WorldWideScience

Sample records for functionalized carbon black

  1. In vitro toxicity of carbon nanotubes, nano-graphite and carbon black, similar impacts of acid functionalization.

    Science.gov (United States)

    Figarol, Agathe; Pourchez, Jérémie; Boudard, Delphine; Forest, Valérie; Akono, Céline; Tulliani, Jean-Marc; Lecompte, Jean-Pierre; Cottier, Michèle; Bernache-Assollant, Didier; Grosseau, Philippe

    2015-12-25

    Carbon nanotubes (CNT) and nano-graphite (NG) are graphene-based nanomaterials which share exceptional physicochemical properties, but whose health impacts are unfortunately still not well understood. On the other hand, carbon black (CB) is a conventional and widely studied material. The comparison of these three carbon-based nanomaterials is thus of great interest to improve our understanding of their toxicity. An acid functionalization was carried out on CNT, NG and CB so that, after a thorough characterization, their impacts on RAW 264.7 macrophages could be compared for a similar surface chemistry (15 to 120 μg·mL(-1) nanomaterials, 90-min to 24-h contact). Functionalized nanomaterials triggered a weak cytotoxicity similar to the pristine nanomaterials. Acid functionalization increased the pro-inflammatory response except for CB which did not trigger any TNF-α production before or after functionalization, and seemed to strongly decrease the oxidative stress. The toxicological impact of acid functionalization appeared thus to follow a similar trend whatever the carbon-based nanomaterial. At equivalent dose expressed in surface and equivalent surface chemistry, the toxicological responses from murine macrophages to NG were higher than for CNT and CB. It seemed to correspond to the hypothesis of a platelet and fiber paradigm.

  2. Interaction between carboxyl-functionalized carbon black nanoparticles and porous media

    Science.gov (United States)

    Kim, Song-Bae; Kang, Jin-Kyu; Yi, In-Geol

    2015-04-01

    Carbon nanomaterials, such as carbon nanotubes, fullerene, and graphene, have received considerable attention due to their unique physical and chemical characteristics, leading to mass production and widespread application in industrial, commercial, and environmental fields. During their life cycle from production to disposal, however, carbon nanomaterials are inevitably released into water and soil environments, which have resulted in concern about their health and environmental impacts. Carbon black is a nano-sized amorphous carbon powder that typically contains 90-99% elemental carbon. It can be produced from incomplete combustion of hydrocarbons in petroleum and coal. Carbon black is widely used in chemical and industrial products or applications such as ink pigments, coating plastics, the rubber industry, and composite reinforcements. Even though carbon black is strongly hydrophobic and tends to aggregate in water, it can be dispersed in aqueous media through surface functionalization or surfactant use. The aim of this study was therefore to investigate the transport behavior of carboxyl-functionalized carbon black nanoparticles (CBNPs) in porous media. Column experiments were performed for potassium chloride (KCl), a conservative tracer, and CBNPs under saturated flow conditions. Column experiments was conducted in duplicate using quartz sand, iron oxide-coated sand (IOCS), and aluminum oxide-coated sand (AOCS) to examine the effect of metal (Fe, Al) oxide presence on the transport of CBNPs. Breakthrough curves (BTCs) of CBNPs and chloride were obtained by monitoring effluent, and then mass recovery was quantified from these curves. Additionally, interaction energy profiles for CBNP-porous media were calculated using DLVO theory for sphere-plate geometry. The BTCs of chloride had relative peak concentrations ranging from 0.895 to 0.990. Transport parameters (pore-water velocity v, hydrodynamic dispersion coefficient D) obtained by the model fit from the

  3. Black carbon in marine sediments

    NARCIS (Netherlands)

    Middelburg, J.J.; Nieuwenhuize, J.; Van Breugel, P.

    1999-01-01

    Concentrations of black carbon were determined for a number of marine sediments. A comparison of black carbon based on thermal oxidation and hot concentrated nitric acid pretreatments revealed that the latter significantly overestimates combustion derived carbon phases. Black carbon accounts for

  4. SYNTHESIS AND CHARACTERIZATION OF FUNCTIONALIZED CARBON BLACK/POLY(VINYL ALCOHOL) HIGH REFRACTIVE INDEX NANOCOMPOSITES

    Institute of Scientific and Technical Information of China (English)

    Peng-fei Xue; Ji-bin Wang; Yu-bin Bao; Qiu-ying Li; Chi-fei Wu

    2012-01-01

    Carbon black (CB)/polymer composites with high refractive index (RI) were fabricated from poly(vinyl alcohol) (PVA) and covalently functionalized nano-CB (PVA-es-CB) by simple esterification reaction.Transmission electron microscopy showed that uniform aggregates of PVA-es-CB nanoparticles with a size smaller than 100 nm formed in the nanocomposite films.Ellipsometric measurements indicated that the PVA-es-CB/PVA composite films had a RI in the range 1.520-1.598 linearly increased with the PVA-es-CB volume content.Theoretical equation based on Lorentz-Lorenz theory provided reasonably close estimation of the refractive indices to the experimentally observed values.The hybrid films also revealed relatively good surface planarity,thermal stability and optical transparency.

  5. In vitro toxicity of carbon nanotubes, nano-graphite and carbon black, similar impacts of acid functionalization

    OpenAIRE

    Figarol, Agathe,; Pourchez, Jérémie; Boudard, Delphine; Forest, Valérie; Akono, Céline; Tulliani, Jean-Marc; Lecompte, Jean-Pierre; Cottier, Michèle; Bernache-Assolant, Didier; Grosseau, Philippe

    2015-01-01

    International audience; Carbon nanotubes (CNT) and nano-graphite (NG) are graphene-based nanomaterials which share exceptional physicochemical properties, but whose health impacts are unfortunately still not well understood. On the other hand, carbon black (CB) is a conventional and widely studied material. The comparison of these three carbon-based nanomaterials is thus of great interest to improve our understanding of their toxicity. An acid functionalization was carried out on CNT, NG and ...

  6. Carbon black nanoparticles promote the maturation and function of mouse bone marrow-derived dendritic cells.

    Science.gov (United States)

    Koike, Eiko; Takano, Hirohisa; Inoue, Ken-Ichiro; Yanagisawa, Rie; Kobayashi, Takahiro

    2008-09-01

    Particulate matter including carbon black (CB) nanoparticles can enhance antigen-related inflammation and immunoglobulin production in vivo. Dendritic cells (DC) as antigen-presenting cells (APC) are the most capable inducers of immune responses. The present study was designed to determine whether CB nanoparticles affect the maturation/activation and function of DC in vitro. DC were differentiated from bone marrow (BM) cells of BALB/c mice by culture with granulocyte macrophage colony stimulating factor (GM-CSF). At day 8 of culture, BM-derived DC (BMDC) were exposed to CB nanoparticles with a diameter of 14nm or 56nm for 24h. The expression of major histocompatibility complex (MHC) class II, DEC205, CD80, and CD86 (maturation/activation markers of BMDC) was measured by flow cytometry. BMDC function was evaluated by an allogeneic mixed lymphocyte reaction (MLR) assay. CB nanoparticles significantly increased the expression of DEC205 and CD86 in BMDC and tended to increase MHC class II and CD80 expression; however, a size-dependent effect was not observed. On the other hand, BMDC-mediated MLR was significantly enhanced by the CB nanoparticles and the enhancement was greater by 14nm CB nanoparticles than by 56nm CB nanoparticles. Taken together, CB nanoparticles can promote the maturation/activation and function of BMDC, which could be related to their effects on allergic diseases and/or responses. In addition, BMDC-mediated MLR might be useful assay for in vitro screening for adjuvant activity of environmental toxicants.

  7. Surface functional characteristics (C, O, S) of waste tire-derived carbon black before and after steam activation.

    Science.gov (United States)

    Lin, Hsun-Yu; Chen, Wei-Chin; Yuan, Chung-Shin; Hung, Chung-Hsuang

    2008-01-01

    The effects of steam activation on the surface functional characteristics of waste tire-derived carbon black were investigated. Two carbon-based materials, powdered carbon black (PCB) and PCB-derived powdered activated carbon (PCB-PAC), were selected for this study. A stainless steel tubular oven was used to activate the PCB at an activation temperature of 900 degrees C and 1 atm using steam as an activating reagent. X-ray photoelectron spectroscopy (XPS) was adopted to measure the surface composition and chemical structure of carbon surface. Various elemental spectra (C, O, and S) of each carbon sample were further deconvoluted by peak synthesis. Results showed that the surfaces of PCB and PCB-PAC consisted mainly of C-C and C-O. The PCB-PAC surface had a higher percentage of oxygenated functional groups (C=O and O-C=O) than PCB. The O1s spectra show that the oxygen detected on the PCB surface was mainly bonded to carbon (C-O), whereas the oxygen on the PCB-PAC surface could be bonded to hydrogen (O-H) and carbon (C-O). Sulfur on the surface of PCB consisted of 58.9 wt% zinc sulfide (ZnS) and 41.1 wt% S=C=S, whereas that on the surfaces of PCB-PAC consisted mainly of S=C=S. Furthermore, the increase of oxygen content from 9.6% (PCB) to 11.9% (PCB-PAC) resulted in the increase of the pH values of PCB-PAC after steam activation.

  8. Influence of acid functionalization on the cardio-pulmonary toxicity of carbon nanotubes and carbon black in mice

    Science.gov (United States)

    Engineered carbon nanotubes are being developed for a wide range of industrial and medical applications. Because of their unique properties, nanotubes can impose potentially toxic effects, particularly if they have been modified to express functionally reactive chemical groups o...

  9. Climate response to externally mixed black carbon as a function of altitude

    Science.gov (United States)

    Samset, B. H.; Myhre, G.

    2015-04-01

    The climate response to the presence of black carbon (BC) aerosol at a given altitude in the atmosphere is investigated using a global circulation model. The vertical dependence of the efficiency with which BC exerts radiative forcing (RF) through the direct aerosol effect has previously been extensively studied. Here we use the Community Atmosphere Model version 4 atmospheric component of the National Center for Atmospheric Research Community Earth System model version 1.03 to calculate the three-dimensional response to a BC layer inserted at various altitudes. Simulations have been performed both for fixed sea surface temperatures and using a slab ocean setup to include the surface temperature response. We investigate the vertical profiles of RF exerted per gram of externally mixed BC due to both the direct and semidirect aerosol effects. Associated changes in cloud cover, relative humidity, and precipitation are discussed. The precipitation response to BC is decomposed into a fast, stability-related change and a slow, temperature-driven component. We find that while the efficiency of BC to exert positive RF due to the direct effect strengthens with altitude, as in previous studies, it is strongly offset by a negative semidirect effect. The net radiative perturbation of BC at top of atmosphere is found to be positive everywhere below the tropopause and negative above. The global, annual mean precipitation response to BC, after equilibration of a slab ocean, is found to be positive between the surface and 900 hPa but negative at all other altitudes.

  10. Surface analysis of carbon black waste materials from tire residues

    Science.gov (United States)

    Lee, W. H.; Kim, J. Y.; Ko, Y. K.; Reucroft, P. J.; Zondlo, J. W.

    1999-03-01

    X-ray photoelectron spectroscopy (XPS) has been used to obtain surface chemical state information on two carbon black waste materials in terms of the surface element distribution/concentration and chemical structure. Small amounts of sulfur in the form of CS 2 were detected on the surface (less than 1.7 mass %). C-H/C-C was the major carbon functional component on the surface of carbon black samples but other functional forms of carbon were also present such as CO and C-O. The surface of the carbon black obtained from a hydropyrolysis process was highly oxidized primarily in the form of carbon based oxygen groups. On the other hand, surface oxygen atoms on the surface of the carbon black obtained from a pyrolysis process in the absence of H 2 were in the form of both metal oxides and carbon based oxygen groups.

  11. Admix Compatibility in Carbon Black Loaded Toners

    Institute of Scientific and Technical Information of China (English)

    Paul C. Julien

    2004-01-01

    In a xerographic system where the charge on the toner is controlled by the electrical nature of the carbon black used as a pigment, it is found that the speed with which added toner is charged to the proper level depends on the relative electrical negativity of the carbon black in the original and added toner. This is due to the fact that the incumbent toner typically shares its charge with the new toner through charge exchange among the conductive carbon black particles. If the carbon blacks are electrically dissimilar, this charge sharing may fail.Thus, a toner may work well by itself in a machine, but the same toner may fail when added to a machine already running with a toner from a different vendor or even a different lot of toner from the same vendor. Thus the electrical nature of the carbon black needs to be controlled. This can be done by controlling the oxidation of the carbon black.

  12. Phosphate-Doped Carbon Black as Pt Catalyst Support: Co-catalytic Functionality for Dimethyl Ether and Methanol Electro-oxidation

    DEFF Research Database (Denmark)

    Yin, Min; Huang, Yunjie; Li, Qingfeng

    2014-01-01

    Niobium-phosphate-doped (NbP-doped) carbon blacks were prepared as the composite catalyst support for Pt nanoparticles. Functionalities of the composite include intrinsic proton conductivity, surface acidity, and interfacial synergistic interactions with methanol and dimethyl ether (DME......). The supported Pt catalysts show significant improvement in catalytic activity towards the direct oxidation of methanol and DME, attributable to the enhanced adsorption and dehydrogenation of methanol and DME, as well as the presence of activated OH species in the catalysts. The latter is demonstrated...

  13. Investigation of the Interaction between Nafion Ionomer and Surface Functionalized Carbon Black Using Both Ultrasmall Angle X-ray Scattering and Cryo-TEM

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Fan; Xin, Le; Uzunoglu, Aytekin; Qiu, Yang; Stanciu, Lia; Ilavsky, Jan; Li, Wenzhen; Xie, Jian

    2017-02-08

    In making a catalyst ink, the interaction between Nafion ionomer and catalyst support are the key factors that directly affect both ionic conductivity and electronic conductivity of the catalyst layer in a membrane electrode assembly (MEA). One of the major aims of this investigation is to understand the behavior of the catalyst support, Vulcan XC-72 (XC-72) aggregates, in the existence of the Nafion ionomer in a catalyst ink to fill the knowledge gap of the interaction of these components. The dispersion of catalyst ink not only depends on the solvent, but also depends on the interaction of Nafion and carbon particles in the ink. The interaction of Nafion ionomer particles and XC-72 catalyst aggregates in liquid media was studied using ultra small angle x-ray scattering (USAXS) and cryogenic TEM techniques. Carbon black XC-72) and functionalized carbon black systems were introduced to study the interaction behaviors. A multiple curve fitting was used to extract the particle size and size distribution from scattering data. The results suggest that the particle size and size distribution of each system changed significantly in Nafion + XC-72 system, Nafion + NH2-XC72 system, and Nafion + SO3H-XC-72 system, which indicates that an interaction among these components (i.e. ionomer particles and XC-72 aggregates) exists. The cryogenic TEM, which allows for the observation the size of particles in a liquid, was used to validate the scattering results and shows excellent agreement.

  14. Black carbon and organic carbon emissions from wildfires in Mexico

    OpenAIRE

    XÓCHITL CRUZ NÚÑEZ; LOURDES VILLERS RUIZ; CARLOS GAY GARCÍA

    2014-01-01

    In Mexico, approximately 7650 wildfires occur annually, affecting 263 115 hectares of land. In addition to their impact on land degradation, wildfires cause deforestation, damage to ecosystems and promote land use change; apart from being the source of emissions of toxic substances to the environment (i.e., hydrogen cya - nide, black carbon and organic carbon). Black carbon is a short-lived greenhouse pollutant that also promotes snow and ice melting and decreased rainfall; it has an estimate...

  15. Study on the electric conduction function of carbon black and carbon fiber diphasic electrically conductive concrete%炭黑碳纤维复相导电混凝土的导电性能研究

    Institute of Scientific and Technical Information of China (English)

    卢珍; 吴献; 杨昆

    2014-01-01

    It aimed at the research on the electric conduction function carbon black and carbon fiber diphasic electrically conductive concrete,and analyse the change of resistivity.The methodology adopted as theoretical basis and experimental basis can be used in deicing or snow-melting in future.Carbon black and carbon fiber as the electric conduction is used to improve the electric conduction function of concrete.Conduct the experiment of the electric conduction function of carbon black and carbon fiber diphasic electrically conductive con-crete.The effect of temperature,humidity and plus voltage on resistivity of carbon black and carbon fiber diphasic electricall conductive concrete was analysed.When environment chang,the electric conduction function of concrete will chang too.As the rise of temperature the experimental results showed that the resistivity of carbon black and carbon fiber diphasic electrically conductive concrete will reduct in a certain degree.The resistivity in dry state was higher than the state of wet. As the rise of plus voltage the resistivity of carbon black and car-bon fiber diphasic electrically conductive concrete will reduct in a certain degree.When the voltage is to a certain number ,the resistivity trend to be stabile.%研究了炭黑碳纤维复相导电混凝土的导电性能,分析了导电混凝土的电阻率变化,为实际应用于道路融雪化冰提供理论依据与试验依据。利用纳米导电炭黑和碳纤维作为导电相来改善混凝土的导电性能,进行炭黑碳纤维复相导电混凝土的导电性能试验,分析环境温度、干湿度和外加电压对炭黑碳纤维导电混凝土电阻率的影响。导电混凝土的电阻率受温度、湿度和外加电压的影响,当环境条件发生变化时,导电混凝土的导电性能也会发生变化。炭黑碳纤维复相导电混凝土的电阻率随着温度的升高出现一定程度的减小;干燥状态下的电阻率高于潮湿

  16. Soil Black Carbon Loss and Sediment Black Carbon Accumulation in a Central Texas Woodland

    Science.gov (United States)

    Schieve, E. A.; Hockaday, W. C.; White, J. D.

    2016-12-01

    The Balcones Canyonlands National Wildlife Refuge is located along the eastern edge of the Edwards Plateau in Texas, and was established in 1992 for the purpose of conserving habitat for two endangered bird species. The landscape is composed of hilly, mesa-valley terrain, which is mostly covered by grasslands and woodlands dominated by juniper with intermingling of various oak species. Based on historical photo analysis and tree fire scar dendrochronology, the area has experienced major land use changes over the last century due to wildfire, logging, and drought affecting soil stability and woodland species composition. A previous study on soil black carbon showed that site-specific soil erosion potential and time since last fire may act as controls on soil black carbon concentrations. However, the black carbon transport flux, depositional fate, or the magnitude of soil erosion effects upon the black carbon budget are unconstrained at the watershed scale. To address this, we sampled the sediments accumulating in small ponds constructed during the 1950's for livestock watering. We are quantifying black carbon in sediments using solid-state 13C nuclear magnetic resonance spectroscopy. Preliminary data suggest that the pond sediments are a black carbon sink. Black carbon comprises 15 % - 25 %, of the sedimentary organic carbon, as substantial enrichment relative to soils within the watershed. We will present an early assessment of the black carbon erosion and sediment accumulation rates in first- and second-order watersheds.

  17. Black carbon in deep-Sea sediments

    Science.gov (United States)

    Masiello; Druffel

    1998-06-19

    Black carbon (BC) enters the ocean through aerosol and river deposition. BC makes up 12 to 31 percent of the sedimentary organic carbon (SOC) at two deep ocean sites, and it is 2400 to 13,900 carbon-14 years older than non-BC SOC deposited concurrently. BC is likely older because it is stored in an intermediate reservoir before sedimentary deposition. Possible intermediate pools are oceanic dissolved organic carbon (DOC) and terrestrial soils. If DOC is the intermediate reservoir, then BC is 4 to 22 percent of the DOC pool. If soils are the intermediate reservoir, then the importance of riverine carbon in the ocean carbon cycle has been underestimated.

  18. Preparation, characterization and evaluation of electrocatalysts supported on functionalized carbon black for polymer exchange membrane fuel cell applications; Preparacao, caracterizacao e avaliacao de eletrocatalisadores suportados em carbono funcionalizado para aplicacao em celulas a combustivel tipo PEM

    Energy Technology Data Exchange (ETDEWEB)

    Carmo, Marcelo do

    2008-12-18

    The fuel cell technology associated with the growing exigency of low environmental impact energy became prosperous in the world energy scenery. The fuel cell is basically a device that converts directly the chemical energy of a fuel into electrical and thermal energy with a continuous operation by the constant feed of a fuel. Especially, the carbon black Vulcan XC72 is usually employed as an electro catalyst support, and some factors as an accessible and high surface area in order to get maximum particles dispersion, pore size, adequate pore distribution and the presence of functional groups in the carbon black surface are considered fundamental characteristics for an innovative materials development. However, the Vulcan XC72 still reveals insufficient conditions for these purposes. This study consists in the preparation and in the physical chemical characterization of functionalized carbon black by hydrogen peroxide and by polymeric chains with proton conduction properties, and its posterior utilization as electro catalyst support for PEMFC and DMFC application. After the carbon functionalization, an improvement in the carbon black dispersion in water media was observed, a beneficial effect for electro catalyst preparation. It was also observed, that the functional groups and the polymeric chains worked as stabilizers in the particle growing, producing much more homogeneous electrocatalysts, exhibiting smaller average particle size. Especially, in the case of polymeric chains functionalization, a decrease in the ohmic drop was observed for this system, attributed to an improvement in the proton transference. (author)

  19. Simulations of phenol adsorption on activated carbon and carbon black

    OpenAIRE

    Prosenjak, Claudia; Valente Nabais, Joao; Laginhas, Carlos; Carrott, Peter; Carrott, Manuela

    2010-01-01

    We use grand canonical Monte Carlo and molecular dynamics simulations to study the adsorption of phenol on carbon materials. Activated carbon is modelled by pore size distributions based on DFT methods; carbon black is represented by a single carbon slab with varying percentages of surface atoms removed. GCMC results for the adsorption from the corresponding gas phase gave reasonable agreement with experimental adsorption results. MD simulations, that studied the influence of the presence of ...

  20. Pyrolytic carbon black composite and method of making the same

    Energy Technology Data Exchange (ETDEWEB)

    Naskar, Amit K.; Paranthaman, Mariappan Parans; Bi, Zhonghe

    2016-09-13

    A method of recovering carbon black includes the step of providing a carbonaceous source material containing carbon black. The carbonaceous source material is contacted with a sulfonation bath to produce a sulfonated material. The sulfonated material is pyrolyzed to produce a carbon black containing product comprising a glassy carbon matrix phase having carbon black dispersed therein. A method of making a battery electrode is also disclosed.

  1. Geolocating Russian sources for Arctic black carbon

    Science.gov (United States)

    Cheng, Meng-Dawn

    2014-08-01

    To design and implement an effective emission control strategy for black carbon (BC), the locations and strength of BC sources must be identified. Lack of accurate source information from the Russian Federation has created difficulty for a range of research and policy activities in the Arctic because Russia occupies the largest landmass in the Arctic Circle. A project was initiated to resolve emission sources of BC in the Russian Federation by using the Potential Source Contribution Function (PSCF). It used atmospheric BC data from two Arctic sampling stations at Alert Nunavut, Canada, and Tiksi Bay, Russia. The geographical regions of BC emission sources in Russia were identified and summarized as follows: (1) a region surrounding Moscow, (2) regions in Eurasia stretching along the Ural Mountains from the White Sea to the Black Sea, and (3) a number of scattered areas from western Siberia to the Russian Far East. Particulate potassium ions, non-marine sulfate, and vanadium were used to assist in resolving the source types: forest fire/biomass burning, coal-fired power plant, and oil combustion. Correlating these maps with the BC map helped to resolve source regions of BC emissions and connect them to their corresponding source types. The results imply that a region south of Moscow and another north of the Ural Mountains could be significant BC sources, but none of the grid cells in these regions could be linked to forest fires, oil combustion, or coal-fired power plants based on these three markers.

  2. Studies of activated carbon and carbon black for supercapacitor applications

    Energy Technology Data Exchange (ETDEWEB)

    Richner, R.; Mueller, S.; Koetz, R.; Wokaun, A. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    Carbon Black and activated carbon materials providing high surface areas and a distinct pore distribution are prime materials for supercapacitor applications at frequencies < 0.5 Hz. A number of these materials were tested for their specific capacitance, surface and pore size distribution. High capacitance electrodes were manufactured on the laboratory scale with attention to ease of processability. (author) 1 fig., 1 ref.

  3. Black carbon in deep-sea sediments

    OpenAIRE

    1998-01-01

    Black carbon (BC) enters the ocean through aerosol and river deposition. BC makes up 12 to 31 percent of the sedimentary organic carbon (SOC) at two deep ocean sites, and it is 2400 to 13,900 carbon-14 years older than non-BC SOC deposited concurrently. BC is likely older because it is stored in an intermediate reservoir before sedimentary deposition. Possible intermediate pools are oceanic dissolved organic carbon (DOC) and terrestrial soils. If DOC is the intermediate reservoir, then BC is ...

  4. Are there "black holes" in carbonate deposystems?

    OpenAIRE

    Wright, V.P.; Cherns, L.

    2009-01-01

    The likelihood that extensive dissolution of aragonite (and high magnesian calcite) takes place during very early burial, even in relatively shallow tropical settings, has wide implications for interpreting and modelling ancient limestones. Some low energy environments may constitute net sinks (“black holes”) for carbonates. If this is the case attempts to model sediment budgets and develop depth-productivity profiles for carbonate systems require as yet unavailable quantitative data on the e...

  5. Black carbon in aerosol during BIBLE B

    Science.gov (United States)

    Liley, J. Ben; Baumgardner, D.; Kondo, Y.; Kita, K.; Blake, D. R.; Koike, M.; Machida, T.; Takegawa, N.; Kawakami, S.; Shirai, T.; Ogawa, T.

    2003-02-01

    The Biomass Burning and Lightning Experiment (BIBLE) A and B campaigns over the tropical western Pacific during springtime deployed a Gulfstream-II aircraft with systems to measure ozone and numerous precursor species. Aerosol measuring systems included a MASP optical particle counter, a condensation nucleus (CN) counter, and an absorption spectrometer for black carbon. Aerosol volume was very low in the middle and upper troposphere during both campaigns, and during BIBLE A, there was little aerosol enhancement in the boundary layer away from urban areas. In BIBLE B, there was marked aerosol enhancement in the lowest 3 km of the atmosphere. Mixing ratios of CN in cloud-free conditions in the upper troposphere were in general higher than in the boundary layer, indicating new particle formation from gaseous precursors. High concentrations of black carbon were observed during BIBLE B, with mass loadings up to 40 μg m-3 representing as much as one quarter of total aerosol mass. Strong correlations with hydrocarbon enhancement allow the determination of a black carbon emission ratio for the fires at that time. Expressed as elemental carbon, it is about 0.5% of carbon dioxide and 6% of carbon monoxide emissions from the same fires, comparable to methane production, and greater than that of other hydrocarbons.

  6. Modified carbon black materials for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Kostecki, Robert; Richardson, Thomas; Boesenberg, Ulrike; Pollak, Elad; Lux, Simon

    2016-06-14

    A lithium (Li) ion battery comprising a cathode, a separator, an organic electrolyte, an anode, and a carbon black conductive additive, wherein the carbon black has been heated treated in a CO.sub.2 gas environment at a temperature range of between 875-925 degrees Celsius for a time range of between 50 to 70 minutes to oxidize the carbon black and reduce an electrochemical reactivity of the carbon black towards the organic electrolyte.

  7. Black Carbon, The Pyrogenic Clay Mineral?

    Science.gov (United States)

    Most soils contain significant amounts of black carbon, much of which is present as discrete particles admixed with the coarse clay fraction (0.2–2.0 µm e.s.d.) and can be physically separated from the more abundant diffuse biogenic humic materials. Recent evidence has shown that naturally occurring...

  8. Black carbon: The reverse of its dark side

    NARCIS (Netherlands)

    Koelmans, A.A.; Jonker, M.T.O.; Cornelissen, G.; Bucheli, T.D.; Noort, van P.C.M.; Gustafsson, O.

    2006-01-01

    The emission of black carbon is known to cause major environmental problems. Black carbon particles contribute to global warming, carry carcinogenic compounds and cause serious health risks. Here, we show another side of the coin. We review evidence that black carbon may strongly reduce the risk pos

  9. Opportunities and Challenges for Being a Carbon Black Great Power

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    1. The "Uth Five-year Plan" Lay- ing the Foundation for Carbon Black Great Power 1.1 Rapid growth of carbon black output and production capacity During the "llth Five-year Plan" Period, China carbon black output was increased by 1.1 times and realized doubling; and the production capacity of carbon black realized an average annu- al growth of 16.9%. In 2011, the carbon black output was 3.853 million tons, increased by 14.2% compared with that of the last year, and the pro- portion of carbon black output in the world carbon black output was increased from 16% to 36%. The carbon black production capacity was 5.345 mil- lion tons, increased by 6% compared with that of the last year, and the proportion of carbon black production capacity in the world carbon black out- put reached 38%. Chinese carbon black output has been ranking the 1st place throughout the world for 6 years successively, and China has become a great power of carbon black production in the world.

  10. A black carbon air quality network

    Science.gov (United States)

    Kirchstetter, T.; Caubel, J.; Cados, T.; Preble, C.; Rosen, A.

    2016-12-01

    We developed a portable, power efficient black carbon sensor for deployment in an air quality network in West Oakland, California. West Oakland is a San Francisco Bay Area residential/industrial community adjacent to regional port and rail yard facilities, and is surrounded by major freeways. As such, the community is affected by diesel particulate matter emissions from heavy-duty diesel trucks, locomotives, and ships associated with freight movement. In partnership with Environmental Defense Fund, the Bay Area Air Quality Management District, and the West Oakland Environmental Indicators Project, we are collaborating with community members to build and operate a 100-sensor black carbon measurement network for a period of several months. The sensor employs the filter-based light transmission method to measure black carbon. Each sensor node in the network transmits data hourly via SMS text messages. Cost, power consumption, and performance are considered in choosing components (e.g., pump) and operating conditions (e.g., sample flow rate). In field evaluation trials over several weeks at three monitoring locations, the sensor nodes provided black carbon concentrations comparable to commercial instruments and ran autonomously for a week before sample filters and rechargeable batteries needed to be replaced. Buildup to the 100-sensor network is taking place during Fall 2016 and will overlap with other ongoing air monitoring projects and monitoring platforms in West Oakland. Sensors will be placed along commercial corridors, adjacent to freeways, upwind of and within the Port, and throughout the residential community. Spatial and temporal black carbon concentration patterns will help characterize pollution sources and demonstrate the value of sensing networks for characterizing intra-urban air pollution concentrations and exposure to air pollution.

  11. Cycling of black carbon in the ocean

    OpenAIRE

    2016-01-01

    Black carbon (BC) is a byproduct of combustion from wildfires and fossil fuels and is a slow-cycling component of the carbon cycle. Whether BC accumulates and ages on millennial timescales in the world oceans has remained unknown. Here, we quantified dissolved BC (DBC) in marine dissolved organic carbon (DOC) isolated by solid phase extraction (SPE) at several sites in the world ocean. We find that DBC in the Atlantic, Pacific and Arctic oceans ranges from 1.4 to 2.6 μM in the surface and is ...

  12. Cycling of black carbon in the ocean

    OpenAIRE

    Coppola, Alysha I; Druffel, Ellen R. M.

    2016-01-01

    Black carbon (BC) is a byproduct of combustion from wildfires and fossil fuels and is a slow-cycling component of the carbon cycle. Whether BC accumulates and ages on millennial timescales in the world oceans has remained unknown. Here, we quantified dissolved BC (DBC) in marine dissolved organic carbon (DOC) isolated by solid phase extraction (SPE) at several sites in the world ocean. We find that DBC in the Atlantic, Pacific and Arctic oceans ranges from 1.4 to 2.6 μM in the surface and is ...

  13. Using measurements for evaluation of black carbon modeling

    Directory of Open Access Journals (Sweden)

    S. Gilardoni

    2010-04-01

    Full Text Available The ever increasing use of air quality and climate model assessments to underpin economic, public health, and environmental policy decisions makes effective model evaluation critical. This paper discusses the properties of black carbon and light attenuation and absorption observations that are the key to a reliable evaluation of black carbon model and compares parametric and nonparametric statistical tools for the quantification of the agreement between models and observations. Black carbon concentrations are simulated with TM5/M7 global model from July 2002 to June 2003 at four remote sites (Alert, Jungfraujoch, Mace Head, and Trinidad Head and two regional background sites (Bondville and Ispra. Equivalent black carbon (EBC concentrations are calculated using light attenuation measurements from January 2000 to December 2005. Seasonal trends in the measurements are determined by fitting sinusoidal functions and the representativeness of the period simulated by the model is verified based on the scatter of the experimental values relative to the fit curves. When the resolution of the model grid is larger than 1°×1°, it is recommended to verify that the measurement site is representative of the grid cell. For this purpose, equivalent black carbon measurements at Alert, Bondville and Trinidad Head are compared to light absorption and elemental carbon measurements performed at different sites inside the same model grid cells. Comparison of these equivalent black carbon and elemental carbon measurements indicates that uncertainties in black carbon optical properties can compromise the comparison between model and observations. During model evaluation it is important to examine the extent to which a model is able to simulate the variability in the observations over different integration periods as this will help to identify the most appropriate timescales. The agreement between model and observation is accurately described by the overlap of

  14. Using measurements for evaluation of black carbon modeling

    Directory of Open Access Journals (Sweden)

    S. Gilardoni

    2011-01-01

    Full Text Available The ever increasing use of air quality and climate model assessments to underpin economic, public health, and environmental policy decisions makes effective model evaluation critical. This paper discusses the properties of black carbon and light attenuation and absorption observations that are the key to a reliable evaluation of black carbon model and compares parametric and nonparametric statistical tools for the quantification of the agreement between models and observations. Black carbon concentrations are simulated with TM5/M7 global model from July 2002 to June 2003 at four remote sites (Alert, Jungfraujoch, Mace Head, and Trinidad Head and two regional background sites (Bondville and Ispra. Equivalent black carbon (EBC concentrations are calculated using light attenuation measurements from January 2000 to December 2005. Seasonal trends in the measurements are determined by fitting sinusoidal functions and the representativeness of the period simulated by the model is verified based on the scatter of the experimental values relative to the fit curves. When the resolution of the model grid is larger than 1° × 1°, it is recommended to verify that the measurement site is representative of the grid cell. For this purpose, equivalent black carbon measurements at Alert, Bondville and Trinidad Head are compared to light absorption and elemental carbon measurements performed at different sites inside the same model grid cells. Comparison of these equivalent black carbon and elemental carbon measurements indicates that uncertainties in black carbon optical properties can compromise the comparison between model and observations. During model evaluation it is important to examine the extent to which a model is able to simulate the variability in the observations over different integration periods as this will help to identify the most appropriate timescales. The agreement between model and observation is accurately described by the overlap of

  15. Study on Microwave Dielectric Property of Carbon Black and Short Carbon Fibers

    Institute of Scientific and Technical Information of China (English)

    WU Hong-huan; ZHU Dong-mei; LUO Fa; ZHOU Wan-cheng; WANG Xiao-yan

    2006-01-01

    Carbon black and carbon fibers of different lengths were introduced in different matrices at different ratios to explore their microwave dielectric properties under 8.2 GHz-12.4 GHz. It is found that the actual dielectric constants of the samples containing carbon black are in a two-order function of the contents of carbon black ((з)′,(з)″=Av2+Bv+C) and the complex dielectric constants show an obvious frequency response. Of the added fibers of different lengths, the 4 mm-long one could well disperse in the matrices having not only good frequency response, but also larger real parts, imaginary parts and loss values. The imaginary parts and the loss values (tanδ) of the samples with 4 mm-long carbon fibers added increase linearly with the contents of fiber increasing. So it is practicable to adjust the dielectric parameters of the material in a wide range by changing the added amount of carbon black, and the carbon fiber or altering the lengths of the carbon fiber added.

  16. [Effects of long-term fertilization on organic carbon functional groups in black soil as revealed by synchrotron radiation soft X-ray near-edge absorption spectroscopy].

    Science.gov (United States)

    Wang, Nan; Wang, Shuai; Wang, Qing-He; Dong, Pei-Bo; Li, Cui-Lan; Zhang, Jin-Jing; Gao, Qiang; Zhao, Yi-Dong

    2012-10-01

    A 20 years (1984-2004) stationary field experiment was conducted to evaluate the effects of long-term application of chemical fertilizers (N or NPK) alone or in combination with low (0.125 kg x hm(-2)) or high dose of corn stalk (0.25 kg x hm(-2)) on organic carbon functional groups in black soil using synchrotron radiation soft X-ray near-edge absorption spectroscopy (C-1s NEXAFS). Compared with the control (CK) treatment, the aromatic C and the carboxyl C of soil increased, whereas the aliphatic C, the carbonyl C and the aliphatic C/aromatic C ratio decreased after the application of chemical fertilizer alone. After the application of chemical fertilizations in combined with corn stalk, the aromatic C decreased while the aliphatic C and the aliphatic C/aromatic C ratio increased as compared to N or NPK fertilizer treatment. And the change tendency was more obvious with the increase in the dose of corn stalk applied. Regardless of corn stalk application, the aromatic C, the aliphatic C, and the aliphatic C/aromatic C ratio were all higher for NPK than for N fertilizer treatment. The above results indicated that, compared with the no-fertilizer control treatment, the application of chemical fertilizers alone resulted in the relative proportion of aromatic compounds increased whereas that of aliphatic hydrocarbon compounds decreased. On the other hand, the relative proportion of the aliphatic hydrocarbon compounds was higher after the application of chemical fertilizers with than without corn stalk, with high than with low dose of corn stalk, and with NPK than with N fertilization. C-1s NEXAFS spectroscopy could characterize in situ the changes of organic carbon functional groups in soil under long-term stationary fertilization.

  17. Black carbon measurements using an integrating sphere

    Science.gov (United States)

    Hitzenberger, R.; Dusek, U.; Berner, A.

    1996-08-01

    An integrating sphere was used to determine the black carbon (BC) content of aerosol filter samples dissolved in chloroform (method originally described by Heintzenberg [1982]). The specific absorption coefficient Ba (equal to absorption per mass) of the samples was also measured using the sphere as an integrating detector for transmitted light. Comparing the Ba of ambient samples taken in Vienna, Austria, to the BC concentrations measured on the dissolved filters, a value of approximately 6 m2/g was found to be a reasonable value for the Ba of the black carbon found at the site. The size dependence of Ba of a nebulized suspension of soot was measured using a rotating impactor, and a reasonable agreement between measured and calculated values was found.

  18. Black Carbon Contribution to Organic Carbon Stocks in Urban Soil

    DEFF Research Database (Denmark)

    Edmondson, Jill L.; Stott, Iain; Potter, Jonathan;

    2015-01-01

    Soil holds 75% of the total organic carbon (TOC) stock in terrestrial ecosystems. This comprises ecosystem-derived organic carbon (OC) and black carbon (BC), a recalcitrant product of the incomplete combustion of fossil fuels and biomass. Urban topsoils are often enriched in BC from historical...... increased with soil depth, and was enriched in topsoil under trees when compared to grassland. Our findings establish the importance of urban ecosystems in storing large amounts of OC in soils and that these soils also capture a large proportion of BC particulates emitted within urban areas....

  19. Pulmonary exposure to carbon black nanoparticles and vascular effects

    Directory of Open Access Journals (Sweden)

    Wallin Håkan

    2010-11-01

    Full Text Available Abstract Background Exposure to small size particulates is regarded as a risk factor for cardiovascular diseases. Methods We exposed young and aged apolipoprotein E knockout mice (apoE-/- to carbon black (Printex 90, 14 nm by intratracheal instillation, with different dosing and timing, and measured vasomotor function, progression of atherosclerotic plaques, and VCAM-1, ICAM-1, and 3-nitrotyrosine in blood vessels. The mRNA expression of VCAM-1, ICAM-1, HO-1, and MCP-1 was examined in lung tissue. Results Young apoE-/- mice exposed to two consecutive 0.5 mg/kg doses of carbon black exhibited lower acetylcholine-induced vasorelaxation in aorta segments mounted in myographs, whereas single doses of 0.05-2.7 mg/kg produced no such effects. The phenylephrine-dependent vasocontraction response was shifted toward a lower responsiveness in the mice exposed once to a low dose for 24 hours. No effects were seen on the progression of atherosclerotic plaques in the aged apoE-/- mice or on the expression of VCAM-1 and ICAM-1 and the presence of 3-nitrotyrosine in the vascular tissue of either young or aged apoE-/- mice. The expression of MCP-1 mRNA was increased in the lungs of young apoE-/- mice exposed to 0.9-2.7 mg/kg carbon black for 24 hours and of aged apoE-/- mice exposed to two consecutive 0.5 mg/kg doses of carbon black seven and five weeks prior to sacrifice. Conclusion Exposure to nano-sized carbon black particles is associated with modest vasomotor impairment, which is associated neither with nitrosative stress nor with any obvious increases in the expression of cell adhesion proteins on endothelial cells or in plaque progression. Evidence of pulmonary inflammation was observed, but only in animals exposed to higher doses.

  20. Black carbon network in Mexico. First Results

    Science.gov (United States)

    Barrera, Valter; Peralta, Oscar; Granado, Karen; Ortinez, Abraham; Alvarez-Ospina, Harry; Espinoza, Maria de la Luz; Castro, Telma

    2017-04-01

    After the United Nations Framework Convention on Climate Change celebrated in Paris 2016, many countries should adopt some mechanisms in the next years to contribute to mitigate greenhouse gas emissions and support sustainable development. Mexico Government has adopted an unconditional international commitment to carry out mitigation actions that would result in the reduction of 51% in black carbon (BC) emissions by year 2030. However, many BC emissions have been calculated by factor emissions. Since optical measurements of environmental BC concentrations can vary according the different components and their subsequence wavelength measure, it's important to obtain more accurate values. BC is formally defined as an ideally light-absorbing substance composed by carbon (Bond et al., 2013), and is the second main contributor (behind Carbon Dioxide; CO2) to positive radiative forcing (Ramanathan and Carmichael, 2008). Recently, BC has been used as an additional indicator in air quality management in some cities because is emitted from the incomplete combustion of fossil fuels, biofuel and biomass burning in both anthropogenic and it is always emitted with other particles and gases, such as organic carbon (OC), nitrogen oxides (NOx), and sulfur dioxide (SO2). Black Carbon, PM2.5 and pollutant gases were measured from January 2015 to December 2015 at three main cities in Mexico, and two other places to evaluate the BC concentration levels in the country. The urban background sites (Mexico City, Monterrey, Guadalajara, MXC-UB, GDL-UB, MTY-UB), a sub-urban background site (Juriquilla, Queretaro, JUR-SUB) and a regional background site (Altzomoni, ALT-RB). Results showed the relationship between BC and PM2.5 in the 3 large cities, with BC/PM2.5 ratios near 0.14 to 0.09 and a high BC-CO relationship in all the year in Mexico City, who showed that mobile sources are a common, at least in cities with a non-significant biomass burning emission related to agriculture or coal

  1. Black Carbon Measurement and Modeling in the Arabian Peninsula

    Science.gov (United States)

    Zawad, Faisal Al; Khoder, Mamdouh; Almazroui, Mansour; Alghamdi, Mansour; Lihavainen, Heikki; Hyvarinen, Antti; Henriksson, Svante

    2017-04-01

    Black carbon is an important atmospheric aerosol as an effective factor in public health, changing the global and regional climate, and reducing visibility. Black carbon absorbs light, warms the atmosphere, and modifies cloud droplets and the amount of precipitation. In spite of this significance, knowledge of black carbon over the Arabian Peninsula is hard to find in literature until recently. The total mass of black carbon and wind direction and speeds were measured continuously at Hada Al-Sham, Saudi Arabia for the year 2013. In addition, a state of the art global aerosol - climate model (ECHAM5-HAM) was used to determine black carbon climatology over the Arabian Peninsula. Simulation of the model was carried out for the years eight years (2004 - 2011). The daily mean values of the concentrations of black carbon had a minimum of 15.0 ng/m3 and a maximum of 6372 ng/m3 with a mean of at 1899 ng/m3. The diurnal pattern of black carbon showed higher values overnight, and steady low values during daytimes caused by sea and land breezes. Seasons of black carbon vary over the Arabian Peninsula, and the longest is in the Northern Region where it lasts from July to October. High concentrations of black carbon at Hada Al-Sham was observed with a mean of 1.9 µm/m3, and seasons of black carbon vary widely across the Arabian Peninsula. Assessment of the effects of black carbon over the Arabian Peninsula on the global radiation balance. Initiating a black carbon monitoring network is highly recommended to assess its impacts on health, environment, and climate.

  2. CCN activation of pure and coated carbon black particles.

    Science.gov (United States)

    Dusek, U; Reischl, G P; Hitzenberger, R

    2006-02-15

    The CCN (cloud condensation nucleus) activation of pure and coated carbon black particles was investigated using the University of Vienna cloud condensation nuclei counter (Giebl, H.; Berner, A.; Reischl, G.; Puxbaum, H.; Kasper-Giebl, A.; Hitzenberger, R. J. Aerosol Sci. 2002, 33, 1623-1634). The particles were produced by nebulizing an aqueous suspension of carbon black in a Collison atomizer. The activation of pure carbon black particles was found to require higher supersaturations than predicted by calculations representing the particles as insoluble, wettable spheres with mobility equivalent diameter. To test whether this effect is an artifact due to heating of the light-absorbing carbon black particles in the laser beam, experiments at different laser powers were conducted. No systematic dependence of the activation of pure carbon black particles on laser power was observed. The observations could be modeled using spherical particles and an effective contact angle of 4-6 degrees of water at their surface. The addition of a small amount of NaCl to the carbon black particles (by adding 5% by mass NaCl to the carbon black suspension) greatly enhanced their CCN efficiency. The measured CCN efficiencies were consistent with Kohler theory for particles consisting of insoluble and hygroscopic material. However, coating the carbon black particles with hexadecanol (a typical film-forming compound with one hydrophobic and one hydrophilic end) efficiently suppressed the CCN activation of the carbon black particles.

  3. Prenatal Exposure to Carbon Black (Printex 90)

    DEFF Research Database (Denmark)

    Jackson, Petra; Vogel, Ulla; Wallin, Håkan;

    2011-01-01

    Maternal pulmonary exposure to ultrafine particles during pregnancy may affect the health of the child. Developmental toxicity of carbon black (Printex 90) nanoparticles was evaluated in a mouse model. Time-mated mice were intratracheally instilled with Printex 90 dispersed in Millipore water on ...... on gestation days (GD) 7, 10, 15 and 18, with total doses of 11, 54 and 268 mu g Printex 90/animal. The female offspring prenatally exposed to 268 mu g Printex 90/animal displayed altered habituation pattern during the Open field test....

  4. Partition functions for supersymmetric black holes

    NARCIS (Netherlands)

    Manschot, J.

    2008-01-01

    This thesis presents a number of results on partition functions for four-dimensional supersymmetric black holes. These partition functions are important tools to explain the entropy of black holes from a microscopic point of view. Such a microscopic explanation was desired after the association of a

  5. Supply Deficit of Feedstock Oils for Carbon Black

    Institute of Scientific and Technical Information of China (English)

    Li Bingyan

    2007-01-01

    @@ Feedstock oils used for carbon blackproduction mainly include ethylene tar,anthracene oil and coal tar. With thegrowing output of carbon black in re-cent years, demand for feedstock oilshas increased constantly.

  6. Feasibility study of production of radioactive carbon black or carbon nanotubes in cyclotron facilities for nanobioscience applications.

    Science.gov (United States)

    Abbas, K; Simonelli, F; Holzwarth, U; Cydzik, I; Bulgheroni, A; Gibson, N; Kozempel, J

    2013-03-01

    A feasibility study regarding the production of radioactive carbon black and nanotubes has been performed by proton beam irradiation. Experimental and theoretical excitation functions of the nuclear reaction (nat)C(p,x)(7)Be in the proton energy range 24-38 MeV are reported, with an acceptable agreement. We have demonstrated that sufficient activities of (7)Be radioisotope can be produced in carbon black and nanotube that would facilitate studies of their possible impact on human and environment.

  7. Grafted, cross-linked carbon black as a double-layer capacitor electrode material

    Energy Technology Data Exchange (ETDEWEB)

    Richner, R.; Mueller, S.; Wokaun, A.

    2001-03-01

    Isocyanate prepolymers readily react with oxidic functional groups on carbon black. On carbon black grafted with diisocyanates, reactive isocyanate groups are available for cross-linking to a polyurethane system. This cross-linked carbon black was considered as a new active material for electrochemical electrodes. Active material for electric double-layer capacitor electrodes was produced which had values of specific capacitance of up to 200 F/g. Cross-linking efficiencies of up to 58 % of the polymers utilised were achieved. (author)

  8. Effect of sterilization on mineralization of straw and black carbon

    DEFF Research Database (Denmark)

    Bobul'ská, Lenka; Bruun, Sander; Fazekašová, Danica

    2013-01-01

    The study was aimed at investigating the role of microorganisms in the degradation of BC (black carbon). CO evolution was measured under sterilized and non-sterilized soil using BC and straw amendments. Black carbon and straw were produced from homogenously C labelled roots of barley (Hordeum vul...... abiotic source must also be present perhaps abiotic mineralization of labile BC components....

  9. Thermal properties of carbon black aqueous nanofluids for solar absorption

    Directory of Open Access Journals (Sweden)

    Han Dongxiao

    2011-01-01

    Full Text Available Abstract In this article, carbon black nanofluids were prepared by dispersing the pretreated carbon black powder into distilled water. The size and morphology of the nanoparticles were explored. The photothermal properties, optical properties, rheological behaviors, and thermal conductivities of the nanofluids were also investigated. The results showed that the nanofluids of high-volume fraction had better photothermal properties. Both carbon black powder and nanofluids had good absorption in the whole wavelength ranging from 200 to 2,500 nm. The nanofluids exhibited a shear thinning behavior. The shear viscosity increased with the increasing volume fraction and decreased with the increasing temperature at the same shear rate. The thermal conductivity of carbon black nanofluids increased with the increase of volume fraction and temperature. Carbon black nanofluids had good absorption ability of solar energy and can effectively enhance the solar absorption efficiency.

  10. Thermal properties of carbon black aqueous nanofluids for solar absorption.

    Science.gov (United States)

    Han, Dongxiao; Meng, Zhaoguo; Wu, Daxiong; Zhang, Canying; Zhu, Haitao

    2011-07-18

    In this article, carbon black nanofluids were prepared by dispersing the pretreated carbon black powder into distilled water. The size and morphology of the nanoparticles were explored. The photothermal properties, optical properties, rheological behaviors, and thermal conductivities of the nanofluids were also investigated. The results showed that the nanofluids of high-volume fraction had better photothermal properties. Both carbon black powder and nanofluids had good absorption in the whole wavelength ranging from 200 to 2,500 nm. The nanofluids exhibited a shear thinning behavior. The shear viscosity increased with the increasing volume fraction and decreased with the increasing temperature at the same shear rate. The thermal conductivity of carbon black nanofluids increased with the increase of volume fraction and temperature. Carbon black nanofluids had good absorption ability of solar energy and can effectively enhance the solar absorption efficiency.

  11. Thermal properties of carbon black aqueous nanofluids for solar absorption

    Science.gov (United States)

    Han, Dongxiao; Meng, Zhaoguo; Wu, Daxiong; Zhang, Canying; Zhu, Haitao

    2011-07-01

    In this article, carbon black nanofluids were prepared by dispersing the pretreated carbon black powder into distilled water. The size and morphology of the nanoparticles were explored. The photothermal properties, optical properties, rheological behaviors, and thermal conductivities of the nanofluids were also investigated. The results showed that the nanofluids of high-volume fraction had better photothermal properties. Both carbon black powder and nanofluids had good absorption in the whole wavelength ranging from 200 to 2,500 nm. The nanofluids exhibited a shear thinning behavior. The shear viscosity increased with the increasing volume fraction and decreased with the increasing temperature at the same shear rate. The thermal conductivity of carbon black nanofluids increased with the increase of volume fraction and temperature. Carbon black nanofluids had good absorption ability of solar energy and can effectively enhance the solar absorption efficiency.

  12. Cycling of black carbon in the ocean

    Science.gov (United States)

    Coppola, Alysha I.; Druffel, Ellen R. M.

    2016-05-01

    Black carbon (BC) is a by-product of combustion from wildfires and fossil fuels and is a slow-cycling component of the carbon cycle. Whether BC accumulates and ages on millennial time scales in the world oceans has remained unknown. Here we quantified dissolved BC (DBC) in marine dissolved organic carbon isolated by solid phase extraction at several sites in the world ocean. We find that DBC in the Atlantic, Pacific, and Arctic oceans ranges from 1.4 to 2.6 μM in the surface and is 1.2 ± 0.1 μM in the deep Atlantic. The average 14C age of surface DBC is 4800 ± 620 14C years and much older in a deep water sample (23,000 ± 3000 14C years). The range of DBC structures and 14C ages indicates that DBC is not homogeneous in the ocean. We show that there are at least two distinct pools of marine DBC, a younger pool that cycles on centennial time scales and an ancient pool that cycles on >105 year time scales.

  13. Estimation and prediction of black carbon emissions in Beijing City

    Institute of Scientific and Technical Information of China (English)

    LIU Yuan; SHAO Min

    2007-01-01

    Black carbon is a by-product of incomplete combustion of carbon containing fuels. It can alter atmospheric radiation property and make adverse impacts on human health. The energy consumption in Beijing City depends largely on coal burning. Recently, Beijing City has been performing the municipal energy structure adjustment as a tool for air pollution abatement, aiming at the air quality goal for the Beijing 2008 Olympic Games. Based on Beijing energy use data in 2000, combined with emission factors of major sources of black carbon, the emission of black carbon in Beijing City is estimated to be 7.77 Gg. Coke, raw coal and biomass as non-commercial energy are the main contributors to municipal black carbon emissions. Based on Beijing energy planning in the year 2008, the emission of black carbon in 2008 will be 2.97 Gg if the contribution from biomass is not taken into account. Assuming that the black carbon emission from rural biomass in 2008 is the same as that in 2004, the biomass burning will be the largest emitter of black carbon to Beijing City in 2008.

  14. Preparation and application of active gangue's carbon black

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xiang-lin; ZHANG Yi-dong

    2007-01-01

    After three-stage pulverization, dry-distillated activation and coupling agent surface modification, the kaolinite-typed gangue of Sichuan Hongni Coal Mine(SHCM) can be manufactured into activated gangue's carbon black. Its surface area is >25 m2/g, and possesses carbon black's carbon framework and structure. It can be used as strengthening agent of high polymer material such as rubber.

  15. Addressing inconsistencies in black carbon literature

    Science.gov (United States)

    Shonkoff, S. B.; Chafe, Z.; Smith, K. R.

    2010-12-01

    The literature describing black carbon (BC) emissions, and their effect on Earth’s climate, is growing rapidly. Unfortunately, inconsistencies in definitions; data collection and characterization; system boundaries; and time horizons have led to confusion about the relative importance of BC compared to other climate-active pollutant (CAPs). We discuss three sources of confusion: 1) Currently available BC inventories are not directly comparable to those used by the IPCC to track the greenhouse gases (GHGs) considered in the Kyoto Protocol (CO2, CH4, N2O). In particular, BC inventories often include all emissions: natural and anthropogenic in origin, controllable and non-controllable. IPCC inventories include only anthropogenic emissions. This BC accounting is appropriate for atmospheric science deliberations, but risks being interpreted as an overstatement against official Kyoto GHG inventories in a policy or control context. The IPCC convention of using 1750 as the starting year for emission inventories further complicates matters: significant BC emissions were emitted previous to that date by both human and natural sources. Though none of the pre-1750 BC emissions remain in the atmosphere today, their legacy presents challenges in assigning historical responsibility for associated global warming among sectors and regional populations. 2) Inconsistencies exist in the specific emissions sources considered in atmospheric models used to predict net BC forcing often lead to widely varying climate forcing estimates. For example, while some analyses consider only fossil fuel 1, others include both open biomass burning and fossil fuel combustion 2, and yet others include sources beyond biomass and fossil fuel burning 3. 3) Inconsistencies exist in how analyses incorporate the relationship between BC emissions and the associated cooling aerosols and processes, such as organic carbon (OC), and aerosol indirect effects (AIE). Unlike Kyoto GHGs, BC is rarely emitted in pure

  16. Simplifying the calculation of light scattering properties for black carbon fractal aggregates

    Science.gov (United States)

    Smith, A. J. A.; Grainger, R. G.

    2014-02-01

    Black carbon fractal aggregates have complicated shapes that make the calculation of their optical properties particularly computationally expensive. Here, a method is presented to estimate fractal aggregate light scattering properties by optimising simplified models to full light scattering calculations. It is found that there are no possible spherical models (at any size or refractive index) that well represent the light scattering in the visible, or near-thermal infrared. As such, parameterisations of the light scattering as a function of the number of aggregate particles is presented as the most pragmatic choice for modelling distributions of black carbon when the large computational overheads of rigorous scattering calculations cannot be justified. This parameterisation can be analytically integrated to provide light scattering properties for log-normal distributions of black carbon fractal aggregates and return extinction cross-sections with 0.1% accuracy for typical black carbon size distributions. Scattering cross-sections and the asymmetry parameter can be obtained to within 3%.

  17. Simplifying the calculation of light scattering properties for black carbon fractal aggregates

    Directory of Open Access Journals (Sweden)

    A. J. A. Smith

    2014-08-01

    Full Text Available Black carbon fractal aggregates have complicated shapes that make the calculation of their optical properties particularly computationally expensive. Here, a method is presented to estimate fractal aggregate light scattering properties by optimising simplified models to full light scattering calculations. It is found that there are no possible spherical models (at any size or refractive index that well represent the light scattering in the visible or near-thermal infrared. As such, parameterisations of the light scattering as a function of the number of aggregate particles is presented as the most pragmatic choice for modelling distributions of black carbon when the large computational overheads of rigorous scattering calculations cannot be justified. This parameterisation can be analytically integrated to provide light scattering properties for lognormal distributions of black carbon fractal aggregates and return extinction cross sections with 0.1% accuracy for typical black carbon size distributions. Scattering cross sections and the asymmetry parameter can be obtained to within 3%.

  18. Black Carbon Contribution to Organic Carbon Stocks in Urban Soil.

    Science.gov (United States)

    Edmondson, Jill L; Stott, Iain; Potter, Jonathan; Lopez-Capel, Elisa; Manning, David A C; Gaston, Kevin J; Leake, Jonathan R

    2015-07-21

    Soil holds 75% of the total organic carbon (TOC) stock in terrestrial ecosystems. This comprises ecosystem-derived organic carbon (OC) and black carbon (BC), a recalcitrant product of the incomplete combustion of fossil fuels and biomass. Urban topsoils are often enriched in BC from historical emissions of soot and have high TOC concentrations, but the contribution of BC to TOC throughout the urban soil profile, at a regional scale is unknown. We sampled 55 urban soil profiles across the North East of England, a region with a history of coal burning and heavy industry. Through combined elemental and thermogravimetic analyses, we found very large total soil OC stocks (31-65 kg m(-2) to 1 m), exceeding typical values reported for UK woodland soils. BC contributed 28-39% of the TOC stocks, up to 23 kg C m(-2) to 1 m, and was affected by soil texture. The proportional contribution of the BC-rich fraction to TOC increased with soil depth, and was enriched in topsoil under trees when compared to grassland. Our findings establish the importance of urban ecosystems in storing large amounts of OC in soils and that these soils also capture a large proportion of BC particulates emitted within urban areas.

  19. Source attribution of black carbon in Arctic snow.

    Science.gov (United States)

    Hegg, Dean A; Warren, Stephen G; Grenfell, Thomas C; Doherty, Sarah J; Larson, Timothy V; Clarke, Antony D

    2009-06-01

    Snow samples obtained at 36 sites in Alaska, Canada, Greenland, Russia, and the Arctic Ocean in early 2007 were analyzed for light-absorbing aerosol concentration together with a suite of associated chemical species. The light absorption data, interpreted as black carbon concentrations, and other chemical data were input into the EPA PMF 1.1 receptor model to explore the sources for black carbon in the snow. The analysis found four factors or sources: two distinct biomass burning sources, a pollution source, and a marine source. The first three of these were responsible for essentially all of the black carbon, with the two biomass sources (encompassing both open and closed combustion) together accounting for >90% of the black carbon.

  20. The uptake of ethyl iodide on black carbon surface

    Institute of Scientific and Technical Information of China (English)

    YIN Shi; WANG WeiGang; GE MaoFa

    2008-01-01

    The importance of the iodine chemistry in the atmosphere has been demonstrated by recent observations. The uptake of ethyl iodine on black carbon surface was investigated at 298 K for the first time. Degussa FW2 (an amorphous black carbon comprising medium oxides) was used as black carbon sample. Black carbon surface was found to be deactivated in reaction with C2H5I, and the uptake coefficient (γ) was dependent on the time of exposure. The value of (2.3±0.9)×10-2 was determined for the initial uptake coefficient (γ0). The result suggests that the heterogeneous loss of C2H5I on carbonaceous aerosols may be important under the atmospheric conditions.

  1. Global civil aviation black carbon emissions.

    Science.gov (United States)

    Stettler, Marc E J; Boies, Adam M; Petzold, Andreas; Barrett, Steven R H

    2013-09-17

    Aircraft black carbon (BC) emissions contribute to climate forcing, but few estimates of BC emitted by aircraft at cruise exist. For the majority of aircraft engines the only BC-related measurement available is smoke number (SN)-a filter based optical method designed to measure near-ground plume visibility, not mass. While the first order approximation (FOA3) technique has been developed to estimate BC mass emissions normalized by fuel burn [EI(BC)] from SN, it is shown that it underestimates EI(BC) by >90% in 35% of directly measured cases (R(2) = -0.10). As there are no plans to measure BC emissions from all existing certified engines-which will be in service for several decades-it is necessary to estimate EI(BC) for existing aircraft on the ground and at cruise. An alternative method, called FOX, that is independent of the SN is developed to estimate BC emissions. Estimates of EI(BC) at ground level are significantly improved (R(2) = 0.68), whereas estimates at cruise are within 30% of measurements. Implementing this approach for global civil aviation estimated aircraft BC emissions are revised upward by a factor of ~3. Direct radiative forcing (RF) due to aviation BC emissions is estimated to be ~9.5 mW/m(2), equivalent to ~1/3 of the current RF due to aviation CO2 emissions.

  2. The Effectiveness of the Regulatory Regime for Black Carbon Mitigation in the Arctic

    Directory of Open Access Journals (Sweden)

    Daria Shapovalova

    2016-11-01

    Full Text Available In addition to being a hazardous air pollutant, Black Carbon is the second-largest contributor to Arctic warming. Its mitigation is being addressed at the international regulatory level by the Arctic Council and the Convention on Long-Range Transboundary Air Pollution (CLRTAP. Whilst the Convention and its protocols are binding documents, the Black Carbon regulation under their framework appears to have ‘soft law’ characteristics. At the same time, the voluntary Black Carbon and Methane Framework, adopted by the Arctic Council, demonstrates positive compliance and follow-up dynamics compared to earlier norm-creating attempts. This paper argues that the nature of the norm (binding or non-binding is not the decisive factor regarding effective implementation in the Arctic region. Current efforts to mitigate Black Carbon by means of a non-binding Arctic Council Black Carbon and Methane Framework represent an improvement in the Council's normative function and may have more effect on the behaviour of Arctic States than relevant provisions under the Gothenburg Protocol to the CLRTAP. To support this argument, the first section presents an overview of the Arctic Council as an actor in Arctic policy-making. It then provides an assessment of current efforts to combat Black Carbon carried out by the Arctic Council and the CLRTAP.

  3. Comparative DEMS study on the electrochemical oxidation of carbon blacks

    DEFF Research Database (Denmark)

    Ashton, Sean James; Arenz, Matthias

    2012-01-01

    heat-treated between 2100 and 3200 °C, such as those typically used as corrosion resistant carbon (CRC) supports for polymer electrolyte membrane fuel cell (PEMFC) catalysts. A methodology combining cyclic voltammetry (CV) and differential electrochemical mass spectrometry (DEMS) is used, which allows...... the characterisation and comparison of the complete electrochemical oxidation rates and behaviours of the various carbon blacks. It is observed that the behaviour of the carbon black towards electrochemical oxidation is highly dynamic, and dependent on the properties of the pristine carbon back, the degree...

  4. Effects of Surface-modification of Carbon Black on the Characteristics of Polymerized Toner

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Eun Ho; Kim, Dae Su [Chungbuk National University, Cheongju (Korea, Republic of)

    2013-10-15

    Carbon black was surface-modified to prepare styrene-based suspension polymerized toner with excellent carbon black dispersibility inside toner particles. Carbon black was oxidized first to introduce hydroxyl groups on the surfaces, then esterification between the hydroxyl groups and carboxyl groups of organic acids (oleic acid, palmitic acid, acrylic acid) was followed to obtain organically surface-modified carbon black. The surface-modification of carbon black was confirmed by FTIR. Apparent carbon black dispersibility in the monomer mixture of the binder resin was tested and the particle size of dispersed carbon black was measured by particle size analyzer. Optical micrographs showed that carbon black dispersibility inside toner particles was improved considerably when the carbon black surface-modified with oleic acid was used. The polymerized toner prepared with the carbon black surface-modified with oleic acid showed ideal particle size and size distribution as a toner.

  5. Black carbon radiative forcing at TOA decreased during aging

    Science.gov (United States)

    Wu, Yu; Cheng, Tianhai; Zheng, Lijuan; Chen, Hao

    2016-12-01

    During aging processing, black carbon (also called soot) particles may tend to be mixed with other aerosols, and highly influence their radiative forcing. In this study, freshly emitted soot particles were simulated as fractal aggregates composed of small spherical primary monomers. After aging in the atmosphere, soot monomers were coated by a thinly layer of sulfate as thinly coated soot particles. These soot particles were entirely embedded into large sulfate particle by further aging, and becoming heavily coated soot particles. In clear-sky conditions, black carbon radiative forcing with different aging states were investigated for the bottom and top of atmosphere (BOA and TOA). The simulations showed that black carbon radiative forcing increased at BOA and decreased at TOA after their aging processes. Thinly and heavily coated states increased up to ~12% and ~35% black carbon radiative forcing at BOA, and black carbon radiative forcing at TOA can reach to ~20% and ~100% smaller for thinly and heavily coated states than those of freshly emitted states, respectively. The effect of aging states of black carbon radiative forcing was varied with surface albedo, aerosol optical depth and solar zenith angles. These findings would be helpful for the assessments of climate change.

  6. Attractor black holes and quantum distribution functions

    Energy Technology Data Exchange (ETDEWEB)

    Montanez, S. [Instituto de Fisica Teorica CSIC-UAM, Modulo C-XVI, Facultad de Ciencias, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Gomez, C. [Instituto de Fisica Teorica CSIC-UAM, Modulo C-XVI, Facultad de Ciencias, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Theory Group, Physics Department, CERN, 1211 Geneva 23 (Switzerland)

    2007-05-15

    Using the attractor mechanism and the wavefunction interpretation of the topological string partition function on a Calabi Yau threefold M we study the relation between the Bekenstein-Hawking-Wald entropy of BPS Calabi-Yau black holes and quantum distribution functions defined on H{sup 3}(M). We discuss the OSV conjecture in this context. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  7. Synthesis of multiwalled carbon nanotube from different grades of carbon black using arc discharge method

    Energy Technology Data Exchange (ETDEWEB)

    Arora, Neha, E-mail: n4neha31@gmail.com [Department of Mechanical Engineering, Birla Institute of Technology and Science, Pilani (India); Sharma, N. N. [Department of Mechanical Engineering, Birla Institute of Technology and Science, Pilani (India); Director, School of Automobile, Mechanical & Mechatronics, Manipal University,Jaipur,India (India)

    2016-04-13

    This paper describes the synthesis of nanotube from different grades (Tread * A(non-ASTM), N134,N121,N660 and N330)of carbon black using DC arc discharge method at 40A current for 60sec. Carbon black samples of different grades were procured from industry (Aditya Birla Science and Technology Limited, India). Scanning Electron Micrographs (SEM) of the deposited carbon nanostructures suggests that MWCNTs are formed at 40A and for a minimal exposure time of 60sec.The result formed indicates the N330 grade of carbon black gets converted to MWCNTs (Multiwall Carbon nanotube) as compared to other grades.

  8. Adsorption of Remazol Black B dye on Activated Carbon Felt

    Directory of Open Access Journals (Sweden)

    Donnaperna Lucio

    2008-11-01

    Full Text Available The adsorption of Remazol Black B (anionic dye on a microporous activated carbon felt is investigated from its aqueous solution. The surface chemistry of activated carbon is studied using X-ray microanalysis, "Boehm" titrations and pH of PZC measurements which indicates that the surface oxygenated groups are mainly acidic in nature. The kinetics of Remazol Black B adsorption is observed to be pH dependent and governed by the diffusion of the dye molecules. The experimental data can be explained by "intra-particle diffusion model". For Remazol Black B, the Khan model is best suited to simulate the adsorption isotherms.

  9. Artificial black opal fabricated from nanoporous carbon spheres.

    Science.gov (United States)

    Yamada, Yuri; Ishii, Masahiko; Nakamura, Tadashi; Yano, Kazuhisa

    2010-06-15

    A nanocasting method via chemical vapor deposition of acetonitrile was successfully employed to fabricate porous carbon colloidal crystal using colloidal crystal from monodispersed mesoporous silica spheres (MMSS) as a sacrificial scaffold. The mesostructure as well as periodic arrays within (111) plane of MMSS were replicated for the carbon colloidal crystal (black opal) with the length scale in the centimeter range. Brilliant iridescent colors were clearly observed for the first time on the black carbon colloidal crystal fabricated from porous carbon spheres, and they changed dramatically in accordance with the observation angle, like natural black opals. Reflection spectra measurements based on 2D surface diffraction and Bragg diffraction in the mirror mode were conducted for the fabricated carbon periodic arrays. The periodicity in the (111) plane as well as in the direction perpendicular to the (111) plane of the colloidal crystal was evaluated by comparing the results obtained from these two measurements. It was found that the periodicity in the direction perpendicular to the (111) surface is not high for the obtained black carbon opal. On the other hand, the relationship between the incident angles and the peak wavelengths of the reflection spectra, collected in the condition where the incident light and the reflected light pass through in the same direction, is governed by an approximation based on 2D surface diffraction. The results imply that the origin of the iridescent colors on the fabricated black carbon opal is derived from the periodicity not in the direction perpendicular to the (111) plane but within the (111) plane.

  10. An Important Supplement to NAA in Study on Atmosphere Pollution:Determination of Black Carbon

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Light absorption in the atmosphere is dominated by elemental carbon (EC), sometimes called black carbon (BC). Black carbon is an important indication of man-made pollution in airborne particulate matter

  11. Advanced carbon nanotubes functionalization

    Science.gov (United States)

    Setaro, A.

    2017-10-01

    Similar to graphene, carbon nanotubes are materials made of pure carbon in its sp2 form. Their extended conjugated π-network provides them with remarkable quantum optoelectronic properties. Frustratingly, it also brings drawbacks. The π–π stacking interaction makes as-produced tubes bundle together, blurring all their quantum properties. Functionalization aims at modifying and protecting the tubes while hindering π–π stacking. Several functionalization strategies have been developed to circumvent this limitation in order for nanotubes applications to thrive. In this review, we summarize the different approaches established so far, emphasizing the balance between functionalization efficacy and the preservation of the tubes’ properties. Much attention will be given to a functionalization strategy overcoming the covalent–noncovalent dichotomy and to the implementation of two advanced functionalization schemes: (a) conjugation with molecular switches, to yield hybrid nanosystems with chemo-physical properties that can be tuned in a controlled and reversible way, and; (b) plasmonic nanosystems, whose ability to concentrate and enhance the electromagnetic fields can be taken advantage of to enhance the optical response of the tubes.

  12. Catalytic Enhancement of Carbon Black and Coal-Fueled Hybrid Direct Carbon Fuel Cells

    DEFF Research Database (Denmark)

    Deleebeeck, Lisa; Ippolito, Davide; Kammer Hansen, Kent

    2015-01-01

    Hybrid direct carbon fuel cells (HDCFCs) consisting of a solid carbon (carbon black)-molten carbonate ((62–38 wt% Li-K)2CO3) mixtures in the anode chamber of an anode-supported solid oxide fuel cell type full-cell are tested for their electrochemical performance between 700 and 800°C. Performance...

  13. Trade and the Future of China's Black Carbon Emissions

    Science.gov (United States)

    Persad, G.; Oppenheimer, M.; Naik, V.

    2016-12-01

    Emissions of black carbon aerosols in China have increased by over 200% during the last 50 years, with negative implications both for human health and for regional and global climate. The Representative Concentration Pathway (RCP) emissions scenarios all assume that China's future black carbon emissions will decrease. However, this decline partially depends on the assumption that the evolution of future pollutant emissions in developing nations will match the observed historical relationship between air quality and income in developed nations. Recent research has demonstrated that a substantial portion of China's current black carbon emissions are driven by the production of goods exported for consumption elsewhere. This constitutes an external demand for black carbon-emitting activity in China that is much smaller in the developed nations on which the historical air quality/income relationship is based. We here show using integrated assessment model output, general circulation modeling, and emissions and economic data that (1) China must achieve a faster technological and regulatory evolution than did developed countries in order achieve the same air quality/income trajectory; (2) China's uniquely large share of export-related black carbon-emitting activities and their potential growth are a plausible explanation for this disparity; and (3) the climate and health implications of these export-related black carbon emissions, if unmitigated, are of interest from a policy perspective. Together these results indicate that the production of goods for export will steepen the mitigation curve for China relative to developed nations, if China is to achieve the future black carbon emissions reductions assumed in the RCPs.

  14. Inkjet printing of carbon black electrodes for dielectric elastomer actuators

    Science.gov (United States)

    Schlatter, Samuel; Rosset, Samuel; Shea, Herbert

    2017-04-01

    Inkjet printing is an appealing technique to print electrodes for Dielectric Elastomer Actuators (DEAs). Here we present the preparation and ink-jet printing of a carbon black electrode mixture and characterise its properties. Carbon black has been used extensively in the past because it is very compliant; however, it has a high resistance and can be very dirty to work with. In this paper we show that carbon black remains an appropriate electrode material, and when inkjet printed can be used to fabricate devices meeting today's demanding requirements. DEAs are becoming thinner to decrease actuation voltages and are shrinking in size to match the scale of the devices in the biomedical field, tuneable optics, and microfluidics. Inkjet printing addresses both of these problems. Firstly, Inkjet printing is a non-contact technique and can print on very thin freestanding membranes. Secondly, the high precision of inkjet printers makes it possible to print complex electrode geometries in the millimetre scale. We demonstrate the advantages of inkjet printing and carbon black electrodes by conducting a full characterisation of the printed electrodes. The printed carbon black electrodes have resistances as low as 13kΩ/□, an elastic modulus of approximately 1MPa, and a cyclic resistance swing which increases by 7% over 1500 cycles at 50% stretch. We also demonstrate a DEA with printed carbon black electrodes with a diametral stretch of 8.8% at an electric field of approximately 94V/μm. Finally a qualitative test is conducted to show that the printed carbon black electrode is extremely hardwearing.

  15. Time Function and Absolute Black Hole

    DEFF Research Database (Denmark)

    Javadi, Hossein; Forouzbakhsh, Farshid

    2006-01-01

    Einstein’s theory of gravity is not consistent with quantum mechanics, because general relativity cannot be quantized. [1] But without conversion of force and energy, it is impossible to find a grand unified theory. A very important result of CPH theory is time function that allows we give a new ...... description of absolute black hole and before the big bang....

  16. MORPHOLOGY OF BLACK CARBON AEROSOLS AND UBIQUITY OF 50-NANOMETER BLACK CARBON AEROSOLS IN THE ATMOSPHERE

    Institute of Scientific and Technical Information of China (English)

    Fengfu Fu; Liangjun Xu; Wei Ye; Yiquan Chen; Mingyu Jiang; Xueqin Xu

    2006-01-01

    Different-sized aerosols were collected by an Andersen air sampler to observe the detailed morphology of the black carbon (BC) aerosols which were separated chemically from the other accompanying aerosols, using a Scanning Electron Microscope equipped with an Energy Dispersive X-ray Spectrometer (SEM-EDX). The results indicate that most BC aerosols are spherical particles of about 50 nm in diameter and with a homogeneous surface. Results also show that these particles aggregate with other aerosols or with themselves to form larger agglomerates in the micrometer range. The shape of these 50-nm BC spherical particles was found to be very similar to that of BC particles released from petroleum-powered vehicular internal combustion engines. These spherical BC particles were shown to be different from the previously reported fullerenes found using Matrix-Assisted Laser Desorption/Ionization Time-Of-Flight Mass Spectrometry (MALDI-TOF-MS).

  17. Functionalization of Carbon Nanotubes

    Science.gov (United States)

    Khare, Bishun N. (Inventor); Meyyappan, Meyya (Inventor)

    2009-01-01

    Method and system for functionalizing a collection of carbon nanotubes (CNTs). A selected precursor gas (e.g., H2 or F2 or CnHm) is irradiated to provide a cold plasma of selected target species particles, such as atomic H or F, in a first chamber. The target species particles are d irected toward an array of CNTs located in a second chamber while suppressing transport of ultraviolet radiation to the second chamber. A CNT array is functionalized with the target species particles, at or below room temperature, to a point of saturation, in an exposure time interval no longer than about 30 sec. *Discrimination against non-target species is provided by (i) use of a target species having a lifetime that is much greater than a lifetime of a non-target species and/or (2) use of an applied magnetic field to discriminate between charged particle trajectories for target species and for non-target species.

  18. Polymer-carbon black composite sensors in an electronic nose for air-quality monitoring

    Science.gov (United States)

    Ryan, M. A.; Shevade, A. V.; Zhou, H.; Homer, M. L.

    2004-01-01

    An electronic nose that uses an array of 32 polymer-carbon black composite sensors has been developed, trained, and tested. By selecting a variety of chemical functionalities in the polymers used to make sensors, it is possible to construct an array capable of identifying and quantifying a broad range of target compounds, such as alcohols and aromatics, and distinguishing isomers and enantiomers (mirror-image isomers). A model of the interaction between target molecules and the polymer-carbon black composite sensors is under development to aid in selecting the array members and to enable identification of compounds with responses not stored in the analysis library.

  19. Radiocarbon Studies of Black Carbon in the Marine Environment

    OpenAIRE

    2015-01-01

    The incomplete combustion of biomass and fossil fuels produces black carbon (BC). BC is recalcitrant and serves as a long term holding pool for carbon, with a mean residence time of one to two orders of magnitude greater than unburnt carbon on land. Yet the known sources of BC are far larger than the known sinks, which led to studies of BC in the ocean’s dissolved organic carbon (DOC) reservoir. The goal of this dissertation was to measure the abundance and residence times of BC in sedime...

  20. Costs and global impacts of black carbon abatement strategies

    OpenAIRE

    K. Rypdal; Rive, N.; T. K. Berntsen; Z. Klimont; Mideksa, T.K.; G. Myhre; R. B. Skeie

    2009-01-01

    Abatement of particulate matter has traditionally been driven by health concerns rather than its role in global warming. Here we assess future abatement strategies in terms of how much they reduce the climate impact of black carbon (BC) and organic carbon (OC) from contained combustion. We develop global scenarios which take into account regional differences in climate impact, costs of abatement and ability to pay, as well as both the direct and indirect (snow-albedo) climate impact of BC ...

  1. Evaluation of black carbon estimations in global aerosol models

    NARCIS (Netherlands)

    Koch, D.; Schulz, M.; McNaughton, C.; Spackman, J.R.; Balkanski, Y.; Bauer, S.; Krol, M.C.

    2009-01-01

    We evaluate black carbon (BC) model predictions from the AeroCom model intercomparison project by considering the diversity among year 2000 model simulations and comparing model predictions with available measurements. These model-measurement intercomparisons include BC surface and aircraft concentr

  2. Black silicon maskless templates for carbon nanotube forests

    DEFF Research Database (Denmark)

    Wierzbicki, Rafal; Schmidt, Michael Stenbæk; Boisen, Anja

    2013-01-01

    We present here a proof of concept for a novel fabrication method of vertically aligned carbon nanotube forests, utilizing black silicon nanograss (a forest of silicon nanometer-sized spikes created with reactive ion etching) coated with titanium tungsten diffusion barrier as a template. The meth...

  3. Potential impacts of black carbon on the marine microbial community

    NARCIS (Netherlands)

    Malits, A.; Cattaneo, R.; Sintes, E.; Gasol, J.M.; Herndl, G.J.; Weinbauer, M.G.

    2015-01-01

    Black carbon (BC) is the carbonaceous residue of the incomplete combustion of fossil fuels and biomass and encompasses a range of chemically heterogeneous substances from partly charred plant material to highly condensed soot aerosols. We addressed the potential role of BC aerosol deposition on mari

  4. Molecular simulation of polycyclic aromatic hydrocarbon sorption to black carbon

    NARCIS (Netherlands)

    Haftka, J.J.H.; Parsons, J.R.; Govers, H.A.J.

    2009-01-01

    Strong sorption of hydrophobic organic contaminants to soot or black carbon (BC) is an important environmental process limiting the bioremediation potential of contaminated soils and sediments. Reliable methods to predict BC sorption coefficients for organic contaminants are therefore required. A co

  5. Oxygen reduction in acid media: influence of the activity of CoNPc(1,2) bilayer deposits in relation to their attachment to the carbon black support and role of surface groups as a function of heat treatment

    NARCIS (Netherlands)

    Biloul, A.; Contamin, O.; Scarbeck, G.; Savy, M.; Palys, B.J.; Riga, J.; Verbist, J.

    1994-01-01

    O2 reduction was investigated using rotating disk electrode and voltammetry techniques on NPcCo(1,2) impregnations deposited onto two kinds of carbon black support. They were selected on the basis of their similar pH and dibuthylphthalate (DBP) adsorption values. Samples were also characterized by I

  6. Hydrogen and Carbon Black Production from Thermal Decomposition of Sub-Quality Natural Gas

    Directory of Open Access Journals (Sweden)

    M. Javadi

    2010-03-01

    Full Text Available The objective of this paper is computational investigation of the hydrogen and carbon black production through thermal decomposition of waste gases containing CH4 and H2S, without requiring a H2S separation process. The chemical reaction model, which involves solid carbon, sulfur compounds and precursor species for the formation of carbon black, is based on an assumed Probability Density Function (PDF parameterized by the mean and variance of mixture fraction and β-PDF shape. The effects of feedstock mass flow rate and reactor temperature on hydrogen, carbon black, S2, SO2, COS and CS2 formation are investigated. The results show that the major factor influencing CH4 and H2S conversions is reactor temperature. For temperatures higher than 1100° K, the reactor CH4 conversion reaches 100%, whilst H2S conversion increases in temperatures higher than 1300° K. The results reveal that at any temperature, H2S conversion is less than that of CH4. The results also show that in the production of carbon black from sub-quality natural gas, the formation of carbon monoxide, which is occurring in parallel, play a very significant role. For lower values of feedstock flow rate, CH4 mostly burns to CO and consequently, the production of carbon black is low. The results show that the yield of hydrogen increases with increasing feedstock mass flow rate until the yield reaches a maximum value, and then drops with further increase in the feedstock mass flow rate.

  7. Characterization of PZT/PVC Composites Added with Carbon Black

    Institute of Scientific and Technical Information of China (English)

    LIU Xiaofang; XIONG Chuanxi; SUN Huajun; DONG Lijie; LI Rui; LIU Yang

    2005-01-01

    A new three-phase PZT/ C/ PVC composite comprising PZT (50vol%), nanocrystalline PVC (50 vol% ) and a small volume fraction f of carbon black (C) was prepared by the hot-pressing technique. The dielectric property of the composite as a function of the frequency and the dielectric and piezoelectric properties as a function of the volume fraction f of C were studied. The measured dielectric property demonstrates that a percolation transition occurs in the three-phase composites as in normal two-phase metal-insulator continuum media. The dielectric constant varies slightly with f at f < 0.1 and increases rapidly when f is close to the percolation threshold at 1 kHz. The optimum properties were obtained for f = 0.5 before the percolation threshold in the PZT/ C/ PVC (50/f/(50 - f) vol% ) composite with its d33 (20 pC/N) being 50% higher than that of the PZT/ PVC (50/50vol% ), and its g33(47.23 × 10-3 Vm/N) and Kp (0.25) much higher than the earlier reported values.XRD patterns and P-E hysteresis loops were used to interpret the experimental results.

  8. Conductive additive content balance in Li-ion battery cathodes: Commercial carbon blacks vs. in situ carbon from LiFePO{sub 4}/C composites

    Energy Technology Data Exchange (ETDEWEB)

    Palomares, Veronica; Goni, Aintzane; Muro, Izaskun Gil de; Rojo, Teofilo [Departamento de Quimica Inorganica, Universidad del Pais Vasco UPV/EHU, P.O. Box. 644, 48080, Bilbao (Spain); de Meatza, Iratxe; Bengoechea, Miguel [Energy Department, CIDETEC-IK4, P Miramon 196, Parque Tecnologico de San Sebastian, 20009, San Sebastian (Spain); Cantero, Igor [Departamento I+D+i Nuevas Tecnologias, CEGASA, Artapadura, 11, 01013 Vitoria-Gasteiz (Spain)

    2010-11-15

    Two samples of commercial conducting carbon black and the carbon generated in situ during LiFePO{sub 4}/C composite synthesis from citric acid are studied, with the aim of finding out whether carbon from the composite can fulfil the same function as carbon black in the electrode blend for a Li-ion battery. For this purpose, the carbon samples are analyzed by several techniques, such as X-ray diffraction, Raman spectroscopy, transmission electron microscopy, granulometry, BET specific area and conductivity measurements. Different cathode compositions and component proportions are tested for pellet and cast electrodes. Electrochemical results show that a moderate reduction of commercial carbon black content in both kinds of cathodes, by adding more LiFePO{sub 4}/C composite, enhanced the electrochemical behaviour by around 10%. In situ generated carbon can partially replace commercial conducting carbon black because its high specific surface probably enhances electrolyte penetration into the cathode, but it is always necessary to maintain a minimum amount of carbon black that provides better conductivity in order to obtain a good electrochemical response. (author)

  9. Characterization of Black Carbon Mixing State Field Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Sedlacek, A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Davidovits, P. [Boston College, Chestnut Hill, MA (United States); Lewis, E. R. [Brookhaven National Lab. (BNL), Upton, NY (United States); Onasch, T. B. [Aerodyne Research, Billerica, MA (United States)

    2016-04-01

    Interpreting the temporal relationship between the scattering and incandescence signals recorded by the Single Particle Soot Photometer (SP2), Sedlacek et al. (2012) reported that 60% of the refractory black carbon containing particles in a plume containing biomass burning tracers exhibited non-core-shell structure. Because the relationship between the rBC (refractory black carbon) incandescence and the scattering signals had not been reported in the peer-reviewed literature, and to further evaluate the initial interpretation by Sedlacek et al., a series of experiments was undertaken to investigate black carbon-containing particles of known morphology using Regal black (RB), a proxy for collapsed soot, as the light-absorbing substance to characterize this signal relationship. Particles were formed by coagulation of RB with either a solid substance (sodium chloride or ammonium sulfate) or a liquid substance (dioctyl sebacate), and by condensation with dioctyl sebacate, the latter experiment forming particles in a core-shell configuration. Each particle type experienced fragmentation (observed as negative lagtimes), and each yielded similar lagtime responses in some instances, confounding attempts to differentiate particle morphology using current SP2 lagtime analysis. SP2 operating conditions, specifically laser power and sample flow rate, which in turn affect the particle heating and dissipation rates, play an important role in the behavior of particles in the SP2, including probability of fragmentation. This behavior also depended on the morphology of the particles and on the thermochemical properties of the non-RB substance. Although these influences cannot currently be unambiguously separated, the SP2 analysis may still provide useful information on particle mixing states and black carbon particle sources. This work was communicated in a 2015 publication (Sedlacek et al. 2015)

  10. Phase Transformations of Graphite and Carbon Black by Laser with Low Power Density

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The structure phase transformations of graphite and carbon black induced by pulsed laser were studied in this paper. Under irradiation with laser beam of 1.06μm wavelength and power density of 106 W· cm- 2, both graphite structure and carbon black structure were changed obviously. The results of Raman analyses and Transmission Electron Microscopy (TEM) observations show that graphite transforms into nanodiamond about 5 nm and carbon black is graphitized. It is demonstrated that graphite is the intermediate phase in the transformation from carbon black to diamond, and graphite is easier to transform into diamond by laser irradiation than carbon black.

  11. Centennial black carbon turnover observed in a Russian steppe soil

    Directory of Open Access Journals (Sweden)

    K. Hammes

    2008-02-01

    Full Text Available Black carbon (BC, from incomplete combustion of fuels and biomass, has been considered highly recalcitrant and a substantial sink for carbon dioxide. Recent studies have shown that BC can be degraded. We use soils sampled 100 years apart in a Russian steppe preserve to generate the first whole-profile estimate of BC stocks and turnover in the field. BC stocks (initially 2.5 kg m-2 decreased 25% with cessation of biomass burning. BC turnover in the soil was 293 y (best estimate; range 212–541 y, much faster than inert/passive carbon in soil models. Such results provide a new constraint on theories of soil carbon stabilization. Most importantly, BC cannot be assumed chemically recalcitrant in all soils; other explanations for very old soil carbon are needed.

  12. Dependence of climate forcing and response on the altitude of black carbon aerosols

    Science.gov (United States)

    Ban-Weiss, George A.; Cao, Long; Bala, G.; Caldeira, Ken

    2012-03-01

    Black carbon aerosols absorb solar radiation and decrease planetary albedo, and thus can contribute to climate warming. In this paper, the dependence of equilibrium climate response on the altitude of black carbon is explored using an atmospheric general circulation model coupled to a mixed layer ocean model. The simulations model aerosol direct and semi-direct effects, but not indirect effects. Aerosol concentrations are prescribed and not interactive. It is shown that climate response of black carbon is highly dependent on the altitude of the aerosol. As the altitude of black carbon increases, surface temperatures decrease; black carbon near the surface causes surface warming, whereas black carbon near the tropopause and in the stratosphere causes surface cooling. This cooling occurs despite increasing planetary absorption of sunlight (i.e. decreasing planetary albedo). We find that the trend in surface air temperature response versus the altitude of black carbon is consistent with our calculations of radiative forcing after the troposphere, stratosphere, and land surface have undergone rapid adjustment, calculated as "regressed" radiative forcing. The variation in climate response from black carbon at different altitudes occurs largely from different fast climate responses; temperature dependent feedbacks are not statistically distinguishable. Impacts of black carbon at various altitudes on the hydrological cycle are also discussed; black carbon in the lowest atmospheric layer increases precipitation despite reductions in solar radiation reaching the surface, whereas black carbon at higher altitudes decreases precipitation.

  13. Simplifying the calculation of light scattering properties for black carbon fractal aggregates

    Directory of Open Access Journals (Sweden)

    A. J. A. Smith

    2014-02-01

    Full Text Available Black carbon fractal aggregates have complicated shapes that make the calculation of their optical properties particularly computationally expensive. Here, a method is presented to estimate fractal aggregate light scattering properties by optimising simplified models to full light scattering calculations. It is found that there are no possible spherical models (at any size or refractive index that well represent the light scattering in the visible, or near-thermal infrared. As such, parameterisations of the light scattering as a function of the number of aggregate particles is presented as the most pragmatic choice for modelling distributions of black carbon when the large computational overheads of rigorous scattering calculations cannot be justified. This parameterisation can be analytically integrated to provide light scattering properties for log-normal distributions of black carbon fractal aggregates and return extinction cross-sections with 0.1% accuracy for typical black carbon size distributions. Scattering cross-sections and the asymmetry parameter can be obtained to within 3%.

  14. Preparation and characterization of dopamine-decorated hydrophilic carbon black

    Energy Technology Data Exchange (ETDEWEB)

    Zhu Lijun; Lu Yonglai [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Key Laboratory of Beijing City on Preparation and Processing of Novel Polymer Materials, Beijing 100029 (China); Wang Yiqing [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Key Laboratory of Carbon Fiber and Functional Polymers, Ministry of Education, Beijing 100029 (China); Zhang Liqun [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Key Laboratory of Beijing City on Preparation and Processing of Novel Polymer Materials, Beijing 100029 (China); Wang Wencai, E-mail: wangw@mail.buct.edu.cn [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Key Laboratory of Carbon Fiber and Functional Polymers, Ministry of Education, Beijing 100029 (China)

    2012-05-01

    Inspired by the bio-adhesive proteins secreted by mussels for attachment to almost all wet substrates, a facile method involving oxidative polymerization of dopamine was proposed to prepare highly hydrophilic carbon black (CB) particles. A self-assembled polydopamine (PDA) ad-layer was formed via the oxidative polymerization of dopamine on the surface of CB simply by dipping the CB into an alkaline dopamine solution and mildly stirring at room temperature. The process is simple, controllable, and environment-friendly. The surface composition and structure of the CB were characterized by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The surface morphology of the CB was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results showed that the PDA ad-layer was successfully deposited on the CB surfaces. The PDA-functionalized CB (CB-PDA) gave a stable colloidal dispersion in water. Contact angle measurement results indicated that the hydrophilicity of CB was significantly improved after dopamine modification. TGA results confirmed that the modified CB maintained good heat resistance. The method provided a facile route to prepare hydrophilic CB having terminal hydroxyl groups.

  15. Wetting and Non-Wetting Models of Black Carbon Activation

    Science.gov (United States)

    Henson, B. F.; Laura, S.

    2006-12-01

    We present the results of recent modeling studies on the activation of black carbon (BC) aerosol to form cloud condensation nuclei (CCN). We use a model of BC activation based on a general modification of the Koehler equation for insoluble activation in which we introduce a term based on the activity of water adsorbed on the particle surface. We parameterize the model using the free energy of adsorption, a parameter directly comparable to laboratory measurements of water adsorption on carbon. Although the model of the water- surface interaction is general, the form of the activation equation that results depends upon a further model of the distribution of water on the particle. One possible model involves the symmetric growth of a water shell around the isoluble particle core (wetting). This model predicts upper and lower bounding curves for the activation supersaturation given by the range of water interaction energies from hydrophobic to hydrophilic which are in agreement with a large body of recent activation data. The resulting activation diameters are from 3 to 10 times smaller than activation of soluble particles of identical dry diameter. Another possible model involves an exluded liquid droplet growing in contact with the particle (non-wetting). The geometry of this model much more resembles classic assumptions of heterogeneous nucleation theory. This model can yield extremely high activation supersaturation as a function of diameter, as has been observed in some experiments, and enables calculations in agreement with some of these results. We discuss these two geometrical models of water growth, the different behaviors predicted by the resulting activation equation, and the means to determine which model of growth is appropriate for a given BC particle characterized by either water interaction energy or morphology. These simple models enable an efficient and physically reasonable means to calculate the activation of BC aerosol to form CCN based upon a

  16. Oxidation behavior of a kind of carbon black

    Institute of Scientific and Technical Information of China (English)

    TANG JunShi; SONG Qiang; HE BaiLei; YAO Qiang

    2009-01-01

    The DTG curves of a kind of carbon black during TPO tests were found to have multiple peaks with an unusual sharp peak after the main peak. TPO tests with different sample loads, oxygen fractions and heating rates were carried out to study the influence of the experimental parameters on the sharp peak. The results show that the sharp peak is not caused by heat and mass transfer limitations, but by the intrinsic oxidation kinetics of the carbon black. The evolution of the specific surface area during the intrinsic kinetic controlled oxidation process was then analyzed using isothermal oxidation at low temperatures which showed that the sharp peak is caused by the increase of the specific surface area. The pore structure changes greatly influence the oxidation process when the reaction is controlled by the intrinsic kinetics. When there were no heat and mass transfer limitations, the different oxidation processes result in the same specific surface area evolution.

  17. Electromagnetic properties of carbon black and barium titanate composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Wang Guiqin [School of Material Science and Engineering, Dalian University of Technology, Dalian 116023 (China)], E-mail: c2b2chen@163.com; Chen Xiaodong; Duan Yuping; Liu Shunhua [School of Material Science and Engineering, Dalian University of Technology, Dalian 116023 (China)

    2008-04-24

    Nanocrystalline carbon black/barium titanate compound particle (CP) was synthesized by sol-gel method. The phase structure and morphology of compound particle were investigated by X-ray diffraction (XRD), transmission electron microscope (TEM) and Raman spectrum measurements, the electroconductivity was test by trielectrode arrangement and the precursor powder was followed by differential scanning calorimetric measurements (DSC) and thermal gravimetric analysis (TGA). In addition, the complex relative permittivity and permeability of compound particle were investigated by reflection method. The compound particle/epoxide resin composite (CP/EP) with different contents of CP were measured. The results show barium titanate crystal is tetragonal phase and its grain is oval shape with 80-100 nm which was coated by carbon black film. As electromagnetic (EM) complex permittivity, permeability and reflection loss (RL) shown that the compound particle is mainly a kind of electric and dielectric lossy materials and exhibits excellent microwave absorption performance in the X- and Ku-bands.

  18. Final recommendations for reference materials in black carbon analysis

    Science.gov (United States)

    Schmidt, Michael W. I.; Masiello, Caroline A.; Skjemstad, Jan O.

    Last summer, a symposium was held to discuss aspects of global biogeochemical cycles, including organic matter cycling in soils, rivers, and marine environments; black carbon particle fluxes and the biological pump; dissolved organic matter; and organic matter preservation. Seventy scientists from various disciplines, including oceanography, soil science, geology, and chemistry attended the 3-day meeting at the Friday Harbor Laboratories, a research station of the University of Washington.“New Approaches in Marine Organic Biogeochemistry” commemorated the life and science of a colleague and friend, John I. Hedges, who was also involved in several groups developing chemical reference materials. Part of this symposium included a workshop on chemical reference materials, where final recommendations of the Steering Committee for Black Carbon Reference Materials were presented.

  19. Evaluation of the genetic activity of industrially produced carbon black.

    Science.gov (United States)

    Kirwin, C J; LeBlanc, J V; Thomas, W C; Haworth, S R; Kirby, P E; Thilagar, A; Bowman, J T; Brusick, D J

    1981-06-01

    Commercially produced oil furnace carbon black (Chemical Abstract Service Registry No. 1333-86-4) has been evaluated by five different assay for genetic activity. These were the Ames Salmonella typhimurium reverse mutation test, sister chromatid exchange test in CHO cells, mouse lymphoma test, cell transformation assay in C3H/10T1/2 cells, and assay for genetic effects in Drosophila melanogaster. Limited cellular toxicity was exhibited but no significant genetic activity was noted.

  20. Laboratory estimation of black carbon emissions from cookstoves

    OpenAIRE

    Sota, Candela de la; Kane, M.; M. Viana; Lumbreras Martin, Julio; Ba, M.B.; Querol, Xavier; Mazorra, J.; Narros Sierra, Adolfo; Borge, R.; Youm, I.

    2016-01-01

    Recent estimations show that residential solid fuel combustion accounts for 25% of global black carbon (BC) emissions (Lamarque et al., 2010). Thus, the control of these emissions through the implementation of cleaner cooking technologies could be crucial for climate change mitigation (Venkataraman et al., 2005). However, BC emission factors for biofuel cooking stoves have been poorly estimated due to the wide distribution and remote location of the stoves and the relatively complex existing ...

  1. Quantification of extraneous carbon during compound specific radiocarbon analysis of black carbon.

    Science.gov (United States)

    Ziolkowski, Lori A; Druffel, Ellen R M

    2009-12-15

    Radiocarbon ((14)C) is a radioactive isotope that is useful for determining the age and cycling of carbon-based materials in the Earth system. Compound specific radiocarbon analysis (CSRA) provides powerful insight into the turnover of individual components that make up the carbon cycle. Extraneous or nonspecific background carbon (C(ex)) is added during sample processing and subsequent isolation of CSRA samples. Here, we evaluate the quantity and radiocarbon signature of C(ex) added from two sources: preparative capillary gas chromatography (PCGC, C(PCGC)) and chemical preparation of CSRA of black carbon samples (C(chemistry)). We evaluated the blank directly using process blanks and indirectly by quantifying the difference in the isotopic composition between processed and unprocessed samples for a range of sample sizes. The direct and indirect assessment of C(chemistry+PCGC) agree, both in magnitude and radiocarbon value (1.1 +/- 0.5 microg of C, fraction modern = 0.2). Half of the C(ex) is introduced before PCGC isolation, likely from coeluting compounds in solvents used in the extraction method. The magnitude of propagated uncertainties of CSRA samples are a function of sample size and collection duration. Small samples collected for a brief amount of time have a smaller propagated (14)C uncertainty than larger samples collected for a longer period of time. CSRA users are cautioned to consider the magnitude of uncertainty they require for their system of interest, to frequently evaluate the magnitude of C(ex) added during sampling processing, and to avoid isolating samples < or = 5 microg of carbon.

  2. Barrow Black Carbon Source and Impact Study Final Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, Tate [Baylor Univ., Waco, TX (United States)

    2014-07-01

    The goal of the Barrow Black Carbon Source and Impact (BBCSI) Study was to characterize the concentration and isotopic composition of carbonaceous atmospheric particulate matter (PM) at the Atmospheric Radiation Measurement site in Barrow, AK. The carbonaceous component was characterized via measurement of the organic and black carbon (OC and BC) components of the total PM. To facilitate complete characterization of the particulate matter, filter-based collections were used, including a medium volume PM2.5 sampler and a high volume PM10 sampler. Thirty-eight fine (PM2.5) and 49 coarse (PM10) particulate matter fractions were collected at weekly and bi-monthly intervals. The PM2.5 sampler operated with minimal maintenance during the 12 month campaign. The PM10 sampler used for the BBCSI used standard Tisch hi-vol motors which have a known lifetime of ~1 month under constant use; this necessitated monthly maintenance and it is suggested that the motors be upgraded to industrial blowers for future deployment in the Arctic. The BBCSI sampling campaign successfully collected and archived 87 ambient atmospheric particulate matter samples from Barrow, AK from July 2012 to June 2013. Preliminary analysis of the organic and black carbon concentrations has been completed. This campaign confirmed known trends of high BC lasting from the winter through to spring haze periods and low BC concentrations in the summer.

  3. Worker exposure to ultrafine particles during carbon black treatment

    Directory of Open Access Journals (Sweden)

    Urszula Mikołajczyk

    2015-07-01

    Full Text Available Background: The aim of the project was to assess the exposure of workers to ultrafine particles released during handling and packing of carbon black. The assessment included the results of the measurements performed in a carbon black handling plant before, during, and after work shift. Material and Methods: The number concentration of particles within the dimension range 10–1000 nm and 10–100 nm was assayed by a condensation particle counter (CPC. The mass concentration of particles was determined by a DustTrak II DRX aerosol concentration monitor. The surface area concentration of the particles potentially deposited in the alveolar (A and tracheo-bronchial (TB regions was estimated by an AeroTrak 9000 nanoparticle monitor. Results: An average mass concentration of particles during the process was 6-fold higher than that before its start, while a 3-fold increase in the average number concentration of particles within the dimension range 10–1000 nm and 10–100 nm was observed during the process. At the same time a 4-fold increase was found in the surface area concentration of the particles potentially deposited in the A and TB regions. Conclusions: During the process of carbon black handling and packing a significantly higher values of each of the analysed parameters, characterizing the exposure to ultrafine particles, were noted. Med Pr 2015;66(3:317–326

  4. Personal exposure to Black Carbon in transport microenvironments

    Science.gov (United States)

    Dons, Evi; Int Panis, Luc; Van Poppel, Martine; Theunis, Jan; Wets, Geert

    2012-08-01

    We evaluated personal exposure of 62 individuals to the air pollutant Black Carbon, using 13 portable aethalometers while keeping detailed records of their time-activity pattern and whereabouts. Concentrations encountered in transport are studied in depth and related to trip motives. The evaluation comprises more than 1500 trips with different transport modes. Measurements were spread over two seasons. Results show that 6% of the time is spent in transport, but it accounts for 21% of personal exposure to Black Carbon and approximately 30% of inhaled dose. Concentrations in transport were 2-5 times higher compared to concentrations encountered at home. Exposure was highest for car drivers, and car and bus passengers. Concentrations of Black Carbon were only half as much when traveling by bike or on foot; when incorporating breathing rates, dose was found to be twice as high for active modes. Lowest 'in transport' concentrations were measured in trains, but nevertheless these concentrations are double the concentrations measured at home. Two thirds of the trips are car trips, and those trips showed a large spread in concentrations. In-car concentrations are higher during peak hours compared to off-peak, and are elevated on weekdays compared to Saturdays and even more so on Sundays. These findings result in significantly higher exposure during car commute trips (motive 'Work'), and lower concentrations for trips with motive 'Social and leisure'. Because of the many factors influencing exposure in transport, travel time is not a good predictor of integrated personal exposure or inhaled dose.

  5. Adsorption ability of the carbon black for nickel ions uptake from aqueous solution

    OpenAIRE

    Rađenović Ankica; Malina Jadranka

    2013-01-01

    Surface modification can be performed by adsorption of certain organic compounds on the surface of carbon. The main objective of this work was to compare the adsorption ability of acid-modified carbon black with the non-modified one. Modification process was performed by adsorption of acetic acid onto commercial carbon black surface. A batch adsorption system was applied to study the both adsorption reaction, acetic acid and Ni(II) adsorption onto the carbon black. Adsorption isotherms ...

  6. Analysis of transpacific transport of black carbon during HIPPO-3: implications for black carbon aging

    Directory of Open Access Journals (Sweden)

    Z. Shen

    2014-01-01

    Full Text Available Long-range transport of black carbon (BC is a growing concern as a result of the efficiency of BC in warming the climate and its adverse impact on human health. We study transpacific transport of BC during HIPPO-3 using a combination of inverse modeling and sensitivity analysis. We use the GEOS-Chem chemical transport model and its adjoint to constrain Asian BC emissions and estimate the source of BC over the North Pacific. We find that different sources of BC dominate the transport to the North Pacific during the southbound (29 March 2010 and northbound (13 April 2010 measurements in HIPPO-3. While biomass burning in Southeast Asia (SE contributes about 60% of BC in March, more than 90% of BC comes from fossil fuel and biofuel combustion in East Asia (EA during the April mission. GEOS-Chem simulations generally resolve the spatial and temporal variation of BC concentrations over the North Pacific, but are unable to reproduce the low and high tails of the observed BC distribution. We find that the optimized BC emissions derived from inverse modeling fail to improve model simulations significantly. This failure indicates that uncertainties in BC transport, rather than in emissions, account for the major biases in GEOS-Chem simulations of BC. The aging process, transforming BC from hydrophobic into hydrophilic form, is one of the key factors controlling wet scavenging and remote concentrations of BC. Sensitivity tests on BC aging suggest that the aging time scale of anthropogenic BC from EA is several hours, faster than assumed in most global models, while the aging process of biomass burning BC from SE may occur much slower, with a time scale of a few days. To evaluate the effects of BC aging and wet deposition on transpacific transport of BC, we develop an idealized model of BC transport. We find that the mid-latitude air masses sampled during HIPPO-3 may have experienced a series of precipitation events, particularly near the EA and SE source

  7. Selective functionalization of carbon nanotubes

    Science.gov (United States)

    Strano, Michael S. (Inventor); Usrey, Monica (Inventor); Barone, Paul (Inventor); Dyke, Christopher A. (Inventor); Tour, James M. (Inventor); Kittrell, W. Carter (Inventor); Hauge, Robert H. (Inventor); Smalley, Richard E. (Inventor)

    2009-01-01

    The present invention is directed toward methods of selectively functionalizing carbon nanotubes of a specific type or range of types, based on their electronic properties, using diazonium chemistry. The present invention is also directed toward methods of separating carbon nanotubes into populations of specific types or range(s) of types via selective functionalization and electrophoresis, and also to the novel compositions generated by such separations.

  8. Black-carbon absorption enhancement in the atmosphere determined by particle mixing state

    Science.gov (United States)

    Liu, Dantong; Whitehead, James; Alfarra, M. Rami; Reyes-Villegas, Ernesto; Spracklen, Dominick V.; Reddington, Carly L.; Kong, Shaofei; Williams, Paul I.; Ting, Yu-Chieh; Haslett, Sophie; Taylor, Jonathan W.; Flynn, Michael J.; Morgan, William T.; McFiggans, Gordon; Coe, Hugh; Allan, James D.

    2017-02-01

    Atmospheric black carbon makes an important but poorly quantified contribution to the warming of the global atmosphere. Laboratory and modelling studies have shown that the addition of non-black-carbon materials to black-carbon particles may enhance the particles’ light absorption by 50 to 60% by refracting and reflecting light. Real-world experimental evidence for this `lensing’ effect is scant and conflicting, showing that absorption enhancements can be less than 5% or as large as 140%. Here we present simultaneous quantifications of the composition and optical properties of individual atmospheric black-carbon particles. We show that particles with a mass ratio of non-black carbon to black carbon of less than 1.5, which is typical of fresh traffic sources, are best represented as having no absorption enhancement. In contrast, black-carbon particles with a ratio greater than 3, which is typical of biomass-burning emissions, are best described assuming optical lensing leading to an absorption enhancement. We introduce a generalized hybrid model approach for estimating scattering and absorption enhancements based on laboratory and atmospheric observations. We conclude that the occurrence of the absorption enhancement of black-carbon particles is determined by the particles’ mass ratio of non-black carbon to black carbon.

  9. Thermal Analysis Characterization of Elastomers and Carbon Black Filled Rubber Composites for Army Applications

    Science.gov (United States)

    1985-06-01

    Organ~ce, 60.40 % Carbon Black, 36.15 450(S) 2 Carbon black, 36.40 500 % Residue, 2.09 410(SH) 2 Residue, 3.20 22 2 Organica , 64.99 2 Organics, 62.97 2...64.92 1 Organics, 62.30 I Carbon Black, 31.42 395(S) I Carbon Black, 34.02 420 Z Residue, 3.66 440(SR) 1 Reuidue, 3.69 73 - C I Organica , 6’.33 470... Organica , 62.80 % Organics, 62.80 % Carbon black, 36.27 470(S) 2 Carbon black, It.60 505 2 Residue, 0.963 435(51) 2 Residue, 1.60 Iii 2 Organics

  10. Chemical and biological oxidative effects of carbon black nanoparticles.

    Science.gov (United States)

    Koike, Eiko; Kobayashi, Takahiro

    2006-11-01

    Several studies show that ultrafine particles have a larger surface area than coarse particles, thus causing a greater inflammatory response. In this study, we investigated chemical and biological oxidative effects of nanoparticles in vitro. Carbon black (CB) nanoparticles with mean aerodynamic diameters of 14, 56, and 95nm were examined. The innate oxidative capacity of the CB nanoparticles was measured by consumption of dithiothreitol (DTT) in cell-free system. The expression of heme oxygenase-1 (HO-1) in rat alveolar type II epithelial cell line (SV40T2) and alveolar macrophages (AM) exposed to CB nanoparticles was measured by ELISA. DTT consumption of 14nm CB was higher than that of other CB nanoparticles having the same particle weight. However, DTT consumption was directly proportional to the particle surface area. HO-1 protein in SV40T2 cells was significantly increased by the 14nm and 56nm CB, however, 95nm CB did not affect. HO-1 protein in AM was significantly increased by the 14, 56, and 95nm CB. The increase in HO-1 expression was diminished by N-acetyl-l-cysteine (NAC) treatment of each CB nanoparticles before exposure although the difference between the effects of NAC-treated and untreated 14nm CB did not achieve significant. In conclusion, CB nanoparticles have innate oxidative capacity that may be dependent on the surface area. CB nanoparticles can induce oxidative stress in alveolar epithelial cells and AM that is more prominent with smaller particles. The oxidative stress may, at least partially, be mediated by surface function of particles.

  11. Biomass burning in boreal forests and peatlands: Effects on ecosystem carbon losses and soil carbon stabilization as black carbon

    Science.gov (United States)

    Turetsky, M. R.; Kane, E. S.; Benscoter, B.

    2011-12-01

    Climate change has increased both annual area burned and the severity of biomass combustion in some boreal regions. For example, there has been a four-fold increase in late season fires in boreal Alaska over the last decade relative to the previous 50 years. Such changes in the fire regime are expected to stimulate ecosystem carbon losses through fuel combustion, reduced primary production, and increased decomposition. However, biomass burning also will influence the accumulation of black carbon in soils, which could promote long-term soil carbon sequestration. Variations in slope and aspect regulate soil temperatures and drainage conditions, and affect the development of permafrost and thick peat layers. Wet soil conditions in peatlands and permafrost forests often inhibit combustion during wildfires, leading to strong positive correlations between pre- and post- fire organic soil thickness that persist through multiple fire cycles. However, burning can occur in poorly drained ecosystems through smouldering combustion, which has implications for emission ratios of CO2:CH4:CO as well as black carbon formation. Our studies of combustion severity and black carbon concentrations in boreal soils show a negative relationship between concentrations of black carbon and organic carbon in soils post-fire. Relative to well drained stands, poorly drained sites with thick peat layers (such as north-facing stands) had less severe burning and low concentrations of black carbon in mineral soils post-fire. Conversely, drier forests lost a greater proportion of their organic soils during combustion but retained larger black carbon stocks following burning. Overall, we have quantified greater black carbon concentrations in surface mineral soil horizons than in organic soil horizons. This is surprising given that wildfires typically do not consume the entire organic soil layer in boreal forests, and could be indicative of the vulnerability of black carbon formed in organic horizons

  12. Black Carbon in Estuarine and Coastal Ocean Dissolved Organic Matter

    Science.gov (United States)

    Mannino, Antonio; Harvey, H. Rodger

    2003-01-01

    Black carbon (BC) in ultrafiltered high-molecular-weight DOM (UDOM) was measured in surface waters of Delaware Bay, Chesapeake Bay and the adjacent Atlantic Ocean (USA) to ascertain the importance of riverine and estuarine DOM as a source of BC to the ocean. BC comprised 5-72% of UDOM-C (27+/-l7%) and on average 8.9+/-6.5% of dissolved organic carbon (DOC) with higher values in the turbid region of the Delaware Estuary and lower yields in the river and coastal ocean. The spatial and seasonal distributions of BC along the salinity gradient of Delaware Bay suggest that the higher levels of BC in surface water UDOM originated from localized sources, possibly from atmospheric deposition or released from resuspended sediments. Black carbon comprised 4 to 7% of the DOC in the coastal Atlantic Ocean, revealing that river-estuary systems are important exporters of colloidal BC to the ocean. The annual flux of BC from Delaware Bay UDOM to the Atlantic Ocean was estimated at 2.4x10(exp 10) g BC yr(exp -1). The global river flux of BC through DOM to the ocean could be on the order of 5.5x1O(exp 12)g BC yr (exp -1). These results support the hypothesis that the DOC pool is the intermediate reservoir in which BC ages prior to sedimentary deposition.

  13. 20 years of Black Carbon measurements in Germany

    Science.gov (United States)

    Kutzner, Rebecca; Quedenau, Jörn; Kuik, Friderike; von Schneidemesser, Erika; Schmale, Julia

    2016-04-01

    Black Carbon (BC) is an important short-lived climate-forcing pollutant contributing to global warming through absorption of sunlight. At the same time, BC, as a component of particulate matter (PM) exerts adverse health effects, like decreased lung function and exacerbated asthma. Globally, anthropogenic emission sources of BC include residential heating, transport, and agricultural fires, while the dominant natural emission sources are wildfires. Despite the various adverse effects of BC, legislation that requires mandatory monitoring of BC concentrations does not currently exist in the European Union. Instead, BC is only indirectly monitored as component of PM10 and PM2.5 (particulate matter with a diameter smaller 10 μm and 2.5 μm). Before the introduction of mandatory PM10 and PM2.5 monitoring in the European Union in 2005 and 2015, respectively, 'black smoke', a surrogate for BC, was a required measurement in Germany from the early 1990s. The annual mean limit value was 14 μg m-3 from 1995 and 8 μg m-3 from 1998 onwards. Many 'black smoke' measurements were stopped in 2004, with the repeal of the regulations obtaining at the time. However, in most German federal states a limited number BC monitoring stations continued to operate. Here we present a synthesis of BC data from 213 stations across Germany covering the period between 1994 and 2014. Due to the lack of a standardized method and respective legislation, the data set is very heterogeneous relying on twelve different measurement methods including chemical, optical, and thermal-optical methods. Stations include locations classified as background, urban-background, industrial and traffic among other types. Raw data in many different formats has been modelled and integrated in a relational database, allowing various options for further data analysis. We highlight results from the year 2009, as it is the year with the largest measurement coverage based on the same measurement method, with 30 stations. In

  14. Black Carbon Emissions from Associated Natural Gas Flaring.

    Science.gov (United States)

    Weyant, Cheryl L; Shepson, Paul B; Subramanian, R; Cambaliza, Maria O L; Heimburger, Alexie; McCabe, David; Baum, Ellen; Stirm, Brian H; Bond, Tami C

    2016-02-16

    Approximately 150 billion cubic meters (BCM) of natural gas is flared and vented in the world annually, emitting greenhouse gases and other pollutants with no energy benefit. About 7 BCM per year is flared in the United States, and half is from North Dakota alone. There are few emission measurements from associated gas flares and limited black carbon (BC) emission factors have been previously reported from the field. Emission plumes from 26 individual flares in the Bakken formation in North Dakota were sampled. Methane, carbon dioxide, and BC were measured simultaneously, allowing the calculation of BC mass emission factors using the carbon balance method. Particle optical absorption was measured using a three-wavelength particle soot absorption photometer (PSAP) and BC particle number and mass concentrations were measured with a single particle soot photometer. The BC emission factors varied over 2 orders of magnitude, with an average and uncertainty range of 0.14 ± 0.12 g/kg hydrocarbons in associated gas and a median of 0.07 g/kg which represents a lower bound on these measurements. An estimation of the BC emission factor derived from PSAP absorption provides an upper bound at 3.1 g/kg. These results are lower than previous estimations and laboratory measurements. The BC mass absorption cross section was 16 ± 12 m(2)/g BC at 530 nm. The average absorption Ångström exponent was 1.2 ± 0.8, suggesting that most of the light absorbing aerosol measured was black carbon and the contribution of light absorbing organic carbon was small.

  15. Centennial black carbon turnover observed in a Russia steppe soil

    Energy Technology Data Exchange (ETDEWEB)

    Hammes, K.; Torn, M.S.; Lapenas, A.G.; Schmidt, M.W.I.

    2008-09-15

    Black carbon (BC), from incomplete combustion of fuels and biomass, has been considered highly recalcitrant and a substantial sink for carbon dioxide. Recent studies have shown that BC can be degraded in soils. We use two soils with very low spatial variability sampled 100 years apart in a Russian steppe preserve to generate the first whole-profile estimate of BC stocks and turnover in the field. Quantities of fire residues in soil changed significantly over a century. Black carbon stock was 2.5 kg m{sup -2}, or about 7-10% of total organic C in 1900. With cessation of biomass burning, BC stocks decreased 25% over a century, which translates into a centennial soil BC turnover (293 years best estimate; range 182-541 years), much faster than so-called inert or passive carbon in ecosystem models. The turnover time presented here is for loss by all processes, namely decomposition, leaching, and erosion, although the latter two were probably insignificant in this case. Notably, at both time points, the peak BC stock was below 30 cm, a depth interval, which is not typically accounted for. Also, the quality of the fire residues changed with time, as indicated by the use benzene poly carboxylic acids (BPCA) as molecular markers. The proportions of less-condensed (and thus more easily degradable) BC structures decreased, whereas the highly condensed (and more recalcitrant) BC structures survived unchanged over the 100-year period. Our results show that BC cannot be assumed chemically recalcitrant in all soils, and other explanations for very old soil carbon are needed.

  16. Barrow Black Carbon Source and Impact Study Final Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, Tate

    2014-07-01

    The goal of the Barrow Black Carbon Source and Impact campaign was to characterize the concentration and isotopic composition of carbonaceous atmospheric particulate matter (PM) at the Atmospheric Radiation Measurement (ARM) Climate Research Facility site in Barrow, Alaska. The carbonaceous component was characterized by measuring the organic and black carbon (OC and BC) components of the total PM. To facilitate complete characterization of the PM, filter-based collections were used, including a medium volume PM2.5 sampler and a high volume PM10 sampler. Thirty-eight fine PM fractions (PM2.5) and 49 coarse (PM10) PM fractions were collected at weekly and bi-monthly intervals. The PM2.5 sampler operated with minimal maintenance during the 12 month campaign. The PM10 sampler used for the Barrow Black Carbon Source and Impact (BBCSI) study used standard Tisch “hi-vol” motors that have a known lifetime of approximately 1 month under constant use; this necessitated monthly maintenance, and it is suggested that, for future deployment in the Arctic, the motors be upgraded to industrial blowers. The BBCSI sampling campaign successfully collected and archived 87 ambient atmospheric PM samples from Barrow, Alaska, from July 2012 to June 2013. Preliminary analysis of the OC and BC concentrations has been completed. This campaign confirmed known trends of high BC lasting from the winter through to spring haze periods and low BC concentrations in the summer. However, the annual OC concentrations had a very different seasonal pattern with the highest concentrations during the summer, lowest concentrations during the fall, and increased concentrations during the winter and spring (Figure 1).

  17. Mesozoic black shales, source mixing and carbon isotopes

    Science.gov (United States)

    Suan, Guillaume

    2016-04-01

    Over the last decades, considerable attention has been devoted to the paleoenvironmental and biogeochemical significance of Mesozoic black shales. Black shale-bearing successions indeed often display marked changes in the organic carbon isotope composition (δ13Corg), which have been commonly interpreted as evidence for dramatic perturbations of global carbon budgets and CO2 levels. Arguably the majority of these studies have discarded some more "local" explanations when interpreting δ13Corg profiles, most often because comparable profiles occur on geographically large and distant areas. Based on newly acquired data and selected examples from the literature, I will show that the changing contribution of organic components with distinct δ13C signatures exerts a major but overlooked influence of Mesozoic δ13Corg profiles. Such a bias occurs across a wide spectrum of sedimentological settings and ages, as shown by the good correlation between δ13Corg values and proxies of kerogen proportions (such as rock-eval, biomarker, palynofacies and palynological data) recorded in Mesozoic marginal to deep marine successions of Triassic, Jurassic and Cretaceous age. In most of these successions, labile, 12C-enriched amorphous organic matter of marine origin dominates strata deposited under anoxic conditions, while oxidation-resistant, 13C-rich terrestrial particles dominate strata deposited under well-oxygenated conditions. This influence is further illustrated by weathering profiles of Toarcian (Lower Jurassic) black shales from France, where weathered areas dominated by refractory organic matter show dramatic 13C-enrichment (and decreased total organic carbon and pyrite contents) compared to non-weathered portions of the same horizon. The implications of these results for chemostratigraphic correlations and pCO2 reconstructions of Mesozoic will be discussed, as well as strategies to overcome this major bias.

  18. Seasonal features of black carbon measured at Syowa Station, Antarctica

    Science.gov (United States)

    Hara, K.; Osada, K.; Yabuki, M.; Shiobara, M.; Yamanouchi, T.

    2015-12-01

    Black carbon (BC) is one of important aerosol constituents because the strong light absorption ability. Low concentrations of aerosols and BC let BC make insignificant contribution to aerosol radiative forcing in the Antarctica at the moment. Because of less or negligible source strength of BC in the Antarctic circle, BC can be used as a tracer of transport from the mid-latitudes. This study aims to understand seasonal feature, transport pathway, and origins of black carbon in the Antarctic coats. Black carbon measurement has been made using 7-wavelength aethalometer at Syowa Station, Antarctica since February, 2005. Mass BC concentrations were estimated from light attenuation by Weingartner's correction procedure (Weingartner et al., 2003) in this study. Detection limit was 0.2 - 0.4 ng/m3 in our measurement conditions (2-hour resolution and flow rate of ca. 10LPM). BC concentrations ranged from near detection limit to 55.7 ng/m3 at Syowa Station, Antarctica during the measurements. No trend has been observed since February, 2005. High BC concentrations were coincident with poleward flow from the mid-latitudes under the storm conditions by cyclone approach, whereas low BC concentrations were found in transport from coastal regions and the Antarctic continent. Considering that outflow from South America and Southern Africa affect remarkably air quality in the Southern Ocean of Atlantic and Indian Ocean sectors, BC at Syowa Station might be originated from biomass burning and human activity on South America and Southern Africa. Seasonal features of BC at Syowa Station shows maximum in September - October and lower in December - April. Spring maximum in September - October was obtained at the other Antarctic stations (Neumayer, Halley, South pole, and Ferraz). Although second maximum was found in January at the other stations, the maximum was not observed at Syowa Station.

  19. World Carbon Black Output to Reach 12.7 Million Tons in 2015

    Institute of Scientific and Technical Information of China (English)

    Zhu Yongkang

    2012-01-01

    From April 13 to April 17, "Carbon Black China of 2012" (CBC2012) was held in Hangzhou, China. Mr. Paul Ita, the president of US marketing research institution Notch Consulting Group, announced that the prospect of carbon black industry was closely linked with the development of auto industry and tire industry. The demand for carbon black of 2010 increased by 15% compared with that of 2009; the growth rate of demand for carbon black was 5.8% in 2011 and the total output was 10.7 million tons, which increased by about 5.5% compared with that of 2010.

  20. Recommendations for the interpretation of "black carbon" measurements

    Directory of Open Access Journals (Sweden)

    A. Petzold

    2013-04-01

    Full Text Available Although black carbon (BC is one of the key atmospheric particulate components driving climate change and air quality, there is no agreement on the terminology that considers all aspects of specific properties, definitions, measurement methods, and related uncertainties. As a result, there is much ambiguity in the scientific literature of measurements and numerical models that refer to BC with different names and based on different properties of the particles, with no clear definition of the terms. The authors present here a recommended terminology to clarify the terms used for BC in atmospheric research, with the goal of establishing unambiguous links between terms, targeted material properties and associated measurement techniques.

  1. Modal character of atmospheric black carbon size distributions

    Science.gov (United States)

    Berner, A.; Sidla, S.; Galambos, Z.; Kruisz, C.; Hitzenberger, R.; ten Brink, H. M.; Kos, G. P. A.

    1996-08-01

    Samples of atmospheric aerosols, collected with cascade impactors in the urban area of Vienna (Austria) and at a coastal site on the North Sea, were investigated for black carbon (BC) as the main component of absorbing material and for mass. The size distributions are structured. The BC distributions of these samples show a predominant mode, the accumulation aerosol, in the upper submicron size range, a less distinct finer mode attributable to fresh emissions from combustion sources, and a distinct coarse mode of unclear origin. It is important to note that some parameters of the accumulation aerosol are related statistically, indicating the evolution of the atmospheric accumulation aerosol.

  2. Black carbon concentrations and mixing state in the Finnish Arctic

    Science.gov (United States)

    Raatikainen, T.; Brus, D.; Hyvärinen, A.-P.; Svensson, J.; Asmi, E.; Lihavainen, H.

    2015-09-01

    Atmospheric aerosol composition was measured using a Single Particle Soot Photometer (SP2) in the Finnish Arctic during winter 2011-2012. The Sammaltunturi measurement site at the Pallas GAW (Global Atmosphere Watch) station receives air masses from different source regions including the Arctic Ocean and continental Europe. The SP2 provides detailed information about mass distributions and mixing state of refractory black carbon (rBC). The measurements showed widely varying rBC mass concentrations (0-120 ng m-3), which were related to varying contributions of different source regions and aerosol removal processes. The rBC mass was log-normally distributed showing a relatively constant rBC core mass mean diameter with an average of 194 nm (75-655 nm sizing range). On average, the number fraction of particles containing rBC was 0.24 (integrated over 350-450 nm particle diameter range) and the average particle diameter to rBC core volume equivalent diameter ratio was 2.0 (averaged over particles with 150-200 nm rBC core volume equivalent diameters). These average numbers mean that the observed rBC core mass mean diameter is similar to those of aged particles, but the observed particles seem to have unusually high particle to rBC core diameter ratios. Comparison of the measured rBC mass concentration with that of the optically detected equivalent black carbon (eBC) using an Aethalometer and a MAAP showed that eBC was larger by a factor of five. The difference could not be fully explained without assuming that only a part of the optically detected light absorbing material is refractory and absorbs light at the wavelength used by the SP2. Finally, climate implications of five different black carbon mixing state representations were compared using the Mie approximation and simple direct radiative forcing efficiency calculations. These calculations showed that the observed mixing state means significantly lower warming effect or even a net cooling effect when compared with

  3. Climate effects of black carbon aerosols in China and India.

    Science.gov (United States)

    Menon, Surabi; Hansen, James; Nazarenko, Larissa; Luo, Yunfeng

    2002-09-27

    In recent decades, there has been a tendency toward increased summer floods in south China, increased drought in north China, and moderate cooling in China and India while most of the world has been warming. We used a global climate model to investigate possible aerosol contributions to these trends. We found precipitation and temperature changes in the model that were comparable to those observed if the aerosols included a large proportion of absorbing black carbon ("soot"), similar to observed amounts. Absorbing aerosols heat the air, alter regional atmospheric stability and vertical motions, and affect the large-scale circulation and hydrologic cycle with significant regional climate effects.

  4. A photochemically resistant component in riverine dissolved black carbon

    Science.gov (United States)

    Dittmar, Thorsten; Riedel, Thomas; Niggemann, Jutta; Vähätalo, Anssi

    2015-04-01

    Rivers transport combustion-derived dissolved black carbon (DBC) to the oceans at an annual flux that is much higher than required to balance the oceanic inventory of DBC. To resolve this mismatch we studied the long-term stability of DBC in ten major world rivers that together account for approximately 1/3 of the global freshwater discharge to the oceans. Riverine DBC was remarkably resistant against microbial degradation, but decomposition of nearly all chromophoric dissolved organic matter under extensive irradiation with simulated sunlight removed almost 80% of DBC. Photochemically transformed DBC was further microbially decomposed by more than 10% in a subsequent one-year long bioassay. Based on these findings, on a global scale, the estimated riverine flux of microbially degraded and photo-resistant DBC is sufficient to replenish the oceans with DBC and likely contributes to the dissolved organic matter pool that persists in the oceans and sequesters carbon for centuries to millennia.

  5. Effect of the Purple carbon black on the properties of NR/BR blend

    Science.gov (United States)

    Yanfang, Zhao; Dan, Liu; Shengbo, Lin; Binjian; Yinmei, Zhao; Shuangquan, Liao

    2014-08-01

    Purple black is light colored mineral filler mining in recent years in Hainan. The effect of the dosage of the purple carbon black and purple carbon black modificated by Si69 on the vulcanization characteristics, mechanical properties, thermal stability, the damping performance of NR/BR blend rubber were studied, and the blending adhesive tensile sections were analyzed by SEM. Research showed that, with the increasing dosage of the purple carbon black, vulcanization characteristics of NR/BR blend had a little change. Adding the purple carbon black into blending had a reinforcing effect. when the dosage of the purple carbon black was 20, the mechanical properties of blending adhesive was good; Coupling agent Si69 had a modification effect on the purple carbon black. With increasing dosage of Si69, performance of the rubber was improved initially and then decreased; when the mass fraction of Si69 was 8% of the dosage of the purple carbon black, rubber performance was optimal. Purple carbon black had no obvious effect on thermal stability of the rubber, but it improved the damping rubber temperature and damping factor.

  6. Birchwood biochar as partial carbon black replacement in styrene-butadiene rubber composites

    Science.gov (United States)

    Birchwood feedstock was used to make slow pyrolysis biochar that contained 89% carbon and rubber. Composites made from blended fillers of 25/75 biochar/carbon black were equivalent to or superior to their 100% carbo...

  7. High Black Carbon (BC) Concentrations along Indian National Highways

    Science.gov (United States)

    Kumar, S.; Singh, A. K.; Singh, R. P.

    2015-12-01

    Abstract:Black carbon (BC), the optically absorbing component of carbonaceous aerosol, has direct influence on radiation budget and global warming. Vehicular pollution is one of the main sources for poor air quality and also atmospheric pollution. The number of diesel vehicles has increased on the Indian National Highways during day and night; these vehicles are used for the transport of goods from one city to another city and also used for public transport. A smoke plume from the vehicles is a common feature on the highways. We have made measurements of BC mass concentrations along the Indian National Highways using a potable Aethalometer installed in a moving car. We have carried out measurements along Varanasi to Kanpur (NH-2), Varanasi to Durgapur (NH-2), Varanasi to Singrauli (SH-5A) and Varanasi to Ghazipur (NH-29). We have found high concentration of BC along highways, the average BC mass concentrations vary in the range 20 - 40 µg/m3 and found high BC mass concentrations up to 600 μg/m3. Along the highways high BC concentrations were characteristics of the presence of industrial area, power plants, brick kilns and slow or standing vehicles. The effect of increasing BC concentrations along the National Highways and its impact on the vegetation and human health will be presented. Key Words: Black Carbon; Aethalometer; mass concentration; Indian National Highways.

  8. Oxidation behavior of a kind of carbon black

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The DTG curves of a kind of carbon black during TPO tests were found to have multiple peaks with an unusual sharp peak after the main peak.TPO tests with different sample loads,oxygen fractions and heating rates were carried out to study the influence of the experimental parameters on the sharp peak.The results show that the sharp peak is not caused by heat and mass transfer limitations,but by the intrinsic oxidation kinetics of the carbon black.The evolution of the specific surface area during the intrinsic kinetic controlled oxidation process was then analyzed using isothermal oxidation at low temperatures which showed that the sharp peak is caused by the increase of the specific surface area.The pore structure changes greatly influence the oxidation process when the reaction is controlled by the intrinsic kinetics.When there were no heat and mass transfer limitations,the different oxidation processes result in the same specific surface area evolution.

  9. Changing Export of Dissolved Black Carbon from Arctic Rivers

    Science.gov (United States)

    Stubbins, A.; Spencer, R. G.; Mann, P. J.; Dittmar, T.; Niggemann, J.; Holmes, R. M.; McClelland, J. W.

    2014-12-01

    Arctic rivers carry black carbon (BC) from Arctic soils to the ocean, linking two of the largest carbon stores on Earth. Wildfires have charred biomass since land plants emerged. BC, a refractory component of char, has accumulated in soils. In the oceans, dissolved BC (DBC) has also accumulated. Here we use samples and data collected as part of the long-term, high temporal resolution Arctic Great Rivers Observatory to model export of DBC from the six largest Arctic Rivers. Scaling to the pan-Arctic catchment, we report that ~3 million tons of DBC are delivered to the Arctic Ocean each year, which is ~8% of dissolved organic carbon loads to the Arctic Ocean. We suggest the transfer of Arctic river DBC to areas of deep water formation is a major source of DBC to the deep ocean carbon store. As the Arctic warms, greater wildfire occurrence is expected to produce more BC and changing hydrology and permafrost thaw to promote DBC export. Thus, the transfer of BC from Arctic soils to the ocean is predicted to increase.

  10. An improved method for quantitatively measuring the sequences of total organic carbon and black carbon in marine sediment cores

    Science.gov (United States)

    Xu, Xiaoming; Zhu, Qing; Zhou, Qianzhi; Liu, Jinzhong; Yuan, Jianping; Wang, Jianghai

    2017-04-01

    Understanding global carbon cycle is critical to uncover the mechanisms of global warming and remediate its adverse effects on human activities. Organic carbon in marine sediments is an indispensable part of the global carbon reservoir in global carbon cycling. Evaluating such a reservoir calls for quantitative studies of marine carbon burial, which closely depend on quantifying total organic carbon and black carbon in marine sediment cores and subsequently on obtaining their high-resolution temporal sequences. However, the conventional methods for detecting the contents of total organic carbon or black carbon cannot resolve the following specific difficulties, i.e., (1) a very limited amount of each subsample versus the diverse analytical items, (2) a low and fluctuating recovery rate of total organic carbon or black carbon versus the reproducibility of carbon data, and (3) a large number of subsamples versus the rapid batch measurements. In this work, (i) adopting the customized disposable ceramic crucibles with the micropore-controlled ability, (ii) developing self-made or customized facilities for the procedures of acidification and chemothermal oxidization, and (iii) optimizing procedures and carbon-sulfur analyzer, we have built a novel Wang-Xu-Yuan method (the WXY method) for measuring the contents of total organic carbon or black carbon in marine sediment cores, which includes the procedures of pretreatment, weighing, acidification, chemothermal oxidation and quantification; and can fully meet the requirements of establishing their highresolution temporal sequences, whatever in the recovery, experimental efficiency, accuracy and reliability of the measurements, and homogeneity of samples. In particular, the usage of disposable ceramic crucibles leads to evidently simplify the experimental scenario, which further results in the very high recovery rates for total organic carbon and black carbon. This new technique may provide a significant support for

  11. Photo-lability of deep ocean dissolved black carbon

    Directory of Open Access Journals (Sweden)

    A. Stubbins

    2012-01-01

    Full Text Available Dissolved black carbon (DBC, defined here as condensed aromatics isolated from seawater via PPL solid phase extraction and quantified as benzene polycarboxylic acid oxidation products, is a significant component of the oceanic dissolved organic carbon (DOC pool. These condensed aromatics are widely distributed in the open ocean and appear to be tens of thousands of years old. As such DBC is regarded as highly refractory. In the current study, the photo-lability of DBC, DOC and coloured dissolved organic matter (CDOM; ultraviolet-visible absorbance were determined over the course of a 28 d irradiation of North Atlantic Deep Water under a solar simulator. During the irradiation DBC fell from 1044 ± 164 nM C to 55 ± 15 nM C, a 20-fold decrease in concentration. Dissolved black carbon photo-degradation was more rapid and more extensive than for bulk CDOM and DOC. Further, the photo-lability of components of the DBC pool increased with their degree of aromatic condensation. These trends indicate that a continuum of compounds of varying photo-lability exists within the marine DOC pool. In this continuum, photo-lability scales with aromatic character, specifically the degree of condensation. Scaling the rapid photo-degradation of DBC to rates of DOC photo-mineralisation for the global ocean leads to an estimated photo-chemical half-life for oceanic DBC of less than 800 yr. This is more than an order of magnitude shorter than the apparent age of DBC in the ocean. Photo-degradation is therefore posited as the primary sink for oceanic DBC and the survival of DBC molecules in the oceans for millennia appears to be facilitated not by their inherent inertness but by the rate at which they are cycled through the surface ocean's photic zone.

  12. Plasma Polymerization Surface Modification of Carbon Black and its Effect in Elastomers

    NARCIS (Netherlands)

    Mathew, T.; Datta, R.N.; Dierkes, W.K.; Talma, A.G.; Ooij, van W.J.; Noordermeer, J.W.M.

    2011-01-01

    Surface modification of carbon black by plasma polymerization was aimed to reduce its surface energy in order to compatibilize the filler with various elastomers. A fullerenic carbon black was used for the modification process. Thermogravimetric analysis, wetting behavior with liquids of known surfa

  13. Sources of uncertainties in modelling black carbon at the global scale

    NARCIS (Netherlands)

    Vignati, E.; Karl, M.; Krol, M.C.; Wilson, J.; Stier, P.; Cavalli, F.

    2010-01-01

    Our understanding of the global black carbon (BC) cycle is essentially qualitative due to uncertainties in our knowledge of its properties. This work investigates two source of uncertainties in modelling black carbon: those due to the use of different schemes for BC ageing and its removal rate in th

  14. Sources of uncertainties in modelling black carbon at the global scale

    NARCIS (Netherlands)

    Vignati, E.; Karl, M.; Krol, M.C.; Wilson, J.; Stier, P.; Cavalli, F.

    2010-01-01

    Our understanding of the global black carbon (BC) cycle is essentially qualitative due to uncertainties in our knowledge of its properties. This work investigates two source of uncertainties in modelling black carbon: those due to the use of different schemes for BC ageing and its removal rate in

  15. Carbon black nanoparticle instillation induces sustained inflammation and genotoxicity in mouse lung and liver

    DEFF Research Database (Denmark)

    Bourdon, Julie A; Saber, Anne T; Jacobsen, Nicklas R;

    2012-01-01

    Widespread occupational exposure to carbon black nanoparticles (CBNPs) raises concerns over their safety. CBNPs are genotoxic in vitro but less is known about their genotoxicity in various organs in vivo.......Widespread occupational exposure to carbon black nanoparticles (CBNPs) raises concerns over their safety. CBNPs are genotoxic in vitro but less is known about their genotoxicity in various organs in vivo....

  16. Climate Response due to Black Carbon Aerosols and Black-Carbon-induced SST Effects in MIROC5.0

    Science.gov (United States)

    Yu, Y.; Nakajima, T.; Goto, D.

    2014-12-01

    This study used the Models for Interdisciplinary Research on Climate, MIROC5.0, one member of the Coupled Model Intercomparison Project (CMIP5), to investigate the effects of black carbon (BC) aerosols on atmospheric circulations and climate including intricate feedback mechanism. The simulations with and without BC were conducted and the difference between these two runs is the corresponding response due to BC. Both atmosphere-ocean coupled general circulation model simulation (CGCM with full ocean) and the fixed SST runs (AGCM with prescribed sea surface temperature and sea ice temperature) were used to study the effects from ocean boundary conditions. The regional effects due to BC may be much larger than models have assumed (Andreae and Ramanathan, 2013; Bond et al., 2013). There are many studies used simplified mixed-layer ocean under prescribed surface heat flux to estimate the climate effect of BC (Kim et al., 2014), however these ocean-atmosphere coupled processes act on seasonal and annual time scales more real than non-ocean-atmosphere coupled models. Our results showed that the comprehensively sea-air interaction amplified the heating effect of black carbon aerosols; the presence of BC affected climate not only at local source areas but also at remote regions due to changes on energy transport processes and atmospheric circulations; we also discussed how the feedback of SST induced by BC affected on the distribution and magnitudes of climate response such as temperature, precipitation and cloud coverage between CGCM and AGCM runs.

  17. Is marine dissolved organic matter the "missing sink" for soil-derived black carbon?

    Science.gov (United States)

    Dittmar, Thorsten; Suryaputra, I. Gusti N. A.; Niggemann, Jutta

    2010-05-01

    The thermal alteration of biomass during wildfires can be an important factor for the stabilization of organic matter in soils. Black carbon, i.e. biochars and soot, is more resistant to biodegradation than unaltered biomass, and it can therefore accumulate in soils and sediments. Our knowledge on the turnover of black carbon is still very fragmentary, and the known loss rates do not account for the estimated production rates. Major loss mechanisms remain unidentified or have been underestimated. Recently, we have identified a major thermogenic component in dissolved organic matter (DOM) of the deep ocean. We hypothesize that black carbon in soils is solubilized over time, probably via microbial interaction, and transported via rivers into the ocean. DOM, one of the largest organic carbon pools on earth, could therefore be an important transport medium of soil-derived black carbon. A case study was performed in the Suwannee River estuary and adjacent oceanic shelf (Florida, USA). The Suwannee River drains extensive wetlands and fire-impacted forests. The fate of dissolved black carbon was traced from the river through its estuary into the open Gulf of Mexico. Black carbon was molecularly quantified as benzenepolycarboxylic acids after nitric acid oxidation via a new UPLC method (ultra-performance liquid chromatography). The molecular analysis was accompanied by optical (excitation-emission matrix fluorescence and absorbance spectroscopy) and elemental characterization of DOM. A major component (approx. 10% on a carbon basis) of Suwannee River DOM could be identified as black carbon. The concentration of black carbon decreased offshore, and on the open ocean only about 1% of DOM could be identified as black carbon. In the deep ocean, the thermogenic component of DOM is higher and approx. 2.4% of DOM. The surface ocean must therefore be an efficient sink for dissolved black carbon. We hypothesize that sunlight may initiate photochemical reactions that cause a loss of

  18. The mass function of nearby black hole candidates

    CERN Document Server

    Caramete, Laurentiu I

    2009-01-01

    The mass function of super-massive black holes in our cosmic neighborhood is required to understand the statistics of activity, specifically the production of ultra high energy particles. We determine a mass function of black hole candidates from the entire sky outside the Galactic plane. Using the 2MASS catalogue as a starting point, and the well established correlation between black hole mass and the old bulge population of stars, we derive a list of nearby black hole candidates within the redshift range z 10^7 M_sol has 5,634 entries. Here we use this catalogue to derive the mass function. We correct for volume, so that this mass function is a volume limited distribution to redshift 0.025. The mass function of nearby black hole candidates is a straight simple power-law, extending down into the mass range, where nuclear star clusters may replace the super-massive black holes. The slope of this mass function can be explained in a simple merger picture. Integrating this mass function over the redshift range,...

  19. Influence of carbon black and indium tin oxide absorber particles on laser transmission welding

    Science.gov (United States)

    Aden, Mirko; Mamuschkin, Viktor; Olowinsky, Alexander

    2015-06-01

    For laser transmission welding of polypropylene carbon black and indium tin oxide (ITO) are used as absorber particles. Additionally, the colorant titanium dioxide is mixed to the absorbing part, while the transparent part is kept in natural state. The absorption coefficients of ITO and carbon black particles are obtained, as well as the scattering properties of polypropylene loaded with titanium dioxide (TiO2). At similar concentrations the absorption coefficient of ITO is an order of magnitude smaller than that of carbon black. Simulations of radiation propagation show that the penetration depth of laser light is smaller for carbon black. Therefore, the density of the released heat is higher. Adding TiO2 changes the distribution of heat in case of ITO, whereas for carbon black the effect is negligible. Thermal simulations reveal the influence of the two absorbers and TiO2 on the heat affected zone. The results of the thermal simulations are compared to tensile test results.

  20. Towards Soil and Sediment Inventories of Black Carbon

    Science.gov (United States)

    Masiello, C. A.

    2008-12-01

    A body of literature on black carbon (BC) concentrations in soils and sediments is rapidly accumulating, but as of yet, there are no global or regional inventories of BC in either reservoir. Soil and sediment BC inventories are badly needed for a range of fields. For example, in oceanography a global sediment BC inventory is crucial in understanding the role of biomass burning in the development of stable marine carbon reservoirs, including dissolved organic carbon and sedimentary organic carbon. Again in the marine environment, BC likely strongly impacts the fate and transport of anthropogenic pollutants: regional inventories of BC in sediments will help develop better environmental remediation strategies. In terrestrial systems well-constrained natural BC soil inventories would help refine ecological, agricultural, and soil biogeochemical studies. BC is highly sorptive of nutrients including nitrogen and phosphorous. The presence of BC in ecosystems almost certainly alters N and P cycling; however, without soil BC inventories, we cannot know where BC has a significant impact. BC's nutrient sorptivity and water-holding capacity make it an important component of agricultural soils, and some researchers have proposed artificially increasing soil BC inventories to improve soil fertility. Natural soil BC concentrations in some regions are quite high, but without a baseline inventory, it is challenging to predict when agricultural amendment will significantly exceed natural conditions. And finally, because BC is one of the most stable fractions of organic carbon in soils, understanding its concentration and regional distribution will help us track the dynamics of soil organic matter response to changing environmental conditions. Developing effective regional and global BC inventories is challenging both because of data sparsity and methodological intercomparison issues. In this presentation I will describe a roadmap to generating these valuable inventories.

  1. Light Absorption in Arctic Sea Ice - Black Carbon vs Chlorophyll

    Science.gov (United States)

    Ogunro, O. O.; Wingenter, O. W.; Elliott, S.; Hunke, E. C.; Flanner, M.; Wang, H.; Dubey, M. K.; Jeffery, N.

    2015-12-01

    The fingerprint of climate change is more obvious in the Arctic than any other place on Earth. This is not only because the surface temperature there has increased at twice the rate of global mean temperature but also because Arctic sea ice extent has reached a record low of 49% reduction relative to the 1979-2000 climatology. Radiation absorption through black carbon (BC) deposited on Arctic snow and sea ice surface is one of the major hypothesized contributors to the decline. However, we note that chlorophyll-a absorption owing to increasing biology activity in this region could be a major competitor during boreal spring. Modeling of sea-ice physical and biological processes together with experiments and field observations promise rapid progress in the quality of Arctic ice predictions. Here we develop a dynamic ice system module to investigate discrete absorption of both BC and chlorophyll in the Arctic, using BC deposition fields from version 5 of Community Atmosphere Model (CAM5) and vertically distributed layers of chlorophyll concentrations from Sea Ice Model (CICE). To this point, our black carbon mixing ratios compare well with available in situ data. Both results are in the same order of magnitude. Estimates from our calculations show that sea ice and snow around the Canadian Arctic Archipelago and Baffin Bay has the least black carbon absorption while values at the ice-ocean perimeter in the region of the Barents Sea peak significantly. With regard to pigment concentrations, high amounts of chlorophyll are produced in Arctic sea ice by the bottom microbial community, and also within the columnar pack wherever substantial biological activity takes place in the presence of moderate light. We show that the percentage of photons absorbed by chlorophyll in the spring is comparable to the amount attributed to BC, especially in areas where the total deposition rates are decreasing with time on interannual timescale. We expect a continuous increase in

  2. Black Carbon in Marine Dissolved Organic Carbon: Abundance and Radiocarbon Measurements in the Global Ocean

    Science.gov (United States)

    Coppola, A. I.; Walker, B. D.; Druffel, E. R. M.

    2014-12-01

    Compound specific radiocarbon analysis is a powerful tool for understanding the cycling of individual components, such as black carbon (BC) produced from biomass burning and fossil fuel combustion, within bulk pools, like the marine dissolved organic carbon pool. Here, we use a solid phase extraction method and a wide range of solvent polarities to concentrate dissolved organic carbon from seawater. Then we isolate BC in sufficient quantities for radiocarbon analysis. We report the radiocarbon age of BC, concentrations and its relative structure, from coastal and open ocean surface samples. We will discuss our progress towards measuring these quantities in dissolved organic carbon collected from the Pacific and Atlantic oceans to understand the fate, transformation and cycling of BC in the world ocean. These measurements are paired with bulk DOC Δ14C profiles, providing insight into the role of BC as a missing sink in the ultra-refractory DOC pool.

  3. Analysis of the Thermal Conductivity of Polymer Nanocomposites Filled with Carbon Nanotubes and Carbon Black

    Directory of Open Access Journals (Sweden)

    R.V. Dinzhos

    2014-04-01

    Full Text Available Experimental results and theoretical studies of thermophysical characteristics crystalline polyethylene nanocomposites containing from 0.3 to 2.5 wt. % carbon black and nanocomposites containing from 0.2 to 1.5 wt. % carbon nanotubes is done in the article. The fundamentals of the effective medium theory and percolation theory and how they correlate with the experimental data is shown. The features of the structure’s influence of polymer composites on their thermal properties is studied. A comparative analysis of the thermal conductivity of the compositions according to the geometry of the filler is done.

  4. Near-edge X-ray absorption fine structure (NEXAFS) spectroscopy for mapping nano-scale distribution of organic carbon forms in soil: Application to black carbon particles

    Science.gov (United States)

    Lehmann, Johannes; Liang, Biqing; Solomon, Dawit; Lerotic, Mirna; LuizãO, Flavio; Kinyangi, James; SchäFer, Thorsten; Wirick, Sue; Jacobsen, Chris

    2005-03-01

    Small-scale heterogeneity of organic carbon (C) forms in soils is poorly quantified since appropriate analytical techniques were not available up to now. Specifically, tools for the identification of functional groups on the surface of micrometer-sized black C particles were not available up to now. Scanning Transmission X-ray Microscopy (STXM) using synchrotron radiation was used in conjunction with Near-Edge X-ray Absorption Fine Structure (NEXAFS) spectroscopy to investigate nano-scale distribution (50-nm resolution) of C forms in black C particles and compared to synchrotron-based FTIR spectroscopy. A new embedding technique was developed that did not build on a C-based embedding medium and did not pose the risk of heat damage to the sample. Elemental sulfur (S) was melted to 220°C until it polymerized and quenched with liquid N2 to obtain a very viscous plastic S in which the black C could be embedded until it hardened to a noncrystalline state and was ultrasectioned. Principal component and cluster analysis followed by singular value decomposition was able to resolve distinct areas in a black carbon particle. The core of the studied biomass-derived black C particles was highly aromatic even after thousands of years of exposure in soil and resembled the spectral characteristics of fresh charcoal. Surrounding this core and on the surface of the black C particle, however, much larger proportions of carboxylic and phenolic C forms were identified that were spatially and structurally distinct from the core of the particle. Cluster analysis provided evidence for both oxidation of the black C particle itself as well as adsorption of non-black C. NEXAFS spectroscopy has great potential to allow new insight into black C properties with important implications for biogeochemical cycles such as mineralization of black C in soils and sediments, and adsorption of C, nutrients, and pollutants as well as transport in the geosphere, hydrosphere, and atmosphere.

  5. Brief Analysis on the Production & Operation Situation of Chinese Carbon Black Industry in the First Half Year

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    At present, there are about 120 carbon black manufacturing enterprises in China with the production capacity of 3.41 million tons, accounting for 78% of the total production capacity of the country, in which there are 31 carbon black enterprises with the production capacity of over 50,000 tons. Compared with the international carbon black industry, our carbon black industry has a low intensification.

  6. Black Carbon Vertical Profiles Strongly Affect Its Radiative Forcing Uncertainty

    Science.gov (United States)

    Samset, B. H.; Myhre, G.; Schulz, M.; Balkanski, Y.; Bauer, S.; Berntsen, T. K.; Bian, H.; Bellouin, N.; Diehl, T.; Easter, R. C.; Ghan, S. J.; Iversen, T.; Kinne, S.; Kirkevag, A.; Lamarque, J.-F.; Lin, G.; Liu, X.; Penner, J. E.; Seland, O.; Skeie, R. B.; Stier, P.; Takemura, T.; Tsigaridis, K.; Zhang, K.

    2013-01-01

    The impact of black carbon (BC) aerosols on the global radiation balance is not well constrained. Here twelve global aerosol models are used to show that at least 20% of the present uncertainty in modeled BC direct radiative forcing (RF) is due to diversity in the simulated vertical profile of BC mass. Results are from phases 1 and 2 of the global aerosol model intercomparison project (AeroCom). Additionally, a significant fraction of the variability is shown to come from high altitudes, as, globally, more than 40% of the total BC RF is exerted above 5 km. BC emission regions and areas with transported BC are found to have differing characteristics. These insights into the importance of the vertical profile of BC lead us to suggest that observational studies are needed to better characterize the global distribution of BC, including in the upper troposphere.

  7. Optical Properties of Small Ice Crystals with Black Carbon Inclusions

    Science.gov (United States)

    Yang, X.; Geier, M.; Arienti, M.

    2013-12-01

    The optical properties of ice crystals play a fundamental role in modeling atmospheric radiation and hydrological cycle, which are critical in monitoring climate change. While Black Carbon (BC) is recognized as the dominant absorber with positive radiative forcing (warming) (Ramanathan & Carmichael, 2008), in-situ observations (Cappa, et al, 2012) indicate that the characterization of the mixing state of BC with ice crystals and other non-BC particles in global climate models (Ghan & Schwartz, 2007) needs further investigation. The limitation in the available mixing models is due to the drastically different absorbing properties of BC compared to other aerosols. We explore the scattering properties of ice crystals (in shapes commonly found in cirrus clouds and contrails - Yang, et al. 2012) with the inclusion of BC particles. The Discrete Dipole Approximation (DDA) (Yurkin & Hoekstra, 2011) is utilized to directly calculate the optical properties of the crystals with multiple BC inclusions, modeled as a distribution of spheres. The results are then compared with the most popular models of internal and external mixing (Liou, et al. 2011). The DDA calculations are carried out over a broad range of BC particle sizes and volume fractions within the crystal at the 532 nm wavelength and for ice crystals smaller than 50 μm. The computationally intensive database generated in this study is critical for understanding the effect of different types of BC inclusions on the atmosphere radiative forcing. Examples will be discussed to illustrate the modification of BC optical properties by encapsulation in ice crystals and how the parameterization of the BC mixing state in global climate models can be improved. Acknowledgements Support by Sandia National Laboratories' LDRD (Laboratory Directed Research and Development) is gratefully acknowledged. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of

  8. Black carbon aerosol-induced Northern Hemisphere tropical expansion

    Science.gov (United States)

    Kovilakam, Mahesh; Mahajan, Salil

    2015-06-01

    Global climate models (GCMs) underestimate the observed trend in tropical expansion. Recent studies partly attribute it to black carbon (BC) aerosols, which are poorly represented in GCMs. We conduct a suite of idealized experiments with the Community Atmosphere Model version 4 coupled to a slab ocean model forced with increasing BC concentrations covering a large swath of the estimated range of current BC radiative forcing while maintaining their spatial distribution. The Northern Hemisphere (NH) tropics expand poleward nearly linearly as BC radiative forcing increases (0.7° W-1 m2), indicating that a realistic representation of BC could reduce GCM biases. We find support for the mechanism where BC-induced midlatitude tropospheric heating shifts the maximum meridional tropospheric temperature gradient poleward resulting in tropical expansion. We also find that the NH poleward tropical edge is nearly linearly correlated with the location of the Intertropical Convergence Zone, which shifts northward in response to increasing BC.

  9. Electrical properties of foamed polypropylene/carbon black composites

    Science.gov (United States)

    Iliev, M.; Kotzev, G.; Vulchev, V.

    2016-02-01

    Polypropylene composites containing carbon black fillers were produced by vibration assisted extrusion process. Solid (unfoamed) composite samples were molded by conventional injection molding method, while structural foams were molded by a low pressure process. The foamed samples were evidenced to have a solid skin-foamed core structure which main parameters were found to depend on the quantity of material injected in the mold. The average bubbles' sizes and their distribution were investigated by scanning electron microscopy. It is established that the conductivity of the foamed samples gradually decreases when reducing the sample density. Nevertheless, the conductivity is found to be lower than the conductivity of the unfoamed samples both being of the same order. The flexural properties of the composites were studied and the results were discussed in the context of the structure parameters of the foamed samples.

  10. Functionalized carbon nanotubes: biomedical applications

    Directory of Open Access Journals (Sweden)

    Vardharajula S

    2012-10-01

    Full Text Available Sandhya Vardharajula,1 Sk Z Ali,2 Pooja M Tiwari,1 Erdal Eroğlu,1 Komal Vig,1 Vida A Dennis,1 Shree R Singh11Center for NanoBiotechnology and Life Sciences Research, Alabama State University, Montgomery, AL, USA; 2Department of Microbiology, Osmania University, Hyderabad, IndiaAbstract: Carbon nanotubes (CNTs are emerging as novel nanomaterials for various biomedical applications. CNTs can be used to deliver a variety of therapeutic agents, including biomolecules, to the target disease sites. In addition, their unparalleled optical and electrical properties make them excellent candidates for bioimaging and other biomedical applications. However, the high cytotoxicity of CNTs limits their use in humans and many biological systems. The biocompatibility and low cytotoxicity of CNTs are attributed to size, dose, duration, testing systems, and surface functionalization. The functionalization of CNTs improves their solubility and biocompatibility and alters their cellular interaction pathways, resulting in much-reduced cytotoxic effects. Functionalized CNTs are promising novel materials for a variety of biomedical applications. These potential applications are particularly enhanced by their ability to penetrate biological membranes with relatively low cytotoxicity. This review is directed towards the overview of CNTs and their functionalization for biomedical applications with minimal cytotoxicity.Keywords: carbon nanotubes, cytotoxicity, functionalization, biomedical applications

  11. Sources of uncertainties in modelling Black Carbon at the global scale

    Directory of Open Access Journals (Sweden)

    F. Cavalli

    2009-11-01

    Full Text Available Our understanding of the global black carbon cycle is essentially qualitative due to uncertainties in our knowledge of the properties of black carbon. This work investigates uncertainties related to modelling black carbon: due to the use of different schemes for BC ageing and its removal rate in the global Transport-Chemistry model TM5 and due to the uncertainties in the definition and quantification of observed black carbon, which propagate through to both the emission inventories, and the measurements used for the model evaluation.

    The schemes for the atmospheric processing of black carbon that have been tested with the model are (i a simple approach considering black carbon as bulk aerosol and a simple treatment in the removal and (ii a more complete description of microphysical aging within an aerosol dynamics model, where removal is coupled to the microphysical properties of the aerosol. In the first approach a fixed 70% of black carbon is scavenged in clouds and removed when rain is present. The second leads to a global average of 40% black carbon that is scavenged in clouds and subsequently removed by rain, thus resulting in a longer lifetime. This difference is reflected in comparisons between both sets of modelled results and the measurements. Close to the sources, both anthropogenic and vegetation fire source regions, the model results do not differ significantly, showing that the emissions are the prevailing mechanism determining the concentrations and the choice of the aerosol scheme does not influence the levels. In more remote areas such as oceanic and polar regions the differences can be orders of magnitude, due to the differences between the two schemes. The more complete description reproduces the seasonal trend of the black carbon observations in those areas, although not always the magnitude of the signal, while the more simplified approach underestimates black carbon concentrations by orders of magnitude.

  12. Adsorption ability of the carbon black for nickel ions uptake from aqueous solution

    Directory of Open Access Journals (Sweden)

    Rađenović Ankica

    2013-01-01

    Full Text Available Surface modification can be performed by adsorption of certain organic compounds on the surface of carbon. The main objective of this work was to compare the adsorption ability of acid-modified carbon black with the non-modified one. Modification process was performed by adsorption of acetic acid onto commercial carbon black surface. A batch adsorption system was applied to study the both adsorption reaction, acetic acid and Ni(II adsorption onto the carbon black. Adsorption isotherms of acetic acid and Ni(II adsorption onto the non-modified and modified carbon black were fitted by classical adsorption models, such as Freundlich and Langmuir models. Modified carbon black surface become more active for Ni(II ions removal from aqueous solutions. The results showed that modification by acetic acid increases the adsorption capacity of carbon black from 18.3823 mg Ni(II g-1 to 86.9566 mg Ni(II g-1. SEM analysis enabled the observation of any surface changes in the carbon black that have occurred due to either acid modification or Ni(II adsorption.

  13. Characterization of black carbon in the ambient air of Agra, India: Seasonal variation and meteorological influence

    Science.gov (United States)

    Gupta, Pratima; Singh, Shalendra Pratap; Jangid, Ashok; Kumar, Ranjit

    2017-09-01

    This study characterizes the black carbon in Agra, India home to the Taj Mahal—and situated in the Indo-Gangetic basin. The mean black carbon concentration is 9.5 μg m-3 and, owing to excessive biomass/fossil fuel combustion and automobile emissions, the concentration varies considerably. Seasonally, the black carbon mass concentration is highest in winter, probably due to the increased fossil fuel consumption for heating and cooking, apart from a low boundary layer. The nocturnal peak rises prominently in winter, when the use of domestic heating is excessive. Meanwhile, the concentration is lowest during the monsoon season because of the turbulent atmospheric conditions and the process of washout by precipitation. The ratio of black carbon to brown carbon is less than unity during the entire study period, except in winter (December). This may be because that biomass combustion and diesel exhaust are major black carbon contributors in this region, while a higher ratio in winter may be due to the increased consumption of fossil fuel and wood for heating purposes. ANOVA reveals significant monthly variation in the concentration of black carbon; plus, it is negatively correlated with wind speed and temperature. A high black carbon mass concentration is observed at moderate (1-2 m s-1) wind speed, as compared to calm or turbulent atmospheric conditions.

  14. Fluxes of soot black carbon to South Atlantic sediments

    Science.gov (United States)

    Lohmann, Rainer; Bollinger, Kevyn; Cantwell, Mark; Feichter, Johann; Fischer-Bruns, Irene; Zabel, Matthias

    2009-03-01

    Deep sea sediment samples from the South Atlantic Ocean were analyzed for soot black carbon (BC), total organic carbon (TOC), stable carbon isotope ratios (δ13C), and polycyclic aromatic hydrocarbons (PAHs). Soot BC was present at low concentrations (0.04-0.17% dry weight), but accounted for 3-35% of TOC. Fluxes of soot BC were calculated on the basis of known sedimentation rates and ranged from 0.5 to 7.8 μg cm-2 a-1, with higher fluxes near Africa compared to South America. Values of δ13C indicated a marine origin for the organic carbon but terrestrial sources for the soot BC. PAH ratios implied a pyrogenic origin for most samples and possibly a predominance of traffic emissions over wood burning off the African coast. A coupled ocean-atmosphere-aerosol-climate model was used to determine fluxes of BC from 1860 to 2000 to the South Atlantic. Model simulation and measurements both yielded higher soot BC fluxes off the African coast and lower fluxes off the South American coast; however, measured sedimentary soot BC fluxes exceeded simulated values by ˜1 μg cm-2 a-1 on average (within a factor of 2-4). For the sediments off the African coast, soot BC delivery from the Congo River could possibly explain the higher flux rates, but no elevated soot BC fluxes were detected in the Amazon River basin. In total, fluxes of soot BC to the South Atlantic were ˜480-700 Gg a-1 in deep sea sediments. Our results suggest that attempts to construct a global mass balance of BC should include estimates of the atmospheric deposition of BC.

  15. Observation of black carbon, ozone and carbon monoxide in the Kali Gandaki Valley Nepal

    Science.gov (United States)

    Dhungel, S.; Panday, A. K.; Kathayat, B.

    2014-12-01

    The increased melting of snow and ice in the arctic and the Himalaya is a growing concern for all of the earth's population. Deposition of black carbon (BC) on the snow and ice surface accelerates melting by absorbing the radiative energy and directly transferring all that energy onto the underlying surface. During pre-monsoon season, satellite images show a thick layer of haze covering the Indo-Gangetic plain (IGP) and the Himalayan foothills. Sub-micron particles are transported to the Himalaya from the IGP predominantly driven by the thermal valley wind system. The Himalayas consist of some of the tallest mountain ranges in the world, over 8000m tall that reach the stratosphere. The Kali Gandaki Valley in Nepal is one of the deepest gorges in the world, and has some of the highest up-valley winds in the world. It is also one of the most open connecting points for air from IGP to reach the Tibetan Plateau. In 2010 the University of Virginia, in collaboration with ICIMOD and Nepal Wireless, established an atmospheric research station in Jomsom, Nepal (28.78N, 83.42E, 2900 m.a.s.l.) half-way along the Kali Gandaki valley. The station is equipped to measure black carbon (BC), carbon monoxide (CO), and ozone concentrations. It also has an automated weather station, a filter sampler, and a NASA Aeronet Sunphotometer. Here we present our observations of black carbon, ozone, carbon monoxide at Jomsom to show the diurnal and seasonal variability of the pollutants. The results show diurnal patterns in the concentration of these pollutants and also episodes of high pollutant transport along the valley. These transport episodes are more common during the pre-monsoon season which indicates that deep mountain valleys like the Kali Gandaki valley facilitate the transport of pollutants and thus promote snow and glacial melting.

  16. Functionalized carbon nanotubes: biomedical applications.

    Science.gov (United States)

    Vardharajula, Sandhya; Ali, Sk Z; Tiwari, Pooja M; Eroğlu, Erdal; Vig, Komal; Dennis, Vida A; Singh, Shree R

    2012-01-01

    Carbon nanotubes (CNTs) are emerging as novel nanomaterials for various biomedical applications. CNTs can be used to deliver a variety of therapeutic agents, including biomolecules, to the target disease sites. In addition, their unparalleled optical and electrical properties make them excellent candidates for bioimaging and other biomedical applications. However, the high cytotoxicity of CNTs limits their use in humans and many biological systems. The biocompatibility and low cytotoxicity of CNTs are attributed to size, dose, duration, testing systems, and surface functionalization. The functionalization of CNTs improves their solubility and biocompatibility and alters their cellular interaction pathways, resulting in much-reduced cytotoxic effects. Functionalized CNTs are promising novel materials for a variety of biomedical applications. These potential applications are particularly enhanced by their ability to penetrate biological membranes with relatively low cytotoxicity. This review is directed towards the overview of CNTs and their functionalization for biomedical applications with minimal cytotoxicity.

  17. Physico-mechanical and electrical properties of conductive carbon black reinforced chlorosulfonated polyethylene vulcanizates

    Directory of Open Access Journals (Sweden)

    2008-12-01

    Full Text Available The present work deals with the effect of conductive carbon black (Ensaco 350G on the physico-mechanical and electrical properties of chlorosulfonated polyethylene (CSM rubber vulcanizates. The physico-mechanical properties like tensile strength, tear strength, elongation at break, compression set, hardness and abrasion resistance have been studied before and after heat ageing. Up to 30 parts per hundred rubber (phr filler loading both tensile and tear strength increases beyond which it shows a decreasing trend whereas modulus gradually increases with the filler loading. Incorporation of carbon black increases the hysteresis loss of filled vulcanizates compared to gum vulcanizates. Unlike gum vulcanizate, in filled vulcanizates the rate of relaxation shows increasing trend. The bound rubber content is found to increase with increase in filler loading. Dielectric relaxation spectra were used to study the relaxation behavior as a function of frequency (100 to 106 Hz at room temperature. Variation in real and imaginary parts of electric modulus has been explained on the basis of interfacial polarization of fillers in the polymer medium. The percolation limit of the conductive black as studied by ac conductivity measurements has also been reported.

  18. Carbon black dispersion pre-plating technology for printed wire board manufacturing. Final technology evaluation report

    Energy Technology Data Exchange (ETDEWEB)

    Folsom, D.W.; Gavaskar, A.R.; Jones, J.A.; Olfenbuttel, R.F.

    1993-10-01

    The project compared chemical use, waste generation, cost, and product quality between electroless copper and carbon-black-based preplating technologies at the printed wire board (PWB) manufacturing facility of McCurdy Circuits in Orange, CA. The carbon-black based preplating technology evaluated is used as an alternative process for electroless copper (EC) plating of through-holes before electrolytic copper plating. The specific process used at McCurdy is the BlackHole (BH) technology process, which uses a dispersion of carbon black in an aqueous solution to provide a conductive surface for subsequent electrolytic copper plating. The carbon-black dispersion technology provided effective waste reduction and long-term cost savings. The economic analysis determined that the new process was cost efficient because chemical use was reduced and the process proved more efficient; the payback period was less than 4 yrs.

  19. Black carbon emissions in Russia: A critical review

    Science.gov (United States)

    Evans, Meredydd; Kholod, Nazar; Kuklinski, Teresa; Denysenko, Artur; Smith, Steven J.; Staniszewski, Aaron; Hao, Wei Min; Liu, Liang; Bond, Tami C.

    2017-08-01

    This study presents a comprehensive review of estimated black carbon (BC) emissions in Russia from a range of studies. Russia has an important role regarding BC emissions given the extent of its territory above the Arctic Circle, where BC emissions have a particularly pronounced effect on the climate. We assess underlying methodologies and data sources for each major emissions source based on their level of detail, accuracy and extent to which they represent current conditions. We then present reference values for each major emissions source. In the case of flaring, the study presents new estimates drawing on data on Russia's associated petroleum gas and the most recent satellite data on flaring. We also present estimates of organic carbon (OC) for each source, either based on the reference studies or from our own calculations. In addition, the study provides uncertainty estimates for each source. Total BC emissions are estimated at 688 Gg in 2014, with an uncertainty range 401 Gg-1453 Gg, while OC emissions are 9224 Gg with uncertainty ranging between 5596 Gg and 14,736 Gg. Wildfires dominated and contributed about 83% of the total BC emissions: however, the effect on radiative forcing is mitigated in part by OC emissions. We also present an adjusted estimate of Arctic forcing from Russia's BC and OC emissions. In recent years, Russia has pursued policies to reduce flaring and limit particulate emissions from on-road transport, both of which appear to significantly contribute to the lower emissions and forcing values found in this study.

  20. Dissolved Black Carbon in the South China Sea

    Science.gov (United States)

    Fang, Z.; Yang, W.; Chen, M.; Ma, H.

    2015-12-01

    Dissolved black carbon (DBC) has been ubiquitously reported in dissolved organic matter (DOM). However, the abundance and provenance of DBC in the ocean are not well understood. Here, DBC in the South China Sea (SCS) was determined at molecular level using the benzenepolycarboxylic acids (BPCAs) method. DBC showed high concentrations in the upper 100 m seawater with the average of 1.13 μmol l-1 (n=55). In the intermediate seawater (200-1500 m), DBC ranged from 0.67 to 0.89 μmol l-1 with the average of 0.78 μmol l-1 (n=9), exhibiting nearly homogeneous distributions. The vertical distribution pattern indicated that DBC significantly degraded in the photic zone, corresponding to an attenuate constant of 12.5±4.9 km-1. The ratios of B6CA/B3CAs increased downward, implying that aromatic condensation degree of DBC increase during transport from surface to deep water. Using the standing crops of DBC in the upper 200 m and the residence time of seawater, atmospheric deposition of DBC was estimated to be 1.94 TgC yr-1, accounting for around 16% of the global BC deposition. Our study highlights that DBC could be an important component of ocean carbon cycling in Pacific Asia Marginal Seas.

  1. Black carbon emissions in Russia: A critical review

    Energy Technology Data Exchange (ETDEWEB)

    Evans, Meredydd; Kholod, Nazar; Kuklinski, Teresa; Denysenko, Artur; Smith, Steven J.; Staniszewski, Aaron; Hao, Wei Min; Liu, Liang; Bond, Tami C.

    2017-08-01

    Russia has a particularly important role regarding black carbon (BC) emissions given the extent of its territory above the Arctic Circle, where BC emissions have a particularly pronounced effect on the climate. This study presents a comprehensive review of BC estimates from a range of studies. We assess underlying methodologies and data sources for each major emissions source based on their level of detail, accuracy and extent to which they represent current conditions. We then present reference values for each major emissions source. In the case of flaring, the study presents new estimates drawing on data on Russian associated petroleum gas and the most recent satellite data on flaring. We also present estimates of organic carbon (OC) for each source, either based on the reference studies or from our own calculations. In addition, the study provides uncertainty estimates for each source. Total BC emissions are estimated at 689 Gg in 2014, with an uncertainty range between (407-1,416), while OC emissions are 9,228 Gg (with uncertainty between 5,595 and 14,728). Wildfires dominated and contributed about 83% of the total BC emissions, however the effect on radiative forcing is mitigated by OC emissions. We also present an adjusted estimate of Arctic forcing from Russian OC and BC emissions. In recent years, Russia has pursued policies to reduce flaring and limit particulate emissions from on-road transport, both of which appear to significantly contribute to the lower emissions and forcing values found in this study.

  2. Green Functions and Thermal Nature of Black Holes

    CERN Document Server

    Mijic, M B

    1993-01-01

    There are several ways to establish and study thermal properties of black holes. I review here method of Fulling and Ruijsenaars, based on the analytic structure of Green functions on the complex plane. This method provides a clear distinction between zero and finite temperature field theories, and allows for quick evaluation of black hole temperature. (Lectures presented at the Danube Workshop '93, June 1993, Belgrade, Yugoslavia.)

  3. Structure aggregation of carbon black in ethylene-propylene diene polymer

    Directory of Open Access Journals (Sweden)

    2009-03-01

    Full Text Available The modulus of filled and unfilled Ethylene-propylene diene rubber (EPDM vulcanizates was used to predict the shape-factor of carbon black aggregation in the polymer. Four types of carbon black that vary in particle size and structure were used in this study. Quadratic curves relating the carbon black volume concentration and the modulus ratio of filled and unfilled rubber vulcanizates were used to adopt the shape factor of certain carbon black type. The shape factor of MT, HAF, SRF and Lampblack were 3, 3.75, 4 and 4.25 respectively. X-ray diffraction technique (XRD was also used to evaluate the relative size of crystallite on the filler surface to that of the rubber and correlating it to the shape factor of carbon black aggregation in the polymer. Effect of the pH values and structure of carbon blacks used on the shape factor of filler aggregates were also studied. It was found that the shape factor is independent on the particle size while it is dependent on the pH value and structure of carbon black. Also the crystallites size of the filler is proportional to the shape factor.

  4. Photo-lability of deep ocean dissolved black carbon

    Directory of Open Access Journals (Sweden)

    A. Stubbins

    2012-05-01

    Full Text Available Dissolved black carbon (DBC, defined here as condensed aromatics isolated from seawater via PPL solid phase extraction and quantified as benzenepolycarboxylic acid (BPCA oxidation products, is a significant component of the oceanic dissolved organic carbon (DOC pool. These condensed aromatics are widely distributed in the open ocean and appear to be tens of thousands of years old. As such DBC is regarded as highly refractory. In the current study, the photo-lability of DBC, DOC and coloured dissolved organic matter (CDOM; ultraviolet-visible absorbance were determined over the course of a 28 day irradiation of North Atlantic Deep Water under a solar simulator. During the irradiation DBC fell from 1044 ± 164 nM-C to 55 ± 15 nM-C, a 20-fold decrease in concentration. Dissolved black carbon photo-degradation was more rapid and more extensive than for bulk CDOM and DOC. The concentration of DBC correlated with CDOM absorbance and the quality of DBC indicated by the ratios of different BPCAs correlated with CDOM absorbance spectral slope, suggesting the optical properties of CDOM may provide a proxy for both DBC concentrations and quality in natural waters. Further, the photo-lability of components of the DBC pool increased with their degree of aromatic condensation. These trends indicate that a continuum of compounds of varying photo-lability exists within the marine DOC pool. In this continuum, photo-lability scales with aromatic character, specifically the degree of condensation. Scaling the rapid photo-degradation of DBC to rates of DOC photo-mineralisation for the global ocean leads to an estimated photo-chemical half-life for oceanic DBC of less than 800 years. This is more than an order of magnitude shorter than the apparent age of DBC in the ocean. Consequently, photo-degradation is posited as the primary sink for oceanic DBC and the apparent survival of DBC molecules in the oceans for millennia appears to be facilitated not by their

  5. Photo-lability of deep ocean dissolved black carbon

    Science.gov (United States)

    Stubbins, A.; Niggemann, J.; Dittmar, T.

    2012-05-01

    Dissolved black carbon (DBC), defined here as condensed aromatics isolated from seawater via PPL solid phase extraction and quantified as benzenepolycarboxylic acid (BPCA) oxidation products, is a significant component of the oceanic dissolved organic carbon (DOC) pool. These condensed aromatics are widely distributed in the open ocean and appear to be tens of thousands of years old. As such DBC is regarded as highly refractory. In the current study, the photo-lability of DBC, DOC and coloured dissolved organic matter (CDOM; ultraviolet-visible absorbance) were determined over the course of a 28 day irradiation of North Atlantic Deep Water under a solar simulator. During the irradiation DBC fell from 1044 ± 164 nM-C to 55 ± 15 nM-C, a 20-fold decrease in concentration. Dissolved black carbon photo-degradation was more rapid and more extensive than for bulk CDOM and DOC. The concentration of DBC correlated with CDOM absorbance and the quality of DBC indicated by the ratios of different BPCAs correlated with CDOM absorbance spectral slope, suggesting the optical properties of CDOM may provide a proxy for both DBC concentrations and quality in natural waters. Further, the photo-lability of components of the DBC pool increased with their degree of aromatic condensation. These trends indicate that a continuum of compounds of varying photo-lability exists within the marine DOC pool. In this continuum, photo-lability scales with aromatic character, specifically the degree of condensation. Scaling the rapid photo-degradation of DBC to rates of DOC photo-mineralisation for the global ocean leads to an estimated photo-chemical half-life for oceanic DBC of less than 800 years. This is more than an order of magnitude shorter than the apparent age of DBC in the ocean. Consequently, photo-degradation is posited as the primary sink for oceanic DBC and the apparent survival of DBC molecules in the oceans for millennia appears to be facilitated not by their inherent inertness but

  6. Toxicity assessment of carbon black waste: A by-product from oil refineries.

    Science.gov (United States)

    Zhen, Xu; Ng, Wei Cheng; Fendy; Tong, Yen Wah; Dai, Yanjun; Neoh, Koon Gee; Wang, Chi-Hwa

    2017-01-05

    In Singapore, approximately 30t/day of carbon-based solid waste are produced from petrochemical processes. This carbon black waste has been shown to possess physical properties that are characteristic of a good adsorbent such as high external surface area. Therefore, there is a growing interest to reutilize and process this carbon black waste into secondary materials such as adsorbents. However, the carbon black waste obtained from petrochemical industries may contain heavy metals that are hazardous to human health and the environment, hence restricting its full potential for re-utilization. Therefore, it is important to examine the possible toxicity effects and toxicity mechanism of carbon black waste on human health. In this study, inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis showed that the heavy metals, vanadium (V), molybdenum (Mo) and nickel (Ni), were present in the carbon black waste in high concentrations. Three human cell lines (HepG2 cells, MRC-5 cells and MDA-MB-231 cells) were used to investigate the toxicity of carbon black waste extract in a variety of in vitro assays. Results from MTS assays indicated that carbon black waste extract decreased the viability of all three cell lines in a dose and time-dependent manner. Observations from confocal microscopy further confirmed this phenomenon. Flow cytometry assay also showed that carbon black waste extract induced apoptosis of human cell lines, and the level of apoptosis increased with increasing waste concentration. Results from reactive oxygen species (ROS) assay indicated that carbon black waste extract induced oxidative stress by increasing intracellular ROS generation in these three human cell lines. Moreover, induction of oxidative damage in these cells was also observed through the alteration of glutathione (GSH) and superoxide dismutase (SOD) activities. Last but not least, by treating the cells with V-spiked solution of concentration equivalent to that found in the

  7. Black Carbon at the Mt. Bachelor Observatory Field Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Jaffe, Dan A. [Univ. of Washington, Bothell, WA (United States); Sedlacek, Arthur [Brookhaven National Lab. (BNL), Upton, NY (United States); Laing, James R. [Univ. of Washington, Bothell, WA (United States)

    2017-03-01

    This campaign was initiated to measure refractory black carbon (rBC, as defined in Schwarz et al. (2010)) at the Mt. Bachelor Observatory (MBO) using the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility single-particle soot photometer (SP2; unit 54). MBO is a high-elevation site located on the summit of Mt. Bachelor in central Oregon, USA (43.979°N, 121.687°W, 2,763 meters ASL). This site is operated by Professor Dan Jaffe’s group at the University of Washington Bothell and has been used continuously as an atmospheric observatory for the past 12 years (Jaffe et al., 2005; Gratz et al., 2014). The location of MBO allows frequent sampling of the free troposphere along with a wide array of plumes from regional and distant sources. MBO is currently supported with funding from the National Science Foundation (NSF) to the Principal Investigator (PI; D. Jaffe) via the project “Influence of Free Tropospheric Ozone and PM on Surface Air Quality in the Western U.S.” (#1447832) covering the period 03/15/2015 to 02/28/2018. The SP2 instrument from Droplet Measurement Technologies provides particle-resolved measurements of rBC mass loading, size and mass distributions, and mixing state. The SP2 was installed at MBO on 6/27/2016 and ran through 9/23/2016. Additional measurements at MBO during this campaign included carbon monoxide (CO), fine particulate matter (PM1), aerosol light scattering coefficients (σscat) at three wavelengths using a TSI nephelometer, aerosol absorption coefficients (σabs) with the Brechtel tricolor absorption photometer (TAP), aerosol number size distributions with a scanning mobility particle sizer spectrometer (SMPS), and black carbon (eBC) with an aethalometer. BC data from this campaign have been submitted to the ARM Data Archive. Black carbon (BC) is the predominant light-absorbing aerosol constituent in the atmosphere, and is estimated to exert a positive radiative forcing second only to CO

  8. Black carbon or brown carbon? The nature of light-absorbing carbonaceous aerosols

    Directory of Open Access Journals (Sweden)

    M. O. Andreae

    2006-01-01

    Full Text Available Although the definition and measurement techniques for atmospheric 'black carbon' ('BC' or 'elemental carbon'' ('EC' have long been subjects of scientific controversy, the recent discovery of light-absorbing carbon that is not black ('brown carbon, Cbrown' makes it imperative to reassess and redefine the components that make up light-absorbing carbonaceous matter (LAC in the atmosphere. Evidence for the atmospheric presence of Cbrown comes from (1 spectral aerosol light absorption measurements near specific combustion sources, (2 observations of spectral properties of water extracts of continental aerosol, (3 laboratory studies indicating the formation of light-absorbing organic matter in the atmosphere, and (4 indirectly from the chemical analogy of aerosol species to colored natural humic substances. We show that brown carbon may severely bias measurements of 'BC' and 'EC' over vast parts of the troposphere, especially those strongly polluted by biomass burning, where the mass concentration of Cbrown is high relative to that of soot carbon. Chemical measurements to determine 'EC' are biased by the refractory nature of Cbrown as well as by complex matrix interferences. Optical measurements of 'BC' suffer from a number of problems: (1 many of the presently used instruments introduce a substantial bias into the determination of aerosol light absorption, (2 there is no unique conversion factor between light absorption and 'EC' or 'BC' concentration in ambient aerosols, and (3 the difference in spectral properties between the different types of LAC, as well as the chemical complexity of Cbrown, lead to several conceptual as well as practical complications. We also suggest that due to the sharply increasing absorption of Cbrown towards the UV, single-wavelength light absorption measurements may not be adequate for the assessment of absorption of solar radiation in the troposphere. We discuss the possible consequences of these effects for our

  9. Organic carbon isotopes of the Sinian and Early Cambrian black shales on Yangtze Platform, China

    Institute of Scientific and Technical Information of China (English)

    李任伟; 卢家烂; 张淑坤; 雷加锦

    1999-01-01

    Organic matter of the Sinian and early Cambrian black shales on the Yangtze Platform belongs to the light carbon group of isotopes with the δ13C values from - 27 % to -35 % , which are lower than those of the contemporaneously deposited carbonates and phosphorites. A carbon isotope-stratified paleooceanographic model caused by upwelling is proposed, which can be used not only to interpret the characteristics of organic carbon isotopic compositions of the black shales, but also to interpret the paleogeographic difference in the organic carbon isotope compositions of various types of sedimentary rocks.

  10. Influence of sample composition on aerosol organic and black carbon determinations

    Energy Technology Data Exchange (ETDEWEB)

    Novakov, T.; Corrigan, C.E.

    1995-07-01

    In this paper we present results on characterization of filter-collected redwood (Sequoia sempevirens)-needle and eucalyptus smoke particles by thermal, optical, and solvent extraction methods. Our results demonstrate that organic and black carbon concentrations determined by thermal and optical methods are not only method dependent, but also critically influenced by the overall chemical composition of the samples. These conclusions are supported by the following: (1) the organic fraction of biomass smoke particles analyzed includes a component, ranging in concentration from about 6-20% of total carbon or from 16-30% of organic carbon, that is relatively non-volatile and has a combustion temperature close to that of black carbon; (2) presence of K or Na in biomass smoke samples lowers the combustion temperatures of this organic component and of black carbon, making their combustion properties indistinguishable; (3) about 20% of total organic material is nonvolatile when heated to 550{degrees}C in an inert atmosphere. Consequently, thermal methods that rely on a specific temperature to separate organic from black carbon may either underestimate or overestimate the black and organic carbon concentrations, depending on the amounts of Na and K and on the composition and concentration of organic material present in a sample. These analytical uncertainties and, under some conditions, absorption by organic material may contribute to the variability of empirically derived proportionality between light transmission through filter deposits and black carbon concentrations.

  11. An approach to a black carbon emission inventory for Mexico by two methods.

    Science.gov (United States)

    Cruz-Núñez, Xochitl

    2014-05-01

    A black carbon (BC) emission inventory for Mexico is presented. Estimate was performed by using two approaches, based on fuel consumption and emission factors in a top-down scheme, and the second from PM25 emission data and its correlation with black carbon by source category, assuming that black carbon=elemental carbon. Results show that black carbon emissions are in interval 53-473Gg using the fuel consumption approach and between 62 and 89 using the sector method. Black carbon key sources come from biomass burning in the rural sector, with 47 percent share to the National total. Mobile sources emissions account to 16% to the total. An opportunity to reduce, in the short-term, carbon dioxide equivalent (CO2-eq) emissions by reducing black carbon emissions would be obtained in reducing emissions mainly from biomass burning in rural housing sector and diesel emissions in the transport sector with important co-benefits in direct radiative forcing, public health and air quality.

  12. Constraints on rainbow gravity functions from black hole thermodynamics

    CERN Document Server

    Gangopadhyay, Sunandan

    2016-01-01

    In this paper, we investigate the thermodynamic properties of black holes in the framework of rainbow gravity. By considering rainbow functions in the metric of Schwarzschild and Reissner-Nordstr\\"{o}m black holes, remnant and critical masses are found to exist. Demanding the universality of logarithmic corrections to the semi-classical area law for the entropy leads to constraining the form of the rainbow functions. The mass output and the radiation rate for these constrained form of rainbow functions have been computed for different values of the rainbow parameter $\\eta$ and have striking similarity to those derived from the generalized uncertainty principle.

  13. The impact of black wattle encroachment of indigenous grasslands on soil carbon, Eastern Cape, South Africa

    DEFF Research Database (Denmark)

    Oelofse, Myles; Birch-Thomsen, Torben; Magid, Jakob;

    2016-01-01

    adverse environmental impacts in South Africa. Little is known about the effects of black wattle encroachment on soil carbon, therefore the aim of this study was to investigate the impact of black wattle encroachment of natural grassland on soil carbon stocks and dynamics. Focussing on two sites...... in the Eastern Cape, South Africa, the study analysed carbon stocks in soil and litter on a chronosequence of black wattle stands of varying ages (up to >50 years) and compared these with adjacent native grassland. The study found that woody encroachment of grassland at one site had an insignificant effect...

  14. Variable effects of labile carbon on the carbon use of different microbial groups in black slate degradation

    Science.gov (United States)

    Seifert, Anne-Gret; Trumbore, Susan; Xu, Xiaomei; Zhang, Dachung; Kothe, Erika; Gleixner, Gerd

    2011-05-01

    Weathering of ancient organic matter contributes significantly to biogeochemical carbon cycles over geological times. The principle role of microorganisms in this process is well recognized. However, information is lacking on the contribution of individual groups of microorganisms and on the effect of labile carbon sources to the degradation process. Therefore, we investigated the contribution of fungi, Gram-positive and Gram-negative bacteria in the degradation process using a column experiment. Investigations were performed on low metamorphic black slates. All columns contained freshly crushed, sieved (0.63-2 mm), not autoclaved black slates. Two columns were inoculated with the lignite-degrading fungus Schizophyllum commune and received a culture medium containing 13C labeled glucose, two columns received only this culture medium and two control columns received only water. The total mass balance was calculated from all carbon added to the slate and the CO 2 and DOC losses. Phospholipid fatty acids (PLFA) were extracted to investigate microbial communities. We used both the compound specific 14C and 13C signal of the PLFA to quantify carbon uptake from black slates and the glucose of the culture medium, respectively. The total carbon loss in these columns exceeded the amount of added carbon by approximately 60%, indicating that black slate carbon has been used. PLFA associated with Gram-positive bacteria dominated the indigenous community and took up 22% of carbon from black slate carbon, whereas PLFA of Gram-negative bacteria used only 8% of carbon from the slates. PLFA of Gram-negative bacteria and fungi were both mostly activated by the glucose addition. The added Schizophyllum did not establish well in the columns and was overgrown by the indigenous microbial community. Our results suggest that especially Gram-positive bacteria are able to live on and degrade black slate material. They also benefit from easy degradable carbon from the nutrient broth. In

  15. Heterogeneous atoms in laser-induced synthesis of carbon black

    Science.gov (United States)

    Popovici, E.; Gavrila Florescu, L.; Soare, I.; Scarisoreanu, M.; Sandu, I.; Prodan, G.; Fleaca, C. T.; Morjan, I.; Voicu, I.

    2009-03-01

    Based on a high temperature hydrocarbon/heterogeneous atoms system of well-established composition, the formation of carbon nanostructures by laser-induced pyrolysis is related to the presence of heteroatoms in the reactants. In this paper, the goal is to underline the influence of some heteroatoms on the morphology and functionalizing nanostructured carbon materials by changing both gas composition and experimental parameters, with the focus to drive these materials into a regime where they can naturally interface with the surrounding matter. To investigate, in the versatile laser pyrolysis method, how to in situ modulate - through the presence of heterogeneous atoms - the characteristics of carbon nanopowders claimed by specific application is a challenge. Some preliminary results confirm experimentally their particular behavior during interaction with polymer matrices of some nanocomposites.

  16. Retrieval of Black Carbon Absorption from Proposed Satellite Measurements Over the Ocean Glint

    Science.gov (United States)

    Kaufman, Y. J.; Matins, J. V.; Remer, L. A.; Schoeberl, M. R.; Yamasoe, M. A.; Lau, William K. M. (Technical Monitor)

    2001-01-01

    Haze and air pollution includes many chemicals that together form small particles suspended in the air called aerosols. One of the main ingredients found to affect climate and human health is Black Carbon. Black particles emitted from engines that do not burn the fuel completely, e.g. old trucks. Black carbon absorption of sunlight emerges as one of the key components of man-made forcing of climate. However, global characterization of black carbon emissions, distribution and pathways in which it can affect the amount of solar radiation absorbed by the atmosphere is very uncertain. A new method is proposed to measure sunlight absorption by fine aerosol particles containing black carbon over the ocean glint from a satellite mission designed for this purpose. The satellite will scan the same spot over the ocean in the glint plane and a plane 40 degrees off-glint a minute apart, collecting measurements of the reflected light across the solar spectrum. First the dark ocean off the glint is used to derive aerosol properties. Then the black carbon absorption is derived prop the attenuation of the bright glint by the aerosol layer. Such measurements if realized in a proposed future mission - COBRA are expected to produce global monthly climatology of black carbon absorption with high accuracy (110 to 15%) that can show their effect on climate.

  17. Black carbon, a 'hidden' player in the global C cycle

    Science.gov (United States)

    Santín, C.; Doerr, S. H.

    2012-04-01

    During the 2011 alone more than 600 scientific papers about black carbon (BC) were published, half of them dealing with soils (ISI Web of Knowledge, accessed 15/01/2012). If the search is extended to the other terms by which BC is commonly named (i.e. biochar, charcoal, pyrogenic C or soot), the number of 2011 publications increases to >2400, 20% of them also related to soils. These figures confirm BC as a well-known feature in the scientific literature and, thus, in our research community. In fact, there is a wide variety of research topics where BC is currently studied: from its potential as long-term C reservoir in soils (man-made biochar), to its effects on the Earth's radiation balance (soot-BC), including its value as indicator in paleoenvironmental studies (charcoal) or, even surprisingly, its use in suicide attempts. BC is thus relevant to many aspects of our environment, making it a very far-reaching, but also very complex topic. When focusing 'only' on the role of BC in the global C cycle, numerous questions arise. For example: (i) how much BC is produced by different sources (i.e. vegetation fires, fossil fuel and biofuel combustion); (ii) what are the main BC forms and their respective proportions generated (i.e. proportion of atmospheric BC [BC-soot] and the solid residues [char-BC]); (iii) where does this BC go (i.e. main mobilization pathways and sinks); (iv) how long does BC stay in the different systems (i.e. residence times in soils, sediments, water and atmosphere); (v) which are the BC stocks and its main transformations within and between the different systems (i.e. BC preservation, alteration and mineralization); (vi) what is the interaction of BC with other elements and how does this influence BC half-life (i.e. physical protection, interaction with pollutants, priming effects in other organic materials)? These questions, and some suggestions about how to tackle these, will be discussed in this contribution. It will focus in particular on the

  18. Atmospheric deposition of organic and black carbon to the global oceans

    Science.gov (United States)

    Jurado, Elena; Dachs, Jordi; Duarte, Carlos M.; Simó, Rafel

    Atmospheric deposition of total organic carbon (OC) and black carbon (BC) is lacking or not fully accounted in most current models of the global carbon cycling, specially those fluxes related to gas phase OC. Here, we develop and apply a methodology to estimate wet and dry deposition of total OC to the oceans, based on monthly satellite measurements of aerosol size distributions, wind speed, etc., and estimates of deposition for aerosols and organic compounds. The parameterization of dry deposition velocities account for the dependence of turbulent transport with aerosol diameter, wind speed and the formation of marine aerosol, etc. Gravitational settling is estimated as a function of wet particle diameter, thus including hygroscopic growth due to ambient humidity. Global dry deposition of aerosol OC is estimated to be 11 Tg C y -1 and wet deposition of particle and gaseous OC are estimated as 47 and 187 Tg C y -1, respectively. Due to their pulsing variability, wet deposition fluxes can be important locally and as a temporal source of OC to surface waters. Dry and wet deposition of black carbon to the global ocean are estimated to be 2 and 10 Tg C yr -1, respectively, with higher fluxes in the northern hemisphere and for inter-tropical regions. Finally, considerations on the potential magnitude of the hitherto neglected gross air-sea diffusive exchange fluxes of OC are discussed. Even though the magnitude and direction of these cannot be constrained here, evidence of its important role is given. This study, thus, shows that there is an important spatial and temporal variability in atmosphere-ocean exchanges of OC and BC at different scales, and calls for the need for further research on the important role that these exchanges play in the global carbon cycle.

  19. Global anthropogenic emissions of particulate matter including black carbon

    Directory of Open Access Journals (Sweden)

    Z. Klimont

    2017-07-01

    Full Text Available This paper presents a comprehensive assessment of historical (1990–2010 global anthropogenic particulate matter (PM emissions including the consistent and harmonized calculation of mass-based size distribution (PM1, PM2. 5, PM10, as well as primary carbonaceous aerosols including black carbon (BC and organic carbon (OC. The estimates were developed with the integrated assessment model GAINS, where source- and region-specific technology characteristics are explicitly included. This assessment includes a number of previously unaccounted or often misallocated emission sources, i.e. kerosene lamps, gas flaring, diesel generators, refuse burning; some of them were reported in the past for selected regions or in the context of a particular pollutant or sector but not included as part of a total estimate. Spatially, emissions were calculated for 172 source regions (as well as international shipping, presented for 25 global regions, and allocated to 0.5°  ×  0.5° longitude–latitude grids. No independent estimates of emissions from forest fires and savannah burning are provided and neither windblown dust nor unpaved roads emissions are included. We estimate that global emissions of PM have not changed significantly between 1990 and 2010, showing a strong decoupling from the global increase in energy consumption and, consequently, CO2 emissions, but there are significantly different regional trends, with a particularly strong increase in East Asia and Africa and a strong decline in Europe, North America, and the Pacific region. This in turn resulted in important changes in the spatial pattern of PM burden, e.g. European, North American, and Pacific contributions to global emissions dropped from nearly 30 % in 1990 to well below 15 % in 2010, while Asia's contribution grew from just over 50 % to nearly two-thirds of the global total in 2010. For all PM species considered, Asian sources represented over 60 % of the global

  20. Global anthropogenic emissions of particulate matter including black carbon

    Science.gov (United States)

    Klimont, Zbigniew; Kupiainen, Kaarle; Heyes, Chris; Purohit, Pallav; Cofala, Janusz; Rafaj, Peter; Borken-Kleefeld, Jens; Schöpp, Wolfgang

    2017-07-01

    This paper presents a comprehensive assessment of historical (1990-2010) global anthropogenic particulate matter (PM) emissions including the consistent and harmonized calculation of mass-based size distribution (PM1, PM2. 5, PM10), as well as primary carbonaceous aerosols including black carbon (BC) and organic carbon (OC). The estimates were developed with the integrated assessment model GAINS, where source- and region-specific technology characteristics are explicitly included. This assessment includes a number of previously unaccounted or often misallocated emission sources, i.e. kerosene lamps, gas flaring, diesel generators, refuse burning; some of them were reported in the past for selected regions or in the context of a particular pollutant or sector but not included as part of a total estimate. Spatially, emissions were calculated for 172 source regions (as well as international shipping), presented for 25 global regions, and allocated to 0.5° × 0.5° longitude-latitude grids. No independent estimates of emissions from forest fires and savannah burning are provided and neither windblown dust nor unpaved roads emissions are included. We estimate that global emissions of PM have not changed significantly between 1990 and 2010, showing a strong decoupling from the global increase in energy consumption and, consequently, CO2 emissions, but there are significantly different regional trends, with a particularly strong increase in East Asia and Africa and a strong decline in Europe, North America, and the Pacific region. This in turn resulted in important changes in the spatial pattern of PM burden, e.g. European, North American, and Pacific contributions to global emissions dropped from nearly 30 % in 1990 to well below 15 % in 2010, while Asia's contribution grew from just over 50 % to nearly two-thirds of the global total in 2010. For all PM species considered, Asian sources represented over 60 % of the global anthropogenic total, and residential combustion

  1. Russia's black carbon emissions: focus on diesel sources

    Science.gov (United States)

    Kholod, Nazar; Evans, Meredydd; Kuklinski, Teresa

    2016-09-01

    Black carbon (BC) is a significant climate forcer with a particularly pronounced forcing effect in polar regions such as the Russian Arctic. Diesel combustion is a major global source of BC emissions, accounting for 25-30 % of all BC emissions. While the demand for diesel is growing in Russia, the country's diesel emissions are poorly understood. This paper presents a detailed inventory of Russian BC emissions from diesel sources. Drawing on a complete Russian vehicle registry with detailed information about vehicle types and emission standards, this paper analyzes BC emissions from diesel on-road vehicles. We use the COPERT emission model (COmputer Programme to calculate Emissions from Road Transport) with Russia-specific emission factors for all types of on-road vehicles. On-road diesel vehicles emitted 21 Gg of BC in 2014: heavy-duty trucks account for 60 % of the on-road BC emissions, while cars represent only 5 % (light commercial vehicles and buses account for the remainder). Using Russian activity data and fuel-based emission factors, the paper also presents BC emissions from diesel locomotives and ships, off-road engines in industry, construction and agriculture, and generators. The study also factors in the role of superemitters in BC emissions from diesel on-road vehicles and off-road sources. The total emissions from diesel sources in Russia are estimated to be 49 Gg of BC and 17 Gg of organic carbon (OC) in 2014. Off-road diesel sources emitted 58 % of all diesel BC in Russia.

  2. Black carbon reduction will weaken the aerosol net cooling effect

    Directory of Open Access Journals (Sweden)

    Z. L. Wang

    2014-12-01

    Full Text Available Black carbon (BC, a distinct type of carbonaceous material formed from the incomplete combustion of fossil and biomass based fuels under certain conditions, can interact with solar radiation and clouds through its strong light-absorption ability, thereby warming the Earth's climate system. Some studies have even suggested that global warming could be slowed down in a short term by eliminating BC emission due to its short lifetime. In this study, we estimate the influence of removing some sources of BC and other co-emitted species on the aerosol radiative effect by using an aerosol-climate coupled model BCC_AGCM2.0.1_CUACE/Aero, in combination with the aerosol emissions from the Representative Concentration Pathways (RCPs scenarios. We find that the global annual mean aerosol net cooling effect at the top of the atmosphere (TOA will be enhanced by 0.12 W m−2 compared with present-day conditions if the BC emission is reduced exclusively to the level projected for 2100 based on the RCP2.6 scenario. This will be beneficial for the mitigation of global warming. However, the global annual mean aerosol net cooling effect at the TOA will be weakened by 1.7–2.0 W m−2 relative to present-day conditions if emissions of BC and co-emitted sulfur dioxide and organic carbon are simultaneously reduced as the most close conditions to the actual situation to the level projected for 2100 in different ways based on the RCP2.6, RCP4.5, and RCP8.5 scenarios. Because there are no effective ways to remove the BC exclusively without influencing the other co-emitted components, our results therefore indicate that a reduction in BC emission can lead to an unexpected warming on the Earth's climate system in the future.

  3. Atmospheric black carbon and sulfate concentrations in Northeast Greenland

    Directory of Open Access Journals (Sweden)

    A. Massling

    2015-04-01

    Full Text Available Measurements of Black Carbon (BC in aerosols at the high Arctic field site Villum Research Station (VRS at Station Nord in North Greenland showed a seasonal variation in BC concentrations with a maximum in winter and spring at ground level. The data was obtained using a Multi Angle Absorption Photometer (MAAP. A similar seasonal pattern was found for sulfate concentrations with a maximum level during winter and spring analyzed by ion chromatography. A correlation between BC and sulfate concentrations was observed over the years 2011 to 2013. This finding gives the hint that most likely transport of primary emitted BC particles to the Arctic was accompanied by aging of the aerosols through condensational processes. This process may have led to the formation of secondary inorganic matter and further transport of BC particles as cloud processing and further washout of particles is less likely based on the typically observed transport patterns of air masses arriving at VRS. Additionally, concentrations of EC (elemental carbon based on a thermo-optical method were determined and compared to BC measurements. Model estimates of the climate forcing due to BC in the Arctic are based on contributions of long-range transported BC during spring and summer. The measured concentrations were here compared with model results obtained by the Danish Hemispheric Model, DEHM. Good agreement between measured and modeled concentrations of both BC and sulfate was observed. The dominant source is found to be combustion of fossil fuel with biomass burning as a minor though significant source. During winter and spring the Arctic atmosphere is known to be impacted by long-range transport of BC and associated with the Arctic haze phenomenon.

  4. The scavenging processes controlling the seasonal cycle in Arctic sulphate and black carbon aerosol

    National Research Council Canada - National Science Library

    Browse, J; Carslaw, K. S; Arnold, S. R; Pringle, K; Boucher, O

    2012-01-01

    .... Here, we use a global aerosol microphysics model (GLOMAP) and surface-level aerosol observations to understand how wet scavenging processes control the seasonal variation in Arctic black carbon (BC...

  5. Micromorphological evidence of black carbon in colluvial soils from NW Spain

    NARCIS (Netherlands)

    Kaal, J.; van Mourik, J.M.

    2008-01-01

    Biomass burning produces a residue called black carbon (BC). Black C is generally considered to be highly resistant against biodegradation and has a potential role in the global C cycle, but is difficult to identify and quantify when subjected to prolonged degradation in terrestrial sediments. The c

  6. Characterization of Black and Brown Carbon Concentrations and Sources during winter in Beijing

    Science.gov (United States)

    Yan, Caiqing; Liu, Yue; Hansen, Anthony D. A.; Močnik, Griša; Zheng, Mei

    2017-04-01

    Carbonaceous aerosols, including black carbon (BC) and organic carbon (OC), play important roles in air quality, human health, and climate change. A better understanding of sources of light-absorbing carbonaceous aerosol (including black carbon and brown carbon) is particular critical for formulating emission-based control strategies and reducing uncertainties in current aerosol radiative forcing estimates. Beijing, the capital of China, has experienced serious air pollution problems and high concentrations of carbonaceous aerosols in recent years, especially during heating seasons. During November and December of 2016, several severe haze episodes occurred in Beijing, with hourly average PM2.5 mass concentration up to 400 μg/m3. In this study, concentration levels and sources of black carbon and brown carbon were investigated based on 7-wavelength Aethalometer (AE-33) with combination of other PM2.5 chemical composition information. Contributions of traffic and non-traffic emissions (e.g., coal combustion, biomass burning) were apportioned, and brown carbon was separated from black carbon. Our preliminary results showed that (1) Concentrations of BC were around 5.3±4.2 μg/m3 during the study period, with distinct diurnal variations during haze and non-haze days. (2) Traffic emissions contributed to about 37±17% of total BC, and exhibited higher contributions during non-haze days compared to haze days. (3) Coal combustion was a major source of black carbon and brown carbon in Beijing, which was more significant compared to biomass burning. Sources and the relative contributions to black carbon and brown carbon during haze and non-haze days will be further discussed.

  7. Improved piezoelectricity of PVDF-HFP/carbon black composite films

    Science.gov (United States)

    Wu, Liangke; Yuan, Weifeng; Hu, Ning; Wang, Zhongchang; Chen, Chunlin; Qiu, Jianhui; Ying, Ji; Li, Yuan

    2014-04-01

    We report a substantial improvement of piezoelectricity for poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) copolymer films by introducing carbon black (CB) into the PVDF-HFP to form PVDF-HFP/CB composite films. The optimized output voltage of the composite film at an optimal CB content of 0.5 wt% is found to be 204% of the pristine PVDF-HFP film. Its harvested electrical power density is 464% and 561% of the pristine PVDF-HFP film by using ac and dc circuits, respectively. Through Fourier transform infrared spectroscopy analysis, differential scanning calorimetry analysis, and polarized optical microscopy observations, we clarify the enhancement mechanism of piezoelectricity for the PVDF-HFP/CB composite films. We find that the added CB acts as nucleating agent during the initial formation of crystals, but imposes an insignificant effect on the α-β phase transformation during stretching. We also demonstrate that the addition of optimal CB reduces crystal size yet increases the number of crystals in the composite films. This is beneficial for the formation of elongated, oriented and fibrillar crystalline morphology during stretching and consequently results in a highly efficient poling process. The addition of overdosed CB leads to the formation of undersized crystals, lowered crystallinity, and hence reduced piezoelectric performance of the PVDF-HFP/CB composite films.

  8. Siberian Arctic black carbon sources constrained by model and observation

    Science.gov (United States)

    Winiger, Patrik; Andersson, August; Eckhardt, Sabine; Stohl, Andreas; Semiletov, Igor P.; Dudarev, Oleg V.; Charkin, Alexander; Shakhova, Natalia; Klimont, Zbigniew; Heyes, Chris; Gustafsson, Örjan

    2017-02-01

    Black carbon (BC) in haze and deposited on snow and ice can have strong effects on the radiative balance of the Arctic. There is a geographic bias in Arctic BC studies toward the Atlantic sector, with lack of observational constraints for the extensive Russian Siberian Arctic, spanning nearly half of the circum-Arctic. Here, 2 y of observations at Tiksi (East Siberian Arctic) establish a strong seasonality in both BC concentrations (8 ngṡm-3 to 302 ngṡm-3) and dual-isotope-constrained sources (19 to 73% contribution from biomass burning). Comparisons between observations and a dispersion model, coupled to an anthropogenic emissions inventory and a fire emissions inventory, give mixed results. In the European Arctic, this model has proven to simulate BC concentrations and source contributions well. However, the model is less successful in reproducing BC concentrations and sources for the Russian Arctic. Using a Bayesian approach, we show that, in contrast to earlier studies, contributions from gas flaring (6%), power plants (9%), and open fires (12%) are relatively small, with the major sources instead being domestic (35%) and transport (38%). The observation-based evaluation of reported emissions identifies errors in spatial allocation of BC sources in the inventory and highlights the importance of improving emission distribution and source attribution, to develop reliable mitigation strategies for efficient reduction of BC impact on the Russian Arctic, one of the fastest-warming regions on Earth.

  9. Field Measurements of Black Carbon Yields from Gas Flaring.

    Science.gov (United States)

    Conrad, Bradley M; Johnson, Matthew R

    2017-02-07

    Black carbon (BC) emissions from gas flaring in the oil and gas industry are postulated to have critical impacts on climate and public health, but actual emission rates remain poorly characterized. This paper presents in situ field measurements of BC emission rates and flare gas volume-specific BC yields for a diverse range of flares. Measurements were performed during a series of field campaigns in Mexico and Ecuador using the sky-LOSA optical measurement technique, in concert with comprehensive Monte Carlo-based uncertainty analyses. Parallel on-site measurements of flare gas flow rate and composition were successfully performed at a subset of locations enabling direct measurements of fuel-specific BC yields from flares under field conditions. Quantified BC emission rates from individual flares spanned more than 4 orders of magnitude (up to 53.7 g/s). In addition, emissions during one notable ∼24-h flaring event (during which the plume transmissivity dropped to zero) would have been even larger than this maximum rate, which was measured as this event was ending. This highlights the likely importance of superemitters to global emission inventories. Flare gas volume-specific BC yields were shown to be strongly correlated with flare gas heating value. A newly derived correlation fitting current field data and previous lab data suggests that, in the context of recent studies investigating transport of flare-generated BC in the Arctic and globally, impacts of flaring in the energy industry may in fact be underestimated.

  10. Black carbon aerosols and the third polar ice cap

    Directory of Open Access Journals (Sweden)

    S. Menon

    2009-12-01

    Full Text Available Recent thinning of glaciers over the Himalayas (sometimes referred to as the third polar region have raised concern on future water supplies since these glaciers supply water to large river systems that support millions of people inhabiting the surrounding areas. Black carbon (BC aerosols, released from incomplete combustion, have been increasingly implicated as causing large changes in the hydrology and radiative forcing over Asia and its deposition on snow is thought to increase snow melt. In India BC from biofuel combustion is highly prevalent and compared to other regions, BC aerosol amounts are high. Here, we quantify the impact of BC aerosols on snow cover and precipitation from 1990 to 2010 over the Indian subcontinental region using two different BC emission inventories. New estimates indicate that Indian BC from coal and biofuel are large and transport is expected to expand rapidly in coming years. We show that over the Himalayas, from 1990 to 2000, simulated snow/ice cover decreases by ~0.9% due to aerosols. The contribution of the enhanced Indian BC to this decline is ~30%, similar to that simulated for 2000 to 2010. Spatial patterns of modeled changes in snow cover and precipitation are similar to observations (from 1990 to 2000, and are mainly obtained with the newer BC estimates.

  11. Black carbon aerosols and the third polar ice cap

    Directory of Open Access Journals (Sweden)

    S. Menon

    2010-05-01

    Full Text Available Recent thinning of glaciers over the Himalayas (sometimes referred to as the third polar region have raised concern on future water supplies since these glaciers supply water to large river systems that support millions of people inhabiting the surrounding areas. Black carbon (BC aerosols, released from incomplete combustion, have been increasingly implicated as causing large changes in the hydrology and radiative forcing over Asia and its deposition on snow is thought to increase snow melt. In India BC emissions from biofuel combustion is highly prevalent and compared to other regions, BC aerosol amounts are high. Here, we quantify the impact of BC aerosols on snow cover and precipitation from 1990 to 2010 over the Indian subcontinental region using two different BC emission inventories. New estimates indicate that Indian BC emissions from coal and biofuel are large and transport is expected to expand rapidly in coming years. We show that over the Himalayas, from 1990 to 2000, simulated snow/ice cover decreases by ~0.9% due to aerosols. The contribution of the enhanced Indian BC to this decline is ~36%, similar to that simulated for 2000 to 2010. Spatial patterns of modeled changes in snow cover and precipitation are similar to observations (from 1990 to 2000, and are mainly obtained with the newer BC estimates.

  12. Black Carbon Trends over Several Decades at Multiple Locations

    Science.gov (United States)

    Preble, C. V.; Hadley, O. L.; Bond, T. C.; Kirchstetter, T.

    2012-12-01

    Archived air quality data in the U.S. and Europe can be used to reconstruct past trends in black carbon (BC), an indicator of fossil fuel combustion and biomass burning. Here, we consider coefficient of haze (COH) data that was extensively measured in California, New Jersey, and other North American locations from the mid-1960s to the turn of the century. We reinstated COH monitors alongside aethalometers in Vallejo and San Jose, California, and after two years of air monitoring determined that COH is proportional to and, thus, can be used to infer past concentrations of BC. Analyzing COH data sets, we found that BC concentrations markedly decreased from 1965 to 2000 in both California and New Jersey. The opposing trend of increasing energy consumption over the same period indicates successful regulatory control of sources and a shift from dirtier to cleaner fuels. As air quality improved over four decades, a seasonal trend of maximum BC concentrations in winter persisted in California but, somewhat surprisingly, disappeared in New Jersey. A strong weekly cycle of lowest BC concentrations on weekends was evident in California and New Jersey, suggesting that diesel traffic, which exhibits a similar weekly cycle, has been a major source of BC in both states. Our extended analysis will include BC trends in other regions of North America and Europe and will be applied to understand BC radiative forcing in California and deposition of pollutants in the Arctic.

  13. Characteristics and source of black carbon aerosol over Taklimakan Desert

    Institute of Scientific and Technical Information of China (English)

    FU; S.Joshua

    2010-01-01

    Black carbon(BC) and PM10 in the center of the Taklimakan Desert were online monitored in the whole year of 2007.In addi-tion,TSP samples were also synchronously daily collected by medium-volume samplers with Whatman41 filters in the spring of 2007.BC in the dust aerosol was up to 1.14%of the total mass of PM10.A remarkable seasonal variation of BC in the aerosol was observed in the order of winter>spring>autumn>summer.The peak value of BC appeared at midnight while the lowest one in the evening each day,which was just the reverse of that in the urban area.The contribution of BC to the total mass of PM10 on non-dust storm days was~11 times of that in dust storm.Through back trajectory and principal component analysis,it was found that BC in the dust aerosol over Taklimakan Desert might be attributed to the emission from the anthropogenic activities,including domestic heating,cooking,combustion of oil and natural gas,and the medium-range transport from those oases located in the margins of the desert.The total BC aerosol from the Taklimakan Desert to be transported to the eastward downstream was estimated to be 6.3×104 ton yr-1.

  14. Factors controlling seasonal variations in Arctic black carbon

    Science.gov (United States)

    Shen, Z.; Ming, Y.; Horowitz, L. W.

    2015-12-01

    Arctic haze has a distinct seasonality with higher concentrations in winter and spring. This study evaluates how different processes of large-scale circulation and removal control seasonal variations in Arctic black carbon (BC) using the Geophysical Fluid Dynamics Laboratory (GFDL) atmospheric general circulation model (AM3). We find that transport and wet deposition play unequal roles in determining Arctic BC seasonal cycle. Despite seasonal differences in general circulation patterns, the eddy-driven BC transport changes little throughout the year, and the seasonal cycle of Arctic BC is attributed to wet removal. BC hydrophilic fraction affected by the aging process and hydrophilic BC (BCpi) wet deposition rate affected by cloud microphysics determine wet deposition. Both low hydrophilic fraction and low wet deposition rate account for the peak of BC in winter. The transition to low BC in summer results from an increase in wet deposition rate, while the return of BC in late autumn is mainly caused by a sharp decrease in hydrophilic fraction. The results suggest that the concentrations of Arctic aerosols as well as their climate impacts may be susceptible to modification in a future climate.

  15. Black Carbon in Seasonal Snow across Northern Xinjiang, Northwestern China

    Science.gov (United States)

    Ye, H.; Zhang, R.; Shi, J.; Huang, J.; Warren, S. G.; Fu, Q.

    2012-12-01

    Black carbon (BC) particles in snow can significantly reduce the snow albedo and enhance the absorption of solar radiation, with important impacts on climate and the hydrological cycle. A field campaign was carried out to measure the BC content in seasonal snow in Qinghai and Xinjiang provinces of western China, in January and February, 2012. About 300 snow samples were collected at 38 sites, 6 in Qinghai and 32 in Xinjiang. The observational results at the sites in Xinjiang, where the dominant absorbing impurities in snow are BC particles, are reported in this paper. The BC mass-fractions in seasonal snow across northern Xinjiang have a median value of ~70 ng/g, lower than those in northeast China but comparable to those in snow on glaciers of the Tianshan Mountains. The estimated concentration of BC at the cleanest site in Xinjiang is 20 ng/g, which is similar to that found along the coast of the Arctic Ocean. In general, the BC content of snow decreases with altitude. The data from this field campaign should be useful for testing transport models and climate models for the simulated BC in snow.

  16. Black carbon absorption effects on cloud cover, review and synthesis

    Directory of Open Access Journals (Sweden)

    D. Koch

    2010-03-01

    Full Text Available Absorbing aerosols (AA's such as black carbon (BC or dust absorb incoming solar radiation, perturb the temperature structure of the atmosphere, and influence cloud cover. Previous studies have described conditions where AA's either increase or decrease cloud cover. The effect depends on several factors, including the altitude of the AA relative to the cloud and on the cloud type. Cloud cover is decreased if the AA's are embedded in the cloud layer. AA's below cloud may enhance convection and cloud cover. AA's over cloud-level stabilize the underlying layer and tend to enhance stratocumulus clouds but may reduce cumulus clouds. AA's can also promote cloud cover in convergent regions as they enhance deep convection and low level convergence as it draws in moisture from ocean to land regions. Most global model studies indicate a regional variation in the cloud response but generally increased cloud cover over oceans and some land regions, with net increased low-level and/or reduced upper level cloud cover. The result is net negative radiative forcing from cloud response to AA's. In some of these climate model studies, the cooling effect of BC due to cloud changes was strong enough to essentially cancel the warming direct effects.

  17. Black carbon aerosols and the third polar ice cap

    Energy Technology Data Exchange (ETDEWEB)

    Menon, Surabi; Koch, Dorothy; Beig, Gufran; Sahu, Saroj; Fasullo, John; Orlikowski, Daniel

    2010-04-15

    Recent thinning of glaciers over the Himalayas (sometimes referred to as the third polar region) have raised concern on future water supplies since these glaciers supply water to large river systems that support millions of people inhabiting the surrounding areas. Black carbon (BC) aerosols, released from incomplete combustion, have been increasingly implicated as causing large changes in the hydrology and radiative forcing over Asia and its deposition on snow is thought to increase snow melt. In India BC emissions from biofuel combustion is highly prevalent and compared to other regions, BC aerosol amounts are high. Here, we quantify the impact of BC aerosols on snow cover and precipitation from 1990 to 2010 over the Indian subcontinental region using two different BC emission inventories. New estimates indicate that Indian BC emissions from coal and biofuel are large and transport is expected to expand rapidly in coming years. We show that over the Himalayas, from 1990 to 2000, simulated snow/ice cover decreases by {approx}0.9% due to aerosols. The contribution of the enhanced Indian BC to this decline is {approx}36%, similar to that simulated for 2000 to 2010. Spatial patterns of modeled changes in snow cover and precipitation are similar to observations (from 1990 to 2000), and are mainly obtained with the newer BC estimates.

  18. Factorial Based Response Surface Modeling with Confidence Intervals for Optimizing Thermal Optical Transmission Analysis of Atmospheric Black Carbon

    Science.gov (United States)

    We demonstrate how thermal-optical transmission analysis (TOT) for refractory light-absorbing carbon in atmospheric particulate matter was optimized with empirical response surface modeling. TOT employs pyrolysis to distinguish the mass of black carbon (BC) from organic carbon (...

  19. The Influence of Unidirectional Pressure on Electrical Conductivity of Carbon Black Filled Polyethylene

    Institute of Scientific and Technical Information of China (English)

    WANG Ke; ZHANG Guo; ZHAO Zhudi; PENG Yi; DI Weihua; DU Chuang

    2006-01-01

    High density polyethylene filled with conductive carbon black was prepared by conventional melt-mixing method. The effect of unidirectional pressure on the conductivity was studied. Wide angle X-ray diffraction (WAXD) was used to show the influence of pressure on the aggregate structure of the polymer filled with carbon black (CB) fillers. A model on the basis of the formation and destruction of conductive networks was proposed to explain the change in the conductivity with the application of pressure.

  20. Sources of uncertainties in modelling black carbon at the global scale

    OpenAIRE

    2010-01-01

    Our understanding of the global black carbon (BC) cycle is essentially qualitative due to uncertainties in our knowledge of its properties. This work investigates two source of uncertainties in modelling black carbon: those due to the use of different schemes for BC ageing and its removal rate in the global Transport-Chemistry model TM5 and those due to the uncertainties in the definition and quantification of the observations, which propagate through to both the emission inventories, and the...

  1. Computing black hole partition functions from quasinormal modes

    CERN Document Server

    Arnold, Peter; Vaman, Diana

    2016-01-01

    We propose a method of computing one-loop determinants in black hole spacetimes (with emphasis on asymptotically anti-de Sitter black holes) that may be used for numerics when completely-analytic results are unattainable. The method utilizes the expression for one-loop determinants in terms of quasinormal frequencies determined by Denef, Hartnoll and Sachdev in [1]. A necessary ingredient is a refined regularization scheme to regulate the contributions of individual fixed-momentum sectors to the partition function. To this end, we formulate an effective two-dimensional problem in which a natural refinement of standard heat kernel techniques can be used to account for contributions to the partition function at fixed momentum. We test our method in a concrete case by reproducing the scalar one-loop determinant in the BTZ black hole background. We then discuss the application of such techniques to more complicated spacetimes.

  2. Selection and Characterization of Carbon Black and Surfactants for Development of Small Scale Uranium Oxicarbide Kernels

    Energy Technology Data Exchange (ETDEWEB)

    Contescu, Cristian I [ORNL

    2006-01-01

    This report supports the effort for development of small scale fabrication of UCO (a mixture of UO{sub 2} and UC{sub 2}) fuel kernels for the generation IV high temperature gas reactor program. In particular, it is focused on optimization of dispersion conditions of carbon black in the broths from which carbon-containing (UO{sub 2} {center_dot} H{sub 2}O + C) gel spheres are prepared by internal gelation. The broth results from mixing a hexamethylenetetramine (HMTA) and urea solution with an acid-deficient uranyl nitrate (ADUN) solution. Carbon black, which is previously added to one or other of the components, must stay dispersed during gelation. The report provides a detailed description of characterization efforts and results, aimed at identification and testing carbon black and surfactant combinations that would produce stable dispersions, with carbon particle sizes below 1 {micro}m, in aqueous HMTA/urea and ADUN solutions. A battery of characterization methods was used to identify the properties affecting the water dispersability of carbon blacks, such as surface area, aggregate morphology, volatile content, and, most importantly, surface chemistry. The report introduces the basic principles for each physical or chemical method of carbon black characterization, lists the results obtained, and underlines cross-correlations between methods. Particular attention is given to a newly developed method for characterization of surface chemical groups on carbons in terms of their acid-base properties (pK{sub a} spectra) based on potentiometric titration. Fourier-transform infrared (FTIR) spectroscopy was used to confirm the identity of surfactants, both ionic and non-ionic. In addition, background information on carbon black properties and the mechanism by which surfactants disperse carbon black in water is also provided. A list of main physical and chemical properties characterized, samples analyzed, and results obtained, as well as information on the desired trend or

  3. Global emission inventory and atmospheric transport of black carbon. Evaluation of the associated exposure

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Rong

    2015-06-01

    This thesis presents research focusing on the improvement of high-resolution global black carbon (BC) emission inventory and application in assessing the population exposure to ambient BC. A particular focus of the thesis is on the construction of a high-resolution (both spatial and sectorial) fuel consumption database, which is used to develop the emission inventory of black carbon. Above all, the author updates the global emission inventory of black carbon, a resource subsequently used to study the atmospheric transport of black carbon over Asia with the help of a high-resolution nested model. The thesis demonstrates that spatial bias in fuel consumption and BC emissions can be reduced by means of the sub-national disaggregation approach. Using the inventory and nested model, ambient BC concentrations can be better validated against observations. Lastly, it provides a complete uncertainty analysis of global black carbon emissions, and this uncertainty is taken into account in the atmospheric modeling, helping to better understand the role of black carbon in regional and global air pollution.

  4. Challenges for Reducing Emissions of Black Carbon from the Transport Sector in Urban Areas

    Science.gov (United States)

    Zavala, M. A.; Molina, L. T.

    2013-05-01

    The transport sector is a large contributor of harmful gaseous and particulate emissions in many urban areas. Black carbon is a component of short-lived particulate matter emitted predominantly by freight, public transport, and heavy- duty trucks. Controlling the emissions of black carbon from the transport sector is important for mitigating its impacts on climate, ecosystems, and human health. However, reducing the emissions of black carbon from mobile sources may be a challenging task in many developing urban areas due to economic, social, and technical constrains. Several emissions control technologies offer a proven approach for reducing emissions of black carbon from diesel-powered mobile sources, but the accurate quantification of associated emissions benefits in developing urban areas is not well documented. We describe recent advances for the estimation of black carbon emissions from the transport sector in real world driving conditions and present examples of the potential benefits of implementing various emission control technologies in Mexico. The results can help in the identification of key factors that hinder the implementation of control emissions for reducing emissions of black carbon elsewhere.

  5. Measurement of Black Carbon and Co-pollutants Emitted from Diesel Vehicles in Mexico

    Science.gov (United States)

    Zavala, M. A.; Molina, L. T.; Fortner, E.; Herndon, S.; Knighton, B.; Yacovitch, T. I.; Floerchinger, C. R.; Roscioli, J. R.; Kolb, C. E.; Paramo, V. H.; Zirath, S.; Mejia, J.; Jazcilevich, A. D.

    2013-12-01

    Freight, public transport, and heavy-duty trucks can contribute to harmful emissions of black carbon and other co-pollutants in many urban areas. Controlling the emissions of black carbon from the transport sector is important for the potential of mitigating its impacts on climate, ecosystems, and human health. However, reducing the emissions of black carbon from mobile sources is be a challenging task in many developing urban areas due to economic, social, and technical constrains, as well as the uncertainties surrounding the accurate quantification of the associated benefits. Several emissions control technologies offer a proven approach for reducing emissions of black carbon from diesel-powered mobile sources, but the accurate quantification of associated emissions benefits in developing urban areas is not well documented. We present the results of the measurement of black carbon and co-emitted pollutants of dozens of diesel powered vehicles, including freight trucks, public transport buses, and intra-city metrobuses sampled during a 4-day experiment in Mexico City in February of 2013 as part of the SLCFs-Mexico project. Measurements were obtained with the Aerodyne Mobile Laboratory, remote sensing, and portable emissions measurements, and encompassed the sampling of several vehicle models and technologies in experimental and real-world driving conditions. The results can help in the identification of key factors that hinder the implementation of control emissions for reducing emissions of black carbon elsewhere and the potential benefits of implementing various emission control technologies.

  6. The nature of carbon material in the black shale rock mass of Kazakhstan

    Energy Technology Data Exchange (ETDEWEB)

    Marchenko, L.G.

    1981-01-01

    Carbon material is closely tied to ores of various origin lying in the carbon (black shale) rock masses of Kazakhastan. The nature of the carbon material in several gold fields is closely examined. Shungite, its paragenesis with ore materials and its role in the carbon and ore material processes, is described. The accumulation of shungite in zones determined to consist of ores, is looked at in terms of prospecting criteria.

  7. Analyzing 20 years of Black Carbon measurements in Germany

    Science.gov (United States)

    Kutzner, R. D.; Quedenau, J.; Kuik, F.; von Schneidemesser, E.; Schmale, J.

    2016-12-01

    Black Carbon (BC) is an important short-lived climate-forcing pollutant contributing to global warming through absorption of sunlight. In addition, BC, as a component of particulate matter (PM) exerts adverse health effects. Anthropogenic emission sources of BC include residential heating, transport, and agricultural fires, and the dominant natural emission source is wildfires. Despite the adverse effects of BC, legislation that requires mandatory monitoring of BC concentrations does not currently exist in the European Union (EU). Instead, BC is only indirectly monitored as component of PM10 and PM2.5 (PM with a diameter smaller 10 µm and 2.5 µm, respectively). Before the introduction of mandatory PM10 and PM2.5 monitoring in the EU in 2005 and 2015, respectively, `black smoke' (BS), a surrogate for BC, was a required measurement in Germany from the early 1990s. The annual mean limit value was 14 µg/m3 from 1995 and 8 µg/m³ from 1998. In 2004, many measurements were stopped, with the repeal of the regulations. In most German federal states a limited number BC monitoring stations continued to operate. We present a synthesis of BC data from 213 stations across Germany covering the period between 1994 and 2014. Due to the lack of a standardized method and respective legislation, the data set is very heterogeneous relying on twelve different measurement methods including chemical, optical, and thermal-optical methods. Stations include, among others, urban background, traffic and rural. We highlight results from the year 2009, as it is the year with the largest measurement coverage based on the same measurement method, with 28 stations. Further, we calculated trends in BC concentrations for 13 stations with at least 10 years of data, for median concentrations, as well as 5th percentile (background) and 95th percentile (peak episodes). Preliminary results suggest that concentrations have generally declined, with a larger trend at traffic stations compared to urban

  8. Are emissions of black carbon from gasoline vehicles overestimated? Real-time, in situ measurement of black carbon emission factors.

    Science.gov (United States)

    Wang, Yang; Xing, Zhenyu; Zhao, Shuhui; Zheng, Mei; Mu, Chao; Du, Ke

    2016-03-15

    Accurately quantifying black carbon (BC) emission factors (EFs) is a prerequisite for estimation of BC emission inventory. BC EFs determined by measuring BC at the roadside or chasing a vehicle on-road may introduce large uncertainty for low emission vehicles. In this study, BC concentrations were measured inside the tailpipe of gasoline vehicles with different engine sizes under different driving modes to determine the respective EFs. BC EFs ranged from 0.005-7.14 mg/kg-fuel under the speeds of 20-70 km/h, 0.05-28.95 mg/kg-fuel under the accelerations of 0.5-1.5m/s(2). Although the water vapor in the sampling stream could result in an average of 12% negative bias, the BC EFs are significantly lower than the published results obtained with roadside or chasing vehicle measurement. It is suggested to conduct measurement at the tailpipe of gasoline vehicles instead of in the atmosphere behind the vehicles to reduce the uncertainty from fluctuation in ambient BC concentration. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Family Disruption and Academic Functioning in Urban, Black Youth

    Science.gov (United States)

    Somers, Cheryl L.; Chiodo, Lisa M.; Yoon, Jina; Ratner, Hilary; Barton, Elizabeth; Delaney-Black, Virginia

    2011-01-01

    The purpose of this study was to examine from an ecological perspective the relationships between multiple levels of family disruption and children's academic functioning in a sample of 390 urban, Black adolescents at age 14. Subjects in this cohort have been followed longitudinally since before their birth. Data from previous assessments at birth…

  10. Probing Black Carbon-containing Particle Microphysics with the Single-Particle Soot Photometer (SP2)

    Science.gov (United States)

    Sedlacek, A. J.; Lewis, E. R.; Onasch, T. B.; Lambe, A. T.; Davidovits, P.; Kleinman, L. I.

    2012-12-01

    Knowledge of the structure and mixing state of black-carbon containing particles is important for calculating their radiative forcing and provides insight into their source and life cycle. Recently analysis of black carbon-containing particles has demonstrated that for a fraction of such particles, the black carbon may reside on or near the surface of the particle as opposed to the traditional core-shell configuration typically assumed in which the black carbon core is surrounded by a shell of non-refractory material. During the DOE-sponsored Aerosol Lifecycle field campaign held in summer, 2011 at Brookhaven National Laboratory on Long Island, NY, episodes were encountered in which a high fraction of particles containing black carbon had such configurations, and these episodes corresponded to air masses that contained biomass burning plumes (Sedlacek et al., 2012). Subsequent analysis found other episodes in field campaigns in Colorado and California in which high fractions this configuration corresponded to biomass burning plumes. In an effort to evaluate this interpretation and explore formation mechanisms, a series of laboratory-based experiments examining the coagulation of regal black (surrogate for collapsed soot) with model non-refractory coatings [dioctyl sebacate (surrogate for organic aerosols with liquid-like character) and deliquesced ammonium sulfate (solid)] were carried out. The results of these experiments and their potential implications on black carbon radiative forcing will be discussed. Sedlacek, III, Arthur, E. R. Lewis, L. I. Kleinman, J. Xu and Q. Zhang (2012), Determination of and Evidence for Non-core-shell structure of particles containing black carbon using the single particle soot photometer (SP2). Geophys. Res. Lett., 39 L06802, doi:10.1029/2012GL050905

  11. Pseudo-capacitance of ruthenium oxide/carbon black composites for electrochemical capacitors

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Hydrous ruthenium oxide was formed by a new process.The precursor was obtained by mixing the aqueous solutions of RuCl3·xH20 and NaHCO3.The addition of NaHCO3 led to the formation of an oxide with extremely free RuO2 particles forming a porous network structure in the oxide electrode.Polyethylene glycol was added as a controller to partly inhibit the sol-gel reaction.The rate capacitance of 530 F·g-1 was measured for the powder formed at an optimal annealing temperature of 210~C.Several details concerning this new material,including crystal structure,particle size as a function of temperature,and electrochemical properties,were also reported.In addition,the rote capacitance of the composite electrode reached 800 F·g-1 after carbon black was added.By using the modified electrode of a RuO2/carbon black composite electrode,the electrochemical capacitor exhibits high energy density and stable power characteristics.The values of specific energy and maximum specific power of 24 Wh·kg-1 and 4 kW·kg-1,respectively,are demonstrated for a cell voltage between 0 and 1 V.

  12. Piezoresistive strain sensing of carbon black /silicone composites above percolation threshold.

    Science.gov (United States)

    Shang, Shuying; Yue, Yujuan; Wang, Xiaoer

    2016-12-01

    A series of flexible composites with a carbon black (CB) filled silicone rubber matrix were made by an improved process in this work. A low percolation threshold with a mass ratio of 2.99% CB was achieved. The piezoresistive behavior of CB/silicone composites above the critical value, with the mass ratio of carbon black to the silicone rubber ranging from 0.01 to 0.2, was studied. The piezoresistive behavior was different from each other for the composites with different CB contents. But, the composites show an excellent repeatability of piezoresistivity under cyclic compression, no matter with low filler content or with high filler content. The most interesting phenomena were that the plots of gauge factor versus strain of the composites with different CB contents constructed a master curve and the curve could be well fitted by a function. It was showed that the gauge factor of the composites was strain-controlled showing a promising prospect of application.

  13. Surface modification of carbon black for the reinforcement of polycarbonate/acrylonitrile–butadiene–styrene blends

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, B.B. [School of Chemical Engineering, Fuzhou University, Fuzhou 350108 (China); Chen, Y. [School of materials Engineering, Fujian Agriculture and Forestry University, Fuzhou 350002 (China); Wang, F. [School of Chemical Engineering, Fuzhou University, Fuzhou 350108 (China); Hong, R.Y., E-mail: rhong@suda.edu.cn [School of Chemical Engineering, Fuzhou University, Fuzhou 350108 (China); College of Chemistry, Chemical Engineering and Materials Science & Key Laboratory of Organic Synthesis of Jiangsu Province, Soochow University, SIP, Suzhou 215123 (China)

    2015-10-01

    Highlights: • CB was modified through the method of oxygen plasma treatment. • Surface modified CB applied in PC/ABS blends. • The treated CB showed better compatibility in PC/ABS blends. • PC/ABS blends with treated CB showed better mechanical and thermal properties. - Abstract: The surface of carbon black was modified by oxygen plasma treatment for different times (10, 20 and 30 min). In order to increase the applicability of carbon black (CB), functional groups were grafted on the generally inert surface of CB using oxygen plasma. The surface compositional and structural changes that occurred on CB were investigated by SEM, FT-IR, Raman spectroscopy, XRD and BET. Subsequently, CB reinforced polycarbonate (PC)/acrylonitrile-butadiene-styrene (ABS) composites were prepared by internal batch mixing with the addition of different content of CB (3, 6, 9, 12 wt%). The morphology of PC/ABS/CB (7/3/6 wt%) nanocomposites was studied through scanning electron microscopy. Observations of SEM images showed that the plasma-treated CB had a better dispersion in the blend matrix. Moreover, the mechanical tests showed that the tensile strength and impact strength were improved by 32.4% and 22.5%, respectively, with the addition of plasma-treated CB. In addition, the thermal stability was improved and glass transition temperatures of both PC and ABS increased as shown by TGA and DSC, respectively.

  14. Impacts of black carbon and co-pollutant emissions from transportation sector in Mexico City

    Science.gov (United States)

    Zavala, Miguel; Almanza, Victor; Garcia, Agustin; Jazcilevich, Aron; Lei, Wenfang; Molina, Luisa

    2016-04-01

    Black carbon is one of the most important short-lived climate-forcing agents, which is harmful to human health and also contributes significantly to climate change. Transportation is one of the largest sources of black carbon emissions in many megacities and urban complexes, with diesel vehicles leading the way. Both on-road and off-road vehicles can emit substantial amounts of harmful BC-containing particulate matter (PM) and are also responsible for large emissions of carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), and many other co-emitted volatile organic compounds (VOCs). Regionally, black carbon emissions contributions from mobile sources may vary widely depending on the technical characteristics of the vehicle fleet, the quality and chemical properties of the fuels consumed, and the degree of local development and economic activities that foster wider and more frequent or intensive use of vehicles. This presentation will review and assess the emissions of black carbon from the on-road and off-road transportation sector in the Mexico City Metropolitan Area. Viable mitigation strategies, including innovative technological alternatives to reduce black carbon and co-pollutants in diesel vehicles and their impacts on climate, human health and ecosystems will be described.

  15. Sources of uncertainties in modelling black carbon at the global scale

    Directory of Open Access Journals (Sweden)

    E. Vignati

    2010-03-01

    Full Text Available Our understanding of the global black carbon (BC cycle is essentially qualitative due to uncertainties in our knowledge of its properties. This work investigates two source of uncertainties in modelling black carbon: those due to the use of different schemes for BC ageing and its removal rate in the global Transport-Chemistry model TM5 and those due to the uncertainties in the definition and quantification of the observations, which propagate through to both the emission inventories, and the measurements used for the model evaluation.

    The schemes for the atmospheric processing of black carbon that have been tested with the model are (i a simple approach considering BC as bulk aerosol and a simple treatment of the removal with fixed 70% of in-cloud black carbon concentrations scavenged by clouds and removed when rain is present and (ii a more complete description of microphysical ageing within an aerosol dynamics model, where removal is coupled to the microphysical properties of the aerosol, which results in a global average of 40% in-cloud black carbon that is scavenged in clouds and subsequently removed by rain, thus resulting in a longer atmospheric lifetime. This difference is reflected in comparisons between both sets of modelled results and the measurements. Close to the sources, both anthropogenic and vegetation fire source regions, the model results do not differ significantly, indicating that the emissions are the prevailing mechanism determining the concentrations and the choice of the aerosol scheme does not influence the levels. In more remote areas such as oceanic and polar regions the differences can be orders of magnitude, due to the differences between the two schemes. The more complete description reproduces the seasonal trend of the black carbon observations in those areas, although not always the magnitude of the signal, while the more simplified approach underestimates black carbon concentrations by orders of

  16. Sources of uncertainties in modelling black carbon at the global scale

    Science.gov (United States)

    Vignati, E.; Karl, M.; Krol, M.; Wilson, J.; Stier, P.; Cavalli, F.

    2010-03-01

    Our understanding of the global black carbon (BC) cycle is essentially qualitative due to uncertainties in our knowledge of its properties. This work investigates two source of uncertainties in modelling black carbon: those due to the use of different schemes for BC ageing and its removal rate in the global Transport-Chemistry model TM5 and those due to the uncertainties in the definition and quantification of the observations, which propagate through to both the emission inventories, and the measurements used for the model evaluation. The schemes for the atmospheric processing of black carbon that have been tested with the model are (i) a simple approach considering BC as bulk aerosol and a simple treatment of the removal with fixed 70% of in-cloud black carbon concentrations scavenged by clouds and removed when rain is present and (ii) a more complete description of microphysical ageing within an aerosol dynamics model, where removal is coupled to the microphysical properties of the aerosol, which results in a global average of 40% in-cloud black carbon that is scavenged in clouds and subsequently removed by rain, thus resulting in a longer atmospheric lifetime. This difference is reflected in comparisons between both sets of modelled results and the measurements. Close to the sources, both anthropogenic and vegetation fire source regions, the model results do not differ significantly, indicating that the emissions are the prevailing mechanism determining the concentrations and the choice of the aerosol scheme does not influence the levels. In more remote areas such as oceanic and polar regions the differences can be orders of magnitude, due to the differences between the two schemes. The more complete description reproduces the seasonal trend of the black carbon observations in those areas, although not always the magnitude of the signal, while the more simplified approach underestimates black carbon concentrations by orders of magnitude. The sensitivity to wet

  17. Estimates of increased black carbon emissions from electrostatic precipitators during powdered activated carbon injection for mercury emissions control.

    Science.gov (United States)

    Clack, Herek L

    2012-07-03

    The behavior of mercury sorbents within electrostatic precipitators (ESPs) is not well-understood, despite a decade or more of full-scale testing. Recent laboratory results suggest that powdered activated carbon exhibits somewhat different collection behavior than fly ash in an ESP and particulate filters located at the outlet of ESPs have shown evidence of powdered activated carbon penetration during full-scale tests of sorbent injection for mercury emissions control. The present analysis considers a range of assumed differential ESP collection efficiencies for powdered activated carbon as compared to fly ash. Estimated emission rates of submicrometer powdered activated carbon are compared to estimated emission rates of particulate carbon on submicrometer fly ash, each corresponding to its respective collection efficiency. To the extent that any emitted powdered activated carbon exhibits size and optical characteristics similar to black carbon, such emissions could effectively constitute an increase in black carbon emissions from coal-based stationary power generation. The results reveal that even for the low injection rates associated with chemically impregnated carbons, submicrometer particulate carbon emissions can easily double if the submicrometer fraction of the native fly ash has a low carbon content. Increasing sorbent injection rates, larger collection efficiency differentials as compared to fly ash, and decreasing sorbent particle size all lead to increases in the estimated submicrometer particulate carbon emissions.

  18. Cellphones as a Distributed Platform for Black Carbon Data Collection

    Science.gov (United States)

    Ramanathan, N.; Ramana, M.; Lukac, M. L.; Siva, P.; Ahmed, T.; Kar, A.; Rehman, I.; Ramanathan, V.

    2010-12-01

    Black carbon (BC), the visible component of soot that gives emissions such as diesel engine exhaust their dark color, has come to be recognized as a major contributor to global warming, and a frontline concern for climate change strategies (Ramanathan 2001, Jacobson 2010). We have developed a new low-cost instrument for gathering and measuring atmospheric BC concentrations that leverages cellphones to transmit data from an air filtration unit to a centralized database for analysis. Our new system relies on image processing techniques, as opposed to other more expensive optical methods, to interpret images of filters captured with a cellphone camera. As a result, the entire system costs less than $500 (and is orders of magnitude cheaper than an Aethalometer, the prevailing method for measuring atmospheric BC). We are working with three community groups in Los Angeles, and will recruit three groups in the San Francisco Bay Area, to enable 40 citizens to be actively engaged in monitoring BC across California. We are working with The Energy Resources Institute, an international NGO based in India, to deploy this instrument with 60 people in conjunction with Project Surya, which aims to deploy clean cookstoves and rigorously evaluate their impact on BC emissions. Field tests of this new instrument performed in California report an average error of 0.28 µg/m3 when compared with an Aethelometer. These excellent results hold the promise of making large-scale data collection of BC feasible and relatively easy to reproduce (Ramanathan et al., forthcoming). The use of cellphones for data collection permits monitoring of BC to occur on a greater, more comprehensive scale not previously possible, and serves as a means of instituting more precise, variation-sensitive evaluations of emissions. By storing the data in a publicly available repository, our system will provide real-time access to mass-scale BC measurements to researchers and the public. Through our pilot

  19. Cosmological Evolution of Supermassive Black Holes: Mass Functions and Spins

    CERN Document Server

    Li, Yan-Rong; Ho, Luis C

    2012-01-01

    We derive the mass function of supermassive black holes (SMBHs) over the redshift range 0functions of field galaxies. Applying this mass function, combined with the bolometric luminosity function of active galactic nuclei (AGNs), into the the continuity equation of SMBH number density, we explicitly obtain the mass-dependent cosmological evolution of the radiative efficiency for accretion. We suggest that the accretion history of SMBHs and their spins evolve in two distinct regimes: an early phase of prolonged accretion, plausibly driven by major mergers, during which the black hole spins up, then switching to a period of random, episodic accretion, governed by minor mergers and internal secular processes, during which the hole spins down. The transition epoch depends on mass, mirroring other evidence for "cosmic downsizing" in the AGN population.

  20. Climate Response of Direct Radiative Forcing of Anthropogenic Black Carbon

    Science.gov (United States)

    Chung, Serena H.; Seinfeld,John H.

    2008-01-01

    The equilibrium climate effect of direct radiative forcing of anthropogenic black carbon (BC) is examined by 100-year simulations in the Goddard Institute for Space Studies General Circulation Model II-prime coupled to a mixed-layer ocean model. Anthropogenic BC is predicted to raise globally and annually averaged equilibrium surface air temperature by 0.20 K if BC is assumed to be externally mixed. The predicted increase is significantly greater in the Northern Hemisphere (0.29 K) than in the Southern Hemisphere (0.11 K). If BC is assumed to be internally mixed with the present day level of sulfate aerosol, the predicted annual mean surface temperature increase rises to 0.37 K globally, 0.54 K for the Northern Hemisphere, and 0.20 K for the Southern Hemisphere. The climate sensitivity of BC direct radiative forcing is calculated to be 0.6 K W (sup -1) square meters, which is about 70% of that of CO2, independent of the assumption of BC mixing state. The largest surface temperature response occurs over the northern high latitudes during winter and early spring. In the tropics and midlatitudes, the largest temperature increase is predicted to occur in the upper troposphere. Direct radiative forcing of anthropogenic BC is also predicted to lead to a change of precipitation patterns in the tropics; precipitation is predicted to increase between 0 and 20 N and decrease between 0 and 20 S, shifting the intertropical convergence zone northward. If BC is assumed to be internally mixed with sulfate instead of externally mixed, the change in precipitation pattern is enhanced. The change in precipitation pattern is not predicted to alter the global burden of BC significantly because the change occurs predominantly in regions removed from BC sources.

  1. Radiative absorption enhancement from coatings on black carbon aerosols

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Xinjuan; Wang, Xinfeng; Yang, Lingxiao [Environmental Research Institute, School of Environmental Science and Engineering, Shandong University, Jinan 250100 (China); Chen, Bing, E-mail: bingchen@sdu.edu.cn [Environmental Research Institute, School of Environmental Science and Engineering, Shandong University, Jinan 250100 (China); Chen, Jianmin, E-mail: jmchen@sdu.edu.cn [Environmental Research Institute, School of Environmental Science and Engineering, Shandong University, Jinan 250100 (China); Andersson, August; Gustafsson, Örjan [Department of Environmental Science and Analytical Chemistry (ACES) and the Bolin Centre for Climate Research, Stockholm University, SE-10691 Stockholm (Sweden)

    2016-05-01

    The radiative absorption enhancement of ambient black carbon (BC), by light-refractive coatings of atmospheric aerosols, constitutes a large uncertainty in estimates of climate forcing. The direct measurements of radiative absorption enhancement require the experimentally-removing the coating materials in ambient BC-containing aerosols, which remains a challenge. Here, the absorption enhancement of the BC core by non-absorbing aerosol coatings was quantified using a two-step removal of both inorganic and organic matter coatings of ambient aerosols. The mass absorption cross-section (MAC) of decoated/pure atmospheric BC aerosols of 4.4 ± 0.8 m{sup 2}g{sup −1} was enhanced to 9.6 ± 1.8 m{sup 2}g{sup −1} at 678-nm wavelength for ambiently-coated BC aerosols at a rural Northern China site. The enhancement of MAC (E{sub MAC}) rises from 1.4 ± 0.3 in fresh combustion emissions to ~ 3 for aged ambient China aerosols. The three-week high-intensity campaign observed an average E{sub MAC} of 2.25 ± 0.55, and sulfates were primary drivers of the enhanced BC absorption. - Highlights: • A method was developed to remove coatings surrounding BC in ambient aerosols. • The MAC of decoated BC of 4.4 was enhanced to 9.6 m{sup 2}g{sup −1} for ambient BC aerosols. • BC radiative forcing in the ambient atmosphere was enhanced by a factor of ~ 2. • BC absorption enhancement peaked in day time driven by secondary sulfate.

  2. Increased fire frequency optimization of black carbon mixing and storage

    Science.gov (United States)

    Pyle, Lacey; Masiello, Caroline; Clark, Kenneth

    2016-04-01

    Soil carbon makes up a substantial part of the global carbon budget and black carbon (BC - produced from incomplete combustion of biomass) can be significant fraction of soil carbon. Soil BC cycling is still poorly understood - very old BC is observed in soils, suggesting recalcitrance, yet in short term lab and field studies BC sometimes breaks down rapidly. Climate change is predicted to increase the frequency of fires, which will increase global production of BC. As up to 80% of BC produced in wildfires can remain at the fire location, increased fire frequency will cause significant perturbations to soil BC accumulation. This creates a challenge in estimating soil BC storage, in light of a changing climate and an increased likelihood of fire. While the chemical properties of BC are relatively well-studied, its physical properties are much less well understood, and may play crucial roles in its landscape residence time. One important property is density. When BC density is less than 1 g/cm3 (i.e. the density of water), it is highly mobile and can easily leave the landscape. This landscape mobility following rainfall may inflate estimates of its degradability, making it crucial to understand both the short- and long term density of BC particles. As BC pores fill with minerals, making particles denser, or become ingrown with root and hyphal anchors, BC is likely to become protected from erosion. Consequently, how quickly BC is mixed deeper into the soil column is likely a primary controller on BC accumulation. Additionally the post-fire recovery of soil litter layers caps BC belowground, protecting it from erosional forces and re-combustion in subsequent fires, but still allowing bioturbation deeper into the soil column. We have taken advantage of a fire chronosequence in the Pine Barrens of New Jersey to investigate how density of BC particles change over time, and how an increase in fire frequency affects soil BC storage and soil column movement. Our plots have

  3. Atmospheric black carbon and sulfate concentrations in Northeast Greenland

    Science.gov (United States)

    Massling, A.; Nielsen, I. E.; Kristensen, D.; Christensen, J. H.; Sørensen, L. L.; Jensen, B.; Nguyen, Q. T.; Nøjgaard, J. K.; Glasius, M.; Skov, H.

    2015-08-01

    Measurements of equivalent black carbon (EBC) in aerosols at the high Arctic field site Villum Research Station (VRS) at Station Nord in North Greenland showed a seasonal variation in EBC concentrations with a maximum in winter and spring at ground level. Average measured concentrations were about 0.067 ± 0.071 for the winter and 0.011 ± 0.009 for the summer period. These data were obtained using a multi-angle absorption photometer (MAAP). A similar seasonal pattern was found for sulfate concentrations with a maximum level during winter and spring analyzed by ion chromatography. Here, measured average concentrations were about 0.485 ± 0.397 for the winter and 0.112 ± 0.072 for the summer period. A correlation between EBC and sulfate concentrations was observed over the years 2011 to 2013 stating a correlation coefficient of R2 = 0.72. This finding gives the hint that most likely transport of primary emitted BC particles to the Arctic was accompanied by aging of the aerosols through condensational processes. BC and sulfate are known to have only partly similar sources with respect to their transport pathways when reaching the high Arctic. Aging processes may have led to the formation of secondary inorganic matter and further transport of BC particles as cloud processing and further washout of particles is less likely based on the typically observed transport patterns of air masses arriving at VRS. Additionally, concentrations of EC (elemental carbon) based on a thermo-optical method were determined and compared to EBC measurements. EBC measurements were generally higher, but a correlation between EC and EBC resulted in a correlation coefficient of R2 = 0.64. Model estimates of the climate forcing due to BC in the Arctic are based on contributions of long-range transported BC during spring and summer. The measured concentrations were here compared with model results obtained by the Danish Eulerian Hemispheric Model, DEHM. Good agreement between measured and

  4. Fluvial organic carbon losses from a Bornean black water river

    OpenAIRE

    2010-01-01

    The transport of carbon from terrestrial ecosystems such as peatlands into rivers and out to the oceans plays an important role in the carbon cycle because it provides a link between the terrestrial and marine carbon cycles. Concentrations of dissolved organic carbon (DOC) and particulate organic carbon (POC) were analysed from the source to the mouth of the River Sebangau in Central Kalimantan, Indonesia during the dry and wet seasons in 2008/2009 and an annual total organic carbon (TOC) flu...

  5. Comparison of manufactured and black carbon nanoparticle concentrations in aquatic sediments

    NARCIS (Netherlands)

    Koelmans, A.A.; Nowack, B.; Wiesner, M.

    2009-01-01

    In this paper, we show that concentrations of manufactured carbon-based nanoparticles (MCNPs) in aquatic sediments will be negligible compared to levels of black carbon nanoparticles (BCNPs). This is concluded from model calculations accounting for MCNP sedimentation fluxes, removal rates due to

  6. Dynamac molecular structure of plant biomass-derived black carbon (Biochar)

    Science.gov (United States)

    Char black carbon (BC), the solid residue of incomplete combustion, is continuously being added to soils and sediments due to natural vegetation fires, anthropogenic pollution, and new strategies for carbon sequestration (“biochar”). Here we present a molecular-level assessment o...

  7. Robust Means for Estimating Black Carbon-Water Sorption Coefficients of Organic Contaminants in Sediments

    Science.gov (United States)

    2015-07-01

    include "black carbons" (BCs) such as soots and biomass chars, and that 4 these special components of the organic carbon content must be distinguished... disadvantages of the traditional batch method: difficult soot-water separation, long equilibrium time, high sorbents consumption, and uncertainty

  8. Sedimentary records of black carbon in the sea area of the Nansha Islands since the last glaciation

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Core 17962 taken from the sea area of the Nansha Islands recorded a sedimentary history of more than 30 000 years. The black carbon data from the core, which can inform us of the history of vegetation fires, show that during the last glaciation, especially during the last glacial maximum at about 18 kaBP, the fluctuation of the concentration and accumulation rate of the black carbon was relatively great, whereas it was small during the Holocene. The isotope composition of the black carbon indicates that the precursors of black carbon were mainly grasses from the last glaciation to the Holocene. The sub-alpine and alpine vegetation zones covered mainly with grass and bush on the lands around the southern South China Sea were probably the sources of black carbon. The altitudinal vegetation changes from the last glaciation to the Holocene gave rise to the changes of the sedimentary characteristics of black carbon.

  9. Black carbon from the Mississippi River: quantities, sources, and potential implications for the global carbon cycle.

    Science.gov (United States)

    Mitra, Siddhartha; Bianchi, Thomas S; McKee, Brent A; Sutula, Martha

    2002-06-01

    Black carbon (BC) may be a major component of riverine carbon exported to the ocean, but its flux from large rivers is unknown. Furthermore, the global distribution of BC between natural and anthropogenic sources remains uncertain. We have determined BC concentrations in suspended sediments of the Mississippi River, the 7th largest river in the world in terms of sediment and water discharge, during high flow and low flow in 1999. The 1999 annual flux of BC from the Mississippi River was 5 x 10(-4) petagrams (1 Pg = 10(15) g = 1 gigaton). We also applied a principal components analysis to particulate-phase high molecular weight polycyclic aromatic hydrocarbon isomer ratios in Mississippi River suspended sediments. In doing so, we determined that approximately 27% of the BC discharged from the Mississippi River in 1999 originated from fossil fuel combustion (coal and smelter-derived combustion), implicating fluvial BC as an important source of anthropogenic BC contamination into the ocean. Using our value for BC flux and the annual estimate for BC burial in ocean sediments, we calculate that, in 1999, the Mississippi River discharged approximately 5% of the BC buried annually in the ocean. These results have important implications, not only for the global carbon cycle but also for the fluvial discharge of particulate organic contaminants into the world's oceans.

  10. Attribution of aerosol light absorption to black carbon, brown carbon, and dust in China - interpretations of atmospheric measurements during EAST-AIRE

    Science.gov (United States)

    Yang, M.; Howell, S. G.; Zhuang, J.; Huebert, B. J.

    2009-03-01

    Black carbon, brown carbon, and mineral dust are three of the most important light absorbing aerosols. Their optical properties differ greatly and are distinctive functions of the wavelength of light. Most optical instruments that quantify light absorption, however, are unable to distinguish one type of absorbing aerosol from another. It is thus instructive to separate total absorption from these different light absorbers to gain a better understanding of the optical characteristics of each aerosol type. During the EAST-AIRE (East Asian Study of Tropospheric Aerosols: an International Regional Experiment) campaign near Beijing, we measured light scattering using a nephelometer, and light absorption using an aethalometer and a particulate soot absorption photometer. We also measured the total mass concentrations of carbonaceous (elemental and organic carbon) and inorganic particulates, as well as aerosol number and mass distributions. We were able to identify periods during the campaign that were dominated by dust, biomass burning, fresh (industrial) chimney plumes, other coal burning pollution, and relatively clean (background) air for Northern China. Each of these air masses possessed distinct intensive optical properties, including the single scatter albedo and Ångstrom exponents. Based on the wavelength-dependence and particle size distribution, we apportioned total light absorption to black carbon, brown carbon, and dust; their mass absorption efficiencies at 550 nm were estimated to be 9.5, 0.5 (a lower limit value), and 0.03 m2/g, respectively. While agreeing with the common consensus that black carbon is the most important light absorber in the mid-visible, we demonstrated that brown carbon and dust could also cause significant absorption, especially at shorter wavelengths.

  11. Attribution of aerosol light absorption to black carbon, brown carbon, and dust in China – interpretations of atmospheric measurements during EAST-AIRE

    Directory of Open Access Journals (Sweden)

    M. Yang

    2009-03-01

    Full Text Available Black carbon, brown carbon, and mineral dust are three of the most important light absorbing aerosols. Their optical properties differ greatly and are distinctive functions of the wavelength of light. Most optical instruments that quantify light absorption, however, are unable to distinguish one type of absorbing aerosol from another. It is thus instructive to separate total absorption from these different light absorbers to gain a better understanding of the optical characteristics of each aerosol type. During the EAST-AIRE (East Asian Study of Tropospheric Aerosols: an International Regional Experiment campaign near Beijing, we measured light scattering using a nephelometer, and light absorption using an aethalometer and a particulate soot absorption photometer. We also measured the total mass concentrations of carbonaceous (elemental and organic carbon and inorganic particulates, as well as aerosol number and mass distributions. We were able to identify periods during the campaign that were dominated by dust, biomass burning, fresh (industrial chimney plumes, other coal burning pollution, and relatively clean (background air for Northern China. Each of these air masses possessed distinct intensive optical properties, including the single scatter albedo and Ångstrom exponents. Based on the wavelength-dependence and particle size distribution, we apportioned total light absorption to black carbon, brown carbon, and dust; their mass absorption efficiencies at 550 nm were estimated to be 9.5, 0.5 (a lower limit value, and 0.03 m2/g, respectively. While agreeing with the common consensus that black carbon is the most important light absorber in the mid-visible, we demonstrated that brown carbon and dust could also cause significant absorption, especially at shorter wavelengths.

  12. Short-Range-Order Mineral Physical Protection On Black Carbon Stabilization

    Science.gov (United States)

    Liang, B.; Weng, Y. T.; Wang, C. C.; Song, Y. F.; Lehmann, J.; Wang, C. H.

    2015-12-01

    Soil organic matter is one of the largest reservoirs in global carbon cycle, and black carbon (BC) represents a chemical resistant component. Black C plays an important role in global climate change. Generally considered recalcitrant due to high aromaticity, the reactive surface and functional groups of BC are crucial for carbon sequestration in soils. Mineral sorption and physical protection is an important mechanism for BC long term stabilization and sequestration in environments. Previous studies on mineral protection of BC were limited to analysis techniques in two-dimensions, for example, by SEM, TEM, and NanoSIMS. Little is known about the scope of organo-mineral association, the in-situ distribution and forms of minerals, and the ultimate interplay of BC and minerals. The aim of this study is to investigate the three-dimensional interaction of organic C and minerals in submicron scale using synchrotron-based Transmission X-ray Microcopy (TXM) and Fourier-Transform Infrared Spectroscopy (FTIR). Abundant poorly-crystallined nano-minerals particles were observed. These short-range-order (SRO) minerals also aggregate into clusters and sheets, and form envelops-like structures on the surface of BC. On top of large surface contact area, the intimate interplay between BC and minerals reinforces the stability of both organic C and minerals, resulting from chemical bonding through cation bridging and ligand exchange. The mineral protection enhances BC stabilization and sequestration and lowers its bioavailability in environment. The results suggest that mineral physical protection for BC sequestration may be more important than previous understanding.

  13. Thermal Oxidation of Tail Gases from the Production of Oil-furnace Carbon Black

    Directory of Open Access Journals (Sweden)

    Bosak, Z.

    2009-01-01

    Full Text Available This paper describes the production technology of oil-furnace carbon black, as well as the selected solution for preventing the emissions of this process from contaminating the environment.The products of industrial oil-furnace carbon black production are different grades of carbon black and process tail gases. The qualitative composition of these tail gases during the production of oil-furnace carbon black are: carbon(IV oxide, carbon(II oxide, hydrogen, methane, hydrogen sulfide, nitrogen, oxygen, and water vapor.The quantitative composition and lower caloric value of process tail gases change depending on the type of feedstock used in the production, as well as the type of process. The lower caloric value of process tail gases is relatively small with values ranging between 1500 and 2300 kJ m–3.In the conventional production of oil-furnace carbon black, process tail gases purified from carbon black dust are freely released into the atmosphere untreated. In this manner, the process tail gases pollute the air in the town of Kutina, because their quantitative values are much higher than the prescribed emissions limits for hydrogen sulfide and carbon(II oxide. A logical solution for the prevention of such air pollution is combustion of the process tail gases, i. e. their thermal oxidation. For this purpose, a specially designed flare system has been developed. Consuming minimum amounts of natural gas needed for oxidation, the flare system is designed to combust low caloric process tail gases with 99 % efficiency. Thus, the toxic and flammable components of the tail gases (hydrogen sulfide, hydrogen, carbon(II oxide, methane and other trace hydrocarbons would be transformed into environmentally acceptable components (sulfur(IV oxide, water, carbon(IV oxide and nitrogen(IV oxide, which are in compliance with the emissions limit values prescribed by law.Proper operation of this flare system in the production of oil-furnace carbon black would solve

  14. Carbon Nanotube Purification and Functionalization

    Science.gov (United States)

    Lebron, Marisabel; Mintz, Eric; Smalley, Richard E.; Meador, Michael A.

    2003-01-01

    Carbon nanotubes have the potential to significantly enhance the mechanical, thermal, and electrical properties of polymers. However, dispersion of carbon nanotubes in a polymer matrix is hindered by the electrostatic forces that cause them to agglomerate. Chemical modification of the nanotubes is necessary to minimize these electrostatic forces and promote adhesion between the nanotubes and the polymer matrix. In a collaborative research program between Clark Atlanta University, Rice University, and NASA Glenn Research Center several approaches are being explored to chemically modify carbon nanotubes. The results of this research will be presented.

  15. Aerosol light absorption, black carbon, and elemental carbon at the Fresno Supersite, California

    Science.gov (United States)

    Chow, Judith C.; Watson, John G.; Doraiswamy, Prakash; Chen, Lung-Wen Antony; Sodeman, David A.; Lowenthal, Douglas H.; Park, Kihong; Arnott, W. Patrick; Motallebi, Nehzat

    2009-08-01

    Particle light absorption ( bap), black carbon (BC), and elemental carbon (EC) measurements at the Fresno Supersite during the summer of 2005 were compared to examine the equivalency of current techniques, evaluate filter-based bap correction methods, and determine the EC mass absorption efficiency (σ ap) and the spectral dependence of bap. The photoacoustic analyzer (PA) was used as a benchmark for in-situ bap. Most bap measurement techniques were well correlated ( r ≥ 0.95). Unadjusted Aethalometer (AE) and Particle Soot Absorption Photometer (PSAP) bap were up to seven times higher than PA bap at similar wavelengths because of absorption enhancement by backscattering and multiple scattering. Applying published algorithms to correct for these effects reduced the differences to 24 and 17% for the AE and PSAP, respectively, at 532 nm. The Multi-Angle Absorption Photometer (MAAP), which accounts for backscattering effects, overestimated bap relative to the PA by 51%. BC concentrations determined by the AE, MAAP, and Sunset Laboratory semi-continuous carbon analyzer were also highly correlated ( r ≥ 0.93) but differed by up to 57%. EC measured with the IMPROVE/STN thermal/optical protocols, and the French two-step thermal protocol agreed to within 29%. Absorption efficiencies determined from PA bap and EC measured with different analytical protocols averaged 7.9 ± 1.5, 5.4 ± 1.1, and 2.8 ± 0.6 m 2/g at 532, 670, and 1047 nm, respectively. The Angström exponent (α) determined from adjusted AE and PA bap ranged from 1.19 to 1.46. The largest values of α occurred during the afternoon hours when the organic fraction of total carbon was highest. Significant biases associated with filter-based measurements of bap, BC, and EC are method-specific. Correcting for these biases must take into account differences in aerosol concentration, composition, and sources.

  16. Personal black carbon exposure influences ambulatory blood pressure: air pollution and cardiometabolic disease (AIRCMD-China) study.

    Science.gov (United States)

    Zhao, Xiaoyi; Sun, Zhichao; Ruan, Yanping; Yan, Jianhua; Mukherjee, Bhramar; Yang, Fumo; Duan, Fengkui; Sun, Lixian; Liang, Ruijuan; Lian, Hui; Zhang, Shuyang; Fang, Quan; Gu, Dongfeng; Brook, Jeffrey R; Sun, Qinghua; Brook, Robert D; Rajagopalan, Sanjay; Fan, Zhongjie

    2014-04-01

    Few prospective studies have assessed the blood pressure effect of extremely high air pollution encountered in Asia's megacities. The objective of this study was to evaluate the association between combustion-related air pollution with ambulatory blood pressure and autonomic function. During February to July 2012, personal black carbon was determined for 5 consecutive days using microaethalometers in patients with metabolic syndrome in Beijing, China. Simultaneous ambient fine particulate matter concentration was obtained from the Beijing Municipal Environmental Monitoring Center and the US Embassy. Twenty-four-hour ambulatory blood pressure and heart rate variability were measured from day 4. Arterial stiffness and endothelial function were obtained at the end of day 5. For statistical analysis, we used generalized additive mixed models for repeated outcomes and generalized linear models for single/summary outcomes. Mean (SD) of personal black carbon and fine particulate matter during 24 hours was 4.66 (2.89) and 64.2 (36.9) μg/m(3). Exposure to high levels of black carbon in the preceding hours was associated significantly with adverse cardiovascular responses. A unit increase in personal black carbon during the previous 10 hours was associated with an increase in systolic blood pressure of 0.53 mm Hg and diastolic blood pressure of 0.37 mm Hg (95% confidence interval, 0.17-0.89 and 0.10-0.65 mm Hg, respectively), a percentage change in low frequency to high frequency ratio of 5.11 and mean interbeat interval of -0.06 (95% confidence interval, 0.62-9.60 and -0.11 to -0.01, respectively). These findings highlight the public health effect of air pollution and the importance of reducing air pollution.

  17. Evaluation of Black Carbon Estimations in Global Aerosol Models

    Energy Technology Data Exchange (ETDEWEB)

    Koch, D.; Schulz, M.; Kinne, Stefan; McNaughton, C. S.; Spackman, J. R.; Balkanski, Y.; Bauer, S.; Berntsen, T.; Bond, Tami C.; Boucher, Olivier; Chin, M.; Clarke, A. D.; De Luca, N.; Dentener, F.; Diehl, T.; Dubovik, O.; Easter, Richard C.; Fahey, D. W.; Feichter, J.; Fillmore, D.; Freitag, S.; Ghan, Steven J.; Ginoux, P.; Gong, S.; Horowitz, L.; Iversen, T.; Kirkevag, A.; Klimont, Z.; Kondo, Yutaka; Krol, M.; Liu, Xiaohong; Miller, R.; Montanaro, V.; Moteki, N.; Myhre, G.; Penner, J.; Perlwitz, Ja; Pitari, G.; Reddy, S.; Sahu, L.; Sakamoto, H.; Schuster, G.; Schwarz, J. P.; Seland, O.; Stier, P.; Takegawa, Nobuyuki; Takemura, T.; Textor, C.; van Aardenne, John; Zhao, Y.

    2009-11-27

    We evaluate black carbon (BC) model predictions from the AeroCom model intercomparison project by considering the diversity among year 2000 model simulations and comparing model predictions with available measurements. These model-measurement intercomparisons include BC surface and aircraft concentrations, aerosol absorption optical depth (AAOD) from AERONET and OMI retrievals and BC column estimations based on AERONET. In regions other than Asia, most models are biased high compared to surface concentration measurements. However compared with (column) AAOD or BC burden retreivals, the models are generally biased low. The average ratio of model to retrieved AAOD is less than 0.7 in South American and 0.6 in African biomass burning regions; both of these regions lack surface concentration measurements. In Asia the average model to observed ratio is 0.6 for AAOD and 0.5 for BC surface concentrations. Compared with aircraft measurements over the Americas at latitudes between 0 and 50N, the average model is a factor of 10 larger than observed, and most models exceed the measured BC standard deviation in the mid to upper troposphere. At higher latitudes the average model to aircraft BC is 0.6 and underestimate the observed BC loading in the lower and middle troposphere associated with springtime Arctic haze. Low model bias for AAOD but overestimation of surface and upper atmospheric BC concentrations at lower latitudes suggests that most models are underestimating BC absorption and should improve estimates for refractive index, particle size, and optical effects of BC coating. Retrieval uncertainties and/or differences with model diagnostic treatment may also contribute to the model-measurement disparity. Largest AeroCom model diversity occurred in northern Eurasia and the remote Arctic, regions influenced by anthropogenic sources. Changing emissions, aging, removal, or optical properties within a single model generated a smaller change in model predictions than the

  18. Factors Controlling Black Carbon Deposition in Snow in the Arctic

    Science.gov (United States)

    Qi, L.; Li, Q.; He, C.; Li, Y.

    2015-12-01

    This study evaluates the sensitivity of black carbon (BC) concentration in snow in the Arctic to BC emissions, dry deposition and wet scavenging efficiency using a 3D global chemical transport model GEOS-Chem driven by meteorological field GEOS-5. With all improvements, simulated median BC concentration in snow agrees with observation (19.2 ng g-1) within 10%, down from -40% in the default GEOS-Chem. When the previously missed gas flaring emissions (mainly located in Russia) are included, the total BC emission in the Arctic increases by 70%. The simulated BC in snow increases by 1-7 ng g-1, with the largest improvement in Russia. The discrepancy of median BC in snow in the whole Arctic reduces from -40% to -20%. In addition, recent measurements of BC dry deposition velocity suggest that the constant deposition velocity of 0.03 cm s-1 over snow and ice used in the GEOS-Chem is too low. So we apply resistance-in-series method to calculate the dry deposition velocity over snow and ice and the resulted dry deposition velocity ranges from 0.03 to 0.24 cm s-1. However, the simulated total BC deposition flux in the Arctic and BC in snow does not change, because the increased dry deposition flux has been compensated by decreased wet deposition flux. However, the fraction of dry deposition to total deposition increases from 16% to 25%. This may affect the mixing of BC and snow particles and further affect the radative forcing of BC deposited in snow. Finally, we reduced the scavenging efficiency of BC in mixed-phase clouds to account for the effect of Wegener-Bergeron-Findeisen (WBF) process based on recent observations. The simulated BC concentration in snow increases by 10-100%, with the largest increase in Greenland (100%), Tromsø (50%), Alaska (40%), and Canadian Arctic (30%). Annual BC loading in the Arctic increases from 0.25 to 0.43 mg m-2 and the lifetime of BC increases from 9.2 to 16.3 days. This indicates that BC simulation in the Arctic is really sensitive to

  19. Evaluation of black carbon estimations in global aerosol models

    Directory of Open Access Journals (Sweden)

    Y. Zhao

    2009-11-01

    Full Text Available We evaluate black carbon (BC model predictions from the AeroCom model intercomparison project by considering the diversity among year 2000 model simulations and comparing model predictions with available measurements. These model-measurement intercomparisons include BC surface and aircraft concentrations, aerosol absorption optical depth (AAOD retrievals from AERONET and Ozone Monitoring Instrument (OMI and BC column estimations based on AERONET. In regions other than Asia, most models are biased high compared to surface concentration measurements. However compared with (column AAOD or BC burden retreivals, the models are generally biased low. The average ratio of model to retrieved AAOD is less than 0.7 in South American and 0.6 in African biomass burning regions; both of these regions lack surface concentration measurements. In Asia the average model to observed ratio is 0.7 for AAOD and 0.5 for BC surface concentrations. Compared with aircraft measurements over the Americas at latitudes between 0 and 50N, the average model is a factor of 8 larger than observed, and most models exceed the measured BC standard deviation in the mid to upper troposphere. At higher latitudes the average model to aircraft BC ratio is 0.4 and models underestimate the observed BC loading in the lower and middle troposphere associated with springtime Arctic haze. Low model bias for AAOD but overestimation of surface and upper atmospheric BC concentrations at lower latitudes suggests that most models are underestimating BC absorption and should improve estimates for refractive index, particle size, and optical effects of BC coating. Retrieval uncertainties and/or differences with model diagnostic treatment may also contribute to the model-measurement disparity. Largest AeroCom model diversity occurred in northern Eurasia and the remote Arctic, regions influenced by anthropogenic sources. Changing emissions, aging, removal, or optical properties within a single model

  20. Evaluation of black carbon estimations in global aerosol models

    Directory of Open Access Journals (Sweden)

    D. Koch

    2009-07-01

    Full Text Available We evaluate black carbon (BC model predictions from the AeroCom model intercomparison project by considering the diversity among year 2000 model simulations and comparing model predictions with available measurements. These model-measurement intercomparisons include BC surface and aircraft concentrations, aerosol absorption optical depth (AAOD from AERONET and Ozone Monitoring Instrument (OMI retrievals and BC column estimations based on AERONET. In regions other than Asia, most models are biased high compared to surface concentration measurements. However compared with (column AAOD or BC burden retreivals, the models are generally biased low. The average ratio of model to retrieved AAOD is less than 0.7 in South American and 0.6 in African biomass burning regions; both of these regions lack surface concentration measurements. In Asia the average model to observed ratio is 0.6 for AAOD and 0.5 for BC surface concentrations. Compared with aircraft measurements over the Americas at latitudes between 0 and 50 N, the average model is a factor of 10 larger than observed, and most models exceed the measured BC standard deviation in the mid to upper troposphere. At higher latitudes the average model to aircraft BC is 0.6 and underestimates the observed BC loading in the lower and middle troposphere associated with springtime Arctic haze. Low model bias for AAOD but overestimation of surface and upper atmospheric BC concentrations at lower latitudes suggests that most models are underestimating BC absorption and should improve estimates for refractive index, particle size, and optical effects of BC coating. Retrieval uncertainties and/or differences with model diagnostic treatment may also contribute to the model-measurement disparity. Largest AeroCom model diversity occurred in northern Eurasia and the remote Arctic, regions influenced by anthropogenic sources. Changing emissions, aging, removal, or optical properties within a single model generated a

  1. Estimation of Black Carbon Emissions from Dry Dipterocarp Forest Fires in Thailand

    Directory of Open Access Journals (Sweden)

    Ubonwan Chaiyo

    2014-12-01

    Full Text Available This study focused on the estimation of black carbon emissions from dry dipterocarp forest fires in Thailand. Field experiments were set up at the natural forest, Mae Nam Phachi wildlife sanctuary, Ratchaburi Province, Thailand. The dead leaves were the main component consumed of the surface biomass with coverage higher than 90% in volume and mass. The dead leaves load was 342 ± 190 g∙m−2 and followed by a little mass load of twig, 100 g∙m−2. The chemical analysis of the dead leaves showed that the carbon content in the experimental biomass fuel was 45.81 ± 0.04%. From the field experiments, it was found that 88.38 ± 2.02% of the carbon input was converted to carbon released to the atmosphere, while less than 10% were left in the form of residues, and returned to soil. The quantity of dead leaves consumed to produce each gram of carbon released was 2.40 ± 0.02 gdry biomass burned. From the study, the emissions factor of carbon dioxide, carbon monoxide, particulate matter (PM2.5 and black carbon amounted 1329, 90, 26.19 and 2.83 g∙kg−1dry biomass burned, respectively. In Thailand, the amount of black carbon emissions from dry dipterocarp forest fires amounted 17.43 tonnes∙y−1.

  2. Self-sensing piezoresistive cement composite loaded with carbon black particles

    KAUST Repository

    Monteiro, André O.

    2017-04-27

    Strain sensors can be embedded in civil engineering infrastructures to perform real-time service life monitoring. Here, the sensing capability of piezoresistive cement-based composites loaded with carbon black (CB) particles is investigated. Several composite mixtures, with a CB filler loading up to 10% of binder mass, were mechanically tested under cyclic uniaxial compression, registering variations in electrical resistance as a function of deformation. The results show a reversible piezoresistive behaviour and a quasi-linear relation between the fractional change in resistivity and the compressive strain, in particular for those compositions with higher amount of CB. Gage factors of 30 and 24 were found for compositions containing 7 and 10% of binder mass, respectively. These findings suggest that the CB-cement composites may be a promising active material to monitor compressive strain in civil infrastructures such as concrete bridges and roadways.

  3. Estimate the influence of snow grain size and black carbon on albedo

    Institute of Scientific and Technical Information of China (English)

    ZhongMing Guo; NingLian Wang; XiaoBo Wu; HongBo Wu; YuWei Wu

    2015-01-01

    Estimation of the influence of snow grain size and black carbon on albedo is essential in obtaining the accurate albedo. In this paper, field measurement data, including snow grain size, snow depth and density was obtained. Black carbon samples were collected from the snow surface. A simultaneous observation using Analytical Spectral Devices was employed in the Qiyi Glacier located in the Qilian Mountain. Analytical Spectral Devices spectrum data were used to analyze spectral re-flectance of snow for different grain size and black carbon content. The measurements were compared with the results obtained from the Snow, Ice, and Aerosol Radiation model, and the simulation was found to correlate well with the ob-served data. However, the simulated albedo was near to 0.98 times of the measured albedo, so the other factors were as-sumed to be constant using the corrected Snow, Ice, and Aerosol Radiation model to estimate the influence of measured snow grain size and black carbon on albedo. Field measurements were controlled to fit the relationship between the snow grain size and black carbon in order to estimate the influence of these factors on the snow albedo.

  4. Migration of nanoparticles from plastic packaging materials containing carbon black into foodstuffs.

    Science.gov (United States)

    Bott, Johannes; Störmer, Angela; Franz, Roland

    2014-01-01

    Carbon black was investigated to assess and quantify the possibility that nanoparticles might migrate out of plastic materials used in the food packaging industry. Two types of carbon black were incorporated in low-density polyethylene (LDPE) and polystyrene (PS) at 2.5% and 5.0% loading (w/w), and then subjected to migration studies. The samples were exposed to different food simulants according to European Union Plastics Regulation 10/2011, simulating long-term storage with aqueous and fatty foodstuffs. Asymmetric flow field-flow fractionation (AF4) coupled to a multi-angle laser light-scattering (MALLS) detector was used to separate, characterise and quantify the potential release of nanoparticles. The AF4 method was successful in differentiating carbon black from other matrix components, such as extracted polymer chains, in the migration solution. At a detection limit of 12 µg kg⁻¹, carbon black did not migrate from the packaging material into food simulants. The experimental findings are in agreement with theoretical considerations based on migration modelling. From both the experimental findings and theoretical considerations, it can be concluded that carbon black does not migrate into food once it is incorporated into a plastics food contact material.

  5. Effect of molecular weight on the electrophoretic deposition of carbon black nanoparticles in moderately viscous systems.

    Science.gov (United States)

    Modi, Satyam; Panwar, Artee; Mead, Joey L; Barry, Carol M F

    2013-08-06

    Electrophoretic deposition from viscous media has the potential to produce in-mold assembly of nanoparticles onto three-dimensional parts in high-rate, polymer melt-based processes like injection molding. The effects of the media's molecular weight on deposition behavior were investigated using a model system of carbon black and polystyrene in tetrahydrofuran. Increases in molecular weight reduced the electrophoretic deposition of the carbon black particles due to increases in suspension viscosity and preferential adsorption of the longer polystyrene chains on the carbon black particles. At low deposition times (≤5 s), only carbon black deposited onto the electrodes, but the deposition decreased with increasing molecular weight and the resultant increases in suspension viscosity. For longer deposition times, polystyrene codeposited with the carbon black, with the amount of polystyrene increasing with molecular weight and decreasing with greater charge on the polystyrene molecules. This deposition behavior suggests that use of lower molecular polymers and control of electrical properties will permit electrophoretic deposition of nanoparticles from polymer melts for high-rate, one-step fabrication of nano-optical devices, biochemical sensors, and nanoelectronics.

  6. Quantitative Analysis of Major Factors Affecting Black Carbon Transport and Concentrations in the Unique Atmospheric Structures of Urban Environment

    Science.gov (United States)

    Liang, Marissa Shuang

    Black carbon (BC) from vehicular emission in transportation is a principal component of particulate matters ≤ 2.5 mum (PM2.5). PM2.5 and other diesel emission pollutants (e.g., NOx) are regulated by the Clean Air Act (CAA) according to the National Ambient Air Quality standards (NAAQS). This doctoral dissertation details a study on transport behaviors of black carbon and PM2.5 from transportation routes, their relations with the atmospheric structure of an urban formation, and their relations with the use of biodiesel fuels. The results have implications to near-road risk assessment and to the development of sustainable transportation solutions in urban centers. The first part of study quantified near-roadside black carbon transport as a function of particulate matter (PM) size and composition, as well as microclimatic variables (temperature and wind fields) at the interstate highway I-75 in northern Cincinnati, Ohio. Among variables examined, wind speed and direction significantly affect the roadside transport of black carbon and hence its effective emission factor. Observed non-Gaussian dispersion occurred during low wind and for wind directions at acute angles or upwind to the receptors, mostly occurring in the morning hours. Meandering of air pollutant mass under thermal inversion is likely the driving force. In contrary, Gaussian distribution predominated in daytime of strong downwinds. The roles of urban atmospheric structure, wind fields, and the urban heat island (UHI) effects were further examined on pollutant dispersion and transport. Spatiotemporal variations of traffic flow, atmospheric structure, ambient temperature and PM2.5 concentration data from 14 EPA-certified NAAQS monitoring stations, were analyzed in relation to land-use in the Cincinnati metropolitan area. The results show a decade-long UHI effects with higher interior temperature than that in exurban, and a prominent nocturnal thermal inversion frequent in urban boundary layer. The

  7. Dynamic molecular structure of plant biomass-derived black carbon (biochar)

    Energy Technology Data Exchange (ETDEWEB)

    Keiluweit, M.; Nico, P.S.; Johnson, M.G.; Kleber, M.

    2009-11-15

    Char black carbon (BC), the solid residue of incomplete combustion, is continuously being added to soils and sediments due to natural vegetation fires, anthropogenic pollution, and new strategies for carbon sequestration ('biochar'). Here we present a molecular-level assessment of the physical organization and chemical complexity of biomass-derived chars and, specifically, that of aromatic carbon in char structures. BET-N{sub 2} surface area, X-ray diffraction (XRD), synchrotron-based Near-edge X-ray Absorption Fine Structure (NEXAFS), and Fourier transform infrared (FT-IR) spectroscopy are used to show how two plant materials (wood and grass) undergo analogous, but quantitatively different physical-chemical transitions as charring temperature increases from 100 to 700 C. These changes suggest the existence of four distinct categories of char consisting of a unique mixture of chemical phases and physical states: (i) in transition chars the crystalline character of the precursor materials is preserved, (ii) in amorphous chars the heat-altered molecules and incipient aromatic polycondensates are randomly mixed, (iii) composite chars consist of poorly ordered graphene stacks embedded in amorphous phases, and (iv) turbostratic chars are dominated by disordered graphitic crystallites. The molecular variations among the different char categories translate into differences in their ability to persist in the environment and function as environmental sorbents.

  8. Effect of carbon-black treatment by radiation emulsion polymerization on temperature dependence of resistivity of carbon-black-filled polymer blends

    Energy Technology Data Exchange (ETDEWEB)

    Jia Shaojin [Key Lab of Insulation and Thermal of Aging of Shanghai, Department of Polymer Engineering and Science, Shanghai Jiao Tong University, Dongchuan Road 800, Shanghai 200240 (China) and Department of Chemical Engineering, Shanghai University, Chengzhong Road 20, Shanghai 201800 (China)]. E-mail: jiashaojin2@yahoo.com.cn; Jiang Pingkai [Key Lab of Insulation and Thermal of Aging of Shanghai, Department of Polymer Engineering and Science, Shanghai Jiao Tong University, Dongchuan Road 800, Shanghai 200240 (China); Zhang Zhicheng [Department of Polymer Science and Engineering, University of Science and Technology of China, Hefei, Anhui 230026 (China); Wang Zhongguang [Key Lab of Insulation and Thermal of Aging of Shanghai, Department of Polymer Engineering and Science, Shanghai Jiao Tong University, Dongchuan Road 800, Shanghai 200240 (China)

    2006-04-15

    High dispersibility and stability of carbon black particles in low-density-polyethylene (LDPE) matrix were obtained by radiation emulsion polymerization on carbon particles surface, and electrical resistivities of its simple were examined. First carbon particles treatment on radiation emulsion polymerization on surface were synthesized by the reaction with a polymer-emulsion systems containing reactive group in the molecular unit, carbon particles and emulsifier. Then, the carbon particles treatment on radiation emulsion polymerization on surface was dispersed into LDPE, and its composites were prepared for electrical measurements. The effect of radiation crosslinking of the composite on the Positive temperature coefficient (PTC) and negative temperature coefficient (NTC) phenomenon was investigated. The experimental results showed that PTC and NTC effects of the composites were obviously influenced by the irradiation dose. Various microstructure-exploring means were used to study the conductive composite, such as scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electron microscopy (TEM)

  9. Effect of carbon-black treatment by radiation emulsion polymerization on temperature dependence of resistivity of carbon-black-filled polymer blends

    Science.gov (United States)

    Shaojin, Jia; Pingkai, Jiang; Zhicheng, Zhang; Zhongguang, Wang

    2006-04-01

    High dispersibility and stability of carbon black particles in low-density-polyethylene (LDPE) matrix were obtained by radiation emulsion polymerization on carbon particles surface, and electrical resistivities of its simple were examined. First carbon particles treatment on radiation emulsion polymerization on surface were synthesized by the reaction with a polymer-emulsion systems containing reactive group in the molecular unit, carbon particles and emulsifier. Then, the carbon particles treatment on radiation emulsion polymerization on surface was dispersed into LDPE, and its composites were prepared for electrical measurements. The effect of radiation crosslinking of the composite on the Positive temperature coefficient (PTC) and negative temperature coefficient (NTC) phenomenon was investigated. The experimental results showed that PTC and NTC effects of the composites were obviously influenced by the irradiation dose. Various microstructure-exploring means were used to study the conductive composite, such as scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electron microscopy (TEM).

  10. Functionalized carbon nanomaterials derived from carbohydrates.

    Science.gov (United States)

    Jagadeesan, Dinesh; Eswaramoorthy, Muthusamy

    2010-02-01

    A tremendous growth in the field of carbon nanomaterials has led to the emergence of carbon nanotubes, fullerenes, mesoporous carbon and more recently graphene. Some of these materials have found applications in electronics, sensors, catalysis, drug delivery, composites, and so forth. The high temperatures and hydrocarbon precursors involved in their synthesis usually yield highly inert graphitic surfaces. As some of the applications require functionalization of their inert graphitic surface with groups like -COOH, -OH, and -NH(2), treatment of these materials in oxidizing agents and concentrated acids become inevitable. More recent works have involved using precursors like carbohydrates to produce carbon nanostructures rich in functional groups in a single-step under hydrothermal conditions. These carbon nanostructures have already found many applications in composites, drug delivery, materials synthesis, and Li ion batteries. The review aims to highlight some of the recent developments in the application of carbohydrate derived carbon nanostructures and also provide an outlook of their future prospects.

  11. Adsorption removal of acid black 1 from aqueous solution using ordered mesoporous carbon

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Xiaoming, E-mail: pengxiaoming70@126.com [School of Civil Engineering, Southeast University, Nanjing 210096 (China); Hu, Xijun [Department of Chemical and Biomolecular Engineering, The Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong,China (China); Fu, Dafang, E-mail: fdf@seu.edu.cn [School of Civil Engineering, Southeast University, Nanjing 210096 (China); Lam, Frank L.Y. [Department of Chemical and Biomolecular Engineering, The Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong,China (China)

    2014-03-01

    Highlights: • Ordered mesoporous carbon was prepared using template. • Ordered mesoporous carbon was introduced of N-containing group by Chemical vapor deposition method. • Modified CMK-3 have better adsorption capacity and efficiency than virgin CMK-3 to removal AB1 dye. - Abstract: A novel ordered mesoporous carbon CMK-3 and synthetic CMK-3 containing nitrogen functional groups by ammonia-treated were applied for acid black 1(AB1) dye adsorption. The ammonia-treated(chemical vapor deposition method) before and after CMK-3 were characterized by using a Micrometitics ASAP 2020 surface area analyzer (ASAP 2020), Fourier transform infrared spectrophotometer (FT–IR), X-ray Photoelectron Spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscope (SEM) and equilibrium studies. This result indicates that the prepared CMK-3 and modified CMK-3 were almost uniform, as rope-like domains and their uniform mesopore with diameter centered at 3.2 nm and 3.7 nm. The FIIR analysis depicted that the presence of a variety of new basic functional groups on the modified CMK-3 surface. Several effect variables of pH, dye concentration and temperature were studied. The pseudo second-order model showed the fitter well to agree with the kinetic data. The experimental data were analyzed by the Langmuir and Freundlich models, with the latter found to closely the isotherm model. The adsorption kinetics was found to follow the pseudo-second-order kinetic model. The results show that CMK-3 using ammonia gas modified by thermal treatment system is an effective method to improvement capacity as it shows the highest adsorption capacity of AB1, as compared to the unmodified CMK-3 and the bamboo-based carbon, respectively.

  12. Aerosol organic carbon to black carbon ratios: Analysis ofpublished data and implications for climate forcing

    Energy Technology Data Exchange (ETDEWEB)

    Novakov, T.; Menon, S.; Kirchstetter, T.W.; Koch, D.; Hansen, J.E.

    2005-07-11

    Measurements of organic carbon (OC) and black carbon (BC)concentrations over a variety of locations worldwide, have been analyzed to infer the spatial distributions of the ratios of OC to BC. Since these ratios determine the relative amounts of scattering and absorption, they are often used to estimate the radiative forcing due to aerosols. An artifact in the protocol for filter measurements of OC has led to widespread overestimates of the ratio of OC to BC in atmospheric aerosols. We developed a criterion to correct for this artifact and analyze corrected OC to BC ratios. The OC to BC ratios, ranging from 1.3to 2.4, appear relatively constant and are generally unaffected by seasonality, sources or technology changes, at the locations considered here. The ratios compare well with emission inventories over Europe and China but are a factor of two lower in other regions. The reduced estimate for OC/BC in aerosols strengthens the argument that reduction of soot emissions maybe a useful approach to slow global warming.

  13. Measuring morphology and density of internally mixed black carbon with SP2 and VTDMA: new insight to absorption enhancement of black carbon in the atmosphere

    Directory of Open Access Journals (Sweden)

    Y. X. Zhang

    2015-11-01

    Full Text Available The morphology and density of black carbon (BC cores in internally mixed BC (In-BC particles affects their mixing state and absorption enhancement. In this work, we developed a new method to measure the morphology and effective density of BC cores of ambient In-BC particles using a single particle soot photometer (SP2 and a volatility tandem differential mobility analyzer (VTDMA, during the CAREBeijing-2013 campaign from 8 to 27 July 2013 at Xianghe Observatory. The new measurement system can select size-resolved ambient In-BC particles and measure the mobility size and mass of In-BC cores. The morphology and effective density of ambient In-BC cores are then calculated. For In-BC cores in the atmosphere, changes in the dynamic shape factor (χ and effective density (ρeff can be characterized as a function of aging process (Dp ⁄ Dc measured by SP2 and VTDMA. During an intensive field study, the ambient In-BC cores had an average χ of ∼ 1.2 and an average density of ∼ 1.2 g cm−3, indicating that ambient In-BC cores have a near-spherical shape with an internal void of ∼ 30 %. With the measured morphology and density, the average shell ⁄ core ratio and absorption enhancement (Eab from ambient black carbon were estimated to be 2.1–2.7 and 1.6–1.9 for different sizes of In-BC particles at 200–350 nm. When assuming the In-BC cores have a void-free BC sphere with a density of 1.8 g cm−3, the shell ⁄ core ratio and Eab could be overestimated by ∼ 13 and ∼ 17 % respectively. The new approach developed in this work will help improve calculations of mixing state and optical properties of ambient In-BC particles by quantification of changes in morphology and density of ambient In-BC cores during aging process.

  14. Thickness effect on electric resistivity on polystyrene and carbon black- based composites

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Lopez, S; Vigueras-Santiago, E [Laboratorio de Investigacion y Desarrollo de Materiales Avanzados (LIDMA) Facultad de Quimica, Paseo Colon Esquina con Paseo Tollocan, s/n, CP 50000, Toluca (Mexico); Mayorga-Rojas, M; Reyes-Contreras, D, E-mail: eviguerass@uaemex.m [Facultad de Ciencias, Universidad Autonoma del Estado de Mexico. Av. Instituto Literario 100 Ote. C. P. 50000, Toluca (Mexico)

    2009-05-01

    Changes on electrical resistivity were experimentally studied for polystyrene and carbon black-based composites respect to the temperature. 22% w/w carbon black composite films at 30{mu}m, 2mm y 1cm thick were submitted to thermal heating-cooling cycles from room temperature to 100 deg. C, slightly up to T{sub g} of the composite. For each cycle changes on electrical resistivity constituent a hysteresis loop that depends on the sample thickness. The changes during the heating stage could be explained as a consequence of the thermal expansion and mobility of the polymer chains at T{sub g}, producing a disconnecting of the electrical contacts among carbon black particles and an important increasing (200%) of the electrical resistivity. For each cycle, the hysteresis loop was observed in thicker samples, whereas for 30 mu m thickness sample the hysteresis loop was lost after four cycles.

  15. Influence of γ-ray Irradiation on the PTC Effect of EPDM/Carbon Black Composite

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@ Introduction The positive temperature coefficient(PTC) effect is characterized by an increase of resistivity with an elevated temperature.The PTC effect of carbon black(CB) filled polymers is useful for self-regulation heaters,over-current protectors,sensors,etc.Much work has been done on the PTC effect of the carbon black filled crystalline polymer composite[1-4],whereas carbon black filled amorphous polymers have not drawn researchers much attention because the PTC effect in these composites is small or cannot be detected[5-7].In this work,the influence of γ-ray irradiation on the PTC effect of CB filled amorphous ethylene-propylene-diene terpolymer(EPDM) composites was studied.

  16. A method for monitoring mass concentration of black carbon particulate matter using photothermal interferometry.

    Science.gov (United States)

    Li, Baosheng; Wang, Yicheng; Li, Zhengqiang

    2016-03-01

    A method for measurements of mass concentration of black carbon particulate matter (PM) is proposed based on photothermal interferometry (PTI). A folded Jamin photothermal interferometer was used with a laser irradiation of particles deposited on a filter paper. The black carbon PM deposited on the filter paper was regarded as a film while the quartz filter paper was regarded as a substrate to establish a mathematical model for measuring the mass concentration of PM using a photothermal method. The photothermal interferometry system was calibrated and used to measure the atmospheric PM concentration corresponding to different dust-treated filter paper. The measurements were compared to those obtained using β ray method and were found consistent. This method can be particularly relevant to polluted atmospheres where PM is dominated by black carbon.

  17. Electric anisotropy in high density polyethylene + carbon black composites induced by mechanical deformation

    Energy Technology Data Exchange (ETDEWEB)

    Vigueras-Santiago, E; Hernandez-Lopez, S; Camacho-Lopez, M A; Lara-Sanjuan, O, E-mail: eviguerass@uaemex.m [Laboratorio de Investigacion y Desarrollo de Materiales Avanzados (LIDMA), Facultad de Quimica, UAEM. Paseo Colon esq. con Paseo Tollocan, s/n. C.P. 50000, Toluca (Mexico)

    2009-05-01

    High density polyethylene + carbon black composites with electrical anisotropy was studied. Electrical anisotropy was induced by uniaxial mechanical deformation and injection moulding. We show that anisotropy depends on the carbon black concentration and percentage deformation. Resistivity had the highest anisotropy resistivity around the percolation threshold. Perpendicular resistivity showed two magnitude orders higher than parallel resistivity for injected samples, whereas resistivity showed an inverse behaviour for 100% tensile samples. Both directions were set respect to the deformation axe. Anisotropy could be explained in terms of the molecular deformation (alignment) of the polymer chains as a response of the deformation process originating a redistribution of the carbon black particles in both directions. Alignment of the polymer chains was evidenced by polarized Raman spectroscopy.

  18. Dynamic behavior of a black phosphorus and carbon nanotube composite system

    Science.gov (United States)

    Shi, Jiao; Cai, Haifang; Cai, Kun; Qin, Qing-Hua

    2017-01-01

    A double walled nanotube composite is constructed by placing a black-phosphorene-based nanotube (BPNT) in a carbon nanotube (CNT). When driving the CNT to rotate by stators in a thermal driven rotary nanomotor, the BPNT behaves differently from the CNT. For instance, the BPNT can be actuated to rotate by the CNT, but its rotational acceleration differs from that of the CNT. The BPNT oscillates along the tube axis when it is longer than the CNT. The results obtained indicate that the BPNT functions with high structural stability when acting as a rotor with rotational frequency of ~20 GHz at 250 K. If at a higher temperature than 250 K, say 300 K, the rotating BPNT shows weaker structural stability than its status at 250 K. When the two tubes in the rotor are of equal length, the rotational frequency of the BPNT drops rapidly after the BPNT is collapsed, owing to more broken P-P bonds. When the black-phosphorene nanotube is longer than the CNT, it rotates synchronously with the CNT even if it is collapsed. Hence, in the design of a nanomotor with a rotor from BPNT, the working rotational frequency should be lower than a certain threshold at a higher temperature.

  19. The effects of additional black carbon on Arctic sea ice surface albedo: variation with sea ice type and snow cover

    Directory of Open Access Journals (Sweden)

    A. A. Marks

    2013-03-01

    Full Text Available Black carbon in sea ice will decrease sea ice surface albedo through increased absorption of incident solar radiation, exacerbating sea ice melting. Previous literature has reported different albedo responses to additions of black carbon in sea ice and has not considered how a snow cover may mitigate the effect of black carbon in sea ice. Sea ice is predominately snow covered. Visible light absorption and light scattering coefficients are calculated for a typical first year and multi-year sea ice and "dry" and "wet" snow types that suggest black carbon is the dominating absorbing impurity. The albedo response of first year and multi-year sea ice to increasing black carbon, from 1–1024 ng g−1, in a top 5 cm layer of a 155 cm thick sea ice was calculated using the radiative transfer model: TUV-snow. Sea ice albedo is surprisingly unresponsive to black carbon additions up to 100 ng g−1 with a decrease in albedo to 98.7% of the original albedo value due to an addition of 8 ng g−1 of black carbon in first year sea ice compared to an albedo decrease to 99.6% for the same black carbon mass ratio increase in multi-year sea ice. The first year sea ice proved more responsive to black carbon additions than the multi-year ice. Comparison with previous modelling of black carbon in sea ice suggests a more scattering sea ice environment will be less responsive to black carbon additions. Snow layers on sea ice may mitigate the effects of black carbon in sea ice. "Wet" and "dry" snow layers of 0.5, 1, 2, 5 and 10 cm were added onto the sea ice surface and the snow surface albedo calculated with the same increase in black carbon in the underlying sea ice. Just a 0.5 cm layer of snow greatly diminishes the effect of black carbon on surface albedo, and a 2–5 cm layer (less than half the e-folding depth of snow is enough to "mask" any change in surface albedo owing to additional black carbon in sea ice, but not thick enough to ignore the underlying sea ice.

  20. Adsorption removal of acid black 1 from aqueous solution using ordered mesoporous carbon

    Science.gov (United States)

    Peng, Xiaoming; Hu, Xijun; Fu, Dafang; Lam, Frank L. Y.

    2014-03-01

    A novel ordered mesoporous carbon CMK-3 and synthetic CMK-3 containing nitrogen functional groups by ammonia-treated were applied for acid black 1(AB1) dye adsorption. The ammonia-treated(chemical vapor deposition method) before and after CMK-3 were characterized by using a Micrometitics ASAP 2020 surface area analyzer (ASAP 2020), Fourier transform infrared spectrophotometer (FT-IR), X-ray Photoelectron Spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscope (SEM) and equilibrium studies. This result indicates that the prepared CMK-3 and modified CMK-3 were almost uniform, as rope-like domains and their uniform mesopore with diameter centered at 3.2 nm and 3.7 nm. The FIIR analysis depicted that the presence of a variety of new basic functional groups on the modified CMK-3 surface. Several effect variables of pH, dye concentration and temperature were studied. The pseudo second-order model showed the fitter well to agree with the kinetic data. The experimental data were analyzed by the Langmuir and Freundlich models, with the latter found to closely the isotherm model. The adsorption kinetics was found to follow the pseudo-second-order kinetic model. The results show that CMK-3 using ammonia gas modified by thermal treatment system is an effective method to improvement capacity as it shows the highest adsorption capacity of AB1, as compared to the unmodified CMK-3 and the bamboo-based carbon, respectively.

  1. Commuter exposure to black carbon, carbon monoxide, and noise in the mass transport khlong boats of Bangkok, Thailand

    Science.gov (United States)

    Ziegler, A. D.; Velasco, E.; Ho, K. J.

    2013-12-01

    Khlong (canal) boats are a unique mass transport alternative in the congested city of Bangkok. Canals and rivers provide exclusive transit-ways for reducing the commuting time of thousands of city residents daily. However, as a consequence of the service characteristics and boats design and state of repair, they can represent a potential public health risk and an important source of black carbon and greenhouse gases. This work quantifies commuter exposure to black carbon, CO and noise when waiting for and travelling in these diesel fueled boats. Exposure to toxic pollutants and acute noise is similar or worse than for other transportation modes. Mean black carbon concentrations observed at one busy pier and along the main canal were much higher than ambient concentrations at sites impacted by vehicular traffic. Concentrations of CO were similar to those reported for roadside areas of Bangkok. The equivalent continuous sound levels registered at the landing pier were similar to those reported for roadsides, but values recorded inside the boats were significantly higher. We believe that the boat service is a viable alternative mode of mass transport, but public safety could be improved to provide a high quality service, comparable to modern rail systems or emerging bus rapid transit systems. These investments would also contribute to reduce the emission of black carbon and other greenhouse and toxic pollutants.

  2. Offsetting features of climate responses to anthropogenic sulfate and black carbon direct radiative forcings

    Science.gov (United States)

    Ocko, I.; Ramaswamy, V.

    2012-12-01

    The two most prominent anthropogenic aerosols—sulfate and black carbon—affect Earth's radiation budget in opposing ways. Here we examine how these aerosols independently impact the climate, by simulating climate responses from pre-industrial times (1860) to present-day (2000) for isolated sulfate and black carbon direct radiative forcings. The NOAA Geophysical Fluid Dynamics Laboratory CM2.1 global climate model is employed with prescribed distributions of externally mixed aerosols. We find that sulfate and black carbon induce opposite effects for a myriad of climate variables. Sulfate (black carbon) is generally cooling (warming), shifts the ITCZ southward (northward), reduces (enhances) the SH Hadley Cell, enhances (reduces) the NH Hadley Cell, and increases (decreases) total sea ice volume. Individually, sulfate and black carbon affect Hadley Cell circulation more than long-lived greenhouse gases, but the net aerosol effect is a weakened response due to opposite behaviors somewhat canceling out the individual effects. Because anthropogenic aerosols are a critical contributor to Earth's climate conditions, this study has implications for future climate changes as well.

  3. Initial mass function of intermediate mass black hole seeds

    CERN Document Server

    Ferrara, A; Yue, B; Schleicher, D R G

    2014-01-01

    We study the Initial Mass Function (IMF) and host halo properties of Intermediate Mass Black Holes (IMBH, 10^{4-6} Msun) formed inside metal-free, UV illuminated atomic cooling haloes (virial temperature T_vir > 10^4 K) either via the direct collapse of the gas or via an intermediate Super Massive Star (SMS) stage. We achieve this goal in three steps: (a) we derive the gas accretion rate for a proto-SMS to undergo General Relativity instability and produce a direct collapse black hole (DCBH) or to enter the ZAMS and later collapse into a IMBH; (b) we use merger-tree simulations to select atomic cooling halos in which either a DCBH or SMS can form and grow, accounting for metal enrichment and major mergers that halt the growth of the proto-SMS by gas fragmentation. We derive the properties of the host halos and the mass distribution of black holes at this stage, and dub it the "Birth Mass Function"; (c) we follow the further growth of the DCBH due to accretion of leftover gas in the parent halo and compute the...

  4. Functional determinants, index theorems, and exact quantum black hole entropy

    Science.gov (United States)

    Murthy, Sameer; Reys, Valentin

    2015-12-01

    The exact quantum entropy of BPS black holes can be evaluated using localization in supergravity. An important ingredient in this program, that has been lacking so far, is the one-loop effect arising from the quadratic fluctuations of the exact deformation (the QV operator). We compute the fluctuation determinant for vector multiplets and hyper multiplets around Q-invariant off-shell configurations in four-dimensional N=2 supergravity with AdS 2 × S 2 boundary conditions, using the Atiyah-Bott fixed-point index theorem and a subsequent zeta function regularization. Our results extend the large-charge on-shell entropy computations in the literature to a regime of finite charges. Based on our results, we present an exact formula for the quantum entropy of BPS black holes in N=2 supergravity. We explain cancellations concerning 1/8 -BPS black holes in N=8 supergravity that were observed in arXiv:1111.1161. We also make comments about the interpretation of a logarithmic term in the topological string partition function in the low energy supergravity theory.

  5. An index-based approach to assessing recalcitrance and soil carbon sequestration potential of engineered black carbons (biochars).

    Science.gov (United States)

    Harvey, Omar R; Kuo, Li-Jung; Zimmerman, Andrew R; Louchouarn, Patrick; Amonette, James E; Herbert, Bruce E

    2012-02-07

    The ability of engineered black carbons (or biochars) to resist abiotic and, or biotic degradation (herein referred to as recalcitrance) is crucial to their successful deployment as a soil carbon sequestration strategy. A new recalcitrance index, the R(50), for assessing biochar quality for carbon sequestration is proposed. The R(50) is based on the relative thermal stability of a given biochar to that of graphite and was developed and evaluated with a variety of biochars (n = 59), and soot-like black carbons. Comparison of R(50), with biochar physicochemical properties and biochar-C mineralization revealed the existence of a quantifiable relationship between R(50) and biochar recalcitrance. As presented here, the R(50) is immediately applicable to pre-land application screening of biochars into Class A (R(50) ≥ 0.70), Class B (0.50 ≤ R(50) carbon sequestration classes. Class A and Class C biochars would have carbon sequestration potential comparable to soot/graphite and uncharred plant biomass, respectively, whereas Class B biochars would have intermediate carbon sequestration potential. We believe that the coupling of the R(50), to an index-based degradation, and an economic model could provide a suitable framework in which to comprehensively assess soil carbon sequestration in biochars.

  6. Long-term airborne black carbon measurements on a Lufthansa passenger aircraft

    Science.gov (United States)

    Ditas, Jeannine; Su, Hang; Scharffe, Dieter; Wang, Siwen; Zhang, Yuxuan; Brenninkmeijer, Carl; Pöschl, Ulrich; Cheng, Yafang

    2016-04-01

    Aerosol particles containing black carbon are the most absorbing component of incoming solar radiation and exert a significant positive radiative forcing thus forming next to CO² the strongest component of current global warming (Bond, 2013). Nevertheless, the role of black carbon particles and especially their complex interaction with clouds needs further research which is hampered by the limited experimental data, especially observations in the free and upper troposphere, and in the UTLS (upper troposphere and lower stratosphere). Many models underestimate the global atmospheric absorption attributable to black carbon by a factor of almost 3 (Bond, 2013). In August 2014, a single particle soot photometer was included in the extensive scientific payload of the CARIBIC (Civil Aircraft for the Regular Investigation of the atmosphere Based on an Instrument Container) project. CARIBIC is in operation since 1997 (with an interruption for 2002-2005) and carries out systematic observations at 10-12 km altitude. For this a special air freight container combining different instruments is transported on a monthly basis using a Lufthansa Airbus A340-600 passenger aircraft with destinations from 120°W to 120°E and 10°N to 75°N. The container has equipment for trace gas analyses and sampling and aerosol analyses and sampling and is connected to an inlet system that is part of the aircraft which contains a camera and DOAS remote sensing system. The integration of a single particle soot photometer (SP2) offers the possibility for the first long-term measurement of global distribution of black carbon and so far flights up to November 2015 have been conducted with more than 400 flight hours. So far the SP2 measurements have been analysed for flights over four continents from Munich to San Francisco, Sao Paulo, Tokyo, Beijing, Cape Town, Los Angeles and Hong Kong). The first measurements show promising results of black carbon measurements. Background concentrations in the UTLS

  7. Nanohybrid TiO2/carbon black sensor for NO2 gas

    Institute of Scientific and Technical Information of China (English)

    Wei-Jen Liou; Hong-Ming Lin

    2007-01-01

    A nanohybrid sensor of nanosized TiO2-coated carbon black particles, prepared by sol-gel technology for the detection of NO2 gas, has been developed. The response of the electric resistance of the hybrid sensor to NO2 concentration is investigated, showing that the sensitivity of the hybrid sensor is raised as certain ratio of the TiO2 content in the sensor. Easy and cheap to fabricate, the hybrid TiO2/carbon black promises to be a practical sensor for detecting NO2 gas.

  8. Aerosol Absorption by Black Carbon and Dust: Implications of Climate Change and Air Quality in Asia

    Science.gov (United States)

    Chin, Mian

    2010-01-01

    Atmospheric aerosol distributions from 2000 to 2007 are simulated with the global model GOCART to attribute light absorption by aerosol to its composition and sources. We show the seasonal and interannual variations of absorbing aerosols in the atmosphere over Asia, mainly black carbon and dust. and their linkage to the changes of anthropogenic and dust emissions in the region. We compare our results with observations from satellite and ground-based networks, and estimate the importance of black carbon and dust on regional climate forcing and air quality.

  9. Black carbon fractal morphology and short-wave radiative impact: a modelling study

    Directory of Open Access Journals (Sweden)

    M. Kahnert

    2011-11-01

    Full Text Available We investigate the impact of the morphological properties of freshly emitted black carbon aerosols on optical properties and on radiative forcing. To this end, we model the optical properties of fractal black carbon aggregates by use of numerically exact solutions to Maxwell's equations within a spectral range from the UVC to the mid-IR. The results are coupled to radiative transfer computations, in which we consider six realistic case studies representing different atmospheric pollution conditions and surface albedos. The spectrally integrated radiative impacts of black carbon are compared for two different fractal morphologies, which brace the range of recently reported experimental observations of black carbon fractal structures. We also gauge our results by performing corresponding calculations based on the homogeneous sphere approximation, which is commonly employed in climate models. We find that at top of atmosphere the aggregate models yield radiative impacts that can be as much as 2 times higher than those based on the homogeneous sphere approximation. An aggregate model with a low fractal dimension can predict a radiative impact that is higher than that obtained with a high fractal dimension by a factor ranging between 1.1–1.6. Although the lower end of this scale seems like a rather small effect, a closer analysis reveals that the single scattering optical properties of more compact and more lacy aggregates differ considerably. In radiative flux computations there can be a partial cancellation due to the opposing effects of different error sources. However, this cancellation effect can strongly depend on atmospheric conditions and is therefore quite unpredictable. We conclude that the fractal morphology of black carbon aerosols and their fractal parameters can have a profound impact on their radiative forcing effect, and that the use of the homogeneous sphere model introduces unacceptably high biases in radiative impact studies. We

  10. Aerosol Absorption by Black Carbon and Dust: Implications of Climate Change and Air Quality in Asia

    Science.gov (United States)

    Chin, Mian

    2010-01-01

    Atmospheric aerosol distributions from 2000 to 2007 are simulated with the global model GOCART to attribute light absorption by aerosol to its composition and sources. We show the seasonal and interannual variations of absorbing aerosols in the atmosphere over Asia, mainly black carbon and dust. and their linkage to the changes of anthropogenic and dust emissions in the region. We compare our results with observations from satellite and ground-based networks, and estimate the importance of black carbon and dust on regional climate forcing and air quality.

  11. Factors controlling black carbon distribution in the Arctic

    Science.gov (United States)

    Qi, Ling; Li, Qinbin; Li, Yinrui; He, Cenlin

    2017-01-01

    We investigate the sensitivity of black carbon (BC) in the Arctic, including BC concentration in snow (BCsnow, ng g-1) and surface air (BCair, ng m-3), as well as emissions, dry deposition, and wet scavenging using the global three-dimensional (3-D) chemical transport model (CTM) GEOS-Chem. We find that the model underestimates BCsnow in the Arctic by 40 % on average (median = 11.8 ng g-1). Natural gas flaring substantially increases total BC emissions in the Arctic (by ˜ 70 %). The flaring emissions lead to up to 49 % increases (0.1-8.5 ng g-1) in Arctic BCsnow, dramatically improving model comparison with observations (50 % reduction in discrepancy) near flaring source regions (the western side of the extreme north of Russia). Ample observations suggest that BC dry deposition velocities over snow and ice in current CTMs (0.03 cm s-1 in the GEOS-Chem) are too small. We apply the resistance-in-series method to compute a dry deposition velocity (vd) that varies with local meteorological and surface conditions. The resulting velocity is significantly larger and varies by a factor of 8 in the Arctic (0.03-0.24 cm s-1), which increases the fraction of dry to total BC deposition (16 to 25 %) yet leaves the total BC deposition and BCsnow in the Arctic unchanged. This is largely explained by the offsetting higher dry and lower wet deposition fluxes. Additionally, we account for the effect of the Wegener-Bergeron-Findeisen (WBF) process in mixed-phase clouds, which releases BC particles from condensed phases (water drops and ice crystals) back to the interstitial air and thereby substantially reduces the scavenging efficiency of clouds for BC (by 43-76 % in the Arctic). The resulting BCsnow is up to 80 % higher, BC loading is considerably larger (from 0.25 to 0.43 mg m-2), and BC lifetime is markedly prolonged (from 9 to 16 days) in the Arctic. Overall, flaring emissions increase BCair in the Arctic (by ˜ 20 ng m-3), the updated vd more than halves BCair (by ˜ 20 ng m-3

  12. Black hole mass function from gravitational wave measurements

    Science.gov (United States)

    Kovetz, Ely D.; Cholis, Ilias; Breysse, Patrick C.; Kamionkowski, Marc

    2017-05-01

    We examine how future gravitational-wave measurements from merging black holes (BHs) can be used to infer the shape of the black-hole mass function, with important implications for the study of star formation and evolution and the properties of binary BHs. We model the mass function as a power law, inherited from the stellar initial mass function, and introduce lower and upper mass cutoff parametrizations in order to probe the minimum and maximum BH masses allowed by stellar evolution, respectively. We initially focus on the heavier BH in each binary, to minimize model dependence. Taking into account the experimental noise, the mass measurement errors and the uncertainty in the redshift dependence of the merger rate, we show that the mass function parameters, as well as the total rate of merger events, can be measured to years of advanced LIGO observations at its design sensitivity. This can be used to address important open questions such as the upper limit on the stellar mass which allows for BH formation and to confirm or refute the currently observed mass gap between neutron stars and BHs. In order to glean information on the progenitors of the merging BH binaries, we then advocate the study of the two-dimensional mass distribution to constrain parameters that describe the two-body system, such as the mass ratio between the two BHs, in addition to the merger rate and mass function parameters. We argue that several years of data collection can efficiently probe models of binary formation, and show, as an example, that the hypothesis that some gravitational-wave events may involve primordial black holes can be tested. Finally, we point out that in order to maximize the constraining power of the data, it may be worthwhile to lower the signal-to-noise threshold imposed on each candidate event and amass a larger statistical ensemble of BH mergers.

  13. [Effect of long-term fertilization on microbial community functional diversity in black soil].

    Science.gov (United States)

    Liu, Jing-xin; Chi, Feng-qin; Xu, Xiu-hong; Kuang, En-jun; Zhang, Jiu-ming; Su, Qing-rui; Zhou, Bao-ku

    2015-10-01

    In order to study the effects of long-term different fertilization on microbial community functional diversity in arable black. soil, we examined microbial metabolic activities in two soil la- yers (0-20 cm, 20-40 cm) under four treatments (CK, NPK, M, MNPK) from a 35-year continuous fertilization field at the Ministry of Agriculture Key Field Observation Station of Harbin Black Soil Ecology Environment using Biolog-ECO method. The results showed that: in the 0-20 cm soil layer, combined application of organic and inorganic fertilizer(MNPK) increased the rate of soil microbial carbon source utilization and community metabolism richness, diversity and dominance; In the 20-40 cm layer, these indices of the MNPK treatment was lower than that of the NPK treat- ment; while NPK treatment decreased soil microbial community metabolism evenness in both layers. Six groups of carbon sources used by soil microbes of all the treatments were different between the two soil layers, and the difference was significant among all treatments in each soil layer (P functional diversity in both tillage soil layer and down soil layers, and chemical fertilization alone had a larger influence on the microbial community functional diversity in the 20-40 cm layer.

  14. A review on protein functionalized carbon nanotubes.

    Science.gov (United States)

    Nagaraju, Kathyayini; Reddy, Roopa; Reddy, Narendra

    2015-12-18

    Carbon nanotubes (CNTs) have been widely recognized and used for controlled drug delivery and in various other fields due to their unique properties and distinct advantages. Both single-walled carbon nanotubes (SWCNTs) and multiwalled (MWCNTs) carbon nanotubes are used and/or studied for potential applications in medical, energy, textile, composite, and other areas. Since CNTs are chemically inert and are insoluble in water or other organic solvents, they are functionalized or modified to carry payloads or interact with biological molecules. CNTs have been preferably functionalized with proteins because CNTs are predominantly used for medical applications such as delivery of drugs, DNA and genes, and also for biosensing. Extensive studies have been conducted to understand the interactions, cytotoxicity, and potential applications of protein functionalized CNTs but contradicting results have been published on the cytotoxicity of the functionalized CNTs. This paper provides a brief review of CNTs functionalized with proteins, methods used to functionalize the CNTs, and their potential applications.

  15. Solid phase extraction method for the study of black carbon cycling in dissolved organic carbon using radiocarbon

    OpenAIRE

    2015-01-01

    © 2015 Elsevier B.V.. Radiocarbon analysis is a powerful tool for understanding the cycling of individual components within carbon pools, such as black carbon (BC) in dissolved organic carbon (DOC). Radiocarbon (δ14C) measurements of BC in DOC provide insight into one source of aged, recalcitrant DOC. We report a modified solid phase extraction (SPE) method to concentrate 43±6% of DOC (SPE-DOC) from seawater. We used the Benzene Polycarboxylic Acid (BPCA) method to isolate BC from SPE-DOC (SP...

  16. Effect of the secondary organic aerosol coatings on black carbon water uptake, cloud condensation nuclei activity, and particle collapse

    Science.gov (United States)

    The ability of black carbon aerosols to absorb water and act as a cloud condensation nuclei (CCN) directly controls their lifetime in the atmosphere as well as their impact on cloud formation, thus impacting the earth’s climate. Black carbon emitted from most combustion pro...

  17. Effects of carbon blacks with various structures on vulcanization and reinforcement of filled ethylene-propylene-diene rubber

    Directory of Open Access Journals (Sweden)

    2008-10-01

    Full Text Available The effects of carbon blacks on vulcanization and mechanical properties of filled ethylene-propylene-diene rubber (EPDM are investigated, by comparing with five types of rubber-grade carbon blacks. Curing kinetics is studied by rheometer and the results indicate that the curing characteristics are influenced by combination of surface area of carbon black and sulphur content on the filler surface, because the former one enhances the physical cross-linking and the latter one introduces the additional chemical cross-linking. Both the degree of cross-linking and cure rate increase with increasing surface area and sulphur content, whereas the optimum cure time and scorch time decrease. The reinforcing nature of the carbon black is assessed from mechanical measurements. It is suggested that the surface area of carbon blacks strongly affects the physical properties of EPDM/carbon black composites. Conductive carbon black (N472 can be used as desirable reinforcing filler due to the higher degree of cross-linking of EPDM with N472 than other EPDM/carbon black composites. The morphology and distribution of particles are studied by using scanning electron microscope. The sound reinforcing ability of N472 is also supported by scanning electron microscope due to the notable dispersibility of N472 within EPDM matrix. N472 ensures the EPDM/N472 composite the most conductive sample among the five composites.

  18. Surface modification and functionalization of nanostructured carbons

    Directory of Open Access Journals (Sweden)

    A. Stanishevsky

    2009-12-01

    Full Text Available Purpose: Nanostructured carbon nanomaterials (e.g., nanocrystalline diamond films and particles, carbon nanotubes, carbon onions, fullerenes, etc. are being extensively explored for numerous biomedical applications in surgical implants, therapy, drug delivery, and biosensoring due to their interesting physical, chemical, and biological properties. Such applications of carbon nanomaterials often require specific surface functionality to be introduced for better integration of these materials with physiological environment. In the last decade, substantial progress has been made in the development of controllable surface modification methods and in the introduction of different functional groups on the surface of carbon nanomaterials.Design/methodology/approach: This paper briefly overviews the surface modification and functionalization approaches for various carbon nanomaterials, and it focuses on the plasma modification and functionalization of nanocrystalline diamond films, diamond nanoparticles, and carbon nanospheres. The results on the surface characterization using FTIR and XPS techniques, and the preliminary studies of cellular response to these modified carbon nanomaterials are presented and discussed.Findings: The results of surface modification of NCD films, detonation nanodiamonds, and carbon nanospheres, demonstrate the flexibility of nanocarbons to attain various surface functionality that can be adjusted for specific applications. It has been shown that neither of tested nanocarbon materials was cytotoxic in this study, although the attachement and proliferation of various cells was strongly affected by the specific type of surface functionalization.Research limitations/implications: At the present, it is not clear to what degree the available surface sites on NCD films or carbon nanoparticles can be occupied with functional groups. Furthermore, while there is clear selectivity of cellular response to H, O, and F surface

  19. Automatic Method for Controlling the Iodine Adsorption Number in Carbon Black Oil Furnaces

    Directory of Open Access Journals (Sweden)

    Zečević, N.

    2008-12-01

    Full Text Available There are numerous of different inlet process factors in carbon black oil furnaces which must be continuously and automatically adjusted, due to stable quality of final product. The most important six inlet process factors in carbon black oil-furnaces are:1. volume flow of process air for combustion2. temperature of process air for combustion3. volume flow of natural gas for insurance the necessary heat for thermal reaction of conversionthe hydrocarbon oil feedstock in oil-furnace carbon black4. mass flow rate of hydrocarbon oil feedstock5. type and quantity of additive for adjustment the structure of oil-furnace carbon black6. quantity and position of the quench water for cooling the reaction of oil-furnace carbon black.The control of oil-furnace carbon black adsorption capacity is made with mass flow rate of hydrocarbon feedstock, which is the most important inlet process factor. Oil-furnace carbon black adsorption capacity in industrial process is determined with laboratory analyze of iodine adsorption number. It is shown continuously and automatically method for controlling iodine adsorption number in carbon black oil-furnaces to get as much as possible efficient control of adsorption capacity. In the proposed method it can be seen the correlation between qualitatively-quantitatively composition of the process tail gasses in the production of oil-furnace carbon black and relationship between air for combustion and hydrocarbon feedstock. It is shown that the ratio between air for combustion and hydrocarbon oil feedstock is depended of adsorption capacity summarized by iodine adsorption number, regarding to BMCI index of hydrocarbon oil feedstock.The mentioned correlation can be seen through the figures from 1. to 4. From the whole composition of the process tail gasses the best correlation for continuously and automatically control of iodine adsorption number is show the volume fraction of methane. The volume fraction of methane in the

  20. Bounding the role of black carbon in the climate system: A scientific assessment

    Science.gov (United States)

    Bond, T. C.; Doherty, S. J.; Fahey, D. W.; Forster, P. M.; Berntsen, T.; Deangelo, B. J.; Flanner, M. G.; Ghan, S.; KäRcher, B.; Koch, D.; Kinne, S.; Kondo, Y.; Quinn, P. K.; Sarofim, M. C.; Schultz, M. G.; Schulz, M.; Venkataraman, C.; Zhang, H.; Zhang, S.; Bellouin, N.; Guttikunda, S. K.; Hopke, P. K.; Jacobson, M. Z.; Kaiser, J. W.; Klimont, Z.; Lohmann, U.; Schwarz, J. P.; Shindell, D.; Storelvmo, T.; Warren, S. G.; Zender, C. S.

    2013-06-01

    carbon aerosol plays a unique and important role in Earth's climate system. Black carbon is a type of carbonaceous material with a unique combination of physical properties. This assessment provides an evaluation of black-carbon climate forcing that is comprehensive in its inclusion of all known and relevant processes and that is quantitative in providing best estimates and uncertainties of the main forcing terms: direct solar absorption; influence on liquid, mixed phase, and ice clouds; and deposition on snow and ice. These effects are calculated with climate models, but when possible, they are evaluated with both microphysical measurements and field observations. Predominant sources are combustion related, namely, fossil fuels for transportation, solid fuels for industrial and residential uses, and open burning of biomass. Total global emissions of black carbon using bottom-up inventory methods are 7500 Gg yr-1 in the year 2000 with an uncertainty range of 2000 to 29000. However, global atmospheric absorption attributable to black carbon is too low in many models and should be increased by a factor of almost 3. After this scaling, the best estimate for the industrial-era (1750 to 2005) direct radiative forcing of atmospheric black carbon is +0.71 W m-2 with 90% uncertainty bounds of (+0.08, +1.27) W m-2. Total direct forcing by all black carbon sources, without subtracting the preindustrial background, is estimated as +0.88 (+0.17, +1.48) W m-2. Direct radiative forcing alone does not capture important rapid adjustment mechanisms. A framework is described and used for quantifying climate forcings, including rapid adjustments. The best estimate of industrial-era climate forcing of black carbon through all forcing mechanisms, including clouds and cryosphere forcing, is +1.1 W m-2 with 90% uncertainty bounds of +0.17 to +2.1 W m-2. Thus, there is a very high probability that black carbon emissions, independent of co-emitted species, have a positive forcing and warm

  1. The Black Hole Mass Function from Gravitational Wave Measurements

    CERN Document Server

    Kovetz, Ely D; Breysse, Patrick C; Kamionkowski, Marc

    2016-01-01

    We examine how future gravitational-wave measurements from merging black holes (BHs) can be used to infer the shape of the black-hole mass function, with important implications for the study of star formation and evolution and the properties of binary BHs. We model the mass function as a power law, inherited from the stellar initial mass function, and introduce lower and upper mass cutoff parameterizations in order to probe the minimum and maximum BH masses allowed by stellar evolution, respectively. We initially focus on the heavier BH in each binary, to minimize model dependence. Taking into account the experimental noise, the mass measurement errors and the uncertainty in the redshift-dependence of the merger rate, we show that the mass function parameters, as well as the total rate of merger events, can be measured to <10% accuracy within a few years of advanced LIGO observations at its design sensitivity. This can be used to address important open questions such as the upper limit on the stellar mass ...

  2. Functional determinants, index theorems, and exact quantum black hole entropy

    CERN Document Server

    Murthy, Sameer

    2015-01-01

    The exact quantum entropy of BPS black holes can be evaluated using localization in supergravity. An important ingredient in this program, that has been lacking so far, is the one-loop effect arising from the quadratic fluctuations of the exact deformation (the $Q\\mathcal{V}$ operator). We compute the fluctuation determinant for vector multiplets and hyper multiplets around $Q$-invariant off-shell configurations in four-dimensional $\\mathcal{N}=2$ supergravity with $AdS_{2} \\times S^{2}$ boundary conditions, using the Atiyah-Bott fixed-point index theorem and a subsequent zeta function regularization. Our results extend the large-charge on-shell entropy computations in the literature to a regime of finite charges. Based on our results, we present an exact formula for the quantum entropy of BPS black holes in $\\mathcal{N}=2$ supergravity. We explain cancellations concerning $\\frac18$-BPS black holes in $\\mathcal{N}=8$ supergravity that were observed previously. We also make comments about the interpretation of...

  3. Primordial black hole constraints for extended mass functions

    Science.gov (United States)

    Carr, Bernard; Raidal, Martti; Tenkanen, Tommi; Vaskonen, Ville; Veermäe, Hardi

    2017-07-01

    We revisit the cosmological and astrophysical constraints on the fraction of the dark matter in primordial black holes (PBHs) with an extended mass function. We consider a variety of mass functions, all of which are described by three parameters: a characteristic mass and width and a dark matter fraction. Various observations then impose constraints on the dark matter fraction as a function of the first two parameters. We show how these constraints relate to those for a monochromatic mass function, demonstrating that they usually become more stringent in the extended case than the monochromatic one. Considering only the well-established bounds, and neglecting the ones that depend on additional astrophysical assumptions, we find that there are three mass windows, around 5 ×10-16M⊙ , 2 ×10-14M⊙ and 25 - 100 M⊙ , where PBHs can constitute all the dark matter. However, if one includes all the bounds, PBHs can only constitute of order 10% of the dark matter.

  4. Improvement of the Rotary Dryers of Wet Pelletized Oil-Furnace Carbon Blacks

    Directory of Open Access Journals (Sweden)

    Zečević, M

    2010-05-01

    Full Text Available Due to the demand for higher production capacity and natural-gas energy savings, improvements were made to the rotary dryers in the drying process of wet pelletized oil-furnace carbon blacks. Since the rotary dryers were originally designed for drying semi-wet pelletized oil-furnace carbon blacks, they did not entirely satisfy optimal conditions for drying wet pelletized oil-furnace carbon blacks. Figure 1 shows the drying principle with key dimensions. The energy for drying the wet pelletized oil-furnace carbon blacks was provided by natural gas combustion in an open-furnace system with an uncontrolled feed of combustion air. Improvements on the rotary dryers were carried out by adjusting the excess oxygen in the gases passing through the butterfly valve on the dryer exhaust stack. By regulating the butterfly valve on the dryer exhaust stack, and applying the prescribed operations for drying wet pelletized oil furnace carbon blacks, the excess oxygen in the tail gases was adjusted in the range of φ = 3.0 % and 5.0 %, depending on the type of oil-furnace carbon blacks. Suggested also is installation of a direct-reverse automatic butterfly valve on the dryer exhaust stack to automatically determine the volume fraction of oxygen in the tail gas, and the volume flow rate of natural gas for combustion. The results the improvements carried out are shown in Tables 3 to 5. Table 2 shows the thermal calculations for the hood of the rotary dryer. Preheating of the process water in the temperature range of 70 °C and 80 °C is also recommended using the net heat from the oil-furnace process for wet pelletization. The results of preheating the process water are shown in Table 1. Depending on the type of oil-furnace carbon black, the aforementioned improvements resulted in natural gas energy savings ranging from 25 % to 35 % in relation to the average natural gas requirement in the drying process, and thus a reduction in carbon emissions of up to 40

  5. Seasonal and diurnal variations of black carbon and organic carbon aerosols in Bangkok

    Science.gov (United States)

    Sahu, L. K.; Kondo, Y.; Miyazaki, Y.; Pongkiatkul, Prapat; Kim Oanh, N. T.

    2011-08-01

    Measurements of black carbon (BC) and organic carbon (OC) were conducted in Bangkok during 2007-2008. Annual trends of BC and OC show strong seasonality with lower and higher concentrations during wet and dry seasons, respectively. Flow of cleaner air, wet removal, and negligible biomass burning resulted in the lowest concentrations of aerosols in the wet season. In addition to anthropogenic sources, long-range transport and biomass burning caused higher concentrations in the dry and hot seasons, respectively. Despite extensive biomass burning in the hot season, moderate levels of aerosols were due to the mixing with air masses from the Pacific Ocean. Diurnal distributions exhibit peaks during rush hour marked by minima in the OC/BC ratio and stagnant wind flow. The lowest concentrations in the afternoon hours could be due to deeper planetary boundary layer and reduced traffic. Overall, the concentrations of both BC and OC decrease with the increase in wind speed. The weekend effects, due to reduced emission during weekends, in the concentrations of both BC and OC were significant. Therefore, stricter abatement in vehicular emissions could substantially reduce pollution. A slope of ΔBC/ΔCO of 9.8 ngm-3 ppbv-1 for the wet season represents the emission ratio from vehicular sources. The highest of ΔOC/ΔBC (3 μg μg-1) in the hot season was due to the predominant influence of biomass burning and significant formation of secondary OC. The levels of BC and OC in Bangkok fall within the ranges of their concentrations measured in the major cities of East Asia.

  6. Critical review of black carbon and elemental carbon source apportionment in Europe and the United States

    Science.gov (United States)

    Briggs, Nicole L.; Long, Christopher M.

    2016-11-01

    An increasing number of air pollution source apportionment studies in Europe and the United States have focused on the black carbon (BC) fraction of ambient particulate matter (PM) given its linkage with adverse public health and climate impacts. We conducted a critical review of European and US BC source apportionment studies published since 2003. Since elemental carbon (EC) has been used as a surrogate measure of BC, we also considered source apportionment studies of EC measurements. This review extends the knowledge presented in previous ambient PM source apportionment reviews because we focus on BC and EC and critically examine the differences between source apportionment results for different methods and source categories. We identified about 50 BC and EC source apportionment studies that have been conducted in either Europe or the US since 2003, finding a striking difference in the commonly used source apportionment methods between the two regions and variations in the assigned source categories. Using three dominant methodologies (radiocarbon, aethalometer, and macro-tracer methods) that only allow for BC to be broadly apportioned into either fossil fuel combustion or biomass burning source categories, European studies generally support fossil fuel combustion as the dominant ambient BC source, but also show significant biomass burning contributions, in particular in wintertime at non-urban locations. Among US studies where prevailing methods such as chemical mass balance (CMB) and positive matrix factorization (PMF) models have allowed for estimation of more refined source contributions, there are fewer findings showing the significance of biomass burning and variable findings on the relative proportion of BC attributed to diesel versus gasoline emissions. Overall, the available BC source apportionment studies provide useful information demonstrating the significance of both fossil fuel combustion and biomass burning BC emission sources in Europe and the US

  7. Black carbon and carbon monoxide over Bay of Bengal during W_ICARB: Source characteristics

    Science.gov (United States)

    Girach, I. A.; Nair, Vijayakumar S.; Babu, S. Suresh; Nair, Prabha R.

    2014-09-01

    The ship borne measurements of near-surface black carbon (BC) and carbon monoxide (CO) were carried out over Bay of Bengal (BoB) during the winter period of 2009 under W_ICARB, the second phase of ‘Integrated Campaign for Aerosols, gases and Radiation Budget (ICARB)'. The CO mixing ratio and BC mass concentration varied in the ranges of 80-480 ppbv and 75-10,000 ng m-3, respectively over this marine region. The BC and CO showed similar variations over northern BoB where airmass from Indo-Gangetic Plain (IGP) region prevailed during the observations period leading to a very strong positive correlation. The association of BC and CO was poor over the eastern and southern part of BoB could be due to the removal of BC aerosols by rain and/or processes of dilution and mixing while transported over to BoB. The highest value of CO observed over eastern BoB was partially due to biomass burning over East Asia. The BC/CO ratio for IGP airmass found to be 20.3 ng m-3 ppb-1 and ∼16 ng m-3 ppb-1 during winter and pre-monsoon, respectively which indicate the role of biomass burning as the source of BC over the region. Based on the emission flux of CO from various inventories and observed BC/CO ratios during pre-monsoon and winter, the BC emission for India is estimated to be in the range of 0.78-1.23 Tg year-1. The analysis of scavenging of BC revealed the loss rate of BC due to relative humidity 0.39 ± 0.08 ng m-3 ppb-1 RH (%)-1 over northern BoB and 0.53 ± 0.04 ng m-3 ppb-1 RH (%)-1 over the southern-BoB during winter.

  8. Enhanced Activated Carbon Cathode Performance for Microbial Fuel Cell by Blending Carbon Black

    KAUST Repository

    Zhang, Xiaoyuan

    2014-02-04

    Activated carbon (AC) is a useful and environmentally sustainable catalyst for oxygen reduction in air-cathode microbial fuel cells (MFCs), but there is great interest in improving its performance and longevity. To enhance the performance of AC cathodes, carbon black (CB) was added into AC at CB:AC ratios of 0, 2, 5, 10, and 15 wt % to increase electrical conductivity and facilitate electron transfer. AC cathodes were then evaluated in both MFCs and electrochemical cells and compared to reactors with cathodes made with Pt. Maximum power densities of MFCs were increased by 9-16% with CB compared to the plain AC in the first week. The optimal CB:AC ratio was 10% based on both MFC polarization tests and three electrode electrochemical tests. The maximum power density of the 10% CB cathode was initially 1560 ± 40 mW/m2 and decreased by only 7% after 5 months of operation compared to a 61% decrease for the control (Pt catalyst, 570 ± 30 mW/m2 after 5 months). The catalytic activities of Pt and AC (plain or with 10% CB) were further examined in rotating disk electrode (RDE) tests that minimized mass transfer limitations. The RDE tests showed that the limiting current of the AC with 10% CB was improved by up to 21% primarily due to a decrease in charge transfer resistance (25%). These results show that blending CB in AC is a simple and effective strategy to enhance AC cathode performance in MFCs and that further improvement in performance could be obtained by reducing mass transfer limitations. © 2014 American Chemical Society.

  9. Black carbon emission reduction strategies in healthcare industry for effective global climate change management.

    Science.gov (United States)

    Raila, Emilia Mmbando; Anderson, David O

    2017-04-01

    Climate change remains one of the biggest threats to life on earth to date with black carbon (BC) emissions or smoke being the strongest cause after carbon dioxide (CO2). Surprisingly, scientific evidence about black carbon emissions reduction in healthcare settings is sparse. This paper presents new research findings on the reduction of black carbon emissions from an observational study conducted at the UN Peacekeeping Operations (MINUSTAH) in Haiti in 2014. Researchers observed 20 incineration cycles, 30 minutes for each cycle of plastic and cardboard sharps healthcare waste (HCW) containers ranged from 3 to 14.6 kg. The primary aim was to determine if black carbon emissions from healthcare waste incineration can be lowered by mainstreaming the use of cardboard sharps healthcare waste containers instead of plastic sharps healthcare waste containers. Similarly, the study looks into whether burning temperature was associated with the smoke levels for each case or not. Independent samples t-tests demonstrated significantly lower black carbon emissions during the incineration of cardboard sharps containers (6.81 ± 4.79% smoke) than in plastic containers (17.77 ± 8.38% smoke); a statistically significant increase of 10.96% smoke (95% Confidence Interval ( CI) [4.4 to 17.5% smoke], p = 0.003). Correspondingly, lower bottom burner temperatures occurred during the incineration of cardboard sharps containers than in plastic (95% Cl [16 to 126°C], p = 0.014). Finally, we expect the application of the new quantitative evidence to form the basis for policy formulation, mainstream the use of cardboard sharps containers and opt for non-incineration disposal technologies as urgent steps for going green in healthcare waste management.

  10. Black Carbon Flux Across the Himalaya through the Kali Gandaki Valley in Nepal

    Science.gov (United States)

    Dhungel, S.; Panday, A. K.; Mahata, K. S.

    2013-12-01

    Significant increases in black carbon concentration have been observed in the recent years over the Indo-Gangetic plain, the foothills of the Himalaya, as well as the high Himalaya and the Tibetan Plateau. The concentration of increased black carbon can be significantly correlated to the albedo effect and the warming of atmosphere at high altitudes due to the deposition of black carbon in the snow clad mountains. It is hypothesized that this deposition contributes to increased melting of Himalayan glaciers and snowfields. Satellite images show increasing amounts of aerosol haze over the Indo-Gangetic plains which penetrate into the Himalayan valleys. But how does it reach the high altitude of the Himalayan cryosphere? To date, mechanisms of transport upwind of the valley from the Indo-Gangetic plains up to the Himalaya have not been thoroughly investigated. We hypothesize that wind systems in the deep river valleys that cut across the Himalaya, such as the Arun valley and Kali Gandaki valley, serve as important pathways for pollutant transport. In 2010 the University of Virginia, in collaboration with ICIMOD and Nepal Wireless, established an atmospheric research station in Jomsom, Nepal (28.78N, 83.42E, 2900 m.a.s.l.). The station is equipped to measure black carbon (BC), carbon monoxide (CO), and ozone concentrations. It also has an automated weather station, a filter sampler, and a NASA Aeronet Sunphotometer. Here we use our observations in Jomsom to present an estimate of the annual flux of black carbon from the Indo-Gangetic plains to the Tibetan Plateau through the Kali Gandaki valley. In this way, we gain insight into the significance of deep valleys and their role as pathways for pollutant transport.

  11. Patterned functional carbon fibers from polyethylene

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, Marcus A [ORNL; Saito, Tomonori [ORNL; Brown, Rebecca H [ORNL; Kumbhar, Amar S [University of North Carolina, Chapel Hill; Naskar, Amit K [ORNL

    2012-01-01

    Patterned, continuous carbon fibers with controlled surface geometry were produced from a novel melt-processible carbon precursor. This portends the use of a unique technique to produce such technologically innovative fibers in large volume for important applications. The novelties of this technique include ease of designing and fabricating fibers with customized surface contour, the ability to manipulate filament diameter from submicron scale to a couple of orders of magnitude larger scale, and the amenable porosity gradient across the carbon wall by diffusion controlled functionalization of precursor. The geometry of fiber cross-section was tailored by using bicomponent melt-spinning with shaped dies and controlling the melt-processing of the precursor polymer. Circular, trilobal, gear-shaped hollow fibers, and solid star-shaped carbon fibers of 0.5 - 20 um diameters, either in self-assembled bundle form, or non-bonded loose filament form, were produced by carbonizing functionalized-polyethylene fibers. Prior to carbonization, melt-spun fibers were converted to a char-forming mass by optimizing the sulfonation on polyethylene macromolecules. The fibers exhibited distinctly ordered carbon morphologies at the outside skin compared to the inner surface or fiber core. Such order in carbon microstructure can be further tuned by altering processing parameters. Partially sulfonated polyethylene-derived hollow carbon fibers exhibit 2-10 fold surface area (50-500 m2/g) compared to the solid fibers (10-25 m2/g) with pore sizes closer to the inside diameter of the filaments larger than the sizes on the outer layer. These specially functionalized carbon fibers hold promise for extraordinary performance improvements when used, for example, as composite reinforcements, catalyst support media, membranes for gas separation, CO2 sorbents, and active electrodes and current collectors for energy storage applications.

  12. Penelitian pengaruh naphthenic oil dan carbon black terhadap sifat kekerasan lis kaca mobil

    Directory of Open Access Journals (Sweden)

    Any Setyaningsih

    1999-07-01

    Full Text Available This research have a purpose to know influence naphthenic oil and car bon black about properties hardness weather strip for auto mobile. Compound wea ther strip for auto mobile make for Natural Rubber (RSS and sintetic rubber (SBR 1502 with in creasing ingrediens such plasticizer, activator, filler, anti oxidant, accelerator and vulkanizing agent. Compount formula making variation naphthenic oil 3,5 and 7 part along with carbon black 45,50 and 55 part result hardness test with value 67 shore A for compount with naphthenic oil 7 part and carbon black 50 part and after perform make in to fill requrements SNI 1490 – 89 A weather strip auto mobile.

  13. Temporal variations of black carbon during haze and non-haze days in Beijing

    Science.gov (United States)

    Liu, Qingyang; Ma, Tangming; Olson, Michael R.; Liu, Yanju; Zhang, Tingting; Wu, Yu; Schauer, James J.

    2016-09-01

    Black carbon (BC) aerosol has been identified as one of key factors responsible for air quality in Beijing. BC emissions abatement could help slow regional climate change while providing benefits for public health. In order to quantify its variations and contribution to air pollution, we systematically studied real-time measurements of equivalent black carbon (eBC) in PM2.5 aerosols at an urban site in Beijing from 2010 to 2014. Equivalent black carbon (eBC) is used instead of black carbon (BC) for data derived from Aethalometer-31 measurement. Equivalent BC concentrations showed significant temporal variations with seasonal mean concentration varying between 2.13 and 5.97 μg m‑3. The highest concentrations of eBC were found during autumn and winter, and the lowest concentrations occurred in spring. We assessed the temporal variations of eBC concentration during haze days versus non-haze days and found significantly lower eBC fractions in PM2.5 on haze days compared to those on non-haze days. Finally, we observed a clear inverse relationship between eBC and wind speed. Our results show that wind disperses PM2.5 more efficiently than eBC; so, secondary aerosols are not formed to the same degree as primary aerosols over the same transport distance during windy conditions.

  14. Analysis of the Interphase on Carbon Black Formed in High Voltage Batteries

    DEFF Research Database (Denmark)

    Younesi, Reza; Christiansen, Ane Sælland; Scipioni, Roberto

    2015-01-01

    Carbon black (CB) additives commonly used to increase the electrical conductivity of electrodes in Li-ion batteries are generally believed to be electrochemically inert additives in cathodes. Decomposition of electrolyte in the surface region of CB in Li-ion cells at high voltages up to 4.9 V...

  15. Quantification methods of Black Carbon: Comparison of Rock-Eval analysis with traditional methods

    NARCIS (Netherlands)

    Poot, A.; Quik, J.T.K.; Veld, H.; Koelmans, A.A.

    2009-01-01

    Black Carbon (BC) quantification methods are reviewed, including new Rock-Eval 6 data on BC reference materials. BC has been reported to have major impacts on climate, human health and environmental quality. Especially for risk assessment of persistent organic pollutants (POPs) it is important to ac

  16. Effects of prenatal exposure to nanoparticles titanium dioxide and carbon black on female germline DNA stability

    DEFF Research Database (Denmark)

    Boisen, Anne Mette Zenner

    are actively dividing. The aim of this PhD study was to determine if two widely used nanoparticles titanium dioxide UV-Titan and carbon black Printex 90 induce ESTR mutations in the germ cells of prenatally exposed females. Pregnant generation P mice were exposed to ~42 mg UV-Titan/m3/1 h/d during gestation...

  17. Soil Fraction and Black Carbon Particles of Amazonian Dark Earth Harbor Different Fungal Abundance and Diversity

    NARCIS (Netherlands)

    Reis Lucheta, Adriano; Souza Cannavan, F.S.; Tsai, S.M.; Kuramae, E.E.

    2017-01-01

    Amazonian Dark Earth (ADE) is a highly fertile soil of anthropogenic origin characterized by higher amount of charred black carbon (BC). ADE is considered a fertility model, however knowledge about the fungal community structure and diversity inhabiting ADE and BC is scarce. Fungal community

  18. Influence of nanoclay-carbon black hybrid fillers on cure and properties of natural rubber compounds

    NARCIS (Netherlands)

    Sapkota, J.; Poikelispää, M.; Das, A.; Dierkes, W.K.; Vuorinen, J.

    2013-01-01

    The influence of organically modified nanoclay-carbon black (CB) hybrid filler on the curing behavior of natural rubber (NR) was explored in this investigation. Here an effort was paid to understand the curing kinetics of organomodified nanoclay filled rubber compounds. On the basis of two different

  19. Electrical Percolation of Carbon Black Filled Poly (ethylene oxide) Composites in Relation to the Matrix Morphology

    Institute of Scientific and Technical Information of China (English)

    Gen Shui CHENG; Ji Wen HU; Ming Qiu ZHANG; Ming Wei LI; Ding Shu XIAO; Min Zhi RONG

    2004-01-01

    The present work studies the electrical conduction performance of carbon black (CB)filled poly(ethylene oxide) (PEO) composites. The addition of CB leads to reduced matrix crystallinity as the fillers which are partly situated inside the lamellae and hinder the growth of PEO crystallites. As a result, the electrical percolation behavior is related with the matrix morphology.

  20. Evaluation of Methods for the Determination of Black Carbon Emissions from an Aircraft Gas Turbine Engine

    Science.gov (United States)

    The emissions from aircraft gas turbine engines consist of nanometer size black carbon (BC) particles plus gas-phase sulfur and organic compounds which undergo gas-to-particle conversion downstream of the engine as the plume cools and dilutes. In this study, four BC measurement ...

  1. Study of positron annihilation lifetime spectroscopy in carbon black-filled HDPE composite

    CERN Document Server

    Zhang Xian Feng; Zhou Xian Yi; Weng Hu Imin; Ye Bang Jiao; Han Rong Dian; Jia Shao Jin; Zhang Zhi Cheng

    2002-01-01

    The variation of the electrical conductivity of high density polyethylene (HDPE) with the carbon black (CB) content was studied using positron annihilation lifetime spectroscopy (PALS) and free-volume model, the crystallinity of HDPE/CB composite and 'percolation' effect were discussed with measurements of conductivity and DSC test

  2. Investigation of reinforcement of the modified carbon black from wasted tires by nuclear magnetic resonance

    Institute of Scientific and Technical Information of China (English)

    ZHOU Jie; YANG Yong-rong; REN Xiao-hong; STAPF Siegfried

    2006-01-01

    Pyrolysis has the potential of transforming waste into recyclable products. Pyrolytic carbon black (PCB) is one of the most important products from the pyrolysis of used tires. Techniques for surface modifications of PCB have been developed. One of the most significant applications for modified PCB is to reinforce the rubber matrix to obtain high added values. The transverse relaxation and the chain dynamics of vulcanized rubber networks with PCB and modified PCB were studied and compared with those of the commercial carbon blacks using selective 1H transverse relaxation (T2) experiments and dipolar correlation effect (DCE) experiments on the stimulated echo. Demineralization and coupling agent modification not only intensified the interactions between the modified PCB and the neighboring polyisoprene chains, but also increased the chemical cross-link density of the vulcanized rubber with modified PCB. The mechanical testing of the rubbers with different kinds of carbon blacks showed that the maximum strain of the rubber with modified PCB was improved greatly. The mechanical testing results confirmed the conclusion obtained by nuclear magnetic resonance (NMR). PCB modified by the demineralization and NDZ-105 titanate coupling agent could be used to replace the commercial semi-reinforcing carbon black.

  3. Temporal variations of black carbon during haze and non-haze days in Beijing.

    Science.gov (United States)

    Liu, Qingyang; Ma, Tangming; Olson, Michael R; Liu, Yanju; Zhang, Tingting; Wu, Yu; Schauer, James J

    2016-09-16

    Black carbon (BC) aerosol has been identified as one of key factors responsible for air quality in Beijing. BC emissions abatement could help slow regional climate change while providing benefits for public health. In order to quantify its variations and contribution to air pollution, we systematically studied real-time measurements of equivalent black carbon (eBC) in PM2.5 aerosols at an urban site in Beijing from 2010 to 2014. Equivalent black carbon (eBC) is used instead of black carbon (BC) for data derived from Aethalometer-31 measurement. Equivalent BC concentrations showed significant temporal variations with seasonal mean concentration varying between 2.13 and 5.97 μg m(-3). The highest concentrations of eBC were found during autumn and winter, and the lowest concentrations occurred in spring. We assessed the temporal variations of eBC concentration during haze days versus non-haze days and found significantly lower eBC fractions in PM2.5 on haze days compared to those on non-haze days. Finally, we observed a clear inverse relationship between eBC and wind speed. Our results show that wind disperses PM2.5 more efficiently than eBC; so, secondary aerosols are not formed to the same degree as primary aerosols over the same transport distance during windy conditions.

  4. Black carbon and polycyclic aromatic hydrocarbons (PAHs) in surface sediments of China's marginal seas

    Science.gov (United States)

    Kang, Yanju; Wang, Xuchen; Dai, Minhan; Feng, Huan; Li, Anchun; Song, Qian

    2009-05-01

    This study investigates the distribution of black carbon (BC) and its correlation with total polycyclic aromatic hydrocarbons (ΣPAH) in the surface sediments of China’s marginal seas. BC content ranges from cycling in China’s marginal seas.

  5. Nanoscale Interactions between Engineered Nanomaterials and Black Carbon (Biochar) in Soil

    Science.gov (United States)

    An understanding of the interactions between engineered nanomaterials (NMs) and soil constituents, and a comprehension of how these interactions may affect biological uptake and toxicity are currently lacking. Charcoal black carbon is a normal constituent of soils due to fire history, and can be pre...

  6. Effects of occupational exposure to carbon black on peripheral white blood cell counts and lymphocyte subsets

    NARCIS (Netherlands)

    Dai, Yufei; Niu, Yong; Duan, Huawei; Bassig, Bryan A; Ye, Meng; Zhang, Xiao; Meng, Tao; Bin, Ping; Jia, Xiaowei; Shen, Meili; Zhang, Rong; Hu, Wei; Yang, Xiaofa; Vermeulen, Roel; Silverman, Debra; Rothman, Nathaniel; Lan, Qing; Yu, Shanfa; Zheng, Yuxin

    2016-01-01

    The International Agency for Research on Cancer has classified carbon black (CB) as a possible (Group 2B) human carcinogen. Given that most CB manufacturing processes result in the emission of various types of chemicals, it is uncertain if the adverse health effects that have been observed in CB-exp

  7. Distribution and Sources of Black Carbon in the Arctic

    Science.gov (United States)

    Qi, Ling

    The Arctic is warming at twice the global rate over recent decades. To slow down this warming trend, there is growing interest in reducing the impact from short-lived climate forcers, such as black carbon (BC), because the benefits of mitigation are seen more quickly relative to CO2 reduction. To propose efficient mitigation policies, it is imperative to improve our understanding of BC distribution in the Arctic and to identify the sources. In this dissertation, we investigate the sensitivity of BC in the Arctic, including BC concentrations in snow (BCsnow) and BC concentrations in air (BCair), to emissions, dry deposition and wet scavenging using a global 3-D chemical transport model (CTM) GEOS-Chem. By including flaring emissions, estimating dry deposition velocity using resistance-in-series method, and including Wegener-Bergeron-Findeisen (WBF) in wet scavenging, simulated BCsnow in the eight Arctic sub-regions agree with the observations within a factor of two, and simulated BCair fall within the uncertainty range of observations. Specifically, we find that natural gas flaring emissions in Western Extreme North of Russia (WENR) strongly enhance BCsnow (by up to ?50%) and BCair (by 20-32%) during snow season in the so-called 'Arctic front', but has negligible impact on BC in the free troposphere. The updated dry deposition velocity over snow and ice is much larger than those used in most of global CTMs and agrees better with observation. The resulting BCsnow changes marginally because of the offsetting of higher dry and lower wet deposition fluxes. In contrast, surface BCair decreases strongly due to the faster dry deposition (by 27-68%). WBF occurs when the environmental vapor pressure is in between the saturation vapor pressure of ice crystals and water drops in mixed-phase clouds. As a result, water drops evaporate and releases BC particles in them back into the interstitial air. In most CTMs, WBF is either missing or represented by a uniform and low BC

  8. Effect of carbon black nanoparticles on methane/air explosions: Influence at low initial turbulence

    Science.gov (United States)

    Torrado, David; Glaude, Pierre-Alexandre; Dufaud, Olivier

    2017-06-01

    Nanoparticles are widely used in industrial applications as additives to modify materials properties such as resistance, surface, rheology or UV-radiation. As a consequence, the quantification and characterization of nanoparticles have become almost compulsory, including the understanding of the risks associated to their use. Since a few years ago, several studies of dust explosion properties involving nano-sized powder have been published. During the production and industrial use of nanoparticles, simultaneous presence of gas / vapor / solvents and dispersed nanoparticles mixtures might be obtained, increasing the risk of a hybrid mixture explosion. The aim of this work is to study the severity of the explosion of carbon black nanoparticles/methane mixtures and understand the influence of adding nanopowders on the behavior of the gas explosions. These results are also useful to understand the influence of soot on the efficiency of the gas combustion. Two grades of carbon black nanoparticles (ranging from 20 to 300 nm average diameter) have been mixed with methane. Tests have been performed on these mixtures in a standard 20 L explosion sphere. Regarding the scale precision, the lowest concentration of carbon black nanoparticles was set at 0.5 g.m-3. Tests were also performed at 2.5 g.m-3, which is still far below 60 g.m-3, the minimum explosive concentration of such powders previously determined in our laboratory. The influence of carbon black particles on the severity of the explosions has been compared to that of pure gas. It appears that the use of carbon black nanoparticles increases the explosion overpressure for lean methane mixtures at low initial turbulences by c. 10%. Similar results were obtained for high initial turbulent systems. Therefore, it seems that carbon black nanoparticles have an impact on the severity of the explosion even for quiescent systems, as opposed to systems involving micro-sized powders that require dispersion at high turbulence

  9. Functionalized carbon nanotubes for potential medicinal applications.

    Science.gov (United States)

    Zhang, Yi; Bai, Yuhong; Yan, Bing

    2010-06-01

    Functionalized carbon nanotubes display unique properties that enable a variety of medicinal applications, including the diagnosis and treatment of cancer, infectious diseases and central nervous system disorders, and applications in tissue engineering. These potential applications are particularly encouraged by their ability to penetrate biological membranes and relatively low toxicity. High aspect ratio, unique optical property and the likeness as small molecule make carbon nanotubes an unusual allotrope of element carbon. After functionalization, carbon nanotubes display potentials for a variety of medicinal applications, including the diagnosis and treatment of cancer, infectious diseases and central nervous system disorders, and applications in tissue engineering. These potential applications are particularly encouraged by their ability to penetrate biological membranes and relatively low toxicity.

  10. Morphology and Optical Properties of Black-Carbon Particles Relevant to Engine Emissions

    Science.gov (United States)

    Michelsen, H. A.; Bambha, R.; Dansson, M. A.; Schrader, P. E.

    2013-12-01

    Black-carbon particles are believed to have a large influence on climate through direct radiative forcing, reduction of surface albedo of snow and ice in the cryosphere, and interaction with clouds. The optical properties and morphology of atmospheric particles containing black carbon are uncertain, and characterization of black carbon resulting from engines emissions is needed. Refractory black-carbon particles found in the atmosphere are often coated with unburned fuel, sulfuric acid, water, ash, and other combustion by-products and atmospheric constituents. Coatings can alter the optical and physical properties of the particles and therefore change their optical properties and cloud interactions. Details of particle morphology and coating state can also have important effects on the interpretation of optical diagnostics. A more complete understanding of how coatings affect extinction, absorption, and incandescence measurements is needed before these techniques can be applied reliably to a wide range of particles. We have investigated the effects of coatings on the optical and physical properties of combustion-generated black-carbon particles using a range of standard particle diagnostics, extinction, and time-resolved laser-induced incandescence (LII) measurements. Particles were generated in a co-flow diffusion flame, extracted, cooled, and coated with oleic acid. The diffusion flame produces highly dendritic soot aggregates with similar properties to those produced in diesel engines, diffusion flames, and most natural combustion processes. A thermodenuder was used to remove the coating. A scanning mobility particle sizer (SMPS) was used to monitor aggregate sizes; a centrifugal particle mass analyzer (CPMA) was used to measure coating mass fractions, and transmission electron microscopy (TEM) was used to characterize particle morphologies. The results demonstrate important differences in optical measurements between coated and uncoated particles.

  11. Characterisation of surface ionisation and adsorption of phenol and 4-nitrophenol on non-porous carbon blacks

    OpenAIRE

    Carrott, Peter; Carrott, Manuela; Vale, Tania; Valente Nabais, Joao; Mourao, Paulo

    2008-01-01

    The adsorption of phenol and 4-nitrophenol from aqueous solutions by carbon blacks was studied. Particular attention was paid to the characterisation of the surface chemistry and ionisation of the carbon blacks by use of a simple carbon surface ionisation model, as well as the use of a normalised form of the Freundlich equation for the analysis of the adsorption isotherms. The results indicated that the solutes interact directly with the graphene layers and that the adsorpti...

  12. Cope, Conform, or Resist? Functions of a Black American Identity at a Predominantly White University

    Science.gov (United States)

    Payne, Yasser Arafat; Suddler, Carl

    2014-01-01

    This study organized five black American undergraduate students into a participatory action research (PAR) team to examine Cross and Strauss' (1998) and Cross, Smith, and Payne's (2002) functions of blackness theory (i.e., bonding, code switching, and individualism) within a sample of black American students, frontline staff (i.e.,…

  13. Low-wind and other microclimatic factors in near-road black carbon variability: A case study and assessment implications

    Science.gov (United States)

    Liang, Marissa S.; Keener, Timothy C.; Birch, M. Eileen; Baldauf, Richard; Neal, Jill; Yang, Y. Jeffrey

    2013-12-01

    Airborne black carbon from urban traffic is a climate forcing agent and has been associated with health risks to near-road populations. In this paper, we describe a case study of black carbon concentration and compositional variability at and near a traffic-laden multi-lane highway in Cincinnati, Ohio, using an onsite aethalometer and filter-based NIOSH Method 5040 measurements; the former measured 1-min average black carbon concentrations and the latter determined the levels of organic and elemental carbon (OC and EC) averaged over an approximately 2-h time interval. The results show significant wind and temperature effects on black carbon concentration and composition in a way more complex than predicted by Gaussian dispersion models. Under oblique low winds, namely ux[=u×sin(θ)]˜ (0, -0.5 m s-1), which mostly occurred during morning hours, black carbon concentrations per unit traffic flow were highest and had large variation. The variability did not always follow Gaussian dispersion but was characteristic of a uniform distribution at a near-road distance. Under all other wind conditions, the near-road black carbon variation met Gaussian dispersion characteristics. Significant differences in roadside dispersion are observed between OC and EC fractions, between PM2.5 and PM10-2.5, and between the morning period and rest of the day. In a general case, the overall black carbon variability at the multi-lane highway can be stated as bimodal consisting of Gaussian dispersion and non-Gaussian uniform distribution. Transition between the two types depends on wind velocity and wind angle to the traffic flow. In the order of decreasing importance, the microclimatic controlling factors over the black carbon variability are: 1) wind velocity and the angle with traffic; 2) diurnal temperature variations due to thermal buoyancy; and 3) downwind Gaussian dispersion. Combinations of these factors may have created various traffic-microclimate interactions that have significant

  14. Advanced technology for functionalization of carbon nanotubes

    Institute of Scientific and Technical Information of China (English)

    Lingjie Meng; Chuanlong Fu; Qinghua Lu

    2009-01-01

    Functionalization of carbon nanotubes (CNTs) has attracted considerable interest in the fields of physics, chemistry, material science and biology. The functionalized CNTs exhibit improved properties enabling facile fabrication of novel nanomaterials and nanodevices. Most of the functionalization approaches developed at present could be categorized into the covalent attachment of functional groups and the non-covalent adsorption of various functional molecules onto the surface of CNTs. This review highlights recent development and our work in functionalization of carbon nanotubes, leading to bio-compatible CNTs, fluorescent CNTs and transition metal func-tionalizcd CNTs. These novel methods possess advantages such as simplified technical procedures and reduced cost of novel nanoma-terials and nanodcvices fabrication.

  15. Attribution of aerosol light absorption to black carbon, brown carbon, and dust in China – interpretations of atmospheric measurements during EAST-AIRE

    Directory of Open Access Journals (Sweden)

    B. J. Huebert

    2008-06-01

    Full Text Available Black carbon, brown carbon, and mineral dust are three of the most important light absorbing aerosols. Their optical properties differ greatly and are distinctive functions of the wavelength of light. Most optical instruments that quantify light absorption, however, are unable to distinguish one type of absorbing aerosol from another. It is thus instructive to separate total absorption from these different light absorbers to gain a better understanding of the optical characteristics of each aerosol type. During the EAST-AIRE (East Asian Study of Tropospheric Aerosols: an International Regional Experiment campaign near Beijing, we measured light scattering using a nephelometer, and light absorption using an aethalometer and a particulate soot absorption photometer. We also measured the total mass concentrations of carbonaceous (elemental and organic carbon and inorganic particulates, as well as aerosol number and mass distributions. We were able to identify periods during the campaign that were dominated by dust, biomass burning, fresh (industrial chimney plumes, other coal burning pollution, and relatively clean (background air for Northern China. Each of these air masses possessed distinct intensive optical properties, including the single scatter albedo and Ångstrom exponents. Based on the wavelength-dependence and particle size distribution, we apportioned total light absorption to black carbon, brown carbon, and dust; their mass absorption efficiencies at 550 nm were estimated to be 9.5, 0.5, and 0.03 m2/g, respectively. While agreeing with the common consensus that BC is the most important light absorber in the mid-visible, we demonstrated that brown carbon and dust could also cause significant absorption, especially at shorter wavelengths.

  16. Role of black carbon electrical conductivity in mediating hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) transformation on carbon surfaces by sulfides.

    Science.gov (United States)

    Xu, Wenqing; Pignatello, Joseph J; Mitch, William A

    2013-07-02

    Recent research has demonstrated that black carbons catalyze the transformation of a range of nitrated explosives sorbed to the carbon surfaces in the presence of sulfides. Although surface oxygenated functional groups, particularly quinones, and electrical conductivity have both been hypothesized to promote these reactions, the importance of these properties has not been tested. In this work, the importance of electrical conductivity was addressed by producing chars of increasing electrical conductivity via pyrolysis of wood shavings at increasing temperature. The reactivity of chars with respect to transformation of the explosive RDX in the presence of sulfides correlated with electrical conductivity. Oxygenated functional groups were apparently not involved, as demonstrated by the elimination of reactivity of an activated carbon after ozone treatment or sorption of model quinones to the activated carbon surface. Although RDX transformation correlated with char electrical conductivity, no RDX transformation was observed when RDX was physically separated from sulfides but electrically connected through an electrochemical cell. RDX transformation occurred in the presence of a surface-associated sulfur species. The correlation with char electrical conductivity suggests that sulfides are oxidized on carbon surfaces to products that serve as potent nucleophiles promoting RDX transformation.

  17. Mechanical properties of functionalized carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Z Q; Liu, B; Chen, Y L; Hwang, K C [FML, Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China); Jiang, H [Department of Mechanical and Aerospace Engineering, Arizona State University, Tempe, AZ 85287 (United States); Huang, Y [Department of Civil and Environmental Engineering, Northwestern University, Evanston, IL 60208 (United States)], E-mail: liubin@tsinghua.edu.cn, E-mail: y-huang@northwestern.edu

    2008-10-01

    Carbon nanotubes (CNTs) used to reinforce polymer matrix composites are functionalized to form covalent bonds with the polymer in order to enhance the CNT/polymer interfaces. These bonds destroy the perfect atomic structures of a CNT and degrade its mechanical properties. We use atomistic simulations to study the effect of hydrogenization on the mechanical properties of single-wall carbon nanotubes. The elastic modulus of CNTs gradually decreases with the increasing functionalization (percentage of C-H bonds). However, both the strength and ductility drop sharply at a small percentage of functionalization, reflecting their sensitivity to C-H bonds. The cluster C-H bonds forming two rings leads to a significant reduction in the strength and ductility. The effect of carbonization has essentially the same effect as hydrogenization.

  18. Measurements of Black Carbon and aerosol absorption during global circumnavigation and Arctic campaigns

    Science.gov (United States)

    Močnik, Griša; Drinovec, Luka; Vidmar, Primož; Lenarčič, Matevž

    2015-04-01

    During two flight campaigns: around the world (2012) and over the Arctic (2013) we demonstrated the feasibility of scientific research and aerial measurements of aerosolized Black Carbon with ultra-light aircraft. Conducted measurements provided first ever information on Black Carbon concentrations and sources over such a large area at altitude. Ground-level measurements of atmospheric aerosols are routinely performed around the world, but there exists very little data on their vertical and geographical distribution in the global atmosphere. These data is a crucial requirement for our understanding of the dispersion of pollutant species of anthropogenic origin, and their possible effects on radiative forcing, cloud condensation, and other phenomena which can contribute to adverse outcomes. Light absorbing carbonaceous aerosols and black carbon (BC) in particular are a unique tracer for combustion emissions, and can be detected rapidly and with great sensitivity by filter-based optical methods. A single-seat ultra-light aircraft flew around the world and on a Arctic expedition. The flights covered all seven continents; crossed all major oceans; and operated at altitudes around 3000 m ASL and up to 8900 m ASL. The aircraft carried a specially-developed high-sensitivity miniaturized dual-wavelength Aethalometer, which recorded BC concentrations with very high temporal resolution and sensitivity [1, 2]. We present examples of data from flight tracks over remote oceans, uninhabited land masses, and densely populated areas. Measuring the dependence of the aerosol absorption on the wavelength, we show that aerosols produced during biomass combustion can be transported to high altitude in high concentrations and we estimate the underestimation of the direct forcing by models assuming a simple linear relationship between BC concentration and forcing in comparison to observations [3,4]. 1. , Carbon Sampling Takes Flight, Science 2012, 335, 1286. 2. G. Močnik, L. Drinovec, M

  19. Design and synthesis of palladium/graphitic carbon nitride/carbon black hybrids as high-performance catalysts for formic acid and methanol electrooxidation

    Science.gov (United States)

    Qian, Huayu; Huang, Huajie; Wang, Xin

    2015-02-01

    Here we report a facile two-step method to synthesize high-performance palladium/graphitic carbon nitride/carbon black (Pd/g-C3N4/carbon black) hybrids for electrooxidizing formic acid and methanol. The coating of g-C3N4 on carbon black surface is realized by a low-temperature heating treatment, followed by the uniform deposition of palladium nanoparticles (Pd NPs) via a wet chemistry route. Owning to the significant synergistic effects of the individual components, the preferred Pd/g-C3N4/carbon black electrocatalyst exhibits exceptional forward peak current densities as high as 2155 and 1720 mA mg-1Pd for formic acid oxidation in acid media and methanol oxidation in alkaline media, respectively, far outperforming the commercial Pd-C catalyst. The catalyst also shows reliable stability, demonstrating that the newly-designed hybrids have great promise in constructing high-performance portable fuel cell systems.

  20. Soil Organic Carbon, Black Carbon, and Enzyme Activity Under Long-Term Fertilization

    Institute of Scientific and Technical Information of China (English)

    SHAO Xing-hua; ZHENG Jian-wei

    2014-01-01

    The present study aims to understand the effects of long-term fertilization on soil organic carbon (SOC), black carbon (BC), enzyme activity, and the relationships among these parameters. Paddy ifeld was continuously fertilized over 30 yr with nine different fertilizer treatments including N, P, K, NP, NK, NPK, 2NPK (two-fold NPK), NPK+manure (NPKM), and CK (no fertilization), N, 90 kg urea-N ha-1 yr-1; P, 45 kg triple superphosphate-P2O5 ha-1 yr-1; K, 75 kg potassium chloride-K2O ha-1 yr-1;and pig manure, 22 500 kg ha-1 yr-1. Soil samples were collected and determined for SOC, BC content, and enzyme activity. The results showed that the SOC in the NPKM treatment was signiifcantly higher than those in the K, P, and CK treatments. The lowest SOC content was found in the CK treatment. SOC content was similar in the N, NP, NK, NPK, 2NPK, and NPKM treatments. There was no signiifcant difference in BC content among different treatments. The BC-to-SOC ratios (BC/SOC) ranged from 0.50 to 0.63, suggesting that BC might originate from the same source. Regarding enzyme activity, NPK treatment had higher urease activity than NPKM treatment. The urease activity of NPKM treatment was signiifcantly higher than that of 2NPK, NP, N, P, K, CK, and NPKM treatment which produced higher activities of acid phosphatase, catalase, and invertase than all other treatments. Our results indicated that long-term fertilization did not signiifcantly affect BC content. Concurrent application of manure and mineral fertilizers increased SOC content and signiifcantly enhanced soil enzyme activities. Correlation analysis showed that catalase activity was signiifcantly associated with invertase activity, but SOC, BC, and enzyme activity levels were not signiifcantly correlated with one another. No signiifcant correlations were observed between BC and soil enzymes. It is unknown whether soil enzymes play a role in the decomposition of BC.

  1. Preparation polystyrene/multiwalled carbon nanotubes nanocomposites by copolymerization of styrene and styryl-functionalized multiwalled carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Hua, Jing, E-mail: huajing72@qust.edu.cn [Key Laboratory of Rubber-Plastics Ministry of Education, Qingdao University of Science and Technology, Qingdao (China); Wang, Zhongguang; Xu, Ling; Wang, Xin; Zhao, Jian; Li, Feifei [Key Laboratory of Rubber-Plastics Ministry of Education, Qingdao University of Science and Technology, Qingdao (China)

    2013-01-15

    Styryl-functionalized multiwalled carbon nanotubes (p-MWNTs) were prepared by esterification based on the carboxylate salt of carbon nanotubes and p-chloromethylstyrene in toluene. Then in situ radical copolymerization of p-MWNTs and styrene initiated by 2,2 Prime -azobis(isobutyronitrile) (AIBN) was applied to synthesize composites of styryl-functionalized multiwalled carbon nanotubes and polystyrene (PS) (p-MWNTs/PS). Characterizations carried out by FT-IR, {sup 1}H NMR, UV-vis show that styryl group covalently bond to the surface of MWNTs. The results of UV showed that the solutions of p-MWNTs/PS in chloroform have the hyperchromic effect. Transmission electron microscopy (TEM) images of p-MWNTs/PS composites and scanning electron microscopy (SEM) images of fracture surface of p-MWNTs/PS composites showed the functionalized nanotubes had a better dispersion than that of the unfunctionalized MWNTs in the matrix. The results of thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) suggested that the thermal stability of p-MWNTs/PS composites improved in the presence of MWNTs. -- Highlights: Black-Right-Pointing-Pointer A facile and simple way to successfully prepare the polystyrene/MWNTs nanocomposites. Black-Right-Pointing-Pointer Characterizations show that styryl group covalently bond to the surface of MWNTs. Black-Right-Pointing-Pointer The solutions of p-MWNTs/PS in chloroform have the hyperchromic effect. Black-Right-Pointing-Pointer Thermal stability of p-tpas composites improved in the presence of MWNTs. Black-Right-Pointing-Pointer The performance of polymer prepared by this method have great potential for exploitation.

  2. Hydrogen production using thermocatalytic decomposition of methane on Ni30/activated carbon and Ni30/carbon black.

    Science.gov (United States)

    Srilatha, K; Viditha, V; Srinivasulu, D; Ramakrishna, S U B; Himabindu, V

    2016-05-01

    Hydrogen is an energy carrier of the future need. It could be produced from different sources and used for power generation or as a transport fuel which mainly in association with fuel cells. The primary challenge for hydrogen production is reducing the cost of production technologies to make the resulting hydrogen cost competitive with conventional fuels. Thermocatalytic decomposition (TCD) of methane is one of the most advantageous processes, which will meet the future demand, hence an attractive route for COx free environment. The present study deals with the production of hydrogen with 30 wt% of Ni impregnated in commercially available activated carbon and carbon black catalysts (samples coded as Ni30/AC and Ni30/CB, respectively). These combined catalysts were not attempted by previous studies. Pure form of hydrogen is produced at 850 °C and volume hourly space velocity (VHSV) of 1.62 L/h g on the activity of both the catalysts. The analysis (X-ray diffraction (XRD)) of the catalysts reveals moderately crystalline peaks of Ni, which might be responsible for the increase in catalytic life along with formation of carbon fibers. The activity of carbon black is sustainable for a longer time compared to that of activated carbon which has been confirmed by life time studies (850 °C and 54 sccm of methane).

  3. Time-resolved analysis of particle emissions from residential biomass combustion - Emissions of refractory black carbon, PAHs and organic tracers

    Science.gov (United States)

    Nielsen, Ingeborg E.; Eriksson, Axel C.; Lindgren, Robert; Martinsson, Johan; Nyström, Robin; Nordin, Erik Z.; Sadiktsis, Ioannis; Boman, Christoffer; Nøjgaard, Jacob K.; Pagels, Joakim

    2017-09-01

    Time-resolved particle emissions from a conventional wood stove were investigated with aerosol mass spectrometry to provide links between combustion conditions, emission factors, mixing state of refractory black carbon and implications for organic tracer methods. The addition of a new batch of fuel results in low temperature pyrolysis as the fuel heats up, resulting in strong, short-lived, variable emission peaks of organic aerosol-containing markers of anhydrous sugars, such as levoglucosan (fragment at m/z 60). Flaming combustion results in emissions dominated by refractory black carbon co-emitted with minor fractions of organic aerosol and markers of anhydrous sugars. Full cycle emissions are an external mixture of larger organic aerosol-dominated and smaller thinly coated refractory black carbon particles. A very high burn rate results in increased full cycle mass emission factors of 66, 2.7, 2.8 and 1.3 for particulate polycyclic aromatic hydrocarbons, refractory black carbon, total organic aerosol and m/z 60, respectively, compared to nominal burn rate. Polycyclic aromatic hydrocarbons are primarily associated with refractory black carbon-containing particles. We hypothesize that at very high burn rates, the central parts of the combustion zone become air starved, leading to a locally reduced combustion temperature that reduces the conversion rates from polycyclic aromatic hydrocarbons to refractory black carbon. This facilitates a strong increase of polycyclic aromatic hydrocarbons emissions. At nominal burn rates, full cycle emissions based on m/z 60 correlate well with organic aerosol, refractory black carbon and particulate matter. However, at higher burn rates, m/z 60 does not correlate with increased emissions of polycyclic aromatic hydrocarbons, refractory black carbon and organic aerosol in the flaming phase. The new knowledge can be used to advance source apportionment studies, reduce emissions of genotoxic compounds and model the climate impacts of

  4. Hydrogen and Carbon Black Production from the Degradation of Methane by Thermal Plasma

    Directory of Open Access Journals (Sweden)

    Leila Cottet

    2014-05-01

    Full Text Available Methane gas (CH4 is the main inducer of the so called greenhouse gases effect. Recent scientific research aims to minimize the accumulation of this gas in the atmosphere and to develop processes capable of producing stable materials with added value. Thermal plasma technology is a promising alternative to these applications, since it allows obtaining H2 and solid carbon from CH4, without the parallel formation of byproducts such as CO2 and NOx. In this work, CH4 was degraded by thermal plasma in order to produce hydrogen (H2 and carbon black. The degradation efficiency of CH4, selectivity for H2 production as well as the characterization of carbon black were studied. The best results were obtained in the CH4 flow rate of 5 L min-1 the degradation percentage and the selectivity for H2 production reached 98.8 % and 48.4 %, respectively. At flow rates of less than 5 L min-1 the selectivity for H2 production increases and reaches 91.9 %. The carbon black has obtained amorphous with hydrophobic characteristics and can be marketed to be used in composite material, and can also be activated chemically and/or physically and used as adsorbent material.

  5. Black carbon fractal morphology and short-wave radiative impact: a modelling study

    Directory of Open Access Journals (Sweden)

    M. Kahnert

    2011-08-01

    Full Text Available We investigate the impact of the morphological properties of freshly emitted black carbon aerosols on optical properties and on radiative forcing. To this end, we model the optical properties of fractal black carbon aggregates by use of numerically exact solutions to Maxwell's equations within a spectral range from the UVC to the mid-IR. The results are coupled to radiative transfer computations, in which we consider six realistic case studies representing different atmospheric pollution conditions and surface albedos. The spectrally integrated radiative impacts of black carbon are compared for two different fractal morphologies, which brace the range of recently reported experimental observations of black carbon fractal structures. We also gauge our results by performing corresponding calculations based on the homogeneous sphere approximation, which is commonly employed in climate models. We find that at top of atmosphere the aggregate models yield radiative impacts that can be as much as 2 times higher than those based on the homogeneous sphere approximation. An aggregate model with a low fractal dimension can predict a radiative impact that is higher than that obtained with a high fractal dimension by a factor ranging between 1.1–1.6. Although the lower end of this scale seems like a rather small effect, a closer analysis reveals that the single scattering optical properties of more compact and more lacy aggregates differ considerably. In radiative flux computations there can be a partial cancellation due to the opposing effects of differences in the optical cross sections and asymmetry parameters. However, this cancellation effect can strongly depend on atmospheric conditions and is therefore quite unpredictable. We conclude that the fractal morphology of black carbon aerosols and their fractal parameters can have a profound impact on their radiative forcing effect, and that the use of the homogeneous sphere model introduces unacceptably

  6. Abundance, distribution, and isotopic composition of particulate black carbon in the northern Gulf of Mexico

    Science.gov (United States)

    Yang, Weifeng; Guo, Laodong

    2014-11-01

    There exists increasing evidence supporting the important role of black carbon in global carbon cycles. Particulate black carbon (PBC) is allochthonous and has distinct reactivities compared to the bulk particulate organic carbon (tot-POC) in marine environments. However, the abundance, geochemical behavior of PBC and its importance in oceanic carbon budget remain poorly understood. Here we report the abundance, distribution, and stable isotopic signatures of BC derived from the chemo-thermal oxidation (CTO-375) method (BCCTO) in the Gulf of Mexico. Our results show that BCCTO abundance decreased from shelf to basin, and more than a half of riverine BCCTO could be removed over the shelf. Moreover, BCCTO is much more refractory compared to the tot-POC and has δ13C values lower than those of BC-excluded POC. These results highlight the significance of PBC in marine carbon cycles and potentially suggest the need for a new end-member term in quantifying POC sources in the ocean.

  7. An Investigation of the Effects of Black Carbon on Precipitation in the Western United States

    Science.gov (United States)

    Tseng, Hsien-Liang Rose

    Black carbon (BC), the byproduct of incomplete combustion, is considered to be the second most important anthropogenic climate forcing agent after carbon dioxide. BC warms the atmosphere by absorbing solar radiation (direct effect), alters cloud and precipitation formation by acting as cloud condensation nuclei (indirect effect), and modifies cloud distribution via cloud burn-off (semi-direct effect). Currently, there are large discrepancies in general circulation model estimates of the influence of BC on precipitation. Even less known is how BC changes precipitation on regional scales. In the drought-stricken western United States (WUS), where BC emissions are known to affect the hydrological cycle, an investigation on how BC influences precipitation is warranted. In this study, we employ the Weather Research and Forecasting-Chemistry (WRF Chem) model (version 3.6.0) with the newly chemistry- and microphysics-coupled Fu-Liou-Gu radiation scheme to study how black carbon affects precipitation by separating BC-related effects into direct and semi-direct, and indirect effects. In this three-part study, we use a recent wet year (2005) to investigate black carbon effects. We first examine BC effects during a heavy wintertime heavy precipitation event (7-11 January 2005), a heavy summertime precipitation week for comparison to the wintertime event (20-24 July 2005), and finally, examine these same effects for the months of January to June 2005 to investigate month-long trends. We find that BC suppresses precipitation, predominantly through its direct and semi-direct effects. The direct and semi-direct effects warm the air aloft, and cool the lower levels of the atmosphere (surface dimming) through the reduction of downward shortwave radiation flux at the surface. These changes in vertical temperature increase the stability of the atmosphere and reduce convective precipitation. Convective precipitation reduction accounts for approximately 60 75% of the total

  8. Effective density of Aquadag and fullerene soot black carbon reference materials used for SP2 calibration

    Directory of Open Access Journals (Sweden)

    M. Gysel

    2011-08-01

    Full Text Available The mass and effective density of black carbon (BC particles generated from aqueous suspensions of Aquadag and fullerene soot was measured and parametrized as a function of their mobility diameter. The measurements were made by two independent research groups by operating a differential mobility analyser (DMA in series with an aerosol particle mass analyser (APM or a Couette centrifugal particle mass analyser (CPMA. Consistent and reproducible results were found in this study for different production lots of Aquadag, indicating that the effective density of these particles is a stable quantity and largely unaffected by differences in aerosol generation procedures and suspension treatments. The effective density of fullerene soot particles from one production lot was also found to be stable and independent of suspension treatments. Some difference to previous literature data was observed for both Aquadag and fullerene soot at larger particle diameters. Knowledge of the exact relationship between mobility diameter and particle mass is of great importance, as DMAs are commonly used to size-select particles from BC reference materials for calibration of single particle soot photometers (SP2, which quantitatively detect the BC mass in single particles.

  9. Effective density of Aquadag and fullerene soot black carbon reference materials used for SP2 calibration

    Directory of Open Access Journals (Sweden)

    M. Gysel

    2011-12-01

    Full Text Available The mass and effective density of black carbon (BC particles generated from aqueous suspensions of Aquadag and fullerene soot was measured and parametrized as a function of their mobility diameter. The measurements were made by two independent research groups by operating a differential mobility analyser (DMA in series with an aerosol particle mass analyser (APM or a Couette centrifugal particle mass analyser (CPMA. Consistent and reproducible results were found in this study for different production lots of Aquadag, indicating that the effective density of these particles is a stable quantity and largely unaffected by differences in aerosol generation procedures and suspension treatments. The effective density of fullerene soot particles from one production lot was also found to be stable and independent of suspension treatments. Some differences to previous literature data were observed for both Aquadag and fullerene soot at larger particle diameters. Knowledge of the exact relationship between mobility diameter and particle mass is of great importance, as DMAs are commonly used to size-select particles from BC reference materials for calibration of single particle soot photometers (SP2, which quantitatively detect the BC mass in single particles.

  10. Pt-Free Counter Electrodes with Carbon Black and 3D Network Epoxy Polymer Composites

    Science.gov (United States)

    Kang, Gyeongho; Choi, Jongmin; Park, Taiho

    2016-03-01

    Carbon black (CB) and a 3D network epoxy polymer composite, representing dual functions for conductive corrosion protective layer (CCPL) and catalytic layer (CL) by the control of CB weight ratio against polymer is developed. Our strategy provides a proper approach which applies high catalytic ability and chemical stability of CB in corrosive triiodide/iodide (I3-/I-) redox electrolyte system. The CB and a 3D network epoxy polymer composite coated on the stainless steel (SS) electrode to alternate counter electrodes in dye sensitized solar cells (DSSCs). A two-step spray pyrolysis process is used to apply a solution containing epoxy monomers and a polyfunctional amine hardener with 6 wt% CB to a SS substrate, which forms a CCPL. Subsequently, an 86 wt% CB is applied to form a CL. The excellent catalytic properties and corrosion protective properties of the CB and 3D network epoxy polymer composites produce efficient counter electrodes that can replace fluorine-doped tin oxide (FTO) with CCPL/SS and Pt/FTO with CL/CCPL/SS in DSSCs. This approach provides a promising approach to the development of efficient, stable, and cheap solar cells, paving the way for large-scale commercialization.

  11. Sorption and desorption of pentachlorophenol to black carbon of three different origins.

    Science.gov (United States)

    Luo, Ling; Lou, Liping; Cui, Xinyi; Wu, Binbin; Hou, Jiaai; Xun, Bei; Xu, Xinhua; Chen, Yingxu

    2011-01-30

    Rice straw charcoal, soot and fly ash (collectively termed "black carbon" or BC), which were found to widely exist in the environment and exhibit strong sorption of many organic compounds, were prepared for this study, and recorded as RC, SC, and FC, respectively. The characterization, sorption isotherm, and the effect of pH (from 3.0 to 9.0) on sorption capacity of each BC were investigated. It is demonstrated that RC possessed the largest surface area (234.9 m(2)/g), the highest porosity (0.4392 mL/g), and the largest amount of functional groups (2.995 mmol/g) of all. All the Freundlich, Langmuir and Dual-mode model can fit the sorption data of each BC well. The pH value could apparently affect the sorption capacity of pentachlorophenol (PCP) to BCs, which reached maximum value at pH 4.0. Furthermore, in order to validate the effect of pH on desorption capacity, we designed sorption-desorption cycle experiments at pH 9.0 and then pH 7.0, and found that the effect of pH on irreversible sorption and hysteresis effects were significant. As pH value decreasing from 9.0 to 7.0, the irreversible sorption capacities for RC, FC, and SC increased, and the desorption hysteresis index (H) values of PCP increased approximately 3 times for each BC.

  12. Seasonality of Black Carbon over the Great Lakes

    Science.gov (United States)

    Spak, S. N.; Holloway, T.

    2006-12-01

    We employ a 2001 annual simulation with the Community Multiscale Air Quality Model to identify patterns in the mass concentration and aerosol fraction of elemental carbon in the Upper Midwestern United States. CMAQ 4.3 is run at 36 km resolution using the 2001 EPA Clean Air Interstate Rule emissions inventory, MM5 meteorology, and boundary conditions from the MOZART global atmospheric chemistry model. Results are compared to daily-average surface observations from the IMPROVE and EPA Speciation Trends networks. Effects of CMAQ model configuration (plume-in-grid dispersion, advection scheme, sectional PM) are compared, identifying common findings and model-dependent features.

  13. Confronting the Global Climate Response to Black Carbon Aerosols with its Uncertainty

    Science.gov (United States)

    Mahajan, S.; Kovilakam, M.

    2015-12-01

    Black carbon aerosols (BC) modulate global temperatures and the hydrological cycle as well as regional climate. However, their radiative forcing is not well-constrained observationally and recent estimates of just the direct forcing ranges from 0.08 to 1.27 W/m2 - the upper limits of which puts BC second only to carbon dioxide in terms of radiative forcing. Consequently, the climate impacts of these heterogeneous short-lived forcing agents are highly uncertain. To establish the uncertainty in the climate response to BC, we conduct a suite of idealized experiments with the DOE/NCAR CESM1.0 model with the atmosphere component (CAM4) coupled to a Slab Ocean Model (SOM) forced separately with increasing BC concentrations covering a large swath of the estimated range of current BC radiative forcing. We find that the increase in BC results in global warming - with a sensitivity of 0.22 K/W/m2 including the semi-direct effects, decrease in global precipitation - despite the increase in global temperatures, a northwards shift of the ITCZ - along with an increase in cross-equatorial southwards energy transport, tropical expansion in the Northern Hemisphere - associated with BC induced mid-latitude warming, and an increase in precipitation during the Indian Monsoons - with the enhancement of the meridional tropospheric gradient, among other responses. Further, these global responses are near-linear functions of the increase in BC concentration, suggesting that the climate response to BC aerosols can be readily estimated if the uncertainty in BC can be constrained.

  14. Effect of vulcanization system and carbon black on mechanical and swelling properties of EPDM blends

    Directory of Open Access Journals (Sweden)

    Hesty Eka Mayasari

    2016-06-01

    Full Text Available EPDM (Ethylene propylene diene monomer is one of synthetic rubber that widely used in automotive. It must be vulcanized and added by other materials before used. The aim of this study is to investigate the effect of vulcanization system and the addition of carbon black (CB to the mechanical properties and swelling characteristic of EPDM. This research used three vulcanization system, conventional vulcanization (CV, efficient vulcanization (EV and semi-efficient vulcanization (SEV with the variation of carbon black 50, 60, 70 phr (per hundred resin. This research showed that EV system resulted faster vulcanization time and lower delta torque than SEV and CV systems. This system also performed the highest tensile strength, elongation, and tear strength, while SEV system resulted the highest hardness. Furthermore, the conventional vulcanization system resulted the lowest swelling index.

  15. NANOMECHANICAL MAPPING OF CARBON BLACK REINFORCED NATURAL RUBBER BY ATOMIC FORCE MICROSCOPY

    Institute of Scientific and Technical Information of China (English)

    Toshio Nishi; Hideyuki Nukaga; So Fujinami; Ken Nakajima

    2007-01-01

    Atomic force microscopy (AFM) has the advantage of obtaining mechanical properties as well as topographic information at the same time. By analyzing force-distance curves measured over two-dimensional area using Hertzian contact mechanics, Young's modulus mapping was obtained with nanometer-scale resolution. Furthermore, the sample deformation by the force exerted was also estimated from the force-distance curve analyses. We could thus reconstruct a real topographic image by incorporating apparent topographic image with deformation image. We applied this method to carbon black reinforced natural rubber to obtain Young's modulus distribution image together with reconstructed real topographic image.Then we were able to recognize three regions; rubber matrix, carbon black (or bound rubber) and intermediate regions.Though the existence of these regions had been investigated by pulsed nuclear magnetic resonance, this paper would be the first to report on the quantitative evaluation of the interfacial region in real space.

  16. Human lung epithelial cell A549 proteome data after treatment with titanium dioxide and carbon black.

    Science.gov (United States)

    Vuong, Ngoc Q; Goegan, Patrick; Mohottalage, Susantha; Breznan, Dalibor; Ariganello, Marianne; Williams, Andrew; Elisma, Fred; Karthikeyan, Subramanian; Vincent, Renaud; Kumarathasan, Premkumari

    2016-09-01

    Here, we have described the dataset relevant to the A549 cellular proteome changes after exposure to either titanium dioxide or carbon black particles as compared to the non-exposed controls, "Proteomic changes in human lung epithelial cells (A549) in response to carbon black and titanium dioxide exposures" (Vuong et al., 2016) [1]. Detailed methodologies on the separation of cellular proteins by 2D-GE and the subsequent mass spectrometry analyses using MALDI-TOF-TOF-MS are documented. Particle exposure-specific protein expression changes were measured via 2D-GE spot volume analysis. Protein identification was done by querying mass spectrometry data against SwissProt and RefSeq protein databases using Mascot search engine. Two-way ANOVA analysis data provided information on statistically significant A549 protein expression changes associated with particle exposures.

  17. Preparation of Waterborne Nanoscale Carbon Black Dispersion with Sodium Carboxymethyl Cellulose

    Institute of Scientific and Technical Information of China (English)

    YUAN Xia; FANG Kuan-jun

    2006-01-01

    Waterborne nanoscale carbon black dispersion (NCBD) was widely used in inkjet printing, spun-dyeing fibers and coloration fabrics. In this paper, NCBD was prepared using sodium carboxymethyl cellulose (CMC) as dispersant.Effects of CMC viscosity, ultrasonic time and oxidation with hydrogen peroxide on carbon black (CB) particle size were discussed. The results showed that CB particle size decreased by mechanical agitation while it increased by ultrasonic with the increase of CMC viscosity. Ultrasonic is a more effective method to disperse CB particles than that of mechanical agitation. CB particle size obviously decreased with increasing ultrasonic time and arrived at about 160 nm for 60 min. In addition, oxidation with 2 mol/L of H2O2 and 0.2 wt% of CMC300 reduced CB particle size to 160 nm at 90℃ for 2.5 h.

  18. Modulation of snow reflectance and snowmelt from Central Asian glaciers by anthropogenic black carbon

    Science.gov (United States)

    Schmale, Julia; Flanner, Mark; Kang, Shichang; Sprenger, Michael; Zhang, Qianggong; Guo, Junming; Li, Yang; Schwikowski, Margit; Farinotti, Daniel

    2017-01-01

    Deposited mineral dust and black carbon are known to reduce the albedo of snow and enhance melt. Here we estimate the contribution of anthropogenic black carbon (BC) to snowmelt in glacier accumulation zones of Central Asia based on in-situ measurements and modelling. Source apportionment suggests that more than 94% of the BC is emitted from mostly regional anthropogenic sources while the remaining contribution comes from natural biomass burning. Even though the annual deposition flux of mineral dust can be up to 20 times higher than that of BC, we find that anthropogenic BC causes the majority (60% on average) of snow darkening. This leads to summer snowmelt rate increases of up to 6.3% (7 cm a‑1) on glaciers in three different mountain environments in Kyrgyzstan, based on albedo reduction and snowmelt models.

  19. Implications of multiple scattering on the assessment of black carbon aerosol radiative forcing

    Science.gov (United States)

    Nair, Vijayakumar S.; Suresh Babu, S.; Krishna Moorthy, K.; Satheesh, S. K.

    2014-11-01

    The effects of radiative coupling between scattering and absorbing aerosols, in an external mixture, on the aerosol radiative forcing (ARF) due to black carbon (BC), its sensitivity to the composite aerosol loading and composition, and surface reflectance are investigated using radiative transfer model simulations. The ARF due to BC is found to depend significantly on the optical properties of the ‘neighboring’ (non-BC) aerosol species. The scattering due to these species significantly increases the top of the atmospheric warming due to black carbon aerosols, and significant changes in the radiative forcing efficiency of BC. This is especially significant over dark surfaces (such as oceans), despite the ARF due to BC being higher over snow and land-surfaces. The spatial heterogeneity of this effect (coupling or multiple scattering by neighboring aerosol species) imposes large uncertainty in the estimation ARF due to BC aerosols, especially over the oceans.

  20. Human lung epithelial cell A549 proteome data after treatment with titanium dioxide and carbon black

    Directory of Open Access Journals (Sweden)

    Ngoc Q. Vuong

    2016-09-01

    Full Text Available Here, we have described the dataset relevant to the A549 cellular proteome changes after exposure to either titanium dioxide or carbon black particles as compared to the non-exposed controls, “Proteomic changes in human lung epithelial cells (A549 in response to carbon black and titanium dioxide exposures” (Vuong et al., 2016 [1]. Detailed methodologies on the separation of cellular proteins by 2D-GE and the subsequent mass spectrometry analyses using MALDI-TOF-TOF-MS are documented. Particle exposure-specific protein expression changes were measured via 2D-GE spot volume analysis. Protein identification was done by querying mass spectrometry data against SwissProt and RefSeq protein databases using Mascot search engine. Two-way ANOVA analysis data provided information on statistically significant A549 protein expression changes associated with particle exposures.

  1. Current Situation and Prospect of White Carbon Black Industry in China

    Institute of Scientific and Technical Information of China (English)

    Zhu Chunyu

    2011-01-01

    1.Analysis of Market Operation in 2010 Year 2010 is the ending year of the "11th Five-Year Plan".Under the effect of a series of central government policies including coping with the international financial crisis,accelerating the transformation of economic development pattern and economic restructuring,and promoting steady and rapid development of economy,the situation is basically established that industrial economy operation changes from turnaround to steady growth,and industrial economy develops steadily and rapidly.This can be shown in the white carbon black industry,through the whole year,white carbon black industry maintains steady and rapid development,and the output of which has grown greatly compared with last year.

  2. Distribution of black carbon in Ponderosa pine litter and soils following the High Park wildfire

    Science.gov (United States)

    Boot, C. M.; Haddix, M.; Paustian, K.; Cotrufo, M. F.

    2014-12-01

    Black carbon (BC), the heterogeneous product of burned biomass, is a critical component in the global carbon cycle, yet timescales and mechanisms for incorporation into the soil profile are not well understood. The High Park Fire, which took place in northwestern Colorado in the summer of 2012, provided an opportunity to study the effects of both fire intenstiy and geomorphology on properties of carbon (C), nitrogen (N), and BC in the Cache La Poudre River drainage. We sampled montane Ponderosa pine litter, 0-5 cm soils, and 5-15 cm soils four months post-fire in order to examine the effects of slope and burn intensity on %C, C stocks, %N and black carbon (g kg-1 C, and g m-2). We developed and implemented the benzene polycarboxylic acid (BPCA) method for quantifying BC. With regard to slope, we found that steeper slopes had higher C : N than shallow slopes, but that there was no difference in black carbon content or stocks. BC content was greatest in the litter in burned sites (19 g kg-1 C), while BC stocks were greatest in the 5-15 cm subsurface soils (23 g m-2). At the time of sampling, none of the BC deposited on the land surface post-fire had been incorporated into to either the 0-5 cm or 5-15 cm soil layers. The ratio of B5CA : B6CA (less condensed to more condensed BC) indicated there was significantly more older, more processed BC at depth. Total BC soil stocks were relatively low compared to other fire-prone grassland and boreal forest systems, indicating most of the BC produced in this system is likely transported off the surface through erosion events. Future work examining mechanisms for BC transport will be required for understanding the role BC plays in the global carbon cycle.

  3. Distribution of black carbon in Ponderosa pine litter and soils following the High Park wildfire

    Directory of Open Access Journals (Sweden)

    C. M. Boot

    2014-12-01

    Full Text Available Black carbon (BC, the heterogeneous product of burned biomass, is a critical component in the global carbon cycle, yet timescales and mechanisms for incorporation into the soil profile are not well understood. The High Park Fire, which took place in northwestern Colorado in the summer of 2012, provided an opportunity to study the effects of both fire intenstiy and geomorphology on properties of carbon (C, nitrogen (N, and BC in the Cache La Poudre River drainage. We sampled montane Ponderosa pine litter, 0–5 cm soils, and 5–15 cm soils four months post-fire in order to examine the effects of slope and burn intensity on %C, C stocks, %N and black carbon (g kg−1 C, and g m−2. We developed and implemented the benzene polycarboxylic acid (BPCA method for quantifying BC. With regard to slope, we found that steeper slopes had higher C : N than shallow slopes, but that there was no difference in black carbon content or stocks. BC content was greatest in the litter in burned sites (19 g kg−1 C, while BC stocks were greatest in the 5–15 cm subsurface soils (23 g m−2. At the time of sampling, none of the BC deposited on the land surface post-fire had been incorporated into to either the 0–5 cm or 5–15 cm soil layers. The ratio of B5CA : B6CA (less condensed to more condensed BC indicated there was significantly more older, more processed BC at depth. Total BC soil stocks were relatively low compared to other fire-prone grassland and boreal forest systems, indicating most of the BC produced in this system is likely transported off the surface through erosion events. Future work examining mechanisms for BC transport will be required for understanding the role BC plays in the global carbon cycle.

  4. Comparison of structural health assessment capabilities in epoxy – carbon black and epoxy – carbon nanotube nanocomposites

    Directory of Open Access Journals (Sweden)

    F. Inam

    2014-01-01

    Full Text Available A novel method for comparing structural health of different types of brittle epoxy nanocomposites filled with carbon nanostructured fillers is presented. Epoxy – 0.2 vol% carbon black (CB and epoxy – 0.2 vol% carbon nanotube (CNT nanocomposite bars were prepared by calendering and thermal curing. Nanocomposite bars were subjected to Vickers diamond indentation to produce sub-surface damage. Electrical conductivities were analysed by 4-point method to estimate the structural damage caused by indentation. For comprehensive comparison, fracture toughness and percolation threshold were analysed as well. Because of the systematically induced indentation damage, a sharp decrease of 89% was observed in the electrical conductivity of epoxy – CNT nanocomposite as compared to 25% in the electrical conductivity of epoxy – CB nanocomposite. CNTs impart superior damage sensing capability in brittle nanocomposite structures, in comparison to CB, due to their high aspect ratio (fibrous nature and high electrical conductivity.

  5. Black carbon mixing state impacts on cloud microphysical properties: effects of aerosol plume and environmental conditions

    Energy Technology Data Exchange (ETDEWEB)

    Ching, Ping Pui; Riemer, Nicole; West, Matthew

    2016-05-27

    Black carbon (BC) is usually mixed with other aerosol species within individual aerosol particles. This mixture, along with the particles' size and morphology, determines the particles' optical and cloud condensation nuclei properties, and hence black carbon's climate impacts. In this study the particle-resolved aerosol model PartMC-MOSAIC was used to quantify the importance of black carbon mixing state for predicting cloud microphysical quantities. Based on a set of about 100 cloud parcel simulations a process level analysis framework was developed to attribute the response in cloud microphysical properties to changes in the underlying aerosol population ("plume effect") and the cloud parcel cooling rate ("parcel effect"). It shows that the response of cloud droplet number concentration to changes in BC emissions depends on the BC mixing state. When the aerosol population contains mainly aged BC particles an increase in BC emission results in increasing cloud droplet number concentrations ("additive effect"). In contrast, when the aerosol population contains mainly fresh BC particles they act as sinks for condensable gaseous species, resulting in a decrease in cloud droplet number concentration as BC emissions are increased ("competition effect"). Additionally, we quantified the error in cloud microphysical quantities when neglecting the information on BC mixing state, which is often done in aerosol models. The errors ranged from -12% to +45% for the cloud droplet number fraction, from 0% to +1022% for the nucleation-scavenged black carbon (BC) mass fraction, from -12% to +4% for the effective radius, and from -30% to +60% for the relative dispersion.

  6. Climate effects of black carbon and the emission reduction for mitigating climate change /

    OpenAIRE

    Xu, Yangyang

    2014-01-01

    Black carbon (BC) aerosols are significant contributors to anthropogenic climate change and are considered as the second largest warming agent only after CO₂. To better quantify the present-day Asian BC aerosol forcing, in Chapter 2 we utilize both a top-down approach using ground -based and satellite observations, as well as a bottom-up approach using a latest global climate model. By comparing the observations with the model simulations, we show that the emission inventory over Asia used in...

  7. Adsorption Behavior of Black Carbon for Radioactive Iodine Species in Subsurface Environments

    Science.gov (United States)

    Choung, S.; Kim, M.; Um, W.

    2012-12-01

    Releases of radioactive iodines (125/129/131I) into subsurface environments occur during nuclear power plant operations, nuclear weapons tests, and nuclear accidents such as Chernobyl and Fukushima. Environmental concern is mostly for 129I due to high toxicity and long-half life, t1/2=1,600,000 years. The fate and transport of radioactive iodines depend on the speciation in the environments. Sorption of iodate (IO3-) is strongly affected by natural organic matter (NOM) in soil/sediments, while iodide (I-) sorption is less. Although there are numerous forms and compositions of NOM in soil/sediments, previous studies were mostly focused on general organic matter such as humic and fulvic acids. The objective of this study is addressed to evaluate the impact of black carbon as different NOM forms in subsurface environments. Laboratory-produced wood char was used as a representative of black carbon for sorption batch experiments. Commercial humic acid was added to experiments for comparison of iodine sorption behavior to black carbon material. Stable iodine isotope, 127I, was used as a surrogate of radioactive iodine. The 13C-NMR analyses indicated that the wood char consisted of dominantly aromatic chemical structures, while the humic acid exhibited relatively more aliphatic structures than aromaticity. The char and humic acid significantly increased iodide and iodate sorption, respectively. However, iodate sorption on char and iodide sorption on humic acid were negligible in this study. These observations implied different sorption mechanisms between black carbon and humic acid due to different pore structures and chemical compositions. Both of sorption isotherms are dependent on aqueous concentrations, following Freundlich isotherm with n~0.7. The sorption behavior and mechanism of iodine is significantly influenced by the NOM types in soils and sediments, which can enhance iodine retardation in the subsurface environment.

  8. Functional Carbon Materials for Electrochemical Energy Storage

    Science.gov (United States)

    Zhou, Huihui

    The ability to harvest and convert solar energy has been associated with the evolution of human civilization. The increasing consumption of fossil fuels since the industrial revolution, however, has brought to concerns in ecological deterioration and depletion of the fossil fuels. Facing these challenges, humankind is forced to seek for clean, sustainable and renewable energy resources, such as biofuels, hydraulic power, wind power, geothermal energy and other kinds of alternative energies. However, most alternative energy sources, generally in the form of electrical energy, could not be made available on a continuous basis. It is, therefore, essential to store such energy into chemical energy, which are portable and various applications. In this context, electrochemical energy-storage devices hold great promises towards this goal. The most common electrochemical energy-storage devices are electrochemical capacitors (ECs, also called supercapacitors) and batteries. In comparison to batteries, ECs posses high power density, high efficiency, long cycling life and low cost. ECs commonly utilize carbon as both (symmetric) or one of the electrodes (asymmetric), of which their performance is generally limited by the capacitance of the carbon electrodes. Therefore, developing better carbon materials with high energy density has been emerging as one the most essential challenges in the field. The primary objective of this dissertation is to design and synthesize functional carbon materials with high energy density at both aqueous and organic electrolyte systems. The energy density (E) of ECs are governed by E = CV 2/2, where C is the total capacitance and V is the voltage of the devices. Carbon electrodes with high capacitance and high working voltage should lead to high energy density. In the first part of this thesis, a new class of nanoporous carbons were synthesized for symmetric supercapacitors using aqueous Li2SO4 as the electrolyte. A unique precursor was adopted to

  9. Modelling black spruce primary production and carbon allocation in the Quebec boreal forest

    Science.gov (United States)

    Gennaretti, Fabio; Guiot, Joel; Berninger, Frank; Boucher, Etienne; Gea-Izquierdo, Guillermo

    2017-04-01

    Boreal ecosystems are crucial carbon stores that must be urgently quantified and preserved. Their future evolution is extremely important for the global carbon budget. Here, we will show the progresses achieved with the MAIDEN forest ecophysiological model in simulating carbon fluxes of black spruce (Picea mariana (Mill.) B.S.P.) forests, the most representative ecosystem of the North American boreal biome. Starting from daily minimum-maximum air temperature, precipitation and CO2 atmospheric concentration, MAIDEN models the phenological (5 phenological phases are simulated each year) and meteorological controls on gross primary production (GPP) and carbon allocation to stem. The model is being calibrated on eddy covariance and tree-ring data. We will discuss the model's performance and the modifications introduced in MAIDEN to adapt the model to temperature sensitive forests of the boreal region.

  10. Role of Black Carbon and Absorbing Organic Carbon Aerosols in Surface Dimming Trends

    Science.gov (United States)

    Feng, Y.; Ramanathan, V.; Kotamarthi, V. R.

    2010-12-01

    Solar radiation reaching at the Earth’s surface plays an essential role in driving both atmosphere hydrological and land/ocean biogeochemical processes. Measurements have shown significant decreases in surface solar radiation (dimming) in many regions since 1960s. At least half of the observed dimming could be linked to the direct radiative effect of anthropogenic aerosols, especially absorbing aerosols like black carbon (BC) due to their strong atmospheric absorption. However, previous model-data comparisons indicate that absorption by aerosols is commonly and significantly underestimated in current GCM simulations by several factors over regions. Using a global chemical transport model coupled with a radiative transfer model, we include a treatment for absorbing organic carbons (OC) from bio-fuel and open biomass burnings in optical calculations and estimate aerosol radiative forcings for two anthropogenic aerosol emission scenarios representative of 1975 and 2000. Assumptions about aerosol mixing and the OC absorption spectrum are examined by comparing simulated atmospheric heating against aircraft optical and radiation measurements. The calculated aerosol single scattering albedo distribution (0.93+/-0.044) is generally comparable to the AERONET data (0.93+/-0.030) for year 2001, with best agreements in Europe and N. America, while overestimated in E. Asia and underestimated in the S. American biomass burning areas. On a global scale, inclusion of absorbing OC enhances the absorption in the atmosphere by 11% for July. The estimated aerosol direct radiative forcing at TOA (-0.24 W/m2) is similar to the average value of the AeroCom models based on the same 2000 emissions, but significantly enhanced negatively at surface by about 53% (-1.56 W/m2) and the atmosphere absorption is increased by +61% (+1.32 W/m2). About 87% of the estimated atmosphere absorption and 42% of the surface dimming is contributed by BC. Between 1975 and 2000, the calculated all-sky flux

  11. Online single particle measurements of black carbon coatings, structure and optical properties

    Science.gov (United States)

    Allan, James; Liu, Dantong; Taylor, Jonathan; Flynn, Michael; Williams, Paul; Morgan, William; Whitehead, James; Alfarra, Rami; McFiggans, Gordon; Coe, Hugh

    2016-04-01

    The impacts of black carbon on meteorology and climate remain a major source of uncertainty, owing in part to the complex relationship between the bulk composition of the particulates and their optical properties. A particular complication stems from how light interacts with particles in response to the microphysical configuration and any 'coatings', i.e. non-black carbon material that is either co-emitted or subsequently obtained through atmospheric processing. This may cause the particle to more efficiently absorb or scatter light and may even change the sign of its radiative forcing potential. While much insight has been gained through measurements of bulk aerosol properties, either while suspended or after collection on a filter or impactor substrate, this does not provide a complete picture and thus may not adequately constrain the system. Here we present an overview of recent work to better constrain the properties of black carbon using online, in situ measurements of single particles, primarily using a Single Particle Soot Photometer (SP2). We have developed novel methods of inverting the data produced and combining the different metrics derived so as to give the most effective insights into black carbon sources, processes and properties. We have also used this measurement in conjunction with other instruments (sometimes in series) and used the data to challenge many commonly used models of optical properties such as core-shell Mie, Rayleigh-Debeye-Gans and effective medium. This work has been carried out in a variety of atmospheric environments and with laboratory-produced soots, e.g. from a diesel engine rig. Highlights include the finding that with real-world atmospheric aerosols, bulk optical measurements may be insufficient to derive brown carbon parameters without detailed morphological data. We also show that the enhancement of absorption for both ambient and laboratory generated particles only occurs after the coating mass fraction reaches a certain

  12. Physical activity, black carbon exposure, and DNA methylation in the FOXP3 promoter.

    Science.gov (United States)

    Lovinsky-Desir, Stephanie; Jung, Kyung Hwa; Jezioro, Jacqueline R; Torrone, David Z; de Planell-Saguer, Mariangels; Yan, Beizhan; Perera, Frederica P; Rundle, Andrew G; Perzanowski, Matthew S; Chillrud, Steven N; Miller, Rachel L

    2017-01-01

    Physical activity is associated with improvement in lung function; however, pollution exposure during physical activity can lead to a transient reduction in lung function. This paradoxical relationship may be linked to altered T regulatory (Treg) cell activity, which increases with exercise and suppresses airway inflammation, but decreases in association with exposure to air pollution. To clarify these relationships, we investigated buccal cell DNA methylation of the forkhead box p3 (FOXP3) gene promoter, a proposed biomarker of Treg activity. We hypothesized that active urban children would have lower FOXP3 promoter methylation, associated with better lung function compared to non-active children. We also hypothesized that this relationship would be attenuated by high exposure to the air pollutant black carbon (BC). We performed a cross-sectional study of 135 children ages 9-14 who live in New York City. Activity was measured across 6 days. BC exposure was assessed by personal monitors worn for two 24-h periods, followed by lung function assessment. Buccal swabs were collected for DNA methylation analysis of three regions (six CpG sites) in the FOXP3 promoter. In multivariable regression models, overall, there was no significant relationship between physical activity and FOXP3 promoter methylation (p > 0.05). However, in stratified analyses, among children with higher BC exposure (≥1200 ng/m(3)), physical activity was associated with 2.37% lower methylation in promoter 2 (CpGs -77, -65, and -58) (βestimate = -2.37%, p  0.05). Differences across strata were statistically significant (pinteraction = 0.04). Among all children, after controlling for BC concentration, promoter 2 methylation was associated with reduced FEV1/FVC (βestimate = -0.40%, p promoter methylation, a possible indicator of greater Treg function, under conditions of high BC exposure. Reduced FOXP3 promoter methylation was associated with higher lung function. These

  13. Carbohydrate functionalized carbon nanotubes and their applications.

    Science.gov (United States)

    Gorityala, Bala Kishan; Ma, Jimei; Wang, Xin; Chen, Peng; Liu, Xue-Wei

    2010-08-01

    Carbon nanotubes (CNTs) have attracted tremendous attention in biomedical applications due to their molecular size and unique properties. This tutorial review summarizes the strategies to functionalize CNTs with bioactive carbohydrates, which improve their solubility, biocompatibility and biofunctionalities while preserving their desired properties. In addition, studies on the usage of carbohydrate functionalized CNTs to detect bacteria, to bind to specific lectins, to deliver glycomimetic drug molecules into cells and to probe cellular activities as biosensors are reviewed. Improvement in biocompatibility and introduction of bio-functionalities by integration of carbohydrate with CNTs are paving the way to glyconanotechnology and may provide new tools for glycobiological studies.

  14. Effects of Nanoscale Carbon Black Modified by HNO3 on Immobilization and Phytoavailability of Ni in Contaminated Soil

    Directory of Open Access Journals (Sweden)

    Jiemin Cheng

    2015-01-01

    Full Text Available A surface-modified nanoscale carbon black (MCB as Ni adsorbent in contaminated soil was prepared by oxidizing the carbon black with 65% HNO3. The surface properties of the adsorbent were characterized by zeta potential analysis, scanning electron microscopy (SEM, and Fourier transform infrared spectroscopy (FTIRs. Batch experiments were conducted to evaluate the improvement of Ni2+ adsorption by MCB. Greenhouse cultivation experiments were conducted to examine the effect of MCB on the DTPA-extractable Ni2+ in soil, Ni2+ uptake of ryegrass shoot, and growth of ryegrass. Results indicated that MCB had much lower negative zeta potential, more functional groups for exchange and complexation of cation, and more heterogeneous pores and cavities for the adsorption of cation than the unmodified parent one (CB. MCB showed enhanced sorption capacity for Ni (qmax, 49.02 mg·g−1 compared with CB (qmax, 39.22 mg·g−1. Greenhouse cultivation experiment results showed that the biomass of ryegrass shoot and the Ni uptake of the ryegrass shoot were significantly increased and the concentrations of DTPA-extractable Ni in soil were significantly decreased with the increasing of MCB amount. It is clear from this work that the MCB had good adsorption properties for the Ni and could be applied in the in situ immobilization and remediation of heavy metal contaminated saline-alkali soils.

  15. Functionalization of vertically aligned carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Eloise Van Hooijdonk

    2013-02-01

    Full Text Available This review focuses and summarizes recent studies on the functionalization of carbon nanotubes oriented perpendicularly to their substrate, so-called vertically aligned carbon nanotubes (VA-CNTs. The intrinsic properties of individual nanotubes make the VA-CNTs ideal candidates for integration in a wide range of devices, and many potential applications have been envisaged. These applications can benefit from the unidirectional alignment of the nanotubes, the large surface area, the high carbon purity, the outstanding electrical conductivity, and the uniformly long length. However, practical uses of VA-CNTs are limited by their surface characteristics, which must be often modified in order to meet the specificity of each particular application. The proposed approaches are based on the chemical modifications of the surface by functionalization (grafting of functional chemical groups, decoration with metal particles or wrapping of polymers to bring new properties or to improve the interactions between the VA-CNTs and their environment while maintaining the alignment of CNTs.

  16. Black Carbon in Estuarine (Coastal) High-molecular-weight Dissolved Organic Matter

    Science.gov (United States)

    Mannino, Antonio; Harvey, H. Rodger

    2003-01-01

    Dissolved organic matter (DOM) in the ocean constitutes one of the largest pools of organic carbon in the biosphere, yet much of its composition is uncharacterized. Observations of black carbon (BC) particles (by-products of fossil fuel combustion and biomass burning) in the atmosphere, ice, rivers, soils and marine sediments suggest that this material is ubiquitous, yet the contribution of BC to the ocean s DOM pool remains unknown. Analysis of high-molecular-weight DOM isolated from surface waters of two estuaries in the northwest Atlantic Ocean finds that BC is a significant component of DOM, suggesting that river-estuary systems are important exporters of BC to the ocean through DOM. We show that BC comprises 4-7% of the dissolved organic carbon (DOC) at coastal ocean sites, which supports the hypothesis that the DOC pool is the intermediate reservoir in which BC ages prior to sedimentary deposition. Flux calculations suggest that BC could be as important as vascular plant-derived lignin in terms of carbon inputs to the ocean. Production of BC sequesters fossil fuel- and biomass-derived carbon into a refractory carbon pool. Hence, BC may represent a significant sink for carbon to the ocean.

  17. Assessment of carbon nanoparticle exposure on murine macrophage function

    Science.gov (United States)

    Suro-Maldonado, Raquel M.

    There is growing concern about the potential cytotoxicity of nanoparticles. Exposure to respirable ultrafine particles (2.5uM) can adversely affect human health and have been implicated with episodes of increased respiratory diseases such as asthma and allergies. Nanoparticles are of particular interest because of their ability to penetrate into the lung and potentially elicit health effects triggering immune responses. Nanoparticles are structures and devises with length scales in the 1 to 100-nanometer range. Black carbon (BC) nanoparticles have been observed to be products of combustion, especially flame combustion and multi-walled carbon nanotubes (MWCNT) have been shown to be found in both indoor and outdoor air. Furthermore, asbestos, which have been known to cause mesothelioma as well as lung cancer, have been shown to be structurally identical to MWCNTs. The aims of these studies were to examine the effects of carbon nanoparticles on murine macrophage function and clearance mechanisms. Macrophages are immune cells that function as the first line of defense against invading pathogens and are likely to be amongst the first cells affected by nanoparticles. Our research focused on two manufactured nanoparticles, MWCNT and BC. The two were tested against murine-derived macrophages in a chronic contact model. We hypothesized that long-term chronic exposure to carbon nanoparticles would decrease macrophages ability to effectively respond to immunological challenge. Production of nitric oxide (NO), tumor necrosis factor alpha (TNF-alpha), cell surface macrophage; activation markers, reactive oxygen species formation (ROS), and antigen processing and presentation were examined in response to lipopolysaccharide (LPS) following a 144hr exposure to the particulates. Data demonstrated an increase in TNF-alpha, and NO production; a decrease in phagocytosis and antigen processing and presentation; and a decrease in the expression levels of cell surface macrophage

  18. Quantification of Black Carbon and Other Pollutant Emissions from a Traditional and an Improved Cookstove

    Energy Technology Data Exchange (ETDEWEB)

    Kirchstetter, Thomas [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Preble, Chelsea [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Hadley, Odelle [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Gadgil, Ashok [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2010-11-05

    Traditional methods of cooking in developing regions of the world emit pollutants that endanger the lives of billions of people and contribute to climate change. This study quantifies the emission of pollutants from the Berkeley-Darfur Stove and the traditional three-stone fire at the Lawrence Berkeley National Laboratory cookstove testing facility. The Berkeley-Darfur Stove was designed as a fuel efficient alternative to the three-stone fire to aid refugees in Darfur, who walk long distances from their camps and risk bodily harm in search of wood for cooking. A potential co-benefit of the more fuel efficient stove may be reduced pollutant emissions. This study measured emissions of carbon dioxide, carbon monoxide, particulate matter, and sunlight-absorbing black carbon. It also measured climate-relevant optical properties of the emitted particulate matter. Pollutant monitors were calibrated specifically for measuring cookstove smoke.

  19. [Environmental behavior and effect of biomass-derived black carbon in soil: a review].

    Science.gov (United States)

    Liu, Yu-Xue; Liu, Wei; Wu, Wei-Xiang; Zhong, Zhe-Ke; Chen, Ying-Xu

    2009-04-01

    Biomass-derived black carbon, also named biochar, has the characteristics of high stability against decay and high capability of adsorption, and can affect the environment through its interactions with climate and geology, playing a significant role in global climate change, carbon biogeochemical cycle, and environmental system. In recent years, more and more researchers in the fields of atmospheric sciences, geology, and environmental science focused on the environmental behavior and effect of biochar. As one possible source of the components with high aromatic structure in soil humus, biochar is of great importance in increasing soil carbon storage and improving soil fertility, and in maintaining the balance of soil ecosystem. This paper offered the latest information regarding the characteristics and biotic and abiotic oxidation mechanisms of biochar, its effects on global climate change, and the environmental effect of biochar in soil. Research prospects were briefly discussed on the environmental behavior and effect of biochar in soil ecosystem.

  20. Daily black carbon emissions from fires in northern Eurasia for 2002-2015

    Science.gov (United States)

    Hao, Wei Min; Petkov, Alexander; Nordgren, Bryce L.; Corley, Rachel E.; Silverstein, Robin P.; Urbanski, Shawn P.; Evangeliou, Nikolaos; Balkanski, Yves; Kinder, Bradley L.

    2016-12-01

    Black carbon (BC) emitted from fires in northern Eurasia is transported and deposited on ice and snow in the Arctic and can accelerate its melting during certain times of the year. Thus, we developed a high spatial resolution (500 m × 500 m) dataset to examine daily BC emissions from fires in this region for 2002-2015. Black carbon emissions were estimated based on MODIS (Moderate Resolution Imaging Spectroradiometer) land cover maps and detected burned areas, the Forest Inventory Survey of the Russian Federation, the International Panel on Climate Change (IPCC) Tier-1 Global Biomass Carbon Map for the year 2000, and vegetation specific BC emission factors. Annual BC emissions from northern Eurasian fires varied greatly, ranging from 0.39 Tg in 2010 to 1.82 Tg in 2015, with an average of 0.71 ± 0.37 Tg from 2002 to 2015. During the 14-year period, BC emissions from forest fires accounted for about two-thirds of the emissions, followed by grassland fires (18 %). Russia dominated the BC emissions from forest fires (92 %) and central and western Asia was the major region for BC emissions from grassland fires (54 %). Overall, Russia contributed 80 % of the total BC emissions from fires in northern Eurasia. Black carbon emissions were the highest in the years 2003, 2008, and 2012. Approximately 58 % of the BC emissions from fires occurred in spring, 31 % in summer, and 10 % in fall. The high emissions in spring also coincide with the most intense period of ice and snow melting in the Arctic.

  1. Mass Functions of the Active Black Holes in Distant Quasars from the Sloan Digital Sky Survey Data Release 3

    DEFF Research Database (Denmark)

    Vestergaard, Marianne; Fan, X.; Tremonti, C. A.

    2007-01-01

    We present the mass functions of actively accreting supermassive black holes over the redshift range 0.3......We present the mass functions of actively accreting supermassive black holes over the redshift range 0.3...

  2. Evaluation of a protocol for the quantification of black carbon in sediments

    Science.gov (United States)

    Gustafsson, Örjan; Bucheli, Thomas D.; Kukulska, Zofia; Andersson, Mette; Largeau, Claude; Rouzaud, Jean-NoëL.; Reddy, Christopher M.; Eglinton, Timothy I.

    2001-12-01

    Formation of highly condensed black carbon (BC) from vegetation fires and wood fuel combustion presumably transfers otherwise rapidly cycling carbon from the atmosphere-biosphere cycle into a much slower cycling geological form. Recently reported BC fractions of total organic carbon (TOC) in surficial marine sediments span a wide range (2-90%), leaving it presently unclear whether this variation reflects natural processes or is largely due to method differences. In order to elucidate the importance of BC to carbon burial the specificity of applied methods needs to be constrained. Here the operating range and applicability of a commonly used chemothermal oxidation (CTO) method is evaluated using putative BC standards, potentially interfering substances, and natural matrix standards. Test results confirm the applicability of the method to marine sediments. Integrity tests with model substrates suggest applicability to low-carbon soils but only with a lower specificity to seawater particulate matter. The BC content of marine sediment samples in a set of studies employing the CTO method proved to be consistent with associated geochemical information. The radiocarbon content of the BC isolate in an environmental matrix standard was shown to be similar to the radiocarbon signature of pyrogenic polycyclic aromatic hydrocarbons (PAHs), here serving as molecular markers of combustion (fraction modern fM of BC was 0.065 ± 0.014 and of PAHs 0.056 ± 0.020), while being clearly distinct from the radiocarbon content of the bulk TOC (fM = 0.61 ± 0.08). Urgent questions such as the global accumulation rate of black carbon in soils and sediments may prove approachable with the chemothermal oxidation technique of BC quantification.

  3. Studies on Glass Reinforced Epoxy Resin Using Vulkadur- A as Crosslinking Agent both in Presence and Absence of Carbon Black and other Non black Fillers

    Directory of Open Access Journals (Sweden)

    T. K. Ghosh

    1974-04-01

    Full Text Available Epoxy resin can be reinforced with glass (fabric form in presence of Vulkadur-A, a phenol formaldehyde resin containing a hardening agent. Overall enhancement in mechanical properties has been found stocks cured with Vulkadur-A containing 2.5 parts of carbon black as filler.

  4. Environmental Technology Verification Program Advanced Monitoring Systems Center Quality Assurance Project Plan for Verification of Black Carbon Monitors

    Science.gov (United States)

    Black carbon is a term that is commonly used to describe strongly light absorbing carbon (LAC), which is thought to play a significant role in global climate change through direct absorption of light, interaction with clouds, and by reducing the reflectivity of snow and ice. BC ...

  5. Estimating particulate black carbon concentrations using two offline light absorption methods applied to four types of filter media

    Science.gov (United States)

    Davy, Pamela M.; Tremper, Anja H.; Nicolosi, Eleonora M. G.; Quincey, Paul; Fuller, Gary W.

    2017-03-01

    Atmospheric particulate black carbon has been linked to adverse health outcomes. Additional black carbon measurements would aid a better understanding of population exposure in epidemiological studies as well as the success, or otherwise, of relevant abatement technologies and policies. Two light absorption measurement methods of particles collected on filters have been applied to four different types of filters to provide estimations of particulate black carbon concentrations. The ratio of transmittance (lnI0/I) to reflectance (lnR0/R) varied by filter type and ranged from close to 0.5 (as expected from simple theory) to 1.35 between the four filter types tested. The relationship between light absorption and black carbon, measured by the thermal EC(TOT) method, was nonlinear and differed between filter type and measurement method. This is particularly relevant to epidemiological studies that use light absorption as an exposure metric. An extensive archive of filters was used to derive loading factors and mass extinction coefficients for each filter type. Particulate black carbon time series were then calculated at locations where such measurements were not previously available. When applied to two roads in London, black carbon concentrations were found to have increased between 2011 and 2013, by 0.3 (CI: -0.1, 0.5) and 0.4 (CI: 0.1, 0.9) μg m-3 year-1, in contrast to the expectation from exhaust abatement policies. New opportunities using archived or bespoke filter collections for studies on the health effects of black carbon and the efficacy of abatement strategies are created.

  6. Functionally Graded Nanophase Beryllium/Carbon Composites

    Science.gov (United States)

    Choi, Michael K.

    2003-01-01

    Beryllium, beryllium alloys, beryllium carbide, and carbon are the ingredients of a class of nanophase Be/Be2C/C composite materials that can be formulated and functionally graded to suit a variety of applications. In a typical case, such a composite consists of a first layer of either pure beryllium or a beryllium alloy, a second layer of B2C, and a third layer of nanophase sintered carbon derived from fullerenes and nanotubes. The three layers are interconnected through interpenetrating spongelike structures. These Be/Be2C/C composite materials are similar to Co/WC/diamond functionally graded composite materials, except that (1) W and Co are replaced by Be and alloys thereof and (2) diamond is replaced by sintered carbon derived from fullerenes and nanotubes. (Optionally, one could form a Be/Be2C/diamond composite.) Because Be is lighter than W and Co, the present Be/Be2C/C composites weigh less than do the corresponding Co/WC/diamond composites. The nanophase carbon is almost as hard as diamond. WC/Co is the toughest material. It is widely used for drilling, digging, and machining. However, the fact that W is a heavy element (that is, has high atomic mass and mass density) makes W unattractive for applications in which weight is a severe disadvantage. Be is the lightest tough element, but its toughness is less than that of WC/Co alloy. Be strengthened by nanophase carbon is much tougher than pure or alloy Be. The nanophase carbon has an unsurpassed strength-to-weight ratio. The Be/Be2C/C composite materials are especially attractive for terrestrial and aerospace applications in which there are requirements for light weight along with the high strength and toughness of the denser Co/WC/diamond materials. These materials could be incorporated into diverse components, including cutting tools, bearings, rocket nozzles, and shields. Moreover, because Be and C are effective as neutron moderators, Be/Be2C/C composites could be attractive for some nuclear applications.

  7. Black carbon particulate matter emission factors for buoyancy-driven associated gas flares.

    Science.gov (United States)

    McEwen, James D N; Johnson, Matthew R

    2012-03-01

    Flaring is a technique used extensively in the oil and gas industry to burn unwanted flammable gases. Oxidation of the gas can preclude emissions of methane (a potent greenhouse gas); however, flaring creates other pollutant emissions such as particulate matter (PM) in the form of soot or black carbon (BC). Currently available PM emissionfactors for flares were reviewed and found to be questionably accurate, or based on measurements not directly relevant to open-atmosphere flares. In addition, most previous studies of soot emissions from turbulent diffusion flames considered alkene or alkyne based gaseous fuels, and few considered mixed fuels in detail and/or lower sooting propensity fuels such as methane, which is the predominant constituent of gas flared in the upstream oil and gas industry. Quantitative emission measurements were performed on laboratory-scale flares for a range of burner diameters, exit velocities, and fuel compositions. Drawing from established standards, a sampling protocol was developed that employed both gravimetric analysis of filter samples and real-time measurements of soot volume fraction using a laser-induced incandescence (LII) system. For the full range of conditions tested (burner inner diameter [ID] of 12.7-76.2 mm, exit velocity 0.1-2.2 m/sec, 4- and 6-component methane-based fuel mixtures representative of associated gas in the upstream oil industry), measured soot emission factors were less than 0.84 kg soot/10(3) m3 fuel. A simple empirical relationship is presented to estimate the PM emission factor as a function of the fuel heating value for a range of conditions, which, although still limited, is an improvement over currently available emission factors.

  8. Covalent Functionalization of Multiwalled Carbon Nanotubes with Poly(acrylic acid)

    Institute of Scientific and Technical Information of China (English)

    LIU, Yan-Xin; DU, Zhong-Jie; LI, Yan; ZHANG, Chen; LI, Hang-Quan

    2006-01-01

    Covalent functionalization of multiwalled carbon nanotubes (MWNT) with poly(acrylic acid) has been successfully achieved via grafting of poly(acryloyl chloride) on nanotube surface by esterification reaction of acyl chloride-bound polymer with hydroxyl functional groups present on acid-oxidized MWNT and hydrolysis of polymer attached to nanotubes. Polymer-functionalized MWNT could possess remarkably high solubility in water, and their aqueous solution was very stable without any observable black deposit for a long time. Characterizations of such functionalized MWNT samples using Fourier transform infrared spectrometer, transmission electron microscopy and nuclear magnetic resonance techniques indicated that poly(acrylic acid) was covalently attached to the surface of MWNT.

  9. Observations of Black Carbon and Aerosol Optical Depth in the Kali Gandaki Valley, Nepal

    Science.gov (United States)

    Dhungel, S.; Panday, A. K.; Mahata, K. S.

    2012-12-01

    During recent years there has been increasing concern about the deposition of black carbon from the Indo-Gangetic Plains onto the glaciers and snowfields of the Tibetan Plateau. There has also been increasing concern about the rapid increase in air temperature at high altitudes over the Tibetan Plateau and the Himalaya. To date, there is very little knowledge about the transport pathways for pollutants traveling from the Indo-Gangetic Plains across the Himalaya to the Tibetan Plateau. The Kali Gandaki Valley in Nepal is one of the deepest gorges in the world, and has some of the highest up-valley winds in the world. It is also one of the most open connecting points for air from South Asia to reach the Tibetan Plateau. In 2010 the University of Virginia, in collaboration with ICIMOD and Nepal Wireless, established an atmospheric research station in Jomsom, Nepal (28.78N, 83.42E, 2900 m.a.s.l.). The station is equipped to measure black carbon (BC), carbon monoxide (CO), and ozone concentrations. It also has an automated weather station, a filter sampler, and a NASA Aeronet Sunphotometer. Observations of BC and aerosol optical depth (AOD) from Aeronet are analyzed and presented. Diurnal and seasonal patterns of BC have been observed with higher values during the day and lower at night and also highest during pre-monsoon and lowest during monsoon season, with observed BC concentrations exceeding 5 μg while average concentration around 3.7 μg.

  10. Use of carbon filaments in place of carbon black as the current collector of a lithium cell with a thionyl chloride bromine chloride catholyte

    Science.gov (United States)

    Frysz, Christine A.; Shui, Xiaoping; Chung, D. D. L.

    Submicron carbon filaments (ADNH, Applied Sciences Inc.) used in place of carbon black as porous reduction electrodes (i.e., current collectors) in plate and jellyroll configurations in carbon limited lithium batteries with the BCX (bromine chloride in thionyl chloride) catholyte gave a specific capacity (at 2 V cut-off) of up to 8700 mAh/g of carbon, compared with a value of up to 2900 mAh/g of carbon for carbon black. The high specific capacity for the filament electrode is partly due to the filaments' processability into sheets as thin as 0.2 mm with good porosity, acceptable mechanical properties and without binder, and partly due to the high catholyte absorptivity and high rate of catholyte absorption of the filament electrode. Use of solvent-cleansed filaments in place of as-received filaments in making electrodes increased the packing density, thus decreasing capacity per g of carbon. The BCX catholyte acted as a cleanser anyway, due to the thionyl chloride in it. The specific capacity per cm 3 of carbon and that per unit density of carbon were also increased by using carbon filaments in place of carbon black, provided that the filament electrode was not pressed after forming by slurry filtration. Though no binder was needed for the filament plate electrode, it was needed for the filament jellyroll electrode. The Teflon™ binder increased the tensile strength and modulus, but decreased the catholyte absorption and rate of absorption. The filament electrode exhibited 405 less volume electrical resistivity than the carbon black electrode, both without a binder.

  11. Ambient measurements and source apportionment of fossil fuel and biomass burning black carbon in Ontario

    Science.gov (United States)

    Healy, R. M.; Sofowote, U.; Su, Y.; Debosz, J.; Noble, M.; Jeong, C.-H.; Wang, J. M.; Hilker, N.; Evans, G. J.; Doerksen, G.; Jones, K.; Munoz, A.

    2017-07-01

    Black carbon (BC) is of significant interest from a human exposure perspective but also due to its impacts as a short-lived climate pollutant. In this study, sources of BC influencing air quality in Ontario, Canada were investigated using nine concurrent Aethalometer datasets collected between June 2015 and May 2016. The sampling sites represent a mix of background and near-road locations. An optical model was used to estimate the relative contributions of fossil fuel combustion and biomass burning to ambient concentrations of BC at every site. The highest annual mean BC concentration was observed at a Toronto highway site, where vehicular traffic was found to be the dominant source. Fossil fuel combustion was the dominant contributor to ambient BC at all sites in every season, while the highest seasonal biomass burning mass contribution (35%) was observed in the winter at a background site with minimal traffic contributions. The mass absorption cross-section of BC was also investigated at two sites, where concurrent thermal/optical elemental carbon data were available, and was found to be similar at both locations. These results are expected to be useful for comparing the optical properties of BC at other near-road environments globally. A strong seasonal dependence was observed for fossil fuel BC at every Ontario site, with mean summer mass concentrations higher than their respective mean winter mass concentrations by up to a factor of two. An increased influence from transboundary fossil fuel BC emissions originating in Michigan, Ohio, Pennsylvania and New York was identified for the summer months. The findings reported here indicate that BC should not be considered as an exclusively local pollutant in future air quality policy decisions. The highest seasonal difference was observed at the highway site, however, suggesting that changes in fuel composition may also play an important role in the seasonality of BC mass concentrations in the near-road environment

  12. Dielectric study of Poly(styrene- co -butadiene) Composites with Carbon Black, Silica, and Nanoclay

    KAUST Repository

    Vo, Loan T.

    2011-08-09

    Dielectric spectroscopy is used to measure polymer relaxation in styrene-butadiene rubber (SBR) composites. In addition to the bulk polymer relaxation, the SBR nanocomposites also exhibit a slower relaxation attributed to polymer relaxation at the polymer-nanoparticle interface. The glass transition temperature associated with the slower relaxation is used as a way to quantify the interaction strength between the polymer and the surface. Comparisons were made among composites containing nanoclay, silica, and carbon black. The interfacial relaxation glass transition temperature of SBR-clay nanocomposites is more than 80 °C higher than the SBR bulk glass transition temperature. An interfacial mode was also observed for SBR-silica nanocomposites, but the interfacial glass transition temperature of SBR-silica nanocomposite is somewhat lower than that of clay nanocomposites. An interfacial mode is also seen in the carbon black filled system, but the signal is too weak to analyze quantitatively. The interfacial polymer relaxation in SBR-clay nanocomposites is stronger compared to both SBR-carbon black and SBR-silica composites indicating a stronger interfacial interaction in the nanocomposites containing clay. These results are consistent with dynamic shear rheology and dynamic mechanical analysis measurements showing a more pronounced reinforcement for the clay nanocomposites. Comparisons were also made among clay nanocomposites using different SBRs of varying styrene concentration and architecture. The interfacial glass transition temperature of SBR-clay nanocomposites increases as the amount of styrene in SBR increases indicating that styrene interacts more strongly than butadiene with clay. © 2011 American Chemical Society.

  13. Aerosol black carbon at five background measurement sites over Finland, a gateway to the Arctic

    Science.gov (United States)

    Hyvärinen, A.-P.; Kolmonen, P.; Kerminen, V.-M.; Virkkula, A.; Leskinen, A.; Komppula, M.; Hatakka, J.; Burkhart, J.; Stohl, A.; Aalto, P.; Kulmala, M.; Lehtinen, K. E. J.; Viisanen, Y.; Lihavainen, H.

    2011-08-01

    Aerosol equivalent black carbon (BC e) was measured at five different background stations in Finland, with the longest data set from Hyytiälä, December 2004-December 2008. Measurements were conducted either with an aethalometer or a Multi-Angle Absorption Photometer, MAAP. Measured black carbon concentrations were highest in Virolahti in southeastern Finland, with annual averages ranging from 385 to 460 ng m -3, followed by Hyytiälä (250-370 ng m -3), Utö (230-270 ng m -3), Puijo (225-230 ng m -3), and Pallastunturi (60-70 ng m -3) in northern Finland. The BC e fractions of measured PM 2.5 concentrations were generally between 5 and 10%, with highest fractions at Virolahti close to the Eastern border. At all the stations, the highest concentrations were observed during the spring and the winter, and the lowest concentrations during the summer. The seasonal cycle could generally be attributed to the reaching of long-range-transported black carbon. Additional reasons were increasing domestic wood burning and reduced boundary-layer height during winter, and a more effective vertical mixing during summer. The highest concentrations for each station occurred with southerly winds, and on the basis of trajectory analyses, the source areas of BC e resided mostly in Central and Eastern Europe. Occasionally the long-range-transported BC e concentrations were elevated for short periods to fulfill the characteristics of pollution episodes. From these episodes, about 62% were a result of non-fire anthropogenic sources and 36% due to open biomass burning sources. Episodes from the biomass burning sources were most often observed during the spring.

  14. Improvement of water/resin wettability of graphite using carbon black nano particles coating via ink media

    Energy Technology Data Exchange (ETDEWEB)

    Sharif, M., E-mail: Sharif_m@metaleng.iust.ac.i [Iran University of Science and Technology (Iran, Islamic Republic of); Golestani-Fard, F.; Sarpoolaky, H. [Iran University of Science and Technology (Iran, Islamic Republic of)

    2009-08-12

    Carbon coated graphite with high resin and water wettability characteristics could expand the refractory and carbon-carbon composites application in different fields. Improvement of water and resin wettability of graphite using carbon black coating via ink media is reported. Present method is based on preparing colloidal disperion of carbon black in ink followed by adding proper amount of graphite to the mixture which was dried and heat treated at 250 deg. C afterwards. The results showed that by controlling the amount of carbon black in ink and optimizing the process, a uniform coating with a thickness of 50 nm could be developed on the graphite surface. The wettability was evaluated by measuring contact angle and the microstructure of samples was characterized by optic microscope (OM) and scanning electron microscope (SEM). Also Raman spectroscopy was employed to support the results. The microstructure of coating was found to be uniform composed of carbon black nanoparticles. It was also demonstrated that the coating that could enhance the phenolic resin wettability was well. We also showed the coating could be applied on other ceramic particles such as MgO.

  15. 雪冰中黑碳的研究进展%Research Progress of Black Carbon in Snow and Ice

    Institute of Scientific and Technical Information of China (English)

    刘昌明; 党素珍; 王中根; 王书功

    2012-01-01

    Black carbon aerosol is an important component of the atmospheric aerosols. When it is settled in snow and ice,it can decrease the reflectivity of the surface of snow and ice. As a result.it can affect the melting process of snow and ice,and lead to the potential global and regional climate change. In addition, the radiative forcing effects of black carbon in snow and ice are of great concern. China discharges lots of black carbon aerosol, therefore the issues of black carbon in snow and ice merit the attention. This paper describes briefly the importance of the study of black carbon in snow and ice, and emphasizes the sources and historical environmental records of black carbon in snow and ice, and the calculation method of the effects of black carbon on the reflectivity in snow and ice and the radiative forcing effects of black carbon. Finally, this paper presents the prospect of the study of black carbon in snow and ice,and proposes three aspects of research which needs to be further strengthened.%黑碳气溶胶是大气气溶胶的一种重要成分,沉降在雪冰中可减小雪冰表面的反照率,影响雪冰的融化过程,导致全球和区域气候变化.黑碳气溶胶沉降在雪冰中产生的辐射强迫效应值得关注.中国是黑碳气溶胶排放大国,雪冰黑碳的问题值得关注.现简要介绍雪冰中黑碳研究的意义,着重综述雪冰中黑碳的来源,历史环境记录,现有的计算雪冰中黑碳对反照率影响的方法以及其辐射强迫效应的研究.对未来雪冰中黑碳的研究进行了展望,提出3点今后需加强研究的内容.

  16. Associations between Prenatal Exposure to Black Carbon and Memory Domains in Urban Children: Modification by Sex and Prenatal Stress.

    Science.gov (United States)

    Cowell, Whitney J; Bellinger, David C; Coull, Brent A; Gennings, Chris; Wright, Robert O; Wright, Rosalind J

    2015-01-01

    Whether fetal neurodevelopment is disrupted by traffic-related air pollution is uncertain. Animal studies suggest that chemical and non-chemical stressors interact to impact neurodevelopment, and that this association is further modified by sex. To examine associations between prenatal traffic-related black carbon exposure, prenatal stress, and sex with children's memory and learning. Analyses included N = 258 mother-child dyads enrolled in a Boston, Massachusetts pregnancy cohort. Black carbon exposure was estimated using a validated spatiotemporal land-use regression model. Prenatal stress was measured using the Crisis in Family Systems-Revised survey of negative life events. The Wide Range Assessment of Memory and Learning (WRAML2) was administered at age 6 years; outcomes included the General Memory Index and its component indices [Verbal, Visual, and Attention Concentration]. Relationships between black carbon and WRAML2 index scores were examined using multivariable-adjusted linear regression including effect modification by stress and sex. Mothers were primarily minorities (60% Hispanic, 26% Black); 67% had ≤12 years of education. The main effect for black carbon was not significant for any WRAML2 index; however, in stratified analyses, among boys with high exposure to prenatal stress, Attention Concentration Index scores were on average 9.5 points lower for those with high compared to low prenatal black carbon exposure (P3-way interaction = 0.04). The associations between prenatal exposure to black carbon and stress with children's memory scores were stronger in boys than in girls. Studies assessing complex interactions may more fully characterize health risks and, in particular, identify vulnerable subgroups.

  17. PM2.5 and aerosol black carbon in Suva, Fiji

    Science.gov (United States)

    Isley, C. F.; Nelson, P. F.; Taylor, M. P.; Mani, F. S.; Maata, M.; Atanacio, A.; Stelcer, E.; Cohen, D. D.

    2017-02-01

    Concentrations of particulate air pollution in Suva, Fiji, have been largely unknown and consequently, current strategies to reduce health risk from air pollution in Suva are not targeted effectively. This lack of air quality data is common across the Pacific Island Countries. A monitoring study, during 2014 and 2015, has characterised the fine particulate air quality in Suva, representing the most detailed study to date of fine aerosol air pollutants for the Pacific Islands; with sampling at City, Residential (Kinoya) and Background (Suva Point) sites. Meteorology for Suva, as it relates to pollutant dispersion for this period of time, has also been analysed. The study design enables the contribution of maritime air and the anthropogenic emissions to be carefully distinguished from each other and separately characterised. Back trajectory calculations show that a packet of air sampled at the Suva City site has typically travelled 724 km in the 24-h prior to sampling, mainly over open ocean waters; inferring that pollutants would also be rapidly transported away from Suva. For fine particulates, Suva City reported a mid-week PM2.5 of 8.6 ± 0.4 μg/m3, averaged over 13-months of gravimetric sampling. Continuous monitoring (Osiris laser photometer) suggests that some areas of Suva may experience levels exceeding the WHO PM2.5 guideline of 10 μg/m3, however, compared to other countries, Fiji's PM2.5 is low. Peak aerosol particulate levels, at all sites, were experienced at night-time, when atmospheric conditions were least favourable to dispersion of air pollutants. Suva's average ambient concentrations of black carbon in PM2.5, 2.2 ± 0.1 μg/m3, are, however, similar to those measured in much larger cities. With any given parcel of air spending only seven minutes, on average, over the land area of Suva Peninsula, these black carbon concentrations are indicative that significant combustion emissions occur within Suva. Many other communities in the Pacific Islands

  18. GHG and black carbon emission inventories from Mezquital Valley: The main energy provider for Mexico Megacity

    Energy Technology Data Exchange (ETDEWEB)

    Montelongo-Reyes, M.M.; Otazo-Sánchez, E.M.; Romo-Gómez, C.; Gordillo-Martínez, A.J.; Galindo-Castillo, E.

    2015-09-15

    The greenhouse gases and black carbon emission inventory from IPCC key category Energy was accomplished for the Mezquital Valley, one of the most polluted regions in Mexico, as the Mexico City wastewater have been continuously used in agricultural irrigation for more than a hundred years. In addition, thermoelectric, refinery, cement and chemistry industries are concentrated in the southern part of the valley, near Mexico City. Several studies have reported air, soil, and water pollution data and its main sources for the region. Paradoxically, these sources contaminate the valley, but boosted its economic development. Nevertheless, no research has been done concerning GHG emissions, or climate change assessment. This paper reports inventories performed by the 1996 IPCC methodology for the baseline year 2005. Fuel consumption data were derived from priority sectors such as electricity generation, refineries, manufacturing & cement industries, transportation, and residential use. The total CO{sub 2} emission result was 13,894.9 Gg, which constituted three-quarters of Hidalgo statewide energy category. The principal CO{sub 2} sources were energy transformation (69%) and manufacturing (19%). Total black carbon emissions were estimated by a bottom-up method at 0.66 Gg. The principal contributor was on-road transportation (37%), followed by firewood residential consumption (26%) and cocked brick manufactures (22%). Non-CO{sub 2} gas emissions were also significant, particularly SO{sub 2} (255.9 Gg), which accounts for 80% of the whole Hidalgo State emissions. Results demonstrated the negative environmental impact on Mezquital Valley, caused by its role as a Megacity secondary fuel and electricity provider, as well as by the presence of several cement industries. - Highlights: • First GHG & black carbon inventory for Mezquital Valley: Mexico City energy supplier • Energy industries caused the largest CO{sub 2} and SO{sub 2} emissions from residual fuel oil. • Diesel

  19. High Voltage Surface Degradation on Carbon Blacks in Lithium Ion Batteries

    DEFF Research Database (Denmark)

    Younesi, Reza

    including carbon black (CB) additives have a potential risk of degradation. Though the weight percentage of CB in commercial batteries is generally very small, the volumetric amount and thus the surface area of CB compose a rather large part of a cathode due to its small particle size (≈ 50 nm) and high......In order to increase the power density of Li-ion batteries, much research is focused on developing cathode materials that can operate at high voltages above 4.5 V with a high capacity, high cycling stability, and rate capability. However, at high voltages all the components of positive electrodes...

  20. Electrothermal Performances of Poly(Vinylidiene Fluoride)/Fluorine Rubber Conductive Composite Filled with Carbon Black

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ The conductive polymer composites and their corresponding resistors with PTC (positive temperature coefficient) characteristic can be manufactured by mixing conductive carbon blacks with poly(vinylidiene fluoride )matrix. The Joule heat can produce when alternative voltage is exerted on the composite resistors, and the resistors can produce when alternative voltage is exerted on the current from flowing at a high temperature because of their PTC effect, thus becoming a kind of important thermoelectric switching materials as heating, temperature-controlling and currentlinfiting element applications.

  1. Electrothermal Performances of Poly(Vinylidiene Fluoride)/Fluorine Rubber Conductive Composite Filled with Carbon Black

    Institute of Scientific and Technical Information of China (English)

    LUO; YanLing

    2001-01-01

    The conductive polymer composites and their corresponding resistors with PTC (positive temperature coefficient) characteristic can be manufactured by mixing conductive carbon blacks with poly(vinylidiene fluoride )matrix. The Joule heat can produce when alternative voltage is exerted on the composite resistors, and the resistors can produce when alternative voltage is exerted on the current from flowing at a high temperature because of their PTC effect, thus becoming a kind of important thermoelectric switching materials as heating, temperature-controlling and currentlinfiting element applications.  ……

  2. Effect of carbon black on the properties of irradiated recycled polyamide/rubber waste composites

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, Medhat M., E-mail: medhat_smh@yahoo.co [National Center for Radiation Research and Technology, Nasr City, Cairo 11731 (Egypt); Badway, Nagwa A.; Gamal, Azza M. [Chemistry Department, Faculty of Science, Al-Azhar University, Nasr City, Cairo (Egypt); Elnaggar, Mona Y.; Hegazy, El-Sayed A. [National Center for Radiation Research and Technology, Nasr City, Cairo 11731 (Egypt)

    2010-08-15

    In the present study, the synergistic effect of carbon black (CB) content % and gamma irradiation on some mechanical, thermal, chemical stability and micro-structural properties of the moulded waste polyamide copolymer/recycled waste rubber powder (rPA/WRP) 50/50 was investigated. The ternary composites of CB concentrations, 6, 12, 18, and 24 wt.%, were irradiated with doses of 50, 100, 150 and 200 kGy. The composites mechanical properties: tensile strength, elongation at break, and hardness, and the thermal properties: melting temperature (T{sub m}) and ({Delta}H) were measured. Also, scanning electron microscopy (SEM), thermogravimetric analysis (TGA), swelling and chemical stability were investigated.

  3. High Voltage Surface Degradation on Carbon Blacks in Lithium Ion Batteries

    DEFF Research Database (Denmark)

    Younesi, Reza

    In order to increase the power density of Li-ion batteries, much research is focused on developing cathode materials that can operate at high voltages above 4.5 V with a high capacity, high cycling stability, and rate capability. However, at high voltages all the components of positive electrodes...... including carbon black (CB) additives have a potential risk of degradation. Though the weight percentage of CB in commercial batteries is generally very small, the volumetric amount and thus the surface area of CB compose a rather large part of a cathode due to its small particle size (≈ 50 nm) and high...

  4. Sorption capacities of graphitzed carbon black in determination of chlorinate pesticide traces in water

    Energy Technology Data Exchange (ETDEWEB)

    Bacaloni, A.; Goretti, G.; Lagana, A.; Petronio, B.M.; Rotatori, M.

    1980-11-01

    The use of graphitized carbon black (GCB) to extract trace organic pollutants from water is analyzed. Adsorbent materials such as GCB or Tenax can be used to determine low concentrations of organic pollutants in water. The adsorption ability of GCB vs. that of Tenax was tested with 51 different compounds including alcohols, acids, phenols, ethers, hydrocarbons,and PCB's at concentrations ranging from 5 ppb to 200 ppb. Chlorinated pesticides were among the compounds that were entirely adsorbed. Although the adsorbent efficiences depend on the nature of other substances in the water samples, GCB proves to be better than Tenax for pesticide determinations. (6 graphs, 17 references, 4 tables)

  5. SP2 Deployment at Boston College—Aerodyne-Led Coated Black Carbon Study (BC4) Final Campaign Summary

    Energy Technology Data Exchange (ETDEWEB)

    Onasch, T. B. [Aerodyne Research, Inc., Billerica, MA (United States); Sedlacek, A. J. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-03-01

    The main objective of the Boston College-Aerodyne led laboratory study (BC4) was to measure the optical properties of black carbon (BC) particles from a diffusion flame directly and after being coated with secondary organic and inorganic material and to achieve optical closure with model predictions. The measurements of single particle BC mass and population mixing states provided by a single particle soot photometer (SP2) was central to achieving the laboratory-based study’s objective. Specifically, the DOE ARM SP2 instrument participated in the BC4 project to address the following scientific questions: 1. What is the mass-specific absorption coefficient as a function of secondary organic and inorganic material coatings? 2. What is the spread in the population mixing states within our carefully generated laboratory particles? 3. How does the SP2 instrument respond to well-characterized, internally mixed BC-containing particles?

  6. Preservation of black carbon in the shelf sediments of the East China Sea

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Concentrations and carbon isotopic (14C, 13C) compositions of black carbon (BC) were measured for three sediment cores collected from the Changjiang River estuary and the shelf of the East China Sea. BC concentrations ranged from 0.02 to 0.14 mg/g (dry weight), and accounted for 5% to 26% of the sedimentary total organic carbon (TOC) pool. Among the three sediment cores collected at each site, sediment from the Changjiang River estuary had relatively high BC contents compared with the sediments from the East China Sea shelf, suggesting that the Changjiang River discharge played an important role in the delivery of BC to the coastal region. Radiocarbon measurements indicate that the ages of BC are in the range of 6910 to 12250 years old B.P. (before present), that is in general, 3700 to 9000 years older than the 14C ages of TOC in the sediments. These variable radiocarbon ages suggest that the BC preserved in the sediments was derived from the products of both biomass fire and fossil fuel combustion, as well as from ancient rock weathering. Based on an isotopic mass balance model, we calculated that fossil fuel combustion contributed most (60%―80%) of the BC preserved in these sediments and varied with depth and locations. The deposition and burial of this "slow-cycling" BC in the sediments of the East China Sea shelf represent a significant pool of carbon sink and could greatly in-fluence carbon cycling in the region.

  7. Comparing black carbon types in sequestering polybrominated diphenyl ethers (PBDEs) in sediments.

    Science.gov (United States)

    Jia, Fang; Gan, Jay

    2014-01-01

    Polybrominated diphenyl ethers (PBDEs) are widely found in sediments, especially congeners from the penta-BDE formula. Due to their strong affinity for black carbon (BC), bioavailability of PBDEs may be decreased in BC-amended sediments. In this study, we used a matrix-SPME method to measure the freely dissolved concentration (Cfree) of PBDEs as a parameter of their potential bioavailability and evaluated the differences among biochar, charcoal, and activated carbon. Activated carbon displayed a substantially greater sequestration capacity than biochar or charcoal. At 1% amendment rate in sediment with low organic carbon (OC) content (0.12%), Cfree of six PBDEs was reduced by 47.5-78.0%, 47.3-77.5%, and 94.1-98.3% with biochar, charcoal, and activated carbon, respectively, while the sequestration was more limited in sediment with high OC content (0.87%). Therefore, it is important to consider the type and properties of the BC and the sediment in BC-based remediation or mitigation.

  8. The functional significance of black-pigmented leaves: photosynthesis, photoprotection and productivity in Ophiopogon planiscapus 'Nigrescens'.

    Directory of Open Access Journals (Sweden)

    Jean-Hugues B Hatier

    Full Text Available Black pigmented leaves are common among horticultural cultivars, yet are extremely rare across natural plant populations. We hypothesised that black pigmentation would disadvantage a plant by reducing photosynthesis and therefore shoot productivity, but that this trait might also confer protective benefits by shielding chloroplasts against photo-oxidative stress. CO2 assimilation, chlorophyll a fluorescence, shoot biomass, and pigment concentrations were compared for near isogenic green- and black-leafed Ophiopogonplaniscapus 'Nigrescens'. The black leaves had lower maximum CO2 assimilation rates, higher light saturation points and higher quantum efficiencies of photosystem II (PSII than green leaves. Under saturating light, PSII photochemistry was inactivated less and recovered more completely in the black leaves. In full sunlight, green plants branched more abundantly and accumulated shoot biomass quicker than the black plants; in the shade, productivities of the two morphs were comparable. The data indicate a light-screening, photoprotective role of foliar anthocyanins. However, limitations to photosynthetic carbon assimilation are relatively small, insufficient to explain the natural scarcity of black-leafed plants.

  9. The functional significance of black-pigmented leaves: photosynthesis, photoprotection and productivity in Ophiopogon planiscapus 'Nigrescens'.

    Science.gov (United States)

    Hatier, Jean-Hugues B; Clearwater, Michael J; Gould, Kevin S

    2013-01-01

    Black pigmented leaves are common among horticultural cultivars, yet are extremely rare across natural plant populations. We hypothesised that black pigmentation would disadvantage a plant by reducing photosynthesis and therefore shoot productivity, but that this trait might also confer protective benefits by shielding chloroplasts against photo-oxidative stress. CO2 assimilation, chlorophyll a fluorescence, shoot biomass, and pigment concentrations were compared for near isogenic green- and black-leafed Ophiopogonplaniscapus 'Nigrescens'. The black leaves had lower maximum CO2 assimilation rates, higher light saturation points and higher quantum efficiencies of photosystem II (PSII) than green leaves. Under saturating light, PSII photochemistry was inactivated less and recovered more completely in the black leaves. In full sunlight, green plants branched more abundantly and accumulated shoot biomass quicker than the black plants; in the shade, productivities of the two morphs were comparable. The data indicate a light-screening, photoprotective role of foliar anthocyanins. However, limitations to photosynthetic carbon assimilation are relatively small, insufficient to explain the natural scarcity of black-leafed plants.

  10. Morphology and Mixing of Black Carbon Particles Collected in Central California During the CARES Field Study

    Energy Technology Data Exchange (ETDEWEB)

    Moffet, Ryan; O' Brien, Rachel; Alpert, Peter A.; Kelly, Stephen T.; Pham, Don Q.; Gilles, Mary K.; Knopf, Daniel A.; Laskin, Alexander

    2016-11-23

    Aerosol absorption is strongly dependent on the internal heterogeneity (mixing state) and morphology of individual particles containing black carbon (BC) and other non-absorbing species. Here, we examine an extensive microscopic data set collected in the California central valley during the CARES 2010 field campaign. During a period of high photochemical activity and pollution buildup, the particle mixing state and morphology were characterized using Scanning Transmission X-ray Microscopy (STXM) at the carbon K-edge. Observations of compacted BC core morphologies and thick organic coatings at both urban and rural sites provide evidence of the aged nature of the particles. Based on the observation of thick coatings and more convex BC inclusion morphology, the contribution of fresh BC emissions at the urban site was relatively small. These measurements of BC morphology and mixing state provide important constraints for the morphological effects on BC optical properties expected in aged urban plumes.

  11. Functional limitations and nativity status among older Arab, Asian, black, Hispanic, and white Americans.

    Science.gov (United States)

    Dallo, Florence J; Booza, Jason; Nguyen, Norma D

    2015-04-01

    To examine the association between nativity status (foreign and US-born) by race/ethnicity (Arab, Asian, black, Hispanic, white) on having a functional limitation. We used American Community Survey data (2001-2007; n = 1,964,777; 65+ years) and estimated odds ratios (95% confidence intervals). In the crude model, foreign-born Blacks and Arabs were more likely, while Asians and Hispanics were less likely to report having a functional limitation compared to white. In the fully adjusted model, Blacks, Hispanics, and Asians were less likely, while Arabs were more likely to report having a functional limitation. In the crude model, US-born Blacks and Hispanics were more likely, while Asians and Arabs were less likely to report having a functional limitation compared to whites. Policies and programs tailored to foreign-born Arab Americans may help prevent or delay the onset of disability, especially when initiated shortly after their arrival to the US.

  12. Distribution and preservation of black carbon in the East China Sea sediments: Perspectives on carbon cycling at continental margins

    Science.gov (United States)

    Huang, Liang; Zhang, Jing; Wu, Ying; Wang, Jinlong

    2016-02-01

    We determined the concentrations and radiocarbon (14C) compositions of black carbon (BC) in the sediments of the East China Sea (ECS). The BC concentrations, which were in the range of 0.30-1.52 mg/g, accounted for 12-65% of the total organic carbon (TOC). The distribution of BC in ECS sediments was controlled by factors such as grain size, distance from the coast, and deposition rate. Radiocarbon measurements of BC yielded ages of 6350-10,440 years before present (BP), suggesting that the percentage of BC derived from biomass combustion was in the range of 29-48%. The BC burial flux in sediments of the ECS was estimated to be ∼1.39×106 t/yr, which was similar to burial fluxes reported for shelf sediments in other areas. However, the magnitude of the total BC sink was far greater than that of any other shelf regions studied to date, indicating the global importance of BC accumulation in the ECS, and the magnitude of BC input from large rivers (e.g., the Changjiang). The riverine delivery of BC to the ECS (73%) was far greater than that of atmospheric flux (27%). Further study of the BC cycle and the interactions of BC with other organic compounds in marginal seas was required to better understand the role of BC in the global carbon cycle.

  13. Intercomparison of thermal and optical measurement methods for elemental carbon and black carbon at an urban location.

    Science.gov (United States)

    Hitzenberger, R; Petzold, A; Bauer, H; Ctyroky, P; Pouresmaeil, P; Laskus, L; Puxbaum, H

    2006-10-15

    Despite intensive efforts during the past 20 years, no generally accepted standard method exists to measure black carbon (BC) or elemental carbon (EC). Data on BC and EC concentrations are method specific and can differ widely (e.g. Schmid et al., 2001, ten Brink et al., 2004). In this study, a comprehensive set of methods (both optical and thermal) is compared. Measurements were performed under urban background conditions in Vienna, Austria, a city heavily impacted by diesel emissions. Filter and impactor samples were taken during 3 weeks in summer 2002 and analyzed for EC with thermal methods: a modified Cachier method (Cachier et al., 1989), a thermal-optical method (Schmid et al., 2001), and the VDI method (VDI, 1996); for BC with optical methods: a filter transmission method and the integrating sphere method (Hitzenberger et al., 1996); and for total carbon (TC) with a combustion method (Puxbaum and Rendl, 1983). The online methods aethalometer (Hansen et al., 1984) and the multiangle absorption photometer MAAP (Petzold et al., 2002) to measure BC were also used. The average values of BC and EC obtained with the methods agreed within their standard deviations. A conversion table was set up to allow comparisons between data measured elsewhere under urban background conditions (with similar source characteristics) with different instruments. An approach to estimate the absorption coefficient from attenuation data is derived so that existing records of aethalometer data in urban environments may be used to obtain also the absorption coefficients.

  14. Novel single-layer gas diffusion layer based on PTFE/carbon black composite for proton exchange membrane fuel cell

    Energy Technology Data Exchange (ETDEWEB)

    Chen-Yang, Y.W.; Hung, T.F.; Yang, F.L. [Department of Chemistry and Center for Nanotechnology, Chung Yuan Christian University, Chung-Li 32023 (China); Huang, J. [Yeu Ming Tai Chemical Industrial Co., Ltd, Taichung 40768 (China)

    2007-11-08

    A series of poly(tetrafluoroethylene)/carbon black composite-based single-layer gas diffusion layers (PTFE/CB-GDLs) for proton exchange membrane fuel cell (PEMFC) was successfully prepared from carbon black and un-sintered PTFE, which included powder resin and colloidal dispersion, by a simple inexpensive method. The scanning electron micrographs of PTFE/CB-GDLs indicated that the PTFE resins were homogeneously dispersed in the carbon black matrix and showed a microporous layer (MPL)-like structure. The as-prepared PTFE/CB-GDLs exhibited good mechanical property, high gas permeability, and sufficient water repellency. The best current density obtained from the PEMFC with the single-layer PTFE/CB-GDL was 1.27 and 0.42 A cm{sup -2} for H{sub 2}/O{sub 2} and H{sub 2}/air system, respectively. (author)

  15. Determination of the free energy of adsorption on carbon blacks of a nonionic surfactant from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Garcia, C.M.; Gonzalez-Martin, M.L.; Gomez-Serrano, V.; Bruque, J.M.; Labajos-Broncano, L.

    2000-04-18

    The adsorption of a nonionic surfactant (Triton X-100) from aqueous solutions has been studied on six carbon blacks with very different specific surface areas. The surface area occupied per surfactant molecule on the carbon black surface and the free energy of adsorption have been evaluated from the adsorption isotherms. Also, the free energy of adsorption has been determined from the free energy of interaction between adsorbent and adsorbate through water. The results obtained from both methods are in good agreement. They indicate that adsorption progresses following two different processes: the first one deals with the direct interaction between carbon black surface and adsorbate molecules, and the second one mainly due to the interaction between surfactant molecules at the adsorbent-solution interphase.

  16. Contribution of regional transport to the black carbon aerosol during winter haze period in Beijing

    Science.gov (United States)

    Wang, Qiyuan; Huang, Ru-Jin; Cao, Junji; Tie, Xuexi; Shen, Zhenxing; Zhao, Shuyu; Han, Yongming; Li, Guohui; Li, Zhengqiang; Ni, Haiyan; Zhou, Yaqing; Wang, Meng; Chen, Yang; Su, Xiaoli

    2016-05-01

    The mass concentrations of atmospheric refractory black carbon (rBC), an important absorber of solar radiation, were continuously measured with a single particle soot photometer (SP2) during wintertime haze period to investigate the transport of pollution to Beijing. The average mass concentration of rBC was 6.1 ± 3.9 μg m-3 during hazy periods, which was 4.7 times higher than it during non-hazy periods. Cluster analysis showed that the air parcels arriving at Beijing mainly originated from the northwest, passed through the south and brought the most polluted air to Beijing. Concentration-weighted trajectory analyses indicated that the central North China Plain were the most likely source region for the rBC that impacted Beijing. Furthermore, the Weather Research and Forecasting-Black Carbon model showed that 71.4-82.0% of the rBC at Beijing was from regional transport during the high rBC episodes and that 47.9-56.8% of the rBC can be attributed to sources in the central North China Plain. These results suggest that regional transport from the central North China Plain, rather than local emissions, was a more important source for rBC pollution in Beijing.

  17. Synthesis of Cordierite by Decomposition of Metal Nitrates on the Surface of Carbon Black Powder

    Institute of Scientific and Technical Information of China (English)

    XIE Zhi-yong; LIANG Hui; XU Ming-xia; XU Ting-xian

    2004-01-01

    Cordierite precursor was obtained through a process, which involved the decomposition of metal nitrates on the surface of ultrafine carbon black powder between 100-300℃ and the gasification of the carbon black at higher temperature in air. The average size of the particles, which were heat-treated at 700℃ for 10h, is about 1020nm, and the specific surface area is about 129m2/g. The experimental results show that the ultrafine particles of cordierite precursor can be produced by this process. The precursor powder was calcined at different temperatures. X-ray diffraction examination indicates that β-quartz is crystallized from the amorphous matrix around 850℃ firstly and then MgO-Al2O3 spinel and α-cordierite appears. Above 1000℃, MgO-Al2O3 spinel and cristobalite disappear gradually and form an intermediate phase (sapphirine). At around 1300℃, the main phase is α-cordierite, and no other phase is detected.

  18. Measured black carbon deposition on the Sierra Nevada snow pack and implication for snow pack retreat

    Directory of Open Access Journals (Sweden)

    O. L. Hadley

    2010-04-01

    Full Text Available Modeling studies show that the darkening of snow and ice by black carbon (BC deposition is a major factor for the rapid disappearance of arctic sea ice, mountain glaciers and snow packs. This study provides one of the first direct measurements for the efficient removal of black carbon from the atmosphere by snow and its subsequent deposition on the snow packs of California. The early melting of the snow packs in the Sierras is one of the contributing factors to the severe water problems in California. BC concentrations in falling snow were measured at two mountain locations and in rain at a coastal site. All three stations reveal large BC concentrations in precipitation, ranging from 1.7 ng/g to 12.9 ng/g. The BC concentrations in the air after the snow fall were negligible suggesting an extremely efficient removal of BC by snow. The data suggest that below cloud scavenging, rather than ice nuclei, was the dominant source of BC in the snow. A five-year comparison of BC, dust, and total fine aerosol mass concentrations at multiple sites reveals that the measurements made at the sampling sites were representative of large scale deposition in the Sierra Nevada. The relative concentration of iron and calcium in the mountain aerosol indicates that one-quarter to one-third of the BC may have been transported from Asia.

  19. Measured black carbon deposition on the Sierra Nevada snow pack and implication for snow pack retreat

    Directory of Open Access Journals (Sweden)

    O. L. Hadley

    2010-08-01

    Full Text Available Modeling studies show that the darkening of snow and ice by black carbon deposition is a major factor for the rapid disappearance of arctic sea ice, mountain glaciers and snow packs. This study provides one of the first direct measurements for the efficient removal of black carbon from the atmosphere by snow and its subsequent deposition to the snow packs of California. The early melting of the snow packs in the Sierras is one of the contributing factors to the severe water problems in California. BC concentrations in falling snow were measured at two mountain locations and in rain at a coastal site. All three stations reveal large BC concentrations in precipitation, ranging from 1.7 ng/g to 12.9 ng/g. The BC concentrations in the air after the snow fall were negligible suggesting an extremely efficient removal of BC by snow. The data suggest that below cloud scavenging, rather than ice nuclei, was the dominant source of BC in the snow. A five-year comparison of BC, dust, and total fine aerosol mass concentrations at multiple sites reveals that the measurements made at the sampling sites were representative of large scale deposition in the Sierra Nevada. The relative concentration of iron and calcium in the mountain aerosol indicates that one-quarter to one-third of the BC may have been transported from Asia.

  20. Sulfonated carbon black-based composite membranes for fuel cell applications

    Indian Academy of Sciences (India)

    Hacer Doǧan; Emel Yildiz; Metin Kaya; Tülay Y Inan

    2013-08-01

    Two different commercial grade carbon black samples, Cabot Regal 400R (C1) and Cabot Mogul L (C2), were sulfonated with diazonium salt of sulfanilic acid. The resultant sulfonated carbon black samples (S–C) were characterized by Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis (TGA). Composite membranes were then prepared using S–C as fillers and sulfonated poly(ether ether ketone) (SPEEK) as polymer matrix with three different sulfonation degrees (DS = 60, 70 and 82%). Structure and properties of the composite membranes were characterized by FTIR, TGA, scanning electron microscopy, proton conduction, water uptake, ion exchange capacity and chemical stability. Incorporation of S–C particles above 0.25 wt% caused decrease in chemical stability. Pristine and composite membranes prepared from SPEEK82 decomposed completely in <1 h, which is undesirable for fuel cell applications. SPEEK60 membrane having wt% of 0.25–0.5 with S–C particles led to higher proton conductivity than that of pristine membrane. No positive effect was observed on the properties of the composite membranes with the addition of S–C particles at high concentrations due to the agglomeration problems and decrease in the content of conductive polymer matrix.

  1. Structural, mechanical and electrical characterization of epoxy-amine/carbon black nanonocomposites

    Directory of Open Access Journals (Sweden)

    2008-05-01

    Full Text Available This work presents an insight into the effect of preparation procedure and the filler content on both electrical and mechanical properties of a nanocomposite system. For the preparation of the nanocomposites diglycidyl ether of bisphenol A (DGEBA was used with triethylenetetramine (TETA as a curing agent. As fillers carbon black (CB nanoparticles with size from 25 to 75 nm were used. The characterization was done using Dynamic Mechanical Analysis (DMA, Dielectric Relaxation Spectroscopy (DRS, Differential Scanning Calorimetry (DSC, Wide Angle X-ray Diffraction (WAXD and electrical conductivity measurements. The dependence of the dynamic mechanical and dielectric parameters (E′, E″, tanδ, ε', ε″, σ and Tg is associated with the filler content and is controlled by the employed curing conditions. An increase in electrical conductivity, which is observed at about 1% w/w of carbon black, indicates the creation of conducting paths and is associated with the Maxwell Wagner Sillars (MWS relaxation, probably due to the formation of aggregated microstructures in the bulk composite..

  2. BLACK Carbon Emissions from Diesel Sources in the Largest Arctic City: Case Study of Murmansk

    Science.gov (United States)

    Evans, M.; Kholod, N.; Malyshev, V.; Tretyakova, S.; Gusev, E.; Yu, S.; Barinov, A.

    2014-12-01

    Russia has very little data on its black carbon (BC) emissions. Because Russia makes up such a large share of the Arctic, understanding Russian emissions will improve our understanding of overall BC levels, BC in the Arctic and the link between BC and climate change. This paper provides a detailed, bottom-up inventory of BC emissions from diesel sources in Murmansk, Russia, along with uncertainty estimates associated with these emissions. The research team developed a detailed data collection methodology. The methodology involves assessing the vehicle fleet and activity in Murmansk using traffic, parking lot and driver surveys combined with an existing database from a vehicle inspection station and statistical data. The team also assessed the most appropriate emission factors, drawing from both Russian and international inventory methodologies. The researchers also compared fuel consumption using statistical data and bottom-up fuel calculations. They then calculated emissions for on-road transportation, off-road transportation (including mines), diesel generators, fishing and other sources. The article also provides a preliminary assessment of Russia-wide emissions of black carbon from diesel sources.

  3. Nanocomposite electrodes made of carbon nanofibers and black wax. Anodic stripping voltammetry of zinc and lead.

    Science.gov (United States)

    van Dijk, N; Fletcher, S; Madden, C E; Marken, F

    2001-11-01

    Nanocomposite electrodes offer exciting new possibilities in electroanalytical chemistry. In this preliminary study, nanocomposite electrodes made of carbon nanofibers and black wax were characterized and investigated as novel substrates for metal deposition and stripping processes. Carbon nanofibers were grown from ethylene-hydrogen gas mixtures over Fe-Ni-Cu (85:10:5) nanoparticle catalysts at 600 degrees C and then embedded in Apiezon black wax under vacuum at 140 degrees C. The resulting nanocomposite electrodes showed (i) good conductivity, (ii) a wide potential window in aqueous solutions, (iii) low background currents, (iv) near steady state voltammetric responses with substantial Faradaic currents and (v) sharply peaked fast scan metal stripping responses. Zinc is a notoriously difficult metal to determine in aqueous solutions, because its deposition and stripping are accompanied by hydrogen evolution at extreme negative potentials. It therefore provided a challenging test for our new nanocomposite electrode. Although numerous complications associated with the hydrogen evolution process could not be eliminated, remarkably clear voltammograms could be obtained even at scan rates of 40 V s(-1).

  4. Sensitivity of Stratospheric Geoengineering with Black Carbon to Aerosol Size and Altitude of Injection

    Science.gov (United States)

    Kravitz, Ben; Robock, Alan; Shindell, Drew T.; Miller, Mark A.

    2012-01-01

    Simulations of stratospheric geoengineering with black carbon (BC) aerosols using a general circulation model with fixed sea surface temperatures show that the climate effects strongly depend on aerosol size and altitude of injection. 1 Tg BC/a injected into the lower stratosphere would cause little surface cooling for large radii but a large amount of surface cooling for small radii and stratospheric warming of over 60 C. With the exception of small particles, increasing the altitude of injection increases surface cooling and stratospheric warming. Stratospheric warming causes global ozone loss by up to 50% in the small radius case. The Antarctic shows less ozone loss due to reduction of polar stratospheric clouds, but strong circumpolar winds would enhance the Arctic ozone hole. Using diesel fuel to produce the aerosols is likely prohibitively expensive and infeasible. Although studying an absorbing aerosol is a useful counterpart to previous studies involving sulfate aerosols, black carbon geoengineering likely carries too many risks to make it a viable option for deployment.

  5. Optics of Water Cloud Droplets Mixed with Black-Carbon Aerosols

    Science.gov (United States)

    Mishchenko, Michael I.; Liu, Li; Cairns, Brian; Mackowski, Daniel W.

    2014-01-01

    We use the recently extended superposition T-matrix method to calculate scattering and absorption properties of micrometer-sized water droplets contaminated by black carbon. Our numerically exact results reveal that, depending on the mode of soot-water mixing, the soot specific absorption can vary by a factor exceeding 6.5. The specific absorption is maximized when the soot material is quasi-uniformly distributed throughout the droplet interior in the form of numerous small monomers. The range of mixing scenarios captured by our computations implies a wide range of remote sensing and radiation budget implications of the presence of black carbon in liquid-water clouds. We show that the popular Maxwell-Garnett effective-medium approximation can be used to calculate the optical cross sections, single-scattering albedo, and asymmetry parameter for the quasi-uniform mixing scenario, but is likely to fail in application to other mixing scenarios and in computations of the elements of the scattering matrix.

  6. High surface area carbon black (BP-2000) as a reinforcing agent for poly[(₋)-lactide

    Energy Technology Data Exchange (ETDEWEB)

    Delgado, Paula A.; Brutman, Jacob P.; Masica, Kristina; Molde, Joseph; Wood, Brandon; Hillmyer, Marc A. (UMM)

    2016-10-26

    We report that the brittle nature and low-heat distortion resistance of a promising biorenewable thermoplastics, poly((₋)-lactide) (PLA), motivate the investigation of strengthening additives that can address these deficiencies. Here in our work, a high surface area carbon black (BP-2000) as well as biobased carbon blacks (hydrochars) were examined as reinforcement agents for PLA. When 1–5 wt % BP-2000 was added to PLA, the crystallization of PLA was accelerated, resulting in higher crystallinity, tensile strength, and heat resistance. A thermal creep experiment revealed that the composites exhibited no significant deformation after 30 min with 2 N of uniaxial tensile force at 80°C (above the Tg), whereas neat PLA (with similar thermal history) elongated to 79% after 5 min under the same conditions. PLA–hydrochar composites demonstrated similar brittle behavior to neat PLA. Finally, despite the promising nucleating ability of hydrochars, they displayed low interfacial adhesion with PLA because of their low surface area, resulting in poor energy transfer on stretching

  7. Quantification of black carbon mixing state from traffic: implications for aerosol optical properties

    Science.gov (United States)

    Willis, Megan D.; Healy, Robert M.; Riemer, Nicole; West, Matthew; Wang, Jon M.; Jeong, Cheol-Heon; Wenger, John C.; Evans, Greg J.; Abbatt, Jonathan P. D.; Lee, Alex K. Y.

    2016-04-01

    The climatic impacts of black carbon (BC) aerosol, an important absorber of solar radiation in the atmosphere, remain poorly constrained and are intimately related to its particle-scale physical and chemical properties. Using particle-resolved modelling informed by quantitative measurements from a soot-particle aerosol mass spectrometer, we confirm that the mixing state (the distribution of co-emitted aerosol amongst fresh BC-containing particles) at the time of emission significantly affects BC-aerosol optical properties even after a day of atmospheric processing. Both single particle and ensemble aerosol mass spectrometry observations indicate that BC near the point of emission co-exists with hydrocarbon-like organic aerosol (HOA) in two distinct particle types: HOA-rich and BC-rich particles. The average mass fraction of black carbon in HOA-rich and BC-rich particle classes was < 0.1 and 0.8, respectively. Notably, approximately 90 % of BC mass resides in BC-rich particles. This new measurement capability provides quantitative insight into the physical and chemical nature of BC-containing particles and is used to drive a particle-resolved aerosol box model. Significant differences in calculated single scattering albedo (an increase of 0.1) arise from accurate treatment of initial particle mixing state as compared to the assumption of uniform aerosol composition at the point of BC injection into the atmosphere.

  8. Measured Black Carbon Deposition on the Sierra Nevada Snow Pack and Implication for Snow Pack Retreat

    Energy Technology Data Exchange (ETDEWEB)

    Hadley, O.L.; Corrigan, C.E.; Kirchstetter, T.W.; Cliff, S.S.; Ramanathan, V.

    2010-01-12

    Modeling studies show that the darkening of snow and ice by black carbon deposition is a major factor for the rapid disappearance of arctic sea ice, mountain glaciers and snow packs. This study provides one of the first direct measurements for the efficient removal of black carbon from the atmosphere by snow and its subsequent deposition to the snow packs of California. The early melting of the snow packs in the Sierras is one of the contributing factors to the severe water problems in California. BC concentrations in falling snow were measured at two mountain locations and in rain at a coastal site. All three stations reveal large BC concentrations in precipitation, ranging from 1.7 ng/g to 12.9 ng/g. The BC concentrations in the air after the snow fall were negligible suggesting an extremely efficient removal of BC by snow. The data suggest that below cloud scavenging, rather than ice nuclei, was the dominant source of BC in the snow. A five-year comparison of BC, dust, and total fine aerosol mass concentrations at multiple sites reveals that the measurements made at the sampling sites were representative of large scale deposition in the Sierra Nevada. The relative concentration of iron and calcium in the mountain aerosol indicates that one-quarter to one-third of the BC may have been transported from Asia.

  9. Stable carbon isotope analysis reveals widespread drought stress in boreal black spruce forests.

    Science.gov (United States)

    Walker, Xanthe J; Mack, Michelle C; Johnstone, Jill F

    2015-08-01

    Unprecedented rates of climate warming over the past century have resulted in increased forest stress and mortality worldwide. Decreased tree growth in association with increasing temperatures is generally accepted as a signal of temperature-induced drought stress. However, variations in tree growth alone do not reveal the physiological mechanisms behind recent changes in tree growth. Examining stable carbon isotope composition of tree rings in addition to tree growth can provide a secondary line of evidence for physiological drought stress. In this study, we examined patterns of black spruce growth and carbon isotopic composition in tree rings in response to climate warming and drying in the boreal forest of interior Alaska. We examined trees at three nested scales: landscape, toposequence, and a subsample of trees within the toposequence. At each scale, we studied the potential effects of differences in microclimate and moisture availability by sampling on northern and southern aspects. We found that black spruce radial growth responded negatively to monthly metrics of temperature at all examined scales, and we examined ∆(13)C responses on a subsample of trees as representative of the wider region. The negative ∆(13)C responses to temperature reveal that black spruce trees are experiencing moisture stress on both northern and southern aspects. Contrary to our expectations, ∆(13)C from trees on the northern aspect exhibited the strongest drought signal. Our results highlight the prominence of drought stress in the boreal forest of interior Alaska. We conclude that if temperatures continue to warm, we can expect drought-induced productivity declines across large regions of the boreal forest, even for trees located in cool and moist landscape positions. © 2015 John Wiley & Sons Ltd.

  10. Utilization of the Net Heat Process Tail Gases in the Reactor for the Production of Oil-Furnace Carbon Black

    Directory of Open Access Journals (Sweden)

    Bosak, Z.

    2011-02-01

    Full Text Available Tail gases of low calorific value, which are the by-product of oil-furnace carbon black industrial production, can be efficiently used as energy before their final release into the atmosphere. Apart from being used mainly for heating dryers, production of steam, electricity, or flared, they can also be used as a substitute for fuel in the reactor for the production of oil-furnace carbon blacks, thus increasing the efficiency of the hydrocarbon raw feedstock.This technical paper represents the technical-technological solution for applying the waste heat of the low calorific tail gases in the reactor for the production of "hard" grade oil-furnace carbon blacks with savings of the hydrocarbon raw feedstock.The introduction of the preheated low calorific tail gases in the reactor for the production of "hard" grade oil-furnace carbon blacks is achieved by serial cascading of four fans. The system consists of fans designed to pneumatically transport the mixture of process tail gases and oil-furnace carbon black dust particles. This ensures a stable technological process for the introduction of the low calorific process tail gases into the reaction zone where the natural gas and preheated air are combusted.In the production of oil-furnace carbon black N220, it is shown that by using low calorific process tail gases in the amount from 1000 to 2000 m3 h–1 per reactor, savings from 10 to 20 % of natural gas and simultaneously 7 to 9 % of the hydrocarbon raw feedstoks were achieved.

  11. Chemical analysis and molecular models for calcium-oxygen-carbon interactions in black carbon found in fertile Amazonian anthrosoils.

    Science.gov (United States)

    Archanjo, Braulio S; Araujo, Joyce R; Silva, Alexander M; Capaz, Rodrigo B; Falcão, Newton P S; Jorio, Ado; Achete, Carlos A

    2014-07-01

    Carbon particles containing mineral matter promote soil fertility, helping it to overcome the rather unfavorable climate conditions of the humid tropics. Intriguing examples are the Amazonian Dark Earths, anthropogenic soils also known as "Terra Preta de Índio'' (TPI), in which chemical recalcitrance and stable carbon with millenary mean residence times have been observed. Recently, the presence of calcium and oxygen within TPI-carbon nanoparticles at the nano- and mesoscale ranges has been demonstrated. In this work, we combine density functional theory calculations, scanning transmission electron microscopy, energy dispersive X-ray spectroscopy, Fourier transformed infrared spectroscopy, and high resolution X-ray photoelectron spectroscopy of TPI-carbons to elucidate the chemical arrangements of calcium-oxygen-carbon groups at the molecular level in TPI. The molecular models are based on graphene oxide nanostructures in which calcium cations are strongly adsorbed at the oxide sites. The application of material science techniques to the field of soil science facilitates a new level of understanding, providing insights into the structure and functionality of recalcitrant carbon in soil and its implications for food production and climate change.

  12. Black Carbon And Co-Pollutants Emissions And Energy Efficiency From Bricks Production In Guanajuato, Mexico

    Science.gov (United States)

    Molina, L. T.; Zavala, M.; Maiz, P.; Monsivais, I.; Chow, J.; Munguia, J.

    2013-12-01

    In many parts of the world, small-scale traditional brick kilns are a notorious informal sector source of urban air pollution. Many are both inefficient and burn highly polluting fuels that emit significant levels of black carbon and other pollutants into local communities and to the atmosphere, resulting in severe health and environmental impacts. It is estimated that there are nearly 20,000 traditional brick kilns in Mexico, in which bricks are still produced as they have been for centuries. They are made by hand, dried in the sun, and generally fired in small, one chamber kilns that use various types of fuels, including plastic refuse, used tires, manure, wood scrap, and used motor oil. Three brick kilns, two traditional kilns and an improved kiln (MK2), were sampled as part of the SLCFs-Mexico campaign in Guanajuato, Mexico during March of 2013. The concept of the MK-2 involves covering the kiln with a dome and channeling the output of an active kiln through a second, identical loaded kiln for its additional filtration of the effluents. The results of energy efficiency and carbon mass balance calculations are presented for comparing the production efficiency and carbon emissions from the sampled kilns. Measurements included PM2.5 mass with quartz filters and temporally-resolved elemental carbon and organic carbon composition obtained using thermo-optical methods. The carbon emissions obtained with the mass balance method are compared with concurrent, high- time resolution, emissions measurements obtained using the Aerodyne mobile laboratory employing the tracer method (see abstract by Fortner et al.)

  13. Black carbon and other refractory forms in recent sediments from the Gulf of Cadiz, Spain

    Science.gov (United States)

    González-Vila, F. J.; de la Rosa, J. M.; González-Pérez, J. A.

    2009-01-01

    Black carbon (BC) produced by incomplete combustion of fossil fuels and vegetation is a ubiquitous form of refractory organic matter (ROM) widely distributed in the environment. The stable non-reactive, mainly aromatic, BC has received special interest in recent years as a possible carbon sink in soils and sediments. At present, several methods have been used, with applications for soil and sediments, although no single method has been accepted to detect BC forms, and therefore providing the analytical data required to estimate BC contribution to terrestrial and sedimentary carbon fluxes and the global carbon cycle. This study considers the potential of the combined use of analytical pyrolysis (Py-GC/MS) and solid state 13C NMR to determine the presence of BC and to characterize the refractory organic matter in a set of recent marine sediments from the Southwest Atlantic coast of Spain (Gulf of Cadiz). The content of BC-like material found in sediments (3.0 - 16.5 % of total organic carbon) was in the range previously reported for this kind of samples and decreases from coast to offshore. Solid state CP-MAS 13C NMR and Py-GC/MS analysis of the isolated ROM revealed a conspicuous aliphatic domain remained in the samples after chlorite oxidation. Our results suggests that, in recent sediments from fluvial and marine environments, not only BC and refractory carbon forms with aromatic nature may be sequestered in a stable form; it also seems probable that the ROM pool contains a significant amount of C immobilized in the form of alkylic compounds.

  14. End of the "Little Ice Age" in the Alps not forced by industrial black carbon

    Science.gov (United States)

    Sigl, Michael; Osmont, Dimtri; Gabrieli, Jacopo; Barbante, Carlo; Schwikowski, Margit

    2016-04-01

    Light absorbing aerosols present in the atmosphere and cryosphere play an important role in the climate system. Their presence in ambient air and snow changes radiative properties of these media, thus contributing to increased atmospheric warming and snowmelt. High spatio-temporal variability of aerosol concentrations in these media and a shortage of long-term observations contribute to large uncertainties in properly assigning the climate effects of these aerosols through time. Glaciers in the European Alps began to retreat abruptly from their mid-19th century maximum, marking what appeared to be the end of the Little Ice Age. Radiative forcing by increasing deposition of industrial black carbon to snow has been suggested as the main driver of the abrupt glacier retreats in the Alps (Painter et al. 2012). Basis for this hypothesis were model simulations using ice-core measurements of elemental carbon at low temporal resolution from two ice cores in the Alps. Here we present sub-annually resolved, well replicated ice-core measurements of refractory black carbon (rBC; using a SP2 soot photometer), mineral dust (Fe, Ca), biomass burning (NH4, K) and distinctive industrial pollution tracers (Bi, Pb, SO4) from an ice core in the Alps covering the past 250 years. These reconstructions allow to precisely compare the timing of observed acceleration of glacier melt in the mid-19th century with that of the increase of soot deposition on ice-sheets caused by the industrialization of Western Europe. Our study suggests that at the time when European rBC emission rates started to significantly increase Alpine glaciers have already experienced more than 70% of their total 19th century length reduction. Industrial BC emissions can therefore not been considered as the primary forcing of the rapid deglaciation at the end of the Little Ice Age in the Alps. References: Painter, T. H., M. G. Flanner, G. Kaser, B. Marzeion, R. A. VanCuren, and W. Abdalati (2013), End of the Little Ice

  15. North-South Gradients in Carbon Isotopic Compositions of Atlantic Ocean Black Shales: Evidence for Paleohydrologic Influences on Mid-Cretaceous Black Shale Deposition

    Science.gov (United States)

    Meyers, P. A.

    2013-12-01

    Organic del13C values of organic-carbon-rich Albian-Cenomanian-Turonian black shales from a north-south transect of the Atlantic Ocean have been compiled to explore for possible existence of latitudinal patterns. Black shales at equatorial sites have mean del13C values of -28 per mil, whereas black shales at mid-latitude sites have mean del13C values around -25 per mil. The mid-Cretaceous del13C values are routinely lower than those of modern marine sediments. The more negative Cretaceous del13C values generally reflect concentrations of atmospheric CO2 that were four to six times higher than today, but the geographic differences imply a regional overprint on this global feature. Latitudinal differences in oceanic temperature might be a factor, but a low thermal gradient from the poles to the equator during the mid-Cretaceous makes this factor not likely to be significant. Instead, a correspondence between the geographic differences in the organic del13C values of black shales with the modern latitudinal precipitation pattern suggests that differences in precipitation are a more likely factor. Establishment of a strongly salinity-stratified near-surface ocean and magnified delivery of land-derived phosphorus by continental runoff during this time of a magnified hydrologic cycle were evidently significant to deposition of marine black shales. A likely scenario is that the stratification resulted in blooms of nitrogen-fixing bacteria that become the dominant photoautotrophs and thereby stimulated primary production of organic matter. Regional differences in precipitation resulted in different amounts of runoff, consequent stratification, enhancement of primary production, and therefore the different carbon isotopic compositions of the black shales.

  16. Variability in and agreement between modeled and personal continuously measured black carbon levels using novel smartphone and sensor technologies.

    Science.gov (United States)

    Nieuwenhuijsen, Mark J; Donaire-Gonzalez, David; Rivas, Ioar; de Castro, Montserrat; Cirach, Marta; Hoek, Gerard; Seto, Edmund; Jerrett, Michael; Sunyer, Jordi

    2015-03-01

    Novel technologies, such as smartphones and small personal continuous air pollution sensors, can now facilitate better personal estimates of air pollution in relation to location. Such information can provide us with a better understanding about whether and how personal exposures relate to residential air pollution estimates, which are normally used in epidemiological studies. The aims of this study were to examine (1) the variability in personal air pollution levels during the day and (2) the relationship between modeled home and school estimates and continuously measured personal air pollution exposure levels in different microenvironments (e.g., home, school, and commute). We focused on black carbon as an indicator of traffic-related air pollution. We recruited 54 school children (aged 7-11) from 29 different schools around Barcelona as part of the BREATHE study, an epidemiological study of the relation between air pollution and brain development. For 2 typical week days during 2012-2013, the children were given a smartphone with CalFit software to obtain information on their location and physical activity level and a small sensor, the micro-aethalometer model AE51, to measure their black carbon levels simultaneously and continuously. We estimated their home and school exposure to PM2.5 filter absorbance, which is well-correlated with black carbon, using a temporally adjusted PM2.5 absorbance land use regression (LUR) model. We found considerable variation in the black carbon levels during the day, with the highest levels measured during commuting periods (geometric mean = 2.8 μg/m(3)) and the lowest levels at home (geometric mean = 1.3 μg/m(3)). Hourly temporally adjusted LUR model estimates for the home and school showed moderate to good correlation with measured personal black carbon levels at home and school (r = 0.59 and 0.68, respectively) and lower correlation with commuting trips (r = 0.32 and 0.21, respectively). The correlation between modeled home

  17. The Effects of Silica/Carbon Black Ratio on the Dynamic Properties of the Tread compounds in Truck Tires

    Directory of Open Access Journals (Sweden)

    Ramin Zafarmehrabian

    2012-01-01

    Full Text Available NR is the major constituent in the rubber compound used for the tread on the truck tires. A general compound formulation of the tire tread includes NR and BR as polymer base and carbon black as the reinforcing filler, and curative components. In this paper the effects of dual filler system (carbon black and precipitated silica on the dynamic properties of tire treat has been studied. The results show by increasing of precipitated silica, significant improvement was observed in fatigue resistance, rolling resistance and heat buildup of the tire. Tensile strength and modulus and wet grip of tire tread decrease with increasing of silica in rubber compound formulation.

  18. Modified thermal-optical analysis using spectral absorption selectivity to distinguish black carbon from pyrolized organic carbon

    Energy Technology Data Exchange (ETDEWEB)

    Hadley, Odelle; Hadley, O.L.; Corrigan, C.E.; Kirchstetter, T.W.

    2008-04-14

    Black carbon (BC), a main component of combustion-generated soot, is a strong absorber of sunlight and contributes to climate change. Measurement methods for BC are uncertain, however. This study presents a method for analyzing the BC mass loading on a quartz fiber filter using a modified thermal-optical analysis method, wherein light transmitted through the sample is measured over a spectral region instead of at a single wavelength as the sample is heated. Evolution of the spectral light transmission signal depends on the relative amounts of light-absorbing BC and char, the latter of which forms when organic carbon in the sample pyrolyzes during heating. Absorption selectivities of BC and char are found to be distinct and are used to apportion the amount of light attenuated by each component in the sample. Light attenuation is converted to mass concentration based on derived mass attenuation efficiencies (MAE) of BC and char. The fraction of attenuation due to each component are scaled by their individual MAE values and added together as the total mass of light absorbing carbon (LAC). An iterative algorithm is used to find the MAE values for both BC and char that provide the best fit to the carbon mass remaining on the filter (derived from direct measurements of thermally evolved CO{sub 2}) at temperatures higher than 480 C. This method was applied to measure the BC concentration in precipitation samples collected from coastal and mountain sites in Northern California. The uncertainty in measured BC concentration of samples that contained a high concentration of organics susceptible to char ranged from 12 to 100 percent, depending on the mass loading of BC on the filter. The lower detection limit for this method was approximately 0.35 {micro}g BC and uncertainty approached 20 percent for BC mass loading greater than 1.0 {micro}g BC.

  19. Black carbon emissions from in-use ships: a California regional assessment

    Directory of Open Access Journals (Sweden)

    G. M. Buffaloe

    2013-09-01

    Full Text Available Black carbon (BC mass emission factors (EFBC; g-BC (kg-fuel−1 from a variety of ocean going vessels have been determined from measurements of BC and carbon dioxide (CO2 concentrations in ship plumes intercepted by the R/V Atlantis during the 2010 California Nexus (CalNex campaign. The ships encountered were all operating within 24 nautical miles of the California coast and were utilizing relatively low sulphur fuels. Black carbon concentrations within the plumes, from which EFBC values are determined, were measured using four independent instruments: a photoacoustic spectrometer and a particle soot absorption photometer, which measure light absorption, and a single particle soot photometer and soot particle aerosol mass spectrometer, which measure the mass concentration of refractory BC directly. The measured EFBC have been divided into vessel type categories and engine type categories, from which averages have been determined. The geometric average EFBC, determined from over 71 vessels and 135 plumes encountered, was 0.31 g-BC (kg-fuel−1. The most frequent engine type encountered was the slow speed diesel (SSD, and the most frequent SSD vessel type was the cargo ship sub-category. Average and median EFBC values from the SSD category are compared with previous observations from the Texas Air Quality Study (TexAQS in 2006, during which the ships encountered were predominately operating on high sulphur fuels. There is a statistically significant difference between the EFBC values from CalNex and TexAQS for SSD vessels and for the cargo and tanker ship types within this engine category. The CalNex EFBC values are lower than those from TexAQS, suggesting that operation on lower sulphur fuels is associated with smaller EFBC values.

  20. Comparison of PAN and Black Carbon Levels in Mexico City: 1997 and 2003

    Science.gov (United States)

    Gaffney, J. S.; Marley, N. A.

    2004-12-01

    Peroxyacetyl nitrate (PAN) is a secondary oxidant formed by the oxidation of hydrocarbons in the presence of nitrogen dioxide. PAN is a good indicator compound for hydrocarbon reactivity that leads to ozone formation. Black carbon (BC) is formed by incomplete combustion processes such as diesel soot formation and is a good indicator of primary carbonaceous aerosols in urban areas. We used a fast-response luminol method to measure PAN and BC during the Mexico City Metropolitan Area 2003/Mexico City Megacity 2003 field study in April 2003. We compare these results with our previous PAN measurements in Mexico City during February 1997, made with a gas chromatograph-electron capture detector system. The decreased PAN levels observed in 2003 are consistent with the application of emissions controls on spark ignition gasoline-fueled vehicles, leading to lower levels of the nitrogen oxides and reactive volatile hydrocarbons needed to form PAN. Black carbon data for Mexico City in 2003, taken with a seven-channel aethalometer, are compared with data from 1997, estimated from thermal analyses as elemental carbon (EC). The comparison indicates little change in the levels of BC/EC over the six-year period. This observation is consistent with the application of minimal controls to diesel engines, the likely major source of BC in the Mexico City megacity complex during this period. The authors wish to thank the researchers at Centro Nacional de Investigación en Calidad Ambiental (CENICA), Mexico City. This work was supported by the U.S. Department of Energy, Atmospheric Science Program. We also wish to acknowledge Drs. Mario and Luisa Molina for their help in organizing and directing the Mexico City Metropolitan Area 2003 field study, during which these data were collected.

  1. Two black carbon pools transported by the Changjiang and Huanghe Rivers in China

    Science.gov (United States)

    Wang, Xuchen; Xu, Caili; Druffel, Ellen M.; Xue, Yuejun; Qi, Yuanzhi

    2016-12-01

    Major rivers play important roles in transporting large amounts of terrestrial organic matter from land to the ocean each year, and the organic matter carried by rivers contains a significant fraction of black carbon (BC). A recent study estimated that 0.027 Gt of BC is transported in the dissolved phase by rivers each year, which accounts for 10% of the global flux of dissolved organic carbon. The relative sources of this large amount of riverine dissolved black carbon (DBC) from biomass burning (young, modern 14C) and fossil fuel (old, 14C free) combustion are not known. We present radiocarbon measurements of BC in both dissolved and particulate phases transported by the Changjiang and Huanghe Rivers, the two largest rivers in China, during 2015. We show that two, distinct BC pools (young and old) were carried by the rivers. The DBC pool was much younger than the particulate BC (PBC) pool. Mass balance calculations indicate that most (78-85%) of the DBC in the Changjiang and Huanghe Rivers was derived from biomass burning, and only 15-22% was from fossil fuel combustion. In contrast, PBC from biomass burning and fossil fuel combustion were approximately equal in these two rivers. Export of PBC and DBC by the rivers are decoupled, and fluxes of PBC were 4.1 and 6.7 times higher than DBC in the Changjiang and Huanghe Rivers, respectively. The 14C age differences of the two BC pools suggest that BC derived from biomass burning and fossil fuel combustion are mobilized in different phases and on different time scales in these rivers.

  2. Dissolved Black Carbon in the Southern Ocean along CLIVAR section I6S

    Science.gov (United States)

    Paeng, J.; Dittmar, T.

    2008-12-01

    Thermogenic matter ("black carbon", BC) is abundant in the environment. BC is produced during catagenesis in earth's crust and is also a residue of fossil fuel and biomass burning. Because of its refractory character, BC accumulates in soils and sediments and sequesters carbon from active cycles. Previous studies found indications that BC might be a significant component also in marine dissolved organic matter (DOM). However, the available information on black carbon in DOM is extremely rare up to now. The objective of this study is to quantify BC in marine DOM and identify the source and dynamics of dissolved BC for a major oceanic region. Detailed depth profiles were sampled along 30º E from South Africa to Antarctica at 1º intervals on CLIVAR section I6S. Dissolved BC was isolated from approximately 250 seawater samples via a new solid phase extraction method. Fused aromatic ring systems as a molecular tracer for BC were quantified in these samples. For this purpose, the samples were oxidized with nitric acid and the reaction products of fused ring systems analyzed as benzene-polycarboxylic acids with HPLC. BC concentrations were very stable throughout the water column and along the North-South section, ranging between 500 and 700 nM BC. The molecular composition of benzene-polycarboxylic acids indicates a relatively small number of fused aromatic rings per molecule. Similar structures were observed preciously in riverine and also petroleum-derived DOM. The homogenous distribution of BC in all water masses indicates conservative behavior of BC in the ocean, and turnover rates which are far longer than oceanic turnover rates. The stable character of dissolved BC and its abundance in the ocean has major implications for our understanding of global biogeochemical cycles.

  3. Black carbon contributes to organic matter in young soils in the Morteratsch proglacial area (Switzerland

    Directory of Open Access Journals (Sweden)

    E. Eckmeier

    2013-03-01

    Full Text Available Most glacier forefields of the European Alps are being progressively exposed since the glaciers reached their maximum expansion in the 1850s. Global warming and climate changes additionally promote the exposure of sediments in previously glaciated areas. In these proglacial areas, initial soils have started to develop so that they may offer a continuous chronosequence from 0 to 150-yr-old soils. The build-up of organic matter is an important factor of soil formation, and not only autochthonous but also distant sources might contribute to its accumulation in young soils and surfaces of glacier forefields. Only little is known about black carbon in soils that develop in glacier forefields, although charred organic matter could be an important component of organic carbon in Alpine soils. The aim of our study was to examine whether black carbon (BC is present in the initial soils of a proglacial area, and to estimate its relative contribution to soil organic matter. We investigated soil samples from 35 sites distributed over the whole proglacial area of Morteratsch (Upper Engadine, Switzerland, covering a chronosequence from 0 to 150 yr. BC concentrations were determined in fine earth using the benzene polycarboxylic acid (BPCA marker method. We found that charred organic matter occurred in the whole area, and that it was a main compound of soil organic matter in the youngest soils, where total Corg concentrations were very low. The absolute concentrations of BC in fine earth were generally low but increased in soils that had been exposed for more than 40 yr. Specific initial microbial communities may profit from this additional C source during the first years of soil evolution and potentially promote soil development in its early stage.

  4. Black (pyrogenic) carbon: a synthesis of current knowledge and uncertainties with special consideration of boreal regions

    Science.gov (United States)

    Preston, C. M.; Schmidt, M. W. I.

    2006-09-01

    The carbon (C) cycle in boreal regions is strongly influenced by fire, which converts biomass and detrital C mainly to gaseous forms (CO2 and smaller proportions of CO and CH4), and some 1-3% of mass to pyrogenic C (PyC). PyC is mainly produced as solid charred residues, including visually-defined charcoal, and a black carbon (BC) fraction chemically defined by its resistance to laboratory oxidation, plus much lower proportions of volatile soot and polycyclic aromatic hydrocarbons (PAHs). All PyC is characterized by fused aromatic rings, but varying in cluster sizes, and presence of other elements (N, O) and functional groups. The range of PyC structures is often described as a continuum from partially charred plant materials, to charcoal, soot and ultimately graphite which is formed by the combination of heat and pressure. There are several reasons for current interest in defining more precisely the role of PyC in the C cycle of boreal regions. First, PyC is largely resistant to decomposition, and therefore contributes to very stable C pools in soils and sediments. Second, it influences soil processes, mainly through its sorption properties and cation exchange capacity, and third, soot aerosols absorb solar radiation and may contribute to global warming. However, there are large gaps in the basic information needed to address these topics. While charcoal is commonly defined by visual criteria, analytical methods for BC are mainly based on various measures of oxidation resistance, or on yield of benzenepolycarboxylic acids. These methods are still being developed, and capture different fractions of the PyC structural continuum. There are few quantitative reports of PyC production and stocks in boreal forests (essentially none for boreal peatlands), and results are difficult to compare due to varying experimental goals and methods, as well as inconsistent terminology. There are almost no direct field measurements of BC aerosol production from boreal wildfires, and

  5. Black (pyrogenic carbon: a synthesis of current knowledge and uncertainties with special consideration of boreal regions

    Directory of Open Access Journals (Sweden)

    C. M. Preston

    2006-01-01

    Full Text Available The carbon (C cycle in boreal regions is strongly influenced by fire, which converts biomass and detrital C mainly to gaseous forms (CO2 and smaller proportions of CO and CH4, and some 1–3% of mass to pyrogenic C (PyC. PyC is mainly produced as solid charred residues, including visually-defined charcoal, and a black carbon (BC fraction chemically defined by its resistance to laboratory oxidation, plus much lower proportions of volatile soot and polycyclic aromatic hydrocarbons (PAHs. All PyC is characterized by fused aromatic rings, but varying in cluster sizes, and presence of other elements (N, O and functional groups. The range of PyC structures is often described as a continuum from partially charred plant materials, to charcoal, soot and ultimately graphite which is formed by the combination of heat and pressure. There are several reasons for current interest in defining more precisely the role of PyC in the C cycle of boreal regions. First, PyC is largely resistant to decomposition, and therefore contributes to very stable C pools in soils and sediments. Second, it influences soil processes, mainly through its sorption properties and cation exchange capacity, and third, soot aerosols absorb solar radiation and may contribute to global warming. However, there are large gaps in the basic information needed to address these topics. While charcoal is commonly defined by visual criteria, analytical methods for BC are mainly based on various measures of oxidation resistance, or on yield of benzenepolycarboxylic acids. These methods are still being developed, and capture different fractions of the PyC structural continuum. There are few quantitative reports of PyC production and stocks in boreal forests (essentially none for boreal peatlands, and results are difficult to compare due to varying experimental goals and methods, as well as inconsistent terminology. There are almost no direct field measurements of BC aerosol production from boreal

  6. Black (pyrogenic carbon in boreal forests: a synthesis of current knowledge and uncertainties

    Directory of Open Access Journals (Sweden)

    C. M. Preston

    2006-02-01

    Full Text Available The carbon (C cycle in boreal regions is strongly influenced by fire, which converts biomass and detrital C mainly to gaseous forms (CO2 and smaller proportions of CO and CH4, and some 1–7% of mass to pyrogenic C (PyC. PyC is mainly produced as solid charred residues, including visually-defined charcoal, and a black carbon (BC fraction chemically defined by its resistance to laboratory oxidation, plus much lower proportions of volatile soot and polycyclic aromatic hydrocarbons (PAHs. All PyC is characterized by fused aromatic rings, but varying in cluster sizes, and presence of other elements (N, O and functional groups. There are several reasons for current interest in defining more precisely the role of PyC in the C cycle of boreal regions. First, PyC is resistant to decomposition, and therefore contributes to very stable C pools in soils and sediments. Second, it influences soil processes, mainly through its sorption properties and cation exchange capacity, and third, soot aerosols absorb solar radiation and may contribute to global warming. However, there are large gaps in the basic information needed to address these topics. While charcoal is commonly defined by visual criteria, analytical methods for BC are mainly based on various measures of oxidation resistance, or on yield of benzenepolycarboxylic acids. These methods are still being developed, and capture different fractions of the PyC "continuum". There are few quantitative reports of PyC production and stocks in boreal forests (essentially none for boreal peatlands, and results are difficult to compare due to varying experimental goals and methods, as well as inconsistent terminology. There are almost no direct field measurements of BC aerosol production from boreal wildfires, and little direct information on rates and mechanisms for PyC loss. Structural characterization of charred biomass and forest floor from wildfires generally indicates a low level of

  7. Street characteristics and traffic factors determining road users' exposure to black carbon

    Energy Technology Data Exchange (ETDEWEB)

    Dons, Evi, E-mail: evi.dons@vito.be [VITO (Flemish Institute for Technological Research), Boeretang 200, 2400 Mol (Belgium); IMOB (Transportation Research Institute), Hasselt University, Wetenschapspark 5 bus 6, 3590 Diepenbeek (Belgium); Temmerman, Philip [IMOB (Transportation Research Institute), Hasselt University, Wetenschapspark 5 bus 6, 3590 Diepenbeek (Belgium); Van Poppel, Martine [VITO (Flemish Institute for Technological Research), Boeretang 200, 2400 Mol (Belgium); Bellemans, Tom; Wets, Geert [IMOB (Transportation Research Institute), Hasselt University, Wetenschapspark 5 bus 6, 3590 Diepenbeek (Belgium); Int Panis, Luc [VITO (Flemish Institute for Technological Research), Boeretang 200, 2400 Mol (Belgium); IMOB (Transportation Research Institute), Hasselt University, Wetenschapspark 5 bus 6, 3590 Diepenbeek (Belgium)

    2013-03-01

    Many studies nowadays make the effort of determining personal exposure rather than estimating exposure at the residential address only. While intra-urban air pollution can be modeled quite easily using interpolation methods, estimating exposure in transport is more challenging. The aim of this study is to investigate which factors determine black carbon (BC) concentrations in transport microenvironments. Therefore personal exposure measurements are carried out using portable aethalometers, trip diaries and GPS devices. More than 1500 trips, both by active modes and by motorized transport, are evaluated in Flanders, Belgium. GPS coordinates are assigned to road segments to allow BC concentrations to be linked with trip and road characteristics (trip duration, degree of urbanization, road type, traffic intensity, travel speed and road speed). Average BC concentrations on highways (10.7 μg/m{sup 3}) are comparable to concentrations on urban roads (9.6 μg/m{sup 3}), but levels are significantly higher than concentrations on rural roads (6.1 μg/m{sup 3}). Highways yield higher BC exposures for motorists compared to exposure on major roads and local roads. Overall BC concentrations are elevated at lower speeds (< 30 km/h) and at speeds above 80 km/h, in accordance to vehicle emission functions. Driving on roads with low traffic intensities resulted in lower exposures than driving on roads with higher traffic intensities (from 5.6 μg/m{sup 3} for roads with less than 500 veh/h, up to 12 μg/m{sup 3} for roads with over 2500 veh/h). Traffic intensity proved to be the major explanatory variable for in-vehicle BC exposure, together with timing of the trip and urbanization. For cyclists and pedestrians the range in BC exposure is smaller and models are less predictive; for active modes exposure seems to be influenced by timing and degree of urbanization only. - Highlights: ► Aethalometers, an electronic diary and GPS were used to measure exposure in transport ► More

  8. Black Carbon Particle Number Distribution Measurements during the ATHENS-2013 Winter Campaign

    Science.gov (United States)

    Gkatzelis, Georgios; Papanastasiou, Dimitris; Florou, Kalliopi; Kaltsonoudis, Christos; Louvaris, Eyaggelos; Bezentakos, Spiridon; Biskos, Georgios; Pandis, Spuros

    2014-05-01

    Black Carbon (BC) particles emitted by anthropogenic sources play an important role both in climate change and in air quality degradation. Open burning in forests and savannas, combustion of diesel and solid fuels for cooking and heating in homes represent the majority of BC emissions. Earlier work has focused on the BC atmospheric direct radiative forcing that is mostly related to its mass concentration and optical properties of the corresponding particles. A variety of measurement techniques are used to measure the mass concentration of BC by taking advantage of its optical or physical properties. Moreover, the carbonaceous particles containing BC are also important for the indirect forcing of climate. This effect is mostly related to the number concentration of BC particles. The number distribution of BC particles especially below 100 nm is quite uncertain due to limitations of the existing measurement techniques. In this work we employed a thermodenuder-based method as an approach for the measurement of the BC number distribution. More specifically, we combined a thermodenuder (TD) operating at temperatures up to 300 ° C, with a Scanning Mobility Particle Sizer (SMPS) and a High Resolution Time of Flight Aerosol Mass Spectrometer (HR-ToF AMS). Aerosol size and composition measurements were carried out both at ambient and at elevated TD temperatures in Athens field campaign during January and February of 2013. In parallel, a Multi-Angle Absorption Photometer (MAAP) provided information about the BC mass concentration while a Hygroscopic Tandem Differential Mobility Analyzer (HTDMA) measured the mixing state and the hygroscopicity of the particles as a function of their size. These measurements were then combined to estimate the number concentration of BC particles. Our analysis focused on different periods during the study. During some of them one source dominated the carbonaceous aerosol concentration. Such periods included rush hour traffic, nighttime wood

  9. Probing Photosensitization by Functionalized Carbon Nanotubes

    Science.gov (United States)

    Carbon nanotubes (CNTs) photosensitize the production of reactive oxygen species that can damage organisms by biomembrane oxidation or mediate CNTs' environmental transformations. The photosensitized nature of derivatized carbon nanotubes from various synthetic methods, and thus ...

  10. Eddington-limited accretion and the black hole mass function at redshift 6

    CERN Document Server

    Willott, Chris J; Arzoumanian, Doris; Bergeron, Jacqueline; Crampton, David; Delorme, Philippe; Hutchings, John B; Omont, Alain; Reyle, Celine; Schade, David

    2010-01-01

    We present discovery observations of a quasar in the Canada-France High-z Quasar Survey (CFHQS) at redshift z=6.44. We also use near-IR spectroscopy of nine CFHQS quasars at z~6 to determine black hole masses. These are compared with similar estimates for more luminous Sloan Digital Sky Survey (SDSS) quasars to investigate the relationship between black hole mass and quasar luminosity. We find a strong correlation between MgII FWHM and UV luminosity and that most quasars at this early epoch are accreting close to the Eddington limit. Thus these quasars appear to be in an early stage of their life cycle where they are building up their black hole mass exponentially. Combining these results with the quasar luminosity function, we derive the black hole mass function at z=6. Our black hole mass function is ~10^4 times lower than at z=0 and substantially below estimates from previous studies. The main uncertainties which could increase the black hole mass function are a larger population of obscured quasars at hig...

  11. Proton transfer reactions in carbon nanotubes endohedrally functionalized with selected polar amino acid sidechains

    Energy Technology Data Exchange (ETDEWEB)

    Abi, T.G. [Department of Chemistry, Indian Institute of Technology, Kharagpur 721302 (India); Taraphder, Srabani, E-mail: srabani@chem.iitkgp.ernet.in [Department of Chemistry, Indian Institute of Technology, Kharagpur 721302 (India)

    2012-09-11

    Graphical abstract: Free Energies of activation and reaction for intramolecular proton transfer between polar amino acid sidechains and hydroxyl groups inside the core of endohedrally functionalized single walled carbon nanotubes. Highlights: Black-Right-Pointing-Pointer EVB based free energy simulation of proton transfer in hydrophobic confinement. Black-Right-Pointing-Pointer Aminoacid sidechain and OH group suspended within carbon nanotube act as reactants. Black-Right-Pointing-Pointer Donors like His and Glu are efficient in confinement aided by local hydrogen bonds. -- Abstract: We use the empirical-valence-bond (EVB) theory to investigate intramolecular proton transfer reactions between a selected set of polar amino acid sidechains and hydroxyl groups suspended inside carbon nanotubes to model the effect of hydrophobic confinement on the energetics of proton transfer involving (i) translocation of an excess protonic charge (with protonated histidine sidechain as donor) and (ii) transformation of a neutral reactant state to a charge-separated product state (with sidechains of Asp, Glu, Ser and Thr as donor). In both the cases, confinement in hydrophobic medium is found to change the associated free energies compared to their respective values in the bulk solution phase. Presence of stable hydrogen bonding within the pore is found to have a significant effect on both free energies of reaction and activation and thus governs the thermodynamic and kinetic feasibilities of these intramolecular reactions in hydrophobic confinement.

  12. Influence of the Synthesis Method for Pt Catalysts Supported on Highly Mesoporous Carbon Xerogel and Vulcan Carbon Black on the Electro-Oxidation of Methanol

    OpenAIRE

    2015-01-01

    Platinum catalysts supported on carbon xerogel and carbon black (Vulcan) were synthesized with the aim of investigating the influence of the characteristics of the support on the electrochemical performance of the catalysts. Three synthesis methods were compared: an impregnation method with two different reducing agents, sodium borohydride and formic acid, and a microemulsion method, in order to study the effect of the synthesis method on the physico-chemical properties of the catalysts. X-ra...

  13. Area functional relation for 5D-Gauss-Bonnet-AdS black hole

    Science.gov (United States)

    Pradhan, Parthapratim

    2016-08-01

    We present area (or entropy) functional relation for multi-horizons five dimensional (5D) Einstein-Maxwell-Gauss-Bonnet-AdS black hole. It has been observed by exact and explicit calculation that some complicated function of two or three horizons area is mass-independent whereas the entropy product relation is not mass-independent. We also study the local thermodynamic stability of this black hole. The phase transition occurs at certain condition. Smarr mass formula and first law of thermodynamics have been derived. This mass-independent relation suggests they could turn out to be an universal quantity and further helps us to understanding the nature of black hole entropy (both interior and exterior) at the microscopic level. In the "Appendix", we have derived the thermodynamic products for 5D Einstein-Maxwell-Gauss-Bonnet black hole with vanishing cosmological constant.

  14. A Numerical Study on Electrical Percolation of Polymer-Matrix Composites with Hybrid Fillers of Carbon Nanotubes and Carbon Black

    Directory of Open Access Journals (Sweden)

    Yuli Chen

    2014-01-01

    Full Text Available The electrical percolation of polymer-matrix composites (PMCs containing hybrid fillers of carbon nanotubes (CNTs and carbon black (CB is estimated by studying the connection possibility of the fillers using Monte Carlo simulation. The 3D simulation model of CB-CNT hybrid filler is established, in which CNTs are modeled by slender capped cylinders and CB groups are modeled by hypothetical spheres with interspaces because CB particles are always agglomerated. The observation on the effects of CB and CNT volume fractions and dimensions on the electrical percolation threshold of hybrid filled composites is then carried out. It is found that the composite electrical percolation threshold can be reduced by increasing CNT aspect ratio, as well as increasing the diameter ratio of CB groups to CNTs. And adding CB into CNT composites can decrease the CNT volume needed to convert the composite conductivity, especially when the CNT volume fraction is close to the threshold of PMCs with only CNT filler. Different from previous linear assumption, the nonlinear relation between CB and CNT volume fractions at composite percolation threshold is revealed, which is consistent with the synergistic effect observed in experiments. Based on the nonlinear relation, the estimating equation for the electrical percolation threshold of the PMCs containing CB-CNT hybrid fillers is established.

  15. Black carbon at a roadside site in Beijing: Temporal variations and relationships with carbon monoxide and particle number size distribution

    Science.gov (United States)

    Song, Shaojie; Wu, Ye; Xu, Jiayu; Ohara, Toshimasa; Hasegawa, Shuichi; Li, Jiaqi; Yang, Liu; Hao, Jiming

    2013-10-01

    Black carbon (BC), carbon monoxide (CO), and particle number size distribution were measured near a major urban expressway of Beijing during summer and winter field campaigns in 2009. BC was also observed at urban and rural sites. The temporal variations of BC and its relationships with CO and particle number size distribution were analyzed. The average BC concentrations at the roadside site were 12.3 and 17.9 μg m-3 during the summer and winter campaigns, respectively. BC concentrations ranked in the order of roadside > urban > rural. A general diurnal pattern at all sites showed that the higher BC levels were observed at night. The diurnal pattern of summertime BC at the roadside site followed the variations of heavy-duty diesel vehicles (HDDVs). The increased proportion of HDDVs at night contributed to high ΔBC/ΔCO ratios. This study suggests that HDDVs are an important contributor to nighttime BC and particle number concentrations of both Aitken and accumulation modes near major roadways in Beijing, especially in summer.

  16. Black carbon in deep-sea sediments from the northeastern equatorial Pacific Ocean

    Science.gov (United States)

    Kim, D.; Lee, Y.; Hyeong, K.; Yoo, C.

    2011-12-01

    Deep-sea sediment core is a good archive for understanding the land-ocean interactions via atmosphere, due to it is little influenced by fluvial and continental shelf processes. This study dealt with black carbon(BC) in a 328 cm-long piston core collected from the northeastern equatorial Pacific Ocean (16°12'N, 125°59'W), covering the last 15 Ma (Hyeong at al., 2004). BC is a common name of carbon continuum formed by incomplete combustion of fossil fuels and plant materials. Though it may react with ozone and produce water-soluble organic carbon, BC has commonly refractory nature. Thus BC in preindustrial sediment can be a tracer of forest-fire events. BC is purely terrestrial in origin, and is transported to marine environments by atmospheric and fluvial processes. Therefore, distribution of BC in deep-sea sediments could be used to understand atmospheric circulation. Chemical oxidation was used to determine BC in this study following Lim and Cachier (1996). Concentration of BC varies from 0.010% to 0.233% of total sediments. Mass accumulation rate (MAR) of BC ranged between 0.077 mg/cm^2/1000 yrs and 47.49 mg/cm^21000 yrs. It is noted that MAR in sediments younger than 8 Ma (av. 9.0 mg/cm^2/1000 yrs) is higher than that in sediments older than 8 Ma (av. 3.2 mg/cm^2/1000 yrs). Stable carbon isotope value of BC increases with time from the low δ13C value near 13 Ma until it reaches the highest value near 4 Ma. Change of MAR seems to be related to the meridional migration of Intertropical Convergence Zone (ITCZ) at around 8 Ma in the study area (cf., Hyeong at al., 2004). Accordingly, higher BC content in sediment younger than 8 Ma seems to be accounted for by its derivation from the Northern Hemisphere compared to that from the Southern Hemisphere in older sediment. Increase of carbon isotope value with time seems to be related to expansion of C4 grassland. C4 grassland expansion might have been caused by change of atmosphreic cycle, which moved dry subtropical

  17. Geological and geomechanical properties of the carbonate rocks at the eastern Black Sea Region (NE Turkey)

    Science.gov (United States)

    Ersoy, Hakan; Yalçinalp, Bülent; Arslan, Mehmet; Babacan, Ali Erden; Çetiner, Gözde

    2016-11-01

    Turkey located in the Alpine-Himalayan Mountain Belt has 35% of the natural stone reserves of the world and has good quality marble, limestone, travertine and onyx reserves especially in the western regions of the country. The eastern Black Sea Region with a 1.4 million meters cubes reserve has a little role on the natural stone production in the country. For this reason, this paper deals with investigation on the potential of carbonate stone in the region and determination of the geological and geo-mechanical properties of these rocks in order to provide economic contribution to the national economy. While the study sites are selected among the all carbonate rock sites, the importance as well as the representative of the sites were carefully considered for the region. After representative samples were analyzed for major oxide and trace element compositions to find out petrochemical variations, the experimental program conducted on rock samples for determination of both physical and strength properties of the carbonate rocks. The results of the tests showed that there are significant variations in the geo-mechanical properties of the studied rock groups. The density values vary from 2.48 to 2.70 gr/cm3, water absorption by weight values range from 0.07 to 1.15% and the apparent porosity of the carbonate rocks are between 0.19 and 3.29%. However, the values of the UCS shows variation from 36 to 80 MPa. Tensile and bending strength values range from 3.2 to 7.5 MPa and 6.0-9.2 MPa respectively. Although the onyx samples have the lowest values of apparent porosity and water absorption by weight, these samples do not have the highest values of UCS values owing to occurrence of the micro-cracks. The UCS values of the rock samples were also found after cycling tests However, the limestone samples have less than 5% deterioration after freezing-thawing and wetting-drying tests, but travertine and onyx samples have more than 15% deterioration. Exception of the apparent

  18. Spatial, temporal and source contribution assessments of black carbon over the northern interior of South Africa

    Science.gov (United States)

    Euphinia Chiloane, Kgaugelo; Beukes, Johan Paul; Gideon van Zyl, Pieter; Maritz, Petra; Vakkari, Ville; Josipovic, Miroslav; Derick Venter, Andrew; Jaars, Kerneels; Tiitta, Petri; Kulmala, Markku; Wiedensohler, Alfred; Liousse, Catherine; Vuyisile Mkhatshwa, Gabisile; Ramandh, Avishkar; Laakso, Lauri

    2017-05-01

    After carbon dioxide (CO2), aerosol black carbon (BC) is considered to be the second most important contributor to global warming. This paper presents equivalent black carbon (eBC) (derived from an optical absorption method) data collected from three sites in the interior of South Africa where continuous measurements were conducted, i.e. Elandsfontein, Welgegund and Marikana, as well elemental carbon (EC) (determined by evolved carbon method) data at five sites where samples were collected once a month on a filter and analysed offline, i.e. Louis Trichardt, Skukuza, Vaal Triangle, Amersfoort and Botsalano.Analyses of eBC and EC spatial mass concentration patterns across the eight sites indicate that the mass concentrations in the South African interior are in general higher than what has been reported for the developed world and that different sources are likely to influence different sites. The mean eBC or EC mass concentrations for the background sites (Welgegund, Louis Trichardt, Skukuza, Botsalano) and sites influenced by industrial activities and/or nearby settlements (Elandsfontein, Marikana, Vaal Triangle and Amersfoort) ranged between 0.7 and 1.1, and 1.3 and 1.4 µg m-3, respectively. Similar seasonal patterns were observed at all three sites where continuous measurement data were collected (Elandsfontein, Marikana and Welgegund), with the highest eBC mass concentrations measured from June to October, indicating contributions from household combustion in the cold winter months (June-August), as well as savannah and grassland fires during the dry season (May to mid-October). Diurnal patterns of eBC at Elandsfontein, Marikana and Welgegund indicated maximum concentrations in the early mornings and late evenings, and minima during daytime. From the patterns it could be deduced that for Marikana and Welgegund, household combustion, as well as savannah and grassland fires, were the most significant sources, respectively.Possible contributing sources were

  19. Utilizing Colored Dissolved Organic Matter to Derive Dissolved Black Carbon Export by Arctic Rivers

    Directory of Open Access Journals (Sweden)

    Aron eStubbins

    2015-10-01

    Full Text Available Wildfires have produced black carbon (BC since land plants emerged. Condensed aromatic compounds, a form of BC, have accumulated to become a major component of the soil carbon pool. Condensed aromatics leach from soils into rivers, where they are termed dissolved black carbon (DBC. The transport of DBC by rivers to the sea is a major term in the global carbon and BC cycles. To estimate Arctic river DBC export, 25 samples collected from the six largest Arctic rivers (Kolyma, Lena, Mackenzie, Ob’, Yenisey and Yukon were analyzed for dissolved organic carbon (DOC, colored dissolved organic matter (CDOM, and DBC. A simple, linear regression between DOC and DBC indicated that DBC accounted for 8.9 ± 0.3% DOC exported by Arctic rivers. To improve upon this estimate, an optical proxy for DBC was developed based upon the linear correlation between DBC concentrations and CDOM light absorption coefficients at 254 nm (a254. Relatively easy to measure a254 values were determined for 410 Arctic river samples between 2004 and 2010. Each of these a254 values was converted to a DBC concentration based upon the linear correlation, providing an extended record of DBC concentration. The extended DBC record was coupled with daily discharge data from the six rivers to estimate riverine DBC loads using the LOADEST modeling program. The six rivers studied cover 53% of the pan-Arctic watershed and exported 1.5 ± 0.1 million tons of DBC per year. Scaling up to the full area of the pan-Arctic watershed, we estimate that Arctic rivers carry 2.8 ± 0.3 million tons of DBC from land to the Arctic Ocean each year. This equates to ~8% of Arctic river DOC export, slightly less than indicated by the simpler DBC vs DOC correlation-based estimate. Riverine discharge is predicted to increase in a warmer Arctic. DBC export was positively correlated with river runoff, suggesting that the export of soil BC to the Arctic Ocean is likely to increase as the Arctic warms.

  20. Utilizing Colored Dissolved Organic Matter to Derive Dissolved Black Carbon Export by Arctic Rivers

    Science.gov (United States)

    Stubbins, Aron; Spencer, Robert; Mann, Paul; Holmes, R.; McClelland, James; Niggemann, Jutta; Dittmar, Thorsten

    2015-10-01

    Wildfires have produced black carbon (BC) since land plants emerged. Condensed aromatic compounds, a form of BC, have accumulated to become a major component of the soil carbon pool. Condensed aromatics leach from soils into rivers, where they are termed dissolved black carbon (DBC). The transport of DBC by rivers to the sea is a major term in the global carbon and BC cycles. To estimate Arctic river DBC export, 25 samples collected from the six largest Arctic rivers (Kolyma, Lena, Mackenzie, Ob’, Yenisey and Yukon) were analyzed for dissolved organic carbon (DOC), colored dissolved organic matter (CDOM), and DBC. A simple, linear regression between DOC and DBC indicated that DBC accounted for 8.9 ± 0.3% DOC exported by Arctic rivers. To improve upon this estimate, an optical proxy for DBC was developed based upon the linear correlation between DBC concentrations and CDOM light absorption coefficients at 254 nm (a254). Relatively easy to measure a254 values were determined for 410 Arctic river samples between 2004 and 2010. Each of these a254 values was converted to a DBC concentration based upon the linear correlation, providing an extended record of DBC concentration. The extended DBC record was coupled with daily discharge data from the six rivers to estimate riverine DBC loads using the LOADEST modeling program. The six rivers studied cover 53% of the pan-Arctic watershed and exported 1.5 ± 0.1 million tons of DBC per year. Scaling up to the full area of the pan-Arctic watershed, we estimate that Arctic rivers carry 2.8 ± 0.3 million tons of DBC from land to the Arctic Ocean each year. This equates to ~8% of Arctic river DOC export, slightly less than indicated by the simpler DBC vs DOC correlation-based estimate. Riverine discharge is predicted to increase in a warmer Arctic. DBC export was positively correlated with river runoff, suggesting that the export of soil BC to the Arctic Ocean is likely to increase as the Arctic warms.

  1. Carbon black networking in elastomers monitored by simultaneous rheological and dielectric investigations

    Science.gov (United States)

    Steinhauser, Dagmar; Möwes, Markus; Klüppel, Manfred

    2016-12-01

    The rheo-dielectric response of carbon black filled elastomer melts is investigated by dielectric relaxation spectroscopy in the frequency range from 0.1 Hz up to 10 MHz during oszillatory shearing in a plate-plate rheometer. Various concentrations and types of carbon blacks dispersed in a non-crosslinked EPDM melt are considered. It is demonstrated that during heat treatment at low strain amplitude a pronounced flocculation of filler particles takes place leading to a successive increase of the shear modulus and conductivity. Followed up by a strain sweep, the filler network breaks up and both quantities decrease simultaneously with increasing strain amplitude. Two relaxation times, obtained from a Cole-Cole fit of the dielectric spectra, are identified, which both decrease strongly with increasing flocculation time. This behaviour is analyzed in the frame of fractal network models, describing the effect of structural disorder of the conducting carbon black network on the diffusive charge transport. Significant deviations from the predictions of percolation theory are observed, which are traced back to a superimposed cluster-cluster aggregation process (CCA). During flocculation, a universal scaling behaviour holds between the conductivity and the corresponding high frequency relaxation time, which fits all the measured data. The scaling exponent agrees fairly well with the prediction obtained from CCA. It is demonstrated that the underlying basic mechanism is a change of the correlation length of the filler network, i.e. the size of the fractal heterogeneities. This decreases during flocculation due to the formation of additional conductive paths, making the system more homogeneous. An addition less pronounced effect is found from nanoscopic gaps between adjacent filler particles, which decrease during flocculation. The same universal scaling behaviour, as obtained for flocculation, is found for temperature-dependent dielectric measurements of the cured

  2. Analysis and high resolution modelling of black carbon vertical profiles measured over three Italian valleys

    Science.gov (United States)

    Gandolfi, Ilaria; Curci, Gabriele; Falasca, Serena; Ferrero, Luca

    2017-04-01

    Analysis and high resolution modelling of black carbon vertical profiles measured over three Italian valleys Ilaria Gandolfi1,2, Gabriele Curci1,2, Serena Falasca1,2, Luca Ferrero3 1 Department of Physical and Chemical Sciences, University of L'Aquila, L'Aquila, Italy 2 Center of Excellence CETEMPS, University of L'Aquila, L'Aquila, Italy 3 POLARIS Research Centre, Department of Earth and Environmental Sciences, University of Milano-Bicocca, Piazza della Scienza 1, 20126, Milan, Italy Last decades were characterized by a growing interest in aerosols: mainly for their effect on human health and on the energy balance of solar and planetary radiation, thus their role in climate change. In this study, we analyze the evolution of vertical profile of black carbon (BC) through tethered balloon observations and chemistry-transport modelling. Black carbon is regarded as the second most important anthropogenic climate forcing agent and its concentration varies significantly depending on the altitude and the sources on the territory. In winter of 2010 University Of Milan Bicocca conducted three intensive measurements campaigns over three Italian basin valleys (Terni, Po Valley, Passiria Valley). The choice of the valleys was made taking into consideration the orography and the river basin structure. The measurement campaign was based on a helium-filled tethered balloon, on which the instrumentation for the analysis has been mounted; the instrumentation consisted on a meteorological station, an OPC, a cascade impactor and a micro-Aethalometer. Subsequently, at University of L'Aquila simulations were produced to help interpretation of these vertical aerosol profiles (mass, composition and distribution) and related optical properties (scattering, absorption) using a chemistry-transport model (WRF-CHIMERE) at high horizontal resolution (1 km). The analysis focused primarily on the calculation of the heating rate and of the Direct Radiative Effect (DRE), and on the analysis of the

  3. Modelling of Black and Organic Carbon Variability in the Northern Hemisphere

    Science.gov (United States)

    Kurganskiy, Alexander; Nuterman, Roman; Mahura, Alexander; Kaas, Eigil; Baklanov, Alexander; Hansen Sass, Bent

    2016-04-01

    Black and organic carbon as short-lived climate forcers have influence on air quality and climate in Northern Europe and Arctic. Atmospheric dispersion, deposition and transport of these climate forcers from remote sources is especially difficult to model in Arctic regions due to complexity of meteorological and chemical processes and uncertainties of emissions. In our study, the online integrated meteorology-chemistry/aerosols model Enviro-HIRLAM (Environment - High Resolution Limited Area Model) was employed for evaluating spatio-temporal variability of black and organic carbon aerosols in atmospheric composition in the Northern Hemisphere regions. The model setup included horizontal resolution of 0.72 deg, time step of 450 sec, 6 h meteorological surface data assimilation, 1 month spin-up; and model was run for the full year of 2010. Emissions included anthropogenic (ECLIPSE), shipping (AU_RCP&FMI), wildfires (IS4FIRES), and interactive sea salt, dust and DMS. Meteorological (from IFS at 0.75 deg) and chemical (from MACC Reanalysis at 1.125 deg) boundary conditions were obtained from ECMWF. Annual and month-to-month variability of mean concentration, accumulated dry/wet and total deposition fluxes is analyzed for the model domain and selected European and Arctic observation sites. Modelled and observed BC daily mean concentrations during January and July showed fair-good correlation (0.31-0.64) for stations in Germany, UK and Italy; however, for Arctic stations (Tiksi, Russia and Zeppelin, Norway) the correlations were negative in January, but higher correlations and positive (0.2-0.7) in July. For OC, it varied 0.45-0.67 in January and 0.19-0.57 in July. On seasonal scale, during both summer and winter seasons the BC and OC correlations are positive and higher for European stations compared with Arctic. On annual scale, both BC and OC correlations are positive and vary between 0.4-0.6 for European stations, and these are smoothed to negligible values for Arctic

  4. Spatial variability of aerosol and black carbon concentrations in the troposphere of the Russian Arctic

    Science.gov (United States)

    Kozlov, Valerii S.; Panchenko, Mikhail V.; Paris, Jean D.; Nédéléc, Philippe; Chernov, Dmitry G.; Shmargunov, Vladimir P.

    2015-11-01

    A cycle of flights of the Optik TU-134 Flying Laboratory of IAO SB RAS over regions of Western Siberia and the Russian Arctic (55.0-74.8°N, 61.3-82.9°E) was carried out on October 15-17 of 2014 within the framework of the YAK-AEROSIB Russian—French Project. The mass concentrations of submicron aerosol and Black Carbon (BC) in the troposphere up to a height of 8.5 km were measured in the flights. The ranges of variability were 0.3-20 μg/m3 for the aerosol concentration and 0.02-1 μg/m3 for the BC concentration. In the subpolar latitudes of 71-74.8°N, the lower levels of aerosol (0.8-6 μg/m3) and BC (0.02-0.3 μg/m3) were observed. The comparison of the results of airborne sensing in 2008 and 2014 has shown that in the Western Subartic the aerosol and BC concentrations in the vertical profiles up to six times exceeded those observed in the Eastern Subarctic (0.3-1 μg/m3 and 10-50 ng/m3). The excess of the mean integral BC concentrations and the aerosol optical depth was, on average, 2-2.5 times (0.16 mg/m2; 0.02). In the region of the Kara Sea at heights of 0.5-2 and 4-6 km, the excess of the aerosol content in the western sector in comparison with the eastern one was, on average, 2 times, while for the black carbon the excess achieved 7 times at heights of 1-2 km (0.25- 0.035 μg/m3). The mean integral concentrations of aerosol and black carbon ˜ 1.3 times exceeded those in the clearer eastern region of the sea (0.31 mg/m2; 0.049). The obtained estimates indicate the decrease of the aerosol and BC concentrations in the subpolar latitudes of the Russian Federation from the west to the east.

  5. Formation, transformation and transport of black carbon (charcoal) in terrestrial and aquatic ecosystems.

    Science.gov (United States)

    Forbes, M S; Raison, R J; Skjemstad, J O

    2006-10-15

    Black carbon (BC) is ubiquitous in terrestrial environments and its unique physical and chemical properties suggest that it may play an important role in the global carbon budget (GCB). A critical issue is whether the global production of BC results in significant amounts of carbon (C) being removed from the short-term bio-atmospheric carbon cycle and transferred to the long-term geological carbon cycle. Several dozen field and laboratory based studies of BC formation during the burning of biomass have been documented. Findings are difficult to interpret because they have been expressed in an inconsistent manner, and because different physical and chemical methods have been used to derive them. High error terms documented in many of these studies also highlight the problems associated with the quantification of the amount of biomass C consumed in fire, the amount of residue produced and the constituents of that residue. To be able to estimate the potential for BC as a carbon sink, issues regarding its definition, the methods used in its identification and measurement, and the way it is expressed in relation to other components of the carbon cycle need to be addressed. This paper presents BC data in a standard way; BC production as a percentage of the amount of C consumed by fire (BC/CC), which can be readily integrated into a larger carbon budget. Results from previous studies and new data from Australian ecosystems were recalculated in this way. As part of this process, several BC estimates derived solely from physical methods were discarded, based on their inability to accurately identify and quantify the BC component of the post-fire residue. Instead, more focus was placed on BC estimates obtained by chemical methods. This recalculated data lowered the estimate for BC formation in forest fires from 4% to 5% to <3% BC/CC. For savannah and grassland fires a value of <3% is consistent with reported data, but considerable variation among estimates remains. An

  6. Chemical Bonding and Structural Information of Black CarbonReference Materials and Individual Carbonaceous AtmosphericAerosols

    Energy Technology Data Exchange (ETDEWEB)

    Hopkins, Rebecca J.; Tivanski, Alexei V.; Marten, Bryan D.; Gilles, Mary K.

    2007-04-25

    The carbon-to-oxygen ratios and graphitic nature of a rangeof black carbon standard reference materials (BC SRMs), high molecularmass humic-like substances (HULIS) and atmospheric particles are examinedusing scanning transmission X-ray microscopy (STXM) coupled with nearedge X-ray absorption fine structure (NEXAFS) spectroscopy. UsingSTXM/NEXAFS, individual particles with diameter>100 nm are studied,thus the diversity of atmospheric particles collected during a variety offield missions is assessed. Applying a semi-quantitative peak fittingmethod to the NEXAFS spectra enables a comparison of BC SRMs and HULIS toparticles originating from anthropogenic combustion and biomass burns,thus allowing determination of the suitability of these materials forrepresenting atmospheric particles. Anthropogenic combustion and biomassburn particles can be distinguished from one another using both chemicalbonding and structural ordering information. While anthropogeniccombustion particles are characterized by a high proportion ofaromatic-C, the presence of benzoquinone and are highly structurallyordered, biomass burn particles exhibit lower structural ordering, asmaller proportion of aromatic-C and contain a much higher proportion ofoxygenated functional groups.

  7. Modeling water column partitioning of polychlorinated biphenyls to natural organic matter and black carbon.

    Science.gov (United States)

    Greene, Richard W; Di Toro, Dominic M; Farley, Kevin J; Phillips, Kathy L; Tomey, Cynthia

    2013-06-18

    High volume in situ surface water samples were collected from a tidal tributary of the Delaware Estuary using an Infiltrex sampling system equipped with a 1 μm particle filter and a XAD-2 resin column. Particulate and dissolved phase polychlorinated biphenyl (PCB) congeners were analyzed using high resolution gas chromatography/high resolution mass spectrometry to obtain detection levels in the femtograms per liter range. The data were fit to a four-phase equilibrium partitioning model including freely dissolved PCB, PCB bound to particulate organic carbon (POC), PCB bound to dissolved organic carbon (DOC), and PCB bound to black carbon (BC). Isotherms were assumed to be linear for POC and DOC and nonlinear for BC. The partition coefficient between BC and dissolved PCB was assumed to depend on the dihedral angle between the phenyl rings. Following parameter optimization, the correlation coefficient between the log of the modeled and measured apparent distribution coefficient Kp,app was 0.94, and the RMSE was 0.189 log units. Including BC in the model reduces the dissolved PCB phase concentration in the water column for all congeners, especially for the non-ortho and mono-ortho substituted congeners.

  8. Black carbon-mediated reduction of 2,4-dinitrotoluene by dithiothreitol.

    Science.gov (United States)

    Oh, Seok-Young; Son, Jong-Gil; Hur, Seung Hyun; Chung, Jin Suk; Chiu, Pei C

    2013-01-01

    By using various types of black carbon (BC), including chemically converted graphene (CCG), multiwalled carbon nanotubes (MWCNT), and granular activated carbon (GAC), BC-mediated reduction was investigated with 2,4-dinitrotoluene (DNT), a model nitroaromatic compound. We hypothesized that by providing sorption and electron transfer sites, BC can be used as a catalyst to accelerate DNT reduction by dithiothreitol (DTL), a thiol reductant. Results from batch experiments showed that CCG, MWCNT, and GAC could promote reduction of DNT by DTL. The yield ratio of the two aminonitro intermediates was approximately 1:1, which was consistent with that in a graphite system. However, fullerene did not significantly enhance the reduction of DNT, likely due to being a π acceptor. Kinetic data analysis showed that removal of DNT in the presence of BC and DTL was linearly proportional to the electrical conductivity of BC, suggesting that the graphitic structure of BC may be responsible for DNT removal. Our results indicate that the presence of BC materials may affect the fate of nitroaromatic compounds under electron-rich conditions.

  9. Finding consistency between different views of the absorption enhancement of black carbon: An observationally constrained hybrid model to support a transition in optical properties with mass fraction

    Science.gov (United States)

    Coe, H.; Allan, J. D.; Whitehead, J.; Alfarra, M. R. R.; Villegas, E.; Kong, S.; Williams, P. I.; Ting, Y. C.; Haslett, S.; Taylor, J.; Morgan, W.; McFiggans, G.; Spracklen, D. V.; Reddington, C.

    2015-12-01

    The mixing state of black carbon is uncertain yet has a significant influence on the efficiency with which a particle absorbs light. In turn, this may make a significant contribution to the uncertainty in global model predictions of the black carbon radiative budget. Previous modelling studies that have represented this mixing state using a core-shell approach have shown that aged black carbon particles may be considerably enhanced compared to freshly emitted black carbon due to the addition of co-emitted, weakly absorbing species. However, recent field results have demonstrated that any enhancement of absorption is minor in the ambient atmosphere. Resolving these differences in absorption efficiency is important as they will have a major impact on the extent to which black carbon heats the atmospheric column. We have made morphology-independent measurements of refractory black carbon mass and associated weakly absorbing material in single particles from laboratory-generated diesel soot and black carbon particles in ambient air influenced by traffic and wood burning sources and related these to the optical properties of the particles. We compared our calculated optical properties with optical models that use varying mixing state assumptions and by characterising the behaviour in terms of the relative amounts of weakly absorbing material and black carbon in a particle we show a sharp transition in mixing occurs. We show that the majority of black carbon particles from traffic-dominated sources can be treated as externally mixed and show no absorption enhancement, whereas models assuming internal mixing tend to give the best estimate of the absorption enhancement of thickly coated black carbon particles from biofuel or biomass burning. This approach reconciles the differences in absorption enhancement previously observed and offers a systematic way of treating the differences in behaviour observed.

  10. Detection of Carbon Monoxide Using Polymer-Composite Films with a Porphyrin-Functionalized Polypyrrole

    Science.gov (United States)

    Homer, Margie L.; Ryan, Margaret A.; Yen, Shiao-Ping S.; Lara, Liana M.; Shevade, Abhijit V.; Kisor, Adam

    2012-01-01

    Post-fire air constituents that are of interest to NASA include CO and some acid gases (HCl and HCN). CO is an important analyte to be able to sense in human habitats since it is a marker for both prefire detection and post-fire cleanup. The need exists for a sensor that can be incorporated into an existing sensing array architecture. The CO sensor needs to be a low-power chemiresistor that operates at room temperature; the sensor fabrication techniques must be compatible with ceramic substrates. Early work on the JPL ElectronicNose indicated that some of the existing polymer-carbon black sensors might be suitable. In addition, the CO sensor based on polypyrrole functionalized with iron porphyrin was demonstrated to be a promising sensor that could meet the requirements. First, pyrrole was polymerized in a ferric chloride/iron porphyrin solution in methanol. The iron porphyrin is 5, 10, 15, 20-tetraphenyl-21H, 23Hporphine iron (III) chloride. This creates a polypyrrole that is functionalized with the porphyrin. After synthesis, the polymer is dried in an oven. Sensors were made from the functionalized polypyrrole by binding it with a small amount of polyethylene oxide (600 MW). This composite made films that were too resistive to be measured in the device. Subsequently, carbon black was added to the composite to bring the sensing film resistivity within a measurable range. A suspension was created in methanol using the functionalized polypyrrole (90% by weight), polyethylene oxide (600,000 MW, 5% by weight), and carbon black (5% by weight). The sensing films were then deposited, like the polymer-carbon black sensors. After deposition, the substrates were dried in a vacuum oven for four hours at 60 C. These sensors showed good response to CO at concentrations over 100 ppm. While the sensor is based on a functionalized pyrrole, the actual composite is more robust and flexible. A polymer binder was added to help keep the sensor material from delaminating from the

  11. Functionalized Activated Carbon Derived from Biomass for Photocatalysis Applications Perspective

    Directory of Open Access Journals (Sweden)

    Samira Bagheri

    2015-01-01

    Full Text Available This review highlighted the developments of safe, effective, economic, and environmental friendly catalytic technologies to transform lignocellulosic biomass into the activated carbon (AC. In the photocatalysis applications, this AC can further be used as a support material. The limits of AC productions raised by energy assumption and product selectivity have been uplifted to develop sustainable carbon of the synthesis process, where catalytic conversion is accounted. The catalytic treatment corresponding to mild condition provided a bulk, mesoporous, and nanostructure AC materials. These characteristics of AC materials are necessary for the low energy and efficient photocatalytic system. Due to the excellent oxidizing characteristics, cheapness, and long-term stability, semiconductor materials have been used immensely in photocatalytic reactors. However, in practical, such conductors lead to problems with the separation steps and loss of photocatalytic activity. Therefore, proper attention has been given to develop supported semiconductor catalysts and certain matrixes of carbon materials such as carbon nanotubes, carbon microspheres, carbon nanofibers, carbon black, and activated carbons have been recently considered and reported. AC has been reported as a potential support in photocatalytic systems because it improves the transfer rate of the interface charge and lowers the recombination rate of holes and electrons.

  12. Black carbon trends in southwestern Iberia in the context of the financial and economic crisis. The role of bioenergy.

    Science.gov (United States)

    Malico, Isabel; Pereira, Sérgio Nepomuceno; Costa, Maria João

    2017-01-01

    Since black carbon concentrations are useful to reveal changes in anthropogenic activities, measurements taken from 2007 to 2015 in a Portuguese city are used to assess to which extent the ambient air was impacted by the economic crisis. The average black carbon concentrations are representative of an urban area of small size (1.3 ± 1.3 μg m(-3)). The highest concentrations are observed in the heating season, being biomass combustion one of the causes for the high values. The daily cycle of black carbon concentrations presents both morning and evening peaks, mainly due to road traffic and, in the heating season, to domestic heating as well. The yearly averaged black carbon mass concentrations decreased 33 % from 2007 to 2015, possibly due to a combination of the economic recession and environmental legislation. The reduction in road traffic led to a decrease in the daily morning peak from 2007 to 2015. This reduction was not followed by a decrease in the evening peak, explained by an increase in biomass burning. Biomass is the cheapest heating fuel in Portugal, and its consumption increased in the aftermath of the economic crisis. The use of bioenergy is an alternative to fossil fuels and presents many advantages. However, energy policies should discourage inefficient biomass burning and promote better ways of exploiting the available energy resources and emission air pollution mitigation strategies.

  13. Reinforcing effect of plasma modified halloysite nanotubes in a carbon black filled natural rubber-butadien rubber matrix

    NARCIS (Netherlands)

    Poikelispaa, Minna; Das, Amit; Dierkes, Wilma; Vuorinen, Jyrki

    2011-01-01

    Rubber composites are generally produced by the direct incorporation of fillers like carbon black and/or silica into the rubber matrix. The incorporation of different types of nanofillers is the subject of recent research with the aim of preparing composites with special compositions and properties.

  14. INFLUENCE OF BIOLOGICALLY ACTIVE AGENTS ON A STRUCTURAL STATE AND THE ENZYMATIC ACTIVITY OF BLACK ORDINARY CARBONATED SOIL

    Directory of Open Access Journals (Sweden)

    Lychman V. A.

    2014-04-01

    Full Text Available The results of a long-term research of the influence of various biologically active agents (a humic preparation Lignogumat and microbiological Baikal EM fertilizer on a structural state and the enzymatic activity of ordinary carbonated black soil are presented. It has been established that biologically active substances contribute to increased enzymatic activity, humus and improve the soil structure

  15. Black carbon concentration and deposition estimations in Finland by the regional aerosol–climate model REMO-HAM

    Directory of Open Access Journals (Sweden)

    A. I. Hienola

    2013-04-01

    Full Text Available The prediction skill of the regional aerosol–climate model REMO-HAM was assessed against the black carbon (BC concentration measurements from five locations in Finland, with focus on Hyytiälä station for the year 2005. We examined to what extent the model is able to reproduce the measurements using several statistical tools: median comparison, overlap coefficient (OVL; the common area under two probability distributions curves and Z score (a measure of standard deviation, shape and spread of the distributions. The results of the statistics showed that the model is biased low. The local and regional emissions of BC have a significant contribution, and the model tendency to flatten the observed BC is most likely dominated by the lack of domestic burning of biofuel in the emission inventories. A further examination of the precipitation data from both measurements and model showed that there is no correlation between REMO's excessive precipitation and BC underestimation. This suggests that the excessive wet removal is not the main cause of the low black carbon concentration output. In addition, a comparison of wind directions in relation with high black carbon concentrations shows that REMO-HAM is able to predict the BC source directions relatively well. Cumulative black carbon deposition fluxes over Finland were estimated, including the deposition on snow.

  16. Three-dimensional shapes and spatial distributions of Pt and PtCr catalyst nanoparticles on carbon black

    DEFF Research Database (Denmark)

    Gontard, Lionel Cervera; Dunin-Borkowski, Rafal E.; Ozkaya, D.

    2008-01-01

    High-angle annular dark-field scanning transmission electron microscopy tomography is applied to the study of Pt and PtCr nanoparticles supported on carbon black, which are used as heterogeneous catalysts in the electrodes of proton exchange membrane fuel cells. By using electron tomography, the ...

  17. Mutation spectrum in FE1-MUTA(TM) Mouse lung epithelial cells exposed to nanoparticulate carbon black

    DEFF Research Database (Denmark)

    Jacobsen, Nicklas Raun; White, Paul A; Gingerich, John

    2011-01-01

    It has been shown previously that carbon black (CB), Printex 90 exposure induces cII and lacZ mutants in the FE1-Muta(TM) Mouse lung epithelial cell line and causes oxidatively damaged DNA and the production of reactive oxygen species (ROS). The purpose of this study was to determine the mutation...

  18. Inflammation and Vascular Effects after Repeated Intratracheal Instillations of Carbon Black and Lipopolysaccharide

    DEFF Research Database (Denmark)

    Christophersen, Daniel Vest; Jacobsen, Nicklas Raun; Jensen, Ditte Marie;

    2016-01-01

    .5% plasma extracted from CB-exposed ApoE-/- mice caused vasoconstriction in aorta rings isolated from naïve mice; this effect was abolished by the treatment with the serotonin receptor antagonist Ketanserin. In conclusion, repeated pulmonary exposure to nanosized CB and LPS caused lung inflammation without......Inflammation and oxidative stress are considered the main drivers of vasomotor dysfunction and progression of atherosclerosis after inhalation of particulate matter. In addition, new studies have shown that particle exposure can induce the level of bioactive mediators in serum, driving vascular......- and systemic toxicity. We aimed to investigate if pulmonary inflammation would accelerate nanoparticle-induced atherosclerotic plaque progression in Apolipoprotein E knockout (ApoE-/-) mice. ApoE -/- mice were exposed to vehicle, 8.53 or 25.6 μg nanosized carbon black (CB) alone or spiked with LPS (0.2 μg...

  19. Numerical modelling of the internal mixing by coagulation of black carbon particles in aircraft exhaust

    Energy Technology Data Exchange (ETDEWEB)

    Ohlsson, S.; Stroem, J. [Stockholm Univ. (Sweden). Dept. of Meteorology

    1997-12-31

    When exhaust gases from an aircraft engine mix with ambient air the humidity may reach water saturation and water droplets will form on the available cloud condensation nuclei (CCN). It is still not resolved if the CCN, on which the cloud droplets form, are mainly particles present in the ambient air or particles emitted by the aircraft. It the exhaust from a jet engine the particles are believed to consist mainly of black carbon (BC) and sulfate. The aim is to study, with the help of a numerical model, how a two-component aerosol (i.e. BC and sulfate) in an exhaust trail may be transformed in terms of hygroscopicity by coagulation mixing and how this may depend on the sulfur content in the fuel. (R.P.) 15 refs.

  20. Investigation of Pm-75 carbon black addition on the properties of protective polymer coatings

    Science.gov (United States)

    Sapronov, Oleksandr; Maruschak, Pavlo; Buketova, Natalia; Leschenko, Oleksandr; Panin, Sergey

    2016-11-01

    The influence of the loading of fine furnace carbon black on the physical-mechanical, thermal-physical properties and structure of protective coatings was investigated. It is shown that for the formation of coatings with enhanced adhesion characteristics, the optimal weight fraction of additives should make q = 25 wt %, while for the formation of coatings with enhanced cohesive characteristics, that of additives should be q = 20 wt %. The optical-microscopy-based technique was employed to investigate the structure of the fracture patterns. A uniform fracture surface topology was revealed, which characterizes the viscous character of material fracture when content of the additives is equal to q = 10-30 wt %, which provides a significant improvement of physical and mechanical properties of the developed materials.

  1. Synthesis and characterization of conducting composites of polyaniline and carbon black with high thermal stability

    Directory of Open Access Journals (Sweden)

    Fabio R. Simões

    2009-01-01

    Full Text Available In this work, a detailed chemical route to prepare thermally stable polyaniline (PANI/carbon black (CB composites is described. The syntheses were performed by chemical polymerization of aniline over CB particles, using different PANI/CB mass ratios. The thermal and electrical properties were characterized. Composites with mass ratio up to 65:35 (PANI:CB showed excellent thermal stability maintaining their conducting properties when thermally treated at 230 °C for two hours, which is adequate to process these materials. Moreover, the results showed an important reduction in the surface area of the composites which have a good relationship with the improvement of the rheological properties in melt processing.

  2. Continental Scale Antarctic deposition of sulphur and black carbon from anthropogenic and volcanic sources

    Directory of Open Access Journals (Sweden)

    H.-F. Graf

    2009-12-01

    Full Text Available While Antarctica is often described as a pristine environment, the potential threats from local pollution sources including tourist ships and emissions associated with scientific activities have recently been raised. However, to date there has been no systematic attempt to model the impacts of such pollutants at the continental scale. Indeed, until very recently there was not even a sulphur emission budget available for Antarctica. Here we present the first comprehensive study of atmospheric pollution in Antarctica using a limited area chemistry climate model, and a monthly emissions inventory for sulphur from maintenance of research stations, ground and air traffic, shipping and the active volcano Mt. Erebus. We find that ship emissions, both sulphurous and black carbon, dominate anthropogenic pollution near the ground. These are likely to rise considerably if recent trends in tourism continue.

  3. Inflammation and Vascular Effects after Repeated Intratracheal Instillations of Carbon Black and Lipopolysaccharide

    DEFF Research Database (Denmark)

    Christophersen, Daniel Vest; Jacobsen, Nicklas Raun; Jensen, Ditte Marie

    2016-01-01

    -and systemic toxicity. We aimed to investigate if pulmonary inflammation would accelerate nanoparticle-induced atherosclerotic plaque progression in Apolipoprotein E knockout (ApoE-/-) mice. ApoE-/- mice were exposed to vehicle, 8.53 or 25.6 mu g nanosized carbon black (CB) alone or spiked with LPS (0.2 mu g...... mediators in plasma of exposed ApoE-/- mice was assessed in aorta rings isolated from naive C57BL/6 mice. Pulmonary exposure to CB and/or LPS resulted in pulmonary inflammation with a robust influx of neutrophils. The CB exposure did not promote plaque progression in aorta or BCA. Incubation with 0.......5% plasma extracted from CB-exposed ApoE-/- mice caused vasoconstriction in aorta rings isolated from naive mice; this effect was abolished by the treatment with the serotonin receptor antagonist Ketanserin. In conclusion, repeated pulmonary exposure to nanosized CB and LPS caused lung inflammation without...

  4. Continental scale Antarctic deposition of sulphur and black carbon from anthropogenic and volcanic sources

    Directory of Open Access Journals (Sweden)

    H.-F. Graf

    2010-03-01

    Full Text Available While Antarctica is often described as a pristine environment, there is an increasing awareness of the potential threats from local pollution sources including tourist ships and emissions associated with scientific activities. However, to date there has been no systematic attempt to model the impacts of such pollutants at the continental scale. Indeed, until very recently there was not even a sulphur emission budget available for Antarctica. Here we present the first comprehensive study of atmospheric pollution in Antarctica using a limited area chemistry climate model, and a monthly emissions inventory for sulphur from maintenance of research stations, ground and air traffic, shipping and the active Erebus volcano. We find that ship emissions, both sulphurous and black carbon, dominate anthropogenic pollution near the ground. Their prevalence is likely to rise dramatically if recent trends in tourism continue.

  5. Individual particle morphology, coatings, and impurities of black carbon aerosols in Antarctic ice and tropical rainfall

    Science.gov (United States)

    Ellis, Aja; Edwards, Ross; Saunders, Martin; Chakrabarty, Rajan K.; Subramanian, R.; Timms, Nicholas E.; Riessen, Arie; Smith, Andrew M.; Lambrinidis, Dionisia; Nunes, Laurie J.; Vallelonga, Paul; Goodwin, Ian D.; Moy, Andrew D.; Curran, Mark A. J.; Ommen, Tas D.

    2016-11-01

    Black carbon (BC) aerosols are a large source of climate warming, impact atmospheric chemistry, and are implicated in large-scale changes in atmospheric circulation. Inventories of BC emissions suggest significant changes in the global BC aerosol distribution due to human activity. However, little is known regarding BC's atmospheric distribution or aged particle characteristics before the twentieth century. Here we investigate the prevalence and structural properties of BC particles in Antarctic ice cores from 1759, 1838, and 1930 Common Era (C.E.) using transmission electron microscopy and energy-dispersive X-ray spectroscopy. The study revealed an unexpected diversity in particle morphology, insoluble coatings, and association with metals. In addition to conventionally occurring BC aggregates, we observed single BC monomers, complex aggregates with internally, and externally mixed metal and mineral impurities, tar balls, and organonitrogen coatings. The results of the study show BC particles in the remote Antarctic atmosphere exhibit complexity that is unaccounted for in atmospheric models of BC.

  6. Research on properties of carbon black/polypropylene composites by dynamic injection molding

    Science.gov (United States)

    Wu, Ming-Chun; He, Guang-Jian; Huang, Zhao-Xia; Zhou, Li-Ying; He, He-Zhi

    2016-03-01

    Polymer composites filled with conductive carbon black (CB) are gaining popularity for electromagnetic shielding applications. Dynamic injection molding method was adopted to study the influences of vibration force field on electrical properties of polypropylene/CB composites. The results showed that the percolation phenomenon of conductivity of composites occurred at 15wt% and the calculated SE was positive correlated with the variation trend of conductivity. The calculated SE of composite was more than 30dB at a CB concentration of 30wt%, which could obtain good shielding effects. The result could offer optimum vibration parameters for producing electromagnetic shielding composites by respectively changing the amplitudes and frequencies of the vibration force field.

  7. Spatio-temporal variations of black carbon concentrations in the Megacity Beijing.

    Science.gov (United States)

    Schleicher, Nina; Norra, Stefan; Fricker, Mathieu; Kaminski, Uwe; Chen, Yizhen; Chai, Fahe; Wang, Shulan; Yu, Yang; Cen, Kuang

    2013-11-01

    The spatial and temporal distribution and the flux of black carbon (BC) concentration in Beijing were continuously investigated over a two-year period at five sites to highlight the relative influence of contributing sources. The results demonstrate firstly that there is significant spatio-temporal variability of BC in Beijing. Highest concentrations occurred during winter primarily due to stagnant meteorological conditions, and seasonal BC sources, such as coal combustion for heating purposes. Biomass burning was identified as a minor seasonal source during the summer months. BC also varied spatially with higher concentrations in the SE of Beijing and lower concentrations in the NW, due to the differing emission intensity of various local BC sources such as traffic and industry. Frequently, overnight BC concentrations were higher due to specific meteorological conditions, such as the lower urban mixing layer height and various anthropogenic activities, such as exclusive night-time heavy duty vehicle traffic in the inner-city.

  8. A pressure-sensitive carbon black cement composite for traffic monitoring

    KAUST Repository

    Monteiro, A.O.

    2017-08-17

    Recent advances in nanotechnology have guided the development of a new generation of multifunctional construction materials. An example of this are cement-based composites, some of which can be used not just to pave roads but also to monitor them. A cement composite, integrating a carbon black (CB) filler, was used as a piezoresistive sensor to identify different cyclic compressive loadings, at temperatures ranging from 15°C to 45°C. The mechanical essays were performed under realistic conditions using 600cm3 specimens and uniaxial loads typical of automobile traffic. A linear and reversible pressure-sensing performance was found with gauge factors ranging from 40 to 60. Overall, these results show that CB/cement composites can act as stress-sensitive materials for traffic monitoring.

  9. NONLINEAR CURRENT-VOLTAGE CHARACTERISTICS OF CONDUCTIVE POLYETHYLENE COMPOSITES WITH CARBON BLACK FILLED PET MICROFIBRILS

    Institute of Scientific and Technical Information of China (English)

    Qian-ying Chen; Jing Gao; Kun Dai; Huan Pang; Jia-zhuang Xu; Jian-hua Tang; Zhong-ming Li

    2013-01-01

    Current-voltage electrical behavior of in situ microfibrillar carbon black (CB)/poly(ethylene terephthalate)(PET)/polyethylene (PE) (m-CB/PET/PE) composites with various CB concentrations at ambient temperatures was studied under a direct-current electric field.The current-voltage (Ⅰ-Ⅴ) curves exhibited nonlinearity beyond a critical value of voltage.The dynamic random resistor network (DRRN) model was adopted to semi-qualitatively explain the nonlinear conduction behavior of m-CB/PET/PE composites.Macroscopic nonlinearity originated from the interracial interactions between CB/PET micro fibrils and additional conduction channels.Combined with the special conductive networks,an illustration was proposed to interpret the nonlinear Ⅰ-Ⅴ characteristics by a field emission or tunneling mechanism between CB particles in the CB/PET microfibers intersections.

  10. Radiative absorption enhancements due to the mixing state of atmospheric black carbon

    Energy Technology Data Exchange (ETDEWEB)

    Cappa, Christopher D.; Onasch, Timothy B.; Massoli, Paola; Worsnop, Douglas R.; Bates, Timothy S.; Cross, Eben S.; Davidovits, Paul; Hakala, Jani; Hayden, Katherine; Jobson, Bertram Thomas; Kolesar, K. R.; Lack,