treatment with a generic formulation of itraconazole. Drug administration and its re-challenge confirmed the association between itraconazole and skin rash. Both Naranjo probability scale and World Health Organization causality assessment scale documented a probable association between generic-itraconazole and skin rash. The switch from generic formulation to brand one induced an improvement of symptoms. Since we are unable to evaluate the role of each excipient in the development of skin rash, we cannot rule out their involvement. However, more data are necessary to better define the similarities or differences between branded and generic formulations.

Is bioavailability altered in generic versus brand anticonvulsants?

Science.gov (United States)

Jankovic, Slobodan M; Ignjatovic Ristic, Dragana

2015-03-01

Therapeutic window of anticonvulsants is not a wide one, with phenytoin being one extreme, which can be classified as a narrow therapeutic index drug, since its ratio between the least toxic and the least effective concentration is less than twofold. In order to obtain marketing authorization, a generic anticonvulsant should demonstrate relative bioequivalence with its brand-name counterpart. However, although bioequivalent, generic anticonvulsants still do not have the same bioavailability as brand-name drugs, which may lead to larger fluctuations of steady-state plasma concentrations, and sometimes to loss of seizure control if a patient is switched from brand-name to generic or from generic to generic anticonvulsant. Generic anticonvulsants are effective, safe and affordable drugs for treatment of epilepsy, and patients could be successfully treated with them from the very beginning. It is switching from brand-name to generic anticonvulsant or from one generic anticonvulsant to another that should be avoided in clinical practice, since subtle differences in bioavailability may disturb optimal degree of seizure control to which the patient was previously successfully titrated.

Challenges of biological sample preparation for SIMS imaging of elements and molecules at subcellular resolution

International Nuclear Information System (INIS)

Chandra, Subhash

2008-01-01

Secondary ion mass spectrometry (SIMS) based imaging techniques capable of subcellular resolution characterization of elements and molecules are becoming valuable tools in many areas of biology and medicine. Due to high vacuum requirements of SIMS, the live cells cannot be analyzed directly in the instrument. The sample preparation, therefore, plays a critical role in preserving the native chemical composition for SIMS analysis. This work focuses on the evaluation of frozen-hydrated and frozen freeze-dried sample preparations for SIMS studies of cultured cells with a CAMECA IMS-3f dynamic SIMS ion microscope instrument capable of producing SIMS images with a spatial resolution of 500 nm. The sandwich freeze-fracture method was used for fracturing the cells. The complimentary fracture planes in the plasma membrane were characterized by field-emission secondary electron microscopy (FESEM) in the frozen-hydrated state. The cells fractured at the dorsal surface were used for SIMS analysis. The frozen-hydrated SIMS analysis of individual cells under dynamic primary ion beam (O 2 + ) revealed local secondary ion signal enhancements correlated with the water image signals of 19 (H 3 O) + . A preferential removal of water from the frozen cell matrix in the Z-axis was also observed. These complications render the frozen-hydrated sample type less desirable for subcellular dynamic SIMS studies. The freeze-drying of frozen-hydrated cells, either inside the instrument or externally in a freeze-drier, allowed SIMS imaging of subcellular chemical composition. Morphological evaluations of fractured freeze-dried cells with SEM and confocal laser scanning microscopy (CLSM) revealed well-preserved mitochondria, Golgi apparatus, and stress fibers. SIMS analysis of fractured freeze-dried cells revealed well-preserved chemical composition of even the most highly diffusible ions like K + and Na + in physiologically relevant concentrations. The high K-low Na signature in individual cells

Challenges of biological sample preparation for SIMS imaging of elements and molecules at subcellular resolution

Science.gov (United States)

Chandra, Subhash

2008-12-01

Secondary ion mass spectrometry (SIMS) based imaging techniques capable of subcellular resolution characterization of elements and molecules are becoming valuable tools in many areas of biology and medicine. Due to high vacuum requirements of SIMS, the live cells cannot be analyzed directly in the instrument. The sample preparation, therefore, plays a critical role in preserving the native chemical composition for SIMS analysis. This work focuses on the evaluation of frozen-hydrated and frozen freeze-dried sample preparations for SIMS studies of cultured cells with a CAMECA IMS-3f dynamic SIMS ion microscope instrument capable of producing SIMS images with a spatial resolution of 500 nm. The sandwich freeze-fracture method was used for fracturing the cells. The complimentary fracture planes in the plasma membrane were characterized by field-emission secondary electron microscopy (FESEM) in the frozen-hydrated state. The cells fractured at the dorsal surface were used for SIMS analysis. The frozen-hydrated SIMS analysis of individual cells under dynamic primary ion beam (O 2+) revealed local secondary ion signal enhancements correlated with the water image signals of 19(H 3O) +. A preferential removal of water from the frozen cell matrix in the Z-axis was also observed. These complications render the frozen-hydrated sample type less desirable for subcellular dynamic SIMS studies. The freeze-drying of frozen-hydrated cells, either inside the instrument or externally in a freeze-drier, allowed SIMS imaging of subcellular chemical composition. Morphological evaluations of fractured freeze-dried cells with SEM and confocal laser scanning microscopy (CLSM) revealed well-preserved mitochondria, Golgi apparatus, and stress fibers. SIMS analysis of fractured freeze-dried cells revealed well-preserved chemical composition of even the most highly diffusible ions like K + and Na + in physiologically relevant concentrations. The high K-low Na signature in individual cells

14C sample preparation for AMS microdosing studies at Lund University using online combustion and septa-sealed vials

Science.gov (United States)

Sydoff, Marie; Stenström, Kristina

2010-04-01

The Department of Physics at Lund University is participating in a European Union project called EUMAPP (European Union Microdose AMS Partnership Programme), in which sample preparation and accelerator mass spectrometry (AMS) measurements of biological samples from microdosing studies have been made. This paper describes a simplified method of converting biological samples to solid graphite for 14C analysis with AMS. The method is based on online combustion of the samples, and reduction of CO 2 in septa-sealed vials. The septa-sealed vials and disposable materials are used to eliminate sample cross-contamination. Measurements of ANU and Ox I standards show deviations of 2% and 3%, respectively, relative to reference values. This level of accuracy is sufficient for biological samples from microdosing studies. Since the method has very few handling steps from sample to graphite, the risk of failure during the sample preparation process is minimized, making the method easy to use in routine preparation of samples.

14C sample preparation for AMS microdosing studies at Lund University using online combustion and septa-sealed vials

International Nuclear Information System (INIS)

Sydoff, Marie; Stenstroem, Kristina

2010-01-01

The Department of Physics at Lund University is participating in a European Union project called EUMAPP (European Union Microdose AMS Partnership Programme), in which sample preparation and accelerator mass spectrometry (AMS) measurements of biological samples from microdosing studies have been made. This paper describes a simplified method of converting biological samples to solid graphite for 14 C analysis with AMS. The method is based on online combustion of the samples, and reduction of CO 2 in septa-sealed vials. The septa-sealed vials and disposable materials are used to eliminate sample cross-contamination. Measurements of ANU and Ox I standards show deviations of 2% and 3%, respectively, relative to reference values. This level of accuracy is sufficient for biological samples from microdosing studies. Since the method has very few handling steps from sample to graphite, the risk of failure during the sample preparation process is minimized, making the method easy to use in routine preparation of samples.

A multicenter experience with generic tacrolimus conversion.

Science.gov (United States)

McDevitt-Potter, Lisa M; Sadaka, Basma; Tichy, Eric M; Rogers, Christin C; Gabardi, Steven

2011-09-27

The first generic tacrolimus product gained Food and Drug Administration approval in August 2009. This prospective, observational trial sought to determine the need for dose titrations and measure drug cost savings on conversion to generic tacrolimus. Transplant recipients on stable tacrolimus doses were converted from brand to generic tacrolimus on a mg:mg basis. Data were collected at the time of generic conversion (study arm) and at a time point exactly 6 months before conversion (control arm) for all subjects. Seventy conversions from four centers are reported. Subjects were a mean of 70 months after kidney (n=37), liver (n=28), or multiorgan (n=5) transplant. In the study arm, mean tacrolimus doses were 4.4 and 4.5 mg/d and mean tacrolimus trough concentrations were 5.8 and 5.9 ng/mL before and after conversion, respectively. In the control arm, mean tacrolimus doses were 4.6 and 4.6 mg/d and mean tacrolimus trough concentrations were 6.1 and 5.9 ng/mL before and after the control time point, respectively. Dose titrations occurred in five patients (7%) in the control arm and 15 patients (21%) in the study arm (P=0.028). Mean monthly drug costs were $645 for brand, $593 for generic, and $595 for generic after dose titrations. Mean monthly patient copays were $38 for brand and $15 for generic. These cumulative data show that dose requirements and trough levels are similar between brand and generic tacrolimus and that generic substitution allows for savings. However, postconversion monitoring is prudent as patients may require dose titration.

The role of sample preparation in interpretation of trace element concentration variability in moss bioindication studies

Science.gov (United States)

Migaszewski, Z.M.; Lamothe, P.J.; Crock, J.G.; Galuszka, A.; Dolegowska, S.

2011-01-01

Trace element concentrations in plant bioindicators are often determined to assess the quality of the environment. Instrumental methods used for trace element determination require digestion of samples. There are different methods of sample preparation for trace element analysis, and the selection of the best method should be fitted for the purpose of a study. Our hypothesis is that the method of sample preparation is important for interpretation of the results. Here we compare the results of 36 element determinations performed by ICP-MS on ashed and on acid-digested (HNO3, H2O2) samples of two moss species (Hylocomium splendens and Pleurozium schreberi) collected in Alaska and in south-central Poland. We found that dry ashing of the moss samples prior to analysis resulted in considerably lower detection limits of all the elements examined. We also show that this sample preparation technique facilitated the determination of interregional and interspecies differences in the chemistry of trace elements. Compared to the Polish mosses, the Alaskan mosses displayed more positive correlations of the major rock-forming elements with ash content, reflecting those elements' geogenic origin. Of the two moss species, P. schreberi from both Alaska and Poland was also highlighted by a larger number of positive element pair correlations. The cluster analysis suggests that the more uniform element distribution pattern of the Polish mosses primarily reflects regional air pollution sources. Our study has shown that the method of sample preparation is an important factor in statistical interpretation of the results of trace element determinations. ?? 2010 Springer-Verlag.

Specific and generic stem biomass and volume models of tree species in a West African tropical semi-deciduous forest

DEFF Research Database (Denmark)

Goussanou, Cédric A.; Guendehou, Sabin; Assogbadjo, Achille E.

2016-01-01

The quantification of the contribution of tropical forests to global carbon stocks and climate change mitigation requires availability of data and tools such as allometric equations. This study made available volume and biomass models for eighteen tree species in a semi-deciduous tropical forest...... in West Africa. Generic models were also developed for the forest ecosystem, and basic wood density determined for the tree species. Non-destructive sampling approach was carried out on five hundred and one sample trees to analyse stem volume and biomass. From the modelling of volume and biomass...... enabled to conclude that the non-destructive sampling was a good approach to determining reliable basic wood density. The comparative analysis of species-specific models in this study with selected generic models for tropical forests indicated low probability to identify effective generic models with good...

Sample preparation for the HAW project and experimental results from the HFR

International Nuclear Information System (INIS)

Garcia Celma, A.; Wees, H. van; Miralles, L.

1990-09-01

This report deals with the preparation and analysis of samples, during the period May 1989-November 1989, for the High-Active Waste (HAW) project, a large-scale in situ test being performed underground in the Asse salt mine, Remlingen FRG. The development of the technical procedures required, and the scientific results, which regard mostly characterization of Potasas del Llobregat sample, are reported. Prior to using the samples in both the H.A.W. and the H.F.R. experiments they have to be machined to fit their holders. Technical improvements for machining samples of salt are reported. (H.W.). 9 refs.; 68 figs.; 10 tabs

Brand loyalty, patients and limited generic medicines uptake.

Science.gov (United States)

Costa-Font, Joan; Rudisill, Caroline; Tan, Stefanie

2014-06-01

The sluggish development of European generic drug markets depends heavily on demand side factors, and more specifically, patients' and doctors' loyalty to branded products. Loyalty to originator drugs, to the point where originator prices rise upon generic entry has been described as the 'generics paradox'. Originator loyalty can emerge for a plethora of reasons; including costs, perceptions about quality and physician advice. We know very little about the behavioural underpinnings of brand loyalty from the consumer or patient standpoint. This paper attempts to test the extent to which patients are brand loyal by drawing upon Spain's 2002 Health Barometer survey as it includes questions about consumer acceptance of generics in a country with exceptionally low generic uptake and substitution at the time of the study. Our findings suggest that at least 13% of the population would not accept generics as substitutes to the originator. These results confirm evidence of brand loyalty for a minority. Alongside high levels of awareness of generics, we find that low cost-sharing levels explain consumer brand loyalty but their impact on acceptance of generic substitution is very small. Higher cost-sharing and exempting fewer patients from cost-sharing have the potential to encourage generic acceptance. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Sample preparation method for ICP-MS measurement of 99Tc in a large amount of environmental samples

International Nuclear Information System (INIS)

Kondo, M.; Seki, R.

2002-01-01

Sample preparation for measurement of 99 Tc in a large amount of soil and water samples by ICP-MS has been developed using 95m Tc as a yield tracer. This method is based on the conventional method for a small amount of soil samples using incineration, acid digestion, extraction chromatography (TEVA resin) and ICP-MS measurement. Preliminary concentration of Tc has been introduced by co-precipitation with ferric oxide. The matrix materials in a large amount of samples were more sufficiently removed with keeping the high recovery of Tc than previous method. The recovery of Tc was 70-80% for 100 g soil samples and 60-70% for 500 g of soil and 500 L of water samples. The detection limit of this method was evaluated as 0.054 mBq/kg in 500 g soil and 0.032 μBq/L in 500 L water. The determined value of 99 Tc in the IAEA-375 (soil sample collected near the Chernobyl Nuclear Reactor) was 0.25 ± 0.02 Bq/kg. (author)

Influencers of generic drug utilization: A systematic review.

Science.gov (United States)

Howard, Jennifer N; Harris, Ilene; Frank, Gavriella; Kiptanui, Zippora; Qian, Jingjing; Hansen, Richard

2017-08-04

With an increase in prescription drug spending and rising drug costs there is a need to encourage the use of generic prescription drugs. However, maximizing generic drug use is not possible without the public's positive perception and meeting their informational needs about generic drugs. Thus, improving the public's confidence in, and knowledge of generic drugs on the market is critical. The objective of this systematic review is to examine and evaluate the studies focusing on the nature and extent of key factors influencing generic drug use in the United States in order to help guide policy, education and practice interventions. Using multiple search engines and key word screening criteria, empirical studies published in English between January 1, 2005 and December 31, 2015 were identified. A qualitative synthesis of the evidence identified domains of key factors that influenced generic drug use across studies. Over 3000 citations met the key word screening criteria; 67 of these met inclusion criteria for the systematic review. Seven domains of factors that influence generic drug utilization were identified: 1) patient-related factors, 2) formulary management or cost containment, 3) healthcare policies, 4) promotional activities, 5) educational initiatives, 6) technology, and 7) physician-related factors. Patients, physicians, pharmacists, formulary managers, and policymakers play an important role in generic drug use. Understanding the factors influencing generic drug use can help guide future policy, education, and practice interventions to increase generic drug use. Copyright © 2017 Elsevier Inc. All rights reserved.

A critical review of microextraction by packed sorbent as a sample preparation approach in drug bioanalysis.

Science.gov (United States)

Alves, Gilberto; Rodrigues, Márcio; Fortuna, Ana; Falcão, Amílcar; Queiroz, João

2013-06-01

Sample preparation is widely accepted as the most labor-intensive and error-prone part of the bioanalytical process. The recent advances in this field have been focused on the miniaturization and integration of sample preparation online with analytical instrumentation, in order to reduce laboratory workload and increase analytical performance. From this perspective, microextraction by packed sorbent (MEPS) has emerged in the last few years as a powerful sample preparation approach suitable to be easily automated with liquid and gas chromatographic systems applied in a variety of bioanalytical areas (pharmaceutical, clinical, toxicological, environmental and food research). This paper aims to provide an overview and a critical discussion of recent bioanalytical methods reported in literature based on MEPS, with special emphasis on those developed for the quantification of therapeutic drugs and/or metabolites in biological samples. The advantages and some limitations of MEPS, as well as its comparison with other extraction techniques, are also addressed herein.

Quality Assessment of Platelet-Rich Fibrin-Like Matrix Prepared from Whole Blood Samples after Extended Storage

Directory of Open Access Journals (Sweden)

Hideo Kawabata

2017-09-01

Full Text Available The platelet-rich fibrin–like matrix (PRFM is usually prepared onsite and immediately used for regenerative therapy. Nonetheless, to meet the clinical necessity of preserving the PRFM without quality deterioration, we developed a method for preparation of PRFMs from short-term-stored whole blood (WB samples. In this study, to evaluate the practical expiration date of storage, we extended the storage time of WB samples from 2 to 7 days and assessed the quality of the resulting PRFMs. WB samples collected with acid-citrate-dextrose were stored with gentle agitation at ambient temperature. To prepare PRFMs, the stored WB samples were mixed with CaCl2 in glass tubes and centrifuged. Fibrin fiber networks, CD41 and CD62P expression, and Platelet Derived Growth Factor-BB (PDGF-BB levels were examined by scanning electron microscopy (SEM, flow cytometry, and an Enzyme-Linked ImmunoSorbent Assay (ELISA, respectively. Long-term storage had no significant effect on either blood cell counts or platelet functions tested. The resulting PRFMs were visually identical to freshly prepared ones. PDGF-BB levels did not markedly decrease in a time-dependent manner. However, fibrin fibers gradually became thinner after storage. Although the coagulation activity may diminish, we propose that PRFMs can be prepared—without evident loss of quality—from WB samples stored for up to 7 days by our previously developed method.

Development of a Novel Self-Enclosed Sample Preparation Device for DNA/RNA Isolation in Space

Science.gov (United States)

Zhang, Ye; Mehta, Satish K.; Pensinger, Stuart J.; Pickering, Karen D.

2011-01-01

Modern biology techniques present potentials for a wide range of molecular, cellular, and biochemistry applications in space, including detection of infectious pathogens and environmental contaminations, monitoring of drug-resistant microbial and dangerous mutations, identification of new phenotypes of microbial and new life species. However, one of the major technological blockades in enabling these technologies in space is a lack of devices for sample preparation in the space environment. To overcome such an obstacle, we constructed a prototype of a DNA/RNA isolation device based on our novel designs documented in the NASA New Technology Reporting System (MSC-24811-1/3-1). This device is self-enclosed and pipette free, purposely designed for use in the absence of gravity. Our design can also be modified easily for preparing samples in space for other applications, such as flowcytometry, immunostaining, cell separation, sample purification and separation according to its size and charges, sample chemical labeling, and sample purification. The prototype of our DNA/RNA isolation device was tested for efficiencies of DNA and RNA isolation from various cell types for PCR analysis. The purity and integrity of purified DNA and RNA were determined as well. Results showed that our developed DNA/RNA isolation device offers similar efficiency and quality in comparison to the samples prepared using the standard protocol in the laboratory.

Generic domain models in software engineering

Science.gov (United States)

Maiden, Neil

1992-01-01

This paper outlines three research directions related to domain-specific software development: (1) reuse of generic models for domain-specific software development; (2) empirical evidence to determine these generic models, namely elicitation of mental knowledge schema possessed by expert software developers; and (3) exploitation of generic domain models to assist modelling of specific applications. It focuses on knowledge acquisition for domain-specific software development, with emphasis on tool support for the most important phases of software development.

Soil and Water – What is Detectable through Microbiological Sample Preparation Techniques

Science.gov (United States)

The concerns of a potential terrorist’s use of biological agents in soil and ground water are articulated by comparisons to major illnesses in this Country involving contaminated drinking water sources. Objectives are focused on the importance of sample preparation in the rapid, ...

Fluoroquinolone antibiotics in environmental waters: sample preparation and determination.

Science.gov (United States)

Speltini, Andrea; Sturini, Michela; Maraschi, Federica; Profumo, Antonella

2010-04-01

The aim of this review is to provide a general overview on the analytical methods proposed in the last decade for trace fluoroquinolone (FQ) determination in environmental waters. A large number of studies have been developed on this topic in reason of the importance of their monitoring in the studies of environmental mobility and potential degradation pathways. Every step of the analysis has been carefully considered, with a particular attention to sample preparation, in relationship with the problems involved in the analysis of real matrices. The different strategies to minimise interference from organic matter and to achieve optimal sensitivity, especially important in those samples with lower FQ concentrations, were also highlighted. Results and progress in this field have been described and critically commented. Moreover, a worldwide overview on the presence of FQs in the environmental waters has been reported.

[General awareness and use of generic medication among citizens of Tubarão, state of Santa Catarina, Brazil].

Science.gov (United States)

Blatt, Carine Raquel; Trauthman, Silvana Cristina; Schmidt, Edegar Henrique; Marchesan, Samuel; da Silva, Luana May; Martins, João Luiz

2012-01-01

Although generic medication has been introduced in the country to offer an accessible alternative to brand-name medication, it represents only 14% of sales in number of units within the pharmaceutical market. The aim of this work was to research the level of awareness and the use of generic products among residents of the municipality of Tubarão, State of Santa Catarina, Brazil. A transversal study was carried out with a sample of 234 interviewees, distributed among municipal areas. With regard to use, the majority of those interviewed had used generic medication, and half of them had at least one such product in their home. To verify awareness of different types of medication, pictures with the generic, brand name and similar packaging for paracetamol and atenolol were shown and 91% were able to identify all products correctly. To be of higher economic standing, already having used generic products, believing that the generic medication has the same effect as the brand name medication, finding generic products in drugstores easily and being accustomed to buy generic products, were factors that were positively associated with the correct identification.

A comparison of generic drug prices in seven European countries: a methodological analysis.

Science.gov (United States)

Wouters, Olivier J; Kanavos, Panos G

2017-03-31

Policymakers and researchers frequently compare the prices of medicines between countries. Such comparisons often serve as barometers of how pricing and reimbursement policies are performing. The aim of this study was to examine methodological challenges to comparing generic drug prices. We calculated all commonly used price indices based on 2013 IMS Health data on sales of 3156 generic drugs in seven European countries. There were large differences in generic drug prices between countries. However, the results varied depending on the choice of index, base country, unit of volume, method of currency conversion, and therapeutic category. The results also differed depending on whether one looked at the prices charged by manufacturers or those charged by pharmacists. Price indices are a useful statistical approach for comparing drug prices across countries, but researchers and policymakers should interpret price indices with caution given their limitations. Price-index results are highly sensitive to the choice of method and sample. More research is needed to determine the drivers of price differences between countries. The data suggest that some governments should aim to reduce distribution costs for generic drugs.

Generic licensing issues applicable to Wolsong 3 and 4 licensing review

International Nuclear Information System (INIS)

Boyd, Frederick C.

1994-01-01

The Wolsong 3 and 4 nuclear power plants are of CANDU type which were designed according to the rules and regulations of the Atomic Energy Control Board (AECB) of Canada. In 1992 AECB staff issued a first formal report (to the AECB Board) on 'generic safety issues affecting power reactors'. This was followed by a second report in 1993. These reports dealt with safety issues associated with Canadian CANDU nuclear power plants that applied to all or several plants and were considered insufficiently resolved. In most cases the concern was lack of certainty in the related safety analyses. The AECB staff report of 1993 identified eight 'generic action items' and six 'long-term research issues', three of which AECB staff have indicated may be moved into the 'action' category. This report, prepared for the Korea Institute of Nuclear Safety (KINS), reviews the background of the AECB 'generic action items' and the three 'long-term research issues' noted above. It also reviews an additional topic - steam line failure outside of containment - which was included in the request from KINS. In all, twelve issues are covered. These background reviews are followed by a discussion of the relevance of each issue to the licensing review (for Construction Permit) of Wolsong 3 and 4 and recommended actions to be taken by KINS

76 FR 28100 - Activities: Proposed Collection; Comment Request; Generic Clearance for the Collection of...

Science.gov (United States)

2011-05-13

... target population to which generalizations will be made, the sampling frame, the sample design (including... for submission for other generic mechanisms that are designed to yield quantitative results. As a... statistical surveys that yield quantitative results that can be generalized to the population of study. This...

Solvent-assisted dispersive solid-phase extraction: A sample preparation method for trace detection of diazinon in urine and environmental water samples.

Science.gov (United States)

Aladaghlo, Zolfaghar; Fakhari, Alireza; Behbahani, Mohammad

2016-09-02

In this research, a sample preparation method termed solvent-assisted dispersive solid-phase extraction (SA-DSPE) was applied. The used sample preparation method was based on the dispersion of the sorbent into the aqueous sample to maximize the interaction surface. In this approach, the dispersion of the sorbent at a very low milligram level was received by inserting a solution of the sorbent and disperser solvent into the aqueous sample. The cloudy solution created from the dispersion of the sorbent in the bulk aqueous sample. After pre-concentration of the diazinon, the cloudy solution was centrifuged and diazinon in the sediment phase dissolved in ethanol and determined by gas chromatography-flame ionization detector. Under the optimized conditions (pH of solution=7.0, Sorbent: benzophenone, 2%, Disperser solvent: ethanol, 500μL, Centrifuge: centrifuged at 4000rpm for 3min), the method detection limit for diazinon was 0.2, 0.3, 0.3 and 0.3μgL(-1) for distilled water, lake water, waste water and urine sample, respectively. Furthermore, the pre-concentration factor was 363.8, 356.1, 360.7 and 353.38 in distilled water, waste water, lake water and urine sample, respectively. SA-DSPE was successfully used for trace monitoring of diazinon in urine, lake and waste water samples. Copyright © 2016 Elsevier B.V. All rights reserved.