WorldWideScience

Sample records for gas journal bearing

  1. On The Modeling Of Hybrid Aerostatic - Gas Journal Bearings

    Morosi, Stefano; Santos, Ilmar

    2010-01-01

    of a compressible fluid film journal bearing. Control forces are generated by injecting pressurized air into the bearing gap through orifices located on the bearing walls. A modified form of the compressible Reynolds equation for active lubrication is derived. By solving this equation, stiffness and damping......Gas journal bearing have been increasingly adopted in modern turbo-machinery applications, as they meet the demands of operation at higher rotational speeds, in clean environment and great efficiency. Due to the fact that gaseous lubricants, typically air, have much lower viscosity than more...

  2. On The Modelling Of Hybrid Aerostatic - Gas Journal Bearings

    Morosi, Stefano; Santos, Ilmar

    2011-01-01

    modeling for hybrid lubrication of a compressible fluid film journal bearing. Additional forces are generated by injecting pressurized air into the bearing gap through orifices located on the bearing walls. A modified form of the compressible Reynolds equation for active lubrication is derived. By solving......Gas journal bearing have been increasingly adopted in modern turbo-machinery applications, as they meet the demands of operation at higher rotational speeds, in clean environment and great efficiency. Due to the fact that gaseous lubricants, typically air, have much lower viscosity than more...

  3. Characterization and measurement of hybrid gas journal bearings

    Lawrence, Tom Marquis

    This thesis concentrates on the study of hybrid gas journal bearings (bearings with externally pressurized mass addition). It differs from most work in that it goes back to "basics" to explore the hydrodynamic phenomena in the bearing gap. The thesis compares geometrically identical bearings with 2 configurations of external pressurization, porous liners where mass-addition compensation is varied by varying the liner's permeability, and bushings with 2 rows of 6 feedholes where the mass-addition compensation is varied by the feedhole diameter. Experimentally, prototype bearings with mass-addition compensation that spans 2 orders of magnitude with differing clearances are built and their aerostatic properties and mass addition characteristics are thoroughly tested. The fundamental equations for compressible, laminar, Poiseuille flow are used to suggest how the mass flow "compensation" should be mathematically modeled. This is back-checked against the experimental mass flow measurements and is used to determine a mass-addition compensation parameter (called Kmeas) for each prototype bushing. In so doing, the methodology of modeling and measuring the mass addition in a hybrid gas bearing is re-examined and an innovative, practical, and simple method is found that makes it possible to make an "apples-to-apples" comparison between different configurations of external pressurization. This mass addition model is used in conjunction with the Reynolds equation to perform theory-based numerical analysis of virtual hybrid gas journal bearings (CFD experiments). The first CFD experiments performed use virtual bearings modeled to be identical to the experimental prototypes and replicate the experimental work. The results are compared and the CFD model is validated. The ontological significance of appropriate dimensionless similitude parameters is re-examined and a, previously lacking, complete set of similitude factors is found for hybrid bearings. A new practical method is

  4. Journal bearing

    Menke, John R.; Boeker, Gilbert F.

    1976-05-11

    1. An improved journal bearing comprising in combination a non-rotatable cylindrical bearing member having a first bearing surface, a rotatable cylindrical bearing member having a confronting second bearing surface having a plurality of bearing elements, a source of lubricant adjacent said bearing elements for supplying lubricant thereto, each bearing element consisting of a pair of elongated relatively shallowly depressed surfaces lying in a cylindrical surface co-axial with the non-depressed surface and diverging from one another in the direction of rotation and obliquely arranged with respect to the axis of rotation of said rotatable member to cause a flow of lubricant longitudinally along said depressed surfaces from their distal ends toward their proximal ends as said bearing members are rotated relative to one another, each depressed surface subtending a radial angle of less than 360.degree., and means for rotating said rotatable bearing member to cause the lubricant to flow across and along said depressed surfaces, the flow of lubricant being impeded by the non-depressed portions of said second bearing surface to cause an increase in the lubricant pressure.

  5. Journal Bearings

    Renato Brancati

    1999-01-01

    determined after acquiring and analysing the orbits described by the journal axis for assigned unbalance values in different operating conditions. Analysis of the results shows some particular operating features that were not entirely predicted by the theoretical model and which may give rise to malfunctions in the rotor-tilting pad bearings system. The tests were carried out in the rotor dynamics laboratory of the Dipartimento di Ingegneria Meccanica per l'Energetica at the University of Naples.

  6. Active lubrication applied to radial gas journal bearings. Part 1: Modeling

    Morosi, Stefano; Santos, Ilmar

    2011-01-01

    Active bearings represent a mechatronic answer to the growing industrial need to high performance turbomachinery. The present contribution aims at demonstrate the feasibility of applying active lubrication to gas journal bearings. The principle of operation is to generate active forces by regulat...

  7. Bifurcation and nonlinear dynamic analysis of a flexible rotor supported by relative short gas journal bearings

    Wang, C.-C.; Jang, M.-J.; Yeh, Y.-L.

    2007-01-01

    This paper studies the bifurcation and nonlinear behaviors of a flexible rotor supported by relative short gas film bearings. A time-dependent mathematical model for gas journal bearings is presented. The finite difference method with successive over relation method is employed to solve the Reynolds' equation. The system state trajectory, Poincare maps, power spectra, and bifurcation diagrams are used to analyze the dynamic behavior of the rotor and journal center in the horizontal and vertical directions under different operating conditions. The analysis reveals a complex dynamic behavior comprising periodic and subharmonic response of the rotor and journal center. This paper shows how the dynamic behavior of this type of system varies with changes in rotor mass and rotational velocity. The results of this study contribute to a further understanding of the nonlinear dynamics of gas film rotor-bearing systems

  8. Effect of boundary conditions on the performances of gas-lubricated micro journal bearing

    Wang Sheng; Lei Kangbin; Kiwamu, Kase; Luo Xilian; Gu Zhaolin

    2010-01-01

    As significant components of micromechanics, gas-lubricated microbearings are more prevalent for their special advantages than other types. The fluid dynamics of the microbearing is different from their larger cousins due to the noncontinuum effect and surface-dominated effect, which may make the Navier-Stokes equations invalid. In this paper, by considering the accommodation coefficients on journal (α i ) and that on bearing (α o ) separately, the microbearings with different bearing numbers under the assumption of large L/D (length to diameter) are simulated using direct simulation Monte Carlo (DSMC) program incorporated with a Volume-CAD software. The diffuse reflection model and Cercignani-Lampis-Lord (CLL) model are applied to model the molecule-surface interaction. The flow field characteristics, as well as the performances of gas-lubricated journal bearings including load-carrying capacity, attitude angle and bearing drag are obtained. The results reveal that α i and α o have different effects to flow field characteristics and bearing performances. The bearing number has significantly impact on the bearing performances. The method developed in this paper would be very useful for designing and evaluating the gas-lubricated journal microbearing.

  9. GAS BEARING

    Skarstrom, C.W.

    1960-09-01

    A gas lubricated bearing for a rotating shaft is described. The assembly comprises a stationary collar having an annular member resiliently supported thereon. The collar and annular member are provided with cooperating gas passages arranged for admission of pressurized gas which supports and lubricates a bearing block fixed to the rotatable shaft. The resilient means for the annular member support the latter against movement away from the bearing block when the assembly is in operation.

  10. Performance of gas-lubricated cruciform-mounted tilting-pad journal bearings and a damped flexibly mounted spiral-groove thrust bearing

    Ream, L. W.

    1974-01-01

    A test program was conducted to determine the performance characteristics of gas-lubricated cruciform-mounted tilting-pad journal bearings and a damped spiral-groove thrust bearing designed for the Brayton cycle rotating unit (BRU). Hydrostatic, hybrid (simultaneously hydrostatic and hydrodynamic), and hydrodynamic tests were conducted in argon gas at ambient pressure and temperature ranges representative of operation to the 10.5 kWe BRU power-generating level. Performance of the gas lubricated bearings is presented including hydrostatic gas flow rates, bearing clearances, bearing temperatures, and transient performance.

  11. On the stability analysis of flexible rotors supported by Hybrid Aerostatic - Gas Journal Bearings

    Morosi, Stefano; Santos, Ilmar

    Modern turbo-machinery applications, high speed machine tools, laboratory equipment require nowadays ever-growing rotational speeds and high degree of precision and reliability. Gas journal bearing have been in many extents employed as they meet the demands of performing at high speeds, in clean...... environment and great efficiency. However, the drawback are inherent poor carrying capacity and dynamic characteristics of passive systems, which often translate to a reduced range of stability. In order to enhance these characteristics, one solution is to combine the hydrodynamic effect with the addition...... form of the compressible Reynolds equation for active lubrication is derived. Particular attention is given to the injections terms and a comparison is carried on between fully nonlinear and linearized expressions. By solving this equation, stiffness and damping coefficients can be determined...

  12. Active lubrication applied to radial gas journal bearings. Part 2: Modelling improvement and experimental validation

    Pierart, Fabián G.; Santos, Ilmar F.

    2016-01-01

    Actively-controlled lubrication techniques are applied to radial gas bearings aiming at enhancing one of their most critical drawbacks, their lack of damping. A model-based control design approach is presented using simple feedback control laws, i.e. proportional controllers. The design approach...... by finite element method and the global model is used as control design tool. Active lubrication allows for significant increase in damping factor of the rotor-bearing system. Very good agreement between theory and experiment is obtained, supporting the multi-physic design tool developed....

  13. Journal bearing impedance descriptions for rotordynamic applications

    Childs, D.W.; Moes, H.; Leeuwen, van H.J.

    1977-01-01

    Bearing impedance vectors are introduced for plain journal bearings which define the bearing reaction force components as a function of the bearing motion. Impedance descriptions are developed directly for the approximate Ocvirk (short) and Sommerfeld (long) bearing solutions. The impedance vector

  14. Noise estimation of oil lubricated journal bearings

    Rho, Byoung Hoo; Kim, Kyung Woong

    2003-01-01

    Noise estimating procedures of oil lubricated journal bearings are presented. Nonlinear analysis of rotor-bearing system including unbalance mass of the rotor is performed in order to obtain acoustical properties of the bearing. Acoustical properties of the bearing are investigated through frequency analysis of the pressure fluctuation of the fluid film calculated from the nonlinear analysis. Noise estimating procedures presented in this paper could aid in the evaluation and understanding of acoustical properties of oil lubricated journal bearings

  15. Journal and Wave Bearing Impedance Calculation Software

    Hanford, Amanda; Campbell, Robert

    2012-01-01

    The wave bearing software suite is a MALTA application that computes bearing properties for user-specified wave bearing conditions, as well as plain journal bearings. Wave bearings are fluid film journal bearings with multi-lobed wave patterns around the circumference of the bearing surface. In this software suite, the dynamic coefficients are outputted in a way for easy implementation in a finite element model used in rotor dynamics analysis. The software has a graphical user interface (GUI) for inputting bearing geometry parameters, and uses MATLAB s structure interface for ease of interpreting data. This innovation was developed to provide the stiffness and damping components of wave bearing impedances. The computational method for computing bearing coefficients was originally designed for plain journal bearings and tilting pad bearings. Modifications to include a wave bearing profile consisted of changing the film thickness profile given by an equation, and writing an algorithm to locate the integration limits for each fluid region. Careful consideration was needed to implement the correct integration limits while computing the dynamic coefficients, depending on the form of the input/output variables specified in the algorithm.

  16. Nonlinear Dynamic Response of Compliant Journal Bearings

    Glavatskih S.

    2012-07-01

    Full Text Available This paper investigates the dynamic response of the compliant tilting pad journal bearings subjected to synchronous excitation. Bearing compliance is affected by the properties of pad liner and pad support geometry. Different unbalance eccentricities are considered. It is shown that bearing dynamic response is non-linear. Journal orbit complexity increases with pad compliance though the orbit amplitudes are marginally affected at low loads. At high loads, the journal is forced to operate outside the bearing clearance. The polymer liner reduces the maximum oil film pressure by a factor of 2 when compared to the white metal liner. The nonlinear dynamic response of compliant tilting pad journal bearings is thoroughly discussed.

  17. Noise of oil lubricated journal bearings

    Rho, Byoung Hoo; Kim, Kyung Woong

    2002-01-01

    The purpose of the paper is to provide a procedure to calculate the noise of oil lubricated journal bearings. To do this, the nonlinear transient analysis of rotor-bearing system including rotor imbalance is performed. Acoustical properties of the bearing are investigated through frequency analysis of the pressure fluctuation of the fluid film calculated from the nonlinear analysis. Furthermore, a transmission theory of plane waves on a boundary of the outer surface of the bearing is used to obtain the sound pressure level of the bearing. Results show that the sound pressure level of the bearing can be increased with the rotational speed of the rotor although the whirl amplitude of the rotor is decreased at high speed. Noise estimating procedures presented in this paper could be an aid in the evaluation and understanding of acoustical properties of oil lubricated journal bearings

  18. 49 CFR 230.102 - Tender plain bearing journal boxes.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Tender plain bearing journal boxes. 230.102... Locomotives and Tenders Running Gear § 230.102 Tender plain bearing journal boxes. Plain bearing journal boxes... expected to damage the bearing; or have a detrimental effect on the lubrication of the journal and bearing...

  19. Measurement of Wear in Radial Journal Bearings

    Ligterink, D.J.; Ligterink, D.J.; de Gee, A.W.J.

    1996-01-01

    this article, the measurement of wear in radial journal bearings is discussed, where a distinction is made between stationary and non-stationary contact conditions. Starting with Holm/Archard's wear law, equations are derived for the calculation of the specific wear rate k of the bearing material as

  20. Active Vibration Control of Hydrodynamic Journal Bearings

    Tůma, J.; Šimek, J.; Škuta, J.; Los, J.; Zavadil, J.

    Rotor instability is one of the most serious problems of high-speed rotors supported by sliding bearings. With constantly increasing parameters, new machines problems with rotor instability are encountered more and more often. Even though there are many solutions based on passive improvement of the bearing geometry to enlarge the operational speed range of the journal bearing, the paper deals with a working prototype of a system for the active vibration control of journal bearings with the use of piezoactuators. The actively controlled journal bearing consists of a movable bushing, which is actuated by two piezoactuators. It is assumed that the journal vibration is measured by a pair of proximity probes. Force produced by piezoactuators and acting at the bushing is controlled according to error signals derived from the proximity probe output signals. The active vibration control was tested with the use of a test rig, which consists of a rotor supported by two controllable journal bearings and driven by an inductive motor up to 23,000 rpm. As it was proved by experiments the active vibration control extends considerably the range of the rotor operational speed.

  1. Experimental Grey Box Model Identification of an Active Gas Bearing

    Theisen, Lukas Roy Svane; Pierart Vásquez, Fabián Gonzalo; Niemann, Hans Henrik

    2014-01-01

    in a dynamic model of an active gas bearing and subsequent control loop design. A grey box model is determined based on experiments where piezo actuated valves are used to perturb the journal and hence excite the rotor-bearing system. Such modelling from actuator to output is shown to effciently support...

  2. Modeling of Hybrid Permanent Magnetic-Gas Bearings

    Morosi, Stefano; Santos, Ilmar

    2009-01-01

    Modern turbomachinery applications require nowadays ever-growing rotational speeds and high degree of reliability. It then becomes natural to focus the attention of the research to contact-free bearings elements. The present alternatives focus on gas lubricated journal bearings or magnetic bearings....... In the present paper, a detailed mathematical modeling of the gas bearing based on the compressible form of the Reynolds equation is presented. Perturbation theory is applied in order to identify the dynamic characteristic of the bearing. Due to the simple design of the magnetic bearings elements - being...... the rotor equilibrium position can be made independent on the rotational speed and applied load; it becomes function of the passive magnetic bearing offset. By adjusting the offset it is possible to significantly influence the dynamic coefficients of the hybrid bearing....

  3. Wear numbers for ball cup and journal bearings

    Ligterink, D.J.; Moes, H.

    1980-01-01

    A wear number is defined for ball cup bearings and for journal bearings where the cup and the cylindrical bearing are made of soft material. This dimensionless wear number provides a relation between the following five quantities: the radius of the ball or the length of the journal bearing in

  4. 49 CFR 230.103 - Tender roller bearing journal boxes.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Tender roller bearing journal boxes. 230.103... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller bearing journal boxes shall be maintained in a safe and suitable condition. ...

  5. Tribology experiment. [journal bearings and liquid lubricants

    Wall, W. A.

    1981-01-01

    A two-dimensional concept for Spacelab rack 7 was developed to study the interaction of liquid lubricants and surfaces under static and dynamic conditions in a low-gravity environment fluid wetting and spreading experiments of a journal bearing experiments, and means to accurately measure and record the low-gravity environment during experimentation are planned. The wetting and spreading process of selected commercial lubricants on representative surface are to the observes in a near-zero gravity environment.

  6. Improvement of journal bearing operation at heavy misalignment using bearing flexibility and compliant liners

    Thomsen, Kim; Klit, Peder

    2012-01-01

    A flexure journal bearing design is proposed that will improve operational behaviour of a journal bearing at pronounced misalignment. Using a thermoelastohydrodynamic model, it is shown that the proposed flexure journal bearing has vastly increased the hydrodynamic performance compared to the stiff...... bearing when misaligned. The hydrodynamic performance is evaluated on lubricant film thickness, pressure and temperature. Furthermore, the influence of a compliant bearing liner is investigated and it is found that it increases the hydrodynamic performance when applied to a stiff bearing, whereas...... the liner has practically no influence on the flexure journal bearing's performance....

  7. Monitoring of lubrication conditions in journal bearing by acoustic emission

    Yoon, Dong Jin; Kwon, Oh Yang; Jung, Min Hwa

    1993-01-01

    Systems with journal bearings generally operate in large scale and under severe loading conditions such as steam generator turbines and internal combustion engines, in contrast to the machinery using rolling element bearings. Failure of the bearings in these machinery can result in the system breakdown. To avoid the time consuming repair and considerable economic loss, the detection of incipient failure in journal bearings becomes very important. In this experimental approach, acoustic emission monitoring is employed to the detection of incipient failure caused by intervention of foreign particles most probable in the journal bearing systems. It has been known that the intervention of foreign materials, insufficient lubrication and misassembly etc. are principal factors to cause bearing failure and distress. The experiment was conducted under such designed conditions as inserting alumina particles to the lubrication layer in the simulated journal bearing system. The results showed that acoustic emission could be an effective tool to detect the incipient failure in journal bearings.

  8. Transient response of two lobe aerodynamic journal bearing

    Saurabh Kumar Yadav

    2018-03-01

    Full Text Available The dynamic behavior of a rotor-dynamic system is greatly affected by the performance of aerodynamic bearing and the performance of bearing is characterized by the stiffness and damping coefficients. In the present work, stiffness and damping coefficients of bearing are computed and the performance of the bearing is greatly changed with the change in bearing air film profile. The effect of lobe offset factors on the transient performance of aerodynamic bearing is presented. Bifurcation and Poincare diagrams of two lobe journal bearing have been presented for different offset factors. A bearing designer can judge the bearing performance based on bifurcation diagrams.

  9. Technical Development Path for Gas Foil Bearings

    Dellacorte, Christopher

    2016-01-01

    Foil gas bearings are in widespread commercial use in air cycle machines, turbocompressors and microturbine generators and are emerging in more challenging applications such as turbochargers, auxiliary power units and propulsion gas turbines. Though not well known, foil bearing technology is well over fifty years old. Recent technological developments indicate that their full potential has yet to be realized. This paper investigates the key technological developments that have characterized foil bearing advances. It is expected that a better understanding of foil gas bearing development path will aid in future development and progress towards more advanced applications.

  10. Stabilizing gas bearing in free piston machines

    Dhar, Manmohan (Inventor)

    1992-01-01

    In a free piston engine, to reduce dynamic loads on the reciprocating elements caused by a time varying pressure gradient across the gas bearing and close clearance seals provided therein, drain galleries are incorporated at the ends of the gas bearings to isolate the same, and circumferentially spaced grooves are incorporated in the close clearance seal region.

  11. On the computation of electrical resistance of hydrodynamic journal bearing

    Eleonora Pop

    2014-12-01

    Full Text Available The paper approaches the mathematical model of electrical resistance of hydrodynamic journal bearing under different parameters of operation so as to predict bearing performance and safe load carrying capacity. The currents circulating in the journal bearing of electrical machine causes reducing of lifespan by appearance of pitting on their surface and the degradation of the lubricant. In a hydrodynamic journal bearing, the zone of minimum film thickness, load-carrying oil film varies along the circumference of a bearing through its length. This has been found to form a capacitor of varying capacitance between the journal and the bearings dependent on permittivity of the lubricant used, the bearing length, the eccentricity ratio and the clearance ratio. Besides this, load-carrying on oil film offers resistance that depends on operating parameters and resistivity of the lubricant.

  12. Numerical investigation of cavitation flow in journal bearing geometry

    Stücke P.; Schmidt M.; Riedel M.

    2013-01-01

    The appearance of cavitation is still a problem in technical and industrial applications. Especially in automotive internal combustion engines, hydrodynamic journal bearings are used due to their favourable wearing quality and operating characteristics. Cavitation flows inside the bearings reduces the load capacity and leads to a risk of material damages. Therefore an understanding of the complex flow phenomena inside the bearing is necessary for the design development of hydrodynamic journal...

  13. Numerical investigation of cavitation flow in journal bearing geometry

    Riedel, M.; Schmidt, M.; Stücke, P.

    2013-04-01

    The appearance of cavitation is still a problem in technical and industrial applications. Especially in automotive internal combustion engines, hydrodynamic journal bearings are used due to their favourable wearing quality and operating characteristics. Cavitation flows inside the bearings reduces the load capacity and leads to a risk of material damages. Therefore an understanding of the complex flow phenomena inside the bearing is necessary for the design development of hydrodynamic journal bearings. Experimental investigations in the fluid domain of the journal bearing are difficult to realize founded by the small dimensions of the bearing. In the recent years more and more the advantages of the computational fluid dynamics (CFD) are used to investigate the detail of the cavitation flows. The analysis in the paper is carried out in a two-step approach. At first an experimental investigation of journal bearing including cavitation is selected from the literature. The complex numerical model validated with the experimental measured data. In a second step, typically design parameters, such as a groove and feed hole, which are necessary to distribute the oil supply across the gap were added into the model. The paper reflects on the influence of the used design parameters and the variation of the additional supply flow rate through the feed hole regarding to cavitation effects in the bearing. Detailed pictures of the three-dimensional flow structures and the cavitation regions inside the flow film of the bearing are presented.

  14. Numerical investigation of cavitation flow in journal bearing geometry

    Stücke P.

    2013-04-01

    Full Text Available The appearance of cavitation is still a problem in technical and industrial applications. Especially in automotive internal combustion engines, hydrodynamic journal bearings are used due to their favourable wearing quality and operating characteristics. Cavitation flows inside the bearings reduces the load capacity and leads to a risk of material damages. Therefore an understanding of the complex flow phenomena inside the bearing is necessary for the design development of hydrodynamic journal bearings. Experimental investigations in the fluid domain of the journal bearing are difficult to realize founded by the small dimensions of the bearing. In the recent years more and more the advantages of the computational fluid dynamics (CFD are used to investigate the detail of the cavitation flows. The analysis in the paper is carried out in a two-step approach. At first an experimental investigation of journal bearing including cavitation is selected from the literature. The complex numerical model validated with the experimental measured data. In a second step, typically design parameters, such as a groove and feed hole, which are necessary to distribute the oil supply across the gap were added into the model. The paper reflects on the influence of the used design parameters and the variation of the additional supply flow rate through the feed hole regarding to cavitation effects in the bearing. Detailed pictures of the three-dimensional flow structures and the cavitation regions inside the flow film of the bearing are presented.

  15. Studying fluid squeeze characteristics for aerostatic journal bearing

    Abdel-Rahman, Gamal M.

    2008-01-01

    The Reynolds equation for studying fluid squeeze of aerostatic journal bearing is solved numerically by considering the quasi-steady behavior of the air film. The radial displacement can influence the air film thickness modifying the pressure distribution in the journal-bearing gap. Also, the variations in the seal characteristics with eccentricity, time, squeeze number, length-to-diameter and supply pressure are presented. The numerical results for the squeeze load-carrying capacity are given in a non-dimensional form

  16. Development of AE monitoring system for journal bearing

    Yoon, Dong Jin; Kwon, Oh Yang; Chung, Min Hwa

    1994-01-01

    For the purpose of monitoring of the bearing conditions in rotating machinery, a system for journal bearing diagnosis by AE was developed. Acoustic emission technique is used to detect abnormal conditions in the bearing system. And various data such as AE events, rms voltage level of AE signals, and AE parameters were acquired during experiments with the simulated journal bearing system. Based on the above results and practical application for power plant, algorithms and judgement criteria for diagnosis system was accomplished. Bearing diagnosis system is composed of four parts as follows : sensing part for AE sensor and preamplifier, signal processing part for rms-to-dc converting to measure AE rms voltage, interface part for connecting rms signal to PC using A/D converter, graphic display and software part for display of bearing condition and for managing of diagnosis program.

  17. Parametric studies on floating pad journal bearing for high speed cryogenic turboexpanders

    Jain, A.; Jadhav, M. M.; Karimulla, S.; Chakravarty, A.

    2017-12-01

    Most modern medium and large capacity helium liquefaction/refrigeration plants employ high speed cryogenic turboexpanders in their refrigeration/liquefaction cycles as active cooling devices. The operating speed of these turboexpanders is in the range of 3000-5000 Hz and hence specialized types of bearings are required. Floating pad journal bearing, which is a special type of tilting pad journal bearing, where mechanical pivots are absent and pads are fully suspended in gas, can be a good solution for stable operation of these high speed compact rotors. The pads are separated from shaft as well as from housing by fluid film between them, and both these sides of pad are interconnected by a network of feed holes. The work presented in this article aims to characterize floating pad journal bearings through parametric studies. The steady state performance characteristics of the bearing are represented by load capacity, stiffness coefficients and heat generation rate of the bearing. The geometrical parameters such as bearing clearances, preload of pads, etc. are varied and performance characteristics of the floating pad journal bearing are studied and presented. The dependence of stiffness coefficients on rotational speed of shaft is also analyzed.

  18. An air bearing system for small high speed gas turbines

    Turner, A. B.; Davies, S. J.; Nimir, Y. L.

    1994-03-01

    This paper describes the second phase of an experimental program concerning the application of air bearings to small turbomachinery test rigs and small gas turbines. The first phase examined externally pressurized (EP) journal bearings, with a novel EP thrust bearing, for application to 'warm air' test rigs, and was entirely successful at rotational speeds in excess of 100,000 rpm. This second phase examined several designs of tilting pad-spiring journal bearings, one with a novel form of externally pressurized pad, but all using the original EP thrust bearing. The designs tested are described, including some oscillogram traces, for tests up to a maximum of 70,000 rpm; the most successful using a carbon pad-titanium beam spring arrangement. The thrust bearing which gave trouble-free operation throughout, is also described. The results of an original experiment to measure the 'runway speed' of a radial inflow turbine are also presented, which show that overspeeds of 58 percent above the design speed can result from free-power turbine coupling failure.

  19. Numerical analysis of hydrodynamic journal bearings lubricated with ferrofluid

    Montazeri, H.

    2008-01-01

    The current work focuses on studying the hydrodynamic characteristics of flow in journal bearings lubricated with ferrofluid. The bearing has an infinite length and operates under incompressible laminar flow and steady conditions. Assuming linear behaviour for the magnetic material of the

  20. Acoustic Emission Monitoring of Incipient in Journal Bearings - Part I : Detectability and measurement for bearing damages

    Yoon, Dong Jin; Kwon, Oh Yang; Chung, Min Hwa; Kim, Kyung Woong

    1994-01-01

    In contrast to the machinery using rolling element bearings, systems with journal bearings generally operate in large scale and under severe loading condition such as steam generator turbines and internal combustion engines. Failure of the bearings in these machinery can result in the system breakdown. To avoid the time consuming repair and considerable economic loss, the detection of incipient failure in journal bearings becomes very important. In this experimental approach, acoustic emission monitoring is applied to the detection of incipient failure caused by several types of abnormal operating condition most probable in the journal bearing systems. It has been known that the intervention of foreign materials, insufficient lubrication and misassembly etc. are principal factors to cause bearing failure and distress. The experiment was conducted under such designed conditions as hard particles in the lubrication layer, insufficient lubrication, and metallic contact in the simulated journal bearing system. The results showed that acoustic emission could be an effective tool to detect the incipient failure in journal bearings

  1. Mathematical model for temperature change of a journal bearing

    Antunović Ranko

    2018-01-01

    Full Text Available In this work, a representative mathematical model has been developed, which reliably describes the heating and cooling of a journal bearing as a result of its malfunctioning, and the model has been further confirmed on a test bench. The bearing model was validated by using analytical modeling methods, i. e. the experimental results were compared to the data obtained by analytical calculations. The regression and variance analysis techniques were applied to process the recorded data, to test the mathematical model and to define mathematical functions for the heating/cooling of the journal bearing. This investigation shows that a representative model may reliably indicate the change in the thermal field, which may be a consequence of journal bearing damage.

  2. A study on synchronously whirling motion of hydrodynamic journal bearings

    Rho, Byoung Hoo; Kim, Kyung Woong

    2001-01-01

    In this paper, a control algorithm which is synchronously excitation the bearing with whirl speed of rotor is employed to suppress the whirl instability and unbalance response of the rotor-bearing system. Also, the cavitation algorithm implementing the Jakobsson-Floberg-Olsson boundary condition is adopted to predict cavitation regions in the fluid film more accurately than a conventional analysis with the Renolds condition. The stabilities and unbalance responses of the rotor-bearing system are investigated for various control gains and phase differences between the bearing and journal motion. It is shown that the unbalance response of the system can be greatly improved by synchronous control of the bearing, and there is an optimum phase difference, which gives the minimum unbalance response of the system, for given operating condition. It is also found that the onset speed of the instability can be greatly increased by synchronous control of the bearing

  3. A study on synchronously whirling motion of hydrodynamic journal bearings

    Rho, Byoung Hoo; Kim, Kyung Woong [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

    2001-09-01

    In this paper, a control algorithm which is synchronously excitation the bearing with whirl speed of rotor is employed to suppress the whirl instability and unbalance response of the rotor-bearing system. Also, the cavitation algorithm implementing the Jakobsson-Floberg-Olsson boundary condition is adopted to predict cavitation regions in the fluid film more accurately than a conventional analysis with the Renolds condition. The stabilities and unbalance responses of the rotor-bearing system are investigated for various control gains and phase differences between the bearing and journal motion. It is shown that the unbalance response of the system can be greatly improved by synchronous control of the bearing, and there is an optimum phase difference, which gives the minimum unbalance response of the system, for given operating condition. It is also found that the onset speed of the instability can be greatly increased by synchronous control of the bearing.

  4. Static, Dynamic, and Thermal Properties of Compressible Fluid Film Journal Bearings

    Paulsen, Bo Terp; Morosi, Stefano; Santos, Ilmar

    2011-01-01

    fluid film journal bearing, in order to identify when this type of analysis should be of concern. Load capacity, stiffness, and damping coefficients are determined by the solution of the standard Reynolds equation coupled to the energy equation. Numerical investigations show how bearing geometry......, and work great efficiency. A great deal of literature has concentrated on the analysis and prediction of the static and dynamic performance of gas bearings, assuming isothermal conditions. The present contribution presents a detailed mathematical modeling for nonisothermal lubrication of a compressible...

  5. Modeling of Tilting-Pad Journal Bearings with Transfer Functions

    J. A. Vázquez

    2001-01-01

    Full Text Available Tilting-pad journal bearings are widely used to promote stability in modern rotating machinery. However, the dynamics associated with pad motion alters this stabilizing capacity depending on the operating speed of the machine and the bearing geometric parameters, particularly the bearing preload. In modeling the dynamics of the entire rotor-bearing system, the rotor is augmented with a model of the bearings. This model may explicitly include the pad degrees of freedom or may implicitly include them by using dynamic matrix reduction methods. The dynamic reduction models may be represented as a set of polynomials in the eigenvalues of the system used to determine stability. All tilting-pad bearings can then be represented by a fixed size matrix with polynomial elements interacting with the rotor. This paper presents a procedure to calculate the coefficients of polynomials for implicit bearing models. The order of the polynomials changes to reflect the number of pads in the bearings. This results in a very compact and computationally efficient method for fully including the dynamics of tilting-pad bearings or other multiple degrees of freedom components that interact with rotors. The fixed size of the dynamic reduction matrices permits the method to be easily incorporated into rotor dynamic stability codes. A recursive algorithm is developed and presented for calculating the coefficients of the polynomials. The method is applied to stability calculations for a model of a typical industrial compressor.

  6. Acoustic Emission Monitoring of Incipient Failure in Journal Bearings( III ) - Development of AE Diagnosis System for Journal Bearings -

    Chung, Min Hwa; Cho, Yong Sang; Yoon, Dong Jin; Kwon, Oh Yang

    1996-01-01

    For the condition monitoring of the journal bearing in rotating machinery, a system for their diagnosis by acoustic emission(AE) was developed. AE has been used to detect abnormal conditions in the bearing system. It was found from the field application study as well as the laboratory experiment using a simulated journal bearing system that AE RMS voltage was the most efficient parameter for the purpose of current study. Based on the above results, algorithms and judgement criteria for the diagnosis system was established. The system is composed of four parts as follows: the sensing part including AE sensor and preamplifier, the signal processing part for RMS-to-DC conversion to measure AE ms voltage, the interface part for transferring RMS voltage data into PC using A/D converter, and the software part including the graphic display of bearing conditions and the diagnosis program

  7. Bearing Witness: Citizen Journalism and Human Rights Issues

    Allan, Stuart; Sonwalkar, Prasun; Carter, Cynthia

    2007-01-01

    This article assesses the potential of online news reporting to create discursive spaces for emphatic engagement--of bearing witness--at a distance, especially where human rights violations are concerned. Taking as its focus the emergent forms and practices of citizen journalism, it examines the spontaneous actions of ordinary people compelled to…

  8. Dynamic characteristics of polymer faced tilting pad journal bearings

    Simmons, Gregory F.; Cerda Varela, Alejandro Javier; Santos, Ilmar

    2014-01-01

    Dynamic characteristics of polymer faced tilting pad journal bearings are presented. Investigations are conducted using a single pad, load on pad configuration over a range of shaft speeds and loads. Two polyether ether ketone (PEEK) faced pads, one polytetrafluoroethylene (PTFE) faced pad and two...

  9. Axial force in a superconductor magnet journal bearing

    Postrekhin, E.; Chong, Wang; Ki Bui, Ma; Chen, Quark; Chu, Wei-Kan

    Using superconductors and magnets, a journal bearing could be made from a permanent magnet cylinder in a superconductor ring. We have assembled a prototype superconductor magnet journal bearing of this configuration, and investigated the behavior of the axial force that it can provide. We have put together a numerical model of the interaction between the permanent magnet and the superconductor that is capable of describing these experimental results semi-quantitatively. Combining direct experimental measurements and using the numerical models proposed, we have achieved a qualitative understanding of the behavior of the axial force and its relationship of to the dimensions of the magnet and material quality such as the homogeneity of the superconductor that constitute the bearing.

  10. Dynamic behavior of air lubricated pivoted-pad journal-bearing, rotor system. 2: Pivot consideration and pad mass

    Nemeth, Z. N.

    1972-01-01

    Rotor bearing dynamic tests were conducted with tilting-pad journal bearings having three different pad masses and two different pivot geometries. The rotor was vertically mounted and supported by two three-pad tilting-pad gas journal bearings and a simple externally pressurized thrust bearing. The bearing pads were 5.1 cm (2.02 in.) in diameter and 2.8 cm (1.5 in.) long. The length to diameter ratio was 0.75. One pad was mounted on a flexible diaphragm. The bearing supply pressure ranged from 0 to 690 kilonewtons per square meter (0 to 100 psig), and speeds ranged to 38,500 rpm. Heavy mass pad tilting-pad assemblies produced three rotor-bearing resonances above the first two rotor critical speeds. Lower supply pressure eliminated the resonances. The resonances were oriented primarily in the direction normal to the diaphragm.

  11. Structural stiffness and Coulomb damping in compliant foil journal bearings: Theoretical considerations

    Ku, C.-P. Roger; Heshmat, Hooshang

    1994-07-01

    Compliant foil bearings operate on either gas or liquid, which makes them very attractive for use in extreme environments such as in high-temperature aircraft turbine engines and cryogenic turbopumps. However, a lack of analytical models to predict the dynamic characteristics of foil bearings forces the bearing designer to rely on prototype testing, which is time-consuming and expensive. In this paper, the authors present a theoretical model to predict the structural stiffness and damping coefficients of the bump foil strip in a journal bearing or damper. Stiffness is calculated based on the perturbation of the journal center with respect to its static equilibrium position. The equivalent viscous damping coefficients are determined based on the area of a closed hysteresis loop of the journal center motion. The authors found, theoretically, that the energy dissipated from this loop was mostly contributed by the frictional motion between contact surfaces. In addition, the source and mechanism of the nonlinear behavior of the bump foil strips were examined. With the introduction of this enhanced model, the analytical tools are now available for the design of compliant foil bearings.

  12. Feasibility of Applying Controllable Lubrication to Dynamically Loaded Journal Bearings

    Estupinan, Edgar Alberto; Santos, Ilmar

    2009-01-01

    A multibody dynamic model of the main mechanical components of a hermetic reciprocating compressor is presented in this work. Considering that some of the mechanical elements are interconnected via thin fluid films, the multibody dynamic model is coupled to the equations from the dynamics...... of the fluid films, based on fluid film theory. For a dynamically loaded journal bearing, the fluid film pressure distribution can be computed by numerically solving the Reynolds equation, by means of finite-difference method. Particularly, in this study the main focus is on the lubrication behavior...... and reaction forces in a reciprocating compressor have a cyclic behavior, periodic oil pressure injection rules based on the instantaneous crank angle and load bearing condition can be established. In this paper, several bearing configurations working under different oil pressure injection rules conditions...

  13. Active control of multi-input hydraulic journal bearing system

    Chuang, Jen-Chen; Chen, Chi-Yin; Tu, Jia-Ying

    2016-09-01

    Because of the advantages of high accuracy, high capacity, and low friction, the development of hydrostatic bearing for machine tool receives significant attention in the last decades. The mechanics and mechanical design of hydrostatic journal bearing with capillary restrictors has been discussed in literature. However, pragmatically, the undesired loading effects of cutting force tend to result in resonance and instability of the rotor and damage the shaft during operation. Therefore, multi-input, active flow control using state feedback design is proposed in this paper. To this purpose, the proportional pressure valves are added to the hydraulic system as active control devices, and the linearised models of the bearing and valve are discussed and identified. Simulation and experimental work is conducted to verify the proposed active control and parameter identification techniques. The results show that the unbalance responses of the rotor are reduced by the proposed state feedback controller, which is able to regulate the flow pressure effectively, thus enhancing the stability and accuracy of the hydraulic journal bearing.

  14. 49 CFR 215.109 - Defective plain bearing box: Journal lubrication system.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective plain bearing box: Journal lubrication... Freight Car Components Suspension System § 215.109 Defective plain bearing box: Journal lubrication system...) Metal parts contacting the journal; or (e) Is— (1) Missing; or (2) Not in contact with the journal. ...

  15. Investigation of journal orbit and flow pattern in a dynamically loaded journal bearing

    Christiansen, Christian Kim; Walther, Jens Honore; Klit, Peder

    2017-01-01

    A hydrodynamic journal bearing has been investigated using both the traditional two-dimensional (2D) Reynolds equation, and the full solution being the three-dimensional (3D) Navier-Stokes equations. The two approaches are compared by performing an investigation of two inlet groove designs: the a...

  16. Study on the prevention of spragging in a tilting pad journal bearing using the variation of preload

    Yang, Seong Heon; Park, Chul Hyun; Ha, Hyun Cheon; Kim, Chae Sil

    2001-01-01

    Tilting pad journal bearings have been widely used in a high speed rotating machinery, such as steam turbines and gas turbines, owing to their inherent stability characteristics. However, some peculiar fatigue failure in the babbitt metal due to spragging has been continuously occurred at the leading edge of the upper pads. The spragging is defined as the pad vibration initiated on the upper unloaded pads in tilting pad journal bearing. This paper describes both several kinds of bearing failure related with spragging and the theoretical investigation on the prevention of the spragging phenomenon using the variation of preload. Results show that positive preload(m>0.5) assures all pads remain statically loaded under all operating conditions. For the change of design parameter to prevent spragging, thermo-hydrodynamic lubrication and rotor dynamic analysis were performed to verify temperature limitation on bearing and vibration problems on rotor bearing system

  17. Numerical Investigation of Turbulence Models for a Superlaminar Journal Bearing

    Aoshuang Ding

    2018-01-01

    Full Text Available With rotating machineries working at high speeds, oil flow in bearings becomes superlaminar. Under superlaminar conditions, flow exhibits between laminar and fully developed turbulence. In this study, superlaminar oil flow in an oil-lubricated tilting-pad journal bearing is analyzed through computational fluid dynamics (CFD. A three-dimensional bearing model is established. CFD results from the laminar model and 14 turbulence models are compared with experimental findings. The laminar simulation results of pad-side pressure are inconsistent with the experimental data. Thus, the turbulence effects on superlaminar flow should be considered. The simulated temperature and pressure distributions from the classical fully developed turbulence models cannot correctly fit the experimental data. As such, turbulence models should be corrected for superlaminar flow. However, several corrections, such as transition correction, are unsuitable. Among all the flow models, the SST model with low-Re correction exhibits the best pressure distribution and turbulence viscosity ratio. Velocity profile analysis confirms that a buffer layer plays an important role in the superlaminar boundary layer. Classical fully developed turbulence models cannot accurately predict the buffer layer, but this problem can be resolved by initiating an appropriate low-Re correction. Therefore, the SST model with low-Re correction yields suitable results for superlaminar flows in bearings.

  18. Maintenance free gas bearing helium blower for nuclear plant

    Molyneaux, A., Dr; Harris, M., Prof; Sharkh, S., Prof; Hill, S.; de Graaff, T.

    2017-08-01

    This paper describes the design, testing and operation of novel helium blowers used to recirculate the helium blanketing gas in the nuclear reactor used as a neutron source at the Institut Laue Langevan, Grenoble, France. The laser sintered shrouded centrifugal wheel operates at speeds up to 45000 rpm supported on helium lubricated hydrodynamic spiral groove bearings, and is driven by a sensorless permanent magnet motor. The entire machine is designed to keep the helium gas (polluted by a small amount of D2O) out of contact with any iron or copper materials which would contribute to the corrosion of parts of the circuit. It is designed to have zero maintenance during a lifetime of 40,000 hours of continuous operation. This paper will describe the spiral groove journal and thrust bearings. Design and manufacture of the 1 kW motor and centrifugal wheel will be explained including their CFD and FEA analyses. Measurements of rotor displacement will be presented showing the behaviour under factory testing as well as details of the measured centrifugal wheel and motor performances. Two machines are incorporated into the circuit to provide redundancy and the first blower has been in continuous operation since Jan 2015. The blower was designed, manufactured, assembled and tested in the UK using predominantly UK suppliers.

  19. Piezoelectric actuators in the active vibration control system of journal bearings

    Tůma, J.; Šimek, J.; Mahdal, M.; Pawlenka, M.; Wagnerova, R.

    2017-07-01

    The advantage of journal hydrodynamic bearings is high radial load capacity and operation at high speeds. The disadvantage is the excitation of vibrations, called an oil whirl, after crossing a certain threshold of the rotational speed. The mentioned vibrations can be suppressed using the system of the active vibration control with piezoactuators which move the bearing bushing. The motion of the bearing bushing is controlled by a feedback controller, which responds to the change in position of the bearing journal which is sensed by a pair of capacitive sensors. Two stacked linear piezoactuators are used to actuate the position of the bearing journal. This new bearing enables not only to damp vibrations but also serves to maintain the desired bearing journal position with an accuracy of micrometers. The paper will focus on the effect of active vibration control on the performance characteristics of the journal bearing.

  20. Study the Dynamic Behavior of Rotor Supported on a Worn Journal Bearings

    Adnan Naji Jamil

    2015-12-01

    Full Text Available In this paper, the effect of wear in the fluid film journal bearings on the dynamic behavior of rotor bearing system has been studied depending on the analytical driven of dynamic stiffness and damping coefficients of worn journal bearing. The finite element method was used to modeling rotor bearing system. The unbalance response, critical speed and natural frequency of rotor bearing system have been studied to determine the changes in these parameters due to wear. MATLAB software was used to find the analytical values of dynamic coefficients of journal bearing. The results of rotor mounted on fluid film journal bearings showed that the wear in journal bearing increases the amplitude of unbalance response and decrease critical speed, stability and the natural frequencies.

  1. Stabilizing Gas Bearings In Free-Piston Machines

    Dhar, Manmohan

    1995-01-01

    Gas bearings and clearance seals between pistons and cylinders in free-piston machines designed to reduce undesired dynamic forces and torques on pistons, gas bearings, and cylinders. Circumferential grooves and drain galleries added to piston or cylinder in improved design. Provides stabilization without significant reduction in length of seal, or significant increase in leakage and consequent reduction of efficiency.

  2. Lateral Dynamics of Flexible Rotors Supported by Controllable Gas Bearings Theory & Experiment

    Pierart Vásquez, Fabián Gonzalo; Santos, Ilmar

    2015-01-01

    Active gas bearings might represent a mechatronic answer to the growing industrial need for high performance turbomachinery. In this framework, the paper gives a theoretical and experimental contribution to the improvement of lateral dynamics of rotating machines. The work aims at demonstrating...... theoretically as well as experimentally the feasibility of applying active lubrication to gas journal bearings. The operation principle is to generate active forces by regulating the radial injection of a compressible lubricant (gas) by means of piezoelectric actuators mounted on the back of the bearing sleeve....... The active control principle is built using eddy-current sensor signals to detect the lateral motion of the rotor. A feedback law is used to couple the lateral dynamics of a flexible rotor-bearing system with the pneumatic and dynamic characteristics of a piezoelectric actuated valve system. A proportional...

  3. Modelling of Rotor-gas bearings for Feedback Controller Design

    Theisen, Lukas Roy Svane; Niemann, Hans Henrik

    2014-01-01

    Controllable rotor-gas bearings are popular oering adaptability, high speed operation, low friction and clean operation. Rotor-gas bearings are however highly sensitive to disturbances due to the low friction of the injected gas. These undesirable damping properties call for controllers, which ca...... and are shown to accurately describe the dynamical behaviour of the rotor-gas bearing. Design of a controller using the identied models is treated and experiments verify the improvement of the damping properties of the rotor-gas bearing.......Controllable rotor-gas bearings are popular oering adaptability, high speed operation, low friction and clean operation. Rotor-gas bearings are however highly sensitive to disturbances due to the low friction of the injected gas. These undesirable damping properties call for controllers, which can...... be designed from suitable models describing the relation from actuator input to measured shaft position. Current state of the art models of controllable gas bearings however do not provide such relation, which calls for alternative strategies. The present contribution discusses the challenges for feedback...

  4. Journal Bearing Analysis Suite Released for Planetary Gear System Evaluation

    Brewe, David E.; Clark, David A.

    2005-01-01

    Planetary gear systems are an efficient means of achieving high reduction ratios with minimum space and weight. They are used in helicopter, aerospace, automobile, and many industrial applications. High-speed planetary gear systems will have significant dynamic loading and high heat generation. Hence, they need jet lubrication and associated cooling systems. For units operating in critical applications that necessitate high reliability and long life, that have very large torque loading, and that have downtime costs that are significantly greater than the initial cost, hydrodynamic journal bearings are a must. Computational and analytical tools are needed for sufficiently accurate modeling to facilitate optimal design of these systems. Sufficient physics is needed in the model to facilitate parametric studies of design conditions that enable optimal designs. The first transient journal bearing code to implement the Jacobsson-Floberg-Olsson boundary conditions, using a mass-conserving algorithm devised by Professor Emeritus Harold Elrod of Columbia University, was written by David E. Brewe of the U.S. Army at the NASA Lewis Research Center1 in 1983. Since then, new features and improved modifications have been built into the code by several contributors supported through Army and NASA funding via cooperative agreements with the University of Toledo (Professor Ted Keith, Jr., and Dr. Desikakary Vijayaraghavan) and National Research Council Programs (Dr. Vijayaraghavan). All this was conducted with the close consultation of Professor Elrod and the project management of David Brewe.

  5. Model-Based Control Design for Flexible Rotors Supported by Active Gas Bearings - Theory & Experiment

    Pierart Vásquez, Fabián Gonzalo

    , abundant and clean. Nevertheless, this technology has important drawbacks: the low viscosity of the lubricant results in a low load carrying capacity and gas bearings also presents low damping properties, which often lead to a reduced stability range and make dangerous running close to, or across...... theoretical model for active gas bearings, with special attention to the modelling of the injection system. Secondly, experimentally validate the improved mathematical model in terms of static properties (journal equilibrium position and resulting aerodynamic forces) and dynamic properties (natural...

  6. Analysis of multi lobe journal bearings with surface roughness using finite difference method

    PhaniRaja Kumar, K.; Bhaskar, SUdaya; Manzoor Hussain, M.

    2018-04-01

    Multi lobe journal bearings are used for high operating speeds and high loads in machines. In this paper symmetrical multi lobe journal bearings are analyzed to find out the effect of surface roughnessduring non linear loading. Using the fourth order RungeKutta method, time transient analysis was performed to calculate and plot the journal centre trajectories. Flow factor method is used to evaluate the roughness and the finite difference method (FDM) is used to predict the pressure distribution over the bearing surface. The Transient analysis is done on the multi lobe journal bearings for threedifferent surface roughness orientations. Longitudinal surface roughness is more effective when compared with isotopic and traverse surface roughness.

  7. Lubrication analysis of the journal bearing in the main coolant pump of SMART

    Lee, J. S.; Park, J. S.; Kim, J. H.; Kim, J. I.; Jang, M. H.

    2000-01-01

    Special type journal bearings are installed in the main coolant pump for SMART to support the rotating shaft with proper lubrication. The canned motor type main coolant pumps are arranged vertically on the reactor vessel. The MCP bearings are lubricated with water without external lubricating oil supply. Long bearing with vertical grooves is designed with relatively large bearing clearance to accommodate the long shaft. Lubricational analysis method for journal bearing with vertical grooves in the main coolant pump of SMART is proposed, and lubricational characteristics of the bearings are examined in this paper

  8. Direct Monte Carlo simulation of nanoscale mixed gas bearings

    Kyaw Sett Myo

    2015-06-01

    Full Text Available The conception of sealed hard drives with helium gas mixture has been recently suggested over the current hard drives for achieving higher reliability and less position error. Therefore, it is important to understand the effects of different helium gas mixtures on the slider bearing characteristics in the head–disk interface. In this article, the helium/air and helium/argon gas mixtures are applied as the working fluids and their effects on the bearing characteristics are studied using the direct simulation Monte Carlo method. Based on direct simulation Monte Carlo simulations, the physical properties of these gas mixtures such as mean free path and dynamic viscosity are achieved and compared with those obtained from theoretical models. It is observed that both results are comparable. Using these gas mixture properties, the bearing pressure distributions are calculated under different fractions of helium with conventional molecular gas lubrication models. The outcomes reveal that the molecular gas lubrication results could have relatively good agreement with those of direct simulation Monte Carlo simulations, especially for pure air, helium, or argon gas cases. For gas mixtures, the bearing pressures predicted by molecular gas lubrication model are slightly larger than those from direct simulation Monte Carlo simulation.

  9. Performance of an Orifice Compensated Two-Lobe Hole-Entry Hybrid Journal Bearing

    J. Sharana Basavaraja

    2008-01-01

    Full Text Available The work presented in this paper aims to study the performance of a two-lobe hole-entry hybrid journal bearing system compensated by orifice restrictors. The Reynolds equation governing the flow of lubricant in the clearance space between the journal and bearing together with the equation of flow through an orifice restrictor has been solved using FEM and Galerkin's method. The bearing performance characteristics results have been simulated for an orifice compensated nonrecessed two-lobe hole-entry hybrid journal bearing symmetric configuration for the various values of offset factor (, restrictor design parameter (2, and the value of external load (0. Further, a comparative study of the performance of a two-lobe hole-entry hybrid journal bearing system with a circular hole-entry symmetric hybrid journal bearing system has also been carried out so that a designer has a better flexibility in choosing a suitable bearing configuration. The simulated numerical results indicate that for the two-lobe symmetric hole-entry hybrid journal bearing system with an offset factor ( greater than one provides 30 to 50 percent larger values of direct stiffness and direct damping coefficients as compared to a circular symmetric hole-entry hybrid journal bearing system.

  10. Modelling and Identification for Control of Gas Bearings

    Theisen, Lukas Roy Svane; Niemann, Hans Henrik; Santos, Ilmar

    2015-01-01

    Gas bearings are popular for their high speed capabilities, low friction and clean operation, but suffer from poor damping, which poses challenges for safe operation in presence of disturbances. Enhanced damping can be achieved through active lubrication techniques using feedback control laws....... Such control design requires models with low complexity, able to describe the dominant dynamics from actuator input to sensor output over the relevant range of operation. The mathematical models based on first principles are not easy to obtain, and in many cases, they cannot be directly used for control design...... to industrial rotating machinery with gas bearings and to allow for subsequent control design. The paper shows how piezoelectric actuators in a gas bearing are efficiently used to perturb the gas film for identification over relevant ranges of rotational speed and gas injection pressure. Parameter...

  11. Evaluation of datum unit for diagnostics of journal-bearing systems

    Jeon, Byung Chul; Jung, Joon Ha; Youn, Byeng Doog; Kim, Yeon Whan; Bae, Yong Chae

    2015-01-01

    Journal bearings support rotors using fluid film between the rotor and the stator. Generally, journal bearings are used in large rotor systems such as turbines in a power plant, because even in high-speed and load conditions, journal bearing systems run in a stable condition. To enhance the reliability of journal-bearing systems, in this paper, we study health-diagnosis algorithms that are based on the supervised learning method. Specifically, this paper focused on defining the unit of features, while other previous papers have focused on defining various features of vibration signals. We evaluate the features of various lengths or units on the separable ability basis. From our results, we find that one cycle datum in the time-domain and 60 cycle datum in the frequency domain are the optimal datum units for real-time journal-bearing diagnosis systems

  12. Evaluation of datum unit for diagnostics of journal-bearing systems

    Jeon, Byung Chul; Jung, Joon Ha; Youn, Byeng Doog [Dept. of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Kim, Yeon Whan; Bae, Yong Chae [Power Generation Laboratory, KEPCO Research Institute, Daejeon (Korea, Republic of)

    2015-08-15

    Journal bearings support rotors using fluid film between the rotor and the stator. Generally, journal bearings are used in large rotor systems such as turbines in a power plant, because even in high-speed and load conditions, journal bearing systems run in a stable condition. To enhance the reliability of journal-bearing systems, in this paper, we study health-diagnosis algorithms that are based on the supervised learning method. Specifically, this paper focused on defining the unit of features, while other previous papers have focused on defining various features of vibration signals. We evaluate the features of various lengths or units on the separable ability basis. From our results, we find that one cycle datum in the time-domain and 60 cycle datum in the frequency domain are the optimal datum units for real-time journal-bearing diagnosis systems.

  13. Exploring integral controllers in actively-lubricated tilting-pad journal bearings

    Salazar, Jorge Andrés González; Santos, Ilmar

    2015-01-01

    investigation of integral controllers for feedback-controlled lubrication with the aim of: a) presetting the static journal center and consequently exploring the changes of bearing dynamic properties; b) obtaining an integral controller capable of re-positioning the static journal eccentricity for matching......Active tilting-pad journal bearings with radial oil injection combine good stability properties of conventional tilting-pad journal bearings with the capability of improving their dynamic properties even more by control techniques. The main contribution of this work is the experimental...

  14. Experimental investigation of gas aerostatic bearings

    Steinbauer, P.; Šika, Z.; Kozánek, Jan; Šimek, J.

    2008-01-01

    Roč. 3, - (2008), s. 769-776 ISSN 1335-2393 R&D Projects: GA ČR GA101/06/1787 Institutional research plan: CEZ:AV0Z20760514 Keywords : aerostatic bearing * experimental identification * measurement Subject RIV: BI - Acoustics

  15. Numerical analysis of capillary compensated micropolar fluid lubricated hole-entry journal bearings

    Nathi Ram

    2016-06-01

    Full Text Available The micropolar lubricated symmetric/asymmetric hole-entry bearings using capillary restrictor have been analyzed in the present work. Reynolds equation for micropolar lubricant has been derived and solved by FEM. The results have been computed using selected parameters of micropolar lubricant for hole-entry hydrostatic/hybrid journal bearings. A significant increase in damping and stiffness coefficients is observed for bearings having micropolar parameter N2=0.9, lm=10 than similar bearings under Newtonian lubricant. The threshold speed gets increased when symmetric bearing lubricated under micropolar fluid than Newtonian lubricant. The threshold speed gets increased when symmetric bearing lubricated under micropolar fluid than Newtonian lubricant.

  16. Auxiliary bearing design considerations for gas cooled reactors

    Penfield, S.R. Jr.; Rodwell, E.

    2001-01-01

    The need to avoid contamination of the primary system, along with other perceived advantages, has led to the selection of electromagnetic bearings (EMBs) in most ongoing commercial-scale gas cooled reactor (GCR) designs. However, one implication of magnetic bearings is the requirement to provide backup support to mitigate the effects of failures or overload conditions. The demands on these auxiliary or 'catcher' bearings have been substantially escalated by the recent development of direct Brayton cycle GCR concepts. Conversely, there has been only limited directed research in the area of auxiliary bearings, particularly for vertically oriented turbomachines. This paper explores the current state-of-the-art for auxiliary bearings and the implications for current GCR designs. (author)

  17. Bifurcation analysis of an aerodynamic journal bearing system considering the effect of stationary herringbone grooves

    Wang, C.-C.

    2007-01-01

    This paper investigates the bifurcation and nonlinear behavior of an aerodynamic journal bearing system taking into account the effect of stationary herringbone grooves. A finite difference method based on the successive over relation approach is employed to solve the Reynolds' equation. The analysis reveals a complex dynamical behavior comprising periodic and quasi-periodic responses of the rotor center. The dynamic behavior of the bearing system varies with changes in the bearing number and rotor mass. The results of this study provide a better understanding of the nonlinear dynamics of aerodynamic grooved journal bearing systems

  18. The Effect of Non-Circular Bearing Shapes in Hydrodynamic Journal Bearings on the Vibration Behavior of Turbocharger Structures

    Lukas Bernhauser

    2017-03-01

    Full Text Available Increasing quality demands of combustion engines require, amongst others, improvements of the engine’s acoustics and all (subcomponents mounted to the latter. A significant impact to the audible tonal noise spectrum results from the vibratory motions of fast-rotating turbocharger rotor systems in multiple hydrodynamic bearings such as floating bearing rings. Particularly, the study of self-excited non-linear vibrations of the rotor-bearing systems is crucial for the understanding, prevention or reduction of the noise and, consequently, for a sustainable engine acoustics development. This work presents an efficient modeling approach for the investigation, optimization, and design improvement of complex turbocharger rotors in hydrodynamic journal bearings, including floating bearing rings with circular and non-circular bearing geometries. The capability of tonal non-synchronous vibration prevention using non-circular bearing shapes is demonstrated with dynamic run-up simulations of the presented model. These findings and the performance of our model are compared and validated with results of a classical Laval/Jeffcott rotor-bearing model and a specific turbocharger model found in the literature. It is shown that the presented simulation method yields fast and accurate results and furthermore, that non-circular bearing shapes are an effective measure to reduce or even prevent self-excited tonal noise.

  19. Measured displacement coefficients of an adjustable hydrodynamic journal rotor bearing

    Martin, J. K.

    2013-01-01

    In simulating a proposed machine tool grinding wheel design, a bearing system comprised a stationary spindle or shaft with fluid film bearings supporting a belt driven rotor. Two hydrodynamic bearings acted in parallel, and built into the shaft were the means to effect continuous pro-active adjustments to their performance characteristics during operation, irrespective of load, speed and other running conditions. The design is outlined, as is a specially constructed test rig for evaluating it...

  20. On the simplifications for the thermal modeling of tilting-pad journal bearings under thermoelastohydrodynamic regime

    Cerda Varela, Alejandro Javier; Fillon, Michel; Santos, Ilmar

    2012-01-01

    formulation for inclusion of the heat transfer effects between oil film and pad surface. Such simplified approach becomes necessary when modeling the behavior of tilting-pad journal bearings operating on controllable lubrication regime. Three different simplified heat transfer models are tested, by comparing...... are strongly dependent on the Reynolds number for the oil flow in the bearing. For bearings operating in laminar regime, the decoupling of the oil film energy equation solving procedure, with no heat transfer terms included, with the pad heat conduction problem, where the oil film temperature is applied......The relevance of calculating accurately the oil film temperature build up when modeling tilting-pad journal bearings is well established within the literature on the subject. This work studies the feasibility of using a thermal model for the tilting-pad journal bearing which includes a simplified...

  1. Prevention of Roller Bearing-Initiated Burnoffs in Railroad Freight Car Journals

    1979-01-01

    The objective of this program was to determine the technical feasibility and cost effectiveness of constructing three separate devices for the prevention of catastrophic roller bearing-initiated, railroad journal failure. 1. Construction of a low cos...

  2. A study of the transient performance of hydrostatic journal bearings. I - Test apparatus and facility

    Scharrer, J. K.; Tellier, J.; Hibbs, R.

    1992-10-01

    A test apparatus was developed for studies of the transient performance of hydrostatic journal bearings operating in liquid nitrogen. The data obtained give the number of revolutions of the shaft contact before the liftoff and after touchdown as a function of bearing/shaft material combinations and operating conditions.

  3. Performance Improvement of tilting-pad journal bearings by means of controllable lubrication

    Cerda, Alejandro; Santos, Ilmar

    2012-01-01

    Tilting-Pad Journal Bearings (TPJB) are commonly used on high-performance turbomachinery due to their excellent stability properties at high speed when compared to other designs for oil film bearings. Hence, efforts have been made to improve the accuracy for the available models for these mechani...... is used to show the benefits of applying a controllable lubrication regime, by means of the modification of the thermal and dynamic behaviour of the bearing....

  4. Soil cover of gas-bearing areas

    Mozharova, N. V.

    2010-08-01

    Natural soils with disturbed functioning parameters compared to the background soils with conservative technogenic-pedogenic features were distinguished on vast areas above the artificial underground gas storages in the zones of spreading and predominant impact of hydrocarbon gases. The disturbance of the functioning parameters is related to the increase in the methane concentration, the bacterial oxidation intensity and destruction, and the complex microbiological and physicochemical synthesis of iron oxides. The technogenic-pedogenic features include neoformations of bacteriomorphic microdispersed iron oxides. The impurity components consist of elements typical for biogenic structures. New soil layers, horizons, specific anthropogenically modified soils, and soil-like structures were formed on small areas in the industrial zones of underground gas storages due to the mechanical disturbance, the deposition of drilling sludge, and the chemical contamination. Among the soils, postlithogenic formations were identified—chemotechnosols (soddy-podzolic soils and chernozems), as well as synlithogenic ones: strato-chemotechnosols and stratochemoembryozems. The soil-like bodies included postlithogenic soil-like structures (chemotechnozems) and synlithogenic ones (strato-chemotechnozems). A substantive approach was used for the soil diagnostics. The morphological and magnetic profiles and the physical, chemical, and physicochemical properties of the soils were analyzed. The micromorphological composition of the soil magnetic fraction was used as a magnetic label.

  5. Active vibrations control of journal bearings with the use of piezoactuators

    Tůma, Jiří; Šimek, Jiří; Škuta, Jaromír; Los, Jaroslav

    2013-04-01

    Rotor instability is one of the most serious problems of high-speed rotors supported by sliding bearings. With constantly increasing parameters, new machines problems with rotor instability are encountered more and more often. Even though there are many solutions based on passive improvement of the bearing geometry to enlarge the operational speed range of the journal bearing, the paper deals with a working prototype of a system for the active vibration control of journal bearings with the use of piezoactuators. The controllable journal bearing is a part of a test rig, which consists of a rotor driven by an inductive motor up to 23,000 rpm. The actively controlled journal bearing consists of a movable bushing, which is actuated by two piezoactuators. The journal vibration is measured by a pair of proximity probes. The control system enables run-up, coast-down and steady-state rotation. A real-time simulator dSpace encloses the control loop. Force produced by piezoactuators and acting at the bushing is controlled according to error signals derived from the proximity probe output signals. As it was proved by experiments the active vibration control extends considerably the range of the operational speed.

  6. CFD Analysis of A Starved Four-Pad Tilting-Pad Journal Bearing with An Elastic Support of Pads

    Parovay, E. F.; Falaleev, S. V.

    2018-01-01

    Tilting-pad journal bearings are widely used in technics. Oil starvation operation regime is not common for hydrodynamic bearings. However, correctly designed low-flow journal bearing have to operate efficiently and consistently on high rotor speeds. An elastic support of bearing pads is a set of elastic pins made of steel. Elastic support allows pads to self-align and achieve an optimal operational mode. The article presents the thermohydrodynamic performance of an axial journal bearing. The study deals with 60 mm diameter four-pad tilting-pad journal bearing, submitted to a static load varying from 1000 to 30000 N with a rotating speed varying from 1000 to 10000 rpm. The investigation focuses on numerical studying the characteristics of low-flow tilting-pad journal bearings under oil starvation conditions. Dependencies of the bearing performance on the load, rotational speed of the shaft, and the size of the radial clearance are presented.

  7. Study of journal bearing dynamics using 3-dimensional motion picture graphics

    Brewe, D. E.; Sosoka, D. J.

    1985-01-01

    Computer generated motion pictures of three dimensional graphics are being used to analyze journal bearings under dynamically loaded conditions. The motion pictures simultaneously present the motion of the journal and the pressures predicted within the fluid film of the bearing as they evolve in time. The correct prediction of these fluid film pressures can be complicated by the development of cavitation within the fluid. The numerical model that is used predicts the formation of the cavitation bubble and its growth, downstream movement, and subsequent collapse. A complete physical picture is created in the motion picture as the journal traverses through the entire dynamic cycle.

  8. A superlinear iteration method for calculation of finite length journal bearing's static equilibrium position

    Zhou, Wenjie; Wei, Xuesong; Wang, Leqin; Wu, Guangkuan

    2017-05-01

    Solving the static equilibrium position is one of the most important parts of dynamic coefficients calculation and further coupled calculation of rotor system. The main contribution of this study is testing the superlinear iteration convergence method-twofold secant method, for the determination of the static equilibrium position of journal bearing with finite length. Essentially, the Reynolds equation for stable motion is solved by the finite difference method and the inner pressure is obtained by the successive over-relaxation iterative method reinforced by the compound Simpson quadrature formula. The accuracy and efficiency of the twofold secant method are higher in comparison with the secant method and dichotomy. The total number of iterative steps required for the twofold secant method are about one-third of the secant method and less than one-eighth of dichotomy for the same equilibrium position. The calculations for equilibrium position and pressure distribution for different bearing length, clearance and rotating speed were done. In the results, the eccentricity presents linear inverse proportional relationship to the attitude angle. The influence of the bearing length, clearance and bearing radius on the load-carrying capacity was also investigated. The results illustrate that larger bearing length, larger radius and smaller clearance are good for the load-carrying capacity of journal bearing. The application of the twofold secant method can greatly reduce the computational time for calculation of the dynamic coefficients and dynamic characteristics of rotor-bearing system with a journal bearing of finite length.

  9. Steady state characteristics of an adjustable hybrid gas bearing – Computational fluid dynamics, modified Reynolds equation and experimental validation

    Pierart Vásquez, Fabián Gonzalo; Santos, Ilmar

    2015-01-01

    To include the effect of external pressurization in hybrid gas bearings an extra term is added to Reynolds Equation to accommodate the gas jet. Two cases are considered: cylindrical and annular flow profiles. Validation of theoretical results obtained using the modified version of Reynolds equation....... By introducing such coefficients into the modified Reynolds equation, good agreement with experiments is achieved in terms of journal equilibrium position and resulting aerodynamic forces....

  10. Maximum Recoverable Gas from Hydrate Bearing Sediments by Depressurization

    Terzariol, Marco

    2017-11-13

    The estimation of gas production rates from hydrate bearing sediments requires complex numerical simulations. This manuscript presents a set of simple and robust analytical solutions to estimate the maximum depressurization-driven recoverable gas. These limiting-equilibrium solutions are established when the dissociation front reaches steady state conditions and ceases to expand further. Analytical solutions show the relevance of (1) relative permeabilities between the hydrate free sediment, the hydrate bearing sediment, and the aquitard layers, and (2) the extent of depressurization in terms of the fluid pressures at the well, at the phase boundary, and in the far field. Close form solutions for the size of the produced zone allow for expeditious financial analyses; results highlight the need for innovative production strategies in order to make hydrate accumulations an economically-viable energy resource. Horizontal directional drilling and multi-wellpoint seafloor dewatering installations may lead to advantageous production strategies in shallow seafloor reservoirs.

  11. Experimental contribution to the study of gas bearings

    Gobert, G.

    1962-01-01

    Developments for gas-lubricated bearings are discussed. The study of how the fluid film behaves compared to what one can expect is discussed. Various devices are described which have allowed us to go up to peripheral velocity greater than 400 m/s, leading to rotational speed of several thousand revolutions per second. This is obtained by using an automatic setting for the distance between fixed and rotating walls. (author) [fr

  12. Stress Analysis and Fatigue Behaviour of PTFE-Bronze Layered Journal Bearing under Real-Time Dynamic Loading

    Duman, M. S.; Kaplan, E.; Cuvalcı, O.

    2018-01-01

    The present paper is based on experimental studies and numerical simulations on the surface fatigue failure of the PTFE-bronze layered journal bearings under real-time loading. ‘Permaglide Plain Bearings P10’ type journal bearings were experimentally tested under different real time dynamic loadings by using real time journal bearing test system in our laboratory. The journal bearing consists of a PTFE-bronze layer approximately 0.32 mm thick on the steel support layer with 2.18 mm thick. Two different approaches have been considered with in experiments: (i) under real- time constant loading with varying bearing widths, (ii) under different real-time loadings at constant bearing widths. Fatigue regions, micro-crack dispersion and stress distributions occurred at the journal bearing were experimentally and theoretically investigated. The relation between fatigue region and pressure distributions were investigated by determining the circumferential pressure distribution under real-time dynamic loadings for the position of every 10° crank angles. In the theoretical part; stress and deformation distributions at the surface of the journal bearing analysed by using finite element methods to determine the relationship between stress and fatigue behaviour. As a result of this study, the maximum oil pressure and fatigue cracks were observed in the most heavily loaded regions of the bearing surface. Experimental results show that PTFE-Bronze layered journal bearings fatigue behaviour is better than the bearings include white metal alloy.

  13. Establishment of Approximate Analytical Model of Oil Film Force for Finite Length Tilting Pad Journal Bearings

    Yongliang Wang

    2015-01-01

    Full Text Available Tilting pad bearings offer unique dynamic stability enabling successful deployment of high-speed rotating machinery. The model of dynamic stiffness, damping, and added mass coefficients is often used for rotordynamic analyses, and this method does not suffice to describe the dynamic behaviour due to the nonlinear effects of oil film force under larger shaft vibration or vertical rotor conditions. The objective of this paper is to present a nonlinear oil force model for finite length tilting pad journal bearings. An approximate analytic oil film force model was established by analysing the dynamic characteristic of oil film of a single pad journal bearing using variable separation method under the dynamic π oil film boundary condition. And an oil film force model of a four-tilting-pad journal bearing was established by using the pad assembly technique and considering pad tilting angle. The validity of the model established was proved by analyzing the distribution of oil film pressure and the locus of journal centre for tilting pad journal bearings and by comparing the model established in this paper with the model established using finite difference method.

  14. Experimental Estimation of Journal Bearing Stiffness for Damage Detection in Large Hydrogenerators

    Geraldo Carvalho Brito

    2017-01-01

    Full Text Available Based on experimental pieces of evidence collected in a set of twenty healthy large hydrogenerators, this article shows that the operating conditions of the tilting pad journal bearings of these machines may have unpredictable and significant changes. This behavior prevents the theoretical determination of bearing stiffness and damping coefficients with an adequate accuracy and makes damage detection difficult. Considering that dynamic coefficients have similar sensitivity to damage and considering that it is easier to monitor bearing stiffness than bearing damping, this article discusses a method to estimate experimentally the effective stiffness coefficients of hydrogenerators journal bearings, using only the usually monitored vibrations, with damage detection purposes. Validated using vibration signals synthesized by a simplified mathematical model that simulates the dynamic behavior of large hydrogenerators, the method was applied to a journal bearing of a 700 MW hydrogenerator, using two different excitations, the generator rotor unbalance and the vortices formed in the turbine rotor when this machine operates at partial loads. The experimental bearing stiffnesses obtained using both excitations were similar, but they were also much lower than the theoretical predictions. The article briefly discusses the causes of these discrepancies, the method’s uncertainties, and the possible improvements in its application.

  15. Modal interaction and vibration suppression in industrial turbines using adjustable journal bearings

    Chasalevris, Athanasios; Dohnal, Fadi

    2016-09-01

    The vibration suppression by deliberately introducing a parametric excitation in the fluid-film bearings is investigated for an industrial turbine rotor system. A journal bearing with variable adjustable geometry is operated in such a way that the effective stiffness and damping properties vary periodically in time. The proposed bearing is designed for having the ability of changing the bearing fluid film thickness in a semi-active manner. Such an adjustment of the journal bearing properties introduces in the system a time-periodic variation of the effective stiffness and damping properties of the fluid-film. If the time-periodicity is tuned properly to match a parametric anti-resonance, vibration suppression is achieved in the overall system. The paper presents the principle of operation of the recently developed bearings. The simulation of an industrial turbine rotor-bearing shaft line at induced parametric excitation motivates the further development and application of such bearings since the vibration amplitudes are considerably decreased in critical speeds.

  16. Discontinuity effects in dynamically loaded tilting pad journal bearings

    Thomsen, Kim; Klit, Peder; Vølund, Anders

    2011-01-01

    This paper describes two discontinuity effects that can occur when modelling radial tilting pad bearings subjected to high dynamic loads. The first effect to be treated is a pressure build-up discontinuity effect. The second effect is a contact-related discontinuity that disappears when a contact...... force is included in the theoretical model. Methods for avoiding the pressure build-up discontinuity effect are proposed....

  17. Evaluation of journal bearings characteristics using finite element ...

    Journal of Modeling, Design and Management of Engineering Systems ... influence on rotating machine operating and stability. Indeed ... such machines may cause not only high level of noise but also wearing of ... Results are compared with those obtained by an alternative method and show good ... HOW TO USE AJOL.

  18. Active vibration reduction of rigid rotor by kinematic excitation of bushes of journal bearings

    J. Ondrouch

    2010-04-01

    Full Text Available Possibilities of active lateral vibration reduction of a symmetric, rigid rotor supported by journal bearings are given. They were obtained by computational modelling. Efficiency of the feedback P and PD controllers in the stable revolution interval was examined. The linearized rotor system model was used. The results of the theoretical analysis are assigned for a testing stand where the bearing bush motions are deactivated by piezoelectric actuators connected to the controllers.

  19. Cascading Tesla Oscillating Flow Diode for Stirling Engine Gas Bearings

    Dyson, Rodger

    2012-01-01

    Replacing the mechanical check-valve in a Stirling engine with a micromachined, non-moving-part flow diode eliminates moving parts and reduces the risk of microparticle clogging. At very small scales, helium gas has sufficient mass momentum that it can act as a flow controller in a similar way as a transistor can redirect electrical signals with a smaller bias signal. The innovation here forces helium gas to flow in predominantly one direction by offering a clear, straight-path microchannel in one direction of flow, but then through a sophisticated geometry, the reversed flow is forced through a tortuous path. This redirection is achieved by using microfluid channel flow to force the much larger main flow into this tortuous path. While microdiodes have been developed in the past, this innovation cascades Tesla diodes to create a much higher pressure in the gas bearing supply plenum. In addition, the special shape of the leaves captures loose particles that would otherwise clog the microchannel of the gas bearing pads.

  20. A journal bearing with variable geometry for the suppression of vibrations in rotating shafts: Simulation, design, construction and experiment

    Chasalevris, Athanasios; Dohnal, Fadi

    2015-02-01

    The idea for a journal bearing with variable geometry was formerly developed and investigated on its principles of operation giving very optimistic theoretical results for the vibration quenching of simple and more complicated rotor bearing systems during the passage through the first critical speed. The journal bearing with variable geometry is presented in this paper in its final form with the detailed design procedure. The current journal bearing was constructed in order to be applied in a simple real rotor bearing system that already exists as an experimental facility. The current paper presents details on the manufactured prototype bearing as an experimental continuation of previous works that presented the simulation of the operating principle of this journal bearing. The design parameters are discussed thoroughly under the numerical simulation for the fluid film pressure in dependency of the variable fluid film thickness during the operation conditions. The implementation of the variable geometry bearing in an experimental rotor bearing system is outlined. Various measurements highlight the efficiency of the proposed bearing element in vibration quenching during the passage through resonance. The inspiration for the current idea is based on the fact that the alteration of the fluid film characteristics of stiffness and damping during the passage through resonance results in vibration quenching. This alteration of the bearing characteristics is achieved by the introduction of an additional fluid film thickness using the passive displacement of the lower half-bearing part. • The contribution of the current journal bearing in vibration quenching. • Experimental evidence for the VGJB contribution.

  1. Dynamic Stability Analysis and Critical Speed of Rotor supported by a Worn Fluid film Journal Bearings

    Adnan naji jameel

    2016-03-01

    Full Text Available In this paper, the effect of wear in the fluid film journal bearings on the dynamic stability of rotor bearing system has been studied depending on the development of new analytical equations for motion, instability threshold speed and steady state harmonic response for rotor with offset disc supported by worn journal bearings. Finite element method had been used for modeling the rotor bearing system. The analytical model is verified by comparing its results with that obtained numerically for a rotor supported on the short bearings. The analytical and numerical results showed good agreement with about 8.5% percentage error in the value of critical speed and about 3.5% percentage error in the value of harmonic response. The results obtained show that the wear in journal bearing decrease the instability threshold speed by 2.5% for wear depth 0.02 mm and 12.5% for wear depth 0.04 mm as well as decrease critical speed by 4.2% and steady state harmonic response amplitude by 4.3% for wear depth 0.02 mm and decrease the critical speed by 7.1% and steady state harmonic response amplitude by 13.9% for wear depth 0.04 mm.

  2. Analysis of Nanoparticle Additive Couple Stress Fluids in Three-layered Journal Bearing

    Rao, T V V L N; Sufian, S; Mohamed, N M

    2013-01-01

    The present theoretical study investigates the load capacity and friction coefficient in a three-layered journal bearing lubricated with nanoparticle additive couple stress fluids. The couple stresses effects are analyzed based on Stokes micro-continuum theory. The nondimensional pressure and shear stress expressions are derived using modified Reynolds equation. The nondimensional load capacity increases and the coefficient of friction decreases using nanoparticle additive lubricants with couple stress effects. The three-layered journal bearing performance characteristics are improved with increase in both (i) surface adsorbent fluid film layer thickness and (ii) dynamic viscosity ratio of surface to core layer.

  3. Tilting-Pad Journal Bearings with Active Lubrication Applied as Calibrated Shakers: Theory and Experiment

    Cerda Varela, Alejandro Javier; Santos, Ilmar

    2014-01-01

    In recent years, a continuous research effort has transformed the conventional tilting-pad journal bearing into a mechatronic machine element. The addition of electromechanical elements provides the possibility of generating controllable forces over the rotor as a function of a suitable control...... directly into the bearing clearance. The injected flow is controlled by means of a servovalve. The theoretical model includes the dynamics of servovalves and pipelines using a lumped parameter approach, whereas the coupling between the hydraulic system and the bearing oil film is modeled using a modified...

  4. A study of the transient performance of annular hydrostatic journal bearings in liquid oxygen

    Scharrer, J. K.; Tellier, J. G.; Hibbs, R. I.

    1992-07-01

    A test apparatus was used to simulate a cryogenic turbopump start transient in order to determine the liftoff and touchdown speed and amount of wear of an annular hydrostatic bearing in liquid oxygen. The bearing was made of sterling silver and the journal made of Inconel 718. The target application of this configuration is the pump end bearing of the Space Shuttle Main Engine High Pressure Liquid Oxygen Turbopump. Sixty-one transient cycles were performed in liquid oxygen with an additional three tests in liquid nitrogen to certify the test facility and configuration. The bearing showed no appreciable wear during the testing, and the results indicate that the performance of the bearing was not significantly degraded during the testing.

  5. Experimental Investigations of Decentralised Control Design for The Stabilisation of Rotor-Gas Bearings

    Theisen, Lukas Roy Svane; Galeazzi, Roberto; Niemann, Hans Henrik

    2015-01-01

    frequencies. Active lubrication of the journal during operations could enhance the damping and stabilisation characteristics of the sytems, and this could be achieved by means of stabilising controllers. This paper investigates the feasibility of using reduced order models obtained through Grey......-Box identification for the design of stabilising controllers, capable of enabling the active lubrication of the journal. The root locus analysis shows that two different control solutions are feasible for the dampening of the first two eigenfrequencies of the rotor-gas bearing in the horizontal and vertical...... directions. Hardening and softening P-lead controllers are designed based on the models experimentally identified, and salient features of both controllers are discussed. Both controllers are implemented and validated on the physical test rig. Experimental results confirm the validity of the proposed...

  6. Hydrodynamic air lubricated compliant surface bearing for an automotive gas turbine engine. 2: Materials and coatings

    Bhushan, B.; Ruscitto, D.; Gray, S.

    1978-01-01

    Material coatings for an air-lubricated, compliant journal bearing for an automotive gas turbine engine were exposed to service test temperatures of 540 C or 650 C for 300 hours, and to 10 temperature cycles from room temperatures to the service test temperatures. Selected coatings were then put on journal and partial-arc foils and tested in start-stop cycle tests at 14 kPa (2 psi) loading for 2000 cycles. Half of the test cycles were performed at a test chamber service temperature of 540 C (1000 F) or 650 C (1200 F); the other half were performed at room temperature. Based on test results, the following combinations and their service temperature limitations are recommended: HL-800 TM (CdO and graphite) on foil versus chrome carbide on journal up to 370 C (700 F); NASA PS 120 (Tribaloy 400, silver and CaF2 on journal versus uncoated foil up to 540 C (1000 F); and Kaman DES on journal and foil up to 640 C (1200 F). Kaman DES coating system was further tested successfully at 35 kPa (5 psi) loading for 2000 start-stop cycles.

  7. Measurement of misalignment in a journal bearing with low frequency ultrasound

    Kim, Noh Nu

    1998-01-01

    Misalignment of a shaft in journal bearing of rotary compressor was measured and analyzed for the study on the effect of misalignment on the performance of the rotary compressor using a new ultrasonic pulse-echo technique. Two low-frequency ultrasonic transducers(10Mhz) were mounted on the outer surface of the bearing in X and Y axis to receive the reflection signals from each axis and to obtain the amplitude of a modified reflection wave defined as the total reflection wave minus the first reflection wave from a thin layer which is inversely proportional to the thickness of the layer in the region where h/λ is approximately less than 1/4. The relationship of the amplitude of the modified reflection wave to the thickness of the oil layer was shown both in mathematical form and in graph. Gap clearances between the bearing and the shaft in the horizontal and vertical axis were determined directly by the relationship and used to evaluate the misalignment of the journal bearing. Several intentional misalignments in a test compressor were made to measure and show the misalignment and the effect of the misalignment on the efficiency of the rotary compressor. A fast quantitative evaluation of the misalignment of journal bearing was possible using the amplitude of the modified reflection signal without any inversion process to extract thickness information from waveforms of the reflected waves.

  8. Evaluation of Oil Film Pressure and Temperature of an Elliptical Journal Bearing - An Experimental Study

    A. Singla

    2016-03-01

    Full Text Available The present study is aimed at experimental evaluation of both oil film pressure and temperature at the central plane of finite elliptical journal bearing configuration. These parameters have been obtained by running the machine at various speeds under different applied loads ranging from 500 N to 2000 N using three different grades of oil (HYDROL 32, 68 and 150. The data has been obtained through a test rig which is capable of measuring both pressure and temperature at the same location on the elliptical bearing profile. An elliptical journal bearing with journal diameter=100 mm, L/D ratio=1.0, Ellipticity Ratio=1.0 and radial clearance=0.1 mm has been designed and tested to access the pressure and temperature rise of the oil film at the central plane of the bearing. Two different lobes of positive pressure have been obtained for elliptical bearing which results in smaller area for cavitation zone and accounts for better thermal stability. Also, with the increase in load both pressure and temperature of an oil film increases for all the three grades of oil. Experimentally, it has been established that the HYDROL 68 is suitable grade of lubricating oil which gives the optimum rise of pressure and temperate under all operating conditions among the lubricating oils under study.

  9. Nonlinear Dynamics Analysis of Tilting Pad Journal Bearing-Rotor System

    Jiayang Ying

    2011-01-01

    Full Text Available The nonlinear dynamics theory is increasingly applied in the dynamics analysis of tilting pad journal bearing-rotor system. However, extensive work on system dynamics done previously neglects the influence caused by the moment of inertia of the pad. In this paper, a comparison is made between the responses of the rotor in the bearings with and without pad inertia effect. Taking the Jeffcott rotor system as an example, the characteristics of bearing-rotor system, such as bifurcation diagram, cycle response, frequency spectrum, phase trajectories, and Poincaré maps, were attained within a certain rotation rate range. The pivotal oil-film force of tilting pad journal bearing was calculated by database method. The results directly demonstrate that considering the influence of the pad moment of inertia, system dynamics characteristics are found more complicated when rotor-bearing system works around natural frequency and system bifurcation is observed forward when rotor-bearing system works on high-speed range.

  10. Hydrate bearing clayey sediments: Formation and gas production concepts

    Jang, Jaewon; Santamarina, Carlos

    2016-01-01

    Hydro-thermo-chemo and mechanically coupled processes determine hydrate morphology and control gas production from hydrate-bearing sediments. Force balance, together with mass and energy conservation analyses anchored in published data provide robust asymptotic solutions that reflect governing processes in hydrate systems. Results demonstrate that hydrate segregation in clayey sediments results in a two-material system whereby hydrate lenses are surrounded by hydrate-free water-saturated clay. Hydrate saturation can reach ≈2% by concentrating the excess dissolved gas in the pore water and ≈20% from metabolizable carbon. Higher hydrate saturations are often found in natural sediments and imply methane transport by advection or diffusion processes. Hydrate dissociation is a strongly endothermic event; the available latent heat in a reservoir can sustain significant hydrate dissociation without triggering ice formation during depressurization. The volume of hydrate expands 2-to-4 times upon dissociation or CO2single bondCH4 replacement. Volume expansion can be controlled to maintain lenses open and to create new open mode discontinuities that favor gas recovery. Pore size is the most critical sediment parameter for hydrate formation and gas recovery and is controlled by the smallest grains in a sediment. Therefore any characterization must carefully consider the amount of fines and their associated mineralogy.

  11. Hydrate bearing clayey sediments: Formation and gas production concepts

    Jang, Jaewon

    2016-06-20

    Hydro-thermo-chemo and mechanically coupled processes determine hydrate morphology and control gas production from hydrate-bearing sediments. Force balance, together with mass and energy conservation analyses anchored in published data provide robust asymptotic solutions that reflect governing processes in hydrate systems. Results demonstrate that hydrate segregation in clayey sediments results in a two-material system whereby hydrate lenses are surrounded by hydrate-free water-saturated clay. Hydrate saturation can reach ≈2% by concentrating the excess dissolved gas in the pore water and ≈20% from metabolizable carbon. Higher hydrate saturations are often found in natural sediments and imply methane transport by advection or diffusion processes. Hydrate dissociation is a strongly endothermic event; the available latent heat in a reservoir can sustain significant hydrate dissociation without triggering ice formation during depressurization. The volume of hydrate expands 2-to-4 times upon dissociation or CO2single bondCH4 replacement. Volume expansion can be controlled to maintain lenses open and to create new open mode discontinuities that favor gas recovery. Pore size is the most critical sediment parameter for hydrate formation and gas recovery and is controlled by the smallest grains in a sediment. Therefore any characterization must carefully consider the amount of fines and their associated mineralogy.

  12. Experimental Measurements of Journal Bearing Friction Using Mineral, Synthetic, and Bio-Based Lubricants

    Pantelis G. Nikolakopoulos

    2015-04-01

    Full Text Available The environmental impact of many industrial and naval applications is becoming increasingly important. Journal bearings are crucial components related with the reliable, safe and environmentally friendly operation of rotating machinery in many applications, e.g., in hydroplants, ships, power generation stations. The maintenance activities in certain cases also have considerable environmental impact. Fortunately, it is relatively easy to reduce the impact by changing the way lubricants are being used. Selecting the proper lubricant is important to sharply reduce long-term costs. The best-fit product selection can mean longer lubricant life, reduced machine wear, reduced incipient power losses and improved safety. Suitable basestocks and additives reduce environmental impact. In this paper, three types of lubricants are used in order to examine their effects on the tribological behavior of journal bearings. A mineral oil, a synthetic oil and a bio-based lubricant are experimentally and analytically examined for several configurations of load and journal rotational velocity. The friction forces and the hydrodynamic friction coefficients are calculated and compared. This investigation can assist the correct choice of lubricant in journal bearings with minimized environmental footprint.

  13. Optimization design of turbo-expander gas bearing for a 500W helium refrigerator

    Li, S. S.; Fu, B.; Y Zhang, Q.

    2017-12-01

    Turbo-expander is the core machinery of the helium refrigerator. Bearing as the supporting element is the core technology to impact the design of turbo-expander. The perfect design and performance study for the gas bearing are essential to ensure the stability of turbo-expander. In this paper, numerical simulation is used to analyze the performance of gas bearing for a 500W helium refrigerator turbine, and the optimization design of the gas bearing has been completed. And the results of the gas bearing optimization have a guiding role in the processing technology. Finally, the turbine experiments verify that the gas bearing has good performance, and ensure the stable operation of the turbine.

  14. Nonlinear dynamics of a flexible rotor supported by turbulent journal bearings with couple stress fluid

    Lo, C.-Y.; Chang-Jian, C.-W.

    2008-01-01

    This study presents a dynamic analysis of a rotor supported by two turbulent flow model journal bearings and lubricated with couple stress fluid under nonlinear suspension. The dynamics of the rotor center and bearing center is studied. The dynamic equations are solved using the Runge-Kutta method. The analysis methods employed in this study is inclusive of the dynamic trajectories of the rotor center and bearing center, power spectra, Poincare maps and bifurcation diagrams. The maximum Lyapunov exponent analysis is also used to identify the onset of chaotic motion. The results show that the values of dimensionless parameters l* strongly influence dynamic motions of bearing and rotor centre. It is found that couple stress fluid improve the stability of the system when l* > 0.4 even if the flow of this system is turbulent. We also demonstrated that the dimensionless rotational speed ratios s and the dimensionless unbalance parameter β are also significant system parameters. The modeling results thus obtained by using the method proposed in this paper can be employed to predict the stability of the rotor-bearing system and the undesirable behavior of the rotor and bearing center can be avoided

  15. SLPMC- New Self Lubricating Polymer Matrix Composites for Journal and Ball Bearing Applications in Space

    Merstallinger, A.; Macho, C.; Brodowski-Hanemann, G.; Bieringer, H.; Pambaguian, L.; Palladino, M.; Buttery, M.

    2015-09-01

    The paper is surveying the results of the ESA-project “SLPMC” covering the development of a self- lubricating polymer composite based on PTFE for use in bearings. The two targets of this project were to investigate lubrication mechanisms in PTFE-based composites under tribological conditions relevant to space applications (air, dry nitrogen, vacuum). And secondly, to develop a new composite to fulfil future needs by space applications. Hence, in the frame of this project several new composites based on PTFE-matrix with different kind of fillers were defined, manufactured and tested on material level. From the most promising variants bushes for journal bearings and cages for ball bearings were machined. Ball bearing tests were done in high vacuum up to 10 million revolutions.This paper summarises the main results from the project on material level focusing on tribological results derived by pin-on-disc tests. The influences of parameters like load, speed, atmosphere and temperature are discussed and compared to other already known materials. The paper also reports the findings from final ball bearing and plain bearing tests.

  16. Mechanical characterization of journal superconducting magnetic bearings: stiffness, hysteresis and force relaxation

    Cristache, Cristian; Valiente-Blanco, Ignacio; Diez-Jimenez, Efren; Alvarez-Valenzuela, Marco Antonio; Perez-Diaz, Jose Luis; Pato, Nelson

    2014-01-01

    Superconducting magnetic bearings (SMBs) can provide stable levitation without direct contact between them and a magnetic source (typically a permanent magnet). In this context, superconducting magnetic levitation provides a new tool for mechanical engineers to design non-contact mechanisms solving the tribological problems associated with contact at very low temperatures. In the last years, different mechanisms have been proposed taking advantage of superconducting magnetic levitation. Flywheels, conveyors or mechanisms for high-precision positioning. In this work the mechanical stiffness of a journal SMBs have been experimentally studied. Both radial and axial stiffness have been considered. The influence of the size and shape of the permanent magnets (PM), the size and shape of the HTS, the polarization and poles configuration of PMs of the journal SMB have been studied experimentally. Additionally, in this work hysteresis behavior and force relaxation are considered because they are essential for mechanical engineer when designing bearings that hold levitating axles.

  17. Fault diagnosis for tilting-pad journal bearing based on SVD and LMD

    Zhang Xiaotao

    2016-01-01

    Full Text Available Aiming at fault diagnosis for tilting-pad journal bearing with fluid support developed recently, a new method based on singular value decomposition (SVD and local mean decomposition (LMD is proposed. First, the phase space reconstruction of Hankel matrix and SVD method are used as pre-filter process unit to reduce the random noises in the original signal. Then the purified signal is decomposed by LMD into a series of production functions (PFs. Based on PFs, time frequency map and marginal spectrum can be obtained for fault diagnosis. Finally, this method is applied to numerical simulation and practical experiment data. The results show that the proposed method can effectively detect fault features of tilting-pad journal bearing.

  18. Study of Dimple Effect on the Friction Characteristics of a Journal Bearing using Taguchi Method

    Murthy, A. Amar; Raghunandana, Dr.

    2018-02-01

    The effect of producing dimples using chemically etched techniques or by machining process on the surface of a journal bearing bushing to reduce the friction using Taguchi method is investigated. The data used in the present analysis is based on the results obtained by the series of experiments conducted to study the dimples effect on the Stribeck curve. It is statistically proved that producing dimples on the bushing surface of a journal bearing has significant effect on the friction coefficient when used with light oils. Also it is seen that there is an interaction effect between speeds-load and load-dimples. Hence the interaction effect, which are usually neglected should be considered during actual experiments that significantly contributes in reducing the friction in mixed lubrication regime. The experiments, if were conducted after Taguchi method, then the number of experiments would have been reduced to half of the actual set of experiments that were essentially conducted.

  19. Nonlinear effects caused by coupling misalignment in rotors equipped with journal bearings

    Pennacchi, Paolo; Vania, Andrea; Chatterton, Steven

    2012-07-01

    Misalignment is one of the most common sources of trouble of rotating machinery when rigid couplings connect the shafts. Ideal alignment of the shafts is difficult to be obtained and rotors may present angular and/or parallel misalignment (defined also as radial misalignment or offset). During a complete shaft revolution, a periodical change of the bearings load occurs in hyperstatic shaft-lines, if coupling misalignment between the shafts is excessive. If the rotating machine is equipped with fluid-film journal bearings, the change of the loads on the bearing causes also the variation of their instantaneous dynamic characteristics, i.e. damping and stiffness, and the complete system cannot be considered any longer as linear. Despite misalignment is often observed in the practice, there are relatively few studies about this phenomenon in literature and their results are sometimes conflicting. The authors aim at modeling accurately this phenomenon, for the first time in this paper, and giving pertinent diagnostic information. The proposed method is suitable for every type of shaft-line supported by journal bearings. A finite element model is used for the hyperstatic shaft-line, while bearing characteristics are calculated by integrating Reynolds equation as a function of the instantaneous load acting on the bearings, caused also by the coupling misalignment. The results obtained by applying the proposed method are shown by means of the simulation, in the time domain, of the dynamical response of a hyperstatic shaft-line. Nonlinear effects are highlighted and the spectral components of the system response are analyzed, in order to give diagnostic information about the signature of this type of fault.

  20. Analysis of the Journal Bearing Friction Losses in a Heavy-Duty Diesel Engine

    Christoph Knauder

    2015-04-01

    Full Text Available Internal combustion engines (ICE for the use in heavy-duty trucks and buses have to fulfil demanding requirements for both vehicle efficiency as well as for emission of greenhouse gases. Beside the piston assembly the journal bearings are among the largest contributors to friction in the ICE. Through a combination of measurements and validated simulation methods the journal bearing friction losses of a state-of-the-art heavy-duty Diesel engine are investigated for a large range of real world operating conditions. To this task recently developed and extensively validated simulation methods are used together with realistic lubricant models that consider the Non-Newtonian behaviour as well as the piezoviscous effect. In addition, the potential for further friction reduction with the use of ultra-low viscosity lubricants is explored. The results reveal a potential of about 8% friction reduction in the journal bearings using a 0W20 ultra-low viscosity oil with an HTHS-viscosity (The HTHS-viscosity is defined as the dynamic viscosity of the lubricant measured at 150 °C and at a shear rate of 106 s

  1. High-BTU gas production from tar-bearing hot coke oven gas over iron catalyst

    L.Y. Li; K. Morishita; T. Takarada [Gunma University, Gunma (Japan). Department of Biological and Chemical Engineering

    2005-07-01

    To utilize the tar-bearing hot coke oven gas (the by-product of coke making process) more effectively, a process was developed by converting the hot coke oven gas into a methane rich high-BTU gas over iron-bearing catalysts. The catalytic behaviour of Indonesian limonite ore was mainly discussed. For a reference, a conventional nickel catalyst (Ni/Al{sub 2}O{sub 3}) was employed. Laboratory scale tests were carried out in a two-stage fixed-bed reactor at ambient pressure. A bituminous coal sample was heated at first stage, the volatiles was carried by feed gas and decomposed at second stage. The limonite promoted hydropyrolysis of coal volatiles similar to Ni/Al{sub 2}O{sub 3} catalyst. High yields of total product gas and methane were obtained at 50 vol.% hydrogen atmosphere with a feed gas of 60 ml min{sup -1} hydrogen and 60 ml min{sup -1} nitrogen. After experiments, hydrocarbons heavier than ethane were not observed. Also that, carbon balance was more than 99.8% in coal char, product gases and carbon deposits. It was considered that coal volatiles converted into light gases and carbon almost completely in catalyst bed. Yields of product gas and methane depended upon catalytic temperature. At 923 K, the maximum yield of product gas was achieved at 74.3% for limonite catalyst on carbon balance with methane 83.2 vol.% of the carbonaceous gas products. Comparing with limonite, Fe/Al{sub 2}O{sub 3} and BOF dust samples showed low activities on coal volatiles catalytic decomposition. 21 refs., 5 figs., 3 tabs.

  2. The Impact of Convective Fluid Inertia Forces on Operation of Tilting-Pad Journal Bearings

    Thomas Hagemann

    2017-01-01

    Full Text Available This paper presents a combination of experimental data, CFD analyses, and bearing code predictions on emergence of convective inertia fluid forces within the lube oil flow of tilting-pad journal bearings. Concordantly, experimental data and CFD analyses show a significant rise of local pressure at the transition between inlet and leading edge of tilting-pad, especially for high-speed applications with surface speeds up to 100 m/s. This effect can be related to convective inertia forces within fluid flow as cross-sections and flow character rapidly change at the pad entrance. An energy-based approach is implemented in the bearing code in order to provide enhanced boundary conditions for Reynolds equation considering this effect. As a result, predictions of bearing code achieved significant improved correlation with measured pressure distributions and CFD-data. Further, beside the local influence, a nonnegligible impact on characteristic parameters of bearing operation such as maximum temperature and stiffness and damping coefficients is observed. Finally, the results are critically analyzed and requirements to gain more distinct and reliable data are specified.

  3. Static Properties of Superconductor Journal Bearing Substator for Superconductor Flywheel Energy Storage System

    Park, B. J.; Jung, S. Y.; Lee, J. P.; Park, B. C.; Jeong, N. H.; Sung, T. H.; Han, Y. H.

    2008-01-01

    A Superconductor Flywheel Energy Storage System(SFES) mainly consists of a pair of non-contacting High Temperature Superconductor(HTS) bearings that provide very low frictional losses, a composite flywheel with high energy storage density. The HTS bearings, which offer dynamic stability without active control, are the key technology that distinguishes the SFES from other flywheel energy storage devices, and great effort is being put into developing this technology. The Superconductor Journal Bearing(SJB) mainly consists of HTS bulks and a stator, which holds the HTS bulks and also acts as a cold head. Static properties of HTS bearings provide data to solve problems which may occur easily in a running system. Since stiffness to counter vibration is the main parameter in designing an HTS bearing system, we investigate SJB magnetic force through static properties between the Permanent Magnet(PM) and HTS. We measure stiffness in static condition and the results are used to determine the optimal number of HTS bulks for a 100kWh SFES.

  4. Calculation methods for externally pressurised (hydrostatic) journal bearings with capillary restrictor control

    1992-09-01

    ESDU 92026 provides a procedure for the design and performance analysis of the bearings with five or more identical equally-spaced rectangular recesses (or pockets) fed by identical capillary restrictors from a constant pressure supply. The method takes account of stiffness and overload capacity requirements and determines the bearing overall size and proportions from the required load, speed and shaft diameter, recommends the clearance and supply pressure, and defines the recess dimensions and capillary restrictor size from the properties of the chosen lubricant. Equations and charts allow prediction of the journal displacement under load, the power loss, the lubricant flow rate, and the bearing and lubricant temperatures. The method applies to laminar flow and guidance is given for assessing the onset of non-laminar flow in the bearing and restrictors. Guidance is also given on the likelihood of bearing-induced instability. The user is assisted by flowcharts in applying the method, and two practical worked examples illustrate the procedure. ESDU 92037 introduces a FORTRAN program that implements the method, and magnetic media are available in ESDUpac A9237.

  5. Design and fabrication of gas bearings for Brayton cycle rotating unit

    Frost, A.; Tessarzik, J. M.; Arwas, E. B.; Waldron, W. D. (Editor)

    1973-01-01

    Analysis, design, and testing of two types of pivoted pad journal bearings and a spiral-grooved thrust bearing suitable for direct installation into the NASA 2 to 15 KW Brayton Cycle Rotating Unit (BRU) have been accomplished. Both types of tilting pad bearing assemblies are of the preloaded type, consisting of three pads with one pad flexibly mounted. One type utilizes a non-conforming pivot, while the other replaces the conventional spherical pivot with a cruciform flexible member. The thrust bearing is flexure mounted to accommodate static machine mislinement. Test results indicate that both types of journal bearings should satisfy the requirements imposed by the BRU. Hydrostatic tests of the spiral-grooved thrust bearing showed it to be free of pneumatic hammer with as many as 24 orifices over the BRU pressure and load range.

  6. Dynamical Simulations of a Flexible Rotor in Cylindrical Uncavitated and Cavitated Lubricated Journal Bearings

    Alessandro Ruggiero

    2018-04-01

    Full Text Available Due to requirements of their operating conditions, such as high speed, high flexibility and high efficiency, rotating machines are designed to obtain larger operating ranges. These operating conditions can increase the risk of fluid-induced instability. In fact, the presence of non-linear fluid forces when the threshold speed is overcome by the rotational speed, can generate rotor lateral self-excited vibrations known as “oil whirl” or “oil whip”. These instabilities derive from the interaction between the rotor and the sliding bearing and they are typically sub-synchronous and they contribute to eventual rubbing between rotor and stator with consequent damage to the rotating machines. For these reasons, the aim of this paper is to numerically investigate the differences in the dynamic behaviour of a flexible rotor supported by cylindrical lubricated journal bearings. The study considers two different cases, uncavitated and cavitated lubricated films, in order to develop an original Matlab-Simulink algorithm for the numerical solution of the differential non-linear equations of motion of the unbalanced flexible rotor supported on hydrodynamic journal bearings. The bearings were modelled as uncavitated and cavitated (π-Film short bearings derived from classical Reynolds’ theory. Dynamic simulation allowed prediction of the shape and size of the orbit performed by the system and evaluation of the vibrating phenomena exerted by the rotor during the motion. The results show that cavitation completely modifies the behaviour of the system in every aspect. The analysis of the diagrams obtained showed that the proposed algorithm provides consistent results and represents a valuable instrument for dynamic analysis of rotating systems.

  7. Identification Methods and Test Results for Tilting Pad and Fixed Geometry Journal Bearing Dynamic Coefficients – A Review

    T.W. Dimond

    2009-01-01

    Full Text Available Fluid film journal bearings (FFBs are used to support high-speed rotors in turbomachinery which often operate above the rotor first bending critical speed. The FFBs provide both lateral support and dynamic coefficients: stiffness, damping, and mass terms, related to machine vibrations. Detailed numerical values of the bearing dynamic characteristics are necessary for proper design and operation of rotating machinery.

  8. Cavitation Estimates by Orbit Prediction of a Journal Bearing - Finite Element Modelling and Experimental Studies Cavitation Estimates by Orbit Prediction of a Journal Bearing - Finite Element Modelling and Experimental Studies

    Christiansen, Christian Kim; Klit, Peder; Walther, Jens Honore

    2015-01-01

    The paper presents a two-sided approach to establish understanding of the cavitation phenomenon in dynamically loaded journal bearings, more specifically the engine bearings of large two-stroke marine diesel engines. One disadvantage of the journal bearing is the converging-diverging geometry....... Validation of the results is done against the Ruston and Hornsby 6VEB-X Mk III engine. Besides the numerical investigations a cavitation test rig has been developed. With this rig it is possible to generate cavitation under controlled conditions in terms ofload/eccentricity and rotational speed...

  9. Investigations of Slip Effect on the Performance of Micro Gas Bearings and Stability of Micro Rotor-Bearing Systems

    Jieyu Chen

    2007-08-01

    Full Text Available Incorporating the velocity slip effect of the gas flow at the solid boundary, theperformance and dynamic response of a micro gas-bearing-rotor system are investigated inthis paper. For the characteristic length scale of the micro gas bearing, the gas flow in thebearing resides in the slip regime rather than in the continuum regime. The modifiedReynolds equations of different slip models are presented. Gas pressure distribution and loadcarrying capacity are obtained by solving the Reynolds equations with finite differentmethod (FDM. Comparing results from different models, it is found that the second orderslip model agrees reasonably well with the benchmarked solutions obtained from thelinearized Boltzmann equation. Therefore, dynamic coefficients derived from the secondorder slip model are employed to evaluate the linear dynamic stability and vibrationcharacteristics of the system. Compared with the continuum flow model, the slip effectreduces dynamic coefficients of the micro gas bearing, and the threshold speed for stableoperation is consequently raised. Also, dynamic analysis shows that the system responseschange with variation of the operating parameters including the eccentricity ratio, therotational speed, and the unbalance ratio.

  10. Approximate solution of oil film load-carrying capacity of turbulent journal bearing with couple stress flow

    Zhang, Yongfang; Wu, Peng; Guo, Bo; Lü, Yanjun; Liu, Fuxi; Yu, Yingtian

    2015-01-01

    The instability of the rotor dynamic system supported by oil journal bearing is encountered frequently, such as the half-speed whirl of the rotor, which is caused by oil film lubricant with nonlinearity. Currently, more attention is paid to the physical characteristics of oil film due to an oil-lubricated journal bearing being the important supporting component of the bearing-rotor systems and its nonlinear nature. In order to analyze the lubrication characteristics of journal bearings efficiently and save computational efforts, an approximate solution of nonlinear oil film forces of a finite length turbulent journal bearing with couple stress flow is proposed based on Sommerfeld and Ocvirk numbers. Reynolds equation in lubrication of a finite length turbulent journal bearing is solved based on multi-parametric principle. Load-carrying capacity of nonlinear oil film is obtained, and the results obtained by different methods are compared. The validation of the proposed method is verified, meanwhile, the relationships of load-carrying capacity versus eccentricity ratio and width-to-diameter ratio under turbulent and couple stress working conditions are analyzed. The numerical results show that both couple stress flow and eccentricity ratio have obvious influence on oil film pressure distribution, and the proposed method approximates the load-carrying capacity of turbulent journal bearings efficiently with various width-to-diameter ratios. This research proposes an approximate solution of oil film load-carrying capacity of turbulent journal bearings with different width-to-diameter ratios, which are suitable for high eccentricity ratios and heavy loads.

  11. Feedback-controlled lubrication for reducing the lateral vibration of flexible rotors supported by tilting-pad journal bearings

    Salazar, Jorge Andrés González; Santos, Ilmar

    2015-01-01

    function is optimized in the stabilizing gain domain and then chosen from a subdomain imposed by servovalve restrictions. This work demonstrates enhancements of the dynamic response of flexible rotor-bearing systems supported by an active tilting-pad journal bearing by means of the feedback......The feedback-controlled lubrication regime, based on a model-free designed proportional–derivative controller, is experimentally investigated in a flexible rotor mounted on an actively-lubricated tilting-pad journal bearing. With such a lubrication regime, both the resulting pressure distribution...

  12. Omnidirectional regeneration (ODR) of proximity sensor signals for robust diagnosis of journal bearing systems

    Jung, Joon Ha; Jeon, Byung Chul; Youn, Byeng D.; Kim, Myungyon; Kim, Donghwan; Kim, Yeonwhan

    2017-06-01

    Some anomaly states of journal bearing rotor systems are direction-oriented (e.g., rubbing, misalignment). In these situations, vibration signals vary according to the direction of the sensors and the health state. This makes diagnosis difficult with traditional diagnosis methods. This paper proposes an omnidirectional regeneration method to develop a robust diagnosis algorithm for rotor systems. The proposed method can generate vibration signals in arbitrary directions without using extra sensors. In this method, signals are generated around the entire circumference of the rotor to consider all possible directions. Then, the directionality of each state is proved by mathematically and is evaluated using a proposed metric. When a directional state is determined, the classification is carried out on all of the generated signals. When a non-directional state is found, the classification is performed on only one of the generated signals to minimize computational load without sacrificing accuracy. The proposed ODR method was validated using experimental data. The classification results show that the proposed method generally outperforms the conventional classification method. The results support the proposed concept of using ODR signals in diagnosis procedures for journal bearing systems.

  13. Improvement of Dynamic Performance of Hybrid Gas Bearings via Adjustable Lubrication

    Pierart Vásquez, Fabián Gonzalo; Santos, Ilmar

    2013-01-01

    and the pressure and velocity fields in the injection nozzle are compared. The simplified theoretical model has been validated against the CFD results and experimentally using a test rig. The test rig consists of a flexible rotor supported by a ball bearing and a controllable hybrid gas bearing. The results show...

  14. Analysis of HD Journal Bearings Considering Elastic Deformation and Non-Newtonian Rabinowitsch Fluid Model

    J. Javorova

    2016-06-01

    Full Text Available The purpose of this paper is to study the performance of a finite length journal bearing, taking into account effects of non-Newtonian Rabinowitsch flow rheology and elastic deformations of the bearing liner. According to the Rabinowitsch fluid model, the cubic-stress constitutive equation is used to account for the non-Newtonian effects of pseudoplastic and dilatant lubricants. Integrating the continuity equation across the film, the nonlinear non-Newtonian Reynolds-type equation is derived. The elasticity part of the problem is solved on the base of Vlassov model of an elastic foundation. The numerical solution of the modified Reynolds equation is carried out by using FDM with over-relaxation technique. The results for steady state bearing performance characteristics have been calculated for various values of nonlinear factor and elasticity parameters. It was concluded that in comparison with the Newtonian lubricants, higher values of film pressure and load carrying capacity have been obtained for dilatant lubricants, while the case was reversed for pseudoplastic lubricants.

  15. Steady state characteristics of a tilting pad journal bearing with controllable lubrication: Comparison between theoretical and experimental results

    Cerda Varela, Alejandro Javier; Nielsen, Bo Bjerregaard; Santos, Ilmar

    2013-01-01

    direction. The modification of the injection pressure enables to modify the bearing static and dynamic properties according to the operational needs. The results presented are obtained using a theoretical model, which considers all the effects that determine the bearing behavior (controllable......This paper is aimed at presenting results regarding the static and thermal behavior of a tilting-pad journal bearing operating under controllable regime. The bearing is rendered controllable by injecting high pressure oil into the clearance using holes drilled across the bearing pads in the radial...... elastothermohydrodynamic lubrication regime), as well as using a test rig designed and built to this effect. The comparison between experimental and theoretical results provides solid ground to determine the accuracy of the available model for the the prediction of the steady-state behavior of the tilting-pad bearing...

  16. In vivo evaluation of zirconia ceramic in the DexAide right ventricular assist device journal bearing.

    Saeed, Diyar; Shalli, Shanaz; Fumoto, Hideyuki; Ootaki, Yoshio; Horai, Tetsuya; Anzai, Tomohiro; Zahr, Roula; Horvath, David J; Massiello, Alex L; Chen, Ji-Feng; Dessoffy, Raymond; Catanese, Jacquelyn; Benefit, Stephen; Golding, Leonard A R; Fukamachi, Kiyotaka

    2010-06-01

    Zirconia is a ceramic with material properties ideal for journal bearing applications. The purpose of this study was to evaluate the use of zirconium oxide (zirconia) as a blood journal bearing material in the DexAide right ventricular assist device. Zirconia ceramic was used instead of titanium to manufacture the DexAide stator housing without changing the stator geometry or the remaining pump hardware components. Pump hydraulic performance, journal bearing reliability, biocompatibility, and motor efficiency data of the zirconia stator were evaluated in six chronic bovine experiments for 14-91 days and compared with data from chronic experiments using the titanium stator. Pump performance data including average in vivo pump flows and speeds using a zirconia stator showed no statistically significant difference to the average values for 16 prior titanium stator in vivo studies, with the exception of a 19% reduction in power consumption. Indices of hemolysis were comparable for both stator types. Results of coagulation assays and platelet aggregation tests for the zirconia stator implants showed no device-induced increase in platelet activation. Postexplant evaluation of the zirconia journal bearing surfaces showed no biologic deposition in any of the implants. In conclusion, zirconia ceramic can be used as a hemocompatible material to improve motor efficiency while maintaining hydraulic performance in a blood journal bearing application.

  17. From Hybrid to Actively-Controlled Gas Lubricated Bearings – Theory and Experiment

    Morosi, Stefano

    bearings, tilting pad and flexure pivot gas bearings. These solutions proved to be effective in improving static and dynamic properties of the bearings, however issues related to the manufacturing and accuracy of predictions has so far limited their applications. Another drawback is that passive bearings......-rig are backed by a comprehensive mathematical model that couples a finite element model of a flexible rotor, a thermohydrodynamic model based on a modified form of the Reynold’s equation for hybrid aerostatic-aerodynamic lubrication of compressible fluid, a piezoelectric injection system and a proportional...

  18. Closed loop identification of a piezoelectrically controlled radial gas bearing: Theory and experiment

    Sekunda, André Krabdrup; Niemann, Hans Henrik; Poulsen, Niels Kjølstad

    2018-01-01

    Gas bearing systems have extremely small damping properties. Feedback control is thus employed to increase the damping of gas bearings. Such a feedback loop correlates the input with the measurement noise which in turn makes the assumptions for direct identification invalid. The originality...... of this article lies in the investigation of the impact of using different identification methods to identify a rotor-bearing systems’ dynamic model when a feedback loop is active. Two different identification methods are employed. The first method is open loop Prediction Error Method, while the other method...

  19. Some Experimental and Simulation Results on the Dynamic Behaviour of Spur and Helical Geared Transmissions with Journal Bearings

    R. Fargère

    2012-01-01

    Full Text Available Some interactions between the dynamic and tribological behaviour of geared transmissions are examined, and a number of experimental and simulation results are compared. A model is introduced which incorporates most of the possible interactions between gears, shafts and hydrodynamic journal bearings. It combines (i a specific element for wide-faced gears that includes the normal contact conditions between actual mating teeth, that is, with tooth shape deviations and mounting errors, (ii shaft finite elements, and (iii the external forces generated by journal bearings determined by directly solving Reynolds' equation. The simulation results are compared with the measurement obtained on a high-precision test rig with single-stage spur and helical gears supported by hydrodynamic journal bearings. The experimental and simulation results compare well thus validating the simulation strategy both at the global and local scales.

  20. Dynamic Stability Study of Static Gas Bearing for Small Cryogenic Turbo-Expander

    Wang Xuemin; Zhuang Ming; Zhang Qiyong; Li Shanshan; Fu Bao

    2011-01-01

    An experimental method is presented to analyze the dynamic stability of the gas bearing for small cryogenic turbo-expanders. The rotation imbalance response and the shape of the rotor orbit were obtained for different speeds up to 110,000 rpm, and the critical speed of the rotor-bearing system was determined by a Bode diagram. An FFT signal analytical method was applied to identify the resonance frequency, and the waterfall plot was presented. During the whole process of speeding up to the designed speed of 110,000 rpm, the rotor-bearing works stably with no whirl instability, which is validated in a waterfall plot. Also, the tested rotor-bearing model was analyzed theoretically. It was proved that the experimental results were highly consistent with those of theoretical calculations. Thus the experimental method proposed here to analyze the dynamic stability of the gas bearing is feasible. (fusion engineering)

  1. Operating experience of gas bearing helium circulators in HTGR development facility

    Shimomura, H.; Kawaji, S.; Fujisaki, K.; Ihizuka, T.

    1988-01-01

    The large scale helium gas test facility (HENDEL) has been constructed and operated since March 1982 at the Japan Atomic Energy Research Institute to develop HTGR components. The five electric driven gas circulators with dynamic gas bearings are used to circulate the helium gas of 4MPa and 400 deg. C in loops for their compactness, gas tightness, easy maintenance and free from gas contamination. All of these circulators are variable speed types of 3,000 to 12,000 rpm and have the same gas bearings and electric motors. The four machines among them are equipped with centrifugal impeller and one other machine has regenerative type, and the weight of both type rotors are nearly the same. After the troubles and repairing, both type of circulators were tested and the vibration characteristics were measured as preventing maintenance. From the test and measurements of the circulators, it was presumed that the first trouble on regenerative type was caused from excess unbalance force by falling off of a small pin from the rotating part and the second severe trouble on it was caused by the whipping in gas bearing. The static load on tilting pads indicated close relations to occurrence of the whirling through the measurements. It is recognized that fine balancing of the rotors and delicate clearance adjustment of the bearings are very important for the rotor stability and that the mechanism should be designed and machined so precise as to be adjustable. As the gas bearing would be damaged in an instantaneously short time, the monitoring technique for it should be so fast and predictive as to prevent serious damage. Through the tests, the vibration spectrum monitoring method seems to be predictive and useful for early detection of the shaft instability. It will be concluded that the gas bearing machine is an excellent system in its design philosophy, however, it also needs highly precise machining and delicate maintenance technique. 4 refs, 10 figs, 1 tab

  2. Characterization of High-Power Turbomachinery Tilting Pad Journal Bearings: First Results Obtained on a Novel Test Bench

    Enrico Ciulli

    2018-01-01

    Full Text Available Tilting pad journal bearings are usually employed in turbomachines for their stable behavior at high rotational speeds. Devoted test rigs have been realized to validate the predictions of theoretical models. However, the design of new high-performance and large-size bearings needs to be supported by experimental investigations on high-performance large test rigs. The main characteristics of a recently built facility for testing large tilting pad journal bearings with diameters from 150 to 300 mm are described in this work. The test rig is versatile and can be used to test bearings of different size, configurations and to investigate the influence of many parameters, even the effect of misalignment. Sample results of the static characterization of a four-pad high-performance tilting pad journal bearing are reported evidencing some transient effects. A few sample dynamic results are also reported. The presented experimental results demonstrated the capabilities of the rig for investigating the static and the dynamic characteristics of the bearings accurately measuring slow and fast variables.

  3. Development of surface coatings for air-lubricated, compliant journal bearings to 650 C

    Bhushan, B.; Gray, S.

    1978-01-01

    Surface coatings for an air-lubricated, compliant journal for an automotive gas turbine engine were tested to find those capable of withstanding temperatures of either 540 C (1000 F) or 650 C (1200 F). Also, the coatings have to be capable of surviving the start-stop sliding contact cycles prior to rotor lift-off and at touchdown. Selected coating combinations were tested in start-stop tests at 14 kPa (2 psi) loading for 2000 cycles at room and maximum temperatures. Specific coating recommendations are: Cdo and graphite on foil versus chrome carbide on journal up to 370 C (700 F); NASA PS-120 (Tribaloy 400, silver, and CaF2) on journal versus uncoated foil up to 540 C (1000 F); and chemically adherent Cr2O3 on journal and foil up to 650 C (1200 F). The chemically adherent Cr2O3 coating system was further tested successfully at 35 kPa (5 psi) loading for 2000 start-stop cycles.

  4. Compensation of Cross-Coupling Stiffness and Increase of Direct Damping in Multirecess Journal Bearings using Active Hybrid Lubrication

    Santos, Ilmar; Watanabe, F.Y.

    2004-01-01

    journal bearings (HJB). When part of hydrostatic pressure is also dynamically modified by means of hydraulic control systems, one refers to the active lubrication. The main contribution of the present theoretical work is to show that it is possible to reduce cross-coupling stiffness and increase...

  5. Performance of two-lobe hole-entry hybrid journal bearing system under the combined influence of textured surface and couple stress lubricant

    Khatri, Chandra B.; Sharma, Satish C.

    2018-02-01

    Textured surface in journal bearings is becoming an important area of investigation during the last few years. Surface textures have the shapes of micro-dimple with a small diameter and depth having order of magnitude of bearing clearance. This paper presents the influence of couple stress lubricant on the circular and non-circular hole-entry hybrid journal bearing system and reports the comparative study between the textured and non-textured circular/non-circular hybrid journal bearing system. The governing Reynolds equation has been modified for the couple stress lubricant flow in the clearance of bearing and journal. The FEM technique has been applied to solve the modified Reynolds equation together with restrictor flow equation. The numerically simulated results indicate that the influence of couple stress lubricant is significantly more in textured journal bearing than that of non-textured journal bearing. Further, it has been observed that the textured two-lobe (δ = 1.1) hybrid journal bearing lubricated with couple stress lubricant provides larger values of fluid film stiffness coefficients and stability threshold speed against other bearings studied in the present paper.

  6. Effects of Gas Rarefaction on Dynamic Characteristics of Micro Spiral-Grooved Thrust Bearing

    Liu, Ren; Wang, Xiao-Li; Zhang, Xiao-Qing

    2012-01-01

    The effects of gas-rarefaction on dynamic characteristics of micro spiral-grooved-thrust-bearing are studied. The Reynolds equation is modified by the first order slip model, and the corresponding perturbation equations are then obtained on the basis of the linear small perturbation method. In the converted spiral-curve-coordinates system, the finite-volume-method (FVM) is employed to discrete the surface domain of micro bearing. The results show, compared with the continuum-flow model, that ...

  7. Conical Magnetic Bearings Developed for Active Stall Control in Gas Turbine Engines

    Trudell, Jeffrey J.; Kascak, Albert F.; Provenza, Andrew J.; Buccieri, Carl J.

    2004-01-01

    Active stall control is a current research area at the NASA Glenn Research Center that offers a great benefit in specific fuel consumption by allowing the gas turbine to operate beyond the onset of stall. Magnetic bearings are being investigated as a new method to perform active stall control. This enabling global aviation safety technology would result in improved fuel efficiency and decreased carbon dioxide emissions, as well as improve safety and reliability by eliminating oil-related delays and failures of engine components, which account for 40 percent of the commercial aircraft departure delays. Active stall control works by perturbing the flow in front of the compressor stage such that it cancels the pressure wave, which causes the compressor to go into stall. Radial magnetic bearings are able to whirl the shaft so that variations in blade tip leakage would flow upstream causing a perturbation wave that could cancel the rotating stall cell. Axial or thrust magnetic bearings cannot be used to cancel the surge mode in the compressor because they have a very low bandwidth and thus cannot modulate at a high enough frequency. Frequency response is limited because the thrust runner cannot be laminated. To improve the bandwidth of magnetic thrust bearings, researchers must use laminations to suppress the eddy currents. A conical magnetic bearing can be laminated, resulting in increased bandwidth in the axial direction. In addition, this design can produce both radial and thrust force in a single bearing, simplifying the installation. The proposed solution combines the radial and thrust bearing into one design that can be laminated--a conical magnetic bearing. The new conical magnetic bearing test rig, funded by a Glenn fiscal year 2002 Director's Discretionary Fund, was needed because none of the existing rigs has an axial degree of freedom. The rotor bearing configuration will simulate that of the main shaft on a gas turbine engine. One conical magnetic bearing

  8. Greenhouse gas mitigation can reduce sea-ice loss and increase polar bear persistence

    Amstrup, Steven C.; Deweaver, E.T.; Douglas, David C.; Marcot, B.G.; Durner, George M.; Bitz, C.M.; Bailey, D.A.

    2010-01-01

    On the basis of projected losses of their essential sea-ice habitats, a United States Geological Survey research team concluded in 2007 that two-thirds of the worlds polar bears (Ursus maritimus) could disappear by mid-century if business-as-usual greenhouse gas emissions continue. That projection, however, did not consider the possible benefits of greenhouse gas mitigation. A key question is whether temperature increases lead to proportional losses of sea-ice habitat, or whether sea-ice cover crosses a tipping point and irreversibly collapses when temperature reaches a critical threshold. Such a tipping point would mean future greenhouse gas mitigation would confer no conservation benefits to polar bears. Here we show, using a general circulation model, that substantially more sea-ice habitat would be retained if greenhouse gas rise is mitigated. We also show, with Bayesian network model outcomes, that increased habitat retention under greenhouse gas mitigation means that polar bears could persist throughout the century in greater numbers and more areas than in the business-as-usual case. Our general circulation model outcomes did not reveal thresholds leading to irreversible loss of ice; instead, a linear relationship between global mean surface air temperature and sea-ice habitat substantiated the hypothesis that sea-ice thermodynamics can overcome albedo feedbacks proposed to cause sea-ice tipping points. Our outcomes indicate that rapid summer ice losses in models and observations represent increased volatility of a thinning sea-ice cover, rather than tipping-point behaviour. Mitigation-driven Bayesian network outcomes show that previously predicted declines in polar bear distribution and numbers are not unavoidable. Because polar bears are sentinels of the Arctic marine ecosystem and trends in their sea-ice habitats foreshadow future global changes, mitigating greenhouse gas emissions to improve polar bear status would have conservation benefits throughout

  9. Greenhouse gas mitigation can reduce sea-ice loss and increase polar bear persistence.

    Amstrup, Steven C; Deweaver, Eric T; Douglas, David C; Marcot, Bruce G; Durner, George M; Bitz, Cecilia M; Bailey, David A

    2010-12-16

    On the basis of projected losses of their essential sea-ice habitats, a United States Geological Survey research team concluded in 2007 that two-thirds of the world's polar bears (Ursus maritimus) could disappear by mid-century if business-as-usual greenhouse gas emissions continue. That projection, however, did not consider the possible benefits of greenhouse gas mitigation. A key question is whether temperature increases lead to proportional losses of sea-ice habitat, or whether sea-ice cover crosses a tipping point and irreversibly collapses when temperature reaches a critical threshold. Such a tipping point would mean future greenhouse gas mitigation would confer no conservation benefits to polar bears. Here we show, using a general circulation model, that substantially more sea-ice habitat would be retained if greenhouse gas rise is mitigated. We also show, with Bayesian network model outcomes, that increased habitat retention under greenhouse gas mitigation means that polar bears could persist throughout the century in greater numbers and more areas than in the business-as-usual case. Our general circulation model outcomes did not reveal thresholds leading to irreversible loss of ice; instead, a linear relationship between global mean surface air temperature and sea-ice habitat substantiated the hypothesis that sea-ice thermodynamics can overcome albedo feedbacks proposed to cause sea-ice tipping points. Our outcomes indicate that rapid summer ice losses in models and observations represent increased volatility of a thinning sea-ice cover, rather than tipping-point behaviour. Mitigation-driven Bayesian network outcomes show that previously predicted declines in polar bear distribution and numbers are not unavoidable. Because polar bears are sentinels of the Arctic marine ecosystem and trends in their sea-ice habitats foreshadow future global changes, mitigating greenhouse gas emissions to improve polar bear status would have conservation benefits throughout

  10. Analysis of the gas-lubricated flat-sector-pad thrust bearing

    Etsion, I.

    1976-01-01

    A flat sector-shaped pad geometry for a gas-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. It is shown that maximum load capacity is achieved when the pad is tilted so as to create uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves, and a comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

  11. Enhancing damping of gas bearings using linear parameter-varying control

    Theisen, Lukas Roy Svane; Niemann, Hans Henrik; Galeazzi, Roberto

    2017-01-01

    systems to regulate the injection pressure of the fluid. Due to the strong dependencies of system performance on system parameters, the sought controller should be robust over a large range of operational conditions. This paper addresses the damping enhancement of controllable gas bearings through robust...... control approaches. Through an extensive experimental campaign the paper evaluates two robust controllers, a linear parametervarying (LPV) controller and ∞ controller, on their capability to guarantee stability and performance of a gas bearing across the large operational envelopes in rotational speed...

  12. Friction and Wear Reduction of Eccentric Journal Bearing Made of Sn-Based Babbitt for Ore Cone Crusher

    Amanov, Auezhan; Ahn, Byungmin; Lee, Moon Gu; Jeon, Yongho; Pyun, Young-Sik

    2016-01-01

    An anti-friction Babbitt alloy-coated bearing made by a casting process is a journal bearing, which is used in an ore cone crusher eccentric. The main purpose of the Babbitt coated eccentric is to provide a low friction to support and guide a rotating shaft. Despite the fact that the Babbitt-coated eccentric offers a low friction coefficient and can be operated without a continuous supply of lubricant, it suffers from mining environments and short service life. In this study, an ultrasonic na...

  13. Gas generation in pure and impure plutonium-bearing materials

    Mason, R.; Allen, T.; Eller, P.G.; Hagan, R.; Horrell, D.; Rink, N.

    1999-01-01

    The Los Alamos National Laboratory's (LANL's) materials identification and surveillance (MIS) project identifies materials to be stored in DOE-STD-3013-96 containers, determines the chemical and physical character of stored materials, and evaluates processing to be used to stabilize materials to meet the standard. The project has completed processing and analysis of 9 Hanford items and 24 Rocky Flats items, representing a substantial portion of the oxides to be packaged for long-term storage. The resultant data provide insight into the physical and chemical characteristics of the materials at the sites. A component of the study was to investigate gas generation for representative materials. These studies included headspace gas measurements over the 9 Hanford items, measurement of gas generation in 10-g surveillance samples of MIS powders, and pressure monitoring. Before examining the Hanford cans, sampling and analysis methods were demonstrated on HRA-905191, an item from the LANL vault. This item was not typical of materials designated to be stored in 3013 cans, as it contained plastic vials, emery cloths, paper towels, and a large percentage of thorium. However, it was one of the items that contained significant hydrogen in the headspace. A mass spectrometer was used to determine the composition of headspace gases. Oxygen was substantially depleted in all cases, and the percent of nitrogen in many items was greater than that found in air. In both cans with a high hydrogen content, the corresponding oxygen content was near zero (HRA905191 and ARF-102-85-365). In some cases, carbon dioxide was generated in the cans. Carbon monoxide was found in item BLO-39-11-85-295. This item has a high americium content, thus higher temperature than other materials examined. The only notable impurities in item BLO-39-11-85-295 were carbon at ≅0.1 wt% and chlorides at 0.2 wt%. Seven long-term surveillance vessels each holding approximately10 g of MIS powders have been monitored

  14. Greenhouse gas mitigation can reduce sea-ice loss and increase polar bear persistence

    Steven C. Amstrup; Eric T. DeWeaver; David C. Douglas; Bruce G. Marcot; George M. Durner; Cecilia M. Bitz; David A. Bailey

    2010-01-01

    On the basis of projected losses of their essential sea-ice habitats, a United States Geological Survey research team concluded in 2007 that two-thirds of the world's polar bears (Ursus maritimus) could disappear by mid-century if business-as-usual greenhouse gas emissions continue. That projection, however, did not consider the possible...

  15. FIRST OPERATING RESULTS OF A DYNAMIC GAS BEARING TURBINE IN AN INDUSTRIAL HYDROGEN LIQUEFIER

    Bischoff, S.; Decker, L.

    2010-01-01

    Hydrogen has been brought into focus of industry and public since fossil fuels are depleting and costs are increasing dramatically. Beside these issues new high-tech processes in the industry are in need for hydrogen at ultra pure quality. To achieve these requirements and for efficient transportation, hydrogen is liquefied in industrial plants. Linde Gas has commissioned a new 5.5 TPD Hydrogen liquefier in Leuna, Germany, which has been engineered and supplied by Linde Kryotechnik. One of the four expansion turbines installed in the liquefaction process is equipped with dynamic gas bearings. Several design features and operational characteristics of this application will be discussed. The presentation will include results of efficiency and operational reliability that have been determined from performance tests. The advantages of the Linde dynamic gas bearing turbine for future use in hydrogen liquefaction plants will be shown.

  16. On our own behalf: the journal 'Gas' as a marketing instrument

    Siegmund, H.

    1995-01-01

    Media characteristics of the journal 'gas': Target groups; sales strategy; editorial concept; qualification as an advertising medium; focal subjects; sponsored subscriptions; brief presentation of other publications about gas. The journal 'gas' has come to play a key role in natural gas marketing. Its concentration on crucial target groups and its unconventional sales strategy also makes the journal an interesting medium for advertisers. The article is complemented by a brief presentation of the more important media facts of other publications dealing with gas. (orig.) [de

  17. WAVELET-BASED ALGORITHM FOR DETECTION OF BEARING FAULTS IN A GAS TURBINE ENGINE

    Sergiy Enchev

    2014-07-01

    Full Text Available Presented is a gas turbine engine bearing diagnostic system that integrates information from various advanced vibration analysis techniques to achieve robust bearing health state awareness. This paper presents a computational algorithm for identifying power frequency variations and integer harmonics by using wavelet-based transform. The continuous wavelet transform with  the complex Morlet wavelet is adopted to detect the harmonics presented in a power signal. The algorithm based on the discrete stationary wavelet transform is adopted to denoise the wavelet ridges.

  18. Camshaft bearing arrangement

    Aoi, K.; Ozawa, T.

    1986-06-10

    A bearing arrangement is described for the camshaft of an internal combustion engine or the like which camshaft is formed along its length in axial order with a first bearing surface, a first cam lobe, a second bearing surface, a second cam lobe, a third bearing surface, a third cam lobe and a fourth bearing surface, the improvement comprising first bearing means extending around substantially the full circumference of the first bearing surface and journaling the first bearing surface, second bearing means extending around substantially less than the circumference of the second bearing surface and journaling the second bearing surface, third bearing means extending around substantially less than the circumference of the third bearing surface and journaling the third bearing surface, and fourth bearing means extending around substantially the full circumference of the fourth bearing surface and journaling the first bearing surface.

  19. A study on compliant layers and its influence on dynamic response of a hydrodynamic journal bearing

    Thomsen, Kim; Klit, Peder

    2011-01-01

    For some hydrodynamic bearing applications polymer-lined bearings are chosen over traditional metal alloy bearings due to their better wear and friction properties when operating at very thin films, e.g. in the mixed lubrication region. The introduction of a compliant layer also affects the dynamic...... used to evaluate hydrodynamic bearing designs: dynamic response, maximum pressure, minimum film thickness, wear, power loss and temperature response. The primary findings are that the maximum pressures are reduced significantly and this comes at the expense of slightly higher eccentricity ratios during...

  20. ELEMENT DESIGN FOR AN INKJET SYSTEM OF HYDROSTATIC GAS BEARING CONTROL

    T. E. Il'ina

    2015-09-01

    Full Text Available Subject of Study. The paper discusses the concept of inkjet systems application, also known as pneumonics, for automatic hydrostatic gas bearing control. Inkjet systems have the advantages over traditional control systems in those problems where the speed of traditional mechanical, electrical or hydraulic servomotors is not enough. Control of the shaft position in gas bearing with forced gas supply into the gap between the shaft and the bearing is typical for this class of problems. In this case, control means the pressure changing or flow rate of gas supplied to the gap by at least one of three axes at a frequency higher than the nominal speed of the shaft. Thus, high speed of response is required from the system. The objective of this work is to design a discrete jet element, testing of its geometry and switching characteristics. Main Results. The discrete inkjet element for oil-free non-contact transmission working on the refrigerant was designed. Relay transition process was modeled in the inkjet element with the use of numerical methods. The switching time has reached 0.2-0.3 ms; this is one order less than the requirements of aircraft control systems, which typically operate at a frequency of about 200 Hz. It is shown that periodic oscillations with high frequency occur when the control signal is injected with insufficient level of pressure. Therefore, a separate design task is to determine the minimum pressure allowable in the control channel.

  1. Fast discharging homopolar drum-type generator with gas bearing and flexible copper-fiber brushes

    Kibardin, A.S.; Komin, A.V.; Sojkin, V.F.; Frolkin, V.I.

    1984-01-01

    The description and results of testing schock-excited homopolar generator (SEHG) with a drum-type rotor, a gas bearing and flexible copper-fiber brushes are presented. SEHG has a magnetic core with two excitation coils with the designed field of 1.8-2 T in the gap. The drum-type titanium rotor has 80 kg, is 0.5 m in diameter, 0.25 m length and 0.05 m thick. SEHG power is 3.6 MJ, overall dimensions are 0.8x1 m. Single- and double-row bearings, representing an aluminium shell of 15 mm thick, established inside an external backward current lead and isolated from it, are used to control serviceability of a radial gas-static bearing, which is a support for an SEHG rotor. The bearing surface was covered with the colloidal graphite and had one or two rows by 24 openings for swelling. Brush units represent a bronze brush ring, containing 44 copper-fiber brushes. Tests results confirm serviceability of copper-fiber brushes with quite large dimensions and permit to count on producing the 2.4 MA electric discharge and 12 ms pulse rise time

  2. Effects of Gas Rarefaction on Dynamic Characteristics of Micro Spiral-Grooved Thrust Bearing.

    Liu, Ren; Wang, Xiao-Li; Zhang, Xiao-Qing

    2012-04-01

    The effects of gas-rarefaction on dynamic characteristics of micro spiral-grooved-thrust-bearing are studied. The Reynolds equation is modified by the first order slip model, and the corresponding perturbation equations are then obtained on the basis of the linear small perturbation method. In the converted spiral-curve-coordinates system, the finite-volume-method (FVM) is employed to discrete the surface domain of micro bearing. The results show, compared with the continuum-flow model, that under the slip-flow regime, the decrease in the pressure and stiffness become obvious with the increasing of the compressibility number. Moreover, with the decrease of the relative gas-film-thickness, the deviations of dynamic coefficients between slip-flow-model and continuum-flow-model are increasing.

  3. Active tilting-pad journal bearings supporting flexible rotors: Part II–The model-based feedback-controlled lubrication

    Salazar, Jorge Andrés González; Santos, Ilmar

    2017-01-01

    This is part II of a twofold paper series dealing with the design and implementation of model-based controllers meant for assisting the hybrid and developing the feedback-controlled lubrication regimes in active tilting pad journal bearings (active TPJBs). In both papers theoretical and experimen...... derived in part I. Results show further suppression of resonant vibrations when using the feedback-controlled or active lubrication, overweighting the reduction already achieved with hybrid lubrication, thus improving the whole machine dynamic performance.......This is part II of a twofold paper series dealing with the design and implementation of model-based controllers meant for assisting the hybrid and developing the feedback-controlled lubrication regimes in active tilting pad journal bearings (active TPJBs). In both papers theoretical...... and experimental analyses are presented with focus on the reduction of rotor lateral vibration. This part is devoted to synthesising model-based LQG optimal controllers (LQR regulator + Kalman Filter) for the feedback-controlled lubrication and is based upon the mathematical model of the rotor-bearing system...

  4. Aqueous process for recovering sulfur from hydrogen sulfide-bearing gas

    Basu, Arunabha

    2015-05-05

    A process for recovering sulfur from a hydrogen sulfide-bearing gas utilizes an aqueous reaction medium, a temperature of about 110-150.degree. C., and a high enough pressure to maintain the aqueous reaction medium in a liquid state. The process reduces material and equipment costs and addresses the environmental disadvantages associated with known processes that rely on high boiling point organic solvents.

  5. An application of gain-scheduled control using state-space interpolation to hydroactive gas bearings

    Theisen, Lukas Roy Svane; Camino, Juan F.; Niemann, Hans Henrik

    2016-01-01

    with a gain-scheduling strategy using state-space interpolation, which avoids both the performance loss and the increase of controller order associated to the Youla parametrisation. The proposed state-space interpolation for gain-scheduling is applied for mass imbalance rejection for a controllable gas...... bearing scheduled in two parameters. Comparisons against the Youla-based scheduling demonstrate the superiority of the state-space interpolation....

  6. Mathematical Model and Analysis of the Water-Lubricated Hydrostatic Journal Bearings considering the Translational and Tilting Motions

    Hui-Hui Feng

    2014-01-01

    Full Text Available The water-lubricated bearings have been paid attention for their advantages to reduce the power loss and temperature rise and increase load capacity at high speed. To fully study the complete dynamic coefficients of two water-lubricated, hydrostatic journal bearings used to support a rigid rotor, a four-degree-of-freedom model considering the translational and tilting motion is presented. The effects of tilting ratio, rotary speed, and eccentricity ratio on the static and dynamic performances of the bearings are investigated. The bulk turbulent Reynolds equation is adopted. The finite difference method and a linear perturbation method are used to calculate the zeroth- and first-order pressure fields to obtain the static and dynamic coefficients. The results suggest that when the tilting ratio is smaller than 0.4 or the eccentricity ratio is smaller than 0.1, the static and dynamic characteristics are relatively insensitive to the tilting and eccentricity ratios; however, for larger tilting or eccentricity ratios, the tilting and eccentric effects should be fully considered. Meanwhile, the rotary speed significantly affects the performance of the hydrostatic, water-lubricated bearings.

  7. Adjustable hybrid gas bearing – Influence of piezoelectrically adjusted injection on damping factors and natural frequencies of a flexible rotor operating under critical speeds

    Pierart, Fabián G.; Santos, Ilmar F.

    2016-01-01

    Damping factors and natural frequencies of a flexible rotor supported by a gas bearing with piezoelectrically adjusted flow, are theoretically determined using a rotor finite element model coupled with the modified Reynolds equation. An extra term is added to the standard formulation of Reynolds...... fourradial injectors equally pressurized. For the two configurations, the theoretical results are experimentally validated as afunction of the piezoactuators input voltage and the journal angular velocity. Results show a good agreement for natural frequencies and damping factors. Theoretical and experimental......,the damping factor associated with the first mode shape can be increased by 10 times when compared to four injectors equally pressurized....

  8. Feedback-Controlled Lubrication for Reducing the Lateral Vibration of Flexible Rotors supported by Tilting-Pad Journal Bearings

    Salazar, Jorge Andrés González; Santos, Ilmar

    2014-01-01

    In this work, the feedback-controlled lubrication regime, based on a model-free designed proportional-derivative (PD) controller, is studied and experimentally tested in a flexible rotor mounted on an actively-lubricated tilting-pad journal bearing (active TPJB). With such a lubrication regime...... to experimentally characterized multi-input multi-output systems is used to determine the stabilizing PD gain domain. The main contribution of this work is to demonstrate the enhancement of the dynamic response of a flexible rotor-bearing system supported by an active TPJB by means of the feedback...... are used as actuators and the flexible rotor lateral movements as feedback control signals. To synthesise the PD controller gains an objective function is optimized in the stabilizing gain domain and then chosen from a subdomain imposed by the servovalves restrictions. The D-decomposition approach expanded...

  9. Sedimentological Properties of Natural Gas Hydrates-Bearing Sands in the Nankai Trough and Mallik Areas

    Uchida, T.; Tsuji, T.; Waseda, A.

    2009-12-01

    The Nankai Trough parallels the Japanese Island, where extensive BSRs have been interpreted from seismic reflection records. High resolution seismic surveys have definitely indicated gas hydrate distributions, and drilling the MITI Nankai Trough wells in 2000 and the METI Tokai-oki to Kumano-nada wells in 2004 have revealed subsurface gas hydrate in the eastern part of Nankai Trough. In 1998 and 2002 Mallik wells were drilled at Mackenzie Delta in the Canadian Arctic that also clarified the characteristics of gas hydrate-dominant sandy layers at depths from 890 to 1110 m beneath the permafrost zone. During the field operations, the LWD and wire-line well log data were continuously obtained and plenty of gas hydrate-bearing sand cores were recovered. Subsequence sedimentological and geochemical analyses performed on those core samples revealed the crucial geologic controls on the formation and preservation of natural gas hydrate in sediments. Pore-space gas hydrates reside in sandy sediments mostly filling intergranular porosity. Pore waters chloride anomalies, core temperature depression and core observations on visible gas hydrates confirm the presence of pore-space gas hydrates within moderate to thick sandy layers, typically 10 cm to a meter thick. Sediment porosities and pore-size distributions were obtained by mercury porosimetry, which indicate that porosities of gas hydrate-bearing sandy strata are approximately 45 %. According to grain size distribution curves, gas hydrate is dominant in fine- to very fine-grained sandy strata. Gas hydrate saturations are typically up to 80 % in pore volume throughout most of the hydrate-dominant sandy layers, which are estimated by well log analyses as well as pore water chloride anomalies. It is necessary for investigating subsurface fluid flow behaviors to evaluate both porosity and permeability of gas hydrate-bearing sandy sediments, and the measurements of water permeability for them indicated that highly saturated

  10. Operating experience with gas-bearing circulators in a high-pressure helium loop

    Sanders, J.P.; Gat, U.; Young, H.C.

    1988-01-01

    A high-pressure engineering test loop has been designed and constructed at the Oak Ridge National Laboratory for circulating helium through a test chamber at temperatures to 1,000 deg. C. The purpose of this loop is to determine the thermal and structural performance of proposed components for the primary loops of gas-cooled nuclear reactors. Three gas-bearing circulators, mounted in series, provide a maximum volumetric flow of 0.47 m 3 /s and a maximum head of 78 kJ/kg at operating pressures from 0.1 to 10.7 MPa. Control of gaseous impurities in the circulating gas was the significant operating requirement that dictated the choice of a circulator that is lubricated by the circulating gas. The motor for each circulator is contained within the pressure boundary, and it is cooled by circulating the gas in the motor cavity over water-cooled coils. Each motor is rated at 200 kW at a speed of 23,500 rpm. The circulators have been operated in the loop for more than 5,000 h. The flow of the gas in the loop is controlled by varying the speed of the circulators through the use of individual 250-kVA, solid state power supplies that can be continuously varied in frequency from 50 to 400 Hz. To prevent excessive wear on the gas bearings during startup, the circulator motor accelerates the rotor to 3,000 rpm in less than one second. During operation, no problems associated with the gas bearings, per se, were encountered; however, related problems pointed to design considerations that should be included in future applications of circulators of this type. The primary test that has been conducted in this loop required sustained operation for several weeks without interruption. After a number of unscheduled interruptions, the operating goals were attained. During part of this period, the loop was operated with only two circulators installed in the pressure vessels with a guard installed in the third vessel to protect the closure flange from the gas temperatures. Unattended

  11. Linear and Non-Linear Control Techniques Applied to Actively Lubricated Journal Bearings

    Nicoletti, Rodrigo; Santos, Ilmar

    2003-01-01

    The main objectives of actively lubricated bearings are the simultaneous reduction of wear and vibration between rotating and stationary machinery parts. For reducing wear and dissipating vibration energy until certain limits, one can count with the conventional hydrodynamic lubrication. For furt......The main objectives of actively lubricated bearings are the simultaneous reduction of wear and vibration between rotating and stationary machinery parts. For reducing wear and dissipating vibration energy until certain limits, one can count with the conventional hydrodynamic lubrication....... For further reduction of shaft vibrations one can count with the active lubrication action, which is based on injecting pressurised oil into the bearing gap through orifices machined in the bearing sliding surface. The design and efficiency of some linear (PD, PI and PID) and non-linear controllers, applied...... vibration reduction of unbalance response of a rigid rotor, where the PD and the non-linear P controllers show better performance for the frequency range of study (0 to 80 Hz). The feasibility of eliminating rotor-bearing instabilities (phenomena of whirl) by using active lubrication is also investigated...

  12. Experimental analysis of a rigid rotor supported on aerodynamic foil journal bearings

    Arghir M.

    2014-01-01

    Full Text Available Aerodynamic foil bearings are highly non linear components used or intending to be used for supporting high speed rotors (>30 krpm of low size rotating machines (<400 kW. The non linear character comes from the highly deformable structure of the bearing made of thin steel sheets and from the Coulomb friction forces arising during dynamic displacements. The present work shows the non linear response of a rigid rotor supported by a pair of such bearings and entrained at 82 krpm. The measurements performed during the coast down revealed sub synchronous and asynchronous vibrations of the rotor and their multiples. A simplified theoretical model reproduces qualitatively some of these non linear characteristics.

  13. Design Optimization of Tilting-Pad Journal Bearing Using a Genetic Algorithm

    Hamit Saruhan

    2004-01-01

    Full Text Available This article focuses on the use of genetic algorithms in developing an efficient optimum design method for tilting pad bearings. The approach optimizes based on minimum film thickness, power loss, maximum film temperature, and a global objective. Results for a five tilting-pad preloaded bearing are presented to provide a comparison with more traditional optimum design methods such as the gradient-based global criterion method, and also to provide insight into the potential of genetic algorithms in the design of rotor bearings. Genetic algorithms are efficient search techniques based on the idea of natural selection and genetics. These robust methods have gained recognition as general problem solving techniques in many applications.

  14. Nonlinear Analysis of Rotors Supported by Air Foil Journal Bearings – Theory and Experiments

    Larsen, Jon Steffen

    with a good margin of rotordynamical stable operation. To ensure this, good mathematical models, capable of accurately predicting the dynamic behaviour of the rotor-bearing system, are required at the design stage. This thesis focuses on developing and improving existing mathematical models for predicting...... mechanical behaviour of the bump foils was carefully examined. A mathematical model capable of predicting this nonlinear behaviour was developed and compared to the experimental results with good agreement. With the second test rig, the overall nonlinear behaviour of the rotor-bearing system was investigated...

  15. Quantitative monitoring of gas flooding in oil-bearing reservoirs using a pulsed neutron tool

    Ruhovets, N.; Wyatt, D.F. Jr.

    1991-01-01

    This paper reports on quantitative monitoring of gas flooding in oil bearing reservoirs which is unique in that saturations of three fluids (gas, oil and water) in the effective pore space have to be determined, while in most other applications saturation behind casing is determined only for two fluids: hydrocarbons and water. A new method has been developed to monitor gas flooding of oil reservoirs. The method is based on computing two porosities: true effective (base) porosity determined before gas flooding, and apparent effective (monitor) porosity determined after gas flooding. The base porosity is determined from open and/or cased hole porosity logs run before the flooding. When open hole logs are available, the cased hole porosity logs are calibrated against open hole log. The monitor porosity is determined from one of the cased hole porosity logs, such as a neutron log or count rate ratio curve from a pulsed neutron log run after the gas flooding. The base and monitor porosities provide determination of the hydrogen index of the reservoir fluid after the flooding. This hydrogen index is then used to determine saturation of the flood agent after flooding. Water saturation after flooding can be determined from the equation which relates neutron total cross section (Σm) to volumetric constituent cross sections, using Σm values from a monitor run (after flooding)

  16. A constitutive mechanical model for gas hydrate bearing sediments incorporating inelastic mechanisms

    Sánchez, Marcelo

    2016-11-30

    Gas hydrate bearing sediments (HBS) are natural soils formed in permafrost and sub-marine settings where the temperature and pressure conditions are such that gas hydrates are stable. If these conditions shift from the hydrate stability zone, hydrates dissociate and move from the solid to the gas phase. Hydrate dissociation is accompanied by significant changes in sediment structure and strongly affects its mechanical behavior (e.g., sediment stiffenss, strength and dilatancy). The mechanical behavior of HBS is very complex and its modeling poses great challenges. This paper presents a new geomechanical model for hydrate bearing sediments. The model incorporates the concept of partition stress, plus a number of inelastic mechanisms proposed to capture the complex behavior of this type of soil. This constitutive model is especially well suited to simulate the behavior of HBS upon dissociation. The model was applied and validated against experimental data from triaxial and oedometric tests conducted on manufactured and natural specimens involving different hydrate saturation, hydrate morphology, and confinement conditions. Particular attention was paid to model the HBS behavior during hydrate dissociation under loading. The model performance was highly satisfactory in all the cases studied. It managed to properly capture the main features of HBS mechanical behavior and it also assisted to interpret the behavior of this type of sediment under different loading and hydrate conditions.

  17. Coupled numerical modeling of gas hydrates bearing sediments from laboratory to field-scale conditions

    Sanchez, M. J.; Santamarina, C.; Gai, X., Sr.; Teymouri, M., Sr.

    2017-12-01

    Stability and behavior of Hydrate Bearing Sediments (HBS) are characterized by the metastable character of the gas hydrate structure which strongly depends on thermo-hydro-chemo-mechanical (THCM) actions. Hydrate formation, dissociation and methane production from hydrate bearing sediments are coupled THCM processes that involve, amongst other, exothermic formation and endothermic dissociation of hydrate and ice phases, mixed fluid flow and large changes in fluid pressure. The analysis of available data from past field and laboratory experiments, and the optimization of future field production studies require a formal and robust numerical framework able to capture the very complex behavior of this type of soil. A comprehensive fully coupled THCM formulation has been developed and implemented into a finite element code to tackle problems involving gas hydrates sediments. Special attention is paid to the geomechanical behavior of HBS, and particularly to their response upon hydrate dissociation under loading. The numerical framework has been validated against recent experiments conducted under controlled conditions in the laboratory that challenge the proposed approach and highlight the complex interaction among THCM processes in HBS. The performance of the models in these case studies is highly satisfactory. Finally, the numerical code is applied to analyze the behavior of gas hydrate soils under field-scale conditions exploring different features of material behavior under possible reservoir conditions.

  18. Micromechanical investigation of sand migration in gas hydrate-bearing sediments

    Uchida, S.; Klar, A.; Cohen, E.

    2017-12-01

    Past field gas production tests from hydrate bearing sediments have indicated that sand migration is an important phenomenon that needs to be considered for successful long-term gas production. The authors previously developed the continuum based analytical thermo-hydro-mechanical sand migration model that can be applied to predict wellbore responses during gas production. However, the model parameters involved in the model still needs to be calibrated and studied thoroughly and it still remains a challenge to conduct well-defined laboratory experiments of sand migration, especially in hydrate-bearing sediments. Taking the advantage of capability of micromechanical modelling approach through discrete element method (DEM), this work presents a first step towards quantifying one of the model parameters that governs stresses reduction due to grain detachment. Grains represented by DEM particles are randomly removed from an isotropically loaded DEM specimen and statistical analyses reveal that linear proportionality exists between the normalized volume of detached solids and normalized reduced stresses. The DEM specimen with different porosities (different packing densities) are also considered and statistical analyses show that there is a clear transition between loose sand behavior and dense sand behavior, characterized by the relative density.

  19. Gas Bearing Control for Safe Operation in Critical Speed Regions - Experimental Verification

    Theisen, Lukas R. S.; Niemann, Hans H.; Galeazzi, Roberto

    2015-01-01

    supported by gas bearings to extend their operating range. Using H∞-design methods, active lubrication techniques are proposed to enhance the damping, which in turn reduces the vibrations to a desired safe level. The control design is validated experimentally on a laboratory test rig, and shown to allow...... and deceleration patterns and avoidance of operation near the critical speeds, which is a limiting factor during operation, specially during run-downs. An approach for reducing the vibrations is by feedback controlled lubrication. This paper addresses the challenge of reducing vibrations in rotating machines...

  20. Authigenic rhodochrosite from a gas hydrate-bearing structure in Lake Baikal

    Krylov, Alexey A.; Hachikubo, Akihiro; Minami, Hirotsugu; Pogodaeva, Tatyana V.; Zemskaya, Tamara I.; Krzhizhanovskaya, Mariya G.; Poort, Jeffrey; Khlystov, Oleg M.

    2018-02-01

    Early diagenetic carbonates are rare in Lake Baikal. Siderite (Fe carbonate) concretions in the sediments were discovered only recently. Here, we discuss the first finding of rhodochrosite concretions (Mn carbonate) discovered in the near-bottom sediments of the gas hydrate-bearing seepage structure St. Petersburg-2 in the deep water environment of the Central Baikal Basin. The crystal lattice of rhodochrosite contains iron and calcium substituting to manganese. Based on pore water geochemistry and of δ 13C values of rhodochrosite (- 23.3 and - 29.4‰), carbon dioxide (+ 3.8 to - 16.1‰) and methane (- 63.2 to - 67.8‰), we show that carbonate crystallization most likely occurred during microbial anaerobic oxidation of organic matter, and that part of the oxygen making up the rhodochrosite seems to be derived from the 18O-rich water released from dissociating gas hydrates.

  1. Stability Analysis of an Industrial Gas Compressor Supported by Tilting-Pad Bearings Under Different Lubrication Regimes

    Cerda, Alejandro; Santos, Ilmar

    2012-01-01

    This work is aimed at a theoretical study of the dynamic behavior of a rotor-tilting pad journal bearing (TPJB) system under different lubrication regimes, namely, thermohydrodynamic (THD), elastohydrodynamic (EHD), and hybrid lubrication regime. The rotor modeled corresponds to an industrial com...

  2. Polyethylene glycol drilling fluid for drilling in marine gas hydrates-bearing sediments: an experimental study

    Jiang, G.; Liu, T.; Ning, F.; Tu, Y.; Zhang, L.; Yu, Y.; Kuang, L. [China University of Geosciences, Faculty of Engineering, Wuhan (China)

    2011-07-01

    Shale inhibition, low-temperature performance, the ability to prevent calcium and magnesium-ion pollution, and hydrate inhibition of polyethylene glycol drilling fluid were each tested with conventional drilling-fluid test equipment and an experimental gas-hydrate integrated simulation system developed by our laboratory. The results of these tests show that drilling fluid with a formulation of artificial seawater, 3% bentonite, 0.3% Na{sub 2}CO{sub 3}, 10% polyethylene glycol, 20% NaCl, 4% SMP-2, 1% LV-PAC, 0.5% NaOH and 1% PVP K-90 performs well in shale swelling and gas hydrate inhibition. It also shows satisfactory rheological properties and lubrication at temperature ranges from -8 {sup o}C to 15 {sup o}C. The PVP K-90, a kinetic hydrate inhibitor, can effectively inhibit gas hydrate aggregations at a dose of 1 wt%. This finding demonstrates that a drilling fluid with a high addition of NaCl and a low addition of PVP K-90 is suitable for drilling in natural marine gas-hydrate-bearing sediments. (authors)

  3. Polyethylene Glycol Drilling Fluid for Drilling in Marine Gas Hydrates-Bearing Sediments: An Experimental Study

    Lixin Kuang

    2011-01-01

    Full Text Available Shale inhibition, low-temperature performance, the ability to prevent calcium and magnesium-ion pollution, and hydrate inhibition of polyethylene glycol drilling fluid were each tested with conventional drilling-fluid test equipment and an experimental gas-hydrate integrated simulation system developed by our laboratory. The results of these tests show that drilling fluid with a formulation of artificial seawater, 3% bentonite, 0.3% Na2CO3, 10% polyethylene glycol, 20% NaCl, 4% SMP-2, 1% LV-PAC, 0.5% NaOH and 1% PVP K-90 performs well in shale swelling and gas hydrate inhibition. It also shows satisfactory rheological properties and lubrication at temperature ranges from −8 °C to 15 °C. The PVP K-90, a kinetic hydrate inhibitor, can effectively inhibit gas hydrate aggregations at a dose of 1 wt%. This finding demonstrates that a drilling fluid with a high addition of NaCl and a low addition of PVP K-90 is suitable for drilling in natural marine gas-hydrate-bearing sediments.

  4. Anisotropic permeable porous facing and slip velocity on squeeze film in an axially undefined journal bearing with ferrofluid lubricant

    Shah, R.C.; Bhat, M.V.

    2004-01-01

    Ferrofluid squeeze film in an axially undefined porous journal bearing was analyzed to determine its performance considering anisotropic permeability of the porous facing and slip velocity at the interface of porous matrix and film region using Jenkins flow model. Expressions were obtained for dimensionless pressure, load capacity and response time of the squeeze film. How to deduce results for no-slip case, isotropic porous case and for Neuringer-Rosensweig model case were indicated. The computed values of dimensionless load capacity and response time were displayed in graphical form. They increased with increasing values of eccentricity ratio and anisotropic parameter while they decreased with increasing values of slip parameter or material parameter of Jenkins model

  5. Lateral vibration control of a flexible overcritical rotor via an active gas bearing – Theoretical and experimental comparisons

    Pierart Vásquez, Fabián Gonzalo; Santos, Ilmar

    2016-01-01

    The lack of damping of radial gas bearings leads to high vibration levels of a rotor supported by this type of bearing when crossing resonant areas. This is even more relevant for flexible rotors, as studied in this work. In order to reduce these high vibration levels, an active gas bearing...... is proposed. The control action of this active bearing is selected based on two different strategies: a simple proportional integral derivative controller and an optimal controller. Both controllers are designed based on a theoretical model previously presented. The dynamics of the flexible rotor are modelled......-based controllers are compared against experimental results, showing good agreement. Theoretical and experimental results show a significant increase in the damping ratio of the system, enabling the flexible rotor to run safely across the critical speeds and up to 12,000rev/min, i.e. 50 percent over the second...

  6. Petrology of the Devonian gas-bearing shale along Lake Erie helps explain gas shows

    Broadhead, R.F.; Potter, P.E.

    1980-11-01

    Comprehensive petrologic study of 136 thin sections of the Ohio Shale along Lake Erie, when combined with detailed stratigraphic study, helps explain the occurrence of its gas shows, most of which occur in the silty, greenish-gray, organic poor Chagrin Shale and Three Lick Bed. Both have thicker siltstone laminae and more siltstone beds than other members of the Ohio Shale and both units also contain more clayshales. The source of the gas in the Chagrin Shale and Three Lick Bed of the Ohio Shale is believed to be the bituminous-rich shales of the middle and lower parts of the underlying Huron Member of the Ohio Shale. Eleven petrographic types were recognized and extended descriptions are provided of the major ones - claystones, clayshales, mudshales, and bituminous shales plus laminated and unlaminated siltstones and very minor marlstones and sandstones. In addition three major types of lamination were identified and studied. Thirty-two shale samples were analyzed for organic carbon, whole rock hydrogen and whole rock nitrogen with a Perkin-Elmer 240 Elemental Analyzer and provided the data base for source rock evaluation of the Ohio Shale.

  7. Friction and Wear Reduction of Eccentric Journal Bearing Made of Sn-Based Babbitt for Ore Cone Crusher.

    Amanov, Auezhan; Ahn, Byungmin; Lee, Moon Gu; Jeon, Yongho; Pyun, Young-Sik

    2016-11-22

    An anti-friction Babbitt alloy-coated bearing made by a casting process is a journal bearing, which is used in an ore cone crusher eccentric. The main purpose of the Babbitt coated eccentric is to provide a low friction to support and guide a rotating shaft. Despite the fact that the Babbitt-coated eccentric offers a low friction coefficient and can be operated without a continuous supply of lubricant, it suffers from mining environments and short service life. In this study, an ultrasonic nanocrystalline surface modification (UNSM) technique was used to further reduce the friction coefficient, to increase the wear resistance, and to extend the service life of the Sn-based Babbitt metal. The friction and wear behavior of the Sn-based Babbitt metal was investigated using a block-on-ring tester under both dry and oil-lubricated conditions. The results of the experiments revealed that the friction and wear behavior of Sn-based Babbitt metal could be improved by the application of the UNSM technique. The friction and wear mechanisms of the specimens were explained and discussed in terms of changes in surface properties-microstructure, surface hardness, surface roughness, etc.

  8. Friction and Wear Reduction of Eccentric Journal Bearing Made of Sn-Based Babbitt for Ore Cone Crusher

    Auezhan Amanov

    2016-11-01

    Full Text Available An anti-friction Babbitt alloy-coated bearing made by a casting process is a journal bearing, which is used in an ore cone crusher eccentric. The main purpose of the Babbitt coated eccentric is to provide a low friction to support and guide a rotating shaft. Despite the fact that the Babbitt-coated eccentric offers a low friction coefficient and can be operated without a continuous supply of lubricant, it suffers from mining environments and short service life. In this study, an ultrasonic nanocrystalline surface modification (UNSM technique was used to further reduce the friction coefficient, to increase the wear resistance, and to extend the service life of the Sn-based Babbitt metal. The friction and wear behavior of the Sn-based Babbitt metal was investigated using a block-on-ring tester under both dry and oil-lubricated conditions. The results of the experiments revealed that the friction and wear behavior of Sn-based Babbitt metal could be improved by the application of the UNSM technique. The friction and wear mechanisms of the specimens were explained and discussed in terms of changes in surface properties—microstructure, surface hardness, surface roughness, etc.

  9. Passive magnetic bearing configurations

    Post, Richard F [Walnut Creek, CA

    2011-01-25

    A journal bearing provides vertical and radial stability to a rotor of a passive magnetic bearing system when the rotor is not rotating and when it is rotating. In the passive magnetic bearing system, the rotor has a vertical axis of rotation. Without the journal bearing, the rotor is vertically and radially unstable when stationary, and is vertically stable and radially unstable when rotating.

  10. Numerical Simulation and Experimental Study on the Gas-Solid Coupling of the Aerostatic Thrust Bearing with Elastic Equalizing Pressure Groove

    Zhao Xiao-long

    2017-01-01

    Full Text Available Aiming at the problem of low stiffness of aerostatic bearing, according to the principle of gas-solid coupling, this paper designs a kind of aerostatic thrust bearing with elastic equalizing pressure groove (EEPG and investigates the effect of elastic equalizing pressure groove (EEPG on the stiffness of aerostatic bearing. According to the physical model of the bearing, one deduces the deformation control equation of the elastic equalizing pressure groove and the control equation of gas lubrication, using finite difference method to derive the control equations and coupling calculation. The bearing capacity and stiffness of aerostatic bearing with EEPG in different gas film clearance are obtained. The calculation results show that the stiffness increased by 59%. The results of numerical calculation and experimental results have good consistency, proving the gas-solid coupling method can improve the bearing stiffness.

  11. Tribaloy alloy reinforced tin-bronze composite coating for journal bearing applications

    Gao, F.; Liu, R.; Wu, X.J.

    2011-01-01

    This article presents an experimental study of the tribological behavior of a tin/bronze-based composite coating. The improved-ductility Tribaloy alloy (T-401) particles are selected as the reinforcement. This coating is made on the bushing of planet journals used in aerospace engines, deposited with the high velocity oxygen fuel (HVOF) thermal spray technique. The tribological properties such as friction and wear resistance of the coated bushing are investigated under the WAMsc3 Sliding Contact Test, along with the leaded tin/bronze bushing tested for comparison. The testing results show that the bushing coated with the composite exhibits superior tribological properties to the leaded tin/bronze bushing in that the former runs longer before the friction coefficient reaches 0.5 and also leads a to lower wear rate than the latter. The experimental results and wear mechanisms of these two bushings are discussed with the assistance of worn surface analyses using scanning electron microscopy (SEM).

  12. Comparative Performance of a Non-recessed Hole-entry Hybrid/Hydrostatic Conical Journal Bearing Compensated with Capillary and Orifice Restrictors

    P.G. Khakse

    2016-06-01

    Full Text Available This research paper deals with the theoretical study of comparison of capillary and orifice compensated non-recess hole-entry hydrostatic/ hybrid conical journal bearing. Modified Reynolds equation governing the flow of lubricant in the clearance space of conical journal and bearing has been solved using FEM, Newton-Raphson method and Gauss elimination method. Spherical coordinate system has been employed to obtain the results. The results have been computed for uniform distribution of holes in the circumferential direction with the range of restrictor design parameter C ̅_s2 = 0.02 - 0.1. The numerically simulated result shows, the use of orifice restrictor is to increase bearing stiffness, threshold speed and maximum pressure compared to capillary restrictor for applied radial load.

  13. Effects of Attenuation of Gas Hydrate-bearing Sediments on Seismic Data: Example from Mallik, Northwest Territories, Canada

    Bellefleur, G.; Riedel, M.; Brent, T.

    2007-05-01

    Wave attenuation is an important physical property of hydrate-bearing sediments that is rarely taken into account in site characterization with seismic data. We present a field example showing improved images of hydrate- bearing sediments on seismic data after compensation of attenuation effects. Compressional quality factors (Q) are estimated from zero-offset Vertical Seismic Profiling data acquired at Mallik, Northwest Territories, Canada. During the last 10 years, two internationally-partnered research drilling programs have intersected three major intervals of sub-permafrost gas hydrates at Mallik, and have successfully extracted core samples containing significant amount of gas hydrates. Individual gas hydrate intervals are up to 40m in thickness and are characterized by high in situ gas hydrate saturation, sometimes exceeding 80% of pore volume of unconsolidated clastic sediments having average porosities ranging from 25% to 40%. The Q-factors obtained from the VSP data demonstrate significant wave attenuation for permafrost and hydrate- bearing sediments. These results are in agreement with previous attenuation estimates from sonic logs and crosshole data at different frequency intervals. The Q-factors obtained from VSP data were used to compensate attenuation effects on surface 3D seismic data acquired over the Mallik gas hydrate research wells. Intervals of gas hydrate on surface seismic data are characterized by strong reflectivity and effects from attenuation are not perceptible from a simple visual inspection of the data. However, the application of an inverse Q-filter increases the resolution of the data and improves correlation with log data, particularly for the shallowest gas hydrate interval. Compensation of the attenuation effects of the permafrost likely explains most of the improvements for the shallow gas hydrate zone. Our results show that characterization of the Mallik gas hydrates with seismic data not corrected for attenuation would tend to

  14. Virtual reality application in oil and gas industry | Shammar | Journal ...

    Virtual reality application in oil and gas industry. ... is the key factor for considering AR as an effective tool to be used in maintenance work. Works related to applications of VR for energy exploration and safety training for petroleum industry is ...

  15. Grain-scale imaging and compositional characterization of cryo-preserved India NGHP 01 gas-hydrate-bearing cores

    Stern, Laura A.; Lorenson, T.D.

    2014-01-01

    We report on grain-scale characteristics and gas analyses of gas-hydrate-bearing samples retrieved by NGHP Expedition 01 as part of a large-scale effort to study gas hydrate occurrences off the eastern-Indian Peninsula and along the Andaman convergent margin. Using cryogenic scanning electron microscopy, X-ray spectroscopy, and gas chromatography, we investigated gas hydrate grain morphology and distribution within sediments, gas hydrate composition, and methane isotopic composition of samples from Krishna–Godavari (KG) basin and Andaman back-arc basin borehole sites from depths ranging 26 to 525 mbsf. Gas hydrate in KG-basin samples commonly occurs as nodules or coarse veins with typical hydrate grain size of 30–80 μm, as small pods or thin veins 50 to several hundred microns in width, or disseminated in sediment. Nodules contain abundant and commonly isolated macropores, in some places suggesting the original presence of a free gas phase. Gas hydrate also occurs as faceted crystals lining the interiors of cavities. While these vug-like structures constitute a relatively minor mode of gas hydrate occurrence, they were observed in near-seafloor KG-basin samples as well as in those of deeper origin (>100 mbsf) and may be original formation features. Other samples exhibit gas hydrate grains rimmed by NaCl-bearing material, presumably produced by salt exclusion during original hydrate formation. Well-preserved microfossil and other biogenic detritus are also found within several samples, most abundantly in Andaman core material where gas hydrate fills microfossil crevices. The range of gas hydrate modes of occurrence observed in the full suite of samples suggests a range of formation processes were involved, as influenced by local in situconditions. The hydrate-forming gas is predominantly methane with trace quantities of higher molecular weight hydrocarbons of primarily microbial origin. The composition indicates the gas hydrate is Structure I.

  16. Modified effective medium model for gas hydrate bearing,clay-dominated sediments in the Krishna-Godavari Basin

    Sriram, G.; Dewangan, P.; Ramprasad, T.

    .D., 1990. Nonlinear elasticity and pressure-dependent wave speeds in granular media. Proc. R. Soc. London. Ser. A Math. Phys. Sci. 430, 105–131. Guerin, G., Goldberg, D., 2005. Modeling of acoustic wave dissipation in gas hydrate-bearing sediments...

  17. Toward the problem of oil and gas bearing capacity of the East Tom-Kolyvan structural zone (Western Siberia)

    Stolbova, N F; Maerkov, P O

    2014-01-01

    The vast depression in the east Tom-Kolyvan folded zone (West Siberia) has been identified by the geophysical data. The well which uncovered 4000 m deep profile of the Jurassic and Paleozoic deposits has been drilled. The relevance of the research is the oil/gas-bearing capacity evaluation of the discovered depression in this West Siberia area

  18. Chaos and bifurcation of a flexible rotor supported by porous squeeze couple stress fluid film journal bearings with non-linear suspension

    Chang-Jian, C.-W.; Chen, C.-K.

    2008-01-01

    This study presents a dynamic analysis of a flexible rotor supported by two porous squeeze couple stress fluid film journal bearings with non-linear suspension. The dynamics of the rotor center and bearing center are studied. The analysis of the rotor-bearing system is investigated under the assumptions of non-Newtonian fluid and a short bearing approximation. The spatial displacements in the horizontal and vertical directions are considered for various non-dimensional speed ratios. The dynamic equations are solved using the Runge-Kutta method. The analysis methods employed in this study is inclusive of the dynamic trajectories of the rotor center and bearing center, power spectra, Poincare maps and bifurcation diagrams. The maximum Lyapunov exponent analysis is also used to identify the onset of chaotic motion. The numerical results show that the stability of the system varies with the non-dimensional speed ratios, the non-dimensional parameter l* and the permeability. The modeling results thus obtained by using the method proposed in this paper can be employed to predict the stability of the rotor-bearing system and the undesirable behavior of the rotor and bearing center can be avoided

  19. Determination of the full characteristics of a journal bearing for a fast reactor sodium pump using a full scale model bearing operating in water

    Gilroy, J.E.; Dostal, M.; Jones, R.P.

    1988-01-01

    This paper describes the analytical and experimental work carried out in support of a sodium-lubricated hydrostatic bearing for the CDFR primary sodium pump. The principle objective of the work was to establish bearing characteristics under steady-state and transient running conditions. A knowledge of these characteristics is necessary for the determination of the dynamic performance of the pump under normal and transient operating conditions and also under earthquake loading conditions

  20. Comparison of Physical Properties of Marine and Arctic Gas-Hydrate-Bearing Deposits

    Winters, W. J.; Walker, M.; Collett, T. S.; Bryant, S. L.; Novosel, I.; Wilcox-Cline, R.; Bing, J.; Gomes, M. L.

    2009-12-01

    Gas hydrate (GH) occurs in both marine settings and in arctic environments within a wide variety of sediment types. Grain-size analyses from both environments indicate that intrinsic host-sediment properties have a strong influence on gas-hydrate distribution and morphologic characteristics. Depending on the amount formed or dissociated, gas hydrate can significantly change in situ sediment acoustic, mechanical, and hydraulic properties. The U.S. Geological Survey, in cooperation with the U.S. Dept. of Energy, BP Expl.-Alaska, Nat. GH Prog. of India, Canadian Geological Survey, Int. Ocean Drilling Program, Japan Oil Gas and Metals Nat. Corp., Japan Pet. Expl. Co., Int. Marine Past Global Changes Study (IMAGES) program, and Paleoceanography of the Atlantic and Geochemistry (PAGE) program, determined physical properties from marine and arctic sediments and their relation to the presence of GH. At two arctic sites, the Mount Elbert well on the Alaskan North Slope and the Mallik wells on the Mackenzie Delta, NWT, >10-m thick gas-hydrate-bearing (GHB) sandy deposits are capped by finer-grained sediments that may reduce gas migration. In the Mount Elbert well, average median grain sizes (MGS) for the two thickest GHB deposits are 65 and 60 µm. Finer-grained (average MGS of 9 and 28 µm) sediments have plug permeabilities that are 300 and 14 times smaller than underlying GHB sediment. Average MGS of GHB sediment from the Mallik 2L well is ~ 111 µm, compared to overlying sediment with an average MGS of ~ 32 µm. Gas hydrate morphology in the Gulf of Mexico (GOM) and offshore India is substantially more complex than in the arctic, and is related to pervasive, although not exclusive, finer-grained deposits. Massive, several-cm thick, GH layers were recovered in piston cores in the northern GOM, in sediment with little visible lithologic variability (average MGS ~ 0.8 µm). In wells off the east coast of India, GH was present in sand-rich, fractured clay, and reservoirs

  1. Comparison of Two Classifiers; K-Nearest Neighbor and Artificial Neural Network, for Fault Diagnosis on a Main Engine Journal-Bearing

    A. Moosavian

    2013-01-01

    Full Text Available Vibration analysis is an accepted method in condition monitoring of machines, since it can provide useful and reliable information about machine working condition. This paper surveys a new scheme for fault diagnosis of main journal-bearings of internal combustion (IC engine based on power spectral density (PSD technique and two classifiers, namely, K-nearest neighbor (KNN and artificial neural network (ANN. Vibration signals for three different conditions of journal-bearing; normal, with oil starvation condition and extreme wear fault were acquired from an IC engine. PSD was applied to process the vibration signals. Thirty features were extracted from the PSD values of signals as a feature source for fault diagnosis. KNN and ANN were trained by training data set and then used as diagnostic classifiers. Variable K value and hidden neuron count (N were used in the range of 1 to 20, with a step size of 1 for KNN and ANN to gain the best classification results. The roles of PSD, KNN and ANN techniques were studied. From the results, it is shown that the performance of ANN is better than KNN. The experimental results dèmonstrate that the proposed diagnostic method can reliably separate different fault conditions in main journal-bearings of IC engine.

  2. Oil and gas planning and development in Alberta : new approaches to integrate grizzly bear conservation

    Stenhouse, G. [Foothills Model Forest Grizzly Bear Research Program, AB (Canada)

    2007-07-01

    This paper reported on a grizzly bear research program that was initiated in the province of Alberta to provide new knowledge and tools to ensure the long term survival of grizzly bears on a multiple use landscape. The Foothills Model Forest (FMF) Grizzly Bear Research Program was formed by scientists from across Canada from a variety of scientific disciplines. A strong partner base has been created to allow the FMF's research efforts to span the entire current distribution of grizzly bear habitat in Alberta. The FMF has provided new large scale seamless maps of grizzly bear habitat and, using detailed grizzly bear GPS movement data, has constructed and tested models that can identify key grizzly bear habitat. This presentation focused on the results of 9 years of applied research and described the new tools and models that are now available to program partners in Alberta. The products are currently being used by both industry and government in Alberta as new standards in landscape management planning in grizzly bear habitat. The author suggested that the approach taken with grizzly bears in Alberta could be used and adapted for a variety of wildlife species in the north. figs.

  3. An Assessment of Gas Foil Bearing Scalability and the Potential Benefits to Civilian Turbofan Engines

    Bruckner, Robert J.

    2010-01-01

    Over the past several years the term oil-free turbomachinery has been used to describe a rotor support system for high speed turbomachinery that does not require oil for lubrication, damping, or cooling. The foundation technology for oil-free turbomachinery is the compliant foil bearing. This technology can replace the conventional rolling element bearings found in current engines. Two major benefits are realized with this technology. The primary benefit is the elimination of the oil lubrication system, accessory gearbox, tower shaft, and one turbine frame. These components account for 8 to 13 percent of the turbofan engine weight. The second benefit that compliant foil bearings offer to turbofan engines is the capability to operate at higher rotational speeds and shaft diameters. While traditional rolling element bearings have diminished life, reliability, and load capacity with increasing speeds, the foil bearing has a load capacity proportional to speed. The traditional applications for foil bearings have been in small, lightweight machines. However, recent advancements in the design and manufacturing of foil bearings have increased their potential size. An analysis, grounded in experimentally proven operation, is performed to assess the scalability of the modern foil bearing. This analysis was coupled to the requirements of civilian turbofan engines. The application of the foil bearing to larger, high bypass ratio engines nominally at the 120 kN (approx.25000 lb) thrust class has been examined. The application of this advanced technology to this system was found to reduce mission fuel burn by 3.05 percent.

  4. An effective medium inversion algorithm for gas hydrate quantification and its application to laboratory and borehole measurements of gas hydrate-bearing sediments

    Chand, S.; Minshull, T.A.; Priest, J.A.; Best, A.I.; Clayton, C.R.I.; Waite, W.F.

    2006-01-01

    The presence of gas hydrate in marine sediments alters their physical properties. In some circumstances, gas hydrate may cement sediment grains together and dramatically increase the seismic P- and S-wave velocities of the composite medium. Hydrate may also form a load-bearing structure within the sediment microstructure, but with different seismic wave attenuation characteristics, changing the attenuation behaviour of the composite. Here we introduce an inversion algorithm based on effective medium modelling to infer hydrate saturations from velocity and attenuation measurements on hydrate-bearing sediments. The velocity increase is modelled as extra binding developed by gas hydrate that strengthens the sediment microstructure. The attenuation increase is modelled through a difference in fluid flow properties caused by different permeabilities in the sediment and hydrate microstructures. We relate velocity and attenuation increases in hydrate-bearing sediments to their hydrate content, using an effective medium inversion algorithm based on the self-consistent approximation (SCA), differential effective medium (DEM) theory, and Biot and squirt flow mechanisms of fluid flow. The inversion algorithm is able to convert observations in compressional and shear wave velocities and attenuations to hydrate saturation in the sediment pore space. We applied our algorithm to a data set from the Mallik 2L–38 well, Mackenzie delta, Canada, and to data from laboratory measurements on gas-rich and water-saturated sand samples. Predictions using our algorithm match the borehole data and water-saturated laboratory data if the proportion of hydrate contributing to the load-bearing structure increases with hydrate saturation. The predictions match the gas-rich laboratory data if that proportion decreases with hydrate saturation. We attribute this difference to differences in hydrate formation mechanisms between the two environments.

  5. Forecasting sandstone uranium deposits in oil-and-gas bearing basins

    Pechenkin, I.

    2014-01-01

    The interrelation between oxidation and reduction processes in the carbonaceous strata of Paleogene age was first studied in the 1950s in deposit of the Fergana depression. The presence of pre-ore and post-ore epigenesis of petroleum series was established. Part of uranium mineralization was found to be covered with fluid oil. In the middle of the 1960s in the Sabirsay deposit (Uzbekistan) in primary red-coloured continental sediment of Cretaceous age were studied pre-ore reduction changes, which caused economic uranium mineralization in contrasting geochemical barrier. Further research showed that multidirectional epigenetic processes had changed repeatedly. Later, in the 1970s, American geologists studying uranium deposits in the oil-and-gas bearing Texas Plain reached similar conclusions. From their point of view, in the Benevides deposit the main zones of mineralization tend to be located near the boundary where the zones of oxidation in the strata wedge in, developing in epigenetically reduced formations. A second post-mineral reduction was registered in a number of rock bodies. The complexity of the processes is determined by the double role of hydrocarbon fluids and the products of their dissolution. On the one hand, bituminization of permeable strata as well as pyritization, chloritization, dolomitization and other alterations associated with it create favourable geochemical conditions of a reducing character for a subsequent concentration of ore and nonmetal raw materials. On the other hand, intrusion of bitumen and its dissolution in the aeration zone leads to the burial of the mineralization which formed earlier and disappearance of all traces of its formation (epigenetic oxidation zoning). Thus forecasting and subsequent prospecting become impeded. The established sequence of epigenetic alterations allows us to carry out specialized mapping in productive regions, uncovering hidden parts of epigenetic oxidation zoning and “buried” mineralization

  6. Experimental investigations of active air bearings

    Santos, Ilmar; Morosi, Stefano

    2012-01-01

    Along with traditional oil lubrication, increasing demand for high-speed applications has renewed attention to gas bearings technology. Traditional aerostatic and aerodynamic gas lubrication has been widely used in a variety of applications, ranging from high-speed spindles to micro and meso......-scale turbomachinery. The present paper deals with experimental rotordynamic testing of a flexible rotor supported by hybrid aerostaticaerodynamic gas journal bearing equipped with an electronic radial air injection system. From a rotordynamic point of view there are two phenomena that limit the widespread...... of traditional gas lubrication: 1) Low damping makes operation across critical speed dangerous, as even low level of unbalance can generate large vibration responses. This is especially problematic for gas bearing applications, which often operate in the supercritical region. Moreover, 2) An upper bound...

  7. Dissolution of cemented fractures in gas bearing shales in the context of CO2 sequestration

    Kwiatkowski, Kamil; Szymczak, Piotr

    2016-04-01

    varying from 0.2 x 0.2 m2 up to 4 x 4 m2, together with discussion of a further upscaling, make the study relevant to the industrial applications. While the results of this study should be applicable to different shale formations throughout the world, we discuss them in the context of preparation to gas-production from Pomeranian shale basin, located in the northern Poland. [1] Mosher, K., He, J., Liu, Y., Rupp, E., & Wilcox, J. Molecular simulation of methane adsorption in micro-and mesoporous carbons with applications to coal and gas shale systems. International Journal of Coal Geology, 109, 36-44 (2013) [2] Grieser, W. V., Wheaton, W. E., Magness, W. D., Blauch, M. E., & Loghry, R, "Surface Reactive Fluid's Effect on Shale." Proceedings of the Production and Operations Symposium, 31 March-3 April 2007, Oklahoma City (SPE-106815-MS) [3] Tao, Z. and Clarens, A., Estimating the carbon sequestration capacity of shale formations using methane production rates, Environmental Science and Technology, 47, 11318-11325 (2013). [4] Zhang, X., Jeffrey, R. G., & Thiercelin, M. (2009). Mechanics of fluid-driven fracture growth in naturally fractured reservoirs with simple network geometries. Journal of Geophysical Research: Solid Earth, 114, B12406 (2009) [5] Gale, J.F., Laubach, S.E., Olson, J.E., Eichhubl, P., Fall, A. Natural fractures in shale: A review and new observations. AAPG Bulletin 98(11):2165-2216 (2014)

  8. In situ thermal conductivity of gas-hydrate-bearing sediments of the Mallik 5L-38 well

    Henninges, J.; Huenges, E.; Burkhardt, H.

    2005-11-01

    Detailed knowledge about thermal properties of rocks containing gas hydrate is required in order to quantify processes involving gas hydrate formation and decomposition in nature. In the framework of the Mallik 2002 program, three wells penetrating a continental gas hydrate occurrence under permafrost were successfully equipped with permanent fiber-optic distributed temperature sensing cables. Temperature data were collected over a 21-month period after completing the wells. Thermal conductivity profiles were calculated from the geothermal data as well as from a petrophysical model derived from the available logging data and application of mixing law models. Results indicate that thermal conductivity variations are mainly lithologically controlled with a minor influence from hydrate saturation. Average thermal conductivity values of the hydrate-bearing sediments range between 2.35 and 2.77 W m-1 K-1. Maximum gas hydrate saturations can reach up to about 90% at an average porosity of 0.3.

  9. Program for tests on magnetic bearing suspended rotor dynamics for gas turbine high temperature reactor (GTHTR300)

    Takada, Shoji; Takizuka, Takakazu; Kunitomi, Kazuhiko; Kosugiyama, Shinichi; Yan, Xing

    2003-01-01

    A program for test on rotor dynamics was planned for the turbo-machine of the Gas Turbine High Temperature Reactor (GTHTR300). The rotor system of the turbo-machine consists of a turbo-compressor rotor and a generator rotor connected with a flexible coupling, each suspended with two radial magnetic bearings. The rotors, which are flexible rotors, pass over the critical speeds of bending mode. The magnetic bearing is required to have a high load capacity, about 10 times larger than any built thus far to support a flexible rotor. In the rotor design, the standard limit of the vibration amplitude of 75 μm at the rated rotational speed of 3,600 rpm was fulfilled by optimizing the stiffness of the magnetic bearings. A test apparatus was designed to verify the design of the magnetic bearing suspended turbo-machine rotor of the GTHTR300. The test apparatus is composed of 1/3-scale test rotors, which are connected with a flexible coupling and driven by a variable speed motor. The test magnetic bearing was designed within the state-of-the-art technology to have a load capacity about 1/10 of that of the actual one. The test rotors were designed to closely simulate the critical speeds and vibration modes of the actual ones. This paper shows the test apparatus and the test plan for the magnetic bearing suspended rotor system. The present study is entrusted from the Ministry of Education, Culture, Sports, Science and Technology of Japan. (author)

  10. Faunal communities at sites of gas- and oil-bearing fluids in Lake Baikal

    Zemskaya, Tamara I.; Sitnikova, Tatiana Y.; Kiyashko, Sergei I.; Kalmychkov, Gennady V.; Pogodaeva, Tatiana V.; Mekhanikova, Irina V.; Naumova, Tatiana V.; Shubenkova, Olga V.; Chernitsina, Svetlana M.; Kotsar, Oleg V.; Chernyaev, Evgeny S.; Khlystov, Oleg M.

    2012-12-01

    Macro- and meiofaunal communities were examined at four geomorphologically distinct sites with different gas- and oil-bearing fluid characteristics in the northern, central and southern basins of Lake Baikal. All sites had elevated concentrations of bicarbonate, nitrate, sulphate and chloride ions in pore fluids, with highest values at the Frolikha vent. Elevated levels of iron ions were found in pore waters of the St. Petersburg methane seep and the Gorevoy Utes oil seep. The chemical composition of pore waters at the Malenky mud volcano was similar to that reported in earlier work. Consistent with published data, the Frolikha vent (northern basin) and the St. Petersburg methane seep (central basin) were characterised by methane of mixed genesis (thermogenic + biogenic), whereas the methane source was mainly thermogenic at the Gorevoy Utes oil seep (central basin) and biogenic at the Malenky mud volcano (southern basin). In contrast to marine seep ecosystems, the macrofauna was dominated only by amphipods, giant planarians and oligochaetes, whereas bivalves were absent; the meiofauna was similar to its marine counterpart, being dominated by nematodes, cyclops, harpacticoids and ostracods. A statistically significant positive relationship was revealed between faunal abundance and the availability of bacterial mats on seep sediments. Moreover, ANOVA tests showed significant increases in both meiozoobenthic and macrozoobenthic densities at "hot spot" vent/seep sites relative to discharge-free reference sites. The isotopic composition of carbon and nitrogen at various trophic levels of these benthic vent/seep communities was found to differ markedly from that reported by earlier studies for the pelagic and other benthic food webs in Lake Baikal. As in marine seeps, the macrofauna had variable isotopic signatures. Light δ13C and δ15N values suggest the utilization of chemosynthetically fixed and/or methane-derived organic matter. By contrast, the heavy δ13C

  11. On the Controllability and Observability of Actively Lubricated Journal Bearings with Pads Featuring Different Nozzle-Pivot Configurations

    Salazar, Jorge Andrés González; Santos, Ilmar

    2017-01-01

    tilt angle, (iii) the vertical pad movement-due to the pivot flexibility, and (iv) the controllable force as the hydraulic DOF. The test rig consists of a rigid rotor supported by a single rocker-pivoted rigid pad. A thorough parametric study is carried out by investigating the effects of: (a) nozzle-pivot...... offset, (b) pivot flexibility, and (c) bearing loading on these control basics in order to determine the pad with the best control characteristics. Different nozzle-pivot offsets can be set by varying the positioning of either the injection nozzle or the pivot line. The influence of the pivot compliance...... on the bearing dynamics is assessed by benchmarking the results obtained with the flexible pivot against the rigid pivot. Three different bearing loads are studied. According to the results, the proposed configurations, especially the offset-pivot pad with slight offsets, improve the bearing control...

  12. High-resolution well-log derived dielectric properties of gas-hydrate-bearing sediments, Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

    Sun, Y.; Goldberg, D.; Collett, T.; Hunter, R.

    2011-01-01

    A dielectric logging tool, electromagnetic propagation tool (EPT), was deployed in 2007 in the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well (Mount Elbert Well), North Slope, Alaska. The measured dielectric properties in the Mount Elbert well, combined with density log measurements, result in a vertical high-resolution (cm-scale) estimate of gas hydrate saturation. Two hydrate-bearing sand reservoirs about 20 m thick were identified using the EPT log and exhibited gas-hydrate saturation estimates ranging from 45% to 85%. In hydrate-bearing zones where variation of hole size and oil-based mud invasion are minimal, EPT-based gas hydrate saturation estimates on average agree well with lower vertical resolution estimates from the nuclear magnetic resonance logs; however, saturation and porosity estimates based on EPT logs are not reliable in intervals with substantial variations in borehole diameter and oil-based invasion.EPT log interpretation reveals many thin-bedded layers at various depths, both above and below the thick continuous hydrate occurrences, which range from 30-cm to about 1-m thick. Such thin layers are not indicated in other well logs, or from the visual observation of core, with the exception of the image log recorded by the oil-base microimager. We also observe that EPT dielectric measurements can be used to accurately detect fine-scale changes in lithology and pore fluid properties of hydrate-bearing sediments where variation of hole size is minimal. EPT measurements may thus provide high-resolution in-situ hydrate saturation estimates for comparison and calibration with laboratory analysis. ?? 2010 Elsevier Ltd.

  13. Design of multi-input multi-output controller for magnetic bearing which suspends helium gas-turbine generator rotor for high temperature gas cooled reactor

    Takada, Shoji; Funatake, Yoshio; Inagaki, Yoshiyuki

    2009-01-01

    A design of a MIMO controller, which links magnetic forces of multiple magnetic bearings by feedback of multiple measurement values of vibration of a rotor, was proposed for the radial magnetic bearings for the generator rotor of helium gas turbine with a power output of 300 MWe. The generator rotor is a flexible rotor, which passes over the forth critical speed. A controller transfer function was derived at the forth critical speed, in which the bending vibration mode is similar to the one which is excited by unbalance mass to reduce a modeling error. A 1404-dimensional un-symmetric coefficient matrix of equation of state for the rotating rotor affected by Jayro effect was reduced by a modal decomposition using Schur decomposition to reduce a reduction error. The numerical results showed that unbalance response of rotor was 53 and 80 μm p-p , respectively, well below the allowable limits both at the rated and critical speeds. (author)

  14. Sensing sulfur oxides and other sulfur bearing pollutants with solid electrolyte pellets. I. Gas concentration cells

    Chamberland, A M; Gauthier, J M

    1977-01-01

    A new sensing technique using a solid electrolyte has been demonstrated for sulfur-bearing pollutants. Based on potentiometric measurements across a pellet of potassium sulfate, this sensor allows concentrations of sulfur dioxides, sulfur trioxide, hydrogen sulfide, methyl mercaptan and carbonyl sulfide in air to be measured with accuracy. Its operational concentration range at the present time is 0.1 ppM up to at least 10,000 ppM. The presence of other common pollutants such as carbon dioxide, methane, nitric oxide and nitrogen dioxide does not interfere with the measurement of air samples containing sulfur-bearing pollutants.

  15. Hydraulic and Mechanical Effects from Gas Hydrate Conversion and Secondary Gas Hydrate Formation during Injection of CO2 into CH4-Hydrate-Bearing Sediments

    Bigalke, N.; Deusner, C.; Kossel, E.; Schicks, J. M.; Spangenberg, E.; Priegnitz, M.; Heeschen, K. U.; Abendroth, S.; Thaler, J.; Haeckel, M.

    2014-12-01

    The injection of CO2 into CH4-hydrate-bearing sediments has the potential to drive natural gas production and simultaneously sequester CO2 by hydrate conversion. The process aims at maintaining the in situ hydrate saturation and structure and causing limited impact on soil hydraulic properties and geomechanical stability. However, to increase hydrate conversion yields and rates it must potentially be assisted by thermal stimulation or depressurization. Further, secondary formation of CO2-rich hydrates from pore water and injected CO2 enhances hydrate conversion and CH4 production yields [1]. Technical stimulation and secondary hydrate formation add significant complexity to the bulk conversion process resulting in spatial and temporal effects on hydraulic and geomechanical properties that cannot be predicted by current reservoir simulation codes. In a combined experimental and numerical approach, it is our objective to elucidate both hydraulic and mechanical effects of CO2 injection and CH4-CO2-hydrate conversion in CH4-hydrate bearing soils. For the experimental approach we used various high-pressure flow-through systems equipped with different online and in situ monitoring tools (e.g. Raman microscopy, MRI and ERT). One particular focus was the design of triaxial cell experimental systems, which enable us to study sample behavior even during large deformations and particle flow. We present results from various flow-through high-pressure experimental studies on different scales, which indicate that hydraulic and geomechanical properties of hydrate-bearing sediments are drastically altered during and after injection of CO2. We discuss the results in light of the competing processes of hydrate dissociation, hydrate conversion and secondary hydrate formation. Our results will also contribute to the understanding of effects of temperature and pressure changes leading to dissociation of gas hydrates in ocean and permafrost systems. [1] Deusner C, Bigalke N, Kossel E

  16. High Specific Stiffness Shafts and Advanced Bearing Coatings for Gas Turbine Engines Final Report CRADA No. TC-1089-95

    Barbee, Troy [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chin, Herbert [United Technologies Corporation, East Hartford, CT (United States)

    2017-11-09

    At the time of the CRADA, the largest in-service gas-turbine aircraft engines strove for increased thrust and power density to meet the requirements for take-off thrust, given the increase in take-off gross weight (TOGW) associated with longer range transport requirements. The trend in modem turbo shaft engines was toward turbine shafts with higher and higher length-to-diameter ratios, which reduced the shaft critical speed. Using co nventional shaft materials, this lead to shafts that needed to operate near or above sensitive shaft bending critical speeds, therefore requiring multiple bearings and/ or multiple squeeze-film dampers to control the dynamic response. Using new materials and d esign concepts this project demonstrated the use of new shaft materials which could provide increased shaft speed range above existing maximum engine speeds without encountering a critic al speed event and high vector deflections. This increased main shaft speed also resulted in decreased bearing life associated with lower heat dissipation and higher centrifugal forces. Thus, a limited effort was devoted to feasibility of higher performance bearing coatings to mitigate the speed effects.

  17. Hydro-geomechanical behaviour of gas-hydrate bearing soils during gas production through depressurization and CO2 injection

    Deusner, C.; Gupta, S.; Kossel, E.; Bigalke, N.; Haeckel, M.

    2015-12-01

    Results from recent field trials suggest that natural gas could be produced from marine gas hydrate reservoirs at compatible yields and rates. It appears, from a current perspective, that gas production would essentially be based on depressurization and, when facing suitable conditions, be assisted by local thermal stimulation or gas hydrate conversion after injection of CO2-rich fluids. Both field trials, onshore in the Alaska permafrost and in the Nankai Trough offshore Japan, were accompanied by different technical issues, the most striking problems resulting from un-predicted geomechanical behaviour, sediment destabilization and catastrophic sand production. So far, there is a lack of experimental data which could help to understand relevant mechanisms and triggers for potential soil failure in gas hydrate production, to guide model development for simulation of soil behaviour in large-scale production, and to identify processes which drive or, further, mitigate sand production. We use high-pressure flow-through systems in combination with different online and in situ monitoring tools (e.g. Raman microscopy, MRI) to simulate relevant gas hydrate production scenarios. Key components for soil mechanical studies are triaxial systems with ERT (Electric resistivity tomography) and high-resolution local strain analysis. Sand production control and management is studied in a novel hollow-cylinder-type triaxial setup with a miniaturized borehole which allows fluid and particle transport at different fluid injection and flow conditions. Further, the development of a large-scale high-pressure flow-through triaxial test system equipped with μ-CT is ongoing. We will present results from high-pressure flow-through experiments on gas production through depressurization and injection of CO2-rich fluids. Experimental data are used to develop and parametrize numerical models which can simulate coupled process dynamics during gas-hydrate formation and gas production.

  18. EVIDENCE OF CORROSIVE GAS FORMED BY RADIOLYSIS OF CHLORIDE SALTS IN PLUTONIUM-BEARING MATERIALS

    Dunn, K.; Louthan, M.

    2010-02-01

    Corrosion and pitting have been observed in headspace regions of stainless steel containers enclosing plutonium oxide/salt mixtures. These observations are consistent with the formation of a corrosive gas, probably HCl, and transport of that gas to the headspace regions of sealed containers. The NH{sub 4}Cl films found on the walls of the sealed containers is also indicative of the presence of HCl gas. Radiolysis of hydrated alkaline earth salts is the probable source of HCl.

  19. Feasibility of Influencing the Dynamic Fluid Film Coefficients of a Multirecess Journal Bearing by means of Active Hybrid Lubrication

    Santos, Ilmar; Watanabe, F. Y.

    2003-01-01

    and control techniques. The feasibility of influencing the dynamic fluid film coefficients (stiffness and damping) by means of a controllable fluid injection into opposed bearing recesses is investigated. By controlling the pressure and flow injection using servo control systems, it is possible to obtain...

  20. Faulting of gas-hydrate-bearing marine sediments - contribution to permeability

    Dillon, William P.; Holbrook, W.S.; Drury, Rebecca; Gettrust, Joseph; Hutchinson, Deborah; Booth, James; Taylor, Michael

    1997-01-01

    Extensive faulting is observed in sediments containing high concentrations of methane hydrate off the southeastern coast of the United States. Faults that break the sea floor show evidence of both extension and shortening; mud diapirs are also present. The zone of recent faulting apparently extends from the ocean floor down to the base of gas-hydrate stability. We infer that the faulting resulted from excess pore pressure in gas trapped beneath the gas hydrate-beating layer and/or weakening and mobilization of sediments in the region just below the gas-hydrate stability zone. In addition to the zone of surface faults, we identified two buried zones of faulting, that may have similar origins. Subsurface faulted zones appear to act as gas traps.

  1. Electrical Conductive Mechanism of Gas Hydrate-Bearing Reservoirs in the Permafrost Region of Qilian Mountain

    Peng, C.; Zou, C.; Tang, Y.; Liu, A.; Hu, X.

    2017-12-01

    In the Qilian Mountain, gas hydrates not only occur in pore spaces of sandstones, but also fill in fractures of mudstones. This leads to the difficulty in identification and evaluation of gas hydrate reservoir from resistivity and velocity logs. Understanding electrical conductive mechanism is the basis for log interpretation. However, the research is insufficient in this area. We have collected well logs from 30 wells in this area. Well logs and rock samples from DK-9, DK-11 and DK-12 wells were used in this study. The experiments including SEM, thin section, NMR, XRD, synthesis of gas hydrate in consolidated rock cores under low temperature and measurement of their resistivity and others were performed for understanding the effects of pore structure, rock composition, temperature and gas hydrate on conductivity. The results show that the porosity of reservoir of pore filling type is less than 10% and its clay mineral content is high. As good conductive passages, fractures can reduce resistivity of water-saturated rock. If fractures in the mudstone are filled by calcite, resistivity increases significantly. The resistivity of water-saturated rock at 2°C is twice of that at 18°C. The gas hydrate formation process in the sandstone was studied by resistivity recorded in real time. In the early stage of gas hydrate formation, the increase of residual water salinity may lead to the decrease of resistivity. In the late stage of gas hydrate formation, the continuity decrease of water leads to continuity increase of resistivity. In summary, fractures, rock composition, temperature and gas hydrate are important factors influencing resistivity of formation. This study is helpful for more accurate evaluation of gas hydrate from resistivity log. Acknowledgment: We acknowledge the financial support of the National Special Program for Gas Hydrate Exploration and Test-production (GZH201400302).

  2. A constitutive mechanical model for gas hydrate bearing sediments incorporating inelastic mechanisms

    Sá nchez, Marcelo; Gai, Xuerui; Santamarina, Carlos

    2016-01-01

    , hydrates dissociate and move from the solid to the gas phase. Hydrate dissociation is accompanied by significant changes in sediment structure and strongly affects its mechanical behavior (e.g., sediment stiffenss, strength and dilatancy). The mechanical

  3. Foil Gas Bearing Supported Quiet Fan for Spacecraft Ventilation, Phase I

    National Aeronautics and Space Administration — Developing a quiet fan for Environmental Control and Life Support systems to enhance the livable environment within the spacecraft has been a challenge. A Foil Gas...

  4. Gas emissions from mining voids in Lorraine iron-bearing basin

    Grabowski, D.; Pokryszka, Z.

    2003-01-01

    A study carried out in the iron basin of Lorraine (France) put the spot on the existence of under-oxygenated and noxious gas emissions (carbon dioxide, radon..) in built-up areas related to former mining works. Site investigations showed that the gas flow was mainly due to natural ventilation mechanisms. A further study is in progress in order to better understand the origin of the atmosphere modification within the old mine workings. (authors)

  5. Methane sources in gas hydrate-bearing cold seeps: Evidence from radiocarbon and stable isotopes

    Pohlman, J.W.; Bauer, J.E.; Canuel, E.A.; Grabowski, K.S.; Knies, D.L.; Mitchell, C.S.; Whiticar, Michael J.; Coffin, R.B.

    2009-01-01

    Fossil methane from the large and dynamic marine gas hydrate reservoir has the potential to influence oceanic and atmospheric carbon pools. However, natural radiocarbon (14C) measurements of gas hydrate methane have been extremely limited, and their use as a source and process indicator has not yet been systematically established. In this study, gas hydrate-bound and dissolved methane recovered from six geologically and geographically distinct high-gas-flux cold seeps was found to be 98 to 100% fossil based on its 14C content. Given this prevalence of fossil methane and the small contribution of gas hydrate (??? 1%) to the present-day atmospheric methane flux, non-fossil contributions of gas hydrate methane to the atmosphere are not likely to be quantitatively significant. This conclusion is consistent with contemporary atmospheric methane budget calculations. In combination with ??13C- and ??D-methane measurements, we also determine the extent to which the low, but detectable, amounts of 14C (~ 1-2% modern carbon, pMC) in methane from two cold seeps might reflect in situ production from near-seafloor sediment organic carbon (SOC). A 14C mass balance approach using fossil methane and 14C-enriched SOC suggests that as much as 8 to 29% of hydrate-associated methane carbon may originate from SOC contained within the upper 6??m of sediment. These findings validate the assumption of a predominantly fossil carbon source for marine gas hydrate, but also indicate that structural gas hydrate from at least certain cold seeps contains a component of methane produced during decomposition of non-fossil organic matter in near-surface sediment.

  6. Dynamic Testing with the NSWC Three-Degree-of-Freedom Gas Bearing

    1982-03-08

    Long Island, NY 11714 Mr. J. W. Faust 1 A . Martellucci 1 Marquardt Aircraft W. Daskin 1 Corporation J. D. Cresawll 1 16555 Saticoy Street J. Pettus 1...BEARING S. PERFORMING ORG. REPORT MUMMER 7. AUTHOR( a ) S. CONTRACT OR GRANT NUMUERia) F. J. REGAN S. PERFORMING ORGANIZATION NAME AND ADDRESS1.PRGA...ADDRESS 12. REPORT DATE 8 march 1982 1S. NUMBER OF PAGES 19’ MONITORING AGENCY NAME A ADDRESS(’lIf 0"#t bW CmoUIMd Office) 15. SECURITY CLASS. (Of Nil

  7. Measurement and calculation of dynamic coefficients in hydrodynamic bearings of gas films; Medicion y calculo de coeficientes dinamicos en cojinetes hidrodinamicos de peliculas de gas

    Ruiz, Rafael O.; Di Liscia, Marcelo H.; Diaz, Sergio E. [Universidad Simon Bolivar, Sartendejas, Baruta (Venezuela)

    2007-11-15

    The identification of the dynamic coefficients in air bearings is fundamental for a suitable roto-dynamic analysis. The present paper shows the development of an algorithm that allows the direct obtaining of the dynamic coefficients in hydrodynamic air bearings as much of numerical form as experimental. The testing bench used consists of two magnetic bearings, which support the rotor in their ends and work as well as actuators allowing inducing controlled orbits in the rotor. The test bearing is located between the magnetic bearings. The dynamic forces generated in the air bearing are registered from three load cells. The algorithm was developed in a commercial code of graphical programming, through which the signals can be collected, controlled and processed. The nonlinear behavior of this type of bearings makes difficult the calculation of the dynamic coefficients, therefore the processing of the signals in frequencial space facilitates, in a certain way, its handling. On the other hand, the numerical model was compared with the experimental results obtaining acceptable approaches in magnitude as well as in behavior. The numerical dynamic coefficients calculation was realized solving the Reynolds differential equation for a compressible fluid in the thickness of the gas film, taking into consideration the fluid mass flow that is introduced, as well as the pressure loss suffered by the same in passing through the feeding orifices. The numerical methods utilized include the solution of the differential equation of Reynolds for finite differences, the calculation of the profile realizing successive iterations and the calculation of the hydrodynamics forces through the Simpson numerical integration. The numerical dynamic coefficients were found applying a minimum squared technique to the hydrodynamic stresses generated in simulating an orbit of the rotor at a determined frequency and velocity, allowing in this way the calculation of the synchronous and asynchronous

  8. Noble gases in common rocks and their bearing on noble gas occurrences in the hydrological cycle

    Mazor, E.

    1978-10-01

    The comparison of the noble gases contents in different rocks and in thermal and cold water sources in the French Massif Central was aimed to define the amounts and nature of noble gases contributed by country rocks as opposed to atmospheric noble gases brought in by recharged water. No difference in the noble gas contents was found between waters coming in igneous rocks to those issuing in sedimentary rocks. In both, significant variations in the contents of atmospheric and radiogenic noble gases were found. Radiogenic helium has been found to reveal a positive correlation to the contents of atmospheric Ne, Ar, Kr. This indicates water recharge into the deep part of the systems, mixing with radiogenic He and Ar flushed from igneous and sedimentary rocks and subsequent partial gas loss. Loss of gas is evident from the observed low noble gas contents. These losses have been accompanied by a reversed retention pattern of Ne, Ar, Xc. This reversed retention pattern cannot be an artifact of sampling as well as cannot result by partial steam loss. A similar interpretation for the observed noble gas depletions that agrees with the fact that the observed fractionation patterns are not ''normal'' is given by deuterium and oxygen-18. The stable isotope data seem to exclude partial steam losses

  9. Pressurized subsampling system for pressured gas-hydrate-bearing sediment: Microscale imaging using X-ray computed tomography

    Jin, Yusuke; Konno, Yoshihiro; Nagao, Jiro

    2014-01-01

    A pressurized subsampling system was developed for pressured gas hydrate (GH)-bearing sediments, which have been stored under pressure. The system subsamples small amounts of GH sediments from cores (approximately 50 mm in diameter and 300 mm in height) without pressure release to atmospheric conditions. The maximum size of the subsamples is 12.5 mm in diameter and 20 mm in height. Moreover, our system transfers the subsample into a pressure vessel, and seals the pressure vessel by screwing in a plug under hydraulic pressure conditions. In this study, we demonstrated pressurized subsampling from artificial xenon-hydrate sediments and nondestructive microscale imaging of the subsample, using a microfocus X-ray computed tomography (CT) system. In addition, we estimated porosity and hydrate saturation from two-dimensional X-ray CT images of the subsamples

  10. Design of Active Magnetic Bearing Controllers for Rotors Subjected to Gas Seal Forces

    Lauridsen, Jonas Skjødt; Santos, Ilmar F.

    2018-01-01

    Proper design of feedback controllers is crucial for ensuring high performance of Active Magnetic Bearing (AMB) supported rotor dynamic systems. Annular seals in those systems can contribute with significant forces, which, in many cases, are hard to model in advance due to complex geometries...... of the seal and multiphase fluids. Hence, it can be challenging to design AMB controllers that will guarantee robust performance for these kinds of systems. This paper demonstrates the design, simulation and experimental results of model based controllers for AMB systems, subjected to dynamic seal forces....... The controllers are found using H-infinity - and µ synthesis and are based on a global rotor dynamic model in-which the seal coefficients are identified in-situ. The controllers are implemented in a rotor-dynamic test facility with two radial AMBs and one annular seal with an adjustable inlet pressure. The seal...

  11. Forecasting of reservoir pressures of oil and gas bearing complexes in northern part of West Siberia for safety oil and gas deposits exploration and development

    Gorbunov, P. A.; Vorobyov, S. V.

    2017-10-01

    In the paper the features of reservoir pressures changes in the northern part of West Siberian oil-and gas province are described. This research is based on the results of hydrodynamic studies in prospecting and explorating wells in Yamal-Nenets Autonomous District. In the Cenomanian, Albian, Aptian and in the top of Neocomian deposits, according to the research, reservoir pressure is usually equal to hydrostatic pressure. At the bottom of the Neocomian and Jurassic deposits zones with abnormally high reservoir pressures (AHRP) are distinguished within Gydan and Yamal Peninsula and in the Nadym-Pur-Taz interfluve. Authors performed the unique zoning of the territory of the Yamal-Nenets Autonomous District according to the patterns of changes of reservoir pressures in the section of the sedimentary cover. The performed zoning and structural modeling allow authors to create a set of the initial reservoir pressures maps for the main oil and gas bearing complexes of the northern part of West Siberia. The results of the survey should improve the efficiency of exploration drilling by preventing complications and accidents during this operation in zones with abnormally high reservoir pressures. In addition, the results of the study can be used to estimate gas resources within prospective areas of Yamal-Nenets Autonomous District.

  12. Recycling of Zinc- and Lead-Bearing Residues with Pyrolysis Gas

    Pichler, C.; Antrekowitsch, J.

    2015-09-01

    Efforts in the metallurgical industry for an approximation to the zero waste concept has led to many different investigations. Together with the greenhouse effect, CO2 emissions have caused additional costs for different process steps in the industry. For this reason, alternative carbon carriers have been sought, and charcoal was found to be an ideal substitute, due to its CO2 neutrality. In order to use it in the metallurgical industry, an optimization of the charcoal production through a carbonization process must be carried out. Beside the charcoal, pyrolysis gas also occurs during the heating of wood or agricultural wastes under the exclusion of air. Because of combustible compounds in this gas, it is possible to use it as a reduction agent instead of fossil carbon carriers. Together with the idea of preventing landfilling of metallurgical by-products, an investigation was carried out to treat zinc- and lead-containing materials. For this issue a special process concept was designed and developed. The main aspect was to recycle the zinc- and lead-containing Waelz slag, which results from the processing of steel mill dusts, in a vertical retort. Two different sizes of facilities were constructed to perform the reaction system of the solid Waelz slag with the gaseous reduction agent of pyrolysis gas.

  13. Delineating gas bearing reservoir by using spectral decomposition attribute: Case study of Steenkool formation, Bintuni Basin

    Haris, A.; Pradana, G. S.; Riyanto, A.

    2017-07-01

    Tectonic setting of the Bird Head Papua Island becomes an important model for petroleum system in Eastern part of Indonesia. The current exploration has been started since the oil seepage finding in Bintuni and Salawati Basin. The biogenic gas in shallow layer turns out to become an interesting issue in the hydrocarbon exploration. The hydrocarbon accumulation appearance in a shallow layer with dry gas type, appeal biogenic gas for further research. This paper aims at delineating the sweet spot hydrocarbon potential in shallow layer by applying the spectral decomposition technique. The spectral decomposition is decomposing the seismic signal into an individual frequency, which has significant geological meaning. One of spectral decomposition methods is Continuous Wavelet Transform (CWT), which transforms the seismic signal into individual time and frequency simultaneously. This method is able to make easier time-frequency map analysis. When time resolution increases, the frequency resolution will be decreased, and vice versa. In this study, we perform low-frequency shadow zone analysis in which the amplitude anomaly at a low frequency of 15 Hz was observed and we then compare it to the amplitude at the mid (20 Hz) and the high-frequency (30 Hz). The appearance of the amplitude anomaly at a low frequency was disappeared at high frequency, this anomaly disappears. The spectral decomposition by using CWT algorithm has been successfully applied to delineate the sweet spot zone.

  14. The impact of hydrogen-bearing gas to change indexes of car engine in operating conditions

    Korpach A.

    2016-08-01

    Full Text Available Due to lower oil and petroleum products there is a constant problem of the growing use of alternative fuels. One of the most promising is hydrogen, but its use as a self-fuel is rather difficult, but using as the form of supplements has prospects for widespread use in road transport. In order to establish the effectiveness of its use as a hydrogen-containing gas as a product of the electrolysis of the alkaline solution, a series of tests conducted. Tests were carried out on the car ZAZ–1102 "Tavria", which is equipped with an engine MeMZ–245 with carburetor feed system and electrolyser SuperKit 10, which is powered by the vehicle electrical system. At the same time also used electrolytic League–02. The effect on fuel economy additives hydrogen-containing gas to the air charge is determined when the engine is idling. When using additives 1,34 % interest, from the weight of the fuel, fuel efficiency has increased by 1,9 %.

  15. Sulfur-Bearing Phases Detected by Evolved Gas Analysis of the Rocknest Aeolian Deposit, Gale Crater, Mars

    Mcadam, Amy Catherine; Franz, Heather Bryant

    2014-01-01

    The Sample Analysis at Mars (SAM) instrument suite detected SO2, H2S, OCS, and CS2 from approx.450 to 800 C during evolved gas analysis (EGA) of materials from the Rocknest aeolian deposit in Gale Crater, Mars. This was the first detection of evolved sulfur species from a Martian surface sample during in situ EGA. SO2(approx. 3-22 micro-mol) is consistent with the thermal decomposition of Fe sulfates or Ca sulfites, or evolution/desorption from sulfur-bearing amorphous phases. Reactions between reduced sulfur phases such as sulfides and evolved O2 or H2O in the SAM oven are another candidate SO2 source. H2S (approx.41-109 nmol) is consistent with interactions of H2O, H2 and/or HCl with reduced sulfur phases and/or SO2 in the SAM oven. OCS (approx.1-5 nmol) and CS2(approx.0.2-1 nmol) are likely derived from reactions between carbon-bearing compounds and reduced sulfur. Sulfates and sulfites indicate some aqueous interactions, although not necessarily at the Rocknest site; Fe sulfates imply interaction with acid solutions whereas Ca sulfites can form from acidic to near-neutral solutions. Sulfides in the Rocknest materials suggest input from materials originally deposited in a reducing environment or from detrital sulfides from an igneous source. The presence of sulfides also suggests that the materials have not been extensively altered by oxidative aqueous weathering. The possibility of both reduced and oxidized sulfur compounds in the deposit indicates a nonequilibrium assemblage. Understanding the sulfur mineralogy in Rocknest materials, which exhibit chemical similarities to basaltic fines analyzed elsewhere on Mars, can provide insight in to the origin and alteration history of Martian surface materials.

  16. Electrical anisotropy of gas hydrate-bearing sand reservoirs in the Gulf of Mexico

    Cook, Anne E.; Anderson, Barbara I.; Rasmus, John; Sun, Keli; Li, Qiming; Collett, Timothy S.; Goldberg, David S.

    2012-01-01

    We present new results and interpretations of the electricalanisotropy and reservoir architecture in gashydrate-bearingsands using logging data collected during the Gulf of MexicoGasHydrate Joint Industry Project Leg II. We focus specifically on sandreservoirs in Hole Alaminos Canyon 21 A (AC21-A), Hole Green Canyon 955 H (GC955-H) and Hole Walker Ridge 313 H (WR313-H). Using a new logging-while-drilling directional resistivity tool and a one-dimensional inversion developed by Schlumberger, we resolve the resistivity of the current flowing parallel to the bedding, R| and the resistivity of the current flowing perpendicular to the bedding, R|. We find the sandreservoir in Hole AC21-A to be relatively isotropic, with R| and R| values close to 2 Ω m. In contrast, the gashydrate-bearingsandreservoirs in Holes GC955-H and WR313-H are highly anisotropic. In these reservoirs, R| is between 2 and 30 Ω m, and R| is generally an order of magnitude higher. Using Schlumberger's WebMI models, we were able to replicate multiple resistivity measurements and determine the formation resistivity the gashydrate-bearingsandreservoir in Hole WR313-H. The results showed that gashydrate saturations within a single reservoir unit are highly variable. For example, the sand units in Hole WR313-H contain thin layers (on the order of 10-100 cm) with varying gashydrate saturations between 15 and 95%. Our combined modeling results clearly indicate that the gashydrate-bearingsandreservoirs in Holes GC955-H and WR313-H are highly anisotropic due to varying saturations of gashydrate forming in thin layers within larger sand units.

  17. FUNDAMENTALS OF STRUCTURAL TYPOLOGY DEVICE DESIGN WITH A GAS BEARING LAYER

    I. A. Аvtsinоv

    2015-01-01

    Full Text Available We describe the typical stages of a structural typology of devices allowing them to design quality in the automatic mode on the known parameters of products (parts and the required processing operations with them. In the first stage classification it was organized as a piece of specific products and devices for the manipulation of the latter. Specifics items described their physical – mechanical properties, geometry and their application. The most frequently described specific products are used in pharmaceutical, perfume, food, microelectronics, electrical engineering, electronics. The main elements of the proposed device is a carrier working surface over which a thin layer of gas is created. Depending on the position (horizontal or vertical of the form of its movement (rotation, rotational – translational or is stationary, and the configuration of the carrier operating the surface implement various manufacturing operations (targeting, positioning, shaping, classification, transport, heat treatment, weight control, assembly, culling, and others. The second stage was to mathematically describe the relationship of the specificity of piece goods, with design features of devices supporting the work surface and sold them operations. For this purpose, the device has been used in discrete mathematics, with which you can produce a description of all types of devices, and then make a conclusion such as the work surface meets the specified requirements. The apparent advantage of using predicate logic to this problem is fairly simple implementation of the algorithm of structural typology, which can be expressed using a declarative programming language. In the third phase, work is underway to create the necessary algorithmic language program "Prolog" and presented the structure of the imperative and declarative implementation of the algorithm.

  18. A Literature Survey to Identify Potentially Volatile Iodine-Bearing Species Present in Off-Gas Streams

    Bruffey, S. H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Spencer, B. B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Strachan, D. M. [Strata-G, Knoxville, TN (United States); Jubin, R. T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Soelberg, N. R. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Riley, B. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-06-30

    Four radionuclides have been identified as being sufficiently volatile in the reprocessing of nuclear fuel that their gaseous release needs to be controlled to meet regulatory requirements (Jubin et al. 2011, 2012). These radionuclides are 3H, 14C, 85Kr, and 129I. Of these, 129I has the longest half-life and potentially high biological impact. Accordingly, control of the release of 129I is most critical with respect to the regulations for the release of radioactive material in stack emissions. It is estimated that current EPA regulations (EPA 2010) would require any reprocessing plant in the United States to limit 129I release to less than 0.05 Ci/MTIHM for a typical fuel burnup of 55 gigawatt days per metric tonne (GWd/t) (Jubin 2011). The study of inorganic iodide in off-gas systems has been almost exclusively limited to I2 and the focus of organic iodide studies has been CH3I. In this document, we provide the results of an examination of publically available literature that is relevant to the presence and sources of both inorganic and organic iodine-bearing species in reprocessing plants. We especially focus on those that have the potential to be poorly sequestered with traditional capture methodologies. Based on the results of the literature survey and some limited thermodynamic modeling, the inorganic iodine species hypoiodous acid (HOI) and iodine monochloride (ICl) were identified as potentially low-sorbing iodine species that could present in off-gas systems. Organic species of interest included both short chain alkyl iodides such as methyl iodide (CH3I) and longer alkyl iodides up to iodododecane (C10H21I). It was found that fuel dissolution may provide conditions conducive to HOI formation and has been shown to result in volatile long-chain alkyl iodides, though these may not volatilize until later in the reprocessing sequence. Solvent extraction processes were found to be significant sources of various organic iodine-bearing species; formation of these

  19. Experimental contribution to the study of gas bearings; Contribution experimentale a l'etude des paliers a gaz

    Gobert, G

    1962-07-01

    Developments for gas-lubricated bearings are discussed. The study of how the fluid film behaves compared to what one can expect is discussed. Various devices are described which have allowed us to go up to peripheral velocity greater than 400 m/s, leading to rotational speed of several thousand revolutions per second. This is obtained by using an automatic setting for the distance between fixed and rotating walls. (author) [French] Le present travail debute par un apercu de l'etat actuel des connaissances sur le processus de la lubrification, notamment sur les paliers a lubrification par gaz. Apres une analyse effectuee au moyen des recentes theories de R. Comolet sur le film fluide entre disques paralleles, nous decrivons des machines dont les charges axiales et radiales specialement etudiees ont permis, au moyen d'un reglage automatique des jeux entre parois fixes et parois tournantes, d'atteindre des vitesses peripheriques superieures a 400 m/s correspondant a des vitesses de plusieurs milliers de tours par seconde. (auteur)

  20. Experimental contribution to the study of gas bearings; Contribution experimentale a l'etude des paliers a gaz

    Gobert, G

    1962-07-01

    Developments for gas-lubricated bearings are discussed. The study of how the fluid film behaves compared to what one can expect is discussed. Various devices are described which have allowed us to go up to peripheral velocity greater than 400 m/s, leading to rotational speed of several thousand revolutions per second. This is obtained by using an automatic setting for the distance between fixed and rotating walls. (author) [French] Le present travail debute par un apercu de l'etat actuel des connaissances sur le processus de la lubrification, notamment sur les paliers a lubrification par gaz. Apres une analyse effectuee au moyen des recentes theories de R. Comolet sur le film fluide entre disques paralleles, nous decrivons des machines dont les charges axiales et radiales specialement etudiees ont permis, au moyen d'un reglage automatique des jeux entre parois fixes et parois tournantes, d'atteindre des vitesses peripheriques superieures a 400 m/s correspondant a des vitesses de plusieurs milliers de tours par seconde. (auteur)

  1. Abundances of Volatile - Bearing Species from Evolved Gas Analysis of Samples from the Rocknest Aeolian Bedform in Gale Crater

    Archer, P. D., Jr.; Franc, H. B.; Sutter, B.; McAdam, A.; Ming, D. W.; Morris, R. V.; Mahaffy, P. R.

    2013-01-01

    The Sample Analysis at Mars (SAM) instrument suite on board the Mars Science Laboratory (MSL) recently ran four samples from an aeolian bedform named Rocknest. SAM detected the evolution of H2O, CO2, O2, and SO2, indicative of the presence of multiple volatile bearing species (Fig 1). The Rocknest bedform is a windblown deposit selected as representative of both the windblown material in Gale crater as well as the globally-distributed martian dust. Four samples of Rocknest material were analyzed by SAM, all from the fifth scoop taken at this location. The material delivered to SAM passed through a 150 m sieve and is assumed to have been well mixed during the sample acquisition/preparation/handoff process. SAM heated the Rocknest samples to approx.835 C at a ramp rate of 35 C/min with a He carrier gas flow rate of apprx.1.5 standard cubic centimeters per minute and at an oven pressure of 30 mbar [1]. Evolved gases were detected by a quadrupole mass spectrometer (QMS). This abstract presents the molar abundances of H2O, CO2, O2, and SO2 as well as their concentration in rocknest samples using an estimated sample mass.

  2. Estimation of Dry Fracture Weakness, Porosity, and Fluid Modulus Using Observable Seismic Reflection Data in a Gas-Bearing Reservoir

    Chen, Huaizhen; Zhang, Guangzhi

    2017-05-01

    Fracture detection and fluid identification are important tasks for a fractured reservoir characterization. Our goal is to demonstrate a direct approach to utilize azimuthal seismic data to estimate fluid bulk modulus, porosity, and dry fracture weaknesses, which decreases the uncertainty of fluid identification. Combining Gassmann's (Vier. der Natur. Gesellschaft Zürich 96:1-23, 1951) equations and linear-slip model, we first establish new simplified expressions of stiffness parameters for a gas-bearing saturated fractured rock with low porosity and small fracture density, and then we derive a novel PP-wave reflection coefficient in terms of dry background rock properties (P-wave and S-wave moduli, and density), fracture (dry fracture weaknesses), porosity, and fluid (fluid bulk modulus). A Bayesian Markov chain Monte Carlo nonlinear inversion method is proposed to estimate fluid bulk modulus, porosity, and fracture weaknesses directly from azimuthal seismic data. The inversion method yields reasonable estimates in the case of synthetic data containing a moderate noise and stable results on real data.

  3. A bibliographic survey of bearings for nuclear reactors

    Nemoto, Masaaki; Okamoto, Yoshizo

    1977-03-01

    In development of a multi-purpose high-temperature gas cooled reactor, design of its mechanical elements is essential. Machinery must be safely operable in the high temperature (1,000 0 C), high pressure (40kg/cm 2 ) helium environment for long time. A bibliographic review in this connection with technical reports, books, journals and patents, is presented, using NSA. As an element of the machinery bearings are classified into several categories, a bibliography on gas-lubricated bearings for 207 documents is given in chronical order. (auth.)

  4. Application of Crunch-Flow Routines to Constrain Present and Past Carbon Fluxes at Gas-Hydrate Bearing Sites

    Torres, Marta [Oregon State Univ., Corvallis, OR (United States). College of Earth, Ocean, and Atmospheric Sciences

    2014-01-31

    In November 2012, Oregon State University initiated the project entitled: Application of Crunch-Flow routines to constrain present and past carbon fluxes at gas-hydrate bearing sites. Within this project we developed Crunch-Flow based modeling modules that include important biogeochemical processes that need to be considered in gas hydrate environments. Our modules were applied to quantify carbon cycling in present and past systems, using data collected during several DOE-supported drilling expeditions, which include the Cascadia margin in US, Ulleung Basin in South Korea, and several sites drilled offshore India on the Bay of Bengal and Andaman Sea. Specifically, we completed modeling efforts that: 1) Reproduce the compositional and isotopic profiles observed at the eight drilled sites in the Ulleung Basin that constrain and contrast the carbon cycling pathways at chimney (high methane flux) and non-chimney sites (low methane, advective systems); 2) Simulate the Ba record in the sediments to quantify the past dynamics of methane flux in the southern Hydrate Ridge, Cascadia margin; and 3) Provide quantitative estimates of the thickness of individual mass transport deposits (MTDs), time elapsed after the MTD event, rate of sulfate reduction in the MTD, and time required to reach a new steady state at several sites drilled in the Krishna-Godavari (K-G) Basin off India. In addition we developed a hybrid model scheme by coupling a home-made MATLAB code with CrunchFlow to address the methane transport and chloride enrichment at the Ulleung Basins chimney sites, and contributed the modeling component to a study focusing on pore-scale controls on gas hydrate distribution in sediments from the Andaman Sea. These efforts resulted in two manuscripts currently under review, and contributed the modeling component of another pare, also under review. Lessons learned from these efforts are the basis of a mini-workshop to be held at Oregon State University (Feb 2014) to instruct

  5. Magnetic bearings promise reduced operation and maintenance costs

    Jones, G.

    1990-01-01

    Magnetic bearings are being incorporated into the design of the US DoE modular high temperature gas cooled reactor. The virtually maintenance-free bearing technology may have potential in other nuclear applications. In an active magnetic bearing, a stationary electromagnet (stator) and a rotating ferrous material (rotor) are used to allow a shaft to be suspended in a magnetic field. The position of the shaft is maintained dynamically using position sensors to provide a continuous feedback through a control and amplifier system to the electromagnetic poles which are used to suspend the shaft. Two separate systems are required: an axial positioning system, or thrust bearing, and a pair of radial positioning systems, or journal bearings. (author)

  6. Research on dynamics and experiments about auxiliary bearings for the helium circulator of the 10 MW high temperature gas-cooled reactor

    Zhao, Yulan; Yang, Guojun; Liu, Xingnan; Shi, Zhengang; Zhao, Lei

    2016-01-01

    Highlights: • The research in this paper is based on the AMB helium circulator of HTR-10. • The dynamic rotor performance is analyzed by processing experimental data. • The mechanical bearing without lubrication can be applied in the HTR-10 system. - Abstract: The 10 MW high-temperature gas-cooled reactor (HTR-10) was constructed by the Institute of Nuclear and New Energy Technology (INET) of Tsinghua University. The auxiliary bearing is utilized in this system to meet particular requirements for the reactor. The main role of the auxiliary bearing is to constrain rotor displacements and also to support the rotor when the rotor drops down, which is caused by the active magnetic bearing (AMB) failure. The auxiliary bearing needs to endure huge impact, rapid angular acceleration and thermal shock. On the one hand, complex geometrical constructions and forces applied on the system bring difficulties and restrictions to establish an appropriate model to reveal the actual dynamic process. On the other hand, large volumes of data obtained from experiments show velocities and displacements of the rotor during the rotor drop process and then can indicate the actual dynamic interactions to a great extent. The research in this paper is based on the test rig of the AMB helium circulator of HTR-10. This paper aims to analyze the dynamic performance and contact forces of the rotor by processing experimental data. A measurement to estimate forces developed due to impacts of the rotor and the auxiliary bearings is presented. It is of great significance and provides certain foundation to elaborate the rotor drop process for the AMB helium circulator of HTR-10.

  7. Windage Power Loss in Gas Foil Bearings and the Rotor-Stator Clearance of High Speed Generators Operating in High Pressure Environments

    Bruckner, Robert J.

    2009-01-01

    Closed Brayton Cycle (CBC) and Closed Supercritical Cycle (CSC) engines are prime candidates to convert heat from a reactor into electric power for robotic space exploration and habitation. These engine concepts incorporate a permanent magnet starter/generator mounted on the engine shaft along with the requisite turbomachinery. Successful completion of the long-duration missions currently anticipated for these engines will require designs that adequately address all losses within the machine. The preliminary thermal management concept for these engine types is to use the cycle working fluid to provide the required cooling. In addition to providing cooling, the working fluid will also serve as the bearing lubricant. Additional requirements, due to the unique application of these microturbines, are zero contamination of the working fluid and entirely maintenance-free operation for many years. Losses in the gas foil bearings and within the rotor-stator gap of the generator become increasingly important as both rotational speed and mean operating pressure are increased. This paper presents the results of an experimental study, which obtained direct torque measurements on gas foil bearings and generator rotor-stator gaps. Test conditions for these measurements included rotational speeds up to 42,000 revolutions per minute, pressures up to 45 atmospheres, and test gases of nitrogen, helium, and carbon dioxide. These conditions provided a maximum test Taylor number of nearly one million. The results show an exponential rise in power loss as mean operating density is increased for both the gas foil bearing and generator windage. These typical "secondary" losses can become larger than the total system output power if conventional design paradigms are followed. A nondimensional analysis is presented to extend the experimental results into the CSC range for the generator windage.

  8. Recent research and development of bearings for helium circulator

    Taniguchi, S.; Ezaki, Z.; Kawaguchi, K.; Matsumura, N.; Kozima, M.

    1988-01-01

    This paper mainly describes recent studies and successful applications of water lubricated bearing and gas lubricated bearing. Both types of bearing seem to be suitable for a turbo machine installed in an atomic energy plant - such as the helium circulator of a HTGR - not to be affected by radioactivity, so we have been attracted by them for about 10 years. The former was investigated theoretically taking account of turbulent flow due to the low viscosity of water, and compared with the experimental data. Good agreement was obtained, and a successful example applied to a small-sized high speed air compressor is shown. The latter was investigated using a large-sized bearing test rig simulated to an actual machine. The tilting pad journal bearing and the tilting pad thrust bearing were taken and improved for some aspects. These bearings have been taken into service on an actual circulator and are now operating successfully. Currently, a magnetic bearing is being studied to pay special attention to endurance for an earthquake and catcher bearing system. We would like to have an opportunity to present these results in the near future. (author). 5 refs, 15 figs, 2 tabs

  9. Simulation of a multistage fractured horizontal well in a water-bearing tight fractured gas reservoir under non-Darcy flow

    Zhang, Rui-Han; Zhang, Lie-Hui; Wang, Rui-He; Zhao, Yu-Long; Huang, Rui

    2018-06-01

    Reservoir development for unconventional resources such as tight gas reservoirs is in increasing demand due to the rapid decline of production in conventional reserves. Compared with conventional reservoirs, fluid flow in water-bearing tight gas reservoirs is subject to more nonlinear multiphase flow and gas slippage in nano/micro matrix pores because of the strong collisions between rock and gas molecules. Economic gas production from tight gas reservoirs depends on extensive application of water-based hydraulic fracturing of horizontal wells, associated with non-Darcy flow at a high flow rate, geomechanical stress sensitivity of un-propped natural fractures, complex flow geometry and multiscale heterogeneity. How to efficiently and accurately predict the production performance of a multistage fractured horizontal well (MFHW) is challenging. In this paper, a novel multicontinuum, multimechanism, two-phase simulator is established based on unstructured meshes and the control volume finite element method to analyze the production performance of MFHWs. The multiple interacting continua model and discrete fracture model are coupled to integrate the unstimulated fractured reservoir, induced fracture networks (stimulated reservoir volumes, SRVs) and irregular discrete hydraulic fractures. Several simulations and sensitivity analyses are performed with the developed simulator for determining the key factors affecting the production performance of MFHWs. Two widely applied fracturing models, classic hydraulic fracturing which generates long double-wing fractures and the volumetric fracturing aimed at creating large SRVs, are compared to identify which of them can make better use of tight gas reserves.

  10. The Experimental Identification of the Dynamic Coefficients of two Hydrodynamic Journal Bearings Operating at Constant Rotational Speed and Under Nonlinear Conditions

    Breńkacz Łukasz

    2017-12-01

    Full Text Available Hydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm. An impact hammer was used to excite vibration of the shaft. The approximation by means of the least squares method was applied to determine bearing dynamic coefficients. Based on the performed research, the four (i.e. two main and two crosscoupled coefficients of stiffness, damping and mass for each bearing were obtained. The mass coefficients add up to the complex shaft weight. These values are not required for modeling dynamics of the machine because the rotor mass is usually known, however, they may serve as a good indicator to validate the correctness of the stiffness and damping coefficients determined. Additionally, the experimental research procedure was described. The signals of displacements in the bearings and the excitation forces used for determination of the bearing dynamic coefficients were shown. The study discussed in this article is about a rotor supported by two hydrodynamic bearings operating in a nonlinear manner. On the basis of computations, the results of bearing dynamic coefficients were presented for a selected speed.

  11. Bearing system

    Kapich, Davorin D.

    1987-01-01

    A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

  12. Bearing construction for refrigeration compresssor

    Middleton, Marc G.; Nelson, Richard T.

    1988-01-01

    A hermetic refrigeration compressor has a cylinder block and a crankshaft rotatable about a vertical axis to reciprocate a piston in a cylinder on the cylinder block. A separate bearing housing is secured to the central portion of the cylinder block and extends vertically along the crankshaft, where it carries a pair of roller bearings to journal the crankshaft. The crankshaft has a radially extending flange which is journaled by a thrust-type roller bearing above the bearing housing to absorb the vertical forces on the crankshaft so that all three of the roller bearings are between the crankshaft and the bearing housing to maintain and control the close tolerances required by such bearings.

  13. Reservoir characteristics of coal-shale sedimentary sequence in coal-bearing strata and their implications for the accumulation of unconventional gas

    Wang, Yang; Zhu, Yanming; Liu, Yu; Chen, Shangbin

    2018-04-01

    Shale gas and coalbed methane (CBM) are both considered unconventional natural gas and are becoming increasingly important energy resources. In coal-bearing strata, coal and shale are vertically adjacent as coal and shale are continuously deposited. Research on the reservoir characteristics of coal-shale sedimentary sequences is important for CBM and coal-bearing shale gas exploration. In this study, a total of 71 samples were collected, including coal samples (total organic carbon (TOC) content >40%), carbonaceous shale samples (TOC content: 6%-10%), and shale samples (TOC content TOC content. Clay and quartz also have a great effect on the porosity of shale samples. According to the FE-SEM image technique, nanoscale pores in the organic matter of coal samples are much more developed compared with shale samples. For shales with low TOC, inorganic minerals provide more pores than organic matter. In addition, TOC content has a positive relationship with methane adsorption capacity, and the adsorption capacity of coal samples is more sensitive than the shale samples to temperature.

  14. Control system design for flexible rotors supported by actively lubricated bearings

    Nicoletti, Rodrigo; Santos, Ilmar

    2008-01-01

    and keeping the lengths of the two eigenvalues constant in the real-imaginary plane. The methodology is applied to an industrial gas compressor supported by active tilting-pad journal bearings. The unbalance response functions and mode shapes of the flexible rotor with and without active control are presented...

  15. Investigation of the mechanical behaviour of gas-hydrate bearing clayey sediments from the Gulf of Guinea using in-situ geotechnical measurements

    Taleb, F.; Garziglia, S.; Sultan, N.

    2017-12-01

    Expanding needs for energy resources and concerns about climate change have moved industrial and academic interests towards regions where specific thermobaric conditions allow the formation of gas hydrates (GH). While significant advances have been made to characterize the fabric and structure of these metastable geo-compounds, considerable uncertainty remains regarding the impact of their mechanical properties on the seafloor morphology and stability. This is particularly true for gas hydrates-bearing fine-grained sediments, which remain challenging to preserve or synthesise prior to laboratory testing. As a step towards understanding the mechanical consequences of the concentration and distribution of GH in this type of sediments, this work uses acoustic and geotechnical in situ measurements collected in a high gas flux system offshore Nigeria. Acoustic measurements of compressional wave velocity were shown to be convenient means of both detecting and quantifying gas hydrates in marine sediments. Geotechnical data derived from piezocone readings and their distribution in normalised soil classification charts allowed identifying distinct features of gas hydrates-bearing clayey sediments; such as a mechanical behaviour sharing similarities with that of cemented clays. Correlations between acoustic and piezocone data showed that the stiffness and strength tend to generally increase with increasing GH concentrations. However, several sediment intervals sharing the same hydrates concentration have revealed different features of mechanical behaviour. This was linked to the presence of various GH morphologies within the marine sediments such as groups of hydrate veins or massive hydrate nodules. This in-situ approach allowing both understanding the heterogeneous distribution of GH and characterising their host sediment seems key to assess the potential link between seafloor stability and GH dissociation/dissolution caused by human activities or by natural environmental

  16. On the future of controllable fluid film bearings

    Santos, Ilmar

    2011-01-01

    lubrication regimes, i.e., as tilting-pad journal bearings, multi-recess journal bearings and plain journal bearings. After a comprehensive overview of the theoretical and experimental technological advancements achieved in university laboratories, the feasibility of industrial applications is highlighted......This work gives an overview of the theoretical and experimental achievements of mechatronics applied to fluid film bearings. Compressible and uncompressible fluids are addressed. Rigid and elastic (deformable) bearing profiles are investigated. Hydraulic, pneumatic, magnetic and piezoelectric...

  17. A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures.

    Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

    2018-05-01

    The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

  18. A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures

    Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

    2018-05-01

    The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

  19. Neural network analysis of crosshole tomographic images: The seismic signature of gas hydrate bearing sediments in the Mackenzie Delta (NW Canada)

    Bauer, K.; Pratt, R. G.; Haberland, C.; Weber, M.

    2008-10-01

    Crosshole seismic experiments were conducted to study the in-situ properties of gas hydrate bearing sediments (GHBS) in the Mackenzie Delta (NW Canada). Seismic tomography provided images of P velocity, anisotropy, and attenuation. Self-organizing maps (SOM) are powerful neural network techniques to classify and interpret multi-attribute data sets. The coincident tomographic images are translated to a set of data vectors in order to train a Kohonen layer. The total gradient of the model vectors is determined for the trained SOM and a watershed segmentation algorithm is used to visualize and map the lithological clusters with well-defined seismic signatures. Application to the Mallik data reveals four major litho-types: (1) GHBS, (2) sands, (3) shale/coal interlayering, and (4) silt. The signature of seismic P wave characteristics distinguished for the GHBS (high velocities, strong anisotropy and attenuation) is new and can be used for new exploration strategies to map and quantify gas hydrates.

  20. Sulphur-bearing Compounds Detected by MSL SAM Evolved Gas Analysis of Materials from Yellowknife Bay, Gale Crater, Mars

    McAdam, A. C.; Franz, H. B.; Archer, P. D. Jr.; Sutter, B.; Eigenbrode, J. L.; Freissinet, C.; Atreya, S. K.; Bish, D. L.; Blake, D. F.; Brunner, A.; hide

    2014-01-01

    The Sample Analysis at Mars (SAM) and Chemistry and Mineralogy (CheMin) instruments on the Mars Science Laboratory (MSL) analysed several subsamples of sample fines (bearing phases present below the CheMin detection limit or difficult to characterize with XRD (e.g., X-ray amorphous phases). Here, we focus on potential constraints on phases that evolved SO2, H2S, OCS, and CS2 during thermal analysis.

  1. Exergy analysis of a gas turbine power plant | Oko | Journal of ...

    Exergy analysis of a 100MW gas turbine power plant that works on the. Brayton cycle is presented. The average increase in the thermodynamic degradation of the plant over the period of six (6) years at three different levels of load was assessed. The exergy analysis of the plant was done on two sets of data: one from the ...

  2. Laboratory Studies on the Formation of Carbon-Bearing Molecules in Extraterrestrial Environments: From the Gas Phase to the Solid State

    Jamieson, C. S.; Guo, Y.; Gu, X.; Zhang, F.; Bennett, C. J.; Kaiser, R. I.

    2006-01-01

    A detailed knowledge of the formation of carbon-bearing molecules in interstellar ices and in the gas phase of the interstellar medium is of paramount interest to understand the astrochemical evolution of extraterrestrial environments (1). This research also holds strong implications to comprehend the chemical processing of Solar System environments such as icy planets and their moons together with the atmospheres of planets and their satellites (2). Since the present composition of each interstellar and Solar System environment reflects the matter from which it was formed and the processes which have changed the chemical nature since the origin (solar wind, planetary magnetospheres, cosmic ray exposure, photolysis, chemical reactions), a detailed investigation of the physicochemical mechanisms altering the pristine environment is of paramount importance to grasp the contemporary composition. Once these underlying processes have been unraveled, we can identify those molecules, which belonged to the nascent setting, distinguish molecular species synthesized in a later stage, and predict the imminent chemical evolution of, for instance, molecular clouds. Laboratory experiments under controlled physicochemical conditions (temperature, pressure, chemical composition, high energy components) present ideal tools for simulating the chemical evolution of interstellar and Solar System environments. Here, laboratory experiments can predict where and how (reaction mechanisms; chemicals necessary) in extraterrestrial environments and in the interstellar medium complex, carbon bearing molecules can be formed on interstellar grains and in the gas phase. This paper overviews the experimental setups utilized in our laboratory to mimic the chemical processing of gas phase and solid state (ices) environments. These are a crossed molecular beams machine (3) and a surface scattering setup (4). We also present typical results of each setup (formation of amino acids, aldehydes, epoxides

  3. Abundances and implications of volatile-bearing species from evolved gas analysis of the Rocknest aeolian deposit, Gale Crater, Mars

    Archer, Paul Douglas; Franz, Heather B.; Sutter, Brad; Arevalo, Ricardo D.; Coll, Patrice; Eigenbrode, Jennifer L.; Glavin, Daniel P.; Jones, John J.; Leshin, Laurie A.; Mahaffy, Paul R.; McAdam, Amy C.; McKay, Christopher P.; Ming, Douglas W.; Morris, Richard V.; Navarro-González, Rafael; Niles, Paul B.; Pavlov, Alex; Squyres, Steven W.; Stern, Jennifer C.; Steele, Andrew; Wray, James J.

    2014-01-01

    The Sample Analysis at Mars (SAM) instrument on the Mars Science Laboratory (MSL) rover Curiosity detected evolved gases during thermal analysis of soil samples from the Rocknest aeolian deposit in Gale Crater. Major species detected (in order of decreasing molar abundance) were H2O, SO2, CO2, and O2, all at the µmol level, with HCl, H2S, NH3, NO, and HCN present at the tens to hundreds of nmol level. We compute weight % numbers for the major gases evolved by assuming a likely source and calculate abundances between 0.5 and 3 wt.%. The evolution of these gases implies the presence of both oxidized (perchlorates) and reduced (sulfides or H-bearing) species as well as minerals formed under alkaline (carbonates) and possibly acidic (sulfates) conditions. Possible source phases in the Rocknest material are hydrated amorphous material, minor clay minerals, and hydrated perchlorate salts (all potential H2O sources), carbonates (CO2), perchlorates (O2 and HCl), and potential N-bearing materials (e.g., Martian nitrates, terrestrial or Martian nitrogenated organics, ammonium salts) that evolve NH3, NO, and/or HCN. We conclude that Rocknest materials are a physical mixture in chemical disequilibrium, consistent with aeolian mixing, and that although weathering is not extensive, it may be ongoing even under current Martian surface conditions.

  4. EFFECT OF BEARING MACROGEOMETRY ON BEARING PERFORMANCE IN ELASTOHYDRODYNAMIC LUBRICATION

    Emin GÜLLÜ

    2000-01-01

    Full Text Available During manufacturing, ideal dimension and mutual positioning of machine elements proposed in project desing can be achieved only within certain range of tolerances. These tolerances, being classified in two groups, related to micro and macro geometry of machine elements, don't have to effect the functioning of these elements. So, as for all machine elements, investigation of the effects of macro and micro tolerances for journal bearings is important. In this study, we have investigated the effect of macro geometric irregularities of journal bearings on performance characteristics. In this regard, we have studied the change of bearing performance in respect to deviation from ideal circle for an elliptic shaft with small ovality rolling in circular journal bearing.

  5. Combined thin layer chromatography and gas chromatography with mass spectrometric analysis of lipid classes and fatty acids in malnourished polar bears (Ursus maritimus) which swam to Iceland.

    Eibler, Dorothee; Krüger, Sabine; Skírnisson, Karl; Vetter, Walter

    2017-03-01

    Between 2008 and 2011, four polar bears (Ursus maritimus) from the Greenland population swam and/or drifted on ice to Iceland where they arrived in very poor body condition. Body fat resources in these animals were only between 0% and 10% of the body weight (usually 25%). Here we studied the lipid composition in different tissues (adipose tissue if available, liver, kidney and muscle). Lipid classes were determined by thin layer chromatography (TLC) and on-column gas chromatography with mass spectrometry (GC/MS). The fatty acid pattern of total lipids and free fatty acids was analyzed by GC/MS in selected ion monitoring (SIM) mode. Additionally, cholesteryl esters and native fatty acid methyl esters, initially detected as zones in thin layer chromatograms, were enriched by solid phase extraction and quantified by GC/MS. The ratio of free fatty acids to native fatty acid methyl esters could be correlated with the remained body lipids in the polar bears and thus may also serve as a marker for other starving animals or even for humans. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Gas-hydrate-bearing sand reservoir systems in the offshore of India: Results of the India National Gas Hydrate Program Expedition 02

    Kumar, P.; Collett, Timothy S.; Vishwanath, K.; Shukla, K.M.; Nagalingam, J.; Lall, M.V.; Yamada, Y; Schultheiss, P.; Holland, M.

    2016-01-01

    The India National Gas Hydrate Program Expedition 02 (NGHP-02) was conducted from 3-March-2015 to 28-July-2015 off the eastern coast of India using the deepwater drilling vessel Chikyu. The primary goal of this expedition was to explore for highly saturated gas hydrate occurrences in sand reservoirs that would become targets for future production tests. The first two months of the expedition were dedicated to logging-whiledrilling (LWD) operations, with a total of 25 holes drilled and logged. The next three months were dedicated to coring operations at 10 of the most promising sites. With a total of five months of continuous field operations, the expedition was the most comprehensive dedicated gas hydrate investigation ever undertaken.

  7. Polar bears at risk

    Norris, S.; Rosentrater, L.; Eid, P.M. [WWF International Arctic Programme, Oslo (Norway)

    2002-05-01

    Polar bears, the world's largest terrestrial carnivore, spend much of their lives on the arctic sea ice. This is where they hunt and move between feeding, denning, and resting areas. The world population, estimated at 22,000 bears, is made up of 20 relatively distinct populations varying in size from a few hundred to a few thousand animals. About 60 per cent of all polar bears are found in Canada. In general, the status of this species is stable, although there are pronounced differences between populations. Reductions in the extent and thickness of sea ice has lead the IUCN Polar Bear Specialist Group to describe climate change as one of the major threats facing polar bears today. Though the long-term effects of climate change will vary in different areas of the Arctic, impacts on the condition and reproductive success of polar bears and their prey are likely to be negative. Longer ice-free periods resulting from earlier break-up of sea ice in the spring and later formation in the fall is already impacting polar bears in the southern portions of their range. In Canada's Hudson Bay, for example, bears hunt on the ice through the winter and into early summer, after which the ice melts completely, forcing bears ashore to fast on stored fat until freeze-up in the fall. The time bears have on the ice to hunt and build up their body condition is cut short when the ice melts early. Studies from Hudson Bay show that for every week earlier that ice break-up occurs, bears will come ashore 10 kg lighter and in poorer condition. It is likely that populations of polar bears dividing their time between land and sea will be severely reduced and local extinctions may occur as greenhouse gas emissions continue to rise and sea ice melts. Expected changes in regional weather patterns will also impact polar bears. Rain in the late winter can cause maternity dens to collapse before females and cubs have departed, thus exposing occupants to the elements and to predators. Such

  8. Application of the carbon dioxide-barium hydroxide hydrate gas-solid reaction for the treatment of dilute carbon dioxide-bearing gas streams

    Haag, G.L.

    1983-09-01

    The removal of trace components from gas streams via irreversible gas-solid reactions in an area of interest to the chemical engineering profession. This research effort addresses the use of fixed beds of Ba(OH) 2 hydrate flakes for the removal of an acid gas, CO 2 , from air that contains approx. 330 ppM/sub v/ CO 2 . Areas of investigation encompassed: (1) an extensive literature review of Ba(OH) 2 hydrate chemistry, (2) microscale studies on 0.150-g samples to develop a better understanding of the reaction, (3) process studies at the macroscale level with 10.2-cm-ID fixed-bed reactors, and (4) the development of a model for predicting fixed-bed performance. Experimental studies indicated fixed beds of commercial Ba(OH) 2 .8H 2 O flakes at ambient temperatures to be capable of high CO 2 -removal efficiencies (effluent concentrations 99%), and an acceptable pressure drop (1.8 kPa/m at a superficial gas velocity of 13 cm/s). Ba(OH) 2 .8H 2 O was determined to be more reactive toward CO 2 than either Ba(OH) 2 .3H 2 O or Ba(OH) 2 .1H 2 O. A key variable in the development of this fixed-bed process was relative humidity. Operation at conditions with effluent relative humidities >60% resulted in significant recrystallization and restructuring of the flake and subsequent pressure-drop problems

  9. Pyrolysis Gas as a Renewable Reducing Agent for the Recycling of Zinc- and Lead-Bearing Residues: A Status Report

    Pichler, C.; Antrekowitsch, J.

    2017-04-01

    The topic "Zero Waste" has been in existence for several years in the industry, and the metallurgical industry has also made efforts to reduce the amounts of residues occurring and have started several investigations to cut down on metallurgical by-products which have to be landfilled. Especially, the additional costs for CO2 emissions in different metallurgical steps have led to investigations into alternative carbon carriers. Charcoal has been identified to serve as an ideal substitute due its CO2-neutrality. For the applications of this renewable carbon carrier in metallurgical processes, charcoal production by means of a carbonization process needs to be optimized. As a by-product during the heating of agricultural wastes or wood by excluding air, pyrolysis gas occurs. Due to the existence of combustible compounds in this gas, an application as a reduction agent instead of fossil carbon carriers in metallurgy is possible. Based on the prevention of dumping metallurgical by-products, an investigation has been developed to treat zinc- and lead-containing materials. To realize this, a dedicated process concept has been designed and developed. As the main focuses, the usage of the pyrolysis gas from charcoal production for the Waelz kiln process and the recycling of zinc- and lead-containing Waelz slag, resulting from the processing of steel mill dust in a vertical retort, have to be mentioned. Within this research, the process concept was executed from laboratory-scale up to pilot-scale testing, described in this article.

  10. Load responsive hydrodynamic bearing

    Kalsi, Manmohan S.; Somogyi, Dezso; Dietle, Lannie L.

    2002-01-01

    A load responsive hydrodynamic bearing is provided in the form of a thrust bearing or journal bearing for supporting, guiding and lubricating a relatively rotatable member to minimize wear thereof responsive to relative rotation under severe load. In the space between spaced relatively rotatable members and in the presence of a liquid or grease lubricant, one or more continuous ring shaped integral generally circular bearing bodies each define at least one dynamic surface and a plurality of support regions. Each of the support regions defines a static surface which is oriented in generally opposed relation with the dynamic surface for contact with one of the relatively rotatable members. A plurality of flexing regions are defined by the generally circular body of the bearing and are integral with and located between adjacent support regions. Each of the flexing regions has a first beam-like element being connected by an integral flexible hinge with one of the support regions and a second beam-like element having an integral flexible hinge connection with an adjacent support region. A least one local weakening geometry of the flexing region is located intermediate the first and second beam-like elements. In response to application of load from one of the relatively rotatable elements to the bearing, the beam-like elements and the local weakening geometry become flexed, causing the dynamic surface to deform and establish a hydrodynamic geometry for wedging lubricant into the dynamic interface.

  11. Instrumented Pressure Testing Chamber (IPTC) Characterization of Methane Gas Hydrate-Bearing Pressure Cores Collected from the Methane Production Test Site in the Eastern Nankai Trough, Offshore Japan

    Waite, W. F.; Santamarina, J. C.; Dai, S.; Winters, W. J.; Yoneda, J.; Konno, Y.; Nagao, J.; Suzuki, K.; Fujii, T.; Mason, D. H.; Bergeron, E.

    2014-12-01

    Pressure cores obtained at the Daini-Atsumi Knoll in the eastern Nankai Trough, the site of the methane hydrate production test completed by the Methane Hydrate Resources in Japan (MH21) project in March 2013, were recovered from ~300 meters beneath the sea floor at close to in situ pressure. Cores were subsequently stored at ~20 MPa and ~5°C, which maintained hydrate in the cores within stability conditions. Pressure core physical properties were measured at 10 MPa and ~6°C, also within the methane hydrate stability field, using the IPTC and other Pressure Core Characterization Tools (PCCTs). Discrete IPTC measurements were carried out in strata ranging from silty sands to clayey silts within the turbidite sequences recovered in the cores. As expected, hydrate saturations were greatest in more permeable coarser-grained layers. Key results include: 1) Where hydrate saturation exceeded 40% in sandy sediments, the gas hydrate binds sediment grains within the matrix. The pressure core analyses yielded nearly in situ mechanical properties despite the absence of effective stress in the IPTC. 2) In adjacent fine-grained sediment (hydrate saturation < 15%), hydrate did not significantly bind the sediment. IPTC results in these locations were consistent with the zero effective-stress limit of comparable measurements made in PCCT devices that are designed to restore the specimen's in situ effective stress. In sand-rich intervals with high gas hydrate saturations, the measured compressional and shear wave velocities suggest that hydrate acts as a homogeneously-distributed, load-bearing member of the bulk sediment. The sands with high gas hydrate saturations were prone to fracturing (brittle failure) during insertion of the cone penetrometer and electrical conductivity probes. Authors would like to express their sincere appreciation to MH21 and the Ministry of Economy, Trade and Industry for permitting this work to be disclosed at the 2014 Fall AGU meeting.

  12. Grizzly bear

    Schwartz, C.C.; Miller, S.D.; Haroldson, M.A.; Feldhamer, G.; Thompson, B.; Chapman, J.

    2003-01-01

    The grizzly bear inspires fear, awe, and respect in humans to a degree unmatched by any other North American wild mammal. Like other bear species, it can inflict serious injury and death on humans and sometimes does. Unlike the polar bear (Ursus maritimus) of the sparsely inhabited northern arctic, however, grizzly bears still live in areas visited by crowds of people, where presence of the grizzly remains physically real and emotionally dominant. A hike in the wilderness that includes grizzly bears is different from a stroll in a forest from which grizzly bears have been purged; nighttime conversations around the campfire and dreams in the tent reflect the presence of the great bear. Contributing to the aura of the grizzly bear is the mixture of myth and reality about its ferocity. unpredictable disposition, large size, strength, huge canines, long claws, keen senses, swiftness, and playfulness. They share characteristics with humans such as generalist life history strategies. extended periods of maternal care, and omnivorous diets. These factors capture the human imagination in ways distinct from other North American mammals. Precontact Native American legends reflected the same fascination with the grizzly bear as modern stories and legends (Rockwell 1991).

  13. 49 CFR 215.107 - Defective plain bearing box: General.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective plain bearing box: General. 215.107... Suspension System § 215.107 Defective plain bearing box: General. A railroad may not place or continue in... the bearing; or (2) Have a detrimental effect on the lubrication of the journal and the bearings. ...

  14. Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

    Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Wang, P.; Liu, L. Q.

    2014-01-01

    An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

  15. Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

    Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Liu, L. Q. [Key Laboratory of Cryogenics, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing, 100190 (China); Wang, P. [Beijing Sciample Technology Co., Ltd., Beijing, 100190 (China)

    2014-01-29

    An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

  16. Examination and vibration characteristics of gas circulator (B1) of HENDEL

    Shimomura, Hiroaki; Izawa, Naoki; Ihzuka, Takayuki; Kawaji, Satoshi; Kunitama, Takehiko; Hayashi, Haruyoshi; Kobayashi, Toshiaki; Katoh, Michio

    1985-06-01

    An examination and vibration measurements were conducted on the gas bearing type high speed helium gas circulator after the failure on April 1984 and the repairing on August 1984. The examination made clear that the cause of the failure and scratching of gas bearing pads and journal shaft was found. The vibrational spectra showed a clear difference between failed and repaired conditions, and a frequency analysis technique by means of fast Fourier transform and a small-scale computer is expected as a useful method of diagnosis for circulators. A conceptual scheme of gas circulator diagnostic system based on above principle is shown, and a basic process of diagnostic software is described. (author)

  17. Plotting and Determination of Nominal Stresses in the Сrankshaft Components of V Configuration Engine with Offset Rod Bearing Journals

    M. Yu. Mikhailov

    2017-01-01

    Full Text Available Currently, a great number of large vehicle engines, especially diesel ones, have a V-shaped configuration layout. For six-cylinder and eight-cylinder V-engines, to simplify a processing technology of the block-crankcases, in the section manufacturers often use the 90° angle, which is the most prevalent angle for the V8 engine. However, in this case, an even firing cycle in the cylinders is not provided for the V6 layout. This leads to significant vibrations, especially at idle and requires for a more massive flywheel.Designers face the challenge to provide the even firing cycle in the cylinders. To solve this problem are often used the crankshaft designs, which have the offset rod journals. However, it leads to the manufacturing complexity of the shaft, and also to the need to use the special methods of calculation.There are no direct calculation methods for the crankshafts of this design. The paper proposes a technique to define the nominal stresses in the crankshaft of this design. To consider the shaft is used a split-type design. The paper presents a schematic diagram of the crankshaft loading, and on its basis describes equations of the moments for each section. A special attention is drawn to the new constructive element, i.e. an intermediate cheek. For clarity, the diagrams of moments in two mutually perpendicular planes are built. It is worth noting that the paper also proposes a technique from transition from the global to the local coordinate system when considering the moments in the crankshaft elements.Further, there are the appropriate expressions to determine the nominal stresses. This is one of the main desired values in calculating the crankshaft endurance. The developed technique in the particular case allows the calculation of crankshaft engine models that can be subsumed under the advantages.In the future the proposed technique is expected to be a basis for creating a software complex. The complex objective is expected to be

  18. Uganda Journal of Agricultural Sciences: Submissions

    The Uganda Journal of Agricultural Sciences (UJAS) (ISSN: 1026-0919) is a peer reviewed journal ... It should bear a background statement to originate the idea or research problem; ... Truly new procedures should be described in detail.

  19. Monitoring and mitigating measures to reduce potential impacts of oil and gas exploration and development on bears in the Inuvik region

    Branigan, M. [Government of the Northwest Territories, Inuvik, NT (Canada). Dept. of Environment and Natural Resources

    2007-07-01

    The Inuvik Region consists of the Northwest Territories portion of the Inuvialuit Settlement Region and the Gwich'in Settlement Area. The range of grizzly bears, polar bears and black bears extends to different parts of the region. The potential impact of development depends on the season of the development and the species of bear found in the footprint. As such, monitoring and mitigation measures should take this into consideration. This presentation focused on the potential impacts and current practices to monitor and mitigate the impacts in the region. Mitigation measures currently used include: communication with stakeholders; waste management guidelines; use of wildlife monitors to identify key habitat and den sites and to deter bears; minimum flight altitudes; and safety training. Suggestions for additional mitigation measures were also presented. figs.

  20. Shaft Center Orbit in Dynamically Loaded Bearings

    Klit, Peder

    2005-01-01

    The aim of this work is to demonstrate how to utilize the bearings damping coe±cients to estimate the orbit for a dynamically loaded journal bearing. The classical method for this analysis was developed by Booker in 1965 [1]and described further in 1972 [2]. Several authors have re¯ned this metho...

  1. Bear at the back door | Prinsloo | Scientia Militaria: South African ...

    Scientia Militaria: South African Journal of Military Studies. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 9, No 3 (1979) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. Bear at the back door. C Prinsloo ...

  2. Hydrodynamic bearings

    Bonneau, Dominique; Souchet, Dominique

    2014-01-01

    This Series provides the necessary elements to the development and validation of numerical prediction models for hydrodynamic bearings. This book describes the rheological models and the equations of lubrication. It also presents the numerical approaches used to solve the above equations by finite differences, finite volumes and finite elements methods.

  3. Identification of Bearing Failure Using Signal Vibrations

    Yani, Irsyadi; Resti, Yulia; Burlian, Firmansyah

    2018-04-01

    Vibration analysis can be used to identify damage to mechanical systems such as journal bearings. Identification of failure can be done by observing the resulting vibration spectrum by measuring the vibration signal occurring in a mechanical system Bearing is one of the engine elements commonly used in mechanical systems. The main purpose of this research is to monitor the bearing condition and to identify bearing failure on a mechanical system by observing the resulting vibration. Data collection techniques based on recordings of sound caused by the vibration of the mechanical system were used in this study, then created a database system based bearing failure due to vibration signal recording sounds on a mechanical system The next step is to group the bearing damage by type based on the databases obtained. The results show the percentage of success in identifying bearing damage is 98 %.

  4. Bears and pipeline construction in Alaska

    Follmann, E.H.; Hechtel, J.L. (Univ. of Alaska Fairbanks, AK (USA))

    1990-06-01

    Serious problems were encountered with bears during construction of the 1274-km trans-Alaska oil pipeline between Prudhoe Bay and Valdez. This multi-billion-dollar project traversed both black bear (Ursus americanus Pallas) and grizzly bear (U. arctos L.) habitat throughtout its entire length. Plans for dealing with anticipated problems with bears were often inadequate. Most (71%) problems occurred north of the Yukon River in a previously roadless wilderness where inadequate refuse disposal and widespread animal feeding created dangerous situations. Of the 192 officially reported bear problems associated with the Trans-Alaska Pipeline System (TAPS) (1971-1979), about 65% involved the presence of bears in camps or dumps, 13% the feeding of bears on garbage or handouts, 10% property damage or economic loss, 7% bears under and in buildings, and only 5% charges by bears. Remarkably, no bear-related injuries were reported, suggesting that bears became accustomed to people and did not regard them as a threat. Following construction of the TAPS there have been proposals for pipelines to transport natural gas from Prudhoe Bay to southern and Pacific-rim markets. Based on past experience, some animal control measures were developed during the planning phase for the authorized gas pipeline route in Alaska. Fences installed around 100-person survey camps were found to be effective in deterring bears in two traditionally troublesome areas. 16 refs., 7 figs., 1 tab.

  5. Bearing structures

    Lee, A.S.; Preece, G.E.

    1988-01-01

    A hydrostatic bearing for the lower end of the vertical shaft of a sodium pump comprises a support shell encircling the shaft and a bush located between the shell and shaft. Liquid sodium is fed from the pump outlet to the bush/shaft and bush/shell interfaces to provide hydrostatic support. The bush outer surface and the shell inner surface are of complementary part-spherical shape and the bush floats relative to the shaft so that the bush can align itself with the shaft axis. Monitoring of the relative rotational speed of the bush with respect to the shaft (such rotation being induced by the viscous drag forces present) is also performed for the purposes of detecting abnormal operation of the bearing or partial seizure, at least one magnet is rotatable with the bush, and a magnetic sensor provides an output having a frequency related to the speed of the bush. (author)

  6. Enhancing stability of industrial turbines using adjustable partial arc bearings

    Chasalevris, Athanasios; Dohnal, Fadi

    2016-09-01

    The paper presents the principal of operation, the simulation and the characteristics of two partial-arc journal bearings of variable geometry and adjustable/controllable stiffness and damping properties. The proposed journals are supposed to consist of a scheme that enables the periodical variation of bearing properties. Recent achievements of suppressing rotor vibrations using plain circular journal bearings of variable geometry motivate the further extension of the principle to bearings of applicable geometry for industrial turbines. The paper describes the application of a partial-arc journal bearing to enhance stability of high speed industrial turbines. The proposed partial-arc bearings with adjustable/controllable properties enhance stability and they introduce stable margins in speeds much higher than the 1st critical.

  7. Estimation of seismic attenuation of gas hydrate bearing sediments from multi-channel seismic data: A case study from Krishna-Godavari offshore basin

    Dewangan, P.; Mandal, R.; Jaiswal, P.; Ramprasad, T.; Sriram, G.

    thickness of water column. The estimated effective Q-values, along the inline and crossline seismic profiles, depend on several factors such as gas hydrate, free gas and the complex fault system. The combined interpretation of the quality factor...

  8. Gas

    1996-01-01

    The French government has decided to modify the conditions of extension of local natural gas authorities to neighbouring districts. The European Union is studying the conditions of internal gas market with the objective of more open markets although considering public service requirements

  9. Design of Temperature Measuring Instrument of The Primary Cooling System Bearing Motor At The RSG-GAS Based on Micro controller ATMEGA 8535

    Ranji Gusman; Cahyana; Heri Suherkiman; Sukino

    2012-01-01

    Controlling on the bearing of an electric motor is the thing that important to do, to know the performance of an electric motor is staying awake. One of the parameters that can be controlled is temperature of bearing electric motor. The bearing of an electric motors has three areas of work, namely the normal working temperature area(<45 °C), working area (45-50 °C) and critical shutdown area (<50 °C). On the design of this tool-making, we are going to control the electric motor on that condition. The micro controller ATMEGA 8535 is used as a controller. Micro controller serve control the input in the form of temperature bearing motor then cultivate it and will be displayed to output devices such as the LCD viewer, lights indicators and buzzer. On this design has the design of casing, power supply circuit, micro controller port, buzzer driver circuit, indicator light and relay circuits, as well as the LCD viewer circuit and flow chart. On the next activity, the design will be submitted to the manufacturing stage. (author)

  10. Rethinking Journalism Again

    . But does rehashing such familiar rationales bring journalism studies forward? Does it contribute to ongoing discussions surrounding journalism’s viability going forth? For all their seeming self-evidence, this book considers what bearing these old platitudes have in the new digital era. It asks whether......It’s easy to make a rhetorical case for the value of journalism. Because, it is a necessary precondition for democracy; it speaks to the people and for the people; it informs citizens and enables them to make rational decisions; it functions as their watchdog on government and other powers that be...... such hopeful talk really reflects the concrete roles journalism now performs for people in their everyday lives. In essence, it poses questions that strike at the core of the idea of journalism itself. Is there a singular journalism that has one well-defined role in society? Is its public mandate as strong...

  11. Scaling laws for radial foil bearings

    Honavara Prasad, Srikanth

    The effects of fluid pressurization, structural deformation of the compliant members and heat generation in foil bearings make the design and analysis of foil bearings very complicated. The complex fluid-structural-thermal interactions in foil bearings also make modeling efforts challenging because these phenomena are governed by highly non-linear partial differential equations. Consequently, comparison of various bearing designs require detailed calculation of the flow fields (velocities, pressures), bump deflections (structural compliance) and heat transfer phenomena (viscous dissipation in the fluid, frictional heating, temperature profile etc.,) resulting in extensive computational effort (time/hardware). To obviate rigorous computations and aid in feasibility assessments of foil bearings of various sizes, NASA developed the "rule of thumb" design guidelines for estimation of journal bearing load capacity. The guidelines are based on extensive experimental data. The goal of the current work is the development of scaling laws for radial foil bearings to establish an analytical "rule of thumb" for bearing clearance and bump stiffness. The use of scale invariant Reynolds equation and experimentally observed NASA "rule of thumb" yield scale factors which can be deduced from first principles. Power-law relationships between: a. Bearing clearance and bearing radius, and b. bump stiffness and bearing radius, are obtained. The clearance and bump stiffness values obtained from scaling laws are used as inputs for Orbit simulation to study various cases. As the clearance of the bearing reaches the dimensions of the material surface roughness, asperity contact breaks the fluid film which results in wear. Similarly, as the rotor diameter increases (requiring larger bearing diameters), the load capacity of the fluid film should increase to prevent dry rubbing. This imposes limits on the size of the rotor diameter and consequently bearing diameter. Therefore, this thesis aims

  12. Thermohydrodynamic analysis of cryogenic liquid turbulent flow fluid film bearings

    Andres, Luis San

    1993-01-01

    A thermohydrodynamic analysis is presented and a computer code developed for prediction of the static and dynamic force response of hydrostatic journal bearings (HJB's), annular seals or damper bearing seals, and fixed arc pad bearings for cryogenic liquid applications. The study includes the most important flow characteristics found in cryogenic fluid film bearings such as flow turbulence, fluid inertia, liquid compressibility and thermal effects. The analysis and computational model devised allow the determination of the flow field in cryogenic fluid film bearings along with the dynamic force coefficients for rotor-bearing stability analysis.

  13. Eastern slopes grizzly bear project

    NONE

    2001-01-01

    The cumulative effects of human activities on the grizzly bears in the central Canadian Rockies are not well known. As a result, a project was initiated in 1994 to address the urgent requirement for accurate scientific information on the habitat and populations of grizzly bears in the area of the Banff National Park and Kananaskis Country. This area is probably the most heavily used and developed area where the grizzly still survives. The information gathered throughout the course of this study will be used to better protect and manage the bears and other sensitive carnivores in the region. Using telemetry, researchers are monitoring 25 grizzly bears which were radio-collared in a 22,000 square-kilometer area in the upper Bow Valley drainage of the eastern Alberta slopes. The researchers involved in the project are working with representatives from Husky Oil and Talisman Energy on the sound development of the Moose Mountain oil and gas field without adversely affecting the grizzly bear population. Information collected over seven years indicated that the grizzly bears have few and infrequent offspring. Using the information gathered so far, the location of the Moose Mountain to Jumping Pound pipeline was carefully selected, since the bears recover very slowly from high mortality, and also considering that the food and cover had already been compromised by the high number of roads, trails and other human activities in the area. The status of the population and habitat of the grizzly bear will be assessed upon the conclusion of the field research phase in 2001. Models will be updated using the data obtained during eight years and will assist in the understanding of complex variables that affect grizzly bears.

  14. Journal of Pharmacy & Bioresources: Journal Sponsorship

    Journal of Pharmacy & Bioresources: Journal Sponsorship. Journal Home > About the Journal > Journal of Pharmacy & Bioresources: Journal Sponsorship. Log in or Register to get access to full text downloads.

  15. Hydrodynamic bearing lubricated with magnetic fluids

    Urreta, H; Leicht, Z; Sanchez, A; Agirre, A; Kuzhir, P; Magnac, G

    2009-01-01

    This paper summarizes the work carried out in the development of hydrodynamic lubricated journal bearings with magnetic fluids. Two different fluids have been analyzed, one ferrofluid from FERROTEC APG s10n and one magnetorheological fluid from LORD Corp., MRF122-2ED. Theoretical analysis has been carried out with numerical solutions of Reynolds equation, based on apparent viscosity modulation for ferrofluid and Bingham model for MR fluid. To validate this model, one test bench has been designed, manufactured and set up, where preliminary results shown in this paper demonstrate that magnetic fluids can be used to develop active journal bearings.

  16. Constraining gas hydrate occurrence in the northern Gulf of Mexico continental slope : fine scale analysis of grain-size in hydrate-bearing sediments

    Hangsterfer, A.; Driscoll, N.; Kastner, M. [Scripps Inst. of Oceanography, La Jolla, CA (United States). Geosciences Research Division

    2008-07-01

    Methane hydrates can form within the gas hydrate stability zone (GHSZ) in sea beds. The Gulf of Mexico (GOM) contains an underlying petroleum system and deeply buried, yet dynamic salt deposits. Salt tectonics and fluid expulsion upward through the sediment column result in the formation of fractures, through which high salinity brines migrate into the GHSZ, destabilizing gas hydrates. Thermogenic and biogenic hydrocarbons also migrate to the seafloor along the GOMs northern slope, originating from the thermal and biogenic degradation of organic matter. Gas hydrate occurrence can be controlled by either primary permeability, forming in coarse-grained sediment layers, or by secondary permeability, forming in areas where hydrofracture and faulting generate conduits through which hydrocarbon-saturated fluids flow. This paper presented a study that attempted to determine the relationship between grain-size, permeability, and gas hydrate distribution. Grain-size analyses were performed on cores taken from Keathley Canyon and Atwater Valley in the GOM, on sections of cores that both contained and lacked gas hydrate. Using thermal anomalies as proxies for the occurrence of methane hydrate within the cores, samples of sediment were taken and the grain-size distributions were measured to see if there was a correlation between gas hydrate distribution and grain-size. The paper described the methods, including determination of hydrate occurrence and core analysis. It was concluded that gas hydrate occurrence in Keathley Canyon and Atwater Valley was constrained by secondary permeability and was structurally controlled by hydrofractures and faulting that acted as conduits through which methane-rich fluids flowed. 11 refs., 2 tabs., 5 figs.

  17. Camshaft bearing arrangement for overhead cam engine

    Yoshikawa, M.

    1985-01-01

    In an assembly for an internal combustion engine comprising a cylinder block, a cylinder head detachably affixed to the cylinder block by a plurality of threaded fastening means, a plurality of poppet valves supported for reciprocation in the cylinder head and a camshaft for operating the poppet valves, the improvement is described comprising a cam carrier detachably affixed to the cylinder head and overlying the threaded fastening means, and a bearing cap affixed to the cam carrier. The cam carrier and the bearing cap have bearing surfaces for journaling the camshaft.

  18. Journals Abroad

    Ando, Shoichi

    1975-01-01

    This article summarizes four journal articles on language teaching appearing in the American pedagogical language journals, "The Modern Language Journal,""English Language Teaching Journal," and "TESOL Quarterly." The purpose is to give an indication of what kinds of articles can be found in journals outside Japan.…

  19. Journal Management

    The Journal Manager sees to all aspects of Journal Management, in consultation with the Editors, including setting up and configuring the journal system, enrolling users in the various roles needed to run the journal, setting up the various Sections of the journal, and many other managerial tasks.

  20. Journal Home

    for Researchers · for Journals · for Authors · for Policy Makers · about Open Access · Journal Quality. 521 African Journals. Browse By Category · Browse Alphabetically · Browse By Country · List All Titles · Free To Read Titles This Journal is Open Access. Featuring journals from 32 Countries: Algeria (5); Benin (2); Botswana ...

  1. Superconducting Meissner effect bearings for cryogenic turbomachines, phase 2

    Valenzuela, Javier A.; Martin, Jerry L.

    1994-02-01

    This is the final report of a Phase 2 SBIR project to develop Meissner effect bearings for miniature cryogenic turbomachines. The bearing system was designed for use in miniature cryogenic turboexpanders in reverse-Brayton-cycle cryocoolers. The cryocoolers are designed to cool sensors on satellites. Existing gas bearings for this application run in a relatively warm state. The heat loss from the bearings into the shaft and into the cold process gas imposes a penalty on the cycle efficiency. By using cold Meissner effect bearings, this heat loss could be minimized, and the input power per unit of cooling for these cryocoolers could be reduced. Two bearing concepts were explored in this project. The first used an all-magnetic passive radial suspension to position the shaft over a range of temperatures from room temperature to 77 K. This bearing concept was proven to be feasible, but impractical for the miniature high-speed turbine application since it lacked the required shaft positioning accuracy. A second bearing concept was then developed. In this concept, the Meissner effect bearings are combined with self-acting gas bearings. The Meissner effect bearing provides the additional stiffness and damping required to stabilize the shaft at low temperature, while the gas bearing provides the necessary accuracy to allow very small turbine tip clearances (5mm) and high speeds (greater than 500,000 rpm).

  2. Method for greenhouse gas emission assessments according to the article 75 of the 2010-788 law of July 12, 2010 bearing national commitment for the environment (ENE)

    2011-01-01

    This document presents mandatory methodological principles, optional prescriptions and optional recommendations for the assessment of greenhouse gas emissions. After having recalled some basic definitions, and regulatory arrangements and performance principles for greenhouse gas emission assessment, this document proposes a diagram indicating the main steps of such an assessment. It defines the organisational frame (for companies or communities), presents the concept of operational perimeter. It reviews the general principles of the assessment: global approach and priorities, calculation with respect to measurement, emission factors, gas global warming potential, reporting and reference year, uncertainty management, case of electricity, case of biomass CO 2 , cogeneration and electricity production from renewable energy, compensation. It presents the reporting format. Some aspects are more precisely presented or described in appendix

  3. 'Dodo' and 'Baby Bear' Trenches

    2008-01-01

    NASA's Phoenix Mars Lander's Surface Stereo Imager took this image on Sol 11 (June 5, 2008), the eleventh day after landing. It shows the trenches dug by Phoenix's Robotic Arm. The trench on the left is informally called 'Dodo' and was dug as a test. The trench on the right is informally called 'Baby Bear.' The sample dug from Baby Bear will be delivered to the Phoenix's Thermal and Evolved-Gas Analyzer, or TEGA. The Baby Bear trench is 9 centimeters (3.1 inches) wide and 4 centimeters (1.6 inches) deep. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

  4. Insights into contaminant transport from unconventional oil and gas developments from analog system analysis of methane-bearing thermal springs in the northern Canadian Rocky Mountains

    Ferguson, Grant; Grasby, Stephen E.

    2018-03-01

    Natural gas is currently being produced from shales of the Montney and Liard basins in western Canada. Production requires hydraulic fracturing due to the low permeability of the shales in the basins. Stratigraphically equivalent shales are present in the northern Canadian Rocky Mountains. Thermal springs with notable hydrocarbon concentrations occur where large-scale faults intersect the same shale units that are the focus of gas development, indicating that under certain circumstances, connection of deep fractured shales to the land surface is possible. To constrain these conditions, simulations were conducted for the spring with the highest hydrocarbon flux (Toad River Spring), results of which indicate that in order to supply sufficient water to a fault to support measurable advection, the effective permeability of the shales in these structurally deformed areas must be one to four orders of magnitude higher than in areas of active gas production to the east. The spatial scale of enhanced permeability is much greater than that which is achieved by hydraulic fracturing and the mechanism of maintaining high pressures at depth is more persistent in time. Examination of groundwater velocities suggests that upward migration of solutes from hydraulic fracturing may take decades to centuries. Results also indicate that any temperature anomaly will be associated with transport along a fault at such velocities. No such temperature anomaly has been documented in regions with unconventional oil and gas development to date. Such an anomaly would be diagnostic of a deep solute source.

  5. Creative Journalism: English, Journalism.

    Adams, Marlene E.

    A course in the basic principles of journalism is presented. The principles are studied as applied to writing columns, reviews, feature stories, human interest articles, fashion reporting, comics, personality interviews, and other types of entertaining writing for the newspaper. Course objectives include: (1) The student will identify feature…

  6. Journalism Forum.

    Journalism Educator, 1982

    1982-01-01

    Journalism teachers share ideas about copywriting assignments, research in public relations, student involvement in a television production, and the use of journalism classes to monitor language skills. (HOD)

  7. The journal of irreproducible results II

    Scherr, George H

    1997-01-01

    Compilation of offbeat science papers from the Journal of Irreproducible Results, including: Emotion in the Rat Face; Foamy Beer; Cooking with Potential Energy; The Large-Cake Cutting Problem; Siamese Twinning in Gummy Bears; much more.

  8. Estimates of Water Ingestion for Women in Pregnant, Lactating and Non-Pregnant and Non-Lactating Child Bearing Age Groups Based on USDA's 1994-96, 1998 Continuing Survey of Food Intake by Individuals (Journal Article)

    Women in the child bearing age of 15 to 44 years and, in particular, pregnant and lactating women in this age cohort are considered a sensitive subpopulation when assessing risk from ingestion of contaminated water because ingested contaminants may pose a risk not only to the mot...

  9. Towards accurate prediction of unbalance response, oil whirl and oil whip of flexible rotors supported by hydrodynamic bearings

    Eling, R.P.T.; te Wierik, M.; van Ostayen, R.A.J.; Rixen, D.J.

    2016-01-01

    Journal bearings are used to support rotors in a wide range of applications. In order to ensure reliable operation, accurate analyses of these rotor-bearing systems are crucial. Coupled analysis of the rotor and the journal bearing is essential in the case that the rotor is flexible. The accuracy of

  10. Shaft centre orbit for dynamically loaded radial bearings

    Klit, Peder; Vølund, Anders

    2002-01-01

    The aim of this work is to demonstrate how to utilize the bearings damping coefficients to estimate the orbit for a dynamically loaded journal bearing. The classical method for this analysis was developed by Booker in 1965 Booker1 and described further in 1972 Booker2. Several authors have refine...

  11. Optimising inflow performance of a long multi-lateral offshore well in low permeability, gas-bearing sandstone: K14-FB 102 case study

    Hands, N. [Shell Canada Ltd., Calgary, AB (Canada); Francis, P. [Shell International Exploration and Production (Netherlands); Whittle, A.; Rajasingam, D. [NAM B. V. (Netherlands)

    1998-12-31

    Successful completion of the sub-horizontal dual-lateral well, K14-FB 102, to optimize production capacity and reservoir drainage in an offshore gas play in the Dutch sector of the North Sea is described. The two 5-7/8 inch horizontal production intervals were drilled and completed using a rheologically engineered, minimal solids, non-damaging sodium formate brine- based fluid designed as a drill-in fluid for reservoir intervals. The completion was made possible by the selection of the appropriate reservoir drill-in and completion fluid, appropriate level of contingency planning and a fully integrated team approach and custom-made well solution. Inflow performance has matched the performance of cemented and high-performance wells at a much lower cost. It was found that openhole reservoir completion techniques offer relatively inexpensive `fit-for-purpose` well solutions for low permeability sandstone in this region of the North Sea.3 refs., 6 tabs., 7 figs.

  12. Bearings for the HFIR control plates

    Abbatiello, A.A.

    1975-08-01

    Recent accelerated wear of HFIR bearings seems to be a more advanced stage of the situation encountered in 1967. The latest observations are in agreement with the hypothesis that high-frequency impact loads at a 30 0 angle on these bearings are the apparent basic cause of their short life. In view of the limited possibilities for change at this stage of HFIR operation, the region of best payoff seems to be an increase in the load-carrying area at some acceptable sacrifice of low rolling friction. On this basis three types of bearings are proposed for test--two of these are journal types and one is a slider type. The next planned shutdown for major parts replacement provides an opportunity to test these modified bearing types in the HFIR under full mechanical operating conditions but without nuclear operation. The program is recommended for consideration and adoption. (U.S.)

  13. Operation and design selection of high temperature superconducting magnetic bearings

    Werfel, F N; Floegel-Delor, U; Riedel, T; Rothfeld, R; Wippich, D; Goebel, B

    2004-01-01

    Axial and radial high temperature superconducting (HTS) magnetic bearings are evaluated by their parameters. Journal bearings possess advantages over thrust bearings. High magnetic gradients in a multi-pole permanent magnet (PM) configuration, the surrounding melt textured YBCO stator and adequate designs are the key features for increasing the overall bearing stiffness. The gap distance between rotor and stator determines the specific forces and has a strong impact on the PM rotor design. We report on the designing, building and measuring of a 200 mm prototype 100 kg HTS bearing with an encapsulated and thermally insulated melt textured YBCO ring stator. The encapsulation requires a magnetically large-gap (4-5 mm) operation but reduces the cryogenic effort substantially. The bearing requires 3 l of LN 2 for cooling down, and about 0.2 l LN 2 h -1 under operation. This is a dramatic improvement of the efficiency and in the practical usage of HTS magnetic bearings

  14. The estimation of CO2 storage potential of gas-bearing shale complex at the early stage of reservoir characterization: the case of Baltic Basin (Poland).

    Wójcicki, Adam; Jarosiński, Marek

    2017-04-01

    For the stage of shale gas production, like in the USA, prediction of the CO2 storage potential in shale reservoir can be performed by dynamic modeling. We have made an attempt to estimate this potential at an early stage of shale gas exploration in the Lower Paleozoic Baltic Basin, based on data from 3,800 m deep vertical well (without hydraulic fracking stimulation), supplemented with additional information from neighboring boreholes. Such an attempt makes a sense as a first guess forecast for company that explores a new basin. In our approach, the storage capacity is build by: (1) sorption potential of organic matter, (2) open pore space and (3) potential fracture space. the sequence. our estimation is done for 120 m long shale sequence including three shale intervals enriched with organic mater. Such an interval is possible to be fracked from a single horizontal borehole as known from hydraulic fracture treatment in the other boreholes in this region. The potential for adsorbed CO2 is determined from Langmuir isotherm parameters taken from laboratory measurements in case of both CH4 and CO2 adsorption, as well as shale density and volume. CO2 has approximately three times higher sorption capacity than methane to the organic matter contained in the Baltic Basin shales. Finally, due to low permeability of shale we adopt the common assumption for the USA shale basins that the CO2 will be able to reach effectively only 10% of theoretical total sorption volume. The pore space capacity was estimated by utilizing results of laboratory measurements of dynamic capacity for pores bigger than 10 nm. It is assumed for smaller pores adsorption prevails over free gas. Similarly to solution for sorption, we have assumed that only 10 % of the tight pore space will be reached by CO2. For fracture space we have considered separately natural (tectonic-origin) and technological (potentially produced by hydraulic fracturing treatment) fractures. From fracture density profile and

  15. Intrinsic gas-phase reactivity toward methanol of trinuclear tungsten W(3)S(4) complexes bearing W-X (X = Br, OH) groups.

    Vicent, Cristian; Feliz, Marta; Llusar, Rosa

    2008-12-11

    Electrospray ionization (ESI) tandem mass spectrometry is used to investigate the gas-phase dissociation of trinuclear sulfide W(3)S(4) complexes containing three diphosphane ligands and three terminal bromine atoms, namely, [W(3)S(4)(dmpe)(3)(Br)(3)](+) (1(+)) or hydroxo groups, [W(3)S(4)(dmpe)(3)(OH)(3)](+) (2(+)) (dmpe = 1,2-bis(dimethylphosphanyl)ethane). Sequential evaporation of two diphosphane ligands is the sole fragmentation channel for the 1(+) cation that yields product ions with one or two unsaturated W-Br functional groups, respectively. Conversely, evaporation of one diphosphane ligand followed by two water molecules is observed for cation 2(+). Complementary deuterium-labeling experiments in conjunction with computational studies provide deep insight into the thermodynamically favored product ion structures found along the fragmentation pathways. From these results, the formation of a series of cluster cations with WBr, WOH, and WO functional groups either on saturated or unsaturated metal sites is proposed. The effect of the properties of these cluster cations, among them chemical composition and coordinative saturation, on their reactivity toward methanol is discussed.

  16. Milestone Report - M3FT-15OR03120213 - A Literature Survey to Identify Potentially Problematic Volatile Iodine-Bearing Species Present in Off-Gas Streams

    Riley, Brian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Soelberg, Nick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Strachan, Denis M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-06-30

    Four radionuclides have been identified as being sufficiently volatile in the reprocessing of nuclear fuel that their gaseous release needs to be controlled to meet U.S. regulatory requirements (Jubin et al. 2011, 2012). These radionuclides are 3H, 14C, 85Kr, and 129I. Of these, 129I has the longest half-life and potentially highest biological impact. Accordingly, control of the release of 129I is most critical with respect to U.S. regulations for the release of radioactive material in stack emissions. Current U.S. Environmental Protection Agency regulation governing nuclear facilities (40 CFR 190) states that the total quantity of radioactive materials entering the general environment from the entire uranium fuel cycle, per gigawatt-year of electrical energy produced by the fuel cycle, must contain less than 5 mCi of 129I. The study of inorganic iodide in off-gas systems has been almost exclusively limited to I2, and the focus of organic iodide studies has been CH3I.

  17. Teddy Bear Stories

    van Leeuwen, Theo; Caldas-Coulthardt, Carmen

    2014-01-01

    This paper presents a semiotic analysis of a key cultural artefact, the teddy bear. After introducing the iconography of the teddy bear, it analyses different kinds of stories to show how teddy bears are endowed with meaning in everyday life: stories from children's books, reminiscenses by adults...... bears have traditionally centred on interpersonal relations within the nuclear family, but have recently been institutionalized and commercialized....

  18. International Journal of Humanistic Studies: Journal Sponsorship

    International Journal of Humanistic Studies: Journal Sponsorship. Journal Home > About the Journal > International Journal of Humanistic Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

  19. Nigerian Journal of Gastroenterology and Hepatology: Journal ...

    Nigerian Journal of Gastroenterology and Hepatology: Journal Sponsorship. Journal Home > About the Journal > Nigerian Journal of Gastroenterology and Hepatology: Journal Sponsorship. Log in or Register to get access to full text downloads.

  20. East African Journal of Statistics: Journal Sponsorship

    East African Journal of Statistics: Journal Sponsorship. Journal Home > About the Journal > East African Journal of Statistics: Journal Sponsorship. Log in or Register to get access to full text downloads.

  1. Nigerian Journal of General Practice: Journal Sponsorship

    Nigerian Journal of General Practice: Journal Sponsorship. Journal Home > About the Journal > Nigerian Journal of General Practice: Journal Sponsorship. Log in or Register to get access to full text downloads.

  2. African Journal of Infectious Diseases: Journal Sponsorship

    African Journal of Infectious Diseases: Journal Sponsorship. Journal Home > About the Journal > African Journal of Infectious Diseases: Journal Sponsorship. Log in or Register to get access to full text downloads.

  3. West African Journal of Radiology: Journal Sponsorship

    West African Journal of Radiology: Journal Sponsorship. Journal Home > About the Journal > West African Journal of Radiology: Journal Sponsorship. Log in or Register to get access to full text downloads.

  4. African Journal of Neurological Sciences: Journal Sponsorship

    African Journal of Neurological Sciences: Journal Sponsorship. Journal Home > About the Journal > African Journal of Neurological Sciences: Journal Sponsorship. Log in or Register to get access to full text downloads.

  5. African Journal of AIDS Research: Journal Sponsorship

    African Journal of AIDS Research: Journal Sponsorship. Journal Home > About the Journal > African Journal of AIDS Research: Journal Sponsorship. Log in or Register to get access to full text downloads.

  6. African Journal of Political Science: Journal Sponsorship

    African Journal of Political Science: Journal Sponsorship. Journal Home > About the Journal > African Journal of Political Science: Journal Sponsorship. Log in or Register to get access to full text downloads.

  7. African Journal of Management Research: Journal Sponsorship

    African Journal of Management Research: Journal Sponsorship. Journal Home > About the Journal > African Journal of Management Research: Journal Sponsorship. Log in or Register to get access to full text downloads.

  8. Journal of Civil Engineering, JKUAT: Journal Sponsorship

    Journal of Civil Engineering, JKUAT: Journal Sponsorship. Journal Home > About the Journal > Journal of Civil Engineering, JKUAT: Journal Sponsorship. Log in or Register to get access to full text downloads.

  9. New Egyptian Journal of Microbiology: Journal Sponsorship

    New Egyptian Journal of Microbiology: Journal Sponsorship. Journal Home > About the Journal > New Egyptian Journal of Microbiology: Journal Sponsorship. Log in or Register to get access to full text downloads.

  10. Mgbakoigba: Journal of African Studies: Journal Sponsorship

    Mgbakoigba: Journal of African Studies: Journal Sponsorship. Journal Home > About the Journal > Mgbakoigba: Journal of African Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

  11. Stability Zone of Natural Gas Hydrates in a Permafrost-Bearing Region of the Beaufort-Mackenzie Basin: Study of a Feasible Energy Source (Geological Survey of Canada Contribution No.1999275)

    Majorowicz, J. A.; Hannigan, P. K.

    2000-01-01

    Analysis of geological and geophysical data from 150 wells in the Beaufort-Mackenzie region(study area between 68 deg. 30'-70 deg. 00'N and 131 deg. -39 deg. W) led to reinterpretation of the depth of methane hydrate stability and construction of the first contour maps displaying thickness of hydrate stability zones as well as hydrate stability zone thicknesses below permafrost. Calculations were based on construction of temperature-depth profiles incorporating regional heat-flow values, temperature at the base of ice-bearing permafrost, and models relating thermal conductivity with depth. Data analysis indicates the presence and extent of the methane hydrate stability zone is related mainly to the history of permafrost development and less so by the relatively small regional variations of temperature gradients. Analysis of well logs and other indicators in conjunction with knowledge of the hydrate stability zone allows reevaluation of the location of possible gas hydrate occurrences. Log analysis indicates that in the onshore and shallow sea area of the Beaufort-Mackenzie Basin, methane hydrate occurs in 27 wells. Fifteen of these locations coincides with underlying conventional hydrocarbon occurrences. Previous analyses place some of the hydrate occurrences at greater depths than proposed for the methane hydrate stability zone described in this study. Interpretation of geological cross sections reveals that hydrates are related mainly to sandy deltaic and delta-plain deposits in Iperk, Kugmallit, and Reindeer sequences although additional hydrate picks have been inferred in other sequences, such as Richards. Overlying permafrost may act as seal for hydrate accumulations; however, the thickness of permafrost and its related hydrate stability zone fluctuated during geological time. It is interpreted that only in the last tens of thousand of years (i.e., Sangamonian to Holocene), conditions for hydrates changed from nonstable to stable. During Early and Late

  12. Adaptive Spindle Balancing Using Magnetically Levitated Bearings

    BARNEY, PATRICK S.; LAUFFER, JAMES P.; PETTEYS, REBECCA; REDMOND, JAMES M.; SULLIVAN, WILLIAM N.

    1999-01-01

    A technological break through for supporting rotating shafts is the active magnetic bearing (AMB). Active magnetic bearings offer some important advantages over conventional ball, roller or journal bearings such as reduced frictional drag, no physical contact in the bearing, no need for lubricants, compatibility with high vacuum and ultra-clean environments, and ability to control shaft position within the bearing. The disadvantages of the AMB system are the increased cost and complexity, reduced bearing stiffness and the need for a controller. Still, there are certain applications, such as high speed machining, biomedical devices, and gyroscopes, where the additional cost of an AMB system can be justified. The inherent actuator capabilities of the AMB offer the potential for active balancing of spindles and micro-shaping capabilities for machine tools, The work presented in this paper concentrates on an AMB test program that utilizes the actuator capability to dynamically balance a spindle. In this study, an unbalanced AMB spindle system was enhanced with an LMS (Least Mean Squares) algorithm combined with an existing PID (proportional, integral, differential) control. This enhanced controller significantly improved the concentricity of an intentionally unbalanced shaft. The study included dynamic system analysis, test validation, control design and simulation, as well as experimental implementation using a digital LMS controller

  13. Lifestyle Journalism

    From, Unni; Kristensen, Nete Nørgaard

    2013-01-01

    Lifestyle journalism has experienced enormous growth in the media over the past two decades, but scholars in the fields of journalism and communication studies have so far paid relatively little attention to a field that is still sometimes seen as "not real journalism". There is now an urgent need...... for in-depth exploration and contextualisation of this field, with its increasing relevance for 21st century consumer cultures. For the first time, this book presents a wide range of studies which have engaged with the field of lifestyle journalism in order to outline the various political, economic...... of sub-fields such as travel, music, food, health, fashion and personal technology journalism. This volume provides a fascinating account of the different facets of lifestyle journalism, and charts the way forward for a more sustained analysis of the field. This book was originally published as a special...

  14. Correction of compressor critical speed condition through fluid-film bearing optimization

    Spencer, J.W.; Obeid, V.E.

    1985-01-01

    A critical speed condition for an overhung centrifugal compressor was corrected through a relatively minor bearing modification. The resonant condition was evaluated analytically through rotor dynamic analyses (stability and forced response) which included fluid film bearing characterization and rotor model generation (experimentally evaluated by model analysis). The importance of adequate specification, inspection, and analytical characterization, of fluid film bearings are discussed. The effects of unbalance on the stability of plain journal bearings are also commented upon. 1 ref., 6 figs

  15. Ethnographic journalism

    Hermann, Anne Kirstine

    2016-01-01

    require more contextual reporting, ethnographic journalism emerges in American feature journalism. Analyzed holistically, this genre is characterized as the employment of immersion strategies adopted from social science for distinct storytelling purposes. These methods, however, transform conventional......Accounting for emerging journalistic genres is a difficult endeavor not least because there is little agreement as to what constitutes journalism itself. Doing so, however, is essential if we are to recognize changing journalistic doxas. To capture such changes, we must include a holistic framework...... journalistic epistemology, changing it through practice. In turn, the analysis reveals how journalism practices can evolve its troubled philosophical position...

  16. Polar bears, Ursus maritimus

    Rode, Karyn D.; Stirling, Ian

    2017-01-01

    Polar bears are the largest of the eight species of bears found worldwide and are covered in a pigment-free fur giving them the appearance of being white. They are the most carnivorous of bear species consuming a high-fat diet, primarily of ice-associated seals and other marine mammals. They range throughout the circumpolar Arctic to the southernmost extent of seasonal pack ice.

  17. Lubrication analysis of the thrust bearing in the main coolant pump of SMART

    Lee, J. S.; Park, J. S.; Kim, J. H.; Hur, H.; Kim, J. I.

    2001-01-01

    Thrust bearing and journal bearings are installed in the main coolant pump for SMART to support the rotating shaft with proper lubrication. The canned motor type main coolant pumps are arranged vertically on the reactor vessel and especially the MCP bearings are lubricated with water without external lubricating oil supply. Because axial load capacity of the thrust bearing can hardly meet requirement to acquire hydrodynamic or fluid film lubrication state, self-lubrication characteristics of silicon graphite meterials would be needed. Lubricational analysis method for thrust bearing for the main coolant pump of SMART is proposed, and lubricational characteristics of the bearing generated by solving the Reynolds equation are examined in this paper

  18. Self-lubricating fluid bearing assembly

    Kapich, D.D.

    1981-01-01

    A sealed self-lubricating fluid bearing assembly is described for circulating fluid in the form of a gas coolant in a nuclear reactor, the power for the circulator being provided by a shaft located within the primary containment vessel. In such a system the reactor coolant is isolated from the fluid region at the far end of the drive shaft. (U.K.)

  19. Foil Bearing Coating Behavior in CO2

    Walker, Matthew [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Kruizenga, Alan Michael [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Pasch, James Jay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Fleming, Darryn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-08-01

    The Sandia S-CO2 Recompression Closed Brayton Cycle (RCBC) utilizes a series of gas foil bearings in its turbine-alternator-compressors. At high shaft rotational speed these bearings allow the shaft to ride on a cushion of air. Conversely, during startup and shutdown, the shaft rides along the foil bearing surface. Low-friction coatings are used on bearing surfaces in order to facilitate rotation during these periods. An experimental program was initiated to elucidate the behavior of coated bearing foils in the harsh environments of this system. A test configuration was developed enabling long duration exposure tests, followed by a range of analyses relevant to their performance in a bearing. This report provides a detailed overview of this work. The results contained herein provide valuable information in selecting appropriate coatings for more advanced future bearing-rig tests at the newly established test facility in Sandia-NM.

  20. EcoBears

    Nielsen, Nick; Pedersen, Sandra Bleuenn; Sørensen, Jens Ager

    2015-01-01

    In this paper, we introduce the EcoBears concept that aims to augment household appliances with functional and aesthetic features to promote their "use'' and "longevity of use'' to prevent their disposal. The EcoBears also aim to support the communication of environmental issues in the home setting....... We present our initial design and implementation of the EcoBears that consist of two bear modules (a mother and her cub). We also present our preliminary concept validations and lessons learned to be considered for future directions....

  1. Bearing restoration by grinding

    Hanau, H.; Parker, R. J.; Zaretsky, E. V.; Chen, S. M.; Bull, H. L.

    1976-01-01

    A joint program was undertaken by the NASA Lewis Research Center and the Army Aviation Systems Command to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. No bearing failures occurred related to the restoration by grinding process. The risk and cost of a bearing restoration by grinding programs was analyzed. A microeconomic impact analysis was performed.

  2. Big Bear Exploration Ltd. 1998 annual report

    1999-01-01

    During the first quarter of 1998 Big Bear completed a purchase of additional assets in the Rainbow Lake area of Alberta in which light oil purchase was financed with new equity and bank debt. The business plan was to immediately exploit these light oil assets, the result of which would be increased reserves, production and cash flow. Although drilling results in the first quarter on the Rainbow Lake properties was mixed, oil prices started to free fall and drilling costs were much higher than expected. As a result, the company completed a reduced program which resulted in less incremental loss and cash flow than it budgeted for. On April 29, 1998, Big Bear entered into agreement with Belco Oil and Gas Corp. and Moan Investments Ltd. for the issuance of convertible preferred shares at a gross value of $15,750,000, which shares were eventually converted at 70 cents per share to common equity. As a result of the continued plunge in oil prices, the lending value of the company's assets continued to fall, requiring it to take action in order to meet its financial commitments. Late in the third quarter Big Bear issued equity for proceeds of $11,032,000 which further reduced the company's debt. Although the company has been extremely active in identifying and pursuing acquisition opportunities, it became evident that Belco Oil and Gas Corp. and Big Bear did nor share common criteria for acquisitions, which resulted in the restructuring of their relationship in the fourth quarter. With the future of oil prices in question, Big Bear decided that it would change its focus to that of natural gas and would refocus ts efforts to acquire natural gas assets to fuel its growth. The purchase of Blue Range put Big Bear in a difficult position in terms of the latter's growth. In summary, what started as a difficult year ended in disappointment

  3. Character of the contact and biostratigraphical feature of distribution of the microfauna on border between productive series (PS) and underlying upper Miocene sediments of Absheron oil and gas bearing region

    Shikhlinsky, S.A.

    2002-01-01

    Full text: Productive Series (PS) is a basic hydrocarbon object and has a wide distribution in the Absheron Oil and Gas Bearing Region (AOGBR).In the normal stratigraphic sequences PS lays between Akchagylian and Pontian Regiostages (Pontian).From microfauna point of view, PS contains rare native ostracods , fish teeth, otolithes and forams.In situ, in PS, there are 34 of microfauna species present and more than half of them are transitional, which appear in the Upper Miocene and finish the existence in the Akchagylian-Apsheronian sediments.Others taxons are having the strict stratigraphical distribution and very important for the definition of the age of different lithostratones inside PS.Stratigraphical distribution of these species has been tested in numerous natural outcrops and well sections.The large interest for geologists is the boundary between PS and underlying Upper Miocene.The stratigraphic character of the given intermediate complex of sediments depends on paleotectonic conditions and different sections on the way it is expressed differently.In one section, in other-the gradual transition from Pontian to Kalinskaya Suite (KaS).The detailed study of the samples from the numerous old explorationwells drilled before 1972 and from new contract areas located in the Caspian sea, such as Karabakh, Dan Ulduzu, Ashrafi, where sampling was made very detailed, allowed us to discover the characteristic biomarkers and to specify the character of distribution of the microfauna on the Pontian-KaS boundary.The similar contact between KaC and Pontian is observed in the Karabakh field too.KaS here is represented by monotonous carbonated shale, clay and claystone, almost not distinguished from the black Potian shale, with increase at the contact with water.Despite of it, the boundary is precisely beaten by microfauna.In the Pontian sediments we have discovered a characteristic complex of Ostracoda and microscopic Pelecypoda.

  4. New Journalism.

    Fishwick, Marshall, Ed.

    This volume contains a selection of articles which examine, critique, and help to define the phenomenon of new journalism. Included are "Popular Culture and the New Journalism" (Marshall Fishwick), "Entrance" (Richard A. Kallan), "How 'New'?" (George A. Hough III), "Journalistic Primitivism" (Everette E. Dennis), "Wherein Lies the Value?" (Michael…

  5. Zede Journal

    Zede is a scientific journal on engineering science and application, produced under the auspices of the Addis Ababa Institute of Technology, Addis Ababa University. The main objective of the journal is to publish research articles, findings and discussions on engineering sciences, technology and architecture thereby ...

  6. Journal History

    Tanzania Journal of Health Research was established in 1997 as Tanzania Health Research Bulletin. ISSN: 1821-9241. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL · News.

  7. Good journalism or peace journalism?

    David Loyn

    2007-01-01

    This paper argues against the prescriptive notions of Peace Journalism, and in particular its exclusive nature and attempt to define itself as a new orthodoxy. Most of the paper is a critique of the work of Jake Lynch and Annabel McGoldrick, in a book published in 2005, as well as their earlier Reporting the World series. They condemn all other ways of reporting as 'War Journalism, biased in favour of war.' I argue instead that the opposite of Peace Journalism is good journalism. Much of ...

  8. Eastern slopes grizzly bear project : project update

    NONE

    2002-01-01

    This report updates a study to examine the cumulative effects of human activities on the grizzly bears in the central Canadian Rockies. The project was initiated in 1994 to acquire accurate scientific information on the habitat and populations of grizzly bears in the area of the Banff National Park and Kananaskis Country. This area is probably the most heavily used and developed area where the grizzly still survives. The information gathered throughout the course of the study is used to better protect and manage the bears and other sensitive carnivores in the region. Using telemetry, researchers monitored 25 grizzly bears which were radio-collared in a 22,000 square-kilometer area in the upper Bow Valley drainage of the eastern Alberta slopes. The researchers worked with representatives from Husky Oil and Rigel Energy on the development of the Moose Mountain oil and gas field without adversely affecting the grizzly bear population. Information collected over eight years indicates that the grizzly bears have few and infrequent offspring. Using the information gathered thus far, the location of the Moose Mountain to Jumping Pound pipeline was carefully selected, since the bears suffer from high mortality, and the food and cover had already been compromised by the high number of roads, trails and other human activities in the area. The research concluded in November 2001 provides sufficient information to accurately asses the status of the grizzly bear population and habitat. The data will be analyzed and integrated in 2002 into models that reflect the variables affecting grizzly bears and a final report will be published.

  9. 78 FR 2990 - Bear Creek Storage Company, L.L.C.; Notice of Request Under Blanket Authorization

    2013-01-15

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. CP13-34-000] Bear Creek..., 2012, Bear Creek Storage Company, L.L.C. (Bear Creek), 569 Brookwood Village, Suite 749, Birmingham....208, 157.213 and 157.216 of the Commission's Regulations under the Natural Gas Act, and Bear Creek's...

  10. Trophic cascades from wolves to grizzly bears or changing abundance of bears and alternate foods?

    Barber-Meyer, Shannon M

    2015-05-01

    This is a Forum article commenting on: Ripple, W. J., Beschta, R. L., Fortin, J. K., & Robbins, C. T. (2014) Trophic cascades from wolves to grizzly bears in Yellowstone. Journal of Animal Ecology, 83, 223-233. Comparisons Ripple et al. (2014) used to demonstrate increased fruit availability and consumption by grizzly bears post-wolf reintroduction are flawed and tenuous at best. Importantly, a more parsimonious (than trophic cascades) hypothesis, not sufficiently considered by Ripple et al., exists and is better supported by available data I review. Published 2015. This article is a U. S. Government work and is in the public domain in the USA.

  11. Nonlinear Dynamical Analysis for a Plain Bearing

    Ali Belhamra

    2014-03-01

    Full Text Available This paper investigates the nonlinear dynamic behavior for a plain classic bearing (fluid bearing lubricated by a non-Newtonian fluid of a turbo machine rotating with high speed; this type of fluid contains additives viscosity (couple-stress fluid film. The solution of the nonlinear dynamic problem of this type of bearing is determined with a spatial discretisation of the modified Reynolds' equation written in dynamic mode by using the optimized short bearing theory and a temporal discretisation for equations of rotor motion by the help of Euler's explicit diagram. This study analyzes the dynamic behavior of a rotor supported by two couple-stress fluid film journal lubricant enhances the dynamic stability of the rotor-bearing system considerably compared to that obtained when using a traditional Newtonian lubricant. The analysis shows that the dynamic behavior of a shaft which turns with high velocities is strongly nonlinear even for poor eccentricities of unbalance; the presence of parameters of couple stress allows strongly attenuating the will synchrony (unbalance and asynchrony (whipping amplitudes of vibrations of the shaft which supports more severe conditions (large unbalances.

  12. Lifestyle Journalism

    From, Unni; Kristensen, Nete Nørgaard

    2013-01-01

    for in-depth exploration and contextualisation of this field, with its increasing relevance for 21st century consumer cultures. For the first time, this book presents a wide range of studies which have engaged with the field of lifestyle journalism in order to outline the various political, economic......Lifestyle journalism has experienced enormous growth in the media over the past two decades, but scholars in the fields of journalism and communication studies have so far paid relatively little attention to a field that is still sometimes seen as "not real journalism". There is now an urgent need......, social and cultural tensions within it. Taking a comparative view, the collection includes studies covering four continents, including countries such as Australia, China, Norway, Denmark, Singapore, the UK and the USA. While keeping the broader lifestyle field in mind, the chapters focus on a variety...

  13. Ultra-precision bearings

    Wardle, F

    2015-01-01

    Ultra-precision bearings can achieve extreme accuracy of rotation, making them ideal for use in numerous applications across a variety of fields, including hard disk drives, roundness measuring machines and optical scanners. Ultraprecision Bearings provides a detailed review of the different types of bearing and their properties, as well as an analysis of the factors that influence motion error, stiffness and damping. Following an introduction to basic principles of motion error, each chapter of the book is then devoted to the basic principles and properties of a specific type of bearin

  14. Tropical Journal

    Introduction. Nigeria with a national average maternal mortality. 1 ratio (MMR) of 1000/100,000 live births is one of the six countries worldwide that bear the heaviest burden. 2 of maternal mortality. The unbooked expectant. 3 mothers account for majority of these deaths. Currently, higher figures are returned from the rural.

  15. Plain bearing stresses due to forming and oil film pressure

    Burke-Veliz, A; Reed, P A S; Syngellakis, S [University of Southampton, School of Engineering Sciences, Southampton SO17 1BJ (United Kingdom); Wang, D; Wahdy, N; Merritt, D, E-mail: allan.burke@itesm.m [MAHLE Engine Systems UK Ltd, 2 Central park Drive, Rugby CV23 0WE (United Kingdom)

    2009-08-01

    This paper describes a methodology for assessing critical stress ranges arising in automotive plain bearings during engine operations. An industry-produced and run simulation program provides information on oil film pressure and overall bearing deformation during accelerated performance tests. This code performs an elasto-hydrodynamic lubrication analysis accounting for the compliance of the housing and journal. Finite element analyses of a multilayer bearing are performed to assess the conditions responsible for possible fatigue damage over the bearing lining. The residual stresses arising from the forming and fitting process are first assessed. The stress analyses over the engine cycle show the intensity and distribution of cyclic tensile and compressive stresses in the bearing. The location of maximum stress range is found to be consistent with the damage observed in accelerated fatigue tests. Critical zones are identified in the lining for possible fatigue crack initiation and growth studies.

  16. Plain bearing stresses due to forming and oil film pressure

    Burke-Veliz, A; Reed, P A S; Syngellakis, S; Wang, D; Wahdy, N; Merritt, D

    2009-01-01

    This paper describes a methodology for assessing critical stress ranges arising in automotive plain bearings during engine operations. An industry-produced and run simulation program provides information on oil film pressure and overall bearing deformation during accelerated performance tests. This code performs an elasto-hydrodynamic lubrication analysis accounting for the compliance of the housing and journal. Finite element analyses of a multilayer bearing are performed to assess the conditions responsible for possible fatigue damage over the bearing lining. The residual stresses arising from the forming and fitting process are first assessed. The stress analyses over the engine cycle show the intensity and distribution of cyclic tensile and compressive stresses in the bearing. The location of maximum stress range is found to be consistent with the damage observed in accelerated fatigue tests. Critical zones are identified in the lining for possible fatigue crack initiation and growth studies.

  17. Roller bearing geometry design

    Savage, M.; Pinkston, B. H. W.

    1976-01-01

    A theory of kinematic stabilization of rolling cylinders is extended and applied to the design of cylindrical roller bearings. The kinematic stabilization mechanism puts a reverse skew into the rolling elements by changing the roller taper. Twelve basic bearing modification designs are identified amd modeled. Four have single transverse convex curvature in their rollers while eight have rollers which have compound transverse curvature made up of a central cylindrical band surrounded by symmetric bands with slope and transverse curvature. The bearing designs are modeled for restoring torque per unit axial displacement, contact stress capacity, and contact area including dynamic loading, misalignment sensitivity and roller proportion. Design programs are available which size the single transverse curvature roller designs for a series of roller slopes and load separations and which design the compound roller bearings for a series of slopes and transverse radii of curvature. The compound rollers are proportioned to have equal contact stresses and minimum size. Design examples are also given.

  18. DW_BEAR

    Department of Homeland Security — Subset of BEAR (Bi-Weekly Examination Analysis and Reporting) data used for financial audit remediation reporting within the Coast Guard Business Intelligence (CGBI)...

  19. Rolling bearing analysis

    Harris, Tedric A

    2001-01-01

    One of the most well-known experts in the field brings cutting-edge research to practitioners in the new edition of this important reference. Covers the improved mathematical calculations for rolling bearing endurance developed by the American Society of Mechanical Engineers and the Society of Lubrication and Tribology Engineers. Updated with new material on Condition-Based Maintenance, new testing methods, and new bearing materials.

  20. Gear bearing drive

    Mavroidis, Constantinos (Inventor); Vranish, John M. (Inventor); Weinberg, Brian (Inventor)

    2011-01-01

    A gear bearing drive provides a compact mechanism that operates as an actuator providing torque and as a joint providing support. The drive includes a gear arrangement integrating an external rotor DC motor within a sun gear. Locking surfaces maintain the components of the drive in alignment and provide support for axial loads and moments. The gear bearing drive has a variety of applications, including as a joint in robotic arms and prosthetic limbs.

  1. Foothills model forest grizzly bear study : project update

    NONE

    2002-01-01

    This report updates a five year study launched in 1999 to ensure the continued healthy existence of grizzly bears in west-central Alberta by integrating their needs into land management decisions. The objective was to gather better information and to develop computer-based maps and models regarding grizzly bear migration, habitat use and response to human activities. The study area covers 9,700 square km in west-central Alberta where 66 to 147 grizzly bears exist. During the first 3 field seasons, researchers captured and radio collared 60 bears. Researchers at the University of Calgary used remote sensing tools and satellite images to develop grizzly bear habitat maps. Collaborators at the University of Washington used trained dogs to find bear scat which was analyzed for DNA, stress levels and reproductive hormones. Resource Selection Function models are being developed by researchers at the University of Alberta to identify bear locations and to see how habitat is influenced by vegetation cover and oil, gas, forestry and mining activities. The health of the bears is being studied by researchers at the University of Saskatchewan and the Canadian Cooperative Wildlife Health Centre. The study has already advanced the scientific knowledge of grizzly bear behaviour. Preliminary results indicate that grizzlies continue to find mates, reproduce and gain weight and establish dens. These are all good indicators of a healthy population. Most bear deaths have been related to poaching. The study will continue for another two years. 1 fig.

  2. African Journals Online: Ghana

    Items 1 - 27 of 27 ... African Journal of Educational Studies in Mathematics and Sciences .... The Ghana Medical Journal is a peer-reviewed, open access journal ... The Journal of Business Research (JBR) is an International journal published by ...

  3. Pramana – Journal of Physics | Indian Academy of Sciences

    Home; Journals; Pramana – Journal of Physics; Volume 75; Issue 3 ... Chemical potential and internal energy of the noninteracting Fermi gas in ... improved perturbation theory in a quantum chromodynamics inspired potential model.

  4. Experimental and Numerical Simulation of Unbalance Response in Vertical Test Rig with Tilting-Pad Bearings

    Mattias Nässelqvist

    2014-01-01

    Full Text Available In vertically oriented machines with journal bearing, there are no predefined static radial loads, such as dead weight for horizontal rotor. Most of the commercial software is designed to calculate rotordynamic and bearing properties based on machines with a horizontally oriented rotor; that is, the bearing properties are calculated at a static eccentricity. For tilting-pad bearings, there are no existing analytical expressions for bearing parameters and the bearing parameters are dependent on eccentricity and load angle. The objective of this paper is to present a simplified method to perform numerical simulations on vertical rotors including bearing parameters. Instead of recalculating the bearing parameters in each time step polynomials are used to represent the bearing parameters for present eccentricities and load angles. Numerical results are compared with results from tests performed in a test rig. The test rig consists of two guide bearings and a midspan rotor. The guide bearings are 4-pad tilting-pad bearings. Shaft displacement and strains in the bearing bracket are measured to determine the test rig’s properties. The comparison between measurements and simulated results shows small deviations in absolute displacement and load levels, which can be expected due to difficulties in calculating exact bearing parameters.

  5. A Three-Dimensional Foil Bearing Performance Map Applied to Oil-Free Turbomachinery

    2009-04-01

    stress brought on by excessive viscous power loss; therefore a map that graphically relates component and system-level parameters (bearing size, applied...Introduction Foil bearings are self-acting, hydrodynamic gas bearings that use air as their working fluid . Their use in rotating systems eliminates the...weight, maintenance requirements, speed, and temperature limitations associated with conventional oil-lubricated rotor supports (i.e., bearings, dampers

  6. Climate Drives Polar Bear Origins

    In their provocative analysis of northern bears (“Nuclear genomic sequences reveal that polar bears are an old and distinct bear lineage,” Reports, 20 April, p. 344), F. Hailer et al. use independent nuclear loci to show that polar bears originated during the middle Pleistocene, rather than during t...

  7. Watchable Wildlife: The Black Bear

    Lynn L. Rogers

    1992-01-01

    Black bears are the bears people most often encounter. Black bears live in forests over much of North America, unlike grizzlies that live only in Alaska, northern and western Canada, and the northern Rocky Mountains. This brochure presents the latest information on black bear life and how this species responds to an ever-increasing number of campers, hikers, and...

  8. A circumpolar monitoring framework for polar bears

    Vongraven, Dag; Aars, Jon; Amstrup, Steven C.; Atkinson, Stephen N.; Belikov, Stanislav; Born, Erik W.; DeBruyn, T.D.; Derocher, Andrew E.; Durner, George M.; Gill, Michael J.; Lunn, Nicholas J.; Obbard, Martyn E.; Omelak, Jack; Ovsyanikov, Nikita; Peacock, Elizabeth; Richardson, E.E.; Sahanatien, Vicki; Stirling, Ian; Wiig, Øystein

    2012-01-01

    Polar bears (Ursus maritimus) occupy remote regions that are characterized by harsh weather and limited access. Polar bear populations can only persist where temporal and spatial availability of sea ice provides adequate access to their marine mammal prey. Observed declines in sea ice availability will continue as long as greenhouse gas concentrations rise. At the same time, human intrusion and pollution levels in the Arctic are expected to increase. A circumpolar understanding of the cumulative impacts of current and future stressors is lacking, long-term trends are known from only a few subpopulations, and there is no globally coordinated effort to monitor effects of stressors. Here, we describe a framework for an integrated circumpolar monitoring plan to detect ongoing patterns, predict future trends, and identify the most vulnerable polar bear subpopulations. We recommend strategies for monitoring subpopulation abundance and trends, reproduction, survival, ecosystem change, human-caused mortality, human–bear conflict, prey availability, health, stature, distribution, behavioral change, and the effects that monitoring itself may have on polar bears. We assign monitoring intensity for each subpopulation through adaptive assessment of the quality of existing baseline data and research accessibility. A global perspective is achieved by recommending high intensity monitoring for at least one subpopulation in each of four major polar bear ecoregions. Collection of data on harvest, where it occurs, and remote sensing of habitat, should occur with the same intensity for all subpopulations. We outline how local traditional knowledge may most effectively be combined with the best scientific methods to provide comparable and complementary lines of evidence. We also outline how previously collected intensive monitoring data may be sub-sampled to guide future sampling frequencies and develop indirect estimates or indices of subpopulation status. Adoption of this framework

  9. Tribology of alternative bearings.

    Fisher, John; Jin, Zhongmin; Tipper, Joanne; Stone, Martin; Ingham, Eileen

    2006-12-01

    The tribological performance and biological activity of the wear debris produced has been compared for highly cross-linked polyethylene, ceramic-on-ceramic, metal-on-metal, and modified metal bearings in a series of in vitro studies from a single laboratory. The functional lifetime demand of young and active patients is 10-fold greater than the estimated functional lifetime of traditional polyethylene. There is considerable interest in using larger diameter heads in these high demand patients. Highly cross-linked polyethylene show a four-fold reduction in functional biological activity. Ceramic-on-ceramic bearings have the lowest wear rates and least reactive wear debris. The functional biological activity is 20-fold lower than with highly cross-linked polyethylene. Hence, ceramic-on-ceramic bearings address the tribological lifetime demand of highly active patients. Metal-on-metal bearings have substantially lower wear rates than highly cross-linked polyethylene and wear decreases with head diameter. Bedding in wear is also lower with reduced radial clearance. Differential hardness ceramic-on-metal bearings and the application of ceramic-like coatings reduce metal wear and ion levels.

  10. The technology of the bearings used in the nuclear power generation system turbine generator units

    Vialettes, J.M.; Rossato, M.

    1997-01-01

    A bearing consists of all the stationary part which allow the relative motion in rotation or in translation, of a shaft line. Inside the bearing there is a journal bearing with a metallic anti-friction coating (the babbitt metal). The high power turbine generator unit rotors are supported by smooth transversal journal bearings fed with oil which fills the empty space and runs along the shaft. The technologies used for the bearings and the thrust bearings of the turbine generator units and the various shaft lines of the French CP0/CP1- and CP2/1300 MW-type nuclear power plants are described. The experience feedback is then discussed in terms of the dynamics of the shaft line, i.e. vibrational problems, the influence of the alignment and the babbitt metal incidents. (author)

  11. Journalism Forum

    Journalism Educator, 1985

    1985-01-01

    Includes (1) survey results indicating value of traditional journalism and mass communication research; (2) survey results indicating knowledge of grammar, economics, and government are journalists' most valuable resources; (3) methods for teaching listening skills; (4) suggestions for giving public relations students an overview online services;…

  12. New journals

    NN,

    1977-01-01

    Brunonia is the title of a journal that will replace the Contributions from Herbarium Australiense (last no. 17, 1976). Subscriptions Aust. $ 4. annual, Herbarium Australiense, P.O. Box 1600, Canberra City, A.C.T. 2601, Australia. Nature Malaysiana, published quarterly by Tropical Press, 64A Jl.

  13. New journals

    NN,

    1976-01-01

    Applied Ecology Abstracts, compiled and published by Information Retrieval Ltd. 1 Falconberg Court, London W1V 5FG, U.K. A monthly, each issue carrying c. 800 abstracts and author index. Price vol. 1, Jan.-Dec. 1975, surface mail £ 60, airmail £ 73. It is claimed that 4300 journals and other

  14. Thermal conductivity of hydrate-bearing sediments

    Cortes, Douglas D.; Martin, Ana I.; Yun, Tae Sup; Francisca, Franco M.; Santamarina, J. Carlos; Ruppel, Carolyn D.

    2009-01-01

    A thorough understanding of the thermal conductivity of hydrate-bearing sediments is necessary for evaluating phase transformation processes that would accompany energy production from gas hydrate deposits and for estimating regional heat flow based on the observed depth to the base of the gas hydrate stability zone. The coexistence of multiple phases (gas hydrate, liquid and gas pore fill, and solid sediment grains) and their complex spatial arrangement hinder the a priori prediction of the thermal conductivity of hydrate-bearing sediments. Previous studies have been unable to capture the full parameter space covered by variations in grain size, specific surface, degree of saturation, nature of pore filling material, and effective stress for hydrate-bearing samples. Here we report on systematic measurements of the thermal conductivity of air dry, water- and tetrohydrofuran (THF)-saturated, and THF hydrate–saturated sand and clay samples at vertical effective stress of 0.05 to 1 MPa (corresponding to depths as great as 100 m below seafloor). Results reveal that the bulk thermal conductivity of the samples in every case reflects a complex interplay among particle size, effective stress, porosity, and fluid-versus-hydrate filled pore spaces. The thermal conductivity of THF hydrate–bearing soils increases upon hydrate formation although the thermal conductivities of THF solution and THF hydrate are almost the same. Several mechanisms can contribute to this effect including cryogenic suction during hydrate crystal growth and the ensuing porosity reduction in the surrounding sediment, increased mean effective stress due to hydrate formation under zero lateral strain conditions, and decreased interface thermal impedance as grain-liquid interfaces are transformed into grain-hydrate interfaces.

  15. Radioactivity and the French uranium bearing minerals

    Guiollard, P.Ch.; Boisson, J.M.; Leydet, J.C.; Meisser, N.

    1998-01-01

    This special issue of Regne Mineral journal is entirely devoted to the French uranium mining industry. It comprises 4 parts dealing with: the uranium mining industry in France (history, uranium rush, deposits, geologic setting, prosperity and recession, situation in 1998, ore processing); radioactivity and the uranium and its descendants (discovery, first French uranium bearing ores, discovery of radioactivity, radium and other uranium descendants, radium mines, uranium mines, atoms, elements and isotopes, uranium genesis, uranium decay, isotopes in an uranium ore, spontaneous fission, selective migration of radionuclides, radon in mines and houses, radioactivity units, radioprotection standards, new standards and controversies, natural and artificial radioactivity, hazards linked with the handling and collecting of uranium ores, conformability with radioprotection standards, radioactivity of natural uranium minerals); the French uranium bearing minerals (composition, crystal structure, reference, etymology, fluorescence). (J.S.)

  16. Nigerian Journal of Clinical Medicine: Submissions

    Consequently, NJCM, its Editorial Board and LASUTH-ARD bear no legal responsibility for such opinions. Authors are encouraged to send their manuscripts to the LASUTH-ARD Secretariat addressed to: The Editor, Nigerian Journal of Clinical Medicine (NJCM). An electronic copy of the manuscript in Microsoft Word format ...

  17. Partial tooth gear bearings

    Vranish, John M. (Inventor)

    2010-01-01

    A partial gear bearing including an upper half, comprising peak partial teeth, and a lower, or bottom, half, comprising valley partial teeth. The upper half also has an integrated roller section between each of the peak partial teeth with a radius equal to the gear pitch radius of the radially outwardly extending peak partial teeth. Conversely, the lower half has an integrated roller section between each of the valley half teeth with a radius also equal to the gear pitch radius of the peak partial teeth. The valley partial teeth extend radially inwardly from its roller section. The peak and valley partial teeth are exactly out of phase with each other, as are the roller sections of the upper and lower halves. Essentially, the end roller bearing of the typical gear bearing has been integrated into the normal gear tooth pattern.

  18. Compatibility of Anti-Wear Additives with Non-Ferrous Engine Bearing Alloys

    Qu, Jun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhou, Yan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-01-01

    Investigate the compatibility of engine lubricant antiwear (AW) additives, specifically conventional zinc dialkyldithiophosphate (ZDDP) and newly developed ionic liquids (ILs), with selected non-ferrous engine bearing alloys, specifically aluminum and bronze alloys that are commonly used in connecting rod end journal bearings and bushings, to gain fundamental understanding to guide future development of engine lubricants

  19. Journal of Chemical Sciences | Indian Academy of Sciences

    Home; Journals; Journal of Chemical Sciences; Volume 128; Issue 1 ... Ruthenium(II) complexes (1-3) bearing bis-phenolate--heterocyclic carbene ligand were synthesized in good yields by the reaction of imidazolinium proligand (HL) with ... Department of Chemistry, Periyar University, Salem 636 011, Tamil Nadu, India ...

  20. Tilting-Pad Guide Bearing in Large Hydro-unit

    Li-Feng Ma

    2000-01-01

    Full Text Available A new numerical method is proposed for predicting the nonlinearity of tilting-pad guide bearing oilfilm force in the rotor-bearing system in a large hydro-unit. Nonlinear displacement and velocity of the journal center, as well as nonlinear tilting angles and angular velocities of the pads in non-stationary Reynolds equation are taken into account. This method is also suited for other small rotor-bearing system. As an example, the response due to a momentarily created unbalance is Calculated. The nonlinear motion patterns of the pad and journal whirling orbit are obtained. Finally, the nonlinear orbit is compared to the linear one that could be calculated from linear stiffness and damping coefficients. It is shown that there are important differences between those two orbits and that the nonlinear simulation is more accurate.

  1. Feasibility of Applying Active Lubrication to Dynamically Loaded Fluid Film Bearings

    Estupinan, Edgar Alberto; Santos, Ilmar

    2009-01-01

    The feasibility of modifying the dynamics of the thin fluid films of dynamically loaded journal bearings, using different strategies of active lubrication is studied in this work. A significant reduction in the vibration levels, wear and power friction losses, is expected. Particularly, the focus...... of this study is on the analysis of main crankshaft bearings, where the conventional hydrodynamic lubrication is modified by injecting oil at actively controllable pressures, through orifices circumferentially located along the bearing surface....

  2. African Journals Online (AJOL)

    Ethiopian Journal of Education and Sciences; Educational leadership and ... Ethiopian Journal of Education and Sciences; Establishing financial markets in Ethiopia: the environmental foundation, challenges ... South African Actuarial Journal.

  3. Active magnetic bearing for use in compressors and other turbomachinery

    Hennau, J.N.

    1989-01-01

    Active magnetic bearings and dry gas seals are now in operation on quite a number of compressors, turbines and generators, proving than an oil-free system is actually working and that furthermore, it has merits in energy savings, rotor dynamic monitoring and improved reliability. The technology of active magnetic bearing has been developed mainly in France after the Second World War for space application, but soon there appeared the large possibilities in industrial applications starting with the vacuum industry (turbomolecular pump), followed by the machine tool industry (high power and high speed milling and grinding spindles) and the large turbomachinery field (centrifugal compressors, blowers, steam and gas turbines, turbogenerators). Merits of the active magnetic bearing vary from one application to another, but they all derive from the fact that we have no contact between the rotor and the stator and that the electronic control of the bearings can cope with the rotor dynamics and provide useful information on the operating conditions

  4. Magnetically leviated superconducting bearing

    Weinberger, Bernard R.; Lynds, Jr., Lahmer

    1993-01-01

    A magnetically levitated superconducting bearing includes a magnet (2) mounted on a shaft (12) that is rotatable around an axis of rotation and a Type II superconductor (6) supported on a stator (14) in proximity to the magnet (2). The superconductor (6) is positioned so that when it is cooled to its superconducting state in the presence of a magnetic field, it interacts with the magnet (2) to produce an attractive force that levitates the magnet (2) and supports a load on the shaft (12). The interaction between the superconductor (6) and magnet(2) also produces surface screening currents (8) that generate a repulsive force perpendicular to the load. The bearing also has means for maintaining the superconductor at a temperature below its critical temperature (16, 18). The bearing could also be constructed so the magnet (2) is supported on the stator (14) and the superconductor (6) is mounted on the shaft (12). The bearing can be operated by cooling the superconductor (6) to its superconducting state in the presence of a magnetic field.

  5. From Journals

    Nedjeljko Frančula

    2013-06-01

    Full Text Available From the field of cartography and geoinformation, there are journal’s article extracts given which are not cartographic first and whose complete texts are on the Internet, accessible to the members of Croatian academic and research community. Most journals can be accessed through the PERO browser (http://knjiznica.irb.hr/pero/index.php. For the journals not found through this browser, the complete texts of the mentioned articles are available for free on the given web-address. Next to every jo­urnal headline, in the brackets, it is noted which prominent bibliographic and quotation bases it is placed in: CC (Current Contents, SCIE (Science Citati­­on Index Expanded, and SSCI (Social Sc­­­i­ence Citation Index. It should be noted that, for some journals accessible through PERO browser, there is a delay of 6, 12 and even 18 months in accessing the newest issues. This number is given in the brackets next to the journal’s headline.Bullettin of the GSI (Geospatial Information Authority of Japanhttp://www.gsi.go.jp/ENGLISH/page_e30092.htmlK. Kawase: A general formula for calculating meridian arc length and its application to coordinate conversion in the Gauss-Krüger projection, Vol. 59, December 2011.K. Kawase: Concise derivation of extensive coordinate conversion formulae in the Gauss-Krüger pro­jection, Vol. 60, December 2012.Coordinates (A monthly magazine on positioning, navigation and beyond http://mycoordinates.orgT. Nagayama, K. Inaba, T. Hayashi, H: Nakai: Responding to the great east Japan earthquake, 2012, 12.J. SF Fabic: Data integration and sharing for disaster management, 2012, 12.D. Ampatzidis: Datum transformations using exclusively geodetic curvilinear coordinates without height information, 2012, 12.Geomatics and Environmental Engineeringhttp://journals.bg.agh.edu.pl/GEOMATICS/index.phpR. Cellmer, A. Senetra, A. Szczepanska: Land value maps of naturally valuable areas, 2012, 3.Geopolitics (CC, SSCI (12J. Strandsbjerg

  6. Steroid hormone profile in female polar bears (Ursus maritimus)

    Gustavson, Lisa; Jenssen, Bjørn Munro; Bytingsvik, Jenny

    2015-01-01

    The polar bear is an iconic Arctic species, threatened by anthropogenic impacts such as pollution and climate change. Successful reproduction of polar bears depends on a functioning steroid hormone system, which is susceptible to effects of persistent organic pollutants. The present study...... is the first study to report circulating concentrations of nine steroid hormones (i.e., estrogens, androgens and progestagens) in female polar bears (Ursus maritimus). The aim of the study was to investigate the effects of age, condition, location and reproductive status on steroid profile in female polar...... bears. Levels of pregnenolone (PRE), progesterone, androstenedione (AN), dehydroepiandrosterone (DHEA), testosterone, dihydrotestosterone, estrone (E1), 17α-estradiol (αE2) and 17β-estradiol (βE2) were quantified in blood (serum) of free-living female polar bears (n = 15) from Svalbard, Norway, by gas...

  7. An Advanced Microturbine System with Water-Lubricated Bearings

    Susumu Nakano

    2009-01-01

    Full Text Available A prototype of the next-generation, high-performance microturbine system was developed for laboratory evaluation. Its unique feature is its utilization of water. Water is the lubricant for the bearings in this first reported application of water-lubricated bearings in gas turbines. Bearing losses and limitations under usage conditions were found from component tests done on the bearings and load tests done on the prototype microturbine. The rotor system using the water-lubricated bearings achieved stable rotating conditions at a rated rotational speed of 51,000 rpm. An electrical output of 135 kW with an efficiency of more than 33% was obtained. Water was also utilized to improve electrical output and efficiency through water atomizing inlet air cooling (WAC and a humid air turbine (HAT. The operation test results for the WAC and HAT revealed the WAC and HAT operations had significant effects on both electrical output and electrical efficiency.

  8. Compliant Foil Journal Bearings - Investigation of Dynamic Properties

    Larsen, Jon Steffen; Santos, Ilmar

    . The influence of explicit and implicit boundary conditions are also investigated. Theoretical results for pressures, shaft equilibrium positions and film thickness are presented and compared to experimental results [17, 19]. A good agreement between experimental and theoretical results are found for large loads....../compliance of the foil structure is presented. The compliance of the foil structure is incorporated implicitly in the Reynolds equation which is accomplished through a modification of the film gap function [8]. The resulting non-linear equation is perturbed and solved by use of the finite element method following...

  9. Elastohydrodynamics Applied to Active Tilting-Pad Journal Bearings

    Haugaard, Martin Asger; Santos, Ilmar

    2010-01-01

    , but lateral movement is permitted. The servovalve flow is governed by a second order ordinary differential equation, where the right hand side is controlled by an electronic input signal. The constitutive flow-pressure relationship of the injection orifices is that of a fully developed laminar velocity....... The oil film pressure and flow are considered to follow the modified Reynolds equation, which includes the contribution from controllable radial oil injection. The Reynolds equation is solved using a two-dimensional finite element mesh. The rotor is considered to be rigid in terms of shape and size...... profile and the servovalve is introduced into the system of equations by a mass conservation consideration. The Reynolds equation is linearized with respect to displacements and velocities of the nodal degrees of freedom. When all nodal points satisfy static equilibrium, the system of equations...

  10. On a mathematical model of journal bearing lubrication

    Lanzendörfer, Martin; Stebel, Jan

    2011-01-01

    Roč. 81, č. 11 (2011), s. 2456-2470 ISSN 0378-4754 R&D Projects: GA ČR GA201/09/0917 Grant - others:GA ČR(CZ) GA201/06/0352 Institutional research plan: CEZ:AV0Z10300504; CEZ:AV0Z10190503 Keywords : existence of weak solutions * incompressible non-Newtonian fluids * pressure and shear rate dependent viscosity * inflow/outflow boundary conditions * filtration boundary conditions Subject RIV: BK - Fluid Dynamics Impact factor: 0.738, year: 2011

  11. Wolves trigger a trophic cascade to berries as alternative food for grizzly bears.

    Ripple, William J; Beschta, Robert L; Fortin, Jennifer K; Robbins, Charles T

    2015-05-01

    This is a Forum article in response to: Barber-Meyer, S. (2015) Trophic cascades from wolves to grizzly bears or changing abundance of bears and alternate foods? Journal of Animal Ecology, 83, doi: 10.1111/1365-2656.12338. We used multiple data sets and study areas as well as several lines of evidence to investigate potential trophic linkages in Yellowstone National Park. Our results suggest that a trophic cascade from wolves to elk to berry production to berry consumption by grizzly bears may now be underway in the Park. © 2015 The Authors. Journal of Animal Ecology © 2015 British Ecological Society.

  12. African Journals Online (AJOL)

    Featured Country: Ghana, Featured Journal: Journal of Business Research. Most recent issues on AJOL: Vol 13 (2017). African Journal of Educational Studies in Mathematics and Sciences. Vol 7 (2017) ... Vol 6, No 2 (2014). Journal of ...

  13. Tanzania Medical Journal

    The journal publishes any contribution that advances medical science or ... these core objectives the journal publishes papers on original scientific research, short ... The Tanzania Medical Journal is an international Journal - ISSN: 0856-0719 ...

  14. African Crop Science Journal

    African Crop Science Journal. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 1, No 2 (1993) >. Log in or Register to get access to full text downloads.

  15. African Crop Science Journal

    African Crop Science Journal. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 22 (2014) >. Log in or Register to get access to full text downloads.

  16. SA Journal of Radiology

    SA Journal of Radiology. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 19, No 2 (2015) >. Log in or Register to get access to full text downloads.

  17. SA Journal of Radiology

    SA Journal of Radiology. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 21, No 1 (2017) >. Log in or Register to get access to full text downloads.

  18. Ethiopian Veterinary Journal

    Ethiopian Veterinary Journal. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 15, No 1 (2011) >. Log in or Register to get access to full text downloads.

  19. Nigerian Journal of Physics

    Nigerian Journal of Physics. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 18, No 2 (2006) >. Log in or Register to get access to full text downloads.

  20. Nigerian Journal of Physics

    Nigerian Journal of Physics. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 20, No 1 (2008) >. Log in or Register to get access to full text downloads.

  1. Nigerian Journal of Physics

    Nigerian Journal of Physics. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 18, No 1 (2006) >. Log in or Register to get access to full text downloads.

  2. Actuators for Active Magnetic Bearings

    Eric H. Maslen

    2017-10-01

    Full Text Available The literature of active magnetic bearing (AMB technology dates back to at least 1937 when the earliest work that clearly describes an active magnetic bearing system was published by Jesse Beams [...

  3. Delayed child-bearing.

    Johnson, Jo-Ann; Tough, Suzanne

    2012-01-01

    To provide an overview of delayed child-bearing and to describe the implications for women and health care providers. Delayed child-bearing, which has increased greatly in recent decades, is associated with an increased risk of infertility, pregnancy complications, and adverse pregnancy outcome. This guideline provides information that will optimize the counselling and care of Canadian women with respect to their reproductive choices. Maternal age is the most important determinant of fertility, and obstetric and perinatal risks increase with maternal age. Many women are unaware of the success rates or limitations of assisted reproductive technology and of the increased medical risks of delayed child-bearing, including multiple births, preterm delivery, stillbirth, and Caesarean section. This guideline provides a framework to address these issues. Studies published between 2000 and August 2010 were retrieved through searches of PubMed and the Cochrane Library using appropriate key words (delayed child-bearing, deferred pregnancy, maternal age, assisted reproductive technology, infertility, and multiple births) and MeSH terms (maternal age, reproductive behaviour, fertility). The Internet was also searched using similar key words, and national and international medical specialty societies were searched for clinical practice guidelines and position statements. Data were extracted based on the aims, sample, authors, year, and results. The quality of evidence was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table 1). The Society of Obstetricians and Gynaecologists of Canada. RECOMMENDATIONS 1. Women who delay child-bearing are at increased risk of infertility. Prospective parents, especially women, should know that their fecundity and fertility begin to decline significantly after 32 years of age. Prospective parents should know that assisted reproductive technologies cannot guarantee a live birth or completely

  4. Government Risk-Bearing

    1993-01-01

    The u.s. government bulks large in the nation's financial markets. The huge volume of government-issued and -sponsored debt affects the pricing and volume ofprivate debt and, consequently, resource allocation between competing alternatives. What is often not fully appreciated is the substantial influence the federal government wields overresource allocation through its provisionofcreditandrisk-bearing services to the private economy. Because peopleand firms generally seekto avoid risk, atsomeprice they are willing to pay another party to assume the risk they would otherwise face. Insurance companies are a class of private-sector firms one commonly thinks of as providing these services. As the federal government has expanded its presence in the U.S. economy during this century, it has increasingly developed programs aimed at bearing risks that the private sector either would not take on at any price, or would take on but atapricethoughtto besogreatthatmostpotentialbeneficiarieswouldnotpurchase the coverage. To...

  5. Passive magnetic bearing system

    Post, Richard F.

    2014-09-02

    An axial stabilizer for the rotor of a magnetic bearing provides external control of stiffness through switching in external inductances. External control also allows the stabilizer to become a part of a passive/active magnetic bearing system that requires no external source of power and no position sensor. Stabilizers for displacements transverse to the axis of rotation are provided that require only a single cylindrical Halbach array in its operation, and thus are especially suited for use in high rotation speed applications, such as flywheel energy storage systems. The elimination of the need of an inner cylindrical array solves the difficult mechanical problem of supplying support against centrifugal forces for the magnets of that array. Compensation is provided for the temperature variation of the strength of the magnetic fields of the permanent magnets in the levitating magnet arrays.

  6. Stacked magnet superconducting bearing

    Rigney, T.K. II; Saville, M.P.

    1993-01-01

    A superconducting bearing is described, comprising: a plurality of permanent magnets magnetized end-to-end and stacked side-by-side in alternating polarity, such that flux lines flow between ends of adjacent magnets; isolating means, disposed between said adjacent magnets, for reducing flux leakage between opposing sides of said adjacent magnets; and a member made of superconducting material having at least one surface in communication with said flux lines

  7. Radium bearing waste disposal

    Tope, W.G.; Nixon, D.A.; Smith, M.L.; Stone, T.J.; Vogel, R.A.; Schofield, W.D.

    1995-01-01

    Fernald radium bearing ore residue waste, stored within Silos 1 and 2 (K-65) and Silo 3, will be vitrified for disposal at the Nevada Test Site (NTS). A comprehensive, parametric evaluation of waste form, packaging, and transportation alternatives was completed to identify the most cost-effective approach. The impacts of waste loading, waste form, regulatory requirements, NTS waste acceptance criteria, as-low-as-reasonably-achievable principles, and material handling costs were factored into the recommended approach

  8. Magnetic translator bearings

    Hockney, Richard L. (Inventor); Downer, James R. (Inventor); Eisenhaure, David B. (Inventor); Hawkey, Timothy J. (Inventor); Johnson, Bruce G. (Inventor)

    1990-01-01

    A magnetic bearing system for enabling translational motion includes a carriage and a shaft for movably supporting the carriage; a first magnetic bearing fixed to one of the carriage and shaft and slidably received in a first channel of the other of the carriage and shaft. The first channel is generally U shaped with two side walls and a back wall. The magnetic bearing includes a pair of spaced magnetic pole pieces, each pole piece having a pair of electromagnetic coils mounted on poles on opposite ends of the pole piece proximate the side walls, and a third electromagnetic coil mounted on a pole of the pole piece proximate the backwall; a motion sensor for sensing translational motion along two axes and rotationally about three axes of the carriage and shaft relative to each other; and a correction circuit responsive to the sensor for generating a correction signal to drive the coils to compensate for any misalignment sensed between the carriage and the shaft.

  9. Good journalism or peace journalism?

    David Loyn

    2007-10-01

    Full Text Available This paper argues against the prescriptive notions of Peace Journalism, and in particular its exclusive nature and attempt to define itself as a new orthodoxy. Most of the paper is a critique of the work of Jake Lynch and Annabel McGoldrick, in a book published in 2005, as well as their earlier Reporting the World series. They condemn all other ways of reporting as 'War Journalism, biased in favour of war.' I argue instead that the opposite of Peace Journalism is good journalism. Much of this Peace Journalism argument is derived from the work of Johan Galtung, who accuses 'war journalists' of reporting war in an enclosed space and time, with no context, concealing peace initiatives and making wars 'opaque/secret.' Galtung specifically calls on journalists as part of their mission to search out peace proposals which might begin as something small and beneath notice, but which might then be picked up and owned by politicians as their own. My response is clear and simple: creating peacemaking politicians is not the business of a reporter. I examine the traditional journalistic methods of using objectivity to get at a version of the truth. I concede that perfect truth is unattainable, (and paradoxically the tool of objectivity we use to get there is slippery too. I conclude that a more quotidian truth, or 'truthfulness' is though a manageable goal. I engage with philosophers who examine objectivity, concluding with the assistance of Thomas Nagel that it does still have a value. Nagel's account also has the merit of explaining how practices such as peace-reporting are bound to be less objective than alternatives, 'since they commit themselves to the adoption of particular perspectives, in effect giving up on the ideal of stripping away as much…as possible.' I examine the responses of the so-called 'journalism of attachment' framed as a desire of journalists faced by the horrors of Bosnia to cast off impartiality and emotional detachment and take

  10. A constitutive model for the forces of a magnetic bearing including eddy currents

    Taylor, D. L.; Hebbale, K. V.

    1993-01-01

    A multiple magnet bearing can be developed from N individual electromagnets. The constitutive relationships for a single magnet in such a bearing is presented. Analytical expressions are developed for a magnet with poles arranged circumferencially. Maxwell's field equations are used so the model easily includes the effects of induced eddy currents due to the rotation of the journal. Eddy currents must be included in any dynamic model because they are the only speed dependent parameter and may lead to a critical speed for the bearing. The model is applicable to bearings using attraction or repulsion.

  11. Bearing for liquid metal pump

    Dickinson, R.J.; Pennell, W.E.; Wasko, J.

    1984-01-01

    A liquid metal pump bearing support comprises a series of tangentially oriented spokes that connect the bearing cylinder to the pump internals structure. The spokes may be arranged in a plurality of planes extending from the bearing cylinder to the pump internals with the spokes in one plane being arranged alternately with those in the next plane. The bearing support structure provides the pump with sufficient lateral support for the bearing structure together with the capability of accommodating differential thermal expansion without adversely affecting pump performance

  12. Pramana – Journal of Physics | Indian Academy of Sciences

    Home; Journals; Pramana – Journal of Physics. Makoto Kobayashi. Articles written in Pramana – Journal of Physics. Volume 69 Issue 6 December 2007 pp 981-987 Tracking and Vertexing. A beam test of prototype time projection chamber using micro-pattern gas detectors at KEK · Makoto Kobayashi on behalf of part of the ...

  13. Pramana – Journal of Physics | Indian Academy of Sciences

    Home; Journals; Pramana – Journal of Physics. Rangan Lahiri. Articles written in Pramana – Journal of Physics. Volume 62 Issue 5 May 2004 pp 1015-1028 Research Articles. Brownian motion in a classical ideal gas: A microscopic approach to Langevin's equation · Rangan Lahiri Arvind Anirban Sain · More Details ...

  14. Pramana – Journal of Physics | Indian Academy of Sciences

    Home; Journals; Pramana – Journal of Physics. C N Kumar. Articles written in Pramana – Journal of Physics. Volume 74 Issue 1 January 2010 pp 83-96 Research Articles. Density excitations of a harmonically trapped ideal gas · Jai Carol Cruz C N Kumar K N Pathak J Bosse · More Details Abstract Fulltext PDF.

  15. Journal of Chemical Sciences | Indian Academy of Sciences

    Home; Journals; Journal of Chemical Sciences. P K Chattaraj. Articles written in Journal of Chemical Sciences. Volume 115 Issue 3 June 2003 pp 195-218 Physical and Theoretical. Chemical reactivity of the compressed noble gas atoms and their reactivity dynamics during collisions with protons · P K Chattaraj B Maiti U ...

  16. Journal of Chemical Sciences | Indian Academy of Sciences

    Home; Journals; Journal of Chemical Sciences. SUDIP PAN. Articles written in Journal of Chemical Sciences. Volume 128 Issue 10 October 2016 pp 1537-1548 Regular Article. A computational study on structure, stability and bonding in Noble Gas bound metal Nitrates, Sulfates and Carbonates (Metal = Cu, Ag, Au).

  17. Journal of Earth System Science | Indian Academy of Sciences

    Home; Journals; Journal of Earth System Science. P Senthil Kumar. Articles written in Journal of Earth System Science. Volume 119 Issue 5 October 2010 pp 745-751. Soil-gas helium and surface-waves detection of fault zones in granitic bedrock · G K Reddy T Seshunarayana Rajeev Menon P Senthil Kumar · More Details ...

  18. Resonance – Journal of Science Education | Indian Academy of ...

    Home; Journals; Resonance – Journal of Science Education. W Kohn. Articles written in Resonance – Journal of Science Education. Volume 22 Issue 8 August 2017 pp 809-811 Classics. Inhomogeneous Electron Gas · P Hohenberg W Kohn · More Details Abstract Fulltext PDF ...

  19. Journal of Chemical Sciences | Indian Academy of Sciences

    Home; Journals; Journal of Chemical Sciences. R H DUNCAN LYNGDOH. Articles written in Journal of Chemical Sciences. Volume 128 Issue 5 May 2016 pp 681-693 Regular Articles. Uncatalyzed thermal gas phase aziridination of alkenes by organic azides. Part I: Mechanisms with discrete nitrene species · S PREMILA ...

  20. 77 FR 70423 - Black Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC...

    2012-11-26

    ... Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC; Notice of..., 2012, Black Bear Hydro Partners, LLC, sole licensee (transferor) and Black Bear Development Holdings, LLC and Black Bear SO, LLC (transferees) filed an application for the partial the transfer of licenses...

  1. Introgressive hybridization: brown bears as vectors for polar bear alleles.

    Hailer, Frank

    2015-03-01

    The dynamics and consequences of introgression can inform about numerous evolutionary processes. Biologists have therefore long been interested in hybridization. One challenge, however, lies in the identification of nonadmixed genotypes that can serve as a baseline for accurate quantification of admixture. In this issue of Molecular Ecology, Cahill et al. (2015) analyse a genomic data set of 28 polar bears, eight brown bears and one American black bear. Polar bear alleles are found to be introgressed into brown bears not only near a previously identified admixture zone on the Alaskan Admiralty, Baranof and Chichagof (ABC) Islands, but also far into the North American mainland. Elegantly contrasting admixture levels at autosomal and X chromosomal markers, Cahill and colleagues infer that male-biased dispersal has spread these introgressed alleles away from the Late Pleistocene contact zone. Compared to a previous study on the ABC Island population in which an Alaskan brown bear served as a putatively admixture-free reference, Cahill et al. (2015) utilize a newly sequenced Swedish brown bear as admixture baseline. This approach reveals that brown bears have been impacted by introgression from polar bears to a larger extent (up to 8.8% of their genome), than previously known, including the bear that had previously served as admixture baseline. No evidence for introgression of brown bear into polar bear is found, which the authors argue could be a consequence of selection. Besides adding new exciting pieces to the puzzle of polar/brown bear evolutionary history, the study by Cahill and colleagues highlights that wildlife genomics is moving from analysing single genomes towards a landscape genomics approach. © 2015 John Wiley & Sons Ltd.

  2. When captive customers bear the risk

    Michaels, R.J.

    1993-01-01

    Before open access, long-term contracts between gas producers, pipelines, and local distribution companies (LDCs) were the rule. Since then, spot trading has dominated the gas market. Spot prices govern short-term transactions and often determine adjustments in longer-term contracts. Experts have repeatedly predicted a return to long-term fixed-price (LTFP) contracts. (open-quotes Fixedclose quotes means unrelated to spot prices, but not necessarily frozen.) They have perceived spot dealing as a response to temporary chaos, or as the consequence of a open-quotes bubbleclose quotes of deliverable gas that would soon vanish. The Federal Energy Regulatory Commission staff's analysis of Order 636 anticipates that the order will foster long-term contracts. But as the dust settles, the reign of spot gas continues. LTFP gas contracts certainly appear superior to spot trades. In readily, LTFP contracts are inferior at almost every turn. Paradoxically, they are riskier than spot transactions. If LTFP contracts were worthwhile, most large gas buyers would use them. Instead, those buyers purchase spot gas and hedge it with futures and options. Electric utilities, nonutility generators, and LDCs are virtually the only users of LTFP contracts. Unlike other gas buyers, utilities can shift risk onto their customers through automatic adjustments in their regulated rates. If ratepayers were not captives, they would not bear the added risk of LTFP contracts without compensation. LTFP contracts are a thing of the past, a security blanket for utilities that is paid for by their customers. If regulators do not put an end to LTFP contracts, competition will. Customers with choices will not hold still for LTFP pass-throughs, as has become evident in LDC gas bypass

  3. Self lubricating fluid bearings

    Kapich, D.D.

    1980-01-01

    The invention concerns self lubricating fluid bearings, which are used in a shaft sealed system extending two regions. These regions contain fluids, which have to be isolated. A first seal is fluid tight for the first region between the carter shaft and the shaft. The second seal is fluid tight between the carter and the shaft, it communicates with the second region. The first fluid region is the environment surrounding the shaft carter. The second fluid region is a part of a nuclear reactor which contains the cooling fluid. The shaft is conceived to drive a reactor circulating and cooling fluid [fr

  4. International Journal of Development and Policy Studies: Journal ...

    International Journal of Development and Policy Studies: Journal Sponsorship. Journal Home > About the Journal > International Journal of Development and Policy Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

  5. East African Journal of Public Health: Journal Sponsorship

    East African Journal of Public Health: Journal Sponsorship. Journal Home > About the Journal > East African Journal of Public Health: Journal Sponsorship. Log in or Register to get access to full text downloads.

  6. Scopus: Journal of East African Ornithology: Journal Sponsorship

    Scopus: Journal of East African Ornithology: Journal Sponsorship. Journal Home > About the Journal > Scopus: Journal of East African Ornithology: Journal Sponsorship. Log in or Register to get access to full text downloads.

  7. Western Indian Ocean Journal of Marine Science: Journal ...

    Western Indian Ocean Journal of Marine Science: Journal Sponsorship. Journal Home > About the Journal > Western Indian Ocean Journal of Marine Science: Journal Sponsorship. Log in or Register to get access to full text downloads.

  8. African Journal of Oral Health Sciences: Journal Sponsorship

    African Journal of Oral Health Sciences: Journal Sponsorship. Journal Home > About the Journal > African Journal of Oral Health Sciences: Journal Sponsorship. Log in or Register to get access to full text downloads.

  9. South African Journal of Bioethics and Law: Journal Sponsorship

    South African Journal of Bioethics and Law: Journal Sponsorship. Journal Home > About the Journal > South African Journal of Bioethics and Law: Journal Sponsorship. Log in or Register to get access to full text downloads.

  10. Creative Artist: A Journal of Theatre and Media Studies: Journal ...

    Creative Artist: A Journal of Theatre and Media Studies: Journal Sponsorship. Journal Home > About the Journal > Creative Artist: A Journal of Theatre and Media Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

  11. African Journal of Finance and Management: Journal Sponsorship

    African Journal of Finance and Management: Journal Sponsorship. Journal Home > About the Journal > African Journal of Finance and Management: Journal Sponsorship. Log in or Register to get access to full text downloads.

  12. Journal of Research in Forestry, Wildlife and Environment: Journal ...

    Journal of Research in Forestry, Wildlife and Environment: Journal Sponsorship. Journal Home > About the Journal > Journal of Research in Forestry, Wildlife and Environment: Journal Sponsorship. Log in or Register to get access to full text downloads.

  13. Lagos Journal of Library and Information Science: Journal ...

    Lagos Journal of Library and Information Science: Journal Sponsorship. Journal Home > About the Journal > Lagos Journal of Library and Information Science: Journal Sponsorship. Log in or Register to get access to full text downloads.

  14. Science, Technology and Arts Research Journal: Journal Sponsorship

    Science, Technology and Arts Research Journal: Journal Sponsorship. Journal Home > About the Journal > Science, Technology and Arts Research Journal: Journal Sponsorship. Log in or Register to get access to full text downloads.

  15. South African Journal of Sports Medicine: Journal Sponsorship

    South African Journal of Sports Medicine: Journal Sponsorship. Journal Home > About the Journal > South African Journal of Sports Medicine: Journal Sponsorship. Log in or Register to get access to full text downloads.

  16. Tanzania Journal of Forestry and Nature Conservation: Journal ...

    Tanzania Journal of Forestry and Nature Conservation: Journal Sponsorship. Journal Home > About the Journal > Tanzania Journal of Forestry and Nature Conservation: Journal Sponsorship. Log in or Register to get access to full text downloads.

  17. West African Journal of Applied Ecology: Journal Sponsorship

    West African Journal of Applied Ecology: Journal Sponsorship. Journal Home > About the Journal > West African Journal of Applied Ecology: Journal Sponsorship. Log in or Register to get access to full text downloads.

  18. Journal of History and Diplomatic Studies: Journal Sponsorship

    Journal of History and Diplomatic Studies: Journal Sponsorship. Journal Home > About the Journal > Journal of History and Diplomatic Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

  19. Journal of Computer Science and Its Application: Journal Sponsorship

    Journal of Computer Science and Its Application: Journal Sponsorship. Journal Home > About the Journal > Journal of Computer Science and Its Application: Journal Sponsorship. Log in or Register to get access to full text downloads.

  20. Nigeria Journal of Pure and Applied Physics: Journal Sponsorship

    Nigeria Journal of Pure and Applied Physics: Journal Sponsorship. Journal Home > About the Journal > Nigeria Journal of Pure and Applied Physics: Journal Sponsorship. Log in or Register to get access to full text downloads.

  1. Journal of the Nigerian Association of Mathematical Physics: Journal ...

    Journal of the Nigerian Association of Mathematical Physics: Journal Sponsorship. Journal Home > About the Journal > Journal of the Nigerian Association of Mathematical Physics: Journal Sponsorship. Log in or Register to get access to full text downloads.

  2. OGIRISI: a New Journal of African Studies: Journal Sponsorship

    OGIRISI: a New Journal of African Studies: Journal Sponsorship. Journal Home > About the Journal > OGIRISI: a New Journal of African Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

  3. Fluid-film bearings: a finite element method of analysis

    Pururav, T.; Soni, R.S.; Kushwaha, H.S.; Mahajan, S.C.

    1995-01-01

    Finite element method (FEM) has become a very popular technique for the analysis of fluid-film bearings in the last few years. These bearings are extensively used in nuclear industry applications such as in moderator pumps and main coolant pumps. This report gives the methodology for the solution of Reynold's equation using FEM and its implementation in FE software LUBAN developed in house. It also deals with the mathematical basis and algorithm to account for the cavitation phenomena which makes these problems non-linear in nature. The dynamic coefficients of bearings are evaluated by one-step approach using variational principles. These coefficients are useful for the dynamic characterisation of fluid-film bearings. Several problems have been solved using this code including two real life problems, a circumferentially grooved journal bearing for which experimental results are available and the bearing of moderator pump of 500 MWe PHWR, have been solved. The results obtained for sample problems are in good agreement with the published literature. (author). 9 refs., 14 figs., 5 tabs., 2 ills

  4. Methodological guide for communities greenhouse gas emission assessments according to the article 75 of the 2010-788 law of July 12, 2010 bearing national commitment for the environment (ENE)

    2011-01-01

    After some basic definitions, this document describes the approach chosen to count greenhouse gas emissions as they are defined in the law: identification of emissions to be counted in greenhouse gas emission assessments, wider framework of district climate-energy plans. It describes how the general methodology is implemented, and more particularly in the case of a district or community. One can find in appendix: the strategic framework for regional climate air and energy scheme, a list of possible methodological principles within the frame of a district approach, and the case of emissions related to waste processing and of associated avoided emissions

  5. Archives: Nigerian Veterinary Journal

    Items 1 - 49 of 49 ... Archives: Nigerian Veterinary Journal. Journal Home > Archives: Nigerian Veterinary Journal. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives. 1 - 49 of 49 Items ...

  6. ChemSearch Journal

    Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives. Journal Homepage Image. Chemsearch Journal is a peer – reviewed journal that publishes original research work, scientific papers and technical reports in all the field of Chemistry (pure science, agriculture, environmental science, ...

  7. Journalism Beyond High School.

    Turner, Sally

    2001-01-01

    Discusses the shift from high school journalism to college journalism for students. Describes the role of the high school journalism advisor in that process. Offers checklists for getting to know a college publication. Outlines ways high school journalism teachers can take advantage of journalism resources available at local colleges and…

  8. Archives: Ethiopian Veterinary Journal

    Items 1 - 16 of 16 ... Archives: Ethiopian Veterinary Journal. Journal Home > Archives: Ethiopian Veterinary Journal. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives. 1 - 16 of 16 Items ...

  9. Archives: Malawi Medical Journal

    Items 1 - 50 of 72 ... Archives: Malawi Medical Journal. Journal Home > Archives: Malawi Medical Journal. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives. 1 - 50 of 72 Items, 1 2 > >> ...

  10. African Journals Online (AJOL)

    African Journals OnLine (AJOL) is the world's largest and pre-eminent collection of peer-reviewed, ... Featured Country: Ethiopia, Featured Journal: AFRREV STECH: An International Journal of Science and Technology ... Journal of Agriculture, Forestry and the Social Sciences. Vol 38, No 2 ... Journal of Applied Biosciences.

  11. Malawi Medical Journal

    for Researchers · for Journals · for Authors · for Policy Makers · about Open Access · Journal Quality. 521 African Journals. Browse By Category · Browse Alphabetically · Browse By Country · List All Titles · Free To Read Titles This Journal is Open Access. Featuring journals from 32 Countries: Algeria (5); Benin (2); Botswana ...

  12. African Journals Online (AJOL)

    Shakespeare in Southern Africa. Vol 28, No 1 (2018). Ethiopian Journal of Agricultural Sciences. Vol 15, No 1 (2018). SAHARA-J: Journal of Social Aspects of HIV/AIDS. Vol 20, No 10 (2017). Nigerian Journal of Clinical Practice. Vol 108, No 2 (2018). South African Medical Journal. Vol 21, No 1 (2018). Nigerian Journal of ...

  13. Nigerian Food Journal: Contact

    Nigerian Food Journal. ... Nigerian Food Journal: Contact. Journal Home > About the Journal > Nigerian Food Journal: Contact. Log in or Register to get access to full text downloads. ... Mailing Address. Department of Food Science and Technology University of Agriculture, Makurdi, Nigeria ...

  14. Innovation: About this journal

    for Researchers · for Journals · for Authors · for Policy Makers · about Open Access · Journal Quality. 521 African Journals. Browse By Category · Browse Alphabetically · Browse By Country · List All Titles · Free To Read Titles This Journal is Open Access. Featuring journals from 32 Countries: Algeria (5); Benin (2); Botswana ...

  15. African Journals Online (AJOL)

    African Journal of Oral Health. Vol 35, No 1-2 (2017). Egyptian Journal of Biochemistry and Molecular Biology. Vol 7, No 3 (2017). African Journal of Chemical Education. Vol 8, No 2 (2017): Journal of Language, Technology & Entrepreneurship in Africa. Journal of Language, Technology & Entrepreneurship in Africa.

  16. Nanoprecipitation in bearing steels

    Barrow, A.T.W.; Rivera-Diaz-del-Castillo, P.E.J.

    2011-01-01

    θ-phase is the main hardening species in bearing steels and appears in both martensitically and bainitically hardened microstructures. This work presents a survey of the microstrucural features accompanying nanoprecipitation in bearing steels. Nanoprecipitate structures formed in 1C-1.5Cr wt.% with additions of Cr, Mn, Mo, Si and Ni are studied. The work is combined with thermodynamic calculations and neural networks to predict the expected matrix composition, and whether this will transform martensitically or bainitically. Martensite tetragonality, composition and the amount of retained austenite are related to hardness and the type of nanoprecipitate structures in martensitic grades. The θ-phase volume fraction, the duration of the bainite to austenite transformation and the amount of retained austenite are related to hardness and a detailed quantitative description of the precipitate nanostructures. Such description includes compositional studies using energy-dispersive spectroscopy, which shows that nanoprecipitate formation takes place under paraequilibrium. Special attention is devoted to a novel two-step bainite tempering process which shows maximum hardness; we prove that this is the most effective process for incorporating solute into the precipitates, which are finer than those resulting from one-step banitic transformation processes.

  17. Superconducting bearings in flywheels

    Coombs, T.A.; Campbell, A.M.; Ganney, I.; Lo, W. [Cambridge Univ. (United Kingdom). Interdisciplinary Research Centre in Superconductivity (IRC); Twardowski, T. [International Energy Systems, Chester High Road, Neston, South Wirral (United Kingdom); Dawson, B. [British Nuclear Fuels, Capenhurst, South Wirral (United Kingdom)

    1998-05-01

    Investigations are being carried out into the use of superconducting magnetic bearings to levitate energy storage flywheels. In a planned program of work, Cambridge University are aiming to produce a practical bearing system for Pirouette(TM). The Pirouette(TM) system is designed to provide 5 kWh of recoverable energy which is currently recoverable at a rate of 5 kW (future revisions will provide up to 50 kW). IES (a British Nuclear Fuels subsidiary) the owners of the Pirouette(TM) machine have supplied Cambridge with a flywheel. This flywheel weighs >40 kg and is being levitated using an Evershed-type arrangement in which the superconductor is being used to stabilize the interaction between two magnets. To date we have demonstrated stable levitation in static and low speed tests in a rig designed for low speeds of rotation in air. A second rig which is currently under construction at BNFL will run in vacuum at speeds of up to 50 (orig.) 5 refs.

  18. Comparison Between Predictions and Measurements of Performance Characteristics for an Eight Pocket Hybrid (Combination Hydrostatic and Hydrodynamic) Thrust Bearing

    2008-12-03

    STB stainless steel housing. Drive End Thrust Collar Free End Splash Guard Slave Thrust Bearing Face STB Flange Figure 12: Exploded view of slave...Bulk Flow Analysis of Hybrid Thrust Bearing for Process Fluid Applications.” ASME Trans., Journal of Tribology , January, Vol. 122 (1), pp. 170-180...ASME Journal of Tribology , Vol. 123, pp. 768-776 [5] San Andrés, L., (2006), “MEEN 626 Notes 2 Derivation of the Classical Reynolds Equation for

  19. A Two-Dimensional Post-Stack Seismic Inversion for Acoustic Impedance of Gas and Hydrate Bearing Deep-Water Sediments Within the Continental Slope of the Ulleung Basin, East Sea, Korea

    Keumsuk Lee

    2013-01-01

    Full Text Available A post-stack inversion of 2D seismic data was conducted to estimate the spatial distribution of acoustic impedance associated with gas and hydrates in the Ulleung Basin, East Sea, Korea constrained by logs from three boreholes drilled on its continental margin. A model-based inversion was applied to a Plio-Quaternary succession composed of alternations of unconsolidated mass-flow deposits/turbidites. A comparison of seismic reflections and synthetic data computed from impedance logs is shown for two zones. An upper (steep slope zone contains a moderately continuous, possibly bottom-simulating reflector feature along the corresponding section. This feature may be associated with a lithology boundary near a drill site in addition to, or instead of, a stability boundary of gas hydrates (i.e., gas below and hydrates above. The lower (gentle slope zone has locally cross-cutting reflection patterns that are more likely to be attributed to gas- and hydrate-related physical phenomena than to spatiotemporal changes in lithology. This seismic inversion is informative and useful, making a contribution to enhance the interpretability of the seismic profiles for a potential hydrate recovery.

  20. Computational design of rolling bearings

    Nguyen-Schäfer, Hung

    2016-01-01

    This book comprehensively presents the computational design of rolling bearings dealing with many interdisciplinary difficult working fields. They encompass elastohydrodynamics (EHD), Hertzian contact theory, oil-film thickness in elastohydrodynamic lubrication (EHL), bearing dynamics, tribology of surface textures, fatigue failure mechanisms, fatigue lifetimes of rolling bearings and lubricating greases, Weibull distribution, rotor balancing, and airborne noises (NVH) in the rolling bearings. Furthermore, the readers are provided with hands-on essential formulas based on the up-to-date DIN ISO norms and helpful examples for computational design of rolling bearings. The topics are intended for undergraduate and graduate students in mechanical and material engineering, research scientists, and practicing engineers who want to understand the interactions between these working fields and to know how to design the rolling bearings for automotive industry and many other industries.

  1. Grease lubrication in rolling bearings

    Lugt, Piet M

    2012-01-01

    The definitive book on the science of grease lubrication for roller and needle bearings in industrial and vehicle engineering. Grease Lubrication in Rolling Bearings provides an overview of the existing knowledge on the various aspects of grease lubrication (including lubrication systems) and the state of the art models that exist today. The book reviews the physical and chemical aspects of grease lubrication, primarily directed towards lubrication of rolling bearings. The first part of the book covers grease composition, properties and rheology, including thermal

  2. Auxiliary bearing design and rotor dynamics analysis of blower fan for HTR-10

    Gao Mingshan; Yang Guojun; Xu Yang; Zhao Lei; Yu Suyuan

    2005-01-01

    The electromagnetic bearing instead of ordinary mechanical bearing was chosen to support the rotor in the blower fan system with helium of 10 MW high temperature gas-cooled test reactor (HTR-10), and the auxiliary bearing was applied in the HTR-10 as the backup protector. When the electromagnetic bearing doesn't work suddenly for the power broken, the auxiliary bearing is used to support the falling rotor with high rotating speed. The rotor system will be protected by the auxiliary bearing. The design of auxiliary bearing is the ultimate safeguard for the system. This rotor is vertically mounted to hold the blower fan. The rotor's length is about 1.5 m, its weight is about 240 kg and the rotating speed is about 5400 r/min. Auxiliary bearing design and rotor dynamics analysis are very important for the design of blower fan to make success. The research status of the auxiliary bearing was summarized in the paper. A sort of auxiliary bearing scheme was proposed. MSC.Marc was selected to analyze the vibration mode and the natural frequency of the rotor. The scheme design of auxiliary bearing and analysis result of rotor dynamics offer the important theoretical base for the protector design and control system of electromagnetic bearing of the blower fan. (authors)

  3. African Journals Online (AJOL)

    African Journals OnLine (AJOL) is the world's largest online library of ... and find other information sources and more resources for researchers and journals. ... Potchefstroom Electronic Law Journal/Potchefstroomse Elektroniese Regsblad.

  4. African Journals Online (AJOL)

    African Journals OnLine (AJOL) is the world's largest online library of ... and find other information sources and more resources for researchers and journals. ... Nnamdi Azikiwe University Journal of International Law and Jurisprudence.

  5. African Crop Science Journal

    AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search · USING AJOL ... The African Crop Science Journal, a quarterly publication, publishes original ... interactions, information science, environmental science and soil science.

  6. African Journals Online (AJOL)

    Lwati: A Journal of Contemporary Research. Vol 14, No 3 (2017) ... Journal of Business and Administrative Studies. Vol 6, No 2 (2014) ... Vol 11 (2015): African Journal of Educational Studies in Mathematics and Sciences Vol. 11, 2015. African ...

  7. Ghana Medical Journal: Submissions

    Journal Home > About the Journal > Ghana Medical Journal: Submissions ... Works publishable under this section include original work of suitable standard. ... interest statement of all types of manuscript should be submitted as a separate file.

  8. African Journals Online (AJOL)

    Featured Country: Ghana, Featured Journal: Ghana Medical Journal ... Journal of Business and Administrative Studies; Book Review: Insurance in Ethiopia: ... The Influence of Motivation on Employees' Performance: A Study of Some Selected ...

  9. Nigerian Journal of Ophthalmology

    tulyasys

    Nigerian Journal of Ophthalmology / Jan-Jun 2014 / Vol 1 | Issue 1. I. Nigerian Journal of ... Inquiries about advertising should be sent to Medknow. Publications ... reproduce articles/information from this journal, please ... BUSINESS EDITOR.

  10. Rwandan Journal of Education

    The Rwandan Journal of Education (Rwandan j. educ) is a scholarly, ... The journal is based at the University of Rwanda – College of Education (former Kigali Institute of Education) and it publishes articles that ... AJOL African Journals Online.

  11. African Journals Online (AJOL)

    2013). International Journal of Engineering, Science and Technology. Vol 5, No 3 (2013). International Journal of Engineering, Science and Technology. Vol 30, No 1 (2018). South African Journal of Sports Medicine. Vol 66 (2014). Vulture News.

  12. African Journals Online (AJOL)

    African Journals OnLine (AJOL) is the world's largest online library of ... AJOL works to change this, so that African-origin research output is available to Africans ... South African Medical Journal ... Global Journal of Pure and Applied Sciences.

  13. African Journals Online (AJOL)

    reviewed, African-published scholarly journals. Historically, scholarly information has flowed from North to South and from West to East. It has also been difficult ... Featured Country: Egypt, Arab Rep. Featured Journal: Alexandria Journal of Medicine ...

  14. Hydrostatic and hybrid bearing design

    Rowe, W B

    1983-01-01

    Hydrostatic and Hybrid Bearing Design is a 15-chapter book that focuses on the bearing design and testing. This book first describes the application of hydrostatic bearings, as well as the device pressure, flow, force, power, and temperature. Subsequent chapters discuss the load and flow rate of thrust pads; circuit design, flow control, load, and stiffness; and the basis of the design procedures and selection of tolerances. The specific types of bearings, their design, dynamics, and experimental methods and testing are also shown. This book will be very valuable to students of engineering des

  15. Measurements versus Predictions for a Hybrid (Hydrostatic Plus Hydrodynamic) Thrust Bearing for a Range of Orifice Diameters

    2010-05-01

    Type of Lubrication for a Tilting Pad Thrust Bearing ,” ASME Journal of Lubrication Technology, 96 Ser F (1), pp. 22-27. [9] Gregory, R.S., 1974...1986, “Measurements of Maximum Temperature in Tilting - Pad Thrust Bearings ,” Technical Preprints - Presented at the ASLE 41st Annual Meeting. (ASLE...Safar [7] provides a modified Reynolds number analysis on hydrostatic thrust bearing performance parameters including the effects of tilt . Finally, San

  16. Mechatronics Applied to Fluid Film Bearings: Towards More Efficient Machinery

    Cerda Varela, Alejandro Javier

    the machine is defined as a mechatronic system. This integrated approach comprises the usage of machine elements capable of modifying their characteristics, by using in a combined way mechanical elements, sensors, processing units and actuators. The research project entitled "Mechatronics Applied to Fluid......The current trends regarding turbomachinery design and operation demand for an expansion of the operational boundaries of these mechanical systems, regarding production rate, reliability and adaptability. In order to face the new requirements, it is necessary to migrate towards a new concept, where...... Film Bearings: Towards more Efficient Machinery" was aimed at improving the state of the art regarding the usage of fluid film bearings as "smart" machine elements. Specifically, this project dealt with a tilting pad journal bearing design that features a controllable lubrication system, capable...

  17. African Journals Online (AJOL)

    Continuing Medical Education; Establishing financial markets in Ethiopia: the environmental foundation, challenges and opportunities ... Ethiopian Journal of Education and Sciences; Gender Relations in ... South African Actuarial Journal.

  18. Evaluation of the Thermal Effects in Tilting Pad Bearing

    G. B. Daniel

    2013-01-01

    Full Text Available The analysis of thermal effects is of expressive importance in the context of rotordynamics to evaluate the behavior of hydrodynamic bearings because these effects can influence their dynamic characteristics under specific operational conditions. For this reason, a thermohydrodynamic model is developed in this work, in which the pressure distribution in the oil film and the temperature distribution are calculated together. From the pressure distribution, the velocity distribution field is determined, as well as the viscous dissipation, and consequently, the temperature distribution. The finite volume method is applied to solve the Reynolds equation and the energy equation in the thermohydrodynamic model (THD. The results show that the temperature is higher as the rotational speed increases due to the shear rate of the oil film. The maximum temperature in the bearing occurs in the overloaded pad, near the outlet boundary. The experimental tests were performed in a tilting pad journal bearing operating in a steam turbine to validate the model. The comparison between the experimental and numerical results provides a good correlation. The thermohydrodynamic lubrication developed in this assignment is promising to consistently evaluate the behavior of the tilting pad journal bearing operating in relatively high rotational speeds.

  19. Gas chromatography

    Cram, S.P.; Risby, T.H.; Field, L.R.; Yu, W.L.

    1980-01-01

    In addition to the published literature for the years 1978 - 79, this review of developments in the field of gas chromatography includes earlier articles of particular significance appearing in foreign journals and the patent literature which was not available at the time of the previous review. The articles cited were selected as presenting the most fundamental developments in theory, methodology, and instrumentation. Some applications are cited if they reflect an advance in the state-of-the-art or have particular relevance to new developments. 1149 references are cited

  20. BEARS: Radioactive ion beams at LBNL

    Powell, J.; Guo, F.Q.; Haustein, P.E.

    1998-01-01

    BEARS (Berkeley Experiments with Accelerated Radioactive Species) is an initiative to develop a radioactive ion-beam capability at Lawrence Berkeley National Laboratory. The aim is to produce isotopes at an existing medical cyclotron and to accelerate them at the 88 inch Cyclotron. To overcome the 300-meter physical separation of these two accelerators, a carrier-gas transport system will be used. At the terminus of the capillary, the carrier gas will be separated and the isotopes will be injected into the 88 inch Cyclotron's Electron Cyclotron Resonance (ECR) ion source. The first radioactive beams to be developed will include 20-min 11 C and 70-sec 14 O, produced by (p,n) and (p,α) reactions on low-Z targets. A test program is currently being conducted at the 88 inch Cyclotron to develop the parts of the BEARS system. Preliminary results of these tests lead to projections of initial 11 C beams of up to 2.5 x 10 7 ions/sec and 14 O beams of 3 x 10 5 ions/sec

  1. Distillation of oil-bearing minerals

    1952-05-21

    In the process of distilling oil-bearing minerals such as oil shale which disintegrates during distillation, wherein the subdivided minerals are subjected to a distillation temperature in the form of a highly turbulent dense mass fluidized by an upwardly flowing gasiform medium in a distillation zone and the heat required by the distillation is supplied by burning solid distillation residue with a combustion-supporting gas in the form of a fluidized mass of solids in a separate combustion zone at a temperature substantially higher than the distillation temperature and returning solid combustion residue substantially at the higher temperature to the distillation zone. The steps of starting up the process which consists of maintaining in the distillation and combustion zones dense turbulent fluidized beds of non-disintegrating solids, circulating the non-disintegrating solids between said beds, heating the circulating solids by an auxiliary heat supply until the bed in the distillation zone has reached at least the distillation temperature, thereafter charging fresh oil-bearing minerals to the bed in the distillation zone, continuing the circulation, withdrawing solids which have passed through the combustion zone at a rate adequate to maintain a solids balance, supplying the combustion-supporting gas to the combustion zone to cause the combustion of the residue, and discontinuing the auxilary heating when sufficient heat for the distillation is being generated in the combustion zone.

  2. Superconducting bearings for flywheel applications

    Abrahamsen, Asger Bech

    2001-05-01

    A literature study on the application of superconducting bearings in energy storage flywheel systems. The physics of magnetic levitation and superconductors are presented in the first part of the report, followed by a discussion of the literature found on the applications of superconducting bearings in flywheels. (au)

  3. Superconducting bearings for flywheel applications

    Abrahamsen, A.B.

    2001-01-01

    A literature study on the application of superconducting bearings in energy storage flywheel systems. The physics of magnetic levitation and superconductors are presented in the first part of the report, followed by a discussion of the literature found onthe applications of superconducting bearings...

  4. Space Station alpha joint bearing

    Everman, Michael R.; Jones, P. Alan; Spencer, Porter A.

    1987-01-01

    Perhaps the most critical structural system aboard the Space Station is the Solar Alpha Rotary Joint which helps align the power generation system with the sun. The joint must provide structural support and controlled rotation to the outboard transverse booms as well as power and data transfer across the joint. The Solar Alpha Rotary Joint is composed of two transition sections and an integral, large diameter bearing. Alpha joint bearing design presents a particularly interesting problem because of its large size and need for high reliability, stiffness, and on orbit maintability. The discrete roller bearing developed is a novel refinement to cam follower technology. It offers thermal compensation and ease of on-orbit maintenance that are not found in conventional rolling element bearings. How the bearing design evolved is summarized. Driving requirements are reviewed, alternative concepts assessed, and the selected design is described.

  5. Flywheel Challenge: HTS Magnetic Bearing

    Werfel, F N; Floegel-Delor, U; Riedel, T; Rothfeld, R; Wippich, D; Goebel, B

    2006-01-01

    A 200 mm cylindrical engineering prototype high temperature superconducting (HTS) was designed and fabricated. Measurements show that the 17 kg PM rotor can suspend safely 1000 kg in axial direction and 470 kg radially. The rationale for the bearing performance is to stabilize a 400 kg rotor of a new compact 5 kWh/280 kW flywheel energy storage system (COM - FESS). Measurements of the magnetic bearing force, stiffness and drag-torque are presented indicated the successful targeting a milestone in the HTS bearing technology. The influence of the PM configuration and the YBCO temperature on the bearing performance was experimentally studied, providing high-force or high-stiffness behaviour. The axial stiffness 5 kN/mm at 0.5 mm displacement is the highest value of a HTS bearing we know

  6. Nonlinear dynamics of attractive magnetic bearings

    Hebbale, K. V.; Taylor, D. L.

    1987-01-01

    The nonlinear dynamics of a ferromagnetic shaft suspended by the force of attraction of 1, 2, or 4 independent electromagnets is presented. Each model includes a state variable feedback controller which has been designed using the pole placement method. The constitutive relationships for the magnets are derived analytically from magnetic circuit theory, and the effects of induced eddy currents due to the rotation of the journal are included using Maxwell's field relations. A rotor suspended by four electro-magnets with closed loop feedback is shown to have nine equilibrium points within the bearing clearance space. As the rotor spin speed increases, the system is shown to pass through a Hopf bifurcation (a flutter instability). Using center manifold theory, this bifurcation can be shown to be of the subcritical type, indicating an unstable limit cycle below the critical speed. The bearing is very sensitive to initial conditions, and the equilibrium position is easily upset by transient excitation. The results are confirmed by numerical simulation.

  7. Magnetic bearings for free-piston Stirling engines

    Curwen, P. W.; Fleming, D. P.; Rao, D. K.; Wilson, D. S.

    1992-01-01

    The feasibility and efficacy of applying magnetic bearings to free-piston Stirling-cycle power conversion machinery currently being developed for long-term space missions are assessed. The study was performed for a 50-kWe Reference Stirling Space Power Converter (RSSPC) which currently uses hydrostatic gas bearings to support the reciprocating displacer and power piston assemblies. Active magnetic bearings of the attractive electromagnetic type are feasible for the RSSPC power piston. Magnetic support of the displacer assembly would require unacceptable changes to the design of the current RSSPC. However, magnetic suspension of both displacer and power piston is feasible for a relative-displacer version of the RSSPC. Magnetic suspension of the RSSPC power piston can potentially increase overall efficiency by 0.5 to 1 percent (0.1 to 0.3 efficiency points). Magnetic bearings will also overcome several operational concerns associated with hydrostatic gas bearing systems. These advantages, however, are accompanied by a 5 percent increase in specific mass of the RSSPC.

  8. Thermal conductivity measurements in unsaturated hydrate-bearing sediments

    Dai, Sheng; Cha, Jong-Ho; Rosenbaum, Eilis J.; Zhang, Wu; Seol, Yongkoo

    2015-08-01

    Current database on the thermal properties of hydrate-bearing sediments remains limited and has not been able to capture their consequential changes during gas production where vigorous phase changes occur in this unsaturated system. This study uses the transient plane source (TPS) technique to measure the thermal conductivity of methane hydrate-bearing sediments with various hydrate/water/gas saturations. We propose a simplified method to obtain thermal properties from single-sided TPS signatures. Results reveal that both volume fraction and distribution of the pore constituents govern the thermal conductivity of unsaturated specimens. Thermal conductivity hysteresis is observed due to water redistribution and fabric change caused by hydrate formation and dissociation. Measured thermal conductivity increases evidently when hydrate saturation Sh > 30-40%, shifting upward from the geometric mean model prediction to a Pythagorean mixing model. These observations envisage a significant drop in sediment thermal conductivity when residual hydrate/water saturation falls below ~40%, hindering further gas production.

  9. International Journal of Humanistic Studies: About this journal

    International Journal of Humanistic Studies: About this journal. Journal Home > International Journal of Humanistic Studies: About this journal. Log in or Register to get access to full text downloads.

  10. East and Central African Journal of Surgery: About this journal

    East and Central African Journal of Surgery: About this journal. Journal Home > East and Central African Journal of Surgery: About this journal. Log in or Register to get access to full text downloads.

  11. Ethiopian Journal of Business and Economics (The): About this journal

    Ethiopian Journal of Business and Economics (The): About this journal. Journal Home > Ethiopian Journal of Business and Economics (The): About this journal. Log in or Register to get access to full text downloads.

  12. Zagazig Journal of Occupational Health and Safety: About this journal

    Zagazig Journal of Occupational Health and Safety: About this journal. Journal Home > Zagazig Journal of Occupational Health and Safety: About this journal. Log in or Register to get access to full text downloads.

  13. Journal of Technology and Education in Nigeria: About this journal

    Journal of Technology and Education in Nigeria: About this journal. Journal Home > Journal of Technology and Education in Nigeria: About this journal. Log in or Register to get access to full text downloads.

  14. Tropical Journal of Pharmaceutical Research: About this journal

    Tropical Journal of Pharmaceutical Research: About this journal. Journal Home > Tropical Journal of Pharmaceutical Research: About this journal. Log in or Register to get access to full text downloads.

  15. Nigerian Journal of Pharmaceutical Research: About this journal

    Nigerian Journal of Pharmaceutical Research: About this journal. Journal Home > Nigerian Journal of Pharmaceutical Research: About this journal. Log in or Register to get access to full text downloads.

  16. Journal of Computer Science and Its Application: About this journal

    Journal of Computer Science and Its Application: About this journal. Journal Home > Journal of Computer Science and Its Application: About this journal. Log in or Register to get access to full text downloads.

  17. Nigeria Journal of Pure and Applied Physics: About this journal

    Nigeria Journal of Pure and Applied Physics: About this journal. Journal Home > Nigeria Journal of Pure and Applied Physics: About this journal. Log in or Register to get access to full text downloads.

  18. African Journals Online: Tunisia

    speaking countries. Our web site allows a free full text access to approximately 250 articles published since the year 2000. Other websites related to this journal: http://www.journal-storl.net/ · View Journal | Current Issue | Register This Journal is Open ...

  19. Nigerian Journal of Technology

    AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search · USING AJOL ... Journal Home > Vol 37, No 1 (2018) ... Any paper submitted to the journal should be an original thought-provoking review or appraisal of existing knowledge, ... design and construction or performance evaluation of technological systems.

  20. African Journals Online: Botswana

    Botswana Journal of Economics. The Botswana Journal of Economics is a professional journal established for the dissemination of contemporary economic issues–theoretical, methodological, and policy relevant–in the context of both the immediate environment and the wider international community. View Journal | Current ...