Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus Preliminary Evaluation Results

Science.gov (United States)

2008-10-16

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The report discusses the planned fuel cell bus demonstration and equipment us...

BC Transit Fuel Cell Bus Project: Evaluation Results Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-02-01

This report evaluates a fuel cell electric bus demonstration led by British Columbia Transit (BC Transit) in Whistler, Canada. BC Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's National Renewable Energy Laboratory to evaluate the buses in revenue service. This evaluation report covers two years of revenue service data on the buses from April 2011 through March 2013.

An updated assessment of the prospects for fuel cell-powered buses. An information paper

Energy Technology Data Exchange (ETDEWEB)

Sanderson, T.K. [Future Energy Solutions, Harwell (United Kingdom)

2005-07-01

This report presents updated conclusions of the Department of Trade and Industry's research and development programme to assess the commercial prospects for advanced fuel cells in buses. The programme has focussed on low temperature solid polymer fuel cells (SPFCs) for transport and combined heat and power (CHP)/distributed power and high temperature solid oxide fuel cells (SOFCs) for CHP/distributed power. As well as assessing the prospects for SPFCs in buses, the report examines those for alkaline fuel cells (AFCs) and phosphoric acid fuel cells (PAFCs) in buses. The report provides an assessment of the status of technology development for different types of fuel cells in terms of applications to buses and offers estimates of market potential. Some fuel-cell powered buses are now available for demonstration purposes but the report concludes that truly commercial sales are unlikely to start before 2010 and widespread deployment is expected to take a further ten years after that. Buses have now slipped behind cars in terms of worldwide deployment. The issue of fuel choice is considered largely resolved with most fleet vehicle/bus manufacturers currently focussing on hydrogen as a fuel. A discussion of the prospects and barriers for fuel cell buses concludes that cost reduction is now the major barrier to the successful commercialisation of fuel cells in buses. More demonstration prototypes and field trials are required to provide information on energy, environmental and economic performance of fuel cell buses. Field trials could also provide information to assist the development of refuelling systems, fuel storage systems, stacks and other system components and to gain experience of building integrated fuel cell systems.

Real-time measurements of nitrogen oxide emissions from in-use New York City transit buses using a chase vehicle.

Science.gov (United States)

Shorter, Joanne H; Herndon, Scott; Zahniser, Mark S; Nelson, David D; Wormhoudt, Joda; Demerjian, Kenneth L; Kolb, Charles E

2005-10-15

New diesel engine technologies and alternative fuel engines are being introduced into fleets of mass transit buses to try to meet stricter emission regulations of nitrogen oxides and particulates: Real-time instruments including an Aerodyne Research tunable infrared laser differential absorption spectrometer (TILDAS) were deployed in a mobile laboratory to assess the impact of the implementation of the new technologies on nitrogen oxide emissions in real world driving conditions. Using a "chase" vehicle sampling strategy, the mobile laboratory followed target vehicles, repeatedly sampling their exhaust. Nitrogen oxides from approximately 170 in-use New York City mass transit buses were sampled during the field campaigns. Emissions from conventional diesel buses, diesel buses with continuously regenerating technology (CRT), diesel hybrid electric buses, and compressed natural gas (CNG) buses were compared. The chase vehicle sampling method yields real world emissions that can be included in more realistic emission inventories. The NO, emissions from the diesel and CNG buses were comparable. The hybrid electric buses had approximately one-half the NOx emissions. In CRT diesels, NO2 accounts for about one-third of the NOx emitted in the exhaust, while for non-CRT buses the NO2 fraction is less than 10%.

Environmental, health, and safety issues of fuel cells in transportation. Volume 1: Phosphoric acid fuel-cell buses

Energy Technology Data Exchange (ETDEWEB)

Ring, S

1994-12-01

The U.S. Department of Energy (DOE) chartered the Phosphoric Acid Fuel-Cell (PAFC) Bus Program to demonstrate the feasibility of fuel cells in heavy-duty transportation systems. As part of this program, PAFC- powered buses are being built to meet transit industry design and performance standards. Test-bed bus-1 (TBB-1) was designed in 1993 and integrated in March 1994. TBB-2 and TBB-3 are under construction and should be integrated in early 1995. In 1987 Phase I of the program began with the development and testing of two conceptual system designs- liquid- and air-cooled systems. The liquid-cooled PAFC system was chosen to continue, through a competitive award, into Phase H, beginning in 1991. Three hybrid buses, which combine fuel-cell and battery technologies, were designed during Phase III. After completing Phase II, DOE plans a comprehensive performance testing program (Phase HI) to verify that the buses meet stringent transit industry requirements. The Phase III study will evaluate the PAFC bus and compare it to a conventional diesel bus. This NREL study assesses the environmental, health, and safety (EH&S) issues that may affect the commercialization of the PAFC bus. Because safety is a critical factor for consumer acceptance of new transportation-based technologies the study focuses on these issues. The study examines health and safety together because they are integrally related. In addition, this report briefly discusses two environmental issues that are of concern to the Environmental Protection Agency (EPA). The first issue involves a surge battery used by the PAFC bus that contains hazardous constituents. The second issue concerns the regulated air emissions produced during operation of the PAFC bus.

NREL Evaluates Performance of Fast-Charge Electric Buses

Energy Technology Data Exchange (ETDEWEB)

2016-09-16

This real-world performance evaluation is designed to enhance understanding of the overall usage and effectiveness of electric buses in transit operation and to provide unbiased technical information to other agencies interested in adding such vehicles to their fleets. Initial results indicate that the electric buses under study offer significant fuel and emissions savings. The final results will help Foothill Transit optimize the energy-saving potential of its transit fleet. NREL's performance evaluations help vehicle manufacturers fine-tune their designs and help fleet managers select fuel-efficient, low-emission vehicles that meet their bottom line and operational goals. help Foothill Transit optimize the energy-saving potential of its transit fleet. NREL's performance evaluations help vehicle manufacturers fine-tune their designs and help fleet managers select fuel-efficient, low-emission vehicles that meet their bottom line and operational goals.

Design Guidelines for Bus Transit Systems Using Liquefied Petroleum Gas (LPG) as an Alternative Fuel.

Science.gov (United States)

1996-09-01

The use of alternative fuels to power transit buses is steadily increasing. Several fuels, including Liquefied Petroleum Gas (LPG), Compressed Natural Gas (CNG), and Methanol/Ethanol, are already being used in buses. At present, there do not exist co...

Development of CH{sub 3}OH fueled PEMFC power plants for hybrid transit buses

Energy Technology Data Exchange (ETDEWEB)

Baumert, R; Cooper, R; Feasey, G [DBB Fuel Cell Engines Corp., Poway, CA (United States)

1999-12-31

An overview of the methanol fuel cell power system was provided, identifying improved efficiency and reduced emissions as the principal advantages. Four critical tasks regarding on-board fuel processing were described: (1) efficient methanol conversion (steam reforming), (2) effective reformate purification (selective catalytic oxidation), (3) optimized heat integration, and (4) rapid response to transients. A description of a 100 kW PEM fuel cell bus engine package was also presented. As far as a development time table is concerned, the DBB Fuel Cell Engines Corp. of Poway California has completed two methanol fueled PEMFC power plants, fabrication of the initial 100 kW PEMFC engine is in progress and scheduled for delivery by 1998. The two methanol fueled commercial products which are in the planning stages are the 100 and 200 kW class FCPS for hybrid and non-hybrid buses and other applications. tabs., figs.

Comparative study of fuel cell, battery and hybrid buses for renewable energy constrained areas

Science.gov (United States)

Stempien, J. P.; Chan, S. H.

2017-02-01

Fuel cell- and battery-based public bus technologies are reviewed and compared for application in tropical urban areas. This paper scrutinizes the reported literature on fuel cell bus, fuel cell electric bus, battery electric bus, hybrid electric bus, internal combustion diesel bus and compressed natural gas bus. The comparison includes the capital and operating costs, fuel consumption and fuel cycle emissions. To the best of authors knowledge, this is the first study to holistically compare hydrogen and battery powered buses, which is the original contribution of this paper. Moreover, this is the first study to focus on supplying hydrogen and electricity from fossil resources, while including the associated emissions. The study shows that compressed natural gas and hybrid electric buses appear to be the cheapest options in terms of total cost of ownership, but they are unable to meet the EURO VI emissions' standard requirement. Only fuel cell based buses have the potential to achieve the emissions' standard when the fuel cycle based on fossil energy was considered. Fuel cell electric buses are identified as a technology allowing for the largest CO2 emission reduction, making ∼61% decrease in annual emissions possible.

BC Transit Fuel Cell Bus Project Evaluation Results: Second Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Post, M.

2014-09-01

Second report evaluating a fuel cell electric bus (FCEB) demonstration led by British Columbia Transit (BC Transit) in Whistler, Canada. BC Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's National Renewable Energy Laboratory to evaluate the buses in revenue service. NREL published its first report on the demonstration in February 2014. This report is an update to the previous report; it covers 3 full years of revenue service data on the buses from April 2011 through March 2014 and focuses on the final experiences and lessons learned.

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Third Evaluation Report and Appendices

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2010-01-01

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The prototype fuel cell bus was manufactured by Van Hool and ISE Corp. and features an electric hybrid drive system with a UTC Power PureMotion 120 Fuel Cell Power System and ZEBRA batteries for energy storage. The fuel cell bus started operation in April 2007, and evaluation results through October 2009 are provided in this report.

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Second Evaluation Report and Appendices

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2009-05-01

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The evaluation period in this report (January 2008 through February 2009) has been chosen to coincide with a UTC Power propulsion system changeout that occurred on January 15, 2008.

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2013

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gikakis, Christina [Federal Transit Administration, Washington, DC (United States)

2013-12-01

This report is the seventh in an annual series of reports that summarize the progress of fuel cell electric bus (FCEB) development in the United States and discuss the achievements and challenges of introducing fuel cell propulsion in transit. The report also provides a snapshot of current FCEB performance results from August 2012 through July 2013 for five FCEB demonstrations at four transit agencies.

Fuel Cell Buses in U.S. Transit Fleets : Current Status 2014

Science.gov (United States)

2014-12-03

This report, published annually, summarizes the progress of fuel cell electric bus (FCEB) development in the United States and discusses the achievements and challenges of introducing fuel cell propulsion in transit. Various stakeholders, including d...

Assessment of alternative fuel and powertrain transit bus options using real-world operations data: Life-cycle fuel and emissions modeling

International Nuclear Information System (INIS)

Xu, Yanzhi; Gbologah, Franklin E.; Lee, Dong-Yeon; Liu, Haobing; Rodgers, Michael O.; Guensler, Randall L.

2015-01-01

Highlights: • We present a practical fuel and emissions modeling tool for alternative fuel buses. • The model assesses well-to-wheels emissions impacts of bus fleet decisions. • Mode-based approach is used to account for duty cycles and local conditions. • A case study using real-world operations data from Atlanta, GA is presented. • Impacts of alternative bus options depend on operating and geographic features. - Abstract: Hybrid and electric powertrains and alternative fuels (e.g., compressed natural gas (CNG), biodiesel, or hydrogen) can often reduce energy consumption and emissions from transit bus operations relative to conventional diesel. However, the magnitude of these energy and emissions savings can vary significantly, due to local conditions and transit operating characteristics. This paper introduces the transit Fuel and Emissions Calculator (FEC), a mode-based life-cycle emissions modeling tool for transit bus and rail technologies that compares the performance of multiple alternative fuels and powertrains across a range of operational characteristics and conditions. The purpose of the FEC is to provide a practical, yet technically sophisticated tool for regulatory agencies and policy analysts in assessing transit fleet options. The FEC’s modal modeling approach estimates emissions as a function of engine load, which in turn is a function of transit service parameters, including duty cycle (idling and speed-acceleration profile), road grade, and passenger loading. This approach allows for customized assessments that account for local conditions. Direct emissions estimates are derived from the scaled tractive power (STP) operating mode bins and emissions factors employed in the U.S. EPA’s MOVES (MOtor Vehicle Emissions Simulator) model. Life-cycle emissions estimates are calculated using emissions factors from the GREET (Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation) model. The case study presented in this paper

Fuel Cell Buses in U.S. Transit Fleets : Current Status 2015

Science.gov (United States)

2015-12-01

This report, published annually, summarizes the progress of fuel cell electric bus (FCEB) development in the United States and discusses the achievements and challenges of introducing fuel cell propulsion in transit. The report provides a summary of ...

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2017

Science.gov (United States)

2017-11-01

This report, published annually, summarizes the progress of fuel cell electric bus (FCEB) development in the United States and discusses the achievements and challenges of introducing fuel cell propulsion in transit. The report provides a summary of ...

Fuel Cell Buses in U.S. Transit Fleets : Current Status 2013

Science.gov (United States)

2013-12-01

This report is the seventh in an annual series of reports that summarize the progress of fuel cell electric bus (FCEB) development in the United States and discuss the achievements and challenges of introducing fuel cell propulsion in transit. This r...

Fuel Cell Buses in U.S. Transit Fleets : Current Status 2012

Science.gov (United States)

2012-11-12

This report is the sixth in an annual series of reports that summarize the progress of fuel cell electric bus (FCEB) development in the United States and discuss the achievements and challenges of introducing fuel cell propulsion in transit. The repo...

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2011

Science.gov (United States)

2011-11-11

his report is the fifth in a series of annual status reports that summarize the progress resulting from fuel cell transit bus demonstrations in the United States and provide a discussion of the achievements and challenges of fuel cell propulsion in t...

Progress in hydrogen fueled busses

International Nuclear Information System (INIS)

Scott, P.B.; Mazaika, D.M.; Tyler, T.

2004-01-01

'Full text:' The Thor/ISE fuel cell bus has been in demonstration and revenue service during 2002-2003 at sites including SunLine Transit, Chula Vista Transit, Los Angeles County Metropolitan Transit Authority, and AC Transit in Oakland. By taking advantage of ISE's advanced hybrid-electric drive technology, this 30-foot bus operates with a much smaller fuel cell than those used in other buses of this class. Further, stress on the fuel cell is diminished. Based on the exceptional performance of this prototype bus, the transit agencies listed above have concluded that hybrid electric hydrogen fueled buses are attractive. Two types of hydrogen fueled hybrid electric buses will be described: - fuel cell powered, and - HICE (Hydrogen Internal Combustion Engine) This progress report will include: 1. Experience with the Thor/ISE fuel cell bus, including results from revenue service at two transit locations, 2. Design and fabrication status of the advanced fuel cell buses being built for AC Transit and SunLine Transit, 3. Design and fabrication status of the prototype HHICE (Hybrid electric Hydrogen fueled Internal Combustion Engine) bus that uses a Ford hydrogen burning engine, mated to a generator, rather than a fuel cell. Other than the engine, the drive train in the HHICE bus is nearly identical to that of a fuel cell hybrid-electric bus. Canadian participation in the HHICE bus is extensive, it is a New Flyer platform and will be winter tested in Winnipeg. (author)

SunLine Transit Agency Fuel Cell Transit Bus: Fourth Evaluation Report (Report and Appendices)

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2009-01-01

This report describes operations at SunLine Transit Agency for a prototype fuel cell bus and five new compressed natural gas (CNG) buses. This is the fourth evaluation report for this site, and it describes results and experiences from April 2008 through October 2008. These results are an addition to those provided in the previous three evaluation reports.

SunLine Transit Agency Fuel Cell Transit Bus: Fifth Evaluation Report (Report and Appendices)

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2009-08-01

This report describes operations at SunLine Transit Agency for a prototype fuel cell bus and five compressed natural gas (CNG) buses. This is the fifth evaluation report for this site, and it describes results and experiences from October 2008 through June 2009. These results are an addition to those provided in the previous four evaluation reports.

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration Results. Fourth Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2015-07-02

This report presents results of a demonstration of fuel cell electric buses (FCEB) operating in Oakland, California. Alameda-Contra Costa Transit District (AC Transit) leads the Zero Emission Bay Area (ZEBA) demonstration, which includes 12 advanced-design fuel cell buses and two hydrogen fueling stations. The FCEBs in service at AC Transit are 40-foot, low-floor buses built by Van Hool with a hybrid electric propulsion system that includes a US Hybrid fuel cell power system and EnerDel lithium-based energy storage system. The buses began revenue service in May 2010.

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2012

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Chandler, Kevin [Battelle, Columbus, OH (United States); Gikakis, Christina [Federal Transit Administration, Washington, DC (United States)

2012-11-01

This report is the sixth in an annual series of reports that summarize the progress of fuel cell electric bus (FCEB) development in the United States and discuss the achievements and challenges of introducing fuel cell propulsion in transit. The report also provides a snapshot of current FCEB performance results over the last year.

Towards sustainable urban transportation: Test, demonstration and development of fuel cell and hybrid-electric buses

International Nuclear Information System (INIS)

Folkesson, Anders

2008-05-01

Several aspects make today's transport system non-sustainable: - Production, transport and combustion of fossil fuels lead to global and local environmental problems. - Oil dependency in the transport sector may lead to economical and political instability. - Air pollution, noise, congestion and land-use may jeopardise public health and quality of life, especially in urban areas. In a sustainable urban transport system most trips are made with public transport because high convenience and comfort makes travelling with public transport attractive. In terms of emissions, including noise, the vehicles are environmentally sustainable, locally as well as globally. Vehicles are energy-efficient and the primary energy stems from renewable sources. Costs are reasonable for all involved, from passengers, bus operators and transport authorities to vehicle manufacturers. The system is thus commercially viable on its own merits. This thesis presents the results from three projects involving different concept buses, all with different powertrains. The first two projects included technical evaluations, including tests, of two different fuel cell buses. The third project focussed on development of a series hybrid-bus with internal combustion engine intended for production around 2010. The research on the fuel cell buses included evaluations of the energy efficiency improvement potential using energy mapping and vehicle simulations. Attitudes to hydrogen fuel cell buses among passengers, bus drivers and bus operators were investigated. Safety aspects of hydrogen as a vehicle fuel were analysed and the use of hydrogen compared to electrical energy storage were also investigated. One main conclusion is that a city bus should be considered as one energy system, because auxiliaries contribute largely to the energy use. Focussing only on the powertrain is not sufficient. The importance of mitigating losses far down an energy conversion chain is emphasised. The Scania hybrid fuel cell

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2012

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chander, K.; Gikakis, C.

2012-11-01

This report is the sixth in an annual series of reports that summarize the progress of fuel cell electric bus (FCEB) development in the United States and discuss the achievements and challenges of introducing fuel cell propulsion in transit. The report also provides a snapshot of current FCEB performance results over the last year. There are 25 active FCEBs in demonstrations this year at eight locations.

Clean air program : design guidelines for bus transit systems using electric and hybrid electric propulsion as an alternative fuel

Science.gov (United States)

2003-03-01

The use of alternative fuels to power transit buses is steadily increasing. Several fuels, including : Compressed Natural Gas (CNG), Liquefied Natural Gas (LNG), Liquefied Petroleum Gas (LPG), and : Methanol/Ethanol, are already being used. At presen...

Alternative fuel buses currently in use in China: Life-cycle fossil energy use, GHG emissions and policy recommendations

International Nuclear Information System (INIS)

Ou Xunmin; Zhang Xiliang; Chang Shiyan

2010-01-01

The Chinese government has enacted policies to promote alternative vehicle fuels (AVFs) and alternative fuel vehicles (AFVs), including city bus fleets. The life cycle (LC), energy savings (ES) and GHG reduction (GR) profiles of AVFs/AFVs are critical to those policy decisions. The well-to-wheels module of the Tsinghua-CA3EM model is employed to investigate actual performance data. Compared with conventional buses, AFVs offer differences in performance in terms of both ES and GR. Only half of the AFVs analyzed demonstrate dual benefits. However, all non-oil/gas pathways can substitute oil/gas with coal. Current policies seek to promote technology improvements and market creation initiatives within the guiding framework of national-level diversification and district-level uniformity. Combined with their actual LC behavior and in keeping with near- and long-term strategies, integrated policies should seek to (1) apply hybrid electric technology to diesel buses; (2) encourage NG/LPG buses in gas-abundant cities; (3) promote commercialize electric buses or plug-in capable vehicles through battery technology innovation; (4) support fuel cell buses and hydrogen technology R and D for future potential applications; and (5) conduct further research on boosting vehicle fuel efficiency, applying low-carbon transportation technologies, and addressing all resultant implications of coal-based transportation solutions to human health and natural resources.

Alternative fuel buses currently in use in China: Life-cycle fossil energy use, GHG emissions and policy recommendations

Energy Technology Data Exchange (ETDEWEB)

Ou Xunmin, E-mail: oxm07@mails.tsinghua.edu.c [School of Public Policy and Management (SPPM), Tsinghua University, Beijing 100084 (China); China Automotive Energy Research Center (CAERC), Tsinghua University, Beijing 100084 (China); Institute of Energy, Environment and Economy (3E), Tsinghua University, Beijing 100084 (China); Zhang Xiliang, E-mail: zhang_xl@tsinghua.edu.c [China Automotive Energy Research Center (CAERC), Tsinghua University, Beijing 100084 (China); Institute of Energy, Environment and Economy (3E), Tsinghua University, Beijing 100084 (China); Chang Shiyan [China Automotive Energy Research Center (CAERC), Tsinghua University, Beijing 100084 (China); Institute of Energy, Environment and Economy (3E), Tsinghua University, Beijing 100084 (China)

2010-01-15

The Chinese government has enacted policies to promote alternative vehicle fuels (AVFs) and alternative fuel vehicles (AFVs), including city bus fleets. The life cycle (LC), energy savings (ES) and GHG reduction (GR) profiles of AVFs/AFVs are critical to those policy decisions. The well-to-wheels module of the Tsinghua-CA3EM model is employed to investigate actual performance data. Compared with conventional buses, AFVs offer differences in performance in terms of both ES and GR. Only half of the AFVs analyzed demonstrate dual benefits. However, all non-oil/gas pathways can substitute oil/gas with coal. Current policies seek to promote technology improvements and market creation initiatives within the guiding framework of national-level diversification and district-level uniformity. Combined with their actual LC behavior and in keeping with near- and long-term strategies, integrated policies should seek to (1) apply hybrid electric technology to diesel buses; (2) encourage NG/LPG buses in gas-abundant cities; (3) promote commercialize electric buses or plug-in capable vehicles through battery technology innovation; (4) support fuel cell buses and hydrogen technology R and D for future potential applications; and (5) conduct further research on boosting vehicle fuel efficiency, applying low-carbon transportation technologies, and addressing all resultant implications of coal-based transportation solutions to human health and natural resources.

Alternative fuel buses currently in use in China. Life-cycle fossil energy use, GHG emissions and policy recommendations

Energy Technology Data Exchange (ETDEWEB)

Ou, Xunmin [School of Public Policy and Management (SPPM), Tsinghua University, Beijing 100084 (China); China Automotive Energy Research Center (CAERC), Tsinghua University, Beijing 100084 (China); Institute of Energy, Environment and Economy (3E), Tsinghua University, Beijing 100084 (China); Zhang, Xiliang; Chang, Shiyan [China Automotive Energy Research Center (CAERC), Tsinghua University, Beijing 100084 (China); Institute of Energy, Environment and Economy (3E), Tsinghua University, Beijing 100084 (China)

2010-01-15

The Chinese government has enacted policies to promote alternative vehicle fuels (AVFs) and alternative fuel vehicles (AFVs), including city bus fleets. The life cycle (LC), energy savings (ES) and GHG reduction (GR) profiles of AVFs/AFVs are critical to those policy decisions. The well-to-wheels module of the Tsinghua-CA3EM model is employed to investigate actual performance data. Compared with conventional buses, AFVs offer differences in performance in terms of both ES and GR. Only half of the AFVs analyzed demonstrate dual benefits. However, all non-oil/gas pathways can substitute oil/gas with coal. Current policies seek to promote technology improvements and market creation initiatives within the guiding framework of national-level diversification and district-level uniformity. Combined with their actual LC behavior and in keeping with near- and long-term strategies, integrated policies should seek to (1) apply hybrid electric technology to diesel buses; (2) encourage NG/LPG buses in gas-abundant cities; (3) promote commercialize electric buses or plug-in capable vehicles through battery technology innovation; (4) support fuel cell buses and hydrogen technology R and D for future potential applications; and (5) conduct further research on boosting vehicle fuel efficiency, applying low-carbon transportation technologies, and addressing all resultant implications of coal-based transportation solutions to human health and natural resources. (author)

Alternative Fuel News, Volume 4, Number 3

Energy Technology Data Exchange (ETDEWEB)

Ficker, C.

2000-11-14

This issue of Alternative Fuel News focuses on transit buses and refuse haulers. Many transit agencies and waste management companies are investigating alternatives to traditional diesel buses and refuse haulers.

Buses retrofitting with diesel particle filters: Real-world fuel economy and roadworthiness test considerations.

Science.gov (United States)

Fleischman, Rafael; Amiel, Ran; Czerwinski, Jan; Mayer, Andreas; Tartakovsky, Leonid

2018-05-01

Retrofitting older vehicles with diesel particulate filter (DPF) is a cost-effective measure to quickly and efficiently reduce particulate matter emissions. This study experimentally analyzes real-world performance of buses retrofitted with CRT DPFs. 18 in-use Euro III technology urban and intercity buses were investigated for a period of 12months. The influence of the DPF and of the vehicle natural aging on buses fuel economy are analyzed and discussed. While the effect of natural deterioration is about 1.2%-1.3%, DPF contribution to fuel economy penalty is found to be 0.6% to 1.8%, depending on the bus type. DPF filtration efficiency is analyzed throughout the study and found to be in average 96% in the size range of 23-560nm. Four different load and non-load engine operating modes are investigated on their appropriateness for roadworthiness tests. High idle is found to be the most suitable regime for PN diagnostics considering particle number filtration efficiency. Copyright © 2017. Published by Elsevier B.V.

The Fuel Economy of Hybrid Buses: The Role of Ancillaries in Real Urban Driving

Directory of Open Access Journals (Sweden)

Francesco Bottiglione

2014-07-01

Full Text Available In the present context of the global economic crisis and environmental emergency, transport science is asked to find innovative solutions to turn traditional vehicles into fuel-saving and eco-friendly devices. In the last few years, hybrid vehicles have been shown to have potential benefits in this sense. In this paper, the fuel economy of series hybrid-electric and hybrid-mechanical buses is simulated in two real driving situations: cold and hot weather driving in the city of Taranto, in Southern Italy. The numerical analysis is carried out by an inverse dynamic approach, where the bus speed is given as a velocity pattern measured in the field tests performed on one of the city bus routes. The city of Taranto drive schedule is simulated in a typical tempered climate condition and with a hot temperature, when the air conditioning system must be switched on for passenger comfort. The fuel consumptions of hybrid-electric and hybrid-mechanical buses are compared to each other and with a traditional bus powered by a diesel engine. It is shown that the series hybrid-electric vehicle outperforms both the traditional and the mechanical hybrid vehicles in the cold weather driving simulation, reducing the fuel consumption by about 35% with respect to the traditional diesel bus. However, it is also shown that the performance of the hybrid-electric bus gets dramatically worse when the air-cooling system is continuously turned on. In this situation, the fuel consumption of the three different technologies for city buses under investigation is comparable.

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration Results: Fifth Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jeffers, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-06-01

This report presents results of a demonstration of fuel cell electric buses (FCEB) operating in Oakland, California. Alameda-Contra Costa Transit District (AC Transit) leads the Zero Emission Bay Area (ZEBA) demonstration, which includes 13 advanced-design fuel cell buses and two hydrogen fueling stations. The ZEBA partners are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service. NREL has published four previous reports describing operation of these buses. This report presents new and updated results covering data from January 2015 through December 2015.

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration Results: Sixth Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Post, Matthew B. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jeffers, Matthew A. [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-11

This report presents results of a demonstration of fuel cell electric buses (FCEB) operating in Oakland, California. Alameda-Contra Costa Transit District (AC Transit) leads the Zero Emission Bay Area (ZEBA) demonstration, which includes 13 advanced-design fuel cell buses and two hydrogen fueling stations. The ZEBA partners are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service. NREL has published five previous reports describing operation of these buses. This report presents new and updated results covering data from January 2016 through December 2016.

Emissions of toxic pollutants from compressed natural gas and low sulfur diesel-fueled heavy-duty transit buses tested over multiple driving cycles.

Science.gov (United States)

Kado, Norman Y; Okamoto, Robert A; Kuzmicky, Paul A; Kobayashi, Reiko; Ayala, Alberto; Gebel, Michael E; Rieger, Paul L; Maddox, Christine; Zafonte, Leo

2005-10-01

The number of heavy-duty vehicles using alternative fuels such as compressed natural gas (CNG) and new low-sulfur diesel fuel formulations and equipped with after-treatment devices are projected to increase. However, few peer-reviewed studies have characterized the emissions of particulate matter (PM) and other toxic compounds from these vehicles. In this study, chemical and biological analyses were used to characterize the identifiable toxic air pollutants emitted from both CNG and low-sulfur-diesel-fueled heavy-duty transit buses tested on a chassis dynamometer over three transient driving cycles and a steady-state cruise condition. The CNG bus had no after-treatment, and the diesel bus was tested first equipped with an oxidation catalyst (OC) and then with a catalyzed diesel particulate filter (DPF). Emissions were analyzed for PM, volatile organic compounds (VOCs; determined on-site), polycyclic aromatic hydrocarbons (PAHs), and mutagenic activity. The 2000 model year CNG-fueled vehicle had the highest emissions of 1,3-butadiene, benzene, and carbonyls (e.g., formaldehyde) of the three vehicle configurations tested in this study. The 1998 model year diesel bus equipped with an OC and fueled with low-sulfur diesel had the highest emission rates of PM and PAHs. The highest specific mutagenic activities (revertants/microg PM, or potency) and the highest mutagen emission rates (revertants/mi) were from the CNG bus in strain TA98 tested over the New York Bus (NYB) driving cycle. The 1998 model year diesel bus with DPF had the lowest VOCs, PAH, and mutagenic activity emission. In general, the NYB driving cycle had the highest emission rates (g/mi), and the Urban Dynamometer Driving Schedule (UDDS) had the lowest emission rates for all toxics tested over the three transient test cycles investigated. Also, transient emissions were, in general, higher than steady-state emissions. The emissions of toxic compounds from an in-use CNG transit bus (without an oxidation

Electric buses - An energy efficient urban transportation means

Energy Technology Data Exchange (ETDEWEB)

Kuehne, Reinhart [German Aerospace Center (DLR), Transportation Studies, Rutherfordstr. 2, 12489 Berlin (Germany)

2010-12-15

Bus transit systems with electric traction are an important contribution to the post fossil fuel mobility. Most renewable energy sources provide energy in the form of electricity. Electric motors thus have promise in the development of the way ''beyond oil''. The reactivation of trolley bus systems - grid bounded but also catenary free for short distances - paves this way. The design of modern trolley bus operations overcomes the existing disadvantages of conventional buses using fossil fuel. Germany has an efficient industry in this field, that offers braking energy recovery and energy storage in modern supercapacitors as well as technical and organisational innovations for a local emission free and a low noise transit system. Gentle but powerful when starting and braking, the trolley bus is cost effective and easy to integrate into an existing infrastructure. Such an electric bus system is ecological, customer-friendly and suitable for cities. It has a high economic efficiency and it also expands the traffic planning field towards an ecological future technology. This paper shows examples at home and abroad how electric buses achieve an energy solving modern urban traffic. It gives insights into technical developments of electric vehicle equipment, cateneries with fast driving handling characteristics and the use of plain electric and hybrid powertrains. (author)

Lagrangian Hotspots of In-Use NOX Emissions from Transit Buses.

Science.gov (United States)

Kotz, Andrew J; Kittelson, David B; Northrop, William F

2016-06-07

In-use, spatiotemporal NOX emissions were measured from a conventional powertrain transit bus and a series electric hybrid bus over gradients of route kinetic intensity and ambient temperature. This paper introduces a new method for identifying NOX emissions hotspots along a bus route using high fidelity Lagrangian vehicle data to explore spatial interactions that may influence emissions production. Our study shows that the studied transit buses emit higher than regulated emissions because on-route operation does not accurately represent the range of engine operation tested according to regulatory standards. Using the Lagrangian hotspot detection, we demonstrate that NOX hotspots occurred at bus stops, during cold starts, on inclines, and for accelerations. On the selected routes, bus stops resulted in 3.3 times the route averaged emissions factor in grams/km without significant dependence on bus type or climate. The buses also emitted 2.3 times the route averaged NOX emissions factor at the beginning of each route due to cold selective catalytic reduction aftertreatment temperature. The Lagrangian hotspot detection technique demonstrated here could be employed in future connected vehicles empowered by advances in computational power, data storage capability, and improved sensor technology to optimize emissions as a function of spatial location.

Multi-criteria analysis of alternative-fuel buses for public transportation

International Nuclear Information System (INIS)

Tzeng, G.-H.; Lin, C.-W.; Opricovic, Serafim

2005-01-01

The technological development of buses with new alternative fuels is considered in this paper. Several types of fuels are considered as alternative-fuel modes, i.e., electricity, fuel cell (hydrogen), and methanol. Electric vehicles may be considered the alternative-fuel vehicles with the lowest air pollution. Hybrid electric vehicles provide an alternate mode, at least for the period of improving the technology of electric vehicles. A hybrid electric vehicle is defined as a vehicle with the conventional internal combustion engine and an electric motor as its major sources of power. Experts from different decision-making groups performed the multiple attribute evaluation of alternative vehicles. AHP is applied to determine the relative weights of evaluation criteria. TOPSIS and VIKOR are compared and applied to determine the best compromise alternative fuel mode. The result shows that the hybrid electric bus is the most suitable substitute bus for Taiwan urban areas in the short and median term. But, if the cruising distance of the electric bus extends to an acceptable range, the pure electric bus could be the best alternative

Alternative Fuels for Washington's School Buses: A Report to the Washington State Legislature.

Science.gov (United States)

Lyons, John Kim; McCoy, Gilbert A.

This document presents findings of a study that evaluated the use of both propane and compressed natural gas as alternative fuels for Washington State school buses. It discusses air quality improvement actions by state- and federal-level regulators and summarizes vehicle design, development, and commercialization activities by all major engine,…

American Fuel Cell Bus Project Evaluation. Second Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2015-09-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Administration's (FTA's) National Fuel Cell Bus Program. Through the non-profit consortia CALSTART, a team led by SunLine Transit Agency and BAE Systems developed a new fuel cell electric bus for demonstration. SunLine added two more AFCBs to its fleet in 2014 and another in 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report summarizes the performance results for the buses through June 2015.

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: First Results Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2011-03-01

This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This report provides the early data results and implementation experience of the AT fuel cell bus since it was placed in service.

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Fourth Results Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2013-01-01

SunLine Transit Agency, which provides public transit services to the Coachella Valley area of California, has demonstrated hydrogen and fuel cell bus technologies for more than 10 years. In May 2010, SunLine began demonstrating the advanced technology (AT) fuel cell bus with a hybrid electric propulsion system, fuel cell power system, and lithium-based hybrid batteries. This report describes operations at SunLine for the AT fuel cell bus and five compressed natural gas buses. The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) is working with SunLine to evaluate the bus in real-world service to document the results and help determine the progress toward technology readiness. NREL has previously published three reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from February 2012 through November 2012.

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Third Results Reports

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2012-05-01

This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. NREL has previously published two reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from July 2011 through January 2012.

Real-world emissions and fuel consumption of diesel buses and trucks in Macao: From on-road measurement to policy implications

Science.gov (United States)

Wu, Xiaomeng; Zhang, Shaojun; Wu, Ye; Li, Zhenhua; Zhou, Yu; Fu, Lixin; Hao, Jiming

2015-11-01

A total of 13 diesel buses and 12 diesel trucks in Macao were tested using portable emission measurement systems (PEMS) including a SEMTECH-DS for gaseous emissions and a SEMTECH-PPMD for PM2.5. The average emission rates of gaseous pollutants and CO2 are developed with the operating mode defined by the instantaneous vehicle specific power (VSP) and vehicle speed. Both distance-based and fuel mass-based emission factors for gaseous pollutants (e.g., CO, THC and NOX) are further estimated under typical driving conditions. The average distance-based NOX emission of heavy-duty buses (HDBs) is higher than 13 g km-1. Considering the unfavorable conditions for selective reductions catalyst (SCR) systems, such as low-speed driving conditions, more effective technology options (e.g., dedicated natural gas buses and electric buses) should be considered by policy makers in Macao. We identified strong effects of the vehicle size, engine displacement and driving conditions on real-world CO2 emission factors and fuel consumption for diesel vehicles. Therefore, detailed profiles regarding vehicle specifications can reduce the uncertainty in their fleet-average on-road fuel consumption. In addition, strong correlations between relative emission factors and driving conditions indicated by the average speed of generated micro-trips are identified based on a micro-trip method. For example, distance-based emission factors of HDBs will increase by 39% for CO, 29% for THC, 43% for NOX and 26% for CO2 when the average speed decreases from 30 km h-1 to 20 km h-1. The mitigation of on-road emissions from diesel buses and trucks by improving traffic conditions through effective traffic and economic management measures is therefore required. This study demonstrates the important role of PEMS in understanding vehicle emissions and mitigation strategies from science to policy perspectives.

Adopting Clean Fuels and Technologies on School Buses. Pollution and Health Impacts in Children.

Science.gov (United States)

Adar, Sara D; D'Souza, Jennifer; Sheppard, Lianne; Kaufman, Joel D; Hallstrand, Teal S; Davey, Mark E; Sullivan, James R; Jahnke, Jordan; Koenig, Jane; Larson, Timothy V; Liu, L J Sally

2015-06-15

More than 25 million American children breathe polluted air on diesel school buses. Emission reduction policies exist, but the health impacts to individual children have not been evaluated. Using a natural experiment, we characterized the exposures and health of 275 school bus riders before, during, and after the adoption of clean technologies and fuels between 2005 and 2009. Air pollution was measured during 597 trips on 188 school buses. Repeated measures of exhaled nitric oxide (FeNO), lung function (FEV1, FVC), and absenteeism were also collected monthly (1,768 visits). Mixed-effects models longitudinally related the adoption of diesel oxidation catalysts (DOCs), closed crankcase ventilation systems (CCVs), ultralow-sulfur diesel (ULSD), or biodiesel with exposures and health. Fine and ultrafine particle concentrations were 10-50% lower on buses using ULSD, DOCs, and/or CCVs. ULSD adoption was also associated with reduced FeNO (-16% [95% confidence interval (CI), -21 to -10%]), greater changes in FVC and FEV1 (0.02 [95% CI, 0.003 to 0.05] and 0.01 [95% CI, -0.006 to 0.03] L/yr, respectively), and lower absenteeism (-8% [95% CI, -16.0 to -0.7%]), with stronger associations among patients with asthma. DOCs, and to a lesser extent CCVs, also were associated with improved FeNO, FVC growth, and absenteeism, but these findings were primarily restricted to patients with persistent asthma and were often sensitive to control for ULSD. No health benefits were noted for biodiesel. Extrapolating to the U.S. population, changed fuel/technologies likely reduced absenteeism by more than 14 million/yr. National and local diesel policies appear to have reduced children's exposures and improved health.

Microbial air quality in mass transport buses and work-related illness among bus drivers of Bangkok Mass Transit Authority.

Science.gov (United States)

Luksamijarulkul, Pipat; Sundhiyodhin, Viboonsri; Luksamijarulkul, Soavalug; Kaewboonchoo, Orawan

2004-06-01

The air quality in mass transport buses, especially air-conditioned buses may affect bus drivers who work full time. Bus numbers 16, 63, 67 and 166 of the Seventh Bus Zone of Bangkok Mass Transit Authority were randomly selected to investigate for microbial air quality. Nine air-conditioned buses and 2-4 open-air buses for each number of the bus (36 air-conditioned buses and 12 open-air buses) were included. Five points of in-bus air samples in each studied bus were collected by using the Millipore A ir Tester Totally, 180 and 60 air samples collected from air-conditioned buses and open-air buses were cultured for bacterial and fungal counts. The bus drivers who drove the studied buses were interviewed towards histories of work-related illness while working. The results revealed that the mean +/- SD of bacterial counts in the studied open-air buses ranged from 358.50 +/- 146.66 CFU/m3 to 506 +/- 137.62 CFU/m3; bus number 16 had the highest level. As well as the mean +/- SD of fungal counts which ranged from 93.33 +/- 44.83 CFU/m3 to 302 +/- 294.65 CFU/m3; bus number 166 had the highest level. Whereas, the mean +/- SD of bacterial counts in the studied air-conditioned buses ranged from 115.24 +/- 136.01 CFU/m3 to 244.69 +/- 234.85 CFU/m3; bus numbers 16 and 67 had the highest level. As well as the mean +/- SD of fungal counts which rangedfrom 18.84 +/- 39.42 CFU/m3 to 96.13 +/- 234.76 CFU/m3; bus number 166 had the highest level. When 180 and 60 studied air samples were analyzed in detail, it was found that 33.33% of the air samples from open-air buses and 6.11% of air samples from air-conditioned buses had a high level of bacterial counts (> 500 CFU/m3) while 6.67% of air samples from open-air buses and 2.78% of air samples from air-conditioned buses had a high level of fungal counts (> 500 CFU/m3). Data from the history of work-related illnesses among the studied bus drivers showed that 91.67% of open-air bus drivers and 57.28% of air-conditioned bus drivers had

Safety evaluation of a hydrogen fueled transit bus

Energy Technology Data Exchange (ETDEWEB)

Coutts, D.A.; Thomas, J.K.; Hovis, G.L.; Wu, T.T. [Westinghouse Savannah River Co., Aiken, SC (United States)

1997-12-31

Hydrogen fueled vehicle demonstration projects must satisfy management and regulator safety expectations. This is often accomplished using hazard and safety analyses. Such an analysis has been completed to evaluate the safety of the H2Fuel bus to be operated in Augusta, Georgia. The evaluation methods and criteria used reflect the Department of Energy`s graded approach for qualifying and documenting nuclear and chemical facility safety. The work focused on the storage and distribution of hydrogen as the bus motor fuel with emphases on the technical and operational aspects of using metal hydride beds to store hydrogen. The safety evaluation demonstrated that the operation of the H2Fuel bus represents a moderate risk. This is the same risk level determined for operation of conventionally powered transit buses in the United States. By the same criteria, private passenger automobile travel in the United States is considered a high risk. The evaluation also identified several design and operational modifications that resulted in improved safety, operability, and reliability. The hazard assessment methodology used in this project has widespread applicability to other innovative operations and systems, and the techniques can serve as a template for other similar projects.

Diesel vs. compressed natural gas for school buses: a cost-effectiveness evaluation of alternative fuels

International Nuclear Information System (INIS)

Cohen, J.T.

2005-01-01

Reducing emissions from school buses is a priority for both state and federal regulators. Two popular alternative technologies to conventional diesel (CD) are emission controlled diesel (ECD), defined here to be diesel buses equipped with continuously regenerating particle filters, and engines fueled by compressed natural gas (CNG). This paper uses a previously published model to quantify the impact of particulate matter (PM), oxides of nitrogen (NO x ), and sulfur dioxide (SO 2 ) emissions on population exposure to ozone and to primary and secondary PM, and to quantify the resulting health damages, expressed in terms of lost quality adjusted life years (QALYs). Resource costs include damages from greenhouse gas-induced climate change, vehicle procurement, infrastructure development, and operations. I find that ECD and CNG produce very similar reductions in health damages compared to CD, although CNG has a modest edge because it may have lower NO x emissions. However, ECD is far more cost effective ($400,000-900,000 cost per QALY saved) than CNG (around $4 million per QALY saved). The results are uncertain because the model used makes a series of simplifying assumptions and because emissions data and cost data for school buses are very limited

Gas Phase Emission Ratios From In-Use Diesel and CNG Curbside Passenger Buses in New York City

Science.gov (United States)

Herndon, S. C.; Shorter, J.; Canagaratna, M.; Jayne, J.; Nelson, D. D.; Wormhoudt, J. C.; Williams, P.; Silva, P. J.; Shi, Q.; Ghertner, A.; Zahniser, M.; Worsnop, D.; Kolb, C.; Lanni, T.; Drewnick, F.; Demerjian, K. L.

2002-12-01

The Aerodyne Mobile Laboratory simultaneously measured gas phase and particulate emissions from in use vehicles during two campaigns in New York City. The campaigns took place during two weeks in October, 2000 and four weeks in July-August, 2001. Passenger curbside buses were the primary focus of the study, but school buses and several other heavy duty diesel vehicles were also characterized. This paper describes the methodologies used to measure individual in use vehicles and presents the results of the gas phase measurements. Emission ratios for NO, NO2, SO2, N2O, CO, CH4 and H2CO relative to CO2 have been determined across several classes of buses. The gas phase concentrations were measured each second, using Tunable Infrared Laser Direct Absorption Spectroscopy (TILDAS). Some of the categories of buses into which the data has been sorted are; diesel (both 6V92 and Series 50) with and without the Continuous Regenerative Technology (CRT) retrofit, compressed natural gas powered(CNG) and hybrid diesel-electric buses. The New York Metropolitan Transit Authority (MTA) cooperated with this work, providing details about each of their buses followed. In addition to MTA buses, other New York City passenger bus operators were also measured. In September 2000, MTA began to switch to 30 ppm sulfur diesel fuel while it is believed the non MTA operators did not. The measured emission ratios show that low sulfur fuel greatly reduces the amount of SO2 per CO2. Roughly one third of the MTA fleet of diesel buses have been equipped with the CRT retrofit. The gas phase results of interest in this category show increased direct emission of NO2 and companion work (also submitted to the 12th CRC) show the impact the CRT refit has on particulate emissions. CNG buses show increased H2CO and CH4 emission ratios relative to diesel powered motors.

Adopting Clean Fuels and Technologies on School Buses. Pollution and Health Impacts in Children

Science.gov (United States)

D’Souza, Jennifer; Sheppard, Lianne; Kaufman, Joel D.; Hallstrand, Teal S.; Davey, Mark E.; Sullivan, James R.; Jahnke, Jordan; Koenig, Jane; Larson, Timothy V.; Liu, L. J. Sally

2015-01-01

Rationale: More than 25 million American children breathe polluted air on diesel school buses. Emission reduction policies exist, but the health impacts to individual children have not been evaluated. Methods: Using a natural experiment, we characterized the exposures and health of 275 school bus riders before, during, and after the adoption of clean technologies and fuels between 2005 and 2009. Air pollution was measured during 597 trips on 188 school buses. Repeated measures of exhaled nitric oxide (FeNO), lung function (FEV1, FVC), and absenteeism were also collected monthly (1,768 visits). Mixed-effects models longitudinally related the adoption of diesel oxidation catalysts (DOCs), closed crankcase ventilation systems (CCVs), ultralow-sulfur diesel (ULSD), or biodiesel with exposures and health. Measurements and Main Results: Fine and ultrafine particle concentrations were 10–50% lower on buses using ULSD, DOCs, and/or CCVs. ULSD adoption was also associated with reduced FeNO (−16% [95% confidence interval (CI), −21 to −10%]), greater changes in FVC and FEV1 (0.02 [95% CI, 0.003 to 0.05] and 0.01 [95% CI, −0.006 to 0.03] L/yr, respectively), and lower absenteeism (−8% [95% CI, −16.0 to −0.7%]), with stronger associations among patients with asthma. DOCs, and to a lesser extent CCVs, also were associated with improved FeNO, FVC growth, and absenteeism, but these findings were primarily restricted to patients with persistent asthma and were often sensitive to control for ULSD. No health benefits were noted for biodiesel. Extrapolating to the U.S. population, changed fuel/technologies likely reduced absenteeism by more than 14 million/yr. Conclusions: National and local diesel policies appear to have reduced children’s exposures and improved health. PMID:25867003

Modeling transit bus fuel consumption on the basis of cycle properties.

Science.gov (United States)

Delgado, Oscar F; Clark, Nigel N; Thompson, Gregory J

2011-04-01

A method exists to predict heavy-duty vehicle fuel economy and emissions over an "unseen" cycle or during unseen on-road activity on the basis of fuel consumption and emissions data from measured chassis dynamometer test cycles and properties (statistical parameters) of those cycles. No regression is required for the method, which relies solely on the linear association of vehicle performance with cycle properties. This method has been advanced and examined using previously published heavy-duty truck data gathered using the West Virginia University heavy-duty chassis dynamometer with the trucks exercised over limited test cycles. In this study, data were available from a Washington Metropolitan Area Transit Authority emission testing program conducted in 2006. Chassis dynamometer data from two conventional diesel buses, two compressed natural gas buses, and one hybrid diesel bus were evaluated using an expanded driving cycle set of 16 or 17 different driving cycles. Cycle properties and vehicle fuel consumption measurements from three baseline cycles were selected to generate a linear model and then to predict unseen fuel consumption over the remaining 13 or 14 cycles. Average velocity, average positive acceleration, and number of stops per distance were found to be the desired cycle properties for use in the model. The methodology allowed for the prediction of fuel consumption with an average error of 8.5% from vehicles operating on a diverse set of chassis dynamometer cycles on the basis of relatively few experimental measurements. It was found that the data used for prediction should be acquired from a set that must include an idle cycle along with a relatively slow transient cycle and a relatively high speed cycle. The method was also applied to oxides of nitrogen prediction and was found to have less predictive capability than for fuel consumption with an average error of 20.4%.

Tracking costs of alternatively fueled buses in Florida : [summary].

Science.gov (United States)

2011-01-01

In an effort to address rising fuel costs and environmental concerns, many transit agencies across Florida have introduced alternative fuel technologies to their traditional diesel-powered fleets. Fuel types include biodiesel, compressed natural gas,...

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration: First Results Report

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2011-08-01

This report documents the early implementation experience for the Zero Emission Bay Area (ZEBA) Demonstration, the largest fleet of fuel cell buses in the United States. The ZEBA Demonstration group includes five participating transit agencies: AC Transit (lead transit agency), Santa Clara Valley Transportation Authority (VTA), Golden Gate Transit (GGT), San Mateo County Transit District (SamTrans), and San Francisco Municipal Railway (Muni). The ZEBA partners are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service.

COMPARATIVE STUDY ON EXHAUST EMISSIONS FROM DIESEL- AND CNG-POWERED URBAN BUSES

Energy Technology Data Exchange (ETDEWEB)

COROLLER, P; PLASSAT, G

2003-08-24

Couple years ago, ADEME engaged programs dedicated to the urban buses exhaust emissions studies. The measures associated with the reduction of atmospheric and noise pollution has particular importance in the sector of urban buses. In many cases, they illustrate the city's environmental image and contribute to reinforcing the attractiveness of public transport. France's fleet in service, presently put at about 14,000 units, consumes about 2 per cent of the total energy of city transport. It causes about 2 per cent of the HC emissions and from 4 to 6 per cent of the NOx emissions and particles. These vehicles typically have a long life span (about 15 years) and are relatively expensive to buy, about 150.000 euros per unit. Several technical solutions were evaluated to quantify, on a real condition cycle for buses, on one hand pollutants emissions, fuel consumption and on the other hand reliability, cost in real existing fleet. This paper presents main preliminary results on urban buses exhaust emission on two different cases: - existing Diesel buses, with fuel modifications (Diesel with low sulphur content), Diesel with water emulsion and bio-Diesel (30% oil ester in standard Diesel fuel); renovating CNG powered Euro II buses fleet, over representative driving cycles, set up by ADEME and partners. On these cycles, pollutants (regulated and unregulated) were measured as well as fuel consumption, at the beginning of a program and one year after to quantify reliability and increase/decrease of pollutants emissions. At the same time, some after-treatment technologies were tested under real conditions and several vehicles. Information such as fuel consumption, lubricant analysis, problem on the technology were following during a one year program. On the overall level, it is the combination of various action, pollution-reduction and renewal that will make it possible to meet the technological challenge of reducing emissions and fuel consumption by urban bus

Environmental benefits of natural gas for buses

International Nuclear Information System (INIS)

Rabl, A.

2002-01-01

This paper presents a life cycle assessment comparing diesel buses with buses fueled by natural gas. The data for the emission of pollutants are based on the MEET Project of the European Commission (EC), supplemented by data measured for diesel and gas buses in Paris. The benefits of the gas fueled bus are then quantified using the damage cost estimates of the ExternE Project of the EC. A diesel bus with emissions equal to Standard EURO2 of the EC is compared with the same bus equipped with a natural gas engine, for use in Paris and in Toulouse. The damage cost of a diesel bus is significant, in the range of 0.4-1.3 euro/km. Natural gas allows an appreciable reduction of the emissions, lowering the damage cost by a factor of about 2.5 (Toulouse) to 5.5 (Paris). An approximate rule is provided for transferring the results to other cities. A sensitivity analysis is carried out to evaluate the effect of the evolution of the emissions standard towards EURO3, 4 and 5, as well as the effect of uncertainties. Finally a comparison is presented between a EURO2 diesel bus with particle filter, and a gas fueled bus with the MPI engine of IVECO, a more advanced and cleaner technology. With this engine the damage costs of the gas fueled bus are about 3-5 times lower than those of the diesel with particle filter, even though the latter has already very low emissions.(author)

Natural gas drive for city buses in Skopje

International Nuclear Information System (INIS)

Dimitrovski, Mile; Veljanovski, Krsto; Dimitrovski, Dame

2002-01-01

Emission improvement in both city centers and conurbations is an important factor which developers of public-utility vehicles and buses must take into account. If natural gas is used as a fuel the emission is considerably lower than that from conventional diesel drive. Thus it is an important contribution to keep the air clean in the area where the vehicles are deployed. In this paper the project 'Ecological Natural gas drive for city buses in Skopje' is analysed. (Original)

The Bus Stops Here: The Case for Biodiesel in School Buses.

Science.gov (United States)

Rao, Steven T.

2002-01-01

Suggests that diesel exhaust from most of the nation's school buses may be hazardous to children's health. Documents studies on the nature and potential magnitude of the risk to children and proposes replacing petroleum diesel with biodiesel as the fuel for school buses. Presents the merits and practicality of switching to biodiesel as a healthier…

Unregulated emissions from compressed natural gas (CNG) transit buses configured with and without oxidation catalyst.

Science.gov (United States)

Okamoto, Robert A; Kado, Norman Y; Kuzmicky, Paul A; Ayala, Alberto; Kobayashi, Reiko

2006-01-01

The unregulated emissions from two in-use heavy-duty transit buses fueled by compressed natural gas (CNG) and equipped with oxidation catalyst (OxiCat) control were evaluated. We tested emissions from a transit bus powered by a 2001 Cummins Westport C Gas Plus 8.3-L engine (CWest), which meets the California Air Resources Board's (CARB) 2002 optional NOx standard (2.0 g/bhp-hr). In California, this engine is certified only with an OxiCat, so our study did not include emissions testing without it. We also tested a 2000 New Flyer 40-passenger low-floor bus powered by a Detroit Diesel series 50G engine (DDCs50G) that is currently certified in California without an OxiCat. The original equipment manufacturer (OEM) offers a "low-emission" package for this bus that includes an OxiCat for transit bus applications, thus, this configuration was also tested in this study. Previously, we reported that formaldehyde and other volatile organic emissions detected in the exhaust of the DDCs50G bus equipped with an OxiCat were significantly reduced relative to the same DDCs50G bus without OxiCat. In this paper, we examine othertoxic unregulated emissions of significance. The specific mutagenic activity of emission sample extracts was examined using the microsuspension assay. The total mutagenic activity of emissions (activity per mile) from the OxiCat-equipped DDC bus was generally lower than that from the DDC bus without the OxiCat. The CWest bus emission samples had mutagenic activity that was comparable to that of the OxiCat-equipped DDC bus. In general, polycyclic aromatic hydrocarbon (PAH) emissions were lower forthe OxiCat-equipped buses, with greater reductions observed for the volatile and semivolatile PAH emissions. Elemental carbon (EC) was detected in the exhaust from the all three bus configurations, and we found that the total carbon (TC) composition of particulate matter (PM) emissions was primarily organic carbon (OC). The amount of carbon emissions far exceeded the

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Second Results Report and Appendices

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2011-10-01

This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This is the second results report for the AT fuel cell bus since it was placed in service, and it focuses on the newest data analysis and lessons learned since the previous report. The appendices, referenced in the main report, provide the full background for the evaluation. They will be updated as new information is collected but will contain the original background material from the first report.

HYDROGEN COMMERCIALIZATION: TRANSPORTATION FUEL FOR THE 21ST CENTURY

Energy Technology Data Exchange (ETDEWEB)

APOLONIO DEL TORO

2008-05-27

Since 1999, SunLine Transit Agency has worked with the U.S. Department of Energy (DOE), U.S. Department of Defense (DOD), and the U.S. Department of Transportation (DOT) to develop and test hydrogen infrastructure, fuel cell buses, a heavy-duty fuel cell truck, a fuel cell neighborhood electric vehicle, fuel cell golf carts and internal combustion engine buses operating on a mixture of hydrogen and compressed natural gas (CNG). SunLine has cultivated a rich history of testing and demonstrating equipment for leading industry manufacturers in a pre-commercial environment. Visitors to SunLine's "Clean Fuels Mall" from around the world have included government delegations and agencies, international journalists and media, industry leaders and experts and environmental and educational groups.

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration Results: Sixth Report

Science.gov (United States)

2017-09-01

This report presents results of a demonstration of fuel cell electric buses (FCEBs) operating in Oakland, California. Alameda-Contra Costa Transit District (AC Transit) leads the Zero Emission Bay Area (ZEBA) demonstration that includes 13 advanced-d...

Development and demonstration of use of methane/hydrogen blends as fuel in existing methane-driven buses; Utveckling och demonstration av anvaendning av metan/vaetgasblandningar som braensle i befintliga metangasdrivna bussar

Energy Technology Data Exchange (ETDEWEB)

Joensson, Owe

2006-10-15

Two natural gas buses in Malmoe have in a project been converted to run on mixtures of hydrogen and natural gas. The buses have been in operation from September 2003 to December 2005 and have during the whole extent of the project been in commercial operation with passengers. One bus has been refuelled with a mixture containing 8% hydrogen and another with 25% hydrogen. One of the buses has during limited periods been refuelled with natural gas in order to establish differences in fuel consumption between the different fuels. A number of different supporting activities have been performed in conjunction to the project: Tests at the Lund Univ. with hydrogen addition to natural gas in a one cylinder test engine and in a 6 cylinder natural gas engine. Safety analysis for handling of hydrogen/natural gas blends. Hydrogen compatibility study of material and components in bus fuel system. Test of leak detection systems for hydrogen and hydrogen/natural gas blends. Development of safety routines for operation and maintenance staff. Emission measurement during road operation with mobile equipment. Follow up of filling station for hydrogen/natural gas blends. The results from the projects are: The buses did not need to be modified in any way in order to run on mixtures with up to 8 vol-% hydrogen. The buses could, in less than 4 h, be modified to run on mixtures with 25 vol-% hydrogen. The conversion was accomplished by changing one computer chip in the engine control system, thus altering the air/fuel ratio and adjusting the ignition angle. The fuel consumption of the buses was reduced by 20-30% by hydrogen addition. The largest relative influence was achieved with 8% hydrogen addition. The reduced fuel consumption in combination with reduced carbon content in the fuel resulted in a total reduction in CO{sub 2}-emission by approximately 35% using 8% hydrogen (by volume). Addition of hydrogen to natural gas has thus proved to be a more efficient way of reducing CO{sub 2

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration Results: Third Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Post, M.

2014-05-01

This report presents results of a demonstration of 12 fuel cell electric buses (FCEB) operating in Oakland, California. The 12 FCEBs operate as a part of the Zero Emission Bay Area (ZEBA) Demonstration, which also includes two new hydrogen fueling stations. This effort is the largest FCEB demonstration in the United States and involves five participating transit agencies. The ZEBA partners are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service. NREL has published two previous reports, in August 2011 and July 2012, describing operation of these buses. New results in this report provide an update covering eight months through October 2013.

Fuel consumption reduction in urban buses by using power split transmissions

International Nuclear Information System (INIS)

Macor, Alarico; Rossetti, Antonio

2013-01-01

Highlights: • Fuel consumption is highly influenced by transmission layout and control. • Continuous Variable Transmission allows control of the working point of the engine. • Hydromechanical CVT was numerically tested and compared with usual mechanical solutions. • CVT solution proved to reduce fuel consumption, improving the I.C.E. mean efficiency. • Results obtained from standard emission test cycles: New York and Manhattan Buses. - Abstract: The reduction of fuel consumption of urban vehicles is one of the challenges of the society today. Many promising technologies such as hybrid electric vehicles and fuel cells are the focus of a lot of research and investments, but high costs prevent their development on a large scale, especially in heavy duty vehicles. Simpler solutions, such as continuously variable transmissions, are then interesting alternatives: they preserve some of the advantages of hybrid solutions significantly reducing the overall cost of the system. Since these technologies allow the decoupling of the engine’s velocity from that of the wheels, optimised management of the engine becomes feasible, leading to lower fuel consumption than that of traditional solutions. This work compares the hydromechanical transmission with a traditional power shift in an application where efficiency and comfort are required: a city bus. The performance of a vehicle with a dual stage hydromechanical transmission has been investigated by means of a model implemented in the AMESim environment. A second model of a vehicle with a power shift transmission has been taken as reference solution. During the simulation of two standard test cycles, the first vehicle showed the lower fuel consumption, due to its better engine management, and to the operation of the torque converter during starts, which lowers the efficiency of the reference vehicle

Fuel Cell Electric Bus Evaluations | Hydrogen and Fuel Cells | NREL

Science.gov (United States)

Bus Evaluations Fuel Cell Electric Bus Evaluations NREL's technology validation team evaluates fuel cell electric buses (FCEBs) to provide comprehensive, unbiased evaluation results of fuel cell bus early transportation applications for fuel cell technology. Buses operate in congested areas where

Tracking costs of alternatively fueled buses in Florida.

Science.gov (United States)

2011-11-04

The goal of the current project is to establish a recording and reporting mechanism for collecting field data on the performance and costs of alternatively fueled public transit vehicles operating in Florida in order to assist policy makers with thei...

Ongoing evaluation of alternatively fueled buses : final report.

Science.gov (United States)

2016-05-01

The goal of this project is to continue collecting and reporting data on the performance and costs of alternatively fueled public transit vehicles in Florida in a consistent manner. Over the course of this project, researchers sent repeated data requ...

Tracking costs of alternatively fueled buses in Florida - phase II.

Science.gov (United States)

2013-04-01

The goal of this project is to continue collecting and reporting the data on the performance and costs of alternatively fueled public transit vehicles in the state in a consistent manner in order to keep the Bus Fuels Fleet Evaluation Tool (BuFFeT) c...

American Fuel Cell Bus Project Evaluation: Third Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jeffers, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-05-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB, which was developed as part of the Federal Transit Administration's (FTA) National Fuel Cell Bus Program, was delivered to SunLine in November 2011 and was put in revenue service in mid-December 2011. Two new AFCBs with an upgraded design were delivered in June/July of 2014 and a third new AFCB was delivered in February 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report covers the performance of the AFCBs from July 2015 through December 2016.

Hydrogen for buses in London: A scenario analysis of changes over time in refuelling infrastructure costs

International Nuclear Information System (INIS)

Shayegan, S.; Pearson, P.J.G.; Hart, D.

2009-01-01

The lack of a hydrogen refuelling infrastructure is one of the major obstacles to the introduction of the hydrogen vehicles to the road transport market. To help overcome this hurdle a likely transitional solution is to introduce hydrogen for niche applications such as buses or other types of fleet vehicles for which fuel demand is predictable and localised. This paper analyses the costs of different hydrogen production-delivery pathways, via a case study of buses in London. Scenario analysis over time (2007-2025) is used to investigate potential changes to the cost of hydrogen as a result of technology development, growing demand for hydrogen and changes in energy prices (gas and electricity). It is found that factors related to hydrogen demand have the greatest effect on the unit cost of hydrogen, while for the whole of the analysis period, on-site SMR (steam methane reforming) remains the least-cost production-delivery pathway. (author)

Checklist for transition to new highway fuel(s).

Energy Technology Data Exchange (ETDEWEB)

Risch, C.; Santini, D.J. (Energy Systems)

2011-12-15

Transportation is vital to the U.S. economy and society. As such, U.S. Presidents have repeatedly stated that the nation needs to reduce dependence on petroleum, especially for the highway transportation sector. Throughout history, highway transportation fuel transitions have been completed successfully both in United States and abroad. Other attempts have failed, as described in Appendix A: Historical Highway Fuel Transitions. Planning for a transition is critical because the changes can affect our nation's ability to compete in the world market. A transition will take many years to complete. While it is tempting to make quick decisions about the new fuel(s) of choice, it is preferable and necessary to analyze all the pertinent criteria to ensure that correct decisions are made. Doing so will reduce the number of changes in highway fuel(s). Obviously, changes may become necessary because of occurrences such as significant technology breakthroughs or major world events. With any and all of the possible transitions to new fuel(s), the total replacement of gasoline and diesel fuels is not expected. These conventional fuels are envisioned to coexist with the new fuel(s) for decades, while the revised fuel and vehicle infrastructures are implemented. The transition process must analyze the needs of the primary 'players,' which consist of the customers, the government, the fuel industry, and the automotive industry. To maximize the probability of future successes, the prime considerations of these groups must be addressed. Section 2 presents a succinct outline of the Checklist. Section 3 provides a brief discussion about the groupings on the Checklist.

Developing a Natural Gas-Powered Bus Rapid Transit Service: A Case Study

Energy Technology Data Exchange (ETDEWEB)

Mitchell, G.

2015-11-03

The Roaring Fork Transit Authority (RFTA) and its VelociRFTA Bus Rapid Transit (BRT) program are unique in many ways. For example, VelociRFTA was the first rural BRT system in the United States and the operational environment of the VelociRFTA BRT is one of the most severe in the country, with extreme winter temperatures and altitudes close to 8,000 feet. RFTA viewed high altitude operation as the most challenging characteristic when it began considering the use of natural gas. RFTA is the second-largest public transit system in Colorado behind Denver's Regional Transportation District (RTD), and it is one of the largest rural public transit systems in the country. In 2013, RFTA accepted delivery of 22 new compressed natural gas (CNG) buses that went into service after completion of maintenance and refueling facilities earlier that year. This paper examines the lessons learned from RFTA's experience of investigating--and ultimately choosing--CNG for their new BRT program and focuses on the unique environment of RFTA's BRT application; the decision process to include CNG fueling in the project; unforeseen difficulties encountered in the operation of CNG buses; public perception; cost comparison to competing fuels; and considerations for indoor fueling facilities and project funding.

Developing a Natural Gas-Powered Bus Rapid Transit Service. A Case Study

Energy Technology Data Exchange (ETDEWEB)

Mitchell, George [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2015-11-01

The Roaring Fork Transit Authority (RFTA) and its VelociRFTA Bus Rapid Transit (BRT) program are unique in many ways. For example, VelociRFTA was the first rural BRT system in the United States and the operational environment of the VelociRFTA BRT is one of the most severe in the country, with extreme winter temperatures and altitudes close to 8,000 feet. RFTA viewed high altitude operation as the most challenging characteristic when it began considering the use of natural gas. RFTA is the second-largest public transit system in Colorado behind Denver's Regional Transportation District (RTD), and it is one of the largest rural public transit systems in the country. In 2013, RFTA accepted delivery of 22 new compressed natural gas (CNG) buses that went into service after completion of maintenance and refueling facilities earlier that year. This paper examines the lessons learned from RFTA's experience of investigating--and ultimately choosing--CNG for their new BRT program and focuses on the unique environment of RFTA's BRT application; the decision process to include CNG fueling in the project; unforeseen difficulties encountered in the operation of CNG buses; public perception; cost comparison to competing fuels; and considerations for indoor fueling facilities and project funding.

Combustion Chemistry of Biodiesel for the Use in Urban Transport Buses: Experiment and Modeling

Science.gov (United States)

Omidvarborna, Hamid

Biofuels, such as biodiesel, offer benefits as a possible alternative to conventional fuels due to their fuel source sustainability and their reduced environmental impact. Before they can be used, it is essential to understand their combustion chemistry and emission characterizations due to a number of issues associated with them (e.g., high emission of nitrogen oxides (NOx), lower heating value than diesel, etc.). During this study, emission characterizations of different biodiesel blends (B0, B20, B50, and B100) were measured on three different feedstocks (soybean methyl ester (SME), tallow oil (TO), and waste cooking oil (WCO)) with various characteristics, while an ultra-low sulfur diesel (ULSD) was used as base fuel at low-temperature combustion (LTC). A laboratory combustion chamber was used to analyze soot formation, NOx emissions, while real engine emissions were measured for further investigation on PM and NOx emissions. For further study, carbon emissions (CO, CO 2, and CH4) were also measured to understand their relations with feedstocks' type. The emissions were correlated with fuel's characteristics, especially unsaturation degree (number of double bonds in methyl esters) and chain length (oxygen-to-carbon ratio). The experimental results obtained from laboratory experiments were confirmed by field experiments (real engines) collected from Toledo area regional transit authority (TARTA) buses. Combustion analysis results showed that the neat biodiesel fuels had longer ignition delays and lower ignition temperatures compared to ULSD at the tested condition. The results showed that biodiesel containing more unsaturated fatty acids emitted higher levels of NOx compared to biodiesel with more saturated fatty acids. A paired t-test on fuels showed that neat biodiesel fuels had significant reduction in the formation of NOx compared with ULSD. In another part of this study, biodiesel fuel with a high degree of unsaturation and high portion of long chains of

From prototype to product. The development of low emission natural gas- and biogas buses

Energy Technology Data Exchange (ETDEWEB)

Ekelund, M. [Strateco Development AB, Haninge (Sweden)

1998-01-01

The objective of this report is to show the development of natural gas and bio gas buses and trucks since the termination of the `Co-Nordic GasBus Project`, to which KFB was a major contributor and one of the initiators. Sweden have some 325 heavy duty methane vehicles of which almost 100 are bio gas operated. Scania and Volvo have produced, or have orders for, 500 gas buses to 6 different countries since 1990. The Project objectives were obtained and the significantly reduced emission levels aimed for, were shown. The international bus manufacturing industry followed, and have since shown the same low levels of emissions from gas bus engines. Sweden has taken the lead in the use of bio gas, by operating nearly 100 buses and trucks. Bio gas is still an underestimated fuel when it comes to supply, as it can provide fuel for 50% of the domestic use of diesel oil. Future development need to include control systems for more stable emissions, lower weight cylinders, less costly compressors, cleaning equipment and storage cylinders as well as more fuel efficient engines that can reduce mainly the discharge of CO2, NOx and CH4 further. Societal costs, regardless of who pays, for methane operated buses is still somewhat higher compared with best use of diesel + CRT technology. As commercialization develops, it is expected that the price of the vehicle will be reduced and emissions improved. It is therefore expected that the stake holders costs will be lower then that of diesel technology in the future

Alternative Fuels Data Center: Little Rock Gains Momentum with Natural Gas

Science.gov (United States)

Buses Little Rock Gains Momentum with Natural Gas Buses to someone by E-mail Share Alternative Fuels Data Center: Little Rock Gains Momentum with Natural Gas Buses on Facebook Tweet about Alternative Fuels Data Center: Little Rock Gains Momentum with Natural Gas Buses on Twitter Bookmark Alternative

Life Cycle Assessment of Diesel and Electric Public Transportation Buses

Science.gov (United States)

The Clean Air Act identifies diesel powered motor vehicles, including transit buses, as significant sources of several criteria pollutants which contribute to ground level ozone formation or smog. The effects of air pollution in urban areas are often more significant due to con...

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2008

Science.gov (United States)

2008-12-01

In September 2007, the U.S. Department of Energys (DOE) National Renewable Energy Laboratory (NREL) published a report that reviewed past and present fuel cell bus technology development and implementation in the United States. That report reviewe...

Zero Emission Bay Area (ZEBA) Fuel Cell Bus Demonstration: Second Results Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2012-07-01

This report presents results of a demonstration of 12 new fuel cell electric buses (FCEB) operating in Oakland, California. The 12 FCEBs operate as a part of the Zero Emission Bay Area (ZEBA) Demonstration, which also includes two new hydrogen fueling stations. This effort is the largest FCEB demonstration in the United States and involves five participating transit agencies. The ZEBA partners are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service. The first results report was published in August 2011, describing operation of these new FCEBs from September 2010 through May 2011. New results in this report provide an update through April 2012.

Optimization of transit bus fleet's life cycle assessment impacts with alternative fuel options

International Nuclear Information System (INIS)

Ercan, Tolga; Zhao, Yang; Tatari, Omer; Pazour, Jennifer A.

2015-01-01

Public transportation is one of the most promising transportation modes to reduce the environmental emissions of the transportation sector in the U.S. In order to mitigate the environmental impacts brought by the transit bus system, new energy buses are introduced into the vehicle market. The goal of this study is to find an optimal bus fleet combination for different driving conditions to minimize life cycle cost, greenhouse gas emissions, and conventional air pollutant emission impacts. For this purpose, a Multi-Objective Linear Programming approach is used to select the optimum bus fleet combinations. Given different weight scenarios, this method could effectively provide solutions for decision makers with various budget constraints or emission reduction requirements. The results indicate that in heavily congested driving cycles such as the Manhattan area, the battery electric bus is the dominant vehicle type, while the hybrid bus has more balanced performances in most scenarios because of its lower initial investment comparing to battery electric buses. Petroleum powered buses have seldom been selected by the model. The trade-off analysis shows that the overall greenhouse gas impact performance is sensitive to the life cycle cost after certain points, which could provide valuable information for the bus fleet combination planning. - Highlights: • Hybrid-Life Cycle Assessment analysis approach for transit bus operations. • Optimizing the economic and sustainability impacts of transit bus fleet operation. • CO 2 emissions and other air pollutants related health and environmental damage cost. • Trade-offs between CO 2 emissions and cost of transit bus fleet operation.

Hydrogen fuelled buses: Italian ENEA research program

International Nuclear Information System (INIS)

Ambrosini, G.; Ciancia, A.; Pede, G.

1993-01-01

Current hydrogen automotive fuels research studies being conducted by ENEA (Italian Agency for New Technology, Energy and the Environment) are being targeted towards the development of hydrogen fueled vans and buses for use in highly polluted urban environments where the innovative vehicles' air pollution abatement characteristics would justify their high operating costs as compared with those of conventional automotive alternatives. The demonstration vehicle being used in the experimental studies and performance tests is a two liter minibus with a spark ignition engine power rated at 55 kW with gasoline operation and 45 kW with hydrogen. Detailed design notes are given regarding the retrofitting of the minibus chassis to house the aluminium gas storage tanks and the adaptation of the engine to operate with compressed hydrogen. Attention is given to efforts being made to resolve combustion control and fueling problems. Focus is on the progress being made in the development of an efficient and safe electronically controlled fuel injection system

Alternative fuel news: Official publication of the clean cities network and the alternative fuels data center, Vol. 4, No. 1

Energy Technology Data Exchange (ETDEWEB)

NREL

2000-03-27

This issue of Alternative Fuel News contains information on the upcoming Clean Cities Conference to be held May 7--10, 2000 in San Diego, California. Highlighted in this issue is the success of the Clean Cities Program in creating clean corridors that permit fleets that serve multiple cities to purchase AFVs with confidence, knowing that fueling convenience and supply will not be a problem. Also look for articles on electric vehicles, transit buses; state and fuel provider enforcement; the Salt Lake and Greater Long Island Clean Cities coalitions, HEVs and fuel cells are a big hit at auto shows; DOE awards alternative fuel grants to 33 National Parks; and the Energy Policy Act (EPAct) Section 506 report.

Vehicle technologies, fuel-economy policies, and fuel-consumption rates of Chinese vehicles

International Nuclear Information System (INIS)

Huo Hong; He Kebin; Wang, Michael; Yao Zhiliang

2012-01-01

One of the principal ways to reduce transport-related energy use is to reduce fuel-consumption rates of motor vehicles (usually measured in liters of fuel per 100 km). Since 2004, China has implemented policies to improve vehicle technologies and lower the fuel-consumption rates of individual vehicles. Policy evaluation requires accurate and adequate information on vehicle fuel-consumption rates. However, such information, especially for Chinese vehicles under real-world operating conditions, is rarely available from official sources in China. For each vehicle type we first review the vehicle technologies and fuel-economy policies currently in place in China and their impacts. We then derive real-world (or on-road) fuel-consumption rates on the basis of information collected from various sources. We estimate that the real-world fuel-consumption rates of vehicles in China sold in 2009 are 9 L/100 km for light-duty passenger vehicles, 11.4 L/100 km for light-duty trucks, 22 L/100 km for inter-city transport buses, 40 L/100 km for urban transit buses, and 24.9 L/100 km for heavy-duty trucks. These results aid in understanding the levels of fuel consumption of existing Chinese vehicle fleets and the effectiveness of policies in reducing on-road fuel consumption, which can help in designing and evaluating future vehicle energy-efficiency policies. - Highlights: ► Vehicle fuel-consumption rate (VFCR) data are rarely available in China. ► We review the fuel-economy policies currently in place in China and their impacts. ► We derive real-world VFCRs on the basis of information collected from various sources. ► Results aid in understanding the fuel consumption levels of Chinese vehicle fleets. ► Results help in designing and evaluating future vehicle energy-efficiency policies.

Environmental impact assessment of bus rapid transit (BRT in the Metropolitan City of Tehran

Directory of Open Access Journals (Sweden)

F. Salehi

2016-01-01

Full Text Available Bus rapid transit is an innovative, high capacity, lower cost public transit solution in metropolitan cities. Idea is to dedicate lanes for quick and efficient transport of passengers to their destinations. In the present investigation the environmental impact assessment of bus rapid transit  in Tehran metropolitan city is brought out. For this purpose bus rapid transit Lane No. 10 is investigated. The bus rapid transit Lane No.10 is about 10 km in distance that moves up and down between Azadi and Simon Bolivar Squares. About 77500 passengers using 50 buses are transited per day in lane No. 10. These 50 buses cover a distance of 9600 km/day. The results of present study showed that about 6.5 million liters of fuel is saved annually. It should be pointed out that environmental costs are also reduced for about US$ 1.7 million/yr. The overall score of environmental impact assessment stands at +10 that is indicative of Lane No. 10 compatibility with the environmental considerations.

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Preliminary Evaluation Results

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2008-10-01

This report provides preliminary results from a National Renewable Energy Laboratory evaluation of a protoptye fuel cell transit bus operating at Connecticut Transit in Hartford. Included are descriptions of the planned fuel cell bus demonstration and equipment; early results and agency experience are also provided.

A cost-benefit analysis of alternatively fueled buses with special considerations for V2G technology

International Nuclear Information System (INIS)

Shirazi, Yosef; Carr, Edward; Knapp, Lauren

2015-01-01

Motivated by climate, health and economic considerations, alternatively-fueled bus fleets have emerged worldwide. Two popular alternatives are compressed natural gas (CNG) and electric vehicles. The latter provides the opportunity to generate revenue through vehicle-to-grid (V2G) services if properly equipped. This analysis conducts a robust accounting of the costs of diesel, CNG and battery-electric powertrains for school buses. Both marginal and fleet-wide scenarios are explored. Results indicate that the marginal addition of neither a small CNG nor a small V2G-enabled electric bus is cost effective at current prices. Contrary to previous findings, a small V2G-enabled electric bus increases net present costs by $7,200/seat relative to diesel for a Philadelphia, PA school district. A small CNG bus increases costs by $1,200/seat relative to diesel. This analysis is the first to quantify and include the economic implications of cold temperature extremes on electric vehicle battery operations, and the lower V2G revenues that result. Additional costs and limitations imposed by electric vehicles performing V2G are frequently overlooked in the literature and are explored here. If a variety of technical, legal, and economic challenges are overcome, a future eBus may be economical. - Highlights: • We present a robust cost-benefit analysis of various bus technologies. • Diesel is a low-cost technology at current prices. • CNG represents slightly higher costs on a marginal bus basis. • V2G-enabled electric buses are not cost-effective at current prices. • We identify frequently overlooked costs and challenges to V2G implementation.

Transition to a hydrogen fuel cell transit bus fleet for Canadian urban transit system

International Nuclear Information System (INIS)

Ducharme, P.

2004-01-01

'Full text:' The Canadian Transportation Fuel Cell Alliance (CTFCA), created by the Canadian Government as part of its 2000 Climate Change Action Plan, has commissioned MARCON-DDM's Hydrogen Intervention Team (HIT) to provide a roadmap for urban transit systems that wish to move to hydrogen fuel cell-powered bus fleets. HIT is currently in the process of gathering information from hydrogen technology providers, bus manufacturers, fuelling system providers and urban transit systems in Canada, the US and Europe. In September, HIT will be in a position to provide a preview of its report to the CTFCA, due for October 2004. The planned table of contents includes: TOMORROW'S FUEL CELL (FC) URBAN TRANSIT BUS - Powertrain, on-board fuel technologies - FC engine system manufacturers - Bus technical specifications, performances, operating characteristics - FC bus manufacturers TOMORROW'S FC TRANSIT PROPERTY - Added maintenance, facilities and fuelling infrastructure requirements - Supply chain implications - Environmental and safety issues - Alternative operational concepts PATHWAYS TO THE FUTURE - Choosing the future operational concept - 'Gap' assessment - how long from here to there? - Facilities and fleet adjustments, including fuelling infrastructure - Risk mitigation, code compliance measures TRANSITIONAL CONSIDERATIONS - Cost implications - Transition schedule (author)

NAA of an iridium tracer to determine soot exposure of students commuting on Baltimore`s buses

Energy Technology Data Exchange (ETDEWEB)

Ondov, J.M.; Wu, C.C.; Lin, Zhibo; Kidwell, C.B. [Univ. of Maryland, College Park, MD (United States)

1997-12-01

Epidemiologic studies suggest that short-term increases in indices of particulate air pollution are associated with increased mortality and morbidity from respiratory and cardiovascular diseases. An important component of urban aerosol, diesel soot, is a known respiratory irritant and contains mutagenic and carcinogenic organic compounds. In the United States, motor vehicles are thought to be the largest single source of atmospheric soot and account for {approximately}36% of the annual anthropogenic emission of toxic polynuclear aromatic hydrocarbons (PAH). Much of the motor-vehicle-derived PAH originates from diesel-powered vehicles because their PAH emissions are up to 50-fold greater than those from gasoline engines. In Baltimore, city high school students take public buses to school and, often, must stand at bus stops while many diesel buses pass or stop before their own buses arrive. To estimate student exposures to soot emitted from public diesel buses (MTA) during commutes to city high schools, the Baltimore municipal fuel supply was tagged with an iridium tracer, and exposure was monitored during commutes with personal aerosol monitors as a part of the Baltimore Environmental Justice Project.

Evaluating real-world CO2 and NOX emissions for public transit buses using a remote wireless on-board diagnostic (OBD) approach.

Science.gov (United States)

Yang, Liuhanzi; Zhang, Shaojun; Wu, Ye; Chen, Qizheng; Niu, Tianlin; Huang, Xu; Zhang, Shida; Zhang, Liangjun; Zhou, Yu; Hao, Jiming

2016-11-01

The challenge to mitigate real-world emissions from vehicles calls for powerful in-use compliance supervision. The remote on-board diagnostic (OBD) approach, with wireless data communications, is one of the promising next-generation monitoring methods. We collected second-by-second profiles of carbon dioxide (CO 2 ) and nitrogen oxides (NO X ) emissions, driving conditions and engine performance for three conventional diesel and three hybrid diesel buses participating in a remote OBD pilot program in Nanjing, China. Our results showed that the average CO 2 emissions for conventional diesel and hybrid diesel buses were 816 ± 83 g km -1 and 627 ± 54 g km -1 , respectively, under a typical driving pattern. An operating mode binning analysis indicated that CO 2 emissions reduction by series-parallel hybrid technology was largely because of the significant benefits of the technology under the modes of low speed and low power demand. However, significantly higher CO 2 emissions were observed for conventional diesel buses during rush hours, higher than 1200 g km -1 . The OBD data suggested no improvement in NO X emission reduction for hybrid buses compared with conventional buses; both were approximately 12 g km -1 because of poor performance of the selective catalyst reduction (SCR) systems in the real world. Speed-dependent functions for real-world CO 2 and NO X emissions were also constructed. The CO 2 emissions of hybrid buses were much less sensitive to the average speed than conventional buses. If the average speed decreased from 20 km h -1 to 10 km h -1 , the estimated CO 2 emission factor for conventional buses would be increased by 34%. Such a change in speed would increase NO X emissions for conventional and hybrid buses by 38% and 56%, respectively. This paper demonstrates the useful features of the remote OBD system and can inform policy makers how to take advantage of these features in monitoring in-use vehicles. Copyright © 2016 Elsevier

Fuel cells for vehicle applications in cars - bringing the future closer

Science.gov (United States)

Panik, Ferdinand

Among all alternative drive systems, the fuel cell electric propulsion system has the highest potential to compete with the internal combustion engine. For this reason, Daimler-Benz AG has entered into a co-operative alliance with Ballard Power Systems, with the objectives of bringing fuel cell vehicles to the market. Apart from the fuel cell itself, fuel cell vehicles require comprehensive system technology to provide fuel and air supply, cooling, energy management, electric and electronic functions. The system technology determines to a large extent the cost, weight, efficiency, performance and overall customer benefit of fuel cell vehicles. Hence, Daimler-Benz and Ballard are pooling their expertise in fuel cell system technology in a joint company, with the aim of bringing their fuel cell vehicular systems to the stage of maturity required for market entry as early as possible. Hydrogen-fuelled zero-emission fuel cell transit `buses' will be the first market segment addressed, with an emphasis on the North American and European markets. The first buses are already scheduled for delivery to customers in late 1997. Since a liquid fuel like methanol is easier to handle in passenger cars, fuel reforming technologies are developed and will shortly be demonstrated in a prototype, as well. The presentation will cover concepts of fuel cell vehicles with an emphasis on system technology, the related testing procedures and results as well as an outline of market entry strategies.

Alternative Fuels Data Center: Fleet Application for School Transportation

Science.gov (United States)

Propane Buses Jan. 26, 2016 Video thumbnail for Biodiesel Offers an Easy Alternative for Fleets Biodiesel thumbnail for Biodiesel Fuels Education in Alabama Biodiesel Fuels Education in Alabama May 1, 2012 Video School Transportation Videos on YouTube Video thumbnail for New Hampshire Cleans up with Biodiesel Buses

The effects of fuel characteristics and engine operating conditions on the elemental composition of emissions from heavy duty diesel buses

Energy Technology Data Exchange (ETDEWEB)

M.C.H. Lim; G.A. Ayoko; L. Morawska; Z.D. Ristovski; E.R. Jayaratne [Queensland University of Technology, Brisbane, Qld. (Australia). International Laboratory for Air Quality and Health, School of Physical and Chemical Sciences

2007-08-15

The effects of fuel characteristics and engine operating conditions on elemental composition of emissions from twelve heavy duty diesel buses have been investigated. Two types of diesel fuels - low sulfur diesel (LSD) and ultra low sulfur diesel (ULSD) fuels with 500 ppm and 50 ppm sulfur contents respectively and 3 driving modes corresponding to 25%, 50% and 100% power were used. Elements present in the tailpipe emissions were quantified by inductively coupled plasma mass spectrometry (ICPMS) and those found in measurable quantities included Mg, Ca, Cr, Fe, Cu, Zn, Ti, Ni, Pb, Be, P, Se, Ti and Ge. Multivariate analyses using multi-criteria decision making methods (MCDM), principal component analysis (PCA) and partial least squares (PLS) facilitated the extraction of information about the structure of the data. MCDM showed that the emissions of the elements were strongly influenced by the engine driving conditions while the PCA loadings plots showed that the emission factors of the elements were correlated with those of other pollutants such as particle number, total suspended particles, CO, CO{sub 2} and NOx. Partial least square analysis revealed that the emission factors of the elements were strongly dependent on the fuel parameters such as the fuel sulfur content, fuel density, distillation point and cetane index. Strong correlations were also observed between these pollutants and the engine power or exhaust temperature. The study provides insights into the possible role of fuel sulfur content in the emission of inorganic elements from heavy duty diesel vehicles. 39 refs., 1 fig., 4 tabs.

Thermodynamic analysis of the two-phase ejector air-conditioning system for buses

International Nuclear Information System (INIS)

Ünal, Şaban; Yilmaz, Tuncay

2015-01-01

Air-conditioning compressors of the buses are usually operated with the power taken from the engine of the buses. Therefore, an improvement in the air-conditioning system will reduce the fuel consumption of the buses. The improvement in the coefficient of performance (COP) of the air-conditioning system can be provided by using the two-phase ejector as an expansion valve in the air-conditioning system. In this study, the thermodynamic analysis of bus air-conditioning system enhanced with a two-phase ejector and two evaporators is performed. Thermodynamic analysis is made assuming that the mixing process in ejector occurs at constant cross-sectional area and constant pressure. The increase rate in the COP with respect to conventional system is analyzed in terms of the subcooling, condenser and evaporator temperatures. The analysis shows that COP improvement of the system by using the two phase ejector as an expansion device is 15% depending on design parameters of the existing bus air-conditioning system. - Highlights: • Thermodynamic analysis of the two-phase ejector refrigeration system. • Analysis of the COP increase rate of bus air-conditioning system. • Analysis of the entrainment ratio of the two-phase ejector refrigeration system

CNG/diesel buses for Texas school districts

International Nuclear Information System (INIS)

Armstrong, J.H.

1993-01-01

At the present time, the preponderance of trucks, buses and other heavy duty vehicles are powered by diesel engines. The reasons for the change from gasoline to diesel engines are all basically economic, due to the longer life and lower operating costs of diesel engines, as compared to gasoline engines. This provides a compelling reason to continue to use these engines, even if powered by fuel other than diesel. A major strategy within the industry has been the various attempts to adapt diesel engines to alternative fuels. These conversions have been largely to either methanol or natural gas, with propane joining the race just recently. This strategy takes advantage of the remaining life of existing vehicles by converting engines rather than purchasing a new engine (and/or vehicle) designed for and dedicated to an alternate fuel. Although diesel engines have been converted to run on natural gas, there are substantial challenges that must be met. The following describes some of the technical approaches being used for diesel engine conversions

Is the public willing to pay for hydrogen buses? A comparative study of preferences in four cities

International Nuclear Information System (INIS)

O'Garra, Tanya; Mourato, Susana; Garrity, Lisa; Schmidt, Patrick; Beerenwinkel, Anne; Altmann, Matthias; Hart, David; Graesel, Cornelia; Whitehouse, Simon

2007-01-01

This paper presents results from the international AcceptH2 study (http://www.accepth2.com) of acceptability and preferences for hydrogen fuel cell (FC) buses. Using the contingent valuation method, this paper compares public willingness to pay (WTP) for the air pollution reductions associated with a scenario of large-scale introduction of hydrogen (H 2 ) FC buses in four cities: Berlin, London, Luxembourg and Perth. Results indicate that bus users in all cities have a positive WTP for H 2 buses, and that values (adjusted to the cost of living in each city) are very similar across geographical locations (ranging from WTP an extra Euro 0.29 to Euro 0.35 per single bus fare). Non-bus users were also interviewed in London and Perth, in order to capture values for the whole populations in these cities. Combined results for bus users and non-bus users confirm that overall residents in these cities are willing to pay extra (in taxes) to support the large-scale introduction of H 2 -buses

Mitigation potential of greenhouse gas emission and implications on fuel consumption due to clean energy vehicles as public passenger transport in Kathmandu Valley of Nepal: A case study of trolley buses in Ring Road

International Nuclear Information System (INIS)

Pradhan, Shreekar; Ale, Bhakta Bahadur; Amatya, Vishwa Bhusan

2006-01-01

This paper estimates the consequences in fuel consumption and greenhouse gas emission due to the possible intervention of the electric run trolley buses in the existing public transport system in a particular road up to the year 2025 in Kathmandu Valley. It projects the scenarios on the basis that the passenger travel demand is the function of population and income. Basically, it uses the Long Range Energy Alternatives Planning System software to develop Business as Usual scenario and the five alternative scenarios. The alternative scenarios are 100% replacement of vehicles catering to mass-transit in the concerned routes, 50% replacement, 25% replacement, stopping future growth of other vehicles catering to mass-transit in the concerned routes and 25% replacement in the first year, and combination scenarios. The results estimate that the passenger travel demand will increase by three folds from the year 2003 to the year 2025. It projects the three-fold increase of the existing vehicle activity by the year 2025 in Business as Usual scenario. The fuel consumption will increase by 2.4 times compared to the year 2003. It estimates the total greenhouse gas (GHG) emission as 8.5 thousands tons in year 2003 which will increase by more than 3 times in year 2025. It estimates that 174.3 thousands t CO 2 e can be avoided in combination scenario. The paper concludes that the intervention of clean energy transport in the existing public transport can have a significant positive impact on the GHG emission and current fuel consumption

Hybrid Electric Transit Bus

Science.gov (United States)

Viterna, Larry A.

1997-01-01

A government, industry, and university cooperative is developing an advanced hybrid electric city transit bus. Goals of this effort include doubling the fuel economy compared to current buses and reducing emissions to one-tenth of current EPA standards. Unique aspects of the vehicle's power system include the use of ultra-capacitors as an energy storage system, and a planned natural gas fueled turbogenerator developed from a small jet engine. Power from both the generator and energy storage system is provided to a variable speed electric motor attached to the rear axle. At over 15000 kg gross weight, this is the largest vehicle of its kind ever built using ultra-capacitor energy storage. This paper describes the overall power system architecture, the evolution of the control strategy, and its performance over industry standard drive cycles.

Assessment of core characteristics during transition from 37-element fuel to CANFLEX-NU fuel in CANDU 6

International Nuclear Information System (INIS)

Jeong, Chang Joon; Suk, Ho Chun

2002-01-01

A transition from 37-element natural uranium fuel to CANFLEX-NU fuel has been modeled in a 1200-day time-dependent fuel management simulation for a CANDU 6 reactor. The simulation was divided into three parts. The pre-transition period extended from 0 to 300 FPD, in which the reactor was fuelled only with standard 37-element fuel bundles. In the transition period, refueling took place only with the CANFLEX-NU fuel bundle. The transition stage lasted from 300 to 920 FPD, at which point all of the 37-element fuel in the core had been replaced by CANFLEX-NU fuel bundle. In the post-transition phase, refueling continued with CANFLEX-NU fuel until 1200 FPD, to arrive at estimate of the equilibrium core characteristics with CANFLEX-NU fuel. Simulation results show that the CANFLEX-NU fuel bundle has a operational compatibility with the CANDU 6 reactor during the transition core, and also show that the transition core from 37-element natural uranium fuel to CANFLEX-NU can be operated without violating any license limit of the CANDU 6 reactor

Cost Effectiveness Analysis of Quasi-In-Motion Wireless Power Transfer for Plug-In Hybrid Electric Transit Buses from Fleet Perspective

Energy Technology Data Exchange (ETDEWEB)

Wang, Lijuan; Gonder, Jeff; Brooker, Aaron; Meintz, Andrew; Konan, Arnaud; Markel, Tony

2016-05-16

This study evaluated the costs and benefits associated with the use of stationary-wireless-power-transfer-enabled plug-in hybrid electric buses and determined the cost effectiveness relative to conventional buses and hybrid electric buses. A factorial design was performed over a number of different battery sizes, charging power levels, and f bus stop charging stations. The net present costs were calculated for each vehicle design and provided the basis for design evaluation. In all cases, given the assumed economic conditions, the conventional bus achieved the lowest net present cost while the optimal plug-in hybrid electric bus scenario beat out the hybrid electric comparison scenario. The parameter sensitivity was also investigated under favorable and unfavorable market penetration assumptions.

Buses involved in fatal accidents factbook 2007

Science.gov (United States)

2010-03-01

This document presents aggregate statistics on buses involved in traffic accidents in 2007. The : statistics are derived from the Buses Involved in Fatal Accidents (BIFA) file, compiled by the : University of Michigan Transportation Research Institut...

Evaluation of retrofit crankcase ventilation controls and diesel oxidation catalysts for reducing air pollution in school buses

Science.gov (United States)

Trenbath, Kim; Hannigan, Michael P.; Milford, Jana B.

2009-12-01

This study evaluates the effect of retrofit closed crankcase ventilation filters (CCFs) and diesel oxidation catalysts (DOCs) on the in-cabin air quality in transit-style diesel school buses. In-cabin pollution levels were measured on three buses from the Pueblo, CO District 70 fleet. Monitoring was conducted while buses were driven along their regular routes, with each bus tested three times before and three times after installation of control devices. Ultrafine number concentrations in the school bus cabins were 33-41% lower, on average, after the control devices were installed. Mean mass concentrations of particulate matter less than 2.5 μm in diameter (PM2.5) were 56% lower, organic carbon (OC) 41% lower, elemental carbon (EC) 85% lower, and formaldehyde 32% lower after control devices were installed. While carbon monoxide concentrations were low in all tests, mean concentrations were higher after control devices were installed than in pre-retrofit tests. Reductions in number, OC, and formaldehyde concentrations were statistically significant, but reductions in PM2.5 mass were not. Even with control devices installed, during some runs PM2.5 and OC concentrations in the bus cabins were elevated compared to ambient concentrations observed in the area. OC concentrations inside the bus cabins ranged from 22 to 58 μg m -3 before and 13 to 33 μg m -3 after control devices were installed. OC concentrations were correlated with particle-bound organic tracers for lubricating oil emissions (hopanes) and diesel fuel and tailpipe emissions (polycyclic aromatic hydrocarbons (PAH) and aliphatic hydrocarbons). Mean concentrations of hopanes, PAH, and aliphatic hydrocarbons were lower by 37, 50, and 43%, respectively, after the control devices were installed, suggesting that both CCFs and DOCs were effective at reducing in-cabin OC concentrations.

Location Planning for Dynamic Wireless Charging Systems for Electric Airport Passenger Buses

Directory of Open Access Journals (Sweden)

Stefan Helber

2018-01-01

Full Text Available The majority of the ground vehicles operating on the airside parts of commercial airports are currently powered by diesel engines. These include vehicles such as apron buses, fuel trucks, and aircraft tractors. Hence, these vehicles contribute to the overall CO 2 emissions of the aviation transport system and thus negatively influence its environmental footprint. To reduce this damaging environmental impact, these vehicles could potentially be electrified with on-board batteries as their energy sources. However, the conductive charging of such vehicles via stationary cable connections is rather time-consuming. A dynamic wireless charging system to supply public transportation passenger buses with electric energy while in motion has recently been installed on the Korea Advanced Institute of Science and Technology (KAIST campus and in the Korean city of Gumi. In this paper, we study configuration problems related to the use of this technology to make airport operations more environmentally sustainable. We concentrate on the power supply for apron buses and analyze the location planning problems related to the distribution of the required power supply and the wireless charging units in the apron road system. To this end, we develop a formal optimization model and discuss the first numerical results.

Final Report: Mass Production Cost Estimation of Direct H2 PEM Fuel Cell Systems for Transportation Applications (2012-2016)

Energy Technology Data Exchange (ETDEWEB)

James, Brian David [Strategic Analysis Inc., Arlington, VA (United States); Huya-Kouadio, Jennie Moton [Strategic Analysis Inc., Arlington, VA (United States); Houchins, Cassidy [Strategic Analysis Inc., Arlington, VA (United States); DeSantis, Daniel Allen [Strategic Analysis Inc., Arlington, VA (United States)

2016-09-01

This report summarizes project activities for Strategic Analysis, Inc. (SA) Contract Number DE-EE0005236 to the U.S. Department of Energy titled “Transportation Fuel Cell System Cost Assessment”. The project defined and projected the mass production costs of direct hydrogen Proton Exchange Membrane fuel cell power systems for light-duty vehicles (automobiles) and 40-foot transit buses. In each year of the five-year contract, the fuel cell power system designs and cost projections were updated to reflect technology advances. System schematics, design assumptions, manufacturing assumptions, and cost results are presented.

Buse_Francisella Medium

Data.gov (United States)

U.S. Environmental Protection Agency — This dataset contains colony forming unit and qPCR data. This dataset is associated with the following publication: Morris, B., H. Buse, N. Adcock, and E. Rice. A...

Buses involved in fatal accidents codebook 2008.

Science.gov (United States)

2011-03-01

This report provides documentation for UMTRIs file of Buses Involved in Fatal Accidents (BIFA), 2008, : including distributions of the code values for each variable in the file. The 2008 BIFA file is a census of all : buses involved in a fatal acc...

Buses involved in fatal accidents codebook 2007.

Science.gov (United States)

2009-12-01

This report provides documentation for UMTRIs file of Buses Involved in Fatal Accidents (BIFA), 2007, : including distributions of the code values for each variable in the file. The 2007 BIFA file is a census of all : buses involved in a fatal acc...

Hydrogen fuel cells for cars and buses

NARCIS (Netherlands)

Janssen, L.J.J.

2007-01-01

The use of hydrogen fuel cells for cars is strongly promoted by the governments of many countries and by international organizations like the European Community. The electrochem. behavior of the most promising fuel cell (polymer electrolyte membrane fuel cell, PEMFC) is critically discussed, based

49 CFR 393.89 - Buses, driveshaft protection.

Science.gov (United States)

2010-10-01

... ACCESSORIES NECESSARY FOR SAFE OPERATION Miscellaneous Parts and Accessories § 393.89 Buses, driveshaft protection. Any driveshaft extending lengthways under the floor of the passenger compartment of a bus shall... 49 Transportation 5 2010-10-01 2010-10-01 false Buses, driveshaft protection. 393.89 Section 393...

Transition Analysis of Promising U.S. Future Fuel Cycles Using ORION

International Nuclear Information System (INIS)

Sunny, Eva E.; Worrall, Andrew; Peterson, Joshua L.; Powers, Jeffrey J.; Gehin, Jess C.; Gregg, Robert

2015-01-01

The US Department of Energy Office of Fuel Cycle Technologies performed an evaluation and screening (E&S) study of nuclear fuel cycle options to help prioritize future research and development decisions. Previous work for this E&S study focused on establishing equilibrium conditions for analysis examples of 40 nuclear fuel cycle evaluation groups (EGs) and evaluating their performance according to a set of 22 standardized metrics. Following the E&S study, additional studies are being conducted to assess transitioning from the current US fuel cycle to future fuel cycle options identified by the E&S study as being most promising. These studies help inform decisions on how to effectively achieve full transition, estimate the length of time needed to undergo transition from the current fuel cycle, and evaluate performance of nuclear systems and facilities in place during the transition. These studies also help identify any barriers to achieve transition. Oak Ridge National Laboratory (ORNL) Fuel Cycle Options Campaign team used ORION to analyze the transition pathway from the existing US nuclear fuel cycle—the once-through use of low-enriched-uranium (LEU) fuel in thermal-spectrum light water reactors (LWRs)—to a new fuel cycle with continuous recycling of plutonium and uranium in sodium fast reactors (SFRs). This paper discusses the analysis of the transition from an LWR to an SFR fleet using ORION, highlights the role of lifetime extensions of existing LWRs to aid transition, and discusses how a slight delay in SFR deployment can actually reduce the time to achieve an equilibrium fuel cycle.

US activities on fuel cycle transition scenarios

International Nuclear Information System (INIS)

McCarthy, Kathryn A.

2010-01-01

Countries with active nuclear programmes typically have as a goal transition to a closed fuel cycle. A closed fuel cycle enables long-term sustainability, provides waste management benefits, and as a system, can reduce overall proliferation risk. This transition will take many decades, thus the study of the actual transition is an important topic. The United States systems analysis activities as part of the Advanced Fuel Cycle Initiative (AFCI) provide the integrating analyses for the fuel cycle programme, and recent activities are focusing on transition options, and specifically, the dynamics of the transition. The United States is still studying both one-tier (recycling in fast reactors only) and two-tier (recycling in both thermal and fast reactors) systems, and the systems analysis activities provide insight into the trade-offs associated with the systems, and variations of each. Most recently, a series of sensitivity studies have been completed which provide insight into the behaviour of a transition system. These studies evaluate the impact of changing various parameters in the fuel cycle system, and provide insight into how the system will change as parameters change. Because these deployment analyses look at the development of nuclear energy systems over a long period of time, it is very unlikely that we will accurately predict the system's characteristics over time (for example, growth in electricity demand, how quickly nuclear reactors will be deployed, how many fast rectors versus thermal reactors, the conversion ratio of the fast reactors, etc.). How the system will develop will depend on a variety of factors, ranging from political to technical, rational to irrational. Because we cannot accurately predict the future, we need to understand how things could change, and what impact those changes have. Analyses of future fuel cycle systems require a number of assumptions. These include growth rates for nuclear energy, general architecture of fuel cycle

Thermal Safety of the Current Buses in the Chimney of the D0 Solenoid

International Nuclear Information System (INIS)

Smith, R.P.

1998-01-01

The thermal and electrical behaviour of the current buses in the chimney of the D0 solenoid during upset conditions is modeled to guide the selection of trip levels for magnet protection circuits which discharge the magnet if abnormal conditions are detected. The current buses in the chimney are designed to operate safely without likelihood of loss of superconductivity as long as normal cooling conditions are maintained. Helium liquid level probes, helium flow instrumentation, and thermometry all are provided to certify that proper cooling conditions exist in the subcooler and chimney at all times. Rising temperatures in any portion of the system, excessive voltage drops on the vapor cooled leads, or decreasing liquid level in the subcooler or flow rate in the system, will each cause the fast discharge system to be triggered. Postulated failures of the helium flow system, somehow undetected by any and all of the aforementioned instrumentation, can in principal eventually lead to loss of superconductivity in the buses. Quenching in one bus will rapidly lead to quenching in the other. Potential taps on the buses and magnet coil halves connected to voltage-detection bridges external to the system provide at least dually redundant signals which will unambiguously trigger the magnet rapid discharge system. The conservative design of the bus system ensures that it will not be damaged during such incidents, however improbable they may be. The transition leads in the subcooler are equally conservatively designed, and would not be damaged if they were operated in a fully non-superconducting state for several minutes. The loss of liquid helium in the sub cooler required to cause this condition would imply that helium flow from the magnet had stopped, which in turn would imply that flow to the magnet had also stopped. The lack of flow into the sub cooler would result in insufficient flow to the vapor cooled leads. Any or all of these conditions would be detected, as would

75 FR 62695 - Physical Protection of Irradiated Reactor Fuel in Transit

Science.gov (United States)

2010-10-13

... Irradiated Reactor Fuel in Transit AGENCY: Nuclear Regulatory Commission. ACTION: Proposed rule. SUMMARY: The... nuclear fuel in transit? H. Why require a telemetric position monitoring system or an alternative tracking... nuclear fuel in transit. The interim final rule added 10 CFR 73.37, ``Requirements for Physical Protection...

78 FR 50313 - Physical Protection of Irradiated Reactor Fuel in Transit

Science.gov (United States)

2013-08-19

... Irradiated Reactor Fuel in Transit AGENCY: Nuclear Regulatory Commission. ACTION: Orders; rescission. SUMMARY... the NRC published a final rule, ``Physical Protection of Irradiated Fuel in Transit,'' on May 20, 2013... of Irradiated Reactor Fuel in Transit'' (RIN 3150-AI64; NRC-2009-0163). The final rule incorporates...

COMPARISON OF PARALLEL AND SERIES HYBRID POWERTRAINS FOR TRANSIT BUS APPLICATION

Energy Technology Data Exchange (ETDEWEB)

Gao, Zhiming [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL; Jones, Perry T [ORNL; LaClair, Tim J [ORNL; Parks, II, James E [ORNL

2016-01-01

The fuel economy and emissions of both conventional and hybrid buses equipped with emissions aftertreatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicate that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar CO and HC tailpipe emissions but were also predicted to have reduced NOx tailpipe emissions compared to the conventional bus in higher speed cycles. For the New York bus cycle (NYBC), which has the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus, while the parallel hybrid bus had significantly lower tailpipe emissions. All three bus powertrains were found to require periodic active DPF regeneration to maintain PM control. Plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed due to the relatively large battery capacity that is typical of the series hybrid configuration.

Alternative Fuels Data Center: Mesa Unified School District Reaps Economic

Science.gov (United States)

and Environmental Benefits with Propane Buses Mesa Unified School District Reaps Economic and School District Reaps Economic and Environmental Benefits with Propane Buses on Facebook Tweet about Alternative Fuels Data Center: Mesa Unified School District Reaps Economic and Environmental Benefits with

Hydrogen fueling stations in Japan hydrogen and fuel cell demonstration project

International Nuclear Information System (INIS)

Koseki, K.; Tomuro, J.; Sato, H.; Maruyama, S.

2004-01-01

A new national demonstration project of fuel cell vehicles, which is called Japan Hydrogen and Fuel Cell Demonstration Project (JHFC Project), has started in FY2002 on a four-year plan. In this new project, ten hydrogen fueling stations have been constructed in Tokyo and Kanagawa area in FY2002-2003. The ten stations adopt the following different types of fuel and fueling methods: LPG reforming, methanol reforming, naphtha reforming, desulfurized-gasoline reforming, kerosene reforming, natural gas reforming, water electrolysis, liquid hydrogen, by-product hydrogen, and commercially available cylinder hydrogen. Approximately fifty fuel cell passenger cars and a fuel cell bus are running on public roads using these stations. In addition, two hydrogen stations will be constructed in FY2004 in Aichi prefecture where The 2005 World Exposition (EXPO 2005) will be held. The stations will service eight fuel cell buses used as pick-up buses for visitors. We, Engineering Advancement Association of Japan (ENAA), are commissioned to construct and operate a total of twelve stations by Ministry of Economy Trade and Industry (METI). We are executing to demonstrate or identify the energy-saving effect, reduction of the environmental footprint, and issues for facilitating the acceptance of hydrogen stations on the basis of the data obtained from the operation of the stations. (author)

Transition analysis of promising U.S. future fuel cycles using ORION - 5114

International Nuclear Information System (INIS)

Sunny, E.; Worrall, A.; Peterson, J.; Powers, J.; Gehin, J.

2015-01-01

The US Department of Energy Office of Fuel Cycle Technologies performed an evaluation and screening (E/S) study of nuclear fuel cycle options to help prioritize future research and development decisions. Previous work for this E/S study focused on establishing equilibrium conditions for analysis examples of 40 nuclear fuel cycle evaluation groups and evaluating their performance according to a set of 22 standardized metrics. Following the E/S study, additional studies are being conducted to assess transition period from the current US fuel cycle to future fuel cycle options identified by the E/S study as being most promising. These studies help inform decisions on how to effectively achieve full transition, estimate the length of time needed to undergo transition from the current fuel cycle, and evaluate performance of nuclear systems and facilities in place during the transition. These studies also help identify any barriers to achieve transition. Oak Ridge National Laboratory (ORNL) Fuel Cycle Options Campaign team used ORION to analyze the transition pathway from the existing US nuclear fuel cycle - the once-through use of low-enriched-uranium (LEU) fuel in thermal-spectrum light water reactors (LWRs) - to a new fuel cycle with continuous recycling of plutonium and uranium in sodium fast reactors (SFRs). This paper discusses the analysis of the transition from an LWR to an SFR fleet using ORION, highlights the role of lifetime extensions of existing LWRs to aid transition, and discusses how a slight delay in SFR deployment can actually reduce the time to achieve an equilibrium fuel cycle. (authors)

Air quality in inter-city buses : final report

International Nuclear Information System (INIS)

2005-01-01

Various studies have suggested that air quality inside automobiles and school buses may be poorer than ambient or nearby air quality, and that concentrations of vehicle-related pollutants in city buses may be sufficiently elevated to pose concerns for vehicle occupants and operators. This paper presented the results of preliminary investigation of levels of some pollutants in inter-city buses to determine whether a fuller investigation is warranted. Another objective of the investigation was to develop methods for assessing air quality within road vehicles. Students carried monitoring equipment on 28 inter-city trips made by Greyhound Canada buses during July and August 2004. The equipment recorded average levels of carbon monoxide (CO) and nitrogen dioxide (NO 2 ), as well as concentrations of particulate matter. Bus routes were selected that allowed for an average of 10 hours of total sampling time in a day. Data was recorded on pumps, run times and routes taken. Results indicated that levels of CO in the buses were much lower than the national standard of acceptable levels for CO. Levels of NO 2 were on average lower, but 5 of the 19 recorded values exceeded acceptable levels. Average particulate levels recorded in the buses were considered acceptable, although some of the recorded levels were higher than desirable. It was concluded that further work on in-vehicle levels of NO 2 and particulate matter could be warranted. Although several procedural and equipment problems were encountered, the methods used in the investigation appeared to be valid, and were thought to be suitable for further work on in-vehicle concentrations of pollutants. 21 refs

CIEMAT analyses of transition fuel cycle scenarios

International Nuclear Information System (INIS)

Alvarez-Velarde, F.; Gonzalez-Romero, E.M.

2010-01-01

The efficient design of strategies for the long-term sustainability of nuclear energy or the phase-out of this technology is possible after the study of transition scenarios from the current fuel cycle to a future one with advanced technologies and concepts. CIEMAT has participated in numerous fuel cycle scenarios studies for more than a decade and, from some years ago, special attention has been put in the study of transition scenarios. In this paper, the main characteristics of each studied transition scenario are described. The main results and partial conclusions of each scenario are also analyzed. As general conclusions of transition studies, we highlight that the advantages of advanced technologies in transition scenarios can be obtained by countries or regions with sufficiently large nuclear parks, with a long-term implementation of the strategy. For small countries, these advantages are also accessible with an affordable cost, by means of the regional collaboration during several decades. (authors)

Core analysis during transition from 37-element fuel to CANFLEX-NU fuel in CANDU 6

Energy Technology Data Exchange (ETDEWEB)

Jeong, Chang Joon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1999-12-31

An 1200-day time-dependent fuel-management for the transition from 37-element fuel to CANFLEX-NU fuel in a CANDU 6 reactor has been simulated to show the compatibility of the CANFLEX-NU fuel with the reactor operation. The simulation calculations were carried out with the RFSP code, provided by cell averaged fuel properties obtained from the POWDERPUFS-V code. The refueling scheme for both fuels was an eight bundle shift at a time. The simulation results show that the maximum channel and bundle powers were maintained below the license limit of the CANDU 6. This indicates that the CANFLEX-NU fuel bundle is compatible with the CANDU 6 reactor operation during the transition period. 3 refs., 2 figs., 1 tab. (Author)

Core analysis during transition from 37-element fuel to CANFLEX-NU fuel in CANDU 6

Energy Technology Data Exchange (ETDEWEB)

Jeong, Chang Joon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

An 1200-day time-dependent fuel-management for the transition from 37-element fuel to CANFLEX-NU fuel in a CANDU 6 reactor has been simulated to show the compatibility of the CANFLEX-NU fuel with the reactor operation. The simulation calculations were carried out with the RFSP code, provided by cell averaged fuel properties obtained from the POWDERPUFS-V code. The refueling scheme for both fuels was an eight bundle shift at a time. The simulation results show that the maximum channel and bundle powers were maintained below the license limit of the CANDU 6. This indicates that the CANFLEX-NU fuel bundle is compatible with the CANDU 6 reactor operation during the transition period. 3 refs., 2 figs., 1 tab. (Author)

46 CFR 111.30-19 - Buses and wiring.

Science.gov (United States)

2010-10-01

... control wiring must be— (1) Suitable for installation within in a switchboard enclosure and be rated at 90... 46 Shipping 4 2010-10-01 2010-10-01 false Buses and wiring. 111.30-19 Section 111.30-19 Shipping... REQUIREMENTS Switchboards § 111.30-19 Buses and wiring. (a) General. Each bus must meet the requirements of...

Big Brother Is Watching: Video Surveillance on Buses

Science.gov (United States)

Sloggett, Joel

2009-01-01

Many school districts in North America have adopted policies to permit cameras on their properties and, when needed, on buses used to transport students. With regard to school buses, the camera is typically a tool for gathering information to monitor behavior or to help investigate a complaint about behavior. If a picture is worth a thousand…

CNG: a potential transport fuel

International Nuclear Information System (INIS)

Anon.

1992-01-01

Compressed Natural Gas (CNG) is an alternative transport fuel. Advantages of its use are briefly described. Infra structural requirements, if it is to be used in India are outlined. Applications of CNG as transport fuel for buses and trucks in India are discussed. (P.R.K.). 5 refs

49 CFR 393.90 - Buses, standee line or bar.

Science.gov (United States)

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Buses, standee line or bar. 393.90 Section 393.90 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY... NECESSARY FOR SAFE OPERATION Miscellaneous Parts and Accessories § 393.90 Buses, standee line or bar. Except...

Particle and gaseous emissions from individual diesel and CNG buses

Directory of Open Access Journals (Sweden)

Å. M. Hallquist

2013-05-01

Full Text Available In this study size-resolved particle and gaseous emissions from 28 individual diesel-fuelled and 7 compressed natural gas (CNG-fuelled buses, selected from an in-use bus fleet, were characterised for real-world dilution scenarios. The method used was based on using CO2 as a tracer of exhaust gas dilution. The particles were sampled by using an extractive sampling method and analysed with high time resolution instrumentation EEPS (10 Hz and CO2 with a non-dispersive infrared gas analyser (LI-840, LI-COR Inc. 1 Hz. The gaseous constituents (CO, HC and NO were measured by using a remote sensing device (AccuScan RSD 3000, Environmental System Products Inc.. Nitrogen oxides, NOx, were estimated from NO by using default NO2/NOx ratios from the road vehicle emission model HBEFA3.1. The buses studied were diesel-fuelled Euro III–V and CNG-fuelled Enhanced Environmentally Friendly Vehicles (EEVs with different after-treatment, including selective catalytic reduction (SCR, exhaust gas recirculation (EGR and with and without diesel particulate filter (DPF. The primary driving mode applied in this study was accelerating mode. However, regarding the particle emissions also a constant speed mode was analysed. The investigated CNG buses emitted on average a higher number of particles but less mass compared to the diesel-fuelled buses. Emission factors for number of particles (EFPN were EFPN, DPF = 4.4 ± 3.5 × 1014, EFPN, no DPF = 2.1 ± 1.0 × 1015 and EFPN, CNG = 7.8 ± 5.7 ×1015 kg fuel−1. In the accelerating mode, size-resolved emission factors (EFs showed unimodal number size distributions with peak diameters of 70–90 nm and 10 nm for diesel and CNG buses, respectively. For the constant speed mode, bimodal average number size distributions were obtained for the diesel buses with peak modes of ~10 nm and ~60 nm. Emission factors for NOx expressed as NO2 equivalents for the diesel buses were on average 27 ± 7 g (kg fuel−1 and for the CNG buses 41

Comparison of Life Cycle energy consumption and GHG emissions of natural gas, biodiesel and diesel buses of the Madrid transportation system

International Nuclear Information System (INIS)

García Sánchez, Juan Antonio; López Martínez, José María; Lumbreras Martín, Julio; Flores Holgado, Maria Nuria

2012-01-01

This paper presents a comparative study on the use of three after-treatment technologies: i) EGR + DPF, ii) SCR + Urea and iii) 3-way catalyst when implemented in urban buses, to determinate the energy requirements, greenhouse gas emissions (GHG), direct Land Use Change (dLUC), abiotic depletion of fossil energy by means of a Life Cycle Assessment (LCA). The process of production, conditioning and transporting of the fuels used by the buses (diesel, biodiesel (B100), a blended biodiesel at 20% (B20) and natural gas) were also analyzed (Well-to-Tank analysis) along with the environmental impact due to its combustion in the bus (Tank-to-Wheel analysis). The environmental impact of the manufacturing, maintenance and recycling process of the urban buses and exhaust after-treatment systems has also been evaluated. Main results shows that Life Cycle of SCR + Urea technology reduces environmental impact to a greater extent than its global Life Cycle increases it when gasoil is used resulting in a final balance more efficient than the other options, the same behavior is observed with the use of B20 and B100 but only when 0%dLUC is assumed since if the percentage of dLUC increases the effectiveness of the SCR + Urea technology in the reduction of environmental impact tend to decrease. -- Highlights: ► We examine the environmental impact caused by the Life Cycle of each technology, fossil fuel, biofuel and vehicle. ► Biodiesel environmental impact depends largely on land transformed for grow crops. ► Using SCR + Urea technology and gasoil as a fuel in the bus further reduces the environmental impact.

49 CFR 392.63 - Towing or pushing loaded buses.

Science.gov (United States)

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Towing or pushing loaded buses. 392.63 Section 392... COMMERCIAL MOTOR VEHICLES Prohibited Practices § 392.63 Towing or pushing loaded buses. No disabled bus with... passengers aboard for the purpose of towing or pushing any disabled motor vehicle, except in such...

School buses, air pollution and children's health : improving children's health and local air quality by reducing school bus emissions

Energy Technology Data Exchange (ETDEWEB)

Perrotta, K. [Ontario Public Health Association, Toronto, ON (Canada)

2005-11-01

The exhaust gases from school buses was examined and recommendations were presented for the establishment of a healthy school bus program in Ontario that is directed at improving children's health and local air quality. The Ontario Public Health Association is concerned with school bus emissions because they are heavy-duty vehicles that emit large quantities of diesel-related air pollutants such as fine particulate matter, nitrogen oxides and diesel particulates. In addition, school buses can be self-polluting vehicles that expose children on-board to high levels of fine particulates and diesel particulate matter. Both these pollutants have been associated with a range of acute and chronic health problems such as asthma, respiratory infections, allergies, and school absences. With nearly 800,000 Ontario children being transported on school buses annually, these exposures can represent a serious public health concern, as childhood exposures can also influence the health of exposed individuals later in life. Exposure studies have found that tailpipe and engine emissions contribute greatly to concentrations of air pollutants on-board school buses. The studies also showed that on-board concentrations were also influenced by local air quality in the communities studied, traffic density, wind direction, the configuration of windows, idling and queuing patterns. It was recommended that the use of ultra-low sulphur diesel fuel along with the installation of diesel particulate filters and closed crankcase filters can reduce the concentrations of air pollutants on-board school buses to almost ambient air levels, even under idling conditions. This report recommended the replacement of pre-1994 school buses, the retrofitting of 1994-2003 school buses with filters, and maintaining proper maintenance, idling and vehicle operation practices. refs., tabs., figs.

Crashworthiness evaluation of mass transit buses.

Science.gov (United States)

2008-11-01

Mass transit bus systems are an integral part of the national transportation network, serving more than 20.6 billion passenger-miles per year with a relatively low fatality rate. Bus occupant injuries are evenly distributed among crashes on all sides...

76 FR 53102 - Federal Motor Vehicle Safety Standards; Denial of Petition for Rulemaking; School Buses

Science.gov (United States)

2011-08-25

... small school buses to provide adequate crash protection for the occupants. For large school buses, FMVSS... and crash protection,'' requires lap/shoulder belts for all seating positions on small school buses... for adequate occupant crash protection. For large school buses, we have determined there is not a...

Bluetooth wireless monitoring, diagnosis and calibration interface for control system of fuel cell bus in Olympic demonstration

Energy Technology Data Exchange (ETDEWEB)

Hua, Jianfeng; Lin, Xinfan; Xu, Liangfei; Li, Jianqiu; Ouyang, Minggao [Tsinghua University, State Key Laboratory of Automotive Safety and Energy, Beijing100084 (China)

2009-01-15

With the worldwide deterioration of the natural environment and the fossil fuel crisis, the possible commercialization of fuel cell vehicles has become a hot topic. In July 2008, Beijing started a clean public transportation plan for the 29th Olympic games. Three fuel cell city buses and 497 other low-emission vehicles are now serving the Olympic core area and Beijing urban areas. The fuel cell buses will operate along a fixed bus line for 1 year as a public demonstration of green energy vehicles. Due to the specialized nature of fuel cell engines and electrified power-train systems, measurement, monitoring and calibration devices are indispensable. Based on the latest Bluetooth wireless technology, a novel Bluetooth universal data interface was developed for the control system of the fuel cell city bus. On this platform, a series of wireless portable control auxiliary systems have been implemented, including wireless calibration, a monitoring system and an in-system programming platform, all of which are ensuring normal operation of the fuel cell buses used in the demonstration. (author)

Empirical membrane lifetime model for heavy duty fuel cell systems

Science.gov (United States)

Macauley, Natalia; Watson, Mark; Lauritzen, Michael; Knights, Shanna; Wang, G. Gary; Kjeang, Erik

2016-12-01

Heavy duty fuel cells used in transportation system applications such as transit buses expose the fuel cell membranes to conditions that can lead to lifetime-limiting membrane failure via combined chemical and mechanical degradation. Highly durable membranes and reliable predictive models are therefore needed in order to achieve the ultimate heavy duty fuel cell lifetime target of 25,000 h. In the present work, an empirical membrane lifetime model was developed based on laboratory data from a suite of accelerated membrane durability tests. The model considers the effects of cell voltage, temperature, oxygen concentration, humidity cycling, humidity level, and platinum in the membrane using inverse power law and exponential relationships within the framework of a general log-linear Weibull life-stress statistical distribution. The obtained model is capable of extrapolating the membrane lifetime from accelerated test conditions to use level conditions during field operation. Based on typical conditions for the Whistler, British Columbia fuel cell transit bus fleet, the model predicts a stack lifetime of 17,500 h and a membrane leak initiation time of 9200 h. Validation performed with the aid of a field operated stack confirmed the initial goal of the model to predict membrane lifetime within 20% of the actual operating time.

Transit's leading edge : innovations in service and technology : issue paper 7

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-11-01

The Canadian Urban Transit Association is committed to raising awareness of the social, environmental and economic benefits of mass transit systems. Innovation is needed to address the challenges of attracting new riders, resolving fiscal imbalances, and meeting environmental concerns. This issue paper presents examples of how Canada's transit industry has used innovation to address the issue of climate change and fight smog. It includes a brief description of some of the ways that Canadian transit suppliers and transit systems are going green: Canada's bus builders are developing hybrid buses; Grand River Transit is improving air quality with clean diesel; Montreal's Transit Society is reducing emissions with biodiesel buses; Saskatoon Transit Service is using biodiesel buses; Laval's Transit Society is listening to customer complaints in an effort to reduce response times and improve customer service; Canadian Urban Transit Association is improving customer service; Transit Windsor is promoting a smog solution; Winnipeg Transit is working with employers to boost ridership; Trapeze Software Group is providing customers with quick and accurate trip itineraries; St. John's Transportation Commission has added solar-powered, light emitting diode illumination to bus stops; the City of Ottawa has an established transit priority measures; and, Infodev EDI Inc. has supplied automated high-technology solutions for passenger counting and vehicle location tracking to several Canadian transit systems. refs., figs.

Southern Nevada Alternative Fuels Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Hyde, Dan; Fast, Matthew

2009-12-31

The Southern Nevada Alternative Fuels Program is designed to demonstrate, in a day-to-day bus operation, the reliability and efficiency of a hydrogen bus operation under extreme conditions. By using ICE technology and utilizing a virtually emission free fuel, benefits to be derived include air quality enhancement and vehicle performance improvements from domestically produced, renewable energy sources. The project objective is to help both Ford and the City demonstrate and evaluate the performance characteristics of the E-450 H2ICE shuttle buses developed by Ford, which use a 6.8-liter supercharged Triton V-10 engine with a hydrogen storage system equivalent to 29 gallons of gasoline. The technology used during the demonstration project in the Ford buses is a modified internal combustion engine that allows the vehicles to run on 100% hydrogen fuel. Hydrogen gives a more thorough fuel burn which results in more power and responsiveness and less pollution. The resultant emissions from the tailpipe are 2010 Phase II compliant with NO after treatment. The City will lease two of these E-450 H2ICE buses from Ford for two years. The buses are outfitted with additional equipment used to gather information needed for the evaluation. Performance, reliability, safety, efficiency, and rider comments data will be collected. The method of data collection will be both electronically and manually. Emissions readings were not obtained during the project. The City planned to measure the vehicle exhaust with an emissions analyzer machine but discovered the bus emission levels were below the capability of their machine. Passenger comments were solicited on the survey cards. The majority of comments were favorable. The controllable issues encountered during this demonstration project were mainly due to the size of the hydrogen fuel tanks at the site and the amount of fuel that could be dispensed during a specified period of time. The uncontrollable issues encountered during this

COORDINATION OF THE WORK OF BUSES IN CITY ROUTES

Directory of Open Access Journals (Sweden)

Fuad DASHDAMIROV

2013-12-01

Full Text Available The paper studied the work of bus routes passing through a street. Optimality criterion was chosen for the development of appropriate models of effective work of buses on the land. The paper proposes a new model costing time passengers at bus stops. A method of technique was developed to coordinate the buses running on the combined section of route.

Alternative Fuel News: Official Publication of the Clean Cities Network and the Alternative Fuels Data Center, Vol. 5, No. 3

Energy Technology Data Exchange (ETDEWEB)

2001-11-01

A quarterly magazine with articles on alternative fuel school buses, the market growth of biodiesel fuel, National AFV Day 2002, model year 2002 alternative fuel passenger cars and light trucks, the Michelin Challenge Bibendum road rally, and advanced technology vehicles at Robins Air Force Base, the Top Ten Clean Cities coalitions for 2000, and AFVs on college campuses.

Natural Resource Canada`s fuel cell R and D program

Energy Technology Data Exchange (ETDEWEB)

Hammerli, M; Beck, N R [Natural Resources Canada, Ottawa, ON (Canada)

1998-05-01

The rationale for focusing fuel cell technology on the Ballard Proton exchange Membrane (PEM) system is provided. As well, research into other fuel cell types supported by Natural Resources Canada are discussed. Fuel cells are electrochemical devices that convert a fuel and an oxidant directly into electricity. Five fuel cell technologies use hydrogen as the fuel: (1) the alkaline fuel cell (AFC), (2) the proton exchange membrane fuel cell (PEMFC), (3) the phosphoric acid fuel cell (PAFC), (4) the molten carbonate fuel cell (MCFC), and (5) the solid oxide fuel cell (SOFC). The PEMFC is suitable for transportation applications because it does not contain a liquid electrolyte and it operates at about 80 degrees C. Trials on municipal bus systems are currently underway in Vancouver and Chicago. PEMFC stacks are supplied by Ballard Power Systems of Burnaby, BC, a recognized world leader in PEMFC technology. Daimler-Benz is demonstrating the methanol reformer on its NECAR-3, powered with a Ballard PEMFC. Ballard is also designing and producing two prototype fuel cell engines for the Ford Motor Company which will integrate them into its P2000 prototype vehicle platform. The Ballard technology is also suitable for distributed power generation up to about five MW, as well as for cogeneration, when fuelled with natural gas. Stuart Energy Systems (SES) has developed an advanced UNICELL-CLUSTER{sup T}M, which permits a direct coupling of the PV array to the electrolyser, a project which demonstrates the use of solar-electrolytic hydrogen production. SES is also designing a refuelling system for the BC Transit System in Vancouver for refuelling their three Zero Emission urban transit buses powered by Ballard fuel cell engines.

Mass concentrations of BTEX inside air environment of buses in Changsha, China

Energy Technology Data Exchange (ETDEWEB)

Chen, Xiaokai; Zhang, Guoqiang; Zhang, Quan [College of Civil Engineering, Hunan University, Changsha 410082, Hunan (China); Chen, Hong [College of Environmental Science and Engineering, Hunan University, Changsha 410082, Hunan (China)

2011-02-15

In order to estimate the mass concentrations of benzene (B), toluene (T), ethylbenzene (E) and xylenes (X) inside air environment of buses and to analyze the influencing factors of the BTEX pollution levels, 22 public buses were investigated in Changsha, China. The interior air was collected through activated charcoal adsorption tubes and then the air samples were analyzed with thermally desorbed gas chromatograph. The mass concentrations ranged from 21.3 to 106.4 {mu}g/m{sup 3} for benzene, from 53.5 to 266.0 {mu}g/m{sup 3} for toluene, from 19.6 to 95.9 {mu}g/m{sup 3} for ethylbenzene and from 46.9 to 234.8 {mu}g/m{sup 3} for xylenes. Their mean values were 68.7, 179.7, 62.5 and 151.8 {mu}g/m{sup 3}, respectively. The rates of buses tested where the interior concentrations exceeded the limit levels of Chinese Indoor Air Quality Standard were 45.5% for toluene and 13.6% for xylenes. The BTEX levels increased when in-car temperature or relative humidity rose, and decreased when car age or travel distance increased. The BTEX concentrations were higher in leather trims buses than in non-leather trims ones, in air-conditioned buses than in non-air-conditioned ones, and in high-grade buses than in low-grade ones. According to the analysis of multiple linear regression equation, car age and in-car temperature were two most important factors influencing the BTEX pollution levels in the cabins of public buses. (author)

Foothill Transit Battery Electric Bus Demonstration Results

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Prohaska, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kelly, Kenneth [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-01-27

Foothill Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL) to evaluate its fleet of Proterra battery electric buses (BEBs) in revenue service. The focus of this evaluation is to compare performance of the BEBs to that of conventional technology and to track progress over time toward meeting performance targets. This project has also provided an opportunity for DOE to conduct a detailed evaluation of the BEBs and charging infrastructure. This report provides data on the buses from April 2014 through July 2015. Data are provided on a selection of compressed natural gas buses as a baseline comparison.

Transition from uranium to denatured uranium/thorium fuel in an existing PWR

International Nuclear Information System (INIS)

Walters, M.A.

1982-01-01

The purpose of this research was to determine whether it is possible to make a gradual transition from uranium to denatured uranium/thorium (DUTH) fuel in an existing PWR by adding DUTH assemblies during each scheduled refueling and, if the transition is possible, to develop a general procedure for making it. The feasibility of the transition was established by identifying acceptable refueling schemes for a series of transition cores, and in the process, a method for identifying acceptable schemes evolved. The utility of the method was then demonstrated by applying it to a standard reactor operating under normal conditions. The vehicle used to examine proposed fuel mixtures and to select acceptable ones was a set of one-dimensional computer codes. The core was modeled as a set of five concentric fuel zones with a reflector. Fuel mixtures were proposed and the computer codes were used to determine whether a mixture was acceptable, i.e., whether it had the desired k-effective and flux and power distributions. The parameters allowed to vary in selection of proposed fuel mixtures were enrichment of fresh fuel assemblies, number of uranium and DUTH assemblies added during each refueling, and distribution of fuel in the core. Results of the research showed that a gradual transition is possible. Furthermore, there is a method that allows the identification of fuel mixtures that are likely to be acceptable. It requires the calculation of K-infinity for the entire proposed core and for some of its regions. These values of K-infinity and relationships developed in this research can be used to predict the flux distribution and the final k-effective for the proposed fuel mixture

Liquid-fueled SOFC power sources for transportation

Science.gov (United States)

Myles, K. M.; Doshi, R.; Kumar, R.; Krumpelt, M.

Traditionally, fuel cells have been developed for space or stationary terrestrial applications. As the first commercial 200-kW systems were being introduced by ONSI and Fuji Electric, the potentially much larger, but also more challenging, application in transportation was beginning to be addressed. As a result, fuel cell-powered buses have been designed and built, and R&D programs for fuel cell-powered passenger cars have been initiated. The engineering challenge of eventually replacing the internal combustion engine in buses, trucks, and passenger cars with fuel cell systems is to achieve much higher power densities and much lower costs than obtainable in systems designed for stationary applications. At present, the leading fuel cell candidate for transportation applications is, without question, the polymer electrolyte fuel cell (PEFC). Offering ambient temperature start-up and the potential for a relatively high power density, the polymer technology has attracted the interest of automotive manufacturers worldwide. But the difficulties of fuel handling for the PEFC have led to a growing interest in exploring the prospects for solid oxide fuel cells (SOFCs) operating on liquid fuels for transportation applications. Solid oxide fuel cells are much more compatible with liquid fuels (methanol or other hydrocarbons) and are potentially capable of power densities high enough for vehicular use. Two SOFC options for such use are discussed in this report.

Natural Gas as a Future Fuel for Heavy-Duty Vehicles

International Nuclear Information System (INIS)

Wai-Lin Litzke; James Wegrzyn

2001-01-01

In addition to their significant environmental impacts, medium-duty and heavy-duty (HD) vehicles are high volume fuel users. Development of such vehicles, which include transit buses, refuse trucks, and HD Class 6-8 trucks, that are fueled with natural gas is strategic to market introduction of natural gas vehicles (NGV). Over the past five years the Department of Energy's (DOE) Office of Heavy Vehicle Technologies (OHVT) has funded technological developments in NGV systems to support the growth of this sector in the highly competitive transportation market. The goals are to minimize emissions associated with NGV use, to improve on the economies of scale, and to continue supporting the testing and safety assessments of all new systems. This paper provides an overview of the status of major projects under a program supported by DOE/OHVT and managed by Brookhaven National Laboratory. The discussion focuses on the program's technical strategy in meeting specific goals proposed by the N GV industry and the government. Relevant projects include the development of low-cost fuel storage, fueling infrastructure, and HD vehicle applications

Alternative Fuel Vehicle Publications | Transportation Research | NREL

Science.gov (United States)

vehicle evaluations. Biodiesel Regional Transit District Effect of B20 and Low Aromatic Diesel on Transit Buses Operated on Biodiesel Blends. Kenneth Proc, Robb Barnitt, Robert Hayes, Matthew Ratcliff, and Robert McCormick. (2006) Operating Experience and Teardown Analysis for Engines Operated on Biodiesel

Reliability Evaluation Of The City Transport Buses Under Actual Conditions

Directory of Open Access Journals (Sweden)

Rymarz Joanna

2015-12-01

Full Text Available The purpose of this paper was to present a reliability comparison of two types of city transport buses. Case study on the example of the well-known brands of city buses: Solaris Urbino 12 and Mercedes-Benz 628 Conecto L used at Municipal Transport Company in Lublin was presented in details. A reliability index for the most failure parts and complex systems for the period of time failures was determined. The analysis covered damages of the following systems: engine, electrical system, pneumatic system, brake system, driving system, central heating and air-conditioning and doors. Reliability was analyzed based on Weibull model. It has been demonstrated, that during the operation significant reliability differences occur between the buses produced nowadays.

Optimized usage of NExBTL renewable diesel fuel - OPTIBIO

Energy Technology Data Exchange (ETDEWEB)

Nylund, N.-O. [VTT Technical Research Centre of Finland, Espoo (Finland); TEC TransEnergy Consulting Oy, Espoo (Finland)], email: nils-olof.nylund@vtt.fi, email: nils-olof.nylund@teconsulting.fi

2012-07-01

Buses are the backbone of many public transport systems, and typically have a long lifespan. Considering the need for switching to non-fossil fuels, municipalities increasingly want to raise the share of renewable fuels - also for their bus fleets - to reduce greenhouse gas emissions and fossil fuel imports. It is important for local decision-makers to understand which options are available and what the range of limitations and benefits of each. As the service life of buses is quite long, measures which can help improve the environmental performance of existing vehicles are important. When using conventional biodiesel there are technical limitations on how much fatty acid methyl ester (FAME) can be added to standard diesel fuel - in most cases replacement is below 10%. Further to this, some alternative fuels require new dedicated vehicles. The OPTIBIO project needed to explore how to optimise fuels that can be used in both existing and new vehicles, using high quality paraffinic renewable diesel (HVO) as fossil fuel replacement of up to 100%. The value, in addition to fuel replacement, would be the reduction of harmful emissions which are most crucial for urban air quality, namely nitrogen oxides and particulates.

Current Leads, Links and Buses

CERN Document Server

Ballarino, A

2014-01-01

Electrical transfer from a room temperature power source to a superconducting system is done via conventional or superconducting current leads and superconducting buses or links. The principles of optimization of these devices are presented, with emphasis on the cryogenic, electrical, and superconductor related aspects that drive choices for a system.

Current Leads, Links and Buses

Energy Technology Data Exchange (ETDEWEB)

Ballarino, A [European Organization for Nuclear Research, Geneva (Switzerland)

2014-07-01

Electrical transfer from a room temperature power source to a superconducting system is done via conventional or superconducting current leads and superconducting buses or links. The principles of optimization of these devices are presented, with emphasis on the cryogenic, electrical, and superconductor related aspects that drive choices for a system.

Using Checklists to Assess Your Transition to Alternative Fuels: A Technical Reference

Energy Technology Data Exchange (ETDEWEB)

Risch, C. E. [Argonne National Lab. (ANL), Argonne, IL (United States); Santini, D. J. [Argonne National Lab. (ANL), Argonne, IL (United States); Johnson, L. R. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-12-01

The Checklist for Transition to New Alternative Fuel(s) was published in September 2011 by Chuck Risch and Dan Santini. Many improvements, described below, have been incorporated into this current document, Checklists for Assessing the Transitions to New Highway Fuels.2 Further, the original authors and Larry Johnson, co-author of the current report, identified a need for a succinct version of the full report and prepared a brochure based on it to aid busy decisionmakers: Check It Out: Using Checklists to Assess Your Transition to Alternative Fuels.2 These checklists are tools for those stakeholders charged with determining a feasible alternative fuel or fuels for highway transportation systems of the future. The original had four major players whose needs had to be satisfied for a successful transition. The term “activist,” intended to encompass environmental and other special interests, was included in the “customers” category. Activists are customers of the government in the sense that they organize citizens to exert political pressure to regulate the design of vehicles, fuel infrastructure, and roadway networks. Many who evaluate alternative fuels view activists, particularly environmental activists, as a separate category. Further, “activist” has become a pejorative term to many people. Therefore, we have used the word “advocate” or “activist/advocate” instead. Thus, in this update we recognize that environmental and other activists/advocates have been--and will continue to be--a powerful force promoting change in the nature of the fuels that are used in transportation.

Transitioning aluminum clad spent fuels from wet to interim dry storage

International Nuclear Information System (INIS)

Louthan, M.R. Jr.; Iyer, N.C.; Sindelar, R.L.; Peacock, H.B. Jr.

1994-01-01

The United States Department of Energy (DOE) currently owns several hundred metric tons of aluminum clad, spent nuclear fuel and target assemblies. The vast majority of these irradiated assemblies are currently stored in water basins that were designed and operated for short term fuel cooling prior to fuel reprocessing. Recent DOE decisions to severely limit the reprocessing option have significantly lengthened the time of storage, thus increasing the tendency for corrosion induced degradation of the fuel cladding and the underlying core material. The portent of continued corrosion, coupled with the age of existing wet storage facilities and the cost of continuing basin operations, including necessary upgrades to meet current facility standards, may force the DOE to transition these wet stored, aluminum clad spent fuels to interim dry storage. The facilities for interim dry storage have not been developed, partially because fuel storage requirements and specifications for acceptable fuel forms are lacking. In spite of the lack of both facilities and specifications, current plans are to dry store fuels for approximately 40 to 60 years or until firm decisions are developed for final fuel disposition. The transition of the aluminum clad fuels from wet to interim dry storage will require a sequence of drying and canning operations which will include selected fuel preparations such as vacuum drying and conditioning of the storage atmosphere. Laboratory experiments and review of the available literature have demonstrated that successful interim dry storage may also require the use of fuel and canister cleaning or rinsing techniques that preclude, or at least minimize, the potential for the accumulation of chloride and other potentially deleterious ions in the dry storage environment. This paper summarizes an evaluation of the impact of fuel transitioning techniques on the potential for corrosion induced degradation of fuel forms during interim dry storage

Characterizing ultrafine particles and other air pollutants in and around school buses.

Science.gov (United States)

Zhu, Yifang; Zhang, Qunfang

2014-03-01

Increasing evidence has demonstrated toxic effects of ultrafine particles (UFP*, diameter emissions from idling school buses to air pollutant levels in and around school buses under different scenarios; 3. Retrofit tests to evaluate the performance of two retrofit systems, a diesel oxidation catalyst (DOC) muffler and a crankcase filtration system (CFS), on reducing tailpipe emissions and in-cabin air pollutant concentrations under idling and driving conditions; and 4. High efficiency particulate air (HEPA) filter air purifier tests to evaluate the effectiveness of in-cabin filtration. In total, 24 school buses were employed to cover a wide range of school buses commonly used in the United States. Real-time air quality measurements included particle number concentration (PNC), fine and UFP size distribution in the size range 7.6-289 nm, PM2.5 mass concentration, black carbon (BC) concentration, and carbon monoxide (CO) and carbon dioxide (CO2) concentrations. For in-cabin measurements, instruments were placed on a platform secured to the rear seats inside the school buses. For all other tests, a second set of instruments was deployed to simultaneously measure the ambient air pollutant levels. For tailpipe emission measurements, the exhaust was diluted and then measured by instruments identical to those used for the in-cabin measurements. The results show that when driving on roads, in-cabin PNC, fine and UFP size distribution, PM2.5, BC, and CO varied by engine age, window position, driving speed, driving route, and operating conditions. Emissions from idling school buses increased the PNC close to the tailpipe by a factor of up to 26.0. Under some circumstances, tailpipe emissions of idling school buses increased the in-cabin PNC by factors ranging from 1.2 to 5.8 in the 10-30 nm particle size range. Retrofit systems significantly reduced the tailpipe emissions of idling school buses. With both DOC and CFS installed, PNC in tailpipe emissions dropped by 20

Measurements of ultrafine particles and other vehicular pollutants inside school buses in South Texas

Science.gov (United States)

Zhang, Qunfang; Zhu, Yifang

2010-01-01

Increasing evidence has demonstrated toxic effects of vehicular emitted ultrafine particles (UFPs, diameter pollutants, especially UFPs, was measured inside four diesel-powered school buses. Two 1990 and two 2006 model year diesel-powered school buses were selected to represent the age extremes of school buses in service. Each bus was driven on two routine bus runs to study school children's exposure under different transportation conditions in South Texas. The number concentration and size distribution of UFPs, total particle number concentration, PM 2.5, PM 10, black carbon (BC), CO, and CO 2 levels were monitored inside the buses. The average total particle number concentrations observed inside the school buses ranged from 7.3 × 10 3 to 3.4 × 10 4 particles cm -3, depending on engine age and window position. When the windows were closed, the in-cabin air pollutants were more likely due to the school buses' self-pollution. The 1990 model year school buses demonstrated much higher air pollutant concentrations than the 2006 model year ones. When the windows were open, the majority of in-cabin air pollutants came from the outside roadway environment with similar pollutant levels observed regardless of engine ages. The highest average UFP concentration was observed at a bus transfer station where approximately 27 idling school buses were queued to load or unload students. Starting-up and idling generated higher air pollutant levels than the driving state. Higher in-cabin air pollutant concentrations were observed when more students were on board.

A seismic analysis of Korean standard PWR fuels under transition core conditions

International Nuclear Information System (INIS)

Kim, Hyeong Koo; Park, Nam Kyu; Jang, Young Ki; Kim, Jae Ik; Kim, Kyu Tae

2005-01-01

The PLUS7 fuel is developed to achieve higher thermal performance, burnup and more safety margin than the conventional fuel used in the Korean Standard Nuclear Plants (KSNPs) and to sustain structural integrity under increased seismic requirement in Korea. In this study, a series of seismic analysis have been performed in order to evaluate the structural integrity of fuel assemblies associated with seismic loads in the KSNPs under transition core conditions replacing the Guardian fuel, which is a resident fuel in the KSNP reactors, with the PLUS7 fuel. For the analysis, transition core seismic models have been developed, based on the possible fuel loading patterns. And the maximum impact forces on the spacer grid and various stresses acting on the fuel components have been evaluated and compared with the through-grid strength of spacer grids and the stress criteria specified in the ASME code for each fuel component, respectively. Then three noticeable parameters regarding as important parameters governing fuel assembly dynamic behavior are evaluated to clarify their effects on the fuel impact and stress response. As a result of the study, it has been confirmed that both the PLUS7 and the Guardian fuel sustain their structural integrity under the transition core condition. And when the damping ratio is constant, increasing the natural frequency of fuel assembly results in a decrease in impact force. The fuel assembly flexural stiffness has an effect increasing the stress of fuel assembly, but not the impact force. And the spacer grid stiffness is directly related with the impact force response. (author)

Thermal-hydraulic effects of transition to improved System 80TM fuel

International Nuclear Information System (INIS)

Rodack, T.; Joffre, P.F.; Kapoor, R.K.

2004-01-01

ABB CE's improved System 80 TM PWR fuel design includes GUARDIAN debris-resistant features and laser-welded Zircaloy grids. The GUARDIAN features include an Inconel grid with debris-filtering features located just above the Lower End Fitting, and a solid fuel rod bottom end cap that extends above the filtering features. Tests and analyses were done to establish the impact of these design improvements on fuel assembly hydraulic performance. Further analysis was done to determine the mixed core thermal-hydraulic performance as the transition is made over two fuel cycles to a full core of the improved System 80 TM fuel. Results confirm that the Thermal-Hydraulic (T-H) effects of the reduction in hydraulic resistance between the improved and resident fuel due to the laser-welded Zircaloy grids offsets the effects of the increased resistance GUARDIAN grid. Therefore, the mechanically improved System 80 TM fuel can be implemented with no net impact on Departure from Nucleate Boiling (DNB) margin in transition cores. (author)

10 CFR 73.37 - Requirements for physical protection of irradiated reactor fuel in transit.

Science.gov (United States)

2010-01-01

... fuel in transit. 73.37 Section 73.37 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PHYSICAL PROTECTION OF PLANTS AND MATERIALS Physical Protection of Special Nuclear Material in Transit § 73.37 Requirements for physical protection of irradiated reactor fuel in transit. (a) Performance objectives. (1...

Transitioning to a Hydrogen Future: Learning from the Alternative Fuels Experience

Energy Technology Data Exchange (ETDEWEB)

Melendez, M.

2006-02-01

This paper assesses relevant knowledge within the alternative fuels community and recommends transitional strategies and tactics that will further the hydrogen transition in the transportation sector.

Charging cost optimization for EV buses using neural network based energy predictor

NARCIS (Netherlands)

Nageshrao, S.P.; Jacob, J.; Wilkins, S.

2017-01-01

For conventional buses, based on the decades of their operational knowledge, public transport companies are able to optimize their cost of operation. However, with recent trend in the usage of electric buses, cost optimal operation can become challenging. In this paper an offline optimal charging

Next Generation Fuel Cell Technology for Passenger Cars and Buses

OpenAIRE

Mohrdieck, Dr.

2009-01-01

Daimler is presenting its latest fuel cell vehicle, the Mercedes-Benz B-Class F-CELL in 2009. Being one of the first series-produced fuel cell vehicles so far, the B-Class F-CELL will be a milestone on the road to commercialization of hydrogen-powered fuel cell vehicles. Equipped with advanced fuel cell technology it is suited for everyday operation and designed to fully meet customers´ expectations. From 2010 onwards, this zero emission vehicle is going to be operated by selected customers i...

An evaluation of alternative fuels usage by public transit agencies.

Science.gov (United States)

2009-12-01

The oil crisis of the 1970s forced Americans to reconsider using fossil fuels as a primary energy source. In : the public transit arena, private transit companies found themselves unable to compete in the urban : environment as rapidly rising oil pri...

Leveraging Fuel Subsidy Reform for Transition in Yemen

OpenAIRE

Clemens Breisinger; Wilfried Engelke; Olivier Ecker

2012-01-01

Yemen is currently undergoing a major political transition, yet many economic challenges—including fuel subsidy reform—remain highly relevant. To inform the transition process with respect to a potential subsidy reform, we use a dynamic computable general equilibrium and microsimulation model for Yemen; we show that overall growth effects of subsidy reduction are positive in general, but poverty can increase or decrease depending on reform design. A promising strategy for ...

Operational Assessment of Paralympics Transit Systems : Low-Floor Buses, Lift-Equipped Buses, and Signage

Science.gov (United States)

1997-02-01

From August 15-25, Atlanta hosted the paralympics, a world-class athletic competition for athletes with disabilities. To support the Paralympics, a specialized transit service was planned and deployed to service the travel needs of athletes, trainers...

On the issue of selecting technical and operational parameters for buses in urban passenger routes

Directory of Open Access Journals (Sweden)

Rudzinskyi V.V.

2017-10-01

Full Text Available Problems of a public transport bus service in urban areas were analyzed. The aim of the article is to determine actual operational parameters of buses during passenger transportation in Zhytomyr. Ways of determining technical and operational parameters of buses were developed using visual and tabular methods of city buses real-time speed and acceleration performance registration by GPS-monitoring system with the help of a communicational and informational intelligent transport system of the city. Experimental studies of city buses motion parameters were presented. A comprehensive survey of passenger traffic and conditions of public transport functioning in Zhytomyr was carried out. The values of technical and operational parameters of buses on city routes were obtained. Preliminarily conclusions and recommendations considering the criteria for selecting the optimal rolling stock for a bus network of the city were suggested.

The New Energy Buses in China

DEFF Research Database (Denmark)

Wang, Jingyu; Liu, Yingqi; Kokko, Ari

2013-01-01

With the advent of “low carbon” economy, new energy vehicles are increasingly favored by the Chinese government and manufacturers. New energy buses have become an important channel for the promotion of new energy utilizations. Based on the summary of policies, this paper conducts a thorough...

URBAN PUBLIC TRANSPORT WITH THE USE OF ELECTRIC BUSES – DEVELOPMENT TENDENCIES

Directory of Open Access Journals (Sweden)

Stanisław KRAWIEC

2016-12-01

Full Text Available The programing documents of the European Union determine the direction of transport systems development, including large cities and agglomerations. The context of these actions which aim to transform into ecologically clean and sustainable transport system is a significant reduction of greenhouse gas emissions. Assuming that public transport will significantly reduce the use of combustion-powered buses, studies on urban logistic enabling the use of electric buses for public transport are needed. The article presents the variants and scenarios for electric buses implementation in urban public transport, as well as the decision algorithm to support electric bus implementation based on technological, organisational, economic and ecological variables.

Alternative Fuel News: Official Publication of the Clean Cities Network and the Alternative Fuels Data Center, Vol. 6, No. 1

Energy Technology Data Exchange (ETDEWEB)

2002-07-01

Quarterly magazine with articles on auctions of used alternative fuel vehicles (AFVs), Royalty Enterprises of Ohio, and introducing AFVs in neglected urban areas. Plus Ford's new CNG school bus and electric buses in Connecticut.

Bacterial Quality of Drinking Water in Bushehr Intercity Buses in 2010

Directory of Open Access Journals (Sweden)

Dariush Ranjbar Vakilabadi

2012-12-01

Full Text Available Background and Objective: Road transportation and specifically bus travel accounts for the bulk of travel. Contaminated drinking water consumption is one of the issues that threaten health, and always there is pollution possibility in drinking water in buses. This study evaluated the microbial quality of consumed drinking water in buses and also compared it with available standards. Materials and Methods: This study is a cross-sectional study. By considering similar studies, 95% confidence interval and based on the samples size formula for tradition of proportion, 80 buses from 122 buses that entered Bushehr Passenger Depot from other cities or exited it were randomly selected. Over a three-month period, samples were taken from drinking water in these buses. Temperature, pH, residual chlorine, total coliform (TC, and fecal coliform (E. coli in each sample were measured in accordance with the standard method. Statistical analysis of the data was carried out with SPSS Version 16, and the t-test was performed for statistical difference. Results: The results showed that residual chlorine in 97.5% was zero and pH values of the samples were in the range of 6.8-8.7. TC and E. coli numbers in 12.5% and 8.8% of the samples were higher than those of standards, respectively. Conclusion: Use of ice, washing time of the drinking water tank (daily or weekly, and method of usage and storage of drinking water (with 20-liter tanks had significant effects on the bacterial loads of the drinking water in the tanks (p value <0.05. Some factors such as tank material, driver's education and age, type and model of the bus, filling time of the tank (daily or weekly, the method of filling and emptying the tank (complete clearing out of the tank or otherwise, and distance had no significant effect on the quality of the drinking water in the buses.

Analysis of fuel cycle strategies and U.S. transition scenarios

Energy Technology Data Exchange (ETDEWEB)

Wigeland, Roald; Taiwo, Temitope A.

2016-10-17

The nuclear fuel cycle Evaluation and Screening (E&S) study that was completed in October 2014 [1] enabled the identification of four fuel cycle groups that are considered most promising based on a set of nine evaluation criteria: (a) six benefit criteria of Nuclear Waste Management, Proliferation Risk, Nuclear Material Security Risk, Safety, Environmental Impact, Resource Utilization, and (b) three challenge criteria of Development and Deployment Risk, Institutional Issues, Financial Risk and Economics. The E&S study was conducted at a level of analysis that is "technology- neutral," that is, without consideration of specific technologies, but using the fundamental physics characteristics of each part of the fuel cycle. The study focused on the fuel cycle performance benefits at the fuel cycle equilibrium state, with only limited consideration of transition and deployment impacts. Common characteristics of the four most promising fuel cycle options include continuous recycle of all U/Pu or U/TRU, the use of fast-spectrum reactors, and no use of uranium enrichment once fuel cycle equilibrium has been established. The high-level wastes are mainly from processing of irradiated fuel, and there would be no disposal of any spent fuel. Building on the findings of the E&S study, additional studies have been conducted in the last two years following the information exchange meeting, the 13th IEMPT, which was held in Seoul, the Republic of Korea in 2014. Insights are presented from the recent studies on the benefits and challenges of recycling minor actinides, and transition considerations to some of the most promising fuel cycle options.

Leveraging Fuel Subsidy Reform for Transition in Yemen

Directory of Open Access Journals (Sweden)

Olivier Ecker

2012-10-01

Full Text Available Yemen is currently undergoing a major political transition, yet many economic challenges—including fuel subsidy reform—remain highly relevant. To inform the transition process with respect to a potential subsidy reform, we use a dynamic computable general equilibrium and microsimulation model for Yemen; we show that overall growth effects of subsidy reduction are positive in general, but poverty can increase or decrease depending on reform design. A promising strategy for a successful reform combines fuel subsidy reduction with direct income transfers to the poorest one-third of households during reform, and productivity-enhancing investment in infrastructure, plus fiscal consolidation. Public investments should be used for integrating economic spaces and restructuring of agricultural, industrial and service value chains in order to create a framework that encourages private-sector-led and job-creating growth.

Texas Hydrogen Highway Fuel Cell Hybrid Bus and Fueling Infrastructure Technology Showcase - Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hitchcock, David

2012-06-29

, and regenerative braking for battery charging. It uses a 19.3 kW Ballard PEM fuel cell, will store 12.6 kg of hydrogen at 350 Bar, and includes a 60 kWh battery storage system. The objectives of the project included the following: (a) To advance commercialization of hydrogen-powered transit buses and supporting infrastructure; (b) To provide public outreach and education by showcasing the operation of a 22-foot fuel cell hybrid shuttle bus and Texas first hydrogen fueling infrastructure; and (c) To showcase operation of zero-emissions vehicle for potential transit applications. As mentioned above, the project successfully demonstrated an early vehicle technology, the Ebus plug-in hybrid fuel cell bus, and that success has led to the acquisition of a more advanced vehicle that can take advantage of the same fueling infrastructure. Needed hydrogen station improvements have been identified that will enhance the capabilities of the fueling infrastructure to serve the new bus and to meet the transit agency needs. Over the course of this project, public officials, local government staff, and transit operators were engaged in outreach and education activities that acquainted them with the real world operation of a fuel cell bus and fueling infrastructure. Transit staff members in the Dallas/Ft. Worth region were invited to a workshop in Arlington, Texas at the North Central Texas Council of Governments to participate in a workshop on hydrogen and fuel cells, and to see the fuel cell bus in operation. The bus was trucked to the meeting for this purpose so that participants could see and ride the bus. Austin area transit staff members visited the fueling site in Austin to be briefed on the bus and to participate in a fueling demonstration. This led to further meetings to determine how a fuel cell bus and fueling station could be deployed at Capital Metro Transit. Target urban regions that expressed additional interest during the project in response to the outreach meetings and

Studies of self-pollution in diesel school buses: methodological issues.

Science.gov (United States)

Borak, Jonathan; Sirianni, Greg

2007-09-01

Considerable interest has focused on levels of exhaust emissions in the cabins of diesel-powered school buses and their possible adverse health effects. Significantly different policy and engineering issues would be raised if compelling evidence found that inc-cabin contamination was due to self-pollution from bus emissions, rather than ambient pollution, neighboring vehicles, and/or re-entrained road dust. We identified 19 reports from 11 studies that measured diesel exhaust particulate in the cabins of 58 school bus of various type. Studies were evaluated in light of their experimental design, their data quality, and their capacity to quantify self-pollution. Only one study had a true experimental design, comparing the same buses with and without emission controls, while four others used intentional tracers to quantify tail pipe and/or crankcase emissions. Although definitive data are still lacking, these studies suggest that currently available control technologies can nearly eliminate particulate self-pollution inside diesel school buses.

Transition cycle fuel management problems of NPP Krsko

International Nuclear Information System (INIS)

Petrovic, B.; Pevec, D.; Smuc, T.; Urli, N.

1989-01-01

Transition cycle fuel management problems are described and illustrated using results and experience attained during core reload design of NPP Krsko. Improved version of computer code package PSU-LEOPARD/Mcrac is successfully applied to NPP Krsko loading pattern design. (author)

Overview about the fuel cell bus demonstration programs CUTE, ECTOS and STEP

International Nuclear Information System (INIS)

Faltenbacher, M.; Fischer, M.; Eyerer, P.; Binder, M.; Schuckert, M.

2004-01-01

'Full text:' The paper will give an overview about the CUTE, ECTOS and STEP projects. The aim of the projects is to develop and demonstrate a emission-free and low-noise transport system, including the accompanying energy infrastructure, which has great potential for reducing the global greenhouse effect according to the Kyoto protocol, improving the quality of the atmosphere and life in densely populated areas and conserving fossil resources. For this purpose the application of the innovative hydrogen-based fuel cell technology is established by using fuel cell powered buses in an urban environment together with novel hydrogen production and support systems as part of a European Union wide demonstration scheme. The project demonstrates also to European Society the availability of the FC technology as a safe and reliable transportation technology. The major objectives are as follows: Demonstration of more than 20 fuel cell powered regular service buses over a period of two years in several European inner city areas to illustrate the different operating conditions to be found in Europe; Design, construction and operation of the necessary infrastructure for hydrogen production, including the required refuelling stations; Collection of findings concerning the construction and operating behaviour of hydrogen production for mobile use, and exchange of experiences including bus operation under differing conditions among the numerous participating companies; and, the research work of IKP and PE comprises the ecological analysis of the entire life cycle and comparison with conventional alternatives (diesel driven buses, CNG-buses). It also includes the economical analysis of the hydrogen infrastructure. First experiences from CUTE and ECTOS were presented. (author)

A Framework for Assessing Feasibility of Transit-Oriented Development (TOD) Project Sites

Science.gov (United States)

2017-09-01

After the Second World War, the United States saw a decline in ridership on transit systems, which eventually resulted in the dismantling and abandonment of many rail systems. The primary mode of public transportation shifted from transit to buses. I...

Commuters’ Exposure to Particulate Matter Air Pollution Is Affected by Mode of Transport, Fuel Type, and Route

Science.gov (United States)

Zuurbier, Moniek; Hoek, Gerard; Oldenwening, Marieke; Lenters, Virissa; Meliefste, Kees; van den Hazel, Peter; Brunekreef, Bert

2010-01-01

Background Commuters are exposed to high concentrations of air pollutants, but little quantitative information is currently available on differences in exposure between different modes of transport, routes, and fuel types. Objectives The aim of our study was to assess differences in commuters’ exposure to traffic-related air pollution related to transport mode, route, and fuel type. Methods We measured particle number counts (PNCs) and concentrations of PM2.5 (particulate matter ≤ 2.5 μm in aerodynamic diameter), PM10, and soot between June 2007 and June 2008 on 47 weekdays, from 0800 to 1000 hours, in diesel and electric buses, gasoline- and diesel-fueled cars, and along two bicycle routes with different traffic intensities in Arnhem, the Netherlands. In addition, each-day measurements were taken at an urban background location. Results We found that median PNC exposures were highest in diesel buses (38,500 particles/cm3) and for cyclists along the high-traffic intensity route (46,600 particles/cm3) and lowest in electric buses (29,200 particles/cm3). Median PM10 exposure was highest from diesel buses (47 μg/m3) and lowest along the high- and low-traffic bicycle routes (39 and 37 μg/m3). The median soot exposure was highest in gasoline-fueled cars (9.0 × 10−5/m), diesel cars (7.9 × 10−5/m), and diesel buses (7.4 × 10−5/m) and lowest along the low-traffic bicycle route (4.9 × 10−5/m). Because the minute ventilation (volume of air per minute) of cyclists, which we estimated from measured heart rates, was twice the minute ventilation of car and bus passengers, we calculated that the inhaled air pollution doses were highest for cyclists. With the exception of PM10, we found that inhaled air pollution doses were lowest for electric bus passengers. Conclusions Commuters’ rush hour exposures were significantly influenced by mode of transport, route, and fuel type. PMID:20185385

Design of durability test protocol for vehicular fuel cell systems operated in power-follow mode based on statistical results of on-road data

Science.gov (United States)

Xu, Liangfei; Reimer, Uwe; Li, Jianqiu; Huang, Haiyan; Hu, Zunyan; Jiang, Hongliang; Janßen, Holger; Ouyang, Minggao; Lehnert, Werner

2018-02-01

City buses using polymer electrolyte membrane (PEM) fuel cells are considered to be the most likely fuel cell vehicles to be commercialized in China. The technical specifications of the fuel cell systems (FCSs) these buses are equipped with will differ based on the powertrain configurations and vehicle control strategies, but can generally be classified into the power-follow and soft-run modes. Each mode imposes different levels of electrochemical stress on the fuel cells. Evaluating the aging behavior of fuel cell stacks under the conditions encountered in fuel cell buses requires new durability test protocols based on statistical results obtained during actual driving tests. In this study, we propose a systematic design method for fuel cell durability test protocols that correspond to the power-follow mode based on three parameters for different fuel cell load ranges. The powertrain configurations and control strategy are described herein, followed by a presentation of the statistical data for the duty cycles of FCSs in one city bus in the demonstration project. Assessment protocols are presented based on the statistical results using mathematical optimization methods, and are compared to existing protocols with respect to common factors, such as time at open circuit voltage and root-mean-square power.

76 FR 46892 - Agency Information Collection Activity Under OMB Review

Science.gov (United States)

2011-08-03

... intention to request the Office of Management and Budget's (OMB) approval for the following new information... development and deployment of clean fuel and advanced propulsion technologies for transit buses. To meet program oversight responsibilities, FTA needs information on the operation and performance of clean fuel...

Business Case for Fuel Cells 2016

Energy Technology Data Exchange (ETDEWEB)

Curtin, Sandra [Fuel Cell and Hydrogen Energy Association, Washington, DC (United States); Gangi, Jennifer [Fuel Cell and Hydrogen Energy Association, Washington, DC (United States); Benjamin, Thomas G. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-12-01

The report provides an overview of recent private sector fuel cell installations at U.S. businesses as of December 31, 2016. This list is by no means exhaustive. Over the past few decades, hundreds of thousands of fuel cells have been installed around the world, for primary or backup power, as well as in various other applications including portable and emergency backup power. Fuel cells have also been deployed in other applications such as heat and electricity for homes and apartments, material handling, passenger vehicles, buses, and remote, off-grid sites.

Unit Monitors Manchester-Format Data Buses

Science.gov (United States)

Amador, Jose J.

1994-01-01

Circuit card converts data signals into convenient hexadecimal form for troubleshooting. Bus-monitoring unit converts data signals from Manchester II format used on data bus into hexadecimal format. Monitoring circuit causes hexadecimal words to display on video terminal, where test engineer compares them with hexadecimal records for troubleshooting. Circuit monitors one bus or two buses simultaneously.

Kicking the habit[Hydrogen fuel

Energy Technology Data Exchange (ETDEWEB)

Jones, N.; Lawton, G.; Pearce, F.

2000-11-25

This article focuses on the use of clean non-polluting hydrogen fuel as opposed to the use of fossil fuels which ties western nations to the Middle East. Details are given of Iceland's plans to use hydrogen fuelled buses, cars, trucks and trawlers, car manufacturers' options of using internal combustion engines burning hydrogen and hydrogen fuel cells, and the production of hydrogen using electrolysis of water and steam reforming of hydrocarbons. The 'Green Dream' of pollution-free hydrogen production, the use of solar energy for renewable hydrogen production in California, and problems associated with hydrogen storage are discussed.

Buse_Francisella and free-living amoebae data sets

Data.gov (United States)

U.S. Environmental Protection Agency — Co-infection data in the form of colony forming units and amoeba cell counts. This dataset is associated with the following publication: Buse , H., F. Schaefer, and...

The California experience : lessons learned and prospects for the future

Energy Technology Data Exchange (ETDEWEB)

Levin, J. [AC Transit, Oakland, CA (United States)

2007-07-01

AC Transit operates 650 hydrogen-powered mass transit buses that serve 1.5 million people in 13 cities in California. This presentation discussed the impact of the buses on public health, quality of life and cost savings. Hydrogen has been touted as a diversified and renewable energy supply that can provide energy independence and reduction in global warming. Mass transit systems have proven to be well suited for testing the limits of hydrogen-powered vehicles primarily because of the centralized fueling and maintenance structure. AC Transit began ZEbus testing in November 1999 and became involved in the California Fuel Cell Partnership in 2000. The NeBus test was performed in 2000, followed by the ISE/UTC Thor Bus in 2003/2004. The governor's inauguration of the zero emission buses was in January 2007. The lessons learned from the California experience were: (1) motivation must be for the right reason, (2) a champion is required, (3) community and political support is required, (4) capital investment is required, (5) a strong management team is required, (6) partners must be chosen wisely, (7) the end user or customer must be allowed to drive the design, (8) inform the public about plans, (9) evaluation is essential to industry-wide application, (10) all resources must be considered for outreach and education, (11) optimism is required to surpass challenges, (12) the technology should be promoted for future generations. The presentation concluded with comments on market value of hydrogen and fuel cell vehicles, their fuel efficiency, reliability and durability. tabs., figs.

Speeding the transition: Designing a fuel-cell hypercar

Energy Technology Data Exchange (ETDEWEB)

Williams, B.D.; Moore, T.C.; Lovins, A.B. [Rocky Mountain Inst., Snowmass, CO (United States). Hypercar Center

1997-12-31

A rapid transformation now underway in automotive technology could accelerate the transition to transportation powered by fuel cells. Ultralight, advanced-composite, low-drag, hybrid-electric hypercars--using combustion engines--could be three- to fourfold more efficient and one or two orders of magnitude cleaner than today`s cars, yet equally safe, sporty, desirable, and (probably) affordable. Further, important manufacturing advantages--including low tooling and equipment costs, greater mechanical simplicity, autobody parts consolidation, shorter product cycles, and reduced assembly effort and space--permit a free-market commercialization strategy. This paper discusses a conceptual hypercar powered by a proton-exchange-membrane fuel cell (PEMFC). It outlines the implications of platform physics and component selection for the vehicle`s mass budget and performance. The high fuel-to-traction conversion efficiency of the hypercar platform could help automakers overcome the Achilles` heel of hydrogen-powered vehicles: onboard storage. Moreover, because hypercars would require significantly less tractive power, and even less fuel-cell power, they could adopt fuel cells earlier, before fuel cells` specific cost, mass, and volume have fully matured. In the meantime, commercialization in buildings can help prepare fuel cells for hypercars. The promising performance of hydrogen-fueled PEMFC hypercars suggests important opportunities in infrastructure development for direct-hydrogen vehicles.

Cool Science: K-12 Climate Change Art Displayed on Buses

Science.gov (United States)

Chen, R. F.; Lustick, D. S.; Lohmeier, J.; Thompson, S. R.

2015-12-01

Cool science is an art contest where K12 students create placards (7" x 22") to educate the public about climate change. Students are prompted to create their artwork in response to questions such as: What is the evidence for climate change? How does climate change impact your local community? What can you do to reduce the impacts of climate change? In each of three years, 500-600 student entrees have been submitted from more than 12 school districts across Massachusetts. A panel of judges including scientists, artists, rapid transit representatives, and educators chooses elementary, middle, and high school winners. Winners (6), runners-up (6), and honorable mentions (12) and their families and teachers are invited to an annual Cool Science Award Ceremony to be recognized and view winning artwork. All winning artwork is posted on the Cool Science website. The winning artwork (2 per grade band) is converted into placards (11" x 28") and posters (2.5' x 12') that are placed on the inside (placards) and outside (posters) of buses. Posters are displayed for one month. So far, Cool Science was implemented in Lowell, MA where over 5000 public viewers see the posters daily on the sides of Lowell Rapid Transit Authority (LRTA) buses, making approximately 1,000,000 impressions per year. Cool Science acts to increase climate literacy in children as well as the public, and as such promotes intergenerational learning. Using art in conjunction with science learning about climate change appears to be effective at engaging not just traditionally high achieving science students, but also those interested in the creative arts. Hearing winners' stories about how they created their artwork and what this contest meant to them supports the idea that Cool Science attracts a wide diversity of students. Parents discuss climate change with their children. Multiple press releases announcing the winners further promotes the awareness of climate change throughout school districts and their

Using Task Clarification, Goal Setting, and Feedback to Decrease Table Busing Times in a Franchise Pizza Restaurant

Science.gov (United States)

Amigo, Seth; Smith, Andrew; Ludwig, Timothy

2008-01-01

The current study investigated the effects of task-clarification, and manager verbal and graphic feedback on employee busing times at a pizza restaurant. Using an ABC design, task-clarification was provided in a memo, which described the process, priority, and goal time of busing. The busing time decreased slightly, from an average of 315 seconds…

Foothill Transit Battery Electric Bus Demonstration Results: Second Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jeffers, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-06-28

This report summarizes results of a battery electric bus (BEB) evaluation at Foothill Transit, located in the San Gabriel and Pomona Valley region of Los Angeles County, California. Foothill Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory to evaluate its fleet of Proterra BEBs in revenue service. The focus of this evaluation is to compare performance of the BEBs to that of conventional technology and to track progress over time toward meeting performance targets. This project has also provided an opportunity for DOE to conduct a detailed evaluation of the BEBs and charging infrastructure. This is the second report summarizing the results of the BEB demonstration at Foothill Transit and it provides data on the buses from August 2015 through December 2016. Data are provided on a selection of compressed natural gas buses as a baseline comparison.

NOx reduction in diesel fuel flames by additions of water and CO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Li, S.C. [Univ. of California, San Diego, La Jolla, CA (United States)

1997-12-31

Natural gas has the highest heating value per unit mass (50.1 MJ/kg, LHV) of any of the hydrocarbon fuels (e.g., butane, liquid diesel fuel, gasoline, etc.). Since it has the lowest carbon content per unit mass, combustion of natural gas produces much less carbon dioxide, soot particles, and oxide of nitrogen than combustion of liquid diesel fuel. In view of anticipated strengthening of regulations on pollutant emissions from diesel engines, alternative fuels, such as compressed natural gas (CNG) and liquefied natural gas (LNG) have been experimentally introduced to replace the traditional diesel fuels in heavy-duty trucks, transit buses, off-road vehicles, locomotives, and stationary engines. To help in applying natural gas in Diesel engines and increasing combustion efficiency, the emphasis of the present paper is placed on the detailed flame chemistry of methane-air combustion. The present work is the continued effort in finding better methods to reduce NO{sub x}. The goal is to identify a reliable chemical reaction mechanism for natural gas in both premixed and diffusion flames and to establish a systematic reduced mechanism which may be useful for large-scale numerical modeling of combustion behavior in natural gas engines.

Optimization analysis of the nuclear fuel cycle transition to the last core

International Nuclear Information System (INIS)

Rebollo, L.; Blanco, J.

2001-01-01

The Zorita NPP was the first Spanish commercial nuclear reactor connected to the grid. It is a 160 MW one loop PWR, Westinghouse design, owned by UFG, in operation since 1968. The configuration of the reactor core is based on 69 fuel elements type 14 x 14, the standard reload of the present equilibrium cycle being based on 16 fuel elements with 3.6% enrichment in 235 U. In order to properly plan the nuclear fuel management of the transition cycles to its end of life, presently foreseen by 2008, an based on the non-reprocessing option required by the policy of the Spanish Administration, a technical-economical optimization analysis has been performed. As a result, a fuel management strategy has been defined looking for getting simultaneously the minimum integral fuel cost of the transition from the present equilibrium cycle to the last core, as well as the minimum residual worth of the fuel remaining in the core after the final outage. Based on the ''lessons learned'' derived from the study, the time margin for the decision making has been determined, and a planning of the nuclear fuel supply for the transition reloads, specifying both the number of fuel elements and their enrichment in 235 U, as been prepared. Finally, based on the calculated economical worth of the partially burned fuel of the last core, after the end of its operation cycle, a financial cover for yearly compensation from now on of the foreseen final lost has been elaborated. Most of the conceptual conclusions obtained are applicable to the other commercial nuclear reactors in operation owned by UFG, so that they are understood to be of general interest and broad application to commercial PWR. (author)

Fuel economy and range estimates for fuel cell powered automobiles

Energy Technology Data Exchange (ETDEWEB)

Steinbugler, M.; Ogden, J. [Princeton Univ., NJ (United States)

1996-12-31

While a number of automotive fuel cell applications have been demonstrated, including a golf cart, buses, and a van, these systems and others that have been proposed have utilized differing configurations ranging from direct hydrogen fuel cell-only power plants to fuel cell/battery hybrids operating on reformed methanol. To date there is no clear consensus on which configuration, from among the possible combinations of fuel cell, peaking device, and fuel type, is the most likely to be successfully commercialized. System simplicity favors direct hydrogen fuel cell vehicles, but infrastructure is lacking. Infrastructure favors a system using a liquid fuel with a fuel processor, but system integration and performance issues remain. A number of studies have analyzed particular configurations on either a system or vehicle scale. The objective of this work is to estimate, within a consistent framework, fuel economies and ranges for a variety of configurations using flexible models with the goal of identifying the most promising configurations and the most important areas for further research and development.

Developing a discrete event simulation model for university student shuttle buses

Science.gov (United States)

Zulkepli, Jafri; Khalid, Ruzelan; Nawawi, Mohd Kamal Mohd; Hamid, Muhammad Hafizan

2017-11-01

Providing shuttle buses for university students to attend their classes is crucial, especially when their number is large and the distances between their classes and residential halls are far. These factors, in addition to the non-optimal current bus services, typically require the students to wait longer which eventually opens a space for them to complain. To considerably reduce the waiting time, providing the optimal number of buses to transport them from location to location and the effective route schedules to fulfil the students' demand at relevant time ranges are thus important. The optimal bus number and schedules are to be determined and tested using a flexible decision platform. This paper thus models the current services of student shuttle buses in a university using a Discrete Event Simulation approach. The model can flexibly simulate whatever changes configured to the current system and report its effects to the performance measures. How the model was conceptualized and formulated for future system configurations are the main interest of this paper.

Alternative transportation fuels in the USA: government hydrogen vehicle programs

International Nuclear Information System (INIS)

Cannon, J.S.

1993-01-01

The linkage between natural gas-based transportation and hydrogen-based transportation strategies, two clean burning gaseous fuels, provides a strong policy rationale for increased government sponsorship of hydrogen vehicle research and demonstration programs. Existing federal and state government hydrogen vehicle projects are discussed in this paper: research at the NREL, alternate-fueled buses, Renewable Hydrogen for the State of Hawaii program, New York state alternative transportation fuels program, Colorado program. 9 refs

Analysis, operation and maintenance of a fuel cell/battery series-hybrid bus for urban transit applications

Science.gov (United States)

Bubna, Piyush; Brunner, Doug; Gangloff, John J.; Advani, Suresh G.; Prasad, Ajay K.

The fuel cell hybrid bus (FCHB) program was initiated at the University of Delaware in 2005 to demonstrate the viability of fuel cell vehicles for transit applications and to conduct research and development to facilitate the path towards their eventual commercialization. Unlike other fuel cell bus programs, the University of Delaware's FCHB design features a battery-heavy hybrid which offers multiple advantages in terms of cost, performance and durability. The current fuel cell hybrid bus is driven on a regular transit route at the University of Delaware. The paper describes the baseline specifications of the bus with a focus on the fuel cell and the balance of plant. The fuel cell/battery series-hybrid design is well suited for urban transit routes and provides key operational advantages such as hydrogen fuel economy, efficient use of the fuel cell for battery recharging, and regenerative braking. The bus is equipped with a variety of sensors including a custom-designed cell voltage monitoring system which provide a good understanding of bus performance under normal operation. Real-time data collection and analysis have yielded key insights for fuel cell bus design optimization. Results presented here illustrate the complex flow of energy within the various subsystems of the fuel cell hybrid bus. A description of maintenance events has been included to highlight the issues that arise during general operation. The paper also describes several modifications that will facilitate design improvements in future versions of the bus. Overall, the fuel cell hybrid bus demonstrates the viability of fuel cells for urban transit applications in real world conditions.

Concentrations of volatile organic compounds, carbon monoxide, carbon dioxide and particulate matter in buses on highways in Taiwan

Science.gov (United States)

Hsu, Der-Jen; Huang, Hsiao-Lin

2009-12-01

Although airborne pollutants in urban buses have been studied in many cities globally, long-distance buses running mainly on highways have not been addressed in this regard. This study investigates the levels of volatile organic compounds (VOCs), carbon monoxide (CO), carbon dioxide (CO 2) and particulate matter (PM) in the long-distance buses in Taiwan. Analytical results indicate that pollutants levels in long-distance buses are generally lower than those in urban buses. This finding is attributable to the driving speed and patterns of long-distance buses, as well as the meteorological and geographical features of the highway surroundings. The levels of benzene, toluene, ethylbenzene and xylene (BTEX) found in bus cabins exceed the proposed indoor VOC guidelines for aromatic compounds, and are likely attributable to the interior trim in the cabins. The overall average CO level is 2.3 ppm, with higher average level on local streets (2.9 ppm) than on highways (2.2 ppm). The average CO 2 level is 1493 ppm, which is higher than the guideline for non-industrial occupied settings. The average PM level in this study is lower than those in urban buses and IAQ guidelines set by Taiwan EPA. However, the average PM 10 and PM 2.5 is higher than the level set by WHO. Besides the probable causes mentioned above, fewer passenger movements and less particle re-suspension from bus floor might also cause the lower PM levels. Measurements of particle size distribution reveal that more than 75% of particles are in submicron and smaller sizes. These particles may come from the infiltration from the outdoor air. This study concludes that air exchange rates in long-distance buses should be increased in order to reduce CO 2 levels. Future research on long-distance buses should focus on the emission of VOCs from brand new buses, and the sources of submicron particles in bus cabins.

Comparison of Gasoline and Primary Reference Fuel in the Transition from HCCI to PPC

KAUST Repository

Li, Changle

2017-10-10

Our previous research investigated the sensitivity of combustion phasing to intake temperature and injection timing during the transition from homogeneous charge compression ignition (HCCI) to partially premixed combustion (PPC) fuelled with generic gasoline. The results directed particular attention to the relationship between intake temperature and combustion phasing which reflected the changing of stratification level with the injection timing. To confirm its applicability with the use of different fuels, and to investigate the effect of fuel properties on stratification formation, primary reference fuels (PRF) were tested using the same method: a start of injection sweep from -180° to -20° after top dead center with constant combustion phasing by tuning the intake temperature. The present results are further developed compared with those of our previous work, which were based on generic gasoline. In the present work, a three-stage fuel-air stratification development process was observed during the transition from HCCI to PPC. Moreover, a transition stage was observed between the HCCI and PPC stages. Within this transition stage, both the combustion and emission characteristics deteriorated. The allocation of this transition area was mainly determined by the geometric design of the fuel injector and combustion chamber. Some differences in charge stratification were observed between the PRF and gasoline. The NO emissions of the PRF were comparable to those of gasoline. However, the NO emissions surged during the transition stage, indicating that the PRF combustion was probably more stratified. The soot emissions from PRF and gasoline were both much higher in the PPC than the HCCI mode, though the PRF produced much less soot than did gasoline in the PPC mode.

The effects of urban driving conditions on the operating characteristics of conventional and hybrid electric city buses

International Nuclear Information System (INIS)

Soylu, Seref

2014-01-01

Highlights: • Operating characteristics of conventional and hybrid electric buses were examined. • Recovery of braking energy offers an excellent opportunity to improve fuel economy. • Speed and altitude profiles of routes have dramatic impacts on the energy recovery. • Capacity of the auxiliary power source has a dramatic impact on the energy recovery. • Round-trip efficiency of the regenerative braking system was calculated to be 27%. - Abstract: The basic operating characteristics of a conventional bus (CB) and a hybrid electric bus (HEB) were examined under urban driving conditions. To perform this examination, real-time operating data from the buses were collected on the Campus-Return route of the Sakarya Municipality. The main characteristics examined were the traction, braking, engine, engine generator unit (EGU), motor/generator (M/G), and ultracapacitor (Ucap) energies and efficiencies of the buses. The route elevation profile and the frequency of stop-and-go operations of the buses were found to have dramatic impacts on the braking and traction energies of the buses. The declining profile of the Campus-Return route provided an excellent opportunity for energy recovery by the regenerative braking system of the HEB. However, owing to the limits on the capacities and efficiencies of the hybrid drive train components and the Ucap, the bus braking energies were not recovered completely. Braking energies as high as 2.2 kW h per micro-trip were observed, but less than 1 kW h of braking energy per micro-trip was converted to electricity by the M/G; the rest of the braking energy was wasted in frictional braking. The maximum energy recovered and stored in the Ucap per micro-trip was 0.5 kW h, but the amount of energy recovered and stored per micro-trip was typically less than 0.2 kW h for the entire route. The cumulative braking energy recovered and stored in the Ucap for the Campus-Return route was 52% of the available brake energy, which was 13.02 kW h

Fifth annual report to congress. Federal alternative motor fuels programs

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

This report presents the status of the US Department of Energy`s alternative fuel vehicle demonstration and performance tracking programs being conducted in accordance with the Energy Policy and Conservation Act. These programs comprise the most comprehensive data collection effort ever undertaken on alternative transportation fuels and alternative fuel vehicles. The report summarizes tests and results from the fifth year. Electric vehicles are not included in these programs, and the annual report does not include information on them. Since the inception of the programs, great strides have been made in developing commercially viable alternative fuel vehicle technologies. However, as is the case in the commercialization of all new technologies, some performance problems have been experienced on vehicles involved in early demonstration efforts. Substantial improvements have been recorded in vehicle practicality, safety, and performance in real-world demonstrations. An aspect of particular interest is emissions output. Results from light duty alternative fuel vehicles have demonstrated superior inservice emissions performance. Heavy duty alternative fuel vehicles have demonstrated dramatic reductions in particulate emissions. However, emissions results from vehicles converted to run on alternative fuel have not been as promising. Although the technologies available today are commercially viable in some markets, further improvements in infrastructure and economics will result in greater market expansion. Information is included in this report on light and heavy duty vehicles, transit buses, vehicle conversions, safety, infrastructure support, vehicle availability, and information dissemination.

Attributional and consequential environmental assessment of using waste cooking oil- and poultry fat-based biodiesel blends in urban buses: a real-world operation condition study

Directory of Open Access Journals (Sweden)

Mohammad Rajaeifar

2017-09-01

Full Text Available Urban public transportation sector in general is heavily dependent on fossil-oriented fuels, e.g., diesel. Given the fact that a major proportion of urban pollution and the consequent threats towards public health are attributed to this sector, serious efforts at both technical and political levels have been being made to introduce less-polluting fueling regimes, e.g., partial replacement of diesel with biodiesel. In line with that, the present study was aimed at evaluating the emissions attributed to 5% blends of waste cooking oil (WCO and poultry fat (PF biodiesel fuels (i.e., B5-WCO and B5-PF fuel blends when used in urban buses during idle operation mode. Moreover, the attributional and consequential environmental impacts of using these fuel blends were also investigated through a well to wheel life cycle assessment (LCA by considering the real-world condition combustion data using ten urban buses. The findings of the ALCA revealed that the application of 1 L B5-WCO fuel blend could potentially reduce the environmental burdens in human health, ecosystem quality, and resources damage categories compared with using the B5-PF fuel blend. The situation was opposite for climate change damage category in which using 1 L B5-PF fuel blend had a lower impact on the environment. Overall, the environmental hotspots in the B5-WCO and B5-PF life cycles were identified as the combustion stage as well as the diesel production and transportation. From the consequential perspective, using 1 L B5-WCO fuel blend could potentially decrease the environmental burdens in human health, ecosystem quality, and resources damage categories. While, the situation was different for climate change damage category where using 1 L B5-PF fuel blend could have a lower impact on the environment. In conclusion, using B5-WCO fuel blend as an alternative for diesel could be an environmentally-friendly decision for the Iranian urban transportation sector at the policy level as long

Analysis, operation and maintenance of a fuel cell/battery series-hybrid bus for urban transit applications

Energy Technology Data Exchange (ETDEWEB)

Bubna, Piyush; Brunner, Doug; Gangloff, John J. Jr.; Advani, Suresh G.; Prasad, Ajay K. (Center for Fuel Cell Research, Department of Mechanical Engineering, University of Delaware, Newark, DE 19716 United States)

2010-06-15

The fuel cell hybrid bus (FCHB) program was initiated at the University of Delaware in 2005 to demonstrate the viability of fuel cell vehicles for transit applications and to conduct research and development to facilitate the path towards their eventual commercialization. Unlike other fuel cell bus programs, the University of Delaware's FCHB design features a battery-heavy hybrid which offers multiple advantages in terms of cost, performance and durability. The current fuel cell hybrid bus is driven on a regular transit route at the University of Delaware. The paper describes the baseline specifications of the bus with a focus on the fuel cell and the balance of plant. The fuel cell/battery series-hybrid design is well suited for urban transit routes and provides key operational advantages such as hydrogen fuel economy, efficient use of the fuel cell for battery recharging, and regenerative braking. The bus is equipped with a variety of sensors including a custom-designed cell voltage monitoring system which provide a good understanding of bus performance under normal operation. Real-time data collection and analysis have yielded key insights for fuel cell bus design optimization. Results presented here illustrate the complex flow of energy within the various subsystems of the fuel cell hybrid bus. A description of maintenance events has been included to highlight the issues that arise during general operation. The paper also describes several modifications that will facilitate design improvements in future versions of the bus. Overall, the fuel cell hybrid bus demonstrates the viability of fuel cells for urban transit applications in real world conditions. (author)

Transition Towards a Sustainable Nuclear Fuel Cycle

International Nuclear Information System (INIS)

McCarthy, K.; Romanello, V.; Schwenk-Ferrero, A.; Vezzoni, B.; Gabrielli, F.; Maschek, W.; Rineiski, A.; Salvatores, M.

2013-01-01

To support the evaluation of R and D needs and relevant technology requirements for future nuclear fuel cycles, the OECD/NEA WPFC Expert Group on Advanced Fuel Cycle Scenarios was created in 2010, replacing the WPFC Expert Group on Fuel Cycle Transition Scenario Studies (1) to assemble, organise and understand the scientific issues of advanced fuel cycles and (2) to provide a framework for assessing specific national needs related to the implementation of advanced fuel cycles. In this framework, a simulation of world transition scenarios towards possible future fuel cycles with fast reactors has been performed, using both a homogeneous and a heterogeneous approach involving different world regions. In fact, it has been found that a crucial feature of any world scenario study is to provide not only trends for an idealised 'homogeneous' description of the world, but also trends for different regions in the world, selected with simple criteria (mostly of geographical type), in order to apply different hypotheses to energy demand growth, different fuel cycle strategies and different reactor types implementation in the different regions. This approach was an attempt to avoid focusing on selected countries, in particular on those where no new spectacular energy demand growth is expected, but to provide trends and conclusions that account for the features of countries that will be major future players in the world's energy development. The heterogeneous approach considered a subdivision of the world in four main macro-regions (where countries have been grouped together according to their economic development dynamics). An original global electricity production envelope was used in simulations and a specific regional energy share was defined. In the regional approach two different fuel cycles were analysed: a once-through LWR cycle was used as the reference and a transition to fast reactor closed cycle to enable a better management of resources and minimisation of waste

Confusion errors and false manoeuvres at power buses

International Nuclear Information System (INIS)

Cernes, A.

1985-09-01

The incident at Bugey 5 on 14th April 1984, which is regarded as one of the most important in recent years has alas shown again that unless dealt with by the operators in good time, failure of a rectifier supplying one of the buses may soon lead to a very serious situation, in this particular instance voltage loss on the train A 48 volt supply from the two offsite electrical sources and train A diesel generator. Operating experience feedback of the past three years reveals that although the Bugey incident is undoubtedly the most serious, it is not the only where a major alarm was not taken into consideration until fairly late by the operators, and other types of error with far from negligible consequences have occurred during repair work on buses. After a brief reminder of the role and layout of buses, statistics of all incidents of this type in recent years are described and a few cases are presented in order to give some idea of the range of situations encountered. The main measures aimed at reducing the number of incidents of this type are then presented, bearing in mind that one cannot hope to remove the possibility of this type of failure entirely. It may also be noted that the large number of such errors during the night shift or at the very beginning of the morning shift is no doubt connected with the well-known fact that operators are less vigilant at such times

EST! best practices

Science.gov (United States)

2000-10-05

This booklet presents the eighteen winners in a competition for projects that promote environmentally sustainable transportation (EST). These range from car sharing to hydrogen fueled buses to public transit promotion campaign. Each project is presen...

Addendum: Tenth International Symposium on Alcohol Fuels, The road to commercialization

Energy Technology Data Exchange (ETDEWEB)

1994-05-01

The Tenth International Symposium on ALCOHOL FUELS ``THE ROAD TO COMMERCIALIZATION`` was held at the Broadmoor Hotel, Colorado Springs, Colorado, USA November 7--10, 1993. Twenty-seven papers on the production of alcohol fuels, specifications, their use in automobiles, buses and trucks, emission control, and government policies were presented. Individual papers have been processed separately for entry into the data base.

Multistage Mechanical Transmissions with Automatic Control for Advanced Trucks and Buses

Directory of Open Access Journals (Sweden)

Blokhin Aleksandr

2017-12-01

Full Text Available The study considers the basic trends of development of modern mechanical transmissions of trucks and buses. It provides the developed various series of multispeed transmissions with automatic control and a number of transmissions from 6 to 16 for trucks and buses. The paper shows the basic parameters of the standard series of new transmissions received on the basis of innovative technical solutions. It provides the results of experimental studies of 16-speed transmissions on a special test stand and on the road as part of a truck transmission. Theoretical and experimental data on the gear change time are compared.

Real life testing of a Hybrid PEM Fuel Cell Bus

Science.gov (United States)

Folkesson, Anders; Andersson, Christian; Alvfors, Per; Alaküla, Mats; Overgaard, Lars

Fuel cells produce low quantities of local emissions, if any, and are therefore one of the most promising alternatives to internal combustion engines as the main power source in future vehicles. It is likely that urban buses will be among the first commercial applications for fuel cells in vehicles. This is due to the fact that urban buses are highly visible for the public, they contribute significantly to air pollution in urban areas, they have small limitations in weight and volume and fuelling is handled via a centralised infrastructure. Results and experiences from real life measurements of energy flows in a Scania Hybrid PEM Fuel Cell Concept Bus are presented in this paper. The tests consist of measurements during several standard duty cycles. The efficiency of the fuel cell system and of the complete vehicle are presented and discussed. The net efficiency of the fuel cell system was approximately 40% and the fuel consumption of the concept bus is between 42 and 48% lower compared to a standard Scania bus. Energy recovery by regenerative braking saves up 28% energy. Bus subsystems such as the pneumatic system for door opening, suspension and brakes, the hydraulic power steering, the 24 V grid, the water pump and the cooling fans consume approximately 7% of the energy in the fuel input or 17% of the net power output from the fuel cell system. The bus was built by a number of companies in a project partly financed by the European Commission's Joule programme. The comprehensive testing is partly financed by the Swedish programme "Den Gröna Bilen" (The Green Car). A 50 kW el fuel cell system is the power source and a high voltage battery pack works as an energy buffer and power booster. The fuel, compressed hydrogen, is stored in two high-pressure stainless steel vessels mounted on the roof of the bus. The bus has a series hybrid electric driveline with wheel hub motors with a maximum power of 100 kW. Hybrid Fuel Cell Buses have a big potential, but there are

Feasibility study on the introduction of hybrid buses; Hybrid bus donyu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this research is to design pilot projects for introducing hybrid buses into the public transportation sector. This research also covers contents regarding hybrid buses with a trolley-collector motor and a diesel engine, to identify technical and economical problems and to analyze cost beneficiation using hybrid buses. The trolley parallel hybrid system has been employed for the feasibility study. This system has abundant operation results in Europe and the USA. Its battery is small or is not necessary, and the maintenance cost is also low. As a result of the feasibility study, reduction effects of CO2 emission were found out. When the CO2 generation at the power plant is not counted, the reduction effect was estimated to be 32% compared with the CO2 emission from diesel buses. When the CO2 generation at the power plant is considered, it was estimated to be 18%. The cost beneficiation was investigated for the cases of the transportations using trolley system surrounding a medium-scale terminal among large-scale housing development, tourist resort, and stations. The annual income is estimated to be larger than the annual payment in each case. It was found that the hybrid bus is economically established. 17 refs., 48 figs., 41 tabs.

Carbon Dioxide Concentrations and Temperatures within Tour Buses under Real-Time Traffic Conditions

Science.gov (United States)

Chiu, Chun-Fu; Chen, Ming-Hung; Chang, Feng-Hsiang

2015-01-01

This study monitored the carbon dioxide (CO2) concentrations and temperatures of three 43-seat tour buses with high-passenger capacities in a course of a three-day, two-night school excursion. Results showed that both driver zones and passenger zones of the tour buses achieved maximum CO2 concentrations of more than 3000 ppm, and maximum daily average concentrations of 2510.6 and 2646.9 ppm, respectively. The findings confirmed that the CO2 concentrations detected in the tour buses exceeded the indoor air quality standard of Taiwan Environmental Protection Administration (8 hr-CO2: 1000 ppm) and the air quality guideline of Hong Kong Environmental Protection Department (1 hr-CO2: 2500 ppm for Level 1 for buses). Observations also showed that high-capacity tour bus cabins with air conditioning system operating in recirculation mode are severely lacking in air exchange rate, which may negatively impact transportation safety. Moreover, the passenger zones were able to maintain a temperature of between 20 and 25°C during travel, which effectively suppresses the dispersion of volatile organic compounds. Finally, the authors suggest that in the journey, increasing the ventilation frequency of tour bus cabin, which is very beneficial to maintain the travel safety and enhance the quality of travel. PMID:25923722

Carbon Dioxide Concentrations and Temperatures within Tour Buses under Real-Time Traffic Conditions.

Science.gov (United States)

Chiu, Chun-Fu; Chen, Ming-Hung; Chang, Feng-Hsiang

2015-01-01

This study monitored the carbon dioxide (CO2) concentrations and temperatures of three 43-seat tour buses with high-passenger capacities in a course of a three-day, two-night school excursion. Results showed that both driver zones and passenger zones of the tour buses achieved maximum CO2 concentrations of more than 3000 ppm, and maximum daily average concentrations of 2510.6 and 2646.9 ppm, respectively. The findings confirmed that the CO2 concentrations detected in the tour buses exceeded the indoor air quality standard of Taiwan Environmental Protection Administration (8 hr-CO2: 1000 ppm) and the air quality guideline of Hong Kong Environmental Protection Department (1 hr-CO2: 2500 ppm for Level 1 for buses). Observations also showed that high-capacity tour bus cabins with air conditioning system operating in recirculation mode are severely lacking in air exchange rate, which may negatively impact transportation safety. Moreover, the passenger zones were able to maintain a temperature of between 20 and 25°C during travel, which effectively suppresses the dispersion of volatile organic compounds. Finally, the authors suggest that in the journey, increasing the ventilation frequency of tour bus cabin, which is very beneficial to maintain the travel safety and enhance the quality of travel.

Methanol fuel update

International Nuclear Information System (INIS)

Colledge, R.; Spacek, J.

1992-01-01

An overview is presented of methanol fuel developments, with particular reference to infrastructure, supply and marketing. Methanol offers reduced emissions, easy handling, is cost effective, can be produced from natural gas, coal, wood, or municipal waste, is a high performance fuel, is safer than gasoline, and contributes to energy security. Methanol supply, environmental benefits, safety/health issues, economics, passenger car economics, status of passenger car technology, buses, methanol and the prosperity initiative, challenges to implementation, and the role of government and original equipment manufacturers are discussed. Governments must assist in the provision of methanol refuelling infrastructure, and in providing an encouraging regulatory atmosphere. Discriminatory and inequitable taxing methods must be addressed, and an air quality agenda must be defined to allow the alternative fuel industry to respond in a timely manner

The GREET Model Expansion for Well-to-Wheels Analysis of Heavy-Duty Vehicles

Energy Technology Data Exchange (ETDEWEB)

Cai, Hao [Argonne National Lab. (ANL), Argonne, IL (United States); Burnham, Andrew [Argonne National Lab. (ANL), Argonne, IL (United States); Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States); Hang, Wen [Argonne National Lab. (ANL), Argonne, IL (United States); Vyas, Anant [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-05-01

Heavy-duty vehicles (HDVs) account for a significant portion of the U.S. transportation sector’s fuel consumption, greenhouse gas (GHG) emissions, and air pollutant emissions. In our most recent efforts, we expanded the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREETTM) model to include life-cycle analysis of HDVs. In particular, the GREET expansion includes the fuel consumption, GHG emissions, and air pollutant emissions of a variety of conventional (i.e., diesel and/or gasoline) HDV types, including Class 8b combination long-haul freight trucks, Class 8b combination short-haul freight trucks, Class 8b dump trucks, Class 8a refuse trucks, Class 8a transit buses, Class 8a intercity buses, Class 6 school buses, Class 6 single-unit delivery trucks, Class 4 single-unit delivery trucks, and Class 2b heavy-duty pickup trucks and vans. These vehicle types were selected to represent the diversity in the U.S. HDV market, and specific weight classes and body types were chosen on the basis of their fuel consumption using the 2002 Vehicle Inventory and Use Survey (VIUS) database. VIUS was also used to estimate the fuel consumption and payload carried for most of the HDV types. In addition, fuel economy projections from the U.S. Energy Information Administration, transit databases, and the literature were examined. The U.S. Environmental Protection Agency’s latest Motor Vehicle Emission Simulator was employed to generate tailpipe air pollutant emissions of diesel and gasoline HDV types.

Quantitative characterization of the reliability of simplex buses and stars to compare their benefits in fieldbuses

International Nuclear Information System (INIS)

Barranco, Manuel; Proenza, Julián; Almeida, Luís

2015-01-01

Fieldbuses targeted to highly dependable distributed embedded systems are shifting from bus to star topologies. Surprisingly, despite the efforts into this direction, engineers lack of analyses that quantitatively characterize the system reliability achievable by buses and stars. Thus, to guide engineers in developing adequate bus and star fieldbuses, this work models, quantifies and compares the system reliability provided by simplex buses and stars for the case of the Controller Area Network (CAN). It clarifies how relevant dependability-related aspects affect reliability, refuting some intuitive ideas, and revealing some previously unknown bus and star benefits. - Highlights: • SANs models that quantify the reliability of simplex buses/stars in fieldbuses. • Models cover system relevant dependability-related features abstracted in the literature. • Results refute intuitive ideas about buses and stars and show some unexpected effects. • Models and results can guide the design of reliable simplex bus/stars fieldbuses

Development and Evaluation of an Economic-Driving Assistance Program for Transit Vehicles

Directory of Open Access Journals (Sweden)

Baoxin Han

2012-02-01

Full Text Available This paper focuses on development and evaluation of an economic-driving assistance program for transit vehicles (EDTV which can minimize energy consumption, air pollution emission of buses, and improve the level of service of transit system as well. Taking advantage of the latest advances in information and communication technologies, the EDTV system can provide bus drivers with optimal recommended bus holding times at near-side bus stops and dynamic bus speed to adapt to the real-time traffic control plan at downstream intersections. In order to address the impacts of the stochastic variation of bus dwell time, the total link between adjacent intersections is divided into three parts: upstream of bus stop part; bus stop part; and downstream of bus stop part. The methods for calculating recommended parameters, including bus holding time and bus speed in each of the three parts are proposed based on real-time bus status and signal status at downstream intersections. A VISSIM-based simulation platform was designed and used for simulating and evaluating the proposed EDTV system. Extensive experimental analyses have shown that the proposed EDTV system can improve the performance of a transit system in terms of reducing fuel consumption, air pollution emissions and level of service of the transit system.

The Business Case for Fuel Cells: Delivering Sustainable Value

Energy Technology Data Exchange (ETDEWEB)

Curtin, Sandra [Fuel Cell and Hydrogen Energy Association (FCHEA), Washington, DC (United States); Gangi, Jennifer [Fuel Cell and Hydrogen Energy Association (FCHEA), Washington, DC (United States)

2017-09-11

This report, written and compiled by Argonne National Laboratory and the Fuel Cell and Hydrogen Energy Association with support from the Fuel Cell Technologies Office, provides an overview of private sector fuel cell installations at U.S. businesses as of December 31, 2016. Over the past few decades, hundreds of thousands of fuel cells have been installed around the world, for primary or backup power, as well as in various other applications including portable and emergency backup power. Fuel cells have also been deployed in other applications such as heat and electricity for homes and apartments, material handling, passenger vehicles, buses, and remote, off-grid sites.

Considerations for the transition from fuel cell R ampersand D to manufacturing

International Nuclear Information System (INIS)

Cobb, M.A.

1992-01-01

There are a growing number of contractors within the present fuel cell community who have the potential of becoming high volume manufacturers of fuel cell power plants or components. Many are transitioning from basic research operations to manufacturing for the first time. Moving a product from the R ampersand D stage to a viable commercial product depends upon many factors. Some companies are more successful at it than others. We believe there is an underlying transition process from invention to market that is much the same for large, well established firms, as it is for start-ups. How well the process is understood and executed often determines the winners and losers in product commercialization. This paper presents a viewpoint on considerations for transitioning a new technology into commercial production and discusses some affects on organizational development

School buses, air pollution and children's health: follow-up report

International Nuclear Information System (INIS)

Perrotta, K.

2010-10-01

This document is designed to be a follow-up report to the Ontario Public Health Association (OPHA) school bus report published in 2005, and was produced through a collaboration between the Clean Air Partnership and the OPHA. The level of awareness of school bus emissions are evaluated in this report. The document also provides a review of projects handled by the federal government, programs developed by governments of other provinces and the policies followed by school boards in other provinces, to mitigate emissions and exposures related to school buses. Several recommendations were made, including the replacement of older school buses, adapt the routes considering the emissions generated and promote the use of biodiesel to reduce emissions of air pollutants and greenhouse gases. 36 refs, 8 tabs.

Network-based model for predicting the effect of fuel price on transit ridership and greenhouse gas emissions

Directory of Open Access Journals (Sweden)

Michael W. Levin

2017-12-01

Full Text Available As fuel prices increase, drivers may make travel choices to minimize not only travel time, but also fuel consumption. Consideration of fuel consumption would affect route choice and influence trip frequency and mode choice. For instance, travelers may elect to live closer to their workplace, or use public transit to avoid fuel consumption and the associated costs. To incorporate network characteristics into predictions of the effects of fuel prices, we develop a multi-class combined elastic demand, mode choice, and user equilibrium model using a generalized cost function of travel time and fuel consumption with a combined solution algorithm. The algorithm is implemented in a custom software package, and a case study application on the Austin, Texas network is presented. We evaluate the fuel-price sensitivity of key variables such as drive-alone and transit class proportions, person-miles traveled, link-level traffic flow and per capita fuel consumption and emissions. These effects are examined across a heterogeneous demand set, with multiple user-classes categorized based on their value of travel time. The highest relative transit elasticities against fuel price are observed among low value of time classes, as expected. Although total personal vehicle travel decreases, congestion increases on some roads due to the generalized cost function. Reductions in system-wide fuel consumption and greenhouse gas emissions are observed as well. The study uncovers the combined interactions among fuel prices, multi-modal choice behavior, travel performance, and resultant environmental impacts, all of which dictate the urban travel market. It also equips agencies with motivation to tailor emissions reduction and transit-ridership stimulus policies around the most responsive user classes.

Methicillin-resistant Staphylococcus aureus in public transportation vehicles (buses): another piece to the epidemiologic puzzle.

Science.gov (United States)

Lutz, Jonathan K; van Balen, Joany; Crawford, John Mac; Wilkins, John R; Lee, Jiyoung; Nava-Hoet, Rocio C; Hoet, Armando E

2014-12-01

Little is known about the occurrence and epidemiology of methicillin-resistant Staphylococcus aureus (MRSA) in public transportation in the United States. This research sought to determine the background prevalence and phenotypic and genotypic characteristics of MRSA strains circulating on buses from a large, metropolitan transportation agency. Electrostatic wipes were used to collect 237 surface samples from 40 buses randomly selected from July-October 2010. Six samples were collected from each bus immediately postservice and before any cleaning and disinfection. Positive isolates were analyzed for antibiotic resistance, staphylococcal cassette chromosome mec (SCCmec) type, and pulsed-field gel electrophoresis; and potential epidemiologic factors were examined. Of the buses, 68% (27/40) were contaminated with S aureus, and 63% (25/40) were contaminated with MRSA. Seats and seat rails were the surfaces most frequently contaminated, followed by the back door and stanchions. Most (62.9%) of the MRSA isolates were classified as community-associated MRSA clones (SCCmec type IV), and 22.9% were health care-associated MRSA clones (SCCmec type II). Of the MRSA strains, 65% (5/20) were multidrug resistant. MRSA was frequently isolated from commonly touched surfaces in buses serving both hospital and community routes. Phenotypic and genotypic analysis demonstrated that buses may be effective mixing vessels for MRSA strains of both community and health care-associated origin. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

The impact of transit signal priority: case study in Dubai, UAE

Directory of Open Access Journals (Sweden)

Al Khateeb Hadeel

2017-01-01

Full Text Available Abdulfatah & Alkhateeb proposes on this paper one of the Intelligent Transportation Systems- ITS, the Transit Signal Priority- TSP, which involves real time tracking. The United States is considered one of the lead countries in implementing this strategy since decades ago. Europe and Germany have also implemented TSP quite extensively to improve rider-ship and buses efficiency. TSP is a strategy that supports the transit system through easing the movement of the service. The operational technique used for TSP is controlling the signal system at the intersections. A detector system must be integrated in the implementation stage. It will detect the preference of public buses among the other vehicles in the traffic queue. Determining of optimal detector location for the TSP with queued lanes is the main feature. It must be studied and decided on before starting different signalization proposals for the intersection. Controlling traffic signal in favor of the public bus system will improve reliability and efficiency for buses. Meanwhile, the extreme impact of the TSP on general traffic as well as on public buses became the basis for many recent studies and thesis tested by many authors. The scope of the project as addressed in this paper is to report the delivered results of different scenarios tested, and then compare these proposed scenarios to select the best signal consideration, which has a potential impact on bus and traffic performance. After applying TSP, the results show that the impact of actuating traffic signals in Al Mussallah / Al Maktoum corridor after extending green time for bus approach (15 sec through minimum reduction on average travel time for busses by 7.04%and tremendous increase in travel time for cars by 38.68%. A reduction in cars Avg. Speed by 28.04% in comparison to 35.52% buses Avg. Speed. On the other hand, a reduction in buses delay received by 14.11% and a decrease in Avg. Stopped delay per bus of about 18.56%, while

Transitioning nuclear fuel cycles with uncertain fast reactor costs

Energy Technology Data Exchange (ETDEWEB)

Phathanapirom, U.B., E-mail: bphathanapirom@utexas.edu; Schneider, E.A.

2016-06-15

This paper applies a novel decision making methodology to a case study involving choices leading to the transition from the current once-through light water reactor fuel cycle to one relying on continuous recycle of plutonium and minor actinides in fast reactors in the face of uncertain fast reactor capital costs. Unique to this work is a multi-stage treatment of a range of plausible trajectories for the evolution of fast reactor capital costs over time, characterized by first-of-a-kind penalties as well as time- and unit-based learning. The methodology explicitly incorporates uncertainties in key parameters into the decision-making process by constructing a stochastic model and embedding uncertainties as bifurcations in the decision tree. “Hedging” strategies are found by applying a choice criterion to select courses of action which mitigate “regrets”. These regrets are calculated by evaluating the performance of all possible transition strategies for every feasible outcome of the uncertain parameter. The hedging strategies are those that preserve the most flexibility for adjusting the fuel cycle strategy in response to new information as uncertainties are resolved.

Transitioning nuclear fuel cycles with uncertain fast reactor costs

International Nuclear Information System (INIS)

Phathanapirom, U.B.; Schneider, E.A.

2016-01-01

This paper applies a novel decision making methodology to a case study involving choices leading to the transition from the current once-through light water reactor fuel cycle to one relying on continuous recycle of plutonium and minor actinides in fast reactors in the face of uncertain fast reactor capital costs. Unique to this work is a multi-stage treatment of a range of plausible trajectories for the evolution of fast reactor capital costs over time, characterized by first-of-a-kind penalties as well as time- and unit-based learning. The methodology explicitly incorporates uncertainties in key parameters into the decision-making process by constructing a stochastic model and embedding uncertainties as bifurcations in the decision tree. “Hedging” strategies are found by applying a choice criterion to select courses of action which mitigate “regrets”. These regrets are calculated by evaluating the performance of all possible transition strategies for every feasible outcome of the uncertain parameter. The hedging strategies are those that preserve the most flexibility for adjusting the fuel cycle strategy in response to new information as uncertainties are resolved.

Concentrations and risk assessment of selected monoaromatic hydrocarbons in buses and bus stations of Hangzhou, China.

Science.gov (United States)

Li, Shuang; Chen, Shuguang; Zhu, Lizhong; Chen, Xiasheng; Yao, Chaoying; Shen, Xueyou

2009-03-01

Air pollution surveys of ten selected monoaromatic hydrocarbons (MAHCs) were conducted in buses and bus stations in Hangzhou, China. The mean concentrations of MAHCs in the air of buses and bus stations were 95.9 and 36.5 microg/m(3), respectively, of which toluene was the highest in all the sampling sites. Mean concentrations of all MAHCs in buses were statistically higher than those nearby bus stations (pbus drivers were 1.11x10(-5) and 4.00x10(-5), respectively, which were way above the limit set by USEPA. The health risk caused by MAHCs in bus microenvironment should be cautioned.

Efficiency evaluation of gas fuelled and electric driven buses in the public transport sector

Energy Technology Data Exchange (ETDEWEB)

Aigner, Tobias Alexander

2013-07-01

The following report evaluates the efficiency of gas fuelled and electric driven buses in the public transport sector on a theoretical basis. The results indicate that the combination of CHP power plants and electric driven buses reach an overall efficiency of about 51% throughout the production chain (Well-to-Wheel), including heat distribution losses. The overall Well-to-Wheel efficiency for conventional gas turbines without heat recovery decreases to around 28%. For gas fuelled buses the Well-to-Wheel efficiency is about 30%. The Co2-emissions are evaluated based on the example of a #Left Double Quotation Mark#Volvo B10L CNG#Right Double Quotation Mark# gas bus and the electric driven #Left Double Quotation Mark#Eurabus 600#Right Double Quotation Mark#. The low energy consumption of the electric driven bus results in Co2-emissions of only 181.4 g Co2/km (Grid-to-Wheel). Depending on the utilised power plant technology the overall Co2-emissions (Well-to-Wheel) amount to 307.5 g Co2/km for a CHP power plant and 553.5 g Co2/km for a conventional gas turbine. On the other hand, gas fuelled buses emit about 1.25 kg Co2/km (Tank-to-Wheel), which is eightfold the emissions of an electrical bus. The Well-to-Tank emissions further increase to about 1.32 kg Co2/km. The emission calculation is based on real gas consumption data from a Norwegian public transport utility. The results indicate that the combination of CHP plants and electrical buses provide a much higher efficiency while reducing Co2-emissions. (author)

Are We There Yet? Alternative Fuels for School Buses

Science.gov (United States)

Lea, Dennis; Carter, Deborah

2009-01-01

America's annual oil consumption continues to increase and is projected to continue the upward spiral into the foreseeable future. Alternative-fuel options are available that are not only cheaper in some cases on an energy-equivalent basis but are also more environmentally friendly. Education leaders need to be concerned with both these facts.…

Advances in simulating non-congruent phase transitions of hyperstoichiometric uranium dioxide fuel

International Nuclear Information System (INIS)

Welland, M.J.; Thompson, W.T.; Lewis, B.J.

2007-01-01

A model is being developed to simulate UO 2 at very high temperatures incorporating the effects of non-congruent phase transitions. In particular, the melting transformation and the possible 'Λ-transition' is being investigated to help support the design and analysis of experimental work being conducted as part of nuclear safety research. This work includes the interpretation of the behaviour of operating CANDU fuel under upset conditions, where centerline melting may potentially occur (particularly if the fuel is oxidized). The model presented here numerically solves a system of coupled nonlinear differential equations as derived from fundamental principles. The results of the model present here compare well against laser flash experiments in recently published literature. (author)

The KFB Program on Biobased Fuels for Vehicles

International Nuclear Information System (INIS)

1996-12-01

KFB supports research and demonstration projects for bio-based transport fuels, alcohols and biogas. The program started in 1991 and will continue through 1997. The program focuses on heavy vehicles, e.g. buses for public transportation. Projects and intermediate results are described in the brochure. Information is also available at the KFB homepage. //www.kfb.se

Detection of maximum loadability limits and weak buses using Chaotic PSO considering security constraints

International Nuclear Information System (INIS)

Acharjee, P.; Mallick, S.; Thakur, S.S.; Ghoshal, S.P.

2011-01-01

Highlights: → The unique cost function is derived considering practical Security Constraints. → New innovative formulae of PSO parameters are developed for better performance. → The inclusion and implementation of chaos in PSO technique is original and unique. → Weak buses are identified where FACTS devices can be implemented. → The CPSO technique gives the best performance for all the IEEE standard test systems. - Abstract: In the current research chaotic search is used with the optimization technique for solving non-linear complicated power system problems because Chaos can overcome the local optima problem of optimization technique. Power system problem, more specifically voltage stability, is one of the practical examples of non-linear, complex, convex problems. Smart grid, restructured energy system and socio-economic development fetch various uncertain events in power systems and the level of uncertainty increases to a great extent day by day. In this context, analysis of voltage stability is essential. The efficient method to assess the voltage stability is maximum loadability limit (MLL). MLL problem is formulated as a maximization problem considering practical security constraints (SCs). Detection of weak buses is also important for the analysis of power system stability. Both MLL and weak buses are identified by PSO methods and FACTS devices can be applied to the detected weak buses for the improvement of stability. Three particle swarm optimization (PSO) techniques namely General PSO (GPSO), Adaptive PSO (APSO) and Chaotic PSO (CPSO) are presented for the comparative study with obtaining MLL and weak buses under different SCs. In APSO method, PSO-parameters are made adaptive with the problem and chaos is incorporated in CPSO method to obtain reliable convergence and better performances. All three methods are applied on standard IEEE 14 bus, 30 bus, 57 bus and 118 bus test systems to show their comparative computing effectiveness and

Analysis of transition to fuel cycle system with continuous recycling in fast and thermal reactors - 5060

International Nuclear Information System (INIS)

Passereini, S.; Feng, B.; Fei, T.; Kim, T.K.; Taiwo, T.A.; Brown, N.R.; Cuadra, A.

2015-01-01

A recent Evaluation and Screening study of nuclear fuel cycle options identified a few groups of options as most promising. One of these most promising Evaluation Groups (EGs) is characterized by the continuous recycling of uranium (U) and transuranics (TRU) with natural uranium feed in both fast and thermal critical reactors. This evaluation group, designated as EG30, is represented by an example fuel cycle option that employs a two-technology, two-stage fuel cycle system. The first stage involves the continuous recycling of co-extracted U/TRU in Sodium-cooled Fast Reactors (SFRs) with metallic fuel and breeding ratio greater than 1. The second stage involves the use of the surplus TRU in Mixed Oxide (MOX) fuel in Pressurized Water Reactors that are MOX-capable (MOX-PWRs). This paper presents and discusses preliminary fuel cycle analysis results from the fuel cycle codes VISION and DYMOND for the transition to this fuel cycle option from the current once-through cycle in the United States (U.S.) that consists of Light Water Reactors (LWRs) that only use conventional UO 2 fuel. The analyses in this paper are applicable for a constant 100 GWe capacity, roughly the size of the U.S. nuclear fleet. Two main strategies for the transition to EG30 were analyzed: 1) deploying both SFRs and MOX-PWRs in parallel or 2) deploying them in series with the SFR fleet first. With an estimated retirement schedule for the existing LWRs, an assumed reactor lifetime of 60 years, and no growth, the nuclear system fully transitions to the new fuel cycle within 100 years for both strategies without SFR fuel shortages. Compared to the once-through cycle, transition to the SFR/MOX-PWR fleet with continuous recycle was shown to offer significant reductions in uranium consumption and waste disposal requirements. In addition, these initial calculations revealed a few notable modeling and strategy questions regarding how recycled resources are allocated, reactors that can switch between

Predicting self-pollution inside school buses using a CFD and multi-zone coupled model

Science.gov (United States)

Li, Fei; Lee, Eon S.; Liu, Junjie; Zhu, Yifang

2015-04-01

The in-cabin environment of a school bus is important for children's health. The pollutants from a bus's own exhaust contribute to children's overall exposure to air pollutants inside the school bus cabin. In this study, we adapted a coupled model originally developed for indoor environment to determine the relative contribution of the bus own exhaust to the in-cabin pollutant concentrations. The coupled model uses CFD (computational fluent dynamics) model to simulate outside concentration and CONTAM (a multi-zone model) for inside the school bus. The model was validated with experimental data in the literature. Using the validated model, we analyzed the effects of vehicle speed and tailpipe location on self-pollution inside the bus cabin. We confirmed that the pollution released from the tailpipe can penetrate into the bus cabin through gaps in the back emergency door. We found the pollution concentration inside school buses was the highest when buses were driven at a medium speed. In addition, locating the tailpipe on the side, behind the rear axle resulted in less self-pollution since there is less time for the suction effect to take place. The developed theoretical framework can be generalized to study other types of buses. These findings can be used in developing policy recommendations for reducing human exposure to air pollution inside buses.

The Aerodynamics of Heavy Vehicles III : Trucks, Buses and Trains

CERN Document Server

Orellano, Alexander

2016-01-01

This volume contains papers presented at the International conference “The Aerodynamics of Heavy Vehicles III: Trucks, Buses and Trains” held in Potsdam, Germany, September 12-17, 2010 by Engineering Conferences International (ECI). Leading scientists and engineers from industry, universities and research laboratories, including truck and high-speed train manufacturers and operators were brought together to discuss computer simulation and experimental techniques to be applied for the design of more efficient trucks, buses and high-speed trains in the future.   This conference was the third in the series after Monterey-Pacific Groove in 2002 and Lake Tahoe in 2007.  The presentations address different aspects of train aerodynamics (cross wind effects, underbody flow, tunnel aerodynamics and aeroacoustics, experimental techniques), truck aerodynamics (drag reduction, flow control, experimental and computational techniques) as well as computational fluid dynamics and bluff body, wake and jet flows.

Analysis of temperature and pressure changes in liquefied natural gas (LNG) cryogenic tanks

Science.gov (United States)

Chen, Q.-S.; Wegrzyn, J.; Prasad, V.

2004-10-01

Liquefied natural gas (LNG) is being developed as a transportation fuel for heavy vehicles such as trucks and transit buses, to lessen the dependency on oil and to reduce greenhouse gas emissions. The LNG stations are properly designed to prevent the venting of natural gas (NG) from LNG tanks, which can cause evaporative greenhouse gas emissions and result in fluctuations of fuel flow and changes of fuel composition. Boil-off is caused by the heat added into the LNG fuel during the storage and fueling. Heat can leak into the LNG fuel through the shell of tank during the storage and through hoses and dispensers during the fueling. Gas from tanks onboard vehicles, when returned to LNG tanks, can add additional heat into the LNG fuel. A thermodynamic and heat transfer model has been developed to analyze different mechanisms of heat leak into the LNG fuel. The evolving of properties and compositions of LNG fuel inside LNG tanks is simulated. The effect of a number of buses fueled each day on the possible total fuel loss rate has been analyzed. It is found that by increasing the number of buses, fueled each day, the total fuel loss rate can be reduced significantly. It is proposed that an electric generator be used to consume the boil-off gas or a liquefier be used to re-liquefy the boil-off gas to reduce the tank pressure and eliminate fuel losses. These approaches can prevent boil-off of natural gas emissions, and reduce the costs of LNG as transportation fuel.

Evaluation of the use of bioethanol fuelled buses based on ambient air pollution screening and on-road measurements.

Science.gov (United States)

López-Aparicio, S; Hak, C

2013-05-01

Mitigation measures to reduce greenhouse gas emissions may have adverse effects on urban air quality and human exposure to harmful pollutants. The use of bioethanol fuelled vehicles is increasing worldwide and may create new undesired pollution effects. Different measurement campaigns were performed in a pilot study to contribute to the understanding of the consequences associated with the use of bioethanol blended fuel (E95) on a series of pollutants. Ambient screening measurements of NO2, O3, acetic acid, formaldehyde and acetaldehyde were performed at different urban locations, exposed and not exposed to the circulation of bioethanol buses. In addition, volatile organic compounds were measured at the exhaust pipe of a bioethanol fuelled bus, both under idling conditions (carbonyls; DNPH cartridge) and under on-road driving conditions applying online monitoring (PTR-TOF). Higher ambient acetaldehyde values were measured at locations exposed to bioethanol fuelled buses than at locations not exposed, and very high acetaldehyde and acetic acid values were measured from the exhaust pipe during driving conditions (acetaldehyde>150 ppm; acetic acid ≈ 20-30 ppm) and modelled at close distance to the bioethanol bus. Human exposure to high concentration of acetaldehyde is expected, and it may involve a significantly increased chance in developing cancer. The high concentration of acetic acid will involve odour annoyance and significant material degradation or corrosion. Copyright © 2013 Elsevier B.V. All rights reserved.

Impact of Spanish electricity mix, over the period 2008–2030, on the Life Cycle energy consumption and GHG emissions of Electric, Hybrid Diesel-Electric, Fuel Cell Hybrid and Diesel Bus of the Madrid Transportation System

International Nuclear Information System (INIS)

García Sánchez, Juan Antonio; López Martínez, José María; Lumbreras Martín, Julio; Flores Holgado, María Nuria; Aguilar Morales, Hansel

2013-01-01

Highlights: • We assess the performance of 4 buses that run on different alternative fuel types and technologies. • The buses assessed are Fuel Cell-Hybrid Bus, Hybrid Diesel-Electric Bus, Battery Electric Bus, and a Diesel Bus. • We examine the environmental impact caused by the Life Cycle of each vehicle technology, fossil fuel and energy carrier. • Life Cycle of Battery Electric Bus shows that it has a big potential of improvement in terms of environmental impact. - Abstract: In spite of the advanced research in automotive technology, and the improvement of fuels, the road transport sector continues to be an environmental concern, since the increase in transport demand is offsetting the effects of these technological improvements. Therefore, this poses the following question: what combination of technology and fuel is more efficient in terms of energy consumption and green house gas (GHG) emissions? To fully address this question it is necessary to carry out a Life Cycle Assessment (LCA). This paper presents a global LCA of 4 buses that run on the following fuel types and technologies: (1) Fuel Cell- Hybrid Bus, (2) Hybrid Diesel-Electric Bus (series configuration), (3) Battery Electric Bus and (4) Combustion Ignition Engine Bus. The impact categories assessed are: primary energy consumption, fossil energy and GHG emissions. Among the principal results, we can conclude that the Global LCA of buses (3) and (1) (which are the more sensitive pathways to the electricity mix variation) have for the 2008–2030 period a room for improvement of 25.62% and 28.16% in terms of efficiency of fossil energy consumption and a potential GHG emission reduction of 28.70% and 30.88% respectively

Core-state models for fuel management of equilibrium and transition cycles in pressurized water reactors

International Nuclear Information System (INIS)

Aragones, J.M.; Martinez-Val, J.M.; Corella, M.R.

1977-01-01

Fuel management requires that mass, energy, and reactivity balance be satisfied in each reload cycle. Procedures for selection of alternatives, core-state models, and fuel cost calculations have been developed for both equilibrium and transition cycles. Effective cycle lengths and fuel cycle variables--namely, reload batch size, schedule of incore residence for the fuel, feed enrichments, energy sharing cycle by cycle, and discharge burnup and isotopics--are the variables being considered for fuel management planning with a given energy generation plan, fuel design, recycling strategy, and financial assumptions

Hydrogen fuel injection - the bridge to fuel cells

International Nuclear Information System (INIS)

Gilchrist, J.S.

2004-01-01

'Full text:' For over a century, industry has embraced a wide variety of applications for hydrogen. Since the mid-1970's, the focus of the bulk of hydrogen research has been in the area of fuel cells. Unfortunately, there is limited awareness of more immediate applications for hydrogen as a catalyst designed to improve the performance of existing hydro-carbon fuelled internal combustion engines. Canadian Hydrogen Energy Company manufactures a patented Hydrogen Fuel Injection System (HFI) that produces hydrogen and oxygen from distilled water and injects them, in measured amounts, into the air intake system on any heavy-duty diesel or gasoline application including trucks, buses, stationary generators, etc. In use on over 30 fleets, research is supported by over 40 million miles of field data. The hydrogen acts as a catalyst to promote more complete combustion, with remarkable results. Dramatically reduce emissions, particularly Carbon Monoxide and Particulate Matter. Increase horsepower and torque. Improved fuel efficiency (a minimum 10% improvement is guaranteed). Reduced oil degradation The HFI system offers the first large-scale application of the use of hydrogen and an excellent bridge to the fuel-cell technologies of the future. (author)

Transition of Natural Frequencies of a Fuel Rod during Its Lifetime

International Nuclear Information System (INIS)

Kim, Hyeong Koo; Lee, Kyou Seok; Kim, Jeong Ha; Jeon, Sang Yoon

2009-01-01

The natural frequencies of a Pressurized Water Reactor (PWR) fuel rod are dependent on the geometrical and mechanical properties of fuel rod itself and its supporting conditions provided by spacer grids. By the way, these environmental parameters suffer remarkable change due to the plant operating conditions such as burnup, temperature, system pressure, and so on. It is inevitable, therefore, to be changed the natural frequencies of the fuel rod during its lifetime. In this paper, the transition of natural frequencies of the fuel rod for OPR1000 plants has been investigated considering fuel conditions associated with fuel life time. Basically for this investigation, three analysis models have been proposed representing beginning-of life (BOL) condition, middle-of-life (MOL) condition and end-of-life (EOL) condition including spacer grid supporting conditions. With these models, several modal analyses have been performed and the results have been compared with those of the test which has been carried out for verification of the analysis model. With these analyses and test, the changing vibration behavior of the PLUS7 fuel rod for OPR1000 during its life time has been discussed

Bus transit operational efficiency resulting from passenger boardings at park-and-ride facilities.

Science.gov (United States)

2016-08-01

In order to save time and money by not driving to an ultimate destination, some urban commuters drive themselves a few miles to specially designated parking lots built for transit customers and located where trains or buses stop. The focus of this pa...

Evaluation of In-Core Fuel Management for the Transition Cores of RSG-GAS Reactor to Full-Silicide Core

International Nuclear Information System (INIS)

S, Tukiran; MS, Tagor; P, Surian

2003-01-01

The core conversion of RSG-GAS reactor from oxide to silicide core with meat density of 2.96 gU/cc has been done. The core-of RSG-GAS reactor has been operated full core of silicide fuels which is started with the mixed core of oxide-silicide start from core 36. Based on previous work, the calculated core parameter for the cores were obtained and it is needed 9 transition cores (core 36 - 44) to achieve a full-silicide core (core 45). The objective of this work is to acquire the effect of the increment of the number of silicide fuel on the core parameters. Conversion core was achieved by transition cores mixed oxide-silicide fuels. Each transition core is calculated and measured core parameter such as, excess reactivity and shutdown margin. Calculation done by Batan-EQUIL-2D code and measurement of the core parameters was carried out using the method of compensation of couple control rods. The results of calculation and experiment shows that the excess reactivity trends lower with the increment of the number of silicide fuel in the core. However, the shutdown margin is not change with the increment of the number of silicide fuel. Therefore, the transition cores can be operated safely to a full-silicide core

New portal axle for low-floor electric-powered city buses; Neue Portalachse fuer Niederflur-Stadtbusse mit E-Antrieb

Energy Technology Data Exchange (ETDEWEB)

Mueller, Axel Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany); Solka, Ulrich [ZF Passau GmbH, Passau (Germany)

2010-07-01

Serial hybrid systems do have due to the very distinctive intra-urban driving cycles and the low average speeds in city bus applications very good technical characteristics regarding reduction of emissions and fuel consumption. Hence, in comparison to passenger car applications this technical solution has found a wide spreading in the field of city busses. This contribution describes the essential characteristics of the new-developed, electrically driven low floor portal axle AVE 130 for city buses from ZF. Beside the main features of the mechanical constructive assembly, the qualities of the electric drive with the features of the specifically developed asynchronous electrical machines are shown. Another main focus forms the description of the system characteristics of a city bus, which is equipped with a serial hybrid system and the new electrical portal axle. On this occasion, traction performances, aggregate arrangement, weight balances and the interaction of the components in the electrical driveline are discussed. Finally the results of simulation calculations regarding the fuel saving potential in such systems round the paper out. (orig.)

School buses, air pollution and children's health: follow-up report

Energy Technology Data Exchange (ETDEWEB)

Perrotta, K. [Clean Air Partnership, Toronto, ON (Canada)], email: Kperrotta@cleanairpartnership.org

2010-10-15

This document is designed to be a follow-up report to the Ontario Public Health Association (OPHA) school bus report published in 2005, and was produced through a collaboration between the Clean Air Partnership and the OPHA. The level of awareness of school bus emissions are evaluated in this report. The document also provides a review of projects handled by the federal government, programs developed by governments of other provinces and the policies followed by school boards in other provinces, to mitigate emissions and exposures related to school buses. Several recommendations were made, including the replacement of older school buses, adapt the routes considering the emissions generated and promote the use of biodiesel to reduce emissions of air pollutants and greenhouse gases. 36 refs, 8 tabs.

Ultrafine particle emissions by in-use diesel buses of various generations at low-load regimes

Science.gov (United States)

Tartakovsky, L.; Baibikov, V.; Comte, P.; Czerwinski, J.; Mayer, A.; Veinblat, M.; Zimmerli, Y.

2015-04-01

Ultrafine particles (UFP) are major contributors to air pollution due to their easy gas-like penetration into the human organism, causing adverse health effects. This study analyzes UFP emissions by buses of different technologies (from Euro II till Euro V EEV - Enhanced Environmentally-friendly Vehicle) at low-load regimes. Additionally, the emission-reduction potential of retrofitting with a diesel particle filter (DPF) is demonstrated. A comparison of the measured, engine-out, particle number concentrations (PNC) for buses of different technological generations shows that no substantial reduction of engine-out emissions at low-load operating modes is observed for newer bus generations. Retrofitting the in-use urban and interurban buses of Euro II till Euro IV technologies by the VERT-certified DPF confirmed its high efficiency in reduction of UFP emissions. Particle-count filtration efficiency values of the retrofit DPF were found to be extremely high - greater than 99.8%, similar to that of the OEM filter in the Euro V bus.

PEM fuel cells thermal and water management fundamentals

CERN Document Server

Wang, Yun; Cho, Sung Chan

2014-01-01

Polymer Electrolyte Membrane (PEM) fuel cells convert chemical energy in hydrogen into electrical energy with water as the only by-product. Thus, PEM fuel cells hold great promise to reduce both pollutant emissions and dependency on fossil fuels, especially for transportation-passenger cars, utility vehicles, and buses-and small-scale stationary and portable power generators. But one of the greatest challenges to realizing the high efficiency and zero emissions potential of PEM fuel cells technology is heat and water management. This book provides an introduction to the essential concepts for effective thermal and water management in PEM fuel cells and an assessment on the current status of fundamental research in this field. The book offers you: An overview of current energy and environmental challenges and their imperatives for the development of renewable energy resources, including discussion of the role of PEM fuel cells in addressing these issues; Reviews of basic principles pertaining to PEM fuel cel...

Luxurious Buses As Means Of Night Journey In Nigeria: Challenges ...

African Journals Online (AJOL)

transfer to discourage robbery cases on our roads. Passengers should also keep their traveling plans secret as much as possible as a way of fostering safety. Keywords: night journey, armed robbers, luxurious buses and police escorts. Ethiopian Journal of Environmental Studies and Management Vol. 1 (3) 2008: pp. 52-62.

Consumption-efficient regulation and switching concepts for air conditioners in buses; Verbrauchseffiziente Regelungs- und Verschaltungskonzepte fuer Omnibusklimaanlagen

Energy Technology Data Exchange (ETDEWEB)

Kaiser, Christian; Tegethoff, Wilhelm [TLK-Thermo GmbH, Braunschweig (Germany); Koehler, Juergen [TU Braunschweig (Germany). Inst. fuer Thermodynamik; Sonnekalb, Michael [Konvekta AG, Schwalmstadt (Germany)

2012-07-01

The reduction of the fuel consumption and the related reduction of CO{sub 2} emissions is one of the most important requirements in the current development of vehicles. This includes the development of fuel-efficient drive systems and the optimization of the so-called auxiliary users such as the air conditioner. The majority of the buses used today have an air conditioner in order to meet the increased demand of passengers for comfort. Since the operation of the air conditioner results in a significant increase in fuel consumption and thus in enhanced emissions of CO{sub 2}, an essential task of the development engineer is to minimize this additional consumption. In order to identify possible optimization potentials, a bus simulation model was developed which investigates not only exclusively compression refrigeration systems, but also is in communication with their relevant systems: heating circuit with engine cooling circuit, vehicle interior, on-board electrical system and vehicle longitudinal dynamics with the drive train. In the contribution under consideration, potentials of energy conservation should be identified that can be achieved due to the use of improved control and switching concepts. For this purpose, both the conventional R-744 (CO{sub 2}) bus air conditioning systems as well as alternative systems such as an ejector cycle were studied by means of a total vehicle simulation of the bus and compared.

Simulation on the consumption-oriented evaluation of ventilation concepts for buses; Simulation zur verbrauchsorientierten Bewertung von Omnibus-Klimatisierungskonzepten

Energy Technology Data Exchange (ETDEWEB)

Kaiser, Christian; Foersterling, Sven; Strupp, Christian; Lemke, Nicholas [TLK Thermo GmbH, Braunschweig (Germany); Sonnekalb, Michael [Konvekta AG, Schwalmstadt (Germany); Koehler, Juergen [Technische Univ. Braunschweig (Germany)

2012-11-01

This paper presents different air conditioning system and climate control concepts for buses. These concepts are investigated based on a complete vehicle simulation in order to perform a close-to-reality assessment. The effects of various control strategies are examined in a comparative approach using boundary conditions which are based on on-the-road-relevant test cycles and climatic conditions. The focus of this study is the evaluation of the total energy consumption. Moreover, an analysis of air conditioning systems with conventional and natural refrigerants is presented (R-134a and R-744). Based on simulation results, a high fuel-saving concept is developed and tested in a virtual test drive, in order to present a specific method of control strategy evaluation with transient boundary and environmental conditions. (orig.)

Effect of Variation of Speed Limits on Intercity Bus Fuel Consumption, Coach and Driver Utilization, and Corporate Profitability

Science.gov (United States)

1975-11-01

The effect of speed limit and passenger load on fuel consumption was determined using actual intercity buses with simulated passenger loads over different types of terrain. In addition to road tests, laboratory type measurements were made on four int...

Economic potential of fuel recycling options: A lifecycle cost analysis of future nuclear system transition in China

International Nuclear Information System (INIS)

Gao, Ruxing; Choi, Sungyeol; Il Ko, Won; Kim, Sungki

2017-01-01

In today's profit-driven market, how best to pursue advanced nuclear fuel cycle technologies while maintaining the cost competitiveness of nuclear electricity is of crucial importance to determine the implementation of spent fuel reprocessing and recycling in China. In this study, a comprehensive techno-economic analysis is undertaken to evaluate the economic feasibility of ongoing national projects and the technical compatibility with China's future fuel cycle transition. We investigated the dynamic impacts of technical and economic uncertainties in the lifecycle of a nuclear system. The electricity generation costs associated with four potential fuel cycle transition scenarios were simulated by probabilistic and deterministic approaches and then compared in detail. The results showed that the total cost of a once-through system is lowest compared those of other advanced systems involving reprocessing and recycling. However, thanks to the consequential uncertainties caused by the further progress toward technology maturity, the economic potential of fuel recycling options was proven through a probabilistic uncertainty analysis. Furthermore, it is recommended that a compulsory executive of closed fuel cycle policy would pose some investment risk in the near term, though the execution of a series of R&D initiatives with a flexible roadmap would be valuable in the long run. - Highlights: • Real-time economic performance of the four scenarios of China's nuclear fuel cycle system transition until 2100. • Systematic assessments of techno-economic feasibility for ongoing national reprocessing projects. • Investigation the cost impact on nuclear electricity generation caused by uncertainties through probabilistic analysis. • Recommendation for sustainable implementation of fuel cycle R&D initiative ingrate with flexible roadmap in the long run.

Development and Evaluation of an Economic-Driving Assistance Program for Transit Vehicles

OpenAIRE

Baoxin Han; Wanjing Ma; Hanzhou Xie

2012-01-01

This paper focuses on development and evaluation of an economic-driving assistance program for transit vehicles (EDTV) which can minimize energy consumption, air pollution emission of buses, and improve the level of service of transit system as well. Taking advantage of the latest advances in information and communication technologies, the EDTV system can provide bus drivers with optimal recommended bus holding times at near-side bus stops and dynamic bus speed to adapt to the real-time traff...

Driving cycle characterization and generation, for design and control of fuel cell buses

NARCIS (Netherlands)

Tazelaar, E.; Bruinsma, J.; Veenhuizen, P.A.; Bosch, van den P.P.J.

2009-01-01

Optimization routines for battery, supercap and fuel cell stack in a fuel cell based propulsion system face two problems: the tendency to cycle beating and the necessity to maintain identical amounts of stored energy in battery and supercap at the start and end of the driving cycle used in the

Hydrogen Village : creating hydrogen and fuel cell communities

International Nuclear Information System (INIS)

Smith, G.R.

2009-01-01

The Hydrogen Village (H2V) is a collaborative public-private partnership administered through Hydrogen and Fuel Cells Canada and funded by the Governments of Canada and Ontario. This end user-driven, market development program accelerates the commercialization of hydrogen and fuel cell (FC) technologies throughout the Greater Toronto Area (GTA). The program targets 3 specific aspects of market development, notably deployment of near market technologies in community based stationary and mobile applications; development of a coordinated hydrogen delivery and equipment service infrastructure; and societal factors involving corporate policy and public education. This presentation focused on lessons learned through outreach programs and the deployment of solid oxide fuel cell (SOFC) heat and power generation; indoor and outdoor fuel cell back up power systems; fuel cell-powered forklifts, delivery vehicles, and utility vehicles; hydrogen internal combustion engine powered shuttle buses, sedans, parade float; hydrogen production/refueling stations in the downtown core; and temporary fuel cell power systems

Fast reactor core design studies to cope with TRU fuel composition changes in the LWR-to-FBR transition period

International Nuclear Information System (INIS)

Kawashima, Katsuyuki; Maruyama, Shuhei; Ohki, Shigeo; Mizuno, Tomoyasu

2009-01-01

As part of the Fast Reactor Cycle Technology Development Project (FaCT Project), sodium-cooled fast reactor core design efforts have been made to cope with the TRU fuel composition changes expected during LWR-to-FBR transition period, in which a various kind of TRU fuel compositions are available depending on the characteristics of the LWR spent fuels and a way of recycling them. A 750 MWe mixed-oxide fuel core is firstly defined as a FaCT medium-size reference core and its neutronics characteristics are determined. The core is a high internal conversion type and has an average burnup of 150 GWD/T. The reference TRU fuel composition is assumed to come from the FBR equilibrium state. Compared to the LWR-to-FBR transition period, the TRU fuels in the FBR equilibrium period are multi-recycled through fast reactors and have a different composition. An available TRU fuel composition is determined by fast reactor spent fuel multi-recycling scenarios. Then the FaCT core corresponding to the TRU fuel with different compositions is set according to the TRU fuel composition changes in LWR-to-FBR transition period, and the key core neutronics characteristics are assessed. It is shown that among the core neutronics characteristics, the burnup reactivity and the safety parameters such as sodium void reactivity and Doppler coefficient are significantly influenced by the TRU fuel composition changes. As a result, a general characteristic in the FaCT core design to cope with TRU fuel composition changes is grasped and the design envelopes are identified in terms of the burnup reactivity and the safety parameters. (author)

Preliminary study on field buses for the control system of the high voltage of the ATLAS hadronic calorimeter

International Nuclear Information System (INIS)

Drevet, F.; Chadelas, R.; Montarou, G.

1996-01-01

We present here after a preliminary study on field buses for the control system of the high voltage of the photomultipliers of the TILECAL calorimeter. After some generalities, different commercial buses are reviewed (CAN, ARCET, WorldFIP, Profibus and LonWorks). The Profibus and LonWorks solution are more extensively studies as a possible solution for the high voltage system of the TILE hadronic calorimeter. (authors)

Improved Accelerated Stress Tests Based on Fuel Cell Vehicle Data

Energy Technology Data Exchange (ETDEWEB)

Patterson, Timothy [Research Engineer; Motupally, Sathya [Research Engineer

2012-06-01

UTC will led a top-tier team of industry and national laboratory participants to update and improve DOE’s Accelerated Stress Tests (AST’s) for hydrogen fuel cells. This in-depth investigation will focused on critical fuel cell components (e.g. membrane electrode assemblies - MEA) whose durability represented barriers for widespread commercialization of hydrogen fuel cell technology. UTC had access to MEA materials that had accrued significant load time under real-world conditions in PureMotion® 120 power plant used in transit buses. These materials are referred to as end-of-life (EOL) components in the rest of this document. Advanced characterization techniques were used to evaluate degradation mode progress using these critical cell components extracted from both bus power plants and corresponding materials tested using the DOE AST’s. These techniques were applied to samples at beginning-of-life (BOL) to serve as a baseline. These comparisons advised the progress of the various failure modes that these critical components were subjected to, such as membrane degradation, catalyst support corrosion, platinum group metal dissolution, and others. Gaps in the existing ASTs predicted the degradation observed in the field in terms of these modes were outlined. Using the gaps, new AST’s were recommended and tested to better reflect the degradation modes seen in field operation. Also, BOL components were degraded in a test vehicle at UTC designed to accelerate the bus field operation.

Flexible fuel cycle system for the transition from LWR to FBR

International Nuclear Information System (INIS)

Fukasawa, Tetsuo; Yamashita, Junichi; Hoshino, Kuniyoshi; Sasahira, Akira; Inoue, Tadashi; Minato, Kazuo; Sato, Seichi

2009-01-01

Japan will deploy commercial fast breeder reactor (FBR) from around 2050 under the suitable conditions for the replacement of light water reactor (LWR) with FBR. The transition scenario from LWR to FBR is investigated in detail and the flexible fuel cycle initiative (FFCI) system has been proposed as a optimum transition system. The FFCI removes ∼95% uranium from LWR spent fuel (SF) in LWR reprocessing and residual material named Recycle Material (RM), which is ∼1/10 volume of original SF and contains ∼50% U, ∼10% Pu and ∼40% other nuclides, is treated in FBR reprocessing to recover Pu and U. If the FBR deployment speed becomes lower, the RM will be stored until the higher speed again. The FFCI has some merits compared with ordinary system that consists of full reprocessing facilities for both LWR and FBR SF during the transition period. The economy is better for FFCI due to the smaller LWR reprocessing facility (no Pu/U recovery and fabrication). The FFCI can supply high Pu concentration RM, which has high proliferation resistance and flexibly respond to FBR introduction rate changes. Volume minimization of LWR SF is possible for FFCI by its conversion to RM. Several features of FFCI were quantitatively evaluated such as Pu mass balance, reprocessing capacities, LWR SF amounts, RM amounts, and proliferation resistance to compare the effectiveness of the FFCI system with other systems. The calculated Pu balance revealed that the FFCI could supply enough but no excess Pu to FBR. These evaluations demonstrated the applicability of FFCI system to the transition period from LWR to FBR cycles. (author)

Analysis of changes in the fuel component of the cost of electricity in the transition to a closed fuel cycle in nuclear power system

International Nuclear Information System (INIS)

Gurin, Andrey V.; Alekseev, P.N.

2017-01-01

This paper presents a study of scenarios of transition to a closed fuel cycle in the system of nuclear power, built basing on resource availability requirements at the stage of full life-cycle reactors. Conventionally, there are three main scenarios for the development of nuclear energy: with VVER reactors operating in an open fuel cycle; with VVER reactors operating in a closed fuel cycle; and co-operating VVER and BN, operating in a closed fuel cycle. For the considered scenarios, a quantitative estimation of change in time of material balances were performed, including spent fuel balance, balance of plutonium, reprocessed and depleted uranium, radioactive waste, and the analysis of the fuel component of the cost of electricity.

Analysis of changes in the fuel component of the cost of electricity in the transition to a closed fuel cycle in nuclear power system

Energy Technology Data Exchange (ETDEWEB)

Gurin, Andrey V. [National Research Centre ' ' Kurchatov Institute' ' , Moscow (Russian Federation); Alekseev, P.N.

2017-09-15

This paper presents a study of scenarios of transition to a closed fuel cycle in the system of nuclear power, built basing on resource availability requirements at the stage of full life-cycle reactors. Conventionally, there are three main scenarios for the development of nuclear energy: with VVER reactors operating in an open fuel cycle; with VVER reactors operating in a closed fuel cycle; and co-operating VVER and BN, operating in a closed fuel cycle. For the considered scenarios, a quantitative estimation of change in time of material balances were performed, including spent fuel balance, balance of plutonium, reprocessed and depleted uranium, radioactive waste, and the analysis of the fuel component of the cost of electricity.

Communication Buses and Protocols for Sensor Networks

Directory of Open Access Journals (Sweden)

Andrew Mason

2002-07-01

Full Text Available This paper overviews existing digital communication buses which are commonly used in sensor networks, discusses sensor network architectures, and introduces a new sensor bus for low power microsystem applications. The new intra-module multi-element microsystem (IM2 bus is nine-line interface with 8b serial data which implements several advanced features such as power management and plug-n-play while maintaining minimum hardware overhead at the sensor node. Finally, some issues in wireless sensor networking are discussed. The coverage of these issues provides a guideline for choosing the appropriate bus for different sensor network applications.

Bio-fuels for diesel engines: Experience in Italy and Europe

International Nuclear Information System (INIS)

Rocchietta, C.

1992-01-01

With the aim of meeting stringent European Communities air pollution regulations, reducing the necessity of petroleum imports and creating new markets for agricultural products, Italy's Ferruzzi-Montedison Group is developing diesel engine fuels derived from vegetable oils. The innovative feature of these fuels, from the environmental protection stand-point, is that they don't contain any sulfur, the main cause of acid rain. This paper provides brief notes of the key chemical-physical properties of these diesel fuels, whose application doesn't require any modifications to diesel engines, and assesses the relative production technologies and commercialization prospects. Reference is made to the results of recent performance tests conducted on buses and taxis

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children's exposure.

Science.gov (United States)

Hochstetler, Heather A; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H; Grinshpun, Sergey A

2011-03-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 µg m -3 . The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors).

Quantification of self pollution from two diesel school buses using three independent methods

Science.gov (United States)

Sally Liu, L.-J.; Phuleria, Harish C.; Webber, Whitney; Davey, Mark; Lawson, Douglas R.; Ireson, Robert G.; Zielinska, Barbara; Ondov, John M.; Weaver, Christopher S.; Lapin, Charles A.; Easter, Michael; Hesterberg, Thomas W.; Larson, Timothy

2010-09-01

We monitored two Seattle school buses to quantify the buses' self pollution using the dual tracers (DT), lead vehicle (LV), and chemical mass balance (CMB) methods. Each bus drove along a residential route simulating stops, with windows closed or open. Particulate matter (PM) and its constituents were monitored in the bus and from a LV. We collected source samples from the tailpipe and crankcase emissions using an on-board dilution tunnel. Concentrations of PM 1, ultrafine particle counts, elemental and organic carbon (EC/OC) were higher on the bus than the LV. The DT method estimated that the tailpipe and the crankcase emissions contributed 1.1 and 6.8 μg m -3 of PM 2.5 inside the bus, respectively, with significantly higher crankcase self pollution (SP) when windows were closed. Approximately two-thirds of in-cabin PM 2.5 originated from background sources. Using the LV approach, SP estimates from the EC and the active personal DataRAM (pDR) measurements correlated well with the DT estimates for tailpipe and crankcase emissions, respectively, although both measurements need further calibration for accurate quantification. CMB results overestimated SP from the DT method but confirmed crankcase emissions as the major SP source. We confirmed buses' SP using three independent methods and quantified crankcase emissions as the dominant contributor.

Current status of the post boiling transition research in Japan. Integrity evaluation of nuclear fuel assemblies after boiling transition and development of rewetting correlations

International Nuclear Information System (INIS)

Hara, Takashi; Mizokami, Shinya; Kudo, Yoshiro; Komura, Seiichi; Nagata, Yoshifumi; Morooka, Shinichi

2003-01-01

Development of rewetting correlation formula was the key to predict fuel-cladding temperature after Boiling Transition (BT). Japanese BWR utilities and vendors performed some tests of rewetting and made two rewetting correlation formulas. The effect on fuel integrity after BT depends on temperature of fuel rod and time of dryout. Main cause of losing fuel integrity during BWR's Anticipated Operational Occurrences (AOO) after BT is embrittlement of the claddings due to oxidation. Ballooning of fuel rod is excepted because its pressure boundary isn't broken. In Japan, the Standards Committee of Atomic Energy Society of Japan (AESJ) is making post BT standard. This standard provides guidelines based on the latest knowledge to judge fuel integrity in case of BT and the validity of reusing the fuel assembly that experienced BT in BWRs. (author)

Driving-behavior-aware stochastic model predictive control for plug-in hybrid electric buses

International Nuclear Information System (INIS)

Li, Liang; You, Sixiong; Yang, Chao; Yan, Bingjie; Song, Jian; Chen, Zheng

2016-01-01

Highlights: • The novel approximated global optimal energy management strategy has been proposed for hybrid powertrains. • Eight typical driving behaviors have been classified with K-means to deal with the multiplicative traffic conditions. • The stochastic driver models of different driving behaviors were established based on the Markov chains. • ECMS was used to modify the SMPC-based energy management strategy to improve its fuel economy. • The approximated global optimal energy management strategy for plug-in hybrid electric buses has been verified and analyzed. - Abstract: Driving cycles of a city bus is statistically characterized by some repetitive features, which makes the predictive energy management strategy very desirable to obtain approximate optimal fuel economy of a plug-in hybrid electric bus. But dealing with the complicated traffic conditions and finding an approximated global optimal strategy which is applicable to the plug-in hybrid electric bus still remains a challenging technique. To solve this problem, a novel driving-behavior-aware modified stochastic model predictive control method is proposed for the plug-in hybrid electric bus. Firstly, the K-means is employed to classify driving behaviors, and the driver models based on Markov chains is obtained under different kinds of driving behaviors. While the obtained driver behaviors are regarded as stochastic disturbance inputs, the local minimum fuel consumption might be obtained with a traditional stochastic model predictive control at each step, taking tracking the reference battery state of charge trajectory into consideration in the finite predictive horizons. However, this technique is still accompanied by some working points with reduced/worsened fuel economy. Thus, the stochastic model predictive control is modified with the equivalent consumption minimization strategy to eliminate these undesirable working points. The results in real-world city bus routines show that the

Fuel cell bus operation, system investigation H2 bus

International Nuclear Information System (INIS)

Anon.

1992-01-01

The WP covers two tasks: - Prepartion of Technical Catalogue: In cooperation with ICIL, AR have compiled a technical catalogue, providing the impartial descriptions, both of existing technology and regulations, and the likely future developments of these, as to remedy the first problem faced by a potential hydrogen bus fleet operator viz the absence of an impartial description of the available vehicle and fuels systems together with the absence of a description of regulatory and safety factors which need consideration. - Fuel Cell Bus Operation - System Investigation H 2 Bus: The application of fuel cell electric generation systems to hybrid electrical buses or electrical busses without any storage system on board is considered. The task will cover safety and environmental aspects, a cost estimate and a market evaluation. (orig.)

Uncertainty in particle number modal analysis during transient operation of compressed natural gas, diesel, and trap-equipped diesel transit buses.

Science.gov (United States)

Holmén, Britt A; Qu, Yingge

2004-04-15

The relationships between transient vehicle operation and ultrafine particle emissions are not well-known, especially for low-emission alternative bus technologies such as compressed natural gas (CNG) and diesel buses equipped with particulate filters/traps (TRAP). In this study, real-time particle number concentrations measured on a nominal 5 s average basis using an electrical low pressure impactor (ELPI) for these two bus technologies are compared to that of a baseline catalyst-equipped diesel bus operated on ultralow sulfur fuel (BASE) using dynamometer testing. Particle emissions were consistently 2 orders of magnitude lower for the CNG and TRAP compared to BASE on all driving cycles. Time-resolved total particle numbers were examined in terms of sampling factors identified as affecting the ability of ELPI to quantify the particulate matter number emissions for low-emitting vehicles such as CNG and TRAP as a function of vehicle driving mode. Key factors were instrument sensitivity and dilution ratio, alignment of particle and vehicle operating data, sampling train background particles, and cycle-to-cycle variability due to vehicle, engine, after-treatment, or driver behavior. In-cycle variability on the central business district (CBD) cycle was highest for the TRAP configuration, but this could not be attributed to the ELPI sensitivity issues observed for TRAP-IDLE measurements. Elevated TRAP emissions coincided with low exhaust temperature, suggesting on-road real-world particulate filter performance can be evaluated by monitoring exhaust temperature. Nonunique particle emission maps indicate that measures other than vehicle speed and acceleration are necessary to model disaggregated real-time particle emissions. Further testing on a wide variety of test cycles is needed to evaluate the relative importance of the time history of vehicle operation and the hysteresis of the sampling train/dilution tunnel on ultrafine particle emissions. Future studies should

Battery Peak Power Shaving Strategy to Prolong Battery Life for Electric Buses

NARCIS (Netherlands)

Pham, T.H.; Rosea, B.; Wilkins, S.

2016-01-01

This paper presents a battery peak power shaving strategy for battery electric buses. The developed strategy restricts the battery charge/discharge power when the propulsion power demand is high to avoid high deterioration of the battery capacity during operation. Without reducing the propulsion

Closed Nuclear Fuel Cycle Technologies to Meet Near-Term and Transition Period Requirements

International Nuclear Information System (INIS)

Collins, E.D.; Felker, L.K.; Benker, D.E.; Campbell, D.O.

2008-01-01

A scenario that very likely fits conditions in the U.S. nuclear power industry and can meet the goals of cost minimization, waste minimization, and provisions of engineered safeguards for proliferation resistance, including no separated plutonium, to close the fuel cycle with full actinide recycle is evaluated. Processing aged fuels, removed from the reactor for 30 years or more, can provide significant advantages in cost reduction and waste minimization. The UREX+3 separations process is being developed to separate used fuel components for reuse, thus minimizing waste generation and storage in geologic repositories. Near-term use of existing and new thermal spectrum reactors can be used initially for recycle actinide transmutation. A transition period will eventually occur, when economic conditions will allow commercial deployment of fast reactors; during this time, recycled plutonium can be diverted into fast reactor fuel and conversion of depleted uranium into additional fuel material can be considered. (authors)

Closed Nuclear Fuel Cycle Technologies to Meet Near-Term and Transition Period Requirements

Energy Technology Data Exchange (ETDEWEB)

Collins, E.D.; Felker, L.K.; Benker, D.E.; Campbell, D.O. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, Tennessee, 37831-6152 (United States)

2008-07-01

A scenario that very likely fits conditions in the U.S. nuclear power industry and can meet the goals of cost minimization, waste minimization, and provisions of engineered safeguards for proliferation resistance, including no separated plutonium, to close the fuel cycle with full actinide recycle is evaluated. Processing aged fuels, removed from the reactor for 30 years or more, can provide significant advantages in cost reduction and waste minimization. The UREX+3 separations process is being developed to separate used fuel components for reuse, thus minimizing waste generation and storage in geologic repositories. Near-term use of existing and new thermal spectrum reactors can be used initially for recycle actinide transmutation. A transition period will eventually occur, when economic conditions will allow commercial deployment of fast reactors; during this time, recycled plutonium can be diverted into fast reactor fuel and conversion of depleted uranium into additional fuel material can be considered. (authors)

A Feeder-Bus Dispatch Planning Model for Emergency Evacuation in Urban Rail Transit Corridors

Science.gov (United States)

Wang, Yun; Yan, Xuedong; Zhou, Yu; Zhang, Wenyi

2016-01-01

The mobility of modern metropolises strongly relies on urban rail transit (URT) systems, and such a heavy dependence causes that even minor service interruptions would make the URT systems unsustainable. This study aims at optimally dispatching the ground feeder-bus to coordinate with the urban rails’ operation for eliminating the effect of unexpected service interruptions in URT corridors. A feeder-bus dispatch planning model was proposed for the collaborative optimization of URT and feeder-bus cooperation under emergency situations and minimizing the total evacuation cost of the feeder-buses. To solve the model, a concept of dummy feeder-bus system is proposed to transform the non-linear model into traditional linear programming (ILP) model, i.e., traditional transportation problem. The case study of Line #2 of Nanjing URT in China was adopted to illustrate the model application and sensitivity analyses of the key variables. The modeling results show that as the evacuation time window increases, the total evacuation cost as well as the number of dispatched feeder-buses decrease, and the dispatched feeder-buses need operate for more times along the feeder-bus line. The number of dispatched feeder-buses does not show an obvious change with the increase of parking spot capacity and time window, indicating that simply increasing the parking spot capacity would cause huge waste for the emergent bus utilization. When the unbalanced evacuation demand exists between stations, the more feeder-buses are needed. The method of this study will contribute to improving transportation emergency management and resource allocation for URT systems. PMID:27676179

Modeling of passengers' safety perception for buses on mountainous roads.

Science.gov (United States)

Khoo, Hooi Ling; Ahmed, Muaid

2018-04-01

This study had developed a passenger safety perception model specifically for buses taking into consideration the various factors, namely driver characteristics, environmental conditions, and bus characteristics using Bayesian Network. The behaviour of bus driver is observed through the bus motion profile, measured in longitudinal, lateral, and vertical accelerations. The road geometry is recorded using GPS and is computed with the aid of the Google map while the perceived bus safety is rated by the passengers in the bus in real time. A total of 13 variables were derived and used in the model development. The developed Bayesian Network model shows that the type of bus and the experience of the driver on the investigated route could have an influence on passenger's perception of their safety on buses. Road geometry is an indirect influencing factor through the driver's behavior. The findings of this model are useful for the authorities to structure an effective strategy to improve the level of perceived bus safety. A high level of bus safety will definitely boost passenger usage confidence which will subsequently increase ridership. Copyright © 2018 Elsevier Ltd. All rights reserved.

Cost Probability Analysis of China's Nuclear Fuel Cycle Transition

International Nuclear Information System (INIS)

Gao, R. X.; Ko, W. I.; Lee, S. H.

2015-01-01

The Chinese government has already determined to develop the closed nuclear fuel cycle, its long-term roadmap of spent fuel management has not been decided yet. Currently, it seems that China's booming economy gives abundant financial assurance to develop nuclear programs in full play according to its near-term national plans. However, the viability and sustainability of nuclear power always depends critically on its economics. Therefore, it is necessary to conduct a well focused cost-benefit and objective analysis of China's ongoing nuclear power programs with the future prospects. In this study, we conduct a comparative analysis of electricity generation cost in four reference nuclear fuel cycle transition scenarios by 2050. Direct disposal is assumed to produce the cheapest LCT as low as 62.688 mills/kWh compared to the other options. However, after performing a relative uncertainty study, the results show that the capital cost of reactor is the key cost component which leads to the cost gap

Cost Probability Analysis of China's Nuclear Fuel Cycle Transition

Energy Technology Data Exchange (ETDEWEB)

Gao, R. X. [Univ. of Science and Technology, Daejeon (Korea, Republic of); Ko, W. I.; Lee, S. H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

The Chinese government has already determined to develop the closed nuclear fuel cycle, its long-term roadmap of spent fuel management has not been decided yet. Currently, it seems that China's booming economy gives abundant financial assurance to develop nuclear programs in full play according to its near-term national plans. However, the viability and sustainability of nuclear power always depends critically on its economics. Therefore, it is necessary to conduct a well focused cost-benefit and objective analysis of China's ongoing nuclear power programs with the future prospects. In this study, we conduct a comparative analysis of electricity generation cost in four reference nuclear fuel cycle transition scenarios by 2050. Direct disposal is assumed to produce the cheapest LCT as low as 62.688 mills/kWh compared to the other options. However, after performing a relative uncertainty study, the results show that the capital cost of reactor is the key cost component which leads to the cost gap.

76 FR 77888 - Student Transportation of America, Inc.-Control-Dairyland Buses, Inc.

Science.gov (United States)

2011-12-14

... Wisconsin law, also holds a FMCSA license (MC-170747) and is owned by Coach USA, Inc., a Delaware..., 2011, from their current owner, Coach USA, Inc., into an independent voting trust established under 49... Transportation of America, Inc.--Control--Dairyland Buses, Inc. AGENCY: Surface Transportation Board. ACTION...

High temperature phase transitions in nuclear fuels of the fourth generation

International Nuclear Information System (INIS)

De Bruycker, F.

2010-01-01

Understanding the behaviour of nuclear materials in extreme conditions is of prime importance for the analysis of the operation limits of nuclear fuels, and prediction of possible nuclear reactor accidents, relevant to the general objectives of nuclear safety research. The main purpose of this thesis is the study of high temperature phase transitions in nuclear materials, with special attention to the candidate fuel materials for the reactors of the 4. Generation. In this framework, material properties need to be investigated at temperatures higher than 2500 K, where equilibrium conditions are difficult to obtain. Laser heating combined with fast pyrometer is the method used at the European Institute for Transuranium Elements (JRC - ITU). It is associated to a novel process used to determine phase transitions, based on the detection, via a suited low-power (mW) probe laser, of changes in surface reflectivity that may accompany solid/liquid phase transitions. Fast thermal cycles, from a few ms up to the second, under almost container-free conditions and control atmosphere narrow the problem of vaporisation and sample interactions usually meet with traditional method. This new experimental approach has led to very interesting results. It confirmed earlier research for material systems known to be stable at high temperature (such as U-C) and allowed a refinement of the corresponding phase diagrams. But it was also feasible to apply this method to materials highly reactive, thus original results are presented on PuO 2 , NpO 2 , UO 2 -PuO 2 and Pu-C systems. (author)

Effects of Photovoltaic and Fuel Cell Hybrid System on Distribution Network Considering the Voltage Limits

Directory of Open Access Journals (Sweden)

ABYANEH, H. A.

2010-11-01

Full Text Available Development of distribution network and power consumption growth, increase voltage drop on the line impedance and therefore voltage drop in system buses. In some cases consumption is so high that voltage in some buses exceed from standard. In this paper, effect of the fuel cell and photovoltaic hybrid system on distribution network for solving expressed problem is studied. For determining the capacity of each distributed generation source, voltage limitation on the bus voltages under different conditions is considered. Simulation is done by using DIgSILENT software on the part of the 20 kV real life Sirjan distribution system. In this article, optimum location with regard to system and environmental conditions are studied in two different viewpoints.

Demonstration of 3 buses fuelled with ethanol with ignition improver in the Netherlands

NARCIS (Netherlands)

Verweij, J.; Weide, J. van der; Nie, L.H. de; Bruin, A. de

1996-01-01

This three year demonstration programme was initiated by OBL, a subsidiary of two Dutch sugar companies, and GADO, a public transport company. The programme was financially supported by a regional governmental organisation (ISP). In this programme, three bio-ethanol fuelled buses accumulated more

A fuel cell city bus with three drivetrain configurations

Energy Technology Data Exchange (ETDEWEB)

Wang, Junping [Key Laboratory of Education Ministry for Modern Design and Rotor-Bearing System, Xi' an Jiaotong University, Xi' an 710049 (China); Chen, Yong [School of Automobile and Transporting Engineering, Liaoning Institute of Technology, Jinzhou, Liaoning 121001 (China); Chen, Quanshi [State Key Laboratory of Automobile Safety and Energy Conservation, Tsinghua University, Beijing 100084 (China)

2006-09-22

Three fuel cell city buses of the energy hybrid- and power hybrid-type were re-engineered with three types of drivetrain configuration to optimize the structure and improve the performance. The energy distribution, hydrogen consumption, state of charge (SOC) and the power variation rate were analyzed when different drivetrain configurations and parameters were used. When powered only by a fuel cell, the bus cannot recover the energy through regenerative braking. The variation of the fuel cell power is large and frequent, which is not good for the fuel cell. When the fuel cell is linked to a battery pack in parallel, the bus can recover the energy through regenerative braking. The energy distribution is determined by the parameters of the fuel cell and the battery pack in the design stage to reduce the power variation rate of the fuel cell. When the fuel cell and DC/DC converter connected in series links the battery pack in parallel, energy can be recovered and the energy distribution can be adjusted online. The power variation rate of both the fuel cell and the battery pack are reduced. (author)

Challenges and Experiences with Electric Propulsion Transit Buses in the United States

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Gifford, M.

2003-11-01

Document provides background for transit agencies and fleets that are considering electric propulsion technologies. It tells them what to expect and plan for when implementing vehicles with electric propulsion systems.

CERDEC Fuel Cell Team: Military Transitions for Soldier Fuel Cells

Science.gov (United States)

2008-10-27

Fuel Cell (DMFC) (PEO Soldier) Samsung: 20W DMFC (CRADA) General Atomics & Jadoo: 50W Ammonia Borane Fueled PEMFC Current Fuel Cell Team Efforts...Continued Ardica: 20W Wearable PEMFC operating on Chemical Hydrides Spectrum Brands w/ Rayovac: Hydrogen Generators and Alkaline Fuel Cells for AA...100W Ammonia Borane fueled PEMFC Ultralife: 150W sodium borohydride fueled PEMFC Protonex: 250W RMFC and Power Manager (ARO) NanoDynamics: 250W SOFC

Agricultural transportation fuels

International Nuclear Information System (INIS)

Anon.

1993-01-01

The recommendations on the title subject are focused on the question whether advantages and disadvantages of agricultural fuels compared to fossil fuels justify the Dutch policy promotion of the use of agricultural products as basic materials for agricultural fuels. Attention is paid to energetic, environmental and economical aspects of both fuel types. Four options to apply agricultural transportation fuels are discussed: (1) 10% bio-ethanol in euro-unleaded gasoline for engines of passenger cars, equipped with a three-way catalyst; (2) the substitution of 15% methyl tertiair butyl ether (MTBE) by ethyl tertiair butyl ether (ETBE) as a substituent for lead in unleaded super plus gasoline (Sp 98) for engines of passenger cars, equipped with a three-way catalyst; (3) 50% KME (rapeseed oil ester) in low-sulfur diesel (0.05%S D) for engines of vans without a catalyst; and (4) the substitution of 0.05% S D by bio-ethanol or KME for buses with fuel-adjusted engines, equipped with a catalyst. Also the substitution by liquefied petroleum gas (LPG), compressed natural gas (CNG) or E 95 was investigated in option four. Each of the options investigated can contribute to a reduction of the use of fossil energy and the environmental effects of the use of fossil fuels, although some environmental effects from agricultural fuels must be taken into consideration. It is recommended to seriously pay attention to the promotion of agricultural fuels, not only in the Netherlands, but also in an international context. Policy instruments to be used in the stimulation of the use of such fuels are the existing European Community subsidies on fallow lands, exemption of the European Community energy levy, and the use of tax differentiation. Large-scale demonstration projects must be started to quantify hazardous emissions and to solve still existing technical problems. 8 figs., 3 tabs., refs., 4 appendices

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children’s exposure

Science.gov (United States)

Hochstetler, Heather A.; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H.; Grinshpun, Sergey A.

2015-01-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 µg m−3. The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors). PMID:25904818

New buses and links for data acquisition

International Nuclear Information System (INIS)

Mueller, H.; Bogaerts, A.; McLaren, R.; Parkman, C.; Linnhoefer, D.

1992-01-01

Bus standards for data acquisition have been vital for the construction and operation of medium and large HEP experiments. The recent industry bus standardisation effort will soon release the next generation of high performance buses and links for scalable systems. Prototype components, VLSI chips and board-level systems are already announced. Layers of the new bus specifications cover wide areas of applications and provide possibilities to define specific bus profiles by interest groups. New, innovative solutions which are needed for high rate experiments are becoming visible. These will provide novel architectural possibilities, very high bandwidth, fast silicon, industry support and new metric mechanical standards. Interconnected via standard bridges, different bus standards can be used to cover the varying requirements from the front ends to the computers. (orig.)

Evaluation of the use of bioethanol fuelled buses based on ambient air pollution screening and on-road measurements

Energy Technology Data Exchange (ETDEWEB)

López-Aparicio, S., E-mail: sla@nilu.no; Hak, C.

2013-05-01

Mitigation measures to reduce greenhouse gas emissions may have adverse effects on urban air quality and human exposure to harmful pollutants. The use of bioethanol fuelled vehicles is increasing worldwide and may create new undesired pollution effects. Different measurement campaigns were performed in a pilot study to contribute to the understanding of the consequences associated with the use of bioethanol blended fuel (E95) on a series of pollutants. Ambient screening measurements of NO{sub 2}, O{sub 3}, acetic acid, formaldehyde and acetaldehyde were performed at different urban locations, exposed and not exposed to the circulation of bioethanol buses. In addition, volatile organic compounds were measured at the exhaust pipe of a bioethanol fuelled bus, both under idling conditions (carbonyls; DNPH cartridge) and under on-road driving conditions applying online monitoring (PTR-TOF). Higher ambient acetaldehyde values were measured at locations exposed to bioethanol fuelled buses than at locations not exposed, and very high acetaldehyde and acetic acid values were measured from the exhaust pipe during driving conditions (acetaldehyde > 150 ppm; acetic acid ≈ 20–30 ppm) and modelled at close distance to the bioethanol bus. Human exposure to high concentration of acetaldehyde is expected, and it may involve a significantly increased chance in developing cancer. The high concentration of acetic acid will involve odour annoyance and significant material degradation or corrosion. - Highlights: ► Acetaldehyde levels above 150 ppm were measured from the bioethanol bus. ► High acetic acid levels (20–30 ppm) were measured from the bioethanol bus. ► Demonstrated usefulness of PTR-MS to evaluate non-criteria pollutants ► High levels of acetaldehyde and acetic acid are estimated in the dispersion plume. ► Climate mitigation measures may have adverse impact on air quality.

Evaluation of the use of bioethanol fuelled buses based on ambient air pollution screening and on-road measurements

International Nuclear Information System (INIS)

López-Aparicio, S.; Hak, C.

2013-01-01

Mitigation measures to reduce greenhouse gas emissions may have adverse effects on urban air quality and human exposure to harmful pollutants. The use of bioethanol fuelled vehicles is increasing worldwide and may create new undesired pollution effects. Different measurement campaigns were performed in a pilot study to contribute to the understanding of the consequences associated with the use of bioethanol blended fuel (E95) on a series of pollutants. Ambient screening measurements of NO 2 , O 3 , acetic acid, formaldehyde and acetaldehyde were performed at different urban locations, exposed and not exposed to the circulation of bioethanol buses. In addition, volatile organic compounds were measured at the exhaust pipe of a bioethanol fuelled bus, both under idling conditions (carbonyls; DNPH cartridge) and under on-road driving conditions applying online monitoring (PTR-TOF). Higher ambient acetaldehyde values were measured at locations exposed to bioethanol fuelled buses than at locations not exposed, and very high acetaldehyde and acetic acid values were measured from the exhaust pipe during driving conditions (acetaldehyde > 150 ppm; acetic acid ≈ 20–30 ppm) and modelled at close distance to the bioethanol bus. Human exposure to high concentration of acetaldehyde is expected, and it may involve a significantly increased chance in developing cancer. The high concentration of acetic acid will involve odour annoyance and significant material degradation or corrosion. - Highlights: ► Acetaldehyde levels above 150 ppm were measured from the bioethanol bus. ► High acetic acid levels (20–30 ppm) were measured from the bioethanol bus. ► Demonstrated usefulness of PTR-MS to evaluate non-criteria pollutants ► High levels of acetaldehyde and acetic acid are estimated in the dispersion plume. ► Climate mitigation measures may have adverse impact on air quality

Transportation of Wheelchair Seated Students in School Buses: A Review of State Policy

Science.gov (United States)

Moore, Britta; Fuhrman, Susan; Karg, Patricia

2010-01-01

This study quantitatively reviews publicly available state policies as they relate to the transportation of wheelchair-seated students in school buses. Inclusion of best practices in specially equipped school bus and driver training policies was assessed. Key points of interest within state policies were identified based on site visits, common…

Research and Development of Zinc Air Fuel Cell To Achieve Commercialization Final Report CRADA No. TC-1544-98

Energy Technology Data Exchange (ETDEWEB)

Cooper, J. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Haley, H. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-28

The specific goal of this project was to advance the development of the zinc air fuel cell (ZAFC) towards commercial readiness in different mobile applications, including motor bikes, passenger cars, vans, buses and off-road vehicles (golf carts, factory equipment), and different stationary applications including generator sets, uninterruptible power systems and electric utility loading leveling and distributive power.

Increasing Capacity of Intersections with Transit Priority

Directory of Open Access Journals (Sweden)

Yanxi Hao

2016-12-01

Full Text Available Dedicated bus lane (DBL and transit signal priority (TSP are two effective and low-cost ways of improving the reliability of transits. However, these strategies reduce the capacity of general traffic. This paper presents an integrated optimization (IO model to improve the performance of intersections with dedicated bus lanes. The IO model integrated geometry layout, main-signal timing, pre-signal timing and transit priority. The optimization problem is formulated as a Mix-Integer-Non-Linear-Program (MINLP that can be transformed into a Mix-Integer-Linear-Program (MILP and then solved by the standard branch-and-bound technique. The applicability of the IO model is tested through numerical experiment under different intersection layouts and traffic demands. A VISSIM micro simulation model was developed and used to evaluate the performance of the proposed IO model. The test results indicate that the proposed model can increase the capacity and reduce the delay of general traffic when providing priority to buses.

Natural gas as an alternative to crude oil in automotive fuel chains well-to-wheel analysis and transition strategy development

International Nuclear Information System (INIS)

Hekkert, M.P.; Hendriks, F.H.J.F.; Faaij, A.P.C.; Neelis, M.L.

2005-01-01

Road transport produces significant amounts of CO 2 by using crude oil as primary energy source. A reduction of CO 2 emissions can be achieved by implementing alternative fuel chains. This article studies CO 2 emissions and energy efficiencies by means of a well to wheel analysis of alternative automotive fuel chains, using natural gas (NG) as an alternative primary energy source to replace crude oil. The results indicate that NG-based hydrogen applied in fuel cell vehicles (FCVs) lead to largest CO 2 emission reductions (up to 40% compared to current practice). However, large implementation barriers for this option are foreseen, both technically and in terms of network change. Two different transition strategies are discussed to gradually make the transition to these preferred fuel chains. Important transition technologies that are the backbone of these routes are traditional engine technology fuelled by compressed NG and a FCV fuelled by gasoline. The first is preferred in terms of carbon emissions. The results furthermore indicate that an innovation in the conventional chain, the diesel hybrid vehicle, is more efficient than many NG-based chains. This option scores well in terms of carbon emissions and implementation barriers and is a very strong option for the future

Best Operational and Maintenance Practices for City Bus Fleets to Maximize Fuel Economy

OpenAIRE

Energy Sector Management Assistance Program

2011-01-01

In most large cities in developing countries, buses continue to be the public transport option of choice, carrying a large share of urban travelers. However, transit bus companies in these countries are often cash-strapped. In many cases, the operating cost per bus kilometer exceeds revenues and bus fares are often kept low irrespective of the cost of providing service. Many cities are dom...

Transition cycle fuel management problems of NPP Krsko; Problemi gospodarenje gorivom u prijelaznim ciklusima NE Krsko

Energy Technology Data Exchange (ETDEWEB)

Petrovic, B [Institut ' Rudjer Boskovic' , Zagreb (Yugoslavia); Pevec, D [Elektrotehnicki fakultet, Zagreb (Yugoslavia); Smuc, T; Urli, N [Institut ' Rudjer Boskovic' , Zagreb (Yugoslavia)

1989-07-01

Transition cycle fuel management problems are described and illustrated using results and experience attained during core reload design of NPP Krsko. Improved version of computer code package PSU-LEOPARD/Mcrac is successfully applied to NPP Krsko loading pattern design. (author)

High prevalence of EMRSA-15 in Portuguese public buses: a worrisome finding.

Directory of Open Access Journals (Sweden)

Roméo Rocha Simões

Full Text Available BACKGROUND: The nosocomial prevalence of methicillin resistant Staphylococcus aureus (MRSA in Portugal remains one of the highest in Europe and is currently around 50%. Transmission of S. aureus, including MRSA, occurs principally by direct human-to-human skin contact. However, S. aureus can survive for long periods on inanimate objects, which may represent an important reservoir for dissemination as well. METHODOLOGY/PRINCIPAL FINDINGS: Between May 2009 and February 2010, handrails of 85 public urban buses circulating in Oporto, Portugal, were screened for the occurrence of MRSA. Twenty-two (26% buses showed MRSA contamination. The molecular characterization of a total of 55 MRSA, by pulsed-field gel electrophoresis (PFGE, staphylococcal cassette chromosome (SCC mec typing, spa typing, and multilocus sequence typing (MLST, clustered the isolates into three clonal types. However, the overwhelming majority (n = 50; 91% of the isolates belonged to a single clone (PFGE A, spa types t747, t032, t025 or t020, ST22, SCCmec type IVh that exhibits the characteristics of the pandemic EMRSA-15, currently the major lineage circulating in Portuguese hospitals, namely in the Oporto region. Two additional clones were found but in much lower numbers: (i PFGE B, ST5, spa type t002, SCCmec IVa (n = 3, and (ii PFGE C, spa type t008, ST8, SCCmec IVa (n = 2. None of the 55 isolates was PVL positive. CONCLUSIONS/SIGNIFICANCE: Public buses in Oporto seem to be an important reservoir of MRSA of nosocomial origin, providing evidence that the major hospital-associated MRSA clone in Portugal is escaping from the primary ecological niche of hospitals to the community environment. Infection control measures are urgently warranted to limit the spread of EMRSA-15 to the general population and future studies are required to assess the eventual increase of MRSA in the Portuguese community, which so far remains low.

Orange County Transit/traffic Management Integration And Traveler Information Project: Evaluation Plan

OpenAIRE

Hall, R.; Hickman, M.

1996-01-01

This document focuses on a Field Operational Test (FOT) to develop an integrated information system for transit and traffic management and for traveler information that relies on Global Positioning System (GPS) equipped buses as probe vehicles. The document provides the evaluation plan for the FOT. The plan covers three principal elements: 1) Institutional, TMC Operator and Bus Operator, 2) Public Knowledge and Perceptions, and 3) System performance. The document provides an overall evaluatio...

Fuel poverty is facing a data challenge - Which strategies to struggle against fuel poverty? Propositions for an ecologic and social transition policy

International Nuclear Information System (INIS)

Erard, Timothee; Chancel, Lucas; Saujot, Mathieu

2015-01-01

The authors address three main questions: how are structured the network of actors and the tools for the struggle against fuel poverty, what are the specific data challenges faced by the actors and the possible responses, and which lessons can be learned for the governance of energy transition in its whole. After a presentation of the context of fuel poverty (analysis of tools for the struggle against fuel poverty, the use of social-energetic data), this study, based on about forty interviews of various actors and on a workshop, proposes an analysis framework which distinguishes six steps in the definition and implementation of policies of struggle against fuel poverty. After a description of the current status and an identification of required improvements for each step, the authors propose a set of recommendations, draw lessons for urban policies aimed at an ecologic transformation and a modernisation of the social protection system in terms of level of intervention, scope of actions, and ownership and access to data bases. These recommendations more particularly address the definition of fuel poverty, its diagnosis at the national and at the territorial level, a better identification of concerned households, and an assessment of existing arrangements

Alternative Energy Busing

Science.gov (United States)

LaFee, Scott

2012-01-01

In recent years, school districts have converted portions of their bus fleets to cleaner-burning, sometimes cheaper, alternative fossil fuels, such as compressed natural gas or propane. Others have adopted biodiesel, which combines regular diesel with fuel derived from organic sources, usually vegetable oils or animal fats. The number of biodiesel…

NYC's experience with low-sulfur diesel and particulate traps

Energy Technology Data Exchange (ETDEWEB)

Parsley, B. [New York City Transit Department of Buses, New York, NY (United States)

2001-07-01

The operation of the New York City Transit's (NYCT) Bus Department was reviewed with particular focus on program objectives and partners, results of field demonstrations, results of emissions testing, and future plans. NYCT operates a 4,489 bus fleet of diesel transit (3,516), diesel coach (380), diesel articulated (361), CNG transit (221) and hybrid transit (11) buses. This power point presentation presented the results of an evaluation of the particulate emissions reductions using Johnson Matthey's continuous regenerating technology (CRT) in conjunction with reduced sulfur diesel fuel. The applicability of the technology for both new 4-stroke and older 2-stroke diesel engines was also evaluated along with fuel parameters that can enhance future commercial success. New technology focuses on oxidation catalyst and wall-flow ceramic filters, as well as the reduction of sulfur diesel fuel. CRT success factors were presented. JM's project partners in this new technology are Corning, Equilon, and Environment Canada (which performs the emissions testing), New York State Department of Environmental Conservation, RAD Energy, and MTA New York City Transit bus operations. A total of 50 buses have been equipped with the CRT system in Manhattan for over one year now. CRT was found to produce the following emissions reductions: 88-98 per cent reduction in CO, HC, PM, but no effect on NOx. CRT produced 70-99 per cent reduction in toxic emissions of PAH, NPAH, carbonyls and volatile organic compounds. CRT also produced 99 per cent reduction in particulate matter counts across all size ranges, including the smallest particles. Based on the success of the pilot program, NYCT has committed to implementing clean diesel technology fleet-wide and plans to retire all 2 stroke engines. 2 tabs., 12 figs.

Research and development of a phosphoric acid fuel cell/battery power source integrated in a test-bed bus. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-30

This project, the research and development of a phosphoric acid fuel cell/battery power source integrated into test-bed buses, began as a multi-phase U.S. Department of Energy (DOE) project in 1989. Phase I had a goal of developing two competing half-scale (25 kW) brassboard phosphoric acid fuel cell systems. An air-cooled and a liquid-cooled fuel cell system were developed and tested to verify the concept of using a fuel cell and a battery in a hybrid configuration wherein the fuel cell supplies the average power required for operating the vehicle and a battery supplies the `surge` or excess power required for acceleration and hill-climbing. Work done in Phase I determined that the liquid-cooled system offered higher efficiency.

Environmental impact of alternative fuel on Tehran air pollution

International Nuclear Information System (INIS)

Ebtekar, T.

1995-01-01

Seventy percent of the air pollution in the city of Tehran stems from mobile sources, and in comparison with other major cities of the world, Iran's capital experiences one of the most polluted metropolitan areas. There exists a surplus of liquid petroleum gas (LPG) in the Persian Gulf and Iranian market, in addition, Iran possesses the second largest reservoir of natural gas in the world. These alternative energy resources create a favorable potential fuel for city of Tehran. Experiments carried out in Tehran indicate that in converting the taxis from gasoline to a dual fuel (LPG/gasoline) car or to a dual fuel natural gas vehicle (NGV) reduce all major pollutants (CO, HC, NOX, Pb) substantially. Following the author's recommendation, the number of LPG dispensing units in gas stations are increasing and the number of dual fuel taxis amount to several thousands in the metropolitan area. The conversion of diesel buses in the Tehran Public Transportation Corporation to natural gas (NGV) has been recommended by the author and vast experimental works are underway at the present time

The technologies for heavy vehicles motors and their fuels; Les technologies des moteurs de vehicules lourds et leurs carburants

Energy Technology Data Exchange (ETDEWEB)

Plassat, G

2005-07-01

The heavy vehicles are those the total weight (charged) is more than 3,5 tons. This document provides a comparative and parametric analysis of the main technologies developed for the future buses. A detailed presentation is done for each technique, as the operating principles and the advantages and disadvantages facing the today solution. More particularly the author presents the evolution of the diesel-fuel motor, the motor optimization for specific fuel as the natural gas and the liquefied petroleum gas, the hybrid thermal-electric motor, the hydrogen fuel cells, the biofuels and the de-pollution systems to eliminate the NO{sub X} and the particles. (A.L.B.)

Fuel tax incidence in developing countries. The case of Costa Rica

Energy Technology Data Exchange (ETDEWEB)

Blackman, Allen [Resources for the Future, 1616 P Street, N.W. Washington, DC (United States); Environment for Development Center for Central America, Turriabla (Costa Rica); Osakwe, Rebecca; Alpizar, Francisco [Environment for Development Center for Central America, Turriabla (Costa Rica)

2010-05-15

Although fuel taxes are a practical means of curbing vehicular air pollution, congestion, and accidents in developing countries - all of which are typically major problems - they are often opposed on distributional grounds. Yet few studies have investigated fuel tax incidence in a developing country context. We use household survey data and income-outcome coefficients to analyze fuel tax incidence in Costa Rica. We find that the effect of a 10% fuel price hike through direct spending on gasoline would be progressive, its effect through spending on diesel - both directly and via bus transportation - would be regressive (mainly because poorer households rely heavily on buses), and its effect through spending on goods other than fuel and bus transportation would be relatively small, albeit regressive. Finally, we find that the overall effect of a 10% fuel price hike through all types of direct and indirect spending would be neutral and the magnitude of this combined effect would be modest. We conclude that distributional concerns need not rule out using fuel taxes to address pressing public health and safety problems, particularly if gasoline and diesel taxes can be differentiated. (author)

Fuel tax incidence in developing countries. The case of Costa Rica

International Nuclear Information System (INIS)

Blackman, Allen; Osakwe, Rebecca; Alpizar, Francisco

2010-01-01

Although fuel taxes are a practical means of curbing vehicular air pollution, congestion, and accidents in developing countries - all of which are typically major problems - they are often opposed on distributional grounds. Yet few studies have investigated fuel tax incidence in a developing country context. We use household survey data and income-outcome coefficients to analyze fuel tax incidence in Costa Rica. We find that the effect of a 10% fuel price hike through direct spending on gasoline would be progressive, its effect through spending on diesel - both directly and via bus transportation - would be regressive (mainly because poorer households rely heavily on buses), and its effect through spending on goods other than fuel and bus transportation would be relatively small, albeit regressive. Finally, we find that the overall effect of a 10% fuel price hike through all types of direct and indirect spending would be neutral and the magnitude of this combined effect would be modest. We conclude that distributional concerns need not rule out using fuel taxes to address pressing public health and safety problems, particularly if gasoline and diesel taxes can be differentiated. (author)

Fuel tax incidence in developing countries: The case of Costa Rica

Energy Technology Data Exchange (ETDEWEB)

Blackman, Allen, E-mail: blackman@rff.or [Resources for the Future, 1616 P Street, N.W. Washington, DC (United States); Environment for Development Center for Central America, Turriabla (Costa Rica); Osakwe, Rebecca; Alpizar, Francisco [Environment for Development Center for Central America, Turriabla (Costa Rica)

2010-05-15

Although fuel taxes are a practical means of curbing vehicular air pollution, congestion, and accidents in developing countries-all of which are typically major problems-they are often opposed on distributional grounds. Yet few studies have investigated fuel tax incidence in a developing country context. We use household survey data and income-outcome coefficients to analyze fuel tax incidence in Costa Rica. We find that the effect of a 10% fuel price hike through direct spending on gasoline would be progressive, its effect through spending on diesel-both directly and via bus transportation-would be regressive (mainly because poorer households rely heavily on buses), and its effect through spending on goods other than fuel and bus transportation would be relatively small, albeit regressive. Finally, we find that the overall effect of a 10% fuel price hike through all types of direct and indirect spending would be neutral and the magnitude of this combined effect would be modest. We conclude that distributional concerns need not rule out using fuel taxes to address pressing public health and safety problems, particularly if gasoline and diesel taxes can be differentiated.

Characterization and speciation of fine particulate matter inside the public transport buses running on bio-diesel.

Science.gov (United States)

2009-09-01

Air pollution with respect to particulate matter was investigated in Toledo, Ohio, USA, a : city of approximately 300,000, in 2009. Two study buses were selected to reflect typical : exposure conditions of passengers while traveling in the bus. Monit...

Technical Approach and Plan for Transitioning Spent Nuclear Fuel (SNF) Project Facilities to the Environmental Restoration Program

International Nuclear Information System (INIS)

SKELLY, W.A.

1999-01-01

This document describes the approach and process in which the 100-K Area Facilities are to be deactivated and transitioned over to the Environmental Restoration Program after spent nuclear fuel has been removed from the K Basins. It describes the Transition Project's scope and objectives, work breakdown structure, activity planning, estimated cost, and schedule. This report will be utilized as a planning document for project management and control and to communicate details of project content and integration

Development of generalized boiling transition model applicable for wide variety of fuel bundle geometries. Basic strategy and numerical approaches

International Nuclear Information System (INIS)

Ninokata, Hisashi; Sadatomi, Michio; Okawa, Tomio

2003-01-01

In order to establish a key technology to realize advanced BWR fuel designs, a three-year project of the advanced subchannel analysis code development had been started since 2002. The five dominant factors involved in the boiling transitional process in the fuel bundles were focused. They are, (1) inter-subchannel exchanges, (2) influences of obstacles (3) dryout of liquid film, (4) transition of two-phase flow regimes and (5) deposition of droplets. It has been recognized that present physical models or constitutive equations in subchannel formulations need to be improved so that they include geometrical effects in the fuel bundle design more mechanistically and universally. Through reviewing literatures and existent experimental results, underlying elementary processes and geometrical factors that are indispensable for improving subchannel codes were identified. The basic strategy that combines numerical and experimental approaches was proposed aiming at establishment of mechanistic models for the five dominant factors. In this paper, the present status of methodologies for detailed two-phase flow studies has been summarized. According to spatial scales of focused elementary processes, proper numerical approaches were selected. For some promising numerical approaches, preliminary calcitonins were performed for assessing their applicability to investigation of elementary processes involved in the boiling transition. (author)

Voluntary Truck and Bus Fuel-Economy-Program marketing plan. Final technical report, September 29, 1980-January 29, 1982

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

The aim of the program is to improve the utilization of fuel by commercial trucks and buses by updating and implementing specific approaches for educating and monitoring the trucking industry on methods and means of conserving fuels. The following outlines the marketing plan projects: increase use of program logo by voluntary program members and others; solicit trade publication membership and support; brief Congressional delegations on fuel conservation efforts; increase voluntary program presence before trade groups; increase voluntary program presence at truck and trade shows; create a voluntary program display for use at trade shows and in other areas; review voluntary program graphics; increase voluntary program membership; and produce placemats carrying fuel conservation messages; produce a special edition of Fuel Economy News, emphasizing the driver's involvement in fuel conservation; produce posters carrying voluntary program fuel conservation message. Project objectives, activities, and results for each project are summarized.

Vienna: a capital transported by LPG

International Nuclear Information System (INIS)

Anon.

1996-01-01

For more than 30 years the Austrian capital has chosen the LPG-fuel for its public transportation systems. This choice was advised by the environmental necessity to reduce the emissions of particulates from diesel engines and by the economical will of having a competitive fuel source with respect to diesel fuel. This paper recalls first the historical evolution of Vienna's buses progressively equipped with dual-fuel engines, and since 1976 with LPG fuel engines only. Today's the LPG buses fleet represents about 80% of the Vienna Transport buses. Then, the economical (fuel consumption, investment, exploitation and maintenance costs) and environmental (particulates and CO emissions) balance-sheet of this evolution is analysed. Since 1988, the use of catalytic converters for exhaust systems has allowed a 80% reduction of NOx emissions. (J.S.)

Secondary fuel delivery system

Science.gov (United States)

Parker, David M.; Cai, Weidong; Garan, Daniel W.; Harris, Arthur J.

2010-02-23

A secondary fuel delivery system for delivering a secondary stream of fuel and/or diluent to a secondary combustion zone located in the transition piece of a combustion engine, downstream of the engine primary combustion region is disclosed. The system includes a manifold formed integral to, and surrounding a portion of, the transition piece, a manifold inlet port, and a collection of injection nozzles. A flowsleeve augments fuel/diluent flow velocity and improves the system cooling effectiveness. Passive cooling elements, including effusion cooling holes located within the transition boundary and thermal-stress-dissipating gaps that resist thermal stress accumulation, provide supplemental heat dissipation in key areas. The system delivers a secondary fuel/diluent mixture to a secondary combustion zone located along the length of the transition piece, while reducing the impact of elevated vibration levels found within the transition piece and avoiding the heat dissipation difficulties often associated with traditional vibration reduction methods.

Power distribution investigation in the transition phase of the low moderation type MOX fueled LWR from the high conversion core to the breeding core

International Nuclear Information System (INIS)

Akie, Hiroshi; Nakano, Yoshihiro; Okubo, Tsutomu

2011-01-01

The key concept of Innovative Water Reactor for Flexible Fuel Cycle (FLWR) is a core transition from a high conversion (HC) type to a plutonium breeding (BR) type in a same reactor system only by replacing fuel assemblies. Consequently in this transition phase, there are two types of assemblies in the same core. Due to the differences of the two assembly types, region-wise soft to hard neutron spectra appears and result in a large power peaking. Therefore, power distribution of FLWR in the HC to BR transition phase was studied by performing assembly and core calculations. For the whole core calculation, a new 14-group energy structure is developed to better represent the power distribution obtained with the fine 107-group structure than the 9-group structure in the previous evaluations. Calculations on few assemblies geometries show large local power peakings can be effectively reduced by considering plutonium enrichment distribution in an assembly. In the whole core calculation, there is a power level mismatch between HC and BR assemblies, but overall power distribution flattening is possible by optimizing fuel assemblies loading. Although the fuel loading should be decided also taking into account the void coefficient, transition from HC to BR type FLWR seems feasible without difficulty. (author)

Real-world operation conditions and on-road emissions of Beijing diesel buses measured by using portable emission measurement system and electric low-pressure impactor.

Science.gov (United States)

Liu, Zhihua; Ge, Yunshan; Johnson, Kent C; Shah, Asad Naeem; Tan, Jianwei; Wang, Chu; Yu, Linxiao

2011-03-15

On-road measurement is an effective method to investigate real-world emissions generated from vehicles and estimate the difference between engine certification cycles and real-world operating conditions. This study presents the results of on-road measurements collected from urban buses which propelled by diesel engine in Beijing city. Two widely used Euro III emission level buses and two Euro IV emission level buses were chosen to perform on-road emission measurements using portable emission measurement system (PEMS) for gaseous pollutant and Electric Low Pressure Impactor (ELPI) for particulate matter (PM) number emissions. The results indicate that considerable discrepancies of engine operating conditions between real-world driving cycles and engine certification cycles have been observed. Under real-world operating conditions, carbon monoxide (CO) and hydrocarbon (HC) emissions can easily meet their respective regulations limits, while brake specification nitrogen oxide (bsNO(x)) emissions present a significant deviation from its corresponding limit. Compared with standard limits, the real-world bsNO(x) emission of the two Euro III emission level buses approximately increased by 60% and 120% respectively, and bsNO(x) of two Euro IV buses nearly twice standard limits because Selective Catalytic Reduction (SCR) system not active under low exhaust temperature. Particle mass were estimated via particle size distribution with the assumption that particle density and diameter is liner. The results demonstrate that nanometer size particulate matter make significant contribution to total particle number but play a minor role to total particle mass. It is suggested that specific certified cycle should be developed to regulate bus engines emissions on the test bench or use PEMS to control the bus emissions under real-world operating conditions. Copyright © 2010 Elsevier B.V. All rights reserved.

Itinerant vending of medicines inside buses in Nigeria: vending strategies, dominant themes and medicine-related information provided.

Science.gov (United States)

Yusuff, Kazeem B; Wassi Sanni, Abd'

2011-07-01

To determine vending strategies and marketing themes employed by itinerant bus vendors, and assess the accuracy and completeness of information provided on medicines being sold in an urban setting in Nigeria. Cross-sectional study and content analysis of itinerant vending of medicines inside buses recorded with a mobile telephone on purposively selected routes in a mega city with an estimated 18 million residents in southwestern Nigeria over a 2-month period. Two coders independently assessed 192 vending episodes by 56 vendors for 147 OTC and prescription medicines. Inter-rater reliability (Gwet AC1 =0.924; p<0.0001). Fourteen thousands and four hundred potential consumers encountered 192 recorded episodes of vending of medicines inside 192 buses within the study periods. Forty-four (78•5%) of the 56 vendors were females in the 30-45 years age bracket, were mostly (75%) attired in the local 'Iro and Buba' Ankara fabric and showed laminated identity cards (97.5%) issued by the local association for 'marketers' of medicines inside buses, markets, and motor parks. Of the 14400 consumers encountered inside buses during the study period, between 6.7% and 48.3% purchased the medicines promoted. Prayers against death from road traffic accidents and diseases of physical and / or meta-physical origins were the most frequently used (76•8%) ice-breaking opening statement / strategy to gain consumers' attention. Hematinics, multi-vitamins, simple analgesic, NSAIDs and corticosteroids were the most frequently vended medicines. Consumers' enquiries were related to dosing for children (51.8%), elderly (28.6%), and pregnancy (52.7%); and contra-indications during pregnancy (8.9%). Factual medicines information such as dose, frequency, potential side effects and contra-indications were not provided in majority of vending episodes. Itinerant vending of medicines and the use of misleading and melodramatic themes to secure high consumer patronage appear considerable in Nigeria

Developing a Natural Gas-Powered Bus Rapid Transit Service: A Case Study on Leadership: Roaring Fork Transportation Authority (Presentation); NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

Schroeder, A.

2015-03-01

The Roaring Fork Transportation Authority (RFTA) represents a series of unique successes in alternative fuel deployment by pushing the envelope with innovative solutions. In the last year, RFTA demonstrated the ability to utilize compressed natural gas buses at a range of altitudes, across long distances, in extreme weather conditions and in a modern indoor fueling and maintenance facility - allwhile saving money and providing high-quality customer service. This case study will highlight how the leadership of organizations and communities that are implementing advances in natural gas vehicle technology is paving the way for broader participation.

Thermal margin model for transition core of KSNP

International Nuclear Information System (INIS)

Nahm, Kee Yil; Lim, Jong Seon; Park, Sung Kew; Chun, Chong Kuk; Hwang, Sun Tack

2004-01-01

The PLUS7 fuel was developed with mixing vane grids for KSNP. For the transition core partly loaded with the PLUS7 fuels, the procedure to set up the optimum thermal margin model of the transition core was suggested by introducing AOPM concept into the screening method which determines the limiting assembly. According to the procedure, the optimum thermal margin model of the first transition core was set up by using a part of nuclear data for the first transition and the homogeneous core with PLUS7 fuels. The generic thermal margin model of PLUS7 fuel was generated with the AOPM of 138%. The overpower penalties on the first transition core were calculated to be 1.0 and 0.98 on the limiting assembly and the generic thermal margin model, respectively. It is not usual case to impose the overpower penalty on reload cores. It is considered that the lack of channel flow due to the difference of pressure drop between PLUS7 and STD fuels results in the decrease of DNBR. The AOPM of the first transition core is evaluated to be about 135% by using the optimum generic thermal margin model which involves the generic thermal margin model and the total overpower penalty. The STD fuel is not included among limiting assembly candidates in the second transition core, because they have much lower pin power than PLUS7 fuels. The reduced number of STD fuels near the limiting assembly candidates the flow from the limiting assembly to increase the thermal margin for the second transition core. It is expected that cycle specific overpower penalties increase the thermal margin for the transition core. Using the procedure to set up the optimum thermal margin model makes sure that the enhanced thermal margin of PLUS7 fuel can be sufficiently applied to not only the homogeneous core but also the transition core

Models of fuel masses transition during second stage of the accident on Chernobyl NPP

International Nuclear Information System (INIS)

Tarapon, A.

2002-01-01

In ISPE NASU of Ukraine are developed mathematical models and software, which allow to research the processes of fuel masses transition during the accident at ChNPP. We found out, that the main reason of accident on ChNPP is the happening in the reactor of crisis of heat exchange of the second sort, instead of the effect positive output of reactivity from displacers of rods of system of emergency protection, as is accepted in official version

Walking School Buses as a Form of Active Transportation for Children--A Review of the Evidence

Science.gov (United States)

Smith, Liz; Norgate, Sarah H.; Cherrett, Tom; Davies, Nigel; Winstanley, Christopher; Harding, Mike

2015-01-01

Background: Walking school buses (WSBs) offer a potentially healthier way for children to get to school while reducing traffic congestion. A number of pressing societal challenges make it timely to evaluate evidence of their value. Methods: Studies that focused solely on WSBs were identified through online and manual literature searches. Twelve…

New Britain, Conn. School District will Benefit from $125,000 EPA Rebate for Clean Emission School Buses

Science.gov (United States)

The New Britain, Conn. school district will benefit from a $125,000 US EPA rebate that will pay for retrofitted engines on seven older school buses so they would emit fewer pollutants that are linked to health problems such as asthma and lung damage.

A Transition Strategy from Fossil Fuels to Renewable Energy Sources in the Mexican Electricity System

Directory of Open Access Journals (Sweden)

Juan J. Vidal-Amaro

2018-03-01

Full Text Available Renewable energy sources exploitation acquires special importance for creating low-carbon energy systems. In Mexico a national regulation limits the fossil fuel-based electricity generation to 65%, 60% and 50% by years 2024, 2030 and 2050 respectively. This study evaluates several scenarios of renewables incorporation into the Mexican electricity system to attend those targets as well as a 75% renewables-based electricity share target towards a 100% renewable system. By its size, the Mexican electricity system, with a generation of 260.4 TWh/year (85% based on fossil fuels, can be regarded as an illustrating reference. The impact of increasing amounts of wind, photovoltaic solar, biomass, biogas, geothermal, hydro and concentrating solar power on the system’s capacity to attend demand on a one-hour timescale resolution is investigated utilizing the EnergyPLAN model and the minimum total mix capacity method. Possible excess of electricity production is also assessed. For every target year, a solution is obtained corresponding to the combination resulting in the minimum total generation capacity for the electricity system. A transition strategy to a system with a high share of renewables-based electricity is designed where every transition step corresponds to the optimal energy mix for each of the target years.

Can propulsion and fuel diversity for the bus fleet achieve the win–win strategy of energy conservation and environmental protection?

International Nuclear Information System (INIS)

Wang, Renjie; Wu, Ye; Ke, Wenwei; Zhang, Shaojun; Zhou, Boya; Hao, Jiming

2015-01-01

Highlights: • We first report WTW energy and environmental impacts of new-energy buses in China. • Both CNGV and BEV eliminate petroleum use but increase the burden of other fossil fuels. • BEV is the best to reduce WTW NO X and VOC emissions but no benefit for PM 2.5 and SO 2 . • CNGV has PM 2.5 emission reductions by 70% greater than DV but no benefit in GHG emissions. • HEV is the only option that can reduce energy use and pollutant emissions at the same time. - Abstract: China is facing serious issues involving energy sufficiency, greenhouse gas (GHG) emissions and air pollution caused partly by the rapid growth of vehicles. In order to relieve those problems, new energy vehicles are introduced into the bus and car market. We adopt life cycle analysis to evaluate the well-to-wheels (WTW) energy consumption, CO 2 emissions and pollutant emissions from the traditional diesel bus and new energy buses, including diesel hybrid electric vehicles (HEVs), compressed natural gas vehicles (CNGVs) and battery electric vehicles (BEVs). This study reports the current situation and projects future scenarios for the BEV bus for several regions in China due to significant regional differences in the power generation mix. Compared to the diesel bus, the HEV bus can reduce petroleum, fossil fuel use and CO 2 emissions by about 20%, and, at the same time, produce stable reduction benefits for all air pollutants. The CNG bus achieves reductions of WTW primary PM 2.5 emissions by 70% over its diesel counterpart and, of course, uses little petroleum; but increases fossil fuel consumption moderately and has no benefit in GHG emissions. The BEV bus can deliver a substantial petroleum consumption advantage and greatly reduce the WTW NO X , VOC and CO emissions; but, if the electricity is generated from burning coal, the BEV bus has no PM 2.5 emission benefit compared to the conventional diesel bus. Currently, the BEV bus increases fossil energy use and CO 2 emissions in the

Bus fuel consumption model

Energy Technology Data Exchange (ETDEWEB)

Zargari, S.A. [Iran Univ. of Science and Technology, Teheran (Iran, Islamic Republic of); Khan, A.M. [Carleton Univ., Ottawa, ON (Canada). Dept. of Civil and Environmental Engineering

2000-07-01

The interest in rapid bus transit has increased sharply with the realization that modern metropolitan areas rely on public transit to provide for strong economies and communities. As a prevention tool against traffic congestion, deteriorating air quality and rising greenhouse gas emissions, this study of bus fuel consumption was designed to assist in the planning and management of rapid bus transit. The Australian Road Research Board's (ARRB) Road Fuel Consumption Model was used as a starting point. The estimations required were realized with the help of Newtonian Mechanics. The four states of vehicular traffic were examined: acceleration, cruise, deceleration, and idle. The estimated total power required from the engine to overcome resistance forces, to run vehicle accessories and overcome internal engine friction was calculated. The data for the standard and articulated bus was obtained from OC Transpo in Ottawa. The study permitted the authors to conclude that the estimations for the parameters for power requirements and fuel consumption for heavy duty vehicles are appropriate. The methodology for the estimation of fuel consumption on the Transitway, which is part of the rapid bus transit system, proved adequate. In addition, the methodology was useful to estimate fuel savings resulting from demand management strategies with potential for modal shift. 9 refs., 6 tabs.

Comparable Measures of Accessibility to Public Transport Using the General Transit Feed Specification

Directory of Open Access Journals (Sweden)

Jinjoo Bok

2016-03-01

Full Text Available Public transport plays a critical role in the sustainability of urban settings. The mass mobility and quality of urban lives can be improved by establishing public transport networks that are accessible to pedestrians within a reasonable walking distance. Accessibility to public transport is characterized by the ease with which inhabitants can reach means of transportation such as buses or metros. By measuring the degree of accessibility to public transport networks using a common data format, a comparative study can be conducted between different cities or metropolitan areas with different public transit systems. The General Transit Feed Specification (GTFS by Google Developers allows this by offering a common format based on text files and sharing the data set voluntarily produced and contributed by the public transit agencies of many participating cities around the world. This paper suggests a method to assess and compare public transit accessibility in different urban areas using the GTFS feed and demographic data. To demonstrate the value of the new method, six examples of metropolitan areas and their public transit accessibility are presented and compared.

Ethanol: The fuel of the future and its environmental impact

International Nuclear Information System (INIS)

Marek, N.J.; Evanoff, J.

1999-01-01

There are several major environmental benefits associated with using biomass-derived ethanol as a transportation fuel. First, because ethanol is produced from plant material (primarily corn) that uses atmospheric CO 2 for the process of photosynthesis, the combustion of biomass-derived ethanol can be viewed as recycling of CO 2 back into the atmosphere, thereby closing the carbon cycle. Further, emission tests on vehicles using E-85 (a blend of 85% denatured ethanol and 15% gasoline) show significant reductions in hydrocarbon and CO emission levels when compared to their gasoline counterparts. Finally, a recent study comparing greenhouse gas emissions from vehicles using E-10 (a blend of 10% ethanol and 90% gasoline, commonly called gasohol) and E-85 fuel to those using gasoline and diesel fuel has been completed by Argonne National Laboratory. Using the most recent energy input data available, the study concluded that corn-derived ethanol reduces greenhouse gases by 2--3% for E-10, and by over 30% for vehicles using E-85 fuel. Additionally, the state of Illinois, with several other corporate and privates partners, is testing the use of a new fuel formulation called OxyDiesel, a blend of 15% ethanol, diesel fuel, and a special blending additive, that holds considerable promise in reducing harmful tailpipe and greenhouse gas emissions from heavy-duty diesel engines in trucks, buses, and other diesel engine applications

Operational integrity using field buses; Integridade operacional utilizando barramentos de campo

Energy Technology Data Exchange (ETDEWEB)

Hennig, Carlos Henrique [Coester Automacao S.A., Sao Leopoldo, RS (Brazil)

2004-07-01

The device information is collected using standardized Filed Buses with high data transmission capacity, which allows the analysis of his operational status in real time. The quantity of information generated by the devices for the maintenance area is increasing and this data quantity transferred through the field bus should not interfere in the network performance to the point of degrade his control function. In this way, is presented a technique that can be used in different protocols, which allow sending of maintenance data using a small band of the communication channel. Operational integrity can be achieved using predictive maintenance techniques based on the collected data. (author)

Fuel Cycle Concept with Advanced METMET and Composite Fuel in LWRs

International Nuclear Information System (INIS)

Savchenko, A.; Skupov, M.; Vatulin, A.; Glushenkov, A.; Kulakov, G.; Lipkina, K.

2014-01-01

The basic factor that limits the serviceability of fuel elements developing in the framework of RERTR Program (transition from HEU to LEU fuel of research reactors) is interaction between U10Mo fuel and aluminium matrix . Interaction results in extra swelling of fuels, disappearance of a heat conducting matrix, a temperature rise in the fuel centre, penetration porosity, etc. Several methods exist to prevent fuel-matrix interaction. In terms of simplifying fuel element fabrication technology and reducing interaction, doping of fuel is the most optimal version

Low-Cost Methane Liquefaction Plant and Vehicle Refueling Station

International Nuclear Information System (INIS)

Wilding, B.; Bramwell, D.

1999-01-01

The Idaho National Engineering and Environmental Laboratory (INEEL) is currently negotiating a collaborative effort with Pacific Gas and Electric (PG and E) that will advance the use of liquefied natural gas (LNG) as a vehicle fuel. We plan to develop and demonstrate a small-scale methane liquefaction plant (production of 5,000 to 10,000 gallons per day) and a low-cost ($150,000) LNG refueling station to supply fuel to LNG-powered transit buses and other heavy-duty vehicles. INEEL will perform the research and development work. PG and E will deploy the new facilities commercially in two demonstration projects, one in northern California, and one in southern California

49 CFR Appendix F to Part 222 - Diagnostic Team Considerations

Science.gov (United States)

2010-10-01

..., public safety or law enforcement, engineering personnel from the State agency responsible for grade... freight; 4. Accident history for each crossing under consideration; 5. School bus or transit bus use at... at any of the crossings? 14. If school buses or transit buses use crossings within the proposed quiet...

Modelling and design optimization of low speed fuel cell - battery hybrid electric vehicles. Paper no. IGEC-1-125

International Nuclear Information System (INIS)

Guenther, M.; Dong, Z.

2005-01-01

A push for electric vehicles has occurred in the past several decades due to various concerns about air pollution and the contribution of emissions to global climate change. Although electric cars and buses have been the focus of much of electric vehicle development, smaller vehicles are used extensively for transportation and utility purposes in many countries. In order to explore the viability of fuel cell - battery hybrid electric vehicles, empirical fuel cell system data has been incorporated into the NREL's vehicle design and simulation tool, ADVISOR (ADvanced Vehicle SimulatOR), to predict the performance of a low-speed, fuel cell - battery electric vehicle through MATLAB Simulink. The modelling and simulation provide valuable feedback to the design optimization of the fuel cell power system. A sampling based optimization algorithm was used to explore the viability and options of a low cost design for urban use. (author)

Ex-vessel nuclear fuel transfer system

International Nuclear Information System (INIS)

Wade, E.E.

1978-01-01

A system for transferring fuel assemblies between a fuel transfer area and a fuel storage area while the fuel assemblies remain completely submerged in a continuous body of coolant is described. A fuel transfer area filled with reactor coolant communicating with the reactor vessel below the reactor coolant level provides a transfer area for fuel assemblies in transit to and from the reactor vessel. A positioning mechanism comprising at least one rotatable plug disposed on a fuel transfer tank located outside the reactor vessel cooperates with either the fuel transfer area or the fuel storage area to position a fuel assembly in transit. When in position, a transporting mechanism cooperating with the positioning mechanism lifts or lowers a chosen fuel assembly. The transporting mechanism together with the positioning mechanism are capable of transferring a fuel assembly between the fuel transfer area and the fuel storage area

Report on FS survey for project of introduction of highly energy-efficient trolley buses into the Mexico Metropolitan Area in FY 1997; 1997 nendo chosa hokokusho (Mexico city eno sho energy gata trolley bus donyu project FS chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Traffic jam and air pollution by automobiles are currently getting severe in the Mexico Metropolitan Area. Trolley buses were introduced for improving the environment more than ten years ago. Vehicles become too old for use, and their energy efficiency is low. In this project, 200 highly energy-efficient trolley buses are introduced to replace old inefficient trolley buses, which results in the improved traffic convenience in the City and enhanced energy efficiency. The new energy-efficient trolley buses are made of energy-efficient control VVVF inverters produced and exported by MELCO (Mitsubishi Electric Corporation), energy-efficient motors by MELMEX (Mitsubishi Electric Corporation, Mexico), and bodies by MASA which is a major manufacturer of bus bodies. The objective of this research is to analyze the background of introduction of new energy-efficient trolley buses and the effects of the present project. The results of analysis are going to be utilized for future promotion of the Joint Implementation and Clean Development Mechanism. 30 refs., 30 figs., 24 tabs.

How can we ensure the energy transition? Comment assurer la transition energetique?

Energy Technology Data Exchange (ETDEWEB)

Rojey, Alexandre

2007-07-01

With a continuously growing energy demand, the present energy model is clearly unsustainable due to the decline of fossil fuel resources and the risks of climate change A transition towards a sustainable model is therefore needed. However, there are no immediate alternatives leading to a sharp reduction in the use of fossil fuels, which are expected to maintain a major role for many years. The energy transition will therefore require a long time period The risks of climate change will require urgent measures and the 'carbon transition' has to be achieved more rapidly than the energy transition itself. A whole set of solutions will be needed in the technical but also economic and regulatory areas, for achieving a successful transition: energy conservation, diversification of energy . sources, reduction of the carbon content of the energy mix, CO{sub 2}, capture and storage. Hybrid options will be favoured. The paper describes the main features of the upcoming transition and the actions which are required. (auth)

Chicopee, Mass. School District will Benefit from $200,000 EPA Rebate to Clean Up Emissions from School Buses

Science.gov (United States)

A school district in Chicopee., Mass. will benefit from $200,000 from the US EPA that will pay for rebates to retrofit the engines on 10 older school buses so they would emit fewer pollutants that are linked to health problems such as asthma & lung damage.

Energy access and transition to cleaner cooking fuels and technologies in Sri Lanka: Issues and policy limitations

International Nuclear Information System (INIS)

Wickramasinghe, Anoja

2011-01-01

Easy energy access is a trigger for human, social, and economic development. A research project was undertaken in Sri Lanka to broaden the understanding of human dimension of energy access and technologies. A questionnaire survey, covering 2269 households, gathered data on socio-economic contexts and issues influencing a transition towards clean cooking facilities. The findings reveal that the transition is impeded by four factors: the lack of motivation and the pressure for switching over to cleaner facilities, the lack of modern energy technology options, the financial risks, and the lack of financing and other support. The paper describes the delicate two-way interrelation between women earning wages and the transitions to cleaner cooking fuels and technologies. The findings suggest the need for a policy framework involving the stakeholders, financing and standardised technologies. To make a change it is proposed to introduce a national, integrated policy incorporating financing and energy governance. - Highlights: ► Households in Sri Lanka lack access to modern energy technology options for cooking. ► Cooking with fuel wood and residues is the norm in Sri Lanka, particularly in rural households. ► A survey of rural households revealed that most cannot afford to switch to cleaner cooking options. ► Most households have little awareness of the health impacts of biomass cooking. ► Women in regular formal employment are more likely to value cleaner cooking options that save time.

Exergetic Aspects of Hydrogen Energy Systems—The Case Study of a Fuel Cell Bus

Directory of Open Access Journals (Sweden)

Evanthia A. Nanaki

2017-02-01

Full Text Available Electrifying transportation is a promising approach to alleviate climate change issues arising from increased emissions. This study examines a system for the production of hydrogen using renewable energy sources as well as its use in buses. The electricity requirements for the production of hydrogen through the electrolysis of water, are covered by renewable energy sources. Fuel cells are being used to utilize hydrogen to power the bus. Exergy analysis for the system is carried out. Based on a steady-state model of the processes, exergy efficiencies are calculated for all subsystems. The subsystems with the highest proportion of irreversibility are identified and compared. It is shown that PV panel has exergetic efficiency of 12.74%, wind turbine of 45%, electrolysis of 67%, and fuel cells of 40%.

Pilot testing of environment-friendly low-emission alternative drive components for city buses. Phase 1. Technical final report

International Nuclear Information System (INIS)

Doemeland, H.; Haase, G.; Sarnes, J.; Schultheis, S.; Schuenemann, M.; Strauss, A.; Voss, K.; Aepler, E.; Stachel, K.; Wolter, M.; Lenz, W.

1993-05-01

The report describes pilot tests of environment-friendly, low-emission city buses with alternative drive systems. The following problems are discussed: Natural gas as primary energy source, natural gas drives, safety requirements, measurement and testing technology for natural gas engines, environmental effects, operating concepts, operating cost. (HW) [de

Load demand profile for a large charging station of a fleet of all-electric plug-in buses

Directory of Open Access Journals (Sweden)

Mario A. Rios

2014-08-01

Full Text Available This study proposes a general procedure to compute the load demand profile from a parking lot where a fleet of buses with electric propulsion mechanisms are charged. Such procedure is divided in three different stages, the first one models the daily energy utilisation of the batteries based on Monte Carlo simulations and route characteristics. The second one models the process in the charging station based on discrete event simulation of queues of buses served by a lot of available chargers. The third step computes the final demand profile in the parking lot because of the charging process based on the power consumption of batteries’ chargers and the utilisation of the available charges. The proposed procedure allows the computation of the number of required batteries’ chargers to be installed in a charging station placed at a parking lot in order to satisfy and ensure the operation of the fleet, the computation of the power demand profile and the peak load and the computation of the general characteristics of electrical infrastructure to supply the power to the station.

Ways to improve the environmental conditions of their buses in operation on passenger routes of cities

Directory of Open Access Journals (Sweden)

Melnychuk S.V.

2017-04-01

Full Text Available The results of studies on operational and environmental parameters buses used on bus routes Zhitomir city. It uses statistical methods for determining the intensity of traffic, passenger traffic and ecology in traffic. To assess the environmental chosen stop with the greatest intensity of traffic, which is the probability of accumulation of pollution transport emissions that exceed permissible limits. Calculation of environmental pollution emission route for vehicles made stops street «Str. Hundreds of Heaven» «CUM», «vul. Hlibna» on the main trunk street Kievska. Results obtained environmental field experiments compared with the data defined calculation methods, based on the proposed use appropriate operational vehicles. The conclusions that indicate the seriousness of the problem and the urgency to address it. The system of environmental safety and road safety in Zhitomir requires significant improvements due to the increased quantities bus vehicles plying city routes. Recommendations to improve the ecological condition of intersections can be developed through the optimization of traffic using buses with environmentally improved operating parameters. Keywords: environmental and operational parameters; ecological safety; environmental assessment; intensity of traffic; passenger traffic; environmental conditions; operation; bus choice; stop.

Txatarra: vivienda transitoria con buses de transporte público

Directory of Open Access Journals (Sweden)

Juan Pablo Arenas Vargas

2011-07-01

Full Text Available El presente análisis del proyecto Casa Linda parte de una exploración conceptual en torno a un hábitat sostenible, mediante la generación de un tipo de vivienda transitoria que reutiliza buses de transporte público destinados a ser reducidos a chatarra. La necesidad de replantear la labor de configurar espacios con materiales y formas predeterminados llevó a los autores a comprender cómo resultan insuficientes los medios tradicionales de construcción, en los que se acostumbra emplear materias primas en presentaciones estandarizadas y con acabados predefinidos que se adaptan a los requerimientos y necesidades del proyecto. Enfrentar el proyecto a partir del reciclaje de materiales y objetos (chatarra, de diversas dimensiones y en variadas condiciones, generó un proceso cuya característica principal es la imposibilidad de anticipar con exactitud los procesos constructivos y los acabados finales.

Fuel consumption and exhaust emissions of urban buses. Performance of newest diesel technology; Kaupunkibussien polttoaineenkulutus ja pakokaasupaeaestoet. Uusimman dieseltekniikan suorituskyky

Energy Technology Data Exchange (ETDEWEB)

Nylund, N.O.; Erkkilae, K.; Hartikka, T.

2007-03-15

The research was carried out by the Finnish Public Transport Association. Altogether seven vehicles were measured, two two-axle Euro 3 -class vehicles as references (Scania and Volvo), three new Euro 4 -class vehicles (Mercedes-Benz, Scania and Volvo) and two new three-axle vehicles (Euro 4 Scania and Euro 5 Volvo). The measurements were carried out on a chassis dynamometer, using three cycles describing actual driving. In addition to fuel consumption, exhaust emissions were also recorded for these vehicles. The differences in fuel consumption and operating expenses were after all smaller than first anticipated. When it comes to the Euro 3 -class reference vehicles, Volvo consumes 7.10% more fuel than Scania. For new two-axle vehicles the difference in fuel consumption, when simulating urban driving, is only 3.4%. Due to different technical solutions, the results were anticipated to be greater. In suburban driving although, the difference is at its most 11%. The Volvo Euro 4 -bus has in average the lowest fuel consumption. Looking at the three-axle vehicles, Scania consumes 3.5% less fuel than does Volvo. The measurements do not give an unambiguous answer to whether the EGR- or SCR technology is preferable regarding fuel consumption. The contemplation is hindered by two factors. On one hand, the order of superiority depends on the driving cycle, on the other, the actual exhaust emissions do not match with expectations. Scania's Euro 4 -engines produce higher NO{sub x}-emissions than its Euro 3 -engine. The fuel efficient Volvo Euro 4 -engine is not truly Euro 4 -class what comes to NO{sub x}-emissions. The Mercedes- Benz Euro 4- and Volvo Euro 5 -engines produce NO{sub x}-emissions genuinely matching their classes. Both fuel consumption and exhaust emissions have been observed in the study. In case exhaust emissions were completely disregarded, fleet decisions might be directed towards fuel efficient vehicles which after all do not reach the level of emission

Analysis of production models and hydrogen supply for urban collective transportation buses: a case study at Foz do Iguacu; Analise de modelos de producao e abastecimento de hidrogenio para onibus de transporte coletivo urbano: estudo de caso em Foz do Iguacu

Energy Technology Data Exchange (ETDEWEB)

Riveros-Godoy, Gustavo [Universidade Nacional de Assuncao (Paraguay). Faculdade de Ciencias Quimicas]. E-mail: riveros@qui.una.py; Cavaliero, Carla; Peres, Ennio [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica

2008-07-01

Even though technical-economical barriers still exist for the development of an economy based in the hydrogen, these difficulties are opportunities for the appearance of new business of goods and services, energetic matrix diversification, focusing of researches activities, development and support to provide sustainability to the new economy. This study presents the technical-economical comparison of hydrogen production and supply models, using the so-called Spilled Turbinable Energy of the Itaipu Hydroelectric Power Plant and available for the transport sector. The substitution of the urban collective diesel bus fleet with fuel cell buses in Foz do Iguacu city was used as a case study in this work. (author)

Transition? What transition? : Changing energy systems in an increasingly carbon constrained world

NARCIS (Netherlands)

Mc Cahery, J.A.; Lopez de Silanes, Florencio; de Roode, Alexander

2014-01-01

Energy transitions have been taking place continuously since the Industrial Revolution. These transitions primarily involve national energy mixes. In general, countries keep moving up the energy ladder, meaning that they integrate larger and larger proportions of specialized fuels into their energy

The introduction of gas-powered busses in Berne; Die Einfuehrung von Gasbussen bei Bernmobil - Ein Erfahrungsbericht

Energy Technology Data Exchange (ETDEWEB)

Finger, D.; Kljun, N.; Keller, M.

2008-07-01

This report for the Swiss Federal Office of Energy (SFOE) discusses the experience gained from the operation of biogas-powered buses in Berne, Switzerland. The fleet conversion from diesel-engined buses to new vehicles powered by biogas from the city's wastewater treatment plant is discussed. Six operational aspects involved in the use of gas-powered buses in comparison with traditional diesel buses are examined and discussed. These include infrastructure adaptations, fuel and energy consumption, emissions and air-hygiene, operational changes, financial aspects and acceptance of the new vehicles both by operating personnel and the general public. Operational difficulties encountered after fire-damage to the gas filling equipment in the bus depot are noted. Fuel consumption is commented on and measurements made on emissions are discussed. The advantages and disadvantages of biogas busses in comparison with diesel busses are discussed.

Crash problem definition and safety benefits methodology for stability control for single-unit medium and heavy trucks and large-platform buses

Science.gov (United States)

2009-10-01

This report presents the findings of a comprehensive engineering analysis of electronic stability control (ESC) and roll stability control (RSC) systems for single-unit medium and heavy trucks and large-platform buses. This report details the applica...

Solar Electricity and Solar Fuels: Status and Perspectives in the Context of the Energy Transition.

Science.gov (United States)

Armaroli, Nicola; Balzani, Vincenzo

2016-01-04

The energy transition from fossil fuels to renewables is already ongoing, but it will be a long and difficult process because the energy system is a gigantic and complex machine. Key renewable energy production data show the remarkable growth of solar electricity technologies and indicate that crystalline silicon photovoltaics (PV) and wind turbines are the workhorses of the first wave of renewable energy deployment on the TW scale around the globe. The other PV alternatives (e.g., copper/indium/gallium/selenide (CIGS) or CdTe), along with other less mature options, are critically analyzed. As far as fuels are concerned, the situation is significantly more complex because making chemicals with sunshine is far more complicated than generating electric current. The prime solar artificial fuel is molecular hydrogen, which is characterized by an excellent combination of chemical and physical properties. The routes to make it from solar energy (photoelectrochemical cells (PEC), dye-sensitized photoelectrochemical cells (DSPEC), PV electrolyzers) and then synthetic liquid fuels are presented, with discussion on economic aspects. The interconversion between electricity and hydrogen, two energy carriers directly produced by sunlight, will be a key tool to distribute renewable energies with the highest flexibility. The discussion takes into account two concepts that are often overlooked: the energy return on investment (EROI) and the limited availability of natural resources-particularly minerals-which are needed to manufacture energy converters and storage devices on a multi-TW scale. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Intermediate transport in Southeast Asia. [Carts, cycles, mini-buses

Energy Technology Data Exchange (ETDEWEB)

Meier, A.K.

1977-06-01

Traffic flows through the streets of Southeast Asian countries even though they are used for almost all aspects of human and animal existence. The carts, bicycles, tricycles, and motorcycles, motorized three-wheelers, mini-buses are the so-called intermediate-transport vehicles. It is upon this group of vehicles that a culture--constrained by its own unique economic, environmental, and technological factors--exerts its influence most directly toward the solution of the transport problem. Transportation fills more service roles in Southeast Asian cities than in Western cities. Communication facilities such as telephones and postal services are notoriously unreliable. The personal encounter is all important in social and business interactions in Southeast Asia. Each of the transport modes is examined in view of design and use in a number of specific cultural settings for the countries in Southeast Asia. Present use of intermediate transport in developed countries is discussed briefly, and its further development predicted--pointing out the health and conservation advantages. (MCW)

Fuel consumption from vehicles of China until 2030 in energy scenarios

International Nuclear Information System (INIS)

Zhang Qingyu; Tian Weili; Zheng Yingyue; Zhang Lili

2010-01-01

Estimation of fuel (gasoline and diesel) consumption for vehicles in China under different long-term energy policy scenarios is presented here. The fuel economy of different vehicle types is subject to variation of government regulations; hence the fuel consumption of passenger cars (PCs), light trucks (Lts), heavy trucks (Hts), buses and motor cycles (MCs) are calculated with respect to (i) the number of vehicles, (ii) distance traveled, and (iii) fuel economy. On the other hand, the consumption rate of alternative energy sources (i.e. ethanol, methanol, biomass-diesel and CNG) is not evaluated here. The number of vehicles is evaluated using the economic elastic coefficient method, relating to per capita gross domestic product (GDP) from 1997 to 2007. The Long-range Energy Alternatives Planning (LEAP) system software is employed to develop a simple model to project fuel consumption in China until 2030 under these scenarios. Three energy consumption decrease scenarios are designed to estimate the reduction of fuel consumption: (i) 'business as usual' (BAU); (ii) 'advanced fuel economy' (AFE); and (iii) 'alternative energy replacement' (AER). It is shown that fuel consumption is predicted to reach 992.28 Mtoe (million tons oil equivalent) with the BAU scenario by 2030. In the AFE and AER scenarios, fuel consumption is predicted to be 734.68 and 600.36 Mtoe, respectively, by 2030. In the AER scenario, fuel consumption in 2030 will be reduced by 391.92 (39.50%) and 134.29 (18.28%) Mtoe in comparison to the BAU and AFE scenarios, respectively. In conclusion, our models indicate that the energy conservation policies introduced by governmental institutions are potentially viable, as long as they are effectively implemented.

Technical evaluation report on the 120 Vac vital instrument buses and inverter Technical Specifications Issue B71

International Nuclear Information System (INIS)

St Leger-Barter, G.; White, R.L.

1982-01-01

The operation of a Pressurized Water Reactor (PWR) with one of its 120 Vac vital buses energized in an off-normal mode was analyzed. A Probabilistic Risk Assessment was made to determine the increment of risk by energizing a vital bus from an off-site source directly vs energizing it from its normal, uninterruptible source (i.e., a battery/inverter arrangement). The calculations were made based on uninterruptible source energized vital buses as the normal mode. The analysis indicated that a reduction in the incremental risk increase (caused by plant operation with a vital bus being energized in an off-normal mode) can be accomplished by limiting the time permitted in that condition. Currently, the time that a vital bus can be energized in the off-normal mode is not universally time-limited by plant Technical Specifications. Several alternatives for the reduction in incremental risk were examined and their value/impacts were derived. These data indicate that a recommendation be made for a Technical Specification time limitation of 72 hours per year for off-normal energizing a vital bus during operation of a PWR

Compressed natural gas (CNG) in fueled systems and the significance of CNG in vehicular transportation

Energy Technology Data Exchange (ETDEWEB)

Ayar, G. [Besikduzu, Trabzon (Turkey)

2006-05-15

Most NG vehicles operate using compressed natural gas (CNG). CNG's popularity stems, in part, from its clean-burning properties. In addition, more than 85,000 CNG vehicles, including one out of every five transit buses, are operating successfully today. This compressed gas is stored in similar fashion to a car's gasoline tank, attached to the rear, top, or undercarriage of the vehicle in a tube-shaped storage tank. A CNG tank can be filled in a similar manner, and in a similar amount of time, to a gasoline tank. (author)

Transition strategy of the transportation energy and powertrain in China

International Nuclear Information System (INIS)

Wang Hewu; Ouyang Minggao

2007-01-01

The problems of the transportation energy and environment are the major challenges faced globally in the 21st century and are especially serious for China. The future 20 years is the strategic opportunity period of the transition of the transportation energy and powertrain system for China. The greatest characteristics of hydrogen economy lie in its diversity of the primary energy source, the unification of energy carrier and the greening of energy transformation. Development of hydrogen energy transportation powertrain system is suitable for China from the views of the situation of Chinese resources and energy sources, the urban and rural layouts, the superiority of later development and the successful practices of clean cars and electric vehicle development projects. The transition of the transportation energy powertrain system includes three parts: the transition of the energy structure, the transition of the powertrain system and the transition of the fuel infrastructure. The technical pathways of energy powertrain system transition includes expending the use of gaseous fuel to prompt the multiform of the transportation energy and to prepare for the transition of the infrastructure simultaneously, developing and promoting the hybrid technology to solve the current energy and environment problems and to prepare for the transition of powertrain system, and focusing on the research and development and demonstration of fuel cell vehicles and the hydrogen energy technology to prompt the earlier formation of the market of fuel cell vehicles. The goal in the near and medium term of transition is to reduce the fuel consumption by 100 million ton in 2020 by substituting and saving, and the long-term goal is to setup the infrastructure of hydrogen and fuel cell vehicle as the main one replacing the petroleum internal combustion engine vehicle. In order to realize the strategic goals of the transition, the four-phases strategic periods and research and development

Fuelling clean air : municipal fuel purchasing policies that reduce emissions contributing to poor air quality and climate change

International Nuclear Information System (INIS)

Perrotta, K.

2003-03-01

Air quality can be improved by low sulphur fuels in two ways: through the direct reduction of sulphates, sulphur dioxide and PM; and by improving the effectiveness of existing emission control devices. This report examined three case studies involving the fuel purchasing policies in three Ontario municipalities: Toronto, Waterloo, and Brampton. Toronto favors purchasing conventional fuels with lower sulphur levels. Waterloo will purchase on-road diesel for its off-road diesel fleet; ultra low sulphur diesel (ULSD) for buses; and 10 per cent ethanol blended with 90 per cent gasoline (E10) for its gasoline-fuelled fleet. Brampton purchased 20 per cent biodiesel blended with 80 per cent on-road diesel (B20). Two approaches were examined for lowering emissions from gasoline fuelled vehicles: favouring gasoline with the lowest sulphur levels, and purchasing E10. It was recommended that the Greater Toronto Area (GTA) Clean Air Council look into: ownership of emissions trading credits created as a result of fuel purchasing policies; the benefits of, and mechanisms available for, pooling fuel purchases; and, establishing a subcommittee to monitor developments related to fuels, vehicles and emission control technologies. 48 refs., 18 tabs

Chapter 3: Simulating fire hazard across landscapes through time: integrating state-and-transition models with the Fuel Characteristic Classification System

Science.gov (United States)

Jessica E. Halofsky; Stephanie K. Hart; Miles A. Hemstrom; Joshua S. Halofsky; Morris C. Johnson

2014-01-01

Information on the effects of management activities such as fuel reduction treatments and of processes such as vegetation growth and disturbance on fire hazard can help land managers prioritize treatments across a landscape to best meet management goals. State-and-transition models (STMs) allow landscape-scale simulations that incorporate effects of succession,...

Exhaust emissions evaluation of Colombian commercial diesel fuels

International Nuclear Information System (INIS)

Torres, Jaime; Bello, Arcesio; Sarmiento, Jose; Rostkowski, Jacek; Brady, Jeremy

2003-01-01

Ecopetrol, based on the results obtained in the study, The effect of diesel properties on the emissions of particulate matter (Bello et al 2000), reformulated the diesel fuel distributed in Bogota, becoming it lighter and with lower sulfur content. In order to evaluate the environmental benefits that the reformulation of diesel fuel generate in Bogota, Instituto Colombiano del Petroleo (ICP), with the assistance of emissions research and measurement division (ERMD) from environment Canada, arranged a research project to determine the changes in CO, THC, NO x , CO 2 and particulate matter emissions. The research program was developed in two steps. First one, developed in Bogota, involved a fleet test with 15 public service buses that normally operate in Bogota's savannah, using a portable emissions sampling technology developed for ERMD (DOES2) and following a representative transient driving cycle. Second step, carried out in ERMD's Heavy-Duty engine emissions laboratory in Ottawa, tested a 1995 caterpillar 3406E 324/5 KW (435 HP) diesel truck engine on the same samples of Colombian diesel fuels used in the fleet tests performed in Bogota, baselining the tests with a Canadian commercial low sulfur diesel fuel. The two commercial Colombian diesel fuels used had the following properties: High Sulfur Diesel (HSD), with 3000 ppm (0,3 wt %) of sulfur and a final boiling point (FBP) of 633 K and the new reformulated diesel fuel, with 1000 ppm (0,1 wt %) of sulfur and FBP of 613 K, which is currently been distributed in Bogota. Fleet test show small reduction on CO, THC and TPM, and small increments on CO 2 and NO x but with not statistically significant results, while engine testing shows a strong reduction of 40/8% in TPM when you use the new reformulated diesel fuel (0,1 wt % of sulfur) instead of high sulfur diesel

Transition to a post-carbon society: Linking environmental justice and just transition discourses

International Nuclear Information System (INIS)

Evans, Geoff; Phelan, Liam

2016-01-01

The Hunter Valley, in New South Wales, Australia, is a globally significant coal mining and exporting region. The Hunter economy's strong basis in fossil fuel production and consumption is challenged by civil society campaigns employing environmental justice discourses. This paper analyses how two civil society campaigns in the Hunter region (‘Stop T4′ and 'Groundswell’) have countered the regional hegemony of fossil fuel interests from an environmental justice perspective. However, the discursive dominance of the 'jobs versus environment’ frame hinders efforts to build solidarity amongst local environmental justice goals on the one hand, and workers and union aspirations for secure, quality jobs on the other. Long-term structural decline of global coal markets adds pressure for economic transition. We argue that campaigns to open up possibilities for transition away from fossil fuel dependency to a post-carbon society can be strengthened by engaging with the 'just transition’ discourses that are typically associated with organised labour. Doing so can create synergy for social change by aligning community and labour movement interests. Inclusive social movement partnerships around this synergy must address structural disadvantage that creates social and economic insecurity if communities are to prevail over the fossil fuel sector's hegemony. - Highlights: • Jobs versus environment. • Environmental justice. • Just transition. • Counter-hegemonic forces.

Alternative Fuels Data Center: New Hampshire Transportation Data for

Science.gov (United States)

Private Biodiesel (B20 and above) 1 3 Compressed Natural Gas (CNG) 3 1 Electric 80 20 Ethanol (E85) 0 0 YouTube Video thumbnail for New Hampshire Cleans up with Biodiesel Buses New Hampshire Cleans up with Biodiesel Buses May 26, 2017 https://www.youtube.com/embed/9Qq-Leiujjk Video thumbnail for New Hampshire

Nuclear Energy R and D Imperative 3: Enable a Transition Away from Fossil Fuel in the Transportation and Industrial Sectors

International Nuclear Information System (INIS)

Petti, David; Herring, J. Stephen

2010-01-01

As described in the Department of Energy Office of Nuclear Energy's Nuclear Energy R and D Roadmap, nuclear energy can play a significant role in supplying energy for a growing economy while reducing both our dependence on foreign energy supplies and emissions from the burning of fossil fuels. The industrial and transportation sectors are responsible for more than half of the greenhouse gas emissions in the U.S., and imported oil supplies 70% of the energy used in the transportation sector. It is therefore important to examine the various ways nuclear energy can facilitate a transition away from fossil fuels to secure environmentally sustainable production and use of energy in the transportation and manufacturing industry sectors. Imperative 3 of the Nuclear Energy R and D Roadmap, entitled 'Enable a Transition Away from Fossil Fuels by Producing Process Heat for use in the Transportation and Industrial Sectors', addresses this need. This document presents an Implementation Plan for R and D efforts related to this imperative. The expanded use of nuclear energy beyond the electrical grid will contribute significantly to overcoming the three inter-linked energy challenges facing U.S. industry: the rising and volatile prices for premium fossil fuels such as oil and natural gas, dependence on foreign sources for these fuels, and the risks of climate change resulting from carbon emissions. Nuclear energy could be used in the industrial and transportation sectors to: (1) Generate high temperature process heat and electricity to serve industrial needs including the production of chemical feedstocks for use in manufacturing premium fuels and fertilizer products, (2) Produce hydrogen for industrial processes and transportation fuels, and (3) Provide clean water for human consumption by desalination and promote wastewater treatment using low-grade nuclear heat as a useful additional benefit. Opening new avenues for nuclear energy will significantly enhance our nation

Evaluation Of Oxide And Silicide Mixed Fuels Of The RSG-GAS Core

International Nuclear Information System (INIS)

Tukiran; Sembiring, Tagor Malem; Suparlina, Lily

2000-01-01

Fuel exchange of the RSG-GAS reactor core from uranium oxide to uranium silicide in the same loading, density, and enrichment, that is 250 gr, 2.98 gr/cm 3 , and 19.75%, respectively, will be performed in-step wise. In every cycle of exchange with 5/1 mode, it is needed to evaluate the parameter of reactor core operation. The parameters of the reactor operation observed are criticality mass of fuels, reactivity balance, and fuel reactivity that give effect to the reactor operation. The evaluation was done at beginning of cycle of the first and second transition core with compared between experiment and calculation results. The experiments were performed at transition core I and II, BOC, and low power. At transition core I, there are 2 silicide fuels (RI-224 and R1-225) in the core and then, added five silicide fuels (R1-226, R1-252, R1-263, and R1-264) to the core, so that there are seven silicide fuels in the transition core II. The evaluation was done based on the experiment of criticality, control rod calibration, fuel reactivity of the RSG-GAS transition core. For inserting 2 silicide fuels in the transition core I dan 7 fuels in the transition core II, the operation of RSG-GAS core fulfilled the safety margin and the parameter of reactor operation change is not occur drastically in experiment and calculation results. So that, the reactor was operated during 36 days at 15 MW, 540 MWD at the first transition core. The general result showed that the parameter of reactor operation change is small so that the fuel exchange from uranium oxide to uranium silicide in the next step can be done

National fuel cell bus program : proterra fuel cell hybrid bus report, Columbia demonstration.

Science.gov (United States)

2011-10-01

This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by the Center for Transportation and the Environment an...

Flexible fuel cycle initiative for the transition period from current reactors to next generation reactors

International Nuclear Information System (INIS)

Yamashita, Junichi; Fukasawa, Tetsuo; Hoshino, Kuniyoshi; Kawamura, Fumio; Shiina, Kouji; Sasahira, Akira

2005-01-01

A sustainable electricity supply by fast breeder reactors (FBRs) is essential to ensure energy security and prevent global warming. Transition from light water reactors (LWRs) to FBRs and establishment of an FBR cycle are indispensable, which requires plutonium (Pu) for the introduction of FBRs. The authors propose advanced system called 'Flexible Fuel Cycle Initiative (FFCI)' which can respond flexibly the future expected technical and social uncertainties, can hold no surplus Pu, and can achieve an economical FBR cycle. In the new concept of FFCI, 2nd LWR reprocessing which would succeed Rokkasho Reprocessing Plant is a simple facility to carry out only uranium (U) removal and residual 'recycle material' is stored or utilized. According to FBRs introduction status, recycle material is immediately treated in an FBR reprocessing to fabricate FBR fuel or temporarily stored for the utilization in FBRs at necessary timing. FFCI has high flexibility by having several options for future uncertainties by the introduction of recycle material as a buffer material between LWR and FBR cycles. (author)

Development of boiling transition analysis code TCAPE-INS/B based on mechanistic methods for BWR fuel bundles. Models and validations with boiling transition experimental data

International Nuclear Information System (INIS)

Ishida, Naoyuki; Utsuno, Hideaki; Kasahara, Fumio

2003-01-01

The Boiling Transition (BT) analysis code TCAPE-INS/B based on the mechanistic methods coupled with subchannel analysis has been developed for the evaluation of the integrity of Boiling Water Reactor (BWR) fuel rod bundles under abnormal operations. Objective of the development is the evaluation of the BT without using empirical BT and rewetting correlations needed for different bundle designs in the current analysis methods. TCAPE-INS/B consisted mainly of the drift-flux model, the film flow model, the cross-flow model, the thermal conductivity model and the heat transfer correlations. These models were validated systematically with the experimental data. The accuracy of the prediction for the steady-state Critical Heat Flux (CHF) and the transient temperature of the fuel rod surface after the occurrence of BT were evaluated on the validations. The calculations for the experiments with the single tube and bundles were carried out for the validations of the models incorporated in the code. The results showed that the steady-state CHF was predicted within about 6% average error. In the transient calculations, BT timing and temperature of the fuel rod surface gradient agreed well with experimental results, but rewetting was predicted lately. So, modeling of heat transfer phenomena during post-BT is under modification. (author)

Evaluation of Particle Counter Technology for Detection of Fuel Contamination Detection Utilizing Fuel System Supply Point

Science.gov (United States)

2014-06-19

product used as a diesel product for ground use (1). Free water contamination (droplets) may appear as fine droplets or slugs of water in the fuel...methods and test procedures for the calibration and use of automatic particle counters. The transition of this technology to the fuel industry is...UNCLASSIFIED 6 UNCLASSIFIED Receipt Vehicle Fuel Tank Fuel Injector Aviation Fuel DEF (AUST) 5695B 18/16/13 Parker 18

The role of transportation technologies in reducing greenhouse gas emissions

International Nuclear Information System (INIS)

Anon.

1995-11-01

The potential role of passenger transportation technologies in reducing greenhouse gas emissions was discussed. The technologies considered in the report were those that affect ground transportation of passengers and were in at least the early stages of development in 1995. They were: (1) technologies to improve the fuel efficiency of cars and light trucks, (2) alternative fuels for internal combustion engines, (3) electric hybrid vehicles, (4) advanced technology transit buses, (5) intelligent transportation systems, (6) high speed rail, and (7) bicycles. For each option, the advantages and disadvantages were described. The feasibility of establishing a high-speed rail system serving Canada's most densely populated region, the Windsor to Quebec City corridor, was discussed. Economic and environmental studies of such a proposal are underway. tabs

Emergency and Disaster Preparedness of School Transportation Staff and School Buses in the United States: Compliance With Recommendations for School Transportation Safety.

Science.gov (United States)

Olympia, Robert P; Weber, Christopher; Brady, Jodi; Ho, Susana

2017-11-01

The aim of the study was to determine the compliance of school transportation staff and school buses with recommendations for the safe transportation of children to and from school and school-related activities. An electronic questionnaire was distributed to school transportation staff represented by the International Brotherhood of Teamsters during the 2013-2014 academic year. Analysis was performed on 558 completed questionnaires (13% usable response rate). Responders had previous training in first aid (89%), basic life support (28%), and cardiopulmonary resuscitation (52%). Seventy-eight percent of school buses in our sample had restraint devices and 87% had seat belt cutters. Responders reported the immediate availability of the following on their bus: communication devices (81%), first aid kits (97%), fire extinguishers (89%), automated external defibrillators (1%), and epinephrine autoinjectors (2%). Thirty percent of responders have had no previous training in the management of emergencies such as trouble breathing, severe allergic reaction, seizures, cardiac arrest or unresponsiveness, and head, neck, or extremity trauma. Thirteen percent of responders are unfamiliar with or have had no previous training on protocols regarding emergency shelters and community evacuation plans in the event of a disaster. Variability exists in the compliance of school transportation staff and school buses with recommendations for the safe transportation of children. Areas for improvement were identified, such as educating school transportation staff in the recognition and initial management of pediatric emergencies, ensuring the presence of restraint devices, increasing the immediate availability of certain emergency medications and equipment, and familiarizing school transportation staff with designated emergency shelters and community evacuation plans.

Dynamic Simulations of Advanced Fuel Cycles

International Nuclear Information System (INIS)

Piet, Steven J.; Dixon, Brent W.; Jacobson, Jacob J.; Matthern, Gretchen E.; Shropshire, David E.

2011-01-01

Years of performing dynamic simulations of advanced nuclear fuel cycle options provide insights into how they could work and how one might transition from the current once-through fuel cycle. This paper summarizes those insights from the context of the 2005 objectives and goals of the U.S. Advanced Fuel Cycle Initiative (AFCI). Our intent is not to compare options, assess options versus those objectives and goals, nor recommend changes to those objectives and goals. Rather, we organize what we have learned from dynamic simulations in the context of the AFCI objectives for waste management, proliferation resistance, uranium utilization, and economics. Thus, we do not merely describe 'lessons learned' from dynamic simulations but attempt to answer the 'so what' question by using this context. The analyses have been performed using the Verifiable Fuel Cycle Simulation of Nuclear Fuel Cycle Dynamics (VISION). We observe that the 2005 objectives and goals do not address many of the inherently dynamic discriminators among advanced fuel cycle options and transitions thereof.

Optimizing Performance of at-grade Intersection with Bus Rapid Transit Corridor and Heterogeneous Traffic

Directory of Open Access Journals (Sweden)

Hemant Kumar Sharma

2012-06-01

Full Text Available Bus Rapid Transit (BRT has emerged as a preferred mode of public transport in various countries all over the world for its cost effectiveness in construction as well as in operation and maintenance. The rapid transit feature of BRT is seen as a solution to many traffic problems in these countries. However, in developing countries like India, the right -of-way for most of the roads is restricted and traffic is heterogeneous in nature. Provision of BRT in existing right -of-way reduces the capacity available for other motorized traffic. As the buses travel with a certain frequency on dedicated bus- ways, the dedicated corridor remains unused for most of the period when other traffic on motorized vehicle (MV lanes suffers from congestion. The problem gets severe at intersections. However, if buses are operated in mixed traffic it is no more rapid transit. Hence, a solution is required to address this problem and optimize the performance of traffic as a whole. This paper presents the effect if dedicated bus-ways end at a reasonable distance before the stop line at a busy signalized at-grade intersection, and bus lanes (beyond that are made available to all the motorized vehicular traffic (heterogeneous traffic at intersection. The performance evaluation is done in terms of average queue length, maximum queue length, average delay time per vehicle, vehicle throughput, average speed in network and emission of Carbon monoxide CO, mono-nitrogen oxides NOx and Volatile organic compounds (VOC. It is observed that availability of bus lanes to other motorized traffic for a reasonable distance before intersection considerably reduces the average queue length, maximum queue length, average delay time per vehicle and emission per vehicle, while there is an increase in vehicle throughput and average speed of all the vehicles in the network. Thus it results in reduction of congestion and performance enhancement of at-grade intersections and network. Results of

H/CNG pathway to hydrogen

International Nuclear Information System (INIS)

Bugyra, W.J.; Martin, D.R.

2004-01-01

'Full text:' The addition of hydrogen to natural gas to produce a 'premium' fuel offers an ideal bridge to the hydrogen and fuel cell era. This pathway provides many of the expected benefits of hydrogen and fuel cells, reduces cost and risk, and facilitates the transition to hydrogen incrementally through existing infrastructure, technologies and channels. The H/CNG pathway is evaluated qualitatively and quantitatively in the context of: barriers to introducing hydrogen infrastructure and how they can be addressed; potential benefits (emissions, energy security) and drawbacks (range, technical compatibility) of H/CNG blended fuels; economics; and, comparative analysis to the use of ethanol in gasoline. Leveraging the NGV industry eases the transition to fuel cells by taking advantage of existing infrastructure, technologies, skills, codes and standards, and provides for incremental change that may be more acceptable to consumers, regulators and incumbent technology providers. The greatest benefits can be achieved through a two-track pathway. One would utilize small amounts of hydrogen in existing NGVs and installed power systems - much as ethanol is added to gasoline. The second introduce products designed specifically to operate on higher levels of H/CNG, like buses, in concentrations where the greatest emission benefits can be achieved. (author)

Road Safety Data, Collection, Transfer and Analysis DaCoTa. Factsheet Traffic safety basic facts 2010 : heavy goods vehicles and buses.

NARCIS (Netherlands)

Pace, J.-F. López de Cozar, E. Pérez-Fuster, P. Sanmartín, J. Kirk, A. Yannis, G. Evgenikos, P. Argyropoulou, E. Papantoniou, P. Broughton, J. Knowles, J. Brandstaetter, C. Candappa, N. Christoph, M. Vis, M. Haddak, M. & Moutengou, E.

2012-01-01

Heavy Goods Vehicles (HGVs) are defined as goods vehicles of over 3,5 tons maximum permissible gross vehicle weight. Road traffic accidents involving HGVs tend to be more severe than other accidents because of the great size and mass of these vehicles. Buses and coaches are included in this Basic

A fuel in blue

International Nuclear Information System (INIS)

Kelley, T.

1992-01-01

This paper reports that U.s. police departments are increasingly turning to natural gas for the same reasons other vehicle fleet operators do: It's much cheaper than gasoline and better for the environment - and it saves on engine wear-and-tear, too. Of course, the police have a lot of company in seeing the merits of natural gas vehicles (NGVs). Nineteen ninety-two proved itself a good year for NGVs before it was more than a few weeks old. President George Bush personally drove one outside the White House, the General Services Administration ordered 625 NGVs from Chrysler and General Motors, and both Ford and Chevrolet planned to begin this spring to manufacture a small number of vehicles equipped to run solely on natural gas. School districts are happy with the savings they reap by running school buses on natural gas, and the fuel has been embraced by other fleets ranging from garbage trucks in Brooklyn to jet-towing vehicles at Denver's Stapleton Airport. But police departments are different. A patrol care is not just transportation for an officer, but his or her workplace on wheels. And perhaps because they deal with life-and-death situations, police officers aren't eager to change anything - even a vehicle fuel - that they see as doing the job. If marketing natural gas for fleet use is a popular curriculum for gas companies these days, police forces are the demanding final exam

Savannah River bus project

Energy Technology Data Exchange (ETDEWEB)

Summers, W.A. [Westinghouse Savannah River Co., Aiken, SC (United States)

1998-08-01

The H2Fuel Bus is the world`s first hybrid hydrogen electric transit bus. It was developed through a public/private partnership involving several leading technology and industrial organizations in the Southeast, with primary funding and program management provided by the Department of Energy. The primary goals of the project are to gain valuable information on the technical readiness and economic viability of hydrogen buses and to enhance the public awareness and acceptance of emerging hydrogen technologies. The bus has been operated by the transit agency in Augusta, Georgia since April, 1997. It employs a hybrid IC engine/battery/electric drive system, with onboard hydrogen fuel storage based on the use of metal hydrides. Initial operating results have demonstrated an overall energy efficiency (miles per Btu) of twice that of a similar diesel-fueled bus and an operating range twice that of an all-battery powered electric bus. Tailpipe emissions are negligible, with NOx less than 0.2 ppm. Permitting, liability and insurance issues were addressed on the basis of extensive risk assessment and safety analyses, with the inherent safety characteristic of metal hydride storage playing a major role in minimizing these concerns. Future plans for the bus include continued transit operation and use as a national testbed, with potential modifications to demonstrate other hydrogen technologies, including fuel cells.

Evaluation of nuclear fuel reprocessing strategies. 2. LWR fuel storage, recycle economics and plutonium logistics

International Nuclear Information System (INIS)

Prince, B.E.; Hadley, S.W.

1983-01-01

This is the second of a two-part report intended as a critical review of certain issues involved with closing the Light Water Reactor (LWR) fuel cycle and establishing the basis for future transition to commercial breeder applications. The report is divided into four main sections consisting of (1) a review of the status of the LWR spent fuel management and storage problem; (2) an analysis of the economic incentives for instituting reprocessing and recycle in LWRs; (3) an analysis of the time-dependent aspects of plutonium economic value particularly as related to the LWR-breeder transition; and (4) an analysis of the time-dependent aspects of plutonium requirements and supply relative to this transition

A Low-Carbon-Based Bilevel Optimization Model for Public Transit Network

Directory of Open Access Journals (Sweden)

Xu Sun

2013-01-01

Full Text Available To satisfy the demand of low-carbon transportation, this paper studies the optimization of public transit network based on the concept of low carbon. Taking travel time, operation cost, energy consumption, pollutant emission, and traffic efficiency as the optimization objectives, a bilevel model is proposed in order to maximize the benefits of both travelers and operators and minimize the environmental cost. Then the model is solved with the differential evolution (DE algorithm and applied to a real network of Baoji city. The results show that the model can not only ensure the benefits of travelers and operators, but can also reduce pollutant emission and energy consumption caused by the operations of buses, which reflects the concept of low carbon.

26 CFR 48.4221-8 - Tax-free sales of tires, tubes, and tread rubber used on intercity, local, and school buses.

Science.gov (United States)

2010-04-01

... if the bus has a passenger seating capacity of at least 20 adults and the transportation is available... of a school. Incidental use (deadheading) of the school bus without passengers to or from a point to... used on intercity, local, and school buses. 48.4221-8 Section 48.4221-8 Internal Revenue INTERNAL...

Peel Region TransHelp's experience

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-09-15

TransHelp was founded in the Peel Region of Ontario in 1981 to provide paratransit service to individuals unable to use conventional transit. The TransHelp vehicle fleet consists of 40 buses that make over 220,000 one way trips annually. Each vehicle has a typical life span of between 375,000 and 425,000 km. TransHelp vehicles spend much of their time idling in emissions-sensitive areas, such as outside hospitals. In order to reduce fuel costs, TransHelp adopted the use of propane to fuel its vehicles. However, difficulties were experienced with this technology, particularly on V-10 engines where increased maintenance was a problem. SFI Technologies Inc. provided a solution with their SEQUIN System which allows seamless transitioning between gasoline and propane under all conditions without any operator involvement in fuel selection. The technology favours propane as the fuel of choice and automatically switches between propane and gasoline based on the ideal conditions at the time of operation. The technology has received certification from the Environmental Protection Agency in the United States and the Canadian Standards Association. The use of the SEQUIN System has proven to successful for TransHelp. It has allowed the use of propane to be continued, meaning that vehicle emissions are greatly reduced relative to gasoline or diesel fuelled vehicles. TransHelp has realized a fuel savings of 15-20 per cent over gasoline and receives an additional federal transit rebate of 15 per cent for the conversion cost.

Alternative Fuels in Transportation : Workforce needs and opportunities in support of reducing reliance on petroleum fuels

Science.gov (United States)

2016-01-01

An overreliance on foreign oil and the negative impacts of using petroleum fuels on the worlds climate have prompted energy policies that support the diversification of transport fuels and aggressive work to transition to non-petroleum options. Th...

Optimal sizing of plug-in fuel cell electric vehicles using models of vehicle performance and system cost

International Nuclear Information System (INIS)

Xu, Liangfei; Ouyang, Minggao; Li, Jianqiu; Yang, Fuyuan; Lu, Languang; Hua, Jianfeng

2013-01-01

Highlights: ► An analytical model for vehicle performance and power-train parameters. ► Quantitative relationships between vehicle performance and power-train parameters. ► Optimal sizing rules that help designing an optimal PEM fuel cell power-train. ► An on-road testing showing the performance of the proposed vehicle. -- Abstract: This paper presents an optimal sizing method for plug-in proton exchange membrane (PEM) fuel cell and lithium-ion battery (LIB) powered city buses. We propose a theoretical model describing the relationship between components’ parameters and vehicle performance. Analysis results show that within the working range of the electric motor, the maximal velocity and driving distance are influenced linearly by the parameters of the components, e.g. fuel cell efficiency, fuel cell output power, stored hydrogen mass, vehicle auxiliary power, battery capacity, and battery average resistance. Moreover, accelerating time is also linearly dependant on the abovementioned parameters, except of those of the battery. Next, we attempt to minimize fixed and operating costs by introducing an optimal sizing problem that uses as constraints the requirements on vehicle performance. By solving this problem, we attain several optimal sizing rules. Finally, we use these rules to design a plug-in PEM fuel cell city bus and present performance results obtained by on-road testing.

Elements of nuclear reactor fueling theory

International Nuclear Information System (INIS)

Egan, M.R.

1984-01-01

Starting with a review of the simple batch size effect, a more general theory of nuclear fueling is derived to describe the behaviour and physical requirements of operating cycle sequences and fueling strategies having practical use in fuel management. The generalized theory, based on linear reactivity modeling, is analytical and represents the effects of multiple-stream, multiple-depletion-batch fueling configurations in systems employing arbitrary, non-integer batch size strategies, and containing fuel with variable energy generation rates. Reactor operating cycles and cycle sequences are represented with realistic structure that includes the effects of variable cycle energy production, cycle lengths, end-of-cycle operating extensions and manoeuvering allowances. Results of the analytical theory are first applied to the special case of degenerate equilibrium cycle sequences, yielding several fundamental principles related to the selection of refueling strategy. Numerical evaluations of degenerate equilibrium cycle sequences are then performed for a typical PWR core, and accompanying fuel cycle costs are calculated. The impact of design and operational limits as constraints on the performance mappings for this reactor are also studied with respect to achieving improved cost performance from the once-through fuel cycle. The dynamics of transition cycle sequences are then examined using the generalized theory. Proof of the existence of non-degenerate equilibrium cycle sequences is presented when the mechanics of the fixed reload batch size strategy are developed analytically for transition sequences. Finally, an analysis of the fixed reload enrichment strategy demonstrates the potential for convergence of the transition sequence to a fully degenerate equilibrium sequence. (author)

King County Metro Battery Electric Bus Demonstration: Preliminary Project Results

Energy Technology Data Exchange (ETDEWEB)

2017-05-22

The U.S. Federal Transit Administration (FTA) funds a variety of research projects that support the commercialization of zero-emission bus technology. To evaluate projects funded through these programs, FTA has enlisted the help of the National Renewable Energy Laboratory (NREL) to conduct third-party evaluations of the technologies deployed under the FTA programs. NREL works with the selected agencies to evaluate the performance of the zero-emission buses compared to baseline conventional buses in similar service. The evaluation effort will advance the knowledge base of zero-emission technologies in transit bus applications and provide 'lessons learned' to aid other fleets in incrementally introducing next generation zero-emission buses into their operations. This report provides preliminary performance evaluation results from a demonstration of three zero-emission battery electric buses at King County Metro in King County, Washington. NREL developed this preliminary results report to quickly disseminate evaluation results to stakeholders. Detailed evaluation results will be published in future reports.

Stepwise evolution of fuel assembly design toward a sustainable fuel cycle with hard neutron spectrum light water reactors

International Nuclear Information System (INIS)

Uchikawa, Sadao; Okubo, Tsutomu; Nakano, Yoshihiro

2011-01-01

An advanced LWR with hard neutron spectrum, FLWR, aims at efficient and flexible utilization of nuclear resources by evolving its fuel assembly design keeping the same core configuration. A proposed evolution process of the design toward a sustainable fuel cycle is composed of three stages, the first one based on the LWR fuel cycle infrastructures, the second one for transitioning from the LWR fuel cycle to the FR fuel cycle, and the third one based on the FR fuel cycle infrastructures. For the first stage, a fuel assembly design concept named FLWR/MIX has been developed in which enriched UO 2 fuel rods are arranged in the peripheral region of the assembly, surrounding the MOX fuel rods in the central region. The FLWR/MIX design realizes a breeder type operation under the framework of the LWR-MOX technologies and there experience. A modified FLWR/MIX design with low Pu inventory for the second stage has a potential of high Puf conversion ratio of 1.1 and can contribute to smooth and speedy transition from the LWR fuel cycle to the FR fuel cycle. For the third stage, the FLWR/MIX design is extended into a design with natural UO 2 fuel rods to realize multiple Pu recycling keeping a Puf conversion ratio of around 1.0. (author)

Liquefied Natural Gas for Trucks and Buses

International Nuclear Information System (INIS)

James Wegrzyn; Michael Gurevich

2000-01-01

Liquefied natural gas (LNG) is being developed as a heavy vehicle fuel. The reason for developing LNG is to reduce our dependency on imported oil by eliminating technical and costs barriers associated with its usage. The U.S. Department of Energy (DOE) has a program, currently in its third year, to develop and advance cost-effective technologies for operating and refueling natural gas-fueled heavy vehicles (Class 7-8 trucks). The objectives of the DOE Natural Gas Vehicle Systems Program are to achieve market penetration by reducing vehicle conversion and fuel costs, to increase consumer acceptance by improving the reliability and efficiency, and to improve air quality by reducing tailpipe emissions. One way to reduce fuel costs is to develop new supplies of cheap natural gas. Significant progress is being made towards developing more energy-efficient, low-cost, small-scale natural gas liquefiers for exploiting alternative sources of natural gas such as from landfill and remote gas sites. In particular, the DOE program provides funds for research and development in the areas of; natural gas clean up, LNG production, advanced vehicle onboard storage tanks, improved fuel delivery systems and LNG market strategies. In general, the program seeks to integrate the individual components being developed into complete systems, and then demonstrate the technology to establish technical and economic feasibility. The paper also reviews the importance of cryogenics in designing LNG fuel delivery systems

Analyzing the Relationship Between Bus Pollution Policies and Morbidity Using a Quasi-Experiment

OpenAIRE

Ngo, Nicole S.

2015-01-01

Abstract Transit buses are used by millions of commuters every day, but they emit toxic diesel fumes. In 1988, the U.S. Environmental Protection Agency implemented emission standards for transit buses, which have been continually updated. Yet there is no quantitative evidence of the health benefits from these bus pollution policies due to data constraints and confounding variables. In this study, a quasi-experiment is used to exploit the geographic and temporal variation in emission standards...

Report on Hydrogen Bus Demonstrations Worldwide, 2002-2007.

Science.gov (United States)

2009-03-01

Between 2002 and 2007 more than 20 cities in the United States, Europe, China, Japan and Australia have demonstrated buses powered by fuel cells or hydrogen-fueled internal combustion engines, as well as a variety of fueling and related technologies....

Evaluation of city buses installed diesel particulate filter systems on fleet test; Diesel particulate filter system wo tosaishita rosen bus no soko chosa

Energy Technology Data Exchange (ETDEWEB)

Sudo, H [Japan Automobile Research Institute Inc., Tsukuba (Japan)

1997-10-01

An environmental air quality of suspended particulate matter is insufficient in the big city area. To reduce the particulate matter, improvement of engine and development of the Diesel Particulate Filter (DPF) system are carrying. The purpose of this report is to investigate a possibility of practical use of the city buses installed DPF systems. From March 1995, investigation for practical use of these DPF systems on a route buses was carried in regular service operation of the Tokyo and Yokohama Transportation Bureau. The investigation items are service situation, smoke density and preparation inspection. From the result for 2 years service operation, each DPF systems needed some failure correspondence. but these were not fatal problem on using the DPF system. Then the subject of relative to durability and reliability became clear, and the performance of a low particulate emission DPF system obtained the high value evaluation for users. 9 refs., 4 figs., 2 tabs.

Modelling socio-metabolic transitions: The historical take-off, the acceleration of fossil fuel use, and the 1970s oil price shock - the first trigger of a future decline?

Science.gov (United States)

Wiedenhofer, Dominik; Rovenskaya, Elena; Krausmann, Fridolin; Haas, Willi; Fischer-Kowalski, Marina

2013-04-01

By talking about socio-metabolic transitions, we talk about changes in the energy base of socio-economic systems, leading to fundamental changes in social and environmental relations. This refers to the historical shift from a biomass-based (agrarian) economy to a fossil fuel based (industrial) economy just as much as to a future shift from fossil fuels to renewable energy carriers. In our presentation, • We will first show that this pattern of transition can be identified for most high income industrial countries: the later the transition started, the faster it proceeded, and the turning point to stabilization of metabolic rates in all of them happened in the early 1970ies. Due to the inherent non-linearity of this process, two approaches will be aplied to estimate parameters for the starting point, transition speed and saturation level: firstly a combination of an expontential and a generalized logistic function and secondly a Gompertz function. For both an iterative test procedure is applied to find the global minimum of the residual error for the whole function and all its parameters. This theory-based approach allows us to apply a robust methodology across all cases, thereby yielding results which can be generalized. • Next, we will show that this was not just a "historical" socio-ecological transition, however. Currently, a substantial number of countries comprising more than half of the world's population are following a similar transitional pathway at an ever accelerating pace. Based on empirical data on physical resource use and the above sketched methodology, we can show that these so-called emerging economies are currently in the take-off or acceleration phase of the very same transition. • Apart from these "endogenous" processes of socio-metabolic transition, we will investigate the effect of external shocks and their impact on the dynamics of energy and materials use. The first such shock we will explore is the oil crisis of 1972 that possibly

American fuel cell bus project : first analysis report.

Science.gov (United States)

2013-06-01

This report summarizes the experience and early results from the American Fuel Cell Bus Project, a fuel cell electric bus demonstration : funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by CALST...

Preliminary study on field buses for the control system of the high voltage of the ATLAS hadronic calorimeter; Etude preliminaire d`un reseau de terrain pour le systeme de controle des hautes tensions du calorimetre hadronique d`Atlas

Energy Technology Data Exchange (ETDEWEB)

Drevet, F.; Chadelas, R.; Montarou, G.

1996-12-31

We present here after a preliminary study on field buses for the control system of the high voltage of the photomultipliers of the TILECAL calorimeter. After some generalities, different commercial buses are reviewed (CAN, ARCET, WorldFIP, Profibus and LonWorks). The Profibus and LonWorks solution are more extensively studies as a possible solution for the high voltage system of the TILE hadronic calorimeter. (authors).

Concentration measurement in a road tunnel as a method to assess "real-world" vehicles exhaust emissions

Science.gov (United States)

Zanini, G.; Berico, M.; Monforti, F.; Vitali, L.; Zambonelli, S.; Chiavarini, S.; Georgiadis, T.; Nardino, M.

An experiment aimed at comparing particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) concentrations produced in a road tunnel by buses is described. The experiment took place in 2001 in Bologna when a couple of buses belonging to the public transport fleet where driven backwards and forwards in a road tunnel closed to all other vehicles. Buses run in the tunnel for 8 h a day for 4 experiment days, each day using a different fuel: biodiesel, diesel-water emulsion, diesel-water emulsion with low sulphur content and commercial diesel. Average daily concentrations of PM of different sizes and of 12 PHAs were measured and comparison between different fuels was attempted in order to assess "real-world" exhaust emissions of different fuels. Due to heterogeneity of experimental conditions in different days and the relatively large measurement uncertainties, the effort was only partially successful, and it was not possible to state any firm conclusion on fuels reliability even if some indications in agreement with literature were found. Nevertheless, the experiment and the data analysis method developed could be of interest as a methodological approach for future experiments aimed at evaluating "real-world" exhaust emissions of single vehicles.

School Districts Move to the Head of the Class with Propane

Energy Technology Data Exchange (ETDEWEB)

2016-01-01

Propane has been a proven fuel for buses for decades. For the first time in 2007, Blue Bird rolled out a propane school bus using direct liquid injection, which was later followed by Thomas Built Buses and Navistar. Because this new technology is much more reliable than previous designs, it is essentially reintroducing propane buses to many school districts. During this same time period, vehicle emissions standards have tightened. To meet them, diesel engine manufacturers have added diesel particulate filters (DPF) and, more recently, selective catalytic reduction (SCR) systems. As an alternative to diesel buses with these systems, many school districts have looked to other affordable, clean alternatives, and they've found that propane fits the bill.

Transient fuel melting

International Nuclear Information System (INIS)

Roche, L.; Schmitz, F.

1982-10-01

The observation of micrographic documents from fuel after a CABRI test leads to postulate a specific mode of transient fuel melting during a rapid nuclear power excursion. When reaching the melt threshold, the bands which are characteristic for the solid state are broken statistically over a macroscopic region. The time of maintaining the fuel at the critical enthalpy level between solid and liquid is too short to lead to a phase separation. A significant life-time (approximately 1 second) of this intermediate ''unsolide'' state would have consequences on the variation of physical properties linked to the phase transition solid/liquid: viscosity, specific volume and (for the irradiated fuel) fission gas release [fr

Advanced Nuclear Fuel Cycle Transitions: Optimization, Modeling Choices, and Disruptions

Science.gov (United States)

Carlsen, Robert W.

Many nuclear fuel cycle simulators have evolved over time to help understan the nuclear industry/ecosystem at a macroscopic level. Cyclus is one of th first fuel cycle simulators to accommodate larger-scale analysis with it liberal open-source licensing and first-class Linux support. Cyclus also ha features that uniquely enable investigating the effects of modeling choices o fuel cycle simulators and scenarios. This work is divided into thre experiments focusing on optimization, effects of modeling choices, and fue cycle uncertainty. Effective optimization techniques are developed for automatically determinin desirable facility deployment schedules with Cyclus. A novel method fo mapping optimization variables to deployment schedules is developed. Thi allows relationships between reactor types and scenario constraints to b represented implicitly in the variable definitions enabling the usage o optimizers lacking constraint support. It also prevents wasting computationa resources evaluating infeasible deployment schedules. Deployed power capacit over time and deployment of non-reactor facilities are also included a optimization variables There are many fuel cycle simulators built with different combinations o modeling choices. Comparing results between them is often difficult. Cyclus flexibility allows comparing effects of many such modeling choices. Reacto refueling cycle synchronization and inter-facility competition among othe effects are compared in four cases each using combinations of fleet of individually modeled reactors with 1-month or 3-month time steps. There are noticeable differences in results for the different cases. The larges differences occur during periods of constrained reactor fuel availability This and similar work can help improve the quality of fuel cycle analysi generally There is significant uncertainty associated deploying new nuclear technologie such as time-frames for technology availability and the cost of buildin advanced reactors

Why People Are Not Willing to Let Their Children Ride in Driverless School Buses: A Gender and Nationality Comparison

Directory of Open Access Journals (Sweden)

Emily C. Anania

2018-02-01

Full Text Available As driverless vehicles proliferate, it is possible that this technology will be applied in mass transport vehicles. School buses may be suited for autonomous operations as they follow set routes and schedules. However, a research gap exists in whether or not parents would be willing to have their children ride in autonomously operated school buses. The purpose of this study was to examine parents’ willingness to allow their child to ride in an autonomous school bus. Participant gender and nationality were also two independent variables, along with affect measures as a possible mediating variable. The research used a two-study approach. In study one, it was found that participants were less willing to have their child ride in a driverless school bus than a traditional human-operated vehicle. In study two, findings suggest a significant interaction between the type of driver, participant gender, and nationality. In general, American females were less willing than Indian females and overall, Americans were less willing than Indians in the driverless conditions. Affect was found to be a mediating variable, which suggests that emotions were playing a role in the responses of participants. The paper concludes with theoretical contributions, practical applications, and suggestions for future research.

Environmental accounting of eco-innovations through environmental input-output analysis : The case of hydrogen and fuel cells buses

NARCIS (Netherlands)

Cantono, Simona; Heijungs, Reinout; Kleijn, Réne

The introduction of environmentally friendly innovations in both transport and energy sectors are included in the list of priorities of the European Union political agenda. This paper investigates the environmental consequences of the introduction of hydrogen and fuel cells technology in the

Hybrid Turbine Electric Vehicle

Science.gov (United States)

Viterna, Larry A.

1997-01-01

Hybrid electric power trains may revolutionize today's ground passenger vehicles by significantly improving fuel economy and decreasing emissions. The NASA Lewis Research Center is working with industry, universities, and Government to develop and demonstrate a hybrid electric vehicle. Our partners include Bowling Green State University, the Cleveland Regional Transit Authority, Lincoln Electric Motor Division, the State of Ohio's Department of Development, and Teledyne Ryan Aeronautical. The vehicle will be a heavy class urban transit bus offering double the fuel economy of today's buses and emissions that are reduced to 1/10th of the Environmental Protection Agency's standards. At the heart of the vehicle's drive train is a natural-gas-fueled engine. Initially, a small automotive engine will be tested as a baseline. This will be followed by the introduction of an advanced gas turbine developed from an aircraft jet engine. The engine turns a high-speed generator, producing electricity. Power from both the generator and an onboard energy storage system is then provided to a variable-speed electric motor attached to the rear drive axle. An intelligent power-control system determines the most efficient operation of the engine and energy storage system.

75 FR 53521 - Procedures for the Handling of Retaliation Complaints Under the National Transit Systems Security...

Science.gov (United States)

2010-08-31

... discrimination, demotion, discharge, suspension, threats, harassment, reprimand, retaliation, or any other manner... include school buses, charter, or intercity bus transportation or intercity passenger rail transportation... regular and continuous general or special transportation to the public, but does not include school buses...

Phase transition of a cobalt-free perovskite as a high-performance cathode for intermediate-temperature solid oxide fuel cells.

Science.gov (United States)

Jiang, Shanshan; Zhou, Wei; Niu, Yingjie; Zhu, Zhonghua; Shao, Zongping

2012-10-01

It is generally recognized that the phase transition of a perovskite may be detrimental to the connection between cathode and electrolyte. Moreover, certain phase transitions may induce the formation of poor electronic and ionic conducting phase(s), thereby lowering the electrochemical performance of the cathode. Here, we present a study on the phase transition of a cobalt-free perovskite (SrNb(0.1)Fe(0.9)O(3-δ), SNF) and evaluate its effect on the electrochemical performance of the fuel cell. SNF exists as a primitive perovskite structure with space group P4mm (99) at room temperature. As evidenced by in situ high-temperature X-ray diffraction measurements over the temperature range of 600 to 1000 °C, SNF undergoes a transformation to a tetragonal structure with a space group I4/m (87). This phase transition is accompanied by a moderate change in the volume, allowing a good cathode/electrolyte interface on thermal cycling. According to the electrochemical impedance spectroscopy evaluation, the I4/m phase exhibits positive effects on the cathode's performance, showing the highest oxygen reduction reaction activity of cobalt-free cathodes reported so far. This activity improvement is attributed to enhanced oxygen surface processes. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Morphology of single inhalable particle inside public transit biodiesel fueled bus.

Science.gov (United States)

Shandilya, Kaushik K; Kumar, Ashok

2010-01-01

In an urban-transit bus, fueled by biodiesel in Toledo, Ohio, single inhalable particle samples in October 2008 were collected and detected by scanning electron microscopy and energy dispersive X-ray spectrometry (SEM/EDS). Particle size analysis found bimodal distribution at 0.2 and 0.5 microm. The particle morphology was characterized by 14 different shape clusters: square, pentagon, hexagon, heptagon, octagon, nonagon, decagon, agglomerate, sphere, triangle, oblong, strip, line or stick, and unknown, by quantitative order. The square particles were common in the samples. Round and triangle particles are more, and pentagon, hexagon, heptagon, octagon, nonagon, decagon, strip, line or sticks are less. Agglomerate particles were found in abundance. The surface of most particles was coarse with a fractal edge that can provide a suitable chemical reaction bed in the polluted atmospheric environment. The three sorts of surface patterns of squares were smooth, semi-smooth, and coarse. The three sorts of square surface patterns represented the morphological characteristics of single inhalable particles in the air inside the bus in Toledo. The size and shape distribution results were compared to those obtained for a bus using ultra low sulfur diesel.

White paper: Preliminary assessment of LNG vehicle technology, economics, and safety issues (Revision 1). Topical report, April-August 1991

International Nuclear Information System (INIS)

Powars, C.; Lucher, D.; Moyer, C.; Browning, L.

1992-01-01

The objective of the study is to evaluate the potential of LNG as a vehicle fuel, to determine market niches, and to identify needed technology improvements. The white paper is being issued when the work is approximately 30 percent complete to preview the study direction, draw preliminary conclusions, and make initial recommendations. Interim findings relative to LNG vehicle technology, economics, and safety are presented. It is important to decide if heavier hydrocarbons should be allowed in LNG vehicle fuel. Development of suitable refueling couplings and vehicle fuel supply pressure systems are recommended. Initial economics analyses considered transit buses and pickup and delivery trucks fueled via onsite liquefiers and imported LNG. Net user costs were more than (but in some cases close to) those for diesel fuel and gasoline. Lowering the cost of small-scale liquefiers would significantly improve the economics of LNG vehicles. New emissions regulations may introduce considerations beyond simple cost comparisons. LNG vehicle safety and available accident data are reviewed. Consistent codes for LNG vehicles and refueling facilities are needed

Fuel choices for fuel-cell vehicles : well-to-wheel energy and emission impacts

International Nuclear Information System (INIS)

Wang, M.

2002-01-01

Because of their high energy efficiencies and low emissions, fuel-cell vehicles (FCVs) are undergoing extensive research and development. While hydrogen will likely be the ultimate fuel to power fuel-cell vehicles, because of current infrastructure constraints, hydrogen-carrying fuels are being investigated as transitional fuel-cell fuels. A complete well-to-wheels (WTW) evaluation of fuel-cell vehicle energy and emission effects that examines (1) energy feedstock recovery and transportation; (2) fuel production, transportation, and distribution; and (3) vehicle operation must be conducted to assist decision makers in selecting the fuel-cell fuels that achieve the greatest energy and emission benefits. A fuel-cycle model developed at Argonne National Laboratory--called the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model--was used to evaluate well-to-wheels energy and emission impacts of various fuel-cell fuels. The results show that different fuel-cell fuels can have significantly different energy and greenhouse gas emission effects. Therefore, if fuel-cell vehicles are to achieve the envisioned energy and emission reduction benefits, pathways for producing the fuels that power them must be carefully examined.

Numerical modeling of laboratory-scale surface-to-crown fire transition

Science.gov (United States)

Castle, Drew Clayton

Understanding the conditions leading to the transition of fire spread from a surface fuel to an elevated (crown) fuel is critical to effective fire risk assessment and management. Surface fires that successfully transition to crown fires can be very difficult to suppress, potentially leading to damages in the natural and built environments. This is relevant to chaparral shrub lands which are common throughout parts of the Southwest U.S. and represent a significant part of the wildland urban interface. The ability of the Wildland-Urban Interface Fire Dynamic Simulator (WFDS) to model surface-to-crown fire transition was evaluated through comparison to laboratory experiments. The WFDS model is being developed by the U.S. Forest Service (USFS) and the National Institute of Standards and Technology. The experiments were conducted at the USFS Forest Fire Laboratory in Riverside, California. The experiments measured the ignition of chamise (Adenostoma fasciculatum) crown fuel held above a surface fire spreading through excelsior fuel. Cases with different crown fuel bulk densities, crown fuel base heights, and imposed wind speeds were considered. Cold-flow simulations yielded wind speed profiles that closely matched the experimental measurements. Next, fire simulations with only the surface fuel were conducted to verify the rate of spread while factors such as substrate properties were varied. Finally, simulations with both a surface fuel and a crown fuel were completed. Examination of specific surface fire characteristics (rate of spread, flame angle, etc.) and the corresponding experimental surface fire behavior provided a basis for comparison of the factors most responsible for transition from a surface fire to the raised fuel ignition. The rate of spread was determined by tracking the flame in the Smokeview animations using a tool developed for tracking an actual flame in a video. WFDS simulations produced results in both surface fire spread and raised fuel bed

A New Dynamic Model for Nuclear Fuel Cycle System Analysis

International Nuclear Information System (INIS)

Choi, Sungyeol; Ko, Won Il

2014-01-01

The evaluation of mass flow is a complex process where numerous parameters and their complex interaction are involved. Given that many nuclear power countries have light and heavy water reactors and associated fuel cycle technologies, the mass flow analysis has to consider a dynamic transition from the open fuel cycle to other cycles over decades or a century. Although an equilibrium analysis provides insight concerning the end-states of fuel cycle transitions, it cannot answer when we need specific management options, whether the current plan can deliver these options when needed, and how fast the equilibrium can be achieved. As a pilot application, the government brought several experts together to conduct preliminary evaluations for nuclear fuel cycle options in 2010. According to Table 1, they concluded that the closed nuclear fuel cycle has long-term advantages over the open fuel cycle. However, it is still necessary to assess these options in depth and to optimize transition paths of these long-term options with advanced dynamic fuel cycle models. A dynamic simulation model for nuclear fuel cycle systems was developed and its dynamic mass flow analysis capability was validated against the results of existing models. This model can reflects a complex combination of various fuel cycle processes and reactor types, from once-through to multiple recycling, within a single nuclear fuel cycle system. For the open fuel cycle, the results of the developed model are well matched with the results of other models

Fuel cell development for transportation: Catalyst development

Energy Technology Data Exchange (ETDEWEB)

Doddapaneni, N. [Sandia National Lab., Albuquerque, NM (United States)

1996-04-01

Fuel cells are being considered as alternate power sources for transportation and stationary applications. With proton exchange membrane (PEM) fuel cells the fuel crossover to cathodes causes severe thermal management and cell voltage drop due to oxidation of fuel at the platinized cathodes. The main goal of this project was to design, synthesize, and evaluate stable and inexpensive transition metal macrocyclic catalysts for the reduction of oxygen and be electrochemically inert towards anode fuels such as hydrogen and methanol.

Kinematics and thermodynamics of non-stoichiometric oxidation phase transitions in spent fuel

International Nuclear Information System (INIS)

Stout, R.B.; Kansa, E.J.; Wijesinghe, A.M.

1993-01-01

At low temperatures ( 2 lattice to a U 4 O 9 lattice but with an oxygen-to-uranium (O/U) ratio of ∼2.4. Also, the weight gain time response has a plateau as the O/U approaches 2.4. Part of this response results from a geometrical dependency as a U 4 O 9 oxidation front propagates into grain volumes Of UO 2 It may also be indicative of a metastable, non-stoichiometric U 4 O 9 phase whose existence may inhibit the transition kinetics to the next expected phase Of U 3 O 8 . To gain a mechanistic understanding and to plan future oxidation tests, lattice kinematic and thermodynamic models are developed for lattice deformations and energetics of lattice phase changes (UO 2 → U 4 O 9 → U 3 0 7 → U 3 O 8) that include zeroth order influences on oxidation kinetics due to interstitial oxygen atoms and vacancies plus interstitial and substitutional actinides and fission decay products in spent fuel

Hawaiian hydrogen mass transit system

International Nuclear Information System (INIS)

Russell, G.W.; Russell, A.

1990-01-01

This paper proposes a joint effort between the scientific and business communities; to create, make and have hydrogen fuel become the primary fuel of the future. Hawaii has abundant, unharnessed renewable resources yet imports almost all of its fuel. Initiating hydrogen production and industrial application in conjunction with a prototype pilot project such as this mass transit system would not only accomplish the joining of science and business but give an environmentally safe energy alternative to the state and people of Hawaii and hopefully the world

Economic aspects of Dukovany NPP fuel cycle

International Nuclear Information System (INIS)

Vesely, P.; Borovicka, M.

2001-01-01

The paper discusses some aspects of high burnup program implementation at Dukovany NPP and its influence on the fuel cycle costs. Dukovany internal fuel cycle is originally designed as a three years cycle of the Out-In-In fuel reloading patterns. These reloads are not only uneconomical but they additionally increased the radiation load of the reactor pressure vessel due to high neutron leakage typical for Out-In-In loading pattern. To avoid the high neutron leakage from the core a transition to 4-year fuel cycle is started in 1987. The neutron leakage from the core is sequentially decreased by insertion of older fuel assemblies at the core periphery. Other developments in fuel cycle are: 1) increasing of enrichment in control assemblies (3.6% of U-235); 2) improvement in fuel assembly design (reduce the assembly shroud thickness from 2.1 to 1.6 mm); 3) introduction of Zr spacer grid instead of stainless steel; 4) introduction of new type of assembly with profiled enrichment with average value of 3.82%. Due to increased reactivity of the new assemblies the transition to the partial 5-year fuel cycle is required. Typical fuel loading pattern for 3, 3.5, 4 and 5-year cycles are shown in the presented paper. An evaluation of fuel cost is also discussed by using comparative analysis of different fuel cycle options. The analysis shows that introduction of the high burnup program has decrease relative fuel cycle costs

A Comparison of Materials Issues for Cermet and Graphite-Based NTP Fuels

Science.gov (United States)

Stewart, Mark E.; Schnitzler, Bruce G.

2013-01-01

This paper compares material issues for cermet and graphite fuel elements. In particular, two issues in NTP fuel element performance are considered here: ductile to brittle transition in relation to crack propagation, and orificing individual coolant channels in fuel elements. Their relevance to fuel element performance is supported by considering material properties, experimental data, and results from multidisciplinary fluid/thermal/structural simulations. Ductile to brittle transition results in a fuel element region prone to brittle fracture under stress, while outside this region, stresses lead to deformation and resilience under stress. Poor coolant distribution between fuel element channels can increase stresses in certain channels. NERVA fuel element experimental results are consistent with this interpretation. An understanding of these mechanisms will help interpret fuel element testing results.

Fuel assembly spacer

International Nuclear Information System (INIS)

Shirakawa, Ken-etsu.

1988-01-01

Purpose: To reduce the pressure loss of coolants by fuel assembly spacers. Constitution: Spacers for supporting a fuel assembly are attached by means of a plurality of wires to an outer frame. The outer frame is made of shape memory alloy such that the wires are caused to slacken at normal temperature and the slacking of the wires is eliminated in excess of the transition temperature. Since the wires slacken at the normal temperature, fuel rods can be inserted easily. After the insertion of the fuel rods, when the entire portion or the outer frame is heated by water or gas at a predetermined temperature, the outer frame resumes its previously memorized shape to tighten the wires and, accordingly, the fuel rods can be supported firmly. In this way, since the fuel rods are inserted in the slacken state of the wires and, after the assembling, the outer frame resumes its memorized shape, the assembling work can be conducted efficiently. (Kamimura, M.)

Analysis of closed-pool boilup using the TRANSIT-HYDRO code

International Nuclear Information System (INIS)

Graff, D.L.

1983-01-01

The benign termination of the transition phase of a hypothetical LMFBR accident rests on the avoidance of highly energetic recriticalities prior to escape of bottled molten core materials from the active core region. In scenarios where molten fuel is trapped due to axial blockages, the maintenance of subcritical configurations until radial flow paths develop requires stable boil-up of the molten fuel/steel mixture. This paper describes the analysis of an experiment investigating the behavior of closed boiling pools using the two-fluid hydrodynamics module of TRANSIT-HYDRO, a deterministic transition-phase analysis code

Final report : Calgary Transit customer satisfaction survey 2005

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-02-15

This survey was conducted to measure the customer satisfaction of Calgary Transit users and gather information for further service improvements. The survey was conducted by telephone with a total of 500 current customers, and results were compared with previous surveys. The average number of trips per week among regular customers was 7.6, the lowest over the past 6 years. Twenty-six per cent of customers used the service more frequently due to higher gas prices, lack of a vehicle and the higher frequency of services. While most customers used buses, there was an increase in train usage in 2005, which was attributed to an increase in service frequency. Customers typically reported travelling during rush hour periods. Transit customers assigned a global score of 8.2 for service quality satisfaction and loyalty, which was consistent with previous scores. Seventy-two per cent of customers rated service quality as excellent or good. Approximately 1 in 5 customers perceived Calgary Transit to have improved over the previous year. Nearly half of the customers identified themselves as committed users of the service compared to other transportation methods, and most customers stated that having more service during peak hours and in new communities should be priorities. Sixty-four per cent of respondents supported fare increases to fund service additions. It was concluded that there was a significant increase in overall transit use in 2005, which may have been due to its perceived convenience and the influence of economic factors. It was noted that the increase has not affected customers' perceptions of service performance. 8 tabs., 9 figs.

Transportable Emissions Testing Laboratory for Alternative Vehicles Emissions Testing

Energy Technology Data Exchange (ETDEWEB)

Clark, Nigel

2012-01-31

The overall objective of this project was to perform research to quantify and improve the energy efficiency and the exhaust emissions reduction from advanced technology vehicles using clean, renewable and alternative fuels. Advanced vehicle and alternative fuel fleets were to be identified, and selected vehicles characterized for emissions and efficiency. Target vehicles were to include transit buses, school buses, vocational trucks, delivery trucks, and tractor-trailers. Gaseous species measured were to include carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, and particulate matter. An objective was to characterize particulate matter more deeply than by mass. Accurate characterization of efficiency and emissions was to be accomplished using a state-of-the-art portable emissions measurement system and an accompanying chassis dynamometer available at West Virginia University. These two units, combined, are termed the Transportable Laboratory. An objective was to load the vehicles in a real-world fashion, using coast down data to establish rolling resistance and wind drag, and to apply the coast down data to the dynamometer control. Test schedules created from actual vehicle operation were to be employed, and a specific objective of the research was to assess the effect of choosing a test schedule which the subject vehicle either cannot follow or can substantially outperform. In addition the vehicle loading objective was to be met better with an improved flywheel system.

Alcohols/Ethers as Oxygenates in Diesel Fuel: Properties of Blended Fuels and Evaluation of Practiacl Experiences

Energy Technology Data Exchange (ETDEWEB)

Nylund, N.; Aakko, P. [TEC Trans Energy Consulting Ltd (Finland); Niemi, S.; Paanu, T. [Turku Polytechnic (Finland); Berg, R. [Befri Konsult (Sweden)

2005-03-15

is also of importance. So far, no engine manufacturers have indicated they will extend warranty coverage to their equipment when operating with E-diesel. They believe there are simply too many unanswered questions as well as the potential for liability exposure due to the increased flammability range of E-diesel. The reports on field tests with oxygenated diesel fuels are rather scarce, especially reports on recent tests. There are, however, some reports available on engine tests and tests with trucks, buses and even off-road equipment. Most of the available test results identified fuel economy and cost as the only appreciable differences between E-diesel and conventional diesel fuel. Most emissions tests with heavy-duty engines confirm the effect of a substantial reduction in PM when running with E-diesel. The typical range for PM reduction is 20 -- 40 %. Most studies also report reduced NOx emissions. Earlier, there were a lot of activities with E-diesel in Sweden. For the time being, California and Brazil are leading the development of E-diesel.

Alcohols/Ethers as Oxygenates in Diesel Fuel: Properties of Blended Fuels and Evaluation of Practiacl Experiences

Energy Technology Data Exchange (ETDEWEB)

Nylund, N; Aakko, P [TEC Trans Energy Consulting Ltd (Finland); Niemi, S; Paanu, T [Turku Polytechnic (Finland); Berg, R [Befri Konsult (Sweden)

2005-03-15

of importance. So far, no engine manufacturers have indicated they will extend warranty coverage to their equipment when operating with E-diesel. They believe there are simply too many unanswered questions as well as the potential for liability exposure due to the increased flammability range of E-diesel. The reports on field tests with oxygenated diesel fuels are rather scarce, especially reports on recent tests. There are, however, some reports available on engine tests and tests with trucks, buses and even off-road equipment. Most of the available test results identified fuel economy and cost as the only appreciable differences between E-diesel and conventional diesel fuel. Most emissions tests with heavy-duty engines confirm the effect of a substantial reduction in PM when running with E-diesel. The typical range for PM reduction is 20 -- 40 %. Most studies also report reduced NOx emissions. Earlier, there were a lot of activities with E-diesel in Sweden. For the time being, California and Brazil are leading the development of E-diesel.

Ramp-related incidents involving wheeled mobility device users during transit bus boarding/alighting.

Science.gov (United States)

Frost, Karen L; Bertocci, Gina; Smalley, Craig

2015-05-01

To estimate the prevalence of wheeled mobility device (WhMD) ramp-related incidents while boarding/alighting a public transit bus and to determine whether the frequency of incidents is less when the ramp slope meets the proposed Americans with Disabilities Act (ADA) maximum allowable limit of ≤9.5°. Observational study. Community public transportation. WhMD users (N=414) accessing a public transit bus equipped with an instrumented ramp. Not applicable. Prevalence of boarding/alighting incidents involving WhMD users and associated ramp slopes; factors affecting incidents. A total of 4.6% (n=35) of WhMD users experienced an incident while boarding/alighting a transit bus. Significantly more incidents occurred during boarding (6.3%, n=26) than during alighting (2.2%, n=9) (Pboard/alight when the ramp slope exceeded the proposed ADA maximum allowable ramp slope was 5.1 (95% confidence interval, 2.9-9.0; P9.5° and ramps deployed to street level are associated with a higher frequency of incidents and provision of assistance. Transit agencies should increase awareness among bus operators of the effect kneeling and deployment location (street/sidewalk) have on the ramp slope. In addition, ramp components and the built environment may contribute to incidents. When prescribing WhMDs, skills training must include ascending/descending ramps at slopes encountered during boarding/alighting to ensure safe and independent access to public transit buses. Copyright © 2015 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.