WorldWideScience

Sample records for fuel rod surface

  1. Results from studies of surface deposits on the claddings of fuel rods used in RBMK-1000 reactors

    Science.gov (United States)

    Smirnova, I. M.; Markov, D. V.

    2010-07-01

    The results of studies on analyzing the element composition of deposits on the cladding surfaces of fuel rods used in a fuel assembly at the Leningrad nuclear power station are presented. The distribution of elements in deposits over the fuel rod height is analyzed, and the zones of their concentration are revealed. It is shown that deposits of copper penetrating into cracks in the surface layer of zirconium oxide introduce an essential contribution in the development of nodular corrosion of fuel rod claddings.

  2. Heat Transfer Enhancement By Three-Dimensional Surface Roughness Technique In Nuclear Fuel Rod Bundles

    Science.gov (United States)

    Najeeb, Umair

    This thesis experimentally investigates the enhancement of single-phase heat transfer, frictional loss and pressure drop characteristics in a Single Heater Element Loop Tester (SHELT). The heater element simulates a single fuel rod for Pressurized Nuclear reactor. In this experimental investigation, the effect of the outer surface roughness of a simulated nuclear rod bundle was studied. The outer surface of a simulated fuel rod was created with a three-dimensional (Diamond-shaped blocks) surface roughness. The angle of corrugation for each diamond was 45 degrees. The length of each side of a diamond block is 1 mm. The depth of each diamond block was 0.3 mm. The pitch of the pattern was 1.614 mm. The simulated fuel rod had an outside diameter of 9.5 mm and wall thickness of 1.5 mm and was placed in a test-section made of 38.1 mm inner diameter, wall thickness 6.35 mm aluminum pipe. The Simulated fuel rod was made of Nickel 200 and Inconel 625 materials. The fuel rod was connected to 10 KW DC power supply. The Inconel 625 material of the rod with an electrical resistance of 32.3 kO was used to generate heat inside the test-section. The heat energy dissipated from the Inconel tube due to the flow of electrical current flows into the working fluid across the rod at constant heat flux conditions. The DI water was employed as working fluid for this experimental investigation. The temperature and pressure readings for both smooth and rough regions of the fuel rod were recorded and compared later to find enhancement in heat transfer coefficient and increment in the pressure drops. Tests were conducted for Reynold's Numbers ranging from 10e4 to 10e5. Enhancement in heat transfer coefficient at all Re was recorded. The maximum heat transfer co-efficient enhancement recorded was 86% at Re = 4.18e5. It was also observed that the pressure drop and friction factor increased by 14.7% due to the increased surface roughness.

  3. Local Fuel Rod Crud Prediction Tool Applications

    Energy Technology Data Exchange (ETDEWEB)

    Krammen, Michael A.; Karoutas, Zeses E.; Wang, Guoqiang; Young, Michael Y

    2009-06-15

    response to two CILC fuel failures observed in a reactor plant where fuel rod crudding was not initially of concern due to negligible predicted fuel rod steaming on a fuel assembly sub-channel scale. The fuel rod crud observed in the reactor cycle with the fuel rod CILC failures was very localized, but was heaviest on those fuel rods with relatively higher fuel rod duty. These indications led to development of the more locally detailed predictive capability. And, based on the observed behavior, guideline limits have been established by benchmarking the methodology to the fuel rod crud induced fuel failures. The guideline limits are used in designing fuel managements. Application of these tools in subsequent fuel management design for later reactor cycles in both the plant where the CILC fuel failures occurred and in its sister plant with similar operating characteristics have avoided a recurrence of the CILC fuel failure. These tools were also used when a new fuel design with mixing vane grids was introduced in two plants previously fueled with non-mixing vane grids. The predictive tools account for the thermal hydraulic transition core effects. Interestingly, the plant with the generally higher fuel duty, a plant that had experienced Crud Induced Power Shift (CIPS) in earlier cycles, is predicted to easily meet the CIPS and CILC guidelines for the transition and following cycle. While the other plant, which has not experienced CIPS in earlier cycles, is predicted to be operating close to the CILC guideline limits in the transition cycle. The higher duty plant is predicted to have appreciable fuel rod surface area that is steaming over the reactor cycle, while the lower duty plant is predicted to have relatively little fuel rod surface area in steaming. The interpretation is that with a relatively similar crud source in the coolant, a smaller steaming surface area may act as a stronger sink for the available crud, resulting in locally thicker crud. This is a similar

  4. Fabrication of preliminary fuel rods for SFR

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sun Ki; Oh, Seok Jin; Ko, Young Mo; Woo, Youn Myung; Kim, Ki Hwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-05-15

    Metal fuels was selected for fueling many of the first reactors in the US, including the Experimental Breeder Reactor-I (EBR-I) and the Experimental Breeder Reactor-II (EBR-II) in Idaho, the FERMI-I reactor, and the Dounreay Fast Reactor (DFR) in the UK. Metallic U.Pu.Zr alloys were the reference fuel for the US Integral Fast Reactor (IFR) program. Metallic fuel has advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant and inherent passive safety. U-Zr-Pu alloy fuels have been used for SFR (sodium-cooled fast reactor) related to the closed fuel cycle for managing minor actinides and reducing a high radioactivity levels since the 1980s. Fabrication technology of metallic fuel for SFR has been in development in Korea as a national nuclear R and D program since 2007. For the final goal of SFR fuel rod fabrication with good performance, recently, three preliminary fuel rods were fabricated. In this paper, the preliminary fuel rods were fabricated, and then the inspection for QC(quality control) of the fuel rods was performed

  5. Double-clad nuclear fuel safety rod

    Science.gov (United States)

    McCarthy, William H.; Atcheson, Donald B.; Vaidyanathan, Swaminathan

    1984-01-01

    A device for shutting down a nuclear reactor during an undercooling or overpower event, whether or not the reactor's scram system operates properly. This is accomplished by double-clad fuel safety rods positioned at various locations throughout the reactor core, wherein melting of a secondary internal cladding of the rod allows the fuel column therein to shift from the reactor core to place the reactor in a subcritical condition.

  6. International symposium on fuel rod simulators: development and application

    Energy Technology Data Exchange (ETDEWEB)

    McCulloch, R.W. (comp.)

    1981-05-01

    Separate abstracts are included for each of the papers presented concerning fuel rod simulator operation and performance; simulator design and evaluation; clad heated fuel rod simulators and fuel rod simulators for cladding investigations; fuel rod simulator components and inspection; and simulator analytical modeling. Ten papers have previously been input to the Energy Data Base.

  7. Quivers For Special Fuel Rods-Disposal Of Special Fuel Rods In CASTOR V Casks

    Energy Technology Data Exchange (ETDEWEB)

    Bannani, Amin; Cebula, Wojciech; Buchmuller, Olga; Huggenberg, Roland [GNS, Essen (Germany); Helmut Kuhl [WTI, Julich (Germany)

    2015-05-15

    While GNS casks of the CASTOR family are a suitable means to transfer fuel assemblies (FA) from the NPP to an interim dry storage site, Germanys phase-out of nuclear energy has triggered the demand for an additional solution to dispose of special fuel rods (SFR), normally remaining in the fuel pond until the final shutdown of the NPP. SFR are fuel rods that had to be removed from fuel assemblies mainly due to their special condition, e. g. damages in the cladding of the fuel rods which may have occurred during reactor operations. SFR are usually stored in the spent fuel pond after they are removed from the FA. The quiver for special fuel rods features a robust yet simple design, with a high mechanical stability, a reliable leak-tightness and large safety margins for future requirements on safety analysis. The quiver for special fuel rods can be easily adapted to a large variety of different damaged fuel rods and tailored to the specific need of the customer. The quiver for special fuel rods is adaptable e.g. in length and diameter for use in other types of transport and storage casks and is applicable in other countries as well. The overall concept presented here is a first of its kind solution for the disposal of SFRs via Castor V-casks. This provides an important precondition in achieving the status 'free from nuclear fuel' of the shut down German NPPs.

  8. Optimization of fuel rod enrichment distribution for BWR fuel assembly

    Energy Technology Data Exchange (ETDEWEB)

    Hirano, Yasushi; Hida, Kazuki; Sakurada, Koichi; Yamamoto, Munenari [Toshiba Corp., Kawasaki, Kanagawa (Japan). Nuclear Engineering Lab.

    1996-09-01

    A practical method was developed for determining the optimum fuel enrichment distribution within a boiling water reactor fuel assembly. The method deals with two different optimization problems, i.e. the combinatorial optimization problem of grouping fuel rods into a given number of rod groups with the same enrichment, and the problem of determining an optimal enrichment for each fuel rod under the resultant rod-grouping pattern. In solving these problems, the primary goal is to minimize a predefined objective function over a given exposure period. The objective function used here is defined by the linear combination C{sub 1}X + C{sub 2}X{sub G}, where X and X{sub G} stand, respectively, for control variables giving constraint to the local power peaking factor and the gadolinium rod power. C{sub 1} and C{sub 2} are user-definable weighting factors to accommodate design preferences. The algorithm for solving this combinatorial optimization problem starts by finding the optimal enrichment vector without any rod-grouping, and promising candidates of rod-grouping patterns are found by exhaustive enumeration based on the resulting fuel enrichment ordering. This latter problem is solved using the method of approximation programming. A practical application is shown for a contemporary 8 x 8 Pu mixed-oxide fuel assembly with 10 gadolinium-poisoned rods. (author)

  9. Spent nuclear fuel rods encapsulated in copper

    Energy Technology Data Exchange (ETDEWEB)

    Hanes, H.D.

    1984-04-01

    Using hot isostatic pressing, spent nuclear fuel rods and other radioactive wastes can be encapsulated in solid copper. The copper capsule which is formed is free of pores and cracks, and is highly resistant to attack by reducing ground waters. Such capsules should contain radioactive materials safely for hundreds of thousands of years in underground storage.

  10. Metallography and Microanalysis of Qinshan PhaseⅠ NPP Spent Fuel Rods

    Institute of Scientific and Technical Information of China (English)

    QIAN; Jin; BIAN; Wei; GUO; Li-na; GUO; Yi-fan; CHU; Feng-min; LIANG; Zheng-qiang

    2015-01-01

    Qinshan PhaseⅠNPP is a first domestic commercial PWR and its fuel rods and fuel assembly were designed and manufactured by China.In order to assess the irradiation properties of the fuel rods,8spent fuel rods which were drew out from 3fuel assemblies were transferred to CIAE hot cells for post irradiation examination(PIE)in 2014.The cladding material of the fuel

  11. Development of burnup dependent fuel rod model in COBRA-TF

    Science.gov (United States)

    Yilmaz, Mine Ozdemir

    predictions. After confirming that the new fuel thermal conductivity model in CTF worked and provided consistent results with FRAPTRAN predictions for a single fuel rod configuration, the same type of analysis was carried out for a bigger system which is the 4x4 PWR bundle consisting of 15 fuel pins and one control guide tube. Steady- state calculations at Hot Full Power (HFP) conditions for control guide tube out (unrodded) were performed using the 4x4 PWR array with CTF/TORT-TD coupled code system. Fuel centerline, surface and average temperatures predicted by CTF/TORT-TD with and without the new fuel thermal conductivity model were compared against CTF/TORT-TD/FRAPTRAN predictions to demonstrate the improvement in fuel centerline predictions when new model was used. In addition to that constant and CTF dynamic gap conductance model were used with the new thermal conductivity model to show the performance of the CTF dynamic gap conductance model and its impact on fuel centerline and surface temperatures. Finally, a Rod Ejection Accident (REA) scenario using the same 4x4 PWR array was run both at Hot Zero Power (HZP) and Hot Full Power (HFP) condition, starting at a position where half of the control rod is inserted. This scenario was run using CTF/TORT-TD coupled code system with and without the new fuel thermal conductivity model. The purpose of this transient analysis was to show the impact of thermal conductivity degradation (TCD) on feedback effects, specifically Doppler Reactivity Coefficient (DRC) and, eventually, total core reactivity.

  12. Cladding corrosion and hydriding in irradiated defected zircaloy fuel rods (LWBR Development Program)

    Energy Technology Data Exchange (ETDEWEB)

    Clayton, J.C.

    1985-08-01

    Twenty-one LWBR irradiation test rods containing ThO/sub 2/-UO/sub 2/ fuel and Zircaloy cladding with holes or cracks operated successfully. Zircaloy cladding corrosion on the inside and outside diameter surfaces and hydrogen pickup in the cladding were measured. The observed outer surface Zircaloy cladding corrosion oxide thicknesses of the test rods were similar to thicknesses measured for nondefected irradiation test rods. An analysis model, which was developed to calculate outer surface oxide thickness of non-defected rods, gave results which were in reasonable agreement with the outer surface oxide thicknesses of defected rods. When the analysis procedure was modified to account for additional corrosion proportional to fission rate and to time, the calculated values agreed well with measured inner oxide corrosion film values. Hydrogen pickup in the defected rods was not directly proportional to local corrosion oxide weight gain as was the case for non-defected rods. 16 refs., 6 figs., 8 tabs.

  13. Electric Fuel Rod Simulator Fabrication at ORNL

    Science.gov (United States)

    Ott, Larry J.; McCulloch, Reg

    2004-02-01

    Commercial vendors could not supply the high-quality, highly instrumented electric fuel rod simulators (FRS) required for large thermal-hydraulic safety-oriented experiments at the Oak Ridge National Laboratory (ORNL) in the 1970s and early 1980s. Staff at ORNL designed, developed, and manufactured the simulators utilized in these safety experiments. Important FRS design requirements include (1) materials of construction, (2) test power requirements and availability, (3) experimental test objectives, (4) supporting thermal analyses, and (5) extensive quality control throughout all phases of FRS fabrication. This paper will present an overview of these requirements (design, analytics, and quality control) as practiced at ORNL to produce a durable high-quality FRS.

  14. Dependence of control rod worth on fuel burnup

    Energy Technology Data Exchange (ETDEWEB)

    Savva, P., E-mail: savvapan@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PoB 60228, 15310 Aghia Paraskevi (Greece); Varvayanni, M., E-mail: melina@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PoB 60228, 15310 Aghia Paraskevi (Greece); Catsaros, N., E-mail: nicos@ipta.demokritos.g [NCSR ' DEMOKRITOS' , PoB 60228, 15310 Aghia Paraskevi (Greece)

    2011-02-15

    Research highlights: Diffusion and MC calculations for rod worth dependence on burnup and Xe in reactors. One-step rod withdrawal/insertion are used for rod worth estimation. The study showed that when Xe is present the rods worth is significantly reduced. Rod worth variation with burnup depends on rod position in core. Rod worth obtained with MC code is higher than that obtained from deterministic. - Abstract: One important parameter in the design and the analysis of a nuclear reactor core is the reactivity worth of the control rods, i.e. their efficiency to absorb excess reactivity. The control rod worth is affected by parameters such as the fuel burnup in the rod vicinity, the Xe concentration in the core, the operational time of the rod and its position in the core. In the present work, two different computational approaches, a deterministic and a stochastic one, were used for the determination of the rods worth dependence on the fuel burnup level and the Xe concentration level in a conceptual, symmetric reactor core, based on the MTR fuel assemblies used in the Greek Research Reactor (GRR-1). For the deterministic approach the neutronics code system composed by the SCALE modules NITAWL and XSDRN and the diffusion code CITATION was used, while for the stochastic one the Monte Carlo code TRIPOLI was applied. The study showed that when Xe is present in the core, the rods worth is significantly reduced, while the rod worth variation with increasing burnup depends on the rods position in the core grid. The rod worth obtained with the use of the Monte Carlo code is higher than the one obtained from the deterministic code.

  15. Axial gas flow in irradiated PWR fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Dagbjartsson, S.J.; Murdock, B.A.; Owen, D.E.; MacDonald, P.E.

    1977-09-01

    Transient and steady state axial gas flow experiments were performed on six irradiated, commercial pressurized water reactor fuel rods at ambient temperature and 533 K. Laminar flow equations, as used in the FRAP-T2 and SSYST fuel behavior codes, were used with the gas flow results to calculate effective fuel rod radial gaps. The results of these analyses were compared with measured gap sizes obtained from metallographic examination of one fuel rod. Using measured gap sizes as input, the SSYST code was used to calculate pressure drops and mass fluxes and the results were compared with the experimental gas flow data.

  16. Optimization of fuel rod enrichment distribution to minimize rod power peaking throughout life within BWR fuel assembly

    Energy Technology Data Exchange (ETDEWEB)

    Hirano, Yasushi; Hida, Kazuki; Sakurada, Koichi; Yamamoto, Munenari [Toshiba Corp., Kawasaki, Kanagawa (Japan). Nuclear Engineering Lab.

    1997-01-01

    A practical method was developed for determining the optimum fuel enrichment distribution within a boiling water reactor fuel assembly. The method deals with two different optimization problems, i.e. a combinatorial optimization problem grouping fuel rods into a given number of rod groups with the same enrichment, and a problem determining an optimal enrichment for each fuel rod under the resultant rod-grouping pattern. In solving these problems, the primary goal is to minimize a predefined objective function over a given exposure period. The objective function used here is defined by a linear combination: C{sub 1}X+C{sub 2}X{sub G}, where X and X{sub G} stand for a control variable to give the constraint respectively for a local power peaking factor and a gadolinium rod power, and C{sub 1} and C{sub 2} are user-definable weighting factor to accommodate the design preference. The algorithm of solving the combinatorial optimization problem starts with finding the optimal enrichment vector without any rod-grouping, and promising candidates of rod-grouping patterns are found by exhaustive enumeration based on the resulting fuel enrichment ordering, and then the latter problem is solved by using the method of approximation programming. The practical application of the present method is shown for a contemporary 8x8 Pu mixed-oxide fuel assembly with 10 gadolinium-poisoned rods. (author)

  17. Treatment of defective fuel rods for interim storage

    Energy Technology Data Exchange (ETDEWEB)

    Muenchow, K.; Hummel, W. [AREVA NP GmbH, Erlangen (Germany)

    2013-07-01

    In this paper we look exclusively at the treatment of defective fuel rods for long-term dry interim storage at the nuclear power plant, in order to avoid off-site transports. AREVA has developed a technique that allows verifiably adequate drying of the defective fuel rods and reconstructs the barrier for retaining radioactive materials. This is done by individually encapsulating the defective fuel rods and achieving gas-tightness by seal welding. This guarantees the retention of radioactive materials during the storage period of at least 40 years in a transport and storage flask in an interim storage facility at site. (orig.)

  18. Gamma-ray spectroscopy on irradiated fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Terremoto, Luis Antonio Albiac [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Engenharia Nuclear], e-mail: laaterre@ipen.br

    2009-07-01

    The recording of gamma-ray spectra along an irradiated fuel rod allows the fission products to be qualitatively and quantitatively examined. Among all nondestructive examinations performed on irradiated fuel rods by gamma-ray spectroscopy, the most comprehensive one is the average burnup measurement, which is quantitative. Moreover, burnup measurements by means of gamma-ray spectroscopy are less time-consuming and waste-generating than burnup measurements by radiochemical, destructive methods. This work presents the theoretical foundations and experimental techniques necessary to measure, using nondestructive gamma-ray spectroscopy, the average burnup of irradiated fuel rods in a laboratory equipped with hot cells. (author)

  19. Internal hydriding in irradiated defected Zircaloy fuel rods: A review (LWBR Development Program)

    Energy Technology Data Exchange (ETDEWEB)

    Clayton, J C

    1987-10-01

    Although not a problem in recent commercial power reactors, including the Shippingport Light Water Breeder Reactor, internal hydriding of Zircaloy cladding was a persistent cause of gross cladding failures during the 1960s. It occurred in the fuel rods of water-cooled nuclear power reactors that had a small cladding defect. This report summarizes the experimental findings, causes, mechanisms, and methods of minimizing internal hydriding in defected Zircaloy-clad fuel rods. Irradiation test data on the different types of defected fuel rods, intentionally fabricated defected and in-pile operationally defected rods, are compared. Significant factors affecting internal hydriding in defected Zircaloy-clad fuel rods (defect hole size, internal and external sources of hydrogen, Zircaloy cladding surface properties, nickel alloy contamination of Zircaloy, the effect of heat flux and fluence) are discussed. Pertinent in-pile and out-of-pile test results from Bettis and other laboratories are used as a data base in constructing a qualitative model which explains hydrogen generation and distribution in Zircaloy cladding of defected water-cooled reactor fuel rods. Techniques for minimizing internal hydride failures in Zircaloy-clad fuel rods are evaluated.

  20. Fuel rod behavior under normal operating conditions in Super Fast Reactor with high power density

    Energy Technology Data Exchange (ETDEWEB)

    Ju, Haitao, E-mail: haitaoju@gmail.com [Science and Technology on Reactor System Design Technology Laboratory, Chengdu, Sichuan 610041 (China); Ishiwatari, Yuki [Department of Nuclear Engineering and Management, The University of Tokyo, Hongo, Bunkyo, Tokyo 113-8656 (Japan); Oka, Yoshiaki [Joint Department of Nuclear Energy, Waseda University, Totsukamachi, Shinjuku, Tokyo 169-8050 (Japan)

    2015-08-15

    Highlights: • The improved core of Super Fast Reactor with high power density is analyzed. • We analyzed four types of the limiting fuel rods. • The influence of Pu enrichment and compressive stress to yield strength ratio are analyzed. • The improved fuel rod design of the new core is suggested. - Abstract: A Super Fast Reactor is a pressure-vessel type, fast spectrum SuperCritical Water Reactor (SCWR) which is presently researched in a Japanese project. A preliminary core has an average power density of 158.8 W/cc. However one of the most important advantages of the Super Fast Reactor is the higher power density compared to the thermal spectrum SCWR, which reduces the capital cost. After the sensitivity analyses on the fuel rod configurations, the fuel assembly configurations and the core configurations, an improved core with an average power density of 294.8 W/cc is designed by 3-D neutronic/thermal-hydraulic coupled calculations. In order to ensure the fuel rod integrity of new core design with high power density, the fuel rod behaviors under normal operating condition are analyzed using fuel performance code FEMAXI-6. The power histories of each fuel rod are taken from the neutronics calculation results in the core design. The cladding surface temperature histories are generated from the thermal-hydraulic calculation results in the core design. Four types of the limiting fuel rods, individually with the Maximum Cladding Surface Temperature (MCST), Maximum Power Peak (MPP), Maximum Discharge Burnup (MDB) and Different Coolant Flow Pattern (DCFP), are chosen to cover all the fuel rods in the core. The available design range of the fuel rod design parameters, such as initial gas plenum pressure, gas plenum position, gas plenum length, grain size and gap size, are found out in order to satisfy the following design criteria: (1) Maximum fuel centerline temperature should be less than 1900 °C. (2) Maximum cladding stress in circumferential direction should

  1. Double-clad nuclear-fuel safety rod

    Science.gov (United States)

    McCarthy, W.H.; Atcheson, D.B.

    1981-12-30

    A device for shutting down a nuclear reactor during an undercooling or overpower event, whether or not the reactor's scram system operates properly. This is accomplished by double-clad fuel safety rods positioned at various locations throughout the reactor core, wherein melting of a secondary internal cladding of the rod allows the fuel column therein to shift from the reactor core to place the reactor in a subcritical condition.

  2. Vernotte-Cattaneo approximation for heat conduction in fuel rod

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa P, G.; Espinosa M, E. G. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Area de Ingenieria en Recursos Energeticos, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (Mexico)], e-mail: gepe@xanum.uam.mx

    2009-10-15

    In this paper we explore the applicability of a fuel rod mathematical model based on the Vernotte-Cattaneo transient heat conduction as constitutive law (Non-Fourier approach) for light water reactors transient analysis. In the classical theory of diffusion, the Fourier law of heat conduction is used to describe the relation between the heat conduction is used to describe the relation between the heat flux vector and the temperature gradient assuming that the heat propagation speeds are infinite. The motivation for this research was to eliminate the paradox of an infinite. The motivation for this research was to eliminate the paradox of an infinite thermal wave speed. The time-dependent heat sources were considered in the fuel rod heat transfer model. The close of the main steam isolated valves transient in a boiling water reactor was analyzed for different relaxation times. The results show that for long-times the heat fluxes on the clad surface under Vernotte-Cattaneo approach can be important, while for short-times and from the engineering point of view the changes are very small. (Author)

  3. Nuclear Fuel Test Rod Fabrication for Data Acquisition Test

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Chang-Young; Hong, Jin-Tae; Kim, Ka-Hye; Huh, Sung-Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    A nuclear fuel test rod must be fabricated with precise welding and assembly technologies, and confirmed for their soundness. Recently, we have developed various kinds of processing systems such as an orbital TIG welding system, a fiber laser welding system, an automated drilling system and a helium leak analyzer, which are able to fabricate the nuclear fuel test rods and rigs, and keep inspection systems to confirm the soundness of the nuclear fuel test rods and rids. The orbital TIG welding system can be used with two kinds of welding methods. One can perform the round welding for end-caps of a nuclear fuel test rod by an orbital head mounted in a low-pressure chamber. The other can do spot welding for a pin-hole of a nuclear fuel test rod in a high-pressure chamber to fill up helium gas of high pressure. The fiber laser welding system can weld cylindrical and 3 axis samples such as parts of a nuclear fuel test rod and instrumentation sensors which is moved by an index chuck and a 3 axis (X, Y, Z) servo stage controlled by the CNC program. To measure the real-time temperature change at the center of the nuclear fuel during the irradiation test, a thermocouple should be instrumented at that position. Therefore, a hole needs to be made at the center of fuel pellet to instrument the thermocouple. An automated drilling system can drill a fine hole into a fuel pellet without changing tools or breaking the work-piece. The helium leak analyzer (ASM-380 model of DEIXEN Co.) can check the leak of the nuclear fuel test rod filled with helium gas. This paper describes not only the assembly and fabrication methods used by the process systems, but also the results of the data acquisition test for the nuclear fuel test rod. A nuclear fuel test rod for the data acquisition test was fabricated using the welding and assembling echnologies acquired from previous tests.

  4. Experimental Study on Surrogate Nuclear Fuel Rods under Reversed Cyclic Bending

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hong [ORNL; Wang, Jy-An John [ORNL

    2017-01-01

    The mechanical behavior of spent nuclear fuel (SNF) rods under reversed cyclic bending or bending fatigue must be understood to evaluate their vibration integrity in a transportation environment. This is especially important for high-burnup fuels (>45 GWd/MTU), which have the potential for increased structural damage. It has been demonstrated that the bending fatigue of SNF rods can be effectively studied using surrogate rods. In this investigation, surrogate rods made of stainless steel (SS) 304 cladding and aluminum oxide pellets were tested under load or moment control at a variety of amplitude levels at 5 Hz using the Cyclic Integrated Reversible-Bending Fatigue Tester developed at Oak Ridge National Laboratory. The behavior of the rods was further characterized using flexural rigidity and hysteresis data, and fractography was performed on the failed rods. The proposed surrogate rods captured many of the characteristics of deformation and failure mode observed in SNF, including the linear-to-nonlinear deformation transition and large residual curvature in static tests, PPI and PCMI failure mechanisms, and large variation in the initial structural condition. Rod degradation was measured and characterized by measuring the flexural rigidity; the degradation of the rigidity depended on both the moment amplitude applied and the initial structural condition of the rods. It was also shown that a cracking initiation site can be located on the internal surface or the external surface of cladding. Finally, fatigue damage to the bending rods can be described in terms of flexural rigidity, and the fatigue life of rods can be predicted once damage model parameters are properly evaluated. The developed experimental approach, test protocol, and analysis method can be used to study the vibration integrity of SNF rods in the future.

  5. High burnup effects in WWER fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Smirnov, V.; Smirnov, A. [RRC Research Institute of Atomic Reactors, Dimitrovqrad (Russian Federation)

    1996-03-01

    Since 1987 at the Research Institute of Atomic Reactors, the examinations of the WWER spent fuel assemblies has been carried out. These investigations are aimed to gain information on WWER spent fuel conditions in order to validate the fuel assemblies use during the 3 and 4 year fuel cycle in the WWER-440 and WWER-1000 units. At present time, the aim is to reach an average fuel burnup of 55 MWd/kgU. According to this aim, a new investigation program on the WWER spent fuel elements is started. The main objectives of this program are to study the high burnup effects and their influence on the WWER fuel properties. This paper presented the main statistical values of the WWER-440 and WWER-1000 reactors` fuel assemblies and their fragment parameters. Average burnup of fuel in the investigated fuel assemblies was in the range of 13 to 49.7 MWd/kgU. In this case, the numer of fuel cycles was from 1 to 4 during operation of the fuel assemblies.

  6. Stress Analysis of Single Spacer Grid Support considering Fuel Rod

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Y. G.; Jung, D. H.; Kim, J. H. [Chungnam National University, Daejeon (Korea, Republic of); Park, J. K.; Jeon, K. L. [Korea Nuclear Fuel, Daejeon (Korea, Republic of)

    2010-10-15

    Pressurized water reactor (PWR) nuclear fuel assembly is mainly composed of a top-end piece, a bottom-end piece, lots of fuel rods, and several spacer grids. Among them, the main function of spacer grid is protecting fuel rods from Fluid Induced Vibration (FIV). The cross section of spacer grid assembled by laser welding in upper and lower point. When the fuel rod inserted in spacer gird, spring and dimple and around of welded area got a stresses. The main hypothesis of this analysis is the boundary area of HAZ and base metal can get a lot of damage than other area by FIV. So, design factors of spacer grid mainly considered to preventing the fatigue failure in HAZ and spring and dimple of spacer grid. From previous researching, the environment in reactor verified. Pressure and temperature of light water observed 15MPa and 320 .deg. C, and vibration of the fuel rod observed within 0 {approx} 50Hz. In this study, mechanical properties of zirconium alloy that extracted from the test and the spacer grid model which used in the PWR were applied in stress analyzing. General-purpose finite element analysis program was used ANSYS Workbench 12.0.1 version. 3-D CAD program CATIA was used to create spacer grid model

  7. CFD analysis of rewetting vertical nuclear fuel rod by dispersed fluid jet impingement

    Directory of Open Access Journals (Sweden)

    Ajoy Debbarma

    2016-09-01

    Full Text Available Numerical analysis of cooling assessment in hot vertical fuel rod is carryout using ANSYS 14.0 – CFX Solver. Rewetting is the process of re-establishment of coolants with hot surfaces. Numerical validation exercise carried out with number of turbulence and shear stress turbulence model fairly predict the experimental data and used for further investigation. In the present paper, dispersed fluid is simulating with CFX solver to investigate the flow boiling process in emergency cooling of vertical fuel rod. When coolants come in contact on the hot surface this may not initiated the wetting patch. However, this paper introduces the unique jet impingement direction to remove the heat from the hot surface. In this report, the rewetting temperature and wetting delay also described during in progress of wetting front movement in hot vertical rod.

  8. Process development and fabrication for sphere-pac fuel rods. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Welty, R.K.; Campbell, M.H.

    1981-06-01

    Uranium fuel rods containing sphere-pac fuel have been fabricated for in-reactor tests and demonstrations. A process for the development, qualification, and fabrication of acceptable sphere-pac fuel rods is described. Special equipment to control fuel contamination with moisture or air and the equipment layout needed for rod fabrication is described and tests for assuring the uniformity of the fuel column are discussed. Fuel retainers required for sphere-pac fuel column stability and instrumentation to measure fuel column smear density are described. Results of sphere-pac fuel rod fabrication campaigns are reviewed and recommended improvements for high throughput production are noted.

  9. Estimation and control in HTGR fuel rod fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Downing, D J; Bailey, M J

    1980-01-01

    A control algorithm has been derived for a HTGR Fuel Rod Fabrication Process utilizing the method of Box and Jenkins. The estimator is a Kalman filter and is compared with a Least Square estimator and a standard control chart. The effects of system delays are presented.

  10. Experimental fuel rod stored energy determination. STEED I project

    Energy Technology Data Exchange (ETDEWEB)

    Engman, U.; Malen, K. [Studsvik Nuclear AB, Nykoeping (Sweden)

    1999-06-01

    The objective of the STEED I (STored Energy/Enthalpy Determination) project was to evaluate an experimental method for producing accurate and reliable data concerning the stored energy in fuel rods during operation. The STEED data should provide useful information for LOCA evaluation, fuel design and thermo-mechanical modelling. Stored energy refers to the amount of heat, which at a certain time is stored within the fuel. Physical properties of the fuel that affect the quantity of stored energy are radial power profile, burnup, fuel geometry, fuel density and thermal conductivity and heat capacity of the fuel pellet, and the gas gap conductance. The quantity of stored energy is conveniently studied under transient conditions when all, or part of the stored heat is released. This work describes determination of the stored energy by evaluating scram tests. The R2 test reactor is well suited for this type of experiments, where the thermal response of different types of fuel rods can be evaluated and compared. Scrams have been performed with the intent to evaluate the fuel rod stored energy before the scram. Methods have been developed for evaluation of the stored energy from the scram response It was found that the time dependence for a large part of the heat release from the rod could be described by a single time constant. Evaluations of the time constant have been made from the data in different ways. The stored energy has been evaluated integrating the exponential decay. The integral of the exponential decay is the initial power multiplied by the time constant. This means that differences in the stored energy due to, for instance, rod properties or rod power dependence are best studied using the same time constant. The scram response was modelled with the TOODEE2 transient code. The calculations gave a time constant of about 4 s and very little power dependence. The experimental result is a time constant around 4 s. The small differences in the measurement results

  11. Raman Spectroscopy Analysis of Oxide Film on Spent Fuel Rod Cladding from Qinshan PhaseⅠNPP

    Institute of Scientific and Technical Information of China (English)

    WANG; Hua-cai; TANG; Qi; FU; Cheng; LIANG; Zheng-qiang

    2015-01-01

    The outside surface of cladding is one of the important factors limiting the service life of the fuel rods.Studying the structure of oxide film under reactor operating conditions has great significance in study of the cause of different appearances of cladding,establishing the relationship between oxide film thickness and oxide structure

  12. Test requirement for PIE of HANARO irradiated fuel rod

    Energy Technology Data Exchange (ETDEWEB)

    Lim, I. C.; Cho, Y. G

    2000-06-01

    Since the first criticality of HANARO reached in Feb. of 1995, the rod type U{sub 3}Si-A1 fuel imported from AECL has been used. From the under-water fuel inspection which has been conducted since 1997, a ballooning-rupture type abnormality was observed in several fuel rods. In order to find the root cause of this abnormality and to find the resolution, the post irradiation examination(PIE) was proposed as the best way. In this document, the information from the under-water inspection as well as the PIE requirements are described. Based on the information in this document, a detail test plan will be developed by the project team who shall conduct the PIE.

  13. Strategy for Fuel Rod Receipt, Characterization, Sample Allocation for the Demonstration Sister Rods

    Energy Technology Data Exchange (ETDEWEB)

    Marschman, Steven C. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Warmann, Stephan A. [Portage, Inc., Idaho Falls, ID (United States); Rusch, Chris [NAC International, Inc., Norcross, GA (United States)

    2014-03-01

    , inert gas backfilling, and transfer to an Independent Spent Fuel Storage Installation (ISFSI) for multi-year storage. To document the initial condition of the used fuel prior to emplacement in a storage system, “sister ” fuel rods will be harvested and sent to a national laboratory for characterization and archival purposes. This report supports the demonstration by describing how sister rods will be shipped and received at a national laboratory, and recommending basic nondestructive and destructive analyses to assure the fuel rods are adequately characterized for UFDC work. For this report, a hub-and-spoke model is proposed, with one location serving as the hub for fuel rod receipt and characterization. In this model, fuel and/or clad would be sent to other locations when capabilities at the hub were inadequate or nonexistent. This model has been proposed to reduce DOE-NE’s obligation for waste cleanup and decontamination of equipment.

  14. Large-eddy simulation, fuel rod vibration and grid-to-rod fretting in pressurized water reactors

    Science.gov (United States)

    Christon, Mark A.; Lu, Roger; Bakosi, Jozsef; Nadiga, Balasubramanya T.; Karoutas, Zeses; Berndt, Markus

    2016-10-01

    Grid-to-rod fretting (GTRF) in pressurized water reactors is a flow-induced vibration phenomenon that results in wear and fretting of the cladding material on fuel rods. GTRF is responsible for over 70% of the fuel failures in pressurized water reactors in the United States. Predicting the GTRF wear and concomitant interval between failures is important because of the large costs associated with reactor shutdown and replacement of fuel rod assemblies. The GTRF-induced wear process involves turbulent flow, mechanical vibration, tribology, and time-varying irradiated material properties in complex fuel assembly geometries. This paper presents a new approach for predicting GTRF induced fuel rod wear that uses high-resolution implicit large-eddy simulation to drive nonlinear transient dynamics computations. The GTRF fluid-structure problem is separated into the simulation of the turbulent flow field in the complex-geometry fuel-rod bundles using implicit large-eddy simulation, the calculation of statistics of the resulting fluctuating structural forces, and the nonlinear transient dynamics analysis of the fuel rod. Ultimately, the methods developed here, can be used, in conjunction with operational management, to improve reactor core designs in which fuel rod failures are minimized or potentially eliminated. Robustness of the behavior of both the structural forces computed from the turbulent flow simulations and the results from the transient dynamics analyses highlight the progress made towards achieving a predictive simulation capability for the GTRF problem.

  15. Investigation of Backscatter X-ray imaging techniques for Uranium Dioxide Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, Timothy D [Rensselaer Polytechnic Institute (RPI); Hollenbach, Daniel F [ORNL; Shedlock, Daniel [Nucsafe, Inc.

    2011-01-01

    Radiography by Selective Detection (RSD), was investigated for its ability to determine the presence and types of defects in a UO{sub 2} fuel rod surrounded by zirconium cladding. Images created using a Monte Carlo model compared favorably with actual X-ray backscatter images from mock fuel rods. A fuel rod was modeled as a rectangular parallelepiped with zirconium cladding, and pencil beam X-ray sources of 160 kVp (79 keV avg) and 480 kVp (218 keV avg) were generated using the Monte Carlo N-Particle Transport Code to attempt to image void and palladium (Pd) defects in the interior and on the surface of the fuel pellet. It was found that the 160 kVp spectrum was unable to detect the presence of interior defects, whereas the 480 kVp spectrum detected them with both the standard and the RSD backscatter methods, though the RSD method was very inefficient. It was also found that both energy spectra were able to detect void and Pd defects on the surface using both imaging methods. Additionally, two mock fuel rods were imaged using a backscatter X-ray imaging system, one consisting of hafnium pellets in a Zircaloy-4 cladding and the other consisting of steel pellets in a Zircalloy-4 cladding which was then encased in a steel cladding (a double encapsulation configuration employed in irradiation and experiments). It was found that the system was capable of detecting individual HfO{sub 2} pellets in a Zircaloy-4 cladding and may be capable of detecting individual steel pellets in the double-encapsulated sample. It is expected that the system would also be capable of detecting individual UO{sub 2} pellets in a Zircaloy-4 cladding, though no UO{sub 2} fuel rod was available for imaging.

  16. CALCULATION OF STRESS AND DEFORMATION IN FUEL ROD CLADDING DURING PELLET-CLADDING INTERACTION

    Directory of Open Access Journals (Sweden)

    Dávid Halabuk

    2015-12-01

    Full Text Available The elementary parts of every fuel assembly, and thus of the reactor core, are fuel rods. The main function of cladding is hermetic separation of nuclear fuel from coolant. The fuel rod works in very specific and difficult conditions, so there are high requirements on its reliability and safety. During irradiation of fuel rods, a state may occur when fuel pellet and cladding interact. This state is followed by changes of stress and deformations in the fuel cladding. The article is focused on stress and deformation analysis of fuel cladding, where two fuels are compared: a fresh one and a spent one, which is in contact with cladding. The calculations are done for 4 different shapes of fuel pellets. It is possible to evaluate which shape of fuel pellet is the most appropriate in consideration of stress and deformation forming in fuel cladding, axial dilatation of fuel, and radial temperature distribution in the fuel rod, based on the obtained results.

  17. Vibration mechanism of fuel rod in axial flow

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Heung Seok; Yoon, Kyung Ho; Kim, Hyung Kyu; Song, Kee Nam

    1998-08-01

    This is a review on the previous researches for the vibration of fuel rod induced by axial flow. The analysis methods are classified into three categories accordingly as the researchers postulate the vibration to be self-excited, forced and parametric; the self-excited mechanism by Burgreen and Quinn, the forced one by Reavis, Gorman, kanazawa, and S. Chen, and the parametric one by Y. Chen. Quinn supposed that the centrifugal force by flow exaggerated the natural bow in the cylinder, and the flexural force by it diminished the bow by turns; this interactive motion leaded cylinder to vibration. The supporters to the forced mechanism considered the forces arising from pressure perturbation within the boundary layers as vibrating sources. Y. Chen insisted that the cylinder could only be excited to vibration in resonance by the small oscillation of mean flow velocity. The previous studies were based on the simple boundary conditions such as hinged-hinged or fixed-fixed single span. Therefore, for the moreaccurate prediction of the fuel rod vibration in reactor, the further studies need to reflect the actual boundary conditions of the fuel rod like axial force and continuous supports by grids. (author). 25 refs.

  18. Three dimensional considerations in thermal-hydraulics of helical cruciform fuel rods for LWR power uprates

    Energy Technology Data Exchange (ETDEWEB)

    Shirvan, Koroush, E-mail: kshirvan@mit.edu; Kazimi, Mujid S.

    2014-04-01

    Highlights: • We benchmarked the 4 × 4 helical cruciform fuel (HCF) bundle pressure drop experimental data with CFD. • We also benchmarked the 4 × 4 HCF mixing experimental data with CFD. • We derived new friction factors for PWR and BWR designs at PWR and BWR operating conditions from CFD. • We showed the importance of modeling the 3D conduction in HCF in steady state and transient conditions. - Abstract: In order to increase the power density of current and new light water reactor designs, the helical cruciform fuel (HCF) rods have been proposed. The HCF rod is equivalent to a thin cylindrical rod, with 4 fuel containing vanes, wrapped around it. The HCF rods increase the surface area to volume ratio of the fuel and enhance the inter-subchannel mixing due to their helical shape. The rods do not need supporting grids, as they are packed to periodically contact their neighbors along the flow direction, enabling a higher power density in the core. The HCF rods were reported to have the potential to uprate existing PWRs by 45% and BWRs by 20%. In order to quantify the mixing behavior of the HCF rods based on their twist pitch, experiments were previously performed at atmospheric pressures with single phase water in a 4 by 4 HCF and cylindrical rod bundles. In this paper, the experimental results on pressure drop and mixing are benchmarked with computational fluid dynamic (CFD) using steady state the Reynolds average Navier–Stokes (RANS) turbulence model. The sensitivity of the CFD approach to computational domain, mesh size, mesh shape and RANS turbulence models are examined against the experimental conditions. Due to the refined radial velocity profile from the HCF rods twist, the turbulence models showed little sensitivity to the domain. Based on the CFD simulations, the total pressure drops under the PWR and BWR conditions are expected to be about 10% higher than the values previously reported solely from an empirical correlation based on the

  19. Investigation of Minimum Film boiling Phenomena on Fuel Rods Under Blowdown Cooling Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Stephen M. Bajorek; Michael Gawron; Timothy Etzel; Lucas Peterson

    2003-06-30

    Blowdon cooling heat transfer is an important process that occurs early in a hypothetical large break loss-of-coolant accident (LOCA) in a pressurized water reactor. During blowdown, the flow through the hot assembly is a post-critical heat flux dispersed droplet flow. The heat transfer mechanisms that occur in blowdown cooling are complex and depend on droplet and heated surface interaction. In a safety analysis, it is of considerable importance to determine the thermal-hydraulic conditions leading to the minimum film boiling temperature, Tmin. A flow boiling rig for measurement of blowdown cooling heat transfer and quench phenomena on a nuclear fuel rod simulator was designed and constructed for operation at up to 12.4 MPa. The test section consisted of a concentric annulus, with a 9.5 mm OD nuclear fuel rod simulator at the center. The rod was contained within a 0.85 mm thick, 19 mm OD 316 stainless steel tube, forming the flow channel. Two types of rods were tested; one type was sheathed with Inconel 600 while the other was clad with Zircaloy-2. Water was injected into the test section at the top of the heated length through an injection header. This header was an annular sign that fit around the fuel rod simulator and within the stainless steel tube. Small spacers aligned the injection header and prevented contract with either the heater rod or the tube. A series of small diameter holes at the bottom of the header caused the formation of droplets that became entrained with the steam flow. The test section design was such that quench would take place on the rod, and not along the channel outer annulus.

  20. Models for fuel rod behaviour at high burnup

    Energy Technology Data Exchange (ETDEWEB)

    Jernkvist, Lars O.; Massih, Ali R. [Quantum Technologies AB, Uppsala Science Park, Uppsala (Sweden)

    2004-12-01

    This report deals with release of fission product gases and irradiation-induced restructuring in uranium dioxide nuclear fuel. Waterside corrosion of zirconium alloy clad tubes to light water reactor fuel rods is also discussed. Computational models, suitable for implementation in the FRAPCON-3.2 computer code, are proposed for these potentially life-limiting phenomena. Hence, an integrated model for the calculation or thermal fission gas release by intragranular diffusion, gas trapping in grain boundaries, irradiation-induced re-solution, grain boundary saturation, and grain boundary sweeping in UO{sub 2} fuel, under time varying temperature loads, is formulated. After a brief review of the status of thermal fission gas release modelling, we delineate the governing equations for the aforementioned processes. Grain growth kinetic modelling is briefly reviewed and pertinent data on grain growth of high burnup fuel obtained during power ramps in the Third Risoe Fission Gas Release Project are evaluated. Sample computations are performed, which clearly show the connection between fission gas release and gram growth as a function of time at different isotherms. Models are also proposed for the restructuring of uranium dioxide fuel at high burnup, the so-called rim formation, and its effect on fuel porosity build-up, fuel thermal conductivity and fission gas release. These models are assessed by use of recent experimental data from the High Burnup Rim Project, as well as from post irradiation examinations of high-burnup fuel, irradiated in power reactors. Moreover, models for clad oxide growth and hydrogen pickup in PWRs, applicable to Zircaloy-4, ZIRLO or M5 cladding, are formulated, based on recent in-reactor corrosion data for high-burnup fuel rods. Our evaluation of these data indicates that the oxidation rate of ZIRLO-type materials is about 20% lower than for standard Zircaloy-4 cladding under typical PWR conditions. Likewise, the oxidation rate of M5 seems to be

  1. Characterization of control rod worths and fuel rod power peaking factors in the university of Utah TRIGA Mark I reactor

    OpenAIRE

    Alroumi Fawaz; Kim Donghoon; Schow Ryan; Jevremovic Tatjana

    2016-01-01

    Control rod reactivity (worths) for the three control rods and fuel rod power peaking factors in the University of Utah research reactor (100 kW TRIGA Mark I) are characterized using the AGENT code system and the results described in this paper. These values are compared to the MCNP6 and existing experimental measurements. In addition, the eigenvalue, neutron spatial flux distributions and reaction rates are analyzed and discussed. The AGENT code system is ...

  2. Multidimensional simulations of hydrides during fuel rod lifecycle

    Science.gov (United States)

    Stafford, D. S.

    2015-11-01

    In light water reactor fuel rods, waterside corrosion of zirconium-alloy cladding introduces hydrogen into the cladding, where it is slightly soluble. When the solubility limit is reached, the hydrogen precipitates into crystals of zirconium hydride which decrease the ductility of the cladding and may lead to cladding failure during dry storage or transportation events. The distribution of the hydride phase and the orientation of the crystals depend on the history of the spatial temperature and stress profiles in the cladding. In this work, we have expanded the existing hydride modeling capability in the BISON fuel performance code with the goal of predicting both global and local effects on the radial, azimuthal and axial distribution of the hydride phase. We compare results from 1D simulations to published experimental data. We demonstrate the new capability by simulating in 2D a fuel rod throughout a lifecycle that includes irradiation, short-term storage in the spent fuel pool, drying, and interim storage in a dry cask. Using the 2D simulations, we present qualitative predictions of the effects of the inter-pellet gap and the drying conditions on the growth of a hydride rim.

  3. Irradiation testing of internally pressurized and/or graphite coated Zircaloy-4 clad fuel rods in the NRX Reactor (AWBA Development Program). [LWBR

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, R.C.; Sherman, J.

    1978-11-01

    Irradiation tests on 0.612 inch O.D. by 117-inch long Zircaloy-4 clad fuel rods were performed to assess the effects on fuel rod performance of (1) internal helium pre-pressurization to 500 psi as fabricated, (2) the presence of a graphite barrier coating on the inside cladding surface, and (3) combined pre-pressurization and graphite coating. Periodic dimensional examinations were performed on the test rods, and the results were compared with data obtained from two previously irradiated test rods--both unpressurized and uncoated and one intentionally defected. These comparisons indicate that both pre-pressurization and graphite coating can substantially improve fuel element performance capability.

  4. FDD-1 System On-line Monitoring Fuel Rod Failure of Nuclear Power Plant

    Institute of Scientific and Technical Information of China (English)

    CHENPeng; ZHANGYing-chao; JISong-tao; GAOYong-guang; YINZhen-guo; HANChuan-bin

    2003-01-01

    The FDD-1 system developed by CIAE for on-line monitoring fuel rod failure of nuclear power plant consists of γ-ray detector, γ-ray spectrum analyzer, computer, and an analysis code for evaluating the status of fuel rod failure. It would be determined that the fuel rod failure occurs when a large amount of γ activity increases in the primary system measured by γ-ray detector near the CVCS.

  5. Non-destructive Testing Dummy Nuclear Fuel Rods by Neutron Radiography

    Institute of Scientific and Technical Information of China (English)

    WEI; Guo-hai; HAN; Song-bai; HE; Lin-feng; WANG; Yu; WANG; Hong-li; LIU; Yun-tao; CHEN; Dong-feng

    2013-01-01

    As a unique non-destructive testing technique,neutron radiography can be used to measure nuclear fuel rods with radioactivity.The images of the dummy nuclear fuel rods were obtained at the CARR.Through imaging analysis methods,the structure defections,the hydrogen accumulation in the cladding and the 235U enrichment of the pellet were studied and analyzed.Experiences for non-destructive testing real PWR nuclear fuel rods by NR

  6. The results of postirradiation examinations of VVER-1000 and VVER-440 fuel rods

    Science.gov (United States)

    Dubrovin, K. P.; Ivanov, E. G.; Strijov, P. N.; Yakovlev, V. V.

    1991-02-01

    The paper presents the results of postirradiation examination of the fuel rods having different fuel-cladding gaps, pellet densities, pellet inner diameters and so on. The fuel rods were irradiated in the material science reactor (MR) of the Kurchatov Institute of Atomic Energy and at 4 unit of the Novo-Voronezh nuclear powerplant. Some data on fission gas release and rod geometry and compared with computer code predictions.

  7. Development of Tools for Treating an Irradiated Fuel Rod Assembly in the Pool of HANARO

    Energy Technology Data Exchange (ETDEWEB)

    Hong, J. T.; Ahn, S. H.; Kim, K. H.; Joung, C. Y. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-07-01

    To inspect a fuel rod during irradiation testing at the test loop of a research reactor, the test rig should be disassembled from the IPS (In-pile test section), and the targeted fuel rod assembly should be disassembled from the test rig and encapsulated in a cask to deliver the assembly to the hot cell. In addition, the fuel rod assembly under inspection in the hot cell should be delivered to the reactor pool and reassembled into the test rig to resume the irradiation test. Because the irradiated fuel rod is highly radioactive, all of the assembly and disassembly operations should be carried out in the reactor pool. Therefore, special tools need to be developed to treat the test rig in the pool of a research reactor. In this study, a new mechanically detachable fuel rod assembly has been developed for intermediate inspection during irradiation test at HANARO. A fuel rod assembly can be divided into two parts, such as an instrumented fuel rod assembly and a non-instrumented fuel rod assembly. In particular, an instrumented fuel rod assembly is assembled at the lower part of the test rig, and a non-instrumented fuel rod assembly is assembled at the bottom of the instrumented fuel rod assembly. The non-instrumented fuel rod assembly is locked in the test rig during irradiation test, and is easily disassembled from the instrumented fuel rod assembly by pushing the anchor button and twisting the non-instrumented fuel rod assembly. In addition, because a test rig is 5.4 meters long and the disassembling operation should be carried out at 6 meters deep in the pool of HANARO, tools to help disassemble and assemble the non-instrumented fuel rod assembly have also been developed. All components were designed to operate mechanically and are made of stainless steel and Al 6061 to minimize the effects from the radioactivity. The performance of the developed fuel rod assembly and tools have been verified through an out pile test.

  8. Mathematical modelling of friction-vibration interactions of nuclear fuel rods

    Directory of Open Access Journals (Sweden)

    Zeman V.

    2016-06-01

    Full Text Available Nuclear fuel rods (FRs are transverselly linked to each other by three spacer grid cells at several vertical levels inside a fuel assembly (FA. Vibration of FA components, caused by the motion of FA support plates in the reactor core, generates variable contact forces between FRs and spacer grid cells. Friction effects in contact surfaces have an influence on the expected lifetime period of nuclear FA in terms of FR cladding fretting wear. This paper introduces an original approach to mathematical modelling and simulation analysis of FR nonlinear vibrations and fretting wear taking into consideration friction forces at all levels of spacer grids.

  9. Sturdy on Orbital TIG Welding Properties for Nuclear Fuel Test Rod

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Changyoung; Hong, Jintae; Kim, Kahye; Huh, Sungho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    We developed a precision TIG welding system that is able to weld the seam between end-caps and a fuel cladding tube for the nuclear fuel test rod and rig. This system can be mainly classified into an orbital TIG welder (AMI, M-207A) and a pressure chamber. The orbital TIG welder can be independently used, and it consists of a power supply unit, a microprocessor, water cooling unit, a gas supply unit and an orbital weld head. In this welder, the power supply unit mainly supplies GTAW power for a welding specimen and controls an arc starting of high frequency, supping of purge gas, arc rotation through the orbital TIG welding head, and automatic timing functions. In addition, the pressure chamber is used to make the welded surface of the cladding specimen clean with the inert gas filled inside the chamber. To precisely weld the cladding tube, a welding process needs to establish a schedule program for an orbital TIG welding. Therefore, the weld tests were performed on a cladding tube and dummy rods under various conditions. This paper describes not only test results on parameters of the purge gas flow rates and the chamber gas pressures for the orbital TIG welding, but also test results on the program establishment of an orbital TIG welding system to weld the fuel test rods. Various welding tests were performed to develop the orbital TIG welding techniques for the nuclear fuel test rod. The width of HAZ of a cladding specimen welded with the identical power during an orbital TIG welding cycle was continuously increased from a welded start-point to a weld end-point because of heat accumulation. The welding effect of the PGFR and CGP shows a relatively large difference for FSS and LSS. Each hole on the cladding specimens was formed in the 1bar CGP with the 20L/min PGFR but not made in the case of the PGFR of 10L/min in the CGP of 2bar. The optimum schedule program of the orbital TIG welding system to weld the nuclear fuel test rod was established through the program

  10. Preliminary Study on Method of Quantitative Measurement of Nuclear Fuel Rod by Neutron CT at CARR

    Institute of Scientific and Technical Information of China (English)

    WEI; Guo-hai; HAN; Song-bai; WANG; Hong-li; HE; Lin-feng; WANG; Yu; WU; Mei-mei; LIU; Yun-tao; CHEN; Dong-feng

    2015-01-01

    Neutron CT technique was applied to the quantitative measurement of the key parameters of nuclear fuel rods at China Advanced Research Reactor(CARR).The sample of dummy nuclear fuel rod was rotated in 180°range,and 900neutron projections were obtained.The 3-D neutron

  11. Testing of LWR fuel rods to support criticality safety analysis of transport accident conditions

    Energy Technology Data Exchange (ETDEWEB)

    Purcell, P.C. [BNFL International Transport, Spent Fuel Services (United Kingdom); Dallongeville, M. [COGEMA Logistics (AREVA Group) (France)

    2004-07-01

    For the transport of low enriched materials, criticality safety may be demonstrated by applying pessimistic modelling assumptions that bound any realistic case. Where Light Water Reactor (LWR) fuel is being transported, enrichment levels are usually too high to permit this approach and more realistic data is needed. This requires a method by which the response of LWR fuel under impact accident conditions can be approximated or bounded. In 2000, BNFL and COGEMA LOGISTICS jointly commenced the Fuel Integrity Project (FIP) whose objective was to develop such methods. COGEMA LOGISTICS were well advanced with a method for determining the impact response of unirradiated fuel, but required further test data before acceptance by the Transport Regulators. The joint project team extensively discussed the required inputs to the FIP, from which it was agreed that BNFL would organise new tests on both unirradiated and irradiated fuel samples and COGEMA LOGISTICS would take major responsibility for evaluating the test results. Tests on unirradiated fuel rod samples involved both dynamic and quasi-static loading on fuel samples. PWR fuel rods loaded with uranium pellets were dropped vertically from 9m onto a rigid target and this was repeated on BWR fuel rods, similar tests on empty fuel rods were also conducted. Quasi-static tests were conducted on 530 mm long PWR and BWR fuel specimens under axial loading. Tests on irradiated fuel samples were conducted on high burn-up fuel rods of both PWR and BWR types. These were believed original to the FIP project and involved applying bending loads to simply supported pressurised rod specimens. In one test the fuel rod was heated to nearly 500oC during loading, all specimens were subject to axial impact before testing. Considerable experience of fuel rod testing and new data was gained from this test programme.

  12. Band Width of Acoustic Resonance Frequency Relatively Natural Frequency of Fuel Rod Vibration

    Energy Technology Data Exchange (ETDEWEB)

    Proskuryakov, Konstantin Nicolaevich; Moukhine, V.S.; Novikov, K.S.; Galivets, E.Yu. [MPEI - TU, 14, Krasnokazarmennaya str., Moscow, 111250 (Russian Federation)

    2009-06-15

    In flow induced vibrations the fluid flow is the energy source that causes vibration. Acoustic resonance in piping may lead to severe problems due to over-stressing of components or significant losses of efficiency. Steady oscillatory flow in NPP primary loop can be induced by the pulsating flow introduced by reactor circulating pump or may be set up by self-excitation. Dynamic forces generated by the turbulent flow of coolant in reactor cores cause fuel rods (FR) and fuel assembly (FA) to vibrate. Flow-induced FR and FA vibrations can generally be broken into three groups: large amplitude 'resonance type' vibrations, which can cause immediate rod failure or severe damage to the rod and its support structure, middle amplitude 'within bandwidth of resonance frequency type' vibrations responsible for more gradual wear and fatigue at the contact surface between the fuel cladding and rod support and small amplitude vibrations, 'out of bandwidth of resonance frequency type' responsible for permissible wear and fatigue at the contact surface between the fuel cladding and rod support. Ultimately, these vibration types can result in a cladding breach, and therefore must be accounted for in the thermal hydraulic design of FR and FA and reactor internals. In paper the technique of definition of quality factor (Q) of acoustic contour of the coolant is presented. The value of Q defines a range of frequencies of acoustic fluctuations of the coolant within which the resonance of oscillations of the structure and the coolant is realized. Method of evaluation of so called band width (BW) of acoustic resonance frequency is worked out and presented in the paper. BW characterises the range of the frequency of coolant pressure oscillations within which the frequency of coolant pressure oscillations matches the fuel assembly's natural frequency of vibration (its resonance frequency). Paper show the way of detuning acoustic resonance from natural

  13. A methodology for the evaluation of fuel rod failures under transportation accidents

    Energy Technology Data Exchange (ETDEWEB)

    Rashid, J.Y.R.; Machiels, A.J. [ANATECH, San Diego, CA (United States)]|[EPRI, Palo Alto (United States)

    2004-07-01

    Recent studies on long-term behavior of high-burnup spent fuel have shown that under normal conditions of stor-age, challenges to cladding integrity from various postulated damage mechanisms, such as delayed hydride crack-ing, stress-corrosion cracking and long-term creep, would not lead to any significant safety concerns during dry storage, and regulatory rules have subsequently been established to ensure that a compatible level of safety is maintained. However, similar safety assurances for spent fuel transportation have not yet been developed, and further studies are currently being conducted to evaluate the conditions under which transportation-related safety issues can be resolved. One of the issues presently under evaluation is the ability and the extent of the fuel as-semblies to maintain non-reconfigured geometry during transportation accidents. This evaluation may determine whether, or not, the shielding, confinement, and criticality safety evaluations can be performed assuming initial fuel assembly geometries. The degree to which spent fuel re-configuration could occur during a transportation accident would depend to a large degree on the number of fuel rod failures and the type and geometry of the failure modes. Such information can only be developed analytically, as there is no direct experimental data that can provide guidance on the level of damage that can be expected. To this end, the paper focuses on the development of a modeling and analysis methodology that deals with this general problem on a generic basis. First consideration is given to defining acci-dent loading that is equivalent to the bounding, although analytically intractable, hypothetical transportation acci-dent of a 9-meter drop onto essentially unyielding surface, which is effectively a condition for impact-limiters de-sign. Second, an analytically robust material constitutive model, an essential element in a successful structural analysis, is required. A material behavior model

  14. Studies of the UO 2-zircaloy chemical interaction and fuel rod relocation modes in a severe fuel damage accident

    Science.gov (United States)

    Shiozawa, S.; Ichikawa, M.; Fujishiro, T.

    1988-06-01

    Experiments have been conducted in the Nuclear Safety Research Reactor (NSRR) at JAERI since 1975 in order to study fuel rod failure behavior under reactivity-initiated accident conditions. Recently the experiments have been focussed on fuel behavior under simulated severe fuel damage (SFD) accident conditions. UO 2-Zircaloy reaction kinetics during very rapid transients at elevated temperatures was studied from a metallurgical point of view. Equilibrium was found to be established even in very rapid transients. The reaction rate equations developed in isothermal studies can be applied to interpret the experimental results. A fuel rod relocation criterion in connection with peak temperatures, environment conditions and initial fuel rod conditions was developed. According to the test results, fuel rod melt down due to liquefaction seems unlikely below the melting temperature of β-Zircaloy.

  15. CFD Validation Benchmark Dataset for Natural Convection in Nuclear Fuel Rod Bundles

    Science.gov (United States)

    Smith, Barton; Jones, Kyle

    2016-11-01

    The present study provide CFD validation benchmark data for coupled fluid flow/convection heat transfer on the exterior of heated rods arranged in a 2 × 2 array. The rod model incorporates grids with swirling veins to resemble a nuclear fuel bundle. The four heated aluminum rods are suspended in an open-circuit wind tunnel. Boundary conditions (BCs) are measured and uncertainties calculated to provide all quantities necessary to successfully conduct a CFD validation exercise. System response quantities (SRQs) are measured for comparing the simulation output to the experiment. Stereoscopic Particle Image Velocimetry (SPIV) is used to non-intrusively measure 3-component velocity fields. A through-plane measurement is used for the inflow while laser sheet planes aligned with the flow direction at several downstream locations are used for system response quantities. Two constant heat flux rod surface conditions are presented (400 W/m2 and 700 W/m2) achieving a peak Rayleigh number of 1010 . Uncertainty for all measured variables is reported. The boundary conditions, system response, and all material properties are now available online for download. The U.S. Department of Energy Nuclear Engineering University Program provided the funding for these experiments under Grant 00128493.

  16. Design and analysis of 19 pin annular fuel rod cluster for pressure tube type boiling water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Deokule, A.P., E-mail: abhijit.deokule1986@gmail.com [Homi Bhabha National Institute, Trombay 400 085, Mumbai (India); Vishnoi, A.K.; Dasgupta, A.; Umasankari, K.; Chandraker, D.K.; Vijayan, P.K. [Bhabha Atomic Research Centre, Trombay 400 085, Mumbai (India)

    2014-09-15

    Highlights: • Development of 19 pin annular fuel rod cluster. • Reactor physics study of designed annular fuel rod cluster. • Thermal hydraulic study of annular fuel rod cluster. - Abstract: An assessment of 33 pin annular fuel rod cluster has been carried out previously for possible use in a pressure tube type boiling water reactor. Despite the benefits such as negative coolant void reactivity and larger heat transfer area, the 33 pin annular fuel rod cluster is having lower discharge burn up as compared to solid fuel rod cluster when all other parameters are kept the same. The power rating of this design cannot be increased beyond 20% of the corresponding solid fuel rod cluster. The limitation on the power is not due to physics parameters rather it comes from the thermal hydraulics side. In order to increase power rating of the annular fuel cluster, keeping same pressure tube diameter, the pin diameter was increased, achieving larger inside flow area. However, this reduces the number of annular fuel rods. In spite of this, the power of the annular fuel cluster can be increased by 30% compared to the solid fuel rod cluster. This makes the nineteen pin annular fuel rod cluster a suitable option to extract more power without any major changes in the existing design of the fuel. In the present study reactor physics and thermal hydraulic analysis carried out with different annular fuel rod cluster geometry is reported in detail.

  17. A High Fidelity Multiphysics Framework for Modeling CRUD Deposition on PWR Fuel Rods

    Science.gov (United States)

    Walter, Daniel John

    Corrosion products on the fuel cladding surfaces within pressurized water reactor fuel assemblies have had a significant impact on reactor operation. These types of deposits are referred to as CRUD and can lead to power shifts, as a consequence of the accumulation of solid boron phases on the fuel rod surfaces. Corrosion deposits can also lead to fuel failure resulting from localized corrosion, where the increased thermal resistance of the deposit leads to higher cladding temperatures. The prediction of these occurrences requires a comprehensive model of local thermal hydraulic and chemical processes occurring in close proximity to the cladding surface, as well as their driving factors. Such factors include the rod power distribution, coolant corrosion product concentration, as well as the feedbacks between heat transfer, fluid dynamics, chemistry, and neutronics. To correctly capture the coupled physics and corresponding feedbacks, a high fidelity framework is developed that predicts three-dimensional CRUD deposition on a rod-by-rod basis. Multiphysics boundary conditions resulting from the coupling of heat transfer, fluid dynamics, coolant chemistry, CRUD deposition, neutron transport, and nuclide transmutation inform the CRUD deposition solver. Through systematic parametric sensitivity studies of the CRUD property inputs, coupled boundary conditions, and multiphysics feedback mechanisms, the most important variables of multiphysics CRUD modeling are identified. Moreover, the modeling framework is challenged with a blind comparison of plant data to predictions by a simulation of a sub-assembly within the Seabrook nuclear plant that experienced CRUD induced fuel failures. The physics within the computational framework are loosely coupled via an operator-splitting technique. A control theory approach is adopted to determine the temporal discretization at which to execute a data transfer from one physics to another. The coupled stepsize selection is viewed as a

  18. Effects of fuel relocation on reflood in a partially-blocked rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Byoung Jae [School of Mechanical Engineering, Chungnam National University, 99 Daehak-ro, Yuseong-gu, Daejeon 34134 (Korea, Republic of); Kim, Jongrok; Kim, Kihwan; Bae, Sung Won [Thermal-Hydraulic Safety Research Division, Korea Atomic Energy Research Division, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of); Moon, Sang-Ki, E-mail: skmoon@kaeri.re.kr [Thermal-Hydraulic Safety Research Division, Korea Atomic Energy Research Division, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of)

    2017-02-15

    Ballooning of the fuel rods has been an important issue, since it can influence the coolability of the rod bundle in a large-break loss-of-coolant accident (LBLOCA). Numerous past studies have investigated the effect of blockage geometry on the heat transfer in a partially blocked rod bundle. However, they did not consider the occurrence of fuel relocation and the corresponding effect on two-phase heat transfer. Some fragmented fuel particles located above the ballooned region may drop into the enlarged volume of the balloon. Accordingly, the fuel relocation brings in a local power increase in the ballooned region. The present study’s objective is to investigate the effect of the fuel relocation on the reflood under a LBLOCA condition. Toward this end, experiments were performed in a 5 × 5 partially-blocked rod bundle. Two power profiles were tested: one is a typical cosine shape and the other is the modified shape considering the effect of the fuel relocation. For a typical power shape, the peak temperature in the ballooned rods was lower than that in the intact rods. On the other hand, for the modified power shape, the peak temperature in the ballooned rods was higher than that in the intact rods. Numerical simulations were also performed using the MARS code. The tendencies of the peak clad temperatures were well predicted.

  19. Assessment of precision gamma scanning for inspecting LWR fuel rods. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, J.R.; Barnes, B.K.; Barnes, M.L.; Hamlin, D.K.; Medina-Ortega, E.G.

    1981-07-01

    Reconstruction of the radial two-dimensional distributions of fission products using projections obtained by nondestructive gamma scanning was evaluated. The filtered backprojection algorithm provided the best reconstruction for simulated gamma-ray sources, as well as for actual irradiated fuel material. Both a low-burnup (11.5 GWd/tU) light-water reactor fuel rod and a high-burnup (179.1 GWd/tU) fast breeder reactor fuel rod were examined using this technique.

  20. Uncertainty analysis of spent nuclear fuel isotopics and rod internal pressure

    Science.gov (United States)

    Bratton, Ryan N.

    The bias and uncertainty in fuel isotopic calculations for a well-defined radio- chemical assay benchmark are investigated with Sampler, the new sampling-based uncertainty quantification tool in the SCALE code system. Isotopic predictions are compared to measurements of fuel rod MKP109 of assembly D047 from the Calvert Cliffs Unit 1 core at three axial locations, representing a range of discharged fuel burnups. A methodology is developed which quantifies the significance of input parameter uncertainties and modeling decisions on isotopic prediction by compar- ing to isotopic measurement uncertainties. The SCALE Sampler model of the D047 assembly incorporates input parameter uncertainties for key input data such as multigroup cross sections, decay constants, fission product yields, the cladding thickness, and the power history for fuel rod MKP109. The effects of each set of input parameter uncertainty on the uncertainty of isotopic predictions have been quantified. In this work, isotopic prediction biases are identified and an investiga- tion into their sources is proposed; namely, biases have been identified for certain plutonium, europium, and gadolinium isotopes for all three axial locations. More- over, isotopic prediction uncertainty resulting from only nuclear data is found to be greatest for Eu-154, Gd-154, and Gd-160. The discharge rod internal pressure (RIP) and cladding hoop stress (CHS) distributions are quantified for Watts Bar Nuclear Unit 1 (WBN1) fuel rods by modeling core cycle design data, operation data (including modeling significant trips and downpowers), and as-built fuel enrichments and densities of each fuel rod in FRAPCON-3.5. A methodology is developed which tracks inter-cycle as- sembly movements and assembly batch fabrication information to build individual FRAPCON inputs for each considered WBN1 fuel rod. An alternate model for the amount of helium released from zirconium diboride (ZrB2) integral fuel burn- able absorber (IFBA) layers is

  1. Development of nuclear fuel rod inspection technique using ultrasonic resonance phenomenon

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Myung Sun; Lee, Jong Po; Ju, Young Sang [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-11-01

    Acoustic resonance scattering from a nuclear fuel rod in water is analyzed. A new model for the background which is attributed to the interference of reflected wave and diffracted wave is found and here named {sup t}he inherent background{sup .} The resonance spectrum of a fuel rod is obtained by subtracting the inherent background from the scattered pressure. And also analyzed are the effect of material damping of cladding tube and pellet on the resonance spectrum of a fuel rod. The propagation characteristics of circumferential waves which cause the resonances of cladding tube is produced and the appropriate resonance modes for the application to the inspection of assembled fuel rods are selected. The resonance modes are experimentally measured for pre- and post-irradiated fuel rods and the validation of the fuel rod inspection using ultrasonic resonance phenomenon is examined. And thin ultrasonic sensors accessible into the narrow interval (about 2-3mm) between assembled fuel rods are designed and manufactured. 14 refs. (Author).

  2. Final Report: Contractor Readiness Assessment (CRA) for TREAT Fuel Movement and Control Rod Drives Isolation

    Energy Technology Data Exchange (ETDEWEB)

    Rowsell, David Leon [Idaho National Laboratory (INL), Idaho Falls, ID (United States)

    2015-06-01

    This report documents the Contractor Readiness Assessment (CRA) for TREAT Fuel Movement and Control Rod Drives Isolation. The review followed the approved Plan of Action (POA) and Implementation Plan (IP) using the identified core requirements. The activity was limited scope focusing on the control rod drives functional isolation and fuel element movement. The purpose of this review is to ensure the facility's readiness to move fuel elements thus supporting inspection and functionally isolate the control rod drives to maintain the required shutdown margin.

  3. Development of Welding and Instrumentation Technology for Nuclear Fuel Test Rod

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Chang Young; Ahn, Sung Ho; Heo, Sung Ho; Hong, Jin Tae; Kim, Ka Hye [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    It is necessary to develop various types of welding, instrumentation and helium gas filling techniques that can conduct TIG spot welding exactly at a pin-hole of the end-cap on the nuclear fuel rod to fill up helium gas. The welding process is one of the most important among the instrumentation processes of the nuclear fuel test rod. To manufacture the nuclear fuel test rod, a precision welding system needs to be fabricated to develop various welding technologies of the fuel test rod jointing the various sensors and end-caps on a fuel cladding tube, which is charged with fuel pellets and component parts. We therefore designed and fabricated an orbital TIG welding system and a laser welding system. This paper describes not only some experiment results from weld tests for the parts of a nuclear fuel test rod, but also the contents for the instrumentation process of the dummy fuel test rod installed with the C-type T. C. A dummy nuclear fuel test rod was successfully fabricated with the welding and instrumentation technologies acquired with various tests. In the test results, the round welding has shown a good weldability at both the orbital TIG welding system and the fiber laser welding system. The spot welding to fill up helium gas has shown a good welding performance at a welding current of 30A, welding time of 0.4 sec and gap of 1 mm in a helium gas atmosphere. The soundness of the nuclear fuel test rod sealed by a mechanical sealing method was confirmed by helium leak tests and microstructural analyses.

  4. Computer simulation of the behaviour and performance of a CANDU fuel rod

    Energy Technology Data Exchange (ETDEWEB)

    Marino, A.C. [Comison Nacional de Energia Atomica (Argentina)

    1997-07-01

    At the Argentine Atomic Energy Commission (Comision Nacional de Energia Atomica, CNEA) the BACO code (for 'BArra COmbustible', fuel rod) was developed. It allows the simulation of the thermo-mechanical performance of a cylindrical fuel rod in a Pressurized Heavy Water Reactor (PHWR). The standard present version of the code (2.30), is a powerful tool for a relatively easy and complete evaluation of fuel behaviour predictions. Input parameters and, therefore, output ones may include statistical dispersion. As a demonstration of BACO capabilities we include a review of CANDU fuel applications, and the calculation and a parametric analysis of a characteristic CANDU fuel. (author)

  5. Characterization of control rod worths and fuel rod power peaking factors in the university of Utah TRIGA Mark I reactor

    Directory of Open Access Journals (Sweden)

    Alroumi Fawaz

    2016-01-01

    Full Text Available Control rod reactivity (worths for the three control rods and fuel rod power peaking factors in the University of Utah research reactor (100 kW TRIGA Mark I are characterized using the AGENT code system and the results described in this paper. These values are compared to the MCNP6 and existing experimental measurements. In addition, the eigenvalue, neutron spatial flux distributions and reaction rates are analyzed and discussed. The AGENT code system is widely benchmarked for various reactor types and complexities in their geometric arrangements of the assemblies and reactor core material distributions. Thus, it is used as a base methodology to evaluate neutronics variables of the research reactor at the University of Utah. With its much shorter computation time than MCNP6, AGENT provides agreement with the MCNP6 within a 0.5 % difference for the eigenvalue and a maximum difference of 10% in the power peaking factor values. Differential and integral control rod worths obtained by AGENT show well agreement with MCNP6 and the theoretical model. However, regulating the control rod worth is somewhat overestimated by both MCNP6 and AGENT models when compared to the experimental/theoretical values. In comparison to MCNP6, the total control rod worths and shutdown margin obtained with AGENT show better agreement to the experimental values.

  6. Literature search on Light Water Reactor (LWR) fuel and absorber rod fabrication, 1960--1976

    Energy Technology Data Exchange (ETDEWEB)

    Sample, C R [comp.

    1977-02-01

    A literature search was conducted to provide information supporting the design of a conceptual Light Water Reactor (LWR) Fuel Fabrication plant. Emphasis was placed on fuel processing and pin bundle fabrication, effects of fuel impurities and microstructure on performance and densification, quality assurance, absorber and poison rod fabrication, and fuel pin welding. All data have been taken from publicly available documents, journals, and books. This work was sponsored by the Finishing Processes-Mixed Oxide (MOX) Fuel Fabrication Studies program at HEDL.

  7. Development of nuclear fuel rod inspection technique using ultrasonic resonance phenomenon

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Myoung Seon; Joo, Young Sang; Jung, Hyun Kyu; Cheong, Yong Moo

    1997-02-01

    The scattering of plane acoustic waves normally incident on a multilayered cylindrical shell has been formulated using the global matrix approach. And a simple way to formulate the non-resonant background component in the field scattered by an empty elastic shell has been found. This is to replace the surface admittance for the shell with the zero-frequency limit of the surface admittance for the analogous fluid shell (i.e., the shear wave speed in the elastic shell is set to zero). It has been shown that the background thus obtained is exact and applicable to shells of arbitrary thickness and material makeup, and over all frequencies and mode numbers. This way has been also applied to obtain the expressions of the backgrounds for multilayered shells. The resonant ultrasound spectroscopy system has been constructed to measure the resonance spectrum of a single fuel rod. The leak-defective fuel rod detection system of a laboratory scale has been also constructed. Particularly, all techniques and processes necessary for manufacturing the ultrasonic probe of thin (1.2 mm) strip type have been developed. (author). 38 refs., 34 figs.

  8. Determination of Experimental Fuel Rod Parameters using 3D Modelling of PCMI with MPS Defect

    Energy Technology Data Exchange (ETDEWEB)

    Casagranda, Albert [Idaho National Laboratory; Spencer, Benjamin Whiting [Idaho National Laboratory; Pastore, Giovanni [Idaho National Laboratory; Novascone, Stephen Rhead [Idaho National Laboratory; Hales, Jason Dean [Idaho National Laboratory; Williamson, Richard L [Idaho National Laboratory; Martineau, Richard Charles [Idaho National Laboratory

    2016-05-01

    An in-reactor experiment is being designed in order to validate the pellet-cladding mechanical interaction (PCMI) behavior of the BISON fuel performance code. The experimental parameters for the test rod being placed in the Halden Research Reactor are being determined using BISON simulations. The 3D model includes a missing pellet surface (MPS) defect to generate large local cladding deformations, which should be measureable after typical burnup times. The BISON fuel performance code is being developed at Idaho National Laboratory (INL) and is built on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. BISON supports both 2D and 3D finite elements and solves the fully coupled equations for solid mechanics, heat conduction and species diffusion. A number of fuel performance effects are included using models for swelling, densification, creep, relocation and fission gas production & release. In addition, the mechanical and thermal contact between the fuel and cladding is explicitly modelled using a master-slave based contact algorithm. In order to accurately predict PCMI effects, the BISON code includes the relevant physics involved and provides a scalable and robust solution procedure. The depth of the proposed MPS defect is being varied in the BISON model to establish an optimum value for the experiment. The experiment will be interrupted approximately every 6 months to measure cladding radial deformation and provide data to validate BISON. The complete rodlet (~20 discrete pellets) is being simulated using a 180° half symmetry 3D model with MPS defects at two axial locations. In addition, annular pellets will be used at the top and bottom of the pellet stack to allow thermocouples within the rod to measure the fuel centerline temperature. Simulation results will be presented to illustrate the expected PCMI behavior and support the chosen experimental design parameters.

  9. Analysis of Experimental Fuel Rod Parameters using 3D Modelling of PCMI with MPS Defect

    Energy Technology Data Exchange (ETDEWEB)

    Casagranda, Albert [Idaho National Laboratory; Spencer, Benjamin Whiting [Idaho National Laboratory; Pastore, Giovanni [Idaho National Laboratory; Novascone, Stephen Rhead [Idaho National Laboratory; Hales, Jason Dean [Idaho National Laboratory; Williamson, Richard L [Idaho National Laboratory; Martineau, Richard Charles [Idaho National Laboratory

    2016-06-01

    An in-reactor experiment is being designed in order to validate the pellet-cladding mechanical interaction (PCMI) behavior of the BISON fuel performance code. The experimental parameters for the test rod being placed in the Halden Research Reactor are being determined using BISON simulations. The 3D model includes a missing pellet surface (MPS) defect to generate large local cladding deformations, which should be measureable after typical burnup times. The BISON fuel performance code is being developed at Idaho National Laboratory (INL) and is built on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. BISON supports both 2D and 3D finite elements and solves the fully coupled equations for solid mechanics, heat conduction and species diffusion. A number of fuel performance effects are included using models for swelling, densification, creep, relocation and fission gas production & release. In addition, the mechanical and thermal contact between the fuel and cladding is explicitly modelled using a master-slave based contact algorithm. In order to accurately predict PCMI effects, the BISON code includes the relevant physics involved and provides a scalable and robust solution procedure. The depth of the proposed MPS defect is being varied in the BISON model to establish an optimum value for the experiment. The experiment will be interrupted approximately every 6 months to measure cladding radial deformation and provide data to validate BISON. The complete rodlet (~20 discrete pellets) is being simulated using a 180° half symmetry 3D model with MPS defects at two axial locations. In addition, annular pellets will be used at the top and bottom of the pellet stack to allow thermocouples within the rod to measure the fuel centerline temperature. Simulation results will be presented to illustrate the expected PCMI behavior and support the chosen experimental design parameters.

  10. Fabrication and Quality Inspection of U-10wt.%Zr Fuel Rod for Irradiation Test

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Hwan; Song, Hoon; Oh, Seok Jin; Lee, Jung Won; Park, Jeong Yong; Lee, Chan Bock [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    Metallic fuel has advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant and inherent passive safety. Metal fuels such as U-Zr alloy have been considered as a starting driver fuel for a proto-type Gen-IV sodium cooled fast reactor (PGSFR) in Korea. To confirm the design and fabrication technologies of metallic fuels with FMS cladding for the loading of metallic fuel in PGSFR, an irradiation test will be performed in BOR-60 in Russia in 2016. In this study, U-10wt.%Zr fuel rods using low enrichment uranium (LEU) have been fabricated and inspected in quality for the fuel verification of PGSFR. Fuel slugs per melting batch without casting defects were fabricated by development of the advanced casting technology and evaluation tests. The optimal GTAW welding conditions and parameters were also established through lots of experiments. And, the qualification test carried out to prove the weld quality of end plug welding of the metallic fuel rods. The wire wrapping of metallic fuel rods for the irradiation test was successfully accomplished in KAERI. So, PGSFR fuel rods for the irradiation test in BOR-60 have been soundly fabricated in KAERI.

  11. Test Methodology of Reproducing Fuel Rod Failure by Debris Fretting Wear

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Oh Joon; Park, Nam Gyu; Kim, Jae Ik [KEPCO NF, Daejeon (Korea, Republic of)

    2015-10-15

    A test was conducted with simple debris to reproduce debris fretting wear. 68% of fuel rod cladding thickness is worn out by Inconel debris in 75 hours. The test result shows that a simple link system is useful to accommodate debris oscillation, and mid grid mixing vanes could be a source of debris forcing. Additional tests will be conducted with various debris such as wire brush, metal chip, etc which are suspected to generate actual debris fretting wear in future works. Debris fretting is one of the most common cause of the nuclear fuel rod failure. Even the most of the nuclear fuels has debris protection system, debris still cause fuel rod failure. From 1994 to 2006, debris fretting failure is around 11% of the total fuel failure. In 2006-2010, the portion of debris rises to over 13%. The total number of fuel rods failure is decreasing, but the portion of the debris fretting wear is growing with time. Therefore reproducing and identifying the mechanism of fuel rod failure by debris fretting wear is needed to improve reliability of the nuclear fuel.

  12. Thorium utilisation in a small long-life HTR. Part III: Composite-rod fuel blocks

    Energy Technology Data Exchange (ETDEWEB)

    Verrue, Jacques, E-mail: jacques.verrue@polytechnique.org [Delft University of Technology, Reactor Institute Delft, Mekelweg 15, 2629 JB Delft (Netherlands); École Polytechnique (Member of ParisTech), 91128 Palaiseau Cedex (France); Ding, Ming, E-mail: dingm2005@gmail.com [Delft University of Technology, Reactor Institute Delft, Mekelweg 15, 2629 JB Delft (Netherlands); Harbin Engineering University, Nantong Street 145, 150001 Harbin (China); Kloosterman, Jan Leen, E-mail: j.l.kloosterman@tudelft.nl [Delft University of Technology, Reactor Institute Delft, Mekelweg 15, 2629 JB Delft (Netherlands)

    2014-02-15

    Highlights: • Composite-rod fuel blocks are proposed for a small block-type HTR. • An axial separation of fuel compacts is the most important feature. • Three patterns are presented to analyse the effects of the spatial distribution. • The spatial distribution has a large influence on the neutron spectrum. • Composite-rod fuel blocks reach a reactivity swing less than 4%. - Abstract: The U-Battery is a small long-life high temperature gas-cooled reactor (HTR) with power of 20 MWth. In order to increase its lifetime and diminish its reactivity swing, the concept of composite-rod fuel blocks with uranium and thorium was investigated. Composite-rod fuel blocks feature a specific axial separation between UO{sub 2} and ThO{sub 2} compacts in fuel rods. The design parameters, investigated by SCALE 6, include the number and spatial distribution of fuel compacts within the rods, the enrichment of uranium, the radii of fuel kernels and fuel compacts, and the packing fractions of uranium and thorium TRISO particles. The analysis shows that a lower moderation ratio and a larger inventory of heavy metals results in a lower reactivity swing. The optimal atomic carbon-to-heavy metal ratio depends on the mass fraction of U-235 and is commonly in the 160–200 range. The spatial distribution of the fuel compacts within the fuel rods has a large influence on the energy spectrum in each fuel compact and thus on the beginning-of-life reactivity and the reactivity swing. At end-of-life, the differences caused by the spatial distribution of the fuel compacts are smaller due to the fissions of U-233 in the ThO{sub 2} fuel compacts. This phenomenon enables to design fuel blocks with a very low reactivity swing, down to less than 4% in a 10-year lifetime. Among three types of thorium fuelled U-Battery blocks, the composite-rod fuel block achieves the highest end-of-life reactivity and the lowest reactivity swing.

  13. Development and control of the process for the manufacture of zircaloy-4 tubing for LWBR fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Eyler, J.H.

    1981-01-01

    The technical requirements for the Light Water Breeder Reactor (LWBR) fuel elements (fuel rods) imposed certain unique requirements for the low hafnium Zircaloy-4 tubing used as fuel rod cladding. This report describes, in detail, the tube manufacturing process, the product and process controls used, the inspections and tests performed, and the efforts involved in refining a commercial tube reducing process to produce tubes that would satisfy the requirements for LWBR fuel rod cladding.

  14. Technical Development of the Small Fission Gas Measurement in Fuel Rods using the Laser Puncturing

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Heemoon; Baik, Seungje; Jin, Younggwan; Jung, Yanghong; Yoo, Boungok; Ahn, Sangbok; Yang, Yongsik; Lee, Byoungoon

    2013-12-15

    Information of fuel cladding tube and expected gas amount were obtained from fuel development department to design chamber volume and specification of laser device. Laser puncturing tests for several tubes were performed to setup power and capability. Laser puncturing tests for several tubes were performed to setup power and capability. Vacuum system with chamber was established. Additionally, QMS(Quadruple Mass Spectrometer in high vacuum state) was installed in vacuum system. The system was installed in hotcell following the preliminary test for the puncturing, pressure measuring and gas content analysis. After system test was installed in hotcell following the preliminary test for the puncturing, pressure measuring and gas content analysis. After system test was completed, SFR fuel rods were punctured to measure total gas amount and each gas content(He, Xe, Kr). The system for laser puncturing and measurement of small fission gas amout in fuel rod was designed with considering hotcell facility and fuel rod condition for first year. Chamber size, laser capability were well operated and the system showed reasonable results. In second year, QMS(Quadruple Mass Spectrometer) was installed in the system for quantitative analysis of gas contents. Thus, Laser puncturing, amount of gas measurement and gas analysis were carried out in one time. The system was activated for SFR fuel rods after installation and preliminary test. 9 SFR fuel rods were tested and produced total gas amounts and gas analysis data(He, Xe, Kr)

  15. Fuel rod model based on Non-Fourier heat conduction equation

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa-Paredes, G. [Area de Ingenieria en Recursos Energeticos, Universidad Autonoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, Mexico DF., CP 09340 (Mexico)], E-mail: gepe@xanum.uam.mx; Espinosa-Martinez, E-G. [Retorno Quebec 6, Col. Burgos de Cuernavaca 62580, Temixco, Mor. (Mexico)

    2009-05-15

    In this paper we explore the applicability of a fuel rod mathematical model based on Non-Fourier transient heat conduction as constitutive law for the Light Water Reactors transient analysis (LWRs). In the classical theory of diffusion, Fourier law of heat conduction is used to describe the relation between the heat flux vector and the temperature gradient assuming that the heat propagation speeds are infinite. The motivation for this research was to eliminate the paradox of an infinite thermal wave speed. The time-dependent heat sources were considered in the fuel rod heat transfer model. The close of the Main Steam Isolated Valves (MSIV) transient in a Boiling Water Reactor (BWR) was analyzed by different relaxation times. The results show that for long-times the heat fluxes on the clad surface under Non-Fourier approach can be important, while for short-times and from the engineering point of view the changes are very small. Some results from transient calculations are examined.

  16. Detection of the Departure from Nucleate Boiling in Nuclear Fuel Rod Simulators

    Directory of Open Access Journals (Sweden)

    Amir Zacarias Mesquita

    2013-01-01

    Full Text Available In the thermal hydraulic experiments to determin parameters of heat transfer where fuel rod simulators are heated by electric current, the preservation of the simulators is essential when the heat flux goes to the critical point. One of the most important limits in the design of cooling water reactors is the condition in which the heat transfer coefficient by boiling in the core deteriorates itself. The heat flux just before deterioration is denominated critical heat flux (CHF. At this time, the small increase in heat flux or in the refrigerant inlet temperature at the core, or the small decrease in the inlet flux of cooling, results in changes in the heat transfer mechanism. This causes increases in the surface temperature of the fuel elements causing failures at the fuel (burnout. This paper describes the experiments conducted to detect critical heat flux in nuclear fuel element simulators carried out in the thermal-hydraulic laboratory of Nuclear Technology Development Centre (CDTN. It is concluded that the use of displacement transducer is the most efficient technique for detecting critical heat flux in nuclear simulators heated by electric current in open pool.

  17. Assessment of stainless steel 348 fuel rod performance against literature available data using TRANSURANUS code

    Directory of Open Access Journals (Sweden)

    Giovedi Claudia

    2016-01-01

    Full Text Available Early pressurized water reactors were originally designed to operate using stainless steel as cladding material, but during their lifetime this material was replaced by zirconium-based alloys. However, after the Fukushima Daiichi accident, the problems related to the zirconium-based alloys due to the hydrogen production and explosion under severe accident brought the importance to assess different materials. In this sense, initiatives as ATF (Accident Tolerant Fuel program are considering different material as fuel cladding and, one candidate is iron-based alloy. In order to assess the fuel performance of fuel rods manufactured using iron-based alloy as cladding material, it was necessary to select a specific stainless steel (type 348 and modify properly conventional fuel performance codes developed in the last decades. Then, 348 stainless steel mechanical and physics properties were introduced in the TRANSURANUS code. The aim of this paper is to present the obtained results concerning the verification of the modified TRANSURANUS code version against data collected from the open literature, related to reactors which operated using stainless steel as cladding. Considering that some data were not available, some assumptions had to be made. Important differences related to the conventional fuel rods were taken into account. Obtained results regarding the cladding behavior are in agreement with available information. This constitutes an evidence of the modified TRANSURANUS code capabilities to perform fuel rod investigation of fuel rods manufactured using 348 stainless steel as cladding material.

  18. MATPRO: a handbook of materials properties for use in the analysis of light water reactor fuel rod behavior

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, P.E.; Thompson, L.B. (eds.)

    1976-02-01

    This handbook describes the materials properties correlations and computer subcodes (MATPRO) developed for use with various LWR fuel rod behavior analytical programs at the Idaho National Engineering Laboratory. Documentation and formulations that are generally semiempirical in nature are presented for uranium dioxide and mixed uranium-plutonium dioxide fuel, zircaloy cladding, gas mixture, and LWR fuel rod material properties.

  19. Inspection of domestic nuclear fuel rods using neutron radiography at the Tehran research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Dastjerdi, Mohammad Hosein Choopan; Khalafi, Hossein; Kasesaz, Yaser [Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of); Movafeghi, Amir

    2016-11-01

    Three unused domestic fuel rods were investigated qualitatively and quantitatively by means of thermal neutron radiography. The neutron radiography tests were performed by the image plate method at Tehran research reactor in order to check the fuel properties. The pellets of these three fuel rods contained three different U-235 enrichments and different sizes that were filled into a zircalloy tube. In the qualitative investigations, the difference in size and enrichment between the pellets and the gaps between them were obviously recognized in the image of the fuel rods. In the quantitative investigations, data of the pellets compositions, their sizes (lengths and diameters) and the gaps between them were extracted from obtained images. It was found that the measured data and the manufacturer's specifications are in good agreement.

  20. Isotopic Details of the Spent Catawba-1 MOX Fuel Rods at ORNL

    Energy Technology Data Exchange (ETDEWEB)

    Ellis, Ronald James [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-04-01

    The United States Department of Energy funded Shaw/AREVA MOX Services LLC to fabricate four MOX Lead Test Assemblies (LTA) from weapons-grade plutonium. A total of four MOX LTAs (including MX03) were irradiated in the Catawba Nuclear Station (Unit 1) Catawba-1 PWR which operated at a total thermal power of 3411 MWt and had a core with 193 total fuel assemblies. The MOX LTAs were irradiated along with Duke Energy s irradiation of eight Westinghouse Next Generation Fuel (NGF) LEU LTAs (ref.1) and the remaining 181 LEU fuel assemblies. The MX03 LTA was irradiated in the Catawba-1 PWR core (refs.2,3) during cycles C-16 and C-17. C-16 began on June 5, 2005, and ended on November 11, 2006, after 499 effective full power days (EFPDs). C-17 started on December 29, 2006, (after a shutdown of 48 days) and continued for 485 EFPDs. The MX03 and three other MOX LTAs (and other fuel assemblies) were discharged at the end of C-17 on May 3, 2008. The design of the MOX LTAs was based on the (Framatome ANP, Inc.) Mark-BW/MOX1 17 17 fuel assembly design (refs. 4,5,6) for use in Westinghouse PWRs, but with MOX fuel rods with three Pu loading ranges: the nominal Pu loadings are 4.94 wt%, 3.30 wt%, and 2.40 wt%, respectively, for high, medium, and low Pu content. The Mark-BW/MOX1 (MOX LTA) fuel assembly design is the same as the Advanced Mark-BW fuel assembly design but with the LEU fuel rods replaced by MOX fuel rods (ref. 5). The fabrication of the fuel pellets and fuel rods for the MOX LTAs was performed at the Cadarache facility in France, with the fabrication of the LTAs performed at the MELOX facility, also in France.

  1. Sliding Wear and Friction Behavior of Fuel Rod Material in Water and Dry State

    Science.gov (United States)

    Park, Jin Moo; Kim, Jae Hoon; Jeon, Kyeong Lak; Park, Jun Kyu

    In water cooled reactors, the friction between spacer grid and fuel rod can lead to severe wear and it is an important topic to study. In the present study, sliding wear behavior of zirconium alloy was investigated in water and dry state using the pin-on-disc sliding wear tester. Sliding wear resistance of zirconium alloy against heat treated inconel alloy was examined at room temperature. The parameters in this study were sliding velocity, axial load and sliding distance. The wear characteristics of zirconium alloy was evaluated by friction coefficient, specific wear rate and wear volume. The micro-mechanisms responsible for wear in zirconium alloy were identified to be micro-cutting, micro-pitting, delamination and micro-cracking of deformed surface zone.

  2. Experimental Investigation on Flow-Induced Vibration of Fuel Rods in Supercritical Water Loop

    Directory of Open Access Journals (Sweden)

    Licun Wu

    2014-01-01

    Full Text Available The supercritical water-cooled reactor (SCWR is one of the most promising Generation IV reactors. In order to make the fuel qualification test for SCWR, a research plan is proposed to test a small scale fuel assembly in a supercritical water loop. To ensure the structure safety of fuel assembly in the loop, a flow-induced vibration experiment was carried out to investigate the vibration behavior of fuel rods, especially the vibration caused by leakage flow. From the experiment result, it can be found that: the vibration of rods is mainly caused by turbulence when flow rate is low. However, the effects of leakage flow become obvious as flow rate increases, which could changes the distribution of vibrational energy in spectrum, increasing the vibrational energy in high-frequency band. That is detrimental to the structure safety of fuel rods. Therefore, it is more reasonable to improve the design by using the spacers with blind hole, which can eliminate the leakage flow, to assemble the fuel rods in supercritical water loop. On the other hand, the experimental result could provide a benchmark for the theoretical studies to validate the applicability of boundary condition set for the leakage-flow-induced vibration.

  3. Radial power density distribution of MOX fuel rods in the IFA-651

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Byung Ho; Koo, Yang Hyun; Joo, Hyung Kook; Cheon, Jin Sik; Oh, Je Yong; Sohn, Dong Seong [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2002-04-01

    Two MOX fuel rods, which were fabricated in the Paul Scherrer Institute (PSI), Switzerland in cooperation with Korea Atomic Energy Research Institute, have been irradiated in the HBWR from June, 2000 in the framework of OECD-HRP together with a reference MOX fuel rod supplied by the BNFL. Since fuel temperature, which is influenced by radial power distribution, is basic in analyzing fuel behavior, it is required to consider radial power distribution in the HBWR. A subroutine FACTOR{sub H}BWR that calculates radial power density distribution for three MOX fuel rods has been developed based on neutron physics results and DEPRESS program. The developed subroutine FACTOR{sub H}BWR gives good agreement with the physics calculation except slight under-prediction at the outer part of the pellet above the burnup of 20 MWd/kgHM. The subroutine will be incorporated into a computer code COSMOS and used to analyze the in-reactor behavior of the three MOX fuel rods during the Halden irradiation test. 24 figs., 4 tabs. (Author)

  4. FRAPCON-3: Modifications to fuel rod material properties and performance models for high-burnup application

    Energy Technology Data Exchange (ETDEWEB)

    Lanning, D.D.; Beyer, C.E.; Painter, C.L.

    1997-12-01

    This volume describes the fuel rod material and performance models that were updated for the FRAPCON-3 steady-state fuel rod performance code. The property and performance models were changed to account for behavior at extended burnup levels up to 65 Gwd/MTU. The property and performance models updated were the fission gas release, fuel thermal conductivity, fuel swelling, fuel relocation, radial power distribution, solid-solid contact gap conductance, cladding corrosion and hydriding, cladding mechanical properties, and cladding axial growth. Each updated property and model was compared to well characterized data up to high burnup levels. The installation of these properties and models in the FRAPCON-3 code along with input instructions are provided in Volume 2 of this report and Volume 3 provides a code assessment based on comparison to integral performance data. The updated FRAPCON-3 code is intended to replace the earlier codes FRAPCON-2 and GAPCON-THERMAL-2. 94 refs., 61 figs., 9 tabs.

  5. Finite-element procedure for calculating the three-dimensional inelastic bowing of fuel rods (AWBA development program)

    Energy Technology Data Exchange (ETDEWEB)

    Martin, S E

    1982-05-01

    An incremental finite element procedure is developed for calculating the in-pile lateral bowing of nuclear fuel rods. The fuel rod is modeled as a viscoelastic beam whose material properties are derived as perturbations of the results of an axisymmetric stress analysis of the fuel rod. The effects which are taken into account in calculating the rod's lateral bowing include: (a) lateral, axial, and rotational motions and forces at the rod supports, (b) transverse gradients of temperature, fast-neutron flux, and fissioning rate, and (c) cladding circumferential wall thickness variation. The procedure developed in this report could be used to form the basis for a computer program to calculate the time-dependent bowing as a function of the fuel rod's operational and environmental history.

  6. Fretting wear behavior of Cr-coated fuel rod for accident-tolerant fuel in flowing fluid

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Young Ho; Kim, Hyung Kyu; Kim, Hyun Gil; Koo, Yang Hyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Fretting wear test of the Cr-coated fuel clading candidate have been performed in the flowing fluid condition in order to verify the reliability of Cr-coated layer on zirconium-based fuel cladding. Rod wear volume at each grid spring and dimple is dramaically increased with GTR gap even though each wear scar is not evenly distributed within a 1x1 grid cell.

  7. Experience with incomplete control rod insertion in fuel with burnup exceeding approximately 40 GWD/MTU

    Energy Technology Data Exchange (ETDEWEB)

    Kee, E. [Houston Lighting & Power Co., Wadworth, TX (United States)

    1997-01-01

    Analysis and measurement experience with fuel assemblies having incomplete control rod insertion at burnups of approximately 40 GWD/MTU is presented. Control rod motion dynamics and simplified structural analyses are presented and compared to measurement data. Fuel assembly growth measurements taken with the plant Refueling Machine Z-Tape are described and presented. Bow measurements (including plug gauging) are described and potential improvements are suggested. The measurements described and analysis performed show that sufficient guide tube bow (either from creep or yield buckling) is present in some high burnup assemblies to stop the control rods before they reach their full limit of travel. Recommendations are made that, if implemented, could improve cost performance related to testing and analysis activities.

  8. NDT of the fuel rods with artificial defect

    Energy Technology Data Exchange (ETDEWEB)

    Yang, S.Y.; Min, D.K.; Eom, S.H.; Chun, Y.B.; Min, D.K

    2000-07-01

    Non-destructive examination such as visual inspection, dimensional measurement, eddy current and gamma scanning have been carried out. The objective of this study is to evaluate the characteristics of spent fuels, and to obtain the basic technical data through the study of long term storage behavior of spent fuels. In the results of visual inspection, there is no observable effects around the part of artificial defect. And there is nothing unusual in the results of gamma scanning. Diameter and ovality the artificial defect were measured. The result obtained from this study will be used as a basic data for the study of behavior for spent fuel under the long term storage condition and the safety evaluation of spent fuel.

  9. Design of Testing Set-up for Nuclear Fuel Rod by Neutron Radiography at CARR

    Institute of Scientific and Technical Information of China (English)

    WEI; Guo-hai; HAN; Song-bai; WANG; Hong-li; HAO; Li-jie; WU; Mei-mei; HE; Lin-feng; WANG; Yu; LIU; Yun-tao; SUN; Kai; CHEN; Dong-feng

    2012-01-01

    <正>An experimental set-up dedicated to non-destructively test a 15 cm long pressurized water reactor (PWR) nuclear fuel rod by neutron radiography (NR) is designed and fabricated. It consists of three parts: Transport container, imaging block and steel support. The design of the transport container was optimized with Monte-Carlo simulation by the MCNP code.

  10. Investigation of water films on fuel rods in boiling water reactors using neutron tomography

    Energy Technology Data Exchange (ETDEWEB)

    Lanthen, Jonas

    2006-09-15

    In a boiling water reactor, thin films of liquid water around the fuel rods play a very important role in cooling the fuel, and evaporation of the film can lead to fuel damage. If the thickness of the water film could be measured accurately the reactor operation could be both safer and more economical. In this thesis, the possibility to use neutron tomography, to study thin water films on fuel rods in an experimental nuclear fuel set-up, has been investigated. The main tool for this has been a computer simulation software. The simulations have shown that very thin water films, down to around 20 pm, can be seen on fuel rods in an experimental set-up using neutron tomography. The spatial resolution needed to obtain this result is around 300 pm. A suitable detector system for this kind of experiment would be plastic fiber scintillators combined with a CCD camera. As a neutron source it would be possible to use a D-D neutron generator, which generates neutrons with energies of 2.5 MeV. Using a neutron generator with a high enough neutron yield and a detector with high enough detection efficiency, a neutron tomography to measure thin water films should take no longer than 25 - 30 minutes.

  11. Analysis of high burnup fuel behavior under control rod ejection accident in Korea standard nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chan Bok; Lee, Chung Chan; Kim, Oh Hwan; Kim, Jong Jin [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1996-07-01

    Test results of high burnup fuel behavior under RIA(reactivity insertion accident) indicated that fuel might fail at the fuel enthalpy lower than that in the current fuel failure criteria was derived by the conservative assumptions and analysis of fuel failure mechanisms, and applied to the analysis of control rod ejection accident in the 1,000 MWe Korea standard PWR. Except that three dimensional core analysis was performed instead of conventional zero dimensional analysis, all the other conservative assumptions were kept. Analysis results showed that less than on percent of the fuel rods in the core has failed which was much less than the conventional fuel failure fraction, 9.8 %, even though a newly derived fuel failure criteria -Fuel failure occurs at the power level lower than that in the current fuel failure criteria. - was applied, since transient fuel rod power level was significantly decreased by analyzing the transient fuel rod power level was significantly decreased by analyzing the transient core three dimensionally. Therefore, it can be said that results of the radiological consequence analysis for the control rod ejection accident in the FSAR where fuel failure fraction was assumed 9.8 % is still bounding. 18 tabs., 48 figs., 39 refs. (Author).

  12. Acceleration Test Method for Failure Prediction of the End Cap Contact Region of Sodium Cooled Fast Reactor Fuel Rod

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyung-Kyu; Lee, Young-Ho; Lee, Hyun-Seung; Lee, Kang-Hee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2017-05-15

    This paper reports the results of an acceleration test to predict the contact-induced failure that could occur at the cylinder-to-hole joint for the fuel rod of a sodium-cooled fast reactor (SFR). To incorporate the fuel life of the SFR currently under development at KAERI (around 35,000 h), the acceleration test method of reliability engineering was adopted in this work. A finite element method was used to evaluate the flow-induced vibration frequency and amplitude for the test parameter values. Five specimens were tested. The failure criterion during the life of the SFR fuel was applied. The S-N curve of the HT-9, the material of concern, was used to obtain the acceleration factor. As a result, a test time of 16.5 h was obtained for each specimen. It was concluded that the B{sub 0.004} life would be guaranteed for the SFR fuel rods with 99% confidence if no failure was observed at any of the contact surfaces of the five specimens.

  13. Development of the vibration analysis technique of fuel rod and research on the methodology of fuel fretting wear analysis

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Heung Seok; Kim, Kyung Kyu; Yoon, Hyung Hoo; Song, Ki Nam

    1998-12-01

    The FEM program has been developed to predict the natural frequencies, the FEM program has been developed to predict the natural frequencies, and mode shapes of fuel rod subjected to axial force and continuously supported by a rotational and vent spring system, and to calculate the minimum reaction forces of the spacer grid spring when the maximum vibration amplitude of fuel rod is known. This program has been verified by commercial ANSYS program and the vibration test of dummy rods in air. The test equipment were set to get the fifth modes of test rods. Partial slip problem has been studied for the analysis of fuel fretting problem. Firstly, the assumption of semi-infiniteness of the contact bodies were validated by finite element (FE) analysis. From FE results, a classical bodies were validated by finite element (FE) analysis. From FE results, aclassical theory of elasticity was utilized with regarding the problem as a plane problem. Secondly, the Mindlin-Cattaneo problem was re-evaluated, which gave the fundamental idea for developing the numerical tool for the shear traction on the contact. Shear force of sequentially-changing directions was considered and the corresponding shear traction was evaluated by extending the numerical tool for the Mindlin-Cattaneo problem.

  14. Fuel enrichment and temperature distribution in nuclear fuel rod in (D-T) driven hybrid reactor system

    Energy Technology Data Exchange (ETDEWEB)

    Osman, Ypek [Suleyman Demirel Universitesi Muhendislik-Mimarlyk Fakultesi, Isparta (Turkey)

    2001-07-01

    In this study, melting point of the fuel rod and temperature distribution in nuclear fuel rod are investigated for different coolants under various first wall loads (P{sub w}, =5, 6, 7, 8, 9, and 10 MWm{sup -2}) in Fusion-Fission reactor fueled with 50%LWR +50%CANDU. The fusion source of neutrons of 14.1 MeV is simulated by a movable target along the main axis of cylindrical geometry as a line source. In addition, the fusion chamber was thought as a cylindrical cavity with a diameter of 300 cm that is comparatively small value. The fissile fuel zone is considered to be cooled with four different coolants, gas, flibe (Li{sub 2}BeF{sub 4}), natural lithium (Li), and eutectic lithium (Li{sub 17}Pb{sub 83}). Investigations are observed during 4 years for discrete time intervals of{delta}t= 0.5 month and by a plant factor (PF) of 75%. Volumetric ratio of coolant-to fuel is 1:1, 45.515% coolant, 45.515% fuel, 8.971% clad, in fuel zone. (author)

  15. Characterization of Suspect Fuel Rod Pieces from the 105 K West Basin

    Energy Technology Data Exchange (ETDEWEB)

    Delegard, Calvin H.; Schmidt, Andrew J.; Pool, Karl N.; Thornton, Brenda M.

    2006-09-15

    This report provides physical and radiochemical characterization results from examinations and laboratory analyses performed on ~0.55-inch diameter rod pieces found in the 105 K West (KW) Basin that were suspected to be from nuclear reactor fuel. The characterization results will be used to establish the technical basis for adding this material to the contents of one of the final Multi-Canister Overpacks (MCOs) that will be loaded out of the KW Basin in late FY2006 or at a later time depending on project priorities. Fifteen fuel rod pieces were found during the clean out of the KW Basin. Based on lack of specific credentials, documentation, or obvious serial numbers, none of the items could be positively identified nor could their sources or compositions be described. Item weights and dimensions measured in the KW Basin indicated densities consistent with the suspect fuel rods containing uranium dioxide (UO2), uranium metal, or being empty. Extensive review of the Hanford Site technical literature led to the postulation that these pieces likely were irradiated test fuel prepared to support of the development of the Hanford “New Production Reactor,” later called N Reactor. To obtain definitive data on the composition of the suspect fuel, 4 representative fuel rod pieces, with densities corresponding to oxide fuel were selected from the 15 items, and shipped from the KW Basin to the Pacific Northwest National Laboratory’s (PNNL) Radiological Processing Laboratory (RPL; also known at the 325 Building) for examinations and characterization. The three fuel rod that were characterized appear to contain slightly irradiated UO2 fuel, originally of natural enrichment, with zirconium cladding. The uranium-235 isotopic concentrations decreased by the irradiation and become slightly lower than the natural enrichment of 0.72% to range from 0.67 to 0.71 atom%. The plutonium concentrations, ranged from about 200 to 470 grams per metric ton of uranium and ranged in Plutonium

  16. Characterization of Suspect Fuel Rod Pieces from the 105 K West Basin

    Energy Technology Data Exchange (ETDEWEB)

    Delegard, Calvin H.; Schmidt, Andrew J.; Pool, Karl N.; Thornton, Brenda M.

    2006-07-25

    This report provides physical and radiochemical characterization results from examinations and laboratory analyses performed on {approx}0.55-inch diameter rod pieces found in the 105 K West (KW) Basin that were suspected to be from nuclear reactor fuel. The characterization results will be used to establish the technical basis for adding this material to the contents of one of the final Multi-Canister Overpacks (MCOs) that will be loaded out of the KW Basin in late FY2006 or at a later time depending on project priorities. Fifteen fuel rod pieces were found during the clean out of the KW Basin. Based on lack of specific credentials, documentation, or obvious serial numbers, none of the items could be positively identified nor could their sources or compositions be described. Item weights and dimensions measured in the KW Basin indicated densities consistent with the suspect fuel rods containing uranium dioxide (UO2), uranium metal, or being empty. Extensive review of the Hanford Site technical literature led to the postulation that these pieces likely were irradiated test fuel prepared to support of the development of the Hanford ''New Production Reactor'', later called N Reactor. To obtain definitive data on the composition of the suspect fuel, 4 representative fuel rod pieces, with densities corresponding to oxide fuel were selected from the 15 items, and shipped from the KW Basin to the Pacific Northwest National Laboratory's (PNNL) Radiological Processing Laboratory (RPL; also known at the 325 Building) for examinations and characterization. The three fuel rod that were characterized appear to contain slightly irradiated UO2 fuel, originally of natural enrichment, with zirconium cladding. The uranium-235 isotopic concentrations decreased by the irradiation and become slightly lower than the natural enrichment of 0.72% to range from 0.67 to 0.71 atom%. The plutonium concentrations, ranged from about 200 to 470 grams per metric ton of

  17. Rod internal pressure of spent nuclear fuel and its effects on cladding degradation during dry storage

    Science.gov (United States)

    Kim, Ju-Seong; Hong, Jong-Dae; Yang, Yong-Sik; Kook, Dong-Hak

    2017-08-01

    Temperature and hoop stress limits have been used to prevent the gross rupture of spent nuclear fuel during dry storage. The stress due to rod internal pressure can induce cladding degradation such as creep, hydride reorientation, and delayed hydride cracking. Creep is a self-limiting phenomenon in a dry storage system; in contrast, hydride reorientation and delayed hydride cracking are potential degradation mechanisms activated at low temperatures when the cladding material is brittle. In this work, a conservative rod internal pressure and corresponding hoop stress were calculated using FRAPCON-4.0 fuel performance code. Based on the hoop stresses during storage, a study on the onset of hydride reorientation and delayed hydride cracking in spent nuclear fuel was conducted under the current storage guidelines. Hydride reorientation is hard to occur in most of the low burn-up fuel while some high burn-up fuel can experience hydride reorientation, but their effect may not be significant. On the other hand, delayed hydride cracking will not occur in spent nuclear fuel from pressurized water reactor; however, there is a lack of confirmatory data on threshold intensity factor for delayed hydride cracking and crack size distribution in the fuel.

  18. On-line fuel and control rod integrity surveillance in BWRs

    Energy Technology Data Exchange (ETDEWEB)

    Sihver, L.; Larsson, I. [CHalmers Univ. of Technology, Nuclear Engineering, Gothenberg (Sweden); Loner, H. [Kernkraftwerk Leibstadt, Leibstadt (Switzerland); Grundin, A.; Helmersson, J-O.; Ledergerber, G. [Forsmarks Kraftgrupp AB, Osthammar (Sweden)

    2013-07-01

    Surveillance of fuel and control rod integrity in a BWR core is essential to maintain a safe and reliable operation of the nuclear power plant. Any actions to be taken in the event of a fuel failure during reactor operation should be based on the best available information regarding the failure and expected consequences. The detection of fuel and control rod failures in BWRs is usually performed by analyzing samples of off-gases and coolant taken with a certain time intervals, e.g. once a week or once a month. This procedure can, however, leave the failure undetected in the core for quite some time. Therefore, a sufficient improvement of the surveillance of fuel and control rods can be achieved by simultaneous measurements of He and gamma emitting noble gases on-line in the off gas system. In this paper, experiences of such measurements performed at Kernkraftwerk Leibstadt (KKL) in Switzerland and Forsmark nuclear power plant (NPP) in Sweden will be presented. (author)

  19. Development of a program for the analysis on the free vibration of a fuel rod and its application

    Energy Technology Data Exchange (ETDEWEB)

    Sohn, Dong Seung; Yim, Jeong Sik [Korea Atomic Energy Research Institute, Taejon (Korea)

    1998-12-01

    Commercial Nuclear fuel burns more than 2 or three years in a core and it is essential that the fuels have a integrity without any failures during the burnup period. The factors that influence on the fuel integrity are classified as nuclear, mechanical, thermal and material factors and they are inter-related with complexity. Since the final integrity should be assured mechanically, the evaluation of the fuel rod mechanical integrity is important in a fuel design. The fuel rod for PWR is supported by spring of spacer grids to maintain its axial location and lateral space between fuel rods to get proper functions during the residence in a reactor. The long exposure duration makes the spring to be relax and loss the spring force that results in a fuel rod rattling which may cause fuel rod failure. The design criteria of the spring forces for various fuel vendors are similar each other but they are slightly different: require minimal spring force to prevent the spring from rattling at the end of life or the minimal gap between fuel rod and spring. However the spring force is relaxed due to the neutron irradiation and stress relaxation that suddenly decrease exponentially and the spring behave nonlinear by the initial spring deflection and the relaxation phenomenon. The objective of this study is to develop a finite element program to support the mechanical evaluation in view of the interaction between fuel rod and spacer spring. Here considering the spring behaviour as a function of burnup, the reaction forces of the springs are calculated by the finite element program, BEVIRA developed herein to aid the evaluation of the integrity of the fuel rod from fretting. A fuel rod is modelled as a beam to get natural frequencies and mode shapes supported by a rotational spring at each spacer spring. The results from the program are compared with previous data and those from ANSYS for the validation of the program and procedures. For the example calculation, the characteristics

  20. Build-up of actinides in irradiated fuel rods of the ET-RR-1 reactor

    Energy Technology Data Exchange (ETDEWEB)

    Adib, M.; Naguib, K.; Morcos, H.N

    2001-09-01

    The content concentrations of actinides are calculated as a function of operating reactor regime and cooling time at different percentage of fuel burn-up. The build-up transmutation equations of actinides content in an irradiated fuel are solved numerically .A computer code BAC was written to operate on a PC computer to provide the required calculations. The fuel element of 10% {sup 235}U enrichment of ET-RR-1 reactor was taken as an example for calculations using the BAC code. The results are compared with other calculations for the ET-RR-1 fuel rod. An estimation of fissile build-up content of a proposed new fuel of 20% {sup 235}U enrichment for ET-RR-1 reactor is given. The sensitivity coefficients of build-up plutonium concentrations as a function of cross-section data uncertainties are also calculated.

  1. Surface properties of sprayed and electrodeposited ZnO rod layers

    Science.gov (United States)

    Gromyko, I.; Krunks, M.; Dedova, T.; Katerski, A.; Klauson, D.; Oja Acik, I.

    2017-05-01

    Herein we present a comparative study on as-deposited, two-month-stored, and heat-treated ZnO rods obtained by spray pyrolysis (SP) at 550 °C, and electrodeposition (ED) at 80 °C. The aim of the study is to establish the reason for different behaviour of wettability and photocatalytic activity (PA) of SP and ED rods. Samples were studied using XPS, SEM, XRD, Raman, contact angle (CA) measurements and photocatalytic oxidation of doxycycline. Wettability and PA are mainly controlled by surface composition rather than by morphology. The relative amount of hydroxyl groups on the surface of as-deposited ED rods is four times higher compared to as-deposited SP rods. Opposite to SP rods, ED rods contain oxygen vacancy defects (Vo). Therefore, as-deposited ED rods are superhydrophilic (CA ∼ 3°) and show highest PA among studied samples, being three times higher compared to SP rods (removing of 75% of doxycycline after 30 min). It was revealed that as-deposited ED rods are inclined to faster contamination. The amount of Cdbnd C groups on the surface of aged ED rods is six times higher compared to aged SP rods. Stored ED samples become hydrophobic (CA ∼ 120°) and PA decreases sharply while SP rods remain hydrophilic (CA ∼ 50°), being more resistive to the contamination.

  2. Licensing of spent fuel dry storage and consolidated rod storage: A Review of Issues and Experiences

    Energy Technology Data Exchange (ETDEWEB)

    Bailey, W.J.

    1990-02-01

    The results of this study, performed by Pacific Northwest Laboratory (PNL) and sponsored by the US Department of Energy (DOE), respond to the nuclear industry's recommendation that a report be prepared that collects and describes the licensing issues (and their resolutions) that confront a new applicant requesting approval from the US Nuclear Regulatory Commission (NRC) for dry storage of spent fuel or for large-scale storage of consolidated spent fuel rods in pools. The issues are identified in comments, questions, and requests from the NRC during its review of applicants' submittals. Included in the report are discussions of (1) the 18 topical reports on cask and module designs for dry storage fuel that have been submitted to the NRC, (2) the three license applications for dry storage of spent fuel at independent spent fuel storage installations (ISFSIs) that have been submitted to the NRC, and (3) the three applications (one of which was later withdrawn) for large-scale storage of consolidated fuel rods in existing spent fuel storage pools at reactors that were submitted tot he NRC. For each of the applications submitted, examples of some of the issues (and suggestions for their resolutions) are described. The issues and their resolutions are also covered in detail in an example in each of the three subject areas: (1) the application for the CASTOR V/21 dry spent fuel storage cask, (2) the application for the ISFSI for dry storage of spent fuel at Surry, and (3) the application for full-scale wet storage of consolidated spent fuel at Millstone-2. The conclusions in the report include examples of major issues that applicants have encountered. Recommendations for future applicants to follow are listed. 401 refs., 26 tabs.

  3. Comparison study of the thermal mechanical performance of fuel rods during BWR fuel preconditioning operations using the computer codes FUELSIM and FEMAXI-V

    Energy Technology Data Exchange (ETDEWEB)

    Pantoja C, R. [IPN, Escuela Superior de Fisica y Matematicas, Departamento de Ingenieria Nuclear, Av. Instituto Politecnico Nacional s/n, Col. San Pedro Zacatenco, 07738 Mexico D. F. (Mexico); Ortiz V, J.; Castillo D, R., E-mail: rafael.pantoja10@yahoo.com.m [ININ, Departamento de Sistemas Nucleares, Carretera Mexico-Toluca s/n, Ocoyoacac 52750, Estado de Mexico (Mexico)

    2010-10-15

    The safety of nuclear power plants requires monitoring those parameters having some direct or indirect effect on safety. The thermal limits are values set for those parameters considered having most impact on the safe operation of a nuclear power reactor. Some thermal limits monitoring requires the thermal-mechanical analysis of the rods containing the nuclear fuel. The fuel rod thermal-mechanical behaviour under irradiation is a complex process in which there exists a great deal of interrelated physical and chemical phenomena, so that the fuel rod performance analysis in the core of a nuclear power reactor is generally accomplished by using computer codes, which integrate several of the phenomena that are expected to occur during the lifetime of the fuel rod in the core. In the operation of a nuclear power reactor, pre-conditioning simulations are necessary to determine in advance limit values for the power that can be generated in a fuel rod during any power ramp, and mainly during reactor startup, and thus avoiding any rod damage. In this work, a first analysis of the thermal-mechanical performance of typical fuel rods used in nuclear reactors of the type BWR is performed. This study includes two types of fuel rods: one from a fuel assembly design with array 8 x 8, and the other one from a 10 x 10 fuel assembly design, and a comparison of the thermal-mechanical performance between the two different rod designs is performed. The performance simulations were performed by the code FUELSIM, and compared against results previously obtained from similar simulation with the code FEMAXI-V. (Author)

  4. On the Minimum Safety Factor in Elastic Buckling of Fuel Rod

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyung Kyu; Kim, Jae Yong; Yoon, Kyung Ho; Lee, Young Ho; Lee, Kang Hee; Kang, Heung Seok; Song, Kun Woo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2010-10-15

    Elastic buckling of a thin tube is an instantaneous collapse phenomenon due to an external pressure. This should be prohibited for a PWR (Pressurized Water Reactor) fuel rod. There is an engineering formula of it; however, safety factor used to be applied to the calculation results since there will be uncertainty in the parameters of the formulae such as dimensional tolerances, environmental conditions and so forth. It is a designer's responsibility to determine an appropriate safety factor that is acceptably economically conservative. Mechanical properties of a material are usually adopted from a material handbook. However, they are usually different from the measured values of the material actually used. A local dimension anomaly critically affects the elastic buckling. Conventional safety factors against the elastic buckling seemed to be large (more than 3.5). However, the reason for this is rarely found. Engineering experience may be incorporated. Therefore, it is highly necessary to propose a minimum safety factor on the elastic buckling while accommodating the above mentioned uncertainties. It is so especially for the dual cooled fuel rod since it has never been used before. The primary purpose of this work is to quantify the aforementioned uncertainties of the parameters in the elastic buckling formula, especially for an outer cladding of the currently studied dual cooled fuel rod. It is extended from the previous theoretical and experimental study

  5. Feasibility study of on-line digital X-ray imaging for irradiated fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Parthoens, Y.; Gys, A. [Reactor Material Research Department, SCK-CEN, Mol (Belgium); Smolders, V. [Industrial Engineer Department, Katholieke Hogeschool Kempen, Geel (Belgium)

    2003-07-01

    At the Reactor Material Research Department of the Belgian Nuclear Research Centre SCK-CEN Xray imaging of the internal parts of irradiated fuel rods is done on silver-halide films using a 420 kV X-ray source. The replacement of the films by an on-line digital X-ray imaging system implies several advantages. Images can be evaluated instantly and source parameters can be optimized more easily. Time consuming film development is superfluous. The images can digitally be enhanced, processed, reported and archived. Within this work the feasibility of four commercial on-line digital X-ray imaging systems were studied for post-irradiation examination on fuel rods in a hot cell environment. The criteria to evaluate the systems were image quality, integration in the existing hot cell infrastructure, durability and cost price. For the evaluation and comparison of the image quality a simulation fuel rod was fabricated. Three systems suffered from lack of sensitivity, contrast and/or resolution. Only the CsI-scintillator coupled to a CCD-camera with image intensifier gave a sufficient image quality. On the other hand the image intensifiers' dimensions are difficult to integrate in the existing hot cell infrastructure. Also the durability of intensifier screens is questionable as they are susceptible to image burn. Smaller image intensifiers easier to integrate are commercial available nowadays.

  6. Research on Power Ramp Testing Method for PWR Fuel Rod at Research Reactor

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In order to develop high performance fuel assembly for domestic nuclear power plant, it is necessary to master some fundamental test technology. So the research on the power ramp testing methods is proposed. A tentative power ramp test for short PWR fuel rod has been conducted at the heavy water research reactor (HWRR) in China Institute of Atomic Energy (CIAE) in May of 2001. The in-pile test rig was placed into the central channel of the reactor . The test rig consists of pressure pipe assembly, thimble, solid neutron absorbing screen and its driving parts, etc.. The test

  7. Development of Application Technology of a Kagome Truss for a Fuel rod Support Structure

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Ki Ju; Lee, Byung Chul; Kim, Pan Su [Chonnam National University, Gwangju (Korea, Republic of)

    2010-05-15

    The purpose of this work is to design a Wire-woven Bulk Kagome (WBK) cellular metal for a fuel rod support structure of a dual cooled fuel and to fabricate test samples. Design of WBK-based support - To analyze dynamic characteristics of a support structure with WBK core under side impact. - To specify strength of WBK to be used for the support. - To design strut length and diameter of WBK. Fabrication of the test samples - To assemble WBK samples from helically formed wires. - To braze WBK samples with side straps

  8. Fission Gas Release in LWR Fuel Rods Exhibiting Very High Burn-Up

    DEFF Research Database (Denmark)

    Carlsen, H.

    1980-01-01

    Two UO2Zr BWR type test fuel rods were irradiated to a burn-up of about 38000 MWd/tUO2. After non-destructive characterization, the fission gas released to the internal free volume was extracted and analysed. The irradiation was simulated by means of the Danish fuel performance code WAFER-2, which...... uses an empirical gas release model combined with a strongly burn-up dependent correction term, developed by the US Nuclear Regulatory Commission. The paper presents the experimental results and the code calculations. It is concluded that the model predictions are in reasonable agreement (within 15...

  9. System analysis with improved thermo-mechanical fuel rod models for modeling current and advanced LWR materials in accident scenarios

    Science.gov (United States)

    Porter, Ian Edward

    A nuclear reactor systems code has the ability to model the system response in an accident scenario based on known initial conditions at the onset of the transient. However, there has been a tendency for these codes to lack the detailed thermo-mechanical fuel rod response models needed for accurate prediction of fuel rod failure. This proposed work will couple today's most widely used steady-state (FRAPCON) and transient (FRAPTRAN) fuel rod models with a systems code TRACE for best-estimate modeling of system response in accident scenarios such as a loss of coolant accident (LOCA). In doing so, code modifications will be made to model gamma heating in LWRs during steady-state and accident conditions and to improve fuel rod thermal/mechanical analysis by allowing axial nodalization of burnup-dependent phenomena such as swelling, cladding creep and oxidation. With the ability to model both burnup-dependent parameters and transient fuel rod response, a fuel dispersal study will be conducted using a hypothetical accident scenario under both PWR and BWR conditions to determine the amount of fuel dispersed under varying conditions. Due to the fuel fragmentation size and internal rod pressure both being dependent on burnup, this analysis will be conducted at beginning, middle and end of cycle to examine the effects that cycle time can play on fuel rod failure and dispersal. Current fuel rod and system codes used by the Nuclear Regulatory Commission (NRC) are compilations of legacy codes with only commonly used light water reactor materials, Uranium Dioxide (UO2), Mixed Oxide (U/PuO 2) and zirconium alloys. However, the events at Fukushima Daiichi and Three Mile Island accident have shown the need for exploration into advanced materials possessing improved accident tolerance. This work looks to further modify the NRC codes to include silicon carbide (SiC), an advanced cladding material proposed by current DOE funded research on accident tolerant fuels (ATF). Several

  10. A quantitative estimate on the heat transfer in cylindrical fuel rods to account for flux depression inside fuel

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Mario A.B. da; Narain, Rajendra; Vasconcelos, Wagner E. de, E-mail: narain@ufpe.b, E-mail: wagner@ufpe.b [Universidade Federal de Pernambuco (DEN/UFPE), Recife, PE (Brazil). Centro de Tecnologia e Geociencias. Dept. de Energia Nuclear

    2011-07-01

    In a nuclear reactor, the amount of power generation is limited by thermal rather than by nuclear considerations. The reactor core must be operated at a power level that the temperatures of the fuel and cladding anywhere in the core must not exceed safe limits so as to prevent from fuel element damages. Heat transfer from fuel pins can be calculated analytically by using a flat power density in the fuel pin. In actual practice, the neutron flux distribution inside fuel pins results in a smaller effective distance for the heat to be transported to the coolant. This inherent phenomenon gives rise to a heat transfer benefit in fuel pin temperatures. In this research, a quantitative estimate for transferring heat from cylindrical fuel rods is accomplished by considering a non-uniform neutron flux, which leads to a flux depression factor. This, in turn, shifts the temperature inside the fuel pin. A theoretical relationship combining the flux depression factor and a ratio of temperature gradients for uniform and non-uniform is derived, and a computational program, based on energy balance, is developed to validate the considered approximation. (author)

  11. FRAPCON-2: A Computer Code for the Calculation of Steady State Thermal-Mechanical Behavior of Oxide Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Berna, G. A; Bohn, M. P.; Rausch, W. N.; Williford, R. E.; Lanning, D. D.

    1981-01-01

    FRAPCON-2 is a FORTRAN IV computer code that calculates the steady state response of light Mater reactor fuel rods during long-term burnup. The code calculates the temperature, pressure, deformation, and tai lure histories of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include (a) heat conduction through the fuel and cladding, (b) cladding elastic and plastic deformation, (c) fuel-cladding mechanical interaction, (d) fission gas release, (e} fuel rod internal gas pressure, (f) heat transfer between fuel and cladding, (g) cladding oxidation, and (h) heat transfer from cladding to coolant. The code contains necessary material properties, water properties, and heat transfer correlations. FRAPCON-2 is programmed for use on the CDC Cyber 175 and 176 computers. The FRAPCON-2 code Is designed to generate initial conditions for transient fuel rod analysis by either the FRAP-T6 computer code or the thermal-hydraulic code, RELAP4/MOD7 Version 2.

  12. A New Insight into Energy Distribution of Electrons in Fuel-Rod Gap in VVER-1000 Nuclear Reactor

    Science.gov (United States)

    Fereshteh, Golian; Ali, Pazirandeh; Saeed, Mohammadi

    2015-06-01

    In order to calculate the electron energy distribution in the fuel rod gap of a VVER-1000 nuclear reactor, the Fokker-Planck equation (FPE) governing the non-equilibrium behavior of electrons passing through the fuel-rod gap as an absorber has been solved in this paper. Besides, the Monte Carlo Geant4 code was employed to simulate the electron migration in the fuel-rod gap and the energy distribution of electrons was found. As for the results, the accuracy of the FPE was compared to the Geant4 code outcomes and a satisfactory agreement was found. Also, different percentage of the volatile and noble gas fission fragments produced in fission reactions in fuel rod, i.e. Krypton, Xenon, Iodine, Bromine, Rubidium and Cesium were employed so as to investigate their effects on the electrons' energy distribution. The present results show that most of the electrons in the fuel rod's gap were within the thermal energy limitation and the tail of the electron energy distribution was far from a Maxwellian distribution. The interesting outcome was that the electron energy distribution is slightly increased due to the accumulation of fission fragments in the gap. It should be noted that solving the FPE for the energy straggling electrons that are penetrating into the fuel-rod gap in the VVER-1000 nuclear reactor has been carried out for the first time using an analytical approach.

  13. Assessing the Effect of Fuel Burnup on Control Rod Worth for HEU and LEU Cores of Gharr-1

    Directory of Open Access Journals (Sweden)

    E.K. Boafo

    2013-02-01

    Full Text Available An important parameter in the design and analysis of a nuclear reactor is the reactivity worth of the control rod which is a measure of the efficiency of the control rod to absorb excess reactivity. During reactor operation, the control rod worth is affected by factors such as the fuel burnup, Xenon concentration, Samarium concentration and the position of the control rod in the core. This study investigates the effect of fuel burnup on the control rod worth by comparing results of a fresh and an irradiated core of Ghana's Miniature Neutron Source Reactor for both HEU and LEU cores. In this study, two codes have been utilized namely BURNPRO for fuel burnup calculation and MCNP5 which uses densities of actinides of the irradiated fuel obtained from BURNPRO. Results showed a decrease of the control rod worth with burnup for the LEU while rod worth increased with burnup for the HEU core. The average thermal flux in both inner and outer irradiation sites also decreased significantly with burnup for both cores.

  14. Control rod ejection accident analysis for a PWR with thorium fuel loading

    Energy Technology Data Exchange (ETDEWEB)

    Da Cruz, D.F. [Nuclear Research and Consultancy Group NRG, Westerduinweg 3, P.O. Box 25, 1755 ZG Petten (Netherlands)

    2010-07-01

    This paper presents the results of 3-D transient analysis of a pressurized water reactor (PWR) core loaded with 100% Th-Pu MOX fuel assemblies. The aim of this study is to evaluate the safety impact of applying a full loading of this innovative fuel in PWRs of the current generation. A reactivity insertion accident scenario has been simulated using the reactor core analysis code PANTHER, used in conjunction with the lattice code WIMS. A single control rod assembly, with the highest reactivity worth, has been considered to be ejected from the core within 100 milliseconds, which may occur due to failure of the casing of the control rod driver mechanism. Analysis at both hot full power and hot zero power reactor states have been taken into account. The results were compared with those obtained for a representative PWR fuelled with UO{sub 2} fuel assemblies. In general the results obtained for both cores were comparable, with some differences associated mainly to the harder neutron spectrum observed for the Th-Pu MOX core, and to some specific core design features. The study has been performed as part of the LWR-DEPUTY project of the EURATOM 6. Framework Programme, where several aspects of novel fuels are being investigated for deep burning of plutonium in existing nuclear power plants. (authors)

  15. Development of advanced BWR fuel bundle with spectral shift rod - BWR core characteristics with SSR

    Energy Technology Data Exchange (ETDEWEB)

    Hino, T.; Kondo, T.; Chaki, M.; Ohga, Y. [Hitachi-GE Nuclear Energy, Ltd., 1-1, Saiwai-cho, 3-chome, Hitachi-shi, Ibaraki-ken, 317-0073 (Japan); Makigami, T. [Tokyo Electric Power Company Inc., 1-1-3, Uchisaiwai-cho, Chiyoda-ku, Tokyo, 100-0011 (Japan)

    2012-07-01

    The neutron energy spectrum can be varied during an operation cycle to generate and utilize more plutonium from the non-fissile {sup 238}U by changing the void fraction in the core through control of the core coolant flow rate. This operation method, which is called a spectral shift operation, is practiced in BWRs to save natural uranium. A new component called a spectral shift rod (SSR), which is utilized instead of a conventional water rod, has been introduced to amplify the void fraction change and increase the spectral shift effect. In this study, fuel bundle design with the SSR and core design were carried out for the ABWR and the next generation BWR, HP-ABWR (High-Performance ABWR).The core characteristics with the SSR were evaluated and compared with those when using the conventional water rod. Influences of uncertainty of the water level in the SSR on the safety limit minimum critical power ratio (SLMCPR) were considered for evaluation of the uranium saving effect attained by the SSR. As a result, it was found that the amount of natural uranium needed for an operation cycle could be reduced more than 3% with 20% core coolant flow change and more than 5% with 30% core coolant flow change, in the form of increased discharge exposure by using the SSR compared with the conventional water rod use. (authors)

  16. Simulation of accident and normal fuel rod work with Zr-cladding

    Energy Technology Data Exchange (ETDEWEB)

    Tutnov, Anton A.; Tutnov, Alexander A. [Russian Research Centre, Moscow (Russian Federation). Kurchatov Inst.

    1995-12-31

    The technique of simulation of heat-physics, strength and safety characteristics of reactor RBMK and WWER rods under steady-state, transient and accident conditions is presented. That technique is used in mechanic and heat physics codes PULSAR-2 and STALACTITE. Simulation in both full scale and the most stress-loading part of cladding statement under accident conditions are considered. In this zone local swelling and cladding failure are possible. The accident simulation is based on the mechanical creep-plasticity problem solution in three-dimensional approach. The local cladding swelling is initiated with determining of little hot spot on the clad with several degrees temperature departure from average value. Mechanical problem is solved by finite elements method. Interaction of Zr with steam is taken in to account. Fuel and cladding melting, shortness and dispersion formation processes are simulated under subsequent rods warming up. (author). 2 refs., 6 figs.

  17. FY15 Status Report: CIRFT Testing of Spent Nuclear Fuel Rods from Boiler Water Reactor Limerick

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jy-An John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wang, Hong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jiang, Hao [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-06-01

    The objective of this project is to perform a systematic study of used nuclear fuel (UNF, also known as spent nuclear fuel [SNF]) integrity under simulated transportation environments using the Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) hot-cell testing technology developed at Oak Ridge National Laboratory (ORNL) in August 2013. Under Nuclear Regulatory Commission (NRC) sponsorship, ORNL completed four benchmark tests, four static tests, and twelve dynamic or cycle tests on H. B. Robinson (HBR) high burn-up (HBU) fuel. The clad of the HBR fuels was made of Zircaloy-4. Testing was continued in fiscal year (FY) 2014 using Department of Energy (DOE) funds. The additional CIRFT was conducted on three HBR rods (R3, R4, and R5) in which two specimens failed and one specimen was tested to over 2.23 10⁷ cycles without failing. The data analysis on all the HBR UNF rods demonstrated that it is necessary to characterize the fatigue life of the UNF rods in terms of (1) the curvature amplitude and (2) the maximum absolute of curvature extremes. The maximum extremes are significant because they signify the maximum of tensile stress for the outer fiber of the bending rod. CIRFT testing has also addressed a large variation in hydrogen content on the HBR rods. While the load amplitude is the dominant factor that controls the fatigue life of bending rods, the hydrogen content also has an important effect on the lifetime attained at each load range tested. In FY 15, ten SNF rod segments from BWR Limerick were tested using ORNL CIRFT, with one under static and nine dynamic loading conditions. Under static unidirectional loading, a moment of 85 N·m was obtained at maximum curvature 4.0 m⁻¹. The specimen did not show any sign of failure in three repeated loading cycles to almost same maximum curvature. Ten cyclic tests were conducted with amplitude varying from 15.2 to 7.1 N·m. Failure was observed in nine of the tested rod specimens. The cycles to failure were

  18. Measurement of Fresh Fuel Rods to Demonstrate Compliance with Criticality Safety Limits

    Energy Technology Data Exchange (ETDEWEB)

    Miko, David K. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Desimone, David J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-11-03

    In order to operate TA-66 as a radiological facility with the quantity of nuclear material required to fulfil its mission, a criticality safety evaluation was required. This evaluation defined the control parameters for operations at the facility. The resulting evaluation for TA-66 placed limits on the amount of SNM, as well as other materials such as beryllium. In addition, there is a limit on the number of uranium fuel rods allowed subject to enrichment, outer diameter, and overall length restrictions. The enrichments for the rods to be shipped to TA-66 were documented in LA-UR-13-23581, but the outer diameter and length were not documented. This report provides this information.

  19. Results of the first nuclear blowdown test on single fuel rods (LOC-11 Series in PBF)

    Energy Technology Data Exchange (ETDEWEB)

    Larson, J.R.; Evans, D.R.; McCardell, R.K.

    1978-01-01

    This paper presents results of the first nuclear blowdown tests (LOC-11A, LOC-11B, LOC-11C) ever conducted. The Loss-of-Coolant Accident (LOCA) Test Series is being conducted in the Power Burst Facility (PBF) reactor at the Idaho National Engineering Laboratory, near Idaho Falls, Idaho, for the Nuclear Regulatory Commission. The objective of the LOC-11 tests was to obtain data on the behavior of pressurized and unpressurized rods when exposed to a blowdown similar to that expected in a pressurized water reactor (PWR) during a hypothesized double-ended cold-leg break. The data are being used for the development and verification of analytical models that are used to predict coolant and fuel rod pressure during a LOCA in a PWR.

  20. PIE of the second fuel rod from the LOCA experiment (IFA-650.2)

    Energy Technology Data Exchange (ETDEWEB)

    Oberlaender, B.C.; Jenssen, H.K.; Espeland, M.; Solum, N.O.

    2005-07-01

    The LOCA experiment on the second rod (IFA-650.2) a fresh, low-tin Zr-4, pressurised PWR rod was carried out in May 2004. The main objective was to produce ballooning, to determine the time to burst and to assess the material oxidation and hydriding kinetics. The rod pressure at hot conditions and peak PCT were 70 bar and 1050 C, respectively. To document the effect of the LOCA testing on the cladding, rod 2 was subjected in PIE to visual inspection, profilometry and metallography. On visual inspection the clad shows a typical balloon. In the region of max ballooning the clad shows a 35 mm long, < 20 mm burst opening. In the balloon region the outer clad diameter increased by <35% and locally the wall thickness reduction is >55%. The entire rod is covered with a black oxide layer. Below and above the split opening the continuous oxide layer was 40 to 50mum both on water and fuel side of the clad. At the locations of the upper and lower cladding thermocouples the oxide thickness was in the range 24-27 mum. Widmanstaetten structure is seen in the bulk of the clad and confirms the high temperature experienced. A some 40mum wide, hard and brittle zone with oxygen rich globular alpha-grains is found both at the outer and the inner edge of the clad in the balloon region. The zone is widest near the axial split (crack). In the clad few, arbitrary oriented hydride platelets are observed in the balloon area. (Author)

  1. Matpro--version 10: a handbook of materials properties for use in the analysis of light water reactor fuel rod behavior

    Energy Technology Data Exchange (ETDEWEB)

    Reymann, G.A. (comp.)

    1978-02-01

    The materials properties correlations and computer subcodes (MATPRO--Version 10) developed for use with various LWR fuel rod behavior analytical programs at the Idaho National Engineering Laboratory are described. Formulations of fuel rod material properties, which are generally semiempirical in nature, are presented for uranium dioxide and mixed uranium--plutonium dioxide fuel, zircaloy cladding, and fill gas mixtures.

  2. Development of Mechanical Sealing and Laser Welding Technology to Instrument Thermocouple for Nuclear Fuel Test Rod

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Chang-Young; Ahn, Sung-Ho; Hong, Jin-Tae; Kim, Ka-Hye; Huh, Sung-Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Zircaloy-4 of the nuclear fuel test rod, AISI 316L of the mechanical sealing parts, and the MI (mineral insulated) cable at a thermocouple instrumentation are hetero-metals, and are difficult to weld to dissimilar materials. Therefore, a mechanical sealing method to instrument the thermocouple should be conducted using two kinds of sealing process as follows: One is a mechanical sealing process using Swagelok, which is composed of sealing components that consists of an end-cap, a seal tube, a compression ring and a Swagelok nut. The other is a laser welding process used to join a seal tube, and an MI cable, which are made of the same material. The mechanical sealing process should be sealed up with the mechanical contact compressed by the strength forced between a seal tube and an end-cap, and the laser welding process should be conducted to have no defects on the sealing area between a seal tube and an MI cable. Therefore, the mechanical sealing and laser welding techniques need to be developed to accurately measure the centerline temperature of the nuclear fuel test rod in an experimental reactor. The mechanical sealing and laser welding tests were conducted to develop the thermocouple instrumentation techniques for the nuclear fuel test rod. The optimum torque value of a Swagelok nut to seal the mechanical sealing part between the end-cap and seal tube was established through various torque tests using a torque wrench. The optimum laser welding conditions to seal the welding part between a seal tube and an MI cable were obtained through various welding tests using a laser welding system.

  3. Optimum nuclear design of target fuel rod for Mo-99 production in HANARO

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Myung Hyun [Kyung Hee University, Seoul (Korea)

    1998-04-01

    Nuclear target design for Mo-99 production in HANARO was performed, KAERI proposed target design was analyzed and its feasibility was shown. Three commercial target designs of Cintichem, ANL and KAERI were tested for the HANARO irradiation an d they all satisfied with design specification. A parametric study was done for target design options and Mo-99 yields ratio and surface heat flux were compared. Tested parameters were target fuel thickness, irradiation location, target axial length, packing density of powder fuel, size of target radius, target geometry, fuel enrichment, fuel composition, and cladding material. Optimized target fuel was designed for both LEU and HEU options. (author). 17 refs., 33 figs., 42 tabs.

  4. An electrical simulator of a nuclear fuel rod cooled by nucleate boiling

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Antonio Carlos Lopes da [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)], e-mail: aclc@cdtn.br; Machado, Luiz; Koury, Ricardo Nicolau Nassar [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Engenharia Mecanica], e-mail: luizm@demec.ufmg.br; Bonjour, Jocelyn [CETHIL, UMR5008, CNRS, INSA-Lyon (France)], e-mail: jocelyn.bonjour@insa-lyon.fr; Passos, Julio Cesar [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica. LEPTEN/Boiling], e-mail: jpassos@emc.ufsc.br

    2009-07-01

    This study investigates an electrical heated test section designed to simulate a nuclear fuel rod. This simulator comprises a stainless steel vertical tube, with length and outside diameter of 600 mm and 10 mm, respectively, inside which there is a high power electrical resistor. The heat generated is removed by means of enhanced confined subcooled nucleate boiling of water in an annular space containing 153 small metal inclined discs. The tests were performed under electrical power and pressure up to 48 kW and 40 bar, respectively. The results show that the experimental boiling heat transfer coefficients are in good agreement with those calculated using the Jens-Lottes correlation. (author)

  5. Simulation with DIONISIO 1.0 of thermal and mechanical pellet-cladding interaction in nuclear fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Soba, Alejandro [Departamento Combustibles Nucleares, Comision Nacional de Energia Atomica, Avenida del Libertador 8250, 1429 Buenos Aires (Argentina); Denis, Alicia [Departamento Combustibles Nucleares, Comision Nacional de Energia Atomica, Avenida del Libertador 8250, 1429 Buenos Aires (Argentina)], E-mail: denis@cnea.gov.ar

    2008-02-29

    The code DIONISIO 1.0 describes most of the main phenomena occurring in a fuel rod throughout its life under normal operation conditions of a nuclear thermal reactor. Starting from the power history, DIONISIO predicts the temperature distribution in the domain, elastic and plastic stress and strain, creep, swelling and densification, release of fission gases, caesium and iodine to the rod free volume, gas mixing, pressure increase, restructuring and grain growth in the UO{sub 2} pellet, irradiation growth of the Zircaloy cladding, oxide layer growth on its surface, hydrogen uptake and the effects of a corrosive atmosphere either internal or external. In particular, the models of thermal conductance of the gap and of pellet-cladding mechanical interaction incorporated to the code constitute two realistic tools. The possibility of gap closure (including partial contact between rough surfaces) and reopening during burnup is allowed. The non-linear differential equations are integrated by the finite element method in two-dimensions assuming cylindrical symmetry. Good results are obtained for the simulation of several irradiation tests.

  6. Simulation with DIONISIO 1.0 of thermal and mechanical pellet-cladding interaction in nuclear fuel rods

    Science.gov (United States)

    Soba, Alejandro; Denis, Alicia

    2008-02-01

    The code DIONISIO 1.0 describes most of the main phenomena occurring in a fuel rod throughout its life under normal operation conditions of a nuclear thermal reactor. Starting from the power history, DIONISIO predicts the temperature distribution in the domain, elastic and plastic stress and strain, creep, swelling and densification, release of fission gases, caesium and iodine to the rod free volume, gas mixing, pressure increase, restructuring and grain growth in the UO 2 pellet, irradiation growth of the Zircaloy cladding, oxide layer growth on its surface, hydrogen uptake and the effects of a corrosive atmosphere either internal or external. In particular, the models of thermal conductance of the gap and of pellet-cladding mechanical interaction incorporated to the code constitute two realistic tools. The possibility of gap closure (including partial contact between rough surfaces) and reopening during burnup is allowed. The non-linear differential equations are integrated by the finite element method in two-dimensions assuming cylindrical symmetry. Good results are obtained for the simulation of several irradiation tests.

  7. In-pile tests at Karlsruhe of LWR fuel-rod behavior during the heatup phase of a LOCA

    Energy Technology Data Exchange (ETDEWEB)

    Karb, E.H.

    1980-01-01

    In order to investigate the influence of a nuclar environment on the mechanisms of fuel-rod failure, in-pile tests simulating the heatup phase of a loss-of-coolant accident in a pressurized-water reactor are being conducted with irradiated and unirradiated short-length single rods in the FR2 reactor at Kernforschungszentrum karlsruhe (Karlsruhe Nuclear Reasearch Center), Federal Republic of Germany, within the Project Nuclear Safety. With nearly 70% of the scheduled tests completed, no such influences have been found. The in-pile burst and deformation data are in good agreement with results from nonnuclear tests with electrically heated fuel-rod simulators. The phenomenon of pellet disintegration, which has been observed in all tests with previously irradiated rods, needs further investigation.

  8. Synthesis and Analysis of Alpha Silicon Carbide Components for Encapsulation of Fuel Rods and Pellets

    Energy Technology Data Exchange (ETDEWEB)

    Kevin M. McHugh; John E. Garnier; George W. Griffith

    2011-09-01

    The chemical, mechanical and thermal properties of silicon carbide (SiC) along with its low neutron activation and stability in a radiation field make it an attractive material for encapsulating fuel rods and fuel pellets. The alpha phase (6H) is particularly stable. Unfortunately, it requires very high temperature processing and is not readily available in fibers or near-net shapes. This paper describes an investigation to fabricate a-SiC as thin films, fibers and near-net-shape products by direct conversion of carbon using silicon monoxide vapor at temperatures less than 1700 C. In addition, experiments to nucleate the alpha phase during pyrolysis of polysilazane, are also described. Structure and composition were characterized using scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. Preliminary tensile property analysis of fibers was also performed.

  9. US Forest Service LANDFIRE Surface Fuel

    Data.gov (United States)

    US Forest Service, Department of Agriculture — LANDFIRE surface fuel data describe the composition and characteristics of wildland surface fuel and can be implemented within models to predict wildland fire...

  10. Determination of the rod-wise fission gas release fraction in a complete fuel assembly using non-destructive gamma emission tomography

    Science.gov (United States)

    Holcombe, Scott; Andersson, Peter; Svärd, Staffan Jacobsson; Hallstadius, Lars

    2016-11-01

    A gamma tomography instrument has been developed at the Halden Boiling Water Reactor (HBWR) in cooperation between the Institute for Energy Technology, Westinghouse (Sweden) and Uppsala University. The instrument is used to record the gamma radiation field surrounding complete fuel assemblies and consists of a shielded enclosure with fixtures to accurately position the fuel and detector relative to each other. A High Purity Germanium detector is used for acquiring high-resolution spectroscopic data, allowing for analysis of multiple gamma-ray peaks. Using the data extracted from the selected peaks, tomographic reconstruction algorithms are used to reproduce the corresponding spatial gamma-ray source distributions within the fuel assembly. With this method, rod-wise data can be can be deduced without the need to dismantle the fuel. In this work, the tomographic device has been experimentally benchmarked for non-destructive rod-wise determination of the Fission Gas Release (FGR) fraction. Measurements were performed on the fuel-stack and gas-plenum regions of a complete fuel assembly, and quantitative tomographic reconstructions of the measurement data were performed in order to determine the rod-wise ratio of 85Kr in the gas plenum to 137Cs in the fuel stack. The rod-wise ratio of 85Kr/137Cs was, in turn, used to calculate the rod-wise FGR fraction. In connection to the tomographic measurements, the fuel rods were also measured individually using gamma scanning in order to provide an experimental benchmark for the tomographic method. Fuel rods from two donor driver fuel assemblies were placed into a nine-rod HBWR driver fuel assembly configuration. In order to provide a challenging measurement object and thus an appropriate benchmark for the tomographic method, five rods were taken from an assembly with a burnup of 51 MWd/kgUO2, and four rods were from an assembly with a burnup of 26 MWd/kgUO2. At the time of the measurements, the nine rods had cooled for

  11. Zirconium-based alloys, nuclear fuel rods and nuclear reactors including such alloys, and related methods

    Science.gov (United States)

    Mariani, Robert Dominick

    2014-09-09

    Zirconium-based metal alloy compositions comprise zirconium, a first additive in which the permeability of hydrogen decreases with increasing temperatures at least over a temperature range extending from 350.degree. C. to 750.degree. C., and a second additive having a solubility in zirconium over the temperature range extending from 350.degree. C. to 750.degree. C. At least one of a solubility of the first additive in the second additive over the temperature range extending from 350.degree. C. to 750.degree. C. and a solubility of the second additive in the first additive over the temperature range extending from 350.degree. C. to 750.degree. C. is higher than the solubility of the second additive in zirconium over the temperature range extending from 350.degree. C. to 750.degree. C. Nuclear fuel rods include a cladding material comprising such metal alloy compositions, and nuclear reactors include such fuel rods. Methods are used to fabricate such zirconium-based metal alloy compositions.

  12. Process Management Development for Quality Monitoring on Resistance Weldment of Nuclear Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Na, Tae Hyung; Yang, Kyung Hwan; Kim, In Kyu [KEPCO, Daejeon (Korea, Republic of)

    2016-05-15

    The current, welding force, and displacement are displayed on the indicator during welding. However, real-time quality control is not performed. Due to the importance of fuel rod weldment, many studies on welding procedures have been conducted. However, there are not enough studies regarding weldment quality evaluation. On the other hand, there are continuous studies on the monitoring and control of welding phenomena. In resistance welding, which is performed in a very short time, it is important to find the process parameters that well represent the weld zone formation and the welding process. In his study, Gould attempted to analyze melt zone formation using the finite difference method. Using the artificial neural network, Javed and Sanders, Messler Jr et al., Cho and Rhee, Li and Gong et al. estimated the size of the melt zone by mapping a nonlinear functional relation between the weldment and the electrode head movement, which is a typical welding process parameter. Applications of the artificial intelligence method include fuzzy control using electrode displacement, fuzzy control using the optimal power curve, neural network control using the dynamic resistance curve, fuzzy adaptive control using the optimal electrode curve, etc. Therefore, this study induced quality factors for the real-time quality control of nuclear fuel rod end plug weldment using instantaneous dynamic resistance (IDR), which incorporates the instantaneous value of secondary current and voltage of the transformer, and using instantaneous dynamic force (IDF), obtained real-time during welding.

  13. Experimental and numerical study on lead-bismuth heat transfer in a fuel rod simulator

    Science.gov (United States)

    Ma, Weimin; Karbojian, Aram; Hollands, Thorsten; Koch, Marco K.

    2011-08-01

    As a task of the EU project IP EUROTRANS towards development of an Accelerator Driven System (ADS) dedicated to the transmutation of long-lived fission products, experiments and simulations were performed on the TALL test facility at KTH to investigate thermal hydraulics along a single fuel rod simulator cooled by lead-bismuth eutectic (LBE). The fuel rod simulator is concentrically inserted in a tube, so that an annular channel is formed for LBE flow. This paper presents the measured temperature profiles in the annular channel, and the comparisons with the simulation results of the CFX code. The primary objective is to help understanding the LBE heat transfer characteristics and qualifying the turbulence and heat transfer modeling for LBE application. The quantitative comparison between the calculated and measured temperatures of the LBE indicates that the simulation underestimates the experiment at most radial and axial positions. Finally the uncertainties in measurement and the deficiency in turbulence models resulting in such a disagreement were discussed, which will be directive and beneficial to future work in the field.

  14. Thermo-Mechanical Analysis of Coated Particle Fuel Experiencing a Fast Control Rod Ejection Transient

    Energy Technology Data Exchange (ETDEWEB)

    Ortensi, J.; Brian Boer; Abderrafi M. Ougouag

    2010-10-01

    A rapid increase of the temperature and the mechanical stress is expected in TRISO coated particle fuel that experiences a fast Total Control Rod Ejection (CRE) transient event. During this event the reactor power in the pebble bed core increases significantly for a short time interval. The power is deposited instantly and locally in the fuel kernel. This could result in a rapid increase of the pressure in the buffer layer of the coated fuel particle and, consequently, in an increase of the coating stresses. These stresses determine the mechanical failure probability of the coatings, which serve as the containment of radioactive fission products in the Pebble Bed Reactor (PBR). A new calculation procedure has been implemented at the Idaho National Laboratory (INL), which analyzes the transient fuel performance behavior of TRISO fuel particles in PBRs. This early capability can easily be extended to prismatic designs, given the availability of neutronic and thermal-fluid solvers. The full-core coupled neutronic and thermal-fluid analysis has been modeled with CYNOD-THERMIX. The temperature fields for the fuel kernel and the particle coatings, as well as the gas pressures in the buffer layer, are calculated with the THETRIS module explicitly during the transient calculation. Results from this module are part of the feedback loop within the neutronic-thermal fluid iterations performed for each time step. The temperature and internal pressure values for each pebble type in each region of the core are then input to the PArticle STress Analysis (PASTA) code, which determines the particle coating stresses and the fraction of failed particles. This paper presents an investigation of a Total Control Rod Ejection (TCRE) incident in the 400 MWth Pebble Bed Modular reactor design using the above described calculation procedure. The transient corresponds to a reactivity insertion of $3 (~2000 pcm) reaching 35 times the nominal power in 0.5 seconds. For each position in the core

  15. NSRR experiment with un-irradiated uranium-zirconium hydride fuel. Design, fabrication process and inspection data of test fuel rod

    Energy Technology Data Exchange (ETDEWEB)

    Sasajima, Hideo; Fuketa, Toyoshi; Ishijima, Kiyomi; Kuroha, Hiroshi; Ikeda, Yoshikazu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Aizawa, Keiichi

    1998-08-01

    An experiment plan is progressing in the Nuclear Safety Research Reactor (NSRR) to perform pulse-irradiation with uranium-zirconium hydride (U-ZrH{sub x}) fuel. This fuel is widely used in the training research and isotope production reactor of GA (TRIGA). The objectives of the experiment are to determine the fuel rod failure threshold and to investigate fuel behavior under simulated reactivity initiated accident (RIA) conditions. This report summarizes design, fabrication process and inspection data of the test fuel rods before pulse-irradiation. The experiment with U-ZrH{sub x} fuel will realize precise safety evaluation, and improve the TRIGA reactor performance. The data to be obtained in this program will also contribute development of next-generation TRIGA reactor and its safety evaluation. (author)

  16. Computerized operating procedures for shearing and dissolution of segments from LWBR (Light Water Breeder Reactor) fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Osudar, J.; Deeken, P.G.; Graczyk, D.G.; Fagan, J.E.; Martino, F.J.; Parks, J.E.; Levitz, N.M.; Kessie, R.W.; Leddin, J.M.

    1987-05-01

    This report presents two detailed computerized operating procedures developed to assist and control the shearing and dissolution of irradiated fuel rods. The procedures were employed in the destructive analysis of end-of-life fuel rods from the Light Water Breeder Reactor (LWBR) that was designed by the Westinghouse Electric Corporation Bettis Atomic Power Laboratory. Seventeen entire fuel rods from the end-of-life core of the LWBR were sheared into 169 precisely characterized segments, and more than 150 of these segments were dissolved during execution of the LWBR Proof-of-Breeding (LWBR-POB) Analytical Support Project at Argonne National Laboratory. The procedures illustrate our approaches to process monitoring, data reduction, and quality assurance during the LWBR-POB work.

  17. Design of the Testing Set-up for a Nuclear Fuel Rod by Neutron Radiography at CARR

    Science.gov (United States)

    Wei, Guohai; Han, Songbai; Wang, Hongli; Hao, Lijie; Wu, Meimei; He, Linfeng; Wang, Yu; Liu, Yuntao; Sun, Kai; Chen, Dongfeng

    In this paper, an experimental set-up dedicated to non-destructively test a 15cm-long Pressurized Water Reactor (PWR) nuclear fuel rod by neutron radiography (NR) is described. It consists of three parts: transport container, imaging block and steel support. The design of the transport container was optimized with Monte-Carlo Simulation by the MCNP code. The material for the shell of the transport container was chosen to be lead with the thickness of 13 cm. Also, the mechanical devices were designed to control fuel rod movement inside the container. The imaging block was designed as the exposure platform, with three openings for the neutron beam, neutron converter foil, and specimen. Development and application of this experimental set-up will help gain much experience for investigating the actual irradiated fuel rod by neutron radiography at CARR in the future.

  18. Model of fracture for the Zry cladding of nuclear fuel rods included in the code DIONISIO 1.0

    Energy Technology Data Exchange (ETDEWEB)

    Soba, Alejandro [Departamento Combustibles Nucleares, Comision Nacional de Energia Atomica, Av. del Libertador 8250, 1429 Buenos Aires (Argentina)], E-mail: soba@cnea.gov.ar; Denis, Alicia [Departamento Combustibles Nucleares, Comision Nacional de Energia Atomica, Av. del Libertador 8250, 1429 Buenos Aires (Argentina)], E-mail: denis@cnea.gov.ar

    2008-12-15

    The DIONISIO code describes most of the main phenomena occurring in a fuel rod during normal operation of a nuclear power reactor. Starting from the irradiation history, the code predicts the temperature distribution, elastic and plastic stress and strain, creep, swelling and densification, release of fission gases, caesium and iodine to the internal rod volume, gas mixing, pressure increase, irradiation growth of the cladding, development of an oxide layer on its surface and hydrogen uptake, restructuring and grain growth in the pellet. This work presents the model of Zircaloy fracture included in the code DIONISIO 1.0. The model of pellet-cladding mechanical interaction (PCMI) provides the forces caused by the solid-solid contact which add to the changing internal pressure and to the constant external pressure. Besides, the program evaluates the effects of a corrosive atmosphere (stress corrosion cracking, SCC) internal or external. With these data, the code calculates the J integral around the tip of an initiated crack, and proceeds to analyze, according to the quantity of corrosive substance dissolved and the cladding stress field, if the crack remains unchanged, if it grows due to the I-SCC mechanism, or if propagation is ductile, following the R curve of the material. Results corresponding to different PHWR and PWR reactors are presented and compared with code results. In particular, good agreement is obtained in the simulation of MOX experiments, where the cladding failed due to propagation of cracks originated in SCC.

  19. Shaping of steel mold surface of lens array by electrical discharge machining with single rod electrode.

    Science.gov (United States)

    Takino, Hideo; Hosaka, Takahiro

    2014-11-20

    We propose a method for fabricating a lens array mold by electrical discharge machining (EDM). In this method, the tips of rods are machined individually to form a specific surface, and then a number of the machined rods are arranged to construct an electrode for EDM. The repetition of the EDM process using the electrode enables a number of lens elements to be produced on the mold surface. The effectiveness of our proposed method is demonstrated by shaping a lens array mold made of stainless steel with 16 spherical elements, in which the EDM process with a single rod electrode is repeatedly conducted.

  20. Elastic analysis of thermal gradient bowing in rod-type fuel elements subjected to axial thrust (LWBR Development Program)

    Energy Technology Data Exchange (ETDEWEB)

    Newman, J.B.

    1968-01-01

    Thermal radient bowing of rod type fuel elements can be analyzed in terms of the deflections of a precurved beam. The fundamental aspects of an analysis of axially compressed multispan beams are given. Elasticity of supports in both axial and transverse directions is considered; the technique is applicable to problems in which the axial thrust depends on the transverse deflection as well as problems with prescribed axial thrust. The formulas presented constitute the theory for a computer program of broad applicability, not only in the analysis of fuel rod bowing, but also to almost any multispan beam, particularly when the effects of axial loads cannot be neglected. 17 references. (NSA 22: 22866)

  1. Numerical Prediction of Dual-Cooled Annular Fuel Temperature During Control Rod Ejection Accident in OPR1000

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chan Eun; In, Wang Kee; Yang, Soo Hyung; Chun, Tae Hyun; Song, Kun Woo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2009-10-15

    A dual-cooled annular fuel concept for a light water reactor has been introduced by MIT for a significant amount of reactor power uprate. MIT proposed a 13x13 annular fuel array replacing the 17x17 solid fuel in the Westinghouse 4-loop plant, which could increase the core power up to 50% with the considerable changes in the major reactor components. The Korea Atomic Energy Research Institute (KAERI) is also conducting a research to develop a dual-cooled fuel for its employment in an optimized pressurized water reactor in Korea, OPR1000. The dual-cooled fuel for the OPR1000 is targeted to increase the reactor power by 20% as well as reduce the fuel-pellet temperature by more than 30% without a change to the reactor components other than the fuel. Numerous technical tasks exist for assessing the applicability of the dual cooled annular fuel to the power uprate in the OPR1000. One of the important tasks is to evaluate the performance of the annular fuel during the design basis events. Particularly, the fuel temperature and the peak cladding temperature (PCT) are the important variables during the control rod ejection accident (REA), since the rod averaged fuel enthalpy should be lower than its safety limit. The fuel enthalpy is known to largely depend on the fuel temperature. This paper presents the predictions of the fuel and peak cladding temperatures during the REA. A general-purpose structural code, ABAQUS-6.8 and a computational fluid dynamics code, ANSYS CFX-11.0 were used to perform the numerical analysis of a heat transfer in the annular fuel as well as the solid fuel. The numerical predictions of the fuel maximum temperature (FMT) and PCT are compared against those predicted by a best-estimate system transient analysis code, MARS.

  2. Entrainment and deposition modeling of liquid films with applications for BWR fuel rod dryout

    Science.gov (United States)

    Ratnayake, Ruwan Kumara

    While best estimate computer codes provide the licensing basis for nuclear power facilities, they also serve as analytical tools in overall plant and component design procedures. An ideal best estimate code would comprise of universally applicable mechanistic models for all its components. However, due to the limited understanding in these specific areas, many of the models and correlations used in these codes reflect high levels of empiricism. As a result, the use of such models is strictly limited to the range of parameters within which the experiments have been conducted. Disagreements between best estimate code predictions and experimental results are often explained by the mechanistic inadequacies of embedded models. Significant mismatches between calculated and experimental critical power values are common observations in the analyses of Boiling Water Reactors (BWR). Based on experimental observations and calculations, these mismatches are attributed to the additional entrainment and deposition caused by spacer grids in BWR fuel assemblies. In COBRA-TF (Coolant Boiling in Rod Arrays-Two Fluid); a state of the art industrial best estimate code, these disagreements are hypothesized to occur due the absence of an appropriate spacer grid model. In this thesis, development of a suitably detailed spacer grid model and integrating it to COBRA-TF is documented. The new spacer grid model is highly mechanistic so that the applicability of it is not seriously affected by geometric variations in different spacer grid designs. COBRA-TF (original version) simulations performed on single tube tests and BWR rod bundles with spacer grids showed that single tube predictions were more accurate than those of the rod bundles. This observation is understood to arise from the non-availability of a suitable spacer grid model in COBRA-TF. Air water entrainment experiments were conducted in a test section simulating two adjacent BWR sub channels to visualize the flow behavior at

  3. Excellent bonding behaviour of novel surface-tailored fibre composite rods with cementitious matrix

    Indian Academy of Sciences (India)

    Fernando Cunha; Sohel Rana; Raul Fangueiro; Graça Vasconcelos

    2014-08-01

    Novel composite rods were produced by a special braiding technique that involves braiding of polyester yarns around a core of resin-impregnated carbon fibres and subsequent curing. The surface roughness of these braided rods was tailored by replacing one or two simple yarns in the outer-braided layer with braided yarns (produced from 8 simple yarns) and adjusting the take-up velocity. Pull-out tests were carried out to characterize the bond behaviour of these composite rods with cementitious matrix. It was observed that the rod produced with two braided yarns in the outer cover and highest take-up speed was ruptured completely before pull-out, leading to full utilization of its tensile strength, and exhibited 134% higher pull-out force as compared to the rods produced using only simple braiding yarns.

  4. Two-dimensional thermal analysis of a fuel rod by finite volume method

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Rhayanne Y.N.; Silva, Mario A.B. da; Lira, Carlos A.B. de O., E-mail: ryncosta@gmail.com, E-mail: mabs500@gmail.com, E-mail: cabol@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Departamaento de Energia Nuclear

    2015-07-01

    In a nuclear reactor, the amount of power generation is limited by thermal and physic limitations rather than by nuclear parameters. The operation of a reactor core, considering the best heat removal system, must take into account the fact that the temperatures of fuel and cladding shall not exceed safety limits anywhere in the core. If such considerations are not considered, damages in the fuel element may release huge quantities of radioactive materials in the coolant or even core meltdown. Thermal analyses for fuel rods are often accomplished by considering one-dimensional heat diffusion equation. The aim of this study is to develop the first paper to verify the temperature distribution for a two-dimensional heat transfer problem in an advanced reactor. The methodology is based on the Finite Volume Method (FVM), which considers a balance for the property of interest. The validation for such methodology is made by comparing numerical and analytical solutions. For the two-dimensional analysis, the results indicate that the temperature profile agree with expected physical considerations, providing quantitative information for the development of advanced reactors. (author)

  5. Fuel performance improvement program: description and characterization of HBWR Series H-2, H-3, and H-4 test rods

    Energy Technology Data Exchange (ETDEWEB)

    Guenther, R.J.; Barner, J.O.; Welty, R.K.

    1980-03-01

    The fabrication process and as-built characteristics of the HBWR Series H-2 and H-3 test rods, as well as the three packed-particle (sphere-pac) rods in HBWR Series H-4 are described. The HBWR Series H-2, H-3, and H-4 tests are part of the irradiation test program of the Fuel Performance Improvement Program. Fifteen rods were fabricated for the three test series. Rod designs include: (1) a reference dished pellet design incorporating chamfered edges, (2) a chamfered, annular pellet design combined with graphite-coated cladding, and (3) a sphere-pac design. Both the annular-coated and sphere-pac designs include internal pressurization using helium.

  6. Eddy current NDT: a suitable tool to measure oxide layer thickness in PWR fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Alencar, Donizete A.; Silva Junior, Silverio F. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), Belo Horizonte, MG (Brazil)], e-mail: daa@cdtn.br, e-mail: silvasf@cdtn.br; Vieira, Andre L.P.S. [Industrias Nucleares do Brasil (INB S.A.), Resende, RJ (Brazil). Fabrica de Combustivel Nuclear], e-mail: andre@inb.gov.br; Soares, Adolpho [Technotest Consultoria e Acessoria Ltda., Belo Horizonte, MG (Brazil)], e-mail: adolpho@technotest.com.br

    2009-07-01

    Eddy current is a nondestructive test (NDT) widely used in industry to support integrity analysis of components and equipment. In the nuclear area it is frequently applied to inspect tubes installed in tube exchangers, such as steam generators and condensers in PWR plants, as well as turbine blades. Adequately assisted by means of robotic devices, that inspection method has been pointed as a suitable tool to perform accurate oxide layer thickness measurements in PWR fuel rods. This paper shows some theoretical aspects and physical operating principles of the inspection method, as well as test probes construction details, and the calibration reference standards fabrication processes. Furthermore, some data, experimentally obtained at INB laboratories and other technical information obtained from TECNATOM S.A. are presented, showing the accuracy and efficacy of such NDT method. (author)

  7. Structure Optimization Design of the Electronically Controlled Fuel Control Rod System in a Diesel Engine

    Directory of Open Access Journals (Sweden)

    Hui Jin

    2015-01-01

    Full Text Available Poor ride comfort and shorter clutch life span are the key factors restricting the commercialization of automated manual transmission (AMT. For nonelectrically controlled engines or AMT where cooperative control between the engine and the transmission is not realizable, applying electronically controlled fuel control rod systems (ECFCRS is an effective way to solve these problems. By applying design software such as CATIA, Matlab and Simulink, and MSC Adams, a suite of optimization design methods for ECFCRS drive mechanisms are developed here. Based on these new methods, design requirements can be analyzed comprehensively and the design scheme can be modified easily, thus greatly shortening the design cycle. The bench tests and real vehicle tests indicate that the system developed achieves preferable engine speed following-up performance and engine speed regulating performance. The method developed has significance as a reference for developing other vehicle systems.

  8. LWR fuel rod behavior during reactor tests under loss-of-coolant conditions: Results of the FR2 in-pile tests

    Energy Technology Data Exchange (ETDEWEB)

    Karb, E.H.; Sepold, L.; Hofmann, P.; Petersen, C.; Schanz, G.; Zimmermann, H. (Kernforschungszentrum Karlsruhe G.m.b.H. (Germany, F.R.))

    1982-05-01

    Results of the FR2 in-pile tests on fuel rod behavior under loss-of-coolant accident (LOCA) conditions are presented. To investigate the possible influence of a nuclear environment on fuel rod failure mechanisms, unirradiated as well as irradiated (2500 to 35,000 MWd/tsub(U)) PWR-type test fuel rods were exposed to temperature transients simulating the second heatup phase of a LOCA. Loaded by internal overpressure, the cladding ballooned and ruptured. The burst data do not indicate major differences from results obtained out-of-pile with electrically heated fuel rod simulators, and do not show an influence of burnup. The fuel pellets in previously irradiated rods, already cracked during normal operation, crumbled completely in the regions with large cladding deformation. Post-test examinations revealed cladding mechanical behavior and oxidation to be comparable to out-of-pile results, with relatively little fission gas release during the transient.

  9. Comparative Analysis of Structural Changes In U-Mo Dispersed Fuel of Full-Size Fuel Elements And Mini-Rods Irradiated In The MIR Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Izhutov, Aleksey L.; Iakovlev, Valeriy V.; Novoselov, Andrey E. and others

    2013-12-15

    The paper summarizes the irradiation test and post-irradiation examination (PIE) data for the U-Mo low-enriched fuel that was irradiated in the MIR reactor under the RERTR Program. The PIE data were analyzed for both full-size fuel rods and mini-rods with atomized powder dispersed in Al matrix as well as with additions of 2%, 5% and 13% of silicon in the matrix and ZrN protective coating on the fuel particles. The full-size fuel rods were irradiated up to an average burnup of ∼ 60%{sup 235}U; the mini-rods were irradiated to an average burnup of ∼ 85%{sup 235}U. The presented data show a significant increase of the void fraction in the U-Mo alloy as the U-235 burnup rises from ∼ 40% up to ∼ 85%. The effect of irradiation test conditions and U-235 burnup were analyzed with regard to the formation of an interaction layer between the matrix and fuel particles as well as generation of porosity in the U-Mo alloy. Shown here are changes in distribution of U fission products as the U-235 burnup increases from ∼ 40% up to ∼ 85%.

  10. Tomography on nuclear fuel rods in the nuclear power plant of Dodewaard. Tomografie aan splijtstofstaven in de centrale Dodewaard

    Energy Technology Data Exchange (ETDEWEB)

    Tanke, R.H.J.; Jaspers, J.E.; Gaalman, P.A.M. (KEMA, Arnhem (Netherlands). Division Research and Development)

    1990-09-06

    This report discusses the feasibility of using emission tomography on fuel rods in the Dodewaard reactor. The tomography can be used to increase the efficiency of the use of fissionable material. (R.A.B.). 4 refs.; 17 figs.; 1 tab.

  11. Thermal analysis of lithium cooled natural circulation loop module for fuel rod testing in the Fast Flux Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Eyler, L.L.; Kim, D.; Stover, R.L.; Beaver, T.R.

    1987-01-01

    Maximum heat removal capability of a lithium cooled natural circulation fuel rod test module design is determined. Loop geometry is optimized within limitations of design specifications for nominal operation temperatures, materials, and test module environment. Results provide test module operation limits and range of potential uncertainties. 3 refs., 12 figs.

  12. A Procedure to Address the Fuel Rod Failures during LB-LOCA Transient in Atucha-2 NPP

    Directory of Open Access Journals (Sweden)

    Martina Adorni

    2011-01-01

    Full Text Available Depending on the specific event scenario and on the purpose of the analysis, the availability of calculation methods that are not implemented in the standard system thermal hydraulic codes might be required. This may imply the use of a dedicated fuel rod thermomechanical computer code. This paper provides an outline of the methodology for the analysis of the 2A LB-LOCA accident in Atucha-2 NPP and describes the procedure adopted for the use of the fuel rod thermomechanical code. The methodology implies the application of best estimate thermalhydraulics, neutron physics, and fuel pin performance computer codes, with the objective to verify the compliance with the specific acceptance criteria. The fuel pin performance code is applied with the main objective to evaluate the extent of cladding failures during the transient. The procedure consists of a deterministic calculation by the fuel performance code of each individual fuel rod during its lifetime and in the subsequent LB-LOCA transient calculations. The boundary and initial conditions are provided by core physics and three-dimensional neutron kinetic coupled thermal-hydraulic system codes calculations. The procedure is completed by the sensitivity calculations and the application of the probabilistic method, which are outside the scope of the current paper.

  13. Starting Point, Keys and Milestones of a Computer Code for the Simulation of the Behaviour of a Nuclear Fuel Rod

    Directory of Open Access Journals (Sweden)

    Armando C. Marino

    2011-01-01

    Full Text Available The BaCo code (“Barra Combustible” was developed at the Atomic Energy National Commission of Argentina (CNEA for the simulation of nuclear fuel rod behaviour under irradiation conditions. We present in this paper a brief description of the code and the strategy used for the development, improvement, enhancement, and validation of a BaCo during the last 30 years. “Extreme case analysis”, parametric (or sensitivity, probabilistic (or statistic analysis plus the analysis of the fuel performance (full core analysis are the tools developed in the structure of BaCo in order to improve the understanding of the burnup extension in the Atucha I NPP, and the design of advanced fuel elements as CARA and CAREM. The 3D additional tools of BaCo can enhance the understanding of the fuel rod behaviour, the fuel design, and the safety margins. The modular structure of the BaCo code and its detailed coupling of thermo-mechanical and irradiation-induced phenomena make it a powerful tool for the prediction of the influence of material properties on the fuel rod performance and integrity.

  14. Development of FUELSIM/MOD0 for the detailed analysis of LWR fuel rod behavior under normal operation conditions with extended burnup fuel

    Energy Technology Data Exchange (ETDEWEB)

    Berna, G.A.; Allison, C.M. [Innovative Systems Software LLC, 1284 South Woodruff, Idaho Falls, ID (United States)

    1999-07-01

    The FUELSIM code is being developed by Innovative Systems Software as part of the international SCDAP Development and Training Program. FUELSIM is being developed as a 'stand-alone' best-estimate fuel behavior code with evaluation modeling options. The long term goal of the code is to predict fuel performance over the full range of conditions from normal operating behavior to severe accident conditions using a combination of models from the FRAPCON-3, FRAP-T6, SCDAP, and MATPRO fuel behavior codes. FUELSIM/MOD0 is the first release of the code and includes models to predict the behavior of LWR fuel rods during normal operating conditions including the influence of extended burnup fuel. The code calculates the temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The code models all the important phenomena that occur during normal operating conditions and contains necessary materials properties, water properties, and heat transfer correlations. The code runs on a variety of computers and operating systems including UNIX, LINUX, and Windows NT or 95. (author)

  15. Effects of gap size and excitation frequency on the vibrational behavior and wear rate of fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Zupan [Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Thouless, M.D., E-mail: thouless@umich.edu [Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Department of Materials Science & Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Lu, Wei, E-mail: weilu@umich.edu [Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109 (United States)

    2016-11-15

    Graphical abstract: A wear map shows wear rate as a function of the grid-to-rod gap size and the frequency of the excitation force. The critical gap size, which is associated with the maximum wear rate, lies within the harmonic regime. In the no wear region the amplitude of the rod vibration is smaller than the gap size so that no impact between the rod and plate can happen. The curve of the resonant frequency of the system appears to overlap with the peaks in the contour. - Highlights: • A 3D finite-element based approach to study grid-to-rod fretting. • Two important factors: grid-to-rod gap size and frequency of the excitation force. • Rod vibration shows three regimes: harmonic, period-doubling and chaotic. • A critical gap size is associated with the maximum wear rate. • A wear map shows wear rate as a function of the gap size and excitation frequency. - Abstract: Grid-to-rod fretting (GTRF) wear is a major cause of fuel leaks. Understanding its mechanism is crucial for improving the reliability of nuclear reactors. In this paper we present a three-dimensional, finite-element based approach, which reveals how the wear rate depends on the size of the gap between the grid and the fuel rod, and on the frequency of the excitation force. We show that these two factors affect the dynamic vibration of the rod, which leads to three different regimes: harmonic, period-doubling and chaotic. The wear rate in the harmonic regime is significantly larger than that in the other two regimes, and reaches a maximum when the excitation frequency is close to the resonant frequency of the system, which is dependent on the gap size. We introduce the concept of a critical gap size that gives the maximum wear rate, and we identify the properties and values of this critical gap size. A wear map is developed as a result of a large number of parametric studies. This map shows quantitatively the wear rate as a function of the gap size and excitation frequency, and will be a

  16. Technical Development of Gamma Scanning for Irradiated Fuel Rod after Upgrade of System in Hot-cell

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Woo Seog; Kim, Hee Moon; Baik, Seung Je; Yoo, Byung Ok; Choo, Yong Sun

    2007-06-15

    Non-destructive test system was installed at hot-cell(M1) in IMEF(Irradiated Materials Examination Facility) more than 10 years ago for the diametric measurement and gamma scanning of fuel rod. But this system must be needed to be remodeled for the effective operations. In 2006, the system was upgraded for 3 months. The collimator bench can be movable with horizontal direction(x-direction) by motorized system for sectional gamma scanning and 3-dimensional tomography of fuel rod. So, gamma scanning for fuel rod can be detectable by x, y and rotation directions. It may be possible to obtain the radioactivities with radial and axial directions of pellet. This system is good for the series experiments with several positions. Operation of fuel bench and gamma detection program were linked each other by new program tools. It can control detection and bench moving automatically when gamma inspection of fuel rod is carried out with axial or radial positions. Some of electronic parts were added in PLC panel, and operating panel was re-designed for the remote control. To operate the fuel bench by computer, AD converter and some I/O cards were installed in computer. All of software were developed in Windows-XP system instead of DOS system. Control programs were made by visual-C language. After upgrade of system, DUPIC fuel which was irradiated in HANARO research reactor was detected by gamma scanning. The results were good and operation of gamma scanning showed reduced inspection time and easy control of data on series of detection with axial positions. With consideration of ECT(Eddy Current Test) installation, the computer program and hardware were set up as well. But ECT is not installed yet, so we have to check abnormal situation of program and hardware system. It is planned to install ECT in 2007.

  17. Evaluation of the thermal-hydraulic response and fuel rod thermal and mechanical deformation behavior during the power burst facility test LOC-3. [PWR

    Energy Technology Data Exchange (ETDEWEB)

    Yackle, T.R.; MacDonald, P.E.; Broughton, J.M.

    1980-01-01

    An evaluation of the results from the LOC-3 nuclear blowdown test conducted in the Power Burst Facility is presented. The test objective was to examine fuel and cladding behavior during a postulated cold leg break accident in a pressurized water reactor (PWR). Separate effects of rod internal pressure and the degree of irradiation were investigated in the four-rod test. Extensive cladding deformation (ballooning) and failure occurred during blowdown. The deformation of the low and high pressure rods was similar; however, the previously irradiated test rod deformed to a greater extent than a similar fresh rod exposed to identical system conditions.

  18. Preliminary Content Evaluation of the North Anna High Burn-Up Sister Fuel Rod Segments for Transportation in the 10-160B and NAC-LWT

    Energy Technology Data Exchange (ETDEWEB)

    Ketusky, E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-08-09

    The U.S. Department of Energy’s (DOE’s) Used Fuel Disposition Campaign (UFDC) Program has transported high-burnup nuclear sister fuel rods from a commercial nuclear power plant for purposes of evaluation and testing. The evaluation and testing of high-burnup used nuclear fuel is integral to DOE initiatives to collect information useful in determining the integrity of fuel cladding for future safe transportation of the fuel, and for determining the effects of aging, on the integrity of UNF subjected to extended storage and subsequent transportation. The UFDC Program, in collaboration with the U.S. Nuclear Regulatory Commission and the commercial nuclear industry, has obtained individual used nuclear fuel rods for testing. The rods have been received at Oak Ridge National Laboratory (ORNL) for both separate effects testing (SET) and small-scale testing (SST). To meet the research objectives, testing on multiple 6 inch fuel rod pins cut from the rods at ORNL will be performed at Pacific Northwest National Laboratory (PNNL). Up to 10 rod equivalents will be shipped. Options were evaluated for multiple shipments using the 10-160B (based on 4.5 rod equivalents) and a single shipment using the NAC-LWT. Based on the original INL/Virginia Power transfer agreement, the rods are assumed to 152 inches in length with a 0.374-inch diameter. This report provides a preliminary content evaluation for use of the 10-160B and NAC-LWT for transporting those fuel rod pins from ORNL to PNNL. This report documents the acceptability of using these packagings to transport the fuel segments from ORNL to PNNL based on the following evaluations: enrichment, A2 evaluation, Pu-239 FGE evaluation, heat load, shielding (both gamma and neutron), and content weight/structural evaluation.

  19. Characterization of a suspect nuclear fuel rod in a case of illegal international traffic of fissile material.

    Science.gov (United States)

    Capannesi, G; Vicini, C; Rosada, A; Avino, P

    2010-06-15

    This case study describes the characterization of a suspect rod of nuclear fuel seized in Italy: on request of the coroner, the characterization concerned the kind and the conditions of the rod, the amount and the specific characteristics of the species present in it, with particular attention to their possible use chemical and/or nuclear plants. The methodology used was based on radiochemical analyses (gammagraphic and gamma-spectrometry) whereas the comparison was performed by means of a fuel reference element working in the TRIGA nuclear reactor at Research Center of ENEA-Casaccia. The results show clearly how the exhibit was an element of nuclear fuel, how long it was irradiated, and the amount of (239)Pu produced and the (235)U consumed. Finally, even if the seized rod was briefly radiated at the "zero power" and traces of fission products and plutonium were found, it would be still usable as "fresh" fuel in a reactor type TRIGA if it had not been intercepted by Italian police authorities.

  20. Polydimethylsiloxane Rods for the Passive Sampling of Pesticides in Surface Waters

    Directory of Open Access Journals (Sweden)

    Jérôme Randon

    2013-09-01

    Full Text Available In this work, the low cost synthesis of polydimethylsiloxane (PDMS rods is described, and the performances of this new passive sampling device (in laboratory and in situ are compared to the passive stir bar sorptive extraction (SBSE for the monitoring of pesticides from different classes (herbicides, insecticides and fungicides in surface waters. The influence of synthesis parameters of PDMS rods (i.e., heating temperature, heating time and relative amount of curing agent were assessed regarding their efficiency for the extraction of the target pesticides through a Hadamard’s experimental design. This allowed the determination of the effect of the three parameters on the sorption of pesticides within four experiments. Thus, specific conditions were selected for the synthesis of the PDMS rods (heating at 80 °C for 2 h with 10% of curing agent. Laboratory experiments led to similar to lower extraction recovery in the PDMS rods in comparison with passive SBSE, depending on the pesticide. The in situ application demonstrated the efficiency of the PDMS rods for the passive sampling of the target pesticides in river water, although lower amounts of pesticides were recovered in comparison with passive SBSE. So, these very low cost PDMS rods could be used as an alternative to passive SBSE for large-scale monitoring campaigns.

  1. ROBOT3: a computer program to calculate the in-pile three-dimensional bowing of cylindrical fuel rods (AWBA Development Program)

    Energy Technology Data Exchange (ETDEWEB)

    Kovscek, S.E.; Martin, S.E.

    1982-10-01

    ROBOT3 is a FORTRAN computer program which is used in conjunction with the CYGRO5 computer program to calculate the time-dependent inelastic bowing of a fuel rod using an incremental finite element method. The fuel rod is modeled as a viscoelastic beam whose material properties are derived as perturbations of the CYGRO5 axisymmetric model. Fuel rod supports are modeled as displacement, force, or spring-type nodal boundary conditions. The program input is described and a sample problem is given.

  2. External Attachment of Titanium Sheathed Thermocouples to Zirconium Nuclear Fuel Rods For The Loss-Of-Fluid-Test (LOFT) Reactor

    Science.gov (United States)

    Welty, Richard K.

    1980-10-01

    The Exxon Nuclear Company, Inc. acting as a Subcontractor to EG&G Idaho Inc.3 Idaho National Engineering Laboratory, Idaho Falls, Idaho, has developed a welding process to attach titanium sheathed thermocouples to the outside of the zircaloy clad fuel rods. The fuel rods and thermocouples are used to test simulated loss-of-coolant-accident (LOCA) conditions in a pressurized water reactor (LOFT Reactor, Idaho National Laboratory). The design goals were to (1) reliably attach thermocouples to the zircaloy fuel rods, (2) achieve or exceed a life expectancy of 6,000 hours of reactor operation in a borated water environment of 316°C at 2260 psi, (3) provide and sustain repeatable physical and metallurgical properties in the instrumented rods subjected to transient temperatures up to 1538°C with blowdown, shock, loading, and fast quench. A laser beam was selected as the optimum welding process because of the extremely high energy input per unit volume that can be achieved allowing local fusion of a small area irrespective of the difference in material thickness to be joined. A commercial pulsed laser and energy control system was installed along with specialized welding fixtures. Laser room facility requirements and tolerances were established. Performance qualifications and detailed welding procedures were also developed. Product performance tests were conducted to assure that engineering design requirements could be met on a production basis. Irradiation tests showed no degradation of thermocouples or weld structure. Fast thermal cycle and heater rod blowdown reflood tests were made to subject the weldments to high temperatures, high pressure steam, and fast water quench cycles. From the behavior of these tests, it was concluded that the attachment welds would survive a series of reactor safety tests.

  3. Power Burst Facility: U(18)O2-CaO-ZrO2 Fuel Rods in Water

    Energy Technology Data Exchange (ETDEWEB)

    Jose Ignacio Marquez Damian; Alexis Weir; Valeria L. Putnam; John D. Bess

    2009-09-01

    The Power Burst Facility (PBF) reactor operated from 1972 to 1985 on the SPERT Area I of the Idaho National Laboratory, then known as Nuclear Reactor Test Station. PBF was designed to provide experimental data to aid in defining thresholds for and modes of failure under postulated accident conditions. PBF reactor startup testing began in 1972. This evaluation focuses on two operational loading tests, chronologically numbered 1 and 2, published in a startup-test report in 1974 [1]. Data for these tests was used by one of the authors to validate a MCNP model for criticality safety purposes [2]. Although specific references to original documents are kept in the text, all the reactor parameters and test specific data presented here was adapted from that report. The tests were performed with operational fuel loadings, a stainless steel in-pile tube (IPT) mockup, a neutron source, four pulse chambers, two fission chambers, and one ion chamber. The reactor's four transition rods (TRs) and control rods (CRs) were present but TR boron was completely withdrawn below the core and CR boron was partially withdrawn above the core. Test configurations differ primarily in the number of shim rods, and consequently the number of fuel rods included in the core. The critical condition was approached by incrementally and uniformly withdrawing CR boron from the core. Based on the analysis of the experimental data and numerical calculations, both experiments are considered acceptable as criticality safety benchmarks.

  4. Power Burst Facility: U(18)O2-CaO-ZrO2 Fuel Rods in Water

    Energy Technology Data Exchange (ETDEWEB)

    Jose Ignacio Marquez Damian; Alexis Weir; Valeria L. Putnam; John D. Bess

    2009-09-01

    The Power Burst Facility (PBF) reactor operated from 1972 to 1985 on the SPERT Area I of the Idaho National Laboratory, then known as Nuclear Reactor Test Station. PBF was designed to provide experimental data to aid in defining thresholds for and modes of failure under postulated accident conditions. PBF reactor startup testing began in 1972. This evaluation focuses on two operational loading tests, chronologically numbered 1 and 2, published in a startup-test report in 1974 [1]. Data for these tests was used by one of the authors to validate a MCNP model for criticality safety purposes [2]. Although specific references to original documents are kept in the text, all the reactor parameters and test specific data presented here was adapted from that report. The tests were performed with operational fuel loadings, a stainless steel in-pile tube (IPT) mockup, a neutron source, four pulse chambers, two fission chambers, and one ion chamber. The reactor's four transition rods (TRs) and control rods (CRs) were present but TR boron was completely withdrawn below the core and CR boron was partially withdrawn above the core. Test configurations differ primarily in the number of shim rods, and consequently the number of fuel rods included in the core. The critical condition was approached by incrementally and uniformly withdrawing CR boron from the core. Based on the analysis of the experimental data and numerical calculations, both experiments are considered acceptable as criticality safety benchmarks.

  5. Bending testing and characterization of surrogate nuclear fuel rods made of Zircaloy-4 cladding and aluminum oxide pellets

    Science.gov (United States)

    Wang, Hong; Wang, Jy-An John

    2016-10-01

    Behavior of surrogate nuclear fuel rods made of Zircaloy-4 (Zry-4) cladding with alumina pellets under reversed cyclic bending was studied. Tests were performed under load or moment control at 5 Hz. The surrogate rods fractured under moment amplitudes greater than 10.16 Nm with fatigue lives between 2.4 × 103 and 2.2 × 106 cycles. Fatigue response of Zry-4 cladding was characterized by using flexural rigidity. Degradation of flexural rigidity was shown to depend on the moment and the prefatigue condition of specimens. Pellet-to-pellet interface (PPI), pellet-to-cladding interface (PCI), and pellet condition affect surrogate rod failure. Both debonding of PPI/PCI and pellet fracturing contribute to surrogate rod bending fatigue. The effect of sensor spacing on curvature measurement using three-point deflections was studied; the method based on effective gauge length is effective in sensor spacing correction. The database developed and the understanding gained in this study can serve as input to analysis of SNF (spent nuclear fuel) vibration integrity.

  6. CFD modelling of supercritical water flow and heat transfer in a 2 × 2 fuel rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Podila, Krishna, E-mail: krishna.podila@cnl.ca; Rao, Yanfei, E-mail: yanfei.rao@cnl.ca

    2016-05-15

    Highlights: • Bare and wire wrapped 2 × 2 fuel rod bundles were modelled with CFD. • Sensitivity of predictions to SST k–ω, v{sup 2}–f and turbulent Prandtl number was tested. • CFD predictions were assessed with experimentally reported fuel wall temperatures. - Abstract: In the present assessment of the CFD code, two heat transfer experiments using water at supercritical pressures were selected: a 2 × 2 rod bare bundle; and a 2 × 2 rod wire-wrapped bundle. A systematic 3D CFD study of the fluid flow and heat transfer at supercritical pressures for the rod bundle geometries was performed with the key parameter being the fuel rod wall temperature. The sensitivity of the prediction to the steady RANS turbulence models of SST k–ω, v{sup 2}–f and turbulent Prandtl number (Pr{sub t}) was tested to ensure the reliability of the predicted wall temperature obtained for the current analysis. Using the appropriate turbulence model based on the sensitivity analysis, the mesh refinement, or the grid convergence, was performed for the two geometries. Following the above sensitivity analyses and mesh refinements, the recommended CFD model was then assessed against the measurements from the two experiments. It was found that the CFD model adopted in the current work was able to qualitatively capture the trends reported by the experiments but the degree of temperature rise along the heated length was underpredicted. Moreover, the applicability of turbulence models varied case-by-case and the performance evaluation of the turbulence models was primarily based on its ability to predict the experimentally reported fuel wall temperatures. Of the two turbulence models tested, the SST k–ω was found to be better at capturing the measurements at pseudo-critical and supercritical test conditions, whereas the v{sup 2}–f performed better at sub-critical test conditions. Along with the appropriate turbulence model, CFD results were found to be particularly sensitive to

  7. Studying the vibration and random hydrodynamic loads on the fuel rods bundles in the fuel assemblies of the reactor installations used at nuclear power stations equipped with VVER reactors

    Science.gov (United States)

    Solonin, V. I.; Perevezentsev, V. V.

    2012-05-01

    Random hydrodynamic loads causing vibration of fuel rod bundles in a turbulent flow of coolant are obtained from the results of pressure pulsation measurements carried out over the perimeter of the external row of fuel rods in the bundle of a full-scale mockup of a fuel assembly used in a second-generation VVER-440 reactor. It is shown that the turbulent flow structure is a factor determining the parameters of random hydrodynamic loads and the vibration of fuel rod bundles excited by these loads. The results from a calculation of random hydrodynamic loads are used for estimating the vibration levels of fuel rod bundles used in prospective designs of fuel assemblies for VVER reactors.

  8. DIONISIO 2.0: New version of the code for simulating a whole nuclear fuel rod under extended irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Soba, Alejandro, E-mail: soba@cnea.gov.ar; Denis, Alicia

    2015-10-15

    Highlights: • A new version of the DIONISIO code is developed. • DIONISIO is devoted to simulating the behavior of a nuclear fuel rod in operation. • The formerly two-dimensional simulation of a pellet-cladding segment is now extended to the whole rod length. • An acceptable and more realistic agreement with experimental data is obtained. • The prediction range of our code is extended up to average burnup of 60 MWd/kgU. - Abstract: The version 2.0 of the DIONISIO code, that incorporates diverse new aspects, has been recently developed. One of them is referred to the code architecture that allows taking into account the axial variation of the conditions external to the rod. With this purpose, the rod is divided into a number of axial segments. In each one the program considers the system formed by a pellet and the corresponding cladding portion and solves the numerous phenomena that take place under the local conditions of linear power and coolant temperature, which are given as input parameters. To do this a bi-dimensional domain in the r–z plane is considered where cylindrical symmetry and also symmetry with respect to the pellet mid-plane are assumed. The results obtained for this representative system are assumed valid for the complete segment. The program thus produces in each rod section the values of the temperature, stress, strain, among others as outputs, as functions of the local coordinates r and z. Then, the general rod parameters (internal rod pressure, amount of fission gas released, pellet stack elongation, etc.) are evaluated. Moreover, new calculation tools designed to extend the application range of the code to high burnup, which were reported elsewhere, have also been incorporated to DIONISIO 2.0 in recent times. With these improvements, the code results are compared with some 33 experiments compiled in the IFPE data base, that cover more than 380 fuel rods irradiated up to average burnup levels of 40–60 MWd/kgU. The results of these

  9. Data summary report for the destructive examination of Rods G7, G9, J8, I9, and H6 from Turkey Point Fuel Assembly B17

    Energy Technology Data Exchange (ETDEWEB)

    Davis, R B; Pasupathi, V

    1981-04-01

    Destructive examination results of five spent fuel rods from a Turkey Point Unit 3 pressurized water reactor are reported. Examinations included fission gas analysis, cladding hydrogen content analysis, fuel burnup analysis, metallographic examination, autoradiography and shielded electron microprobe analysis. All rods were found to be of sound integrity with an average burnup of 27 GWd/MTU and a 0.3% fission gas release.

  10. Advances in Forecasting and Prevention of Resonances Between Coolant Acoustical Oscillations and Fuel Rod Vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Proskuryakov, Konstantin Nicolaevich [NPP, NPEI, 14, Krasnokazarmennaya str. Moscow, 111250 (Russian Federation)

    2009-06-15

    To prevent the appearance of the conditions for resonance interaction between the fluid flow and the reactor internals (RI), fuel rod (FR ) and fuel assemblies (FA) it is necessary to de-tune Eigen frequency of coolant pressure oscillations (EFCPO) and natural frequency of mechanical element's oscillations and also of the system which is formed by the comprising of these elements. Other words it is necessary to de-tune acoustic resonance frequency and natural frequencies of RI, FR and FA. While solving these problems it is necessary to have a theoretical and settlement substantiation of an oscillation frequency band of the coolant outside of which there is no resonant interaction with structure vibrations. The presented work is devoted to finding the solution of this problem. There are results of an estimation of width of such band as well as the examples of a preliminary quantitative estimation of Q - factors of coolant acoustic oscillatory circuit formed by the equipment of the NPP. Abnormal growth of intensity of pressure pulsations in a mode with definite value of reactor capacity have been found out by measurements on VVER - 1000 reactor. This phenomenon has been found out casually and its original reason had not been identified. Paper shows that disappearance of this effect could be reached by realizing outlet of EFCPO from so-called, pass bands of frequencies (PBF). PBF is located symmetrical on both parties from frequency of own oscillations of FA. Methods, algorithms of calculations and quantitative estimations are developed for EFCPO, Q and PBF in various modes of operation NPP with VVER-1000. Results of calculations allow specifying area of resonant interaction EFCPO with vibrations of FR, FA and a basket of reactor core. For practical realization of the received results it is offered to make corresponding additions to the design documentation and maintenance instructions of the equipment of the NPP with VVER-1000. The improvement of these documents

  11. COMPARATIVE ANALYSIS OF STRUCTURAL CHANGES IN U-MO DISPERSED FUEL OF FULL-SIZE FUEL ELEMENTS AND MINI-RODS IRRADIATED IN THE MIR REACTOR

    Directory of Open Access Journals (Sweden)

    ALEKSEY. L. IZHUTOV

    2013-12-01

    The full-size fuel rods were irradiated up to an average burnup of ∼ 60%235U; the mini-rods were irradiated to an average burnup of ∼ 85%235U. The presented data show a significant increase of the void fraction in the U-Mo alloy as the U-235 burnup rises from ∼ 40% up to ∼ 85%. The effect of irradiation test conditions and U-235 burnup were analyzed with regard to the formation of an interaction layer between the matrix and fuel particles as well as generation of porosity in the U-Mo alloy. Shown here are changes in distribution of U fission products as the U-235 burnup increases from ∼ 40% up to ∼ 85%.

  12. Surface traction and the dynamics of elastic rods at low Reynolds number

    Science.gov (United States)

    Strawbridge, Eva M.; Wolgemuth, Charles W.

    2012-09-01

    Molecular and cell biological processes often use proteins and structures that are significantly longer in one dimension than they are in the other two, for example, DNA, actin, and bacterial flagella. The dynamics of these structures are the consequence of the balance between the elastic forces from the structure itself and viscous forces from the surrounding fluid. Typically, the motion of these filamentary objects is described using variations of the Kirchhoff rod equations with resistive forces from the fluid treated as body forces acting on the centerline. In reality, though, these forces are applied to the surface of the filament; however, the standard derivation of the Kirchhoff equations ignores surface traction stresses. Here, we rederive the Kirchhoff rod equations in the presence of resistive traction stresses and determine the conditions under which treating the drag forces as body forces is reasonable. We show that in most biologically relevant cases the standard implementation of resistive forces into the Kirchhoff rod equations is applicable; however, we note one particular biological system where the Kirchhoff rod formalism may not apply.

  13. Microscopic study of surface degradation of glass fiber-reinforced polymer rods embedded in concrete castings subjected to environmental conditioning

    Energy Technology Data Exchange (ETDEWEB)

    Bank, L.C. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Civil and Environmental Engineering; Puterman, M. [Technion, Haifa (Israel). National Building Research Inst.

    1997-12-31

    The surface degradation of glass fiber-reinforced polymer (GFRP) pultruded rods when embedded in concrete castings and subjected to environmental conditioning is discussed in this paper. Investigation of the degradation of the GFRP rods were performed using optical microscopy and scanning electron microscopy (SEM). Unidirectionally reinforced pultruded rods (6.3- and 12.7-mm diameters) containing E-glass fibers in polyester and vinylester matrices were conditioned at standard laboratory conditions (21 C, 65% relative humidity) or submerged in aqueous solutions (tap water) at 80 C for durations of 14 and 84 days. Observations of the surfaces and cross-sections of the rods by optical microscopy and SEM revealed a variety of degradation phenomena. Embedded hygrothermally conditioned rods were found to have developed surface blisters of different sizes and depths. SEM studies of the surface revealed degradation of the polymer matrix material and exposure and degradation of the fibers close to the surface of the rods. The rods with the vinylester resin matrix showed less extensive degradation than those with the polyester resin matrix; however, the degradation characteristics of the two types of rods appear to be similar.

  14. Probing anisotropic surface properties and interaction forces of chrysotile rods by atomic force microscopy and rheology.

    Science.gov (United States)

    Yang, Dingzheng; Xie, Lei; Bobicki, Erin; Xu, Zhenghe; Liu, Qingxia; Zeng, Hongbo

    2014-09-16

    Understanding the surface properties and interactions of nonspherical particles is of both fundamental and practical importance in the rheology of complex fluids in various engineering applications. In this work, natural chrysotile, a phyllosilicate composed of 1:1 stacked silica and brucite layers which coil into cylindrical structure, was chosen as a model rod-shaped particle. The interactions of chrysotile brucite-like basal or bilayered edge planes and a silicon nitride tip were measured using an atomic force microscope (AFM). The force-distance profiles were fitted using the classical Derjaguin-Landau-Verwey-Overbeek (DLVO) theory, which demonstrates anisotropic and pH-dependent surface charge properties of brucite-like basal plane and bilayered edge surface. The points of zero charge (PZC) of the basal and edge planes were estimated to be around pH 10-11 and 6-7, respectively. Rheology measurements of 7 vol % chrysotile (with an aspect ratio of 14.5) in 10 mM NaCl solution showed pH-dependent yield stress with a local maximum around pH 7-9, which falls between the two PZC values of the edge and basal planes of the rod particles. On the basis of the surface potentials of the edge and basal planes obtained from AFM measurements, theoretical analysis of the surface interactions of edge-edge, basal-edge, and basal-basal planes of the chrysotile rods suggests the yield stress maximum observed could be mainly attributed to the basal-edge attractions. Our results indicate that the anisotropic surface properties (e.g., charges) of chrysotile rods play an important role in the particle-particle interaction and rheological behavior, which also provides insight into the basic understanding of the colloidal interactions and rheology of nonspherical particles.

  15. Basic research and industrialization of CANDU advanced fuel - Effect of transverse convex curvature on boiling heat transfer and ONB point of nucleate fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyung Chun; Lee, Young; Lee, Sung Hong [Pusan National University, Pusan (Korea)

    2000-04-01

    Recently, the effect of convex curvature on heat transfer should not be ignored when the radius of curvature tends to be small and/or associated with high heat transfer rate cases. Both analytical and experimental studies were performed to prove the effect of transverse convex curvature on the boiling heat transfer in concentric annuli flows. The effect of the transverse convex surface curvature on ONB are studied analytically in the case of reactor and evaporator. It is seen that the inner wall heat flux depends on R/sub i/, Rc, Re, Pr, {alpha}, and the {theta} of working fluid. An experimental study on the incipience of nucleate boiling is performed as a verification ad extension of previous analyses. Through flow visualization, the results show that the most dominant parameter to affect the heat flux at ONB is found to be the surface curvature. The heat flux data at ONB increases with the Re and the subcooling, and the effect of subcooling on ONB becomes smaller with decreasing Re. The heat flux at ONB increases rapidly as increase in {alpha} due to higher convective motion of bulk flow. Comparison between both results are accomplished with respect to the relative enhancement due to the convex curvature. The relative heat transfer enhancement ratio shows a good agreement between theory and experiment qualitatively and quantitatively. In conclusion, the obtained results suggest that the effect transverse convex curvature appears significantly in the boiling heat transfer. Therefore, it can be clearly expected that the effect should be more strong at the case of critical heat flux condition which is the most important design goal of the advanced nuclear fuel rods. 30 refs., 78 figs. (Author)

  16. MMP20 Promotes a Smooth Enamel Surface, a Strong DEJ, and a Decussating Enamel Rod Pattern

    Science.gov (United States)

    Bartlett, John D.; Skobe, Ziedonis; Nanci, Antonio; Smith, Charles E.

    2012-01-01

    Mutations of the Matrix metalloproteinase-20 (MMP20, enamelysin) gene cause autosomal recessive amelogenesis imperfecta and Mmp20 ablated mice also have malformed dental enamel. Here we show that Mmp20 null mouse secretory stage ameloblasts maintained a columnar shape and were present as a single layer of cells. However, the null maturation stage ameloblasts covered extraneous nodules of ectopic calcified material formed at the enamel surface. Remarkably, nodule formation occurs in null mouse enamel when MMP20 is normally no longer expressed. The malformed enamel in Mmp20 null teeth was loosely attached to the dentin and the entire enamel layer tended to separate from the dentin indicative of a faulty DEJ. The enamel rod pattern was also altered in Mmp20 null mice. Each enamel rod is formed by a single ameloblast and is a mineralized record of the migration path of the ameloblast that formed it. The Mmp20 null mouse enamel rods were grossly malformed or were absent indicating that the ameloblasts do not migrate properly when backing away from the DEJ. Thus, MMP20 is required for ameloblast cell movement necessary to form the decussating enamel rod patterns, for the prevention of ectopic mineral formation, and to maintain a functional DEJ. PMID:22243247

  17. Unsupervised Classification of Surface Defects in Wire Rod Production Obtained by Eddy Current Sensors

    Directory of Open Access Journals (Sweden)

    Sergio Saludes-Rodil

    2015-04-01

    Full Text Available An unsupervised approach to classify surface defects in wire rod manufacturing is developed in this paper. The defects are extracted from an eddy current signal and classified using a clustering technique that uses the dynamic time warping distance as the dissimilarity measure. The new approach has been successfully tested using industrial data. It is shown that it outperforms other classification alternatives, such as the modified Fourier descriptors.

  18. 3D modeling of missing pellet surface defects in BWR fuel

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, B.W., E-mail: Benjamin.Spencer@inl.gov; Williamson, R.L.; Stafford, D.S.; Novascone, S.R.; Hales, J.D.; Pastore, G.

    2016-10-15

    Highlights: • A global/local analysis procedure for missing pellet surface defects is proposed. • This is applied to defective BWR fuel under blade withdrawal and high power ramp conditions. • Sensitivity of the cladding response to key model parameters is studied. - Abstract: One of the important roles of cladding in light water reactor fuel rods is to prevent the release of fission products. To that end, it is essential that the cladding maintain its integrity under a variety of thermal and mechanical loading conditions. Local geometric irregularities in fuel pellets caused by manufacturing defects known as missing pellet surfaces (MPS) can in some circumstances lead to elevated cladding stresses that are sufficiently high to cause cladding failure. Accurate modeling of these defects can help prevent these types of failures. The BISON nuclear fuel performance code developed at Idaho National Laboratory can be used to simulate the global thermo-mechanical fuel rod behavior, as well as the local response of regions of interest, in either 2D or 3D. In either case, a full set of models to represent the thermal and mechanical properties of the fuel, cladding and plenum gas is employed. A procedure for coupling 2D full-length fuel rod models to detailed 3D models of the region of the rod containing a MPS defect is detailed here. The global and local model each contain appropriate physics and behavior models for nuclear fuel. This procedure is demonstrated on a simulation of a boiling water reactor (BWR) fuel rod containing a pellet with an MPS defect, subjected to a variety of transient events, including a control blade withdrawal and a ramp to high power. The importance of modeling the local defect using a 3D model is highlighted by comparing 3D and 2D representations of the defective pellet region. Parametric studies demonstrate the effects of the choice of gaseous swelling model and of the depth and geometry of the MPS defect on the response of the cladding

  19. Angra-1 reactor core simulation with reduced diameter fuel rods; Simulacao do nucleo de Angra-1 com combustiveis de menor diametro de vareta

    Energy Technology Data Exchange (ETDEWEB)

    Sadde, Luciano M; Faria, Eduardo F.; Sakai, Massao; Gomes, Sydney da S. [Industrias Nucleares do Brasil SA, Resende, RJ (Brazil)

    2000-07-01

    From the neutronic point of view, it is advantageous to use fuel elements with narrower rod diameter at Angra-1 PWR, since the reactivity level increases, and that happens mainly for higher enrichments than the ones used up to now. This fact is due to the higher moderator/fuel ratio, leading to a stronger neutron thermalization. In order to quantify this effect, the nodal core MEDIUM/SAV90 has been employed to simulate Angra-1 cycles from the present until the equilibrium cycle. The actual fuel element design has been maintained in this report, with exception of fuel rods diameter, reduced to 9 mm. Results have shown a higher reactivity and final burnup for the reduced diameter fuel rods, producing less waste for final disposal. However, the combined effect of higher elements reactivity and burnup made difficult the cycle-by-cycle fuel reload optimization. Preliminary results show possible advantages of using reduced diameter fuel rods in reload schemes type 'stop and go', but not being recommendable for extended cycles. (author)

  20. Growth of Hierarchically Structured High-Surface Area Alumina on FeCralloy® Rods

    Institute of Scientific and Technical Information of China (English)

    Chandni Rallan; Arthur Garforth⁎

    2014-01-01

    The formation of metastable alumina phases due to the oxidation of commercial FeCralloy® rods (0.5 mm thickness) at various temperatures and time periods has been examined. This structured layer acts as an anchor to bind additional coatings of alumina via wash-coat techniques, thereby improving the layer thickness and increasing adhesion of the catalytic surface. Optimisation of the layer thickness and catalytic properties were conducted, using a range of analytical systems [scanning electron microscope (SEM), energy dispersive X-ray (EDX) and X-ray diffraction (XRD)]. The modified FeCral oy® rods were tested in a fixed bed reactor rig to assess the impact on yield for the dehydrogenation of methylcyclohexane.

  1. A new fast neutron collar for safeguards inspection measurements of fresh low enriched uranium fuel assemblies containing burnable poison rods

    Science.gov (United States)

    Evans, Louise G.; Swinhoe, Martyn T.; Menlove, Howard O.; Schwalbach, Peter; Baere, Paul De; Browne, Michael C.

    2013-11-01

    Safeguards inspection measurements must be performed in a timely manner in order to detect the diversion of significant quantities of nuclear material. A shorter measurement time can increase the number of items that a nuclear safeguards inspector can reliably measure during a period of access to a nuclear facility. In turn, this improves the reliability of the acquired statistical sample, which is used to inform decisions regarding compliance. Safeguards inspection measurements should also maintain independence from facility operator declarations. Existing neutron collars employ thermal neutron interrogation for safeguards inspection measurements of fresh fuel assemblies. A new fast neutron collar has been developed for safeguards inspection measurements of fresh low-enriched uranium (LEU) fuel assemblies containing gadolinia (Gd2O3) burnable poison rods. The Euratom Fast Collar (EFC) was designed with high neutron detection efficiency to make a fast (Cd) mode measurement viable whilst meeting the high counting precision and short assay time requirements of the Euratom safeguards inspectorate. A fast mode measurement reduces the instrument sensitivity to burnable poison rod content and therefore reduces the applied poison correction, consequently reducing the dependence on the operator declaration of the poison content within an assembly. The EFC non-destructive assay (NDA) of typical modern European pressurized water reactor (PWR) fresh fuel assembly designs have been simulated using Monte Carlo N-particle extended transport code (MCNPX) simulations. Simulations predict that the EFC can achieve 2% relative statistical uncertainty on the doubles neutron counting rate for a fast mode measurement in an assay time of 600 s (10 min) with the available 241AmLi (α,n) interrogation source strength of 5.7×104 s-1. Furthermore, the calibration range of the new collar has been extended to verify 235U content in variable PWR fuel designs in the presence of up to 32

  2. A particle assembly/constrained expansion (PACE) model for the formation and structure of porous metal oxide deposits on nuclear fuel rods in pressurized light water reactors

    Science.gov (United States)

    Brenner, Donald W.; Lu, Shijing; O'Brien, Christopher J.; Bucholz, Eric W.; Rak, Zsolt

    2015-02-01

    A new model is proposed for the structure and properties of porous metal oxide scales (aka Chalk River Unidentified Deposits (CRUD)) observed on the nuclear fuel rod cladding in Pressurized Water Reactors (PWR). The model is based on the thermodynamically-driven expansion of agglomerated octahedral nickel ferrite particles in response to pH and temperature changes in the CRUD. The model predicts that porous nickel ferrite with internal {1 1 1} surfaces is a thermodynamically stable structure under PWR conditions even when the free energy of formation of bulk nickel ferrite is positive. This explains the pervasive presence of nickel ferrite in CRUD, observed CRUD microstructures, why CRUD maintains its porosity, and variations in porosity within the CRUD observed experimentally. This model is a stark departure from decades of conventional wisdom and detailed theoretical analysis of CRUD chemistry, and defines new research directions for model validation, and for understanding and ultimately controlling CRUD formation.

  3. SCORE-EVET: a computer code for the multidimensional transient thermal-hydraulic analysis of nuclear fuel rod arrays. [BWR; PWR

    Energy Technology Data Exchange (ETDEWEB)

    Benedetti, R. L.; Lords, L. V.; Kiser, D. M.

    1978-02-01

    The SCORE-EVET code was developed to study multidimensional transient fluid flow in nuclear reactor fuel rod arrays. The conservation equations used were derived by volume averaging the transient compressible three-dimensional local continuum equations in Cartesian coordinates. No assumptions associated with subchannel flow have been incorporated into the derivation of the conservation equations. In addition to the three-dimensional fluid flow equations, the SCORE-EVET code ocntains: (a) a one-dimensional steady state solution scheme to initialize the flow field, (b) steady state and transient fuel rod conduction models, and (c) comprehensive correlation packages to describe fluid-to-fuel rod interfacial energy and momentum exchange. Velocity and pressure boundary conditions can be specified as a function of time and space to model reactor transient conditions such as a hypothesized loss-of-coolant accident (LOCA) or flow blockage.

  4. Investigation of the structure of debris beds formed from fuel rods fragmentation

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Duc-Hanh; Fichot, Florian; Topin, Vincent, E-mail: vincent.topin@irsn.fr

    2017-03-15

    This paper is a study of debris beds that can form in the core of a nuclear power plant under severe accident conditions. Such beds are formed of fragments of pellets and cladding remnants, as observed in the TMI-2 core. Many important issues are related with the morphology of those debris beds: are they coolable in case of water injection and how does molten corium progress through them if they are not coolable? The answers to those questions depend on the structure of the debris bed: porosity, number and arrangement of particles. In order to obtain relevant information, a numerical simulation of the formation of the debris bed is proposed. It relies on a granular approach of the type called “Contact Dynamics” to simulate the collapse of debris and their accumulation. Two different schemes of fuel pellet fragmentation are considered and simulations for different degrees of fragmentation of the pellets are performed. The results show that the number of axial cracks on fuel pellets strongly influences the final porosity of the debris bed. Porosities vary between 31% (less coolable cases) and 45% (similar to TMI-2 observations), with a most probable configuration around 41%. The specific surface of the bed is also evaluated. In the last part, a simple model is used to estimate the impact of the variation in geometry of the numeric debris beds on their flow properties. We show that the permeability and passability can vary respectively with a range of 30% and 15% depending on the number of fragment per pellet. The other benefits of the approach are finally discussed. Among them, the possibility to print 3D samples from the calculated images of debris beds appears as a promising perspective to perform experiments with realistic debris beds.

  5. Thermomechanical analysis of fuel rods during transitory events using the RAMONA and FETMA codes; Analisis termomecanico de barras combustibles durante eventos transitorios usando los codigos RAMONA y FETMA

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez L, H. [ININ, Departamento de Sistemas Nucleares, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)], e-mail: hector.hernandez@inin.gob.mx

    2009-10-15

    In National Institute of Nuclear Research, the fuel management system (FMS) has been used by long time to simulate the BWR operation in stationary state, as well as during a transitory event. To evaluate the thermomechanical behavior of a fuel element was created and interface between the FMS codes and the fuel element thermo mechanical analysis (FETMA) code properly developed and implemented. In this work, the results of thermomechanical behavior of fuel rods that compose the hot channel during the simulation of a transitory event of a BWR are shown. The transitory events considered in this work are a load rejection and failure in controller of feed water, which are events more important that can to occur in a BWR. The results show that during the developed conditions by both transitory events some failure is not presented in fuel rods. Also, that the transitory event of load rejection is more claimant in security terms that of controller failure of feed water. (Author)

  6. Non-destructive methods of control of thermo-physical properties of fuel rods

    Science.gov (United States)

    Kruglov, A. B.; Kruglov, V. B.; Kharitonov, V. S.; Struchalin, P. G.; Galkin, A. G.

    2017-01-01

    Information about the change of thermal properties of the fuel elements needed for a successful and safe operation of the nuclear power plant. At present, the existing amount of information on the fuel thermal conductivity change and “fuel-shell” thermal resistance is insufficient. Also, there is no technique that would allow for the measurement of these properties on the non-destructive way of irradiated fuel elements. We propose a method of measuring the thermal conductivity of the fuel in the fuel element and the contact thermal resistance between the fuel and the shell without damaging the integrity of the fuel element, which is based on laser flash method. The description of the experimental setup, implementing methodology, experiments scheme. The results of test experiments on mock-ups of the fuel elements and their comparison with reference data, as well as the results of numerical modeling of thermal processes that occur during the measurement. Displaying harmonization of numerical calculation with the experimental thermograms layout shell portions of the fuel cell, confirming the correctness of the calculation model.

  7. A preliminary approach to the extension of the Transuranus code to the fuel rod performance analysis of HLM-cooled nuclear reactors

    Energy Technology Data Exchange (ETDEWEB)

    Luzzi, L.; Botazzoli, P.; Devita, M.; Di Marcello, V.; Pastore, G. [Department of Energy, Politecnico di Milano, Enrico Fermi Center for Nuclear Studies - CeSNEF, via Ponzio 34/3, 20133 Milano (Italy)

    2010-07-01

    This paper briefly presents a preliminary modelling approach, aimed at the extension of the TRANSURANUS code to the fuel rod performance analysis of Heavy Liquid Metal (HLM) cooled nuclear reactors, with specific reference to the employment of the T91 steel as cladding material and of the liquid Lead-Bismuth Eutectic (LBE) as coolant. On the basis of literature indications, correlations for heat transfer to LBE, corrosion behaviour and thermo-mechanical properties of T91 are proposed, and some open issues are discussed in prospect of more reliable fuel rod performance analysis of HLM-cooled nuclear reactors. (authors)

  8. Thermoacoustic enhancements for nuclear fuel rods and other high temperature applications

    Energy Technology Data Exchange (ETDEWEB)

    Garrett, Steven L.; Smith, James A.; Kotter, Dale K.

    2017-05-09

    A nuclear thermoacoustic device includes a housing defining an interior chamber and a portion of nuclear fuel disposed in the interior chamber. A stack is disposed in the interior chamber and has a hot end and a cold end. The stack is spaced from the portion of nuclear fuel with the hot end directed toward the portion of nuclear fuel. The stack and portion of nuclear fuel are positioned such that an acoustic standing wave is produced in the interior chamber. A frequency of the acoustic standing wave depends on a temperature in the interior chamber.

  9. Turbulet flow in a model nuclear fuel rod bundle containing partial flow blockages

    Energy Technology Data Exchange (ETDEWEB)

    Creer, J.M.; Rowe, D.S.; Bates, J.M.; Sutey, A.M.

    1977-03-01

    Local velocity and turbulence intensity measurements were obtained with a laser Doppler anemometer near flow blockages in an unheated 7 x 7 rod bundle. Sleeve blockages were positioned on the center nine rods to create area reductions of 70 and 90 percent in the center four subchannels of the bundle. Experimental results indicated that severe flow disturbances existed downstream from the blockage clusters and showed that only minor disturbances can be expected upstream from the blockages. Recirculation zones for both 70 and 90 percent blockages were detected downstream from the blockage clusters and persisted for approximately three to five subchannel hydraulic diameters depending on blockage severity. The experimental velocity results obtained with blockage clusters located midway between grid spacers were successfully predicted using the COBRA computer program.

  10. Results of Post Irradiation Examinations of VVER Leaky Rods

    Energy Technology Data Exchange (ETDEWEB)

    Markov, D.; Perepelkin, S.; Polenok, V.; Zhitelev, V.; Mayorshina, G. [Head of Fuel Research Department, JSC ' SSC RIAR' , 433510, Dimitrovgrad-10, Ulyanovsk region (Russian Federation)

    2009-06-15

    The most important requirement imposed on fuel elements is to maintain integrity of fuel rod claddings under operation, storage and transportation, since it is directly related to the operational safety. However, failed rod claddings are sometimes observed under reactor operation. Identification and unloading of fuel assemblies with leaky rods from VVER is available only at the time of planned preventive maintenance. An unscheduled reactor shutdown due to the excess of coolant activity limit as well as a preterm unloading of the fuel assembly cause economic damage to nuclear plant. Therefore, models and calculation codes were developed to forecast coolant contamination and failed fuel rod behavior. Criteria based on calculations were set to determine the admissible number of the failed rods in core and the opportunity to continue the reactor operation or pre-term unloading of the fuel assembly with the failed rods. Nevertheless, to prevent the fuel rod failure (for unfailing operation) it is necessary to reveal disadvantages of the design, fabrication method and fuel operation conditions, and to eliminate defects. The most complete and significant information about spent fuel assemblies may be received following the post irradiation material examinations. In order to reveal failure origins and mechanism of changes in VVER fuel and failed rod cladding condition depending on the operation, the examinations of 12 VVER-1000 fuel assemblies and 3 VVER-440 fuel assemblies, operated under normal conditions up to the fuel burnup 13..47 MWd/kgU were carried out. To evaluate the rod cladding condition, reveal defects and determine their parameters, the ultrasonic control of cladding integrity, surface visual inspection, eddy current defectoscopy, measurement of geometrical parameters were applied. In separate cases we used the metallography, measured the hydrogen percentage and carried out the mechanical tests of o-ring samples. The pellet condition was evaluated in

  11. Automatic system of welding for nuclear fuel rods; Sistema automatico de soldadura para barras de combustible nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Romero G, M; Romero C, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1998-07-01

    The welding process of nuclear fuel must be realized in an inert gas environment (He) and constant flow of this. In order to reach these conditions it is necessary to do vacuum at the chamber and after it is pressurized with the noble gas (purge) twice in the welding chamber. The purge eliminates impurities that can provoke oxidation in the weld. Once the conditions for initiating the welding are gotten, it is necessary to draw a graph of the flow parameters, pressure, voltage and arc current and to analyse those conditions in which have been carried out the weld. The rod weld must be free of possible pores or cracks which could provoke rod leaks, so reducing the probability of these failures should intervene mechanical and metallurgical factors. Automatizing the process it allows to do reliable welding assuring that conditions have been performed, reaching a high quality welding. Visually it can be observed the welding process by means of a mimic which represents the welding system. There are the parameters acquired such as voltage, current, pressure and flow during the welding arc to be analysed later. (Author)

  12. Post-irradiation examination of prototype Al-64 wt% U{sub 3}Si{sub 2} fuel rods from NRU

    Energy Technology Data Exchange (ETDEWEB)

    Sears, D.F.; Primeau, M.F.; Buchanan, C.; Rose, D. [Chalk River Labs., Ontario (Canada)

    1997-08-01

    Three prototype fuel rods containing Al-64 wt% U{sub 3}Si{sub 2} (3.15 gU/cm{sup 3}) have been irradiated to their design burnup in the NRU reactor without incident. The fuel was fabricated using production-scale equipment and processes previously developed for Al-U{sub 3}Si fuel fabrication at Chalk River Laboratories, and special equipment developed for U{sub 3}Si{sub 2} powder production and handling. The rods were irradiated in NRU up to 87 at% U-235 burnup under typical driver fuel conditions; i.e., nominal coolant inlet temperature 37{degrees}C, inlet pressure 654 kPa, mass flow 12.4 L/s, and element linear power ratings up to 73 kW/m. Post-irradiation examinations showed that the fuel elements survived the irradiation without defects. Fuel core diametral increases and volumetric swelling were significantly lower than that of Al-61 wt% U{sub 3}Si fuel irradiated under similar conditions. This irradiation demonstrated that the fabrication techniques are adequate for full-scale fuel manufacture, and qualified the fuel for use in AECL`s research reactors.

  13. PWR-UO{sub 2} nuclear fuel criticality study: control rod effects on infinite neutron multiplication factor and spent fuel composition

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, R.V.; Pereira, C., E-mail: claubia@nuclear.ufmg.br; Silva, C.A.M.; Costa, A.L.; Veloso, M.A.F.; Oliveira, A.H. de

    2013-10-15

    Highlights: • A three-dimensional model of a PWR fuel were simulated. • Results using TRITON/T6-DEPL module in SCALE 6.0 and two libraries (238 and 44 groups) were compared. • Variations in the infinite neutron multiplication factor and the nuclides concentrations, both under control rod insertion effects were analysed. • Results show very good agreement with those published by OECD. -- Abstract: Deterministic and stochastic nuclear codes are software packages used to perform reactor physics calculations, especially in PWRs, the most common type of nuclear reactor currently in operation. The NEA Expert Group on Burn-up Credit Criticality Safety has published a Benchmark with results obtained from simulations of PWR-UO{sub 2} nuclear fuel. The same simulations were performed at DEN/UFMG with SCALE 6.0, a modular nuclear system code developed by Oak Ridge National Laboratory using two different neutron energy libraries (238 and 44 groups). The results obtained using a three-dimensional model with the T6-DEPL sequence of the TRITON module in SCALE 6.0 for spent fuel inventory and infinite neutron multiplication factor calculations show very good agreement with those published by the OECD. The main goal of this work is to validate the methodology at DEN/UFMG for future use in simulations related to Angra I, II and III Nuclear Power Plants.

  14. Effect of fission fragment on thermal conductivity via electrons with an energy about 0.5 MeV in fuel rod gap

    Directory of Open Access Journals (Sweden)

    F Golian

    2017-02-01

    Full Text Available The heat transfer process from pellet to coolant is one of the important issues in nuclear reactor. In this regard, the fuel to clad gap and its physical and chemical properties are effective factors on heat transfer in nuclear fuel rod discussion. So, the energy distribution function of electrons with an energy about 0.5 MeV in fuel rod gap in Busherhr’s VVER-1000 nuclear reactor was investigated in this paper. Also, the effect of fission fragments such as Krypton, Bromine, Xenon, Rubidium and Cesium on the electron energy distribution function as well as the heat conduction via electrons in the fuel rod gap have been studied. For this purpose, the Fokker- Planck equation governing the stochastic behavior of electrons in absorbing gap element has been applied in order to obtain the energy distribution function of electrons. This equation was solved via Runge-Kutta numerical method. On the other hand, the electron energy distribution function was determined by using Monte Carlo GEANT4 code. It was concluded that these fission fragments have virtually insignificant effect on energy distribution of electrons and therefore, on thermal conductivity via electrons in the fuel to clad gap. It is worth noting that this result is consistent with the results of other experiments. Also, it is shown that electron relaxation in gap leads to decrease in thermal conductivity via electrons

  15. Sodium-cooled fast reactor (SFR) fuel assembly design with graphite-moderating rods to reduce the sodium void reactivity coefficient

    Energy Technology Data Exchange (ETDEWEB)

    Won, Jong Hyuck; Cho, Nam Zin, E-mail: nzcho@kaist.ac.kr; Park, Hae Min; Jeong, Yong Hoon, E-mail: jeongyh@kaist.ac.kr

    2014-12-15

    Highlights: • The graphite rod-inserted SFR fuel assembly is proposed to achieve low sodium void reactivity. • The neutronics/thermal-hydraulics analyses are performed for the proposed SFR cores. • The sodium void reactivity is improved about 960–1030 pcm compared to reference design. - Abstract: The concept of a graphite-moderating rod-inserted sodium-cooled fast reactor (SFR) fuel assembly is proposed in this study to achieve a low sodium void reactivity coefficient. Using this concept, two types of SFR cores are analyzed; the proposed SFR type 1 core has new SFR fuel assemblies at the inner/mid core regions while the proposed SFR type 2 core has a B{sub 4}C absorber sandwich in the middle of the active core region as well as new SFR fuel assemblies at the inner/mid core regions. For the proposed SFR core designs, neutronics and thermal-hydraulic analyses are performed using the DIF3D, REBUS3, and the MATRA-LMR codes. In the neutronics analysis, the sodium void reactivity coefficient is obtained in various void situations. The two types of proposed core designs reduce the sodium void reactivity coefficient by about 960–1030 pcm compared to the reference design. However, the TRU enrichment for the proposed SFR core designs is increased. In the thermal hydraulic analysis, the temperature distributions are calculated for the two types of proposed core designs and the mass flow rate is optimized to satisfy the design constraints for the highest power generating assembly. The results of this study indicate that the proposed SFR assembly design concept, which adopts graphite-moderating rods which are inserted into the fuel assembly, can feasibly minimize the sodium void reactivity coefficient. Single TRU enrichment and an identical fuel slug diameter throughout the SFR core are also achieved because the radial power peak can be flattened by varying the number of moderating rods in each core region.

  16. Evaluation of alternative treatments for spent fuel rod consolidation wastes and other miscellaneous commercial transuranic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Ross, W.A.; Schneider, K.J.; Oma, K.H.; Smith, R.I.; Bunnell, L.R.

    1986-05-01

    Eight alternative treatments (and four subalternatives) are considered for both existing commercial transuranic wastes and future wastes from spent fuel consolidation. Waste treatment is assumed to occur at a hypothetical central treatment facility (a Monitored Retrieval Storage facility was used as a reference). Disposal in a geologic repository is also assumed. The cost, process characteristics, and waste form characteristics are evaluated for each waste treatment alternative. The evaluation indicates that selection of a high-volume-reduction alternative can save almost $1 billion in life-cycle costs for the management of transuranic and high-activity wastes from 70,000 MTU of spent fuel compared to the reference MRS process. The supercompaction, arc pyrolysis and melting, and maximum volume reduction alternatives are recommended for further consideration; the latter two are recommended for further testing and demonstration.

  17. Assessment of stainless steel 348 fuel rod performance against literature available data using TRANSURANUS code

    OpenAIRE

    Giovedi Claudia; Cherubini Marco; Abe Alfredo; D’Auria Francesco

    2016-01-01

    Early pressurized water reactors were originally designed to operate using stainless steel as cladding material, but during their lifetime this material was replaced by zirconium-based alloys. However, after the Fukushima Daiichi accident, the problems related to the zirconium-based alloys due to the hydrogen production and explosion under severe accident brought the importance to assess different materials. In this sense, initiatives as ATF (Accident Tolerant Fuel) program are considering di...

  18. A comparison of crud phases appearing on some Swedish BWR fuel rods using Laser Raman Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Hermansson, H.P. [Studsvik Nuclear AB, Nykoeping (Sweden)]|[Lulea Univ. of Technology (Sweden)

    2002-07-01

    Previous investigations showed that laser Raman spectroscopy (LRS) can be used as a phase specific analytical tool for radioactive fuel crud samples and also for details in the underlying layer of zirconium dioxide. It is relatively easy to record Raman spectra that discriminate between chemical phases for all crud oxides of interest. The method has therefore been recommended for crud investigations within the Swedish program. At ideal conditions the resolution is about 1 {mu}m, permitting detailed position determination of crud phases in the sample. Therefore LRS is a very good complement to X-ray diffraction (XRD). The methods for sample preparation and handling of radioactive crud samples for LRS turn out to be relatively simple. A detailed LRS study on fuel crud samples from Barsebaeck 2, Forsmark 2, Forsmark 3 and Ringhals 1 was performed in this work. All of those Swedish BWRs were operated at different conditions at the time of sampling. The chemistry regimes covered NWC, HWC and other variable conditions. Also different types of fuel, exposure times and sampling positions were selected. (authors)

  19. The Recovery of the Metal Insulation Cable in the Instrumentation of Nuclear Fuel Rod

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Chang Young; Ahn, Sung Ho; Sim, Bong Sik; Lee, Chul Yong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2010-10-15

    Mineral-insulated (MI) cables are widely used to prolong the instrumentation cable of instruments such as a thermocouple (TC), linear variable differential transformer (LVDT) and self-powered neutron detector (SPND), which are used to measure various irradiation characteristics of nuclear fuels and materials. MI cables are expected to be helpful for instrumentation of nuclear fuel and material irradiation because of their high electrical insulation, heat resistance and mechanical strength. The MI cable used to extend thermocouple wires is classified as the following: 1) For common metal types of thermocouples, the thermocouple extension wire is of substantially the same composition as the corresponding thermocouple type and it can offer advantages in cost or mechanical properties when used for the connection between a thermocouple and instruments. 2) For noble metal types of thermocouples, the thermocouple compensation wire is an entirely different alloy formulated to match the noble metal characteristics, which is necessary due to the high cost of noble metals. During the installation of an instrument, an MI cable damaged by impact must be recovered because it is difficult to change the entire thermocouple. And for MI cable recovery, it is necessary to develop the instrumentation technology of FTL. This paper described the experimental results of MI cable recovery, which consists of a removal test of the MI cable sheath and a joining test of the compensation of the wire and MI cable/ wire/compensation wire and sheath of MI cable/bushing, for carrying out irradiation tests of nuclear fuel and materials in the FTL facility of HANARO

  20. Anisotropic Azimuthal Power and Temperature distribution on FuelRod. Impact on Hydride Distribution

    Energy Technology Data Exchange (ETDEWEB)

    Motta, Arthur [Pennsylvania State Univ., State College, PA (United States); Ivanov, Kostadin [Pennsylvania State Univ., State College, PA (United States); Arramova, Maria [Pennsylvania State Univ., State College, PA (United States); Hales, Jason [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-04-29

    The degradation of the zirconium cladding may limit nuclear fuel performance. In the high temperature environment of a reactor, the zirconium in the cladding corrodes, releasing hydrogen in the process. Some of this hydrogen is absorbed by the cladding in a highly inhomogeneous manner. The distribution of the absorbed hydrogen is extremely sensitive to temperature and stress concentration gradients. The absorbed hydrogen tends to concentrate near lower temperatures. This hydrogen absorption and hydride formation can cause cladding failure. This project set out to improve the hydrogen distribution prediction capabilities of the BISON fuel performance code. The project was split into two primary sections, first was the use of a high fidelity multi-physics coupling to accurately predict temperature gradients as a function of r, θ , and z, and the second was to use experimental data to create an analytical hydrogen precipitation model. The Penn State version of thermal hydraulics code COBRA-TF (CTF) was successfully coupled to the DeCART neutronics code. This coupled system was verified by testing and validated by comparison to FRAPCON data. The hydrogen diffusion and precipitation experiments successfully calculated the heat of transport and precipitation rate constant values to be used within the hydrogen model in BISON. These values can only be determined experimentally. These values were successfully implemented in precipitation, diffusion and dissolution kernels that were implemented in the BISON code. The coupled output was fed into BISON models and the hydrogen and hydride distributions behaved as expected. Simulations were conducted in the radial, axial and azimuthal directions to showcase the full capabilities of the hydrogen model.

  1. Wavelength dependent neutron transmission and radiography investigations of the high temperature behaviour of materials applied in nuclear fuel and control rod claddings

    Science.gov (United States)

    Grosse, M.; Steinbrueck, M.; Kaestner, A.

    2011-09-01

    Neutron radiography was used for the investigation of the nuclear fuel and control rod cladding behaviour during steam oxidation under severe nuclear accident conditions. In order to verify the hypothesis that the unexpectedly high neutron cross-section found after oxidation of Zircaloy-4 in wet air containing 10% steam is caused by a strong hydrogen uptake, the wavelength dependence of the total macroscopic neutron cross-section of the specimens was measured. The characteristic dependence for hydrogen was not found, which is a proof that hydrogen is not absorbed significantly. The data agree mostly with the behaviour expected for β-Zr. Examinations of control rod simulators annealed until the failure in single-rod tests were performed. In order to separate the effect of the neutron absorber and control rod structure materials, radiographs taken with different neutron spectra were combined. This procedure clearly showed that the local melting resulting from the eutectic reaction between the stainless steel control rod cladding and the Zircaloy-4 guide tube is the reason for the failure.

  2. Wavelength dependent neutron transmission and radiography investigations of the high temperature behaviour of materials applied in nuclear fuel and control rod claddings

    Energy Technology Data Exchange (ETDEWEB)

    Grosse, M., E-mail: Mirco.Grosse@KIT.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, P.O. Box 3640, D-76021 Karlsruhe (Germany); Steinbrueck, M. [Karlsruhe Institute of Technology, Institute for Applied Materials, P.O. Box 3640, D-76021 Karlsruhe (Germany); Kaestner, A. [Department of Spallation Source, Paul Scherrer Institute (PSI), CH-5232 Villigen (Switzerland)

    2011-09-21

    Neutron radiography was used for the investigation of the nuclear fuel and control rod cladding behaviour during steam oxidation under severe nuclear accident conditions. In order to verify the hypothesis that the unexpectedly high neutron cross-section found after oxidation of Zircaloy-4 in wet air containing 10% steam is caused by a strong hydrogen uptake, the wavelength dependence of the total macroscopic neutron cross-section of the specimens was measured. The characteristic dependence for hydrogen was not found, which is a proof that hydrogen is not absorbed significantly. The data agree mostly with the behaviour expected for {beta}-Zr. Examinations of control rod simulators annealed until the failure in single-rod tests were performed. In order to separate the effect of the neutron absorber and control rod structure materials, radiographs taken with different neutron spectra were combined. This procedure clearly showed that the local melting resulting from the eutectic reaction between the stainless steel control rod cladding and the Zircaloy-4 guide tube is the reason for the failure.

  3. Critical Configuration and Physics Measurements for Assemblies of U(93.15)O2 Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2013-03-01

    A series of critical experiments were completed in 1962-1965 at Oak Ridge National Laboratory’s (ORNL’s) Critical Experiments Facility (CEF) in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950s, efforts were made to study “power plants for the production of electrical power in space vehicles.”(a) The MPRE program was a part of those efforts and studied the feasibility of a stainless-steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967. The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of unmoderated stainless-steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were made to determine critical reflector arrangements, fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector.”(Reference 1) The experiment studied in this evaluation was the first of the series and had the fuel tubes packed tightly into a 22.87 cm outside diameter (OD) core tank. Two critical configurations were found by varying the amount of graphite reflector (References 1 and 2). Once the critical configurations had been achieved, various measurements of reactivity, relative axial and radial activation rates of 235U, , and cadmium ratios were performed. The cadmium ratio, reactivity, and activation rate measurements performed on the critical configurations are described in Sections 1.3, 1.4 and 1.7, respectively. Information for this

  4. Critical Configuration and Physics Measurements for Assemblies of U(93.15)O2 Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2012-09-01

    A series of critical experiments were completed in 1962-1965 at Oak Ridge National Laboratory’s (ORNL’s) Critical Experiments Facility (CEF) in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950s, efforts were made to study “power plants for the production of electrical power in space vehicles.”(a) The MPRE program was a part of those efforts and studied the feasibility of a stainless-steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967. The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of unmoderated stainless-steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were made to determine critical reflector arrangements, fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector.”(Reference 1) The experiment studied in this evaluation was the first of the series and had the fuel tubes packed tightly into a 22.87 cm outside diameter (OD) core tank. Two critical configurations were found by varying the amount of graphite reflector (References 1 and 2). Once the critical configurations had been achieved, various measurements of reactivity, relative axial and radial activation rates of 235U, , and cadmium ratios were performed. The cadmium ratio, reactivity, and activation rate measurements performed on the critical configurations are described in Sections 1.3, 1.4 and 1.7, respectively. Information for this

  5. Thermomechanical analysis of a fuel rod in a BWR reactor using the FUELSIM code; Analisis termomecanico de una barra de combustible de un reactor BWR utilizando el codigo FUELSIM

    Energy Technology Data Exchange (ETDEWEB)

    Pantoja C, R. [Escuela Superior de Fisica y Matematicas, Departamento de Ingenieria Nuclear, IPN, Av. Instituto Politecnico Nacional s/n, Col. San Pedro Zacatenco, 07738 Mexico, D. F. (Mexico); Ortiz V, J.; Araiza M, E. [ININ, Departamento de Sistemas Nucleares, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)], e-mail: rapaca78@yahoo.com.mx

    2009-10-15

    The thermomechanical behaviour of a fuel rod exposed to irradiation is a complex process in which are coupled great quantity of interrelated physical-chemical phenomena, for that analysis of rod performance in the core of a nuclear power reactor is realized generally with computation codes that integrate several phenomena expected during the time life of fuel rod in the core. An application of this type of thermomechanical codes is to predict, inside certain reliability margin, the design parameters that would be required to adjust, in order to get a better economy or rod performance, for a systematic approach to the fuel design optimization. FUELSIM is a thermomechanical code based on the models of FRAPCON code, which was developed under auspice of Nuclear Regulatory Commission of USA. FUELSIM allows iterative calculations like part of its programming structure, allowing search of extreme cases of behaviour, probabilistic analysis (or statistical), parametric analysis (or sensibility) and also can include as entrance data to the uncertainties associated with production data, code parameters and associated models. In this work is reported a first analysis of thermomechanical performance of a typical fuel rod used in a BWR 5/6. Results of maximum temperatures are presented in the fuel center and of axial deformation, for the 10 axial nodes in that the active longitude of fuel rod was divided. (Author)

  6. CONTROL ROD

    Science.gov (United States)

    Zinn, W.H.; Ross, H.V.

    1958-11-18

    A control rod is described for a nuclear reactor. In certaln reactor designs it becomes desirable to use a control rod having great width but relatively llttle thickness. This patent is addressed to such a need. The neutron absorbing material is inserted in a triangular tube, leaving volds between the circular insert and the corners of the triangular tube. The material is positioned within the tube by the use of dummy spacers to achleve the desired absorption pattern, then the ends of the tubes are sealed with suitable plugs. The tubes may be welded or soldered together to form two flat surfaces of any desired width, and covered with sheetmetal to protect the tubes from damage. This design provides a control member that will not distort under the action of outside forces or be ruptured by gases generated within the jacketed control member.

  7. Surface area considerations for corroding N reactor fuel

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, A.B. Jr.; Pitner, A.L.

    1996-06-01

    The N Reactor fuel is corroding at sites where the Zircaloy cladding was damaged when the fuel was discharged from the reactor. Corroding areas are clearly visible on the fuel stored in open cans in the K East Basin. There is a need to estimate the area of the corroding uranium to analyze aspects of fuel behavior as it is transitioned. from current wet storage to dry storage. In this report, the factors that contribute to {open_quotes}true{close_quotes} surface area are analyzed in terms of what is currently known about the N Reactor fuel. Using observations from a visual examinations of the fuel in the K East wet storage facility, a value for the corroding geometric area is estimated. Based on observations of corroding uranium and surface roughness values for other metals, a surface roughness factor is also estimated and applied to the corroding K East fuel to provide an estimated {open_quotes}true{close_quotes} surface area. While the estimated area may be modified as additional data become available from fuel characterization studies, the estimate provides a basis to assess effects of exposed uranium metal surfaces on fuel behavior in operations involved in transitioning from wet to dry storage, during shipment and staging, conditioning, and dry interim storage.

  8. Status of rod consolidation, 1988

    Energy Technology Data Exchange (ETDEWEB)

    Bailey, W.J.

    1989-01-01

    It is estimated that the spent fuel storage pools at some domestic light-water reactors will run out of space before 2003, the year that the US Department of Energy currently predicts it will have a repository available. Of the methods being studied to alleviate the problem, rod consolidation is one of the leading candidates for achieving more efficient use of existing space in spent fuel storage pools. Rod consolidation involves mechanically removing all the fuel rods from the fuel assembly hardware (i.e., the structural components) and placing the fuel rods in a close-packed array in a canister without space grids. A typical goal of rod consolidation systems is to insert the fuel rods from two fuel assemblies into a canister that has the same exterior dimensions as one standard fuel assembly (i.e., to achieve a consolidation or compaction ratio of 2:1) and to compact the nonfuel-bearing structural components from those two fuel assemblies by a factor of 10 to 20. This report provides an overview of the current status of rod consolidation in the United States and a small amount of information on related activities in other countries. 85 refs., 36 figs., 5 tabs.

  9. Determination of internal pressure and the backfill gas composition of nuclear fuel rods; Determinacion de la presion interna y la composicion del gas de llenado de barras de combustible nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Garcia C, M.A.; Cota S, G.; Merlo S, L.; Fernandez T, F. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1997-07-01

    An important consideration in the nuclear fuel manufacturing is the measurement of the helium atmosphere pressure and its composition analysis inside the nuclear fuel rod. In this work it is presented a system used to measure the internal pressure and to determine the backfill gas composition of fuel rods. The system is composed of an expansion chamber provided of a seals system to assure that when rod is drilled, the gas stays contained inside the expansion chamber. The system is connected to a pressure measurement digital system: Baratron MKS 310-AHS-1000. Range 1000 mm Hg from which the pressure readings are taken when this is stabilized in all the system. After a gas sample is sent toward a Perkin Elmer gas chromatograph, model 8410 with thermal conductivity detector to get the corresponding chromatogram and doing the necessary calculations for obtaining the backfill gas composition of the rod in matter. (Author)

  10. Yeast surface display of dehydrogenases in microbial fuel-cells.

    Science.gov (United States)

    Gal, Idan; Schlesinger, Orr; Amir, Liron; Alfonta, Lital

    2016-12-01

    Two dehydrogenases, cellobiose dehydrogenase from Corynascus thermophilus and pyranose dehydrogenase from Agaricus meleagris, were displayed for the first time on the surface of Saccharomyces cerevisiae using the yeast surface display system. Surface displayed dehydrogenases were used in a microbial fuel cell and generated high power outputs. Surface displayed cellobiose dehydrogenase has demonstrated a midpoint potential of -28mV (vs. Ag/AgCl) at pH=6.5 and was used in a mediator-less anode compartment of a microbial fuel cell producing a power output of 3.3μWcm(-2) using lactose as fuel. Surface-displayed pyranose dehydrogenase was used in a microbial fuel cell and generated high power outputs using different substrates, the highest power output that was achieved was 3.9μWcm(-2) using d-xylose. These results demonstrate that surface displayed cellobiose dehydrogenase and pyranose dehydrogenase may successfully be used in microbial bioelectrochemical systems.

  11. Heat flux and temperature determination on the control rod outer surface

    Energy Technology Data Exchange (ETDEWEB)

    Taler, J.; Cebula, A. [Cracow Univ. of Tech., Cracow (Poland); Marcinkiewicz, J.; Tinoco, H. [Forsmarks Kraftgrupp AB, Osthammar (Sweden)

    2011-07-01

    The paper presents heat transfer calculation results concerning a control rod of Unit 3 of Forsmark Nuclear Power Plant (NPP). The part of the control rod, which is the object of interest, is surrounded by a mixing region of hot and cold flows and, as a consequence, is subjected to thermal fluctuations. The paper describes a numerical test which validates the method based on the solution of the inverse heat conduction problem (IHCP). The comparison of the results achieved by two methods, CFD and IHCP, including a description of the IHCP method used in the calculation process, shows a very good agreement between the methods. (author)

  12. Verification of heat flux and temperature calculation on the control rod outer surface

    Science.gov (United States)

    Taler, Jan; Cebula, Artur

    2011-12-01

    The paper presents heat transfer calculation results concerning a control rod of Forsmark Nuclear Power Plant (NPP). The part of the control rod, which is the object of interest, is surrounded by a mixing region of hot and cold flows and, as a consequence, is subjected to thermal fluctuations. The paper describes a numerical test which validates the method based on the solution of the inverse heat conduction problem (IHCP). The comparison of the results achieved by two methods, computational fluid dynamics (CFD) simulations and IHCP, including a description of the IHCP method used in the calculation process, shows a very good agreement between the methods.

  13. 燃料棒径向温度场稳态计算分析%Calculation and Analysis of the Radial Temperature Field of the Fuel Rods

    Institute of Scientific and Technical Information of China (English)

    齐航; 周蓝宇; 张雍良; 曾文杰

    2016-01-01

    燃料棒是反应堆的核心部件,其内部温度场分布大都通过数值计算获得。以燃料棒为研究对象,以燃料棒中心为起点,在径向上划分足够多的环形区域,建立几何模型,依据几何模型建立堆芯稳态物理模型,通过编程进行数值计算来获得燃料元件的径向稳态温度场。以次临界堆MYRRHA的燃料棒为研究对象,研究结果表明该方法能较准确的表征燃料元件径向稳态温度场的情况,是一种简单有效的建模分析方法。可见,该模型可以为燃料元件径向稳态温度场计算提供合理的依据。%Fuel rods is the core component of the reactor, often, its inner temperature field distribution is obtained through numerical calculation method. Taking the fuel rod as the research object, the center of the fuel rod as the starting point, division enough annular region in the radial, and the geometric model is set up, according to the geometric model building reactor core steady-state physical model, apply numerical calculation and programming to obtain fuel element radial steady-state temperature field. Sub-critical reactor MYRRHA fuel element as the research object. The results show that the method can accurately characterize the radial temperature field of the cylindrical fuel element, and it is a simple and effective modeling and analysis method. It can be seen that the model can provide a reasonable basis for calculating the radial temperature field of the cylindrical fuel element.

  14. Study of heat transfer in a eccentric fuel rods in a non stop planned shutdown of a PWR type reactor; Estudo da transferencia de calor em uma vareta combustivel excentrica, num desligamento nao planejado de um reator do tipo PWR

    Energy Technology Data Exchange (ETDEWEB)

    Affonso, Renato Raoni Werneck; Lava, Deise Diana; Borges, Diogo da Silva; Sampaio, Paulo Augusto Berquo de; Moreira, Maria de Lourdes, E-mail: raoniwa@yahoo.com.br, E-mail: deisedy@gmail.com, E-mail: diogosb@outlook.com, E-mail: sampaio@ien.gov.br, E-mail: malu@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2014-07-01

    This paper aims to conduct a case study in which the fuel pellets are displaced related to the center coating. Therefore, it will be addressed, first, the verification of computer code, comparing the results obtained with analytical solutions. This check is important so that, at a time later, you can use the program to know the fuel rod behavior and coolant channel.

  15. PLUTON: Three-group neutronic code for burnup analysis of isotope generation and depletion in highly irradiated LWR fuel rods

    Energy Technology Data Exchange (ETDEWEB)

    Lemehov, Sergei E; Suzuki, Motoe [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-08-01

    PLUTON is a three-group neutronic code analyzing, as functions of time and burnup, the change of radial profiles, together with average values, of power density, burnup, concentration of trans-uranium elements, plutonium buildup, depletion of fissile elements, and fission product generation in water reactor fuel rod with standard UO{sub 2}, UO{sub 2}-Gd{sub 2}O{sub 3}, inhomogeneous MOX, and UO{sub 2}-ThO{sub 2}. The PLUTON code, which has been designed to be run on Windows PC, has adopted a theoretical shape function of neutron attenuation in pellet, which enables users to perform a very fast and accurate calculation easily. The present code includes the irradiation conditions of the Halden Reactor which gives verification data for the code. The total list of trans-uranium elements included in the calculations consists of {sub 92}U{sup 233-239}, {sub 93}Np{sup 237-239}, {sub 94}Pu{sup 238-243}, {sub 95}Am{sup 241-244} (including isomers), and {sub 96}Cm{sup 242-245}. Poisoning fission products are represented by {sub 54}Xe{sup 131,133,135}, {sub 48}Cd{sup 113}, {sub 62}Sm{sup 149,151,152}, {sub 64}Gd{sup 154-160}, {sub 63}Eu{sup 153,155}, {sub 36}Kr{sup 83,85}, {sub 42}Mo{sup 95}, {sub 43}Tc{sup 99}, {sub 45}Rh{sup 103}, {sub 47}Ag{sup 109}, {sub 53}I{sup 127,129,131}, {sub 55}Cs{sup 133}, {sub 57}La{sup 139}, {sub 59}Pr{sup 141}, {sub 60}Nd{sup 143-150}, {sub 61}Pm{sup 147}. Fission gases and volatiles included in the code are {sub 36}Kr{sup 83-86}, {sub 54}Xe{sup 129-136}, {sub 52}Te{sup 125-130}, {sub 53}I{sup 127-131}, {sub 55}Cs{sup 133-137}, and {sub 56}Ba{sup 135-140}. Verification has been performed up to 83 GWd/tU, and a satisfactory agreement has been obtained. (author)

  16. Analysis on Fuel Thermal Conductivity Model of the Computer Code for Performance Prediction of Fuel Rods%燃料元件性能分析程序中的燃料热导率模型分析

    Institute of Scientific and Technical Information of China (English)

    李海; 黄晨; 杜爱兵; 徐宝玉

    2014-01-01

    The thermal conductivity is one of the most important parameters in the computer code for performance prediction for fuel rods.Several fuel thermal conductivity models used in foreign computer code,including thermal conductivity models for MOX fuel and UO2 fuel were introduced in this paper. Thermal conductivities were calculated by using these models, and the results were compared and analyzed.Finally, the thermal conductivity model for the native computer code for performance prediction for fuel rods in fast reactor was recommended.%热导率是燃料元件性能分析程序最重要的参数之一,本文介绍了各国部分性能分析程序的燃料热导率模型,按照 MOX和 UO2燃料分类,给出了这些性能分析程序热导率模型的计算结果,并进行分析对比,给出了国产快堆性能分析程序的热导率推荐模型。

  17. Electrostatic Deformation of Liquid Surfaces by a Charged Rod and a Van De Graaff Generator

    Science.gov (United States)

    Slisko, Josip; García-Molina, Rafael; Abril, Isabel

    2014-01-01

    Authors of physics textbooks frequently use the deflection of a thin, vertically falling water jet by a charged balloon, comb, or rod as a visually appealing and conceptually relevant example of electrostatic attraction. Nevertheless, no attempts are made to explore whether these charged bodies could cause visible deformation of a horizontal water…

  18. 水堆燃料元件性能分析及程序FROBA开发%Analysis of Fuel Rod Behavior and Design of FROBA Code

    Institute of Scientific and Technical Information of China (English)

    杨震; 苏光辉; 田文喜; 秋穗正

    2012-01-01

    在详细分析芯块和包壳的辐照行为的基础上,开发了燃料元件性能分析程序FROBA,并对燃料元件的热工-机械-材料特性进行模拟分析,计算得到不同燃耗深度下燃料元件的温度、应变特性.通过与美国爱达荷国家实验室的软件计算结果进行对比,验证本工作开发程序的准确性.结果表明:在芯块和包壳接触前,芯块温度先上升,密实化消失后温度逐渐下降;接触后芯块温度会再次上升.%The temperature and strain profile of pellet and cladding were studied by developing a thermomechanic coupling code FROBA,which was based on analyzing fuel rod behavior theoretically during irradiation. Based on the analysis of results under different operating conditions, a numerical method for calculating fuel rod behavior was obtained, which could be used for the analysis of fuel component under operational conditions of nuclear reactors. The reliability of the code was also proved by comparing the results derived from Idaho National Laboratory software. The results show that the fuel temperature rises before irradiation. Once the densification is complete, the fuel temperature drops. After the gap closure occurs, the temperature gradually rises again.

  19. Understanding the Atomic-Level Chemistry and Structure of Oxide Deposits on Fuel Rods in Light Water Nuclear Reactors Using First Principles Methods

    Science.gov (United States)

    Rak, Zs.; O'Brien, C. J.; Brenner, D. W.; Andersson, D. A.; Stanek, C. R.

    2016-09-01

    The results of recent studies are discussed in which first principles calculations at the atomic level have been used to expand the thermodynamic database for science-based predictive modeling of the chemistry, composition and structure of unwanted oxides that deposit on the fuel rods in pressurized light water nuclear reactors. Issues discussed include the origin of the particles that make up deposits, the structure and properties of the deposits, and the forms by which boron uptake into the deposits can occur. These first principles approaches have implications for other research areas, such as hydrothermal synthesis and the stability and corrosion resistance of other materials under other extreme conditions.

  20. Control Rod Ejection Accident while Using 6- and 8-Tube IRT-4M Fuel Assemblies in WWR-SM Research Reactor Core

    Energy Technology Data Exchange (ETDEWEB)

    Baytelesov, S.; Kungurov, F.; Safarov, A.; Salikhbaev, U.

    2011-07-01

    The WWR-SM reactor at the Institute of Nuclear Physics of the Academy of Sciences (INP AS) in Uzbekistan was converted to 6-tube IRT-4M LEU (19.7%) fuel in 2009. Presently, INP intends to also use IRT-4M 8-tube FA, and a safety analysis for these 'mixed' (8-tube and 6-tube FA) cores is required by the regulatory authorities. This paper presents results of control rod ejection transient analysis for these mixed cores

  1. Using Polymer Electrolyte Membrane Fuel Cells in a Hybrid Surface Ship Propulsion Plant to Increase Fuel Efficiency

    Science.gov (United States)

    2010-06-01

    Using Polymer Electrolyte Membrane Fuel Cells in a Hybrid Surface Ship Propulsion Plant to Increase Fuel Efficiency by Douglas M. Kroll B.S...Electrolyte Membrane Fuel Cells in a Hybrid Surface Ship Propulsion Plant to Increase Fuel Efficiency 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM...298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 Using Polymer Electrolyte Membrane Fuel Cells in a Hybrid Surface Ship Propulsion Plant to Increase

  2. Steadiness of a “water bell” surface to a destruction at a flow around of the thin rods assembly

    Directory of Open Access Journals (Sweden)

    Slesareva Ekaterina

    2015-01-01

    Full Text Available The experimental research of hydrodynamic stability of a dome-shaped film liquid at a flow around a thin plate has been carried out. Experiments were carry out with a film in shape a «water bell». The film was formed by a leak-in jet of water width 10 mm on a hard disk with diameter 14.5 mm. The width of a plate ζ changed from 0.05 to 3.5 mm. The plate placed along or across relative to the vector of velocity of a liquid in a film. Experiments have shown, that stability of a film of liquid at a flow around the plate is defined by velocity of water and a thickness of a film δ in front of the rod. It is shown, that for the appointed value of Reynolds number Reδ probably continuous flow at a flow around the plate, if Weber number Weζ less than threshold value. The criterion of steadiness a film of the «water bell» by a surface destruction at a flow around the rod is determined on the transverse size of the rod relative to the vector of velocity of a liquid.

  3. Development for analysis system of rods enrichment of nuclear fuels; Desarrollo de un sistema de analisis de enriquecimiento de barras de combustible nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Rojas C, E.L

    1998-11-01

    Nuclear industry is strongly regulated all over the world and quality assurance is important in every nuclear installation or process related with it. Nuclear fuel manufacture is not the exception. ININ was committed to manufacture four nuclear fuel bundles for the CFE nucleo electric station at Laguna Verde, Veracruz, under General Electric specifications and fulfilling all the requirements of this industry. One of the quality control requisites in nuclear fuel manufacture deals with the enrichment of the pellets inside the fuel bundle rods. To achieve the quality demanded in this aspect, the system described in this work was developed. With this system, developed at ININ it is possible to detect enrichment spikes since 0.4 % in a column of pellets with a 95 % confidence interval and to identify enrichment differences greater than 0.2 % e between homogeneous segments, also with a 95 % confidence interval. ININ delivered the four nuclear fuel bundles to CFE and these were introduced in the core of the nuclear reactor of Unit 1 in the fifth cycle. Nowadays they are producing energy and have shown a correct mechanical performance and neutronic behavior. (Author)

  4. Study of heat transfer in 3D fuel rods of the EPRI-9R reactor modified; Estudo da transferencia de calor em varetas combustiveis 3D do reator EPRI-9R 3D modificado

    Energy Technology Data Exchange (ETDEWEB)

    Affonso, Renato Raoni Werneck; Lava, Deise Diana; Borges, Diogo da Silva; Sampaio, Paulo Augusto Berquo de; Moreira, Maria de Lourdes, E-mail: raoniwa@yahoo.com.br, E-mail: deisedy@gmail.com, E-mail: diogosb@outlook.com, E-mail: sampaio@ien.gov.br, E-mail: malu@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2014-07-01

    This paper aims to conduct a case study of the fuel rods that have the highest and the lowest average power of the EPRI-9R 3D reactor modified , for various positions of the control rods banks. For this, will be addressed the verification of computer code, comparing the results obtained with analytical solutions. This check is important so that, subsequently, it is possible use the program to understand the behavior of the fuel rods and the coolant channel of the EPRI-9R 3D reactor modified. Thus, in view of the scope of this paper, first a brief introducing on the heat transfer is done, including the rod equations and the equation of energy in the channel to allow the analysis of the results.

  5. Development of thermal protective seal for hot structure control surface actuator rod

    Science.gov (United States)

    Infed, F.; Handrick, K.; Lange, H.; Steinacher, A.; Weiland, S.; Wegmann, C.

    2012-01-01

    For the Intermediate eXperimental Vehicle (IXV) the deflection of the highly loaded body flap is performed by an actuator system which is connected to the body flap by a rod. Besides the thermal and mechanical loads the sealing of the inner vehicle against the possible leaking hot plasma is an important issue whereby the special challenge for the design results from the spatial movement of the rod. This requires a design consisting of different parts and various materials in order to satisfy the mechanical flexibility and the resistance to the thermal and mechanical loads under the aspect of reusability. This paper describes the MT Aerospace approach for the thermal protection system for the actuator as presented for the critical design review of IXV. The design is presented and described including all necessary performed analysis steps toward such a design.

  6. Composite nuclear fuel assembly

    Energy Technology Data Exchange (ETDEWEB)

    Dollard, W.J.; Ferrari, H.M.

    1982-04-27

    An open lattice elongated nuclear fuel assembly including small diameter fuel rods disposed in an array spaced a selected distance above an array of larger diameter fuel rods for use in a nuclear reactor having liquid coolant flowing in an upward direction. Plenums are preferably provided in the upper portion of the upper smaller diameter fuel rods and in the lower portion of the lower larger diameter fuel rods. Lattice grid structures provide lateral support for the fuel rods and preferably the lowest grid about the upper rods is directly and rigidly affixed to the highest grid about the lower rods.

  7. Calculation of the internal pressure of fuel rod from measurements of krypton-85 at its plenum; Calculo de la presion interna de barra combustible a partir de la medida de kripton-85 en su plenum

    Energy Technology Data Exchange (ETDEWEB)

    Arana, I.; Doncel, N.; Casado, C.

    2012-07-01

    ENUSA carried out numerous campaigns of measurement internal pressure of fuel rod irradiated. All of them have been performed of form destructively in a hot cell laboratory which implies a time high to obtain results and a high economic cost to obtain a single data by rod, representative of the end of the irradiation. The objective of the project is to develop a non-destructive measurement and a methodology for reliable calculation that eliminates these problems.

  8. Rod consolidation at the West Valley Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    Bailey, W.J.

    1986-12-01

    A rod consolidation demonstration with irradiated pressurized water reactor fuel was recently conducted by personnel from Nuclear Assurance Corporation and West Valley Nuclear Services Company at the West Valley Demonstration Project in West Valley, New York. The rod consolidation demonstration involved pulling all of the fuel rods from six fuel Assemblies. In general, the rod pulling proceeded smoothly. The highest compaction ratio attained was 1:8:1. Among the total of 1074 fuel rods were some known degraded rods (they had collapsed cladding, a result of in-reactor fuel densification), but no rods were broken or dropped during the demonstration. One aim was to gather information on the effect of rod consolidation operations on the integrity of the fuel rods during subsequent handling and storage. Another goal was to collect information on the condition and handling of intact, damaged, and failed fuel that has been in storage for an extended period. 9 refs., 8 figs., 1 tab.

  9. Evaluation of the thermal-mechanic performance of fuel rods MOX in fuel assemblies 10 x 10; Evaluacion del desempeno termo-mecanico barras combustibles MOX en ensambles combustible 10 x 10

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez L, H., E-mail: hector.hernandez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2012-10-15

    In the Instituto Nacional de Investigaciones Nucleares (Mexico) , we have been working in proposals of fuel assemblies that bear to the reduction of the plutonium inventories that exist a global level, plutonium coming from the dismantlement of the nuclear weapons as of the one used as fuel inside the reactors in operation at the present time. For this reason besides carrying out the evaluation of the neutron performance is necessary to realize the evaluation of the thermal-mechanic behavior of the rods that compose a fuel assembly with the purpose of determining if under the operation conditions to those that are subjected the fuel does not surpass the limit established and this causes a failure in the fuel element. In this sense when carrying out the analysis of an fuel element of mixed oxides in an arrangement 10 x 10 is observed that under the established operation conditions for the proposed cycle values that surpass the limit established for fuel failure are not presented, therefore the proposed assembly can be used as reload element in the nuclear power plant of Laguna Verde. (Author)

  10. Thermal hydraulics of rod bundles: The effect of eccentricity

    Energy Technology Data Exchange (ETDEWEB)

    Chauhan, Amit K., E-mail: amit_fmlab@yahoo.co.in [Fluid Mechanics Laboratory, Department of Applied Mechanics, Indian Institute of Technology Madras, Chennai 600036 (India); Prasad, B.V.S.S.S., E-mail: prasad@iitm.ac.in [Thermal Turbomachines Laboratory, Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai 600036 (India); Patnaik, B.S.V., E-mail: bsvp@iitm.ac.in [Fluid Mechanics Laboratory, Department of Applied Mechanics, Indian Institute of Technology Madras, Chennai 600036 (India)

    2013-10-15

    Highlights: • Present CFD investigation explores, whole bundle eccentricity for the first time. • Fluid flow and thermal characteristics in various subchannels are analyzed. • Mass flux distribution is particularly analyzed to study eccentricity effect. • Higher eccentricity resulted in a shoot up in rod surface temperature distribution. • Both tangential and radial flow in rod bundles has resulted due to eccentricity. -- Abstract: The effect of eccentricity on the fluid flow and heat transfer through a 19-rod bundle is numerically carried out. When the whole bundle shifts downwards with respect to the outer (pressure) tube, flow redistribution happens. This in turn is responsible for changes in mass flux, pressure and differential flow development in various subchannels. The heat flux imposed on the surface of the fuel rods and the mass flux through the subchannels determines the coolant outlet temperatures. The simulations are performed for a coolant flow Reynolds number of 4 × 10{sup 5}. For an eccentricity value of 0.7, the mass flux in the bottom most subchannel (l) was found to decrease by 10%, while the surface temperature of the fuel rod in the vicinity of this subchannel increased by 250% at the outlet section. Parameters of engineering interest including skin friction coefficient, Nusselt number, etc., have been systematically explored to study the effect of eccentricity on the rod bundle.

  11. MCTP, a code for the thermo-mechanical analysis of a fuel rod of BWR type reactors (Neutron part); MCTP, un codigo para el analisis termo-mecanico de una barra combustible de reactores tipo BWR (Parte Neutronica)

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez L, H.; Ortiz V, J. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: hhl@nuclear.inin.mx

    2003-07-01

    In the National Institute of Nuclear Research of Mexico a code for the thermo-mechanical analysis of the fuel rods of the BWR type reactors of the Nucleo electric Central of Laguna Verde is developed. The code solves the diffusion equation in cylindrical coordinates with several energy groups. The code, likewise, calculates the temperature distribution and power distribution in those fuel rods. The code is denominated Multi groups With Temperatures and Power (MCTP). In the code, the energy with which the fission neutrons are emitted it is divided in six groups. They are also considered the produced perturbations by the changes in the temperatures of the materials that constitute the fuel rods, the content of fission products, the uranium consumption and in its case the gadolinium, as well as the plutonium production. In this work there are present preliminary results obtained with the code, using data of operation of the Nucleo electric Central of Laguna Verde. (Author)

  12. Research on the mechanism of formation of deposits in the fuel rod; Investigacion sobre el mecanismo de formacion de depositos en la barra combustible

    Energy Technology Data Exchange (ETDEWEB)

    Doncel, N.

    2012-11-01

    Nowadays, the interrelation between the chemistry of the coolant and the behavior of the fuel in the reactor core is considered one of the key points in the management of the reactor. Phenomena as the Axial Offset Anomaly and its association with potential Boron precipitation mechanisms in the crud deposited on the fuel have shown the necessity of an improvement in the knowledge of these mechanisms. Following this reasoning Enusa, in close collaboration with the national nuclear industry, and later with EPRI, has developed a project to investigate the chemical reactions determining the basic precipitation mechanism/dissolution of Boron in the fuel cladding. With this purpose, a test program in an specifically installation has been carried out to represent thermal conditions (sub-cooling Boiling rate) and chemicals (pH, concentration of nickel) of PWR fuel rods, with the main objective of detecting the Boron and Lithium into the crud layers. The main results of this investigation, as well as their conclusion, have contributed significantly to the general understanding of these phenomena, and will be presented in the following paper. (Author) 10 refs.

  13. Influence of Flaws of Wire Rod Surface, Inclusions and Voids on Wire Breaks in Superfine Wire Drawing

    Science.gov (United States)

    Yoshida, Kazunari; Norasethasopon, Somchai; Shinohara, Tetsuo; Ido, Ryuta

    By means of the finite element analysis (FEA), this study analyzed wire breaks that occurred in the drawing fine wires containing flaws on the wire surface, inclusion and void. The deformation behavior of an inclusion was examined, in which the inclusion's location is assumed to be on the center axis of the wire, and the cause of wire breaks and their prevention method were clarified. It was found that an inclusion diameter/wire diameter ratio of 0.4 or higher increases the likelihood of wire breaks occurring. When the inclusion is not assumed to be in the center axis of the wire, it was also found that necking and wire breaks appear more frequently. FEA showed that a flaw grows with each processing step, when a small circumferential flaw is placed on the wire rod surface, and eventually becomes a surface defect, which is called a check mark in practice.

  14. Standard fire behavior fuel models: a comprehensive set for use with Rothermel's surface fire spread model

    Science.gov (United States)

    Joe H. Scott; Robert E. Burgan

    2005-01-01

    This report describes a new set of standard fire behavior fuel models for use with Rothermel's surface fire spread model and the relationship of the new set to the original set of 13 fire behavior fuel models. To assist with transition to using the new fuel models, a fuel model selection guide, fuel model crosswalk, and set of fuel model photos are provided.

  15. A contribution to the analysis of the thermal behaviour of Fast Breeder fuel rods with UO{sub 2}-PuO{sub 2} fuel; Contribucion al analisis del comportamiento termico de las barras combustibles de UO{sub 2}-PuO{sub 2} de los reactores rapidos

    Energy Technology Data Exchange (ETDEWEB)

    Lopez Jimenez, J.; Elbel, H.

    1977-07-01

    The fuel of Fast Breeder Reactors which consists of Uranium and Plutonium dioxide is mainly characterized by the amount and distribution of void volume and Plutonium and the amount of oxygen. Irradiation experiments carried out with this fuel have shown that initial structure of the fuel pellet is subjected to large changes during operation. These are consequences of the radial and axial temperature gradients within the fuel rods. (Author) 54 refs.

  16. Research of some marks contemporary hydrocarbon fuel surface tension

    Directory of Open Access Journals (Sweden)

    С.В. Бойченко

    2005-01-01

    Full Text Available  The  surface  tension  of  some  marks  domestic  and  foreign  gasoline’s  and  jet  fuels  is  investigated  depending  on  distillation. Dependences  of  surface  tension,  composition,  boiling  points  liquid  fuel  experimentally  are  received.

  17. Investigating hydrodynamic characteristics and peculiarities of the coolant flow behind a spacer grid of a fuel rod assembly of the floating nuclear power unit

    Science.gov (United States)

    Dmitriev, S. M.; Doronkov, D. V.; Legchanov, M. A.; Pronin, A. N.; Solncev, D. N.; Sorokin, V. D.; Hrobostov, A. E.

    2016-05-01

    The results of experimental investigations of local hydrodynamics of a coolant flow in fuel rod assembly (FA) of KLT-40C reactor behind a plate spacer grid have been presented. The investigations were carried out on an aerodynamic rig using the gas-phase diffusive tracer test. An analysis of spatial distribution of absolute flow velocity projections and distribution of tracer concentration allowed specifying a coolant flow pattern behind the plate spacer grid of the FA. On the basis of obtained experimental data the recommendations were provided to specify procedures for determining the coolant flow rates for the programs of cell-wise calculation of a core zone of KLT-40C reactor. Investigation results were accepted for the practical use in JSC "OKBM Afrikantov" to assess heat engineering reliability of cores of KLT-40C reactor and were included in a database for verification of CFD programs (CFD-codes).

  18. Preparation of carbon alloy catalysts for polymer electrolyte fuel cells from nitrogen-containing rigid-rod polymers

    Energy Technology Data Exchange (ETDEWEB)

    Chokai, Masayuki [Department of Organic and Polymeric Materials, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo 152-8552 (Japan); Integrative Technology Research Institute, Teijin Ltd., 4-3-2, Asahigaoka, Hino, Tokyo 191-8512 (Japan); Taniguchi, Masataka; Shinoda, Tsuyoshi; Nabae, Yuta; Kuroki, Shigeki; Hayakawa, Teruaki; Kakimoto, Masa-aki [Department of Organic and Polymeric Materials, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo 152-8552 (Japan); Moriya, Shogo; Matsubayashi, Katsuyuki [Department of Organic and Polymeric Materials, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo 152-8552 (Japan); Business Development Division, Nisshinbo Holdings, Inc., 1-2-3, Onodai, Midori-ku, Chiba 267-0056 (Japan); Ozaki, Jun-ichi [Department of Organic and Polymeric Materials, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo 152-8552 (Japan); Department of Nanomaterial Systems, Graduate School of Engineering, Gunma University, 1-5-1, Tenjin-cho, Kiryu, Gunma 376-8515 (Japan); Miyata, Seizo [Department of Organic and Polymeric Materials, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo 152-8552 (Japan); New Energy and Industrial Technology Development Organization, 1310 Omiya-cho, Saiwai-ku, Kawasaki, Kanagawa 212-8554 (Japan)

    2010-09-15

    Carbon alloy catalysts (CAC), non-precious metal catalysts for the oxygen reduction reaction (ORR), were prepared from various kinds of nitrogen-containing rigid-rod aromatic polymers, polyimides, polyamides and azoles, by carbonization at 900 C under nitrogen flow. The catalytic activity for ORR was evaluated by the onset potential, which was taken at a current density of -2 {mu}A cm{sup -2}. Carbonized polymers having high nitrogen content showed higher onset potential. In particular, CACs derived from azole (Az5) had an onset potential of 0.8 V, despite being was prepared without any metals. (author)

  19. Partially-reflected water-moderated square-piteched U(6.90)O2 fuel rod lattices with 0.67 fuel to water volume ratio (0.800 CM Pitch)

    Energy Technology Data Exchange (ETDEWEB)

    Harms, Gary A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    The US Department of Energy (DOE) Nuclear Energy Research Initiative funded the design and construction of the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratories. The start-up of the experiment facility and the execution of the experiments described here were funded by the DOE Nuclear Criticality Safety Program. The 7uPCX is designed to investigate critical systems with fuel for light water reactors in the enrichment range above 5% 235U. The 7uPCX assembly is a water-moderated and -reflected array of aluminum-clad square-pitched U(6.90%)O2 fuel rods.

  20. Micro reactor physics of MOX fueled LWR

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Toshikazu [Osaka Univ. (Japan)

    2001-09-01

    Upon the background that the LWR fuels become complicated in recent years because of the introduction of high burnup fuels, high density Gd fuels, MOX fuels, the author proposes the Micro Reactor Physics. He intends to investigate the behaviors of neutrons and reactions in a pin rod that have not yet been paid attention. Conventionally the resonance absorption has been evaluated by assuming the uniform effective cross sections in a pin rod. However, due to the self-shielding, the neutron spectrum near the surface of the rod is quite different with that of the center of rod. This fact affects the spatial distributions of Pu isotopes produced during burnup. The spatial distribution of temperature in a rod affects the Doppler coefficient. He solved this problem by the multi-band method. In the case where MOX rods are adjacent with U rods, the spectrum of the current from MOX rods to U rods is different with that of U to MOX. That makes the spatial distribution of azimuthal direction together with that of the infinite lattice. He solved this problem by a cell calculation based on the characteristic method. This report introduces several numerical results of his Micro Reactor Physics. One of the important results is the indication that the conventional Doppler coefficient gives 20% higher (not conservative) value. (K. Tsuchihashi)

  1. Micro reactor physics of MOX fueled LWR

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Toshikazu [Osaka Univ. (Japan)

    2001-09-01

    Upon the background that the LWR fuels become complicated in recent years because of the introduction of high burnup fuels, high density Gd fuels, MOX fuels, the author proposes the Micro Reactor Physics. He intends to investigate the behaviors of neutrons and reactions in a pin rod that have not yet been paid attention. Conventionally the resonance absorption has been evaluated by assuming the uniform effective cross sections in a pin rod. However, due to the self-shielding, the neutron spectrum near the surface of the rod is quite different with that of the center of rod. This fact affects the spatial distributions of Pu isotopes produced during burnup. The spatial distribution of temperature in a rod affects the Doppler coefficient. He solved this problem by the multi-band method. In the case where MOX rods are adjacent with U rods, the spectrum of the current from MOX rods to U rods is different with that of U to MOX. That makes the spatial distribution of azimuthal direction together with that of the infinite lattice. He solved this problem by a cell calculation based on the characteristic method. This report introduces several numerical results of his Micro Reactor Physics. One of the important results is the indication that the conventional Doppler coefficient gives 20% higher (not conservative) value. (K. Tsuchihashi)

  2. Operational modal analysis of flow-induced vibration of nuclear fuel rods in a turbulent axial flow

    Energy Technology Data Exchange (ETDEWEB)

    De Pauw, B., E-mail: bdepauw@vub.ac.be [Vrije Universiteit Brussel (VUB), Brussels Photonics Team (B-Phot), Brussels (Belgium); Vrije Universiteit Brussel (VUB), Department of Mechanical Engineering (AVRG), Brussels (Belgium); Belgian Nuclear Research Centre (SCK-CEN), Boeretang 200, Mol (Belgium); Weijtjens, W.; Vanlanduit, S. [Vrije Universiteit Brussel (VUB), Department of Mechanical Engineering (AVRG), Brussels (Belgium); Van Tichelen, K. [Belgian Nuclear Research Centre (SCK-CEN), Boeretang 200, Mol (Belgium); Berghmans, F. [Vrije Universiteit Brussel (VUB), Brussels Photonics Team (B-Phot), Brussels (Belgium)

    2015-04-01

    Highlights: • We describe an analysis technique to evaluate nuclear fuel pins. • We test a single fuel pin mockup subjected to turbulent axial flow. • Our analysis is based on operational modal analysis (OMA). • The accuracy and precision of our method is higher compared to traditional methods. • We demonstrate the possible onset of a fluid-elastic instability. - Abstract: Flow-induced vibration of nuclear reactor fuel pins can result in mechanical noise and lead to failure of the reactor's fuel assembly. This problem can be exacerbated in the new generation of liquid heavy metal fast reactors that use a much denser and more viscous coolant in the reactor core. An investigation of the flow-induced vibration in these particular conditions is therefore essential. In this paper, we describe an analysis technique to evaluate flow-induced vibration of nuclear reactor fuel pins subjected to a turbulent axial flow of heavy metal. We deal with a single fuel pin mockup designed for the lead–bismuth eutectic (LBE) cooled MYRRHA reactor which is subjected to similar flow conditions as in the reactor core. Our analysis is based on operational modal analysis (OMA) techniques. We show that the accuracy and precision of our OMA technique is higher compared to traditional methods and that it allows evaluating the evolution of modal parameters in operational conditions. We also demonstrate the possible onset of a fluid-elastic instability by tracking the modal parameters with increasing flow velocity.

  3. Direct Measurement of U235 and Pu239 in Spent Fuel Rods with Gamma-Ray Mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Ziock, Klaus-Peter [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Alameda, J. B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brejnholt, N. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Decker, T. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Descalle, M. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fernandez-Perea, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hill, R. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kisner, R. A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Melin, A. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Patton, B. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ruz, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Soufli, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2013-09-30

    The amounts of fissile Pu and U in spent nuclear fuel are of primary concern to the safeguards community. In particular, there are issues when safeguards transitions from an item accountancy basis (such as fuel bundles) to a fissile material mass basis as occurs when spent fuel enters a reprocessing plant. Discrepancies occur because item accountancy requires estimating the content of fissile material using indirect techniques such as the fuel burn-up and item-level measurements of radiation emissions from fission by-products. Direct measurement of the fissile content by monitoring line emissions from fissile species themselves is impossible because the lines are much weaker than those emitted by shorter-lived isotopes in the fuel. The goal of this project is to develop a technique to directly measure these weaker lines despite the presence of overwhelming radiation from other isotopes. This is achieved by using gamma-ray mirrors as a narrow band-pass filter. The mirrors reflect only energies of interest toward a HPGe detector that is shielded from direct view of the spent fuel and its fierce emissions. This can significantly improve the reliability with which the mass of fissile material is tracked.

  4. Evaluation of the fuel rod integrity in PWR reactors from the spectrometric analysis of the primary coolant; Avaliacao da integridade de varetas combustiveis em reatores PWR a partir da analise espectrometrica da agua do primario

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Iara Arraes

    1999-02-15

    The main objective of this thesis is to provide a better comprehension of the phenomena involved in the transport of fission products, from the fuel rod to the coolant of a PWR reactor. To achieve this purpose, several steps were followed. Firstly, it was presented a description of the fuel elements and the main mechanisms of fuel rod failure, indicating the most important nuclides and their transport mechanisms. Secondly, taking both the kinetic and diffusion models for the transport of fission products as a basis, a simple analytical and semi-empirical model was developed. This model was also based on theoretical considerations and measurements of coolant's activity, according to internationally adopted methodologies. Several factors are considered in the modelling procedures: intrinsic factors to the reactor itself, factors which depend on the reactor's operational mode, isotope characteristic factors, and factors which depend on the type of rod failure. The model was applied for different reactor's operational parameters in the presence of failed rods. The main conclusions drawn from the analysis of the model's output are relative to the variation on the coolant's water activity with the fuel burnup, the linear operation power and the primary purification rate and to the different behaviour of iodine and noble gases. The model was saturated from a certain failure size and showed to be unable to distinguish between a single big fail and many small ones. (author)

  5. Experimental Research on Water Boiling Heat Transfer on Horizontal Copper Rod Surface at Sub-Atmospheric Pressure

    Directory of Open Access Journals (Sweden)

    Li-Hua Yu

    2015-09-01

    Full Text Available In recent years, water (R718 as a kind of natural refrigerant—which is environmentally-friendly, safe and cheap—has been reconsidered by scholars. The systems of using water as the refrigerant, such as water vapor compression refrigeration and heat pump systems run at sub-atmospheric pressure. So, the research on water boiling heat transfer at sub-atmospheric pressure has been an important issue. There are many research papers on the evaporation of water, but there is a lack of data on the characteristics at sub-atmospheric pressures, especially lower than 3 kPa (the saturation temperature is 24 °C. In this paper, the experimental research on water boiling heat transfer on a horizontal copper rod surface at 1.8–3.3 kPa is presented. Regression equations of the boiling heat transfer coefficient are obtained based on the experimental data, which are convenient for practical application.

  6. Evaluation of the thermal-mechanical performance of fuel rods of a BWR during a power ramp using the FUELSIM code; Evaluacion del desempeno termomecanico de barras de combustible de un reactor BWR durante una rampa de potencia utilizando el codigo FUELSIM

    Energy Technology Data Exchange (ETDEWEB)

    Pantoja C, R.

    2010-07-01

    To avoid the risk to environment due to release of radioactive material, because of occurrence of an accident, it is the priority of the design and performance of the diverse systems of safety of a commercial nuclear power plant. The safety of nuclear power plants requires, therefore, monitoring those parameters having some direct or indirect effect on safety. The thermal limits are values set for those parameters considered having most impact on the safe operation of a nuclear power reactor. Some thermal limits monitoring requires the thermal-mechanical analysis of the rods containing the nuclear fuel. The fuel rod thermal-mechanical behavior under irradiation is a complex process in which there exists a great deal of interrelated physical and chemical phenomena, so that the fuel rod performance analysis in the core of a nuclear power reactor is generally accomplished by using computer codes, which integrate several of the phenomena that are expected to occur during the lifetime of the fuel rod in the core. The main application of the thermal-mechanical analysis codes is the prediction of occurrence of conditions and/or phenomena that could lead to the deterioration or even mechanical failure of the fuel rod cladding, as, for example, the pellet-cladding interaction. In the operation of a nuclear power reactor, fuel preconditioning operations refer to the operational procedures employed to reduce the fuel rod failure probability due to fuel-cladding interaction, specially during reactor startup. Preconditioning simulations are therefore necessary to determine in advance limit values for the power that can be generated in a fuel rod, and thus avoiding any rod damage. In this work, a first analysis of the thermal-mechanical performance of typical fuel rods used in nuclear reactors of the type BWR 5/6, as those two nuclear reactors in Laguna Verde, Veracruz, is performed. This study includes two types of fuel rods: one from a fuel assembly design with an array 8 x 8

  7. Modelling the cracking of pressurised water reactor fuel pellets and its consequences on the mechanical behaviour of the fuel rod; Etude de l'impact de la fissuration des combustibles nucleaires oxyde sur le comportement normal et incidentel des crayons combustible

    Energy Technology Data Exchange (ETDEWEB)

    Helfer, Th

    2006-03-15

    This thesis aims to model the cracking of pressurised water reactor fuel pellets and its consequences on the mechanical behaviour of the fuel rod. Fuel cracking has two main consequences. It relieves the stress in the pellet, upon which the majority of the mechanical and physico-chemical phenomena are dependent. It also leads to pellet fragmentation. Taking fuel cracking into account is therefore necessary to adequately predict the mechanical loading of the cladding during the course of an irradiation. The local approach to fracture was chosen to describe fuel pellet cracking. Practical considerations brought us to favour a quasi-static description of fuel cracking by means of a local damage models. These models describe the appearance of cracks by a local loss of rigidity of the material. Such a description leads to numerical difficulties, such as mesh dependency of the results and abrupt changes in the equilibrium state of the mechanical structure during unstable crack propagations. A particular attention was paid to these difficulties because they condition the use of such models in engineering studies. This work was performed within the framework of the ALCYONE fuel performance package developed at CEA/DEC/SESC which relies on the PLEIADES software platform. ALCYONE provides users with various approaches for modelling nuclear fuel behaviour, which differ in terms of the type geometry considered for the fuel rod. A specific model was developed and implemented to describe fuel cracking for each of these approaches. The 2D axisymmetric fuel rod model is the most innovative and was particularly studied. We show that it is able to assess, thanks to an appropriate description of fuel cracking, the main geometrical changes of the fuel rod occurring under normal and off-normal operating conditions. (author)

  8. Development and verification of NRC`s single-rod fuel performance codes FRAPCON-3 AND FRAPTRAN

    Energy Technology Data Exchange (ETDEWEB)

    Beyer, C.E.; Cunningham, M.E.; Lanning, D.D. [Pacific Northwest National Lab., Richland, WA (United States)

    1998-03-01

    The FRAPCON and FRAP-T code series, developed in the 1970s and early 1980s, are used by the US Nuclear Regulatory Commission (NRC) to predict fuel performance during steady-state and transient power conditions, respectively. Both code series are now being updated by Pacific Northwest National Laboratory to improve their predictive capabilities at high burnup levels. The newest versions of the codes are called FRAPCON-3 and FRAPTRAN. The updates to fuel property and behavior models are focusing on providing best estimate predictions under steady-state and fast transient power conditions up to extended fuel burnups (> 55 GWd/MTU). Both codes will be assessed against a data base independent of the data base used for code benchmarking and an estimate of code predictive uncertainties will be made based on comparisons to the benchmark and independent data bases.

  9. Monopolar fuel cell stack coupled together without use of top or bottom cover plates or tie rods

    Science.gov (United States)

    Narayanan, Sekharipuram R. (Inventor); Valdez, Thomas I. (Inventor)

    2009-01-01

    A monopolar fuel cell stack comprises a plurality of sealed unit cells coupled together. Each unit cell comprises two outer cathodes adjacent to corresponding membrane electrode assemblies and a center anode plate. An inlet and outlet manifold are coupled to the anode plate and communicate with a channel therein. Fuel flows from the inlet manifold through the channel in contact with the anode plate and flows out through the outlet manifold. The inlet and outlet manifolds are arranged to couple to the inlet and outlet manifolds respectively of an adjacent one of the plurality of unit cells to permit fuel flow in common into all of the inlet manifolds of the plurality of the unit cells when coupled together in a stack and out of all of the outlet manifolds of the plurality of unit cells when coupled together in a stack.

  10. Simulation of Thermopower Influence on Fuel Core of Power Rod in Nuclear Power Plant (NPP Active Zone

    Directory of Open Access Journals (Sweden)

    I. S. Kulikov

    2010-01-01

    Full Text Available The paper considers problems of modern methods for  calculation of designs and materials of nuclear power. A model of numerical analysis for stress-strain state of fuel pins in the NPP active zone is proposed in the paper. The paper contains simulation concerning a fuel core section of a nuclear reactor heat-generating element with subsequent solution of a temperature and thermoelastic problem in computer program complex FEA ANSYS Workbench 11.0. All the obtained results have passed through checking procedure.

  11. Direct measurement of 235U in spent fuel rods with Gamma-ray mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Ruz, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brejnholt, N. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Alameda, J. B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Decker, T. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Descalle, M. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fernandez-Perea, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hill, R. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kisner, R. A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Melin, A. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Patton, B. W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Soufli, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ziock, K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pivovaroff, M. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-12-22

    We report here that direct measurement of plutonium and uranium X-rays and gamma-rays is a highly desirable nondestructive analysis method for the use in reprocessing fuel environments. The high background and intense radiation from spent fuel make direct measurements difficult to implement since the relatively low activity of uranium and plutonium is masked by the high activity from fission products. To overcome this problem, we make use of a grazing incidence optic to selectively reflect Kα and Kβ fluorescence of Special Nuclear Materials (SNM) into a high-purity position-sensitive germanium detector and obtain their relative ratios.

  12. SPE (tm) regenerative hydrogen/oxygen fuel cells for extraterrestrial surface and microgravity applications

    Science.gov (United States)

    Mcelroy, J. F.

    1990-01-01

    Viewgraphs on SPE regenerative hydrogen/oxygen fuel cells for extraterrestrial surface and microgravity applications are presented. Topics covered include: hydrogen-oxygen regenerative fuel cell energy storage system; electrochemical cell reactions; SPE cell voltage stability; passive water removal SPE fuel cell; fuel cell performance; SPE water electrolyzers; hydrophobic oxygen phase separator; hydrophilic/electrochemical hydrogen phase separator; and unitized regenerative fuel cell.

  13. Coolant mixing in LMFBR rod bundles and outlet plenum mixing transients. Progress report, September 1, 1980-November 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Todreas, N.E.; Golay, M.W.; Wolf, L.

    1981-02-01

    Four tasks are reported: bundle geometry (wrapped and bare rods), subchannel geometry (bare rods), subchannel geometry (bare rods), LMFBR outlet plenum flow mixing, and theoretical determination of local temperature fields in LMFBR fuel rod bundles. (DLC)

  14. Surface modified stainless steels for PEM fuel cell bipolar plates

    Science.gov (United States)

    Brady, Michael P [Oak Ridge, TN; Wang, Heli [Littleton, CO; Turner, John A [Littleton, CO

    2007-07-24

    A nitridation treated stainless steel article (such as a bipolar plate for a proton exchange membrane fuel cell) having lower interfacial contact electrical resistance and better corrosion resistance than an untreated stainless steel article is disclosed. The treated stainless steel article has a surface layer including nitrogen-modified chromium-base oxide and precipitates of chromium nitride formed during nitridation wherein oxygen is present in the surface layer at a greater concentration than nitrogen. The surface layer may further include precipitates of titanium nitride and/or aluminum oxide. The surface layer in the treated article is chemically heterogeneous surface rather than a uniform or semi-uniform surface layer exclusively rich in chromium, titanium or aluminum. The precipitates of titanium nitride and/or aluminum oxide are formed by the nitriding treatment wherein titanium and/or aluminum in the stainless steel are segregated to the surface layer in forms that exhibit a low contact resistance and good corrosion resistance.

  15. The relationship of post-fire white ash cover to surface fuel consumption

    Science.gov (United States)

    Andrew T. Hudak; Roger D. Ottmar; Robert E. Vihnanek; Nolan W. Brewer; Alistair M. S. Smith; Penelope Morgan

    2013-01-01

    White ash results from the complete combustion of surface fuels, making it a logically simple retrospective indicator of surface fuel consumption. However, the strength of this relationship has been neither tested nor adequately demonstrated with field measurements. We measured surface fuel loads and cover fractions of white ash and four other surface materials (green...

  16. Surface science studies of model fuel cell electrocatalysts

    Energy Technology Data Exchange (ETDEWEB)

    Markovic, N.M.; Ross, P.N. [Lawrence Berkeley National Laboratory, Materials Sciences Division, University of California, 94720 Berkeley, CA (United States)

    2002-04-01

    The purpose of this review is to discuss progress in the understanding of electrocatalytic reactions through the study of model systems with surface spectroscopies. Pure metal single crystals and well-characterized bulk alloys have been used quite successfully as models for real (commercial) electrocatalysts. Given the sheer volume of all work in electrocatalysis that is on fuel cell reactions, we will focus on electrocatalysts for fuel cells. Since Pt is the model fuel cell electrocatalyst, we will focus entirely on studies of pure Pt and Pt bimetallic alloys. The electrode reactions discussed include hydrogen oxidation/evolution, oxygen reduction, and the electrooxidation of carbon monoxide, formic acid, and methanol. Surface spectroscopies emphasized are FTIR, STM/AFM and surface X-ray scattering (SXS). The discussion focuses on the relation between the energetics of adsorption of intermediates and the reaction pathway and kinetics, and how the energetics and kinetics relate to the extrinsic properties of the model system, e.g. surface structure and/or composition. Finally, we conclude by discussing the limitations that are reached by using pure metal single crystals and well-characterized bulk alloys as models for real catalysts, and suggest some directions for developing more realistic systems.

  17. Surface science studies of model fuel cell electrocatalysts

    Science.gov (United States)

    Marković, N. M.; Ross, P. N.

    2002-04-01

    The purpose of this review is to discuss progress in the understanding of electrocatalytic reactions through the study of model systems with surface spectroscopies. Pure metal single crystals and well-characterized bulk alloys have been used quite successfully as models for real (commercial) electrocatalysts. Given the sheer volume of all work in electrocatalysis that is on fuel cell reactions, we will focus on electrocatalysts for fuel cells. Since Pt is the model fuel cell electrocatalyst, we will focus entirely on studies of pure Pt and Pt bimetallic alloys. The electrode reactions discussed include hydrogen oxidation/evolution, oxygen reduction, and the electrooxidation of carbon monoxide, formic acid, and methanol. Surface spectroscopies emphasized are FTIR, STM/AFM and surface X-ray scattering (SXS). The discussion focuses on the relation between the energetics of adsorption of intermediates and the reaction pathway and kinetics, and how the energetics and kinetics relate to the extrinsic properties of the model system, e.g. surface structure and/or composition. Finally, we conclude by discussing the limitations that are reached by using pure metal single crystals and well-characterized bulk alloys as models for real catalysts, and suggest some directions for developing more realistic systems.

  18. Irradiation effects on thermal properties of LWR hydride fuel

    Science.gov (United States)

    Terrani, Kurt; Balooch, Mehdi; Carpenter, David; Kohse, Gordon; Keiser, Dennis; Meyer, Mitchell; Olander, Donald

    2017-04-01

    Three hydride mini-fuel rods were fabricated and irradiated at the MIT nuclear reactor with a maximum burnup of 0.31% FIMA or ∼5 MWd/kgU equivalent oxide fuel burnup. Fuel rods consisted of uranium-zirconium hydride (U (30 wt%)ZrH1.6) pellets clad inside a LWR Zircaloy-2 tubing. The gap between the fuel and the cladding was filled with lead-bismuth eutectic alloy to eliminate the gas gap and the large temperature drop across it. Each mini-fuel rod was instrumented with two thermocouples with tips that are axially located halfway through the fuel centerline and cladding surface. In-pile temperature measurements enabled calculation of thermal conductivity in this fuel as a function of temperature and burnup. In-pile thermal conductivity at the beginning of test agreed well with out-of-pile measurements on unirradiated fuel and decreased rapidly with burnup.

  19. Morphological analysis of zirconium nuclear fuel retaining rods braided with SiC: Quality assurance and defect identification

    Science.gov (United States)

    Glazoff, Michael V.; Hiromoto, Robert; Tokuhiro, Akira

    2014-08-01

    In the after-Fukushima world, the stability of materials under extreme conditions is an important issue for the safety of nuclear reactors. Among the methods explored currently to improve zircaloys’ thermal stability in off-normal conditions, using a protective coat of the SiC filaments is considered because silicon carbide is well known for its remarkable chemical inertness at high temperatures. A typical SiC fiber contains ∼50,000 individual filaments of 5-10 μm in diameter. In this paper, an effort was made to develop and apply mathematical morphology to the process of automatic defect identification in Zircaloy-4 rods braided with the protective layer of the silicon carbide filament. However, the issues of the braiding quality have to be addressed to ensure its full protective potential. We present the original mathematical morphology algorithms that allow solving this problem of quality assurance successfully. In nuclear industry, such algorithms are used for the first time, and could be easily generalized to the case of automated continuous monitoring for defect identification in the future.

  20. The Characteristics of Columniform Surface Wave Plasma Excited Around a Quartz Rod by 2.45 GHz Microwaves

    Science.gov (United States)

    Wu, Zhonghang; Liang, Rongqing; Nagatsu, Masaaki; Chang, Xijiang

    2016-10-01

    A novel surface wave plasma (SWP) source excited with cylindrical Teflon waveguide has been developed in our previous work. The plasma characteristics have been simply studied. In this work, our experimental device has been significantly improved by replacing the Teflon waveguide with a quartz rod, and then better microwave coupling and higher gas purity can be obtained during plasma discharge. The plasma spatial distributions, both in radial and axial directions, have been measured and the effect of gas pressure has been investigated. Plasma density profiles indicate that this plasma source can produce uniform plasma in an axial direction at low pressure, which shows its potential in plasma processing on a curved surface such as an inner tube wall. A simplified circular waveguide model has been used to explain the principle of plasma excitation. The distinguishing features and potential application of this kind of plasma source with a hardware improvement have been shown. supported in part by National Natural Science of Foundation of China (Nos. 11005021, 51177017 and 11175049), the Grants-in-Aid for Scientific Research of Japan Society for the Promotion of Science (No. 21110010) and the Fudan University Excellent Doctoral Research Program (985 project) and the Ph.D Programs Foundation of Ministry of Education of China (No. 20120071110031)

  1. Characterization and simulation of soft gamma-ray mirrors for their use with spent fuel rods at reprocessing facilities.

    Science.gov (United States)

    Ruz, J; Descalle, M A; Alameda, J B; Brejnholt, N F; Chichester, D L; Decker, T A; Fernandez-Perea, M; Hill, R M; Kisner, R A; Melin, A M; Patton, B W; Soufli, R; Trellue, H; Watson, S M; Ziock, K P; Pivovaroff, M J

    2016-06-01

    The use of a grazing incidence optic to selectively reflect K-shell fluorescence emission and isotope-specific lines from special nuclear materials is a highly desirable nondestructive analysis method for use in reprocessing fuel environments. Preliminary measurements have been performed, and a simulation suite has been developed to give insight into the design of the x ray optics system as a function of the source emission, multilayer coating characteristics, and general experimental configurations. The experimental results are compared to the predictions from our simulation toolkit to illustrate the ray-tracing capability and explore the effect of modified optics in future measurement campaigns.

  2. Nematic liquid crystals on spherical surfaces: Control of defect configurations by temperature, density, and rod shape

    Science.gov (United States)

    Dhakal, Subas; Solis, Francisco J.; Olvera de la Cruz, Monica

    2012-07-01

    Recent experiments have shown that defect conformations in spherical nematic liquid crystals can be controlled through variations of temperature, shell thickness, and other environmental parameters. These modifications can be understood as a result of the induced changes in the effective elastic constants of the system. To characterize the relation between defect conformations and elastic anisotropy, we carry out Monte Carlo simulations of a nematic on a spherical surface. As the anisotropy is increased, the defects flow from a tetrahedral arrangement to two coalescing pairs and then to a great circle configuration. We also analyze this flow using a variational method based on harmonic configurations.

  3. Bovine serum albumin surface imprinted polymer fabricated by surface grafting copolymerization on zinc oxide rods and its application for protein recognition.

    Science.gov (United States)

    Li, Xiangjie; Zhou, Jingjing; Tian, Lei; Li, Wei; Zhang, Baoliang; Zhang, Hepeng; Zhang, Qiuyu

    2015-10-01

    A novel bovine serum albumin (BSA) surface imprinted polymer based on ZnO rods was synthesized by surface grafting copolymerization. It exhibited an excellent recognition performance to bovine serum albumin. The adsorption capacity and imprinting factor of bovine serum albumin could reach 89.27 mg/g and 2.35, respectively. Furthermore, the fluorescence property of ZnO was used for tracing the process of protein imprinting and it implied the excellent optical sensing property of this material. More importantly, the hypothesis that the surface charge of carrier could affect the imprinting process was confirmed. That is, ZnO with positive surface charge could not only improve the recognition specificity of binding sites to template proteins (pI 7). It was also important that the reusability of ZnO@BSA molecularly imprinted polymers was satisfactory. This implied that the poor mechanical/chemical stability of traditional zinc oxide sensors could be solved by the introduction of surface grafting copolymerization. These results revealed that the ZnO@BSA molecularly imprinted polymers are a promising optical/electrochemical sensor element.

  4. Alternative Practices to Improve Surface Fleet Fuel Efficiency

    Science.gov (United States)

    2014-09-01

    practices that, if changed, could provide significant fuel savings for fossil fuel ships. Recent and potential future budget cuts give fuel conservation...changed, could provide significant fuel savings for fossil fuel ships. Recent and potential future budget cuts give fuel conservation and efficiency...Figure 1. Navy fossil fuel expenditure for FY 2013 (after Dhoran 2014). .......................1 Figure 2. Fuel curves for a DDG showing GPH burned as

  5. 棒束燃料组件特征栅元CFD方法研究%CFD Method Research on Characteristic Cells in Rod Bundle Fuel Assembly

    Institute of Scientific and Technical Information of China (English)

    陈杰; 陈炳德; 张虹

    2011-01-01

    Two characteristic cells are in AFA-3G fuel assembly, that is typical cell and control rod guide cell. And there are some rules on the arrangement of mixing vanes. For the two characteristic cells, mixing capability is evaluated axially from the point of the first and second kind of sub-channel with CFD method.Mass mixing and heat mixing are interaction but different with each other. Although the mass mixing in the first kind of sub-channel is stronger, the thermal capability of the two is to some tune from the point of heat transfer. In the experiment research on thermal-hydraulic performance of AFA-3G fuel assembly, the arrangements of mixing vanes should refer to the two spacer grids of characteristic cells.%AFA-3G燃料组件中存在典型栅元和控制棒导向管栅元两种特征栅元,定位格架搅混翼的排列也具有一定的规律性.本文采用计算流体力学(CFD)方法,分别针对两种特征栅元,从第一类子通道和第二类子通道的角度,沿程评价其交混性能.质量交混与热交混紧密联系又相互区别,第一类子通道质量交换较强,但从传热角度,二者性能相当.AFA-3G燃料组件热工水力性能的实验研究中,格架搅混翼的排列方式应分别参照两种特征栅元格架.

  6. Critical Configuration and Physics Measurements for Assemblies of U(93.15)O2 Fuel Rods (1.506-cm Pitch)

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2013-03-01

    A series of critical experiments were completed from 1962–1965 at Oak Ridge National Laboratory’s (ORNL’s) Critical Experiments Facility (CEF) in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950s, efforts were made to study “power plants for the production of electrical power in space vehicles.”(a) The MPRE program was a part of those efforts and studied the feasibility of a stainless-steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967.a The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of unmoderated stainless-steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were performed to determine critical reflector arrangements, relative fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector” (see Reference 1). The experiment studied in this evaluation was the second of the series and had the fuel rods in a 1.506-cm-triangular pitch. One critical configuration was found (see Reference 3). Once the critical configuration had been achieved, various measurements of reactivity, relative axial and radial activation rates of 235U,bc and cadmium ratios were performed. The cadmium ratio, reactivity, and activation rate measurements performed on the critical configuration are described in Sections 1.3, 1.4, and 1.7, respectively.

  7. LMFBR fuel assembly design for HCDA fuel dispersal

    Science.gov (United States)

    Lacko, Robert E.; Tilbrook, Roger W.

    1984-01-01

    A fuel assembly for a liquid metal fast breeder reactor having an upper axial blanket region disposed in a plurality of zones within the fuel assembly. The characterization of a zone is dependent on the height of the axial blanket region with respect to the active fuel region. The net effect of having a plurality of zones is to establish a dispersal flow path for the molten materials resulting during a core meltdown accident. Upward flowing molten material can escape from the core region and/or fuel assembly without solidifying on the surface of fuel rods due to the heat sink represented by blanket region pellets.

  8. Experimental data report for test TS-2; Reactivity initiated accident test in NSRR with pre-irradiated BWR fuel rod

    OpenAIRE

    1993-01-01

    本報告書は、1990年2月に実施した照射済BWR燃料を用いた2回目の反応度事故模擬実験であるTS-2について実験データをまとめたものである。TS-2実験に使用した試験燃料は初期濃縮度2.79%であり、敦賀1号炉で照射されたBWR7times7型燃料棒を短尺化したものである。短尺化に供した実用燃料のバンドル平均燃焼度は21.3Gwd/tであった。NSRRにおける照射実験は、大気圧、室温の静止水冷却条件下で行い、発熱量は72pm5cal/g・fuel(ピークエンタルピ66pm5cal/g・fuel)を与えた。その結果燃料破損は生じなかった。実験条件、実験方法、パルス照射時の燃料の過渡挙動及び照射後検査の結果をまとめて示した。...

  9. Experimental data report for test TS-1; Reactivity initiated accident test in NSRR with pre-irradiated BWR fuel rod

    OpenAIRE

    1992-01-01

    本報告書は、1989年10月に実施した照射済BWR燃料を用いた最初の反応度事故模擬実験であるTS-1について、実験データをまとめたものである。TS-1実験に使用した試験燃料は、初期濃縮度2.79%であり、敦賀1号炉で照射されたBWR7times7型燃料棒を短尺化したものである。短尺化に供した実用燃料のバンドル平均燃焼度は21.3GWd/tであった。NSRRにおける照射実験は、新たに開発した専用の2重カプセルを用い、大気圧・室温の静止水冷却条件下で行い、発熱量61cal/g・fuel(ピークエンタルピ55cal/g・fuel)を与えた。その結果、燃料破損は生じなかった。実験条件、実験方法、燃料燃焼度の測定結果、パルス照射時の燃料の過渡挙動及び照射後検査の結果をまとめて示した。...

  10. Laser Ultrasonic System for Surface Crack Visualization in Dissimilar Welds of Control Rod Drive Mechanism Assembly of Nuclear Power Plant

    Directory of Open Access Journals (Sweden)

    Yun-Shil Choi

    2014-01-01

    Full Text Available In this paper, we propose a J-groove dissimilar weld crack visualization system based on ultrasonic propagation imaging (UPI technology. A full-scale control rod drive mechanism (CRDM assembly specimen was fabricated to verify the proposed system. An ultrasonic sensor was contacted at one point of the inner surface of the reactor vessel head part of the CRDM assembly. Q-switched laser beams were scanned to generate ultrasonic waves around the weld bead. The localization and sizing of the crack were possible by ultrasonic wave propagation imaging. Furthermore, ultrasonic spectral imaging unveiled frequency components of damage-induced waves, while wavelet-transformed ultrasonic propagation imaging enhanced damage visibility by generating a wave propagation video focused on the frequency component of the damage-induced waves. Dual-directional anomalous wave propagation imaging with adjacent wave subtraction was also developed to enhance the crack visibility regardless of crack orientation and wave propagation direction. In conclusion, the full-scale specimen test demonstrated that the multiple damage visualization tools are very effective in the visualization of J-groove dissimilar weld cracks.

  11. COBRA-IV PC: A personal computer version of COBRA-IV-I for thermal-hydraulic analysis of rod bundle nuclear fuel elements and cores

    Energy Technology Data Exchange (ETDEWEB)

    Webb, B.J.

    1988-01-01

    COBRA-IV PC is a modified version of COBRA-IV-I, adapted for use with most IBM PC and PC-compatible desktop computers. Like COBRA-IV-I, COBRA-IV PC uses the subchannel analysis approach to determine the enthalpy and flow distribution in rod bundles for both steady-state and transient conditions. The steady-state and transient solution schemes used in COBRA-IIIC are still available in COBRA-IV PC as the implicit solution scheme option. An explicit solution scheme is also available, allowing the calculation of severe transients involving flow reversals, recirculations, expulsions, and reentry flows, with a pressure or flow boundary condition specified. In addition, several modifications have been incorporated into COBRA-IV PC to allow the code to run on the PC. These include a reduction in the array dimensions, the removal of the dump and restart options, and the inclusion of several code modifications by Oregon State University, most notably, a critical heat flux correlation for boiling water reactor fuel and a new solution scheme for cross-flow distribution calculations. 7 refs., 8 figs., 1 tab.

  12. The photoload sampling technique: estimating surface fuel loadings from downward-looking photographs of synthetic fuelbeds

    Science.gov (United States)

    Robert E. Keane; Laura J. Dickinson

    2007-01-01

    Fire managers need better estimates of fuel loading so they can more accurately predict the potential fire behavior and effects of alternative fuel and ecosystem restoration treatments. This report presents a new fuel sampling method, called the photoload sampling technique, to quickly and accurately estimate loadings for six common surface fuel components (1 hr, 10 hr...

  13. Morphoelastic rods

    CERN Document Server

    Tiero, Alessandro

    2014-01-01

    We propose a mechanical theory describing elastic rods which, like plant organs, can grow and can change their intrinsic curvature and torsion. The equations ruling accretion and remodeling are obtained by combining balance laws involving non-standard forces with constitutive prescriptions filtered by a dissipation principle that takes into account both standard and non-standard working.

  14. Calculation of the linear heat generation rates which violate the thermomechanical limit of plastic deformation of the fuel cladding in function of the burn up of a BWR fuel rod type; Calculo de las razones de generacion de calor lineal que violen el limite termomecanico de deformacion plastica de la camisa en funcion del quemado de una barra combustible tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Lucatero, M.A.; Hernandez L, H. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: mal@nuclear.inin.mx

    2003-07-01

    The linear heat generation rates (LHGR) for a BWR type generic fuel rod, as function of the burnup that violate the thermomechanical limit of circumferential plastic deformation of the can (canning) in nominal operation in stationary state of the fuel rod are calculated. The evaluation of the LHGR in function of the burnt of the fuel, is carried out under the condition that the deformation values of the circumferential plastic deformation of the can exceeds in 0.1 the thermomechanical value operation limit of 1%. The results of the calculations are compared with the generation rates of linear operation heat in function of the burnt for this fuel rod type. The calculations are carried out with the FEMAXI-V and RODBURN codes. The results show that for exhibitions or burnt between 0 and 16,000 M Wd/tU a minimum margin of 160.8 W/cm exists among LHGR (439.6 W/cm) operation peak for the given fuel and maximum LHGR of the fuel (calculated) to reach 1.1% of circumferential plastic deformation of the can, for the peak factor of power of 1.40. For burnt of 20,000 MWd/tU and 60,000 MWd/tU exist a margin of 150.3 and 298.6 W/cm, respectively. (Author)

  15. 压水堆燃料棒在轴向流作用下的随机振动响应研究%Random Response Analysis of PWR Fuel Rod Effect on Axial Flow

    Institute of Scientific and Technical Information of China (English)

    黄恒; 刘彤; 周跃民

    2015-01-01

    Based on random vibration theory ,the random response analysis method of PWR fuel rods under axial flow was established .The fluid force along the axial of rod was treated as a fluctuant random load ,and the mode shape method and power spectrum analysis method were used to derive the empirical formula of RMS response .This article provides a theoretical analysis method w hich does not rely on the flow induced vibration test of fuel assembly .The effects for the RMS response of fuel rods by the equivalent velocity ,turbulence intensity ,and correlation length factor were discussed .The method can meet the requirements of engineering analysis . The results show that the RMS response of fuel rods will increase with the equivalent velocity ,turbulence intensity and the correlation length factor .The response is more sensitive to the equivalent velocity and coefficient length factor changes ,and linearly with the turbulence intensity .In the operating condition of the pressurized water reactor (PWR) ,the RMS amplitude of fuel rods is about micrometers .%基于随机振动理论,建立了在轴向流作用下压水堆燃料棒随机响应的纯理论分析方法。将流体力考虑为沿燃料棒轴向位置的脉冲随机荷载,结合模态分析技术,从功率谱分析法推导出燃料棒振动均方根响应的表达式。提供了一套不依赖燃料组件流致振动实验的纯理论分析方法,重点分析了等效流速、湍流强度、相关长度系数等几个主要流场参数对结构均方根响应的影响。结果表明,本文计算模型的精度满足工程分析要求,燃料棒响应随等效流速、湍流强度和相关长度系数的增大而增大;其中响应对于等效流速和相关长度系数的变化较为敏感,而与湍流强度呈线性变化关系;在压水堆运行中的燃料棒均方根幅值约处在μm量级。

  16. Analysis on Common Defects on the Surface of Hot Rolled Wire Rods%热轧盘条常见表面缺陷分析

    Institute of Scientific and Technical Information of China (English)

    汪先虎; 姜洪刚; 吴东明

    2014-01-01

    介绍了热轧盘条常见的各类表面缺陷,结合金相微观分析方法,对盘条不同表面缺陷的典型微观形貌和金相组织形态进行分类与分析,从连铸与轧制工艺角度追溯了盘条表面缺陷产生的原因,提出了相应解决方案。%All kinds of common defects on the surface of hot rolled wired rods are introduced, and then typical microstructures and metallographic structure forms of different defects on the sur-face of wire rods are classified and analyzed by metallographic microscopic analysis method. Fi-nally the corresponding solution for dealing with these defects is proposed based on getting the causes leading to the defects on the surface of wire rods through analysis of the continuous casting and rolling process.

  17. Study of a criticality accident involving fuel rods and water outside a power reactor; Etude d'un accident de criticite mettant en presence des crayons combustibles et de l'eau hors reacteur de puissance

    Energy Technology Data Exchange (ETDEWEB)

    Beloeil, L

    2000-05-30

    It is possible to imagine highly unlikely but numerous accidental situations where fuel rods come into contact with water under conditions close to atmospheric values. This work is devoted to modelling and simulation of first instants of the power excursion that may result from such configurations. We show that void effect is a preponderant feedback for most severe accidents. The formation of a vapour film around the rods is put forward and confirmed with the help of experimental transients using electrical heating. We propose then a vapour/liquid flow model able to reproduce void fraction evolution. The vapour film is treated as a compressible medium. Conservation balance equations are solved on a moving mesh with a two-dimensional scheme and boundary conditions taking notice of interfacial phenomena and axial escape possibility. Movements of the liquid phase are modelled through a non-stationary integral equation and a dissipative term suited to the particular geometry of this flow. The penetration of energy into the liquid is also calculated. Thus, the coupling of aerodynamic and hydrodynamic modules gives results in excellent agreement with experiments. Next, neutronic phenomena into the fuel pellet, their feedback effects and the distribution of power through the rod are numerically translated. For each developed module, validation tests are provided. Then, it is possible to simulate the first seconds of the whole criticality accident. Even if this calculation tool is only a way of study as a first approach, performed simulations are proving coherent with reported data on recorded accidents. (author)

  18. Turbulence Model Evaluation Study for a Secondary Flow and a Flow Pulsation in the Sub-Channels of an 18-Finned Rod Bundle by Using Computational Fluid Dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jong Hark; Chae, Hee Taek; Park, Cheol; Kim, Heon Il

    2008-09-15

    Since the heat flux of the rod type fuel used in the HANARO, a research reactor being operated in the KAERI, is substantially higher than the heat flux of power reactors, the HANARO fuel has 8 longitudinal fins for enhancing the heat release from the fuel rod surface. This unique shape of a nuclear fuel led us to study the flows and thermal hydraulic characteristics of it. Especially because the flows through the narrow channels built up by these finned rod fuels would be different from the flow characteristics in the coolant channels formed by bare rod fuels, some experimental studies to investigate the flow behaviors and structures in a finned rod bundle were done by other researchers. But because of the very complex geometries of the flow channels in the finned rod bundle only allowed us to obtain limited information about the flow characteristics, a numerical study by a computational fluid dynamics technique has been adopted to elucidate more about such a complicated flow in a finned rod bundle. In this study, for the development of an adequate computational model to simulate such a complex geometry, a mesh sensitivity study and the effects of various turbulence models were examined. The CFD analysis results were compared with the experimental results. Some of them have a good agreement with the experimental results. All linear eddy viscosity turbulence models could hardly predict the secondary flows near the fuel surfaces and in the sub-channel, but the RSM (Reynolds Stress Model) revealed very different results from the eddy viscosity turbulence models. In the transient analysis all turbulence model predicted flow pulsation at the center of a subchannel as well as at the gap between rods in spite of large P/D. The flow pulsation showed different results with turbulence models and the location in the sub-channels.

  19. Surface fuel changes after severe disturbances in northern Rocky Mountain ecosystems

    Science.gov (United States)

    Chris Stalling; Robert E. Keane; Molly Retzlaff

    2017-01-01

    It is generally assumed that severe disturbances predispose damaged forests to high fire hazard by creating heavy fuel loading conditions. Of special concern is the perception that surface fuel loadings become high as recently killed trees deposit foliage and woody material on the ground and that these high fuel loadings may cause abnormally severe fires. This study...

  20. Performance of fire behavior fuel models developed for the Rothermel Surface Fire Spread Model

    Science.gov (United States)

    Robert Ziel; W. Matt Jolly

    2009-01-01

    In 2005, 40 new fire behavior fuel models were published for use with the Rothermel Surface Fire Spread Model. These new models are intended to augment the original 13 developed in 1972 and 1976. As a compiled set of quantitative fuel descriptions that serve as input to the Rothermel model, the selected fire behavior fuel model has always been critical to the resulting...

  1. Neutron Flux Depression in the UO{sub 2}-PuO{sub 2}(15 to 30%) Fuel Rods from IVO-FR2-Vg7-Irradiation Experiment; Depresion de flujo neutronico en las barras combustibles de UO2-PuO2(15 al 30%) del experimento de irradiacion IVO-FR2-Vg7

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, J.; Fernandez, J. L.

    1983-07-01

    The thermal-neutron flux depression within a fuel rod has a great influence in the radial temperature profile of the rod, especially for high enrichment fuel. For this reason, a study was made about the UO{sub 2}-PUO{sub 2} (15 to 30% PUO{sub 2}) fuel pins for the KfK-JEN joint irradiation program IVO, in the FR2 reactor. Different methods (diffusion, Bonalumi, successive generations) were compared and a new approach (parabolic approximation) was developed. (Author) 22 refs.

  2. Modeling of the PWR fuel mechanical behaviour and particularly study of the pellet-cladding interaction in a fuel rod; Contribution a la modelisation du comportement mecanique des combustibles REP sous irradiation, avec en particulier le traitement de l`interaction pastille-gaine dans un crayon combustible

    Energy Technology Data Exchange (ETDEWEB)

    Hourdequin, N.

    1995-05-01

    In Pressurized Water Reactor (PWR) power plants, fuel cladding constitutes the first containment barrier against radioactive contamination. Computer codes, developed with the help of a large experimental knowledge, try to predict cladding failures which must be limited in order to maintain a maximal safety level. Until now, fuel rod design calculus with unidimensional codes were adequate to prevent cladding failures in standard PWR`s operating conditions. But now, the need of nuclear power plant availability increases. That leads to more constraining operating condition in which cladding failures are strongly influenced by the fuel rod mechanical behaviour, mainly at high power level. Then, the pellet-cladding interaction (PCI) becomes important, and is characterized by local effects which description expects a multidimensional modelization. This is the aim of the TOUTATIS 2D-3D code, that this thesis contributes to develop. This code allows to predict non-axisymmetric behaviour too, as rod buckling which has been observed in some irradiation experiments and identified with the help of TOUTATIS. By another way, PCI is influenced by under irradiation experiments and identified with the help of TOUTATIS which includes a densification model and a swelling model. The latter can only be used in standard operating conditions. However, the processing structure of this modulus provides the possibility to include any type of model corresponding with other operating conditions. In last, we show the result of these fuel volume variations on the cladding mechanical conditions. (author). 25 refs., 89 figs., 2 tabs., 12 photos., 5 appends.

  3. Eulerian formulation of elastic rods

    Science.gov (United States)

    Huynen, Alexandre; Detournay, Emmanuel; Denoël, Vincent

    2016-06-01

    In numerous biological, medical and engineering applications, elastic rods are constrained to deform inside or around tube-like surfaces. To solve efficiently this class of problems, the equations governing the deflection of elastic rods are reformulated within the Eulerian framework of this generic tubular constraint defined as a perfectly stiff normal ringed surface. This reformulation hinges on describing the rod-deformed configuration by means of its relative position with respect to a reference curve, defined as the axis or spine curve of the constraint, and on restating the rod local equilibrium in terms of the curvilinear coordinate parametrizing this curve. Associated with a segmentation strategy, which partitions the global problem into a sequence of rod segments either in continuous contact with the constraint or free of contact (except for their extremities), this re-parametrization not only trivializes the detection of new contacts but also transforms these free boundary problems into classic two-points boundary-value problems and suppresses the isoperimetric constraints resulting from the imposition of the rod position at the extremities of each rod segment.

  4. Description of modelling to be implemented in the fuel rod thermomechanics code Cyrano3; Description des modeles a introduire dans le logiciel de thermomecanique du crayon combustible Cyrano3

    Energy Technology Data Exchange (ETDEWEB)

    Baron, D.; Bouffioux, P.

    1993-06-01

    CYRANO3 is the new EDF thermomechanical code developed to evaluate the overall fuel rod behavior under irradiation. In that context, this paper presents the phenomena to be simulated and the correlations adopted for modelling purposes. The empirical models presented are taken from the CYRANO2 code and a compilation of the relevant literature. The present revision corrects and supplements version B on the basis of its use during the software coding phase from January 1991 to May 1993. (authors). figs., tabs., 120 refs.

  5. Nuclear thermionic converter. [tungsten-thorium oxide rods

    Science.gov (United States)

    Phillips, W. M.; Mondt, J. F. (Inventor)

    1977-01-01

    Efficient nuclear reactor thermionic converter units are described which can be constructed at low cost and assembled in a reactor which requires a minimum of fuel. Each converter unit utilizes an emitter rod with a fluted exterior, several fuel passages located in the bulges that are formed in the rod between the flutes, and a collector receiving passage formed through the center of the rod. An array of rods is closely packed in an interfitting arrangement, with the bulges of the rods received in the recesses formed between the bulges of other rods, thereby closely packing the nuclear fuel. The rods are constructed of a mixture of tungsten and thorium oxide to provide high power output, high efficiency, high strength, and good machinability.

  6. Experimental investigation of heat transfer from a 2 × 2 rod bundle to supercritical pressure water

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Han [State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Bi, Qincheng, E-mail: qcbi@mail.xjtu.edu.cn [State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Wang, Linchuan; Lv, Haicai [State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Leung, Laurence K.H. [Atomic Energy of Canada Limited, Chalk River, Ont., Canada K0J 1J0 (Canada)

    2014-08-15

    Highlights: • Heat transfer of supercritical water through a 2 × 2 rod bundles is investigated. • Circumferential wall temperature distribution is obtained. • Effects of system parameters on heat transfer characteristics are analyzed. • Heat transfer correlations are compared against the rod bundle test data. - Abstract: Heat transfer experiments with supercritical pressure water flowing vertically upward through a 2 × 2 rod bundle have been performed at Xi’an Jiaotong University. A fuel-assembly simulator with four heated rods was installed inside a square channel with rounded corner. The outer diameter of each heated rod is 8 mm with an effective heated length of 600 mm. The experiments covered the pressure range of 23–28 MPa, mass-flux range of 350–1000 kg/(m{sup 2} s) and heat-flux range on the rod surface of 200–1000 kW/m{sup 2}. Heat transfer characteristics of supercritical pressure water through the bundle were examined with respect to variations of heat flux, system pressure, and mass flux. These characteristics were shown to be similar to those previously observed in tubes or annuli. The experimental data indicate a non-uniform circumferential wall-temperature distribution around the heated rod. A maximum wall temperature was observed at the surface facing the corner gap between the heated rod and the ceramic tube, while the minimum wall temperature was observed at the surface facing the center subchannel. The difference between maximum and minimum wall temperatures varies with heat flux and/or mass flux. Eight heat transfer correlations developed for supercritical water were assessed against the current set of test data. Prediction of the Jackson correlation agrees closely with the experimental Nusselt number. A new correlation has been derived based on Jackson correlation to improve the prediction accuracy of supercritical heat transfer coefficient in a 2 × 2 rod bundle.

  7. Degradation in steam of 60 cm-long B4C control rods

    Science.gov (United States)

    Dominguez, C.; Drouan, D.

    2014-08-01

    In the framework of nuclear reactor core meltdown accident studies, the degradation of boron carbide control rod segments exposed to argon/steam atmospheres was investigated up to about 2000 °C in IRSN laboratories. The sequence of the phenomena involved in the degradation has been found to take place as expected. Nevertheless, the ZrO2 oxide layer formed on the outer surface of the guide tube was very protective, significantly delaying and limiting the guide tube failure and therefore the boron carbide pellet oxidation. Contrary to what was expected, the presence of the control rod decreases the hydrogen release instead of increasing it by additional oxidation of boron compounds. Boron contents up to 20 wt.% were measured in metallic mixtures formed during degradation. It was observed that these metallic melts are able to attack the surrounding fuel rods, which could have consequences on fuel degradation and fission product release kinetics during severe accidents.

  8. The Vaporization Behavior of a Fuel Drop on a Hot Surface

    Science.gov (United States)

    1977-11-01

    evaporation behavior of fuel drops 99 Figure 36. Effect of surface cleanliness on drop evaporation lifetime .. ......... . 101 Figure 37. Effect of drop...C, CD 0 C) - -C) -H _______________C_ 100 procedures that were considered during the evaluation included the surface cleanliness , fuel drop size and...evaporating surface heating rate. The effect of the studied variables on the test results was found to be as follow: Surface Cleanliness As indicated

  9. Nonuniform Oxidation on the Surface of Fuel Element in HTR

    Directory of Open Access Journals (Sweden)

    Peng Liu

    2016-01-01

    Full Text Available The graphite oxidation of fuel element has obtained high attention in air ingress accident analysis of high temperature gas-cooled reactor (HTR. The shape function, defined as the relationship between the maximum and the average of the oxidation, is an important factor to estimate the consequence of the accident. There are no detailed studies on the shape function currently except two experiments several decades ago. With the development of computer technology, CFD method is used in the numerical experiment about graphite oxidation in pebble bed of HTR in this paper. Structured packed beds are used in the calculation instead of random packed beds. The result shows the nonuniform distribution of oxidation on the sphere surface and the shape function in the condition of air ingress accident. Furthermore, the sensitive factors of shape function, such as temperature and Re number, are discussed in detail and the relationship between the shape function and sensitive factors is explained. According to the results in this paper, the shape function ranges from 1.05 to 4.7 under the condition of temperature varying from 600°C to 1200°C and Re varying from 16 to 1600.

  10. 精轧和吐丝温度对焊丝钢盘条表面红锈影响研究%Effect of finish rolling and wire rod laying temperature on surface red rust of wire rod for welding wire steel

    Institute of Scientific and Technical Information of China (English)

    郭大勇; 任玉辉; 王秉喜; 高航; 韩立涛; 车安

    2013-01-01

    对不同精轧和吐丝温度条件下焊丝钢盘条表面红锈情况进行对比分析.通过盘条氧化铁皮成分分析发现,出现红锈的铁皮中Fe3O4、Fe2O3含量较高.通过热力学分析发现,盘条与空气和水等介质反应,在高温条件下,有利于FeO的形成,较低的精轧和吐丝温度易于导致氧化铁皮Fe3O4、Fe2O3含量较高.同时,在较低精轧和吐丝温度条件下,盘条表面氧化铁皮的破裂,使FeO不断被氧化成Fe3O4、Fe2O3.在2种因素作用下,盘条表面易出现红锈.提高精轧和吐丝温度,可消除盘条表面红锈.%To analyze the surface red rust of wire rod for welding wire steel in different finish rolling and wire rod laying temperature conditions. It is found that red rust has higher content of Fe3O4 and Fe2O3 after wire rod scale composition is analyzed. It is found through thermomechanical analysis that FeO is easy to form in high temperature through reaction between wire rod and medium such as air and water, lower finish rolling and wire rod laying temperature cause higher content of Fe3O4 and Fe2O3 in scale. At the same time, cracks of wire rod surface scale cause FeO oxidized to Fe3O4 and Fe2O3 in condition of lower finish rolling and wire rod laying temperature. Red rust occurs easily on wire rod surface in two factors. Red rust can be prevented by increasing finish rolling and wire rod laying temperature.

  11. A robotized surface workstation for manipulation, filling and closing of packaging containers for spent nuclear fuel

    Energy Technology Data Exchange (ETDEWEB)

    Bartos, Pavel [FITE a.s., Ostrava-Marianske Hory (Czech Republic); Haladova, Petra [Robotsystem, LLC/Moravian Research, LLC, Ostrava-Moravska (Czech Republic); Otcenasek, Petr

    2016-01-15

    Options for the handling of spent nuclear fuel are described and a packaging cask for an underground repository is presented as also a robotic surface workplace for the repository. The potential for the closing the nuclear fuel cycle is discussed. Currently, a team of Czech experts is developing a project of fully robotic technology for manipulation and storage of packaging casks for spent nuclear fuel in host rock of underground repository.

  12. Spherical and rod-like dialdehyde cellulose nanocrystals by sodium periodate oxidation: Optimization with double response surface model and templates for silver nanoparticles

    Directory of Open Access Journals (Sweden)

    F-F. Lu

    2016-12-01

    Full Text Available A novel double response surface model is used first time to optimize a regioselective process to prepare spherical dialdehyde cellulose nanocrystals (SDACN and rod-like dialdehyde cellulose nanocrystals (RDACN via one-step sodium periodate (NaIO4 oxidation. The influence of four preparation factors (solid-liquid ratio, NaIO4 concentration, reaction time and temperature on the yields and aldehyde contents of the final products were evaluated. For comparison, rod-like cellulose nanocrystals (CN-M and CN-S were prepared by hydrochloric/formic acid hydrolysis and sulfuric acid hydrolysis, respectively. The RDACN shows high crystallinity of 82%, while SDACN presents low crystallinity due to the high degree of oxidation. Thus, SDACN has poorer thermal stability than RDACN and CN-M, but higher than CN-S. Compared to CN-M, SDACN with higher aldehyde contents as templates is beneficial to deposit more Ag nanoparticles with diameters of 30±4 nm and the resultant nanohybrids exhibit good antibacterial activities against both Gram-negative E. coli and Gram-positive S. aureus.

  13. Failure behavior of plutonium-uranium mixed oxide fuel under reactivity-initiated accident condition

    Science.gov (United States)

    Abe, T.; Nakae, N.; Kodato, K.; Matsumoto, M.; Inabe, T.

    1992-06-01

    Two series of in-pile tests on MOX fuels were performed in the NSRR to study failure behavior under RIA (reactivity-initiated accident) conditions in water cooled reactors. PWR type MOX test rods were pulsed in a first series. The test rods were designed to have dimensions identical to standard UO 2 fuel, on which a large number of tests had been conducted previously. The test result was that the failure mechanism and the threshold of MOX fuel was consistent with those of UO 2 fuel. ATR-type MOX test rods with PuO 2 particles as well as reference rods without PuO 2 particles were subjected to pulsing in a second series. PuO 2 particles of 400 and 1100 μm in diameter were artificially embedded at the surface of MOX pellets. No effect of particles appeared on the threshold, and no significant indication of their effect was observed on the cladding.

  14. Irradiation analysis, production test IP-672, HAPO 238, irradiation of impacted UO{sub 2}-PuO{sub 2} fuel rod bundles in C reactor

    Energy Technology Data Exchange (ETDEWEB)

    Cox, J.H.

    1964-09-14

    The loss of flow is considered as far as the flow to the inlet hydraulic connector, inlet plugging and water shutoff time. A mockup revealed no vibration of the fuel element bundles and at the low temperatures present there should be no problem of corrosion. Efforts to assure safety with plutonium in the fuel elements are noted. (GHH)

  15. Approximate solutions of the equation of motion’s of the rigid rod which rocks on the circular surface without slipping

    Directory of Open Access Journals (Sweden)

    Md. Alal Hosen

    2014-09-01

    Full Text Available In this paper, a modified harmonic balance method based an analytical technique has been developed to determine approximate solutions for a strongly nonlinear oscillator with a discontinuous term which is arising from the motion of rigid rod on the surface without slipping. Usually, a set of nonlinear algebraic equations is solved in this method. However, analytical solutions of these algebraic equations are not always possible, especially in the case of a large oscillation. We have been compared the solution results of this method with the numerical solution in order to validate the approach and assess the accuracy of the solutions has been demonstrated and discussed. We found that, a second order modified harmonic balance method works very well for the whole range of initial amplitudes. The advantage of the using method is its simple procedure and gives almost similar results in comparison with the exact solution.

  16. Response Surface Methodology Control Rod Position Optimization of a Pressurized Water Reactor Core Considering Both High Safety and Low Energy Dissipation

    Directory of Open Access Journals (Sweden)

    Yi-Ning Zhang

    2017-02-01

    Full Text Available Response Surface Methodology (RSM is introduced to optimize the control rod positions in a pressurized water reactor (PWR core. The widely used 3D-IAEA benchmark problem is selected as the typical PWR core and the neutron flux field is solved. Besides, some additional thermal parameters are assumed to obtain the temperature distribution. Then the total and local entropy production is calculated to evaluate the energy dissipation. Using RSM, three directions of optimization are taken, which aim to determine the minimum of power peak factor Pmax, peak temperature Tmax and total entropy production Stot. These parameters reflect the safety and energy dissipation in the core. Finally, an optimization scheme was obtained, which reduced Pmax, Tmax and Stot by 23%, 8.7% and 16%, respectively. The optimization results are satisfactory.

  17. Development of a fuel-rod simulator and small-diameter thermocouples for high-temperature, high-heat-flux tests in the Gas-Cooled Fast Reactor Core Flow Test Loop

    Energy Technology Data Exchange (ETDEWEB)

    McCulloch, R.W.; MacPherson, R.E.

    1983-03-01

    The Core Flow Test Loop was constructed to perform many of the safety, core design, and mechanical interaction tests in support of the Gas-Cooled Fast Reactor (GCFR) using electrically heated fuel rod simulators (FRSs). Operation includes many off-normal or postulated accident sequences including transient, high-power, and high-temperature operation. The FRS was developed to survive: (1) hundreds of hours of operation at 200 W/cm/sup 2/, 1000/sup 0/C cladding temperature, and (2) 40 h at 40 W/cm/sup 2/, 1200/sup 0/C cladding temperature. Six 0.5-mm type K sheathed thermocouples were placed inside the FRS cladding to measure steady-state and transient temperatures through clad melting at 1370/sup 0/C.

  18. Radiological and nuclear safety aspects in the fabrication of 1.8% enriched U O{sub 2} fuel rods for the RA-8 critical facility; Aspectos de seguridad radiologica y nuclear en la fabricacion de barras combustibles, con U O{sub 2} enriquecido al 1.8%, para la facilidad critica RA-8

    Energy Technology Data Exchange (ETDEWEB)

    Cardenas, Hugo; Becarra, Fabian; Herrero, Jorge; Luna, Manuel; Perez, Aldo [Comision Nacional de Energia Atomica, (Argentina). Centro Atomico Constituyentes

    1997-10-01

    The neutronic behavioral study of the fuel for the future nuclear reactor CAREM required to mount critical facility with 1.8% enriched U O{sub 2} fuel rods. The present work describes the various operation and production processes, the safety and radioprotection systems, the administrative procedures and the associated radiological controls. Also, the results obtained in the area and personal monitoring and waste generation are detailed. (author). 10 refs., 4 figs., 1 tab.

  19. Preliminary Drop Time Analysis of a Control Rod Using CFD Code

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Myoung Hwan; Park, Jin Seok; Lee, Won Jae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Jun Hong [SEST Co., Seoul (Korea, Republic of)

    2010-05-15

    A control rod drive mechanism (CRDM) is a reactor regulating system, which can insert and withdraw a control rod containing a neutron absorbing material to control the reactivity of the reactor core. The latch type CRDM for the SMART (System-integrated Modular Advanced ReacTor) is going to be used. The drop time of the control rod in the design stage is one of important parameters for a safety analysis of the reactor. When the control rod is falling down into the core, it is retarded by various forces acting on it such as fluid resistance buoyancy and mechanical friction caused by contacting the inner surface of the guide thimble, etc.. However, complicated coupling of the various forces makes it difficult to predict the drop behavior. This paper describes the development of the 3D CFD analysis model using a FLUENT code. The single control rod of the Westinghouse 17x17 type optimized fuel assembly (W-OFA) was considered for the verification of the CFD model. A preliminary drop time analysis for the SMART with the simulated control rod was performed

  20. COBRA-IV-I: an interim version of COBRA for thermal-hydraulic analysis of rod bundle nuclear fuel elements and cores

    Energy Technology Data Exchange (ETDEWEB)

    Wheeler, C.L.; Stewart, C.W.; Cena, R.J.; Rowe, D.S.; Sutey, A.M.

    1976-03-01

    The COBRA-IV-I computer code uses the subchannel analysis approach to determine the enthalpy and flow distribution in rod bundles for both steady-state and transient conditions. The steady-state and transient solution schemes used in COBRA-IIIC are still available in COBRA-IV-I as the implicit solution scheme option. In addition to these techniques, a new explicit solution scheme is now available which allows the calculation of severe transients involving flow reversals, recirculations, expulsion and reentry flows, with a pressure or flow boundary condition specified. Significant storage compaction and reduced running times have been achieved to allow the calculation of problems involving hundreds of subchannels.

  1. The Software Design for252Cf Neutron Activation Fuel Rod 235U Enrichment Inspecting Equipment%252Cf中子活化核燃料棒235U富集度检测设备的软件设计

    Institute of Scientific and Technical Information of China (English)

    张雷; 刘明; 马金波

    2013-01-01

    It introduces the software design for 252Cf neutron activation fuel red235U enrichment inspecting equipment.It used multithread technique to control Advantech PCI-1780 counter/timer card,and collect γ-ray signal from the six-path detectors.Process and analyze the collected data can exactly check the actual 235U enrichment and abnormal pellets in the nuclear fuel rods.The software can measure the actual 235U enrichment and judge whether there are abnormal pellets in the nuclear fuel rods accurately,and send customizing messages to PLC which complete automatic sorting,at 6 m/min detection speed.Now the software is used on nondestructive test equipment in Nuclear Fuel Element Factory.%介绍了252Cf中子活化核燃料棒235U富集度检测设备的软件设计,该软件采用多线程技术控制研华PCI-1780采集卡定时采集六路探测器输出的经252Cf中子活化后235U裂变产物的γ射线信号,针对采集数据的特性,进行相应的处理和分析,可以检测出核燃料棒的实际235U富集度以及有无异常芯块.该软件经过实验验证在检测速度为6时,能够准确测量核燃料棒的实际235U富集度值并判断棒中是否混有异常芯块,同时向PLC发送相应信号实现自动分选.目前已应用在核燃料元件厂的核燃料棒235U富集度无损检测设备上.

  2. Using Finite Model Analysis and Out of Hot Cell Surrogate Rod Testing to Analyze High Burnup Used Nuclear Fuel Mechanical Properties

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jy-An John [ORNL; Jiang, Hao [ORNL; Wang, Hong [ORNL

    2014-07-01

    Based on a series of FEA simulations, the discussions and the conclusions concerning the impact of the interface bonding efficiency to SNF vibration integrity are provided in this report; this includes the moment carrying capacity distribution between pellets and clad, and the impact of cohesion bonding on the flexural rigidity of the surrogate rod system. As progressive de-bonding occurs at the pellet-pellet interfaces and at the pellet-clad interface, the load ratio of the bending moment carrying capacity gradually shifts from the pellets to the clad; the clad starts to carry a significant portion of the bending moment resistance until reaching the full de-bonding state at the pellet-pellet interface regions. This results in localized plastic deformation of the clad at the pellet-pellet-clad interface region; the associated plastic deformations of SS clad leads to a significant degradation in the stiffness of the surrogate rod. For instance, the flexural rigidity was reduced by 39% from the perfect bond state to the de-bonded state at the pellet-pellet interfaces.

  3. Development of surface enhanced Raman scattering (SERS) spectroscopy monitoring of fuel markers to prevent fraud

    Science.gov (United States)

    Wilkinson, Timothy; Clarkson, John; White, Peter C.; Meakin, Nicholas; McDonald, Ken

    2013-05-01

    Governments often tax fuel products to generate revenues to support and stimulate their economies. They also subsidize the cost of essential fuel products. Fuel taxation and subsidization practices are both subject to fraud. Oil marketing companies also suffer from fuel fraud with loss of legitimate sales and additional quality and liability issues. The use of an advanced marking system to identify and control fraud has been shown to be effective in controlling illegal activity. DeCipher has developed surface enhanced Raman scattering (SERS) spectroscopy as its lead technology for measuring markers in fuel to identify and control malpractice. SERS has many advantages that make it highly suitable for this purpose. The SERS instruments are portable and can be used to monitor fuel at any point in the supply chain. SERS shows high specificity for the marker, with no false positives. Multiple markers can also be detected in a single SERS analysis allowing, for example, specific regional monitoring of fuel. The SERS analysis from fuel is also quick, clear and decisive, with a measurement time of less than 5 minutes. We will present results highlighting our development of the use of a highly stable silver colloid as a SERS substrate to measure the markers at ppb levels. Preliminary results from the use of a solid state SERS substrate to measure fuel markers will also be presented.

  4. Transcriptome Dynamics of Developing Photoreceptors in Three-Dimensional Retina Cultures Recapitulates Temporal Sequence of Human Cone and Rod Differentiation Revealing Cell Surface Markers and Gene Networks.

    Science.gov (United States)

    Kaewkhaw, Rossukon; Kaya, Koray Dogan; Brooks, Matthew; Homma, Kohei; Zou, Jizhong; Chaitankar, Vijender; Rao, Mahendra; Swaroop, Anand

    2015-12-01

    The derivation of three-dimensional (3D) stratified neural retina from pluripotent stem cells has permitted investigations of human photoreceptors. We have generated a H9 human embryonic stem cell subclone that carries a green fluorescent protein (GFP) reporter under the control of the promoter of cone-rod homeobox (CRX), an established marker of postmitotic photoreceptor precursors. The CRXp-GFP reporter replicates endogenous CRX expression in vitro when the H9 subclone is induced to form self-organizing 3D retina-like tissue. At day 37, CRX+ photoreceptors appear in the basal or middle part of neural retina and migrate to apical side by day 67. Temporal and spatial patterns of retinal cell type markers recapitulate the predicted sequence of development. Cone gene expression is concomitant with CRX, whereas rod differentiation factor neural retina leucine zipper protein (NRL) is first observed at day 67. At day 90, robust expression of NRL and its target nuclear receptor NR2E3 is evident in many CRX+ cells, while minimal S-opsin and no rhodopsin or L/M-opsin is present. The transcriptome profile, by RNA-seq, of developing human photoreceptors is remarkably concordant with mRNA and immunohistochemistry data available for human fetal retina although many targets of CRX, including phototransduction genes, exhibit a significant delay in expression. We report on temporal changes in gene signatures, including expression of cell surface markers and transcription factors; these expression changes should assist in isolation of photoreceptors at distinct stages of differentiation and in delineating coexpression networks. Our studies establish the first global expression database of developing human photoreceptors, providing a reference map for functional studies in retinal cultures.

  5. 一种适用于十字形控制棒的超临界燃料组件设计%Supercritical Fuel Assembly Design Applicable for Cruciform Control Rod

    Institute of Scientific and Technical Information of China (English)

    朱发文; 雷涛; 程华旸; 庞华; 彭园; 茹俊

    2013-01-01

    The supercritical water-cooled reactor (SCWR) has been selected as one of the most promising reactors for Generation IV nuclear reactors due to its higher thermal efficiency and more simplified structure compared to state-of-the-art LWRs.However, its higher outlet temperature and higher temperature difference between inlet and outlet bring much challenge to the design of SCWR fuel assembly.In this paper, the present status of supercritical fuel assembly design at home and abroad is studied and a kind of fuel assembly with two-flow structure applying for cruciform control rod is proposed.The results show that, the design basically meets the requirements of fuel assemhly design, which has good performance.%超临界水冷堆(SCWR)是目前最有应用前景的第四代反应堆堆型之一,与现有轻水堆相比,具有热效率高、结构简单等诸多优势.但SCWR较高的出口温度以及进出口温差给SCWR燃料组件设计带来了很大的挑战.本文研究国内外超临界燃料组件设计的研究现状,提出一种适用于十字形控制棒的双流程燃料组件设计方案.结果表明,该方案基本满足超临界燃料组件的设计要求,具有较好的综合性能.

  6. Analysis of Equilibrium with Friction of an Elastic Rod Constrained by a Cylindrical Surface%受圆柱面约束弹性细杆的摩擦平衡分析

    Institute of Scientific and Technical Information of China (English)

    薛纭; 刘昭

    2016-01-01

    Under background of a class of engineering object,the problem of equilibrium with friction of an elastic rod constrained by a cylindrical surface was investigated in this paper.On the basis of the analysis of the configuration and the motion of the circular-cross-section elastic rod constrained by the cylindrical surface,differential equations of the equilibrium with the distributed friction were derived and transformed into dimensionless form.Conditions for the existence of solutions of the screw rod without the friction were obtained,as well as conditions for no relative sliding between the elastic rod and the cylinder surface with the friction.It was found that the deformation expressed by the first derivative of nutation angle and the second derivative of since angle with respect to the arc coordinate was induced by the distributed friction.For five types of special configuration of elastic rod in equilibrium,principal vector of internal forces on cross sections of the rod and distributions of friction force were predicted analytically.Then some types were discussed numerically to determine whether the rod would be balanced.This paper provides possible methods and ideas for further studying the statics and the dynamics of elastic rods constrained by surfaces with friction.%以一类工程对象为背景,研究圆柱面约束下的弹性杆的摩擦平衡问题.在对圆柱面上圆截面弹性杆位形和运动分析的基础上,导出了计入分布摩擦力的弹性杆平衡微分方程并无量纲化.由此得到了无摩擦时螺旋杆解的存在条件,以及存在摩擦时的不滑动的条件.分析表明,截面章动角对弧坐标的一阶导数和自转角对弧坐标的二阶导数表达的变形是分布摩擦力所致.就5类特殊的平衡位形,分别计算了内力和分布摩擦力集度,部分进行了数值计算,给予了静止与否的判定.为曲面上弹性杆的摩擦平衡或动力学分析提供方法和思路.

  7. Tie rod insertion test

    CERN Multimedia

    B. LEVESY

    2002-01-01

    The superconducting coil is inserted in the outer vaccum tank and supported by a set of tie rods. These tie rods are made of titanium alloy. This test reproduce the final insertion of the tie rods inside the outer vacuum tank.

  8. Influence on rewetting temperature and wetting delay during rewetting rod bundle by various radial jet models

    Energy Technology Data Exchange (ETDEWEB)

    Debbarma, Ajoy; Pandey, Krishna Murari [National Institute of Technology, Assam (India). Dept. of Mechanical Engineering

    2016-03-15

    Numerical investigation of the rewetting of single sector fuel assembly of Advanced Heavy Water Reactor (AHWR) has been carried out to exhibit the effect of coolant jet diameters (2, 3 and 4 mm) and jet directions (Model: M, X and X2). The rewetting phenomena with various jet models are compared on the basis of rewetting temperature and wetting delay. Temperature-time curve have been evaluated from rods surfaces at different circumference, radial and axial locations of rod bundle. The cooling curve indicated the presence of vapor in respected location, where it prevents the contact between the firm and fluid phases. The peak wall temperature represents as rewetting temperature. The time period observed between initial to rewetting temperature point is wetting delay. It was noted that as improved in various jet models, rewetting temperature and wetting delay reduced, which referred the coolant stipulation in the rod bundle dominant vapor formation.

  9. Ignition probability of fine dead surface fuels in native Patagonian forests of Argentina

    OpenAIRE

    Lucas O. Bianchi; Guillermo E. Defosse

    2016-01-01

     Aim of study: The Canadian Forest Fire Weather Index (FWI) is being implemented all over the world. This index is being adapted to the Argentinean ecosystems since the year 2000. With the objective of calibrating the Fine Fuel Moisture Code (FFMC) of the FWI system to Patagonian forests, we studied the relationship between ignition probability and fine dead surface fuel moisture content (MC) as an indicator of potential fire ignition. Area of study: The study area is located in northwestern ...

  10. Description and characterization of HBWR Series H-1 test rods

    Energy Technology Data Exchange (ETDEWEB)

    Wagoner, S.R.; Barner, J.O.; Welty, R.K.

    1979-06-01

    The as-built characterization results are presented for the HBWR Series H-1 test rods to be irradiated as part of the Fuel Performance Improvement Program (FPIP). The irradiation of these rods is to be conducted in the Halden Boiling Water Reactor (HBWR). Series H-1 consists of twelve rods for irradiation and six spares. Rod design types include (1) a reference dished pellet design, (2) an annular pellet design, (3) an annular pellet design combined with graphite-coated cladding, and (4) a packed-particle (vipac) design. The report, which describes the fabrication and detailed characterization results for the rods, is divided into four major sections: (1) experiment description, (2) process development required to fabricate the test rods, (3) methods and procedures used to fabricate and characterize the rods, and (4) a summary of the characterization results.

  11. ENUSA-TECNATOM collaboration project: improvements to the system of inspection by UT's circular fresh fuel rod welding; Proyecto colaboraci0n ENUSA-TECNATOM: Mejoras en el sistema de inspeccion por UT de la soldadura circular de la barra combustible fresca

    Energy Technology Data Exchange (ETDEWEB)

    Gallardo, J.; Toral, M.; Moraleda, J.; Quinones, D.

    2014-07-01

    Enusa and Tecnatom have embarked on a road of technological and commercial collaboration that aims to firstly, the continuous improvement of the means of production of fuel from the factory in Juzbado, but uses the joint technological capital to diversify their business global opportunities. This collaboration has emerged a new line for control by UT of welding circular fresh fuel rod and the development of an equipment for sale to the CINF in Yibin fuel factory. The characteristics of these projects are presented in this paper. (Author)

  12. Commissioning of a passive rod scanner at INB

    Energy Technology Data Exchange (ETDEWEB)

    Junqueira, Fabio da Silva; Oliveira, Carlos A.; Palheiros, Franklin, E-mail: carlossilva@inb.gov.br, E-mail: franklin@inb.gov.br [Industrias Nucleares do Brasil (INB), Resende, RJ (Brazil). Superintendencia de Engenharia do Combustivel; Fernandez, Pablo Jesus Piñer, E-mail: pineiro@tecnatom.es [Tecnatom, San Sebastian de los Reyes, Madrid (Spain)

    2015-07-01

    For the 21st reload for Angra 1, a shift from Standard to Advanced fuel design will be introduced, where the fuel assemblies under the new design will contain fuel rods with axial blanket, in line with ELETRONUCLEAR's requirement for a higher energy efficient reactor fuel. Additionally, fuel rods for Angra 2 and 3, using gadolinium type burnable poison, have to be submitted to inspections due to the demand for the same type of inspection, which cannot be certified at INB currently. In keeping with CNEN regulations, every fuel-assembly component must be inspected and certified by a qualified method. Nevertheless, INB lacks the means to perform the certification-required inspection aimed at determining the uranium enrichment and presence of gadolinium pellets inside the closed rods. Hence, the use is necessary of a scanner capable of inspecting differently enriched fuel rods and/or gadolinium pellets (axial blanket). This work aims to present the recent Passive Rod Scanner installed at INB with most advance technology in the area, making possible to completely fulfill Angra 1, 2 and 3 rods inspection at INB Resende site. (author)

  13. Evaluation of the internal pressure in UO{sub 2} and UO{sub 2}-Gd{sub 2}O{sub 3} rods of fuel assemblies 10 x 10 with the FEMAXI-Vi code; Evaluacion de la presion interna en barras de UO{sub 2} y UO{sub 2}-Gd{sub 2}O{sub 3} de ensambles combustibles 10 x 10 con el codigo FEMAXI-VI

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez L, H.; Lucatero, M. A., E-mail: hector.hernandez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2013-10-15

    Inside the acceptable criterions of fuel licensing are some that should be fulfilled in relation to the internal pressure of the fuel rods. These criterions are related with the loss of mechanical integrity due to the load excess in the pressure inside the jacket, as well as by the pressure that exercises the pellet on the jacket at the time of suffering the swelling by irradiation. This work shows the calculation of the increment of the internal pressure of the fuel rods caused by the swelling contribution of the pellets and by the accumulation of the fission gases inside the hole, pellet-jacket, in function of the burned for values of the lineal heat generation reason (LHGR) mean of fuel rods in arrangements 10 x 10. (author)

  14. Novel method for the measurement of liquid film thickness during fuel spray impingement on surfaces.

    Science.gov (United States)

    Henkel, S; Beyrau, F; Hardalupas, Y; Taylor, A M K P

    2016-02-01

    This paper describes the development and application of a novel optical technique for the measurement of liquid film thickness formed on surfaces during the impingement of automotive fuel sprays. The technique makes use of the change of the light scattering characteristics of a metal surface with known roughness, when liquid is deposited. Important advantages of the technique over previously established methods are the ability to measure the time-dependent spatial distribution of the liquid film without a need to add a fluorescent tracer to the liquid, while the measurement principle is not influenced by changes of the pressure and temperature of the liquid or the surrounding gas phase. Also, there is no need for non-fluorescing surrogate fuels. However, an in situ calibration of the dependence of signal intensity on liquid film thickness is required. The developed method can be applied to measure the time-dependent and two-dimensional distribution of the liquid fuel film thickness on the piston or the liner of gasoline direct injection (GDI) engines. The applicability of this technique was evaluated with impinging sprays of several linear alkanes and alcohols with different thermo-physical properties. The surface temperature of the impingement plate was controlled to simulate the range of piston surface temperatures inside a GDI engine. Two sets of liquid film thickness measurements were obtained. During the first set, the surface temperature of the plate was kept constant, while the spray of different fuels interacted with the surface. In the second set, the plate temperature was adjusted to match the boiling temperature of each fuel. In this way, the influence of the surface temperature on the liquid film created by the spray of different fuels and their evaporation characteristics could be demonstrated.

  15. Modeling and simulation performance of sucker rod beam pump

    Science.gov (United States)

    Aditsania, Annisa; Rahmawati, Silvy Dewi; Sukarno, Pudjo; Soewono, Edy

    2015-09-01

    Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

  16. Modeling and simulation performance of sucker rod beam pump

    Energy Technology Data Exchange (ETDEWEB)

    Aditsania, Annisa, E-mail: annisaaditsania@gmail.com [Department of Computational Sciences, Institut Teknologi Bandung (Indonesia); Rahmawati, Silvy Dewi, E-mail: silvyarahmawati@gmail.com; Sukarno, Pudjo, E-mail: psukarno@gmail.com [Department of Petroleum Engineering, Institut Teknologi Bandung (Indonesia); Soewono, Edy, E-mail: esoewono@math.itb.ac.id [Department of Mathematics, Institut Teknologi Bandung (Indonesia)

    2015-09-30

    Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

  17. Detecting the influence of fossil fuel and bio-fuel black carbon aerosols on near surface temperature changes

    Science.gov (United States)

    Jones, G. S.; Christidis, N.; Stott, P. A.

    2011-01-01

    Past research has shown that the dominant influence on recent global climate changes is from anthropogenic greenhouse gas increases with implications for future increases in global temperatures. One mitigation proposal is to reduce black carbon aerosol emissions. How much warming can be offset by controlling black carbon is unclear, especially as its influence on past climate has not been previously unambiguously detected. In this study observations of near-surface warming over the last century are compared with simulations using a climate model, HadGEM1. In the simulations black carbon, from fossil fuel and bio-fuel sources (fBC), produces a positive radiative forcing of about +0.25 Wm-2 over the 20th century, compared with +2.52 Wm-2 for well mixed greenhouse gases. A simulated warming of global mean near-surface temperatures over the twentieth century from fBC of 0.14 ± 0.1 K compares with 1.06 ± 0.07 K from greenhouse gases, -0.58 ± 0.10 K from anthropogenic aerosols, ozone and land use changes and 0.09 ± 0.09 K from natural influences. Using a detection and attribution methodology, the observed warming since 1900 has detectable influences from anthropogenic and natural factors. Fossil fuel and bio-fuel black carbon is found to have a detectable contribution to the warming over the last 50 yr of the 20th century, although the results are sensitive to the period being examined as fBC is not detected for the later fifty year period ending in 2006. The attributed warming of fBC was found to be consistent with the warming from fBC unscaled by the detection analysis. This study suggests that there is a possible significant influence from fBC on global temperatures, but its influence is small compared to that from greenhouse gas emissions.

  18. Regulatory perspective on incomplete control rod insertions

    Energy Technology Data Exchange (ETDEWEB)

    Chatterton, M.

    1997-01-01

    The incomplete control rod insertions experienced at South Texas Unit 1 and Wolf Creek are of safety concern to the NRC staff because they represent potential precursors to loss of shutdown margin. Even before it was determined if these events were caused by the control rods or by the fuel there was an apparent correlation of the problem with high burnup fuel. It was determined that there was also a correlation between high burnup and high drag forces as well as with rod drop time histories and lack of rod recoil. The NRC staff initial actions were aimed at getting a perspective on the magnitude of the problem as far as the number of plants and the amount of fuel that could be involved, as well as the safety significance in terms of shutdown margin. As tests have been performed and data has been analyzed the focus has shifted more toward understanding the problem and the ways to eliminate it. At this time the staff`s understanding of the phenomena is that it was a combination of factors including burnup, power history and temperature. The problem appears to be very sensitive to these factors, the interaction of which is not clearly understood. The model developed by Westinghouse provides a possible explanation but there is not sufficient data to establish confidence levels and sensitivity studies involving the key parameters have not been done. While several fixes to the problem have been discussed, no definitive fixes have been proposed. Without complete understanding of the phenomena, or fixes that clearly eliminate the problem the safety concern remains. The safety significance depends on the amount of shutdown margin lost due to incomplete insertion of the control rods. Were the control rods to stick high in the core, the reactor could not be shutdown by the control rods and other means such as emergency boration would be required.

  19. Investigation of control rod worth and nuclear end of life of BWR control rods

    Energy Technology Data Exchange (ETDEWEB)

    Magnusson, Per

    2008-01-15

    This work has investigated the Control Rod Worth (CRW) and Nuclear End of Life (NEOL) values for BWR control rods. A study of how different parameters affect NEOL was performed with the transport code PHOENIX4. It was found that NEOL, expressed in terms of {sup 10}B depletion, can be generalized beyond the conditions for which the rod is depleted, such as different power densities and void fractions, the corresponding variation in the NEOL will be about 0.2-0.4% {sup 10}B. It was also found that NEOL results for different fuel types and different fuel enrichments have a variation of about 2-3% in {sup 10}B depletion. A comparative study on NHOL and CRW was made between PHOENIX4 and the stochastic Monte Carlo code MCNP. It was found that there is a significant difference, both due to differences in the codes and to limitations in the geometrical modeling in PHOENIX4. Since MCNP is considered more physically correct, a methodology was developed to calculate the nuclear end of life of BWR control rods with MCNP. The advantages of the methodology are that it does not require other codes to perform the depletion of the absorber material, it can describe control rods of any design and it can deplete the control rod absorber material without burning the fuel. The disadvantage of the method is that is it time-consuming.

  20. Surface energy equation for heat transfer process in a pebble fuel

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa-Paredes, G., E-mail: gepe@xanum.uam.mx [Área de Ingeniería en Recursos Energéticos, Universidad Autónoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco 186 Col. Vicentina, México, DF 09340 (Mexico); Castillo-Jiménez, V. [Área de Ingeniería en Recursos Energéticos, Universidad Autónoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco 186 Col. Vicentina, México, DF 09340 (Mexico); Herranz-Puebla, L.E. [División de Fisión Nuclear, Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas, Avda. Complutense, 22, 28040 Madrid (Spain); Vázquez-Rodríguez, R. [Área de Ingeniería en Recursos Energéticos, Universidad Autónoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco 186 Col. Vicentina, México, DF 09340 (Mexico)

    2014-12-15

    Highlights: • Steady and transient behaviors of the interfacial heat transfer in a fuel element. • Non-local averaging volume method for deriving the surface energy equation. • The method captures significant physical phenomena of the interfacial heat transfer. • Closure relationships are proposed in order to obtain the temperatures distribution. • The derived average equation represents an upscaling regarding the local description. - Abstract: In this paper the surface energy equation for the heat transfer process (HT) between the mixture of fuel (TRISO particles and graphite matrix) and coating in a fuel pebble is derived. The fuel pebble can be treated as a heterogeneous region (mixture of microspheres and graphite) interacting thermally with the homogeneous region (the coating or cladding). These two regions are separated by a boundary region where the properties and behavior differ from those of the adjoining regions. The methodology applied for deriving the surface energy equation is based on the classical theory on interfacial transport phenomena. The surface energy equation derived in this work is an average equation that represents an upscaling respect to the local description. The regions around the surface where changes in the physical phenomena are important are of the order of microns, in contrast with interfacial mass transfer between phases that may be several molecular diameters. The numerical analysis regarding the application of surface energy equation is presented in this work.

  1. Rod internal pressure quantification and distribution analysis using Frapcon

    Energy Technology Data Exchange (ETDEWEB)

    Jessee, Matthew Anderson [ORNL; Wieselquist, William A [ORNL; Ivanov, Kostadin [Pennsylvania State University, University Park

    2015-09-01

    This report documents work performed supporting the Department of Energy (DOE) Office of Nuclear Energy (NE) Fuel Cycle Technologies Used Fuel Disposition Campaign (UFDC) under work breakdown structure element 1.02.08.10, ST Analysis. In particular, this report fulfills the M4 milestone M4FT- 15OR0810036, Quantify effects of power uncertainty on fuel assembly characteristics, within work package FT-15OR081003 ST Analysis-ORNL. This research was also supported by the Consortium for Advanced Simulation of Light Water Reactors (http://www.casl.gov), an Energy Innovation Hub (http://www.energy.gov/hubs) for Modeling and Simulation of Nuclear Reactors under U.S. Department of Energy Contract No. DE-AC05-00OR22725. The discharge rod internal pressure (RIP) and cladding hoop stress (CHS) distributions are quantified for Watts Bar Nuclear Unit 1 (WBN1) fuel rods by modeling core cycle design data, operation data (including modeling significant trips and downpowers), and as-built fuel enrichments and densities of each fuel rod in FRAPCON-3.5. A methodology is developed which tracks inter-cycle assembly movements and assembly batch fabrication information to build individual FRAPCON inputs for each evaluated WBN1 fuel rod. An alternate model for the amount of helium released from the zirconium diboride (ZrB2) integral fuel burnable absorber (IFBA) layer is derived and applied to FRAPCON output data to quantify the RIP and CHS for these types of fuel rods. SCALE/Polaris is used to quantify fuel rodspecific spectral quantities and the amount of gaseous fission products produced in the fuel for use in FRAPCON inputs. Fuel rods with ZrB2 IFBA layers (i.e., IFBA rods) are determined to have RIP predictions that are elevated when compared to fuel rod without IFBA layers (i.e., standard rods) despite the fact that IFBA rods often have reduced fill pressures and annular fuel pellets. The primary contributor to elevated RIP predictions at burnups less than and greater than 30 GWd

  2. Eulerian Formulation of Spatially Constrained Elastic Rods

    Science.gov (United States)

    Huynen, Alexandre

    Slender elastic rods are ubiquitous in nature and technology. For a vast majority of applications, the rod deflection is restricted by an external constraint and a significant part of the elastic body is in contact with a stiff constraining surface. The research work presented in this doctoral dissertation formulates a computational model for the solution of elastic rods constrained inside or around frictionless tube-like surfaces. The segmentation strategy adopted to cope with this complex class of problems consists in sequencing the global problem into, comparatively simpler, elementary problems either in continuous contact with the constraint or contact-free between their extremities. Within the conventional Lagrangian formulation of elastic rods, this approach is however associated with two major drawbacks. First, the boundary conditions specifying the locations of the rod centerline at both extremities of each elementary problem lead to the establishment of isoperimetric constraints, i.e., integral constraints on the unknown length of the rod. Second, the assessment of the unilateral contact condition requires, in principle, the comparison of two curves parametrized by distinct curvilinear coordinates, viz. the rod centerline and the constraint axis. Both conspire to burden the computations associated with the method. To streamline the solution along the elementary problems and rationalize the assessment of the unilateral contact condition, the rod governing equations are reformulated within the Eulerian framework of the constraint. The methodical exploration of both types of elementary problems leads to specific formulations of the rod governing equations that stress the profound connection between the mechanics of the rod and the geometry of the constraint surface. The proposed Eulerian reformulation, which restates the rod local equilibrium in terms of the curvilinear coordinate associated with the constraint axis, describes the rod deformed configuration

  3. Reliability Analysis of Propagation Lives of Sucker Rod's Surface Crack%抽油杆表面裂纹扩展寿命可靠性分析

    Institute of Scientific and Technical Information of China (English)

    李鹤; 马铭蔚; 陶婷; 闻邦椿

    2012-01-01

    The crack propagation life was calculated under the tensile load using the sectional type numerical integration method based on the Paris formula considering the relation of geometric modified index f and crack size a. The Monte Carlo method was also used to get the reliability of different types of surface crack propagation lives. The results showed that taking the defect as an elliptical crack governed by depth ration and aspect ratio is better than circular arc crack or straight-edged crack only governed by depth ration. The sucker rods with the circular crack break first. The critical crack propagation life based on the traditional fracture mechanics is not accurate, and the sucker rod may break before the critical crack propagation lives.%在拉伸载荷的作用下,以Paris公式为基础,考虑几何修正系数f与裂纹尺寸α的内在关系,结合分段数值积分方法计算抽油杆裂纹扩展寿命,并应用MonteCarlo法计算不同类型表面裂纹扩展寿命可靠度.计算结果表明,在其他条件相同情况下,把裂纹处理为受深度比、纵横比两个参数控制的椭圆裂纹比仅受深度比控制的圆弧裂纹和直裂纹适应性更强;带有环形裂纹的抽油杆最先断裂;断裂力学中将各个参数作为确定值计算得到的临界裂纹扩展寿命不够准确,可能导致部分抽油杆还未达到临界裂纹扩展寿命就发生断裂.

  4. CRITICAL CONFIGURATION FOR BERYLLIUM REFLECTED ASSEMBLIES OF U(93.15)O2 FUEL RODS (1.506-CM PITCH AND 7-TUBE CLUSTERS)

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2012-05-01

    A series of critical experiments were completed in 1962-1965 at Oak Ridge National Laboratory’s Critical Experiments Facility in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950’s efforts were made to study “power plants for the production of electrical power in space vehicles”. The MPRE program was a part of those efforts and studied the feasibility of a stainless steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967. The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of 253 unmoderated stainless steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were made to determine critical reflector arrangements, fission-rate distributions, and cadmium ratio distributions. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector.” The first two experiments in the series were evaluated in HEU-COMP-FAST-001 (SCCA-FUND-EXP-001) and HEU-COMP-FAST-002 (SCCA-FUND-EXP-002). The first experiment had the 253 fuel tubes packed tightly into a 22.87 cm outside diameter (OD) core tank (References 1 and 2). The second experiment in the series, performed in early 1963, had the 253 fuel tubes at a 1.506-cm triangular lattice in a 25.96 cm OD core tank and graphite reflectors on all sides. The third set of experiments in the series, performed in mid-1963, which is studied in this evaluation, used beryllium reflectors. The beryllium reflected system was the preferred reactor configuration for this application because of the small thickness of the reflector. The two core configurations had the 253 fuel tubes

  5. Telescopic drilling rod

    Energy Technology Data Exchange (ETDEWEB)

    Kagan, I.L.; Berezov, S.I.; Gavrilov, G.A.; Goykhman, Ya.A.; Makushkin, D.O.; Rachev, M.P.; Voynich, L.K.

    1981-09-07

    The telescopic drilling rod includes an inner section of the rod, in whose center cable has been passed and is attached a bearing assembly connecting it to the winch, outer section of rod along which there is pipeline connecting the working cavity formed by the inner section of rod and the housing, installed on the lower end of the outer section of rod, with cavity formed by framework of the guide swivel and end piece and connected to the hydraulic system of the machine by pipeline, as well as clamping elements. In order to drill wells to a depth greater than the length of the outer sectrion of the rod, the latter jointly with the inner section of rod is lowered into the extreme lower position until swivel rests on the feed mechanism. With further slipping of cable and the absence of pressure in the hydraulic system, clamping elements do not have an effect on the inner section of rod. It has the opportunity to freely move along the outer section of rod downwards to the face. When pressure is supplied on pipeline into cavity and further through pipeline into working cavity, the inner section of rod is clamped with feed of the outer section in the process of drilling, both sections move jointly. Because of the link between working cavity of sleeve installed on the lower end of the outer section of rod, and the hydraulic system of the machine through the swivel cavity, it is possible to fix the drilling rod in any mutual axial position of the section.

  6. High-Level Systemic Expression of Conserved Influenza Epitope in Plants on the Surface of Rod-Shaped Chimeric Particles

    Directory of Open Access Journals (Sweden)

    Natalia V. Petukhova

    2014-04-01

    Full Text Available Recombinant viruses based on the cDNA copy of the tobacco mosaic virus (TMV genome carrying different versions of the conserved M2e epitope from influenza virus A cloned into the coat protein (CP gene were obtained and partially characterized by our group previously; cysteines in the human consensus M2e sequence were changed to serine residues. This work intends to show some biological properties of these viruses following plant infections. Agroinfiltration experiments on Nicotiana benthamiana confirmed the efficient systemic expression of M2e peptides, and two point amino acid substitutions in recombinant CPs significantly influenced the symptoms and development of viral infections. Joint expression of RNA interference suppressor protein p19 from tomato bushy stunt virus (TBSV did not affect the accumulation of CP-M2e-ser recombinant protein in non-inoculated leaves. RT-PCR analysis of RNA isolated from either infected leaves or purified TMV-M2e particles proved the genetic stability of TMV‑based viral vectors. Immunoelectron microscopy of crude plant extracts demonstrated that foreign epitopes are located on the surface of chimeric virions. The rod‑shaped geometry of plant-produced M2e epitopes is different from the icosahedral or helical filamentous arrangement of M2e antigens on the carrier virus-like particles (VLP described earlier. Thereby, we created a simple and efficient system that employs agrobacteria and plant viral vectors in order to produce a candidate broad-spectrum flu vaccine.

  7. Near-surface alloys for hydrogen fuel cell applications

    DEFF Research Database (Denmark)

    Greeley, Jeffrey Philip; Mavrikakis, Manos

    2006-01-01

    Near-surface alloys (NSAs) possess a variety of unusual catalytic properties that could make them useful candidates for improved catalysts in a variety of chemical processes. It is known from previous work, for example, that some NSAs bind hydrogen very weakly while, at the same time, permitting ...

  8. Analysis of heterogeneous oxygen exchange and fuel oxidation on the catalytic surface of perovskite membranes

    KAUST Repository

    Hong, Jongsup

    2013-10-01

    The catalytic kinetics of oxygen surface exchange and fuel oxidation for a perovskite membrane is investigated in terms of the thermodynamic state in the immediate vicinity of or on the membrane surface. Perovskite membranes have been shown to exhibit both oxygen perm-selectivity and catalytic activity for hydrocarbon conversion. A fundamental description of their catalytic surface reactions is needed. In this study, we infer the kinetic parameters for heterogeneous oxygen surface exchange and catalytic fuel conversion reactions, based on permeation rate measurements and a spatially resolved physical model that incorporates detailed chemical kinetics and transport in the gas-phase. The conservation equations for surface and bulk species are coupled with those of the gas-phase species through the species production rates from surface reactions. It is shown that oxygen surface exchange is limited by dissociative/associative adsorption/desorption of oxygen molecules onto/from the membrane surface. On the sweep side, while the catalytic conversion of methane to methyl radical governs the overall surface reactions at high temperature, carbon monoxide oxidation on the membrane surface is dominant at low temperature. Given the sweep side conditions considered in ITM reactor experiments, gas-phase reactions also play an important role, indicating the significance of investigating both homogeneous and heterogeneous chemistry and their coupling when examining the results. We show that the local thermodynamic state at the membrane surface should be considered when constructing and examining models of oxygen permeation and heterogeneous chemistry. © 2013 Elsevier B.V.

  9. Quantitative Surface Emissivity and Temperature Measurements of a Burning Solid Fuel Accompanied by Soot Formation

    Science.gov (United States)

    Piltch, Nancy D.; Pettegrew, Richard D.; Ferkul, Paul; Sacksteder, K. (Technical Monitor)

    2001-01-01

    Surface radiometry is an established technique for noncontact temperature measurement of solids. We adapt this technique to the study of solid surface combustion where the solid fuel undergoes physical and chemical changes as pyrolysis proceeds, and additionally may produce soot. The physical and chemical changes alter the fuel surface emissivity, and soot contributes to the infrared signature in the same spectral band as the signal of interest. We have developed a measurement that isolates the fuel's surface emissions in the presence of soot, and determine the surface emissivity as a function of temperature. A commercially available infrared camera images the two-dimensional surface of ashless filter paper burning in concurrent flow. The camera is sensitive in the 2 to 5 gm band, but spectrally filtered to reduce the interference from hot gas phase combustion products. Results show a strong functional dependence of emissivity on temperature, attributed to the combined effects of thermal and oxidative processes. Using the measured emissivity, radiance measurements from several burning samples were corrected for the presence of soot and for changes in emissivity, to yield quantitative surface temperature measurements. Ultimately the results will be used to develop a full-field, non-contact temperature measurement that will be used in spacebased combustion investigations.

  10. Changes of surface structure and elemental composition of components of deuterium high-pressure chamber with Pd rod inside irradiated with 10-MeV γ-quanta in dense deuterium gas

    Science.gov (United States)

    Didyk, A. Yu.; Wiśniewski, R.; Wilczynska-Kitowska, T.

    2013-12-01

    This work is a continuation and addition to Ref. [1], which presents results on studies of the surface and elemental compositions of a Pd rod and brass screw for the collection of nuclear and chemical reaction products in a deuterium high-pressure chamber (DHPC) under irradiation with γ-quanta with an energy of 10 MeV for 18 h at the MT-25 electron accelerator at a beam current of 11-13 μA. The DHPC is filled with 1.2-kbar molecular deuterium in which a Pd rod saturated with deuterium is loaded. After irradiation, the elemental compositions of other surfaces of all DHPC elements, which are inside the DHPC in dense deuterium, are studied using an electron scanning microscope and X-ray microprobe analysis. It is established that all surfaces, including the surface of a high-purity palladium rod (99.995%), are covered with a partly homogeneous layer of large microparticles of lead. Also, light elements such as 6C, 8O, 11Na, 12Mg, 13Al, 14Si, 22Ti, 25Mn, 26Fe, 29Cu, and 30Zn and heavy metals such as 47Ag, 73Ta, 74W, 78Pt, 79Au, and 82Pb are observed. Possible processes that can cause the anomalies observed in the new synthesized elements are briefly discussed.

  11. Optimization of Microstructure of Oxidized Scales on Surface of Hot Rolled Wire Rods for Welding%焊接用热轧盘条表面氧化铁皮结构优化

    Institute of Scientific and Technical Information of China (English)

    吕建勋; 蒋艳菊; 邓国光; 朱江

    2016-01-01

    本溪钢铁集团北营公司生产的H08A盘条所制焊条在下游客户使用过程中,出现焊接烟尘量较大问题。检测分析结果表明,盘条母材表面氧化铁皮结构异常是导致焊接烟尘量大的主要原因。通过优化轧制工艺,调节盘条冷却温度及冷却速度,加快盘条在900~800益区间及600~450益区间的冷却速度,在不影响盘条正常组织的前提下,合理改善表面氧化铁皮结构,消除内层Fe3O4,增大FeO比例,降低焊条使用时的焊接烟尘量,改善了焊接作业环境。%There was the problem that heavy weld fumes occurred in welding by downstream customers when using welding rods made by H08A wire rods produced by Beiying Company of Benxi Iron & Steel Group Corporation. According to the analytical results by detection, the abnormal microstructure of the oxidized scales on the surface of the base wire rods was the major cause leading to heavy weld fumes. So some corresponding measures was taken, which includes adjusting the cooling temperature and cooling velocity for wire rods, increasing the cooling velocity for wire rods between 800℃ and 900 ℃and between 450℃ and 600 ℃by optimizing the rolling process and suitably improving the microstructure of the oxidized scales on the surface of wire rods to eliminate the intimal Fe3O4 and increase the proportion of FeO providing that the normal microstructure of wire rods was not influenced. As a result, the amount of weld fumes was decreased and the working environment was improved.

  12. Radiochemical analyses of several spent fuel Approved Testing Materials

    Energy Technology Data Exchange (ETDEWEB)

    Guenther, R.J.; Blahnik, D.E.; Wildung, N.J.

    1994-09-01

    Radiochemical characterization data are described for UO{sub 2} and UO{sub 2} plus 3 wt% Gd{sub 2}O{sub 3} commercial spent nuclear fuel taken from a series of Approved Testing Materials (ATMs). These full-length nuclear fuel rods include MLA091 of ATM-103, MKP070 of ATM-104, NBD095 and NBD131 of ATM-106, and ADN0206 of ATM-108. ATMs 103, 104, and 106 were all irradiated in the Calvert Cliffs Nuclear Power Plant (Reactor No.1), a pressurized-water reactor that used fuel fabricated by Combustion Engineering. ATM-108 was part of the same fuel bundle designed as ATM-105 and came from boiling-water reactor fuel fabricated by General Electric and irradiated in the Cooper Nuclear Power Plant. Rod average burnups and expected fission gas releases ranged from 2,400 to 3,700 GJ/kgM. (25 to 40 Mwd/kgM) and from less than 1% to greater than 10%, respectively, depending on the specific ATM. The radiochemical analyses included uranium and plutonium isotopes in the fuel, selected fission products in the fuel, fuel burnup, cesium and iodine on the inner surfaces of the cladding, {sup 14}C in the fuel and cladding, and analyses of the gases released to the rod plenum. Supporting examinations such as fuel rod design and material descriptions, power histories, and gamma scans used for sectioning diagrams are also included. These ATMs were examined as part of the Materials Characterization Center Program conducted at Pacific Northwest Laboratory provide a source of well-characterized spent fuel for testing in support of the US Department of Energy Office of Civilian Radioactive Waste Management Program.

  13. Critique of Sikkink and Keane's comparison of surface fuel sampling techniques

    Science.gov (United States)

    Clinton S. Wright; Roger D. Ottmar; Robert E. Vihnanek

    2010-01-01

    The 2008 paper of Sikkink and Keane compared several methods to estimate surface fuel loading in western Montana: two widely used inventory techniques (planar intersect and fixed-area plot) and three methods that employ photographs as visual guides (photo load, photoload macroplot and photo series). We feel, however, that their study design was inadequate to evaluate...

  14. Handbook for inventorying surface fuels and biomass in the Interior West

    Science.gov (United States)

    James K. Brown; Rick D. Oberheu; Cameron M. Johnston

    1982-01-01

    Presents comprehensive procedures for inventorying weight per unit area of living and dead surface vegetation, to facilitate estimation of biomass and appraisal of fuels. Provides instructions for conducting fieldwork and calculating estimates of downed woody material, forest floor litter and duff, herbaceous vegetation, shrubs, and small conifers. Procedures produce...

  15. CRITICAL CONFIGURATION AND PHYSICS MEASUREMENTS FOR GRAPHITE REFLECTED ASSEMBLIES OF U(93.15)O2 FUEL RODS (1.506-CM PITCH)

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2012-03-01

    A series of critical experiments were completed in 1962-1965 at Oak Ridge National Laboratory’s Critical Experiments Facility in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950’s efforts were made to study “power plants for the production of electrical power in space vehicles”. The MPRE program was a part of those efforts and studied the feasibility of a stainless steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967. The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of 253 unmoderated stainless steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were made to determine critical reflector arrangements, fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector.” The first experiment in the series was evaluated in HEU-COMP-FAST-001. It had the 253 fuel tubes packed tightly into a 22.87 cm outside diameter (OD) core tank (References 1 and 2). The second experiment in the series, performed in early 1963, which is studied in this evaluation, had the 253 fuel tubes at a 1.506-cm triangular lattice in a 25.96 cm OD core tank and graphite reflectors on all sides. The experiment has been determined to represent an acceptable benchmark experiment. Information for this evaluation was compiled from published reports on all three parts of the experimental series (Reference 1-5) and the experimental logbook as

  16. Evaporation of hydrocarbon compounds, including gasoline and diesel fuel, on heated metal surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Fardad, D.; Ladommatos, N. [Brunel Univ., Dept. of Mechanical Engineering, Uxbridge (United Kingdom)

    1999-11-01

    An investigation was carried out on the evaporation of various hydrocarbon liquids on heated surfaces. Single and multicomponent hydrocarbon compounds were used, including hexane, heptane, octane, a hexane-octane mixture, gasoline and diesel fuel. The heated surface included aluminium, mild steel, cast iron and copper. Tests were also carried out with different surface textures and surface coatings. The motivation for this work was a desire to improve understanding of the evaporation processes taking place in the inlet port and, to a lesser extent, within the combustion chamber of internal combustion engines. The hydrocarbon compounds were released on the heated surfaces as individual small droplets, and the subsequent evaporation was recorded using a CCD (charge coupled device) camera. These observations were then used to ascertain the effects of material, surface temperature, surface textures, surface coating and liquid composition on the heat flux and other aspects of droplet behaviour. (Author)

  17. High Performance Fuel Desing for Next Generation Pressurized Water Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Mujid S. Kazimi; Pavel Hejzlar

    2006-01-31

    The use of internally and externally cooled annular fule rods for high power density Pressurized Water Reactors is assessed. The assessment included steady state and transient thermal conditions, neutronic and fuel management requirements, mechanical vibration issues, fuel performance issues, fuel fabrication methods and econmic assessment. The investigation was donducted by a team from MIT, Westinghouse, Gamma Engineering, Framatome ANP, and AECL. The analyses led to the conclusion that raising the power density by 50% may be possible with this advanced fuel. Even at the 150% power level, the fuel temperature would be a few hundred degrees lower than the current fuel temperatre. Significant economic and safety advantages can be obtained by using this fuel in new reactors. Switching to this type of fuel for existing reactors would yield safety advantages, but the economic return is dependent on the duration of plant shutdown to accommodate higher power production. The main feasiblity issue for the high power performance appears to be the potential for uneven splitting of heat flux between the inner and outer fuel surfaces due to premature closure of the outer fuel-cladding gap. This could be overcome by using a very narrow gap for the inner fuel surface and/or the spraying of a crushable zirconium oxide film at the fuel pellet outer surface. An alternative fuel manufacturing approach using vobropacking was also investigated but appears to yield lower than desirable fuel density.

  18. Experimental data report for test TS-4, Reactivity initiated accident test in the NSRR with pre-irradiated BWR fuel rod

    OpenAIRE

    1994-01-01

    本報告書は1991年1月に実施した照射済BWR燃料を用いた4回目の反応度事故模擬実験であるTS-4について、実験データをまとめたものである。TS-4実験に使用した試験燃料は、初期濃縮度2.79%であり、日本原子力発電(株)の敦賀1号炉で照射されたBWR7times7型燃料棒を短尺化したものである。短尺化に供した燃料の燃焼度は26GWd/tUであった。NSRRにおける照射実験は、BWRのコールドスタートアップ条件を模擬した大気圧・室温の静止水冷却条件下で行い、公称発熱量は110pm5cal/g・fuel(ピークエンタルピ89pm4cal/g・fuel)を与えた。その結果、燃料破損は生じなかった。実験条件、実験方法、パルス照射時の燃料の過渡挙動及び照射後検査の結果をまとめて示した。...

  19. Experimental data report for test TS-3; Reactivity initiated accident test in the NSRR with pre-irradiated BWR fuel rod

    OpenAIRE

    1993-01-01

    本報告書は、1990年9月に実施した照射済BWR燃料を用いた3回目の反応度事故模擬実験であるTS-3について実験データをまとめたものである。TS-3実験に使用した試験燃料は初期濃縮度2.79%であり、敦賀1号炉で照射されたBWR7times7型燃料棒を短尺化したものである。短尺化に供した実用燃料のバンドル平均燃焼度は21.3GWd/tUであった。NSRRにおける照射実験は、大気圧・室温の静止水冷却条件下で行い、発熱量は94pm4cal/g・fuel(ピークエンタルピ88pm4cal/g・fuel)を与えた。その結果燃料破損は生じなかった。実験条件、実験方法、パルス照射時の燃料の過渡挙動及び照射後検査の結果をまとめて示した。...

  20. Critical Configuration and Physics Mesaurements for Graphite Reflected Assemblies of U(93.15)O2 Fuel Rods (1.27-CM Pitch)

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2011-09-01

    A series of critical experiments were completed in 1962-1965 at Oak Ridge National Laboratory's Critical Experiments Facility in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950's efforts were made to study 'power plants for the production of electrical power in space vehicles'. The MPRE program was a part of those efforts and studied the feasibility of a stainless steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in FY 1964, 1965, and 1966. A summary of the program's effort was compiled in 1967. The delayed critical experiments served as a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of unmoderated 253 stainless steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were made to determine critical reflector arrangements, fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. 'The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector.' The experiment studied within this evaluation was the first of the series and had the 253 fuel tubes packed tightly into a 22.87 cm outside diameter (OD) core tank. Two critical configurations were found by varying the amount of graphite reflector (References 1 and 2). Information for this evaluation was compiled from Reference 1 and 2, reports on subsequent experiments in the series, and the experimental logbook as well as from communication with the experimenter, John T. Mihalczo.

  1. Detecting the influence of fossil fuel and bio-fuel black carbon aerosols on near surface temperature changes

    Directory of Open Access Journals (Sweden)

    G. S. Jones

    2010-09-01

    Full Text Available Past research has shown that the dominant influence on recent global climate changes is from anthropogenic greenhouse gas increases with implications for future increases in global temperatures. One mitigation proposal is to reduce black carbon aerosol emissions. How much warming can be offset by the aerosol's control is unclear, especially as its influence on past climate has not been previously unambiguously detected. In this study observations of near-surface warming over the last century are compared with simulations using a climate model, HadGEM1. In the simulations black carbon, from fossil fuel and bio-fuel sources (fBC, produces a positive radiative forcing of about + 0.25 Wm−2 over the 20th century, compared with a little under + 2.5 Wm−2 for well mixed greenhouse gases. A simulated warming of global mean near-surface temperatures over the twentieth century from fBC of 0.14 ± 0.1 K compares with 1.06 ± 0.07 K from greenhouse gases, -0.58 ± 0.10 K from anthropogenic aerosols, ozone and land use changes and 0.09 ± 0.09 K from natural influences. Using a detection and attribution methodology, the observed warming since 1900 has detectable influences from anthropogenic and natural factors. Fossil fuel and bio-fuel black carbon is found to have a detectable contribution to the warming over the last 50 years of the 20th century, although the results are sensitive to a number of analysis choices, and fBC is not detected for the later fifty year period ending in 2006. The attributed warming of fBC was found to be consistent with the warming from the unscaled simulation. This study suggests that there is a possible significant influence from fBC on global temperatures, but its influence is small compared to that from greenhouse gas emissions.

  2. Detecting the influence of fossil fuel and bio-fuel black carbon aerosols on near surface temperature changes

    Directory of Open Access Journals (Sweden)

    G. S. Jones

    2011-01-01

    Full Text Available Past research has shown that the dominant influence on recent global climate changes is from anthropogenic greenhouse gas increases with implications for future increases in global temperatures. One mitigation proposal is to reduce black carbon aerosol emissions. How much warming can be offset by controlling black carbon is unclear, especially as its influence on past climate has not been previously unambiguously detected. In this study observations of near-surface warming over the last century are compared with simulations using a climate model, HadGEM1. In the simulations black carbon, from fossil fuel and bio-fuel sources (fBC, produces a positive radiative forcing of about +0.25 Wm−2 over the 20th century, compared with +2.52 Wm−2 for well mixed greenhouse gases. A simulated warming of global mean near-surface temperatures over the twentieth century from fBC of 0.14 ± 0.1 K compares with 1.06 ± 0.07 K from greenhouse gases, −0.58 ± 0.10 K from anthropogenic aerosols, ozone and land use changes and 0.09 ± 0.09 K from natural influences. Using a detection and attribution methodology, the observed warming since 1900 has detectable influences from anthropogenic and natural factors. Fossil fuel and bio-fuel black carbon is found to have a detectable contribution to the warming over the last 50 yr of the 20th century, although the results are sensitive to the period being examined as fBC is not detected for the later fifty year period ending in 2006. The attributed warming of fBC was found to be consistent with the warming from fBC unscaled by the detection analysis. This study suggests that there is a possible significant influence from fBC on global temperatures, but its influence is small compared to that from greenhouse gas emissions.

  3. Vibration of the Package of Rods Linked by Spacer Grids

    Science.gov (United States)

    Zeman, V.; Hlaváč, Z.

    This paper deals with modelling and vibration analysis of the large package of identical parallel rods which are linked by transverse springs (spacer grids) placed on several level spacings. The vibration of rods is caused by the support plate motion. The rod discretization by FEM is based on Rayleigh beam theory. With respect to cyclic and central package rod symmetry, the system is decomposed to identical revolved rod segments. The modal synthesis method with condensation of the rod segments is used for modelling and determination of steady forced vibration of the whole system. The presented method is the first step to modelling of the nuclear fuel assembly vibration caused by kinematical excitation determined by motion of the support plates which are part of the reactor core.

  4. Investigation of axial power gradients near a control rod tip

    Energy Technology Data Exchange (ETDEWEB)

    Loberg, John, E-mail: John.Loberg@fysast.uu.se [Uppsala University, Department of Physics and Astronomy, Division of Applied Nuclear Physics, Box 525, SE-75120 Uppsala (Sweden); Osterlund, Michael, E-mail: Michael.Osterlund@fysast.uu.se [Uppsala University, Department of Physics and Astronomy, Division of Applied Nuclear Physics, Box 525, SE-75120 Uppsala (Sweden); Bejmer, Klaes-Hakan, E-mail: Klaes-Hakan.Bejmer@vattenfall.com [Vattenfall Nuclear Fuel AB, Jaemtlandsgatan 99, 162 60 Vaellingby, Stockholm (Sweden); Blomgren, Jan, E-mail: Jan.Blomgren@vattenfall.com [Vattenfall Nuclear Fuel AB, Jaemtlandsgatan 99, 162 60 Vaellingby, Stockholm (Sweden); Kierkegaard, Jesper, E-mail: Jesper.Kierkegaar@vattenfall.com [Vattenfall Nuclear Fuel AB, Jaemtlandsgatan 99, 162 60 Vaellingby, Stockholm (Sweden)

    2011-07-15

    Highlights: > Pin power gradients near BWR control rod tips have been investigated. > A control rod tip is modeled in MCNP and compared to simplified 2D/3D geometry. > Small nodes increases pin power gradients; standard nodes underestimates gradients. > The MCNP results are validated against axial gamma scan of a controlled fuel pin. - Abstract: Control rod withdrawal in BWRs induces large power steps in the adjacent fuel assemblies. This paper investigates how well a 2D/3D method, e.g., CASMO5/SIMULATE5 computes axial pin power gradients adjacent to an asymmetrical control-rod tip in a BWR. The ability to predict pin power gradients accurately is important for safety considerations whereas large powers steps induced by control rod withdrawal can cause Pellet Cladding Interaction. The computation of axial pin power gradients axially around a control rod tip is a challenging task for any nodal code. On top of that, asymmetrical control rod handles are present in some BWR designs. The lattice code CASMO requires diagonal symmetry of all control rod parts. This introduces an error in computed pin power gradients that has been evaluated by Monte Carlo calculations. The results show that CASMO5/SIMULATE5, despite the asymmetrical control rod handle, is able to predict the axial pin power gradient within 1%/cm for axial nodal sizes of 15-3.68 cm. However, a nodal size of 3.68 cm still causes underestimations of pin power gradients compared with 1 cm nodes. Furthermore, if conventional node sizes are used, {approx}15 cm, pin power gradients can be underestimated by over 50% compared with 1 cm nodes. The detailed axial pin power profiles from MCNP are corroborated by measured gamma scan data on fuel rods irradiated adjacent to control rods.

  5. Lithium and boron analysis by LA-ICP-MS results from a bowed PWR rod with contact

    Directory of Open Access Journals (Sweden)

    Puranen Anders

    2017-01-01

    Full Text Available A previously published investigation of an irradiated fuel rod from the Ringhals 2 PWR, which was bowed to contact with an adjacent rod, identified a significant but highly localised thinning of the clad wall and increased corrosion. Rod fretting was deemed unlikely due to the adhering oxide covering the surfaces. Local overheating in itself was also deemed insufficient to account for the accelerated corrosion. Instead, an enhanced concentration of lithium due to conditions of local boiling was hypothesised to explain the accelerated corrosion. Studsvik has developed a hot cell coupled LA-ICP-MS (Laser Ablation Inductively Coupled Plasma Mass Spectrometer equipment that enables a flexible means of isotopic analysis of irradiated fuel and other highly active surfaces. In this work, the equipment was used to investigate the distribution of lithium (7Li and boron (11B in the outer oxide at the bow contact area. Depth profiling in the clad oxide at the opposite side of the rod to the point of contact, which is considered to have experienced normal operating conditions and which has a typical oxide thickness, evidenced levels of ∼10–20 ppm 7Li and a 11B content reaching hundreds of ppm in the outer parts of the oxide, largely in agreement with the expected range of Li and B clad oxide concentrations from previous studies. In the contact area, the 11B content was similar to the reference condition at the opposite side. The 7Li content in the outermost oxide closest to the contact was, however, found to be strongly elevated, reaching several hundred ppm. The considerable and highly localised increase in lithium content at the area of enhanced corrosion thus offers strong evidence for a case of lithium induced breakaway corrosion during power operation, when rod-to-rod contact and high enough surface heat flux results in a very local increase in lithium concentration.

  6. CRITICAL CONFIGURATION AND PHYSICS MEASUREMENTS FOR BERYLLIUM REFLECTED ASSEMBLIES OF U(93.15)O2 FUEL RODS (1.506-CM PITCH AND 7-TUBE CLUSTERS)

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2014-03-01

    Cadmium ratios were measured with enriched uranium metal foils at various locations in the assembly with the fuel tube at the 1.506-cm spacing. They are described in the following subsections. The experiment configuration was the same as the first critical configuration described in HEU-COMP-FAST-004 (Case 1). The experimenter placed 0.75-cm-diameter × 0.010-cm-thick 93.15%-235U-enriched uranium metal foils with and without 0.051-cm-thick cadmium covers at various locations in the core and top reflector. One part of the cadmium cover was cupshape and contained the uranium foil. The other part was a lid that fit over the exposed side of the foil when it was in the cup shaped section of the cover. As can be seen in the logbook, two runs were required to obtain all the measurements necessary for the cadmium ratio. The bare foil measurements within the top reflector were run first as part of the axial foil activation measurements. The results of this run are used for both the axial activation results and the cadmium ratios. Cadmium covered foils were then placed at the same location through the top reflector in a different run. Three pairs of bare and cadmium covered foils were also placed through the core tank. One pair was placed at the axial center of a fuel tube 11.35 cm from the center of the core. Two pairs of foils were placed on top of fuel tubes 3.02 and 12.06 cm from the center of the core. The activation of the uranium metal foils was measured after removal from the assembly using two lead shielded NaI scintillation detectors as follows. The NaI scintillators were carefully matched and had detection efficiencies for counting delayed-fission-product gamma rays with energies above 250 KeV within 5%. In all foil activation measurements, one foil at a specific location was used as a normalizing foil to remove the effects of the decay of fission products during the counting measurements with the NaI detectors. The normalization foil was placed on one Na

  7. Critical Configuration and Physics Measurements for Beryllium Reflected Assemblies of U(93.15)O₂ Fuel Rods (1.506-cm Pitch and 7-Tube Clusters)

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, Margaret A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bess, John D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Briggs, J. Blair [Idaho National Lab. (INL), Idaho Falls, ID (United States); Murphy, Michael F. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mihalczo, John T. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-03-01

    Cadmium ratios were measured with enriched uranium metal foils at various locations in the assembly with the fuel tube at the 1.506-cm spacing. They are described in the following subsections. The experiment configuration was the same as the first critical configuration described in HEU-COMP-FAST-004 (Case 1). The experimenter placed 0.75-cm-diameter × 0.010-cm-thick 93.15%-235U-enriched uranium metal foils with and without 0.051-cm-thick cadmium covers at various locations in the core and top reflector. One part of the cadmium cover was cupshape and contained the uranium foil. The other part was a lid that fit over the exposed side of the foil when it was in the cup shaped section of the cover. As can be seen in the logbook, two runs were required to obtain all the measurements necessary for the cadmium ratio. The bare foil measurements within the top reflector were run first as part of the axial foil activation measurements. The results of this run are used for both the axial activation results and the cadmium ratios. Cadmium covered foils were then placed at the same location through the top reflector in a different run. Three pairs of bare and cadmium covered foils were also placed through the core tank. One pair was placed at the axial center of a fuel tube 11.35 cm from the center of the core. Two pairs of foils were placed on top of fuel tubes 3.02 and 12.06 cm from the center of the core. The activation of the uranium metal foils was measured after removal from the assembly using two lead shielded NaI scintillation detectors as follows. The NaI scintillators were carefully matched and had detection efficiencies for counting delayed-fission-product gamma rays with energies above 250 KeV within 5%. In all foil activation measurements, one foil at a specific location was used as a normalizing foil to remove the effects of the decay of fission products during the counting measurements with the NaI detectors. The normalization foil was placed on one Na

  8. Sintering of CaF 2 pellets as nuclear fuel analog for surface stability experiments

    Science.gov (United States)

    Godinho, José R. A.; Piazolo, Sandra; Stennett, Martin C.; Hyatt, Neil C.

    2011-12-01

    To enable a detailed study of the influence of microstructure and surface properties on the stability of spent nuclear fuel, it is necessary to produce analogs that closely resemble nuclear fuel in terms of crystallography and microstructure. One such analog can be obtained by sintering CaF 2 powder. This paper reports the microstructures obtained after sintering CaF 2 powders at temperatures up to 1240 °C. Pellets with microstructure, density and pore structure similar to that of UO 2 spent nuclear fuel pellets were obtained in the temperature range between 900 °C and 1000 °C. When CaF 2 was sintered above 1100 °C the formation of CaO at the grain boundaries caused the disintegration of the pellet due to hydration occurring after sintering. First results from a novel set-up of dissolution experiments show that changes in roughness, dissolution rate and etch pit shape of fluorite surfaces are strongly dependent on the crystallographic orientation of the expose surface. Consequently, the differences observed for each orientation will affect the overall dissolution rate and will lead to uncertainties in the estimation of dissolution rates of spent nuclear fuel.

  9. Experimental data report for test TS-5; Reactivity initiated accident test in the NSRR with pre-irradiated BWR fuel rod

    OpenAIRE

    1995-01-01

    本報告書は、1993年度1月に実施した照射済BWR燃料を用いた5回目の反応度事故模擬実験であるTS-5について、実験データをまとめたものである。TS-4実験に使用した試験燃料は、初期濃縮度2.79%であり、日本原子力発電(株)の敦賀1号炉で照射されたBWR7times7型燃料棒を短尺化したものである。短尺化に供した燃料の燃焼度は26GWd/tUであった。NSRRにおける照射実験は、BWRのコールドスタートアップ条件を模擬した大気圧・室温の静止水冷却条件下で行い、公称発熱量は117pm5cal/g・fuel(ピークエンタルピ98pm4cal/g・fuel)を与えた。その結果燃料破損は生じなかった。なお、この実験では集合体中の燃料/水比を模した流路管中で燃料のパルス照射を行った。実験条件、実験方法、パルス照射時の燃料の過渡挙動及び照射後検査の結果をまとめて示した。...

  10. Performance and Emission Characteristics on Glow Plug Hot Surface Ignition C.I. Engine Using Methanol as Fuel With Additive

    Directory of Open Access Journals (Sweden)

    B.OMPRAKASH

    2015-07-01

    Full Text Available The concept of using alcohol fuels as alternative to diesel fuel in diesel engine is recent one. The scarcity of transportation petroleum fuels due to the fast depletion of the petroleum deposits and frequent rise in their costs in the international market have spurred many efforts to find alternatives. Alcohols were quickly recognized as prime candidates to displace or replace high octane petroleum fuels. Innovative thinking led to find varies techniques by which alcohol can be used as fuel in diesel engine. Amongst the fuel alternative proposed, the most favourest ones are methanol and ethanol. The specific tendency of alcohols to ignite easily from a hot surface makes it suitable to ignite in a diesel engine by different methods. The advantage of this property of alcohols enables to design and construct a new type of engine called surface ignition engine. Methanol and ethanol are very susceptible to surface ignition, this method is very suitable for these fuels. The hot surfaces which, can be used in surface ignition engine are electrically heated glow plug with hot surface. Hence present research work carries the experimental investigation on glow plug hot surface ignition engine, by adding different additives with methanol and ethanol as fuels, with an objective to find the best one performance, emission and compression parameters.

  11. Synthesis of homochiral tris-indanyl molecular rods

    DEFF Research Database (Denmark)

    Kjeldsen, Niels Due; Funder, Erik Daa; Gothelf, Kurt Vesterager

    2014-01-01

    Homochiral tris-indanyl molecular rods designed for supramolecular surface self-assembly were synthesized. The chiral indanol moiety was constructed via a Ti-mediated alkyne trimerization. Further manipulations resulted in a homochiral indanol monomer. This was employed as the precursor...... for successive Sonogashira and Ohira-Bestman reactions towards the homochiral tris-indanyl molecular rods. The molecular rods will be applied for scanning tunnelling microscopy studies of their surface self-assembly and chirality....

  12. Granular materials interacting with thin flexible rods

    Science.gov (United States)

    Neto, Alfredo Gay; Campello, Eduardo M. B.

    2017-04-01

    In this work, we develop a computational model for the simulation of problems wherein granular materials interact with thin flexible rods. We treat granular materials as a collection of spherical particles following a discrete element method (DEM) approach, while flexible rods are described by a large deformation finite element (FEM) rod formulation. Grain-to-grain, grain-to-rod, and rod-to-rod contacts are fully permitted and resolved. A simple and efficient strategy is proposed for coupling the motion of the two types (discrete and continuum) of materials within an iterative time-stepping solution scheme. Implementation details are shown and discussed. Validity and applicability of the model are assessed by means of a few numerical examples. We believe that robust, efficiently coupled DEM-FEM schemes can be a useful tool to the simulation of problems wherein granular materials interact with thin flexible rods, such as (but not limited to) bombardment of grains on beam structures, flow of granular materials over surfaces covered by threads of hair in many biological processes, flow of grains through filters and strainers in various industrial segregation processes, and many others.

  13. Granular materials interacting with thin flexible rods

    Science.gov (United States)

    Neto, Alfredo Gay; Campello, Eduardo M. B.

    2016-01-01

    In this work, we develop a computational model for the simulation of problems wherein granular materials interact with thin flexible rods. We treat granular materials as a collection of spherical particles following a discrete element method (DEM) approach, while flexible rods are described by a large deformation finite element (FEM) rod formulation. Grain-to-grain, grain-to-rod, and rod-to-rod contacts are fully permitted and resolved. A simple and efficient strategy is proposed for coupling the motion of the two types (discrete and continuum) of materials within an iterative time-stepping solution scheme. Implementation details are shown and discussed. Validity and applicability of the model are assessed by means of a few numerical examples. We believe that robust, efficiently coupled DEM-FEM schemes can be a useful tool to the simulation of problems wherein granular materials interact with thin flexible rods, such as (but not limited to) bombardment of grains on beam structures, flow of granular materials over surfaces covered by threads of hair in many biological processes, flow of grains through filters and strainers in various industrial segregation processes, and many others.

  14. High temperature control rod assembly

    Energy Technology Data Exchange (ETDEWEB)

    Vollman, Russell E. (Solana Beach, CA)

    1991-01-01

    A high temperature nuclear control rod assembly comprises a plurality of substantially cylindrical segments flexibly joined together in succession by ball joints. The segments are made of a high temperature graphite or carbon-carbon composite. The segment includes a hollow cylindrical sleeve which has an opening for receiving neutron-absorbing material in the form of pellets or compacted rings. The sleeve has a threaded sleeve bore and outer threaded surface. A cylindrical support post has a threaded shaft at one end which is threadably engaged with the sleeve bore to rigidly couple the support post to the sleeve. The other end of the post is formed with a ball portion. A hollow cylindrical collar has an inner threaded surface engageable with the outer threaded surface of the sleeve to rigidly couple the collar to the sleeve. the collar also has a socket portion which cooperates with the ball portion to flexibly connect segments together to form a ball and socket-type joint. In another embodiment, the segment comprises a support member which has a threaded shaft portion and a ball surface portion. The threaded shaft portion is engageable with an inner threaded surface of a ring for rigidly coupling the support member to the ring. The ring in turn has an outer surface at one end which is threadably engageably with a hollow cylindrical sleeve. The other end of the sleeve is formed with a socket portion for engagement with a ball portion of the support member. In yet another embodiment, a secondary rod is slidably inserted in a hollow channel through the center of the segment to provide additional strength. A method for controlling a nuclear reactor utilizing the control rod assembly is also included.

  15. Multifractal analysis of slacken surface in hydrocarbon molecules through fuel additives

    Directory of Open Access Journals (Sweden)

    G. Arockia Prabakar

    2014-09-01

    Full Text Available This paper investigates the effect of organic fuel additives (Bio-Glycerol on fuel savings, emission reduction and extend engine life. Using this enzyme, a motor cycle is tested five times. The test report shows the reduction in the release of carbon monoxide (CO and hydrocarbon upto 60%. The use of organic fuel additives in diesel vehicles for different periods of time reveals the reduction in air pollution by 55%. Finally, we have experimented scanning electron microscope (SEM test for organic fuel additives with biodiesel. The SEM image shows the existence of molecules of hydrocarbons. The analysis elucidated the complex morphology of molecules of hydrocarbons in fuel additives with biodiesel. The hydrocarbon molecules are slackened and irregular as it refers to the fractal form. SEM Photograph images are analyzed by multifractal analysis. MFA (multifractal analysis is carried out according to the method of moments, i.e., the probability distribution is estimated for moments which differ from -150surface.

  16. Mass transfer in fuel cells. [electron microscopy of components, thermal decomposition of Teflon, water transport, and surface tension of KOH solutions

    Science.gov (United States)

    Walker, R. D., Jr.

    1973-01-01

    Results of experiments on electron microscopy of fuel cell components, thermal decomposition of Teflon by thermogravimetry, surface area and pore size distribution measurements, water transport in fuel cells, and surface tension of KOH solutions are described.

  17. A comparison of mechanical algorithms of fuel performance code systems

    Energy Technology Data Exchange (ETDEWEB)

    Park, C. J.; Park, J. H.; Kang, K. H.; Ryu, H. J.; Moon, J. S.; Jeong, I. H.; Lee, C. Y.; Song, K. C

    2003-11-01

    The goal of fuel rod performance evaluation is to identify the robustness of fuel rod with cladding material during fuel irradiation. Computer simulation of fuel rod performance becomes important to develop new nuclear systems. To construct the computing code system for fuel rod performance, we compared several algorithms of existing fuel rod performance code systems and summarized the details and tips as a preliminary work. Among several code systems, FRAPCON, FEMAXI for LWR, ELESTRES for CANDU reactor, and LIFE for fast reactor are reviewed. The computational algorithms related to mechanical interaction of the fuel rod are compared including methodologies and subroutines. This work will be utilized to develop the computing code system for dry process fuel rod performance.

  18. Optimized Control Rods of the BR2 Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kalcheva, Silva; Koonen, E.

    2007-09-15

    At the present time the BR-2 reactor uses control elements with cadmium as neutron absorbing part. The lower section of the control element is a beryllium assembly cooled by light water. Due to the burn up of the lower end of the cadmium section during the reactor operation, the presently used rods for reactivity control of the BR-2 reactor have to be replaced by new ones. Considered are various types Control Rods with full active part of the following materials: cadmium (Cd), hafnium (Hf), europium oxide (Eu2O3) and gadolinium (Gd2O3). Options to decrease the burn up of the control rod material in the hot spot, such as use of stainless steel in the lower active part of the Control Rod are discussed. Comparison with the characteristics of the presently used Control Rods types is performed. The changing of the characteristics of different types Control Rods and the perturbation effects on the reactor neutronics during the BR-2 fuel cycle are investigated. The burn up of the Control Rod absorbing material, total and differential control rods worth, macroscopic and effective microscopic absorption cross sections, fuel and reactivity evolution are evaluated during approximately 30 operating cycles.

  19. Investigation on surface decarburization of hot rolled wire rod for P72LXA steel cord%P72LXA钢帘线用热轧盘条表面脱碳层的研究

    Institute of Scientific and Technical Information of China (English)

    赵如龙; 李义长; 王洪利; 李荣华; 张颖刚; 赵平

    2013-01-01

    研究了P72LXA钢帘线用热轧盘条表面脱碳层的主要影响因素.生产试验得出:在热轧过程中通过减小加热炉烧嘴的开启程度和适当提高吐丝温度可以降低P72LXA钢帘线用热轧盘条表面脱碳层深度;最佳轧制工艺下,坯料原始脱碳对成品盘条表面脱碳层的遗传影响关系y=0.687x0.637.结果表明,要有效地控制成品盘条表面脱碳,坯料原始脱碳层深度须≤1200 μm.%Effects of surface decarburization of wire rod for P72LXA steel cord during hot rolling were studied.The surface decarburization layer thickness of wire rod for P72LXA steel cord could be decreased by means of reducing opening of some heating furnace nozzles and raising spinning temperature moderately during hot rolling.Based on the optimal rolling technology,the genetic influence relationship of previous decarburization of billet on decarburization of wire rod for P72LXA steel cord is y =0.687x0.637,and the results show that the previous decarburization layer thickness of billet should be less than 1200 μm to control decarburization of wire rod effectively.

  20. Wetting of a partially immersed compliant rod

    Science.gov (United States)

    Hui, Chung-Yuen; Jagota, Anand

    2016-11-01

    The force on a solid rod partially immersed in a liquid is commonly used to determine the liquid-vapor surface tension by equating the measured force required to remove the rod from the liquid to the vertical component of the liquid-vapor surface tension. Here, we study how this process is affected when the rod is compliant. For equilibrium, we enforce force and configurational energy balance, including contributions from elastic energy. We show that, in general, the contact angle does not equal that given by Young's equation. If surface stresses are tensile, the strain in the immersed part of the rod is found to be compressive and to depend only on the solid-liquid surface stress. The strain in the dry part of the rod can be either tensile or compressive, depending on a combination of parameters that we identify. We also provide results for compliant plates partially immersed in a liquid under plane strain and plane stress. Our results can be used to extract solid surface stresses from such experiments.

  1. Self-limiting adsorption of Eu³⁺ on the surface of rod-shape anatase TiO₂ nanocrystals and post-synthetic sensitization of the europium-based emission.

    Science.gov (United States)

    Balasanthiran, Choumini; Zhao, Bo; Lin, Cuikun; May, P S; Berry, Mary T; Hoefelmeyer, James D

    2015-12-01

    The surface of oleic acid stabilized rod-shape anatase TiO2 nanocrystals was modified by adsorption of Eu(3+) ions. The Eu(3+) attachment showed Langmuir adsorption behavior, thus the loading of Eu(3+) could be controlled precisely up to surface saturation coverage. The Eu(3+)-TiO2 nanorods show weak Eu(3+) based luminescence. However, addition of thenoyltrifluoroacetone (TTFA) leads to coordination of the ligand to the Eu(3+) centers and the TTFA-Eu(3+)-TiO2 materials exhibit strong Eu(3+) fluorescence sensitized by the TTFA ligand.

  2. Surface modification techniques for increased corrosion tolerance of zirconium fuel cladding

    Science.gov (United States)

    Carr, James Patrick, IV

    Corrosion is a major issue in applications involving materials in normal and severe environments, especially when it involves corrosive fluids, high temperatures, and radiation. Left unaddressed, corrosion can lead to catastrophic failures, resulting in economic and environmental liabilities. In nuclear applications, where metals and alloys, such as steel and zirconium, are extensively employed inside and outside of the nuclear reactor, corrosion accelerated by high temperatures, neutron radiation, and corrosive atmospheres, corrosion becomes even more concerning. The objectives of this research are to study and develop surface modification techniques to protect zirconium cladding by the incorporation of a specific barrier coating, and to understand the issues related to the compatibility of the coatings examined in this work. The final goal of this study is to recommend a coating and process that can be scaled-up for the consideration of manufacturing and economic limits. This dissertation study builds on previous accident tolerant fuel cladding research, but is unique in that advanced corrosion methods are tested and considerations for implementation by industry are practiced and discussed. This work will introduce unique studies involving the materials and methods for accident tolerant fuel cladding research by developing, demonstrating, and considering materials and processes for modifying the surface of zircaloy fuel cladding. This innovative research suggests that improvements in the technique to modify the surface of zirconium fuel cladding are likely. Three elements selected for the investigation of their compatibility on zircaloy fuel cladding are aluminum, silicon, and chromium. These materials are also currently being investigated at other labs as alternate alloys and coatings for accident tolerant fuel cladding. This dissertation also investigates the compatibility of these three elements as surface modifiers, by comparing their microstructural and

  3. High-throughput rod-induced electrospinning

    Science.gov (United States)

    Wu, Dezhi; Xiao, Zhiming; Teh, Kwok Siong; Han, Zhibin; Luo, Guoxi; Shi, Chuan; Sun, Daoheng; Zhao, Jinbao; Lin, Liwei

    2016-09-01

    A high throughput electrospinning process, directly from flat polymer solution surfaces induced by a moving insulating rod, has been proposed and demonstrated. Different rods made of either phenolic resin or paper with a diameter of 1-3 cm and a resistance of about 100-500 MΩ, has been successfully utilized in the process. The rod is placed approximately 10 mm above the flat polymer solution surface with a moving speed of 0.005-0.4 m s-1 this causes the solution to generate multiple liquid jets under an applied voltage of 15-60 kV for the tip-less electrospinning process. The local electric field induced by the rod can boost electrohydrodynamic instability in order to generate Taylor cones and liquid jets. Experimentally, it is found that a large rod diameter and a small solution-to-rod distance can enhance the local electrical field to reduce the magnitude of the applied voltage. In the prototype setup with poly (ethylene oxide) polymer solution, an area of 5 cm  ×  10 cm and under an applied voltage of 60 kV, the maximum throughput of nanofibers is recorded to be approximately144 g m-2 h-1.

  4. New results from the NSRR experiments with high burnup fuel

    Energy Technology Data Exchange (ETDEWEB)

    Fuketa, Toyoshi; Ishijima, Kiyomi; Mori, Yukihide [Japan Atomic Research Institute, Toaki, Ibaraki (Japan)] [and others

    1996-03-01

    Results obtained in the NSRR power burst experiments with irradiated PWR fuel rods with fuel burnup up to 50 MWd/kgU are described and discussed in this paper. Data concerning test method, test fuel rod, pulse irradiation, transient records during the pulse and post irradiation examination are described, and interpretations and discussions on fission gas release and fuel pellet fragmentation are presented. During the pulse-irradiation experiment with 50 MWd/kgU PWR fuel rod, the fuel rod failed at considerably low energy deposition level, and large amount of fission gas release and fragmentation of fuel pellets were observed.

  5. Effect of Microscale Surface Geometry of Electrodes on Performance of Microbial Fuel Cells

    Science.gov (United States)

    Kano, Tomonori; Suito, Eiichi; Hishida, Koichi; Miki, Norihisa

    2012-06-01

    In this study, we experimentally revealed that the microscale surface geometry of anodes strongly affects the performance of microbial fuel cells (MFCs). MFCs have much need to be improved in their power. The power generated by an MFC is considered to be strongly affected by the interaction between the organic bacteria and the inorganic electrode surfaces. In prior work, the nanoscale surface roughness of the anode was discussed; however, we consider that the microscale surface geometry may play a crucial role given the bacteria size of micrometer order. We used a two-chamber MFC and the direct electron transfer bacteria Shewanella putrefaciens. We prepared seven types of anode electrodes with different microscale surface geometries and experimentally found that the MFC performance depended on the contact area between the bacteria and the anode. The MFC generated the maximum power when the contact area between the anode and bacteria was the largest.

  6. New approaches to predicting surface fuel moisture in south east Australian forests

    Science.gov (United States)

    Sheridan, Gary; Nyman, Petter; Hawthorne, Sandra; Bovill, William; Walsh, Sean; Baillie, Craig; Duff, Thomas; Tolhurst, Kevin; Lane, Patrick

    2016-04-01

    The capacity to predict of the moisture content (FMC) of fine surface fuels in mountainous south east Australian forests has improved dramatically in recent years due to the convergence of several new technologies, including i) improved process-based account-keeping type FMC models, ii) improved understanding and representation of topographic effects (aspect, drainage position, elevation) on surface fuel and soil moisture, iii) improved methods for downscaling weather variables (eg. rainfall/throughfall, short-wave radiation) using digital elevation models and airborne LIDaR, and, iv) new in-situ sensor technologies (fuelsticks, capacitance sensors, Ibuttons) for continuously monitoring surface fuels and within-litter micro-climate conditions, generating datasets of unprecedented temporal resolution and continuity for model development and testing under real field conditions across a broad range of forests, landscapes and climates. In this study the combined improvements in predictive capacity were quantified by comparing the field FMC observations with predictions from traditional, widely used operational FMC models, and with two new process-based models, including improved spatial parameterisation provided by the new technologies outlined above. The results are interpreted in the context of planned-burning decision making and outcomes, and bushfire modelling and management. The initial results showed that the new approaches to FMC prediction offered substantial improvements over the traditional methods and could be reasonably implemented at operational scales.

  7. Graphite anode surface modification with controlled reduction of specific aryl diazonium salts for improved microbial fuel cells power output.

    Science.gov (United States)

    Picot, Matthieu; Lapinsonnière, Laure; Rothballer, Michael; Barrière, Frédéric

    2011-10-15

    Graphite electrodes were modified with reduction of aryl diazonium salts and implemented as anodes in microbial fuel cells. First, reduction of 4-aminophenyl diazonium is considered using increased coulombic charge density from 16.5 to 200 mC/cm(2). This procedure introduced aryl amine functionalities at the surface which are neutral at neutral pH. These electrodes were implemented as anodes in "H" type microbial fuel cells inoculated with waste water, acetate as the substrate and using ferricyanide reduction at the cathode and a 1000 Ω external resistance. When the microbial anode had developed, the performances of the microbial fuel cells were measured under acetate saturation conditions and compared with those of control microbial fuel cells having an unmodified graphite anode. We found that the maximum power density of microbial fuel cell first increased as a function of the extent of modification, reaching an optimum after which it decreased for higher degree of surface modification, becoming even less performing than the control microbial fuel cell. Then, the effect of the introduction of charged groups at the surface was investigated at a low degree of surface modification. It was found that negatively charged groups at the surface (carboxylate) decreased microbial fuel cell power output while the introduction of positively charged groups doubled the power output. Scanning electron microscopy revealed that the microbial anode modified with positively charged groups was covered by a dense and homogeneous biofilm. Fluorescence in situ hybridization analyses showed that this biofilm consisted to a large extent of bacteria from the known electroactive Geobacter genus. In summary, the extent of modification of the anode was found to be critical for the microbial fuel cell performance. The nature of the chemical group introduced at the electrode surface was also found to significantly affect the performance of the microbial fuel cells. The method used for

  8. Dynamics of water droplets detached from porous surfaces of relevance to PEM fuel cells.

    Science.gov (United States)

    Theodorakakos, A; Ous, T; Gavaises, M; Nouri, J M; Nikolopoulos, N; Yanagihara, H

    2006-08-15

    The detachment of liquid droplets from porous material surfaces used with proton exchange membrane (PEM) fuel cells under the influence of a cross-flowing air is investigated computationally and experimentally. CCD images taken on a purpose-built transparent fuel cell have revealed that the water produced within the PEM is forming droplets on the surface of the gas-diffusion layer. These droplets are swept away if the velocity of the flowing air is above a critical value for a given droplet size. Static and dynamic contact angle measurements for three different carbon gas-diffusion layer materials obtained inside a transparent air-channel test model have been used as input to the numerical model; the latter is based on a Navier-Stokes equations flow solver incorporating the volume of fluid (VOF) two-phase flow methodology. Variable contact angle values around the gas-liquid-solid contact-line as well as their dynamic change during the droplet shape deformation process, have allowed estimation of the adhesion force between the liquid droplet and the solid surface and successful prediction of the separation line at which droplets loose their contact from the solid surface under the influence of the air stream flowing around them. Parametric studies highlight the relevant importance of various factors affecting the detachment of the liquid droplets from the solid surface.

  9. Mechanical Behavior of Free-Standing Fuel Cell Electrodes on Water Surface.

    Science.gov (United States)

    Kim, Sanwi; Kim, Jae-Han; Oh, Jong-Gil; Jang, Kyung-Lim; Jeong, Byeong-Heon; Hong, Bo Ki; Kim, Taek-Soo

    2016-06-22

    Fundamental understanding of the mechanical behavior of polymer electrolyte fuel cell electrodes as free-standing materials is essential to develop mechanically robust fuel cells. However, this has been a significant challenge due to critical difficulties, such as separating the pristine electrode from the substrate without damage and precisely measuring the mechanical properties of the very fragile and thin electrodes. We report the mechanical behavior of free-standing fuel cell electrodes on the water surface through adopting an innovative ice-assisted separation method to separate the electrode from decal transfer film. It is found that doubling the ionomer content in electrodes increases not only the tensile stress at the break and the Young's modulus (E) of the electrodes by approximately 2.1-3.5 and 1.7-2.4 times, respectively, but also the elongation at the break by approximately 1.5-1.7 times, which indicates that stronger, stiffer, and tougher electrodes are attained with increasing ionomer content, which have been of significant interest in materials research fields. The scaling law relationship between Young's modulus and density (ρ) has been unveiled as E ∼ ρ(1.6), and it is compared with other materials. These findings can be used to develop mechanically robust electrodes for fuel cell applications.

  10. High-yield production of hydrophobins RodA and RodB from Aspergillus fumigatus in Pichia pastoris.

    Science.gov (United States)

    Pedersen, Mona Højgaard; Borodina, Irina; Moresco, Jacob Lange; Svendsen, Winnie Edith; Frisvad, Jens Christian; Søndergaard, Ib

    2011-06-01

    Hydrophobins are small fungal proteins with amphipatic properties and the ability to self-assemble on a hydrophobic/hydrophilic interface; thus, many technical applications for hydrophobins have been suggested. The pathogenic fungus Aspergillus fumigatus expresses the hydrophobins RodA and RodB on the surface of its conidia. RodA is known to be of importance to the pathogenesis of the fungus, while the biological role of RodB is currently unknown. Here, we report the successful expression of both hydrophobins in Pichia pastoris and present fed-batch fermentation yields of 200-300 mg/l fermentation broth. Protein bands of expected sizes were detected by SDS-PAGE and western blotting, and the identity was further confirmed by tandem mass spectrometry. Both proteins were purified using his-affinity chromatography, and the high level of purity was verified by silver-stained SDS-PAGE. Recombinant RodA as well as rRodB were able to convert a glass surface from hydrophilic to hydrophobic similar to native RodA, but only rRodB was able to decrease the hydrophobicity of a Teflon-like surface to the same extent as native RodA, while rRodA showed this ability to a lesser extent. Recombinant RodA and native RodA showed a similar ability to emulsify air in water, while recombinant RodB could also emulsify oil in water better than the control protein bovine serum albumin (BSA). This is to our knowledge the first successful expression of hydrophobins from A. fumigatus in a eukaryote host, which makes it possible to further characterize both hydrophobins. Furthermore, the expression strategy and fed-batch production using P. pastoris may be transferred to hydrophobins from other species.

  11. Qualification of the B and W Mark B fuel assembly for high burnup. Third semi-annual progress report, July-December 1979

    Energy Technology Data Exchange (ETDEWEB)

    Coleman, T.A.

    1980-03-01

    Five Babcock and Wilcox-designed Mark B (15 x 15) pressurized water reactor fuel assemblies were irradiated to extended burnups in Duke Power Company's Oconee Unit 1 reactor. An assembly average burnup of 40,000 MWd/mtU, which is about 29% greater than previous discharge burnups at Oconee 1, was attained. The nondestructive examination of these five assemblies, which have been irradiated for four fuel cycles, was begun. Data obtained included fuel assembly and fuel dimensions, water channel spacings, fuel rod surface deposit samples, and holddown spring preload forces. Visual examination of the assemblies indicated that good fuel performance was maintained through four cycles of irradiation.

  12. Use of Supplemental Short Pre-Contoured Accessory Rods and Cobalt Chrome Alloy Posterior Rods Reduces Primary Rod Strain and Range of Motion Across the Pedicle Subtraction Osteotomy Level

    DEFF Research Database (Denmark)

    Hallager, Dennis Winge; Gehrchen, Poul Martin; Dahl, Benny

    2016-01-01

    STUDY DESIGN: In vitro cadaveric biomechanical study. OBJECTIVE: To assess effects of 4-rod reconstruction, rod material, and anterior column support on motion and surface rod strain in a pedicle subtraction osteotomy model. SUMMARY OF BACKGROUND DATA: Pedicle subtraction osteotomy (PSO) can corr...

  13. Volatile organic compounds (VOCs) in surface coating materials: Their compositions and potential as an alternative fuel.

    Science.gov (United States)

    Dinh, Trieu-Vuong; Choi, In-Young; Son, Youn-Suk; Song, Kyu-Yong; Sunwoo, Young; Kim, Jo-Chun

    2016-03-01

    A sampling system was designed to determine the composition ratios of VOCs emitted from 31 surface coating materials (SCMs). Representative architectural, automotive, and marine SCMs in Korea were investigated. Toluene, ethylbenzene, and xylene were the predominant VOCs. The VOC levels (wt%) from automotive SCMs were significantly higher than those from architectural and marine paints. It was found that target SCMs comprised mainly VOCs with 6-10 carbon atoms in molecules, which could be adsorbed by activated carbon. The saturated activated carbon which had already adsorbed toluene, ethylbenzene, and m-xylene was combusted. The saturated activated carbon was more combustible than new activated carbon because it comprised inflammable VOCs. Therefore, it could be an alternative fuel when using in a "fuelization system". To use the activated carbon as a fuel, a control technology of VOCs from a coating process was also designed and introduced.

  14. Analysis of rolled-in oxide scale on ER70S-6 steel wire rods surface%ER70S-6焊丝钢盘条表面氧化皮压入分析

    Institute of Scientific and Technical Information of China (English)

    周铖; 麻晗; 黄文克; 李平; 峰公雄

    2011-01-01

    ER70S-6盘条表面存在大量氧化皮压入基体现象,严重影响焊丝成品表面质量和焊接性能,易产生表面红锈。通过调整除鳞水压从8 MPa提高到20 MPa和优化加热炉工艺,方坯除鳞效果得到明显改善,压入氧化皮明显减少。同时,焊接飞溅和表面红锈也明显减少。%Plentiful rolled-in oxide scale was observed in the ER70S-6 wire rods,it deteriorated the surface quality and welding properties of welding wire,and induced red rust.The descaling effect was improved and the rolled-in scale was obviously reduced by increasing the descaling pressure from 8 MPa to 20 MPa and improving the reheating process.The welding spatter and red rust were also reduced obviously.

  15. The neutron emission method for determination of fissile materials within the spent fuel equipment optimization

    Energy Technology Data Exchange (ETDEWEB)

    Abou-Zaid, A. [Nuclear Research Center, Atomic Energy Authority, 13759- Cairo (Ethiopia); Pytel, K. [Atomic Energy Institute, Research Reactor Center, 05-400 Otwock-Swierk (Poland)

    1998-07-01

    A nondestructive assay method using neutron technique for determination of the fissile isotopes content along the irradiated fuel rods of MARIA reactor is presented. This method is based on detection of the fission neutrons emitted from external neutron source and multiplied by the fissile isotopes U-235, Pu-239, and Pu-241 within the fuel rod. Neutrons emitted from the spent fuel originate mainly from induced fission in the fissile material and source neutrons penetrating the fuel rod without interaction. Additionally, the neutrons from ({alpha}, n) reaction and spontaneous fission of actinide isotopes contribute in the total population of emitted ones. The method gives a chance to perform an experimental calibration of the equipment using two points: fresh fuel rod (maximum signal plus background) and its mock-up (background). The Monte Carlo code has been used for the geometrical simulation and optimization of the measuring equipment: neutron source, moderating container, collimator, and the neutron detector. The results of the calculation show that the moderating container of 30 cm length and 32 cm diameter and a collimator of 26 cm length, 6.8 cm width, and 2 cm height are the optimal configuration. With respect to the fission chamber position, the number of neutrons has been calculated as a function of distance from the fuel rod surface in the case of fresh fuel and its mock-up. The distance, at which the ratio of the signal to background has its maximum, has been found at 4.5 cm far from the outer surface of the fuel. (author)

  16. Enhanced Photocatalytic Activity of Bismuth Precursor by Rapid Phase and Surface Transformation Using Structure-Guided Combustion Waves.

    Science.gov (United States)

    Lee, Kang Yeol; Hwang, Hayoung; Kim, Tae Ho; Choi, Wonjoon

    2016-02-10

    The development of an efficient method for manipulating phase and surface transformations would facilitate the improvement of catalytic materials for use in a diverse range of applications. Herein, we present the first instance of a submicrosecond time frame direct phase and surface transformation of Bi(NO3)3 rods to nanoporous β-Bi2O3 rods via structure-guided combustion waves. Hybrid composites of the prepared Bi(NO3)3·H2O rods and organic fuel were fabricated by a facile preparation method. The anisotropic propagation of combustion waves along the interfacial boundaries of Bi(NO3)3·H2O rods induced direct phase transformation to β-Bi2O3 rods in the original structure due to the rapid pyrolysis, while the release of gas molecules enabled the formation of nanoporous structures on the surfaces of rods. The developed β-Bi2O3 rods showed improved photocatalytic activity for the photodegradation of rhodamine B in comparison with Bi(NO3)3·H2O rods and α-Bi2O3 rods due to the more suitable interdistance and the large contact areas of the porous surfaces. This new method of using structure-guided combustion waves for phase and surface transformation may contribute to the development of new catalysts as well as the precise manipulation of diverse micronanostructured materials.

  17. Surface modification of a proton exchange membrane and hydrogen storage in a metal hydride for fuel cells

    Science.gov (United States)

    Andrews, Lisa

    Interest in fuel cell technology is rising as a result of the need for more affordable and available fuel sources. Proton exchange membrane fuel cells involve the catalysis of a fuel to release protons and electrons. It requires the use of a polymer electrolyte membrane to transfer protons through the cell, while the electrons pass through an external circuit, producing electricity. The surface modification of the polymer, NafionRTM, commonly researched as a proton exchange membrane, may improve efficiency of a fuel cell. Surface modification can change the chemistry of the surface of a polymer while maintaining bulk properties. Plasma modification techniques such as microwave discharge of an argon and oxygen gas mixture as well as vacuum-ultraviolet (VUV) photolysis may cause favorable chemical and physical changes on the surface of Nafion for improved fuel cell function. A possible increase in hydrophilicity as a result of microwave discharge experiments may increase proton conductivity. Grafting of acrylic acid from the surface of modified Nafion may decrease the permeation of methanol in a direct methanol fuel cell, a process which can decrease efficiency. Modification of the surface of Nafion samples were carried out using: 1) An indirect Ar/O2 gas mixture plasma investigating the reaction of oxygen radicals with the surface, 2) A direct Ar/O2 gas mixture plasma investigating the reaction of oxygen radicals and VUV radiation with the surface and, 3) VUV photolysis investigating exclusively the interaction of VUV radiation with the surface and any possible oxidation upon exposure to air. Acrylic acid was grafted from the VUV photolysed Nafion samples. All treated surfaces were analyzed using X-ray photoelectron spectroscopy (XPS). Fourier transform infrared spectroscopy (FTIR) was used to analyze the grafted Nafion samples. Scanning electron microscopy (SEM) and contact angle measurements were used to analyze experiments 2 and 3. Using hydrogen as fuel is a

  18. Changes of surface structure and elemental composition of Pd rod and collector of nuclear reaction products irradiated with 10-MeV γ-quanta in dense deuterium gas

    Science.gov (United States)

    Didyk, A. Yu.; Wiśniewski, R.; Wilczynska-Kitowska, T.

    2013-12-01

    A high-pressure chamber is filled with 1.2 kbar molecular deuterium (DHPC). The palladium rod saturated with deuterium is loaded inside the DHPC and irradiated with 10-MeV bremsstrahlung γ-quanta for 18 h with a 11-13 μA electron beam using the MT-25 electron accelerator. The elemental compositions of all surfaces of the DHPC element inside the dense deuterium gas were studied using scanning electronic microscopes with X-ray microelement microprobe analysis. It is found that all surfaces, including the surface of a high-purity palladium rod (99.995%), are covered with a partly homogeneous layer or large microparticles of lead. Also, light elements such as 6C, 8O, 11Na, 12Mg, 13Al, 14Si, 22Ti, 25Mn, 26Fe, 29Cu, and 30Zn and heavy metals such as 47Ag, 73Ta, 74W, 78Pt, 79Au, and 82Pb are observed. Possible processes that can cause the anomalies observed in the newly formed chemical elements are briefly discussed.

  19. Metallic Reactor Fuel Fabrication for SFR

    Energy Technology Data Exchange (ETDEWEB)

    Song, Hoon; Kim, Jong-Hwan; Ko, Young-Mo; Woo, Yoon-Myung; Kim, Ki-Hwan; Lee, Chan-Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    The metal fuel for an SFR has such advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant, and inherent passive safety 1. U-Zr metal fuel for SFR is now being developed by KAERI as a national R and D program of Korea. The fabrication technology of metal fuel for SFR has been under development in Korea as a national nuclear R and D program since 2007. The fabrication process for SFR fuel is composed of (1) fuel slug casting, (2) loading and fabrication of the fuel rods, and (3) fabrication of the final fuel assemblies. Fuel slug casting is the dominant source of fuel losses and recycled streams in this fabrication process. Fabrication on the rod type metallic fuel was carried out for the purpose of establishing a practical fabrication method. Rod-type fuel slugs were fabricated by injection casting. Metallic fuel slugs fabricated showed a general appearance was smooth.

  20. Vortex patterns in a superconducting-ferromagnetic rod

    Energy Technology Data Exchange (ETDEWEB)

    Romaguera, Antonio R. de C, E-mail: antonio.romaguera@df.ufrpe.b [Departamento de Fi' sica, Universidade Federal Rural de Pernambuco, 52171-900 Recife, Pernambuco (Brazil); Doria, Mauro M. [Departamento de Fi' sica dos Solidos, Universidade Federal do Rio de Janeiro, 21941-972 Rio de Janeiro (Brazil); Peeters, Francois M. [Departement Fysica, Universiteit Antwerpen, Groenenborgerlaan 171, B-2020 Antwerpen (Belgium)

    2010-10-01

    A superconducting rod with a magnetic moment on top develops vortices obtained here through 3D calculations of the Ginzburg-Landau theory. The inhomogeneity of the applied field brings new properties to the vortex patterns that vary according to the rod thickness. We find that for thin rods (disks) the vortex patterns are similar to those obtained in presence of a homogeneous magnetic field instead because they consist of giant vortex states. For thick rods novel patterns are obtained as vortices are curve lines in space that exit through the lateral surface.

  1. Loss of retinoschisin (RS1) cell surface protein in maturing mouse rod photoreceptors elevates the luminance threshold for light-driven translocation of transducin but not arrestin.

    Science.gov (United States)

    Ziccardi, Lucia; Vijayasarathy, Camasamudram; Bush, Ronald A; Sieving, Paul A

    2012-09-19

    Loss of retinoschisin (RS1) in Rs1 knock-out (Rs1-KO) retina produces a post-photoreceptor phenotype similar to X-linked retinoschisis in young males. However, Rs1 is expressed strongly in photoreceptors, and Rs1-KO mice have early reduction in the electroretinogram a-wave. We examined light-activated transducin and arrestin translocation in young Rs1-KO mice as a marker for functional abnormalities in maturing rod photoreceptors. We found a progressive reduction in luminance threshold for transducin translocation in wild-type (WT) retinas between postnatal days P18 and P60. At P21, the threshold in Rs1-KO retinas was 10-fold higher than WT, but it decreased to translocation and re-translocation of transducin in the dark were not affected. Rs1-KO rod outer segment (ROS) length was significantly shorter than WT at P21 but was comparable with WT at P60. These findings suggested a delay in the structural and functional maturation of Rs1-KO ROS. Consistent with this, transcription factors CRX and NRL, which are fundamental to maturation of rod protein expression, were reduced in ROS of Rs1-KO mice at P21 but not at P60. Expression of transducin was 15-30% lower in P21 Rs1-KO ROS and transducin GTPase hydrolysis was nearly twofold faster, reflecting a 1.7- to 2.5-fold increase in RGS9 (regulator of G-protein signaling) level. Transduction protein expression and activity levels were similar to WT at P60. Transducin translocation threshold elevation indicates photoreceptor functional abnormalities in young Rs1-KO mice. Rapid reduction in threshold coupled with age-related changes in transduction protein levels and transcription factor expression are consistent with delayed maturation of Rs1-KO photoreceptors.

  2. Control wetting state transition by micro-rod geometry

    Science.gov (United States)

    He, Yang; Jiang, Chengyu; Wang, Shengkun; Yin, Hengxu; Yuan, Weizheng

    2013-11-01

    Understanding the effect of micro-structure geometry on wetting state transition is important to design and control surface wettability. Micro-rod model was proposed and the relationship between micro-rod geometry and wetting state was investigated in the paper taking into account only the surface roughness and neglecting the chemistry interaction. Micro-rods with different geometric parameters were fabricated using micro-fabrication technology. Their contact angles were measured and compared with theoretical ones. The experimental results indicated that increasing the height and decreasing the space of micro-rod may result in Cassie wetting state, while decreasing the height and increasing the space may result in Wenzel wetting state. A suspended wetting state model due to scallops was proposed. The wetting state transition was interpreted by intruding height, de-pinning and sag mechanism. It may offer a facile way to control the surface wetting state transition by changing the geometry of micro-rod.

  3. Electrocatalysis of formic acid on palladium and platinum surfaces: from fundamental mechanisms to fuel cell applications.

    Science.gov (United States)

    Jiang, Kun; Zhang, Han-Xuan; Zou, Shouzhong; Cai, Wen-Bin

    2014-10-14

    Formic acid as a natural biomass and a CO2 reduction product has attracted considerable interest in renewable energy exploitation, serving as both a promising candidate for chemical hydrogen storage material and a direct fuel for low temperature liquid fed fuel cells. In addition to its chemical dehydrogenation, formic acid oxidation (FAO) is a model reaction in the study of electrocatalysis of C1 molecules and the anode reaction in direct formic acid fuel cells (DFAFCs). Thanks to a deeper mechanistic understanding of FAO on Pt and Pd surfaces brought about by recent advances in the fundamental investigations, the "synthesis-by-design" concept has become a mainstream idea to attain high-performance Pt- and Pd-based nanocatalysts. As a result, a large number of efficient nanocatalysts have been obtained through different synthesis strategies by tailoring geometric and electronic structures of the two primary catalytic metals. In this paper, we provide a brief overview of recent progress in the mechanistic studies of FAO, the synthesis of novel Pd- and Pt-based nanocatalysts as well as their practical applications in DFAFCs with a focus on discussing studies significantly contributing to these areas in the past five years.

  4. A Continuous Liquid-Level Sensor for Fuel Tanks Based on Surface Plasmon Resonance.

    Science.gov (United States)

    Pozo, Antonio M; Pérez-Ocón, Francisco; Rabaza, Ovidio

    2016-05-19

    A standard problem in large tanks at oil refineries and petrol stations is that water and fuel usually occupy the same tank. This is undesirable and causes problems such as corrosion in the tanks. Normally, the water level in tanks is unknown, with the problems that this entails. We propose herein a method based on surface plasmon resonance (SPR) to detect in real time the interfaces in a tank which can simultaneously contain water, gasoline (or diesel) and air. The plasmonic sensor is composed of a hemispherical glass prism, a magnesium fluoride layer, and a gold layer. We have optimized the structural parameters of the sensor from the theoretical modeling of the reflectance curve. The sensor detects water-fuel and fuel-air interfaces and measures the level of each liquid in real time. This sensor is recommended for inflammable liquids because inside the tank there are no electrical or electronic signals which could cause explosions. The sensor proposed has a sensitivity of between 1.2 and 3.5 RIU(-1) and a resolution of between 5.7 × 10(-4) and 16.5 × 10(-4) RIU.

  5. A Continuous Liquid-Level Sensor for Fuel Tanks Based on Surface Plasmon Resonance

    Science.gov (United States)

    Pozo, Antonio M.; Pérez-Ocón, Francisco; Rabaza, Ovidio

    2016-01-01

    A standard problem in large tanks at oil refineries and petrol stations is that water and fuel usually occupy the same tank. This is undesirable and causes problems such as corrosion in the tanks. Normally, the water level in tanks is unknown, with the problems that this entails. We propose herein a method based on surface plasmon resonance (SPR) to detect in real time the interfaces in a tank which can simultaneously contain water, gasoline (or diesel) and air. The plasmonic sensor is composed of a hemispherical glass prism, a magnesium fluoride layer, and a gold layer. We have optimized the structural parameters of the sensor from the theoretical modeling of the reflectance curve. The sensor detects water-fuel and fuel-air interfaces and measures the level of each liquid in real time. This sensor is recommended for inflammable liquids because inside the tank there are no electrical or electronic signals which could cause explosions. The sensor proposed has a sensitivity of between 1.2 and 3.5 RIU−1 and a resolution of between 5.7 × 10−4 and 16.5 × 10−4 RIU. PMID:27213388

  6. A Continuous Liquid-Level Sensor for Fuel Tanks Based on Surface Plasmon Resonance

    Directory of Open Access Journals (Sweden)

    Antonio M. Pozo

    2016-05-01

    Full Text Available A standard problem in large tanks at oil refineries and petrol stations is that water and fuel usually occupy the same tank. This is undesirable and causes problems such as corrosion in the tanks. Normally, the water level in tanks is unknown, with the problems that this entails. We propose herein a method based on surface plasmon resonance (SPR to detect in real time the interfaces in a tank which can simultaneously contain water, gasoline (or diesel and air. The plasmonic sensor is composed of a hemispherical glass prism, a magnesium fluoride layer, and a gold layer. We have optimized the structural parameters of the sensor from the theoretical modeling of the reflectance curve. The sensor detects water-fuel and fuel-air interfaces and measures the level of each liquid in real time. This sensor is recommended for inflammable liquids because inside the tank there are no electrical or electronic signals which could cause explosions. The sensor proposed has a sensitivity of between 1.2 and 3.5 RIU−1 and a resolution of between 5.7 × 10−4 and 16.5 × 10−4 RIU.

  7. In situ measurement of active catalyst surface area in fuel cell stacks

    Science.gov (United States)

    Brightman, E.; Hinds, G.; O'Malley, R.

    2013-11-01

    Measurement of electrochemical surface area (ECSA) of fuel cell electrodes is a key diagnostic of performance and gives a useful parameter for monitoring degradation and state of health in polymer electrolyte membrane fuel cells (PEMFCs). However, conventional methods for determining ECSA require potentiostatic control of the cell, which is impractical in a fuel cell stack. Here we demonstrate for the first time the practical application of a galvanostatic technique that enables in situ monitoring of ECSA in each cell throughout the lifetime of a stack. The concept is demonstrated at single cell level using both H adsorption and CO stripping, and the H adsorption (cathodic current) method is extended to stack testing. The undesirable effects of H2 crossover on the measurement may be minimised by appropriate selection of current density and by working with dilute H2 on the anode electrode. Good agreement is achieved with ECSA values determined using conventional single cell voltammetry across a range of MEA designs. The technique is straightforward to implement and provides an invaluable tool for state of health monitoring during PEMFC stack lifetime studies.

  8. Analytical estimation of control rod shadowing effect for excess reactivity measurement of High Temperature Engineering Test Reactor (HTTR)

    Energy Technology Data Exchange (ETDEWEB)

    Nakano, Masaaki; Yamashita, Kiyonobu; Fujimoto, Nozomu; Nojiri, Naoki; Takeuchi, Mitsuo; Fujisaki, Shingo [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Tokuhara, Kazumi; Nakata, Tetsuo

    1998-05-01

    The control rod shadowing effect has been estimated analytically in application of the fuel addition method to excess reactivity measurement of High Temperature Engineering Test Reactor (HTTR). The movements of control rods in the procedure of the fuel addition method have been simulated in the analysis. The calculated excess reactivity obtained by the simulation depends on the combinations of measuring control rods and compensating control rods and varies from -10% to +50% in comparison with the excess reactivity calculated from the effective multiplication factor of the core where all control rods are fully withdrawn. The control rod shadowing effect is reduced by the use of plural number of measuring and compensation control rods because of the reduction in neutron flux deformation in the measuring procedure. As a result, following combinations of control rods are recommended; 1) Thirteen control rods of the center, first, and second rings will be used for the reactivity measurement. The reactivity of each control rod is measured by the use of the other twelve control rods for reactivity compensation. 2) Six control rods of the first ring will be used for the reactivity measurement. The reactivity of each control rod is measured by the use of the other five control rods for reactivity compensation. (author)

  9. Ignition probability of fine dead surface fuels of native Patagonian forests or Argentina

    Directory of Open Access Journals (Sweden)

    Lucas O. Bianchi

    2014-04-01

    Full Text Available Aim of study: The Canadian Forest Fire Weather Index (FWI is being implemented all over the world. This index is being adapted to the Argentinean ecosystems since the year 2000. With the objective of calibrating the Fine Fuel Moisture Code (FFMC of the FWI system to Patagonian forests, we studied the relationship between ignition probability and fine dead surface fuel moisture content (MC as an indicator of potential fire ignition.Area of study: The study area is located in northwestern Patagonia, Argentina, and comprised two main forest types (cypress and ñire grown under a Mediterranean climate, with a dry summer and precipitations during winter and autumn (~500-800 mm per year.Material and Methods: We conducted lab ignition tests fires to determine the threshold of fine dead fuel ignition at different MC levels. Moisture content of dead fine surface fuels in the field was measured every 10-15 days from November to March for three seasons. We calculated the FFMC during these seasons and correlated it with the measured MC by applying a logistic regression model. We combined the results of the ignition tests and of the regressions to suggest FFMC categories for estimating fire danger in Patagonian forests.Main results: The ignition threshold occurred at MC values of 21.5 and 25.0% for cypress and ñire sites, respectively. The MC measured varied from 7.3 to 129.6%, and the calculated FFMC varied between 13.4 and 92.6. Highly significant regressions resulted when FFMC was related to MC. The ignition threshold corresponded to a FFMC=85. We proposed to divide the FFMC scale in three fire danger categories: Low (FFMC≤85, High (8589.Research highlights: Our results provide a useful tool for predicting fire danger in these ecosystems, and are a contribution to the development of the Argentinean Fire Danger Rating and a reference for similar studies in other countries where the FWI is being implemented

  10. Surface strontium enrichment on highly active perovskites for oxygen electrocatalysis in solid oxide fuel cells

    KAUST Repository

    Crumlin, Ethan J.

    2012-01-01

    Perovskite oxides have high catalytic activities for oxygen electrocatalysis competitive to platinum at elevated temperatures. However, little is known about the oxide surface chemistry that influences the activity near ambient oxygen partial pressures, which hampers the design of highly active catalysts for many clean-energy technologies such as solid oxide fuel cells. Using in situ synchrotron-based, ambient pressure X-ray photoelectron spectroscopy to study the surface chemistry changes, we show that the coverage of surface secondary phases on a (001)-oriented La 0.8Sr 0.2CoO 3-δ (LSC) film becomes smaller than that on an LSC powder pellet at elevated temperatures. In addition, strontium (Sr) in the perovskite structure enriches towards the film surface in contrast to the pellet having no detectable changes with increasing temperature. We propose that the ability to reduce surface secondary phases and develop Sr-enriched perovskite surfaces of the LSC film contributes to its enhanced activity for O 2 electrocatalysis relative to LSC powder-based electrodes. © 2012 The Royal Society of Chemistry.

  11. Boiling performance and material robustness of modified surfaces with multi scale structures for fuel cladding development

    Energy Technology Data Exchange (ETDEWEB)

    Jo, HangJin; Kim, Jin Man [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784, Gyungbuk (Korea, Republic of); Yeom, Hwasung [Department of Nuclear Engineering and Engineering physics, UW-Madison, Madison, WI 53706, Unities States (United States); Lee, Gi Cheol [Department of Mechanical Engineering, POSTECH, Pohang 790-784, Gyungbuk (Korea, Republic of); Park, Hyun Sun, E-mail: hejsunny@postech.ac.kr [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784, Gyungbuk (Korea, Republic of); Kiyofumi, Moriyama; Kim, Moo Hwan [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784, Gyungbuk (Korea, Republic of); Sridharan, Kumar; Corradini, Michael [Department of Nuclear Engineering and Engineering physics, UW-Madison, Madison, WI 53706, Unities States (United States)

    2015-09-15

    Highlights: • We improved boiling performance and material robustness using surface modification. • We combined micro/millimeter post structures and nanoparticles with heat treatments. • Compactly-arranged micrometer posts had improved boiling performance. • CHF increased significantly due to capillary pumping by the deposited NP layers. • Sintering procedure increased mechanical strength of the NP coating surface. - Abstract: By regulating the geometrical characteristics of multi-scale structures and by adopting heat treatment for protective layer of nanoparticles (NPs), we improved critical heat flux (CHF), boiling heat transfer (BHT), and mechanical robustness of the modified surface. We fabricated 1-mm and 100-μm post structures and deposited NPs on the structured surface as a nano-scale structured layer and protective layer at the same time, then evaluated the CHF and BHT and material robustness of the modified surfaces. On the structured surfaces without NPs, the surface with compactly-arranged micrometer posts had improved CHF (118%) and BHT (41%). On the surface with structures on which NPs had been deposited, CHF increased significantly (172%) due to capillary pumping by the deposited NP layers. The heat treatment improved robustness of coating layer in comparison to the one of before heat treatment. In particular, low-temperature sintering increased the hardness of the modified surface by 140%. The increased mechanical strength of the NP coating is attributed to reduction in coating porosity during sintering. The combination of micrometer posts structures and sintered NP coating can increase the safety, efficiency and reliability of advanced nuclear fuel cladding.

  12. Impact of thicker cladding on the nuclear parameters of the NPP Krsko fuel

    Energy Technology Data Exchange (ETDEWEB)

    Kromar, Marjan, E-mail: marjan.kromar@ijs.s [Jozef Stefan Institute, Reactor Physics Department, Jamova 39, 1001 Ljubljana (Slovenia); Kurincic, Bojan [Nuclear Power Plant Krsko, Engineering Division, Nuclear Fuel and Reactor Core, Vrbina 12, 8270 Krsko (Slovenia)

    2011-04-15

    To make fuel rods more resistant to grid-to-rod fretting or other cladding penetration failures, the cladding thickness could be increased or strengthened. Implementation of thicker fuel rod cladding was evaluated for the NPP Krsko that uses 16 x 16 fuel design. Cladding thickness of the Westinghouse standard fuel design (STD) and optimized fuel design (OFA) is increased. The reactivity effect during the fuel burnup is determined. To obtain a complete realistic view of the fuel behaviour a typical, near equilibrium, 18-month fuel cycle is investigated. The most important nuclear core parameters such as critical boron concentrations, isothermal temperature coefficient and rod worth are determined and compared.

  13. High surface area graphite as alternative support for proton exchange membrane fuel cell catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira-Aparicio, P.; Folgado, M.A. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Avda. Complutense 22, E-28040 Madrid (Spain); Daza, L. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Avda. Complutense 22, E-28040 Madrid (Spain); Instituto de Catalisis y Petroleoquimica (CSIC), C/Marie Curie, 2 Campus de Cantoblanco, E-28049 Madrid (Spain)

    2009-07-01

    The suitability of a high surface area graphite (HSAG) as proton exchange membrane fuel cell (PEMFC) catalyst support has been evaluated and compared with that of the most popular carbon black: the Vulcan XC72. It has been observed that Pt is arranged on the graphite surface resulting in different structures which depend on the catalysts synthesis conditions. The influence that the metal particle size and the metal-support interaction exert on the catalysts degradation rate is analyzed. Temperature programmed oxidation (TPO) under oxygen containing streams has been shown to be a useful method to assess the resistance of PEMFC catalysts to carbon corrosion. The synthesized Pt/HSAG catalysts have been evaluated in single cell tests in the cathode catalytic layer. The obtained results show that HSAG can be a promising alternative to the traditionally used Vulcan XC72 carbon black when suitable catalysts synthesis conditions are used. (author)

  14. Role of microstructure and surface defects on the dissolution kinetics of CeO2, a UO2 fuel analogue.

    OpenAIRE

    Corkhill, C.L; Bailey, D. J.; Tocino, F.Y.; Stennett, M.C.; Miller, J. A.; Provis, J.P.; Travis, K.P.; Hyatt, N.C.

    2016-01-01

    The release of radionuclides from spent fuel in a geological disposal facility is controlled by the surface mediated dissolution of UO2 in groundwater. In this study we investigate the influence of reactive surface sites on the dissolution of a synthesised CeO2 analogue for UO2 fuel. Dissolution was performed on: CeO2 annealed at high temperature, which eliminated intrinsic surface defects (point defects and dislocations); CeO2-x annealed in inert and reducing atmospheres to induce oxygen vac...

  15. Large-scale Flow Pulsation in Tight Square Arrayed Rod Bundles of Nuclear Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae Hwan; Kim, Kyung Min; Cho, Hyung Hee [Yonsei University, Seoul (Korea, Republic of); Shin, Chang Hwan; In, Wang Kee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-05-15

    As a major component of modern nuclear reactor, the nuclear fuel rod bundles with liquid coolant have been studied by a lot of researchers to understand the flow structure between the fuel rods. Recently, rod arrays with much small pitch-to-diameter ratio have been being tried to increase performance of the nuclear reactor. The liquid coolant flowing axially through these small spaces between the rods is known to show some peculiar phenomena including large-scale, quasi-periodic flow pulsation. These flow pulsation phenomena dominate mixing process in the subchannels. Thus, precise understating of the flow structure is essential to predict thermal-hydraulic phenomena in nuclear rod bundles. In this present paper, the turbulent flow in tight square arrayed rod bundles is investigated with Hot-wire anemometry. Then, the measured velocity data are analyzed by using Fast Fourier Transform analysis to find characteristic frequency of the pulsation

  16. Light water reactor fuel analysis code FEMAXI-V (Ver.1)

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Motoe [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2000-09-01

    A light water fuel analysis code FEMAXI-V is an advanced version which has been produced by integrating FEMAXI-IV(Ver.2), high burn-up fuel code EXBURN-I, and a number of functional improvements and extensions, to predict fuel rod behavior in normal and transient (not accident) conditions. The present report describes in detail the basic theories and structure, models and numerical solutions applied, improvements and extensions, and the material properties adopted in FEMAXI-V(Ver.1). FEMAXI-V deals with a single fuel rod. It predicts thermal and mechanical response of fuel rod to irradiation, including FP gas release. The thermal analysis predicts rod temperature distribution on the basis of pellet heat generation, changes in pellet thermal conductivity and gap thermal conductance, (transient) change in surface heat transfer to coolant, using radial one-dimensional geometry. The heat generation density profile of pellet can be determined by adopting the calculated results of burning analysis code. The mechanical analysis performs elastic/plastic, creep and PCMI calculations by FEM. The FP gas release model calculates diffusion of FP gas atoms and accumulation in bubbles, release and increase in internal pressure of rod. In every analysis, it is possible to allow some materials properties and empirical equations to depend on the local burnup or heat flux, which enables particularly analysis of high burnup fuel behavior and boiling transient of BWR rod. In order to facilitate effective and wide-ranging application of the code, formats and methods of input/output of the code are also described, and a sample output in an actual form is included. (author)

  17. Morphoelastic rods. Part I: A single growing elastic rod

    KAUST Repository

    Moulton, D.E.

    2013-02-01

    A theory for the dynamics and statics of growing elastic rods is presented. First, a single growing rod is considered and the formalism of three-dimensional multiplicative decomposition of morphoelasticity is used to describe the bulk growth of Kirchhoff elastic rods. Possible constitutive laws for growth are discussed and analysed. Second, a rod constrained or glued to a rigid substrate is considered, with the mismatch between the attachment site and the growing rod inducing stress. This stress can eventually lead to instability, bifurcation, and buckling. © 2012 Elsevier Ltd. All rights reserved.

  18. Learning with Rods: One Account.

    Science.gov (United States)

    Cherry, Donald Esha

    This paper discusses one English as a Second Language (ESL) teacher's attempts to use cuisenaire rods as a language learning tool. Cuisenaire rods (sometimes called algebricks) vary in size from 1 x 1 x 10 centimeter sticks to 1 x 1 x 1 centimeter cubes, with each of the 10 sizes a different color. Although such rods have been used to teach…

  19. Considerations for sensitivity analysis, uncertainty quantification, and data assimilation for grid-to-rod fretting

    Energy Technology Data Exchange (ETDEWEB)

    Michael Pernice

    2012-10-01

    Grid-to-rod fretting is the leading cause of fuel failures in pressurized water reactors, and is one of the challenge problems being addressed by the Consortium for Advanced Simulation of Light Water Reactors to guide its efforts to develop a virtual reactor environment. Prior and current efforts in modeling and simulation of grid-to-rod fretting are discussed. Sources of uncertainty in grid-to-rod fretting are also described.

  20. Ignition probability of fine dead surface fuels in native Patagonia forests of Argentina

    Energy Technology Data Exchange (ETDEWEB)

    Bianchi, L.; Defosse, G. E.

    2014-06-01

    Aim of study: The Canadian Forest Fire Weather Index (FWI) is being implemented all over the world. This index is being adapted to the Argentinean ecosystems since the year 2000. With the objective of calibrating the Fine Fuel Moisture Code (FFMC) of the FWI system to Patagonian forests, we studied the relationship between ignition probability and fine dead surface fuel moisture content (MC) as an indicator of potential fire ignition. Area of study: The study area is located in northwestern Patagonia, Argentina, and comprised two main forest types (cypress and nire) grown under a Mediterranean climate, with a dry summer and precipitations during winter and autumn ({approx}500-800 mm per year). Material and methods: We conducted lab ignition tests fires to determine the threshold of fine dead fuel ignition at different MC levels. Moisture content of dead fine surface fuels in the field was measured every 10-15 days from November to March for three seasons. We calculated the FFMC during these seasons and correlated it with the measured MC by applying a logistic regression model. We combined the results of the ignition tests and of the regressions to suggest FFMC categories for estimating fire danger in Patagonian forests. Main results: The ignition threshold occurred at MC values of 21.5 and 25.0% for cypress and nire sites, respectively. The MC measured varied from 7.3 to 129.6%, and the calculated FFMC varied between 13.4 and 92.6. Highly significant regressions resulted when FFMC was related to MC. The ignition threshold corresponded to a FFMC = 85. We proposed to divide the FFMC scale in three fire danger categories: Low (FFMC {<=} 85), High (85 < FFMC{<=}89) and Extreme (FFMC > 89). Research highlights: Our results provide a useful tool for predicting fire danger in these ecosystems, and are a contribution to the development of the Argentinean Fire Danger Rating and a reference for similar studies in other countries where the FWI is being implemented. (Author)

  1. A comparison of five sampling techniques to estimate surface fuel loading in montane forests

    Science.gov (United States)

    Pamela G. Sikkink; Robert E. Keane

    2008-01-01

    Designing a fuel-sampling program that accurately and efficiently assesses fuel load at relevant spatial scales requires knowledge of each sample method's strengths and weaknesses.We obtained loading values for six fuel components using five fuel load sampling techniques at five locations in western Montana, USA. The techniques included fixed-area plots, planar...

  2. High temperature control rod assembly

    Energy Technology Data Exchange (ETDEWEB)

    Vollman, R.E.

    1991-12-24

    This patent describes a control rod assembly for use in nuclear reactor control. It comprises segments, each the segment being made of a graphite composite material, each the segment having a chamber for containing neutron-absorbing material, wherein the chamber compromises a hollow cylindrical sleeve having a first end formed with an opening for receiving the neutron-absorbing material, and having a second end formed with a sleeve bore and an outer sleeve surface; a cylindrical weight-bearing support post positioned substantially centrally of the sleeve, the support post having a first end formed as a ball surface portion and a second end formed as a ball surface portion and a second end formed as a shaft, the shaft being engageable with the sleeve bore for rigidly coupling the support post axially within the hollow sleeve, a hollow cylindrical collar having a socket lip portion correspondingly shaped to receive the ball surface portion of an adjacent support post, and having an inner surface for engaging the outer sleeve surface on the second end of the sleeve to rigidly couple the collar to the sleeve.

  3. Results of automatic system implementation for the friction control rods execution in Cofrentes nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Curiel, M. [Logistica y Acondicionamientos Industriales SAU, Sorolla Center, local 10, Av. de las Cortes Valencianas, 46015 Valencia (Spain); Palomo, M. J. [ISIRYM, Universidad Politecnica de Valencia, Camino de Vera s/n, Valencia (Spain); Urrea, M. [Iberdrola Generacion S. A., Central Nuclear Cofrentes, Carretera Almansa Requena s/n, 04662 Cofrentes, Valencia (Spain); Arnaldos, A., E-mail: m.curiel@lainsa.co [TITANIA Servicios Tecnologicos SL, Sorolla Center, local 10, Av. de las Cortes Valencianas No. 58, 46015 Valencia (Spain)

    2010-10-15

    The purpose of this presentation is to show the obtained results in Cofrentes nuclear power plant (Spain) of control rods Pcc/24 friction test procedure. In order to perform this, a control rod friction test system has been developed. Principally, this system consists on software and data acquisition hardware that obtains and analyzes the control rod pressure variation on which the test is being made. The Pcc/24 procedure objective is to detect an excessive friction in the control rod movement that could cause a control rod drive movement slower than usual. This test is necessary every time that an anomalous alteration is produced in the reactor core that could affect to a fuel rod, and it is executed before the time measure of control rods rapid scram test of the affected rods. This test has to be carried out to all the reactor control rods and takes valuable time during plant refuelling. So, by means of an automatic system to perform the test, we obtain an important time saving during refuelling. On the other hand, the on-line monitoring of the control rod insertion and changes in differential pressure, permits a control rod operation fast and safe validation. Moreover, an automatic individual report of every rod is generated by the system and a final global result report of the entire test developed in refuelling is generated. The mentioned reports can be attached directly to the procedure documents obtaining an office data processing important saving time. (Author)

  4. Results of automatic system implementation for the friction control rods execution in Cofrentes nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Palomo, M., E-mail: mpalomo@iqn.upv.es [Universidad Politecnica de Valencia (UPV) (Spain); Urrea, M., E-mail: matias.urrea@iberdrola.es [Iberdrola Generacion S.A. Valencia (Spain). C.N. Cofrentes; Curiel, M., E-mail: m.curiel@lainsa.com [Logistica y Acondicionamientos Industriales (LAINSA), Valencia (Spain); Arnaldos, A., E-mail: a.arnaldos@titaniast.com [TITANIA Servicios Teconologicos, Valencia (Spain)

    2011-07-01

    The purpose of this presentation is to show the obtained results in Cofrentes Nuclear Power Plant (Spain) of Control Rods PCC/24 Friction Test Procedure. In order to perform this, a Control Rod Friction Test System has been developed. Principally, this system consists on software and data acquisition hardware that obtains and analyzes the control rod pressure variation on which the test is being made. The PCC/24 Procedure objective is to detect an excessive friction in the control rod movement that could cause a CRD (Control Rod Drive) movement slower than usual. This test is necessary every time that an anomalous alteration is produced in the reactor core that could affect to a fuel rod, and it is executed before the time measure of control rods rapid scram test of the affected rods. This test has to be carried out to all the reactor control rods and takes valuable time during plant refuelling. So, by means of an automatic system to perform the test, we obtain an important time saving during refuelling. On the other hand, the on-line monitoring of the control rod insertion and changes in differential pressure, permits a control rod operation fast and safe validation. Moreover, an automatic individual report of every rod is generated by the system and a final global result report of the entire test developed in refuelling is generated. The mentioned reports can be attached directly to the procedure documents obtaining an office data processing important saving time.(author)

  5. Thermal breeder fuel enrichment zoning

    Science.gov (United States)

    Capossela, Harry J.; Dwyer, Joseph R.; Luce, Robert G.; McCoy, Daniel F.; Merriman, Floyd C.

    1992-01-01

    A method and apparatus for improving the performance of a thermal breeder reactor having regions of higher than average moderator concentration are disclosed. The fuel modules of the reactor core contain at least two different types of fuel elements, a high enrichment fuel element and a low enrichment fuel element. The two types of fuel elements are arranged in the fuel module with the low enrichment fuel elements located between the high moderator regions and the high enrichment fuel elements. Preferably, shim rods made of a fertile material are provided in selective regions for controlling the reactivity of the reactor by movement of the shim rods into and out of the reactor core. The moderation of neutrons adjacent the high enrichment fuel elements is preferably minimized as by reducing the spacing of the high enrichment fuel elements and/or using a moderator having a reduced moderating effect.

  6. Simulation on the HTTR Control Rod Withdrawal Test

    Energy Technology Data Exchange (ETDEWEB)

    Jun, Ji Su; Tak, Nam-il; Lim, Hong Sik [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    This paper describes the GAMMA+ code simulation of HTTR control rod withdrawal test. The simulation is done to examine the effect of GAMMA+ code's single-zone and multi-zone point kinetics models on the prediction of the reactor power response during HTTR control rod withdrawal test. In addition, it has an objective to examine how the reactor power response is affected by the application of the fuel temperature coefficients on TRISO kernel or compact rod. The calculation results of reactivity response and reactor power response are compared with the test results which were obtained at the initial power of 15.2 MW with the amount of reactivity insertion by control rod withdrawal to 3.4e-04 (dk/k) in 6.59 seconds. All GAMMA+ simulation results on a HTTR CRW test showed good predictions with the measured data. In particular, TRISO Kernel Model where the fuel temperature coefficients applied on the TRISO particle produced a better prediction within a 1.5% measured data and made no difference between the single-zone model and the multi-zone point kinetics model. During the control rod withdrawal event which is a fast transient, the total reactivity is mainly affected by the inserted reactivity and the reactivity response due to the change of the fuel temperature and the graphite moderator temperature.

  7. Tungsten carbide modified high surface area carbon as fuel cell catalyst support

    Science.gov (United States)

    Shao, Minhua; Merzougui, Belabbes; Shoemaker, Krista; Stolar, Laura; Protsailo, Lesia; Mellinger, Zachary J.; Hsu, Irene J.; Chen, Jingguang G.

    Phase pure WC nanoparticles were synthesized on high surface area carbon black (800 m 2 g -1) by a temperature programmed reaction (TPR) method. The particle size of WC can be controlled under 30 nm with a relatively high coverage on the carbon surface. The electrochemical testing results demonstrated that the corrosion resistance of carbon black was improved by 2-fold with a surface modification by phase pure WC particles. However, the WC itself showed some dissolution under potential cycling. Based on the X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis, most of the WC on the surface was lost or transformed to oxides after 5000 potential cycles in the potential range of 0.65-1.2 V. The Pt catalyst supported on WC/C showed a slightly better ORR activity than that of Pt/C, with the Pt activity loss rate for Pt/WC/C being slightly slower compared to that of Pt/C. The performance and decay rate of Pt/WC/C were also evaluated in a fuel cell.

  8. Design requirement on KALIMER control rod assembly duct

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, W.; Kang, H. Y.; Nam, C.; Kim, J. O.; Kim, Y. J

    1998-03-01

    This document establishes the design guidelines which are needs for designing the control rod assembly duct of the KALIMER as design requirements. it describes control rod assembly duct of the KALIMER and its requirements that includes functional requirements, performance requirements, interfacing systems, design limits and strength requirements, seismic requirements, structural requirements, environmental requirements, reliability and safety requirements, standard and codes, QA programs, and other requirements. The control rod system consists of three parts, which are drive mechanism, drive-line, and absorber bundle. This report deals with the absorber bundle and its outer duct only because the others are beyond the scope of fuel system design. The guidelines for design requirements intend to be used for an improved design of the control rod assembly duct of the KALIMER. (author). 19 refs.

  9. Safety rod latch inspection

    Energy Technology Data Exchange (ETDEWEB)

    Leader, D.R.

    1992-02-01

    During an attempt to raise control rods from the 100 K reactor in December, one rod could not be withdrawn. Subsequent investigation revealed that a small button'' in the latch mechanism had broken off of the lock plunger'' and was wedged in a position that prevented rod withdrawal. Concern that this failure may have resulted from corrosion or some other metallurgical problem resulted in a request that SRL examine six typical latch mechanisms from the 100 L reactor by use of radiography and metallography. During the examination of the L-Area latches, a failed latch mechanism from the 100 K reactor was added to the investigation. Fourteen latches that had a history of problems were removed from K-Area and sent to SRL for inclusion in this study the week after the original seven assemblies were examined, bringing the total of latch assemblies discussed in this report to twenty one. Results of the examination of the K-Area latch that initiated this study is not included in this report.

  10. Safety rod latch inspection

    Energy Technology Data Exchange (ETDEWEB)

    Leader, D.R.

    1992-02-01

    During an attempt to raise control rods from the 100 K reactor in December, one rod could not be withdrawn. Subsequent investigation revealed that a small ``button`` in the latch mechanism had broken off of the ``lock plunger`` and was wedged in a position that prevented rod withdrawal. Concern that this failure may have resulted from corrosion or some other metallurgical problem resulted in a request that SRL examine six typical latch mechanisms from the 100 L reactor by use of radiography and metallography. During the examination of the L-Area latches, a failed latch mechanism from the 100 K reactor was added to the investigation. Fourteen latches that had a history of problems were removed from K-Area and sent to SRL for inclusion in this study the week after the original seven assemblies were examined, bringing the total of latch assemblies discussed in this report to twenty one. Results of the examination of the K-Area latch that initiated this study is not included in this report.

  11. Fuel moisture content estimation: a land-surface modelling approach applied to African savannas

    Science.gov (United States)

    Ghent, D.; Spessa, A.; Kaduk, J.; Balzter, H.

    2009-04-01

    Despite the importance of fire to the global climate system, in terms of emissions from biomass burning, ecosystem structure and function, and changes to surface albedo, current land-surface models do not adequately estimate key variables affecting fire ignition and propagation. Fuel moisture content (FMC) is considered one of the most important of these variables (Chuvieco et al., 2004). Biophysical models, with appropriate plant functional type parameterisations, are the most viable option to adequately predict FMC over continental scales at high temporal resolution. However, the complexity of plant-water interactions, and the variability associated with short-term climate changes, means it is one of the most difficult fire variables to quantify and predict. Our work attempts to resolve this issue using a combination of satellite data and biophysical modelling applied to Africa. The approach we take is to represent live FMC as a surface dryness index; expressed as the ratio between the Normalised Difference Vegetation Index (NDVI) and land-surface temperature (LST). It has been argued in previous studies (Sandholt et al., 2002; Snyder et al., 2006), that this ratio displays a statistically stronger correlation to FMC than either of the variables, considered separately. In this study, simulated FMC is constrained through the assimilation of remotely sensed LST and NDVI data into the land-surface model JULES (Joint-UK Land Environment Simulator). Previous modelling studies of fire activity in Africa savannas, such as Lehsten et al. (2008), have reported significant levels of uncertainty associated with the simulations. This uncertainty is important because African savannas are among some of the most frequently burnt ecosystems and are a major source of greenhouse trace gases and aerosol emissions (Scholes et al., 1996). Furthermore, regional climate model studies indicate that many parts of the African savannas will experience drier and warmer conditions in future

  12. In-situ electrochemically active surface area evaluation of an open-cathode polymer electrolyte membrane fuel cell stack

    Science.gov (United States)

    Torija, Sergio; Prieto-Sanchez, Laura; Ashton, Sean J.

    2016-09-01

    The ability to evaluate the electrochemically active surface area (ECSA) of fuel cell electrodes is crucial toward characterising designs and component suites in-situ, particularly when evaluating component durability in endurance testing, since it is a measure of the electrode area available to take part in the fuel cell reactions. Conventional methods to obtain the ECSA using cyclic voltammetry, however, rely on potentiostats that cannot be easily scaled to simultaneously evaluate all cells in a fuel cell stack of practical size, which is desirable in fuel cell development. In-situ diagnostics of an open-cathode fuel cell stack are furthermore challenging because the cells do not each possess an enclosed cathode compartment; instead, the cathodes are rather open to the environment. Here we report on a diagnostic setup that allows the electrochemically active surface area of each cell anode or cathode in an open-cathode fuel cell stack to be evaluated in-situ and simultaneously, with high resolution and reproducibility, using an easily scalable chronopotentiometry methodology and a gas-tight stack enclosure.

  13. Surface characterization of adsorbents in ultrasound-assisted oxidative desulfurization process of fossil fuels.

    Science.gov (United States)

    Etemadi, Omid; Yen, Teh Fu

    2007-09-01

    Surface properties of two different phases of alumina were studied through SEM images. Characterization of amorphous acidic alumina and crystalline boehmite by XRD explains the differences in adsorption capacities of each sample. Data from small angle neutron scattering (SANS) provide further results regarding the ordering in amorphous and crystalline samples of alumina. Quantitative measurements from SANS are used for pore size calculations. Higher disorder provides more topological traps, irregularities, and hidden grooves for higher adsorption capacity. An isotherm model was derived for adsorption of dibenzothiophene sulfone (DBTO) by amorphous acidic alumina to predict and calculate the adsorption of sulfur compounds. The Langmuir-Freundlich model covers a wide range of sulfur concentrations. Experiments prove that amorphous acidic alumina is the adsorbent of choice for selective adsorption in the ultrasound-assisted oxidative desulfurization (UAOD) process to produce ultra-low-sulfur fuel (ULSF).

  14. Dependence of the specific surface area of the nuclear fuel with the matrix oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, F.; Quinones, J.; Iglesias, E.; Rodriguez, N. [CIEMAT. Avda. Complutense 22, 28040-Madrid (Spain)

    2008-07-01

    This paper is focused on the study of the changes in the specific surface area measured using BET techniques. The objective is to obtain a relation between this parameter and the change in the matrix stoichiometry (i.e., oxidation increase). None of the actual models used for extrapolating the behaviour of the spent fuel matrix under repository conditions have included this dependence yet. In this work the specific surface area of different uranium oxide were measured using N{sub 2}(g) and Kr(g). The starting material was UO{sub 2+x}(s) with a size powder distribution lower than 20 {mu}m. The results included in this paper shown a strong dependence on specific surface area with the matrix stoichiometry, i.e., and increase of more than one order of magnitude (SUO{sub 2} = 6 m{sup 2}*g{sup -1} and SU{sub 3}O{sub 8} = 16.07 m{sup 2}*g{sup -1}). Furthermore, the particle size distribution measured as a function of the thermal treatment done shows changes on the powder size related to the changes observed in the uranium oxide stoichiometry. (authors)

  15. Oligo(naphthylene–ethynylene) Molecular Rods

    DEFF Research Database (Denmark)

    Cramer, Jacob Roland; Ning, Yanxiao; Shen, Cai;

    2013-01-01

    Molecular rods designed for surface chirality studies have been synthesized in high yields. The molecules are composed of oligo(naphthylene–ethynylene) skeletons and functionalized at their two termini with carboxylic acids and hydrophobic groups. The molecular skeletons were constructed by means...... of palladium-catalyzed Sonogashira reactions between naphthyl halides and acetylenes. The triazene functionality was used as a protected iodine precursor to allow linear extension of the molecular rods during the synthe-ses. The carboxylic acid groups in the target molecules were protected as esters during...... the synthesis to keep the large aromatic molecules soluble during their syntheses. These rigid oligomers were designed to form lamella-like structures when adsorbed on a surface, through which multiple distinguishable surface conformations should be obtainable. Preliminary scanning tunneling microscopy imaging...

  16. Super-energy-saving dewatering method for high-specific-surface-area fuels by using dimethyl ether

    Energy Technology Data Exchange (ETDEWEB)

    Kanda, H. [Central Research Institute for Electric Power Industry, Kanagawa (Japan)

    2008-07-01

    There is a growing need for the economical dewatering of high-specific-surface-area fuels containing large amounts of water, such as coal and sewage sludge. The principle underlying conventional dewatering methods is evaporation of the water content by heating the fuels to a high temperature, but this approach consumes a considerable amount of energy. The Central Research Institute of the Electric Power Industry (CRIEPI) has developed a method for the extraction of this water through the use of dimethyl ether (DME), which liquefies at ordinary temperatures under the influence of a slight pressure. In this method, the water content in the fuel is extracted into the liquefied DME for separation from the fuel. After dewatering, the DME is depressurised, and subsequently vaporised, thereby leaving the separated water. Dewatering with an input energy of only 1109 kJ/kg water under ordinary conditions has been demonstrated theoretically.

  17. Semiconductor Quantum Rods as Single Molecule FluorescentBiological Labels

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Aihua; Gu, Weiwei; Boussert, Benjamine; Koski, Kristie; Gerion, Daniele; Manna, Liberato; Le Gros, Mark; Larabell, Carolyn; Alivisatos, A. Paul

    2006-05-29

    In recent years, semiconductor quantum dots have beenapplied with great advantage in a wide range of biological imagingapplications. The continuing developments in the synthesis of nanoscalematerials and specifically in the area of colloidal semiconductornanocrystals have created an opportunity to generate a next generation ofbiological labels with complementary or in some cases enhanced propertiescompared to colloidal quantum dots. In this paper, we report thedevelopment of rod shaped semiconductor nanocrystals (quantum rods) asnew fluorescent biological labels. We have engineered biocompatiblequantum rods by surface silanization and have applied them fornon-specific cell tracking as well as specific cellular targeting. Theproperties of quantum rods as demonstrated here are enhanced sensitivityand greater resistance for degradation as compared to quantum dots.Quantum rods have many potential applications as biological labels insituations where their properties offer advantages over quantumdots.

  18. Jourdain Principle of a Super-Thin Elastic Rod Dynamics

    Institute of Scientific and Technical Information of China (English)

    XUE Yun; SHANG Hui-Lin

    2009-01-01

    A super thin elastic rod is modeled with a background of DNA super coiling structure, and its dynamics is discussed based on the Jourdain variation. The cross section of the rod is taken as the object of this study and two velocity spaces about arc coordinate and the time are obtained respectively. Virtual displacements of the section on the two velocity spaces are defined and can be expressed in terms of Jourdaln variation. Jourdain principles of a super thin elastic rod dynamics on arc coordinate and the time velocity space are established,respectively, which show that there are two ways to realize the constraint conditions. If the constitutive relation of the rod is linear, the Jourdaln principle takes the Euler-Lagrange form with generalized coordinates. The Kirchhoff equation, Lagrange equation and Appell equation can be derived from the present Jourdaln principle.While the rod subjected to a surface constraint, Lagrange equation with undetermined multipliers may be derived.

  19. The coupling effect of gas-phase chemistry and surface reactions on oxygen permeation and fuel conversion in ITM reactors

    KAUST Repository

    Hong, Jongsup

    2015-08-01

    © 2015 Elsevier B.V. The effect of the coupling between heterogeneous catalytic reactions supported by an ion transport membrane (ITM) and gas-phase chemistry on fuel conversion and oxygen permeation in ITM reactors is examined. In ITM reactors, thermochemical reactions take place in the gas-phase and on the membrane surface, both of which interact with oxygen permeation. However, this coupling between gas-phase and surface chemistry has not been examined in detail. In this study, a parametric analysis using numerical simulations is conducted to investigate this coupling and its impact on fuel conversion and oxygen permeation rates. A thermochemical model that incorporates heterogeneous chemistry on the membrane surface and detailed chemical kinetics in the gas-phase is used. Results show that fuel conversion and oxygen permeation are strongly influenced by the simultaneous action of both chemistries. It is shown that the coupling somewhat suppresses the gas-phase kinetics and reduces fuel conversion, both attributed to extensive thermal energy transfer towards the membrane which conducts it to the air side and radiates to the reactor walls. The reaction pathway and products, in the form of syngas and C2 hydrocarbons, are also affected. In addition, the operating regimes of ITM reactors in which heterogeneous- or/and homogeneous-phase reactions predominantly contribute to fuel conversion and oxygen permeation are elucidated.

  20. Metrology Determination in hot cell of spent nuclear fuel

    Energy Technology Data Exchange (ETDEWEB)

    Eom, Sung Ho; Min, D.K.; Kim, E.K.; Hwang, Y.H.; Lee, H.G.; You, G.S.; Koo, G.S.; Koo, D.S.; Hong, S.B

    1999-03-01

    The defects and dimensional changes of irradiated fuel rods are due to several causes during the operation of reactor. The severity of dimensional changes might bring trouble in reactor operation. The dimensional data such as diameter changes and length changes of irradiated fuel rods are invaluable to designs of fuel rods and integrity evaluation of fuel rods. In this report, the standard gauges for measuring the dimensional changes of fuel rods are manufactured. The development of profilometry examination technology enabled motor control system using personal computer to measure diameter on each occasion 0.01 mm in length of irradiated fuel rods. By programming the process of profilometry examination, the measuring data of the dimensional changes can be stored and analyzed with personal computer. (Author). 4 refs., 5 tabs., 18 figs.

  1. Cone rod dystrophies

    Directory of Open Access Journals (Sweden)

    Hamel Christian P

    2007-02-01

    Full Text Available Abstract Cone rod dystrophies (CRDs (prevalence 1/40,000 are inherited retinal dystrophies that belong to the group of pigmentary retinopathies. CRDs are characterized by retinal pigment deposits visible on fundus examination, predominantly localized to the macular region. In contrast to typical retinitis pigmentosa (RP, also called the rod cone dystrophies (RCDs resulting from the primary loss in rod photoreceptors and later followed by the secondary loss in cone photoreceptors, CRDs reflect the opposite sequence of events. CRD is characterized by primary cone involvement, or, sometimes, by concomitant loss of both cones and rods that explains the predominant symptoms of CRDs: decreased visual acuity, color vision defects, photoaversion and decreased sensitivity in the central visual field, later followed by progressive loss in peripheral vision and night blindness. The clinical course of CRDs is generally more severe and rapid than that of RCDs, leading to earlier legal blindness and disability. At end stage, however, CRDs do not differ from RCDs. CRDs are most frequently non syndromic, but they may also be part of several syndromes, such as Bardet Biedl syndrome and Spinocerebellar Ataxia Type 7 (SCA7. Non syndromic CRDs are genetically heterogeneous (ten cloned genes and three loci have been identified so far. The four major causative genes involved in the pathogenesis of CRDs are ABCA4 (which causes Stargardt disease and also 30 to 60% of autosomal recessive CRDs, CRX and GUCY2D (which are responsible for many reported cases of autosomal dominant CRDs, and RPGR (which causes about 2/3 of X-linked RP and also an undetermined percentage of X-linked CRDs. It is likely that highly deleterious mutations in genes that otherwise cause RP or macular dystrophy may also lead to CRDs. The diagnosis of CRDs is based on clinical history, fundus examination and electroretinogram. Molecular diagnosis can be made for some genes, genetic counseling is

  2. Site-specific growth of polymers on silica rods.

    Science.gov (United States)

    Peng, Bo; Soligno, Giuseppe; Kamp, Marlous; de Nijs, Bart; de Graaf, Joost; Dijkstra, Marjolein; van Roij, René; van Blaaderen, Alfons; Imhof, Arnout

    2014-12-28

    Colloids specifically developed for self-assembly (SA) into advanced functional materials have rapidly become more complex, as this complexity allows for more ways to optimize both the SA process and the properties of the resulting materials. For instance, by creating 'patchy' particles more open structures can be achieved through directional interactions. However, the number of ways in which site-specific chemistry can be achieved on particle surfaces is still limited. Here, we show how polymer patches can be specifically grown onto only the flat end of bullet-shaped silica rods by utilizing a subtle anisotropy in surface tension and shape caused by the growth mechanism of the rods. Conversely, if the bullet-shaped silica rods are used as 'Pickering-emulsion' stabilizers the same surface tension effects exclusively direct the orientation of the rods into a 'hedgehog-morphology'. Finally, we demonstrate how an external electric field can direct the particles in a 'vectorial' way.

  3. Switch isotropic/anisotropic wettability via dual-scale rods

    Directory of Open Access Journals (Sweden)

    Yang He

    2014-10-01

    Full Text Available It is the first time to demonstrate the comparison of isotropic/anisotropic wettability between dual-scale micro-nano-rods and single-scale micro-rods. Inspired by the natural structures of rice leaf, a series of micro-nano-rods and micro-rods with different geometric parameters were fabricated using micro-fabrication technology. Experimental measured apparent contact angles and advancing and receding contact angles from orthogonal orientations were characterized. The difference of contact angles from orthogonal orientation on dual-scale rods was much smaller than those on single-scale rods in both static and dynamic situation. It indicated that the dual-scale micro-nano-rods showed isotropic wettability, while single-scale micro-rods showed anisotropic wettability. The switch of isotropic/anisotropic wettability could be illustrated by different wetting state and contact line moving. It offers a facial way to switch isotropic/anisotropic wettability of the surface via dual-scale or single-scale structure.

  4. Switch isotropic/anisotropic wettability via dual-scale rods

    Science.gov (United States)

    He, Yang; Jiang, Chengyu; Wang, Shengkun; Ma, Zhibo; Yuan, Weizheng

    2014-10-01

    It is the first time to demonstrate the comparison of isotropic/anisotropic wettability between dual-scale micro-nano-rods and single-scale micro-rods. Inspired by the natural structures of rice leaf, a series of micro-nano-rods and micro-rods with different geometric parameters were fabricated using micro-fabrication technology. Experimental measured apparent contact angles and advancing and receding contact angles from orthogonal orientations were characterized. The difference of contact angles from orthogonal orientation on dual-scale rods was much smaller than those on single-scale rods in both static and dynamic situation. It indicated that the dual-scale micro-nano-rods showed isotropic wettability, while single-scale micro-rods showed anisotropic wettability. The switch of isotropic/anisotropic wettability could be illustrated by different wetting state and contact line moving. It offers a facial way to switch isotropic/anisotropic wettability of the surface via dual-scale or single-scale structure.

  5. A genetically encoded reporter for real-time imaging of cofilin-actin rods in living neurons.

    Directory of Open Access Journals (Sweden)

    Jianjie Mi

    Full Text Available Filament bundles (rods of cofilin and actin (1:1 form in neurites of stressed neurons where they inhibit synaptic function. Live-cell imaging of rod formation is hampered by the fact that overexpression of a chimera of wild type cofilin with a fluorescent protein causes formation of spontaneous and persistent rods, which is exacerbated by the photostress of imaging. The study of rod induction in living cells calls for a rod reporter that does not cause spontaneous rods. From a study in which single cofilin surface residues were mutated, we identified a mutant, cofilinR21Q, which when fused with monomeric Red Fluorescent Protein (mRFP and expressed several fold above endogenous cofilin, does not induce spontaneous rods even during the photostress of imaging. CofilinR21Q-mRFP only incorporates into rods when they form from endogenous proteins in stressed cells. In neurons, cofilinR21Q-mRFP reports on rods formed from endogenous cofilin and induced by all modes tested thus far. Rods have a half-life of 30-60 min upon removal of the inducer. Vesicle transport in neurites is arrested upon treatments that form rods and recovers as rods disappear. CofilinR21Q-mRFP is a genetically encoded rod reporter that is useful in live cell imaging studies of induced rod formation, including rod dynamics, and kinetics of rod elimination.

  6. Computer simulation of rod-sphere mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Antypov, Dmytro

    2003-07-01

    Results are presented from a series of simulations undertaken to investigate the effect of adding small spherical particles to a fluid of rods which would otherwise represent a liquid crystalline (LC) substance. Firstly, a bulk mixture of Hard Gaussian Overlap particles with an aspect ratio of 3:1 and hard spheres with diameters equal to the breadth of the rods is simulated at various sphere concentrations. Both mixing-demixing and isotropic-nematic transition are studied using Monte Carlo techniques. Secondly, the effect of adding Lennard-Jones particles to an LC system modelled using the well established Gay-Berne potential is investigated. These rod-sphere mixtures are simulated using both the original set of interaction parameters and a modified version of the rod-sphere potential proposed in this work. The subject of interest is the internal structure of the binary mixture and its dependence on density, temperature, concentration and various parameters characterising the intermolecular interactions. Both the mixing-demixing behaviour and the transitions between the isotropic and any LC phases have been studied for four systems which differ in the interaction potential between unlike particles. A range of contrasting microphase separated structures including bicontinuous, cubic, and micelle-like arrangement have been observed in bulk. Thirdly, the four types of mixtures previously studied in bulk are subjected to a static magnetic field. A variety of novel phases are observed for the cases of positive and negative anisotropy in the magnetic susceptibility. These include a lamellar structure, in which layers of rods are separated by layers of spheres, and a configuration with a self-assembling hexagonal array of spheres. Finally, two new models are presented to study liquid crystal mixtures in the presence of curved substrates. These are implemented for the cases of convex and concave spherical surfaces. The simulation results obtained in these geometries

  7. Improve Design of Fuel Shear for Fast Reactor

    Institute of Scientific and Technical Information of China (English)

    GAO; Wei; OUYANG; Ying-gen; LI; Wei-min

    2012-01-01

    <正>Due to the deeper burnup and higher fuel swelling, fast reactor metal fuel rod using 316 stainless steel cladding, replacing the traditional zirconia cladding. The diameter of fuel rod of fast reactor is much longer than that of PWR, and the cladding of stainless steel has better ductility than zirconia cladding. Using the existing shear still will cause several aspects of problem: 1) Longer diameter of rod leads to

  8. Measurement of liquid film flow on nuclear rod bundle in micro-scale by using very high speed camera system

    Science.gov (United States)

    Pham, Son; Kawara, Zensaku; Yokomine, Takehiko; Kunugi, Tomoaki

    2012-11-01

    Playing important roles in the mass and heat transfer as well as the safety of boiling water reactor, the liquid film flow on nuclear fuel rods has been studied by different measurement techniques such as ultrasonic transmission, conductivity probe, etc. Obtained experimental data of this annular two-phase flow, however, are still not enough to construct the physical model for critical heat flux analysis especially at the micro-scale. Remain problems are mainly caused by complicated geometry of fuel rod bundles, high velocity and very unstable interface behavior of liquid and gas flow. To get over these difficulties, a new approach using a very high speed digital camera system has been introduced in this work. The test section simulating a 3×3 rectangular rod bundle was made of acrylic to allow a full optical observation of the camera. Image data were taken through Cassegrain optical system to maintain the spatiotemporal resolution up to 7 μm and 20 μs. The results included not only the real-time visual information of flow patterns, but also the quantitative data such as liquid film thickness, the droplets' size and speed distributions, and the tilt angle of wavy surfaces. These databases could contribute to the development of a new model for the annular two-phase flow. Partly supported by the Global Center of Excellence (G-COE) program (J-051) of MEXT, Japan.

  9. Influence of miscut on crystal truncation rod scattering

    Energy Technology Data Exchange (ETDEWEB)

    Munkholm, A.; Brennan, S. [Stanford Univ., CA (United States). Synchrotron Radiat. Lab.

    1999-04-01

    X-rays can be used to measure the roughness of a surface by the study of crystal truncation rod scattering. It is shown that for a simple cubic lattice the presence of a miscut surface with a regular step array has no effect on the scattered intensity of a single rod and that a distribution of terrace widths on the surface is shown to have the same effect as adding roughness to the surface. For a perfect crystal without miscut, the scattered intensity is the sum of the intensity from all the rods with the same in-plane momentum transfer. For all real crystals, the scattered intensity is better described as that from a single rod. It is shown that data-collection strategies must correctly account for the sample miscut or there is a potential for improperly measuring the rod intensity. This can result in an asymmetry in the rod intensity above and below the Bragg peak, which can be misinterpreted as being due to a relaxation of the surface. The calculations presented here are compared with data for silicon (001) wafers with 0.1 and 4 miscuts. (orig.) 22 refs.

  10. Nanoionics and Nanocatalysts: Conformal Mesoporous Surface Scaffold for Cathode of Solid Oxide Fuel Cells

    Science.gov (United States)

    Chen, Yun; Gerdes, Kirk; Song, Xueyan

    2016-09-01

    Nanoionics has become increasingly important in devices and systems related to energy conversion and storage. Nevertheless, nanoionics and nanostructured electrodes development has been challenging for solid oxide fuel cells (SOFCs) owing to many reasons including poor stability of the nanocrystals during fabrication of SOFCs at elevated temperatures. In this study, a conformal mesoporous ZrO2 nanoionic network was formed on the surface of La1‑xSrxMnO3/yttria-stabilized zirconia (LSM/YSZ) cathode backbone using Atomic Layer Deposition (ALD) and thermal treatment. The surface layer nanoionic network possesses open mesopores for gas penetration, and features a high density of grain boundaries for enhanced ion-transport. The mesoporous nanoionic network is remarkably stable and retains the same morphology after electrochemical operation at high temperatures of 650–800 °C for 400 hours. The stable mesoporous ZrO2 nanoionic network is further utilized to anchor catalytic Pt nanocrystals and create a nanocomposite that is stable at elevated temperatures. The power density of the ALD modified and inherently functional commercial cells exhibited enhancement by a factor of 1.5–1.7 operated at 0.8 V at 750 °C.

  11. In situ formation of graphene layers on graphite surfaces for efficient anodes of microbial fuel cells.

    Science.gov (United States)

    Tang, Jiahuan; Chen, Shanshan; Yuan, Yong; Cai, Xixi; Zhou, Shungui

    2015-09-15

    Graphene can be used to improve the performance of the anode in a microbial fuel cell (MFC) due to its good biocompatibility, high electrical conductivity and large surface area. However, the chemical production and modification of the graphene on the anode are environmentally hazardous because of the use of various harmful chemicals. This study reports a novel method based on the electrochemical exfoliation of a graphite plate (GP) for the in situ formation of graphene layers on the surface of a graphite electrode. When the resultant graphene-layer-based graphite plate electrode (GL/GP) was used as an anode in an MFC, a maximum power density of 0.67 ± 0.034 W/m(2) was achieved. This value corresponds to 1.72-, 1.56- and 1.26-times the maximum power densities of the original GP, exfoliated-graphene-modified GP (EG/GP) and chemically-reduced-graphene-modified GP (rGO/GP) anodes, respectively. Electrochemical measurements revealed that the high performance of the GL/GP anode was attributable to its macroporous structure, improved electron transfer and high electrochemical capacitance. The results demonstrated that the proposed method is a facile and environmentally friendly synthesis technique for the fabrication of high-performance graphene-based electrodes for use in microbial energy harvesting. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Active Brownian rods

    Science.gov (United States)

    Peruani, Fernando

    2016-11-01

    Bacteria, chemically-driven rods, and motility assays are examples of active (i.e. self-propelled) Brownian rods (ABR). The physics of ABR, despite their ubiquity in experimental systems, remains still poorly understood. Here, we review the large-scale properties of collections of ABR moving in a dissipative medium. We address the problem by presenting three different models, of decreasing complexity, which we refer to as model I, II, and III, respectively. Comparing model I, II, and III, we disentangle the role of activity and interactions. In particular, we learn that in two dimensions by ignoring steric or volume exclusion effects, large-scale nematic order seems to be possible, while steric interactions prevent the formation of orientational order at large scales. The macroscopic behavior of ABR results from the interplay between active stresses and local alignment. ABR exhibit, depending on where we locate ourselves in parameter space, a zoology of macroscopic patterns that ranges from polar and nematic bands to dynamic aggregates.

  13. Substitute safety rods: Physics of operation and irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, N.P.

    1991-11-18

    Under certain assumed accidents, an SRS reactor may lose most of its bulk moderator while maintaining flow to fuel assemblies. If this occurs immediately after operation at power, components normally dependent on convective heat transfer to the moderator will heat up with the possibility of melting that component. One component at risk is the currently used cadmium safety rod. A substitute safety rod consisting solely of sintered B{sub 4}C and stainless steel has been designed which is capable of withstanding much higher temperatures. This memorandum provides the physics basis for the adequacy of the rod for reactor shutdown and provides a set of criteria for acceptance in the NTG tests. This memorandum provides physics data for other aspects of operation. These include: Heat production and helium production, along with related phenomena, resulting from inadvertent irradiation at power. Gamma heat input under drained tank conditions. An equivalent rod design suitable for charge design and safety analyses. Degradation under normal operation. Thermal flux ripple in adjacent fuel due to axial striping of alternate B{sub 4}C and steel pellets. Possible effect on safety analyses. Safety rod withdrawal during reactor startup.

  14. Contribution of Energetically Reactive Surface Features to the Dissolution of CeO2 and ThO2 Analogues for Spent Nuclear Fuel Microstructures

    OpenAIRE

    Corkhill, C.; Myllykyla, E.; Bailey, D. J.; Thornber, S.M.; Qi, J.; Maldonado, P.; Stennett, M.C.; Hamilton, A.; Hyatt, N.C.

    2014-01-01

    In the safety case for the geological disposal of nuclear waste, the release of radioactivity from the repository is controlled by the dissolution of the spent fuel in groundwater. There remain several uncertainties associated with understanding spent fuel dissolution, including the contribution of energetically reactive surface sites to the dissolution rate. In this study, we investigate how surface features influence the dissolution rate of synthetic CeO2 and ThO2, spent nuclear fuel analog...

  15. The Role of Non-Conventional Supports for Single-Atom Platinum-Based Catalysts in Fuel-Cell Technology: A Theoretical Surface Science Approach

    Science.gov (United States)

    2013-02-05

    on the thermodynamic stability of platinized TiN. 15. SUBJECT TERMS fuel cells , Theoretical modeling , electrodes 16. SECURITY CLASSIFICATION OF...system are reported for various surface coverages of Pt. We find that atomic Pt does not bind preferably to the clean TiN surface, but under typical PEM ...could be a promising catalyst for PEM fuel cells. Introduction: Proton exchange membrane fuel cells (PEMFCs) have found wide potential

  16. Brownian rod scheme in microenvironment sensing

    Directory of Open Access Journals (Sweden)

    Ian Gralinski

    2012-03-01

    Full Text Available Fluctuations of freely translating spherical particles via Brownian motion should provide inexhaustible information about the micro-environment, but is beset by the problem of particles drifting away from the venue of measurement as well as colliding with other particles. We propose a scheme here to circumvent this in which a Brownian rod that lies in proximity to a cylindrical pillar is drawn in by a tuneable attractive force from the pillar. The force is assumed to act through the centre of each body and the motion exclusive to the x-y plane. Simulation studies show two distinct states, one in which the rod is moving freely (state I and the other in which the rod contacts the cylinder surface (state II. Information about the micro-environment could be obtained by tracking the rotational diffusion coefficient Dθ populating in either of these two states. However, the magnitude of the normalized charge product in excess of 6.3x104 was found necessary for a rod of 6.81 × 0.93 μm2 (length × diameter and 10μm diameter cylindrical pillar to minimize deviation errors. It was also found that the extent of spatial sensing coverage could be controlled by varying the charge level. The conditions needed to ascertain the rotational sampling for angle determination through the Hough transform were also discussed.

  17. Adjustable solitary waves in electroactive rods

    Science.gov (United States)

    Wang, Y. Z.; Zhang, C. L.; Dai, H.-H.; Chen, W. Q.

    2015-10-01

    This paper presents an asymptotic analysis of solitary waves propagating in an incompressible isotropic electroactive circular rod subjected to a biasing longitudinal electric displacement. Several asymptotic expansions are introduced to simplify the rod governing equations. The boundary conditions on the lateral surface of the rod are satisfied from the asymptotic point of view. In the limit of finite-small amplitude and long wavelength, a set of ten simplified one-dimensional nonlinear governing equations is established. To validate our approach and the derivation, we compare the linear dispersion relation with the one directly derived from the three-dimensional linear theory in the limit of long wavelength. Then, by the reductive perturbation method, we deduce the far-field equation (i.e. the KdV equation). Finally, the leading order of the electroelastic solitary wave solution is presented. Numerical examples are provided to show the influences of the biasing electric displacement and material constants on the solitary waves. It is found that the biasing electric displacement can modulate the velocity of solitary waves with a prescribed amplitude in the electroactive rod, a very interesting result which may promote the particular application of solitary waves in solids with multi-field coupling.

  18. Used Fuel Testing Transportation Model

    Energy Technology Data Exchange (ETDEWEB)

    Ross, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Best, Ralph E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Maheras, Steven J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jensen, Philip J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); England, Jeffery L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); LeDuc, Dan [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-09-25

    This report identifies shipping packages/casks that might be used by the Used Nuclear Fuel Disposition Campaign Program (UFDC) to ship fuel rods and pieces of fuel rods taken from high-burnup used nuclear fuel (UNF) assemblies to and between research facilities for purposes of evaluation and testing. Also identified are the actions that would need to be taken, if any, to obtain U.S. Nuclear Regulatory (NRC) or other regulatory authority approval to use each of the packages and/or shipping casks for this purpose.

  19. Used Fuel Testing Transportation Model

    Energy Technology Data Exchange (ETDEWEB)

    Ross, Steven B.; Best, Ralph E.; Maheras, Steven J.; Jensen, Philip J.; England, Jeffery L.; LeDuc, Dan

    2014-09-24

    This report identifies shipping packages/casks that might be used by the Used Nuclear Fuel Disposition Campaign Program (UFDC) to ship fuel rods and pieces of fuel rods taken from high-burnup used nuclear fuel (UNF) assemblies to and between research facilities for purposes of evaluation and testing. Also identified are the actions that would need to be taken, if any, to obtain U.S. Nuclear Regulatory (NRC) or other regulatory authority approval to use each of the packages and/or shipping casks for this purpose.

  20. Dimensional Measurements of Fresh CANDU Fuel Bundle

    Energy Technology Data Exchange (ETDEWEB)

    Jun, Ji Su; Jo, Chang Keun; Jung, Jong Yeob; Koo, Dae Seo; Cho, Moon Sung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    2005-07-01

    This paper intends to provide the dimensional measurements of fresh CANDU fuel (37-element) bundle for the estimation of deformation of post-irradiated (PI) bundle. It is expensive and difficult to measure the fretting wear of bearing pad, the element bowing and the waviness of endplate at the two-phase high flow condition (above 24 kg/s) of out-of-reactor test. So, it is recommended to compare the geometry of fresh bundle with that of PI bundle to estimate the integrity of fuel bundle in the CANDU-6 fuel channel with two-phase flow condition. The measurement system has been developed to provide the visual inspection and the dimensional measurements within the accuracy of 10 {mu}m. It is applicable in-air and underwater to the CANDU bundle as well as the CANFLEX bundle. The in-air measurements of the 36 fresh CANDU bundles (S/N: B400892 {approx} B400927) are done by this system from February 2004 to March 2004 in the PHWR fresh fuel storage building of KNFC. These bundles are produced by KNFC manufacturing procedure and are waiting for the delivery to the Wolsong-3 plant, and are planned to load into the proposed test channels. The detail measurements contain the outer rod profile (including the bearing pad), the diameter of bundle, the bowing of bundle, the rod length and the surface profile of end plate (waviness)

  1. Control of Rod-Rod Interactions in Poly(3-alkylthiophenes)

    Science.gov (United States)

    Ho, Victor; Boudouris, Bryan W.; Segalman, Rachel A.

    2010-03-01

    Poly(3-hexylthiophene) is a commonly used semiconducting polymer because of its relatively high charge transport ability, low band gap, and solution processiblity. Strong intermolecular interactions lead to the formation of nanofibers during crystallization, which prevents long-range microstructural ordering. We show rod-rod interactions, parameterized by the Maier-Saupe parameter, can be controlled by rational polythiophene side chain design. Effects of side chain passivation are evidenced by a depressed melting temperature and the presence of a liquid crystalline region. Additionally, the Maier-Saupe parameters are estimated for poly(3-dodecylthiophene) and poly(3-ethylhexylthiophene); the relative magnitudes of each are related to the interchain spacings obtained by x-ray diffraction experiments. The systematic tuning of the rod-rod interactions in polythiophenes allows for manipulation of the ratio of Maier-Saupe to the Flory-Huggins parameter, a crucial value in obtaining long-range order in rod-coil block copolymer morphologies.

  2. Coupling molecular catalysts with nanostructured surfaces for efficient solar fuel production

    Science.gov (United States)

    Jin, Tong

    Solar fuel generation via carbon dioxide (CO2) reduction is a promising approach to meet the increasing global demand for energy and to minimize the impact of energy consumption on climate change. However, CO2 is thermodynamically stable; its activation often requires the use of appropriate catalysts. In particular, molecular catalysts with well-defined structures and tunability have shown excellent activity in photochemical CO2 reduction. These homogenous catalysts, however, suffer from poor stability under photochemical conditions and difficulty in recycling from the reaction media. Heterogenized molecular catalysts, particularly those prepared by coupling molecular catalysts with solid-state surfaces, have attracted more attention in recent years as potential solutions to address the issues associated with molecular catalysts. In this work, solar CO2 reduction is investigated using systems coupling molecular catalysts with robust nanostructured surfaces. In Chapter 2, heterogenization of macrocyclic cobalt(III) and nickel (II) complexes on mesoporous silica surface was achieved by different methods. Direct ligand derivatization significantly lowered the catalytic activity of Co(III) complex, while grafting the Co(III) complex onto silica surface through Si-O-Co linkage resulted in hybrid catalysts with excellent activity in CO2 reduction in the presence of p-terphenyl as a molecular photosensitizer. An interesting loading effect was observed, in which the optimal activity was achieved at a medium Co(III) surface density. Heterogenization of the Ni(II) complex on silica surface has also been implemented, the poor photocatalytic activity of the hybrid catalyst can be attributed to the intrinsic nature of the homogeneous analogue. This study highlighted the importance of appropriate linking strategies in preparing functional heterogenized molecular catalysts. Coupling molecular complexes with light-harvesting surfaces could avoid the use of expensive molecular

  3. Cold model study of a fuel bed on a moving grate. Stage 1- Parameter study of the interaction between grate/pusher movements and fuel bed; Kallmodellstudie av en braenslebaedd paa roerlig rost. Etapp 1- Parameterstudie av samspelet mellan rost-/pusherroerelser och braenslebaedd

    Energy Technology Data Exchange (ETDEWEB)

    Broden, Henrik; Larfeldt, Jenny [TPS Termiska Processer AB, Nykoeping (Sweden)

    2004-03-01

    A cold model study on fuel bed transportation on a moving grate has been done. The objective of the project has been to study the interaction between pusher and grate movement, fuel properties, inclination of the grate and the stroke length of the grate rods affects bed feeding. The cold rig has twelve rows of rods, where every second row is movable and every second is fixed. The inclination of the grate can be invariably adjusted up to 20 deg and the maximum stroke of the rods is 10 cm. The experiments show that the feeding ratio between the pusher and the grate to a large extent controls the resulting fuel bed height at the grate. The trials also demonstrate that the grate inclination, stroke length of the grate rods and fuel properties affects the bed height. Reduced grate inclination increases the bed height, which demonstrates that the force of gravity is important for the bed feeding. Trails with reduced grate stroke length, at maintained feeding ratio, resulted in an increased bed height, which probably was caused by fuel particle arching in the vicinity of the moving rods. Fuel particle arching reduces the ability for the moving grate rods to transfer force to the fuel bed. In other aspects identical trials with dry wood chips and wet bark show that fuel properties also affects the bed height. Wet bark is more difficult for grate to feed, which results in an increased bed height. The experiments show that in principle bed transportation occur in parallel to the grate plane during grate feeding. Vertical mixing hardly exists. Detailed studies on fuel particle movement at different depth of the fuel bed show that particles at or near the surface are transported more quickly along the grate than particles deeper into the bed. The existence of a velocity gradient in the fuel bed is an important finding since it explains how dispersion of fuel particles can exist in spite of the absence of vertical mixing. The velocity gradient can also contribute to the

  4. Prediction of Forest Canopy and Surface Fuels from Lidar and Satellite Time Series Data in a Bark Beetle-Affected Forest

    Directory of Open Access Journals (Sweden)

    Benjamin C. Bright

    2017-08-01

    Full Text Available Wildfire behavior depends on the type, quantity, and condition of fuels, and the effect that bark beetle outbreaks have on fuels is a topic of current research and debate. Remote sensing can provide estimates of fuels across landscapes, although few studies have estimated surface fuels from remote sensing data. Here we predicted and mapped field-measured canopy and surface fuels from light detection and ranging (lidar and Landsat time series explanatory variables via random forest (RF modeling across a coniferous montane forest in Colorado, USA, which was affected by mountain pine beetles (Dendroctonus ponderosae Hopkins approximately six years prior. We examined relationships between mapped fuels and the severity of tree mortality with correlation tests. RF models explained 59%, 48%, 35%, and 70% of the variation in available canopy fuel, canopy bulk density, canopy base height, and canopy height, respectively (percent root-mean-square error (%RMSE = 12–54%. Surface fuels were predicted less accurately, with models explaining 24%, 28%, 32%, and 30% of the variation in litter and duff, 1 to 100-h, 1000-h, and total surface fuels, respectively (%RMSE = 37–98%. Fuel metrics were negatively correlated with the severity of tree mortality, except canopy base height, which increased with greater tree mortality. Our results showed how bark beetle-caused tree mortality significantly reduced canopy fuels in our study area. We demonstrated that lidar and Landsat time series data contain substantial information about canopy and surface fuels and can be used for large-scale efforts to monitor and map fuel loads for fire behavior modeling at a landscape scale.

  5. Prediction of forest canopy and surface fuels from Lidar and satellite time series data in a bark beetle-affected forest

    Science.gov (United States)

    Bright, Benjamin C.; Hudak, Andrew T.; Meddens, Arjan J.H.; Hawbaker, Todd J.; Briggs, Jenny S.; Kennedy, Robert E.

    2017-01-01

    Wildfire behavior depends on the type, quantity, and condition of fuels, and the effect that bark beetle outbreaks have on fuels is a topic of current research and debate. Remote sensing can provide estimates of fuels across landscapes, although few studies have estimated surface fuels from remote sensing data. Here we predicted and mapped field-measured canopy and surface fuels from light detection and ranging (lidar) and Landsat time series explanatory variables via random forest (RF) modeling across a coniferous montane forest in Colorado, USA, which was affected by mountain pine beetles (Dendroctonus ponderosae Hopkins) approximately six years prior. We examined relationships between mapped fuels and the severity of tree mortality with correlation tests. RF models explained 59%, 48%, 35%, and 70% of the variation in available canopy fuel, canopy bulk density, canopy base height, and canopy height, respectively (percent root-mean-square error (%RMSE) = 12–54%). Surface fuels were predicted less accurately, with models explaining 24%, 28%, 32%, and 30% of the variation in litter and duff, 1 to 100-h, 1000-h, and total surface fuels, respectively (%RMSE = 37–98%). Fuel metrics were negatively correlated with the severity of tree mortality, except canopy base height, which increased with greater tree mortality. Our results showed how bark beetle-caused tree mortality significantly reduced canopy fuels in our study area. We demonstrated that lidar and Landsat time series data contain substantial information about canopy and surface fuels and can be used for large-scale efforts to monitor and map fuel loads for fire behavior modeling at a landscape scale.

  6. LWR nuclear fuel bundle data for use in fuel bundle handling

    Energy Technology Data Exchange (ETDEWEB)

    Weihermiller, W.B.; Allison, G.S.

    1979-09-01

    Although increasing numbers of spent light water reactor (LWR) fuel bundles are moved into storage, no handling equipment is set up to manipulate all of the various types of fuel bundles. This report summarizes fuel bundle information of interest to the designer of such handling equipment. Dimensional descriptions are included with discussions of assembly procedure and manufacturer provisions for handling equipment. No attempt is made to make a complete compilation of dimensional information; the number of fuel bundle designs and design revisions makes it impractical. Because the fuel bundle designs are so varied, any equipment intended for handling all types of bundles will have to be designed with flexibility in mind. Besides the ability to manipulate fuel bundles in space, handling equipment may be required to locate an external surface or to position a cutting operation to avoid breaking a fuel rod pressure boundary. Even with the most sophisticated and flexible handling equipment, some situations will require use of the manufacturers' as-built descriptions of individual fuel bundles.

  7. Cuisenaire Rods Go to College.

    Science.gov (United States)

    Chinn, Phyllis; And Others

    1992-01-01

    Presents examples of questions and answers arising from a hands-on and exploratory approach to discrete mathematics using cuisenaire rods. Combinatorial questions about trains formed of cuisenaire rods provide the setting for discovering numerical patterns by experimentation and organizing the results using induction and successive differences.…

  8. Fabrication of free-standing PbSe micro-rods

    Science.gov (United States)

    Jain, S.; Mukherjee, S.; Guan, Z. P.; Ray, D.; Zhao, F.; Li, D.; Shi, Z.

    2007-07-01

    We have fabricated epitaxially grown PbSe micro-rods by the fold-back action of the thin film and have investigated the experimental factors affecting the size of the micro-rods. We observe that the initial layer thickness and the etching parameters of the sacrificial layer determined the final diameter of the rods. By individually mounting the rods on copper heat sink, we observe an approximately 100 times increase in photoluminescence (PL) intensity per surface area when compared to the bulk film before rolling into micro-rod. These results offer a promising future of microstructures to the technology of mid-infrared light-emitting devices.

  9. High-yield production of hydrophobins RodA and RodB from Aspergillus fumigatus in Pichia pastoris

    DEFF Research Database (Denmark)

    Pedersen, Mona Højgaard; Borodina, Irina; Moresco, Jacob Lange

    2011-01-01

    B on the surface of its conidia. RodA is known to be of importance to the pathogenesis of the fungus, while the biological role of RodB is currently unknown. Here, we report the successful expression of both hydrophobins in Pichia pastoris and present fed-batch fermentation yields of 200–300 mg/l fermentation...... broth. Protein bands of expected sizes were detected by SDS-PAGE and western blotting, and the identity was further confirmed by tandem mass spectrometry. Both proteins were purified using his-affinity chromatography, and the high level of purity was verified by silver-stained SDS-PAGE. Recombinant Rod...

  10. Role of Microstructure and Surface Defects on the Dissolution Kinetics of CeO2, a UO2 Fuel Analogue.

    Science.gov (United States)

    Corkhill, Claire L; Bailey, Daniel J; Tocino, Florent Y; Stennett, Martin C; Miller, James A; Provis, John L; Travis, Karl P; Hyatt, Neil C

    2016-04-27

    The release of radionuclides from spent fuel in a geological disposal facility is controlled by the surface mediated dissolution of UO2 in groundwater. In this study we investigate the influence of reactive surface sites on the dissolution of a synthesized CeO2 analogue for UO2 fuel. Dissolution was performed on the following: CeO2 annealed at high temperature, which eliminated intrinsic surface defects (point defects and dislocations); CeO2-x annealed in inert and reducing atmospheres to induce oxygen vacancy defects and on crushed CeO2 particles of different size fractions. BET surface area measurements were used as an indicator of reactive surface site concentration. Cerium stoichiometry, determined using X-ray Photoelectron Spectroscopy (XPS) and supported by X-ray Diffraction (XRD) analysis, was used to determine oxygen vacancy concentration. Upon dissolution in nitric acid medium at 90 °C, a quantifiable relationship was established between the concentration of high energy surface sites and CeO2 dissolution rate; the greater the proportion of intrinsic defects and oxygen vacancies, the higher the dissolution rate. Dissolution of oxygen vacancy-containing CeO2-x gave rise to rates that were an order of magnitude greater than for CeO2 with fewer oxygen vacancies. While enhanced solubility of Ce(3+) influenced the dissolution, it was shown that replacement of vacancy sites by oxygen significantly affected the dissolution mechanism due to changes in the lattice volume and strain upon dissolution and concurrent grain boundary decohesion. These results highlight the significant influence of defect sites and grain boundaries on the dissolution kinetics of UO2 fuel analogues and reduce uncertainty in the long term performance of spent fuel in geological disposal.

  11. Dynamic rod worth simulation study for a sodium-cooled TRU burner

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sang Ji; Ha, Pham Nhu Viet, E-mail: phamha@kaeri.re.kr; Lee, Min Jae; Kang, Chang Mu

    2015-12-15

    Highlights: • Dynamic rod worth calculation methodology for a sodium-cooled TRU burner was developed. • The spatial weighting functions were relatively insensitive to control rods position. • The simulated pseudo detector response agreed well with the calculated core power. • The simulated dynamic rod worths compared well against the simulated static values. • Impact of individual detector on the simulated dynamic worth was evaluated. - Abstract: This paper presents a preliminary dynamic rod worth simulation study for a TRU burner core mockup of the PGSFR (Korean Prototype Gen-IV Sodium-cooled Fast Reactor) named BFS-76-1A so as to establish a calculation methodology for evaluating the rod worth of the PGSFR. The simulation method was mainly based on a three-dimensional multi-group nodal diffusion transient code for fast reactors in which the rod drop simulation for the BFS-76-1A was performed and all the fuel assemblies were taken into account for the detector response calculation. Then the dynamic rod worths were inferred from the simulated detector responses using an inverse point kinetics model and compared against the simulated static worths. The results show good agreement between the simulated pseudo detector response and the calculated core power as well as between the simulated dynamic and static rod worths, and thus indicate that the dynamic rod worth simulation method developed in this work can be applied to the rod worth estimation and validation for the PGSFR.

  12. Engineering interface and surface of noble metal nanoparticle nanotubes toward enhanced catalytic activity for fuel cell applications.

    Science.gov (United States)

    Cui, Chun-Hua; Yu, Shu-Hong

    2013-07-16

    In order for fuel cells to have commercial viability as alternative fuel sources, researchers need to develop highly active and robust fuel cell electrocatalysts. In recent years, the focus has been on the design and synthesis of novel catalytic materials with controlled interface and surface structures. Another goal is to uncover potential catalytic activity and selectivity, as well as understand their fundamental catalytic mechanisms. Scientists have achieved great progress in the experimental and theoretical investigation due to the urgent demand for broad commercialization of fuel cells in automotive applications. However, there are still three main problems: cost, performance, and stability. To meet these targets, the catalyst needs to have multisynergic functions. In addition, the composition and structure changes of the catalysts during the reactions still need to be explored. Activity in catalytic nanomaterials is generally controlled by the size, shape, composition, and interface and surface engineering. As such, one-dimensional nanostructures such as nanowires and nanotubes are of special interest. However, these structures tend to lose the nanoparticle morphology and inhibit the use of catalysts in both fuel cell anodes and cathodes. In 2003, Rubinstein and co-workers proposed the idea of nanoparticle nanotubes (NNs), which combine the geometry of nanotubes and the morphology of nanoparticles. This concept gives both the high surface-to-volume ratio and the size effect, which are both appealing in electrocatalyst design. In this Account, we describe our developments in the construction of highly active NNs with unique surface and heterogeneous interface structures. We try to clarify enhanced activity and stability in catalytic systems by taking into account the activity impact factors. We briefly introduce material structural effects on the electrocatalytic reactivity including metal oxide/metal and metal/metal interfaces, dealloyed pure Pt, and mixed Pt

  13. Use of diesel engine and surface-piercing propeller to achieve fuel savings for inshore fishing boats

    Science.gov (United States)

    Zainol, Ismail; Yaakob, Omar

    2016-06-01

    Fishing is a major local industry in Malaysia, particularly in rural areas. However, the rapidly increasing price of fuel is seriously affecting the industry's viability. At present, outboard petrol engines are the preferred choice for use in small-scale fishing boats because they deliver the advantages of high speed and low weight, they are easy to install, and they use minimal space. Petrol outboard engines are known to consume a greater amount of fuel than inboard diesel engines, but installing diesel engines with conventional submerged propellers in existing small-scale fishing boats is not economically viable because major hullform modifications and extra expenditure are required to achieve this. This study describes a proposal to enable reductions in fuel consumption by introducing the combined use of a diesel engine and surface-piercing propeller (SPP). An analysis of fuel consumption reduction is presented, together with an economic feasibility study. Resulting data reveal that the use of the proposed modifications would save 23.31 liters of fuel per trip (40.75 %) compared to outboard motors, equaling annual savings of RM 3962 per year.

  14. Instant release of fission products in leaching experiments with high burn-up nuclear fuels in the framework of the Euratom project FIRST- Nuclides

    Science.gov (United States)

    Lemmens, K.; González-Robles, E.; Kienzler, B.; Curti, E.; Serrano-Purroy, D.; Sureda, R.; Martínez-Torrents, A.; Roth, O.; Slonszki, E.; Mennecart, T.; Günther-Leopold, I.; Hózer, Z.

    2017-02-01

    The instant release of fission products from high burn-up UO2 fuels and one MOX fuel was investigated by means of leach tests. The samples covered PWR and BWR fuels at average rod burn-up in the range of 45-63 GWd/tHM and included clad fuel segments, fuel segments with opened cladding, fuel fragments and fuel powder. The tests were performed with sodium chloride - bicarbonate solutions under oxidizing conditions and, for one test, in reducing Ar/H2 atmosphere. The iodine and cesium release could be partially explained by the differences in sample preparation, leading to different sizes and properties of the exposed surface areas. Iodine and cesium releases tend to correlate with FGR and linear power rating, but the scatter of the data is significant. Although the gap between the fuel and the cladding was closed in some high burn-up samples, fissures still provide possible preferential transport pathways.

  15. Measurements relating fire radiative energy density and surface fuel consumption - RxCADRE 2011 and 2012

    Science.gov (United States)

    Andrew T. Hudak; Matthew B. Dickinson; Benjamin C. Bright; Robert L. Kremens; E. Louise Loudermilk; Joseph J. O' Brien; Benjamin S. Hornsby; Roger D. Ottmar

    2016-01-01

    Small-scale experiments have demonstrated that fire radiative energy is linearly related to fuel combusted but such a relationship has not been shown at the landscape level of prescribed fires. This paper presents field and remotely sensed measures of pre-fire fuel loads, consumption, fire radiative energy density (FRED) and fire radiative power flux density (FRFD),...

  16. Oxidizing dissolution of spent MOX47 fuel subjected to water radiolysis: Solution chemistry and surface characterization by Raman spectroscopy

    Science.gov (United States)

    Jégou, C.; Caraballo, R.; De Bonfils, J.; Broudic, V.; Peuget, S.; Vercouter, T.; Roudil, D.

    2010-04-01

    The mechanisms of oxidizing dissolution of spent MOX fuel (MIMAS TU2®) subjected to water radiolysis were investigated experimentally by leaching spent MOX47 fuel samples in pure water at 25 °C under different oxidizing conditions (with and without external gamma irradiation); the leached surfaces were characterized by Raman spectroscopy. The highly oxidizing conditions resulting from external gamma irradiation significantly increased the concentration of plutonium (Pu(V)) and uranium (U(VI)) compared with a benchmark experiment (without external irradiation). The oxidation behavior of the plutonium-enriched aggregates differed significantly from that of the UO 2 matrix after several months of leaching in water under gamma irradiation. The plutonium in the aggregates appears to limit fuel oxidation. The only secondary phases formed and identified to date by Raman spectroscopy are uranium peroxides that generally precipitate on the surface of the UO 2 grains. Concerning the behavior of plutonium, solution analysis results appear to be compatible with a conventional explanation based on an equilibrium with a Pu(OH) 4(am) phase. The fission product release - considered as a general indicator of matrix alteration - from MOX47 fuel also increases under external gamma irradiation and a change in the leaching mode is observed. Diffusive leaching was clearly identified, coinciding with the rapid onset of steady-state actinide concentrations in the bulk solution.

  17. Incorporation of Integral Fuel Burnable Absorbers Boron and Gadolinium into Zirconium-Alloy Fuel Clad Material

    Energy Technology Data Exchange (ETDEWEB)

    Sridharan, K.; Renk, T.J.; Lahoda, E.J.; Corradini, M.L

    2004-12-14

    Long-lived fuels require the use of higher enrichments of 235U or other fissile materials. Such high levels of fissile material lead to excessive fuel activity at the beginning of life. To counteract this excessive activity, integral fuel burnable absorbers (IFBA) are added to some rods in the fuel assembly. The two commonly used IFBA elements are gadolinium, which is added as gadolinium-oxide to the UO2 powder, and boron, which is applied as a zirconium-diboride coating on the UO2 pellets using plasma spraying or chemical vapor deposition techniques. The incorporation of IFBA into the fuel has to be performed in a nuclear-regulated facility that is physically separated from the main plant. These operations tend to be very costly because of their small volume and can add from 20 to 30% to the manufacturing cost of the fuel. Other manufacturing issues that impact cost and performance are maintaining the correct levels of dosing, the reduction in fuel melting point due to gadolinium-oxide additions, and parasitic neutron absorption at fuel's end-of-life. The goal of the proposed research is to develop an alternative approach that involves incorporation of boron or gadolinium into the outer surface of the fuel cladding material rather than as an additive to the fuel pellets. This paradigm shift will allow for the introduction of the IFBA in a non-nuclear regulated environment and will obviate the necessity of additional handling and processing of the fuel pellets. This could represent significant cost savings and potentially lead to greater reproducibility and control of the burnable fuel in the early stages of the reactor operation. The surface alloying is being performed using the IBEST (Ion Beam Surface Treatment) process developed at Sandia National Laboratories. IBEST involves the delivery of energetic ion beam pulses onto the surface of a material, near-surface melting, and rapid solidification. The non-equilibrium nature of such processing allows for

  18. Retrieval analysis of PEEK rods for posterior fusion and motion preservation.

    Science.gov (United States)

    Kurtz, Steven M; Lanman, Todd H; Higgs, Genymphas; Macdonald, Daniel W; Berven, Sigurd H; Isaza, Jorge E; Phillips, Eual; Steinbeck, Marla J

    2013-12-01

    The purpose of this study was to analyze explanted PEEK rod spinal systems in the context of their clinical indications. We evaluated damage to the implant and histological changes in explanted periprosthetic tissues. 12 patients implanted with 23 PEEK rods were revised between 2008 and 2012. PEEK rods were of the same design (CD Horizon Legacy, Medtronic, Memphis TN, USA). Retrieved components were assessed for surface damage mechanisms, including plastic deformation, scratching, burnishing, and fracture. Patient history and indications for PEEK rod implantation were obtained from analysis of the medical records. 11/12 PEEK rod systems were employed for fusion at one level, and motion preservation at the adjacent level. Surgical complications in the PEEK cohort included a small dural tear in one case that was immediately repaired. There were no cases of PEEK rod fracture or pedicle screw fracture. Retrieved PEEK rods exhibited scratching, as well as impressions from the set screws and pedicle screw saddles. PEEK debris was observed in two patient tissues, which were located adjacent to PEEK rods with evidence of scratching and burnishing. This study documents the surface changes and tissue reactions for retrieved PEEK rod stabilization systems. Permanent indentations by the set screws and pedicle screws were the most prevalent observations on the surface of explanted PEEK rods.

  19. Magnetically labeled cells with surface-modified fe3 o4 spherical and rod-shaped magnetic nanoparticles for tissue engineering applications.

    Science.gov (United States)

    Gil, Sara; Correia, Clara R; Mano, João F

    2015-04-22

    Magnetically targeted cells with internalized magnetic nanoparticles (MNPs) could allow the success of cell transplantation and cell-based therapies, overcoming low cell retention that occurs when delivering cells by intravenous or local injection. Upon magnetization, these cells could then accumulate and stimulate the regeneration of the tissue in situ. Magnetic targeting of cells requires a detailed knowledge between interactions of engineered nanomaterials and cells, in particular the influence of shape and surface functionalization of MNPs. For the first time, cellular internalization of amino surface-modified iron oxide nanoparticles of two different shapes (nanospheres or nanorods) is studied. MNPs show high cellular uptake and labeled cells could exhibit a strong reaction with external magnetic fields. Compared to nanorods, nanospheres show better internalization efficiency, and labeled cells exhibit strong transportation reaction with external magnetic fields. Contiguous viable cell-sheets are developed by magnetic-force-based tissue engineering. The results confirm that the developed magnetic-responsive nano-biomaterials have potential applicability in tissue engineering or cellular therapies.

  20. Determination of plutonium content in TRR spent fuel by nondestructive neutron counting

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Y.-F. [Department of Engineering and System Science, National Tsing Hua University, 101, Sec. 2, Kung Fu Road, Hsinchu 30013, Taiwan (China); Sheu, R.-J. [National Synchrotron Radiation Research Center, 101 Hsin-Ann Road, Hsinchu Science Park, Hsinchu 30076, Taiwan (China); Chiao, L.-H.; Yuan, M.-C. [Institute of Nuclear Energy Research, 1000, Wenhua Road, Jiaan Village, Longtan Township, Taoyuan County 32546, Taiwan (China); Jiang, S.-H., E-mail: shjiang@mx.nthu.edu.t [Department of Engineering and System Science, National Tsing Hua University, 101, Sec. 2, Kung Fu Road, Hsinchu 30013, Taiwan (China); Institute of Nuclear Engineering and Science, National Tsing Hua University, 101, Sec. 2, Kung Fu Road, Hsinchu 30013, Taiwan (China)

    2010-07-21

    For the nuclear safeguard purpose, this work aims to nondestructively determine the plutonium content in the Taiwan Research Reactor (TRR) spent fuel rods in the storage pool before the stabilization process, which transforms the metal spent fuel rods into oxide powder. A SPent-fuel-Neutron-Counter (SPNC) system was designed and constructed to carry out underwater scan measurements of neutrons emitting from the spent fuel rod, from which the {sup 240}Pu mass in the fuel rod will be determined. The SAS2 H control module of the SCALE 5.1 code package was applied to calculate the {sup 240}Pu-to-Pu mass ratio in the TRR spent fuel rod according to the given power history. This paper presents the methodology and design of our detector system as well as the measurements of four TRR spent fuel rods in the storage pool and the comparison of the measured results with the facility declared values.

  1. Determination of plutonium content in TRR spent fuel by nondestructive neutron counting

    Science.gov (United States)

    Chen, Yen-Fu; Sheu, Rong-Jiun; Chiao, Ling-Huan; Yuan, Ming-Chen; Jiang, Shiang-Huei

    2010-07-01

    For the nuclear safeguard purpose, this work aims to nondestructively determine the plutonium content in the Taiwan Research Reactor (TRR) spent fuel rods in the storage pool before the stabilization process, which transforms the metal spent fuel rods into oxide powder. A SPent-fuel-Neutron-Counter (SPNC) system was designed and constructed to carry out underwater scan measurements of neutrons emitting from the spent fuel rod, from which the 240Pu mass in the fuel rod will be determined. The SAS2 H control module of the SCALE 5.1 code package was applied to calculate the 240Pu-to-Pu mass ratio in the TRR spent fuel rod according to the given power history. This paper presents the methodology and design of our detector system as well as the measurements of four TRR spent fuel rods in the storage pool and the comparison of the measured results with the facility declared values.

  2. Topological mixing with ghost rods

    Science.gov (United States)

    Gouillart, Emmanuelle; Thiffeault, Jean-Luc; Finn, Matthew D.

    2006-03-01

    Topological chaos relies on the periodic motion of obstacles in a two-dimensional flow in order to form nontrivial braids. This motion generates exponential stretching of material lines, and hence efficient mixing. Boyland, Aref, and Stremler [J. Fluid Mech. 403, 277 (2000)] have studied a specific periodic motion of rods that exhibits topological chaos in a viscous fluid. We show that it is possible to extend their work to cases where the motion of the stirring rods is topologically trivial by considering the dynamics of special periodic points that we call “ghost rods”, because they play a similar role to stirring rods. The ghost rods framework provides a new technique for quantifying chaos and gives insight into the mechanisms that produce chaos and mixing. Numerical simulations for Stokes flow support our results.

  3. Simulation of alpha dose for predicting radiolytic species at the surface of spent nuclear fuel pellets

    OpenAIRE

    Becker Frank; Kienzler Bernhard

    2014-01-01

    In many countries, spent nuclear fuel is considered as a waste form to be disposed of in underground disposal. Under deep host rock conditions, a reducing environment prevails. In the case of water contact, long-term radionuclide release from the fuel depends on dissolution processes of the UO2 matrix. The dissolution rate of irradiated UO2 is controlled by oxidizing processes facilitated by dissolved species formed by alpharadiolysis of water in contact with spent nuc...

  4. Catalytic Surface Promotion of Composite Cathodes in Protonic Ceramic Fuel Cells

    DEFF Research Database (Denmark)

    Solis, Cecilia; Navarrete, Laura; Bozza, Francesco;

    2015-01-01

    Composite cathodes based on an electronic conductor and a protonic conductor show advantages for protonic ceramic fuel cells. In this work, the performance of a La5.5WO11.25-δ/ La0.8Sr0.2MnO3+δ (LWO/LSM) composite cathode in a fuel cell based on an LWO protonic conducting electrolyte is shown and...

  5. Energy efficient one-pot synthesis of durable superhydrophobic coating through nylon micro-rods

    Science.gov (United States)

    Simovich, T.; Wu, A. H.; Lamb, R. N.

    2014-03-01

    A durable and superhydrophobic coating was fabricated at room temperature through encapsulating nylon micro-rods in a hydrophobic silica shell. This was achieved through the precipitation of miniemulsified nylon under high shear to generate micro-rods with high aspect ratio in the presence of methyltrimethoxysilane. The resultant coating structure resembles a network of highly entangled micro-rods that give rise to both surface roughness and hydrophobicity, resulting in contact angles greater than 155°. The embedded nylon polymer within the micro-rods imparts significant mechanical durability to the surface, resulting in a coating hardness of 2H using the pencil hardness test.

  6. Synergistic Smart Fuel For Microstructure Mediated Measurements

    Energy Technology Data Exchange (ETDEWEB)

    James A. Smith; Dale K. Kotter; Steven L. Garrett; Randall A. Ali

    2013-07-01

    Advancing the Nuclear Fuel Cycle and Next Generation Nuclear Power Plants requires enhancing our basic understanding of fuel and materials behavior under irradiation. The two most significant issues limiting the effectiveness and lifespan of the fuel are the loss of thermal conductivity of the fuel and the mechanical strength of both fuel and cladding. The core of a nuclear reactor presents an extremely harsh and challenging environment for both sensors and telemetry due to elevated temperatures and large fluxes of energetic and ionizing particles from radioactive decay processes. The majority of measurements are made in reactors using “radiation hardened” sensors and materials. A different approach has been pursued in this research that exploits high temperatures and materials that are robust with respect to ionizing radiation. This synergistically designed thermoacoustic sensor will be self-powered, wireless, and provide telemetry. The novel sensor will be able to provide reactor process information even if external electrical power and communication are unavailable. In addition, the form-factor for the sensor is identical to the existing fuel rods within reactors and contains no moving parts. Results from initial proof of concept experiments designed to characterize porosity, surface properties and monitor gas composition will be discussed.

  7. Synergistic smart fuel for microstructure mediated measurements

    Science.gov (United States)

    Smith, James A.; Kotter, Dale K.; Ali, Randall A.; Garrett, Steven L.

    2014-02-01

    Advancing the Nuclear Fuel Cycle and Next Generation Nuclear Power Plants requires enhancing our basic understanding of fuel and materials behavior under irradiation. The two most significant issues limiting the effectiveness and lifespan of the fuel are the loss of thermal conductivity of the fuel and the mechanical strength of both fuel and cladding. The core of a nuclear reactor presents an extremely harsh and challenging environment for both sensors and telemetry due to elevated temperatures and large fluxes of energetic and ionizing particles from radioactive decay processes. The majority of measurements are made in reactors using "radiation hardened" sensors and materials. A different approach has been pursued in this research that exploits high temperatures and materials that are robust with respect to ionizing radiation. This synergistically designed thermoacoustic sensor will be self-powered, wireless, and provide telemetry. The novel sensor will be able to provide reactor process information even if external electrical power and communication are unavailable. In addition, the form-factor for the sensor is identical to the existing fuel rods within reactors and contains no moving parts. Results from initial proof of concept experiments designed to characterize porosity, surface properties and monitor gas composition will be discussed.

  8. Synergistic smart fuel for microstructure mediated measurements

    Energy Technology Data Exchange (ETDEWEB)

    Smith, James A.; Kotter, Dale K. [Idaho National Laboratory, Fuel Performance and Design, P.O. Box 1625, Idaho Falls, Idaho, 83415-6188 (United States); Ali, Randall A. [Graduate Program in Acoustics and Applied Research Laboratory, Penn State University, P. . Box 30, M/S 3520D, State College, PA 16804-0030 (United States); Garrett, Steven L. [Graduate Program in Acoustics and Applied Research Laboratory, Penn State University, P.O. Box 30, M/S 3520D, State College, PA 16804-0030 (United States)

    2014-02-18

    Advancing the Nuclear Fuel Cycle and Next Generation Nuclear Power Plants requires enhancing our basic understanding of fuel and materials behavior under irradiation. The two most significant issues limiting the effectiveness and lifespan of the fuel are the loss of thermal conductivity of the fuel and the mechanical strength of both fuel and cladding. The core of a nuclear reactor presents an extremely harsh and challenging environment for both sensors and telemetry due to elevated temperatures and large fluxes of energetic and ionizing particles from radioactive decay processes. The majority of measurements are made in reactors using 'radiation hardened' sensors and materials. A different approach has been pursued in this research that exploits high temperatures and materials that are robust with respect to ionizing radiation. This synergistically designed thermoacoustic sensor will be self-powered, wireless, and provide telemetry. The novel sensor will be able to provide reactor process information even if external electrical power and communication are unavailable. In addition, the form-factor for the sensor is identical to the existing fuel rods within reactors and contains no moving parts. Results from initial proof of concept experiments designed to characterize porosity, surface properties and monitor gas composition will be discussed.

  9. CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 8 AND 9 CRYSTAL RIVER UNIT 3

    Energy Technology Data Exchange (ETDEWEB)

    Michael L. Wilson

    2001-02-08

    The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 8 and 9 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

  10. CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

    Energy Technology Data Exchange (ETDEWEB)

    Kenneth D. Wright

    1997-07-30

    The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

  11. Fuel assembly reconstitution

    Energy Technology Data Exchange (ETDEWEB)

    Morgado, Mario M.; Oliveira, Monica G.N.; Ferreira Junior, Decio B.M.; Santos, Barbara O. dos; Santos, Jorge E. dos, E-mail: mongeor@eletronuclear.gov.b [ELETROBRAS Termonuclear S.A. - ELETRONUCLEAR, Angra dos Reis, RJ (Brazil)

    2009-07-01

    Fuel failures have been happened in Nuclear Power Plants worldwide, without lost of integrity and safety, mainly for the public, environment and power plants workers. The most common causes of these events are corrosion (CRUD), fretting and pellet cladding interaction. These failures are identified by increasing the activity of fission products, verified by chemical analyses of reactor coolant. Through these analyses, during the fourth operation cycle of Angra 2 Nuclear Power Plant, was possible to observe fuel failure indication. This indication was confirmed in the end of the cycle during the unloading of reactor core through leakage tests of fuel assembly, using the equipment called 'In Mast Sipping' and 'Box Sipping'. After confirmed, the fuel assembly reconstitution was scheduled, and happened in April, 2007, where was identified the cause and the fuel rod failure, which was substitute by dummy rods (zircaloy). The cause was fretting by 'debris'. The actions to avoid and prevent fuel assemblies failures are important. The goals of this work are to describe the methodology of fuel assembly reconstitution using the FARE (Fuel Assembly Reconstitution Equipment) system, to describe the results of this task in economic and security factors of the company and show how the fuel assembly failures are identified during operation and during the outage. (author)

  12. Surface composition effect of nitriding Ni-free stainless steel as bipolar plate of polymer electrolyte fuel cell

    Science.gov (United States)

    Yu, Yang; Shironita, Sayoko; Nakatsuyama, Kunio; Souma, Kenichi; Umeda, Minoru

    2016-12-01

    In order to increase the corrosion resistance of low cost Ni-free SUS445 stainless steel as the bipolar plate of a polymer electrolyte fuel cell, a nitriding surface treatment experiment was carried out in a nitrogen atmosphere under vacuum conditions, while an Ar atmosphere was used for comparison. The electrochemical performance, microstructure, surface chemical composition and morphology of the sample before and after the electrochemical measurements were investigated using linear sweep voltammetry (LSV), X-ray diffraction (XRD), glow discharge optical emission spectroscopy (GDS) and laser scanning microscopy (LSM) measurements. The results confirmed that the nitriding heat treatment not only increased the corrosion resistance, but also improved the surface conductivity of the Ni-free SUS445 stainless steel. In contrast, the corrosion resistance of the SUS445 stainless steel decreased after heat treatment in an Ar atmosphere. These results could be explained by the different surface compositions between these samples.

  13. MASS TRANSFER LIMITATION IN DIFFERENT ANODE ELECTRODE SURFACE AREAS ON THE PERFORMANCE OF DUAL CHAMBER MICROBIAL FUEL CELL

    Directory of Open Access Journals (Sweden)

    Majid Sadeqzadeh

    2012-01-01

    Full Text Available In this study, the effect of different electrode surface areas on the performance of dual chamber Microbial Fuel Cells (MFC was investigated. Four different electrodes with 12, 16, 20 and 24 cm2 surface areas were tested in an MFC system. The 20 cm2 electrode generated an output power of 76.5 mW/m2 was found to be the highest among all the electrodes tested. This might be due to better interactions with microorganism and less mass transfer limitation. In addition, this indicates that the chances for attachment of bacteria and generation of electricity in larger electrode surface areas might be limited by mass transport and by higher surface area. The output power generation was then followed by the 16, 12 and 24 cm2 electrodes which generated 69.6, 64.7 and 61.25 mW/m2 electricity, respectively.

  14. Proton exchange membrane fuel cell model for aging predictions: Simulated equivalent active surface area loss and comparisons with durability tests

    Science.gov (United States)

    Robin, C.; Gérard, M.; Quinaud, M.; d'Arbigny, J.; Bultel, Y.

    2016-09-01

    The prediction of Proton Exchange Membrane Fuel Cell (PEMFC) lifetime is one of the major challenges to optimize both material properties and dynamic control of the fuel cell system. In this study, by a multiscale modeling approach, a mechanistic catalyst dissolution model is coupled to a dynamic PEMFC cell model to predict the performance loss of the PEMFC. Results are compared to two 2000-h experimental aging tests. More precisely, an original approach is introduced to estimate the loss of an equivalent active surface area during an aging test. Indeed, when the computed Electrochemical Catalyst Surface Area profile is fitted on the experimental measures from Cyclic Voltammetry, the computed performance loss of the PEMFC is underestimated. To be able to predict the performance loss measured by polarization curves during the aging test, an equivalent active surface area is obtained by a model inversion. This methodology enables to successfully find back the experimental cell voltage decay during time. The model parameters are fitted from the polarization curves so that they include the global degradation. Moreover, the model captures the aging heterogeneities along the surface of the cell observed experimentally. Finally, a second 2000-h durability test in dynamic operating conditions validates the approach.

  15. Surface Area Expansion of Electrodes with Grass-like Nanostructures to Enhance Electricity Generation in Microbial Fuel Cells

    DEFF Research Database (Denmark)

    Al Atraktchi, Fatima Al-Zahraa; Zhang, Yifeng; Noori, Jafar Safaa;

    2012-01-01

    Microbial fuel cells (MFCs) have applications possibilities for wastewater treatment, biotransformation, and biosensor, but the development of highly efficient electrode materials is critical for enhancing the power generation. Two types of electrodes modified with nanoparticles or grass-like nan......Microbial fuel cells (MFCs) have applications possibilities for wastewater treatment, biotransformation, and biosensor, but the development of highly efficient electrode materials is critical for enhancing the power generation. Two types of electrodes modified with nanoparticles or grass...... of plain silicium showed a maximum power density of 86.0 mW/m2. Further expanding the surface area of carbon paper electrodes with gold nanoparticles resulted in a maximum stable power density of 346.9 mW/m2 which is 2.9 times higher than that achieved with conventional carbon paper. These results show...... that fabrication of electrodes with nanograss could be an efficient way to increase the power generation....

  16. Prediction of CRUD deposition on PWR fuel using a state-of-the-art CFD-based multi-physics computational tool

    Energy Technology Data Exchange (ETDEWEB)

    Petrov, Victor [Department of Nuclear Engineering & Radiological Sciences, University of Michigan, 2355 Bonisteel Boulv, Ann Arbor, MI (United States); Kendrick, Brian K. [Theoretical Division (T-1, MS B221), Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Walter, Daniel [Department of Nuclear Engineering & Radiological Sciences, University of Michigan, 2355 Bonisteel Boulv, Ann Arbor, MI (United States); Manera, Annalisa, E-mail: manera@umich.edu [Department of Nuclear Engineering & Radiological Sciences, University of Michigan, 2355 Bonisteel Boulv, Ann Arbor, MI (United States); Secker, Jeffrey [Westinghouse Electric Company Nuclear Fuel Division, 1000 Westinghouse Drive, Cranberry Township, PA 16066 (United States)

    2016-04-01

    In the present paper we report about the first attempt to demonstrate and assess the ability of state-of-the-art high-fidelity computational tools to reproduce the complex patterns of CRUD deposits found on the surface of operating Pressurized Water Reactors (PWRs) fuel rods. A fuel assembly of the Seabrook Unit 1 PWR was selected as the test problem. During Seabrook Cycle 5, CRUD induced power shift (CIPS) and CRUD induced localized corrosion (CILC) failures were observed. Measurements of the clad oxide thi