Heat transfer on HLM cooled wire-spaced fuel pin bundle simulator in the NACIE-UP facility

Energy Technology Data Exchange (ETDEWEB)

Di Piazza, Ivan, E-mail: ivan.dipiazza@enea.it [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone, Camugnano (Italy); Angelucci, Morena; Marinari, Ranieri [University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Pisa (Italy); Tarantino, Mariano [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone, Camugnano (Italy); Forgione, Nicola [University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Pisa (Italy)

2016-04-15

Highlights: • Experiments with a wire-wrapped 19-pin fuel bundle cooled by LBE. • Wall and bulk temperature measurements at three axial positions. • Heat transfer and error analysis in the range of low mass flow rates and Péclet number. • Comparison of local and section-averaged Nusselt number with correlations. - Abstract: The NACIE-UP experimental facility at the ENEA Brasimone Research Centre (Italy) allowed to evaluate the heat transfer coefficient of a wire-spaced fuel bundle cooled by lead-bismuth eutectic (LBE). Lead or lead-bismuth eutectic are very attractive as coolants for the GEN-IV fast reactors due to the good thermo-physical properties and the capability to fulfil the GEN-IV goals. Nevertheless, few experimental data on heat transfer with heavy liquid metals (HLM) are available in literature. Furthermore, just a few data can be identified on the specific topic of wire-spaced fuel bundle cooled by HLM. Additional analysis on thermo-fluid dynamic behaviour of the HLM inside the subchannels of a rod bundle is necessary to support the design and safety assessment of GEN. IV/ADS reactors. In this context, a wire-spaced 19-pin fuel bundle was installed inside the NACIE-UP facility. The pin bundle is equipped with 67 thermocouples to monitor temperatures and analyse the heat transfer behaviour in different sub-channels and axial positions. The experimental campaign was part of the SEARCH FP7 EU project to support the development of the MYRRHA irradiation facility (SCK-CEN). Natural and mixed circulation flow regimes were investigated, with subchannel Reynolds number in the range Re = 1000–10,000 and heat flux in the range q″ = 50–500 kW/m{sup 2}. Local Nusselt numbers were calculated for five sub-channels in different ranks at three axial positions. Section-averaged Nusselt number was also defined and calculated. Local Nusselt data showed good consistency with some of the correlation existing in literature for heat transfer in liquid metals

Heat transfer on HLM cooled wire-spaced fuel pin bundle simulator in the NACIE-UP facility

International Nuclear Information System (INIS)

Di Piazza, Ivan; Angelucci, Morena; Marinari, Ranieri; Tarantino, Mariano; Forgione, Nicola

2016-01-01

Highlights: • Experiments with a wire-wrapped 19-pin fuel bundle cooled by LBE. • Wall and bulk temperature measurements at three axial positions. • Heat transfer and error analysis in the range of low mass flow rates and Péclet number. • Comparison of local and section-averaged Nusselt number with correlations. - Abstract: The NACIE-UP experimental facility at the ENEA Brasimone Research Centre (Italy) allowed to evaluate the heat transfer coefficient of a wire-spaced fuel bundle cooled by lead-bismuth eutectic (LBE). Lead or lead-bismuth eutectic are very attractive as coolants for the GEN-IV fast reactors due to the good thermo-physical properties and the capability to fulfil the GEN-IV goals. Nevertheless, few experimental data on heat transfer with heavy liquid metals (HLM) are available in literature. Furthermore, just a few data can be identified on the specific topic of wire-spaced fuel bundle cooled by HLM. Additional analysis on thermo-fluid dynamic behaviour of the HLM inside the subchannels of a rod bundle is necessary to support the design and safety assessment of GEN. IV/ADS reactors. In this context, a wire-spaced 19-pin fuel bundle was installed inside the NACIE-UP facility. The pin bundle is equipped with 67 thermocouples to monitor temperatures and analyse the heat transfer behaviour in different sub-channels and axial positions. The experimental campaign was part of the SEARCH FP7 EU project to support the development of the MYRRHA irradiation facility (SCK-CEN). Natural and mixed circulation flow regimes were investigated, with subchannel Reynolds number in the range Re = 1000–10,000 and heat flux in the range q″ = 50–500 kW/m"2. Local Nusselt numbers were calculated for five sub-channels in different ranks at three axial positions. Section-averaged Nusselt number was also defined and calculated. Local Nusselt data showed good consistency with some of the correlation existing in literature for heat transfer in liquid metals for

Investigations of flow and temperature field development in bare and wire-wrapped reactor fuel pin bundles cooled by sodium

International Nuclear Information System (INIS)

Govindha Rasu, N.; Velusamy, K.; Sundararajan, T.; Chellapandi, P.

2013-01-01

Highlights: ► We study sodium flow and temperature development in fuel pin bundles. ► Pin diameter, number of pins, wire wrap and ligament gap are varied as parameters. ► Flow development is achieved within ∼30–40 hydraulic diameters. ► Thermal development is attained only for small pin diameter and less number of pins. ► Wire wrap and ligament gap strongly influence Nusselt number. - Abstract: Simultaneous development of liquid sodium flow and temperature fields in the heat generating pin bundles of reactor has been investigated. Development characteristics are seen to be strongly influenced by pin diameter, number of pins, helical wire-wrap, ligament gap between the last row of pins and hexcan wall and Reynolds number. Flow development is achieved within an axial length of ∼125 hydraulic diameters, for all the pin bundle configurations considered. But temperature development is attained only if the pin diameter is small or the number of pins is less. In the case of large pin diameter with more pins, temperature development could not be achieved even after a length of ∼1000 hydraulic diameters. The reason for this behavior is traced to be the weak communication among sub-channels in tightly packed bundles. It is seen that the pin Nusselt number decreases from center to periphery in a bundle. Also, if the ligament gap is narrow, the Nusselt number is large and more uniform. Flow development length is short if the Reynolds number is large and the converse is true for thermal development length. Helical wire-wrap shortens the thermal entry length and significantly enhances the global Nusselt number. But, its influence on hydrodynamic entry length is not significant

Measurement of fission gas release, internal pressure and cladding creep rate in the fuel pins of PHWR bundle of normal discharge burnup

Energy Technology Data Exchange (ETDEWEB)

Viswanathan, U.K. [Post Irradiation Examination Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Sah, D.N., E-mail: dnsah@barc.gov.i [Post Irradiation Examination Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Rath, B.N.; Anantharaman, S. [Post Irradiation Examination Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

2009-08-01

Fuel pins of a Pressurised Heavy Water Reactor (PHWR) fuel bundle discharged from Narora Atomic Power Station unit no. 1 after attaining a fuel burnup of 7528 MWd/tU have been subjected to two types of studies, namely (i) puncture test to estimate extent of fission gas release and internal pressure in the fuel pin and (ii) localized heating of the irradiated fuel pin to measure the creep rate of the cladding in temperature range 800 deg. C - 900 deg. C. The fission gas release in the fuel pins from the outer ring of the bundle was found to be about 8%. However, only marginal release was found in fuel pins from the middle ring and the central fuel pin. The internal gas pressure in the outer fuel pin was measured to be 0.55 +- 0.05 MPa at room temperature. In-cell isothermal heating of a small portion of the outer fuel pins was carried out at 800 deg. C, 850 deg. C and 900 deg. C for 10 min and the increase in diameter of the fuel pin was measured after heat treatment. Creep rates of the cladding obtained from the measurement of the diameter change of the cladding due to heating at 800 deg. C, 850 deg. C and 900 deg. C were found respectively to be 2.4 x 10{sup -5} s{sup -1}, 24.6 x 10{sup -5} s{sup -1} and 45.6 x 10{sup -5} s{sup -1}.

Study on velocity field in a wire wrapped fuel pin bundle of sodium cooled reactor. Detailed velocity distribution in a subchannel

International Nuclear Information System (INIS)

Sato, Hiroyuki; Kobayashi, Jun; Miyakoshi, Hiroyuki; Kamide, Hideki

2009-01-01

A sodium cooled fast reactor is designed to attain a high burn-up core in a feasibility study on commercialized fast reactor cycle systems. In high burn-up fuel subassemblies, deformation of fuel pin due to the swelling and thermal bowing may decrease local flow velocity via change of flow area in the subassembly and influence the heat removal capability. Therefore, it is of importance to obtain the flow velocity distribution in a wire wrapped pin bundle. A 2.5 times enlarged 7-pin bundle water model was applied to investigate the detailed velocity distribution in an inner subchannel surrounded by 3 pins with wrapping wire. The test section consisted of a hexagonal acrylic duct tube and fluorinated resin pins which had nearly the same refractive index with that of water and a high light transmission rate. The velocity distribution in an inner subchannel with the wrapping wire was measured by PIV (Particle Image Velocimetry) through the front and lateral sides of the duct tube. In the vertical velocity distribution in a narrow space between the pins, the wrapping wire decreased the velocity downstream of the wire and asymmetric flow distribution was formed between the pin and wire. In the horizontal velocity distribution, swirl flow around the wrapping wire was obviously observed. The measured velocity data are useful for code validation of pin bundle thermalhydraulics. (author)

Positioning and locking device for fuel pin to grid attachment

International Nuclear Information System (INIS)

Frick, T.M.; Wineman, A.L.

1976-01-01

A positioning and locking device for fuel pin to grid attachment provides an inexpensive means of positively positioning and locking the individual fuel pins which make up the driver fuel assemblies used in nuclear reactors. The device can be adapted for use with a currently used attachment grid assembly design and insures that the pins remain in their proper position throughout the in-reactor life of the assembly. This device also simplifies fuel bundle assembly in that a complete row of fuel pins can be added to the bundle during each step of assembly. 8 claims, 8 drawing figures

Preliminary Analysis of the Bundle-Duct Interaction for the fuel of SFR

Energy Technology Data Exchange (ETDEWEB)

Lee, Byoung Oon; Cheon, Jin Sik; Hahn, Do Hee; Lee, Chan Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-10-15

BDI (Bundle-Duct Interaction) occurs in the fuel of SFR (Sodium-cooled Fast Reactor) due to the radial expansion and bowing of a fuel pin bundle. Under the BDI condition, excess cladding strain and hot spots would occur. Therefore, BDI, which is the dominant deformation mechanisms in a fuel pin bundle, should be considered to evaluate the FBR fuel integrity. The analysis codes such as ETOILE and BMBOO, have been developed to evaluate the BDI behavior. The bundle duct interaction model is also being developed for SFR in Korea. This model is based on ANSYS. In this paper, the fuel pin configuration model for the BDI calculation was established. The preliminary analysis of the bundle-duct interaction was performed to evaluate the fuel design concept.

Post-irradiation examination of a failed PHWR fuel bundle of KAPS-2

International Nuclear Information System (INIS)

Mishra, Prerna; Unnikrishnan, K.; Viswanathan, U.K.; Shriwastaw, R.S.; Singh, J.L.; Ouseph, P.M.; Alur, V.D.; Singh, H.N.; Anantharaman, S.; Sah, D.N.

2006-08-01

Detailed post irradiation examination was carried out on a PHWR fuel bundle irradiated at Kakrapar Atomic Power Station unit 2 (KAPS-2). The fuel bundle had failed early in life at a low burnup of 387 MWd/T. Non destructive and destructive examination was carried out to identify the cause of fuel failure. Visual examination and leak testing indicated failure in two fuel pins of the outer ring of the bundle in the form of axial cracks near the end plug location. Ultrasonic testing of the end cap weld indicated presence of lack of fusion type defect in the two fuel pins. No defect was found in other fuel pins of the bundle. Metallographic examination of fuel sections taken from the crack location in the failed fuel pin showed extensive restructuring of fuel. The centre temperature of the fuel had exceeded 1700 degC at this location in the failed fuel pin, whereas fuel centre temperature in the un-failed fuel pin was only about 1300 degC. Severe fuel clad interaction was observed in the failed fuel pin at and near the location of failure but no such interaction was observed in the un-failed fuel pins. Several incipient cracks originating from the inside surface were found in the cladding near failure location in addition to the main through wall crack. The incipient cracks were filled with interaction products and hydride platelets were present at tip of the cracks. It was concluded from the observations that the primary cause of failure was the presence of a part-wall defect in the end cap weld of the fuel pins. These defects opened up during reactor operation leading to steam ingress into the fuel, which caused high fuel centre temperature and severe fuel-cladding interaction resulting in secondary failures. A more stringent inspection and quality control of end plug weld during fabrication using ultrasonic test has been recommended to avoid such failure. (author)

Computer code TOBUNRAD for PWR fuel bundle heat-up calculations

International Nuclear Information System (INIS)

Shimooke, Takanori; Yoshida, Kazuo

1979-05-01

The computer code TOBUNRAD developed is for analysis of ''fuel-bundle'' heat-up phenomena in a loss-of-coolant accident of PWR. The fuel bundle consists of fuel pins in square lattice; its behavior is different from that of individual pins during heat-up. The code is based on the existing TOODEE2 code which analyzes heat-up phenomena of single fuel pins, so that the basic models of heat conduction and transfer and coolant flow are the same as the TOODEE2's. In addition to the TOODEE2 features, unheated rods are modeled and radiation heat loss is considered between fuel pins, a fuel pin and other heat sinks. The TOBUNRAD code is developed by a new FORTRAN technique which makes it possible to interrupt a flow of program controls wherever desired, thereby attaching several subprograms to the main code. Users' manual for TOBUNRAD is presented: The basic program-structure by interruption method, physical and computational model in each sub-code, usage of the code and sample problems. (author)

Development of a FBR fuel bundle-duct interaction analysis code-BAMBOO. Analysis model and verification by Phenix high burn-up fuel subassemblies

International Nuclear Information System (INIS)

Uwaba, Tomoyuki; Ito, Masahiro; Ukai, Shigeharu

2005-01-01

The bundle-duct interaction analysis code ''BAMBOO'' has been developed for the purpose of predicting deformation of a wire-wrapped fuel pin bundle of a fast breeder reactor (FBR). The BAMBOO code calculates helical bowing and oval-distortion of all the fuel pins in a fuel subassembly. We developed deformation models in order to precisely analyze the irradiation induced deformation by the code: a model to analyze fuel pin self-bowing induced by circumferential gradient of void swelling as well as thermal expansion, and a model to analyze dispersion of the orderly arrangement of a fuel pin bundle. We made deformation analyses of high burn-up fuel subassemblies in Phenix reactor and compared the calculated results with the post irradiation examination data of these subassemblies for the verification of these models. From the comparison we confirmed that the calculated values of the oval-distortion and bowing reasonably agreed with the PIE results if these models were used in the analysis of the code. (author)

COBRA-3M: a digital computer code for analyzing thermal-hydraulic behavior in pin bundles

International Nuclear Information System (INIS)

Marr, W.W.

1975-03-01

The COBRA-3M computer program is a modification of the thermal-hydraulic subchannel-analysis program COBRA-III. It includes detailed thermal models of fuel pin and duct wall. It is especially suitable for analyzing small pin bundles used in in-reactor or out-of-reactor experiments. (U.S.)

Probabilistic distributions of pin gaps within a wire-spaced fuel subassembly and sensitivities of the related uncertainties to pin gap

International Nuclear Information System (INIS)

Sakai, K.; Hishida, H.

1978-01-01

Probabilistic fuel pin gap distributions within a wire-spaced fuel subassembly and sensitivities of the related uncertainties to fuel pin gaps are discussed. The analyses consist mainly of expressing a local fuel pin gap in terms of sensitivity functions of the related uncertainties and calculating the corresponding probabilistic distribution through taking all the possible combinations of the distribution of uncertainties. The results of illustrative calculations show that with the reliability level of 0.9987, the maximum deviation of the pin gap at the cladding hot spot of a center fuel subassembly is 8.05% from its nominal value and the corresponding probabilistic pin gap distribution is shifted to the narrower side due to the external confinement of a pin bundle with a wrapper tube. (Auth.)

Evaluation of bundle duct interaction by out of pile compressive test of FBR bundles. FFTF type bundle

Energy Technology Data Exchange (ETDEWEB)

Tanaka, Kosuke; Yamamoto, Yuji; Nagamine, Tsuyoshi; Maeda, Koji [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center

2000-10-01

Bundle duct interaction (BDI) caused by expansion of fuel pin bundle becomes one of the main limiting factors for fuel life times. Then, it is important for the design of fast reactor fuel assembly to understand the BDI behavior in detail. In order to understand the BDI behavior, out of pile compressive tests were conducted for FFTF type bundle by use of X-ray CT equipment. In these compressive tests, two type bundles with different accuracy of initial wire position were conducted. The objective of this test is to evaluate the influence of the initial error from standard position of wire at the same axial position. The locations of the pins and the duct flats are analyzed from CT image data. Quantitative evaluation was performed at the CT image data and discussed the bundle deformation status under BDI condition. Following results are obtained. 1) The accuracy of initial wire position is strongly depends on the pin-to-duct contact behavior. In the case of bundle with large error from standard position, pin-to-duct contact is delayed. 2) The BDI mitigation of the bundle with small error from standard wire position is following: The elastic ovality is the dominant deformation in mild BDI condition, then the wire dispersion and pin dispersion are occurred in severe BDI condition. 3) The BDI mitigation of the bundle with large error from standard wire position is following: The elastic ovality and local bowing of pins with large error from standard wire position are occurred in mild BDI condition, then pin dispersion is occurred around pins with large error from standard wire position, finally wire dispersion is occurred in severe BDI condition. 4) The existence of pins with large error from standard wire position is effective to delay the pin-to-duct contact, but the existence of these pins is possible to contact of pin- to- pin. (author)

Fluid-mixing studies in a hexagonal 217-pin wire-wrapped rod bundle

International Nuclear Information System (INIS)

Symolon, P.D.; Todreas, N.E.

1981-02-01

Mixing, pressure drop, and flow split experiments were performed on a 217 pin LMFBR fuel bundle with a pitch to diameter ratio of 1.25 and a lead length of 12 inches. It was found that the turbulent flow data could best be characterized by the energy parameter C/sub 1L/=.106, which is 9% higher than the value from the correlation of Chiu et al. Chiu's correlation was developed on a data base of 61 and 91 pins. The spread of existing data about the correlation is +- 25%, but the error band on our data is expected to be less (approx. +- 10% since injection depth effects were not previously considered). This result is consistent with the concept of increased swirl flow in larger bundles

Molybdenum-99-producing 37-element fuel bundle neutronically and thermal-hydraulically equivalent to a standard CANDU fuel bundle

Energy Technology Data Exchange (ETDEWEB)

Nichita, E., E-mail: Eleodor.Nichita@uoit.ca; Haroon, J., E-mail: Jawad.Haroon@uoit.ca

2016-10-15

Highlights: • A 37-element fuel bundle modified for {sup 99}Mo production in CANDU reactors is presented. • The modified bundle is neutronically and thermal-hydraulically equivalent to the standard bundle. • The modified bundle satisfies all safety criteria satisfied by the standard bundle. - Abstract: {sup 99m}Tc, the most commonly used radioisotope in diagnostic nuclear medicine, results from the radioactive decay of {sup 99}Mo which is currently being produced at various research reactors around the globe. In this study, the potential use of CANDU power reactors for the production of {sup 99}Mo is investigated. A modified 37-element fuel bundle, suitable for the production of {sup 99}Mo in existing CANDU-type reactors is proposed. The new bundle is specifically designed to be neutronically and thermal-hydraulically equivalent to the standard 37-element CANDU fuel bundle in normal, steady-state operation and, at the same time, be able to produce significant quantities of {sup 99}Mo when irradiated in a CANDU reactor. The proposed bundle design uses fuel pins consisting of a depleted-uranium centre surrounded by a thin layer of low-enriched uranium. The new molybdenum-producing bundle is analyzed using the lattice transport code DRAGON and the diffusion code DONJON. The proposed design is shown to produce 4081 six-day Curies of {sup 99}Mo activity per bundle when irradiated in the peak-power channel of a CANDU core, while maintaining the necessary reactivity and power rating limits. The calculated {sup 99}Mo yield corresponds to approximately one third of the world weekly demand. A production rate of ∼3 bundles per week can meet the global demand of {sup 99}Mo.

Sodium Loop Safety Facility W-2 experiment fuel pin rupture detection system

International Nuclear Information System (INIS)

Hoffman, M.A.; Kirchner, T.L.; Meyers, S.C.

1980-05-01

The objective of the Sodium Loop Safety Facility (SLSF) W-2 experiment is to characterize the combined effects of a preconditioned full-length fuel column and slow transient overpower (TOP) conditions on breeder reactor (BR) fuel pin cladding failures. The W-2 experiment will meet this objective by providing data in two technological areas: (1) time and location of cladding failure, and (2) early post-failure test fuel behavior. The test involves a seven pin, prototypic full-length fast test reactor (FTR) fuel pin bundle which will be subjected to a simulated unprotected 5 cents/s reactivity transient overpower event. The outer six pins will provide the necessary prototypic thermal-hydraulic environment for the center pin

Development of disassembly and pin chopping technology for FBR spent fuels

International Nuclear Information System (INIS)

Kobayashi, Tsuguyuki; Namba, Takashi; Kawabe, Yukinari; Washiya, Tadahiro

2008-01-01

Japan Atomic Power Company (JAPC) and Japan Atomic Energy Agency (JAEA) have been developing fuel disassembly and fuel pin chopping systems for a future Japanese commercial FBR. At first, the wrapper tube is cut by the slit-cut to pull it out, then the fuel pins are cut by the crop-cut at their end-plugs to separate them from the entrance nozzle. The pins are transferred to the magazine of the chopping machine. A series of tests were performed to develop this procedure. As the result of mechanical cutting tests, the CBN wheel was selected. The slit-cut tests were carried out to evaluated the cutting performance of the wheel. The wrapper tube is normally slit-cut in the circumferential direction. One CBN wheel could cut more than 5 fuel assemblies in this direction. The slit-cut in the axial direction is prepared as provision when the tube is difficult to put out. More work is needed to cut 5mm thick PNC-FMS plate in this direction without damaging the pins beneath it. As the result of the crop-cut tests of end-plugs made of ODS steel, the CBN wheel could cut the 61 pin bundle by two strokes. More work is needed to cut the 217 pin bundle. Fuel pin handling tests were performed to transfer them from the disassembly machine to the chopping machine. The Saucer tray was selected to receive the disassembled pins. All the pins were transferred and loaded into a magazine of the chopping machine. Fuel pin loading tests were conducted to optimize the magazine configuration to make the chopping length within 1.0±0.5 cm. In order to decrease the disturbance during chopping, the width of the magazine was adjusted to be 12 cm and installation of a height adjuster is favourable to control the free space above the pins. (author)

Sodium Loop Safety Facility W-2 experiment fuel pin rupture detection system. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Hoffman, M.A.; Kirchner, T.L.; Meyers, S.C.

1980-05-01

The objective of the Sodium Loop Safety Facility (SLSF) W-2 experiment is to characterize the combined effects of a preconditioned full-length fuel column and slow transient overpower (TOP) conditions on breeder reactor (BR) fuel pin cladding failures. The W-2 experiment will meet this objective by providing data in two technological areas: (1) time and location of cladding failure, and (2) early post-failure test fuel behavior. The test involves a seven pin, prototypic full-length fast test reactor (FTR) fuel pin bundle which will be subjected to a simulated unprotected 5 cents/s reactivity transient overpower event. The outer six pins will provide the necessary prototypic thermal-hydraulic environment for the center pin.

BDI behavior evaluation of an upgraded Monju core and a demonstration core. (1) Plans for the out of pile bundle compressive tests for large diameter pins

International Nuclear Information System (INIS)

Ichikawa, Shoichi; Haga, Hiroyuki; Katsuyama, Kozo; Uwaba, Tomoyuki; Maeda, Koji; Nishinoiri, Kenji

2012-07-01

The life of FBR (Fast Breeder Reactor) fuel assembly is restricted by BDI (Bundle-Duct Interaction). Therefore, it is very important to carry out the out pile bundle compressive tests which can imitate BDI, in order to evaluate BDI behavior. The target of the conventional BDI behavior was small diameter pins (φ6.5mm) for fuel pellets which were used with the assembly of Monju (the Monju prototype fast breeder reactor) etc. Furthermore by an upgraded Monju core and a demonstration core, adoption of large diameter pins for the holler annular pellets is planned. Therefore, it was necessary to carry out BDI evaluation of a large diameter pin. Then, the plans for out of pile bundle compressive test for large diameter pins were are reported. (author)

Creep relaxation of fuel pin bending and ovalling stresses

International Nuclear Information System (INIS)

Chan, D.P.; Jackson, R.J.

1979-06-01

Analytical methods for calculating fuel pin cladding bending and ovalling stresses due to pin bundle-duct mechanical interaction taking into account nonlinear creep are presented. Calculated results are in close agreement with finite element results by MARC-CDC program. The methods are used to investigate the effect of creep on the FTR fuel cladding bending and ovalling stresses. It is concluded that the cladding of 316 SS 20% CW and reference design has high creep rates in the FTR core region to keep the bending and ovalling stresses to low levels

Thermal/hydraulic bowing stability analysis of grid-supported multi-pin bundles with differential swelling and irradiation creep

International Nuclear Information System (INIS)

McAreavey, G.

1977-01-01

Azimuthal variations of clad temperature in fuel pin bundles leads to pin bowing by differential thermal expansion. During irradiation in a fast flux further possibly more severe bowing is caused by differential neutron induced voidage swelling, which, being temperature sensitive, will also vary azimuthally. The problem of pin bowing in a fuel element cluster involves consideration of the thermal/hydraulic behaviour, allowing for both inherent and induced clad temperature non-uniformities, coupled with the restrained bowing behaviour, including differential thermal expansion, differential swelling, and irradiation creep. All pins must be considered simultaneously. In the temperature and stress ranges of interest thermal creep may be neglected. An existing computer code, IAMBIC solves the zero time thermal bowing problem for a cluster of up to 61 pins on hexagonal pitch, with up to 21 supports at arbitrary axial spacing. The present paper describes the basis of TRIAMBIC, a time dependent code which analyses the irradiation induced effects in fuel pin bunbles due to fast neutrons. (Auth.)

FFTF/IEM [Fast Flux Test Facility/Interim Examination and Maintenance] cell fuel pin weighing system: Remote maintenance design considerations

International Nuclear Information System (INIS)

Gibbons, P.W.

1986-06-01

A Fuel Pin Weighing Machine has been developed for use in the Fast Flux Test Facility (FFTF) Interim Examination and Maintenance (IEM) Cell to assist in identifying an individual breached fuel pin from its fuel assembly pin bundle. Optimum configuration for remote maintenance was a major consideration in the design of each element of the Pin Weighing System

Evaluation of the linear power of HANARO test fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Lee, Choong Sung; Seo, C. G.; Lee, B. C.; Kim, H. R

2001-02-01

The HANARO fuel was developed by AECL and it is configured in a bundle of rods containing uranium silicide. AECL has conducted a variety of tests using specimen in order to achieve its qualification and licensing and the highest linear power was evaluated to be 112.8kW/m. In design stage of HANARO, the best estimated maximum linear power at hot spot was found to occur in the transition core from the initial to the equilibrium and its value was 108kW/m, which exceeds 112.8kW/m if the physics uncertainty of the HANARO nuclear design model is taken into account. Consequently, the licensing body issued the conditional permit to operate HANARO and the fuel integrity at the linear power higher than 112.8kW/m was requested to be confirmed through irradiation tests by realizing its repeatability. Hereby, KAERI designed uninstrumented and instrumented test fuel bundles and conducted their burnup tests. In parallel with the tests, the nuclear design model has been revised and updated to enable us to pursue the pin-by-pin power history. This report describes the best estimated power history of the test fuel bundles using the revised model. In conclusion, HANARO fuel keeps its integrity at power condition greater than 120kW/m.

Fabrication of PWR fuel assembly and CANDU fuel bundle

International Nuclear Information System (INIS)

Lee, G.S.; Suh, K.S.; Chang, H.I.; Chung, S.H.

1980-01-01

For the project of localization of nuclear fuel fabrication, the R and D to establish the fabrication technology of CANDU fuel bundle as well as PWR fuel assembly was carried out. The suitable boss height and the prober Beryllium coating thickness to get good brazing condition of appendage were studied in the fabrication process of CANDU fuel rod. Basic Studies on CANLUB coating method also were performed. Problems in each fabrication process step and process flow between steps were reviewed and modified. The welding conditions for top and bottom nozzles, guide tube, seal and thimble screw pin were established in the fabrication processes of PWR fuel assembly. Additionally, some researches for a part of PWR grid brazing problems are also carried out

Fluid-mixing studies in a hexagonal 61-pin wire-wrapped rod bundle

International Nuclear Information System (INIS)

Symolon, P.D.; Todreas, N.E.

1981-02-01

Mixing, pressure drop, and flow split experiments were performed on a 61 pin LMFBR fuel bundle with a pitch to diameter ratio of 1.25, and lead lengths of 6 and 12 inches. The mixing results obtained from salt injection experiments were found to depend on injection depth. The deeper injection is expected to give the more accurate results. The pressure drop data was presented as friction factor versus Reynolds number, and the results were compared to the correlation of Hawley. The flowsplit data presented was flawed by corroded bundle walls, but some insight was obtained on the effect of rough surfaces on flowsplit, and how to account for its effect in the correlations

FFTF [Fast Flux Test Facility]/IEM [Interim Examination and Maintenance] Cell Fuel Pin Weighing System

International Nuclear Information System (INIS)

Gibbons, P.W.

1987-09-01

A Fuel Pin Weighing Machine has been developed for use in the Fast Flux Test Facility (FFTF) Interim Examination and Maintenance (IEM) Cell to assist in identifying an individual breached fuel pin from its fuel assembly pin bundle. A weighing machine, originally purchased for use in the Fuels and Materials Examination Facility (FMEF) at Hanford, was used as the basis for the IEM Cell system. Design modifications to the original equipment were centered around: 1) adapting the FMEF machine for use in the IEM Cell and 2) correcting operational deficiencies discovered during functional testing in the IEM Cell Mockup

Development and testing of high-performance fuel pin simulators for boiling experiments in liquid metal flow

International Nuclear Information System (INIS)

Casal, V.

1976-01-01

There are unknown phenomena, about local and integral boiling events in the core of sodium cooled fast breeder reactors. Therefore at GfK depend out-of-pile boiling experiments have been performed using electrically heated dummies of fuel element bundles. The success of these tests and the amount of information derived from them depend exclusively on the successful simulation of the fuel pins by electrically heated rods as regards the essential physical properties. The report deals with the development and testing of heater rods for sodium boiling experiments in bundles including up to 91 heated pins

Effect of power variations across a fuel bundle and within a fuel element on fuel centerline temperature in PHWR bundles in uncrept and crept pressure tubes

International Nuclear Information System (INIS)

Onder, E.N.; Roubtsov, D.; Rao, Y.F.; Wilhelm, B.

2017-01-01

Highlights: • Pressure tube creep effect on fuel pin power and temperatures was investigated. • Noticeable effects were observed for 5.1% crept pressure tube. • Bundle eccentricity effect on power variations was insignificant for uncrept channels. • Difference of 112 °C was observed between top & bottom elements in 5.1% crept channel. • Not discernible fission gas release was expected with temperature difference of 112 °C. - Abstract: The neutron flux and fission power profiles through a fuel bundle and across a fuel element are important aspects of nuclear fuel analysis in multi-scale/multi-physics modelling of Pressurized Heavy Water Reactors (PHWRs) with advanced fuel bundles. Fuel channels in many existing PHWRs are horizontal. With ageing, pressure tubes creep and fuel bundles in these pressure tubes are eccentrically located, which results in an asymmetric coolant flow distribution between the top and bottom of the fuel bundles. The diametral change of the pressure tube due to creep is not constant along the fuel channel; it reaches a maximum in the vicinity of the maximum neutron flux location. The cross-sectional asymmetric positioning of fuel bundles in a crept pressure tube contributes to an asymmetric power distribution within a ring of fuel elements. Modern reactor physics lattice codes (such as WIMS-AECL) are capable of predicting the details of power distribution from basic principles. Thermalhydraulics subchannel codes (such as ASSERT-PV) use models to describe inhomogeneous power distribution within and across fuel elements (e.g., flux tilt model, different powers in different ring elements, or radial power profiles). In this work, physics and thermalhydraulics codes are applied to quantify the effect of eccentricity of a fuel bundle on power variations across it and within a fuel element, and ultimately on the fuel temperature distribution and fuel centerline temperature, which is one of the indicators of fuel performance under normal

Seven pin bundle fast top tests L01 and L02

International Nuclear Information System (INIS)

Davies, A.L.; Bowen, G.R.; Herbert, R.; Kear, K.L.; Tylka, J.P.; Holland, J.W.

1984-01-01

Tests L01 and L02 were the first two seven pin bundle tests in the PFR/TREAT program of fuel failure tests carried out jointly by the US and the UK. The two tests were on bottom plenum annular pellet mixed oxide fuel clad in 316 stainless steel. L01 used fresh fuel, while L02 used PFR irradiated 4% burn-up fuel, to determine any differences in the failure mechanism and subsequent fuel behavior due to irradiation. They were performed in flowing sodium in the Mark IIIA version of a TREAT integral loop. Both were fast transient overpower (TOP) tests intended to simulate 5 $/s reactivity ramp hypothetical accidents in a large fast reactor. The test objectives were to obtain information on fuel motion in the central hole before failure, the time and location of cladding failures, and material motion in the channel after failure, having particular regard to the effect of irradiation

RANS based CFD methodology for a real scale 217-pin wire-wrapped fuel assembly of KAERI PGSFR

Energy Technology Data Exchange (ETDEWEB)

Jeong, Jae-Ho, E-mail: jhjeong@kaeri.re.kr [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseoung-gu, Daejeon (Korea, Republic of); Song, Min-Seop [Department of Nuclear Engineering, Seoul National University, 559 Gwanak-ro, Gwanak-gu, Seoul (Korea, Republic of); Lee, Kwi-Lim [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseoung-gu, Daejeon (Korea, Republic of)

2017-03-15

Highlights: • This paper presents a suitable way for a practical RANS based CFD methodology which is applicable to real scale 217-pin wire-wrapped fuel assembly of KAERI PGSFR. • A key point of differentiation of the RANS based CFD methodology in this study is adapting an innovative grid generation method using a fortran based in-house code with a GGI function in a general-purpose commercial CFD code, CFX. • The RANS based CFD methodology is implemented with high resolution scheme and SST turbulence model in the 7-pin 37-pin, and 127-pin wire-wrapped fuel assembly of PNC and JNC. Furthermore, the RANS based CFD methodology can be successfully extended to the real scale 217-pin wire-wrapped fuel bundles of KAERI PGSFR. • Three-dimensional thermal-hydraulic characteristics have been also investigated briefly. - Abstract: This paper presents a suitable way for a practical RANS (Reynolds Averaged Navier-Stokes simulation) based CFD (Computational Fluid Dynamics) methodology which is applicable to real scale 217-pin wire-wrapped fuel assembly of KAERI (Korea Atomic Energy Research Institute) PGSFR (Prototype Gen-IV Sodium-cooled Fast Reactor). The main purpose of the current study is to support license issue for the KAERI PGSFR core safety and to elucidate thermal-hydraulic characteristics in a 217-pin wire-wrapped fuel assembly of KAERI PGSFR. A key point of differentiation of the RANS based CFD methodology in this study is adapting an innovative grid generation method using a fortran based in-house code with a GGI (General Grid Interface) function in a general-purpose commercial CFD code, CFX. The innovative grid generation method with GGI function can achieve to simulate a real wire shape with minimizing cell skewness. The RANS based CFD methodology is implemented with high resolution scheme in convection term and SST (Shear Stress Transport) turbulence model in the 7-pin 37-pin, and 127-pin wire-wrapped fuel assembly of PNC (Power reactor and Nuclear fuel

Experimental determination of the local temperature distribution in the cladding tubes of a sodium-cooled pin bundle caused by grid spacers

International Nuclear Information System (INIS)

Moeller, R.; Tschoeke, H.

1980-01-01

The cladding tubes of reactor core elements are highly stressed structural elements. Their careful design includes the following: (a) the mathematical determination of the maximum cladding tube temperatures; (b) the determination of the maximum permissible fatigue strengths and creep strains of the materials; and (c) the safety distance between the nominal cladding tube hot spots and the permissible extreme cladding tube temperature. The maximum cladding tube temperatures occur on the top edge of the core and, due to radial power gradients, in the wrapper-wall region of a pin bundle. If grid spacers are now used for fixing the pins as in the SNR fuel elements, a careful check must be made of whether and to what degree temperature peaks in the region of the supports have an influence on the cladding tube design. Initial experimental investigations on a sodium-cooled pin bundle model of the SNR-300 fuel element were carried out to throw light on these special problems. This is reported in the following together with the results so far obtained. (U.K.)

Fuel temperature characteristics of the 37-element and CANFLEX fuel bundle

International Nuclear Information System (INIS)

Bae, Jun Ho; Rho, Gyu Hong; Park, Joo Hwan

2009-10-01

This report describes the fuel temperature characteristics of CANFLEX fuel bundles and 37-element fuel bundles for a different burnup of fuel. The program was consisted for seeking the fuel temperature of fuel bundles of CANFLEX fuel bundles and 37-element fuel bundles by using the method in NUCIRC. Fuel temperature has an increasing pattern with the burnup of fuel for CANFLEX fuel bundles and 37-element fuel bundles. For all the case of burnup, the fuel temperature of CANFLEX fuel bundles has a lower value than that of 37-element fuel bundles. Especially, for the high power channel, the CANFLEX fuel bundles show a lower fuel temperature as much as about 75 degree, and the core averaged fuel temperature has a lower fuel temperature of about 50 degree than that of 37-element fuel bundles. The lower fuel temperature of CANFLEX fuel bundles is expected to enhance the safety by reducing the fuel temperature coefficient. Finally, for each burnup of CANFLEX fuel bundles and 37-element fuel bundles, the equation was present for predicting the fuel temperature of a bundle in terms of a coolant temperature and bundle power

Thermal-hydraulic characteristics of reacting zone for TWR bundles based on CFD method

International Nuclear Information System (INIS)

Lu Chuan; Yan Mingyu; Lu Jianchao

2013-01-01

Thermal-hydraulic characteristics of reacting zone for TWR (travelling wave reactor) bundles were analysed by CFD method. The calculation results of 7, 19 and 37 fuel pin bundles show the similar characteristics. The hot coolant seems to congregate into the centre as flowing to the downstream area. The high temperature coolant always distributes in the inner area while the temperature shows distinct gradation in the outer area. The temperature difference is more than 100 ℃ for the bundle whose diameter is about 26 cm. The major temperature gradations mainly locate in the outermost fuel rods of two circles while other circles show much smaller temperature gradients. This conclusion is estimated to be true for more fuel pin bundles such as 217 fuel pin bundles. The fuel assembly structure of the existing TWR design should be optimized in future. (authors)

Safety assessment for the CANFLEX-NU fuel bundles with respect to the 37-element fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Suk, H. C.; Lim, H. S. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-11-01

The KAERI and AECL have jointly developed an advanced CANDU fuel, called CANFLEX-NU fuel bundle. CANFLEX 43-element bundle has some improved features of increased operating margin and enhanced safety compared to the existing 37-element bundle. Since CANFLEX fuel bundle is designed to be compatible with the CANDU-6 reactor design, the behaviour in the thermalhydraulic system will be nearly identical with 37-element bundle. But due to different element design and linear element power distribution between the two bundles, it is expected that CANFLEX fuel behaviour would be different from the behaviour of the 37-element fuel. Therefore, safety assessments on the design basis accidents which result if fuel failures are performed. For all accidents selected, it is observed that the loading of CANFLEX bundle in an existing CANDU-6 reactor would not worsen the reactor safety. It is also predicted that fission product release for CANFLEX fuel bundle generally is lower than that for 37-element bundle. 3 refs., 2 figs., 2 tabs. (Author)

Two-dimensional steady-state thermal and hydraulic analysis code for prediction of detailed temperature fields around distorted fuel pin in LMFBR assembly: SPOTBOW

International Nuclear Information System (INIS)

Shimizu, T.

1983-01-01

SPOTBOW computer program has been developed for predicting detailed temperature and turbulent flow velocity fields around distorted fuel pins in LMFBR fuel assemblies, in which pin to pin and pin to wrapper tube contacts may occur. The present study started from the requirement of reactor core designers to evaluate local hot spot temperature due to the wire contact effect and the pin bowing effect on cladding temperature distribution. This code calculates for both unbaffled and wire-wrapped pin bundles. The Galerkin method and iterative procedure were used to solve the basic equations which govern the local heat and momentum transfer in turbulent fluid flow around the distorted pins. Comparisons have been made with cladding temperatures measured in normal and distorted pin bundle mockups to check the validity of this code. Predicted peak temperatures in the vicinity of wire contact point were somewhat higher than the measured values, and the shape of the peaks agreed well with measurement. The changes of cladding temperature due to the decrease of gap width between bowing pin and adjacent pin were predicted well

Vibration of fuel bundles

International Nuclear Information System (INIS)

Chen, S.S.

1975-06-01

Several mathematical models have been proposed for calculating fuel rod responses in axial flows based on a single rod consideration. The spacing between fuel rods in liquid metal fast breeder reactors is small; hence fuel rods will interact with one another due to fluid coupling. The objective of this paper is to study the coupled vibration of fuel bundles. To account for the fluid coupling, a computer code, AMASS, is developed to calculate added mass coefficients for a group of circular cylinders based on the potential flow theory. The equations of motion for rod bundles are then derived including hydrodynamic forces, drag forces, fluid pressure, gravity effect, axial tension, and damping. Based on the equations, a method of analysis is presented to study the free and forced vibrations of rod bundles. Finally, the method is applied to a typical LMFBR fuel bundle consisting of seven rods

Characteristics of liquid and boiling sodium flows in heating pin bundles

International Nuclear Information System (INIS)

Menant, Bernard

1976-01-01

This study is related to cooling accidents which could occur in sodium cooled fast reactors. Thermo-hydraulic aspects of boiling experiments in pin bundles with helical wire-wrap spacer systems, in the case of undamaged geometries, are analyzed. Differences and analogies in the behavior of multi-rod bundle flows and one-dimensional channel flows are studied. A boiling model is developed for bundle geometries, and predictions obtained with the FLICA code using this models are presented. These predictions are compared with experimental results obtained in a water 19-rod bundle. Then, results of sodium boiling experiments through a 19-rod bundle are interpreted. Both cases of high power and reduced power are envisaged. (author) [fr

Design report for an annular fuel element for accommodation of a carbide test bundle on the ring position of the KNK II/2 test zone

International Nuclear Information System (INIS)

Haefner, H.E.

1982-03-01

This report describes an annular oxide element with Mark II rods for accommodation of a 19-pin carbide test bundle on position 201 in the test zone of the second core of KNK II as well as its behavior during the period of operation. The ring element comprises within a driver wrapper in three rows of pins 102 fuel pins of 7.6 mm diameter and six structural rods for fixing the spark eroded spacers. The report deals with the ring element with its individual components fuel rod, bundle, wrappers, head and foot and describes methods, criteria and results concerning the design. The carbide test bundle to be accommodated by the annular carrier element will be treated in a separate report. The loadability of the annular element with its components is demonstrated by generally valid standards for strength criteria

Improvement of the computing speed of the FBR fuel pin bundle deformation analysis code 'BAMBOO'

International Nuclear Information System (INIS)

Ito, Masahiro; Uwaba, Tomoyuki

2005-04-01

JNC has developed a coupled analysis system of a fuel pin bundle deformation analysis code 'BAMBOO' and a thermal hydraulics analysis code ASFRE-IV' for the purpose of evaluating the integrity of a subassembly under the BDI condition. This coupled analysis took much computation time because it needs convergent calculations to obtain numerically stationary solutions for thermal and mechanical behaviors. We improved the computation time of the BAMBOO code analysis to make the coupled analysis practicable. 'BAMBOO' is a FEM code and as such its matrix calculations consume large memory area to temporarily stores intermediate results in the solution of simultaneous linear equations. The code used the Hard Disk Drive (HDD) for the virtual memory area to save Random Access Memory (RAM) of the computer. However, the use of the HDD increased the computation time because Input/Output (I/O) processing with the HDD took much time in data accesses. We improved the code in order that it could conduct I/O processing only with the RAM in matrix calculations and run with in high-performance computers. This improvement considerably increased the CPU occupation rate during the simulation and reduced the total simulation time of the BAMBOO code to about one-seventh of that before the improvement. (author)

Cesium chemistry in GCFR fuel pins

International Nuclear Information System (INIS)

Fee, D.C.; Johnson, C.E.

1979-01-01

The fuel rod design for the Gas Cooled Fast-Breeder Reactor (GCFR) is similar to that employed for the Liquid Metal Fast Breeder Reactor (LMFBR) with the exception of the unique features inherent to the use of helium as the coolant. These unique design features include the use of (1) vented and pressure-equalized fuel rods, and (2) ribbed cladding along 75% of the fuel section. The former design feature enables reduction in cladding thickness and prevention of possible creep collapse of the cladding due to the high coolant pressure (8.5 MPa). The latter design feature brings about improved heat transfer characteristics. Each GCFR fuel rod is vented to a manifold whereby gaseous fission products diffusing out of the fuel pin are retained on charcoal traps. As a result, the internal pressure of a GCFR fuel pin does not increase during irradiation. In addition, the venting system also maintains the pressure within the fuel pin slightly below (0.3 to 0.5 MPa) the coolant pressure outside the fuel pin. Consequently, should a breach occur in the cladding, helium flows into the breached fuel pin thereby minimizing fission product contamination of the coolant. These desirable aspects of a GCFR fuel pin can be maintained only as long as axial gas transport paths are available and operating within the fuel pin

Three-dimensional flow phenomena in a wire-wrapped 37-pin fuel bundle for SFR

Energy Technology Data Exchange (ETDEWEB)

Jeong, Jae Ho; Yoo, Jin; Lee, Kwi Lim; Ha, Kwi Seok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-08-15

Three-dimensional flow phenomena in a wire-wrapped 37-pin fuel assembly mock-up of a Japanese loop-type sodium-cooled fast reactor, Monju, were investigated with a numerical analysis using a general-purpose commercial computational fluid dynamics code, CFX. Complicated and vortical flow phenomena in the wire-wrapped 37-pin fuel assembly were captured by a Reynolds-averaged Navier-Stokes flow simulation using a shear stress transport turbulence model. The main purpose of the current study is to understand the three-dimensional complex flow phenomena in a wire-wrapped fuel assembly to support the license issue for the core design. Computational fluid dynamics results show good agreement with friction factor correlation models. The secondary flow in the corner and edge subchannels is much stronger than that in an interior subchannel. The axial velocity averaged in the corner and edge subchannels is higher than that averaged in the interior subchannels. Three-dimensional multiscale vortex structures start to be formed by an interaction between secondary flows around each wire-wrapped pin. Behavior of the large-scale vortex structures in the corner and edge subchannels is closely related to the relative position between the hexagonal duct wall and the helically wrapped wire spacer. The small-scale vortex is axially developed in the interior subchannels. Furthermore, a driving force on each wire spacer surface is closely related to the relative position between the hexagonal duct wall and the wire spacer.

Automated fuel pin loading system

Science.gov (United States)

Christiansen, D.W.; Brown, W.F.; Steffen, J.M.

An automated loading system for nuclear reactor fuel elements utilizes a gravity feed conveyor which permits individual fuel pins to roll along a constrained path perpendicular to their respective lengths. The individual lengths of fuel cladding are directed onto movable transports, where they are aligned coaxially with the axes of associated handling equipment at appropriate production stations. Each fuel pin can be be reciprocated axially and/or rotated about its axis as required during handling steps. The fuel pins are inerted as a batch prior to welding of end caps by one of two disclosed welding systems.

Development of a numerical experimentation method for thermal hydraulics design and evaluation of high burn-up and innovative fuel pins

International Nuclear Information System (INIS)

Ninokata, Hisashi; Misawa, Takeharu; Baglietto, Emilio; Sorokin, A.P.; Maekawa, Isamu; Ohshima, Hiroyuki; Yamaguchi, Akira

2003-03-01

A method of large scale direct numerical simulation of turbulent flows in a high burn-up fuel pin bundle is proposed to evaluate wall shear stress and temperature distributions on the pin surfaces as well as detailed coolant velocity and temperature distributions inside subchannels under various thermal hydraulic conditions. This simulation is aimed at providing a tool to confirm margins to thermal hydraulics design limits of the nuclear fuels and at the same time to be used in design-by-analysis approaches. The method will facilitate thermal hydraulic design of high performance LMFR core fuels characterized by high burn-up, ultra long life, high reliable and safe performances, easiness of operation and maintenance, minimization of radio active wastes, without much relying on such empirical approach as hot spot factor and sub-factors, and above all the high cost mock up experiments. A pseudo direct numerical simulation of turbulence (DNS) code is developed, first on the Cartesian coordinates and then on the curvilinear boundary fit coordinates that enables us to reproduce thermal hydraulics phenomena in such a complicated flow channel as subchannels in a nuclear fuel pin assembly. The coordinate transformation is evaluated and demonstrated to yield correct physical quantities by carrying out computations and comparisons with experimental data with respect to the distributions of various physical quantities and turbulence statistics for fluid flow and heat transfers in various kinds of simple flow channel geometry. Then the boundary fitted pseudo DNS for flows inside an infinite pin array configuration is carried out and compared with available detailed experimental data. In parallel similar calculations are carried out using a commercial code STAR-CD to cross-check the DNS performances. As a results, the pseudo DNS showed reasonable comparisons with experiments as well as the STAR-CD results. Importance of the secondary flow influences is emphasized on the momentum

Automated system for loading nuclear fuel pins

International Nuclear Information System (INIS)

Marshall, J.L.

1983-10-01

A completely automatic and remotely controlled fuel pin fabrication system is being designed by the Westinghouse Hanford Company. The Pin Operations System will produce fuel pins for the Fast Flux Test Facility (FFTF) and the Clinch River Breeder Reactor Plant (CRBRP). The system will assemble fuel pin components into cladding tubes in a controlled environment. After fuel loading, the pins are filled with helium, the tag gas capsules are inserted, and the top end cap welded. Following welding, the pins are surveyed to assure they are free of contamination and then the pins are helium leak tested

Transient survivability of LMR oxide fuel pins

International Nuclear Information System (INIS)

Weber, E.T.; Pitner, A.L.; Bard, F.E.; Culley, G.E.; Hunter, C.W.

1986-01-01

Fuel pin integrity during transient events must be assessed for both the core design and safety analysis phases of a reactor project. A significant increase in the experience related to limits of integrity for oxide fuel pins in transient overpower events has been realized from testing of fuel pins irradiated in FFTF and PFR. Fourteen FFTF irradiated fuel pins were tested in TREAT, representing a range of burnups, overpower ramp rates and maximum overpower conditions. Results of these tests along with similar testing in the PFR/TREAT program, provide a demonstration of significant safety margins for oxide fuel pins. Useful information applied in analytical extrapolation of fuel pin test data have been developed from laboratory transient tests on irradiated fuel cladding (FCTT) and on unirradiated fuel pellet deformation. These refinements in oxide fuel transient performance are being applied in assessment of transient capabilities of long lifetime fuel designs using ferritic cladding

Fuel pin transfer tool

International Nuclear Information System (INIS)

Patenaude, R. S.

1985-01-01

A fuel pin transfer tool has a latching device of the collet type attached to a first member movable vertically through a long work stroke enabling a fuel pin in an under water assembly to be engaged and withdrawn therefrom or placed therein and released. The latching device has a collet provided with a plurality of resilient fingers having cam portions normally spaced apart to receive the upper end of a fuel pin between them and a second member, movable vertically through a short stroke relative to the first member is provided with cam portions engageable with those of the fingers and is yieldably and resiliently held in a raised position in which its cam portions engage those of the fingers and force the fingers into their pin-gripping positions. When a predetermined force is applied to the second member, it is so moved that its cam portions are disengaged from the cam portions of the fingers permitting the latter to move into their normal relationship in which a gripped pin is released or another pin received but with their pin-gripping relationship positively re-established and maintained once the force on the tubular member is lessened. Movement of the first member in either direction and movement of the second member into its raised position is attended by forces inadequate to affect the integrity of fuel pin cladding. That force is applied in the preferred embodiment, by a power operated actuator which is within the upper portion of a housing and, in the preferred embodiment, carried by the long stroke member but always in the upper housing portion which is of a material sufficiently translucent to enable the actuator to be observed throughout the work stroke and is sufficiently light in weight to prevent the tool from being top heavy

The Effect of Material Homogenization in Calculating the Gamma-Ray dose from Spent PWR Fuel Pins in an Air Medium

International Nuclear Information System (INIS)

TH Trumbull

2005-01-01

The effect of material homogenization on the calculated dose rate was studied for several arrangements of typical PWR spent fuel pins in an air medium using the Monte Carlo code, MCNP. The models analyzed increased in geometric complexity, beginning with a single fuel pin, progressing to ''small'' lattices, i.e., 3x3, 5x5, 7x7 fuel pins, and culminating with a full 17x17 pin PWR bundle analysis. The fuel pin dimensions and compositions were taken directly from a previous study and efforts were made to parallel this study by specifying identical flux-to-dose functions and gamma-ray source spectra. The analysis shows two competing components to the overall effect of material homogenization on calculated dose rate. Homogenization of pin lattices tends to lower the effect of radiation ''channeling'' but increase the effect of ''source redistribution.'' Depending on the size of the lattice and location of the detectors, the net effect of material homogenization on dose rate can be insignificant or range from a 6% decrease to a 35% increase relative to the detailed geometry model

CANFLEX fuel bundle impact test

International Nuclear Information System (INIS)

Chang, Seok Kyu; Chung, C. H.; Park, J. S.; Hong, S. D.; Kim, B. D.

1997-08-01

This document outlines the test results for the impact test of the CANFLEX fuel bundle. Impact test is performed to determine and verify the amount of general bundle shape distortion and defect of the pressure tube that may occur during refuelling. The test specification requires that the fuel bundles and the pressure tube retain their integrities after the impact test under the conservative conditions (10 stationary bundles with 31kg/s flow rate) considering the pressure tube creep. The refuelling simulator operating with pneumatic force and simulated shield plug were fabricated and the velocity/displacement transducer and the high speed camera were also used in this test. The characteristics of the moving bundle (velocity, displacement, impacting force) were measured and analyzed with the impact sensor and the high speed camera system. The important test procedures and measurement results were discussed as follows. 1) Test bundle measurements and the pressure tube inspections 2) Simulated shield plug, outlet flange installation and bundle loading 3) refuelling simulator, inlet flange installation and sensors, high speed camera installation 4) Perform the impact test with operating the refuelling simulator and measure the dynamic characteristics 5) Inspections of the fuel bundles and the pressure tube. (author). 8 refs., 23 tabs., 13 figs

Dimensional measurement of fresh fuel bundle for CANDU reactor

International Nuclear Information System (INIS)

Jo, Chang Keun; Cho, Moon Sung; Suk, Ho Chun; Koo, Dae Seo; Jun, Ji Su; Jung, Jong Yeob

2005-01-01

This report describes the results of the dimensional measurement of fresh fuel bundles for the CANDU reactor in order to estimate the integrity of fuel bundle in two-phase flow in the CANDU-6 fuel channel. The dimensional measurements of fuel bundles are performed by using the 'CANDU Fuel In-Bay Inspection and Dimensional Measurement System', which was developed by this project. The dimensional measurements are done from February 2004 to March 2004 in the CANDU fuel storage of KNFC for the 36 fresh fuel bundles, which are produced by KNFC and are waiting for the delivery to the Wolsong-3 plant. The detail items of dimensional measurements are included fuel rod and bearing pad profiles of the outer ring in fuel bundle, diameter of fuel bundle, bowing of fuel bundle, fuel rod length, and surface profile of end plate profile. The measurement data will be compared with those of the post-irradiated bundles cooled in Wolsong-3 NPP spent fuel pool by using the same bundles and In-Bay Measurement System. So, this analysis of data will be applied for the evaluation of fuel bundle integrity in two-phase flow of the CANDU-6 fuel channel

Suspension scheme for fuel pin

International Nuclear Information System (INIS)

Butts, C.E.; Gray, H.C.

1975-01-01

A description is presented of a nuclear fuel pin suspension arrangement comprising, in combination, a rod; a first beam member connected to said rod at one end; a plurality of parallel-spaced slidable fuel support plates attached to said first beam member, the longitudinal axis of first beam member being perpendicular to the longitudinal axis of each of said fuel support plates, a first coupling means disposed along the length of the first beam member for permitting slidable fuel support plates parallel movement with respect to the longitudinal axis of said first beam member, a second coupling means located at one end of each of slidable fuel plates for slidably engaging first coupling means of first beam member, a second beam member connected to the other end of each of parallel-spaced slidable fuel support plates and providing an extension, second beam member being provided with a third coupling means disposed along the length of second beam member at one end thereof; and a plurality of fuel pins provided with a fourth coupling means located at one end of each fuel pin for slidably engaging third coupling means of second beam member to permit each fuel pin parallel movement with respect to the longitudinal axis of second beam member. (U.S.)

Hydraulic characteristics of HANARO fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Cho, S; Chung, H J; Chun, S Y; Yang, S K; Chung, M K [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

This paper presents the hydraulic characteristics measured by using LDV (Laser Doppler Velocimetry) in subchannels of HANARO, KAERI research reactor, fuel bundle. The fuel bundle consists of 18 axially finned rods with 3 spacer grids, which are arranged in cylindrical configuration. The effects of the spacer grids on the turbulent flow were investigated by the experimental results. Pressure drops for each component of the fuel bundle were measured, and the friction factors of fuel bundle and loss coefficients for the spacer grids were estimated from the measured pressure drops. Implications regarding the turbulent thermal mixing were discussed. Vibration test results measured by using laser vibrometer were presented. 9 refs., 12 figs. (Author)

Hydraulic characteristics of HANARO fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Cho, S.; Chung, H. J.; Chun, S. Y.; Yang, S. K.; Chung, M. K. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-12-31

This paper presents the hydraulic characteristics measured by using LDV (Laser Doppler Velocimetry) in subchannels of HANARO, KAERI research reactor, fuel bundle. The fuel bundle consists of 18 axially finned rods with 3 spacer grids, which are arranged in cylindrical configuration. The effects of the spacer grids on the turbulent flow were investigated by the experimental results. Pressure drops for each component of the fuel bundle were measured, and the friction factors of fuel bundle and loss coefficients for the spacer grids were estimated from the measured pressure drops. Implications regarding the turbulent thermal mixing were discussed. Vibration test results measured by using laser vibrometer were presented. 9 refs., 12 figs. (Author)

Thermal-hydraulic design calculations for the annular fuel element with replaceable test bundles (TOAST) on the test zone position 205 of KNK II/3

International Nuclear Information System (INIS)

Norajitra, P.

1984-10-01

Annular fuel elements are foreseen in KNK II as carrier elements for irradiation inserts and test bundles. For the third core a reloadable annular element on position 205 is foreseen, in which replaceable 19-pin test bundles (TOAST) shall be irradiated. The present report deals with the thermal-hydraulic design of the annular carrier element and the test bundle, whereby the test bundle required additional optimization. The code CIA has been used for the calculations. Start of irradiation of the subassembly is planned at the beginning of the third core operation. After optimization of the pin-spacer geometry in the test bundle, design calculations for both bundles were performed, whereby thermal coupling between both was taken into account. The calculated mass-flows and temperature distributions are given for the nominal and the eccentric element configuration. The calculated bundle pressure losses have been corrected according to experimental results [de

Development of nuclear fuel. Development of CANDU advanced fuel bundle

International Nuclear Information System (INIS)

Suk, Ho Chun; Hwang, Woan; Jeong, Young Hwan; Jung, Sung Hoon

1991-07-01

In order to develop CANDU advanced fuel, the agreement of the joint research between KAERI and AECL was made on February 19, 1991. AECL conceptual design of CANFLEX bundle for Bruce reactors was analyzed and then the reference design and design drawing of the advanced fuel bundle with natural uranium fuel for CANDU-6 reactor were completed. The CANFLEX fuel cladding was preliminarily investigated. The fabricability of the advanced fuel bundle was investigated. The design and purchase of the machinery tools for the bundle fabrication for hydraulic scoping tests were performed. As a result of CANFLEX tube examination, the tubes were found to be meet the criteria proposed in the technical specification. The dummy bundles for hydraulic scoping tests have been fabricated by using the process and tools, where the process parameters and tools have been newly established. (Author)

Fabrication, irradiation and post-irradiation examinations of MO2 and UO2 sphere-pac and UO2 pellet fuel pins irradiated in a PWR loop

International Nuclear Information System (INIS)

Linde, A. van der; Lucas Luijckx, H.J.B.; Verheugen, J.H.N.

1981-04-01

Three fuel pin bundles, R-109/1, 2 and 3, were irradiated in a PWR loop in the HFR at Petten during respectively 131, 57 and 57 effective full power days at average powers of approximately 39 kW.m -1 and at peak powers of approximately 60 kW.m -1 . The results of the post-irradiation examinations of these fuel bundles are presented. (Auth.)

Cesium migration in LMFBR fuel pins

International Nuclear Information System (INIS)

Karnesky, R.A.; Jost, J.W.; Stone, I.Z.

1978-10-01

The factors affecting the axial migration of cesium in mixed oxide fuel pins and the effects of cesium migration on fuel pin performance are examined. The development and application of a correlated model which will predict the occurrence of cesium migration in a mixed oxide (75 w/o UO 2 + 25 w/o PuO 2 ) fuel pins over a wide range of fabrication and irradiation conditions are described

Nuclear fuel pin controlled failure device

International Nuclear Information System (INIS)

Schlenker, L.D.

1975-01-01

Each fuel pin of a fuel assembly for a water-cooled nuclear reactor is provided with means for rupturing the cladding tube at a predetermined location if an abnormal increase in pressure of the gases present occurs due to a loss-of-coolant accident. Preferably all such rupture means are oriented to minimize the hydraulic resistance to the flow of emergency core coolant such as all rupture means pointing in the same direction. Rupture means may be disposed at different elevations in adjacent fuel pins and, further, fuel pins may be provided with two or more rupture means, one of which is in the upper portion of the fuel pin. Rupture means are mechanical as by providing a locally weakened condition of a controlled nature in the cladding. (U.S.)

Fuel-pin cladding transient failure strain criterion

International Nuclear Information System (INIS)

Bard, F.E.; Duncan, D.R.; Hunter, C.W.

1983-01-01

A criterion for cladding failure based on accumulated strain was developed for mixed uranium-plutonium oxide fuel pins and used to interpret the calculated strain results from failed transient fuel pin experiments conducted in the Transient Reactor Test (TREAT) facility. The new STRAIN criterion replaced a stress-based criterion that depends on the DORN parameter and that incorrectly predicted fuel pin failure for transient tested fuel pins. This paper describes the STRAIN criterion and compares its prediction with those of the stress-based criterion

FFTF fuel pin design bases and performance

International Nuclear Information System (INIS)

Cox, C.M.; Hanson, J.E.; Roake, W.E.; Slember, R.J.; Weber, C.E.; Millunzi, A.C.

1975-04-01

The FFTF fuel pin was conservatively designed to meet thermal and structural performance requirements in the categories normal operation, upset events, emergency events, and hypothetical, faulted events. The fuel pin operating limits consistent with these requirements were developed from a strong fuel pin irradiation testing program scoped to define the performance capability under relevant steady state and transient conditions. Comparison of the results of the irradiation testing program with design requirements indicates that the FFTF fuel pin can exceed its goal burnup of 80,000 MWd/MTM. (U.S.)

Mode of failure of LMFBR fuel pins

International Nuclear Information System (INIS)

Washburn, D.F.

1975-01-01

The objectives of the irradiation test described were to evaluate mixed-oxide fuel performance and to confirm the design adequacy of the FFTF fuel pins. After attainment of the initial objectives the irradiation of several of the original fuel pins was continued until a cladding breach occurred. The consequences of a cladding breach were evaluated by reconstituting the original 37-pin subassembly into two 19-pin subassemblies after a burnup at 50,000 MWd/MTM (5.2 a/o). The original pins were supplemented with fresh pins as necessary. Irradiation of the subassemblies was continued until a cladding breach occurred. Results are presented and discussed

Internal fuel pin oxidizer

International Nuclear Information System (INIS)

Andrews, M.G.

1978-01-01

A nuclear fuel pin has positioned within it material which will decompose to release an oxidizing agent which will react with the cladding of the pin and form a protective oxide film on the internal surface of the cladding

In-pool damaged fuel bundle recovery

International Nuclear Information System (INIS)

Piascik, T.G.; Patenaude, R.S.

1988-01-01

While preparing to rerack the Oyster Creek Nuclear Generating Station, GPU Nuclear had need to move a damaged fuel bundle. This bundle had no upper tie plate and could not be moved in the normal manner. GPU Nuclear formed a small, dedicated project team to disassemble, package and move this damaged bundle. The team was composed of key personnel from GPU Nuclear Fuels Projects, OCNGS Operations and Proto-Power / Bisco, a specialty contractor who has fuel bundle reconstitution and rod consolidation experience, remote tooling, underwater video systems and experienced technicians. Proven tooling, clear procedures and a simple approach were important, but the key element was the spirit of teamwork and leadership exhibited by the people involved

MONJU fuel pin performance analysis

International Nuclear Information System (INIS)

Kitagawa, H.; Yamanaka, T.; Hayashi, H.

1979-01-01

Monju fuel pin has almost the same properties as other LMFBR fuel pins, i.e. Phenix, PFR, CRBR, but would be irradiated under severe conditions: maximum linear heat rate of 381 watt/cm, hot spot cladding temperature of 675 deg C, peak burnup of 131,000 MWd/t, peak fluence (E greater than 0.1 MeV) of 2.3 10 23 n/cm 2 . In order to understand in-core performance of Monju fuel pin, its thermal and mechanical behaviour was predicted using the fast running performance code SIMPLE. The code takes into account pellet-cladding interaction due to thermal expansion and swelling, gap conductance, structural changes of fuel pellets, fission product gas release with burnup and temperature increase, swelling and creep of fuel pellets, corrosion of cladding due to sodium flow and chemical attack by fission products, and cumulative damage of the cladding due to thermal creep

Neutron radiography of fuel pins

International Nuclear Information System (INIS)

Jackson, C.N. Jr.; Powers, H.G.; Burgess, C.A.

1975-01-01

Neutron radiography performed with a reactor source has been shown to be a superior radiographic method for the examination of unirradiated mixed oxide fuel pins at the Hanford Engineering Development Laboratory. Approximately 1,700 fuel pins were contained in a sample that demonstrated the capability of the method for detecting laminations, structural flaws, fissile density variation, hydrogenous inclusions and voids in assembled fuel pins. The nature, extent, and importance of the detected conditions are substantiated by gamma autoradiography and by destructive analysis employing alpha autoradiography, electron microprobe and visual inspection. Also, a series of radiographs illustrate the response of neutron radiography as compared to low voltage and high voltage x-ray and gamma source Iridium 192 radiography. (U.S.)

Electro-optical fuel pin identification system

International Nuclear Information System (INIS)

Kirchner, T.L.

1978-09-01

A prototype Electro-Optical Fuel Pin Identification System referred to as the Fuel Pin Identification System (FPIS) has been developed by the Hanford Engineering Development Laboratory (HEDL) in support of the Fast Flux Test Facility (FFTF) presently under construction at HEDL. The system is designed to remotely read an alpha-numeric identification number that is roll stamped on the top of the fuel pin end cap. The prototype FPIS consists of four major subassemblies: optical read head, digital compression electronics, video display, and line printer

Ultrasonic inspections of fuel alignment pins

International Nuclear Information System (INIS)

Rathgeb, W.; Schmid, R.

1994-01-01

As a remedy to the practical problem of defects in fuel alignment pins made of Inconel X750, an inspection technique has been developed which fully meets the requirements of detecting defects. The newly used fuel alignment pins made of austenite are easy to test and therefore satisfy the necessity of further inspections.For the fuel alignment pins of the upper core structure a safe and fast inspection technique was made available. The inspection sensitivity is high and it is possible to give quantitative directions concerning defect orientation and depth. After the required inspections had been concluded in 1989, a total of 18 inspections were carried out in various national and international nuclear power plants in the following years. During this time more than 6000 fuel alignment pines were examined.For the fuel alignment pins the inspection technique provided could increase the understanding of the defect process. This technique contributed to the development of an adaptive and economical repair strategy. ((orig.))

Enthalpy and void distributions in subchannels of PHWR fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Park, J W; Choi, H; Rhee, B W [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1999-12-31

Two different types of the CANDU fuel bundles have been modeled for the ASSERT-IV code subchannel analysis. From calculated values of mixture enthalpy and void fraction distribution in the fuel bundles, it is found that net buoyancy effect is pronounced in the central region of the DUPIC fuel bundle when compared with the standard CANDU fuel bundle. It is also found that the central region of the DUPIC fuel bundle can be cooled more efficiently than that of the standard fuel bundle. From the calculated mixture enthalpy distribution at the exit of the fuel channel, it is found that the mixture enthalpy and void fraction can be highest in the peripheral region of the DUPIC fuel bundle. On the other hand, the enthalpy and the void fraction were found to be highest in the central region of the standard CANDU fuel bundle at the exit of the fuel channel. This study shows that the subchannel analysis is very useful in assessing thermal behavior of the fuel bundle that could be used in CANDU reactors. 10 refs., 4 figs., 2 tabs. (Author)

Enthalpy and void distributions in subchannels of PHWR fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Park, J. W.; Choi, H.; Rhee, B. W. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

Two different types of the CANDU fuel bundles have been modeled for the ASSERT-IV code subchannel analysis. From calculated values of mixture enthalpy and void fraction distribution in the fuel bundles, it is found that net buoyancy effect is pronounced in the central region of the DUPIC fuel bundle when compared with the standard CANDU fuel bundle. It is also found that the central region of the DUPIC fuel bundle can be cooled more efficiently than that of the standard fuel bundle. From the calculated mixture enthalpy distribution at the exit of the fuel channel, it is found that the mixture enthalpy and void fraction can be highest in the peripheral region of the DUPIC fuel bundle. On the other hand, the enthalpy and the void fraction were found to be highest in the central region of the standard CANDU fuel bundle at the exit of the fuel channel. This study shows that the subchannel analysis is very useful in assessing thermal behavior of the fuel bundle that could be used in CANDU reactors. 10 refs., 4 figs., 2 tabs. (Author)

Reusable fuel test assembly for the FFTF

International Nuclear Information System (INIS)

Pitner, A.L.; Dittmer, J.O.

1992-01-01

A fuel test assembly that provides re-irradiation capability after interim discharge and reconstitution of the test pin bundle has been developed for use in the Fast Flux Test Facility (FFTF). This test vehicle permits irradiation test data to be obtained at multiple exposures on a few select test pins without the substantial expense of fabricating individual test assemblies as would otherwise be required. A variety of test pin types can be loaded in the reusable test assembly. A reusable test vehicle for irradiation testing in the FFTF has long been desired, but a number of obstacles previously prevented the implementation of such an experimental rig. The MFF-8A test assembly employs a 169-pin bundle using HT-9 alloy for duct and cladding material. The standard driver pins in the fuel bundle are sodium-bonded metal fuel (U-10 wt% Zr). Thirty-seven positions in the bundle are replaceable pin positions. Standard MFF-8A driver pins can be loaded in any test pin location to fill the bundle if necessary. Application of the MFF-8A reusable test assembly in the FFTF constitutes a considerable cost-saving measure with regard to irradiation testing. Only a few well-characterized test pins need be fabricated to conduct a test program rather than constructing entire test assemblies

Development of CANDU advanced fuel bundle

International Nuclear Information System (INIS)

Suk, H. C.; Hwang, W.; Rhee, B. W.; Jung, S. H.; Chung, C. H.

1992-05-01

This research project is underway in cooperation with AECL to develop the CANDU advanced fuel bundle (so-called, CANFLEX) which can enhance reactor safety and fuel economy in comparison with the current CANDU fuel and which can be used with natural uranium, slightly enriched uranium and other advanced fuel cycle. As the final schedule, the advanced fuel will be verified by carrying out a large scale demonstration of the bundle irradiation in a commercial CANDU reactor for 1996 and 1997, and consequently will be used in the existing and future CANDU reactors in Korea. The research activities during this year include the detail design of CANFLEX fuel with natural enriched uranium (CANFLEX-NU). Based on this design, CANFLEX fuel was mocked up. Out-of-pile hydraulic scoping tests were conducted with the fuel in the CANDU Cold Test Loop to investigate the condition under which maximum pressure drop occurs and the maximum value of the bundle pressure drop. (Author)

Fuel pin bowing and related investigation of WWER-440 control rod influence on power release inside of neighbouring fuel pins

International Nuclear Information System (INIS)

Mikus, J.

2005-01-01

The purpose of this work consists in investigation of the WWER-440 control rod (CR) influence on space power distribution, especially from viewpoint of the values and gradient occurrence that could result in static and cyclic loads with some consequences, e.g. fuel pin bowing. As known, CR can cause power peaks in periphery fuel pins of adjacent operating assemblies because of the butt joint design of the absorbing adapter to the CR fuel part, that is, presence of the water cavity resulting in a flash up of thermal neutrons. As a consequence, beside well-known peaks in axial power distribution, above power gradients can occur inside of mentioned fuel pins. Because of complicated geometry and material composition of the CR, the detailed calculations concerning both above phenomena are complicated, too. Therefore it is useful to acquire appropriate experimental data to investigate mentioned influence and compare them with calculations. Since detailed power distributions cannot be obtained in the NPP, needed information is provided by means of experiments on research reactors. In case of measurements inside of fuel pins, special (e.g. track) detectors placed between fuel pellets are used. Such works are relatively complicated and time consuming, therefore an evaluation based on mathematical modelling and numerical approximation was proposed by means of that, and using measured power release in some selected fuel pins, information about power release inside of one of these fuel pins, can be obtained. For this purpose, an experiment on light water, zero-power research reactor LR-0 was realized and axial power distribution measurements were performed in a WWER-440 type core near to an authentic CR model. Application of the above evaluation method is demonstrated on one ''investigated'' fuel pin neighbouring CR by means of following results: 1. Axial power distribution inside of investigated fuel pin in two opposite positions on its pellets surface that are situated to

Development of CANFLEX fuel bundle

International Nuclear Information System (INIS)

Suk, Ho Chun; Hwang, Woan; Jeong, Young Hwan

1991-12-01

This research project is underway in cooperation with AECL to develop the CANDU advanced fuel bundle(so-called CANFLEX) which can enhance reactor safety and fuel economy in comparison with the current CANDU fuel and which can be used with natural uranium, slightly enriched uranium and other advanced fuel cycle. As the final schedule, the advanced fuel will be verified by carrying out a large scale demonstration of the bundle irradiation in a commercial CANDU reactors for 1996 and 1997, and consequently will be used in the existing and future reactors in Korea. The research activities during this year include the basic design of CANFLEX fuel with slightly enriched uranium(CANFLEX-SEU), with emphasis on the extension of fuel operation limit. Based on this basic design, CANFLEX fuel was mocked up. Out-of-pile hydraulic scoping tests were conducted with the fuel. (Author)

Postirradiation examinations of fuel pins from the GCFR F-1 series of mixed-oxide fuel pins at 5.5 at. % burnup

International Nuclear Information System (INIS)

Strain, R.V.; Johnson, C.E.

1978-05-01

Postirradiation examinations were performed on five fuel pins from the Gas-Cooled Fast-Breeder Reactor F-1 experiment irradiated in EBR-II to a peak burnup of approximately 5.5 at. %. These encapsulated fuel pins were irradiated at peak-power linear ratings from approximately 13 to 15 kW/ft and peak cladding inside diameter temperatures from approximately 625 to 760 0 C. The maximum diametral change that occurred during irradiation was 0.2% ΔD/D 0 . The maximum fuel-cladding chemical interaction depth was 2.6 mils in fuel pin G-1 and 1 mil or less in the other three pins examined destructively. Significant migration of the volatile fission products occurred axially to the fuel-blanket interfaces. Teh postirradiation examination data indicate that fuel melted at the inner surface of the annular fuel pellets in the two highest power rating fuel pins, but little axial movement of fuel occurred

Postirradiation examinations of fuel pins from the GCFR F-1 series of mixed-oxide fuel pins at 5. 5 at. % burnup

Energy Technology Data Exchange (ETDEWEB)

Strain, R V; Johnson, C E

1978-05-01

Postirradiation examinations were performed on five fuel pins from the Gas-Cooled Fast-Breeder Reactor F-1 experiment irradiated in EBR-II to a peak burnup of approximately 5.5 at. %. These encapsulated fuel pins were irradiated at peak-power linear ratings from approximately 13 to 15 kW/ft and peak cladding inside diameter temperatures from approximately 625 to 760/sup 0/C. The maximum diametral change that occurred during irradiation was 0.2% ..delta..D/D/sub 0/. The maximum fuel-cladding chemical interaction depth was 2.6 mils in fuel pin G-1 and 1 mil or less in the other three pins examined destructively. Significant migration of the volatile fission products occurred axially to the fuel-blanket interfaces. Teh postirradiation examination data indicate that fuel melted at the inner surface of the annular fuel pellets in the two highest power rating fuel pins, but little axial movement of fuel occurred.

Simulations and measurements of adiabatic annular flows in triangular, tight lattice nuclear fuel bundle model

Energy Technology Data Exchange (ETDEWEB)

Saxena, Abhishek, E-mail: asaxena@lke.mavt.ethz.ch [ETH Zurich, Laboratory for Nuclear Energy Systems, Department of Mechanical and Process Engineering, Sonneggstrasse 3, 8092 Zürich (Switzerland); Zboray, Robert [Laboratory for Thermal-hydraulics, Nuclear Energy and Safety Department, Paul Scherrer Institute, 5232 Villigen PSI (Switzerland); Prasser, Horst-Michael [ETH Zurich, Laboratory for Nuclear Energy Systems, Department of Mechanical and Process Engineering, Sonneggstrasse 3, 8092 Zürich (Switzerland); Laboratory for Thermal-hydraulics, Nuclear Energy and Safety Department, Paul Scherrer Institute, 5232 Villigen PSI (Switzerland)

2016-04-01

High conversion light water reactors (HCLWR) having triangular, tight-lattice fuels bundles could enable improved fuel utilization compared to present day LWRs. However, the efficient cooling of a tight lattice bundle has to be still proven. Major concern is the avoidance of high-quality boiling crisis (film dry-out) by the use of efficient functional spacers. For this reason, we have carried out experiments on adiabatic, air-water annular two-phase flows in a tight-lattice, triangular fuel bundle model using generic spacers. A high-spatial-resolution, non-intrusive measurement technology, cold neutron tomography, has been utilized to resolve the distribution of the liquid film thickness on the virtual fuel pin surfaces. Unsteady CFD simulations have also been performed to replicate and compare with the experiments using the commercial code STAR-CCM+. Large eddies have been resolved on the grid level to capture the dominant unsteady flow features expected to drive the liquid film thickness distribution downstream of a spacer while the subgrid scales have been modeled using the Wall Adapting Local Eddy (WALE) subgrid model. A Volume of Fluid (VOF) method, which directly tracks the interface and does away with closure relationship models for interfacial exchange terms, has also been employed. The present paper shows first comparison of the measurement with the simulation results.

Heat transfer in a fuel pin shipping container

International Nuclear Information System (INIS)

Ingham, J.G.

1980-01-01

Maximum cladding temperatures occur when the IDENT 1578 fuel pin shipping container is installed in the T-3 Cask. The maximum allowable cladding temperature of 800 0 F is reached when the rate of energy deposited in the 19-pin basket reaches 400 watts. Since 45% of the energy which is generated in the fuel escapes the 19-pin basket without being deposited, mostly gamma energy, the maximum allowable rate of heat generation is 400/.55 = 727 watts. Similarly, the maximum allowable cladding temperature of 800 0 F is reached when the rate of energy deposited in the 40-pin basket reaches 465 watts. Since 33% of the energy which is generated in the fuel escapes the 40-pin basket without being deposited, mostly gamma energy, the maximum allowable rate of heat generation is 465/.66 = 704 watts. The IDENT 1578 fuel pin shipping container therefore meets its thermal design criteria. IDENT 1578 can handle fuel pins with a decay heat load of 600 watts while maintaining the maximum fuel pin cladding temperature below 800 0 F. The emissivities which were determined from the test results for the basket tubes and container are relatively low and correspond to new, shiny conditions. As the IDENT 1578 container is exposed to high temperatures for extended periods of time during the transportation of fuel pins, the emissivities will probably increase. This will result in reduced temperatures

CANFLEX fuel bundle junction pressure drop

International Nuclear Information System (INIS)

Chung, H. J.; Chung, C. H.; Jun, J. S.; Hong, S. D.; Chang, S. K.; Kim, B. D.

1996-11-01

This report describes the junction pressure drop test results which are to used to determine the alignment angle between bundles to achieve the most probable fuel string pressure drop for randomly aligned bundles for use in the fuel string total pressure drop test. (author). 4 tabs., 17 figs

CANFLEX fuel bundle junction pressure drop

Energy Technology Data Exchange (ETDEWEB)

Chung, H. J.; Chung, C. H.; Jun, J. S.; Hong, S. D.; Chang, S. K.; Kim, B. D.

1996-11-01

This report describes the junction pressure drop test results which are to used to determine the alignment angle between bundles to achieve the most probable fuel string pressure drop for randomly aligned bundles for use in the fuel string total pressure drop test. (author). 4 tabs., 17 figs.

Experimental study on the effect of heat flux tilt on rod bundle dryout limitation

Energy Technology Data Exchange (ETDEWEB)

Sugawara, S; Terunuma, K; Kamoshida, H [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

1996-12-31

The effect of heat flux tilt on rod bundle dryout limitation was studied experimentally using a full-scale mock-up test facility and simulated 36-rod fuel bundles in which heater pins have azimuthal nonuniform heat flux distribution (i.e., heat flux tilt). Experimental results for typical lateral power distribution in the bundle indicate that the bundle dryout power with azimuthal heat flux tilt is higher than that without azimuthal heat flux tilt in the entire experimental range. Consequently, it is concluded that the dryout experiment using the test bundle with heater pins which has circumferentially uniform heat flux distribution gives conservative results for the usual lateral power distribution in a bundle in which the relative power of outermost-circle fuel rods is higher than those of middle- and inner-circle ones. (author). 15 refs., 2 tabs., 8 figs.

Experimental study on the effect of heat flux tilt on rod bundle dryout limitation

International Nuclear Information System (INIS)

Sugawara, S.; Terunuma, K.; Kamoshida, H.

1995-01-01

The effect of heat flux tilt on rod bundle dryout limitation was studied experimentally using a full-scale mock-up test facility and simulated 36-rod fuel bundles in which heater pins have azimuthal nonuniform heat flux distribution (i.e., heat flux tilt). Experimental results for typical lateral power distribution in the bundle indicate that the bundle dryout power with azimuthal heat flux tilt is higher than that without azimuthal heat flux tilt in the entire experimental range. Consequently, it is concluded that the dryout experiment using the test bundle with heater pins which has circumferentially uniform heat flux distribution gives conservative results for the usual lateral power distribution in a bundle in which the relative power of outermost-circle fuel rods is higher than those of middle- and inner-circle ones. (author). 15 refs., 2 tabs., 8 figs

Performance of candu-6 fuel bundles manufactured in romania nuclear fuel plant

International Nuclear Information System (INIS)

Bailescu, A.; Barbu, A.; Din, F.; Dinuta, G.; Dumitru, I.; Musetoiu, A.; Serban, G.; Tomescu, A.

2013-01-01

The purpose of this article is to present the performance of nuclear fuel produced by Nuclear Fuel Plant (N.F.P.) - Pitesti during 1995 - 2012 and irradiated in units U1 and U2 from Nuclear Power Plant (N.P.P.) Cernavoda and also present the Nuclear Fuel Plant (N.F.P.) - Pitesti concern for providing technology to prevent the failure causes of fuel bundles in the reactor. This article presents Nuclear Fuel Plant (N.F.P.) - Pitesti experience on tracking performance of nuclear fuel in reactor and strategy investigation of fuel bundles notified as suspicious and / or defectives both as fuel element and fuel bundle, it analyzes the possible defects that can occur at fuel bundle or fuel element and can lead to their failure in the reactor. Implementation of modern technologies has enabled optimization of manufacturing processes and hence better quality stability of achieving components (end caps, chamfered sheath), better verification of end cap - sheath welding. These technologies were qualified by Nuclear Fuel Plant (N.F.P.) - Pitesti on automatic and Computer Numerical Control (C.N.C.) programming machines. A post-irradiation conclusive analysis which will take place later this year (2013) in Institute for Nuclear Research Pitesti (the action was initiated earlier this year by bringing a fuel bundle which has been reported defective by pool visual inspection) will provide additional information concerning potential damage causes of fuel bundles due to manufacturing processes. (authors)

Integral Fast Reactor fuel pin processor

International Nuclear Information System (INIS)

Levinskas, D.

1993-01-01

This report discusses the pin processor which receives metal alloy pins cast from recycled Integral Fast Reactor (IFR) fuel and prepares them for assembly into new IFR fuel elements. Either full length as-cast or precut pins are fed to the machine from a magazine, cut if necessary, and measured for length, weight, diameter and deviation from straightness. Accepted pins are loaded into cladding jackets located in a magazine, while rejects and cutting scraps are separated into trays. The magazines, trays, and the individual modules that perform the different machine functions are assembled and removed using remote manipulators and master-slaves

Correlation of creep and swelling with fuel pin performance

International Nuclear Information System (INIS)

Jackson, R.J.; Washburn, D.F.; Garner, F.A.; Gilbert, E.R.

1975-09-01

The HEDL PNL-11 experiment described was one in a series of fueled subassemblies irradiated in EBR-II to demonstrate the adequacy of the FFTF fuel pin design. The cladding material, dimensions, and fuel density are prototypic of FFTF. Because neutron flux in EBR-II is lower than in FFTF, the uranium enrichment is higher in these experimental fuel pins, irradiated in EBR-II, than the FFTF enrichment for comparable linear heat rates. Some pertinent oprating conditions for the center fuel pin in this experiment are listed. This 37-pin subassembly represents, at 110,000 MWd/MTM, the highest burnup yet attained by a prototypic FFTF subassembly. Similarly, this is the highest fluence presently attained by prototypic fuel pins. A cladding breach occurred in one fuel pin which is presently being examined. Results are presented and discussed

Nuclear fuel bundle disassembly and assembly tool

International Nuclear Information System (INIS)

Yates, J.; Long, J.W.

1975-01-01

A nuclear power reactor fuel bundle is described which has a plurality of tubular fuel rods disposed in parallel array between two transverse tie plates. It is secured against disassembly by one or more locking forks which engage slots in tie rods which position the transverse plates. Springs mounted on the fuel and tie rods are compressed when the bundle is assembled thereby maintaining a continual pressure against the locking forks. Force applied in opposition to the springs permits withdrawal of the locking forks so that one tie plate may be removed, giving access to the fuel rods. An assembly and disassembly tool facilitates removal of the locking forks when the bundle is to be disassembled and the placing of the forks during assembly of the bundle. (U.S.)

Fabrication of FFTF fuel pin wire wrap

International Nuclear Information System (INIS)

Epperson, E.M.

1980-06-01

Lateral spacing between FFTF fuel pins is required to provide a passageway for the sodium coolant to flow over each pin to remove heat generated by the fission process. This spacing is provided by wrapping each fuel pin with type 316 stainless steel wire. This wire has a 1.435mm (0.0565 in.) to 1.448mm (0.0570 in.) diameter, contains 17 +- 2% cold work and was fabricated and tested to exacting RDT Standards. About 500 kg (1100 lbs) or 39 Km (24 miles) of fuel pin wrap wire is used in each core loading. Fabrication procedures and quality assurance tests are described

Stress relaxation of thermally bowed fuel pins

International Nuclear Information System (INIS)

Crossland, I.G.; Speight, M.V.

1983-01-01

The presence of cross-pin temperature gradients in nuclear reactor fuel pins produces differential thermal expansion which, in turn, causes the fuel pin to bow elastically. If the pin is restrained in any way, such thermal bowing causes the pin to be stressed. At high temperatures these stresses can relax by creep and it is shown here that this causes the pin to suffer an additional permanent deflection, so that when the cross-pin temperature difference is removed the pin remains bowed. By representing the cylindrical pin by an equivalent I-beam, the present work examines this effect when it takes place by secondary creep. Two restraint systems are considered, and it is demonstrated that the rate of relaxation depends mainly upon the creep equation, and hence the temperature, and also the magnitude of the initial stresses. (author)

In-pool damaged fuel bundle recovery

International Nuclear Information System (INIS)

Piascik, T.G.; Patenaude, R.S.

1988-01-01

While preparing to rerack the Oyster Creek Nuclear Generating Station, GPU Nuclear had need to move a damaged fuel bundle. This bundle had no upper tie plate and could not be moved in the normal manner. GPU Nuclear formed a small, dedicated project team to disassemble, package, and move this damaged bundle. The team was composed of key personnel from GPU Nuclear Fuels Projects, OCNGS Operations and Proto-Power/Bisco, a specialty contractor who has fuel bundle reconstitution and rod consolidation experience, remote tooling, underwater video systems and experienced technicians. Proven tooling, clear procedures and a simple approach were important, but the key element was the spirit of teamwork and leadership exhibited by the people involved. In spite of several emergent problems which a task of this nature presents, this small, close knit utility/vendor team completed the work on schedule and within the exposure and cost budgets

FFTF/IEM cell fuel pin weighing system

International Nuclear Information System (INIS)

Gibbons, P.W.

1987-01-01

The Interim Examination and Maintenance (IEM) cell in the Fast Flux Test Facility (FFTF) is used for remote disassembly of irradiated fuel and materials experiments. For those fuel experiments where the FFTF tag-gas detection system has indicated a fuel pin cladding breach, a weighing system is used in identifying that fuel pin with a reduced weight due to the escape of gaseous and volatile fission products. A fuel pin weighing machine, originally purchased for use in the Fuels and Materials Examination Facility (FMEF), was the basis for the IEM cell system. Design modifications to the original equipment were centered around adapting the machine to the differences between the two facilities and correcting deficiencies discovered during functional testing in the IEM cell mock-up

CFD thermal-hydraulic analysis of a CANDU fuel channel with SEU43 type fuel bundle

International Nuclear Information System (INIS)

Catana, A.; Prisecaru, Ilie; Dupleac, D.; Danila, Nicolae

2009-01-01

This paper presents the numerical investigation of a CANDU fuel channel using CFD (Computational Fluid Dynamics) methodology approach, when SEU43 fuel bundles are used. Comparisons with STD37 fuel bundles are done in order to evaluate the influence of geometrical differences of the fuel bundle types on fluid flow properties. We adopted a strategy to analyze only the significant segments of fuel channel, namely : - the fuel bundle junctions with adjacent segments; - the fuel bundle spacer planes with adjacent segments; - the fuel bundle segments with turbulence enhancement buttons; - and the regular segments of fuel bundles. The computer code used is an academic version of FLUENT code, available from UPB. The complex flow domain of fuel bundles contained in pressure tube and operating conditions determine a high turbulence flow and in some parts of fuel channel also a multi-phase flow. Numerical simulation of the flow in the fuel channel has been achieved by solving the equations for conservation of mass, momentum and energy. For turbulence model the standard k-model is employed although other turbulence models can be used. In this paper we do not consider heat generation and heat transfer capabilities of CFD methods. Boundary conditions for CFD analysis are provided by system and sub-channel analysis. In this paper the discussion is focused on some flow parameters behaviour at the bundle junction, spacer's plane configuration, etc. of a SEU43 fuel bundle in conditions of a typical CANDU 6 fuel channel starting from some experience gained in a previous work. (authors)

CANDU fuel bundle deformation modelling with COMSOL multiphysics

International Nuclear Information System (INIS)

Bell, J.S.; Lewis, B.J.

2012-01-01

Highlights: ► The deformation behaviour of a CANDU fuel bundle was modelled. ► The model has been developed on a commercial finite-element platform. ► Pellet/sheath interaction and end-plate restraint effects were considered. ► The model was benchmarked against the BOW code and a variable-load experiment. - Abstract: A model to describe deformation behaviour of a CANDU 37-element bundle has been developed under the COMSOL Multiphysics finite-element platform. Beam elements were applied to the fuel elements (composed of fuel sheaths and pellets) and endplates in order to calculate the bowing behaviour of the fuel elements. This model is important to help assess bundle-deformation phenomena, which may lead to more restrictive coolant flow through the sub-channels of the horizontally oriented bundle. The bundle model was compared to the BOW code for the occurrence of a dry-out patch, and benchmarked against an out-reactor experiment with a variable load on an outer fuel element.

Analysis of fuel cladding chemical interaction in mixed oxide fuel pins

International Nuclear Information System (INIS)

Weber, J.W.; Dutt, D.S.

1976-01-01

An analysis is presented of the observed interaction between mixed oxide 75 wt percent UO 2 --25 wt percent PuO 2 fuel and 316--20 percent CW stainless steel cladding in LMFBR type fuel pins irradiated in EBR-II. A description is given of the test pins and their operating conditions together with, metallographic observations and measurements of the fuel/cladding reaction, and a correlation equation is developed relating depth of cladding attack to temperature and burnup. Some recent data on cladding reaction in fuel pins with low initial O/M in the fuel are given and compared with the correlation equation curves

Delayed Fission Product Gamma-Ray Transmission Through Low Enriched UO₂ Fuel Pin Lattices in Air

Energy Technology Data Exchange (ETDEWEB)

Trumbull, TH [Rensselaer Polytechnic Inst., Troy, NY (United States)

2004-10-18

The transmission of delayed fission-product gamma rays through various arrangements of low-enriched UO2 fuel pin lattices in an air medium was studied. Experimental measurements, point-kernel and Monte Carlo photon transport calculations were performed to demonstrate the shielding effect of ordered lattices of fuel pins on the resulting gamma-ray dose to a detector outside the lattice. The variation of the gamma-ray dose on the outside of the lattice as a function of radial position, the so-called “channeling” effect, was analyzed. Techniques for performing experimental measurements and data reduction at Rensselaer Polytechnic Institute’s Reactor Critical Facility (RCF) were derived. An experimental apparatus was constructed to hold the arrangements of fuel pins for the measurements. A gamma-ray spectroscopy system consisting of a sodium-iodide scintillation detector was used to collect data. Measurements were made with and without a collimator installed. A point-kernel transport code was developed to map the radial dependence of the gamma-ray flux. Input files for the Monte Carlo code, MCNP, were also developed to accurately model the experimental measurements. The results of the calculations were compared to the experimental measurements. In order to determine the delayed fission-product gamma-ray source for the calculations, a technique was developed using a previously written code, DELBG and the reactor state-point data obtained during the experimental measurements. Calculations were performed demonstrating the effects of material homogenization on the gamma-ray transmission through the fuel pin lattice.Homogeneous and heterogeneous calculations were performed for all RCF fuel pin lattices as well as for a typical commercial pressurized water reactor fuel bundle. The results of the study demonstrated the effectiveness of the experimental measurements to isolate the channeling effect of delayed fission-product gamma-rays through lattices of RCF fuel pins

Fuel Coolant Interaction Results in the Fuel Pins Melting Facility (PMF)

International Nuclear Information System (INIS)

Urunashi, H.; Hirabayashi, T.; Mizuta, H.

1976-01-01

The experimental work related to FCI at PNC has been concentrated into the molten UO 2 dropping test. After the completion of molten UO 2 drop experiments, emphasis is directed toward the FCI phenomena of the initiating conditions of the accident under the more realistic geometry. The experiments are conducted within the Pin Melt Facility (PMF) in which UO 2 pellets clad in stainless steel are melted by direct electric heating under the stagnant or flowing sodium. The primary objectives of the PMF test are to: - obtain detail experimental results (heat-input, clad temperature, sodium temperature, etc.) on the FCI under TOP and LOF conditions; - observe the movement of the fuel before and after the pin failure by the X-ray cinematography; - observe the degree of coherence of the pin failures; - accumulate the experience of the FCI experiment which is applicable to the subassembly or more larger scale; - simulate the fuel behavior of the in-pile test (GETR, CABRI). The preliminary conclusions can be drawn from the foregoing observations are as follows: - Although the fuel motion and FCI of the closed test section appeared to be different from those of the open test section, the conclusion of the effect of the inside pressure on FCI needs more experimental data. - The best heating condition of the UO 2 pellet for the FCI study with PMF is established as 40 w/cm at the steady state and 1680 J/g of UO 2 during the additional transient state. The total energy deposition of the UO 2 pellet is thus estimated in the range of 2400 J/g of UO 2 -2600 J/g of UO 2 . The analytical model of the fuel pin failure and the subsequent FCI are suggested to count the following parameters: - The fuel pin failure due to the fuel vaporization due to the rapid energy deposition; - Molten fuel, clad and sodium interaction in the fuel pin after the pin failure; - The upward flow of molten fuel with molten clad or vapor sodium, as well as the slumping of molten fuel

Comparative prediction of irradiation test of CNFT and Cise prototypes of CIRENE fuel pins, a prediction by transuranus M1V1J12 code

International Nuclear Information System (INIS)

Suwardi

2014-01-01

A prototype of fuel pin design for HWR by CIRENE has been realized by Center for Nuclear Fuel Technology CNFT-BATAN. The prototype will be irradiated in PRTF Power Ramp Test (PRTF). The facility has been installed inside RSG-GA Siwabessy at Serpong. The present paper reports the preparation of experimentation and prediction of irradiation test. One previous PCI test report is found in, written by Lysell G and Valli G in 1973. The CNFT fuel irradiation test parameter is adapted to both PRTF and power loop design for RSG-GAS reactor in Serpong mainly the maxima of: rod length, neutrons flux, total power of rod, and power ramp rate. The CNFT CIRENE prototype design has been reported by Futichah et al 2007 and 2010. The AEC-India HWR fuel pin is of 19/22 fuel bundle design has also been evaluated as comparison. The first PCI test prediction has experiment comparison for Cise pin. The second prediction will be used for optimizing the design of ramp test for CNFT CIRENE fuel pin prototype. (author)

Characterization of velocity and temperature fields in a 217 pin wire wrapped fuel bundle of sodium cooled fast reactor

International Nuclear Information System (INIS)

Naveen Raj, M.; Velusamy, K.

2016-01-01

Highlights: • We simulate flow and temperature fields in fuel subassembly of fast reactor. • We perform high fidelity computations for 217 pin bundle of 7 axial pitch lengths. • We investigate transverse and axial flows in different types of subchannels. • Correlations are proposed for transverse flow, which form input for subchannel analysis. • Periodic variations of large magnitude are observed in subchannel flow rates. - Abstract: RANS based computational fluid dynamic (CFD) simulation of flow and temperature fields in a fast reactor fuel subassembly has been carried out. The sodium cooled prototype subassembly consists of 217 pins with helical wire spacers. An axial length of seven helical wire pitches has been considered for the study adopting a structured mesh having 36 million points and 84 processors in parallel. The computational model has been validated against in-house and published experimental data for friction factor and Nusselt number. Also, the transverse flow in the central subchannel and swirl flow in the peripheral subchannel are compared against reported experimental data and those computed by subchannel models. The focus of the study is investigation of transverse and axial flows in different types of subchannels. Based on the 3-dimensional CFD study, correlations have been proposed for calculation of transverse flow, which forms an important input for development of subchannel analysis codes. Periodic variations have been observed in the subchannel axial flow rates. For the subchannels located in the central region, the peak to peak variation in the axial flow rate is ∼21% and it is found to be contributed by the changes in the flow area and hydraulic resistance due to frequent passage of helical wires through the subchannel. For the subchannels located in the periphery, this variation is as high as 50%. The transverse flow in the central subchannels follows a cosine profile, for all the faces. However, there is a phase lag of 120�

Post irradiation examination on test fuel pins for PWR

International Nuclear Information System (INIS)

Fogaca Filho, N.; Ambrozio Filho, F.

1981-01-01

Certain aspects of irradiation technology on test fuel pins for PWR, are studied. The results of post irradiation tests, performed on test fuel pins in hot cells, are presented. The results of the tests permit an evaluation of the effects of irradiation on the fuel and cladding of the pin. (Author) [pt

Irradiation experience with KNK II Fast Breeder Fuel Subassemblies

International Nuclear Information System (INIS)

Hess, B.

1993-02-01

During the operation of the second core of KNK II fuel pin failures occurred, which were caused by local cladding weakening due to mechanical interaction between fuel pins and pin spacers. The present report gives a summarizing presentation of the consequences of these interactions, of the experimental and theoretical investigations to clarify the reason for the interactions and of measures to reduce their consequences in the extended residence time of the second core of KNK II. This type of interaction is caused by thermo-elastic instabilities of the fuel pin bundle, and its strength depends sensitively on the geometry of the pin bundle and the pin power. Finally, measures are described, which were taken for the fuel subassemblies of the third core of KNK II to avoid the wear causing instabilities [de

Improved Retrieval Technique of pin-wise composition for spent fuel recycling

Energy Technology Data Exchange (ETDEWEB)

Park, YunSeo; Kim, Myung Hyun [Kyung Hee University , Yongin (Korea, Republic of)

2016-10-15

New reutilization method which does not require fabrication processing was suggested and showed feasibility by Dr. Aung Tharn Daing. This new reutilization method is predict spent nuclear fuel pin composition, reconstruct new fuel assembly by spent nuclear pin, and directly reutilize in same PWR core. There are some limitation to predict spent nuclear fuel pin composition on his methodology such as spatial effect was not considered enough. This research suggests improving Dr. Aung Tharn Daing's retrieval technique of pin-wise composition. This new method classify fuel pin groups by its location effect in fuel assembly. Most of fuel pin composition along to burnup in fuel assembly is not highly dependent on location. However, compositions of few fuel pins where near water hole and corner of fuel assembly are quite different in same burnup. Required number of nuclide table is slightly increased from 3 to 6 for one fuel assembly with this new method. Despite of this little change, prediction of the pin-wise composition became more accurate. This new method guarantees two advantages than previous retrieving technique. First, accurate pin-wise isotope prediction is possible by considering location effect in a fuel assembly. Second, it requires much less nuclide tables than using full single assembly database. Retrieving technique of pin-wise composition can be applied on spent fuel management field useful. This technique can be used on direct use of spent fuel such as Dr. Aung Tharn Daing showed or applied on pin-wise waste management instead of conventional assembly-wise waste management.

The interpretation of fuel centre temperature measurements on a suspected leaking fuel pin

International Nuclear Information System (INIS)

Ainscough, J.B.; Lang, C.; Clough, D.J.

1983-01-01

In order to study fuel densification a series of single instrumented pin irradiations has been carried out in the High Pressure Water Loop of DIDO at Harwell. The behaviour of two of these pins was different from that expected. In the fifth test, where the fuel was 95% dense pellet UO 2 and expected to densify readily in-reactor, the fuel centre temperature increased from its starting value of approx. 1300 deg. C at a rate somewhat higher than expected on the basis of predicted densification rates. After about six days, the temperature increased rapidly and unexpectedly to 2100-2200 deg. C and remained steady at this level for a further eight days until a reactor trip occurred and the pin was unloaded. Predictions made using the HOTROD code imply a maximum fuel temperature of less than 1500 deg. C after densification. Post-irradiation examination confirmed that fission gas release had occurred, that the measured temperatures were consistent with the fuel microstructure and that the pin had a high internal gas pressure. The fourth pin in the series contained 97% dense UO 2 which was also expected to be dimensionally unstable. Qualitatively its behaviour was similar to that of the fifth pin though the temperatures throughout were lower. This pin experienced a number of major power cycles and failed after about 30 days in-reactor. It is probable that coolant ingress occurred in both pins via the thermocouple Hoke seal, degrading the filling gas conductivity and allowing the fuel to densify rapidly with consequent increase in the fuel/clad gap and hence in fuel temperature. These irradiations show that, for a short time at least, an apparently unfailed pin could operate undetected with temperatures significantly higher than those predicted for normal operation. (author)

A device for supporting a pin bundle in a nuclear reactor assembly casing

International Nuclear Information System (INIS)

Marmonier, Pierre; Mesnage, Bernard; Teulon, Jean; Vayra, Jean; Venobre, Henri.

1974-01-01

Description is given of a device for supporting a pin-bundle in a nuclear reactor assembly casing. That device comprises a member coaxially mounted at the bottom of the vertically mounted casing, adapted to support a plurality of parallel rails along whose edges slide grooves made in the pin-plugs. It is characterized in that said supporting member is provided with a lateral groove open toward its periphery, cooperating with clamping-lugs that form extensions of the rail-sides and comprise an inwardly directed portion adapted to be engaged in the groove. This can be applied to fast neutron nuclear reactors [fr

Implications and control of fuel-cladding chemical interaction for LMFBR fuel pin design

International Nuclear Information System (INIS)

Roake, W.E.

1977-01-01

Fuel-cladding-chemical-interaction (FCCI) is typically incorporated into the design of an LMFBR fuel pin as a wastage allowance. Several interrelated factors are considered during the evolution of an LMFBR fuel pin design. Those which are indirectly affected by FCCI include: allowable pin power, fuel restructuring, fission gas migration and release from the fuel, fuel cracking, fuel swelling, in-reactor cladding creep, cladding swelling, and the cladding mechanical strain. Chemical activity of oxygen is the most readily controlled factor in FCCI. Two methods are being investigated: control of total oxygen inventory by limiting fuel O/M, and control of oxygen activity with buffer metals

Implications and control of fuel-cladding chemical interaction for LMFBR fuel pin design

Energy Technology Data Exchange (ETDEWEB)

Roake, W E [Westinghouse-Hanford Co., Richland, WA (United States)

1977-04-01

Fuel-cladding-chemical-interaction (FCCI) is typically incorporated into the design of an LMFBR fuel pin as a wastage allowance. Several interrelated factors are considered during the evolution of an LMFBR fuel pin design. Those which are indirectly affected by FCCI include: allowable pin power, fuel restructuring, fission gas migration and release from the fuel, fuel cracking, fuel swelling, in-reactor cladding creep, cladding swelling, and the cladding mechanical strain. Chemical activity of oxygen is the most readily controlled factor in FCCI. Two methods are being investigated: control of total oxygen inventory by limiting fuel O/M, and control of oxygen activity with buffer metals.

Progress in fuel pin modelling in the USA

Energy Technology Data Exchange (ETDEWEB)

Stephen, J D; Biancheria, A; Leibnitz, D; O' Reilly, B D; Liu, Y Y; Labar, M P; Gneiting, B C [General Electric Company, Sunnyvale, CA (United States)

1979-12-01

In the USA, the focus for theoretical fuel pin modeling is the LIFE system. This system of codes, algorithms, criteria and analysis guidelines is intended to provide a common basis for communication amongst the development groups, a reference set of analysis guidelines for design, and eventually a consensus on the state-of-the-art for licensing. The technical objective is to predict the effect of design options on fuel pin performance limits, which include fuel temperature, pin deformation and cladding breach during normal operation and design basis transients. The mechanistic approach to modeling is taken in LIFE to the extent possible. That is, the approach is to describe the key phenomena in sufficient detail to provide a fundamental understanding of their synergistic effect on the fuel pin performance limits.

SP-100 Fuel Pin Performance: Results from Irradiation Testing

Science.gov (United States)

Makenas, Bruce J.; Paxton, Dean M.; Vaidyanathan, Swaminathan; Marietta, Martin; Hoth, Carl W.

1994-07-01

A total of 86 experimental fuel pins with various fuel, liner, and cladding candidate materials have been irradiated in the Experimental Breeder Reactor-II (EBR-II) and the Fast Flux Test Facility (FFTF) reactor as part of the SP-100 fuel pin irradiation testing program. Postirradiation examination results from these fuel pins are key in establishing performance correlations and demonstrating the lifetime and safety of the reactor fuel system. This paper provides a brief description of the in-reactor fuel pin tests and presents the most recent irradiation data on the performance of wrought rhenium (Re) liner material and high density UN fuel at goal burnup of 6 atom percent (at. %). It also provides an overview of the significant variety of other fuel/liner/cladding combinations which were irradiated as part of this program and which may be of interest to more advanced efforts.

Correlations between fuel pins irradiated in fast and thermal fluxes using the frump fuel pin modelling program

International Nuclear Information System (INIS)

Hayns, M.R.; Adam, J.

1975-08-01

There is no experimental facilities in which a fuel pin can be irradiated in a fast environment under well defined conditions of over power or flow run down. Consequently most of the infor mation which is being accumulated on the behaviour of fuel pins under severe conditions is obtained from either capsule or loop rigs in thermal reactors. It is the purpose of this paper to highlight the differences between the behaviour of fuel pins irradiated in a thermal flux and a fast flux. A typical set of conditions is taken from an overpower experiment in a thermal flux and the behaviour of the system is analysed using the fuel modelling program FRUMP. A second numerical experiment is then performed in which the same conditions prevail, except that a fast flux is assumed, the criterion for comparison being that the total power input to the system is the same in both cases. From the many possible correlations which result from such an exercise the fuel tempreature has been selected to highlight various important features of the two irradiations. It is demonstrated that the flux depression can cause differences in the pin behaviour, even to altering the order of events in a transient. For example fuel melting will occur at different times and at different positions in the fuel in the two cases. It is concluded that the techniques of fuel modelling, as typified in the program FRUMP can provide a very useful tool indeed for the analysis of such experiments and for guiding the establishment of the appropriate correlations for the extrapolation to the fast flux case. (author)

Experimental confirmation of the design to minimize vibration and wear in 61-pin wire-spaced EBR-II subassemblies

International Nuclear Information System (INIS)

Fukuda, S.K.

1978-05-01

Examinations of HEDL 61-pin subassemblies comprised of 5.84 mm (0.230) inch diameter mixed-oxide fuel pins with 1.02 mm (0.040'') diameter spacer wire (PNL-9, -10, -11, HEDL-N-E, -N-F), showed severe cladding and spacer wire wear after irradiation in EBR-II. A comparison of a large number of design, fabrication, and irradiation parameters for all of the HEDL subassemblies indicated that the porosity per ring of fuel pins correlated significantly with the occurrence of wear on the fuel pins. The porosity per ring is the clearance between the flat-to-flat pin bundle dimension and the inner hex can dimension divided by the number of hexagonal fuel pin rings in the subassembly. The porosity per ring for PNL-9, -10, -11 and HEDL-N-E was 0.15 mm/ring (6 mils/ring) and 0.18 mm/ring (7 mils/ring) for the HEDL-N-F subassembly. Since the original FTR subassembly design had a porosity/ring spread of 0.04 mm/ring to 0.16 mm/ring (1.67 to 6.11 mils/ring) an additional series of irradiation tests was conducted to confirm that a tighter fuel pin bundle would eliminate the wear

Whole-Pin Furnace system: An experimental facility for studying irradiated fuel pin behavior under potential reactor accident conditions

International Nuclear Information System (INIS)

Liu, Y.Y.; Tsai, H.C.; Donahue, D.A.; Pushis, D.O.; Savoie, F.E.; Holland, J.W.; Wright, A.E.; August, C.; Bailey, J.L.; Patterson, D.R.

1990-05-01

The whole-pin furnace system is a new in-cell experimental facility constructed to investigate how irradiated fuel pins may fail under potential reactor accident conditions. Extensive checkouts have demonstrated excellent performance in remote operation, temperature control, pin breach detection, and fission gas handling. The system is currently being used in testing of EBIR-II-irradiated Integral Fast Reactor (IFR) metal fuel pins; future testing will include EBR-II-irradiated mixed-oxide fuel pins. 7 refs., 4 figs

CANFLEX fuel bundle strength tests (test report)

International Nuclear Information System (INIS)

Chang, Seok Kyu; Chung, C. H.; Kim, B. D.

1997-08-01

This document outlines the test results for the strength tests of the CANFLEX fuel bundle. Strength tests are performed to determine and verify the amount of the bundle shape distortion which is against the side-stops when the bundles are refuelling. There are two cases of strength test; one is the double side-stop test which simulates the normal bundle refuelling and the other is the single side-stop test which simulates the abnormal refuelling. the strength test specification requires that the fuel bundle against the side-stop(s) simulators for this test were fabricated and the flow rates were controlled to provide the required conservative hydraulic forces. The test rig conditions of 120 deg C, 11.2 MPa were retained for 15 minutes after the flow rate was controlled during the test in two cases, respectively. The bundle loading angles of number 13- number 15 among the 15 bundles were 67.5 deg CCW and others were loaded randomly. After the tests, the bundle shapes against the side-stops were measured and inspected carefully. The important test procedures and measurements were discussed as follows. (author). 5 refs., 22 tabs., 5 figs

Discharge Burnup Evaluation of Natural Uranium Loaded CANFLEX-43 Fuel Bundle

International Nuclear Information System (INIS)

Roh, Gyu Hong; Kim, Yong Hee; Kim, Won Young; Park, Joo Hwan

2009-11-01

Using WIMS-AECL code, which is 2-dimensional lattice core used in CANDU physics calculation, the discharge burnup of the natural uranium loaded CANFLEX-43 fuel bundle was evaluated by comparing the discharge burnup of standard 37 element fuel bundle. When the discharge burnup of the standard 37 element fuel is 7,200 MWd/MTU, that of the CANFLEX 43 fuel bundle was evaluated as 7,077 MWd/MTU, by applying the same lattice conditions for both fuel bundles

Fuel canister and blockage pin fabrication for SLSF Experiment P4

International Nuclear Information System (INIS)

Rhude, H.V.; Folkrod, J.R.; Noland, R.A.; Schaus, P.S.; Benecke, M.W.; Delucchi, T.A.

1983-01-01

As part of its fast breeder reactor safety research program, Argonne National Laboratory (ANL) has conducted an experiment (SLSF Experiment P4) to determine the extent of fuel-failure propagation resulting from the release of molten fuel from one or more heat-generating fuel canisters. The test conditions consisted of 37 full-length FTR fuel pins operating at FTR rated core nominal peak fuel/reduced coolant conditions. Thirty-four of the the fuel pins were prototypical FTR mixed-oxide fuel pins. The other three fuel pins were fabricated with a mid-core section having an enlarged canister containing fully enriched UO 2 . Two of the canisters were cylindrical and one was fluted. The cylindrical canisters were designed to fail and release molten fuel into the 37-pin fuel cluster at near full power

Investigations of fuel cladding chemical interaction in irradiated LMFBR type oxide fuel pins

International Nuclear Information System (INIS)

Roake, W.E.; Adamson, M.G.; Hilbert, R.F.; Langer, S.

1977-01-01

Understanding and controlling the chemical attack of fuel pin cladding by fuel and fission products are major objectives of the U.S. LMFBR Mixed Oxide Irradiation Testing Program. Fuel-cladding chemical interaction (FCCI) has been recognized as an important factor in the ability to achieve goal peak burnups of 8% (80.MWd/kg) in FFTF and in excess of 10% (100.MWd/kg) in the LMFBR demonstration reactors while maintaining coolant bulk outlet temperatures up to ∼60 deg. C (1100 deg. F). In this paper we review pertinent parts of the irradiation program and describe recent observation of FCCI in the fuel pins of this program. One goal of the FCCI investigations is to obtain a sufficiently quantitative understanding of FCCI such that correlations can be developed relating loss of effective cladding thickness to irradiation and fuel pin fabrication parameters. Wastage correlations being developed using different approaches are discussed. Much of the early data on FCCI obtained in the U.S. Mixed Oxide Fuel Program came from capsule tests irradiated in both fast and thermal flux facilities. The fast flux irradiated encapsulated fuel pins continue to provide valuable data and insight into FCCI. Currently, however, bare pins with prototypic fuels and cladding irradiated in the fast flux Experimental Breeder Reactor-II (EBR-II) as multiple pin assemblies under prototypic powers, temperatures and thermal gradients are providing growing quantities of data on FCCI characteristics and cladding thickness losses from FCCI. A few special encapsulated fuel pin tests are being conducted in the General Electric Test Reactor (GETR) and EBR-II, but these are aimed at providing specific information under irradiation conditions not achievable in the fast flux bare pin assemblies or because EBR-II Operation or Safety requirements dictate that the pins be encapsulated. The discussion in this paper is limited to fast flux irradiation test results from encapsulated pins and multiple pin

Investigations of fuel cladding chemical interaction in irradiated LMFBR type oxide fuel pins

Energy Technology Data Exchange (ETDEWEB)

Roake, W E [Westinghouse-Hanford Co., Richland, WA (United States); Adamson, M G [General Electric Company, Vallecitos Nuclear Center, Pleasanton, CA (United States); Hilbert, R F; Langer, S

1977-04-01

Understanding and controlling the chemical attack of fuel pin cladding by fuel and fission products are major objectives of the U.S. LMFBR Mixed Oxide Irradiation Testing Program. Fuel-cladding chemical interaction (FCCI) has been recognized as an important factor in the ability to achieve goal peak burnups of 8% (80.MWd/kg) in FFTF and in excess of 10% (100.MWd/kg) in the LMFBR demonstration reactors while maintaining coolant bulk outlet temperatures up to {approx}60 deg. C (1100 deg. F). In this paper we review pertinent parts of the irradiation program and describe recent observation of FCCI in the fuel pins of this program. One goal of the FCCI investigations is to obtain a sufficiently quantitative understanding of FCCI such that correlations can be developed relating loss of effective cladding thickness to irradiation and fuel pin fabrication parameters. Wastage correlations being developed using different approaches are discussed. Much of the early data on FCCI obtained in the U.S. Mixed Oxide Fuel Program came from capsule tests irradiated in both fast and thermal flux facilities. The fast flux irradiated encapsulated fuel pins continue to provide valuable data and insight into FCCI. Currently, however, bare pins with prototypic fuels and cladding irradiated in the fast flux Experimental Breeder Reactor-II (EBR-II) as multiple pin assemblies under prototypic powers, temperatures and thermal gradients are providing growing quantities of data on FCCI characteristics and cladding thickness losses from FCCI. A few special encapsulated fuel pin tests are being conducted in the General Electric Test Reactor (GETR) and EBR-II, but these are aimed at providing specific information under irradiation conditions not achievable in the fast flux bare pin assemblies or because EBR-II Operation or Safety requirements dictate that the pins be encapsulated. The discussion in this paper is limited to fast flux irradiation test results from encapsulated pins and multiple pin

Study of thermal hydraulic behavior of supercritical water flowing through fuel rod bundles

International Nuclear Information System (INIS)

Thakre, Sachin; Lakshmanan, S.P.; Kulkarni, Vinayak; Pandey, Manmohan

2009-01-01

Investigations on thermal-hydraulic behavior in Supercritical Water Reactor (SCWR) fuel assembly have obtained a significant attention in the international SCWR community because of its potential to obtain high thermal efficiency and compact design. Present work deals with CFD analysis to study the flow and heat transfer behavior of supercritical water in 4 metre long 7-pin fuel bundle using commercial CFD package ANSYS CFX for single phase steady state conditions. Considering the symmetric conditions, 1/12th part of the fuel rod bundle is taken as a domain of analysis. RNG K-epsilon model with scalable wall functions is used for modeling the turbulence behavior. Constant heat flux boundary condition is applied at the fuel rod surface. IAPWS equations of state are used to compute thermo-physical properties of supercritical water. Sharp variations in its thermo-physical properties (specific heat, density) are observed near the pseudo-critical temperature causing sharp change in heat transfer coefficient. The pseudo-critical point initially appears in the gaps among heated fuel rods, and then spreads radially outward reaching the adiabatic wall as the flow goes downstream. The enthalpy gain in the centre of the channel is much higher than that in the wall region. Non-uniformity in the circumferential distribution of surface temperature and heat transfer coefficient is observed which is in agreement with published literature. Heat transfer coefficient is high on the rod surface near the tight region and decreases as the distance between rod surfaces increases. (author)

Investigation into fuel pin reshuffling options in PWR in-core fuel management for enhancement of efficient use of nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Daing, Aung Tharn, E-mail: atdaing@khu.ac.kr; Kim, Myung Hyun, E-mail: mhkim@khu.ac.kr

2014-07-01

Highlights: • This paper discusses an alternative option, fuel pin reshuffling for maximization of cycle energy production. • The prediction results of isotopic compositions of each burnt pin are verified. • The operating performance is analyzed at equilibrium core with fuel pin reshuffling. • The possibility of reuse of spent fuel pins for reduction of fresh fuel assemblies is investigated. - Abstract: An alternative way to enhance efficient use of nuclear fuel is investigated through fuel pin reshuffling options within PWR fuel assembly (FA). In modeling FA with reshuffled pins, as prerequisite, the single pin calculation method is proposed to estimate the isotopic compositions of each pin of burnt FA in the core-wide environment. Subsequently, such estimation has been verified by comparing with the neutronic performance of the reference design. Two scenarios are concerned, i.e., first scenario was targeted on the improvement of the uniform flux spatial distribution and on the enhancement of neutron economy by simply reshuffling the existing fuel pins in once-burnt fuel assemblies, and second one was focused on reduction of fresh fuel loading and discharged fuel assemblies with more economic incentives by reusing some available spent fuel pins still carrying enough reactivity that are mechanically sound ascertained. In scenario-1, the operating time was merely somewhat increased for few minutes when treating eight FAs by keeping enough safety margins. The scenario-2 was proved to reduce four fresh FAs loading without largely losing any targeted parameters from the safety aspect despite loss of 14 effective full power days for operation at reference plant full rated power.

Equipment for detach the fuel elements of the irradiated candu fuel bundle

International Nuclear Information System (INIS)

Cojocaru, V.; Dinuta, G.

2013-01-01

Monitoring the behaviour of the fuel bundles during their combustion provides useful information for the operation of the nuclear power plant as well as for the fuel manufacturer. Before placing it inside the reactor, the fuel bundle is inspected visually, dimensionally and, during combustion in the reactor, its radioactive behaviour is monitored. The purpose of the presented equipment is to allow the visual external inspection of the damaged fuel bundle in order to identify visible defects and to detach the fuel element by breaking the welded connection between the cap and grid. These devices are operated using the handler devices already existing in the hot cells Post-Irradiation Examination Laboratory (LEPI). This equipment has been used successfully in the LEPI laboratory at SCN Pitesti to inspect the damaged fuel from Cernavoda NPP, in March 2013. (authors)

Development of vibropac MOX fuel pins serviceable up TP superhigh burnups

International Nuclear Information System (INIS)

Mayorshin, A.A.; Gadzhiev, G.I.; Kisly, V.A.; Skiba, O.V.; Tzykanov, V.A.

1998-01-01

The main results on investigations of fast reactor fuel pins with (UPu)O 2 vibropac fuel to substantiate their serviceability up to the super-high burnups are presented. The BOR-60 reactor fuel pins radiation behaviour in stationary, transient and designed emergency conditions has been determined from the fuel pins dimensional stability analysis having regard to the results of investigation fuel and cladding swelling as well as estimations of fuel and cladding thermal-mechanical and physico-chemical interactions. It is shown that the change of the outer diameter is minimum in fuel pins with VMOX fuel with a getter-metallic uranium powder and ferrito-martensite steel cladding, and the corrosion damage of the cladding inner surface is absent up to 26% h.a. The experiments with over-heating of the irradiated fuel pins cladding up to 850 deg. C did not lead to any changes in pins integrity. The availability of the periphery area of the vibropac fuel cure initial structure provides the minimum level of the thermal-mechanical stress at transient conditions of reactor operation. (author)

Peripheral pin alignment system for fuel assemblies

International Nuclear Information System (INIS)

Anthony, A.J.

1981-01-01

An alignment system is provided for nuclear fuel assemblies in a nuclear core. The core support structure of the nuclear reactor includes upwardly pointing alignment pins arranged in a square grid and engage peripheral depressions formed in the lateral periphery of the lower ends of each of the fuel assemblies of the core. In a preferred embodiment, the depressions are located at the corners of the fuel assemblies so that each depression includes one-quarter of a cylindrical void. Accordingly, each fuel assembly is positioned and aligned by one-quarter of four separate alignment pins which engage the fuel assemblies at their lower exterior corners. (author)

Fabrication of the instrumented fuel rods for the 3-Pin Fuel Test Loop at HANARO

International Nuclear Information System (INIS)

Sohn, Jae Min; Park, Sung Jae; Shin, Yoon Tag; Lee, Jong Min; Ahn, Sung Ho; Kim, Soo Sung; Kim, Bong Goo; Kim, Young Ki; Lee, Ki Hong; Kim, Kwan Hyun

2008-09-01

The 3-Pin Fuel Test Loop(hereinafter referred to as the '3-Pin FTL') facility has been installed at HANARO(High-flux Advanced Neutron Application Reactor) and the 3-Pin FTL is under a test operation. The purpose of this report is to fabricate the instrumented fuel rods for the 3-Pin FTL. The fabrication of these fuel rods was based on experiences and technologies of the instrumented fuel rods for an irradiation fuel capsule. The three instrumented fuel rods of the 3-Pin FTL have been designed. The one fuel rod(180 .deg. ) was designed to measure the centerline temperature of the nuclear fuels and the internal pressure of the fuel rod, and others(60 .deg. and 300 .deg. ) were designed to measure the centerline temperature of the fuel pellets. The claddings were made of the reference material 1 and 2 and new material 1 and 2. And nuclear fuel was used UO 2 (2.0w/o) pellet type with large grain and standard grain. The major procedures of fabrication are followings: (1) the assembling and weld of fuel rods with the pellet mockups and the sensor mockups for the qualification tests, (2) the qualification tests(dimension measurements, tensile tests, metallography examinations and helium leak tests) of weld, (3) the assembling and weld of instrumented fuel rods with the nuclear pellets and the sensors for the irradiation test, and (4) the qualification tests(the helium leak test, the dimensional measurement, electric resistance measurements of sensors) of test fuel rods. Satisfactory results were obtained for all the qualification tests of the instrumented fuel rods for the 3-Pin FTL. Therefore the three instrumented fuel rods for the 3-Pin FTL have been fabricated successfully. These will be installed in the In-Pile Section of 3-Pin FTL. And the irradiation test of these fuel rods is planned from the early next year for about 3 years at HANARO

Some aspects of continuum physics used in fuel pin modeling

International Nuclear Information System (INIS)

Bard, F.E.

1975-06-01

The mathematical formulation used in fuel pin modeling is described. Fuel pin modeling is not a simple extension of the experimental and interpretative methods used in classical mechanics. New concepts are needed to describe materials in a reactor environment. Some aspects of continuum physics used to develop these new constitutive equations for fuel pins are presented. (U.S.)

Development of a new bundle welding technology for CANDU fuels

International Nuclear Information System (INIS)

Kim, Soo Sung; Lee, D. Y.; Goo, D. S.

2010-01-01

The new technology of welding process for fuel bundle of CANDU nuclear fuels is considered important in respect to the soundness of weldments and the improvement of the performance of nuclear fuels during the operation in reactor. The probability of leakage of the fission products is mostly apt to occur at the weldments of fuel bundles, and it is connected directly with the safety and life prediction of the nuclear reactor in operation. The fuel bundles of CANDU nuclear fuels are welded by the electrical resistance method, connecting the endplates and endcaps with fuel rods. Therefore, the purpose of this study of the 2nd year is to select the proper welding parameters and to investigate the characteristics of the full-sized samples using the projection endplates and make some prototype samples for the endplate welding of CANDU nuclear fuels. This study will be also provide the fundamental data for the new design and fabrications of CANDU nuclear fuel bundles

Fuel sub-assembly

International Nuclear Information System (INIS)

Jolly, R.

1982-01-01

A fuel sub-assembly for a liquid metal cooled nuclear reactor is described in which the bundle of fuel pins are braced apart by a series of spaced grids. The grids at the lower end are capable of yielding, thus allowing pins swollen by irradiation to be withdrawn with a reduced risk of damage. (U.K.)

Steady-state thermohydraulic studies in seven-pin bundle out-of-pile experiments: nominal and distorted geometry tests

International Nuclear Information System (INIS)

Falzetti, L.; Meneghello, S.; Pezzilli, M.

1979-01-01

Two sets of experiments have been performed in sodium with two seven pin electrically heated bundles: the first with a nominal arrangement, the second with one dummy pin enlarged 20% in diameter in peripheral position. In this paper a rapid review of experimental results and theoretical works, related to the temperature distribution in these geometries, is presented together with a short description of the developed test section technology

A comprehensive in-pile test of PWR fuel bundle

Energy Technology Data Exchange (ETDEWEB)

Kang Rixin; Zhang Shucheng; Chen Dianshan (Academia Sinica, Beijing (China). Inst. of Atomic Energy)

1991-02-01

An in-pile test of PWR fuel bundle has been conducted in HWRR at IAE of China. This paper describes the structure of the test bundle (3x3-2), fabrication process and quality control of the fuel rod, irradiation conditions and the main Post Irradiation Examination (PIE) results. The test fuel bundle was irradiated under the PWR operation and water chemistry conditions with an average linear power of 381 W/cm and reached an average burnup of 25010 MWd/tU of the fuel bundle. After the test, destructive and non-destructive examination of the fuel rods was conducted at hot laboratories. The fission gas release was 10.4-23%. The ridge height of cladding was 3 to 8 {mu}m. The hydrogen content of the cladding was 80 to 140 ppm. The fuel stack height was increased by 2.9 to 3.3 mm. The relative irradiation growth was about 0.11 to 0.17% of the fuel rod length. During the irradiation test, no fuel rod failure or other abnormal phenomena had been found by the on-line fuel failure monitoring system of the test loop and water sampling analysis. The structure of the test fuel assembly was left undamaged without twist and detectable deformation. (orig.).

Nuclear fuel assemblies and fuel pins usable in such assemblies

International Nuclear Information System (INIS)

Jolly, R.

1982-01-01

A novel end cap for a nuclear fuel assembly is described in detail. It consists of a trisection arrangement which is received within a cell of a cellular grid. The cell contains abutment means with which the trisection comes into abutment. The grid also contains an abutment means for preventing the trisections from being inserted into the cell in an incorrect orientation. The present design allows fuel pins to be securely held in a hold-down grid of a sub-assembly. The design also allows easier dis-assembly of the swollen and embrittled fuel pins prior to reprocessing. (U.K.)

Manufacturing of 37-element fuel bundles for PHWR 540 - new approach

Energy Technology Data Exchange (ETDEWEB)

Arora, U.K.; Sastry, V.S.; Banerjee, P.K.; Rao, G.V.S.H.; Jayaraj, R.N. [Nuclear Fuel Complex, Dept. Atomic Energy, Government of India, Hyderabad (India)

2003-07-01

Nuclear Fuel Complex (NFC), established in early seventies, is a major industrial unit of Department of Atomic Energy. NFC is responsible for the supply of fuel bundles to all the 220 MWe PHWRs presently in operation. For supplying fuel bundles for the forthcoming 540 MWe PHWRs, NEC is dovetailing 37-element fuel bundle manufacturing facilities in the existing plants. In tune with the philosophy of self-reliance, emphasis is given to technology upgradation, higher customer satisfaction and application of modern quality control techniques. With the experience gained over the years in manufacturing 19-element fuel bundles, NEC has introduced resistance welding of appendages on fuel tubes prior to loading of UO{sub 2} pellets, use of bio-degradable cleaning agents, simple diagnostic tools for checking the equipment condition, on line monitoring of variables, built-in process control methods and total productive maintenance concepts in the new manufacturing facility. Simple material handling systems have been contemplated for handling of the fuel bundles. This paper highlights the flow-sheet adopted for the process, design features of critical equipment and the methodology for fabricating the 37-element fuel bundles, 'RIGHT FIRST TIME'. (author)

Manufacturing of 37-element fuel bundles for PHWR 540 - new approach

International Nuclear Information System (INIS)

Arora, U.K.; Sastry, V.S.; Banerjee, P.K.; Rao, G.V.S.H.; Jayaraj, R.N.

2003-01-01

Nuclear Fuel Complex (NFC), established in early seventies, is a major industrial unit of Department of Atomic Energy. NFC is responsible for the supply of fuel bundles to all the 220 MWe PHWRs presently in operation. For supplying fuel bundles for the forthcoming 540 MWe PHWRs, NEC is dovetailing 37-element fuel bundle manufacturing facilities in the existing plants. In tune with the philosophy of self-reliance, emphasis is given to technology upgradation, higher customer satisfaction and application of modern quality control techniques. With the experience gained over the years in manufacturing 19-element fuel bundles, NEC has introduced resistance welding of appendages on fuel tubes prior to loading of UO 2 pellets, use of bio-degradable cleaning agents, simple diagnostic tools for checking the equipment condition, on line monitoring of variables, built-in process control methods and total productive maintenance concepts in the new manufacturing facility. Simple material handling systems have been contemplated for handling of the fuel bundles. This paper highlights the flow-sheet adopted for the process, design features of critical equipment and the methodology for fabricating the 37-element fuel bundles, 'RIGHT FIRST TIME'. (author)

Development of wire wrapping technology for FBR fuel pin

International Nuclear Information System (INIS)

Nogami, Tetsuya; Seki, Nobuo; Sawayama, Takeo; Ishibashi, Takashi

1991-01-01

For the FBR fuel assembly, the spacer wire is adopted to maintain the space between fuel pins. The developments have been carried out to achieve automatically wire wrapping with high precision. Based on the fundamental technology developed through the mock-up test operation, Joyo 'MK-I', fuel pin fabrication was started using partially mechanized wire wrapping machine in 1973. In 1978, an automated wire wrapping machine for Joyo 'MK-II' was developed by the adoption of some improvements for the wire inserting system to end plug hole and the precision of wire pitch. On the bases of these experiences, fully automated wire wrapping machine for 'Monju' fuel pin was installed at Plutonium Fuel Production Facility (PFPF) in 1987. (author)

SEU43 fuel bundles in CANDU 600

International Nuclear Information System (INIS)

Catana, Alexandru; Prodea, Iosif; Danila, Nicolae; Prisecaru, Ilie; Dupleac, Daniel

2008-01-01

Cernavoda Unit 1 and Unit 2 are pressure tube 650 MWe nuclear stations moderated and cooled with heavy water, of Canada design, located in Romania. Fuelling is on-power and the plant is currently fuelled with natural uranium dioxide. Fuel is encapsulated in a 37 fuel rod assembly having a specific standard geometry (STD37). In order to reduce fuel cycle costs programs were initiated in Canada, South Korea and at SCN Pitesti, Romania for design and build of a new, improved geometry fuel bundle and some fuel compositions. Among fuel compositions, which are considered, is the slightly enriched uranium (SEU) fuel (0.96 w% U-235) with an associated burn-up increase from ∼7900 MWd/tU up to ∼15000 MWd/tU. Neutron analysis showed that the Canadian-Korean fuel bundle geometry with 43 rods called SEU (SEU43) can be used in already operated reactors. A new fuel bundle resulted. Extended, comprehensive analysis must be conducted in order to assess the TH behavior of SEU43 besides the neutron, mechanical (drag force, etc) analyses. In this paper, using the sub-channel approach, main thermal-hydraulic parameters were analyzed: pressure drop; fuel, sheath and coolant temperatures; coolant density; critical heat flux. Some significant differences versus standard fuel are outlined in the paper and some conclusions are drawn. While, by using this new fuel, there are many benefits to be attained like: fuel costs reduction, spent fuel waste minimization, increase in competitiveness of nuclear power generation against other sources of generation, etc., the safety margins must be, at least, conserved. The introduction of a new fuel bundle type, different in geometry and fuel composition, requires a detailed preparation, a testing program and a series of neutron and thermal-hydraulic analysis. The results reported by this paper is part of this effort. The feasibility to increase the enrichment from 0.71% U-235 (NU) to 0.96% U-235, with an estimated burn-up increase up to 14000 MWd

Optimization of a fuel bundle within a CANDU supercritical water reactor

International Nuclear Information System (INIS)

Schofield, M.E.

2009-01-01

The supercritical water reactor is one of six nuclear reactor concepts being studied under the Generation IV International Forum. Generation IV nuclear reactors will improve the metrics of economics, sustainability, safety and reliability, and physical protection and proliferation resistance over current nuclear reactor designs. The supercritical water reactor has specific benefits in the areas of economics, safety and reliability, and physical protection. This work optimizes the fuel composition and bundle geometry to maximize the fuel burnup, and minimize the surface heat flux and the form factor. In optimizing these factors, improvements can be achieved in the areas of economics, safety and reliability of the supercritical water reactor. The WIMS-AECL software was used to model a fuel bundle within a CANDU supercritical water reactor. The Gauss' steepest descent method was used to optimize the above mentioned factors. Initially the fresh fuel composition was optimized within a 43-rod CANFLEX bundle and a 61-rod bundle. In both the 43-rod and 61-rod bundle scenarios an online refuelling scheme and non-refuelling scheme were studied. The geometry of the fuel bundles was then optimized. Finally, a homogeneous mixture of thorium and uranium fuel was studied in a 60-rod bundle. Each optimization process showed definitive improvements in the factors being studied, with the most significant improvement being an increase in the fuel burnup. The 43-rod CANFLEX bundle was the most successful at being optimized. There was little difference in the final fresh fuel content when comparing an online refuelling scheme and non-refuelling scheme. Through each optimization scenario the ratio of the fresh fuel content between the annuli was a significant determining cause in the improvements in the factors being optimized. The geometry optimization showed that improvement in the design of a fuel bundle is indeed possible, although it would be more advantageous to pursue it

Modeling of fuel bundle vibration and the associated fretting wear in a CANDU fuel channel

International Nuclear Information System (INIS)

Mohany, A.; Hassan, M.

2011-01-01

In this paper a numerical model is developed to predict the vibration response of a CANDU® fuel bundle and the associated fretting wear in the surrounding pressure tube. One excitation mechanism is considered in this model; turbulence-induced excitation caused by coolant flow inside the fuel channel. The numerical model can be easily adapted to include the effects of seismic events, fuel bundle impact during refuelling and start-up of the reactor, and the acoustic pressure pulsations caused by the primary heat transport (PHT) pumps. The simulation is performed for a typical CANDU fuel bundle with 37 fuel elements. The clearances between the buttons of the inner fuel elements, and between the bearing pads of the outer fuel elements and the pressure tube were measured from an actual fuel bundle. Some variability among the measured clearance values was observed. Therefore, probability density functions of the measured clearance values were established and the simulation was performed for the probabilistic distribution of the clearance values. The contact between the fuel bundle and the pressure tube is modeled using pseudo-force contact method. The proposed modelling technique can be used in future CANDU reactors to avoid fuel and pressure tube fretting damage due to the aforementioned excitation mechanisms. (author)

Fuel sub-assembly

International Nuclear Information System (INIS)

Jolly, R.

1988-01-01

A nuclear fuel sub-assembly includes a hexagonal bundle of parallel, spaced apart fuel pins coupled at one end to an end-holding grid comprising a number of transverse spaced apart rails to each of which is connected a series of pin-receiving cells which render the pins axially captive with the rails. The series of cells are defined by a pair of metal strips each of which has a series of pocket formations such that when the pocket formations are in registry they define cylindrical shaped cells provided with internal projections which engage annular recesses in the end caps of the fuel pins to effect axial constraint of the pins. (author)

An assessment of thermal behavior of the DUPIC fuel bundle by subchannel analysis

International Nuclear Information System (INIS)

Park, Jee Won.

1997-12-01

Thermal behavior of the standard DUPIC fuel has been assessed. The DUPIC fuel bundle has been modeled for a subchannel analysis using the ASSERT-IV code which was developed by AECL. From the calculated mixture enthalpy, equilibrium quality and void fraction distributions of the DUPIC fuel bundle, it is found that net buoyancy effect is pronounced in the central region of the DUPIC fuel bundle when compared with the standard CANDU fuel bundle. It is also found that the central region of the DUPIC fuel bundle can be cooled more efficiently than that of the standard fuel bundle. Based upon the subchannel modeling used in this study, the location of minimum CHFR in the DUPIC fuel bundle has been found to be very similar to that of the standard fuel. From the calculated mixture enthalpy distribution at the exit of the fuel channel, it is found that the mixture enthalpy and void fraction can be highest in the peripheral region of the DUPIC fuel bundle. On the other hand, the enthalpy and the void fraction was found to be highest in the central region of the standard CANDU fuel bundle at the exit of the fuel channel. Since the transverse interchange model between subchannels is important for the behavior of these variables, it is needed to put more effort in validating the transverse interchange model. For the purpose of investigating influence of thermal-hydraulic parameter variations of the DUPIC fuel bundle, four different values of the channel flow rates were used in the subchannel analysis. The effect of the channel flow reduction on thermal-hydraulic parameters have been presented. This study shows that the subchannel analysis is very useful in assessing thermal behavior of the fuel bundles in CANDU reactors. (author). 12 refs., 3 tabs., 17 figs

Shield requirement estimation for pin storage room in fuel fabrication plant

International Nuclear Information System (INIS)

Shanthi, M.M.; Keshavamurthy, R.S.; Sivashankaran, G.

2012-01-01

Fast Reactor Fuel Cycle Facility (FRFCF) is an upcoming project in Kalpakkam. It has the facility to recycle the fuel from PFBR. It is an integrated facility, consists of fuel reprocessing plant, fuel fabrication plant (FFP), core subassembly plant, Reprocessed Uranium plant (RUP) and waste management plant. The spent fuel from PFBR would be reprocessed in fuel reprocessing plant. The reprocessed fuel material would be sent to fuel fabrication plant. The main activity of fuel fabrication plant is the production of MOX fuel pins. The fuel fabrication plant has a fuel pin storage room. The shield requirement for the pin storage room has been estimated by Monte Carlo method. (author)

Irradiation of TZM: Uranium dioxide fuel pin at 1700 K

Science.gov (United States)

Mcdonald, G. E.

1973-01-01

A fuel pin clad with TZM and containing solid pellets of uranium dioxide was fission heated in a static helium-cooled capsule at a maximum surface temperature of 1700 K for approximately 1000 hr and to a total burnup of 2.0 percent of the uranium-235. The results of the postirradiation examination indicated: (1) A transverse, intergranular failure of the fuel pin occurred when the fuel pin reached 2.0-percent burnup. This corresponds to 1330 kW-hr/cu cm, where the volume is the sum of the fuel, clad, and void volumes in the fuel region. (2) The maximum swelling of the fuel pin was less than 1.5 percent on the fuel-pin diameter. (3) There was no visible interaction between the TZM clad and the UO2. (4) Irradiation at 1700 K produced a course-grained structure, with an average grain diameter of 0.02 centimeter and with some of the grains extending one-half of the thickness of the clad. (5) Below approximately 1500 K, the irradiation of the clad produced a moderately fine-grained structure, with an average grain diameter of 0.004 centimeter.

Nuclear fuel sub-assemblies

International Nuclear Information System (INIS)

Dodd, J.A.; Butterfield, C.E.; Waite, E.

1979-01-01

A fast reactor fuel sub-assembly has honeycomb grids for laterally supporting the fuel pins. The grids are of two series and are arranged alternately along the bundle. The grids of a first series provide a discrete cell for each pin but the grids of the second series have a peripheral group of cells only. The grids of the second series provide intermediate support of the edge pins to restrain bow. (author)

Fuel pellet relocation behavior in fast reactor uranium-plutonium mixed oxide fuel pin at beginning-of-life

International Nuclear Information System (INIS)

Inoue, Masaki; Ukai, Shigeharu; Asaga, Takeo

1999-08-01

The effects of fabrication parameters, irradiation conditions and fuel microstructural feature on fuel pellet relocation behavior in fast reactor fuel pins were investigated. This work focused only on beginning-of-life conditions, when fuel centerline temperature depends largely on the behavior. Fuel pellet relocation behavior in Joyo Mk-II driver could not be characterized because of the lack of data. And the behavior in FFTF driver and its larger diameter type fuel pins could not be characterized because of the extensive lot-by-lot scatters. The behavior both in Monju type and in Joyo power-to-melt type fuel pins were similar to each other, and depends largely on the as-fabricated gap width while the effects of linear heat rate and the extent of microstructural evolution were negligible. And fuel pellet centerline melting seems to affect slightly the behavior. The correlation, which describes the extent of relocation both in Monju type and in Joyo power-to-melt type fuel pins, were newly formulated and extrapolated for Joyo Mk-II driver, FFTF driver and its larger diameter type fuel pins. And the behavior in Joyo Mk-II driver seemed to be similar. On the contrary, the similarity with JNC fuel pins was observed case-by-case in FFTF driver and its larger diameter type fuel pins. (author)

Fabrication of Fast Reactor Fuel Pins for Test Irradiations

Energy Technology Data Exchange (ETDEWEB)

Karsten, G. [Institute for Applied Reactor Physics, Kernforschungszentrum Karlsruhe, Karlsruhe, Federal Republic of Germany (Germany); Dippel, T. [Institute for Radiochemistry, Kernforschungszentrum Karlsruhe, Karlsruhe, Federal Republic of Germany (Germany); Laue, H. J. [Institute for Applied Reactor Physics, Kernforschungszentrum Karlsruhe, Karlsruhe, Federal Republic of Germany (Germany)

1967-09-15

An extended irradiation programme is being carried out for the fuel element development of the Karlsruhe fast breeder project. A very important task within the programme is the testing of plutonium-containing fuel pins in a fast-reactor environment. This paper deals with fabrication of such pins by our laboratories at Karlsruhe. For the fast reactor test positions at present envisaged a fuel with 15% plutonium and the uranium fully enriched is appropriate. Hie mixed oxide is both pelletized and vibro-compacted with smeared densities between 80 and 88% theoretical. The pin design is, for example, such that there are two gas plena at the top and bottom, and one blanket above the fuel with the fuel zone fitting to the test reactor core length. The specifications both for fuel and cladding have been adapted to the special purpose of a fast-breeder reactor - the outer dimensions, the choice of cladding and fuel types, the data used and the kind of tests outline the targets of the development. The fuel fabrication is described in detail, and also the powder line used for vibro-compaction. The source materials for the fuel are oxalate PuO{sub 2} and UO{sub 2} from the UF{sub 6} process. The special problems of mechanical mixing and of plutonium homogeneity have been studied. The development of the sintering technique and grain characteristics for vibratory compactive fuel had to overcome serious problems in order to reach 82-83% theoretical. The performance of the pin fabrication needed a major effort in welding, manufacturing of fits and decontamination of the pin surfaces. This was a stimulation for the development of some very subtle control techniques, for example taking clear X-ray photographs and the tube testing. In general the selection of tests was a special task of the production routine. In conclusion the fabrication of the pins resulted in valuable experiences for the further development of fast reactor fuel elements. (author)

Interactive hypermedia training manual for spent-fuel bundle counters

International Nuclear Information System (INIS)

Basso, R.A.

1990-07-01

Spent-fuel bundle counters, developed by the Canadian Safeguards Support Program for the International Atomic Energy Agency, provide a secure and independent means of counting the number of irradiated fuel bundles discharged into the fuel storage bays at CANDU nuclear power stations. Paper manuals have been traditionally used to familiarize IAEA inspectors with the operation, maintenance and extensive reporting capabilities of the bundle counters. To further assist inspectors, an interactive training manual has been developed on an Apple Macintosh computer using hypermedia software. The manual uses interactive animation and sound, in conjunction with the traditional text and graphics, to simulate the underlying operation and logic of the bundle counters. This paper presents the key features of the interactive manual and highlights the advantages of this new technology for training

Criticality safety studies for plutonium–uranium metal fuel pin fabrication facility

International Nuclear Information System (INIS)

Stephen, Neethu Hanna; Reddy, C.P.

2013-01-01

Highlights: ► Criticality safety limits for PUMP-F facility is identified. ► The fissile mass which can be handled safely during alloy preparation is 10.5 kg. ► The number of fuel slugs which can be handled safely during injection casting is 53. ► The number of fuel slugs which can be handled safely after fuel fabrication is 71. - Abstract: This study focuses on the criticality safety during the fabrication of fast reactor metal fuel pins comprising of the fuel type U–15Pu, U–19Pu and U–19Pu–6Zr in the Plutonium–Uranium Metal fuel Pin fabrication Facility (PUMP-F). Maximum amount of fissile mass which can be handled safely during master alloy preparation, Injection casting and fuel slug preparation following fuel pin fabrication were identified and fixed based on this study. In the induction melting furnace, the fissile mass can be limited to 10.5 kg. During fuel slug preparation and fuel pin fabrication, fuel slugs and pins were arranged in hexagonal and square lattices to identify the most reactive configuration. The number of fuel slugs which can be handled safely after injection casting can be fixed to be 53, whereas after fuel fabrication it is 71

Fabrication and characterization of MX-type fuels and fuel pins

International Nuclear Information System (INIS)

Richter, K.; Bartscher, W.; Benedict, U.; Gueugnon, J.F.; Kutter, H.; Sari, C.; Schmidt, H.E.

1978-01-01

This paper summarizes the most important fabrication parameters and characterization of fuel and fuel pins obtained during the investigation of uranium-plutonium carbides, oxicarbides, carbonitrides and nitrides in the past years at the European Institute for Transuranium Elements at Karlsruhe. All preparation methods discussed are based on carbothermic reduction of a mechanical blend of uranium-plutonium oxide and carbon powder. General data for carbothermic reduction processes are discussed (influence of starting material, homogeneity, control of degree of reaction, etc). A survey of different preparation methods investigated is given. Limitations with respect to temperature and atmosphere for both carbothermic reduction processes and sintering conditions for the different compounds are summarized. A special preparation process for mixed carbonitrides with low nitrogen content (U,Pu)sub(1-x)Nsub(x) in the range 0.1 0 C to 1400 0 C by means of a modulated electron beam technique. A scheme is proposed, which allows to predict the thermal properties of MX fuels on the basis of their chemical composition and porosity. Preparation, preirradiation characterization and final controls of fuel test pins for pellet and vibrocompacted type of pins are described and the most important data summarized for all advanced fuels irradiated at Dounreay (DN1) and Rapsodie Fast Reactor (DN2) within the TU irradiation programme

Fuel rod bundles proposed for advanced pressure tube nuclear reactors

International Nuclear Information System (INIS)

Prodea, Iosif; Catana, Alexandru

2010-01-01

The paper aims to be a general presentation for fuel bundles to be used in Advanced Pressure Tube Nuclear Reactors (APTNR). The characteristics of such a nuclear reactor resemble those of known advanced pressure tube nuclear reactors like: Advanced CANDU Reactor (ACR TM -1000, pertaining to AECL) and Indian Advanced Heavy Water Reactor (AHWR). We have also developed a fuel bundle proposal which will be referred as ASEU-43 (Advanced Slightly Enriched Uranium with 43 rods). The ASEU-43 main design along with a few neutronic and thermalhydraulic characteristics are presented in the paper versus similar ones from INR Pitesti SEU-43 and CANDU-37 standard fuel bundles. General remarks regarding the advantages of each fuel bundle and their suitability to be burned in an APTNR reactor are also revealed. (authors)

Advanced disassembling technique of irradiated driver fuel assembly for continuous irradiation of fuel pins

International Nuclear Information System (INIS)

Ichikawa, Shoichi; Haga, Hiroyuki; Katsuyama, Kozo; Maeda, Koji; Nishinoiri, Kenji

2012-01-01

It was necessary to carry out continuous irradiation tests in order to obtain the irradiation data of high burn-up fuel and high neutron dose material for FaCT (Fast Reactor Cycle Technology Development) project. There, the disassembling technique of an irradiated fuel assembly was advanced in order to realize further continuous irradiation tests. Although the conventional disassembling technique had been cutting a lower end-plug of a fuel pin needed to fix fuel pins to an irradiation vehicle, the advanced disassembling technique did not need cutting a lower end-plug. As a result, it was possible to supply many irradiated fuel pins to various continuous irradiation tests for FaCT project. (author)

Performance of advanced oxide fuel pins in EBR-II

International Nuclear Information System (INIS)

Lawrence, L.A.; Jensen, S.M.; Hales, J.W.; Karnesky, R.A.; Makenas, B.J.

1986-05-01

The effects of design and operating parameters on mixed-oxide fuel pin irradiation performance were established for the Hanford Engineering Development Laboratory (HEDL) advanced oxide EBR-II test series. Fourteen fuel pins breached in-reactor with reference 316 SS cladding. Seven of the breaches are attributed to FCMI. Of the remaining seven breached pins, three are attributed to local cladding over-temperatures similar to the breach mechanism for the reference oxide pins irradiated in EBR-II. FCCI was found to be a contributing factor in two high burnup, i.e., 11.7 at. % breaches. The remaining two breaches were attributed to mechanical interaction of UO 2 fuel and fission products accumulated in the lower cladding insulator gap, and a loss of cladding ductility possibly due to liquid metal embrittlement. Fuel smear density appears to have the most significant impact on lifetime. Quantitative evaluations of cladding diameter increases attributed to FCMI, established fuel smear density, burnup, and cladding thickness-to-diameter ratio as the major parameters influencing the extent of cladding strain

Timing analysis of PWR fuel pin failures

International Nuclear Information System (INIS)

Jones, K.R.; Wade, N.L.; Katsma, K.R.; Siefken, L.J.; Straka, M.

1992-09-01

Research has been conducted to develop and demonstrate a methodology for calculation of the time interval between receipt of the containment isolation signals and the first fuel pin failure for loss-of-coolant accidents (LOCAs). Demonstration calculations were performed for a Babcock and Wilcox (B ampersand W) design (Oconee) and a Westinghouse (W) four-loop design (Seabrook). Sensitivity studies were performed to assess the impacts of fuel pin bumup, axial peaking factor, break size, emergency core cooling system availability, and main coolant pump trip on these times. The analysis was performed using the following codes: FRAPCON-2, for the calculation of steady-state fuel behavior; SCDAP/RELAP5/MOD3 and TRACPF1/MOD1, for the calculation of the transient thermal-hydraulic conditions in the reactor system; and FRAP-T6, for the calculation of transient fuel behavior. In addition to the calculation of fuel pin failure timing, this analysis provides a comparison of the predicted results of SCDAP/RELAP5/MOD3 and TRAC-PFL/MOD1 for large-break LOCA analysis. Using SCDAP/RELAP5/MOD3 thermal-hydraulic data, the shortest time intervals calculated between initiation of containment isolation and fuel pin failure are 10.4 seconds and 19.1 seconds for the B ampersand W and W plants, respectively. Using data generated by TRAC-PF1/MOD1, the shortest intervals are 10.3 seconds and 29.1 seconds for the B ampersand W and W plants, respectively. These intervals are for a double-ended, offset-shear, cold leg break, using the technical specification maximum peaking factor and applied to fuel with maximum design bumup. Using peaking factors commensurate widi actual bumups would result in longer intervals for both reactor designs. This document also contains appendices A through J of this report

Irradiated fuel bundle counter

International Nuclear Information System (INIS)

Campbell, J.W.; Todd, J.L.

1975-01-01

The design of a prototype safeguards instrument for determining the number of irradiated fuel assemblies leaving an on-power refueled reactor is described. Design details include radiation detection techniques, data processing and display, unattended operation capabilities and data security methods. Development and operating history of the bundle counter is reported

Fuel pin design algorithm for conceptual design studies

International Nuclear Information System (INIS)

Uselman, J.P.

1979-01-01

Two models are available which are currently verified by part of the requirements and which are adaptable as algorithms for the complete range. Fuel thermal performance is described by the HEDL SIEX model. Cladding damage and total deformation are determined by the GE GRO-II structural analysis code. A preliminary fuel pin performance model for analysis of (U, P/sub U/)O 2 pins in the COROPT core conceptual design system has been constructed by combining the key elements of SIEX and GRO-II. This memo describes the resulting pin performance model and its interfacing with COROPT system. Some exemplary results are presented

CFD analysis of transverse flow in a wire-wrapped hexagonal seven-pin bundle

International Nuclear Information System (INIS)

Zhao, Pinghui; Liu, Jiaming; Ge, Zhihao; Wang, Xi; Cheng, Xu

2017-01-01

Highlights: • Transverse flow in a wire-wrapped hexagonal seven-pin bundle are simulated. • Four kinds of subchannels are taken as the object. • Effects of wire number and position on transverse velocities are studied. • Parameter studies reveal P/D and H/D have a great influence than Re. • Present transverse velocity correlations need to be modified. - Abstract: Transverse flow induced by helical spacer wires has important effects on the flow and heat transfer behavior of reactor core. In this paper, transverse flow in a wire-wrapped hexagonal seven-pin bundle was simulated by the open source code, OpenFOAM, based on computational fluid dynamic (CFD) method. The Shear Stress Transport (SST) k-ω model and Spalding wall function were used to resolve the momentum field. Hexahedral dominated meshes were generated to achieve high grid quality. Periodic boundary condition and parallel processing were adopted to save the computational cost. Transverse velocity distributions in four different kinds of subchannel gaps were analyzed. The results show that the influence of wire number and position on the transverse velocity distribution is obvious. For an interior gap, transverse flow seems to be dominated by wires near the gap, and its direction changes periodically in one helical pitch. However, for a peripheral gap, transverse velocity is affected by more wires and its direction is decided by the direction of wire rotation. Parameter studies reveal that the Reynolds number (Re, at the range of 6000–100,000) has little effect on the normalized transverse flow, while the pitch to pin diameter ratio (P/D, at the range of 1.11–1.22) and the helical pitch to pin diameter ratio (H/D, at the range of 12–24) have a great influence on it, especially the P/D. Large discrepancies between our simulation results and some existing correlations were observed. This indicates that new correlations comprehensively considering both P/D and H/D effects need to be developed

CFD analysis of transverse flow in a wire-wrapped hexagonal seven-pin bundle

Energy Technology Data Exchange (ETDEWEB)

Zhao, Pinghui, E-mail: phzhao@mail.ustc.edu.cn [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230026 (China); Liu, Jiaming; Ge, Zhihao [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230026 (China); Wang, Xi; Cheng, Xu [Karlsruhe Institute of Technology, Institute of Fusion and Reactor Technologies, Kaiserstrasse 12, Karlsruhe (Germany)

2017-06-15

Highlights: • Transverse flow in a wire-wrapped hexagonal seven-pin bundle are simulated. • Four kinds of subchannels are taken as the object. • Effects of wire number and position on transverse velocities are studied. • Parameter studies reveal P/D and H/D have a great influence than Re. • Present transverse velocity correlations need to be modified. - Abstract: Transverse flow induced by helical spacer wires has important effects on the flow and heat transfer behavior of reactor core. In this paper, transverse flow in a wire-wrapped hexagonal seven-pin bundle was simulated by the open source code, OpenFOAM, based on computational fluid dynamic (CFD) method. The Shear Stress Transport (SST) k-ω model and Spalding wall function were used to resolve the momentum field. Hexahedral dominated meshes were generated to achieve high grid quality. Periodic boundary condition and parallel processing were adopted to save the computational cost. Transverse velocity distributions in four different kinds of subchannel gaps were analyzed. The results show that the influence of wire number and position on the transverse velocity distribution is obvious. For an interior gap, transverse flow seems to be dominated by wires near the gap, and its direction changes periodically in one helical pitch. However, for a peripheral gap, transverse velocity is affected by more wires and its direction is decided by the direction of wire rotation. Parameter studies reveal that the Reynolds number (Re, at the range of 6000–100,000) has little effect on the normalized transverse flow, while the pitch to pin diameter ratio (P/D, at the range of 1.11–1.22) and the helical pitch to pin diameter ratio (H/D, at the range of 12–24) have a great influence on it, especially the P/D. Large discrepancies between our simulation results and some existing correlations were observed. This indicates that new correlations comprehensively considering both P/D and H/D effects need to be developed

Los Alamos Hot-Cell-Facility modifications for examining FFTF fuel pins

International Nuclear Information System (INIS)

Campbell, B.M.; Ledbetter, J.M.

1982-01-01

Commissioned in 1960, the Wing 9 Hot Cell Facility at Los Alamos was recently modified to meet the needs of the 1980s. Because fuel pins from the Fast Flux Test Facility (FFTF) at the Hanford Engineering Development Laboratory (HEDL) are too long for examination in the original hot cells, we modified cells to accommodate longer fuel pins and to provide other capabilities as well. For instance, the T-3 shipping cask now can be opened in an inert atmosphere that can be maintained for all nondestructive and destructive examinations of the fuel pins. The full-length pins are visually examined and photographed, the wire wrap is removed, and fission gas is sampled. After the fuel pin is cropped, a cap is seal-welded on the section containing the fuel column. This section is then transferred to other cells for gamma-scanning, radiography, profilometry, sectioning for metallography, and chemical analysis

Irradiated fuel bundle counter

International Nuclear Information System (INIS)

Campbell, J.W.; Todd, J.L.

1975-01-01

The design of a prototype safeguards instrument for determining the number of irradiated fuel assemblies leaving an on-power refueled reactor is described. Design details include radiation detection techniques, data processing and display, unattended operation capabilities and data security methods. Development and operating history of the bundle counter is reported. (U.S.)

Fabrication of oxide dispersion strengthened ferritic clad fuel pins

International Nuclear Information System (INIS)

Zirker, L.R.; Bottcher, J.H.; Shikakura, S.; Tsai, C.L.

1991-01-01

A resistance butt welding procedure was developed and qualified for joining ferritic fuel pin cladding to end caps. The cladding are INCO MA957 and PNC ODS lots 63DSA and 1DK1, ferritic stainless steels strengthened by oxide dispersion, while the end caps are HT9 a martensitic stainless steel. With adequate parameter control the weld is formed without a residual melt phase and its strength approaches that of the cladding. This welding process required a new design for fuel pin end cap and weld joint. Summaries of the development, characterization, and fabrication processes are given for these fuel pins. 13 refs., 6 figs., 1 tab

Pressure drop redistribution experimental analysis in axial flow along the bundles

International Nuclear Information System (INIS)

Bastos Franco, C. de; Carajilescov, P.

1992-01-01

Fuel elements of PWR type nuclear reactors are composed of rod bundles, arranged in square arrays, held by grid type spacers. The coolant flows axially along the bundle. Although such elements are laterally open, pressure drop experiments are performed in closed type test sections, originating the appearance of subchannels of different geometries. Utilizing a test section of two bundles of 4 x 4 pins and performing experiments with and without separation between the bundles, the flow redistribution factors, the friction, and the grid drag coefficients were determined for the interior subchannels. 03 refs, 06 figs, 02 tabs. (B.C.A.)

BWR fuel assembly with improved spacer and fuel bundle design for enhanced thermal-hydraulic performance

International Nuclear Information System (INIS)

Mildrum, C.M.; Taleyarkhan, R.P.

1987-01-01

In a fuel assembly having a bundle of elongated fuel rods disposed in side-by-side relationship so as to form an array of spaced fuel rods, an outer tubular flow channel surrounding the fuel rods so as to direct flow of coolant/moderator fluid along the fuel rods, a hollow water cross extending centrally through and interconnected with the outer flow channel so as to divide the channel into separate compartments and the bundle of fuelrods into a plurality of mini-bundles thereof being disposed in the compartments, and spacers axially displaced along the fuel rods in each of the mini-bundles thereof. Each spacer is composed of inner and outer means which together define spacer cells at corner, side and interior locations of the spacer and have respective protrusions formed thereon which extend into cells so as to maintain the fuel rods received through the spacer cells in laterally spaced relationships. The improvement is described which comprises: (a) a generally uniform poison coating within at least a majority of the fuel rods; (b) a predetermined pattern of fuel enrichment with respect to the fuel rods of each mini-bundle thereof which together with the uniform poison coating within the fuel rods ensures that the packing powers of the fuel rods in the corner and side cells of the spacers are less than the peaking power of a leading one of the fuel rods in the interior cells of the spacers; and (c) each of the fuel rods being received through the cells of each spacer having a diametric size smaller than that of each of the fuel rods received through the side and interior cells of each spacer, the diametric sizes of each of the fuel rods received through the side and interior cells of each spacer being generally equal

Fuel bundle for nuclear reactor

International Nuclear Information System (INIS)

Long, J.W.; Flora, B.S.; Ford, K.L.

1977-01-01

The invention concerns a new, simple and inexpensive system for assembling and dismantling a nuclear reactor fuel bundle. Several fuel rods are fitted in parallel rows between two retaining plates which secure the fuel rods in position and which are maintained in an assembled position by means of several stays fixed to the two end plates. The invention particularly refers to an improved apparatus for fixing the stays to the upper plate by using locking fittings secured to rotating sleeves which are applied against this plate [fr

CANFLEX fuel bundle cross-flow endurance test (test report)

International Nuclear Information System (INIS)

Hong, Sung Deok; Chung, C. H.; Chang, S. K.; Kim, B. D.

1997-04-01

As part of the normal refuelling sequence of CANDU nuclear reactor, both new and irradiated bundles can be parked in the cross-flow region of the liner tubes. This situation occurs normally for a few minutes. The fuel bundle which is subjected to the cross-flow should be capable of withstanding the consequences of cross flow for normal periods, and maintain its mechanical integrity. The cross-flow endurance test was conducted for CANFLEX bundle, latest developed nuclear fuel, at CANDU-Hot Test Loop. The test was carried out during 4 hours at the inlet cross-flow region. After the test, the bundle successfully met all acceptance criteria after the 4 hours cross-flow test. (author). 2 refs., 3 tabs

CANFLEX fuel bundle cross-flow endurance test (test report)

Energy Technology Data Exchange (ETDEWEB)

Hong, Sung Deok; Chung, C. H.; Chang, S. K.; Kim, B. D.

1997-04-01

As part of the normal refuelling sequence of CANDU nuclear reactor, both new and irradiated bundles can be parked in the cross-flow region of the liner tubes. This situation occurs normally for a few minutes. The fuel bundle which is subjected to the cross-flow should be capable of withstanding the consequences of cross flow for normal periods, and maintain its mechanical integrity. The cross-flow endurance test was conducted for CANFLEX bundle, latest developed nuclear fuel, at CANDU-Hot Test Loop. The test was carried out during 4 hours at the inlet cross-flow region. After the test, the bundle successfully met all acceptance criteria after the 4 hours cross-flow test. (author). 2 refs., 3 tabs.

Oxide fuel pin transient performance analysis and design with the TEMECH code

International Nuclear Information System (INIS)

Bard, F.E.; Dutt, S.P.; Hinman, C.A.; Hunter, C.W.; Pitner, A.L.

1986-01-01

The TEMECH code is a fast-running, thermal-mechanical-hydraulic, analytical program used to evaluate the transient performance of LMR oxide fuel pins. The code calculates pin deformation and failure probability due to fuel-cladding differential thermal expansion, expansion of fuel upon melting, and fission gas pressurization. The mechanistic fuel model in the code accounts for fuel cracking, crack closure, porosity decrease, and the temperature dependence of fuel creep through the course of the transient. Modeling emphasis has been placed on results obtained from Fuel Cladding Transient Test (FCTT) testing, Transient Fuel Deformation (TFD) tests and TREAT integral fuel pin experiments

Wire-wrapped rod-bundle heat-transfer analysis for LMFBR

International Nuclear Information System (INIS)

Wong, C.N.C.; Todreas, N.E.

1982-07-01

Helical wire wraps are widely used in the LMFBR fuel and blanket assemblies to provide coolant mixing and maintain proper spacing between fuel pins. The presence of the helical wire, however, may possibly induce heat transfer problems, such as the uncertainty of the maximum clad temperature as a result of the contact between the wires and the pins. In this study, the detailed transient three dimensional velocity and temperature distributions for the coolant around the pin will be determined by solving the governing momentum and energy equation numerically. A computer code HEATRAN has been developed to perform this calculation. Before the computer code HEATRAN is applied to the wire wrapped rod bundle problem, it is used to analyze a wide range of fluid and heat transfer problem to verify its capabilities

Performance of refractory alloy-clad fuel pins

International Nuclear Information System (INIS)

Dutt, D.S.; Cox, C.M.; Millhollen, M.K.

1984-12-01

This paper discusses objectives and basic design of two fuel-cladding tests being conducted in support of SP-100 technology development. Two of the current space nuclear power concepts use conventional pin type designs, where a coolant removes the heat from the core and transports it to an out-of-core energy conversion system. An extensive irradiation testing program was conducted in the 1950's and 1960's to develop fuel pins for space nuclear reactors. The program emphasized refractory metal clad uranium nitride (UN), uranium carbide (UC), uranium oxide (UO 2 ), and metal matrix fuels (UCZr and BeO-UO 2 ). Based on this earlier work, studies presented here show that UN and UO 2 fuels in conjunction with several refractory metal cladding materials demonstrated high potential for meeting space reactor requirements and that UC could serve as an alternative but higher risk fuel

Cladding properties under simulated fuel pin transients

International Nuclear Information System (INIS)

Hunter, C.W.; Johnson, G.D.

1975-01-01

A description is given of the HEDL fuel pin testing program utilizing a recently developed Fuel Cladding Transient Tester (FCTT) to generate the requisite mechanical property information on irradiated and unirradiated fast reactor fuel cladding under temperature ramp conditions. The test procedure is described, and data are presented

Finite element modelling of different CANDU fuel bundle types in various refuelling conditions

International Nuclear Information System (INIS)

Roman, M. R.; Ionescu, D. V.; Olteanu, G.; Florea, S.; Radut, A. C.

2016-01-01

The objective of this paper is to develop a finite element model for static strength analysis of the CANDU standard with 37 elements fuel bundle and the SEU43 with 43 elements fuel bundle design for various refuelling conditions. The computer code, ANSYS7.1, is used to simulate the axial compression in CANDU type fuel bundles subject to hydraulic drag loads, deflection of fuel elements, stresses and displacements in the end plates. Two possible situations for the fuelling machine side stops are considered in our analyses, as follows: the last fuel bundle is supported by the two side stops and a side stop can be blocked therefore, the last fuel bundle is supported by only one side stop. The results of the analyses performed are briefly presented and also illustrated in a graphical form. The finite element model developed in present study is verified against test results for endplate displacement and element bowing obtained from strength tests with fuel bundle string and fuelling machine side-stop simulators. Comparison of ANSYS model predictions with these experimental results led to a very good agreement. Despite the difference in hydraulic load between SEU43 and CANDU standard fuel bundles strings, the maximum stress in the SEU43 endplate is about the same with the maximum stress in the CANDU standard endplate. The comparative assessment reveals that SEU43 fuel bundle is able to withstand high flow rate without showing a significant geometric instability. (authors)

Radial power distribution shaping within a PWR fuel assembly utilizing asymmetrically loaded gadolinia-bearing fuel pins

International Nuclear Information System (INIS)

Stone, I.Z.

1992-01-01

As in-core fuel management designs evolve to meet the demands of increasing energy output, more innovative methods are developed to maintain power peaking within acceptable thermal margin limits. In-core fuel management staff must utilize various loading pattern strategies such as cross-core movement of fuel assemblies, multibatch enrichment schemes, and burnable absorbers as the primary means of controlling the radial power distribution. The utilization of fresh asymmetrically loaded gadolinia-bearing assemblies as a fuel management tool provides an additional means of controlling the radial power distribution. At Siemens Nuclear Power Corporation (SNP), fresh fuel assemblies fabricated with asymmetrically loaded gadolinia-bearing fuel rods have been used successfully for several cycles of reactor operation. Asymmetric assemblies are neutronically modeled using the same tools and models that SNP uses to model symmetrically loaded gadolinia-bearing fuel assemblies. The CASMO-2E code is used to produce the homogenized macroscopic assembly cross sections for the nodal core simulator. Optimum fuel pin locations within the asymmetrical assembly are determined using the pin-by-pin PDQ7 assembly core model for each new assembly design. The optimum pin location is determined by the rod loading that minimizes the peak-to-average pin power

Effects of variations in fuel pellet composition and size on mixed-oxide fuel pin performance

International Nuclear Information System (INIS)

Makenas, B.J.; Jensen, B.W.; Baker, R.B.

1980-10-01

Experiments have been conducted which assess the effects on fuel pin performance of specific minor variations from nominal in both fuel pellet size and pellet composition. Such pellets are generally referred to in the literature as rogue pellets. The effect of these rogue pellets on fuel pin and reactor performance is shown to be minimal

A device for tracking-down the defective fuel rods in a reactor

International Nuclear Information System (INIS)

Preda, Marin; Ciocanescu, Marin; Barbos, Dumitru; Rogociu, Ioan

2008-01-01

The paper gives first the fuel element description and its operation. If a cladding defect arises, some of the fission isotopes pass into the primary cooling system and, as these isotopes are extremely radio-active, the danger of primary cooling system contamination occurs what entails expensive decontamination operations. For identification of the bundle containing the defective pins a simple, modular device was designed and made. It works by pointing-out the bundle(s) which has at least one defective fuel pin. After tracking, the fuel bundle is picked-up from the core and searching is continued to point-out the defective pin inside post-irradiation-hot cells. For dosimetric survey in the reactor hall, an aerosol detector was used. When an accident arises the released noble gases will be detected by this detector. The detector can give no information where the damage is located for one of the fuel pins inside the irradiation devices (loop or capsule) can also get defective and consequently it can release radioactive noble gases in the reactor hall. For avoiding this a radioactive survey device for core cooling agent was mounted by the primary cooling system. The device for defective fuel rod identification in the nuclear reactor is composed of the following components: - a device for water sampling from the fuel bundle; - a suction valve; - a handling tool; - an electric pump; - ionic filters; - a flexible hose. When fission isotopes arise in primary cooling system, the device is brought to the edge of the reactor pool in a sharp positioning. By means of the handling tool the sampling device is inserted at the top of the fuel bundle. The suction inlet circuit and the electric pump are filled with pool water, and after that the ionic filter and outlet circuit are filled also. The electric pump is actuated and the following circuit is operated: fuel bundle, electric pump, ionic filter, pool. For avoiding the overheating of the pump, part of the flow is by

Fuel bundle movement due to reverse flow

Energy Technology Data Exchange (ETDEWEB)

Wahba, N N; Akalin, O [Ontario Hydro, Toronto, ON (Canada)

1996-12-31

When a break occurs in the inlet feeder or inlet header, the rapid depressurization will cause the channel flow to reverse forcing the string of bundles to accelerate and impact with upstream shield plug. A model has been developed to predict the bundle motion due to the channel flow reversal. The model accounts for various forces acting on the bundle. A series of five reverse flow, bundle acceleration experiments have been conducted simulating a break in the inlet feeder of a CANDU fuel channel. The model has been validated against the experiments. The predicted impact velocities are in good agreement with the measured values. It is demonstrated that the model may be successfully used in predicting bundle relocation timing following a large LOCA (loss of coolant). (author). 7 refs., 3 tabs., 11 figs.

Nuclear fuel pin

International Nuclear Information System (INIS)

Hartley, Kenneth; Moulding, T.L.J.; Rostron, Norman.

1979-01-01

Fuel pin for use in fast breeder nuclear reactors containing fissile and fertile areas of which the fissile and fertile materials do not mix. The fissile material takes the shape of large and small diameter microspheres (the small diameter microspheres can pass through the interstices between the large microspheres). The barrier layers being composed of microspheres with a diameter situated between those of the large and small microspheres ensure that the materials do not mix [fr

Automation of FBTR fuel pin inspection using FPGA

International Nuclear Information System (INIS)

Khare, K.M.; Pai, Siddhesh; Pant, Brijesh; Sendhil Raja, S.; Gupta, P.K.

2011-01-01

A non-contact metrology system for inspection of FBTR fuel pins has been developed. The system consists of a stepper motors driven mechanism for orientation and positioning of FBTR fuel pin, a telecentric imaging system, absolute linear encoder with 0.1 μm resolution and a Field Programmable Gate Array (FPCA) based controller. The FBTR pin assembly is telecentrically illuminated from bottom by a red LED and its shadow graph is imaged using a CCD camera through telecentric imaging lens system. For system control and automation we have used a FPGA that has integrated soft picoblaze processor, X-θ axis motion controller, custom IPs for encoder data acquisition, synchronization circuit, RS485 interface along with other l/Os. Using the Graphical User Interface (GUI) on a PC the system is initialized at home position and the controller provides the trigger signal for start of data acquisition of CCD camera. CCD image of pin and the corresponding X-θ information is captured. After the acquisition of one set of images, the imaging module is moved with a step size pre-programmed to ensure proper stitching of acquired images. The GUI is programmed to analyze these X-θ Images to calculate the required parameters of the fuel pin like the diameter variation, pitch and bow. The details of the instrument and measurements made with it will be presented. (author)

Nuclear fuel assembly

International Nuclear Information System (INIS)

Delafosse, Jacques.

1977-01-01

This invention relates to a nuclear fuel assembly for a light or heavy water reactor, or for a fast reactor of the kind with a bundle of cladded pins, maintained parallel to each other in a regular network by an assembly of separate supporting grids, fitted with elastic bearing surfaces on these pins [fr

Power release estimation inside of a fuel pin neighbouring a WWER-440 control rod

International Nuclear Information System (INIS)

Mikus, J.

2006-01-01

This work presents an estimation of the control rod (CR) influence in the WWER-440 core on the power release inside of a fuel pin neighbouring CR, that can have some consequences due to possible static and cyclic loads, for example fuel pin / fuel assembly bowing. For this purpose detailed (usual) axial power distribution measurements were performed in a WWER-440 type core on the light water, zero-power research reactor LR-0 in fuel pins near to an authentic CR model at zero boron concentration in moderator, modelling the conditions at the end of fuel cycle. To demonstrate the CR influence on power distribution inside of one fuel pin neighbouring CR, results of above measurements were used for estimation of the: 1) Axial power distribution inside of the investigated fuel pin in both opposite positions on its pellets surface that are situated to- and outwards CR and corresponding gradient of the (r, z) - power distribution in above opposite positions and 2) Azimuthal power distributions on pellet surface of the investigated fuel pin in horizontal planes at selected axial coordinates. Similar information can be relevant from the viewpoint of the fuel pin failures occurrence investigation

Fuel or irradiation subassembly

International Nuclear Information System (INIS)

Seim, O.S.; Hutter, E.

1975-01-01

A subassembly for use in a nuclear reactor is described which incorporates a loose bundle of fuel or irradiation pins enclosed within an inner tube which in turn is enclosed within an outer coolant tube and includes a locking comb consisting of a head extending through one side of the inner sleeve and a plurality of teeth which extend through the other side of the inner sleeve while engaging annular undercut portions in the bottom portion of the fuel or irradiation pins to prevent movement of the pins

Equations of motion for two-phase flow in a pin bundle of a nuclear reactor

International Nuclear Information System (INIS)

Chawla, T.C.; Ishii, M.

1978-01-01

By performing Eulerian area averaging over a channel area of the local continuity, momentum, and energy equations for single phase turbulent flow and assuming each phase in two-phase flows to be continuum but coupled by the appropriate 'jump' conditions at the interface, the corresponding axial macroscopic balances for two-fluid model in a pin bundle are obtained. To determine the crossflow, a momentum equation in transverse (to the gap between the pins) direction is obtained for each phase by carrying out Eulerian segment averaging of the local momentum equation, where the segment is taken parallel to the gap. By considering the mixture as a whole, a diffusion model based on drift-flux velocity is formulated. In the axial direction it is expressed in terms of three mixture conservation equations of mass, momentum, and energy with one additional continuity equation for the vapor phase. For the determination of crossflow, transverse momentum equation for a mixture is obtained. It is considered that the previous formulation of the two-phase flow based on the 'slip' flow model and the integral subchannel balances using finite control volumes is inadequate in that the model is heuristic and, a priori, assumes the order of magnitude of the terms, also the model is incomplete and incorrect when applied to two-phase mixtures in thermal non-equilibrium such as during accidental depressurization of a water cooled reactor. The governing equations presented are shown to be a very formal and sound physical basis and are indispensable for physically correct methods of analyzing two-phase flows in a pin bundle. (author)

Reirradiation of mixed-oxide fuel pins at increased temperatures

International Nuclear Information System (INIS)

Lawrence, L.A.; Weber, E.T.

1976-05-01

Mixed-oxide fuel pins from EBR-II irradiations were reirradiated in the General Electric Test Reactor (GETR) at higher temperatures than experienced in EBR-II to study effects of the increased operating temperatures on thermal/mechanical and chemical behavior. The response of a mixed-oxide fuel pin to a power increase after having operated at a lower power for a significant portion of its life-time is an area of performance evaluation where little information currently exists. Results show that the cladding diameter changes resulting from the reirradiation are strongly dependent upon both prior burnup level and the magnitude of the temperature increase. Results provide the initial rough outlines of boundaries within which mixed-oxide fuel pins can or cannot tolerate power increases after substantial prior burnup at lower powers

Device for supporting a fuel pin cluster within a nuclear reactor fuel assembly wrapper

International Nuclear Information System (INIS)

Marmonier, P.; Mesnage, B.; Teulon, J.; Vayra, J.; Venobre, H.

1976-01-01

A supporting member for an array of parallel rails each carrying one row of slidably mounted pins of a fuel cluster is placed coaxially at the lower end of a vertical fuel assembly wrapper. Each parallel rail is provided at each end with a downward extension and terminal lug which engages in a lateral groove formed in the periphery of the supporting member in order to lock and maintain the rails and the fuel pins in uniformly spaced relation within the fuel assembly wrapper. 10 claims, 8 figures

TRANSPA: a code for transient thermal analysis of a single fuel pin

International Nuclear Information System (INIS)

Prenger, F.C.

1985-02-01

An analytical model (TRANSPA) for the transient thermal analysis of a single uranium carbide fuel pin was developed. This model uses thermal boundary conditions obtained from COBRA-WC output and calculates the transient thermal response of a single fuel pin to changes in internal power generation, coolant flowrate, or fuel pin physical configuration. The model uses the MITAS finite difference thermal analyzer. MITAS provides the means to input separate conductance models through the use of a user subroutine input capability. The model is a lumped-mass representation of the fuel pin using 26 nodes and 42 conductors. Run time for each transient analysis is approximately one minute of central processor time on the NOS operating system

Fuel pin failure in the PFR/TREAT experiments

International Nuclear Information System (INIS)

Herbert, R.; Hunter, C.W.; Kramer, J.M.; Wood, M.H.; Wright, A.E.

1986-01-01

The PFR/TREAT safety testing programme involves the transient testing of fresh and pre-irradiated UK and US fuel pins. This paper summarizes the experimental and calculational results obtained to date on fuel pin failure during transient overpower (resulting from an accidental addition of resolivity) and transient undercooling followed by overpower (arising from an accidental stoppage of the primary sodium circulating pumps) accidents. Companion papers at this conference address: (I) the progress and future plans of the programme, and (II) post-failure material movements

Serviceability of rod ceramic fuel pins on motoring conditions of FTP or NEMF reactor

International Nuclear Information System (INIS)

Deryavko, I.I.

2004-01-01

The operation conditions of rod ceramic fuel pins in the running hydrogen-cooled technological canals of FTP or NEMF reactor on the motoring conditions are considered. The available postreactor researches of the fuel pins are presented and the additional postreactor researches of fuel pins, tested on this mode in IVG.1 and IRGIT reactors, are carried out. The fuel pins serviceability on motoring conditions of FTP or NEF reactor operation is concluded. (author)

Fuel pin response to an overpower transient in an LMFBR

International Nuclear Information System (INIS)

Grosberg, A.J.; Head, J.L.

1979-01-01

This paper describes a method by which the ability of a whole-core code accurately to predict the time and location of the first fuel pin failures may be tested. The method involves the use of a relatively simple whole-core code to 'drive' a sophisticated fuel pin code, which is far too complex to be used within a whole-core code but which is potentially capable of modelling reliably the response of an individual fuel pin. The method cannot follow accurately the subsequent course of the transient because the simple whole-core code does not model the reactivity effects of events which may follow pin failure. The codes used were the simple whole-core code FUTURE and the fuel pin behaviour code FRUMP. The paper describes an application of the method to analyse a hypothetical LMFBR accident in which the control rods were assumed to be driven from the core at maximum speed, with all trip circuits failed. Taking 0.5% clad strain as a clad failure criterion, failure was predicted to occur at the top of the active core at about 10s into the transient. A repeat analysis, using an alternative clad yield criterion which is thought to be more realistic, indicated failure at the same position but 24s into the transient. This is after the onset of sodium boiling. Pin failure at the top of the core are likely to cause negative reactivity changes. In this hypothetical accident, pin failures are likely, therefore, to have a moderating effect on the course of the transient. (orig.)

TACO: fuel pin performance analysis

International Nuclear Information System (INIS)

Stoudt, R.H.; Buchanan, D.T.; Buescher, B.J.; Losh, L.L.; Wilson, H.W.; Henningson, P.J.

1977-08-01

The thermal performance of fuel in an LWR during its operational lifetime must be described for LOCA analysis as well as for other safety analyses. The determination of stored energy in the LOCA analysis, for example, requires a conservative fuel pin thermal performance model that is capable of calculating fuel and cladding behavior, including the gap conductance between the fuel and cladding, as a function of burnup. The determination of parameters that affect the fuel and cladding performance, such as fuel densification, fission gas release, cladding dimensional changes, fuel relocation, and thermal expansion, should be accounted for in the model. Babcock and Wilcox (B and W) has submitted a topical report, BAW-10087P, December 1975, which describes their thermal performance model TACO. A summary of the elements that comprise the TACO model and an evaluation are presented

Analysis of fuel handling system for fuel bundle safety during station blackout in 500 MWe PHWR unit of India

International Nuclear Information System (INIS)

Madhuresh, R.; Nagarajan, R.; Jit, I.; Sanatkumar, A.

1996-01-01

Situations of Station Blackout (SBO) i.e. postulated concurrent unavailability of Class Ill and Class IV power, could arise for a long period, while on-power refuelling or other fuel handling operations are in progress with the hot irradiated fuel bundles being anywhere in the system from the Reactor Building to the Spent Fuel Storage Bay. The cooling provisions for these fuel bundles are diverse and specific to the various stages of fuel handling operations and are either on Class Ill or on Class II power with particular requirements of instrument air. Therefore, during SBO, due to the limited availability of Class II power and instrument air, it becomes difficult to maintain cooling to these fuel bundles. However, some minimal cooling is essential, to ensure the safety of the bundles. As discussed in the paper, safety of these fuel bundles in the system and/or for those lying in the liner tube region of the reactor end fitting is ensured, during SBO, by resorting to passive means like 'stay-put', 'gravity- fill', 'D 2 0- steaming' etc. for cooling the bundles. The paper also describes various consequences emanating from these cooling schemes. (author). 6 refs., 2 tabs., 8 figs

Fuel bundle to pressure tube fretting in Bruce and Darlington

Energy Technology Data Exchange (ETDEWEB)

Norsworthy, A G; Ditschun, A [Atomic Energy of Canada Ltd., Mississauga, ON (Canada)

1996-12-31

As the fuel channel elongates due to creep, the fuel string moves relative to the inlet until the fuel pads at the inboard end eventually separate from the spacer sleeve, and the fuel resides on the burnish mark of the pressure tube. The bundle is then supported in a fashion which contributes to increased levels of vibration. Those pads which (due to geometric variation) have contact loads with the pressure tube within a certain range, vibrate, and cause significant fretting on the burnish mark, and further along at the midplane of the bundle. Inspection of the pressure tubes in Bruce A, Bruce B, and Darlington has revealed fret damage up to 0.55 mm at the burnish mark and slightly lower than this at the inlet bundle midplane. To date, all fret marks have been dealt with successfully without the need for tube replacement, but a program of work has been initiated to understand the mechanism and reduce the fretting. Such understanding is necessary to guide future design changes to the fuel bundle, to guide future inspection programs, to guide maintenance programs, and for longer term strategic planning. This paper discusses how the understanding of fretting has evolved and outlines a current hypothesis for the mechanism of fretting. The role of bundle geometry, excitation forces, and reactor conditions are reviewed, along with options under consideration to mitigate damage. (author). 4 refs., 2 tabs., 13 figs.

Fuel bundle to pressure tube fretting in Bruce and Darlington

International Nuclear Information System (INIS)

Norsworthy, A.G.; Ditschun, A.

1995-01-01

As the fuel channel elongates due to creep, the fuel string moves relative to the inlet until the fuel pads at the inboard end eventually separate from the spacer sleeve, and the fuel resides on the burnish mark of the pressure tube. The bundle is then supported in a fashion which contributes to increased levels of vibration. Those pads which (due to geometric variation) have contact loads with the pressure tube within a certain range, vibrate, and cause significant fretting on the burnish mark, and further along at the midplane of the bundle. Inspection of the pressure tubes in Bruce A, Bruce B, and Darlington has revealed fret damage up to 0.55 mm at the burnish mark and slightly lower than this at the inlet bundle midplane. To date, all fret marks have been dealt with successfully without the need for tube replacement, but a program of work has been initiated to understand the mechanism and reduce the fretting. Such understanding is necessary to guide future design changes to the fuel bundle, to guide future inspection programs, to guide maintenance programs, and for longer term strategic planning. This paper discusses how the understanding of fretting has evolved and outlines a current hypothesis for the mechanism of fretting. The role of bundle geometry, excitation forces, and reactor conditions are reviewed, along with options under consideration to mitigate damage. (author). 4 refs., 2 tabs., 13 figs

Method and device for cleaning fuel pins

International Nuclear Information System (INIS)

Matsumoto, Kaname; Oohigashi, Yoshiaki.

1985-01-01

Purpose: To remove clads or scales deposited on the outer surface of fuel pins in BWR type reactors. Method: A fuel assembly taken out of a reactor core is vertically contained without detaching a channel box in a scrubber tower disposed in a liquid tight manner within a fuel pool. Then, a specifically prepared slurry is caused to flow and uprise from the bottom of the scrubber tower into the channel box and then discharged from the top of the tower. The slurry is prepared by mixing pure water and granules (for example, as activated carbon, ion exchanger resin, iron and molecular sieve) of such a granular size as not causing clogging in the channel box of the fuel assembly and having a larger specific gravity than pure water. The slurry flown into the channel box scrubs the surface of fuel pins to scrape off clads or scales. Then, discharged slurry is sent to a hydraulic cyclone to separate the granules from the clads or scales. (Ikeda, J.)

Assessment of clad integrity of PHWR fuel pin following a postulated severe accident

International Nuclear Information System (INIS)

Dutta, B.K.; Kushwaha, H.S.; Venkat Raj, V.

2000-01-01

A mechanistic fuel performance analysis code FAIR has been developed. The code can analyse fuel pins with free standing as well as collapsible clad under normal, off-normal and accident conditions of reactors. The code FAIR is capable of analysing the effects of high burnup on fuel behaviour. The code incorporates finite element based thermo-mechanical module for computing transient temperature distribution and thermal-elastic-plastic stresses in the fuel pin. A number of high temperature thermo-physical and thermo-mechanical models also have been incorporated for analysing fuel pins subjected to severe accident scenario. The present paper describes salient features of code FAIR and assessment of clad integrity of PHWR fuel pins with different initial burnup subjected to severe accident scenario. (author)

Thermal-Hydraulic Simulations of Single Pin and Assembly Sector for IVG- 1M Reactor

Energy Technology Data Exchange (ETDEWEB)

Kraus, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Garner, P. [Argonne National Lab. (ANL), Argonne, IL (United States); Hanan, N. [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-01-15

Thermal-hydraulic simulations have been performed using computational fluid dynamics (CFD) for the highly-enriched uranium (HEU) design of the IVG.1M reactor at the Institute of Atomic Energy (IAE) at the National Nuclear Center (NNC) in the Republic of Kazakhstan. Steady-state simulations were performed for both types of fuel assembly (FA), i.e. the FA in rows 1 & 2 and the FA in row 3, as well as for single pins in those FA (600 mm and 800 mm pins). Both single pin calculations and bundle sectors have been simulated for the most conservative operating conditions corresponding to the 10 MW output power, which corresponds to a pin unit cell Reynolds number of only about 7500. Simulations were performed using the commercial code STAR-CCM+ for the actual twisted pin geometry as well as a straight-pin approximation. Various Reynolds-Averaged Navier-Stokes (RANS) turbulence models gave different results, and so some validation runs with a higher-fidelity Large Eddy Simulation (LES) code were performed given the lack of experimental data. These singled out the Realizable Two-Layer k-ε as the most accurate turbulence model for estimating surface temperature. Single-pin results for the twisted case, based on the average flow rate per pin and peak pin power, were conservative for peak clad surface temperature compared to the bundle results. Also the straight-pin calculations were conservative as compared to the twisted pin simulations, as expected, but the single-pin straight case was not always conservative with regard to the straight-pin bundle. This was due to the straight-pin temperature distribution being strongly influenced by the pin orientation, particularly near the outer boundary. The straight-pin case also predicted the peak temperature to be in a different location than the twisted-pin case. This is a limitation of the straight-pin approach. The peak temperature pin was in a different location from the peak power pin in every case simulated, and occurred at an

Progress in fuel-motion-diagnostics instrumentation evaluation at Parka

International Nuclear Information System (INIS)

Evans, A.E. Jr.; Orndoff, J.D.

1979-01-01

Hodoscope neutron and gamma-ray imaging of bundles containing from 1 to 127 pins have been studied. Ability to image a single missing pin from assemblies of up to 127 pins has been established. The image of a single-pin void in a test assembly was found to vary with the depth of the void in the assembly, for both 37-pin and 127-pin bundles. The degree to which a thick steel test casing will impede image quality has been studied. A 21-mm-thick casing was found to reduce the sensitivity of fast-neutron hodoscope images to fuel defects by 30% and of gamma-ray images by 50%. 9 refs

Reactor physics assessment of modified 37-element CANDU fuel bundles

International Nuclear Information System (INIS)

Pristavu, R.; Rizoiu, A.

2016-01-01

Reducing the central element diameter in order to improve the total flow area of CANDU fuel bundle and redistribute the power density of all remaining elements was studied in Canada and Korea when considering the effect of aging pressure tube diametral creep. The aim of this paper is to study the modified bundle behavior using the transport codes WIMS and DRAGON. In calculations, a WIMS nuclear data library on 172 energy groups was used. 2-D transport calculations were performed with WIMS and DRAGON, leading to similar results in estimated cell parameters. Additionally, 3-D DRAGON calculations were carried on in order to evaluate the local flux distribution shift, as well as the incremental cross sections for supercells containing modified CANDU bundles and reactivity devices. The overall effect of using modified fuel bundles was meaningless for both cell and supercell parameters, thus ensuring this possibility of fuel improvement for thermal-hydraulic purposes only. (authors)

Potential of high speed x-ray cinematography as a fuel motion diagnostic for safety test facilities

International Nuclear Information System (INIS)

Stalker, K.T.; Choate, L.M.; Posey, L.D.

1979-01-01

Experiments have been performed which indicate the feasibility of using X-ray cinematography as a diagnostic tool for monitoring fuel motion in large pin bundle advanced reactor safety tests. This capability was demonstrated by imaging motion in a 37-pin bundle of simulated fuel elements at a data rate of 400 pictures per second using an active detector system coupled with a 10 MeV accelerator. 5 refs

Out-of-pile bundle temperature escalation under severe fuel damage conditions

International Nuclear Information System (INIS)

Hagen, S.; Peck, S.O.

1983-08-01

This report provides an overview of the test conduct, results, and posttest appearance of bundle test ESBU-1. The purpose of the test was to investigate fuel rod temperature escalation due to the exothermal zircaloy/steam reaction in a bundle geometry. The 3x3 bundle was surrounded by a zircaloy shroud and 6 mm of fiber ceramic insulation. The center rod escalated to a maximum of 2,250 0 C. Runoff of the melt apparently limited the escalation. Posttest visual examination of the bundle showed that cladding from every rod had melted, liquefied some fuel, flowed down the rod, and frozen in a solid mass that substantially blocked all flow channels. A large amount of powdery rubble, probably fuel that fractured during cooldown, was found on top of the blockage. Metallographic, EMP, and SEM examinations showed that the melt had dissolved both fuel and oxidized cladding, and had itself been oxidized by steam. (orig.) [de

Analyses of deformation and thermal-hydraulics within a wire-wrapped fuel subassembly in a liquid metal fast reactor by the coupled code system

Energy Technology Data Exchange (ETDEWEB)

Uwaba, Tomoyuki, E-mail: uwaba.tomoyuki@jaea.go.jp; Ohshima, Hiroyuki; Ito, Masahiro

2017-06-15

Highlights: • The coupled computational code system allowed for mechanical and thermal-hydraulic analyses in a fast reactor fuel subassembly. • In this system interactive calculations between flow area deformations and coolant temperature changes are repeated to their convergence state. • Effects on bundle-duct interaction on coolant temperature distributions were investigated by using the code system. - Abstract: The coupled numerical analysis of mechanical and thermal-hydraulic behaviors was performed for a wire-wrapped fuel pin bundle subassembly irradiated in a fast reactor. For the analysis, the fuel pin bundle deformation analysis code BAMBOO and the thermal-hydraulic analysis code ASFRE exchanged the deformation and temperature analysis results through the iterative calculations to attain convergence corresponding to the static balance between deformation and temperature. The analysis by the coupled code system showed that the radial distribution of coolant temperature in the subassembly tended to flatten as a result of the fuel pin bundle deformation governed by cladding void swelling and irradiation creep. Such flattening of temperature distribution was slightly observed as a result of fuel pin bowings due to the cladding-wire interaction even when no bundle-duct interaction occurred. The effect of the spacer wire-pitch on deformation and thermal-hydraulics was also investigated in this study.

Verification of the CASMO-3/SIMULATE-3 pin power accuracy by comparison with operating boiling water reactor measurements

International Nuclear Information System (INIS)

Uegata, T.; Saji, E.; Tanaka, H.

1993-01-01

Intranodal pin power distributions calculated by the CASMO-3/SIMULATE-3 code have been compared with pin gamma scan measurements. These data were obtained from the depleted core of an operating boiling water reactor (BWR), which is more complicated than a pressurized water reactor to calculate because of the existence of coolant void distributions and cruciform control blades. Furthermore, measured bundles include mixed-oxide (MOX) bundles in which steep thermal flux gradients occur. Both UO 2 and MOX bundles have been calculated in the same manner based on the standard CASMO-3/SIMULATE-3 methods. The total pin power root-mean-square (rms) error is 2.7%, which includes measurement error, from an 896-point comparison. There is no obvious dependency on axial elevations (void fractions) and no significant difference between fuel types (UO 2 or MOX), although the errors in a peripheral bundle, which is less important from the standpoint of core design, are somewhat larger than those in the internal bundles. If the peripheral bundle is excluded, the total rms error is reduced to 2.2%. From these results, it is concluded that excellent agreement has been obtained between the calculations and measurements and that the calculational capability of CASMO-3/SIMULATE-3 for the intranodal pin power distribution is quite satisfactory and useful for BWR core design

Improving the neutronic characteristics of a boiling water reactor by using uranium zirconium hydride fuel instead of uranium dioxide fuel

Energy Technology Data Exchange (ETDEWEB)

Galahom, Ahmed Abdelghafar [Higher Technological Institute, Ramadan (Egypt)

2016-06-15

The present work discusses two different models of boiling water reactor (BWR) bundle to compare the neutronic characteristics of uranium dioxide (UO{sub 2}) and uranium zirconium hydride (UZrH{sub 1.6}) fuel. Each bundle consists of four assemblies. The BWR assembly fueled with UO{sub 2} contains 8 × 8 fuel rods while that fueled with UZrH{sub 1.6} contains 9 × 9 fuel rods. The Monte Carlo N-Particle Transport code, based on the Mont Carlo method, is used to design three dimensional models for BWR fuel bundles at typical operating temperatures and pressure conditions. These models are used to determine the multiplication factor, pin-by-pin power distribution, axial power distribution, thermal neutron flux distribution, and axial thermal neutron flux. The moderator and coolant (water) are permitted to boil within the BWR core forming steam bubbles, so it is important to calculate the reactivity effect of voiding at different values. It is found that the hydride fuel bundle design can be simplified by eliminating water rods and replacing the control blade with control rods. UZrH{sub 1.6} fuel improves the performance of the BWR in different ways such as increasing the energy extracted per fuel assembly, reducing the uranium ore, and reducing the plutonium accumulated in the BWR through burnup.

Some observations on pitting corrosion in the zircaloy cladding of fuel pins irradiated in a PWR loop

International Nuclear Information System (INIS)

Linde, A. van der; Letsch, A.C.; Hornsveld, E.M.

1978-11-01

A three-pins, zircaloy-4 clad, sphere-pac bundle was irradiated in a 280 0 C PWR loop in the HFR at Petten during 131 effective full power days to a bundle average burnup of 0.84 % FIMA. The pins contained a mixture of 61.5 w/o of 1050 μm (U,Pu) 0 2 spheres, 18.5 w/o of 115 μm UO 2 spheres and 20.0 w/o of 2 spheres. The as-fabricated smear density of the vibratory compacted mixture was 81-85 % T.D. The pressure of the pin filling gas was 1 bar helium for pin 306 and 25 bar helium for the pins 308 and 309. The cladding was zircaloy-4 tubing, stress relieved for 4 hours at 540 0 C, with an inner diameter of 9.30 mm and a wall thickness of 0.73 mm. Exposure of the pins in the loop started in the as-pickled, degreased surface condition. The pins operated at an average heat rating of 335 W/cm and at a peak rating of 620 W/cm. The end-of -life peak rating was 425 W/cm. Unfavourable water chemistry conditions of the coolant during the last weeks of the irradition, in particular low NH 3 concentrations resulting in low pH values, caused the deposition of heavy crud layers on the pin surfaces. This crud layer caused a small cladding defect in pin 306 at the axial position of the peak heat rating. The zircaloy-4 wall failed by complete oxidation, which started at and progressed from the outer, coolant side, surface. Immediately after the detection of fission product activity in the loop water, the irradiation of the bundle was terminated. Microscopic investigations on cross sections of the pins 306 and 309 revealed the presence of oxide pits at the outer surface of the zircalloy-4 wall

Beginning-of-life gap closure behaviour of experimental PFBR MOX fuel pin

International Nuclear Information System (INIS)

Jayaraj, V.V.; Padalakshmi, M.; Ojha, B.K.; Padma Prabu, C.; Saravanan, T.; Venkiteswaran, C.N.; Philip, John; Muralidharan, N.G.; Joseph, Jojo; Kasiviswanathan, K.V.; Jayakumar, T.

2011-01-01

Mixed oxide fuel with 22 % and 29% plutonium is chosen as the fuel for PFBR for the two fissile zones. Due to the fabrication tolerances in the pellet diameter, fuel has to be preconditioned at a lower linear power for a brief period before raising the power to the rated value of 450 W/cm. PIE was done on an experimental MOX fuel pin irradiated in FBTR for 13 days at a linear power of 400 W/cm for gap closure studies with the objective of optimising the duration of pre-conditioning before raising the power to the design value of 450 W/cm. X-radiography and remote metallography was done on the fuel pin to estimate the axial fuel column elongation and fuel-clad gap. Remote metallography of the fuel pin cross-sections at five axial locations of the fuel column and the subsequent fuel-clad gap measurement has indicated that the average radial gap has reduced from the pre-irradiation value of 75-110 microns to around 12-13 microns along the entire length of the fuel column. This paper will describe the details of examinations and results of the PIE carried out on the MOX fuel pin. (author)

Analysis of fuel handling system for fuel bundle safety during station blackout in 500 MWe PHWR unit of India

Energy Technology Data Exchange (ETDEWEB)

Madhuresh, R; Nagarajan, R; Jit, I; Sanatkumar, A [Nuclear Power Corporation of India Ltd., Mumbai (India)

1997-12-31

Situations of Station Blackout (SBO) i.e. postulated concurrent unavailability of Class Ill and Class IV power, could arise for a long period, while on-power refuelling or other fuel handling operations are in progress with the hot irradiated fuel bundles being anywhere in the system from the Reactor Building to the Spent Fuel Storage Bay. The cooling provisions for these fuel bundles are diverse and specific to the various stages of fuel handling operations and are either on Class Ill or on Class II power with particular requirements of instrument air. Therefore, during SBO, due to the limited availability of Class II power and instrument air, it becomes difficult to maintain cooling to these fuel bundles. However, some minimal cooling is essential, to ensure the safety of the bundles. As discussed in the paper, safety of these fuel bundles in the system and/or for those lying in the liner tube region of the reactor end fitting is ensured, during SBO, by resorting to passive means like `stay-put`, `gravity- fill`, `D{sub 2}0- steaming` etc. for cooling the bundles. The paper also describes various consequences emanating from these cooling schemes. (author). 6 refs., 2 tabs., 8 figs.

One- and two-dimension effects on fuel pin lifetime

International Nuclear Information System (INIS)

Stephen, J.D.; Biancheria, A.; Leibnitz, D.; O'Reilly, B.D.; Liu, Y.Y.; Labar, M.P.; Gneiting, B.C.

1979-01-01

Lifetime, or breach of the cladding, is a difficult performance limit to establish in fuel pin design. The significant benefits of high plant capacity factor favor conservative design to eliminate downtime or partial power operation caused by the breach limit; however, overly conservative design produces significant penalties. The LIFE system is being applied to help understand the range between operation and breach so that appropriate design margins can be selected. Standards are being developed in the USA to assure the structural integrity of all core components. These standards will provide guidelines to account for the failure mechanisms observed in the high temperature, high fluence core environment. The work to date indicates that creep rupture is the most important failure mechanism for mixed-oxide fuel pins during normal operation and slow power changes. The local cumulative creep rupture damage fraction (CDF) has been adopted as the parameter to assess the approach to failure. Several oxide breached pins and siblings have been studied For example, the P23B-73 pin was an FFTR driver design pin irradiated in EBR-II which failed at 10 at,% burnup. Initial evaluation based on LIFE3 led to the conclusion that the pin should not have failed. Further analyses determined the sensitivity of the breach prediction to the time-to-rupture correlation, cladding temperature, and fuel-fission product swelling (which had not been modeled in LIFE3). The uncertainties in the time-to-rupture correlation have been established. But LIFE is a one-dimensional model. The TWOD code is complete, and development of the best way to couple LIFE and TWOD for lifetime analysis is in progress. Two preliminary conclusions from analysis of representative oxide pin geometries are, first, that the circumferential stress distribution may not peak at the hot spot, but the damage (CDF) does. And second, that the effect of stress concentrations near fuel cracks on cladding creep damage is small

Investigation of the ramp testing behaviour of fuel pins with different diameters

International Nuclear Information System (INIS)

Pott, G.; Herren, M.; Wigger, B.

1979-09-01

The aim of these experiments was the investigation of the influence of different fuel pin diameter on the ramp testing behaviour. Fuel elements with diameter between 10,75 and 15,6 mm and different cladding thickness had been ramptested in the HBWR (Halden Boiling Water Reactor) after preirradiated in the same facility. Fuel pins with the smallest diameter of 10,75 mm failed. This was indicated by fission gas release measurement. Metallographic examination showed these failure were caused by hydride blisters. A systematic influence of fuel pin diameter and cladding thickness on the ramptesting behaviour was not observed. (orig.) [de

Advanced control system for the Integral Fast Reactor fuel pin processor

International Nuclear Information System (INIS)

Lau, L.D.; Randall, P.F.; Benedict, R.W.; Levinskas, D.

1993-01-01

A computerized control system has been developed for the remotely-operated fuel pin processor used in the Integral Fast Reactor Program, Fuel Cycle Facility (FCF). The pin processor remotely shears cast EBR- reactor fuel pins to length, inspects them for diameter, straightness, length, and weight, and then inserts acceptable pins into new sodium-loaded stainless-steel fuel element jackets. Two main components comprise the control system: (1) a programmable logic controller (PLC), together with various input/output modules and associated relay ladder-logic associated computer software. The PLC system controls the remote operation of the machine as directed by the OCS, and also monitors the machine operation to make operational data available to the OCS. The OCS allows operator control of the machine, provides nearly real-time viewing of the operational data, allows on-line changes of machine operational parameters, and records the collected data for each acceptable pin on a central data archiving computer. The two main components of the control system provide the operator with various levels of control ranging from manual operation to completely automatic operation by means of a graphic touch screen interface

TEMP: a computer code to calculate fuel pin temperatures during a transient

International Nuclear Information System (INIS)

Bard, F.E.; Christensen, B.Y.; Gneiting, B.C.

1980-04-01

The computer code TEMP calculates fuel pin temperatures during a transient. It was developed to accommodate temperature calculations in any system of axi-symmetric concentric cylinders. When used to calculate fuel pin temperatures, the code will handle a fuel pin as simple as a solid cylinder or as complex as a central void surrounded by fuel that is broken into three regions by two circumferential cracks. Any fuel situation between these two extremes can be analyzed along with additional cladding, heat sink, coolant or capsule regions surrounding the fuel. The one-region version of the code accurately calculates the solution to two problems having closed-form solutions. The code uses an implicit method, an explicit method and a Crank-Nicolson (implicit-explicit) method

Setting for technological control of vibropacked uranium-plutonium fuel pins

International Nuclear Information System (INIS)

Golushko, V.V.; Semenov, A.L.; Chukhlova, O.P.; Kuznetsov, A.M.; Korchkov, Yu.N.; Kandrashina, T.A.

1991-01-01

Scanning set-up providing for control of fuel pins by quality of fuel distribution in them is described. The gamma absorption method of fuel density measurement and the method of its own radiation registration are applied. Scintillation detection blocks are used in the measuring equipment mainly consisting of standard CAMAC blocks. Automation of measurements is performed on the basis of the computer complex MERA-60. A complex of programs for automation of the procedures under way is developed, when the facility operates within the test production line of vibroracked uranium-plutonium fuel pins. 6 refs.; 4 figs.; 1 tabs

The burnable poisons utilization for fissile enriched CANDU fuel bundle

Energy Technology Data Exchange (ETDEWEB)

Serghiuta, D; Nainer, O [Team 3 Solutions, Don Mills, ON (Canada)

1996-12-31

Utilization of burnable poison for the fissile enriched fueled CANDU 6 Mk1 core is investigated. The main incentives for this analysis are the reduction of void reactivity effects, the maximization of the fissile content of fresh fuel bundles, and the achievement of better power shape control, in order to preserve the power envelope of the standard 37 rod fuel bundle. The latter allows also the preservation of construction parameters of the standard core (for example: number and location of reactivity devices). It also permits the use of regular shift fueling schemes. The paper makes analyses of MOX weapons-grade plutonium and 1.2% SEU fueled CANDU 6 Mk 1 cores. (author). 6 refs., 4 tabs., 10 figs.

Fabrication drawings of fuel pins for FUJI project among PSI, JNC and NRG. Revised version

International Nuclear Information System (INIS)

Ozawa, Takayuki; Nakazawa, Hiroaki; Abe, Tomoyuki; Nagayama, Masahiro

2002-02-01

Irradiation tests and post-irradiation examinations in the framework of JNC-PSI-NRG collaboration project will be performed in 2003-2005. Irradiation fuel pins will be fabricated by the middle of 2003. The fabrication procedure for irradiation fuel pins has been started in 2001. Several fabrication tests and qualification tests in JNC and PSI (Paul Scherrer Institute, Switzerland) have been performed before the fuel pin fabrication. According to the design assignment between PSI and JNC in the frame of this project, PSI should make a specification document for the fuel pellet, the sphere-pac fuel particles, the vipac fuel particles, and the fuel pin. JNC should make a fabrication drawing for irradiation pins. JNC has been performed the fuel design in cooperation with PSI and NRG (Nuclear Research and Consultancy Group, Netherlands). In this project, the pelletized fuel, the sphere-pac fuel, and the vipac fuel will be simultaneously irradiated on HFR (High Flux Reactor, Netherlands). This fabrication drawing has been made under the design assignment with PSI, and consists of the drawing of MOX pellet, thermal insulator pellet, pin components, fuel segments, and the constructed pin. The fabrication drawings were approved in October 2001, but after that, the optimization of specifications has been discussed and agreed among all partners. In this report, the revised fabrication drawings will be shown. Based on the commission of Plutonium Fuel Technology Group, Advanced Fuel Recycle Technology Division, this design work has been performed in Fuel Design and Evaluation Group, Plutonium Fuel Fabrication Division, Plutonium Fuel Center. (author)

In-pile observations of fuel and clad relocation during LMFBR initiation phase accident experiments - the STAR experiments

International Nuclear Information System (INIS)

Wright, S.A.; Schumacher, G.; Henkel, P.R.; Royl, P.

1987-01-01

A series of seven in-pile experiments (the STAR experiments) were performed in which clad motion and fuel dispersal were observed in small pin bundles with high-speed cinematography. The experimental heating conditions reproduced a range of Loss of Flow (LOF) accident scenarios for the lead subassemblies in LMFBRs. The experiments show strong tendencies for limited clad motion in multiple pin bundles, early fuel disruption and dispersal (prior to fuel melting) in moderate power transients having simultaneous clad melting and fuel disruption. The more recent experiments indicate a possibility of steel vapor driven fuel dispersal after fuel breakup and intimate fuel/steel mixing. (author)

Fast reactor fuel pin behavior analyses in a LOF type transient event

International Nuclear Information System (INIS)

Mizuno, Tomoyasu; Koyama, Shin-ichi; Kaito, Takeji; Uwaba, Tomoyuki; Tanaka, Kenya

2013-06-01

In order to evaluate integrity limiting parameters of fuel pins during fast reactor core transient events, such as fuel center line temperature and cladding maximum temperature, fuel pin behavior calculations were made using the fast reactor fuel pin performance code CEDAR. The temperature histories of fuel pins during a loss of flow (LOF) type transient events was calculated based on Ross and Stoute type gap conductance model and constant gap conductance model, which is used in a core transient calculation code like HIPRAC. The calculated maximum temperatures of cladding and adjacent coolant channel were lower in the case with Ross and Stoute type model than in the case of constant gap conductance model due to the dynamic change of gap conductance of former case. It is indicated that core transient calculations with constant gap conductance give conservative cladding and coolant temperatures than that with Ross and Stoute type gap conductance model which is thought to be realistic. (author)

Demonstrating the compatibility of Canflex fuel bundles with a CANDU 6 fuelling machine

Energy Technology Data Exchange (ETDEWEB)

Alavi, P; Oldaker, I E [Atomic Energy of Canada Ltd., Mississauga, ON (Canada); Suk, H C; Choi, C B [Korea Atomic Energy Research Inst., Taejon (Korea, Republic of)

1997-12-31

CANFLEX is a new 43-element fuel bundle, designed for high operating margins. It has many small-diameter elements in its two outer rings, and large-diameter elements in its centre rings. By this means, the linear heat ratings are lower than those of standard 37-element bundles for similar power outputs. A necessary part of the out-reactor qualification program for the CANFLEX fuel bundle design, is a demonstration of the bundle`s compatibility with the mechanical components in a CANDU 6 Fuelling Machine (FM) under typical conditions of pressure, flow and temperature. The diameter of the CANFLEX bundle is the same as that of a 37-element bundle, but the smaller-diameter elements in the outer ring result in a slightly larger end-plate diameter. Therefore, to minimize any risk of unanticipated damage to the CANDU 6 FM sidestops, a series of measurements and static laboratory tests were undertaken prior to the fuelling machine tests. The tests and measurements showed that; a) the CANFLEX bundle end plate is compatible with the FM sidestops, b) all the dimensions of the CANFLEX fuel bundle are within the specified limits. (author). 3 tabs., 3 figs.

Integrated quality status and inventory tracking system for FFTF driver fuel pins

International Nuclear Information System (INIS)

Gottschalk, G.P.

1979-11-01

An integrated system for quality status and inventory tracking of Fast Flux Test Facility (FFTF) driver fuel pins has been developed. Automated fuel pin identification systems, a distributed computer network, and a data base are used to implement the tracking system

Characteristics of CANDU fuel bundles that caused pressure tube fretting at the bundle midplane

Energy Technology Data Exchange (ETDEWEB)

Dennier, D; Manzer, A M [Atomic Energy of Canada Ltd., Mississauga, ON (Canada); Koehn, E [Ontario Hydro, Toronto, ON (Canada)

1996-12-31

Detailed measurements on new bundles, and those that caused fretting during in- and out-reactor tests, have given insight into the factors responsible for fretting at the midplane of the inlet bundle. Bottom fuel elements that were attached near radial endplate spokes and had inboard bearing pads in the rolled joint cavity produced a significant portion of the observed fret marks. These elements are influenced by several driving forces that deflect the centre bearing pads towards the pressure tube surface. The evidence suggests that slight changes in bundle design may be possible to reduce pressure tube fretting. (author). 4 refs., 3 tabs., 8 figs.

Parallel two-phase-flow-induced vibrations in fuel pin model

International Nuclear Information System (INIS)

Hara, Fumio; Yamashita, Tadashi

1978-01-01

This paper reports the experimental results of vibrations of a fuel pin model -herein meaning the essential form of a fuel pin from the standpoint of vibration- in a parallel air-and-water two-phase flow. The essential part of the experimental apparatus consisted of a flat elastic strip made of stainless steel, both ends of which were firmly supported in a circular channel conveying the two-phase fluid. Vibrational strain of the fuel pin model, pressure fluctuation of the two-phase flow and two-phase-flow void signals were measured. Statistical measures such as power spectral density, variance and correlation function were calculated. The authors obtained (1) the relation between variance of vibrational strain and two-phase-flow velocity, (2) the relation between variance of vibrational strain and two-phase-flow pressure fluctuation, (3) frequency characteristics of variance of vibrational strain against the dominant frequency of the two-phase-flow pressure fluctuation, and (4) frequency characteristics of variance of vibrational strain against the dominant frequency of two-phase-flow void signals. The authors conclude that there exist two kinds of excitation mechanisms in vibrations of a fuel pin model inserted in a parallel air-and-water two-phase flow; namely, (1) parametric excitation, which occurs when the fundamental natural frequency of the fuel pin model is related to the dominant travelling frequency of water slugs in the two-phase flow by the ratio 1/2, 1/1, 3/2 and so on; and (2) vibrational resonance, which occurs when the fundamental frequency coincides with the dominant frequency of the two-phase-flow pressure fluctuation. (auth.)

Calculation of fuel pin failure timing under LOCA conditions

International Nuclear Information System (INIS)

Jones, K.R.; Wade, N.L.; Siefken, L.J.; Straka, M.; Katsma, K.R.

1991-10-01

The objective of this research was to develop and demonstrate a methodology for calculation of the time interval between receipt of the containment isolation signals and the first fuel pin failure for loss-of-coolant accidents (LOCAs). Demonstration calculations were performed for a Babcock and Wilcox (B ampersand W) design (Oconee) and a Westinghouse (W) 4-loop design (Seabrook). Sensitivity studies were performed to assess the impacts of fuel pin burnup, axial peaking factor, break size, emergency core cooling system (ECCS) availability, and main coolant pump trip on these items. The analysis was performed using a four-code approach, comprised of FRAPCON-2, SCDAP/RELAP5/MOD3, TRAC-PF1/MOD1, and FRAP-T6. In addition to the calculation of timing results, this analysis provided a comparison of the capabilities of SCDAP/RELAP5/MOD3 with TRAC-PF1/MOD1 for large-break LOCA analysis. This paper discusses the methodology employed and the code development efforts required to implement the methodology. The shortest time intervals calculated between initiation of containment isolation and fuel pin failure were 11.4 s and 19.1 for the B ampersand W and W plants, respectively. The FRAP-T6 fuel pin failure times calculated using thermal-hydraulic data generated by SCDAP/RELAP5/MOD3 were more conservative than those calculated using data generated by TRAC-PF1/MOD1. 18 refs., 7 figs., 4 tabs

WWER-440 fuel rod performance analysis with PIN-Micro and TRANSURANUS codes

International Nuclear Information System (INIS)

Vitkova, M.; Manolova, M.; Stefanova, S.; Simeonova, V.; Passage, G.; Lassmann, K.

1994-01-01

PIN-micro and TRANSURANUS codes were used to analyse the WWER-440 fuel rod behaviour at normal operation conditions. Two highest loaded fuel rods of the fuel assemblies irradiated in WWER-440 with different power histories were selected. A set of the most probable average values of all geometrical and technological parameters were used. A comparison between PIN-micro and TRANSURANUS codes was performed using identical input data. The results for inner gas pressure, gap size, local linear heat rate, fuel central temperature and fission gas release as a function of time calculated for the selected fuel rods are presented. The following conclusions were drawn: 1) The PIN-micro code predicts adequately the thermal and mechanical behaviour of the two fuel rods; 2) The comparison of the results obtained by PIN-micro and TRANSURANUS shows a reasonable agreement and the discrepancies could be explained by the lack of thoroughly WWER oriented verification of TRANSURANUS; 3) The advanced TRANSURANUS code could be successfully applied for WWER fuel rod thermal and mechanical analysis after incorporation of all necessary WWER specific material properties and models for the Zr+1%Nb cladding, for the fuel rod as a whole and after validation against WWER experimental and operational data. 1 tab., 10 figs., 10 refs

AGR fuel pin pellet-clad interaction failure limits and activity release fractions

International Nuclear Information System (INIS)

Hughes, H.; Hargreaves, R.

1985-01-01

The limiting conditions beyond which pellet-clad interaction can flail AGR fuel are described. They have been determined by many experiments involving post-irradiation examination and testing, loop experiments and cycling and up-rating of both individual fuel stringers and the whole WAGR core. The mechanisms causing this interaction are well understood and are quantitatively expressed in computer codes. Strain concentration effects over fuel cracks determine power cycling endurance while additional strain concentrations at clad ridges and from cross pin temperature gradients contribute to up-rating failures. An equation summarising tube burst test data so as to determine the ductility available at any transient is given. The hollow fuel and more ductile clad of the Civil AGR fuel pins leads to a much improved performance over the original fuel design. The Civil AGRs operate well within these limiting conditions and substantial increases beyond the design burn-up are confidently expected. The activity release on pin failure and its development during continued operation of failed fuel have also been investigated. A retention of radioiodine and caesium of 90-99% compared to the noble gases has been demonstrated. Measured fission gas releases into the free volume of Civil AGR fuel pins have been very low (< 0.1%)

WWER-440 fuel rod performance analysis with PIN-Micro and TRANSURANUS codes

Energy Technology Data Exchange (ETDEWEB)

Vitkova, M; Manolova, M; Stefanova, S; Simeonova, V; Passage, G [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. za Yadrena Izsledvaniya i Yadrena Energetika; Kharalampieva, Ts [Kombinat Atomna Energetika, Kozloduj (Bulgaria); Lassmann, K [European Atomic Energy Community, Karlsruhe (Germany). European Inst. for Transuranium Elements

1994-12-31

PIN-micro and TRANSURANUS codes were used to analyse the WWER-440 fuel rod behaviour at normal operation conditions. Two highest loaded fuel rods of the fuel assemblies irradiated in WWER-440 with different power histories were selected. A set of the most probable average values of all geometrical and technological parameters were used. A comparison between PIN-micro and TRANSURANUS codes was performed using identical input data. The results for inner gas pressure, gap size, local linear heat rate, fuel central temperature and fission gas release as a function of time calculated for the selected fuel rods are presented. The following conclusions were drawn: (1) The PIN-micro code predicts adequately the thermal and mechanical behaviour of the two fuel rods; (2) The comparison of the results obtained by PIN-micro and TRANSURANUS shows a reasonable agreement and the discrepancies could be explained by the lack of thoroughly WWER oriented verification of TRANSURANUS; (3) The advanced TRANSURANUS code could be successfully applied for WWER fuel rod thermal and mechanical analysis after incorporation of all necessary WWER specific material properties and models for the Zr+1%Nb cladding, for the fuel rod as a whole and after validation against WWER experimental and operational data. 1 tab., 10 figs., 10 refs.

Fuel assembly insertion system

International Nuclear Information System (INIS)

Barkhurst, D.J.

1987-01-01

This patent describes a nuclear reactor facility having fuel bundles: a system for the insertion of a fuel bundle into a position where vertically arranged fuel bundles surround and are adjacent the system comprising, in combination, separate and individual centering devices secured to and disposed on top of each fuel bundle adjacent the position. Each such centering device has a generally box-like cap configuration on the upper end of each fuel bundle and includes: a top wall; first and second side walls, each secured along and upper edge to the top wall; a rear plate attached along opposite vertical edges to the first and second side walls; a front inclined wall joined along an upper edge to the top to the wall and attached along opposite vertical edges first and second side walls; pad means secured to the lower edge of the first and second side walls, the front inclined wall and the rear plate for mounting each centering device on top of an associated fuel bundle; pin means carried by at least two of the pad means engageable with an associated aperature for locating and laterally fixing each centering device on top of its respective fuel bundle. Each front inclined wall of each of the centering devices is orientated on top of its respective fuel bundle to slope upwardly and away from the position where upon downward insertion of a fuel bundle any contact between the lower end of the fuel bundle inserted with a front inclined wall of a centering device will laterally deflect the fuel bundle. Each centering device further includes a central socket means secured to the top wall, and an elongated handling pole pivotally attached to the socket

SIFAIL: a subprogram to calculate cladding deformation and damage for fast reactor fuel pins

International Nuclear Information System (INIS)

Wilson, D.R.; Dutt, D.S.

1979-05-01

SIFAIL is a series of subroutines used in conjunction with the thermal performance models of SIEX to assist in the evaluation of mechanical performance of mixed uranium plutonium oxide fuel pins. Cladding deformations due to swelling and creep are calculated. These have been compared to post-irradiation data from fuel pin tests in EBR-II. Several fuel pin cladding failure criteria (cumulative damage, total strain, and thermal creep strain) are evaluated to provide the fuel pin designer with a basis to select design parameters. SIFAIL allows the user many property options for cladding material. Code input is limited to geometric and environmental parameters, with a consistent set of material properties provided by the code. The simplified, yet adequate, thin wall stress--strain calculations provide a reliable estimate of fuel pin mechanical performance, while requiring a small amount of core storage and computer running time

In-Core Fuel Managements for PWRs: Investigation on solution for optimal utilization of PWR fuel through the use of fuel assemblies with differently enriched 235U fuel pins

International Nuclear Information System (INIS)

Caprioli, Sara

2004-04-01

A possibility for more efficient use of the nuclear fuel in a pressurized water reactor is investigated. The alternative proposed here consists of the implementation of PWR fuel assemblies with differently enriched 235 U fuel pins. This possibility is examined in comparison with the standard assembly design. The comparison is performed both in terms of single assembly performance and in the terms of nuclear reactor core performance and fuel utility. For the evaluation of the actual performance of the new assembly types, 5 operated fuel core sequences of R3 (Ringhals' third unit), for the period 1999 - 2004 (cycles 17 - 21) were examined. For every cycle, the standard fresh fuel assemblies have been identified and taken as reference cases for the study of the new type of assemblies with differently enriched uranium rods. In every cycle, assemblies with and without burnable absorber are freshly loaded into the core. The axial enrichment distribution is kept uniform, allowing for a radial (planar) enrichment level distribution only. At an assembly level, it has been observed that the implementation of the alternative enrichment configuration can lead to lower and flatter internal peaking factor distribution with respect to the uniformly enriched reference assemblies. This can be achieved by limiting the enrichment levels distribution to a rather narrow range. The highest enrichment level chosen has the greatest impact on the power distribution of the assemblies. As it increases, the enrichment level drives the internal peaking factor to greater values than in the reference assemblies. Generally, the highest enrichment level that would allow an improvement in the power performance of the assembly lies between 3.95 w/o and 4.17 w/o. The highest possible enrichment level depends on the average enrichment of the overall assembly, which is kept constant to the average enrichment of the reference assemblies. The improvements that can be obtained at this level are rather

Fabrication of uranium-plutonium mixed nitride fuel pins (88F-5A) for first irradiation test at JMTR

International Nuclear Information System (INIS)

Suzuki, Yasufumi; Iwai, Takashi; Arai, Yasuo; Sasayama, Tatsuo; Shiozawa, Ken-ichi; Ohmichi, Toshihiko; Handa, Muneo

1990-07-01

A couple of uranium-plutonium mixed nitride fuel pins was fabricated for the first irradiation tests at JMTR for the purpose of understanding the irradiation behavior and establishing the feasibility of nitride fuels as advanced FBR fuels. The one of the pins was fitted with thermocouples in order to observe the central fuel temperature. In this report, the fabrication procedure of the pins such as pin design, fuel pellet fabrication and characterizations, welding of fuel pins, and inspection of pins are described, together with the outline of the new TIG welder installed recently. (author)

Hydraulic characteristics of a fast reactor fuel subassembly: An experimental investigation

International Nuclear Information System (INIS)

Padmakumar, G.; Velusamy, K.; Prasad, B.V.S.S.; Rajan, K.K.

2017-01-01

Highlights: • Fuel subassembly bundle geometry is studied for its hydraulic behaviour. • The results are also compared with data available in literature. • All flow regimes viz. laminar, transition and turbulent is covered for the study. • Pressure drop across different regions of subassembly was also determined. • The effect of external blockage is also studied and reported. - Abstract: Fuel subassemblies of a fast reactor consist of fuel pin bundle with helically wound spacer wires, arranged in a triangular pitch within a hexagonal wrapper. The fuel pins are located within the subassembly. Further the subassembly comprises of a diffuser where the cross section changes from cylindrical to hexagonal, mixing plenum before the exit of pin bundle and a specially designed blockage adapter. Accurate assessment of the pressure drop in the fuel subassembly is essential to ensure adequate core cooling and design of sodium pump. Experimental determination of pressure drop characteristics in the subassembly by simulating the hydraulic condition in the subassemblies of the reactor core is considered essential as a better choice as correlations reported in the literature cannot be directly used for all the complex regions present in the subassembly. This is due to the fact that flows in the interconnecting sections are highly under developed. Further, the flow regime in a fuel subassembly varies from laminar (during shutdown heat removal under natural convection) to completely turbulent under full power condition. To understand the hydraulic characteristics of the 500 MWe Proto type Fast Breeder Reactor (PFBR) fuel subassembly, an experimental facility has been commissioned. Experiments on full scale subassembly with dummy fuel pins have been performed using water as simulant. Experiments have been conducted covering a wide range of Reynolds number encompassing laminar, transition and turbulent regimes. In the rod bundle, no abrupt changes in friction factor were

In-Core Fuel Managements for PWRs: Investigation on solution for optimal utilization of PWR fuel through the use of fuel assemblies with differently enriched {sup 235}U fuel pins

Energy Technology Data Exchange (ETDEWEB)

Caprioli, Sara

2004-04-01

A possibility for more efficient use of the nuclear fuel in a pressurized water reactor is investigated. The alternative proposed here consists of the implementation of PWR fuel assemblies with differently enriched {sup 235}U fuel pins. This possibility is examined in comparison with the standard assembly design. The comparison is performed both in terms of single assembly performance and in the terms of nuclear reactor core performance and fuel utility. For the evaluation of the actual performance of the new assembly types, 5 operated fuel core sequences of R3 (Ringhals' third unit), for the period 1999 - 2004 (cycles 17 - 21) were examined. For every cycle, the standard fresh fuel assemblies have been identified and taken as reference cases for the study of the new type of assemblies with differently enriched uranium rods. In every cycle, assemblies with and without burnable absorber are freshly loaded into the core. The axial enrichment distribution is kept uniform, allowing for a radial (planar) enrichment level distribution only. At an assembly level, it has been observed that the implementation of the alternative enrichment configuration can lead to lower and flatter internal peaking factor distribution with respect to the uniformly enriched reference assemblies. This can be achieved by limiting the enrichment levels distribution to a rather narrow range. The highest enrichment level chosen has the greatest impact on the power distribution of the assemblies. As it increases, the enrichment level drives the internal peaking factor to greater values than in the reference assemblies. Generally, the highest enrichment level that would allow an improvement in the power performance of the assembly lies between 3.95 w/o and 4.17 w/o. The highest possible enrichment level depends on the average enrichment of the overall assembly, which is kept constant to the average enrichment of the reference assemblies. The improvements that can be obtained at this level are

Critical heat flux tests for self-spaced square finned 7 fuel rod bundle

International Nuclear Information System (INIS)

Moon, Sang Ki; Chun, Se Young; Choi, Ki Young; Park, Jong Kuk; Hwang, Dae Hyun; Zee, Sung Quun; Kim, Keung Koo

2001-09-01

Now, KAERI is developing a new advanced reactor aimed at achieving highly enhanced safety and reliability, and improved economics. SSF (Self-Spaced Square Finned) fuel rod bundle is considered as a suitable one for the new advanced reactor. The SSF fuel rods have rectangular shapes and four fins at the corners, and are arranged in triangular geometry. While the SSF fuel rod bundle is considered to have enhanced cooling efficiency, the correlations used for commercial PWR might be able to be applied. The application results of some conventional correlations show that the SSF fuel rod bundle show an enhanced CHF performance about 10 to 40 %. When some conventional CHF correlations are applied to CHF data with a similar geometry to the SSF fuel rod bundle, conventional CHF correlations including a correlation developed in Russia are judged not to be suitable for the development of SSF fuel rod bundle and for the use in a safety analysis code. From CHF experiments for SSF 7 fuel rod bundle performed in KAERI, the following results are obtained: the CHF increases with increasing mass flux, and the CHF increasing rate decreases at high mass flux conditions. The exit quality decreases with increasing mass flux. The overall effect of the mass flux on the CHF and exit quality coincides with previous understanding. Compared to the CHF data of IPPE with the same system pressure and inlet temperature, the CHF data of KAERI show the similar values. Thus, the reliability of IPPE CHF data can be confirmed indirectly

The design of the DUPIC spent fuel bundle counter

International Nuclear Information System (INIS)

Menlove, H.O.; Rinard, P.M.; Kroncke, K.E.; Lee, Y.G.

1997-05-01

A neutron coincidence detector had been designed to measure the amount of curium in the fuel bundles and associated process samples used in the direct use of plutonium in Canadian deuterium-uranium (CANDU) fuel cycle. All of the sample categories are highly radioactive from the fission products contained in the pressurized water reactor (PWR) spent fuel feed stock. Substantial shielding is required to protect the He-3 detectors from the intense gamma rays. The Monte Carlo neutron and photon calculational code has been used to design the counter with a uniform response profile along the length of the CANDU-type fuel bundle. Other samples, including cut PWR rods, process powder, waste, and finished rods, can be measured in the system. This report describes the performance characteristics of the counter and support electronics. 3 refs., 23 figs., 6 tabs

Modeling of WWER-440 Fuel Pin Behavior at Extended Burn-up

International Nuclear Information System (INIS)

El-Koliel, M.S.; Abou-Zaid, A.A.; El-Kafas, A.A.

2004-01-01

Currently, there is an ongoing effort to increase fuel discharge burn-up of all LWRs fuel including WWER's as much as possible in order to decrease power production cost. Therefore, burn-up is expected to be increased to 60 to 70 Mwd/kg U. The change in the fuel radial power distribution as a function of fuel burn up can affect the radial fuel temperature distribution as well as the fuel microstructure in the fuel pellet rim. In this paper, the radial burn-up and fissile products distributions of WWER-440 UO 2 fuel pin were evaluated using MCNP 4B and ORIGEN2 codes. The impact of the thermal conductivity on predicted fission gas release calculations is needed. For the analysis, a typical WWER-440 fuel pin and surrounding water moderator are considered in a hexagonal pin cell well. The thermal release and the athermal release from the pellet rim were modeled separately. The fraction of the rim structure and the excessive porosity in the rim structure in isothermal irradiation as a function of the fuel burn-up was predicted. a computer program; RIMSC-01, is developed to perform the required FGR calculations. Finally, the relevant phenomena and the corresponding models together with their validation are presented

Metallographic examinations of the wear-marks on fuel pins of the KNK II/2 fuel assembly NY-308

International Nuclear Information System (INIS)

Patzer, G.

1987-12-01

On the fuel pins and pin spacers of the fuel assembly NY-308 of the second core of KNK II pronounced wear marks had been found in the area of the contact points. In order to determine the exact form of the marks, metallographic investigations were performed on two test pieces of fuel pins in the Hot Cells of the KfK Karlsruhe. It was found that the wear marks did show the already observed stratified structure. Next to the unchanged cladding area there is a peripheral zone with modified grain structure, followed by a layer of moved material and finally there is a flake-like zone of accumulated cladding material at the lower end of the wear marks. Longitudinal cuts do not show grain deformations, which could indicate axial friction forces between pin and spacer. The wear marks are rapidly dropping to their maximum depth at the ends and the depth shows a relatively uniform pattern between both. The findings are confirming the picture, that a stirring movement of the fuel pins took place, which caused adhesive wear [de

Burnable poison option for DUPIC fuel

International Nuclear Information System (INIS)

Choi, Hang Bok; Cupta, H. P.

1996-08-01

The mechanisms of positive coolant void reactivity of CANDU natural uranium and DUPIC fuel have been studied. The design study of DUPIC fuel was performed using the burnable poison material in the center pin to reduce the coolant void reactivity. The amount of burnable poison was determined such that the prompt inverse period of DUPIC fuel upon full coolant voiding is the same as that of natural uranium fuel at equilibrium burnup. A parametric study on various burnable poisons has shown that natural dysprosium has more merit over other materials because it uniformly controls the void reactivity throughout the burnup with reasonable amount of poison. Additional studies on the option of using scattering or absorber material in the center pin position and the option using variable fuel density were performed. In any case of option using variable fuel density were performed. In any case of options to reduce the void reactivity, it was found that either the discharge burnup and/or the relative linear pin power are sacrificed. A preliminary study was performed for the evaluation of reference DUPIC fuel performance especially represented by Stress Corrosion Cracking(SCC) parameters which is mainly influenced by the refueling operations. For the reference 2-bundle shift refueling scheme, the predicted ramped power and power increment of the reference DUPIC fuel are below the SCC thresholds of CANDU natural uranium fuel. For a 4-bundle shift refueling scheme, the envelopes of element ramped power and power increment upon refueling are 8% and 44% higher than those of a 2-bundle shift refueling scheme on the average, respectively, but still have margins to the failure thresholds of natural uranium fuel. 23 tabs., 25 figs., 20 refs. (Author)

FFTF metal fuel pin sodium bond quality verification

International Nuclear Information System (INIS)

Pitner, A.L.; Dittmer, J.O.

1988-12-01

The Fast Flux Test Facility (FFTF) Series III driver fuel design consists of U-10Zr fuel slugs contained in a ferritic alloy cladding. A liquid metal, sodium bond between the fuel and cladding is required to prevent unacceptable temperatures during operation. Excessive voiding or porosity in the sodium thermal bond could result in localized fuel melting during irradiation. It is therefore imperative that bond quality be verified during fabrication of these metal fuel pins prior to irradiation. This document discusses this verification

French approach in fuel pin modelling for fast reactors

Energy Technology Data Exchange (ETDEWEB)

Pascard, R [CEA-Centre de Fontenay-aux-Roses, Fontenay-aux-Roses (France)

1979-12-01

The purpose of this paper is to present the general philosophy on the problem of fuel modelling now prevailing in France after a twelve years period of tremendously increasing knowledge on fuel behavior. When the Rapsodie fuel pin was designed in 1962 , little was known about the behavior of a mixed oxide fuel pin under fast flux ; but a large body of knowledge on UO{sub 2} behavior in thermal reactor was available together with some sparse irradiation results on (U Pu)O{sub 2} in French experimental reactors. The performances assigned to the pin were then rather modest in rating (400 w/cm) and in burnup (30,000 MWd/t). The AISI 316 steel in solution annealed state was chosen as cladding material. The clad itself was supposed to deform by thermal creep due to fission gas pressure (100% release), and was affected consequently by a strain limit criteria. The importance of clad temperature ({approx}650 deg.) was considered only in connection with thermal creep, the possibility of a chemical reaction between mixed oxide and clad being at that time hardly suspected. Rapsodie had only been at full power for a few months when appeared the evidence of stainless steel swelling under a fast neutrons flux. This swelling was observed on Rapsodie pins as soon as they experienced sufficient neutrons dose, roughly one year later. This entirely new problem came immediately in the front stage (and is still of major importance today), and was at the origin of the change from the Rapsodie to the Fortissimo core in order to accelerate materials testing versus void swelling by multiplying the flux by a factor two. Even with unforeseen swelling, the design of the Rapsodie and later on Fortissimo pin, allowed not only to reach the goal burnup, but to increase it steadily to roughly 100,000 MWd/t. Since then, the French approach in fuel pin design has still retained something of its original simplicity, and technological efficiency, attitude which is justified by the following

Performance of IN-706 and PE-16 cladding in mixed-oxide fuel pins

International Nuclear Information System (INIS)

Makenas, B.J.; Lawrence, L.A.; Jensen, B.W.

1982-05-01

Iron-nickel base, precipitation-strengthened alloys, IN-706 and PE-16, advanced alloy cladding considered for breeder reactor applications, were irradiated in mixed-oxide fuel pins in the HEDL-P-60 subassembly in EBR-II. Initial selection of candidate advanced alloys was done using only nonfueled materials test results. However, to establish the performance characteristics of the candidate cladding alloys, i.e., dimensional stability and structural integrity under conditions of high neutron flux, elevated temperature, and applied stress, it was necessary to irradiate fuel pins under typical operating conditions. Fuel pins were clad with solution treated IN-706 and PE-16 and irradiated to peak fluences of 6.1 x 10 22 n/cm 2 (E > .1 MeV) and 8.8 x 10 22 n/cm 2 (E > .1 MeV) respectively. Fabrication and operating parameters for the fuel pins with the advanced cladding alloy candidates are summarized. Irradiation of HEDL-P-60 was interrupted with the breach of a pin with IN-706 cladding at 5.1 at % and the test was terminated with cladding breach in a pin with PE-16 cladding at 7.6 at %

Assembly mechanism for nuclear fuel bundles

International Nuclear Information System (INIS)

Long, J.W.; Flora, B.S.; Ford, K.L.

1980-01-01

The invention relates to a nuclear power reactor fuel bundle of the type wherein several rods are mounted in parallel array between two tie plates which secure the fuel rods in place and are maintained in assembled position by means of a number of tie rods secured to both of the end plates. Improved apparatus is provided for attaching the tie rods to the upper tie plate by the use of locking lugs fixed to rotatable sleeves which engage the upper tie plate. (auth)

Radiographic examination methods for fuel pins

International Nuclear Information System (INIS)

Smirnov, V.P.; Dvoretskii, V.G.

1987-11-01

To study the fast neutron reactor fuel pins structure the NIIAR Institute used x diffraction, neutronic radiography and autoradiographies. The two first methods are used for internal macrostructure studies, the third method for the plutonium and uranium radial distribution. These methods and the main results are indicated in this document [fr

Fuel pin behavior under slow ramp-type transient-overpower conditions in the CABRI-FAST experiments

International Nuclear Information System (INIS)

Fukano, Yoshitaka; Onoda, Yuichi; Sato, Ikken; Charpenel, Jean

2009-01-01

In the CABRI-FAST experimental program, four in-pile tests were performed with slow power-ramp-type transient-overpower conditions (called hereafter as 'slow TOP') to study transient fuel pin behavior under inadvertent control rod withdrawal events in liquid metal cooled fast breeder reactors. Annular-pellet fuel pins were used in three tests, while a solid-pellet fuel pin was used in the other test. All of these pins were pre-irradiated in Phenix. The slow TOP test with a solid-pellet fuel pin was realized as a comparatory test against an existing test (E12) in the CABRI-2 program. In the CABRI-FAST test (BCF1), a power ramp rate of 3% Po/s was applied, while in the CABRI-2 test, 1% Po/s was adopted. Moreover, overpower condition was maintained for a few seconds beyond the observed pin failure in the BCF1 test. In spite of the different power ramp rates, evaluated fuel thermal conditions at the observed failure time are quite similar. The continued overpower condition in the BCF1 test resulted in gradual degradation of the pin structure providing information effective for evaluation of various accident scenarios. Three slow TOP tests with the annular fuel in the CABRI-FAST program resulted in no pin failure showing high failure threshold. Based on post-test examination data and a theoretical evaluation, it was concluded that intra-pin free spaces, such as central hole, macroscopic cracks and fuel-cladding gap effectively mitigated fuel cladding mechanical interaction. It was also clarified that cavity pressurization became effective only in case of very large amount of fuel melting. Furthermore, such cavity pressurization was effectively mitigated by a molten-fuel squirting into the upper blanket region pushing the blanket pellets upward. These CABRI FAST slow TOP tests, in combination with the existing CABRI and TREAT tests, provided an extended slow TOP test database with various fuel and transient conditions. (author)

FEA stress analysis considering cavity formation of metallic fuel pin under transient state

Energy Technology Data Exchange (ETDEWEB)

Jung, Hyun-Woo; Oh, Young-Ryun; Kim, Yun-Jae [Korea University, Seoul (Korea, Republic of)

2016-05-15

The aim of this research is to study the stress state of the fuel and the cladding under transient state using the commercial finite element analysis software, ABAQUS v6.13. It is checked out that the gap distance between the fuel and the cladding is a major factor determining FCMI stress. In this regard, initial boundary condition of the fuel pin such as the initial gap distance should be set carefully when the stress analysis of the fuel pin under transient state is conducted. In case of simulating cavity formation, it is confirmed that the new cavity simulation model that elements in cavity region lose their stiffness is valid. There is a great deal of research into SFR, which is one of GEN IV reactors. When it comes to the accidents of SFR, there are two cases of accident process. One of them is In-pin process that molten fuel is discharged into upper plenum. The other is Ex-pin process that the molten fuel is discharged into coolant because of breakage of cladding.

Infinite fuel element simulation of pin power distributions and control blade history in a BWR fuel assembly

Energy Technology Data Exchange (ETDEWEB)

Li, J.; Nuenighoff, K.; Allelein, H.J. [Forschungszentrum Juelich GmbH (DE). Inst. fuer Energie- und Klimaforschung (IEK), Sicherheitsforschung und Reaktortechnik (IEK-6)

2011-07-01

Pellet-Cladding Interaction (PCI) is a well known effect in fuel pins. One possible reason for PCI-effects could be local power excursions in the fuel pins, which can led to a rupture of the fuel cladding tube. From a reactor safety point of view this has to be considered as a violence of the barrier principal in order to retain fission products in the fuel pins. This paper focuses on the pin power distributions in a 2D infinite lattice of a BWR fuel element. Lots of studies related PCI effect can be found in the literature. In this compact, coupled neutronic depletion calculations taking the control history effect into account are described. Depletion calculations of an infinite fuel element of a BWR were carried out with controlled, uncontrolled and temporarily controlled scenarios. Later ones are needed to describe the control blade history (CBH) effect. A Monte-Carlo approach is mandatory to simulate the neutron physics. The VESTA code was applied to couple the Monte-Carlo-Code MCNP(X) with the burnup code ORIGEN. Additionally, CASMO-4 is also employed to verify the method of simulation results from VESTA. The cross sections for Monte Carlo and burn-up calculations are derived from ENDF/B-VII.0. (orig.)

Performance of fast reactor mixed-oxide fuels pins during extended overpower transients

International Nuclear Information System (INIS)

Tsai, H.; Neimark, L.A.; Asaga, T.; Shikakura, S.

1991-02-01

The Operational Reliability Testing (ORT) program, a collaborative effort between the US Department of Energy and the Power Reactor and Nuclear Fuel Development Corp. (PNC) of Japan, was initiated in 1982 to investigate the behavior of mixed-oxide fuel pin under various slow-ramp transient and duty-cycle conditions. In the first phase of the program, a series of four extended overpower transient tests, with severity sufficient to challenge the pin cladding integrity, was conducted. The objectives of the designated TOPI-1A through -1D tests were to establish the cladding breaching threshold and mechanisms, and investigate the thermal and mechanical effects of the transient on pin behavior. The tests were conducted in EBR-2, a normally steady-state reactor. The modes of transient operation in EBR-2 were described in a previous paper. Two ramp rates, 0.1%/s and 10%/s, were selected to provide a comparison of ramp-rate effects on fuel behavior. The test pins chosen for the series covered a range of design and pre-test irradiation parameters. In the first test (1A), all pins maintained their cladding integrity during the 0.1%/s ramp to 60% peak overpower. Fuel pins with aggressive designs, i.e., high fuel- smear density and/or thin cladding, were, therefore, included in the follow-up 1B and 1C tests to enhance the likelihood of achieving cladding breaching. In the meantime, a higher pin overpower capability, to greater than 100%, was established by increasing the reactor power limit from 62.5 to 75 MWt. In this paper, the significant results of the 1B and 1C tests are presented. 4 refs., 5 figs., 1 tab

Upon local blockage formations in LMFBR fuel rod bundles with wire-wrapped spacers

International Nuclear Information System (INIS)

Minden, C. v.; Schultheiss, G.F.

1982-01-01

A theoretical and experimental study, to improve understanding of local particle depositions in a wire-wrapped LMFBR fuel bundle, has been performed. Theoretical considerations show, that a preferentially axial process of particle depositions occurs. The experiments confirm this and clarify that the blockages arise near the particle source and settle at the spatially arranged minimum gaps in the bundle. The results suggest that, considering flow reduction, cooling and DND-detection, such fuel particle blockages are less dangerous. With reference to these safety-relevant factors, wire-wrapped LMFBR fuel bundles seem to gain advantages compared to the grid design. (orig.) [de

Developments in the LASL Fuel Pin Imaging System: PINEX-3A

International Nuclear Information System (INIS)

Lumpkin, A.H.; Berzins, G.J.; Cosimi, R.A.; O'Hare, T.E.; Davidson, J.R.

1979-01-01

The LASL Fuel Pin Imaging System was evaluated using a series of 10 TREAT transients, each of approx. 240-MW peak power. HEDL provided the fuel-ejection type capsule with annular fuel pellets. The pin visibility threshold was determined to be approx. 20-MW of TREAT power (approx. 130 W/g), almost an order of magnitude improvement over our PINEX-2 threshold. The impact of changes in instrumentation, imaging apertures, and fluors that produced the improved sensitivity are reported. Results of a time-integrated imaging technique are also presented

Research reactor fuel bundle design review by means of hydrodynamic testing

International Nuclear Information System (INIS)

Pastorini, A.; Belinco, C.

1997-01-01

During the design steps of a fuel bundle for a nuclear reactor, some vibration tests are usually necessary to verify the prototype dynamical response characteristics and the structural integrity. To perform these tests, the known hydrodynamic loop facilities are used to evaluate the vibrational response of the bundle under the different flow conditions that may appear in the reactor. This paper describes the tests performed on a 19 plate fuel bundle prototype designed for a low power research reactor. The tests were done in order to know the dynamical characteristics of the plates and also of the whole bundle under different flow rate conditions. The paper includes a description of the test facilities and the results obtained during the dynamical characterization tests and some preliminary comments about the tests under flowing water are also presented. (author) [es

Evaluation of existing correlations for the prediction of pressure drop in wire-wrapped hexagonal array pin bundles

International Nuclear Information System (INIS)

Chen, S.K.; Todreas, N.E.; Nguyen, N.T.

2014-01-01

Highlights: • Wire-wrapped bundle friction factor data and correlations thoroughly collected. • Three methodologies proposed for identifying the best fit correlation. • 80 out of 141 bundles selected as database for evaluation. • The detailed Cheng and Todreas correlation identified to fit the data best. - Abstract: Existing wire-wrapped fuel bundle friction factor correlations were evaluated to identify their comparative fit to the available pressure drop experimental data. Five published correlations, those of Rehme (REH), Baxi and Dalle Donne (BDD, which used the correlations of Novendstern in the turbulent regime and Engel et al. in the laminar and transition regimes), detailed Cheng and Todreas (CTD), simplified Cheng and Todreas (CTS), and Kirillov (KIR, developed by Russian scientists) were studied. Other correlations applicable to a specific case were also evaluated but only for that case. Among all 132 available bundle data, an 80 bundle data set was judged to be appropriate for this evaluation. Three methodologies, i.e., the Prediction Error Distribution, Agreement Index and Credit Score were principally used for investigating the goodness of each correlation in fitting the data. Evaluations have been performed in two categories: 4 cases of general user interest and 3 cases of designer specific interest. The four general user interest cases analyzed bundle data sets in four flow regimes – i.e., all regimes, the transition and/or turbulent regimes, the turbulent regime, and the laminar regime. The three designer interest cases analyzed bundles in the fuel group, the blanket and control group and those with P/D > 1.06, for the transition/turbulent regimes. For all these cases, the detailed Cheng and Todreas correlation is identified as yielding the best fit. Specifically for the all flow regimes evaluation, the best fit correlation in descending order is CTD, BDD/CTS (tie), REH and KIR. For the combined transition/turbulent regime, the order is

Comparative analysis of different methods of modelling of most loaded fuel pin in transients

International Nuclear Information System (INIS)

Ovdiyenko, Y.; Khalimonchuk, V.; Ieremenko, M.

2007-01-01

Different methods of modeling of most loaded fuel pin are presented at the work. Calculation studies are performed on example of accident related to WWER-1000 cluster rod ejection with using of spatial kinetic code DYN3D that uses nodal method to calculate distribution of neutron flux in the core. Three methods of modeling of most loaded fuel pin are considered - flux reconstruction in fuel macrocell, pin-by-pin calculation by using of DYN3D/DERAB package and by introducing of additional 'hot channel'. Obtained results of performed studies could be used for development of calculation kinetic models during preparing of safety analysis report (Authors)

Analytic models for fuel pin transient performance

International Nuclear Information System (INIS)

Bard, F.E.; Fox, G.L.; Washburn, D.F.; Hanson, J.E.

1976-09-01

HEDL's ability to analyze various mechanisms that operate within a fuel pin has progressed substantially through development of codes such as PECTCLAD, which solves cladding response, and DSTRESS, which solves fuel response. The PECTCLAD results show good correlation with a variety of mechanical tests on cladding material and also demonstrate the significance of cladding strength when applying the life fraction rule. The DSTRESS results have shown that fuel deforms sufficiently during overpower transient tests that available volumes are filled, whether in the form of a central cavity or start-up cracks

The application of safeguards design principles to the spent fuel bundle counter for 600 MW

International Nuclear Information System (INIS)

Stirling, A.J.; Allen, V.H.

1978-10-01

The irradiated fuel bundle counters for CANDU 600 MW reactors provide the IAEA with a secure and independent means of estimating the inventory of the spent fuel storage bay at each inspection. Their function is straightforward: to count the bundles entering the storage area through the normal transfer ports. However, location, reliability, security and operating requirements make them highly ΣintelligentΣ instruments which have required a major development program. Moreover, the bundle counters incorporate principles which apply to many unattended safeguards instruments. For example, concealing the operating status from potential diverters eases reliability specifications, continuous self-checking gives the inspector confidence in the readout, independence from continuous station services improves tamper resistance, and the detailed data display provides tamper indication and a high level of credibility. Each irradiated fuel bundle counter uses four Geiger counters to detect the passage of fuel bundles as they pass sequentially through the field-of-view. A Microprocessor analyzes the sequence of the Geiger counter signals and determines the number and direction of bundles transferred. The readout for IAEA inspectors includes both a tally and a printed log. The printer is also used to alert the inspector to abnomal fuel movements, tampering, Geiger counter failures and contamination of the fuel transfer mechanism. (author)

Program of quality management when fabricating fast reactor vibropack oxide fuel pins

International Nuclear Information System (INIS)

Mayorshin, A.A.; Kisly, V.A.; Sudakov, L.V.

2000-01-01

There are presented main principles of creation and operation of Quality Management Program in fabricating vibropack oxide fuel pins for BOR-60 and BN-600 being in force in SSC RF RIAR. There is given structure of documentation for QS principal elements. Under Quality System there are defined all the procedures, assuring that fuel pin meets the normative requirements. The system model is complied with the standard model IS 9001. There are shown technologic flowchart and check operation, statistic results of pin critical parameter check as well as main results of in-pile tests. (author)

Calculation Of A Lattice Physics Parameter For SBWR Fuel Bundle Design

International Nuclear Information System (INIS)

Sardjono, Y.

1996-01-01

The maximum power peaking factor for Nuclear Power Plant SBWR type is 1.5. The precision for that calculation is related with the result of unit cell analysis each rod in the fuel bundles. This analysis consist of lattice eigenvalue, lattice average diffusion cross section as well as relative power peaking factor in the fuel rod for each fuel bundles. The calculation by using TGBLA computer code which is based on the transport and 168 group diffusion theory. From this calculation can be concluded that the maximum relative power peaking factor is 1.304 and lower than design limit

Post-irradiation examination of CANDU fuel bundles fuelled with (Th, Pu)O2

International Nuclear Information System (INIS)

Karam, M.; Dimayuga, F.C.; Montin, J.

2010-01-01

AECL has extensive experience with thoria-based fuel irradiations as part of an ongoing R&D program on thorium within the Advanced Fuel Cycles Program. The BDL-422 experiment was one component of the thorium program that involved the fabrication and irradiation testing of six Bruce-type bundles fuelled with (Th, Pu)O 2 pellets. The fuel was manufactured in the Recycle Fuel Fabrication Laboratories (RFFL) at Chalk River allowing AECL to gain valuable experience in fabrication and handling of thoria fuel. The fuel pellets contained 86.05 wt.% Th and 1.53 wt.% Pu in (Th, Pu)O 2 . The objectives of the BDL-422 experiment were to demonstrate the ability of 37-element geometry (Th, Pu)O 2 fuel bundles to operate to high burnups up to 1000 MWh/kgHE (42 MWd/kgHE), and to examine the (Th, Pu)O 2 fuel performance. This paper describes the post-irradiation examination (PIE) results of BDL-422 fuel bundles irradiated to burnups up to 856 MWh/kgHE (36 MWd/kgHE), with power ratings ranging from 52 to 67 kW/m. PIE results for the high burnup bundles (>1000 MWh/kgHE) are being analyzed and will be reported at a later date. The (Th, Pu)O 2 fuel performance characteristics were superior to UO 2 fuel irradiated under similar conditions. Minimal grain growth was observed and was accompanied by benign fission gas release and sheath strain. Other fuel performance parameters, such as sheath oxidation and hydrogen distribution, are also discussed. (author)

Post-irradiation examination of overheated fuel bundles

International Nuclear Information System (INIS)

Sears, D.F.; Primeau, M.F.; Leach, D.A.

1995-01-01

Post-irradiation examinations (PIE) were conducted on prototype 43-element CANDU fuel bundles that overheated during test irradiations in the NRU reactor. PIE revealed that the bundles remained physically intact, but on several elements the Zr-4 sheath collapsed into axial gaps between the pellet stack and end caps, between adjacent pellets within the stacks, and into missing pellet chips and cracks. Helium pressurization tests showed that none of the collapsed elements leaked. Hydride blisters were discovered on a few elements, but the source of the hydrogen was not linked to a breach of the cladding or end caps. These defects were attributed to primary hydriding. Microstructural changes in the fuel and cladding indicate that the cladding-was briefly exposed to temperatures in the range 600-800 o C and pressures above 11.2 MPa. The results show that Zr-4 cladding behaves in a highly ductile manner during such transient, high-temperature and high-pressure excursions. (author)

Post-irradiation examination of overheated fuel bundles

International Nuclear Information System (INIS)

Sears, D.F.; Primeau, M.F.; Leach, D.A.

1997-08-01

Post-irradiation examinations (PIE) were conducted on prototype 43-element CANDU fuel bundles that overheated during test irradiations in the NRU reactor. PIE revealed that the bundles remained physically intact, but on several elements the Zr-4 sheath collapsed into axial gaps between the pellet stack and end caps, between adjacent pellets within the stacks, and into missing pellet chips and cracks. Helium pressurization tests showed that none of the collapsed elements leaked. Hydride blisters were discovered on a few elements, but the source of the hydrogen was.not linked to a breach of the cladding or end caps. These defects were attributed to primary hydriding. Microstructural changes in the fuel and cladding indicate that the cladding was briefly exposed to temperatures in the range 600-800 o C and pressures above 11.2MPa. The results show that Zr-4 cladding behaves in a highly ductile manner during such transient, high-temperature and high-pressure excursions. (author)

The lumped parameter model for fuel pins

Energy Technology Data Exchange (ETDEWEB)

Liu, W S [Ontario Hydro, Toronto, ON (Canada)

1996-12-31

The use of a lumped fuel-pin model in a thermal-hydraulic code is advantageous because of computational simplicity and efficiency. The model uses an averaging approach over the fuel cross section and makes some simplifying assumptions to describe the transient equations for the averaged fuel, fuel centerline and sheath temperatures. It is shown that by introducing a factor in the effective fuel conductivity, the analytical solution of the mean fuel temperature can be modified to simulate the effects of the flux depression in the heat generation rate and the variation in fuel thermal conductivity. The simplified analytical method used in the transient equation is presented. The accuracy of the lumped parameter model has been compared with the results from the finite difference method. (author). 4 refs., 2 tabs., 4 figs.

Post-test examination of the VVER-1000 fuel rod bundle CORA-W2

International Nuclear Information System (INIS)

Hofmann, P.; Noack, V.; Burbach, J.; Metzger, H.; Schanz, G.; Hagen, S.; Sepold, L.

1995-01-01

The upper half of the bundle is completely oxidized, the lower half has kept the fuel rods relatively intact. The post-test examination results show the strong impact of the B 4 C absorber rod and the stainless steel grid spacers on the 'low-temperature' bundle damage initiation and progression. The B 4 C absorber rod completely disappeared in the upper half of the bundle. The multicomponent melts relocated and formed coolant channel blockages on solidification with a maximum extent of about 30% in the lower part of the bundle. At temperatures above the melting point of the ZrNb1 cladding extensive fuel dissolution occured. (orig./HP)

Post-test examination of the VVER-1000 fuel rod bundle CORA-W2

Energy Technology Data Exchange (ETDEWEB)

Hofmann, P.; Noack, V.; Burbach, J.; Metzger, H.; Schanz, G.; Hagen, S.; Sepold, L.

1995-08-01

The upper half of the bundle is completely oxidized, the lower half has kept the fuel rods relatively intact. The post-test examination results show the strong impact of the B{sub 4}C absorber rod and the stainless steel grid spacers on the `low-temperature` bundle damage initiation and progression. The B{sub 4}C absorber rod completely disappeared in the upper half of the bundle. The multicomponent melts relocated and formed coolant channel blockages on solidification with a maximum extent of about 30% in the lower part of the bundle. At temperatures above the melting point of the ZrNb1 cladding extensive fuel dissolution occured. (orig./HP)

Mitigation of end flux peaking in CANDU fuel bundles using neutron absorbers

Energy Technology Data Exchange (ETDEWEB)

Pierce, D.; Chan, P.K., E-mail: dylan.pierce@rmc.ca [Royal Military College of Canada, Kingston ON, (Canada); Shen, W. [Canadian Nuclear Safety Commission, Ottawa ON, (Canada)

2015-07-01

End flux peaking (EFP) is a phenomenon where a region of elevated neutron flux occurs between two adjoining fuel bundles. These peaks lead to an increase in fission rate and therefore greater heat generation. It is known that addition of neutron absorbers into fuel bundles can help mitigate EFP, yet implementation in Canada Deuterium Uranium (CANDU) type reactors using natural uranium fuel has not been pursued. Monte Carlo N-Particle code (MCNP) 6.1 was used to simulate the addition of a small amount of neutron absorbers strategically within the fuel pellets. This paper will present some preliminary results collected thus far. (author)

CFD modeling of secondary flows in fuel rod bundles

International Nuclear Information System (INIS)

Baglietto, Emilio; Ninokata, Hisashi

2004-01-01

An optimized non-linear eddy viscosity model is introduced, for calculations of detailed coolant velocity distribution in a tight lattice fuel bundle. The low Reynolds formulation has been optimized based on DNS data for channel flow. The non-linear stress-strain relationship has been modified in the coefficients to model the flow anisotropy, which causes the formation of turbulence driven secondary flows inside the bundle subchannels. Predictions of the model are first compared to experimental measurements of secondary flows in a triangularly arrayed rod bundle with p/d=1.3. Subsequently wall shear stress and velocity predictions are compared with different experimental data for a rod bundle with p/d=1.17. The model shows to be able to correctly reproduce the scale of the secondary motion, and to accurately reproduce both wall shear stress and velocity distributions inside the rod bundle subchannels. (author)

Analysis of metallic fuel pin behaviors under transient conditions of liquid metal reactors

International Nuclear Information System (INIS)

Nam, Cheol; Kwon, Hyoung Mun; Hwang, Woan

1999-02-01

Transient behavior of metallic fuel pins in liquid metal reactor is quite different to that in steady state conditions. Even in transient conditions, the fuel may behave differently depending on its accident situation and/or accident sequence. This report describes and identifies the possible and hypothetical transient events at the aspects of fuel pin behavior. Furthermore, the transient experiments on HT9 clad metallic fuel have been analyzed, and then failure assessments are performed based on accident classes. As a result, the failure mechanism of coolant-related accidents, such as LOF, is mainly due to plenum pressure and cladding thinning caused by eutectic penetration. In the reactivity-related accidents, such as TOP, the reason to cladding failure is believed to be the fuel swelling as well as plenum pressure. The probabilistic Weibull analysis is performed to evaluate the failure behavior of HT9 clad-metallic fuel pin on coolant related accidents.The Weibull failure function is derived as a function of cladding CDF. Using the function, a sample calculation for the ULOF accident of EBR-II fuel is performed, and the results indicate that failure probability is less the 0.3%. Further discussion on failure criteria of accident condition is provided. Finally, it is introduced the state-of-arts for developing computer codes of reactivity-related fuel pin behavior. The development efforts for a simple model to predict transient fuel swelling is described, and the preliminary calculation results compared to hot pressing test results in literature.This model is currently under development, and it is recommended in the future that the transient swelling model will be combined with the cladding model and the additional development for post-failure behavior of fuel pin is required. (Author). 36 refs., 9 tabs., 18 figs

Large Eddy Simulation of turbulent flow in wire wrapped fuel pin bundles cooled by sodium

International Nuclear Information System (INIS)

Saxena, Aakanksha; Cadiou, Thierry; Bieder, Ulrich; Viazzo, Stephane

2013-06-01

The objective of the study is to understand the thermal hydraulics in a core sub-assembly with liquid sodium as coolant by performing detailed numerical simulations. The passage for the coolant flow between the fuel rods is maintained by thin wires wrapped around the rods. The contact point between the fuel pin and the spacer wire is the region of creation of hot spots and a cyclic variation of temperature in hot spots can adversely affect the mechanical properties of the clad due to the phenomena like thermal stripping. The current status quo provides two different models to perform the numerical simulations, namely Reynolds Averaged Navier-Stokes (RANS) and Large Eddy Simulation (LES). The two models differ in the extent of modelling used to close the Navier-Stokes equations. LES is a filtered approach where the large scale of motions are explicitly resolved while the small scale motions are modelled whereas RANS is a time averaging approach where all scale of motions are modelled. Thus LES involves less modelling as compared to RANS and so the results are comparatively more accurate. An attempt has been made to use the LES model. The simulations have been performed using the code Trio-U (developed by CEA). The turbulent statistics of the flow and thermal quantities are calculated. Finally the goal is to obtain the frequency of temperature oscillations at the region of hot spots near the spacer wire. (authors)

Image analysis for remote examination of fuel pins

International Nuclear Information System (INIS)

Cook, J.H.; Nayak, U.P.

1982-01-01

An image analysis system operating in the Wing 9 Hot Cell Facility at Los Alamos National Laboratory provides quantitative microstructural analyses of irradiated fuels and materials. With this system, fewer photomicrographs are required during postirradiation microstructural examination and data are available for analysis much faster. The system has been used successfully to examine Westinghouse Advanced Reactors Division experimental fuel pins

Axial migratin of cesium in LMFBR fuel pins

International Nuclear Information System (INIS)

Karnesky, R.A.; Bridges, A.E.; Jost, J.W.

1981-11-01

A correlated model for quantitatively predicting the behavior of cesium in LMFBR fuel pins has been developed. This correlation was shown to be in good agreement with experimental data. It has been used to predict the behavior of cesium in the FFTF driver fuel and as the result of this analysis it has been shown that the accumulation of cesium in the insulator pellets at the ends of the fuel column will not be life limiting

Material accountancy for metallic fuel pin casting

International Nuclear Information System (INIS)

Bucher, R.G.; Orechwa, Y.; Beitel, J.C.

1995-01-01

The operation of the Fuel Conditioning Facility (FCF) is based on the electrometallurgical processing of spent metallic reactor fuel. The pin casting operation, although only one of several operations in FCF, was the first to be on-line. As such, it has served to demonstrate the material accountancy system in many of its facets. This paper details, for the operation of the pin casting process with depleted uranium, the interaction between the mass tracking system (MTG) and some of the ancillary computer codes which generate pertinent information for operations and material accountancy. It is necessary to distinguish between two types of material balance calculations -- closeout for operations and material accountancy for safeguards. The two have much in common, for example, the mass tracking system database and the calculation of an inventory difference, but, in general, are not congruent with regard to balance period and balance spatial domain. Moreover, the objective, assessment, and reporting requirements of the calculated inventory difference are very different in the two cases

The fuel to clad heat transfer coefficient in advanced MX-type fuel pins

International Nuclear Information System (INIS)

Caligara, F.; Campana, M.; Mandler, R.; Blank, H.

1979-01-01

Advanced fuels (mixed carbides, nitrides and carbonitrides) are characterised by a high thermal conductivity compared to that of oxide fuels (5 times greater) and their behaviour under irradiation (amount of swelling, fracture behaviour, restructuring) is far more sensitive to the design parameters and to the operating temperature than that of oxide fuels. The use of advanced fuels is therefore conditioned by the possibility of mastering the above phenomena, and the full exploitation of their favorable neutron characteristics depends upon a good understanding of the mutual relationships of the various parameters, which eventually affect the mechanical stability of the pin. By far the most important parameter is the radial temperature profile which controls the swelling of the fuel and the build-up of stress fields within the pin. Since the rate of fission gas swelling of these fuels is relatively large, a sufficient amount of free space has to be provided within the pin. This space originally appears as fabrication porosity and as fuel-to-clad clearance. Due to the large initial gap width and to the high fuel thermal conductivity, the range of the fuel operating temperatures is mainly determined by the fuel-to-clad heat transfer coefficient h, whose correct determination becomes one of the central points in modelling. During the many years of modelling activity in the field of oxide fuels, several theoretical models have been developed to calculate h, and a large amount of experimental data has been produced for the empirical adjustment of the parameters involved, so that the situation may be regarded as rather satisfactory. The analysis lead to the following conclusions. A quantitative comparison of experimental h-values with existing models for h requires rather sophisticated instrumented irradiation capsules, which permit the measurement of mechanical data (concerning fuel and clad) together with heat rating and temperatures. More and better well

Development of inspection equipment for fuel bundles of CANDU-PHWR using R981 underwater radiation tolerant camera

Energy Technology Data Exchange (ETDEWEB)

Koo, Dae-Seo; Cho, Moon-Sung; Jo, Chang-Keun; Jun, Ji-Su; Jung, Jong Yeob; Park, Kwang-June; Suk, Ho-Chun

2005-03-15

The inspection equipment of fuel bundles was developed, which could perform visual inspection and dimensional measurement on fuel bundles of CANDU-PHWR, to evaluate, analyze the defective behavior of fuel bundles and inner surface of pressure tubes of inherent two-phase flow over 24kg/s in CANDU-6. The R981 radiation tolerant camera system with pan and tilt function was ordered and manufactured, which was waterproof, shielding radiation in underwater 10m in depth. The performance test, of the system ,due to camera-object distance was carried out in air/underwater atmosphere. The results of performance test of R981 radiation tolerant camera system are good. The inspection equipment of fuel bundles using R981 radiation tolerant camera system and underwater-radiation tolerant LVDT sensor(D5/200AW) was fabricated, which could perform visual inspection and dimensional measurement on fuel bundles of CANDU-PHWR with measurement accuracy 10{mu}m. This equipment will be utilizable integrity evaluation of fuel bundles which are irradiated in pressure tube of CANDU-PHWR.

Review of HEDL fuel pin transient analyses analytical programs

International Nuclear Information System (INIS)

Scott, J.H.; Baars, R.E.

1975-05-01

Methods for analysis of transient fuel pin performance are described, as represented by the steady-state SIEX code and the PECT series of codes used for steady-state and transient mechanical analyses. The empirical fuel failure correlation currently in use for analysis of transient overpower accidents is described. (U.S.)

Literature search on Light Water Reactor (LWR) fuel and absorber rod fabrication, 1960--1976

International Nuclear Information System (INIS)

Sample, C.R.

1977-02-01

A literature search was conducted to provide information supporting the design of a conceptual Light Water Reactor (LWR) Fuel Fabrication plant. Emphasis was placed on fuel processing and pin bundle fabrication, effects of fuel impurities and microstructure on performance and densification, quality assurance, absorber and poison rod fabrication, and fuel pin welding. All data have been taken from publicly available documents, journals, and books. This work was sponsored by the Finishing Processes-Mixed Oxide (MOX) Fuel Fabrication Studies program at HEDL

Literature search on Light Water Reactor (LWR) fuel and absorber rod fabrication, 1960--1976

Energy Technology Data Exchange (ETDEWEB)

Sample, C R [comp.

1977-02-01

A literature search was conducted to provide information supporting the design of a conceptual Light Water Reactor (LWR) Fuel Fabrication plant. Emphasis was placed on fuel processing and pin bundle fabrication, effects of fuel impurities and microstructure on performance and densification, quality assurance, absorber and poison rod fabrication, and fuel pin welding. All data have been taken from publicly available documents, journals, and books. This work was sponsored by the Finishing Processes-Mixed Oxide (MOX) Fuel Fabrication Studies program at HEDL.

Hydrodynamics around a spacer of a VVER-440 fuel rod bundle

International Nuclear Information System (INIS)

Mayer, G.; Hazi, G.; Kavran, P.

2004-01-01

Recently, an intensive research has been started in our institute, focusing on the hydrodynamics of fuel rod bundles. Numerical computations have been planed to be carried out in a three level bottom-up hierarchy, using direct numerical simulation, large eddy simulation and Reynolds averaged Navier-Stokes approach. Here, we give a description of the numerical method applied for direct numerical and large eddy simulation. We present some preliminary results obtained by the simulation of the flow around a spacer of a VVER-440 fuel rod bundle. (author)

Influence of LMFBR fuel pin temperature profiles on corrosion rate

International Nuclear Information System (INIS)

Shiels, S.A.; Bagnall, C.; Schrock, S.L.; Orbon, S.J.

1976-01-01

The paper describes the sodium corrosion behavior of 20 percent cold worked Type 316 stainless steel fuel pin cladding under a simulated reactor thermal environment. A temperature gradient, typical of a fuel pin, was generated in a 0.9 m long heater section by direct resistance heating. Specimens were located in an isothermal test section immediately downstream of the heater. A comparison of the measured corrosion rates with available data showed an enhancement factor of between 1.5 and 2 which was attributed to the severe axial temperature gradient through the heater. Differences in structure and surface chemistry were also noted

Application of safeguards design principles to the spent-fuel bundle counters for 600-MW CANDU reactors

International Nuclear Information System (INIS)

Stirling, A.J.; Allen, V.H.

1979-01-01

The irradiated fuel bundle counters for CANDU 600-MW reactors provide the IAEA with a secure and independent means of estimating the inventory of the spent-fuel storage bay at each inspection. Their function is straightforward - to count the bundles entering the storage area through the normal transfer ports. However, location, reliability, security and operating requirements make them highly ''intelligent'' instruments which have required a major development programme. Moreover, the bundle counters incorporate principles which apply to many unattended safeguards instruments. For example, concealing the operating status from potential diverters eases reliability specifications, continuous self-checking gives the inspector confidence in the readout, independence from continuous station services improves tamper-resistance, and the detailed data display provides tamper indication and a high level of credibility. Each irradiated fuel-bundle counter uses four Geiger counters to detect the passage of fuel bundles as they pass sequentially through the field-of-view. A microprocessor analyses the sequence of the Geiger counter signals and determines the number and direction of bundles transferred. The readout for IAEA inspectors includes both a tally and a printed log. The printer is also used to alert the inspector to abnormal fuel movements, tampering, Geiger counter failures and contamination of the fuel transfer mechanism. (author)

Post-irradiation examination of a fuel pin using a microscopic X-ray system: Measurement of carbon deposition and pin metrology

International Nuclear Information System (INIS)

Gras, Ch.; Stanley, S.J.

2008-01-01

The paper presents some interesting aspects associated with X-ray imaging and its potential application in the nuclear industry. The feasibility of using X-ray technology for the post-irradiation examination of a fuel pin has been explored, more specifically pin metrology and carbon deposition measurement. The non-active sample was specially designed to mimic the structure of an AGR fuel pin whilst a carbon based material was applied to the mock up fuel rod in order to mimic carbon deposition. Short duration low energy (50 kV) 2D digital radiography was employed and provided encouraging results (with respect to carbon deposition thickness and structure measurements) for the mock up fuel pin with a spatial resolution of around 10 μm. Obtaining quantitative data from the resultant images is the principal added value associated with X-ray imaging. A higher intensity X-ray beam (≥90 kV) was also used in conjunction with the low energy set-up to produce a clear picture of the cladding as well as the interface between the lead (Pb mimics the uranium oxide) and stainless steel cladding. Spent fuel metrology and routine radiography are two additional tasks that X-ray imaging could perform for the post-irradiation examination programme. Therefore, when compared to other techniques developed to deliver information on one particular parameter, X-ray imaging offers the possibility to extract useful information on a range of parameters

Specialists' meeting on theoretical modelling of LMFBR fuel pin behaviour. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-12-01

The purpose of the meeting was to provide an opportunity for exchanging views of theoretical modelling of LMFBR fuel pin behaviour and to summarise the IWGFR member countries' knowledge in this field. The special emphasis was placed on normal operating conditions. The technical part of the meeting was divided into six sessions, as follows: An overview of fuel modelling studies; Key factors and basic phenomena relevant to fuel pin behaviour modelling; Application to steady state operation and normal transients; Experimental validation through pins in service and specific irradiation experiments; Advanced fuels; and Brief review of existing codes. During the meeting, papers were presented by the delegates on behalf of their countries or organization. The papers, which are included in this report, were either in the form of a general survey of the subject, or on specific technical subjects. In each subject area presentations appropriate to the subject were made from the submitted papers. The presentations were followed by discussions of the questions raised and summary is made.

Specialists' meeting on theoretical modelling of LMFBR fuel pin behaviour. Summary report

International Nuclear Information System (INIS)

1979-12-01

The purpose of the meeting was to provide an opportunity for exchanging views of theoretical modelling of LMFBR fuel pin behaviour and to summarise the IWGFR member countries' knowledge in this field. The special emphasis was placed on normal operating conditions. The technical part of the meeting was divided into six sessions, as follows: An overview of fuel modelling studies; Key factors and basic phenomena relevant to fuel pin behaviour modelling; Application to steady state operation and normal transients; Experimental validation through pins in service and specific irradiation experiments; Advanced fuels; and Brief review of existing codes. During the meeting, papers were presented by the delegates on behalf of their countries or organization. The papers, which are included in this report, were either in the form of a general survey of the subject, or on specific technical subjects. In each subject area presentations appropriate to the subject were made from the submitted papers. The presentations were followed by discussions of the questions raised and summary is made

RANS-based CFD simulations of sodium fast reactor wire-wrapped pin bundles

International Nuclear Information System (INIS)

Pointer, W. D.; Thomas, J.; Fanning, T.; Fischer, P.; Siegel, A.; Smith, J.; Tokuhiro, A.

2009-01-01

In response to recent renewed interest in the development of advanced fast reactors, an effort is underway to develop a high-performance computational multi-physics simulation suite for the design and safety analysis of sodium cooled fast reactors. Within the multi-resolution thermal-hydraulics simulation component of this framework, high-resolution spectral large eddy simulation methods are used to improve turbulence models from coarser resolution Reynolds-averaged Navier-Stokes methods, and in turn, that data is used to improve or extend correlations used in traditional sub-channel tools. These ongoing studies provide the foundation for the development of the intermediate RANS-based resolution level. Prior work has focused on the benchmarking of flow field predictions on in 7-pin, 19-pin, and 37-pin fuel assemblies. The present work extends these studies to 217-pin assemblies in support of initial efforts to benchmark heat transfer predictions using the RANS models against conventional sub-channel models. In an effort to reduce the number of computational cells required to describe a 217-pin geometry, the effects of simplification of the geometric description of the contact point between the wire and the pin are investigated. The advantages of using polyhedral-based meshing methods rather than trimmed cell meshing methods have been demonstrated, and the effects of changes in axial mesh resolution in these meshes have been investigated. Results show that the geometric simplification has little impact on predicted flow fields, as does the use of a polyhedral mesh of comparable mesh density in place of the original trimmed cell mesh. While reducing axial mesh density has a notable impact on the velocity field, reducing predicted exchange velocities between adjacent subchannels by as much 25%, the impact on predicted temperature fields is negligible. (authors)

Synthesis Report on the understanding of failed LMFBR fuel element performance

International Nuclear Information System (INIS)

Plitz, H.; Bagley, K.; Harbourne, B.

1990-07-01

In the coarse of LMFBR operation fuel element failures cannot entirely be avoided as experienced during the operation of PFR, PHENIX and KNK II, where 44 failed fuel elements have been registered between 1978 and 1989. In earlier irradiations, post irradiation examinations showed mixed oxide pin diameter increases up to pin pitch distance, urging to stress reactor safety questions on the potential of fuel pin failure propagation within pin bundles. The chemical interaction of sodium with mixed oxide fuel is regarded to be the key for the understanding of failed fuel behavior. Valuable results on the failed fuel pin behavior during operation were obtained from the SILOE sodium loop test. Based on the bulk of experience with the detection of fuel pin failures, with the continued operation and with the handling of failed pins respectively elements, one can state: 1. All fuel pin failures have been detected securely in time and have been located. 2. Small defects are developing slowly. 3. Even large defects at end-of-life pins resulted in limited fuel loss. 4. Clad failures behave benign in main aspects. 5. The chemical interaction of sodium with mixed oxide is an important factor in the behavior of failed fuel pins, especially at high burnup. 6. Despite different pin designs and different operation conditions, on the basis of 44 failed elements in PFR, PHENIX and KNK II no pin-to-pin propagation was observed and fuel release was rather low, often not detectable. 7. In no case hazard conditions affecting reactor safety have been experienced

International Standard problem ISP 14: behaviour of a fuel bundle simulator during a specified heatup and flooding period (Rebeka experiment): results of post-test analyses: final comparison report

International Nuclear Information System (INIS)

Karwat, H.

1985-02-01

The test consisted in investigating the non-steady material behaviour of a bundle of electrically heated fuel rod simulators with respect to local fuel temperatures, cladding strain, time to burst and local strain at location of burst, together with the thermal hydraulic boundary conditions. The original aim has not been fully achievable. The applied codes for mechanical fuel behaviour largely demonstrated their capabilities for pretest predictions when certain local fluid dynamic parameters are well known to the code users. The difficulties expected with proper analysis of thermal hydraulics of the test were confirmed, caused by the coupling between pin cooling conditions, rod upper plenum calculations and the feedback to clad deformation and burst simulation

Critical experiments supporting underwater storage of tightly packed configurations of spent fuel pins. Technical progress report, January 1-March 31, 1981

International Nuclear Information System (INIS)

Hoovler, G.S.; Baldwin, M.N.

1981-04-01

Critical experiments are in progress on arrays of 2 1/2% enriched UO 2 fuel pins simulating underwater pin storage of spent power reactor fuel. Pin storage refers to a spent fuel storage concept in which the fuel assemblies are dismantled and the fuel pins are tightly packed into specially designed canisters. These experiments are providing benchmark data with which to validate nuclear codes used to design spent fuel pin storage racks

Input modelling of ASSERT-PV V2R8M1 for RUFIC fuel bundle

Energy Technology Data Exchange (ETDEWEB)

Park, Joo Hwan; Suk, Ho Chun

2001-02-01

This report describes the input modelling for subchannel analysis of CANFLEX-RU (RUFIC) fuel bundle which has been developed for an advanced fuel bundle of CANDU-6 reactor, using ASSERT-PV V2R8M1 code. Execution file of ASSERT-PV V2R8M1 code was recently transferred from AECL under JRDC agreement between KAERI and AECL. SSERT-PV V2R8M1 which is quite different from COBRA-IV-i code has been developed for thermalhydraulic analysis of CANDU-6 fuel channel by subchannel analysis method and updated so that 43-element CANDU fuel geometry can be applied. Hence, ASSERT code can be applied to the subchannel analysis of RUFIC fuel bundle. The present report was prepared for ASSERT input modelling of RUFIC fuel bundle. Since the ASSERT results highly depend on user's input modelling, the calculation results may be quite different among the user's input models. The objective of the present report is the preparation of detail description of the background information for input data and gives credibility of the calculation results.

Input modelling of ASSERT-PV V2R8M1 for RUFIC fuel bundle

International Nuclear Information System (INIS)

Park, Joo Hwan; Suk, Ho Chun

2001-02-01

This report describes the input modelling for subchannel analysis of CANFLEX-RU (RUFIC) fuel bundle which has been developed for an advanced fuel bundle of CANDU-6 reactor, using ASSERT-PV V2R8M1 code. Execution file of ASSERT-PV V2R8M1 code was recently transferred from AECL under JRDC agreement between KAERI and AECL. SSERT-PV V2R8M1 which is quite different from COBRA-IV-i code has been developed for thermalhydraulic analysis of CANDU-6 fuel channel by subchannel analysis method and updated so that 43-element CANDU fuel geometry can be applied. Hence, ASSERT code can be applied to the subchannel analysis of RUFIC fuel bundle. The present report was prepared for ASSERT input modelling of RUFIC fuel bundle. Since the ASSERT results highly depend on user's input modelling, the calculation results may be quite different among the user's input models. The objective of the present report is the preparation of detail description of the background information for input data and gives credibility of the calculation results

Lateral Flow Field Behavior Downstream of Mixing Vanes In a Simulated Nuclear Fuel Rod Bundle

International Nuclear Information System (INIS)

Conner, Michael E.; Smith, L. David III; Holloway, Mary V.; Beasley, Donald E.

2004-01-01

To assess the fuel assembly performance of PWR nuclear fuel assemblies, average subchannel flow values are used in design analyses. However, for this highly complex flow, it is known that local conditions around fuel rods vary dependent upon the location of the fuel rod in the fuel assembly and upon the support grid design that maintains the fuel rod pitch. To investigate the local flow in a simulated nuclear fuel rod bundle, a testing technique has been employed to measure the lateral flow field in a 5 x 5 rod bundle. Particle Image Velocimetry was used to measure the lateral flow field downstream of a support grid with mixing vanes for four unique subchannels in the 5 x 5 bundle. The dominant lateral flow structures for each subchannel are compared in this paper including the decay of these flow structures. (authors)

Axial gap formation in P.W.R. fuel pins

International Nuclear Information System (INIS)

Roberts, G.; Jones, K.W.

1978-07-01

The potential mechanisms of axial gap formation in PWR fuel pins are examined analytically and also using evidence from post-irradiation examination (p.i.e.) investigation. It is concluded that fuel and cladding cannot remain in contact during densification and so the settling of of the fuel stack, which forms the gaps, must be prevented by such things as asperities in the cladding, fuel chips or tilted pellets. Examples from the p.i.e. examination programme are used to support this conclusion. (author)

Nuclear reactor fuel element with a cluster of parallel fuel pins

International Nuclear Information System (INIS)

Macfall, D.; Butterfield, C.E.; Butterfield, R.S.

1977-01-01

An improvement of the design of nuclear reactor fuel elements is described and illustrated by the example of a gas-cooled, graphite-moderated nuclear reactor. The fuel element has a cluster of parallel fuel pins with an outer can of structure material and an inner sleeve, as well as tie bars and spacing devices for all of these parts. The fuel element designed according to the invention allows lasy assembling and disassembling before and after use. During use, no relative axial motions are possible; nevertheless, the graphite sleeve is at no time subject to tensile stress: the individual parts are held in position from below by a single holding device. (UWI) [de

Posttest examination of the VVER-1000 fuel rod bundle CORA-W2

International Nuclear Information System (INIS)

Sepold, L.

1995-06-01

The bundle meltdown experiment CORA-W2, representing the behavior of a Russian type VVER-1000 fuel element, with one B 4 C/stainless steel absorber rod was selected by the OECD/CSNI as International Standard Problem (ISP-36). The experimental results of CORA-W2 serve as data base for comparison with analytical predictions of the high-temperature material behavior by various code systems. The first part of the experimental results is described in KfK 5363 (1994), the second part is documented in this report which contains the destructive post-test examination results. The metallographical and analytical (SEM/EDX) post-test examinations were performed in Germany and Russia and are summarized in five individual contributions. The upper half of the bundle is completely oxidized, the lower half has kept the fuel rods relatively intact. The post-test examination results show the strong impact of the B 4 C absorber rod and the stainless steel grid spacers on the ''low-temperature'' bundle damage initiation and progression. The B 4 C absorber rod completely disappeared in the upper half of the bundle. The multicomponent melts relocated and formed coolant channel blockages on solidification with a maximum extent of about 30% in the lower part of the bundle. At temperatures above the melting point of the ZrNb1 cladding extensive fuel dissolution occurred. (orig.) [de

ASSERT-PV 3.2: Advanced subchannel thermalhydraulics code for CANDU fuel bundles

International Nuclear Information System (INIS)

Rao, Y.F.; Cheng, Z.; Waddington, G.M.; Nava-Dominguez, A.

2014-01-01

Highlights: • Introduction to a new version of the Canadian subchannel code, ASSERT-PV 3.2. • Enhanced models for flow-distribution, CHF and post-dryout heat transfer prediction. • Model changes focused on unique features of horizontal CANDU bundles. • Detailed description of model changes for all major thermalhydraulics models. • Discussion on rationale and limitation of the model changes. - Abstract: Atomic Energy of Canada Limited (AECL) has developed the subchannel thermalhydraulics code ASSERT-PV for the Canadian nuclear industry. The most recent release version, ASSERT-PV 3.2 has enhanced phenomenon models for improved predictions of flow distribution, dryout power and CHF location, and post-dryout (PDO) sheath temperature in horizontal CANDU fuel bundles. The focus of the improvements is mainly on modeling considerations for the unique features of CANDU bundles such as horizontal flows, small pitch to diameter ratios, high mass fluxes, and mixed and irregular subchannel geometries, compared to PWR/BWR fuel assemblies. This paper provides a general introduction to ASSERT-PV 3.2, and describes the model changes or additions in the new version to improve predictions of flow distribution, dryout power and CHF location, and PDO sheath temperatures in CANDU fuel bundles

ASSERT-PV 3.2: Advanced subchannel thermalhydraulics code for CANDU fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Rao, Y.F., E-mail: raoy@aecl.ca; Cheng, Z., E-mail: chengz@aecl.ca; Waddington, G.M., E-mail: waddingg@aecl.ca; Nava-Dominguez, A., E-mail: navadoma@aecl.ca

2014-08-15

Highlights: • Introduction to a new version of the Canadian subchannel code, ASSERT-PV 3.2. • Enhanced models for flow-distribution, CHF and post-dryout heat transfer prediction. • Model changes focused on unique features of horizontal CANDU bundles. • Detailed description of model changes for all major thermalhydraulics models. • Discussion on rationale and limitation of the model changes. - Abstract: Atomic Energy of Canada Limited (AECL) has developed the subchannel thermalhydraulics code ASSERT-PV for the Canadian nuclear industry. The most recent release version, ASSERT-PV 3.2 has enhanced phenomenon models for improved predictions of flow distribution, dryout power and CHF location, and post-dryout (PDO) sheath temperature in horizontal CANDU fuel bundles. The focus of the improvements is mainly on modeling considerations for the unique features of CANDU bundles such as horizontal flows, small pitch to diameter ratios, high mass fluxes, and mixed and irregular subchannel geometries, compared to PWR/BWR fuel assemblies. This paper provides a general introduction to ASSERT-PV 3.2, and describes the model changes or additions in the new version to improve predictions of flow distribution, dryout power and CHF location, and PDO sheath temperatures in CANDU fuel bundles.

Design, fabrication, and operation of capsules for the irradiation testing of candidate advanced space reactor fuel pins

International Nuclear Information System (INIS)

Thoms, K.R.

1975-04-01

Fuel irradiation experiments were designed, built, and operated to test uranium mononitride (UN) fuel clad in tungsten-lined T-111 (Ta-8 percent W-2 percent Hf) and uranium dioxide (UO 2 ) fuel clad in both tungsten-lined T-111 and tungsten-lined Nb-1 percent Zr. A total of nine fuel pins was irradiated (four containing porous UN, two containing dense, nonporous UN, and three containing dense UO 2 ) at average cladding temperatures ranging from 931 to 1015 0 C. The UN experiments, capsules UN-4 and -5, operated for 10,480 and 10,037 hr, respectively, at an average linear heat generation rate of 10 kW/ft. The UO 2 experiment, capsule UN-6, operated for 8333 hr at an average linear heat generation rate of approximately 5 kW/ft. Following irradiation, the nine fuel pins were removed from their capsules, externally examined, and sent to the NASA Plum Brook Facility for more detailed postirradiation examination. During visual examination, it was discovered that the cladding of the fuel pin containing dense UN in each of capsules UN-4 and -5 had failed, exposing the UN fuel to the NaK in which the pins were submerged and permitting the release of fission gas from the failed pins. A rough analysis of the fission gas seen in samples of the gas in the fuel pin region indicated fission gas release-to-birth rates from these fuel pins in the range of 10 -5 . (U.S.)

Assembly mechanism for nuclear fuel bundles

International Nuclear Information System (INIS)

Long, J.W.; Flora, B.S.

1977-01-01

A method of securing a fuel bundle to permit easy remote disassembly is described. Fuel rods are held loosely between end plates, each end of the rods fitting into holes in the end plates. At the upper end of each fuel rod there is a spring pressing against the end plate. Tie rods are used to hold the end plates together securely. The lower end of each tie rod is screwed into the lower end plate; the upper end of each tie rod is attached to the upper end plate by means of a locking assembly described in the patent. In order to remove the upper tie plate during the disassembly process, it is necessary only to depress the tie plate against the pressure of the springs surrounding the fuel rods and then to rotate each locking sleeve on the tie rods from its locked to its unlocked position. It is then possible to remove the tie plate without disassembling the locking assembly. (LL)

High burnup, high power irradiation behavior of helium-bonded mixed carbide fuel pins

International Nuclear Information System (INIS)

Levine, P.J.; Nayak, U.P.; Boltax, A.

1983-01-01

Large diameter (9.4 mm) helium-bonded mixed carbide fuel pins were successfully irradiated in EBR-II to high burnup (12%) at high power levels (100 kW/m) with peak cladding midwall temperatures of 550 0 C. The wire-wrapped pins were clad with 0.51-mm-thick, 20% cold-worked Type 316 stainless steel and contained hyperstoichiometric (Usub(0.8)Pusub(0.2))C fuel covering the smeared density range from 75-82% TD. Post-irradiation examinations revealed: extensive fuel-cladding mechanical interaction over the entire length of the fuel column, 35% fission gas release at 12% burnup, cladding carburization and fuel restructuring. (orig.)

Investigations with diagnostic fuel rod bundles on Rheinsberg NPP

International Nuclear Information System (INIS)

Krauze, F.; Rudolf, G.; Shajfler, V.; Tsimke, K.

1982-01-01

In 70MW pressurized water reactor of Rheinsberg NPP diagnostic fuel rod bundles have been installed: first of DK 1 type and then of DK 2 advanced type. Three rounds of measurement were run with DK 1 bundle and one with DK 2. The diagnostic bundles are equiped with various sensors for temperature, pressure, neutron flux and mechanical stress measurements as well as with special flow rate control system which allows to reach coolant boiling within the bundle. Qualitative and quantitative description of the sensors performance during reactor operation is given. The presented experimental results are connected with: 1) working capability of the measuring devices and their calibration; 2) throttling and boiling in two regimes: a) stationary and non-stationary flow rate throbgh DK during stationary reactor operation; b) various constant levels of flow rate through DK during non-stationary reactor operation regime [ru

Fabrication drawings of fuel pins for FUJI project among PSI, JNC and NRG. Revised version 2

International Nuclear Information System (INIS)

Ozawa, Takayuki; Nakazawa, Hiroaki; Abe, Tomoyuki; Nagayama, Masahiro

2002-10-01

Irradiation tests and post-irradiation examinations in the framework of JNC-PSI-NRG collaboration project will be performed in 2003-2005. Irradiation fuel pins will be fabricated by the middle of 2003. The fabrication procedure for irradiation fuel pins has been started in 2001. Several fabrication tests and qualification tests in JNC and PSI (Paul Scherrer Institut, Switzerland) have been performed before the fuel pin fabrication. According to the design assignment between PSI and JNC in the frame of this project, PSI should make specification documents for the fuel pellet, the sphere-pac fuel particles, the vipac fuel fragments, and the fuel segment fabrication. JNC should make the fabrication drawings for irradiation pins. JNC has been performed the fuel design in cooperation with PSI and NRG (Nuclear Research and Consultancy Group, Holland). In this project, the pelletized fuel, the sphere-pac fuel, and the vipac fuel will be simultaneously irradiated on HFR (High Flux Reactor, Holland). The fabrication drawings have been made under the design assignment with PSI, and consist of the drawings of MOX pellet, thermal insulator pellet, pin components, fuel segments, and the constructed pin. The fabrication drawings were approved in October 2001, but after that, the optimization of specifications was discussed and agreed among all partners. According to this agreement, the fabrication drawings were revised in January 2002. After the earlier revision, the shape of particle retainer to be made by PSI was modified from its drawing beforehand delivered. In this report, the fabrication drawings revised again will be shown, and the fabrication procedure (welding Qualification Tests) will be modified in accordance with the result of discussion on the 3rd technical meeting held in September 2002. These design works have been performed in Fuel Design and Evaluation Group, Plutonium Fuel Fabrication Division, Plutonium Fuel Center under the commission of Plutonium Fuel

Element bow profiles from new and irradiated CANDU fuel bundles

International Nuclear Information System (INIS)

Dennier, D.; Manzer, A.M.; Ryz, M.A.

1996-01-01

Improved methods of measuring element profiles on new CANDU fuel bundles were developed at the Sheridan Park Engineering Laboratory, and have now been applied in the hot cells at Whiteshell Laboratories. For the first time, the outer element profiles have been compared between new, out-reactor tested, and irradiated fuel elements. The comparison shows that irradiated element deformation is similar to that observed on elements in out-reactor tested bundles. In addition to the restraints applied to the element via appendages, the element profile appears to be strongly influenced by gravity and the end loads applied by local deformation of the endplate. Irradiation creep in the direction of gravity also tends to be a dominant factor. (author)

Thermochemical aspects of fuel-cladding and fuel-coolant interactions in LMFBR oxide fuel pins

International Nuclear Information System (INIS)

Adamson, M.G.; Aitken, E.A.; Caputi, R.W.; Potter, P.E.; Mignanelli, M.A.

1979-01-01

This paper examines several thermochemical aspects of the fuel-cladding, fuel-coolant and fuel-fission product interactions that occur in LMFBR austenitic stainless steel-clad mixed (U,Pu)-oxide fuel pins during irradiation under normal operating conditions. Results are reported from a variety of high temperature EMF cell experiments in which continuous oxygen activity measurements on reacting and equilibrium mixtures of metal oxides and (excess) liquid alkali metal (Na, K, Cs) were performed. Oxygen potential and 0:M thresholds for Na-fuel reactions are re-evaluated in the light of new measurements and newly-assessed thermochemical data, and the influence on oxygen potential of possible U-Pu segregation between oxide and urano-plutonate (equilibrium) phases has been analyzed. (orig./RW) [de

The Key-Role of shielding analysis in advanced Candu Fuel bundles nuclear safety improvement for some accidental criticality scenarios

International Nuclear Information System (INIS)

Margeanu, C.A.; Rizoiu, A.; Olteanu, G.

2008-01-01

The paper aims to present the source term and photon dose rates estimation for advanced Candu fuel bundles in some accidental criticality scenarios. As reference, the Candu standard fuel bundle has been used. The scenarios take into account for a very short-time irradiated or spent fuel bundles for some configurations closed to criticality. In order to estimate irradiated fuel characteristic parameters and radiation doses, the ORNL's SCALE 5 codes Origin-S and Monte Carlo MORSE-SGC have been used. The paper includes the irradiated fuel characteristic parameters comparison for the considered Candu fuel bundles, providing also a comparison between the corresponding radiation doses

Input modelling of ASSERT-PV V2R8M1 for RUFIC fuel bundle

Energy Technology Data Exchange (ETDEWEB)

Park, Joo Hwan; Suk, Ho Chun

2001-02-01

This report describes the input modelling for subchannel analysis of CANFLEX-RU (RUFIC) fuel bundle which has been developed for an advanced fuel bundle of CANDU-6 reactor, using ASSERT-PV V2R8M1 code. Execution file of ASSERT-PV V2R8M1 code was recently transferred from AECL under JRDC agreement between KAERI and AECL. SSERT-PV V2R8M1 which is quite different from COBRA-IV-i code has been developed for thermalhydraulic analysis of CANDU-6 fuel channel by subchannel analysis method and updated so that 43-element CANDU fuel geometry can be applied. Hence, ASSERT code can be applied to the subchannel analysis of RUFIC fuel bundle. The present report was prepared for ASSERT input modelling of RUFIC fuel bundle. Since the ASSERT results highly depend on user's input modelling, the calculation results may be quite different among the user's input models. The objective of the present report is the preparation of detail description of the background information for input data and gives credibility of the calculation results.

Calculation of Heat-Bearing Agent’s Steady Flow in Fuel Bundle

Science.gov (United States)

Amosova, E. V.; Guba, G. G.

2017-11-01

This paper introduces the result of studying the heat exchange in the fuel bundle of the nuclear reactor’s fuel magazine. The article considers the fuel bundle of the infinite number of fuel elements, fuel elements are considered in the checkerboard fashion (at the tops of a regular triangle a fuel element is a plain round rod. The inhomogeneity of volume energy release in the rod forms the inhomogeneity of temperature and velocity fields, and pressure. Computational methods for studying hydrodynamics in magazines and cores with rod-shape fuel elements are based on a significant simplification of the problem: using basic (averaged) equations, isobaric section hypothesis, porous body model, etc. This could be explained by the complexity of math description of the three-dimensional fluid flow in the multi-connected area with the transfer coefficient anisotropy, curved boundaries and technical computation difficulties. Thus, calculative studying suggests itself as promising and important. There was developed a method for calculating the heat-mass exchange processes of inter-channel fuel element motions, which allows considering the contribution of natural convection to the heat-mass exchange based on the Navier-Stokes equations and Boussinesq approximation.

Fuel-cladding chemical interaction correlation for mixed-oxide fuel pins

International Nuclear Information System (INIS)

Lawrence, L.A.

1986-10-01

A revised wastage correlation was developed for FCCI with fabrication and operating parameters. The expansion of the data base to 305 data sets provided sufficient data to employ normal statistical techniques for calculation of confidence levels without unduly penalizing predictions. The correlation based on 316 SS cladding also adequately accounts for limited measured depths of interaction for fuel pins with D9 and HTq cladding

Accuracy of dimension measurements from neutron radiographs of nuclear fuel pins

International Nuclear Information System (INIS)

Domanus, J.C.

1976-01-01

A comparison is given of accuracies obtained with measuring the dimensions (pellet diameter and fuel-clad gap) from neutron and X-ray radiographs of a calibrated nuclear fuel pin performed with a projection microscope, microdensitometers and a video micrometer

Pressure drop ana velocity measurements in KMRR fuel rod bundles

International Nuclear Information System (INIS)

Yagn, Sun Kyu; Chung, Heung June; Chung, Chang Whan; Chun, Se Young; Song, Chul Wha; Won, Soon Yeun; Chung, Moon Ki

1990-01-01

The detailed hydraulic characteristic measurements in subchannels of longitudinally finned rod bundles using one-component LDV(Laser Doppler Velocimeter) were performed. Time mean axial velocity, turbulent intensity, and turbulent micro scales, such as time auto-correlation, Eulerian integral and micro scale, Kolmogorov length and time scale, and Taylor micro length scale were measured. The signals from LDV are inherently more or less discontinuous. The spectra of signals having such intermittent defects can be obtained by the fast Fourier transformation (FFT) of the auto-correlation function. The turbulent crossflow mixing rate between neighboring subchannels and dominant frequencies were evaluated from the measured data. Pressure drop data were obtained for the typical 36-element and 18-element fuel rod bundles fabricated by the design requirement of KMRR fuel and for other type of fuels assembled with 6-fin rods to investigate the fin effects on the pressure drop characteristics

CAT reconstruction and potting comparison of a LMFBR fuel bundle

International Nuclear Information System (INIS)

Betten, P.R.; Tow, D.M.

1984-04-01

A standard Liquid Metal Fast Breeder Reactor (LMFBR) subassembly used in the Experimental Breeder Reactor II (EBR-II) was investigated, by remote techniques, for fuel bundle distortion by both nondestructive and destructive methods, and the results from both methods were compared. The non-destructive method employed neutron tomography to reconstruct the locations of fuel elements through the use of a maximum entropy reconstruction algorithm known as MENT. The destructive method consisted of ''potting'' (a technique that embeds and permanently fixes the fuel elements in a solid matrix) the subassembly, and then cutting and polishing the individual sections. The comparison indicated that the tomography reconstruction provided good results in describing the bundle geometry and spacer-wire locations, with the overall resolution being on the order of a spacer-wire diameter. A dimensional consistency check indicated that the element and spacer-wire dimensions were accurately reproduced in the reconstruction

Preliminary evaluation of pin power distribution for fuel assemblies of SMART by MCNP

International Nuclear Information System (INIS)

Kim, Kyo Youn

1998-08-01

Monte Carlo transport code MCNP can describe an object sophisticately by use of three-dimensional modelling and can adopt a continuous energy cross-section library. Therefore MCNP has been widely utilized in the field of radiation physics to estimate fluxes and dose rates for nuclear facilities and to review results from conventional methods such a as discrete ordinates method and point kernel method. The Monte Carlo method has recently been introduced to estimated the neutron multiplication factor and pin power distribution in the fuel assembly of a reactor core. The operating thermal power of SMART core is 330 MWt and there are 57 fuel assemblies in the core. In this study it was assumed that the core has 4 types of fuel assemblies. In this study, MCNP4a was used to perform to estimate criticality and normalized pin power distribution in a fuel assembly of SMART core. The results from MCNP4a calculations are able to be used review those from nuclear design/analysis code. It is very complicated to pick up interested data from MCNP output list and to normalize pin power distribution in a fuel assembly because MCNP is not only a nuclear design/analysis code. In this study a program FAPIN was developed to generated a generate a normalized pin power distribution from the MCNP output list. (author). 11 refs

Effects of fuel relocation on reflood in a partially-blocked rod bundle

Energy Technology Data Exchange (ETDEWEB)

Kim, Byoung Jae [School of Mechanical Engineering, Chungnam National University, 99 Daehak-ro, Yuseong-gu, Daejeon 34134 (Korea, Republic of); Kim, Jongrok; Kim, Kihwan; Bae, Sung Won [Thermal-Hydraulic Safety Research Division, Korea Atomic Energy Research Division, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of); Moon, Sang-Ki, E-mail: skmoon@kaeri.re.kr [Thermal-Hydraulic Safety Research Division, Korea Atomic Energy Research Division, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of)

2017-02-15

Ballooning of the fuel rods has been an important issue, since it can influence the coolability of the rod bundle in a large-break loss-of-coolant accident (LBLOCA). Numerous past studies have investigated the effect of blockage geometry on the heat transfer in a partially blocked rod bundle. However, they did not consider the occurrence of fuel relocation and the corresponding effect on two-phase heat transfer. Some fragmented fuel particles located above the ballooned region may drop into the enlarged volume of the balloon. Accordingly, the fuel relocation brings in a local power increase in the ballooned region. The present study’s objective is to investigate the effect of the fuel relocation on the reflood under a LBLOCA condition. Toward this end, experiments were performed in a 5 × 5 partially-blocked rod bundle. Two power profiles were tested: one is a typical cosine shape and the other is the modified shape considering the effect of the fuel relocation. For a typical power shape, the peak temperature in the ballooned rods was lower than that in the intact rods. On the other hand, for the modified power shape, the peak temperature in the ballooned rods was higher than that in the intact rods. Numerical simulations were also performed using the MARS code. The tendencies of the peak clad temperatures were well predicted.

COXPRO-II: a computer program for calculating radiation and conduction heat transfer in irradiated fuel assemblies

International Nuclear Information System (INIS)

Rhodes, C.A.

1984-12-01

This report describes the computer program COXPRO-II, which was written for performing thermal analyses of irradiated fuel assemblies in a gaseous environment with no forced cooling. The heat transfer modes within the fuel pin bundle are radiation exchange among fuel pin surfaces and conduction by the stagnant gas. The array of parallel cylindrical fuel pins may be enclosed by a metal wrapper or shroud. Heat is dissipated from the outer surface of the fuel pin assembly by radiation and convection. Both equilateral triangle and square fuel pin arrays can be analyzed. Steady-state and unsteady-state conditions are included. Temperatures predicted by the COXPRO-II code have been validated by comparing them with experimental measurements. Temperature predictions compare favorably to temperature measurements in pressurized water reactor (PWR) and liquid-metal fast breeder reactor (LMFBR) simulated, electrically heated fuel assemblies. Also, temperature comparisons are made on an actual irradiated Fast-Flux Test Facility (FFTF) LMFBR fuel assembly

Modernization of RTC for fabrication of MOX fuel, Vibropac fuel pins and BN-600 FA with weapon grade plutonium

International Nuclear Information System (INIS)

Grachyov, A.F.; Kalygin, V.V.; Skiba, O.V.; Mayorshin, A. A.; Bychkov, A.V.; Kisly, V.A.; Ovsyannikov, Y.F.; Bobrov, D.A.; Mamontov, S.I.; Tsyganov, A.N.; Churutkin, E.I.; Davydov, P.I.; Samosenko, E.A; Shalak, A.R.; Ojima, Hisao

2004-01-01

Since mid 70's RIAR has been performing activities on plutonium involvement in fuel cycle. These activities are considered a stage within the framework of the closed fuel cycle development. Developed at RIAR fuel cycle is based on two technologies: 'dry' process of fuel reprocessing and vibro-packing method for fuel pin fabrication. Due to the available scientific capabilities and a gained experience in operating the technological facilities (ORYOL, SIC) for plutonium (various grade) blending into fuel for fast reactors, RIAR is a participant of the activities aimed at solving these tasks. Under international program RIAR with financial support of JNC (Japan) is modernizing the facility for granulated fuel production, vibro-pac fuel pins and FA fabrication to provide the BN-600 'hybrid' core. In order to provide 'hybrid' core it is necessary to produce (per year): - 1775 kg of granulated MOX-fuel, 6500 fuel pins, 50 fuel assemblies. Potential output of the facility under construction is as follows: - 1800 kg of granulated MOX-fuel per year, 40 fuel pins per shift, 200 FAs for the BN-600 reactor per year. Taking into account domestic and foreign experience in MOX-fuel production, different options were discussed of the equipment layouts in the available premises of chemical technological division of RIAR: - in the shielded manipulator boxes, in the existing hot cells. During construction of the facility in the building under operation the following requirements should be met: - facility must meet all standards and regulations set for nuclear facilities, installation work at the facility must not influence other production programs implemented in the building, engineering supply lines of the facility must be connected to the existing service lines of the building, cost of the activities must not exceed amount of JNC funding. The paper presents results of comparison between two options of the process equipment layout: in boxes and hot cells. This equipment is intended

Modelling disassembled fuel bundles using CATHENA MOD-3.5a under LOCA/LOECC conditions

Energy Technology Data Exchange (ETDEWEB)

Lei, Q M; Sanderson, D B; Dutton, R [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs.

1996-12-31

CATHENA MOD-3.5a is a multipurpose thermalhydraulic computer code developed primarily to analyse postulated loss-of-coolant scenarios for CANDU nuclear reactors. The code contains a generalized heat transfer package that enables it to model the behaviour of a fuel channel in great detail. Throughout the development of the CATHENA code, considerable effort has been devoted to evaluating, validating and documenting its overall capability as a design and safety assessment tool. Specific attention has focused on its ability to predict fuel channel behaviour under postulated accident conditions. This paper describes an investigation of CATHENA`s ability to predict the thermal-chemical responses of a fuel channel in which the 37-element bundles were assumed to disassemble and rearrange into a closed-packed stack of elements at the bottom of the pressure tube. A representative disassembled bundle geometry was modelled during a simulated loss-of-coolant accident scenario using CATHENA MOD-3.5a/Rev 0, with superheated steam being the only coolant available. Thermal conduction in the radial and circumferential directions was calculated for individual fuel elements, the pressure tube, and the calandria tube. Radiation view factors for the intact and disassembled bundle geometries were calculated using a CATHENA utility program. Inter-element metal-to-metal contact was accounted for using the CATHENA solid-solid contact model. An offset pressure-tube configuration, representing a partially sagged pressure tube, and the effect of steam starvation on the exothermic zirconium-steam reaction, were included in the CATHENA model. The CATHENA-predicted results show a dramatic suppression of heat generation from the zirconium-steam reaction when bundle disassembly is initiated. The predicted results show a smaller temperature increase in the fuel sheaths and the pressure tube for the disassembled bundle geometry, compared to the temperature excursion for the intact bundle. (author

DESIGN OF WIRE-WRAPPED ROD BUNDLE MATCHED INDEX-OF-REFRACTION EXPERIMENTS

Energy Technology Data Exchange (ETDEWEB)

Hugh McIlroy; Hongbin Zhang; Kurt Hamman

2008-05-01

Experiments will be conducted in the Idaho National Laboratory (INL) Matched Index-of-Refraction (MIR) Flow Facility [1] to characterize the three-dimensional velocity and turbulence fields in a wire-wrapped rod bundle typically employed in liquid-metal cooled fast reactors and to provide benchmark data for computer code validation. Sodium cooled fast reactors are under consideration for use in the U.S. Department of Energy (DOE) Global Nuclear Energy Partnership (GNEP) program. The experiment model will be constructed of quartz components and the working fluid will be mineral oil. Accurate temperature control (to within 0.05 oC) matches the index-of-refraction of mineral oil with that of quartz and renders the model transparent to the wavelength of laser light employed for optical measurements. The model will be a scaled 7-pin rod bundle enclosed in a hexagonal canister. Flow field measurements will be obtained with a LaVision 3-D particle image velocimeter (PIV) and complimented by near-wall velocity measurements obtained from a 2-D laser Doppler velocimeter (LDV). These measurements will be used as benchmark data for computational fluid dynamics (CFD) validation. The rod bundle model dimensions will be scaled up from the typical dimensions of a fast reactor fuel assembly to provide the maximum Reynolds number achievable in the MIR flow loop. A range of flows from laminar to fully-turbulent will be available with a maximum Reynolds number, based on bundle hydraulic diameter, of approximately 22,000. The fuel pins will be simulated by 85 mm diameter quartz tubes (closed on the inlet ends) and the wire-wrap will be simulated by 25 mm diameter quartz rods. The canister walls will be constructed from quartz plates. The model will be approximately 2.13 m in length. Bundle pressure losses will also be measured and the data recorded for code comparisons. The experiment design and preliminary CFD calculations, which will be used to provide qualitative hydrodynamic

DANCOFF-MC: A program to calculate Dancoff factors in CANDU type fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Feher, S; Valko, J

1992-12-01

The objective of DANCOFF-MC is the evaluation of Dancoff factors for cylindrical fuel rods arranged parallel in various and complicated bundle geometries. No interaction with fuel rods in any of the other bundles are considered due to the large distance, in mean free paths, between the buldes. Using a common basic algorithm three versions of the program have been written so far: The DANCOFF-MC-2, the DANCOFF-MC-19 and the DANCOFF-MC-27. (orig./HP).

Breached fuel pin contamination from Run Beyond Cladding Breach (RBCB) tests in EBR-II

International Nuclear Information System (INIS)

Colburn, R.P.; Strain, R.V.; Lambert, J.D.B.; Ukai, S.; Shibahara, I.

1988-09-01

Studies indicate there may be a large economic incentive to permit some continued reactor operation with breached fuel pin cladding. A major concern for this type of operation is the potential spread of contamination in the primary coolant system and its impact on plant maintenance. A study of the release and transport of contamination from naturally breached mixed oxide Liquid Metal Reactor (LMR) fuel pins was performed as part of the US Department of Energy/Power Reactor and Nuclear Fuel Development Corporation (DOE/PNC) Run Beyond Cladding Breach (RBCB) Program at EBR-II. The measurements were made using the Breached Fuel Test Facility (BFTF) at EBR-II with replaceable deposition samplers located approximately 1.5 meters from the breached fuel test assemblies. The effluent from the test assemblies containing the breached fuel pins was routed up through the samplers and past dedicated instrumentation in the BFTF before mixing with the main coolant flow stream. This paper discusses the first three contamination tests in this program. 2 refs., 5 figs., 2 tabs

Assessment of pin-by-pin fission rate distribution within MOX/UO{sub 2} fuel assembly using MCNPX code

Energy Technology Data Exchange (ETDEWEB)

Louis, Heba Kareem; Amin, Esmat [Nuclear and Radiological Regulation Authority (NRRA), Cairo (Egypt). Safety Engineering Dept.

2016-03-15

The aim of the present paper is to assess the calculations of pin-by-pin group integrated fission rates within MOX/UO{sub 2} Fuel assemblies using the Monte Carlo code MCNP2.7c with two sets of the available latest nuclear data libraries used for calculating MOX-fueled systems. The data that are used in this paper are based on the benchmark by the NEA Nuclear Science Committee (NSC). The k{sub ∞} and absorption/fission reaction rates per isotope, k{sub eff} and pin-by-pin group integrated fission rates on 1/8 fraction of the geometry are determined. To assess the overall pin-by-pin fission rate distribution, the collective per cent error measures were investigated. The results of AVG, MRE and RMS error measures were less than 1 % error. The present results are compared with other participants using other Monte Carlo codes and with CEA results that were taken in the benchmark as reference. The results with ENDF/B-VI.6 are close to the results received by MVP (JENDL3.2) and SCALE 4.2 (JEF2.2). The results with ENDF/BVII.1 give higher values of k{sub ∞} reflecting the changes in the newer evaluations. In almost all results presented here, the MCNP calculated results with ENDF/B VII.1 should be considered more than those obtained by using other Monte Carlo codes and nuclear data libraries. The present calculations may be consider a reference for evaluating the numerical schemes in production code systems, as well as the global performance including cross-section data reduction methods as the calculations used continuous energy and no geometrical approximations.

THEBES: a thermal hydraulic code for the calculation of transient two phase flow in bundle geometry

International Nuclear Information System (INIS)

Camous, F.

1983-01-01

The three dimensional thermal hydraulic code THEBES, capable to calculate transient boiling of sodium in rod bundles is described here. THEBES, derived from the transient single phase code SABRE-2A, was developed in CADARACHE by the SIES to analyse the SCARABEE N loss of flow experiments. This paper also presents the results of tests which were performed against various types of experiments: (1) transient boiling in a 7 pin bundle simulating a partial blockage at the bottom of a subassembly (rapid transient SCARABEE 7.2 experiment), (2) transient boiling in a 7 pin bundle simulating a coolant coast down (slow transient SCARABEE 7.3 experiment), (3) steady local and generalised boiling in a 19 pin bundle (GR 19 I experiment), (4) transient boiling in a 19 pin bundle simulating a coolant coast down (GR 19 I experiment), (5) steady local boiling in a 37 pin bundle with internal blockage (MOL 7C experiment). Excellent agreement was found between calculated and experimental results for these different situations. Our conclusion is that THEBES is able to calculate transient boiling of sodium in rod bundles in a quite satisfying way

Pressure drop variation as a function of axial and radial power distribution in CANDU fuel channel with standard and CANFLEX 43 bundles

International Nuclear Information System (INIS)

Catana, Alexandru; Department of Energy Danila, Nicolae; Prisecaru, Ilie; Dupleac, Daniel

2007-01-01

CANDU 600 nuclear reactors are usually fuelled with STANDARD (STD), 37 rods fuel bundles. Natural uranium (NU) dioxide (UO 2 ), is used as fuel composition. A new fuel bundle geometry called CANFLEX (CFX) with 43 rods is proposed and some new fuel composition are considered. Flexibility is the key word for the attempt to use some different fuel geometries and compositions for CANDU 600 nuclear reactors as well as for innovative ACR-700/1000 nuclear reactors. The fuel bundle considered in this paper is CFX-RU-0.90 that encodes the CANFLEX geometry, recycled dioxide uranium (RU) with 0.90% enrichment. The goal of this proposal is ambitious: a higher average discharge burn-up up to 14000 MWd/tU and, for the same amount of generated electric power, reduction in nuclear fuel fabrication, reduction of spent nuclear fuel radioactive waste and reduction of refueling operational work by using fewer bundles. An improved sub-channel approach for thermal-hydraulic analysis is used in this paper to compute some flow parameters, mainly the pressure drop along the CANDU 600 fuel channel when STD or CFX-RU-0.90 fuel bundles. Also an intermediate CFX-NU fuel bundle are used, for gradual comparison. For CFX-RU- 0.90 four fuel bundle shift refueling scheme is used instead of eight, that will determine different axial power distributions. At the same time radial power distribution is affected by the geometry and by the fuel composition of fuel bundle type used. Some other thermal-hydraulic flow parameters will be influenced, too. One of the most important parameter is pressure drop (PD) along the fuel channel because of its importance in drag force evaluation. We start with an axial power distribution, which is characteristic for a refueling scheme of eight or four fuel bundles on a shift. Comparative results are presented between STD37, CFX-NU CFX-RU-0.90 fuel bundles in a CANDU nuclear reactor operating conditions. Neutron flux distribution analysis shows that four bundle shift

Experimental and numerical investigations of BWR fuel bundle inlet flow

International Nuclear Information System (INIS)

Hoashi, E; Morooka, S; Ishitori, T; Komita, H; Endo, T; Honda, H; Yamamoto, T; Kato, T; Kawamura, S

2009-01-01

We have been studying the mechanism of the flow pattern near the fuel bundle inlet of BWR using both flow visualization test and computational fluid dynamics (CFD) simulation. In the visualization test, both single- and multi-bundle test sections were used. The former test section includes only a corner orifice facing two support beams and the latter simulates 16 bundles surrounded by four beams. An observation window is set on the side of the walls imitating the support beams upstream of the orifices in both test sections. In the CFD simulation, as well as the visualization test, the single-bundle model is composed of one bundle with a corner orifice and the multi-bundle model is a 1/4 cut of the test section that includes 4 bundles with the following four orifices: a corner orifice facing the corner of the two neighboring support beams, a center orifice at the opposite side from the corner orifice, and two side orifices. Twin-vortices were observed just upstream of the corner orifice in the multi-bundle test as well as the single-bundle test. A single-vortex and a vortex filament were observed at the side orifice inlet and no vortex was observed at the center orifice. These flow patterns were also predicted in the CFD simulation using Reynolds Stress Model as a turbulent model and the results were in good agreement with the test results mentioned above. (author)

Measurement and CFD calculation of spacer loss coefficient for a tight-lattice fuel bundle

International Nuclear Information System (INIS)

In, Wang Kee; Shin, Chang Hwan; Kwack, Young Kyun; Lee, Chi Young

2015-01-01

Highlights: • Experiment and CFD analysis evaluated the pressure drop in a spacer grid. • The measurement and CFD errors for the spacer loss coefficient were estimated. • The spacer loss coefficient for the dual-cooled annular fuel bundle was determined. • The CFD prediction agrees with the measured spacer loss coefficient within 8%. - Abstract: An experiment and computational fluid dynamics (CFD) analysis were performed to evaluate the pressure drop in a spacer grid for a dual-cooled annular fuel (DCAF) bundle. The DCAF bundle for the Korean optimum power reactor (OPR1000) is a 12 × 12 tight-lattice rod array with a pitch-to-diameter ratio of 1.08 owing to a larger outer diameter of the annular fuel rod. An experiment was conducted to measure the pressure drop in spacer grid for the DCAF bundle. The test bundle is a full-size 12 × 12 rod bundle with 11 spacer grid. The test condition covers a Reynolds number range of 2 × 10 4 –2 × 10 5 by changing the temperature and flow rate of water. A CFD analysis was also performed to predict the pressure drop through a spacer grid using the full-size and partial bundle models. The pressure drop and loss coefficient of a spacer grid were predicted and compared with the experimental results. The CFD predictions of spacer pressure drop and loss coefficient agree with the measured values within 8%. The spacer loss coefficient for the DCAF bundle is estimated to be approximately 1.50 at a nominal operating condition of OPR1000, i.e., Re = 4 × 10 5

The deformation analysis of the KALIMER breakeven core driver fuel pin based on the axial power profile during irradiation

International Nuclear Information System (INIS)

Lee, Dong Uk; Lee, Byoung Oon; Kim, Young Kyun; Hong, Ser Gi; Chang, Jin Wook; Lee, Ki Bok; Kim, Young Il

2003-03-01

In this study, material properties such as coolant specific heat, film heat transfer coefficient, cladding thermal conductivity, surface diffusion coefficient of the multi-bubble are improved in MACSIS-Mod1. The axial power and flux profile module was also incorporated with irradiation history. The performance and feasibility of the driver fuel pin have been analyzed for nominal parameters based on the conceptual design for the KALIMER breakeven core by MACSIS-MOD1 code. The fuel slug centerline temperature takes the maximum at 700mm from the bottom of the slug in spite of the nearly symmetric axial power distribution. The cladding mid-wall and coolant temperatures take the maximum at the top of the pin. Temperature of the fuel slug surface over the entire irradiation life is much lower than the fuel-clad eutectic reaction temperature. The fission gas release of the driver fuel pin at the End Of Life(EOL) is predicted to be 68.61% and plenum pressure is too low to cause cladding yielding. The probability that the fuel pin would fail is estimated to be much less than that allowed in the design criteria. The maximum radial deformation of the fuel pin is 1.928%, satisfying the preliminary design criterion (3%) for fuel pin deformation. Therefore the conceptual design parameters of the driver fuel pin for the KALIMER breakeven core are expected to satisfy the preliminary criteria on temperature, fluence limit, deformation limit etc

The deformation analysis of the KALIMER breakeven core driver fuel pin based on the axial power profile during irradiation

Energy Technology Data Exchange (ETDEWEB)

Lee, Dong Uk; Lee, Byoung Oon; Kim, Young Kyun; Hong, Ser Gi; Chang, Jin Wook; Lee, Ki Bok; Kim, Young Il

2003-03-01

In this study, material properties such as coolant specific heat, film heat transfer coefficient, cladding thermal conductivity, surface diffusion coefficient of the multi-bubble are improved in MACSIS-Mod1. The axial power and flux profile module was also incorporated with irradiation history. The performance and feasibility of the driver fuel pin have been analyzed for nominal parameters based on the conceptual design for the KALIMER breakeven core by MACSIS-MOD1 code. The fuel slug centerline temperature takes the maximum at 700mm from the bottom of the slug in spite of the nearly symmetric axial power distribution. The cladding mid-wall and coolant temperatures take the maximum at the top of the pin. Temperature of the fuel slug surface over the entire irradiation life is much lower than the fuel-clad eutectic reaction temperature. The fission gas release of the driver fuel pin at the End Of Life(EOL) is predicted to be 68.61% and plenum pressure is too low to cause cladding yielding. The probability that the fuel pin would fail is estimated to be much less than that allowed in the design criteria. The maximum radial deformation of the fuel pin is 1.928%, satisfying the preliminary design criterion (3%) for fuel pin deformation. Therefore the conceptual design parameters of the driver fuel pin for the KALIMER breakeven core are expected to satisfy the preliminary criteria on temperature, fluence limit, deformation limit etc.

Temperature escalation in PWR fuel rod simulator bundles due to the zircaloy/steam reaction: Post test investigations of bundle test ESBU-2A

International Nuclear Information System (INIS)

Hagen, S.; Kapulla, H.; Malauschek, H.; Wallenfels, K.P.; Buescher, B.

1986-11-01

This KfK report describes the post test investigation of bundle experiment ESBU-2a. ESBU-2a was the second of two bundle tests on the temperature escalation of zircaloy clad fuel rods. The investigation of the temperature escalation is part of the program of out-of-pile experiments performed within the frame work of the PNS-Severe Fuel Damage program. The bundle was composed of a 3x3 fuel rod array of our fuel rod simulators (central tungsten heater, UO 2 -ring pellet and zircaloy cladding). The length was 0.4 meter. The bundle was heated to a maximum temperature of 2175 0 C. Molten cladding which dissolved part of the UO 2 pellets and slumped away from the already oxidized cladding formed a lump in the lower part of the bundle. After the test the bundle was embedded in epoxy and sectioned with a diamand saw, in the region of the refrozen melt. The cross sections were investigated by metallographic examination. The refrozen (U,Zr,O) melt consists variously of three phases with increasing oxygen content (metallic α-Zry, metallic (U,Zr) alloy and a (U,Zr)O 2 mixed oxide), two phases (α-Zry, (U,Zr)O 2 mixed oxide), or one phase ((U,Zr)O 2 mixed oxide). The cross sections show the increasing oxidation of the cladding with increasing elevation (temperature). A strong azimuthal dependency of the oxidation is found. In regions where the initial oxidized cladding is contacted by the melt one can recognize the interaction between the metallic melt and ZrO 2 of the cladding. Oxygen is taken away from the ZrO 2 . If the melt is in direct contact with steam a relatively well defined oxide layer is formed. (orig.) [de

Alternatives for water basin spent fuel storage using pin storage

International Nuclear Information System (INIS)

Viebrock, J.M.; Carlson, R.W.

1979-09-01

The densest tolerable form for storing spent nuclear fuel is storage of only the fuel rods. This eliminates the space between the fuel rods and frees the hardware to be treated as non-fuel waste. The storage density can be as much as 1.07 MTU/ft 2 when racks are used that just satisfy the criticality and thermal limitations. One of the major advantages of pin storage is that it is compatible with existing racks; however, this reduces the storage density to 0.69 MTU/ft 2 . Even this is a substantial increase over the 0.39 MTU/ft 2 that is achievable with current high capacity stainless steel racks which have been selected as the bases for comparison. Disassembly requires extensive operation on the fuel assembly to remove the upper end fitting and to extract the fuel rods from the assembly skeleton. These operations will be performed with the aid of an elevator to raise the assembly where each fuel rod is grappled. Lowering the elevator will free the fuel rod for transfer to the storage canister. A storage savings of $1510 per MTU can be realized if the pin storage concept is incorporated at a new away-from-reactor facility. The storage cost ranges from $3340 to $7820 per MTU of fuel stored with the lower cost applying to storage at an existing away-from-reactor storage facility and the higher cost applying to at-reactor storage

Results of transient overpower events on breached and unbreached fuel pins

International Nuclear Information System (INIS)

Strain, R.V.; Tsai, H.C.; Neimark, L.A.; Aratani, K.

1986-04-01

The objective of the extended overpower tests on intact pins was to determine the pin cladding breaching thresholds vis-a-vis the Plant Protection System (PPS) trip settings, typically at ∼10 to 15% overpower. These tests emphasize slow operational-type transients in light of earlier work which suggested that irradiated mixed-oxide fuel pins may be particularly vulnerable in the slow ramp-rate regime. An overview of the extended overpower test series was previously reported. More recent results on two of the tests in this series are included in this paper. These two tests, designated TOPI-1A and TOPI-1B, were each conducted on a 19-pin assembly with various pin design, operation and burnup variables. The overpower ramp rates for the TOPI-1A and -1B tests were 0.1%/s and 10%/s, respectively

Physics evaluation for testino. of RAPS and TAPS fuel pins in CIRUS pressurised water loop

International Nuclear Information System (INIS)

John, Benjamin; Paul, O.P.K.

1976-01-01

Relevant calculations carried out to assess the reactivity effect, heat generation and other parameters for testing of RAPS and TAPS fuel pins in the Cirus pressurised water loop are summarised. The Cirus neutron flux level being low, in order to simulate the RAPS design heat rating of ∫ Kdtheta = 40 w/cm, the required plutonium enrichment in mixed plutonium uranium oxide fuel pin was worked out. The results showed that a PuO 2 enrichment of 1.5 wt percent would be necessary to meet the above requirement. The analysis for the TAPS pin indicated that the desired heat flux of 115w/cm 2 cannot be obtained in the Cirus loop with either a 7 pin cluster geometry, or with a single pin with the enrichment level as used in TAPS pin. Lattice code DUMLAC and the core simulation code AECLHEX were used for these studies. (author)

Report of the collaboration project for research and development of sphere-pac fuel among JNC-PSI-NRG (1). Planning, fuel design, pin fabrication

International Nuclear Information System (INIS)

Morihira, Masayuki; Ozawa, Takayuki; Tomita, Yutaka; Suzuki, Masahiro; Kihara, Yoshiyuki; Shigetome, Yoshiaki; Kohno, Shusaku

2004-07-01

The collaboration project concerning sphere-pac fuel among JNC, Swiss PSI (Paul Scherrer Institut) and Dutch NRG (Nuclear Research and Consultancy Group) is in progress. Final target of the project is comparative irradiation tests of sphere-pac fuel in the HFR (High Flux Reactor) in Petten in the Netherlands with pellet type fuel and vipack fuel. Total 16 fuel segments (8 pins) of these three types of fuel are planned to be irradiated. Two sphere-pac fuel segments contain 5%Np in addition to 20%Pu-MOX. Other segments contain no Np. The objective of the irradiation tests is to obtain the restructuring data in the early beginning of life for SPF as well as power-to-melt test data for the potential study of SPF. At the same time introduction of modeling technique for irradiation performance analysis, fuel design, fuel fabrication is also important objective for JNC. Fabrication of irradiation test pins was completed till May 2003 in PSI. After transportation of the fuel pins to Petten, two times of irradiation were performed in January to March in 2004 and now post irradiation tests are in progress. Later two irradiations will be done till the autumn in 2004. This report summarized the basic plan, fuel design, and fabrication of irradiation test pins concerning this collaboration project. (author)

Visual observations of a degraded bundle of irradiated fuel: the Phebus FPT1 test

International Nuclear Information System (INIS)

Barrachin, M.; Bottomley, P.D.

1999-01-01

The international Phebus-FP (Fission Product) project is managed by the Institut de Protection et Surete Nucleaire in collaboration with Electricite de France (EDF), the European Commission (EC), the USNRC (USA), COG (Canada), NUPEC and JAERI (Japan), KAERI (South Korea), PSI and HSK (Switzerland). It is designed to measure the source-term and to study the degradation of irradiated UO 2 fuel in conditions typical of a severe loss of coolant accident in a pressurised water reactor (PWR). In the first test (FPT0), performed in December '93, a bundle of 20 fresh fuel rods and a central Ag-In-Cd control rod underwent a short 15-day irradiation to generate fission products before testing in the Phebus reactor in Cadarache. The second test (FPT1) was performed in July '96, in the same conditions and geometry, but using irradiated fuel (-23 GWd/tU). In the FPT1 test, the bundle was heated to an estimated 3000 K over a period of 30 minutes in order to induce a substantial liquefaction of the bundle. After the test, the bundle was embedded in epoxy and cut at different levels to investigate the mechanisms of the core degradation. This paper reports the visual observations of the degraded FPT1 bundle, very preliminary interpretations about the scenario of degradation and a comparison between the behaviour of the fuel in the FPT0 and FPT1 tests. (author)

Fission product release assessment for end fitting failure in Candu reactor loaded with CANFLEX-NU fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Oh, Dirk Joo; Jeong, Chang Joon; Lee, Kang Moon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

Fission product release (FPR) assessment for End Fitting Failure (EFF) in CANDU reactor loaded with CANFLEX-natural uranium (NU) fuel bundles has been performed. The predicted results are compared with those for the reactor loaded with standard 37-element bundles. The total channel I-131 release at the end of transient for EFF accident is calculated to be 380.8 TBq and 602.9 TBq for the CANFLEX bundle and standard bundle channel cases, respectively. They are 4.9% and 7.9% of total inventory, respectively. The lower total releases of the CANFLEX bundle O6 channel are attributed to the lower initial fuel temperatures caused by the lower linear element power of the CANFLEX bundle compared with the standard bundle. 4 refs., 1 fig., 4 tabs. (Author)

Fission product release assessment for end fitting failure in Candu reactor loaded with CANFLEX-NU fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Oh, Dirk Joo; Jeong, Chang Joon; Lee, Kang Moon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-12-31

Fission product release (FPR) assessment for End Fitting Failure (EFF) in CANDU reactor loaded with CANFLEX-natural uranium (NU) fuel bundles has been performed. The predicted results are compared with those for the reactor loaded with standard 37-element bundles. The total channel I-131 release at the end of transient for EFF accident is calculated to be 380.8 TBq and 602.9 TBq for the CANFLEX bundle and standard bundle channel cases, respectively. They are 4.9% and 7.9% of total inventory, respectively. The lower total releases of the CANFLEX bundle O6 channel are attributed to the lower initial fuel temperatures caused by the lower linear element power of the CANFLEX bundle compared with the standard bundle. 4 refs., 1 fig., 4 tabs. (Author)

FFTF fuel pin design procedure verification for transient operation

International Nuclear Information System (INIS)

Baars, R.E.

1975-05-01

The FFTF design procedures for evaluating fuel pin transient performance are briefly reviewed, and data where available are compared with design procedure predictions. Specifically, burst conditions derived from Fuel Cladding Transient Tester (FCTT) tests and from ANL loss-of-flow tests are compared with burst pressures computed using the design procedure upon which the cladding integrity limit was based. Failure times are predicted using the design procedure for evaluation of rapid reactivity insertion accidents, for five unterminated TREAT experiments in which well characterized fuel failures were deliberately incurred. (U.S.)

Irradiation of a 19 pin subassembly with mixed carbide fuel in KNK II

Science.gov (United States)

Geithoff, D.; Mühling, G.; Richter, K.

1992-06-01

The presentation deals with the fabrication, irradiation and nondestructive postirradiation examinations of LMR fuel pins with mixed (U, Pu)-carbide fuels. The mixed carbide fuel was fabricated by the European Institute of Transuranium Elements using various fabrication procedures. Fuel composition varied therefore in a wide range of tolerances with respect to oxygen and phase content and microstructure. The 19 carbide pins were irradiated in the fast neutron flux of the KNK II reactor to a burn-up of about 7 at% without any failure in the centre of a KNK "carrier element" at a maximum linear rating of 800 W/cm. After dismantling in the Hot Cells of KfK nondestructive examinations were carried out comprising dimensional controls, radiography, γ-scanning and eddy-current testing. The results indicate differences in fuel behaviour with respect to composition of the fuel.

In-pile post-DNB behavior of a nine-rod PWR-type fuel bundle

International Nuclear Information System (INIS)

Gunnerson, F.S.; MacDonald, P.E.

1980-01-01

The results of an in-pile power-cooling-mismatch (PCM) test designed to investigate the behavior of a nine-rod, PWR-type fuel bundle under intermittent and sustained periods of high temperature film boiling operation are presented. Primary emphasis is placed on the DNB and post-DNB events including rod-to-rod interactions, return to nucleate boiling (RNB), and fuel rod failure. A comparison of the DNB behavior of the individual bundle rods with single-rod data obtained from previous PCM tests is also made

Diametral strain of fast reactor MOX fuel pins with austenitic stainless steel cladding irradiated to high burnup

Energy Technology Data Exchange (ETDEWEB)

Uwaba, Tomoyuki, E-mail: uwaba.tomoyuki@jaea.go.jp [Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Ibaraki 311-1393 (Japan); Ito, Masahiro; Maeda, Koji [Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Ibaraki 311-1393 (Japan)

2011-09-30

Highlights: > We evaluated diametral strain of fast reactor MOX fuel pins irradiated to 130 GWd/t. > The strain was due to cladding void swelling and irradiation creep. > The irradiation creep was caused by internal gas pressure and PCMI. > The PCMI was associated with pellet swelling by rim structure or by cesium uranate. > The latter effect tended to increase the cumulative damage fraction of the cladding. - Abstract: The C3M irradiation test, which was conducted in the experimental fast reactor, 'Joyo', demonstrated that mixed oxide (MOX) fuel pins with austenitic steel cladding could attain a peak pellet burnup of about 130 GWd/t safely. The test fuel assembly consisted of 61 fuel pins, whose design specifications were similar to those of driver fuel pins of a prototype fast breeder reactor, 'Monju'. The irradiated fuel pins exhibited diametral strain due to cladding void swelling and irradiation creep. The cladding irradiation creep strain were due to the pellet-cladding mechanical interaction (PCMI) as well as the internal gas pressure. From the fuel pin ceramographs and {sup 137}Cs gamma scanning, it was found that the PCMI was associated with the pellet swelling which was enhanced by the rim structure formation or by cesium uranate formation. The PCMI due to cesium uranate, which occurred near the top of the MOX fuel column, significantly affected cladding hoop stress and thermal creep, and the latter effect tended to increase the cumulative damage fraction (CDF) of the cladding though the CDF indicated that the cladding still had some margin to failure due to the creep damage.

Effect of bundle junction face and misalignment on the pressure drops across a randomly loaded and aligned 12 bundles in CANDU fuel channel

Energy Technology Data Exchange (ETDEWEB)

Suk, H. C.; Sim, K. S.; Chang, C. H.; Lee, Y. O. [Korea Atomic Energy Reaearch Institute, Taejon (Korea, Republic of)

1996-06-01

The pressure drop of twelve fuel bundle string in the CANDU-6 fuel channel is equal to the sum of the eleven junction pressure losses, the bundle string entrance and exit pressure losses, the skin friction pressure loss, and other appendage pressure losses, where the junction loss is dependent on the bundle and faces and angular alignments of the junctions. The results of the single junction pressure drop tests in a short rig show that the most probable pressure drop of the eleven junction was analytically equal to the eleven times of average pressure drop of all the possible single junction pressure drops, and also that the largest and smallest junction pressure drops across the eleven junctions probably occurred only with BA and BB type junctions, respectively, where A and B denote the bundle end sides with an end-plates on which a company monogram is stamped and unstamped, respectively. 5 refs., 7 figs., 1 tab. (author).