Frequency tuning of single photons from a whispering-gallery mode resonator to MHz-wide transitions

DEFF Research Database (Denmark)

Schunk, G.; Vogl, U.; Sedlmeir, F.

2016-01-01

photons, which is based on parametric down-conversion in a triply resonant whispering-gallery mode resonator, with alkaline transitions [Schunk et al., Optica 2015, 2, 773]. In this paper, we analyse our source in terms of phase matching, available wavelength-tuning mechanisms and applications...

All-polymer photonic sensing platform based on whispering-gallery mode microgoblet lasers

OpenAIRE

Wienhold, T.; Kraemmer, S.; Wondimu, S.F.; Siegle, T.; Bog, U.; Weinzierl, U.; Schmidt, S.; Becker, H.; Kalt, H.; Mappes, T.; Koeber, S.; Koos, C.

2015-01-01

We present an all-polymer photonic sensing platform based on whispering-gallery mode microgoblet lasers integrated into a microfluidic chip. The chip is entirely made from polymers, enabling the use of the devices as low-cost disposables. The microgoblet cavities feature quality factors exceeding 105 and are fabricated from poly(methyl methacrylate) (PMMA) using spin-coating, mask-based optical lithography, wet chemical etching, and thermal reflow. In contrast to silica-based microtoroid reso...

Ultra-high Q terahertz whispering-gallery modes in a silicon resonator

Science.gov (United States)

Vogt, Dominik Walter; Leonhardt, Rainer

2018-05-01

We report on the first experimental demonstration of terahertz (THz) whispering-gallery modes (WGMs) with an ultra-high quality factor of 1.5 × 104 at 0.62 THz. The WGMs are observed in a high resistivity float zone silicon spherical resonator coupled to a sub-wavelength silica waveguide. A detailed analysis of the coherent continuous wave THz spectroscopy measurements combined with a numerical model based on Mie-Debye-Aden-Kerker theory allows us to unambiguously identify the observed higher order radial THz WGMs.

Two-photon excited whispering-gallery mode ultraviolet laser from an individual ZnO microneedle

Science.gov (United States)

Zhu, G. P.; Xu, C. X.; Zhu, J.; Lv, C. G.; Cui, Y. P.

2009-02-01

Wurtzite structural ZnO microneedles with hexagonal cross section were fabricated by vapor-phase transport method and an individual microneedle was employed as a lasing microcavity. Under excitation of a femtosecond pulse laser with 800 nm wavelength, the ultraviolet (UV) laser emission was obtained, which presented narrow linewidth and high Q value. The UV emission, resonant mechanism, and laser mode characteristics were discussed in detail. The results demonstrated that the UV laser originated from the whispering-gallery mode induced by two-photon absorption assisted by Rabi oscillation.

Controlled assembly of organic whispering-gallery-mode microlasers as highly sensitive chemical vapor sensors.

Science.gov (United States)

Gao, Miaomiao; Wei, Cong; Lin, Xianqing; Liu, Yuan; Hu, Fengqin; Zhao, Yong Sheng

2017-03-09

We demonstrate the fabrication of organic high Q active whispering-gallery-mode (WGM) resonators from π-conjugated polymer by a controlled emulsion-solvent-evaporation method, which can simultaneously provide optical gain and act as an effective resonant cavity. By measuring the shift of their lasing modes on exposure to organic vapor, we successfully monitored the slight concentration variation in the chemical gas. These microlaser sensors demonstrated high detection sensitivity and good signal repeatability under continuous chemical gas treatments. The results offer an effective strategy to design miniaturized optical sensors.

Optical sum-frequency generation in a whispering-gallery-mode resonator

International Nuclear Information System (INIS)

Strekalov, Dmitry V; Kowligy, Abijith S; Huang, Yu-Ping; Kumar, Prem

2014-01-01

We demonstrate sum-frequency generation between a telecom wavelength and the Rb D2 line, achieved through natural phase matching in a nonlinear whispering gallery mode resonator. Due to the strong optical field confinement and ultra high Q of the cavity, the process saturates already at sub-mW pump peak power, at least two orders of magnitude lower than in existing waveguide-based devices. The experimental data are in agreement with the nonlinear dynamics and phase matching theory based on spherical geometry. Our experimental and theoretical results point toward a new platform for manipulating the color and quantum states of light waves for applications such as atomic memory based quantum networking and logic operations with optical signals. (paper)

Surface plasmon-enhanced two-photon excited whispering-gallery modes ultraviolet laser from Zno microwire

Directory of Open Access Journals (Sweden)

Yunpeng Wang

2017-11-01

Full Text Available The two-photon excited UV laser with narrow line width and high Q value was obtained. The total internal reflection from the four side surfaces of the quadrilateral-ZnO microwire offered the whispering gallery mode (WGM resonant cavity. The UV emission, resonant mechanism, and laser mode characteristics were discussed in detail for this special type of micro-cavity. In addition, in order to enhance the power of the two-photon excited UV laser, the surface plasmon enhancement by the Au nanoparticles was also performed and explained well by the theory of the localized surface plasmon.

Silica hollow bottle resonators for use as whispering gallery mode based chemical sensors

Science.gov (United States)

Stoian, Razvan-Ionut; Bui, Khoa V.; Rosenberger, A. T.

2015-12-01

A simple three-step method for making silica hollow bottle resonators (HBRs) was developed. This procedure is advantageous because it uses commercially available materials, is cost effective, and is easy to implement. Additionally, the use of these HBRs as whispering gallery mode based chemical sensors is demonstrated by preliminary absorption sensing results in the near infrared (1580-1660 nm) using a trace gas (CH4) in air at atmospheric pressure and a dye (SDA2072) in methanol solution.

Rapid 3D µ-printing of polymer optical whispering-gallery mode resonators.

Science.gov (United States)

Wu, Jushuai; Guo, Xin; Zhang, A Ping; Tam, Hwa-Yaw

2015-11-16

A novel microfabrication method for rapid printing of polymer optical whispering-gallery mode (WGM) resonators is presented. A 3D micro-printing technology based on high-speed optical spatial modulator (SLM) and high-power UV light source is developed to fabricate suspended-disk WGM resonator array using SU-8 photoresist. The optical spectral responses of the fabricated polymer WGM resonators were measured with a biconically tapered optical fiber. Experimental results reveal that the demonstrated method is very flexible and time-saving for rapid fabrication of complex polymer WGM resonators.

Whispering gallery modes in two-photon fluorescence from spherical DCM dye microresonators

Science.gov (United States)

Mamonov, Evgeniy A.; Maydykovskiy, Anton I.; Mitetelo, Nikolai V.; Venkatakrishnarao, Dasari; Chandrasekar, Rajadurai; Murzina, Tatyana V.

2018-03-01

Organic microstructures are well known for their resonator properties, which bring about whispering gallery mode (WGM) excitation. Here we report on experimental evidence of the WGM in the two-photon fluorescence (TPF) of DCM dye microspheres made using the self-assembly method. The WGM excitation accompanying the overall TPF in the spectral range from 530\\div640 nm demonstrated a quality factor of approximately 102 for spheres that were several microns in diameter. The power dependence of the TPF intensity proved the second order nature of the interaction process involved.

Silica hollow bottle resonators for use as whispering gallery mode based chemical sensors

International Nuclear Information System (INIS)

Stoian, Razvan-Ionut; Bui, Khoa V; Rosenberger, A T

2015-01-01

A simple three-step method for making silica hollow bottle resonators (HBRs) was developed. This procedure is advantageous because it uses commercially available materials, is cost effective, and is easy to implement. Additionally, the use of these HBRs as whispering gallery mode based chemical sensors is demonstrated by preliminary absorption sensing results in the near infrared (1580–1660 nm) using a trace gas (CH 4 ) in air at atmospheric pressure and a dye (SDA2072) in methanol solution. (paper)

Hyperparametric effects in a whispering-gallery mode rutile dielectric resonator at liquid helium temperatures

Energy Technology Data Exchange (ETDEWEB)

Nand, Nitin R.; Goryachev, Maxim; Floch, Jean-Michel le; Creedon, Daniel L.; Tobar, Michael E. [ARC Centre for Engineered Quantum Systems, School of Physics, The University of Western Australia, 35 Stirling Highway, Crawley 6009, Western Australia (Australia)

2014-10-07

We report the first observation of low power drive level sensitivity, hyperparametric amplification, and single-mode hyperparametric oscillations in a dielectric rutile whispering-gallery mode resonator at 4.2 K. The latter gives rise to a comb of sidebands at 19.756 GHz. Whereas, most frequency combs in the literature have been observed in optical systems using an ensemble of equally spaced modes in microresonators or fibers, the present work represents generation of a frequency comb using only a single-mode. The experimental observations are explained by an additional 1/2 degree-of-freedom originating from an intrinsic material nonlinearity at optical frequencies, which affects the microwave properties due to the extremely low loss of rutile. Using a model based on lumped circuits, we demonstrate that the resonance between the photonic and material 1/2 degree-of-freedom, is responsible for the hyperparametric energy transfer in the system.

Using Whispering-Gallery-Mode Resonators for Refractometry

Science.gov (United States)

Matsko, Andrey; Savchenkov, Anatoliy; Strekalov, Dmitry; Iltchenko, Vladimir; Maleki, Lute

2010-01-01

A method of determining the refractive and absorptive properties of optically transparent materials involves a combination of theoretical and experimental analysis of electromagnetic responses of whispering-gallery-mode (WGM) resonator disks made of those materials. The method was conceived especially for use in studying transparent photorefractive materials, for which purpose this method affords unprecedented levels of sensitivity and accuracy. The method is expected to be particularly useful for measuring temporally varying refractive and absorptive properties of photorefractive materials at infrared wavelengths. Still more particularly, the method is expected to be useful for measuring drifts in these properties that are so slow that, heretofore, the properties were assumed to be constant. The basic idea of the method is to attempt to infer values of the photorefractive properties of a material by seeking to match (1) theoretical predictions of the spectral responses (or selected features thereof) of a WGM of known dimensions made of the material with (2) the actual spectral responses (or selected features thereof). Spectral features that are useful for this purpose include resonance frequencies, free spectral ranges (differences between resonance frequencies of adjacently numbered modes), and resonance quality factors (Q values). The method has been demonstrated in several experiments, one of which was performed on a WGM resonator made from a disk of LiNbO3 doped with 5 percent of MgO. The free spectral range of the resonator was approximately equal to 3.42 GHz at wavelengths in the vicinity of 780 nm, the smallest full width at half maximum of a mode was approximately equal to 50 MHz, and the thickness of the resonator in the area of mode localization was 30 microns. In the experiment, laser power of 9 mW was coupled into the resonator with an efficiency of 75 percent, and the laser was scanned over a frequency band 9 GHz wide at a nominal wavelength of

Whispering Gallery Mode Based Optical Fiber Sensor for Measuring Concentration of Salt Solution

Directory of Open Access Journals (Sweden)

Chia-Chin Chiang

2013-01-01

Full Text Available An optical fiber solution-concentration sensor based on whispering gallery mode (WGM is proposed in this paper. The WGM solution-concentration sensors were used to measure salt solutions, in which the concentrations ranged from 1% to 25% and the wavelength drifted from the left to the right. The experimental results showed an average sensitivity of approximately 0.372 nm/% and an R2 linearity of 0.8835. The proposed WGM sensors are of low cost, feasible for mass production, and durable for solution-concentration sensing.

Tunable waveguide and cavity in a phononic crystal plate by controlling whispering-gallery modes in hollow pillars

DEFF Research Database (Denmark)

Jin, Yabin; Fernez, Nicolas; Pennec, Yan

2016-01-01

We investigate the properties of a phononic crystal plate with hollow pillars and introduce the existence of whispering-gallery modes (WGMs). We show that by tuning the inner radius of the hollow pillar, these modes can merge inside both Bragg and low frequency band gaps, deserving phononic crystal...... and acoustic metamaterial applications. These modes can be used as narrow pass bands for which the quality factor can be greatly enhanced by the introduction of an additional cylinder between the hollow cylinder and the plate. We discuss some functionalities of these confined WGM in both Bragg and low...

Surface-Enhanced Raman Scattering Using Silica Whispering-Gallery Mode Resonators

Science.gov (United States)

Anderson, Mark S.

2013-01-01

The motivation of this work was to have robust spectroscopic sensors for sensitive detection and chemical analysis of organic and molecular compounds. The solution is to use silica sphere optical resonators to provide surface-enhanced spectroscopic signal. Whispering-gallery mode (WGM) resonators made from silica microspheres were used for surface-enhanced Raman scattering (SERS) without coupling to a plasmonic mechanism. Large Raman signal enhancement is observed by exclusively using 5.08-micron silica spheres with 785-nm laser excitation. The advantage of this non-plasmonic approach is that the active substrate is chemically inert silica, thermally stable, and relatively simple to fabricate. The Raman signal enhancement is broadly applicable to a wide range of molecular functional groups including aliphatic hydrocarbons, siloxanes, and esters. Applications include trace organic analysis, particularly for in situ planetary instruments that require robust sensors with consistent response.

Coupling single NV-centres to high-Q whispering gallery modes of a preselected frequency-matched microresonator

International Nuclear Information System (INIS)

Schietinger, Stefan; Benson, Oliver

2009-01-01

In this paper, we report the controlled coupling of fluorescence from a single NV-centre in a single nanodiamond to the high-Q modes of a preselected microsphere. Microspheres from an ensemble with a finite size distribution can be characterized precisely via white light Mie-scattering. The mode spectrum of individual spheres can be determined with high precision. A sphere with an appropriate spectrum can be selected, and a nanodiamond containing a single NV-centre can be coupled to it. The spectral position of the calculated lowest order whispering gallery modes are found to be in very good agreement with the experimentally observed resonances of the coupled fluorescence from the single NV-re.

Split-disk micro-lasers: Tunable whispering gallery mode cavities

Directory of Open Access Journals (Sweden)

T. Siegle

2017-09-01

Full Text Available Optical micro-cavities of various types have emerged as promising photonic structures, for both the investigation of fundamental science in cavity quantum electrodynamics and simultaneously for various applications, e.g., lasers, filters, or modulators. In either branch a demand for adjustable and tunable photonic devices becomes apparent, which has been mainly based on the modification of the refractive index of the micro-resonators so far. In this paper, we report on a novel type of whispering gallery mode resonator where resonance tuning is achieved by modification of the configuration. This is realized by polymeric split-disks consisting of opposing half-disks with an intermediate air gap. Functionality of the split-disk concept and its figures of merit like low-threshold lasing are demonstrated for laser dye-doped split-disks fabricated by electron beam lithography on Si substrates. Reversible resonance tuning is achieved for split-disks structured onto elastomeric substrates by direct laser writing. The gap width and hence the resonance wavelength can be well-controlled by mechanically stretching the elastomer and exploiting the lateral shrinkage of the substrate. We demonstrate a broad spectral tunability of laser modes by more than three times the free spectral range. These cavities have the potential to form a key element of flexible and tunable photonic circuits based on polymers.

Simulation of whispering-gallery-mode resonance shifts for optical miniature biosensors

Energy Technology Data Exchange (ETDEWEB)

Quan Haiyong [Department of Mechanical and Aerospace Engineering, Rutgers, State University of New Jersey, 98 Brett Road, Piscataway, NJ 08854 (United States); Guo Zhixiong [Department of Mechanical and Aerospace Engineering, Rutgers, State University of New Jersey, 98 Brett Road, Piscataway, NJ 08854 (United States)]. E-mail: guo@jove.rutgers.edu

2005-06-15

Finite element analyses are made of the shifts of resonance frequencies of whispering-gallery-mode (WGM) for a fiber-microsphere coupling miniature sensor. The time-domain Maxwell's equations were adopted to describe the near-field radiation transport and solved by the in-plane TE waves application mode of the FEMLAB. The electromagnetic fields as well as the radiation energy distributions can be easily obtained by the finite element analysis. The resonance intensity spectrum curves in the frequency range from 213 to 220THz were studied under different biosensing conditions. Emphasis was put on the analyses of resonance shift sensitivity influenced by changes of the effective size of the sensor resonator (i.e., microsphere) and/or the refractive index of the medium surrounding the resonator. It is estimated that the WGM biosensor can distinguish molecular size change to the level of 0.1nm and refractive index change in the magnitude of {approx}10{sup -3} even with the use of a general optical spectrum analyzer of one GHz linewidth. Finally, the potential of the WGM miniature biosensor for monitoring peptide growth is investigated and a linear sensor curve is obtained.

High resolution terahertz spectroscopy of a whispering gallery mode bubble resonator using Hilbert analysis.

Science.gov (United States)

Vogt, Dominik Walter; Leonhardt, Rainer

2017-07-10

We report on data processing for continuous wave (CW) terahertz (THz) spectroscopy measurements based on a Hilbert spectral analysis to achieve MHz resolution. As an example we investigate the spectral properties of a whispering gallery mode (WGM) THz bubble resonator at critical coupling. The experimental verification clearly demonstrates the significant advantages in relative frequency resolution and required acquisition time of the proposed method over the traditional data analysis. An effective frequency resolution, only limited by the precision and stability of the laser beat signal, can be achieved without complex extensions to a standard commercially available CW THz spectrometer.

THz Pyro-Optical Detector Based on LiNbO3 Whispering Gallery Mode Microdisc Resonator

Science.gov (United States)

Cosci, Alessandro; Cerminara, Matteo; Nunzi Conti, Gualtiero; Soria, Silvia; Righini, Giancarlo C.; Pelli, Stefano

2017-01-01

This study analyzes the capabilities of a LiNbO3 whispering gallery mode microdisc resonator as a potential bolometer detector in the THz range. The resonator is theoretically characterized in the stationary regime by its thermo-optic and thermal coefficients. Considering a Q-factor of 107, a minimum detectable power of 20 μW was evaluated, three orders of magnitude above its noise equivalent power. This value opens up the feasibility of exploiting LiNbO3 disc resonators as sensitive room-temperature detectors in the THz range. PMID:28134857

Quantification of whispering gallery mode spectrum variability in application to sensing nanobiophotonics

Science.gov (United States)

Saetchnikov, Anton; Skakun, Victor; Saetchnikov, Vladimir; Tcherniavskaia, Elina; Ostendorf, Andreas

2017-10-01

An approach for the automated whispering gallery mode (WGM) signal decomposition and its parameter estimation is discussed. The algorithm is based on the peak picking and can be applied for the preprocessing of the raw signal acquired from the multiplied WGM-based biosensing chips. Quantitative estimations representing physically meaningful parameters of the external disturbing factors on the WGM spectral shape are the output values. Derived parameters can be directly applied to the further deep qualitative and quantitative interpretations of the sensed disturbing factors. The algorithm is tested on both simulated and experimental data taken from the bovine serum albumin biosensing task. The proposed solution is expected to be a useful contribution to the preprocessing phase of the complete data analysis engine and is expected to push the WGM technology toward the real-live sensing nanobiophotonics.

Whispering-gallery-mode resonance sensor for dielectric sensing of drug tablets

International Nuclear Information System (INIS)

Neshat, Mohammad; Chen, Huanyu; Safavi-Naeini, Safieddin; Gigoyan, Suren; Saeedkia, Daryoosh

2010-01-01

We propose, for the first time, the application of whispering gallery mode (WGM) perturbation technique in dielectric analysis of disk shape pharmaceutical tablets. Based on WGM resonance, a low-cost high sensitivity sensor in milllimeter-wave frequency range is presented. A comprehensive sensitivity analysis was performed to show that a change in the order of 10 −4 in the sample permittivity can be detected by the proposed sensor. The results of various experiments carried out on drug tablets are reported to demonstrate the potential multifunctional capabilities of the sensor in moisture sensing, counterfeit drug detection and contamination screening. Analytically, two sample placement configurations, i.e. a tablet placed on top of a dielectric disk resonator and inside a dielectric ring resonator, have been studied to predict the resonance frequency and Q-factor of the combined sample-resonator structure. The accuracy of the analytical model was tested against full-wave simulations and experimental data

Biodetection Technologies for First Responders

Energy Technology Data Exchange (ETDEWEB)

Baird, Cheryl L.; Seiner, Derrick R.; Ozanich, Richard M.; Bartholomew, Rachel A.; Colburn, Heather A.; Straub, Tim M.; Bruckner-Lea, Cindy J.

2012-10-24

In a white powder scenario, there are a large number of field-deployable assays that can be used to determine if the suspicious substance contains biological material and warrants further investigation. This report summarizes commercially available technologies that are considered hand portable and can be used by first responders in the field. This is not meant to be an exhaustive list, nor do the authors endorse any of the technologies described herein. Rather, it is meant to provide useful information about available technologies to help end-users make informed decisions about biodetection technology procurement and use.

Photoluminescence and lasing in whispering gallery mode glass microspherical resonators

Energy Technology Data Exchange (ETDEWEB)

Ristić, D. [Ruđer Bošković Institute, Division of Materials Physics, Laboratory for Molecular Physics, Bijenička c. 54, Zagreb (Croatia); Center of Excellence for Advanced Materials and Sensing Devices, Research unit New Functional Materials, Bijenička c. 54, Zagreb (Croatia); Berneschi, S.; Camerini, M. [IFAC-CNR Istituto di Fisica Applicata, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Farnesi, D.; Pelli, S. [IFAC-CNR Istituto di Fisica Applicata, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Centro Studi e Ricerche ' E. Fermi' , Piazza del Viminale 2, 00184 Roma (Italy); Trono, C. [IFAC-CNR Istituto di Fisica Applicata, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Chiappini, A.; Chiasera, A.; Ferrari, M. [CSMFO Group, Istituto di Fotonica e Nanotecnologie, IFN-CNR, Via alla Cascata 56/C, 38050 Povo-Trento (Italy); Lukowiak, A. [Institute of Low Temperature and Structure Research, PAS, ul. Okolna 2, Wroclaw 50-950 (Poland); Dumeige, Y.; Féron, P. [Laboratoire d' Optronique, (CNRS-UMR 6082-Foton), ENSSAT, 6 rue de Kérampont, 22300 Lannion (France); Righini, G.C. [IFAC-CNR Istituto di Fisica Applicata, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Centro Studi e Ricerche ' E. Fermi' , Piazza del Viminale 2, 00184 Roma (Italy); Soria, S., E-mail: s.soria@ifac.cnr.it [IFAC-CNR Istituto di Fisica Applicata, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Conti, G. Nunzi [IFAC-CNR Istituto di Fisica Applicata, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Centro Studi e Ricerche ' E. Fermi' , Piazza del Viminale 2, 00184 Roma (Italy)

2016-02-15

We report experimental results regarding the development of Er{sup 3+}-doped glass microspherical cavities for the fabrication of compact sources at 1.55 μm. We investigate several different approaches in order to fabricate the microspheres including direct melting of Er{sup 3+}-doped glass powders, synthesis of Er{sup 3+}-doped monolithic microspheres by drawing Er{sup 3+}-doped glass, and coating of silica microspheres with an Er{sup 3+}-doped sol–gel layer. Details of the different fabrication processes are presented together with the photoluminescence characterization in free space configuration of the microspheres and of the glass precursor. We have analyzed the photoluminescence spectra of the whispering gallery modes of the microspheres excited using evanescent coupling and we demonstrate tunable laser action in a wide range of wavelengths around 1.55 μm. As much as 90 μW of laser output power was measured in Er{sup 3+}-doped glass microspheres. - Highlights: • Different approaches in microsphere fabrication and various types of post-processing. • Trimming of photorefractive glass microsphere lasers with UV light. • Peak power record of 90 μW by pumping at 1480 nm.

Detecting single viruses and nanoparticles using whispering gallery microlasers.

Science.gov (United States)

He, Lina; Ozdemir, Sahin Kaya; Zhu, Jiangang; Kim, Woosung; Yang, Lan

2011-06-26

There is a strong demand for portable systems that can detect and characterize individual pathogens and other nanoscale objects without the use of labels, for applications in human health, homeland security, environmental monitoring and diagnostics. However, most nanoscale objects of interest have low polarizabilities due to their small size and low refractive index contrast with the surrounding medium. This leads to weak light-matter interactions, and thus makes the label-free detection of single nanoparticles very difficult. Micro- and nano-photonic devices have emerged as highly sensitive platforms for such applications, because the combination of high quality factor Q and small mode volume V leads to significantly enhanced light-matter interactions. For example, whispering gallery mode microresonators have been used to detect and characterize single influenza virions and polystyrene nanoparticles with a radius of 30 nm (ref. 12) by measuring in the transmission spectrum either the resonance shift or mode splitting induced by the nanoscale objects. Increasing Q leads to a narrower resonance linewidth, which makes it possible to resolve smaller changes in the transmission spectrum, and thus leads to improved performance. Here, we report a whispering gallery mode microlaser-based real-time and label-free detection method that can detect individual 15-nm-radius polystyrene nanoparticles, 10-nm gold nanoparticles and influenza A virions in air, and 30 nm polystyrene nanoparticles in water. Our approach relies on measuring changes in the beat note that is produced when an ultra-narrow emission line from a whispering gallery mode microlaser is split into two modes by a nanoscale object, and these two modes then interfere. The ultimate detection limit is set by the laser linewidth, which can be made much narrower than the resonance linewidth of any passive resonator. This means that microlaser sensors have the potential to detect objects that are too small to be

Cavity QED experiments with a whispering-gallery-mode bottle resonator

International Nuclear Information System (INIS)

O'Shea, D.

2013-01-01

The interaction of a two-level atom with a single mode of the quantized electromagnetic field constitutes one of the most fundamental systems investigated in quantum optics. We have pursued such an investigation where rubidium atoms are strongly coupled to the modes of a whispering-gallery-mode (WGM) resonator that is itself interfaced with an optical fiber. In order to facilitate studies of this atom-light interaction, an experimental apparatus was constructed around a novel type of WGM resonator developed in our group. The spectral and spatial mode structure of this resonator yield an intriguing atom-light response arising principally from the existence of two frequency-degenerate modes. This thesis reports on high resolution experiments studying the transmission and reflection spectra of modes with a high quality factor (Q=10 7 -10 8 ) in our WGM resonator. Light is coupled into and out of WGMs by frustrated total internal reflection using an optical nanofiber. The atom-light interaction is facilitated by an atomic fountain that delivers a cloud of atoms to the location of the resonator. At random moments, single-atoms are clearly observed transiting the evanescent field of the resonator modes with a transit time of a few microseconds. A high-speed experimental control system was developed to firstly detect the coupling of individual atoms to the resonator and secondly to perform time-resolved spectroscopy on the strongly coupled atom-resonator system. Spectral measurements clearly resolve an atom-induced change in the resonant transmission of the coupled system (65% absolute change) that is much larger than predicted in the standard Jaynes-Cummings model (25% absolute change) and that has thus far not been observed. To gain further insight, we experimentally explored the properties of the interaction and performed supporting simulations. Spectroscopy was performed on the atom-resonator system using two nanofibers to in- and out-couple light for probing

Influence of the whispering-gallery mode resonators shape on its inertial movement sensitivity

Science.gov (United States)

Filatov, Yuri V.; Kukaev, Alexander S.; Shalymov, Egor V.; Venediktov, Vladimir Yu.

2018-01-01

The optical whispering-gallery mode (WGM) resonators are axially symmetrical resonators with smooth edges, supporting the existence of the WGMs by the total internal reflection on the surface of the resonator. As of today, various types of such resonators have been developed, namely the ball shaped, tor shaped, bottle shaped, disk shaped, etc. The movement of WGM resonators in inertial space causes the changes in their shape. The result is a spectral shift of the WGMs. Optical methods allow to register this shift with high precision. It can be used in particular for the measurement of angular velocities in inertial orientation and navigation systems. However, different types of resonators react to the movement in different manners. In addition, their sensitivity to movement can be changed when changing the geometric parameters of these resonators. The work is devoted to investigation of these aspects.

Multi-layer hierarchical array fabricated with diatom frustules for highly sensitive bio-detection applications

International Nuclear Information System (INIS)

Li, Aobo; Cai, Jun; Pan, Junfeng; Wang, Yu; Yue, Yue; Zhang, Deyuan

2014-01-01

Diatoms have delicate porous structures which are very beneficial in improving the absorbing ability in the bio-detection field. In this study, multi-layered hierarchical arrays were fabricated by packing Nitzschia soratensis (N. soratensis) frustules into Cosinodiscus argus (C. argus) frustules to achieve advanced sensitivity in bio-detection chips. Photolithographic patterning was used to obtain N. soratensis frustule arrays, and the floating behavior of C. argus frustules was employed to control their postures for packing N. soratensis frustule array spots. The morphology of the multi-layer C. argus–N. soratensis package array was investigated by scanning electron microscopy, demonstrating that the overall and sub-structures of the diatom frustules were retained. The signal enhancing effect of multi-layer C. argus–N. soratensis packages was demonstrated by fluorescent antibody test results. The mechanism of the enhancement was also analyzed, indicating that both complex hierarchical frustule structures and optimized posture of C. argus frustules were important for improving bio-detection sensitivities. The technique for fabricating multi-layer diatom frustules arrays is also useful for making multi-functional biochips and controllable drug delivery systems. (paper)

Integrated optics nano-opto-fluidic sensor based on whispering gallery modes for picoliter volume refractometry

International Nuclear Information System (INIS)

Gilardi, Giovanni; Beccherelli, Romeo

2013-01-01

We propose and numerically investigate an integrated optics refractometric nano-opto-fluidic sensor based on whispering gallery modes in sapphire microspheres. A measurand fluid is injected in a micromachined reservoir defined in between the microsphere and an optical waveguide. The wavelength shift due to changes in the refractive index of the measurand fluid are studied for a set of different configurations by the finite element method and a high sensitivity versus fluid volume is found. The proposed device can be tailored to work with a minimum fluid volume of 1 pl and a sensitivity up of 2000 nm/(RIU·nl). We introduce a figure of merit which quantifies the amplifying effect on the sensitivity of high quality factor resonators and allows us to compare different devices. (paper)

Optothermal transport behavior in whispering gallery mode optical cavities

Energy Technology Data Exchange (ETDEWEB)

Soltani, Soheil [Ming Hsieh Department of Electrical Engineering-Electrophysics, University of Southern California, Los Angeles, California 90089 (United States); Armani, Andrea M., E-mail: armani@usc.edu [Ming Hsieh Department of Electrical Engineering-Electrophysics, University of Southern California, Los Angeles, California 90089 (United States); Mork Family Department of Chemical Engineering and Materials Science, University of Southern California, Los Angeles, California 90089 (United States)

2014-08-04

Over the past century, whispering gallery mode optical cavities have enabled numerous advances in science and engineering, such as discoveries in quantum mechanics and non-linear optics, as well as the development of optical gyroscopes and add drop filters. One reason for their widespread appeal is their ability to confine light for long periods of time, resulting in high circulating intensities. However, when sufficiently large amounts of optical power are coupled into these cavities, they begin to experience optothermal or photothermal behavior, in which the optical energy is converted into heat. Above the optothermal threshold, the resonance behavior is no longer solely defined by electromagnetics. Previous work has primarily focused on the role of the optothermal coefficient of the material in this instability. However, the physics of this optothermal behavior is significantly more complex. In the present work, we develop a predictive theory based on a generalizable analytical expression in combination with a geometry-specific COMSOL Multiphysics finite element method model. The simulation couples the optical and thermal physics components, accounting for geometry variations as well as the temporal and spatial profile of the optical field. To experimentally verify our theoretical model, the optothermal thresholds of a series of silica toroidal resonant cavities are characterized at different wavelengths (visible through near-infrared) and using different device geometries. The silica toroid offers a particularly rigorous case study for the developed optothermal model because of its complex geometrical structure which provides multiple thermal transport paths.

Image Gallery

Science.gov (United States)

... R S T U V W X Y Z Image Gallery Share: The Image Gallery contains high-quality digital photographs available from ... Select a category below to view additional thumbnail images. Images are available for direct download in 2 ...

Real-Time Detection of Staphylococcus Aureus Using Whispering Gallery Mode Optical Microdisks

Directory of Open Access Journals (Sweden)

Hala Ghali

2016-05-01

Full Text Available Whispering Gallery Mode (WGM microresonators have recently been studied as a means to achieve real-time label-free detection of biological targets such as virus particles, specific DNA sequences, or proteins. Due to their high quality (Q factors, WGM resonators can be highly sensitive. A biosensor also needs to be selective, requiring proper functionalization of its surface with the appropriate ligand that will attach the biomolecule of interest. In this paper, WGM microdisks are used as biosensors for detection of Staphylococcus aureus. The microdisks are functionalized with LysK, a phage protein specific for staphylococci at the genus level. A binding event on the surface shifts the resonance peak of the microdisk resonator towards longer wavelengths. This reactive shift can be used to estimate the surface density of bacteria that bind to the surface of the resonator. The limit of detection of a microdisk with a Q-factor around 104 is on the order of 5 pg/mL, corresponding to 20 cells. No binding of Escherichia coli to the resonators is seen, supporting the specificity of the functionalization scheme.

Electrically tunable whispering gallery mode microresonator based on a grapefruit-microstructured optical fiber infiltrated with nematic liquid crystals.

Science.gov (United States)

Yang, Chengkun; Zhang, Hao; Liu, Bo; Lin, Shiwei; Li, Yuetao; Liu, Haifeng

2017-08-01

An electrically tunable whispering gallery mode (WGM) microresonator based on an HF-etched microstructured optical fiber (MOF) infiltrated with nematic liquid crystals (NLCs) is proposed and experimentally demonstrated. Experimental results indicate that as the peak-to-peak voltage of the applied AC electric field increases from 160 to 220 V, WGM resonance peaks gradually move toward a shorter wavelength region by 0.527 nm with a wavelength sensitivity up to 0.01  nm/V for a TM1691 mode, and the Q-factor for each WGM resonance peak rapidly decreases with the increment of applied electric voltage. The proposed electrically controlled WGM tuning scheme shows a linear resonance wavelength shift with good spectral reversibility, which makes it a promising candidate to serve as an integrated functional photonic device in practical use and in related fundamental scientific studies.

Touchable Computing: Computing-Inspired Bio-Detection.

Science.gov (United States)

Chen, Yifan; Shi, Shaolong; Yao, Xin; Nakano, Tadashi

2017-12-01

We propose a new computing-inspired bio-detection framework called touchable computing (TouchComp). Under the rubric of TouchComp, the best solution is the cancer to be detected, the parameter space is the tissue region at high risk of malignancy, and the agents are the nanorobots loaded with contrast medium molecules for tracking purpose. Subsequently, the cancer detection procedure (CDP) can be interpreted from the computational optimization perspective: a population of externally steerable agents (i.e., nanorobots) locate the optimal solution (i.e., cancer) by moving through the parameter space (i.e., tissue under screening), whose landscape (i.e., a prescribed feature of tissue environment) may be altered by these agents but the location of the best solution remains unchanged. One can then infer the landscape by observing the movement of agents by applying the "seeing-is-sensing" principle. The term "touchable" emphasizes the framework's similarity to controlling by touching the screen with a finger, where the external field for controlling and tracking acts as the finger. Given this analogy, we aim to answer the following profound question: can we look to the fertile field of computational optimization algorithms for solutions to achieve effective cancer detection that are fast, accurate, and robust? Along this line of thought, we consider the classical particle swarm optimization (PSO) as an example and propose the PSO-inspired CDP, which differs from the standard PSO by taking into account realistic in vivo propagation and controlling of nanorobots. Finally, we present comprehensive numerical examples to demonstrate the effectiveness of the PSO-inspired CDP for different blood flow velocity profiles caused by tumor-induced angiogenesis. The proposed TouchComp bio-detection framework may be regarded as one form of natural computing that employs natural materials to compute.

Light-controlled microwave whispering-gallery-mode quasi-optical resonators at 50W LED array illumination

Directory of Open Access Journals (Sweden)

V. B. Yurchenko

2015-08-01

Full Text Available We present experimental observations of light-controlled resonance effects in microwave whispering-gallery-mode quasi-optical dielectric-semiconductor disk resonators in the frequency band of 5 GHz to 20 GHz arising due to illumination from a light emitting diode (LED of 50W power range. We obtain huge enhancement of photo-sensitivity (growing with the resonator Q-factor that makes light-microwave interaction observable with an ordinary light (no laser at conventional brightness (like an office lighting in quasi-optical microwave structures at rather long (centimeter-scale wavelength. We also demonstrate non-conventional photo-response of Fano resonances when the light suppresses one group of resonances and enhances another group. The effects could be used for the optical control and quasi-optical switching of microwave propagation through either one or another frequency channel.

Giant thermo-optical relaxation oscillations in millimeter-size whispering gallery mode disk resonators.

Science.gov (United States)

Diallo, Souleymane; Lin, Guoping; Chembo, Yanne K

2015-08-15

In this Letter, we show that giant thermo-optical oscillations can be triggered in millimeter (mm)-size whispering gallery mode (WGM) disk resonators when they are pumped by a resonant continuous-wave laser. Our resonator is an ultrahigh-Q barium fluoride cavity that features a positive thermo-optic coefficient and a negative thermo-elastic coefficient. We demonstrate for the first time, to our knowledge, that the complex interplay between these two thermic coefficients and the intrinsic Kerr nonlinearity yields very sharp slow-fast relaxation oscillations with a slow timescale that can be exceptionally large, typically of the order of 1 s. We use a time-domain model to gain understanding into this instability, and we find that both the experimental and theoretical results are in excellent agreement. The understanding of these thermal effects is an essential requirement for every WGM-related application and our study demonstrates that even in the case of mm-size resonators, such effects can still be accurately analyzed using nonlinear time-domain models.

Strain tuneable whispering gallery mode resonators in the estimation of the elasto-optic parameters of soft materials

Science.gov (United States)

Pissadakis, Stavros; Milenko, Karolina; Aluculesei, Alina; Fytas, George

2016-04-01

In this manuscript we present the fabrication and characterization of a novel, polymer whispering gallery modes (WGMs) spherical micro-resonator, formed around the waist of an optical fiber taper. Fiber taper with well attached spheroid works as a cord, fixed on two ends enabling strain application to the resonator body. Controllable elastic elongation of the encapsulated fiber taper causes a change in the shape of the spheroid, which modifies the diameter and directional refractive index of the cavity. These changes influence the wavelength position of the WGMs resonances with a linear blue shift up to 0.6 nm, with corresponding strains up to 700Μɛ. The strain induced WGMs shift with respect to resonator diameter and annealing process is presented and analyzed.

Whispering Gallery Mode Resonances from Ge Micro-Disks on Suspended Beams

Directory of Open Access Journals (Sweden)

Abdelrahman Zaher Al-Attili

2015-05-01

Full Text Available Ge is considered to be one of the most promising materials for realizing full monolithic integration of a light source on a silicon (Si photonic chip. Tensile-strain is required to convert Ge into an optical gain material and to reduce the pumping required for population inversion. Several methods of strain application to Ge are proposed in literature, of which the use of free-standing beams fabricated by micro-electro-mechanical systems (MEMS processes are capable of delivering very high strain values. However, it is challenging to make an optical cavity within free-standing Ge beams, and here, we demonstrate the fabrication of a simple cavity while imposing tensile strain by suspension using Ge-On-Insulator (GOI wafers. Ge micro-disks are made on top of suspended SiO$_{2}$ beams by partially removing the supporting Si substrate. According to Raman spectroscopy, a slight tensile strain was applied to the Ge disks through the bending of the SiO2 beams. Whispering-Gallery-Mode (WGM resonances were observed from a disk with a diameter of 3um, consistent with the finite-domain time-difference simulations. The quality (Q factor was 192, and upon increasing the pumping power, the Q-factor was degraded due to the red-shift of Ge direct-gap absorption edge caused by heating.

The Detection of Helicobacter hepaticus Using Whispering-Gallery Mode Microcavity Optical Sensors

Directory of Open Access Journals (Sweden)

Mark E. Anderson

2015-08-01

Full Text Available Current bacterial detection techniques are relatively slow, require bulky instrumentation, and usually require some form of specialized training. The gold standard for bacterial detection is culture testing, which can take several days to receive a viable result. Therefore, simpler detection techniques that are both fast and sensitive could greatly improve bacterial detection and identification. Here, we present a new method for the detection of the bacteria Helicobacter hepaticus using whispering-gallery mode (WGM optical microcavity-based sensors. Due to minimal reflection losses and low material adsorption, WGM-based sensors have ultra-high quality factors, resulting in high-sensitivity sensor devices. In this study, we have shown that bacteria can be non-specifically detected using WGM optical microcavity-based sensors. The minimum detection for the device was 1 × 104 cells/mL, and the minimum time of detection was found to be 750 s. Given that a cell density as low as 1 × 103 cells/mL for Helicobacter hepaticus can cause infection, the limit of detection shown here would be useful for most levels where Helicobacter hepaticus is biologically relevant. This study suggests a new approach for H. hepaticus detection using label-free optical sensors that is faster than, and potentially as sensitive as, standard techniques.

Formation of whispering gallery modes by scattering of an electromagnetic plane wave by two cylinders

Energy Technology Data Exchange (ETDEWEB)

Abramov, Arnold, E-mail: qulaser@gmail.com [Kuang-Chi Institute of Advanced Technology, Shenzhen, 518057 (China); Kostikov, Alexander [Donbass State Engineering Academy, 84303, Kramatorsk, Donetsk (Ukraine)

2017-03-26

We report the effect of scattering of electromagnetic plane waves by two cylinders on whispering gallery mode (WGM) formation in a cylinder. WGM can occur because of the presence of additional cylinder scatterers at specific location, while WGMs can only form in a single cylinder for specific cylinder radius and/or wavelength values, the matching accuracy required would be much greater than that required in our model for the additional cylinders locations. Analysis of the general solution to the problem showed that the effect can be explained by the interference of waves scattered by additional cylinders and incident on the main cylinder. - Highlights: • We consider scattering of electromagnetic plane waves by two cylinders. • WGMs occur because of the presence of additional cylinder at specific location. • The accuracy for the locations is much less than required for specific values of single cylinder. • The interference of waves scattered by additional cylinders and incident on the main is responsible for the effect.

Biodetection Technologies for First Responders: 2014 Edition

Energy Technology Data Exchange (ETDEWEB)

Ozanich, Richard M.; Baird, Cheryl L.; Bartholomew, Rachel A.; Colburn, Heather A.; Straub, Tim M.; Bruckner-Lea, Cindy J.

2014-03-28

This report summarizes commercially-available, hand-portable technologies that can be used by first responders in the field. This is not meant to be an exhaustive list, nor an endorsement of any technology described herein. Rather, this report is meant to provide useful information about available technologies to help end-users make informed decisions about biodetection technology procurement and use. Information listed in this report is primarily vendor-provided; however, where possible it has been supplemented with additional information obtained from publications, reports, and websites. Manufacturers were given the chance to review summaries of their technologies from August through November 2013 to verify the accuracy of technical specifications, available references, and pricing.

Comparison of various excitation and detection schemes for dye-doped polymeric whispering gallery mode micro-lasers.

Science.gov (United States)

Siegle, Tobias; Kellerer, Jonas; Bonenberger, Marielle; Krämmer, Sarah; Klusmann, Carolin; Müller, Marius; Kalt, Heinz

2018-02-05

We compare different excitation and collection configurations based on free-space optics and evanescently coupled tapered fibers for both lasing and fluorescence emission from dye-doped doped polymeric whispering gallery mode (WGM) micro-disk lasers. The focus of the comparison is on the lasing threshold and efficiency of light collection. With the aid of optical fibers, we localize the pump energy to the cavity-mode volume and reduce the necessary pump energy to achieve lasing by two orders of magnitude. When using fibers for detection, the collection efficiency is enhanced by four orders of magnitude compared to a free-space read-out perpendicular to the resonator plane. By enhancing the collection efficiency we are able to record a pronounced modulation of the dye fluorescence under continuous wave (cw) pumping conditions evoked by coupling to the WGMs. Alternatively to fibers as a collection tool, we present a read-out technique based on the detection of in-plane radiated light. We show that this method is especially beneficial in an aqueous environment as well as for size-reduced micro-lasers where radiation is strongly pronounced. Furthermore, we show that this technique allows for the assignment of transverse electric (TE) and transverse magnetic (TM) polarization to the observed fundamental modes in a water environment by performing polarization-dependent photoluminescence (PL) spectroscopy. We emphasize the importance of the polarization determination for sensing applications and verify expected differences in the bulk refractive index sensitivity for TE and TM WGMs experimentally.

Whispering gallery mode resonators for frequency metrology applications

Science.gov (United States)

Baumgartel, Lukas

This dissertation describes an investigation into the use of whispering gallery mode (WGM) resonators for applications towards frequency reference and metrology. Laser stabilization and the measurement of optical frequencies have enabled myriad technologies of both academic and commercial interest. A technology which seems to span both motivations is optical atomic clocks. These devices are virtually unimaginable without the ultra stable lasers plus frequency measurement and down-conversion afforded by Fabry Perot (FP) cavities and model-locked laser combs, respectively. However, WGM resonators can potentially perform both of these tasks while having the distinct advantages of compactness and simplicity. This work represents progress towards understanding and mitigating the performance limitations of WGM cavities for such applications. A system for laser frequency stabilization to a the cavity via the Pound-Drever-Hall (PDH) method is described. While the laser lock itself is found to perform at the level of several parts in 1015, a variety of fundamental and technical mechanisms destabilize the WGM frequency itself. Owing to the relatively large thermal expansion coefficients in optical crystals, environmental temperature drifts set the stability limit at time scales greater than the thermal relaxation time of the crystal. Uncompensated, these drifts pull WGM frequencies about 3 orders of magnitude more than they would in an FP cavity. Thus, two temperature compensation schemes are developed. An active scheme measures and stabilizes the mode volume temperature to the level of several nK, reducing the effective temperature coefficient of the resonator to 1.7x10-7 K-1; simulations suggest that the value could eventually be as low as 3.5x10-8 K-1, on par with the aforementioned FP cavities. A second, passive scheme is also described, which employs a heterogeneous resonator structure that capitalizes on the thermo-mechanical properties of one material and the optical

Mathematical Model for Electric Field Sensor Based on Whispering Gallery Modes Using Navier’s Equation for Linear Elasticity

Directory of Open Access Journals (Sweden)

Amir R. Ali

2017-01-01

Full Text Available This paper presents and verifies the mathematical model of an electric field senor based on the whispering gallery mode (WGM. The sensing element is a dielectric microsphere, where the light is used to tune the optical modes of the microsphere. The light undergoes total internal reflection along the circumference of the sphere; then it experiences optical resonance. The WGM are monitored as sharp dips on the transmission spectrum. These modes are very sensitive to morphology changes of the sphere, such that, for every minute change in the sphere’s morphology, a shift in the transmission spectrum will happen and that is known as WGM shifts. Due to the electrostriction effect, the applied electric field will induce forces acting on the surface of the dielectric sphere. In turn, these forces will deform the sphere causing shifts in its WGM spectrum. The applied electric field can be obtained by calculating these shifts. Navier’s equation for linear elasticity is used to model the deformation of the sphere to find the WGM shift. The finite element numerical studies are performed to verify the introduced model and to study the behavior of the sensor at different values of microspheres’ Young’s modulus and dielectric constant. Furthermore, the sensitivity and resolution of the developed WGM electric filed sensor model will be presented in this paper.

Visual events and the friendly eye: modes of educating vision in new educational settings in Danish art galleries

DEFF Research Database (Denmark)

Illeris, Helene

2009-01-01

  New, experimental educational settings such as ‘art laboratories', ‘digital workshops' and ‘theme-based tours' are important to the processes of change towards more inclusive practices, which have been initiated in many Danish art galleries. While traditional gallery education was constructed...... as visual events, and it discusses how ‘the desiring eye' of some constructivist approaches, along with traditional practices of looking, have contributed to the formation of the modern, autonomous individual. The second part of the article analyses two cases from Danish art galleries and, inspired by Mieke...... in order to stimulate the ‘disciplined eye' or the ‘aesthetic eye' of the visitors, this article aims to discuss the practices of looking encouraged by contemporary and experimental educational projects. The first part of the article develops a theoretical perspective on educational settings conceived...

Biochemical component identification by plasmonic improved whispering gallery mode optical resonance based sensor

Science.gov (United States)

Saetchnikov, Vladimir A.; Tcherniavskaia, Elina A.; Saetchnikov, Anton V.; Schweiger, Gustav; Ostendorf, Andreas

2014-05-01

Experimental data on detection and identification of variety of biochemical agents, such as proteins, microelements, antibiotic of different generation etc. in both single and multi component solutions under varied in wide range concentration analyzed on the light scattering parameters of whispering gallery mode optical resonance based sensor are represented. Multiplexing on parameters and components has been realized using developed fluidic sensor cell with fixed in adhesive layer dielectric microspheres and data processing. Biochemical component identification has been performed by developed network analysis techniques. Developed approach is demonstrated to be applicable both for single agent and for multi component biochemical analysis. Novel technique based on optical resonance on microring structures, plasmon resonance and identification tools has been developed. To improve a sensitivity of microring structures microspheres fixed by adhesive had been treated previously by gold nanoparticle solution. Another technique used thin film gold layers deposited on the substrate below adhesive. Both biomolecule and nanoparticle injections caused considerable changes of optical resonance spectra. Plasmonic gold layers under optimized thickness also improve parameters of optical resonance spectra. Biochemical component identification has been also performed by developed network analysis techniques both for single and for multi component solution. So advantages of plasmon enhancing optical microcavity resonance with multiparameter identification tools is used for development of a new platform for ultra sensitive label-free biomedical sensor.

Landslide Caused Damages in a Gallery

Science.gov (United States)

Poisel, R.; Mair am Tinkhof, K.; Preh, A.

2016-06-01

On October 5th, 2010, cracks were found in a gallery 1.8 m high and 1.4 m wide. The gallery is 100 years old, runs parallel to a valley flank and was excavated in a tectonically strongly stressed, weathered and slightly dipping sandwich of clayey shales, sandstones and marls. The cracks in the roof as well as in the invert ran parallel to the axis of the gallery. Monitoring showed that crack widths were increasing 1.5 mm per year, sidewall distances were increasing 3.5 mm per year, whereas the height of the gallery was decreasing 2.5 mm per year. After eliminating several possible causes of cracking, a landslide producing the damages had to be taken into consideration. Monitoring of the valley flank surface as well as inclinometer readings revealed that a landslide was occurring, loading the gallery lining. Most probably the landslide had been reactivated by excessive rainfall in 2009 as well as by works for the renewal of a weir in the valley bottom. As stabilization of the slope was not an option for several reasons, it was decided to replace the gallery by a new one deeper inside the slope, which will be ready for operation in 2017. Thus the old gallery has to be kept in operation till then and it was decided to reinforce the old gallery by a heavily reinforced shotcrete lining 10 cm thick. As slope displacements went on, cracks in the shotcrete lining developed with a completely different pattern: in the section where the gallery lies completely in the landslide shear zone no cracks formed until now due to heavy reinforcement, whereas in the transition sections stable ground-landslide and landslide-stable ground diagonal tension cracks in the roof due to shear by the landslide developed. Numerical models showed that cracking and spalling of the shotcrete lining would occur only after some centimetres of additional displacements of the slope, which hopefully will not occur before 2017.

Visual events and the friendly eye: modes of educating vision in new educational settings in Danish art galleries

Directory of Open Access Journals (Sweden)

Helene Illeris

2015-04-01

Full Text Available New, experimental educational settings such as ‘art laboratories’, ‘digital workshops’ and ‘theme-based tours’ are important to the processes of change towards more inclusive practices, which have been initiated in many Danish art galleries. While traditional gallery education was constructed in order to stimulate the ‘disciplined eye’ or the ‘aesthetic eye’ of the visitors, this article aims to discuss the practices of looking encouraged by contemporary and experimental educational projects. The first part of the article develops a theoretical perspective on educational settings conceived as visual events, and it discusses how ‘the desiring eye’ of some constructivist approaches, along with traditional practices of looking, have contributed to the formation of the modern, autonomous individual. The second part of the article analyses two cases from Danish art galleries and, inspired by Mieke Bal, proposes the ‘friendly eye’ as a possible dialogical and collective practice of looking that can be stimulated in educational settings.

Optofluidic plasmonic onchip nanosensor array for biodetection

Science.gov (United States)

Huang, Min

Surface plasmon resonance (SPR) sensing has been demonstrated in the past decade to be the gold standard technique for biochemical interaction analysis, and plays an important role in drug discovery and biomedical research. The technique circumvents the need of fluorescence/radioactive tagging or enzymatic detection, enables ultrasensitive remote sensing, and quantitatively monitors bio-interaction in real time. Although SPR has these attractive features that can satisfy most research/clinic requirements, there still exist problems that limit its applications. First, the reflection geometry of the prism coupling scheme adds limitations for high throughput screening application. Additionally, SPR instrumentations are bulky and not suitable for point-of-care settings. Moreover, the SPR sensor is embedded in conventional micro-fluidic cells, in which the sensor performance is limited by inefficient analyte transport. Suspended plasmonic nanohole array (PNA) offers an opportunity to overcome these limitations. A collinear excitation/collection coupling scheme combined with the small footprint of PNA provides unique platform for multiplexing and system minimization. The suspended nanohole structure also offers a unique configuration to integrate nano-photonics with nano-fluidics. This thesis focuses on developing a lab-on-a-chip PNA platform for point-of-care bio-detection. To achieve this, we first demonstrate that the figure-of-merit of our PNA sensor surpasses that of the prism coupled SPR. We also show that the ultrasensitive label-free PNA sensor is able to directly detect intact viruses from biological media at clinically relevant concentrations with little sample preparation. We then present a plasmonic microarray with over one million PNA sensors on a microscope slide for high throughput screening applications. A dual-color filter imaging method is introduced to increase the accuracy, reliability, and signal-to-noise ratio in a highly multiplexed manner. Finally

Advertising identities: virtual galleries as places of identity

Directory of Open Access Journals (Sweden)

Alexandra Zontea

2010-10-01

Full Text Available This paper is focused on the public presentation of self through virtual art galleries, singling out the field of photography. Photography has always been disputed as being part of the highbrow arts because of its popular character. Today, anyone who owes a photo camera can experience photography as art, without a rigorous training. Everybody is able to expose the photos freely to a large number of people, on the Internet. Consequently, the Internet opens up a virtual space, in which photo artists and amateurs can promote their works and exhibit them in a personal online gallery, which represents their place in the virtual vastness. Therefore, my research approaches the matter of the virtual gallery as an identitary place, being focused on finding out why artists choose to exhibit in virtual galleries. I asked myself what are the new functions of the virtual art galleries?Are they understood as online markers that distinguish the owners in these virtual environments? In other words, are these personal galleries a way of expressing online identities?

Upconverting fluorescent nanoparticles for biodetection and photoactivation

Science.gov (United States)

Huang, Kai; Li, WenKai; Jayakumar, Muthu Kumara Gnanasammandhan; Zhang, Yong

2013-03-01

Fluorophores including fluorescent dyes/proteins and quantum dots (QDs) are used for fluorescence-based imaging and detection. These are based on `downconversion fluorescence' and have several drawbacks: photobleaching, autofluorescence, short tissue penetration depth and tissue photo-damage. Upconversion fluorescent nanoparticles (UCNs) emit detectable photons of higher energy in the short wavelength range upon irradiation with near-infrared (NIR) light based on a process termed `upconversion'. UCNs show absolute photostability, negligible autofluorescence, high penetration depth and minimum photodamage to biological tissues. Lanthanide doped nanocrystals with nearinfrared NIR-to-NIR and/or NIR-to-VIS and/or NIR-to-UV upconversion fluorescence emission have been synthesized. The nanocrystals with small size and tunable multi-color emission have been developed. The emission can be tuned by doping different upconverting lanthanide ions into the nanocrystals. The nanocrystals with core-shell structure have also been prepared to tune the emission color. The surfaces of these nanocrystals have been modified to render them water dispersible and biocompatible. They can be used for ultrasensitive interference-free biodetection because most biomolecules do not have upconversion properties. UCNs are also useful for light based therapy with enhanced efficiency, for example, photoactivation.

NAIP Status Maps Gallery

Data.gov (United States)

Farm Service Agency, Department of Agriculture — NAIP Status Maps Gallery. These maps illustrate what aerial imagery collection is planned, whats been collected, when it is available and how it is available. These...

Opportunities for Innovation Adoption in Art Galleries

Directory of Open Access Journals (Sweden)

Ieva VITKAUSKAITĖ

2016-12-01

Full Text Available This article introduces the opportunities for innovation adoption in art galleries. It provides systematised information on innovation processes and innovations used in business models of art galleries. The empirical research conducted has revealed the attitude of art galleries towards innovations, as well as the benefits and opportunities to realise them. The first part of the article distinguishes the stages of innovation process and management. The following part describes the factors that influence the management of innovation process. The final part of the article analyses the application of innovations for the improvement of a business model, with Business Model Canvas by Alexander Osterwalder and Yves Pigneur selected as the starting point for analysis and, finally, the outcomes of empirical research are provided.

Genesis of a Joint Gallery of Sport Art.

Science.gov (United States)

Kozar, Andrew J.

1989-01-01

The University of Pennsylvania's dual sport art gallery showcases the work of R. Taft McKenzie and Joe Brown, two of the premier sport artists of our time. This article briefly outlines the artists' careers and describes the planning which led to establishment of the gallery. (IAH)

Alannah Coleman: 1970—A Year at Bonython’s Sydney Gallery

Directory of Open Access Journals (Sweden)

Simon Pierse

2018-03-01

Full Text Available When art dealer and entrepreneur Kym Bonython’s new gallery opened in Sydney in 1967, it was believed to be the largest commercial gallery in the southern hemisphere. In early 1970, Bonython brought Melbourne-born art dealer Alannah Coleman over from London to take on the management of his gallery. Sadly, her appointment was not a success and lasted less than a year. Coleman re-organised the records and accounts along European lines and tried to put the gallery on a firm financial footing, but she met with opposition from staff, artists and Bonython himself. Bonython wanted the gallery as a showcase for new talent and was always on the lookout to spot ‘the next goer’. The opening parties at Bonython’s deplored by Coleman as ‘open slather’ evenings proved to be significant social events and the focus for cultural exchange, whilst in his solo shows, Brett Whiteley made innovative use of the gallery as a ‘theatre’, combining painting and sculpture with light and sound to transform the exhibition into a completely new synesthetic experience. In 1971, with funding from John Kaldor’s Public Art Project scheme, Swiss curator and gallerist Harald Szeemann used the Bonython Gallery to stage a groundbreaking show of conceptual art that went on to show at the National Gallery of Victoria, Melbourne. Without a regular external source of sponsorship or support, however, Coleman’s fears for the financial viability of the gallery were eventually proved right when, after several further years of losses, it finally closed in 1976.

Dimensioning of lining galleries in deep clays

International Nuclear Information System (INIS)

Bernaud, D.; Rousset, G.

1991-01-01

The aim of the work presented in this report is to study the mechanical behaviour of lining galleries in deep clays. This text constitutes a part of the researches on the feasibility of a geological disposal of radioactive waste, which the scope is to assure the gallery long term stabilization and also to optimize its dimensioning. In particular, we are interested here in the study of a closure controlled lining, that constitutes a direct application of the convergence-confinement method, especially well fitted to deep clays. The presentation and interpretation of the convergence controlled lining test, which was performed in the experimental gallery of Mol in Belgium, is given in this report. The instrumentation was conceived in order to find out the stress field exerced by the rockmass on the lining, the internal stress field inside the lining and the gallery closure. The analysis of all measurements results, obtained between november 1987 and December 1989, shows that they are all in good agreement and that the lining design was well chosen. Two years after the gallery construction, the average closure is of the order of 2% and the average confinement pressure is about 1.6 MPa (the third of the lithostatic pressure). The time dependent effects of the rockmass are very well modelled by the non linear elasto-viscoplastic law developed at L.M.S. with the laboratory tests. The elastic-plastic model of the lining are shown to be well fitted to simulate the sliding of the ribs. Finally, the numerical results have shown a very good agreement with the measurements results

Construction of high-dimensional universal quantum logic gates using a Λ system coupled with a whispering-gallery-mode microresonator.

Science.gov (United States)

He, Ling Yan; Wang, Tie-Jun; Wang, Chuan

2016-07-11

High-dimensional quantum system provides a higher capacity of quantum channel, which exhibits potential applications in quantum information processing. However, high-dimensional universal quantum logic gates is difficult to achieve directly with only high-dimensional interaction between two quantum systems and requires a large number of two-dimensional gates to build even a small high-dimensional quantum circuits. In this paper, we propose a scheme to implement a general controlled-flip (CF) gate where the high-dimensional single photon serve as the target qudit and stationary qubits work as the control logic qudit, by employing a three-level Λ-type system coupled with a whispering-gallery-mode microresonator. In our scheme, the required number of interaction times between the photon and solid state system reduce greatly compared with the traditional method which decomposes the high-dimensional Hilbert space into 2-dimensional quantum space, and it is on a shorter temporal scale for the experimental realization. Moreover, we discuss the performance and feasibility of our hybrid CF gate, concluding that it can be easily extended to a 2n-dimensional case and it is feasible with current technology.

Coral Reefs: A Gallery Program, Grades 7-12.

Science.gov (United States)

National Aquarium in Baltimore, MD. Dept. of Education.

Gallery classes at the National Aquarium in Baltimore give the opportunity to study specific aquarium exhibits which demonstrate entire natural habitats. The coral reef gallery class features the gigantic western Atlantic coral reef (325,000 gallons) with over 1,000 fish. The exhibit simulates a typical Caribbean coral reef and nearby sandy…

Mode coupling in hybrid square-rectangular lasers for single mode operation

Energy Technology Data Exchange (ETDEWEB)

Ma, Xiu-Wen; Huang, Yong-Zhen, E-mail: yzhuang@semi.ac.cn; Yang, Yue-De; Xiao, Jin-Long; Weng, Hai-Zhong; Xiao, Zhi-Xiong [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors and University of Chinese Academy of Sciences, Chinese Academy of Sciences, Beijing 100083 (China)

2016-08-15

Mode coupling between a square microcavity and a Fabry-Pérot (FP) cavity is proposed and demonstrated for realizing single mode lasers. The modulations of the mode Q factor as simulation results are observed and single mode operation is obtained with a side mode suppression ratio of 46 dB and a single mode fiber coupling loss of 3.2 dB for an AlGaInAs/InP hybrid laser as a 300-μm-length and 1.5-μm-wide FP cavity connected to a vertex of a 10-μm-side square microcavity. Furthermore, tunable single mode operation is demonstrated with a continuous wavelength tuning range over 10 nm. The simple hybrid structure may shed light on practical applications of whispering-gallery mode microcavities in large-scale photonic integrated circuits and optical communication and interconnection.

Promenade Among Words and Things: The Gallery as Catalogue, the Catalogue as Gallery

Directory of Open Access Journals (Sweden)

Mari Lending

2015-12-01

Full Text Available In the mid nineteenth century new casting techniques allowed for the production of huge architectural fragments. Well-selected collections could ideally display perfect series in galleries in which the visitor could wander among monuments and experience architecture history on full scale. The disembodied material of plaster was considered capable of embodying a number of modern historical taxonomies and aesthetical programs, most importantly chronology, comparison, style, and evolution. Veritable showcases of historicism, the casts could illustrate in spatial arrangements new conceptions on the history, contemporaneity and future of architecture. Plaster cast became a main medium in which to publish antiquities as novelties for grand audiences, taking the printed and published beyond the two-dimensional space of words and images. However, due to the increasing market of casts and their sheere size and weight, the reproductions as mounted in the galleries often behaved as unruly as architecture does outside curatorial control. In the end only the catalogues, the paper versions of these imaginary museums were capable to create the orders that their plaster referents constantly aspired to destroy. An important chapter in the history of the architecture museum these plaster monuments belong to a part of architectural print culture in which catalogues were curated and galleries edited. Metaphors drawn from the realm of writing saturated the discourse on the display of casts. Images and texts fluctuated and the image-objects were compared to books, paper, pages, documents and libraries but above all to illustrations inviting promenades in time and space.

Hybrid Integrated Silicon Microfluidic Platform for Fluorescence Based Biodetection

Directory of Open Access Journals (Sweden)

André Darveau

2007-09-01

Full Text Available The desideratum to develop a fully integrated Lab-on-a-chip device capable ofrapid specimen detection for high throughput in-situ biomedical diagnoses and Point-of-Care testing applications has called for the integration of some of the novel technologiessuch as the microfluidics, microphotonics, immunoproteomics and Micro ElectroMechanical Systems (MEMS. In the present work, a silicon based microfluidic device hasbeen developed for carrying out fluorescence based immunoassay. By hybrid attachment ofthe microfluidic device with a Spectrometer-on-chip, the feasibility of synthesizing anintegrated Lab-on-a-chip type device for fluorescence based biosensing has beendemonstrated. Biodetection using the microfluidic device has been carried out usingantigen sheep IgG and Alexafluor-647 tagged antibody particles and the experimentalresults prove that silicon is a compatible material for the present application given thevarious advantages it offers such as cost-effectiveness, ease of bulk microfabrication,superior surface affinity to biomolecules, ease of disposability of the device etc., and is thussuitable for fabricating Lab-on-a-chip type devices.

Whispering-gallery mode microcavity quantum-dot lasers

International Nuclear Information System (INIS)

Kryzhanovskaya, N V; Maximov, M V; Zhukov, A E

2014-01-01

This review examines axisymmetric-cavity quantum-dot microlasers whose emission spectrum is determined by whisperinggallery modes. We describe the possible designs, fabrication processes and basic characteristics of the microlasers and demonstrate the possibility of lasing at temperatures above 100 °C. The feasibility of creating multichannel optical sources based on a combination of a broadband quantum-dot laser and silicon microring modulators is discussed. (review)

Integration of Organic Light Emitting Diodes and Organic Photodetectors for Lab-on-a-Chip Bio-Detection Systems

Directory of Open Access Journals (Sweden)

Graeme Williams

2014-02-01

Full Text Available The rapid development of microfluidics and lab-on-a-chip (LoC technologies have allowed for the efficient separation and manipulation of various biomaterials, including many diagnostically relevant species. Organic electronics have similarly enjoyed a great deal of research, resulting in tiny, highly efficient, wavelength-selective organic light-emitting diodes (OLEDs and organic photodetectors (OPDs. We consider the blend of these technologies for rapid detection and diagnosis of biological species. In the ideal system, optically active or fluorescently labelled biological species can be probed via light emission from OLEDs, and their subsequent light emission can be detected with OPDs. The relatively low cost and simple fabrication of the organic electronic devices suggests the possibility of disposable test arrays. Further, with full integration, the finalized system can be miniaturized and made simple to use. In this review, we consider the design constraints of OLEDs and OPDs required to achieve fully organic electronic optical bio-detection systems. Current approaches to integrated LoC optical sensing are first discussed. Fully realized OLED- and OPD-specific photoluminescence detection systems from literature are then examined, with a specific focus on their ultimate limits of detection. The review highlights the enormous potential in OLEDs and OPDs for integrated optical sensing, and notes the key avenues of research for cheap and powerful LoC bio-detection systems.

Low threshold lasing of bubble-containing glass microspheres by non-whispering gallery mode excitation over a wide wavelength range

Energy Technology Data Exchange (ETDEWEB)

Kumagai, Tsutaru, E-mail: kumagai.t.af@m.titech.ac.jp; Kishi, Tetsuo; Yano, Tetsuji [Department of Chemistry and Materials Science, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8550 (Japan)

2015-03-21

Bubble-containing Nd{sup 3+}-doped tellurite glass microspheres were fabricated by localized laser heating technique to investigate their optical properties for use as microresonators. Fluorescence and excitation spectra measurements were performed by pumping with a tunable CW-Ti:Sapphire laser. The excitation spectra manifested several sharp peaks due to the conventional whispering gallery mode (WGM) when the pumping laser was irradiated to the edge part of the microsphere. However, when the excitation light was irradiated on the bubble position inside the microsphere, “non-WGM excitation” was induced, giving rise to numerous peaks at a broad wavelength range in the excitation spectra. Thus, efficient excitation was achieved over a wide wavelength range. Lasing threshold excited at the bubble position was much lower than that for the excitation at the edges of the microsphere. The lowest value of the laser threshold was 34 μW for a 4 μm sphere containing a 0.5 μm bubble. Efficiency of the excitation at the bubble position with broadband light was calculated to be 5 times higher than that for the edge of the microsphere. The bubble-containing microsphere enables efficient utilization of broadband light excitation from light-emitting diodes and solar light.

Science Outreach through Art: A Journal Article Cover Gallery

Science.gov (United States)

McCullough, Ian

2015-01-01

Research faculty journal covers were used to create a gallery in the Science & Technology branch library at the University of Akron. The selection, presentation, and promotion process is shared along with copyright considerations and a review of galleries used for library outreach. The event and display was a great success attracting faculty…

Celiac disease biodetection using lossy-mode resonances generated in tapered single-mode optical fibers

Science.gov (United States)

Socorro, A. B.; Corres, J. M.; Del Villar, I.; Matias, I. R.; Arregui, F. J.

2014-05-01

This work presents the development and test of an anti-gliadin antibodies biosensor based on lossy mode resonances (LMRs) to detect celiac disease. Several polyelectrolites were used to perform layer-by-layer assembly processes in order to generate the LMR and to fabricate a gliadin-embedded thin-film. The LMR shifted 20 nm when immersed in a 5 ppm anti-gliadin antibodies-PBS solution, what makes this bioprobe suitable for detecting celiac disease. This is the first time, to our knowledge, that LMRs are used to detect celiac disease and these results suppose promising prospects on the use of such phenomena as biological detectors.

Application of gallery-drilling exploration in underground uranium mining and its evaluation

International Nuclear Information System (INIS)

Chen Ruichun; Zou Guohe

1990-01-01

Combination method of gallery and drilling is an effective one in production exploration. On the basis of the 20 years practice of a uranium mine using the gallery-drilling combination method in production exploration, the advantages, applications, engineering networks, principles of application of the gallery-drilling combination method and the results of its application are described

Exhibiting Western Desert Aboriginal painting in Australia’s public galleries: an institutional analysis, 1981-2002

OpenAIRE

Jim Berryman

2012-01-01

This paper documents and analyses the exhibition history of Aboriginal painting in Australia’s public art galleries over a two-decade period. It concentrates on Western Desert acrylics but is not confined to this movement or region alone. Based on a review of catalogues from key exhibitions, it identifies three interpretative frameworks used by curators to validate the presence of Aboriginal painting in the contemporary art realm. These modes of interpretation are called the aesthetic, ethnog...

National Gallery in Prague

Czech Academy of Sciences Publication Activity Database

Mikeš, Stanislav; Haindl, Michal; Holub, Radek

2011-01-01

Roč. 2011, č. 86 (2011), s. 23-24 ISSN 0926-4981 R&D Projects: GA MŠk(CZ) LG11009 Institutional research plan: CEZ:AV0Z10750506 Keywords : virtrual reality * information system Subject RIV: BD - Theory of Information http://library.utia.cas.cz/separaty/2011/RO/haindl-national gallery in prague.pdf

Effect of Galleries on Thermal Conditions of Urban Open Areas

Directory of Open Access Journals (Sweden)

Shahab Kariminia

2016-06-01

Full Text Available Computer simulations were performed by ENVI-met model along with physical measurements in two urban squares under hot summer conditions in Isfahan, central Iran. Each scenario concentrated on adding or extending galleries in each square. The results confirmed the role of galleries on thermal conditions; however, it was found that the effectiveness of this strategy depends on the square geometry. It presented higher efficiency for the small square with higher H/W ratio. This solution is advisable for smaller squares and when the peripheral parts are frequently used compared to the middle areas. Galleries are most efficient when allowing enough natural ventilation.

A gallery approach for off-angle iris recognition

Science.gov (United States)

Karakaya, Mahmut; Yoldash, Rashiduddin; Boehnen, Christopher

2015-05-01

It has been proven that hamming distance score between frontal and off-angle iris images of same eye differs in iris recognition system. The distinction of hamming distance score is caused by many factors such as image acquisition angle, occlusion, pupil dilation, and limbus effect. In this paper, we first study the effect of the angle variations between iris plane and the image acquisition systems. We present how hamming distance changes for different off-angle iris images even if they are coming from the same iris. We observe that increment in acquisition angle of compared iris images causes the increment in hamming distance. Second, we propose a new technique in off-angle iris recognition system that includes creating a gallery of different off-angle iris images (such as, 0, 10, 20, 30, 40, and 50 degrees) and comparing each probe image with these gallery images. We will show the accuracy of the gallery approach for off-angle iris recognition.

Presence and its absences. The 17th century gallery picture

DEFF Research Database (Denmark)

Bogh, Mikkel

A discussion of how pictures made specifically for the gallery viewer in the 17th century produce certain kinds of presence in order to catch attention......A discussion of how pictures made specifically for the gallery viewer in the 17th century produce certain kinds of presence in order to catch attention...

The Habitable Zone Gallery and its Applications

Science.gov (United States)

Gelino, Dawn M.; Kane, S. R.

2012-05-01

The Habitable Zone Gallery (www.hzgallery.org) is a service to the exoplanet community which provides Habitable Zone (HZ) information for each of the exoplanetary systems with known planetary orbital parameters. The service includes a sortable table, a plot with the period and eccentricity of each of the planets with respect to their time spent in the HZ, a gallery of known systems which plot the orbits and the location of the HZ with respect to those orbits, and orbital movies. Here we discuss various educational and scientific applications of the site such as target selection, exploring planets with eccentric orbits, and investigating habitability.

Critical stages of a biodetection platform development from sensor chip fabrication to surface chemistry and assay development

Science.gov (United States)

Uludag, Yildiz

2014-06-01

Once viewed solely as a tool to analyse biomolecular interactions, biosensors are gaining widespread interest for diagnostics, biological defense, environmental and quality assurance in agriculture/food industries. Advanced micro fabrication techniques have facilitated integration of microfluidics with sensing functionalities on the same chip making system automation more convenient1. Biosensor devices relying on lab-on-a-chip technologies and nanotechnology has attracted much of attention in recent years for biological defense research and development. However, compared with the numerous publications and patents available, the commercialization of biosensors technology has significantly lagged behind the research output. This paper reviews the reasons behind the slow commercialisation of biosensors with an insight to the critical stages of a biosensor development from the sensor chip fabrication to surface chemistry applications and nanotechnology applications in sensing with case studies. In addition, the paper includes the description of a new biodetection platform based on Real-time Electrochemical ProfilingTM (REPTM) that comprises novel electrode arrays and nanoparticle based sensing. The performance of the REPTM platform has been tested for the detection of Planktothrix agardhii, one of the toxic bloom-forming cyanobacteria, usually found in shallow fresh water sources that can be used for human consumption. The optimised REPTM assay allowed the detection of P. agardhii DNA down to 6 pM. This study, showed the potential of REPTM as a new biodetection platform for toxic bacteria and hence further studies will involve the development of a portable multi-analyte biosensor based on REPTM technology for on-site testing.

Wind galleries: an instrument for environmental impact assessment

International Nuclear Information System (INIS)

Zunino, C.

1998-01-01

In the last decades wind galleries for non-aeronautic utilisation have proved to be a useful investigation tool in various fields, such as studies on environmental impact and risk assessment, associated with permanent or incidental release of harmful substances. In this framework the feasibility of a new installation has been evaluated in Italy, having as main target the reproduction of thermal stratification phenomena. The great deal of 'hazardous' industries, often in areas having a complex orography, as well as the high pollution levels in Italian cities, lead to the conclusion that a thermally stratified wind gallery might be an economically viable investment [it

Electrical resistivity tomography survey for delineating uncharted mine galleries in West Bengal, India

International Nuclear Information System (INIS)

Maillol, J.M.; Sen, N.

1999-01-01

The history of subsidence, fires, flooding and other kinds of environmental hazards related to shallow coal workings in India goes back to colonial times some 300 years ago. As coal production accelerated in modern times, so did the environmental and socio-economic drawbacks related to exploitation. In the mid-1980s, a hydropneumatic sand-stowing method was developed to fill in abandoned galleries but their exact location had to be known. Unfortunately, most of these old workings are uncharted and consequently large tracts of land cannot be stabilized. A research program making use of integrated surface, borehole and cross-hole geophysical methods was undertaken over a five-year span to try to solve this problem. Surface geophysical methods, being cheaper and faster than their cross- and downhole counterparts, were used to cover larger areas on an exploratory basis, while cross-hole methods were employed to locate more accurately one or a network of galleries to be perforated by drillhole(s) and used as a conduit for sand stowing. The authors report the results of one of the cross-hole geophysical methods: electrical resistivity tomography (ERT). A pole-dipole configuration is used and both cross-hole and surface-borehole methodologies are tested. Forward modelling and inversion of synthetic data making use of downhole and surface physical and geometrical parameters are presented first. This phase is followed by the inversion of real data. It is concluded that ERT is not applicable for the detection of dry voids, but is effective in a waterlogged environment which is estimated to represent 85--90% of the cases. In waterlogged galleries, ERT is applicable in both cross-hole and surface-downhole modes, the latter allowing a larger surface coverage at low cost. ERT is thus a reliable geophysical tool to image water-filled voids and an adequate technique to address environmental and geotechnical problems

Polymer@gold Nanoparticles Prepared via RAFT Polymerization for Opto-Biodetection

Directory of Open Access Journals (Sweden)

Sónia O. Pereira

2018-02-01

Full Text Available Colloidal gold nanoparticles (Au NPs have been used in several biological applications, which include the exploitation of size- and shape-dependent Localized Surface Plasmon Resonance (LSPR in biosensing devices. In order to obtain functional and stable Au NPs in a physiological medium, surface modification and functionalization are crucial steps in these endeavors. Reversible addition-fragmentation chain transfer (RAFT polymerization meets this need offering the possibility of control over the composition and architecture of polymeric shells coating Au NPs. Furthermore, playing with a careful choice of monomers, RAFT polymerization allows the possibility to design a polymer shell with the desired functional groups aiming at Au based nanocomposites suitable for biorecognition and biotargeting. This review provides important aspects concerning the synthesis and optical properties of Au NPs as well as concepts of RAFT polymerization. Understanding these concepts is crucial to appreciate the chemical strategies available towards RAFT-polymer coated Au core-shell nanostructures, which are here reviewed. Finally, examples of applications in opto-biodetection devices are provided and the potential of responsive “smart” nanomaterials based on such structures can be applied to other biological applications.

Theorizing How Art Gallery Interventions Impact People With Dementia and Their Caregivers.

Science.gov (United States)

Camic, Paul M; Baker, Erin L; Tischler, Victoria

2016-12-01

Dementia refers to a variety of diseases that are characterized by cognitive difficulties and an overall decline in daily living skills. Psychologically informed arts and health programs may be particularly beneficial ways of improving the lives of people with dementia and their caregivers. This study sought to better understand how programs at contemporary and traditional art galleries might play a role in the lives of people with dementia. Participants included 12 people with mild-to-moderate dementia, their 12 caregivers and 4 gallery facilitators. Those with dementia and their caregivers were engaged in art viewing followed by art making over an 8-week period. Data, collected through postintervention interviews with participants, field notes and extensive written communication between the facilitators and research team, were analyzed using grounded theory methodology to theorize how gallery-based interventions affect people with dementia and those who care for them. The emerging theory has four primary components: the art gallery is seen as being a physically valued place that provides intellectual stimulation and offers opportunities for social inclusion that can change how dementia is perceived. These components coalesced to create positive emotional and relational effects for those with dementia and caregivers. The resulting theory has potential implications for the use of gallery-based programs in dementia care within public health, healthcare, and museum/art gallery policy and practice. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Durability of visitable concrete sewer gallery under the effect of domestic wastewater

Science.gov (United States)

Salhi, Aimed; Kriker, Abdelouahed; Tioua, Tahar; Abimiloud, Youcef; Barluenga, Gonzalo

2016-07-01

The durability of concrete structures for the disposal of wastewater depends on their behavior when faced to different aggressions such as mechanics, chemical and biological, causing a deterioration often cementing matrix. The deterioration of recent evacuations wastewater infrastructure, made of reinforced concrete less than 15 years ago, has become an important concern. The aim of this study was to investigate the degradation and the factors responsible for the deterioration of the concrete visitable gallery of sewage from the town of Touggourt (south-east of Algeria). Thus, samples from different parts of the gallery were extracted and unaltered samples were selected as a reference. A degraded sample exposed to H2S gas and another sample of the gallery submerged into wastewater were analyzed to characterize the internal and external damage to the gallery as well as the chemical and mineralogical changes. These tests were complemented by a physical and mechanical characterization of the samples. The experimental results showed the strong anisotropy of both internal and external damage.

The art of compromise: the founding of the National Gallery of British Art, 1890-1892

Directory of Open Access Journals (Sweden)

Amy Woodson-Boulton

2015-03-01

Full Text Available This article argues that the press played a key role in defining the Tate Gallery by facilitating a national debate about the siting, nature, and purpose of the proposed National Gallery of British Art. Art critics, politicians, journalists and a variety of newspaper editors weighed in on whether Britain should create a museum of modern art, a museum of national art, or both. The understanding of British art as quintessentially modern at the time of the founding of the Gallery meant that from the beginning the Tate Gallery was founded as both the National Gallery of British Art and a museum of modern art. The changing definition of modern art in the twentieth century, however, created fractures between these two identities that eventually led to the split between Tate Britain and Tate Modern.

Wavelength shift in a whispering gallery microdisk due to bacterial sensing: A theoretical approach

Directory of Open Access Journals (Sweden)

Hala Ghali

2017-04-01

Full Text Available Whispering gallery mode microcavities have recently been studied as a means to achieve real-time label-free detection of biological targets such as virus particles, specific DNA sequences, or proteins. Binding of a biomolecule to the surface of a microresonator will increase its path length, leading to a shift in the resonance frequency according to the reactive sensing principle. In this paper, we develop a theoretical expression that will link the reactive shift to the bacteria and microdisk parameters and help quantify the number of bacteria that bind to the surface of a 200μm-diameter silica microdisk. Keywords: Optical microdisk, Wavelength shift, Bacterial sensing

Rael Artel Gallery Tartus ja Varssavis

Index Scriptorium Estoniae

2006-01-01

Rael Artel Gallery : Non-Profit Project Space'i tegevusest Tartus. 27.04-27.05. 2006 Varssavis Warszawski Aktyw Artystov'i ruumides näitus "Estonian Video Art. The blood project", osalesid Flo Kasearu, Gert Hatsukov, Külli K. Kaats, Allan Tõnissoo, Marko Nautras, Tanja Muravskaja ja Airi Triisberg

PEG Functionalization of Whispering Gallery Mode Optical Microresonator Biosensors to Minimize Non-Specific Adsorption during Targeted, Label-Free Sensing

Directory of Open Access Journals (Sweden)

Fanyongjing Wang

2015-07-01

Full Text Available Whispering Gallery Mode (WGM optical microresonator biosensors are a powerful tool for targeted detection of analytes at extremely low concentrations. However, in complex environments, non-specific adsorption can significantly reduce their signal to noise ratio, limiting their accuracy. To overcome this, poly(ethylene glycol (PEG can be employed in conjunction with appropriate recognition elements to create a nonfouling surface capable of detecting targeted analytes. This paper investigates a general route for the addition of nonfouling elements to WGM optical biosensors to reduce non-specific adsorption, while also retaining high sensitivity. We use the avidin-biotin analyte-recognition element system, in conjunction with PEG nonfouling elements, as a proof-of-concept, and explore the extent of non-specific adsorption of lysozyme and fibrinogen at multiple concentrations, as well as the ability to detect avidin in a concentration-dependent fashion. Ellipsometry, contact angle measurement, fluorescence microscopy, and optical resonator characterization methods were used to study non-specific adsorption, the quality of the functionalized surface, and the biosensor’s performance. Using a recognition element ratio to nonfouling element ratio of 1:1, we showed that non-specific adsorption could be significantly reduced over the controls, and that high sensitivity could be maintained. Due to the frequent use of biotin-avidin-biotin sandwich complexes in functionalizing sensor surfaces with biotin-labeled recognition elements, this chemistry could provide a common basis for creating a non-fouling surface capable of targeted detection. This should improve the ability of WGM optical biosensors to operate in complex environments, extending their application towards real-world detection.

Real-time biodetection using a smartphone-based dual-color surface plasmon resonance sensor

Science.gov (United States)

Liu, Qiang; Yuan, Huizhen; Liu, Yun; Wang, Jiabin; Jing, Zhenguo; Peng, Wei

2018-04-01

We proposed a compact and cost-effective red-green dual-color fiber optic surface plasmon resonance (SPR) sensor based on the smartphone. Inherent color selectivity of phone cameras was utilized for real-time monitoring of red and green color channels simultaneously, which can reduce the chance of false detection and improve the sensitivity. Because there are no external prisms, complex optical lenses, or diffraction grating, simple optical configuration is realized. It has a linear response in a refractive index range of 1.326 to 1.351 (R2 = 0.991) with a resolution of 2.3 × 10 - 4 RIU. We apply it for immunoglobulin G (IgG) concentration measurement. Experimental results demonstrate that a linear SPR response was achieved for IgG concentrations varying from 0.02 to 0.30 mg / ml with good repeatability. It may find promising applications in the fields of public health and environment monitoring owing to its simple optics design and applicability in real-time, label-free biodetection.

Evaluating two infiltration gallery designs for managed aquifer recharge using secondary treated wastewater.

Science.gov (United States)

Bekele, Elise; Toze, Simon; Patterson, Bradley; Fegg, Wolfgang; Shackleton, Mark; Higginson, Simon

2013-03-15

As managed aquifer recharge (MAR) becomes increasingly considered for augmenting water-sensitive urban areas, fundamental knowledge of the achievable scale, longevity and maintenance requirements of different options will become paramount. This paper reports on a 39 month pilot scale MAR scheme that infiltrated secondary treated wastewater through unsaturated sand into a limestone and sand aquifer. Two types of infiltration gallery were constructed to compare their hydraulic performance, one using crushed, graded gravel, the other using an engineered leach drain system (Atlantis Leach System(®)). Both galleries received 25 kL of nutrient-rich, secondary treated wastewater per day. The Atlantis gallery successfully infiltrated 17 ML of treated wastewater over three years. The slotted distribution pipe in the gravel gallery became clogged with plant roots after operating for one year. The infiltration capacity of the gravel gallery could not be restored despite high pressure cleaning, thus it was replaced with an Atlantis system. Reduction in the infiltration capacity of the Atlantis system was only observed when inflow was increased by about 3 fold for two months. The performance of the Atlantis system suggests it is superior to the gravel gallery, requiring less maintenance within at least the time frame of this study. The results from a bromide tracer test revealed a minimum transport time of 3.7 days for the recharged water to reach the water table below 9 m of sand and limestone. This set a limit on the time available for attenuation by natural treatment within the unsaturated zone before it recharged groundwater. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Whispering gallery modes for elastic waves in disk resonators

Directory of Open Access Journals (Sweden)

S. Kaproulias

2011-12-01

Full Text Available The resonant modes of elastic waves in disk resonators are computationally studied with the finite difference time domain method. Different materials examined for the disk such as platinum and silicon. The effect of a glass substrate is also important especially in the case of silicon disks because of the similarity of sound velocities and mass densities between the two materials. The possibility of using those structures as sensors is also considered.

The Cosmology Gallery: Unity through diversity in a vast and awe-inspiring universe.

Science.gov (United States)

Goldsmith, John

2011-06-01

Scientists, artists, religious and cultural leaders have come together to create the Cosmology Gallery at the Gravity Discovery Centre (GDC) located 70 km north of Perth, Western Australia. The Cosmology Gallery exhibitions include the multicultural cosmology artworks, Celestial Visions astronomical photography exhibition and the Timeline of the Universe. The multicultural cosmology artworks are new artworks inspired by Australian Indigenous, Christian, Buddhist, Islamic, Hindu, scientific and technological perspectives of the universe. The Celestial Visions exhibition features astronomical events above famous landmarks, including Stonehenge and the Pyramids. The AUD 400,000+ project was funded by Lotterywest, Western Australia and the Cosmology Gallery was officially opened in July 2008 by the Premier of Western Australia.

Thermal simulation of storage in TSS-Galleries

International Nuclear Information System (INIS)

Lain Huerta, R.; Martinez Santiago, T.; Ramirez Oyangueren, P.

1993-01-01

This report describes the experiment ''thermal simulation of storage in TSS-galleries'' what is been developed in salt mine of Asse, Germany. The report has 3 part: 1) Analysis of objectives and general description of boundary layers. 2) Geomechanics parameters of salt mine. 3) Thermal modelization, thermomechanics modelization and data acquisition

Viability of microcomputed tomography to study tropical marine worm galleries in humid muddy sediments

Energy Technology Data Exchange (ETDEWEB)

Pennafirme, Simone F., E-mail: sipennafirme@gmail.com [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Inst. de Biologia. Dept. de Biologia Marinha; Machado, Alessandra S.; Lima, Inaya; Suzuki, Katia N.; Lopes, Ricardo T., E-mail: machado@lin.ufrj.br, E-mail: inaya@lin.ufrj.br, E-mail: norisuzuki6@yahoo.com.br, E-mail: ricardo@lin.ufj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), RJ (Brazil). Lab. de Instrumentacao Nuclear

2013-07-01

Bioturbation is an ecological process driven by organisms, which transports nutrients and gases from air/water to sediment through their galleries, by the time they feed, burrow and/or construct galleries. This exchange is vital to the maintenance of micro and macrobenthic organisms, mainly in muddy flat environments. Species with distinct galleries could create levels of bioturbation, affecting the benthic interactions. In this sense, it is fundamental developing a non-destructive method that permits identifying/quantifying the properties of these galleries. The recent advances in micro-computed tomography are allowing the high resolution 3D images generation. However, once muddy sediments are rich in organic matter and interstitial water, these would lead to motion artifacts which could, in turn, decrease the accuracy of galleries identification/quantification. In this context, the aim of this study was to develop a protocol which combines laboratory experiments and microtomography analysis in order to generate accurate 3D images of the small marine worm's galleries within humid muddy sediments. The sediment was collected at both muddy flats of Surui's and Itaipu lagoon's mangroves (RJ-Brazil), sieved (0.5mm mesh) and introduced with one individual of the marine worm Laeonereis acuta (Nereididae, Polychaeta) in each acrylic corer holders (4.4cm of internal diameter). High energy microtomography scanner was used to obtain 3D images and the setup calibration was 130 kV and 61 mA. Each acquisition image time was among 4h and 6h. Several procedures of drying remained water inside the cores were performed aiming obtaining images without movement artifacts due to circulating water, and this issue was one of the main studied parameter. In order to investigate possible chemical effects, 2ml of formalin (35%) with menthol were added to the surface of the cores. The results show that although the drying time was appropriated, the chemicals created bubbles

Viability of microcomputed tomography to study tropical marine worm galleries in humid muddy sediments

International Nuclear Information System (INIS)

Pennafirme, Simone F.; Machado, Alessandra S.; Lima, Inaya; Suzuki, Katia N.; Lopes, Ricardo T.

2013-01-01

Bioturbation is an ecological process driven by organisms, which transports nutrients and gases from air/water to sediment through their galleries, by the time they feed, burrow and/or construct galleries. This exchange is vital to the maintenance of micro and macrobenthic organisms, mainly in muddy flat environments. Species with distinct galleries could create levels of bioturbation, affecting the benthic interactions. In this sense, it is fundamental developing a non-destructive method that permits identifying/quantifying the properties of these galleries. The recent advances in micro-computed tomography are allowing the high resolution 3D images generation. However, once muddy sediments are rich in organic matter and interstitial water, these would lead to motion artifacts which could, in turn, decrease the accuracy of galleries identification/quantification. In this context, the aim of this study was to develop a protocol which combines laboratory experiments and microtomography analysis in order to generate accurate 3D images of the small marine worm's galleries within humid muddy sediments. The sediment was collected at both muddy flats of Surui's and Itaipu lagoon's mangroves (RJ-Brazil), sieved (0.5mm mesh) and introduced with one individual of the marine worm Laeonereis acuta (Nereididae, Polychaeta) in each acrylic corer holders (4.4cm of internal diameter). High energy microtomography scanner was used to obtain 3D images and the setup calibration was 130 kV and 61 mA. Each acquisition image time was among 4h and 6h. Several procedures of drying remained water inside the cores were performed aiming obtaining images without movement artifacts due to circulating water, and this issue was one of the main studied parameter. In order to investigate possible chemical effects, 2ml of formalin (35%) with menthol were added to the surface of the cores. The results show that although the drying time was appropriated, the chemicals created bubbles within the

Measurements of indoor 222Rn concentration in two art galleries

International Nuclear Information System (INIS)

Carneiro, Luana Gomes; Braz, Delson; Jesus, Edgar Francisco de; Cunha, Kenya Dias da; Medeiros, Geiza; Zouain, Felipe; Pitassi, Gabriel; Leite, Carlos Barros; Cardoso, Katia

2009-01-01

It is point out that radon and their decay products in environment give high dose to human lung. Studies indicate that the indoor radon inhalation by humans has been considered probably the second most important cause of lung cancer after of smoking. A passive-type radon detector was used for measuring indoor radon concentration in two art galleries at Rio de Janeiro city during 90 days January to March, 2009. The aim of this study is to evaluate the occupational and public radon exposure in art galleries and museums. This paper shows the preliminary results of samples collected at two art galleries located in Gavea, Rio de Janeiro city. 30 LEXAN (GE) track detectors were exposed in the air (indoor as well as outdoor). The samples were collected in the same building which is a construction of XIX century. The analysis of the results suggests that the 222 Rn concentration levels are different in both sampling site, in closed environmental, demonstrating that, although the construction materials are the same the absence of circulating air is a factor very important to increase the concentration of indoor Rn. (author)

Krasotshnõje snõ Sed Arte Gallery / Irina Butjajeva

Index Scriptorium Estoniae

Butjajeva, Irina

2007-01-01

Valgevene kunstnike Jelena Shlegeli, Vladimir Gontsharuki, Dmitri Zenkovitshi ja Dmitri Masli maalinäitus "Valgevene värvilised unenäod" Tallinna galeriis Aatrium. Näitust vahendas Sed Arte Gallery, galerist Olga Ljubaskina

InfoGallery: Informative Arts Services for Physical Library Spaces

DEFF Research Database (Denmark)

Grønbæk, Kaj; Rohde, Anne; Sundararajah, Balasuthas

2006-01-01

Much focus in digital libraries research has been devoted to new online services rather than services for the visitors in the physical library. This paper describes InfoGallery, which is a web-based infrastructure for enriching the physical library space with informative art "exhibitions......" of digital library material and other relevant information, such as RSS news streams, event announcements etc. InfoGallery presents information in an aesthetically attractive manner on a variety of surfaces in the library, including cylindrical displays and floors. The infrastructure consists of a server...... structure, an editor application and a variety of display clients. The paper discusses the design of the infrastructure and its utilization of RSS, podcasts and manually edited news. Applications in the library domain are described and the experiences are discussed....

Lab, Field, Gallery and Beyond

DEFF Research Database (Denmark)

Binder, Thomas; Koskinen, Ilpo; Redström, Johan

2009-01-01

Over the last ten years we have seen a growing number of researchers integrating design experiments in their research inquiries. Initially, this work borrowed heavily from neighboring fields, employing a dual strategy in which design experiments and their evaluation were largely treated as separate...... processes that were often carried out by different people. More recently, design researchers have developed several approaches that integrate design-specific work methods to research. This paper takes a methodological look at three such established approaches that we call Lab, Field, and Gallery. We...

Absorptive lasing mode suppression in ZnO nano- and microcavities

Energy Technology Data Exchange (ETDEWEB)

Wille, M.; Michalsky, T.; Krüger, E.; Grundmann, M.; Schmidt-Grund, R. [Universität Leipzig, Institut für Experimentelle Physik II, Linnéstraße 5, 04103 Leipzig (Germany)

2016-08-08

We conclusively explain the different lasing mode energies in ZnO nano- and microcavities observed by us and reported in literature. The limited penetration depth of usually used excitation lasers results in an inhomogeneous spatial gain region depending on the structure size and geometry. Hence, weakly or even nonexcited areas remain present after excitation, where modes are instantaneously suppressed by excitonic absorption. We compare the effects for ZnO microwires, nanowires, and tetrapod-like structures at room temperature and demonstrate that the corresponding mode selective effect is most pronounced for whispering-gallery modes in microwires with a hexagonal cross section. Furthermore, the absorptive lasing mode suppression will be demonstrated by correlating the spot size of the excitation laser and the lasing mode characteristic of a single ZnO nanowire.

Whispering galleries and the control of artificial atoms.

Science.gov (United States)

Forrester, Derek Michael; Kusmartsev, Feodor V

2016-04-28

Quantum computation using artificial-atoms, such as novel superconducting circuits, can be sensitively controlled by external electromagnetic fields. These fields and the self-fields attributable to the coupled artificial-atoms influence the amount of quantum correlation in the system. However, control elements that can operate without complete destruction of the entanglement of the quantum-bits are difficult to engineer. Here we investigate the possibility of using closely-spaced-linear arrays of metallic-elliptical discs as whispering gallery waveguides to control artificial-atoms. The discs confine and guide radiation through the array with small notches etched into their sides that act as scatterers. We focus on π-ring artificial-atoms, which can generate their own spontaneous fluxes. We find that the micro-discs of the waveguides can be excited by terahertz frequency fields to exhibit whispering-modes and that a quantum-phase-gate composed of π-rings can be operated under their influence. Furthermore, we gauge the level of entanglement through the concurrence measure and show that under certain magnetic conditions a series of entanglement sudden-deaths and revivals occur between the two qubits. This is important for understanding the stability and life-time of qubit operations using, for example, a phase gate in a hybrid of quantum technologies composed of control elements and artificial-atoms.

Museums and art galleries as partners for public health interventions.

Science.gov (United States)

Camic, Paul M; Chatterjee, Helen J

2013-01-01

The majority of public health programmes are based in schools, places of employment and in community settings. Likewise, nearly all health-care interventions occur in clinics and hospitals. An underdeveloped area for public health-related planning that carries international implications is the cultural heritage sector, and specifically museums and art galleries. This paper presents a rationale for the use of museums and art galleries as sites for public health interventions and health promotion programmes through discussing the social role of these organisations in the health and well-being of the communities they serve. Recent research from several countries is reviewed and integrated into a proposed framework for future collaboration between cultural heritage, health-care and university sectors to further advance research, policy development and evidence-based practice.

Engaging Families in the Galleries Using Design Thinking

Science.gov (United States)

Larson, Lucy

2017-01-01

The Palo Alto Art Center sought a solution to the challenge that loyal family audiences, visiting weekly for art studio classes, rarely visit the contemporary art exhibition galleries. This article relates the experience of using the human-centered design process, often called Design Thinking, as the methodology to create a solution for family…

A gallery support

Energy Technology Data Exchange (ETDEWEB)

Erokhin, A I; Orekhov, D M; Romanov, P D; Semenov, U N; Sokov, G D; Trubnikov, V P

1981-10-15

The gallery support includes a middle section consisting of forward and aft hydraulic walls, a roof timber and a foundation on which the cross beam is connected to a longitudinal element, and outer sections mounted on both sides of the longitudinal element behind the cross beam; these outer sections contain the roof timbers, the hydraulic walls and the foundations which are connected to the cross beam by a hydraulic jack. In order to increase the areas where it may be used, particularly for variable-level mining works, the connector between the longitudinal element and the cross beam is hinge mounted, while the roof timbers of the outer sections are connected together by an adjustible jack and are constructed to allow detachable beams to be mounted on them under the arched support; the forward hydraulic props of the mid section are mounted on the ends of the cross beam.

What Can the Habitable Zone Gallery Do For You?

Science.gov (United States)

Gelino, Dawn M.; Kane, Stephen

2015-12-01

The Habitable Zone Gallery (www.hzgallery.org) came online in August 2011 as a service to the exoplanet community that provides Habitable Zone (HZ) information for each of the exoplanetary systems with known planetary orbital parameters. The service includes a sortable table, a plot with the period and eccentricity of each of the planets with respect to their time spent in the HZ, a gallery of known systems which plot the orbits and the location of the HZ with respect to those orbits, and orbital movies. Recently, we have added new features including: implementation of both conservative and optimistic HZs, more user-friendly table and movies, movies for circumbinary planets, and a count of planets whose orbits lie entirely within the system's HZ. Here we discuss various educational and scientific applications of the site such as target selection, exploring planets with eccentric or circumbinary orbits, and investigating habitability.

The whispering gallery as an optical component in the X-ray region

International Nuclear Information System (INIS)

Howells, M.R.

1995-08-01

The whispering gallery phenomenon in acoustics has been known and studied for more than a century, and the same effect has been observed to take place with waves other than sound waves. In this paper we review the theoretical basis and attractive features of the whispering gallery as a soft x-ray optical component and indicate some of its potential applications. We then describe what may be its most unique capability which, in favorable cases, is to provide a way. to manipulate the phase difference between the s and p polarization components and thus to generate circularly or elliptically polarized soft x-rays

Exhibiting Western Desert Aboriginal painting in Australia’s public galleries: an institutional analysis, 1981-2002

Directory of Open Access Journals (Sweden)

Jim Berryman

2012-12-01

Full Text Available This paper documents and analyses the exhibition history of Aboriginal painting in Australia’s public art galleries over a two-decade period. It concentrates on Western Desert acrylics but is not confined to this movement or region alone. Based on a review of catalogues from key exhibitions, it identifies three interpretative frameworks used by curators to validate the presence of Aboriginal painting in the contemporary art realm. These modes of interpretation are called the aesthetic, ethnographic and the ownership discourses. Despite being a problematic art at odds with conventional art-historical classifications, Aboriginal painting was elevated to a position of prominence in Australian art history. Institutionally, Western Desert painting found legitimacy in the dominant aesthetic legacy of modernism. This modernist art historiography overrode the minority interests of cultural pluralism and critical postmodernism.

Experiences from a Real-Time Mobile Collaborative Writing System in an Art Gallery

DEFF Research Database (Denmark)

Korn, Matthias; Polli, Anna Maria; Klokmose, Clemens Nylandsted

We present first experiences from Local Area Artworks, a system enabling collaborative art interpretation on-site, deployed during an exhibition in a local art gallery. Through the system, we explore ways to re-connect people to local places by making use of their personal mobile devices...... as interfaces to the shared physical space. With a collocated collaborative writing system in the semi-public space of a gallery, we encourage local art discussions and provide a platform for the public to actively participate in interpretations of individual artworks. In this paper, we focus on the experiences...

Analysis of high-quality modes in open chaotic microcavities

International Nuclear Information System (INIS)

Fang, W.; Yamilov, A.; Cao, H.

2005-01-01

We present a numerical study of the high-quality modes in two-dimensional dielectric stadium microcavities. Although the classical ray mechanics is fully chaotic in a stadium billiard, all of the high-quality modes show a 'strong scar' around unstable periodic orbits. When the deformation (ratio of the length of the straight segments over the diameter of the half circles) is small, the high-quality modes correspond to whispering-gallery-type trajectories and their quality factors decrease monotonically with increasing deformation. At large deformation, each high-quality mode is associated with multiple unstable periodic orbits. Its quality factor changes nonmonotonically with the deformation, and there exists an optimal deformation for each mode at which its quality factor reaches a local maximum. This unusual behavior is attributed to the interference of waves propagating along different constituent orbits that could minimize light leakage out of the cavity

Mechanical behavior of galleries in deep clay - Study of a concrete example

International Nuclear Information System (INIS)

Rousset, G.; Jehan, R.A.; Bonne, A.; Fernique, J.C.

1985-01-01

At important depths such as those envisaged for the construction of a radioactive waste disposal, clay appears to be a material of rather weak resistance. One of the first problems to be studied is the technical feasibility of a disposal facility. The time-dependent and strain-softening behavior of the clay plays a significant role in the long term stability of the lined galleries. The in-situ measurements carried out during the digging of a gallery in Boom clay (Belgium), under a 250 m overburden are presented. The data obtained are analyzed by means of an elastoviscoplastic model including strain softening behavior of the clay

Calcium fluoride whispering gallery mode optical resonator with reduced thermal sensitivity

Science.gov (United States)

Savchenkov, Anatoliy; Matsko, Andrey

2018-03-01

We demonstrate a crystalline CaF2 resonator with thermal sensitivity of the optical modes approaching zero. The resonator is made by laminating a calcium fluoride layer forming an optical monolithic cavity with ceramic compensation layers. The ceramics is characterized with negative thermal expansion coefficient achievable in a certain temperature range. The thermally compensated resonator has a potential application for laser frequency stabilization.

On the Problem of Filtration to an Imperfect Gallery in a Pressureless Bed

Science.gov (United States)

Bereslavskii, É. N.; Dudina, L. M.

2018-01-01

The problem of plane steady-state filtration in a pressureless bed to an imperfect gallery in the presence of evaporation from the flow free surface is considered. To study such type of flow, a mixed boundary-value problem of the theory of analytical functions is formulated and solved with application of the Polubarinova-Kochina method. Based on the model suggested, an algorithm for computing the discharge of the gallery and the ordinate of free surface emergence to the impermeable screen is developed. A detailed hydrodynamic analysis of the influence of all physical parameters of the model on the desired filtration characteristics is given.

Microwave oscillator with 'whispering gallery' resonator

International Nuclear Information System (INIS)

Kirichenko, A.Ya.; Prokopenko, Yu.V.; Filippov, Yu.F.; Lonin, Yu.F.; Papkovich, V.G.; Ponomarev, A.G.; Prokopenko, Yu.V.; Uvarov, V.T.

2010-01-01

It was presented researches of a generation of microwave radiation into system with azimuthally periodical relativistic electron beam current that excites a high-Q quasi-optical dielectric resonator. The Eigen parameters of cylindrical Teflon resonator were determined by numerical computation. Registration of the microwave radiation realizes by a crystal set of 8-mm wavelength range. Research projects of microwave oscillators with high-Q resonators, in which 'whispering gallery' oscillations are excited by an electron flow, are presented. Multiresonator oscillators ideology is based on principles of microwave generation in klystrons with both subcritical and supercritical electron beams currents.

Memorializing the Wars of Religion in Early Seventeenth-Century French Picture Galleries : Protestants and Catholics Painting the Contested Past

NARCIS (Netherlands)

van der Linden, David

2017-01-01

This article examines how Protestant and Catholic elites in early seventeenth-century France memorialized the Wars of Religion in purpose-built picture galleries. Postwar France remained a divided nation, and portrait galleries offered a sectarian memory of the conflict, glorifying party heroes.

Reporting on What Jane Saw 2.0: Female Celebrity and Sensationalism in Boydell’s Shakespeare Gallery

Directory of Open Access Journals (Sweden)

Janine Barchas

2015-03-01

Full Text Available This essay reports on ongoing efforts to build an accurate digital model of John Boydell’s popular Shakespeare Gallery precisely as it looked in August 1796—when a 20-year-old Jane Austen visited London’s sites, staying within a ten-minute walk from the gallery. The essay argues for the substantial difference between studying Boydell’s pictures in a paper volume (whether as lists, illustrations in books, or engraved folio plates and viewing them as an exhibition of paintings on walls, albeit virtual ones. For example, the digital reconstruction illuminated commissions from several female participants in Boydell’s male-dominated gallery, especially Angelica Kauffman (1741-1807 and Anne Seymour Damer (1749-1828. In addition, the essay also recounts how the celebrity of model Emma Hart/Hamilton (1765-1815 safeguarded one Boydell painting from oblivion while The Shakespeare Gallery proved the site of a strange form of self-promotion practiced by actress Mary Wells (1762-1829. Our digital visualization of an historic exhibition in 1796 brought the controversial celebrity of a few women artists into focus. In sum, this essay shows DH methodology in action while sampling what might be gleaned when digital tools serve historical scholarship in the humanities.

Efficient analysis of mode profiles in elliptical microcavity using dynamic-thermal electron-quantum medium FDTD method.

Science.gov (United States)

Khoo, E H; Ahmed, I; Goh, R S M; Lee, K H; Hung, T G G; Li, E P

2013-03-11

The dynamic-thermal electron-quantum medium finite-difference time-domain (DTEQM-FDTD) method is used for efficient analysis of mode profile in elliptical microcavity. The resonance peak of the elliptical microcavity is studied by varying the length ratio. It is observed that at some length ratios, cavity mode is excited instead of whispering gallery mode. This depicts that mode profiles are length ratio dependent. Through the implementation of the DTEQM-FDTD on graphic processing unit (GPU), the simulation time is reduced by 300 times as compared to the CPU. This leads to an efficient optimization approach to design microcavity lasers for wide range of applications in photonic integrated circuits.

[Concordance among analysts from Latin-American laboratories for rice grain appearance determination using a gallery of digital images].

Science.gov (United States)

Avila, Manuel; Graterol, Eduardo; Alezones, Jesús; Criollo, Beisy; Castillo, Dámaso; Kuri, Victoria; Oviedo, Norman; Moquete, Cesar; Romero, Marbella; Hanley, Zaida; Taylor, Margie

2012-06-01

The appearance of rice grain is a key aspect in quality determination. Mainly, this analysis is performed by expert analysts through visual observation; however, due to the subjective nature of the analysis, the results may vary among analysts. In order to evaluate the concordance between analysts from Latin-American rice quality laboratories for rice grain appearance through digital images, an inter-laboratory test was performed with ten analysts and images of 90 grains captured with a high resolution scanner. Rice grains were classified in four categories including translucent, chalky, white belly, and damaged grain. Data was categorized using statistic parameters like mode and its frequency, the relative concordance, and the reproducibility parameter kappa. Additionally, a referential image gallery of typical grain for each category was constructed based on mode frequency. Results showed a Kappa value of 0.49, corresponding to a moderate reproducibility, attributable to subjectivity in the visual analysis of grain images. These results reveal the need for standardize the evaluation criteria among analysts to improve the confidence of the determination of rice grain appearance.

Ultrasonic sounding and monitoring of the excavation damaged zone in a soft supported gallery

International Nuclear Information System (INIS)

Balland, Cyrille; Souley, Mountaka; Morel, Jacques

2012-01-01

Document available in extended abstract form only. Under high in situ stresses and high anisotropic stress ratios, the excavation of underground openings generally causes the creation of a disturbed (EdZ: Excavation disturbed Zone) and/or damaged (EDZ: Excavation Damaged Zone) zone, resulting from the initiation and growth of cracks and fractures and by a redistribution and rearrangement of the initial stresses. Due to the modifications of mechanical and hydro-mechanical properties in the EdZ/EDZ, the latter constitute a potential risk for the efficiency of the geologic and/or engineered barriers. To estimate the performance of a site of radioactive waste storage, it is essential to know the geometry, the extensions of the EdZ/EDZ, the density of cracks, their connectivity and the variations of permeability which can result from it. In particular, their extension depends on numerous factors among which the nature of the rock, the pre-existent fractures and their reactivation, the initial stress field (magnitudes and/or rate of anisotropy), the time, the geometry and the techniques of excavations etc.. In addition, the evolution of EdZ/EDZ properties in the medium term is little or poorly known, particularly under the influence of environmental conditions such as the re-confining by near field rock creep in contact with a rigid structural support or the evolution of hydric conditions (desaturation and re-saturation). Ultrasonic experimentation under the OHZ experiment has been implemented to characterize the EDZ extension and its evolution in time according to the structural support type (soft or rigid) and the environmental conditions present in the laboratory. This study consists of two experimental components: (1) the prior auscultation of the sole and face of the gallery by ultrasonic transmission tomography, (2) the monitoring the EDZ and the analysis of measurable changes in the propagation of ultrasonic waves in the medium term. Mechanical modelling of the

Whispering gallery effect in relativistic optics

Science.gov (United States)

Abe, Y.; Law, K. F. F.; Korneev, Ph.; Fujioka, S.; Kojima, S.; Lee, S.-H.; Sakata, S.; Matsuo, K.; Oshima, A.; Morace, A.; Arikawa, Y.; Yogo, A.; Nakai, M.; Norimatsu, T.; d'Humières, E.; Santos, J. J.; Kondo, K.; Sunahara, A.; Gus'kov, S.; Tikhonchuk, V.

2018-03-01

relativistic laser pulse, confined in a cylindrical-like target, under specific conditions may perform multiple scattering along the internal target surface. This results in the confinement of the laser light, leading to a very efficient interaction. The demonstrated propagation of the laser pulse along the curved surface is just yet another example of the "whispering gallery" effect, although nonideal due to laser-plasma coupling. In the relativistic domain its important feature is a gradual intensity decrease, leading to changes in the interaction conditions. The proccess may pronounce itself in plenty of physical phenomena, including very efficient electron acceleration and generation of relativistic magnetized plasma structures.

The Habitable Zone Gallery 2.0: The Online Exoplanet System Visualization Suite

Science.gov (United States)

Chandler, C. O.; Kane, S. R.; Gelino, D. M.

2017-11-01

The Habitable Zone Gallery 2.0 provides new and improved visualization and data analysis tools to the exoplanet habitability community and beyond. Modules include interactive habitable zone plotting and downloadable 3D animations.

Australian doctors and the visual arts. Part 4. Doctors as supporters of art galleries and artists in Victoria.

Science.gov (United States)

Hamilton, D G

1986-07-07

The contribution of doctors to the visual arts is being discussed in a series of six articles. Doctor-artists in New South Wales and Victoria, and doctors as collectors, donors, gallery supporters and writers in New South Wales, have been discussed in earlier articles. This, the fourth article, deals with doctors as supporters of art galleries and artists in Victoria.

Introducing New Library Services: Nuclear Malaysia Gallery Photos and Videos

International Nuclear Information System (INIS)

Mohd Hafizal Yusof; Nasaruddin Ahmad; Habibah Adnan

2015-01-01

The main purpose of the existing of library is to preserve books and journals for the organizations main business. The role of library itself is to organize the books such as borrowing and renewal services as consulting their customers on getting the best references for the customers need and demand. Nowadays, the role of library also expands and the need for storing and preserving non-monograph resources such as photo and video also increase. Follow that current situation, Nuclear Malaysia's Library also take a step forwards by introducing new services so called Photo and Video Gallery. Realizing that Nuclear Malaysia also have their valuable photo and video that contains so called memorable moment and must be preserve for future reference, the management of Nuclear Malaysia's Library have decided to buy the system so called P-Canvas. The main purpose of this paper is to explain the library new services, Photo and Video Gallery, development and advantage of this system in storing and preserving Nuclear Malaysia's photo and video. (author)

Community Litter Arthropods Associated cerrado and gallery forest, in the Ecological Station Sierra Das Araras - Mato Grosso, Brazil

Directory of Open Access Journals (Sweden)

Daniela Cristina Zardo

2015-12-01

Full Text Available The litter arthropod fauna distinguishes itself by its importance in nutrient cycling and organic matter degradation. This invertebrate fauna has been emphasized as crucial for the processes that structure ecosystems. This study aims to evaluate and compare the arthropod fauna composition, richness and abundance in litter of two environments: the savanna and the gallery forest at Serra das Araras Ecological Station , Mato Grosso. To collect the arthropods a 120m transects for each habitat was delimited, divided into six points in each environment. For all the litter collection points, we marked a plot measuring 1.0 x 1.0 m, totalizing 6m2 for an environment, where the arthropods found were identified by order level, and the individuals were grouped into morphospecies. The total arthropods richness found in the savanna and in the gallery forest areas was 38 morphospecies, 28 morphospecies were found in the savanna and 20 in the gallery forest, with total abundance of 381 individuals, being 226 individuals collected in the savanna and 155 individuals in the gallery forest. The more abundant morphospecies in the savanna and gallery forest belonged to Hymenoptera and Isoptera orders, with 10 and 4 morphospecies and abundance of 263 and 78 individuals respectively. The greatest organism richness and abundance occurred in the savanna, because it is a tropical environment with the greatest biodiversity, especially regarding its insect fauna, and this diversity is primarily concerned with the variety of habitats that the environment provides , which gives the species shelter, food and reproduction sites.

A study of grandparents and grandchildren as visitors to museums and art galleries in the UK

Directory of Open Access Journals (Sweden)

Ela Beaumont

2005-11-01

Full Text Available This paper discusses one aspect of a major research project funded by the Arts and Humanities Research Council of family group visitors to museums and galleries in the UK. Grandparents visiting with their grandchildren are a little understood phenomenon in terms of visitor research and this paper aims to address that balance. The research project focuses on three art galleries and museums in the UK where 44 sets of grandparents were interviewed during the initial stages of the research. Findings have shown a number of interesting facets, some of which are presented in this paper. Grandparents are motivated to visit the museum with their grandchildren in the main because they are seeking an entertaining visit, a day out that is also educational and linked to school projects. They are likely to be the children’s primary carers as parents are out to work and the destination might not link with their own interests but those of the parents. They have social roles to play in their grandchildren’s lives. They often seek activity or workshops in the museum/art gallery that will be of benefit for their grandchildren and encourage them to explore the activities provided. These and other aspects are discussed within the paper. We conclude by suggesting how the findings can be used to inform more sophisticated approaches to ‘family friendly’ initiatives in museums and art galleries.

The role of gallery forests in maintaining Phlebotominae populations: potential Leishmania spp. vectors in the Brazilian savanna

Directory of Open Access Journals (Sweden)

Tâmara Dias Oliveira Machado

Full Text Available BACKGROUND Knowledge on synanthropic phlebotomines and their natural infection by Leishmania is necessary for the identification of potential areas for leishmaniasis occurrence. OBJECTIVE To analyse the occurrence of Phlebotominae in gallery forests and household units (HUs in the city of Palmas and to determine the rate of natural infection by trypanosomatids. METHODS Gallery forests and adjacent household areas were sampled on July (dry season and November (rainy season in 2014. The total sampling effort was 960 HP light traps and eight Shannon traps. Trypanosomatids were detected in Phlebotominae females through the amplification of the SSU rDNA region, and the positive samples were used in ITS1-PCR. Trypanosomatid species were identified using sequencing. FINDINGS A total of 1,527 sand flies representing 30 species were captured in which 949 (28 spp. and 578 (22 spp. were registered in July and November, respectively. In July, more specimens were captured in the gallery forests than in the HUs, and Nyssomyia whitmani was particularly frequent. In November, most of the specimens were found in the HUs, and again, Ny. whitmani was the predominant species. Lutzomyia longipalpis was commonly found in domestic areas, while Bichromomyia flaviscutellata was most frequent in gallery forests. Molecular analysis of 154 pools of females (752 specimens identified Leishmania amazonensis, L. infantum, and Crithidia fasciculata in Ny. whitmani, as well as L. amazonensis in Lu. longipalpis, Trypanosoma sp. and L. amazonensis in Pintomyia christenseni, and L. amazonensis in both Psathyromyia hermanlenti and Evandromyia walkeri. MAIN CONCLUSIONS These results show the importance of gallery forests in maintaining Phlebotominae populations in the dry month, as well as their frequent occurrence in household units in the rainy month. This is the first study to identify Leishmania, Trypanosoma, and Crithidia species in Phlebotominae collected in Palmas, Tocantins

Chaco Chachalaca (Ortalis canicollis, Wagler, 1830 feeding ecology in a gallery forest in the South Pantanal (Brazil

Directory of Open Access Journals (Sweden)

J. Ragusa-Netto

Full Text Available Cracids are generalist frugivores, which often exploit plant food resources such as flowers and leaves, mainly when fruit production declines. The Chaco chachalaca (Ortalis canicollis is the most abundant cracid in the Pantanal (Brazil, and particularly common in the gallery forests. However, the factors related to their occurrence in this habitat type are unclear. In this study I describe the feeding habits and feeding niche breadth fluctuations of the Chaco chachalaca in relation to food resources abundance and diversity at the Miranda river gallery forest (Southern Pantanal. I also analyzed the relationships between Chaco chachalacas feeding activity and food resources abundance. This parameter (flowers and fruits exhibited significant seasonal differences of abundance in which flowers were plentiful at the end of the dry, while fruits were abundant during the early wet season. However, food resources diversity to Chaco chachalacas exhibited no seasonal difference. Their feeding activity paralleled the availability of food resources, so that when some items were massively available an enhanced number of Chaco chachalacas foraged in the gallery forest, particularly during the prolonged dry season when they extensively used flowers and Genipa americana fruits. In fact, the Chaco chachalaca feeding niche breadth value presented low values in this period, while high values were common in the rest of the year. The flexible diet of this cracid, potentially favors their year round presence in the gallery forest, mainly during the prolonged dry season when the propensity for famine might be high. Since the Chaco chachalaca is among the largest and most abundant canopy frugivores in the gallery forest, it may contribute to forest regeneration, an underscored role due to the impact of annual floods and meandering dynamics on tree loss.

The role of gallery forests in maintaining Phlebotominae populations: potential Leishmania spp. vectors in the Brazilian savanna.

Science.gov (United States)

Machado, Tâmara Dias Oliveira; Minuzzi-Souza, Thaís Tâmara Castro; Ferreira, Tauana de Sousa; Freire, Luciana Pereira; Timbó, Renata Velôzo; Vital, Tamires Emanuele; Nitz, Nadjar; Silva, Mariana Neiva; Santos, Alcinei de Souza; Sales, Nathyla Morgana Cunha; Obara, Marcos Takashi; Andrade, Andrey José de; Gurgel-Gonçalves, Rodrigo

2017-10-01

Knowledge on synanthropic phlebotomines and their natural infection by Leishmania is necessary for the identification of potential areas for leishmaniasis occurrence. To analyse the occurrence of Phlebotominae in gallery forests and household units (HUs) in the city of Palmas and to determine the rate of natural infection by trypanosomatids. Gallery forests and adjacent household areas were sampled on July (dry season) and November (rainy season) in 2014. The total sampling effort was 960 HP light traps and eight Shannon traps. Trypanosomatids were detected in Phlebotominae females through the amplification of the SSU rDNA region, and the positive samples were used in ITS1-PCR. Trypanosomatid species were identified using sequencing. A total of 1,527 sand flies representing 30 species were captured in which 949 (28 spp.) and 578 (22 spp.) were registered in July and November, respectively. In July, more specimens were captured in the gallery forests than in the HUs, and Nyssomyia whitmani was particularly frequent. In November, most of the specimens were found in the HUs, and again, Ny. whitmani was the predominant species. Lutzomyia longipalpis was commonly found in domestic areas, while Bichromomyia flaviscutellata was most frequent in gallery forests. Molecular analysis of 154 pools of females (752 specimens) identified Leishmania amazonensis, L. infantum, and Crithidia fasciculata in Ny. whitmani, as well as L. amazonensis in Lu. longipalpis, Trypanosoma sp. and L. amazonensis in Pintomyia christenseni, and L. amazonensis in both Psathyromyia hermanlenti and Evandromyia walkeri. These results show the importance of gallery forests in maintaining Phlebotominae populations in the dry month, as well as their frequent occurrence in household units in the rainy month. This is the first study to identify Leishmania, Trypanosoma, and Crithidia species in Phlebotominae collected in Palmas, Tocantins, Brazil.

Abundance and frugivory of the toco toucan (Ramphastos toco in a gallery forest in Brazil's Southern Pantanal

Directory of Open Access Journals (Sweden)

J. Ragusa-Netto

Full Text Available Unlike other toucan species, the Toco toucan (Ramphastos toco - the largest Ramphastidae - usually inhabits dry semi-open areas. This conspicuous canopy frugivore uses a large home range that includes a variety of vegetation types, among which gallery forests are widely cited as important to this species. However, the factors relating to the occurrence of Toco toucans in such habitats are unclear. I studied the abundance of Toco toucans as well as the availability of fleshy fruit in a gallery forest in the southern Pantanal (sub-region of Miranda, Brazil, in order to assess the relationship between these parameters. Also, I examined toucan foraging activity to analyze its relationship with both toucan abundance and fruit availability. The presence of the Toco toucan was more common in the gallery forest from the middle to the end of the dry season and during the middle of the wet season. Toucans foraged for fleshy fruits, mainly Genipa americana, Ficus luschnatiana, and Cecropia pachystachya fruits, feeding mostly on G. americana (by far the favorite food resource and F. luschnatiana fruits during the dry season, while C. pachystachya fruits were important in the wet season. Toco toucans foraged particularly heavily (> 80% of foraging activity on G. americana fruits during the latter part of the dry season, when fleshy fruit availability declined sharply. Toco toucan abundance in the gallery forest was associated with the availability of the most commonly consumed fleshy fruits, and also with its foraging activity. This finding suggests that the Toco toucan moved to the gallery forest periodically in response to the availability of abundant food resources, especially the G. americana fruits widely available and exploited during the severely dry season. Therefore, these fruits potentially contribute to Toco toucan persistence in the South Pantanal during the harshest period of the year.

Abundance and frugivory of the Toco toucan (Ramphastos toco) in a gallery forest in Brazil's southern Pantanal.

Science.gov (United States)

Ragusa-Netto, J

2006-02-01

Unlike other toucan species, the Toco toucan (Ramphastos toco)--the largest Ramphastidae--usually inhabits dry semi-open areas. This conspicuous canopy frugivore uses a large home range that includes a variety of vegetation types, among which gallery forests are widely cited as important to this species. However, the factors relating to the occurrence of Toco toucans in such habitats are unclear. I studied the abundance of Toco toucans as well as the availability of fleshy fruit in a gallery forest in the southern Pantanal (sub-region of Miranda, Brazil), in order to assess the relationship between these parameters. Also, I examined toucan foraging activity to analyze its relationship with both toucan abundance and fruit availability. The presence of the Toco toucan was more common in the gallery forest from the middle to the end of the dry season and during the middle of the wet season. Toucans foraged for fleshy fruits, mainly Genipa americana, Ficus luschnatiana, and Cecropia pachystachya fruits, feeding mostly on G. americana (by far the favorite food resource) and F. luschnatiana fruits during the dry season, while C. pachystachya fruits were important in the wet season. Toco toucans foraged particularly heavily (> 80% of foraging activity) on G. americana fruits during the latter part of the dry season, when fleshy fruit availability declined sharply. Toco toucan abundance in the gallery forest was associated with the availability of the most commonly consumed fleshy fruits, and also with its foraging activity. This finding suggests that the Toco toucan moved to the gallery forest periodically in response to the availability of abundant food resources, especially the G. americana fruits widely available and exploited during the severely dry season. Therefore, these fruits potentially contribute to Toco toucan persistence in the South Pantanal during the harshest period of the year.

Preparation of the PRACLAY demonstration and confirmation experiments: construction of the PRACLAY gallery

International Nuclear Information System (INIS)

Bastiaens, W.

2009-01-01

The PRACLAY demonstration and confirmation experiments contribute to the Belgian research, development and demonstration programme to assess the safety and feasibility of geological disposal of radioactive waste in Boom Clay. Within this programme, the large scale PRACLAY heater experiment aims to verify that Boom Clay is suitable to host heat emitting radioactive waste. A 35 m long section of an experimental gallery in the underground research facility HADES (at 225 m depth) will be heated up to 95 degrees Celsius during ten years. The heater experiment focuses on the response of the host rock to the thermal load. The figure below shows the experimental lay-out. In 2007, an important milestone was reached with the realisation of the PRACLAY gallery (45 m long, external diameter 2.5 m)

Natural regeneration in several environments of the Capetinga gallery forest at Agua Limpa Farm (DF

Directory of Open Access Journals (Sweden)

Jeanine Maria Felfili

2009-03-01

Full Text Available The Capetinga gallery forest is located at Agua Limpa Farm, in the Federal District, Brazil. The floristic compositionand structure of the natural regeneration at the edges and in the interior of the gallery forest at the watershed of the Capetinga stream was studied to detect floristic and structural patterns related to the forest environments. Thirty (5x5m plots were placed in each environment to sample saplings, individuals from 1,0m high with diameter at the steam base under 5,0cm. Within these plots, (2x2m sub-plots were allocated to sample seedlings, individuals lower than 1,0m height. The sampled plots were distant to the stream bank to minimize the humidity effect. Shannon & Wiener diversity index varied from 2,86 (seedlings at the edges to 3,51 (saplings at the interior and it was higher in the interior for both categories. Sørensen s similarity index varied from 0.474 for seedlings (comparingedges with interior to 0.735 (seedlings and saplings at the edges. Czekanowski indices were low and reflected the high differentiationin structure from plot to plot in the same gallery forest. TWINSPAN classification suggested two distinct communities for saplings forboth conditions, formed by species accordingly to their requirements for light and water. No differentiation was detected for seedlingsbetween the environments indicating a low response of plants at an early stage to the environmental conditions within the forest. TheCapetinga gallery forest suffered disturbances by fire and the small variations in species composition and vegetation structurebetween environments suggests that most of the natural regeneration is tolerant to light.

Competitive excitation and osmotic-pressure-mediated control of lasing modes in cholesteric liquid crystal microshells

Science.gov (United States)

Lin, Ya-Li; Gong, Ling-Li; Che, Kai-Jun; Li, Sen-Sen; Chu, Cheng-Xu; Cai, Zhi-Ping; Yang, Chaoyong James; Chen, Lu-Jian

2017-05-01

We examined the end-pumped lasing behaviors of dye doped cholesteric liquid crystal (DDCLC) microshells which were fabricated by glass capillary microfluidics. Several kinds of mode resonances, including distributed feedback, Fabry-Pérot (FP), and whispering gallery (WG) modes, can be robustly constructed in each individual DDCLC microshell by varying the beam diameter, namely, tuning the DDCLC gain area. The FP and WG modes were further confirmed experimentally, and the corresponding lasing mechanisms are clearly revealed from the unique material characteristics of DDCLC and the geometrical structure of the microshell. Additionally, we demonstrated that the osmotic pressure can be used to shrink/expand the microshell, productively tuning the excitation of lasing modes in a controlled manner. We wish our findings can provide a new insight into the design of DDCLC microlasers with tunable optical properties.

From the galleries to the clinic: applying art museum lessons to patient care.

Science.gov (United States)

Miller, Alexa; Grohe, Michelle; Khoshbin, Shahram; Katz, Joel T

2013-12-01

Increasingly, medical educators integrate art-viewing into curricular interventions that teach clinical observation-often with local art museum educators. How can cross-disciplinary collaborators explicitly connect the skills learned in the art museum with those used at the bedside? One approach is for educators to align their pedagogical approach using similar teaching methods in the separate contexts of the galleries and the clinic. We describe two linked pedagogical exercises--Visual Thinking Strategies (VTS) in the museum galleries and observation at the bedside--from "Training the Eye: Improving the Art of Physical Diagnosis," an elective museum-based course at Harvard Medical School. It is our opinion that while strategic interactions with the visual arts can improve skills, it is essential for students to apply them in a clinical context with faculty support-requiring educators across disciplines to learn from one another.

New numerical modelling of the mechanical long-term behaviour of the GMR gallery in ANDRA's Underground Research Laboratory

International Nuclear Information System (INIS)

Blanco Martin, L.; Hadj-Hassen, F.; Tijani, M.; Armand, G.

2011-01-01

This paper deals with a new macroscopic numerical modelling of the mechanical long-term behaviour of ANDRA's Underground Research Laboratory. The study focuses on the GMR gallery, oriented along the minor horizontal principal stress and located at the main level 490 m deep. The simulations are made using the finite element method (FEM).Convergence measurements in this gallery exhibit an important dis-symmetry between the vertical and horizontal directions, as well as a significant time effect in the vertical trend. In attempts to both understand the phenomena that lie beneath such dis-symmetry and reproduce the experimental data, a modification to Lemaitre's creep law has been proposed. The new viscoplastic law takes into account the following aspects: rock transverse isotropy, creep behaviour and rock expansion. The excavation history of the GMR gallery has also been considered in the numerical modelling. The numerical results are very satisfactory for the GMR drift. However, the mechanisms of anisotropic shear and expansion on which the new law is based do not lead to an accurate reproduction of the data measured in the galleries oriented in the perpendicular direction. Therefore, a thorough insight into the mechanical behaviour of the rock mass and into the proposed new law is needed before the latter can be applied to the Callovo-Oxfordian layer. (authors)

Continuum equivalent model for the fractured EDZ around underground galleries in clay-stone

International Nuclear Information System (INIS)

Pouya, A.; Bourgeois, E.; Larbi, B.; Poutrel, A.

2010-01-01

Document available in extended abstract form only. The Excavation Damaged Zone (EDZ) around the underground galleries excavated in clay-stone for the CMHM project, includes several zones showing different types of cracking and/or fracturing. In the vicinity of the wall, a fractured zone is observed that spreads out on a distance of about 1 m from the wall; at a larger distance from the wall one observes another zone with micro-cracks. The first zone, called 'fractured EDZ', includes different families of fractures with different geometries and origins. The main one consists of a family of shear fractures called 'chevron', that have approximately the shape of conical surfaces slightly flattened with respect to the horizontal plane. The 'chevrons' observed in the galleries at 490 m depth in LMSMH are regularly spaced of about 50 cm to 1 m along the gallery's axis, make an angle of about 45 deg. with this axis and extend to about 2 or 3 m beyond the wall depending of the size and orientation of the gallery. The fractures have a significant effect on the hydro-mechanical properties of the EDZ. The present work is focused on the effect of the 'chevron' fractures on the mechanical behaviour of the EDZ. Due to the large number of fractures, introducing them individually to the modelling leads to heavy and not easy to handle numerical models and to long calculations. One is led to find some Continuum Equivalent Material (CEM) for the EDZ including the fractures' effect. The EDZ is not very large compared to the fractures, so that it may not be fully justified to apply a homogenization approach; however, this is the approach we have used to define the behaviour of CEM. The geometry of the fractures is first simplified and assumed to correspond to conical surfaces with axial symmetry around the gallery's axis. The local behaviour of the CEM is deduced from the model of an infinite medium containing a family of planar

Technical feasibility of using gallery intakes for seawater RO facilities, northern Red Sea coast of Saudi Arabia: The King Abdullah Economic City site

KAUST Repository

Dehwah, Abdullah

2013-02-13

The Kingdom of Saudi Arabia is dependent on desalination of seawater to provide new water supplies for the future. Desalination is expensive and it is very important to reduce the cost and lower the energy consumption. Most seawater reverse osmosis facilities use open-ocean intakes, which require extensive pretreatment processes to remove particulate and biological materials that cause operating problems such as membrane fouling or shutdown during algal blooms. Subsurface systems, using the concept of riverbank filtration, can be used as intakes. These systems include wells of various designs and galleries that provide natural filtration and biological treatment to improve the quality of feed water before it enters the desalination plant. This reduces operating cost, lowers chemical and energy consumption, and reduces environmental impacts. Technical feasibility of gallery-type intakes, beach and seabed types, for use as intakes to seawater reverse osmosis (RO) facilities was evaluated along the northern Red Sea shoreline of Saudi Arabia. The geological characteristics of the offshore ocean bottom were found to be favorable for the development of seabed gallery systems, but the shoreline geology was not adequate for the development of beach gallery intakes. One of the potentially favorable sites for a seabed gallery system was located in the nearshore area at King Abdullah Economic City (KAEC). Detailed investigation of the site hydrology (tides and wave action), sediment grain size characteristics, and sediment hydraulic conductivity, and access for construction were assessed. It was determined that seabed gallery development is favorable at the site. Based on the seawater that has a salinity of about 41,000 mg/L and a conversion rate of 40%, a conservatively designed gallery cell with dimensions of 100 by 50 m would produce about 25,000 m3/day of filtered seawater and seven cells (6 primary and 1 standby) could support a 60,000 m3/day (permeate) seawater RO plant

Lifelong Learning for People Aged 64+ within the Contemporary Art Gallery Context

Science.gov (United States)

Goulding, Anna

2012-01-01

This paper reports the initial findings from Contemporary Visual Art and Identity Construction--Wellbeing Amongst Older People: a two-year research project that aims to understand how the lives of older people can be improved by examining their use of contemporary visual art in the art gallery and museum. It will focus on data relating to lifelong…

Artistic Sensibility in the Studio and Gallery Model: Revisiting Process and Product

Science.gov (United States)

Thompson, Geoffrey

2009-01-01

This paper examines the cultivation of artistic sensibility and its impact on the art therapy process and product in a community mental health center. Artistic sensibility embodies the sense of self as an artist through the integration of artistic and aesthetic attributes of self and other. The formation of a gallery to exhibit patient art was…

Experiences from a Real-Time Mobile Collaborative Writing System in an Art Gallery

DEFF Research Database (Denmark)

Korn, Matthias; Polli, Anna Maria; Klokmose, Clemens Nylandsted

as interfaces to the shared physical space. With a collocated collaborative writing system in the semi-public space of a gallery, we encourage local art discussions and provide a platform for the public to actively participate in interpretations of individual artworks. In this paper, we focus on the experiences...

The evaluation of radon concentration and working levels using SSNTD in the U-exploration galleries in the eastern desert, Egypt

International Nuclear Information System (INIS)

Abdel-hafez, A.I.; Eissa, H.M.; Abdel-Monem, A.A.; Abdel-Razek, Y.A.; El-Naggar, A.M.; El-fiki, S.A.

1996-01-01

Radon gas concentrations and the working levels (radon daughters concentrations) were measured using solid state nuclear track detectors (SSNTD) namely Cr-39, Mk, Lr 115 and CN 85, in three U-exploration galleries at Qattar-1, El Missikat, and El-Erediya areas, eastern desert, Egypt. In each U-exploration gallery 10 monitoring stations were chosen for measurements. The locations covered the differing intensities of the U-mineralization as well as ventilation conditions. Two sets of measurements were for the time intervals and 50 days). Calibration experiments on the SSNTD were performed using 238 Pu source (6.06/MeV), to find the optimum conditions for etching the detectors. The ranges of alpha track densities (t/mm 2 day) measured for Qattar-1 gallery are 23.7-46.6 (CR-39), 13.4-30.9 (MK), 11.1-22.9 (CN-85) and 8.8-15.4 (LR-115) for 27 day monitoring, whereas the ranges for the 50 days experiment are 8.8-25.8 (CR-39), 8.3-15.4 (MK) and 3.9-8.2 (LR-115). In el Missikat gallery, the alpha track densities ranges are 17.1-128.8 (CR-39), 11.4-73.1 (MK), 8.0-74.4 (CN.85) and 5.7-37.8 (LR-115) for the 27 day interval, whereas the ranges are (CR-39), 6.3-38.0 (MK) and 3.4-21.0 (LR-115) for the 50 days experiments. Alpha tracks densities for El-Erediya gallery ranges are 14.1-39.9 (CR-39), 8.9-20.0 (MK), 7.9-23.1 (CN-85), and 2.7-17.6 (LR-115) for the 27 days experiment. whereas the ranges are 8.5-22.7 (CR-39), 6.4-13.4 (MK), and 2.4-9.3 (LR-115)for the 50 days experiment. Working level measurements are compared with 1 W L equivalent to 16.28 tracks/ mm 2 day. Evaluation of the measurements at each monitoring station is discussed in terms of U-concentration and ventilation conditions. Also, the efficiency of the different SSNTD are discussed as well as the optimum time of monitoring at each U-exploration gallery. 4 figs., 5 tabs

The evaluation of radon concentration and working levels using SSNTD in the U-exploration galleries in the eastern desert, Egypt

Energy Technology Data Exchange (ETDEWEB)

Abdel-hafez, A I; Eissa, H M [National Institute of Measurement and Standards, Technology, Cairo (Egypt); Abdel-Monem, A A; Abdel-Razek, Y A; El-Naggar, A M [Nuclear Materials Authority, Cairo (Egypt); El-fiki, S A [Physicsics Dept., Faculty of Sciences, Ain Shams University. Cairo (Egypt)

1997-12-31

Radon gas concentrations and the working levels (radon daughters concentrations) were measured using solid state nuclear track detectors (SSNTD) namely Cr-39, Mk, Lr 115 and CN 85, in three U-exploration galleries at Qattar-1, El Missikat, and El-Erediya areas, eastern desert, Egypt. In each U-exploration gallery 10 monitoring stations were chosen for measurements. The locations covered the differing intensities of the U-mineralization as well as ventilation conditions. Two sets of measurements were for the time intervals and (50 days). Calibration experiments on the SSNTD were performed using {sup 238} Pu source (6.06/MeV), to find the optimum conditions for etching the detectors. The ranges of alpha track densities (t/mm{sup 2} day) measured for Qattar-1 gallery are 23.7-46.6 (CR-39), 13.4-30.9 (MK), 11.1-22.9 (CN-85) and 8.8-15.4 (LR-115) for 27 day monitoring, whereas the ranges for the 50 days experiment are 8.8-25.8 (CR-39), 8.3-15.4 (MK) and 3.9-8.2 (LR-115). In el Missikat gallery, the alpha track densities ranges are 17.1-128.8 (CR-39), 11.4-73.1 (MK), 8.0-74.4 (CN.85) and 5.7-37.8 (LR-115) for the 27 day interval, whereas the ranges are (CR-39), 6.3-38.0 (MK) and 3.4-21.0 (LR-115) for the 50 days experiments. Alpha tracks densities for El-Erediya gallery ranges are 14.1-39.9 (CR-39), 8.9-20.0 (MK), 7.9-23.1 (CN-85), and 2.7-17.6 (LR-115) for the 27 days experiment. whereas the ranges are 8.5-22.7 (CR-39), 6.4-13.4 (MK), and 2.4-9.3 (LR-115)for the 50 days experiment. Working level measurements are compared with 1 W L equivalent to 16.28 tracks/ mm{sup 2} day. Evaluation of the measurements at each monitoring station is discussed in terms of U-concentration and ventilation conditions. Also, the efficiency of the different SSNTD are discussed as well as the optimum time of monitoring at each U-exploration gallery. 4 figs., 5 tabs.

Fra Bartolomeo della Porta detto Fra Bartolomeo, Adorazione del Bambino, National Gallery, London

DEFF Research Database (Denmark)

Fischer, Chris

2014-01-01

En artikel om et maleri af Fra Bartolomeo i National Gallery i London udlånt til en udstilling i Museo Tosio Martinengo I Brescia i forbindelse med opdagelsen af et fuldstændigt overensstemmende maleri i dette museums magasiner. Hypotesen var at Bresciabilledet var et værkstedsarbejde lavet på ba...

Species composition and reproductive modes of anurans from a transitional Amazonian forest, Brazil

Directory of Open Access Journals (Sweden)

Youszef O. C. Bitar

2012-02-01

Full Text Available The aim of the present study was to describe the species composition and reproductive modes of an anuran community from a transition area between the Amazonia and Cerrado biomes. Data were collected in habitats exhibiting different degrees of anthropogenic degradation. The community (35 species identified during the present study presented a larger number of reproductive modes when compared with those from Cerrado communities, but smaller than those of other sites in the Amazon. While all nine modes were recorded in the gallery forests of local rivers and streams, anthropogenic habitats (rubber tree orchards and soybean fields were occupied only by species adapted to environments where humidity is low, typical of the Cerrado. Overall, the anuran fauna of the study area was characterized by species that depend on access to water bodies for their reproduction, with only a few specialized species able to reproduce in dry environments.

The Spiral Gallery: Non-Market Creativity and Belonging in an Australian Country Town

Science.gov (United States)

Waitt, Gordon; Gibson, Chris

2013-01-01

This paper seeks to explore creative practice in an Australian country town, and in so doing, to unsettle market-orientated interpretations of creativity that privilege the urban. Instead of focusing on creative practice as a means to develop industries, we focus on how creativity is a means to establish a cooperative gallery space that helps to…

Feasibility of Gallery Intake Systems for Seawater Reverse Osmosis Facilities along the Northern Red Sea Coast of Saudi Arabia

KAUST Repository

Dehwah, Abdullah

2012-03-01

The Kingdom of Saudi Arabia is dependent on desalination of seawater to provide new water supplies for the future. Desalination is expensive and it is very important to reduce the cost and lower the energy consumption. Most seawater reverse osmosis facilities use open-ocean intakes, which require extensive pre-treatment processes to remove particulate and biological materials that cause operating problems. An alternative intake is the subsurface system which utilizes the concept of riverbank filtration using wells or galleries and provides natural filtration to improve the quality of feedwater before it enters the desalination plant. This reduces operating cost and lowers energy consumption. Research was focused on evaluating gallery-type intakes (beach and seabed galleries) that could be used along the Northern Red Sea shoreline to provide a better quality feedwater for desalination. The geological characteristics of the visited sites were favorable for the development of seabed filter systems (offshore), but not for beach gallery intakes. The low wave energy along the shoreline and the presence of mud or rocky coasts made beach galleries infeasible. One of the potentially favorable sites for a seabed filter was located in the nearshore area at King Abdullah Economic City (KAEC). This site has a predominantly sandy offshore bottom with shallow water depths, and a low tide range. In addition, the bottom is always covered with water and contains soft limestone unit below the sand mantle that could be easy excavated to facilitate the construction of a seabed filter. About 50 sediment samples were collected from the site and laboratory measurements were performed on them. Grain size distribution, porosity and hydraulic conductivity measurements were performed on the sediment samples. In addition, six statistical methods were used to estimate the hydraulic conductivity values. Based on results of lab measurements, field observations, tide ranges and sediment types, it

Thermal simulation of drift emplacement. Geotechnical and geophysical investigations in and around backfilled galleries

International Nuclear Information System (INIS)

Schneefub, J.U.; Gommlich, G.E.

1988-01-01

The concept for the direct disposal of spent fuel in rock salt foresees the emplacement of large waste canisters on the floor of a disposal gallery. Subsequent to emplacement the drift is backfilled with salt grit. In a demonstration test six cylindrical containments are to be emplaced within distances of 3 m from each other in two parallel galleries of 14 m 2 , separated by a pillar of 10 m thickness. They will be heated up by a power output of approx. 1 kW/m to 200 degree C surface temperature by electrical heaters. The thermal and mechanical response of the salt rock and the backfilling to the artificial heating is to be investigated as follows: (1) measurement of the temperature field at the contained surface, in the backfill and in the rock salt; (2) deformation measurements of the salt rock around the heated drifts; (3) measurements of tunnel convergence in heated and unheated sections; (4) compaction measurements of the backfilling in heated and unheated areas; (5) measurement of rock stresses in areas very close to the galleries; and (6) pressure measurements in the backfilling, between backfilling and rock, and between backfilling and containers. The rock burst monitoring system of the Asse salt mine will be expanded to this special field of the mine to detect seismic events due to thermomechanical effects. Another seismoacoustic system will be installed to observe the compaction of the backfilling. This system must be calibrated for the relation between the density and velocities of seismic waves. It is planned to monitor the density by gamma-gamma log measurements. The changes in overall density during the entire experiment will be observed by gravimeter measurements of high precision

The Art Gallery Test: A Preliminary Comparison between Traditional Neuropsychological and Ecological VR-Based Tests

Directory of Open Access Journals (Sweden)

Pedro Gamito

2017-11-01

Full Text Available Ecological validity should be the cornerstone of any assessment of cognitive functioning. For this purpose, we have developed a preliminary study to test the Art Gallery Test (AGT as an alternative to traditional neuropsychological testing. The AGT involves three visual search subtests displayed in a virtual reality (VR art gallery, designed to assess visual attention within an ecologically valid setting. To evaluate the relation between AGT and standard neuropsychological assessment scales, data were collected on a normative sample of healthy adults (n = 30. The measures consisted of concurrent paper-and-pencil neuropsychological measures [Montreal Cognitive Assessment (MoCA, Frontal Assessment Battery (FAB, and Color Trails Test (CTT] along with the outcomes from the three subtests of the AGT. The results showed significant correlations between the AGT subtests describing different visual search exercises strategies with global and specific cognitive measures. Comparative visual search was associated with attention and cognitive flexibility (CTT; whereas visual searches involving pictograms correlated with global cognitive function (MoCA.

Victorian era esthetic and restorative dentistry: an advertising trade card gallery.

Science.gov (United States)

Croll, Theodore P; Swanson, Ben Z

2006-01-01

A chief means of print advertising in the Victorian era was the "trade card." Innumerable products, companies, and services were highlighted on colorful chromolithographic trade cards, and these became desirable collectible objects which were pasted into scrapbooks and enjoyed by many families. Dentistry- and oral health-related subjects were often depicted on Victorian trade cards, and esthetic and restorative dentistry themes were featured. This review describes the history of advertising trade cards and offers a photographic gallery of dentistry-related cards of the era.

Retention of external and internal markers by southern pine beetles (Coleoptera: Scolytidae) during gallery

Science.gov (United States)

Douglas J. Rhodes; Jane Leslie Hayes; Chris Steiner

1998-01-01

If retained, markers used in mark-release-recapture studies of bark beetle dispersal could provide valuable tools in the determination of post-dispersal fate. Retention of the internal marker rubidium (Rb) and of the external marker fluorescent powder during egg gallery construction, oviposition, and feeding were quantified at intervals from 0 to 96 hours by allowing...

License - Togo Picture Gallery | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available List Contact us Togo Picture Gallery License License to Use This Database Last updated : 2017/05/16 You may use this database...ecifies the license terms regarding the use of this database and the requirements you must follow in using this database.... The license for this database is specified in the Creative Commons ...Attribution 4.0 International . If you use data from this database, please be sure attribute this database a...e Creative Commons Attribution 4.0 International is found here . With regard to this database

Structural characterization of the gallery forest of the Guisa Agroforestry Experimental Station

Directory of Open Access Journals (Sweden)

José Luis Rodríguez Sosa

2018-01-01

Full Text Available The work was carried out in the gallery forest of the Cupaynicú stream, belonging to the Guisa Agroforestry Experimental Station, with the objective of characterizing its structure. Eight parcels of 500 m2 were randomly raised, in them the species were identified, their height and diameter were measured. The flora was analyzed through the origin of the species and the frequency histogram. The structure of the forest was analyzed through the diametric structure and the Value Index of Ecological Importance, the vertical structure was described taking into consideration the forest strata as well as the preparation of the canopy diagram. A descriptive analysis of the parameters diameter, height and basal area was made to study the parametric structure. The richness of the riparian forest was evidenced by the registry of 25 families, 40 genera and 43 species, as well as the predominance of the Meliaceae family followed by Lauraceae, Mimosaceae and Sapindaceae, which reflects the high timber value, melliferous and ecological of the same. The species Roystonea regia, Sterculiaapetala, Dendropanaxarboreus, Andirainermis and Mangifera indica, determine the physiognomy of the gallery Forest. The trees reach 33 cm in diameter and 18.27 m in height on average, although the presence of trees with 30 m is the most frequent, which denotes the irregular structure of the forest.

High frequency of trypanosomatids in gallery forest bats of a Neotropical savanna.

Science.gov (United States)

Lourenço, João Lucas M; Minuzzi-Souza, Thaís T C; Silva, Larissa R; Oliveira, Amanda C; Mendonça, Vagner J; Nitz, Nadjar; Aguiar, Ludmilla M S; Gurgel-Gonçalves, Rodrigo

2018-01-01

Bats are well-known hosts of trypanosomatids, though information about their role as reservoirs of these protozoans in the Brazilian savanna is poorly known. We aimed to analyze the occurrence of trypanosomatid species in bats occurring in remnants of gallery forests of Brasília, Federal District of Brazil. We sampled bats using mist nets in six sites, and we collected blood, wing fragments and oral swab samples from all captured individuals. Trypanosomatids were identified in the captured bats through sequencing of the SSUrRNA region and kDNA qPCR. We found no parasite in blood smears of 146 individuals of 14 species captured, but blood cultures were positive for nine bats. We detected trypanosomatids molecularly in 111 (76%) specimens of all bat species in the studied areas. Most of the infected bats had Leishmania-like DNA detected in blood and swab samples of the oral mucosa. We distinguished three species of Trypanosoma (Trypanosoma dionisii, T. rangeli and T. cruzi) in Carollia perspicillata. SSUrRNA PCR of oral samples is a non-invasive and practical method for identification of trypanosomatid species in bats. Our results support our belief that bats could be potential reservoirs for Trypanosoma and Leishmania-like species in the enzootic cycle of these parasites in gallery forests of the Brazilian Cerrado biome. Copyright © 2017 Elsevier B.V. All rights reserved.

Rael Artel Gallery: Non-Profit Project Space : short tale of an experimental project's space tactics / Kiwa

Index Scriptorium Estoniae

Kiwa, pseud., 1975-

2009-01-01

Aastatel 2004-2008 Pärnus ja aastatel 2006-2008 Tartus tegutsenud Rael Artel Galeriist, mille looja ja moderaator oli Rael Artel. Galerii tegevus lõppes kunstialbumi "Hotell Pärnu : Rael Arel Gallery : Non Profit Project Space 2004-2008 / kontseptsioon ja toimetamine: Rael Artel" ilmumisega 2009. aastal

Telerobotic Haptic Exploration in Art Galleries and Museums for Individuals with Visual Impairments.

Science.gov (United States)

Park, Chung Hyuk; Ryu, Eun-Seok; Howard, Ayanna M

2015-01-01

This paper presents a haptic telepresence system that enables visually impaired users to explore locations with rich visual observation such as art galleries and museums by using a telepresence robot, a RGB-D sensor (color and depth camera), and a haptic interface. The recent improvement on RGB-D sensors has enabled real-time access to 3D spatial information in the form of point clouds. However, the real-time representation of this data in the form of tangible haptic experience has not been challenged enough, especially in the case of telepresence for individuals with visual impairments. Thus, the proposed system addresses the real-time haptic exploration of remote 3D information through video encoding and real-time 3D haptic rendering of the remote real-world environment. This paper investigates two scenarios in haptic telepresence, i.e., mobile navigation and object exploration in a remote environment. Participants with and without visual impairments participated in our experiments based on the two scenarios, and the system performance was validated. In conclusion, the proposed framework provides a new methodology of haptic telepresence for individuals with visual impairments by providing an enhanced interactive experience where they can remotely access public places (art galleries and museums) with the aid of haptic modality and robotic telepresence.

Video gallery of educational lectures integrated in faculty's portal

Directory of Open Access Journals (Sweden)

Jaroslav Majerník

2013-05-01

Full Text Available This paper presents a web based educational video-clips exhibition created to share various archived lectures for medical students, health care professionals as well as for general public. The presentation of closely related topics was developed as video gallery and it is based solely on free or open source tools to be available for wide academic and/or non-commercial use. Even if the educational video records can be embedded in any websites, we preferred to use our faculty’s portal, which should be a central point to offer various multimedia educational materials. The system was integrated and tested to offer open access to infectology lectures that were captured and archived from live-streamed sessions and from videoconferences.

miRToolsGallery: a tag-based and rankable microRNA bioinformatics resources database portal

Science.gov (United States)

Chen, Liang; Heikkinen, Liisa; Wang, ChangLiang; Yang, Yang; Knott, K Emily

2018-01-01

Abstract Hundreds of bioinformatics tools have been developed for MicroRNA (miRNA) investigations including those used for identification, target prediction, structure and expression profile analysis. However, finding the correct tool for a specific application requires the tedious and laborious process of locating, downloading, testing and validating the appropriate tool from a group of nearly a thousand. In order to facilitate this process, we developed a novel database portal named miRToolsGallery. We constructed the portal by manually curating > 950 miRNA analysis tools and resources. In the portal, a query to locate the appropriate tool is expedited by being searchable, filterable and rankable. The ranking feature is vital to quickly identify and prioritize the more useful from the obscure tools. Tools are ranked via different criteria including the PageRank algorithm, date of publication, number of citations, average of votes and number of publications. miRToolsGallery provides links and data for the comprehensive collection of currently available miRNA tools with a ranking function which can be adjusted using different criteria according to specific requirements. Database URL: http://www.mirtoolsgallery.org PMID:29688355

Time-efficient CT colonography interpretation using an advanced image-gallery-based, computer-aided ''first-reader'' workflow for the detection of colorectal adenomas

International Nuclear Information System (INIS)

Mang, Thomas; Ringl, Helmut; Weber, Michael; Mueller-Mang, Christina; Hermosillo, Gerardo; Wolf, Matthias; Bogoni, Luca; Salganicoff, Marcos; Raykar, Vikas; Graser, Anno

2012-01-01

To assess the performance of an advanced ''first-reader'' workflow for computer-aided detection (CAD) of colorectal adenomas ≥ 6 mm at computed tomographic colonography (CTC) in a low-prevalence cohort. A total of 616 colonoscopy-validated CTC patient-datasets were retrospectively reviewed by a radiologist using a ''first-reader'' CAD workflow. CAD detections were presented as galleries of six automatically generated two-dimensional (2D) and three-dimensional (3D) images together with interactive 3D target views and 2D multiplanar views of the complete dataset. Each patient-dataset was interpreted by initially using CAD image-galleries followed by a fast 2D review to address unprompted colonic areas. Per-patient, per-polyp, and per-adenoma sensitivities were calculated for lesions ≥ 6 mm. Statistical testing employed Fisher's exact and McNemar tests. In 91/616 patients, 131 polyps (92 adenomas, 39 non-adenomas) ≥ 6 mm and two cancers were identified by reference standard. Using the CAD gallery-based first-reader workflow, the radiologist detected all adenomas ≥ 10 mm (34/34) and cancers. Per-patient and polyp sensitivities for lesions ≥ 6 mm were 84.3 % (75/89), and 83.2 % (109/131), respectively, with 89.1 % (57/64) and 85.9 % (79/92) for adenomas. Overall specificity was 95.6 % (504/527). Mean interpretation time was 3.1 min per patient. A CAD algorithm, applied in an image-gallery-based first-reader workflow, can substantially decrease reading times while enabling accurate detection of colorectal adenomas in a low-prevalence population. (orig.)

Silicon Photonics Cloud (SiCloud)

DEFF Research Database (Denmark)

DeVore, P. T. S.; Jiang, Y.; Lynch, M.

2015-01-01

Silicon Photonics Cloud (SiCloud.org) is the first silicon photonics interactive web tool. Here we report new features of this tool including mode propagation parameters and mode distribution galleries for user specified waveguide dimensions and wavelengths.......Silicon Photonics Cloud (SiCloud.org) is the first silicon photonics interactive web tool. Here we report new features of this tool including mode propagation parameters and mode distribution galleries for user specified waveguide dimensions and wavelengths....

Methodics of computing the results of monitoring the exploratory gallery

Directory of Open Access Journals (Sweden)

Krúpa Víazoslav

2000-09-01

Full Text Available At building site of motorway tunnel Višòové-Dubná skala , the priority is given to driving of exploration galley that secures in detail: geologic, engineering geology, hydrogeology and geotechnics research. This research is based on gathering information for a supposed use of the full profile driving machine that would drive the motorway tunnel. From a part of the exploration gallery which is driven by the TBM method, a fulfilling information is gathered about the parameters of the driving process , those are gathered by a computer monitoring system. The system is mounted on a driving machine. This monitoring system is based on the industrial computer PC 104. It records 4 basic values of the driving process: the electromotor performance of the driving machine Voest-Alpine ATB 35HA, the speed of driving advance, the rotation speed of the disintegrating head TBM and the total head pressure. The pressure force is evaluated from the pressure in the hydraulic cylinders of the machine. Out of these values, the strength of rock mass, the angle of inner friction, etc. are mathematically calculated. These values characterize rock mass properties as their changes. To define the effectivity of the driving process, the value of specific energy and the working ability of driving head is used. The article defines the methodics of computing the gathered monitoring information, that is prepared for the driving machine Voest – Alpine ATB 35H at the Institute of Geotechnics SAS. It describes the input forms (protocols of the developed method created by an EXCEL program and shows selected samples of the graphical elaboration of the first monitoring results obtained from exploratory gallery driving process in the Višòové – Dubná skala motorway tunnel.

The potential of Lemna gibba L. and Lemna minor L. to remove Cu, Pb, Zn, and As in gallery water in a mining area in Keban, Turkey.

Science.gov (United States)

Sasmaz, Merve; Arslan Topal, Emine Işıl; Obek, Erdal; Sasmaz, Ahmet

2015-11-01

This study was designed to investigate removal efficiencies of Cu, Pb, Zn, and As in gallery water in a mining area in Keban, Turkey by Lemna gibba L. and Lemna minor L. These plants were placed in the gallery water of Keban Pb-Zn ore deposits and adapted individually fed to the reactors. During the study period (8 days), the plant and water samples were collected daily and the temperature, pH, and electric conductivity of the gallery water were measured daily. The plants were washed, dried, and burned at 300 °C for 24 h in a drying oven. These ash and water samples were analyzed by ICP-MS to determine the amounts of Cu, Pb, Zn, and As. The Cu, Pb, Zn and As concentrations in the gallery water of the study area detected 67, 7.5, 7230, and 96 μg L(-1), respectively. According to the results, the obtained efficiencies in L. minor L. and L. gibba L. are: 87% at day 2 and 36% at day 3 for Cu; 1259% at day 2 and 1015% at day 2 for Pb; 628% at day 3 and 382% at day 3 for Zn; and 7070% at day 3 and 19,709% at day 2 for As, respectively. The present study revealed that both L. minor L. and L. gibba L. had very high potential to remove Cu, Pb, Zn, and As in gallery water contaminated by different ores. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Radiometric survey in the sites of Regional office in Fortaleza, research gallery and camp in Itataia, CE (Brazil)

International Nuclear Information System (INIS)

1982-02-01

The radiometric survey in Regional officer sites in Fortaleza, Brazil, research gallery and camp in Itataia is presented. The measurings to be done, the instrumentation used and results obtained are described as well as the conclusions and recommendations. (C.M.) [pt

Contemporary Adult Education Philosophies and Practices in Art Galleries and Museums in Canada and the UK

Science.gov (United States)

Clover, Darlene E.; Bell, Lorraine

2013-01-01

Public art galleries and museums have been mandated to become more relevant and useful to the lived experiences of the broad communities they claim to serve. Adult education has long been part of the work of these institutions, although historically the relationship has been uneasy, and they seldom feature in the adult education literature. To…

An Insurgent Curatorial Strategy: Using Dialogue and Collaboration to Create Meaning in Public Art Galleries and Museums

Science.gov (United States)

Marsden, Scott

2018-01-01

My insurgent curatorial strategy incorporates theory around dialogue and is used to develop a participatory and collaborative process that gives voice to those who are marginalised and/or disfranchised and are suppressed by dominant social narratives. My strategy demonstrates how art galleries and museums can function as sites for community…

Social Phenomenological Analysis as a Research Method in Art Education: Developing an Empirical Model for Understanding Gallery Talks

Science.gov (United States)

Hofmann, Fabian

2016-01-01

Social phenomenological analysis is presented as a research method to study gallery talks or guided tours in art museums. The research method is based on the philosophical considerations of Edmund Husserl and sociological/social science concepts put forward by Max Weber and Alfred Schuetz. Its starting point is the everyday lifeworld; the…

Identification of Natural Oscillation Modes for Purposes of Seismic Assessment and Monitoring of HPP Dams

Energy Technology Data Exchange (ETDEWEB)

Kuz’menko, A. P., E-mail: apkuzm@gmail.com; Saburov, S. V., E-mail: saburov58@yandex.ru [Russian Academy of Sciences, Computer Equipment Design Technology Institute, Siberian Branch (Russian Federation)

2016-07-15

The paper puts forward a method for processing data from detailed seismic assessments of HPP dams (dynamic tests). A detailed assessment (hundreds of observation points in dam galleries) is performed with consideration of operating dam equipment and the microseismic noise. It is shown that dynamic oscillation characteristics (natural oscillation frequencies and modes in the main dam axes, the velocities of propagation of elastic waves with given polarization, and so on.) can be determined with sufficient accuracy by using complex transfer functions and pulse characteristics. Monitoring data is processed using data from a detailed assessment, taking account of identified natural oscillation modes and determined ranges of natural frequencies. The spectra of characteristic frequencies thus obtained are used to choose substitution models and estimate the elastic characteristics of the “dam – rock bed” construction system, viz., the modulus of elasticity (the Young modulus), the Poisson ratio, the dam section stiffness with respect to shear, tension and compression and the elastic characteristics of the rock foundation.

Lesbian identity and the politics of representation in Betty Parsons's gallery.

Science.gov (United States)

Gibson, A

1994-01-01

Although Betty Parsons had been unusually open about her love relationships with women in the twenties and thirties, she later became reticent, retiring to the closet. Her increased discretion after World War II, during the Cold War, coincided with her rise as the art dealer most prominently associated with the international emergence of Abstract Expressionism. Parsons incurred the objections of her Abstract Expressionists, however, by showing artists who included both abstraction and naturalism in their work, such as Sonia Sekula, Forrest Bess, and Hedda Sterne. This article examines her definition of abstraction as difference through her friend Theodoros Stamos's notion of camp and helps to explain her admiration of Barnett Newman despite her refusal to devote her gallery exclusively to his narrower version of significant abstraction.

Crafting glass vessels: current research on the ancient glass collections in the Freer Gallery of Art, Washington, D.C.

Science.gov (United States)

Nagel, Alexander; McCarthy, Blythe; Bowe, Stacy

Our knowledge of glass production in ancient Egypt has been well augmented by the publication of recently excavated materials and glass workshops, but also by more recent materials analysis, and experiments of modern glass-makers attempting to reconstruct the production process of thin-walled coreformed glass vessels. From the mounting of a prefabricated core to the final glass product our understanding of this profession has much improved. The small but well preserved glass collection of the Freer Gallery of Art in Washington, D.C. is a valid tool for examining and studying the technology and production of ancient Egyptian core formed glass vessels. Charles Lang Freer (1854-1919) acquired most of the material from Giovanni Dattari in Cairo in 1909. Previously the glass had received only limited discussion, suggesting that most of these vessels were produced in the 18th Dynasty in the 15th and 14th centuries BCE, while others date from the Hellenistic period and later. In an ongoing project we conducted computed radiography in conjunction with qualitative x-ray fluorescence analysis on a selected group of vessels to understand further aspects of the ancient production process. This paper will provide an overview of our recent research and present our data-gathering process and preliminary results. How can the examinations of core formed glass vessels in the Freer Gallery contribute to our understanding of ancient glass production and technology? By focusing on new ways of looking at old assumptions using the Freer Gallery glass collections, we hope to increase understanding of the challenges of the production process of core-vessel technology as represented by these vessels.

Monitoring the Excavation Damaged Zone in Opalinus clay by three dimensional reconstruction of the electrical resistivity in the Mont Terri gallery G-04

Science.gov (United States)

Lesparre, N.; Adler, A.; Nicollin, F.; Gibert, D.; Nussbaum, C.

2012-04-01

The characteristics of opalinus clay have been studied in the last years for its capacity to retain radionuclide transport as a low permeable rock. This formation presents thereby suitable properties for hosting repository sites of radioactive waste. The Mont Terri underground rock laboratory (Switzerland) has been excavated in opalinus clay layer in order to develop experiences improving the knowledge on the physico-chemical properties of the rock. The study of electrical properties furnishes information on the rock structure, its anisotropy and the changes of these properties with time (Nicollin et al., 2010 ; Thovert et al., 2011). Here the three dimensional reconstruction of the electrical resistivity aims at monitoring the temporal evolution of the excavation damaged zone. Three rings of electrodes have been set-up around the gallery and voltage is measured between two electrodes while a current is injected between two others (Gibert et al., 2006). Measurements have been achieved from July 2004 until April 2008 before, during and after the excavation of the gallery 04. In this study we develop a computational approach to reconstruct three dimensional images of the resistivity in the vicinity of the electrodes. A finite element model is used to represent the complex geometry of the gallery. The measurements inferred from a given resistivity distribution are estimated using the software EIDORS (Adler and Lionheart, 2006), this constitutes the forward problem. The reconstruction of the media resistivity is then implemented by fitting the estimated to the measured data, via the resolution of an inverse problem. The parameters of this inverse problem are defined by mapping the forward problem elements into a coarser mesh. This allows to reduce drastically the number of unknowns and so increases the robustness of the inversion. The inversion is executed with the conjugate gradient method regularised by an analysis of the Jacobian singular values. The results show an

Australian doctors and the visual arts. Part 2. Doctors as collectors, donors, gallery supporters and writers in New South Wales.

Science.gov (United States)

Hamilton, D G

1986-04-28

The contribution of doctors to the visual arts if being discussed in a series of six articles. The first article dealt with doctor-artists in new South Wales. In this, the second, doctors are discussed as collectors, donors, gallery supporters and writers in this State.

THE BOSS EMISSION-LINE LENS SURVEY. IV. SMOOTH LENS MODELS FOR THE BELLS GALLERY SAMPLE

Energy Technology Data Exchange (ETDEWEB)

Shu, Yiping [National Astronomical Observatories, Chinese Academy of Sciences, 20A Datun Road, Chaoyang District, Beijing 100012 (China); Bolton, Adam S.; Montero-Dorta, Antonio D.; Cornachione, Matthew A.; Zheng, Zheng; Brownstein, Joel R. [Department of Physics and Astronomy, University of Utah, 115 South 1400 East, Salt Lake City, UT 84112 (United States); Mao, Shude [Physics Department and Tsinghua Centre for Astrophysics, Tsinghua University, Beijing 100084 (China); Kochanek, Christopher S. [Department of Astronomy and Center for Cosmology and Astroparticle Physics, Ohio State University, Columbus, OH 43210 (United States); Pérez-Fournon, Ismael; Marques-Chaves, Rui [Instituto de Astrofísica de Canarias, C/Vía Láctea, s/n, E-38205 San Cristóbal de La Laguna, Tenerife (Spain); Oguri, Masamune [Research Center for the Early Universe, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Ménard, Brice, E-mail: yiping.shu@nao.cas.cn [Department of Physics and Astronomy, Johns Hopkins University, Baltimore, MD 21218 (United States)

2016-12-20

We present Hubble Space Telescope F606W-band imaging observations of 21 galaxy-Ly α emitter lens candidates in the Baryon Oscillation Spectroscopic Survey Emission-Line Lens Survey (BELLS) for the GALaxy-Ly α EmitteR sYstems (BELLS GALLERY) survey. Seventeen systems are confirmed to be definite lenses with unambiguous evidence of multiple imaging. The lenses are primarily massive early-type galaxies (ETGs) at redshifts of approximately 0.55, while the lensed sources are Ly α emitters (LAEs) at redshifts from two to three. Although most of the lens systems are well fit by smooth lens models consisting of singular isothermal ellipsoids in an external shear field, a thorough exploration of dark substructures in the lens galaxies is required. The Einstein radii of the BELLS GALLERY lenses are, on average, 60% larger than those of the BELLS lenses because of the much higher source redshifts. This will allow for a detailed investigation of the radius evolution of the mass profile in ETGs. With the aid of the average ∼13× lensing magnification, the LAEs are frequently resolved into individual star-forming knots with a wide range of properties. They have characteristic sizes from less than 100 pc to several kiloparsecs, rest-frame far-UV apparent AB magnitudes from 29.6 to 24.2, and typical projected separations of 500 pc to 2 kpc.

Post-occupancy evaluation of a restored industrial building: A contemporary art and design gallery in Mexico

Directory of Open Access Journals (Sweden)

J. Mundo-Hernández

2015-12-01

Full Text Available This paper presents the results obtained from a post-occupancy evaluation (POE study conducted in an old fabric building called “La Violeta”. This structure has been recently converted into a contemporary art gallery. La Violeta is located in Puebla City, Mexico. The building dates from the beginning of the 19th century; it was built and used as a textile factory until the first decades of the 20th century. This POE study aims to assess the new use of the building from the users׳ point of view. Methodology involves historical research of the building, analysis of the conversion strategy, walkthrough investigation, and a user survey. Questions regarding the re-utilization strategy used in the building and its current use are included in the survey, such as “How do people perceive the space regarding its functionality, accessibility, and comfort?” Although the re-utilization process destroyed several historic elements, the re-use of old industrial spaces that otherwise would be obsolete and disused seems pertinent. Developing small renovation projects as part of an integral and wider project seems feasible. Users perceive the building as comfortable but not properly advertised as an art gallery, and its location is difficult to find.

Adult Education for Social and Environmental Change in Contemporary Public Art Galleries and Museums in Canada, Scotland and England

Science.gov (United States)

Clover, Darlene E.

2015-01-01

Historically, pubic art galleries and museums have a well-deserved reputation for elitism, colonialism and exclusion and they are, therefore, frequently omitted from the discourse of adult education. However, the escalating social, cultural and ecological problems of this new century have placed pressure on these public institutions to change and…

Use of beach galleries as an intake for future seawater desalination facilities in Florida and globally similar areas

KAUST Repository

Missimer, Thomas M.

2013-06-17

Desalination of seawater using the reverse osmosis process can be made less costly by the use of subsurface intake systems. Use of conventional open-ocean intakes requires the addition of a number of pretreatment processes to protect the primary RO process. Despite using the best designs possible for the pretreatment, seawater RO membranes tend to biofoul because of the naturally-occurring organic material and small bacteria present in seawater. These materials are not completely removed by the pretreatment system and they pass through the cartridge filters into the membranes, thereby causing frequent and expensive cleaning of the membranes. Quality of the raw water can be greatly improved by the use of subsurface intakes which can substantially reduce the overall treatment cost. There are a number of possible subsurface designs that can be used including conventional vertical wells, horizontal wells, collector wells, beach galleries, and seabed filters. The key selection criteria for the type of subsurface intake most suited and most cost-effective for a site are based on the required volume of raw water and the local geology. The active shorelines of Florida are very well-suited for the development of beach gallery intake systems. These systems are installed beneath the active beach between the high and low tide zones of the beach. Since they are constructed with a depth to the screens between 3 and 5 m, they cannot be observed at surface and persons using the beach would be unaware of their existence. These galleries are simple to construct and they tend not to clog because the active wave action within the intertidal zone provides mechanical energy that continuously cleans the filter face. They also have other advantages, including: the water quality is seawater unaffected by substances present in freshwater aquifers occurring landward of the shoreline, the salinity of the water is generally constant, and there are no impacts on water users located inland from

Technical feasibility of a seabed gallery seawater intake at Ras Abu Ali Island, Arabian Gulf, Saudi Arabia

KAUST Repository

Rachman, Rinaldi

2014-07-23

(less than 1%) with porosity ranging between 0.29 and 0.41 and hydraulic conductivities up to 22.5 m3/d. It was determined that seabed gallery development is suitable at this location. Preliminary design for a seabed gallery filter was developed using a series of cells. Each gallery cell represents a unit that can be simply duplicated to meet the overall intake capacity requirement. Each gallery cell is designed to have minimum 8 m/d infiltration rate through five layers of engineered sand and gravel. The total thickness of the filter bed is 4.5 m (2 m top layer). The dimensions of the proposed cells are 100 × 30 m and each cell will conservatively provide 24,000 m3/d of filtered water. The design is flexible to meet the required capacity. For example, a SWRO desalination plant which produces 54,000 m3/d product water from 38,000 mg/L salinity seawater at a 45% conversion rate will require a minimum of 6 cells using the preliminary design. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

Technical feasibility of a seabed gallery system for SWRO facilities at Shoaiba, Saudi Arabia, and regions with similar geology

KAUST Repository

Rodri­guez, Luis R. Lujan

2013-09-02

Subsurface intakes can be used as part of the pretreatment system for seawater reverse osmosis facilities. Wells of various designs and galleries are being used for intakes at many sites globally to reduce pretreatment costs, chemical usage, biofouling potential, and environmental impacts (entrainment and impingement). The goal of using a subsurface intake is to reduce or replace conventional pretreatment processes. A field and laboratory investigation was undertaken to assess the feasibility of developing a seabed gallery intake offshore near the Shoaiba seawater RO (SWRO) plant site (150,000 m3/d treatment capacity) that could be used to replace the current intake used for only the RO capacity. A survey of the beach and offshore area was made and 51 sediment samples were collected from the seabed for laboratory analysis of grain size distribution, porosity, and hydraulic conductivity. Field observations showed that the marine bottom has a low slope from the shoreline seaward a distance of about 100 m to a depth of about 1.0 m before it steepens to a depth of over 2 m at 150 m from shore. The site has a relativity thin cover of unlithified carbonate sands, 2-5 cm thick, sitting on a soft coralline limestone of Pleistocene age. The sediments investigated were found to be clean carbonate or slightly muddy carbonate sands with mean grain diameters ranging mostly between 0.25 and 0.5 mm. Most of the area investigated contained a mud percentage between 0 and 5%. The measured porosity values range between 0.33 and 0.45 and measured hydraulic conductivity values from about 1.6 to 79.5 m/d with 64.6 m/d being the maximum offshore value. A preliminary design was developed to meet the full operational capacity of the Shoaiba SWRO treatment plant which would require 375,000 m3/d of raw water to produce 150,000 m3/d of permeate (40% conversion assumed for Red Sea water with a TDS of 41,000 mg/L). The design of the RO plant uses 10 trains to produce the 150,000 m3/d of product

Discovery of iron group impurity ion spin states in single crystal Y{sub 2}SiO{sub 5} with strong coupling to whispering gallery photons

Energy Technology Data Exchange (ETDEWEB)

Goryachev, Maxim; Farr, Warrick G.; Carmo Carvalho, Natalia do; Creedon, Daniel L.; Le Floch, Jean-Michel [ARC Centre of Excellence for Engineered Quantum Systems, University of Western Australia, 35 Stirling Highway, Crawley WA 6009 (Australia); Probst, Sebastian [Physikalisches Institut, Karlsruhe Institute of Technology, D-76128 Karlsruhe (Germany); Bushev, Pavel [Experimentalphysik, Universität des Saarlandes, D-66123 Saarbrücken (Germany); Tobar, Michael E., E-mail: michael.tobar@uwa.edu.au [ARC Centre of Excellence for Engineered Quantum Systems, School of Physics, University of Western Australia, Crawley 6009 (Australia)

2015-06-08

Interaction of Whispering Gallery Modes (WGMs) with dilute spin ensembles in solids is an interesting paradigm of Hybrid Quantum Systems potentially beneficial for Quantum Signal Processing applications. Unexpected ion transitions are measured in single crystal Y{sub 2}SiO{sub 5} using WGM spectroscopy with large Zero Field Splittings at 14.7 GHz, 18.4 GHz, and 25.4 GHz, which also feature considerable anisotropy of the g-tensors as well as two inequivalent lattice sites, indicating spins from Iron Group Ion (IGI) impurities. The comparison of undoped and Rare-Earth doped crystals reveal that the IGIs are introduced during co-doping of Eu{sup 3+} or Er{sup 3+} with concentration at much lower levels of order 100 ppb. The strong coupling regime between an ensemble of IGI spins and WGM photons have been demonstrated at 18.4 GHz and near zero field. This approach together with useful optical properties of these ions opens avenues for “spins-in-solids” Quantum Electrodynamics.

Wheatstone bridge-giant magnetoresistance (GMR) sensors based on Co/Cu multilayers for bio-detection applications

Science.gov (United States)

Antarnusa, G.; Elda Swastika, P.; Suharyadi, E.

2018-04-01

has potential application to be used in bio-detection applications where ultra-small bio-labels are needed.

In situ stress measurements at 250m gallery off the ventilation shaft

International Nuclear Information System (INIS)

Nakamura, Takahiro; Sanada, Hiroyuki; Sugita, Yutaka; Kato, Harumi

2011-06-01

From FY2000 to FY2005, JAEA had been making research at ground surface of Horonobe town for repository of high-level radioactive waste. During this period, geological investigation, hydrogeology investigation, rock mechanics investigation, geochemical investigation using boreholes were carried out in Hokushin area which is about 3kmx3km in surface area of Horonobe town in order to construct a geological environment model and to confirm the methodology for safety assessment. Now the research program proceeds to the next stage where the underground drifts and shafts are under construction. In the underground rock mass, in situ stress is the sum of tectonic stress as well as overlying stress due to gravity. In situ stresses enter into excavation design and are required in order to predict the response of rock masses to the disturbance associated with those structures. For these reasons, JAEA has carried out in situ stress measurements using vertical boreholes drilled from ground surface to evaluate the state of horizontal stress in the area. In the research during the underground construction, comparison between the stress measurements carried out at surface and at underground is conducted. And if inconsistency between these two measurements is found, the state of stress will be updated based on more reliable information. In order to study the 3D in situ state of stress around Horonobe Underground Research Laboratory, hydraulic fracturing tests and stress relief method (Conical-ended borehole method) were conducted at the 250m gallery located near the bottom of the ventilation shaft. Three 20.0m long boreholes, 09-V250-M01(slightly upwards), 09-V250-M02(slightly upwards) and 09-V250-M03(vertical), were drilled from the gallery using 76mm diameter bit. The results of the measurements are summarized as follows: (1) Hydraulic fracturing technique. Hydraulic fracturing technique using the test equipment with sufficiently small compliance was carried out in the three

Technical feasibility of using gallery intakes for seawater RO facilities, northern Red Sea coast of Saudi Arabia: The King Abdullah Economic City site

KAUST Repository

Dehwah, Abdullah; Missimer, Thomas M.

2013-01-01

intakes. One of the potentially favorable sites for a seabed gallery system was located in the nearshore area at King Abdullah Economic City (KAEC). Detailed investigation of the site hydrology (tides and wave action), sediment grain size characteristics

Passion Trumps Pay: A Study of the Future Skills Requirements of Information Professionals in Galleries, Libraries, Archives and Museums in Australia

Science.gov (United States)

Howard, Katherine; Partridge, Helen; Hughes, Hilary; Oliver, Gillian

2016-01-01

Introduction: This paper explores the current and future skills and knowledge requirements of contemporary information professionals in a converged gallery, library, archive and museum sector (also referred to as the GLAM sector) in Australia. This research forms part of a larger study that investigated the education needs of information…

Preliminary study of infiltration gallery for water treatment towards Universal Access 2019 in Indonesia

Directory of Open Access Journals (Sweden)

Maritha Nilam Kusuma

2018-06-01

Full Text Available Infiltration gallery is a method of water treatment through soil filtration. The mechanism is the filtering or absorption of contaminants in the river that flows through the soil. This method uses soil to remove contaminants. This method has three kinds of screening processes, ie physically, chemically and biologically. This process depends on moisture content, temperature, porosity, specific gravity, the saturated degree and hydraulic conductivity in the soil. Now a days, the cost of clean water production in the province of East Java, Indonesia requires a lot of cost, because the consumption of coagulant is very high; It is necessary to have a preliminary processing that helps the performance of water treatment in East Java, Indonesia. Natural water purification method using soil called infiltration gallery can be one solution in processing river water or as preliminary processing for water treatment in East Java. The purpose of this research is to know soil characteristics in soil samples in each region and its ability to removel TSS and Total Coliform. The second objective is to find good soil composition for removel TSS and total Coliform. The location of soil sampling is in Surabaya, Lumajang, Bangkalan, Mojokerto, Sidoarjo and Gresik, East Java province, Indonesia. The method of analysis used gravimetry, method 9223 B, the comparison between mass and specific gravity, constant head permeameter and wet grain. The results showed that the soil samples from each region were not able to remove the TSS and total coliform, so that the engineering of soil composition was required. Appropriate soil composition is sand and clay, 85% and 15%, with the percentage of TSS and total coliform removal of 63.50% and 99.67%.

Electrical tomography monitoring of the EDZ during the excavation of the gallery Ga08 in the Mont Terri URL

International Nuclear Information System (INIS)

Nicollin, Florence; Gibert, Dominique; Lesparre, Nolwenn; Nussbaum, Christophe

2010-01-01

Document available in extended abstract form only. In the Mont Terri Underground Rock Laboratory, the excavation of the new gallery Ga08 provided a unique opportunity to monitor the excavation damaged zone (EDZ) in the Opalinus clay, at time scales ranging from hours to months. The excavation of the gallery Ga08 has started from the northern end of the URL and has progressed towards the South, ending by the junction with the end of the gallery Ga04. Several geophysical and geochemical methods were performed from the end face of the gallery Ga04, to observe the evolution of the rock mass located in the so-called EZ-G08 section during the progress of the excavation. Thus, electrical resistivity measurements were performed, with electrodes placed both on the Ga04 face and in boreholes perpendicular to the face. These experiments revealed a strong anisotropy of the electrical resistivity of the rock mass, and they allowed to study the temporal evolution of the electrical resistivity in the EDZ. An array of more than 700 electrodes was installed on the rough face according to a square mesh with a mean side of 30 cm. On each line of the mesh, the electrodes were equally spaced every 15 cm. 4 horizontal boreholes, 8 m long and 56 mm in diameter, were equipped with lines of 64 electrodes equally spaced every 5 cm. Finally, 2 groups of 4 boreholes, 1 m long and spaced about 20 cm, were equipped with lines of 16 electrodes equally spaced every 5 cm. Using the electrode array of the face, Wenner profiles were acquired along both the horizontal and the vertical lines, highlighting a strong anisotropy of electrical resistivity since the values depend on the direction in which they are measured. In order to characterize this anisotropy, other measurements were done using the array of the face and the lines of the short boreholes, with the so-called square array configuration where the electrodes are located at the corners of squares with different orientations. On the face

Abundance and frugivory of the toco toucan (Ramphastos toco) in a gallery forest in Brazil's Southern Pantanal

OpenAIRE

Ragusa-Netto,J.

2006-01-01

Unlike other toucan species, the Toco toucan (Ramphastos toco) - the largest Ramphastidae - usually inhabits dry semi-open areas. This conspicuous canopy frugivore uses a large home range that includes a variety of vegetation types, among which gallery forests are widely cited as important to this species. However, the factors relating to the occurrence of Toco toucans in such habitats are unclear. I studied the abundance of Toco toucans as well as the availability of fleshy fruit in a galler...

Changing Subjects: The Gallery at Cleveland House and the Highland Clearances

Directory of Open Access Journals (Sweden)

Anne Nellis Richter

2016-04-01

Full Text Available In 1812, a porter named William Cantrill published a small volume of etchings dedicated to his employer, the Marchioness of Stafford. Cantrill characterized his reproductions of a select group of small Netherlandish pictures from the art gallery at the Marchioness’s London residence, Cleveland House, as “first attempts from an untutored hand”, calling attention to his status as a servant and untrained artist. In this article, I examine this idiosyncratic volume in light of the reception of small subject pictures in the early nineteenth century, and also within the context of the Marchioness of Stafford’s involvement in the Highland Clearances. At a moment when the Marchioness and her husband were under scrutiny for the heavy-handed tactics used against their Scottish tenants, this book used the category of genre painting to smooth over the gaps between landowner and tenant that the Clearances had made evident.

Floristic survey of the herbaceous-shrub layer of a gallery forest in Alto Paraíso de Goiás - GO, Brazil

Directory of Open Access Journals (Sweden)

Eduardo Chaves

2012-10-01

Full Text Available Flowering species of the herbaceous and shrubby layer were sampled in a gallery forest at Portal da Chapada, Alto Paraíso de Goiás-GO in the Chapada dos Veadeiros during 12 months growing within 4.5 meters on either side of a raised pathway 2.4 Km long. The collections were included to University of Brasilia Herbarium (UB. A total of 138 species (103 genera and 40 families were recorded; the most species-rich families were Asteraceae (22, Poaceae (14, Rubiaceae (12, Fabaceae (11 and Melastomataceae (7. The richest family in number of genera was Asteraceae (19, followed by Poaceae (8, Fabaceae (8 and Rubiaceae (7. The results showed a meaningful increase in the Chapada dos Veadeiros flora, especially considering the herbaceous-shrubby layer of the gallery forests (223.6%. Despite the richness of the flora, the number of endemics species in the Goiás State was only 1.5%.

Theoretical examination of the slot channel waveguide configured in a cylindrically symmetric dielectric ring profile

Science.gov (United States)

Gauthier, Robert C.; Alzahrani, Mohammed A.; Jafari, Seyed Hamed

2014-10-01

It has recently been experimentally demonstrated that slot channel waveguides, configured in cylindrical space, can support high azimuthal order modes similar to whispering-gallery modes. This paper presents a mode solver based on Maxwell's vector wave equation for the electric field cast into an eigenvalue problem using a Fourier-Bessel basis function space. The modal frequencies and field profiles of the high azimuthal order slot-channel-whispering-gallery (SCWG) modes are computed for a set of nanometer spaced silicon rings supported by oxide. The computations show, that in addition to the traditionally observed, lowest order mode, the structure may support higher order SCWG modes. We complete the analysis by computing structures response as an ambient medium index of refraction sensor which achieves over 400 nm per RIU sensitivity.

Convergence in anisotropic conditions: gallery behaviour in the Callovo-Oxfordian clayey layer in North-Eastern France

International Nuclear Information System (INIS)

Blanco Martin, L.; Hadj-Hassen, F.; Philippe, J.C.; Boidy, E.; Colombet, G.; Armand, G.

2010-01-01

Document available in extended abstract form only. Coyne et Bellier (Tractebel Engineering) has been supplying geotechnical services to Andra since 1994 regarding the feasibility for developing a repository for radioactive waste in a 490 m deep clayey formation at the Meuse/Haute-Marne site. Armines/Mines-ParisTech (French engineering school) has been an Andra scientific partner for several years due to its expertise in rock creep behaviour as well as in mining technologies. Throughout the different works carried out for Andra (especially the studies concerning the enlargement of the underground research laboratory), the behaviour of the Callovo-Oxfordian clayey were computed. These studies are used mainly for predicting the long-term behaviour of this layer. Lemaitre's rheological law (or modified Norton's law) has been used for such purposes. This time-dependent law is able to model the isotropic hardening of an elastic-viscoplastic solid by taking into account a non linear viscosity (γ) which Coyne et Bellier has decided to represent by means of a cone-shaped dash-pot element (stiffness increases during creep, cf. Eric Boidy's PhD). This hypothesis, together with that standing for 'long-term incompressibility' (viscoplastic deformation occurs at constant volume), allows the law be expressed by means of the second invariants of the stress (q) and strain (ε vp ) tensors. The rheological model when the long term behaviour takes place beyond a stress threshold (σ S ) is shown. Modelling works that use this law reproduce well convergence measurements as long as radial stresses around the galleries are isotropic. When the stress field around the gallery is anisotropic, the classic Lemaitre's law no longer fits the convergence measurements. This is the case for the GMR gallery at the main level of the laboratory: the horizontal stress is 1.3 times greater than the vertical stress whilst the average vertical convergence is more than five

Tikutõmbeid kottpimedas galeriis = Striking matches in a pitch-dark gallery : [luuletused] / Artur Alliksaar

Index Scriptorium Estoniae

Alliksaar, Artur, 1923-1966

2001-01-01

Tekst eesti ja inglise k. A. Alliksaare lühibiograafia eesti ja inglise k. lk. 55. Sisu: Tikutõmbeid kottpimedas galeriis = Striking matches in a pitch-dark gallery ; "Olen määratusuur mets..." = "I am infinitely vast forest..." ; "Olen koredate külgedega kalju..." = "I am rough-sided cliff..." ; "Olen meri, millel puudub äär..." = "I am sea that knows no bounds..." ; "Liikumine on niivõrd liitunud mu loomusega..." = "Movement is so much part of me..." ; "Ma ei söandaks öelda, et olen rikas..." = "I would not claim that I am rich..." ; Pöördehetk = Turning point ; Kuigi on nii palju lilli... = Though there are so many flowers ; Antidolorosum

Electrical resistivity imaging survey to detect uncharted mine galleries in the mining district of Linares, Jaén, Spain

Science.gov (United States)

Martínez-López, J.; Rey, J.; Dueñas, J.; Hidalgo, C.; Benavente, J.

2012-02-01

The scarcity of information about the existence of old mining shafts and galleries in urban areas is an important issue for future urban development. Electrical resistivity tomography is a non-destructive geophysical technique that can detect and characterize such subsurface cavities based on differences in the behaviour of electrical current in the void and in the embedding rock. Here we present a study in which this technique was used to determine the location of old engineered structures around the city of Linares, southern Spain, and to relate these structures to the abandoned deep mines present in the area. Eight electrical resistivity imaging profiles were performed, with a total of 22 808 measurements. Correlations between geoelectrical anomalies allow detection of the depth and the direction of several galleries, as well as the voids that result from mining extraction. Given the depth at which these structures are located (in some cases less than 5 m), they pose an important risk for future construction projects in areas of urban expansion. This technique is shown to be a useful tool for locating areas that pose important urban risks and, by extension, for the decision-making process in territorial planning, especially in areas with a history of deep mining.

Electrical resistivity imaging survey to detect uncharted mine galleries in the mining district of Linares, Jaén, Spain

International Nuclear Information System (INIS)

Martínez-López, J; Rey, J; Hidalgo, C; Dueñas, J; Benavente, J

2012-01-01

The scarcity of information about the existence of old mining shafts and galleries in urban areas is an important issue for future urban development. Electrical resistivity tomography is a non-destructive geophysical technique that can detect and characterize such subsurface cavities based on differences in the behaviour of electrical current in the void and in the embedding rock. Here we present a study in which this technique was used to determine the location of old engineered structures around the city of Linares, southern Spain, and to relate these structures to the abandoned deep mines present in the area. Eight electrical resistivity imaging profiles were performed, with a total of 22 808 measurements. Correlations between geoelectrical anomalies allow detection of the depth and the direction of several galleries, as well as the voids that result from mining extraction. Given the depth at which these structures are located (in some cases less than 5 m), they pose an important risk for future construction projects in areas of urban expansion. This technique is shown to be a useful tool for locating areas that pose important urban risks and, by extension, for the decision-making process in territorial planning, especially in areas with a history of deep mining

The Strossmayer Gallery in Zagreb in the interwar period: from a utopian project to a renowned institution

Directory of Open Access Journals (Sweden)

Ljerka Dulibic

2016-12-01

Full Text Available The basis of today’s Strossmayer Gallery’s collection is the bequest of European Old Masters’ paintings collected by Bishop J. J. Strossmayer (1815-1905, with the fundamental desire to enlarge the scope of the Croatian cultural tradition through the appropriation of European elite culture. The meaning and function of the Gallery changed considerably over time. Before WWI, the Strossmayer Gallery was a utopian project in the sense that its mission was not only to fabricate what was seen to be a missing artistic past, but also to create the foundations for a future, native art. After WWI, with the formation of the Kingdom of Serbs, Croats and Slovenes, the national state was, at least in some form, realized, and the Gallery now turned its attention to concrete matters. In this paper, we follow the paths of intensive professionalization of the wide range of activities in the interwar period, retracing not only the history of museum presentation, or the history of Art History and of Art Conservation in Croatia, but also some traces of the general development of the dynamic, intertwined and significant relationship between Art History, Art Conservation and the museum. Il nucleo dell’odierna collezione della Galleria Strossmayer è costituito dal lascito delle opere dei maestri antichi europei raccolti dal vescovo J.J. Strossmayer (1815-1905, il cui scopo fondamentale fu di allargare la tradizione culturale croata con l’appropriazione della cultura elitaria europea. Con il passare del tempo, il signifi cato e la funzione della Galleria cambiò considerevolmente. Prima della Prima guerra mondiale la Galleria Strossmayer fu un progetto utopistico nel senso che la sua missione non era solo di riempire il vuoto visto come il passato artistico mancante, ma anche di creare le fondamenta per una futura arte locale. Dopo la guerra, con la formazione del Regno dei Serbi, Croati e Sloveni, lo stato nazionale fu, almeno in un certo senso, realizzato, e

The Sulphate Effect on Lijiaxia Concrete Dam (China Gallery

Directory of Open Access Journals (Sweden)

Xufen Zhu

2017-01-01

Full Text Available The concrete degradation is one of the most serious problems for a dam construct during the normal operation, which determines the dam service life. Hence, it is very important to reduce the extent of the dam concrete degradation for the safety of the dam normal operation. Here, Lijiaxia hydroelectric station is taken as an example, and a comprehensive method to assess the sulphate effect on dam gallery is proposed. Eleven samples in total were taken from three difference locations by the drill bore. The microstructural investigations including X-ray fluorescence spectrometry (XRF, X-ray diffraction (XRD, scanning electron microscope (SEM, and energy dispersive spectroscopy (EDS were conducted to assess the sulphate attack and the degradation degree. Meanwhile, the water chemical analysis was applied to reveal the mechanism of concrete degradation. The experimental and analysis results indicate that the concrete degradation degree varies with the location of the samples. The components of the concrete change and the content of SO3 increase dramatically during degradation. Moreover, the mineral facies of the concrete change correspondingly, with the cement paste substituted by the calcite, calcium vitriol, and gypsum. The reinforcement and precaution measures are suggested based on the results of the degradation assessment.

Geotechnical and large numeric studies on direct ultimate disposal of spent fuel elements. Project part 1: Thermal simulation of gallery storage. Final report (8th report)

International Nuclear Information System (INIS)

Heusermann, S.; Liedtke, L.; Soennke, J.; Sprado, K.H.; Gloeggler, W.

1995-01-01

Short-term tension measurements show that a reduced rock tension level exists in the Thermal Storage Simulation field (TSS). This tension level is markedly lower than the lithostatic rock pressure to be expected in the salt rock. The long-term tension measurements show that tension maxima will develop until early in 1993 in the close-in area of the experimental fields, for instance in the pillar between the galleries A and B. Creep tests with salt rock specimens from the TSS field show that the creep performance at room temperature of the Na2β rock salt to be considered in the experimental fields can be sufficiently accurately described by the reference creep law for stationary creep used by the BGR (Bundesanstalt f. Geowissenschaften und Rohstoffe).The experimental in-situ results on the permeability of the salt rock in the experimental fields indicate i.a. very low permeabilities, except for a restricted, local area within the loosening zone below gallery B. This exhibits relatively high permeabilities. The experimental in-situ results on the permeability of the backfilling in the experimental galleries show that during the experimental measuring period, an only small change in permeability due to compaction of the backfilling material was observed. This result agrees with results of compaction tests performed by the GSF. The measured results show a difference in permeabilities between backfilling material subject to heating up, and colder material. (orig.) [de

How to use The National Gallery as a cross curricular approach to weather and climate studies at primary level.

Science.gov (United States)

Hansen, P. J. K.

2009-09-01

How to use The National Gallery as a cross curricular approach to weather and climate studies at primary level. Pål J. Kirkeby Hansen Faculty of Education and International Studies, Oslo University College (PalKirkeby.Hansen@lui.hio.no) Weather and climate are topics in natural science and geography in primary and secondary education in most countries. The pupils are often doing own weather observations and measurements and are presenting the results oral, by posters or with digital aids. They also use the Internet with all its relevant resources in their studies to develop vocabulary, practical and conceptual knowledge. Knowledge about weather and climate is parts of liberal education and could be projected to other topics in science and to topics in other subjects, for instance: history, social geography, literature and arts. This article reports from a case study in grade 3 classes (age 9 year) during their Weather Week. Their science teacher was, quite untypical, also educated in art history. She arranged a visited to The National Gallery with the double agenda: 1. To introduce the pupils to Norwegian canon paintings from the national romantic period, our so-called "golden age”. 2. To look for and discuss weather elements in this paintings. For one hour the museum curator guided the pupils around the water cycle by using the paintings. While the pupils' own observations of weather, clouds and wind and measurements of temperature and precipitation during the Weather Week only are point checks, the guided tour in The National Gallery gave literally "the whole picture” of the Norwegian weather and climate and of the water cycle. During the tour, the curator constantly invited the pupils to tell about and discuss what weather and water elements they were looking at when standing in front of a painting. The pupils were responsive and interested all the time. Back at school, they demonstrated that they had learned much about both weather elements, the water

Voice over: Audio-visual congruency and content recall in the gallery setting.

Science.gov (United States)

Fairhurst, Merle T; Scott, Minnie; Deroy, Ophelia

2017-01-01

Experimental research has shown that pairs of stimuli which are congruent and assumed to 'go together' are recalled more effectively than an item presented in isolation. Will this multisensory memory benefit occur when stimuli are richer and longer, in an ecological setting? In the present study, we focused on an everyday situation of audio-visual learning and manipulated the relationship between audio guide tracks and viewed portraits in the galleries of the Tate Britain. By varying the gender and narrative style of the voice-over, we examined how the perceived congruency and assumed unity of the audio guide track with painted portraits affected subsequent recall. We show that tracks perceived as best matching the viewed portraits led to greater recall of both sensory and linguistic content. We provide the first evidence that manipulating crossmodal congruence and unity assumptions can effectively impact memory in a multisensory ecological setting, even in the absence of precise temporal alignment between sensory cues.

Art on the Moon?

DEFF Research Database (Denmark)

Lee, Rosemary; Minch, Manuel

2018-01-01

Manuel Minch launched Internet Moon Gallery in 2016 with the intention of exploring new modes of creating and engaging with digital art. This article is the result of a collaborative conversation between Manuel Minch and Rosemary Lee, which has evolved from their work together on the exhibition...... “Memory Palace”, launched on Internet Moon Gallery on the full moon, May 2017....

The Novohrad Museum and Gallery in Lučenec past and present (História a súčasnosť Novohradského múzea a galérie v Lučenci

Directory of Open Access Journals (Sweden)

Michaela Škodová

2016-09-01

Full Text Available The Novohrad Museum and Gallery in Lučenec specializes in the regional history of enamel- and glass-making and visual arts. It holds a collection of over 30,000 art, archeo-logical, historical and ethnological objects. Since 1983, the musem and gallery have been a host to the annual Acquarelle Triennale and since 1989, it has hosted the oldest symposium of its kind in Slovakia, the International Ceramic Symposium, which showcases the contemporary ceramic production in Slovakia. This paper outlines the history of the museum and its focus, concentrating on the work done in the last decade.

Multi-mode technique for the determination of the biaxial Y{sub 2}SiO{sub 5} permittivity tensor from 300 to 6 K

Energy Technology Data Exchange (ETDEWEB)

Carvalho, N. C., E-mail: natalia.docarmocarvalho@research.uwa.edu.au; Le Floch, J-M.; Tobar, M. E. [School of Physics, The University of Western Australia, Crawley 6009 (Australia); ARC Centre of Excellence for Engineered Quantum Systems (EQuS), 35 Stirling Hwy, Crawley 6009 (Australia); Krupka, J. [Instytut Mikroelektroniki i Optoelektroniki PW, Koszykowa 75, 00-662 Warsaw (Poland)

2015-05-11

The Y{sub 2}SiO{sub 5} (YSO) crystal is a dielectric material with biaxial anisotropy with known values of refractive index at optical frequencies. It is a well-known rare-earth (RE) host material for optical research and more recently has shown promising performance for quantum-engineered devices. In this paper, we report the first microwave characterization of the real permittivity tensor of a bulk YSO sample, as well as an investigation of the temperature dependence of the tensor components from 296 K down to 6 K. Estimated uncertainties were below 0.26%, limited by the precision of machining the cylindrical dielectric. Also, the electrical Q-factors of a few electromagnetic modes were recorded as a way to provide some information about the crystal losses over the temperature range. To solve the tensor components necessary for a biaxial crystal, we developed the multi-mode technique, which uses simultaneous measurement of low order whispering gallery modes. Knowledge of the permittivity tensor offers important data, essential for the design of technologies involving YSO, such as microwave coupling to electron and hyperfine transitions in RE doped samples at low temperatures.

Anisotropic modelling of Opalinus Clay behaviour: From triaxial tests to gallery excavation application

Directory of Open Access Journals (Sweden)

François Bertrand

2017-06-01

Full Text Available Deep repository in geological formations is the preferential solution considered in many countries to manage high-level nuclear wastes. In Switzerland, the Opalinus Clay is a candidate host rock. In this context, in situ and laboratory tests are conducted on Opalinus Clay to demonstrate the feasibility of deep disposal in this argillaceous formation. This paper presents a constitutive model able to fit the experimental data obtained from some triaxial tests conducted by Jahns (2013 on cores from borehole Schlattingen SLA-1. The elasto-plastic behaviour of Opalinus Clay is reproduced thanks to a Drucker-Prager model, taking into account the anisotropy behaviour of this sedimentary rock. The objective is to employ a single set of parameters representative of the material. In a second version of the model, the stress-dependence of the elastic properties and damage are taken into account. Finally, the parameters calibrated with experimental tests are used to simulate the excavation of a gallery with a second gradient approach.

Investigations for a change of an excavation damaged zone with time at the 250 m gallery in the Horonobe Underground Research Laboratory

International Nuclear Information System (INIS)

Aoyagi, Kazuhei; Tsusaka, Kimikazu; Kondo, Keiji; Inagaki, Daisuke; Kubota, Kenji; Tokiwa, Tetsuya

2014-01-01

The authors have been conducting seismic and resistivity tomography surveys in a gallery of the Horonobe Underground Research Laboratory in order to investigate an extent of an Excavation Damaged Zone (EDZ) along time. The objective of this paper is to discuss an influence of fracture distribution and water saturation of a rock mass on variations in seismic velocity and the value of apparent resistivity in an EDZ. Based on the result of seismic tomography survey, the extent of a layer which has low seismic velocity was about 1.0 m from the gallery wall after excavation of the tomography area. From the results of resistivity tomography survey, the value of apparent resistivity has not changed remarkably along time. To investigate a relationship between variations in seismic velocity and density of fracture in the survey area, the authors built a three dimensional fracture model around the tomography area. From the comparison of seismic velocity with density of fracture, seismic velocity decreased almost linearly as the density of fracture increased. Also, it was found that density of fracture in the layer of low seismic velocity could be estimated using a simple numeric model. >From this result, seismic tomography survey and investigation of density of fracture are suitable method for evaluation of an EDZ. (author)

Advanced Quasioptical Launcher System. Final Report

International Nuclear Information System (INIS)

Neilson, Jeffrey

2010-01-01

This program developed an analytical design tool for designing antenna and mirror systems to convert whispering gallery RF modes to Gaussian or HE11 modes. Whispering gallery modes are generated by gyrotrons used for electron cyclotron heating of fusion plasmas in tokamaks. These modes cannot be easily transmitted and must be converted to free space or waveguide modes compatible with transmission line systems.This program improved the capability of SURF3D/LOT, which was initially developed in a previous SBIR program. This suite of codes revolutionized quasi-optical launcher design, and this code, or equivalent codes, are now used worldwide. This program added functionality to SURF3D/LOT to allow creating of more compact launcher and mirror systems and provide direct coupling to corrugated waveguide within the vacuum envelope of the gyrotron. Analysis was also extended to include full-wave analysis of mirror transmission line systems. The code includes a graphical user interface and is available for advanced design of launcher systems.

An Allergen Portrait Gallery: Representative Structures and an Overview of IgE Binding Surfaces

Directory of Open Access Journals (Sweden)

Ovidiu Ivanciuc

2010-10-01

Full Text Available Recent progress in the biochemical classification and structural determination of allergens and allergen–antibody complexes has enhanced our understanding of the molecular determinants of allergenicity. Databases of allergens and their epitopes have facilitated the clustering of allergens according to their sequences and, more recently, their structures. Groups of similar sequences are identified for allergenic proteins from diverse sources, and all allergens are classified into a limited number of protein structural families. A gallery of experimental structures selected from the protein classes with the largest number of allergens demonstrate the structural diversity of the allergen universe. Further comparison of these structures and identification of areas that are different from innocuous proteins within the same protein family can be used to identify features specific to known allergens. Experimental and computational results related to the determination of IgE binding surfaces and methods to define allergen-specific motifs are highlighted.

Plant food resources and the diet of a parrot community in a gallery forest of the southern Pantanal (Brazil

Directory of Open Access Journals (Sweden)

J. Ragusa-Netto

Full Text Available Neotropical parrots usually forage in forest canopies for nectar, flowers, leaves, fruit pulp, and seeds. As they have no all-purpose territories, these birds usually exploit vegetation mosaics in order to use plentiful resources as they become available. In this study we examine the use of a gallery forest in the southern Pantanal (Brazil by a diverse parrot community that ranged from Brotogeris chiriri (a small species to Ara chloroptera (a large one. Plant food resources principally used by parrots were abundantly available during the rainy season (fleshy fruits, the annual floods (fleshy fruits, and the dry season (flowers. While both smaller and larger species foraged on fruits, parakeets largely consumed the pulp, while larger parrot species used pulp and seeds. In the dry season parakeets foraged extensively on nectar, especially Inga vera nectar that was abundantly available during the last two months of the dry season, the harshest period of the year. Among larger parrots, only Propyrrhura auricollis frequently harvested nectar. Fruits maturing during floods, despite being fish- or water- dispersed were extensively used by the parrots. Hence, unlike what happens in most other Neotropical dry forests, occurrence of a fruiting peak during the annual flooding, which occurs in the transition from the wet to the dry season, constitutes an extra and significant episode of food availability, since in this period, fruit production normally declines. Therefore, the unique and abundant availability of flowers and fruits in this gallery forest may account for the presence of large parrot populations in the southern Pantanal.

PENINGKATAN AKTIVITAS DAN HASIL BELAJAR AKUNTANSI MATERI LAPORAN KEUANGAN MELALUI METODE GALLERY WALK DUATI-DUATA

Directory of Open Access Journals (Sweden)

Nining Mariyaningsih

2014-06-01

Full Text Available In learning accounting, conventional learning models are still frequently used by the teacher. As a result, the learning become monotonous and it’s not maximum. The problem of this study is wheather through Gallery Walk Duati-Duata can improve the activity and learning outcomes of accounting students.This study was class action research which was designed into two main cycles. Each cycle consisted of four stages started from planning, acting, observing and reflecting. The result showed that : (1 Learning activities increase from 27,78% before cycle, 69,45% in first cycle and 93,88% in second cycle, (2 The learning outcomes increase, from 22,22% before siklus, 75% in first cycle and 94,44% in second cycle. Therefore the use of this methods could be one of the reference of teachers in implementing the learning process.

Geophysical monitoring of the EDZ during a gallery excavation in the Opalinus clay of the Mont Terri URL: anomalies of noble gases and self-potential associated with fractures and fluid dynamics in a horizontal borehole

International Nuclear Information System (INIS)

Maineult, A.; Mahiouz, K.; Lesparre, N.; Thomas, B.; Lavielle, B.; Nussbaum, C.; Wieczorek, K.; Gibert, D.; Kergosien, B.; Nicollin, F.

2012-01-01

Document available in extended abstract form only. The research underground rock laboratory (URL) of Mont Terri (Switzerland) was established in 1996 in a Mesozoic clay-stone formation (Opalinus Clay). It is aimed at studying the hydro-mechanical, thermal, geochemical and geophysical behaviour of argillaceous formations in the context of radioactive waste disposal. The EZ-G experiments were designed to monitor the EDZ evolution. The EZ-G08 experiment started in September 2007 to study the EDZ changes at different time scales during the tunnelling of gallery Ga08 starting from the northern part of the URL toward the end-face of the gallery Ga04. Before the excavation process started, we characterized the petrology and the structural properties of the core of the horizontal, 12-m long borehole BEZ-G5 drilled in the end-face of gallery Ga04 (first 2 meters in the shaly facies, the rest in the sandy facies). We quantified its noble gas content for studying gas transport processes in rocks and connected fracture networks. Depletion in He can be observed in the EDZ and other noble gases can also increase as desaturation processes occur. Inflows of water occurred in the borehole few weeks after its drilling until the junction of galleries Ga08 and Ga04. Water amounts of few litres were commonly released in other boreholes in the URL. We recorded the natural electrical potentials (self-potentials - SP), in BEZ-G5. SP originate from the movement of fluid, the diffusion of concentration or temperature gradients, and are sensitive to any change occurring in them. Borehole BEZ-G5 was equipped with a specific device, on which custom-made electrodes were fixed every 15 cm. The signals showed coherent perturbations during the drilling operations in the boreholes BEZ-G12 and in the end-face of the gallery Ga04. Afterwards, an early, strong but rather smooth increase of a few tens of mV, followed by a very slow decrease of much smallest amplitude, can be observed in some signals

Multimode laser emission from dye-doped hollow polymer optical fibre

Indian Academy of Sciences (India)

2014-02-09

Feb 9, 2014 ... Fibre lasers; optical microcavities; whispering gallery modes. ... A blueshift in the mode structure was observed with decrease in fibre diameter leading to wide range tunability of the laser emission. ... International School of Photonics, Cochin University of Science & Technology, Cochin 682 022, India ...

Chaos-assisted broadband momentum transformation in optical microresonators

Science.gov (United States)

Jiang, Xuefeng; Shao, Linbo; Zhang, Shu-Xin; Yi, Xu; Wiersig, Jan; Wang, Li; Gong, Qihuang; Lončar, Marko; Yang, Lan; Xiao, Yun-Feng

2017-10-01

The law of momentum conservation rules out many desired processes in optical microresonators. We report broadband momentum transformations of light in asymmetric whispering gallery microresonators. Assisted by chaotic motions, broadband light can travel between optical modes with different angular momenta within a few picoseconds. Efficient coupling from visible to near-infrared bands is demonstrated between a nanowaveguide and whispering gallery modes with quality factors exceeding 10 million. The broadband momentum transformation enhances the device conversion efficiency of the third-harmonic generation by greater than three orders of magnitude over the conventional evanescent-wave coupling. The observed broadband and fast momentum transformation could promote applications such as multicolor lasers, broadband memories, and multiwavelength optical networks.

Orchid bee (Hymenoptera: Apidae community from a gallery forest in the Brazilian Cerrado

Directory of Open Access Journals (Sweden)

Francinaldo S Silva

2012-06-01

Full Text Available The orchid bees are a very important group of pollinators distributed in the Neotropics. Although a lot of studies concerning male euglossine bees have been done in this region, few works have so far been carried out in the Cerrado biome. This manuscript has the main objective to present the orchid bee community from a Gallery Forest in the Northeastern Brazilian Cerrado landscape, taking account the species composition, abundance, seasonality and hourly distribution. Male euglossine bees were collected monthly from October 2007 to May 2009, in the Reserva Florestal da Itamacaoca belonging to the Companhia de Água e Esgoto do Maranhão, in Chapadinha municipality, Maranhão State. The scents eucalyptol, eugenol and vanillin were utilized, between 07:00 and 17:00hr, to attract the euglossine males. Cotton balls were dampened with the scents and suspended by a string on tree branches 1.5m above soil level, set 8m from one another. The specimens were captured with entomological nets, killed with ethyl acetate and transported to the laboratory to be identified. A total of 158 individuals and 14 species of bees were recorded. The genus Eulaema was the most representative group of euglossine bees in relation to the total number of the sampled individuals, accounting for 50.6% of bees followed by Euglossa (26.6%, Eufriesea (15.2% and Exaerete (7.6%. The most frequent species were Eulaema nigrita (27.8%, Eulaema cingulata (19% and Euglossa cordata (18.3%. Many species typical of forested environments were found in samples, like Euglossa avicula, Euglossa violaceifrons and Eulaema meriana, emphasizing the role played by the Gallery Forests as bridge sites to connect the two great biomes of Amazonia and Atlantic Forest. The occurrence of Exaerete guaykuru represents the second record of this species for the Neotropical region, and both records coming from the Gallery Forest zones. The male euglossine bees were sampled mainly in the dry season, where 62

Walk, Look, Remember: The Influence of the Gallery's Spatial Layout on Human Memory for an Art Exhibition.

Science.gov (United States)

Krukar, Jakub

2014-09-01

The spatial organisation of museums and its influence on the visitor experience has been the subject of numerous studies. Previous research, despite reporting some actual behavioural correlates, rarely had the possibility to investigate the cognitive processes of the art viewers. In the museum context, where spatial layout is one of the most powerful curatorial tools available, attention and memory can be measured as a means of establishing whether or not the gallery fulfils its function as a space for contemplating art. In this exploratory experiment, 32 participants split into two groups explored an experimental, non-public exhibition and completed two unanticipated memory tests afterwards. The results show that some spatial characteristics of an exhibition can inhibit the recall of pictures and shift the focus to perceptual salience of the artworks.

Development and validation of a CFD model predicting the backfill process of a nuclear waste gallery

International Nuclear Information System (INIS)

Gopala, Vinay Ramohalli; Lycklama a Nijeholt, Jan-Aiso; Bakker, Paul; Haverkate, Benno

2011-01-01

Research highlights: → This work presents the CFD simulation of the backfill process of Supercontainers with nuclear waste emplaced in a disposal gallery. → The cement-based material used for backfill is grout and the flow of grout is modelled as a Bingham fluid. → The model is verified against an analytical solution and validated against the flowability tests for concrete. → Comparison between backfill plexiglas experiment and simulation shows a distinct difference in the filling pattern. → The numerical model needs to be further developed to include segregation effects and thixotropic behavior of grout. - Abstract: Nuclear waste material may be stored in underground tunnels for long term storage. The example treated in this article is based on the current Belgian disposal concept for High-Level Waste (HLW), in which the nuclear waste material is packed in concrete shielded packages, called Supercontainers, which are inserted into these tunnels. After placement of the packages in the underground tunnels, the remaining voids between the packages and the tunnel lining is filled-up with a cement-based material called grout in order to encase the stored containers into the underground spacing. This encasement of the stored containers inside the tunnels is known as the backfill process. A good backfill process is necessary to stabilize the waste gallery against ground settlements. A numerical model to simulate the backfill process can help to improve and optimize the process by ensuring a homogeneous filling with no air voids and also optimization of the injection positions to achieve a homogeneous filling. The objective of the present work is to develop such a numerical code that can predict the backfill process well and validate the model against the available experiments and analytical solutions. In the present work the rheology of Grout is modelled as a Bingham fluid which is implemented in OpenFOAM - a finite volume-based open source computational fluid

Development of and horizontal seams wining system by means of galleries and chambers; Demostracion de un Sistema de Explotacion de Capas Horizontales por el Metodo de Pilares y Galerias Trazadas Integramente con Maquinas de Ataque Puntual

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The project Development of an horizontal seams wining system by means of galleries and chambers aimed on the solution of a mining problem kept unresolved during the last 35 years in Carrasconte mine, owned by the society Minero Siderurgica de Ponferrada, in the coal yield of Villablino, Leon, Spain. The problem was a horizontal seam, with a width from 2,5 to 3,5 m, with two specific characteristics; one, roof and floor extremely rigid, with a 30 m sandstone stratum by roof that practically could highly restrict the long wall face conventional system, and the other, an intercalation of shale with a width of 1,2 m and a hardness of near 400 kg/cm2 that required a suitable winning system. By means of investigation with galleries carried out by continuous miners the real width of shale intercalation was stated, an then suitable systems adopted as this width varied. So, short wall faces in areas with minimum shale were disposed, and in t areas with maximum shale width, two long wall faces each one in each different vein were designed. At the end, the borders of reserves were recovered by the conventional system of galleries and chambers. This development project has allowed to recover more than a million tons in three years by systems suitable to the different conditions of the seam. (Author)

Feasibility for Use of a Seabed Gallery Intake for the Shuqaiq-II SWRO Facility, Saudi Arabia

KAUST Repository

Mantilla, David

2013-04-01

Shuqaiq-II IWP is a combined RO water desalination and power plant facility. It operates with an open intake that feeds the plant with 100,000 m3/h of raw water. The facility is located 140 km north of Jizan, in a small bay where the run-off discharges of two wadis converge. The run-off coming from the wadis are rich in alluvial sediments that dramatically decrease the raw water quality at the intake point, causing periodic shutdowns of the plant and increasing the operational cost due to membrane replacement. Subsurface water intakes are an alternative for improving raw water quality, as they provide natural filtering of the feed water as it flows through the systems. In this type of system water flow through the sediment matrix is induced and during the percolation, several physical, chemical and biological processes take place, cleaning the water from particulate matter, resulting in high quality feed water that can be directly sent to the RO process without any additional pretreatment. A full hydrogeological profile of the seabed needs to be performed in order to determine the applicability of one of these systems in each particular location. In this study, 1 km of beach area at Shuqaiq-II IWP was surveyed. Ninety-one (91) samples from the shore and offshore sediments were collected and analyzed for hydraulic conductivity, porosity and grain size distribution. The laboratory analysis showed that the construction of the seabed galleries was technically feasible, and the proposed intake system was design to meet the feed water requirements for the RO facility (530.000 m3/d). The preliminary design consists of 17 cells in total, 16 of which will be in constant operation, and 1 alternate for whenever maintenance is needed in one of the other cells. The seabed gallery design includes 5 layers of sands with a total depth of 5 m. A detailed underdrain design methodology is presented. The system would be operated at an infiltration rate of 10 m/d and an average

Nonlinear Optical Terahertz Technology

Data.gov (United States)

National Aeronautics and Space Administration — We develop a new approach to generation of THz radiation. Our method relies on mixing two optical frequency beams in a nonlinear crystalline Whispering Gallery Mode...

Sulla digitalizzazione della street art. Linee guida per un'analisi del museo virtuale Reggiane Urban Gallery

Directory of Open Access Journals (Sweden)

Damiano Razzoli

2017-09-01

Full Text Available Reggiane Urban Gallery is a virtual museum based on the abandoned industrial plant of ex-Officine Reggiane in Reggio Emilia, now in restoration. Along the years the place has become an open space for local and national street-artists. The aim of this paper is to analyze the use of virtual reality and navigable interface as a solution for the conservation of the Street Art, in relation to the fact that many pieces would have been lost due to the demolition of several walls. Also, the analysis proposes guidelines for a digitalization of Street Art that could prevent the displacement of situated Street Art pieces in museums and encourage the creation of street art locative media museum, supported on four concepts - dispositive/device, locativity, topographic database, interface - and one discoursive feature designing the mediated experience of urban crossing practices: the mimetical relation between the software cultural components and Street Art.

Desaturation of a clay-stone around a ventilated gallery: numerical modelling of pressures and water contents under various conditions

International Nuclear Information System (INIS)

Ababou, Rachid; Mansouri, Nahla; Bailly, David; Poutrel, Adrien

2012-01-01

Document available in extended abstract form only. We present simulation tests focusing on the drying process around a gallery in an initially saturated (water-filled) porous clay rock, in the framework of a research on the isolation properties and hydro-mechanical behaviour of a clayey geologic repository for radioactive waste. The saturated/unsaturated hydrodynamic parameters used in these tests correspond to a hypothetical clay-stone, similar to the 130 m thick Callovo-Oxfordian formation located between depths 400 m and 600 m at the Meuse / Haute-Marne (MHM) Underground Research Laboratory (URL), operated by ANDRA (Bure, France). The simulations tests were designed according to 3 'types' of computational geometries. The drying period was extended to very long time scales in some cases. The clay rock was taken homogeneous in many tests, but the damaged zone was represented in some (Type III) tests. Type (I) tests are conducted in a simplified non circular geometry. Assuming a square cross-section for the drift, the drying process is obtained by imposing a fixed suction on a flat piece of wall at the roof. The bottom of the porous domain coincides with the roof of the drift. The imposed suction at the roof affects the near field pressure both horizontally and vertically. Type (II) tests reproduce the circular cylindrical geometry of a partially or perfectly filled gallery, with drying conditions imposed at both ends of the drift. Finally, Type (III) tests consider the case of an empty ventilated cylindrical drift with circular cross-section. In this case the drying is imposed on the curved walls of the drift via a transmission mechanism thanks the 'macro-porous immersion' method. In all cases, the drying of the porous clay rock is modeled by imposing a suction condition (ψ), obtained from relative air humidity (HR) via Kelvin's law (ψ). Briefly, the macro-porous immersion method consists in the following interrelated procedures. First, the volumetric excavation

Seabed gallery intakes: Investigation of the water pretreatment effectiveness of the active layer using a long-term column experiment

KAUST Repository

Dehwah, Abdullah

2017-05-11

Seabed gallery intake systems used for seawater reverse osmosis facilities employ the same principle of water treatment as slow sand filtration in freshwater systems. An investigation concerning the effectiveness of the active layer (top layer) in improving raw water quality was conducted by using a long-term bench-scale columns experiment. Two different media types, silica and carbonate sand, were tested in 1 m columns to evaluate the effectiveness of media type in terms of algae, bacteria, Natural Organic Matter (NOM) and Transparent Exopolymer Particles (TEP) removal over a period of 620 days. Nearly all algae in the silica sand column, 87% (σ = 0.04) of the bacteria, 59% (σ = 0.11) of the biopolymer fraction of NOM, 59% (σ = 0.16) of particulate and 32% (σ = 0.25) of colloidal TEP were removed during the last 330 days of the experiment. Total removal was observed in the carbonate sand column for algal concentration, while the bacterial removal was lower at 74% (σ = 0.08). Removal of biopolymers, particulate and colloidal TEP were higher in the carbonate column during the last 330 days with 72% (σ = 0.15), 66% (σ = 0.08) and 36% (σ = 0.12) removed for these organics respectively. Removal of these key organics through the 1 m thick column, representing the active layer, will likely reduce the rate of biofouling, reduce chemical usage and minimize operating cost in SWRO systems. The data show that the media will require several months at the beginning of operation to reach equilibrium so that high organic removal rates can be achieved. No development of a “schmutzdecke” layer occurred. The experimental results suggest that unlike freshwater slow sand filtration wherein most water treatment occurs in the upper 10 cm, in seawater systems treatment occurs throughout the full active layer depth of 1 m. The results of this study will help in designing and operating seabed gallery intake systems in varied geological conditions.

Parallel inversion of a massive ERT data set to characterize deep vadose zone contamination beneath former nuclear waste infiltration galleries at the Hanford Site B-Complex (Invited)

Science.gov (United States)

Johnson, T.; Rucker, D. F.; Wellman, D.

2013-12-01

The Hanford Site, located in south-central Washington, USA, originated in the early 1940's as part of the Manhattan Project and produced plutonium used to build the United States nuclear weapons stockpile. In accordance with accepted industrial practice of that time, a substantial portion of relatively low-activity liquid radioactive waste was disposed of by direct discharge to either surface soil or into near-surface infiltration galleries such as cribs and trenches. This practice was supported by early investigations beginning in the 1940s, including studies by Geological Survey (USGS) experts, whose investigations found vadose zone soils at the site suitable for retaining radionuclides to the extent necessary to protect workers and members of the general public based on the standards of that time. That general disposal practice has long since been discontinued, and the US Department of Energy (USDOE) is now investigating residual contamination at former infiltration galleries as part of its overall environmental management and remediation program. Most of the liquid wastes released into the subsurface were highly ionic and electrically conductive, and therefore present an excellent target for imaging by Electrical Resistivity Tomography (ERT) within the low-conductivity sands and gravels comprising Hanford's vadose zone. In 2006, USDOE commissioned a large scale surface ERT survey to characterize vadose zone contamination beneath the Hanford Site B-Complex, which contained 8 infiltration trenches, 12 cribs, and one tile field. The ERT data were collected in a pole-pole configuration with 18 north-south trending lines, and 18 east-west trending lines ranging from 417m to 816m in length. The final data set consisted of 208,411 measurements collected on 4859 electrodes, covering an area of 600m x 600m. Given the computational demands of inverting this massive data set as a whole, the data were initially inverted in parts with a shared memory inversion code, which

Effects of nearshore evaporation rates on the design of seabed gallery intake systems for SWRO facilities located along the Red Sea shoreline of Saudi Arabia

KAUST Repository

Dehwah, Abdullah

2015-10-12

Feed water to seawater reverse osmosis desalination systems should have a constant salinity with minimal variation. Intake systems that extract water from shallow nearshore areas in arid regions can exhibit significant fluctuations in salinity caused by high rates of evaporation and lack of circulation. Such fluctuations in salinity could inhibit the design, construction, and operation of seabed gallery intake systems located in shallow nearshore areas, such as the Red Sea inner shelf. Water depths range from 0 to 2 m between the beach and the edge of the fringing reef in the optimal locations for the development of seabed gallery intakes along the coast of the Red Sea of Saudi Arabia. The evaporation rate in this area is between 2 and 3 m per year. The bottom consists of mostly a marine hardground containing a thin veneer of unlithified sediment and no significant cover of corals or seagrass. The rather barren nature of the bottom suggests that periodic hypersalinity may contribute to the formation of hardgrounds on the bottom by causing supersaturation of the seawater with calcium carbonate and may limit the growth of corals and grasses. To assess the changes in salinity, a conceptual model was developed which assumes that a shallow circulation cell develops between the shoreline and deeper water offshore. Lower salinity seawater should migrate landward to replace water loss caused by evaporation with seaward moving of high-salinity water occurring along the bottom to balance the flow with ultimate mixing before the reef tract. To test this circulation pattern, a series of sensors were deployed to continuously monitor the water temperature, conductivity, and salinity at the surface and at the bottom during several periods of high air temperature. Surprisingly, the results show very little variation in salinity, despite the very high evaporation loss. The water salinity ranged between 39,000 and 40,000 mg/L with no diurnal variations of significance. Based on the

Thermal Stability of Clay's Galleries in Polypropylene - Clay (montmorillonite Nanocomposites using Polypropylene-gMaleic Anhydride as Compatibilizer

Directory of Open Access Journals (Sweden)

Sotya Astutiningsih

2010-10-01

Full Text Available Superior properties of food packaging can be achieved using nanocomposite technology. However, fabrication of this materials are complex and expensive. Long term objectives of this research is the synthesis of low cost polypropylene clay nanocomposites (PPCN via a short-cut method known as ‘cascade engineering’. Cascade engineering principle in PPCN fabrication is performed by using compatibilizer (to enable the mixing of PP and clay masterbatch, and PPCN in one pot process using melt mixer. This paper present the experimental results using small-angle x-ray diffraction (XRD on the thermal stability of the PPCN. Results from the XRD analysis showed that the clay was intercalated, however no significant changes were observed as a result of variation in mixing time. XRD patterns of the annealed PPCN showed reduction of MMT’s gallery (deintercalation These phenomenon was probably caused by insufficient bonding and lack of compatibility between PP-g-MA and MMT.

Chaos-assisted broadband momentum transformation in optical microresonators.

Science.gov (United States)

Jiang, Xuefeng; Shao, Linbo; Zhang, Shu-Xin; Yi, Xu; Wiersig, Jan; Wang, Li; Gong, Qihuang; Lončar, Marko; Yang, Lan; Xiao, Yun-Feng

2017-10-20

The law of momentum conservation rules out many desired processes in optical microresonators. We report broadband momentum transformations of light in asymmetric whispering gallery microresonators. Assisted by chaotic motions, broadband light can travel between optical modes with different angular momenta within a few picoseconds. Efficient coupling from visible to near-infrared bands is demonstrated between a nanowaveguide and whispering gallery modes with quality factors exceeding 10 million. The broadband momentum transformation enhances the device conversion efficiency of the third-harmonic generation by greater than three orders of magnitude over the conventional evanescent-wave coupling. The observed broadband and fast momentum transformation could promote applications such as multicolor lasers, broadband memories, and multiwavelength optical networks. Copyright © 2017 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

Two-mode PLC-based mode multi/demultiplexer for mode and wavelength division multiplexed transmission.

Science.gov (United States)

Hanzawa, Nobutomo; Saitoh, Kuimasa; Sakamoto, Taiji; Matsui, Takashi; Tsujikawa, Kyozo; Koshiba, Masanori; Yamamoto, Fumihiko

2013-11-04

We proposed a PLC-based mode multi/demultiplexer (MUX/DEMUX) with an asymmetric parallel waveguide for mode division multiplexed (MDM) transmission. The mode MUX/DEMUX including a mode conversion function with an asymmetric parallel waveguide can be realized by matching the effective indices of the LP(01) and LP(11) modes of two waveguides. We report the design of a mode MUX/DEMUX that can support C-band WDM-MDM transmission. The fabricated mode MUX/DEMUX realized a low insertion loss of less than 1.3 dB and high a mode extinction ratio that exceeded 15 dB. We used the fabricated mode MUX/DEMUX to achieve a successful 2 mode x 4 wavelength x 10 Gbps transmission over a 9 km two-mode fiber with a penalty of less than 1 dB.

Berenty Reserve—A Gallery Forest in Decline in Dry Southern Madagascar—Towards Forest Restoration

Directory of Open Access Journals (Sweden)

Vanessa Winchester

2018-01-01

Full Text Available Berenty Reserve, a fully protected gallery forest beside the Mandrare River is renowned for its lemurs, but the continuous canopy of the main forest is shrinking, fragmenting and degrading. The aim of this study, before any restoration can be considered, is to investigate why canopy-cover is declining and define the forest’s vegetation status and composition. Our study includes analysis of tamarind age (the dominant species and regeneration, forest extent, climate and soil. Measurement of trunk circumference and annual rings indicated a median age of 190 years, near the accepted maximum for tamarinds. There is no regeneration of tamarind seedlings under the canopy and an invasive vine, Cissus quadrangularis suffocates any regeneration on the forest margins. A vegetation survey, based on fifteen transects, broadly characterized three forest areas: continuous canopy near the river, transitional canopy with fewer tall trees, and degraded dryland; the survey also provided a list of the 18 most common tree species. Ring counts of flood-damaged roots combined with measurement to the riverbank show that erosion rates, up to 19.5 cm/year, are not an immediate threat to forest extent. The highly variable climate shows no trend and analysis of forest soil indicates compatibility with plant growth.

Towards a fully integrated optical gyroscope using whispering gallery modes resonators

Science.gov (United States)

Amrane, T.; Jager, J.-B.; Jager, T.; Calvo, V.; Léger, J.-M.

2017-11-01

Since the developments of lasers and the optical fibers in the 70s, the optical gyroscopes have been subject to an intensive research to improve both their resolution and stability performances. However the best optical gyroscopes currently on the market, the ring laser gyroscope and the interferometer fiber optic gyroscope are still macroscopic devices and cannot address specific applications where size and weight constraints are critical. One solution to overcome these limitations could be to use an integrated resonator as a sensitive part to build a fully Integrated Optical Resonant Gyroscope (IORG). To keep a high rotation sensitivity, which is usually degraded when downsizing this kind of optical sensors based on the Sagnac effect, the resonator has to exhibit a very high quality factor (Q): as detailed in equation (1) where the minimum rotation rate resolution for an IORG is given as a function of the resonator characteristics (Q and diameter D) and of the global system optical system characteristics (i.e. SNR and bandwidth B), the higher the Q×D product, the lower the resolution.

Fourier Transform Surface Plasmon Resonance of Nanodisks Embedded in Magnetic Nanorods.

Science.gov (United States)

Jung, Insub; Ih, Seongkeun; Yoo, Haneul; Hong, Seunghun; Park, Sungho

2018-03-14

In this study, we demonstrate the synthesis and application of magnetic plasmonic gyro-nanodisks (GNDs) for Fourier transform surface plasmon resonance based biodetection. Plasmonically active and magnetically responsive gyro-nanodisks were synthesized using electrochemical methods with anodized aluminum templates. Due to the unique properties of GNDs (magnetic responsiveness and surface plasmon bands), periodic extinction signals were generated under an external rotating magnetic field, which is, in turn, converted into frequency domains using Fourier transformation. After the binding of a target on GNDs, an increase in the shear force causes a shift in the frequency domain, which allows us to investigate biodetection for HA1 (the influenza virus). Most importantly, by modulating the number and the location of plasmonic nanodisks (a method for controlling the hydrodynamic forces by rationally designing the nanomaterial architecture), we achieved enhanced biodetection sensitivity. We expect that our results will contribute to improved sensing module performance, as well as a better understanding of dynamic nanoparticle systems, by harnessing the perturbed periodic fluctuation of surface plasmon bands under the modulated magnetic field.

Multimode laser emission from free-standing cylindrical microcavities

Energy Technology Data Exchange (ETDEWEB)

Peter, Jaison, E-mail: jaisonpeter@cusat.ac.in; Radhakrishnan, P.; Nampoori, V.P.N.; Kailasnath, M.

2014-05-01

We report a well resolved whispering gallery mode (WGM) laser emission from a free-standing microring cavity based on a dye doped hollow polymer optical fiber (DDHPOF), which is transversely pumped by a pulsed Nd:YAG laser. The microring laser is characterized by a well-defined, low threshold pump power at which the emission spectral intensity dramatically increases and collapses into several dominant microcavity laser modes with reduced mode spacing and high Q-value. Resonant modes are excited inside the gain medium which is strongly confined along the radial direction so that the spacing of lasing modes is controlled by the diameter of the cylindrical microcavity. A variation in the free spectral range of WGM spectra from 0.23 to 0.09 nm coupled with a red-shift is observed with an increase in the diameter of DDHPOFs. - Highlights: • Different diameter free-standing cylindrical microcavity lasers have been fabricated and their performances have been evaluated. • The microring laser is characterized by a well-defined, low threshold pump power, with reduced mode spacing and high Q-value. • When the diameter of DDHPOF increases, the number of lasing peaks increases along with the decrease of the FSR as observed from our studies. • It is also found that whispering gallery lasing envelope is shifted from 559 to 571 nm (Stokes shift) with the diameter.

PLC-based mode multi/demultiplexers for mode division multiplexing

Science.gov (United States)

Saitoh, Kunimasa; Hanzawa, Nobutomo; Sakamoto, Taiji; Fujisawa, Takeshi; Yamashita, Yoko; Matsui, Takashi; Tsujikawa, Kyozo; Nakajima, Kazuhide

2017-02-01

Recently developed PLC-based mode multi/demultiplexers (MUX/DEMUXs) for mode division multiplexing (MDM) transmission are reviewed. We firstly show the operation principle and basic characteristics of PLC-based MUX/DEMUXs with an asymmetric directional coupler (ADC). We then demonstrate the 3-mode (2LP-mode) multiplexing of the LP01, LP11a, and LP11b modes by using fabricated PLC-based mode MUX/DEMUX on one chip. In order to excite LP11b mode in the same plane, a PLC-based LP11 mode rotator is introduced. Finally, we show the PLC-based 6-mode (4LP-mode) MUX/DEMUX with a uniform height by using ADCs, LP11 mode rotators, and tapered waveguides. It is shown that the LP21a mode can be excited from the LP11b mode by using ADC, and the two nearly degenerated LP21b and LP02 modes can be (de)multiplexed separately by using tapered mode converter from E13 (E31) mode to LP21b (LP02) mode.

Low-threshold conical microcavity dye lasers

DEFF Research Database (Denmark)

Grossmann, Tobias; Schleede, Simone; Hauser, Mario

2010-01-01

element simulations confirm that lasing occurs in whispering gallery modes which corresponds well to the measured multimode laser-emission. The effect of dye concentration on lasing threshold and lasing wavelength is investigated and can be explained using a standard dye laser model....

Students, teachers and technicians are installing a cosmic ray detector in the CMS visitor gallery. The detector was designed and built in the framework of the US Quarknet project under the supervision of physicists from the Notre Dame University (USA)

CERN Document Server

Claudia Marcelloni

2007-01-01

Students, teachers and technicians are installing a cosmic ray detector in the CMS visitor gallery. The detector was designed and built in the framework of the US Quarknet project under the supervision of physicists from the Notre Dame University (USA)

Fitossociologia de dois trechos inundáveis de Matas de Galeria no Distrito Federal, Brasil Phytosociology of two swamped portions of gallery forests in Distrito Federal, Brazil

Directory of Open Access Journals (Sweden)

Ernestino de Souza Gomes Guarino

2005-09-01

Full Text Available As Matas de Galeria do bioma Cerrado possuem peculiaridades fisionômicas e florísticas que permitem separá-las em dois subtipos: "não-inundável", quando em solos bem drenados; e "inundável", o subtipo menos estudado, em solos mal drenados. O presente trabalho objetivou caracterizar estrutural e floristicamente dois trechos inundáveis das matas dos córregos Acampamento (15°35'S; 48°10'W e Riacho Fundo (15°55'S; 48°02'W no Distrito Federal (DF. Para isso foi alocada em cada Mata uma grade de 160×50 m (0,8 ha, composta por 40 parcelas de 10×20 m (200 m². Todos os indivíduos com diâmetro a 1,30 m da altura do solo (DAP > 3,0 cm foram amostrados, incluindo aqueles mortos ainda em pé. Foram amostrados 6.078 indivíduos, sendo 3.030 no trecho do Acampamento (33 famílias, 49 gêneros e 60 espécies e 3.048 no Riacho Fundo (30 famílias, 41 gêneros, 53 espécies. A área basal e a diversidade (H' calculada para os trechos foram de 47,96 m²/ha e 2,99 nats/ind. (Acampamento, e 41,28 m²/ha e 2,84 nats/ind. (Riacho Fundo, respectivamente. Se comparados com matas anteriormente estudadas no DF os valores de diversidade são baixos, estando na mesma magnitude indicada para as Matas de Brejo (Higrófilas do sudeste brasileiro. Os índices de similaridade indicaram alta semelhança qualitativa (Sørensen 58,0% e quantitativa (Morisita 70,6% entre os trechos estudados, embora uma classificação por TWINSPAN tenha gerado dois grupos distintos, cada qual vinculado a um dos trechos. Os resultados reforçam indicações anteriores de que as Matas de Galeria do DF, ou trechos similares destas, inundáveis ou não, possuem comunidades arbóreas particulares, as quais estão relacionadas à bacia hidrográfica na qual a Mata esta inserida e ao padrão determinante da drenagem do solo.Gallery forests in the Cerrado biome possess physiognomic and floristic peculiarities that allow its division in two subtypes: "non-swamp" located in well drained

Spatial-mode switchable ring fiber laser based on low mode-crosstalk all-fiber mode MUX/DEMUX

Science.gov (United States)

Ren, Fang; Yu, Jinyi; Wang, Jianping

2018-05-01

We report an all-fiber ring laser that emits linearly polarized (LP) modes based on the intracavity all-fiber mode multiplexer/demultiplexer (MUX/DEMUX). Multiple LP modes in ring fiber laser are generated by taking advantage of mode MUX/DEMUX. The all-fiber mode MUX/DEMUX are composed of cascaded mode-selective couplers (MSCs). The output lasing mode of the ring fiber laser can be switched among the three lowest-order LP modes by employing combination of a mode MUX and a simple N × 1 optical switch. The slope efficiencies, optical spectra and mode profiles are measured.

Temporal Dynamics and Resource Availability for Drosophilid Fruit Flies (Insecta, Diptera in a Gallery Forest in the Brazilian Savanna

Directory of Open Access Journals (Sweden)

Henrique Valadão

2010-01-01

Full Text Available Seasonality can cause severe bottlenecks in natural populations, even leading to local extinction. Large variation in resource availability may explain the bottlenecks, but the role of these variations is still poorly understood. The goal of this study was to analyze if temporal variations in the guild of drosophilids breeding in fruits of Mauritia flexuosa (Arecaceae can be explained by the shortage of this resource during the dry season. Fruits of M. flexuosa were collected over one year in a gallery forest located in the Central Brazilian Savanna. The drosophilid assemblage varied over time, with a lower density of species and of individuals in the dry season, when the percentage of colonized fruits was also smaller. These findings suggest that although the fruits were available during the dry season, they were underused. This way, the resource availability does not seem to regulate the community in the dry season.

Temporal Dynamics and Resource Availability for Drosophilid Fruit Flies (Insect, Diptera) in a Gallery Forest in the Brazilian Savanna

International Nuclear Information System (INIS)

Valadao, H.; Du Vall Hay, J.; Tidon, R.

2010-01-01

Seasonality can cause severe bottlenecks in natural populations, even leading to local extinction. Large variation in resource availability may explain the bottlenecks, but the role of these variations is still poorly understood. The goal of this study was to analyze if temporal variations in the guild of drosophilids breeding in fruits of Mauritia flexuosa (Arecaceae) can be explained by the shortage of this resource during the dry season. Fruits of M. flexuosa were collected over one year in a gallery forest located in the Central Brazilian Savanna. The drosophilid assemblage varied over time, with a lower density of species and of individuals in the dry season, when the percentage of colonized fruits was also smaller. These findings suggest that although the fruits were available during the dry season, they were under used. This way, the resource availability does not seem to regulate the community in the dry season.

Uso e Conservação de florestas de galeria do bioma Pampa Brasileiro Anthropogenic use of gallery forests in the Brazilian Pampa - doi: 10.4025/actascibiolsci.v35i2.13458

Directory of Open Access Journals (Sweden)

Valdir Marcos Stefenon

2013-05-01

Full Text Available Como efeito do crescimentop demográfico, muitas cidades no Sul do Brasil experimentaram, na última década, um processo de degradação de áreas de preservação ambiental. O planejamento de programas de recuperação de florestas depende de conhecimento estruturado sobre a utilização de espécies vegetais pelas comunidades locais. Entrevistas semi-estruturadas e inventários fitossociológicos foram empregados para acessar o efeito do uso antropogênico de espécies arbóreas de matas de galeria em áreas do Pampa brasileiro. Oitenta e quatro informantes foram entrevistados e listaram um total de 43 espécies, pertencentes a 23 famílias botânicas. Quatro categorias de uso foram identificadas para as espécies citadas: lenha, medicamento, alimento e madeira. As três espécies mais importantes foram Blepharocalyx salicifolius, Eugenia uniflora e Salix babilonica. O inventário fitossociológico sugere que a exploração antropogênica da mata de galeria está levando algumas espécies a extinção e/ou ameaça local. Com o objetivo de preservar as matas de galeria, sugere-se a re-avaliação das atitudes das comunidades locais, visando um uso sustentável das matas e o reflorestamento das margens de rios com espécies nativas produtoras de frutos comestíveis, possibilitando a exploração de produtos não-madeireiros, assim como o estabelecimento de animais nestes ambientes.As effect of demographic growth in the last decades, many cities in Southern Brazil experienced a degradation process of conservation areas. In this study, semi-structured interviews and a phytosociological inventory were employed to assess the effect of anthropogenic use of tree species of the gallery forest in the Brazilian Pampa. Eighty-four informants were interviewed and listed a total of 43 tree species, belonging to 23 botanical families. Four categories of use were identified for the referenced species: firewood, medicinal, food and timber. The three most

A microring multimode laser using hollow polymer optical fibre

Indian Academy of Sciences (India)

Dye-doped optical fibre; fibre laser; microcavity; whispering gallery mode. ... Cylindrical microcavities with diameters 155, 340 and 615 m were fabricated from a dye-doped hollow polymer optical fibre preform. ... International School of Photonics, Cochin University of Science and Technology, Kochi 682 022, India ...

Quantum-dot-based integrated non-linear sources

DEFF Research Database (Denmark)

Bernard, Alice; Mariani, Silvia; Andronico, Alessio

2015-01-01

The authors report on the design and the preliminary characterisation of two active non-linear sources in the terahertz and near-infrared range. The former is associated to difference-frequency generation between whispering gallery modes of an AlGaAs microring resonator, whereas the latter...

Upconversion channels in Er3+ ZBLALiP fluoride glass microspheres

NARCIS (Netherlands)

O'Shea, D. G.; Ward, J. M.; Shortt, B. J.; Mortier, M.; Feron, P.; Chormaic, S. Nic

We present results on the realization of a multicolour microspherical glass light source fabricated from the erbium doped fluoride glass ZBLALiP. Whispering gallery mode lasing and upconversion processes give rise to laser and fluorescent emissions at multiple wavelengths from the ultraviolet to the

Rn-Gas Concentration and Working Level Measurements Using SSNTD in Uranium Exploration Galleries Allouga Mine, Sinai, Egypt

International Nuclear Information System (INIS)

Abdel-Monem, A.A.; Hassan, S.F.; Abdel-Kader, F.H.; El-Naggar, A.M.; Essia, H.M.; Abdel-Hafez, A.A.

2008-01-01

Measurements of Rn-gas concentrations and Working Level (WL), were carried out in the U-exploration galleries at El- Allouga Mine, Sinai, Egypt by passive techniques (SSNTD) during the four seasons ( Summer, Fall, Winter and Spring) using four different detector types: CR-39, MK, CN-85 and LR-115.Twenty eight (28) stations were chosen for this purpose reflecting different environmental conditions as measurement sites within the galleries. The Rn-gas concentrations , in the summer period ranged from 25.86 to 44.2 pCi/l in the ventilated stations and from 488.98 to 611.16 pCi/l in the non-ventilated stations. In the fall period , the average Rn-gas concentrations in the ventilated stations ranged from 31.61 to 56.36 pCi/l while in the non-ventilated stations from 457.61 to 621.52 pCi/l. In the winter period, the average Rn-gas concentrations in the ventilated stations ranged from 27.59 to 66.45 pCi/l while in the non- ventilated stations from 499.09 to 603.81 pCi/l. In the spring the Rn-gas concentrations ranged from 30.8 to 46.77 pCi/l in the ventilated stations, whereas, in the non-ventilated stations from 404.06 to 445.18 pCi/l. The (WL), in the summer period, ranged from 0.143 to 0.247 in the ventilated sector and from 4.408 to 5.497 in the non-ventilated stations .In fall, the( WL) ranged from 0.166 to 0.295 in the ventilated stations and from 4.123 to 5.624 in the non-ventilated stations. In the winter, the (WL) ranged from 0.105 to 0.37 in the ventilated stations and from 4.138 to 5.26 in the non-ventilated stations. In the spring, the (WL) in the ventilated stations ranged from 0.152 to 0.241 and from 3.696 to 4.087 in the non-ventilated stations. These results indicate that: i)The low measured Rn gas and (WL) values in the ventilated stations reflect the effect of variations in meteorological conditions on (WL) determination where the air flow carries the Rn-gas before it decays and the daughters are plated onto the SSNTD . ii) The larger ranges for Rn

Dual-cavity mode converter for a fundamental mode output in an over-moded relativistic backward-wave oscillator

Energy Technology Data Exchange (ETDEWEB)

Li, Jiawei; Huang, Wenhua [Department of Electronic Engineering and Information Science, University of Science and Technology of China, Hefei 230027 (China); Science and Technology on High Power Microwave Laboratory, Northwest Institute of Nuclear Technology, Xi' an 710024 (China); Xiao, Renzhen; Bai, Xianchen; Zhang, Yuchuan; Zhang, Xiaowei; Shao, Hao; Chen, Changhua [Science and Technology on High Power Microwave Laboratory, Northwest Institute of Nuclear Technology, Xi' an 710024 (China); Zhu, Qi [Department of Electronic Engineering and Information Science, University of Science and Technology of China, Hefei 230027 (China)

2015-03-16

A dual-cavity TM{sub 02}–TM{sub 01} mode converter is designed for a dual-mode operation over-moded relativistic backward-wave oscillator. With the converter, the fundamental mode output is achieved. Particle-in-cell simulation shows that the efficiency of beam-wave conversion was over 46% and a pureTM{sub 01} mode output was obtained. Effects of end reflection provided by the mode converter were studied. Adequate TM{sub 01} mode feedback provided by the converter enhances conversion efficiency. The distance between the mode converter and extraction cavity critically affect the generation of microwaves depending on the reflection phase of TM{sub 01} mode feedback.

Dual-cavity mode converter for a fundamental mode output in an over-moded relativistic backward-wave oscillator

International Nuclear Information System (INIS)

Li, Jiawei; Huang, Wenhua; Xiao, Renzhen; Bai, Xianchen; Zhang, Yuchuan; Zhang, Xiaowei; Shao, Hao; Chen, Changhua; Zhu, Qi

2015-01-01

A dual-cavity TM 02 –TM 01 mode converter is designed for a dual-mode operation over-moded relativistic backward-wave oscillator. With the converter, the fundamental mode output is achieved. Particle-in-cell simulation shows that the efficiency of beam-wave conversion was over 46% and a pureTM 01 mode output was obtained. Effects of end reflection provided by the mode converter were studied. Adequate TM 01 mode feedback provided by the converter enhances conversion efficiency. The distance between the mode converter and extraction cavity critically affect the generation of microwaves depending on the reflection phase of TM 01 mode feedback

Single-mode fiber laser based on core-cladding mode conversion.

Science.gov (United States)

Suzuki, Shigeru; Schülzgen, Axel; Peyghambarian, N

2008-02-15

A single-mode fiber laser based on an intracavity core-cladding mode conversion is demonstrated. The fiber laser consists of an Er-doped active fiber and two fiber Bragg gratings. One Bragg grating is a core-cladding mode converter, and the other Bragg grating is a narrowband high reflector that selects the lasing wavelength. Coupling a single core mode and a single cladding mode by the grating mode converter, the laser operates as a hybrid single-mode laser. This approach for designing a laser cavity provides a much larger mode area than conventional large-mode-area step-index fibers.

Effect of modes interaction on the resistive wall mode stability

International Nuclear Information System (INIS)

Chen Longxi; Wu Bin

2013-01-01

Effects of modes interaction on the resistive wall mode (RWM) stability are studied. When considering the modes interaction effects, the linear growth rate of the most unstable (3, 1) mode decreases. After linear evolution, the RWM saturates at the nonlinear phase. The saturation can be attributed to flux piling up on the resistive wall. When some modes exist, the (3, 1) mode saturates at lower level compared with single mode evolution. Meanwhile, the magnetic energy of the (5, 2) mode increases correspondingly, but the magnetic energy saturation level of the (2, 1) mode changes weakly. (authors)

Scaling Fiber Lasers to Large Mode Area: An Investigation of Passive Mode-Locking Using a Multi-Mode Fiber.

Science.gov (United States)

Ding, Edwin; Lefrancois, Simon; Kutz, Jose Nathan; Wise, Frank W

2011-01-01

The mode-locking of dissipative soliton fiber lasers using large mode area fiber supporting multiple transverse modes is studied experimentally and theoretically. The averaged mode-locking dynamics in a multi-mode fiber are studied using a distributed model. The co-propagation of multiple transverse modes is governed by a system of coupled Ginzburg-Landau equations. Simulations show that stable and robust mode-locked pulses can be produced. However, the mode-locking can be destabilized by excessive higher-order mode content. Experiments using large core step-index fiber, photonic crystal fiber, and chirally-coupled core fiber show that mode-locking can be significantly disturbed in the presence of higher-order modes, resulting in lower maximum single-pulse energies. In practice, spatial mode content must be carefully controlled to achieve full pulse energy scaling. This paper demonstrates that mode-locking performance is very sensitive to the presence of multiple waveguide modes when compared to systems such as amplifiers and continuous-wave lasers.

EZG08 project: acoustic experiments to monitor the EDZ during the gallery excavation process in the Mont Terri Underground Research Laboratory (Switzerland)

International Nuclear Information System (INIS)

Le Gonidec, Y.; Kergosien, B.; Schubnel, A.; Gueguen, Y.; Wassermann, J.; Gibert, D.; Sarout, J.; Nussbaum, C.

2010-01-01

Document available in extended abstract form only. In the Underground Research Laboratory (URL) at Mont Terri, a new gallery G08 was planned to be excavated in 2008 following an original process: the excavation process allowed to monitor the Excavation Damaged Zone (EDZ) from geophysical measurements designed and installed at the end of face of the EZ-G04 gallery during the excavation from the other side, i.e. the end face of the EZ-G08 gallery. The objectives of the project concern spatio-temporal changes of the EDZ: among the methodological developments adapted for the EZG08 project to provide complementary information, acoustic experiments have been prepared in horizontal boreholes to perform the continuous acoustic monitoring of the Excavation Damaged Zone (EDZ). The acoustic measurements, performed on acoustic arrays of several receivers, have been recorded during one month, following two main steps: - Active acoustic surveys: a source is introduced in a central borehole (BEZG5) allowing tomography experiments in the far field and in the near field, i.e. close to and far from BEZG5, respectively. - Acoustic emissions: during the excavation process, numerous acoustic emissions can be detected and associated to micro-seismic events due to rapid crack propagation, generated by the rock relaxation, or simply associated to the excavation process. From the tomography measurements, the acoustic wave velocity field can be estimated, with P and S-wave velocities roughly equal to 2500 m/s-3500 m/s, and 1500 m/s, respectively. The acoustic setup does not show variations of P-wave velocity during the campaign, but spatial variations which could be associated to anisotropic elastic properties of the rock with the maximum P-wave velocities close to the bedding plane. An original method based on a multifrequency approach puts in evidence a frequency dependence of the velocity, with a striking phenomena since the wave velocity decreases with increasing frequency. This effect

Microring Diode Laser for THz Generation

DEFF Research Database (Denmark)

Mariani, S.; Andronico, A.; Favero, I.

2013-01-01

We report on the modeling and optical characterization of AlGaAs/InAs quantum-dot microring diode lasers designed for terahertz (THz) difference frequency generation (DFG) between two whispering gallery modes (WGMs) around 1.3 $\\mu$m. In order to investigate the spectral features of this active...

Method of cutting steeply falling coal beds. [Bacteria, which only grow on methane, are injected into the coal bed and form low viscosity polysaccharides: as a result the coal collapses into the haulage gallery and is hauled away

Energy Technology Data Exchange (ETDEWEB)

Gretsinger, B Ye; Chernyshenko, D V; Levin, A D; Malashenko, Yu R; Shinkovskiy, V A; Shurova, Z P; Volkov, V I

1982-01-01

The purpose of the invention is to reduce outlays for collapse and output of coal by creating artificial cavities of sliding along the coal bed in the surrounding rocks. This goal is achieved because in the well drilled in the bed for the entire height of the level, a suspension of cells of methane-oxidizing microorganisms is injected. The methane-oxidizing microorganisms used are, for example, the thermophilic culture Methylococcus thermophilus of strains ShP which grow at 45-65/sup 0/ C, or the mesophilic culture Methanomonas rubna of strains 15 Sh growing at 20-37/sup 0/ C. As a result of the vital activity of these cultures, polysaccharides are formed with viscosity of 5-7 and 3-4 St respectively. The mine pressure disrupts the blocks between the wells, and the outline section of the steeply dropping coal bed, being destroyed, slides on the products of vital activity of the microorganisms to the haulage gallery. Then the coal drops on cross cuts to the field gallery through which it is transported. Studies established that the only coal substrate which is suitable for growth of these microorganism cultures is methane. The synthesis of one g of absolutely dry substance of these microorganism requires 1.78 g of methane and 4.7 g of oxygen. The cultures are resistant to hydrostatic pressure from 20 to 150 atm and short-term pressure of gradient drops which occur during injection of the cellular suspension into the coal bed. They are filtered through the coal with preservation of the oxidizing and reproductive properties and are cultivated on the methane contained in the bed and form considerable number of exopolysaccarides. The polysaccarides weaken the bond between the bed and the surrounding rocks and serve as a unique lubricant promoting the sliding towards the haulage gallery of the coal blocks destroyed by mine pressure.

Adiabatic tapered optical fiber fabrication for exciting whispering gallery modes in microcavities

Science.gov (United States)

Chenari, Z.; Latifi, H.; Hashemi, R. S.; Doroudmand, F.

2014-05-01

This article demonstrates an investigation and analysis of a tapered fiber fabrication using an etchant droplet method. To achieve precise control on process, a two-step etching method is proposed (using 48% concentration of HF acid and Buffered HF) which results in low-loss adiabatic tapered fiber. A spectrum analysis monitoring in addition to a microscopy system was used to verify the etching progress. Tapers with losses less than 0.4 dB in air and 4.5 dB in water are demonstrated. A biconical fiber taper fabricated using this method was used to excite the WGMs on a microsphere surface in aquatic environment.

Transverse multibunch modes for non-rigid bunches, including mode coupling

Energy Technology Data Exchange (ETDEWEB)

Berg, J S; Ruth, R D [Stanford Linear Accelerator Center, Menlo Park, CA (United States)

1996-08-01

A method for computing transverse multibunch growth rates and frequency shifts in rings, which has been described previously, is applied to the PEP-II B factory. The method allows multibunch modes with different internal-bunch oscillation modes to couple to one another, similar to single-bunch mode coupling. Including coupling between the multibunch modes gives effects similar to those seen in single-bunch mode coupling. These effects occur at currents that are lower than the single-bunch mode coupling threshold. (author)

H-mode physics

International Nuclear Information System (INIS)

Itoh, Sanae.

1991-06-01

After the discovery of the H-mode in ASDEX ( a tokamak in Germany ) the transition between the L-mode ( Low confinement mode ) and H-mode ( High confinement mode ) has been observed in many tokamaks in the world. The H-mode has made a breakthrough in improving the plasma parameters and has been recognized to be a universal phenomena. Since its discovery, the extensive studies both in experiments and in theory have been made. The research on H-mode has been casting new problems of an anomalous transport across the magnetic surface. This series of lectures will provide a brief review of experiments for explaining H-mode and a model theory of H-mode transition based on the electric field bifurcation. If the time is available, a new theoretical model of the temporal evolution of the H-mode will be given. (author)

Mode-to-mode energy transfers in convective patterns

Indian Academy of Sciences (India)

Abstract. We investigate the energy transfer between various Fourier modes in a low- dimensional model for thermal convection. We have used the formalism of mode-to-mode energy transfer rate in our calculation. The evolution equations derived using this scheme is the same as those derived using the hydrodynamical ...

Effects of mode coupling between low-mode radiation flux asymmetry and intermediate-mode ablator roughness on ignition capsule implosions

Directory of Open Access Journals (Sweden)

Jianfa Gu

2017-01-01

Full Text Available The low-mode shell asymmetry and high-mode hot spot mixing appear to be the main reasons for the performance degradation of the National Ignition Facility (NIF implosion experiments. The effects of the mode coupling between low-mode P2 radiation flux asymmetry and intermediate-mode L = 24 capsule roughness on the implosion performance of ignition capsule are investigated by two-dimensional radiation hydrodynamic simulations. It is shown that the amplitudes of new modes generated by the mode coupling are in good agreement with the second-order mode coupling equation during the acceleration phase. The later flow field not only shows large areal density P2 asymmetry in the main fuel, but also generates large-amplitude spikes and bubbles. In the deceleration phase, the increasing mode coupling generates more new modes, and the perturbation spectrum on the hot spot boundary is mainly from the strong mode interactions rather than the initial perturbation conditions. The combination of the low-mode and high-mode perturbations breaks up the capsule shell, resulting in a significant reduction of the hot spot temperature and implosion performance.

Continuous-Wave Operation of a Frequency-Tunable 460-GHz Second-Harmonic Gyrotron for Enhanced Nuclear Magnetic Resonance

Science.gov (United States)

Torrezan, Antonio C.; Han, Seong-Tae; Mastovsky, Ivan; Shapiro, Michael A.; Sirigiri, Jagadishwar R.; Temkin, Richard J.; Griffin, Robert G.; Barnes, Alexander B.

2012-01-01

The design, operation, and characterization of a continuous-wave (CW) tunable second-harmonic 460-GHz gyrotron are reported. The gyrotron is intended to be used as a submillimeter-wave source for 700-MHz nuclear magnetic resonance experiments with sensitivity enhanced by dynamic nuclear polarization. The gyrotron operates in the whispering-gallery mode TE11,2 and has generated 16 W of output power with a 13-kV 100-mA electron beam. The start oscillation current measured over a range of magnetic field values is in good agreement with theoretical start currents obtained from linear theory for successive high-order axial modes TE11,2,q. The minimum start current is 27 mA. Power and frequency tuning measurements as a function of the electron cyclotron frequency have also been carried out. A smooth frequency tuning range of 1 GHz was obtained for the operating second-harmonic mode either by magnetic field tuning or beam voltage tuning. Long-term CW operation was evaluated during an uninterrupted period of 48 h, where the gyrotron output power and frequency were kept stable to within ±0.7% and ±6 ppm, respectively, by a computerized control system. Proper operation of an internal quasi-optical mode converter implemented to transform the operating whispering-gallery mode to a Gaussian-like beam was also verified. Based on the images of the gyrotron output beam taken with a pyroelectric camera, the Gaussian-like mode content of the output beam was computed to be 92% with an ellipticity of 12%. PMID:23761938

PLC-based LP₁₁ mode rotator for mode-division multiplexing transmission.

Science.gov (United States)

Saitoh, Kunimasa; Uematsu, Takui; Hanzawa, Nobutomo; Ishizaka, Yuhei; Masumoto, Kohei; Sakamoto, Taiji; Matsui, Takashi; Tsujikawa, Kyozo; Yamamoto, Fumihiko

2014-08-11

A PLC-based LP11 mode rotator is proposed. The proposed mode rotator is composed of a waveguide with a trench that provides asymmetry of the waveguide. Numerical simulations show that converting LP11a (LP11b) mode to LP11b (LP11a) mode can be achieved with high conversion efficiency (more than 90%) and little polarization dependence over a wide wavelength range from 1450 nm to 1650 nm. In addition, we fabricate the proposed LP11 mode rotator using silica-based PLC. It is confirmed that the fabricated mode rotator can convert LP11a mode to LP11b mode over a wide wavelength range.

Etude théorique et expérimentale des résonances de galerie de microsphères de silice: pièges à photons pour des expériences d'électrodynamique en cavité

OpenAIRE

Collot , Laurent

1994-01-01

This thesis is devoted to the study of very high Q whispering gallery modes in silica microspheres, about 100μm in diameter. For these resonances the electromagnetic field propagates along an equatorial surface ring with tranverse dimensions of the order of the wavelength. These guided modes have very low losses. They exhibit a remarkable combination of strong localization of the field in a small volume and very long storage times for the photons. These two properties render these microsphere...

Effects of multiple modes interaction on the resistive wall mode instability

International Nuclear Information System (INIS)

Chen, Longxi; Lei, Wenqing; Ma, Zhiwei; Wu, Bin

2013-01-01

The effects of multiple modes interaction on the resistive wall mode (RWM) are studied in a slab geometry with and without plasma flow. The modes interaction can have a large effect on both the linear growth rate and the nonlinear saturation level of the RWM. We found that modes interaction can suppress the linear growth rate for the most unstable mode. The plasma flow can also help to control the growth of the RWM. The RWM can be stabilized completely by a plasma flow when considering the modes interaction. The effect of modes interaction on the RWM is stronger for the mode rational surface in the vacuum than that in the plasma. The modes interaction results in a substantially lowered saturation level for the most unstable RWM. (paper)

Quantum-dot micropillars for parametric THz emission

DEFF Research Database (Denmark)

Mariani, S.; Andronico, A.; Favero, I.

2013-01-01

We report on the design, fabrication and optical investigation of AlGaAs microcavities for THz Difference Frequency Generation (DFG) between Whispering Gallery Modes (WGMs), where the pump and DFG wavelengths (λ ≈ 1.3 μm and λ ≈ 75-150 μm, respectively) lie on opposite sides of the Restrahlen band....... For the pump modes, we demonstrate CW lasing of quantum-dot layers under electrical injection at room temperature. We control the number of lasing WGMs via vertical notches on the pillars sidewalls, providing a selection mechanism for funneling the power only to the modes contributing to DFG. In parallel...

Ballooning modes or Fourier modes in a toroidal plasma?

International Nuclear Information System (INIS)

Connor, J.W.; Taylor, J.B.

1987-01-01

The relationship between two different descriptions of eigenmodes in a torus is investigated. In one the eigenmodes are similar to Fourier modes in a cylinder and are highly localized near a particular rational surface. In the other they are the so-called ballooning modes that extend over many rational surfaces. Using a model that represents both drift waves and resistive interchanges the transition from one of these structures to the other is investigated. In this simplified model the transition depends on a single parameter which embodies the competition between toroidal coupling of Fourier modes (which enhances ballooning) and variation in frequency of Fourier modes from one rational surface to another (which diminishes ballooning). As the coupling is increased each Fourier mode acquires a sideband on an adjacent rational surface and these sidebands then expand across the radius to form the extended mode described by the conventional ballooning mode approximation. This analysis shows that the ballooning approximation is appropriate for drift waves in a tokamak but not for resistive interchanges in a pinch. In the latter the conventional ballooning effect is negligible but they may nevertheless show a ballooning feature. This is localized near the same rational surface as the primary Fourier mode and so does not lead to a radially extended structure

Single-Mode VCSELs

Science.gov (United States)

Larsson, Anders; Gustavsson, Johan S.

The only active transverse mode in a truly single-mode VCSEL is the fundamental mode with a near Gaussian field distribution. A single-mode VCSEL produces a light beam of higher spectral purity, higher degree of coherence and lower divergence than a multimode VCSEL and the beam can be more precisely shaped and focused to a smaller spot. Such beam properties are required in many applications. In this chapter, after discussing applications of single-mode VCSELs, we introduce the basics of fields and modes in VCSELs and review designs implemented for single-mode emission from VCSELs in different materials and at different wavelengths. This includes VCSELs that are inherently single-mode as well as inherently multimode VCSELs where higher-order modes are suppressed by mode selective gain or loss. In each case we present the current state-of-the-art and discuss pros and cons. At the end, a specific example with experimental results is provided and, as a summary, the most promising designs based on current technologies are identified.

High tunability and superluminescence in InAs mid-infrared light emitting diodes

International Nuclear Information System (INIS)

Sherstnev, V.V.; Krier, A.; Hill, G.

2002-01-01

We report on the observation of super luminescence and high spectral current tunability (181 nm) of InAs light emitting diodes operating at 3.0 μm. The source is based on an optical whispering gallery mode which is generated near the edges of the mesa and which is responsible for the superluminescence. (author)

Gallery forest restoration by the attainment of carbon credit: a social-environmental proposal for low-income community

International Nuclear Information System (INIS)

Coelho, Maria Carolina Crisci

2007-01-01

Due to intensification in climate changes by anthropogenic causes, to the recognition of the environmental importance of the Gallery Forest and its intense degradation, this work presents an analysis of the possibilities of carbon credit attainment by low-income community, as part of an incentive program for the restoration of these areas. Two ways are demonstrated: projects of Clean Development Mechanism (CDM), in the scope of the Kyoto Protocol, that generate credits called certified emission reductions; and projects based on voluntary scheme, that generate voluntary emission reductions. Both are difficult to organize and implement. For example: the eligibility of an area, baseline study, monitoring, non-permanence risks of storage carbon, technical and operational structures, operational and business costs, regulated market in consolidation and guarantee of credit acquisition. Nevertheless, this second market presents greater flexibility and acceptance for the forest projects. The social-environmental benefits of these projects are significant and the valuation of their environmental services can revert in financial incentives for low-income community, since that adequately remunerated. The carbon credit can help in the implementation of these projects, contributing for local restoration of the areas and also for carbon capture by the atmosphere, which this is a global subject. (author)

Micro-CTvlab: A web based virtual gallery of biological specimens using X-ray microtomography (micro-CT).

Science.gov (United States)

Keklikoglou, Kleoniki; Faulwetter, Sarah; Chatzinikolaou, Eva; Michalakis, Nikitas; Filiopoulou, Irene; Minadakis, Nikos; Panteri, Emmanouela; Perantinos, George; Gougousis, Alexandros; Arvanitidis, Christos

2016-01-01

During recent years, X-ray microtomography (micro-CT) has seen an increasing use in biological research areas, such as functional morphology, taxonomy, evolutionary biology and developmental research. Micro-CT is a technology which uses X-rays to create sub-micron resolution images of external and internal features of specimens. These images can then be rendered in a three-dimensional space and used for qualitative and quantitative 3D analyses. However, the online exploration and dissemination of micro-CT datasets are rarely made available to the public due to their large size and a lack of dedicated online platforms for the interactive manipulation of 3D data. Here, the development of a virtual micro-CT laboratory (Micro-CT vlab ) is described, which can be used by everyone who is interested in digitisation methods and biological collections and aims at making the micro-CT data exploration of natural history specimens freely available over the internet. The Micro-CT vlab offers to the user virtual image galleries of various taxa which can be displayed and downloaded through a web application. With a few clicks, accurate, detailed and three-dimensional models of species can be studied and virtually dissected without destroying the actual specimen. The data and functions of the Micro-CT vlab can be accessed either on a normal computer or through a dedicated version for mobile devices.

Lead-silicate glass optical microbubble resonator

Energy Technology Data Exchange (ETDEWEB)

Wang, Pengfei, E-mail: pengfei.wang@dit.ie [Photonics Research Centre, Dublin Institute of Technology, Kevin Street, Dublin 8 (Ireland); Optoelectronics Research Centre, University of Southampton, Southampton SO17 1BJ (United Kingdom); Ward, Jonathan; Yang, Yong; Chormaic, Síle Nic [Light-Matter Interactions Unit, OIST Graduate University, 1919-1 Tancha, Onna-son, Okinawa 904-0495 (Japan); Feng, Xian; Brambilla, Gilberto [Optoelectronics Research Centre, University of Southampton, Southampton SO17 1BJ (United Kingdom); Farrell, Gerald [Photonics Research Centre, Dublin Institute of Technology, Kevin Street, Dublin 8 (Ireland)

2015-02-09

Microbubble whispering gallery resonators have the potential to become key components in a variety of active and passive photonic circuit devices by offering a range of significant functionalities. Here, we report on the fabrication, optical characterization, and theoretical analysis of lead-silicate glass and optical microbubble resonators. Evanescent field coupling to the microbubbles was achieved using a 1 μm diameter, silica microfiber at a wavelength of circa 775 nm. High Q-factor modes were efficiently excited in both single-stem and two-stem, lead-silicate glass, and microbubble resonators, with bubble diameters of 38 μm (single-stem) and 48 μm (two-stem). Whispering gallery mode resonances with Q-factors as high as 2.3 × 10{sup 5} (single-stem) and 7 × 10{sup 6} (two-stem) were observed. By exploiting the high-nonlinearity of the lead-silicate glass, this work will act as a catalyst for studying a range of nonlinear optical effects in microbubbles, such as Raman scattering and four-wave mixing, at low optical powers.

Streaming tearing mode

Science.gov (United States)

Shigeta, M.; Sato, T.; Dasgupta, B.

1985-01-01

The magnetohydrodynamic stability of streaming tearing mode is investigated numerically. A bulk plasma flow parallel to the antiparallel magnetic field lines and localized in the neutral sheet excites a streaming tearing mode more strongly than the usual tearing mode, particularly for the wavelength of the order of the neutral sheet width (or smaller), which is stable for the usual tearing mode. Interestingly, examination of the eigenfunctions of the velocity perturbation and the magnetic field perturbation indicates that the streaming tearing mode carries more energy in terms of the kinetic energy rather than the magnetic energy. This suggests that the streaming tearing mode instability can be a more feasible mechanism of plasma acceleration than the usual tearing mode instability.

Competition and evolution of dielectric waveguide mode and plasmonic waveguide mode

Science.gov (United States)

Yuan, Sheng-Nan; Fang, Yun-Tuan

2017-10-01

In order to study the coupling and evolution law of the waveguide mode and two plasmonic surface modes, we construct a line defect waveguide based on hexagonal honeycomb plasmonic photonic crystal. Through adjusting the radius of the edge dielectric rods, the competition and evolution behaviors occur between dielectric waveguide mode and plasmonic waveguide mode. There are three status: only plasmonic waveguide modes occur for rA 0.25a; two kinds of modes coexist for 0.09a advantages in achieving slow light.

Effect of desaturation and re-saturation on shale in underground galleries

International Nuclear Information System (INIS)

Pham, Q.T.

2006-03-01

and re-saturation at the scale of underground facilities are performed with numerical models calibrated with experimental results. Analytical and numerical solutions are found using the finite-elements method to foresee the influence of desaturation and re-saturation on the argillite massif inside the underground galleries. (J.S.)

Soliton Coupling Driven by Phase Fluctuations in Auto-Parametric Resonance

CERN Document Server

Binder, B

2002-01-01

In this paper the interaction of sine-Gordon solitons and mediating linear waves is modelled by a special case of auto-parametric resonance, the Rayleigh-type self-excited non-linear autonomous system driven by a statistical phase gradient related to the soliton energy. Spherical symmetry can stimulate "whispering gallery modes" (WGM) with integral coupling number M=137.

EIT in resonator chains: similarities and differences with atomic media

Science.gov (United States)

Matsko, A. B.; Maleki, L.; Savchenkov, A. A.; Ilchenko, V. S.

2004-01-01

We theoretically study a parallel configuration of two interacting whispering gallery mode optical resonators and show a narrow-band modal structure as a basis for a widely tunable delay line. For the optimum coupling configuration the system can possess an unusually narrow spectral feature with a much narrower bandwidth than the loaded bandwidth of each individual resonator.

Adaptive variational mode decomposition method for signal processing based on mode characteristic

Science.gov (United States)

Lian, Jijian; Liu, Zhuo; Wang, Haijun; Dong, Xiaofeng

2018-07-01

Variational mode decomposition is a completely non-recursive decomposition model, where all the modes are extracted concurrently. However, the model requires a preset mode number, which limits the adaptability of the method since a large deviation in the number of mode set will cause the discard or mixing of the mode. Hence, a method called Adaptive Variational Mode Decomposition (AVMD) was proposed to automatically determine the mode number based on the characteristic of intrinsic mode function. The method was used to analyze the simulation signals and the measured signals in the hydropower plant. Comparisons have also been conducted to evaluate the performance by using VMD, EMD and EWT. It is indicated that the proposed method has strong adaptability and is robust to noise. It can determine the mode number appropriately without modulation even when the signal frequencies are relatively close.

Guaranteed performance in reaching mode of sliding mode ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

addresses the design of constant plus proportional rate reaching law-based SMC for second-order ... Reaching mode; sliding mode controlled systems; output tracking ... The uncertainty in the input distribution function g is expressed as.

High-mode-number ballooning modes in a heliotron/torsatron system. II. Stability

International Nuclear Information System (INIS)

Nakajima, N.

1996-01-01

In heliotron/torsatron systems that have a large Shafranov shift, the local magnetic shear is found to have no stabilizing effect on high-mode-number ballooning modes at the outer side of the torus, even in the region where the global shear is stellarator-like in nature. The disappearance of this stabilization, in combination with the compression of the flux surfaces at the outer side of the torus, leads at relatively low values of the plasma pressure to significant modifications of the stabilizing effect due to magnetic field-line bending on high-mode-number ballooning modes-specifically, that the field-line bending stabilization can be remarkably suppressed or enhanced. In an equilibrium that is slightly Mercier-unstable or completely Mercier-stable due to peaked pressure profiles, such as those used in standard stability calculations, high-mode-number ballooning modes are destabilized due to these modified stability effects, with their eigenfunctions highly localized along the field line. Highly localized mode structures such as these cause the ballooning mode eigenvalues ω 2 to have a strong field line dependence (i.e., α-variation) through the strong dependence of the local magnetic curvature, such that the level surfaces of ω 2 (ψ,θ k ,α) (≤0) become spheroids in (ψ,θ k ,α) space, where ψ labels flux surfaces and θ k is the radial wave number. Because the spheroidal level surfaces for unstable eigenvalues are surrounded by level surfaces for stable eigenvalues of high-mode-number toroidal Alfvacute en eigenmodes, those high-mode-number ballooning modes never lead to low-mode-number modes. In configuration space, these high-mode-number modes are localized in a single toroidal pitch of the helical coils, and hence they may experience substantial stabilization due to finite Larmor radius effects. copyright 1996 American Institute of Physics

Edge-localized mode avoidance and pedestal structure in I-mode plasmas

Energy Technology Data Exchange (ETDEWEB)

Walk, J. R., E-mail: jrwalk@psfc.mit.edu; Hughes, J. W.; Hubbard, A. E.; Terry, J. L.; Whyte, D. G.; White, A. E.; Baek, S. G.; Reinke, M. L.; Theiler, C.; Churchill, R. M.; Rice, J. E. [MIT Plasma Science and Fusion Center, Cambridge, MA 02139-4307 (United States); Snyder, P. B.; Osborne, T. [General Atomics, San Diego, CA 92186-5608 (United States); Dominguez, A [Princeton Plasma Physics Laboratory, Princeton, NJ 08543-0451 (United States); Cziegler, I. [UCSD Center for Momentum Transport and Flow Organization, La Jolla, CA 92093-0417 (United States)

2014-05-15

I-mode is a high-performance tokamak regime characterized by the formation of a temperature pedestal and enhanced energy confinement, without an accompanying density pedestal or drop in particle and impurity transport. I-mode operation appears to have naturally occurring suppression of large Edge-Localized Modes (ELMs) in addition to its highly favorable scalings of pedestal structure and overall performance. Extensive study of the ELMy H-mode has led to the development of the EPED model, which utilizes calculations of coupled peeling-ballooning MHD modes and kinetic-ballooning mode (KBM) stability limits to predict the pedestal structure preceding an ELM crash. We apply similar tools to the structure and ELM stability of I-mode pedestals. Analysis of I-mode discharges prepared with high-resolution pedestal data from the most recent C-Mod campaign reveals favorable pedestal scalings for extrapolation to large machines—pedestal temperature scales strongly with power per particle P{sub net}/n{sup ¯}{sub e}, and likewise pedestal pressure scales as the net heating power (consistent with weak degradation of confinement with heating power). Matched discharges in current, field, and shaping demonstrate the decoupling of energy and particle transport in I-mode, increasing fueling to span nearly a factor of two in density while maintaining matched temperature pedestals with consistent levels of P{sub net}/n{sup ¯}{sub e}. This is consistent with targets for increased performance in I-mode, elevating pedestal β{sub p} and global performance with matched increases in density and heating power. MHD calculations using the ELITE code indicate that I-mode pedestals are strongly stable to edge peeling-ballooning instabilities. Likewise, numerical modeling of the KBM turbulence onset, as well as scalings of the pedestal width with poloidal beta, indicates that I-mode pedestals are not limited by KBM turbulence—both features identified with the trigger for large ELMs

Low-bending loss and single-mode operation in few-mode optical fiber

Science.gov (United States)

Yin, Ping; Wang, Hua; Chen, Ming-Yang; Wei, Jin; Cai, Zhi-Min; Li, Lu-Ming; Yang, Ji-Hai; Zhu, Yuan-Feng

2016-10-01

The technique of eliminating the higher-order modes in a few-mode optical fiber is proposed. The fiber is designed with a group of defect modes in the cladding. The higher-order modes in the fiber can be eliminated by bending the fiber to induce strong coupling between the defect modes and the higher-order modes. Numerical simulation shows the bending losses of the LP01 mode are lower than 1.5×10-4 dB/turn for the wavelength shorter than 1.625 μm. The proposed fiber can be bent multiple turns at small bending radius which are preferable for FTTH related applications.

Plasma Modes

Science.gov (United States)

Dubin, D. H. E.

This chapter explores several aspects of the linear electrostatic normal modes of oscillation for a single-species non-neutral plasma in a Penning trap. Linearized fluid equations of motion are developed, assuming the plasma is cold but collisionless, which allow derivation of the cold plasma dielectric tensor and the electrostatic wave equation. Upper hybrid and magnetized plasma waves in an infinite uniform plasma are described. The effect of the plasma surface in a bounded plasma system is considered, and the properties of surface plasma waves are characterized. The normal modes of a cylindrical plasma column are discussed, and finally, modes of spheroidal plasmas, and finite temperature effects on the modes, are briefly described.

An automatic mode-locked system for passively mode-locked fiber laser

Science.gov (United States)

Li, Sha; Xu, Jun; Chen, Guoliang; Mei, Li; Yi, Bo

2013-12-01

This paper designs and implements one kind of automatic mode-locked system. It can adjust a passively mode-locked fiber laser to keep steady mode-locked states automatically. So the unsteadiness of traditional passively mode-locked fiber laser can be avoided. The system transforms optical signals into electrical pulse signals and sends them into MCU after processing. MCU calculates the frequency of the signals and judges the state of the output based on a quick judgment algorithm. A high-speed comparator is used to check the signals and the comparison voltage can be adjusted to improve the measuring accuracy. Then by controlling two polarization controllers at an angle of 45degrees to each other, MCU extrudes the optical fibers to change the polarization until it gets proper mode-locked output. So the system can continuously monitor the output signal and get it back to mode-locked states quickly and automatically. States of the system can be displayed on the LCD and PC. The parameters of the steady mode-locked states can be stored into an EEPROM so that the system will get into mode-locked states immediately next time. Actual experiments showed that, for a 6.238MHz passively mode-locked fiber lasers, the system can get into steady mode-locked states automatically in less than 90s after starting the system. The expected lock time can be reduced to less than 20s after follow up improvements.

Stability and time-domain analysis of the dispersive tristability in microresonators under modal coupling

Science.gov (United States)

Dumeige, Yannick; Féron, Patrice

2011-10-01

Coupled nonlinear resonators have potential applications for the integration of multistable photonic devices. The dynamic properties of two coupled-mode nonlinear microcavities made of Kerr material are studied by linear stability analysis. Using a suitable combination of the modal coupling rate and the frequency detuning, it is possible to obtain configurations where a hysteresis loop is included inside other bistable cycles. We show that a single resonator with two modes both linearly and nonlinearly coupled via the cross-Kerr effect can have a multistable behavior. This could be implemented in semiconductor nonlinear whispering-gallery-mode microresonators under modal coupling for all optical signal processing or ternary optical logic applications.

Stability and time-domain analysis of the dispersive tristability in microresonators under modal coupling

International Nuclear Information System (INIS)

Dumeige, Yannick; Feron, Patrice

2011-01-01

Coupled nonlinear resonators have potential applications for the integration of multistable photonic devices. The dynamic properties of two coupled-mode nonlinear microcavities made of Kerr material are studied by linear stability analysis. Using a suitable combination of the modal coupling rate and the frequency detuning, it is possible to obtain configurations where a hysteresis loop is included inside other bistable cycles. We show that a single resonator with two modes both linearly and nonlinearly coupled via the cross-Kerr effect can have a multistable behavior. This could be implemented in semiconductor nonlinear whispering-gallery-mode microresonators under modal coupling for all optical signal processing or ternary optical logic applications.

Evidence of dilute ferromagnetism in rare-earth doped yttrium aluminium garnet

Energy Technology Data Exchange (ETDEWEB)

Farr, Warrick G.; Goryachev, Maxim; Le Floch, Jean-Michel; Tobar, Michael E. [ARC Centre of Excellence for Engineered Quantum Systems, University of Western Australia, 35 Stirling Highway, Crawley, Western Australia 6009 (Australia); Bushev, Pavel [Experimentalphysik, Universität des Saarlandes, D-66123 Saarbrücken (Germany)

2015-09-21

This work demonstrates strong coupling regime between an erbium ion spin ensemble and microwave hybrid cavity-whispering gallery modes in a yttrium aluminium garnet dielectric crystal. Coupling strengths of 220 MHz and mode quality factors in excess of 10{sup 6} are demonstrated. Moreover, the magnetic response of high-Q modes demonstrates behaviour which is unusual for paramagnetic systems. This behaviour includes hysteresis and memory effects. Such qualitative change of the system's magnetic field response is interpreted as a phase transition of rare earth ion impurities. This phenomenon is similar to the phenomenon of dilute ferromagnetism in semiconductors. The clear temperature dependence of the phenomenon is demonstrated.

Stability of longitudinal modes in a bunched beam with mode coupling

International Nuclear Information System (INIS)

Satoh, K.

1981-06-01

In this paper we study a longitudinal coherent bunch instability in which the growth time is comparable to or less than the period of synchrotron oscillations. Both longitudinal and transverse bunch instabilities have been studied. In most treatments, however, the coherent force is assumed to be small and is treated as a perturbation compared with the synchrotron force. This makes the problem simpler because an individual synchrotron mode is decoupled. As bunch current increases, the coherent force is no longer small and the mode frequency shift becomes significant compared with the synchrotron frequency. Therefore in this case it is necessary to include coupling of the synchrotron modes. Recently a fast blow-up instability which comes from mode coupling was studied. Their method is to derive a dispersion relation for a bunched beam using the Vlasov equation and to analyze it as in a coasting beam. They showed that if mode coupling is included the Vlasov equation predicts a fast microwave instability with a stability condition similar to that for a coasting beam. In this paper we will partly follow their method and present a formalism which includes coupling between higher-order radial modes as well as coupling between synchrotron modes. The formalism is considered to be generalization of the Sacherer formalism without mode coupling. This theory predicts that instability is induced not only by coupling between different synchrotron modes, but also by coupling between positive and negative modes, since negative synchrotron modes are included in the theory in a natural manner. This formalism is to be used for a Gaussian bunch and a parabolic bunch, and is also useful for transverse problems

Double-mode pulsation

International Nuclear Information System (INIS)

Cox, A.N.

1982-01-01

Double mode pulsation is a very pervasive phenomenon in stars all over the Hertzsprung-Russell diagram. In order of increasing radius, examples are: ZZ Ceti stars, the sun, the delta Scuti stars, RR Lyrae variables, the β Cephei variables and those related to them, Cepheids, and maybe even the Mira stars. These many modes have been interpreted as both radial and nonradial modes, but in many cases the actual mode has not been clearly identified. Yellow giants seem to be the most simple pulsators with a large majority of the RR Lyrae variables and Cepheids showing only one pulsation period. We limit this review to those very few cases for classical Cepheids and RR Lyrae variables which display two modes. For these we know many facts about these stars, but the actual cause of the pulsation in two modes simultaneously remains unknown

Inter-comb synchronization by mode-to-mode locking

Science.gov (United States)

Chun, Byung Jae; Kim, Young-Jin; Kim, Seung-Woo

2016-08-01

Two combs of fiber femtosecond lasers are synchronized through the optical frequency reference created by injection-locking of a diode laser to a single comb mode. Maintaining a mHz-level narrow linewidth, the optical frequency reference permits two combs to be stabilized by mode-to-mode locking with a relative stability of 1.52  ×  10-16 at 10 s with a frequency slip of 2.46 mHz. This inter-comb synchronization can be utilized for applications such as dual-comb spectroscopy or ultra-short pulse synthesis without extra narrow-linewidth lasers.

The H-mode Pedestal and Edge Localized Modes in NSTX

International Nuclear Information System (INIS)

Maingi, R.; Fredrickson, E.D.; Menard, J.E.; Nishino, N.; Roquemore, A.L.; Sabbagh, S.A.; Tritz, K.

2004-01-01

The research program of the National Spherical Torus Experiment (NSTX) routinely utilizes the H-mode confinement regime to test and extend beta and pulse length limits. As in conventional aspect ratio tokamaks, NSTX observes a variety of edge localized modes (ELMs) in H-mode. Hence a significant part of the research program is dedicated to ELMs studies

A Minimal Model to Explore the Influence of Distant Modes on Mode-Coupling Instabilities

Science.gov (United States)

Kruse, Sebastian; Hoffmann, Norbert

2010-09-01

The phenomenon of mode-coupling instability is one of the most frequently explored mechanisms to explain self-excited oscillation in sliding systems with friction. A mode coupling instability is usually due to the coupling of two modes. However, further modes can have an important influence on the coupling of two modes. This work extends a well-known minimal model to describe mode-coupling instabilities in order to explore the influence of a distant mode on the classical mode-coupling pattern. This work suggests a new minimal model. The model is explored and it is shown that a third mode can have significant influence on the classical mode-coupling instabilities where two modes are coupling. Different phenomena are analysed and it is pointed out that distant modes can only be ignored in very special cases and that the onset friction-induced oscillations can even be very sensitive to minimal variation of a distant mode. Due to the chosen academic minimal-model and the abandonment of a complex Finite-Element model the insight stays rather phenomenological but a better understanding of the mode-coupling mechnanism can be gained.

Accurate mode characterization of two-mode optical fibers by in-fiber acousto-optics.

Science.gov (United States)

Alcusa-Sáez, E; Díez, A; Andrés, M V

2016-03-07

Acousto-optic interaction in optical fibers is exploited for the accurate and broadband characterization of two-mode optical fibers. Coupling between LP 01 and LP 1m modes is produced in a broadband wavelength range. Difference in effective indices, group indices, and chromatic dispersions between the guided modes, are obtained from experimental measurements. Additionally, we show that the technique is suitable to investigate the fine modes structure of LP modes, and some other intriguing features related with modes' cut-off.

Mode-mode coupling theory of itinerant electron antiferromagnetism in superconducting state

International Nuclear Information System (INIS)

Fujimoto, Yukinobu; Miyake, Kazumasa

2012-01-01

It has been considered since the first discovery of a high-T c cuprate that an antiferromagnetic (AF) state and a superconducting (SC) state are separated in it. However, it is very intriguing that the coexistence of the AF and SC states has recently been observed in HgBa 2 Ca 4 Cu 5 O 12+ (Hg-1245). Moreover, it is very novel that this coexistence of these two states appears if the SC-transition temperature T c is higher than the AF-transition temperature T N . The mode-mode coupling theory can provide a clear elucidation of this novel phenomenon. A key point of this theory is that the AF susceptibility consists of the random-phase-approximation (RPA) term and the mode-mode coupling one. The RPA term works to make a positive contribution to the emergence of the antiferromagnetic critical point (AF-CP). In contrast, the mode-mode coupling term works to make a negative contribution to the emergence of the AF-CP. However, the growth of the SC-gap function in the d x 2 -y 2 -wave SC state works to suppress the negative contribution of the mode-mode coupling term to the emergence of the AF-CP. Moreover, the effect of SC fluctuations near the SC-transition temperature T c suppresses the mode-mode coupling term of the AF susceptibility that works to hinder the AF ordering. For these two reasons, there is a possibility that the d x 2 -y 2 -wave SC state is likely to promote the emergence of the AF-CP. Namely, the appearance of the above-mentioned novel coexistence of the AF and SC states observed in Hg-1245 can be explained qualitatively on the basis of this idea.

A comprehensive spectral theory of zonal-mode dynamics in trapped electron mode turbulence

International Nuclear Information System (INIS)

Terry, P.W.; Gatto, R.; Baver, D.A.; Fernandez, E.

2005-01-01

A comprehensive, self-consistent theory for spectral dynamics in trapped electron mode (TEM) turbulence offers critical new understanding and insights into zonal-mode physics. This theory shows that 1) zonal mode structure, anisotropy, excitation, and temporal behavior arise at and from the interface of nonlinear advection and linear wave properties; 2) waves induce a marked spectral energy-transfer anisotropy that preferentially drives zonal modes relative to non zonal modes; 3) triplet correlations involving density (as opposed to those involving only flow) mediate the dominant energy transfer at long wavelengths; 4) energy transfer becomes inverse in the presence of wave anisotropy, where otherwise it is forward; 5) zonal-mode excitation is accompanied by excitation of a spectrum of damped eigenmodes, making zonal modes nonlinearly damped; and 6) the combination of anisotropic transfer to zonal modes and their nonlinear damping make this the dominant saturation mechanism for TEM turbulence. This accounts for the reduction of turbulence level by zonal modes, not zonal-flow ExB shearing. (author)

Broad spectral response photodetector based on individual tin-doped CdS nanowire

Directory of Open Access Journals (Sweden)

Weichang Zhou

2014-12-01

Full Text Available High purity and tin-doped 1D CdS micro/nano-structures were synthesized by a convenient thermal evaporation method. SEM, EDS, XRD and TEM were used to examine the morphology, composition, phase structure and crystallinity of as-prepared samples. Raman spectrum was used to confirm tin doped into CdS effectively. The effect of impurity on the photoresponse properties of photodetectors made from these as-prepared pure and tin-doped CdS micro/nano-structures under excitation of light with different wavelength was investigated. Various photoconductive parameters such as responsivity, external quantum efficiency, response time and stability were analyzed to evaluate the advantage of doped nanowires and the feasibility for photodetector application. Comparison with pure CdS nanobelt, the tin-doped CdS nanowires response to broader spectral range while keep the excellect photoconductive parameters. Both trapped state induced by tin impurity and optical whispering gallery mode microcavity effect in the doped CdS nanowires contribute to the broader spectral response. The micro-photoluminescence was used to confirm the whispering gallery mode effect and deep trapped state in the doped CdS nanowires.

Modes and Mode Volumes for Leaky Optical Cavities and Plasmonic Nanoresonators

DEFF Research Database (Denmark)

Hughes, Stephen; Kristensen, Philip Trøst

2013-01-01

Electromagnetic cavity modes in photonic and plasmonic resonators offer rich and attractive regimes for tailoring the properties of light–matter interactions, yet there is a disturbing lack of a precise definition for what constitutes a cavity mode, and as a result their mathematical properties r...... methods for quasinormal modes of both photonic and plasmonic resonators and the concept of a generalized effective mode volume, and we illustrate the theory with several representative cavity structures from the fields of photonic crystals and nanoplasmonics....

Nonlinear mode coupling in rotating stars and the r-mode instability in neutron stars

International Nuclear Information System (INIS)

Schenk, A.K.; Arras, P.; Flanagan, E.E.; Teukolsky, S.A.; Wasserman, I.

2002-01-01

We develop the formalism required to study the nonlinear interaction of modes in rotating Newtonian stars, assuming that the mode amplitudes are only mildly nonlinear. The formalism is simpler than previous treatments of mode-mode interactions for spherical stars, and simplifies and corrects previous treatments for rotating stars. At linear order, we elucidate and extend slightly a formalism due to Schutz, show how to decompose a general motion of a rotating star into a sum over modes, and obtain uncoupled equations of motion for the mode amplitudes under the influence of an external force. Nonlinear effects are added perturbatively via three-mode couplings, which suffices for moderate amplitude modal excitations; the formalism is easy to extend to higher order couplings. We describe a new, efficient way to compute the modal coupling coefficients, to zeroth order in the stellar rotation rate, using spin-weighted spherical harmonics. The formalism is general enough to allow computation of the initial trends in the evolution of the spin frequency and differential rotation of the background star. We apply this formalism to derive some properties of the coupling coefficients relevant to the nonlinear interactions of unstable r modes in neutron stars, postponing numerical integrations of the coupled equations of motion to a later paper. First, we clarify some aspects of the expansion in stellar rotation frequency Ω that is often used to compute approximate mode functions. We show that, in zero-buoyancy stars, the rotational modes (those modes whose frequencies vanish as Ω→0) are orthogonal to zeroth order in Ω. From an astrophysical viewpoint, the most interesting result of this paper is that many couplings of r modes to other rotational modes are small: either they vanish altogether because of various selection rules, or they vanish to lowest order in Ω or in compressibility. In particular, in zero-buoyancy stars, the coupling of three r modes is forbidden

Mode group specific amplification length in an asymmetric LPG assisted few-mode EDFA

Science.gov (United States)

Rastogi, Vipul; Gaur, Ankita; Aschieri, Pierre; Dussardier, Bernard

2017-01-01

This article presents a scheme for few-mode EDFA, which allows to choose independent amplification lengths for different mode groups. The EDF is a dual concentric core fiber, where the central core is connected to the line FMF and the ring core is doped with erbium to provide amplification. The modes of FMF are launched into the central core of the EDF, are converted into ring modes using LPG for amplification and then converted back into central core modes using another LPG. The distance between the LPGs determines the amplification length. The amplification length, can thus, be chosen for a given mode group. We demonstrate the working of this concept by choosing LP11 and LP21 mode groups of the FMF and show that a suitable choice of amplification lengths for the two mode groups can tailor the differential modal gain (DMG) to any desired value. We demonstrate achieving zero DMG among all the mode of LP11 and LP21 mode groups using this concept while having gain in excess of 20 dB. The study should be useful for optical fiber communication system employing space-division multiplexing (SDM).

Dual-Mode Combustor

Science.gov (United States)

Trefny, Charles J (Inventor); Dippold, Vance F (Inventor)

2013-01-01

A new dual-mode ramjet combustor used for operation over a wide flight Mach number range is described. Subsonic combustion mode is usable to lower flight Mach numbers than current dual-mode scramjets. High speed mode is characterized by supersonic combustion in a free-jet that traverses the subsonic combustion chamber to a variable nozzle throat. Although a variable combustor exit aperture is required, the need for fuel staging to accommodate the combustion process is eliminated. Local heating from shock-boundary-layer interactions on combustor walls is also eliminated.

Sliding mode control and observation

CERN Document Server

Shtessel, Yuri; Fridman, Leonid; Levant, Arie

2014-01-01

The sliding mode control methodology has proven effective in dealing with complex dynamical systems affected by disturbances, uncertainties and unmodeled dynamics. Robust control technology based on this methodology has been applied to many real-world problems, especially in the areas of aerospace control, electric power systems, electromechanical systems, and robotics. Sliding Mode Control and Observation represents the first textbook that starts with classical sliding mode control techniques and progresses toward newly developed higher-order sliding mode control and observation algorithms and their applications. The present volume addresses a range of sliding mode control issues, including: *Conventional sliding mode controller and observer design *Second-order sliding mode controllers and differentiators *Frequency domain analysis of conventional and second-order sliding mode controllers *Higher-order sliding mode controllers and differentiators *Higher-order sliding mode observers *Sliding mode disturbanc...

Low alkaline cement used in the construction of a gallery in the Horonobe Underground Research Laboratory

International Nuclear Information System (INIS)

Nakayama, Masashi; Sato, Haruo; Sugita, Yutaka; Ito, Seiji; Minamide, Masashi; Kitagawa, Yoshito

2011-01-01

In Japan, any high level radioactive waste (HLW) pos is to be constructed at over 300 m depth below surface. Tunnel support is used for safety during the construction and operation, and shotcrete and concrete lining are used as the tunnel support. Concrete is a composite material comprised of aggregate, cement and various admixtures. Low alkaline cement has been developed for the long term stability of the barrier systems whose performance could be negatively affected by highly alkaline conditions arising due to cement used in a repository. Japan Atomic Energy Agency (JAEA) has developed a low alkaline cement, named as HFSC (Highly Flyash Contained Silicafume Cement), containing over 60wt% of silica-fume (SF) and fly-ash (FA). HFSC was used experimentally as the shotcrete material in construction of part of the 140m deep gallery in the Horonobe Underground Research Laboratory (URL). The objective of this experiment was to assess the performance of HFSC shotcrete in terms of mechanics, workability, durability, and so on. HFSC used in this experiment is composed of 40wt% OPC (Ordinary Portland Cement), 20wt% SF, and 40 wt% FA. This composition was determined based on mechanical testing of various mixes of the above components. Because of the low OPC content, the strength of HFSC tends to be lower than that of OPC. The total length of tunnel using HFSC shotcrete is about 73 m and about 500 m 3 of HESC was used. The workability of HESC shotcrete was confirmed in this experimental construction. (author)

Geophysical monitoring of the EDZ during a gallery excavation in the Opalinus clay of the Mont Terri URL: design and principles of specific in situ experimental setups

International Nuclear Information System (INIS)

Gibert, D.; Maineult, A.; Kergosien, B.; Le Gonidec, Y.; Nicollin, F.; Sarout, J.; Wassermann, J.

2012-01-01

Document available in extended abstract form only. At the Mont Terri Underground Rock Laboratory, the gallery Ga08 was excavated in August 2008 to join the end-face of the pre-existing gallery Ga04. The Excavation Damaged Zone (EDZ) induced during the gallery construction was monitored from the instrumented face of Ga04. The EZ-G08 experiments required original acquisition setups, specifically designed to be installed in small boreholes and to ensure long term measurements. Different geophysical methods have been experimented for the EZ-G08 project and specific design of the experiments were required in order to coordinate multiple and simultaneous acquisitions, including acoustic emission (AE) acquisition setup (16 acoustic receivers), manufacturing of a combined electrical (256 electrodes) and acoustic tomography setup (64 receivers) to be introduced in horizontal boreholes with small diameters (56 mm), design of an acoustic source, design and manufacturing of a combined electrical tomography (64 lead electrodes) and self-potential measurements (64 un-polarizable electrodes). Other arrays of electrodes have also been placed at the end-face of Ga04 (715 inox electrodes and an array of 16 un-polarizable electrodes). The self-potential (SP) monitoring took place in the borehole BEZ-G5 equipped in mid- February 2008 with a specific device on which custom-made electrodes were fixed. To avoid polarisation effect and guaranty a satisfactorily signal-to-noise ratio, SP was measured with 64 un-polarizable electrodes, with an offset of 15 cm made of a metallic wire in chemical equilibrium with a surrounding solution containing a salt of the same metal. The electrical contact between the solution and the natural medium is ensured by a porous material. The electrodes were mounted upward on a half-cylinder fixed onto an inflatable pipe and introduced in BEZ-G5. The internal pipe was inflated to ensure a good electrical contact between the electrodes and the borehole wall. The

Optical transport and statistics of radiative losses in disordered chains of microspheres

International Nuclear Information System (INIS)

Deng Chaosheng; Xu Hui; Deych, Lev

2010-01-01

Optical transport in a one-dimensional chain of microspherical resonators with size disorder is studied in the spectral range of high-Q whispering gallery modes. An ab initio approach is used to develop a theoretical framework for analysis of steady-state transport parameters with main emphasis on properly defined radiative loss coefficient. Probability distribution and scaling properties of the latter are established and explained.

Piscines et plages chez Kundera

DEFF Research Database (Denmark)

Boisen, Jørn

2007-01-01

Swimming pools, stricto sensu, are a newcomer in the gallery of western topoï, linked as they are to 20th century consumer culture. For obvious reasons they have become a recognized cinematographic topos, but - more surprisingly - they have also made their way to novel. For instance you find a lo...... and nihilism in a mode that is much darker and more troubled than one would expect...

Spin valve sensor for biomolecular identification: Design, fabrication, and characterization

Science.gov (United States)

Li, Guanxiong

Biomolecular identification, e.g., DNA recognition, has broad applications in biology and medicine such as gene expression analysis, disease diagnosis, and DNA fingerprinting. Therefore, we have been developing a magnetic biodetection technology based on giant magnetoresistive spin valve sensors and magnetic nanoparticle (developed for the magnetic nanoparticle detection, assuming the equivalent average field of magnetic nanoparticles and the coherent rotation of spin valve free layer magnetization. Micromagnetic simulations have also been performed for the spin valve sensors. The analytical model and micromagnetic simulations are found consistent with each other and are in good agreement with experiments. The prototype spin valve sensors have been fabricated at both micron and submicron scales. We demonstrated the detection of a single 2.8-mum magnetic microbead by micron-sized spin valve sensors. Based on polymer-mediated self-assembly and fine lithography, a bilayer lift-off process was developed to deposit magnetic nanoparticles onto the sensor surface in a controlled manner. With the lift-off deposition method, we have successfully demonstrated the room temperature detection of monodisperse 16-nm Fe3O 4 nanoparticles in a quantity from a few tens to several hundreds by submicron spin valve sensors, proving the feasibility of the nanoparticle detection. As desired for quantitative biodetection, a fairly linear dependence of sensor signal on the number of nanoparticles has been confirmed. The initial detection of DNA hybridization events labeled by magnetic nanoparticles further proved the magnetic biodetection concept.

Propagating annular modes

Science.gov (United States)

Sheshadri, A.; Plumb, R. A.

2017-12-01

The leading "annular mode", defined as the dominant EOF of surface pressure or of zonal mean zonal wind variability, appears as a dipolar structure straddling the mean midlatitude jet and thus seems to describe north-south wobbling of the jet latitude. However, extratropical zonal wind anomalies frequently tend to migrate poleward. This behavior can be described by the first two EOFs, the first (AM1) being the dipolar structure, and the second (AM2) having a tripolar structure centered on the mean jet. Taken in isolation, AM1 thus describes a north-south wobbling of the jet position, while AM2 describes a strengthening and narrowing of the jet. However, despite the fact that they are spatially orthogonal, and their corresponding time series temporally orthogonal, AM1 and AM2 are not independent, but show significant lag-correlations which reveal the propagation. The EOFs are not modes of the underlying dynamical system governing the zonal flow evolution. The true modes can be estimated using principal oscillation pattern (POP) analysis. In the troposphere, the leading POPs manifest themselves as a pair of complex conjugate structures with conjugate eigenvalues thus, in reality, constituting a single, complex, mode that describes propagating anomalies. Even though the principal components associated with the two leading EOFs decay at different rates, each decays faster than the true mode. These facts have implications for eddy feedback and the susceptibility of the mode to external perturbations. If one interprets the annular modes as the modes of the system, then simple theory predicts that the response to steady forcing will usually be dominated by AM1 (with the longest time scale). However, such arguments should really be applied to the true modes. Experiments with a simplified GCM show that climate response to perturbations do not necessarily have AM1 structures. Implications of these results for stratosphere-troposphere interactions are explored. The POP

A dual-mode driver IC with monolithic negative drive-voltage capability and digital current-mode controller for depletion-mode GaN HEMT

NARCIS (Netherlands)

Wen, Y.; Rose, M.; Fernandes, R.; van Otten, R.; Bergveld, H.J.; Trescases, O.

2017-01-01

This work presents a driver and controller integrated circuit (IC) for depletion-mode gallium nitride (GaN) high-electron-mobility transistors (HEMTs). The dual-mode driver can be configured for cascode-drive (CD) or HEMT-drive (HD) mode. In the CD mode, a cascode low-voltage DMOS is driven to

Observations on resistive wall modes

International Nuclear Information System (INIS)

Gerwin, R.A.; Finn, J.M.

1996-01-01

Several results on resistive wall modes and their application to tokamaks are presented. First, it is observed that in the presence of collisional parallel dynamics there is an exact cancellation to lowest order of the dissipative and sound wave effects for an ideal Ohm's law. This is easily traced to the fact that the parallel dynamics occurs along the perturbed magnetic field lines for such electromagnetic modes. Such a cancellation does not occur in the resistive layer of a tearing-like mode. The relevance to models for resistive wall modes using an electrostatic Hammett-Perkins type operator to model Landau damping will be discussed. Second, we observe that with an ideal Ohm's law, resistive wall modes can be destabilized by rotation in that part of parameter space in which the ideal MHD modes are stable with the wall at infinity. This effect can easily be explained by interpreting the resistive wall instability in terms of mode coupling between the backward stable MHD mode and a stable mode locked into the wall. Such an effect can occur for very small rotation for tearing-resistive wall modes in which inertia dominates viscosity in the layer, but the mode is stabilized by further rotation. For modes for which viscosity dominates in the layer, rotation is purely stabilizing. For both tearing models, a somewhat higher rotation frequency gives stability essentially whenever the tearing mode is stable with a perfectly conducting wall. These tearing/resistive wall results axe also simply explained in terms of mode coupling. It has been shown that resonant external ideal modes can be stabilized in the presence of resistive wall and resistive plasma with rotation of order the nominal tearing mode growth rate. We show that these modes behave as resistive wall tearing modes in the sense above. This strengthens the suggestion that rotational stabilization of the external kink with a resistive wall is due to the presence of resistive layers, even for ideal modes

Distributed mode filtering rod fiber amplifier delivering 292W with improved mode stability

DEFF Research Database (Denmark)

Laurila, Marko; Jørgensen, Mette Marie; Hansen, Kristian Rymann

2012-01-01

We demonstrate a high power fiber (85μm core) amplifier delivering up to 292Watts of average output power using a mode-locked 30ps source at 1032nm. Utilizing a single mode distributed mode filter bandgap rod fiber, we demonstrate 44% power improvement before the threshold-like onset of mode inst...

Combined mode I-mode II fracture of 12-mol%-ceria-doped tetragonal zirconia polycrystalline ceramic

International Nuclear Information System (INIS)

Tikare, V.; Choi, S.R.

1997-01-01

The mode I, mode II, and combined mode I-mode II fracture behavior of ceria-doped tetragonal zirconia polycrystalline (Ce-TZP) ceramic was studied. The single-edge-precracked-beam (SEPB) samples were fractured using the asymmetric four-point-bend geometry. The ratio of mode I to mode II loading was varied by varying the degree of asymmetry in the four-point-bend geometry. The minimum strain energy density theory best described the mixed-mode fracture behavior of Ce-TZP with the mode I fracture toughness, K IC = 8.2 ± 0.6 MPa·m 1/2 , and the mode II fracture toughness, K IIC = 8.6 ± 1.3 MPa·m 1/2

Low-frequency modes with high toroidal mode numbers. A general formulation

International Nuclear Information System (INIS)

Pegoraro, F.; Schep, T.J.

1979-09-01

Low-frequency waves with high toroidal mode numbers in an axisymmetric toroidal configuration are studied. In particular, the relationship between the periodicity constraints imposed by the geometry, magnetic shear and the spatial structure of eigenmodes is investigated. By exploiting the radial translational invariance and the poloidal periodicity of the gyrokinetic and Maxwell equations, the two-dimensional problem can be converted into a one-dimensional one and the mode structure can be expressed in terms of a single extended poloidal variable. This representation is used in the description of electromagnetic modes with phase velocities larger than the ion thermal velocity and with frequencies below the ion gyro-frequency. Trapped particle, curvature and compressional effects are retained. The dispersion equations for drift mode and Alfven-type modes are given in general geometry and simplified solutions are presented in the configuration of a double periodic plane slab. (Auth.)

Experimental verification of microbending theory using mode coupling to discrete cladding modes

DEFF Research Database (Denmark)

Probst, C. B.; Bjarklev, Anders Overgaard; Andreasen, S. B.

1989-01-01

a microbending theory in which coupling between the guided mode and a number of discrete cladding modes is considered. Very good agreement between theory and measurement is achieved. The consequences of the existence of discrete cladding modes with regard to the proper choice of artificial microbending spectrum...

Nonlinear drift tearing mode. Strong mode of excitation and stabilization mechanisms

International Nuclear Information System (INIS)

Galeev, A.A.; Zelenyj, L.M.; Kuznetsova, M.M.

1985-01-01

A nonlinear theory of magnetic disturbance development in collisionless configurations with magnetic field shear is considered. The instability evolution is investigated with account for the dynamics of ions and potential electric fields which determine the mode stabilization. It has been found that the drift tearing mode possesses metastable properties: in a nonlinear mode even the growth of linearly stable disturbances of the finite amplitude is possible

Tacoma mode

International Nuclear Information System (INIS)

Courant, E.D.; Ruth, R.D.; Wang, J.M.

1979-01-01

The name Tacoma refers to the Tacoma Narrows Bridge which collapsed on November 8, 1940 due to massive oscillations caused by high winds. One of the destructive modes was a torsion mode which was excited by transverse wind, a dipole force, and continued until the bridge collapsed. The name is used to refer to a coherent mode of oscillation of a spectrum of oscillators in which the amplitude vs frequency graph contains one node, where the node occurs near the driving frequency and a(ω) is not symmetric about zero. When this result is applied to vertical instabilities in coasting beams, it implies the existence of a coherent skew quadrupole moment, whenever a coherent dipole oscillation exists

Coupled-Mode Theory derivation of the formal equivalence between a three-mode waveguide and a set of three mutually coupled single-mode waveguides

Directory of Open Access Journals (Sweden)

Boucher Yann G.

2017-01-01

Full Text Available The formal identification between a two-mode waveguide and a system of two mutually coupled single-mode waveguides stems from the symmetries of the evolution operator. When the gap tends to zero, the super-modes of the coupled system merge continuously into the modes of the multimode waveguide. For modelling purposes, it is very tempting to extend the analogy to three-mode waveguides (and beyond. But not without some precautions…

Field-dependent dynamic responses from dilute magnetic nanoparticle dispersions

DEFF Research Database (Denmark)

Fock, Jeppe; Balceris, Christoph; Costo, Rocio

2018-01-01

The response of magnetic nanoparticles (MNPs) to an oscillating magnetic field outside the linear response region is important for several applications including magnetic hyperthermia, magnetic resonance imaging and biodetection. The size and magnetic moment are two critical parameters for the pe...

L to H-mode Power Threshold and Confinement Characteristics of H-modes in KSTAR

Energy Technology Data Exchange (ETDEWEB)

Kim, H. S.; Na, Y.S., E-mail: ftwalker.hyuns@gmail.com [Seoul National University, Seoul (Korea, Republic of); Ahn, J. W. [Oak Ridge National Laboratory, Oak Ridge (United States); Jeon, Y. M.; Yoon, S. W.; Lee, K. D.; Ko, W. H.; Bae, Y. S.; Kim, W. C.; Kwak, J. G. [National Fusion Research Institute, Daejeon (Korea, Republic of)

2012-09-15

Full text: Since KSTAR has obtained the H-mode in 2010 campaign, H-mode plasmas were routinely obtained with combined heating of NBI with maximum power of 1.5 MW and ECRH with maximum power of {approx} 0.3 MW and {approx} 0.6 MW for 110 GHz and 170 GHz, respectively. The L- to H-mode power threshold and confinement properties of KSTAR H-modes are investigated in this work. Firstly, the L- to H-mode power threshold and the power loss to the seperatrix are calculated by power balance analysis for about collected 400 shots. As a result, a trend of roll-over is observed in the power threshold of KSTAR H-mode compared with the multi-machine power threshold scaling in the low density regime. Dependence of the power threshold on other parameters are also investigated such as the X-point position and shaping parameters like as triangularity and elongation. In addition, the reason of reduction of power threshold in 2011 campaign compared with that in 2010 is addressed. Secondly, the confinement enhancement factors are calculated to evaluate the performance of KSTAR H-modes. The calculated H{sub 89-p} and H{sub 98} (y, 2) represent that the confinement is enhanced in most KSTAR H-mode discharges. Interestingly, even in L-mode phases, confinement is observed to be enhanced against the multi-machine scalings. H{sub exp} factor is newly introduced to evaluate the amount of confinement improvement in the H-mode phase compared with the L-mode phase in a single discharge. H{sub exp} exhibits that the global energy confinement time of the H-mode phase is improved about 1.3 - 2.0 times compared with that of the L-mode phase. Finally, interpretive and predictive numerical simulations are carried out using the ASTRA code for typical KSTAR H-mode discharges. The Weiland model and the GLF23 model are employed for calculating the anomalous contributions of both electron and ion heat transport in predictive simulations. For the H-mode phase, the Weiland model reproduces the experiment

Transition from L mode to high ion temperature mode in CHS heliotron/torsatron plasmas

International Nuclear Information System (INIS)

Ida, K.; Osakabe, M.; Tanaka, K.

2001-01-01

A high ion temperature mode (high T i mode) is observed for neutral beam heated plasmas in the Compact Helical System (CHS) Heliotron/torsatron. The high T i mode plasma is characterized by a high central ion temperature, T i (0), and is associated with a peaked electron density profile produced by neutral beam fueling with low wall recycling. Transition from L mode to high T i mode has been studied in CHS. The central ion temperature in the high T i mode discharges reaches to 1 keV which is 2.5 times higher than that in the L mode discharges. The ion thermal diffusivity is significantly reduced by a factor of more than 2-3 in the high T i mode plasma. The ion loss cone is observed in neutral particle flux in the energy range of 1-6 keV with a narrow range of pitch angle (90±10 degree) in the high T i mode. However, the degradation of ion energy confinement due to this loss cone is negligible. (author)

Mode conversion efficiency to Laguerre-Gaussian OAM modes using spiral phase optics.

Science.gov (United States)

Longman, Andrew; Fedosejevs, Robert

2017-07-24

An analytical model for the conversion efficiency from a TEM 00 mode to an arbitrary Laguerre-Gaussian (LG) mode with null radial index spiral phase optics is presented. We extend this model to include the effects of stepped spiral phase optics, spiral phase optics of non-integer topological charge, and the reduction in conversion efficiency due to broad laser bandwidth. We find that through optimization, an optimal beam waist ratio of the input and output modes exists and is dependent upon the output azimuthal mode number.

Perspective gyrotron with mode converter for co- and counter-rotation operating modes

Energy Technology Data Exchange (ETDEWEB)

Chirkov, A. V.; Kuftin, A. N. [Institute of Applied Physics, Russian Academy of Sciences, 46 Ul' yanov Street, 603950 Nizhny Novgorod (Russian Federation); Denisov, G. G. [Institute of Applied Physics, Russian Academy of Sciences, 46 Ul' yanov Street, 603950 Nizhny Novgorod (Russian Federation); University of Nizhny Novgorod, 23 Prospekt Gagarina, 603950 Nizhny Novgorod (Russian Federation)

2015-06-29

A gyrotron oscillator operating efficiently at modes of both rotations was developed and tested. The gyrotron operation can be switched between two modes: co- and counter rotating ones with respect to electron rotation in a resonance magnetic field. A synthesized mode converter provides output of both waves in the form of two different paraxial wave beams corresponding to direction of the mode rotation. Measured gyrotron power (up to 2 MW), interaction efficiency (34%), and diffraction losses in the mode converter (≈2%) agree well with the design values. The proposed gyrotron scheme alloys principal enhancement in the device parameters—possibility of electronic switching of output wave beam direction and possibility to arrange an effective scheme to provide frequency/phase locking of a gyrotron-oscillator.

Perspective gyrotron with mode converter for co- and counter-rotation operating modes

International Nuclear Information System (INIS)

Chirkov, A. V.; Kuftin, A. N.; Denisov, G. G.

2015-01-01

A gyrotron oscillator operating efficiently at modes of both rotations was developed and tested. The gyrotron operation can be switched between two modes: co- and counter rotating ones with respect to electron rotation in a resonance magnetic field. A synthesized mode converter provides output of both waves in the form of two different paraxial wave beams corresponding to direction of the mode rotation. Measured gyrotron power (up to 2 MW), interaction efficiency (34%), and diffraction losses in the mode converter (≈2%) agree well with the design values. The proposed gyrotron scheme alloys principal enhancement in the device parameters—possibility of electronic switching of output wave beam direction and possibility to arrange an effective scheme to provide frequency/phase locking of a gyrotron-oscillator

Robust fiber optic flexure sensor exploiting mode coupling in few-mode fiber

Science.gov (United States)

Nelsen, Bryan; Rudek, Florian; Taudt, Christopher; Baselt, Tobias; Hartmann, Peter

2015-05-01

Few-mode fiber (FMF) has become very popular for use in multiplexing telecommunications data over fiber optics. The simplicity of producing FMF and the relative robustness of the optical modes, coupled with the simplicity of reading out the information make this fiber a natural choice for communications. However, little work has been done to take advantage of this type of fiber for sensors. Here, we demonstrate the feasibility of using FMF properties as a mechanism for detecting flexure by exploiting mode coupling between modes when the cylindrical symmetry of the fiber is perturbed. The theoretical calculations shown here are used to understand the coupling between the lowest order linearly polarized mode (LP01) and the next higher mode (LP11x or LP11y) under the action of bending. Twisting is also evaluated as a means to detect flexure and was determined to be the most reliable and effective method when observing the LP21 mode. Experimental results of twisted fiber and observations of the LP21 mode are presented here. These types of fiber flexure sensors are practical in high voltage, high magnetic field, or high temperature medical or industrial environments where typical electronic flexure sensors would normally fail. Other types of flexure measurement systems that utilize fiber, such as Rayleigh back-scattering [1], are complicated and expensive and often provide a higher-than necessary sensitivity for the task at hand.

Comparison of detectability in step-and-shoot mode and continuous mode digital tomosynthesis systems

Science.gov (United States)

Lee, Changwoo; Han, Minah; Baek, Jongduk

2017-03-01

Digital tomosynthesis system has been widely used in chest, dental, and breast imaging. Since the digital tomosynthesis system provides volumetric images from multiple projection data, structural noise inherent in X-ray radiograph can be reduced, and thus signal detection performance is improved. Currently, tomosynthesis system uses two data acquisition modes: step-and-shoot mode and continuous mode. Several studies have been conducted to compare the system performance of two acquisition modes with respect to spatial resolution and contrast. In this work, we focus on signal detectability in step-and-shoot mode and continuous mode. For evaluation, uniform background is considered, and eight spherical objects with diameters of 0.5, 0.8, 1, 2, 3, 5, 8, 10 mm are used as signals. Projection data with and without spherical objects are acquired in step-and-shoot mode and continuous mode, respectively, and quantum noise are added. Then, noisy projection data are reconstructed by FDK algorithm. To compare the detection performance of two acquisition modes, we calculate task signal-to-noise ratio (SNR) of channelized Hotelling observer with Laguerre-Gauss channels for each spherical object. While the task-SNR values of two acquisition modes are similar for spherical objects larger than 1 mm diameter, step-and-shoot mode yields higher detectability for small signal sizes. The main reason of this behavior is that small signal is more affected by X-ray tube motion blur than large signal. Our results indicate that it is beneficial to use step-and-shoot data acquisition mode to improve the detectability of small signals (i.e., less than 1 mm diameter) in digital tomosynthesis systems.

Normal modes of Bardeen discs

International Nuclear Information System (INIS)

Verdaguer, E.

1983-01-01

The short wavelength normal modes of self-gravitating rotating polytropic discs in the Bardeen approximation are studied. The discs' oscillations can be seen in terms of two types of modes: the p-modes whose driving forces are pressure forces and the r-modes driven by Coriolis forces. As a consequence of differential rotation coupling between the two takes place and some mixed modes appear, their properties can be studied under the assumption of weak coupling and it is seen that they avoid the crossing of the p- and r-modes. The short wavelength analysis provides a basis for the classification of the modes, which can be made by using the properties of their phase diagrams. The classification is applied to the large wavelength modes of differentially rotating discs with strong coupling and to a uniformly rotating sequence with no coupling, which have been calculated in previous papers. Many of the physical properties and qualitative features of these modes are revealed by the analysis. (author)

Tacoma mode

International Nuclear Information System (INIS)

Courant, E.D.; Ruth, R.D.; Wang, J.M.

1979-01-01

The name Tacoma refers to the Tacoma Narrows Bridge which collapsed on November 8, 1940 due to massive oscillations caused by high winds. One of the destructive modes was a torsion mode which was excited by transverse wind, a dipole force, and continued until the bridge collapsed. The name is used to refer to a coherent mode of oscillation of a spectrum of oscillators in which the amplitude vs frequency graph contains one node, where the node occurs near the driving frequency and a ω is not symmetric about zero. When this result is applied to vertical instabilities in coasting beams, it implies the existence of a coherent skew quadrupole moment, Q/sub xy/, whenever a coherent dipole oscillation exists

Pad-mode-induced instantaneous mode instability for simple models of brake systems

Science.gov (United States)

Oberst, S.; Lai, J. C. S.

2015-10-01

Automotive disc brake squeal is fugitive, transient and remains difficult to predict. In particular, instantaneous mode squeal observed experimentally does not seem to be associated with mode coupling and its mechanism is not clear. The effects of contact pressures, friction coefficients as well as material properties (pressure and temperature dependency and anisotropy) for brake squeal propensity have not been systematically explored. By analysing a finite element model of an isotropic pad sliding on a plate similar to that of a previously reported experimental study, pad modes have been identified and found to be stable using conventional complex eigenvalue analysis. However, by subjecting the model to contact pressure harmonic excitation for a range of pressures and friction coefficients, a forced response analysis reveals that the dissipated energy for pad modes is negative and becomes more negative with increasing contact pressures and friction coefficients, indicating the potential for instabilities. The frequency of the pad mode in the sliding direction is within the range of squeal frequencies observed experimentally. Nonlinear time series analysis of the vibration velocity also confirms the evolution of instabilities induced by pad modes as the friction coefficient increases. By extending this analysis to a more realistic but simple brake model in the form of a pad-on-disc system, in-plane pad-modes, which a complex eigenvalue analysis predicts to be stable, have also been identified by negative dissipated energy for both isotropic and anisotropic pad material properties. The influence of contact pressures on potential instabilities has been found to be more dominant than changes in material properties owing to changes in pressure or temperature. Results here suggest that instantaneous mode squeal is likely caused by in-plane pad-mode instabilities.

The Integrated Mode Management Interface

Science.gov (United States)

Hutchins, Edwin

1996-01-01

Mode management is the processes of understanding the character and consequences of autoflight modes, planning and selecting the engagement, disengagement and transitions between modes, and anticipating automatic mode transitions made by the autoflight system itself. The state of the art is represented by the latest designs produced by each of the major airframe manufacturers, the Boeing 747-400, the Boeing 777, the McDonnell Douglas MD-11, and the Airbus A320/A340 family of airplanes. In these airplanes autoflight modes are selected by manipulating switches on the control panel. The state of the autoflight system is displayed on the flight mode annunciators. The integrated mode management interface (IMMI) is a graphical interface to autoflight mode management systems for aircraft equipped with flight management computer systems (FMCS). The interface consists of a vertical mode manager and a lateral mode manager. Autoflight modes are depicted by icons on a graphical display. Mode selection is accomplished by touching (or mousing) the appropriate icon. The IMMI provides flight crews with an integrated interface to autoflight systems for aircraft equipped with flight management computer systems (FMCS). The current version is modeled on the Boeing glass-cockpit airplanes (747-400, 757/767). It runs on the SGI Indigo workstation. A working prototype of this graphics-based crew interface to the autoflight mode management tasks of glass cockpit airplanes has been installed in the Advanced Concepts Flight Simulator of the CSSRF of NASA Ames Research Center. This IMMI replaces the devices in FMCS equipped airplanes currently known as mode control panel (Boeing), flight guidance control panel (McDonnell Douglas), and flight control unit (Airbus). It also augments the functions of the flight mode annunciators. All glass cockpit airplanes are sufficiently similar that the IMMI could be tailored to the mode management system of any modern cockpit. The IMMI does not replace the

Poloidal rotation and the evolution of H-mode and VH-mode profiles

International Nuclear Information System (INIS)

Hinton, F.L.; Staebler, G.M.; Kim, Y.B.

1993-12-01

The physics which determines poloidal rotation, and its role in the development of profiles during H- and VH-modes, is discussed. A simple phenomenological transport model, which incorporates the rvec E x rvec B flow shear suppression of turbulence, is shown to predict profile evolution similar to that observed experimentally during H-mode and VH-mode

Optical Comb from a Whispering Gallery Mode Resonator for Spectroscopy and Astronomy Instruments Calibration

Science.gov (United States)

Strekalov, Dmitry V.; Yu, Nam; Thompson, Robert J.

2012-01-01

The most accurate astronomical data is available from space-based observations that are not impeded by the Earth's atmosphere. Such measurements may require spectral samples taken as long as decades apart, with the 1 cm/s velocity precision integrated over a broad wavelength range. This raises the requirements specifically for instruments used in astrophysics research missions -- their stringent wavelength resolution and accuracy must be maintained over years and possibly decades. Therefore, a stable and broadband optical calibration technique compatible with spaceflights becomes essential. The space-based spectroscopic instruments need to be calibrated in situ, which puts forth specific requirements to the calibration sources, mainly concerned with their mass, power consumption, and reliability. A high-precision, high-resolution reference wavelength comb source for astronomical and astrophysics spectroscopic observations has been developed that is deployable in space. The optical comb will be used for wavelength calibrations of spectrographs and will enable Doppler measurements to better than 10 cm/s precision, one hundred times better than the current state-of-the- art.

Design considerations in achieving 1 MW CW operation with a whispering-gallery-mode gyrotron

International Nuclear Information System (INIS)

Felch, K.; Feinstein, J.; Hess, C.; Huey, H.; Jongewaard, E.; Jory, H.; Neilson, J.; Pendleton, R.; Pirkle, D.; Zitelli, L.

1989-09-01

Varian is developing high-power, CW gyrotrons at frequencies in the range 100 GHz to 150 GHz, for use in electron cyclotron heating applications. Early test vehicles have utilized a TE 15,2,1 interaction cavity, have achieved short-pulse power levels of 820 kW and average power levels of 80 kW at 140 GHz. Present tests are aimed at reaching 400 kW under CW operating conditions and up to 1 MW for short pulse durations. Work is also underway on modifications to the present design that will enable power levels of up to 1 MW CW to be achieved. 7 refs., 2 figs

Design and numerical optimization of a mode multiplexer based on few-mode fiber couplers

International Nuclear Information System (INIS)

Xie, Yiwei; Fu, Songnian; Liu, Hai; Zhang, Hailiang; Tang, Ming; Liu, Deming; Shum, P

2013-01-01

Mode division multiplexing (MDM) transmission based on few-mode fibers (FMFs) appears to be an alternative solution for overcoming the capacity limit of single-mode fibers (SMFs). A FMF coupler-based mode division multiplexer/demultiplexer (MMUX/DeMMUX) is proposed and theoretically investigated after the fabricated FMF is characterized. MMUXs/DeMMUXs with a mode contrast ratio (MCR) of more than 20 dB can be obtained for two-mode multiplexing and three-mode multiplexing over a wavelength span of 60 and 10 nm, respectively. We numerically verify the proposed MMUX/DeMMUX which has the advantages of high MCR, easy fabrication and maintenance, and low wavelength dependence. (paper)

Mode coupling trigger of neoclassical magnetohydrodynamic tearing modes in tokamaks

International Nuclear Information System (INIS)

Gianakon, T.A.; Hegna, C.C.; Callen, J.D.

1997-05-01

Numerical studies of the nonlinear evolution of coupled magnetohydrodynamic - type tearing modes in three-dimensional toroidal geometry with neoclassical effects are presented. The inclusion of neoclassical physics introduces an additional free-energy source for the nonlinear formation of magnetic islands through the effects of a bootstrap current in Ohm's law. The neoclassical tearing mode is demonstrated to be destabilized in plasmas which are otherwise Δ' stable, albeit once a threshold island width is exceeded. A possible mechanism for exceeding or eliminating this threshold condition is demonstrated based on mode coupling due to toroidicity with a pre-existing instability at the q = 1 surface

Synergetic scattering of SiO2 and Ag nanoparticles for light-trapping enhancement in organic bulk heterojunction

Science.gov (United States)

Yang, Huan; Ding, Qiuyu; Li, Ben Q.; Jiang, Xinbing; Zhang, Manman

2018-02-01

Though noble metal nanoparticles have been explored to enhance the performance of the organic solar cell, effect of dielectric nanoparticles, and coupled effect of dielectric and metal nanoparticles, have rarely been reported, if at all, on organic solar cell. This work reports an experimental study on synergetic scattering of SiO2 and Ag nanoparticles in a bulk organic heterojunction for the broadband light absorption enhancement. The wavelength scale SiO2 particles were arranged as a monolayer on the surface of the solar cell to guide incident light into the active layer and prolong the effective optical length of the entered energy. This is achieved by the excitation of whispering gallery modes in SiO2 nanoparticles and by leaky mode radiation. When small size Ag particles were incorporated into the transport layer of the solar cell, synergetic scattering of SiO2 and Ag nanoparticles is formed by coupling of the whispering gallery mode of closely arranged SiO2 particles atop and collaborative localized surface plasma resonance scattering of Ag nanoparticles dispersed in the transport layer. As a result, the performance of the organic solar cell is greatly enhanced and the short-circuit current density has an improvement of 42.47%. Therefore, the organic solar cell incorporated with SiO2 and Ag particles presents a meaningful strategy to achieve high energy-harvesting performance. [Figure not available: see fulltext.

Self-rated health assessed by web versus mail modes in a mixed mode survey: the digital divide effect and the genuine survey mode effect.

Science.gov (United States)

Shim, Jae-Mahn; Shin, Eunjung; Johnson, Timothy P

2013-09-01

To investigate differences in self-rated health (SRH) between web and mail questionnaires in a mixed mode survey and to provide a model that explains those differences. A total of 15,200 mail respondents and 17,829 web respondents from the 2008 US National Health Survey conducted by the Gallup Panel. Respondents were recruited using random digit dialing and assigned to one of the two survey modes (web or mail). Respondents with household Internet connection and frequent Internet usage were invited to complete the survey through the web mode. Respondents who had no Internet connection or who used the Internet infrequently were invited to the mail mode. Thus, respondents with better Internet access used the web mode. Respondents completed a questionnaire that asked about SRH status, objective health conditions, health behaviors, and other socioeconomic variables. Statistical associations were analyzed with ordered Logit and negative binomial models. Web respondents reported better SRH than mail respondents. This difference is in part reflective of variability in objective health status between these two groups, and in part attributable to the effects of survey mode. These results maintained with age controlled. The alignment between survey mode selection, Internet access, and health disparities, as well as genuine survey mode characteristics, leads to web-mail differences in SRH. Unless the digital divide and its influences on survey mode selection are resolved and differential genuine mode effects are fully comprehended, we recommend that both modes be simultaneously used on a complementary basis.

Characteristics of edge localized mode in JFT-2M H-mode

International Nuclear Information System (INIS)

Matsumoto, Hiroshi; Funahashi, Akimasa; Goldston, R.J.

1989-03-01

Characteristics of edge localized mode (ELM/ERP) during H-mode plasma of JFT-2M were investigated. It was found that ELM/ERP is mainly a density fluctuation phenomena in the edge, and electron temperature in the edge except just near the separatrix is not very much perturbed. Several experimental conditions to controll ELM/ERP are, plasma density, plasma ion species, heating power, and plasma current ramping. ELM/ERPs found in low density deuterium discharge are suppressed by raising the density. ELM/ERPs are pronounced in hydrogen plasma compared with deuterium plasma. ELM/ERPs seen in hydrogen plasma or in near marginal H-mode conditions are suppressed by increasing the heating power. ELM/ERPs are found to be suppressed by plasma current ramp down, whereas they are enhanced by current ramp up. MHD aspect of ELM/ERP was investigated. No clear MHD features of ELM/ERP were found. However, reversal of mode rotation seen imediately after ELM/ERP suggests the temporal return to L-mode during the ELM/ERP event. (author)

All-fiber optical mode switching based on cascaded mode selective couplers for short-reach MDM networks

Science.gov (United States)

Ren, Fang; Li, Juhao; Wu, Zhongying; Yu, Jinyi; Mo, Qi; Wang, Jianping; He, Yongqi; Chen, Zhangyuan; Li, Zhengbin

2017-04-01

We propose and experimentally demonstrate an all-fiber optical mode switching structure supporting independent switching, exchanging, adding, and dropping functionalities in which each mode can be switched individually. The mode switching structure consists of cascaded mode selective couplers (MSCs) capable of exciting and selecting specific higher order modes in few-mode fibers with high efficiency and one multiport optical switch routing the independent spatial modes to their destinations. The data carried on three different spatial modes can be switched, exchanged, added, and dropped through this all-fiber structure. For this experimental demonstration, optical on-off-keying (OOK) signals at 10-Gb/s carried on three spatial modes are successfully processed with open and clear eye diagrams. The mode switch exhibits power penalties of less than 3.1 dB after through operation, less than 2.7 dB after exchange operation, less than 2.8 dB after switching operation, and less than 1.6 dB after mode adding and dropping operations at the bit-error rate (BER) of 10-3, while all three channels carried on three spatial modes are simultaneously routed. The proposed structure, compatible with current optical switching networks based on single-mode fibers, can potentially be used to expand the switching scalability in advanced and flexible short-reach mode-division multiplexing-based networks.

Single-mode regime in large-mode-area rare-earth-doped rod-type PCFs

DEFF Research Database (Denmark)

Poli, F.; Cucinotta, A.; Passaro, D.

2009-01-01

In this paper, large-mode-area, double-cladding, rare-earth-doped photonic crystal fibers are investigated in order to understand how the refractive index distribution and the mode competition given by the amplification can assure single-mode propagation. Fibers with different core diameters, i...

Cross-correlated imaging of single-mode photonic crystal rod fiber with distributed mode filtering

DEFF Research Database (Denmark)

Laurila, Marko; Barankov, Roman; Jørgensen, Mette Marie

2013-01-01

Photonic crystal bandgap fibers employing distributed mode filtering design provide near diffraction-limited light outputs, a critical property of fiber-based high-power lasers. Microstructure of the fibers is tailored to achieve single-mode operation at specific wavelength by resonant mode...... identify regimes of resonant coupling between higher-order core modes and cladding band. We demonstrate a passive fiber design in which the higher-order modal content inside the single-mode guiding regime is suppressed by at least 20 dB even for significantly misaligned input-coupling configurations....

Cavity optomechanics in a levitated helium drop

Science.gov (United States)

Childress, L.; Schmidt, M. P.; Kashkanova, A. D.; Brown, C. D.; Harris, G. I.; Aiello, A.; Marquardt, F.; Harris, J. G. E.

2017-12-01

We describe a proposal for a type of optomechanical system based on a drop of liquid helium that is magnetically levitated in vacuum. In the proposed device, the drop would serve three roles: its optical whispering-gallery modes would provide the optical cavity, its surface vibrations would constitute the mechanical element, and evaporation of He atoms from its surface would provide continuous refrigeration. We analyze the feasibility of such a system in light of previous experimental demonstrations of its essential components: magnetic levitation of mm-scale and cm-scale drops of liquid He , evaporative cooling of He droplets in vacuum, and coupling to high-quality optical whispering-gallery modes in a wide range of liquids. We find that the combination of these features could result in a device that approaches the single-photon strong-coupling regime, due to the high optical quality factors attainable at low temperatures. Moreover, the system offers a unique opportunity to use optical techniques to study the motion of a superfluid that is freely levitating in vacuum (in the case of 4He). Alternatively, for a normal fluid drop of 3He, we propose to exploit the coupling between the drop's rotations and vibrations to perform quantum nondemolition measurements of angular momentum.

Failure mode and effects analysis: an empirical comparison of failure mode scoring procedures.

Science.gov (United States)

Ashley, Laura; Armitage, Gerry

2010-12-01

To empirically compare 2 different commonly used failure mode and effects analysis (FMEA) scoring procedures with respect to their resultant failure mode scores and prioritization: a mathematical procedure, where scores are assigned independently by FMEA team members and averaged, and a consensus procedure, where scores are agreed on by the FMEA team via discussion. A multidisciplinary team undertook a Healthcare FMEA of chemotherapy administration. This included mapping the chemotherapy process, identifying and scoring failure modes (potential errors) for each process step, and generating remedial strategies to counteract them. Failure modes were scored using both an independent mathematical procedure and a team consensus procedure. Almost three-fifths of the 30 failure modes generated were scored differently by the 2 procedures, and for just more than one-third of cases, the score discrepancy was substantial. Using the Healthcare FMEA prioritization cutoff score, almost twice as many failure modes were prioritized by the consensus procedure than by the mathematical procedure. This is the first study to empirically demonstrate that different FMEA scoring procedures can score and prioritize failure modes differently. It found considerable variability in individual team members' opinions on scores, which highlights the subjective and qualitative nature of failure mode scoring. A consensus scoring procedure may be most appropriate for FMEA as it allows variability in individuals' scores and rationales to become apparent and to be discussed and resolved by the team. It may also yield team learning and communication benefits unlikely to result from a mathematical procedure.

Surface tearing modes in tokamaks

International Nuclear Information System (INIS)

Takizuka, Tomonori; Kurita, Gen-ichi; Azumi, Masafumi; Takeda, Tatsuoki

1985-10-01

Surface tearing modes in tokamaks are studied numerically and analytically. The eigenvalue problem is solved to obtain the growth rate and the mode structure. We investigate in detail dependences of the growth rate of the m/n = 2/1 resistive MHD modes on the safety factor at the plasma surface, current profile, wall position, and resistivity. The surface tearing mode moves the plasma surface even when the wall is close to the surface. The stability diagram for these modes is presented. (author)

Resonator modes and mode dynamics for an external cavity-coupled laser array

Science.gov (United States)

Nair, Niketh; Bochove, Erik J.; Aceves, Alejandro B.; Zunoubi, Mohammad R.; Braiman, Yehuda

2015-03-01

Employing a Fox-Li approach, we derived the cold-cavity mode structure and a coupled mode theory for a phased array of N single-transverse-mode active waveguides with feedback from an external cavity. We applied the analysis to a system with arbitrary laser lengths, external cavity design and coupling strengths to the external cavity. The entire system was treated as a single resonator. The effect of the external cavity was modeled by a set of boundary conditions expressed by an N-by-N frequency-dependent matrix relation between incident and reflected fields at the interface with the external cavity. The coupled mode theory can be adapted to various types of gain media and internal and external cavity designs.

Excursions through KK modes

Energy Technology Data Exchange (ETDEWEB)

Furuuchi, Kazuyuki [Manipal Centre for Natural Sciences, Manipal University,Manipal, Karnataka 576104 (India)

2016-07-07

In this article we study Kaluza-Klein (KK) dimensional reduction of massive Abelian gauge theories with charged matter fields on a circle. Since local gauge transformations change position dependence of the charged fields, the decomposition of the charged matter fields into KK modes is gauge dependent. While whole KK mass spectrum is independent of the gauge choice, the mode number depends on the gauge. The masses of the KK modes also depend on the field value of the zero-mode of the extra dimensional component of the gauge field. In particular, one of the KK modes in the KK tower of each massless 5D charged field becomes massless at particular values of the extra-dimensional component of the gauge field. When the extra-dimensional component of the gauge field is identified with the inflaton, this structure leads to recursive cosmological particle productions.

Excursions through KK modes

International Nuclear Information System (INIS)

Furuuchi, Kazuyuki

2016-01-01

In this article we study Kaluza-Klein (KK) dimensional reduction of massive Abelian gauge theories with charged matter fields on a circle. Since local gauge transformations change position dependence of the charged fields, the decomposition of the charged matter fields into KK modes is gauge dependent. While whole KK mass spectrum is independent of the gauge choice, the mode number depends on the gauge. The masses of the KK modes also depend on the field value of the zero-mode of the extra dimensional component of the gauge field. In particular, one of the KK modes in the KK tower of each massless 5D charged field becomes massless at particular values of the extra-dimensional component of the gauge field. When the extra-dimensional component of the gauge field is identified with the inflaton, this structure leads to recursive cosmological particle productions.

Neoclassical tearing mode seeding by coupling with infernal modes in low-shear tokamaks

Science.gov (United States)

Kleiner, A.; Graves, J. P.; Brunetti, D.; Cooper, W. A.; Halpern, F. D.; Luciani, J.-F.; Lütjens, H.

2016-09-01

A numerical and an analytical study of the triggering of resistive MHD modes in tokamak plasmas with low magnetic shear core is presented. Flat q profiles give rise to fast growing pressure driven MHD modes, such as infernal modes. It has been shown that infernal modes drive fast growing islands on neighbouring rational surfaces. Numerical simulations of such instabilities in a MAST-like configuration are performed with the initial value stability code XTOR-2F in the resistive frame. The evolution of magnetic islands are computed from XTOR-2F simulations and an analytical model is developed based on Rutherford’s theory in combination with a model of resistive infernal modes. The parameter {{Δ }\\prime} is extended from the linear phase to the non-linear phase. Additionally, the destabilising contribution due to a helically perturbed bootstrap current is considered. Comparing the numerical XTOR-2F simulations to the model, we find that coupling has a strong destabilising effect on (neoclassical) tearing modes and is able to seed 2/1 magnetic islands in situations when the standard NTM theory predicts stability.

Enhancement of mode-converted electron Bernstein wave emission during National Spherical Torus Experiment H-mode plasmas

International Nuclear Information System (INIS)

Taylor, G.; Efthimion, P.C.; Jones, B.; Le Blanc, B.P.; Maingi, R.

2002-01-01

A sudden, threefold increase in emission from fundamental electrostatic electron Bernstein waves (EBW) which mode convert and tunnel to the electromagnetic X-mode has been observed during high energy and particle confinement (H-mode) transitions in the National Spherical Torus Experiment (NSTX) plasma [M. Ono, S. Kaye, M. Peng et al., in Proceedings of the 17th IAEA Fusion Energy Conference (IAEA, Vienna, Austria, 1999), Vol. 3, p. 1135]. The mode-converted EBW emission viewed normal to the magnetic field on the plasma midplane increases when the density profile steepens in the vicinity of the mode conversion layer, which is located in the plasma scrape off. The measured conversion efficiency during the H-mode is consistent with the calculated EBW to X-mode conversion efficiency derived using edge density data. Calculations indicate that there may also be a small residual contribution to the measured X-mode electromagnetic radiation from polarization-scrambled, O-mode emission, converted from EBWs

Role of Edge Inclination in an Optical Microdisk Resonator for Label-Free Sensing

OpenAIRE

Gandolfi, Davide; Ramiro-Manzano, Fernando; Rebollo, Francisco Javier Aparicio; Ghulinyan, Mher; Pucker, Georg; Pavesi, Lorenzo

2015-01-01

In this paper, we report on the measurement and modeling of enhanced optical refractometric sensors based on whispering gallery modes. The devices under test are optical microresonators made of silicon nitride on silicon oxide, which differ in their sidewall inclination angle. In our approach, these microresonators are vertically coupled to a buried waveguide with the aim of creating integrated and cost-effective devices. Device modeling shows that the optimization of the devic...

Mode-synthesizing atomic force microscopy and mode-synthesizing sensing

Science.gov (United States)

Passain, Ali; Thundat, Thomas George; Tetard, Laurene

2014-07-22

A method of analyzing a sample that includes applying a first set of energies at a first set of frequencies to a sample and applying, simultaneously with the applying the first set of energies, a second set of energies at a second set of frequencies, wherein the first set of energies and the second set of energies form a multi-mode coupling. The method further includes detecting an effect of the multi-mode coupling.

Mode synthesizing atomic force microscopy and mode-synthesizing sensing

Science.gov (United States)

Passian, Ali; Thundat, Thomas George; Tetard, Laurene

2013-05-17

A method of analyzing a sample that includes applying a first set of energies at a first set of frequencies to a sample and applying, simultaneously with the applying the first set of energies, a second set of energies at a second set of frequencies, wherein the first set of energies and the second set of energies form a multi-mode coupling. The method further includes detecting an effect of the multi-mode coupling.

Mixed-mode fracture of ceramics

Energy Technology Data Exchange (ETDEWEB)

Petrovic, J.J.

1985-01-01

The mixed-mode fracture behavior of ceramic materials is of importance for monolithic ceramics in order to predict the onset of fracture under generalized loading conditions and for ceramic composites to describe crack deflection toughening mechanisms. Experimental data on surface flaw mixed-mode fracture in various ceramics indicate that the flaw-plane normal stress at fracture decreases with increasing in-flaw-plane shear stress, although present data exhibit a fairly wide range in details of this sigma - tau relationship. Fracture from large cracks suggests that Mode II has a greater effect on Mode I fracture than Mode III. A comparison of surface flaw and large crack mixed-mode I-II fracture responses indicated that surface flaw behavior is influenced by shear resistance effects.

Paper-based biodetection using luminescent nanoparticles.

Science.gov (United States)

Ju, Qiang; Noor, M Omair; Krull, Ulrich J

2016-05-10

Point-of-care and in-field technologies for rapid, sensitive and selective detection of molecular biomarkers have attracted much interest. Rugged bioassay technology capable of fast detection of markers for pathogens and genetic diseases would in particular impact the quality of health care in the developing world, but would also make possible more extensive screening in developed countries to tackle problems such as those associated with water and food quality, and tracking of infectious organisms in hospitals and clinics. Literature trends indicate an increasing interest in the use of nanomaterials, and in particular luminescent nanoparticles, for assay development. These materials may offer attributes for development of assays and sensors that could achieve improvements in analytical figures of merit, and provide practical advantages in sensitivity and stability. There is opportunity for cost-efficiency and technical simplicity by implementation of luminescent nanomaterials as the basis for transduction technology, when combined with the use of paper substrates, and the ubiquitous availability of cell phone cameras and associated infrastructure for optical detection and transmission of results. Luminescent nanoparticles have been described for a broad range of bioanalytical targets including small molecules, oligonucleotides, peptides, proteins, saccharides and whole cells (e.g., cancer diagnostics). The luminescent nanomaterials that are described herein for paper-based bioassays include metal nanoparticles, quantum dots and lanthanide-doped nanocrystals. These nanomaterials often have broad and strong absorption and narrow emission bands that improve opportunity for multiplexed analysis, and can be designed to provide emission at wavelengths that are efficiently processed by conventional digital cameras. Luminescent nanoparticles can be embedded in paper substrates that are designed to direct fluid flow, and the resulting combination of technologies can offer competitive analytical performance at relatively low cost.

Planar Hall Effect Sensors for Biodetection

DEFF Research Database (Denmark)

Rizzi, Giovanni

. In the second geometry (dPHEB) half of the sensor is used as a local negative reference to subtract the background signal from magnetic beads in suspension. In all applications below, the magnetic beads are magnetised using the magnetic field due to the bias current passed through the sensor, i.e., no external...... as labels and planar Hall effect bridge (PHEB) magnetic field sensor as readout for the beads. The choice of magnetic beads as label is motivated by the lack of virtually any magnetic background from biological samples. Moreover, magnetic beads can be manipulated via an external magnetic field...... hybridisation in real-time, in a background of suspended magnetic beads. This characteristic is employed in single nucleotide polymorphism (SNP) genotyping, where the denaturation of DNA is monitored in real-time upon washing with a stringency buffer. The sensor setup includes temperature control and a fluidic...

Single-mode ytterbium-doped large-mode-area photonic bandgap rod fiber amplifier

DEFF Research Database (Denmark)

Alkeskjold, Thomas Tanggaard; Scolari, Lara; Broeng, Jes

2011-01-01

bandgap structure. The structure allows resonant coupling of higher-order modes from the core and acts as a spatially Distributed Mode Filter (DMF). With this approach, we demonstrate passive SM performance in an only ~50cm long and straight ytterbium-doped rod fiber. The amplifier has a mode field...... diameter of ∼59Lim at 1064nm and exhibits a pump absorption of 27dB/m at 976nm. © 2011 Optical Society of America....

Interferometric characterization of few-mode fibers (FMF) for mode-division multiplexing (MDM)

OpenAIRE

Muliar, Olena; Usuga Castaneda, Mario A.; Rottwitt, Karsten; Lægsgaard, Jesper

2015-01-01

The rapid growth of global data traffic demands the continuous search for new technologies and systems that could increase transmission capacity in optical links and recent experiments show that to do so, it is advantageous to explore new degrees of freedom such as polarization, wavelength or optical modes. Mode division multiplexing (MDM) appears in this context as a promising and viable solution for such capacity increase, since it utilizes multiple spatial modes of an optical fiber as indi...

Nonlinear drift tearing mode

International Nuclear Information System (INIS)

Zelenyj, L.M.; Kuznetsova, M.M.

1989-01-01

Nonlinear study of magnetic perturbation development under single-mode conditions in collision-free plasma in configurations with the magnetic field shear is investigated. Results are obtained with regard of transverse component of electrical field and its effect on ion dynamics within wide range of ion Larmor radius value and values of magnetic field shear. Increments of nonlinear drift tearing mode are obtained and it is shown that excitation drastic conditions of even linearly stable modes are possible. Mechanism of instability nonlinear stabilization is considered and the value of magnetic island at the saturation threshold is estimeted. Energy of nonlinear drift tearing mode is discussed

Constructing petal modes from the coherent superposition of Laguerre-Gaussian modes

Science.gov (United States)

Naidoo, Darryl; Forbes, Andrew; Ait-Ameur, Kamel; Brunel, Marc

2011-03-01

An experimental approach in generating Petal-like transverse modes, which are similar to what is seen in porro-prism resonators, has been successfully demonstrated. We hypothesize that the petal-like structures are generated from a coherent superposition of Laguerre-Gaussian modes of zero radial order and opposite azimuthal order. To verify this hypothesis, visually based comparisons such as petal peak to peak diameter and the angle between adjacent petals are drawn between experimental data and simulated data. The beam quality factor of the Petal-like transverse modes and an inner product interaction is also experimentally compared to numerical results.

X-ray fractography of fatigue fracture surface under mode I and mode III loading

International Nuclear Information System (INIS)

Akiniwa, Yoshiaki; Tanaka, Keisuke; Tsumura, Tsuyoshi

2001-01-01

The propagation behavior of a circumferential fatigue crack in cylindrical bars of a carbon steel (JIS SGV410) and a stainless steel (JIS SUS316NG) was investigated under cyclic axial and torsional loadings. The J-integral range was used as a fracture mechanics parameter. When compared at the same J-integral range, the crack propagation rate under mode III was smaller than that under mode I. Parallel markings perpendicular to the crack propagation direction were observed on the fatigue fracture surface obtained under mode III loading. The residual stresses in the radial direction, σ r , and in the tangential direction, σ θ , were measured for both mode I and mode III fatigue fracture surfaces. For mode I fracture surface, σ r was tension, and was almost constant irrespective of the applied J-integral range. σ θ was close to zero for both materials. On the other hand, for mode III, σ r and σ θ were compression. For SUS316NG steel, the compressive stress of σ θ increased with the J-integral range. For SGV410 steel, the change of σ θ with the J-integral range was small. The breadth of diffraction profiles increased with J-integral range for both mode I and III. The breadth was found to be a good parameter to evaluate the applied J-integral range. (author)

Comprehensive comparison of macro-strain mode and displacement mode based on different sensing technologies

Science.gov (United States)

Hong, Wan; Zhang, Jian; Wu, Gang; Wu, Zhishen

2015-01-01

A comprehensive comparison of macro-strain mode and displacement mode obtained from distributed macro-strain sensing and high-density point sensing (such as accelerometers) technologies is presented in this paper. Theoretical derivation reveals that displacement mode shape from accelerometers and modal macro-strain from distributed macro-strain sensors can be converted into each other. However, it is realized that displacement mode shape as global behavior of a structure can still be calculated with high-precision from modal macro-strain considering measurement errors in practical monitoring, whereas modal macro-strain can hardly be accurately achieved from displacement mode shape when signals are corrupted with noise in practical monitoring. Simulation and experiment results show that the calculated displacement mode shapes are very close to the actual ones even if the noise level reaches 5%. Meanwhile, damage index using measured modal macro-strain is still effective when the measurements are corrupted with 5% noise which is reliable for damage detection in practical monitoring. Calculating modal macro-strain from noise-polluted displacement mode shape will cause an unacceptable error if the noise level reaches only 0.5%, which has been verified in the simulation.

Hydrogeologic characterization and evolution of the 'excavation damaged zone' by statistical analyses of pressure signals: application to galleries excavated at the clay-stone sites of Mont Terri (Ga98) and Tournemire (Ga03)

International Nuclear Information System (INIS)

Fatmi, H.; Ababou, R.; Matray, J.M.; Joly, C.

2010-01-01

Document available in extended abstract form only. This paper presents methods of statistical analysis and interpretation of hydrogeological signals in clayey formations, e.g., pore water pressure and atmospheric pressure. The purpose of these analyses is to characterize the hydraulic behaviour of this type of formation in the case of a deep repository of Mid- Level/High-Level and Long-lived radioactive wastes, and to study the evolution of the geologic formation and its EDZ (Excavation Damaged Zone) during the excavation of galleries. We focus on galleries Ga98 and Ga03 in the sites of Mont Terri (Jura, Switzerland) and Tournemire (France, Aveyron), through data collected in the BPP- 1 and PH2 boreholes, respectively. The Mont Terri site, crossing the Aalenian Opalinus clay-stone, is an underground laboratory managed by an international consortium, namely the Mont Terri project (Switzerland). The Tournemire site, crossing the Toarcian clay-stone, is an Underground Research facility managed by IRSN (France). We have analysed pore water and atmospheric pressure signals at these sites, sometimes in correlation with other data. The methods of analysis are based on the theory of stationary random signals (correlation functions, Fourier spectra, transfer functions, envelopes), and on multi-resolution wavelet analysis (adapted to nonstationary and evolutionary signals). These methods are also combined with filtering techniques, and they can be used for single signals as well as pairs of signals (cross-analyses). The objective of this work is to exploit pressure measurements in selected boreholes from the two compacted clay sites, in order to: - evaluate phenomena affecting the measurements (earth tides, barometric pressures..); - estimate hydraulic properties (specific storage..) of the clay-stones prior to excavation works and compare them with those estimated by pulse or slug tests on shorter time scales; - analyze the effects of drift excavation on pore pressures

Biomolecule detection using a silicon nanoribbon: accumulation mode versus inversion mode

International Nuclear Information System (INIS)

Elfstroem, Niklas; Linnros, Jan

2008-01-01

Silicon nanoribbons were fabricated using standard optical lithography from silicon on insulator material with top silicon layer thicknesses of 100, 60 and 45 nm. Electrically these work as Schottky-barrier field-effect transistors and, depending on the substrate voltage, electron or hole injection is possible. The current through the nanoribbon is extremely sensitive to charge changes at the oxidized top surface and can be used for biomolecule detection in a liquid. We show that for detection of streptavidin molecules the response is larger in the accumulation mode than in the inversion mode, although not leading to higher detection sensitivity due to increased noise. The effect is attributed to the location in depth of the conducting channel, which for holes is closer to the screened surface charges of the biomolecules. Furthermore, the response increases for decreasing silicon thickness in both the accumulation mode and the inversion mode. The results are verified qualitatively and quantitatively through a two-dimensional simulation model on a cross section along the nanoribbon device

Passive harmonic mode locking by mode selection in Fabry-Perot diode lasers with patterned effective index.

Science.gov (United States)

Bitauld, David; Osborne, Simon; O'Brien, Stephen

2010-07-01

We demonstrate passive harmonic mode locking of a quantum-well laser diode designed to support a discrete comb of Fabry-Perot modes. Spectral filtering of the mode spectrum was achieved using a nonperiodic patterning of the cavity effective index. By selecting six modes spaced at twice the fundamental mode spacing, near-transform-limited pulsed output with 2 ps pulse duration was obtained at a repetition rate of 100 GHz.

The H-mode operational window as determined from the ITER H-mode database

International Nuclear Information System (INIS)

Ryter, F.; Kardaun, O.J.W.F.; Stroth, U.

1994-01-01

The H-mode is a promising regime for fusion reactors and it is essential to be able to predict its operational window in future devices. The 'H-Mode Database Working Group' started in 1992 to gather, analyze and compare H-mode threshold data from several divertor tokamaks so that predictions could be made. The database and first results were presented and the threshold database has been improved and extended since. The work has two objectives: 1) to predict the minimum heating power necessary to reach the H-mode in future devices, 2) to contribute to physics studies of the L-H transition. (author) 11 refs., 2 figs

Ultrahigh sensitivity made simple: nanoplasmonic label-free biosensing with an extremely low limit-of-detection for bacterial and cancer diagnostics

Energy Technology Data Exchange (ETDEWEB)

Chen, S; Svedendahl, M; Kaell, M; Gunnarsson, L; Dmitriev, A, E-mail: alexd@chalmers.s [Department of Applied Physics, Chalmers University of Technology, 41296 Goeteborg (Sweden)

2009-10-28

We present a simple and robust scheme for biosensing with an ultralow limit-of-detection down to several pg cm{sup -2} (or several tens of attomoles cm{sup -2}) based on optical label-free biodetection with localized surface plasmon resonances. The scheme utilizes cost-effective optical components and comprises a white light source, a properly functionalized sensor surface enclosed in a simple fluidics chip, and a spectral analyzer. The sensor surface is produced by a bottom-up nanofabrication technique with hole mask colloidal lithography. Despite its simplicity, the method is able to reliably detect protein-protein binding events at low picomolar and femtomolar concentrations, which is exemplified by the label-free detection of the extracellular adherence protein (EAP) found on the outer surface of the bacterium Staphylococcus aureus and of prostate-specific antigen (PSA), which is believed to be a prostate cancer marker. These experiments pave the way towards an ultra-sensitive yet compact biodetection platform for point-of-care diagnostics applications.

Tilting mode in field-reversed configurations

International Nuclear Information System (INIS)

Schwarzmeier, J.L.; Barnes, D.C.; Lewis, H.R.; Seyler, C.E.; Shestakov, A.I.

1982-01-01

Field Reversed Configurations (FRCs) experimentally have exhibited remarkable stability on the magnetohydrodynamic (MHD) timescale, despite numerous MHD calculations showing FRCs to be unstable. It is easy to believe that local modes are stabilized by finite Larmor radius (FLR) effects, but more puzzling is the apparent stability of FRCs against global modes, where one would expect FLR effects to be less important. In this paper we study the tilting mode, which MHD has shown to be a rapidly growing global mode. The tilting mode in FRCs is driven by the pressure gradient, and magnetic compression and field line bending are the stabilizing forces. A schematic of the evolution of the tilting mode is shown. The tilting mode is considered dangerous, because it would lead to rapid tearing across the separatrix. Unlike spheromaks, the tilting mode in FRCs has a separatrix that is fixed in space, so that the mode is strictly internal

Streaming gravity mode instability

International Nuclear Information System (INIS)

Wang Shui.

1989-05-01

In this paper, we study the stability of a current sheet with a sheared flow in a gravitational field which is perpendicular to the magnetic field and plasma flow. This mixing mode caused by a combined role of the sheared flow and gravity is named the streaming gravity mode instability. The conditions of this mode instability are discussed for an ideal four-layer model in the incompressible limit. (author). 5 refs

Discrimination of orbital angular momentum modes of the terahertz vortex beam using a diffractive mode transformer.

Science.gov (United States)

Liu, Changming; Wei, Xuli; Niu, Liting; Wang, Kejia; Yang, Zhengang; Liu, Jinsong

2016-06-13

We present an efficient method to discriminate orbital angular momentum (OAM) of the terahertz (THz) vortex beam using a diffractive mode transformer. The mode transformer performs a log-polar coordinate transformation of the input THz vortex beam, which consists of two 3D-printed diffractive elements. A following lens separates each transformed OAM mode to a different lateral position in its focal plane. This method enables a simultaneous measurement over multiple OAM modes of the THz vortex beam. We experimentally demonstrate the measurement of seven individual OAM modes and two multiplexed OAM modes, which is in good agreement with simulations.

Suppression of an acoustic mode by an elastic mode of a liquid-filled spherical shell resonator.

Science.gov (United States)

Lonzaga, Joel B; Raymond, Jason L; Mobley, Joel; Gaitan, D Felipe

2011-02-01

The purpose of this paper is to report on the suppression of an approximately radial (radially symmetric) acoustic mode by an elastic mode of a water-filled, spherical shell resonator. The resonator, which has a 1-in. wall thickness and a 9.5-in. outer diameter, was externally driven by a small transducer bolted to the external wall. Experiments showed that for the range of drive frequencies (19.7-20.6 kHz) and sound speeds in water (1520-1570 m/s) considered in this paper, a nonradial (radially nonsymmetric) mode was also excited, in addition to the radial mode. Furthermore, as the sound speed in the liquid was changed, the resonance frequency of the nonradial mode crossed with that of the radial one and the amplitude of the latter was greatly reduced near the crossing point. The crossing of the eigenfrequency curves of these two modes was also predicted theoretically. Further calculations demonstrated that while the radial mode is an acoustic one associated with the interior fluid, the nonradial mode is an elastic one associated with the shell. Thus, the suppression of the radial acoustic mode is apparently caused by the overlapping with the nonradial elastic mode near the crossing point.

Informed Design of Mixed-Mode Surveys : Evaluating mode effects on measurement and selection error

NARCIS (Netherlands)

Klausch, Thomas|info:eu-repo/dai/nl/341427306

2014-01-01

“Mixed-mode designs” are innovative types of surveys which combine more than one mode of administration in the same project, such as surveys administered partly on the web (online), on paper, by telephone, or face-to-face. Mixed-mode designs have become increasingly popular in international survey

Influences of multiple low-n modes on n=1 resistive wall mode identification and feedback control

International Nuclear Information System (INIS)

In, Y.; Kim, J.; Kim, J. S.; Garofalo, A. M.; Jackson, G. L.; La Haye, R. J.; Strait, E. J.; Okabayashi, M.; Reimerdes, H.

2008-01-01

It is well known in theory that even after the n=1 resistive wall mode (RWM) is suppressed, the other low-n modes, such as n=2 or 3, can appear sequentially, as β increases. In recent DIII-D experiments [J. L. Luxon, Nucl. Fusion 42, 614 (2002)], we found such an example that supports the theoretical prediction: while the n=1 mode was suppressed, an n=3 mode grew dominant, leading to a β collapse. The n=1 RWM suppression was likely due to a combination of rotational stabilization and n=1 RWM feedback. The multiple RWM identification was performed using an expanded matched filter, where n=1 and n=3 RWM basis vectors are simultaneously considered. Taking advantage of the expanded matched filter, we found that an n=3 mode following an edge-localized-mode burst grew almost linearly for several milliseconds without being hindered. This n=3 mode appeared responsible for the β collapse (down to the n=3 no-wall limit), as well as for a drop in toroidal rotation. A preliminary analysis suggests that the identity of the n=3 mode could be related to the n=3 RWM (possibly the first observation in tokamak experiments), while the impact of the n=3 mode was not as destructive as that of n=1 RWM. A numerical postprocessing of Mirnov probes showed that the n=2 mode was also unstable, consistent with the theoretical prediction. In practice, since the presence of an n=3 mode can interfere with the existing n=1 RWM identification, multiple low-n mode identification is deemed essential not only to detect n>1 mode, but also to provide accurate n=1 RWM identification and feedback control.

A novel MUX/DEMUX based on few-mode FBG for mode division multiplexing system

Science.gov (United States)

Han, Yueyu; Hu, Guijun

2016-05-01

In this paper, a novel mode multiplexer/demultiplexer (MUX/DEMUX) based on few-mode fiber Bragg gratings (FBG) has been proposed. The principle of the MUX/DEMUX based on few-mode FBG has been described in detail, and crosstalk of better than -20 dB is obtained experimentally. Then a 2×2 division multiplexing (MDM) system has been established with the MUX/DEMUX we proposed. The transmission experiment of 2×10 Gbps PRBS has been achieved successfully, which are carried by LP01 mode and LP11 mode, respectively. When the receiver sensitivity is greater than -14 dB m and -10 dB m, the BER can both reach 10-3 for B2B and 10 km transmission, respectively.

Mode-routed fiber-optic add-drop filter

Science.gov (United States)

Moslehi, Behzad (Inventor); Black, Richard James (Inventor); Shaw, Herbert John (Inventor)

2000-01-01

New elements mode-converting two-mode grating and mode-filtering two-mode coupler are disclosed and used as elements in a system for communications, add-drop filtering, and strain sensing. Methods of fabrication for these new two-mode gratings and mode-filtering two-mode couplers are also disclosed.

Fiber cavities with integrated mode matching optics.

Science.gov (United States)

Gulati, Gurpreet Kaur; Takahashi, Hiroki; Podoliak, Nina; Horak, Peter; Keller, Matthias

2017-07-17

In fiber based Fabry-Pérot Cavities (FFPCs), limited spatial mode matching between the cavity mode and input/output modes has been the main hindrance for many applications. We have demonstrated a versatile mode matching method for FFPCs. Our novel design employs an assembly of a graded-index and large core multimode fiber directly spliced to a single mode fiber. This all-fiber assembly transforms the propagating mode of the single mode fiber to match with the mode of a FFPC. As a result, we have measured a mode matching of 90% for a cavity length of ~400 μm. This is a significant improvement compared to conventional FFPCs coupled with just a single mode fiber, especially at long cavity lengths. Adjusting the parameters of the assembly, the fundamental cavity mode can be matched with the mode of almost any single mode fiber, making this approach highly versatile and integrable.

ELM phenomenon as an interaction between bootstrap-current driven peeling modes and pressure-driven ballooning modes

International Nuclear Information System (INIS)

Saarelma, S.; Kurki-Suonio, T.; Guenter, S.; Zehrfeld, H.-P.

2000-01-01

An ELMy ASDEX Upgrade plasma equilibrium is reconstructed taking into account the bootstrap current. The peeling mode stability of the equilibrium is numerically analysed using the GATO [1] code, and it is found that the bootstrap current can drive the plasma peeling mode unstable. A high-n ballooning mode stability analysis of the equilibria revealed that, while destabilizing the peeling modes, the bootstrap current has a stabilizing effect on the ballooning modes. A combination of these two instabilities is a possible explanation for the type I ELM phenomenon. A triangularity scan showed that increasing triangularity stabilizes the peeling modes and can produce ELM-free periods observed in the experiments. (author)

Mode I and mixed mode crack-tip fields in strain gradient plasticity

DEFF Research Database (Denmark)

Goutianos, Stergios

2011-01-01

Strain gradients develop near the crack-tip of Mode I or mixed mode cracks. A finite strain version of the phenomenological strain gradient plasticity theory of Fleck–Hutchinson (2001) is used here to quantify the effect of the material length scales on the crack-tip stress field for a sharp...... stationary crack under Mode I and mixed mode loading. It is found that for material length scales much smaller than the scale of the deformation gradients, the predictions converge to conventional elastic–plastic solutions. For length scales sufficiently large, the predictions converge to elastic solutions....... Thus, the range of length scales over which a strain gradient plasticity model is necessary is identified. The role of each of the three material length scales, incorporated in the multiple length scale theory, in altering the near-tip stress field is systematically studied in order to quantify...

Thermal Operating Modes

International Nuclear Information System (INIS)

Bechtel SAIC Company

2002-01-01

Higher and lower temperature operating modes (e.g., above and below the boiling point of water) are alternative approaches to managing the heat produced by the radioactive decay of spent nuclear fuel. Current analyses indicate that a repository at the Yucca Mountain site is likely to comply with applicable safety standards regardless of the particular thermal operating mode. Both modes have potential advantages and disadvantages. With a higher temperature operating mode (HTOM), waste packages (WPs) can be placed closer together. This reduces the number of drifts, the required emplacement area, construction costs, and occupational risks to construction workers. In addition, the HTOM would minimize the amount of water that might contact the waste for hundreds of years after closure. On the other hand, higher temperatures introduce uncertainties in the understanding of the long-term performance of the repository because of uncertainties in the thermal effects on WP lifetime and the near-field environment around the drifts. A lower temperature operating mode (LTOM) has the potential to reduce uncertainties in long-term performance of the repository by limiting the effects of temperature on WP lifetime and on the near-field environment around the drifts. Depending on the combination of operating parameters, a LTOM could require construction of additional drifts, a larger emplacement area, increased construction costs, increased occupational risks to construction works, and a longer period of ventilation than a HTOM. The repository design for the potential Yucca Mountain site is flexible and can be constructed and operated in various operating modes to achieve specific technical objectives, accommodate future policy decisions, and use of new information. For example, the flexible design can be operated across a range of temperatures and can be tailored to achieve specific thermal requirements in the future. To accommodate future policy decisions, the repository can be

Nonlinear saturation of the trapped-ion mode by mode coupling in two dimensions

International Nuclear Information System (INIS)

Cohen, B.I.; Tang, W.M.

1977-01-01

A study of the nonlinear saturation by mode coupling of the dissipative trapped-ion mode is presented in which both radial and poloidal variations are considered. The saturation mechanism consists of the nonlinear coupling via E x B convection of energy from linearly unstable modes to stable modes. Stabilization is provided at short poloidal wavelengths by Landau damping from trapped and circulating ions, at short radial wavelengths by effects associated with the finite ion banana excursions and at long wavelengths by ion collisions. A one-dimensional, nonlinear partial differential equation for the electrostatic potential derived in earlier work is extended to two dimensions and to third order in amplitude. Included systematically are kinetic effects, e.g., Landau damping and its spatial dependence due to magnetic shear. The stability and accessibility of equilibria are considered in detail for cases far from as well as close to marginal stability. In the first case three-wave interactions are found to be important when the spectrum of unstable modes is sufficiently narrow. In the latter case, it is found that for a single unstable mode, a four-wave interaction can provide the dominant saturation mechanism. Cross-field transport is calculated, and the scaling of results is considered for tokamak parameters

Linear stability of tearing modes

International Nuclear Information System (INIS)

Cowley, S.C.; Kulsrud, R.M.; Hahm, T.S.

1986-05-01

This paper examines the stability of tearing modes in a sheared slab when the width of the tearing layer is much smaller than the ion Larmor radius. The ion response is nonlocal, and the quasineutrality retains its full integal form. An expansion procedure is introduced to solve the quasineutrality equation in powers of the width of the tearing layer over the ion Larmor radius. The expansion procedure is applied to the collisionless and semi-collisional tearing modes. The first order terms in the expansion we find to be strongly stabilizing. The physics of the mode and of the stabilization is discussed. Tearing modes are observed in experiments even though the slab theory predicts stability. It is proposed that these modes grow from an equilibrium with islands at the rational surfaces. If the equilibrium islands are wider than the ion Larmor radius, the mode is unstable when Δ' is positive

Completeness of non-normalizable modes

International Nuclear Information System (INIS)

Mannheim, Philip D; Simbotin, Ionel

2006-01-01

We establish the completeness of some characteristic sets of non-normalizable modes by constructing fully localized square steps out of them, with each such construction expressly displaying the Gibbs phenomenon associated with trying to use a complete basis of modes to fit functions with discontinuous edges. As well as being of interest in and of itself, our study is also of interest to the recently introduced large extra dimension brane-localized gravity program of Randall and Sundrum, since the particular non-normalizable mode bases that we consider (specifically the irregular Bessel functions and the associated Legendre functions of the second kind) are associated with the tensor gravitational fluctuations which occur in those specific brane worlds in which the embedding of a maximally four-symmetric brane in a five-dimensional anti-de Sitter bulk leads to a warp factor which is divergent. Since the brane-world massless four-dimensional graviton has a divergent wavefunction in these particular cases, its resulting lack of normalizability is thus not seen to be any impediment to its belonging to a complete basis of modes, and consequently its lack of normalizability should not be seen as a criterion for not including it in the spectrum of observable modes. Moreover, because the divergent modes we consider form complete bases, we can even construct propagators out of them in which these modes appear as poles with residues which are expressly finite. Thus, even though normalizable modes appear in propagators with residues which are given as their finite normalization constants, non-normalizable modes can just as equally appear in propagators with finite residues too-it is just that such residues will not be associated with bilinear integrals of the modes

Resonant MHD modes with toroidal coupling

International Nuclear Information System (INIS)

Connor, J.W.; Hastie, R.J.; Taylor, J.B.

1990-07-01

This is part 2 of a study of resonant perturbations, such as resistive tearing and ballooning modes, in a torus. These are described by marginal ideal mhd equations in the regions between resonant surfaces; matching across these surfaces provides the dispersion relation. In part 1 we described how all the necessary information from the ideal mhd calculations could be represented by a so-called E-matrix. We also described the calculation of this E-matrix for tearing modes (even parity in perturbed magnetic field) in a large aspect ratio torus. There the toroidal modes comprise coupled cylinder tearing modes and the E-matrix is a generalization of the familiar Δ' quantity in a cylinder. In the present paper we discuss resistive ballooning, or twisting-modes, which have odd-parity in perturbed magnetic field. We show that, unlike the tearing modes, these odd-parity modes are instrinsically toroidal and are not directly related to the odd-parity modes in a cylinder. This is evident from the analysis of the high-n limit in ballooning-space, where a transition from a stable Δ' to an unstable Δ' occurs for the twisting mode when the ballooning effect exceeds the interchange effect, which can occur even at large aspect ratio (as in a tokamak). Analysis of the high-n limit in coordinate space, rather than ballooning space, clarifies this singular behaviour and indicates how one may define twisting-mode Δ'. It also yields a prescription for treating low-n twisting modes and a method for calculating an E-matrix for resistive ballooning modes in a large aspect ratio tokamak. The elements of this matrix are given in terms of cylindrical tearing mode solutions

Mode Equivalence of Health Indicators Between Data Collection Modes and Mixed-Mode Survey Designs in Population-Based Health Interview Surveys for Children and Adolescents: Methodological Study

Science.gov (United States)

Hoffmann, Robert; Houben, Robin; Krause, Laura; Kamtsiuris, Panagiotis; Gößwald, Antje

2018-01-01

Background The implementation of an Internet option in an existing public health interview survey using a mixed-mode design is attractive because of lower costs and faster data availability. Additionally, mixed-mode surveys can increase response rates and improve sample composition. However, mixed-mode designs can increase the risk of measurement error (mode effects). Objective This study aimed to determine whether the prevalence rates or mean values of self- and parent-reported health indicators for children and adolescents aged 0-17 years differ between self-administered paper-based questionnaires (SAQ-paper) and self-administered Web-based questionnaires (SAQ-Web), as well as between a single-mode control group and different mixed-mode groups. Methods Data were collected for a methodological pilot of the third wave of the "German Health Interview and Examination Survey for Children and Adolescents". Questionnaires were completed by parents or adolescents. A population-based sample of 11,140 children and adolescents aged 0-17 years was randomly allocated to 4 survey designs—a single-mode control group with paper-and-pencil questionnaires only (n=970 parents, n=343 adolescents)—and 3 mixed-mode designs, all of which offered Web-based questionnaire options. In the concurrent mixed-mode design, both questionnaires were offered at the same time (n=946 parents, n=290 adolescents); in the sequential mixed-mode design, the SAQ-Web was sent first, followed by the paper questionnaire along with a reminder (n=854 parents, n=269 adolescents); and in the preselect mixed-mode design, both options were offered and the respondents were asked to request the desired type of questionnaire (n=698 parents, n=292 adolescents). In total, 3468 questionnaires of parents of children aged 0-17 years (SAQ-Web: n=708; SAQ-paper: n=2760) and 1194 questionnaires of adolescents aged 11-17 years (SAQ-Web: n=299; SAQ-paper: n=895) were analyzed. Sociodemographic characteristics and a broad

Homogeneous modes of cosmological instantons

International Nuclear Information System (INIS)

Gratton, Steven; Turok, Neil

2001-01-01

We discuss the O(4) invariant perturbation modes of cosmological instantons. These modes are spatially homogeneous in Lorentzian spacetime and thus not relevant to density perturbations. But their properties are important in establishing the meaning of the Euclidean path integral. If negative modes are present, the Euclidean path integral is not well defined, but may nevertheless be useful in an approximate description of the decay of an unstable state. When gravitational dynamics is included, counting negative modes requires a careful treatment of the conformal factor problem. We demonstrate that for an appropriate choice of coordinate on phase space, the second order Euclidean action is bounded below for normalized perturbations and has a finite number of negative modes. We prove that there is a negative mode for many gravitational instantons of the Hawking-Moss or ColemanendashDe Luccia type, and discuss the associated spectral flow. We also investigate Hawking-Turok constrained instantons, which occur in a generic inflationary model. Implementing the regularization and constraint proposed by Kirklin, Turok and Wiseman, we find that those instantons leading to substantial inflation do not possess negative modes. Using an alternate regularization and constraint motivated by reduction from five dimensions, we find a negative mode is present. These investigations shed new light on the suitability of Euclidean quantum gravity as a potential description of our universe

Homogeneous modes of cosmological instantons

Energy Technology Data Exchange (ETDEWEB)

Gratton, Steven; Turok, Neil

2001-06-15

We discuss the O(4) invariant perturbation modes of cosmological instantons. These modes are spatially homogeneous in Lorentzian spacetime and thus not relevant to density perturbations. But their properties are important in establishing the meaning of the Euclidean path integral. If negative modes are present, the Euclidean path integral is not well defined, but may nevertheless be useful in an approximate description of the decay of an unstable state. When gravitational dynamics is included, counting negative modes requires a careful treatment of the conformal factor problem. We demonstrate that for an appropriate choice of coordinate on phase space, the second order Euclidean action is bounded below for normalized perturbations and has a finite number of negative modes. We prove that there is a negative mode for many gravitational instantons of the Hawking-Moss or Coleman{endash}De Luccia type, and discuss the associated spectral flow. We also investigate Hawking-Turok constrained instantons, which occur in a generic inflationary model. Implementing the regularization and constraint proposed by Kirklin, Turok and Wiseman, we find that those instantons leading to substantial inflation do not possess negative modes. Using an alternate regularization and constraint motivated by reduction from five dimensions, we find a negative mode is present. These investigations shed new light on the suitability of Euclidean quantum gravity as a potential description of our universe.

Few-mode erbium-doped fiber amplifier with photonic lantern for pump spatial mode control

NARCIS (Netherlands)

Lopez-Galmiche, G.; Eznaveh, Z. Sanjabi; Antonio-Lopez, J.E.; Benitez, A. M. Velazquez; Rodriguez-Asomoza, Jorge; Mondragon, J. J. Sanchez; Gonnet, C.; Sillard, P.; Li, G.; Schülzgen, A.; Okonkwo, C.M.; Amezcua Correa, R.

2016-01-01

We demonstrate a few-mode erbium-doped fiber amplifier employing a mode-selective photonic lantern for controlling the modal content of the pump light. Amplification of six spatial modes in a 5 m long erbium-doped fiber to x223C;6.2x2009;x2009;dBm average power is obtained while maintaining high

Path planning during combustion mode switch

Science.gov (United States)

Jiang, Li; Ravi, Nikhil

2015-12-29

Systems and methods are provided for transitioning between a first combustion mode and a second combustion mode in an internal combustion engine. A current operating point of the engine is identified and a target operating point for the internal combustion engine in the second combustion mode is also determined. A predefined optimized transition operating point is selected from memory. While operating in the first combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion engine to approach the selected optimized transition operating point. When the engine is operating at the selected optimized transition operating point, the combustion mode is switched from the first combustion mode to the second combustion mode. While operating in the second combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion to approach the target operating point.

Damping Measurements of Plasma Modes

Science.gov (United States)

Anderegg, F.; Affolter, M.; Driscoll, C. F.

2010-11-01

For azimuthally symmetric plasma modes in a magnesium ion plasma, confined in a 3 Tesla Penning-Malmberg trap with a density of n ˜10^7cm-3, we measure a damping rate of 2s-1plasma column, alters the frequency of the mode from 16 KHz to 192 KHz. The oscillatory fluid displacement is small compared to the wavelength of the mode; in contrast, the fluid velocity, δvf, can be large compared to v. The real part of the frequency satisfies a linear dispersion relation. In long thin plasmas (α> 10) these modes are Trivelpiece-Gould (TG) modes, and for smaller values of α they are Dubin spheroidal modes. However the damping appears to be non-linear; initially large waves have weaker exponential damping, which is not yet understood. Recent theoryootnotetextM.W. Anderson and T.M. O'Neil, Phys. Plasmas 14, 112110 (2007). calculates the damping of TG modes expected from viscosity due to ion-ion collisions; but the measured damping, while having a similar temperature and density dependence, is about 40 times larger than calculated. This discrepancy might be due to an external damping mechanism.

Mode division multiplexing over 19-cell hollow-core photonic bandgap fibre by employing integrated mode multiplexer

NARCIS (Netherlands)

Chen, H.; Uden, van R.G.H.; Okonkwo, C.M.; Jung, Y.; Wheeler, N.V.; Fokoua, E.N.; Baddela, N.; Petrovich, M.N.; Poletti, F.; Richardson, D.J.; Raz, O.; Waardt, de H.; Koonen, A.M.J.

2014-01-01

A photonic integrated mode coupler based on silicon-on-insulator is employed for mode division multiplexing (MDM) over a 193 m 19-cell hollow-core photonic bandgap fibre (HC-PBGF) with a -3 dB bandwidth >120 nm. Robust MDM transmissions using LP01 and LP11 modes, and two degenerate LP11 modes (LP11a

Experimental studies of tearing mode and resistive wall mode dynamics in the reversed field pinch configuration

International Nuclear Information System (INIS)

Malmberg, Jenny-Ann

2003-06-01

It is relatively straightforward to establish equilibrium in magnetically confined plasmas, but the plasma is frequently susceptible to a variety of instabilities that are driven by the free energy in the magnetic field or in the pressure gradient. These unstable modes exhibit effects that affect the particle, momentum and heat confinement properties of the configuration. Studies of the dynamics of several of the most important modes are the subject of this thesis. The studies are carried out on plasmas in the reversed field pinch (RFP) configuration. One phenomenon commonly observed in RFPs is mode wall locking. The localized nature of these phase- and wall locked structures results in localized power loads on the wall which are detrimental for confinement. A detailed study of the wall locked mode phenomenon is performed based on magnetic measurements from three RFP devices. The two possible mechanisms for wall locking are investigated. Locking as a result of tearing modes interacting with a static field error and locking due to the presence of a non-ideal boundary. The characteristics of the wall locked mode are qualitatively similar in a device with a conducting shell system (TPE-RX) compared to a device with a resistive shell (Extrap T2). A theoretical model is used for evaluating the threshold values for wall locking due to eddy currents in the vacuum vessel in these devices. A good correlation with experiment is observed for the conducting shell device. The possibility of successfully sustaining discharges in a resistive shell RFP is introduced in the recently rebuilt device Extrap T2R. Fast spontaneous mode rotation is observed, resulting in low magnetic fluctuations, low loop voltage and improved confinement. Wall locking is rarely observed. The low tearing mode amplitudes allow for the theoretically predicted internal non-resonant on-axis resistive wall modes to be observed. These modes have not previously been distinguished due to the formation of wall

ACCA College English Teaching Mode

Science.gov (United States)

Ding, Renlun

2008-01-01

This paper elucidates a new college English teaching mode--"ACCA" (Autonomous Cooperative Class-teaching All-round College English Teaching Mode). Integrated theories such as autonomous learning and cooperative learning into one teaching mode, "ACCA", which is being developed and advanced in practice as well, is the achievement…

Raman amplification of OAM modes

DEFF Research Database (Denmark)

Ingerslev, Kasper; Gregg, Patrick; Galili, Michael

2017-01-01

The set of fibre modes carrying orbital angular momentum (OAM) is a possible basis for mode division multiplexing. In this regard, fibres supporting OAM modes have been fabricated [1], and optical communication using these fibres, has been demonstrated [2]. A vital part of any long range...

Fluorescence quenching and the "ring-mode" to "red-mode" transition in alkali inductively coupled plasmas

Science.gov (United States)

Huang, M.; Bazurto, R.; Camparo, J.

2018-01-01

The ring-mode to red-mode transition in alkali metal inductively coupled plasmas (ICPs) (i.e., rf-discharge lamps) is perhaps the most important physical phenomenon affecting these devices as optical pumping light sources for atomic clocks and magnetometers. It sets the limit on useful ICP operating temperature, thereby setting a limit on ICP light output for atomic-clock/magnetometer signal generation, and it is a temperature region of ICP operation associated with discharge instability. Previous work has suggested that the mechanism driving the ring-mode to red-mode transition is associated with radiation trapping, but definitive experimental evidence validating that hypothesis has been lacking. Based on that hypothesis, one would predict that the introduction of an alkali-fluorescence quenching gas (i.e., N2) into the ICP would increase the ring-mode to red-mode transition temperature. Here, we test that prediction, finding direct evidence supporting the radiation-trapping hypothesis.

Beta limits in H-modes and VH-modes in JET

Energy Technology Data Exchange (ETDEWEB)

Smeulders, P; Hender, T C; Huysmans, G; Marcus, F; Ali-Arshad, S; Alper, B; Balet, B; Bures, M; Deliyanakis, N; Esch, H de; Fshpool, G; Jarvis, O N; Jones, T T.C.; Ketner, W; Koenig, R; Lawson, K; Lomas, P; O` Brien, D; Sadler, G; Stok, D; Stubberfield, P; Thomas, P; Thomen, K; Wesson, J [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Nave, M F [Universidade Tecnica, Lisbon (Portugal). Inst. Superior Tecnico

1994-07-01

In Hot-ion H- and VH-modes, the highest achieved beta was about 10% below the Troyon value in the best case of discharge 26087. The operational space of the high beta discharges obtained before March 1992 has been explored as function of the parameters H{sub ITER89P}, {beta}{sub n}, q{sub 95}, I{sub p}. Also, a limiting envelope on the fusion reactivity as a function of the average plasma pressure and beta has been observed with R{sub DD} related to {beta}{sub {phi}}{sup 2}.B{sub {phi}}{sup 4}. MHD stability analysis shows that the JET VH modes at the edge are in the second region for ballooning mode stability. The dependence of ballooning stability and the n=1 external kink on the edge current density is analyzed. (authors). 6 figs., 6 refs.

Confocal microscopy and spectroscopy of nanocrystals on a high-Q microsphere resonator

International Nuclear Information System (INIS)

Goetzinger, S; Menezes, L de S; Benson, O; Talapin, D V; Gaponik, N; Weller, H; Rogach, A L; Sandoghdar, V

2004-01-01

We report on experiments where we used a home-made confocal microscope to excite single nanocrystals on a high-Q microsphere resonator. In that way spectra of an individual quantum emitter could be recorded. The Q factor of the microspheres coated with nanocrystals was still up to 10 9 . We also demonstrate the use of a prism coupler as a well-defined output port to collect the fluorescence of an ensemble of nanocrystals coupled to whispering-gallery modes

Study of complex modes

International Nuclear Information System (INIS)

Pastrnak, J.W.

1986-01-01

This eighteen-month study has been successful in providing the designer and analyst with qualitative guidelines on the occurrence of complex modes in the dynamics of linear structures, and also in developing computer codes for determining quantitatively which vibration modes are complex and to what degree. The presence of complex modes in a test structure has been verified. Finite element analysis of a structure with non-proportional dumping has been performed. A partial differential equation has been formed to eliminate possible modeling errors

Collective Lyapunov modes

International Nuclear Information System (INIS)

Takeuchi, Kazumasa A; Chaté, Hugues

2013-01-01

We show, using covariant Lyapunov vectors in addition to standard Lyapunov analysis, that there exists a set of collective Lyapunov modes in large chaotic systems exhibiting collective dynamics. Associated with delocalized Lyapunov vectors, they act collectively on the trajectory and hence characterize the instability of its collective dynamics. We further develop, for globally coupled systems, a connection between these collective modes and the Lyapunov modes in the corresponding Perron–Frobenius equation. We thereby address the fundamental question of the effective dimension of collective dynamics and discuss the extensivity of chaos in the presence of collective dynamics. This article is part of a special issue of Journal of Physics A: Mathematical and Theoretical devoted to ‘Lyapunov analysis: from dynamical systems theory to applications’. (paper)

Verification of GENE and GYRO with L-mode and I-mode plasmas in Alcator C-Mod

Science.gov (United States)

Mikkelsen, D. R.; Howard, N. T.; White, A. E.; Creely, A. J.

2018-04-01

Verification comparisons are carried out for L-mode and I-mode plasma conditions in Alcator C-Mod. We compare linear and nonlinear ion-scale calculations by the gyrokinetic codes GENE and GYRO to each other and to the experimental power balance analysis. The two gyrokinetic codes' linear growth rates and real frequencies are in good agreement throughout all the ion temperature gradient mode branches and most of the trapped electron mode branches of the kyρs spectra at r/a = 0.65, 0.7, and 0.8. The shapes of the toroidal mode spectra of heat fluxes in nonlinear simulations are very similar for kyρs ≤ 0.5, but in most cases GENE has a relatively higher heat flux than GYRO at higher mode numbers. The ratio of ion to electron heat flux is similar in the two codes' simulations, but the heat fluxes themselves do not agree in almost all cases. In the I-mode regime, GENE's heat fluxes are ˜3 times those from GYRO, and they are ˜60%-100% higher than GYRO in the L-mode conditions. The GYRO under-prediction of Qe is much reduced in GENE's L-mode simulations, and it is eliminated in the I-mode simulations. This largely improved agreement with the experimental electron heat flux is offset, however, by the large overshoot of GENE's ion heat fluxes, which are 2-3 times the experimental level, and its electron heat flux overshoot at r/a = 0.80 in the I-mode. Rotation effects can explain part of the difference between the two codes' predictions, but very significant differences remain in simulations without any rotation effects.

Interaction of tearing modes

International Nuclear Information System (INIS)

Satya, Y.; Schmidt, G.

1979-01-01

A fully developed tearing mode modifies the magnetic field profile. The effect of this profile modification on the linear growth rate of a different tearing mode in a slab and cylindrical geometry is investigated

Fluxon modes in superconducting multilayers

DEFF Research Database (Denmark)

Pedersen, Niels Falsig; Madsen, Søren Peder

2004-01-01

We show how to construct fluxon modes from plasma modes in the inductively coupled stacked Josephson junctions, and consider some special cases of these fluxon modes analytically. In some cases we can find exact analytical solutions when we choose the bias current in a special way. We also consid...

The energy spectrum of electromagnetic normal modes in dissipative media: modes between two metal half spaces

International Nuclear Information System (INIS)

Sernelius, Bo E

2008-01-01

The energy spectrum of electromagnetic normal modes plays a central role in the theory of the van der Waals and Casimir interaction. Here we study the modes in connection with the van der Waals interaction between two metal half spaces. Neglecting dissipation leads to distinct normal modes with real-valued frequencies. Including dissipation seems to have the effect that these distinct modes move away from the real axis into the complex frequency plane. The summation of the zero-point energies of these modes render a complex-valued result. Using the contour integration, resulting from the use of the generalized argument principle, gives a real-valued and different result. We resolve this contradiction and show that the spectrum of true normal modes forms a continuum with real frequencies

Mode coupling in spin torque oscillators

International Nuclear Information System (INIS)

Zhang, Steven S.-L.; Zhou, Yan; Li, Dong; Heinonen, Olle

2016-01-01

A number of recent experimental works have shown that the dynamics of a single spin torque oscillator can exhibit complex behavior that stems from interactions between two or more modes of the oscillator, such as observed mode-hopping or mode coexistence. There has been some initial work indicating how the theory for a single-mode (macro-spin) spin torque oscillator should be generalized to include several modes and the interactions between them. In the present work, we rigorously derive such a theory starting with the Landau–Lifshitz–Gilbert equation for magnetization dynamics by expanding up to third-order terms in deviation from equilibrium. Our results show how a linear mode coupling, which is necessary for observed mode-hopping to occur, arises through coupling to a magnon bath. The acquired temperature dependence of this coupling implies that the manifold of orbits and fixed points may shift with temperature. - Highlights: • Deriving equations for coupled modes in spin torque oscillators. • Including Hamiltonian formalism and elimination of three–magnon processes. • Thermal bath of magnons central to mode coupling. • Numerical examples of circular and elliptical devices.

Theory of tokamak resistive fishbone modes

International Nuclear Information System (INIS)

Shi Bingren; Sui Guofang

1995-12-01

A special kind of internal kink mode, the fishbone, can be excited by the energetic particles in tokamak plasmas. Theoretical analyses of fishbone modes based on the ideal MHD framework have predicted that two branches of modes exists. One is the Chen-White branch with ω∼ω-bar dm , corresponding to a higher threshold in β h ; the other is the Coppis branch with ω∼ω *i , and a much lower threshold in β h . The latter mode would put a rather unfavourable restriction on heating efficiency and on plasma confinement. However. It is found that the resistivity effect is essential for this mode. In this paper, a new resistive fishbone mode analysis is carried out. In the (γ mhd ,β H ) space, the stability diagram shows complicate structure, the Coppis branch is replaced by a weakly unstable mode and there is no longer closed stable region. The growth rate of this mode varies with β h , its peak value is still very low compared to other internal modes. The implications of these results to future tokamak experiments are discussed. (8 figs.)

Mode coupling in spin torque oscillators

Energy Technology Data Exchange (ETDEWEB)

Zhang, Steven S.-L., E-mail: ZhangShule@missouri.edu [Department of Physics and Astronomy, University of Missouri, Columbia, MO 65211 (United States); Zhou, Yan, E-mail: yanzhou@hku.hk [Department of Physics, The University of Hong Kong, Hong Kong (China); Center of Theoretical and Computational Physics, University of Hong Kong, Hong Kong (China); Li, Dong, E-mail: geodesic.ld@gmail.com [Department of Physics, Centre for Nonlinear Studies, and Beijing-Hong Kong-Singapore Joint Centre for Nonlinear and Complex Systems, Hong Kong Baptist University, Kowloon Tong, Hong Kong (China); Heinonen, Olle, E-mail: heinonen@anl.gov [Material Science Division, Argonne National Laboratory, Lemont, IL 60439 (United States); Northwestern-Argonne Institute of Science and Technology, 2145 Sheridan Road, Evanston, IL 60208 (United States); Computation Institute, The Unversity of Chicago, 5735 S Ellis Avenue, Chicago, IL 60637 (United States)

2016-09-15

A number of recent experimental works have shown that the dynamics of a single spin torque oscillator can exhibit complex behavior that stems from interactions between two or more modes of the oscillator, such as observed mode-hopping or mode coexistence. There has been some initial work indicating how the theory for a single-mode (macro-spin) spin torque oscillator should be generalized to include several modes and the interactions between them. In the present work, we rigorously derive such a theory starting with the Landau–Lifshitz–Gilbert equation for magnetization dynamics by expanding up to third-order terms in deviation from equilibrium. Our results show how a linear mode coupling, which is necessary for observed mode-hopping to occur, arises through coupling to a magnon bath. The acquired temperature dependence of this coupling implies that the manifold of orbits and fixed points may shift with temperature. - Highlights: • Deriving equations for coupled modes in spin torque oscillators. • Including Hamiltonian formalism and elimination of three–magnon processes. • Thermal bath of magnons central to mode coupling. • Numerical examples of circular and elliptical devices.

Probable mode prediction for H.264 advanced video coding P slices using removable SKIP mode distortion estimation

Science.gov (United States)

You, Jongmin; Jeong, Jechang

2010-02-01

The H.264/AVC (advanced video coding) is used in a wide variety of applications including digital broadcasting and mobile applications, because of its high compression efficiency. The variable block mode scheme in H.264/AVC contributes much to its high compression efficiency but causes a selection problem. In general, rate-distortion optimization (RDO) is the optimal mode selection strategy, but it is computationally intensive. For this reason, the H.264/AVC encoder requires a fast mode selection algorithm for use in applications that require low-power and real-time processing. A probable mode prediction algorithm for the H.264/AVC encoder is proposed. To reduce the computational complexity of RDO, the proposed method selects probable modes among all allowed block modes using removable SKIP mode distortion estimation. Removable SKIP mode distortion is used to estimate whether or not a further divided block mode is appropriate for a macroblock. It is calculated using a no-motion reference block with a few computations. Then the proposed method reduces complexity by performing the RDO process only for probable modes. Experimental results show that the proposed algorithm can reduce encoding time by an average of 55.22% without significant visual quality degradation and increased bit rate.

Fused-fiber-based 3-dB mode insensitive power splitters for few-mode optical fiber networks

Science.gov (United States)

Ren, Fang; Huang, Xiaoshan; Wang, Jianping

2017-11-01

We propose a 3-dB mode insensitive power splitter (MIPS) capable of broadcasting and combining optical signals. It is fabricated with two identical few-mode fibers (FMFs) by a heating and pulling technique. The mode-dependent power transfer characteristic as a function of pulling length is investigated. For exploiting its application, we experimentally demonstrate both FMF-based transmissive and reflective star couplers consisting of multiple 3-dB mode insensitive power splitters, which perform broadcasting and routing signals in few-mode optical fiber networks such as mode-division multiplexing (MDM) local area networks using star topology. For experimental demonstration, optical on-off keying signals at 10 Gb/s carried on three spatial modes are successfully processed with open and clear eye diagrams. Measured bit error ratio results show reasonable power penalties. It is found that a reflective star coupler in MDM networks can reduce half of the total amount of required fibers comparing to that of a transmissive star coupler. This MIPS is more efficient, more reliable, more flexible, and more cost-effective for future expansion and application in few-mode optical fiber networks.

Switch mode power supply

International Nuclear Information System (INIS)

Kim, Hui Jun

1993-06-01

This book concentrates on switch mode power supply. It has four parts, which are introduction of switch mode power supply with DC-DC converter such as Buck converter boost converter, Buck-boost converter and PWM control circuit, explanation for SMPS with DC-DC converter modeling and power mode control, resonance converter like resonance switch, converter, multi resonance converter and series resonance and parallel resonance converters, basic test of SMPS with PWM control circuit, Buck converter, Boost converter, flyback converter, forward converter and IC for control circuit.

Nonlinear surface elastic modes in crystals

Science.gov (United States)

Gorentsveig, V. I.; Kivshar, Yu. S.; Kosevich, A. M.; Syrkin, E. S.

1990-03-01

The influence of nonlinearity on shear horizontal surface elastic waves in crystals is described on the basis of the effective nonlinear Schrödinger equation. It is shown that the corresponding solutions form a set of surface modes and the simplest mode coincides with the solution proposed by Mozhaev. The higher order modes have internal frequencies caused by the nonlinearity. All these modes decay in the crystal as uoexp(- z/ zo) atz≫ zo- u o-1 ( z is the distance from the crystal surface, uo the wave amplitude at the surface). The creation of the modes from a localized surface excitation has a threshold. The stability of the modes is discussed.

Mixed-Mode Crack Growth in Wood

Directory of Open Access Journals (Sweden)

Octavian POP

2012-09-01

Full Text Available In timber elements the mixed mode dependsessentially of wood anatomy and load configuration.In these conditions, in order to evaluate the materialbehavior and the fracture process, it’s necessary toseparate the part of each mode. The mixed modeseparation allows evaluating the amplitude offracture mode. In the present paper, using a mixedmodecrack growth specimen made in Douglas fir,the mixed mode crack growth process is studythanks to marks tracking method. Using the markstracking method the characteristic displacementsassociated to opening and shear mode aremeasured. From the experimental measurements,the energy release rate associated to opening andshear modes is calculated into to account the crackadvancement during the test.

Foreign direct investment mode choice : entry and establishment modes in transition economies

NARCIS (Netherlands)

Dikova, Desislava; van Witteloostuijn, Arien

In this study, we bridge two streams of foreign direct investment literature, specifically studies on establishment mode choice (i.e., the choice between an acquisition and a greenfield establishment) and studies on entry mode choice (i.e., the choice between a wholly owned outlet and a subsidiary

Investigation of single-mode and multi-mode hydromagnetic Rayleigh-Taylor instability in planar geometry

International Nuclear Information System (INIS)

Roderick, N.F.; Cochrane, K.; Douglas, M.R.

1998-01-01

Previous investigations carried out to study various methods of seeding the hydromagnetic Rayleigh-Taylor instability in magnetohydrodynamic simulations showed features similar to those seen in hydrodynamic calculations. For periodic single-mode initiations the results showed the appearance of harmonics as the single modes became nonlinear. For periodic multi-mode initiations new modes developed that indicated the presence of mode coupling. The MHD simulations used parameters of the high velocity large radius z-pinch experiments performed in the Z-accelerator at Sandia National Laboratories. The cylindrical convergent geometry and variable acceleration of these configurations made comparison with analytic, developed for planar geometry with constant acceleration, difficult. A set of calculations in planar geometry using constant current to produce acceleration and parameters characteristic of the cylindrical implosions has been performed to allow a better comparison. Results of these calculations, comparison with analytic theory, and comparison with the cylindrical configuration calculations will be discussed

Zero modes and entanglement entropy

Energy Technology Data Exchange (ETDEWEB)

Yazdi, Yasaman K. [Perimeter Institute for Theoretical Physics,31 Caroline St. N., Waterloo, ON, N2L 2Y5 (Canada); Department of Physics and Astronomy, University of Waterloo,200 University Avenue West, Waterloo, ON, N2L 3G1 (Canada)

2017-04-26

Ultraviolet divergences are widely discussed in studies of entanglement entropy. Also present, but much less understood, are infrared divergences due to zero modes in the field theory. In this note, we discuss the importance of carefully handling zero modes in entanglement entropy. We give an explicit example for a chain of harmonic oscillators in 1D, where a mass regulator is necessary to avoid an infrared divergence due to a zero mode. We also comment on a surprising contribution of the zero mode to the UV-scaling of the entanglement entropy.

Mode Combinations and International Operations

DEFF Research Database (Denmark)

Benito, Gabriel R. G.; Petersen, Bent; Welch, Lawrence S.

2011-01-01

reveals that companies tend to combine modes of operation; thereby producing unique foreign operation mode “packages” for given activities and/or countries, and that the packages are liable to be modified over time – providing a potentially important optional path for international expansion. Our data...... key markets (China, UK and USA) as the basis for an exploration of the extent to which, and how and why, companies combine clearly different foreign operation modes. We examine their use of foreign operation mode combinations within given value activities as well as within given countries. The study...

Standardization of Keyword Search Mode

Science.gov (United States)

Su, Di

2010-01-01

In spite of its popularity, keyword search mode has not been standardized. Though information professionals are quick to adapt to various presentations of keyword search mode, novice end-users may find keyword search confusing. This article compares keyword search mode in some major reference databases and calls for standardization. (Contains 3…

The quiescent H-mode regime for high performance edge localized mode-stable operation in future burning plasmas

Energy Technology Data Exchange (ETDEWEB)

Garofalo, A. M., E-mail: garofalo@fusion.gat.com; Burrell, K. H.; Meneghini, O.; Osborne, T. H.; Paz-Soldan, C.; Smith, S. P.; Snyder, P. B.; Turnbull, A. D. [General Atomics, P.O. Box 85608, San Diego, California 92186-5608 (United States); Eldon, D.; Grierson, B. A.; Solomon, W. M. [Princeton Plasma Physics Laboratory, P.O. Box 451, Princeton, New Jersey 08543-0451 (United States); Hanson, J. M. [Columbia University, 2960 Broadway, New York, New York 10027-6900 (United States); Holland, C. [University of California San Diego, 9500 Gilman Dr., La Jolla, California 92093-0417 (United States); Huijsmans, G. T. A.; Liu, F.; Loarte, A. [ITER Organization, Route de Vinon sur Verdon, 13067 St Paul Lez Durance (France); Zeng, L. [University of California Los Angeles, P.O. Box 957099, Los Angeles, California 90095-7099 (United States)

2015-05-15

For the first time, DIII-D experiments have achieved stationary quiescent H-mode (QH-mode) operation for many energy confinement times at simultaneous ITER-relevant values of beta, confinement, and safety factor, in an ITER-like shape. QH-mode provides excellent energy confinement, even at very low plasma rotation, while operating without edge localized modes (ELMs) and with strong impurity transport via the benign edge harmonic oscillation (EHO). By tailoring the plasma shape to improve the edge stability, the QH-mode operating space has also been extended to densities exceeding 80% of the Greenwald limit, overcoming the long-standing low-density limit of QH-mode operation. In the theory, the density range over which the plasma encounters the kink-peeling boundary widens as the plasma cross-section shaping is increased, thus increasing the QH-mode density threshold. The DIII-D results are in excellent agreement with these predictions, and nonlinear magnetohydrodynamic analysis of reconstructed QH-mode equilibria shows unstable low n kink-peeling modes growing to a saturated level, consistent with the theoretical picture of the EHO. Furthermore, high density operation in the QH-mode regime has opened a path to a new, previously predicted region of parameter space, named “Super H-mode” because it is characterized by very high pedestals that can be more than a factor of two above the peeling-ballooning stability limit for similar ELMing H-mode discharges at the same density.

2-LP mode few-mode fiber amplifier employing ring-core erbium-doped fiber.

Science.gov (United States)

Ono, Hirotaka; Hosokawa, Tsukasa; Ichii, Kentaro; Matsuo, Shoichiro; Nasu, Hitoshi; Yamada, Makoto

2015-10-19

A fiber amplifier supporting 2 LP modes that employs a ring-core erbium-doped fiber (RC-EDF) is investigated to reduce differential modal gain (DMG). The inner and outer radii of the ring-core of the RC-EDF are clarified for 2-LP mode operation of the amplifier, and are optimized to reduce the DMG. It is shown that using the overlap integral between the erbium-doped core area and the signal power mode distribution is a good way to optimize the inner and outer radii of the ring-core of the RC-EDF and thus minimize the DMG. A fabricated RC-EDF and a constructed 2-LP mode EDFA are described and a small DMG of around 1 dB is realized for LP01, LP11 and LP21 pumping.

Preconditioned dynamic mode decomposition and mode selection algorithms for large datasets using incremental proper orthogonal decomposition

Science.gov (United States)

Ohmichi, Yuya

2017-07-01

In this letter, we propose a simple and efficient framework of dynamic mode decomposition (DMD) and mode selection for large datasets. The proposed framework explicitly introduces a preconditioning step using an incremental proper orthogonal decomposition (POD) to DMD and mode selection algorithms. By performing the preconditioning step, the DMD and mode selection can be performed with low memory consumption and therefore can be applied to large datasets. Additionally, we propose a simple mode selection algorithm based on a greedy method. The proposed framework is applied to the analysis of three-dimensional flow around a circular cylinder.

Safety analysis for push-mode and rotary-mode core sampling

International Nuclear Information System (INIS)

Milliken, N.J.; Geschke, G.R.

1995-01-01

This safety analysis analyzes using the push-mode core sampling truck in the push-mode and the rotary-mode core sampling trucks in both the push- and rotary-modes to retrieve core samples that, once taken and analyzed, will yield waste characterization data for the hazardous waste tanks at the Hanford Site. Operation of the core sampling trucks in both the push- and rotary-modes was reviewed to determine whether the release of radioactive materials could occur during operation. It was concluded that there are three credible scenarios: a sample spill outside of the tank, a steam release event, and an unfiltered release to the environment during continuous exhauster operation. The probability of a sample spill was found to be 10 -4 /event, the probability of a steam release event was determined to fall in the unlikely range (10 -2 /event to 10 -4 /event), and the probability of an unfiltered release was calculated to be 5 x 10 -3 /year. Typically, events with probabilities of 10 -6 /event or less are not considered to be risk significant, and the consequences usually are not analyzed. The three accident scenarios were analyzed to calculate the dose consequences. It was determined that the steam release event is the bounding accident. The onsite and offsite dose consequences for this event are calculated to be 0.24 Sv (24 rem) and 3.2 x 10 -4 Sv (32 mrem), respectively. These consequences are below the risk acceptance guidelines for an unlikely event, as established in WHC-CM-4-46, Nonreactor Facility Safety Analysis Manual. With the design features and the use of the controls presented in Section 8.0, this operation represents a minimal risk

An FMM-FFT accelerated integral equation solver for characterizing electromagnetic wave propagation in mine tunnels and galleries loaded with conductors

KAUST Repository

Yücel, Abdulkadir C.

2014-07-01

Reliable wireless communication and tracking systems in underground mines are of paramount importance to increase miners\\' productivity while monitoring the environmental conditions and increasing the effectiveness of rescue operations. Key to the design and optimization of such systems are electromagnetic (EM) simulation tools capable of analyzing wave propagation in electromagnetically large mine tunnels and galleries loaded with conducting cables (power, telephone) and mining equipment (trolleys, rails, carts), and potentially partially obstructed by debris from a cave-in. Current tools for simulating EM propagation in mine environments leverage (multi-) modal decompositions (Emslie et. al., IEEE Trans. Antennas Propag., 23, 192-205, 1975; Sun and Akyildiz, IEEE Trans. Commun., 58, 1758-1768, 2010), ray-tracing techniques (Zhang, IEEE Tran. Vehic. Tech., 5, 1308-1314, 2003), or full wave methods. Modal approaches and ray-tracing techniques cannot accurately account for the presence of conductors, intricate details of transmitters/receivers, wall roughness, or unstructured debris from a cave-in. Classical full-wave methods do not suffer from such restrictions. However, they require prohibitively large computational resources when applied to the analysis of electromagnetically large tunnels loaded with conductors. Recently, an efficient hybrid method of moment and transmission line solver has been developed to analyze the EM wave propagation inside tunnels loaded with conductors (Brocker et. al., in Proc IEEE AP-S Symp, pp.1,2, 2012). However, the applicability of the solver is limited to the characterization of EM wave propagation at medium frequency band.

Higher Order Mode Fibers

DEFF Research Database (Denmark)

Israelsen, Stine Møller

This PhD thesis considers higher order modes (HOMs) in optical fibers. That includes their excitation and characteristics. Within the last decades, HOMs have been applied both for space multiplexing in optical communications, group velocity dispersion management and sensing among others......-radial polarization as opposed to the linear polarization of the LP0X modes. The effect is investigated numerically in a double cladding fiber with an outer aircladding using a full vectorial modesolver. Experimentally, the bowtie modes are excited using a long period grating and their free space characteristics...... and polarization state are investigated. For this fiber, the onset of the bowtie effect is shown numerically to be LP011. The characteristics usually associated with Bessel-likes modes such as long diffraction free length and selfhealing are shown to be conserved despite the lack of azimuthal symmetry...

Exploiting selective excitation of strongly coupled modes to reduce DMGD in multi-mode transmission systems

NARCIS (Netherlands)

van Weerdenburg, J.J.A.; Antonio-Lopez, J.E.; Alvarado-Zacarias, J.; Molin, D.; Bigot-Astruc, M.; van Uden, R.; de Waardt, H.; Koonen, A.M.J.; Amezcua-Correa, R.; Sillard, P.; Okonkwo, C.M.

2016-01-01

By exploiting strong coupling in higher-order modes, we experimentally demonstrate reduced differential mode group delay by a factor of 3. Comparing LP02+LP21 with respect to LP01+LP11 3-mode transmission, a 27% reduction in equalizer length is shown after 53.4km MMF transmission.

SEARCH FOR GLOBAL f-MODES AND p-MODES IN THE {sup 8}B NEUTRINO FLUX

Energy Technology Data Exchange (ETDEWEB)

Lopes, Ilídio, E-mail: ilidio.lopes@ist.utl.pt, E-mail: ilopes@uevora.pt [Centro Multidisciplinar de Astrofísica, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Departamento de Física, Escola de Ciências e Tecnologia, Universidade de Évora, Colégio Luis António Verney, 7002-554 Évora (Portugal)

2013-11-01

The impact of global acoustic modes on the {sup 8}B neutrino flux time series is computed for the first time. It is shown that the time fluctuations of the {sup 8}B neutrino flux depend on the amplitude of acoustic eigenfunctions in the region where the {sup 8}B neutrino flux is produced: modes with low n (or order) that have eigenfunctions with a relatively large amplitude in the Sun's core strongly affect the neutrino flux; conversely, modes with high n that have eigenfunctions with a minimal amplitude in the Sun's core have a very small impact on the neutrino flux. It was found that the global modes with a larger impact on the {sup 8}B neutrino flux have a frequency of oscillation in the interval 250 μHz to 500 μHz (or a period in the interval 30 minutes to 70 minutes), such as the f-modes (n = 0) for the low degrees, radial modes of order n ≤ 3, and the dipole mode of order n = 1. Their corresponding neutrino eigenfunctions are very sensitive to the solar inner core and are unaffected by the variability of the external layers of the solar surface. If time variability of neutrinos is observed for these modes, it will lead to new ways of improving the sound speed profile inversion in the central region of the Sun.

A design of a mode converter for electron cyclotron heating by the method of normal mode expansion

International Nuclear Information System (INIS)

Hoshino, Katsumichi; Kawashima, Hisato; Hata, Kenichiro; Yamamoto, Takumi

1983-09-01

Mode conversion of electromagnetic wave propagating in the over-size circular waveguide is attained by giving a periodical perturbation in the guide wall. Mode coupling equation is expressed by ''generalized telegraphist's equations'' which are derived from the Maxwell's equations using a normal mode expansion. A computer code to solve the coupling equations is developed and mode amplitude, conversion efficiency, etc. of a particular type of mode converter for the 60 GHz electron cyclotron heating are obtained. (author)

Surface modes in physics

CERN Document Server

Sernelius, Bo E

2011-01-01

Electromagnetic surface modes are present at all surfaces and interfaces between material of different dielectric properties. These modes have very important effects on numerous physical quantities: adhesion, capillary force, step formation and crystal growth, the Casimir effect etc. They cause surface tension and wetting and they give rise to forces which are important e.g. for the stability of colloids.This book is a useful and elegant approach to the topic, showing how the concept of electromagnetic modes can be developed as a unifying theme for a range of condensed matter physics. The

Detecting mode hopping in single-longitudinal-mode fiber ring lasers based on an unbalanced fiber Michelson interferometer.

Science.gov (United States)

Ma, Mingxiang; Hu, Zhengliang; Xu, Pan; Wang, Wei; Hu, Yongming

2012-10-20

A method of detecting mode hopping for single-longitudinal-mode (SLM) fiber ring lasers has been proposed and experimentally demonstrated. The method that is based on an unbalanced Michelson interferometer (MI) utilizing phase generated carrier modulation instantly transforms mode-hopping dynamics into steep phase changes of the interferometer. Multiform mode hops in an SLM erbium-doped fiber ring laser with an 18.6 MHz mode spacing have been detected exactly in real-time domain and discussed in detail. Numerical results show that the MI-based method has a high testing sensitivity for identifying mode hopping, which will play a significant role in evaluating the output stability of SLM fiber lasers.

Storage facility for radioactive wastes

International Nuclear Information System (INIS)

Okada, Kyo

1998-01-01

Canisters containing high level radioactive wastes are sealed in overpacks in a receiving building constructed on the ground. A plurality of storage pits are formed in a layered manner vertically in multi-stages in deep underground just beneath the receiving building, for example underground of about 1000m from the ground surface. Each of the storage pits is in communication with a shaft which vertically communicates the receiving building and the storage pits, and is extended plainly in a horizontal direction from the shaft. The storage pit comprises an overpack receiving chamber, a main gallery and a plurality of galleries. A plurality of holes for burying the overpacks are formed on the bottom of the galleries in the longitudinal direction of the galleries. A plurality of overpack-positioning devices which run in the main gallery and the galleries by remote operation are disposed in the main gallery and the galleries. (I.N.)

Overlap relation between free-space Laguerre Gaussian modes and step-index fiber modes

CSIR Research Space (South Africa)

Bruning, R

2015-09-01

Full Text Available to control the optical proper- ties of the emerging beam or the excited field distributions at the fiber input. The simplest connection is given by fibers with an parabolic refractive index profile, typical of graded-index fibers, whose modes can be described..., in general free space modes are not suitable to excite selective pure fiber modes and additional beam shaping techniques are required, such as the use of computer generated holograms [5]. The main disadvan- tages of such beam shaping techniques are the low...

Few-mode vertical-cavity surface-emitting laser: Optional emission of transverse modes with different polarizations

Science.gov (United States)

Zhong, Chuyu; Zhang, Xing; Hofmann, Werner; Yu, Lijuan; Liu, Jianguo; Ning, Yongqiang; Wang, Lijun

2018-05-01

Few-mode vertical-cavity surface-emitting lasers that can be controlled to emit certain modes and polarization states simply by changing the biased contacts are proposed and fabricated. By directly etching trenches in the p-doped distributed Bragg reflector, the upper mesa is separated into several submesas above the oxide layer. Individual contacts are then deposited. Each contact is used to control certain transverse modes with different polarization directions emitted from the corresponding submesa. These new devices can be seen as a prototype of compact laser sources in mode division multiplexing communications systems.

Mode Equivalence of Health Indicators Between Data Collection Modes and Mixed-Mode Survey Designs in Population-Based Health Interview Surveys for Children and Adolescents: Methodological Study.

Science.gov (United States)

Mauz, Elvira; Hoffmann, Robert; Houben, Robin; Krause, Laura; Kamtsiuris, Panagiotis; Gößwald, Antje

2018-03-05

The implementation of an Internet option in an existing public health interview survey using a mixed-mode design is attractive because of lower costs and faster data availability. Additionally, mixed-mode surveys can increase response rates and improve sample composition. However, mixed-mode designs can increase the risk of measurement error (mode effects). This study aimed to determine whether the prevalence rates or mean values of self- and parent-reported health indicators for children and adolescents aged 0-17 years differ between self-administered paper-based questionnaires (SAQ-paper) and self-administered Web-based questionnaires (SAQ-Web), as well as between a single-mode control group and different mixed-mode groups. Data were collected for a methodological pilot of the third wave of the "German Health Interview and Examination Survey for Children and Adolescents". Questionnaires were completed by parents or adolescents. A population-based sample of 11,140 children and adolescents aged 0-17 years was randomly allocated to 4 survey designs-a single-mode control group with paper-and-pencil questionnaires only (n=970 parents, n=343 adolescents)-and 3 mixed-mode designs, all of which offered Web-based questionnaire options. In the concurrent mixed-mode design, both questionnaires were offered at the same time (n=946 parents, n=290 adolescents); in the sequential mixed-mode design, the SAQ-Web was sent first, followed by the paper questionnaire along with a reminder (n=854 parents, n=269 adolescents); and in the preselect mixed-mode design, both options were offered and the respondents were asked to request the desired type of questionnaire (n=698 parents, n=292 adolescents). In total, 3468 questionnaires of parents of children aged 0-17 years (SAQ-Web: n=708; SAQ-paper: n=2760) and 1194 questionnaires of adolescents aged 11-17 years (SAQ-Web: n=299; SAQ-paper: n=895) were analyzed. Sociodemographic characteristics and a broad range of health indicators for

Challenges in higher order mode Raman amplifiers

DEFF Research Database (Denmark)

Rottwitt, Karsten; Nielsen, Kristian; Friis, Søren Michael Mørk

2015-01-01

A higher order Raman amplifier model that take random mode coupling into account ispresented. Mode dependent gain and signal power fluctuations at the output of the higher order modeRaman amplifier are discussed......A higher order Raman amplifier model that take random mode coupling into account ispresented. Mode dependent gain and signal power fluctuations at the output of the higher order modeRaman amplifier are discussed...

High degree modes and instrumental effects

Energy Technology Data Exchange (ETDEWEB)

Korzennik, S G [Harvard-Smithsonian Center for Astrophysics, Cambridge, MA (United States); Rabello-Soares, M C; Schou, J [Stanford University, Stanford, CA (United States)], E-mail: skorzennik@cfa.harvard.edu

2008-10-15

Full-disk observations taken with the Michelson Doppler Imager (MDI) on board the Solar and Heliospheric Observatory (SOHO) spacecraft, or the upgraded Global Oscillations Network Group (GONG) instruments, have enough spatial resolution to resolve modes up to {iota} = 1000 if not {iota} = 1500. The inclusion of such high-degree modes (i.e., {iota} {<=} 1000) improves dramatically inferences near the surface. Unfortunately, observational and instrumental effects cause the characterization of high degree modes to be quite complicated. Indeed, the characteristics of the solar acoustic spectrum are such that, for a given order, mode lifetimes get shorter and spatial leaks get closer in frequency as the degree of a mode increases. A direct consequence of this property is that individual modes are resolved only at low and intermediate degrees. At high degrees the individual modes blend into ridges and the power distribution of the ridge defines the ridge central frequency, masking the underlying mode frequency. An accurate model of the amplitude of the peaks that contribute to the ridge power distribution is needed to recover the underlying mode frequency from fitting the ridge. We present a detailed discussion of the modeling of the ridge power distribution, and the contribution of the various observational and instrumental effects on the spatial leakage, in the context of the MDI instrument. We have constructed a physically motivated model (rather than an ad hoc correction scheme) that results in a methodology that can produce unbiased estimates of high-degree modes. This requires that the instrumental characteristics are well understood, a task that has turned out to pose a major challenge. We also present our latest results, where most of the known instrumental and observational effects that affect specifically high-degree modes were removed. These new results allow us to focus our attention on changes with solar activity. Finally, we present variations of mode

Kunstpædagogisk teori og praksis i et didaktisk perspektiv

DEFF Research Database (Denmark)

Illeris, Helene

2010-01-01

This article presents a critical study of the relationship between theory and practice in the field of gallery education within a conceptual framework borrowed from American curriculum theory from the 1970's. Inspired by Elliot Eisner and Elisabeth Vallance's book Conflicting Conceptions...... of Curriculum (1974) the article individuates four conceptions within contemporary gallery education, which are presented within two models: 1. Gallery education based on theories of aesthetic experience, 2. gallery education based on theories of learning and cognition, 3. gallery education based on theories...... of curriculum and ‘Bildung', and 4. gallery education based on theories of social critique and change. In the second part of the article, each of the four conceptions are exemplified through a systematic analysis of two contemporary Nordic or British texts on gallery education. Studies and discussions...

Flowers, fruits, and the abundance of the yellow-chevroned parakeet (Brotogeris chiriri at a gallery forest in the South Pantanal (Brazil Flores, frutos e abundância do periquito-de-asa-amarela (Brotogeris chiriri em uma mata ciliar do Pantanal Sul (Brasil

Directory of Open Access Journals (Sweden)

J. Ragusa-Netto

2004-11-01

Full Text Available Parakeets usually forage for massive and ephemeral plant resources at forest canopies. Fruit pulp is widely cited as a major food resource for these birds, which often eat seeds and nectar. In this study, I assessed flower and fruit production at a gallery forest in the Pantanal flood plain (Brazil in order to evaluate the relationship between food resource production and abundance of a common parakeet, Brotogeris chiriri. Also, I evaluated the relationship between food resource production and foraging activity. Parakeet abundance varied markedly along the year, coinciding with massive episodes of flower and fleshy fruit availability. Inga vera nectar, intensely used during the latter part of dry season, was by far the most exploited food item by parakeets when they were very abundant. The nectar comprised 34% of the parakeets' diet (N = 131 feeding records at the gallery forest, while fleshy fruits made up the rest. Parakeets principally exploited fruits of Cecropia pachystachya and Ficus luschnathiana, besides palm fruits and Inga vera arils. The consistent relationship between foraging activity and parakeet abundance, as well as the coincidence between fluctuations of these parameters and availability of major food resources, suggests that food availability mostly influenced B. chiriri occurrence in the gallery forest. Furthermore, I found no evidence for gallery forest use for roosting and/or breeding, in spite of the fact that such factors usually influence local parakeet abundance.Periquitos normalmente exploram recursos massivos e efêmeros no dossel das florestas tropicais. Dentre os itens alimentares mais utilizados está a polpa de frutos, embora sementes e néctar também sejam consumidos. Neste estudo, foi avaliada a produção de flores e frutos em uma mata ciliar do Pantanal (Brasil e sua relação com a abundância do periquito Brotogeris chiriri. Além disso, avaliaram-se as relações entre a produção de flores e frutos e o

Mode Combinations and International Operations

DEFF Research Database (Denmark)

Benito, Gabriel R. G.; Petersen, Bent; Welch, Lawrence S.

2011-01-01

reveals that companies tend to combine modes of operation; thereby producing unique foreign operation mode “packages” for given activities and/or countries, and that the packages are liable to be modified over time—providing a potentially important optional path for international expansion. The data show...... markets (China, UK and USA) is used as the basis for an exploration of the extent to which, and how and why, companies combine clearly different foreign operation modes. We examine their use of foreign operation mode combinations within given value activities as well as within given countries. The study...

Flexible Microsphere-Embedded Film for Microsphere-Enhanced Raman Spectroscopy.

Science.gov (United States)

Xing, Cheng; Yan, Yinzhou; Feng, Chao; Xu, Jiayu; Dong, Peng; Guan, Wei; Zeng, Yong; Zhao, Yan; Jiang, Yijian

2017-09-27

Dielectric microspheres with extraordinary microscale optical properties, such as photonic nanojets, optical whispering-gallery modes (WGMs), and directional antennas, have drawn interest in many research fields. Microsphere-enhanced Raman spectroscopy (MERS) is an alternative approach for enhanced Raman detection by dielectric microstructures. Unfortunately, fabrication of microsphere monolayer arrays is the major challenge of MERS for practical applications on various specimen surfaces. Here we report a microsphere-embedded film (MF) by immersing a highly refractive microsphere monolayer array in the poly(dimethylsiloxane) (PDMS) film as a flexible MERS sensing platform for one- to three-dimensional (1D to 3D) specimen surfaces. The directional antennas and wave-guided whispering-gallery modes (WG-WGMs) contribute to the majority of Raman enhancement by the MFs. Moreover, the MF can be coupled with surface-enhanced Raman spectroscopy (SERS) to provide an extra >10-fold enhancement. The limit of detection is therefore improved for sensing of crystal violet (CV) and Sudan I molecules in aqueous solutions at concentrations down to 10 -7 M. A hybrid dual-layer microsphere enhancer, constructed by depositing a MF onto a microsphere monolayer array, is also demonstrated, wherein the WG-WGMs become dominant and boost the enhancement ratio >50-fold. The present work opens up new opportunities for design of cost-effective and flexible MERS sensing platforms as individual or associated techniques toward practical applications in ultrasensitive Raman detection.

A Current-Mode Common-Mode Feedback Circuit (CMFB) with Rail-to-Rail Operation

Science.gov (United States)

Suadet, Apirak; Kasemsuwan, Varakorn

2011-03-01

This paper presents a current-mode common-mode feedback (CMFB) circuit with rail-to-rail operation. The CMFB is a stand-alone circuit, which can be connected to any low voltage transconductor without changing or upsetting the existing circuit. The proposed CMFB employs current mirrors, operating as common-mode detector and current amplifier to enhance the loop gain of the CMFB. The circuit employs positive feedback to enhance the output impedance and gain. The circuit has been designed using a 0.18 μm CMOS technology under 1V supply and analyzed using HSPICE with BSIM3V3 device models. A pseudo-differential amplifier using two common sources and the proposed CMFB shows rail to rail output swing (± 0.7 V) with low common-mode gain (-36 dB) and power dissipation of 390 μW.

Gyrokinetic Stability Studies of the Microtearing Mode in the National Spherical Torus Experiment H-mode

International Nuclear Information System (INIS)

Baumgaertel J.A., Redi M.H., Budny R.V., Rewoldt G., Dorland W.

2005-01-01

Insight into plasma microturbulence and transport is being sought using linear simulations of drift waves on the National Spherical Torus Experiment (NSTX), following a study of drift wave modes on the Alcator C-Mod Tokamak. Microturbulence is likely generated by instabilities of drift waves, which cause transport of heat and particles. Understanding this transport is important because the containment of heat and particles is required for the achievement of practical nuclear fusion. Microtearing modes may cause high heat transport through high electron thermal conductivity. It is hoped that microtearing will be stable along with good electron transport in the proposed low collisionality International Thermonuclear Experimental Reactor (ITER). Stability of the microtearing mode is investigated for conditions at mid-radius in a high density NSTX high performance (H-mode) plasma, which is compared to the proposed ITER plasmas. The microtearing mode is driven by the electron temperature gradient, and believed to be mediated by ion collisions and magnetic shear. Calculations are based on input files produced by TRXPL following TRANSP (a time-dependent transport analysis code) analysis. The variability of unstable mode growth rates is examined as a function of ion and electron collisionalities using the parallel gyrokinetic computational code GS2. Results show the microtearing mode stability dependence for a range of plasma collisionalities. Computation verifies analytic predictions that higher collisionalities than in the NSTX experiment increase microtearing instability growth rates, but that the modes are stabilized at the highest values. There is a transition of the dominant mode in the collisionality scan to ion temperature gradient character at both high and low collisionalities. The calculations suggest that plasma electron thermal confinement may be greatly improved in the low-collisionality ITER

Mode-field half-widths of Gaussian approximation for the fundamental mode of two kinds of optical waveguides

International Nuclear Information System (INIS)

Lian-Huang, Li; Fu-Yuan, Guo

2009-01-01

This paper analyzes the characteristic of matching efficiency between the fundamental mode of two kinds of optical waveguides and its Gaussian approximate field. Then, it presents a new method where the mode-field half-width of Gaussian approximation for the fundamental mode should be defined according to the maximal matching efficiency method. The relationship between the mode-field half-width of the Gaussian approximate field obtained from the maximal matching efficiency and normalized frequency is studied; furthermore, two formulas of mode-field half-widths as a function of normalized frequency are proposed

Picturing continuity. The beginnings of the portrait gallery of Cracow bishops in the cloisters of the Franciscan friary in Cracow

Directory of Open Access Journals (Sweden)

Krzysztof J. Czyżewski

2017-12-01

Full Text Available Important type of “group” portraits are likenesses of people connected by blood, holding the same position or representing the same office, shown next to one another, in chronological order. Such portrait galleries, which usually displayed a high degree of uniformity and disregarded the chronological and spatial accuracy, are examples of commemorative paintings. Their primary purpose was to emphasise the lineage and create a picture of unity by simultaneously showing, as a “family” and “house” people who lived in various times, but were united by heredity or succession. In the case of portraits of Catholic clergy, a key role is played by the notion of the Apostolic succession which has guaranteed the continuity in the Church since the times of Christ. The paper deals with (partially surviving group of likenesses of bishops, in the east and south wings of the cloister of the Franciscan friary in Cracow, initiated in the 1430s by Cardinal Zbigniew Oleśnicki, then ordinary bishop of Cracow, 1323–1455. The Franciscan collection likely showed all of Oleśnicki’s predecessors seated next to one another on stone benches, dressed in pontifical garb and identified by means of coats of arms. The founder of the gallery decided that his predecessors be depicted seated, a pose that was considered to be a privileged one, signified the authority of bishops and their role as teachers. The figures of enthroned bishops form a timeless, “ideal” congregation of hierarchs of the local ecclesiastical community. This particular, and fairly rare, arrangement of the representation may have been influenced by the fact that the portraits were painted on walls of cloister walks where, according to the monastic tradition, stone benches were often present. Zbigniew Oleśnicki was well-versed in history and there can be no doubt that he considered himself to be the heir to the accomplishments of all his predecessors and treated their group representation

Limiter H-mode experiments on TFTR

Energy Technology Data Exchange (ETDEWEB)

Bush, C [Oak Ridge National Lab., TN (USA); Bretz, N L; Fredrickson, E D; McGuire, K M; Nazikian, R; Park, H K; Schivell, J; Taylor, G; Bitter, B; Budny, R; Cohen, S A; Kilpatrick, S J; LeBlanc, B; Manos, D M; Meade, D; Paul, S F; Scott, S D; Stratton, B C; Synakowski, E J; Towner, H H; Weiland, R M; Arunasalam, V; Bateman, G; Bell, M G; Bell, R; Boivin, R; Cavallo, A; Cheng, C Z; Chu, T K; Cowl,

1990-12-15

Limiter H-modes with centrally peaked density profiles have been obtained in TFTR using a highly conditioned graphite limiter. The transition to these centrally peaked H-modes takes place from the supershot to the H-mode rather than the usual L- to H-mode transition observed on other tokamaks. Bi-directional beam heating is required to induce the transition. Density peaking factors, n{sub e}(0)/{l angle}n{sub e}{r angle}, >2.3 are obtained and at the same time the H-mode characteristics are similar to those of limiter H-modes on other tokamaks and the global confinement, {tau}{sub E}, can be >2.5 times L-mode scaling. The TRANSP analysis shows that transport in these H-modes is similar to that of supershots within the inner 60 cm of the plasma, but the stored electron energy (calculated using measured values of T{sub e} and n{sub e}) is higher for the H-mode at the plasma edge. Microwave scattering near the edge shows broad spectra at k = 5.5 cm{sup {minus}1} which begin at the drop in D{sub {alpha}} radiation and are strongly shifted in the electron diamagnetic drift direction. At the same time beam emission spectroscopy shows a coherent mode near the boundary with m = 15--20 at 20--30 kHz which is propagating in the ion direction. During an ELM event these apparent rotations cease and Mirnov fluctuations in the 50--500 kHz increase in intensity.

Three mode Er3+ ring-doped fiber amplifier for mode-division multiplexed transmission

NARCIS (Netherlands)

Jung, Y.; Kang, Q.; Sleiffer, V.A.J.M.; Inan, B.; Kuschnerov, M.; Veljanovski, V.; Corbett, B.; Winfield, R.; Li, Z.; Teh, P.S.; Dhar, A.; Sahu, J.K.; Poletti, F.; Alam, S.U.; Richardson, D.J.

2013-01-01

We successfully fabricate three-mode erbium doped fiber with a confined Er3+ doped ring structure and experimentally characterize the amplifier performance with a view to mode-division multiplexed (MDM) transmission. The differential modal gain was effectively mitigated by controlling the relative

Magnetorheological dampers in shear mode

International Nuclear Information System (INIS)

Wereley, N M; Cho, J U; Choi, Y T; Choi, S B

2008-01-01

In this study, three types of shear mode damper using magnetorheological (MR) fluids are theoretically analyzed: linear, rotary drum, and rotary disk dampers. The damping performance of these shear mode MR dampers is characterized in terms of the damping coefficient, which is the ratio of the equivalent viscous damping at field-on status to the damping at field-off status. For these three types of shear mode MR damper, the damping coefficient or dynamic range is derived using three different constitutive models: the Bingham–plastic, biviscous, and Herschel–Bulkley models. The impact of constitutive behavior on shear mode MR dampers is theoretically presented and compared

H-mode study in CHS

International Nuclear Information System (INIS)

Toi, K.; Morisaki, T.; Sakakibara, S.

1995-02-01

In CHS rapid H-mode transition is observed in NBI heated deuterium and hydrogen plasmas without obvious isotope effect, when a net plasma current is ramped up to increase the external rotational transform. The H-mode of CHS has many similarities with those in tokamaks. Recent measurement with fast response Langmuir probes has revealed that the rapid change in floating potential occurs at the transition, but the change follows the formation of edge transport barrier. The presence of ι/2π = 1 surface near the edge and sawtooth crash triggered by internal modes may play an important role for determining the H-mode transition in CHS. (author)

Resonant absorption in semiconductor nanowires and nanowire arrays: Relating leaky waveguide modes to Bloch photonic crystal modes

Energy Technology Data Exchange (ETDEWEB)

Fountaine, Katherine T., E-mail: kfountai@caltech.edu [Department of Chemistry and Chemical Engineering, California Institute of Technology, 1200 E. California Blvd., Pasadena, California 91125 (United States); Joint Center for Artificial Photosynthesis, California Institute of Technology, 1200 E. California Blvd., Pasadena, California 91125 (United States); Whitney, William S. [Joint Center for Artificial Photosynthesis, California Institute of Technology, 1200 E. California Blvd., Pasadena, California 91125 (United States); Department of Physics, California Institute of Technology, 1200 E. California Blvd., Pasadena, California 91125 (United States); Atwater, Harry A. [Joint Center for Artificial Photosynthesis, California Institute of Technology, 1200 E. California Blvd., Pasadena, California 91125 (United States); Department of Applied Physics and Materials Science, California Institute of Technology, 1200 E. California Blvd., Pasadena, California 91125 (United States)

2014-10-21

We present a unified framework for resonant absorption in periodic arrays of high index semiconductor nanowires that combines a leaky waveguide theory perspective and that of photonic crystals supporting Bloch modes, as array density transitions from sparse to dense. Full dispersion relations are calculated for each mode at varying illumination angles using the eigenvalue equation for leaky waveguide modes of an infinite dielectric cylinder. The dispersion relations along with symmetry arguments explain the selectivity of mode excitation and spectral red-shifting of absorption for illumination parallel to the nanowire axis in comparison to perpendicular illumination. Analysis of photonic crystal band dispersion for varying array density illustrates that the modes responsible for resonant nanowire absorption emerge from the leaky waveguide modes.

GATS Mode 4 Negotiation and Policy Options

Directory of Open Access Journals (Sweden)

Kil-Sang Yoo

2004-06-01

Full Text Available This study reviews the characteristics and issues of GATS Mode 4 and guesses the effects of Mode 4 liberalization on Korean economy and labor market to suggest policy options to Korea. Mode 4 negotiation started from the trade perspective, however, since Mode 4 involves international labor migration, it also has migration perspective. Thus developed countries, that have competitiveness in service sector, are interested in free movement of skilled workers such as intra-company transferees and business visitors. On the other hand, developing countries, that have little competitiveness in service sector, are interested in free movement of low-skilled workers. Empirical studies predict that the benefits of Mode 4 liberalization will be focused on developed countries rather than developing countries. The latter may suffer from brain drain and reduction of labor supply. Nevertheless developed countries are reluctant to Mode 4 negotiation because they can utilize skilled workers from developing countries by use of their own temporary visa programs. They are interested in Mode 4 related with Mode 3 in order to ease direct investment and movement of natural persons to developing countries. Regardless of the direction of a single undertaking of Mode 4 negotiation, the net effects of Mode 4 liberalization on Korean economy and labor market may be negative. The Korean initial offer on Mode 4 is the same as the UR offer. Since Korean position on Mode 4 is most defensive, it is hard to expect that Korean position will be accepted as the single undertaking of Mode 4 negotiation. Thus Korea has to prepare strategic package measures to minimize the costs of Mode 4 liberalization and improve competitiveness of service sector.

Acoustic rotation modes in complex plasmas

International Nuclear Information System (INIS)

Bai Dongxue; Wang Zhengxiong; Wang Xiaogang

2004-01-01

Acoustic rotation modes in complex plasmas are investigated in a cylindrical system with an axial symmetry. The linear mode solution is derived. The mode in an infinite area is reduced to a classical dust acoustic wave in the region away from the centre. When the dusty plasma is confined in a finite region, the breathing and rotating-void behaviour are observed. Vivid structures of different mode number solutions are illustrated

Constant-frequency, clamped-mode resonant converters

Science.gov (United States)

Tsai, Fu-Sheng; Materu, Peter; Lee, Fred C.

1987-01-01

Two novel clamped-mode resonant converters are proposed which operate at a constant frequency while retaining many desired features of conventional series- and parallel-resonant converters. State-plane analysis techniques are used to identify all possible operating modes and define their mode boundaries. Control-to-output characteristics are derived that specify the regions for natural and forced commutation. The predicted operating modes are verified using a prototype circuit.

Coupled-mode theory and Fano resonances in guided-mode resonant gratings: the conical diffraction mounting.

Science.gov (United States)

Bykov, Dmitry A; Doskolovich, Leonid L; Soifer, Victor A

2017-01-23

We study resonances of guided-mode resonant gratings in conical mounting. By developing 2D time-dependent coupled-mode theory we obtain simple approximations of the transmission and reflection coefficients. Being functions of the incident light's frequency and in-plane wave vector components, the obtained approximations can be considered as multi-variable generalizations of the Fano line shape. We show that the approximations are in good agreement with the rigorously calculated transmission and reflection spectra. We use the developed theory to investigate angular tolerances of the considered structures and to obtain mode excitation conditions. In particular, we obtain the cross-polarization mode excitation conditions in the case of conical mounting.

Physics of the H-mode

International Nuclear Information System (INIS)

Hinton, F.L.; Chu, M.S.; Dominguez, R.R.

1985-01-01

A theoretical picture of the H-mode is proposed which explains some of the most important features of this good confinement mode in neutral beam heated plasmas with divertors. From consideration of the transport through the separatrix and along the open field lines outside the separatrix, as well as the stability of the plasma inside the separatrix, we show that a bifurcation in the operating parameters is possible. At high edge temperatures, very large particle confinement times are possible because of the Ware pinch. The transport of particles and heat along the open field lines to the divertor region depends on temperature in a non-monotonic way, and the bifurcation of the thermal equilibrium which is implied may correspond to the L- to H-mode transition. The improvement of the interior confinement in the H-mode, when the edge temperature is higher, is shown to follow from the tearing mode stability properties of current profiles with pedestals. (author)

Silicon Chip-to-Chip Mode-Division Multiplexing

DEFF Research Database (Denmark)

Baumann, Jan Markus; Porto da Silva, Edson; Ding, Yunhong

2018-01-01

A chip-to-chip mode-division multiplexing connection is demonstrated using a pair of multiplexers/demultiplexers fabricated on the silicon-on-insulator platform. Successful mode multiplexing and demultiplexing is experimentally demonstrated, using the LP01, LP11a and LP11b modes.......A chip-to-chip mode-division multiplexing connection is demonstrated using a pair of multiplexers/demultiplexers fabricated on the silicon-on-insulator platform. Successful mode multiplexing and demultiplexing is experimentally demonstrated, using the LP01, LP11a and LP11b modes....

Audit mode change, corporate governance

OpenAIRE

Limei Cao; Wanfu Li; Limin Zhang

2015-01-01

This study investigates changes in audit strategy in China following the introduction of risk-based auditing standards rather than an internal control-based audit mode. Specifically, we examine whether auditors are implementing the risk-based audit mode to evaluate corporate governance before distributing audit resources. The results show that under the internal control-based audit mode, the relationship between audit effort and corporate governance was weak. However, implementation of the ri...

Frustration of Bragg reflection by cooperative dual-mode interference: a new mode of optical propagation.

Science.gov (United States)

Yariv, A

1998-12-01

A new optical mode of propagation is described, which is the natural eigenmode (supermode) of a fiber (or any optical waveguide) with two cospatial periodic gratings. The mode frustrates the backward Bragg scattering from the grating by destructive interference of its two constituent submodes (which are eigenmodes of a uniform waveguide). It can be used in a new type of spatial mode conversion in optical guides.

Equilibrium calculations and mode analysis

International Nuclear Information System (INIS)

Herrnegger, F.

1987-01-01

The STEP asymptotic stellarator expansion procedure was used to study the MHD equilibrium and stability properties of stellarator configurations without longitudinal net-current, which also apply to advanced stellarators. The effects of toroidal curvature and magnetic well, and the Shafranov shift were investigated. A classification of unstable modes in toroidal stellarators is given. For WVII-A coil-field configurations having a β value of 1% and a parabolic pressure profile, no free-boundary modes are found. This agrees with the experimental fact that unstable behavior of the plasma column is not observed for this parameter range. So a theoretical β-limit for stability against ideal MHD modes can be estimated by mode analysis for the WVII-A device

Tearing mode instability due to anomalous resistivity

International Nuclear Information System (INIS)

Furuya, Atsushi; Itoh, Sanae I.; Yagi, Masatoshi

2000-01-01

Tearing mode instability in the presence of microscopic truculence is investigates. The effects of microscopic turbulence on tearing mode are taken as drags which are calculated by one-point renormalization method and mean-field approximation. These effects are reduced to effective diffusivities in reduced MHD equations. Using these equations, the stability analyses of the tearing mode are performed. It is shown that a finite amplitude of fluctuation enhances the growth rate of tearing mode. For very high values of turbulent diffusivities, marginally stable state exists. The effects of each turbulent diffusivity on mode stability are examined near marginal stability boundary. Parameter dependence of the resistive ballooning mode turbulence on tearing mode is analyzed as an example. (author)

Analysis of Energy Transmission Modes of Flyback Converter

Directory of Open Access Journals (Sweden)

GONG Shu

2014-08-01

Full Text Available It is of significance to investigate energy transmission modes of a flyback converter for its optimum design. In this paper, the ETMs of a flyback converter are divided into three modes, which are continuous conduction mode-complete inductor supply mode, continuous conduction mode- incomplete inductor supply mode and discontinuous conduction mode-incomplete inductor supply mode, respectively. A deep analysis of the operation is made, a reduction of the boundary condition between the modes is conducted and a comparison of current stress, transformer AP and output ripple voltage between the modes is performed. A 30W prototype is developed and its experiment is done. The experiment results are in agreement with the theoretical analysis quite well.

The evolution of transmission mode

Science.gov (United States)

Forbes, Mark R.; Hauffe, Heidi C.; Kallio, Eva R.; Okamura, Beth; Sait, Steven M.

2017-01-01

This article reviews research on the evolutionary mechanisms leading to different transmission modes. Such modes are often under genetic control of the host or the pathogen, and often in conflict with each other via trade-offs. Transmission modes may vary among pathogen strains and among host populations. Evolutionary changes in transmission mode have been inferred through experimental and phylogenetic studies, including changes in transmission associated with host shifts and with evolution of the unusually complex life cycles of many parasites. Understanding the forces that determine the evolution of particular transmission modes presents a fascinating medley of problems for which there is a lack of good data and often a lack of conceptual understanding or appropriate methodologies. Our best information comes from studies that have been focused on the vertical versus horizontal transmission dichotomy. With other kinds of transitions, theoretical approaches combining epidemiology and population genetics are providing guidelines for determining when and how rapidly new transmission modes may evolve, but these are still in need of empirical investigation and application to particular cases. Obtaining such knowledge is a matter of urgency in relation to extant disease threats. This article is part of the themed issue ‘Opening the black box: re-examining the ecology and evolution of parasite transmission’. PMID:28289251

New Edge Coherent Mode Providing Continuous Transport in Long Pulse H-mode Plasmas

DEFF Research Database (Denmark)

Wang, H.Q.; Xu, G.S.; Wan, B.N.

2014-01-01

An electrostatic coherent mode near the electron diamagnetic frequency (20–90 kHz) is observed in the steep-gradient pedestal region of long pulse H-mode plasmas in the Experimental Advanced Super-conducting Tokamak, using a newly developed dual gas-puff-imaging system and diamond-coated reciproc...

Microwave plasma mode conversion

International Nuclear Information System (INIS)

Torres, H.S.; Sakanaka, P.H.; Villarroel, C.H.

1985-01-01

The behavior of hot electrons during the process of laser-produced plasma is studied. The basic equations of mode conversion from electromagnetic waves to electrostatic waves are presented. It is shown by mode conversion, that, the resonant absorption and parametric instabilities appear simultaneously, but in different plasma regions. (M.C.K.) [pt

Silicon Photonic Integrated Circuit Mode Multiplexer

DEFF Research Database (Denmark)

Ding, Yunhong; Ou, Haiyan; Xu, Jing

2013-01-01

We propose and demonstrate a novel silicon photonic integrated circuit enabling multiplexing of orthogonal modes in a few-mode fiber (FMF). By selectively launching light to four vertical grating couplers, all six orthogonal spatial and polarization modes supported by the FMF are successfully...

The Escherichia coli modE gene: effect of modE mutations on molybdate dependent modA expression.

Science.gov (United States)

McNicholas, P M; Chiang, R C; Gunsalus, R P

1996-11-15

The Escherichia coli modABCD operon, which encodes a high-affinity molybdate uptake system, is transcriptionally regulated in response to molybdate availability by ModE. Here we describe a highly effective enrichment protocol, applicable to any gene with a repressor role, and establish its application in the isolation of transposon mutations in modE. In addition we show that disruption of the ModE C-terminus abolishes derepression in the absence of molybdate, implying this region of ModE controls the repressor activity. Finally, a mutational analysis of a proposed molybdate binding motif indicates that this motif does not function in regulating the repressor activity of ModE.

Spatial mode discriminator based on leaky waveguides

Science.gov (United States)

Xu, Jing; Liu, Jialing; Shi, Hongkang; Chen, Yuntian

2018-06-01

We propose a conceptually simple and experimentally compatible configuration to discriminate the spatial mode based on leaky waveguides, which are inserted in-between the transmission link. The essence of such a spatial mode discriminator is to introduce the leakage of the power flux on purpose for detection. Importantly, the leaky angle of each individual spatial mode with respect to the propagation direction are different for non-degenerated modes, while the radiation patterns of the degenerated spatial modes in the plane perpendicular to the propagation direction are also distinguishable. Based on these two facts, we illustrate the operation principle of the spatial mode discriminators via two concrete examples; a w-type slab leaky waveguide without degeneracy, and a cylindrical leaky waveguide with degeneracy. The correlation between the leakage angle and the spatial mode distribution for a slab leaky waveguide, as well as differences between the in-plane radiation patterns of degenerated modes in a cylindrical leaky waveguide, are verified numerically and analytically. Such findings can be readily useful in discriminating the spatial modes for optical communication or optical sensing.

Equilibrium radionuclide assessment of left ventricular ejection and filling. Comparison of list mode-and multigated frame-mode measurements

Energy Technology Data Exchange (ETDEWEB)

Sugrue, D.D.; McKenna, W.J.; Dickie, S.; Oakley, C.M.; Myers, M.J.; Lavender, J.P. (Royal Postgraduate Medical School, London (UK))

1983-10-01

The relationship as studied between radionuclide indices of left ventricular systolic and diastolic function acquired in conventional multigated frame-mode compared to list-mode in patients with sinus rhythm. The study showed that frame-mode and list-mode measurements of ejection and filling indices are not significantly different in these patients but that backward reformatting of data acquired in list-mode is necessary to measure the atrial contribution to LV stroke counts. It was concluded that valid measurements of left ventricular systolic ejection and diastolic filling can be made in patients in sinus rhythm using frame-mode acquisition with the exception of measurements of the contribution from atrial systole to stroke volume.

Reynolds stress of localized toroidal modes

International Nuclear Information System (INIS)

Zhang, Y.Z.; Mahajan, S.M.

1995-02-01

An investigation of the 2D toroidal eigenmode problem reveals the possibility of a new consistent 2D structure, the dissipative BM-II mode. In contrast to the conventional ballooning mode, the new mode is poloidally localized at π/2 (or -π/2), and possesses significant radial asymmetry. The radial asymmetry, in turn, allows the dissipative BM-II to generate considerably larger Reynolds stress as compared to the standard slab drift type modes. It is also shown that a wide class of localized dissipative toroidal modes are likely to be of the dissipative BM-II nature, suggesting that at the tokamak edge, the fluctuation generated Reynolds stress (a possible source of poloidal flow) can be significant

Reynolds stress of localized toroidal modes

International Nuclear Information System (INIS)

Zhang, Y.Z.; Mahajan, S.M.

1995-01-01

An investigation of the 2D toroidal eigenmode problem reveals the possibility of a new consistent 2D structure, the dissipative BM-II mode. In contrast to the conventional ballooning mode, the new mode is poloidally localized at π/2 (or -π/2), and possesses significant radial asymmetry. The radial asymmetry, in turn, allows the dissipative BM-II to generate considerably larger Reynolds stress as compared to the standard slab drift type modes. It is also shown that a wide class of localized dissipative toroidal modes are likely to be of the dissipative BM-II nature, suggesting that at the tokamak edge, the fluctuation generated Reynolds stress (a possible source of poloidal flow) can be significant. (author). 15 refs

MDM: A Mode Diagram Modeling Framework

DEFF Research Database (Denmark)

Wang, Zheng; Pu, Geguang; Li, Jianwen

2012-01-01

Periodic control systems used in spacecrafts and automotives are usually period-driven and can be decomposed into different modes with each mode representing a system state observed from outside. Such systems may also involve intensive computing in their modes. Despite the fact that such control...

Solar g-modes? Comparison of detected asymptotic g-mode frequencies with solar model predictions

Science.gov (United States)

Wood, Suzannah Rebecca; Guzik, Joyce Ann; Mussack, Katie; Bradley, Paul A.

2018-06-01

After many years of searching for solar gravity modes, Fossat et al. (2017) reported detection of the nearly equally spaced high-order g-modes periods using a 15-year time series of GOLF data from the SOHO spacecraft. Here we report progress towards and challenges associated with calculating and comparing g-mode period predictions for several previously published standard solar models using various abundance mixtures and opacities, as well as the predictions for some non-standard models incorporating early mass loss, and compare with the periods reported by Fossat et al (2017). Additionally, we have a side-by-side comparison of results of different stellar pulsation codes for calculating g-mode predictions. These comparisons will allow for testing of nonstandard physics input that affect the core, including an early more massive Sun and dynamic electron screening.

Mode and climatic factors effect on energy losses in transient heat modes of transmission lines

Science.gov (United States)

Bigun, A. Ya; Sidorov, O. A.; Osipov, D. S.; Girshin, S. S.; Goryunov, V. N.; Petrova, E. V.

2018-01-01

Electrical energy losses increase in modern grids. The losses are connected with an increase in consumption. Existing models of electric power losses estimation considering climatic factors do not allow estimating the cable temperature in real time. Considering weather and mode factors in real time allows to meet effectively and safely the consumer’s needs to minimize energy losses during transmission, to use electric power equipment effectively. These factors increase an interest in the evaluation of the dynamic thermal mode of overhead transmission lines conductors. The article discusses an approximate analytic solution of the heat balance equation in the transient operation mode of overhead lines based on the least squares method. The accuracy of the results obtained is comparable with the results of solving the heat balance equation of transient thermal mode with the Runge-Kutt method. The analysis of mode and climatic factors effect on the cable temperature in a dynamic thermal mode is presented. The calculation of the maximum permissible current for variation of weather conditions is made. The average electric energy losses during the transient process are calculated with the change of wind, air temperature and solar radiation. The parameters having the greatest effect on the transmission capacity are identified.

Predicting the Diversity of Foreign Entry Modes

DEFF Research Database (Denmark)

Hashai, Niron; Geisler Asmussen, Christian; Benito, Gabriel

2007-01-01

diversity across value chain activities and host markets. Analyzing a sample of Israeli based firms we show that larger firms exhibit a higher degree of entry mode diversity both across value chain activities and across host markets. Higher levels of knowledge intensity are also associated with more......This paper expands entry mode literature by referring to multiple modes exerted in different value chain activities within and across host markets, rather than to a single entry mode at the host market level. Scale of operations and knowledge intensity are argued to affect firms' entry mode...... diversity in firms' entry modes across both dimensions....

Mode conversion and its utilization of degenerating surface wave modes on a plasma column

International Nuclear Information System (INIS)

Nonaka, S.; Akao, Y.

1983-01-01

Both mode conversion at degenerating points of dispersion relations for surface wave modes on a discharge plasma column and the methods for their detection and utilization are presented. Mode conversions at three degenerating points become observable by using a surface wave resonator when an azimuthal inhomogeneity of plasma is produced by a static magnetic field of about 1 G applied perpendicular to the column axis. Two of the three detected degenerating points can be utilized for an easy and exact determination of the electron density and its distribution in the discharge tube

Are quantum spin Hall edge modes more resilient to disorder, sample geometry and inelastic scattering than quantum Hall edge modes?

Science.gov (United States)

Mani, Arjun; Benjamin, Colin

2016-04-13

On the surface of 2D topological insulators, 1D quantum spin Hall (QSH) edge modes occur with Dirac-like dispersion. Unlike quantum Hall (QH) edge modes, which occur at high magnetic fields in 2D electron gases, the occurrence of QSH edge modes is due to spin-orbit scattering in the bulk of the material. These QSH edge modes are spin-dependent, and chiral-opposite spins move in opposing directions. Electronic spin has a larger decoherence and relaxation time than charge. In view of this, it is expected that QSH edge modes will be more robust to disorder and inelastic scattering than QH edge modes, which are charge-dependent and spin-unpolarized. However, we notice no such advantage accrues in QSH edge modes when subjected to the same degree of contact disorder and/or inelastic scattering in similar setups as QH edge modes. In fact we observe that QSH edge modes are more susceptible to inelastic scattering and contact disorder than QH edge modes. Furthermore, while a single disordered contact has no effect on QH edge modes, it leads to a finite charge Hall current in the case of QSH edge modes, and thus a vanishing of the pure QSH effect. For more than a single disordered contact while QH states continue to remain immune to disorder, QSH edge modes become more susceptible--the Hall resistance for the QSH effect changes sign with increasing disorder. In the case of many disordered contacts with inelastic scattering included, while quantization of Hall edge modes holds, for QSH edge modes a finite charge Hall current still flows. For QSH edge modes in the inelastic scattering regime we distinguish between two cases: with spin-flip and without spin-flip scattering. Finally, while asymmetry in sample geometry can have a deleterious effect in the QSH case, it has no impact in the QH case.

Are quantum spin Hall edge modes more resilient to disorder, sample geometry and inelastic scattering than quantum Hall edge modes?

International Nuclear Information System (INIS)

Mani, Arjun; Benjamin, Colin

2016-01-01

On the surface of 2D topological insulators, 1D quantum spin Hall (QSH) edge modes occur with Dirac-like dispersion. Unlike quantum Hall (QH) edge modes, which occur at high magnetic fields in 2D electron gases, the occurrence of QSH edge modes is due to spin–orbit scattering in the bulk of the material. These QSH edge modes are spin-dependent, and chiral-opposite spins move in opposing directions. Electronic spin has a larger decoherence and relaxation time than charge. In view of this, it is expected that QSH edge modes will be more robust to disorder and inelastic scattering than QH edge modes, which are charge-dependent and spin-unpolarized. However, we notice no such advantage accrues in QSH edge modes when subjected to the same degree of contact disorder and/or inelastic scattering in similar setups as QH edge modes. In fact we observe that QSH edge modes are more susceptible to inelastic scattering and contact disorder than QH edge modes. Furthermore, while a single disordered contact has no effect on QH edge modes, it leads to a finite charge Hall current in the case of QSH edge modes, and thus a vanishing of the pure QSH effect. For more than a single disordered contact while QH states continue to remain immune to disorder, QSH edge modes become more susceptible—the Hall resistance for the QSH effect changes sign with increasing disorder. In the case of many disordered contacts with inelastic scattering included, while quantization of Hall edge modes holds, for QSH edge modes a finite charge Hall current still flows. For QSH edge modes in the inelastic scattering regime we distinguish between two cases: with spin-flip and without spin-flip scattering. Finally, while asymmetry in sample geometry can have a deleterious effect in the QSH case, it has no impact in the QH case. (paper)

New modes of assisted mechanical ventilation.

Science.gov (United States)

Suarez-Sipmann, F

2014-05-01

Recent major advances in mechanical ventilation have resulted in new exciting modes of assisted ventilation. Compared to traditional ventilation modes such as assisted-controlled ventilation or pressure support ventilation, these new modes offer a number of physiological advantages derived from the improved patient control over the ventilator. By implementing advanced closed-loop control systems and using information on lung mechanics, respiratory muscle function and respiratory drive, these modes are specifically designed to improve patient-ventilator synchrony and reduce the work of breathing. Depending on their specific operational characteristics, these modes can assist spontaneous breathing efforts synchronically in time and magnitude, adapt to changing patient demands, implement automated weaning protocols, and introduce a more physiological variability in the breathing pattern. Clinicians have now the possibility to individualize and optimize ventilatory assistance during the complex transition from fully controlled to spontaneous assisted ventilation. The growing evidence of the physiological and clinical benefits of these new modes is favoring their progressive introduction into clinical practice. Future clinical trials should improve our understanding of these modes and help determine whether the claimed benefits result in better outcomes. Copyright © 2013 Elsevier España, S.L. and SEMICYUC. All rights reserved.

Alcohol sensor based on single-mode-multimode-single-mode fiber structure

Science.gov (United States)

Mefina Yulias, R.; Hatta, A. M.; Sekartedjo, Sekartedjo

2016-11-01

Alcohol sensor based on Single-mode -Multimode-Single-mode (SMS) fiber structure is being proposed to sense alcohol concentration in alcohol-water mixtures. This proposed sensor uses refractive index sensing as its sensing principle. Fabricated SMS fiber structure had 40 m of multimode length. With power input -6 dBm and wavelength 1550 nm, the proposed sensor showed good response with sensitivity 1,983 dB per % v/v with measurement range 05 % v/v and measurement span 0,5% v/v.

Actively mode-locked diode laser with a mode spacing stability of ∼6 × 10{sup -14}

Energy Technology Data Exchange (ETDEWEB)

Zakharyash, V F; Kashirsky, A V; Klementyev, V M [Institute of Laser Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk (Russian Federation)

2015-10-31

We have studied mode spacing stability in an actively mode-locked external-cavity semiconductor laser. It has been shown that, in the case of mode spacing pulling to the frequency of a highly stable external microwave signal produced by a hydrogen standard (stability of 4 × 10{sup -14} over an averaging period τ = 10 s), this configuration ensures a mode spacing stability of 5.92 × 10{sup -14} (τ = 10 s). (control of radiation parameters)

Pedestal structure and stability in H-mode and I-mode: a comparative study on Alcator C-Mod

International Nuclear Information System (INIS)

Hughes, J.W.; Walk, J.R.; Davis, E.M.; LaBombard, B.; Baek, S.G.; Churchill, R.M.; Greenwald, M.; Hubbard, A.E.; Lipschultz, B.; Marmar, E.S.; Reinke, M.L.; Rice, J.E.; Theiler, C.; Terry, J.; White, A.E.; Whyte, D.G.; Snyder, P.B.; Groebner, R.J.; Osborne, T.; Diallo, A.

2013-01-01

New experimental data from the Alcator C-Mod tokamak are used to benchmark predictive modelling of the edge pedestal in various high-confinement regimes, contributing to greater confidence in projection of pedestal height and width in ITER and reactors. ELMy H-modes operate near stability limits for ideal peeling–ballooning modes, as shown by calculations with the ELITE code. Experimental pedestal width in ELMy H-mode scales as the square root of β pol at the pedestal top, i.e. the dependence expected from theory if kinetic ballooning modes (KBMs) were responsible for limiting the pedestal width. A search for KBMs in experiment has revealed a short-wavelength electromagnetic fluctuation in the pedestal that is a candidate driver for inter-edge localized mode (ELM) pedestal regulation. A predictive pedestal model (EPED) has been tested on an extended set of ELMy H-modes from C-Mod, reproducing pedestal height and width reasonably well across the data set, and extending the tested range of EPED to the highest absolute pressures available on any existing tokamak and to within a factor of three of the pedestal pressure targeted for ITER. In addition, C-Mod offers access to two regimes, enhanced D-alpha (EDA) H-mode and I-mode, that have high pedestals, but in which large ELM activity is naturally suppressed and, instead, particle and impurity transport are regulated continuously. Pedestals of EDA H-mode and I-mode discharges are found to be ideal magnetohydrodynamic (MHD) stable with ELITE, consistent with the general absence of ELM activity. Invocation of alternative physics mechanisms may be required to make EPED-like predictions of pedestals in these kinds of intrinsically ELM-suppressed regimes, which would be very beneficial to operation in burning plasma devices. (paper)

Accelerated reliability demonstration under competing failure modes

International Nuclear Information System (INIS)

Luo, Wei; Zhang, Chun-hua; Chen, Xun; Tan, Yuan-yuan

2015-01-01

The conventional reliability demonstration tests are difficult to apply to products with competing failure modes due to the complexity of the lifetime models. This paper develops a testing methodology based on the reliability target allocation for reliability demonstration under competing failure modes at accelerated conditions. The specified reliability at mission time and the risk caused by sampling of the reliability target for products are allocated for each failure mode. The risk caused by degradation measurement fitting of the target for a product involving performance degradation is equally allocated to each degradation failure mode. According to the allocated targets, the accelerated life reliability demonstration test (ALRDT) plans for the failure modes are designed. The accelerated degradation reliability demonstration test plans and the associated ALRDT plans for the degradation failure modes are also designed. Next, the test plan and the decision rules for the products are designed. Additionally, the effects of the discreteness of sample size and accepted number of failures for failure modes on the actual risks caused by sampling for the products are investigated. - Highlights: • Accelerated reliability demonstration under competing failure modes is studied. • The method is based on the reliability target allocation involving the risks. • The test plan for the products is based on the plans for all the failure modes. • Both failure mode and degradation failure modes are considered. • The error of actual risks caused by sampling for the products is small enough

A Bloch mode expansion approach for analyzing quasi-normal modes in open nanophotonic structures

DEFF Research Database (Denmark)

de Lasson, Jakob Rosenkrantz; Kristensen, Philip Trøst; Mørk, Jesper

2014-01-01

We present a new method for determining quasi-normal modes in open nanophotonic structures using a modal ex- pansion technique. The outgoing wave boundary condition of the quasi-normal modes is satisfied automatically without absorbing boundaries, representing a significant advantage compared...

Tearing mode analysis in tokamaks, revisited

International Nuclear Information System (INIS)

Nishimura, Y.; Callen, J.D.; Hegna, C.C.

1997-12-01

A new Δ' shooting code has been developed to investigate tokamak plasma tearing mode stability in a cylinder and large aspect ratio (ε ≤ 0.25) toroidal geometries, neglecting toroidal mode coupling. A different computational algorithm is used (shooting out from the singular surface instead of into it) to resolve the strong singularities at the mode rational surface, particularly in the presence of finite pressure term. Numerical results compare favorably with Furth et al. results. The effects of finite pressure, which are shown to decrease Δ', are discussed. It is shown that the distortion of the flux surfaces by the Shafranov shift, which modifies the geometry metric element stabilizes the tearing mode significantly, even in a low β regime before the toroidal magnetic curvature effects come into play. Double tearing modes in toroidal geometries are examined as well. Furthermore, m ≥ 2 tearing mode stability criteria are compared with three dimensional initial value MHD simulation by the FAR code

Tearing modes in toroidal geometry

International Nuclear Information System (INIS)

Connor, J.W.; Cowley, S.C.; Hastie, R.J.; Hender, T.C.; Hood, A.; Martin, T.J.

1988-01-01

The separation of the cylindrical tearing mode stability problem into a resistive resonant layer calculation and an external marginal ideal magnetohydrodynamic (MHD) calculation (Δ' calculation) is generalized to axisymmetric toroidal geometry. The general structure of this separation is analyzed and the marginal ideal MHD information (the toroidal generalization of Δ') required to discuss stability is isolated. This can then, in principle, be combined with relevant resonant layer calculations to determine tearing mode growth rates in realistic situations. Two examples are given: the first is an analytic treatment of toroidally coupled (m = 1, n = 1) and (m = 2, n = 1) tearing modes in a large aspect ratio torus; the second, a numerical treatment of the toroidal coupling of three tearing modes through finite pressure effects in a large aspect ratio torus. In addition, the use of a coupling integral approach for determining the stability of coupled tearing modes is discussed. Finally, the possibility of using initial value resistive MHD codes in realistic toroidal geometry to determine the necessary information from the ideal MHD marginal solution is discussed

Boundary methods for mode estimation

Science.gov (United States)

Pierson, William E., Jr.; Ulug, Batuhan; Ahalt, Stanley C.

1999-08-01

This paper investigates the use of Boundary Methods (BMs), a collection of tools used for distribution analysis, as a method for estimating the number of modes associated with a given data set. Model order information of this type is required by several pattern recognition applications. The BM technique provides a novel approach to this parameter estimation problem and is comparable in terms of both accuracy and computations to other popular mode estimation techniques currently found in the literature and automatic target recognition applications. This paper explains the methodology used in the BM approach to mode estimation. Also, this paper quickly reviews other common mode estimation techniques and describes the empirical investigation used to explore the relationship of the BM technique to other mode estimation techniques. Specifically, the accuracy and computational efficiency of the BM technique are compared quantitatively to the a mixture of Gaussian (MOG) approach and a k-means approach to model order estimation. The stopping criteria of the MOG and k-means techniques is the Akaike Information Criteria (AIC).