WorldWideScience

Sample records for generation system atmospheric

  1. POCIS: a system to generate pseudo top-of-atmosphere ocean color image for sensor and system evaluation

    Science.gov (United States)

    Lee, ZhongPing; Arnone, Robert; Vaughan, Ronnie

    2010-10-01

    It requires frequent and high-resolution measurements of biogeochemical properties of the oceans in order to obtain the status of the ecosystems and evaluate its role in modulating the climate. Because of the limited coverage and high cost, such a task could not be achieved via traditional ship surveys. Satellite sensors, because of its high revisit time and synoptic coverage, can provide key measurements to remedy the weakness of ship surveys. To ensure reliable and consistent measurements from an ocean color satellite, it not only requires the sensor be well designed and calibrated, also requires the processing software be robust for a wide range of ecosystems. All these require adequate data in order to evaluate and characterize the whole system. Such data, however, will not be available until the sensor is functioning properly in the sky. To overcome this dilemma, we developed POCIS (Pseudo Ocean Color Image Simulator), which can generate top-of-atmosphere ocean color images based on sensor specs. Such images, which can be both regional and global, can then be fed into current/future processing system to generate proxy products, thus not only help to ensure the readiness of the processing system, but also help to identify weakness and strengths of such a system before its launch, and setup the bases for eventual improvements. Details of POCIS, along with examples of proxy VIIRS image products, are presented to demonstrate its capabilities and potentials.

  2. An atmospheric turbulence generator for dynamic tests with LINC-NIRVANA's adaptive optics system

    Science.gov (United States)

    Meschke, D.; Bizenberger, P.; Gaessler, W.; Zhang, X.; Mohr, L.; Baumeister, H.; Diolaiti, E.

    2010-07-01

    LINC-NIRVANA[1] (LN) is an instrument for the Large Binocular Telescope[2] (LBT). Its purpose is to combine the light coming from the two primary mirrors in a Fizeau-type interferometer. In order to compensate turbulence-induced dynamic aberrations, the layer oriented adaptive optics system of LN[3] consists of two major subsystems for each side: the Ground-Layer-Wavefront sensor (GLWS) and the Mid- and High-Layer Wavefront sensor (MHLWS). The MHLWS is currently set up in a laboratory at the Max-Planck-Institute for Astronomy in Heidelberg. To test the multi-conjugate AO with multiple simulated stars in the laboratory and to develop the necessary control software, a dedicated light source is needed. For this reason, we designed an optical system, operating in visible as well as in infrared light, which imitates the telescope's optical train (f-ratio, pupil position and size, field curvature). By inserting rotating surface etched glass phase screens, artificial aberrations corresponding to the atmospheric turbulence are introduced. In addition, different turbulence altitudes can be simulated depending on the position of these screens along the optical axis. In this way, it is possible to comprehensively test the complete system, including electronics and software, in the laboratory before integration into the final LINC-NIRVANA setup. Combined with an atmospheric piston simulator, also this effect can be taken into account. Since we are building two identical sets, it is possible to feed the complete instrument with light for the interferometric combination during the assembly phase in the integration laboratory.

  3. An overview of the use of Open Source in the NASA Langley Atmospheric Science Data Center Archive Next Generation system

    Science.gov (United States)

    Dye, R. A.; Perez, J.; Piatko, P. J.; Coogan, S. P.; Parker, L.

    2012-12-01

    The Atmospheric Science Data Center (ASDC) at NASA Langley Research Center is responsible for the archive and distribution of Earth science data in the areas of radiation budget, clouds, aerosols, and tropospheric chemistry. Over the past several years the ASDC has developed and implemented the Archive Next Generation (ANGe) system, a state-of-the-art data ingest, archival, and distribution system to serve the atmospheric sciences data provider and user communities. ANGe employs Open Source technologies including the JBoss Application Server, a PostGIS-enabled PostgreSQL database system to store geospatial metadata, modules from the GeoTools Open Source Java GIS Toolkit including the Java Topology Suite (JTS) and GeoAPI libraries, and other libraries such as the Spring framework. ANGe was developed using a suite of several Open Source tools comprised of Eclipse, Ant, Subversion and Jenkins. ANGe is also deployed into an operational environment that leverages Open Source technologies from the Linux Operating system to tools such as Ganglia for monitoring. This presentation provides an overview of ANGe with a focus on the Open Source technologies employed in the implementation and deployment of the system. The ASDC is part of Langley's Science Directorate. The Data Center was established in 1991 to support NASA's Earth Observing System and the U.S. Global Change Research Program. It is unique among NASA data centers in the size of its archive, cutting edge computing technology, and full range of data services. For more information regarding ASDC data holdings, documentation, tools and services, visit http://eosweb.larc.nasa.gov.

  4. How coastal surges may be generated by mesoscale atmospheric disturbances that in turn are related to propagating convective systems

    Science.gov (United States)

    Orlic, M.; Belusic, D.; Janekovic, I.; Pasaric, M.

    2010-09-01

    On the morning of 21 June 1978, exceptional sea-level oscillations with a trough-to-crest height of 6 m and a period of 10-20 min were observed in Vela Luka Bay. Slightly less pronounced variability was observed in a wider Middle and South Adriatic east coastal area and, with some delay, along the west coast. In the presentation, one of the original hypotheses put forward to interpret the event, relating it to a mesoscale air-pressure disturbance, is reconsidered by using all the available data as well as state-of-the-art meteorological and oceanographic models. A fresh look at the meteorological data confirms that the atmospheric disturbance propagated at about 22 m/s in a northeastward direction. Additionally, the data suggest that it had the shape of the boxcar function characterized by an air-pressure offset of 3 mbar and duration of 10 min. The meteorological model employed (WRF-ARW) proves unable to reproduce the mesoscale disturbance coinciding with the surge, but it shows that the background atmospheric conditions were favorable for the development of convective systems and therefore also for the formation of mesoscale disturbances. The oceanographic model ADCIRC-2DDI, forced by the described air-pressure disturbance, successfully reproduces sea-level variability in Vela Luka Bay reaching a few meters and thus surpassing the inverted barometer response by two orders of magnitude. The enhancement appears to be due to a four-phase process. The model also suggests that the scattering due to the variable bathymetry and the reflection from the east Adriatic coast resulted in waves that returned towards the west coast and generated considerable sea-level activity there. Similar surges that were observed in the Adriatic more recently (Stari Grad and Mali Ston, 2003; Ist, 2007; Mali Losinj, 2008; Stari Grad, 2010) are also mentioned and the dynamics revealed is used as the basis for a brief discussion of terminology appropriate for such processes.

  5. Improved methodology for generating controlled test atmospheres.

    Science.gov (United States)

    Miller, R R; Letts, R L; Potts, W J; McKenna, M J

    1980-11-01

    Improved methodology has been developed for generating controlled test atmospheres. Vaporization of volatile liquids is accomplished in a 28 mm (O.D.) glass J-tube in conjunction with a compressed air flameless heat torch, a pressure-sensitive switch, and a positive displacement piston pump. The vaporization system has been very reliable with a variety of test materials in studies ranging from a few days to several months. The J-tube vaporization assembly minimizes the possibility of thermal decomposition of the test material and affords a better margin of safety when vaporizing potentially explosive materials.

  6. Lessons from our Own Solar System: Generation Mechanisms of Radio Emissions from Earth, Saturn and Jupiter and Atmospheric Loss from Magnetized versus non-magnetized planets

    Science.gov (United States)

    Brandt, Pontus

    2017-05-01

    The understanding of the engines and mechanisms behind kilometric and decametric radio emissions from the planets in our own solar system have taken great leaps with missions such as the NASA/Cassini, IMAGE and Galileo missions. The periodic Saturn Kilometric Radiation (SKR), the Auroral Kilometric Radiation (AKR) at Earth and the periodic decametric radio emissions from Jupiter all point to the same generation mechanisms: very large-scale explosive plasma heating events in the magnetotail of each of the planets. The character and periodicity of the associated radio emissions not only tells us about the presence of a magnetic field but also about the plasma content and size of the planetary magnetosphere, and the nature of the interaction with the solar wind.The presence of a planetary magnetic field, as could be established for exoplanets by the positive detection of low-frequency exoplanetary radio emissions, has been thought to shield a planet from atmospheric loss to space. However, recent data from Mars Express, MAVEN, and Venus Express, together with the wealth of terrestrial measurements of atmospheric escape to space has brought a surprising question in to light: Does a planetary magnetic field suppress or enhance atmospheric loss? While at the non-magnetized planets such as Mars and Venus, the solar wind has a more direct access to the ionized upper atmosphere, these planets do set up self shielding currents that do limit escape. Furthermore, it is not clear if Mars have lost the majority of its atmosphere by condensation in to surface and sub-surface frost, or through atmospheric escape. At Earth, the geomagnetic field sets up a relatively large cross section to the solar wind, that allows the induced solar-wind electric field to transfer substantial energy to the upper ionosphere and atmosphere resulting in substantial loss. It is therefore not clear how a planetary magnetic field correlates to the atmospheric loss, or if it does at all.In this

  7. Development of Miniaturized Difference Frequency Generation, Fiber Optic, and Quantum Cascade Laser Systems in Conjunction With Integrated Electronics for Global Studies of Atmospheric Tracers Using UAVs.

    Science.gov (United States)

    Witinski, M. F.; Lapson, L. B.; Anderson, J. G.

    2007-12-01

    In order to harness the power of UAVs (Unmanned Aerial Vehicles) for in situ atmospheric monitoring of tracers such as CO2, N2O, CH4, and H2O, we have developed small, lightweight, single mode laser systems with co- developed integrated electronics. The laser sources are of various types including newly developed cavity- enhanced difference frequency generation (CE DFG), distributed feedback quantum cascade lasers (DFB QCLs), and new types of commercially available DFB diode lasers. All are continuous wave (cw) and thermo-electrically cooled, ensuring a high instrument duty cycle in a compact, low maintenance package. The light sources are collimated with miniature aspherical lenses and coupled into a home-built astigmatic Herriott cell for detection of the various targets using direct absorption. In parallel with the optical components, we have developed integrated electrical systems for laser control, data processing, and acquisition. A prototype instrument suite is described that illustrates the importance of parallel development of optical and electrical components in achieving an apparatus that is compact, fully automated, and highly capable scientifically. Although the emphasis here is on atmospheric tracers, this technology could be applied to spectroscopic measurements of other atmospheric species such as isotopes, free radicals, and reactive intermediates.

  8. Three-Dimensional X-ray Observation of Atmospheric Biological Samples by Linear-Array Scanning-Electron Generation X-ray Microscope System

    Science.gov (United States)

    Ogura, Toshihiko

    2011-01-01

    Recently, we developed a soft X-ray microscope called the scanning-electron generation X-ray microscope (SGXM), which consists of a simple X-ray detection system that detects X-rays emitted from the interaction between a scanning electron beam (EB) and the thin film of the sample mount. We present herein a three-dimensional (3D) X-ray detection system that is based on the SGXM technology and designed for studying atmospheric biological samples. This 3D X-ray detection system contains a linear X-ray photodiode (PD) array. The specimens are placed under a CuZn-coated Si3N4 thin film, which is attached to an atmospheric sample holder. Multiple tilt X-ray images of the samples are detected simultaneously by the linear array of X-ray PDs, and the 3D structure is calculated by a new 3D reconstruction method that uses a simulated-annealing algorithm. The resulting 3D models clearly reveal the inner structure of the bacterium. In addition, the proposed method can easily be used for diverse samples in a broad range of scientific fields. PMID:21731770

  9. Three-dimensional X-ray observation of atmospheric biological samples by linear-array scanning-electron generation X-ray microscope system.

    Science.gov (United States)

    Ogura, Toshihiko

    2011-01-01

    Recently, we developed a soft X-ray microscope called the scanning-electron generation X-ray microscope (SGXM), which consists of a simple X-ray detection system that detects X-rays emitted from the interaction between a scanning electron beam (EB) and the thin film of the sample mount. We present herein a three-dimensional (3D) X-ray detection system that is based on the SGXM technology and designed for studying atmospheric biological samples. This 3D X-ray detection system contains a linear X-ray photodiode (PD) array. The specimens are placed under a CuZn-coated Si₃N₄ thin film, which is attached to an atmospheric sample holder. Multiple tilt X-ray images of the samples are detected simultaneously by the linear array of X-ray PDs, and the 3D structure is calculated by a new 3D reconstruction method that uses a simulated-annealing algorithm. The resulting 3D models clearly reveal the inner structure of the bacterium. In addition, the proposed method can easily be used for diverse samples in a broad range of scientific fields.

  10. Three-dimensional X-ray observation of atmospheric biological samples by linear-array scanning-electron generation X-ray microscope system.

    Directory of Open Access Journals (Sweden)

    Toshihiko Ogura

    Full Text Available Recently, we developed a soft X-ray microscope called the scanning-electron generation X-ray microscope (SGXM, which consists of a simple X-ray detection system that detects X-rays emitted from the interaction between a scanning electron beam (EB and the thin film of the sample mount. We present herein a three-dimensional (3D X-ray detection system that is based on the SGXM technology and designed for studying atmospheric biological samples. This 3D X-ray detection system contains a linear X-ray photodiode (PD array. The specimens are placed under a CuZn-coated Si₃N₄ thin film, which is attached to an atmospheric sample holder. Multiple tilt X-ray images of the samples are detected simultaneously by the linear array of X-ray PDs, and the 3D structure is calculated by a new 3D reconstruction method that uses a simulated-annealing algorithm. The resulting 3D models clearly reveal the inner structure of the bacterium. In addition, the proposed method can easily be used for diverse samples in a broad range of scientific fields.

  11. Abnormal storm waves in the winter East/Japan Sea: generation process and hindcasting using an atmosphere-wind wave modelling system

    Directory of Open Access Journals (Sweden)

    H. S. Lee

    2010-04-01

    Full Text Available Abnormal storm waves cause coastal disasters along the coasts of Korean Peninsula and Japan in the East/Japan Sea (EJS in winter, arising due to developed low pressures during the East Asia winter monsoon. The generation of these abnormal storm waves during rough sea states were studied and hindcast using an atmosphere-wave coupled modelling system. Wind waves and swell due to developed low pressures were found to be the main components of abnormal storm waves. The meteorological conditions that generate these waves are classified into three patterns based on past literature that describes historical events as well as on numerical modelling. In hindcasting the abnormal storm waves, a bogussing scheme originally designed to simulate a tropical storm in a mesoscale meteorological model was introduced into the modelling system to enhance the resolution of developed low pressures. The modelling results with a bogussing scheme showed improvements in terms of resolved low pressure, surface wind field, and wave characteristics obtained with the wind field as an input.

  12. Atmospheric Optical Communication Systems.

    Science.gov (United States)

    1981-02-01

    Tnteral system noise due to dark current id is Oven by . 1d = 2qGrB"" (2-9) Dark current is due to detecor biasing in some instances, and in somue...8217 without extansive pro- gr-=:ing exer’ence. Although. the znodel is designed to be Lteracdve, slight mod-.- i~cadons winl ezw :&31 r~ing of the progrsm

  13. Airborne Atmospheric Aerosol Measurement System

    Science.gov (United States)

    Ahn, K.; Park, Y.; Eun, H.; Lee, H.

    2015-12-01

    It is important to understand the atmospheric aerosols compositions and size distributions since they greatly affect the environment and human health. Particles in the convection layer have been a great concern in global climate changes. To understand these characteristics satellite, aircraft, and radio sonde measurement methods have usually been used. An aircraft aerosol sampling using a filter and/or impactor was the method commonly used (Jay, 2003). However, the flight speed particle sampling had some technical limitations (Hermann, 2001). Moreover, the flight legal limit, altitude, prohibited airspace, flight time, and cost was another demerit. To overcome some of these restrictions, Tethered Balloon Package System (T.B.P.S.) and Recoverable Sonde System(R.S.S.) were developed with a very light optical particle counter (OPC), impactor, and condensation particle counter (CPC). Not only does it collect and measure atmospheric aerosols depending on altitudes, but it also monitors the atmospheric conditions, temperature, humidity, wind velocity, pressure, GPS data, during the measurement (Eun, 2013). In this research, atmospheric aerosol measurement using T.B.P.S. in Ansan area is performed and the measurement results will be presented. The system can also be mounted to an unmanned aerial vehicle (UAV) and create an aerial particle concentration map. Finally, we will present measurement data using Tethered Balloon Package System (T.B.P.S.) and R.S.S (Recoverable Sonde System).

  14. Distributed generation systems model

    Energy Technology Data Exchange (ETDEWEB)

    Barklund, C.R.

    1994-12-31

    A slide presentation is given on a distributed generation systems model developed at the Idaho National Engineering Laboratory, and its application to a situation within the Idaho Power Company`s service territory. The objectives of the work were to develop a screening model for distributed generation alternatives, to develop a better understanding of distributed generation as a utility resource, and to further INEL`s understanding of utility concerns in implementing technological change.

  15. Low-frequency sea waves generated by atmospheric convection cells

    Science.gov (United States)

    de Jong, M. P. C.; Battjes, J. A.

    2004-01-01

    The atmospheric origin of low-frequency sea waves that cause seiches in the Port of Rotterdam is investigated using hydrological and meteorological observations. These observations, combined with weather charts, show that all significant seiche events coincide with the passage of a low-pressure area and a cold front. Following these front passages, increased wind speed fluctuations occur with periods on the order of 1 hour. The records show that enhanced low-frequency wave energy at sea and the seiche events in the harbor occur more or less simultaneously with these strong wind speed fluctuations. These oscillatory wind speed changes are due to convection cells that arise in an unstable lower atmosphere in the area behind a cold front, where cold air moves over the relatively warm sea surface. It is shown that the moving system of a cold front and trailing convection cells generates forced low-frequency waves at sea that can cause seiche events inside the harbor. The occurrence of such events may be predictable operationally on the basis of a criterion for the difference in temperature between the air in the upper atmosphere and the water at the sea surface.

  16. An artificially generated atmosphere near a lunar base

    Science.gov (United States)

    Burns, Jack O.; Fernini, Ilias; Sulkanen, Martin; Duric, Nebojsa; Taylor, G. Jeffrey; Johnson, Stewart W.

    1992-09-01

    We discuss the formation of an artificial atmosphere generated by vigorous lunar base activity in this paper. We developed an analytical, steady-state model for a lunar atmosphere based upon previous investigations of the Moon's atmosphere from Apollo. Constant gas-injection rates, ballistic trajectories, and a Maxwellian particle distribution for an oxygen-like gas are assumed. Even for the extreme case of continuous He-3 mining of the lunar regolith, we find that the lunar atmosphere would not significantly degrade astronomical observations beyond about 10 km from the mining operation.

  17. Atmosphere Environment Simulation Scenario Generator for Distributed Simulation System%大气环境仿真剧情生成系统

    Institute of Scientific and Technical Information of China (English)

    张鹏; 龚光红

    2008-01-01

    The Atmosphere Environment Simulation Scenario Generator (AESSG) is designed to help users to extract simulation scenario. It is convenient and fast for user to construct the simulation federation based on HLA. It is allowed to use human language describing the searching condition. AESSG provides the service for users to editing the searching result within reasonable scopes. User interface can provide the environment for users to search and edit environment data. Users can submit the searching condition that specified in human language or in numeric terms. Fuzzy logical technique is introduced to deal with the transition from human language to machine code. The resource database is constructed, which can store multi-resolution atmosphere data and models.%大气环境仿真剧情生成系统(AESSG)辅助用户利用不同来源的大气环境数据生成能够满足仿真需求的大气环境仿真剧情.支持输入人类语言描述的模糊查询条件.模糊检索后查询结果按照符合度来排列,供用户选择.模糊逻辑技术引入到环境信息搜索引擎来实现模糊搜索.AESSG运行时系统作为联邦成员参与仿真联邦的仿真,实时响应联邦内的环境信息请求.大气环境信息资源库支持多来源、多分辨率的大气环境数据与模型的存储.

  18. Sub-atmospheric disk generators for coal-fired MHD/steam combined cycle power plant

    Energy Technology Data Exchange (ETDEWEB)

    Messerle, H.K.; Fang, Y.; Simpson, S.W.; Marty, S.M. (Sydney Univ. (Australia). School of Electrical Engineering)

    1989-01-01

    A coal fired MHD disk generator in a combined cycle MHD/steam power generation system with a diffuser operating at sub-atmospheric pressure is proposed. The effects of pressure on the performance of a radial outflow MHD disk generator and other system components are analysed. Using a previous study as a reference case, preliminary calculations show that, in such a sub-atmospheric system, improved power station efficiency can be achieved. In addition, operation at reduced values of magnetic field strength would be feasible. Calculations have also been carried out for a 30 MW{sub th} experimental disk generator operating at reduced pressure with a magnetic field strength of 2 T. Flow conditions at sub-atmospheric pressure would provide an improved simulation of a full-scale generator operating at normal pressures. (author).

  19. Small Next-Generation Atmospheric Probe (SNAP) Concept

    Science.gov (United States)

    Sayanagi, K. M.; Dillman, R. A.; Simon, A. A.; Atkinson, D. H.; Wong, M. H.; Spilker, T. R.; Saikia, S.; Li, J.; Hope, D.

    2017-01-01

    We present the Small Next-Generation Atmospheric Probe (SNAP) as a secondary payload concept for future missions to giant planets. As a case study, we examine the advantages, cost and risk of adding SNAP to the future Uranus Orbiter and Probe flag-ship mission; in combination with the missions main probe, SNAP would perform atmospheric in-situ measurements at a second location.

  20. Generation of nano roughness on fibrous materials by atmospheric plasma

    Science.gov (United States)

    Kulyk, I.; Scapinello, M.; Stefan, M.

    2012-12-01

    Atmospheric plasma technology finds novel applications in textile industry. It eliminates the usage of water and of hazard liquid chemicals, making production much more eco-friendly and economically convenient. Due to chemical effects of atmospheric plasma, it permits to optimize dyeing and laminating affinity of fabrics, as well as anti-microbial treatments. Other important applications such as increase of mechanical resistance of fiber sleeves and of yarns, anti-pilling properties of fabrics and anti-shrinking property of wool fabrics were studied in this work. These results could be attributed to the generation of nano roughness on fibers surface by atmospheric plasma. Nano roughness generation is extensively studied at different conditions. Alternative explanations for the important practical results on textile materials and discussed.

  1. Next Generation HVAC System

    Science.gov (United States)

    Takagi, Yasuo; Murakami, Yoshiki; Hanada, Yuuichi; Nishimura, Nobutaka; Yamazaki, Kenichi; Itoh, Yasuyuki

    A new HVAC (Heating, Ventilating, and Air-Conditioning) system for buildings is proposed. The key technology for the system is a twin coil air handling unit (AHU) and its advanced control method. One coil is equipped to cool and dehumidify the fresh air intake, and the other coil is for cooling circulated air. The deeply chilled water is necessary only for removing the moisture from the fresh air. The latter coil requires moderately cool water according to the HVAC load. Then 2 kinds of chilled water in terms of temperature should be prepared. The structure helps saving the energy consumption for air-conditioning because the higher chilled water temperature implies the better chiller efficiency (COP: Coefficient of Performance). In addition, an advanced control method that is called an ‘Air-Water cooperation system’ is introduced. The control system mainly focuses on energy savings through changing the temperature of the chilled water and supply air according to the HVAC load and weather conditions. In this paper, we introduce a Next Generation HVAC system with its control system and present evaluation results of the system for the model-building simulator.

  2. Technical Note: The CCCma third generation AGCM and its extension into the middle atmosphere

    Directory of Open Access Journals (Sweden)

    J. F. Scinocca

    2008-12-01

    Full Text Available The Canadian Centre for Climate Modelling and Analysis third generation atmospheric general circulation model (AGCM3 is described. The discussion summarizes the details of the complete physics package emphasizing the changes made relative to the second generation version of the model. AGCM3 is the underlying model for applications which include the IPCC fourth assessment, coupled atmosphere-ocean seasonal forecasting, the first generation of the CCCma earth system model (CanESM1, and middle-atmosphere chemistry-climate modelling (CCM. Here we shall focus on issues related to an upwardly extended version of AGCM3, the Canadian Middle-Atmosphere Model (CMAM. The CCM version of CMAM participated in the 2006 WMO/UNEP Scientific Assessment of Ozone Depletion and issues concerning its climate such as the impact of gravity-wave drag, the modelling of a spontaneous QBO, and the seasonality of the breakdown of the Southern Hemisphere polar vortex are discussed here.

  3. Next generation information systems

    Energy Technology Data Exchange (ETDEWEB)

    Limback, Nathan P [Los Alamos National Laboratory; Medina, Melanie A [Los Alamos National Laboratory; Silva, Michelle E [Los Alamos National Laboratory

    2010-01-01

    The Information Systems Analysis and Development (ISAD) Team of the Safeguards Systems Group at Los Alamos National Laboratory (LANL) has been developing web based information and knowledge management systems for sixteen years. Our vision is to rapidly and cost effectively provide knowledge management solutions in the form of interactive information systems that help customers organize, archive, post and retrieve nonproliferation and safeguards knowledge and information vital to their success. The team has developed several comprehensive information systems that assist users in the betterment and growth of their organizations and programs. Through our information systems, users are able to streamline operations, increase productivity, and share and access information from diverse geographic locations. The ISAD team is also producing interactive visual models. Interactive visual models provide many benefits to customers beyond the scope of traditional full-scale modeling. We have the ability to simulate a vision that a customer may propose, without the time constraints of traditional engineering modeling tools. Our interactive visual models can be used to access specialized training areas, controlled areas, and highly radioactive areas, as well as review site-specific training for complex facilities, and asset management. Like the information systems that the ISAD team develops, these models can be shared and accessed from any location with access to the internet. The purpose of this paper is to elaborate on the capabilities of information systems and interactive visual models as well as consider the possibility of combining the two capabilities to provide the next generation of infonnation systems. The collection, processing, and integration of data in new ways can contribute to the security of the nation by providing indicators and information for timely action to decrease the traditional and new nuclear threats. Modeling and simulation tied to comprehensive

  4. Coupled Human-Atmosphere-System Thinking

    Science.gov (United States)

    Schmale, Julia; Chabay, Ilan

    2014-05-01

    With the discovery of fire, humankind started changing the composition of the atmosphere. Beginning with the industrial revolution, this has led to significant environmental problems, mainly air pollution and climate change. While climate change has been recognized as one key challenge of the Anthropocene, air pollution contributes to the top causes of global premature mortality. Air pollution also plays a key role in contamination of ecosystems and bio-magnification of toxins along food chains. Even though emissions leading to air pollution and climate change often originate from the same sources, they are generally perceived and regulated separately. Climate change impacts are global and hence are tackled at an international level. Conversely, air pollution has local to regional impacts and is thus a matter of national or regional legislation. This legislative and policy divide is generally useful, since full integration could lead, for example, to detrimental delays in action against air pollution through protracted international climate negotiations. However, the separation obscures the fact that almost any kind of human activity leads to the simultaneous emission of air pollutants, toxins and long-lived greenhouse gases. The atmosphere functions as a "dump" for human generated gaseous waste, which is then dispersed and transformed, partly chemically and partly micro-physically, perturbing natural processes in the atmosphere and leading to manifold impacts. In addition, air pollutants affect the Earth's radiative balance directly and indirectly, hence affecting climate change, while a changing climate in turn affects air pollution. Current policies often neglect these linkages and favor mitigation in one arena, which sometimes has detrimental effects on the other. One example is domestic wood burning, which though nearly carbon neutral, deteriorates air quality. Moreover, the design of appliances, machinery, or infrastructure generally does not attempt to

  5. Remembrance of phases past: An autoregressive method for generating realistic atmospheres in simulations

    Science.gov (United States)

    Srinath, Srikar; Poyneer, Lisa A.; Rudy, Alexander R.; Ammons, S. M.

    2014-08-01

    The advent of expensive, large-aperture telescopes and complex adaptive optics (AO) systems has strengthened the need for detailed simulation of such systems from the top of the atmosphere to control algorithms. The credibility of any simulation is underpinned by the quality of the atmosphere model used for introducing phase variations into the incident photons. Hitherto, simulations which incorporate wind layers have relied upon phase screen generation methods that tax the computation and memory capacities of the platforms on which they run. This places limits on parameters of a simulation, such as exposure time or resolution, thus compromising its utility. As aperture sizes and fields of view increase the problem will only get worse. We present an autoregressive method for evolving atmospheric phase that is efficient in its use of computation resources and allows for variability in the power contained in frozen flow or stochastic components of the atmosphere. Users have the flexibility of generating atmosphere datacubes in advance of runs where memory constraints allow to save on computation time or of computing the phase at each time step for long exposure times. Preliminary tests of model atmospheres generated using this method show power spectral density and rms phase in accordance with established metrics for Kolmogorov models.

  6. Role of electric discharges in the generation of atmospheric vortices

    Energy Technology Data Exchange (ETDEWEB)

    Sinkevich, O. A., E-mail: oleg.sinkevich@itf.mpei.ac.ru [National Research University “MPEI,” (Russian Federation); Maslov, S. A., E-mail: sergm90@mail.ru [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation); Gusein-zade, N. G., E-mail: ngus@mail.ru [Russian Academy of Sciences, Prokhorov General Physics Institute (Russian Federation)

    2017-02-15

    The existing thermohydrodynamic and hydroelectromagnetic models of tornado are considered. The potentialities of the humid atmosphere as a heat engine generating air vortices are analyzed in detail. The ability of long-term atmospheric electric discharges to form a tornado funnel and create an initial twist of up to 10{sup –3}–10{sup –2} s{sup –1} in it are estimated. The possible effect of a lightning discharge on the initiation and evolution of the tornado is discussed. It is shown that the electric current flowing along the lightning channel can lead to helical instability and generation of a weak primary vortex. The channel formed in the atmosphere by a lightning discharge and the vortex motion of the parent thundercloud can enhance the primary vortex and promote its transformation into a tornado. Possible mechanisms of enhancement of the primary vortex created by a lightning discharge and the possibility of its transformation into a tornado in the postdischarge stage are discussed.

  7. Generation of subnanosecond electron beams in air at atmospheric pressure

    Science.gov (United States)

    Kostyrya, I. D.; Tarasenko, V. F.; Baksht, E. Kh.; Burachenko, A. G.; Lomaev, M. I.; Rybka, D. V.

    2009-11-01

    Optimum conditions for the generation of runaway electron beams with maximum current amplitudes and densities in nanosecond pulsed discharges in air at atmospheric pressure are determined. A supershort avalanche electron beam (SAEB) with a current amplitude of ˜30 A, a current density of ˜20 A/cm2, and a pulse full width at half maximum (FWHM) of ˜100 ps has been observed behind the output foil of an air-filled diode. It is shown that the position of the SAEB current maximum relative to the voltage pulse front exhibits a time shift that varies when the small-size collector is moved over the foil surface.

  8. Rapid Mutation of Spirulina platensis by a New Mutagenesis System of Atmospheric and Room Temperature Plasmas (ARTP) and Generation of a Mutant Library with Diverse Phenotypes

    Science.gov (United States)

    Zhang, Chong; Tan, Yinyee; Jiang, Peixia; Ge, Nan; Heping Li; Xing, Xinhui

    2013-01-01

    In this paper, we aimed to improve the carbohydrate productivity of Spirulina platensis by generating mutants with increased carbohydrate content and growth rate. ARTP was used as a new mutagenesis tool to generate a mutant library of S. platensis with diverse phenotypes. Protocol for rapid mutation of S. platensis by 60 s treatment with helium driven ARTP and high throughput screening method of the mutants using the 96-well microplate and microplate reader was established. A mutant library of 62 mutants was then constructed and ideal mutants were selected out. The characteristics of the mutants after the mutagenesis inclined to be stable after around 9th subculture, where the total mutation frequency and positive mutation frequency in terms of specific growth rate reached 45% and 25%, respectively. The mutants in mutant library showed diverse phenotypes in terms of cell growth rate, carbohydrate content and flocculation intensity. The positive mutation frequency in terms of cellular carbohydrate content with the increase by more than 20% percent than the wild strain was 32.3%. Compared with the wild strain, the representative mutants 3-A10 and 3-B2 showed 40.3% and 78.0% increase in carbohydrate content, respectively, while the mutant 4-B3 showed 10.5% increase in specific growth rate. The carbohydrate contents of the representative mutants were stable during different subcultures, indicating high genetic stability. ARTP was demonstrated to be an effective and non-GMO mutagenesis tool to generate the mutant library for multicellular microalgae. PMID:24319517

  9. Rapid mutation of Spirulina platensis by a new mutagenesis system of atmospheric and room temperature plasmas (ARTP and generation of a mutant library with diverse phenotypes.

    Directory of Open Access Journals (Sweden)

    Mingyue Fang

    Full Text Available In this paper, we aimed to improve the carbohydrate productivity of Spirulina platensis by generating mutants with increased carbohydrate content and growth rate. ARTP was used as a new mutagenesis tool to generate a mutant library of S. platensis with diverse phenotypes. Protocol for rapid mutation of S. platensis by 60 s treatment with helium driven ARTP and high throughput screening method of the mutants using the 96-well microplate and microplate reader was established. A mutant library of 62 mutants was then constructed and ideal mutants were selected out. The characteristics of the mutants after the mutagenesis inclined to be stable after around 9(th subculture, where the total mutation frequency and positive mutation frequency in terms of specific growth rate reached 45% and 25%, respectively. The mutants in mutant library showed diverse phenotypes in terms of cell growth rate, carbohydrate content and flocculation intensity. The positive mutation frequency in terms of cellular carbohydrate content with the increase by more than 20% percent than the wild strain was 32.3%. Compared with the wild strain, the representative mutants 3-A10 and 3-B2 showed 40.3% and 78.0% increase in carbohydrate content, respectively, while the mutant 4-B3 showed 10.5% increase in specific growth rate. The carbohydrate contents of the representative mutants were stable during different subcultures, indicating high genetic stability. ARTP was demonstrated to be an effective and non-GMO mutagenesis tool to generate the mutant library for multicellular microalgae.

  10. Atmospheric wind field conditions generated by active grids

    Science.gov (United States)

    Knebel, Pascal; Kittel, Achim; Peinke, Joachim

    2011-08-01

    An active grid for turbulence generation of several rotatable axes with surmounted vanes that can be driven via stepper or servo motors is presented. We investigate the impact of different excitation protocols for the grid. Using such protocols that already have the intermittent structure of turbulence, higher intermittent flows can be achieved. This concept can also be used to generate turbulent flows of high turbulence intensities (>25%) exhibiting integral length scales beyond the typical size of the test section of the wind tunnel. Similar two-point correlations measured by the intermittent statistics of velocity increments that are characteristic for flows of high Reynolds number, i.e. in the atmospheric boundary layer, can be reproduced.

  11. Subtarget Effect on Laser Plasma Generated by Transversely Excited Atmospheric CO2 Laser at Atmospheric Gas Pressure

    Science.gov (United States)

    Kagawa, Kiichiro; Lie, Tjung Jie; Hedwig, Rinda; Abdulmajid, Syahrun Nur; Suliyanti, Maria Margaretha; Kurniawan, Hendrik

    2000-05-01

    An experimental study has been carried out on the dynamical process taking place in the laser plasma generated by Transversely Excited Atmospheric CO2 laser (100 mJ, 50 ns) irradiation of a soft sample at surrounding helium pressure of 1 atm. It is shown that the presence of a copper subtarget behind the soft sample is crucial in raising the gushing speed of the atoms to the level adequate for the generation of shock wave laser plasma even at atmospheric pressure. It is also found that the time profiles of spatially integrated emission intensity of the target’s atoms and gas atoms exhibit a characteristic dynamical process that consists of successive excitation and cooling stages even at such a high pressure, which is typical of shock wave laser plasma. It is therefore suggested that the generation of the laser plasma at atmospheric pressure is more likely due to the shock wave mechanism than to the widely known breakdown mechanism. Initial spectrochemical analysis of water from the blow off of a boiler system was also carried out, showing a detection limit of as low as 5 ppm for calcium.

  12. The Panama fossil power plants generation system: Atmospheric pollution, general and legal aspects; El sistema de generacion termoelectrico en Panama: Contaminacion atmosferica, aspectos generales y legales

    Energy Technology Data Exchange (ETDEWEB)

    Milciades, Concepcion [Instituto de Recursos Hidraulicos y Electrificacion, (Panama)

    1996-12-31

    The Thermal electric energy resource of Panama is administered by four Regional Managements and a group of Regional Systems comprising the fossil power plants supplying electric energy to the country`s marginal areas. The characteristics of the different fuels used in these fossil power plants, the results of the assessment of the polluting particles and sulfur and nitrogen oxides are presented. Finally, the alleviation measures and the environmental legislation implanted in these power plants are also presented [Espanol] El parque termico de Panama es administrado por cuatro Gerencias Regionales y un conjunto de Sistemas Regionales que comprenden las plantas termicas de menor capacidad destinadas a suplir de energia a las areas marginadas del pais. Se presentan las caracteristicas de los diferentes combustibles utilizados en estas unidades termicas; los resultados de las mediciones de particulas contaminantes y de oxidos de azufre y oxidos de nitrogeno. Por ultimo se presentan las medidas de mitigacion y legislacion ambiental implantadas en estas centrales termoelectricas

  13. Technical notes for the conceptual design for an atmospheric fluidized-bed direct combustion power generating plant. [570 MWe plant

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-04-01

    The design, arrangement, thermodynamics, and economics of a 592 MW(e) (nominal gross) electric power generating plant equipped with a Babcock and Wilcox Company (B and W) atmospheric fluidized bed (AFB) boiler are described. Information is included on capital and operating costs, process systems, electrical systems, control and instrumentation, and environmental systems. This document represents a portion of an overall report describing the conceptual designs of two atmospheric fluidized bed boilers and balance of plants for the generation of electric power and the analysis and comparison of these conceptual designs to a conventional pulverized coal-fired electric power generation plant equipped with a wet limestone flue gas desulfurization system.

  14. Technical notes for the conceptual design for an atmospheric fluidized-bed direct combustion power generating plant. [570 MWe plant

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-04-01

    The design, arrangement, thermodynamics, and economics of a 578 MW(e) (nominal gross) electric power generating plant equipped with a Foster Wheeler Energy Corporation (FWEC) atmospheric fluidized bed (AFB) boiler are described. Information is included on capital and operating costs, process systems, electrical systems, control and instrumentation, and environmental systems. This document represents a portion of an overall report describing the conceptual designs of two atmospheric fluidized bed boilers and balance of plants for the generation of electric power and the analysis and comparison of these conceptual designs to a conventional pulverized coal-fired electric power generation plant equipped with a wet limestone flue gas desulfurization system.

  15. Atmospheric cloud physics thermal systems analysis

    Science.gov (United States)

    1977-01-01

    Engineering analyses performed on the Atmospheric Cloud Physics (ACPL) Science Simulator expansion chamber and associated thermal control/conditioning system are reported. Analyses were made to develop a verified thermal model and to perform parametric thermal investigations to evaluate systems performance characteristics. Thermal network representations of solid components and the complete fluid conditioning system were solved simultaneously using the Systems Improved Numerical Differencing Analyzer (SINDA) computer program.

  16. Mars Entry Atmospheric Data System Modeling, Calibration, and Error Analysis

    Science.gov (United States)

    Karlgaard, Christopher D.; VanNorman, John; Siemers, Paul M.; Schoenenberger, Mark; Munk, Michelle M.

    2014-01-01

    The Mars Science Laboratory (MSL) Entry, Descent, and Landing Instrumentation (MEDLI)/Mars Entry Atmospheric Data System (MEADS) project installed seven pressure ports through the MSL Phenolic Impregnated Carbon Ablator (PICA) heatshield to measure heatshield surface pressures during entry. These measured surface pressures are used to generate estimates of atmospheric quantities based on modeled surface pressure distributions. In particular, the quantities to be estimated from the MEADS pressure measurements include the dynamic pressure, angle of attack, and angle of sideslip. This report describes the calibration of the pressure transducers utilized to reconstruct the atmospheric data and associated uncertainty models, pressure modeling and uncertainty analysis, and system performance results. The results indicate that the MEADS pressure measurement system hardware meets the project requirements.

  17. Hydrogen storage and generation system

    Science.gov (United States)

    Dentinger, Paul M.; Crowell, Jeffrey A. W.

    2010-08-24

    A system for storing and generating hydrogen generally and, in particular, a system for storing and generating hydrogen for use in an H.sub.2/O.sub.2 fuel cell. The hydrogen storage system uses the beta particles from a beta particle emitting material to degrade an organic polymer material to release substantially pure hydrogen. In a preferred embodiment of the invention, beta particles from .sup.63Ni are used to release hydrogen from linear polyethylene.

  18. The Aussat second generation system

    Science.gov (United States)

    Nowland, Wayne

    This paper outlines the design of Aussat's second generation satellites, and overviews the proposed service applications for which the system has been designed. Market data are presented for Aussat's planned mobile satellite services, together with an outline of the associated mobile satellite terminal development program. The unique procurement arrangements for which Aussat is adopting its second generation system, including the requirements for 'turnkey' in-orbit delivery and contractor-supplied risk management, are also described.

  19. Generative electronic background music system

    Energy Technology Data Exchange (ETDEWEB)

    Mazurowski, Lukasz [Faculty of Computer Science, West Pomeranian University of Technology in Szczecin, Zolnierska Street 49, Szczecin, PL (Poland)

    2015-03-10

    In this short paper-extended abstract the new approach to generation of electronic background music has been presented. The Generative Electronic Background Music System (GEBMS) has been located between other related approaches within the musical algorithm positioning framework proposed by Woller et al. The music composition process is performed by a number of mini-models parameterized by further described properties. The mini-models generate fragments of musical patterns used in output composition. Musical pattern and output generation are controlled by container for the mini-models - a host-model. General mechanism has been presented including the example of the synthesized output compositions.

  20. Modeling Turbulence Generation in the Atmospheric Surface and Boundary Layers

    Science.gov (United States)

    2015-10-01

    index. In the boundary layer, atmospheric temperature fluctuations are primarily responsible for the variations in refractive index at ultraviolet...parameterization of the atmospheric emissivity, in the early 1980s a parallel study of the SEB was conducted by the US Army Waterways Experiment Station...period of rotation of the atmosphere can be defined as TI = 2π/fc. At most mid- latitude locations this period is approximately 17 h. This quantity is

  1. Piezoelectric transformers for low-voltage generation of gas discharges and ionic winds in atmospheric air

    Science.gov (United States)

    Johnson, Michael J.; Go, David B.

    2015-12-01

    To generate a gas discharge (plasma) in atmospheric air requires an electric field that exceeds the breakdown threshold of ˜30 kV/cm. Because of safety, size, or cost constraints, the large applied voltages required to generate such fields are often prohibitive for portable applications. In this work, piezoelectric transformers are used to amplify a low input applied voltage (corona-like discharges on its corners or on adjacent electrodes. In the proper configuration, these discharges can be used to generate a bulk air flow called an ionic wind. In this work, PT-driven discharges are characterized by measuring the discharge current and the velocity of the induced ionic wind with ionic winds generated using input voltages as low as 7 V. The characteristics of the discharge change as the input voltage increases; this modifies the resonance of the system and subsequent required operating parameters.

  2. The global atmospheric environment for the next generation

    NARCIS (Netherlands)

    Dentener, F.; Stevenson, D.; Ellingsen, K.; Noije, van T.; Schultz, M.; Amann, M.; Atherton, C.; Bell, N.; Bergmann, D.; Bey, I.; Bouwman, L.; Butler, T.; Cofala, J.; Collins, B.; Drevet, J.; Doherty, R.; Eickhout, B.; Eskes, H.; Fiore, A.; Gauss, M.; Hauglustaine, D.; Horowitz, L.; Isaksen, I.S.A.; Josse, B.; Lawrence, M.; Krol, M.C.; Lamarque, J.F.; Montanaro, V.; Müller, J.F.; Peuch, V.H.; Pitari, G.; Pyle, J.; Rast, S.; Rodriguez, J.; Sanderson, M.; Savage, N.H.; Shindell, D.; Strahan, S.; Szopa, S.; Sudo, K.; Dingenen, van R.; Wild, O.; Zeng, G.

    2006-01-01

    Air quality, ecosystem exposure to nitrogen deposition, and climate change are intimately coupled problems: we assess changes in the global atmospheric environment between 2000 and 2030 using 26 state-of-the-art global atmospheric chemistry models and three different emissions scenarios. The first (

  3. Memory efficient atmospheric effects modeling for infrared scene generators

    Science.gov (United States)

    Kavak, Çaǧlar; Özsaraç, Seçkin

    2015-05-01

    The infrared (IR) energy radiated from any source passes through the atmosphere before reaching the sensor. As a result, the total signature captured by the IR sensor is significantly modified by the atmospheric effects. The dominant physical quantities that constitute the mentioned atmospheric effects are the atmospheric transmittance and the atmospheric path radiance. The incoming IR radiation is attenuated by the transmittance and path radiance is added on top of the attenuated radiation. In IR scene simulations OpenGL is widely used for rendering purposes. In the literature there are studies, which model the atmospheric effects in an IR band using OpenGLs exponential fog model as suggested by Beers law. In the standard pipeline of OpenGL, the related fog model needs single equivalent OpenGL variables for the transmittance and path radiance, which actually depend on both the distance between the source and the sensor and also on the wavelength of interest. However, in the conditions where the range dependency cannot be modeled as an exponential function, it is not accurate to replace the atmospheric quantities with a single parameter. The introduction of OpenGL Shading Language (GLSL) has enabled the developers to use the GPU more flexible. In this paper, a novel method is proposed for the atmospheric effects modeling using the least squares estimation with polynomial fitting by programmable OpenGL shader programs built with GLSL. In this context, a radiative transfer model code is used to obtain the transmittance and path radiance data. Then, polynomial fits are computed for the range dependency of these variables. Hence, the atmospheric effects model data that will be uploaded in the GPU memory is significantly reduced. Moreover, the error because of fitting is negligible as long as narrow IR bands are used.

  4. Towards Next Generation BI Systems

    DEFF Research Database (Denmark)

    Varga, Jovan; Romero, Oscar; Pedersen, Torben Bach

    2014-01-01

    Next generation Business Intelligence (BI) systems require integration of heterogeneous data sources and a strong user-centric orientation. Both needs entail machine-processable metadata to enable automation and allow end users to gain access to relevant data for their decision making processes...

  5. The RTSS Image Generation System

    NARCIS (Netherlands)

    Alvermann, K.; Graeber, S.; Mager, J.W.L.J.; Smith, M.H.

    1996-01-01

    Main market demands for the visual system of a simulator are photorealism and low latency time. RTSS, a general purpose image generation module developed within the European ESPRIT project HAMLET, can meet these demands through the use of High Performance Computing technology. This technology provid

  6. Atmospheric Profiling Snthetic observation System(APSOS) - a system for whole atmosphere, purpose and preliminary observation

    Science.gov (United States)

    Lu, Daren; Pan, Weilin; Wang, Yinan

    2016-07-01

    To understand the vertical coupling processes between the troposphere, stratosphere, mesosphere and lower thermosphere with high vertical resolution and temporal resolution, an observation system consisted of multi-lidars, a W-band Doppler radar, and a THz spectrometer has been developing starting from 2012. This system is developed to observer the multiple atmospheric parameters, include high clouds, aerosols, CO2, SO2, NO2, water vapor, ozone, atmospheric temperature and wind, sodium atomic layer, in different height ranges, with vertical resolution of tens to hundreds meters and temporal resolution of several to tens minutes. In addition, the simultaneous observation with high cloud radar will enhance the ability of quantitative retrieval of middle and upper atmospheric observation with combined retrieval of cloud micro-physical characteristics and other atmospheric parameters above the cloud layer. As the cirrus cloud occupied about 50% of earth coverage, this ability will increase the whole atmosphere observation ability obviously. During last 5 years. We have finished each unit of the system and have revealed their targets separately. Temperature profile has been observed from 30 to 110 km, ozone up to 50 km, etc. In spring of 2016, we will have preliminary integrated observation in Eastern China, the Huainan Observatory of the Institute of Atmospheric Physics, CAS. In the end of 2016, the system will be implemented at Yangbajing Cosmic Ray Observatory, CAS, near Lasa, Tibetan Plateau. Some preliminary results from Huainan observation will be presented in this presentation. This project is founded by NSFC.

  7. Atmospheric dc discharges with miniature gas flow as microplasma generation method

    Energy Technology Data Exchange (ETDEWEB)

    Yokoyama, Takuma; Hamada, Shuhei; Ibuka, Shinji; Yasuoka, Koichi; Ishii, Shozo [Department of Electrical and Electronic Engineering, Tokyo Institute of Technology, Tokyo 152-8552 (Japan)

    2005-06-07

    An atmospheric microplasma is generated by direct-current (dc) discharge in air with a miniature gas flow through a nozzle, which limits plasma volume. Two discharge modes appear in a nozzle-to-mesh electrode system with helium or argon. One is a repetitive pulsed discharge with a current of 10-30 mA and a short pulse width. The fast pulsed current is powered by electric charges stored in the parasitic capacitance, which depends on the spatial arrangement of the electrodes and the power leads. The pulsed discharge makes it possible to develop a discharge scheme for microplasma generation without a high-voltage pulse generator. The other is a sustained dc discharge, which develops with increasing applied voltage. In the case of helium, a glow discharge configuration is observed with a positive column and a layered structure near the cathode. The length of the positive column is affected by electrode separation and gas flow rate.

  8. 40 CFR 53.22 - Generation of test atmospheres.

    Science.gov (United States)

    2010-07-01

    ... zero air free of contaminants likely to cause a detectable response on the test analyzer. Table B-2... Tentative method of analysis for H2 S content of the atmosphere, p. 426, reference 5. Methane Cylinder of... 1. Use an NO 2 analyzer calibrated with a gravimetrically calibrated permeation device.2. Use an...

  9. Toward GEOS-6, A Global Cloud System Resolving Atmospheric Model

    Science.gov (United States)

    Putman, William M.

    2010-01-01

    NASA is committed to observing and understanding the weather and climate of our home planet through the use of multi-scale modeling systems and space-based observations. Global climate models have evolved to take advantage of the influx of multi- and many-core computing technologies and the availability of large clusters of multi-core microprocessors. GEOS-6 is a next-generation cloud system resolving atmospheric model that will place NASA at the forefront of scientific exploration of our atmosphere and climate. Model simulations with GEOS-6 will produce a realistic representation of our atmosphere on the scale of typical satellite observations, bringing a visual comprehension of model results to a new level among the climate enthusiasts. In preparation for GEOS-6, the agency's flagship Earth System Modeling Framework [JDl] has been enhanced to support cutting-edge high-resolution global climate and weather simulations. Improvements include a cubed-sphere grid that exposes parallelism; a non-hydrostatic finite volume dynamical core, and algorithm designed for co-processor technologies, among others. GEOS-6 represents a fundamental advancement in the capability of global Earth system models. The ability to directly compare global simulations at the resolution of spaceborne satellite images will lead to algorithm improvements and better utilization of space-based observations within the GOES data assimilation system

  10. Atmospheric turbulence and sensor system effects on biometric algorithm performance

    Science.gov (United States)

    Espinola, Richard L.; Leonard, Kevin R.; Byrd, Kenneth A.; Potvin, Guy

    2015-05-01

    Biometric technologies composed of electro-optical/infrared (EO/IR) sensor systems and advanced matching algorithms are being used in various force protection/security and tactical surveillance applications. To date, most of these sensor systems have been widely used in controlled conditions with varying success (e.g., short range, uniform illumination, cooperative subjects). However the limiting conditions of such systems have yet to be fully studied for long range applications and degraded imaging environments. Biometric technologies used for long range applications will invariably suffer from the effects of atmospheric turbulence degradation. Atmospheric turbulence causes blur, distortion and intensity fluctuations that can severely degrade image quality of electro-optic and thermal imaging systems and, for the case of biometrics technology, translate to poor matching algorithm performance. In this paper, we evaluate the effects of atmospheric turbulence and sensor resolution on biometric matching algorithm performance. We use a subset of the Facial Recognition Technology (FERET) database and a commercial algorithm to analyze facial recognition performance on turbulence degraded facial images. The goal of this work is to understand the feasibility of long-range facial recognition in degraded imaging conditions, and the utility of camera parameter trade studies to enable the design of the next generation biometrics sensor systems.

  11. Solar Thermal Electricity Generating System

    Science.gov (United States)

    Mishra, Sambeet; Tripathy, Pratyasha

    2012-08-01

    A Solar Thermal Electricity generating system also known as Solar Thermal Power plant is an emerging renewable energy technology, where we generate the thermal energy by concentrating and converting the direct solar radiationat medium/high temperature (300∫C ñ 800∫C). The resulting thermal energy is then used in a thermodynamic cycleto produce electricity, by running a heat engine, which turns a generator to make electricity. Solar thermal power is currently paving the way for the most cost-effective solar technology on a large scale and is heading to establish a cleaner, pollution free and secured future. Photovoltaic (PV) and solar thermal technologies are two main ways of generating energy from the sun, which is considered the inexhaustible source of energy. PV converts sunlight directly into electricity whereas in Solar thermal technology, heat from the sun's rays is concentrated to heat a fluid, whose steam powers a generator that produces electricity. It is similar to the way fossil fuel-burning power plants work except that the steam is produced by the collected heat rather than from the combustion of fossil fuels. In order to generate electricity, five major varieties of solar thermal technologies used are:* Parabolic Trough Solar Electric Generating System (SEGS).* Central Receiver Power Plant.* Solar Chimney Power Plant.* Dish Sterling System.* Solar Pond Power Plant.Most parts of India,Asia experiences a clear sunny weather for about 250 to 300 days a year, because of its location in the equatorial sun belt of the earth, receiving fairly large amount of radiation as compared to many parts of the world especially Japan, Europe and the US where development and deployment of solar technologies is maximum.Whether accompanied with this benefit or not, usually we have to concentrate the solar radiation in order to compensate for the attenuation of solar radiation in its way to earthís surface, which results in from 63,2 GW/m2 at the Sun to 1 kW/m2 at

  12. Piezoelectric transformers for low-voltage generation of gas discharges and ionic winds in atmospheric air

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Michael J. [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indianapolis 46556 (United States); Go, David B., E-mail: dgo@nd.edu [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indianapolis 46556 (United States); Department of Chemical and Biomolecular Engineering, University of Notre Dame, Notre Dame, Indianapolis 46556 (United States)

    2015-12-28

    To generate a gas discharge (plasma) in atmospheric air requires an electric field that exceeds the breakdown threshold of ∼30 kV/cm. Because of safety, size, or cost constraints, the large applied voltages required to generate such fields are often prohibitive for portable applications. In this work, piezoelectric transformers are used to amplify a low input applied voltage (<30 V) to generate breakdown in air without the need for conventional high-voltage electrical equipment. Piezoelectric transformers (PTs) use their inherent electromechanical resonance to produce a voltage amplification, such that the surface of the piezoelectric exhibits a large surface voltage that can generate corona-like discharges on its corners or on adjacent electrodes. In the proper configuration, these discharges can be used to generate a bulk air flow called an ionic wind. In this work, PT-driven discharges are characterized by measuring the discharge current and the velocity of the induced ionic wind with ionic winds generated using input voltages as low as 7 V. The characteristics of the discharge change as the input voltage increases; this modifies the resonance of the system and subsequent required operating parameters.

  13. Ground-based acoustic parametric generator impact on the atmosphere and ionosphere in an active experiment

    Science.gov (United States)

    Rapoport, Yuriy G.; Cheremnykh, Oleg K.; Koshovy, Volodymyr V.; Melnik, Mykola O.; Ivantyshyn, Oleh L.; Nogach, Roman T.; Selivanov, Yuriy A.; Grimalsky, Vladimir V.; Mezentsev, Valentyn P.; Karataeva, Larysa M.; Ivchenko, Vasyl. M.; Milinevsky, Gennadi P.; Fedun, Viktor N.; Tkachenko, Eugen N.

    2017-01-01

    We develop theoretical basics of active experiments with two beams of acoustic waves, radiated by a ground-based sound generator. These beams are transformed into atmospheric acoustic gravity waves (AGWs), which have parameters that enable them to penetrate to the altitudes of the ionospheric E and F regions where they influence the electron concentration of the ionosphere. Acoustic waves are generated by the ground-based parametric sound generator (PSG) at the two close frequencies. The main idea of the experiment is to design the output parameters of the PSG to build a cascade scheme of nonlinear wave frequency downshift transformations to provide the necessary conditions for their vertical propagation and to enable penetration to ionospheric altitudes. The PSG generates sound waves (SWs) with frequencies f1 = 600 and f2 = 625 Hz and large amplitudes (100-420 m s-1). Each of these waves is modulated with the frequency of 0.016 Hz. The novelty of the proposed analytical-numerical model is due to simultaneous accounting for nonlinearity, diffraction, losses, and dispersion and inclusion of the two-stage transformation (1) of the initial acoustic waves to the acoustic wave with the difference frequency Δf = f2 - f1 in the altitude ranges 0-0.1 km, in the strongly nonlinear regime, and (2) of the acoustic wave with the difference frequency to atmospheric acoustic gravity waves with the modulational frequency in the altitude ranges 0.1-20 km, which then reach the altitudes of the ionospheric E and F regions, in a practically linear regime. AGWs, nonlinearly transformed from the sound waves, launched by the two-frequency ground-based sound generator can increase the transparency of the ionosphere for the electromagnetic waves in HF (MHz) and VLF (kHz) ranges. The developed theoretical model can be used for interpreting an active experiment that includes the PSG impact on the atmosphere-ionosphere system, measurements of electromagnetic and acoustic fields, study of

  14. Implementation of optimum solar electricity generating system

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Balbir Singh Mahinder, E-mail: balbir@petronas.com.my; Karim, Samsul Ariffin A., E-mail: samsul-ariffin@petronas.com.my [Department of Fundamental and Applied Sciences, Universiti Teknologi PETRONAS, 31750 Bandar Seri Iskandar, Perak (Malaysia); Sivapalan, Subarna, E-mail: subarna-sivapalan@petronas.com.my [Department of Management and Humanities, Universiti Teknologi PETRONAS, 31750 Bandar Seri Iskandar, Perak (Malaysia); Najib, Nurul Syafiqah Mohd; Menon, Pradeep [Department of Electrical and Electronics Engineering, Universiti Teknologi PETRONAS, 31750 Bandar Seri Iskandar, Perak (Malaysia)

    2014-10-24

    Under the 10{sup th} Malaysian Plan, the government is expecting the renewable energy to contribute approximately 5.5% to the total electricity generation by the year 2015, which amounts to 98MW. One of the initiatives to ensure that the target is achievable was to establish the Sustainable Energy Development Authority of Malaysia. SEDA is given the authority to administer and manage the implementation of the feed-in tariff (FiT) mechanism which is mandated under the Renewable Energy Act 2011. The move to establish SEDA is commendable and the FiT seems to be attractive but there is a need to create awareness on the implementation of the solar electricity generating system (SEGS). In Malaysia, harnessing technologies related to solar energy resources have great potential for implementation. However, the main issue that plagues the implementation of SEGS is the intermittent nature of this source of energy. The availability of sunlight is during the day time, and there is a need for electrical energy storage system, so that there is electricity available during the night time as well. The meteorological condition such as clouds, haze and pollution affects the SEGS as well. The PV based SEGS is seems to be promising electricity generating system that can contribute towards achieving the 5.5% target and will be able to minimize the negative effects of utilizing fossil fuels for electricity generation on the environment. Malaysia is committed to Kyoto Protocol, which emphasizes on fighting global warming by achieving stabilization of greenhouse gas concentrations in the atmosphere at a level that would prevent dangerous anthropogenic interference with the climate system. In this paper, the technical aspects of the implementation of optimum SEGS is discussed, especially pertaining to the positioning of the PV panels.

  15. Implementation of optimum solar electricity generating system

    Science.gov (United States)

    Singh, Balbir Singh Mahinder; Sivapalan, Subarna; Najib, Nurul Syafiqah Mohd; Menon, Pradeep; Karim, Samsul Ariffin A.

    2014-10-01

    Under the 10th Malaysian Plan, the government is expecting the renewable energy to contribute approximately 5.5% to the total electricity generation by the year 2015, which amounts to 98MW. One of the initiatives to ensure that the target is achievable was to establish the Sustainable Energy Development Authority of Malaysia. SEDA is given the authority to administer and manage the implementation of the feed-in tariff (FiT) mechanism which is mandated under the Renewable Energy Act 2011. The move to establish SEDA is commendable and the FiT seems to be attractive but there is a need to create awareness on the implementation of the solar electricity generating system (SEGS). In Malaysia, harnessing technologies related to solar energy resources have great potential for implementation. However, the main issue that plagues the implementation of SEGS is the intermittent nature of this source of energy. The availability of sunlight is during the day time, and there is a need for electrical energy storage system, so that there is electricity available during the night time as well. The meteorological condition such as clouds, haze and pollution affects the SEGS as well. The PV based SEGS is seems to be promising electricity generating system that can contribute towards achieving the 5.5% target and will be able to minimize the negative effects of utilizing fossil fuels for electricity generation on the environment. Malaysia is committed to Kyoto Protocol, which emphasizes on fighting global warming by achieving stabilization of greenhouse gas concentrations in the atmosphere at a level that would prevent dangerous anthropogenic interference with the climate system. In this paper, the technical aspects of the implementation of optimum SEGS is discussed, especially pertaining to the positioning of the PV panels.

  16. Compact 180-kV Marx generator triggered in atmospheric air by femtosecond laser filaments

    Science.gov (United States)

    Arantchouk, L.; Point, G.; Brelet, Y.; Larour, J.; Carbonnel, J.; André, Y.-B.; Mysyrowicz, A.; Houard, A.

    2014-03-01

    We developed a compact Marx generator triggered in atmospheric air by a single femtosecond laser beam undergoing filamentation. Voltage pulses of 180 kV could be generated with a subnanosecond jitter. The same laser beam was also used to initiate simultaneously guided discharges up to 21 cm long at the output of the generator.

  17. The Global Atmospheric Environment for the Next Generation

    Energy Technology Data Exchange (ETDEWEB)

    Dentener, F; Stevenson, D; Ellingsen, K; van Joije, T; Schultz, M; Amann, M; Atherton, C; Bell, N; Bergmann, D; Bey, I; Bouwman, L; Butler, T; Cofala, J; Collins, B; Drevet, J; Doherty, R; Eickhout, B; Eskes, H; Fiore, A; Gauss, M; Hauglustaine, D; Horowitz, L; Isaksen, I A; Josse, B; Lawrence, M; Krol, M; Lamarque, J F; Montanaro, V; Muller, J F; Peuch, V H; Pitari, G; Pyle, J; Rast, S; Rodriguez, J; Sanderson, M; Savage, N H; Shindell, D; Strahan, S; Szopa, S; Sudo, K; Van Dingenen, R; Wild, O; Zeng, G

    2005-12-07

    Air quality, ecosystem exposure to nitrogen deposition, and climate change are intimately coupled problems: we assess changes in the global atmospheric environment between 2000 and 2030 using twenty-five state-of-the-art global atmospheric chemistry models and three different emissions scenarios. The first (CLE) scenario reflects implementation of current air quality legislation around the world, whilst the second (MFR) represents a more optimistic case in which all currently feasible technologies are applied to achieve maximum emission reductions. We contrast these scenarios with the more pessimistic IPCC SRES A2 scenario. Ensemble simulations for the year 2000 are consistent among models, and show a reasonable agreement with surface ozone, wet deposition and NO{sub 2} satellite observations. Large parts of the world are currently exposed to high ozone concentrations, and high depositions of nitrogen to ecosystems. By 2030, global surface ozone is calculated to increase globally by 1.5 {+-} 1.2 ppbv (CLE), and 4.3 {+-} 2.2 ppbv (A2). Only the progressive MFR scenario will reduce ozone by -2.3 {+-} 1.1 ppbv. The CLE and A2 scenarios project further increases in nitrogen critical loads, with particularly large impacts in Asia where nitrogen emissions and deposition are forecast to increase by a factor of 1.4 (CLE) to 2 (A2). Climate change may modify surface ozone by -0.8 {+-} 0.6 ppbv, with larger decreases over sea than over land. This study shows the importance of enforcing current worldwide air quality legislation, and the major benefits of going further. Non-attainment of these air quality policy objectives, such as expressed by the SRES-A2 scenario, would further degrade the global atmospheric environment.

  18. NEXT GENERATION TURBINE SYSTEM STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Frank Macri

    2002-02-28

    Rolls-Royce has completed a preliminary design and marketing study under a Department of Energy (DOE) cost shared contract (DE-AC26-00NT40852) to analyze the feasibility of developing a clean, high efficiency, and flexible Next Generation Turbine (NGT) system to meet the power generation market needs of the year 2007 and beyond. Rolls-Royce evaluated the full range of its most advanced commercial aerospace and aeroderivative engines alongside the special technologies necessary to achieve the aggressive efficiency, performance, emissions, economic, and flexibility targets desired by the DOE. Heavy emphasis was placed on evaluating the technical risks and the economic viability of various concept and technology options available. This was necessary to ensure the resulting advanced NGT system would provide extensive public benefits and significant customer benefits without introducing unacceptable levels of technical and operational risk that would impair the market acceptance of the resulting product. Two advanced cycle configurations were identified as offering significant advantages over current combined cycle products available in the market. In addition, balance of plant (BOP) technologies, as well as capabilities to improve the reliability, availability, and maintainability (RAM) of industrial gas turbine engines, have been identified. A customer focused survey and economic analysis of a proposed Rolls-Royce NGT product configuration was also accomplished as a part of this research study. The proposed Rolls-Royce NGT solution could offer customers clean, flexible power generation systems with very high efficiencies, similar to combined cycle plants, but at a much lower specific cost, similar to those of simple cycle plants.

  19. Next generation sensors and systems

    CERN Document Server

    2016-01-01

    Written by experts in their area of research, this book has outlined the current status of the fundamentals and analytical concepts, modelling and design issues, technical details and practical applications of different types of sensors and discussed about the trends of next generation of sensors and systems happening in the area of Sensing technology. This book will be useful as a reference book for engineers and scientist especially the post-graduate students find will this book as reference book for their research on wearable sensors, devices and technologies.  .

  20. NOAA/NCEP Global Forecast System (GFS) Atmospheric Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — U.S. National Oceanic and Atmospheric Administration (NOAA) National Centers for Environmental Prediction (NCEP) Global Forecast System (GFS) numerical weather...

  1. The global atmospheric environment for the next generation.

    Science.gov (United States)

    Dentener, F; Stevenson, D; Ellingsen, K; Van Noije, T; Schultz, M; Amann, M; Atherton, C; Bell, N; Bergmann, D; Bey, I; Bouwman, L; Butler, T; Cofala, J; Collins, B; Drevet, J; Doherty, R; Eickhout, B; Eskes, H; Fiore, A; Gauss, M; Hauglustaine, D; Horowitz, L; Isaksen, I S A; Josse, B; Lawrence, M; Krol, M; Lamarque, J F; Montanaro, V; Müller, J F; Peuch, V H; Pitari, G; Pyle, J; Rast, S; Rodriguez, I; Sanderson, M; Savage, N H; Shindell, D; Strahan, S; Szopa, S; Sudo, K; Van Dingenen, R; Wild, O; Zeng, G

    2006-06-01

    Air quality, ecosystem exposure to nitrogen deposition, and climate change are intimately coupled problems: we assess changes in the global atmospheric environment between 2000 and 2030 using 26 state-of-the-art global atmospheric chemistry models and three different emissions scenarios. The first (CLE) scenario reflects implementation of current air quality legislation around the world, while the second (MFR) represents a more optimistic case in which all currently feasible technologies are applied to achieve maximum emission reductions. We contrast these scenarios with the more pessimistic IPCC SRES A2 scenario. Ensemble simulations for the year 2000 are consistent among models and show a reasonable agreement with surface ozone, wet deposition, and NO2 satellite observations. Large parts of the world are currently exposed to high ozone concentrations and high deposition of nitrogen to ecosystems. By 2030, global surface ozone is calculated to increase globally by 1.5 +/- 1.2 ppb (CLE) and 4.3 +/- 2.2 ppb (A2), using the ensemble mean model results and associated +/-1 sigma standard deviations. Only the progressive MFR scenario will reduce ozone, by -2.3 +/- 1.1 ppb. Climate change is expected to modify surface ozone by -0.8 +/- 0.6 ppb, with larger decreases over sea than over land. Radiative forcing by ozone increases by 63 +/- 15 and 155 +/- 37 mW m(-2) for CLE and A2, respectively, and decreases by -45 +/- 15 mW m(-2) for MFR. We compute that at present 10.1% of the global natural terrestrial ecosystems are exposed to nitrogen deposition above a critical load of 1 g N m(-2) yr(-1). These percentages increase by 2030 to 15.8% (CLE), 10.5% (MFR), and 25% (A2). This study shows the importance of enforcing current worldwide air quality legislation and the major benefits of going further. Nonattainment of these air quality policy objectives, such as expressed by the SRES-A2 scenario, would further degrade the global atmospheric environment.

  2. Lifting Entry & Atmospheric Flight (LEAF) System Concept Applications at Solar System Bodies With an Atmosphere

    Science.gov (United States)

    Lee, Greg; Polidan, Ronald; Ross, Floyd; Sokol, Daniel; Warwick, Steve

    2015-11-01

    Northrop Grumman and L’Garde have continued the development of a hypersonic entry, semi-buoyant, maneuverable platform capable of performing long-duration (months to a year) in situ and remote measurements at any solar system body that possesses an atmosphere.The Lifting Entry & Atmospheric Flight (LEAF) family of vehicles achieves this capability by using a semi-buoyant, ultra-low ballistic coefficient vehicle whose lifting entry allows it to enter the atmosphere without an aeroshell. The mass savings realized by eliminating the heavy aeroshell allows significantly more payload to be accommodated by the platform for additional science collection and return.In this presentation, we discuss the application of the LEAF system at various solar system bodies: Venus, Titan, Mars, and Earth. We present the key differences in platform design as well as operational differences required by the various target environments. The Venus implementation includes propulsive capability to reach higher altitudes during the day and achieves full buoyancy in the mid-cloud layer of Venus’ atmosphere at night.Titan also offers an attractive operating environment, allowing LEAF designs that can target low or medium altitude operations, also with propulsive capabilities to roam within each altitude regime. The Mars version is a glider that descends gradually, allowing targeted delivery of payloads to the surface or high resolution surface imaging. Finally, an Earth version could remain in orbit in a stowed state until activated, allowing rapid response type deployments to any region of the globe.

  3. Solar system astrophysics planetary atmospheres and the outer solar system

    CERN Document Server

    Milone, Eugene F

    2014-01-01

    The second edition of Solar System Astrophysics: Planetary Atmospheres and the Outer Solar System provides a timely update of our knowledge of planetary atmospheres and the bodies of the outer solar system and their analogs in other planetary systems. This volume begins with an expanded treatment of the physics, chemistry, and meteorology of the atmospheres of the Earth, Venus, and Mars, moving on to their magnetospheres and then to a full discussion of the gas and ice giants and their properties. From here, attention switches to the small bodies of the solar system, beginning with the natural satellites. Then comets, meteors, meteorites, and asteroids are discussed in order, and the volume concludes with the origin and evolution of our solar system. Finally, a fully revised section on extrasolar planetary systems puts the development of our system in a wider and increasingly well understood galactic context. All of the material is presented within a framework of historical importance. This book and its sist...

  4. Third-Order Harmonic Generation in Atmospheric Air with Focused Intense Femtosecond Laser Pulses

    Institute of Scientific and Technical Information of China (English)

    朱长军; 秦元东; 杨宏; 王树峰; 龚旗煌

    2001-01-01

    Generation of third-order harmonics at 800 nm of femtosecond laser pulses is studied in neutral atmospheric air and in plasma of optical breakdown in air. Its efficiency is measured at different fundamental laser intensities. A maximum efficiency is observed at the intensity when optical breakdown in atmospheric air starts. The factors that exhibit the main effects on the harmonic generation, including self-focusing in a neutral air and self-focusing in plasma, are discussed.

  5. Observation and Modeling of Tsunami-Generated Gravity Waves in the Earth’s Upper Atmosphere

    Science.gov (United States)

    2015-10-08

    Observation and modeling of tsunami-generated gravity waves in the earth’s upper atmosphere 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...for public release; distribution is unlimited. Observation and modeling of tsunami-generated gravity waves in the earth’s upper atmosphere Sharon...viscosity), and reconstruct the GW field. We would then apply our models to several observed tsunamis, and calculate the GW field in the

  6. Basic characteristics of an atmospheric pressure rf generated plasma jet

    Institute of Scientific and Technical Information of China (English)

    Wang Shou-Guo; Li Hai-Jiang; Ye Tian-Chun; Zhao Ling-Li

    2004-01-01

    A plasma jet has been developed which operates using radio frequency (rf) power and produces a stable homogeneous discharge at atmospheric pressure. Its discharge characteristics, especially the dependence of stable discharge operating range on the feed gas, were studied, and the electric parameters such as RMS current, RMS voltage and reflected power were obtained with different gas flows. These studies indicate that there is an optimum range of operation of the plasma jet for a filling with a gas mixture of He and O2. Two "failure" modes of the discharge are identified.One is a filamentary arc when the input power is raised above a critical level, another is that the discharge disappears gradually as the addition of O2 approaches 3.2%. Possible explanations for the two failure modes have been given. The current and voltage waveform measurements show that there is a clear phase shift between normal and failure modes.In addition, Ⅰ-Ⅴ curves as a function of pure helium and for 1% addition of oxygen have been studied.

  7. Technetium-99m generator system

    Science.gov (United States)

    Mirzadeh, S.; Knapp, F.F. Jr.; Collins, E.D.

    1998-06-30

    A {sup 99}Mo/{sup 99m}Tc generator system includes a sorbent column loaded with a composition containing {sup 99}Mo. The sorbent column has an effluent end in fluid communication with an anion-exchange column for concentrating {sup 99m}Tc eluted from the sorbent column. A method of preparing a concentrated solution of {sup 99m}Tc includes the general steps of: (a) providing a sorbent column loaded with a composition containing {sup 99}Mo, the sorbent column having an effluent end in fluid communication with an anion-exchange column; (b) eluting the sorbent column with a salt solution to elute {sup 99m}Tc from the sorbent and to trap and concentrate the eluted {sup 99m}Tc on the ion-exchange column; and (c) eluting the concentrated {sup 99m}Tc from the ion-exchange column with a solution comprising a reductive complexing agent. 1 fig.

  8. Wind energy meteorology atmospheric physics for wind power generation

    CERN Document Server

    Emeis, Stefan

    2012-01-01

    This book is intended to give an introduction into the meteorological boundary conditions for power generation from the wind, onshore and offshore. It aims to provide reliable meteorological information for the planning and running of this important kind of renewable energy. This includes the derivation of wind laws and wind profile descriptions, especially those above the logarithmic surface layer. Winds over complex terrain and nocturnal low-level jets are considered as well. A special chapter is devoted to the efficiency of large wind parks and their wakes.

  9. A Project on Atmospheric Water Generator with the Concept of Peltier Effect

    Directory of Open Access Journals (Sweden)

    Aditya Nandy

    2014-06-01

    Full Text Available In many countries like India it is difficult to obtain water resources for irrigation or other purposes, especially in the arid regions. The problem of water scarcity is also observed in other places of the world due to lack of rainfall. However, in highly humid areas such as places close to the sea, water can be obtained by condensing the water vapour present in air. Here, the paper presents the method to develop a water condensation system based on thermoelectric cooler. The system consists of cooling elements, heat exchange unit and air circulation unit. A solar cell panel unit with a relevant high current output drives the cooling elements through a controlling circuit. Atmospheric Water Generator is a device that can convert atmospheric moisture directly into usable and even drinkable water. It is such a device which uses the principle of latent heat to convert molecules of water vapour into water droplets. It has been introduced a bit before, though it is not very common in India and some other countries. It has a great application standing on such age of technology where we all are running behind renewable sources. This paper also describes the experimental results and the system’s performance.

  10. IASI-NG: a new generation of infrared sounders for meteorology and atmospheric composition

    Science.gov (United States)

    Deschamps, A.; Bermudo, F.; Rousseau, S.; Bernard, F.; Pequignot, E.

    2016-12-01

    IASI-NG is the main payload of the future Metop-SG satellite of the Eumetsat EPS-SG program. This infrared atmospheric sounder generates radiance spectra at high resolution between 645cm-1 and 2760cm-1 and takes benefits from the IASI heritage. As for the first generation, the development of IASI-NG is under CNES responsibility. The first goal of the IASI-NG mission is to support Numerical Weather Prediction (NWP) by improving the estimation of humidity and temperature profiles, especially in the troposphere. To reach this goal, the spectral resolution will be two times better than for IASI first generation, and the radiometric noise will be divided by a factor of two. These performances will enable to support pollution monitoring, climate and atmospheric composition studies as well. CH4 and CO2 columns (but also O3, SO2, CO, NH3, HNO3 concentrations) are some of the products which will be derived from the IASI-NG measurements, in addition to NWP products (such as temperature and water vapor profiles, surface temperature and cloud information). This presentation describes in a first part the main characteristics of the instrument, which allow it to reach this level of performances. The interferometer, developed by Airbus Defense and Space, is based on the Mertz concept and allows to assess the self apodization by a field effect compensation (IASI-NG will be the first mission to implement Mertz Interferometer). In a second part, we present the main performances of the IASI-NG system, in terms of radiometric noise, spectral resolution and geolocation. We describe also the main algorithms which will be used in the ground segment to calibrate the data and correct the instrumental effects. Lastly, we give some information about the status of the project which is currently is the C/D phase and the major milestones in the IASI-NG agenda.

  11. Atmospheric fluidized bed combustion advanced concept system

    Energy Technology Data Exchange (ETDEWEB)

    1992-05-01

    DONLEE Technologies Inc. is developing with support of the US Department of Energy an advanced circulating fluidized bed technology known as the Vortex{trademark} Fluidized Bed Combustor (VFBC). The unique feature of the VFBC is the injection of a significant portion of the combustion air into the cyclone. Since as much as one-half of the total combustion air is injected into the cyclone, the cross-sectional area of the circulating fluidized bed is considerably smaller than typical circulating fluidized beds. The technology is being developed for two applications: Industrial-scale boilers ranging from 20,000 to 100,000 pounds per hour steam generating capacity; and two-stage combustion in which a substoichiometric Vortex Fluidized Bed Combustor (2VFBC) or precombustor is used to generate a combustible gas for use primarily in boiler retrofit applications. This Level II analysis of these two applications indicates that both have merit. An industrial-scale VFBC boiler (60,000 lb/hr of steam) is projected to be economically attractive with coal prices as high as $40 per ton and gas prices between $4 and $5 per thousand cubic feet. The payback time is between 3 and 4 years. The 2VFBC system was evaluated at three capacities of application: 20,000; 60,000 and 100,000 lb/hr of steam. The payback times for these three capacities are 4.5, 2.1 and 1.55 years, respectively. The 2VFBC has potential applications for retrofit of existing pulverized coal-fired boilers or as a new large (utility) boiler. Pressurized operation of the 2VFBC has considerable potential for combined cycle power generation applications. Experimental development of both applications is presented here to demonstrate the potential of these two technologies.

  12. Development of a Ground-Based Atmospheric Monitoring Network for the Global Mercury Observation System (GMOS

    Directory of Open Access Journals (Sweden)

    Sprovieri F.

    2013-04-01

    Full Text Available Consistent, high-quality measurements of atmospheric mercury (Hg are necessary in order to better understand Hg emissions, transport, and deposition on a global scale. Although the number of atmospheric Hg monitoring stations has increased in recent years, the available measurement database is limited and there are many regions of the world where measurements have not been extensively performed. Long-term atmospheric Hg monitoring and additional ground-based monitoring sites are needed in order to generate datasets that will offer new insight and information about the global scale trends of atmospheric Hg emissions and deposition. In the framework of the Global Mercury Observation System (GMOS project, a coordinated global observational network for atmospheric Hg is being established. The overall research strategy of GMOS is to develop a state-of-the-art observation system able to provide information on the concentration of Hg species in ambient air and precipitation on the global scale. This network is being developed by integrating previously established ground-based atmospheric Hg monitoring stations with newly established GMOS sites that are located both at high altitude and sea level locations, as well as in climatically diverse regions. Through the collection of consistent, high-quality atmospheric Hg measurement data, we seek to create a comprehensive assessment of atmospheric Hg concentrations and their dependence on meteorology, long-range atmospheric transport and atmospheric emissions.

  13. Entropy Generation in Regenerative Systems

    Science.gov (United States)

    Kittel, Peter

    1995-01-01

    Heat exchange to the oscillating flows in regenerative coolers generates entropy. These flows are characterized by oscillating mass flows and oscillating temperatures. Heat is transferred between the flow and heat exchangers and regenerators. In the former case, there is a steady temperature difference between the flow and the heat exchangers. In the latter case, there is no mean temperature difference. In this paper a mathematical model of the entropy generated is developed for both cases. Estimates of the entropy generated by this process are given for oscillating flows in heat exchangers and in regenerators. The practical significance of this entropy is also discussed.

  14. Trends in Wind Turbine Generator Systems

    DEFF Research Database (Denmark)

    Polinder, Henk; Ferreira, Jan Abraham; Jensen, Bogi Bech;

    2013-01-01

    This paper reviews the trends in wind turbine generator systems. After discussing some important requirements and basic relations, it describes the currently used systems: the constant speed system with squirrel-cage induction generator, and the three variable speed systems with doubly fed...

  15. Optimal Management and Design of Energy Systems under Atmospheric Uncertainty

    Science.gov (United States)

    Anitescu, M.; Constantinescu, E. M.; Zavala, V.

    2010-12-01

    The generation and distpatch of electricity while maintaining high reliability levels are two of the most daunting engineering problems of the modern era. This was demonstrated by the Northeast blackout of August 2003, which resulted in the loss of 6.2 gigawatts that served more than 50 million people and which resulted in economic losses on the order of $10 billion. In addition, there exist strong socioeconomic pressures to improve the efficiency of the grid. The most prominent solution to this problem is a substantial increase in the use of renewable energy such as wind and solar. In turn, its uncertain availability—which is due to the intrinsic weather variability—will increase the likelihood of disruptions. In this endeavors of current and next-generation power systems, forecasting atmospheric conditions with uncertainty can and will play a central role, at both the demand and the generation ends. User demands are strongly correlated to physical conditions such as temperature, humidity, and solar radiation. The reason is that the ambient temperature and solar radiation dictate the amount of air conditioning and lighting needed in residential and commercial buildings. But these potential benefits would come at the expense of increased variability in the dynamics of both production and demand, which would become even more dependent on weather state and its uncertainty. One of the important challenges for energy in our time is how to harness these benefits while “keeping the lights on”—ensuring that the demand is satisfied at all times and that no blackout occurs while all energy sources are optimally used. If we are to meet this challenge, accounting for uncertainty in the atmospheric conditions is essential, since this will allow minimizing the effects of false positives: committing too little baseline power in anticipation of demand that is underestimated or renewable energy levels that fail to materialize. In this work we describe a framework for the

  16. System for transporting an electron beam to the atmosphere for a gun with a plasma emitter

    Science.gov (United States)

    Kornilov, S. Yu.; Rempe, N. G.; Shidlovskiy, S. V.

    2016-06-01

    We report on the results of simulation of the gas flow in a gun with a plasma emitter and in the system for extracting the electron beam to the atmosphere, constructed on the basis of standard gasdynamic windows (GDWs). The design of the gun and GDWs is described. Calculations are performed for a pressure of about 10-3 Torr in the electron beam generation range. It is shown that the pressure drop to the atmospheric pressure in the system of electron beam extraction to the atmosphere can be ensured by two GDW stages evacuated by pumps with optimal performance.

  17. Solar system astrophysics planetary atmospheres and the outer solar system

    CERN Document Server

    Milone, Eugene F

    2008-01-01

    Solar System Astrophysics opens with coverage of the atmospheres, ionospheres and magnetospheres of the Earth, Venus and Mars and the magnetosphere of Mercury. The book then provides an introduction to meteorology and treating the physics and chemistry of these areas in considerable detail. What follows are the structure, composition, particle environments, satellites, and rings of Jupiter, Saturn, Uranus and Neptune, making abundant use of results from space probes. Solar System Astrophysics follows the history, orbits, structure, origin and demise of comets and the physics of meteors and provides a thorough treatment of meteorites, the asteroids and, in the outer solar system, the Kuiper Belt objects. The methods and results of extrasolar planet searches, the distinctions between stars, brown dwarfs, and planets, and the origins of planetary systems are examined. Historical introductions precede the development and discussion in most chapters. A series of challenges, useful as homework assignments or as foc...

  18. International arctic systems for observing the atmosphere

    DEFF Research Database (Denmark)

    Uttal, Taneil; Starkweather, Sandra; Drummond, James R.;

    2016-01-01

    IASOA activities and partnerships were initiated as a part of the 2007-2009 International Polar Year (IPY) and are expected to continue for many decades as a legacy program. The IASOA focus is on coordinating intensive measurements of the Arctic atmosphere collected in the U.S., Canada, Russia, N...

  19. Lithosphere-Atmosphere-Ionosphere Coupling System

    Science.gov (United States)

    Kachakhidze, Manana; Kachakhidze, Nino; Kaladze, Tamaz

    2014-06-01

    Modern ground-based and satellite methods of viewing enables to reveal those multiple anomalous geophysical phenomena which become evident in the period preceding earthquake and are directly connected with the process of its preparation. Lately special attention is attributed to the electromagnetic emissions fixed during large earthquake, and has already been successfully detected in Japan, America and Europe. Unfortunately there is no electromagnetic emissions detection network in Georgia, but the offered work, based on experimental data of foreign researchers and electrodynamics, presents an important theory about the electromagnetic emissions generation fixed in the earthquake preparation period. The extremely interesting methodology of possible prediction of earthquake is created and all anomalous geophysical phenomena are interpreted which take place some months, days or hours before earthquake in the lithosphereatmosphere-ionosphere coupling system. Most interesting is the idea of the authors to consider the electromagnetic radiation as the main earthquake precursor for the purpose of earthquake prediction, because of its informative nature and to consider all other anomalous geophysical phenomena which accompany the process of earthquake preparation as earthquake indicators. The offered work is the completely novel approach in earthquake problem searching with the view of earthquake prediction. It can form the base for creation of principally new trend in seismology, to be called conditionally "Earthquake Predictology".

  20. Ionic wind generation by a wire-cylinder-plate corona discharge in air at atmospheric pressure

    OpenAIRE

    Colas, Dorian,; Ferret, Antoine; Pai, David,; Lacoste, Deanna,; Laux, C.

    2010-01-01

    International audience; A wire-cylinder-plate electrode configuration is presented to generate ionic wind with a dc corona discharge in air at atmospheric pressure. The objective of the work is to maximize the power supplied to the flow in order to increase acceleration while avoiding breakdown. Thus, the proposed experimental setup addresses the problem of decoupling the mechanism of ion generation from that of ion acceleration. Using a wire-plate configuration as a reference, we have focuse...

  1. Gas-temperature-dependent generation of cryoplasma jet under atmospheric pressure

    Science.gov (United States)

    Noma, Yuri; Choi, Jai Hyuk; Tomai, Takaaki; Terashima, Kazuo

    2008-09-01

    Plasma with a gas temperature below room temperature is not yet fully understood although it is expected to be an attractive tool for applications to material processing. In the present work, gas-temperature-dependent generation of a cryoplasma jet was studied. So far, we have generated a helium cryoplasma jet (296-5K) under atmospheric pressure. At gas temperatures below 20K, the helium excimer, He2, was observed clearly from by optical emission spectroscopy.

  2. Energyless CO2 Absorption, Generation, and Fixation Using Atmospheric CO2.

    Science.gov (United States)

    Inagaki, Fuyuhiko; Okada, Yasuhiko; Matsumoto, Chiaki; Yamada, Masayuki; Nakazawa, Kenta; Mukai, Chisato

    2016-01-01

    From an economic and ecological perspective, the efficient utilization of atmospheric CO2 as a carbon resource should be a much more important goal than reducing CO2 emissions. However, no strategy to harvest CO2 using atmospheric CO2 at room temperature currently exists, which is presumably due to the extremely low concentration of CO2 in ambient air (approximately 400 ppm=0.04 vol%). We discovered that monoethanolamine (MEA) and its derivatives efficiently absorbed atmospheric CO2 without requiring an energy source. We also found that the absorbed CO2 could be easily liberated with acid. Furthermore, a novel CO2 generator enabled us to synthesize a high value-added material (i.e., 2-oxazolidinone derivatives based on the metal catalyzed CO2-fixation at room temperature) from atmospheric CO2.

  3. Spectral broadening of acoustic tones generated by unmanned aerial vehicles in a turbulent atmosphere

    DEFF Research Database (Denmark)

    Ostashev, Vladimir E.; Wilson, D. K.; Finn, Anthony

    2016-01-01

    The acoustic spectrum emitted by unmanned aerial vehicles (UAVs) and other aircraft can be distorted by propagation through atmospheric turbulence. Since most UAVs are propeller-based, they generate a series of acoustic tones and harmonics. In this paper, spectral broadening of these tones due...

  4. Differential cardiac effects in rats exposed to atmospheric smog generated from isoprene versus toluene

    Science.gov (United States)

    The results of this study demonstrate that atmospheric smog generated from both isoprene and toluene cause cardiac effects in rats. In addition, it appears that smog from toluene is more toxic in terms of cardiac arrhythmogenicity. Smog, which is a comple...

  5. Mutagenicity in Salmonella of a Simulated Urban-Smog Atmosphere Generated Using a Mobile Reaction Chamber

    Science.gov (United States)

    The EPA Mobile Reaction Chamber (MRC) is a 24-foot trailer containing a 14.3-m3 Teflon lined photochemical chamber used to generate simulated urban atmospheres. Photochemistry in the MRC is catalyzed by 120 fluorescent bulbs evenly mixed with black light bulbs and UV bulbs (300 &...

  6. Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems (ERASMUS)

    Energy Technology Data Exchange (ETDEWEB)

    Bland, Geoffrey [NASA Goddard Space Flight Center (GSFC), Greenbelt, MD (United States)

    2016-06-30

    The use of small unmanned aircraft systems (sUAS) with miniature sensor systems for atmospheric research is an important capability to develop. The Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems (ERASMUS) project, lead by Dr. Gijs de Boer of the Cooperative Institute for Research in Environmental Sciences (CIRES- a partnership of NOAA and CU-Boulder), is a significant milestone in realizing this new potential. This project has clearly demonstrated that the concept of sUAS utilization is valid, and miniature instrumentation can be used to further our understanding of the atmospheric boundary layer in the arctic.

  7. Integration of stochastic generation in power systems

    NARCIS (Netherlands)

    Papaefthymiou, G.

    2007-01-01

    Stochastic Generation is the electrical power production by the use of an uncontrollable prime energy mover, corresponding mainly to renewable energy sources. For the large-scale integration of stochastic generation in power systems, methods are necessary for the modeling of power generation

  8. Integration of stochastic generation in power systems

    NARCIS (Netherlands)

    Papaefthymiou, G.

    2007-01-01

    Stochastic Generation is the electrical power production by the use of an uncontrollable prime energy mover, corresponding mainly to renewable energy sources. For the large-scale integration of stochastic generation in power systems, methods are necessary for the modeling of power generation uncerta

  9. Integration of stochastic generation in power systems

    NARCIS (Netherlands)

    Papaefthymiou, G.

    2007-01-01

    Stochastic Generation is the electrical power production by the use of an uncontrollable prime energy mover, corresponding mainly to renewable energy sources. For the large-scale integration of stochastic generation in power systems, methods are necessary for the modeling of power generation uncerta

  10. Parameters of a supershort avalanche electron beam generated in atmospheric-pressure air

    Science.gov (United States)

    Tarasenko, V. F.

    2011-05-01

    Conditions under which the number of runaway electrons in atmospheric-pressure air reaches ˜5 × 1010 are determined. Recommendations for creating runaway electron accelerators are given. Methods for measuring the parameters of a supershort avalanche electron beam and X-ray pulses from gas-filled diodes, as well as the discharge current and gap voltage, are described. A technique for determining the instant of runaway electron generation with respect to the voltage pulse is proposed. It is shown that the reduction in the gap voltage and the decrease in the beam current coincide in time. The mechanism of intense electron beam generation in gas-filled diodes is analyzed. It is confirmed experimentally that, in optimal regimes, the number of electrons generated in atmospheric-pressure air with energies T > eU m , where U m is the maximum gap voltage, is relatively small.

  11. Energy distribution of runaway electrons generated by a nanosecond discharge in atmospheric-pressure air

    Science.gov (United States)

    Tarasenko, V. F.; Baksht, E. Kh.; Burachenko, A. G.; Kostyrya, I. D.; Lomaev, M. I.; Petin, V. K.; Rybka, D. V.; Shlyakhtun, S. V.

    2008-12-01

    The spectra of an ultrashort avalanche electron beam generated by a nanosecond discharge in atmospheric-pressure air were investigated. The temporal characteristics of the beam current pulses, gap voltage, and discharge current in a gas diode were measured with a time resolution of ˜0.1 ns. A simple technique was developed for recovering electron spectra from the curves of beam attenuation by aluminum foils. The effect of the cathode design, electrode gap length, and generator parameters on the electron spectra were studied using seven setups. It is shown that generation of electrons with anomalously high energies requires the use of cathodes with increased curvature radius.

  12. Experimental Study of a Thermoelectric Generation System

    DEFF Research Database (Denmark)

    Zhu, Junpeng; Gao, Junling; Chen, Min

    2011-01-01

    A flat wall-like thermoelectric generation system is developed for applications in exhaust heat of kilns. The design of the whole experimental setup is presented. The essential performance of the thermoelectric generation system is tested, including open-circuit voltage, output power, and system....... System-level simulation is carried out using a quasi-one-dimensional numerical model that enables direct comparison with experimental results. The results of both experiment and simulation will provide a foundation to improve and optimize complex thermoelectric generation systems....

  13. P systems generating iso-plcture languages

    Institute of Scientific and Technical Information of China (English)

    Subbaiah Annadurai; Thiyagarajan Kalyani; Vincent Rajkumar Dare; Durairaj Gnanaraj Thomas

    2008-01-01

    P systems generating rectangular arrays and hexagonal arrays have been studied in the literature,bringing together the two areas of theoretical computer science,namely membrane computing and picture languages.Recently,a new class of picture languages called the class of iso-picture languages generating interesting picture languages has been introduced.In this paper,we develop a class of tissue-like P systems with active membranes as a generative device for iso-picture languages.

  14. Maximal Heat Generation in Nanoscale Systems

    Institute of Scientific and Technical Information of China (English)

    ZHOU Li-Ling; LI Shu-Shen; ZENG Zhao-Yang

    2009-01-01

    We investigate the heat generation in a nanoscale system coupled to normal leads and find that it is maximal when the average occupation of the electrons in the nanoscale system is 0.5,no matter what mechanism induces the heat generation.

  15. Radiative transfer in atmosphere-sea ice-ocean system

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Z.; Stamnes, K.; Weeks, W.F. [Univ. of Alaska, Fairbanks, AK (United States); Tsay, S.C. [NASA Goddard Space Flight Center, Greenbelt, MD (United States)

    1996-04-01

    Radiative energy is critical in controlling the heat and mass balance of sea ice, which significantly affects the polar climate. In the polar oceans, light transmission through the atmosphere and sea ice is essential to the growth of plankton and algae and, consequently, to the microbial community both in the ice and in the ocean. Therefore, the study of radiative transfer in the polar atmosphere, sea ice, and ocean system is of particular importance. Lacking a properly coupled radiative transfer model for the atmosphere-sea ice-ocean system, a consistent study of the radiative transfer in the polar atmosphere, snow, sea ice, and ocean system has not been undertaken before. The radiative transfer processes in the atmosphere and in the ice and ocean have been treated separately. Because the radiation processes in the atmosphere, sea ice, and ocean depend on each other, this separate treatment is inconsistent. To study the radiative interaction between the atmosphere, clouds, snow, sea ice, and ocean, a radiative transfer model with consistent treatment of radiation in the coupled system is needed and is under development.

  16. Generation-IV Nuclear Energy Systems

    Science.gov (United States)

    McFarlane, Harold

    2008-05-01

    Nuclear power technology has evolved through roughly three generations of system designs: a first generation of prototypes and first-of-a-kind units implemented during the period 1950 to 1970; a second generation of industrial power plants built from 1970 to the turn of the century, most of which are still in operation today; and a third generation of evolutionary advanced reactors which began being built by the turn of the 20^th century, usually called Generation III or III+, which incorporate technical lessons learned through more than 12,000 reactor-years of operation. The Generation IV International Forum (GIF) is a cooperative international endeavor to develop advanced nuclear energy systems in response to the social, environmental and economic requirements of the 21^st century. Six Generation IV systems under development by GIF promise to enhance the future contribution and benefits of nuclear energy. All Generation IV systems aim at performance improvement, new applications of nuclear energy, and/or more sustainable approaches to the management of nuclear materials. High-temperature systems offer the possibility of efficient process heat applications and eventually hydrogen production. Enhanced sustainability is achieved primarily through adoption of a closed fuel cycle with reprocessing and recycling of plutonium, uranium and minor actinides using fast reactors. This approach provides significant reduction in waste generation and uranium resource requirements.

  17. Acoustic waves in the atmosphere and ground generated by volcanic activity

    Energy Technology Data Exchange (ETDEWEB)

    Ichihara, Mie; Lyons, John; Oikawa, Jun; Takeo, Minoru [Earthquake Research Institute, University of Tokyo, 1-1-1 Yayoi, Bunkyo-ku, Tokyo 113-0032 (Japan); Instituto Geofisico, Escuela Politecnica Nacional, Ladron de Guevara E11-253, Aptdo 2759, Quito (Ecuador); Earthquake Research Institute, University of Tokyo, 1-1-1 Yayoi, Bunkyo-ku, Tokyo 113-0032 (Japan)

    2012-09-04

    This paper reports an interesting sequence of harmonic tremor observed in the 2011 eruption of Shinmoe-dake volcano, southern Japan. The main eruptive activity started with ashcloud forming explosive eruptions, followed by lava effusion. Harmonic tremor was transmitted into the ground and observed as seismic waves at the last stage of the effusive eruption. The tremor observed at this stage had unclear and fluctuating harmonic modes. In the atmosphere, on the other hand, many impulsive acoustic waves indicating small surface explosions were observed. When the effusion stopped and the erupted lava began explosive degassing, harmonic tremor started to be transmitted also to the atmosphere and observed as acoustic waves. Then the harmonic modes became clearer and more stable. This sequence of harmonic tremor is interpreted as a process in which volcanic degassing generates an open connection between the volcanic conduit and the atmosphere. In order to test this hypothesis, a laboratory experiment was performed and the essential features were successfully reproduced.

  18. Temporal analysis of laser beam propagation in the atmosphere using computer-generated long phase screens.

    Science.gov (United States)

    Dios, Federico; Recolons, Jaume; Rodríguez, Alejandro; Batet, Oscar

    2008-02-04

    Temporal analysis of the irradiance at the detector plane is intended as the first step in the study of the mean fade time in a free optical communication system. In the present work this analysis has been performed for a Gaussian laser beam propagating in the atmospheric turbulence by means of computer simulation. To this end, we have adapted a previously known numerical method to the generation of long phase screens. The screens are displaced in a transverse direction as the wave is propagated, in order to simulate the wind effect. The amplitude of the temporal covariance and its power spectrum have been obtained at the optical axis, at the beam centroid and at a certain distance from these two points. Results have been worked out for weak, moderate and strong turbulence regimes and when possible they have been compared with theoretical models. These results show a significant contribution of beam wander to the temporal behaviour of the irradiance, even in the case of weak turbulence. We have also found that the spectral bandwidth of the covariance is hardly dependent on the Rytov variance.

  19. Generation of uniform atmospheric pressure argon glow plasma by dielectric barrier discharge

    Indian Academy of Sciences (India)

    Raju Bhai Tyata; Deepak Prasad Subedi; Rajendra Shrestha; Chiow San Wong

    2013-03-01

    In this paper, atmospheric pressure glow discharges (APGD) in argon generated in parallel plate dielectric barrier discharge system is investigated by means of electrical and optical measurements. Using a high voltage (0–20 kV) power supply operating at 10–30 kHz, homogeneous and steady APGD has been observed between the electrodes with gap spacing from 0.5 mm to 2 mm and with a dielectric barrier of thickness 2 mm while argon gas is fed at a controlled flow rate of 11/min. The electron temperature and electron density of the plasma are determined by means of optical emission spectroscopy. Our results show that the electron density of the discharge obtained is of the order of 1016 cm-3 while the electron temperature is estimated to be 0.65 eV. The important result is that electron density determined from the line intensity ratio method and stark broadening method are in very good agreement. The Lissajous figure is used to estimate the energy deposited to the glow discharge. It is found that the energy deposited to the discharge is in the range of 20 to 25 $\\$J with a discharge voltage of 1.85 kV. The energy deposited to the discharge is observed to be higher at smaller gas spacing. The glow discharge plasma is tested to be effective in reducing the hydrophobicity of polyethylene film significantly.

  20. Evaluation protocol for the WIND system atmospheric models

    Energy Technology Data Exchange (ETDEWEB)

    Fast, J.D.

    1991-12-31

    Atmospheric transport and diffusion models have been developed for real-time calculations of the location and concentration of toxic or radioactive materials during a accidental release at the Savannah River Site (SRS). These models are have been incorporated into an automated menu-driven computer based system called the WIND (Weather INformation and Display) system. In an effort to establish more formal quality assurance procedures for the WIND system atmospheric codes, a software evaluation protocol is being developed. An evaluation protocol is necessary to determine how well they may perform in emergency response (real-time) situations. The evaluation of high-impact software must be conducted in accordance with WSRC QA Manual, 1Q, QAP 20-1. This report will describe the method that will be used to evaluate the atmospheric models. The evaluation will determine the effectiveness of the atmospheric models in emergency response situations, which is not necessarily the same procedure used for research purposes. The format of the evaluation plan will provide guidance for the evaluation of atmospheric models that may be added to the WIND system in the future. The evaluation plan is designed to provide the user with information about the WIND system atmospheric models that is necessary for emergency response situations.

  1. Evaluation protocol for the WIND system atmospheric models

    Energy Technology Data Exchange (ETDEWEB)

    Fast, J.D.

    1991-01-01

    Atmospheric transport and diffusion models have been developed for real-time calculations of the location and concentration of toxic or radioactive materials during a accidental release at the Savannah River Site (SRS). These models are have been incorporated into an automated menu-driven computer based system called the WIND (Weather INformation and Display) system. In an effort to establish more formal quality assurance procedures for the WIND system atmospheric codes, a software evaluation protocol is being developed. An evaluation protocol is necessary to determine how well they may perform in emergency response (real-time) situations. The evaluation of high-impact software must be conducted in accordance with WSRC QA Manual, 1Q, QAP 20-1. This report will describe the method that will be used to evaluate the atmospheric models. The evaluation will determine the effectiveness of the atmospheric models in emergency response situations, which is not necessarily the same procedure used for research purposes. The format of the evaluation plan will provide guidance for the evaluation of atmospheric models that may be added to the WIND system in the future. The evaluation plan is designed to provide the user with information about the WIND system atmospheric models that is necessary for emergency response situations.

  2. Effects of cold atmospheric plasma generated in DI water on Cancer cells

    CERN Document Server

    Chen, Zhitong; Cheng, Xiaoqian; Gjika, Eda; Keidar, Michael

    2016-01-01

    Cold atmospheric plasma (CAP) has been shown to affect cells not only directly, but also by means of indirect treatment with previously prepared plasma stimulated solution. The objective of this study is to reveal the effects of plasma-stimulated media (PSM) on breast cancer cells (MDA-MB-231) and gastric cancer cells (NCl-N87). In our experiments, cold atmospheric plasma is generated in water using helium as carrier gas. The plasma generated in DI water during a 30-minute treatment had the strongest affect in inducing apoptosis in cultured human breast and gastric cancer cells. This result can be attributed to the presence of reactive oxygen species (ROS) and reactive nitrogen species (RNS) produced in water during treatment.

  3. Meteorological input for atmospheric dispersion models: an inter-comparison between new generation models

    Energy Technology Data Exchange (ETDEWEB)

    Busillo, C.; Calastrini, F.; Gualtieri, G. [Lab. for Meteorol. and Environ. Modell. (LaMMA/CNR-IBIMET), Florence (Italy); Carpentieri, M.; Corti, A. [Dept. of Energetics, Univ. of Florence (Italy); Canepa, E. [INFM, Dept. of Physics, Univ. of Genoa (Italy)

    2004-07-01

    The behaviour of atmospheric dispersion models is strongly influenced by meteorological input, especially as far as new generation models are concerned. More sophisticated meteorological pre-processors require more extended and more reliable data. This is true in particular when short-term simulations are performed, while in long-term modelling detailed data are less important. In Europe no meteorological standards exist about data, therefore testing and evaluating the results of new generation dispersion models is particularly important in order to obtain information on reliability of model predictions. (orig.)

  4. Stability for basic system of equations of atmospheric motion

    Institute of Scientific and Technical Information of China (English)

    SHI Wei-hui; XU Ming; WANG Yue-peng

    2007-01-01

    The topological characteristics for the basic system of equations of atmospheric motion were analyzed with the help of method provided by stratification theory. It was proved that in the local rectangular coordinate system the basic system of equations of atmospheric motion is stable in infinitely differentiable function class. In the sense of local solution, the necessary and sufficient conditions by which the typical problem for determining solution is well posed were also given. Such problems as something about "speculating future from past" in atmospheric dynamics and how to amend the conditions for determining solution as well as the choice of underlying surface when involving the practical application were further discussed. It is also pointed out that under the usual conditions, three motion equations and continuity equation in the basic system of equations determine entirely the property of this system of equations.

  5. The economic valuation on atmospheric improvement benefit by nuclear power generation

    Energy Technology Data Exchange (ETDEWEB)

    Kwak, S. J.; Yoo, S. H.; Han, S. Y.; Do, G. W.; Lee, J. S. [Korea Univ., Seoul (Korea)

    2000-12-01

    The major contents are as follows : To begin with, major air pollutants' emissions and emission reduction facilities in industrial sectors including a power generation were investigated and the future prospect was suggested. Environmental effects by attributes of air pollutions were summarized through a extensive literature survey. And the concept of benefit-cost based upon social costs and economic values of generation was established to estimate atmospheric improvement benefits by using a nuclear power. As a result of investigating many valuation methodologies that can estimate economic values of environmental improvement, we adopted MAUA(multi-attribute utility assessment) as a research method and estimated environmental costs by air pollutant and by power generating source. Also, we presented foreign case studies related to social costs in power generating sector and horizontally compared study's results home and abroad. Then, we set up four scenarios based on total generation that the 5th long-term power resources planning forecasted and calculated economic values of atmospheric improvement benefits among scenarios. Further, we suggested the results incorporating uncertainty of estimation parameters. Finally, we suggested a rational ground to move toward environment-friendly energy consumption and proposed a plan for the national energy policy against the green age in the 21th century. 147 refs., 45 figs., 103 tabs. (Author)

  6. Airborne experiment results for spaceborne atmospheric synchronous correction system

    Science.gov (United States)

    Cui, Wenyu; Yi, Weining; Du, Lili; Liu, Xiao

    2015-10-01

    The image quality of optical remote sensing satellite is affected by the atmosphere, thus the image needs to be corrected. Due to the spatial and temporal variability of atmospheric conditions, correction by using synchronous atmospheric parameters can effectively improve the remote sensing image quality. For this reason, a small light spaceborne instrument, the atmospheric synchronous correction device (airborne prototype), is developed by AIOFM of CAS(Anhui Institute of Optics and Fine Mechanics of Chinese Academy of Sciences). With this instrument, of which the detection mode is timing synchronization and spatial coverage, the atmospheric parameters consistent with the images to be corrected in time and space can be obtained, and then the correction is achieved by radiative transfer model. To verify the technical process and treatment effect of spaceborne atmospheric correction system, the first airborne experiment is designed and completed. The experiment is implemented by the "satellite-airborne-ground" synchronous measuring method. A high resolution(0.4 m) camera and the atmospheric correction device are equipped on the aircraft, which photograph the ground with the satellite observation over the top simultaneously. And aerosol optical depth (AOD) and columnar water vapor (CWV) in the imagery area are also acquired, which are used for the atmospheric correction for satellite and aerial images. Experimental results show that using the AOD and CWV of imagery area retrieved by the data obtained by the device to correct aviation and satellite images, can improve image definition and contrast by more than 30%, and increase MTF by more than 1 time, which means atmospheric correction for satellite images by using the data of spaceborne atmospheric synchronous correction device is accurate and effective.

  7. Automated Concurrent Blackboard System Generation in C++

    Science.gov (United States)

    Kaplan, J. A.; McManus, J. W.; Bynum, W. L.

    1999-01-01

    In his 1992 Ph.D. thesis, "Design and Analysis Techniques for Concurrent Blackboard Systems", John McManus defined several performance metrics for concurrent blackboard systems and developed a suite of tools for creating and analyzing such systems. These tools allow a user to analyze a concurrent blackboard system design and predict the performance of the system before any code is written. The design can be modified until simulated performance is satisfactory. Then, the code generator can be invoked to generate automatically all of the code required for the concurrent blackboard system except for the code implementing the functionality of each knowledge source. We have completed the port of the source code generator and a simulator for a concurrent blackboard system. The source code generator generates the necessary C++ source code to implement the concurrent blackboard system using Parallel Virtual Machine (PVM) running on a heterogeneous network of UNIX(trademark) workstations. The concurrent blackboard simulator uses the blackboard specification file to predict the performance of the concurrent blackboard design. The only part of the source code for the concurrent blackboard system that the user must supply is the code implementing the functionality of the knowledge sources.

  8. Analytical Models of Exoplanetary Atmospheres: Atmospheric Dynamics via the Shallow Water System

    CERN Document Server

    Heng, Kevin

    2014-01-01

    Within the context of exoplanetary atmospheres, we present a comprehensive linear analysis of forced, damped, magnetized shallow water systems, exploring the effects of dimensionality, geometry (Cartesian, pseudo-spherical and spherical), rotation, magnetic tension and hydrodynamic and magnetic sources of friction. Across a broad range of conditions, we find that the key governing equation for atmospheres and quantum harmonic oscillators are identical, even when forcing (stellar irradiation), sources of friction (molecular viscosity, Rayleigh drag and magnetic drag) and magnetic tension are included. The global atmospheric structure is largely controlled by a single, key parameter that involves the Rossby and Prandtl numbers. This near-universality breaks down when either molecular viscosity or magnetic drag varies significantly across latitude or a poloidal magnetic field is present, suggesting that these effects will introduce qualitative changes to the familiar chevron-shaped feature witnessed in simulatio...

  9. Development and Testing of a Sorbent-Based Atmosphere Revitalization System for the Crew Exploration Vehicle

    Science.gov (United States)

    Knox, James C.; Adams, Jeff; Kittredge, Ken

    2006-01-01

    The design of a vacuum-swing adsorption process to remove metabolic water, metabolic carbon dioxide, and metabolic and equipment generated trace contaminant gases from the Crew Exploration Vehicle (CEV) atmosphere is presented. For the CEV, the approach is taken that all metabolic water must be removed by the Sorbent-Based Atmosphere Revitalization System (SBAR), a technology approach that has not been used in previous spacecraft life support systems. Design and development of a prototype SBAR, a facility test stand, and subsequent testing of the SBAR is discussed.

  10. The Atmospheric Monitoring system of the JEM-EUSO telescope

    CERN Document Server

    Toscano, S; Frías, M D Rodríguez

    2014-01-01

    The JEM-EUSO observatory on board of the International Space Station (ISS) is a proposed pioneering space mission devoted to the investigation of Ultra High Energy Cosmic Rays (UHECRs). Looking downward at the earth's atmosphere with a 60$^\\circ$ Field of View (FoV), the JEM-EUSO telescope will detect the fluorescence and Cherenkov UV emission from UHECR induced Extensive Air Showers (EAS) penetrating in the atmosphere. The capability of reconstructing the properties of the primary cosmic ray depends on the accurate measurement of the atmospheric conditions in the region of EAS development. The Atmospheric Monitoring system of JEM-EUSO will continuously monitor the atmosphere at the location of the EAS candidates and between the EAS and the JEM-EUSO telescope. With an UV LIDAR and an Infrared (IR) Camera the system will monitor the cloud cover and retrieve the cloud top altitude with an accuracy of $\\sim$ 500 m and the optical depth profile of the atmosphere with an accuracy of $\\Delta\\tau \\leq$ 0.15 and a re...

  11. An Atmospheric Science Observing System Simulation Experiment (OSSE) Environment

    Science.gov (United States)

    Lee, Meemong; Weidner, Richard; Qu, Zheng; Bowman, Kevin; Eldering, Annmarie

    2010-01-01

    An atmospheric sounding mission starts with a wide range of concept designs involving measurement technologies, observing platforms, and observation scenarios. Observing system simulation experiment (OSSE) is a technical approach to evaluate the relative merits of mission and instrument concepts. At Jet Propulsion Laboratory (JPL), the OSSE team has developed an OSSE environment that allows atmospheric scientists to systematically explore a wide range of mission and instrument concepts and formulate a science traceability matrix with a quantitative science impact analysis. The OSSE environment virtually creates a multi-platform atmospheric sounding testbed (MAST) by integrating atmospheric phenomena models, forward modeling methods, and inverse modeling methods. The MAST performs OSSEs in four loosely coupled processes, observation scenario exploration, measurement quality exploration, measurement quality evaluation, and science impact analysis.

  12. A computer controlled mass spectrometer system for investigating the decomposition of non-metallic materials under atmospheric conditions

    Science.gov (United States)

    Thompson, J. M.

    1985-01-01

    A PDP 11/23 quadrupole mass spectrometer system was coupled to a nondiscriminating gas inlet system permitting gases at atmospheric pressure to be admitted into a high vacuum chamber containing the ion source of the mass spectrometer without separation of the gaseous components. The resolution of related software problems has resulted in a convenient computer-mass spectrometer system capable of generating masses, relative intensities and related data on the gaseous products resulting from the atmospheric thermal decomposition of nonmetallic materials.

  13. A computer controlled mass spectrometer system for investigating the decomposition of non-metallic materials under atmospheric conditions

    Science.gov (United States)

    Thompson, J. M.

    1985-01-01

    A PDP 11/23 quadrupole mass spectrometer system was coupled to a nondiscriminating gas inlet system permitting gases at atmospheric pressure to be admitted into a high vacuum chamber containing the ion source of the mass spectrometer without separation of the gaseous components. The resolution of related software problems has resulted in a convenient computer-mass spectrometer system capable of generating masses, relative intensities and related data on the gaseous products resulting from the atmospheric thermal decomposition of nonmetallic materials.

  14. Reactive species in non-equilibrium atmospheric-pressure plasmas: Generation, transport, and biological effects

    Science.gov (United States)

    Lu, X.; Naidis, G. V.; Laroussi, M.; Reuter, S.; Graves, D. B.; Ostrikov, K.

    2016-05-01

    Non-equilibrium atmospheric-pressure plasmas have recently become a topical area of research owing to their diverse applications in health care and medicine, environmental remediation and pollution control, materials processing, electrochemistry, nanotechnology and other fields. This review focuses on the reactive electrons and ionic, atomic, molecular, and radical species that are produced in these plasmas and then transported from the point of generation to the point of interaction with the material, medium, living cells or tissues being processed. The most important mechanisms of generation and transport of the key species in the plasmas of atmospheric-pressure plasma jets and other non-equilibrium atmospheric-pressure plasmas are introduced and examined from the viewpoint of their applications in plasma hygiene and medicine and other relevant fields. Sophisticated high-precision, time-resolved plasma diagnostics approaches and techniques are presented and their applications to monitor the reactive species and plasma dynamics in the plasma jets and other discharges, both in the gas phase and during the plasma interaction with liquid media, are critically reviewed. The large amount of experimental data is supported by the theoretical models of reactive species generation and transport in the plasmas, surrounding gaseous environments, and plasma interaction with liquid media. These models are presented and their limitations are discussed. Special attention is paid to biological effects of the plasma-generated reactive oxygen and nitrogen (and some other) species in basic biological processes such as cell metabolism, proliferation, survival, etc. as well as plasma applications in bacterial inactivation, wound healing, cancer treatment and some others. Challenges and opportunities for theoretical and experimental research are discussed and the authors' vision for the emerging convergence trends across several disciplines and application domains is presented to

  15. Reactive species in non-equilibrium atmospheric-pressure plasmas: Generation, transport, and biological effects

    Energy Technology Data Exchange (ETDEWEB)

    Lu, X., E-mail: luxinpei@hotmail.com [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); IFSA Collaborative Innovation Center, Shanghai Jiao Tong University, Shanghai 200240 (China); Naidis, G.V. [Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow 125412 (Russian Federation); Laroussi, M. [Plasma Engineering & Medicine Institute, Old Dominion University, Norfolk, VA 23529 (United States); Reuter, S. [Leibniz Institute for Plasma Science and Technology, Felix-Hausdorff-Strasse 2, 17489 Greifswald (Germany); Graves, D.B. [Department of Chemical and Biomolecular Engineering, University of California, Berkeley, CA 94720 (United States); Ostrikov, K. [Institute for Future Environments, Queensland University of Technology, Brisbane, QLD 4000 (Australia); School of Physics, Chemistry, and Mechanical Engineering, Queensland University of Technology, Brisbane, QLD 4000 (Australia); Commonwealth Scientific and Industrial Research Organization, P.O.Box 218, Lindfield, NSW 2070 (Australia); School of Physics, The University of Sydney, Sydney, NSW 2006 (Australia)

    2016-05-04

    Non-equilibrium atmospheric-pressure plasmas have recently become a topical area of research owing to their diverse applications in health care and medicine, environmental remediation and pollution control, materials processing, electrochemistry, nanotechnology and other fields. This review focuses on the reactive electrons and ionic, atomic, molecular, and radical species that are produced in these plasmas and then transported from the point of generation to the point of interaction with the material, medium, living cells or tissues being processed. The most important mechanisms of generation and transport of the key species in the plasmas of atmospheric-pressure plasma jets and other non-equilibrium atmospheric-pressure plasmas are introduced and examined from the viewpoint of their applications in plasma hygiene and medicine and other relevant fields. Sophisticated high-precision, time-resolved plasma diagnostics approaches and techniques are presented and their applications to monitor the reactive species and plasma dynamics in the plasma jets and other discharges, both in the gas phase and during the plasma interaction with liquid media, are critically reviewed. The large amount of experimental data is supported by the theoretical models of reactive species generation and transport in the plasmas, surrounding gaseous environments, and plasma interaction with liquid media. These models are presented and their limitations are discussed. Special attention is paid to biological effects of the plasma-generated reactive oxygen and nitrogen (and some other) species in basic biological processes such as cell metabolism, proliferation, survival, etc. as well as plasma applications in bacterial inactivation, wound healing, cancer treatment and some others. Challenges and opportunities for theoretical and experimental research are discussed and the authors’ vision for the emerging convergence trends across several disciplines and application domains is presented to

  16. An update of the generator of atmospheric muons from parametric formulas (MUPAGE)

    Science.gov (United States)

    Bazzotti, M.; Carminati, G.; Margiotta, A.; Spurio, M.

    2010-04-01

    We present a new version of the fast generator of atmospheric muons based on parametric formulas (MUPAGE). The parameterization of the deep sea muon flux relies on a primary Cosmic Ray flux and interaction model able to correctly reproduce the flux, the multiplicity distribution, the spatial distance between muons as measured by the underground MACRO experiment [1]. MUPAGE produces the event kinematics of the muon bundle on the surface of a user-defined cylinder, surrounding the virtual detector. The new version improves the possibility to select the total energy of the muons bundle, and the choice of a virtual cylinder of any dimensions. New version program summaryProgram title: MUPAGE Catalogue identifier: AEBT_v2_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEBT_v2_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 3421 No. of bytes in distributed program, including test data, etc.: 59 308 Distribution format: tar.gz Programming language: C++ Computer: The code has been developed and tested on Pentium M, 2.0 GHz; 2x Intel Xeon Quad Core, 2.33 GHz. Operating system: Scientific Linux 3.x; 4.x; 5.x; Slackware 12.0.0. RAM: 50 MB Supplementary material: The table mentioned in the "Summary of revisions" section, can be obtained here. Classification: 1.1, 11.3 External routines: ROOT ( http://root.cern.ch) Catalogue identifier of previous version: AEBT_v1_0 Journal reference of previous version: Comput. Phys. Comm. 179 (2008) 915 Does the new version supersede the previous version?: Yes Nature of problem: Fast simulation of atmospheric muon bundles for underwater/ice neutrino telescopes. Solution method: Atmospheric muon events are generated according to parametric formulas [2] giving the flux, the multiplicity, the radial distribution and the energy spectrum

  17. Nanostructured, complex hydride systems for hydrogen generation

    Directory of Open Access Journals (Sweden)

    Robert A. Varin

    2015-02-01

    Full Text Available Complex hydride systems for hydrogen (H2 generation for supplying fuel cells are being reviewed. In the first group, the hydride systems that are capable of generating H2 through a mechanical dehydrogenation phenomenon at the ambient temperature are discussed. There are few quite diverse systems in this group such as lithium alanate (LiAlH4 with the following additives: nanoiron (n-Fe, lithium amide (LiNH2 (a hydride/hydride system and manganese chloride MnCl2 (a hydride/halide system. Another hydride/hydride system consists of lithium amide (LiNH2 and magnesium hydride (MgH2, and finally, there is a LiBH4-FeCl2 (hydride/halide system. These hydride systems are capable of releasing from ~4 to 7 wt.% H2 at the ambient temperature during a reasonably short duration of ball milling. The second group encompasses systems that generate H2 at slightly elevated temperature (up to 100 °C. In this group lithium alanate (LiAlH4 ball milled with the nano-Fe and nano-TiN/TiC/ZrC additives is a prominent system that can relatively quickly generate up to 7 wt.% H2 at 100 °C. The other hydride is manganese borohydride (Mn(BH42 obtained by mechano-chemical activation synthesis (MCAS. In a ball milled (2LiBH4 + MnCl2 nanocomposite, Mn(BH42 co-existing with LiCl can desorb ~4.5 wt.% H2 at 100 °C within a reasonable duration of dehydrogenation. Practical application aspects of hydride systems for H2 generation/storage are also briefly discussed.

  18. Automatic Melody Generation System with Extraction Feature

    Science.gov (United States)

    Ida, Kenichi; Kozuki, Shinichi

    In this paper, we propose the melody generation system with the analysis result of an existing melody. In addition, we introduce the device that takes user's favor in the system. The melody generation is done by pitch's being arranged best on the given rhythm. The best standard is decided by using the feature element extracted from existing music by proposed method. Moreover, user's favor is reflected in the best standard by operating some of the feature element in users. And, GA optimizes the pitch array based on the standard, and achieves the system.

  19. Control system for bearingless motor-generator

    Science.gov (United States)

    Kascak, Peter E. (Inventor); Jansen, Ralph H. (Inventor); Dever, Timothy P. (Inventor)

    2010-01-01

    A control system for an electromagnetic rotary drive for bearingless motor-generators comprises a winding configuration comprising a plurality of individual pole pairs through which phase current flows, each phase current producing both a lateral force and a torque. A motor-generator comprises a stator, a rotor supported for movement relative to the stator, and a control system. The motor-generator comprises a winding configuration supported by the stator. The winding configuration comprises at least three pole pairs through which phase current flows resulting in three three-phase systems. Each phase system has a first rotor reference frame axis current that produces a levitating force with no average torque and a second rotor reference frame axis current that produces torque.

  20. Development of a new atmospheric pressure cold plasma jet generator and application in sterilization

    Institute of Scientific and Technical Information of China (English)

    Cheng Cheng; Liu Peng; Xu Lei; Zhang Li-Ye; Zhan Ru-Juan; Zhang Wen-Rui

    2006-01-01

    This paper reports that a new plasma generator at atmospheric pressure, which is composed of two homocentric cylindrical all-metal tubes, successfully generates a cold plasma jet. The inside tube electrode is connected to ground,the outside tube electrode is connected to a high-voltage power supply, and a dielectric layer is covered on the outside tube electrode. When the reactor is operated by low-frequency (6 kHz-20 kHz) AC supply in atmospheric pressure and argon is steadily fed as a discharge gas through inside tube electrode, a cold plasma jet is blown out into air and the plasma gas temperature is only 25-30 ℃. The electric character of the discharge is studied by using digital real-time oscilloscope (TDS 200-Series), and the discharge is capacitive. Preliminary results are presented on the decontamination of E.colis bacteria and Bacillus subtilis bacteria by this plasma jet, and an optical emission analysis of the plasma jet is presented in this paper. The ozone concentration generated by the plasma jet is 1.0 × 1016cm-3 which is acquired by using the ultraviolet absorption spectroscopy.

  1. Kite Generator System: Grid Integration and Validation

    OpenAIRE

    Ahmed, Mariam; Hably, Ahmad; Bacha, Seddik; Ovalle, Andres

    2014-01-01

    International audience; In this paper, the problem of grid integration of a kite generator system (KGS), is handled. The mechanical power generated by the kite's traction is translated into an electrical one via a permanent magnet synchronous machine. This power is then injected in the grid or used to supply an isolated load after passing a power electronics interface. Control schemes have been developed for grid connected or stand-alone operation and tested on a hardware-in-the-loop simulator.

  2. A new atmospheric aerosol phase equilibrium model (UHAERO: organic systems

    Directory of Open Access Journals (Sweden)

    N. R. Amundson

    2007-09-01

    Full Text Available In atmospheric aerosols, water and volatile inorganic and organic species are distributed between the gas and aerosol phases in accordance with thermodynamic equilibrium. Within an atmospheric particle, liquid and solid phases can exist at equilibrium. Models exist for computation of phase equilibria for inorganic/water mixtures typical of atmospheric aerosols; when organic species are present, the phase equilibrium problem is complicated by organic/water interactions as well as the potentially large number of organic species. We present here an extension of the UHAERO inorganic thermodynamic model (Amundson et al., 2006c to organic/water systems. Phase diagrams for a number of model organic/water systems characteristic of both primary and secondary organic aerosols are computed. Also calculated are inorganic/organic/water phase diagrams that show the effect of organics on inorganic deliquescence behavior. The effect of the choice of activity coefficient model for organics on the computed phase equilibria is explored.

  3. A new atmospheric aerosol phase equilibrium model (UHAERO: organic systems

    Directory of Open Access Journals (Sweden)

    N. R. Amundson

    2007-06-01

    Full Text Available In atmospheric aerosols, water and volatile inorganic and organic species are distributed between the gas and aerosol phases in accordance with thermodynamic equilibrium. Within an atmospheric particle, liquid and solid phases can exist at equilibrium. Models exist for computation of phase equilibria for inorganic/water mixtures typical of atmospheric aerosols; when organic species are present, the phase equilibrium problem is complicated by organic/water interactions as well as the potentially large number of organic species. We present here an extension of the UHAERO inorganic thermodynamic model (Amundson et al., 2006c to organic/water systems. Phase diagrams for a number of model organic/water systems characteristic of both primary and secondary organic aerosols are computed. Also calculated are inorganic/organic/water phase diagrams that show the effect of organics on inorganic deliquescence behavior. The effect of the choice of activity coefficient model for organics on the computed phase equilibria is explored.

  4. Tube bundle system: for monitoring of coal mine atmosphere.

    Science.gov (United States)

    Zipf, R Karl; Marchewka, W; Mohamed, K; Addis, J; Karnack, F

    2013-05-01

    A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fire or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. Most longwall coal mines in Australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflow monitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

  5. Mars Entry Atmospheric Data System Trajectory Reconstruction Algorithms and Flight Results

    Science.gov (United States)

    Karlgaard, Christopher D.; Kutty, Prasad; Schoenenberger, Mark; Shidner, Jeremy; Munk, Michelle

    2013-01-01

    The Mars Entry Atmospheric Data System is a part of the Mars Science Laboratory, Entry, Descent, and Landing Instrumentation project. These sensors are a system of seven pressure transducers linked to ports on the entry vehicle forebody to record the pressure distribution during atmospheric entry. These measured surface pressures are used to generate estimates of atmospheric quantities based on modeled surface pressure distributions. Specifically, angle of attack, angle of sideslip, dynamic pressure, Mach number, and freestream atmospheric properties are reconstructed from the measured pressures. Such data allows for the aerodynamics to become decoupled from the assumed atmospheric properties, allowing for enhanced trajectory reconstruction and performance analysis as well as an aerodynamic reconstruction, which has not been possible in past Mars entry reconstructions. This paper provides details of the data processing algorithms that are utilized for this purpose. The data processing algorithms include two approaches that have commonly been utilized in past planetary entry trajectory reconstruction, and a new approach for this application that makes use of the pressure measurements. The paper describes assessments of data quality and preprocessing, and results of the flight data reduction from atmospheric entry, which occurred on August 5th, 2012.

  6. Einstein's Tea Leaves and Pressure Systems in the Atmosphere

    Science.gov (United States)

    Tandon, Amit; Marshall, John

    2010-01-01

    Tea leaves gather in the center of the cup when the tea is stirred. In 1926 Einstein explained the phenomenon in terms of a secondary, rim-to-center circulation caused by the fluid rubbing against the bottom of the cup. This explanation can be connected to air movement in atmospheric pressure systems to explore, for example, why low-pressure…

  7. On reliability optimization for power generation systems

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The reliability level of a power generation system is an important problem which is concerned by both electricity producers and electricity consumers. Why? It is known that the high reliability level may result in additional utility cost, and the low reliability level may result in additional consumer's cost, so the optimum reliability level should be determined such that the total cost can reach its minimum. Four optimization models for power generation system reliability are constructed, and the proven efficient solutions for these models are also given.

  8. Synchronous generator wind energy conversion control system

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, A.L.R. [Wind Energy Group, Recife (Brazil); Lima, A.M.N.; Jacobina, C.B.; Simoes, F.J. [DEE, Campina Grande (Brazil)

    1996-12-31

    This paper presents the performance evaluation and the design of the control system of a WECS (Wind Energy Conversion System) that employs a synchronous generator based on its digital simulation. The WECS discussed in this paper is connected to the utility grid through two Pulse Width Modulated (PWM) power converters. The structure of the proposed WECS enables us to achieve high performance energy conversion by: (i) maximizing the wind energy capture and (ii) minimizing the reactive power flowing between the grid and the synchronous generator. 8 refs., 19 figs.

  9. Photochemical hazes in planetary atmospheres: solar system bodies and beyond

    Science.gov (United States)

    Imanaka, Hiroshi; Cruikshank, Dale P.; McKay, Christopher P.

    2015-11-01

    Recent transit observations of exoplanets have demonstrated the possibility of a wide prevalence of haze/cloud layers at high altitudes. Hydrocarbon photochemical haze could be the candidate for such haze particles on warm sub-Neptunes, but the lack of evidence for methane poses a puzzle for such hydrocarbon photochemical haze. The CH4/CO ratios in planetary atmospheres vary substantially from their temperature and dynamics. An understanding of haze formation rates and plausible optical properties in a wide diversity of planetary atmospheres is required to interpret the current and future observations.Here, we focus on how atmospheric compositions, specifically CH4/CO ratios, affect the haze production rates and their optical properties. We have conducted a series of cold plasma experiments to constrain the haze mass production rates from gas mixtures of various CH4/CO ratios diluted either in H2 or N2 atmosphere. The mass production rates in the N2-CH4-CO system are much greater than those in the H2-CH4-CO system. They are rather insensitive to the CH4/CO ratios larger than at 0.3. Significant formation of solid material is observed both in H2-CO and N2-CO systems without CH4 in the initial gas mixtures. The complex refractive indices were derived for haze samples from N2-CH4, H2-CH4, and H2-CO gas mixtures. These are the model atmospheres for Titan, Saturn, and exoplanets, respectively. The imaginary part of the complex refractive indices in the UV-Vis region are distinct among these samples, which can be utilized for modeling these planetary atmospheres.

  10. The generation and damping of propagating MHD kink waves in the solar atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Morton, R. J. [Mathematics and Information Sciences, Northumbria University, Newcastle Upon Tyne NE1 8ST (United Kingdom); Verth, G.; Erdélyi, R. [Solar Physics and Space Plasma Research Centre (SP2RC), The University of Sheffield, Hicks Building, Hounsfield Road, Sheffield S3 7RH (United Kingdom); Hillier, A., E-mail: richard.morton@northumbria.ac.uk, E-mail: g.verth@sheffield.ac.uk, E-mail: robertus@sheffield.ac.uk [Kwasan and Hida Observatories, Kyoto University, 17 Ohmine-cho Kita Kazan, Yamashina-ku, Kyoto City, Kyoto 607-8471 (Japan)

    2014-03-20

    The source of the non-thermal energy required for the heating of the upper solar atmosphere to temperatures in excess of a million degrees and the acceleration of the solar wind to hundreds of kilometers per second is still unclear. One such mechanism for providing the required energy flux is incompressible torsional Alfvén and kink magnetohydrodynamic (MHD) waves, which are magnetically dominated waves supported by the Sun's pervasive and complex magnetic field. In particular, propagating MHD kink waves have recently been observed to be ubiquitous throughout the solar atmosphere, but, until now, critical details of the transport of the kink wave energy throughout the Sun's atmosphere were lacking. Here, the ubiquity of the waves is exploited for statistical studies in the highly dynamic solar chromosphere. This large-scale investigation allows for the determination of the chromospheric kink wave velocity power spectra, a missing link necessary for determining the energy transport between the photosphere and corona. Crucially, the power spectra contain evidence for horizontal photospheric motions being an important mechanism for kink wave generation in the quiescent Sun. In addition, a comparison with measured coronal power spectra is provided for the first time, revealing frequency-dependent transmission profiles, suggesting that there is enhanced damping of kink waves in the lower corona.

  11. Treatment of gastric cancer cells with non-thermal atmospheric plasma generated in water

    CERN Document Server

    Chen, Zhitong; Cheng, Xiaoqian; Gjika, Eda; Keidar, Michael

    2016-01-01

    Non-thermal atmospheric plasma (NTAP) can be applied to living tissues and cells as a novel technology for cancer therapy. Even though studies report on the successful use of NTAP to directly irradiate cancer cells, this technology can cause cell death only in the upper 3-5 cell layers. We report on a NTAP argon solution generated in DI water for treating human gastric cancer cells (NCl-N87). Our findings showed that the plasma generated in DI water during a 30-minute treatment had the strongest affect in inducing apoptosis in cultured human gastric cancer cells. This result can be attributed to presence of reactive oxygen species (ROS) and reactive nitrogen species (RNS) produced in water during treatment. Furthermore, the data showed that elevated levels of RNS may play an even more significant role than ROS in the rate of apoptosis in gastric cancer cells.

  12. Turbulent jet flow generated downstream of a low temperature dielectric barrier atmospheric pressure plasma device

    Science.gov (United States)

    Whalley, Richard D.; Walsh, James L.

    2016-08-01

    Flowing low temperature atmospheric pressure plasma devices have been used in many technological applications ranging from energy efficient combustion through to wound healing and cancer therapy. The generation of the plasma causes a sudden onset of turbulence in the inhomogeneous axisymmetric jet flow downstream of the plasma plume. The mean turbulent velocity fields are shown to be self-similar and independent of the applied voltage used to generate the plasma. It is proposed that the production of turbulence is related to a combination of the small-amplitude plasma induced body forces and gas heating causing perturbations in the unstable shear layers at the jet exit which grow as they move downstream, creating turbulence.

  13. Vortex beam generation based on a fiber array combining and propagation through a turbulent atmosphere

    Science.gov (United States)

    Aksenov, V. P.; Dudorov, V. V.; Kolosov, V. V.

    2016-09-01

    We suggest a technique for generation of optical vortex beams with a variable orbital angular momentum based on a fiber laser array. The technique uses the phase control of each single subbeam. Requirements for the number of subbeams and the spatial arrangement for the vortex beam generation are determined. The propagation dynamics of a vortex beam synthesized is compared with that of a continuous Laguerre-Gaussian beam in free space and in a turbulent atmosphere. Spectral properties of a beam synthesized, which is represented as a superposition of different azimuth modes, are determined during its free-space propagation. It is shown that energy and statistical parameters coincide for synthesized and continuous vortex beams when propagating through a turbulent medium. Probability density functions of the beam intensity fluctuations are well approximated to a gamma distribution in the cases where the scintillation index is lower than unity independently of the beam type and observation point position relative to the propagation axis.

  14. Turbulent jet flow generated downstream of a low temperature dielectric barrier atmospheric pressure plasma device.

    Science.gov (United States)

    Whalley, Richard D; Walsh, James L

    2016-08-26

    Flowing low temperature atmospheric pressure plasma devices have been used in many technological applications ranging from energy efficient combustion through to wound healing and cancer therapy. The generation of the plasma causes a sudden onset of turbulence in the inhomogeneous axisymmetric jet flow downstream of the plasma plume. The mean turbulent velocity fields are shown to be self-similar and independent of the applied voltage used to generate the plasma. It is proposed that the production of turbulence is related to a combination of the small-amplitude plasma induced body forces and gas heating causing perturbations in the unstable shear layers at the jet exit which grow as they move downstream, creating turbulence.

  15. 2010 Atmospheric System Research (ASR) Science Team Meeting Summary

    Energy Technology Data Exchange (ETDEWEB)

    Dupont, DL

    2011-05-04

    This document contains the summaries of papers presented in poster format at the March 2010 Atmospheric System Research Science Team Meeting held in Bethesda, Maryland. More than 260 posters were presented during the Science Team Meeting. Posters were sorted into the following subject areas: aerosol-cloud-radiation interactions, aerosol properties, atmospheric state and surface, cloud properties, field campaigns, infrastructure and outreach, instruments, modeling, and radiation. To put these posters in context, the status of ASR at the time of the meeting is provided here.

  16. Framework of Distributed Coupled Atmosphere-Ocean-Wave Modeling System

    Institute of Scientific and Technical Information of China (English)

    WEN Yuanqiao; HUANG Liwen; DENG Jian; ZHANG Jinfeng; WANG Sisi; WANG Lijun

    2006-01-01

    In order to research the interactions between the atmosphere and ocean as well as their important role in the intensive weather systems of coastal areas, and to improve the forecasting ability of the hazardous weather processes of coastal areas, a coupled atmosphere-ocean-wave modeling system has been developed.The agent-based environment framework for linking models allows flexible and dynamic information exchange between models. For the purpose of flexibility, portability and scalability, the framework of the whole system takes a multi-layer architecture that includes a user interface layer, computational layer and service-enabling layer. The numerical experiment presented in this paper demonstrates the performance of the distributed coupled modeling system.

  17. Transport of water in a transient impact-generated lunar atmosphere

    Science.gov (United States)

    Prem, P.; Artemieva, N. A.; Goldstein, D. B.; Varghese, P. L.; Trafton, L. M.

    2015-07-01

    In recent decades, several missions have detected signs of water and other volatiles in cold, permanently shadowed craters near the lunar poles. Observations suggest that some of these volatiles could have been delivered by comet impacts and therefore, understanding the impact delivery mechanism becomes key to explaining the origin and distribution of lunar water. During impact, the constituent ices of a comet nucleus vaporize; a significant part of this vapor remains gravitationally bound to the Moon, transforming the tenuous, collisionless lunar exosphere into a collisionally thick, transient atmosphere. Here, we use numerical simulations to investigate the physical processes governing volatile transport in the transient atmosphere generated after a comet impact, with a focus on how these processes influence the accumulation of water in polar cold traps. It is observed that the transient atmosphere maintains a certain characteristic structure for at least several Earth days after impact, during which time volatile transport occurs primarily through low-altitude winds that sweep over the lunar day-side. Meanwhile, reconvergence of vapor antipodal to the point of impact results in preferential redistribution of water in the vicinity of the antipode. Due to the quantity of vapor that remains gravitationally bound, the atmosphere is sufficiently dense that lower layers are shielded from photodestruction, prolonging the lifetime of water molecules and allowing greater amounts of water to reach cold traps. Short-term ice deposition patterns are markedly non-uniform and the variations that arise in simulated volatile abundance between different cold traps could potentially explain variations that have been observed through remote sensing.

  18. Study of an Atmospheric Pressure Plasma Jet of Argon Generated by Column Dielectric Barrier Discharge

    Science.gov (United States)

    Nur, M.; Kinandana, A. W.; Winarto, P.; Muhlisin, Z.; Nasrudin

    2016-11-01

    An atmospheric of argon plasma jet was generated by using column dielectric barrier discharge has been investigated. In this study, argon gas was passed through the capillary column by regulating the flow rate of gas. This atmospheric pressure plasma jet (APPJ) was generated by a sinusoidal AC high voltage in the range of 0.4 kV to 10 kV and at frequencies of 15 kHz and 26 kHz. APPJ has been produced with flow rate of argon gas from 1 litter/min - 10 litters/min. The electric current has been taken with variation of voltage and each interval argon gas flow rate of 1 litter/min. The results show that electric current increase linearly and then it trends to saturation condition by the increasing of applied voltage. We found also that the length of the plasma jet increase by augmenting of applied voltage both for frequencies of 15 kHz and 26 kHz. Furthermore, our results show that length of plasma jet optimum for flow rate of argon gas of 2 litters/minute. In addition, we obtained that the larger applied voltage, the greater the temperature of the plasma jet.

  19. Hybrid compensation arrangement in dispersed generation systems

    DEFF Research Database (Denmark)

    Chen, Zhe; Blaabjerg, Frede; Pedersen, John Kim

    2005-01-01

    This paper presents a hybrid compensation system consisting of an active filter and distributed passive filters. In the system, each individual passive filter is connected to a distortion source and designed to eliminate main harmonics and supply reactive power for the distortion source, while...... are performed for a power system including the dispersed generation units connected into the system through power electronic converters and diode rectifier loads, which produce the distorted waveforms. The simulation results have demonstrated that good compensation effects can be achieved by using the combined...

  20. Lifting Entry & Atmospheric Flight (LEAF) Applications at Solar System Bodies.

    Science.gov (United States)

    Lee, G.; Sen, B.; Polidan, R. S.

    2015-12-01

    Introduction: Northrop Grumman and L'Garde have continued the development of a hypersonic entry, maneuverable platform capable of performing long-duration (months to a year) in situ and remote measurements at any solar system body that possesses an atmosphere. The Lifting Entry & Atmospheric Flight (LEAF) family of vehicles achieve this capability by using a semi-buoyant, ultra-low ballistic coefficient vehicle whose lifting entry allows it to enter the atmosphere without an aeroshell. In this presentation, we discuss the application of the LEAF system at various solar system bodies: Venus, Titan, Mars, and Earth. We present the key differences in platform design as well as operational differences required by the various target environments. The Venus implementation includes propulsive capability to reach higher altitudes during the day and achieves full buoyancy in the "habitable layers" of Venus' atmosphere at night. Titan also offers an attractive operating environment, allowing LEAF designs that can target low, medium, or high altitude operations, also with propulsive capabilities to roam within each altitude regime. The Mars version is a glider that descends gradually, allowing targeted delivery of payloads to the surface. Finally, an Earth version could remain in orbit in a stowed state until activated, allowing rapid response type deployments to any region of the globe.

  1. Tactical Atmospheric Modeling System-Real Time (TAMS-RT)

    Science.gov (United States)

    2016-06-07

    subject to a penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. 1. REPORT DATE 30...mesoscale model analysis and forecast fields as inputs. OBJECTIVES Support the NRL Tactical Atmospheric Modeling System-Real Time (TAMS-RT) installed in...installation at NCMOC, the Space and Naval Warfare Systems Command (SPAWAR), who has configuration management oversight for TEDS, has changed the TEDS

  2. Generating units performances: power system requirements

    Energy Technology Data Exchange (ETDEWEB)

    Fourment, C.; Girard, N.; Lefebvre, H.

    1994-08-01

    The part of generating units within the power system is more than providing power and energy. Their performance are not only measured by their energy efficiency and availability. Namely, there is a strong interaction between the generating units and the power system. The units are essential components of the system: for a given load profile the frequency variation follows directly from the behaviour of the units and their ability to adapt their power output. In the same way, the voltage at the units terminals are the key points to which the voltage profile at each node of the network is linked through the active and especially the reactive power flows. Therefore, the customer will experience the frequency and voltage variations induced by the units behaviour. Moreover, in case of adverse conditions, if the units do not operate as well as expected or trip, a portion of the system, may be the whole system, may collapse. The limitation of the performance of a unit has two kinds of consequences. Firstly, it may result in an increased amount of not supplied energy or loss of load probability: for example if the primary reserve is not sufficient, a generator tripping may lead to an abnormal frequency deviation, and load may have to be shed to restore the balance. Secondly, the limitation of a unit performance results in an economic over-cost for the system: for instance, if not enough `cheap` units are able to load-following, other units with higher operating costs have to be started up. We would like to stress the interest for the operators and design teams of the units on the one hand, and the operators and design teams of the system on the other hand, of dialog and information exchange, in operation but also at the conception stage, in order to find a satisfactory compromise between the system requirements and the consequences for the generating units. (authors). 11 refs., 4 figs.

  3. An Integrated Global Atmospheric Composition Observing System: Progress and Impediments

    Science.gov (United States)

    Keating, T. J.

    2016-12-01

    In 2003-2005, a vision of an integrated global observing system for atmospheric composition and air quality emerged through several international forums (IGACO, 2004; GEO, 2005). In the decade since, the potential benefits of such a system for improving our understanding and mitigation of health and climate impacts of air pollution have become clearer and the needs more urgent. Some progress has been made towards the goal: technology has developed, capabilities have been demonstrated, and lessons have been learned. In Europe, the Copernicus Atmospheric Monitoring Service has blazed a trail for other regions to follow. Powerful new components of the emerging global system (e.g. a constellation of geostationary instruments) are expected to come on-line in the near term. But there are important gaps in the emerging system that are likely to keep us from achieving for some time the full benefits that were envisioned more than a decade ago. This presentation will explore the components and benefits of an integrated global observing system for atmospheric composition and air quality, some of the gaps and obstacles that exist in our current capabilities and institutions, and efforts that may be needed to achieve the envisioned system.

  4. Generation of Electron Suprathermal Tails in the Upper Solar Atmosphere: Implications for Coronal Heating

    Science.gov (United States)

    Vinas, Adolfo F.; Wong, Hung K.; Klimas, Alexander J.

    1999-01-01

    We present a mechanism for the generation of non-Maxwellian electron distribution function in the upper regions of the solar atmosphere in the presence of collisional damping. It is suggested that finite amplitude, low frequency, obliquely propagating electromagnetic waves can carry a substantial electric field component parallel to the mean magnetic field that can be significantly larger than the Dreicer electric field. This long wavelength electric fluctuation is capable of generating high frequency electron plasma oscillations and low frequency ion acoustic-like waves. The analysis has been performed using 1-1/2D Vlasov and PIC numerical simulations in which both electrons and ions are treated kinetically and self consistently. The simulation results indicate that high frequency electron plasma oscillations and low frequency ion acoustic-like waves are generated. The high frequency electron plasma oscillation drives electron plasma turbulence, which subsequently is damped out by the background electrons. The turbulence damping results in electron acceleration and the generation of non-Maxwellian suprathermal tails on time scales short compared to collisional damping. Bulk heating also occurs if the fluctuating parallel electric field is strong enough. This study suggests that finite amplitude, low frequency, obliquely propagating, electromagnetic waves can play a significant role in the acceleration and heating of the solar corona electrons and in the coupling of medium and small-scale phenomena.

  5. Hybrid Atmospheric, Land, and Oceanic (HALO) Measurements for Next-Generation Remote Sensing Applications

    Science.gov (United States)

    Bernhard, G. H.; Morrow, J. H.; Booth, C. R.; Hooker, S.

    2011-12-01

    irradiance; Langley plots; aerosol optical depth; aerosol size distributions; single scattering albedo; total ozone; cloud optical depth, and sky radiance distributions. Novel methods for shadowband operation, spectrograph stray light correction, and retrieval of high-resolution spectra from the filter-channel measurements are also presented. Measurements of global spectral irradiance agree with similar measurements of a high-resolution scanning spectroradiometer to within ±1.5%. Measurements of total ozone agree with observations of an Ozone Monitoring Instrument (OMI) to within ±3%. Data processing software is currently being advanced to include additional data products such as aerosol phase function, precipitable water vapor, polarimetry, and water-leaving radiance. Future NASA missions couple remote sensing observations with next-generation satellites. The oceanographic community has embraced the synergism of such a mission, coupling the use of novel, near surface (<2 m) optical profilers and new airborne microradiometer systems such as those deployed during NASA's Coastal and Ocean Airborne Science Testbed (COAST) mission. Dynamic positioning of airborne radiometers for satellite mission cal/val and sun photometry is a provocative next step.

  6. Physical features of atmospheric pressure microdischarge system with vortex gas flows

    Directory of Open Access Journals (Sweden)

    Prysiazhnevych Iryna

    2014-11-01

    Full Text Available The parameters for microdischarges of plasma medicine in air and argon vortex flows at atmospheric pressure for different shapes of electrodes (outlet nozzle and axis electrode diameters ratio set have been investigated. The current-voltage characteristics of the designed systems have been analyzed, the parameters of the generated jets plasma have been investigated by means of the optical emission spectroscopy, and the form of plasma jets has been studied by using video camera.

  7. Entropy budget of the earth,atmosphere and ocean system

    Institute of Scientific and Technical Information of China (English)

    GAN Zijun; YAN Youfangand; QI Yiquan

    2004-01-01

    The energy budget in the system of the earth, atmosphere and ocean conforms to the first law of thermodynamics, namely the law of conservation of energy, and it is balanced when the system is in a steady-state condition. However, the entropy budget following the second law of thermodynamics is unbalanced. In this paper, we deduce the expressions of entropy flux and re-estimate the earth, atmosphere and ocean annual mean entropy budget with the updated climatologically global mean energy budget and the climatologically air-sea flux data. The calculated results show that the earth system obtains a net influx of negative entropy (-1179.3 mWm-2K-1) from its surroundings, and the atmosphere and the ocean systems obtain a net input of negative entropy at about -537.4 mWm-2K-1 and -555.6 mWm-2K-1, respectively. Calculations of the entropy budget can provide some guidance for further understanding the spatial-temporal change of the local entropy flux, and the entropy production resulting from all kinds of irreversible processes inside these systems.

  8. Self-consistent modeling of induced magnetic field in Titan's atmosphere accounting for the generation of Schumann resonance

    Science.gov (United States)

    Béghin, Christian

    2015-02-01

    This model is worked out in the frame of physical mechanisms proposed in previous studies accounting for the generation and the observation of an atypical Schumann Resonance (SR) during the descent of the Huygens Probe in the Titan's atmosphere on 14 January 2005. While Titan is staying inside the subsonic co-rotating magnetosphere of Saturn, a secondary magnetic field carrying an Extremely Low Frequency (ELF) modulation is shown to be generated through ion-acoustic instabilities of the Pedersen current sheets induced at the interface region between the impacting magnetospheric plasma and Titan's ionosphere. The stronger induced magnetic field components are focused within field-aligned arcs-like structures hanging down the current sheets, with minimum amplitude of about 0.3 nT throughout the ramside hemisphere from the ionopause down to the Moon surface, including the icy crust and its interface with a conductive water ocean. The deep penetration of the modulated magnetic field in the atmosphere is thought to be allowed thanks to the force balance between the average temporal variations of thermal and magnetic pressures within the field-aligned arcs. However, there is a first cause of diffusion of the ELF magnetic components, probably due to feeding one, or eventually several SR eigenmodes. A second leakage source is ascribed to a system of eddy-Foucault currents assumed to be induced through the buried water ocean. The amplitude spectrum distribution of the induced ELF magnetic field components inside the SR cavity is found fully consistent with the measurements of the Huygens wave-field strength. Waiting for expected future in-situ exploration of Titan's lower atmosphere and the surface, the Huygens data are the only experimental means available to date for constraining the proposed model.

  9. Test evaluation of potential heat shield contamination of an Outer Planet Probe's atmospheric sampling system

    Science.gov (United States)

    Kessler, W. C.; Woeller, F. H.; Wilkins, M. E.

    1975-01-01

    An Outer Planets Probe which retains the charred heatshield during atmospheric descent must deploy a sampling tube through the heatshield to extract atmospheric samples for analysis. Once the sampling tube is deployed, the atmospheric samples ingested must be free of contaminant gases generated by the heatshield. Outgassing products such as methane and water vapor are present in planetary atmospheres and hence, ingestion of such species would result in gas analyzer measurement uncertainties. This paper evaluates the potential for, and design impact of, the extracted atmospheric samples being contaminated by heatshield outgassing products. Flight trajectory data for Jupiter, Saturn and Uranus entries are analyzed to define the conditions resulting in the greatest potential for outgassing products being ingested into the probe's sampling system. An experimental program is defined and described which simulates the key flow field features for a planetary flight in a ground-based test facility. The primary parameters varied in the test include: sampling tube length, injectant mass flow rate and angle of attack. Measured contaminant levels predict the critical sampling tube length for contamination avoidance. Thus, the study demonstrates the compatibility of a retained heatshield concept and high quality atmospheric trace species measurements.

  10. THIS -- next-generation mid-infrared remote sensing of planetary atmospheres using a tuneable heterodyne infrared spectrometer

    Science.gov (United States)

    Sonnabend, G.; Wirtz, D.; Vetterle, V.; Schieder, R.

    2003-12-01

    The Cologne spectrometer THIS (Tuneable Heterodyne Infrared Spectrometer) opens the mid-infrared wavelength region from 8 to 17 microns to ultra-high-resolution spectroscopy. The main scientific goal of THIS is to analyze highly resolved lineshape data of molecules (e.g. O3, NH3, CH4, N2O, HxCy etc.) to deduce physical parameters like wind velocities or height profiles of gases in either the Earth's or other planetary atmospheres. Also astronomical observations of non-solar-system IR-sources like IRC+10216 as well as the measurement of pure rotational transitions of H2 in the interstellar-medium from ground based telescopes are planned in the near future. THIS is a proposed second-generation instrument for the stratospheric observatory SOFIA. With a system noise temperature of less than three times the quantum limit THIS is the first widely tuneable and transportable infrared heterodyne receiver having a sensitivity equivalent to CO2-laser based heterodyne systems. A quantum-cascade-laser is used as local oscillator. Its radiation is superimposed to that from the signal by use of a Fabry-Perot ring-resonator to provide optimum efficiency. The frequency mixing is done by a Mercury-Cadmium-Telluride photomixer and spectral analysis with a resolution of up to 3x107 is performed by means of an Acousto-Optical spectrometer. We report on THIS' successful first observing run performed at the west auxiliary telescope at McMath-Pierce solar observatory on Kitt Peak/Arizona in 11/2002. Very weak non-LTE CO2 emission from the atmosphere of Venus have been observed as well as trace gases in Earth's atmosphere and molecular features in sunspots.

  11. Automated kinematic generator for surgical robotic systems.

    Science.gov (United States)

    Jung, David L; Dixon, Warren E; Pin, François G

    2004-01-01

    Unlike traditional assembly line robotic systems that have a fixed kinematic structure associated with a single tool for a structured task, next-generation robotic surgical assist systems will be required to use an array of end-effector tools. Once a robot is connected with a tool, the kinematic equations of motion are altered. Given the need to accommodate evolving surgical challenges and to alleviate the restrictions imposed by the confined minimally invasive environment, new surgical tools may resemble small flexible snakes rather than rigid, cable driven instruments. Connecting to these developing articulated tools will significantly alter the overall kinematic structure of a robotic system. In this paper we present a technique for real-time automated generation and evaluation of manipulator kinematic equations that exhibits the combined advantages of existing methods-speed and flexibility to kinematic change--without their disadvantages.

  12. Next Generation Multimedia Distributed Data Base Systems

    Science.gov (United States)

    Pendleton, Stuart E.

    1997-01-01

    The paradigm of client/server computing is changing. The model of a server running a monolithic application and supporting clients at the desktop is giving way to a different model that blurs the line between client and server. We are on the verge of plunging into the next generation of computing technology--distributed object-oriented computing. This is not only a change in requirements but a change in opportunities, and requires a new way of thinking for Information System (IS) developers. The information system demands caused by global competition are requiring even more access to decision making tools. Simply, object-oriented technology has been developed to supersede the current design process of information systems which is not capable of handling next generation multimedia.

  13. Reputation system for User Generated wireless podcasting

    DEFF Research Database (Denmark)

    Hu, Liang; Dittmann, Lars; Le Boudec, J-Y

    2008-01-01

    The user-generated podcasting service over mobile opportunistic networks can facilitate the user generated content dissemination while humans are on the move. However, in such a distributed and dynamic network environment, the design of efficient content forwarding and cache management schemes...... are challenging due to the lack of global podcast channel popularity information at each individual node. We design a distributed reputation system at each node for estimating the global channel popularity information which is significant for forwarding and cache management decision. Our simulation result shows...

  14. Protective, Modular Wave Power Generation System

    Energy Technology Data Exchange (ETDEWEB)

    Vvedensky, Jane M.; Park, Robert Y.

    2012-11-27

    The concept of small wave energy conversion modules that can be built into large, scalable arrays, in the same vein as solar panels, has been developed. This innovation lends itself to an organic business and development model, and enables the use of large-run manufacturing technology to reduce system costs. The first prototype module has been built to full-scale, and tested in a laboratory wave channel. The device has been shown to generate electricity and dissipate wave energy. Improvements need to be made to the electrical generator and a demonstration of an array of modules should be made in natural conditions.

  15. Dynamical systems generated by linear maps

    CERN Document Server

    Dolićanin, Ćemal B

    2014-01-01

    The book deals with dynamical systems, generated by linear mappings of finite dimensional spaces and their applications. These systems have a relatively simple structure from the point of view of the modern dynamical systems theory. However, for the dynamical systems of this sort, it is possible to obtain explicit answers to specific questions being useful in applications. The considered problems are natural and look rather simple, but in reality in the course of investigation, they confront users with plenty of subtle questions, and their detailed analysis needs a substantial effort. The problems arising are related to linear algebra and dynamical systems theory, and therefore, the book can be considered as a natural amplification, refinement and supplement to linear algebra and dynamical systems theory textbooks.

  16. Towards a full Atmospheric Calibration system for the Cherenkov Telescope Array

    CERN Document Server

    Doro, M; Blanch, O; Font, LL; Garrido, D; Lopez-Oramas, A

    2013-01-01

    The current generation of Cherenkov telescopes is mainly limited in their gamma-ray energy and flux reconstruction by uncertainties in the determination of atmospheric parameters. The Cherenkov Telescope Array (CTA) aims to provide high-precision data extending the duty cycle as much as possible. To reach this goal, it is necessary to continuously and precisely monitor the atmosphere by means of remote-sensing devices, which are able to provide altitude-resolved and wavelength-dependent extinction factors, sensitive up to the tropopause and higher. Raman LIDARs are currently the best suited technology to achieve this goal with one single instrument. However, the synergy with other instruments like radiometers, solar and stellar photometers, all-sky cameras, and possibly radio-sondes is desirable in order to provide more precise and accurate results, and allows for weather forecasts and now-casts. In this contribution, we will discuss the need and features of such multifaceted atmospheric calibration systems.

  17. Unraveling the Complexities of the Upper Atmosphere as a System

    Science.gov (United States)

    Fuller-Rowell, T. J.

    2016-12-01

    The Earth's upper atmosphere responds as a system to external forcing from the Sun, magnetosphere, and lower atmosphere. The underlying system components comprise a highly dynamic, non-linear neutral fluid supporting fast propagating wave fields, advective transport, dissipation, and chemical changes, coupled to an active plasma constrained by all-encompassing magnetic and electric fields. More importantly, the plasma and more massive neutral gas are intimately coupled. Ion-neutral coupling can drive winds ten-times hurricane strength making inertia a dominant force; it can sometimes wipe out 90% of the plasma, and at other times allow plasma content to explode with dangerous consequences. Ion-neutral dissipation can result in intense heating, allowing the atmosphere to expand to double its normal size, dragging Earth orbiting satellites to the ground. The thermospheric dynamo, ultimately driven by the solar and magnetosphere dynamos, redistributes equatorial plasma and can drive structure, steep gradients, and irregularities. A single satellite sampling the medium is suitable for uncovering perhaps one or two of the many interacting processes, in what could be called discovery mode science. Without a three-dimensional imaging capability, a single satellite cannot explore the interaction and balance between the multiple of processes actually present. Unraveling the system-wide or global response requires multi-point in-situ constellation-type measurements, together with available two-dimensional imaging. Modeling the system can create an illusion of understanding, but until we really look we will never know.

  18. A Next Generation Atmospheric Prediction System for the Navy

    Science.gov (United States)

    2015-09-30

    capability to be applied on the globe at high resolution, as well as for limited area applications (e.g., urban scale, regional climate etc...energy model, radiation, subgrid-scale mixing, cloud fraction, and planetary boundary layer. The successful simulation represent the first global weather...resolution model capturing scales ranging from planetary to clouds can be exploited for a number of warfare areas, including Intelligence, Surveillance

  19. Development of the atmospheric correction algorithm for the next generation geostationary ocean color sensor data

    Science.gov (United States)

    Lee, Kwon-Ho; Kim, Wonkook

    2017-04-01

    The geostationary ocean color imager-II (GOCI-II), designed to be focused on the ocean environmental monitoring with better spatial (250m for local and 1km for full disk) and spectral resolution (13 bands) then the current operational mission of the GOCI-I. GOCI-II will be launched in 2018. This study presents currently developing algorithm for atmospheric correction and retrieval of surface reflectance over land to be optimized with the sensor's characteristics. We first derived the top-of-atmosphere radiances as the proxy data derived from the parameterized radiative transfer code in the 13 bands of GOCI-II. Based on the proxy data, the algorithm has been made with cloud masking, gas absorption correction, aerosol inversion, computation of aerosol extinction correction. The retrieved surface reflectances are evaluated by the MODIS level 2 surface reflectance products (MOD09). For the initial test period, the algorithm gave error of within 0.05 compared to MOD09. Further work will be progressed to fully implement the GOCI-II Ground Segment system (G2GS) algorithm development environment. These atmospherically corrected surface reflectance product will be the standard GOCI-II product after launch.

  20. Cold atmospheric plasma jet-generated RONS and their selective effects on normal and carcinoma cells.

    Science.gov (United States)

    Kim, Sun Ja; Chung, T H

    2016-02-03

    Cold atmospheric helium plasma jets were fabricated and utilized for plasma-cell interactions. The effect of operating parameters and jet design on the generation of specific reactive oxygen and nitrogen species (RONS) within cells and cellular response were investigated. It was found that plasma treatment induced the overproduction of RONS in various cancer cell lines selectively. The plasma under a relatively low applied voltage induced the detachment of cells, a reduction in cell viability, and apoptosis, while the plasma under higher applied voltage led to cellular necrosis in our case. To determine whether plasma-induced reactive oxygen species (ROS) generation occurs through interfering with mitochondria-related cellular response, we examined the plasma effects on ROS generation in both parental A549 cells and A549 ρ(0) cells. It was observed that cancer cells were more susceptible to plasma-induced RONS (especially nitric oxide (NO) and nitrogen dioxide (NO2(-)) radicals) than normal cells, and consequently, plasma induced apoptotic cell responses mainly in cancer cells.

  1. Development of micro pulse lidar system for atmospheric monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Hyung Ki; Song, Kyu Seok; Lee, Jong Min; Lee, Yong Ju; Kim, Duk Hyeon; Nam, Sung Mo; Go, Do Kyung; Yang, Gi Ho; Hong, Kyang He

    1999-12-01

    A compact small micro pulse lidar system is developed for atmospheric monitoring. The developed system can be operated during 24 hrs for four seasons. The maximum detection distance is 5 km at day time and 10 km at night. Specially, the problem of eye safety is solved by using diode pumped low pulse-energy Nd:YAG laser. Two rotational axis, vertical and horizontal, is chosen for 3D mapping of the atmospheric aerosol. The spatial resolution can be optionally changed from 5 m to 300 m, but time resolution which changes from several sec to several minutes depends on the detection distance and background signal. To analyze the obtained lidar signal, processing software is developed and applied to the lidar signal obtained near the chimney. Vertical lidar signal is also obtained and from this data we can find the thickness and change of cloud. (author)

  2. Converters for Distributed Power Generation Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Yang, Yongheng

    2015-01-01

    Power electronics technology has become the enabling technology for the integration of distributed power generation systems (DPGS) such as offshore wind turbine power systems and commercial photovoltaic power plants. Depending on the applications, a vast array of DPGS-based power converter...... presents an overview of the power converters for the DPGS, mainly based on wind turbine systems and photovoltaic systems, covering a wide range of applications. Moreover, the modulation schemes and interfacing power filters for the power converters are also exemplified. Finally, the general control...... topologies has been developed and more are coming into the market in order to achieve an efficient and reliable power conversion from the renewables. In addition, stringent demands from both the distribution system operators and the consumers have been imposed on the renewable-based DPGS. This article...

  3. Model JC-1 Laser System for Monitoring Atmospheric Pollution,

    Science.gov (United States)

    2007-11-02

    differential absorption mode atmospheric pollution laser monitoring system, in which a phase locking technique and single board computer are used for...amplification 1 3. synchronous demodulation 2 4. phase locking amplification 2 5. single board computer 6. function logging Instrument 7. oscillator...were then fed into a DBJ-Z80 single - board computer to undergo a multiple averaging process before going through functional operation, and were logged

  4. Generating Interpretable Fuzzy Systems for Classification Problems

    Directory of Open Access Journals (Sweden)

    Juan A. Contreras-Montes

    2009-12-01

    Full Text Available This paper presents a new method to generate interpretable fuzzy systems from training data to deal with classification problems. The antecedent partition uses triangular sets with 0.5 interpolations avoiding the presence of complex overlapping that happens in another method. Singleton consequents are generated form the projection of the modal values of each triangular membership function into the output space. Least square method is used to adjust the consequents. The proposed method gets a higher average classification accuracy rate than the existing methods with a reduced number of rules andparameters and without sacrificing the fuzzy system interpretability. The proposed approach is applied to two classical classification problems: Iris data and the Wisconsin Breast Cancer classification problem.

  5. Educating the next generation of atmospheric scientists within a European Network of Excellence

    Science.gov (United States)

    Schuepbach, E.; Uherek, E.; Ladstätter-Weissenmayer, A.; Jacob, M. J.

    In order to promote the next generation of atmospheric scientists, the task Training and Education (T&E) in ACCENT, the European Network of Excellence in Atmospheric Composition Change ( www.accent-network.org) has developed and implemented an Integrated Learning Environment (ILE). For school teachers and their students, the Internet-based "Global Change Magazine" provides up-to-date and freely accessible scientific material in English and five other languages. Additionally, T&E has produced online teaching material for early-career scientists. These e-learning modules are now being used in University Master's courses across Europe. T&E also organised training events for early-career scientists, combining scientific content with development in transferable skills, to focus on interdisciplinary collaboration, interaction with senior scientists, communication with stakeholders, and dissemination to the general public. Evaluation based on participant feedback evidences the effectiveness of these events, e.g., in terms of motivation to remain in the field. Methodologies and materials from T&E are being published in a Handbook on Best Practice, intended for both educators and scientists around the globe who are involved in education in the field of air quality and climate change science.

  6. Atmospheric and Fundamental Parameters of Stars in Hubble's Next Generation Spectral Library

    Science.gov (United States)

    Heap, Sally

    2010-01-01

    Hubble's Next Generation Spectral Library (NGSL) consists of R approximately 1000 spectra of 374 stars of assorted temperature, gravity, and metallicity. We are presently working to determine the atmospheric and fundamental parameters of the stars from the NGSL spectra themselves via full-spectrum fitting of model spectra to the observed (extinction-corrected) spectrum over the full wavelength range, 0.2-1.0 micron. We use two grids of model spectra for this purpose: the very low-resolution spectral grid from Castelli-Kurucz (2004), and the grid from MARCS (2008). Both the observed spectrum and the MARCS spectra are first degraded in resolution to match the very low resolution of the Castelli-Kurucz models, so that our fitting technique is the same for both model grids. We will present our preliminary results with a comparison with those from the Sloan/Segue Stellar Parameter Pipeline, ELODIE, and MILES, etc.

  7. Generation and characterization of OH and O radicals by atmospheric pressure steam/oxygen plasma

    CERN Document Server

    Roy, N C; Alam, M K; Talukder, M R

    2016-01-01

    Atmospheric pressure steam/oxygen plasma is generated by a 88 Hz, 6kV AC power supply. The properties of the produced plasma are investigated by optical emission spectroscopy (OES). The relative intensity, rotational, vibrational, excitation temperatures and electron density are studied as function of applied voltage, electrode spacing and oxygen flow rate. The rotational and vibrational temperatures are determined simulating the bands with the aid of LIFBASE simulation software. The excitation temperature is obtained from the CuI transition taking non-thermal equilibrium condition into account employing intensity ratio method. The electron density is approximated from the H_{\\alpha} Stark broadening using the Voigt profile fitting method. It is observed that the rotational and vibrational temperatures are decreased with increasing electrode spacing and O2 flow rate, but increased with the applied voltage. The excitation temperature is found to increase with increasing applied voltage and O2 flow rate, but de...

  8. Laser-Induced Acoustic Desorption Atmospheric Pressure Photoionization via VUV-Generating Microplasmas.

    Science.gov (United States)

    Benham, Kevin; Hodyss, Robert; Fernández, Facundo M; Orlando, Thomas M

    2016-11-01

    We demonstrate the first application of laser-induced acoustic desorption (LIAD) and atmospheric pressure photoionization (APPI) as a mass spectrometric method for detecting low-polarity organics. This was accomplished using a Lyman-α (10.2 eV) photon generating microhollow cathode discharge (MHCD) microplasma photon source in conjunction with the addition of a gas-phase molecular dopant. This combination provided a soft desorption and a relatively soft ionization technique. Selected compounds analyzed include α-tocopherol, perylene, cholesterol, phenanthrene, phylloquinone, and squalene. Detectable surface concentrations as low as a few pmol per spot sampled were achievable using test molecules. The combination of LIAD and APPI provided a soft desorption and ionization technique that can allow detection of labile, low-polarity, structurally complex molecules over a wide mass range with minimal fragmentation. Graphical Abstract ᅟ.

  9. Laser-Induced Acoustic Desorption Atmospheric Pressure Photoionization via VUV-Generating Microplasmas

    Science.gov (United States)

    Benham, Kevin; Hodyss, Robert; Fernández, Facundo M.; Orlando, Thomas M.

    2016-11-01

    We demonstrate the first application of laser-induced acoustic desorption (LIAD) and atmospheric pressure photoionization (APPI) as a mass spectrometric method for detecting low-polarity organics. This was accomplished using a Lyman-α (10.2 eV) photon generating microhollow cathode discharge (MHCD) microplasma photon source in conjunction with the addition of a gas-phase molecular dopant. This combination provided a soft desorption and a relatively soft ionization technique. Selected compounds analyzed include α-tocopherol, perylene, cholesterol, phenanthrene, phylloquinone, and squalene. Detectable surface concentrations as low as a few pmol per spot sampled were achievable using test molecules. The combination of LIAD and APPI provided a soft desorption and ionization technique that can allow detection of labile, low-polarity, structurally complex molecules over a wide mass range with minimal fragmentation.

  10. Nigel: A Systemic Grammar for Text Generation.

    Science.gov (United States)

    1983-02-01

    in the logical component). Henrici [ Henrici 811 observes that "linear recursion is rather more troublesome" than recursion through embedding (which...notation defined by Henrici [ Henrici 81]. However, we have neither exhausted the grammar nor reached the lexicon. This section will present how the...Halliday, M. A. K., Language as Social Semiotic, University Park Press, Baltimore, 1978 [ Henrici 81] Henrici , A., "Some notes on the systemic generation of

  11. An atmosphere monitoring system for the Sardinia radio telescope

    Science.gov (United States)

    Buffa, F.; Bolli, P.; Sanna, G.; Serra, G.

    2017-01-01

    The Sardinia radio telescope (SRT) is a new facility managed by the Italian National Institute for Astrophysics (INAF). SRT will detect the extremely faint radio wave signals emitted by astronomical objects in a wide frequency range from decimeter to millimeter wavelengths. Especially at high frequencies (>10 GHz), specific weather conditions and interactions between signal and atmospheric constituents (mainly water and oxygen molecules) affect the radio astronomic observation reducing the antenna performances. Thus, modern ground-based telescopes are usually equipped with systems able to examine in real-time several atmospheric parameters (opacity, integrated water vapor, etc.), and in some cases to forecast the weather conditions (wind, rain, snow, etc.), in order to ensure the antenna safety and support the schedule of the telescope observations. Here, we describe the atmosphere monitoring system (AMS) realized with the aim to improve the SRT operative efficiency. It consists of a network of different sensors such as radiometers, radiosondes, weather stations, GPS and some well-established weather models. After a validation of the scheme, we successfully tested the AMS in two real practical scenarios, comparing the AMS outcomes with those of independent techniques. In the first one we were able to detect an incoming storm front applying different techniques (GPS, radiometer and the weather forecast model), while in the last one we modeled the SRT antenna system temperature at 22 GHz processing the AMS data set.

  12. Synchrotron radiation lithography system in an atmospheric environment (invited)

    Science.gov (United States)

    Okada, K.; Kouno, E.; Nomura, E.; Suzuki, K.; Fujii, K.; Tanaka, Y.; Iwata, J.; Kawase, Y.

    1989-07-01

    The atmospheric environmental exposure system for synchrotron radiation (SR) lithography has been integrated using the Photon Factory storage ring (2.5 GeV). The system, composed of a highly reliable beamline, an SR extracting chamber and a prototype SR stepper, aims at attaining higher accuracy and throughput. Based on a fail-safe mechanism notion, a double-vacuum protection system, in which two sets of a fast closing valve and acoustic delay line are installed in the main beamline and branch beamline, respectively, has been organized. Vacuum breakdown tests indicated that any vacuum breakdown, a beryllium (Be) window rupture in the worst case, exerts little influence on the storage ring ultrahigh vacuum. The SR extracting chamber, equipped with a Be window and an extraction window, is filled with helium at atmospheric pressure. Particularly, the 50-μm-thick, 35-mm-diam Be window, vacuum-sealed by a Viton O-ring, was preliminarily employed and, so far, has operated successfully, giving a 25-mm square exposure area. In terms of practical availability and simplicity, the SR stepper in an atmospheric environment has been constructed. A novel differential mode linear Fresnel zone plate alignment method, which can detect an alignment error between a mask and a wafer during exposure, was developed.

  13. Mass identification of the neutral products generated in the plasma treatment of polluted atmospheres

    Science.gov (United States)

    Seymour, David

    2013-09-01

    Plasmas produced using Dielectric Barrier Discharge (DBD) devices are very effective in the abatement of air pollution resulting from, for example, the emission of volatile organic compounds (VCOs) by a range of industrial and agricultural processes. The development and monitoring of effective DBD systems can be investigated by advanced mass spectrometric methods specifically configured for analysis at high and atmospheric pressures The present work involves the operation of a small DBD reactor which uses either a helium or nitrogen carrier gas to sustain the plasma to which may be added reactive gases, such as oxygen, as well as samples of pollutants such as chlorinated hydrocarbons, including trichloroethylene. The mass spectrometric analysis was performed using a specially configured system manufactured by Hiden Analytical Ltd. The DBD source may also be combined with a catalyst for plasma-enhanced catalysis. The neutral products of the reactions proceeding in the plasma at atmospheric pressure are sampled through the capillary sampling system which also reduces the pressure of the gas mixture delivered to the ionisation source of the quadrupole mass spectrometer. The ions produced are subsequently mass identified. We describe typical data and comment on the advantages of this technique.

  14. NEXT GENERATION GAS TURBINE SYSTEMS STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Benjamin C. Wiant; Ihor S. Diakunchak; Dennis A. Horazak; Harry T. Morehead

    2003-03-01

    Under sponsorship of the U.S. Department of Energy's National Energy Technology Laboratory, Siemens Westinghouse Power Corporation has conducted a study of Next Generation Gas Turbine Systems that embraces the goals of the DOE's High Efficiency Engines and Turbines and Vision 21 programs. The Siemens Westinghouse Next Generation Gas Turbine (NGGT) Systems program was a 24-month study looking at the feasibility of a NGGT for the emerging deregulated distributed generation market. Initial efforts focused on a modular gas turbine using an innovative blend of proven technologies from the Siemens Westinghouse W501 series of gas turbines and new enabling technologies to serve a wide variety of applications. The flexibility to serve both 50-Hz and 60-Hz applications, use a wide range of fuels and be configured for peaking, intermediate and base load duty cycles was the ultimate goal. As the study progressed the emphasis shifted from a flexible gas turbine system of a specific size to a broader gas turbine technology focus. This shift in direction allowed for greater placement of technology among both the existing fleet and new engine designs, regardless of size, and will ultimately provide for greater public benefit. This report describes the study efforts and provides the resultant conclusions and recommendations for future technology development in collaboration with the DOE.

  15. Effects of Maternal Exposure to Atmospheric Particulates during Pregnancy and Lactation Period on Central Nervous System of Filial Generation among Rats%妊娠期和哺乳期暴露于大气颗粒物对仔鼠中枢神经系统的影响

    Institute of Scientific and Technical Information of China (English)

    李久存; 魏永杰; 陈田; 钱琴; 郭建; 宋艳双; 胡洁琼; 贾光

    2011-01-01

    To study the effects on learning and memory ability and the content changes of monoamine neurotransmitter in hippocampus of filial generation when maternal rats exposed to atmospheric particulates during pregnancy and lactation period. Methods During Dec. 28th, 2009 to Feb. 7th, 2010, the experimental group was exposed to actual atmosphere in some area of Beijing in pregnancy and lactation period, while the control group exposed to atmosphere filtered without particulates. For the three weeks old young rats, the learning and memory ability were examined by using Morris water maze, while the content changes of monoamine neurotransmitter in hippocampus of neonatal mice were determined. Results In the place navigation period, the potential time finding flat incubation for offsprings in exposed group was significantly longer than that in the control group; in the spatial probe test period, the time of crossing the quadrant with flat and the traversing time decreased in exposed group. The contents of norepinephrine (NE) and 5-hydroxytryptamine(5-HT) in hippocampos of exposed rats were significantly increased, while dopamine (DA) was decreased but only with statistical significance in male rats.Conclusion Exposure to ambient atmospheric particulates in pregnancy and lactation periods can affect the central nervous system function of filial generation rats.%目的 研究母鼠在孕期及子代哺乳期暴露于大气颗粒物对仔鼠学习记忆能力以及海马单胺类神经递质含量的影响.方法 选择健康成年妊娠0d(见栓当天)SD大鼠,于2009年12月28日-2010年2月7日,采用平行的两个暴露箱,将妊娠期和哺乳期的暴露组孕鼠暴露于室外大气,对照组孕鼠暴露于经过滤装置滤除颗粒物后的大气;对其3周龄仔鼠用Morris水迷宫检测学习记忆能力,并检测仔鼠海马组织单胺类神经递质含量.结果 暴露组仔鼠寻找平台潜伏期时间长于对照组(P<0.001).暴露组仔鼠海马

  16. Goldstone Solar System Radar Waveform Generator

    Science.gov (United States)

    Quirk, Kevin J.; Patawaran, Ferze D.; Nguyen, Danh H.; Nguyen, Huy

    2012-01-01

    Due to distances and relative motions among the transmitter, target object, and receiver, the time-base between any transmitted and received signal will undergo distortion. Pre-distortion of the transmitted signal to compensate for this time-base distortion allows reception of an undistorted signal. In most radar applications, an arbitrary waveform generator (AWG) would be used to store the pre-calculated waveform and then play back this waveform during transmission. The Goldstone Solar System Radar (GSSR), however, has transmission durations that exceed the available memory storage of such a device. A waveform generator capable of real-time pre-distortion of a radar waveform to a given time-base distortion function is needed. To pre-distort the transmitted signal, both the baseband radar waveform and the RF carrier must be modified. In the GSSR, this occurs at the up-conversion mixing stage to an intermediate frequency (IF). A programmable oscillator (PO) is used to generate the IF along with a time-varying phase component that matches the time-base distortion of the RF carrier. This serves as the IF input to the waveform generator where it is mixed with a baseband radar waveform whose time-base has been distorted to match the given time-base distortion function producing the modulated IF output. An error control feedback loop is used to precisely control the time-base distortion of the baseband waveform, allowing its real-time generation. The waveform generator produces IF modulated radar waveforms whose time-base has been pre-distorted to match a given arbitrary function. The following waveforms are supported: continuous wave (CW), frequency hopped (FH), binary phase code (BPC), and linear frequency modulation (LFM). The waveform generator takes as input an IF with a time varying phase component that matches the time-base distortion of the carrier. The waveform generator supports interconnection with deep-space network (DSN) timing and frequency standards, and

  17. Comparison of next-generation sequencing systems.

    Science.gov (United States)

    Liu, Lin; Li, Yinhu; Li, Siliang; Hu, Ni; He, Yimin; Pong, Ray; Lin, Danni; Lu, Lihua; Law, Maggie

    2012-01-01

    With fast development and wide applications of next-generation sequencing (NGS) technologies, genomic sequence information is within reach to aid the achievement of goals to decode life mysteries, make better crops, detect pathogens, and improve life qualities. NGS systems are typically represented by SOLiD/Ion Torrent PGM from Life Sciences, Genome Analyzer/HiSeq 2000/MiSeq from Illumina, and GS FLX Titanium/GS Junior from Roche. Beijing Genomics Institute (BGI), which possesses the world's biggest sequencing capacity, has multiple NGS systems including 137 HiSeq 2000, 27 SOLiD, one Ion Torrent PGM, one MiSeq, and one 454 sequencer. We have accumulated extensive experience in sample handling, sequencing, and bioinformatics analysis. In this paper, technologies of these systems are reviewed, and first-hand data from extensive experience is summarized and analyzed to discuss the advantages and specifics associated with each sequencing system. At last, applications of NGS are summarized.

  18. Next Generation CAD/CAM/CAE Systems

    Science.gov (United States)

    Noor, Ahmed K. (Compiler); Malone, John B. (Compiler)

    1997-01-01

    This document contains presentations from the joint UVA/NASA Workshop on Next Generation CAD/CAM/CAE Systems held at NASA Langley Research Center in Hampton, Virginia on March 18-19, 1997. The presentations focused on current capabilities and future directions of CAD/CAM/CAE systems, aerospace industry projects, and university activities related to simulation-based design. Workshop attendees represented NASA, commercial software developers, the aerospace industry, government labs, and academia. The workshop objectives were to assess the potential of emerging CAD/CAM/CAE technology for use in intelligent simulation-based design and to provide guidelines for focused future research leading to effective use of CAE systems for simulating the entire life cycle of aerospace systems.

  19. Evaluation of atmospheric density models and preliminary functional specifications for the Langley Atmospheric Information Retrieval System (LAIRS)

    Science.gov (United States)

    Lee, T.; Boland, D. F., Jr.

    1980-01-01

    This document presents the results of an extensive survey and comparative evaluation of current atmosphere and wind models for inclusion in the Langley Atmospheric Information Retrieval System (LAIRS). It includes recommended models for use in LAIRS, estimated accuracies for the recommended models, and functional specifications for the development of LAIRS.

  20. Atmospheric evaporation in super-Earth exoplanet systems

    Science.gov (United States)

    Moller, Spencer; Miller, Brendan P.; Gallo, Elena; Wright, Jason; Poppenhaeger, Katja

    2017-01-01

    We investigate the influence of stellar activity on atmospheric heating and evaporation in four super-Earth exoplanets: HD 97658 b, GJ 1214 b, 55 Cnc e, and CoRoT-7 b. We use X-ray observations of the host stars to estimate planetary mass loss. We extracted net count rates from a soft band image, converted it to flux using PIMMS for a standard coronal model, calculated the intrinsic stellar luminosity, and estimated the current-epoch mass-loss rate and the integrated mass lost. Our aim is to determine under what circumstances current super-Earths will have experienced significant mass loss through atmospheric irradiation over the system lifetime. We hypothesize that closely-orbiting exoplanets receiving the greatest amount of high-energy stellar radiation will also tend to be sculpted into lower mass and more dense remnant cores.

  1. Turbulence Generation in the Atmospheric Boundary Layer and Limitations of the Monin-Obukhov Similarity Theory

    Science.gov (United States)

    Sun, Jielun; Lenschow, Donald; LeMone, Margaret; Mahrt, Larry

    2015-04-01

    Turbulent fluxes from the Cooperative Atmosphere-Surface Exchange Study in 1999 (CASES-99) field experiment are further analyzed for both day- and nighttime as a follow-on to the investigation of the nighttime turbulence in Sun et al. (2012). The behavior of momentum and heat fluxes is investigated as functions of wind speed and the bulk temperature difference between observation heights and the surface. Vertical variations of momentum and heat flux at a given height z are correlated and are explained in terms of the energy and heat balance in a layer above the ground surface in which the surface heating/cooling and momentum sink need to be included. In addition, the surface also plays an important role in constraining the size of the dominant turbulent eddies, which is directly related to turbulence strength and the length scale of turbulence generation. The turbulence generation is not related to local vertical gradients especially under neutral condition as assumed in Monin-Obukhov similarity theory. Based on the observed relationships between momentum and heat fluxes, a new bulk formula for turbulence parameterization is developed to mainly examine the above-mentioned surface effects on vertical variation of turbulent momentum and heat fluxes. The new understanding of the observed relationships between these turbulent variables and mean variables explains the observed nighttime turbulence regime change observed in Sun et al. (2012) as well as the daytime momentum and heat flux variations with height up to the maximum observation height of 55 m.

  2. Next Generation Flight Controller Trainer System

    Science.gov (United States)

    Arnold, Scott; Barry, Matthew R.; Benton, Isaac; Bishop, Michael M.; Evans, Steven; Harvey, Jason; King, Timothy; Martin, Jacob; Mercier, Al; Miller, Walt; Payne, Dan L.; Phu, Hanh; Thompson, James C.; Aadsen, Ron

    2008-01-01

    The Next Generation Flight Controller Trainer (NGFCT) is a relatively inexpensive system of hardware and software that provides high-fidelity training for spaceshuttle flight controllers. NGFCT provides simulations into which are integrated the behaviors of emulated space-shuttle vehicle onboard general-purpose computers (GPCs), mission-control center (MCC) displays, and space-shuttle systems as represented by high-fidelity shuttle mission simulator (SMS) mathematical models. The emulated GPC computers enable the execution of onboard binary flight-specific software. The SMS models include representations of system malfunctions that can be easily invoked. The NGFCT software has a flexible design that enables independent updating of its GPC, SMS, and MCC components.

  3. 基于 System Generator 的 UART 通讯%UART Communication Based on System Generator

    Institute of Scientific and Technical Information of China (English)

    于中权; 王一诚; 吴大庆; 陈习元; 张晓亮; 梁永青

    2015-01-01

    基于System Generator 系统级建模工具在Matlab/Simulink环境下完成了UART通讯模块的建模,并生成位流文件下载到Spartan-3E开发板的FPGA芯片中,实现UART通讯数据发送和接收功能。实验结果表明,System Generator 系统级建模工具不仅消除了原先系统工程师与软硬件工程师之间的隔阂,而且简化了传统的FPGA开发流程。%The paper introduces the use of System Generator of Xilinx that is system level modeling tool in the MATLAB /Simulink environment for the completion of algorithm modeling of the UART procedure , generates the corresponding code to the FPGA , and realizes the function between UART communication data sending and receiving .Experiment results show that the System Genera-tor as a system level modeling tool is not only to eliminate the gap between the original system engineers and hardware and soft -ware engineers , but also to simplify the traditional development process of the FPGA .

  4. Detection of non-standard atmospheric effects in FSO systems

    Science.gov (United States)

    Wilfert, Otakar; Poliak, Juraj; Barcík, Peter; Arce-Diego, José L.; Fanjul-Vélez, Félix; Salas-García, Irene; Ortega Quijano, Noé

    2013-09-01

    Modern free-space optical (FSO) communication systems in many aspects overcome wire or radio communications. They offer a license-free operation and a large bandwidth. Operation of outdoor FSO links struggles with many atmospheric phenomena that deteriorate phase and amplitude of the transmitted optical beam. Thanks to the recent advancing development, these effects are more or less well understood and described. Goal driven research increased the link availability. Besides increasing the availability of data links it is necessary to focus on the accuracy and reliability of testing optical links. Research of the data optical links is focused on the transmission of a large amount of data whereas the testing FSO link is designed to achieve maximal resolution and sensitivity thus improving accuracy and repeatability of the atmospheric effects measurement. Given the fact that testing links are located in the measured media, they are themselves influenced by it. Phenomena such as the condensation on transceiver windows (rain, frost) and the deviation of the optical beam path caused by the wind are referred to as non-standard effects. Non-standard effects never occur independently; therefore we must always verify the cross-sensitivity of the testing link. In the paper we respond to an increasing number of articles dealing with influence of the atmosphere on the link but ignoring the cross-sensitivity of the testing link on other variables than tested. In conclusion, we carry out qualitative and quantitative analysis of self-identified non-standard effects.

  5. A Direct Measurement of Atmospheric Dispersion in N-band Spectra: Implications for Mid-IR Systems on ELTs

    Science.gov (United States)

    Skemer, Andrew J.; Hinz, Philip M.; Hoffmann, William F.; Close, Laird M.; Kendrew, Sarah; Mathar, Richard J.; Stuik, Remko; Greene, Thomas P.; Woodward, Charles E.; Kelley, Michael S.

    2009-08-01

    Adaptive optics will almost completely remove the effects of atmospheric turbulence at 10 μm on the Extremely Large Telescope (ELT) generation of telescopes. In this article, we observationally confirm that the next most important limitation to image quality is atmospheric dispersion, rather than telescope diffraction. By using the 6.5 m MMT with its unique mid-IR adaptive optics system, we measure atmospheric dispersion in the N band with the newly commissioned spectroscopic mode on MIRAC4-BLINC. Our results indicate that atmospheric dispersion is generally linear in the N band, although there is some residual curvature. We compare our measurements to theory, and make predictions for ELT Strehls and image FHWM with and without an atmospheric dispersion corrector (ADC). We find that for many mid-IR applications, an ADC will be necessary on ELTs. The observations reported here were obtained at the MMT Observatory, a facility operated jointly by the Smithsonian Institution and the University of Arizona.

  6. Oceanic contributions from tropical upwelling systems to atmospheric halogens

    Science.gov (United States)

    Ziska, Franziska; Hepach, Helmke; Stemmler, Irene; Quack, Birgit; Atlas, Elliot; Fuhlbrügge, Steffen; Bracher, Astrid; Tegtmeier, Susann; Krüger, Kirstin

    2014-05-01

    Short lived halogenated substances (halocarbons) from the oceans contribute to atmospheric halogens, where they are involved in ozone depletion and aerosol formation. Oceanic regions that are characterized by high biological activity are often associated with increased halocarbon abundance of e.g. bromoform (CHBr3) and dibromomethane (CH2Br2), representing the main contributors to atmospheric organic bromine. Apart from biological production, photochemical pathways play an important role in the formation of methyl iodide (CH3I), the most abundant organoiodine in the marine atmosphere. Recently, the contribution of biogenic diiodomethane (CH2I2) and chloroiodomethane (CH2ClI) to atmospheric organic iodine has been estimated to be similarly significant as CH3I. In the tropics, rapid uplift of surface air can transport these short-lived compounds into the upper troposphere and into the stratosphere. Oceanic upwelling systems off Mauritania, Peru and in the equatorial Atlantic might therefore potentially contribute large amounts of halocarbons to the stratosphere. Concentrations and emissions of iodo- and bromocarbons from several SOPRAN campaigns in different tropical upwelling systems, the Mauritanian and the equatorial upwelling in the Atlantic, as well as the Peruvian upwelling in the Pacific, will be presented. Processes contributing to halocarbon occurrence in the water column, as well as biological and physical factors influencing their emission into the atmosphere are investigated (Fuhlbrügge, et al. 2013; Hepach et al., 2013). We will present the relative contribution of the upwelling systems to global air-sea fluxes from different modelling studies. The data based bottom-up emissions from Ziska et al. (2013) will be compared to model simulated halocarbons. The model is a global three-dimensional ocean general circulation model with an ecosystem model and halocarbon module embedded (MPIOM/HAMOCC). It resolves CH3I and CHBr3 production, degradation, and

  7. Integrated control of next generation power system

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2010-02-28

    The multi-agent system (MAS) approach has been applied with promising results for enhancing an electric power distribution circuit, such as the Circuit of the Future as developed by Southern California Edison. These next generation power system results include better ability to reconfigure the circuit as well as the increased capability to improve the protection and enhance the reliability of the circuit. There were four main tasks in this project. The specific results for each of these four tasks and their related topics are presented in main sections of this report. Also, there were seven deliverables for this project. The main conclusions for these deliverables are summarized in the identified subtask section of this report. The specific details for each of these deliverables are included in the “Project Deliverables” section at the end of this Final Report.

  8. Towards 5th Generation Wireless Communication Systems

    Institute of Scientific and Technical Information of China (English)

    Nicola Marchetti

    2015-01-01

    This paper introduces the general landscape of next⁃generation wireless communication systems (5G), including the impetus and requirements of 5G and the candidate technologies that might help 5G achieve its goals. The following areas, which the author considers particularly relevant, are discussed: detection of and access to free spectrum over bands of a heterogeneous nature, ex⁃treme densification of networks (massive base station deployments), extreme increase in the number of antennas in base station ar⁃rays and their interaction with a novel waveform, integration of both wireless and optical sides of telecom networks, and study of wireless networks from the perspective of complex systems science. The author discusses recent research conducted by his team in each of these research areas.

  9. Simulation of atmospheric turbulence for optical systems with extended sources.

    Science.gov (United States)

    Safari, Majid; Hranilovic, Steve

    2012-11-01

    In this paper, the method of random wave vectors for simulation of atmospheric turbulence is extended to 2D×2D space to provide spatial degrees of freedom at both input and output planes. The modified technique can thus simultaneously simulate the turbulence-induced log-amplitude and phase distortions for optical systems with extended sources either implemented as a single large aperture or multiple apertures. The reliability of our simulation technique is validated in different conditions and its application is briefly investigated in a multibeam free-space optical communication scenario.

  10. A lidar system for measuring atmospheric pressure and temperature profiles

    Science.gov (United States)

    Schwemmer, Geary K.; Dombrowski, Mark; Korb, C. Laurence; Milrod, Jeffry; Walden, Harvey

    1987-01-01

    The design and operation of a differential absorption lidar system capable of remotely measuring the vertical structure of tropospheric pressure and temperature are described. The measurements are based on the absorption by atmospheric oxygen of the spectrally narrowband output of two pulsed alexandrite lasers. Detailed laser output spectral characteristics, which are critical to successful lidar measurements, are presented. Spectral linewidths of 0.026 and 0.018 per cm for the lasers were measured with over 99.99 percent of the energy contained in three longitudinal modes.

  11. An Air Jet Distortion Generation System

    Directory of Open Access Journals (Sweden)

    M. Sivapragasam

    2014-01-01

    Full Text Available An air jet distortion generation system is developed to simulate the distorted flow field ahead of gas turbine engines in ground test facility. The flow field of a system of four jets arranged circumferentially and issuing into a confined counterflow was studied experimentally and numerically. The total pressure distortion parameters were evaluated at the Aerodynamic Interface Plane (AIP for several values of mass flow ratios. Since the total pressure loss distribution at the AIP is characteristically “V” shaped, the number of jets was increased to obtain total pressure distributions as required for gas turbine engine testing. With this understanding, a methodology has been developed to generate a target total pressure distortion pattern at the AIP. Turbulent flow computations are used to iteratively progress towards the target distribution. This methodology was demonstrated for a distortion flow pattern typical of use in gas turbine engine testing using twenty jets, which is a smaller number than reported in the literature. The procedure converges with a root-mean-square error of 3.836% and is able to reproduce the target pattern and other distortion parameters.

  12. Langley Atmospheric Information Retrieval System (LAIRS): System description and user's guide

    Science.gov (United States)

    Boland, D. E., Jr.; Lee, T.

    1982-01-01

    This document presents the user's guide, system description, and mathematical specifications for the Langley Atmospheric Information Retrieval System (LAIRS). It also includes a description of an optimal procedure for operational use of LAIRS. The primary objective of the LAIRS Program is to make it possible to obtain accurate estimates of atmospheric pressure, density, temperature, and winds along Shuttle reentry trajectories for use in postflight data reduction.

  13. DIDACTIC ENGINEERING: DESIGNING NEW GENERATION LEARNING SYSTEMS

    Directory of Open Access Journals (Sweden)

    Nail K. Nuriyev

    2016-09-01

    Full Text Available Introduction: the article deals with the organisation of training activities in the man-made environment. Didactic engineering is seen as a methodology within which problems of didactics are solved with application of pedagogical, psychological, engineering methods. It is obvious that in order to implement the training of future engineers in a competence-based format (according to educational standard a new type of teaching system is needed, with new capacities (properties. These systems should set each student towards the development of professionally significant (key abilities, taking into account his/her psychological characteristics; ensure training on the verge of permissible difficulties (developing training, and thereby achieve rapid development of key skills, through his/her zone of “immediate development”; to diagnose the quality of possession of a competence in the academic sense. For the objectivity and reliability of assessment of the level and depth of learned knowledge it is necessary to generate this evaluation in a metric format. As a result, we created a didactic system, which combines all the listed properties and the properties of classical systems. This allowed us to construct a new generation of didactic systems. Materials and Methods: the research is based on a systematic analysis of the activity of an engineer; on models of “zones of immediate development” by L. S. Vygotsky; on “developmental education” by L. N. Zankova; on the use of pedagogical and psychological patterns as well as taxonomic methods, didactic engineering, theory of probability and mathematical statistics. Results: constructed is a model for training engineers in the metric format of competence, which envisages a rapid development of students project and constructive abilit ies based on their knowledge learned. Discussion and Conclusions: the parameters defining the probability of engineer’s success have been described; the taxonomic scale

  14. The Pilatus unmanned aircraft system for lower atmospheric research

    Science.gov (United States)

    de Boer, Gijs; Palo, Scott; Argrow, Brian; LoDolce, Gabriel; Mack, James; Gao, Ru-Shan; Telg, Hagen; Trussel, Cameron; Fromm, Joshua; Long, Charles N.; Bland, Geoff; Maslanik, James; Schmid, Beat; Hock, Terry

    2016-04-01

    This paper presents details of the University of Colorado (CU) "Pilatus" unmanned research aircraft, assembled to provide measurements of aerosols, radiation and thermodynamics in the lower troposphere. This aircraft has a wingspan of 3.2 m and a maximum take-off weight of 25 kg, and it is powered by an electric motor to reduce engine exhaust and concerns about carburetor icing. It carries instrumentation to make measurements of broadband up- and downwelling shortwave and longwave radiation, aerosol particle size distribution, atmospheric temperature, relative humidity and pressure and to collect video of flights for subsequent analysis of atmospheric conditions during flight. In order to make the shortwave radiation measurements, care was taken to carefully position a high-quality compact inertial measurement unit (IMU) and characterize the attitude of the aircraft and its orientation to the upward-looking radiation sensor. Using measurements from both of these sensors, a correction is applied to the raw radiometer measurements to correct for aircraft attitude and sensor tilt relative to the sun. The data acquisition system was designed from scratch based on a set of key driving requirements to accommodate the variety of sensors deployed. Initial test flights completed in Colorado provide promising results with measurements from the radiation sensors agreeing with those from a nearby surface site. Additionally, estimates of surface albedo from onboard sensors were consistent with local surface conditions, including melting snow and bright runway surface. Aerosol size distributions collected are internally consistent and have previously been shown to agree well with larger, surface-based instrumentation. Finally the atmospheric state measurements evolve as expected, with the near-surface atmosphere warming over time as the day goes on, and the atmospheric relative humidity decreasing with increased temperature. No directional bias on measured temperature, as might

  15. The pilatus unmanned aircraft system for lower atmospheric research

    Directory of Open Access Journals (Sweden)

    G. de Boer

    2015-11-01

    Full Text Available This paper presents details of the University of Colorado (CU Pilatus unmanned research aircraft, assembled to provide measurements of aerosols, radiation and thermodynamics in the lower troposphere. This aircraft has a wingspan of 3.2 m and a maximum take off weight of 25 kg and is powered by an electric motor to reduce engine exhaust and concerns about carburetor icing. It carries instrumentation to make measurements of broadband up- and downwelling shortwave and longwave radiation, aerosol particle size distribution, atmospheric temperature, relative humidity and pressure and to collect video of flights for subsequent analysis of atmospheric conditions during flight. In order to make the shortwave radiation measurements, care was taken to carefully position a high-quality compact inertial measurement unit (IMU and characterize the attitude of the aircraft and it's orientation to the upward looking radiation sensor. Using measurements from both of these sensors, a correction is applied to the raw radiometer measurements to correct for aircraft attitude and sensor tilt relative to the sun. The data acquisition system was designed from scratch based on a set of key driving requirements to accommodate the variety of sensors deployed. Initial test flights completed in Colorado provide promising results with measurements from the radiation sensors agreeing with those from a nearby surface site. Additionally, estimates of surface albedo from onboard sensors were consistent with local surface conditions, including melting snow and bright runway surface. Aerosol size distributions collected are internally consistent and have previously been shown to agree well with larger, surface-based instrumentation. Finally the atmospheric state measurements evolve as expected, with the near-surface atmosphere warming over time as the day goes on, and the atmospheric relative humidity decreasing with increased temperature. No directional bias on measured

  16. Modeling and Simulation of Generator Side Converter of Doubly Fed Induction Generator-Based Wind Power Generation System

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Blaabjerg, Frede

    2010-01-01

    A real wind power generation system is given in this paper. SVM control strategy and vector control is applied for generator side converter and doubly fed induction generator respectively. First the mathematical models of the wind turbine rotor, drive train, generator side converter are described...

  17. Characteristics of a long and stable filamentary argon plasma jet generated in ambient atmosphere

    Science.gov (United States)

    Teodorescu, M.; Bazavan, M.; Ionita, E. R.; Dinescu, G.

    2015-04-01

    We present a study of a long (up to 60 mm) and thin (600 μm) plasma jet generated at 13.56 MHz in argon expanding in an open atmosphere from inside of a thin glass tube. The discharge is operated with one annular external electrode on the tube, in the absence of any grounded electrode in the discharge proximity. The study comprises image, spectral and electrical measurements, aiming to define and understand the operating domains of this plasma jet source. Two plasma zones were identified, which coexist: a long filament accompanied by a diffuse discharge. The coexistence of these plasma zones was studied in the power-mass flow rate parameter space. An electric model is proposed, considering the jet as a radiating antenna, which allows the determination of the main electrical parameters like capacitance, resistance and active RF power dissipated in the discharge. The specific zones on the I-V characteristics were assigned to the operating domains observed visually. The spectral emission of plasma has been used to characterize the jet in respect to the gas temperature, excitation temperature and plasma density.

  18. Fly in Atmosphere by Drag Force - Easy Thrust Generation Aircraft Engine Based Physics

    Science.gov (United States)

    Pierre Celestin, Mwizerwa

    2013-11-01

    This paper aims to present to the science community another way to fly in atmosphere, a way which is much more cheaper, efficient, safe and easy. Over the years scientists have been trying to find a way to built the vertically taking off vehicles but there have been no satisfactory success(what have been found was very expensive), Even aircrafts we know now need very sophisticated and expensive engines and not efficient enough. This way of flying may help our governments to spend less money on technologies and will help people to travel at very low prices so that, it may be a solution to the crisis which the world faces nowadays. In other words, it is my proposal to the next generation technologies we was looking for for years because everything can fly from the car to the trucks, the spaceships and even the hotels maybe constructed and fly as we construct the ships which sail in the oceans. My way of flying will have many applications in all the aspect of travel as it is going to be explained.

  19. Analysis of electrode system for generation of high-power electrodynamic flow

    Science.gov (United States)

    Rebrov, I. E.; Khomich, V. Yu.; Yamshchikov, V. A.

    2016-08-01

    A high-power electrodynamic flow in atmospheric air is numerically simulated and experimentally studied. An electrode system consisting of a cylindrical plasma emitter and a plane metal grid collector of ions is used to generate a flow with a speed of 2 m/s and a volume rate of 15 L/s.

  20. Observation of wave generation and non-local perturbations in the atmosphere during the passage of a typhoon

    Indian Academy of Sciences (India)

    V K Anandan; V N Sureshbabu; C J Pan; S Vijayabhaskara Rao

    2013-06-01

    During the passage of typhoon Kujira in April 2003 near to the northeast of Taiwan, atmospheric radar at Chung-Li (24° 58′N, 121° 11′E) was continuously operated. The data collected from profiler radar was used to investigate the impact of typhoon on generating waves and other atmospheric disturbances. Result showed that the typhoon and the associated wind disturbances can generate atmospheric waves with varied periodicity even when the core was far away from the land. The waves were quite prominent when the core was closer to the mountain. Observations show that these waves propagate vertically upward for many kilometers and getting trapped in higher altitudes. The radar reflectivity at the tropopause during the event showed that stable layer structure was very weak. Further, the enhancement in ozone measurement at the ground level was observed when the typhoon was near to radar site.

  1. Pre/post-strike atmospheric assessment system (PAAS)

    Energy Technology Data Exchange (ETDEWEB)

    Peglow, S. G., LLNL; Molitoris, J. D., LLNL

    1997-02-03

    The Pre/Post-Strike Atmospheric Assessment System was proposed to show the importance of local meteorological conditions in the vicinity of a site suspected of storing or producing toxic agents and demonstrate a technology to measure these conditions, specifically wind fields. The ability to predict the collateral effects resulting from an attack on a facility containing hazardous materials is crucial to conducting effective military operations. Our study approach utilized a combination of field measurements with dispersion modeling to better understand which variables in terrain and weather were most important to collateral damage predictions. To develop the PAAS wind-sensing technology, we utilized a combination of emergent and available technology from micro-Doppler and highly coherent laser systems. The method used for wind sensing is to probe the atmosphere with a highly coherent laser beam. As the beam probes, light is back-scattered from particles entrained in the air to the lidar transceiver and detected by the instrument. Any motion of the aerosols with a component along the beam axis leads to a Doppler shift of the received light. Scanning in a conical fashion about the zenith results in a more accurate and two-dimensional measurement of the wind velocity. The major milestones in the benchtop system development were to verify the design by demonstrating the technique in the laboratory, then scale the design down to a size consistent with a demonstrator unit which could be built to take data in the field. The micro-Doppler heterodyne system we developed determines absolute motion by optically mixing a reference beam with the return signal and has shown motion sensitivity to better than 1 cm/s. This report describes the rationale, technical approach and laboratory testing undertaken to demonstrate the feasibility and utility of a system to provide local meteorological data and predict atmospheric particulate motion. The work described herein was funded by

  2. Multi-protocol header generation system

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, David A.; Ignatowski, Michael; Jayasena, Nuwan; Loh, Gabriel

    2017-09-05

    A communication device includes a data source that generates data for transmission over a bus, and a data encoder that receives and encodes outgoing data. An encoder system receives outgoing data from a data source and stores the outgoing data in a first queue. An encoder encodes outgoing data with a header type that is based upon a header type indication from a controller and stores the encoded data that may be a packet or a data word with at least one layered header in a second queue for transmission. The device is configured to receive at a payload extractor, a packet protocol change command from the controller and to remove the encoded data and to re-encode the data to create a re-encoded data packet and placing the re-encoded data packet in the second queue for transmission.

  3. Apparatuses And Systems For Embedded Thermoelectric Generators

    KAUST Repository

    Hussain, Muhammad M.

    2013-08-08

    An apparatus and a system for embedded thermoelectric generators are disclosed. In one embodiment, the apparatus is embedded in an interface where the ambient temperatures on two sides of the interface are different. In one embodiment, the apparatus is fabricated with the interface in integrity as a unitary piece. In one embodiment, the apparatus includes a first thermoelectric material embedded through the interface. The apparatus further includes a second thermoelectric material embedded through the interface. The first thermoelectric material is electrically coupled to the second thermoelectric material. In one embodiment, the apparatus further includes an output structure coupled to the first thermoelectric material and the second thermoelectric material and configured to output a voltage.

  4. Atmospheric plasma generates oxygen atoms as oxidizing species in aqueous solutions

    Science.gov (United States)

    Mokhtar Hefny, Mohamed; Pattyn, Cedric; Lukes, Petr; Benedikt, Jan

    2016-10-01

    A remote microscale atmospheric pressure plasma jet (µAPPJ) with He, He/H2O, He/O2, and He/O2/H2O gas mixtures was used to study the transport of reactive species from the gas phase into the liquid and the following aqueous phase chemistry. The effects induced by the µAPPJ in water were quantitatively studied using phenol as a chemical probe and by measuring H2O2 concentration and pH values. These results were combined with the analysis of the absolute densities of the reactive species and the modeling of convective/diffusion transport and recombination reactions in the effluent of the plasma jet. Additionally, modified plasma jets were used to show that the role of emitted photons in aqueous chemistry is negligible for these plasma sources. The fastest phenol degradation was measured for the He/O2 plasma, followed by He/H2O, He/O2/H2O, and He plasmas. The modeled quantitative flux of O atoms into the liquid in the He/O2 plasma case was highly comparable with the phenol degradation rate and showed a very high transfer efficiency of reactive species from the plasma into the liquid, where more than half of the O atoms leaving the jet nozzle entered the liquid. The results indicate that the high oxidative effect of He/O2 plasma was primarily due to solvated O atoms, whereas OH radicals dominated the oxidative effects induced in water by plasmas with other gas mixtures. These findings help to understand, in a quantitative way, the complex interaction of cold atmospheric plasmas with aqueous solutions and will allow a better understanding of the interaction of these plasmas with water or buffered solutions containing biological macromolecules, microorganisms, or even eukaryotic cells. Additionally, the µAPPJ He/O2 plasma source seems to be an ideal tool for the generation of O atoms in aqueous solutions for any future studies of their reactivity.

  5. A New Generation of Micro Satellite Radiometers for Atmospheric Remote Sensing

    Science.gov (United States)

    He, jieying

    2017-04-01

    The need for low-cost, mission-flexible, and rapidly deployable space borne sensors that meet stringent performance requirements pervades the extreme weather monitoring programs, including especially the strong rainfall and typhoon. New technologies have enabled a novel approach toward this science observational goal, and in this paper we describe recent technology develop efforts to address the challenges above through the use of radiometers on a Micro-sized Microwave Atmospheric Satellite (Microsat), which operates in the type of constellation, and enable the capabilities of rapidly progressing. Recent work has involved the design and development of highly integrated radiometer component technologies that would enable the realization of a high-performance, multi-band sounder that would conform to the 3U CubeSat size (10 x 10 x 30 cm), weight, and power requirements. This paper partly focuses on the constellation to realize a scalable CubeSat-based system that will pave the path towards improved revisit rates over critical earth regions, and achieve state-of-the-art performance relative to current systems with respect to spatial, spectral, and radiometric resolution. As one of the important payloads on the platform, sub-millimeter radiometer is advised to house for providing atmospheric and oceanographic information all weather and all day. The first portion of the radiometer comprises a horn-fed reflector antenna, with a full-width at half-maximum (FWHM) beamwidth of 1.2°. Hence, the scanned beam has an approximate footprint diameter of 9.6 km at nadir incidence from a nominal altitude of 500 km. The antenna system is designed for a minimum 95% beam efficiency. Approximately 98 pixels are sampled for every scanning line, which covers a range of 1500km. The period of a round is about 94.47 minutes and re-visit period is four days. For the radiometer, which is a passive cross-track-scanning microwave spectrometer operating near the 118.75-GHz oxygen absorption

  6. Pluto-Charon system - the escape of Charon's primordial atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Trafton, L.; Stern, S.A.; Gladstone, G.R.

    1988-04-01

    Although Charon seems to have lost its atmosphere and surface volatiles, a lack of heating that would be sufficient to generate melting and consequent separation of the lighter and heavier nonvolatiles has probably resulted in the outer layers' retention of the primordial mix of nonvolatiles. Spectroscopically-determined relative abundances for the Charon surface should accordingly be representative of its entire mass, and thereby constitutes the basis of an understanding of Charon's origin. The study of Charon's exposed nonvolatile ices may ascertain whether the Pluto-Charon system condensed out of the solar nebula directly or from a protoplanetary nebula. 46 references.

  7. System and Method for Providing Vertical Profile Measurements of Atmospheric Gases

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A system and method for using an air collection device to collect a continuous air sample as the device descends through the atmosphere are provided. The air...

  8. Fleet Numerical Meteorology and Oceanography Center (FNMOC) Navy Operational Global Atmospheric Prediction System (NOGAPS)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Navy Operational Global Atmospheric Prediction System (NOGAPS) provides numerical guidance and products in support of a wide range of Navy oceanographic and...

  9. Report on technological development of fuel cell power generation 1998. Research and development on polymer electrolyte fuel cell (technological development of generating system, development of atmospheric operation home power system of several kW class); 1998 nendo seika hokokusho. Nenryo denchi hatsuden gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, joatsu sadogata su kW kyu kateiyo dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper explains the results of the research and development of polymer electrolyte fuel cells in fiscal 1998. For the purpose of developing a power source suitable for household use, a cell unit was developed in which performance was improved by reducing the thickness of a catalyst layer and increasing its ion-exchange capacity in the fuel cell body. There were prospects that low cost carbon materials and resin materials were usable in a carbon/resin composite plate. In the fuel supply technology, a serial two step type remover was developed concerning CO in a fuel using a selective oxidation process, which confirmed that the exit concentration was reducible to 10ppm or below even under a low S/C condition. With a reform ratio of 95% achieved with a 1kW class natural gas reformer, a thermal efficiency of 85% was attained by efficiently using combustion exhaust gas/reform gas sensible heat. In order to achieve a power generating efficiency of 35%, it is essential to improve reformer heat efficiency and cell performance, and also to produce steam for reforming by effectively utilizing reform gas/burner exhaust gas. The 1kW class module was verified in its stable operation and performance. (NEDO)

  10. Fuel cell power generation system. Nenryo denchi hatsuden system

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M.; Shiba, Y.

    1993-06-11

    It is general to fabricate the primary cooling water system including the fuel cell main body using corrosion resistant stainless steel, while the secondary cooling system including absorption type freezer is made of carbon steel. For this structure, returning the cooling water of the secondary cooling system to the primary cooling system can cause the corrosion of the primary cooling system. That is, the water of inferior quality in the secondary system can corrode the primary system including the fuel cell. This invention solves the problem. The fuel cell bypass which is branched from the fuel cell cooling water inlet, detours the fuel cell, and it is connected to the water-vapor separator installed to the fuel cell. And the heat exchanger is installed at any of fuel cooling water outlet line, fuel cell cooling water inlet line, or fuel cell bypass line. With this structure, recovering the heat generated during the power generation by the fuel cell at the secondary side of the heat exchanger can be achieved while separating the primary and secondary cooling water. So that the trouble of fuel cell operation caused by the contamination of the primary cooling water with the secondary cooling water which contains corrosive impurities can be avoided. 6 figs.

  11. Particle Densities of the Atmospheric-Pressure Argon Plasmas Generated by the Pulsed Dielectric Barrier Discharges

    Science.gov (United States)

    Pan, Jie; Li, Li; Wang, Yunuan; Xiu, Xianwu; Wang, Chao; Song, Yuzhi

    2016-11-01

    Atmospheric-pressure argon plasmas have received increasing attention due to their high potential in many industrial and biomedical applications. In this paper, a 1-D fluid model is used for studying the particle density characteristics of the argon plasmas generated by the pulsed dielectric barrier discharges. The temporal evolutions of the axial particle density distributions are illustrated, and the influences of changing the main discharge conditions on the averaged particle densities are researched by independently varying the various discharge conditions. The calculation results show that the electron density and the ion density reach two peaks near the momentary cathodes during the rising and the falling edges of the pulsed voltage. Compared with the charged particle densities, the densities of the resonance state atom Arr and the metastable state atom Arm have more uniform axial distributions, reach higher maximums and decay more slowly. During the platform of the pulsed voltage and the time interval between the pulses, the densities of the excited state atom Ar* are far lower than those of the Arr or the Arm. The averaged particle densities of the different considered particles increase with the increases of the amplitude and the frequency of the pulsed voltage. Narrowing the discharge gap and increasing the relative dielectric constant of the dielectric also contribute to the increase of the averaged particle densities. The effects of reducing the discharge gap distance on the neutral particle densities are more significant than the influences on the charged particle densities. supported by Natural Science Foundation of Shandong Province, China (No. ZR2015AQ008), and Project of Shandong Province Higher Educational Science and Technology Program of China (No. J15LJ04)

  12. Application of lightning discharge generated radio atmospherics/tweeks in lower ionospheric plasma diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    Maurya, A K; Singh, R; Veenadhari, B [Indian Institute of Geomagnetism, New Panvel, Navi Mumbai - 410 218 (India); Pant, P [Aryabhatta Research Institute of Observational Sciences (ARIES), Manora Peak, Nainital - 263129, Uttrakhand (India); Singh, A K, E-mail: ajeet.iig@gmail.co, E-mail: akmaurya@iigs.iigm.res.i [Physics Department, Banaras Hindu University, Varanasi - 221005 (India)

    2010-02-01

    Lightning discharges during thunderstorm are the significant natural source of electromagnetic waves. They generate electromagnetic pulses, which vary from few Hz to tens of MHz, but the maximum radiated energy is confined in extremely low (ELF: 3-3000Hz) and very low (VLF: 3-30 KHz) frequency band. These pulsed signals with frequency dispersion are known as radio atmospherics or tweeks. These waves propagate through the process of multiple reflections in the earth-ionosphere waveguide over long distances with very low attenuation (2-3 dB/1000km). Since these waves are reflected by lower boundary of ionosphere, these are used extensively for probing the D-region ionosphere. D-region is important to the space weather, as well as the submarine communication and navigational aid. In this perspective the measurement of electron density profiles of the D-region is undoubtedly of great interest to both the development of reliable models and radio wave propagation. Earlier work on the tweeks is mainly focused to the theoretical considerations related to polarization, waveform analysis, and occurrence time and propagation mechanism. In this study we investigate tweeks to determine the equivalent night time electron densities at reflection height of the D-region. Distance traveled by the VLF waves from the causative lightning discharges to the receiving station has also been calculated. Tweeks recorded at a low latitude ground station of Allahabad (Geomag. lat. 16.05{sup 0} N) during the night of 23 March 2007 have been used in the present analysis. Based on the analysis of the fundamental cut-off frequency of tweeks, the estimated equivalent electron density of the D-region has been found to be in the range of {approx}20 to 25 el/cm{sup 3} at ionospheric reflection height of {approx}80 to 95 km respectively. Propagation distance in Earth-Ionosphere wave guide (EIWG) from causative lightning source to experimental site varies from {approx}1500 to 8000 km.

  13. GENERATION OF MAGNETOHYDRODYNAMIC WAVES IN LOW SOLAR ATMOSPHERIC FLUX TUBES BY PHOTOSPHERIC MOTIONS

    Energy Technology Data Exchange (ETDEWEB)

    Mumford, S. J.; Fedun, V.; Erdélyi, R., E-mail: s.mumford@sheffield.ac.uk [Solar Physics and Space Plasma Research Centre (SP2RC), School of Mathematics and Statistics, The University of Sheffield, Hicks Building, Hounsfield Road, Sheffield S3 7RH UK (United Kingdom)

    2015-01-20

    Recent ground- and space-based observations reveal the presence of small-scale motions between convection cells in the solar photosphere. In these regions, small-scale magnetic flux tubes are generated via the interaction of granulation motion and the background magnetic field. This paper studies the effects of these motions on magnetohydrodynamic (MHD) wave excitation from broadband photospheric drivers. Numerical experiments of linear MHD wave propagation in a magnetic flux tube embedded in a realistic gravitationally stratified solar atmosphere between the photosphere and the low choromosphere (above β = 1) are performed. Horizontal and vertical velocity field drivers mimic granular buffeting and solar global oscillations. A uniform torsional driver as well as Archimedean and logarithmic spiral drivers mimic observed torsional motions in the solar photosphere. The results are analyzed using a novel method for extracting the parallel, perpendicular, and azimuthal components of the perturbations, which caters to both the linear and non-linear cases. Employing this method yields the identification of the wave modes excited in the numerical simulations and enables a comparison of excited modes via velocity perturbations and wave energy flux. The wave energy flux distribution is calculated to enable the quantification of the relative strengths of excited modes. The torsional drivers primarily excite Alfvén modes (≈60% of the total flux) with small contributions from the slow kink mode, and, for the logarithmic spiral driver, small amounts of slow sausage mode. The horizontal and vertical drivers primarily excite slow kink or fast sausage modes, respectively, with small variations dependent upon flux surface radius.

  14. Simulation of Aircraft Sortie Generation Under an Autonomic Logistics System

    Science.gov (United States)

    2016-12-01

    SIMULATION OF AIRCRAFT SORTIE GENERATION UNDER AN AUTONOMIC LOGISTICS SYSTEM THESIS Gunduz...Government. AFIT-ENS-MS-16-D-052 SIMULATION OF AIRCRAFT SORTIE GENERATION UNDER AN AUTONOMIC LOGISTICS SYSTEM THESIS Presented to...DISTRIBUTION UNLIMITED. AFIT-ENS-MS-16-D-052 SIMULATION OF AIRCRAFT SORTIE GENERATION UNDER AN AUTONOMIC LOGISTICS SYSTEM THESIS

  15. Technical notes for the conceptual design for an atmospheric fluidized-bed direct combustion power generating plant. [Comparison of AFB plant and pulverized coal plant

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-04-01

    The first part of this report presents a comparison of the conceptual designs of a large (570 MW(e)) pulverized coal (PC) steam generator equipped with a wet limestone flue gas desulfurization (FGD) system and two equivalent sized atmospheric fluidized bed (AFB) steam generators including balance of plants for electric-power generation. The reader is cautioned that this portion of the report compares a zero generation AFB technology to pulverized coal technology which has been operationally and economically optimized for the past half-century. This comparison is intended to be indicative of whether further development of the AFB concept as a viable alternative to the PC/FGD concept for electric-power generation is merited. In the second part, the load-following capability of a once-through subcritical atmospheric fluidized bed boiler is analyzed. Digital computer simulation predictions of the plant's response to open loop step changes in firing rate, feedwater flow, governor valve, unit load demand, etc, are made. The predicted response of throttle pressure, steam temperature, unit load, etc, are compared to the response of a conventional coal-fired, once-through, subcritical unit. The load-following capability is assessed through this qualitative comparison. Additional model response predictions are also presented for which no test data are presently available.

  16. The 400-Hertz constant-speed electrical generation systems

    Science.gov (United States)

    Mcclung, R.

    1982-01-01

    Materials illustrating a presentation on 400 Hz constant speed generation systems are presented. The system features are outlined, components and functioning described, and display graphics illustrated.

  17. Environmental Control and Life Support System, Oxygen Generation System

    Science.gov (United States)

    2000-01-01

    The Environmental Control and Life Support System (ECLSS) Group of the Flight Projects Directorate at the Marshall Space Flight Center (MSFC) in Huntsville, Alabama, is responsible for designing and building the life support systems that will provide the crew of the International Space Station (ISS) a comfortable environment in which to live and work. This is a close-up view of ECLSS Oxygen Generation System (OGS) rack. The ECLSS Group at the MSFC oversees the development of the OGS, which produces oxygen for breathing air for the crew and laboratory animals, as well as for replacing oxygen lost due to experiment use, airlock depressurization, module leakage, and carbon dioxide venting. The OGS consists primarily of the Oxygen Generator Assembly (OGA), provided by the prime contractor, the Hamilton Sundstrand Space Systems, International (HSSSI) in Windsor Locks, Cornecticut and a Power Supply Module (PSM), supplied by the MSFC. The OGA is comprised of a cell stack that electrolyzes (breaks apart the hydrogen and oxygen molecules) some of the clean water provided by the Water Recovery System and the separators that remove the gases from water after electrolysis. The PSM provides the high power to the OGA needed to electrolyze the water.

  18. NEXT GENERATION GAS TURBINE (NGGT) SYSTEMS STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2001-12-05

    to how they could serve multiple applications, both in terms of incorporation of technology into current products, as well as to an NGGT product. In summary, potential program costs are shown for development of the candidate systems along with the importance of future DOE enabling participation. Three main conclusions have been established via this study: (1) Rapid recent changes within the power generation regulatory environment and the resulting ''bubble'' of gas turbine orders has altered the timing and relative significance associated with the conclusions of the ADL study upon which the original DOE NGGT solicitation was based. (2) Assuming that the relevant technologies were developed and available for an NGGT market opportunity circa 2010, the top candidate system that meets or exceeds the DOE PRDA requirements was determined to be a hybrid aero-derivative/heavy duty concept. (3) An investment by DOE of approximately $23MM/year to develop NGGT technologies near/mid term for validation and migration into a reasonable fraction of the installed base of GE F-class products could be leveraged into $1.2B Public Benefit, with greatest benefits resulting from RAM improvements. In addition to the monetary Public Benefit, there is also significant benefit in terms of reduced energy consumption, and reduced power plant land usage.

  19. The Probabilistic Model of Keys Generation of QKD Systems

    CERN Document Server

    Golubchikov, Dmitry

    2010-01-01

    The probabilistic model of keys generation of QKD systems is proposed. The model includes all phases of keys generation starting from photons generation to states detection taking characteristics of fiber-optics components into account. The paper describes the tree of events of QKD systems. Equations are found for estimation of the effectiveness of the process of sifted keys generation as well as for bit-error probability and for the rate of private keys generation.

  20. Planetary Atmospheric Electricity

    CERN Document Server

    Leblanc, F; Yair, Y; Harrison, R. G; Lebreton, J. P; Blanc, M

    2008-01-01

    This volume presents our contemporary understanding of atmospheric electricity at Earth and in other solar system atmospheres. It is written by experts in terrestrial atmospheric electricity and planetary scientists. Many of the key issues related to planetary atmospheric electricity are discussed. The physics presented in this book includes ionisation processes in planetary atmospheres, charge generation and separation, and a discussion of electromagnetic signatures of atmospheric discharges. The measurement of thunderstorms and lightning, including its effects and hazards, is highlighted by articles on ground and space based instrumentation, and new missions.Theory and modelling of planetary atmospheric electricity complete this review of the research that is undertaken in this exciting field of space science. This book is an essential research tool for space scientists and geoscientists interested in electrical effects in atmospheres and planetary systems. Graduate students and researchers who are new to t...

  1. Chemically reactive species in liquids generated by atmospheric-pressure plasmas and their roles in plasma medicine

    Energy Technology Data Exchange (ETDEWEB)

    Hamaguchi, Satoshi [Center for Atomic and Molecular Technologies, Graduate School of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan)

    2013-07-11

    Plasmas whose gas temperatures are close to room temperature may be generated in ambient air or a gas at atmospheric pressure with the use of low-frequency high voltage or low-power radio-frequency (RF) or microwave power applied to electrodes. Such plasmas can serve as a powerful source of free radicals and/or chemically reactive species that arise from atoms and molecules of the ambient gas. Recently use of such plasmas for medical purposes has attracted much attention as they can be implemented in possible medical devices that can cause blood coagulation, heal wounds, facilitate angiogenesis, sterilize surgical devices as well as living tissues without harming healthy cells, and selectively inactivate cancer cells. Especially of interest among reactive species generated by atmospheric-pressure plasmas (APP) are reactive oxygen species (ROS) and reactive nitrogen species (RNS) that are generated in liquid phase. Since most living tissues and cells are immersed in liquids (such as blood or culture media), reactive species generated by APPs in the gas phase are transported to the liquid phase and possibly converted to different types of reactive species therein before causing some influence on the tissues or cells. In this study, the rate equations are solved to evaluate concentrations of various reactive species in pure water that are originated by plasma reactions in atmosphere and possible effects of such species (including ROS/RNS) on living tissues and cells are discussed.

  2. The System of the Calibration for Visibility Measurement Instrument Under the Atmospheric Aerosol Simulation Environment

    Directory of Open Access Journals (Sweden)

    Shu Zhifeng

    2016-01-01

    formula, then it been divided by 3 is MOR. The aerosol concentration in chamber can be changed by adjusting aerosol generator that producing variety of visibility atmospherical environment. The experiment has been carried out and the measurement accuracy of atmospheric transmittance is 0.3‰ Corresponding to the accuracy of MOR 4.9% at the 2km visibility environment. So this system can be calibrated and validated the other visibility measuring devices.

  3. Atmospheric pressure loading effects on Global Positioning System coordinate determinations

    Science.gov (United States)

    Vandam, Tonie M.; Blewitt, Geoffrey; Heflin, Michael B.

    1994-01-01

    Earth deformation signals caused by atmospheric pressure loading are detected in vertical position estimates at Global Positioning System (GPS) stations. Surface displacements due to changes in atmospheric pressure account for up to 24% of the total variance in the GPS height estimates. The detected loading signals are larger at higher latitudes where pressure variations are greatest; the largest effect is observed at Fairbanks, Alaska (latitude 65 deg), with a signal root mean square (RMS) of 5 mm. Out of 19 continuously operating GPS sites (with a mean of 281 daily solutions per site), 18 show a positive correlation between the GPS vertical estimates and the modeled loading displacements. Accounting for loading reduces the variance of the vertical station positions on 12 of the 19 sites investigated. Removing the modeled pressure loading from GPS determinations of baseline length for baselines longer than 6000 km reduces the variance on 73 of the 117 baselines investigated. The slight increase in variance for some of the sites and baselines is consistent with expected statistical fluctuations. The results from most stations are consistent with approximately 65% of the modeled pressure load being found in the GPS vertical position measurements. Removing an annual signal from both the measured heights and the modeled load time series leaves this value unchanged. The source of the remaining discrepancy between the modeled and observed loading signal may be the result of (1) anisotropic effects in the Earth's loading response, (2) errors in GPS estimates of tropospheric delay, (3) errors in the surface pressure data, or (4) annual signals in the time series of loading and station heights. In addition, we find that using site dependent coefficients, determined by fitting local pressure to the modeled radial displacements, reduces the variance of the measured station heights as well as or better than using the global convolution sum.

  4. Scaling laws of diffusion and time intermittency generated by coherent structures in atmospheric turbulence

    Science.gov (United States)

    Paradisi, P.; Cesari, R.; Donateo, A.; Contini, D.; Allegrini, P.

    2012-02-01

    We investigate the time intermittency of turbulent transport associated with the birth-death of self-organized coherent structures in the atmospheric boundary layer. We apply a threshold analysis on the increments of turbulent fluctuations to extract sequences of rapid acceleration events, which is a marker of the transition between self-organized structures. The inter-event time distributions show a power-law decay ψ(τ) ~ 1/τμ, with a strong dependence of the power-law index μ on the threshold. A recently developed method based on the application of event-driven walking rules to generate different diffusion processes is applied to the experimental event sequences. At variance with the power-law index μ estimated from the inter-event time distributions, the diffusion scaling H, defined by ⟨ X2⟩ ~ t2H, is independent from the threshold. From the analysis of the diffusion scaling it can also be inferred the presence of different kind of events, i.e. genuinely transition events and spurious events, which all contribute to the diffusion process but over different time scales. The great advantage of event-driven diffusion lies in the ability of separating different regimes of the scaling H. In fact, the greatest H, corresponding to the most anomalous diffusion process, emerges in the long time range, whereas the smallest H can be seen in the short time range if the time resolution of the data is sufficiently accurate. The estimated diffusion scaling is also robust under the change of the definition of turbulent fluctuations and, under the assumption of statistically independent events, it corresponds to a self-similar point process with a well-defined power-law index μD ~ 2.1, where D denotes that μD is derived from the diffusion scaling. We argue that this renewal point process can be associated to birth and death of coherent structures and to turbulent transport near the ground, where the contribution of turbulent coherent structures becomes dominant.

  5. Optical properties of the atmospheric pressure helium plasma jet generated by alternative current (a.c.) power supply

    Science.gov (United States)

    Ilik, Erkan; Akan, Tamer

    2016-05-01

    In this work, an atmospheric pressure plasma jet (APPJ) was produced to generate cold flowing post-discharge plasma of pure helium gas. The main aim of this study was to generate cold flowing APPJ of pure helium gas and to determine how their optical emission spectrum change influences varying different flow rates. Lengths of early, middle, and late post-discharge plasma (jet) regions and their fluctuations were determined, respectively. Then, ignition condition dependence of the post-discharge plasma for flow rate was specified at a constant voltage. Spectroscopic studies of an atmospheric pressure plasma jet of helium were presented via analyzing OH, N2, N2+, oxygen, and helium intensities for various flow rates.

  6. Development of a tiny tandem balloon system for atmospheric observation

    Science.gov (United States)

    Saito, Yoshitaka; Yamada, Kazuhiko; Fujiwara, Masatomo

    2016-07-01

    A tandem balloon system with a combination of a zero-pressure balloon on top and a super-pressure balloon on the bottom has a unique trajectory characteristic, with different flight altitudes between day and night and thus with ascending and descending motions at dawn and dusk, respectively. This characteristic provides a unique opportunity to explore the atmosphere, e.g., the upper tropospheric and lower stratospheric region with cross-tropopause measurements twice a day. We started development of a tiny tandem balloon system using a 10 m^{3} super-pressure balloon and a 100 m^{3} zero-pressure balloon, with a capability of carrying 3 kg of payload. One of the scientific targets is to measure water vapor, cloud particles, and temperature around the tropical tropopause which is the entry point of the stratospheric and mesospheric meridional circulation. For the data transfer, the iridium satellite communication module, SBD9603 is used. In this paper, the current status of the development will be reported.

  7. Power Maximization Control of Variable Speed Wind Generation System Using Permanent Magnet Synchronous Generator

    Science.gov (United States)

    Morimoto, Shigeo; Nakamura, Tomohiko; Takeda, Yoji

    This paper proposes the sensorless output power maximization control of the wind generation system. A permanent magnet synchronous generator (PMSG) is used as a variable speed generator in the proposed system. The generator torque is suitably controlled according to the generator speed and thus the power from a wind turbine settles down on the maximum power point by the proposed MPPT control method, where the information of wind velocity is not required. Moreover, the maximum available generated power is obtained by the optimum current vector control. The current vector of PMSG is optimally controlled according to the generator speed and the required torque in order to minimize the losses of PMSG considering the voltage and current constraints. The proposed wind power generation system can be achieved without mechanical sensors such as a wind velocity detector and a position sensor. Several experimental results show the effectiveness of the proposed control method.

  8. Experimental demonstration of next-generation FSO communication system

    Science.gov (United States)

    Kazaura, Kamugisha; Omae, Kazunori; Suzuki, Toshiji; Matsumoto, Mitsuji; Mutafungwa, Edward; Asatani, Koichi; Murakami, Tadaaki; Takahashi, Koichi; Matsumoto, Hideki; Wakamori, Kazuhiko; Arimoto, Yoshinori

    2006-10-01

    Free-space optical communication has emerged as a competitive and viable technology for offering high data rates, improved capacity, cost-effective and an easy to deploy solution for providing connectivity between two points which are up to a few kilometers apart. In this paper we present experimental work which demonstrates the practicality of next generation free-space optical (FSO) communication systems suitable for short-haul, high-speed and robust data links. This experimental system is placed between two buildings in the Waseda University campus area for a communication link spanning a distance of 1 km. We outline the design of the optical antenna which uses 1550 nm wavelength and directly coupling a freespace optical beam to a single-mode fiber without the need for OE/EO conversion, to offer a communication link with data rates from 2.5 Gbps to 10 Gbps. The antenna is capable of overcoming most common limitations inherent in FSO communication systems, such as atmospheric induced beam wander and scintillation effects. A high-speed tracking mechanism which utilizes a fine positioning mirror (FPM) capable of tracking and controlling the received beam and focusing/steering most of beam power into the fiber is presented. This FPM is capable of suppressing the frequent power fluctuations caused by beam angle-of-arrival (AOA) variations. This paper presents experimental results of the FSO communication system capable offering stable performance in terms of measured bit-error-rate (BER). Performance results showing increasing the systems data rate from 2.5 Gbps to 10 Gpbs are also presented.

  9. Cloud Effects on Meridional Atmospheric Energy Budget Estimated from Clouds and the Earth's Radiant Energy System (CERES) Data

    Science.gov (United States)

    Kato, Seiji; Rose, Fred G.; Rutan, David A.; Charlock, Thomas P.

    2008-01-01

    The zonal mean atmospheric cloud radiative effect, defined as the difference of the top-of-atmosphere (TOA) and surface cloud radiative effects, is estimated from three years of Clouds and the Earth's Radiant Energy System (CERES) data. The zonal mean shortwave effect is small, though it tends to be positive (warming). This indicates that clouds increase shortwave absorption in the atmosphere, especially in midlatitudes. The zonal mean atmospheric cloud radiative effect is, however, dominated by the longwave effect. The zonal mean longwave effect is positive in the tropics and decreases with latitude to negative values (cooling) in polar regions. The meridional gradient of cloud effect between midlatitude and polar regions exists even when uncertainties in the cloud effect on the surface enthalpy flux and in the modeled irradiances are taken into account. This indicates that clouds increase the rate of generation of mean zonal available potential energy. Because the atmospheric cooling effect in polar regions is predominately caused by low level clouds, which tend to be stationary, we postulate that the meridional and vertical gradients of cloud effect increase the rate of meridional energy transport by dynamics in the atmosphere from midlatitude to polar region, especially in fall and winter. Clouds then warm the surface in polar regions except in the Arctic in summer. Clouds, therefore, contribute in increasing the rate of meridional energy transport from midlatitude to polar regions through the atmosphere.

  10. Local-Rapid Evaluation of Atmospheric Conditions (L-REAC (trademark)) System, Volume 4 (System Evaluation)

    Science.gov (United States)

    2011-12-01

    first responder s operational decision aid called the Local-Rapid Evaluation of Atmospheric Conditions (L-REAC ) System . As part of the technology transfer process, a detailed evaluation of the L-REAC System was conducted by volunteer and professional emergency first responders. This report documents the evaluation process, results and recommendations. In short, all evaluators independently stated that they would recommend the L-REAC System for

  11. Integration of Renewable Generation in Power System Defence Plans

    DEFF Research Database (Denmark)

    Das, Kaushik

    , one of them being the North East area with high share of wind power generation.The aim of this study is to investigate how renewable generations like wind power can contribute to the power system defence plans. This PhD project “Integration of Renewable Generation in Power System Defence Plans...

  12. Schedule Sales Query Report Generation System

    Data.gov (United States)

    General Services Administration — Schedule Sales Query presents sales volume figures as reported to GSA by contractors. The reports are generated as quarterly reports for the current year and the...

  13. Electrical power systems for distributed generation

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, T.A.; Huval, S.J. [Stewart & Stevenson Services, Inc., Houston, TX (United States)

    1996-12-31

    {open_quotes}Distributed Generation{close_quotes} has become the {open_quotes}buzz{close_quotes} word of an electric utility industry facing deregulation. Many industrial facilities utilize equipment in distributed installations to serve the needs of a thermal host through the capture of exhaust energy in a heat recovery steam generator. The electrical power generated is then sold as a {open_quotes}side benefit{close_quotes} to the cost-effective supply of high quality thermal energy. Distributed generation is desirable for many different reasons, each with unique characteristics of the product. Many years of experience in the distributed generation market has helped Stewart & Stevenson to define a range of product features that are crucial to most any application. The following paper will highlight a few of these applications. The paper will also examine the range of products currently available and in development. Finally, we will survey the additional services offered by Stewart & Stevenson to meet the needs of a rapidly changing power generation industry.

  14. Fractional-order Systems and Synchronous Generator Voltage Regulator

    Directory of Open Access Journals (Sweden)

    Wojciech Lubośny

    2015-03-01

    Full Text Available Modern regulators of synchronous generators, including voltage regulators, are digital systems, in their vast majority with standard structures contained in the IEEE standard. These are systems described with stationary differential equations of integral order. Differential equations of fractional order are not employed in regulators for synchronous generator control. This paper presents an analysis of the possibilities of using a system of fractional differential equations in the voltage regulator of an synchronous generator with a static excitation system.

  15. Integration of Renewable Generation in Power System Defence Plans

    OpenAIRE

    Das, Kaushik; Sørensen, Poul Ejnar; Anca Daniela HANSEN; Abildgaard, Hans

    2016-01-01

    Increasing levels of penetration of wind power and other renewable generations in European power systems pose challenges to power system security. The power system operators are continuously challenged especially when generations from renewables are high thereby reducing online capacity of conventional controllable generations to minimum. In such operation hours, the system is typically more vulnerable to disturbances in general and major disturbances in particular. This was the case in the m...

  16. Tau-REx I: A next generation retrieval code for exoplanetary atmospheres

    CERN Document Server

    Waldmann, Ingo P; Barton, Emma J; Yurchenko, Sergey N; Tennyson, Jonathan

    2014-01-01

    Spectroscopy of exoplanetary atmospheres has become a well established method for the characterisation of extrasolar planets. We here present a novel inverse retrieval code for exoplanetary atmospheres. Tau-REx (Tau Retrieval for Exoplanets) is a line-by-line radiative transfer fully Bayesian retrieval framework. It differentiates itself from existing codes in the literature through: 1) the optimised use of molecular line-lists from the ExoMol project; 2) an unbiased atmospheric composition prior selection, through custom built pattern recognition software; 3) the use of two independent algorithms to fully sample the Bayesian likelihood space: nested sampling as well as a more classical Markov Chain Monte Carlo approach; 4) iterative Bayesian parameter and model selection using the full Bayesian Evidence as well as the Savage-Dickey Ratio for nested models, and 5) the ability to fully map very large parameter spaces through optimal code parallelisation and scalability to cluster computing. In this publication...

  17. High Pressure Atmospheric Sampling Inlet System for Venus or the Gas Giants Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Thorleaf Research, Inc. proposes to develop a miniaturized high pressure atmospheric sampling inlet system for sample acquisition in extreme planetary environments,...

  18. Healthcare waste generation and its management system: the case ...

    African Journals Online (AJOL)

    Healthcare waste generation and its management system: the case of health ... in the course of activities, the generation of hazardous and non hazardous waste is a ... Segregation of wastes and pre treatment of infectious wastes were not ...

  19. A novel SOFC tri-generation system for building applications

    OpenAIRE

    Elmer, Theo

    2015-01-01

    In response to the critical need to decarbonise the built environment, alternative methods for more effective energy utilisation need to be explored including tri-generation systems. Tri-generation is the simultaneous generation of electricity, heating and/or cooling from a single fuel source. Solid oxide fuel cell (SOFC) and liquid desiccant demonstrate many characteristics that make them an attractive option in the development of an efficient and effective tri-generation system. SOFCs h...

  20. A Topological Trigger System for Imaging Atmospheric-Cherenkov Telescopes

    CERN Document Server

    Schroedter, M; Byrum, K; Drake, G; Duke, C; Holder, J; Imran, A; Madhavan, A; Krennrich, F; Kreps, A; Smith, A

    2009-01-01

    A fast trigger system is being designed as a potential upgrade to VERITAS, or as the basis for a future array of imaging atmospheric-Cherenkov telescopes such as AGIS. The scientific goal is a reduction of the energy threshold by a factor of 2 over the current threshold of VERITAS of around 130 GeV. The trigger is being designed to suppress both accidentals from the night-sky background and cosmic rays. The trigger uses field-programmable gate arrays (FPGAs) so that it is adaptable to different observing modes and special physics triggers, e.g. pulsars. The trigger consists of three levels: The level 1 (L1.5) trigger operating on each telescope camera samples the discriminated pixels at a rate of 400 MHz and searches for nearest-neighbor coincidences. In L1.5, the received discriminated signals are delay-compensated with an accuracy of 0.078 ns, facilitating a short coincidence time-window between any nearest neighbor of 5 ns. The hit pixels are then sent to a second trigger level (L2) that parameterizes the ...

  1. The development and application of a cold atmospheric plasma generator for treatment of skin and soft-tissue injuries in animals

    Science.gov (United States)

    Emelyanov, O. A.; Petrova, N. O.; Smirnova, N. V.; Shemet, M. V.

    2017-08-01

    We describe a device for obtaining cold plasma in air at atmospheric pressure using a system of positive high-voltage pin electrodes, which is intended for the treatment of skin and soft-tissue injuries in animals. Plasma is generated due to the development of periodic pulsed discharge of nanosecond duration at current pulse amplitudes 10-20 mA, characteristic frequencies 10-20 kHz, and applied voltages within 8-10 kV. The high efficacy of the proposed device and method is confirmed by the good clinical results of treating large domestic animals with traumatic injuries.

  2. The Selection of Cooling systems of Giant Hydro-Generators

    Institute of Scientific and Technical Information of China (English)

    Li Dingzhong

    2010-01-01

    @@ The selection of cooling system for hydro-generator in Ertan Hydropower Station is reviewed in this pap(ar) The new viewpoint on air-cooled system of hydraul(is)generator of recent years is analyzed and described. That is, "Full air-cooled system is always preferred to inner water cooling system in hydro-generator." Moreov() the decision process and corresponding actions of aircooled system design for hydro-generator in Longtan Hydropower Station, Xiaowan Hydropower Station and Laxiwa Hydropower Station are introduced.

  3. Water cycles in closed ecological systems: effects of atmospheric pressure

    Science.gov (United States)

    Rygalov, Vadim Y.; Fowler, Philip A.; Metz, Joannah M.; Wheeler, Raymond M.; Bucklin, Ray A.; Sager, J. C. (Principal Investigator)

    2002-01-01

    In bioregenerative life support systems that use plants to generate food and oxygen, the largest mass flux between the plants and their surrounding environment will be water. This water cycle is a consequence of the continuous change of state (evaporation-condensation) from liquid to gas through the process of transpiration and the need to transfer heat (cool) and dehumidify the plant growth chamber. Evapotranspiration rates for full plant canopies can range from 1 to 10 L m-2 d-1 (1 to 10 mm m-2 d-1), with the rates depending primarily on the vapor pressure deficit (VPD) between the leaves and the air inside the plant growth chamber. VPD in turn is dependent on the air temperature, leaf temperature, and current value of relative humidity (RH). Concepts for developing closed plant growth systems, such as greenhouses for Mars, have been discussed for many years and the feasibility of such systems will depend on the overall system costs and reliability. One approach for reducing system costs would be to reduce the operating pressure within the greenhouse to reduce structural mass and gas leakage. But managing plant growth environments at low pressures (e.g., controlling humidity and heat exchange) may be difficult, and the effects of low-pressure environments on plant growth and system water cycling need further study. We present experimental evidence to show that water saturation pressures in air under isothermal conditions are only slightly affected by total pressure, but the overall water flux from evaporating surfaces can increase as pressure decreases. Mathematical models describing these observations are presented, along with discussion of the importance for considering "water cycles" in closed bioregenerative life support systems.

  4. Synchronization System for Next Generation Light Sources

    Energy Technology Data Exchange (ETDEWEB)

    Zavriyev, Anton

    2014-03-27

    An alternative synchronization technique – one that would allow explicit control of the pulse train including its repetition rate and delay is clearly desired. We propose such a scheme. Our method is based on optical interferometry and permits synchronization of the pulse trains generated by two independent mode-locked lasers. As the next generation x-ray sources will be driven by a clock signal derived from a mode-locked optical source, our technique will provide a way to synchronize x-ray probe with the optical pump pulses.

  5. Interfacing the Urban Land-Atmosphere System Through Coupled Urban Canopy and Atmospheric Models

    Science.gov (United States)

    Song, Jiyun; Wang, Zhi-Hua

    2015-03-01

    We couple a single column model (SCM) to a cutting-edge single-layer urban canopy model (SLUCM) with realistic representation of urban hydrological processes. The land-surface transport of energy and moisture parametrized by the SLUCM provides lower boundary conditions to the overlying atmosphere. The coupled SLUCM-SCM model is tested against field measurements of sensible and latent heat fluxes in the surface layer, as well as vertical profiles of temperature and humidity in the mixed layer under convective conditions. The model is then used to simulate urban land-atmosphere interactions by changing urban geometry, surface albedo, vegetation fraction and aerodynamic roughness. Results show that changes of landscape characteristics have a significant impact on the growth of the boundary layer as well as on the distributions of temperature and humidity in the mixed layer. Overall, the proposed numerical framework provides a useful stand-alone modelling tool, with which the impact of urban land-surface conditions on the local hydrometeorology can be assessed via land-atmosphere interactions.

  6. Optimizing Hybrid Wind/Diesel Generator System Using BAT Algorithm

    Directory of Open Access Journals (Sweden)

    Sudhir Sharma,

    2016-01-01

    Full Text Available Hybrid system comprising of Wind/Diesel generation system for a practical standalone application considers Wind turbine generators and diesel generator as primary power sources for generating electricity. Battery banks are considered as a backup power source. The total value of cost is reduced by meeting energy demand required by the customers. Bat optimization technique is implemented to optimize wind and battery modules. Wind and battery banks are considered as primary sources and diesel generator as a secondary power source for the system

  7. Automatic control system generation for robot design validation

    Science.gov (United States)

    Bacon, James A. (Inventor); English, James D. (Inventor)

    2012-01-01

    The specification and drawings present a new method, system and software product for and apparatus for generating a robotic validation system for a robot design. The robotic validation system for the robot design of a robotic system is automatically generated by converting a robot design into a generic robotic description using a predetermined format, then generating a control system from the generic robotic description and finally updating robot design parameters of the robotic system with an analysis tool using both the generic robot description and the control system.

  8. F-generation law and recognition of system law

    Institute of Scientific and Technical Information of China (English)

    Shi Kaiquan; Yao Bingxue

    2007-01-01

    If a system is not disturbed (or invaded) by some law, there is no doubt that each system will move according to the expected law and keep stable. Although such a fact often appears, some unknown law breaks into the system and leads it into turbulence. Using function one direction S-rough sets, this article gives the concept of the F-generation law in the system, the generation model of the F-generation law and the recognition method of the system law. Function one direction singular rough sets is a new theory and method in recognizing the disturbance law existing in the system and recognizing the system law.

  9. Computer Generated Hologram System for Wavefront Measurement System Calibration

    Science.gov (United States)

    Olczak, Gene

    2011-01-01

    Computer Generated Holograms (CGHs) have been used for some time to calibrate interferometers that require nulling optics. A typical scenario is the testing of aspheric surfaces with an interferometer placed near the paraxial center of curvature. Existing CGH technology suffers from a reduced capacity to calibrate middle and high spatial frequencies. The root cause of this shortcoming is as follows: the CGH is not placed at an image conjugate of the asphere due to limitations imposed by the geometry of the test and the allowable size of the CGH. This innovation provides a calibration system where the imaging properties in calibration can be made comparable to the test configuration. Thus, if the test is designed to have good imaging properties, then middle and high spatial frequency errors in the test system can be well calibrated. The improved imaging properties are provided by a rudimentary auxiliary optic as part of the calibration system. The auxiliary optic is simple to characterize and align to the CGH. Use of the auxiliary optic also reduces the size of the CGH required for calibration and the density of the lines required for the CGH. The resulting CGH is less expensive than the existing technology and has reduced write error and alignment error sensitivities. This CGH system is suitable for any kind of calibration using an interferometer when high spatial resolution is required. It is especially well suited for tests that include segmented optical components or large apertures.

  10. The Selection of Cooling Systems of Giant Hydro-Generators

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The selection of cooling system for hydro-generator in Ertan Hydropower Station is reviewed in this paper. The new viewpoint on air-cooled system of hydraulic generator of recent years is analyzed and described. That is, "Full air-cooled system is always preferred to inner

  11. Thermoelectric generator cooling system and method of control

    Science.gov (United States)

    Prior, Gregory P; Meisner, Gregory P; Glassford, Daniel B

    2012-10-16

    An apparatus is provided that includes a thermoelectric generator and an exhaust gas system operatively connected to the thermoelectric generator to heat a portion of the thermoelectric generator with exhaust gas flow through the thermoelectric generator. A coolant system is operatively connected to the thermoelectric generator to cool another portion of the thermoelectric generator with coolant flow through the thermoelectric generator. At least one valve is controllable to cause the coolant flow through the thermoelectric generator in a direction that opposes a direction of the exhaust gas flow under a first set of operating conditions and to cause the coolant flow through the thermoelectric generator in the direction of exhaust gas flow under a second set of operating conditions.

  12. Multivariate Permutation Polynomial Systems and Nonlinear Pseudorandom Number Generators

    CERN Document Server

    Ostafe, Alina

    2009-01-01

    In this paper we study a class of dynamical systems generated by iterations of multivariate permutation polynomial systems which lead to polynomial growth of the degrees of these iterations. Using these estimates and the same techniques studied previously for inversive generators, we bound exponential sums along the orbits of these dynamical systems and show that they admit much stronger estimates on average over all initial values than in the general case and thus can be of use for pseudorandom number generation.

  13. Atmospheric fluidized bed combustion advanced concept system. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1992-05-01

    DONLEE Technologies Inc. is developing with support of the US Department of Energy an advanced circulating fluidized bed technology known as the Vortex{trademark} Fluidized Bed Combustor (VFBC). The unique feature of the VFBC is the injection of a significant portion of the combustion air into the cyclone. Since as much as one-half of the total combustion air is injected into the cyclone, the cross-sectional area of the circulating fluidized bed is considerably smaller than typical circulating fluidized beds. The technology is being developed for two applications: Industrial-scale boilers ranging from 20,000 to 100,000 pounds per hour steam generating capacity; and two-stage combustion in which a substoichiometric Vortex Fluidized Bed Combustor (2VFBC) or precombustor is used to generate a combustible gas for use primarily in boiler retrofit applications. This Level II analysis of these two applications indicates that both have merit. An industrial-scale VFBC boiler (60,000 lb/hr of steam) is projected to be economically attractive with coal prices as high as $40 per ton and gas prices between $4 and $5 per thousand cubic feet. The payback time is between 3 and 4 years. The 2VFBC system was evaluated at three capacities of application: 20,000; 60,000 and 100,000 lb/hr of steam. The payback times for these three capacities are 4.5, 2.1 and 1.55 years, respectively. The 2VFBC has potential applications for retrofit of existing pulverized coal-fired boilers or as a new large (utility) boiler. Pressurized operation of the 2VFBC has considerable potential for combined cycle power generation applications. Experimental development of both applications is presented here to demonstrate the potential of these two technologies.

  14. A New Generation of Cool White Dwarf Atmosphere Models Using Ab Initio Calculations

    Science.gov (United States)

    Blouin, S.; Dufour, P.; Kowalski, P. M.

    2017-03-01

    Due to their high photospheric density, cool helium-rich white dwarfs (particularly DZ, DQpec and ultracool) are often poorly described by current atmosphere models. As part of our ongoing efforts to design atmosphere models suitable for all cool white dwarfs, we investigate how the ionization ratio of heavy elements and the H2-He collision-induced absorption (CIA) spectrum are altered under fluid-like densities. For the conditions encountered at the photosphere of cool helium-rich white dwarfs, our ab initio calculations show that the ionization of most metals is inhibited and that the H2-He CIA spectrum is significantly distorted for densities higher than 0.1 g/cm3.

  15. A New Generation of Cool White Dwarf Atmosphere Models Using Ab Initio Calculations

    CERN Document Server

    Blouin, Simon; Kowalski, Piotr M

    2016-01-01

    Due to their high photospheric density, cool helium-rich white dwarfs (particularly DZ, DQpec and ultracool) are often poorly described by current atmosphere models. As part of our ongoing efforts to design atmosphere models suitable for all cool white dwarfs, we investigate how the ionization ratio of heavy elements and the H$_2$-He collision-induced absorption (CIA) spectrum are altered under fluid-like densities. For the conditions encountered at the photosphere of cool helium-rich white dwarfs, our ab initio calculations show that the ionization of most metals is inhibited and that the H$_2$-He CIA spectrum is significantly distorted for densities higher than 0.1 g/cm$^3$.

  16. An Integrated Atmospheric and Hydrological Based Malaria Epidemic Alert System

    Science.gov (United States)

    Asefi Najafabady, S.; Li, J.; Nair, U. S.; Welch, R. M.; Srivastava, A.; Nagpal, B. N.; Saxena, R.; Benedict, M. E.

    2005-05-01

    Malaria is a growing global threat, with increasing morbidity and mortality. In India there have been >40 epidemics in the last five years, in part due to abnormal meteorological conditions as well as the buildup of an immunologically naïve population. In most parts of India, periodic epidemics of malaria occur every five to seven years. Malaria epidemics are serious national/regional health emergencies, occurring with little or no warning where the public health system is unprepared to respond to the emerging problem. However, epidemic conditions develop over several weeks, theoretically allowing time for preventative action. The study area for the proposed research is located in Mewat, south of Delhi. It is estimated that 90% of the malaria burden is influenced by environmental factors, so that successful malaria intervention approaches must be adapted to local environmental conditions. Of particular importance are air and water temperature, relative humidity, soil moisture, and precipitation. Extreme climatic conditions prevail in Mewat, with uneven topography, 450mm average annual rainfall in 25 to 35 days, high temperature variability in different seasons, low relative humidity. Automated surface measurements are obtained for temperature, relative humidity, water temperature, precipitation and soil moisture. The Regional Atmospheric Modeling System (RAMS) is used to predict these variables over the spatial domain which are used in dynamic hydrological models to yield the parameters important to malaria transmission, including surface wetness, mean water table depth, percent surface saturation and total surface runoff. The locations of saturated surface regions associated with mosquito breeding sites near populated regions, along with water temperature, and then are used to determine larvae development and mosquito abundance. ASTER, LANDSAT and MODIS imagery are used to retrieve soil moisture, vegetation indices and land cover types. Pan-sharpened 1m spatial

  17. Next Generation Space Surveillance System-of-Systems

    Science.gov (United States)

    McShane, B.

    2014-09-01

    International economic and military dependence on space assets is pervasive and ever-growing in an environment that is now congested, contested, and competitive. There are a number of natural and man-made risks that need to be monitored and characterized to protect and preserve the space environment and the assets within it. Unfortunately, today's space surveillance network (SSN) has gaps in coverage, is not resilient, and has a growing number of objects that get lost. Risks can be efficiently and effectively mitigated, gaps closed, resiliency improved, and performance increased within a next generation space surveillance network implemented as a system-of-systems with modern information architectures and analytic techniques. This also includes consideration for the newest SSN sensors (e.g. Space Fence) which are born Net-Centric out-of-the-box and able to seamlessly interface with the JSpOC Mission System, global information grid, and future unanticipated users. Significant opportunity exists to integrate legacy, traditional, and non-traditional sensors into a larger space system-of-systems (including command and control centers) for multiple clients through low cost sustainment, modification, and modernization efforts. Clients include operations centers (e.g. JSpOC, USSTRATCOM, CANSPOC), Intelligence centers (e.g. NASIC), space surveillance sensor sites (e.g. AMOS, GEODSS), international governments (e.g. Germany, UK), space agencies (e.g. NASA), and academic institutions. Each has differing priorities, networks, data needs, timeliness, security, accuracy requirements and formats. Enabling processes and technologies include: Standardized and type accredited methods for secure connections to multiple networks, machine-to-machine interfaces for near real-time data sharing and tip-and-queue activities, common data models for analytical processing across multiple radar and optical sensor types, an efficient way to automatically translate between differing client and

  18. Daily atmospheric variability in the South American monsoon system

    Energy Technology Data Exchange (ETDEWEB)

    Krishnamurthy, V. [Institute of Global Environment and Society (IGES), Center for Ocean-Land-Atmosphere Studies (COLA), Calverton, MD (United States); George Mason University, Department of Atmospheric, Oceanic and Earth Sciences, Fairfax, VA (United States); Misra, Vasubandhu [Florida State University, Department of Meteorology and Center for Ocean-Atmospheric Prediction Studies, Tallahassee, FL (United States)

    2011-08-15

    The space-time structure of the daily atmospheric variability in the South American monsoon system has been studied using multichannel singular spectrum analysis of daily outgoing longwave radiation. The three leading eigenmodes are found to have low-frequency variability while four other modes form higher frequency oscillations. The first mode has the same time variability as that of El Nino-Southern Oscillation (ENSO) and exhibits strong correlation with the Pacific sea surface temperature (SST). The second mode varies on a decadal time scale with significant correlation with the Atlantic SST suggesting an association with the Atlantic multidecadal oscillation (AMO). The third mode also has decadal variability but shows an association with the SST of the Pacific decadal oscillation (PDO). The fourth and fifth modes describe an oscillation that has a period of about 165 days and is associated with the North Atlantic oscillation (NAO). The sixth and seventh modes describe an intraseasonal oscillation with a period of 52 days which shows strong relation with the Madden-Julian oscillation. There exists an important difference in the variability of convection between Amazon River Basin (ARB) and central-east South America (CESA). Both regions have similar variations due to ENSO though with higher magnitude in ARB. The AMO-related mode has almost identical variations in the two regions, whereas the PDO-related mode has opposite variations. The interseasonal NAO-related mode also has variations of opposite sign with comparable magnitudes in the two regions. The intraseasonal variability over the CESA is robust while it is very weak over the ARB region. The relative contributions from the low-frequency modes mainly determine the interannual variability of the seasonal mean monsoon although the interseasonal oscillation may contribute in a subtle way during certain years. The intraseasonal variability does not seem to influence the interannual variability in either region

  19. Resilient Control Systems: Next Generation Design Research

    Energy Technology Data Exchange (ETDEWEB)

    Craig Rieger

    2009-05-01

    Since digital control systems were introduced to the market more than 30 years ago, the operational efficiency and stability gained through their use have fueled our migration and ultimate dependence on them for the monitoring and control of critical infrastructure. While these systems have been designed for functionality and reliability, a hostile cyber environment and uncertainties in complex networks and human interactions have placed additional parameters on the design expectations for control systems.

  20. Noise generation in the solid Earth, oceans, and atmosphere, from non-linear interacting surface gravity waves in finite depth

    CERN Document Server

    Ardhuin, Fabrice

    2012-01-01

    Oceanic observations, even in very deep water, and atmospheric pressure or seismic records, from anywhere on Earth, contain noise with dominant periods between 3 and 10 seconds, that can be related to surface gravity waves in the oceans. This noise is consistent with a dominant source explained by a nonlinear wave-wave interaction mechanism, and takes the form of surface gravity waves, acoustic or seismic waves. Previous theoretical works on seismic noise focused on surface (Rayleigh) waves, and did not consider finite depth effects on the generating wave kinematics. These finite depth effects are introduced here, which requires the consideration of the direct wave-induced pressure at the ocean bottom, a contribution previously overlooked in the context of seismic noise. That contribution can lead to a considerable reduction of the seismic noise source, which is particularly relevant for noise periods larger than 10 s. The theory is applied to acoustic waves in the atmosphere, extending previous theories that...

  1. Pyrgeometer Calibration for DOE-Atmospheric System Research Program Using NREL Method (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Reda, I.; Stoffel, T.

    2010-03-15

    Presented at the DOE-Atmospheric System Research Program, Science Team Meeting, 15-19 March 2010, Bethesda, Maryland. The presentation: Pyrgeometer Calibration for DOE-Atmospheric System Research program using NREL Method - was presented by Ibrahim Reda and Tom Stoffel on March 15, 2010 at the 2010 ASR Science Team Meeting. March 15-19, 2010, Bethesda, Maryland.

  2. 78 FR 70076 - Aging Management of Internal Surfaces, Fire Water Systems, Atmospheric Storage Tanks, and...

    Science.gov (United States)

    2013-11-22

    ... COMMISSION Aging Management of Internal Surfaces, Fire Water Systems, Atmospheric Storage Tanks, and... Guidance (LR-ISG), LR-ISG-2012-02, ``Aging Management of Internal Surfaces, Fire Water Systems, Atmospheric... aging management programs (AMPs), aging management review (AMR) items, and definitions in NUREG-...

  3. Multi-Meteotsunami Event in the Adriatic Sea Generated by Atmospheric Disturbances of 25-26 June 2014

    Science.gov (United States)

    Šepić, Jadranka; Međugorac, Iva; Janeković, Ivica; Dunić, Natalija; Vilibić, Ivica

    2016-12-01

    A series of meteotsunamis hit a few locations in the Mediterranean and Black Seas during 22-27 June 2014. Meteotsunamis were particularly numerous on 25 and 26 June in the Adriatic Sea, where at least six harbours and bays were stricken by powerful waves: strongest events occurred in Vela Luka (Korčula Island), a known meteotsunami hot-spot, where waves reached height of 3 m, and in Rijeka dubrovačka Bay, where strong 5 m/s currents accompanied 2.5 m high waves. Intensification of high-frequency sea level activity was observed at both the eastern and western Adriatic tide gauge stations, with maximum recorded wave heights reaching 68 cm (Ortona, Italy). A series of individual air pressure disturbances characterized by pronounced rates of air pressure change (up to 2.4 hPa/5 min), limited spatial extent ( 50 km) and high temporal variability, propagated over the Adriatic on 2 days in question. Numerical hydrodynamic model SCHISM forced by measured and idealised air pressure disturbances was utilised to reproduce the observed Adriatic sea level response. Several important conclusions were reached: (1) meteotsunamis occurring at various parts of the coast were generated by different atmospheric air pressure disturbances; (2) topographic influence can be removed from sea level spectra by computing spectral signal-to-background ratios; the result, being related to the external forcing, resembles atmospheric pressure spectra; (3) sea response is strongly dependant on details of atmospheric forcing; and (4) over complex bathymetries, like the middle and south Adriatic ones, numerous effects, including Proudman resonance, edge waves, strong topographical enhancement and refractions on the islands placed on the pathway of atmospheric disturbances should be taken into account to fully understand meteotsunami generation and dynamics. An in-depth numerical study is planned to supplement the latter conclusion and to quantify contribution of each process.

  4. Multi-Meteotsunami Event in the Adriatic Sea Generated by Atmospheric Disturbances of 25-26 June 2014

    Science.gov (United States)

    Šepić, Jadranka; Međugorac, Iva; Janeković, Ivica; Dunić, Natalija; Vilibić, Ivica

    2016-01-01

    A series of meteotsunamis hit a few locations in the Mediterranean and Black Seas during 22-27 June 2014. Meteotsunamis were particularly numerous on 25 and 26 June in the Adriatic Sea, where at least six harbours and bays were stricken by powerful waves: strongest events occurred in Vela Luka (Korčula Island), a known meteotsunami hot-spot, where waves reached height of ~3 m, and in Rijeka dubrovačka Bay, where strong ~5 m/s currents accompanied ~2.5 m high waves. Intensification of high-frequency sea level activity was observed at both the eastern and western Adriatic tide gauge stations, with maximum recorded wave heights reaching ~68 cm (Ortona, Italy). A series of individual air pressure disturbances characterized by pronounced rates of air pressure change (up to 2.4 hPa/5 min), limited spatial extent (~50 km) and high temporal variability, propagated over the Adriatic on 2 days in question. Numerical hydrodynamic model SCHISM forced by measured and idealised air pressure disturbances was utilised to reproduce the observed Adriatic sea level response. Several important conclusions were reached: (1) meteotsunamis occurring at various parts of the coast were generated by different atmospheric air pressure disturbances; (2) topographic influence can be removed from sea level spectra by computing spectral signal-to-background ratios; the result, being related to the external forcing, resembles atmospheric pressure spectra; (3) sea response is strongly dependant on details of atmospheric forcing; and (4) over complex bathymetries, like the middle and south Adriatic ones, numerous effects, including Proudman resonance, edge waves, strong topographical enhancement and refractions on the islands placed on the pathway of atmospheric disturbances should be taken into account to fully understand meteotsunami generation and dynamics. An in-depth numerical study is planned to supplement the latter conclusion and to quantify contribution of each process.

  5. Effect of nitrogen addition to ozone generation characteristics by diffuse and filamentary dielectric barrier discharges at atmospheric pressure

    Science.gov (United States)

    Osawa, Naoki; Tsuji, Takafumi; Ogiso, Ryota; Yoshioka, Yoshio

    2017-05-01

    Ozone is widely used for gas treatment, advanced oxidation processes, microorganisms inactivation, etc. In this research, we investigated the effect of nitrogen addition to ozone generation characteristics by atmospheric pressure Townsend discharge (APTD) type and filamentary dielectric barrier discharge (DBD) type ozone generators. The result showed that the ozone generated by the filamentary DBD increases rapidly with the increase of O2 content, and is higher than that by the APTD. On the other hand, it is interesting that the ozone generated by the APTD gradually decreases with the increase of O2 content. In order to clarify why the characteristics of ozone generation by the two kinds of discharge modes showed different dependency to the N2 content, we analyzed the exhaust gas composition using FTIR spectroscopy and calculated the rate coefficients using BOLSIG+ code. As a result, we found that although O2 content decreased with increasing N2 content, additional O atoms produced by excited N2 molecules contribute to ozone generation in case of APTD. Contribution to the topical issue "The 15th International Symposium on High Pressure Low Temperature Plasma Chemistry (HAKONE XV)", edited by Nicolas Gherardi and Tomáš Hoder

  6. Dependence of Ozone Generation on Gas Temperature Distribution in AC Atmospheric Pressure Dielectric Barrier Discharge in Oxygen

    Science.gov (United States)

    Takahashi, Go; Akashi, Haruaki

    AC atmospheric pressure multi-filament dielectric barrier discharge in oxygen has been simulated using two dimensional fluid model. In the discharge, three kinds of streamers have been obtained. They are primary streamers, small scale streamers and secondary streamers. The primary streamers are main streamers in the discharge and the small scale streamers are formed after the ceasing of the primary streamers. And the secondary streamers are formed on the trace of the primary streamers. In these streamers, the primary and the small scale streamers are very effective to generate O(3P) oxygen atoms which are precursor of ozone. And the ozone is generated mainly in the vicinity of the dielectrics. In high gas temperature region, ozone generation decreases in general. However, increase of the O(3P) oxygen atom density in high gas temperature region compensates decrease of ozone generation rate coefficient. As a result, amount of ozone generation has not changed. But if the effect of gas temperature was neglected, amount of ozone generation increases 10%.

  7. Batch Private Keys Generation for RSA in Security Communication Systems

    Institute of Scientific and Technical Information of China (English)

    CHEN Yun; CHEN Xin

    2005-01-01

    RSA public key cryptosystem is extensively used in information security systems.However, key generation for RSA cryptosystem requires multiplicative inversion over finite field, which has higher computational complexity, compared with either multiplication in common sense or modular multiplication over finite field. In order to improve the performance of key generation, we propose a batch private keys generation method in this paper. The method derives efficiency from cutting down multiplicative inversions over finite field. Theoretical analysis shows that the speed of batch private keys generation for s users is faster than that of s times solo private key generation. It is suitable for applications in those systems with large amount of users.

  8. System Supporting Automatic Generation of Finite Element Using Image Information

    Institute of Scientific and Technical Information of China (English)

    J; Fukuda

    2002-01-01

    A mesh generating system has been developed in orde r to prepare large amounts of input data which are needed for easy implementation of a finite element analysis. This system consists of a Pre-Mesh Generator, an Automatic Mesh Generator and a Mesh Modifier. Pre-Mesh Generator produces the shape and sub-block information as input data of Automatic Mesh Generator by c arrying out various image processing with respect to the image information of th e drawing input using scanner. Automatic Mesh Generato...

  9. Development of non-thermal atmospheric pressure plasma system for surface modification of polymeric materials

    Science.gov (United States)

    Kasih, T. P.

    2017-04-01

    Non-thermal plasma has become one of the new technologies which are highly developed now days. This happens because the cold plasma using the principle of generated reactive gases that have the ability to modify the surface properties of a material or product without changing the original characteristics of the material. The purpose of this study is to develop a cold plasma system that operates at atmospheric pressure and investigates the effect of cold plasma treatment to change the surface characteristics of the polymer material polyethylene (PE) at various time conditions. We are successfully developing a non-thermal plasma system that can operate at atmospheric pressure and can be run with Helium or Argon gas. The characteristics of plasma will be discussed from the view of its electrical property, plasma discharge regime andoperation temperature. Experiment results on plasma treatment on PE material shows the changes of surface properties of originally hydrophobic material PE becomes hydrophilic by only few seconds of plasma treatment and level of hydrophilicity become greater with increasing duration of plasma treatment. Confirmation of this is shown by the measurement of contact angle of droplets of water on the surface of PE are getting smaller.

  10. The Topo-trigger: a new concept of stereo trigger system for imaging atmospheric Cherenkov telescopes

    CERN Document Server

    López-Coto, Rubén; Paoletti, Riccardo; Bigas, Oscar Blanch; Cortina, Juan

    2016-01-01

    Imaging atmospheric Cherenkov telescopes (IACTs) such as the Major Atmospheric Gamma-ray Imaging Cherenkov (MAGIC) telescopes endeavor to reach the lowest possible energy threshold. In doing so the trigger system is a key element. Reducing the trigger threshold is hampered by the rapid increase of accidental triggers generated by ambient light, the so-called Night Sky Background (NSB). In this paper we present a topological trigger, dubbed Topo-trigger, which rejects events on the basis of their relative orientation in the telescope cameras. We have simulated and tested the trigger selection algorithm in the MAGIC telescopes. The algorithm was tested using MonteCarlo simulations and shows a rejection of 85% of the accidental stereo triggers while preserving 99 % of the gamma rays. A full implementation of this trigger system would achieve an increase in collection area between 10 and 20% at the energy threshold. The analysis energy threshold of the instrument is expected to decrease by ?8 %. The selection alg...

  11. Development of a Generator Stator Insulation System.

    Science.gov (United States)

    1983-04-01

    16 - ’ ’ , .. . .- " ’ m’ mm II- - mm system will see. The primary factors that bear on suitability of an insulation system for this application are...heavily covered with a black gummy deposit. Both of these areas appeared suspect and were investigated further. It appeared that the long-time failure

  12. Design Optimization and Evaluation of Different Wind Generator Systems

    DEFF Research Database (Denmark)

    Chen, Zhe; Li, Hui

    2008-01-01

    -stage gearbox (DFIG_3G) and with the single-stage gearbox (DFIG_1G), the electricity excited synchronous generator with the direct-driven (EESG_DD), and the VSCF squirrel cage induction generator with the three-stage gearbox (SCIG_3G). Firstly, the design models of wind turbines, three/single stage gearbox......With rapid development of wind power technologies and significant growth of wind power capacity installed worldwide, various wind generator systems have been developed and built. The objective of this paper is to evaluate various wind generator systems by optimization designs and comparisons....... In this paper, seven variable speed constant frequency (VSCF) wind generator systems are investigated, namely permanent magnet synchronous generators with the direct-driven (PMSG_DD), the single-stage gearbox (PMSG_1G) and three-stage gearbox (PMSG_3G) concepts, doubly fed induction generators with the three...

  13. Summary of atmospheric wind design criteria for wind energy conversion system development

    Science.gov (United States)

    Frost, W.; Turner, R. E.

    1979-01-01

    Basic design values are presented of significant wind criteria, in graphical format, for use in the design and development of wind turbine generators for energy research. It is a condensed version of portions of the Engineering Handbook on the Atmospheric Environmental Guidelines for Use in Wind Turbine Generator Development.

  14. A horizontal mobile measuring system for atmospheric quantities

    Directory of Open Access Journals (Sweden)

    J. Hübner

    2014-05-01

    Full Text Available A fully automatic Horizontal Mobile Measuring System (HMMS for atmospheric quantities has been developed. The HMMS is based on the drive mechanism of a garden railway system and can be installed at any location and with any measuring track. In addition to meteorological quantities (temperature, humidity and short/long-wave down/upwelling radiation, HMMS also measures trace gas concentrations (carbon dioxide and ozone. While sufficient spatial resolution is a problem even for measurements on distributed towers, this could be easily achieved with the HMMS, which has been specifically developed to obtain higher information density about horizontal gradients in a heterogeneous forest ecosystem. There, horizontal gradients of meteorological quantities and trace gases could be immense, particularly at the transition from a dense forest to an open clearing, with large impact on meteorological parameters and exchange processes. Consequently, HMMS was firstly applied during EGER IOP3 project (ExchanGE processes in mountainous Regions – Intense Observation Period 3 in the Fichtelgebirge Mountains (SE Germany during summer 2011. At a constant 1 m above ground, the measuring track of the HMMS consisted of a straight line perpendicular to the forest edge, starting in the dense spruce forest and leading 75 m into an open clearing. Tags with bar codes, mounted every meter on the wooden substructure, allowed (a keeping the speed of the HMMS constant (approx. 0.5 m s−1 and (b operation of the HMMS in a continuous back and forth running mode. During EGER IOP3, HMMS was operational for almost 250 h. Results show that – due to considerably long response times (between 4 s and 20 s of commercial temperature, humidity and the radiation sensors – true spatial variations of the meteorological quantities could not be adequately captured (mainly at the forest edge. Corresponding dynamical (spatial errors of the measurement values were corrected on the basis of

  15. Next-Generation Shipboard DC Power System

    DEFF Research Database (Denmark)

    Jin, Zheming; Sulligoi, Giorgio; Cuzner, Rob

    2016-01-01

    In recent years, more and more evidence suggests that the global energy system is on the verge of a drastic revolution. The evolutionary development in power electronic technologies, the emerging high-performance energy storage devices, as well as the ever increasing penetration of renewable energy...... sources (RES) are commonly recognized as the major driven force of the revolution, the outburst of customer electronics and new kinds of household electronics is also powering this change. In this context, dc power distribution technologies have made a comeback and keep gaining a commendable increase......, aerospace/aircraft power systems, as well as maritime power systems....

  16. The Rapid Atmospheric Monitoring System of the Pierre Auger Observatory

    CERN Document Server

    Abreu, P; Ahlers, M; Ahn, E J; Albuquerque, I F M; Allard, D; Allekotte, I; Allen, J; Allison, P; Almela, A; Castillo, J Alvarez; Alvarez-Muñiz, J; Batista, R Alves; Ambrosio, M; Aminaei, A; Anchordoqui, L; Andringa, S; Antičić, T; Aramo, C; Arganda, E; Arqueros, F; Asorey, H; Assis, P; Aublin, J; Ave, M; Avenier, M; Avila, G; Badescu, A M; Balzer, M; Barber, K B; Barbosa, A F; Bardenet, R; Barroso, S L C; Baughman, B; Bäuml, J; Baus, C; Beatty, J J; Becker, K H; Bellétoile, A; Bellido, J A; BenZvi, S; Berat, C; Bertou, X; Biermann, P L; Billoir, P; Blanco, F; Blanco, M; Bleve, C; Blümer, H; Boháčová, M; Boncioli, D; Bonifazi, C; Bonino, R; Borodai, N; Brack, J; Brancus, I; Brogueira, P; Brown, W C; Bruijn, R; Buchholz, P; Bueno, A; Buroker, L; Burton, R E; Caballero-Mora, K S; Caccianiga, B; Caramete, L; Caruso, R; Castellina, A; Catalano, O; Cataldi, G; Cazon, L; Cester, R; Chauvin, J; Cheng, S H; Chiavassa, A; Chinellato, J A; Diaz, J Chirinos; Chudoba, J; Cilmo, M; Clay, R W; Cocciolo, G; Collica, L; Coluccia, M R; Conceição, R; Contreras, F; Cook, H; Cooper, M J; Coppens, J; Cordier, A; Coutu, S; Covault, C E; Creusot, A; Criss, A; Cronin, J; Curutiu, A; Dagoret-Campagne, S; Dallier, R; Daniel, B; Dasso, S; Daumiller, K; Dawson, B R; de Almeida, R M; De Domenico, M; De Donato, C; de Jong, S J; De La Vega, G; Junior, W J M de Mello; Neto, J R T de Mello; De Mitri, I; de Souza, V; de Vries, K D; del Peral, L; del Río, M; Deligny, O; Dembinski, H; Dhital, N; Di Giulio, C; Castro, M L Díaz; Diep, P N; Diogo, F; Dobrigkeit, C; Docters, W; D'Olivo, J C; Dong, P N; Dorofeev, A; Anjos, J C dos; Dova, M T; D'Urso, D; Dutan, I; Ebr, J; Engel, R; Erdmann, M; Escobar, C O; Espadanal, J; Etchegoyen, A; Luis, P Facal San; Falcke, H; Fang, K; Farrar, G; Fauth, A C; Fazzini, N; Ferguson, A P; Fick, B; Figueira, J M; Filevich, A; Filipčič, A; Fliescher, S; Fracchiolla, C E; Fraenkel, E D; Fratu, O; Fröhlich, U; Fuchs, B; Gaior, R; Gamarra, R F; Gambetta, S; García, B; Roca, S T Garcia; Garcia-Gamez, D; Garcia-Pinto, D; Garilli, G; Bravo, A Gascon; Gemmeke, H; Ghia, P L; Giller, M; Gitto, J; Glass, H; Gold, M S; Golup, G; Albarracin, F Gomez; Berisso, M Gómez; Vitale, P F Gómez; Gonçalves, P; Gonzalez, J G; Gookin, B; Gorgi, A; Gouffon, P; Grashorn, E; Grebe, S; Griffith, N; Grillo, A F; Guardincerri, Y; Guarino, F; Guedes, G P; Hansen, P; Harari, D; Harrison, T A; Harton, J L; Haungs, A; Hebbeker, T; Heck, D; Herve, A E; Hojvat, C; Hollon, N; Holmes, V C; Homola, P; Hörandel, J R; Horvath, P; Hrabovský, M; Huber, D; Huege, T; Insolia, A; Ionita, F; Italiano, A; Jansen, S; Jarne, C; Jiraskova, S; Josebachuili, M; Kadija, K; Kampert, K H; Karhan, P; Kasper, P; Katkov, I; Kégl, B; Keilhauer, B; Keivani, A; Kelley, J L; Kemp, E; Kieckhafer, R M; Klages, H O; Kleifges, M; Kleinfeller, J; Knapp, J; Koang, D -H; Kotera, K; Krohm, N; Krömer, O; Kruppke-Hansen, D; Kuempel, D; Kulbartz, J K; Kunka, N; La Rosa, G; Lachaud, C; LaHurd, D; Latronico, L; Lauer, R; Lautridou, P; Coz, S Le; Leão, M S A B; Lebrun, D; Lebrun, P; de Oliveira, M A Leigui; Letessier-Selvon, A; Lhenry-Yvon, I; Link, K; López, R; Agüera, A Lopez; Louedec, K; Bahilo, J Lozano; Lu, L; Lucero, A; Ludwig, M; Lyberis, H; Maccarone, M C; Macolino, C; Maldera, S; Maller, J; Mandat, D; Mantsch, P; Mariazzi, A G; Marin, J; Marin, V; Maris, I C; Falcon, H R Marquez; Marsella, G; Martello, D; Martin, L; Martinez, H; Bravo, O Martínez; Martraire, D; Meza, J J Masías; Mathes, H J; Matthews, J; Matthews, J A J; Matthiae, G; Maurel, D; Maurizio, D; Mazur, P O; Medina-Tanco, G; Melissas, M; Melo, D; Menichetti, E; Menshikov, A; Mertsch, P; Meurer, C; Meyhandan, R; Mićanović, S; Micheletti, M I; Minaya, I A; Miramonti, L; Molina-Bueno, L; Mollerach, S; Monasor, M; Ragaigne, D Monnier; Montanet, F; Morales, B; Morello, C; Moreno, E; Moreno, J C; Mostafá, M; Moura, C A; Muller, M A; Müller, G; Münchmeyer, M; Mussa, R; Navarra, G; Navarro, J L; Navas, S; Necesal, P; Nellen, L; Nelles, A; Neuser, J; Nhung, P T; Niechciol, M; Niemietz, L; Nierstenhoefer, N; Nitz, D; Nosek, D; Nožka, L; Oehlschläger, J; Olinto, A; Ortiz, M; Pacheco, N; Selmi-Dei, D Pakk; Palatka, M; Pallotta, J; Palmieri, N; Parente, G; Parizot, E; Parra, A; Pastor, S; Paul, T; Pech, M; Pȩkala, J; Pelayo, R; Pepe, I M; Perrone, L; Pesce, R; Petermann, E; Petrera, S; Petrolini, A; Petrov, Y; Pfendner, C; Piegaia, R; Pierog, T; Pieroni, P; Pimenta, M; Pirronello, V; Platino, M; Plum, M; Ponce, V H; Pontz, M; Porcelli, A; Privitera, P; Prouza, M; Quel, E J; Querchfeld, S; Rautenberg, J; Ravel, O; Ravignani, D; Revenu, B; Ridky, J; Riggi, S; Risse, M; Ristori, P; Rivera, H; Rizi, V; Roberts, J; de Carvalho, W Rodrigues; Rodriguez, G; Cabo, I Rodriguez; Martino, J Rodriguez; Rojo, J Rodriguez; Rodríguez-Frías, M D; Ros, G; Rosado, J; Rossler, T; Roth, M; Rouillé-d'Orfeuil, B; Roulet, E; Rovero, A C; Rühle, C; Saftoiu, A; Salamida, F; Salazar, H; Greus, F Salesa; Salina, G; Sánchez, F; Santo, C E; Santos, E; Santos, E M; Sarazin, F; Sarkar, B; Sarkar, S; Sato, R; Scharf, N; Scherini, V; Schieler, H; Schiffer, P; Schmidt, A; Scholten, O; Schoorlemmer, H; Schovancova, J; Schovánek, P; Schröder, F; Schulte, S; Schuster, D; Sciutto, S J; Scuderi, M; Segreto, A; Settimo, M; Shadkam, A; Shellard, R C; Sidelnik, I; Sigl, G; Lopez, H H Silva; Sima, O; Śmiałkowski, A; Šmída, R; Snow, G R; Sommers, P; Sorokin, J; Spinka, H; Squartini, R; Srivastava, Y N; Stanic, S; Stapleton, J; Stasielak, J; Stephan, M; Stutz, A; Suarez, F; Suomijärvi, T; Supanitsky, A D; Šuša, T; Sutherland, M S; Swain, J; Szadkowski, Z; Szuba, M; Tapia, A; Tartare, M; Taşcău, O; Tcaciuc, R; Thao, N T; Thomas, D; Tiffenberg, J; Timmermans, C; Tkaczyk, W; Peixoto, C J Todero; Toma, G; Tomankova, L; Tomé, B; Tonachini, A; Travnicek, P; Tridapalli, D B; Tristram, G; Trovato, E; Tueros, M; Ulrich, R; Unger, M; Urban, M; Galicia, J F Valdés; Valiño, I; Valore, L; van Aar, G; Berg, A M van den; van Vliet, A; Varela, E; Cárdenas, B Vargas; Vázquez, J R; Vázquez, R A; Veberič, D; Verzi, V; Vicha, J; Videla, M; Villaseñor, L; Wahlberg, H; Wahrlich, P; Wainberg, O; Walz, D; Watson, A A; Weber, M; Weidenhaupt, K; Weindl, A; Werner, F; Westerhoff, S; Whelan, B J; Widom, A; Wieczorek, G; Wiencke, L; Wilczyńska, B; Wilczyński, H; Will, M; Williams, C; Winchen, T; Wommer, M; Wundheiler, B; Yamamoto, T; Yapici, T; Younk, P; Yuan, G; Yushkov, A; Garcia, B Zamorano; Zas, E; Zavrtanik, D; Zavrtanik, M; Zaw, I; Zepeda, A; Zhou, J; Zhu, Y; Silva, M Zimbres; Ziolkowski, M

    2012-01-01

    The Pierre Auger Observatory is a facility built to detect air showers produced by cosmic rays above 10^17 eV. During clear nights with a low illuminated moon fraction, the UV fluorescence light produced by air showers is recorded by optical telescopes at the Observatory. To correct the observations for variations in atmospheric conditions, atmospheric monitoring is performed at regular intervals ranging from several minutes (for cloud identification) to several hours (for aerosol conditions) to several days (for vertical profiles of temperature, pressure, and humidity). In 2009, the monitoring program was upgraded to allow for additional targeted measurements of atmospheric conditions shortly after the detection of air showers of special interest, e.g., showers produced by very high-energy cosmic rays or showers with atypical longitudinal profiles. The former events are of particular importance for the determination of the energy scale of the Observatory, and the latter are characteristic of unusual air show...

  17. Analysis of longwave radiation for the Earth-atmosphere system

    Science.gov (United States)

    Tiwari, S. N.; Venuru, C. S.; Subramanian, S. V.

    1983-01-01

    Accurate radiative transfer models are used to determine the upwelling atmospheric radiance and net radiative flux in the entire longwave spectral range. The validity of the quasi-random band model is established by comparing the results of this model with those of line-by-line formulations and with available theoretical and experimental results. Existing radiative transfer models and computer codes are modified to include various surface and atmospheric effects (surface reflection, nonequilibrium radiation, and cloud effects). The program is used to evaluate the radiative flux in clear atmosphere, provide sensitivity analysis of upwelling radiance in the presence of clouds, and determine the effects of various climatological parameters on the upwelling radiation and anisotropic function. Homogeneous and nonhomogeneous gas emissivities can also be evaluated under different conditions.

  18. An Adaptive Multivariable Control System for Hydroelectric Generating Units

    Directory of Open Access Journals (Sweden)

    Gunne J. Hegglid

    1983-04-01

    Full Text Available This paper describes an adaptive multivariable control system for hydroelectric generating units. The system is based on a detailed mathematical model of the synchronous generator, the water turbine, the exiter system and turbine control servo. The models of the water penstock and the connected power system are static. These assumptions are not considered crucial. The system uses a Kalman filter for optimal estimation of the state variables and the parameters of the electric grid equivalent. The multivariable control law is computed from a Riccatti equation and is made adaptive to the generators running condition by means of a least square technique.

  19. The Next Generation ATLAS Production System

    CERN Document Server

    Borodin, Mikhail; The ATLAS collaboration; Golubkov, Dmitry; Klimentov, Alexei; Maeno, Tadashi; Mashinistov, Ruslan; Vaniachine, Alexandre

    2015-01-01

    The ATLAS experiment at LHC data processing and simulation grows continuously, as more data and more use cases emerge. For data processing the ATLAS experiment adopted the data transformation approach, where software applications transform the input data into outputs. In the ATLAS production system, each data transformation is represented by a task, a collection of many jobs, dynamically submitted by the ATLAS workload management system (PanDA/JEDI) and executed on the Grid, clouds and supercomputers. Patterns in ATLAS data transformation workflows composed of many tasks provided a scalable production system framework for template definitions of the many-tasks workflows. User interface and system logic of these workflows are being implemented in the Database Engine for Tasks (DEFT). Such development required using modern computing technologies and approaches. We report technical details of this development: database implementation, server logic and Web user interface technologies.

  20. Combustion driven ammonia generation strategies for passive ammonia SCR system

    Science.gov (United States)

    Toner, Joel G.; Narayanaswamy, Kushal; Szekely, Jr., Gerald A.; Najt, Paul M.

    2016-12-06

    A method for controlling ammonia generation in an exhaust gas feedstream output from an internal combustion engine equipped with an exhaust aftertreatment system including a first aftertreatment device includes executing an ammonia generation cycle to generate ammonia on the first aftertreatment device. A desired air-fuel ratio output from the engine and entering the exhaust aftertreatment system conducive for generating ammonia on the first aftertreatment device is determined. Operation of a selected combination of a plurality of cylinders of the engine is selectively altered to achieve the desired air-fuel ratio entering the exhaust aftertreatment system.

  1. Characterization of a copper spark discharge plasma in argon atmosphere used for nanoparticle generation

    Science.gov (United States)

    Kohut, Attila; Galbács, Gábor; Márton, Zsuzsanna; Geretovszky, Zsolt

    2017-04-01

    Spark discharge nanoparticle generation is a dynamically developing application of discharge plasmas. In the present study a spark plasma used for nanoparticle generation is characterized by means of spatially and temporally resolved optical emission spectroscopy (OES) supplemented by fast imaging. The data acquired during the generation of copper nanoparticles in argon ambient is used to describe the spatial and temporal evolution of the species in the spark gap and to derive plasma parameters such as excitation temperature and electron concentration on one hand, and the concentration of the Cu species eroded by a single spark on the other. It is shown that temporally and spatially resolved OES together with a simple equilibrium model are efficient tools to estimate the characteristics of the spark discharge plasma that typically exists in spark discharge nanoparticle generators.

  2. Next Generation Operational Control System (OCX)

    Science.gov (United States)

    2015-12-01

    UNCLASSIFIED 5 Mission and Description The Global Positioning System (GPS) is a space-based positioning, navigation, and timing distribution system, which...operates through weather and electromagnetic environments (jamming, spoofing, etc.). GPS supports both civil and military users in air, space, sea, and...a complex incentive structure; and high government personnel turnover. The Program Office and Raytheon have worked to address the root causes

  3. Improved Meteorological Input for Atmospheric Release Decision support Systems and an Integrated LES Modeling System for Atmospheric Dispersion of Toxic Agents: Homeland Security Applications

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, E; Simpson, M; Larsen, S; Gash, J; Aluzzi, F; Lundquist, J; Sugiyama, G

    2010-04-26

    When hazardous material is accidently or intentionally released into the atmosphere, emergency response organizations look to decision support systems (DSSs) to translate contaminant information provided by atmospheric models into effective decisions to protect the public and emergency responders and to mitigate subsequent consequences. The Department of Homeland Security (DHS)-led Interagency Modeling and Atmospheric Assessment Center (IMAAC) is one of the primary DSSs utilized by emergency management organizations. IMAAC is responsible for providing 'a single piont for the coordination and dissemination of Federal dispersion modeling and hazard prediction products that represent the Federal position' during actual or potential incidents under the National Response Plan. The Department of Energy's (DOE) National Atmospheric Release Advisory Center (NARAC), locatec at the Lawrence Livermore National Laboratory (LLNL), serves as the primary operations center of the IMAAC. A key component of atmospheric release decision support systems is meteorological information - models and data of winds, turbulence, and other atmospheric boundary-layer parameters. The accuracy of contaminant predictions is strongly dependent on the quality of this information. Therefore, the effectiveness of DSSs can be enhanced by improving the meteorological options available to drive atmospheric transport and fate models. The overall goal of this project was to develop and evaluate new meteorological modeling capabilities for DSSs based on the use of NASA Earth-science data sets in order to enhance the atmospheric-hazard information provided to emergency managers and responders. The final report describes the LLNL contributions to this multi-institutional effort. LLNL developed an approach to utilize NCAR meteorological predictions using NASA MODIS data for the New York City (NYC) region and demonstrated the potential impact of the use of different data sources and data

  4. Grid Monitoring and Advanced Control of Distributed Power Generation Systems

    OpenAIRE

    Timbus, Adrian Vasile

    2007-01-01

    The movement towards a clean technology for energy production and the constraints in reducing the CO2 emissions are some factors facilitating the growth of distributed power generation systems based on renewable energy resources. Consequently, large penetration of distributed generators has been reported in some countries creating concerns about power system stability. This leads to a continuous evolution of grid interconnection requirements towards a better controllability of generated power...

  5. Windfarm generation assessment for reliability analysis of power systems

    DEFF Research Database (Denmark)

    Negra, N.B.; Holmstrøm, O.; Bak-Jensen, B.;

    2007-01-01

    Due to the fast development of wind generation in the past ten years, increasing interest has been paid to techniques for assessing different aspects of power systems with a large amount of installed wind generation. One of these aspects concerns power system reliability. Windfarm modelling plays...

  6. Synchronization Methods for Three Phase Distributed Power Generation Systems

    DEFF Research Database (Denmark)

    Timbus, Adrian Vasile; Teodorescu, Remus; Blaabjerg, Frede

    2005-01-01

    Nowadays, it is a general trend to increase the electricity production using Distributed Power Generation Systems (DPGS) based on renewable energy resources such as wind, sun or hydrogen. If these systems are not properly controlled, their connection to the utility network can generate problems o...

  7. 270 Volt Direct Current Generating System Design, Development and Test

    Science.gov (United States)

    1991-08-01

    is greatly influenced by the load (provides bias to the undervoltage detection circuit) the specific system generator carries. Therefore, when the...1 in the following positions. SI, S2 - Position I S3, S4 - Position 2 GCSv - "ONO Connect the system ( Generator . GCU, CS #1 V #2, LC and BTC) as

  8. Solar Energy Systems for Lunar Oxygen Generation

    Science.gov (United States)

    Colozza, Anthony J.; Heller, Richard S.; Wong, Wayne A.; Hepp, Aloysius F.

    2010-01-01

    An evaluation of several solar concentrator-based systems for producing oxygen from lunar regolith was performed. The systems utilize a solar concentrator mirror to provide thermal energy for the oxygen production process. Thermal energy to power a Stirling heat engine and photovoltaics are compared for the production of electricity. The electricity produced is utilized to operate the equipment needed in the oxygen production process. The initial oxygen production method utilized in the analysis is hydrogen reduction of ilmenite. Utilizing this method of oxygen production a baseline system design was produced. This baseline system had an oxygen production rate of 0.6 kg/hr with a concentrator mirror size of 5 m. Variations were performed on the baseline design to show how changes in the system size and process (rate) affected the oxygen production rate. An evaluation of the power requirements for a carbothermal lunar regolith reduction reactor has also been conducted. The reactor had a total power requirement between 8,320 to 9,961 W when producing 1000 kg/year of oxygen. The solar concentrator used to provide the thermal power (over 82 percent of the total energy requirement) would have a diameter of less than 4 m.

  9. Photosynthesis of Quercus suber is affected by atmospheric NH3 generated by multifunctional agrosystems.

    Science.gov (United States)

    Pintó-Marijuan, Marta; Da Silva, Anabela Bernardes; Flexas, Jaume; Dias, Teresa; Zarrouk, Olfa; Martins-Loução, Maria Amélia; Chaves, Maria Manuela; Cruz, Cristina

    2013-12-01

    Montados are evergreen oak woodlands dominated by Quercus species, which are considered to be key to biodiversity conservation and ecosystem services. This ecosystem is often used for cattle breeding in most regions of the Iberian Peninsula, which causes plants to receive extra nitrogen as ammonia (NH(3)) through the atmosphere. The effect of this atmospheric NH(3) (NH(3atm)) on ecosystems is still under discussion. This study aimed to evaluate the effects of an NH(3atm) concentration gradient downwind of a cattle barn in a Montado area. Leaves from the selected Quercus suber L. trees along the gradient showed a clear influence of the NH(3) on δ(13)C, as a consequence of a strong limitation on the photosynthetic machinery by a reduction of both stomatal and mesophyll conductance. A detailed study of the impact of NH(3atm) on the photosynthetic performance of Q. suber trees is presented, and new mechanisms by which NH(3) affects photosynthesis at the leaf level are suggested.

  10. Behavior of iodine in the atmosphere-soil-plant system

    Energy Technology Data Exchange (ETDEWEB)

    Muramatsu, Yasuyuki; Yoshida, Satoshi; Uchida, Shigeo [National Inst. of Radiological Sciences, Hitachinaka, Ibaraki (Japan). Nakaminato Lab. Branch

    1996-12-31

    Levels and behavior of radioactive and stable iodine in the environment were studied to obtain parameter values for the assessment of {sup 129}I released from nuclear facilities. The deposition velocity (V{sub D}) of gaseous iodine from the atmosphere to rice grains (rough rice) was 0.00048 cm{sup 3} g{sup -1}s{sup -1} for CH{sub 3}I and 0.15 cm{sup 3} g{sup -1}s{sup -1} for I{sub 2}. The ratio of the iodine distribution in a grain exposed to CH{sub 3}I was as follows, rough rice : brown rice (hulled rice) : polished rice = 1.0 : 0.49 : 0.38. The distribution ratio in polished rice for CH{sub 3}I was about 20 times higher than that for I{sub 2}. The soil-solution distribution coefficient (K{sub d}) for both I{sup -} and IO{sub 3}{sup -} varied very widely, i.e. <0.1 to 8000 ml g{sup -1}. High values were found in soils having high concentrations of total organic carbon, active-Al and active-Fe (Al and Fe extracted by a mixture of oxalic acid and ammonium oxalate). Andosol, one of the most typical Japanese soils derived from deposits of volcanic ash, showed specifically high K{sub d} values. The soil-to-plant transfer factors (or concentration ratio) in the edible parts of crops were in the range 0.0002-0.016. The transfer factors for tomato, sweet potato, carrot, soybeans and rice were significantly lower than their leaf values. The value for rice (polished) was 0.002. Iodine was found to be evaporated from the soil-plant system as CH{sub 3}I. The emission of CH{sub 3}I from rice plants grown on flooded soil was much higher than that from oat plants grown on unflooded soil. The {sup 129}I levels in environmental samples collected in and around Tokai-mura, where a spent nuclear fuel reprocessing plant is located, have been determined by neutron activation analysis. The concentrations of {sup 129}I in surface soils ranged from <0.001 to 0.18 Bq kg{sup -1}. The {sup 129}I concentrations in forest soil tended to be higher than those in field soils. (Abstract Truncated)

  11. Insight into Generation and Evolution of Sea-Salt Aerosols from Field Measurements in Diversified Marine and Coastal Atmospheres

    Science.gov (United States)

    Feng, Limin; Shen, Hengqing; Zhu, Yujiao; Gao, Huiwang; Yao, Xiaohong

    2017-01-01

    This report focuses on studying generation and/or evolution of sea-salt aerosols (SSA) on basis of measurements in the Northwest Pacific Ocean (NWPO), the marginal seas of China, at sea-beach sites and a semi-urban coastal site in 2012–2015. From measurements in the NWPO, we obtained the smallest generation function of the super-micron SSA mass ([MSSA]) by the local wind comparing to those previously reported. Vessel-caused wave-breaking was found to greatly enhance generation of SSA and increase [MSSA], which was subject to non-natural generation of SSA. However, naturally enhanced generation of SSA was indeed observed in the marginal seas and at the sea-beach site. The two enhancement mechanisms may explain the difference among this and previous studies. Size distributions of super-micron SSA exhibited two modes, i.e., 1–2 μm mode and ~5 μm mode. The 1–2 μm mode of SSA was enhanced more and comparable to the ~5 μm mode under the wind speed >7 m/s. However, the smaller mode SSA was largely reduced from open oceans to sea-beach sites with reducing wind speed. The two super-micron modes were comparable again at a semi-urban coastal site, suggesting that the smaller super-micron mode SSA may play more important roles in atmospheres.

  12. Solar electric power generation photovoltaic energy systems

    CERN Document Server

    Krauter, Stefan CW

    2007-01-01

    Solar electricity is a viable, environmentally sustainable alternative to the world's energy supplies. In support, this work examines the various technical parameters of photovoltaic systems. It analyzes the study of performance and yield (including optical, thermal, and electrical parameters and interfaces).

  13. Characteristics in the jet region of helium radio-frequency atmospheric-pressure glow discharge with array generators

    Directory of Open Access Journals (Sweden)

    Zhi-Bin Wang

    2015-09-01

    Full Text Available The two-dimensional spatially extended atmospheric plasma arrays by many parallel radio-frequency glow discharge plasma jets packed densely, represent a feature option of large-scale low-temperature atmospheric plasma technologies with distinct capability of directed delivery of reactive species and good insusceptibility to sample variations. However, it is still a challenge to form plasma jet with large area of uniform active species on a downstream substrate due to the complex interactions between individual jets. This paper proposes to numerically study the strategy and mechanism of control/modulation for the array discharge to produce two-dimensional plasma uniformity in the downstream working area. In this work, a two dimensional fluid model is employed to investigate the characteristics in the jet region of helium radio-frequency atmospheric-pressure glow discharge (RF APGD with array generators. The influences of upstream discharge characteristics, gas flow and their cooperative effects on the distribution of species densities, gas temperatures and the uniformity of active species in the material treating area is studied, and the essential strategy for the modulation method is acquired. The results will be significant for deep understanding of coupling behaviors of multiple plasma plumes in the RF APGD array and applications of the technology.

  14. Optimization of Multibrid Permanent-Magnet Wind Generator Systems

    DEFF Research Database (Denmark)

    Chen, Zhe; Li, H.; Polinder, H.

    2009-01-01

    This paper investigates the cost-effective ranges of gearbox ratios and power ratings of multibrid permanent-magnet (PM) wind generator systems by using a design optimization method. First, the analytical model of a multibrid wind turbine concept consisting of a single-stage gearbox and a three......-phase radial-flux PM synchronous generator with a back-to-back power converter is presented. The design optimization is adopted with a genetic algorithm forminimizing generator system cost. To demonstrate the effectiveness of the developed electromagnetic design model, the optimization results of a 500-k......W direct-drive PM generator and a 1.5-MW multibrid PM generator with various gear ratios are, respectively, compared with those from other methods. Then, the optimal design approach is further employed for a range from 750 kW up to 10 MW. The optimization results of PM generator systems including direct...

  15. Synchronization Methods for Three Phase Distributed Power Generation Systems

    DEFF Research Database (Denmark)

    Timbus, Adrian Vasile; Teodorescu, Remus; Blaabjerg, Frede

    2005-01-01

    Nowadays, it is a general trend to increase the electricity production using Distributed Power Generation Systems (DPGS) based on renewable energy resources such as wind, sun or hydrogen. If these systems are not properly controlled, their connection to the utility network can generate problems...... on the grid side. Therefore, considerations about power generation, safe running and grid synchronization must be done before connecting these systems to the utility network. This paper is mainly dealing with the grid synchronization issues of distributed systems. An overview of the synchronization methods...

  16. Pseudo-Random Sequences Generator Based on Discrete Hyperchaotic Systems

    Institute of Scientific and Technical Information of China (English)

    李昌刚; 韩正之

    2003-01-01

    We first design a discrete hyperchaotic system via piecewise linear state feedback. The states of the closed loop system are locally expanding in two directions but absolutely bounded on the whole, which implies hyperchaos. Then, we use three suchlike hyperchaotie systems with different feedback gain matrices to design a pseudo-random sequence generator (PRSG). Through a threshold function, three sub-sequences generated from the output of piecewise linear functions are changed into 0-1 sequences. Then, followed by XOR operation, an unpredictable pseudo-random sequence (PRS) is ultimately obtained. The analysis and simulation results indicate that the PRS, generated with hyperchaotic systems, has desirable statistical features.

  17. Next generation intelligent environments ambient adaptive systems

    CERN Document Server

    Nothdurft, Florian; Heinroth, Tobias; Minker, Wolfgang

    2016-01-01

    This book covers key topics in the field of intelligent ambient adaptive systems. It focuses on the results worked out within the framework of the ATRACO (Adaptive and TRusted Ambient eCOlogies) project. The theoretical background, the developed prototypes, and the evaluated results form a fertile ground useful for the broad intelligent environments scientific community as well as for industrial interest groups. The new edition provides: Chapter authors comment on their work on ATRACO with final remarks as viewed in retrospective Each chapter has been updated with follow-up work emerging from ATRACO An extensive introduction to state-of-the-art statistical dialog management for intelligent environments Approaches are introduced on how Trust is reflected during the dialog with the system.

  18. Next Generation Radio Astronomy Receiver Systems

    CERN Document Server

    Morgan, Matthew A

    2009-01-01

    Radio astronomy observations in the coming decade will require new levels of sensitivity while mapping large regions of space with much greater efficiency than is achieved with current telescopes. This requires new instrumentation with the greatest achievable sensitivity, dynamic range, and field of view. Receiver noise is quickly approaching fundamental limits at most radio wavelengths, so significant gains in sensitivity can only be made by increasing collecting area. Jointly, these requirements suggest using large arrays of smaller antennas, or many moderate-size antennas equipped with multi-beam arrays. The challenge is to develop receivers and wide bandwidth data transport systems which are lower cost, more compact, more reliable, lower weight, and more reproducible than the best current systems, with no compromise to performance. This can be achieved with a greater degree of component integration, extensive use of digital signal processing and transport, and replacement of functions currently performed ...

  19. Options for Next Generation Digital Acquisition Systems

    CERN Document Server

    Boccardi, A

    2011-01-01

    Digital acquisition system designers have an always increasing number of options in terms of bus standards and digital signal processing hardware among which to choose. This allows for high flexibility but also opens the door to a proliferation of different architectures, potentially limiting the reusability and the design synergies among the various instrumentation groups. This contribution illustrates the design trends in some of the major institutes around the world with design examples including VME, PCI and TCA based modular systems using AMC and/or FMC mezzanines. Some examples of FPGA design practices aimed at increasing reusability of code will be mentioned together with some of the tools already available to designers to improve the information exchange and collaboration, like the Open Hardware Repository project.

  20. Prometheus: a next-generation monitoring system

    CERN Document Server

    CERN. Geneva

    2017-01-01

    Prometheus is an open eco-system that provides an end-to-end approach to infrastructure and application monitoring. It covers all levels beginning with easy instrumentation based on a flexible, multi-dimensional data model. The Prometheus server itself collects and stores time series while trying to maintain operational simplicity while being adaptable to varying scales and layouts of infrastructure. By integrating with a wide range of service discovery systems, it always stays in sync with the world it is monitoring. The powerful query language allows us to ask complex questions and can be applied seamlessly between ad-hoc investigation and static dashboarding. It is also directly applied in the eco-system's alerting layer, which favors a time-series based over and event driven approach. In this talk we will look at all aspects of Prometheus from the high-level philosophy behind its design to its practical concerns of implementation and operation. About the speaker Fabian Reinartz is a software eng...

  1. Structure and dynamics of decadal anomalies in the wintertime midlatitude North Pacific ocean-atmosphere system

    Science.gov (United States)

    Fang, Jiabei; Yang, Xiu-Qun

    2016-09-01

    The structure and dynamics of decadal anomalies in the wintertime midlatitude North Pacific ocean-atmosphere system are examined in this study, using the NCEP/NCAR atmospheric reanalysis, HadISST SST and Simple Ocean Data Assimilation data for 1960-2010. The midlatitude decadal anomalies associated with the Pacific Decadal Oscillation are identified, being characterized by an equivalent barotropic atmospheric low (high) pressure over a cold (warm) oceanic surface. Such a unique configuration of decadal anomalies can be maintained by an unstable ocean-atmosphere interaction mechanism in the midlatitudes, which is hypothesized as follows. Associated with a warm PDO phase, an initial midlatitude surface westerly anomaly accompanied with intensified Aleutian low tends to force a negative SST anomaly by increasing upward surface heat fluxes and driving southward Ekman current anomaly. The SST cooling tends to increase the meridional SST gradient, thus enhancing the subtropical oceanic front. As an adjustment of the atmospheric boundary layer to the enhanced oceanic front, the low-level atmospheric meridional temperature gradient and thus the low-level atmospheric baroclinicity tend to be strengthened, inducing more active transient eddy activities that increase transient eddy vorticity forcing. The vorticity forcing that dominates the total atmospheric forcing tends to produce an equivalent barotropic atmospheric low pressure north of the initial westerly anomaly, intensifying the initial anomalies of the midlatitude surface westerly and Aleutian low. Therefore, it is suggested that the midlatitude ocean-atmosphere interaction can provide a positive feedback mechanism for the development of initial anomaly, in which the oceanic front and the atmospheric transient eddy are the indispensable ingredients. Such a positive ocean-atmosphere feedback mechanism is fundamentally responsible for the observed decadal anomalies in the midlatitude North Pacific ocean-atmosphere

  2. Culinary and pressure irrigation water system hydroelectric generation

    Energy Technology Data Exchange (ETDEWEB)

    Christiansen, Cory [Water Works Engineers, Pleasant Grove City, UT (United States)

    2016-01-29

    Pleasant Grove City owns and operates a drinking water system that included pressure reducing stations (PRVs) in various locations and flow conditions. Several of these station are suitable for power generation. The City evaluated their system to identify opportunities for power generation that can be implemented based on the analysis of costs and prediction of power generation and associated revenue. The evaluation led to the selection of the Battle Creek site for development of a hydro-electric power generating system. The Battle Creek site includes a pipeline that carries spring water to storage tanks. The system utilizes a PRV to reduce pressure before the water is introduced into the tanks. The evaluation recommended that the PRV at this location be replaced with a turbine for the generation of electricity. The system will be connected to the utility power grid for use in the community. A pelton turbine was selected for the site, and a turbine building and piping system were constructed to complete a fully functional power generation system. It is anticipated that the system will generate approximately 440,000 kW-hr per year resulting in $40,000 of annual revenue.

  3. Generation of atmospheric boundary layer in the IIUM low speed wind tunnel

    Science.gov (United States)

    Za'aba, Khalid Aldin Bin; Asrar, Waqar; Dheeb, Mohamad Al

    2017-03-01

    The purpose of this paper is to describe an attempt made to simulate the atmospheric boundary layer (ABL) in the Low Speed Wind Tunnel (LSWT) at IIUM. This was performed through modifications of the inlet and surface conditions of the test section. Devices such as spires, fences and surface roughness were used. The ASCE 7-10 standard was used as a reference to validate the results between the wind tunnel data and the full-scale ABL flow characteristics. The velocity profile and turbulence intensity were measured using a one-dimensional hotwire (CTA) probe. The data obtained show good agreement with ASCE 7-10 velocity profiles for exposures B and C while using a scale of 1:488 to match the wind tunnel data. The turbulence intensity profiles do not show a good agreement.

  4. Cold Atmospheric Plasma Generated in Water and its Potential Use in Cancer Therapy

    CERN Document Server

    Chen, Zhitong; Lin, Li; Keidar, Michael

    2016-01-01

    Cold atmospheric plasma (CAP) has been emerged as a novel technology for cancer treatment. CAP can directly treat cells and tissue but such direct application is limited to skin or can be invoked as a supplement during open surgery. In this letter we report indirect plasma treatment using CAP produced in a water using three gases as carrier (argon, helium and nitrogen). Plasma stimulated water was applied to human breast cancer cell line (MDA-MB-231). MTT assays tests showed that using argon plasma had the strongest effect on inducing apoptosis in cultured human breast cancer cells. This result is attributed to the elevated production of the reactive oxygen species and reactive nitrogen species in water in the case of argon plasma.

  5. The Research on Atmospheric Pressure Water Vapour Plasma Generation and Application for the Destruction of Wastes

    Directory of Open Access Journals (Sweden)

    Viktorija Grigaitiene

    2013-01-01

    Full Text Available In the Lithuanian Energy Institute an experimental atmospheric pressure Ar/water vapour plasma torch has been designed and tested. The power of plasma torch was estimated 40 ÷ 69 kW, the mean temperature of plasma jet at the exhaust nozzle was 2300÷2900K. The chemical compositionof water vapour plasma was established from the emission spectrum lines at 300 ÷ 800nm range. The main species observed in Ar/water vapour plasma were: Ar, OH, H, O, Cu. The experiments on water vapour steam reforming were performed. The results confirmed that water vapour plasma has the unique properties – high enthalpy and environmentally friendly conditions. It could be employed for environmental purposes such as destruction of wastes into simple molecules or conversion to synthetic gas.

  6. Numerical experiments on consistent horizontal and vertical resolution for atmospheric models and observing systems

    Science.gov (United States)

    Fox-Rabinovitz, Michael S.; Lindzen, Richard S.

    1993-01-01

    Simple numerical experiments are performed in order to determine the effects of inconsistent combinations of horizontal and vertical resolution in both atmospheric models and observing systems. In both cases, we find that inconsistent spatial resolution is associated with enhanced noise generation. A rather fine horizontal resolution in a satellite-data observing system seems to be excessive when combined with the usually available relatively coarse vertical resolution. Using horizontal filters of different strengths, adjusted in such a way as to render the effective horizontal resolution more consistent with vertical resolution for the observing system, may result in improvement of the analysis accuracy. The increase of vertical resolution for a satellite data observing system with better vertically resolved data, the results are different in that little or no horizontal filtering is needed to make spatial resolution more consistent for the system. The obtained experimental estimates of consistent vertical and effective horizontal resolution are in a general agreement with consistent resolution estimates previously derived theoretically by the authors.

  7. Third-generation percutaneous vertebral augmentation systems

    Science.gov (United States)

    Galzio, Renato; Kazakova, Anna; Pantalone, Andrea; Grillea, Giovanni; Bartolo, Marcello; Salini, Vincenzo; Magliani, Vincenzo

    2016-01-01

    Currently, there is no general consensus about the management of osteoporotic vertebral fractures (OVF). In the past, conservative treatment for at least one month was deemed appropriate for the majority of vertebral fractures. When pain persisted after conservative treatment, it was necessary to consider surgical interventions including: vertebroplasty for vertebral fractures with less than 30% loss of height of the affected vertebral body and kyphoplasty for vertebral fractures with greater than 30% loss of height. Currently, this type of treatment is not feasible. Herein we review the characteristics and methods of operation of three of the most common percutaneous vertebral augmentation systems (PVAS) for the treatment of OVF: Vertebral Body Stenting® (VBS), OsseoFix® and Spine Jack®. VBS is a titanium device accompanied by a hydraulic (as opposed to mechanical) working system which allows a partial and not immediate possibility to control the opening of the device. On the other hand, OsseoFix® and Spine Jack® are accompanied by a mechanical working system which allows a progressive and controlled reduction of the vertebral fracture. Another important aspect to consider is the vertebral body height recovery. OsseoFix® has an indirect mechanism of action: the compaction of the trabecular bone causes an increase in the vertebral body height. Unlike the Vertebral Body Stenting® and Spine Jack®, the OsseoFix® has no direct lift mechanism. Therefore, for these characteristics and for the force that this device is able to provide. In our opinion, Spine Jack® is the only device also suitable for the treatment OVF, traumatic fracture (recent, old or inveterate) and primary or secondary bone tumors. PMID:27683690

  8. Distributed Power-Generation Systems and Protection

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Yang, Yongheng; Yang, Dongsheng

    2017-01-01

    penetration degree of renewable energy, among which wind and solar photovoltaics are typical sources. The integration level of the DPGS into the grid plays a critical role in developing sustainable and resilient power systems, especially with highly intermittent renewable energy resources. To address...... for the DPGS to consolidate the integration. In light of the above, this paper reviews the power-conversion and control technologies used for DPGSs. The impacts of the DPGS on the distributed grid are also examined, and more importantly, strategies for enhancing the connection and protection of the DPGS...

  9. VALIDATION OF SEVERAL ATMOSPHERIC STABILITY INDICES FOR THE STORMS GENERATING TORRENTIAL RAIN SHOWERS IN THE NORTH-WEST OF ROMANIA

    Directory of Open Access Journals (Sweden)

    I. HAIDU

    2014-06-01

    Full Text Available Validation of Several Atmospheric Stability Indices for the Storms Generating Torrential Rain Showers in the North-West of Romania. The present study deals with the atmospheric instability types that lead to torrential rain formation in the North-Western part of Romania and with the role that certain stability indices play in establishing the atmospheric instability potential. 35 years of warm season rainfall data from 14 meteorological stations in the North-West of Romania have been analysed in this respect. The Hellman criterion was employed in order to establish the torrential character of the rainfall events, having made use of 271 of such rainfall events in the analysed period (1975-2009. Considering that the synoptic context of the torrential rain occurrence differs according to the instability type existing at the moment of their apparition, the analysis of the stability indices has taken this feature into consideration as well. Hence, three types of instability have been identified (convective lifting, frontal lifting and that produced due to the “cut off” nuclei their analysis underlining the highest frequency of torrential rains caused by the convective lifting (49.1%, followed by the frontal type (27.7% and the ‘cut off” type (23.2%, their highest percentage being registered in the summer. The values of 5 stability indices have been taken into account (KI, VT, CT, TTI and LI, determined on the basis of the aerologic survey at 00 GMT time, undertaken in Cluj-Napoca, plus two more modified indices (KMOD and TTMOD. Having analysed them, it was possible to identify the most useful ones for determining the convective storms conditions generating torrential rains in the North-West region of Romania.

  10. FEM Simulation of Small Wind Power Generating System Using PMSG

    Science.gov (United States)

    Kesamaru, Katsumi; Ohno, Yoshihiro; Sonoda, Daisuke

    The paper describes a new approach to simulate the small wind power generating systems using PMSG, in which the output is connected to constant resistive load, such as heaters, through the rectifier and the dc chopper. The dynamics of the wind power generating system is presented, and it is shown by simulation results that this approach is useful for system dynamics, such as starting phenomena.

  11. Fractional-order Systems and Synchronous Generator Voltage Regulator

    OpenAIRE

    2015-01-01

    Modern regulators of synchronous generators, including voltage regulators, are digital systems, in their vast majority with standard structures contained in the IEEE standard. These are systems described with stationary differential equations of integral order. Differential equations of fractional order are not employed in regulators for synchronous generator control. This paper presents an analysis of the possibilities of using a system of fractional differential equations in the volta...

  12. Giant Planets of Our Solar System Atmospheres, Composition, and Structure

    CERN Document Server

    Irwin, Patrick G. J

    2009-01-01

    This book reviews the current state of knowledge of the atmospheres of the giant gaseous planets: Jupiter, Saturn, Uranus, and Neptune. The current theories of their formation are reviewed and their recently observed temperature, composition and cloud structures are contrasted and compared with simple thermodynamic, radiative transfer and dynamical models. The instruments and techniques that have been used to remotely measure their atmospheric properties are also reviewed, and the likely development of outer planet observations over the next two decades is outlined. This second edition has been extensively updated following the Cassini mission results for Jupiter/Saturn and the newest ground-based measurements for Uranus/Neptune as well as on the latest development in the theories on planet formation.

  13. Development of Atmospheric Monitoring System for Auger North

    Science.gov (United States)

    Claus, John; Allen, Clint; Botts, Adam; Carande, Bryce; Calhoun, Mike; Emmert, Lucas; Hamilton, Levi; Heid, T. J.; Koop, John; Morgan, Sarah; Robinson, Shay; Sherman, John; Wiencke, Lawrence

    2009-10-01

    The Pierre Auger Northern Fluorescence Detector will measure air-showers over distances of 40 km. Vertical Aerosol profile of the atmosphere at the Pierre Auger Northern site will be measured using the side-scatter method over the 40 km baseline. An atmospheric monitoring telescope (AMT) will use a 3.5 m^2 mirror optimized for UV reflection to focus light from a laser onto a cluster of phototmultiplier tubes. The AMT has been built and final testing and modifications are being carried out before its installation later this year. A remotely programmed, 355 nm YAG laser with a final beam energy of 5 mJ is being used. The automation of the laser and the AMT is controlled via a single board computer (SBC). This talk will present an overview of this R&D program.

  14. Transient Current Analysis of Induction Generators for Wind Power Generating System

    Science.gov (United States)

    Senjyu, Tomonobu; Sueyoshi, Norihide; Uezato, Katsumi; Fujita, Hideki

    In recent year, non-conventional energy generation is coming up for effective use of natural energy, such as wind energy. Induction generators consisting squirrel-cage rotors are widly used as wind generators because of their salient features like robust rotor design, simple in the construction, maintenance free operation, etc. However these induction generators will draw large transient inrush current, several times as large as the machine rated current, the instant when they are connected to utility grid or restored after the fault clearance. Under such situations, there will be a severe voltage fluctuations in the power system. In this paper, we present transient analysis of induction generators before and after a three-phase fault conditions. Theoretical discission is developed to determine the initial phase angle and the time at which maximum transient currents flow in the system.

  15. Properties of atmospheric humic-like substances – water system

    Directory of Open Access Journals (Sweden)

    G. Láng

    2008-02-01

    Full Text Available Urban-type PM2.5-fraction aerosol samples were collected and samples of pure atmospheric humic-like substances (HULIS were isolated from them. Atmospheric concentrations of organic carbon (OC, water soluble organic carbon (WSOC and HULIS were determined, and UV/Vis spectroscopic properties, solubility and conductivity of HULIS in aqueous samples were investigated. Mean atmospheric concentrations of OC and WSOC were 8.5 and 4.6 μg m−3, respectively. Hydrophilic WSOC accounted for 39% of WSOC, carbon in HULIS made up 47% of WSOC, and 14% of WSOC was retained on the separation column by irreversible adsorption. Average molecular mass and aromatic carbon abundance of HULIS were both estimated from molar absorptivity to be 556 Da and 12%, respectively. Both results are substantially smaller than for standard reference fulvic acids, which imply different mechanisms for the formation processes of atmospheric HULIS and aquatic or terrestrial humic matter. HULIS were found to be water soluble as ionic unimers with a saturation concentration of 2–3 g l−1. Their solubility increased again with total HULIS concentration being above approximately 4 g l−1, which was most likely explained by the formation of HULIS aggregates. Solubility increased linearly from approximately 5 up to 20 g l−1 of dissolved HULIS concentration. The ionic dissolution was confirmed by electrochemical conductivity in the investigated concentration interval. Limiting molar conductivity was extrapolated and this was utilized to determine the apparent dissociation degree of HULIS for different concentrations. The dissociation degree was further applied to derive the concentration dependence of the van't Hoff factor of HULIS. The van't Hoff factor decreased monotonically with HULIS concentration; the decrease was substantial for dilute solutions and the relationship became weak for rather concentrated solutions.

  16. Properties of atmospheric humic-like substances ─ water system

    Directory of Open Access Journals (Sweden)

    G. G. Láng

    2008-04-01

    Full Text Available Urban-type PM2.5-fraction aerosol samples were collected and samples of pure atmospheric humic-like substances (HULIS were isolated from them. Atmospheric concentrations of organic carbon (OC, water soluble organic carbon (WSOC and HULIS were determined, and UV/Vis spectroscopic properties, solubility and conductivity of HULIS in aqueous samples were investigated. Atmospheric concentrations of OC and WSOC were 8.5 and 4.6 μg m−3, respectively. Hydrophilic WSOC accounted for 39% of WSOC, carbon in HULIS made up 47% of WSOC, and 14% of WSOC was retained on the separation column by irreversible adsorption. Overall average molecular mass and aromatic carbon abundance of HULIS were estimated from molar absorptivity to be 556 Da and 12%, respectively. Both results are substantially smaller than for standard reference fulvic acids, which imply different mechanisms for the formation processes of atmospheric HULIS and aquatic or terrestrial humic matter. HULIS were found to be water soluble as ionic unimers with a saturation concentration of 2–3 g l−1. Their solubility increased again with total HULIS concentration being above approximately 4 g l−1, which was most likely explained by the formation of HULIS aggregates. Solubility increased linearly from approximately 5 up to 20 g l−1 of dissolved HULIS concentration. The ionic dissolution was confirmed by electrochemical conductivity in the investigated concentration interval. Limiting molar conductivity was extrapolated and this was utilized to determine the apparent dissociation degree of HULIS for different concentrations. The dissociation degree was further applied to derive the concentration dependence of the van't Hoff factor of HULIS. The van't Hoff factor decreased monotonically with HULIS concentration; the decrease was substantial for dilute solutions and the relationship became weak for rather concentrated solutions.

  17. Description of atmospheric conditions at the Pierre Auger Observatory using the Global Data Assimilation System (GDAS)

    NARCIS (Netherlands)

    Abreu, P.; Aglietta, M.; Ahlers, M.; Ahn, E. J.; Albuquerque, I. F. M.; Allard, D.; Allekotte, I.; Allen, J.; Allison, P.; Almela, A.; Alvarez Castillo, J.; Alvarez-Muniz, J.; Ambrosio, M.; Aminaei, A.; Anchordoqui, L.; Andringa, S.; Antici'c, T.; Aramo, C.; Arganda, E.; Arqueros, F.; Asorey, H.; Assis, P.; Aublin, J.; Ave, M.; Avenier, M.; Avila, G.; Baecker, T.; Badescu, A. M.; Balzer, M.; Barber, K. B.; Barbosa, A. F.; Bardenet, R.; Barroso, S. L. C.; Baughman, B.; Baeuml, J.; Beatty, J. J.; Becker, B. R.; Becker, K. H.; Belletoile, A.; Bellido, J. A.; BenZvi, S.; Berat, C.; Bertou, X.; Biermann, P. L.; Billoir, P.; Blanco, F.; Blanco, M.; Bleve, C.; Bluemer, H.; Bohacova, M.; Boncioli, D.; Bonifazi, C.; Bonino, R.; Borodai, N.; Brack, J.; Brancus, I.; Brogueira, P.; Brown, W. C.; Bruijn, R.; Buchholz, P.; Bueno, A.; Burton, R. E.; Caballero-Mora, K. S.; Caccianiga, B.; Caramete, L.; Caruso, R.; Castellina, A.; Catalano, O.; Cataldi, G.; Cazon, L.; Cester, R.; Chauvin, J.; Cheng, S. H.; Chiavassa, A.; Chinellato, J. A.; Chirinos Diaz, J.; Chudoba, J.; Clay, R. W.; Coluccia, M. R.; Conceicao, R.; Contreras, F.; Cook, H.; Cooper, M. J.; Coppens, J.; Cordiera, A.; Coutu, S.; Covault, C. E.; Creusota, A.; Criss, A.; Cronin, J.; Curutiu, A.; Dagoret-Campagne, S.; Dallier, R.; Daniel, B.; Dasso, S.; Daumiller, K.; Dawson, B. R.; de Almeida, R. M.; De Domenico, M.; De Donato, C.; de Jong, S. J.; de la Vega, G.; de Mello Junior, W. J. M.; de Mello Neto, J. R. T.; De Mitri, I.; de Souza, V.; de Vries, K. D.; del Peral, L.; del Rio, M.; Deligny, O.; Dembinski, H.; Dhital, N.; Di Giulio, C.; Diaz Castro, M. L.; Diep, P. N.; Diogo, F.; Dobrigkeit, C.; Docters, W.; D'Olivo, J. C.; Dong, P. N.; Dorofeev, A.; dos Anjos, J. C.; Dova, M. T.; D'Urso, D.; Dutan, I.; Ebr, J.; Engel, R.; Erdmann, M.; Escobar, C. O.; Espadanal, J.; Etchegoyen, A.; Luis, P. Facal San; Tapia, I. Fajardo; Falcke, H.; Farrar, G.; Fauth, A. C.; Fazzini, N.; Ferguson, A. P.; Fick, B.; Filevich, A.; Filipcic, A.; Fliescher, S.; Fracchiolla, C. E.; Fraenkel, E. D.; Fratu, O.; Froehlich, U.; Fuchs, B.; Gaior, R.; Gamarra, R. F.; Gambetta, S.; Garcia, B.; Garcia Roca, S. T.; Garcia-Gamez, D.; Garcia-Pinto, D.; Gascon, A.; Gemmeke, H.; Ghia, P. L.; Giaccari, U.; Giller, M.; Glass, H.; Gold, M. S.; Golup, G.; Gomez Albarracin, F.; Gomez Berisso, M.; Gomez Vitale, P. F.; Goncalves, P.; Gonzalez, D.; Gonzalez, J. G.; Gookin, B.; Gorgi, A.; Gouffon, P.; Grashorn, E.; Grebe, S.; Griffith, N.; Grigat, M.; Grillo, A. F.; Guardincerri, Y.; Guarino, F.; Guedes, G. P.; Guzman, A.; Hansen, P.; Harari, D.; Harrison, T. A.; Harton, J. L.; Haungs, A.; Hebbeker, T.; Heck, D.; Herve, A. E.; Hojvat, C.; Hollon, N.; Holmes, V. C.; Homola, P.; Hoerandel, J. R.; Horneffer, A.; Horvath, P.; Hrabovsky, M.; Huber, D.; Huege, T.; Insolia, A.; Ionita, F.; Italiano, A.; Jarne, C.; Jiraskova, S.; Josebachuili, M.; Kadija, K.; Kampert, K. H.; Karhan, P.; Kasper, P.; Kegl, B.; Keilhauer, B.; Keivani, A.; Kelley, J. L.; Kemp, E.; Kieckhafer, R. M.; Klages, H. O.; Kleifges, M.; Kleinfeller, J.; Knapp, J.; Koang, D. -H.; Kotera, K.; Krohm, N.; Kroemer, O.; Kruppke-Hansen, D.; Kuehn, F.; Kuempel, D.; Kulbartz, J. K.; Kunka, N.; La Rosa, G.; Lachaud, C.; LaHurd, D.; Latronico, L.; Lauer, R.; Lautridou, P.; Le Coz, S.; Leao, M. S. A. B.; Lebrun, D.; Lebrun, P.; Leigui de Oliveira, M. A.; Letessier-Selvon, A.; Lhenry-Yvon, I.; Link, K.; Lopez, R.; Lopez Agueera, A.; Louedec, K.; Lozano Bahilo, J.; Lu, L.; Lucero, A.; Ludwig, M.; Lyberis, H.; Maccarone, M. C.; Macolino, C.; Maldera, S.; Mandat, D.; Mantsch, P.; Mariazzi, A. G.; Marin, J.; Marin, V.; Maris, I. C.; Marquez Falcon, H. R.; Marsella, G.; Martello, D.; Martinez, H.; Martinez Bravo, O.; Mathes, H. J.; Matthews, J.; Matthews, J. A. J.; Matthiae, G.; Maurel, D.; Maurizio, D.; Mazur, P. O.; Medina-Tanco, G.; Melissas, M.; Melo, D.; Menichetti, E.; Menshikov, A.; Mertsch, P.; Meurer, C.; Mi'canovi'c, S.; Micheletti, M. I.; Minaya, I. A.; Miramonti, L.; Molina-Bueno, L.; Mollerach, S.; Monasor, M.; Ragaigne, D. Monnier; Montanet, F.; Morales, B.; Morello, C.; Moreno, E.; Moreno, J. C.; Mostafa, M.; Moura, C. A.; Muller, M. A.; Mueller, G.; Muenchmeyer, M.; Mussa, R.; Navarra, G.; Navarro, J. L.; Navas, S.; Necesal, P.; Nellen, L.; Nelles, A.; Neuser, J.; Nhung, P. T.; Niechciol, M.; Niemietz, L.; Nierstenhoefer, N.; Nitz, D.; Nosek, D.; Nozka, L.; Oehlschlaeger, J.; Olinto, A.; Ortiz, M.; Pacheco, N.; Selmi-Dei, D. Pakk; Palatka, M.; Pallotta, J.; Palmieri, N.; Parente, G.; Parizot, E.; Parra, A.; Pastor, S.; Paul, T.; Pech, M.; Pekala, J.; Pelayo, R.; Pepe, I. M.; Perrone, L.; Pesce, R.; Petermann, E.; Petrera, S.; Petrinca, P.; Petrolini, A.; Petrov, Y.; Pfendner, C.; Piegaia, R.; Pierog, T.; Pieroni, P.; Pimenta, M.; Pirronello, V.; Platino, M.; Ponce, V. H.; Pontz, M.; Porcelli, A.; Privitera, P.; Prouza, M.; Quel, E. J.; Querchfeld, S.; Rautenberg, J.; Ravel, O.; Ravignani, D.; Revenu, B.; Ridky, J.; Riggi, S.; Risse, M.; Ristori, P.; Rivera, H.; Rizi, V.; Roberts, J.; Rodrigues de Carvalho, W.; Rodriguez, G.; Martino, J. Rodriguez; Rojo, J. Rodriguez; Rodriguez-Cabo, I.; Rodriguez-Frias, M. D.; Ros, G.; Rosado, J.; Rossler, T.; Roth, M.; Rouille-d'Orfeuil, B.; Roulet, E.; Rovero, A. C.; Ruehle, C.; Saftoiu, A.; Salamida, F.; Salazar, H.; Greus, F. Salesa; Salina, G.; Sanchez, F.; Santo, C. E.; Santos, E.; Santos, E. M.; Sarazin, F.; Sarkar, B.; Sarkar, S.; Sato, R.; Scharf, N.; Scherini, V.; Schieler, H.; Schiffer, P.; Schmidt, A.; Scholten, O.; Schoorlemmer, H.; Schovancova, J.; Schovanek, P.; Schroeder, F.; Schulte, S.; Schuster, D.; Sciutto, S. J.; Scuderi, M.; Segreto, A.; Settimo, M.; Shadkam, A.; Shellard, R. C.; Sidelnik, I.; Sigl, G.; Silva Lopez, H. H.; Sima, O.; 'Smialkowski, A.; Smida, R.; Snow, G. R.; Sommers, P.; Sorokin, J.; Spinka, H.; Squartini, R.; Srivastava, Y. N.; Stanic, S.; Stapleton, J.; Stasielak, J.; Stephan, M.; Stutz, A.; Suarez, F.; Suomijaervi, T.; Supanitsky, A. D.; Susa, T.; Sutherland, M. S.; Swain, J.; Szadkowski, Z.; Szuba, M.; Tapia, A.; Tartare, M.; Tascau, O.; Tavera Ruiz, C. G.; Tcaciuc, R.; Thao, N. T.; Thomas, D.; Tiffenberg, J.; Timmermans, C.; Tkaczyk, W.; Peixoto, C. J. Todero; Toma, G.; Tomankova, L.; Tome, B.; Tonachini, A.; Travnicek, P.; Tridapalli, D. B.; Tristram, G.; Trovato, E.; Tueros, M.; Ulrich, R.; Unger, M.; Urban, M.; Valdes Galicia, J. F.; Valino, I.; Valore, L.; van den Berg, A. M.; Varela, E.; VargasCardenas, B.; Vazquez, J. R.; Veberic, D.; Verzi, V.; Vicha, J.; Videla, M.; Villasenor, L.; Wahlberg, H.; Wahrlich, P.; Wainberg, O.; Walz, D.; Watson, A. A.; Weber, M.; Weidenhaupt, K.; Weindl, A.; Werner, F.; Westerhoff, S.; Whelan, B. J.; Widom, A.; Wieczorek, G.; Wiencke, L.; Wilczynska, B.; Wilczynski, H.; Will, M.; Williams, C.; Winchen, T.; Wommer, M.; Wundheiler, B.; Yamamoto, T.; Yapici, T.; Younk, P.; Yuan, G.; Yushkov, A.; Zamorano, B.; Zas, E.; Zavrtanik, D.; Zavrtanik, M.; Zaw, I.; Zepeda, A.; Zhu, Y.; Silva, M. Zimbres; Ziolkowski, M.; Martin, L.

    2012-01-01

    Atmospheric conditions at the site of a cosmic ray observatory must be known for reconstructing observed extensive air showers. The Global Data Assimilation System (GDAS) is a global atmospheric model predicated on meteorological measurements and numerical weather predictions. GDAS provides altitude

  18. Gaseous toroid around Saturn. [Saturnian ring system for atomic hydrogen trapping in Titan atmospheric model

    Science.gov (United States)

    Mcdonough, T. R.

    1974-01-01

    The trapping of Titan's escaping atmosphere in the Saturnian system by a toroidal ring is discussed. The radius of the toroid is comparable to Titan's orbit, or about ten times larger than the visible rings. Theoretical atmospheric models are formulated that consider Saturn's gravitational attraction and magnetospheric properties in forming this toroid and in protecting toroid particles from direct ionization by solar wind particles.

  19. Description of atmospheric conditions at the Pierre Auger Observatory using the Global Data Assimilation System (GDAS)

    NARCIS (Netherlands)

    Abreu, P.; Aglietta, M.; Ahlers, M.; Ahn, E. J.; Albuquerque, I. F. M.; Allard, D.; Allekotte, I.; Allen, J.; Allison, P.; Almela, A.; Alvarez Castillo, J.; Alvarez-Muniz, J.; Ambrosio, M.; Aminaei, A.; Anchordoqui, L.; Andringa, S.; Antici'c, T.; Aramo, C.; Arganda, E.; Arqueros, F.; Asorey, H.; Assis, P.; Aublin, J.; Ave, M.; Avenier, M.; Avila, G.; Baecker, T.; Badescu, A. M.; Balzer, M.; Barber, K. B.; Barbosa, A. F.; Bardenet, R.; Barroso, S. L. C.; Baughman, B.; Baeuml, J.; Beatty, J. J.; Becker, B. R.; Becker, K. H.; Belletoile, A.; Bellido, J. A.; BenZvi, S.; Berat, C.; Bertou, X.; Biermann, P. L.; Billoir, P.; Blanco, F.; Blanco, M.; Bleve, C.; Bluemer, H.; Bohacova, M.; Boncioli, D.; Bonifazi, C.; Bonino, R.; Borodai, N.; Brack, J.; Brancus, I.; Brogueira, P.; Brown, W. C.; Bruijn, R.; Buchholz, P.; Bueno, A.; Burton, R. E.; Caballero-Mora, K. S.; Caccianiga, B.; Caramete, L.; Caruso, R.; Castellina, A.; Catalano, O.; Cataldi, G.; Cazon, L.; Cester, R.; Chauvin, J.; Cheng, S. H.; Chiavassa, A.; Chinellato, J. A.; Chirinos Diaz, J.; Chudoba, J.; Clay, R. W.; Coluccia, M. R.; Conceicao, R.; Contreras, F.; Cook, H.; Cooper, M. J.; Coppens, J.; Cordiera, A.; Coutu, S.; Covault, C. E.; Creusota, A.; Criss, A.; Cronin, J.; Curutiu, A.; Dagoret-Campagne, S.; Dallier, R.; Daniel, B.; Dasso, S.; Daumiller, K.; Dawson, B. R.; de Almeida, R. M.; De Domenico, M.; De Donato, C.; de Jong, S. J.; de la Vega, G.; de Mello Junior, W. J. M.; de Mello Neto, J. R. T.; De Mitri, I.; de Souza, V.; de Vries, K. D.; del Peral, L.; del Rio, M.; Deligny, O.; Dembinski, H.; Dhital, N.; Di Giulio, C.; Diaz Castro, M. L.; Diep, P. N.; Diogo, F.; Dobrigkeit, C.; Docters, W.; D'Olivo, J. C.; Dong, P. N.; Dorofeev, A.; dos Anjos, J. C.; Dova, M. T.; D'Urso, D.; Dutan, I.; Ebr, J.; Engel, R.; Erdmann, M.; Escobar, C. O.; Espadanal, J.; Etchegoyen, A.; Luis, P. Facal San; Tapia, I. Fajardo; Falcke, H.; Farrar, G.; Fauth, A. C.; Fazzini, N.; Ferguson, A. P.; Fick, B.; Filevich, A.; Filipcic, A.; Fliescher, S.; Fracchiolla, C. E.; Fraenkel, E. D.; Fratu, O.; Froehlich, U.; Fuchs, B.; Gaior, R.; Gamarra, R. F.; Gambetta, S.; Garcia, B.; Garcia Roca, S. T.; Garcia-Gamez, D.; Garcia-Pinto, D.; Gascon, A.; Gemmeke, H.; Ghia, P. L.; Giaccari, U.; Giller, M.; Glass, H.; Gold, M. S.; Golup, G.; Gomez Albarracin, F.; Gomez Berisso, M.; Gomez Vitale, P. F.; Goncalves, P.; Gonzalez, D.; Gonzalez, J. G.; Gookin, B.; Gorgi, A.; Gouffon, P.; Grashorn, E.; Grebe, S.; Griffith, N.; Grigat, M.; Grillo, A. F.; Guardincerri, Y.; Guarino, F.; Guedes, G. P.; Guzman, A.; Hansen, P.; Harari, D.; Harrison, T. A.; Harton, J. L.; Haungs, A.; Hebbeker, T.; Heck, D.; Herve, A. E.; Hojvat, C.; Hollon, N.; Holmes, V. C.; Homola, P.; Hoerandel, J. R.; Horneffer, A.; Horvath, P.; Hrabovsky, M.; Huber, D.; Huege, T.; Insolia, A.; Ionita, F.; Italiano, A.; Jarne, C.; Jiraskova, S.; Josebachuili, M.; Kadija, K.; Kampert, K. H.; Karhan, P.; Kasper, P.; Kegl, B.; Keilhauer, B.; Keivani, A.; Kelley, J. L.; Kemp, E.; Kieckhafer, R. M.; Klages, H. O.; Kleifges, M.; Kleinfeller, J.; Knapp, J.; Koang, D. -H.; Kotera, K.; Krohm, N.; Kroemer, O.; Kruppke-Hansen, D.; Kuehn, F.; Kuempel, D.; Kulbartz, J. K.; Kunka, N.; La Rosa, G.; Lachaud, C.; LaHurd, D.; Latronico, L.; Lauer, R.; Lautridou, P.; Le Coz, S.; Leao, M. S. A. B.; Lebrun, D.; Lebrun, P.; Leigui de Oliveira, M. A.; Letessier-Selvon, A.; Lhenry-Yvon, I.; Link, K.; Lopez, R.; Lopez Agueera, A.; Louedec, K.; Lozano Bahilo, J.; Lu, L.; Lucero, A.; Ludwig, M.; Lyberis, H.; Maccarone, M. C.; Macolino, C.; Maldera, S.; Mandat, D.; Mantsch, P.; Mariazzi, A. G.; Marin, J.; Marin, V.; Maris, I. C.; Marquez Falcon, H. R.; Marsella, G.; Martello, D.; Martinez, H.; Martinez Bravo, O.; Mathes, H. J.; Matthews, J.; Matthews, J. A. J.; Matthiae, G.; Maurel, D.; Maurizio, D.; Mazur, P. O.; Medina-Tanco, G.; Melissas, M.; Melo, D.; Menichetti, E.; Menshikov, A.; Mertsch, P.; Meurer, C.; Mi'canovi'c, S.; Micheletti, M. I.; Minaya, I. A.; Miramonti, L.; Molina-Bueno, L.; Mollerach, S.; Monasor, M.; Ragaigne, D. Monnier; Montanet, F.; Morales, B.; Morello, C.; Moreno, E.; Moreno, J. C.; Mostafa, M.; Moura, C. A.; Muller, M. A.; Mueller, G.; Muenchmeyer, M.; Mussa, R.; Navarra, G.; Navarro, J. L.; Navas, S.; Necesal, P.; Nellen, L.; Nelles, A.; Neuser, J.; Nhung, P. T.; Niechciol, M.; Niemietz, L.; Nierstenhoefer, N.; Nitz, D.; Nosek, D.; Nozka, L.; Oehlschlaeger, J.; Olinto, A.; Ortiz, M.; Pacheco, N.; Selmi-Dei, D. Pakk; Palatka, M.; Pallotta, J.; Palmieri, N.; Parente, G.; Parizot, E.; Parra, A.; Pastor, S.; Paul, T.; Pech, M.; Pekala, J.; Pelayo, R.; Pepe, I. M.; Perrone, L.; Pesce, R.; Petermann, E.; Petrera, S.; Petrinca, P.; Petrolini, A.; Petrov, Y.; Pfendner, C.; Piegaia, R.; Pierog, T.; Pieroni, P.; Pimenta, M.; Pirronello, V.; Platino, M.; Ponce, V. H.; Pontz, M.; Porcelli, A.; Privitera, P.; Prouza, M.; Quel, E. J.; Querchfeld, S.; Rautenberg, J.; Ravel, O.; Ravignani, D.; Revenu, B.; Ridky, J.; Riggi, S.; Risse, M.; Ristori, P.; Rivera, H.; Rizi, V.; Roberts, J.; Rodrigues de Carvalho, W.; Rodriguez, G.; Martino, J. Rodriguez; Rojo, J. Rodriguez; Rodriguez-Cabo, I.; Rodriguez-Frias, M. D.; Ros, G.; Rosado, J.; Rossler, T.; Roth, M.; Rouille-d'Orfeuil, B.; Roulet, E.; Rovero, A. C.; Ruehle, C.; Saftoiu, A.; Salamida, F.; Salazar, H.; Greus, F. Salesa; Salina, G.; Sanchez, F.; Santo, C. E.; Santos, E.; Santos, E. M.; Sarazin, F.; Sarkar, B.; Sarkar, S.; Sato, R.; Scharf, N.; Scherini, V.; Schieler, H.; Schiffer, P.; Schmidt, A.; Scholten, O.; Schoorlemmer, H.; Schovancova, J.; Schovanek, P.; Schroeder, F.; Schulte, S.; Schuster, D.; Sciutto, S. J.; Scuderi, M.; Segreto, A.; Settimo, M.; Shadkam, A.; Shellard, R. C.; Sidelnik, I.; Sigl, G.; Silva Lopez, H. H.; Sima, O.; 'Smialkowski, A.; Smida, R.; Snow, G. R.; Sommers, P.; Sorokin, J.; Spinka, H.; Squartini, R.; Srivastava, Y. N.; Stanic, S.; Stapleton, J.; Stasielak, J.; Stephan, M.; Stutz, A.; Suarez, F.; Suomijaervi, T.; Supanitsky, A. D.; Susa, T.; Sutherland, M. S.; Swain, J.; Szadkowski, Z.; Szuba, M.; Tapia, A.; Tartare, M.; Tascau, O.; Tavera Ruiz, C. G.; Tcaciuc, R.; Thao, N. T.; Thomas, D.; Tiffenberg, J.; Timmermans, C.; Tkaczyk, W.; Peixoto, C. J. Todero; Toma, G.; Tomankova, L.; Tome, B.; Tonachini, A.; Travnicek, P.; Tridapalli, D. B.; Tristram, G.; Trovato, E.; Tueros, M.; Ulrich, R.; Unger, M.; Urban, M.; Valdes Galicia, J. F.; Valino, I.; Valore, L.; van den Berg, A. M.; Varela, E.; VargasCardenas, B.; Vazquez, J. R.; Veberic, D.; Verzi, V.; Vicha, J.; Videla, M.; Villasenor, L.; Wahlberg, H.; Wahrlich, P.; Wainberg, O.; Walz, D.; Watson, A. A.; Weber, M.; Weidenhaupt, K.; Weindl, A.; Werner, F.; Westerhoff, S.; Whelan, B. J.; Widom, A.; Wieczorek, G.; Wiencke, L.; Wilczynska, B.; Wilczynski, H.; Will, M.; Williams, C.; Winchen, T.; Wommer, M.; Wundheiler, B.; Yamamoto, T.; Yapici, T.; Younk, P.; Yuan, G.; Yushkov, A.; Zamorano, B.; Zas, E.; Zavrtanik, D.; Zavrtanik, M.; Zaw, I.; Zepeda, A.; Zhu, Y.; Silva, M. Zimbres; Ziolkowski, M.; Martin, L.

    2012-01-01

    Atmospheric conditions at the site of a cosmic ray observatory must be known for reconstructing observed extensive air showers. The Global Data Assimilation System (GDAS) is a global atmospheric model predicated on meteorological measurements and numerical weather predictions. GDAS provides altitude

  20. Planetary Probe Entry Atmosphere Estimation Using Synthetic Air Data System

    Science.gov (United States)

    Karlgaard, Chris; Schoenenberger, Mark

    2017-01-01

    This paper develops an atmospheric state estimator based on inertial acceleration and angular rate measurements combined with an assumed vehicle aerodynamic model. The approach utilizes the full navigation state of the vehicle (position, velocity, and attitude) to recast the vehicle aerodynamic model to be a function solely of the atmospheric state (density, pressure, and winds). Force and moment measurements are based on vehicle sensed accelerations and angular rates. These measurements are combined with an aerodynamic model and a Kalman-Schmidt filter to estimate the atmospheric conditions. The new method is applied to data from the Mars Science Laboratory mission, which landed the Curiosity rover on the surface of Mars in August 2012. The results of the new estimation algorithm are compared with results from a Flush Air Data Sensing algorithm based on onboard pressure measurements on the vehicle forebody. The comparison indicates that the new proposed estimation method provides estimates consistent with the air data measurements, without the use of pressure measurements. Implications for future missions such as the Mars 2020 entry capsule are described.

  1. Recent advances in the vertical coupling in the Atmosphere-Ionosphere System

    Science.gov (United States)

    Knížová, Petra Koucká; Georgieva, Katya; Ward, William; Yiğit, Erdal

    2015-12-01

    Welcome to this special issue of the Journal of Atmospheric and Solar-Terrestrial Physics, dedicated to the investigation of the coupling phenomena in the neutral Atmosphere-Ionosphere System. This special issue covers processes in the Atmosphere-Ionosphere System that significantly influence and/or rule the coupling within the regions. Earth's atmospheric regions are intricately coupled to one another via various dynamical, chemical, and electrodynamic processes. The coupling effects can be seen on the modulation of the waves from the lower to upper atmosphere as well as from low- to high-latitudes, electrodynamic and compositional changes, and plasma irregularities at different latitudinal regions around the globe due to the varying energy inputs. A special attention is paid to the Mesosphere-Lower Thermosphere region that represents a critical region in various coupling processes between the lower/middle atmosphere and the upper atmosphere/ionosphere since it forms physical processes filter and shape the flux of waves ascending through the mesosphere into the overlying thermosphere. Varying energy inputs from the Sun and from the lower atmosphere is one of the topics. Processes contributing to the vertical coupling in the atmosphere are discussed on theoretical basis and with respect to recent and long-term experimental measurements as well. Solar activity represents an important factor that directly or indirectly modulates the coupling processes.

  2. Atmospheric-pressure plasma jet induces apoptosis involving mitochondria via generation of free radicals.

    Directory of Open Access Journals (Sweden)

    Hak Jun Ahn

    Full Text Available The plasma jet has been proposed as a novel therapeutic method for anticancer treatment. However, its biological effects and mechanism of action remain elusive. Here, we investigated its cell death effects and underlying molecular mechanisms, using air and N₂ plasma jets from a micro nozzle array. Treatment with air or N₂ plasma jets caused apoptotic death in human cervical cancer HeLa cells, simultaneously with depolarization of mitochondrial membrane potential. In addition, the plasma jets were able to generate reactive oxygen species (ROS, which function as surrogate apoptotic signals by targeting the mitochondrial membrane potential. Antioxidants or caspase inhibitors ameliorated the apoptotic cell death induced by the air and N₂ plasma jets, suggesting that the plasma jet may generate ROS as a proapoptotic cue, thus initiating mitochondria-mediated apoptosis. Taken together, our data suggest the potential employment of plasma jets as a novel therapy for cancer.

  3. Atmospheric-pressure plasma jet induces apoptosis involving mitochondria via generation of free radicals.

    Science.gov (United States)

    Ahn, Hak Jun; Kim, Kang Il; Kim, Geunyoung; Moon, Eunpyo; Yang, Sang Sik; Lee, Jong-Soo

    2011-01-01

    The plasma jet has been proposed as a novel therapeutic method for anticancer treatment. However, its biological effects and mechanism of action remain elusive. Here, we investigated its cell death effects and underlying molecular mechanisms, using air and N₂ plasma jets from a micro nozzle array. Treatment with air or N₂ plasma jets caused apoptotic death in human cervical cancer HeLa cells, simultaneously with depolarization of mitochondrial membrane potential. In addition, the plasma jets were able to generate reactive oxygen species (ROS), which function as surrogate apoptotic signals by targeting the mitochondrial membrane potential. Antioxidants or caspase inhibitors ameliorated the apoptotic cell death induced by the air and N₂ plasma jets, suggesting that the plasma jet may generate ROS as a proapoptotic cue, thus initiating mitochondria-mediated apoptosis. Taken together, our data suggest the potential employment of plasma jets as a novel therapy for cancer.

  4. BUILDOUT AND UPGRADE OF CENTRAL EMERGENCY GENERATOR SYSTEM, GENERATOR 3 AND 4 ELECTRICAL INSTALLATION

    Energy Technology Data Exchange (ETDEWEB)

    Gary D. Seifert; G. Shawn West; Kurt S. Myers; Jim Moncur

    2006-07-01

    SECTION 01000—SUMMARY OF WORK PART 1—GENERAL 1.1 SUMMARY The work to be performed under this project consists of providing the labor, equipment, and materials to perform "Buildout and Upgrade of Central Emergency Generator System, Generator 3 and 4 Electrical Installation" for the National Aeronautics and Space Administration at the Dryden Flight Research Center (NASA/DFRC), Edwards, California 93523. All modifications to existing substations and electrical distribution systems are the responsibility of the contractor. It is the contractor’s responsibility to supply a complete and functionally operational system. The work shall be performed in accordance with these specifications and the related drawings. The work of this project is defined by the plans and specifications contained and referenced herein. This work specifically includes but is not limited to the following: Scope of Work - Installation 1. Install all electrical wiring and controls for new generators 3 and 4 to match existing electrical installation for generators 1 and 2 and in accordance with drawings. Contractor shall provide as-built details for electrical installation. 2. Install battery charger systems for new generators 3 and 4 to match existing battery charging equipment and installation for generators 1 and 2. This may require exchange of some battery charger parts already on-hand. Supply power to new battery chargers from panel and breakers as shown on drawings. Utilize existing conduits already routed to generators 3 and 4 to field route the new wiring in the most reasonable way possible. 3. Install electrical wiring for fuel/lube systems for new generators 3 and 4 to match existing installation for generators 1 and 2. Supply power to lube oil heaters and fuel system (day tanks) from panel and breakers as shown on drawings. Utilize existing conduits already routed to generators 3 and 4 to field route the new wiring in the most reasonable way possible. Add any conduits necessary to

  5. Targeting cancer cells with reactive oxygen and nitrogen species generated by atmospheric-pressure air plasma.

    Directory of Open Access Journals (Sweden)

    Hak Jun Ahn

    Full Text Available The plasma jet has been proposed as a novel therapeutic method for cancer. Anticancer activity of plasma has been reported to involve mitochondrial dysfunction. However, what constituents generated by plasma is linked to this anticancer process and its mechanism of action remain unclear. Here, we report that the therapeutic effects of air plasma result from generation of reactive oxygen/nitrogen species (ROS/RNS including H2O2, Ox, OH-, •O2, NOx, leading to depolarization of mitochondrial membrane potential and mitochondrial ROS accumulation. Simultaneously, ROS/RNS activate c-Jun NH2-terminal kinase (JNK and p38 kinase. As a consequence, treatment with air plasma jets induces apoptotic death in human cervical cancer HeLa cells. Pretreatment of the cells with antioxidants, JNK and p38 inhibitors, or JNK and p38 siRNA abrogates the depolarization of mitochondrial membrane potential and impairs the air plasma-induced apoptotic cell death, suggesting that the ROS/RNS generated by plasma trigger signaling pathways involving JNK and p38 and promote mitochondrial perturbation, leading to apoptosis. Therefore, administration of air plasma may be a feasible strategy to eliminate cancer cells.

  6. Advanced Combustion Systems for Next Generation Gas Turbines

    Energy Technology Data Exchange (ETDEWEB)

    Joel Haynes; Jonathan Janssen; Craig Russell; Marcus Huffman

    2006-01-01

    Next generation turbine power plants will require high efficiency gas turbines with higher pressure ratios and turbine inlet temperatures than currently available. These increases in gas turbine cycle conditions will tend to increase NOx emissions. As the desire for higher efficiency drives pressure ratios and turbine inlet temperatures ever higher, gas turbines equipped with both lean premixed combustors and selective catalytic reduction after treatment eventually will be unable to meet the new emission goals of sub-3 ppm NOx. New gas turbine combustors are needed with lower emissions than the current state-of-the-art lean premixed combustors. In this program an advanced combustion system for the next generation of gas turbines is being developed with the goal of reducing combustor NOx emissions by 50% below the state-of-the-art. Dry Low NOx (DLN) technology is the current leader in NOx emission technology, guaranteeing 9 ppm NOx emissions for heavy duty F class gas turbines. This development program is directed at exploring advanced concepts which hold promise for meeting the low emissions targets. The trapped vortex combustor is an advanced concept in combustor design. It has been studied widely for aircraft engine applications because it has demonstrated the ability to maintain a stable flame over a wide range of fuel flow rates. Additionally, it has shown significantly lower NOx emission than a typical aircraft engine combustor and with low CO at the same time. The rapid CO burnout and low NOx production of this combustor made it a strong candidate for investigation. Incremental improvements to the DLN technology have not brought the dramatic improvements that are targeted in this program. A revolutionary combustor design is being explored because it captures many of the critical features needed to significantly reduce emissions. Experimental measurements of the combustor performance at atmospheric conditions were completed in the first phase of the program

  7. Simulation of Variable Speed Wind Generation System Using Boost Converter of Permanent Magnet Synchronous Generator

    Science.gov (United States)

    Ohyama, Kazuhiro; Sakamoto, Tsuyoshi; Arinaga, Shinji; Yamashita, Yukio

    This paper proposes variable-speed wind generation system using the boost converter. The proposed system has three speed control modes for the wind velocity. The control mode of low wind velocity regulates the armature current of the generator with the boost converter to control the speed of wind turbine. The control mode of middle wind velocity regulates the DC link voltage with the vector controlled inverter to control the speed of wind turbine. The control mode of high wind velocity regulates the pitch angle of the wind turbine with the pitch angle control system to control the speed of wind turbine. The hybrid of three control modes extends the variable-speed range. The proposed system simplifies the maintenance and improves the reliability and reduces the cost in compare with the variable-speed wind generation system using PWM converter. This paper describes the control strategy and modeling for simulation using Matlab Simulink of the proposed system. Also this paper describes the control strategy and modeling of variable-speed wind generation system using PWM converter. The steady state and transient responses for wind velocity changes are simulated using the Matlab Simulink. This paper verifies the fundamental performance of the system using boost converter by discussing the simulation results of the both systems.

  8. Application of computational neural networks in predicting atmospheric pollutant concentrations due to fossil-fired electric power generation

    Energy Technology Data Exchange (ETDEWEB)

    El-Hawary, F. [BH Engineering Systems & Technical Univ. of Nova Scotia (Canada)

    1995-12-31

    The ability to accurately predict the behavior of a dynamic system is of essential importance in monitoring and control of complex processes. In this regard recent advances in neural-net based system identification represent a significant step toward development and design of a new generation of control tools for increased system performance and reliability. The enabling functionality is the one of accurate representation of a model of a nonlinear and nonstationary dynamic system. This functionality provides valuable new opportunities including: (1) The ability to predict future system behavior on the basis of actual system observations, (2) On-line evaluation and display of system performance and design of early warning systems, and (3) Controller optimization for improved system performance. In this presentation, we discuss the issues involved in definition and design of learning control systems and their impact on power system control. Several numerical examples are provided for illustrative purpose.

  9. 40 CFR 53.42 - Generation of test atmospheres for wind tunnel tests.

    Science.gov (United States)

    2010-07-01

    ... or better (e.g., hot-wire anemometry). The mean wind speed in the test section of the wind tunnel... section shall be determined during the tests using an appropriate technique (e.g., hot-wire anemometry... volumetric units. (g) Schematic drawings of the particle delivery system (wind tunnel and blower system) and...

  10. Characteristics of atmospheric gravity waves observed using the MU (Middle and Upper atmosphere) radar and GPS (Global Positioning System) radio occultation

    Science.gov (United States)

    TSUDA, Toshitaka

    2014-01-01

    The wind velocity and temperature profiles observed in the middle atmosphere (altitude: 10–100 km) show perturbations resulting from superposition of various atmospheric waves, including atmospheric gravity waves. Atmospheric gravity waves are known to play an important role in determining the general circulation in the middle atmosphere by dynamical stresses caused by gravity wave breaking. In this paper, we summarize the characteristics of atmospheric gravity waves observed using the middle and upper atmosphere (MU) radar in Japan, as well as novel satellite data obtained from global positioning system radio occultation (GPS RO) measurements. In particular, we focus on the behavior of gravity waves in the mesosphere (50–90 km), where considerable gravity wave attenuation occurs. We also report on the global distribution of gravity wave activity in the stratosphere (10–50 km), highlighting various excitation mechanisms such as orographic effects, convection in the tropics, meteorological disturbances, the subtropical jet and the polar night jet. PMID:24492645

  11. Welfare and Generational Equity in Sustainable Unfunded Pension Systems.

    Science.gov (United States)

    Auerbach, Alan J; Lee, Ronald

    2011-02-01

    Using stochastic simulations we analyze how public pension structures spread the risks arising from demographic and economic shocks across generations. We consider several actual and hypothetical sustainable PAYGO pension structures, including: (1) versions of the US Social Security system with annual adjustments of taxes or benefits to maintain fiscal balance; (2) Sweden's Notional Defined Contribution system and several variants developed to improve fiscal stability; and (3) the German system, which also includes annual adjustments to maintain fiscal balance. For each system, we present descriptive measures of uncertainty in representative outcomes for a typical generation and across generations. We then estimate expected utility for generations based on simplifying assumptions and incorporate these expected utility calculations in an overall social welfare measure. Using a horizontal equity index, we also compare the different systems' performance in terms of how neighboring generations are treated.While the actual Swedish system smoothes stochastic fluctuations more than any other and produces the highest degree of horizontal equity, it does so by accumulating a buffer stock of assets that alleviates the need for frequent adjustments. In terms of social welfare, this accumulation of assets leads to a lower average rate of return that more than offsets the benefits of risk reduction, leaving systems with more frequent adjustments that spread risks broadly among generations as those most preferred.

  12. Towards an Explanation Generation System for Robots: Analysis and Recommendations

    Directory of Open Access Journals (Sweden)

    Ben Meadows

    2016-10-01

    Full Text Available A fundamental challenge in robotics is to reason with incomplete domain knowledge to explain unexpected observations and partial descriptions extracted from sensor observations. Existing explanation generation systems draw on ideas that can be mapped to a multidimensional space of system characteristics, defined by distinctions, such as how they represent knowledge and if and how they reason with heuristic guidance. Instances in this multidimensional space corresponding to existing systems do not support all of the desired explanation generation capabilities for robots. We seek to address this limitation by thoroughly understanding the range of explanation generation capabilities and the interplay between the distinctions that characterize them. Towards this objective, this paper first specifies three fundamental distinctions that can be used to characterize many existing explanation generation systems. We explore and understand the effects of these distinctions by comparing the capabilities of two systems that differ substantially along these axes, using execution scenarios involving a robot waiter assisting in seating people and delivering orders in a restaurant. The second part of the paper uses this study to argue that the desired explanation generation capabilities corresponding to these three distinctions can mostly be achieved by exploiting the complementary strengths of the two systems that were explored. This is followed by a discussion of the capabilities related to other major distinctions to provide detailed recommendations for developing an explanation generation system for robots.

  13. System for Automatic Generation of Examination Papers in Discrete Mathematics

    Science.gov (United States)

    Fridenfalk, Mikael

    2013-01-01

    A system was developed for automatic generation of problems and solutions for examinations in a university distance course in discrete mathematics and tested in a pilot experiment involving 200 students. Considering the success of such systems in the past, particularly including automatic assessment, it should not take long before such systems are…

  14. Smart pitch control strategy for wind generation system using doubly fed induction generator

    Science.gov (United States)

    Raza, Syed Ahmed

    A smart pitch control strategy for a variable speed doubly fed wind generation system is presented in this thesis. A complete dynamic model of DFIG system is developed. The model consists of the generator, wind turbine, aerodynamic and the converter system. The strategy proposed includes the use of adaptive neural network to generate optimized controller gains for pitch control. This involves the generation of controller parameters of pitch controller making use of differential evolution intelligent technique. Training of the back propagation neural network has been carried out for the development of an adaptive neural network. This tunes the weights of the network according to the system states in a variable wind speed environment. Four cases have been taken to test the pitch controller which includes step and sinusoidal changes in wind speeds. The step change is composed of both step up and step down changes in wind speeds. The last case makes use of scaled wind data collected from the wind turbine installed at King Fahd University beach front. Simulation studies show that the differential evolution based adaptive neural network is capable of generating the appropriate control to deliver the maximum possible aerodynamic power available from wind to the generator in an efficient manner by minimizing the transients.

  15. The Role of Intraseasonal Atmosphere Variability in ENSO Generation in Future Climate

    Science.gov (United States)

    Matveeva, Tatiana; Gushchina, Daria

    2016-04-01

    The intraseasonal tropical variability (ITV) is a general component of the atmospheric circulation in the tropics, particularly, it plays the main role in the formation of El Niño-Southern Oscillation (ENSO). The ENSO is the general mode of interannual climate variability. It appears in two kinds of large-scale sea surface temperature (SST) anomalies in the equatorial Pacific Ocean: East Pacific (EP) El Niño (named also Canonical El Niño) characterized by anomalous warming in the eastern Pacific, and Central Pacific (CP) El Niño (so-called El Niño Modoki) with maximum SST anomalous in the center of the Pacific Ocean [Kao and Yu, 2009; Kug et al., 2009]. The ability of CMIP5 coupled ocean-atmosphere general circulation models (CGCMs) to simulate two flavors of El Niño is estimated using Empirical orthogonal functions (EOFs) analysis of SST anomalies fields (Experiment Pi-Control), in this study we assessed 20 CGCMs. Spatial distribution of the first mode (EOF 1) represents SST anomalies field structure of EP El Niño and the second mode (EOF 2) is analogue of SST anomalies spatial distribution during CP El Niño [Ashok et al., 2007]. To identify intensity and frequency ENSO we also considered both NINO3 and NINO4 SST indices. NINO3 and NINO4 regions have been defined based on EOF-analysis (EOF 1 and EOF 2, resp.). It's shown that only several models were able to simulate two kinds of ENSO. Then we tested chosen CGCMs' ability to correct simulation of ITV components. For identification ITV components in the tropical troposphere we applied double space-time Fourier analysis to zonal wind at 850 hPa (U850), following the method of WK99 [Wheler and Kiladis, 1999]. Then we defined wave activity and analyzed spatial pattern of the waves and relationship between the waves and ENSO. Besides, it is shown that the ITV characteristics are altered during different flavors of ENSO [Gushchina and Dewitte, 2012]. In [Yeh et al., 2009] it has been established that the ratio

  16. Thin Thermoelectric Generator System for Body Energy Harvesting

    Science.gov (United States)

    Settaluri, Krishna T.; Lo, Hsinyi; Ram, Rajeev J.

    2012-06-01

    Wearable thermoelectric generators (TEGs) harvest thermal energy generated by the body to generate useful electricity. The performance of these systems is limited by (1) the small working temperature differential between the body and ambient, (2) the desire to use natural air convection cooling on the cold side of the generator, and (3) the requirement for thin, lightweight systems that are comfortable for long-term use. Our work has focused on the design of the heat transfer system as part of the overall thermoelectric (TE) system. In particular, the small heat transfer coefficient for natural air convection results in a module thermal impedance that is smaller than that of the heat sink. In this heat-sink-limited regime, the thermal resistance of the generator should be optimized to match that of the heat sink to achieve the best performance. In addition, we have designed flat (1 mm thickness) copper heat spreaders to realize performance surpassing splayed pin heat sinks. Two-dimensional (2-D) heat spreading exploits the large surface area available in a wristband and allows patterned copper to efficiently cool the TE. A direct current (DC)/DC converter is integrated on the wristband. The system generates up to 28.5 μW/cm2 before the converter and 8.6 μW/cm2 after the converter, with 30% efficiency. It generates output of 4.15 V with overall thickness under 5 mm.

  17. Ceramic Oxygen Generator for Carbon Dioxide Electrolysis Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this SBIR Phase I proposal (Topic X9.01), NexTech Materials, Ltd. proposes to develop a high efficiency ceramic oxygen generation system which will separate O2...

  18. Synchronous Chaos Generation in an ^-Doped Fiber Laser System

    National Research Council Canada - National Science Library

    Gomez-Pavon, L. C; Munoz-Pacheco, J. M; Luis-Ramos, A

    2015-01-01

    ...+ -doped fiber lasers is experimentally analyzed. Using a single amplitude modulator in the system, synchronous chaos generation is obtained at two different modulation frequencies, i.e., 10.38 and 3.85 MHz...

  19. Competition and Cooperation of Distributed Generation and Power System

    Science.gov (United States)

    Miyake, Masatoshi; Nanahara, Toshiya

    Advances in distributed generation technologies together with the deregulation of an electric power industry can lead to a massive introduction of distributed generation. Since most of distributed generation will be interconnected to a power system, coordination and competition between distributed generators and large-scale power sources would be a vital issue in realizing a more desirable energy system in the future. This paper analyzes competitions between electric utilities and cogenerators from the viewpoints of economic and energy efficiency based on the simulation results on an energy system including a cogeneration system. First, we examine best response correspondence of an electric utility and a cogenerator with a noncooperative game approach: we obtain a Nash equilibrium point. Secondly, we examine the optimum strategy that attains the highest social surplus and the highest energy efficiency through global optimization.

  20. Advanced On Board Inert Gas Generation System (OBBIGS) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Valcor Engineering Corporation proposes to develop an advanced On Board Inert Gas Generation System, OBIGGS, for aircraft fuel tank inerting to prevent hazardous...

  1. Miniaturized In Situ Atmospheric Probe Sampling Inlet System for Uranus or Saturn Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Thorleaf Research, Inc. proposes to develop a miniaturized in situ atmospheric probe sampling inlet system for measuring chemical and isotopic composition of the...

  2. Cold weather hydrogen generation system and method of operation

    Energy Technology Data Exchange (ETDEWEB)

    Dreier, Ken Wayne (Madison, CT); Kowalski, Michael Thomas (Seymour, CT); Porter, Stephen Charles (Burlington, CT); Chow, Oscar Ken (Simsbury, CT); Borland, Nicholas Paul (Montpelier, VT); Goyette, Stephen Arthur (New Hartford, CT)

    2010-12-14

    A system for providing hydrogen gas is provided. The system includes a hydrogen generator that produces gas from water. One or more heat generation devices are arranged to provide heating of the enclosure during different modes of operation to prevent freezing of components. A plurality of temperature sensors are arranged and coupled to a controller to selectively activate a heat source if the temperature of the component is less than a predetermined temperature.

  3. Cold weather hydrogen generation system and method of operation

    Science.gov (United States)

    Dreier, Ken Wayne; Kowalski, Michael Thomas; Porter, Stephen Charles; Chow, Oscar Ken; Borland, Nicholas Paul; Goyette, Stephen Arthur

    2010-12-14

    A system for providing hydrogen gas is provided. The system includes a hydrogen generator that produces gas from water. One or more heat generation devices are arranged to provide heating of the enclosure during different modes of operation to prevent freezing of components. A plurality of temperature sensors are arranged and coupled to a controller to selectively activate a heat source if the temperature of the component is less than a predetermined temperature.

  4. Intelligent control of energy-saving power generation system

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Zhiyuan; Zhang, Guoqing; Guo, Zhizhong [Harbin Institute of Technology, Harbin (China). Dept. of Electrical Engineering

    2013-07-01

    Highway power generation system which is environmentally friendly and sustainable provides an innovative method of energy conversion. It is also as a kind of city science and technology innovation, which has the characteristics of environmental protection and sustainable utilization. Making full use of vehicle impact speed control humps, we design a new kind of highway speed control humps combined with solar electric generation system integration. Developing green energy, energy saving and environment protection can be achieved.

  5. Recursive Model System for Trip Generation and Trip Chaining

    OpenAIRE

    Goulias, Konstadinos G.; KITAMURA, Ryuichi

    1991-01-01

    A model system is developed to describe both trip generation and trip chaining in a coherent manner. A recursive structure is adopted to represent the generation of trips for different purposes, and the number of trip chains is expressed as a function of the numbers of trips by purpose. The model system offers theoretically consistent coefficient values and quantifies the relationship between the number of trips and the number of trip chains, and can be used in the conventional forecasting pr...

  6. Microwave heating systems for atmospheric pressure: Nonequilibrium plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Guest, G.E.; Dandl, R.A. (AMPC, Inc., Carlsbad, CA (USA))

    1989-03-01

    Nonequilibrium plasma-chemical processing is attracting increasing interest because of the possibility of creating mixtures of active species that would not be available in thermal equilibrium. For significant throughput of reactants it would be advantageous to create nonequilibrium plasmas in large volumes of atmospheric-pressure mixtures of gases. Techniques for accomplishing this are very limited at present. Here they describe a novel microwave approach to creating nonequilibrium plasmas in large volumes of atmospheric-pressure gases using pulses of microwave radiation with very high peak power that are focused by quasi-optical techniques at one or more points in the interior of the reaction chamber. A new type of microwave source, the Plasma Electron Microwave Source (PEMS), is able to produce the require power levels by storing cw microwave power in a mirror-confined, relativistic-electron plasma and periodically transforming a fraction of that stored energy into intense microwave pulses. This approach avoids many of the limitations inherent in resonant cavity approaches and is expected to permit ultrahigh purity discharges to be produced.

  7. Regulation Law of Turbine and Generator in Organic Rankine Cycle Power Generation Experimental System

    Institute of Scientific and Technical Information of China (English)

    潘利生; 王怀信; 史维秀

    2014-01-01

    In the performance experiment of organic Rankine cycle power generation experimental system, the load-resistance-regulation method is one of the most important regulation methods. However, the regulation law has not been clear enough to guide the experiment, which is unfavorable to the experimental research on organic Rankine cy-cle. In this paper the regulation law of turbine and generator by the load-resistance-regulation method is studied theo-retically and experimentally. The results show that when the thermal cycle parameters keep constant, the turbine speed increases with the increase of load resistance and there is a maximum value of transmission-generator efficiency with the variation of the turbine speed; when the turbine speed and generator speed keep constant, the transmission-generator efficiency decreases and gradually tends to zero with the increase of load resistance.

  8. Generators and automated generator systems for production and on-line injections of pet radiopharmaceuticals

    Science.gov (United States)

    Shimchuk, G.; Shimchuk, Gr; Pakhomov, G.; Avalishvili, G.; Zavrazhnov, G.; Polonsky-Byslaev, I.; Fedotov, A.; Polozov, P.

    2017-01-01

    One of the prospective directions of PET development is using generator positron radiating nuclides [1,2]. Introduction of this technology is financially promising, since it does not require expensive special accelerator and radiochemical laboratory in the medical institution, which considerably reduces costs of PET diagnostics and makes it available to more patients. POZITOM-PRO RPC LLC developed and produced an 82Sr-82Rb generator, an automated injection system, designed for automatic and fully-controlled injections of 82RbCl produced by this generator, automated radiopharmaceutical synthesis units based on generated 68Ga produced using a domestically-manufactured 68Ge-68Ga generator for preparing two pharmaceuticals: Ga-68-DOTA-TATE and Vascular Ga-68.

  9. "Method, system and storage medium for generating virtual brick models"

    DEFF Research Database (Denmark)

    2009-01-01

    An exemplary embodiment is a method for generating a virtual brick model. The virtual brick models are generated by users and uploaded to a centralized host system. Users can build virtual models themselves or download and edit another user's virtual brick models while retaining the identity...... of the original virtual brick model. Routines are provided for both storing user created building steps in and generating automated building instructions for virtual brick models, generating a bill of materials for a virtual brick model and ordering physical bricks corresponding to a virtual brick model....

  10. Stabilization of a Power System including Inverter Type Distributed Generators by the Virtual Synchronous Generator

    Science.gov (United States)

    Sakimoto, Kenichi; Miura, Yushi; Ise, Toshifumi

    The capacity of Distributed Generators (DGs) connected to grid by inverters are growing year and year. The inverters are generally controlled by PLL (Phase Locked Loop) in order to synchronize with power system frequency. Power systems will become unstable, if the capacity of inverter type DGs become larger and larger, because inverter frequency is controlled just to follow the frequency decided by other synchronous generators. There is the idea that inverters are controlled to behave like a synchronous generator. This concept is called Virtual Synchronous Generator (VSG). In this paper, a control scheme of VSG is presented, and the design method of required energy storage and the ability of grid stabilizing control by VSG is investigated by computer simulations.

  11. The generation of diesel exhaust particle aerosols from a bulk source in an aerodynamic size range similar to atmospheric particles

    Directory of Open Access Journals (Sweden)

    Daniel J Cooney

    2008-08-01

    Full Text Available Daniel J Cooney1, Anthony J Hickey21Department of Biomedical Engineering; 2School of Pharmacy, University of North Carolina, Chapel Hill, NC, USAAbstract: The influence of diesel exhaust particles (DEP on the lungs and heart is currently a topic of great interest in inhalation toxicology. Epidemiological data and animal studies have implicated airborne particulate matter and DEP in increased morbidity and mortality due to a number of cardiopulmonary diseases including asthma, chronic obstructive pulmonary disorder, and lung cancer. The pathogeneses of these diseases are being studied using animal models and cell culture techniques. Real-time exposures to freshly combusted diesel fuel are complex and require significant infrastructure including engine operations, dilution air, and monitoring and control of gases. A method of generating DEP aerosols from a bulk source in an aerodynamic size range similar to atmospheric DEP would be a desirable and useful alternative. Metered dose inhaler technology was adopted to generate aerosols from suspensions of DEP in the propellant hydrofluoroalkane 134a. Inertial impaction data indicated that the particle size distributions of the generated aerosols were trimodal, with count median aerodynamic diameters less than 100 nm. Scanning electron microscopy of deposited particles showed tightly aggregated particles, as would be expected from an evaporative process. Chemical analysis indicated that there were no major changes in the mass proportion of 2 specific aromatic hydrocarbons (benzo[a]pyrene and benzo[k]fluoranthene in the particles resulting from the aerosolization process.Keywords: diesel exhaust particles, aerosol, inhalation toxicology

  12. Power Quality Improvement of a Distributed Generation Power System

    Directory of Open Access Journals (Sweden)

    Panga Harish

    2016-06-01

    Full Text Available The aim of this work is to improve the power quality for Distributed Generation (DG with power storage system. Power quality is the combination of voltage quality and current quality. Power quality is the set of limits of electrical properties that allows electrical systems to function in their intended manner without significant loss of performance or life. The electrical power quality is more concerned issue. The main problems are stationery and transient distortions in the line voltage such as harmonics, flicker, swells, sags and voltage asymmetries. Distributed Generation (DG also called as site generation, dispersed generation, embedded generation, decentralized generation, decentralized energy or distributed energy, generates electricity from the many small energy sources. In recent years, micro electric power systems such as photovoltaic generation systems, wind generators and micro gas turbines, etc., have increased with the deregulation and liberalization of the power market. Under such circumstances the environment surrounding the electric power industry has become ever more complicated and provides high-quality power in a stable manner which becomes an important topic. Here DG is assumed to include Wind power Generation (WG and Fuel Cells (FC, etc. Advantages of this system are constant power supply, constant voltage magnitude, absence of harmonics insupply voltage, un-interrupted power supply. In this project the electric power qualities in two cases will be compared. Case I: With the storage battery when it is introduced. Case II: Without the storage battery. The storage battery executes the control that maintains the voltage in the power system. It will be found that the Electric power quality will be improved, when storage battery is introduced. The model system used in this Project work is composed of a Wind Turbine, an Induction Generator, Fuel Cells, An Inverter and a Storage Battery. A miniature Wind Power Generator is

  13. Atmospheric Mining in the Outer Solar System:. [Aerial Vehicle Reconnaissance and Exploration Options

    Science.gov (United States)

    Palaszewski, Bryan A.

    2014-01-01

    Atmospheric mining in the outer solar system has been investigated as a means of fuel production for high energy propulsion and power. Fusion fuels such as Helium 3 (3He) and hydrogen can be wrested from the atmospheres of Uranus and Neptune and either returned to Earth or used in-situ for energy production. Helium 3 and hydrogen (deuterium, etc.) were the primary gases of interest with hydrogen being the primary propellant for nuclear thermal solid core and gas core rocket-based atmospheric flight. A series of analyses were undertaken to investigate resource capturing aspects of atmospheric mining in the outer solar system. This included the gas capturing rate, storage options, and different methods of direct use of the captured gases. Additional supporting analyses were conducted to illuminate vehicle sizing and orbital transportation issues. While capturing 3He, large amounts of hydrogen and 4He are produced. With these two additional gases, the potential for fueling small and large fleets of additional exploration and exploitation vehicles exists. Additional aerospacecraft or other aerial vehicles (UAVs, balloons, rockets, etc.) could fly through the outer planet atmospheres, for global weather observations, localized storm or other disturbance investigations, wind speed measurements, polar observations, etc. Deep-diving aircraft (built with the strength to withstand many atmospheres of pressure) powered by the excess hydrogen or helium 4 may be designed to probe the higher density regions of the gas giants. Outer planet atmospheric properties, atmospheric storm data, and mission planning for future outer planet UAVs are presented.

  14. Advanced methodology for generation expansion planning including interconnected systems

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, M.; Yokoyama, R.; Yasuda, K. [Tokyo Metropolitan Univ. (Japan); Sasaki, H. [Hiroshima Univ. (Japan); Ogimoto, K. [Electric Power Development Co. Ltd., Tokyo (Japan)

    1994-12-31

    This paper reviews advanced methodology for generation expansion planning including interconnected systems developed in Japan, putting focus on flexibility and efficiency in a practical application. First, criteria for evaluating flexibility of generation planning considering uncertainties are introduced. Secondly, the flexible generation mix problem is formulated as a multi-objective optimization with more than two objective functions. The multi-objective optimization problem is then transformed into a single objective problem by using the weighting method, to obtain the Pareto optimal solution, and solved by a dynamics programming technique. Thirdly, a new approach for electric generation expansion planning of interconnected systems is presented, based on the Benders Decomposition technique. That is, large scale generation problem constituted by the general economic load dispatch problem, and several sub problems which are composed of smaller scale isolated system generation expansion plans. Finally, the generation expansion plan solved by an artificial neural network is presented. In conclusion, the advantages and disadvantages of this method from the viewpoint of flexibility and applicability to practical generation expansion planning are presented. (author) 29 refs., 10 figs., 4 tabs.

  15. Loss Minimizing Operation of Doubly Fed Induction Generator Based Wind Generation Systems Considering Reactive Power Provision

    DEFF Research Database (Denmark)

    Baohua, Zhang; Hu, Weihao; Chen, Zhe

    2014-01-01

    The paper deals with control techniques for minimizing the operating loss of doubly fed induction generator based wind generation systems when providing reactive power. The proposed method achieves its goal through controlling the rotor side q-axis current in the synchronous reference frame....... The formula for the control reference is explicitly deduced in this paper considering the losses of the generator, the power electronic devices and the filter. Three control strategies are compared with the proposed method under different wind speeds and different reactive power references. The simulation...

  16. Power Electronics for the Next Generation Wind Turbine System

    DEFF Research Database (Denmark)

    Ma, Ke

    The wind power generation has been steadily growing both for the total installed capacity and for the individual turbine size. Due to much more significant impacts to the power grid, the power electronics, which can change the behavior of wind turbines from an unregulated power source to an active...... generation unit, are becoming crucial in the wind turbine system. The objective of this project is to study the power electronics technology used for the next generation wind turbines. Some emerging challenges as well as potentials like the cost of energy and reliability are going to be addressed. First...... better control performance under the unbalanced AC source. It is concluded that power electronics will play more important role and regulate all the generated power in the next generation wind turbine system. In this case, the stress in the converter components becomes more critical because the power...

  17. LMFBR steam generator systems development program progress report

    Energy Technology Data Exchange (ETDEWEB)

    None

    The intent of this program is to investigate methods of producing 2-1/4 Cr-1Mo duplex tubing to meet the structural, thermal/hydraulic and leak detection design requirements of the duplex tube leak detection concept for application on the Demonstration Plant and/or prototype steam generator. The leak detection concept as envisioned for LMFBR steam generator application will be analyzed regarding response to credible leak situations. The results of testing will be used for this analysis. The third fluid system will be conceptually designed including the two plena design adaptations being considered and the advantages and disadvantages of each will be assessed. The test program for the single-tube steam generator model will be developed in accordance with the technical and schedular objectives of the LMFBR duplex tube steam generator development program. A conceptual steam generator configuration will be established for use as a reference in the on-going feasibility studies and Demo Plant system development.

  18. Photovoltaic-wind hybrid autonomous generation systems in Mongolia

    Energy Technology Data Exchange (ETDEWEB)

    Dei, Tsutomu; Ushiyama, Izumi

    2005-01-01

    Two hybrid stand-alone (autonomous) power systems, each with wind and PV generation, were studied as installed at health clinics in semi-desert and mountainous region in Mongolia. Meteorological and system operation parameters, including power output and the consumption of the system, were generally monitored by sophisticated monitoring. However, where wind and solar site information was lacking, justifiable estimates were made. The results show that there is a seasonal complementary relationship between wind and solar irradiation in Tarot Sum. The users understood the necessity of Demand Side Management of isolated wind-PV generation system through technology transfer seminars and actually executed DSM at both sites. (author)

  19. Windfarm Generation Assessment for Reliability Analysis of Power Systems

    DEFF Research Database (Denmark)

    Barberis Negra, Nicola; Bak-Jensen, Birgitte; Holmstrøm, O.

    2007-01-01

    Due to the fast development of wind generation in the past ten years, increasing interest has been paid to techniques for assessing different aspects of power systems with a large amount of installed wind generation. One of these aspects concerns power system reliability. Windfarm modelling plays...... in a reliability model and the generation of a windfarm is evaluated by means of sequential Monte Carlo simulation. Results are used to analyse how each mentioned Factor influences the assessment, and why and when they should be included in the model....

  20. Windfarm Generation Assessment for ReliabilityAnalysis of Power Systems

    DEFF Research Database (Denmark)

    Negra, Nicola Barberis; Holmstrøm, Ole; Bak-Jensen, Birgitte

    2007-01-01

    Due to the fast development of wind generation in the past ten years, increasing interest has been paid to techniques for assessing different aspects of power systems with a large amount of installed wind generation. One of these aspects concerns power system reliability. Windfarm modelling plays...... in a reliability model and the generation of a windfarm is evaluated by means of sequential Monte Carlo simulation. Results are used to analyse how each mentioned Factor influences the assessment, and why and when they should be included in the model....

  1. Electric vehicle with downhill electro-generating system

    Energy Technology Data Exchange (ETDEWEB)

    Stulbach, N.; Yuter, S.C.

    1993-06-01

    A vehicle adapted to be driven by an electrical motor electrically connected to charge storage battery means and having an electro-operating system is described comprising a first dynamo electric generator, first mechanical turns amplifier means for coupling said first dynamo electric generator to a road wheels axle of the vehicle, a second dynamo electric generator, downhill sensing means coupled to a portion of the vehicle, and second mechanical turns amplifier means responsive to said downhill sensing means for automatically coupling said second dynamo electric generator to a road wheels axle of the vehicle only when the vehicle is going downhill, whereby said first dynamo electric generator is driven by the amplified rotation of the axle whenever said axle rotates thereby converting movement of the vehicle into electrical energy, and said second dynamo electric generator is automatically driven by the amplified rotation of the axle only when said vehicle is going downhill thereby converting downhill movement of the vehicle into electrical energy.

  2. Optimal design of an atmospheric water generator (AWG) based on thermo-electric cooler (TEC) for drought in rural area

    Science.gov (United States)

    Suryaningsih, Sri; Nurhilal, Otong

    2016-02-01

    Drinking water availability is a major issue in some rural area in Indonesia during the summer season due to lack of rainfall, which peoples in this area have to fetch the water a few kilometers away from home. The Atmospheric Water Generator (AWG) is one of the alternative solution for fresh water recovery from atmosphere which is directly condensed the moisture content of water vapor from the air. This paper presents the method to develop a prototype of an AWG based on Thermo-electric cooler (TEC) that used 12 Volt DC, hence its suitability for using renewable energy resource. Computational Fluid Dynamics (CFD) is utilized to optimize the design process in the flow region only, it's not suitable for recent CFD software to use in Multi physics, because inaccuracy, cost and time saving. Some parameters such as temperature, moisture content, air flow, pressure, form of air flow channel and the water productivity per unit input of energy are to be considered. The result is presented as an experimental prototype of an AWG based on TEC and compared with other conventional commercial products.

  3. Model Oriented Application Generation for Industrial Control Systems

    CERN Document Server

    Copy, B; Blanco Vinuela, E; Fernandez Adiego, B; Nogueira Ferandes, R; Prieto Barreiro, I

    2011-01-01

    The CERN Unified Industrial Control Systems framework (UNICOS) is a software generation methodology and a collection of development tools that standardizes the design of industrial control applications [1]. A Software Factory, named the UNICOS Application Builder (UAB) [2], was introduced to ease extensibility and maintenance of the framework, introducing a stable metamodel, a set of platformindependent models and platformspecific configurations against which code generation plugins and configuration generation plugins can be written. Such plugins currently target PLC programming environments (Schneider and SIEMENS PLCs) as well as SIEMENS WinCC Open Architecture SCADA (previously known as ETM PVSS) but are being expanded to cover more and more aspects of process control systems. We present what constitutes the UNICOS metamodel and the models in use, how these models can be used to capture knowledge about industrial control systems and how this knowledge can be leveraged to generate both code and configuratio...

  4. An Ethernet LAN based distributed generation system load shedding strategy

    DEFF Research Database (Denmark)

    Wei, Mu; Chen, Zhe

    2011-01-01

    This paper firstly analyzes and compares various communication technologies, and proposes a communication system for a distributed generation system (DGS) with wind turbines. Then the paper presents a novel simulation method of considering the interactions between the communication system and power...... system, by using two software platforms: OPNET and EMTDC/PSCAD. A control method based on the communication technique has been designed to stabilize the DG system during power system disturbances. A case study is presented to demonstrate the effectiveness of the proposed communication system, simulation...... method and control strategy....

  5. Dynamic Braking System of a Tidal Generator: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Muljadi, Eduard; Wright, Alan; Gevorgian, Vahan; Donegan, James; Marnagh, Cian; McEntee, Jarlath

    2016-08-01

    Renewable energy generation has experienced significant cost reductions during the past decades, and it has become more accepted by the global population. In the beginning, wind generation dominated the development and deployment of renewable energy; however, during recent decades, photovoltaic (PV) generation has grown at a very significant pace due to the tremendous decrease in the cost of PV modules. The focus on renewable energy generation has now expanded to include new types with promising future applications, such as river and tidal generation. The input water flow to these types of resources is more predictable than wind or solar generation. The data used in this paper is representative of a typical river or tidal generator. The analysis is based on a generator with a power rating of 40 kW. The tidal generator under consideration is driven by two sets of helical turbines connected to each side of the generator located in between the turbines. The generator is operated in variable speed, and it is controlled to maximize the energy harvested as well as the operation of the turbine generator. The electrical system consists of a three-phase permanent magnet generator connected to a three-phase passive rectifier. The output of the rectifier is connected to a DC-DC converter to match the rectifier output to the DC bus voltage of the DC-AC inverter. The three-phase inverter is connected to the grid, and it is controlled to provide a good interface with the grid. One important aspect of river and tidal generation is the braking mechanism. In a tidal generator, the braking mechanism is important to avoid a runaway condition in case the connection to the grid is lost when there is a fault in the lines. A runaway condition may lead to an overspeed condition and cause extreme stresses on the turbine blade structure and eventual disintegration of the mechanical structure. In this paper, the concept of the dynamic braking system is developed and investigated for normal

  6. Experimental Investigation and Modeling of Integrated Tri-generation Systems

    Science.gov (United States)

    Cetinkaya, Eda

    Energy demand in the world is increasing with population growth and higher living standards. Today, the need for energy requires a focus on renewable sources without abandoning fossil fuels. Efficient use of energy is one of the most important tasks in modern energy systems to achieve. In addition to the energy need, growing environmental concerns are linked with energy is emerged. Multi-purpose energy generation allows a higher efficiency by generating more outputs with the same input in the same system. Tri-generation systems are expected to provide at least three commodities, such as heating, cooling, desalination, storable fuel production and some other useful outputs, in addition to power generation. In this study, an experimental investigation of gasification is presented and two integrated tri-generation systems are proposed. The first integrated tri-generation system (System 1) utilizes solar energy as input and the outputs are power, fresh water and hot water. It consists of four sub-systems, namely solar power tower system, desalination system, Rankine cycle and organic Rankine cycle (ORC). The second integrated tri-generation system (System 2) utilizes coal and biomass as input and the outputs are power, fuel and hot water. It consists of five sub-systems: gasification plant, Brayton cycle, Rankine cycle, Fischer-Tropsch synthesis plant and an organic Rankine cycle (ORC). Experimental investigation includes coal and biomass gasification, where the experimental results of synthesis gas compositions are utilized in the analysis of the second systems. To maximize efficiency, heat losses from the system should be minimized through a recovery system to make the heat a useful commodity for other systems, such as ORCs which can utilize the low-grade heat. In this respect, ORCs are first analyzed for three different configurations in terms of energy and exergy efficiencies altering working fluids to increase the power output. Among two types of coal and one type

  7. Design and optimization of flexible multi-generation systems

    DEFF Research Database (Denmark)

    Lythcke-Jørgensen, Christoffer Ernst

    term energy system development; biomass supply chains and local resource availability; combined with global sensitivity and uncertainty analysis. The methodology includes a novel method for aggregating external operating condition datasets, named the CHOP method. In addition, three case studies...... of variable renewable energy sources in a cost-effective way by linking the different sectors in the energy system with local energy supply systems. A key challenge faced in the development of flexible multi-generation system is the knowledge gap between process design practices, which simplify energy system...... of flexible multi-generation system. In addition, the case study results emphasize the importance of considering flexible operation, systematic process integration, and systematic assessment of uncertainties in the design optimization. It is recommended that future research focus on assessing system impacts...

  8. Development of a cooling system for superconducting wind turbine generator

    Science.gov (United States)

    Furuse, Mitsuho; Fuchino, Shuichiro; Okano, Makoto; Natori, Naotake; Yamasaki, Hirofumi

    2016-12-01

    This paper deals with the cooling system for high-Tc superconducting (HTS) generators for large capacity wind turbines. We have proposed a cooling system with a heat exchanger and circulation pumps to cool HTS field windings designed for 10 MW-class superconducting generators. In the cooling system, the refrigerants in the stationary and rotational systems are completely separated; heat between the two systems exchanges using a rotational-stationary heat exchanger. The refrigerant in rotational system is circulated by highly reliable pumps. We designed the rotational-stationary heat exchanger based on a conventional shell-and tube type heat exchanger. We also demonstrated that heat exchange in cryogenic temperature is possible with a commercially available heat exchanger. We devised a novel and highly reliable cryogenic helium circulation pump with magnetic reciprocating rotation system and verified its underlying principle with a small-scale model.

  9. Numerical simulation of the generation of reactive oxygen and nitrogen species (RONS) in water by atmospheric-pressure plasmas and their effects on Escherichia coli (E. coli)

    Science.gov (United States)

    Ikuse, Kazumasa; Hamaguchi, Satoshi

    2016-09-01

    We have used two types of numerical simulations to examine biological effects of reactive oxygen and nitrogen species (RONS) generated in water by an atmospheric-pressure plasma (APP) that irradiates the water surface. One is numerical simulation for the generation and transport of RONS in water based on the reaction-diffusion-advection equations coupled with Poisson equation. The rate constants, mobilities, and diffusion coefficients used in the equations are obtained from the literature. The gaseous species are given as boundary conditions and time evolution of the concentrations of chemical species in pure water is solved numerically as functions of the depth in one dimension. Although it is not clear how living organisms respond to such exogenous RONS, we also use numerical simulation for metabolic reactions of Escherichia coli (E. coli) and examine possible effects of such RONS on an in-silico model organism. The computation model is based on the flux balance analysis (FBA), where the fluxes of the metabolites in a biological system are evaluated in steady state, i.e., under the assumption that the fluxes do not change in time. The fluxes are determined with liner programming to maximize the growth rate of the bacteria under the given conditions. Although FBA cannot be directly applied to dynamical responses of metabolic reactions, the simulation still gives insight into the biological reactions to exogenous chemical species generated by an APP. Partially supported by JSPS Grants-in-Aid for Scientific Research.

  10. Protection issues on microgrid/distributed generation based systems

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Angelo R. [Centro Federal de Educacao Tecnologica de Minas Gerais (CEFET-MG), Belo Horizonte, MG (Brazil); Ribeiro, Paulo F. [Calvin College, Grand Rapids, MI (United States). Dept. of Electrical Engineering; Iung, Anderson M. [Geracao Paranapanema S.A., SP (Brazil). Duke Energy International. Market Analysis Dept.; Garcia, Paulo A.N. [Federal University of Juiz de Fora (UFJF), MG (Brazil). Dept. of Circuits

    2009-07-01

    This paper aims to discuss protection issues related to the presence of distributed generation (DG) in distribution systems. A case study is developed to show some impacts of transitions and operations with relay static settings to verify the reliability of systems in the presence of DG. (author)

  11. Material challenges for the next generation of fission reactor systems

    Energy Technology Data Exchange (ETDEWEB)

    Buckthorpe, Derek [AMEC, Knutsford, Cheshire (United Kingdom)

    2010-07-01

    The new generation of fission reactor systems wil require the deployment and construction of a series of advanced water cooled reactors as part of a package of measures to meet UK and European energy needs and to provide a near term non-fossil fuel power solution that addresses CO{sub 2} emission limits. In addition new longer term Generation IV reactor tye systems are being developed and evaluated to enhance safety, reliability, sustainability economics and proliferation resistance requirements and to meet alternative energy applications (outside of electricity generation) such as process heat and large scale hydrogen generation. New fission systems will impose significant challenges on materials supply and development. In the near term, because of the need to 'gear up' to large scale construction after decades of industrial hibernation/contraction and, in the longer term, because of the need for materials to operate under more challenging environments requiring the deployment and development of new alternative materials not yet established to an industrial stage. This paper investigates the materials challenges imposed by the new Generation III+ and Generation IV systems. These include supply and fabrication issues, development of new high temperature alloys and non-metallic materials, the use of new methods of manufacture and the best use of currently available resources and minerals. Recommendations are made as to how these materials challenges might be met and how governments, industry, manufacturers and researchers can all play their part. (orig.)

  12. Mathematical modeling of control system for the experimental steam generator

    Directory of Open Access Journals (Sweden)

    Podlasek Szymon

    2016-01-01

    Full Text Available A steam generator is an essential unit of each cogeneration system using steam machines. Currently one of the cheapest ways of the steam generation can be application of old steam generators came from army surplus store. They have relatively simple construction and in case of not so exploited units – quite good general conditions, and functionality of mechanical components. By contrast, electrical components and control systems (mostly based on relay automatics are definitely obsolete. It is not possible to use such units with cooperation of steam bus or with steam engines. In particular, there is no possibility for automatically adjustment of the pressure and the temperature of the generated steam supplying steam engines. Such adjustment is necessary in case of variation of a generator load. The paper is devoted to description of improvement of an exemplary unit together with construction of the measurement-control system based on a PLC. The aim was to enable for communication between the steam generator and controllers of the steam bus and steam engines in order to construction of a complete, fully autonomic and maintenance-free microcogeneration system.

  13. Mathematical modeling of control system for the experimental steam generator

    Science.gov (United States)

    Podlasek, Szymon; Lalik, Krzysztof; Filipowicz, Mariusz; Sornek, Krzysztof; Kupski, Robert; Raś, Anita

    2016-03-01

    A steam generator is an essential unit of each cogeneration system using steam machines. Currently one of the cheapest ways of the steam generation can be application of old steam generators came from army surplus store. They have relatively simple construction and in case of not so exploited units - quite good general conditions, and functionality of mechanical components. By contrast, electrical components and control systems (mostly based on relay automatics) are definitely obsolete. It is not possible to use such units with cooperation of steam bus or with steam engines. In particular, there is no possibility for automatically adjustment of the pressure and the temperature of the generated steam supplying steam engines. Such adjustment is necessary in case of variation of a generator load. The paper is devoted to description of improvement of an exemplary unit together with construction of the measurement-control system based on a PLC. The aim was to enable for communication between the steam generator and controllers of the steam bus and steam engines in order to construction of a complete, fully autonomic and maintenance-free microcogeneration system.

  14. Optical pulse generation system for the National Ignition Facility (NIF)

    Energy Technology Data Exchange (ETDEWEB)

    Penko, F; Braucht,; Browning, D; Crane, J K; Dane, B; Deadrick, F; Dreifuerst, G; Henesian, M; Jones, B A; Kot, L; Laumann, C; Martinez, M; Moran, B; Rothenberg, J E; Skulina, K; Wilcox, R B

    1998-06-18

    We describe the Optical Pulse Generation (OPG) system for the National Ignition Facility ( NIF ). The OPG system begins with the Master Oscillator Room ( MOR ) where the initial, seed pulse for the entire laser system is produced and properly formatted to enhance ignition in the target. The formatting consists of temporally shaping the pulse and adding additional bandwidth to increase the coupling of the laser generated x-rays to the high density target plasma. The pulse produced in the MOR fans out to 48 identical preamplifier modules where it is amplified by a factor of ten billion and spatially shaped for injection into the 192 main amplifier chai

  15. Control and operation of distributed generation in distribution systems

    DEFF Research Database (Denmark)

    Mahat, Pukar; Chen, Zhe; Bak-Jensen, Birgitte

    2011-01-01

    Many distribution systems nowadays have significant penetration of distributed generation (DG)and thus, islanding operation of these distribution systems is becoming a viable option for economical and technical reasons. The DG should operate optimally during both grid-connected and island...... algorithm, which uses average rate of change off requency (Af5) and real power shift RPS), in the islanded mode. RPS will increase or decrease the power set point of the generator with increasing or decreasing system frequency, respectively. Simulation results show that the proposed method can operate...

  16. Extreme events in excitable systems and mechanisms of their generation.

    Science.gov (United States)

    Ansmann, Gerrit; Karnatak, Rajat; Lehnertz, Klaus; Feudel, Ulrike

    2013-11-01

    We study deterministic systems, composed of excitable units of FitzHugh-Nagumo type, that are capable of self-generating and self-terminating strong deviations from their regular dynamics without the influence of noise or parameter change. These deviations are rare, short-lasting, and recurrent and can therefore be regarded as extreme events. Employing a range of methods we analyze dynamical properties of the systems, identifying features in the systems' dynamics that may qualify as precursors to extreme events. We investigate these features and elucidate mechanisms that may be responsible for the generation of the extreme events.

  17. Formal Specification Based Automatic Test Generation for Embedded Network Systems

    Directory of Open Access Journals (Sweden)

    Eun Hye Choi

    2014-01-01

    Full Text Available Embedded systems have become increasingly connected and communicate with each other, forming large-scaled and complicated network systems. To make their design and testing more reliable and robust, this paper proposes a formal specification language called SENS and a SENS-based automatic test generation tool called TGSENS. Our approach is summarized as follows: (1 A user describes requirements of target embedded network systems by logical property-based constraints using SENS. (2 Given SENS specifications, test cases are automatically generated using a SAT-based solver. Filtering mechanisms to select efficient test cases are also available in our tool. (3 In addition, given a testing goal by the user, test sequences are automatically extracted from exhaustive test cases. We’ve implemented our approach and conducted several experiments on practical case studies. Through the experiments, we confirmed the efficiency of our approach in design and test generation of real embedded air-conditioning network systems.

  18. Distributed Generation in Power Systems: An Overview and Key Issues

    DEFF Research Database (Denmark)

    Singh, Sri Niwas

    2009-01-01

    The necessity for smart electrical systems having minimum technical loss and environmental impact is providing impetus to go for Distributed Generations (DGs) which may offer several other advantages such as reduced transmission and distribution system resources, increased reliability, better power...... quality, etc. However, depending on the system configuration and management, these advantages may not be true. Moreover, due to structural and managerial changes in the electricity supply industry motivated with introduction of completion, the role of small generations distributed in the low....../medium voltage network has gained importance. This paper adopts a systematic approach by focusing on the most important research areas related to the distributed generations. Various DG technologies are described and penetration of DGs in the Indian system has been discussed. This paper also highlights the key...

  19. Overview of Solar Wind-Magnetosphere-Ionosphere-Atmosphere Coupling and the Generation of Magnetospheric Currents

    Science.gov (United States)

    Milan, S. E.; Clausen, L. B. N.; Coxon, J. C.; Carter, J. A.; Walach, M.-T.; Laundal, K.; Østgaard, N.; Tenfjord, P.; Reistad, J.; Snekvik, K.; Korth, H.; Anderson, B. J.

    2017-02-01

    We review the morphology and dynamics of the electrical current systems of the terrestrial magnetosphere and ionosphere. Observations from the Active Magnetosphere and Planetary Electrodynamics Response Experiment (AMPERE) over the three years 2010 to 2012 are employed to illustrate the variability of the field-aligned currents that couple the magnetosphere and ionosphere, on timescales from minutes to years, in response to the impact of solar wind disturbances on the magnetosphere and changes in the level of solar illumination of the polar ionospheres. The variability is discussed within the context of the occurrence of magnetic reconnection between the solar wind and terrestrial magnetic fields at the magnetopause, the transport of magnetic flux within the magnetosphere, and the onset of magnetic reconnection in the magnetotail. The conditions under which the currents are expected to be weak, and hence minimally contaminate measurements of the internally-produced magnetic field of the Earth, are briefly outlined.

  20. Next generation Zero-Code control system UI

    CERN Document Server

    CERN. Geneva

    2017-01-01

    Developing ergonomic user interfaces for control systems is challenging, especially during machine upgrade and commissioning where several small changes may suddenly be required. Zero-code systems, such as *Inspector*, provide agile features for creating and maintaining control system interfaces. More so, these next generation Zero-code systems bring simplicity and uniformity and brake the boundaries between Users and Developers. In this talk we present *Inspector*, a CERN made Zero-code application development system, and we introduce the major differences and advantages of using Zero-code control systems to develop operational UI.

  1. Natural Atmospheric Environment Model Development for the National Aeronautics and Space Administration's Second Generation Reusable Launch Vehicle

    Science.gov (United States)

    Roberts, Barry C.; Leahy, Frank; Overbey, Glenn; Batts, Glen W.; Parker, Nelson (Technical Monitor)

    2002-01-01

    The National Aeronautics and Space Administration (NASA) recently began development of a new reusable launch vehicle. The program office is located at Marshall Space Flight Center (MSFC) and is called the Second Generation Reusable Launch Vehicle (2GRLV). The purpose of the program is to improve upon the safety and reliability of the first generation reusable launch vehicle, the Space Shuttle. Specifically, the goals are to reduce the risk of crew loss to less than 1-in-10,000 missions and decreased costs by a factor of 10 to approximately $1,000 per pound of payload launched to low Earth orbit. The program is currently in the very early stages of development and many two-stage vehicle concepts will be evaluated. Risk reduction activities are also taking place. These activities include developing new technologies and advancing current technologies to be used by the vehicle. The Environments Group at MSFC is tasked by the 2GRLV Program to develop and maintain an extensive series of analytical tools and environmental databases which enable it to provide detailed atmospheric studies in support of structural, guidance, navigation and control, and operation of the 2GRLV.

  2. A mobile polar atmospheric parameter measurement system:II. First atmospheric turbulence observation at Antarctic Taishan Station

    Institute of Scientific and Technical Information of China (English)

    TIAN Qiguo; JIANG Peng; WU Xiaoqing; JIN Xinmiao; LU Shan; JI Tuo; CHAI Bo; ZHANG Shaohua; ZHOU Hongyan

    2015-01-01

    This is the second paper of a series devoted to atmospheric optical turbulence Cn2 observation using a mobile polar atmospheric parameter measurement system. We present the initial results of Cn2 measurement at Antarctic Taishan Station using micro-thermal sensors and a three-dimensional sonic anemometer at height ~2.0 m above the snow surface. The site testing experiments were carried out during the 30th Chinese National Antarctic Research Expedition (CHINARE). We collected about 1 000 h of data between 30 December 2013 and 10 February 2014. The Cn2 curve exhibits clear daily structures, with two peaks around midnight and midday and two troughs around 7:30 and 17:00 local time (UTC+5). The mean Cn2 is 2.7×10−15 m−2/3 and the 25th and 75th percentiles of the Cn2 cumulative distribution are 9.6×10−16 m−2/3 and 6.2×10−15 m−2/3, respectively. Meteorological parameters such as temperature, relative humidity, wind speed, and air pressure are also presented.

  3. Generating function approach to reliability analysis of structural systems

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The generating function approach is an important tool for performance assessment in multi-state systems. Aiming at strength reliability analysis of structural systems, generating function approach is introduced and developed. Static reliability models of statically determinate, indeterminate systems and fatigue reliability models are built by constructing special generating functions, which are used to describe probability distributions of strength (resistance), stress (load) and fatigue life, by defining composite operators of generating functions and performance structure functions thereof. When composition operators are executed, computational costs can be reduced by a big margin by means of collecting like terms. The results of theoretical analysis and numerical simulation show that the generating function approach can be widely used for probability modeling of large complex systems with hierarchical structures due to the unified form, compact expression, computer program realizability and high universality. Because the new method considers twin loads giving rise to component failure dependency, it can provide a theoretical reference and act as a powerful tool for static, dynamic reliability analysis in civil engineering structures and mechanical equipment systems with multi-mode damage coupling.

  4. Description of Atmospheric Conditions at the Pierre Auger Observatory using the Global Data Assimilation System (GDAS)

    CERN Document Server

    Abreu, P; Ahlers, M; Ahn, E J; Albuquerque, I F M; Allard, D; Allekotte, I; Allen, J; Allison, P; Almela, A; Castillo, J Alvarez; Alvarez-Muñiz, J; Ambrosio, M; Aminaei, A; Anchordoqui, L; Andringa, S; Antičić, T; Aramo, C; Arganda, E; Arqueros, F; Asorey, H; Assis, P; Aublin, J; Ave, M; Avenier, M; Avila, G; Bäcker, T; Badescu, A M; Balzer, M; Barber, K B; Barbosa, A F; Bardenet, R; Barroso, S L C; Baughman, B; Bäuml, J; Beatty, J J; Becker, B R; Becker, K H; Bellétoile, A; Bellido, J A; BenZvi, S; Berat, C; Bertou, X; Biermann, P L; Billoir, P; Blanco, F; Blanco, M; Bleve, C; Blümer, H; Boháčová, M; Boncioli, D; Bonifazi, C; Bonino, R; Borodai, N; Brack, J; Brancus, I; Brogueira, P; Brown, W C; Bruijn, R; Buchholz, P; Bueno, A; Burton, R E; Caballero-Mora, K S; Caccianiga, B; Caramete, L; Caruso, R; Castellina, A; Catalano, O; Cataldi, G; Cazon, L; Cester, R; Chauvin, J; Cheng, S H; Chiavassa, A; Chinellato, J A; Diaz, J Chirinos; Chudoba, J; Clay, R W; Coluccia, M R; Conceição, R; Contreras, F; Cook, H; Cooper, M J; Coppens, J; Cordier, A; Coutu, S; Covault, C E; Creusot, A; Criss, A; Cronin, J; Curutiu, A; Dagoret-Campagne, S; Dallier, R; Daniel, B; Dasso, S; Daumiller, K; Dawson, B R; de Almeida, R M; De Domenico, M; De Donato, C; de Jong, S J; De La Vega, G; Junior, W J M de Mello; Neto, J R T de Mello; De Mitri, I; de Souza, V; de Vries, K D; del Peral, L; del Río, M; Deligny, O; Dembinski, H; Dhital, N; Di Giulio, C; Castro, M L Díaz; Diep, P N; Diogo, F; Dobrigkeit, C; Docters, W; D'Olivo, J C; Dong, P N; Dorofeev, A; Anjos, J C dos; Dova, M T; D'Urso, D; Dutan, I; Ebr, J; Engel, R; Erdmann, M; Escobar, C O; Espadanal, J; Etchegoyen, A; Luis, P Facal San; Tapia, I Fajardo; Falcke, H; Farrar, G; Fauth, A C; Fazzini, N; Ferguson, A P; Fick, B; Filevich, A; Filipčič, A; Fliescher, S; Fracchiolla, C E; Fraenkel, E D; Fratu, O; Fröhlich, U; Fuchs, B; Gaior, R; Gamarra, R F; Gambetta, S; García, B; Roca, S T Garcia; Garcia-Gamez, D; Garcia-Pinto, D; Gascon, A; Gemmeke, H; Ghia, P L; Giaccari, U; Giller, M; Glass, H; Gold, M S; Golup, G; Albarracin, F Gomez; Berisso, M Gómez; Vitale, P F Gómez; Gonçalves, P; Gonzalez, D; Gonzalez, J G; Gookin, B; Gorgi, A; Gouffon, P; Grashorn, E; Grebe, S; Griffith, N; Grigat, M; Grillo, A F; Guardincerri, Y; Guarino, F; Guedes, G P; Guzman, A; Hansen, P; Harari, D; Harrison, T A; Harton, J L; Haungs, A; Hebbeker, T; Heck, D; Herve, A E; Hojvat, C; Hollon, N; Holmes, V C; Homola, P; Hörandel, J R; Horneffer, A; Horvath, P; Hrabovský, M; Huber, D; Huege, T; Insolia, A; Ionita, F; Italiano, A; Jarne, C; Jiraskova, S; Josebachuili, M; Kadija, K; Kampert, K H; Karhan, P; Kasper, P; Kégl, B; Keilhauer, B; Keivani, A; Kelley, J L; Kemp, E; Kieckhafer, R M; Klages, H O; Kleifges, M; Kleinfeller, J; Knapp, J; Koang, D -H; Kotera, K; Krohm, N; Krömer, O; Kruppke-Hansen, D; Kuehn, F; Kuempel, D; Kulbartz, J K; Kunka, N; La Rosa, G; Lachaud, C; LaHurd, D; Latronico, L; Lauer, R; Lautridou, P; Coz, S Le; Leão, M S A B; Lebrun, D; Lebrun, P; de Oliveira, M A Leigui; Letessier-Selvon, A; Lhenry-Yvon, I; Link, K; López, R; Agüera, A Lopez; Louedec, K; Bahilo, J Lozano; Lu, L; Lucero, A; Ludwig, M; Lyberis, H; Maccarone, M C; Macolino, C; Maldera, S; Mandat, D; Mantsch, P; Mariazzi, A G; Marin, J; Marin, V; Maris, I C; Falcon, H R Marquez; Marsella, G; Martello, D; Martin, L; Martinez, H; Bravo, O Martínez; Mathes, H J; Matthews, J; Matthews, J A J; Matthiae, G; Maurel, D; Maurizio, D; Mazur, P O; Medina-Tanco, G; Melissas, M; Melo, D; Menichetti, E; Menshikov, A; Mertsch, P; Meurer, C; Mićanović, S; Micheletti, M I; Minaya, I A; Miramonti, L; Molina-Bueno, L; Mollerach, S; Monasor, M; Ragaigne, D Monnier; Montanet, F; Morales, B; Morello, C; Moreno, E; Moreno, J C; Mostafá, M; Moura, C A; Muller, M A; Müller, G; Münchmeyer, M; Mussa, R; Navarra, G; Navarro, J L; Navas, S; Necesal, P; Nellen, L; Nelles, A; Neuser, J; Nhung, P T; Niechciol, M; Niemietz, L; Nierstenhoefer, N; Nitz, D; Nosek, D; Nožka, L; Oehlschläger, J; Olinto, A; Ortiz, M; Pacheco, N; Selmi-Dei, D Pakk; Palatka, M; Pallotta, J; Palmieri, N; Parente, G; Parizot, E; Parra, A; Pastor, S; Paul, T; Pech, M; Pȩkala, J; Pelayo, R; Pepe, I M; Perrone, L; Pesce, R; Petermann, E; Petrera, S; Petrinca, P; Petrolini, A; Petrov, Y; Pfendner, C; Piegaia, R; Pierog, T; Pieroni, P; Pimenta, M; Pirronello, V; Platino, M; Ponce, V H; Pontz, M; Porcelli, A; Privitera, P; Prouza, M; Quel, E J; Querchfeld, S; Rautenberg, J; Ravel, O; Ravignani, D; Revenu, B; Ridky, J; Riggi, S; Risse, M; Ristori, P; Rivera, H; Rizi, V; Roberts, J; de Carvalho, W Rodrigues; Rodriguez, G; Martino, J Rodriguez; Rojo, J Rodriguez; Rodriguez-Cabo, I; Rodríguez-Frías, M D; Ros, G; Rosado, J; Rossler, T; Roth, M; Rouillé-d'Orfeuil, B; Roulet, E; Rovero, A C; Rühle, C; Saftoiu, A; Salamida, F; Salazar, H; Greus, F Salesa; Salina, G; Sánchez, F; Santo, C E; Santos, E; Santos, E M; Sarazin, F; Sarkar, B; Sarkar, S; Sato, R; Scharf, N; Scherini, V; Schieler, H; Schiffer, P; Schmidt, A; Scholten, O; Schoorlemmer, H; Schovancova, J; Schovánek, P; Schröder, F; Schulte, S; Schuster, D; Sciutto, S J; Scuderi, M; Segreto, A; Settimo, M; Shadkam, A; Shellard, R C; Sidelnik, I; Sigl, G; Lopez, H H Silva; Sima, O; Śmiałkowski, A; Šmída, R; Snow, G R; Sommers, P; Sorokin, J; Spinka, H; Squartini, R; Srivastava, Y N; Stanic, S; Stapleton, J; Stasielak, J; Stephan, M; Stutz, A; Suarez, F; Suomijärvi, T; Supanitsky, A D; Šuša, T; Sutherland, M S; Swain, J; Szadkowski, Z; Szuba, M; Tapia, A; Tartare, M; Taşcău, O; Ruiz, C G Tavera; Tcaciuc, R; Thao, N T; Thomas, D; Tiffenberg, J; Timmermans, C; Tkaczyk, W; Peixoto, C J Todero; Toma, G; Tomankova, L; Tomé, B; Tonachini, A; Travnicek, P; Tridapalli, D B; Tristram, G; Trovato, E; Tueros, M; Ulrich, R; Unger, M; Urban, M; Galicia, J F Valdés; Valiño, I; Valore, L; Berg, A M van den; Varela, E; Cárdenas, B Vargas; Vázquez, J R; Vázquez, R A; Veberič, D; Verzi, V; Vicha, J; Videla, M; Villaseñor, L; Wahlberg, H; Wahrlich, P; Wainberg, O; Walz, D; Watson, A A; Weber, M; Weidenhaupt, K; Weindl, A; Werner, F; Westerhoff, S; Whelan, B J; Widom, A; Wieczorek, G; Wiencke, L; Wilczyńska, B; Wilczyński, H; Will, M; Williams, C; Winchen, T; Wommer, M; Wundheiler, B; Yamamoto, T; Yapici, T; Younk, P; Yuan, G; Yushkov, A; Zamorano, B; Zas, E; Zavrtanik, D; Zavrtanik, M; Zaw, I; Zepeda, A; Zhu, Y; Silva, M Zimbres; Ziolkowski, M; 10.1016/j.astropartphys.2011.12.002

    2012-01-01

    Atmospheric conditions at the site of a cosmic ray observatory must be known for reconstructing observed extensive air showers. The Global Data Assimilation System (GDAS) is a global atmospheric model predicated on meteorological measurements and numerical weather predictions. GDAS provides altitude-dependent profiles of the main state variables of the atmosphere like temperature, pressure, and humidity. The original data and their application to the air shower reconstruction of the Pierre Auger Observatory are described. By comparisons with radiosonde and weather station measurements obtained on-site in Malarg\\"ue and averaged monthly models, the utility of the GDAS data is shown.

  5. Description of atmospheric conditions at the Pierre Auger Observatory using the Global Data Assimilation System (GDAS)

    Science.gov (United States)

    Pierre Auger Collaboration; Abreu, P.; Aglietta, M.; Ahlers, M.; Ahn, E. J.; Albuquerque, I. F. M.; Allard, D.; Allekotte, I.; Allen, J.; Allison, P.; Almela, A.; Alvarez Castillo, J.; Alvarez-Muñiz, J.; Ambrosio, M.; Aminaei, A.; Anchordoqui, L.; Andringa, S.; Antiči'C, T.; Aramo, C.; Arganda, E.; Arqueros, F.; Asorey, H.; Assis, P.; Aublin, J.; Ave, M.; Avenier, M.; Avila, G.; Bäcker, T.; Badescu, A. M.; Balzer, M.; Barber, K. B.; Barbosa, A. F.; Bardenet, R.; Barroso, S. L. C.; Baughman, B.; Bäuml, J.; Beatty, J. J.; Becker, B. R.; Becker, K. H.; Bellétoile, A.; Bellido, J. A.; Benzvi, S.; Berat, C.; Bertou, X.; Biermann, P. L.; Billoir, P.; Blanco, F.; Blanco, M.; Bleve, C.; Blümer, H.; Boháčová, M.; Boncioli, D.; Bonifazi, C.; Bonino, R.; Borodai, N.; Brack, J.; Brancus, I.; Brogueira, P.; Brown, W. C.; Bruijn, R.; Buchholz, P.; Bueno, A.; Burton, R. E.; Caballero-Mora, K. S.; Caccianiga, B.; Caramete, L.; Caruso, R.; Castellina, A.; Catalano, O.; Cataldi, G.; Cazon, L.; Cester, R.; Chauvin, J.; Cheng, S. H.; Chiavassa, A.; Chinellato, J. A.; Chirinos Diaz, J.; Chudoba, J.; Clay, R. W.; Coluccia, M. R.; Conceição, R.; Contreras, F.; Cook, H.; Cooper, M. J.; Coppens, J.; Cordier, A.; Coutu, S.; Covault, C. E.; Creusot, A.; Criss, A.; Cronin, J.; Curutiu, A.; Dagoret-Campagne, S.; Dallier, R.; Daniel, B.; Dasso, S.; Daumiller, K.; Dawson, B. R.; de Almeida, R. M.; de Domenico, M.; de Donato, C.; de Jong, S. J.; de La Vega, G.; de Mello Junior, W. J. M.; de Mello Neto, J. R. T.; de Mitri, I.; de Souza, V.; de Vries, K. D.; Del Peral, L.; Del Río, M.; Deligny, O.; Dembinski, H.; Dhital, N.; di Giulio, C.; Díaz Castro, M. L.; Diep, P. N.; Diogo, F.; Dobrigkeit, C.; Docters, W.; D'Olivo, J. C.; Dong, P. N.; Dorofeev, A.; Dos Anjos, J. C.; Dova, M. T.; D'Urso, D.; Dutan, I.; Ebr, J.; Engel, R.; Erdmann, M.; Escobar, C. O.; Espadanal, J.; Etchegoyen, A.; Facal San Luis, P.; Fajardo Tapia, I.; Falcke, H.; Farrar, G.; Fauth, A. C.; Fazzini, N.; Ferguson, A. P.; Fick, B.; Filevich, A.; Filipčič, A.; Fliescher, S.; Fracchiolla, C. E.; Fraenkel, E. D.; Fratu, O.; Fröhlich, U.; Fuchs, B.; Gaior, R.; Gamarra, R. F.; Gambetta, S.; García, B.; Garcia Roca, S. T.; Garcia-Gamez, D.; Garcia-Pinto, D.; Gascon, A.; Gemmeke, H.; Ghia, P. L.; Giaccari, U.; Giller, M.; Glass, H.; Gold, M. S.; Golup, G.; Gomez Albarracin, F.; Gómez Berisso, M.; Gómez Vitale, P. F.; Gonçalves, P.; Gonzalez, D.; Gonzalez, J. G.; Gookin, B.; Gorgi, A.; Gouffon, P.; Grashorn, E.; Grebe, S.; Griffith, N.; Grigat, M.; Grillo, A. F.; Guardincerri, Y.; Guarino, F.; Guedes, G. P.; Guzman, A.; Hansen, P.; Harari, D.; Harrison, T. A.; Harton, J. L.; Haungs, A.; Hebbeker, T.; Heck, D.; Herve, A. E.; Hojvat, C.; Hollon, N.; Holmes, V. C.; Homola, P.; Hörandel, J. R.; Horneffer, A.; Horvath, P.; Hrabovský, M.; Huber, D.; Huege, T.; Insolia, A.; Ionita, F.; Italiano, A.; Jarne, C.; Jiraskova, S.; Josebachuili, M.; Kadija, K.; Kampert, K. H.; Karhan, P.; Kasper, P.; Kégl, B.; Keilhauer, B.; Keivani, A.; Kelley, J. L.; Kemp, E.; Kieckhafer, R. M.; Klages, H. O.; Kleifges, M.; Kleinfeller, J.; Knapp, J.; Koang, D.-H.; Kotera, K.; Krohm, N.; Krömer, O.; Kruppke-Hansen, D.; Kuehn, F.; Kuempel, D.; Kulbartz, J. K.; Kunka, N.; La Rosa, G.; Lachaud, C.; Lahurd, D.; Latronico, L.; Lauer, R.; Lautridou, P.; Le Coz, S.; Leão, M. S. A. B.; Lebrun, D.; Lebrun, P.; Leigui de Oliveira, M. A.; Letessier-Selvon, A.; Lhenry-Yvon, I.; Link, K.; López, R.; Lopez Agüera, A.; Louedec, K.; Lozano Bahilo, J.; Lu, L.; Lucero, A.; Ludwig, M.; Lyberis, H.; Maccarone, M. C.; Macolino, C.; Maldera, S.; Mandat, D.; Mantsch, P.; Mariazzi, A. G.; Marin, J.; Marin, V.; Maris, I. C.; Marquez Falcon, H. R.; Marsella, G.; Martello, D.; Martin, L.; Martinez, H.; Martínez Bravo, O.; Mathes, H. J.; Matthews, J.; Matthews, J. A. J.; Matthiae, G.; Maurel, D.; Maurizio, D.; Mazur, P. O.; Medina-Tanco, G.; Melissas, M.; Melo, D.; Menichetti, E.; Menshikov, A.; Mertsch, P.; Meurer, C.; Mi'Canovi'C, S.; Micheletti, M. I.; Minaya, I. A.; Miramonti, L.; Molina-Bueno, L.; Mollerach, S.; Monasor, M.; Monnier Ragaigne, D.; Montanet, F.; Morales, B.; Morello, C.; Moreno, E.; Moreno, J. C.; Mostafá, M.; Moura, C. A.; Muller, M. A.; Müller, G.; Münchmeyer, M.; Mussa, R.; Navarra, G.; Navarro, J. L.; Navas, S.; Necesal, P.; Nellen, L.; Nelles, A.; Neuser, J.; Nhung, P. T.; Niechciol, M.; Niemietz, L.; Nierstenhoefer, N.; Nitz, D.; Nosek, D.; Nožka, L.; Oehlschläger, J.; Olinto, A.; Ortiz, M.; Pacheco, N.; Pakk Selmi-Dei, D.; Palatka, M.; Pallotta, J.; Palmieri, N.; Parente, G.; Parizot, E.; Parra, A.; Pastor, S.; Paul, T.; Pech, M.; Pȩkala, J.; Pelayo, R.; Pepe, I. M.; Perrone, L.; Pesce, R.; Petermann, E.; Petrera, S.; Petrinca, P.; Petrolini, A.; Petrov, Y.; Pfendner, C.; Piegaia, R.; Pierog, T.; Pieroni, P.; Pimenta, M.; Pirronello, V.; Platino, M.; Ponce, V. H.; Pontz, M.; Porcelli, A.; Privitera, P.; Prouza, M.; Quel, E. J.; Querchfeld, S.; Rautenberg, J.; Ravel, O.; Ravignani, D.; Revenu, B.; Ridky, J.; Riggi, S.; Risse, M.; Ristori, P.; Rivera, H.; Rizi, V.; Roberts, J.; Rodrigues de Carvalho, W.; Rodriguez, G.; Rodriguez Martino, J.; Rodriguez Rojo, J.; Rodriguez-Cabo, I.; Rodríguez-Frías, M. D.; Ros, G.; Rosado, J.; Rossler, T.; Roth, M.; Rouillé-D'Orfeuil, B.; Roulet, E.; Rovero, A. C.; Rühle, C.; Saftoiu, A.; Salamida, F.; Salazar, H.; Salesa Greus, F.; Salina, G.; Sánchez, F.; Santo, C. E.; Santos, E.; Santos, E. M.; Sarazin, F.; Sarkar, B.; Sarkar, S.; Sato, R.; Scharf, N.; Scherini, V.; Schieler, H.; Schiffer, P.; Schmidt, A.; Scholten, O.; Schoorlemmer, H.; Schovancova, J.; Schovánek, P.; Schröder, F.; Schulte, S.; Schuster, D.; Sciutto, S. J.; Scuderi, M.; Segreto, A.; Settimo, M.; Shadkam, A.; Shellard, R. C.; Sidelnik, I.; Sigl, G.; Silva Lopez, H. H.; Sima, O.; 'Smiałkowski, A.; Šmída, R.; Snow, G. R.; Sommers, P.; Sorokin, J.; Spinka, H.; Squartini, R.; Srivastava, Y. N.; Stanic, S.; Stapleton, J.; Stasielak, J.; Stephan, M.; Stutz, A.; Suarez, F.; Suomijärvi, T.; Supanitsky, A. D.; Šuša, T.; Sutherland, M. S.; Swain, J.; Szadkowski, Z.; Szuba, M.; Tapia, A.; Tartare, M.; Taşcău, O.; Tavera Ruiz, C. G.; Tcaciuc, R.; Thao, N. T.; Thomas, D.; Tiffenberg, J.; Timmermans, C.; Tkaczyk, W.; Todero Peixoto, C. J.; Toma, G.; Tomankova, L.; Tomé, B.; Tonachini, A.; Travnicek, P.; Tridapalli, D. B.; Tristram, G.; Trovato, E.; Tueros, M.; Ulrich, R.; Unger, M.; Urban, M.; Valdés Galicia, J. F.; Valiño, I.; Valore, L.; van den Berg, A. M.; Varela, E.; Vargascárdenas, B.; Vázquez, J. R.; Vázquez, R. A.; Veberič, D.; Verzi, V.; Vicha, J.; Videla, M.; Villaseñor, L.; Wahlberg, H.; Wahrlich, P.; Wainberg, O.; Walz, D.; Watson, A. A.; Weber, M.; Weidenhaupt, K.; Weindl, A.; Werner, F.; Westerhoff, S.; Whelan, B. J.; Widom, A.; Wieczorek, G.; Wiencke, L.; Wilczyńska, B.; Wilczyński, H.; Will, M.; Williams, C.; Winchen, T.; Wommer, M.; Wundheiler, B.; Yamamoto, T.; Yapici, T.; Younk, P.; Yuan, G.; Yushkov, A.; Zamorano, B.; Zas, E.; Zavrtanik, D.; Zavrtanik, M.; Zaw, I.; Zepeda, A.; Zhu, Y.; Zimbres Silva, M.; Ziolkowski, M.

    2012-04-01

    Atmospheric conditions at the site of a cosmic ray observatory must be known for reconstructing observed extensive air showers. The Global Data Assimilation System (GDAS) is a global atmospheric model predicated on meteorological measurements and numerical weather predictions. GDAS provides altitude-dependent profiles of the main state variables of the atmosphere like temperature, pressure, and humidity. The original data and their application to the air shower reconstruction of the Pierre Auger Observatory are described. By comparisons with radiosonde and weather station measurements obtained on-site in Malargüe and averaged monthly models, the utility of the GDAS data is shown.

  6. Description of Atmospheric Conditions at the Pierre Auger Observatory using the Global Data Assimilation System (GDAS)

    Energy Technology Data Exchange (ETDEWEB)

    Abreu, P.; /Lisbon, IST; Aglietta, M.; /Turin U. /INFN, Turin; Ahlers, M.; /Wisconsin U., Madison; Ahn, E.J.; /Fermilab; Albuquerque, I.F.M.; /Sao Paulo U.; Allard, D.; /APC, Paris; Allekotte, I.; /Buenos Aires, CONICET; Allen, J.; /New York U.; Allison, P.; /Ohio State U.; Almela, A.; /Natl. Tech. U., San Nicolas /Buenos Aires, CONICET; Alvarez Castillo, J.; /Mexico U., ICN /Santiago de Compostela U.

    2012-01-01

    Atmospheric conditions at the site of a cosmic ray observatory must be known for reconstructing observed extensive air showers. The Global Data Assimilation System (GDAS) is a global atmospheric model predicated on meteorological measurements and numerical weather predictions. GDAS provides altitude-dependent profiles of the main state variables of the atmosphere like temperature, pressure, and humidity. The original data and their application to the air shower reconstruction of the Pierre Auger Observatory are described. By comparisons with radiosonde and weather station measurements obtained on-site in Malargue and averaged monthly models, the utility of the GDAS data is shown.

  7. Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    David Deangelis; Rich Depuy; Debashis Dey; Georgia Karvountzi; Nguyen Minh; Max Peter; Faress Rahman; Pavel Sokolov; Deliang Yang

    2004-09-30

    This report summarizes the work performed by Hybrid Power Generation Systems, LLC (HPGS) during the April to October 2004 reporting period in Task 2.3 (SOFC Scaleup for Hybrid and Fuel Cell Systems) under Cooperative Agreement DE-FC26-01NT40779 for the U. S. Department of Energy, National Energy Technology Laboratory (DOE/NETL), entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. This study analyzes the performance and economics of power generation systems for central power generation application based on Solid Oxide Fuel Cell (SOFC) technology and fueled by natural gas. The main objective of this task is to develop credible scale up strategies for large solid oxide fuel cell-gas turbine systems. System concepts that integrate a SOFC with a gas turbine were developed and analyzed for plant sizes in excess of 20 MW. A 25 MW plant configuration was selected with projected system efficiency of over 65% and a factory cost of under $400/kW. The plant design is modular and can be scaled to both higher and lower plant power ratings. Technology gaps and required engineering development efforts were identified and evaluated.

  8. Geoinformation modeling system for analysis of atmosphere pollution impact on vegetable biosystems using space images

    Science.gov (United States)

    Polichtchouk, Yuri; Ryukhko, Viatcheslav; Tokareva, Olga; Alexeeva, Mary

    2002-02-01

    Geoinformation modeling system structure for assessment of the environmental impact of atmospheric pollution on forest- swamp ecosystems of West Siberia is considered. Complex approach to the assessment of man-caused impact based on the combination of sanitary-hygienic and landscape-geochemical approaches is reported. Methodical problems of analysis of atmosphere pollution impact on vegetable biosystems using geoinformation systems and remote sensing data are developed. Landscape structure of oil production territories in southern part of West Siberia are determined on base of processing of space images from spaceborn Resource-O. Particularities of atmosphere pollution zones modeling caused by gas burning in torches in territories of oil fields are considered. For instance, a pollution zones were revealed modeling of contaminants dispersal in atmosphere by standard model. Polluted landscapes areas are calculated depending on oil production volume. It is shown calculated data is well approximated by polynomial models.

  9. Evaluation of Routine Atmospheric Sounding Measurements Using Unmanned Systems (ERASMUS) Field Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    de Boer, Gijs [Univ. of Colorado, Boulder, CO (United States). Cooperative Inst. for Research in Environmental Sciences (CIRES); Lawrence, Dale [Univ. of Colorado, Boulder, CO (United States); Palo, Scott [Univ. of Colorado, Boulder, CO (United States); Argrow, Brian [Univ. of Colorado, Boulder, CO (United States); LoDolce, Gabriel [Univ. of Colorado, Boulder, CO (United States); Curry, Nathan [Univ. of Colorado, Boulder, CO (United States); Weibel, Douglas [Univ. of Colorado, Boulder, CO (United States); Finnamore, W [Univ. of Colorado, Boulder, CO (United States); D' Amore, P [Univ. of Colorado, Boulder, CO (United States); Borenstein, Steven [Univ. of Colorado, Boulder, CO (United States); Nichols, Tevis [Univ. of Colorado, Boulder, CO (United States); Elston, Jack [Blackswift Technologies, Boulder, CO (United States); Ivey, Mark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bendure, Al [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schmid, Beat [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Long, Chuck [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States). Earth System Research Lab.; Telg, Hagen [Univ. of Colorado, Boulder, CO (United States). Cooperative Inst. for Research in Environmental Sciences (CIRES); Gao, Rushan [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States). Earth System Research Lab.; Hock, T [National Center for Atmospheric Research, Boulder, CO (United States); Bland, Geoff [National Aeronautics and Space Administration (NASA), Washington, DC (United States)

    2017-03-01

    The Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems (ERASMUS) campaign was proposed with two central goals; to obtain scientifically relevant measurements of quantities related to clouds, aerosols, and radiation, including profiles of temperature, humidity, and aerosol particles, the structure of the arctic atmosphere during transitions between clear and cloudy states, measurements that would allow us to evaluate the performance of retrievals from U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility remote sensors in the Arctic atmosphere, and information on the spatial variability of heat and moisture fluxes from the arctic surface; and to demonstrate unmanned aerial system (UAS) capabilities in obtaining measurements relevant to the ARM and ASR programs, particularly for improving our understanding of Arctic clouds and aerosols.

  10. Atmospheric Mining in the Outer Solar System: Resource Capturing, Storage, and Utilization

    Science.gov (United States)

    Palaszewski, Bryan

    2014-01-01

    Atmospheric mining in the outer solar system has been investigated as a means of fuel production for high energy propulsion and power. Fusion fuels such as helium 3 and hydrogen can be wrested from the atmospheres of Uranus and Neptune and either returned to Earth or used in-situ for energy production. Helium 3 and hydrogen (deuterium, etc.) were the primary gases of interest with hydrogen being the primary propellant for nuclear thermal solid core and gas core rocket-based atmospheric flight. A series of analyses were undertaken to investigate resource capturing aspects of atmospheric mining in the outer solar system. This included the gas capturing rate for hydrogen helium 4 and helium 3, storage options, and different methods of direct use of the captured gases. Additional supporting analyses were conducted to illuminate vehicle sizing and orbital transportation issues.

  11. Westerly wind events in the tropical Pacific and their influence on the coupled ocean-atmosphere system: A review

    Science.gov (United States)

    Lengaigne, Matthieu; Boulanger, Jean-Philippe; Menkes, Christophe; Delecluse, Pascale; Slingo, Julia

    Observational and modeling aspects about Westerly Wind Events (WWEs) and their influence on the tropical Pacific ocean-atmosphere system are reviewed. WWEs are a large part of the intraseasonal zonal wind activity over the warm pool. They have typical amplitudes of 7 m s-1, zonal width of 20° longitude and duration of about 8 days. Their root causes are often a combination of various factors including the Madden-Julian Oscillation, cold surges from mid-latitudes, tropical cyclones and other mesoscale phenomena. The relationship between WWEs and the ENSO cycle is complex, involving among others the equatorial characteristics of the WWEs, the oceanic background state and the internal atmospheric variability. Both observational and modeling studies demonstrate that WWEs tend to cool the far western Pacific, shift the warm pool eastward and warm the central-eastern Pacific through the generation of Kelvin waves. They are therefore important processes for the central and eastern Pacific warming during the onset and development phase of El Niño. The strong atmospheric feedbacks that are likely to be generated by the ocean response to WWEs even suggest that a single WWE is capable of establishing the conditions under which El Niño can occur. The important role played by WWEs in the evolution and amplitude of recent El Niño events may therefore strongly limit the predictability of El Niño.

  12. Development of data management system for steam generator inspection

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Yong Moo; Im, Chang Jae; Lee, Yoon Sang; Kang, Soon Joo; An, Jong Kwan [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1994-06-01

    The data communications environment for transferring Nuclear Power Plant Steam Generator Eddy Current testing data was investigated and after connecting LAN to Hinet-F network, the remote data transfer with the speed of 56 kbps was tested successfully. Data management system for Steam Generator Eddy current testing was also developed by using HP-UX, RMB (Rock Mountain Basic) 21 figs, 13 tabs, 5 refs. (Author).

  13. System and method for key generation in security tokens

    Energy Technology Data Exchange (ETDEWEB)

    Evans, Philip G.; Humble, Travis S.; Paul, Nathanael R.; Pooser, Raphael C.; Prowell, Stacy J.

    2015-10-27

    Functional randomness in security tokens (FRIST) may achieve improved security in two-factor authentication hardware tokens by improving on the algorithms used to securely generate random data. A system and method in one embodiment according to the present invention may allow for security of a token based on storage cost and computational security. This approach may enable communication where security is no longer based solely on onetime pads (OTPs) generated from a single cryptographic function (e.g., SHA-256).

  14. Embedding the Form Generator in a Content Management System

    Science.gov (United States)

    Delgado, A.; Wicenec, A.; Delmotte, N.; Tejero, A.

    2008-08-01

    Given the tremendous amount of data generated by ESO's telescopes and the rapid evolution of the World Wide Web, the ESO archive web interface needs to offer more flexible services and advanced functionalities to a growing community of users all over the world. To achieve this endeavour, a query form generator is being developed inside a Content Management System. We present here a progress report.

  15. Development of data management system for steam generator inspection

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Yong Moo; Im, Chang Jae; Lee, Yoon Sang; Kang, Soon Joo; An, Jong Kwan [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1994-06-01

    The data communications environment for transferring Nuclear Power Plant Steam Generator Eddy Current testing data was investigated and after connecting LAN to Hinet-F network, the remote data transfer with the speed of 56 kbps was tested successfully. Data management system for Steam Generator Eddy current testing was also developed by using HP-UX, RMB (Rock Mountain Basic) 21 figs, 13 tabs, 5 refs. (Author).

  16. Developing a pulse trigger generator for a three-electrode spark-gap switch in a transversely excited atmospheric CO2 laser

    Science.gov (United States)

    Wang, Jingyuan; Guo, Lihong; Zhang, Xingliang

    2016-04-01

    To improve the probability and stability of breakdown discharge in a three-electrode spark-gap switch for a high-power transversely excited atmospheric CO2 laser and to improve the efficiency of its trigger system, we developed a high-voltage pulse trigger generator based on a two-transistor forward converter topology and a multiple-narrow-pulse trigger method. Our design uses a narrow high-voltage pulse (10 μs) to break down the hyperbaric gas between electrodes of the spark-gap switch; a dry high-voltage transformer is used as a booster; and a sampling and feedback control circuit (mainly consisting of a SG3525 and a CD4098) is designed to monitor the spark-gap switch and control the frequency and the number of output pulses. Our experimental results show that this pulse trigger generator could output high-voltage pulses (number is adjusted) with an amplitude of >38 kV and a width of 10 μs. Compared to a conventional trigger system, our design had a breakdown probability increased by 2.7%, an input power reduced by 1.5 kW, an efficiency increased by 0.12, and a loss reduced by 1.512 kW.

  17. Study of thermoelectric systems applied to electric power generation

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, A.; Vian, J.G.; Astrain, D.; Martinez, A. [Dpto. Ingenieria Mecanica, Energetica y de Materiales, Universidad Publica de Navarra, Pamplona (Spain)

    2009-05-15

    A computational model has been developed in order to simulate the thermal and electric behavior of thermoelectric generators. This model solves the nonlinear system of equations of the thermoelectric and heat transfer equations. The inputs of the program are the thermoelectric parameters as a function of temperature and the boundary conditions, (room temperature and residual heat flux). The outputs are the temperature values of all the elements forming the thermoelectric generator, (performance, electric power, voltage and electric current generated). The model solves the equation system using the finite difference method and semi-empirical expressions for the convection coefficients. A thermoelectric electric power generation test bench has been built in order to validate and determine the accuracy of the computational model, which maximum error is lower than 5%. The objective of this study is to create a design tool that allows us to solve the system of equations involved in the electric generation process without needing to impose boundary conditions that are not known in the design phase, such as the temperature of the Peltier modules. With the computational model, we study the influence of the heat flux supplied as well as the room temperature on the electric power generated. (author)

  18. Anosov C-systems and random number generators

    Science.gov (United States)

    Savvidy, G. K.

    2016-08-01

    We further develop our previous proposal to use hyperbolic Anosov C-systems to generate pseudorandom numbers and to use them for efficient Monte Carlo calculations in high energy particle physics. All trajectories of hyperbolic dynamical systems are exponentially unstable, and C-systems therefore have mixing of all orders, a countable Lebesgue spectrum, and a positive Kolmogorov entropy. These exceptional ergodic properties follow from the C-condition introduced by Anosov. This condition defines a rich class of dynamical systems forming an open set in the space of all dynamical systems. An important property of C-systems is that they have a countable set of everywhere dense periodic trajectories and their density increases exponentially with entropy. Of special interest are the C-systems defined on higher-dimensional tori. Such C-systems are excellent candidates for generating pseudorandom numbers that can be used in Monte Carlo calculations. An efficient algorithm was recently constructed that allows generating long C-system trajectories very rapidly. These trajectories have good statistical properties and can be used for calculations in quantum chromodynamics and in high energy particle physics.

  19. The atmospheric transparency measured with a LIDAR system at the Telescope Array experiment

    CERN Document Server

    Tomida, Takayuki; Arai, Takahito; Benno, Takuya; Chikawa, Michiyuki; Doura, Koji; Fukushima, Masaki; Hiyama, Kazunori; Honda, Ken; Ikeda, Daisuke; Matthews, John N; Nakamura, Toru; Oku, Daisuke; Sagawa, Hiroyuki; Tokuno, Hisao; Tameda, Yuichiro; Thomson, Gordon B; Tsunesada, Yoshiki; Udo, Shigeharu; Ukai, Hisashi; 10.1016/j.nima.2011.07.012

    2011-01-01

    An atmospheric transparency was measured using a LIDAR with a pulsed UV laser (355nm) at the observation site of Telescope Array in Utah, USA. The measurement at night for two years in $2007\\sim 2009$ revealed that the extinction coefficient by aerosol at the ground level is $0.033^{+0.016}_{-0.012} \\rm km^{-1}$ and the vertical aerosol optical depth at 5km above the ground is $0.035^{+0.019}_{-0.013}$. A model of the altitudinal aerosol distribution was built based on these measurements for the analysis of atmospheric attenuation of the fluorescence light generated by ultra high energy cosmic rays.

  20. Development of large wind energy power generation system

    Science.gov (United States)

    1985-01-01

    The background and development of an experimental 100 kW wind-energy generation system are described, and the results of current field tests are presented. The experimental wind turbine is a two-bladed down-wind horizontal axis propeller type with a 29.4 m diameter rotor and a tower 28 m in height. The plant was completed in March, 1983, and has been undergoing trouble-free tests since then. The present program calls for field tests during two years from fiscal 1983 to 1984. The development of technologies relating to the linkage and operation of wind-energy power generation system networks is planned along with the acquisition of basic data for the development of a large-scale wind energy power generation system.

  1. Mata—information generation in distributed information system

    Institute of Scientific and Technical Information of China (English)

    苏健; 高济

    2002-01-01

    The authors discuss the concept of meta-information which is the desription of information system or its subsystems,and proposes algorithms for meta-information generation.Meta-information can be generated in parallel mode and network computation can be used to accelerate meta-information generation.Most existing rough set methods assume information system to be centralized and cannot be applied directly in distributed information system.Data integration ,which is costly,is necessary for such existing methods.However,meta-information integration will eliminate the need of data integration in many cases,since many rough set operations can be done straightforward based on meta-information,and many existing methods can be modified based on meta-information.

  2. Meta-information generation in distributed information system

    Institute of Scientific and Technical Information of China (English)

    苏健; 高济

    2002-01-01

    The authors discuss the concept of meta-information which is the description of information system or its subsystems, and proposes algorithms for meta-information generation. Meta-information can be generated in parallel mode and network computation can be used to accelerate meta-information generation. Most existing rough set methods assume information system to be centralized and cannot be applied directly in distributed information system. Data integration, which is costly, is necessary for such existing methods. However, meta-information integration will eliminate the need of data integration in many cases, since many rough set operations can be done straightforward based on meta-information, and many existing methods can be modified based on meta-information.

  3. Modeling and Parameter Estimation of a Small Wind Generation System

    Directory of Open Access Journals (Sweden)

    Carlos A. Ramírez Gómez

    2013-11-01

    Full Text Available The modeling and parameter estimation of a small wind generation system is presented in this paper. The system consists of a wind turbine, a permanent magnet synchronous generator, a three phase rectifier, and a direct current load. In order to estimate the parameters wind speed data are registered in a weather station located in the Fraternidad Campus at ITM. Wind speed data were applied to a reference model programed with PSIM software. From that simulation, variables were registered to estimate the parameters. The wind generation system model together with the estimated parameters is an excellent representation of the detailed model, but the estimated model offers a higher flexibility than the programed model in PSIM software.

  4. Vector radiative transfer numerical model of coupled ocean-atmosphere system using matrix-operator method

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A vector radiative transfer numerical model of the coupled ocean-atmosphere system is developed based on the matrix-operator method, which is named PCOART. Using the Fourier analysis, the vector radiative transfer equation (VRTE) is separated into a set of equations depending only on the observa-tion zenith angle. Using the Gaussian-Quadrature method, VRTE is finally transferred into the matrix equation solved by the adding-doubling method. According to the reflective and refractive properties of the ocean-atmosphere interface, the vector radiative transfer numerical model of the ocean and at-mosphere is coupled in PCOART. Compared with the exact Rayleigh scattering look-up tables of MODIS (Moderate-resolution Imaging Spectroradiometer), it is shown that PCOART is an exactly numerical model, and the processing methods of the multi-scattering and polarization are correct. Also, validated with the standard problems of the radiative transfer in water, it is shown that PCOART can be used to calculate the underwater radiative transfer problems. Therefore, PCOART is a useful tool for exactly calculating the vector radiative transfer of the coupled ocean-atmosphere system, which can be used to study the polarization properties of the radiance in the whole ocean-atmosphere system and the remote sensing of the atmosphere and ocean.

  5. Vector radiative transfer numerical model of coupled ocean-atmosphere system using matrix-operator method

    Institute of Scientific and Technical Information of China (English)

    HE XianQiang; PAN DeLu; BAI Yan; ZHU QianKun; GONG Fang

    2007-01-01

    A vector radiative transfer numerical model of the coupled ocean-atmosphere system is developed based on the matrix-operator method,which is named PCOART.Using the Fourier analysis,the vector radiative transfer equation (VRTE) is separated into a set of equations depending only on the observation zenith angle.Using the Gaussian-Quadrature method,VRTE is finally transferred into the matrix equation solved by the adding-doubling method.According to the reflective and refractive properties of the ocean-atmosphere interface,the vector radiative transfer numerical model of the ocean and atmosphere is coupled in PCOART.Compared with the exact Rayleigh scattering look-up tables of MODIS (Moderate-resolution Imaging Spectroradiometer),it is shown that PCOART is an exactly numerical model,and the processing methods of the multi-scattering and polarization are correct.Also,validated with the standard problems of the radiative transfer in water,it is shown that PCOART can be used to calculate the underwater radiative transfer problems.Therefore,PCOART is a useful tool for exactly calculating the vector radiative transfer of the coupled ocean-atmosphere system,which can be used to study the polarization properties of the radiance in the whole ocean-atmosphere system and the remote sensing of the atmosphere and ocean.

  6. Simulation on Cooling System of Automotive Waste Heat Thermoelectric Generator

    Directory of Open Access Journals (Sweden)

    Xiaohong Yuan

    2013-06-01

    Full Text Available The cooling system of automobile waste heat Thermoelectric Generator (TEG is researched in the study. Integrated model of cooling system and vehicle is built based on GT-Cool, analysis of the different cooling ways shows that when using independent cooling system, the ratio between power consumption and output is high and system performance is poor; By using integrated cooling system, the expectation of keep constant engine warm up time and synchronous change of water temperature between different tanks is realized after water tanks are improved.

  7. Grid-connected inverter for wind power generation system

    Institute of Scientific and Technical Information of China (English)

    YANG Yong; RUAN Yi; SHEN Huan-qing; TANG Yan-yan; YANG Ying

    2009-01-01

    In wind power generation system the grid-connected inverter is an important section for energy conversion and transmission, of which the performance has a direct influence on the entire wind power generation system. The mathematical model of the grid-connected inverter is deduced firstly. Then, the space vector pulse width modulation (SVPWM) is analyzed. The power factor can be controlled close to unity, leading or lagging, which is realized based on PI-type current controller and grid voltage vector-oriented control. The control strategy is verified by the simulation and experimental results with a good sinusoidal current, a small harmonic component and a fast dynamic response.

  8. Induction generator-induction motor wind-powered pumping system

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, M.S.; Lyra, R.O.C.; Silva, S.R. [CPDEE - UFMG, Belo Horizonte (Brazil)

    1997-12-31

    The energy storage matter plays an important role in wind-electric conversion systems for isolated applications. Having that in mind, two different approaches can be basically considered: either the immediate conversion of the generated electric energy, as in a water pumping system or electric energy storage for later use, as in a battery charging system. Due to some features such as no need of an external reactive power source and, sometimes, a gearbox, permanent-magnet synchronous generators have been broadly used in low rated power isolated systems. Despite that, system performance can be affected when the generator is feeding an inductive load (e.g., an induction motor) under variable-speed-variable-frequency operational conditions. Since there is no effective flux control, motor overload may occur at high wind speeds. Thus, good system performance can be obtained through additional control devices which may increase system cost. Although being rugged and cheap, induction machines always work as a reactive power drain; therefore, they demand an external reactive power source. Considering that, reactive static compensators appear as an attractive alternative to the cost x performance problem. In addition to that, different control strategies can be used so that system performance can be improved.

  9. Thickness of the electron atmosphere in large nuclear systems

    Science.gov (United States)

    Pacheco, A. F.; Sañudo, J.

    1986-03-01

    Using the relativistic Thomas-Fermi model and the virial theorem it is found that the thickness of the electron skin outside a large nuclear system is given by S⋍6.73 n-1/3, n being the electron density inside the nucleus. On leave from Departamento de Fisica Teorica, Facultad de Ciencias, Universidad de Zaragoza, 50009 Zaragoza, Spain.

  10. Fuels and cycles for the fourth generation systems; Combustibles et cycles pour les systemes de 4. generation

    Energy Technology Data Exchange (ETDEWEB)

    Brossard, Ph. [CEA Saclay, Dir. du Developpement et de l' Innovation Nucleares (DEN/DDIN), 91 - Gif Sur Yvette (France)

    2003-07-01

    This paper presented during the Cea Seminar on the nuclear systems of the future deals with the fuels and cycles of the fourth generation systems. Four goal areas have been defined for these systems: sustainable for the environment, economical for the investment, safety and reliability, a better protection against the proliferation. The different fuels and cycles of the research programs are detailed. (A.L.B.)

  11. On the atmospheric chemistry of NO2 - O3 systems; a laboratory study.

    NARCIS (Netherlands)

    Verhees, P.W.C.

    1986-01-01

    In this dissertation a laboratory study dealing with the atmospheric chemistry of NO 2 -O 3 systems is described. Knowledge of this system is relevant for a better understanding of a number of air pollution problems, particularly th

  12. Atmospheric radiative flux divergence from Clouds and Earth Radiant Energy System (CERES)

    Science.gov (United States)

    Smith, Louis G.; Charlock, Thomas P.; Crommelynk, D.; Rutan, David; Gupta, Shashi

    1990-01-01

    A major objective of the Clouds and Earth Radiant Energy System (CERES) is the computation of vertical profiles through the atmosphere of the divergence of radiation flux, with global coverage. This paper discusses the need for radiation divergence and presents some options for its inference from CERES measurements and other data from the Earth Observating System.

  13. Modeling of brushless dc generating systems using diakoptics

    Science.gov (United States)

    Vadher, Vinod; Gregory, Keith; Kettleborough, J. G.; Smith, Ivor R.

    1993-01-01

    The mathematical modeling of a brushless dc generator is described, as an illustration of the application of diakoptic techniques to the analysis of small-scale electrical power supply systems. Modeling of the generator and its output rectifier is accomplished using an established matrix technique that accounts for the continuously changing conduction pattern of the diode bridge network. The advantages of using diakoptics are introduced when consideration is given to the main generator linked to its exciter and to the automatic voltage regulator and permanent magnet generator which are often included in a complete unit. A solution algorithm is presented for this overall arrangement and a comparison is made between theoretical and practical results for a typical 3-stage 4000 rev/min 10.3 kW 28 V unit.

  14. Model based document and report generation for systems engineering

    Science.gov (United States)

    Delp, C.; Lam, D.; Fosse, E.; Lee, Cin-Young

    As Model Based Systems Engineering (MBSE) practices gain adoption, various approaches have been developed in order to simplify and automate the process of generating documents from models. Essentially, all of these techniques can be unified around the concept of producing different views of the model according to the needs of the intended audience. In this paper, we will describe a technique developed at JPL of applying SysML Viewpoints and Views to generate documents and reports. An architecture of model-based view and document generation will be presented, and the necessary extensions to SysML with associated rationale will be explained. A survey of examples will highlight a variety of views that can be generated, and will provide some insight into how collaboration and integration is enabled. We will also describe the basic architecture for the enterprise applications that support this approach.

  15. COMBINED SYSTEMS OF ENERGY GENERATION – A CHARACTERISATION AND CLASSIFICATION

    Directory of Open Access Journals (Sweden)

    Jan Gilewski

    2014-09-01

    Full Text Available The study presents issues concerning technical solutions of combined systems of energy generation which can be used primarily in low-level power plants, installed in various types of public utility sites. A detailed description is given of selected ways of powering combined energy generation systems, presenting conceptual outlines of their operation and information on their advantages, disadvantages and applications. The following systems are introduced: gas-steam, back-pressure steam turbine, extraction-condensing steam turbine, gas turbine, gas microturbine, Stirling engine, fuel cells and internal combustion piston engine. Moreover, the study addresses economic aspects of energy generation in combined systems, discussing different methodologies of cost calculation, including the one used by the European Union. The article also gives a detailed review of piston engine combined-system aggregates available in the Polish market. Type series of associated systems designed for low-power appliances are shown, produced by Polish and foreign companies such as Viessmann, Centrum Elektroniki Stosowanej CES, H. Cegielski – Poznań, KWE Technika Energetyczna, TEDOM Poland or the EPS System.

  16. Micro-Turbine Generation Control System Optimization Using Evolutionary algorithm

    Directory of Open Access Journals (Sweden)

    Mohanraj B S

    2014-10-01

    Full Text Available Distribution systems management is becoming an increasingly complicated issue due to the introduction of new technologies, new energy trading strategies, and new deregulated environment. In the new deregulated energy market and considering the incentives coming from the technical and economical fields, it is reasonable to consider Distributed Generation (DG as a viable option to solve the lacking electric power supply problem. This paper presents a mathematical distribution system planning model considering three planning options to system expansion and to meet the load growth requirements with a reasonable price as well as the system power quality problems. DG is introduced as an attractive planning option in competition with voltage regulator devices and Interruptible load. This paper presents a dynamic modelling and simulation of a high speed single shaft micro-turbine generation (MTG system for grid connected operation and shows genetic algorithm (GA role in improvement of control system operation. The model is developed with the consideration of the main parts including: compressor-turbine, permanent magnet (PM generator, three phase bridge rectifier and inverter. The simulation results show the capability of Genetic Algorithm for controlling MTG system. The model is developed in Mat lab / Simulink.

  17. Research and development of evaluation system for photovoltaic power generation system. Survey on research and development of solar cell evaluation system; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on R and D of solar cell evaluation systems in fiscal 1994. The performance/reliability evaluation subcommittee continuously analyzed technical issues and discussed solution measures from the last fiscal year. On development of performance evaluation methods, improvement of measurement accuracy for laminated solar cells is the study issue to be solved. Although laminated solar cells are measured by multiple light source solar simulator, difficult spectrum compensation causes measurement errors. Collection and analysis of data for determining atmospheric conditions, and outdoor measurement experiment under the atmospheric conditions for reference solar light were carried out. The study on incident angle characteristics of laminated solar cells clarified that the deviation from COS characteristics is 1.0% or less at an incident angle of 30{degree}. The study on generated energy in solar cell module level in field clarified that generated energy and generation efficiency are proportional to intensity of solar radiation. 1 tab.

  18. Evaluation of medium-range weather forecasts about Korea Institute of Atmospheric Prediction Systems (KIAPS) Integrated Model System (KIM)

    Science.gov (United States)

    Lee, J.; Seol, K. H.

    2015-12-01

    The Korea Institute of Atmospheric Prediction Systems (KIAPS) is a government funded non-profit research and development institute located in Seoul, South Korea. KIAPS was established in 2011 by the Korea Meteorological Administration, KIAPS' primary sponsor. KIAPS is developing the KIAPS Integrated Model System (KIM), a backbone for the next-generation operational global numerical weather prediction (NWP) system. The KIM will be a unified model that can be used for global modeling as well as local areas, particularly optimized to topographic and meteorological features of the Korean Peninsula. We have been completed developing major model components based on KIAPS own research and release the KIAPS beta version model on September 2014. We evaluated the results of KIM by using verification system developed KIAPS, it is composed of standard verification score based on WMO report. The system consists of four parts: verification against analysis, observations, vertical verification and quantitative precipitation forecasts. The results of verification against analysis, we found that increase of error for temperature under 700 hPa. In case of MSLP, poor performance except for tropical region is represented, and the increase of error for geopotential height is shown in tropical region. For verification against observations, positive bias is represented for upper level geopotential height, for low level wind speed in tropical region in summer, for all level wind speed in Northern Hemisphere in winter, and for specific humidity in Northern Hemisphere in summer. As previously stated about the result against analysis, cold bias for low level temperature is shown in Northern Hemisphere in summer. In case of verification for rain about KIM, the model value is underestimated in heavy rain category in summer, on the contrary, that is overestimated in heavy rain category in winter. Overall, there is overestimation in ocean for all models. Our findings indicate that continuing

  19. Comparison of atmospheric transport calculations over complex terrain using a mobile profiling system and rawinsondes

    Science.gov (United States)

    Cox, Robert M.; Cogan, James; Sontowski, John; Dougherty, Catherine M.; Fry, Richard N., Jr.; Smith, Thomas J.

    2000-12-01

    A comparison of atmospheric transport and dispersion calculations over complex terrain was investigated using a mobile profiling system (MPS) versus standard meteorological balloons. Meteorological and sulfur hexafluoride (SF6) concentration data were collected and used to evaluate the performance of a transport and diffusion model coupled with a mass consistency wind field model. Meteorological data were collected throughout April 1995, and parts of August 1995. Both meteorological and concentration data were measured in December 1995. Once the models were validated, the comparison of performance with different upper-air data were accomplished. The models used included the SCIPUFF (Second-order Closure Integrated Puff) transport and diffusion model and the MINERVE mass consistency wind model. Evaluation of the models was focused primarily on their effectiveness as a short-term (one to four hours) predictive tool. These studies showed how the combination of weather and transport models could be used to help direct emergency response following a hazardous material release. The models were used in tandem to direct the deployment of mobile sensors intended to intercept and measure tracer clouds. The MINERVE model was validated for the specific terrain of interest using April 1995 data. The capability of SCIPUFF driven by realistic three-dimensional wind fields generated by MINERVE is demonstrated using data collected in December 1995.

  20. Evaluating Land-Atmosphere Moisture Feedbacks in Earth System Models With Spaceborne Observations

    Science.gov (United States)

    Levine, P. A.; Randerson, J. T.; Lawrence, D. M.; Swenson, S. C.

    2016-12-01

    We have developed a set of metrics for measuring the feedback loop between the land surface moisture state and the atmosphere globally on an interannual time scale. These metrics consider both the forcing of terrestrial water storage (TWS) on subsequent atmospheric conditions as well as the response of TWS to antecedent atmospheric conditions. We designed our metrics to take advantage of more than one decade's worth of satellite observations of TWS from the Gravity Recovery and Climate Experiment (GRACE) along with atmospheric variables from the Atmospheric Infrared Sounder (AIRS), the Global Precipitation Climatology Project (GPCP), and Clouds and the Earths Radiant Energy System (CERES). Metrics derived from spaceborne observations were used to evaluate the strength of the feedback loop in the Community Earth System Model (CESM) Large Ensemble (LENS) and in several models that contributed simulations to Phase 5 of the Coupled Model Intercomparison Project (CMIP5). We found that both forcing and response limbs of the feedback loop were generally stronger in tropical and temperate regions in CMIP5 models and even more so in LENS compared to satellite observations. Our analysis suggests that models may overestimate the strength of the feedbacks between the land surface and the atmosphere, which is consistent with previous studies conducted across different spatial and temporal scales.

  1. Scaling laws for perturbations in the ocean–atmosphere system following large CO2 emissions

    Directory of Open Access Journals (Sweden)

    N. Towles

    2015-07-01

    Full Text Available Scaling relationships are found for perturbations to atmosphere and ocean variables from large transient CO2 emissions. Using the Long-term Ocean-atmosphere-Sediment CArbon cycle Reservoir (LOSCAR model (Zeebe et al., 2009; Zeebe, 2012b, we calculate perturbations to atmosphere temperature, total carbon, ocean temperature, total ocean carbon, pH, alkalinity, marine-sediment carbon, and carbon-13 isotope anomalies in the ocean and atmosphere resulting from idealized CO2 emission events. The peak perturbations in the atmosphere and ocean variables are then fit to power law functions of the form of γ DαEβ, where D is the event duration, E is its total carbon emission, and γ is a coefficient. Good power law fits are obtained for most system variables for E up to 50 000 PgC and D up to 100 kyr. Although all of the peak perturbations increase with emission rate E/D, we find no evidence of emission-rate-only scaling, α + β = 0. Instead, our scaling yields α + β ≃ 1 for total ocean and atmosphere carbon and 0 < α + β < 1 for most of the other system variables.

  2. An Analog Trigger System for Atmospheric Cherenkov Telescopes

    CERN Document Server

    Barcelo, M; Bigas, O Blanch; Boix, J; Delgado, C; Herranz, D; Lopez-Coto, R; Martinez, G

    2013-01-01

    Arrays of Cherenkov telescopes typically use multi-level trigger schemes to keep the rate of random triggers from the night sky background low. At a first stage, individual telescopes produce a trigger signal from the pixel information in the telescope camera. The final event trigger is then formed by combining trigger signals from several telescopes. In this poster, we present a possible scheme for the Cherenkov Telescope Array telescope trigger, which is based on the analog pulse information of the pixels in a telescope camera. Advanced versions of all components of the system have been produced and working prototypes have been tested, showing a performance that meets the original specifications. Finally, issues related to integrating the trigger system in a telescope camera and in the whole array will be dealt with.

  3. A high precision technique to correct for residual atmospheric dispersion in high-contrast imaging systems

    CERN Document Server

    Pathak, P; Jovanovic, N; Lozi, J; Martinache, F; Minowa, Y; Kudo, T; Takami, H; Hayano, Y; Narita, N

    2016-01-01

    Direct detection and spectroscopy of exoplanets requires high contrast imaging. For habitable exoplanets in particular, located at small angular separation from the host star, it is crucial to employ small inner working angle (IWA) coronagraphs that efficiently suppress starlight. These coronagraphs, in turn, require careful control of the wavefront which directly impacts their performance. For ground-based telescopes, atmospheric refraction is also an important factor, since it results in a smearing of the PSF, that can no longer be efficiently suppressed by the coronagraph. Traditionally, atmospheric refraction is compensated for by an atmospheric dispersion compensator (ADC). ADC control relies on an a priori model of the atmosphere whose parameters are solely based on the pointing of the telescope, which can result in imperfect compensation. For a high contrast instrument like the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system, which employs very small IWA coronagraphs, refraction-induced sm...

  4. Determination of the species generated in atmospheric-pressure laser-induced plasmas by mass spectrometry techniques

    CERN Document Server

    Valle, F; Apiñaniz, J I; Carpentier, A V; Albaneda, M Sánchez; Roso, L; Raposo, C; Padilla, C; Conde, A Peralta

    2015-01-01

    We present temporal information obtained by mass spectrometry techniques about the evolution of plasmas generated by laser filamentation in air. The experimental setup used in this work allowed us to study not only the dynamics of the filament core but also of the energy reservoir that surrounds it. Furthermore, valuable insights about the chemistry of such systems like the photofragmentation and/or formation of molecules were obtained. The interpretation of the experimental results are supported by PIC (particle in cell) simulations.

  5. Power fluctuations smoothing and regulations in wind turbine generator systems

    Science.gov (United States)

    Babazadehrokni, Hamed

    Wind is one of the most popular renewable energy sources and it has the potential to become the biggest energy source in future. Since the wind does not always blow constantly, the output wind power is not constant which may make some problem for the power grid. According to the grid code which is set by independent system operator, ISO, wind turbine generator systems need to follow some standards such as the predetermined acceptable power fluctuations. In order to smooth the output powers, the energy storage system and some power electronics modules are employed. The utilized power electronics modules in the wind turbine system can pursue many different goals, such as maintaining the voltage stability, frequency stability, providing the available and predetermined output active and reactive power. On the other side, the energy storage system can help achieving some of these goals but its main job is to store the extra energy when not needed and release the stored energy when needed. The energy storage system can be designed in different sizes, material and also combination of different energy storage systems (hybrid designs). Combination of power electronics devises and also energy storage system helps the wind turbine systems to smooth the output power according to the provided standards. In addition prediction of wind speed may improve the performance of wind turbine generator systems. In this research study all these three topics are studied and the obtained results are written in 10 papers which 7 of them are published and three of them are under process.

  6. Procurement of a fully licensed radioisotope thermoelectric generator transportation system

    Science.gov (United States)

    Adkins, Harold E.; Bearden, Thomas E.

    1991-01-01

    A fully licensed transportation system for Radioisotope Thermoelectric Generators and Light-Weight Radioisotope Heater Units is currently being designed and built. The system will comply with all applicable U.S. Department of Transportation regulations without the use of a ``DOE Alternative.'' The U.S. Department of Transportation has special ``double containment'' requirements for plutonium. The system packaging uses a doubly contained ``bell jar'' concept. A refrigerated trailer is used for cooling the high-heat payloads. The same packaging is used for both high- and low-heat payloads. The system is scheduled to be available for use by mid-1992.

  7. Electric Generator in the System for Damping Oscillations of Vehicles

    Science.gov (United States)

    Serebryakov, A.; Kamolins, E.; Levin, N.

    2017-04-01

    The control systems for the objects of industry, power generation, transport, etc. are extremely complicated; functional efficiency of these systems determines to a great extent the safe and non-polluting operation as well as convenience of service and repair of such objects. The authors consider the possibility to improve the efficiency of systems for damping oscillations in transport using a combination of electrical (generators of rotational and linear types) and hydraulic means. Better efficiency of functioning is achieved through automatic control over the operational conditions of such a system in order to make it adaptive to variations in the road profile and ambient temperature; besides, it is possible to produce additional electric energy.

  8. Collaborative process control: Observation of tracks generated by PLM system

    CERN Document Server

    Elkadiri, Soumaya; Delattre, Miguel; Bouras, Abdelaziz

    2008-01-01

    This paper aims at analyzing the problems related to collaborative work using a PLM system. This research is mainly focused on the organisational aspects of SMEs involved in networks composed of large companies, subcontractors and other industrial partners. From this analysis, we propose the deployment of an approach based on an observation process of tracks generated by PLM system. The specific contributions are of two fold. First is to identify the brake points of collaborative work. The second, thanks to the exploitation of generated tracks, it allows reducing risks by reacting in real time to the incidents or dysfunctions that may occur. The overall system architecture based on services technology and supporting the proposed approach is described, as well as associated prototype developed using an industrial PLM system.

  9. Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Faress Rahman; Nguyen Minh

    2004-01-04

    This report summarizes the work performed by Hybrid Power Generation Systems, LLC (HPGS) during the July 2003 to December 2003 reporting period under Cooperative Agreement DE-FC26-01NT40779 for the U. S. Department of Energy, National Energy Technology Laboratory (DOE/NETL) entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. The main objective of this project is to develop and demonstrate the feasibility of a highly efficient hybrid system integrating a planar Solid Oxide Fuel Cell (SOFC) and a micro-turbine. In addition, an activity included in this program focuses on the development of an integrated coal gasification fuel cell system concept based on planar SOFC technology. Also, another activity included in this program focuses on the development of SOFC scale up strategies.

  10. Dimensioning of Photovoltaic Generation Systems Located in Medellin City

    Directory of Open Access Journals (Sweden)

    Laura Herrera

    2013-11-01

    Full Text Available Photovoltaic systems are one of the most efficient solutions to the energy crisis of the last decades. The implementation of these systems will be economically feasible in most cases, due to extensive number of advantages that they exhibit. However, for the sake of better economic performance, it is important to generate different strategies for their management. This paper presents an optimization strategy based on the redistribution of power generated, which seeks to stop spending as it is produced to take advantage of those times when energy rates are higher, making use of a storage system. The steps for the photovoltaic system design with these criteria and economic analysis will be presented.

  11. Modelling of Steam Generating Paraboloidal dish Solar Thermal Power System

    Energy Technology Data Exchange (ETDEWEB)

    Siangsukone, P.; Lovegrove, K.

    2006-07-01

    The Australian National University (ANU) has a 400m2 Paraboloidal dish solar concentrator system, informally named the Big Dish that produces superheated steam via a receiver mounted monotube boiler connected to 50kWe steam engine for electricity generation. This paper describes an investigation of the system and its components modelled using the TRNYSYS transient system simulation package. The system was modelled in the context of performance assessment for multiple dishes, central generation Rankine cycle power plants. Five new custom components; paraboloidal dish collector, steam cavity receiver, steam line or feedwater line, steam engine, and pressure drop calculator, were developed for the TRNSYS deck file constructed for this study. Validation tests were performed by comparing with the latest experimental results measured with a 1-minute time step and good agreement, with errors less than 10%, has been found. (Author)

  12. Performance optimization for doubly-fed generation systems

    Science.gov (United States)

    Bhowmik, Shibashis

    A variable speed generation (VSG) system converts energy from a variable resource such as wind or water flow into variable rotational mechanical energy of a turbine or a similar device that converts translational kinetic energy into rotational mechanical energy. The mechanical energy is then converted into electrical energy by an electrical generator. Presently available and proposed generators include systems based mainly on dc machines, synchronous and induction machine technology as well as reluctance machines. While extracting more energy from the resource, most proposed VSG systems suffer a cost disadvantage due to the required rating of the power electronic interface. This cost penalty may eventually render the additional energy capture meaningless. Thus, reducing the cost of the power electronic hardware is essential for VSG systems to achieve viable and competitive $/kWh ratios when compared to fossil fuel-based generating systems. A variable speed constant frequency (VSCF) system and controller are proposed that utilize a doubly-fed machine (DFM) as the energy conversion device. The system includes a power converter that provides the current excitation for the control winding of the DFM. Both the magnitude and frequency of the excitation is determined by an adaptive model-based controller which maximizes the power flow from the mechanical turbine to the electrical grid and reduces the generator losses by maintaining the maximum efficiency point throughout the mechanical input power range. The proposed strategy has been experimentally verified in controlled laboratory conditions for a proof-of-concept brushless doubly-fed machine (BDFM) system of 1500 Watts power rating. Issues relating to power converter development and its incorporation in the system have been investigated. The controller and circuit design of a four quadrant, AC/AC power converter is presented and a novel sensorless current controller for the active rectifier stage is presented in detail

  13. Generation of burst time plans for the Intelsat TDMA system

    Science.gov (United States)

    Trusty, P. A.; King, C. A.; Roach, P. W.

    In the Intelsat time-division multiple-access (TDMA) system, the burst time plan (BTP) contains the assignments of traffic and reference bursts, common acquisition windows, and test slots to time slots within the TDMA frame for a given network. Generation of the BTP involves the processes of sub-burst formation, burst formation, reference burst assignments, and burst scheduling. BTP information is transferred to the individual reference and traffic stations in the form of a master time plan (MTP) and a condensed time plan (CTP). This paper describes algorithms which have been developed for each of the BTP generation processes, as well as those algorithms and procedures used to generate the MTPs and CTPs. A software system which implements these algorithms is also discussed.

  14. Wind turbine generator interaction with diesel generators on an isolated power system

    Science.gov (United States)

    Scott, G. W.; Wilreker, V. F.; Shaltens, R. K.

    1983-01-01

    The results of a dynamic interaction investigation to characterize any disturbances caused by interfacing the Mod 0A wind turbine (150 kW configuration) with the Block Island utility diesel generator grid are reported. The tests were run when only two diesel generators were on line, and attention was given to power, frequency, and voltage time profiles. The interconnected system was examined in the start-up and synchronization phase, normal shutdown and cut-out of the wind turbine, during fixed pitch generation, and during variable pitch operation. Governors were installed on the diesel generators to accommodate the presence of wind-derived electricity. The blade pitch control was set to maintain power at 150 kW or below. Power and voltage transients were insignificant during start-up and shutdown, and frequency aberrations were within the range caused by load fluctuations. It is concluded that wind turbine generation can be successfully implemented by an isolated utility, even with a significant penetration to the total grid output.

  15. Calculating the balance between atmospheric CO2 drawdown and organic carbon oxidation in subglacial hydrochemical systems

    Science.gov (United States)

    Graly, Joseph A.; Drever, James I.; Humphrey, Neil F.

    2017-04-01

    In order to constrain CO2 fluxes from biogeochemical processes in subglacial environments, we model the evolution of pH and alkalinity over a range of subglacial weathering conditions. We show that subglacial waters reach or exceed atmospheric pCO2 levels when atmospheric gases are able to partially access the subglacial environment. Subsequently, closed system oxidation of sulfides is capable of producing pCO2 levels well in excess of atmosphere levels without any input from the decay of organic matter. We compared this model to published pH and alkalinity measurements from 21 glaciers and ice sheets. Most subglacial waters are near atmospheric pCO2 values. The assumption of an initial period of open system weathering requires substantial organic carbon oxidation in only 4 of the 21 analyzed ice bodies. If the subglacial environment is assumed to be closed from any input of atmospheric gas, large organic carbon inputs are required in nearly all cases. These closed system assumptions imply that order of 10 g m-2 y-1 of organic carbon are removed from a typical subglacial environment—a rate too high to represent soil carbon built up over previous interglacial periods and far in excess of fluxes of surface deposited organic carbon. Partial open system input of atmospheric gases is therefore likely in most subglacial environments. The decay of organic carbon is still important to subglacial inorganic chemistry where substantial reserves of ancient organic carbon are found in bedrock. In glaciers and ice sheets on silicate bedrock, substantial long-term drawdown of atmospheric CO2 occurs.

  16. GPU-accelerated atmospheric chemical kinetics in the ECHAM/MESSy (EMAC Earth system model (version 2.52

    Directory of Open Access Journals (Sweden)

    M. Alvanos

    2017-10-01

    Full Text Available This paper presents an application of GPU accelerators in Earth system modeling. We focus on atmospheric chemical kinetics, one of the most computationally intensive tasks in climate–chemistry model simulations. We developed a software package that automatically generates CUDA kernels to numerically integrate atmospheric chemical kinetics in the global climate model ECHAM/MESSy Atmospheric Chemistry (EMAC, used to study climate change and air quality scenarios. A source-to-source compiler outputs a CUDA-compatible kernel by parsing the FORTRAN code generated by the Kinetic PreProcessor (KPP general analysis tool. All Rosenbrock methods that are available in the KPP numerical library are supported.Performance evaluation, using Fermi and Pascal CUDA-enabled GPU accelerators, shows achieved speed-ups of 4. 5 ×  and 20. 4 × , respectively, of the kernel execution time. A node-to-node real-world production performance comparison shows a 1. 75 ×  speed-up over the non-accelerated application using the KPP three-stage Rosenbrock solver. We provide a detailed description of the code optimizations used to improve the performance including memory optimizations, control code simplification, and reduction of idle time. The accuracy and correctness of the accelerated implementation are evaluated by comparing to the CPU-only code of the application. The median relative difference is found to be less than 0.000000001 % when comparing the output of the accelerated kernel the CPU-only code.The approach followed, including the computational workload division, and the developed GPU solver code can potentially be used as the basis for hardware acceleration of numerous geoscientific models that rely on KPP for atmospheric chemical kinetics applications.

  17. The 1-way on-line coupled atmospheric chemistry model system MECO(n – Part 1: The limited-area atmospheric chemistry model COSMO/MESSy

    Directory of Open Access Journals (Sweden)

    A. Kerkweg

    2011-06-01

    Full Text Available The numerical weather prediction model of the Consortium for Small Scale Modelling (COSMO, maintained by the German weather service (DWD, is connected with the Modular Earth Submodel System (MESSy. This effort is undertaken in preparation of a~new, limited-area atmospheric chemistry model. This model is as consistent as possible, with respect to atmospheric chemistry and related processes, with a previously developed global atmospheric chemistry general circulation model: the ECHAM/MESSy Atmospheric Chemistry (EMAC model. The combined system constitutes a new research tool, bridging the global to the meso-γ scale for atmospheric chemistry research. MESSy provides the infrastructure and includes, among others, the process and diagnostic submodels for atmospheric chemistry simulations. Furthermore, MESSy is highly flexible allowing model setups with tailor made complexity, depending on the scientific question. Here, the connection of the MESSy infrastructure to the COSMO model is documented. Previously published prototype submodels for simplified tracer studies are generalised to be plugged-in and used in the global and the limited-area model. They are used to evaluate the tracer transport characteristics of the new COSMO/MESSy model system, an important prerequisite for future atmospheric chemistry applications. A supplementary document with further details on the technical implementation of the MESSy interface into COSMO with a complete list of modifications to the COSMO code is provided.

  18. On generating neutron transport tables with the NJOY system

    Energy Technology Data Exchange (ETDEWEB)

    Caldeira, Alexandre D.; Claro, Luiz H., E-mail: alexdc@ieav.cta.br, E-mail: luizhenu@ieav.cta.br [Instituto de Estudos Avancados (IEAv), Sao Jose dos Campos, SP (Brazil)

    2013-07-01

    Incorrect values for the product of the average number of neutrons released per fission and the fission microscopic cross-section were detected in several energy groups of a neutron transport table generated with the most updated version of the NJOY system. It was verified that the problem persists when older versions of this system are utilized. Although this problem exists for, at least, ten years, it is still an open question. (author)

  19. The Second Generation High Speed Rotor Head Mounted Instrumentation System

    Science.gov (United States)

    Lewis, John; Reynolds, R. S. (Technical Monitor)

    1997-01-01

    NASA Ames Research Center has been investigating the air pressure flow of a rotor blade on a UH-60 Black Hawk helicopter in-flight. This paper will address the changes and improvements due to additional restrictions and requirements for the instrumentation system. The second generation instrumentation system was substantially larger and this allowed greatly improved accessibility to the components for ease of maintenance as well as improved gain and offset adjustment capabilities and better filtering.

  20. SABATPG-A Structural Analysis Based Automatic Test Generation System

    Institute of Scientific and Technical Information of China (English)

    李忠诚; 潘榆奇; 闵应骅

    1994-01-01

    A TPG system, SABATPG, is given based on a generic structural model of large circuits. Three techniques of partial implication, aftereffect of identified undetectable faults and shared sensitization with new concepts of localization and aftereffect are employed in the system to improve FAN algorithm. Experiments for the 10 ISCAS benchmark circuits show that the computing time of SABATPG for test generation is 19.42% less than that of FAN algorithm.

  1. Control System for a Diesel Generator and UPS Based Microgrid

    Science.gov (United States)

    Palamar, Andriy; Pettai, Elmo; Beldjajev, Viktor

    2010-01-01

    In this paper a microgrid composed of a diesel generator and two uninterruptible power supply systems with separate battery banks is introduced. The microgrid located in three academic buildings of Tallinn University of Technology. A three-level control and monitoring system for the microgrid based on the EtherNet/IP communication network is developed. In addition, a control strategy of the microgrid in the grid-connected and stand-alone mode of operation is proposed.

  2. Studying the factors affecting solar power generation systems performance ( SPGSP)

    OpenAIRE

    Jalal A Al-Tabtabaei

    2014-01-01

    Solar energy is a huge, clean and renewable source of energy. It is also available everywhere on the earth. However, there are many technical and economic difficulties need to be solved so that solar energy becomes a strong competition against the traditional energy sources. Energy from the sun can be used successfully in electric power generation systems. Depending on the climate conditions and the use of a properly designed, installing and maintained system can meet a large dema...

  3. Control System for a Diesel Generator and UPS Based Microgrid

    OpenAIRE

    Palamar, A; Pettai, E; Beldjajev, v

    2010-01-01

    In this paper a microgrid composed of a diesel generator and two uninterruptible power supply systems with separate battery banks is introduced. The microgrid located in three academic buildings of Tallinn University of Technology. A three-level control and monitoring system for the microgrid based on the EtherNet/IP communication network is developed. In addition, a control strategy of the microgrid in the grid-connected and stand-alone mode of operation is proposed

  4. Stages: A system for generating strategic alternaties for forest management.

    NARCIS (Netherlands)

    Bos, J.

    1994-01-01

    Strategic planning is important in forest management. However, it has never been described clearly in literature. In this study a framework for strategic planning was developed and based on this a STrategic Alternatives Generating System (STAGES) to support decision making in strategic planning for

  5. harmonics: generation and suppression in ac system networks

    African Journals Online (AJOL)

    2012-11-03

    Nov 3, 2012 ... HARMONICS: GENERATION AND SUPPRESSION IN AC. SYSTEM NETWORKS .... If Vs = 295V; Z = (8 + j6)Ω and δ = 2π/3, the output voltage, Vo and ... tor current assume the characteristics shown in figure. 8. The output ...

  6. Power Electronics for the Next Generation Wind Turbine System

    DEFF Research Database (Denmark)

    Ma, Ke

    This book presents recent studies on the power electronics used for the next generation wind turbine system. Some criteria and tools for evaluating and improving the critical performances of the wind power converters have been proposed and established. The book addresses some emerging problems...

  7. Power Electronics for the Next Generation Wind Turbine System

    DEFF Research Database (Denmark)

    Ma, Ke

    This book presents recent studies on the power electronics used for the next generation wind turbine system. Some criteria and tools for evaluating and improving the critical performances of the wind power converters have been proposed and established. The book addresses some emerging problems...

  8. STAGES : a system for generating strategic alternatives for forest management

    NARCIS (Netherlands)

    Bos, J.

    1994-01-01

    Strategic planning is important in forest management. However, it has never been described clearly in literature. In this study a framework for strategic planning was developed and based on this a STrategic Alternatives Generating System (STAGES) to support decision making in strategic

  9. Heat savings in energy systems with substantial distributed generation

    DEFF Research Database (Denmark)

    Østergaard, PA

    2003-01-01

    , if a certain production is required regardless of whether over-all electricity generation is sufficient. This article analyses this and although heat savings do have a negative impact on the amount of wind power the system may integrate a given moment in certain cases, associated fuel savings are notable...

  10. Kite Generator System Periodic Motion Planning Via Virtual Constraints

    OpenAIRE

    Ahmed, M; Hably, Ahmad; Bacha, Seddik

    2013-01-01

    International audience; This paper presents a new control strategy for Kite Generator System (KGS). The proposed feedback strategy is based on motion planning using the virtual constraint approach and ensures exponential orbital stability of the desired trajectory. The strategy is detailed, applied and tested via numerical simulations and showed good convergence to a desired periodic motion.

  11. Design of fault tolerant control system for steam generator using

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Myung Ki; Seo, Mi Ro [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

    1998-12-31

    A controller and sensor fault tolerant system for a steam generator is designed with fuzzy logic. A structure of the proposed fault tolerant redundant system is composed of a supervisor and two fuzzy weighting modulators. A supervisor alternatively checks a controller and a sensor induced performances to identify which part, a controller or a sensor, is faulty. In order to analyze controller induced performance both an error and a change in error of the system output are chosen as fuzzy variables. The fuzzy logic for a sensor induced performance uses two variables : a deviation between two sensor outputs and its frequency. Fuzzy weighting modulator generates an output signal compensated for faulty input signal. Simulations show that the proposed fault tolerant control scheme for a steam generator regulates well water level by suppressing fault effect of either controllers or sensors. Therefore through duplicating sensors and controllers with the proposed fault tolerant scheme, both a reliability of a steam generator control and sensor system and that of a power plant increase even more. 2 refs., 9 figs., 1 tab. (Author)

  12. Measurement of reactive species generated by dielectric barrier discharge in direct contact with water in different atmospheres

    Science.gov (United States)

    Kovačević, Vesna V.; Dojčinović, Biljana P.; Jović, Milica; Roglić, Goran M.; Obradović, Bratislav M.; Kuraica, Milorad M.

    2017-04-01

    The formation of hydroxyl radical and long-living chemical species (H2O2, O3, \\text{NO}3- and \\text{NO}2- ) generated in the liquid phase of a water falling film dielectric barrier discharge in dependence on the gas atmosphere (air, nitrogen, oxygen, argon and helium) was studied. The chemical molecular probe dimethyl sulfoxide was employed for quantification of ˙OH, and the influence of hydroxyl radical scavenging on formation of reactive oxygen and nitrogen species was investigated. In addition to liquid analysis, plasma diagnostics was applied to indicate possible reaction pathways of plasma–liquid interaction. The highest ˙OH production rate of 1.19  ×  10‑5 mol l‑1 s‑1 was found when water was treated in oxygen, with a yield of 2.75  ×  10‑2 molecules of ˙OH per 100 eV. Formation of hydrogen peroxide in air, nitrogen and argon discharges is determined by recombination reaction of hydroxyl radicals, reaching the highest yield of about 0.7 g kWh‑1 when distilled water was treated in argon discharge. Ozone formation was dominant in oxygen and air discharges. Strong acidification along with formation of reactive nitrogen species was detected in water treated in air and nitrogen discharges.

  13. Non-thermal atmospheric pressure HF plasma source: generation of nitric oxide and ozone for bio-medical applications

    Science.gov (United States)

    Kühn, S.; Bibinov, N.; Gesche, R.; Awakowicz, P.

    2010-01-01

    A new miniature high-frequency (HF) plasma source intended for bio-medical applications is studied using nitrogen/oxygen mixture at atmospheric pressure. This plasma source can be used as an element of a plasma source array for applications in dermatology and surgery. Nitric oxide and ozone which are produced in this plasma source are well-known agents for proliferation of the cells, inhalation therapy for newborn infants, disinfection of wounds and blood ozonation. Using optical emission spectroscopy, microphotography and numerical simulation, the gas temperature in the active plasma region and plasma parameters (electron density and electron distribution function) are determined for varied nitrogen/oxygen flows. The influence of the gas flows on the plasma conditions is studied. Ozone and nitric oxide concentrations in the effluent of the plasma source are measured using absorption spectroscopy and electro-chemical NO-detector at variable gas flows. Correlations between plasma parameters and concentrations of the particles in the effluent of the plasma source are discussed. By varying the gas flows, the HF plasma source can be optimized for nitric oxide or ozone production. Maximum concentrations of 2750 ppm and 400 ppm of NO and O3, correspondingly, are generated.

  14. Diagnosis of Methane Plasma Generated in an Atmospheric Pressure DBD Micro-Jet by Optical Emission Spectroscopy

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jun-Feng; BIAN Xin-Chao; CHEN Qiang; LIU Fu-Ping; LIU Zhong-Wei

    2009-01-01

    Diagnosis of methane plasma,generated in an atmospheric pressure dielectric barrier discharge (DBD) microplasma jet with a quartz tube as dielectric material by a 25 kHz sinusoidal ac power source,is conducted by optical emission spectroscopy (OES).The reactive radicals in methane plasma such as CH,C2,and Ha are detected insitu by OES.The possible dissociation mechanism of methane in diluted Ar plasma is deduced from spectra.In addition,the density of CH radical,which is considered as one of the precursors in diamond-like (DLC) film formation,affected by the parameters of input voltage and the feed gas flow rate,is emphasized. With the Boltzmann plots,four Ar atomic spectral lines (located at 675.28nm,687.13nm,738.40nm and 794.82nm,respectively) are chosen to calculate the electron temperature,and the dependence of electron temperature on discharge parameters is also investigated.

  15. Control for Wind Power Generation Based on Inverse System Theory

    Directory of Open Access Journals (Sweden)

    Jiyong Zhang

    2013-11-01

    Full Text Available Traditional Double-fed Wind Generation systems are based on the vector control method, and it is dependent on motor parameters. The performance of the control system will be affected with the parameters changing,. This paper proposes a new control method based on inverse system and variable structure sliding mode(VSS theories, through the inverse system theory, the structure of its state’s equation, obtaining the structure of the inverse system, the establishment of Wind Power Generation closed-loop control system is established. The VSS controller, designed with exponential reaching law, can improve the dynamic performance in normal operation range effectively. When the system operates with variable speed constant frequency (VSCF and the phase voltage drops, the simulations show that the control system can control the DC link voltage steabily, maintain unity power factor, achieve the decoupling of the active and reactive power. And experiments show that the control method used in  VSCF wind power system is feasible.  

  16. Cold Atmospheric Plasma Manipulation of Proteins in Food Systems

    DEFF Research Database (Denmark)

    Tolouie, Haniye; Hashemi, Maryam; Mohammadifar, Mohammad Amin

    2017-01-01

    Plasma processing has been getting a lot of attention in recent applications as a novel, eco-friendly, and highly efficient approach. Cold plasma has mostly been used to reduce microbial counts in foodstuff and biological materials, as well as in different levels of packaging, particularly in cases...... where there is thermal sensitivity. As it is a very recent application, the impact of cold plasma treatment has been studied on the protein structures of food and pharmaceutical systems, as well as in the packaging industry. Proteins, as a food constituent, play a remarkable role in the techno...... of plasma on the conformation and function of proteins with food origin, especially enzymes and allergens, as well as protein-made packaging films. In enzyme manipulation with plasma, deactivation has been reported to be either partial or complete. In addition, an activity increase has been observed in some...

  17. A Coupled Atmospheric and Wave Modeling System for Storm Simulations

    DEFF Research Database (Denmark)

    Du, Jianting; Larsén, Xiaoli Guo; Bolanos, R.

    2015-01-01

    to parametrize z0. The results are validated through QuikScat data and point measurements from an open ocean site Ekosk and a coastal, relatively shallow water site Horns Rev. It is found that the modeling system captures in general better strong wind and strong wave characteristics for open ocean condition than...... Research and Forecasting (WRF) Model with the thirdgeneration ocean wave modelSWAN. This study investigates mainly two issues: spatial resolution and the wind-wave interface parameter roughness length(z0). To study the impact of resolution, the nesting function for both WRF and SWAN is used, with spatial...... (1991) z0 expression gives better results of the signicant wave hight under high sea state conditions....

  18. Development of Laser, Detector, and Receiver Systems for an Atmospheric CO2 Lidar Profiling System

    Science.gov (United States)

    Ismail, Syed; Koch, Grady; Abedin, Nurul; Refaat, Tamer; Rubio, Manuel; Singh, Upendra

    2008-01-01

    A ground-based Differential Absorption Lidar (DIAL) is being developed with the capability to measure range-resolved and column amounts of atmospheric CO2. This system is also capable of providing high-resolution aerosol profiles and cloud distributions. It is being developed as part of the NASA Earth Science Technology Office s Instrument Incubator Program. This three year program involves the design, development, evaluation, and fielding of a ground-based CO2 profiling system. At the end of a three-year development this instrument is expected to be capable of making measurements in the lower troposphere and boundary layer where the sources and sinks of CO2 are located. It will be a valuable tool in the validation of NASA Orbiting Carbon Observatory (OCO) measurements of column CO2 and suitable for deployment in the North American Carbon Program (NACP) regional intensive field campaigns. The system can also be used as a test-bed for the evaluation of lidar technologies for space-application. This DIAL system leverages 2-micron laser technology developed under a number of NASA programs to develop new solid-state laser technology that provides high pulse energy, tunable, wavelength-stabilized, and double-pulsed lasers that are operable over pre-selected temperature insensitive strong CO2 absorption lines suitable for profiling of lower tropospheric CO2. It also incorporates new high quantum efficiency, high gain, and relatively low noise phototransistors, and a new receiver/signal processor system to achieve high precision DIAL measurements.

  19. Deciphering the Hot Giant Atmospheres Orbiting Nearby Extrasolar Systems with JWST

    Science.gov (United States)

    Afrin Badhan, Mahmuda; Batalha, Natasha; Deming, Drake; Domagal-Goldman, Shawn; HEBRARD, Eric; Kopparapu, Ravi Kumar; Irwin, Patrick Gerard Joseph

    2016-10-01

    Unique and exotic planets give us an opportunity to understand how planetary systems form and evolve over their lifetime, by placing our own planetary system in the context of the vastly different extrasolar systems that are being continually discovered by present space missions. With orbital separations that are less than one-tenth of the Mercury-Sun distance, these close-in planets provide us with valuable insights about the host stellar atmosphere and planetary atmospheres subjected to their enormous stellar insolation. Observed spectroscopic signatures reveal all spectrally active species in a planet, along with information about its thermal structure and dynamics, allowing us to characterize the planet's atmosphere. NASA's upcoming missions will give us the high-resolution spectra necessary to constrain the atmospheric properties with unprecedented accuracy. However, to interpret the observed signals from exoplanetary transit events with any certainty, we need reliable atmospheric retrieval tools that can model the expected observables adequately. In my work thus far, I have built a Markov Chain Monte Carlo (MCMC) convergence scheme, with an analytical radiative equilibrium formulation for the thermal structures, within the NEMESIS atmospheric modeling tool, to allow sufficient (and efficient) exploration of the parameter space. I also augmented the opacity tables to improve the speed and reliability of retrieval models. I then utilized this upgraded version to infer the pressure-temperature (P-T) structures and volume-mixing ratios (VMRs) of major gas species in hot Jupiter dayside atmospheres, from their emission spectra. I have employed a parameterized thermal structure to retrieve plausible P-T profiles, along with altitude-invariant VMRs. Here I show my retrieval results on published datasets of HD189733b, and compare them with both medium and high spectral resolution JWST/NIRSPEC simulations. In preparation for the upcoming JWST mission, my current work

  20. An analytical system enabling consistent and long-term measurement of atmospheric dimethyl sulfide

    Science.gov (United States)

    Jang, Sehyun; Park, Ki-Tae; Lee, Kitack; Suh, Young-Sang

    2016-06-01

    We describe here an analytical system capable of continuous measurement of atmospheric dimethylsulfide (DMS) at pptv levels. The system uses customized devices for detector calibration and for DMS trapping and desorption that are controlled using a data acquisition system (based on Visual Basic 6.0/C 6.0) designed to maximize the efficiency of DMS analysis in a highly sensitive pulsed flame photometric detector housed in a gas chromatograph. The fully integrated system, which can sample approximately 6 L of air during a 1-hr sampling, was used to measure the atmospheric DMS mixing ratio over the Atlantic sector of the Arctic Ocean over 3 full annual growth cycles of phytoplankton in 2010, 2014, and 2015, with minimal routine maintenance and interruptions. During the field campaigns, the measured atmospheric DMS mixing ratio varied over a considerable range, from <1.5 pptv to maximum levels of 298 pptv in 2010, 82 pptv in 2014, and 429 pptv in 2015. The operational period covering the 3 full annual growth cycles of phytoplankton showed that the system is suitable for uninterrupted measurement of atmospheric DMS mixing ratios in extreme environments. Moreover, the findings obtained using the system showed it to be useful in identifying ocean DMS source regions and changes in source strength.

  1. Analysis of Translating Hydrofoil Power Generation Systems (Hydrokites)

    Science.gov (United States)

    McConnaghy, Kelsey

    The hydrokite is a novel hydro-power system that is based on emerging kite wind-energy systems which are currently being designed for use at high altitudes. The hydrokite system is comprised of a hydrofoil and a support system, and is designed to capture kinetic energy from the flow of a river while reducing negative impacts on the river ecology by minimally interfering with the rivers natural flow (i.e. no dams or river diversions are needed). This work presents some initial results which demonstrate the power performance capabilities of the hydrokite. Two different steady-state models for this system were studied to determine the effects of model parameters on power generation. A dynamic model was also developed and preliminary results are presented. These simplified initial models provide an upper bound for the power performance of an actual system as well as providing an understanding of the effects that parameter changes have on the system performance. This initial work shows that such a system could be a feasible, low impact method for generating renewable energy from low-head hydro sources.

  2. Mini Solar and Sea Current Power Generation System

    Science.gov (United States)

    Almenhali, Abdulrahman; Alshamsi, Hatem; Aljunaibi, Yaser; Almussabi, Dheyab; Alshehhi, Ahmed; Hilal, Hassan Bu

    2017-07-01

    The power demand in United Arab Emirates is increased so that there is a consistent power cut in our region. This is because of high power consumption by factories and also due to less availability of conventional energy resources. Electricity is most needed facility for the human being. All the conventional energy resources are depleting day by day. So we have to shift from conventional to non-conventional energy resources. In this the combination of two energy resources is takes place i.e. wind and solar energy. This process reviles the sustainable energy resources without damaging the nature. We can give uninterrupted power by using hybrid energy system. Basically this system involves the integration of two energy system that will give continuous power. Solar panels are used for converting solar energy and wind turbines are used for converting wind energy into electricity. This electrical power can utilize for various purpose. Generation of electricity will be takes place at affordable cost. This paper deals with the generation of electricity by using two sources combine which leads to generate electricity with affordable cost without damaging the nature balance. The purpose of this project was to design a portable and low cost power system that combines both sea current electric turbine and solar electric technologies. This system will be designed in efforts to develop a power solution for remote locations or use it as another source of green power.

  3. Fuzzy logic based variable speed wind generation system

    Energy Technology Data Exchange (ETDEWEB)

    Simoes, M.G. [Sao Paulo Univ., SP (Brazil). Escola Politecnica. PMC - Mecatronica; Bose, B.K. [Tennessee Univ., Knoxville, TN (United States). Dept. of Electrical Engineering; Spiegel, Ronal J. [Environmental Protection Agency, Research Triangle Park, NC (United States). Air and Energy Engineering Research Lab.

    1996-12-31

    This work demonstrates the successful application of fuzzy logic to enhance the performance and control of a variable speed wind generation system. A maximum power point tracker control is performed with three fuzzy controllers, without wind velocity measurement, and robust to wind vortex and turbine torque ripple. A squirrel cage induction generator feeds the power to a double-sided PWM converter system which pumps the power to a utility grid or supplies to an autonomous system. The fuzzy logic controller FLC-1 searches on-line the generator speed so that the aerodynamic efficiency of the wind turbine is optimized. A second fuzzy controller FLC-2 programs the machine flux by on-line search so as to optimize the machine-converter system wind vortex. Detailed analysis and simulation studies were performed for development of the control strategy and fuzzy algorithms, and a DSP TMS320C30 based hardware with C control software was built for the performance evaluation of a laboratory experimental set-up. The theoretical development was fully validated and the system is ready to be reproduced in a higher power installation. (author) 7 refs., 3 figs., 1 tab.

  4. Solar Stirling power generation - Systems analysis and preliminary tests

    Science.gov (United States)

    Selcuk, M. K.; Wu, Y.-C.; Moynihan, P. I.; Day, F. D., III

    1977-01-01

    The feasibility of an electric power generation system utilizing a sun-tracking parabolic concentrator and a Stirling engine/linear alternator is being evaluated. Performance predictions and cost analysis of a proposed large distributed system are discussed. Design details and preliminary test results are presented for a 9.5 ft diameter parabolic dish at the Jet Propulsion Laboratory (Caltech) Table Mountain Test Facility. Low temperature calorimetric measurements were conducted to evaluate the concentrator performance, and a helium flow system is being used to test the solar receiver at anticipated working fluid temperatures (up to 650 or 1200 C) to evaluate the receiver thermal performance. The receiver body is designed to adapt to a free-piston Stirling engine which powers a linear alternator assembly for direct electric power generation. During the next phase of the program, experiments with an engine and receiver integrated into the concentrator assembly are planned.

  5. Development of a Cost Effective Power Generation System: An Overview

    Directory of Open Access Journals (Sweden)

    Shiv Prakash Bihari

    2016-03-01

    Full Text Available This paper presents an overview on development of cost effective power generation system and motivates for development of a model for hybrid system with wind to investigate the combined operation of wind with different sources to cater to wind’s stochastic nature for imbalance minimization and optimal operation. Development of model for trading power in competitive electricity market and development of strategies for trading in electricity markets (wind energy and reserves markets to investigate the effects of real time pricing tariffs on electricity market operation has been illustrated in this paper. Dynamic modelling related studies to investigate the wind generator’s kinetic energy for primary frequency support using simulink and simulation studies on doubly fed induction generator to study its capability during small disturbances / fluctuations on power system have been described.

  6. Adaptive Dynamic Surface Control for Generator Excitation Control System

    Directory of Open Access Journals (Sweden)

    Zhang Xiu-yu

    2014-01-01

    Full Text Available For the generator excitation control system which is equipped with static var compensator (SVC and unknown parameters, a novel adaptive dynamic surface control scheme is proposed based on neural network and tracking error transformed function with the following features: (1 the transformation of the excitation generator model to the linear systems is omitted; (2 the prespecified performance of the tracking error can be guaranteed by combining with the tracking error transformed function; (3 the computational burden is greatly reduced by estimating the norm of the weighted vector of neural network instead of the weighted vector itself; therefore, it is more suitable for the real time control; and (4 the explosion of complicity problem inherent in the backstepping control can be eliminated. It is proved that the new scheme can make the system semiglobally uniformly ultimately bounded. Simulation results show the effectiveness of this control scheme.

  7. Z - Source Multi Level Inverter Based PV Generation System

    Directory of Open Access Journals (Sweden)

    T. Lakhmi kanth

    2014-09-01

    Full Text Available In this paper a novel technique of Z-Source multilevel Inverter based PV Generation system is implemented and simulated using MATLAB-Simulink simulation software. The Photovoltaic cells are healthier option for converting solar energy into electricity. Due to high capital cost and low efficiency PV cells have not yet been a fully smart choice for electricity users. To enhance the performance of the system, Z-Source multi level inverter can be used in place of conventional Voltage Source Inverter (VSI in Solar Power Generation System. The PV cell model is developed using circuit mathematical equations. The Z-Source multilevel inverter is modeled to realize boosted DC to AC conversion (inversion with low THD. Outcome shows that the energy conversion efficiency of ZSMLI is a lot improved as compared to conventional voltage Source Inverter (VSI. By doing FFT analysis we can know the total THD.

  8. Using Unmanned Air Systems to Monitor Methane in the Atmosphere

    Science.gov (United States)

    Clow, Jacqueline; Smith, Jeremy Christopher

    2016-01-01

    Methane is likely to be an important contributor to global warming, and our current knowledge of its sources, distributions, and transport is insufficient. It is estimated that there could be from 7.5 to 400 billion tons carbon-equivalent of methane in the arctic region, a broad range that is indicative of the uncertainty within the Earth Science community. Unmanned Air Systems (UASs) are often used for combat or surveillance by the military, but they also have been used for Earth Science field missions. In this study, we will analyze the utility of the NASA Global Hawk and the Aurora Flight Sciences Orion UASs compared to the manned DC-8 aircraft for conducting a methane monitoring mission. The mission will focus on the measurement of methane along the boundaries of Arctic permafrost thaw and melting glaciers. The use of Long Endurance UAS brings a new range of possibilities including the ability to obtain long- term and persistent observations and to significantly augment methane measurements/retrievals collected by satellite. Furthermore, we discuss the future of long endurance UAS and their potential for science applications in the next twenty to twenty-five years.

  9. BER of subcarrier MPSK and MDPSK systems in atmospheric turbulence

    KAUST Repository

    Song, Xuegui

    2015-01-01

    Bit-error rate (BER) performance of subcarrier $M$-ary phase-shift keying (MPSK) and $M$-ary differential PSK (MDPSK) is analyzed for optical wireless communications over Gamma-Gamma and lognormal turbulence channels. We study the relation between the exact BER and the approximate BER, which is obtained by dividing the symbol-error rate by the number of bits per symbol, for subcarrier MPSK and MDPSK modulations. The asymptotic BER performance gap between the exact and the approximate BERs is quantified analytically through our asymptotic analyses. The accuracy of the approximate BER of both MPSK and MDPSK depends on the channel conditions. Under weak turbulence conditions, the approximate BER expression can be used to predict the system performance with high accuracy, while under strong turbulence conditions the approximate BER becomes inaccurate and can only serve as a loose lower bound of the exact BER. The asymptotic BER performance loss of MDPSK with respect to MPSK is also quantified analytically.

  10. Atmospheric Pressure Low Temperature Plasma System for Additive Manufacturing

    Science.gov (United States)

    Burnette, Matthew; Staack, David

    2016-09-01

    There is growing interest in using plasmas for additive manufacturing, however these methods use high temperature plasmas to melt the material. We have developed a novel technique of additive manufacturing using a low temperature dielectric barrier discharge (DBD) jet. The jet is attached to the head of a 3D printer to allow for precise control of the plasma's location. Various methods are employed to deposit the material, including using a vaporized precursor or depositing a liquid precursor directly onto the substrate or into the plasma via a nebulizer. Various materials can be deposited including metals (copper using copper (II) acetylacetonate), polymers (PMMA using the liquid monomer), and various hydrocarbon compounds (using alcohols or a 100% methane DBD jet). The rastering pattern for the 3D printer was modified for plasma deposition, since it was originally designed for thermoplastic extrusion. The design constraints for fill pattern selection for the plasma printer are influenced by substrate heating, deposition area, and precursor consumption. Depositions onto pressure and/or temperature sensitive substrates can be easily achieved. Deposition rates range up to 0.08 cm3/hr using tris(2-methoxyethoxy)(vinyl)silane, however optimization can still be done on the system to improve the deposition rate. For example higher concentration of precursor can be combined with faster motion and higher discharge powers to increase the deposition rate without overheating the substrate.

  11. Wind Generation Participation in Power System Frequency Response: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Gevorgian, Vahan; Zhang, Yingchen

    2017-01-01

    The electrical frequency of an interconnected power system must be maintained close its nominal level at all times. Excessive under- and overfrequency excursions can lead to load shedding, instability, machine damage, and even blackouts. There is a rising concern in the electric power industry in recent years about the declining amount of inertia and primary frequency response (PFR) in many interconnections. This decline may continue due to increasing penetrations of inverter-coupled generation and the planned retirements of conventional thermal plants. Inverter-coupled variable wind generation is capable of contributing to PFR and inertia with a response that is different from that of conventional generation. It is not yet entirely understood how such a response will affect the system at different wind power penetration levels. The modeling work presented in this paper evaluates the impact of wind generation's provision of these active power control strategies on a large, synchronous interconnection. All simulations were conducted on the U.S. Western Interconnection with different levels of instantaneous wind power penetrations (up to 80%). The ability of wind power plants to provide PFR - and a combination of synthetic inertial response and PFR - significantly improved the frequency response performance of the system.

  12. Apparatus, System, and Method for On-Chip Thermoelectricity Generation

    KAUST Repository

    Hussain, Muhammad Mustafa

    2012-01-26

    An apparatus, system, and method for a thermoelectric generator. In some embodiments, the thermoelectric generator comprises a first thermoelectric region and a second thermoelectric region, where the second thermoelectric region may be coupled to the first thermoelectric region by a first conductor. In some embodiments, a second conductor may be coupled to the first thermoelectric region and a third conductor may be coupled to the second thermoelectric region. In some embodiments, the first conductor may be in a first plane, the first thermoelectric region and the second thermoelectric region may be in a second plane, and the second conductor and the third conductor may be in a third plane.

  13. Electric power systems advanced forecasting techniques and optimal generation scheduling

    CERN Document Server

    Catalão, João P S

    2012-01-01

    Overview of Electric Power Generation SystemsCláudio MonteiroUncertainty and Risk in Generation SchedulingRabih A. JabrShort-Term Load ForecastingAlexandre P. Alves da Silva and Vitor H. FerreiraShort-Term Electricity Price ForecastingNima AmjadyShort-Term Wind Power ForecastingGregor Giebel and Michael DenhardPrice-Based Scheduling for GencosGovinda B. Shrestha and Songbo QiaoOptimal Self-Schedule of a Hydro Producer under UncertaintyF. Javier Díaz and Javie

  14. Declarative Business Process Modelling and the Generation of ERP Systems

    Science.gov (United States)

    Schultz-Møller, Nicholas Poul; Hølmer, Christian; Hansen, Michael R.

    We present an approach to the construction of Enterprise Resource Planning (ERP) Systems, which is based on the Resources, Events and Agents (REA) ontology. This framework deals with processes involving exchange and flow of resources in a declarative, graphically-based manner describing what the major entities are rather than how they engage in computations. We show how to develop a domain-specific language on the basis of REA, and a tool which automatically can generate running web-applications. A main contribution is a proof-of-concept showing that business-domain experts can generate their own applications without worrying about implementation details.

  15. Molecular system generation with strong resonance optical pumping

    Energy Technology Data Exchange (ETDEWEB)

    Kuntsevich, B.F.; Churakov, V.V.

    1977-03-01

    A study was made of molecular system generation modulated by three oscillating levels with a rotating structure with strong resonance optical pumping. Molecular behavior of the active medium is described by equations for the density matrix. The relationship between the amplification coefficient and pressure at various pumping intensities was examined. In approaching the assigned pumping field, an examination was made of how the generation field is affected by the volumetric density of the pumping energy, partial pressure of the buffer gas and frequency difference in the pumping channel.

  16. A hybrid surface layer parameterization scheme for the two-way fully coupled atmosphere-ocean wave system WEW

    Science.gov (United States)

    Katsafados, Petros; Papadopoulos, Anastasios; Varlas, George; Korres, Gerasimos

    2015-04-01

    The two-way fully coupled atmosphere-ocean wave system WEW has been recently developed in order to study the factors that contribute to the air-sea interaction processes and feedbacks. The coupled system consists of two components: the atmospheric component which is based on the Workstation Eta non-hydrostatic limited area model and the ocean-wave component which is based on the fourth generation OpenMP (OMP) version of the WAM model. The WEW has been already evaluated in a number of high-impact weather and sea state events where generally a more realistic representation of the momentum exchanges in the ocean wind-wave system has been shown However, the new developed wind-wave parameterization scheme reduces both the near surface wind speed and the significant wave height as a response to the increased aerodynamic drag considered by the atmospheric model over rough sea surfaces. Such behavior is mainly attributed to the surface layer parameterization scheme of the atmospheric component which is based on the Mellor-Yamada-Janjic (MYJ) scheme. It is noted that this scheme has been adjusted to support independent atmospheric simulations. Therefore, we proceed to develop a new hybrid surface layer parameterization based on the MYJ and the Janssen schemes that operate in the atmospheric and ocean wave components of the WEW, respectively. In this case the roughness length depends on the wave age instead of the Charnock parameter following the formulation proposed by Vickers and Mahrt. The spatial variability of the wave age is estimated at each ocean wave component time step and it is directly provided to the MYJ scheme. The parameterization of the viscous sublayer and the universal functions for the estimation of the near surface wind speed have been also revised accordingly. In this study, a test version of the new hybrid scheme of WEW has been statistically evaluated against a number of buoys and satellite retrievals over the Mediterranean Sea in a case study of high

  17. Energy system analysis of fuel cells and distributed generation

    DEFF Research Database (Denmark)

    Mathiesen, Brian Vad; Lund, Henrik

    2007-01-01

    on the energy system in which they are used. Consequently, coherent energy systems analyses of specific and complete energy systems must be conducted in order to evaluate the benefits of FC technologies and in order to be able to compare alternative solutions. In relation to distributed generation, FC...... can be used for such analyses. Moreover, the chapter presents the results of evaluating the overall system fuel savings achieved by introducing different FC applications into different energy systems. Natural gas-based and hydrogen-based micro FC-CHP, natural gas local FC-CHP plants for district...... technologies have different strengths and weaknesses in different energy systems, but often they do not have the expected effect. Specific analyses of each individual country must be conducted including scenarios of expansion of e.g. wind power in order to evaluate where and when the best use of FC...

  18. Loss Allocation in a Distribution System with Distributed Generation Units

    DEFF Research Database (Denmark)

    Lund, Torsten; Nielsen, Arne Hejde; Sørensen, Poul Ejnar

    2007-01-01

    In Denmark, a large part of the electricity is produced by wind turbines and combined heat and power plants (CHPs). Most of them are connected to the network through distribution systems. This paper presents a new algorithm for allocation of the losses in a distribution system with distributed...... generation. The algorithm is based on a reduced impedance matrix of the network and current injections from loads and production units. With the algorithm, the effect of the covariance between production and consumption can be evaluated. To verify the theoretical results, a model of the distribution system...

  19. Civil aircraft for the regular investigation of the atmosphere based on an instrumented container: the new CARIBIC system

    OpenAIRE

    Brenninkmeijer, C. A. M.; Crutzen, P.; Boumard, F.; Dauer, T.; B. Dix; Ebinghaus, R.; Filippi, D.; Fischer, H.; Franke, H.; U. Frieβ; Heintzenberg, J; F. Helleis; Hermann, M; H. H. Kock; Koeppel, C.

    2007-01-01

    An airfreight container with automated instruments for measurement of atmospheric gases and trace compounds was operated on a monthly basis onboard a Boeing 767-300 ER of LTU International Airways during long-distance flights from 1997 to 2002 (CARIBIC, Civil Aircraft for Regular Investigation of the Atmosphere Based on an Instrument Container, atmospheric.com">http://www.caribic-atmospheric.com). Subsequently a more advanced system has be...

  20. Statistical predictability in the atmosphere and other dynamical systems

    Science.gov (United States)

    Kleeman, Richard

    2007-06-01

    Ensemble predictions are an integral part of routine weather and climate prediction because of the sensitivity of such projections to the specification of the initial state. In many discussions it is tacitly assumed that ensembles are equivalent to probability distribution functions (p.d.f.s) of the random variables of interest. In general for vector valued random variables this is not the case (not even approximately) since practical ensembles do not adequately sample the high dimensional state spaces of dynamical systems of practical relevance. In this contribution we place these ideas on a rigorous footing using concepts derived from Bayesian analysis and information theory. In particular we show that ensembles must imply a coarse graining of state space and that this coarse graining implies loss of information relative to the converged p.d.f. To cope with the needed coarse graining in the context of practical applications, we introduce a hierarchy of entropic functionals. These measure the information content of multivariate marginal distributions of increasing order. For fully converged distributions (i.e. p.d.f.s) these functionals form a strictly ordered hierarchy. As one proceeds up the hierarchy with ensembles instead however, increasingly coarser partitions are required by the functionals which implies that the strict ordering of the p.d.f. based functionals breaks down. This breakdown is symptomatic of the necessarily limited sampling by practical ensembles of high dimensional state spaces and is unavoidable for most practical applications. In the second part of the paper the theoretical machinery developed above is applied to the practical problem of mid-latitude weather prediction. We show that the functionals derived in the first part all decline essentially linearly with time and there appears in fact to be a fairly well defined cut off time (roughly 45 days for the model analyzed) beyond which initial condition information is unimportant to

  1. SITE GENERATED RADIOLOGICAL WASTE HANDLING SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    S. C. Khamankar

    2000-06-20

    The Site Generated Radiological Waste Handling System handles radioactive waste products that are generated at the geologic repository operations area. The waste is collected, treated if required, packaged for shipment, and shipped to a disposal site. Waste streams include low-level waste (LLW) in solid and liquid forms, as-well-as mixed waste that contains hazardous and radioactive constituents. Liquid LLW is segregated into two streams, non-recyclable and recyclable. The non-recyclable stream may contain detergents or other non-hazardous cleaning agents and is packaged for shipment. The recyclable stream is treated to recycle a large portion of the water while the remaining concentrated waste is packaged for shipment; this greatly reduces the volume of waste requiring disposal. There will be no liquid LLW discharge. Solid LLW consists of wet solids such as ion exchange resins and filter cartridges, as-well-as dry active waste such as tools, protective clothing, and poly bags. Solids will be sorted, volume reduced, and packaged for shipment. The generation of mixed waste at the Monitored Geologic Repository (MGR) is not planned; however, if it does come into existence, it will be collected and packaged for disposal at its point of occurrence, temporarily staged, then shipped to government-approved off-site facilities for disposal. The Site Generated Radiological Waste Handling System has equipment located in both the Waste Treatment Building (WTB) and in the Waste Handling Building (WHB). All types of liquid and solid LLW are processed in the WTB, while wet solid waste from the Pool Water Treatment and Cooling System is packaged where received in the WHB. There is no installed hardware for mixed waste. The Site Generated Radiological Waste Handling System receives waste from locations where water is used for decontamination functions. In most cases the water is piped back to the WTB for processing. The WTB and WHB provide staging areas for storing and shipping LLW

  2. A Biomedical Assessment of a One-Atmosphere Diving System: JIM-4.

    Science.gov (United States)

    1981-12-01

    diving dress ................................. A7 Fig. 9. Galeazzi diving suit ................................. A8 Fig. 10. Peress’s diving system, the...joints, one in each shoulder and two in each leg. Around the time that Neufeldt and Kuhnke were developing their system, an Italian developer Galeazzi ...produced an atmospheric diving system (Davis, 1969). A photograph in Davis’s book shows a 1930’s Galeazzi suit that is virtually identical to a recent

  3. Development of an Accurate Urban Modeling System Using CAD/GIS Data for Atmosphere Environmental Simulation

    Institute of Scientific and Technical Information of China (English)

    Tomosato Takada; Kazuo Kashiyama

    2008-01-01

    This paper presents an urban modeling system using CAD/GIS data for atmosphere environ- mental simulation, such as wind flow and contaminant spread in urban area. The CAD data is used for the shape modeling for the high-storied buildings and civil structures with complicated shape since the data for that is not included in the 3D-GIS data accurately. The unstructured mesh based on the tetrahedron element is employed in order to express the urban structures with complicated shape accurately. It is difficult to un- derstand the quality of shape model and mesh by the conventional visualization technique. In this paper, the stereoscopic visualization using virtual reality (VR) technology is employed for the vedfication of the quality of shape model and mesh. The present system is applied to the atmosphere environmental simulation in ur- ban area and is shown to be an useful planning and design tool to investigate the atmosphere environmental problem.

  4. 3D measurement system based on computer-generated gratings

    Science.gov (United States)

    Zhu, Yongjian; Pan, Weiqing; Luo, Yanliang

    2010-08-01

    A new kind of 3D measurement system has been developed to achieve the 3D profile of complex object. The principle of measurement system is based on the triangular measurement of digital fringe projection, and the fringes are fully generated from computer. Thus the computer-generated four fringes form the data source of phase-shifting 3D profilometry. The hardware of system includes the computer, video camera, projector, image grabber, and VGA board with two ports (one port links to the screen, another to the projector). The software of system consists of grating projection module, image grabbing module, phase reconstructing module and 3D display module. A software-based synchronizing method between grating projection and image capture is proposed. As for the nonlinear error of captured fringes, a compensating method is introduced based on the pixel-to-pixel gray correction. At the same time, a least square phase unwrapping is used to solve the problem of phase reconstruction by using the combination of Log Modulation Amplitude and Phase Derivative Variance (LMAPDV) as weight. The system adopts an algorithm from Matlab Tool Box for camera calibration. The 3D measurement system has an accuracy of 0.05mm. The execution time of system is 3~5s for one-time measurement.

  5. Stochastic Modeling and Analysis of Power System with Renewable Generation

    DEFF Research Database (Denmark)

    Chen, Peiyuan

    to evaluate year-to-year variation of wind power generation through a sensitivity analysis and to forecast very short-term wind power through a model-based prediction method. The stochastic load model is established on the basis of a seasonal autoregressive moving average (ARMA) process. It is demonstrated...... that such a stochastic model can be used to simulate the effect of load management on the load duration curve. As CHP units are turned on and off by regulating power, CHP generation has discrete output and thus can be modeled by a transition matrix based discrete Markov chain. As the CHP generation has a strong diurnal...... that minimizes the expectation of power losses of a 69-bus distribution system by controlling the power factor of WTs. The optimization is subjected to the probabilistic constraints of bus voltage and line current. The algorithm combines a constrained nonlinear optimization algorithm and a Monte Carlo based PLF...

  6. Power Electronics for the Next Generation Wind Turbine System

    DEFF Research Database (Denmark)

    Ma, Ke

    generation unit, are becoming crucial in the wind turbine system. The objective of this project is to study the power electronics technology used for the next generation wind turbines. Some emerging challenges as well as potentials like the cost of energy and reliability are going to be addressed. First......The wind power generation has been steadily growing both for the total installed capacity and for the individual turbine size. Due to much more significant impacts to the power grid, the power electronics, which can change the behavior of wind turbines from an unregulated power source to an active...... semiconductors is emphasized and a multidisciplinary approach for the stress analysis is introduced. Based on the proposed criteria and tools, the electrical and thermal behaviors of wind power converters are investigated under both normal and fault conditions, where the factors of wind speeds, grid codes...

  7. Synchronous pulse generation in a multicavity fiber laser system

    Science.gov (United States)

    Gómez-Pavón, L. C.; Martí-Panameño, E.; Gómez-de la Fuente, O.; Luis-Ramos, A.

    2006-09-01

    We report the experimental synchronous pulse generation in a multicavity fiber laser system with two Erbium-doped fiber laser cavities. We have demonstrated that through the evanescent fields interaction between one cavity with active modulation and other one in continuous wave it is possible to generate more intense pulses in both cavities. Moreover, the synchronous pulse generation between cavities is achieved with an appropriate selection of pump intensity, modulation frequency and coupling ratio. We found that the pulse intensity is 2.5 times greater and the pulse duration lowers than a single Erbium-doper fiber laser. Furthermore, by means of the synchronous diagram we determined the synchronization strength in temporal pulse emission between cavities.

  8. Beamlet pulse-generation and wavefront-control system

    Energy Technology Data Exchange (ETDEWEB)

    Van Wonterghem, B.M.; Salmon, J.T.; Wilcox, R.W.

    1996-06-01

    The Beamlet pulse-generation system (or {open_quotes}front end{close_quotes}) refers to the laser hardware that generates the spatially and temporally shaped pulse that is injected into the main laser cavity. All large ICF lasers have pulse-generation systems that typically consist of a narrow-band oscillator, elector-optic modulators for temporal and bandwidth shaping, and one or more preamplifiers. Temporal shaping is used to provide the desired laser output pulse shape and also to compensate for gain saturation effects in the large-aperture amplifiers. Bandwidth is applied to fulfill specific target irradiation requirements and to avoid stimulated Brillouin scattering (SBS) in large-aperture laser components. Usually the sharp edge of the beam`s spatial intensity profile is apodized before injection in the main amplifier beam line. This prevents large-amplitude ripples on the intensity profile. Here the authors briefly review the front-end design and discuss improvements to the oscillator and modulator systems. Their main focus, however, is to describe Beamlet`s novel beam-shaping and wavefront-control systems that have recently been fully activated and tested.

  9. Performance optimization for doubly fed wind power generation systems

    Energy Technology Data Exchange (ETDEWEB)

    Bhowmik, S.; Spee, R.; Enslin, J.H.R.

    1999-08-01

    Significant variation of the resource kinetic energy, in the form of wind speed, results in substantially reduced energy capture in a fixed-speed wind turbine. In order to increase the wind energy capture in the turbine, variable-speed generation (VSG) strategies have been proposed and implemented. However, that requires an expensive ac/ac power converter, which increases the capital investment significantly. Consequently, doubly fed systems have been proposed to reduce the size of the power converter and, thereby, the associated cost. Additionally, in doubly fed systems, as a fixed operating point (power and speed), power flow can be regulated between the two winding systems on the machine. This feature can by utilized to essentially minimize losses in the machine associated with the given operating point or achieve other desired performance enhancements. In this paper, a brushless doubly fed machine (BDFM) is utilized to develop a VSG wind power generator. The VSG controller employs a wind-speed-estimation-based maximum power point tracker and a heuristic-model-based maximum efficiency point tracker to optimize the power output of the system. The controller has been verified for efficacy on a 1.5-kW laboratory VSG wind generator. The strategy is applicable to all doubly fed configurations, including conventional wound-rotor induction machines, Scherbius cascades, BDFM's and doubly fed reluctance machines.

  10. Designing a 3rd generation, authenticatable attribute measurement system

    Energy Technology Data Exchange (ETDEWEB)

    Thron, Jonathan [Los Alamos National Laboratory; Karpius, Peter [Los Alamos National Laboratory; Santi, Peter [Los Alamos National Laboratory; Smith, Morag [Los Alamos National Laboratory; Vo, Duc [Los Alamos National Laboratory; Williams, Richard [Los Alamos National Laboratory

    2009-01-01

    Attribute measurement systems (AMS) are designed to measure potentially sensitive items containing Special Nuclear Materials to determine if the items possess attributes which fall within an agreed-upon range. Such systems could be used in a treaty to inspect and verify the identity of items in storage without revealing any sensitive information associated with the item. An AMS needs to satisfy two constraints: the host party needs to be sure that none of their sensitive information is released, while the inspecting party wants to have confidence that the limited amount of information they see accurately reflects the properties of the item being measured. The former involves 'certifying' the system and the latter 'authenticating' it. Previous work into designing and building AMS systems have focused more on the questions of certifiability than on the questions of authentication - although a few approaches have been investigated. The next step is to build a 3rd generation AMS which (1) makes the appropriate measurements, (2) can be certified, and (3) can be authenticated (the three generations). This paper will discuss the ideas, options, and process of producing a design for a 3rd generation AMS.

  11. An improved coupling model for the lithosphere-atmosphere-ionosphere system

    Science.gov (United States)

    Kuo, C. L.; Lee, L. C.; Huba, J. D.

    2014-04-01

    In our previous model for the lithosphere-atmosphere-ionosphere coupling, the background magnetic field was assumed to be perpendicular to the horizontal plane. In the present paper, we improve the calculation of currents in the atmosphere by solving the current density J directly from the current continuity equation ∇ • J = 0. The currents in the atmosphere can be solved for any arbitrary angle of magnetic field, i.e., any magnetic latitude. In addition, a large ratio (~10) of Hall to Pedersen conductivities is used to generate a large Hall electric field. The effects of atmospheric currents and electric fields on the ionosphere with lithosphere current source located at magnetic latitudes of 7.5°, 15°, 22.5°, and 30° are obtained. For upward (downward) atmospheric currents flowing into the ionosphere, the simulation results show that the westward (eastward) electric fields dominate. At magnetic latitude of 7.5° or 15°, the upward (downward) current causes the increase (decrease) of total electron content (TEC) near the source region, while the upward (downward) current causes the decrease (increase) of TEC at magnetic latitude of 22.5°or 30°. The dynamo current density required to generate the same amount of TEC variation in the improved model is found to be smaller by a factor of 30 as compared to that obtained in our earlier paper. We also calculate the ionosphere dynamics with imposed zonal westward and eastward electric field based on SAMI3 code. It is found that the eastward (westward) electric field may trigger one (two) plasma bubble(s) in the nighttime ionosphere.

  12. Radiative transfer solutions for coupled atmosphere ocean systems using the matrix operator technique

    Science.gov (United States)

    Hollstein, André; Fischer, Jürgen

    2012-05-01

    Accurate radiative transfer models are the key tools for the understanding of radiative transfer processes in the atmosphere and ocean, and for the development of remote sensing algorithms. The widely used scalar approximation of radiative transfer can lead to errors in calculated top of atmosphere radiances. We show results with errors in the order of±8% for atmosphere ocean systems with case one waters. Variations in sea water salinity and temperature can lead to variations in the signal of similar magnitude. Therefore, we enhanced our scalar radiative transfer model MOMO, which is in use at Freie Universität Berlin, to treat these effects as accurately as possible. We describe our one-dimensional vector radiative transfer model for an atmosphere ocean system with a rough interface. We describe the matrix operator scheme and the bio-optical model for case one waters. We discuss some effects of neglecting polarization in radiative transfer calculations and effects of salinity changes for top of atmosphere radiances. Results are shown for the channels of the satellite instruments MERIS and OLCI from 412.5 nm to 900 nm.

  13. Atmospheric Mining in the Outer Solar System: Aerial Vehicle Mission and Design Issues

    Science.gov (United States)

    Palaszewski, Bryan

    2015-01-01

    Atmospheric mining in the outer solar system has been investigated as a means of fuel production for high energy propulsion and power. Fusion fuels such as Helium 3 (3He) and deuterium can be wrested from the atmospheres of Uranus and Neptune and either returned to Earth or used in-situ for energy production. Helium 3 and deuterium were the primary gases of interest with hydrogen being the primary propellant for nuclear thermal solid core and gas core rocket-based atmospheric flight. A series of analyses were undertaken to investigate resource capturing aspects of atmospheric mining in the outer solar system. This included the gas capturing rate, storage options, and different methods of direct use of the captured gases. While capturing 3He, large amounts of hydrogen and 4He are produced. With these two additional gases, the potential for fueling small and large fleets of additional exploration and exploitation vehicles exists. The mining aerospacecraft (ASC) could fly through the outer planet atmospheres, for global weather observations, localized storm or other disturbance investigations, wind speed measurements, polar observations, etc. Analyses of orbital transfer vehicles (OTVs), landers, and in-situ resource utilization (ISRU) mining factories are included. Preliminary observations are presented on near-optimal selections of moon base orbital locations, OTV power levels, and OTV and lander rendezvous points.

  14. Comparaison of 85Kr measurements with the ADMS model (Atmospheric Dispersion Modelling System) on a coastal complex site

    Science.gov (United States)

    Leroy, C.; Maro, D.; Connan, O.; Hebert, D.; Rozet, M.

    2009-04-01

    Modelling atmospheric dispersion of radioactive plumes is a major issue for nuclear safety institutes to predict and estimate the radiological consequences to the population. The French Institute for the Radiological protection and the Nuclear Safety (IRSN) uses gaussian plume models, particularly adapted in accidental situations, because of short computation times. Due to the lack of experimental data, the reliability of these models is poorly documented and misunderstood for elevated sources in the near field and more particularly, in complex areas (topography, change of roughness). In order to improve the knowledge of dispersion mechanisms in such conditions, the IRSN ran a series of experimental campaigns between 1999 and 2002 in the vicinity of the La Hague nuclear reprocessing plant (AREVA NC - France). The La Hague peninsula is very narrow and the plant is located at 2 km from the coastline, at 150 m above sea level. During the experiments, the krypton-85 (85Kr), a radionucleide, was used as a non-reactive tracer of the plumes released by the 100 m high stack. In this work, the Atmospheric Transfer Coefficients (ATC) obtained from 85Kr measurements at La Hague are compared with the computations of the "next generation" gaussian model ADMS (Atmospheric Dispersion Modelling System) performed with "complex and coastal effects" ADMS modules.

  15. Next Generation Nuclear Plant Resilient Control System Functional Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lynne M. Stevens

    2010-07-01

    Control Systems and their associated instrumentation must meet reliability, availability, maintainability, and resiliency criteria in order for high temperature gas-cooled reactors (HTGRs) to be economically competitive. Research, perhaps requiring several years, may be needed to develop control systems to support plant availability and resiliency. This report functionally analyzes the gaps between traditional and resilient control systems as applicable to HTGRs, which includes the Next Generation Nuclear Plant; defines resilient controls; assesses the current state of both traditional and resilient control systems; and documents the functional gaps existing between these two controls approaches as applicable to HTGRs. This report supports the development of an overall strategy for applying resilient controls to HTGRs by showing that control systems with adequate levels of resilience perform at higher levels, respond more quickly to disturbances, increase operational efficiency, and increase public protection.

  16. Applications of Next-generation Sequencing in Systemic Autoimmune Diseases

    Directory of Open Access Journals (Sweden)

    Yiyangzi Ma

    2015-08-01

    Full Text Available Systemic autoimmune diseases are a group of heterogeneous disorders caused by both genetic and environmental factors. Although numerous causal genes have been identified by genome-wide association studies (GWAS, these susceptibility genes are correlated to a relatively low disease risk, indicating that environmental factors also play an important role in the pathogenesis of disease. The intestinal microbiome, as the main symbiotic ecosystem between the host and host-associated microorganisms, has been demonstrated to regulate the development of the body’s immune system and is likely related to genetic mutations in systemic autoimmune diseases. Next-generation sequencing (NGS technology, with high-throughput capacity and accuracy, provides a powerful tool to discover genomic mutations, abnormal transcription and intestinal microbiome identification for autoimmune diseases. In this review, we briefly outlined the applications of NGS in systemic autoimmune diseases. This review may provide a reference for future studies in the pathogenesis of systemic autoimmune diseases.

  17. Pricing Decision Support System for Generation Companies in Electricity Market

    Institute of Scientific and Technical Information of China (English)

    FangDebin; WangXianjia

    2005-01-01

    In order to meet the requirement of separating power plants from power network and that of the competition based power transaction in power market, the pricing decision support system for generation companies (GCPDSS) is built in electricity market. This paper introduces the conception of intelligent decision support system (IDSS) and puts emphasis on the systematical structural framework,work process, design principal, and fundamental function of GCPDSS. The system has the module to analyze the cost, to forecast the demand of power, to construct the pricing strategies, to manage the pricing risk, and to dispatch giving the pricing strategies.The case study illustrates that the friendly window-based user interface of the system enables the user to take full advantage of the capabilities of the system in order to make effective real-time decisions.

  18. Automatic Generation of Symbolic Model for Parameterized Synchronous Systems

    Institute of Scientific and Technical Information of China (English)

    Wei-Wen Xu

    2004-01-01

    With the purpose of making the verification of parameterized system more general and easier, in this paper, a new and intuitive language PSL (Parameterized-system Specification Language) is proposed to specify a class of parameterized synchronous systems. From a PSL script, an automatic method is proposed to generate a constraint-based symbolic model. The model can concisely symbolically represent the collections of global states by counting the number of processes in a given state. Moreover, a theorem has been proved that there is a simulation relation between the original system and its symbolic model. Since the abstract and symbolic techniques are exploited in the symbolic model, state-explosion problem in traditional verification methods is efficiently avoided. Based on the proposed symbolic model, a reachability analysis procedure is implemented using ANSI C++ on UNIX platform. Thus, a complete tool for verifying the parameterized synchronous systems is obtained and tested for some cases. The experimental results show that the method is satisfactory.

  19. Applications of Next-generation Sequencing in Systemic Autoimmune Diseases

    Institute of Scientific and Technical Information of China (English)

    Yiyangzi Ma; Na Shi; Mengtao Li; Fei Chen; Haitao Niu

    2015-01-01

    Systemic autoimmune diseases are a group of heterogeneous disorders caused by both genetic and environmental factors. Although numerous causal genes have been identified by genome-wide association studies (GWAS), these susceptibility genes are correlated to a relatively low disease risk, indicating that environmental factors also play an important role in the pathogen-esis of disease. The intestinal microbiome, as the main symbiotic ecosystem between the host and host-associated microorganisms, has been demonstrated to regulate the development of the body’s immune system and is likely related to genetic mutations in systemic autoimmune diseases. Next-generation sequencing (NGS) technology, with high-throughput capacity and accuracy, provides a powerful tool to discover genomic mutations, abnormal transcription and intestinal microbiome identification for autoimmune diseases. In this review, we briefly outlined the applications of NGS in systemic autoimmune diseases. This review may provide a reference for future studies in the pathogenesis of systemic autoimmune diseases.

  20. Distribution System Planning With Distributed Generations Considering Benefits and Costs

    Directory of Open Access Journals (Sweden)

    Saeid Soudi

    2013-10-01

    Full Text Available One of the methods used in the design and utilization of distribution systems to improve power quality and reliability of load power supply of consumers, is the application of distributed generation (DG sources. In this paper, a new method is proposed for the design and utilization of distribution networks with DG resources application by finding the optimal sitting and sizing of generated power of DG with the aim of maximization of its benefits to costs. The benefits for DG are considered as system losses reduction, system reliability improvement and benefits from the sale electricity or from lack of purchase of electricity from the main system. The costs of DG are considered as initial capital, maintenance and operation cost and investment cost. In this paper to solve the optimal sitting and sizing problem a Modified particle swarm optimization (PSO is applied. Simulations are presented on a 69-bus test distribution system to verify the effectiveness of the proposed method. Results showed that the proposed high-power method to find the optimal points of problem is faster and application of DG resources reduced the losses, costs and improved the system voltage profile.