Structure and impacts of fuel economy standards for passenger cars in China

International Nuclear Information System (INIS)

Wagner, David Vance; An Feng; Wang Cheng

2009-01-01

By the end of 2006, there were about 24 million total passenger cars on the roads in China, nearly three times as many as in 2001. To slow the increase in energy consumption by these cars, China began implementing passenger car fuel economy standards in two phases beginning in 2005. Phase 1 fuel consumption limits resulted in a sales-weighted new passenger car average fuel consumption decrease of about 11%, from just over 9 l/100 km to approximately 8 l/100 km, from 2002 to 2006. However, we project that upon completion of Phase 2 limits in 2009, the average fuel consumption of new passenger cars in China may drop only by an additional 1%, to approximately 7.9 l/100 km. This is due to the fact that a majority of cars sold in 2006 already meets the stricter second phase fuel consumption limits. Simultaneously, other trends in the Chinese vehicle market, including increases in average curb weight and increases in standards-exempt imported vehicles, threaten to offset the efficiency gains achieved from 2002 to 2006. It is clear that additional efforts and policies beyond Phase 2 fuel consumption limits are required to slow and, ultimately, reverse the trend of rapidly rising energy consumption and greenhouse gases from China's transportation sector.

Comments on the Joint Proposed Rulemaking to Establish Light-Duty Vehicle Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards

Energy Technology Data Exchange (ETDEWEB)

Wenzel, Tom [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2009-10-27

Tom Wenzel of Lawrence Berkeley National Laboratory comments on the joint rulemaking to establish greenhouse gas emission and fuel economy standards for light-duty vehicle, specifically on the relationship between vehicle weight and vehicle safety.

49 CFR 537.9 - Determination of fuel economy values and average fuel economy.

Science.gov (United States)

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Determination of fuel economy values and average fuel economy. 537.9 Section 537.9 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AUTOMOTIVE FUEL ECONOMY REPORTS § 537.9 Determination of fuel...

Impact of non-petroleum vehicle fuel economy on GHG mitigation potential

International Nuclear Information System (INIS)

Luk, Jason M; Saville, Bradley A; MacLean, Heather L

2016-01-01

The fuel economy of gasoline vehicles will increase to meet 2025 corporate average fuel economy standards (CAFE). However, dedicated compressed natural gas (CNG) and battery electric vehicles (BEV) already exceed future CAFE fuel economy targets because only 15% of non-petroleum energy use is accounted for when determining compliance. This study aims to inform stakeholders about the potential impact of CAFE on life cycle greenhouse gas (GHG) emissions, should non-petroleum fuel vehicles displace increasingly fuel efficient petroleum vehicles. The well-to-wheel GHG emissions of a set of hypothetical model year 2025 light-duty vehicles are estimated. A reference gasoline vehicle is designed to meet the 2025 fuel economy target within CAFE, and is compared to a set of dedicated CNG vehicles and BEVs with different fuel economy ratings, but all vehicles meet or exceed the fuel economy target due to the policy’s dedicated non-petroleum fuel vehicle incentives. Ownership costs and BEV driving ranges are estimated to provide context, as these can influence automaker and consumer decisions. The results show that CNG vehicles that have lower ownership costs than gasoline vehicles and BEVs with long distance driving ranges can exceed the 2025 CAFE fuel economy target. However, this could lead to lower efficiency CNG vehicles and heavier BEVs that have higher well-to-wheel GHG emissions than gasoline vehicles on a per km basis, even if the non-petroleum energy source is less carbon intensive on an energy equivalent basis. These changes could influence the effectiveness of low carbon fuel standards and are not precluded by the light-duty vehicle GHG emissions standards, which regulate tailpipe but not fuel production emissions. (letter)

77 FR 29751 - Agency Information Collection Activity Under OMB Review: Automotive Fuel Economy Reports

Science.gov (United States)

2012-05-18

...-0059] Agency Information Collection Activity Under OMB Review: Automotive Fuel Economy Reports AGENCY... Transportation on whether a manufacturer will comply with an applicable average fuel economy standard for the... R. Katz, Fuel Economy Division, Office of International Policy, Fuel Economy and Consumer Programs...

Clean Cities Strategic Planning White Paper: Light Duty Vehicle Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Saulsbury, Bo [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hopson, Dr Janet L [Univ. of Tennessee, Knoxville, TN (United States); Greene, David [Univ. of Tennessee, Knoxville, TN (United States); Gibson, Robert [Univ. of Tennessee, Knoxville, TN (United States)

2015-04-01

Increasing the energy efficiency of motor vehicles is critical to achieving national energy goals of reduced petroleum dependence, protecting the global climate, and promoting continued economic prosperity. Even with fuel economy and greenhouse gas emissions standards and various economic incentives for clean and efficient vehicles, providing reliable and accurate fuel economy information to the public is important to achieving these goals. This white paper reviews the current status of light-duty vehicle fuel economy in the United States and the role of the Department of Energy (DOE) Clean Cities Program in disseminating fuel economy information to the public.

Fuel economy of hybrid fuel-cell vehicles

Science.gov (United States)

Ahluwalia, Rajesh K.; Wang, X.; Rousseau, A.

The potential improvement in fuel economy of a mid-size fuel-cell vehicle by combining it with an energy storage system has been assessed. An energy management strategy is developed and used to operate the direct hydrogen, pressurized fuel-cell system in a load-following mode and the energy storage system in a charge-sustaining mode. The strategy places highest priority on maintaining the energy storage system in a state where it can supply unanticipated boost power when the fuel-cell system alone cannot meet the power demand. It is found that downsizing a fuel-cell system decreases its efficiency on a drive cycle which is compensated by partial regenerative capture of braking energy. On a highway cycle with limited braking energy the increase in fuel economy with hybridization is small but on the stop-and-go urban cycle the fuel economy can improve by 27%. On the combined highway and urban drive cycles the fuel economy of the fuel-cell vehicle is estimated to increase by up to 15% by hybridizing it with an energy storage system.

Sipping fuel and saving lives: increasing fuel economy withoutsacrificing safety

Energy Technology Data Exchange (ETDEWEB)

Gordon, Deborah; Greene, David L.; Ross, Marc H.; Wenzel, Tom P.

2007-06-11

The public, automakers, and policymakers have long worried about trade-offs between increased fuel economy in motor vehicles and reduced safety. The conclusion of a broad group of experts on safety and fuel economy in the auto sector is that no trade-off is required. There are a wide variety of technologies and approaches available to advance vehicle fuel economy that have no effect on vehicle safety. Conversely, there are many technologies and approaches available to advance vehicle safety that are not detrimental to vehicle fuel economy. Congress is considering new policies to increase the fuel economy of new automobiles in order to reduce oil dependence and reduce greenhouse gas emissions. The findings reported here offer reassurance on an important dimension of that work: It is possible to significantly increase the fuel economy of motor vehicles without compromising their safety. Automobiles on the road today demonstrate that higher fuel economy and greater safety can co-exist. Some of the safest vehicles have higher fuel economy, while some of the least safe vehicles driven today--heavy, large trucks and SUVs--have the lowest fuel economy. At an October 3, 2006 workshop, leading researchers from national laboratories, academia, auto manufacturers, insurance research industry, consumer and environmental groups, material supply industries, and the federal government agreed that vehicles could be designed to simultaneously improve safety and fuel economy. The real question is not whether we can realize this goal, but the best path to get there. The experts' studies reveal important new conclusions about fuel economy and safety, including: (1) Vehicle fuel economy can be increased without affecting safety, and vice versa; (2) Reducing the weight and height of the heaviest SUVs and pickup trucks will simultaneously increase both their fuel economy and overall safety; and (3) Advanced materials can decouple size from mass, creating important new possibilities

Model Year 2017 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2016-11-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

Model Year 2012 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2011-11-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

Model Year 2013 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2012-12-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

Model Year 2011 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2010-11-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

Model Year 2018 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2017-12-07

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

Increasing the Fuel Economy and Safety of New Light-DutyVehicles

Energy Technology Data Exchange (ETDEWEB)

Wenzel, Tom; Ross, Marc

2006-09-18

One impediment to increasing the fuel economy standards forlight-duty vehicles is the long-standing argument that reducing vehiclemass to improve fuel economy will inherently make vehicles less safe.This technical paper summarizes and examines the research that is citedin support of this argument, and presents more recent research thatchallenges it. We conclude that the research claiming that lightervehicles are inherently less safe than heavier vehicles is flawed, andthat other aspects of vehicle design are more important to the on-roadsafety record of vehicles. This paper was prepared for a workshop onexperts in vehicle safety and fuel economy, organized by the William andFlora Hewlett Foundation, to discuss technologies and designs that can betaken to simultaneously improve vehicle safety and fuel economy; theworkshop was held in Washington DC on October 3, 2006.

Fuel Economy Label and CAFE Data

Science.gov (United States)

The Engine and Vehicle Compliance Certification and Fuel Economy Inventory contains measured emissions and fuel economy compliance information for light duty vehicles. Data is collected by EPA to certify compliance with the applicable fuel economy provisions of the Energy Policy and Conservation Act (EPCA) and The Energy Independent Security Act of 2007

Model Year 2015 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2014-12-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

Model Year 2009 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2008-10-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

Model Year 2005 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2004-11-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

Model Year 2016 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2015-11-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

Model Year 2010 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2009-10-14

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

Model Year 2014 Fuel Economy Guide: EPA Fuel Economy Estimates

Energy Technology Data Exchange (ETDEWEB)

None

2013-12-01

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

Gasoline-fueled hybrid vs. conventional vehicle emissions and fuel economy.

Energy Technology Data Exchange (ETDEWEB)

Anderson, J.; Bharathan, D.; He, J.; Plotkin, S.; Santini, D.; Vyas, A.

1999-06-18

This paper addresses the relative fuel economy and emissions behavior, both measured and modeled, of technically comparable, contemporary hybrid and conventional vehicles fueled by gasoline, in terms of different driving cycles. Criteria pollutants (hydrocarbons, carbon monoxide, and nitrogen oxides) are discussed, and the potential emissions benefits of designing hybrids for grid connection are briefly considered. In 1997, Toyota estimated that their grid-independent hybrid vehicle would obtain twice the fuel economy of a comparable conventional vehicle on the Japan 10/15 mode driving cycle. This initial result, as well as the fuel economy level (66 mpg), made its way into the U.S. press. Criteria emissions amounting to one-tenth of Japanese standards were cited, and some have interpreted these results to suggest that the grid-independent hybrid can reduce criteria emissions in the U.S. more sharply than can a conventional gasoline vehicle. This paper shows that the potential of contemporary grid-independent hybrid vehicle technology for reducing emissions and fuel consumption under U.S. driving conditions is less than some have inferred. The importance (and difficulty) of doing test and model assessments with comparable driving cycles, comparable emissions control technology, and comparable performance capabilities is emphasized. Compared with comparable-technology conventional vehicles, grid-independent hybrids appear to have no clear criteria pollutant benefits (or disbenefits). (Such benefits are clearly possible with grid-connectable hybrids operating in zero emissions mode.) However, significant reductions in greenhouse gas emissions (i.e., fuel consumption) are possible with hybrid vehicles when they are used to best advantage.

40 CFR 600.113-78 - Fuel economy calculations.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy calculations. 600.113-78... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.113-78 Fuel economy calculations. The...

40 CFR 600.113-88 - Fuel economy calculations.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy calculations. 600.113-88... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.113-88 Fuel economy calculations. The...

40 CFR 600.113-93 - Fuel economy calculations.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy calculations. 600.113-93... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.113-93 Fuel economy calculations. The...

Feebates, rebates and gas-guzzler taxes: a study of incentives for increased fuel economy

International Nuclear Information System (INIS)

Greene, D.L.; Patterson, P.D.; Singh, Margaret; Li Jia

2005-01-01

US fuel economy standards have not been changed significantly in 20 years. Feebates are a market-based alternative in which vehicles with fuel consumption rates above a 'pivot point' are charged fees while vehicles below receive rebates. By choice of pivot points, feebate systems can be made revenue neutral. Feebates have been analyzed before. This study re-examines feebates using recent data, assesses how the undervaluing of fuel economy by consumers might affect their efficacy, tests sensitivity to the cost of fuel economy technology and price elasticities of vehicle demand, and adds assessments of gas-guzzler taxes or rebates alone. A feebate rate of $500 per 0.01 gallon per mile (GPM) produces a 16 percent increase in fuel economy, while a $1000 per 0.01 GPM results in a 29 percent increase, even if consumers count only the first 3 years of fuel savings. Unit sales decline by about 0.5 percent but sales revenues increase because the added value of fuel economy technologies outweighs the decrease in sales. In all cases, the vast majority of fuel economy increase is due to adoption of fuel economy technologies rather than shifts in sales

Fuel Economy Label and CAFE Data

Data.gov (United States)

U.S. Environmental Protection Agency — The Engine and Vehicle Compliance Certification and Fuel Economy Inventory contains measured emissions and fuel economy compliance information for light duty...

Study of emissions and fuel economy for parallel hybrid versus conventional vehicles on real world and standard driving cycles

Directory of Open Access Journals (Sweden)

Ahmed Al-Samari

2017-12-01

Full Text Available Parallel hybrid electric vehicles (PHEVs increasing rapidly in the automobile markets. However, the benefits out of using this kind of vehicles are still concerned a lot of costumers. This work investigated the expected benefits (such as decreasing emissions and increasing fuel economy from using the parallel HEV in comparison to the conventional vehicle model of the real-world and standard driving cycles. The software Autonomie used in this study to simulate the parallel HEV and conventional models on these driving cycles.The results show that the fuel economy (FE can be improved significantly up to 68% on real-world driving cycle, which is represented mostly city activities. However, the FE improvement was limited (10% on the highway driving cycle, and this is expected since the using of brake system was infrequent. Moreover, the emissions from parallel HEV decreased about 40% on the real-world driving cycle, and decreased 11% on the highway driving cycle. Finally, the engine efficiency, improved about 12% on the real-world driving cycle, and about 7% on highway driving cycle. Keywords: Emissions, Hybrid electric vehicles, Fuel economy, Real-world driving cycle

40 CFR 610.42 - Fuel economy measurement.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy measurement. 610.42... ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria General Vehicle Test Procedures § 610.42 Fuel economy measurement. (a) Fuel consumption will be measured by: (1) The carbon balance method, or...

Multi-objective regulations on transportation fuels: Comparing renewable fuel mandates and emission standards

International Nuclear Information System (INIS)

Rajagopal, D.; Plevin, R.; Hochman, G.; Zilberman, D.

2015-01-01

We compare two types of fuel market regulations — a renewable fuel mandate and a fuel emission standard — that could be employed to simultaneously achieve multiple outcomes such as reduction in fuel prices, fuel imports and greenhouse gas (GHG) emissions. We compare these two types of regulations in a global context taking into account heterogeneity in carbon content of both fossil fuels and renewable fuels. We find that although neither the ethanol mandate nor the emission standard is certain to reduce emissions relative to a business-as-usual baseline, at any given level of biofuel consumption in the policy region, a mandate, relative to an emission standard, results in higher GHG emissions, smaller expenditure on fuel imports, lower price of ethanol-blended gasoline and higher domestic fuel market surplus. This result holds over a wide range of values of model parameters. We also discuss the implications of this result to a regulation such as the US Renewable Fuel Standard given recent developments within the US such as increase in shale and tight oil production and large increase in average vehicle fuel economy of the automotive fleet. - Highlights: • Biofuel mandates and fuel GHG emission standards are analyzed from a multiple criteria perspective • An emission-standard always results in lower global emissions while requiring less biofuel relative to a biofuel mandate • An emission-standard results in higher fuel price in the home region relative to a biofuel mandate • Emission standards lead to more shuffling of both fossil fuels and biofuels between home and abroad • The relative impact of the policies on fuel imports depends on the relative cost-effectiveness of domestic & imported biofuel • Recent developments oil production and fuel economy increase the net benefits of an LCFS approach relative to RFS

Comments on the Joint Proposed Rulemaking to Establish Light-Duty Vehicle Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards

Energy Technology Data Exchange (ETDEWEB)

Wenzel, Thomas P

2009-10-27

I appreciate the opportunity to provide comments on the joint rulemaking to establish greenhouse gas emission and fuel economy standards for light-duty vehicles. My comments are directed at the choice of vehicle footprint as the attribute by which to vary fuel economy and greenhouse gas emission standards, in the interest of protecting vehicle occupants from death or serious injury. I have made several of these points before when commenting on previous NHTSA rulemakings regarding CAFE standards and safety. The comments today are mine alone, and do not necessarily represent the views of the US Department of Energy, Lawrence Berkeley National Laboratory, or the University of California. My comments can be summarized as follows: (1) My updated analysis of casualty risk finds that, after accounting for drivers and crash location, there is a wide range in casualty risk for vehicles with the same weight or footprint. This suggests that reducing vehicle weight or footprint will not necessarily result in increased fatalities or serious injuries. (2) Indeed, the recent safety record of crossover SUVs indicates that weight reduction in this class of vehicles resulted in a reduction in fatality risks. (3) Computer crash simulations can pinpoint the effect of specific design changes on vehicle safety; these analyses are preferable to regression analyses, which rely on historical vehicle designs, and cannot fully isolate the effect of specific design changes, such as weight reduction, on crash outcomes. (4) There is evidence that automakers planned to build more large light trucks in response to the footprint-based light truck CAFE standards. Such an increase in the number of large light trucks on the road may decrease, rather than increase, overall safety.

10 CFR 474.3 - Petroleum-equivalent fuel economy calculation.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Petroleum-equivalent fuel economy calculation. 474.3..., DEVELOPMENT, AND DEMONSTRATION PROGRAM; PETROLEUM-EQUIVALENT FUEL ECONOMY CALCULATION § 474.3 Petroleum-equivalent fuel economy calculation. (a) The petroleum-equivalent fuel economy for an electric vehicle is...

Car buyers and fuel economy?

International Nuclear Information System (INIS)

Turrentine, Thomas S.; Kurani, Kenneth S.

2007-01-01

This research is designed to help researchers and policy makers ground their work in the reality of how US consumers are thinking and behaving with respect to automotive fuel economy. Our data are from semi-structured interviews with 57 households across nine lifestyle 'sectors.' We found no household that analyzed their fuel costs in a systematic way in their automobile or gasoline purchases. Almost none of these households track gasoline costs over time or consider them explicitly in household budgets. These households may know the cost of their last tank of gasoline and the unit price of gasoline on that day, but this accurate information is rapidly forgotten and replaced by typical information. One effect of this lack of knowledge and information is that when consumers buy a vehicle, they do not have the basic building blocks of knowledge assumed by the model of economically rational decision-making, and they make large errors estimating gasoline costs and savings over time. Moreover, we find that consumer value for fuel economy is not only about private cost savings. Fuel economy can be a symbolic value as well, for example among drivers who view resource conservation or thrift as important values to communicate. Consumers also assign non-monetary meaning to fuel prices, for example seeing rising prices as evidence of conspiracy. This research suggests that consumer responses to fuel economy technology and changes in fuel prices are more complex than economic assumptions suggest. The US Department of Energy and the Energy Foundation supported this research. The authors are solely responsible for the content and conclusions presented

76 FR 39477 - Revisions and Additions to Motor Vehicle Fuel Economy Label

Science.gov (United States)

2011-07-06

...The Environmental Protection Agency (EPA) and the National Highway Traffic Safety Administration (NHTSA) are issuing a joint final rule establishing new requirements for the fuel economy and environment label that will be posted on the window sticker of all new automobiles sold in the U.S. The labeling requirements apply for model year 2013 and later vehicles with a voluntary manufacturer option for model year 2012. The labeling requirements apply to passenger cars, light-duty trucks, and medium duty passenger vehicles such as larger sport-utility vehicles and vans. The redesigned label provides expanded information to American consumers about new vehicle fuel economy and fuel consumption, greenhouse gas and smog-forming emissions, and projected fuel costs and savings, and also includes a smartphone interactive code that permits direct access to additional Web resources. Specific label designs are provided for gasoline, diesel, ethanol flexible fuel, compressed natural gas, electric, plug-in hybrid electric, and hydrogen fuel cell vehicles. This rulemaking is in response to provisions in the Energy Independence and Security Act of 2007 that imposed several new labeling requirements and new advanced-technology vehicles entering the market. NHTSA and EPA believe that these changes will help consumers to make more informed vehicle purchase decisions, particularly as the future automotive marketplace provides more diverse vehicle technologies from which consumers may choose. These new label requirements do not affect the methodologies that EPA uses to generate consumer fuel economy estimates, or the automaker compliance values for NHTSA's corporate average fuel economy and EPA's greenhouse gas emissions standards. This action also finalizes a number of technical corrections to EPA's light-duty greenhouse gas emission standards program.

Fuel economy of new passenger cars in Mexico: Trends from 1988 to 2008 and prospects

International Nuclear Information System (INIS)

Sheinbaum-Pardo, Claudia; Chávez-Baeza, Carlos

2011-01-01

This paper analyzes trends in fuel economy (kilometers per liter) of new passenger vehicles in Mexico over a period of 20 years from 1988 to 2008. Results show that in this period, fuel economy of the new passenger vehicle fleet, including multipurpose vehicles (a category similar to sport utility vehicles, SUVs), increased by only 6.3%. A simple Laspeyres index analysis was developed to evaluate both the impact of changes in vehicle sales structure by category and the changes in fuel economy. Results show that increased sales of heavier, multipurpose vehicles in place of subcompact and compact vehicles, impacted negatively on the fleet average fuel economy. If the structure of sales had continued in the same proportions across all categories as in 1988, fuel economy would have increased by 11.0%, instead of the actual 6.3%. This result coincides with trends in other countries. The paper also presents different scenarios of passenger car fuel economy for the year 2020, and its implications for gasoline consumption and CO 2 emissions. The results may influence the new passenger vehicle fuel economy standard that is currently under discussion in Mexico.

Technology Roadmap: Fuel Economy of Road Vehicles

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

This roadmap explores the potential improvement of existing technologies to enhance the average fuel economy of motorised vehicles; the roadmap’s vision is to achieve a 30% to 50% reduction in fuel use per kilometre from new road vehicles including 2-wheelers, LDV s and HDV s) around the world in 2030, and from the stock of all vehicles on the road by 2050. This achievement would contribute to significant reductions in GHG emissions and oil use, compared to a baseline projection. Different motorised modes are treated separately, with a focus on LDV s, HDV s and powered two-wheelers. A section on in-use fuel economy also addresses technical and nontechnical parameters that could allow fuel economy to drastically improve over the next decades. Technology cost analysis and payback time show that significant progress can be made with low or negative cost for fuel-efficient vehicles over their lifetime use. Even though the latest data analysed by the IEA for fuel economy between 2005 and 2008 showed that a gap exists in achieving the roadmap’s vision, cutting the average fuel economy of road motorised vehicles by 30% to 50% by 2030 is achievable, and the policies and technologies that could help meet this challenge are already deployed in many places around the world.

76 FR 31467 - Guide Concerning Fuel Economy Advertising for New Automobiles

Science.gov (United States)

2011-06-01

... the Fuel Economy Guide \\1\\ in 1975 to prevent deceptive fuel economy advertising for new automobiles... Economy Guide. That rulemaking will increase the coverage of EPA's new fuel economy labels to include... issue to new vehicle advertisers in the FTC's Fuel Economy Guide. Therefore, the Commission has...

40 CFR 600.307-08 - Fuel economy label format requirements.

Science.gov (United States)

2010-07-01

... to battery electric vehicles, fuel cell vehicles, plug-in hybrid electric vehicles and vehicles... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy label format requirements...) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy...

Haptic seat for fuel economy feedback

Energy Technology Data Exchange (ETDEWEB)

Bobbitt, III, John Thomas

2016-08-30

A process of providing driver fuel economy feedback is disclosed in which vehicle sensors provide for haptic feedback on fuel usage. Such sensors may include one or more of a speed sensors, global position satellite units, vehicle pitch/roll angle sensors, suspension displacement sensors, longitudinal accelerometer sensors, throttle position in sensors, steering angle sensors, break pressure sensors, and lateral accelerometer sensors. Sensors used singlely or collectively can provide enhanced feedback as to various environmental conditions and operating conditions such that a more accurate assessment of fuel economy information can be provided to the driver.

40 CFR 600.114-08 - Vehicle-specific 5-cycle fuel economy calculations.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Vehicle-specific 5-cycle fuel economy... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy... fuel economy calculations. This section applies to data used for fuel economy labeling under Subpart D...

Predicting Light-Duty Vehicle Fuel Economy as a Function of Highway Speed

Energy Technology Data Exchange (ETDEWEB)

Thomas, John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hwang, Ho-Ling [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); West, Brian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Huff, Shean [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2013-04-08

The www.fueleconomy.gov website offers information such as window label fuel economy for city, highway, and combined driving for all U.S.-legal light-duty vehicles from 1984 to the present. The site is jointly maintained by the U.S. Department of Energy and the U.S. Environmental Protection Agency (EPA), and also offers a considerable amount of consumer information and advice pertaining to vehicle fuel economy and energy related issues. Included with advice pertaining to driving styles and habits is information concerning the trend that as highway cruising speed is increased, fuel economy will degrade. An effort was undertaken to quantify this conventional wisdom through analysis of dynamometer testing results for 74 vehicles at steady state speeds from 50 to 80 mph. Using this experimental data, several simple models were developed to predict individual vehicle fuel economy and its rate of change over the 50-80 mph speed range interval. The models presented require a minimal number of vehicle attributes. The simplest model requires only the EPA window label highway mpg value (based on the EPA specified estimation method for 2008 and beyond). The most complex of these simple model uses vehicle coast-down test coefficients (from testing prescribed by SAE Standard J2263) known as the vehicle Target Coefficients, and the raw fuel economy result from the federal highway test. Statistical comparisons of these models and discussions of their expected usefulness and limitations are offered.

40 CFR Appendix II to Part 600 - Sample Fuel Economy Calculations

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample Fuel Economy Calculations II... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. II Appendix II to Part 600—Sample Fuel Economy Calculations (a) This sample fuel economy calculation is applicable to...

Instrumentation of cars for fuel economy. Final report

Energy Technology Data Exchange (ETDEWEB)

Morris, J E

1982-04-01

The development of an electronic system to control the air-fuel ratio (A/F) and ignition timing of an internal combustion engine to optimize fuel economy is described. Dynamometer and drive cycle testing of the system was performed. The results showed that a significant improvement in fuel economy can be achieved by a control system of the type developed. It is clear, however, that considerably more work needs to be done. One area mentioned is the need for more systematic fuel economy testing against speed and load as control parameters are varied for optimization, and a more economic air bypass system must be developed. (LCL)

40 CFR 600.206-93 - Calculation and use of fuel economy values for gasoline-fueled, diesel-fueled, electric, alcohol...

Science.gov (United States)

2010-07-01

... EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures... equivalent petroleum-based fuel economy value exists for an electric vehicle configuration, all values for... values for gasoline-fueled, diesel-fueled, electric, alcohol-fueled, natural gas-fueled, alcohol dual...

40 CFR 600.510-08 - Calculation of average fuel economy.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy. 600.510-08 Section 600.510-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles...

40 CFR 600.510-93 - Calculation of average fuel economy.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy. 600.510-93 Section 600.510-93 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles...

40 CFR 600.510-86 - Calculation of average fuel economy.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy. 600.510-86 Section 600.510-86 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles...

Effect of Intake Air Filter Condition on Vehicle Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Norman, Kevin M [ORNL; Huff, Shean P [ORNL; West, Brian H [ORNL

2009-02-01

The U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy and the U.S. Environmental Protection Agency (EPA) jointly maintain a fuel economy website (www.fueleconomy.gov), which helps fulfill their responsibility under the Energy Policy Act of 1992 to provide accurate fuel economy information [in miles per gallon (mpg)] to consumers. The site provides information on EPA fuel economy ratings for passenger cars and light trucks from 1985 to the present and other relevant information related to energy use such as alternative fuels and driving and vehicle maintenance tips. In recent years, fluctuations in the price of crude oil and corresponding fluctuations in the price of gasoline and diesel fuels have renewed interest in vehicle fuel economy in the United States. (User sessions on the fuel economy website exceeded 20 million in 2008 compared to less than 5 million in 2004 and less than 1 million in 2001.) As a result of this renewed interest and the age of some of the references cited in the tips section of the website, DOE authorized the Oak Ridge National Laboratory (ORNL) Fuels, Engines, and Emissions Research Center (FEERC) to initiate studies to validate and improve these tips. This report documents a study aimed specifically at the effect of engine air filter condition on fuel economy. The goal of this study was to explore the effects of a clogged air filter on the fuel economy of vehicles operating over prescribed test cycles. Three newer vehicles (a 2007 Buick Lucerne, a 2006 Dodge Charger, and a 2003 Toyota Camry) and an older carbureted vehicle were tested. Results show that clogging the air filter has no significant effect on the fuel economy of the newer vehicles (all fuel injected with closed-loop control and one equipped with MDS). The engine control systems were able to maintain the desired AFR regardless of intake restrictions, and therefore fuel consumption was not increased. The carbureted engine did show a decrease in

Fuel economy and traffic fatalities: multivariate analysis of international data

International Nuclear Information System (INIS)

Noland, Robert B.

2005-01-01

In the US motor vehicle fuel economy standards were imposed in the late 1970s, in response to the oil crises of that decade. Since then, efforts to increase the standards have not occurred, one reason being the argument that smaller vehicles (which are generally more efficient) are considered less safe. Recent analyses (Energy J.( 2004)) suggests that variance in vehicle weights may be more important than the absolute weights of vehicles in making the highway network less safe. In Europe and other countries, which generally have smaller more efficient vehicle fleets, due to relatively high gasoline taxes, this debate has not occurred. In particular, countries such as Great Britain and Sweden have far safer road transport systems than the US but also have much more efficient vehicle fleets. This suggests that either vehicle weight and size are unimportant or if they have an effect it is small compared to other factors. This paper uses international data to build econometric models that examine whether average vehicle fuel economy has any association with road traffic fatalities, while controlling for other factors that are associated with fatalities. The effect on pedestrian fatalities is also analyzed. Cross-sectional time-series data on traffic fatalities from OECD countries is used and negative binomial regression models are developed using panel data to determine whether any associations are present. Results find that changes in vehicle efficiency are not associated with changes in traffic fatalities, suggesting either that size and weight changes over time have not had a strong effect or are not associated with fuel economy improvements

40 CFR 600.209-85 - Calculation of fuel economy values for labeling.

Science.gov (United States)

2010-07-01

... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy Values § 600.209... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of fuel economy values for...

40 CFR 600.209-95 - Calculation of fuel economy values for labeling.

Science.gov (United States)

2010-07-01

... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy Values § 600.209... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of fuel economy values for...

Potential long-term impacts of changes in US vehicle fuel efficiency standards

International Nuclear Information System (INIS)

Bezdek, Roger H.; Wendling, Robert M.

2005-01-01

Changes in corporate average fuel economy (CAFE) standards have not been made due, in part, to concerns over their negative impact on the economy and jobs. This paper simulates the effects of enhanced CAFE standards through 2030 and finds that such changes could increase GDP and create 300,000 jobs distributed widely across states, industries, and occupations. In addition, enhanced CAFE standards could, each year, reduce US oil consumption by 30 billion gallons, save drivers $40 billion, and reduce US greenhouse gas emissions by 100 million tons. However, there is no free lunch. There would be widespread job displacement within many industries, occupations, and states, and increased CAFE standards require that fuel economy be given priority over other vehicle improvements, increase the purchase price of vehicles, require manufacturers to produce vehicles that they otherwise would not, and require consumers to purchase vehicles that would not exist except for CAFE

Automobile Buyer Decisions about Fuel Economy and Fuel Efficiency

OpenAIRE

Kurani, Ken; Turrentine, Thomas

2004-01-01

Much prior research into consumer automotive and fuel purchase behaviors and fuel economy has been shaped by the normative assumptions of economics. Among these assumptions are that consumers should pay attention to costs of fuel and that they are aware of their options to save on fuel over long periods of time, i.e., the life of a vehicle or at least their period of ownership. For example, researchers have analyzed in some depth consumer choices for more fuel economical vehicles in the 1980s...

40 CFR 85.1510 - Maintenance instructions, warranties, emission labeling and fuel economy requirements.

Science.gov (United States)

2010-07-01

..., emission labeling and fuel economy requirements. 85.1510 Section 85.1510 Protection of Environment..., warranties, emission labeling and fuel economy requirements. The provisions of this section are applicable to... for final admission. (d) Fuel economy labeling. (1) The certificate holder shall affix a fuel economy...

40 CFR 600.211-08 - Sample calculation of fuel economy values for labeling.

Science.gov (United States)

2010-07-01

... AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample calculation of fuel economy...

40 CFR 600.210-08 - Calculation of fuel economy values for labeling.

Science.gov (United States)

2010-07-01

... including, but not limited to battery electric vehicles, fuel cell vehicles, plug-in hybrid electric... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of fuel economy values for... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy...

Nuclear fuel burn-up economy

International Nuclear Information System (INIS)

Matausek, M.

1984-01-01

In the period 1981-1985, for the needs of Utility Organization, Beograd, and with the support of the Scientific Council of SR Srbija, work has been performed on the study entitled 'Nuclear Fuel Burn-up Economy'. The forst [phase, completed during the year 1983 comprised: comparative analysis of commercial NPP from the standpoint of nuclear fuel requirements; development of methods for fuel burn-up analysis; specification of elements concerning the nuclear fuel for the tender documentation. The present paper gives the short description of the purpose, content and results achieved in the up-to-now work on the study. (author)

40 CFR Appendix Viii to Part 600 - Fuel Economy Label Formats

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel Economy Label Formats VIII... POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. VIII Appendix VIII to Part 600—Fuel Economy Label Formats EC01MY92.117 EC01MY92.118 EC01MY92.119 EC01MY92.120...

10 CFR Appendix to Part 474 - Sample Petroleum-Equivalent Fuel Economy Calculations

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Sample Petroleum-Equivalent Fuel Economy Calculations..., DEVELOPMENT, AND DEMONSTRATION PROGRAM; PETROLEUM-EQUIVALENT FUEL ECONOMY CALCULATION Pt. 474, App. Appendix to Part 474—Sample Petroleum-Equivalent Fuel Economy Calculations Example 1: An electric vehicle is...

40 CFR 600.006-08 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

... controller, battery configuration, or other components performed within 2,000 miles prior to fuel economy... fuel economy vehicles. 600.006-08 Section 600.006-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel...

40 CFR 600.307-95 - Fuel economy label format requirements.

Science.gov (United States)

2010-07-01

... requirements. (a)(1) Fuel economy labels must be: (i) Rectangular in shape with a minimum height of 4.5 inches... equivalent fuel economy. To convert these values into units of miles per 100 cubic feet of natural gas... per 100 cubic feet of natural gas, multiply by 0.823.” may be replaced by the statement “The fuel...

40 CFR Appendix III to Part 600 - Sample Fuel Economy Label Calculation

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample Fuel Economy Label Calculation...) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. III Appendix III to Part 600—Sample Fuel Economy Label Calculation Suppose that a manufacturer called Mizer...

75 FR 59673 - Public Hearing Locations for the Proposed Fuel Economy Labels

Science.gov (United States)

2010-09-28

...] RIN 2060-AQ09; RIN 2127-AK73 Public Hearing Locations for the Proposed Fuel Economy Labels AGENCY... Vehicle Fuel Economy Label,'' published in the Federal Register on September 23, 2010. The goal of a... testimony or comment on the Agency's proposed revisions and additions to the motor vehicle fuel economy...

Fuel economy handbook

Energy Technology Data Exchange (ETDEWEB)

Short, W [ed.

1979-01-01

An overview of the UK's energy situation from 1950 to 2020 is presented. Problems are discussed and recommendations are made. A strong argument is presented for energy conservation, greater use of nuclear energy, and restrained production of North Sea oil. Specific recommendations are made for financial and operational considerations of (1) new or replacement boiler plants; (2) space heating of factories, offices and similar buildings; and (3) possible use of various fuels including duel-fuel economics and use of wastes. Tariffs and charges are discussed as well as services (e.g. compressed air, cooling water, sources of waste, etc.). Standby considerations (peak load lopping, turbines-engines, parallel or sectioned operation, etc.) and heat distribution (steam, condensate return and uses) are discussed. Throughout, the emphasis is on fuel economy. Savings in process such as recovering waste heat and the storage of heat are considered. For small industrial furnaces, intermittent heating, heat recovery, and the importance of furnace loading are discussed. (MJJ)

Determinants of consumer interest in fuel economy: Lessons for strengthening the conservation argument

International Nuclear Information System (INIS)

Popp, Michael; Vickery, Gina; Dixon, Bruce; Van de Velde, Liesbeth; Van Huylenbroeck, Guido; Verbeke, Wim

2009-01-01

With an outlook for higher global energy prices and concomitant increase of agricultural resources for the pursuit of fuel, consumers are expected to seek more fuel-economic transportation alternatives. This paper examines factors that influence the importance consumers place on fuel economy, with attention given to differences between American and European consumers. In a survey conducted simultaneously in the United States (U.S.) and Belgium in the fall of 2006, respondents in both countries ranked fuel economy high among characteristics considered when purchasing a new vehicle. Overall, respondents in the U.S. placed greater emphasis on fuel economy as a new-vehicle characteristic. Respondents' budgetary concerns carried a large weight when purchasing a new vehicle as reflected in their consideration of a fuel's relative price (e.g. gasoline vs. diesel vs. biofuel) and associated car repair and maintenance costs. On the other hand, high-income Americans displayed a lack of concern over fuel economy. Concern over the environment also played a role since consumers who felt empowered to affect the environment with their purchasing decisions (buying low and clean emission technology and fuels) placed greater importance on fuel economy. No statistically significant effects on fuel economy rankings were found related to vehicle performance, socio-demographic parameters of age, gender or education. Importantly, the tradeoff between using agricultural inputs for energy rather than for food, feed and fiber had no impact on concerns over fuel economy. Finally, contrary to expectations, U.S. respondents who valued domestically produced renewable fuels did not tend to value fuel economy. (author)

75 FR 58077 - Revisions and Additions to Motor Vehicle Fuel Economy Label

Science.gov (United States)

2010-09-23

...The Environmental Protection Agency (EPA) and the National Highway Traffic Safety Administration (NHTSA) are conducting a joint rulemaking to redesign and add information to the current fuel economy label that is posted on the window sticker of all new cars and light- duty trucks sold in the U.S. The redesigned label will provide new information to American consumers about the fuel economy and consumption, fuel costs, and environmental impacts associated with purchasing new vehicles beginning with model year 2012 cars and trucks. This action will also develop new labels for certain advanced technology vehicles, which are poised to enter the U.S. market, in particular plug-in hybrid electric vehicles and electric vehicles. NHTSA and EPA are proposing these changes because the Energy Independence and Security Act (EISA) of 2007 imposes several new labeling requirements, because the agencies believe that the current labels can be improved to help consumers make more informed vehicle purchase decisions, and because the time is right to develop new labels for advanced technology vehicles that are being commercialized. This proposal is also consistent with the recent joint rulemaking by EPA and NHTSA that established harmonized federal greenhouse gas (GHG) emissions and corporate average fuel economy (CAFE) standards for new cars, sport utility vehicles, minivans, and pickup trucks for model years 2012-2016.

Consumer Views: Importance of Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Singer, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-04-11

This presentation includes data captured by the National Renewable Energy Laboratory (NREL) to support the U.S. Department of Energy's Vehicle Technologies Office (VTO) research efforts. The data capture consumer views on the importance of fuel economy amongst other vehicle attributes and views on which alternative fuel types would be the best and worst replacements for gasoline.

Determining Off-Cycle Fuel Economy Benefits of 2-Layer HVAC Technology

Energy Technology Data Exchange (ETDEWEB)

Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Moniot, Matthew [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jehlik, Forrest [Argonne National Laboratory; Chevers, Netsanet [Toyota Motor North America R& D; Hirabayshi, Hidekazu [Toyota Motor North America R& D; Song, Yuanpei [DENSO International America Inc.

2018-04-03

This work presents a methodology to determine the off-cycle fuel economy benefit of a 2-Layer HVAC system which reduces ventilation and heat rejection losses of the heater core versus a vehicle using a standard system. Experimental dynamometer tests using EPA drive cycles over a broad range of ambient temperatures were conducted on a highly instrumented 2016 Lexus RX350 (3.5L, 8 speed automatic). These tests were conducted to measure differences in engine efficiency caused by changes in engine warmup due to the 2-Layer HVAC technology in use versus the technology being disabled (disabled equals fresh air-considered as the standard technology baseline). These experimental datasets were used to develop simplified response surface and lumped capacitance vehicle thermal models predictive of vehicle efficiency as a function of thermal state. These vehicle models were integrated into a database of measured on road testing and coupled with U.S. typical meteorological data to simulate vehicle efficiency across seasonal thermal and operational conditions for hundreds of thousands of drive cycles. Fuel economy benefits utilizing the 2-Layer HVAC technology are presented in addition to goodness of fit statistics of the modeling approach relative to the experimental test data.

The cost of fuel economy in the Indian passenger vehicle market

International Nuclear Information System (INIS)

Chugh, Randy; Cropper, Maureen; Narain, Urvashi

2011-01-01

To investigate how fuel economy is valued in the Indian car market, we compute the cost to Indian consumers of purchasing a more fuel-efficient vehicle and compare it to the benefit of lower fuel costs over the life of the vehicle. We estimate hedonic price functions for four market segments (petrol hatchbacks, diesel hatchbacks, petrol sedans, and diesel sedans) to compute 95% confidence intervals for the marginal cost to the consumer for an increase in fuel economy. We find that the associated present value of fuel savings falls within the 95% confidence interval for most specifications, in all market segments, for the years 2002 through 2006. Thus, we fail to consistently reject the hypothesis that consumers appropriately value fuel economy. - Highlights: → We examine the tradeoffs faced by new vehicle consumers in India. → We use hedonic price functions and instrumental variables. → We find no support for the hypothesis that consumers undervalue fuel economy. → Some consumers are willing to forgo substantial potential savings to own their preferred vehicle.

40 CFR 600.006-86 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

... fuel economy vehicles. 600.006-86 Section 600.006-86 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-General Provisions § 600.006-86 Data and...

40 CFR 600.006-89 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

... fuel economy vehicles. 600.006-89 Section 600.006-89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-General Provisions § 600.006-89 Data and...

Automotive Stirling engine development program. [fuel economy assessment

Science.gov (United States)

Kitzner, E. W.

1978-01-01

The Ford/DOE automotive Stirling engine development program is directed towards establishing the technological and developmental base that would enable a decision on whether an engineering program should be directed at Stirling engine production. The fuel economy assessment aims to achieve, with a high degree of confidence, the ERDA proposal estimate of 20.6 MPG (gasoline) for a 4500 lb 1WC Stirling engine passenger car. The current M-H fuel economy projection for the 170 HP Stirling engine is 15.7 MPG. The confidence level for this projection is 32%. A confidence level of 29% is projected for a 22.1 MPG estimate. If all of the planned analyses and test work is accomplished at the end of the one year effort, and the projected improvements are substantiated, the confidence levels would rise to 59% for the 20.6 MPG projection and 54% for the 22.1 MPG projection. Progress achieved thus far during the fuel economy assessment is discussed.

In-use fuel economy of hybrid-electric school buses in Iowa.

Science.gov (United States)

Hallmark, Shauna; Sperry, Bob; Mudgal, Abhisek

2011-05-01

Although it is much safer and more fuel-efficient to transport children to school in buses than in private vehicles, school buses in the United States still consume 822 million gal of diesel fuel annually, and school transportation costs can account for a significant portion of resource-constrained school district budgets. Additionally, children in diesel-powered school buses may be exposed to higher levels of particulates and other pollutants than children in cars. One solution to emission and fuel concerns is use of hybrid-electric school buses, which have the potential to reduce emissions and overall lifecycle costs compared with conventional diesel buses. Hybrid-electric technologies are available in the passenger vehicle market as well as the transit bus market and have a track record indicating fuel economy and emissions benefits. This paper summarizes the results of an in-use fuel economy evaluation for two plug-in hybrid school buses deployed in two different school districts in Iowa. Each school district selected a control bus with a route similar to that of the hybrid bus. Odometer readings, fuel consumption, and maintenance needs were recorded for each bus. The buses were deployed in 2008 and data were collected through May 2010. Fuel consumption was calculated for each school district. In Nevada, IA, the overall average fuel economy was 8.23 mpg for the hybrid and 6.35 mpg for the control bus. In Sigourney, IA, the overall average fuel economy was 8.94 mpg for the hybrid and 6.42 mpg for the control bus. The fuel consumption data were compared for the hybrid and control buses using a Wilcoxon signed rank test. Results indicate that fuel economy for the Nevada hybrid bus was 29.6% better than for the Nevada control bus, and fuel economy for the Sigourney hybrid bus was 39.2% higher than for the Sigourney control bus. Both differences were statistically significant.

Reforming fossil fuel prices in India: Dilemma of a developing economy

International Nuclear Information System (INIS)

Anand, Mukesh Kumar

2016-01-01

Over the period between 1990–1 and 2012–3, fossil fuel use on farms has risen and its indirect use in farming, particularly for non-energy purposes, is also growing. Consequently, both energy intensity and fossil fuel intensity are rising for Indian agriculture. But, these are declining for the aggregate Indian economy. Thus, revision of fossil fuel prices acquires greater significance for Indian agriculture than for rest of the economy. There are significant differences across crops. The crop-level analysis is supplemented by an alternative approach that utilizes a three-sector input–output (I–O) model for the Indian economy representing farming, fossil fuels, and rest of economy. Fossil fuels sector is assessed to portray, in general, strong forward linkages. The increase in total cost of farming, for a given change in fossil fuel prices, is estimated as a multiple of increase in direct input cost of fossil fuels in farming. From the three-sector aggregated economy this multiple was estimated at 3.99 for 1998–9. But it grew to 6.7 in 2007–8. The findings have stronger ramifications than commonly recognized, for inflation and cost of implementing the policy on food security. - Highlights: •Fossil fuels’ contribution in primary energy supply has risen from 55 to 75 per cent. •Energy intensity halved for aggregate GDP, but doubled for agricultural GDP. •Impact of fossil fuel price increase on farming costs mimics a widening spiral. •Total cost of farming may increase 6.7 times the increase in direct fuel input cost.

40 CFR 600.314-08 - Updating label values, annual fuel cost, Gas Guzzler Tax, and range of fuel economy for...

Science.gov (United States)

2010-07-01

... cost, Gas Guzzler Tax, and range of fuel economy for comparable automobiles. 600.314-08 Section 600.314-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...

Experiment and Simulation of Medium-Duty Tactical Truck for Fuel Economy Improvement

Directory of Open Access Journals (Sweden)

Allen M. Quail

2011-02-01

Full Text Available Fuel economy improvement on medium-duty tactical truck has and continues to be a significant initiative for the U.S. Army. The focus of this study is the investigation of Automated Manual Transmissions (AMT and mild hybridization powertrain that have potential to improve the fuel economy of the 2.5-ton cargo trucks. The current platform uses a seven-speed automatic transmission. This study utilized a combination of on-road experimental vehicle data and analytical vehicle modeling and simulation. This paper presents the results of (1 establishment of a validated, high fidelity baseline analytical vehicle model, (2 modeling and simulation of two AMTs and their control strategy, (3 optimization of transmissions shift schedules, and (4 modeling and simulation of engine idle stop/start and Belt-Integrated-Starter-Generator (B-ISG systems to improve the fuel economy. The fuel economy discrepancy between experimental average and the baseline simulation result was 2.87%. The simulation results indicated a 14.5% and 12.2% fuel economy improvement for the 10-speed and 12-speed AMT respectively. A stop/start system followed by a B-ISG mild hybrid system incorporating regenerative braking was estimated to improve fuel economy 3.39% and 10.2% respectively.

Hydraulic Hybrid and Conventional Parcel Delivery Vehicles' Measured Laboratory Fuel Economy on Targeted Drive Cycles

Energy Technology Data Exchange (ETDEWEB)

Lammert, M. P.; Burton, J.; Sindler, P.; Duran, A.

2014-10-01

This research project compares laboratory-measured fuel economy of a medium-duty diesel powered hydraulic hybrid vehicle drivetrain to both a conventional diesel drivetrain and a conventional gasoline drivetrain in a typical commercial parcel delivery application. Vehicles in this study included a model year 2012 Freightliner P100H hybrid compared to a 2012 conventional gasoline P100 and a 2012 conventional diesel parcel delivery van of similar specifications. Drive cycle analysis of 484 days of hybrid parcel delivery van commercial operation from multiple vehicles was used to select three standard laboratory drive cycles as well as to create a custom representative cycle. These four cycles encompass and bracket the range of real world in-use data observed in Baltimore United Parcel Service operations. The NY Composite cycle, the City Suburban Heavy Vehicle Cycle cycle, and the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) cycle as well as a custom Baltimore parcel delivery cycle were tested at the National Renewable Energy Laboratory's Renewable Fuels and Lubricants Laboratory. Fuel consumption was measured and analyzed for all three vehicles. Vehicle laboratory results are compared on the basis of fuel economy. The hydraulic hybrid parcel delivery van demonstrated 19%-52% better fuel economy than the conventional diesel parcel delivery van and 30%-56% better fuel economy than the conventional gasoline parcel delivery van on cycles other than the highway-oriented HHDDT cycle.

40 CFR 600.206-86 - Calculation and use of fuel economy values for gasoline-fueled, diesel, and electric vehicle...

Science.gov (United States)

2010-07-01

... values for gasoline-fueled, diesel, and electric vehicle configurations. 600.206-86 Section 600.206-86...-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year... values for gasoline-fueled, diesel, and electric vehicle configurations. (a) Fuel economy values...

Policy Pathways: Improving the Fuel Economy of Road Vehicles - A policy package

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

The transportation sector accounts for approximately one-fifth of global final energy consumption and will account for nearly all future growth in oil use, particularly for road vehicles. The right policy mix can allow countries to improve the fuel economy of road vehicles, which in turn can enhance energy security and reduce CO2 emissions. Improving the Fuel Economy of Road Vehicles highlights lessons learned and examples of good practices from countries with experience in implementing fuel economy policies for vehicles. The report, part of the IEA’s Policy Pathway series, outlines key steps in planning, implementation, monitoring and evaluation. It complements the IEA Technology Roadmap: Fuel Economy for Road Vehicles, which outlines technical options, potentials, and costs towards improvement in the near, medium and long term.

40 CFR 600.006-87 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

..., motor controller, battery configuration, or other components performed within 2,000 miles prior to fuel... fuel economy vehicles. 600.006-87 Section 600.006-87 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel...

Substantial Improvements of Fuel Economy

DEFF Research Database (Denmark)

Jørgensen, Kaj; Nielsen, Lars H.

1996-01-01

The paper evaluates the scope for improving the energy and environmental impacts of road transport by means of electrical and hybrid propulsion. These technologies promise considerable improvements of the fuel economy compared to equivalent vehicles mas well as beneficial effects for the energy...... and traffic systems. A case study concerning passenger cars is analysed by means of computer simulation....

Motor vehicle fuel economy, the forgotten HC control stragegy?

Energy Technology Data Exchange (ETDEWEB)

Deluchi, M.; Wang, Quanlu; Greene, D.L.

1992-06-01

Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

76 FR 54932 - Revisions and Additions to Motor Vehicle Fuel Economy Label; Correction

Science.gov (United States)

2011-09-06

...-AK73 Revisions and Additions to Motor Vehicle Fuel Economy Label; Correction AGENCY: Environmental... regarding labeling of cars and trucks with fuel economy and environmental information in the Federal...

Automobile fuel; Economy and CO2 emissions in industrialized countries : troubling trends through 2005/6

Science.gov (United States)

2005-01-01

A review of recently available data on both on-road fuel economy and new car test fuel economy : shows that while US on-road fuel economy has been flat for almost 15 years, major European countries and Japan have shown modest improvements in response...

Fuel economy and range estimates for fuel cell powered automobiles

Energy Technology Data Exchange (ETDEWEB)

Steinbugler, M.; Ogden, J. [Princeton Univ., NJ (United States)

1996-12-31

While a number of automotive fuel cell applications have been demonstrated, including a golf cart, buses, and a van, these systems and others that have been proposed have utilized differing configurations ranging from direct hydrogen fuel cell-only power plants to fuel cell/battery hybrids operating on reformed methanol. To date there is no clear consensus on which configuration, from among the possible combinations of fuel cell, peaking device, and fuel type, is the most likely to be successfully commercialized. System simplicity favors direct hydrogen fuel cell vehicles, but infrastructure is lacking. Infrastructure favors a system using a liquid fuel with a fuel processor, but system integration and performance issues remain. A number of studies have analyzed particular configurations on either a system or vehicle scale. The objective of this work is to estimate, within a consistent framework, fuel economies and ranges for a variety of configurations using flexible models with the goal of identifying the most promising configurations and the most important areas for further research and development.

Algal biodiesel economy and competition among bio-fuels.

Science.gov (United States)

Lee, D H

2011-01-01

This investigation examines the possible results of policy support in developed and developing economies for developing algal biodiesel through to 2040. This investigation adopts the Taiwan General Equilibrium Model-Energy for Bio-fuels (TAIGEM-EB) to predict competition among the development of algal biodiesel, bioethanol and conventional crop-based biodiesel. Analytical results show that algal biodiesel will not be the major energy source in 2040 without strong support in developed economies. In contrast, bioethanol enjoys a development advantage relative to both forms of biodiesel. Finally, algal biodiesel will almost completely replace conventional biodiesel. CO(2) reduction benefits the development of the bio-fuels industry. Copyright © 2010 Elsevier Ltd. All rights reserved.

Vehicle technologies, fuel-economy policies, and fuel-consumption rates of Chinese vehicles

International Nuclear Information System (INIS)

Huo Hong; He Kebin; Wang, Michael; Yao Zhiliang

2012-01-01

One of the principal ways to reduce transport-related energy use is to reduce fuel-consumption rates of motor vehicles (usually measured in liters of fuel per 100 km). Since 2004, China has implemented policies to improve vehicle technologies and lower the fuel-consumption rates of individual vehicles. Policy evaluation requires accurate and adequate information on vehicle fuel-consumption rates. However, such information, especially for Chinese vehicles under real-world operating conditions, is rarely available from official sources in China. For each vehicle type we first review the vehicle technologies and fuel-economy policies currently in place in China and their impacts. We then derive real-world (or on-road) fuel-consumption rates on the basis of information collected from various sources. We estimate that the real-world fuel-consumption rates of vehicles in China sold in 2009 are 9 L/100 km for light-duty passenger vehicles, 11.4 L/100 km for light-duty trucks, 22 L/100 km for inter-city transport buses, 40 L/100 km for urban transit buses, and 24.9 L/100 km for heavy-duty trucks. These results aid in understanding the levels of fuel consumption of existing Chinese vehicle fleets and the effectiveness of policies in reducing on-road fuel consumption, which can help in designing and evaluating future vehicle energy-efficiency policies. - Highlights: ► Vehicle fuel-consumption rate (VFCR) data are rarely available in China. ► We review the fuel-economy policies currently in place in China and their impacts. ► We derive real-world VFCRs on the basis of information collected from various sources. ► Results aid in understanding the fuel consumption levels of Chinese vehicle fleets. ► Results help in designing and evaluating future vehicle energy-efficiency policies.

Real-world fuel economy and CO2 emissions of plug-in hybrid electric vehicles

International Nuclear Information System (INIS)

Ploetz, Patrick; Funke, Simon Arpad; Jochem, Patrick

2015-01-01

Plug-in hybrid electric vehicles (PHEV) combine electric propulsion with an internal combustion engine. Their potential to reduce transport related green-house gas emissions highly depends on their actual usage and electricity provision. Various studies underline their environmental and economic advantages, but are based on standardised driving cycles, simulations or small PHEV fleets. Here, we analyse real-world fuel economy of PHEV and the factors influencing it based on about 2,000 actual PHEV that have been observed over more than a year in the U.S. and Germany. We find that real-world fuel economy of PHEV differ widely among users. The main factors explaining this variation are the annual mileage, the regularity of daily driving, and the likelihood of long-distance trips. Current test cycle fuel economy ratings neglect these factors. Despite the broad range of PHEV fuel economies, the test cycle fuel economy ratings can be close to empiric PHEV fleet averages if the average annual mile-age is about 17,000 km. For the largest group of PHEV in our data, the Chevrolet Volt, we find the average fuel economy to be 1.45 litres/100 km at an average electric driving share of 78%. The resulting real-world tank-to-wheel CO 2 emissions of these PHEV are 42 gCO 2 /km and the annual CO 2 savings in the U.S. amount to about 50 Mt. In conclusion, the variance of empirical PHEV fuel economy is considerably higher than of conventional vehicles. This should be taken into account by future test cycles and high electric driving shares should be incentivised.

Quantifying the Effects of Idle-Stop Systems on Fuel Economy in Light-Duty Passenger Vehicles

Energy Technology Data Exchange (ETDEWEB)

Jeff Wishart; Matthew Shirk

2012-12-01

Vehicles equipped with idle-stop (IS) systems are capable of engine shut down when the vehicle is stopped and rapid engine re-start for the vehicle launch. This capability reduces fuel consumption and emissions during periods when the engine is not being utilized to provide propulsion or to power accessories. IS systems are a low-cost and fast-growing technology in the industry-wide pursuit of increased vehicle efficiency, possibly becoming standard features in European vehicles in the near future. In contrast, currently there are only three non-hybrid vehicle models for sale in North America with IS systems and these models are distinctly low-volume models. As part of the United States Department of Energy’s Advanced Vehicle Testing Activity, ECOtality North America has tested the real-world effect of IS systems on fuel consumption in three vehicle models imported from Europe. These vehicles were chosen to represent three types of systems: (1) spark ignition with 12-V belt alternator starter; (2) compression ignition with 12-V belt alternator starter; and (3) direct-injection spark ignition, with 12-V belt alternator starter/combustion restart. The vehicles have undergone both dynamometer and on-road testing; the test results show somewhat conflicting data. The laboratory data and the portion of the on-road data in which driving is conducted on a prescribed route with trained drivers produced significant fuel economy improvement. However, the fleet data do not corroborate improvement, even though the data show significant engine-off time. It is possible that the effects of the varying driving styles and routes in the fleet testing overshadowed the fuel economy improvements. More testing with the same driver over routes that are similar with the IS system-enabled and disabled is recommended. There is anecdotal evidence that current Environmental Protection Agency fuel economy test procedures do not capture the fuel economy gains that IS systems produce in real

1998 Annual Study Report. Standardization of methods for measuring fuel economy of hybrid electric vehicles; 1998 nendo seika hokokusho. Hybrid denki jidosha no nenpi sokutei hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The hybrid electric vehicle (HEV) has been attracting attention as a clean energy vehicle, because it will potentially show higher fuel economy and release smaller quantities of exhaust emissions than the conventional internal combustion engine, and also will be potentially advantageous over the electric vehicle in that it needs no charging infrastructures and less cost. However, there are many types of hybrid vehicle systems, and, for them to be commercialized on a large scale, it is urgently necessary to establish the fuel economy measurement method. The 1998 R and D efforts were directed to analysis of the effects of the hybrid-characteristic factors (SOC of the propulsion battery and regenerative braking) on fuel economy and exhaust emissions. As a result, it is found that changed SOC before and after the tests must be corrected to determine fuel economy and that it is possible. The method for measuring the effects of regenerative braking should be further developed, because the data collected while the vehicle is running on road and on a two-wheel chassis dynamometer are not clearly distinguished from each other. The exhaust emissions are also sensitive to the changed SOC, correction for which, however, is not as easy as that for fuel economy. (NEDO)

Motor vehicle fuel economy, the forgotten HC control stragegy. [Hydrocarbon (HC)

Energy Technology Data Exchange (ETDEWEB)

Deluchi, M.; Wang, Quanlu; Greene, D.L.

1992-06-01

Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

Real-world fuel economy and CO{sub 2} emissions of plug-in hybrid electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Ploetz, Patrick; Funke, Simon Arpad; Jochem, Patrick [Fraunhofer-Institut fuer System- und Innovationsforschung (ISI), Karlsruhe (Germany). Competence Center Energiepolitik und Energiesysteme

2015-07-01

Plug-in hybrid electric vehicles (PHEV) combine electric propulsion with an internal combustion engine. Their potential to reduce transport related green-house gas emissions highly depends on their actual usage and electricity provision. Various studies underline their environmental and economic advantages, but are based on standardised driving cycles, simulations or small PHEV fleets. Here, we analyse real-world fuel economy of PHEV and the factors influencing it based on about 2,000 actual PHEV that have been observed over more than a year in the U.S. and Germany. We find that real-world fuel economy of PHEV differ widely among users. The main factors explaining this variation are the annual mileage, the regularity of daily driving, and the likelihood of long-distance trips. Current test cycle fuel economy ratings neglect these factors. Despite the broad range of PHEV fuel economies, the test cycle fuel economy ratings can be close to empiric PHEV fleet averages if the average annual mile-age is about 17,000 km. For the largest group of PHEV in our data, the Chevrolet Volt, we find the average fuel economy to be 1.45 litres/100 km at an average electric driving share of 78%. The resulting real-world tank-to-wheel CO{sub 2} emissions of these PHEV are 42 gCO{sub 2}/km and the annual CO{sub 2} savings in the U.S. amount to about 50 Mt. In conclusion, the variance of empirical PHEV fuel economy is considerably higher than of conventional vehicles. This should be taken into account by future test cycles and high electric driving shares should be incentivised.

On-Road Validation of a Simplified Model for Estimating Real-World Fuel Economy: Preprint

Energy Technology Data Exchange (ETDEWEB)

Wood, Eric; Gonder, Jeff; Jehlik, Forrest

2017-01-01

On-road fuel economy is known to vary significantly between individual trips in real-world driving conditions. This work introduces a methodology for rapidly simulating a specific vehicle's fuel economy over the wide range of real-world conditions experienced across the country. On-road test data collected using a highly instrumented vehicle is used to refine and validate this modeling approach. Model accuracy relative to on-road data collection is relevant to the estimation of 'off-cycle credits' that compensate for real-world fuel economy benefits that are not observed during certification testing on a chassis dynamometer.

Benefits of recent improvements in vehicle fuel economy.

Science.gov (United States)

2014-10-01

For the past several years, we have calculated (on a monthly basis) the average, sales-weighted fuel economy of all light-duty vehicles (cars, pickup trucks, vans, and SUVs) sold in : the U.S. The results indicate that, from October 2007 to September...

40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy and carbon-related exhaust emission values...

Science.gov (United States)

2010-07-01

...-based fuel economy and carbon-related exhaust emission values for a model type. 600.208-12 Section 600... ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...-based and HFET-based fuel economy and carbon-related exhaust emission values for a model type. (a) Fuel...

Nuclear fuel burn-up economy; Ekonomija izgaranja nuklearnog goriva

Energy Technology Data Exchange (ETDEWEB)

Matausek, M [Institute of nuclear sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

1984-07-01

In the period 1981-1985, for the needs of Utility Organization, Beograd, and with the support of the Scientific Council of SR Srbija, work has been performed on the study entitled 'Nuclear Fuel Burn-up Economy'. The forst [phase, completed during the year 1983 comprised: comparative analysis of commercial NPP from the standpoint of nuclear fuel requirements; development of methods for fuel burn-up analysis; specification of elements concerning the nuclear fuel for the tender documentation. The present paper gives the short description of the purpose, content and results achieved in the up-to-now work on the study. (author)

40 CFR 600.209-08 - Calculation of vehicle-specific 5-cycle fuel economy values for a model type.

Science.gov (United States)

2010-07-01

...-cycle fuel economy values for a model type. 600.209-08 Section 600.209-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for...

Fuel economy and life-cycle cost analysis of a fuel cell hybrid vehicle

Science.gov (United States)

Jeong, Kwi Seong; Oh, Byeong Soo

The most promising vehicle engine that can overcome the problem of present internal combustion is the hydrogen fuel cell. Fuel cells are devices that change chemical energy directly into electrical energy without combustion. Pure fuel cell vehicles and fuel cell hybrid vehicles (i.e. a combination of fuel cell and battery) as energy sources are studied. Considerations of efficiency, fuel economy, and the characteristics of power output in hybridization of fuel cell vehicle are necessary. In the case of Federal Urban Driving Schedule (FUDS) cycle simulation, hybridization is more efficient than a pure fuel cell vehicle. The reason is that it is possible to capture regenerative braking energy and to operate the fuel cell system within a more efficient range by using battery. Life-cycle cost is largely affected by the fuel cell size, fuel cell cost, and hydrogen cost. When the cost of fuel cell is high, hybridization is profitable, but when the cost of fuel cell is less than 400 US$/kW, a pure fuel cell vehicle is more profitable.

Potential Fuel Economy Improvements from the Implementation of cEGR and CDA on an Atkinson Cycle Engine

Science.gov (United States)

Present the implementation of cEGR and CDA on an Atkinson engine and use steady state fuel consumption maps to estimate the technologies’ potential fuel economy improvements over the FTP and Highway tests. In addition to use fuel weighted modes to determine possible fuel economy...

Fuel economy improvement based on a many-gear shifting strategy

Energy Technology Data Exchange (ETDEWEB)

Mashadi, B. [School of Automotive Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Baghaei Lakeh, R. [Department of Mechanical Engineering, Southern Illinois University, Edwardsville (United States)

2012-07-01

Considering the engine operating condition in terms of engine load and engine speed, a fuzzy decision making system has been developed. The objective was to controlling the engine operating point in the engine torque-rpm map, in order to enhance fuel economy. The main idea stems from the approach of tracking the defined target curve in the engine map similar to the CVT control criteria. To provide resemblance between a traditional geared transmission and a CVT, a many-gear transmission concept was introduced. A Fuzzy control was utilized by defining proper membership functions for the inputs and output. The efficient fuel consumption curve in the engine map was taken as the target of controller. The effect of engine output power on fuel consumption has also been taken into consideration. Making use of ADVISOR software, vehicle simulations was performed for the many-gear base case and a very good consistency was found with the CVT case. As a result the fuel consumption was found to become considerably less than existing values. The developed strategy was then applied to other cases including conventional manual and automatic transmissions and improvements in the fuel economy was observed.

Hydrogen Fuel Cell Vehicle Fuel Economy Testing at the U.S. EPA National Vehicle and Fuel Emissions Laboratory (SAE Paper 2004-01-2900)

Science.gov (United States)

The introduction of hydrogen fuel cell vehicles and their new technology has created the need for development of new fuel economy test procedures and safety procedures during testing. The United States Environmental Protection Agency-National Vehicle Fuels and Emissions Laborato...

A study on the effects of the CAFE standard on consumers

International Nuclear Information System (INIS)

Jun, Seung-Pyo; Yoo, Hyoung Sun; Kim, Ji-Hui

2016-01-01

In this paper, we analyzed how the CAFE standard has affected improvements in the fuel economy of vehicles, as examined in other preceding studies, but in addition, we also analyzed how these standards have affected the level of consumer interest in fuel economy. Our goal was to determine what effects the government intervention has had on consumers, and whether such intervention ought to be continued. The results showed that not only has the CAFE standard had a direct and significant impact on improving fuel economy and increasing the market share of fuel-efficient vehicles, it has also boosted the development of technologies for enhancing fuel economy and raised consumer interest in fuel economy, thus indirectly contributing to overcoming market failure. The significance of this study is that we used publically available observed data and analyzed the recent impact of the CAFE standard specifically with a focus on the behavior and strategies exhibited by consumers and automakers. Another significance of this study is that it extends our purview to examine the effects that the CAFE standard has had in other countries (Korea). - Highlights: •CAFE standards have raised consumer interest in fuel economy such as MPG. •CAFE standards had a significant impact on increasing fuel-efficient vehicles •Sales of HEVs are more significantly affected by CAFE standards than by WTI. •CAFE standards had a significant impact on a foreign vehicle market. •Analysis suggests the standards will continue to be necessary for market growth.

Demand for road-fuel in a small developing economy: The case of Sri Lanka

International Nuclear Information System (INIS)

Chandrasiri, Sunil

2006-01-01

This paper estimates the demand for road fuel (petrol and auto-diesel) in the context of a small developing economy-Sri Lanka. The data set covers a period of 39 years from 1964 to 2002 representing both close economy and open economy policy regimes. The estimation procedure is based on seemingly unrelated regression equation (SURE) methodology mainly to capture substitutability of petrol and diesel in road transportation. The effect of auto-fuel prices on vehicle demand is also analyzed as a part of the analysis. In addition to confirming existing evidence on road-fuel demand, the findings reveal some interesting evidence with respect to own-price elasticity, cross-price elasticity, lag effects, income and vehicle mix variables

Several remarks on the fuel cycle economy

International Nuclear Information System (INIS)

Roman Kubin; Rudolf Vespalec

2007-01-01

Present paper deals with some aspects influencing significantly cost of nuclear fuel and possibilities of its usage in optimal fuel cycle technology. Our discussion is focused on the phase of fuel procurement that means financial parts of the contract as well as its technical Appendices. Typically the fuel fabrication price is taken as the main economy indicator; nevertheless also many other financial and technical features of the contract must be taken into account in order to reach the best price of electricity sold into public energy grid. Our experience from several international tenders shows that the consistent complex of commercial and technical parameters of the contract is necessary to achieve optimal economic results and prepare proper conditions for advanced fuel cycle technology. Among those essential characteristics are payment conditions and schedule and extent of vendor's services and assistance to the operator. Very important role play also technical parameters, as safety and operational limits, influencing loading pattern quality and operating flexibility. Obviously also a level of operator's fuel cycle technology is a crucial point that is necessary for usage of technical quality of the fuel at the power plant. The final electricity price, produced by the plant, and uranium consumption are the only objective criteria to evaluate economic level of the fuel contract and the fuel cycle at all (Authors)

Light-Duty Vehicle CO2 and Fuel Economy Trends

Science.gov (United States)

This report provides data on the fuel economy, carbon dioxide (CO2) emissions, and technology trends of new light-duty vehicles (cars, minivans, sport utility vehicles, and pickup trucks) for model years 1975 to present in the United States.

Optimal Battery Utilization Over Lifetime for Parallel Hybrid Electric Vehicle to Maximize Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Patil, Chinmaya; Naghshtabrizi, Payam; Verma, Rajeev; Tang, Zhijun; Smith, Kandler; Shi, Ying

2016-08-01

This paper presents a control strategy to maximize fuel economy of a parallel hybrid electric vehicle over a target life of the battery. Many approaches to maximizing fuel economy of parallel hybrid electric vehicle do not consider the effect of control strategy on the life of the battery. This leads to an oversized and underutilized battery. There is a trade-off between how aggressively to use and 'consume' the battery versus to use the engine and consume fuel. The proposed approach addresses this trade-off by exploiting the differences in the fast dynamics of vehicle power management and slow dynamics of battery aging. The control strategy is separated into two parts, (1) Predictive Battery Management (PBM), and (2) Predictive Power Management (PPM). PBM is the higher level control with slow update rate, e.g. once per month, responsible for generating optimal set points for PPM. The considered set points in this paper are the battery power limits and State Of Charge (SOC). The problem of finding the optimal set points over the target battery life that minimize engine fuel consumption is solved using dynamic programming. PPM is the lower level control with high update rate, e.g. a second, responsible for generating the optimal HEV energy management controls and is implemented using model predictive control approach. The PPM objective is to find the engine and battery power commands to achieve the best fuel economy given the battery power and SOC constraints imposed by PBM. Simulation results with a medium duty commercial hybrid electric vehicle and the proposed two-level hierarchical control strategy show that the HEV fuel economy is maximized while meeting a specified target battery life. On the other hand, the optimal unconstrained control strategy achieves marginally higher fuel economy, but fails to meet the target battery life.

Decomposing Fuel Economy and Greenhouse Gas Regulatory Standards in the Energy Conversion Efficiency and Tractive Energy Domain

Energy Technology Data Exchange (ETDEWEB)

Pannone, Greg [Novation Analytics; Thomas, John F [ORNL; Reale, Michael [Novation Analytics; Betz, Brian [Novation Analytics

2017-01-01

The three foundational elements that determine mobile source energy use and tailpipe carbon dioxide (CO2) emissions are the tractive energy requirements of the vehicle, the on-cycle energy conversion efficiency of the propulsion system, and the energy source. The tractive energy requirements are determined by the vehicle's mass, aerodynamic drag, tire rolling resistance, and parasitic drag. Oncycle energy conversion of the propulsion system is dictated by the tractive efficiency, non-tractive energy use, kinetic energy recovery, and parasitic losses. The energy source determines the mobile source CO2 emissions. For current vehicles, tractive energy requirements and overall energy conversion efficiency are readily available from the decomposition of test data. For future applications, plausible levels of mass reduction, aerodynamic drag improvements, and tire rolling resistance can be transposed into the tractive energy domain. Similarly, by combining thermodynamic, mechanical efficiency, and kinetic energy recovery fundamentals with logical proxies, achievable levels of energy conversion efficiency can be established to allow for the evaluation of future powertrain requirements. Combining the plausible levels of tractive energy and on-cycle efficiency provides a means to compute sustainable vehicle and propulsion system scenarios that can achieve future regulations. Using these principles, the regulations established in the United States (U.S.) for fuel consumption and CO2 emissions are evaluated. Fleet-level scenarios are generated and compared to the technology deployment assumptions made during rule-making. When compared to the rule-making assumptions, the results indicate that a greater level of advanced vehicle and propulsion system technology deployment will be required to achieve the model year 2025 U.S. standards for fuel economy and CO2 emissions.

Survey evidence on the willingness of U.S. consumers to pay for automotive fuel economy

International Nuclear Information System (INIS)

Greene, David L.; Evans, David H.; Hiestand, John

2013-01-01

Prospect theory holds that human beings faced with a risky bet will tend to value potential losses about twice as much as potential gains. Previous research has demonstrated that prospect theory could be sufficient to explain an energy paradox in the market for automotive fuel economy. This paper analyzes data from questions added to four commercial, multi-client surveys of 1000 U.S. households each in 2004, 2011, 2012 and 2013. Households were asked about willingness to pay for future fuel savings as well as the annual fuel savings necessary to justify a given upfront payment. Payback periods inferred from household responses are generally consistent over time and across different formulations of questions. Mean calculated payback periods are about 3 years, but there is substantial dispersion among individual responses. The calculated payback periods do not appear to be correlated with the attributes of respondents. Respondents were able to quantitatively describe their uncertainty about both vehicle fuel economy and future fuel prices. Simulation of loss averse behavior based on respondents’ stated uncertainty illustrates how loss aversion could lead consumers to substantially undervalue future fuel savings relative to their expected value. - Highlights: • Payback periods were calculated from stated willingness to pay for fuel savings in 4 US surveys. • US car buyers expect payback in 3 years in order to pay more for increased fuel economy. • Respondents’ payback periods are uncorrelated with their socio-economic attributes. • Survey respondents consider fuel economy ratings and future fuel prices highly uncertain. • The survey results are consistent with the behavioral economic principle of loss aversion

Development of fuel economy 5W-20 gasoline engine oil; Teinenpi 5W-20 gasoline engine yu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Akiyama, K; Ueda, F; Kurono, K; Kawai, H; Sugiyama, S [Toyota Motor Corp., Aichi (Japan)

1997-10-01

A 5W-20 gasoline engine oil which improves vehicle fuel efficiency by more than 1.5% relative to a conventional 5W-30 gasoline engine oil was newly developed. Its high fuel economy performance lasts 10,000 km. The viscosity was optimized to satisfy both fuel economy and antiwear performances. Thiadiazole was used to retain the initial fuel economy performance provided by MoDTC. 5 refs., 7 figs., 2 tabs.

Evaluating the Impact of Road Grade on Simulated Commercial Vehicle Fuel Economy Using Real-World Drive Cycles

Energy Technology Data Exchange (ETDEWEB)

Lopp, Sean; Wood, Eric; Duran, Adam

2015-10-13

Commercial vehicle fuel economy is known to vary significantly with both positive and negative road grade. Medium- and heavy-duty vehicles operating at highway speeds require incrementally larger amounts of energy to pull heavy payloads up inclines as road grade increases. Non-hybrid vehicles are then unable to recapture energy on descent and lose energy through friction braking. While the on-road effects of road grade are well understood, the majority of standard commercial vehicle drive cycles feature no climb or descent requirements. Additionally, existing literature offers a limited number of sources that attempt to estimate the on-road energy implications of road grade in the medium- and heavy-duty space. This study uses real-world commercial vehicle drive cycles from the National Renewable Energy Laboratory's Fleet DNA database to simulate the effects of road grade on fuel economy across a range of vocations, operating conditions, and locations. Drive-cycles are matched with vocation-specific vehicle models and simulated with and without grade. Fuel use due to grade is presented, and variation in fuel consumption due to drive cycle and vehicle characteristics is explored through graphical and statistical comparison. The results of this study suggest that road grade accounts for 1%-9% of fuel use in commercial vehicles on average and up to 40% on select routes.

Particle swarm optimization of driving torque demand decision based on fuel economy for plug-in hybrid electric vehicle

International Nuclear Information System (INIS)

Shen, Peihong; Zhao, Zhiguo; Zhan, Xiaowen; Li, Jingwei

2017-01-01

In this paper, an energy management strategy based on logic threshold is proposed for a plug-in hybrid electric vehicle. The plug-in hybrid electric vehicle powertrain model is established using MATLAB/Simulink based on experimental tests of the power components, which is validated by the comparison with the verified simulation model which is built in the AVL Cruise. The influence of the driving torque demand decision on the fuel economy of plug-in hybrid electric vehicle is studied using a simulation. The optimization method for the driving torque demand decision, which refers to the relationship between the accelerator pedal opening and driving torque demand, from the perspective of fuel economy is formulated. The dynamically changing inertia weight particle swarm optimization is used to optimize the decision parameters. The simulation results show that the optimized driving torque demand decision can improve the PHEV fuel economy by 15.8% and 14.5% in the fuel economy test driving cycle of new European driving cycle and worldwide harmonized light vehicles test respectively, using the same rule-based energy management strategy. The proposed optimization method provides a theoretical guide for calibrating the parameters of driving torque demand decision to improve the fuel economy of the real plug-in hybrid electric vehicle. - Highlights: • The influence of the driving torque demand decision on the fuel economy is studied. • The optimization method for the driving torque demand decision is formulated. • An improved particle swarm optimization is utilized to optimize the parameters. • Fuel economy is improved by using the optimized driving torque demand decision.

Fuel Economy Impacts of Manual, Conventional Cruise Control, and Predictive Eco-Cruise Control Driving

Directory of Open Access Journals (Sweden)

Sangjun Park

2013-09-01

Full Text Available The paper presents the results of a field experiment that was designed to compare manual driving, conventional cruise control (CCC driving, and Eco-cruise control (ECC driving with regard to fuel economy. The field experiment was conducted on five test vehicles along a section of Interstate 81 that was comprised of ±4% uphill and downhill grade sections. Using an Onboard Diagnostic II reader, instantaneous fuel consumption rates and other driving parameters were collected with and without the CCC system enabled. The collected data were compared with regard to fuel economy, throttle control, and travel time. The results demonstrate that CCC enhances vehicle fuel economy by 3.3 percent on average relative to manual driving, however this difference was not found to be statistically significant at a 5 percent significance level. The results demonstrate that CCC driving is more efficient on downhill versus uphill sections. In addition, the study demonstrates that an ECC system can produce fuel savings ranging between 8 and 16 percent with increases in travel times ranging between 3 and 6 percent. These benefits appear to be largest for heavier vehicles (SUVs.

US Department of Energy Hybrid Electric Vehicle Battery and Fuel Economy Testing

Science.gov (United States)

Karner, Donald; Francfort, James

The advanced vehicle testing activity (AVTA), part of the US Department of Energy's FreedomCAR and Vehicle Technologies Program, has conducted testing of advanced technology vehicles since August 1995 in support of the AVTA goal to provide benchmark data for technology modelling, and research and development programs. The AVTA has tested over 200 advanced technology vehicles including full-size electric vehicles, urban electric vehicles, neighborhood electric vehicles, and internal combustion engine vehicles powered by hydrogen. Currently, the AVTA is conducting a significant evaluation of hybrid electric vehicles (HEVs) produced by major automotive manufacturers. The results are posted on the AVTA web page maintained by the Idaho National Laboratory. Through the course of this testing, the fuel economy of HEV fleets has been monitored and analyzed to determine the 'real world' performance of their hybrid energy systems, particularly the battery. The initial fuel economy of these vehicles has typically been less than that determined by the manufacturer and also varies significantly with environmental conditions. Nevertheless, the fuel economy and, therefore, battery performance, has remained stable over the life of a given vehicle (160 000 miles).

The Impact of Drive Cycles and Auxiliary Power on Passenger Car Fuel Economy

Directory of Open Access Journals (Sweden)

Thomas Grube

2018-04-01

Full Text Available In view of the advancement of zero emission transportation and current discussions on the reliability of nominal passenger car fuel economy, this article considers the procedure for assessing the potential for reducing the fuel consumption of passenger cars by using electric power to operate them. The analysis compares internal combustion engines, hybrid and fully electric concepts utilizing batteries and fuel cells. The starting point for the newly developed, simulation-based fuel consumption analysis is a longitudinal vehicle model. Mechanical power requirements on the drive side incorporate a large variety of standardized drive cycles to simulate typical patterns of car usage. The power requirements of electric heating and air conditioning are also included in the simulation, as these are especially relevant to electric powertrains. Moreover, on-board grid-load profiles are considered in the assessment. Fuel consumption is optimized by applying concept-specific operating strategies. The results show that the combination of low average driving speed and elevated onboard power requirements have severe impacts on the fuel efficiency of all powertrain configurations analyzed. In particular, the operational range of battery-electric vehicles is strongly affected by this due to the limited storage capacity of today’s batteries. The analysis confirms the significance of considering different load patterns of vehicle usage related to driving profiles and onboard electrical and thermal loads.

Is self-repayment of the nuclear fuel cycle plants profitable for national economy?

International Nuclear Information System (INIS)

Shevelev, Ya.V.

1991-01-01

The nuclear fuel cycle (NFC) plants should not be repaying in the optimal plan of nuclear economy development. Their losses are overlapped by superprofits of energy consumers. The loss in the national economy resulting from compulsory conversion of the NFC plants to self-repayment is estimated. 12 refs

40 CFR 600.206-08 - Calculation and use of FTP-based and HFET-based fuel economy values for vehicle configurations.

Science.gov (United States)

2010-07-01

... EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures... economy value exists for an electric vehicle configuration, all values for that vehicle configuration are... HFET-based fuel economy values for vehicle configurations. 600.206-08 Section 600.206-08 Protection of...

Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends Data

Data.gov (United States)

U.S. Environmental Protection Agency — The Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends report is the authoritative reference for carbon dioxide (CO2) emissions,...

40 CFR 600.307-86 - Fuel economy label format requirements.

Science.gov (United States)

2010-07-01

... metering system, including number of carburetor barrels, if applicable; (7) Transmission class; (8... Regulations for 1977 and Later Model Year Automobiles-Labeling § 600.307-86 Fuel economy label format... the city and highway estimates by 0.85, then rounding to the next lower integer value. (2) The upper...

Development & optimization of a rule-based energy management strategy for fuel economy improvement in hybrid electric vehicles

Science.gov (United States)

Asfoor, Mostafa

The gradual decline of oil reserves and the increasing demand for energy over the past decades has resulted in automotive manufacturers seeking alternative solutions to reduce the dependency on fossil-based fuels for transportation. A viable technology that enables significant improvements in the overall energy conversion efficiencies is the hybridization of conventional vehicle drive systems. This dissertation builds on prior hybrid powertrain development at the University of Idaho. Advanced vehicle models of a passenger car with a conventional powertrain and three different hybrid powertrain layouts were created using GT-Suite. These different powertrain models were validated against a variety of standard driving cycles. The overall fuel economy, energy consumption, and losses were monitored, and a comprehensive energy analysis was performed to compare energy sources and sinks. The GT-Suite model was then used to predict the formula hybrid SAE vehicle performance. Inputs to this model were a numerically predicted engine performance map, an electric motor torque curve, vehicle geometry, and road load parameters derived from a roll-down test. In this case study, the vehicle had a supervisory controller that followed a rule-based energy management strategy to insure a proper power split during hybrid mode operation. The supervisory controller parameters were optimized using discrete grid optimization method that minimized the total amount of fuel consumed during a specific urban driving cycle with an average speed of approximately 30 [mph]. More than a 15% increase in fuel economy was achieved by adding supervisory control and managing power split. The vehicle configuration without the supervisory controller displayed a fuel economy of 25 [mpg]. With the supervisory controller this rose to 29 [mpg]. Wider applications of this research include hybrid vehicle controller designs that can extend the range and survivability of military combat platforms. Furthermore, the

Development of the fuel and energy complex within the less demanding variant of Czechoslovak economy till 2000

International Nuclear Information System (INIS)

Kopac, P.; Blaha, J.; Maly, M.

1989-01-01

The character of the fuel and energy complex which has to serve national economy, requires that it be developed according to the needs and possibilities of national economy. A projection of social and economic development of Czechoslovakia till 2000 was set up by the Central Institute of National Economy Research and it was used as the basis of a scenario of the development of the fuel and energy complex. The results are given of modeling the development of the complex. (author). 6 tabs., 3 refs

75 FR 37733 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Science.gov (United States)

2010-06-30

... Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program AGENCY... direct final rule to amend the Renewable Fuel Standard program requirements on May 10, 2010. Because EPA... Fuel Standard program requirements, published on May 10, 2010. We stated in that direct final rule that...

Public Policy Issues in Transport. Taxes and standards for energy security and greenhouse gas objectives

Energy Technology Data Exchange (ETDEWEB)

Eskeland, Gunnar (Cicero, Oslo (Norway))

2008-07-01

The direct case for fuel economy standards on a stand alone basis dies in the textbook on the basis of first principles: the fuel tax is a better targeted instrument. In practice, the fuel economy standard, is killed by the 'rebound effect'. Vehicle users will, once they have more fuel efficient vehicles, respond to lower marginal costs by increased vehicle use. If an important part of negative externalities from transport are associated with vehicle kilometres (accidents, congestion, road wear) rather than fuel consumption, the rebound effect increases negative externalities from transport. The more direct way of addressing negative externalities from transport is to increase fuel taxes, and depending on their prior level, this is our first recommendation. But higher fuel taxes often raise political resistance. The fuel efficiency of existing cars is an important way by which people have adapted to present fuel taxes, determining their resistance to increases. A higher fuel efficiency standard is an instrument that faces little political resistance and which - over time - reduces the political resistance to increased fuel taxes. In efforts to reduce the fuel intensity of an economy, this interplay between an activity's fuel intensity, like gallons per vehicle mile, and the activity level, vehicle miles travelled or transported, nicely illustrates some important empirical questions and public policy issues: i) the first best policy proposition to reduce fuel related externalities is fuel taxes. Indeed, at the right level of fuel taxes, the externalities are zero: they are internalized. ii) the part of an economy's ability to shed fuel consumption lies in increased fuel efficiency in the individual activities, and this part can be stimulated with fuel efficiency standards. The other part, the activity level, should then be addressed with fuel tax increases. iv) We speculate that it may be difficult credibly to raise expected fuel taxes more than

Reduction in global warming due to fuel economy improvements and emissions control of criteria pollutants: New US light-duty vehicles (1968--1991)

Energy Technology Data Exchange (ETDEWEB)

Pitstick, M.E.; Santini, D.J. [Argonne National Lab., IL (United States); Chauhan, H. [Delaware Univ., Newark, DE (United States). Dept. of Civil Engineering

1992-08-01

This paper explores the impact of US emission controls and fuel economy improvements on the global warming potential (GWP) of new light-duty vehicles. Fuel economy improvements have reduced the GWP of both passenger cars and light-duty trucks by lowering the per mile emissions of carbon dioxide (CO{sub 2}). Further GWP reductions have been achieved by emission standards for criteria pollutants: carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NO{sub x}). The GWP of a criteria pollutant was calculated by multiplying the emission rate by a relative global warming factor to obtain a CO{sub 2} equivalent emission rate. Both CO{sub 2} and criteria pollutant emission rates per vehicle have decreased substantially for new light-duty vehicles over the period from 1968 to 1991. Over that period, the GWP from CO{sub 2} was reduced by almost 50% in new vehicles by improving fuel economy. In that same time period, the GWP from criteria pollutants from new vehicles was reduced with emission controls by from 80% to 90% depending on the global warming time frame of interest. Consequently, total reductions in the GWP of new passenger cars and light-duty trucks have been on the order of 55 to 75 percent compared to precontrol (before 1968) new vehicles. However, the reduction in GWP caused by emission control of criteria pollutants has been larger than the reduction caused by improved fuel economy (i.e., reduced CO{sub 2}). The contribution of criteria pollutants to the GWP of precontrol new vehicles was substantial, but their contribution has been reduced significantly due to US emission controls. As a result, the contribution of criteria pollutants to global warming is now much less than the contribution of CO{sub 2} from fuel consumption.

Reduction in global warming due to fuel economy improvements and emissions control of criteria pollutants: New US light-duty vehicles (1968--1991)

Energy Technology Data Exchange (ETDEWEB)

Pitstick, M.E.; Santini, D.J. (Argonne National Lab., IL (United States)); Chauhan, H. (Delaware Univ., Newark, DE (United States). Dept. of Civil Engineering)

1992-01-01

This paper explores the impact of US emission controls and fuel economy improvements on the global warming potential (GWP) of new light-duty vehicles. Fuel economy improvements have reduced the GWP of both passenger cars and light-duty trucks by lowering the per mile emissions of carbon dioxide (CO{sub 2}). Further GWP reductions have been achieved by emission standards for criteria pollutants: carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NO{sub x}). The GWP of a criteria pollutant was calculated by multiplying the emission rate by a relative global warming factor to obtain a CO{sub 2} equivalent emission rate. Both CO{sub 2} and criteria pollutant emission rates per vehicle have decreased substantially for new light-duty vehicles over the period from 1968 to 1991. Over that period, the GWP from CO{sub 2} was reduced by almost 50% in new vehicles by improving fuel economy. In that same time period, the GWP from criteria pollutants from new vehicles was reduced with emission controls by from 80% to 90% depending on the global warming time frame of interest. Consequently, total reductions in the GWP of new passenger cars and light-duty trucks have been on the order of 55 to 75 percent compared to precontrol (before 1968) new vehicles. However, the reduction in GWP caused by emission control of criteria pollutants has been larger than the reduction caused by improved fuel economy (i.e., reduced CO{sub 2}). The contribution of criteria pollutants to the GWP of precontrol new vehicles was substantial, but their contribution has been reduced significantly due to US emission controls. As a result, the contribution of criteria pollutants to global warming is now much less than the contribution of CO{sub 2} from fuel consumption.

Reduction in global warming due to fuel economy improvements and emissions control of criteria pollutants: New US light-duty vehicles (1968--1991)

International Nuclear Information System (INIS)

Pitstick, M.E.; Santini, D.J.; Chauhan, H.

1992-01-01

This paper explores the impact of US emission controls and fuel economy improvements on the global warming potential (GWP) of new light-duty vehicles. Fuel economy improvements have reduced the GWP of both passenger cars and light-duty trucks by lowering the per mile emissions of carbon dioxide (CO 2 ). Further GWP reductions have been achieved by emission standards for criteria pollutants: carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NO x ). The GWP of a criteria pollutant was calculated by multiplying the emission rate by a relative global warming factor to obtain a CO 2 equivalent emission rate. Both CO 2 and criteria pollutant emission rates per vehicle have decreased substantially for new light-duty vehicles over the period from 1968 to 1991. Over that period, the GWP from CO 2 was reduced by almost 50% in new vehicles by improving fuel economy. In that same time period, the GWP from criteria pollutants from new vehicles was reduced with emission controls by from 80% to 90% depending on the global warming time frame of interest. Consequently, total reductions in the GWP of new passenger cars and light-duty trucks have been on the order of 55 to 75 percent compared to precontrol (before 1968) new vehicles. However, the reduction in GWP caused by emission control of criteria pollutants has been larger than the reduction caused by improved fuel economy (i.e., reduced CO 2 ). The contribution of criteria pollutants to the GWP of precontrol new vehicles was substantial, but their contribution has been reduced significantly due to US emission controls. As a result, the contribution of criteria pollutants to global warming is now much less than the contribution of CO 2 from fuel consumption

Global warming and urban smog: Cost-effectiveness of CAFE standards and alternative fuels

International Nuclear Information System (INIS)

Krupnick, A.J.; Walls, M.A.; Collins, C.T.

1993-01-01

In this paper we estimate the cost-effectiveness, in terms of reducing greenhouse gas emissions, of increasing the corporate average fuel economy (CAFE) standard to 38 miles per gallon and substituting methanol, compressed natural gas (CNG), and reformulated gasoline for conventional gasoline. Greenhouse gas emissions are assessed over the entire fuel cycle and include carbon dioxide, methane, carbon monoxide, and nitrous oxide emissions. To account for joint environmental benefits, the cost per ton of greenhouse gas reduced is adjusted for reductions in volatile organic compound (VOC) emissions, an ozone precursor. CNG is found to be the most cost-effective of these alternatives, followed by increasing the CAFE standard, substituting methanol for gasoline, and substituting reformulated for conventional gasoline. Including the VOC benefits does not change the ranking of the alternatives, but does make the alternative fuels look better relative to increasing the CAFE standard. None of the alternatives look cost-effective should a carbon tax of $35 per ton be passed, and only CNG under optimistic assumptions looks cost-effective with a tax of $100 per ton of carbon. 35 refs., 4 figs., 6 tabs

76 FR 37703 - Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards; Public Hearing

Science.gov (United States)

2011-06-28

... Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards; Public Hearing AGENCY: Environmental... hearing to be held for the proposed rule ``Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel... be proposing amendments to the renewable fuel standard program regulations to establish annual...

Fuel Economy Improvement Potential of a Heavy Duty Truck using V2x Communication

Energy Technology Data Exchange (ETDEWEB)

LaClair, Tim J [ORNL; Verma, Rajeev [Eaton Corporation; Norris, Sarah [Eaton Corporation; Cochran, Robert [Eaton Corporation

2014-01-01

In this paper, we introduce an intelligent driver assistance system to reduce fuel consumption in heavy duty vehicles irrespective of the driving style of the driver. We specifically study the potential of V2I and V2V communications to reduce fuel consumption in heavy duty trucks. Most ITS communications today are oriented towards vehicle safety, with communications strategies and hardware that tend to focus on low latency. This has resulted in technologies emerging with a relatively limited range for the communications. For fuel economy, it is expected that most benefits will be derived with greater communications distances, at the scale of many hundred meters or several kilometers, due to the large inertia of heavy duty vehicles. It may therefore be necessary to employ different communications strategies for ITS applications aimed at fuel economy and other environmental benefits than what is used for safety applications in order to achieve the greatest benefits.

78 FR 12005 - Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing

Science.gov (United States)

2013-02-21

... Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing AGENCY: Environmental... EPA is announcing a public hearing to be held for the proposed rule ``Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards,'' which was published separately in the Federal Register on...

On the baseline evolution of automobile fuel economy in Europe

International Nuclear Information System (INIS)

Zachariadis, Theodoros

2006-01-01

'Business as usual' scenarios in long-term energy forecasts are crucial for scenario-based policy analyses. This article focuses on fuel economy of passenger cars and light trucks, a long-disputed issue with serious implications for worldwide energy use and CO 2 emissions. The current status in Europe is explained and future developments are analysed with the aid of historical data of the last three decades from the United States and Europe. As a result of this analysis, fuel economy values are proposed for use as assumptions in baseline energy/transport scenarios in the 15 'old' European Union Member States. Proposed values are given for new gasoline and diesel cars and for the years 2010, 2020 and 2030. The increasing discrepancy between vehicle fuel consumption measured under test conditions and that in the real world is also considered. One main conclusion is that the European Commission's voluntary agreement with the automobile industry should not be assumed to fully achieve its target under baseline conditions, nor should it be regarded as a major stimulus for autonomous vehicle efficiency improvements after 2010. A second conclusion is that three very recent studies enjoying authority across the EU tend to be overly optimistic as regards the technical progress for conventional and alternative vehicle propulsion technologies under 'business as usual' conditions

Trade, Development, and the Political Economy of Public Standards

OpenAIRE

Swinnen, Johan F.M.; Vandemoortele, Thijs

2009-01-01

This paper presents a political economy model of public standards in an open economy model. We use the model to derive the political optimum and to analyze different factors that have an influence on this political equilibrium. The paper discusses how the level of development influences the political equilibrium. We also analyze the relation between trade and the political equilibrium and compare this political outcome with the social optimum to identify under which cases ‘under-standardizati...

Simulations of the Fuel Economy and Emissions of Hybrid Transit Buses over Planned Local Routes

Energy Technology Data Exchange (ETDEWEB)

Gao, Zhiming [ORNL; LaClair, Tim J [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL; Franzese, Oscar [ORNL

2014-01-01

We present simulated fuel economy and emissions city transit buses powered by conventional diesel engines and diesel-hybrid electric powertrains of varying size. Six representative city drive cycles were included in the study. In addition, we included previously published aftertreatment device models for control of CO, HC, NOx, and particulate matter (PM) emissions. Our results reveal that bus hybridization can significantly enhance fuel economy by reducing engine idling time, reducing demands for accessory loads, exploiting regenerative braking, and shifting engine operation to speeds and loads with higher fuel efficiency. Increased hybridization also tends to monotonically reduce engine-out emissions, but trends in the tailpipe (post-aftertreatment) emissions involve more complex interactions that significantly depend on motor size and drive cycle details.

40 CFR 600.207-08 - Calculation and use of vehicle-specific 5-cycle-based fuel economy values for vehicle...

Science.gov (United States)

2010-07-01

...-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year... for each vehicle under § 600.114-08 and as approved in § 600.008-08 (c), are used to determine vehicle... fuel economy value exists for an electric vehicle configuration, all values for that vehicle...

Interactions between California's Low Carbon Fuel Standard and the National Renewable Fuel Standard

International Nuclear Information System (INIS)

Whistance, Jarrett; Thompson, Wyatt; Meyer, Seth

2017-01-01

This study investigates the economic interactions between a national renewable fuel policy, namely the Renewable Fuel Standard (RFS) in the United States, and a sub-national renewable fuel policy, the Low Carbon Fuel Standard (LCFS) in California. The two policies have a similar objective of reducing greenhouse gas emissions, but the policies differ in the manner in which those objectives are met. The RFS imposes a hierarchical mandate of renewable fuel use for each year whereas the LCFS imposes a specific annual carbon-intensity reduction with less of a fuel specific mandate. We model the interactions using a partial-equilibrium structural model of agricultural and energy markets in the US and Rest-of-World regions. Our results suggest the policies are mutually reinforcing in that the compliance costs of meeting one of the requirements is lower in the presence of the other policy. In addition, the two policies combine to create a spatial shift in renewable fuel use toward California even though overall renewable fuel use remains relatively unchanged. - Highlights: • Results suggest the RFS and LCFS are mutually reinforcing. • Overall level of renewable fuel use is similar across scenarios. • Renewable fuel use shifts toward California in the presence of the LCFS. • Higher ethanol blend (e.g. E85) use also shifts toward California.

Household cooking fuels and technologies in developing economies

International Nuclear Information System (INIS)

Foell, Wesley; Pachauri, Shonali; Spreng, Daniel; Zerriffi, Hisham

2011-01-01

A major energy challenge of the 21st century is the health and welfare of 2.7 billion people worldwide, who currently rely on burning biomass in traditional household cooking systems. This Special Issue on Clean Cooking Fuels and Technologies in Developing Economies builds upon an IAEE workshop on this subject, held in Istanbul in 2008. It includes several papers from that workshop plus papers commissioned afterwards. The major themes of that workshop and this Special Issue are: •Analytical and decision frameworks for analysis and policy development for clean cooking fuels. •Making energy provisioning a central component of development strategies. •Strategies/business models of suppliers of modern fuels and technologies. •Analysis of successes/failures of past policies and programs to improve access to clean cooking. This introductory paper serves as a preamble to the 11 papers in this Special Issue. It provides a brief background on household cooking fuels and technologies, including: (1) their implications for sustainable development, health and welfare, gender impacts, and environment/climate issues; (2) options and scenarios for improved household cooling systems; and (3) discussions of institutions, programs and markets. It closes with “Research and Action Agendas”, initially developed during the 2008 workshop.

Fueling Wisconsin's economy with renewable energy

International Nuclear Information System (INIS)

Clemmer, S.

1995-01-01

A dynamic macroeconomic model of the Wisconsin economy is used to estimate the economic impacts of displacing a portion of future investment in fossil fuel power plants (coal and natural gas) with renewable energy resources (biomass, wind, solar and hydro). The results show that renewable energy investments produce over three times more jobs, income and economic activity than the same amount of electricity generated from coal and natural gas power plants. Between 1995 and 2020, a 75% increase in renewable energy use generates approximately 65,000 more job-years of employment, $1.6 billion in higher disposable income and a $3.1 billion increase in gross regional product than conventional power plant investments. This includes the effects of a 0.3% average annual increase in electricity prices from renewable energy investments

77 FR 72746 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard and Diesel...

Science.gov (United States)

2012-12-06

... Fuels and Fuel Additives: Modifications to Renewable Fuel Standard and Diesel Sulfur Programs AGENCY... Fuel Standard (``RFS'') program under section 211(o) of the Clean Air Act. The direct final rule also... marine diesel fuel produced by transmix processors, and the fuel marker requirements for 500 ppm sulfur...

Standardization of Alternative Fuels. Phase 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-08-15

mean with a specific alternative fuel; a standard for the fuel. Since we today live in a global society with international trade, the work with standards has to be carried out by international standardization organizations such as CEN and ISO. In the work on standardization of alternative fuels, it is of course important that all existing knowledge and experiences on production, distribution and use of alternative fuels are taken into account to avoid duplication of work and to limit the time and resources needed to produce standards. The International Energy Agency's Implementing Agreement on Advanced Motor Fuels, (IEA/AMF) is an organization with competence and more than 20 years of experience on alternative fuels. In April 2002 IEA/AMF's Executive Committee decided to start a new Annex, Annex XXVII on 'Standardization of alternative fuels'. This report is the result of phase one of Annex XXVII.

Interaction of carbon reduction and green energy promotion in a small fossil-fuel importing economy

International Nuclear Information System (INIS)

Pethig, Ruediger; Wittlich, Christian

2009-01-01

We study the incidence of carbon-reduction and green-energy promotion policies in an open fossil-fuel importing general equilibrium economy. The focus is on mixed price-based or quantity-based policies. Instruments directed toward promoting green energy are shown to reduce also carbon emissions and vice versa. Their direct effects are stronger than their side effects, the more so, the greater is the elasticity of substitution in consumption between energy and the consumption good. We calculate the effects of variations in individual policy parameters, especially on energy prices and welfare costs, and determine the impact of exogenous fossil-fuel price shocks on the economy. (orig.)

Impact of Friction Reduction Technologies on Fuel Economy for Ground Vehicles

Science.gov (United States)

2009-08-13

UNCLAS: Dist A. Approved for public release IMPACT OF FRICTION REDUCTION TECHNOLOGIES ON FUEL ECONOMY FOR GROUND VEHICLES G. R. Fenske , R. A. Erck...PROGRAM ELEMENT NUMBER 6. AUTHOR(S) G.R. Fenske ; R.A. Erck; O.O. Ajayi; A. Masoner’ A.S. Confort 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT

The Miller cycle effects on improvement of fuel economy in a highly boosted, high compression ratio, direct-injection gasoline engine: EIVC vs. LIVC

International Nuclear Information System (INIS)

Li, Tie; Gao, Yi; Wang, Jiasheng; Chen, Ziqian

2014-01-01

Highlights: • At high load, LIVC is superior over EIVC in improving fuel economy. • The improvement with LIVC is due to advanced combustion phasing and increased pumping work. • At low load, EIVC is better than LIVC in improving fuel economy. • Pumping loss with EIVC is smaller than with LIVC at low load. • But heat release rate with EIVC is slower than with LIVC. - Abstract: A combination of downsizing, highly boosting and direct injection (DI) is an effective way to improve fuel economy of gasoline engines without the penalties of reduced torque or power output. At high loads, however, knock problem becomes severer when increasing the intake boosting. As a compromise, geometric compression ratio (CR) is usually reduced to mitigate knock, and the improvement of fuel economy is discounted. Application of Miller cycle, which can be realized by either early or late intake valve closing (EIVC or LIVC), has the potential to reduce the effective CR and suppress knock. In this paper, the effects of EIVC and LIVC on the fuel economy of a boosted DI gasoline production engine reformed with a geometric CR of 12.0 are experimentally compared at low and high loads. Compared to the original production engine with CR 9.3, at the high load operation, the brake specific fuel consumption (BSFC) is improved by 4.7% with CR12.0 and LIVC, while the effect of EIVC on improving BSFC is negligibly small. At the low load operation, combined with CR12.0, LIVC and EIVC improve the fuel economy by 6.8% and 7.4%, respectively, compared to the production engine. The mechanism behind the effects of LIVC and EIVC on improving the fuel economy is discussed. These results will be a valuable reference for engine designers and researchers

Fuel Mix Impacts from Transportation Fuel Carbon Intensity Standards in Multiple Jurisdictions

Science.gov (United States)

Witcover, J.

2017-12-01

Fuel carbon intensity standards have emerged as an important policy in jurisdictions looking to target transportation greenhouse gas (GHG) emissions for reduction. A carbon intensity standard rates transportation fuels based on analysis of lifecycle GHG emissions, and uses a system of deficits and tradable, bankable credits to reward increased use of fuels with lower carbon intensity ratings while disincentivizing use of fuels with higher carbon intensity ratings such as conventional fossil fuels. Jurisdictions with carbon intensity standards now in effect include California, Oregon, and British Columbia, all requiring 10% reductions in carbon intensity of the transport fuel pool over a 10-year period. The states and province have committed to grow demand for low carbon fuels in the region as part of collaboration on climate change policies. Canada is developing a carbon intensity standard with broader coverage, for fuels used in transport, industry, and buildings. This study shows a changing fuel mix in affected jurisdictions under the policy in terms of shifting contribution of transportation energy from alternative fuels and trends in shares of particular fuel pathways. It contrasts program designs across the jurisdictions with the policy, highlights the opportunities and challenges these pose for the alternative fuel market, and discusses the impact of having multiple policies alongside federal renewable fuel standards and sometimes local carbon pricing regimes. The results show how the market has responded thus far to a policy that incentivizes carbon saving anywhere along the supply chain at lowest cost, in ways that diverged from a priori policy expectations. Lessons for the policies moving forward are discussed.

The economy of the nuclear fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Stoll, W [Alpha Chemie und Metallurgie G.m.b.H. (ALKEM), Hanau (Germany, F.R.)

1989-07-01

Heat extracted from nuclear fuel costs by a factor of 3 to 7 less than heat from conventional fossile fuel. So, nuclear fuel per se has an economical advantage, decreased however partly by higher nuclear plant investment costs. The standard LWR design does not allow all the fission energy stored in the fuel during on cycle to be used. It is therefore the most natural approach to separate fissionable species from fission products and consume them by fissioning. Whether this is economically justified as opposed by storing them indefinitely with spent fuel has widely been debated. The paper outlines the different approaches taken by nuclear communities worldwide and their perceived or proven rational arguments. It will balance economic and other factors for the near and distant future including advanced reactor concepts. The specific solution within the German nuclear programme will be explained, including foreseeable future trends. (orig.).

Vehicle energy management for on/off controlled auxiliaries : fuel economy vs. switching frequency

NARCIS (Netherlands)

Chen, H.; Kessels, J.T.B.A.; Weiland, S.

2015-01-01

In this paper, an integrated approach for designing energy management strategies concerning vehicle auxiliaries with on/off control is proposed. This approach provides the possibility of making different trade-offs between fuel economy and switching frequency. In this paper, we demonstrate the

Unemployment rate and price of gasoline predict the fuel economy of purchased new vehicles.

Science.gov (United States)

2011-03-01

This study examined the relationship between two economic indicatorsthe : unemployment rate and the price of gasolineand the fuel economy of purchased new : vehicles. A regression analysis was performed on U.S. monthly data from October 2007 : ...

40 CFR 600.206-12 - Calculation and use of FTP-based and HFET-based fuel economy and carbon-related exhaust emission...

Science.gov (United States)

2010-07-01

... POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for... vehicle under § 600.113(a) and (b) and as approved in § 600.008-08(c), are used to determine FTP-based... value exists for an electric vehicle configuration, that value, rounded to the nearest tenth of a mile...

Fuel cell commercialization: The key to a hydrogen economy

Science.gov (United States)

Zegers, P.

With the current level of global oil production, oil reserves will be sufficient for 40 years. However, due to the fact that the global GDP will have increased by a factor seven in 2050, oil reserves are likely to be exhausted in a much shorter time period. The EU and car industry aim at a reduction of the consumption of oil, at energy savings (with a key role for fuel cells) and an increased use of hydrogen from natural gas and, possibly, coal, in the medium term. The discovery of huge methane resources as methane hydrates (20 times those of oil, gas and coal together) in oceans at 1000-3000 m depth could be of major importance. In the long term, the EU aims at a renewable energy-based energy supply. The European Hydrogen and Fuel Cell Technology Platform is expected to play a major role in bringing about a hydrogen economy. The availability of commercial fuel cells is here a prerequisite. However, after many years of research, fuel cells have not yet been commercialized. If they will not succeed to enter the market within 5 years there is a real danger that activities aiming at a hydrogen society will peter out. In a hydrogen strategy, high priority should therefore be given to actions which will bring about fuel cell commercialization within 5 years. They should include the identification of fuel cell types and (niche) markets which are most favorable for a rapid market introduction. These actions should include focused short-term RTD aiming at cost reduction and increased reliability.

Assessment of effects of maturity of Japan`s economy and society and improvement in automotive fuel consumption on demand for automotive fuels; Nippon keizai shakai no seijukuka to nenpi kaizen ga jidoshayo nenryo juyo ni ataeru eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Shimomura, S. [The Institute of Energy Economics, Tokyo (Japan)

1998-04-01

This paper evaluates impacts of the maturity of Japan`s economy and society and the improvement in automotive fuel efficiency on the demand for automotive fuels by FY 2010. Standard case and lower order case were examined. When the traffic volume of passenger cars in FY 1995 is assumed to be 100, it become 121 and 119 in standard and lower order cases, respectively. The traffic volume of lorries become 106 and 102 in standard and lower order cases, respectively, which showed a rather small growth. Deterioration rate of the fuel consumption was estimated by considering the difference in fuel consumption of new cars and existing cars. Although the fuel consumption will be lowered by FY 2000 when the cassation rate of ordinary passenger cars will rapidly increase, the impact will be lowered after that. For lorries for commercial use, the running fuel consumption will be gradually lowered due to the increased carrying capacity and vehicle weight a lorry with improving the transportation efficiency. Decreased running speed by traffic jam is also a cause of the deterioration of fuel consumption. When a policy of improvement in the fuel consumption is promoted in a background of CO2 issues, the fuel consumption of each vehicle will be gradually improved. The peak of fuel demand will be in FY 2005 by considering the changes in economical and social structures and the improvement in fuel consumption for the environmental protection. 5 figs., 3 tabs.

Digital economy and non-standard work

Directory of Open Access Journals (Sweden)

Patrizia Tullini

2016-12-01

Full Text Available Public and scientific debate on the digital economy is now widespread in many european countries. Also labour law scholars started to pay more attention to the new economical models and to the impact of digital technologies on productive processes. Economics and labour sciences should now move from a descriptive analysis to a deeper theoretical elaboration.The directions of the theoretical analysis are essentially two: the first one deals with the overbearing diffusion of non-standard forms of work on the web, especially on the digital platforms. This trend undermines the traditional foundation of subordination and affects the dynamics of global labour law market. The second directions deals with the increasing use of artificial intelligence in the industrial environment that presents new legal and social issues, concerning both the replacement of standard work with robotics and the complementarity between human work and «non-human agents» work.

standards used for quality control of nuclear fuels

International Nuclear Information System (INIS)

Guereli, L; Can, S.

1997-01-01

Nuclear fuels and fuel materials are subject to stringent restrictions as to their quality. The standards and regulations that apply vary according to reactor type and country and the standards are stated in the quality assurance documents. The concept of quality assurance has altered the conventional quality control tests and procedures, defining which control tests are to be applied and how. Although most of the tests and measurements allow the determination of tolerances to be decided according to the agreement between the buyer and the seller, exacting procedures apply to which instruments and equipment are used for these tests and measurements, how these instruments are standardized.Detailed explanations of test methods and their documentation is a requirement in all standards. The purpose of this work is to study which standards, tests and measurements apply to the nuclear fuel production. Only the standards that apply to various stages of the nuclear fuel production (powder preparation, pellet production, fuel element and fuel assembly fabrication) are reviewed. Process and documentation control, design and licensing requirements and the frequency of inspections are quality assurance subjects. Some ASTM standards are given as examples

Gasoline prices, gasoline consumption, and new-vehicle fuel economy: Evidence for a large sample of countries

International Nuclear Information System (INIS)

Burke, Paul J.; Nishitateno, Shuhei

2013-01-01

Countries differ considerably in terms of the price drivers pay for gasoline. This paper uses data for 132 countries for the period 1995–2008 to investigate the implications of these differences for the consumption of gasoline for road transport. To address the potential for simultaneity bias, we use both a country's oil reserves and the international crude oil price as instruments for a country's average gasoline pump price. We obtain estimates of the long-run price elasticity of gasoline demand of between − 0.2 and − 0.5. Using newly available data for a sub-sample of 43 countries, we also find that higher gasoline prices induce consumers to substitute to vehicles that are more fuel-efficient, with an estimated elasticity of + 0.2. Despite the small size of our elasticity estimates, there is considerable scope for low-price countries to achieve gasoline savings and vehicle fuel economy improvements via reducing gasoline subsidies and/or increasing gasoline taxes. - Highlights: ► We estimate the determinants of gasoline demand and new-vehicle fuel economy. ► Estimates are for a large sample of countries for the period 1995–2008. ► We instrument for gasoline prices using oil reserves and the world crude oil price. ► Gasoline demand and fuel economy are inelastic with respect to the gasoline price. ► Large energy efficiency gains are possible via higher gasoline prices

Global warming and urban smog: The cost effectiveness of CAFE standards and alternative fuels

International Nuclear Information System (INIS)

Krupnick, A.J.; Walls, M.A.; Collins, C.T.

1992-01-01

This paper evaluates alternative transportation policies for reducing greenhouse gas emissions and ozone precursors. The net cost-effectiveness -- i.e., the cost per ton of greenhouse gas reduced, adjusted for ozone reduction benefits -- of substituting methanol, compressed natural gas (CNG), and reformulated gasoline for conventional gasoline is assessed and compared with the cost-effectiveness of raising the corporate average fuel economy (CAFE) standard to 38 miles per gallon. Computing this open-quotes netclose quotes cost-effectiveness is one way of measuring the joint environmental benefits that these alternatives provide. Greenhouse gas emissions are assessed over the entire fuel cycle and include not only carbon dioxide emissions, but also methane, carbon monoxide, and nitrous oxide emissions. In computing cost-effectiveness, we account for the so-called open-quotes rebound effectclose quotes -- the impact on vehicle-miles traveled of higher or lower fuel costs. CNG is found to be the most cost-effective of these alternatives, followed by increasing the CAFE standard, substituting methanol for gasoline, and substituting reformulated for conventional gasoline. Including the ozone reduction benefits does not change the rankings of the alternatives, but does make the alternative fuels look better relative to increasing the CAFE standard. Incorporating the rebound effect greatly changes the magnitude of the estimates but does not change the rankings of the alternatives. None of the alternatives look cost-effective should a carbon tax of $35 per ton be passes (the proposal in the Stark bill, H.R. 1086), and only CNG under optimistic assumptions looks cost-effective if a tax of $100 per ton of carbon is passed

Outlook on Standardization of Alternative Vehicle Fuels

Energy Technology Data Exchange (ETDEWEB)

Rehnlund, B [Atrax Energi AB (Sweden)

2008-10-15

The use of fossil but in first hand biobased alternative fuels in transportation has increased over the last decades. This change is primarily driven by concerns about climate change that is caused by emissions of fossil carbon dioxide and other greenhouse gases, but also by the impact on health and environment, caused by emissions of regulated as well as non-regulated emissions from the transport sector. Most alternative fuels will help to reduce the emissions of regulated and non-regulated emissions, while alternative fuels based on biomass also will contribute to reduced net emissions of carbon dioxide. Since the mid 1990s, the use of biomass based fuels such as ethanol and biodiesel has reached levels high enough in for example Europe, Brazil and the U.S. to motivate national or regional specifications/standards. Especially from the vehicle/engine manufacturer's point of view standards are of high importance. From early 2000 onwards, the international trade of biofuels (for example from Brazil to the U.S. and Europe) has grown, and this has created a need for common international specifications/standards. This report presents information about national and regional standards for alternative fuels, but also, when existing and reported, standards on a global level are described and discussed. Ongoing work concerning new or revised standards on alternative fuels on national, regional or global level is also discussed. In this report we have covered standards on all kind of alternative fuels, exemplified below. However, the focus is on liquid biofuels for diesel engines and Otto engines. 1) Liquid fuels for diesel engines (compression ignition engines), such as Fatty Acid Methyl Esters (FAME), Fatty Acid Ethyl Esters (FAEE), alcohols, alcohol derivates and synthetic diesel fuels. 2) Liquid fuels for Otto engines (spark ignition engines), such as alcohols, ethers and synthetic gasoline. 3) Liquefied fossil petroleum gas (LPG). 4) Di-Methyl Ether (DME). 5) Fossil

Outlook on Standardization of Alternative Vehicle Fuels

Energy Technology Data Exchange (ETDEWEB)

Rehnlund, B. [Atrax Energi AB (Sweden)

2008-10-15

The use of fossil but in first hand biobased alternative fuels in transportation has increased over the last decades. This change is primarily driven by concerns about climate change that is caused by emissions of fossil carbon dioxide and other greenhouse gases, but also by the impact on health and environment, caused by emissions of regulated as well as non-regulated emissions from the transport sector. Most alternative fuels will help to reduce the emissions of regulated and non-regulated emissions, while alternative fuels based on biomass also will contribute to reduced net emissions of carbon dioxide. Since the mid 1990s, the use of biomass based fuels such as ethanol and biodiesel has reached levels high enough in for example Europe, Brazil and the U.S. to motivate national or regional specifications/standards. Especially from the vehicle/engine manufacturer's point of view standards are of high importance. From early 2000 onwards, the international trade of biofuels (for example from Brazil to the U.S. and Europe) has grown, and this has created a need for common international specifications/standards. This report presents information about national and regional standards for alternative fuels, but also, when existing and reported, standards on a global level are described and discussed. Ongoing work concerning new or revised standards on alternative fuels on national, regional or global level is also discussed. In this report we have covered standards on all kind of alternative fuels, exemplified below. However, the focus is on liquid biofuels for diesel engines and Otto engines. 1) Liquid fuels for diesel engines (compression ignition engines), such as Fatty Acid Methyl Esters (FAME), Fatty Acid Ethyl Esters (FAEE), alcohols, alcohol derivates and synthetic diesel fuels. 2) Liquid fuels for Otto engines (spark ignition engines), such as alcohols, ethers and synthetic gasoline. 3) Liquefied fossil petroleum gas (LPG). 4) Di-Methyl Ether (DME). 5

The Role of Synthetic Fuels for a Carbon Neutral Economy

Directory of Open Access Journals (Sweden)

Rui Namorado Rosa

2017-04-01

Full Text Available Fossil fuels depletion and increasing environmental impacts arising from their use call for seeking growing supplies from renewable and nuclear primary energy sources. However, it is necessary to simultaneously attend to both the electrical power needs and the specificities of the transport and industrial sector requirements. A major question posed by the shift away from traditional fossil fuels towards renewable energy sources lies in matching the power demand with the daily and seasonal oscillation and the intermittency of these natural energy fluxes. Huge energy storage requirements become necessary or otherwise the decline of the power factor of both the renewable and conventional generation would mean loss of resources. On the other hand, liquid and gaseous fuels, for which there is vast storage and distribution capacity available, appear essential to supply the transport sector for a very long time ahead, besides their domestic and industrial roles. Within this context, the present assessment suggests that proven technologies and sound tested principles are available to develop an integrated energy system, relying on synthetic fuels. These would incorporate carbon capture and utilization in a closed carbon cycle, progressively relying mostly on solar and/or nuclear primary sources, providing both electric power and gaseous/liquid hydrocarbon fuels, having ample storage capacity, and able to timely satisfy all forms of energy demand. The principles and means are already available to develop a carbon-neutral synthetic fuel economy.

Investigation of the influence of physical and chemical properties of biodiesel in the fuel economy, energy and environmental performance of motor diesel

Directory of Open Access Journals (Sweden)

Korpach А.

2016-08-01

Full Text Available Due to exhaustion of world energy reserves and significant environmental pollution by harmful substances, current research aimed at determining the effectiveness of alternative fuels. In the article compare two samples of biodiesel and studied their physical and chemical properties accordance with International Standard. Effect of different samples of biodiesel in fuel economy, energy and environmental performance automotive diesel determined by the bench tests of 4CH11,0/12.5 (D-241 diesel. The difference between physical and chemical properties of two biodiesel samples influenced to the fuel efficiency and environmental performance of the diesel. Operation on biodiesel with higher density and kinematic viscosity provide increases of maximum power and torque and increase fuel consumption. It also increases the concentration of nitrogen oxides in exhaust gases and it opacity. The results allow evaluate how the deviation of physical and chemical properties of biodiesel could affect the operational performance of the engine.

Eco-driving : strategic, tactical, and operational decisions of the driver that improve vehicle fuel economy.

Science.gov (United States)

2011-08-01

"This report presents information about the effects of decisions that a driver can make to : influence on-road fuel economy of light-duty vehicles. These include strategic decisions : (vehicle selection and maintenance), tactical decisions (route sel...

76 FR 18066 - Regulation of Fuels and Fuel Additives: Changes to Renewable Fuel Standard Program

Science.gov (United States)

2011-04-01

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 80 Regulation of Fuels and Fuel Additives: Changes to Renewable Fuel Standard Program CFR Correction In Title 40 of the Code of Federal Regulations, Parts 72 to...-generating foreign producers and importers of renewable fuels for which RINs have been generated by the...

40 CFR 86.1709-99 - Exhaust emission standards for 1999 and later light light-duty trucks.

Science.gov (United States)

2010-07-01

... emissions measured on the federal Highway Fuel Economy Test in 40 CFR part 600, subpart B, shall be not.... Both the projected emissions and the Highway Fuel Economy Test standard shall be rounded to the nearest... effectiveness. A/C-on specific “open-loop” or “commanded enrichment” air-fuel enrichment strategies (as defined...

Estimate of Technical Potential for Minimum Efficiency Performance Standards in 13 Major World Economies

Energy Technology Data Exchange (ETDEWEB)

Letschert, Virginie [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Desroches, Louis-Benoit [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ke, Jing [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); McNeil, Michael [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-07-01

As part of the ongoing effort to estimate the foreseeable impacts of aggressive minimum efficiency performance standards (MEPS) programs in the world’s major economies, Lawrence Berkeley National Laboratory (LBNL) has developed a scenario to analyze the technical potential of MEPS in 13 major economies around the world1 . The “best available technology” (BAT) scenario seeks to determine the maximum potential savings that would result from diffusion of the most efficient available technologies in these major economies.

Efficiency Standard in automotive industry

International Nuclear Information System (INIS)

Goldoni, G.

2008-01-01

A technological transition in the transport sector could be only be possible with a convergence of objectives of the automotive and the fuel industries, which is not very simple to obtain. Fuel economy standards could differently reduce the growing trend of CO 2 emissions in this sector but regulators should avoid capture from domestic industry. [it

Does a renewable fuel standard for biofuels reduce climate costs?

Energy Technology Data Exchange (ETDEWEB)

Greaker, Mads; Hoel, Michael; Rosendahl, Knut Einar

2012-07-01

Recent contributions have questioned whether biofuels policies actually lead to emissions reductions, and thus lower climate costs. In this paper we make two contributions to the literature. First, we study the market effects of a renewable fuel standard. Opposed to most previous studies we model the supply of fossil fuels taking into account that fossil fuels is a non-renewable resource. Second, we model emissions from land use change explicitly when we evaluate the climate effects of the renewable fuel standard. We find that extraction of fossil fuels most likely will decline initially as a consequence of the standard. Thus, if emissions from biofuels are sufficiently low, the standard will have beneficial climate effects. Furthermore, we find that the standard tends to reduce total fuel (i.e., oil plus biofuels) consumption initially. Hence, even if emissions from biofuels are substantial, climate costs may be reduced. Finally, if only a subset of countries introduce a renewable fuel standard, there will be carbon leakage to the rest of the world. However, climate costs may decline as global extraction of fossil fuels is postponed.(Author)

Environmental, Economic, and Scalability Considerations and Trends of Selected Fuel Economy-Enhancing Biomass-Derived Blendstocks

Energy Technology Data Exchange (ETDEWEB)

Dunn, Jennifer B. [Systems; Biddy, Mary [National; Jones, Susanne [Energy; Cai, Hao [Systems; Benavides, Pahola Thathiana [Systems; Markham, Jennifer [National; Tao, Ling [National; Tan, Eric [National; Kinchin, Christopher [National; Davis, Ryan [National; Dutta, Abhijit [National; Bearden, Mark [Energy; Clayton, Christopher [Energy; Phillips, Steven [Energy; Rappé, Kenneth [Energy; Lamers, Patrick [Bioenergy

2017-10-30

24 biomass-derived compounds and mixtures, identified based on their physical properties, that could be blended into fuels to improve spark ignition engine fuel economy were assessed for their economic, technology readiness, and environmental viability. These bio-blendstocks were modeled to be produced biochemically, thermochemically, or through hybrid processes. To carry out the assessment, 17 metrics were developed for which each bio-blendstock was determined to be favorable, neutral, or unfavorable. Cellulosic ethanol was included as a reference case. Overall, bio-blendstock yields in biochemical processes were lower than in thermochemical processes, in which all biomass, including lignin, is converted to a product. Bio-blendstock yields were a key determinant in overall viability. Key knowledge gaps included the degree of purity needed for use as a bio-blendstock as compared to a chemical. Less stringent purification requirements for fuels could cut processing costs and environmental impacts. Additionally, more information is needed on the blendability of many of these bio-blendstocks with gasoline to support the technology readiness evaluation. Overall, the technology to produce many of these blendstocks from biomass is emerging and as it matures, these assessments must be revisited. Importantly, considering economic, environmental, and technology readiness factors in addition to physical properties of blendstocks that could be used to boost fuel economy can help spotlight those most likely to be viable in the near term.

40 CFR 600.207-86 - Calculation of fuel economy values for a model type.

Science.gov (United States)

2010-07-01

... calculation of the original base level fuel economy values), and (iii) All subconfigurations within the new... a new base level. The new base level is identical to the existing base level except that it shall be considered, for the purposes of this paragraph, as containing a new basic engine. The manufacturer will be...

40 CFR 600.207-93 - Calculation of fuel economy values for a model type.

Science.gov (United States)

2010-07-01

... calculation of the original base level fuel economy values); and (iii) All subconfigurations within the new... a new base level. The new base level is identical to the existing base level except that it shall be considered, for the purposes of this paragraph, as containing a new basic engine. The manufacturer will be...

Buses retrofitting with diesel particle filters: Real-world fuel economy and roadworthiness test considerations.

Science.gov (United States)

Fleischman, Rafael; Amiel, Ran; Czerwinski, Jan; Mayer, Andreas; Tartakovsky, Leonid

2018-05-01

Retrofitting older vehicles with diesel particulate filter (DPF) is a cost-effective measure to quickly and efficiently reduce particulate matter emissions. This study experimentally analyzes real-world performance of buses retrofitted with CRT DPFs. 18 in-use Euro III technology urban and intercity buses were investigated for a period of 12months. The influence of the DPF and of the vehicle natural aging on buses fuel economy are analyzed and discussed. While the effect of natural deterioration is about 1.2%-1.3%, DPF contribution to fuel economy penalty is found to be 0.6% to 1.8%, depending on the bus type. DPF filtration efficiency is analyzed throughout the study and found to be in average 96% in the size range of 23-560nm. Four different load and non-load engine operating modes are investigated on their appropriateness for roadworthiness tests. High idle is found to be the most suitable regime for PN diagnostics considering particle number filtration efficiency. Copyright © 2017. Published by Elsevier B.V.

Welfare implications of the renewable fuel standard with an integrated tax-subsidy policy

International Nuclear Information System (INIS)

Skolrud, Tristan D.; Galinato, Gregmar I.

2017-01-01

This paper derives the optimal integrated tax-subsidy policy where one input is taxed and revenues are used to subsidize the use of a substitute input to reduce greenhouse gas emissions given the existing policies under the Renewable Fuel Standard policies. We measure the welfare effects and impact on cellulosic ethanol production after implementing the tax-subsidy policy using a general equilibrium model. A revenue-neutral integrated tax-subsidy scheme leads to a small positive tax rate for crude oil and a large positive subsidy for cellulosic ethanol because the former has a larger emissions coefficient than the latter. The overall welfare effects of an integrated tax subsidy scheme are less than a 1% increase for the economy but the growth in the cellulosic ethanol industry could range from 28% to 238% because the revenues from taxing crude oil are directly used to subsidize cellulosic ethanol production. - Highlights: • We derive an integrated tax-subsidy interacting with the Renewable Fuel Standard. • The policy is revenue-neutral. • Policy results in a small crude oil tax and a large cellulosic ethanol subsidy. • Simulations indicate a welfare-increasing optimal policy. • Growth in the cellulosic ethanol industry ranges from 28% to 238%.

An inspection standard of fuel for the high temperature engineering test reactor

International Nuclear Information System (INIS)

Kobayashi, Fumiaki; Shiozawa, Shusaku; Sawa, Kazuhiro; Sato, Sadao; Hayashi, Kimio; Fukuda, Kosaku; Kaneko, Mitsunobu; Sato, Tsutomu.

1992-06-01

The High Temperature Engineering Test Reactor (HTTR) uses the fuel comprising coated fuel particles. A general inspection standard for the coated particle fuel, however, has not been established in Japan. Therefore, it has been necessary to prescribe the inspection standard of the fuel for HTTR. Under these circumstances, a fuel inspection standard of HTTR has been established under cooperation of fuel specialists both inside and outside of JAERI on referring to the inspection methods adopted in USA, Germany and Japan for HTGR fuels. Since a large number of coated fuel particle samples is needed to inspect the HTTR fuel, the sampling inspection standard has also been established considering the inspection efficiency. This report presents the inspection and the sampling standards together with an explanation of these standards. These standards will be applied to the HTTR fuel acceptance tests. (author)

77 FR 1319 - Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards

Science.gov (United States)

2012-01-09

... fuels such as ethanol and biodiesel. Potentially regulated categories include: NAICS \\1\\ Examples of... they are produced as well as the cost associated with transporting these fuels to the U.S. Of the... II.E, we believe that the 1.0 billion gallon standard can indeed be met. Since biodiesel has an...

76 FR 57105 - Greenhouse Gas Emissions Standards and Fuel Efficiency Standards for Medium- and Heavy-Duty...

Science.gov (United States)

2011-09-15

... CFR Parts 523, 534, and 535 Greenhouse Gas Emissions Standards and Fuel Efficiency Standards for...-2010-0079; FRL-9455-1] RIN 2060-AP61; 2127-AK74 Greenhouse Gas Emissions Standards and Fuel Efficiency... Heavy-Duty National Program that will reduce greenhouse gas emissions and fuel consumption for on-road...

An approach to meeting the spent fuel standard

Energy Technology Data Exchange (ETDEWEB)

Makhijani, A. [Institute for Energy and Environmental Research, Takoma Park, MD (United States)

1996-05-01

The idea of the spent fuel standard is that there should be a high surface gamma radiation to prevent theft. For purposes of preventing theft, containers should be massive, and the plutonium should be difficult to extract. This report discusses issues associated with the spent fuel standard.

An approach to meeting the spent fuel standard

International Nuclear Information System (INIS)

Makhijani, A.

1996-01-01

The idea of the spent fuel standard is that there should be a high surface gamma radiation to prevent theft. For purposes of preventing theft, containers should be massive, and the plutonium should be difficult to extract. This report discusses issues associated with the spent fuel standard

Climate consequences of low-carbon fuels: The United States Renewable Fuel Standard

International Nuclear Information System (INIS)

Hill, Jason; Tajibaeva, Liaila; Polasky, Stephen

2016-01-01

A common strategy for reducing greenhouse gas (GHG) emissions from energy use is to increase the supply of low-carbon alternatives. However, increasing supply tends to lower energy prices, which encourages additional fuel consumption. This “fuel market rebound effect” can undermine climate change mitigation strategies, even to the point where efforts to reduce GHG emissions by increasing the supply of low-carbon fuels may actually result in increased GHG emissions. Here, we explore how policies that encourage the production of low-carbon fuels may result in increased GHG emissions because the resulting increase in energy use overwhelms the benefits of reduced carbon intensity. We describe how climate change mitigation strategies should follow a simple rule: a low-carbon fuel with a carbon intensity of X% that of a fossil fuel must displace at least X% of that fossil fuel to reduce overall GHG emissions. We apply this rule to the United States Renewable Fuel Standard (RFS2). We show that absent consideration of the fuel market rebound effect, RFS2 appears to reduce GHG emissions, but once the fuel market rebound effect is factored in, RFS2 actually increases GHG emissions when all fuel GHG intensity targets are met. - Highlights: • Low-carbon fuels partially displace petroleum via fuel market rebound effect. • Synthesis of recent analyses shows incomplete petroleum displacement by biofuels. • Fuel market rebound effect can reduce or reverse climate benefit of low-carbon fuels. • Fossil fuel displacement must exceed relative carbon footprint of a low-carbon fuel. • The Renewable Fuel Standard increases greenhouse gas emissions when mandate is met.

40 CFR 600.510-12 - Calculation of average fuel economy and average carbon-related exhaust emissions.

Science.gov (United States)

2010-07-01

... and average carbon-related exhaust emissions. 600.510-12 Section 600.510-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF... Transportation. (iv) [Reserved] (2) Average carbon-related exhaust emissions will be calculated to the nearest...

Simulated Fuel Economy and Emissions Performance during City and Interstate Driving for a Heavy-Duty Hybrid Truck

Energy Technology Data Exchange (ETDEWEB)

Daw, C. Stuart; Gao, Zhiming; Smith, David E.; Laclair, Tim J.; Pihl, Josh A.; Edwards, K. Dean

2013-04-08

We compare simulated fuel economy and emissions for both conventional and hybrid class 8 heavy-duty diesel trucks operating over multiple urban and highway driving cycles. Both light and heavy freight loads were considered, and all simulations included full aftertreatment for NOx and particulate emissions controls. The aftertreatment components included a diesel oxidation catalyst (DOC), urea-selective catalytic NOx reduction (SCR), and a catalyzed diesel particulate filter (DPF). Our simulated hybrid powertrain was configured with a pre-transmission parallel drive, with a single electric motor between the clutch and gearbox. A conventional HD truck with equivalent diesel engine and aftertreatment was also simulated for comparison. Our results indicate that hybridization can significantly increase HD fuel economy and improve emissions control in city driving. However, there is less potential hybridization benefit for HD highway driving. A major factor behind the reduced hybridization benefit for highway driving is that there are fewer opportunities to utilize regenerative breaking. Our aftertreatment simulations indicate that opportunities for passive DPF regeneration are much greater for both hybrid and conventional trucks during highway driving due to higher sustained exhaust temperatures. When passive DPF regeneration is extensively utilized, the fuel penalty for particulate control is virtually eliminated, except for the 0.4%-0.9% fuel penalty associated with the slightly higher exhaust backpressure.

Experimental study on fuel economies and emissions of direct-injection premixed combustion engine fueled with gasoline/diesel blends

International Nuclear Information System (INIS)

Du, Jiakun; Sun, Wanchen; Guo, Liang; Xiao, Senlin; Tan, Manzhi; Li, Guoliang; Fan, Luyan

2015-01-01

Highlights: • A compound combustion concept was proposed and investigated. • Premixed combustion near the top dead center was investigated using blended fuels. • Increasing gasoline blend ratio was found to enhance the mixture preparation. • Too much addition of gasoline decreases indicated thermal efficiency. • Gasoline/diesel blends may be a promising alternative for premixed combustion. - Abstract: The effects of gasoline/diesel blended fuel composed of diesel fuel with gasoline as additives in volume basis, on combustion, fuel economies and exhaust emissions were experimentally investigated. Tests were carried out based on a turbocharged Common-rail Direct Injection engine at a constant engine speed of 1800 r/min and different loads of 3.2 bar, 5.1 bar Indicated Mean Effective Pressure. Additionally, the effect of combustion phasing and Exhaust Gas Recirculation were evaluated experimentally for various fuels. The results indicated that with the fraction of gasoline increasing in blends, the ignition delay was prolonged and the combustion phasing was retarded with the common injection timing. This led to a significant increase of premixed burning phase, which was in favor of smoke reduction; although, too much gasoline might be adverse to fuel consumption. An optimum combustion phasing was identified, leading to a higher thermal efficiency and better premixed combustion with blended fuels. A combined application of Exhaust Gas Recirculation and blended fuel with a high gasoline fraction was confirmed effective in reducing the oxides of nitrogen and smoke emissions simultaneously at the optimum combustion phasing without giving significant penalty of fuel consumption. A compound combustion mode with its emission lower than the conventional Compression Ignition engines, and efficiency higher than the typical Spark Ignition engines, could be achieved with a cooperative control of Exhaust Gas Recirculation and combustion phasing of the gasoline

Passenger car fuel consumption survey

Energy Technology Data Exchange (ETDEWEB)

1984-03-01

This survey originated from a proposal to monitor the fuel consumption and fuel economy of personal use passenger cars operated in Canada. Its purpose is to establish a data base which would contain information on total distance travelled, total amount of fuel consumed, average distance obtained per unit of fuel, total expenditures on fuel, and seasonal fluctuations in fuel consumption and in distance travelled. Among the needs served by this data base are the monitoring of passenger car fuel economy standards and the estimation of pasenger car fuel requirements in conditions involving fuel shortages. Survey methodology is by telephone interview to trace selected vehicles to the registered owners, at which time a fuel purchase diary is then mailed to the principal driver of the car. The results are tabulated on a quarterly basis and to be released as they become available in bulletins similar to this. Data are presented for each province and the total for Canada is given. During the fourth quarter of 1982, it is estimated that there were 7.3 million personal use passenger cars operated in Canada. These cars were driven 28 billion kilometers and consumed 4.3 billion litres of fuel. Their average litres/100 kilometres and the average fuel consumption was 590 litres. 8 tabs.

A comparison of high-speed flywheels, batteries, and ultracapacitors on the bases of cost and fuel economy as the energy storage system in a fuel cell based hybrid electric vehicle

Energy Technology Data Exchange (ETDEWEB)

Doucette, Reed T.; McCulloch, Malcolm D. [Department of Engineering Science, University of Oxford, Thom Building, Parks Road, Oxford, OX1 3PJ (United Kingdom)

2011-02-01

Fuel cells aboard hybrid electric vehicles (HEVs) are often hybridized with an energy storage system (ESS). Batteries and ultracapacitors are the most common technologies used in ESSs aboard HEVs. High-speed flywheels are an emerging technology with traits that have the potential to make them competitive with more established battery and ultracapacitor technologies in certain vehicular applications. This study compares high-speed flywheels, ultracapacitors, and batteries functioning as the ESS in a fuel cell based HEV on the bases of cost and fuel economy. In this study, computer models were built to simulate the powertrain of a fuel cell based HEV where high-speed flywheels, batteries, and ultracapacitors of a range of sizes were used as the ESS. A simulated vehicle with a powertrain using each of these technologies was run over two different drive cycles in order to see how the different ESSs performed under different driving patterns. The results showed that when cost and fuel economy were both considered, high-speed flywheels were competitive with batteries and ultracapacitors. (author)

Comparative evaluation of fuel temperature coefficient of standard and CANFLEX fuels in CANDU 6

International Nuclear Information System (INIS)

Kim, Woosong; Hartant, Donny; Kim, Yonghee

2012-01-01

The fuel temperature reactivity coefficient (FTC) of CANDU 6 has become a concerning issue. The FTC was found to be slightly positive for the operating condition of CANDU 6. Since CANDU 6 has unique fuel arrangement and very soft neutron spectrum, its Doppler reactivity feedback of U 238 is rather weak. The upscattering by oxygen in fuel and Pu 239 buildup with fuel depletion are responsible for the positive FTC value at high temperature. In this study, FTC of both standard CANDU and CANFLEX fuel lattice are re evaluated. A Monte Carlo code Serpent2 was chosen as the analysis tool because of its high calculational speed and it can account for the thermal motion of heavy nuclides in fuel by using the Doppler Broadening Rejection Correction (DBRC) method. It was reported that the fuel Doppler effect is noticeably enhanced by accounting the target thermal motion. Recently, it was found that the FTC of the CANDU 6 standard fuel is noticeably enhanced by the DBRC

METHODS TO MEASURE, PREDICT AND RELATE FRICTION, WEAR AND FUEL ECONOMY

Energy Technology Data Exchange (ETDEWEB)

Gravante, Steve [Ricardo, Inc.; Fenske, George [Argonne National Lab. (ANL), Argonne, IL (United States); Demas, Nicholas [Argonne National Lab. (ANL), Argonne, IL (United States); Erck, Robert [Argonne National Lab. (ANL), Argonne, IL (United States)

2018-03-19

High-fidelity measurements of the coefficient of friction and the parasitic friction power of the power cylinder components have been made for the Isuzu 5.2L 4H on-highway engine. In particular, measurements of the asperity friction coefficient were made with test coupons using Argonne National Lab’s (ANL) reciprocating test rig for the ring-on-liner and skirt-on-liner component pairs. These measurements correlated well with independent measurements made by Electro-Mechanical Associates (EMA). In addition, surface roughness measurements of the Isuzu components were made using white light interferometer (WLI). The asperity friction and surface characterization are key inputs to advanced CAE simulation tools such as RINGPAK and PISDYN which are used to predict the friction power and wear rates of power cylinder components. Finally, motored friction tests were successfully performed to quantify the friction mean effective pressure (FMEP) of the power cylinder components for various oils (High viscosity 15W40, low viscosity 5W20 with friction modifier (FM) and specially blended oil containing consisting of PAO/ZDDP/MoDTC) at 25, 50, and 110 °C. Ricardo's objective is to use this data along with advanced CAE methods to develop empirical characterizations of friction and wear mechanisms in internal combustion engines such that the impact of such mechanisms of engine fuel consumption and/or vehicle fuel economy can be estimated. The value of such predictive schemes is that if one knows how a particular friction reduction technology changes oil viscosity and/or the friction coefficient then the fuel consumption or fuel economy impacts can be estimated without the excessive cost of motored or fired engine tests by utilizing cost effective lab scale tests and in combination with advanced analytical methods. One accomplishment made during this work was the development and validation of a novel technique for quantifying wear using data from WLI through the use of

Fuel carbon intensity standards may not mitigate climate change

International Nuclear Information System (INIS)

Plevin, Richard J.; Delucchi, Mark A.; O’Hare, Michael

2017-01-01

To mitigate the climate change effects of transportation, the US states of California and Oregon, the Canadian province of British Columbia, and the European Union have implemented regulations to reduce the life cycle greenhouse gas (GHG) emissions intensity of transport fuel, commonly referred to as 'carbon intensity', or CI. In this article, we unpack the theory and practice of fuel CI standards, examining claims regarding climate-change mitigation. We show that these standards do not reliably mitigate climate change because estimates of GHG reductions rely primarily on models that are not designed to estimate changes in emissions and climate impacts. Some regulations incorporate models that estimate a subset of changes in emissions, but the models must project changes in global markets over decades, and there is little agreement about the best model structure or parameter values. Since multiple models and projections may be equally plausible, fuel CI is inevitably subjective and unverifiable. We conclude that regulating or taxing observable emissions would more reliably achieve emission reduction. - Highlights: • Use of fuel carbon intensity (CI) standards has been expanding recently. • Fuel CI ratings are subjective, scenario- and model-dependent. • Uncertainty in fuel CI ratings creates uncertainty in policy outcomes. • There is no reliable test of whether fuel CI standards mitigate climate change. • Regulating or taxing observable emissions would be a more reliable approach.

77 FR 51499 - Greenhouse Gas Emissions Standards and Fuel Efficiency Standards for Medium- and Heavy-Duty...

Science.gov (United States)

2012-08-24

... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 49 CFR Part 535 [NHTSA 2012-0126] RIN 2127-AK74 Greenhouse Gas Emissions Standards and Fuel Efficiency Standards for Medium... purpose of reducing greenhouse gas (GHG) emissions because the GHG standards fundamentally regulate fuel...

Patent challenges for standard-setting in the global economy : lessons from information and communication industry

NARCIS (Netherlands)

Maskus, K.; Merrill, S.A.; Bekkers, R.N.A.; Sandy Block, Marc; Contreras, Jorge; Gilbert, Richard; Goodman, David; Marasco, Amy; Simcoe, Tim; Smoot, Oliver; Suttmeier, Richard; Updegrove, Andrew

2014-01-01

Patent Challenges for Standard-Setting in the Global Economy: Lessons from Information and Communication Technology examines how leading national and multinational standard-setting organizations (SSOs) address patent disclosures, licensing terms, transfers of patent ownership, and other issues that

The National Center For Hydrogen And Fuel Cells. Jump-starting the hydrogen economy through research

International Nuclear Information System (INIS)

Stefanescu, Ioan; Varlam, Mihai; Carcadea, Elena

2010-01-01

Full text: The research, design and implementation of hydrogen-based economy must consider each of the segments of the hydrogen energy system - production, supply, storage, conversion. The National Center for Hydrogen and Fuel Cells has the experience, expertise, facilities and instrumentation necessary to have a key role in developing any aspect of hydrogen-based economy, aiming to integrate technologies for producing and using hydrogen as an 'energy vector'. This paper presents a simulation of the applied 'learning curve' concept, NCHFC being the key element of R and D in the field in comparing the costs involved. It also presents the short and medium term research program of NCHFC, the main research and development directions being specified. (authors)

Potential role of nuclear power in developing and transition economies

International Nuclear Information System (INIS)

Ganiage, D.; Dierstein, P.

1995-01-01

The potential role of nuclear power is different in developing or in transition economies; in developing countries such as China, the growth of electricity consumption is high and the construction of several standardized plants is economically justified; in transitional economies, such as Ukraine, the needs are uncertain, old and unsafe plants have to be decommissioned and uncompleted nuclear plants (due to financial problems) should be completed. Nuclear power may provide the developing and transition economies with several advantages such as energy independence and fuel supply security, minimal environmental pollution, support to local industry and employment. It also means the support of national authorities and the development of a suitable infrastructure for plant safety and waste management, financial help and local population acceptance

The Effect of Intellectual Property Standards on the Catch-Up Process Of Emerging Market Economies

DEFF Research Database (Denmark)

Darendeli, Izzet; Brandl, Kristin Martina; Hamilton, III, Robert D.

2014-01-01

The catch-up process of emerging market economies is dependent on multiple factors, such as local governmental regulations but also global industry developments. We investigate how intellectual property (IP) protection standards affect this catch-up process. The alignment of these standards...

Improving of diesel combustion-pollution-fuel economy and performance by gasoline fumigation

International Nuclear Information System (INIS)

Şahin, Zehra; Durgun, Orhan

2013-01-01

Highlights: • The effects of gasoline fumigation on the engine performance and NO x emission were investigated in Ford XLD 418 T automotive diesel engine. • Gasoline at approximately (2, 4, 6, 8 10, and 12)% (by vol.) ratios was injected into intake air by a carburetor. • GF enhances effective power and reduces brake specific fuel consumption, cost, and NO x emission. - Abstract: One of the most important objectives of the studies worldwide is to improve combustion of diesel engine to meet growing energy needs and to reduce increasing environmental pollution. To accomplish this goal, especially to reduce pollutant emissions, researchers have focused their interest on the field of alternative fuels and alternative solutions. Gasoline fumigation (GF) is one of these alternative solutions, by which diesel combustion, fuel economy, and engine performance are improved, and environmental pollution is decreased. In the fumigation method, gasoline is injected into intake air, either by a carburetor, which main nozzle section is adjustable or by a simple injection system. In the present experimental study, a simple carburetor was used, and the effects of gasoline fumigation at (2, 4, 6, 8, 10, 12)% (by vol.) gasoline ratios on the combustion, NO x emission, fuel economy, and engine performance sophisticatedly investigated for a fully instrumented, four-cylinder, water-cooled indirect injection (IDI), Ford XLD 418 T automotive diesel engine. Tests were conducted for each of the above gasoline fumigation ratios at three different speeds and for (1/1, 3/4, and 1/2) fuel delivery ratios (FDRs). GF test results showed that NO x emission is lower than that of neat diesel fuel (NDF). NO x emission decreases approximately 4.20%, 2.50%, and 9.65% for (1/1, 3/4, and 1/2) FDRs, respectively. Effective power increases approximately 2.38% for 1/1 FDR. At (2500 and 3000) rpms, effective power decreases at low gasoline ratios, but it increases at high gasoline ratios for 3/4 and 1

THE INFLUENCE OF CORRUPTION ON CORPORATE GOVERNANCE STANDARDS: SHARED CHARACTERISTICS OF RAPIDLY DEVELOPING ECONOMIES

Directory of Open Access Journals (Sweden)

Michelle I. Caron

2012-01-01

Full Text Available This article evaluates the relationship between the level of corruption in rapidly developing economies and corporate governance processes therein.  Previous literature illustrates a strong relationship between corporate governance and corruption and suggests that in countries with high levels of corruption, firms lack efficient corporate governance practices.  Similarly, countries with deficient corporate governance practices and low levels of compliance to these standards breed corruption leading to a wide range of transparency dilemmas.  This study delves deeper through careful examination regarding the level of compliance with corporate governance standards and the pervasive effects of corruption on the governance processes of firms with specific regard to rapidly developing economies as well as offering comparisons and similarities of shared characteristics among these countries.

Fuel Cell Development for NASA's Human Exploration Program: Benchmarking with "The Hydrogen Economy"

Science.gov (United States)

Scott, John H.

2007-01-01

The theoretically high efficiency and low temperature operation of hydrogen-oxygen fuel cells has motivated them to be the subject of much study since their invention in the 19th Century, but their relatively high life cycle costs kept them as a "solution in search of a problem" for many years. The first problem for which fuel cells presented a truly cost effective solution was that of providing a power source for NASA's human spaceflight vehicles in the 1960 s. NASA thus invested, and continues to invest, in the development of fuel cell power plants for this application. This development program continues to place its highest priorities on requirements for minimum system mass and maximum durability and reliability. These priorities drive fuel cell power plant design decisions at all levels, even that of catalyst support. However, since the mid-1990's, prospective environmental regulations have driven increased governmental and industrial interest in "green power" and the "Hydrogen Economy." This has in turn stimulated greatly increased investment in fuel cell development for a variety of commercial applications. This investment is bringing about notable advances in fuel cell technology, but, as these development efforts place their highest priority on requirements for minimum life cycle cost and field safety, these advances are yielding design solutions quite different at almost every level from those needed for spacecraft applications. This environment thus presents both opportunities and challenges for NASA's Human Exploration Program

Fuel Economy Improvement of a Heavy-Duty Powertrain by Using Hardware-in-Loop Simulation and Calibration

Directory of Open Access Journals (Sweden)

Bolan Liu

2015-09-01

Full Text Available Fuel economy efficiency is one of the most important parameters for vehicle powertrains, which is of particular interest for heavy-duty powertrain calibration. Conventionally, this work relies heavily on road tests, which cost more and may lead to long duration product development cycles. The paper proposes a novel hardware-in-loop modeling and calibration method to work it out. A dSPACE hardware-based test bench was successfully established and validated, which is valuable for a more efficient and easier shift schedule in calibration. Meanwhile, a real-time dynamic powertrain model, including a diesel engine, torque converter, gear box and driver model was built. Typical driving cycles that both velocity and slope information were constructed for different road conditions. A basic economic shift schedule was initially calculated and then optimal calibrated by the test bench. The results show that there is an optimal relationship between an economic shift schedule and speed regulation. By matching the best economic shift schedule regulation to different road conditions; the fuel economy of vehicles can be improved. In a smooth driving cycle; when the powertrain applies a larger speed regulation such as 12% and the corresponding shift schedule; the fuel consumption is smaller and is reduced by 13%. In a complex driving cycle, when the powertrain applies a smaller speed regulation such as 5% along with the corresponding shift schedule; the fuel consumption is smaller and is reduced by 5%. The method thus can provide guidance for economic calibration experiments of off-road heavy-duty vehicles.

Voluntary Truck and Bus Fuel-Economy-Program marketing plan. Final technical report, September 29, 1980-January 29, 1982

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

The aim of the program is to improve the utilization of fuel by commercial trucks and buses by updating and implementing specific approaches for educating and monitoring the trucking industry on methods and means of conserving fuels. The following outlines the marketing plan projects: increase use of program logo by voluntary program members and others; solicit trade publication membership and support; brief Congressional delegations on fuel conservation efforts; increase voluntary program presence before trade groups; increase voluntary program presence at truck and trade shows; create a voluntary program display for use at trade shows and in other areas; review voluntary program graphics; increase voluntary program membership; and produce placemats carrying fuel conservation messages; produce a special edition of Fuel Economy News, emphasizing the driver's involvement in fuel conservation; produce posters carrying voluntary program fuel conservation message. Project objectives, activities, and results for each project are summarized.

ANALYSIS OF THE IMPLEMENTATION OF INTERNATIONAL FINANCIAL REPORTING STANDARDS BY COUNTRIES WITH ECONOMIES IN TRANSITION

Directory of Open Access Journals (Sweden)

B. Zasadnyi

2013-08-01

Full Text Available The article deals with experience of application of international financial reporting standards in different countries with economies in transition. The main advantages and disadvantages of the implementation of international financial reporting standards for financial reporting for Ukrainian companies are based on this experience.

Substantial improvements of fuel economy. Potentials of electric and hybrid electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Joergensen, K [Technical Univ. of Denmark (Denmark); Nielsen, L H [Forskningscenter Risoe (Denmark)

1996-12-01

This paper evaluates the scope for improvement of the energy and environmental impacts of road traffic by means of electrical and hybrid electric propulsion. These technologies promise considerable improvements of the fuel economy of vehicles compared to the present vehicle types as well as beneficial effects for the energy and traffic system. The paper - based on work carried out in the project `Transportation fuel based on renewable energy`, funded by the National Energy Agency of Denmark and carried out by Department of Buildings and Energy, Technical University of Denmark and System Analysis Department, Risoe National Laboratory - assesses the potentials for reduction of the primary energy consumption and emissions, and points to the necessary technical development to reap these benefits. A case study concerning passenger cars is analysed by means of computer simulations, comparing electric and hybrid electric passenger car to an equivalent reference vehicle (a conventional gasoline passenger car). (au) 10 refs.

Consumer Views: Fuel Economy, Plug-in Electric Vehicle Battery Range, and Willingness to Pay for Vehicle Technology

Energy Technology Data Exchange (ETDEWEB)

Singer, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-05-11

This presentation includes data captured by the National Renewable Energy Laboratory (NREL) to support the U.S. Department of Energy's Vehicle Technologies Office (VTO) research efforts. The data capture consumer views on fuel economy, plug-in electric vehicle battery range, and willingness to pay for advanced vehicle technologies.

Economy and the fuel market

International Nuclear Information System (INIS)

1994-01-01

The nuclear fuel manufacturing constitutes a considerable venture for the competitiveness of the nuclear power sector although it represents a relatively modest fraction (around 4%) of the nuclear kWh cost. The COGEMA group is participating through its branches in the control of the most part (32%) of the world manufacturing capacity of fuel for PWR. Amounting up to 242 operating installations this reactor type is the most widespread in the world. The paper discusses the costs, the fuel clients and the fuel suppliers. Data concerning the boiling water and fast neutron reactors, geographical localization of the PWR and VVER reactors all over the world, the PWR and fuel for PWR manufacturers are also presented

How Improved Fuel Efficiency May Change U.S. Middle East Policy

Science.gov (United States)

2012-03-14

corporations through diplomatic channels to reduce risks and permit U.S. companies to operate under foreign laws and customs . The federal government should...insufficient Corporate Average Fuel Economy ( CAFE ) standards are two reasons for unchecked demand and the inability to wean the transportation...and development into alternative fuels. Over the past 32 years Congress raised the CAFE standard only 6.9 miles per gallon (mpg), from 17.2 to 24.1

Cost and Fuel Efficient SCR-only Solution for post-2010 HD Emission Standards

NARCIS (Netherlands)

Cloudt, R.P.M.; Willems, F.P.T.; Heijden, van der P.

2009-01-01

A promising SCR-only solution is presented to meetpost-2010 NOx emission targets for heavy dutyapplications. The proposed concept is based on anengine from a EURO IV SCR application, which isconsidered optimal with respect to fuel economy andcosts. The addition of advanced SCR after

The Impact of Analog and Bang-Bang Steering Gear Control on Ship's Fuel Economy

DEFF Research Database (Denmark)

Nørtoft Thomsen, J. C.; Blanke, Mogens; Reid, R. E.

1982-01-01

it is found to be at least equally important regarding steering performance and fuel economy. The paper presents a comprehensive survey of steering gear principles commonly used, including relevant details of three analog steering gear servo principles, which have outperformed conventional designs. Control......The latest years have shown considerable efforts towards improving steering generated propulsion losses of ships by the introduction of various sophisticated control algorithms in the autopilots. However, little previous attention has been given to the steering gear control loop, although...

Rocker shoe, minimalist shoe, and standard running shoe : A comparison of running economy

NARCIS (Netherlands)

Sobhani, Sobhan; Bredeweg, Steven; Dekker, Rienk; Kluitenberg, Bas; van den Heuvel, Edwin; Hijmans, Juha; Postema, Klaas

Objectives: Running with rocker shoes is believed to prevent lower limb injuries. However, it is not clear how running in these shoes affects the energy expenditure. The purpose of this study was, therefore, to assess the effects of rocker shoes on running economy in comparison with standard and

API focuses on cleanliness, economics of fossil fuels

International Nuclear Information System (INIS)

Anon.

1993-01-01

Fossil fuels, consumed in free markets, are playing positive economic and environmental roles as the world economy becomes integrated, industry leader said last week. Environmental zealots threaten to force conversion from gasoline as a motor fuel in the U.S. and oppose the growing integration of the world economy. Fossil fuels, free markets, human creativity, and entrepreneurial spirit--not government intervention--are the keys to a clean environment, said API pres. Charles J. DiBona and outgoing Chairman C.J. (Pete) Silas, chairman and chief executive officer of Phillips Petroleum Co. DiBona said proponents of the BTU tax defeated earlier this year used erroneous assumptions to make a case against oil use in an effort to replace the efficiency of the marketplace with the inefficiency of bureaucracy. The government's role is to set tough standards and avoid dictating the way environmental standards are met, they said. Other speakers warned that voluntary measures put forward by the Clinton administration of address global climate change issues likely will fall short

14 CFR 34.11 - Standard for fuel venting emissions.

Science.gov (United States)

2010-01-01

... Emissions (New and In-Use Aircraft Gas Turbine Engines) § 34.11 Standard for fuel venting emissions. (a) No fuel venting emissions shall be discharged into the atmosphere from any new or in-use aircraft gas... include one of the following: (1) Incorporation of an FAA-approved system that recirculates the fuel back...

Environmental monitoring standardization of effluent from nuclear fuel cycle facilities in China

International Nuclear Information System (INIS)

Gao Mili

1993-01-01

China has established some environmental monitoring standards of effluent from nuclear fuel cycle facilities. Up to date 33 standards have been issued; 10 to be issued; 11 in drafting. These standards cover sampling, gross activities measurement, analytical methods and management rules and so on. They involve with almost all nuclear fuel cycle facilities and have formed a complete standards system. By the end of the century, we attempt to draft a series of analytical and determination standards in various environmental various medium, they include 36 radionuclides from nuclear fuel cycle facilities. (3 tabs.)

77 FR 71163 - Federal Motor Vehicle Safety Standards; Windshield Zone Intrusion

Science.gov (United States)

2012-11-29

... fully determined. Those influences are more stringent U.S. Corporate Average Fuel Economy (CAFE... materials to meet CAFE standards, including materials in and around the hoods of vehicles. Hood design could... evolves in response to CAFE standards. Additionally, in November 2008, the World Forum for Harmonization...

Substitutability of Electricity and Renewable Materials for Fossil Fuels in a Post-Carbon Economy

Directory of Open Access Journals (Sweden)

Antonio García-Olivares

2015-11-01

Full Text Available A feasible way to avoid the risk of energy decline and combat climate change is to build a 100% renewable global energy mix. However, a globally electrified economy cannot grow much above 12 electric terawatts without putting pressure on the limits of finite mineral reserves. Here we analyze whether 12 TW of electricity and 1 TW of biomass (final power will be able to fuel a future post-carbon economy that can provide similar services to those of a contemporary economy. Contrarily to some pessimistic expectations, this analysis shows that the principle economic processes can be replaced with sustainable alternatives based on electricity, charcoal, biogas and hydrogen. Furthermore, those services that cannot be replaced are not as crucial so as to cause a return to a pre-industrial society. Even so, land transport and aviation are at the limit of what is sustainable, outdoor work should be reorganized, metal primary production should be based on hydrogen reduction when possible, mineral production should be increasingly based on recycling, the petrochemical industry should shrink to a size of 40%–43% of the 2012 petrochemical sector, i.e., a size similar to that the sector had in 1985–1986, and agriculture may require organic farming methods to be sustainable.

Assessment of technologies to meet a low carbon fuel standard.

Science.gov (United States)

Yeh, Sonia; Lutsey, Nicholas P; Parker, Nathan C

2009-09-15

California's low carbon fuel standard (LCFS) was designed to incentivize a diverse array of available strategies for reducing transportation greenhouse gas (GHG) emissions. It provides strong incentives for fuels with lower GHG emissions, while explicitly requiring a 10% reduction in California's transportation fuel GHG intensity by 2020. This paper investigates the potential for cost-effective GHG reductions from electrification and expanded use of biofuels. The analysis indicates that fuel providers could meetthe standard using a portfolio approach that employs both biofuels and electricity, which would reduce the risks and uncertainties associated with the progress of cellulosic and battery technologies, feedstock prices, land availability, and the sustainability of the various compliance approaches. Our analysis is based on the details of California's development of an LCFS; however, this research approach could be generalizable to a national U.S. standard and to similar programs in Europe and Canada.

Forest fuel - economy and models for cost analysis

International Nuclear Information System (INIS)

Olsson, Anders.

1991-01-01

The purpose of this report is to develop guidelines for the R and D work within Skogskraft with the aim of improving the efficiency of the investigatory work. The report mainly concerns logging waste. The contents are as follows; Terminology - definitions: This section includes a brief description of wood fuels with regard to terminology, definitions, production and marketing. Units of measurement: Different units of measurement are descrived and their relationship to forestry, sawmills and consumers of wood fuels. An account is also given of effective thermal values and formulas for calculations of the energy content for different wood fuels. Calculation models, analyses: This section discusses different models and standards for calculating machine and manual costs. In addition, views are given on cost analysis and certain guidelines with regard to overhead costs. Actors and systems: There is a risk that technical problems receive a far too dominant role in relation to problems which concern organisation and structure. Consequently, it is important to define the actors and to illustrate the different driving forces and tensions that may occur. Seven different actors/interested parties have been described and analysed with regard to primary and secondary interests in ecological, technical and economic questions. Preparation of reports: Certain recommendations have been given with regard to formal requirements and quality requirements

Cost and fuel efficient SCR-only solution for post-2010 HD emission standards

NARCIS (Netherlands)

Cloudt, R.P.M.; Willems, F.P.T.; Heijden, P.V.A.M. van der

2009-01-01

A promising SCR-only solution is presented to meet post-2010 NOx emission targets for heavy duty applications. The proposed concept is based on an engine from a EURO IV SCR application, which is considered optimal with respect to fuel economy and costs. The addition of advanced SCR after treatment

Alternative Fuels Data Center: Codes and Standards Resources

Science.gov (United States)

resources linked below help project developers and code officials prepare and review code-compliant projects , storage, and infrastructure. The following charts show the SDOs responsible for these alternative fuel codes and standards. Biodiesel Vehicle and Infrastructure Codes and Standards Chart Electric Vehicle and

Lean Gasoline System Development for Fuel Efficient Small Cars

Energy Technology Data Exchange (ETDEWEB)

Smith, Stuart R. [General Motors LLC, Pontiac, MI (United States)

2013-11-25

The General Motors and DOE cooperative agreement program DE-EE0003379 is completed. The program has integrated and demonstrated a lean-stratified gasoline engine, a lean aftertreatment system, a 12V Stop/Start system and an Active Thermal Management system along with the necessary controls that significantly improves fuel efficiency for small cars. The fuel economy objective of an increase of 25% over a 2010 Chevrolet Malibu and the emission objective of EPA T2B2 compliance have been accomplished. A brief review of the program, summarized from the narrative is: The program accelerates development and synergistic integration of four cost competitive technologies to improve fuel economy of a light-duty vehicle by at least 25% while meeting Tier 2 Bin 2 emissions standards. These technologies can be broadly implemented across the U.S. light-duty vehicle product line between 2015 and 2025 and are compatible with future and renewable biofuels. The technologies in this program are: lean combustion, innovative passive selective catalyst reduction lean aftertreatment, 12V stop/start and active thermal management. The technologies will be calibrated in a 2010 Chevrolet Malibu mid-size sedan for final fuel economy demonstration.

Hydrogen economy

Energy Technology Data Exchange (ETDEWEB)

Pahwa, P.K.; Pahwa, Gulshan Kumar

2013-10-01

In the future, our energy systems will need to be renewable and sustainable, efficient and cost-effective, convenient and safe. Hydrogen has been proposed as the perfect fuel for this future energy system. The availability of a reliable and cost-effective supply, safe and efficient storage, and convenient end use of hydrogen will be essential for a transition to a hydrogen economy. Research is being conducted throughout the world for the development of safe, cost-effective hydrogen production, storage, and end-use technologies that support and foster this transition. This book discusses hydrogen economy vis-a-vis sustainable development. It examines the link between development and energy, prospects of sustainable development, significance of hydrogen energy economy, and provides an authoritative and up-to-date scientific account of hydrogen generation, storage, transportation, and safety.

40 CFR 600.208-08 - Calculation of FTP-based and HFET-based fuel economy values for a model type.

Science.gov (United States)

2010-07-01

... the original base level fuel economy values); and (iii) All subconfigurations within the new base... separating subconfigurations from an existing base level and placing them into a new base level. The new base... this paragraph, as containing a new basic engine. The manufacturer will be permitted to designate such...

The Development of Fuel Cell Technology for Electric Power Generation - From Spacecraft Applications to the Hydrogen Economy

Science.gov (United States)

Scott, John H.

2005-01-01

The fuel cell uses a catalyzed reaction between a fuel and an oxidizer to directly produce electricity. Its high theoretical efficiency and low temperature operation made it a subject of much study upon its invention ca. 1900, but its relatively high life cycle costs kept it as "solution in search of a problem" for its first half century. The first problem for which fuel cells presented a cost effective solution was, starting in the 1960's that of a power source for NASA's manned spacecraft. NASA thus invested, and continues to invest, in the development of fuel cell power plants for this application. However, starting in the mid-1990's, prospective environmental regulations have driven increased governmental and industrial interest in "green power" and the "Hydrogen Economy." This has in turn stimulated greatly increased investment in fuel cell development for a variety of terrestrial applications. This investment is bringing about notable advances in fuel cell technology, but these advances are often in directions quite different from those needed for NASA spacecraft applications. This environment thus presents both opportunities and challenges for NASA's manned space program.

Standardization of Alternative Fuels. Phase 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-08-15

March 2003 the Executive Committee of the International Energy Agency's Implementing Agreement on Advanced Motor fuels (IEA/AMF) decided to continue annex XXVII 'Standardization of alternative fuels' with a second phase. The purpose of the second phase was to go further in the contacts with the International Organization for Standardization (ISO) as well as the European Committee for Standardization (CEN) and their technical committees, to better understand their needs and to investigate how IEA/AMF could contribute to their work. It was also scheduled to put forward proposals on how IEA/AMF could cooperate with CEN and ISO and their technical committees (TC: s), primarily ISO/TC 28 'Petroleum Products and Lubricants' and CEN/TC 19 'Petroleum Products, Lubricants and Related Products'. The main part of the work in IEA/AMF annex XXVII phase two has focused on personal contacts within CEN/TC 19 and ISO/TC 28, but also on data and information collection from websites and written information. Together with the analysis of this information, the internal organization of a cooperation between IEA/AMF and ISO/TC 28 and of a cooperation between IEA/AMF and CEN/TC 19 have also been discussed and analysed.

Safety standards, legislation and codes of practice for fuel cell manufacture and operation

Energy Technology Data Exchange (ETDEWEB)

Wilcox, C.P.

1999-07-01

This report examines safety standards, legislation and codes of practice for fuel cell manufacture and operation in the UK, Europe and internationally. Management of health and safety in the UK is discussed, and the characteristics of phosphoric acid (PAFC), proton exchange membrane (PEM), molten carbonate (MCFC), solid oxide (SOFC) fuel cells are described. Fuel cell power plant standards and manufacture in the UK, design and operational considerations, end of life disposal, automotive fuel cell system, and fuelling and vehicular concerns are explored, and standards, legislation and codes of practice are explained in the appendix.

Search for adequate quality standards for neutron radiography of nuclear fuel

International Nuclear Information System (INIS)

Domanus, J.C.

1983-01-01

Unlike in other fields of industrial radiography, where standard methods and procedures are used to control the quality of the radiographic image, no such standard exists for neutron radiography of nuclear fuel. To fill that gap it was felt that standardization work ought to be started in that field, too. Accordingly in 1979 an Euratom Neutron Radiography Working Group was constituted, which initiated standardization work in the field of neutron radiography of nuclear fuel. Finding adequate standards for image quality of neutron radiographs and checking the accuracy of dimension measurements from them were given first priority. (Auth.)

Motor Fuel Excise Taxes

Energy Technology Data Exchange (ETDEWEB)

2015-09-01

A new report from the National Renewable Energy Laboratory (NREL) explores the role of alternative fuels and energy efficient vehicles in motor fuel taxes. Throughout the United States, it is common practice for federal, state, and local governments to tax motor fuels on a per gallon basis to fund construction and maintenance of our transportation infrastructure. In recent years, however, expenses have outpaced revenues creating substantial funding shortfalls that have required supplemental funding sources. While rising infrastructure costs and the decreasing purchasing power of the gas tax are significant factors contributing to the shortfall, the increased use of alternative fuels and more stringent fuel economy standards are also exacerbating revenue shortfalls. The current dynamic places vehicle efficiency and petroleum use reduction polices at direct odds with policies promoting robust transportation infrastructure. Understanding the energy, transportation, and environmental tradeoffs of motor fuel tax policies can be complicated, but recent experiences at the state level are helping policymakers align their energy and environmental priorities with highway funding requirements.

Fusion power economy of scale

International Nuclear Information System (INIS)

Dolan, T.J.

1993-01-01

In the next 50 yr, the world will need to develop hundreds of gigawatts of non-fossil-fuel energy sources for production of electricity and fuels. Nuclear fusion can probably provide much of the required energy economically, if large single-unit power plants are acceptable. Large power plants are more common than most people realize: There are already many multiple-unit power plants producing 2 to 5 GW(electric) at a single site. The cost of electricity (COE) from fusion energy is predicted to scale as COE ∼ COE 0 (P/P 0 ) -n , where P is the electrical power, the subscript zero denotes reference values, and the exponent n ∼ 0.36 to 0.7 in various designs. The validity ranges of these scalings are limited and need to be extended by future work. The fusion power economy of scale derives from four interrelated effects: improved operations and maintenance costs; scaling of equipment unit costs; a geometric effect that increases the mass power density; and reduction of the recirculating power fraction. Increased plasma size also relaxes the required confinement parameters: For the same neutron wall loading, larger tokamaks can use lower magnetic fields. Fossil-fuel power plants have a weaker economy of scale than fusion because the fuel costs constitute much of their COE. Solar and wind power plants consist of many small units, so they have little economy of scale. Fission power plants have a strong economy of scale but are unable to exploit it because the maximum unit size is limited by safety concerns. Large, steady-state fusion reactors generating 3 to 6 GW(electric) may be able to produce electricity for 4 to 5 cents/kW·h, which would be competitive with other future energy sources. 38 refs., 6 figs., 6 tabs

The Fuel Economy of Hybrid Buses: The Role of Ancillaries in Real Urban Driving

Directory of Open Access Journals (Sweden)

Francesco Bottiglione

2014-07-01

Full Text Available In the present context of the global economic crisis and environmental emergency, transport science is asked to find innovative solutions to turn traditional vehicles into fuel-saving and eco-friendly devices. In the last few years, hybrid vehicles have been shown to have potential benefits in this sense. In this paper, the fuel economy of series hybrid-electric and hybrid-mechanical buses is simulated in two real driving situations: cold and hot weather driving in the city of Taranto, in Southern Italy. The numerical analysis is carried out by an inverse dynamic approach, where the bus speed is given as a velocity pattern measured in the field tests performed on one of the city bus routes. The city of Taranto drive schedule is simulated in a typical tempered climate condition and with a hot temperature, when the air conditioning system must be switched on for passenger comfort. The fuel consumptions of hybrid-electric and hybrid-mechanical buses are compared to each other and with a traditional bus powered by a diesel engine. It is shown that the series hybrid-electric vehicle outperforms both the traditional and the mechanical hybrid vehicles in the cold weather driving simulation, reducing the fuel consumption by about 35% with respect to the traditional diesel bus. However, it is also shown that the performance of the hybrid-electric bus gets dramatically worse when the air-cooling system is continuously turned on. In this situation, the fuel consumption of the three different technologies for city buses under investigation is comparable.

California's Low-Carbon Fuel Standard - Compliance Trends

Science.gov (United States)

Witcover, J.; Yeh, S.

2013-12-01

Policies to incentivize lower carbon transport fuels have become more prevalent even as they spark heated debate over their cost and feasibility. California's approach - performance-based regulation called the Low Carbon Fuel Standard (LCFS) - has proved no exception. The LCFS aims to achieve 10% reductions in state transport fuel carbon intensity (CI) by 2020, by setting declining annual CI targets, and rewarding fuels for incremental improvements in CI beyond the targets while penalizing those that fail to meet requirements. Even as debate continues over when new, lower carbon fuels will become widely available at commercial scale, California's transport energy mix is shifting in gradual but noticeable ways under the LCFS. We analyze the changes using available data on LCFS fuels from the California Air Resources Board and other secondary sources, beginning in 2011 (the first compliance year). We examine trends in program compliance (evaluated through carbon credits and deficits generated), and relative importance of various transport energy pathways (fuel types and feedstocks, and their CI ratings, including new pathways added since the program's start). We document a roughly 2% decline in CI for gasoline and diesel substitutes under the program, with compliance achieved through small shifts toward greater reliance on fuels with lower CI ratings within a relatively stable amount of transport energy derived from alternatives to fossil fuel gasoline and diesel. We also discuss price trends in the nascent LCFS credit market. The results are important to the broader policy debate about transportation sector response to market-based policies aimed at reducing the sector's greenhouse gas emissions.

75 FR 33565 - Notice of Intent To Prepare an Environmental Impact Statement for New Medium- and Heavy-Duty Fuel...

Science.gov (United States)

2010-06-14

... ``light trucks''). Pursuant to this statutory authority, NHTSA sets Corporate Average Fuel Economy (CAFE... analysis when setting CAFE standards. \\3\\ See Light-Duty Vehicle Greenhouse Gas Emission Standards and... process similar to determining passenger car and light truck compliance with CAFE standards. (5...

Feedback controlled fuel injection system can accommodate any alcohol-gasoline blend

Energy Technology Data Exchange (ETDEWEB)

Pefley, R K; Pullman, J B; Suga, T P; Espinola, S

1980-01-01

A fuel metering system has been adapted and permits operation on all blends of alcohols and gasoline ranging from pure gasoline to pure ethanol and methanol. It is a closed loop electronic feedback controlled fuel injection system (EFI) with exhaust oxygen sensor. The system is used by Toyota Motor Company in their Supra and Cressida models in conjunction with a 3-way catalytic exhaust system. These models meet California exhaust and evaporative emission standards. An unmodified model has been tested on alcohol gasoline blends from pure gasoline to 50% ethanol-50% gasoline and 30% methanol-70% gasoline and found to meet all exhaust and evaporative emissions standards. A Cressida with modified EFI system is currently being tested. It is capable of operating on pure gasoline, pure methanol or ethanol and all intermediate blends. The testing to date shows that the vehicle meets all exhaust emissions standards while operating over the blend range from pure gasoline to pure ethanol while maintaining driveability and energy based fuel economy. The paper will present the total test evidence for all gasoline-alcohol blends. This will include exhaust and evaporative emissions, fuel economy and driveability as determined in accordance with United States Federal Test Procedures. Additionally, the paper will report experiences accumulated from road operation of the vehicle over a six-month period.

Transportation fuel from plastic: Two cases of study.

Science.gov (United States)

Faussone, Gian Claudio

2018-03-01

Synthesis of liquid fuels from waste is a promising pathway for reducing the carbon footprint of transportation industry and optimizing waste management towards zero landfilling. The study of commercial plants that conduct pyrolysis of plastics from post-consumer recycled materials and directly mine from old landfills without any pre-treatment has revealed two cases that show the feasibility of manufacturing transportation fuels via these methods. Pyrolysis oil, consisting of almost 26% hydrocarbons within the gasoline range and almost 70% within the diesel range, is upgraded to transportation fuel in the existing refinery. A batch operating plant is able to deliver relatively good quality pyrolysis oil from post-consumer plastic waste, owing to the catalyst employed. Simple distillation was also evaluated as an alternative and cheaper upgrading process into transportation fuels, meeting EN590 diesel and ISO8217 marine fuel standards. Even though the two installations are outside the European Union, they represent good examples of the "circular economy" concept envisaged by the European Union via its ambitious "Circular Economy Package [1]", providing real world data for comparison with other experimental and lab results. Copyright © 2017 Elsevier Ltd. All rights reserved.

FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Standardization of FCEVs; 2000 nendo nenryo denchi fukyu kiban seibi jigyo jidoshayo nenryo denchi fukyu kiban seibi seika hokokusho. FCEV hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the results of the FY 2000 activities for standardization of fuel cell powered vehicles and development of the infrastructures related to participation in ISO. Fuel cell powdered vehicles are believed to be the most favored vehicles of the next generation for their low emissions and fuel efficiency. The world leading automakers, including Japanese makers, have announced plans to commercialize these vehicles in 2003 to 2004. Under these situations, the discussion has been initiated to move forward standardization of the fuel cell powdered vehicles at the international conferences, e.g., ISO (International Standardization Organization) and IEC (International Electrotechnical Commission). At ISO/TC22/SC21 (Electric Vehicles) for which the Japan Electric Vehicle Association (JEVA) is in charge as the domestic council, the proposal has been made and approved to begin working towards the standardization at the conference in November 1999. Consequently, FCEV special subcommittee consisting of public organizations (including academic organizations and Ministry of Economy, Trade and Industry), automakers, automotive parts manufacturers and other organizations related to the automotive industry has been established in February 2000 under the JEVA standardization section and started the activities. The Japanese proposals for safety and fuel cell vehicle terminology will be presented to the ISO meetings to be held in May 2001 in Tokyo. (NEDO)

Innovation in the energy sector – The role of fossil fuels and developing economies

International Nuclear Information System (INIS)

Brutschin, Elina; Fleig, Andreas

2016-01-01

This paper analyzes the effects of fossil fuel rents on R&D expenditures and patent grants in the field of energy-related technology. We argue that an increasing share of fossil fuel rents lessens the innovation of new energy technologies. We consider a sample of countries beyond the common selection of OECD members and investigate innovation efforts in the energy sector of 116 countries from 1980 to 2012. We observe the gradually growing influence of resource-abundant countries on global R&D expenditures and find that increasing fossil fuel rents have a negative effect on patent grants. This study contributes to the ongoing debate concerning the potential effects of resource abundance. More importantly, it increases our understanding of innovation activities within the energy sector and further underscores the need to extend future research to countries that have not been taken into account thus far. - Highlights: • We investigate a sample of 116 countries, a pool beyond the commonly considered OECD members. • We find that high oil prices induce increased R&D expenditures in developed countries. • Fossil rents are associated with decreasing patent grants when developing economies are included. • We use multiple imputation to handle the problem of missing data.

The developments of international hydrogen and fuel cell technology standards and the response strategies in Taiwan

International Nuclear Information System (INIS)

Tso, C.

2009-01-01

The application of hydrogen and fuel cells has expanded as the technology in international markets has improved. Leading countries have focused on establishing hydrogen and fuel cell technology standards. Both the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC) continuously release new hydrogen and fuel cell related standards. Although the government of Taiwan is promoting the development of a hydrogen and fuel cell industry, it may delay the commercialized schedule if there are no hydrogen and fuel cell related standards and regulations in place. Standards and regulations must be established as quickly as possible in order to accelerate the progress of the hydrogen and fuel cell industry. This presentation reviewed the international progress in hydrogen and fuel cell development and explained Taiwan's response strategies regarding the adoption of hydrogen and fuel cell products in niche Taiwanese markets

Fixing Detroit: how far, how fast, how fuel-efficient

OpenAIRE

Kleinbaum, Rob; McManus, Walter

2009-01-01

The Automotive Industry Crisis of 2009 is the worst the industry has ever experienced. This paper helps resolve the debate on how much and fast it should change and how it should it respond to demands for increased fuel efficiency. Looking at the actions of successful corporate turnarounds, the lessons are very clear: implement broad, deep, fast change, replace the management team, and transform the culture. We modeled the impacts of different fuel economy standards on profitability and sales...

Nuclear energy in the hydrogen economy

International Nuclear Information System (INIS)

Bertel, E.; Lee, K.S.; Nordborg, C.

2004-01-01

In the framework of a sustainable development, the hydrogen economy is envisaged as an alternative scenario in substitution to the fossil fuels. After a presentation of the hydrogen economy advantages, the author analyzes the nuclear energy a a possible energy source for hydrogen production since nuclear reactors can produce both the heat and electricity required for it. (A.L.B.)

Risk and investment in the fuel cell industry

International Nuclear Information System (INIS)

Henriques, I.; Sadorsky, P.

2004-01-01

The energy industry is one of the building blocks of the new economy. Currently, the global energy industry is going through a transformation from high carbon content fuels like crude oil to less carbon content fuels like natural gas and hydrogen. Fuel cells are the backbone of the hydrogen economy. Advances in fuel cell technology have the potential to improve the living standards of people in all countries. New sources of financial capital, however, remain a problem. In the fuel cell industry, the future of a firm often depends upon the success or failure of a few key products. This tends to make these firms very risky to invest in and, as a result, makes it difficult for these firms to secure financial investment capital. Oil price movements remain one very important source of risk to fuel cell companies. Conventional wisdom suggests that higher oil prices stimulate interest in alternative energy sources like fuel cells and the stock prices of publicly traded fuel cell companies tend to perform well when oil prices are high. Lower oil prices, however, have the opposite effect. Consequently, oil price movements may affect the rates of return of the companies currently in the fuel cell industry. In this paper, we empirically analyze the stock price sensitivity of a sample of fuel cell companies to oil price risk. In particular, we look at both the impact and magnitude of oil price changes on fuel cell stock prices. Both symmetric and asymmetric oil price changes are considered. Our results indicate that oil price risk is not an important source of risk that impacts the equity returns of fuel cell companies. We find that market risk factors are much more important. We then offer suggestions on how to manage this risk. These results are useful for managers, investors, policy makers, and others who are interested in the strategic management, financing and risk management of firms building the hydrogen economy. (author)

76 FR 59922 - Greenhouse Gas Emissions Standards and Fuel Efficiency Standards for Medium- and Heavy-Duty...

Science.gov (United States)

2011-09-28

... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 49 CFR Part 535 [NHTSA 2010-0079; EPA-HQ-OAR-2010-0162; FRL-9455-1] RIN 2127-AK74 Greenhouse Gas Emissions Standards and Fuel... comprehensive Heavy-Duty National Program that will increase fuel efficiency and reduce greenhouse gas emissions...

75 FR 62739 - 2017 and Later Model Year Light Duty Vehicle GHG Emissions and CAFE Standards; Notice of Intent

Science.gov (United States)

2010-10-13

... Model Year Light Duty Vehicle GHG Emissions and CAFE Standards; Notice of Intent AGENCIES: Environmental... fuel economy (CAFE) standards in accordance with the Energy Policy and Conservation Act (EPCA), as... FR 49454, 49460 (September 28, 2009). The NHTSA CAFE standards are only based on technologies that...

Outlook for Japanese economy and energy demand in fiscal year 2015. Will decline in oil price benefit sluggish Japanese economy after tax increase?

International Nuclear Information System (INIS)

Yanagisawa, Akira; Ikarii, Ryohei; Iwata, Sohei; Wang, In-Ha; Tomokawa, K.; Shibata, Yoshiaki; Ito, Kokichi

2015-01-01

Although prompt economic recovery was expected, after tax increase in April 2014, not so much progress has been made as anticipated. One of the reasons for this is the increase in energy cost due to the decline in LNG price following that of oil price from an international point of view, and the electric rate hike resulted from the delay in restart of nuclear power plant from a domestic point of view, and so on. In this article, the outlook for the Japanese economy and the energy demand in the fiscal year 2015 and the influences of various factors were evaluated. For this evaluation, the values set as the primary premises for the standard scenario were: (1) world economy, (2) CIF prices for importing oil, LNG, and coal, (3) exchange rates, (4) nuclear power generation, (5) electricity demand, and (6) temperature. Then, the influences of following items on economy and energy demand were analyzed: (1) macro economy, (2) production activity, (3) domestic supply of primary energy, (4) final energy consumption, (5) sales amount of electricity and composition of electrical sources, (6) sales amount of city gas, (7) sales amount of fuel oil and LNG, (8) renewable energy power generation, (9) restart rate of nuclear power plant, and so on. (S.K.)

Standardized, utility-DOE compatible, spent fuel storage-transport systems

International Nuclear Information System (INIS)

Smith, M.L.

1991-01-01

Virginia Power has developed and licensed a facility for dry storage of spent nuclear fuel in metal spent fuel storage casks. The modifications to the design of these casks necessary for licensing for both storage and transport of spent fuel are discussed along with the operational advantages of dual purpose storage-transport casks. Dual purpose casks can be used for storage at utility and DOE sites (MRS or repository) and for shipment between these sites with minimal spent fuel handling. The cost for a standardized system of casks that are compatible for use at both DOE and utility sites is discussed along with possible arrangements for sharing both the cost and benefits of dual purpose storage-transport casks

Engineering-economic analyses of automotive fuel economy potential in the United States

Energy Technology Data Exchange (ETDEWEB)

Greene, D.L.; DeCicco, J.

2000-02-01

Over the past 25 years more than 20 major studies have examined the technological potential to improve the fuel economy of passenger cars and light trucks in the US. The majority has used technology/cost analysis, a combination of analytical methods from the disciplines of economics and automotive engineering. In this paper the authors describe the key elements of this methodology, discuss critical issues responsible for the often widely divergent estimates produced by different studies, review the history of its use, and present results from six recent assessments. Whereas early studies tended to confine their scope to the potential of proven technology over a 10-year time period, more recent studies have focused on advanced technologies, raising questions about how best to include the likelihood of technological change. The paper concludes with recommendations for further research.

Diesel engine performance as influenced by fuel temperature

Energy Technology Data Exchange (ETDEWEB)

Sumner, H.R.; Best, W.D.; Monroe, G.E.

1986-11-01

The effects of diesel fuel temperature on the efficiency of a 4.4-L diesel engine were studied. Fuel temperatures of 41, 67, and 81 C were used with engine loads of 0 to 100% of full load at three engine frequencies. Regression equations were developed that predicted fuel economy as a function of PTO power at three engine frequencies. An increase in engine fuel temperature did not improve fuel economy, but did result in reduced fuel mass flow through the injector pump and reduced maximum PTO power. Reducing engine frequency improved fuel economy and supported the 'throttle back shift up' technique for saving fuel. 4 figs., 1 tab., 11 refs.

Hydrogen fuel. Uses

International Nuclear Information System (INIS)

Darkrim-Lamari, F.; Malbrunot, P.

2006-01-01

Hydrogen is a very energetic fuel which can be used in combustion to generate heat and mechanical energy or which can be used to generate electricity and heat through an electrochemical reaction with oxygen. This article deals with the energy conversion, the availability and safety problems linked with the use of hydrogen, and with the socio-economical consequences of a generalized use of hydrogen: 1 - hydrogen energy conversion: hydrogen engines, aerospace applications, fuel cells (principle, different types, domains of application); 2 - hydrogen energy availability: transport and storage (gas pipelines, liquid hydrogen, adsorbed and absorbed hydrogen in solid materials), service stations; 3 - hazards and safety: flammability, explosibility, storage and transport safety, standards and regulations; 4 - hydrogen economy; 5 - conclusion. (J.S.)

NRC committee on assessment of technologies for improving fuel economy of light-duty vehicles: Meeting with DOT Volpe Center staff - February 27, 2013

Science.gov (United States)

2013-02-27

On February 27, 2013 National Research Council's Committee on Fuel Economy of Light-Duty Vehicles, Phase 2 held a meeting at the John A. Volpe National Transportation Systems Center on the Volpe Model and Other CAFE Issues. The meeting objectives wer...

40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Science.gov (United States)

2010-07-01

... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.520 What are the standards and dye requirements for motor vehicle diesel...

Standard casks for the transport of LWR spent fuel. Storage/transport casks for long cooled spent fuel

International Nuclear Information System (INIS)

Blum, P.; Sert, G.; Gagnon, R.

1983-01-01

During the past decade, TRANSNUCLEAIRE has developed, licensed and marketed a family of standard casks for the transport of spent fuel from LWR reactors to reprocessing plants and the ancillary equipments necessary for their operation and transport. A large number of these casks are presently used for European and intercontinental transports and manufactured under TRANSNUCLEAIRE supervision in different countries. The main advantages of these casks are: - large payload for considered modes of transport, - moderate cost, - reliability due to the large experience gained by TRANSNUCLEAIRE as concerns fabrication and operation problems, - standardization faciliting fabrication, operation and spare part supply. Recently, TRANSNUCLEAIRE also developed a new generation of casks for the dry storage and occasional transport of LWR spent fuel which has been cooled for 5 years or 7 years in case of consolidated fuel rods. These casks have an optimum payload which takes into account the shielding requirements and the weight limitations at most sites. This paper deals more particularly with the TN 24 model which exists in 4 versions among which one for 24 PWR 900 fuel assemblies and another one for the consolidated fuel rods from 48 of same fuel assemblies

Outlook of Japan's economy and energy demand for FY2017

International Nuclear Information System (INIS)

Aoshima, Momoko; Yorita, Y.; Tsunoda, M.

2017-01-01

This paper disclosed the prospects of Japan's economy and energy demand as the standard scenario, with the following major preconditions in mind: (1) world economy grows moderately, (2) supply and demand of crude oil are gently balanced, (3) exchange rate is Yen110/$, (4) nuclear power generation gradually moves back to operation, and the number of cumulative reopening units until the end of FY2017 reaches 14, and (5) supply and demand of electric power can secure 3% supply reserve ratio necessary for stable supply of electricity nationwide. In addition, this paper carried out evaluation analyses on the following various influences: macro economy, production activity, primary energy domestic supply, final energy consumption, electricity sales volume and power source composition (electric power companies), city gas sales volume (gas companies), fuel oil and LPG sales volume and crude oil throughput, renewable energy power generation, impact of nuclear power plant restart base, income/expenditure for on renewable energy generation, and impact of realization of large scale coal thermal power plant plan. (A.O.)

New technology and fuel cycles

International Nuclear Information System (INIS)

Mooradian, A.J.

1979-06-01

The means of improving uranium utilization in nuclear power reactors are reviewed with respect to economic considerations, assurance of adequate fuel supplies and risk of weapons proliferation. Reference is made to what can be done to improve fuel economy in existing reactor systems operating on a once-through fuel cycle and the potential for improvement offered by fuel recycle in those systems. The state of development of new reactor systems that offer significant savings in uranium utilization is also reviewed and conclusions are made respecting the policy implications of the search for fuel economy. (author)

Hydrogen energy stations: along the roadside to the hydrogen economy

International Nuclear Information System (INIS)

Clark, W.W.; Rifkin, J.; O'Connor, T.; Swisher, J.; Lipman, T.; Rambach, G.

2005-01-01

Hydrogen has become more than an international topic of discussion within government and among industry. With the public announcements from the European Union and American governments and an Executive Order from the Governor of California, hydrogen has become a ''paradigm change'' targeted toward changing decades of economic and societal behaviours. The public demand for clean and green energy as well as being ''independent'' or not located in political or societal conflict areas, has become paramount. The key issues are the commitment of governments through public policies along with corporations. Above all, secondly, the advancement of hydrogen is regional as it depends upon infrastructure and fuel resources. Hence, the hydrogen economy, to which the hydrogen highway is the main component, will be regional and creative. New jobs, businesses and opportunities are already emerging. And finally, the costs for the hydrogen economy are critical. The debate as to hydrogen being 5 years away from being commercial and available in the marketplace versus needing more research and development contradicts the historical development and deployment of any new technology be it bio-science, flat panel displays, computers or mobile phones. The market drivers are government regulations and standards soon thereafter matched by market forces and mass production. Hydrogen is no different. What this paper does is describes is how the hydrogen highway is the backbone to the hydrogen economy by becoming, with the next five years, both regional and commercial through supplying stationary power to communities. Soon thereafter, within five to ten years, these same hydrogen stations will be serving hundreds and then thousands of hydrogen fuel powered vehicles. Hydrogen is the fuel for distributed energy generation and hence positively impacts the future of public and private power generators. The paradigm has already changed. (author)

Analysis of economy characteristics and improvement ways for China nuclear power

International Nuclear Information System (INIS)

Li Yong

2010-01-01

For the nuclear power industry, due to characteristics of its own, its economy is quite different from that of the traditional fossil-fuel power. This paper studied the basic characteristics of the nuclear power economy and the status of economy of domestic nuclear power, and analyzed the main ways to improve the nuclear power economy. (authors)

Oxidative dissolution of ADOPT compared to standard UO2 fuel

International Nuclear Information System (INIS)

Nilsson, Kristina; Roth, Olivia; Jonsson, Mats

2017-01-01

In this work we have studied oxidative dissolution of pure UO 2 and ADOPT (UO 2 doped with Al and Cr) pellets using H 2 O 2 and gammaradiolysis to induce the process. There is a small but significant difference in the oxidative dissolution rate of UO 2 and ADOPT pellets, respectively. However, the difference in oxidative dissolution yield is insignificant. Leaching experiments were also performed on in-reactor irradiated ADOPT and UO 2 pellets under oxidizing conditions. The results indicate that the U(VI) release is slightly slower from the ADOPT pellet compared to the UO 2. This could be attributed to differences in exposed surface area. However, fission products with low UO 2 solubility display a higher relative release from ADOPT fuel compared to standard UO 2 -fuel. This is attributed to a lower matrix solubility imposed by the dopants in ADOPT fuel. The release of Cs is higher from UO 2 which is attributed to the larger grain size of ADOPT. - Highlights: •Oxidative dissolution of ADOPT fuel is compared to standard UO 2 fuel. •Only marginal differences are observed. •The main difference observed is in the relative release rate of fission products. •Differences are claimed to be attributed to a lower matrix solubility imposed by the dopants in ADOPT fuel.

Gaining Control of Iraq's Shadow Economy

National Research Council Canada - National Science Library

Ramirez, David S

2007-01-01

.... These conditions fuel a sprawling, decades-old shadow economy manipulated by elements of organized crime, militias, and insurgents to fund attacks on Coalition forces, infrastructure and innocent Iraqi civilians...

About economy of fuel and energy resources in the hot water supply system

Science.gov (United States)

Rotov, P. V.; Sivukhin, A. A.; Zhukov, D. A.; Zhukova, A. V.

2017-11-01

The assessment of the power efficiency realized in the current of heat supply system of technology of regulation of loading of the hot water supply system, considering unevenness consumption of hot water is executed. For the purpose of definition the applicability boundary of realized technology comparative analysis of indicators of the effectiveness of its work within the possible range of the parameters of regulations. Developed a software application “The calculation of the total economy of fuel and energy resources in the hot water supply system when you change of the parameters of regulations”, which allows on the basis of multivariate calculations analyses of their results, to choose the optimum mode of operation heat supply system and to assess the effectiveness of load regulation in the hot water supply system.

Japan's plutonium economy

International Nuclear Information System (INIS)

Hecht, M.M.

1994-01-01

Japan's plutonium economy is based on the most efficient use of nuclear energy, as envisioned under the Atoms for Peace program of the 1950s and 1960s. The nuclear pioneers assumed that all nations would want to take full advantage of atomic energy, recycling waste into new fuel to derive as much energy as possible from this resource

Gasoline Ultra Efficient Fuel Vehicle with Advanced Low Temperature Combustion

Energy Technology Data Exchange (ETDEWEB)

Confer, Keith [Delphi Automotive Systems, LLC, Troy, MI (United States)

2014-12-18

The objective of this program was to develop, implement and demonstrate fuel consumption reduction technologies which are focused on reduction of friction and parasitic losses and on the improvement of thermal efficiency from in-cylinder combustion. The program was executed in two phases. The conclusion of each phase was marked by an on-vehicle technology demonstration. Phase I concentrated on short term goals to achieve technologies to reduce friction and parasitic losses. The duration of Phase I was approximately two years and the target fuel economy improvement over the baseline was 20% for the Phase I demonstration. Phase II was focused on the development and demonstration of a breakthrough low temperature combustion process called Gasoline Direct- Injection Compression Ignition (GDCI). The duration of Phase II was approximately four years and the targeted fuel economy improvement was 35% over the baseline for the Phase II demonstration vehicle. The targeted tailpipe emissions for this demonstration were Tier 2 Bin 2 emissions standards.

Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

OpenAIRE

Krivtsov, Sergey; Syrbakov, Andrey Pavlovich; Korchuganova, Mariya Anatolievna

2016-01-01

This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

Science.gov (United States)

Krivtsov, Sergey N.; Syrbakov, Andrey P.; Korchuganova, Marina A.

2016-08-01

This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

Alternative Fuels DISI Engine Research ? Autoignition Metrics.

Energy Technology Data Exchange (ETDEWEB)

Sjoberg, Carl Magnus Goran [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Vuilleumier, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-02-01

Improved engine efficiency is required to comply with future fuel economy standards. Alternative fuels have the potential to enable more efficient engines while addressing concerns about energy security. This project contributes to the science base needed by industry to develop highly efficient direct injection spark igniton (DISI) engines that also beneficially exploit the different properties of alternative fuels. Here, the emphasis is on quantifying autoignition behavior for a range of spark-ignited engine conditions, including directly injected boosted conditions. The efficiency of stoichiometrically operated spark ignition engines is often limited by fuel-oxidizer end-gas autoignition, which can result in engine knock. A fuel’s knock resistance is assessed empirically by the Research Octane Number (RON) and Motor Octane Number (MON) tests. By clarifying how these two tests relate to the autoignition behavior of conventional and alternative fuel formulations, fuel design guidelines for enhanced engine efficiency can be developed.

41 CFR 102-34.55 - Are there fleet average fuel economy standards we must meet?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Are there fleet average... Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION PERSONAL PROPERTY 34-MOTOR VEHICLE MANAGEMENT Obtaining Fuel Efficient Motor Vehicles § 102-34.55 Are there fleet...

The Transportation Leapfrog: Using Smart Phones to Collect Driving Data and Model Fuel Economy in India

Energy Technology Data Exchange (ETDEWEB)

Gopal, Anand [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Schewel, Laura [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Saxena, Samveg [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Phadke, Amol [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

2013-05-01

Car ownership in India is expected to skyrocket in the coming decades, strongly driven by rising incomes. This phenomenon provides unprecedented opportunities for automakers and equally unprecedented social and environmental challenges. Policymakers, urban planners and civil society see this car boom leading to an explosion in problems related to congestion, infrastructure, air pollution, safety, higher oil imports and climate change. For all these stakeholders to take effective action, good data on how people use their cars, their demand for mobility and their behavior in mobility is essential. Unfortunately, there is very little data on the Indian transport sector as a whole and virtually none on real-world vehicle performance and use. The rapid development of high quality mobile telecommunications infrastructure provides India with the opportunity to leapfrog the West in cheaply collecting vast amounts of useful data from transportation. In this paper, we describe a pilot project in which we use commercial smart phone apps to collect per second car driving data from the city of Pune, instantly upload it through 3G and prepare it for analysis using advanced noise filtering algorithms for less than $1 per day per car. We then use our data in an Autonomie simulation to show that India’s currently planned fuel economy test procedures will result in over-estimates of fuel economy of approximately 35% for a typical Indian car when it is operated in real world conditions. Supporting better driving cycle development is just one of many applications for smart phone derived data in Indian transportation.

Hydrogen economy: a little bit more effort

International Nuclear Information System (INIS)

Pauron, M.

2008-01-01

In few years, the use of hydrogen in economy has become a credible possibility. Today, billions of euros are invested in the hydrogen industry which is strengthened by technological advances in fuel cells development and by an increasing optimism. However, additional research efforts and more financing will be necessary to make the dream of an hydrogen-based economy a reality

On the hazard accumulation of actinide waste in a Pu-fueled LMFBR power economy with and without by-product actinide recycling

International Nuclear Information System (INIS)

Anselmi, L.; Caruso, K.; Hage, W.; Schmidt, E.

1979-01-01

The actinide waste arisings in terms of hazard potential for ingestion and inhalation are given for a Pu-fueled LMFBR Power Economy as function of decay time. The data were assessed for two simplified fuel cycles, one considering the recycling of by-product actinides and the other their complete discharge to the high-level waste. Two durations of nuclear power and several loss fractions of actinides to the waste were considered. The major contributors in form of chemical elements or isotopes to the actinide waste hazard built up during the nuclear power duration were identified for various decay intervals

An optimized BWR fuel lattice for improved fuel utilization

International Nuclear Information System (INIS)

Bernander, O.; Helmersson, S.; Schoen, C.G.

1984-01-01

Optimization of the BWR fuel lattice has evolved into the water cross concept, termed ''SVEA'', whereby the improved moderation within bundles augments reactivity and thus improves fuel cycle economy. The novel design introduces into the assembly a cruciform and double-walled partition containing nonboiling water, thus forming four subchannels, each of which holds a 4x4 fuel rod bundle. In Scandinavian BWRs - for which commercial SVEA reloads are now scheduled - the reactivity gain is well exploited without adverse impact in other respects. In effect, the water cross design improves both mechanical and thermal-hydraulic performance. Increased average burnup is also promoted through achieving flatter local power distributions. The fuel utilization savings are in the order of 10%, depending on the basis of comparison, e.g. choice of discharge burnup and lattice type. This paper reviews the design considerations and the fuel utilization benefits of the water cross fuel for non-Scandinavian BWRs which have somewhat different core design parameters relative to ASEA-ATOM reactors. For one design proposal, comparisons are made with current standard 8x8 fuel rod bundles as well as with 9x9 type fuel in reactors with symmetric or asymmetric inter-assembly water gaps. The effect on reactivity coefficients and shutdown margin are estimated and an assessment is made of thermal-hydraulic properties. Consideration is also given to a novel and advantageous way of including mixed-oxide fuel in BWR reloads. (author)

My 2030s. Citizens about the Biobased Economy; My 2030s. Burgers over de Biobased Economy

Energy Technology Data Exchange (ETDEWEB)

Van den Berg, N.; Hulshof, M.; Van der Veen, M.

2013-02-15

My 2030s is the first qualitative study of the needs and concerns of citizens about the Biobased Economy, an economy in which fossil fuels are largely substituted by vegetable alternatives. This final report describes the reason and purpose of My 2030s, the course of the public debates and the results of research into ideas of citizens on the Biobased Economy The report concludes with recommendations on how the stakeholders can actively involve citizens in one of the major transitions of the next century [Dutch] My 2030s is het eerste kwalitatieve onderzoek naar de wensen en zorgen van burgers over de Biobased Economy, een economie waarin fossiele grondstoffen grotendeels zijn vervangen door plantaardige alternatieven. Dit eindrapport beschrijft de aanleiding en opzet van My 2030s, het verloop van de publieksdebatten en de resultaten van het onderzoek naar denkbeelden van burgers over de Biobased Economy. Het rapport eindigt met aanbevelingen over hoe de stakeholders burgers actief kunnen betrekken bij een van de belangrijkste transities van de komende eeuw.

Global environmental impacts of the hydrogen economy

International Nuclear Information System (INIS)

Derwent, R.; Simmonds, P.; O'Doherty, S.; Manning, A.; Collins, W.; Stevenson, D.

2006-01-01

Hydrogen-based energy systems appear to be an attractive proposition in providing a future replacement for the current fossil-fuel based energy systems. Hydrogen is an important, though little studied, trace component of the atmosphere. It is present at the mixing ratio of about 510 ppb currently and has important man-made and natural sources. Because hydrogen reacts with tropospheric hydroxyl radicals, emissions of hydrogen to the atmosphere perturb the distributions of methane and ozone, the second and third most important greenhouse gases after carbon dioxide. Hydrogen is therefore an indirect greenhouse gas with a global warming potential GWP of 5.8 over a 100-year time horizon. A future hydrogen economy would therefore have greenhouse consequences and would not be free from climate perturbations. If a global hydrogen economy replaced the current fossil fuel-based energy system and exhibited a leakage rate of 1%, then it would produce a climate impact of 0.6% of the current fossil fuel based system. Careful attention must be given to reduce to a minimum the leakage of hydrogen from the synthesis, storage and use of hydrogen in a future global hydrogen economy if the full climate benefits are to be realised. (author)

78 FR 63375 - List of Approved Spent Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS® Cask System

Science.gov (United States)

2013-10-24

... Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS[supreg] Cask System AGENCY: Nuclear...] Cask System listing within the ``List of Approved Spent Fuel Storage Casks'' to include Amendment No..., Inc. Standardized NUHOMS[supreg] Cask System listing within the ``List of Approved Spent Fuel Storage...

Alcohol fuels for developing countries

International Nuclear Information System (INIS)

Bhattacharya, Partha

1993-01-01

The importance of alcohol as an alternative fuel has been slowly established. In countries such as Brazil, they are already used in transport and other sectors of economy. Other developing countries are also trying out experiments with alcohol fuels. Chances of improving the economy of many developing nations depends to a large extent on the application of this fuel. The potential for alcohol fuels in developing countries should be considered as part of a general biomass-use strategy. The final strategies for the development of alcohol fuel will necessarily reflect the needs, values, and conditions of the individual nations, regions, and societies that develop them. (author). 5 refs

Conversion and standardization of university reactor fuels using low-enrichment uranium - options and costs

International Nuclear Information System (INIS)

Harris, D.R.; Matos, J.E.; Young, H.H.

1985-01-01

The highly-enriched uranium (HEU) fuel used in twenty United States university reactors can be viewed as contributing to the risk of theft or diversion of weapons-useable material. The US Nuclear Regulatory Commission has issued a policy statement expressing its concern and has published a proposed rule on limiting the use of HEU in NRC-licensed non-power reactors. The fuel options, functional impacts, licensing, and scheduling of conversion and standardization of these reactor fuels to use of low-enrichment uranium (LEU) have been assessed. The university reactors span a wide range in form and function, from medium-power intense neutron sources where HEU fuel may be required, to low-power training and research facilities where HEU fuel is unnecessary. Conversion provides an opportunity to standardize university reactor fuels and improve reactor utilization in some cases. The entire program is estimated to cost about $10 million and to last about five years. Planning for conversion and standardization is facilitated by the US Department of Energy. 20 refs., 1 tab

Conversion and standardization of university reactor fuels using low-enrichment uranium - Options and costs

International Nuclear Information System (INIS)

Harris, D.R.; Matos, J.E.; Young, H.H.

1985-01-01

The highly-enriched uranium (HEU) fuel used in twenty United States university reactors can be viewed as contributing to the risk of theft or diversion of weapons-useable material. The U.S. Nuclear Regulatory Commission has issued a policy statement expressing its concern and has published a proposed rule on limiting the use of HEU in NRC-licensed non-power reactors. The fuel options, functional impacts, licensing, and scheduling of conversion and standardization of these reactor fuels to use of low-enrichment uranium (LEU) have been assessed. The university reactors span a wide range in form and function, from medium-power intense neutron sources where HEU fuel may be required, to low-power training and research facilities where HEU fuel is unnecessary. Conversion provides an opportunity to standardize university reactor fuels and improve reactor utilization in some cases. The entire program is estimated to cost about $10 million and to last about five years. Planning for conversion and standardization is facilitated by the U.S. Department of Energy. (author)

Creating NDA working standards through high-fidelity spent fuel modeling

International Nuclear Information System (INIS)

Skutnik, Steven E.; Gauld, Ian C.; Romano, Catherine E.; Trellue, Holly

2012-01-01

The Next Generation Safeguards Initiative (NGSI) is developing advanced non-destructive assay (NDA) techniques for spent nuclear fuel assemblies to advance the state-of-the-art in safeguards measurements. These measurements aim beyond the capabilities of existing methods to include the evaluation of plutonium and fissile material inventory, independent of operator declarations. Testing and evaluation of advanced NDA performance will require reference assemblies with well-characterized compositions to serve as working standards against which the NDA methods can be benchmarked and for uncertainty quantification. To support the development of standards for the NGSI spent fuel NDA project, high-fidelity modeling of irradiated fuel assemblies is being performed to characterize fuel compositions and radiation emission data. The assembly depletion simulations apply detailed operating history information and core simulation data as it is available to perform high fidelity axial and pin-by-pin fuel characterization for more than 1600 nuclides. The resulting pin-by-pin isotopic inventories are used to optimize the NDA measurements and provide information necessary to unfold and interpret the measurement data, e.g., passive gamma emitters, neutron emitters, neutron absorbers, and fissile content. A key requirement of this study is the analysis of uncertainties associated with the calculated compositions and signatures for the standard assemblies; uncertainties introduced by the calculation methods, nuclear data, and operating information. An integral part of this assessment involves the application of experimental data from destructive radiochemical assay to assess the uncertainty and bias in computed inventories, the impact of parameters such as assembly burnup gradients and burnable poisons, and the influence of neighboring assemblies on periphery rods. This paper will present the results of high fidelity assembly depletion modeling and uncertainty analysis from independent

Toxic economy - interferences with recent Romanian experience

Directory of Open Access Journals (Sweden)

Cristian Gheorghe Iacob

2015-05-01

Full Text Available What is the toxic economy? Economy through which the legislation and control in place, fails to provide a standard of living with sustainable uptrend, getting to transform assets into cash whose value is consumed unproductively. Why we do not live well? Good life is in fact the standard of living of the economic and political offered by the laws of a state or groups of states, citizens living on a certain territory. The standard of living is a result of variety of factors, difficult to quantify both separately and in particular unit. In this article we will try to define the fractal complexity of how the toxic economy is affecting the standard of leaving

Automobile fuel economy : potential effects of increasing the corporate average fuel economy standards

Science.gov (United States)

2000-08-01

Between 1981 and 1999, the average price of gasoline, adjusted for inflation, declined more than 60 percent. During the same period, the U.S. transportation sector's consumption of oil rose from less than 10 million to nearly 13 million barrels per d...

[U.S. renewable fuel standard implementation mechanism and market tracking].

Science.gov (United States)

Kang, Liping; Earley, Robert; An, Feng; Zhang, Yu

2013-03-01

U.S. Renewable Fuel Standard (RFS) is a mandatory policy for promoting the utilization of biofuels in road transpiration sector in order to reduce the country's dependency on foreign oil and greenhouse gas emissions. U.S. Environmental Protection Agency (EPA) defines the proportion of renewable fuels according to RFS annual target, and requests obligated parties such like fossil fuel refiner, blenders and importer in the U.S. to complete Renewable Volume Obligation (RVO) every year. Obligated parties prove they have achieved their RVO through a renewable fuels certification system, which generates Renewable Identification Numbers (RINs) for every gallon of qualified renewable fuels produced or imported into U.S., RINs is a key for tracking renewable fuel consumption, which in turn is a key for implementing the RFS in the U.S., separated RINs can be freely traded in market and obligated parties could fulfill their RVO through buying RINs from other stakeholders. This briefing paper highlights RFS policy implementing mechanism and marketing tracking, mainly describes importance of RINs, and the method for generating and tracking RINs by both government and fuels industry participants.

Oxidative dissolution of ADOPT compared to standard UO{sub 2} fuel

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Kristina [School of Chemical Science and Engineering, Applied Physical Chemistry, KTH Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Roth, Olivia [Studsvik Nuclear AB, SE-611 82 Nyköping (Sweden); Jonsson, Mats, E-mail: matsj@kth.se [School of Chemical Science and Engineering, Applied Physical Chemistry, KTH Royal Institute of Technology, SE-100 44 Stockholm (Sweden)

2017-05-15

In this work we have studied oxidative dissolution of pure UO{sub 2} and ADOPT (UO{sub 2} doped with Al and Cr) pellets using H{sub 2}O{sub 2} and gammaradiolysis to induce the process. There is a small but significant difference in the oxidative dissolution rate of UO{sub 2} and ADOPT pellets, respectively. However, the difference in oxidative dissolution yield is insignificant. Leaching experiments were also performed on in-reactor irradiated ADOPT and UO{sub 2} pellets under oxidizing conditions. The results indicate that the U(VI) release is slightly slower from the ADOPT pellet compared to the UO{sub 2.} This could be attributed to differences in exposed surface area. However, fission products with low UO{sub 2} solubility display a higher relative release from ADOPT fuel compared to standard UO{sub 2}-fuel. This is attributed to a lower matrix solubility imposed by the dopants in ADOPT fuel. The release of Cs is higher from UO{sub 2} which is attributed to the larger grain size of ADOPT. - Highlights: •Oxidative dissolution of ADOPT fuel is compared to standard UO{sub 2} fuel. •Only marginal differences are observed. •The main difference observed is in the relative release rate of fission products. •Differences are claimed to be attributed to a lower matrix solubility imposed by the dopants in ADOPT fuel.

A review on idling reduction strategies to improve fuel economy and reduce exhaust emissions of transport vehicles

International Nuclear Information System (INIS)

Shancita, I.; Masjuki, H.H.; Kalam, M.A.; Rizwanul Fattah, I.M.; Rashed, M.M.; Rashedul, H.K.

2014-01-01

Highlights: • Introduce various idling reduction technologies for transport vehicles. • Exhibit their energy use, advantages, disadvantages to understand their capability. • Conduct critical review to improve fuel economy and exhaust emissions. • Suggest better technology according to their performance ability. - Abstract: To achieve reductions in vehicle idling, strategies and actions must be taken to minimize the time spent by drivers idling their engines. A number of benefits can be obtained in limiting the idling time. These benefits include savings in fuel use and maintenance costs, vehicle life extension, and reduction in exhaust emissions. The main objective of idling reduction (IR) devices is to reduce the amount of energy wasted by idling trucks, rail locomotives, and automobiles. During idling, gasoline vehicles emit a minimum amount of nitrogen oxides (NO x ) and negligible particulate matter (PM). However, generally a large amount of carbon monoxide (CO) and hydrocarbons (HC) are produced from these vehicles. Gasoline vehicles consume far more fuel at an hourly rate than their diesel counterparts during idling. Higher NOx and comparatively larger PM are produced by diesel vehicles than gasoline vehicles on the average during idling. Auxiliary power unit (APU), direct-fired heaters, fuel cells, thermal storage system, truck stop electrification, battery-based systems, engine idle management (shutdown) systems, electrical (shore power) solutions, cab comfort system, and hybridization are some of the available IR technologies whose performances for reducing fuel consumption and exhaust emissions have been compared. This paper analyzes the availability and capability of most efficient technologies to reduce fuel consumption and exhaust emissions from diesel and gasoline vehicles by comparing the findings of previous studies. The analysis reveals that among all the options direct fired heaters, APUs and electrified parking spaces exhibit better

40 CFR 80.524 - What sulfur content standard applies to motor vehicle diesel fuel downstream of the refinery or...

Science.gov (United States)

2010-07-01

... to motor vehicle diesel fuel downstream of the refinery or importer? 80.524 Section 80.524 Protection... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.524 What sulfur content standard...

Integration of Forest Fuel Handling in the Ordinary Forestry. Studies on Forestry, Technology and Economy of Forest Fuel Production in Lithuania

Energy Technology Data Exchange (ETDEWEB)

Andersson, Lars [Regional Forestry Board of Vaermland-Oerebro, Karlstad (Sweden); Budrys, Renatas [Lithuanian Forest Research Inst. (Lithuania)

2002-07-01

During the year 2000, The Swedish Forest Administration and Forest Department, Ministry of Environment in Lithuania, started a bilateral co-operation project, named: 'Swedish Lithuanian Wood Fuel Development Project', financed by the Swedish Energy Agency. The project was divided into 2 phases. The first phase objectives were to make a feasibility study in the eastern part of Lithuania and to identify the present conditions for the utilization of wood fuel within seven state forest enterprises and to define a demonstration and experimental area for the phase 2. The purpose of this work was to find solutions for creating horizontal and vertical integration in the handling of forest fuels in ordinary forestry and supply systems. The aim would be to give specific recommendations on which methods are the most suitable and profitable and on what type of equipment to use for various conditions and by the means of demonstrations to show how to integrate the positive results into the ordinary forestry activities. Different kinds of activities have been carried out to ensure capacity building and development on other levels within the system. 3 activity groups were established and have been working side by side with the appointed team leaders for each activity group from the institutions leading in the specific area within the forest sector in Lithuania. Swedish specialists from the Swedish Forest Administration were involved into the project and the activity groups as well. Lithuanian Forest Research Institute was involved into the project with research support. Additional to the project a mobile drum wood chipper was purchased from Sweden. 3 separate investigations have been conducted, one by Kaunas Univ. of Tech. on the analysis and estimation of material balance in Lithuania saw milling industry, another by Forest Economy Centre on wood fuel produced in industry in Lithuania and the third one by Lithuanian Energy Institute and AF international on Bio fuel

Ways of reducing radiation exposure in a future nuclear power economy

International Nuclear Information System (INIS)

Morgan, K.Z.

1976-01-01

The reasons for attempting to reduce radiation exposure in a future nuclear power economy are first discussed. This is followed by a detailed examination of ways for reducing exposures. The entire fuel cycle from uranium mining through fuel reprocessing is covered but special attention is devoted to reactors, fuel and waste shipping and fuel reprocessing

Fuel economy and torque tracking in camless engines through optimization of neural networks

International Nuclear Information System (INIS)

Ashhab, Moh'd Sami S.

2008-01-01

The feed forward controller of a camless internal combustion engine is modeled by inverting a multi-input multi-output feed forward artificial neural network (ANN) model of the engine. The engine outputs, pumping loss and cylinder air charge, are related to the inputs, intake valve lift and closing timing, by the artificial neural network model, which is trained with historical input-output data. The controller selects the intake valve lift and closing timing that will mimimize the pumping loss and achieve engine torque tracking. Lower pumping loss means better fuel economy, whereas engine torque tracking gurantees the driver's torque demand. The inversion of the ANN is performed with the complex method constrained optimization. How the camless engine inverse controller can be augmented with adaptive techniques to maintain accuracy even when the engine parts degrade is discussed. The simulation results demonstrate the effectiveness of the developed camless engine controller

Plutonium economy

International Nuclear Information System (INIS)

Traube, K.

1984-01-01

The author expresses his opinion on the situation, describes the energy-economic setting, indicates the alternatives: fuel reprocessing or immediate long-term storage, and investigates the prospects for economic utilization of the breeder reactors. All the facts suggest that the breeder reactor will never be able to stand economic competition with light-water reactors. However, there is no way to prove the future. It is naive to think that every doubt could and must be removed before stopping the development of breeder reactors - and thus also the reprocessing of the fuel of light-water reactors. On the basis of the current state of knowledge an unbiased cost-benefit-analysis can only lead to the recommendation to stop construction immediately. But can 'experts', who for years or even decades have called for and supported the development of breeder reactors be expected to make an unbiased analysis. Klaus Traube strikes the balance of the state Germany's nuclear economy is in: although there is no chance of definitively abandoning that energy-political cul-de-sac, no new adventures must be embarked upon. Responsible handling of currently used nuclear technology means to give up breeder technology and waive plutonium economy. It is no supreme technology with the aid of which structural unemployment or any other economic problem could be solved. (orig.) [de

Standard for assessment of fuel integrity under anticipated operational occurrences in BWR power plant:2002

International Nuclear Information System (INIS)

Mishima, Kaichiro; Suzuki, Riichiro; Komura, Seiichi; Kudo, Yoshiro; Yamanaka, Akihiro; Oomizu, Satoru; Kitamura, Hideya; Nagata, Yoshifumi

2003-01-01

To secure fuel integrity, a Light Water Reactor (LWR) core is designed so that no boiling transition (BT) should take place in fuel assemblies and excessive rise in fuel cladding temperature due to deteriorated that transfer should be avoided in Anticipated Operational Occurrences (AOO). In some AOO in a Boiling Water Reactor (BWR), however, the rise in reactor power could be limited by SCRAM or void reactivity effect. Recent studies have provided accumulated knowledge that even if BT takes place in fuel assemblies, the rise in fuel cladding temperature could be so small that it will not threat to fuel integrity, as long as the BT condition terminates within a short period of time. In addition, appropriate methods have been developed to evaluate the cladding temperature during dryout. This standard provides requirements in the assessment of fuel integrity under AOO in which limited-BT condition is temporarily reached and the propriety of reusing a fuel assembly that has experienced limited-BT condition. The standard has been approved by the Atomic Energy Society of Japan following deliberation by impartial members for two and half years. It is now expected that this standard will provide an effective measure for the rational expansion of fuel design and operational margin. (author)

Fueling the Gig Economy: A Case Study Evaluation of Upwork.com

Directory of Open Access Journals (Sweden)

Daryl D. Green

2018-02-01

Full Text Available With recent downsizing of talented professionals and the power of globalization to provide opportunities for more underdeveloped countries, the gig economy is a source of influence in today’s generation of professionals. Online outsourcing media have shown to be valuable resources for companies who need a specific set of skills for a limited period. This case study evaluates Upwork.com, one of the leading freelance websites in the gig economy; this article provides insights on how others should evaluate the power of this new economy in terms of opportunities for small businesses, entrepreneurs, and freelancers. Upwork has led the pack by providing a flexible platform for freelancers worldwide, including coders, writers, and web developers, putting businesses in touch with reasonably priced workers. The study begins by exploring the attributes of the gig economy. Data collection is achieved through qualitative analysis. The application of these conclusions could increase the survival rate of new freelancers on Upwork.com and in the gig economy. The study is significant because this research widens contemporary assumptions about strategic thinking for individuals engaged in e-commerce.

Methodical Approach to Estimation of Energy Efficiency Parameters of the Economy Under the Structural Changes in the Fuel And Energy Balance (on the Example of Baikal Region

Directory of Open Access Journals (Sweden)

Boris Grigorievich Saneev

2013-12-01

Full Text Available The authors consider a methodical approach which allows estimating energy efficiency parameters of the region’s economy using a fuel and energy balance (FEB. This approach was tested on the specific case of Baikal region. During the testing process the authors have developed ex ante and ex post FEBs and estimated energy efficiency parameters such as energy-, electro- and heat capacity of GRP, coefficients of useful utilization of fuel and energy resources and a monetary version of FEB. Forecast estimations are based on assumptions and limitations of technologically-intensive development scenario of the region. Authors show that the main factor of structural changes in the fuel and energy balance will be the large-scale development of hydrocarbon resources in Baikal region. It will cause structural changes in the composition of both the debit and credit of FEB (namely the structure of export and final consumption of fuel and energy resources. Authors assume that the forecast structural changes of the region’s FEB will significantly improve energy efficiency parameters of the economy: energy capacity of GRP will decrease by 1,5 times in 2010– 2030, electro and heat capacity – 1,9 times; coefficients of useful utilization of fuel and energy resources will increase by 3–5 p.p. This will save about 20 million tons of fuel equivalent (about 210 billion rubles in 2011 the prices until 2030

Improvement in operating characteristics resulting from the addition of FLIP fuel to a standard TRIGA core

International Nuclear Information System (INIS)

Randall, J.D.; Feltz, D.E.; Godsey, T.A.; Schumacher, R.F.

1974-01-01

To overcome problems associated with fuel burnup the Nuclear Science Center of Texas A and M University decided to convert from standard TRIGA fuel to FLIP-TRIGA fuel. FLIP fuel, which incorporates erbium as a burnable poison and is enriched to 70 percent in U-235, has a calculated lifetime of 9/MW-years. Due to limited funds a core was designed with a central region of 35 FLIP elements surrounded by 63 standard elements. Calculations indicated that the core excess and neutron fluxes were satisfactory, but no prediction was made of the improvements in core lifetime. The reactivity loss due to burnup for a standard core was measured to be 1.54 cents/MW-day. The addition of 35 FLIP fuel elements has reduced this value to approximately 0.5 cents/MW-day. The incorporation of FLIP fuel has, therefore, increased the lifetime of the core by a factor of three using fuel that is only 20 percent more expensive. The mixed core has other advantages as well. The power coefficient is less, the effect of xenon is less, and the fluxes in experimental facilities are higher. Thus, the mixed core has significant advantages over standard TRIGA fuel. (U.S.)

76 FR 3517 - Standards of Performance for Fossil-Fuel-Fired, Electric Utility, Industrial-Commercial...

Science.gov (United States)

2011-01-20

... Standards of Performance for Fossil-Fuel-Fired, Electric Utility, Industrial-Commercial-Institutional, and... following: Category NAICS \\1\\ Examples of regulated entities Industry 221112 Fossil fuel-fired electric utility steam generating units. Federal Government 22112 Fossil fuel-fired electric utility steam...

Modeling of hybrid vehicle fuel economy and fuel engine efficiency

Science.gov (United States)

Wu, Wei

"Near-CV" (i.e., near-conventional vehicle) hybrid vehicles, with an internal combustion engine, and a supplementary storage with low-weight, low-energy but high-power capacity, are analyzed. This design avoids the shortcoming of the "near-EV" and the "dual-mode" hybrid vehicles that need a large energy storage system (in terms of energy capacity and weight). The small storage is used to optimize engine energy management and can provide power when needed. The energy advantage of the "near-CV" design is to reduce reliance on the engine at low power, to enable regenerative braking, and to provide good performance with a small engine. The fuel consumption of internal combustion engines, which might be applied to hybrid vehicles, is analyzed by building simple analytical models that reflect the engines' energy loss characteristics. Both diesel and gasoline engines are modeled. The simple analytical models describe engine fuel consumption at any speed and load point by describing the engine's indicated efficiency and friction. The engine's indicated efficiency and heat loss are described in terms of several easy-to-obtain engine parameters, e.g., compression ratio, displacement, bore and stroke. Engine friction is described in terms of parameters obtained by fitting available fuel measurements on several diesel and spark-ignition engines. The engine models developed are shown to conform closely to experimental fuel consumption and motored friction data. A model of the energy use of "near-CV" hybrid vehicles with different storage mechanism is created, based on simple algebraic description of the components. With powertrain downsizing and hybridization, a "near-CV" hybrid vehicle can obtain a factor of approximately two in overall fuel efficiency (mpg) improvement, without considering reductions in the vehicle load.

Economic evaluation of fast reactor fuel cycling

International Nuclear Information System (INIS)

Hu Ping; Zhao Fuyu; Yan Zhou; Li Chong

2012-01-01

Economic calculation and analysis of two kinds of nuclear fuel cycle are conducted by check off method, based on the nuclear fuel cycling process and model for fast reactor power plant, and comparison is carried out for the economy of fast reactor fuel cycle and PWR once-through fuel cycle. Calculated based on the current price level, the economy of PWR one-through fuel cycle is better than that of the fast reactor fuel cycle. However, in the long term considering the rising of the natural uranium's price and the development of the post treatment technology for nuclear fuels, the cost of the fast reactor fuel cycle is expected to match or lower than that of the PWR once-through fuel cycle. (authors)

Systematic Approach to Design Tailor Made Fuel Blends That Meets ASTM Standards

DEFF Research Database (Denmark)

Intikhab, S.; Kalakul, Sawitree; H., Choudhury

2015-01-01

point, vapor pressure, and heat content were determined using analytical instruments according to their respective American Society for Testing and Materials (ASTM) standards. Most of the properties complied well with the industry standards. However, model gasoline had a comparatively low RVP....... On the other hand, model diesel had a significantly higher cloud point and pour point than what is recommended. This deviation will have an impact on the cold flow properties of the fuels. For both fuels, different additives along with their composition have also been determined using the same computational...

New Economy - New Policy Rules?

NARCIS (Netherlands)

Bullard, J.; Schaling, E.

2000-01-01

The U.S. economy appears to have experienced a pronounced shift toward higher productivity over the last five years or so. We wish to understand the implications of such shifts for the structure of optimal monetary policy rules in simple dynamic economies. Accordingly, we begin with a standard

Magnesium Matrix Composite Foams-Density, Mechanical Properties, and Applications

Science.gov (United States)

2012-07-24

the USA is the 2011 Corporate Average Fuel Economy or CAFE standard. For the small car class (footprint < 3.8 m2), the current fuel economy standard...components are now available as standard components or aftermarket parts used for customization . Lightweight alloy wheels are a prominent example of...Mater. Sci. Eng. A 2001, 302, 37–45. 7. CAFE Fuel Economy. Available online: http://www.nhtsa.gov/fuel-economy (accessed on 26 June 2012). 8. Guo

Renewable energy and macroeconomic efficiency of OECD and non-OECD economies

International Nuclear Information System (INIS)

Chien, Taichen; Hu, Jin-Li

2007-01-01

This article analyzes the effects of renewable energy on the technical efficiency of 45 economies during the 2001-2002 period through data envelopment analysis (DEA). In our DEA model, labor, capital stock, and energy consumption are the three inputs and real GDP is the single output. Increasing the use of renewable energy improves an economy's technical efficiency. Conversely, increasing the input of traditional energy decreases technical efficiency. Compared to non-OECD economies, OECD economies have higher technical efficiency and a higher share of geothermal, solar, tide, and wind fuels in renewable energy. However, non-OECD economies have a higher share of renewable energy in their total energy supply than OECD economies

A hydrogen economy: opportunities and challenges

International Nuclear Information System (INIS)

Tseng, P.; Lee, J.; Friley, P.

2005-01-01

A hydrogen economy, the long-term goal of many nations, can potentially confer energy security, along with environmental and economic benefits. However, the transition from a conventional petroleum-based energy system to a hydrogen economy involves many uncertainties, such as the development of efficient fuel-cell technologies, problems in hydrogen production and its distribution infrastructure, and the response of petroleum markets. This study uses the US MARKAL model to simulate the impacts of hydrogen technologies on the US energy system and to identify potential impediments to a successful transition. Preliminary findings highlight possible market barriers facing the hydrogen economy, as well as opportunities in new R and D and product markets for bioproducts. Quantitative analysis also offers insights on policy options for promoting hydrogen technologies. (author)

40 CFR 80.527 - Under what conditions may motor vehicle diesel fuel subject to the 15 ppm sulfur standard be...

Science.gov (United States)

2010-07-01

... vehicle diesel fuel subject to the 15 ppm sulfur standard be downgraded to motor vehicle diesel fuel... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.527 Under what conditions may motor vehicle diesel fuel subject to the 15...

The Application of High Energy Ignition and Boosting/Mixing Technology to Increase Fuel Economy in Spark Ignition Gasoline Engines by Increasing EGR Dilution Capability

Energy Technology Data Exchange (ETDEWEB)

Keating, Edward [General Motors LLC, Pontiac, MI (United States); Gough, Charles [General Motors LLC, Pontiac, MI (United States)

2015-07-07

This report summarizes activities conducted in support of the project “The Application of High Energy Ignition and Boosting/Mixing Technology to Increase Fuel Economy in Spark Ignition Gasoline Engines by Increasing EGR Dilution Capability” under COOPERATIVE AGREEMENT NUMBER DE-EE0005654, as outlined in the STATEMENT OF PROJECT OBJECTIVES (SOPO) dated May 2012.

Standardization of specifications and inspection procedures for LEU plate-type research reactor fuels

International Nuclear Information System (INIS)

1988-06-01

With the transition to high density uranium LEU fuel, fabrication costs of research reactor fuel elements have a tendency to increase because of two reasons. First, the amount of the powder of the uranium compound required increases by more than a factor of five. Second, fabrication requirements are in many cases nearer the fabrication limits. Therefore, it is important that measures be undertaken to eliminate or reduce unnecessary requirements in the specification or inspection procedures of research reactor fuel elements utilizing LEU. An additional stimulus for standardizing specifications and inspection procedures at this time is provided by the fact that most LEU conversions will occur within a short time span, and that nearly all of them will require preparation of new specifications and inspection procedures. In this sense, the LEU conversions offer an opportunity for improving the rationality and efficiency of the fuel fabrication and inspection processes. This report focuses on the standardization of specifications and inspection processes of high uranium density LEU fuels for research reactors. However, in many cases the results can also be extended directly to other research reactor fuels. 15 refs, 1 fig., 3 tabs

New road map to hydrogen economy in Japan

International Nuclear Information System (INIS)

Fukuda, K.

2004-01-01

Reducing carbon dioxide emission and enhancing energy security are the most critical energy issues for construction of future energy systems. The hydrogen energy system is widely accepted as one of the most promising system options for solving such problems. Ministry of Economy, Trade and Industry(METI) of Japanese Government made public its revised introduction scenario of fuel cell vehicles(FCVs) and stationary fuel cells with a time frame of 2005 to 2030 in March, 2004. The original scenario was published in August, 2001 with the time frame of 2005 to 2020. The revised scenario could substantially be considered as New Road Map to Hydrogen Economy in Japan. In this paper the revised scenario will be introduced together with supporting data provided by the author. (author)

Fuel-management simulations for once-through thorium fuel cycle in CANDU reactors

International Nuclear Information System (INIS)

Chan, P.S.W.; Boczar, P.G.; Ellis, R.J.; Ardeshiri, F.

1999-01-01

High neutron economy, on-power refuelling and a simple fuel bundle design result in unsurpassed fuel cycle flexibility for CANDU reactors. These features facilitate the introduction and exploitation of thorium fuel cycles in existing CANDU reactors in an evolutionary fashion. Detailed full-core fuel-management simulations concluded that a once-through thorium fuel cycle can be successfully implemented in an existing CANDU reactor without requiring major modifications. (author)

78 FR 63408 - List of Approved Spent Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS® Cask System

Science.gov (United States)

2013-10-24

... Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS[supreg] Cask System AGENCY: Nuclear...] Cask System listing within the ``List of Approved Spent Fuel Storage Casks'' to include Amendment No... Safety Analysis Report for the Standardized NUHOMS[supreg] Horizontal Modular Storage System for...

The Methanol Economy Project

Energy Technology Data Exchange (ETDEWEB)

Olah, George [Univ. of Southern California, Los Angeles, CA (United States); Prakash, G. K. [Univ. of Southern California, Los Angeles, CA (United States)

2014-02-01

The Methanol Economy Project is based on the concept of replacing fossil fuels with methanol generated either from renewable resources or abundant natural (shale) gas. The full methanol cycle was investigated in this project, from production of methanol through bromination of methane, bireforming of methane to syngas, CO₂ capture using supported amines, co-electrolysis of CO₂ and water to formate and syngas, decomposition of formate to CO₂ and H₂, and use of formic acid in a direct formic acid fuel cell. Each of these projects achieved milestones and provided new insights into their respective fields.

Quality standards and requirements for solid recovered fuels: a review.

Science.gov (United States)

Flamme, Sabine; Geiping, Julia

2012-04-01

The utilization of solid recovered fuels (SRF) for energy recovery has been increasing steadily in recent years, and this development is set to continue. In order to use SRF efficiently, it is necessary to define quality standards and introduce targeted quality assurance measures. SRF can be used both in mono-incineration and in co-incineration systems, for instance in power generation and cement plants; but as quality requirements differ, it is necessary to unambiguously define the term 'solid recovered fuel'. The purpose of this article is to provide an overview of the origin, development and the current status of quality assurance for SRF. The basic principles of quality assurance for SRF are explained with reference to the development of the German RAL Quality Assurance System and in addition specifications that have emerged from European standardization work of CEN/TC 343 are analysed.

Sustainable and safe energy supply with seawater uranium fueled HTGR and its economy

International Nuclear Information System (INIS)

Fukaya, Y.; Goto, M.

2017-01-01

Highlights: • We discussed uranium resources with an energy security perspective. • We concluded seawater uranium is preferable for sustainability and energy security. • We evaluated electricity generation cost of seawater uranium fueled HTGR. • We concluded electricity generation with seawater uranium is reasonable. - Abstract: Sustainable and safe energy supply with High Temperature Gas-cooled Reactor (HTGR) fueled by uranium from seawater have been investigated and discussed. From the view point of safety feature of self-regulation with thermal reactor of HTGR, the uranium resources should be inexhaustible. The seawater uranium is expected to be alternative resources to conventional resources because it exists so much in seawater as a solute. It is said that 4.5 billion tons of uranium is dissolved in the seawater, which corresponds to a consumption of approximately 72 thousand years. Moreover, a thousand times of the amount of 4.5 trillion tU of uranium, which corresponds to the consumption of 72 million years, also is included in the rock on the surface of the sea floor, and that is also recoverable as seawater uranium because uranium in seawater is in an equilibrium state with that. In other words, the uranium from seawater is almost inexhaustible natural resource. However, the recovery cost with current technology is still expensive compared with that of conventional uranium. Then, we assessed the effect of increase in uranium purchase cost on the entire electricity generation cost. In this study, the economy of electricity generation of cost of a commercial HTGR was evaluated with conventional uranium and seawater uranium. Compared with ordinary LWR using conventional uranium, HTGR can generate electricity cheaply because of small volume of simple direct gas turbine system compared with water and steam systems of LWR, rationalization by modularizing, and high thermal efficiency, even if fueled by seawater uranium. It is concluded that the HTGR

Collateral fluctuations in a monetary economy

NARCIS (Netherlands)

Ferraris, L.; Watanabe, M.

2011-01-01

This paper studies economy-wide fluctuations that occur endogenously in the presence of monetary and real assets. Using a standard monetary search model, we consider an economy in which agents can increase consumption, over and above what their liquid monetary asset holdings would allow, pledging

ORNL-GM: Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Qu, Jun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhou, Yan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Luo, Huimin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Toops, Todd J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brookshear, Daniel W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stump, Benjamin C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Viola, Michael B. [General Motors (GM) Technical Center, Pontiac, MI (United States); Zreik, Khaled [General Motors (GM) Technical Center, Pontiac, MI (United States); Ahmed, Tasfia [General Motors (GM) Technical Center, Pontiac, MI (United States)

2017-01-01

The overall objective of this project are as follows: Further develop ionic liquid (IL)-additized lowviscosity engine oils meeting the GF-5/6 specifications and possessing superior lubricating characteristics; Expand the IL additive technology to rear axle lubricants; and Seek a combined improvement in the vehicle fuel economy

System-of-Systems Framework for the Future Hydrogen-Based Transportation Economy: Preprint

Energy Technology Data Exchange (ETDEWEB)

Duffy, M.; Sandor, D.

2008-06-01

From a supply chain view, this paper traces the flow of transportation fuels through required systems and addresses the current petroleum-based economy, DOE's vision for a future hydrogen-based transportation economy, and the challenges of a massive market and infrastructure transformation.

Bus fuel consumption model

Energy Technology Data Exchange (ETDEWEB)

Zargari, S.A. [Iran Univ. of Science and Technology, Teheran (Iran, Islamic Republic of); Khan, A.M. [Carleton Univ., Ottawa, ON (Canada). Dept. of Civil and Environmental Engineering

2000-07-01

The interest in rapid bus transit has increased sharply with the realization that modern metropolitan areas rely on public transit to provide for strong economies and communities. As a prevention tool against traffic congestion, deteriorating air quality and rising greenhouse gas emissions, this study of bus fuel consumption was designed to assist in the planning and management of rapid bus transit. The Australian Road Research Board's (ARRB) Road Fuel Consumption Model was used as a starting point. The estimations required were realized with the help of Newtonian Mechanics. The four states of vehicular traffic were examined: acceleration, cruise, deceleration, and idle. The estimated total power required from the engine to overcome resistance forces, to run vehicle accessories and overcome internal engine friction was calculated. The data for the standard and articulated bus was obtained from OC Transpo in Ottawa. The study permitted the authors to conclude that the estimations for the parameters for power requirements and fuel consumption for heavy duty vehicles are appropriate. The methodology for the estimation of fuel consumption on the Transitway, which is part of the rapid bus transit system, proved adequate. In addition, the methodology was useful to estimate fuel savings resulting from demand management strategies with potential for modal shift. 9 refs., 6 tabs.

Fuels Performance | Transportation Research | NREL

Science.gov (United States)

chemistry, combustion, and emissions to answer two primary questions: How can improved fuel chemistry lead initiative Combustion and engines Fuel chemistry Emissions and fuel economy Find out about related NREL Chemistry. (2014) Saturated Monoglyceride Effects on Low-Temperature Performance of Biodiesel Blends. G.M

Trends and Issues in California's Low Carbon Fuel Standard - Learning from Response to Existing Climate Policy

Science.gov (United States)

Witcover, J.

2015-12-01

Debate over lower greenhouse gas (GHG) emissions from transportation has included heated discussion about appropriate policies and their cost and feasibility. One prominent policy mechanism, a carbon intensity standard, rates transport fuels based on analysis of lifecycle GHG emissions, and targets lower fuel pool carbon intensity through a market mechanism that uses a system of tradable, bankable credits and deficits. California instituted such a policy -- the Low Carbon Fuel Standard (LCFS) - in 2010, which targets a 10% carbon intensity (CI) reduction by 2020. The program rolled out amid concerns over slow development of new fuels expected to be very low carbon (such as cellulosic) and has faced court challenges that added considerable policy uncertainty. Since the program's start, state transport energy mix has shifted modestly but noticeably. Looking ahead, emerging issues for the program include amendments and re-adoption in response to a court ruling, potential interaction with California's multi-sector cap on carbon emissions (which started covering transport fuels in 2015), and impacts from similar CI standards in other jurisdictions. This study provides an analysis of fuel mix changes since the LCFS was implemented in 2011, and a discussion of emerging issues focusing on policy interaction. Descriptive statistics on alternative fuel use, available fuel pathways, and CI ratings are presented based on data from the California Air Resources Board (which runs the program). They document a shift towards more alternative fuels in a more diverse mix, with lower average CI ratings for most alternative fuel types. Financial incentives for various fuels are compared under the LCFS and the US federal Renewable Fuel Standard; disincentives from conceptually different carbon pricing schemes under the LCFS and the Cap-and-Trade are also outlined. The results provide important information on response to an existing market-based policy mechanism for addressing GHG

WWER-440 fuel cycles possibilities using improved fuel assemblies design

International Nuclear Information System (INIS)

Mikolas, P.; Svarny, J.

2008-01-01

Practically five years cycle has been achieved in the last years at NPP Dukovany. There are two principal means how it could be achieved. First, it is necessary to use fuel assemblies with higher fuel enrichment and second, to use fuel loading with very low leakage. Both these conditions are fulfilled at NPP Dukovany at this time. It is known, that the fuel cycle economy can be improved by increasing the fuel residence time in the core up to six years. There are at least two ways how this goal could be achieved. The simplest way is to increase enrichment in fuel. There exists a limit, which is 5.0 w % of 235 U. Taking into account some uncertainty, the calculation maximum is 4.95 w % of 235 U. The second way is to change fuel assembly design. There are several possibilities, which seem to be suitable from the neutron - physical point of view. The first one is higher mass content of uranium in a fuel assembly. The next possibility is to enlarge pin pitch. The last possibility is to 'omit' FA shroud. This is practically unrealistic; anyway, some other structural parts must be introduced. The basic neutron physical characteristics of these cycles for up-rated power are presented showing that the possibilities of fuel assemblies with this improved design in enlargement of fuel cycles are very promising. In the end, on the basis of neutron physical characteristics and necessary economical input parameters, a preliminary evaluation of economic contribution of proposals of advanced fuel assemblies on fuel cycle economy is presented (Authors)

Transmutation of minor actinide using BWR fueled mixed oxide

International Nuclear Information System (INIS)

Susilo, Jati

2000-01-01

Nuclear spent fuel recycle has a strategic importance in the aspect of nuclear fuel economy and prevention of its spread-out. One among other application of recycle is to produce mixed oxide fuel (Mo) namely mixed Plutonium and uranium oxide. As for decreasing the burden of nuclear high level waste (HLW) treatment, transmutation of minor actinide (MA) that has very long half life will be carried out by conversion technique in nuclear reactor. The purpose of this study was to know influence of transition fuel cell regarding the percent weight of transmutation MA in the BWR fueled MOX. Calculation of cell BWR was used SRAC computer code, with assume that the reactor in equilibrium. The percent weight of transmutation MA to be optimum by increasing the discharge burn-up of nuclear fuel, raising ratio of moderator to fuel volume (Vm/Vf), and loading MA with percent weight about 3%-6% and also reducing amount of percent weight Pu in MOX fuel. For mixed fuel standard reactor, reactivity value were obtained between about -50pcm ∼ -230pcm for void coefficient and -1.8pcm ∼ -2.6pcm for fuel temperature coefficient

Impacts of removing fuel import subsidies in Nigeria on poverty

International Nuclear Information System (INIS)

Siddig, Khalid; Aguiar, Angel; Grethe, Harald; Minor, Peter; Walmsley, Terrie

2014-01-01

The petroleum sector contributes substantially to the Nigerian economy; however, the potential benefits are diminished due to the existence of significant subsidies on imports of petroleum products. Subsidies on imported petroleum products are considered to be an important instrument for keeping fuel prices, and hence the cost of living, low. The costs of these subsidies, however, has risen dramatically in recent years due to increased volatility in world petroleum and petroleum product prices and increased illegal exportation of subsidized petroleum products into neighboring countries. Removing the subsidy on fuel is one of the most contentious socio-economic policy issues in Nigeria today. In this paper, an economy-wide framework is used to identify the impact of removing the fuel subsidy on the Nigerian economy and investigates how alternative policies might be used to meet socio-economic objectives related to fuel subsidies. The results show that while a reduction in the subsidy generally results in an increase in Nigerian GDP, it can have a detrimental impact on household income, and in particular on poor households. Accompanying the subsidy reduction with income transfers aimed at poor households or domestic production of petroleum products can alleviate the negative impacts on household income. - Highlights: • Subsidies on imported fuel compromise the contribution of crude oil in Nigeria. • Fuel subsidies benefit households, but harm the economy. • We use an economy-wide model to identify the impact of removing the fuel subsidy. • We simulate scenarios that target the poor and promote fuel's domestic production

77 FR 69924 - Request for Comments on a Renewal of a Previously Approved Information Collection: Production...

Science.gov (United States)

2012-11-21

... manufacturers' estimates of the future vehicle population, and fuel economy improvements and incremental costs...: Kenneth R. Katz, Fuel Economy Division, Office of International Policy, Fuel Economy and Consumer Programs... Parts 531 and 533 Passenger Car Average Fuel Economy Standards--Model Years 2016-2025; Light Truck...

Towards a carbon-negative sustainable bio-based economy.

Science.gov (United States)

Vanholme, Bartel; Desmet, Tom; Ronsse, Frederik; Rabaey, Korneel; Van Breusegem, Frank; De Mey, Marjan; Soetaert, Wim; Boerjan, Wout

2013-01-01

The bio-based economy relies on sustainable, plant-derived resources for fuels, chemicals, materials, food and feed rather than on the evanescent usage of fossil resources. The cornerstone of this economy is the biorefinery, in which renewable resources are intelligently converted to a plethora of products, maximizing the valorization of the feedstocks. Innovation is a prerequisite to move a fossil-based economy toward sustainable alternatives, and the viability of the bio-based economy depends on the integration between plant (green) and industrial (white) biotechnology. Green biotechnology deals with primary production through the improvement of biomass crops, while white biotechnology deals with the conversion of biomass into products and energy. Waste streams are minimized during these processes or partly converted to biogas, which can be used to power the processing pipeline. The sustainability of this economy is guaranteed by a third technology pillar that uses thermochemical conversion to valorize waste streams and fix residual carbon as biochar in the soil, hence creating a carbon-negative cycle. These three different multidisciplinary pillars interact through the value chain of the bio-based economy.

Towards a carbon-negative sustainable bio-based economy

Directory of Open Access Journals (Sweden)

Bartel eVanholme

2013-06-01

Full Text Available The bio-based economy relies on sustainable, plant-derived resources for fuels, chemicals, materials, food and feed rather than on the evanescent usage of fossil resources. The cornerstone of this economy is the biorefinery, in which renewable resources are intelligently converted to a plethora of products, maximizing the valorization of the feedstocks. Innovation is a prerequisite to move a fossil-based economy towards sustainable alternatives, and the viability of the bio-based economy depends on the integration between plant (green and industrial (white biotechnology. Green biotechnology deals with primary production through the improvement of biomass crops, while white biotechnology deals with the conversion of biomass into products and energy. Waste streams are minimized during these processes or partly converted to biogas, which can be used to power the processing pipeline. The sustainability of this economy is guaranteed by a third technology pillar that uses thermochemical conversion to valorize waste streams and fix residual carbon as biochar in the soil, hence creating a carbon-negative cycle. These three different multidisciplinary pillars interact through the value chain of the bio-based economy.

Towards a carbon-negative sustainable bio-based economy

Science.gov (United States)

Vanholme, Bartel; Desmet, Tom; Ronsse, Frederik; Rabaey, Korneel; Breusegem, Frank Van; Mey, Marjan De; Soetaert, Wim; Boerjan, Wout

2013-01-01

The bio-based economy relies on sustainable, plant-derived resources for fuels, chemicals, materials, food and feed rather than on the evanescent usage of fossil resources. The cornerstone of this economy is the biorefinery, in which renewable resources are intelligently converted to a plethora of products, maximizing the valorization of the feedstocks. Innovation is a prerequisite to move a fossil-based economy toward sustainable alternatives, and the viability of the bio-based economy depends on the integration between plant (green) and industrial (white) biotechnology. Green biotechnology deals with primary production through the improvement of biomass crops, while white biotechnology deals with the conversion of biomass into products and energy. Waste streams are minimized during these processes or partly converted to biogas, which can be used to power the processing pipeline. The sustainability of this economy is guaranteed by a third technology pillar that uses thermochemical conversion to valorize waste streams and fix residual carbon as biochar in the soil, hence creating a carbon-negative cycle. These three different multidisciplinary pillars interact through the value chain of the bio-based economy. PMID:23761802

Increased fuel burn-up and fuel cycle equilibrium

International Nuclear Information System (INIS)

Debes, M.

2001-01-01

Improvement of nuclear competitiveness will rely mainly on increased fuel performance, with higher burn-up, and reactors sustained life. Regarding spent fuel management, the EDF current policy relies on UO 2 fuel reprocessing (around 850 MTHM/year at La Hague) and MOX recycling to ensure plutonium flux adequacy (around 100 MTHM/year, with an electricity production equivalent to 30 TWh). This policy enables to reuse fuel material, while maintaining global kWh economy with existing facilities. It goes along with current perspective to increase fuel burn-up up to 57 GWday/t mean in 2010. The following presentation describes the consequences of higher fuel burn-up on fuel cycle and waste management and implementation of a long term and global equilibrium for decades in spent fuel management resulting from this strategy. (author)

Molybdenum-99-producing 37-element fuel bundle neutronically and thermal-hydraulically equivalent to a standard CANDU fuel bundle

Energy Technology Data Exchange (ETDEWEB)

Nichita, E., E-mail: Eleodor.Nichita@uoit.ca; Haroon, J., E-mail: Jawad.Haroon@uoit.ca

2016-10-15

Highlights: • A 37-element fuel bundle modified for {sup 99}Mo production in CANDU reactors is presented. • The modified bundle is neutronically and thermal-hydraulically equivalent to the standard bundle. • The modified bundle satisfies all safety criteria satisfied by the standard bundle. - Abstract: {sup 99m}Tc, the most commonly used radioisotope in diagnostic nuclear medicine, results from the radioactive decay of {sup 99}Mo which is currently being produced at various research reactors around the globe. In this study, the potential use of CANDU power reactors for the production of {sup 99}Mo is investigated. A modified 37-element fuel bundle, suitable for the production of {sup 99}Mo in existing CANDU-type reactors is proposed. The new bundle is specifically designed to be neutronically and thermal-hydraulically equivalent to the standard 37-element CANDU fuel bundle in normal, steady-state operation and, at the same time, be able to produce significant quantities of {sup 99}Mo when irradiated in a CANDU reactor. The proposed bundle design uses fuel pins consisting of a depleted-uranium centre surrounded by a thin layer of low-enriched uranium. The new molybdenum-producing bundle is analyzed using the lattice transport code DRAGON and the diffusion code DONJON. The proposed design is shown to produce 4081 six-day Curies of {sup 99}Mo activity per bundle when irradiated in the peak-power channel of a CANDU core, while maintaining the necessary reactivity and power rating limits. The calculated {sup 99}Mo yield corresponds to approximately one third of the world weekly demand. A production rate of ∼3 bundles per week can meet the global demand of {sup 99}Mo.

Can the Nigerian biofuel policy and incentives (2007) transform Nigeria into a biofuel economy?

International Nuclear Information System (INIS)

Ohimain, Elijah I.

2013-01-01

Nigeria's economy is largely dependent on petroleum, yet the country is suffering from fuel supply shortages. In response to the transportation fuel supply difficulties in Nigeria, the country released the Nigerian Biofuel Policy and Incentives in 2007 to create favorable investment climate for the entrance of Nigeria into the biofuel sector. The paper assessed the progress made thus far by Nigeria, 4 years after the Nigerian biofuel was released in an attempt to answer the question whether the policy is adequate to transform Nigeria into a biofuel economy. The study found that little progress has been made, which includes commencement of the construction of 20 bioethanol factories, installation of biofuel handling facilities at two depots (Mosimi and Atlas Cove), and selection of retail outlets for biofuel/conventional fuel mix. The site construction of the announced biofuel projects is now slow and other progress is marginal. We therefore conclude that the Nigerian biofuel policy is unlikely to transform Nigeria into a biofuel economy unless the Government revert and refocus on biofuel and include additional financial incentives such as grants and subsidy to complement the tax waivers (income, import duty, VAT), loans, and insurance cover contained in the policy. - Highlights: ► Nigeria's economy is dependent on petroleum, yet the country is suffering from fuel shortages. ► The Nigerian Biofuel Policy and Incentives was released in 2007. ► Little progress has been made since the policy was released 4 years ago. ► Hence, the policy is unlikely to transform Nigeria into a biofuel economy

China's growing methanol economy and its implications for energy and the environment

International Nuclear Information System (INIS)

Yang, Chi-Jen; Jackson, Robert B.

2012-01-01

For more than a decade, Nobel laureate George Olah and coworkers have advocated the Methanol Economy – replacing petroleum-based fuels and chemicals with methanol and methanol-derivatives – as a path to sustainable development. A first step to this vision appears to be occurring in China. In the past five years, China has quickly built an industry of coal-based methanol and dimethyl ether (DME) that is competitive in price with petroleum-based fuels. Methanol fuels offer many advantages, including a high octane rating and cleaner-burning properties than gasoline. Methanol also has some disadvantages. A coal-based Methanol Economy could enhance water shortages in China, increase net carbon dioxide emissions, and add volatility to regional and global coal prices. China's rapidly expanding Methanol Economy provides an interesting experiment for what could happen elsewhere if methanol is widely adopted, as proposed by Olah and researchers before him. - Highlights: ► China is quickly building a coal-based chemical industry. ► Methanol has become a significant automotive fuel and chemical feedstock in China. ► Coal-based methanol could provide a domestic alternative to imported oil. ► It, however, increases greenhouse gas emissions, and can cause other problems.

Thermal Expansion and Density Data of UO2 and Simulated Fuel for Standard Reference

International Nuclear Information System (INIS)

Yang, Jae Hwan; Na, S. H.; Lee, J. W.; Kang, K. H.

2010-01-01

Standard Reference Data (SRD) is the scientific, technical data whose reliability and accuracy are evaluated by scientist group. Since SRD has a great impact on the improvement of national competitiveness by stirring up technological innovation in every sector of industries, many countries are making great efforts on establishing SRD in various areas. Data center for nuclear fuel material in Korea Atomic Energy Research Institute plays a role to providing property data of nuclear fuel material at high temperature, pressure, and radiation which are essential for the safety evaluation of nuclear power. In this study, standardization of data on thermal expansion and density of UO 2 were carried out in the temperature range from 300 K to 3100 K via uncertainty evaluation of indirectly produced data. Besides, standardization of data on thermal expansion and density of simulated fuel were also done in the temperature range from 350 K to 1750 K via uncertainty evaluation of directly produced data

Challenges in Building a Sustainable Biobased Economy

DEFF Research Database (Denmark)

Mussatto, Solange I.

2017-01-01

for the production of fuels, chemicals, energy and materials is therefore recognized as a need by numerous industries and policy makers in countries around the world. In addition, a biobased economy has the potential to generate new jobs and even new industries, creating new opportunities for entrepreneurship...

A seismic analysis of Korean standard PWR fuels under transition core conditions

International Nuclear Information System (INIS)

Kim, Hyeong Koo; Park, Nam Kyu; Jang, Young Ki; Kim, Jae Ik; Kim, Kyu Tae

2005-01-01

The PLUS7 fuel is developed to achieve higher thermal performance, burnup and more safety margin than the conventional fuel used in the Korean Standard Nuclear Plants (KSNPs) and to sustain structural integrity under increased seismic requirement in Korea. In this study, a series of seismic analysis have been performed in order to evaluate the structural integrity of fuel assemblies associated with seismic loads in the KSNPs under transition core conditions replacing the Guardian fuel, which is a resident fuel in the KSNP reactors, with the PLUS7 fuel. For the analysis, transition core seismic models have been developed, based on the possible fuel loading patterns. And the maximum impact forces on the spacer grid and various stresses acting on the fuel components have been evaluated and compared with the through-grid strength of spacer grids and the stress criteria specified in the ASME code for each fuel component, respectively. Then three noticeable parameters regarding as important parameters governing fuel assembly dynamic behavior are evaluated to clarify their effects on the fuel impact and stress response. As a result of the study, it has been confirmed that both the PLUS7 and the Guardian fuel sustain their structural integrity under the transition core condition. And when the damping ratio is constant, increasing the natural frequency of fuel assembly results in a decrease in impact force. The fuel assembly flexural stiffness has an effect increasing the stress of fuel assembly, but not the impact force. And the spacer grid stiffness is directly related with the impact force response. (author)

The Greenlandic Economy – Structure and Prospects

DEFF Research Database (Denmark)

Andersen, Torben M.

an economic development which addresses current economic and social problems, makes the economy independent of transfers from outside, and provides for a satisfactory increase in living standards. Essential for this is a transformation such that the economy does not only rely on renewable natural resources...

Solid fuels. Coal. Economy and resources

International Nuclear Information System (INIS)

Bautin, F.; Martin-Amouroux, J.M.

2007-01-01

The share of coal in the world energy mix (25%) and its possible increase during the next decades is due to its specific use in steelmaking industry and to its excellent competitiveness in fossil-fuel power plants with respect to other energy sources. Its inferior energy efficiency is compensated by lower and more stable prices on international markets. This situation is explained by a strong competition and abundant reserves. However, coal is a strong emitter of greenhouse gases and would be temporarily penalized by the implementation of emission tax or trading systems before the development of carbon sequestration systems. This article presents: the main world markets (consumption per sector of activity, power generation market, coke market, start-up of a synthetic fuels market), the main international coal producers and traders (overview and typology, international trades, transport), the reserves and resources, and the worldwide perspectives (2050 scenarios, climatic risks, CO 2 prices and technological changes). (J.S.)

Circular economy and nuclear energy

International Nuclear Information System (INIS)

2017-01-01

This article first recalls what circular economy is, and its main principles (sustainable supply, eco-design, industrial and territorial ecology, economy of function rather than of possession, extension of product lifetime, recycling). It outlines its different benefits: improved resilience, inclusion of all actors of the territory, creation of local jobs, a global vision. In the next part, the nuclear industry is presented as a pioneer in this respect through various trends and developments: closure of the fuel cycle and saving of uranium and energy in the upstream part, reduction of wastes in the downstream part, exploitation of plants on a longer term, management of the production of conventional wastes, reduction of energy consumption, evolution of the doctrine in terms of management of very low level radioactive wastes

Standard examination stage for the fuels and materials examination facility

International Nuclear Information System (INIS)

Hess, J.W.; Frandsen, G.B.

1980-01-01

A Standard Examination Stage (SES) has been designed, fabricated, and tested for use in the Fuel and Materials Examination Facility (FMEF) at the Hanford Reservation near Richland, WA. The SES will perform multiple functions in a variety of nuclear fuel, absorber, and blanket pin handling, positioning, and examination operations in 11 of 22 work stations in the FMEF Nondestructive Examination (NDE) cell. Preprogrammable, automated, closed loop computer control provides precision positioning in the X, Y and Z directions and in pin rotational positioning. Modular construction of both the mechanical hardware and the electrical and control system has been used to facilitate in-cell maintainability

Non-standard constraints within In-Core Fuel Management

Energy Technology Data Exchange (ETDEWEB)

Maldonado, G.I. [University of Cincinnati, P.O. Box 210072, Cincinnati, OH 45221-0072 (United States); Torres, C. [Comision Federal de Electricidad, Gestion de Combustible, Mexico, D.F. (Mexico); Marrote, G.N.; Ruiz U, V. [Global Nuclear Fuel, Americas, LLC, PO Box 780, M/C A16, Wilmington, NC28402 (United States)]. e-mail: Ivan.Maldonado@uc.edu

2004-07-01

Recent advancements in the area of nuclear fuel management optimization have been considerable and widespread. Therefore, it is not surprising that the design of today's nuclear fuel reloads can be a highly automated process that is often accompanied by sophisticated optimization software and graphical user interfaces to assist core designers. Most typically, among other objectives, optimization software seeks to maximize the energy efficiency of a fuel cycle while satisfying a variety of safety, operational, and regulatory constraints. Concurrently, the general industry trend continues to be one of pursuing higher generating capacity (i.e., power up-rates) alongside cycle length extensions. As these increasingly invaluable software tools and ambitious performance goals are pursued in unison, more aggressive core designs ultimately emerge that effectively minimize the margins to limits and, in some cases, may turn out less forgiving or accommodating to changes in underlying key assumptions. The purpose of this article is to highlight a few 'non-standard', though common constraints that can affect a BWR core design but which are often difficult, if not impossible, to implement into an automated setting. In a way, this article indirectly emphasizes the unique and irreplaceable role of the experienced designer in light of 'real life' situations. (Author)

Non-standard constraints within In-Core Fuel Management

International Nuclear Information System (INIS)

Maldonado, G.I.; Torres, C.; Marrote, G.N.; Ruiz U, V.

2004-01-01

Recent advancements in the area of nuclear fuel management optimization have been considerable and widespread. Therefore, it is not surprising that the design of today's nuclear fuel reloads can be a highly automated process that is often accompanied by sophisticated optimization software and graphical user interfaces to assist core designers. Most typically, among other objectives, optimization software seeks to maximize the energy efficiency of a fuel cycle while satisfying a variety of safety, operational, and regulatory constraints. Concurrently, the general industry trend continues to be one of pursuing higher generating capacity (i.e., power up-rates) alongside cycle length extensions. As these increasingly invaluable software tools and ambitious performance goals are pursued in unison, more aggressive core designs ultimately emerge that effectively minimize the margins to limits and, in some cases, may turn out less forgiving or accommodating to changes in underlying key assumptions. The purpose of this article is to highlight a few 'non-standard', though common constraints that can affect a BWR core design but which are often difficult, if not impossible, to implement into an automated setting. In a way, this article indirectly emphasizes the unique and irreplaceable role of the experienced designer in light of 'real life' situations. (Author)

Preliminary investigations of a mixed standard-flip core for a TRIGA Mark II

International Nuclear Information System (INIS)

Ringle, John C.; Johnson, A.G.; Anderson, T.V.

1974-01-01

Several years ago it became apparent that due to our rapidly- increasing use rate, we would need a substantial amount of new fuel by late 1974 or early 1975. After investigations and discussions with GA, we decided that FLIP fuel would best meet our requirements for maximum fuel economy and high peak pulsing power. A proposal was submitted to the AEC for fuel assistance, and late in 1973 we were awarded a grant of $61,875. This will allow us to buy 3 FLIP-fueled-follower control rods, 1 instrumented FLIP fuel element, and 26 standard FLIP elements, giving us then a mixed core of approximately one-third FLIP and two-thirds standard elements. License amendments to accommodate this change are rather straightforward; modifications to the Technical Specifications will be somewhat more involved. The largest revisions which we envision are to our Safety Analysis Report. Although a few reactors have operated with a full FLIP core, and a few others have converted to mixed standard-FLIP cores, none of these has a standard Mark II core configuration. Those who have already converted to a mixed core have data and calculations which may be helpful to us, but the extent to which we can use these remains to be seen. The present status of our investigations into the analysis of a mixed standard-FLIP core will be presented. Any problems in calculational methods, finding appropriate data, modifications to Technical Specifications, etc., will be identified, and suggestions and help in these areas will be welcomed. (author)

Preliminary investigations of a mixed standard-flip core for a TRIGA Mark II

Energy Technology Data Exchange (ETDEWEB)

Ringle, John C; Johnson, A G; Anderson, T V [Oregon State University (United States)

1974-07-01

Several years ago it became apparent that due to our rapidly- increasing use rate, we would need a substantial amount of new fuel by late 1974 or early 1975. After investigations and discussions with GA, we decided that FLIP fuel would best meet our requirements for maximum fuel economy and high peak pulsing power. A proposal was submitted to the AEC for fuel assistance, and late in 1973 we were awarded a grant of $61,875. This will allow us to buy 3 FLIP-fueled-follower control rods, 1 instrumented FLIP fuel element, and 26 standard FLIP elements, giving us then a mixed core of approximately one-third FLIP and two-thirds standard elements. License amendments to accommodate this change are rather straightforward; modifications to the Technical Specifications will be somewhat more involved. The largest revisions which we envision are to our Safety Analysis Report. Although a few reactors have operated with a full FLIP core, and a few others have converted to mixed standard-FLIP cores, none of these has a standard Mark II core configuration. Those who have already converted to a mixed core have data and calculations which may be helpful to us, but the extent to which we can use these remains to be seen. The present status of our investigations into the analysis of a mixed standard-FLIP core will be presented. Any problems in calculational methods, finding appropriate data, modifications to Technical Specifications, etc., will be identified, and suggestions and help in these areas will be welcomed. (author)

Fuel assemblies

International Nuclear Information System (INIS)

Mukai, Hideyuki

1987-01-01

Purpose: To prevent bending of fuel rods caused by the difference of irradiation growth between coupling fuel rods and standards fuel rods thereby maintain the fuel rod integrity. Constitution: The f value for a fuel can (the ratio of pole of zirconium crystals in the entire crystals along the axial direction of the fuel can) of a coupling fuel rod secured by upper and lower tie plates is made smaller than the f value for the fuel can of a standard fuel rod not secured by the upper and the lower tie plates. This can make the irradiation growth of the fuel can of the coupling fuel rod greater than the irradiation growth of the fuel can of the standard fuel rod and, accordingly, since the elongation of the standard fuel rod can always by made greater, bending of the standard fuel rod can be prevented. (Yoshihara, M.)

Fueling the Gig Economy: A Case Study Evaluation of Upwork.com

OpenAIRE

Daryl D. Green; Craig Walker; Abdulrahman Alabulththim; Daniel Smith; Michele Phillips

2018-01-01

With recent downsizing of talented professionals and the power of globalization to provide opportunities for more underdeveloped countries, the gig economy is a source of influence in today’s generation of professionals. Online outsourcing media have shown to be valuable resources for companies who need a specific set of skills for a limited period. This case study evaluates Upwork.com, one of the leading freelance websites in the gig economy; this article provides insights on how others shou...

The series production in a standardized fabrication line for silicide fuels and commercial aspects

International Nuclear Information System (INIS)

Wehner, E.L.; Hassel, H.W.

1987-01-01

NUKEM has been responsible for the development and fabrication of LEU fuel elements for MTR reactors under the frame of the German AF program since 1979. The AF program is part of the international RERTR efforts, which were initiated by the INFCE Group in 1978. This paper describes the actual status of development and the transition from the prototype to the series production in a standardized manufacturing line for silicide fuels at NUKEM. Technical provisions and a customer oriented standardized product range aim at an economized manufacturing. (Author)

E85 and fuel efficiency: An empirical analysis of 2007 EPA test data

International Nuclear Information System (INIS)

Roberts, Matthew C.

2008-01-01

It is well known that ethanol has less energy per unit volume than gasoline. Differences in engine design and fuel characteristics affect the efficiency with which the chemical energy in gasoline and ethanol is converted into mechanical energy, so that the change in fuel economy may not be a linear function of energy content. This study analyzes the fuel economy tests performed by the US Environmental Protection Agency (EPA) on 2007 model year E85-compliant vehicles and finds that the difference in average fuel economy is not statistically different from the differential in energy content

Reference Material Properties and Standard Problems to Verify the Fuel Performance Models Ver 1.0

International Nuclear Information System (INIS)

Yang, Yong Sik; Kim, Jae Yong; Koo, Yang Hyun

2010-12-01

All fuel performance models must be validated by in-pile and out-pile tests. However, the model validation requires much efforts and times to confirm its exactness. In many fields, new performance models and codes are confirmed by code-to-code benchmarking process under simplified standard problem analysis. At present, the DUOS, which is the steady state fuel performance analysis code for dual cooled annular fuel, development project is progressing and new FEM module is developed to analyze the fuel performance during transient period. In addition, the verification process is planning to examine the new models and module's rightness by comparing with commercial finite element analysis such as a ADINA, ABAQUS and ANSYS. This reports contains the result of unification of material properties and establishment of standard problem to verify the newly developed models with commercial FEM code

Reviving the carbohydrate economy via multi-product lignocellulose biorefineries.

Science.gov (United States)

Zhang, Y-H Percival

2008-05-01

Before the industrial revolution, the global economy was largely based on living carbon from plants. Now the economy is mainly dependent on fossil fuels (dead carbon). Biomass is the only sustainable bioresource that can provide sufficient transportation fuels and renewable materials at the same time. Cellulosic ethanol production from less costly and most abundant lignocellulose is confronted with three main obstacles: (1) high processing costs (dollars /gallon of ethanol), (2) huge capital investment (dollars approximately 4-10/gallon of annual ethanol production capacity), and (3) a narrow margin between feedstock and product prices. Both lignocellulose fractionation technology and effective co-utilization of acetic acid, lignin and hemicellulose will be vital to the realization of profitable lignocellulose biorefineries, since co-product revenues would increase the margin up to 6.2-fold, where all purified lignocellulose co-components have higher selling prices (> approximately 1.0/kg) than ethanol ( approximately 0.5/kg of ethanol). Isolation of large amounts of lignocellulose components through lignocellulose fractionation would stimulate R&D in lignin and hemicellulose applications, as well as promote new markets for lignin- and hemicellulose-derivative products. Lignocellulose resource would be sufficient to replace significant fractionations (e.g., 30%) of transportation fuels through liquid biofuels, internal combustion engines in the short term, and would provide 100% transportation fuels by sugar-hydrogen-fuel cell systems in the long term.

Small Scale Gasification Application and Perspectives in Circular Economy

Science.gov (United States)

Klavins, Maris; Bisters, Valdis; Burlakovs, Juris

2018-06-01

Gasification is the process converting solid fuels as coal and organic plant matter, or biomass into combustible gas, called syngas. Gasification is a thermal conversion process using carbonaceous fuel, and it differs substantially from other thermal processes such as incineration or pyrolysis. The process can be used with virtually any carbonaceous fuel. It is an endothermic thermal conversion process, with partial oxidation being the dominant feature. Gasification converts various feedstock including waste to a syngas. Instead of producing only heat and electricity, synthesis gas produced by gasification may be transformed into commercial products with higher value as transport fuels, fertilizers, chemicals and even to substitute natural gas. Thermo-chemical conversion of biomass and solid municipal waste is developing as a tool to promote the idea of energy system without fossil fuels to a reality. In municipal solid waste management, gasification does not compete with recycling, moreover it enhances recycling programs. Pre-processing and after-processing must increase the amount of recyclables in the circular economy. Additionally, end of life plastics can serve as an energy feedstock for gasification as otherwise it cannot be sorted out and recycled. There is great potential for application of gasification technology within the biomass waste and solid waste management sector. Industrial self-consumption in the mode of combined heat and power can contribute to sustainable economic development within a circular economy.

Loop system for creating jet fuel vapor standards used in the calibration of infrared spectrophotometers and gas chromatographs.

Science.gov (United States)

Reboulet, James; Cunningham, Robert; Gunasekar, Palur G; Chapman, Gail D; Stevens, Sean C

2009-02-01

A whole body inhalation study of mixed jet fuel vapor and its aerosol necessitated the development of a method for preparing vapor only standards from the neat fuel. Jet fuel is a complex mixture of components which partitions between aerosol and vapor when aspirated based on relative volatility of the individual compounds. A method was desired which could separate the vapor portion from the aerosol component to prepare standards for the calibration of infrared spectrophotometers and a head space gas chromatography system. A re-circulating loop system was developed which provided vapor only standards whose composition matched those seen in an exposure system. Comparisons of nominal concentrations in the exposure system to those determined by infrared spectrophotometry were in 92-95% agreement. Comparison of jet fuel vapor concentrations determined by infrared spectrophotometry compared to head space gas chromatography yielded a 93% overall agreement in trial runs. These levels of agreement show the loop system to be a viable method for creating jet fuel vapor standards for calibrating instruments.

Summary of Preliminary Criticality Analysis for Peach Bottom Fuel in the DOE Standardized Spent Nuclear Fuel Canister

International Nuclear Information System (INIS)

Henrikson, D.J.

1999-01-01

The Department of Energy's (DOE's) National Spent Nuclear Fuel Program is developing a standardized set of canisters for DOE spent nuclear fuel (SNF). These canisters will be used for DOE SNF handling, interim storage, transportation, and disposal in the national repository. Several fuels are being examined in conjunction with the DOE SNF canisters. This report summarizes the preliminary criticality safety analysis that addresses general fissile loading limits for Peach Bottom graphite fuel in the DOE SNF canister. The canister is considered both alone and inside the 5-HLW/DOE Long Spent Fuel Co-disposal Waste Package, and in intact and degraded conditions. Results are appropriate for a single DOE SNF canister. Specific facilities, equipment, canister internal structures, and scenarios for handling, storage, and transportation have not yet been defined and are not evaluated in this analysis. The analysis assumes that the DOE SNF canister is designed so that it maintains reasonable geometric integrity. Parameters important to the results are the canister outer diameter, inner diameter, and wall thickness. These parameters are assumed to have nominal dimensions of 45.7-cm (18.0-in.), 43.815-cm (17.25-in), and 0.953-cm (0.375-in.), respectively. Based on the analysis results, the recommended fissile loading for the DOE SNF canister is 13 Peach Bottom fuel elements if no internal steel is present, and 15 Peach Bottom fuel elements if credit is taken for internal steel

Co-processing of standard gas oil and biocrude oil to hydrocarbon fuels

International Nuclear Information System (INIS)

Agblevor, Foster A.; Mante, O.; McClung, R.; Oyama, S.T.

2012-01-01

The major obstacle in thermochemical biomass conversion to hydrocarbon fuels using pyrolysis has been the high oxygen content and the poor stability of the product oils, which cause them to solidify during secondary processing. We have developed a fractional catalytic pyrolysis process to convert biomass feedstocks into a product termed “biocrude oils” (stable biomass pyrolysis oils) which are distinct from unstable conventional pyrolysis oils. The biocrude oils are stable, low viscosity liquids that are storable at ambient conditions without any significant increases in viscosity; distillable at both atmospheric pressure and under vacuum without char or solid formation. About 15 wt% biocrude oils containing 20–25% oxygen were blended with 85 wt% standard gas oil and co-cracked in an Advanced Catalyst Evaluation (ACE™) unit using fluid catalytic cracking (FCC) catalysts to produce hydrocarbon fuels that contain negligible amount of oxygen. For the same conversion of 70% for both the standard gas oil and the biocrude oil/gas oil blends, the product gasoline yield was 44 wt%, light cycle oil (LCO) 17 wt%, heavy cycle oil (HCO) 13 wt%, and liquefied petroleum gas (LPG) 16 wt%. However, the coke yield for the standard gas oil was 7.06 wt% compared to 6.64–6.81 wt% for the blends. There appeared to be hydrogen transfer from the cracking of the standard gas oil to the biocrude oil which subsequently eliminated the oxygen in the fuel without external hydrogen addition. We have demonstrated for the first time that biomass pyrolysis oils can be successfully converted into hydrocarbons without hydrogenation pretreatment. -- Highlights: ► The co-processed product had less than 1% oxygen content and contained biocarbons determined by 14 C analysis. ► The co-processing did not affect the yields of gasoline, LCO, and HCO. ► First demonstration of direct conversion of pyrolysis oils into drop-in hydrocarbon fuels.

Nuclides Economy

International Nuclear Information System (INIS)

Ivanov, Evgeny; Subbotin, Stanislav

2007-01-01

Traditionally the subject of discussion about the nuclear technology development is focused on the conditions that facilitate the nuclear power deployment. The main objective of this work is seeking of methodological basis for analysis of the coupling consequences of nuclear development. Nuclide economy is the term, which defines a new kind of society relations, dependent on nuclear technology development. It is rather closed to the setting of problems then to the solving of them. Last year Dr. Jonathan Tennenbaum published in Executive Intelligence Review Vol. 33 no 40 the article entitled as 'The Isotope Economy' where main interconnections for nuclear energy technologies and their infrastructure had been explained on the popular level. There he has given several answers and, therefore, just here we will try to expand this concept. We were interested by this publication because of similarity of our vision of resource base of technologies development. The main paradigm of 'Isotope economy' was expresses by Lyndon H. LaRouche: 'Instead of viewing the relevant resources of the planet as if they were a fixed totality, we must now assume responsibility of man's creating the new resources which will be more than adequate to sustain a growing world population at a constantly improved standard of physical per-capita output, and personal consumption'. We also consider the needed resources as a dynamic category. Nuclide economy and nuclide logistics both are needed for identifying of the future development of nuclear power as far we follow the holistic analysis approach 'from cave to grave'. Thus here we try to reasoning of decision making procedures and factors required for it in frame of innovative proposals development and deployment. The nuclear power development is needed in humanitarian scientific support with maximally deep consideration of all inter-disciplinary aspects of the nuclear power and nuclear technologies implementation. The main objectives for such

Plutonium economy. Plutonium-Wirtschaft

Energy Technology Data Exchange (ETDEWEB)

Traube, K

1984-01-01

The author expresses his opinion on the situation, describes the energy-economic setting, indicates the alternatives: fuel reprocessing or immediate long-term storage, and investigates the prospects for economic utilization of the breeder reactors. All the facts suggest that the breeder reactor will never be able to stand economic competition with light-water reactors. However, there is no way to prove the future. It is naive to think that every doubt could and must be removed before stopping the development of breeder reactors - and thus also the reprocessing of the fuel of light-water reactors. On the basis of the current state of knowledge an unbiased cost-benefit-analysis can only lead to the recommendation to stop construction immediately. But can 'experts', who for years or even decades have called for and supported the development of breeder reactors be expected to make an unbiased analysis. Klaus Traube strikes the balance of the state Germany's nuclear economy is in: although there is no chance of definitively abandoning that energy-political cul-de-sac, no new adventures must be embarked upon. Responsible handling of currently used nuclear technology means to give up breeder technology and waive plutonium economy. It is no supreme technology with the aid of which structural unemployment or any other economic problem could be solved.

Fuel cycles - a key to future CANDU success

International Nuclear Information System (INIS)

Kuran, S.; Hopwood, J.; Hastings, I.J.

2011-01-01

Globally, fuel cycles are being evaluated as ways of extending nuclear fuel resources, addressing security of supply and reducing back-end spent-fuel management. Current-technology thermal reactors and future fast reactors are the preferred platform for such fuel cycle applications and as an established thermal reactor with unique fuel-cycle capability, CANDU will play a key role in fulfilling such a vision. The next step in the evolution of CANDU fuel cycles will be the introduction of Recovered Uranium (RU), derived from conventional reprocessing. A low-risk RU option applicable in the short term comprises a combination of RU and Depleted Uranium (DU), both former waste streams, giving a Natural Uranium Equivalent (NUE) fuel. This option has been demonstrated in China, and all test bundles have been removed from the Qinshan 1 reactor. Additionally, work is being done on an NUE full core, a Thorium demonstration irradiation and an Advanced Fuel CANDU Reactor(AFCR). AECL is developing other fuel options for CANDU, including actinide waste burning. AECL has developed the Enhanced CANDU 6 (EC6) reactor, upgraded from its best-performing CANDU 6 design. High neutron economy, on-power refueling and a simple fuel bundle provide the EC6 with the flexibility to accommodate a range of advanced fuels, in addition to its standard natural uranium. (author)

Calculation of lifecycle greenhouse gas emissions for the renewable fuel standard

Science.gov (United States)

2009-06-25

The Energy Independence and Security Act of 2007 (EISA, P.L. 110-140), significantly expanded the renewable fuel standard (RFS) established in the Energy Policy Act of 2005 (EPAct 2005, P.L.109-58). The RFS requires the use of 9.0 billion gallons of ...

Minimization of actinide waste by multi-recycling of thoriated fuels in the EPR reactor

Directory of Open Access Journals (Sweden)

Nuttin A.

2012-02-01

Full Text Available The multi-recycling of innovative uranium/thorium oxide fuels for use in the European Pressurized water Reactor (EPR has been investigated. If increasing quantities of 238U, the fertile isotope in standard UO2 fuel, are replaced by 232Th, then a greater yield of new fissile material (233U is produced during the cycle than would otherwise be the case. This leads to economies of natural uranium of around 45% if the uranium in the spent fuel is multi-recycled. In addition we show that minor actinide and plutonium waste inventories are reduced and hence waste radio-toxicities and decay heats are up to a factor of 20 lower after 103 years. Two innovative fuel types named S90 and S20, ThO2 mixed with 90% and 20% enriched UO2 respectively, are compared as an alternative to standard uranium oxide (UOX and uranium/plutonium mixed oxide (MOX fuels at the longest EPR fuel discharge burn-ups of 65 GWd/t. Fissile and waste inventories are examined, waste radio-toxicities and decay heats are extracted and safety feedback coefficients are calculated.

Standard model for safety analysis report of fuel fabrication plants

International Nuclear Information System (INIS)

1980-09-01

A standard model for a safety analysis report of fuel fabrication plants is established. This model shows the presentation format, the origin, and the details of the minimal information required by CNEN (Comissao Nacional de Energia Nuclear) aiming to evaluate the requests of construction permits and operation licenses made according to the legislation in force. (E.G.) [pt

Standard model for safety analysis report of fuel reprocessing plants

International Nuclear Information System (INIS)

1979-12-01

A standard model for a safety analysis report of fuel reprocessing plants is established. This model shows the presentation format, the origin, and the details of the minimal information required by CNEN (Comissao Nacional de Energia Nuclear) aiming to evaluate the requests of construction permits and operation licenses made according to the legislation in force. (E.G.) [pt

PLATINUM, FUEL CELLS, AND FUTURE ROAD TRANSPORT

Science.gov (United States)

A vehicle powered by a fuel cell will emit virtually no air polution and, depending on fuel choice, can substantially improve fuel economy above that of current technology. Those attributes are complementary to issues of increasing national importance including the effects of tra...

A Model Predictive Control Approach for Fuel Economy Improvement of a Series Hydraulic Hybrid Vehicle

Directory of Open Access Journals (Sweden)

Tri-Vien Vu

2014-10-01

Full Text Available This study applied a model predictive control (MPC framework to solve the cruising control problem of a series hydraulic hybrid vehicle (SHHV. The controller not only regulates vehicle velocity, but also engine torque, engine speed, and accumulator pressure to their corresponding reference values. At each time step, a quadratic programming problem is solved within a predictive horizon to obtain the optimal control inputs. The objective is to minimize the output error. This approach ensures that the components operate at high efficiency thereby improving the total efficiency of the system. The proposed SHHV control system was evaluated under urban and highway driving conditions. By handling constraints and input-output interactions, the MPC-based control system ensures that the system operates safely and efficiently. The fuel economy of the proposed control scheme shows a noticeable improvement in comparison with the PID-based system, in which three Proportional-Integral-Derivative (PID controllers are used for cruising control.

FY2014 Fuel & Lubricant Technologies Annual Progress Report

Energy Technology Data Exchange (ETDEWEB)

Stork, Kevin [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

2016-02-01

Annual progress report for Fuel & Lubricant Technologies. The Fuel & Lubricant Technologies Program supports fuels and lubricants research and development (R&D) to provide vehicle manufacturers and users with cost-competitive options that enable high fuel economy with low emissions, and contribute to petroleum displacement.

The Brazilian strategy for the hydrogen economy; A estrategia brasileira para economia do hidrogenio

Energy Technology Data Exchange (ETDEWEB)

Matos, Maiana Brito de [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica; Neves Junior, Newton Pimenta

2008-07-01

This paper examines the Brazilian strategy in the development of technology related to hydrogen and the fuel cell systems. The Brazilian program and road map in the area are analyzed: the Program on Science, Technology and Innovation for the Hydrogen Economy - Pro H2, former Brazilian Program of the Fuel Cell Systems-ProCaC which was created in 2002 by the Ministry of Science, Technology - MCT, and the Road map for Structuring of the Hydrogen Economy in Brazil, which was created in 2004 by the Ministry of Mines and Energy - MME. (author)

THE NEW ECONOMY AND THE ECONOMY OF TOURISM

Directory of Open Access Journals (Sweden)

MIRELA MAZILU

2011-01-01

Full Text Available Together with the Internet, e-business and the new economy era, in general, fundamental transformation of the social and economic structure take place. In parallel, the assaults on the standard economic science amplify, in the sense of some conceptual reformulations and of some reinterpretations of the economic phenomena and laws. Besides the classical factors of production, work and capital, information is added, either as a distinct factor or as a detached one of the two mentioned. Also, the empiric findings regarding the so-called tertiarisation of the economy or the increase of the share of the services sector in the total of the national economy, as well as the so-called intangible investments in the total of the investment funds, have lead to numerous attempts of redefining what we call today a "modern economy". Other factors with major influence, regarding the adjustment of the economic science to the new trends from the real economy, refer to the following: the liberalisation of the international exchanges and the globalisation; the growth of the importance of the so-called free time (including here the household activities and the ones unfolded in the interest of the community, entertainment, but also the time destined to the development of the degree of culture and education on one's own and the fluidisation of the limits of differentiation between this and the work activity in the formal sector as well as the informal one; the more rapid dynamic of the financial and banking markets than the so-called classic productive sector of the economy; the extension of the use of computers and of the means and techniques of communication, in the activity of the companies as well as in the households, and the impact on the structure of the time and the financial budget of the population etc. All these have an impact on the tourism unfolding.

A nuclear based hydrogen economy

International Nuclear Information System (INIS)

Sandquist, G.M.; Tamm, G.; Kunze, J.

2005-01-01

Exhausting demands are being imposed upon the world's ability to extract and deliver oil to the nations demanding fluid fossil fuels. This paper analyzes these issues and concludes that there must be no delay in beginning the development of the 'hydrogen economy' using nuclear energy as the primary energy source to provide both the fluid fuel and electrical power required in the 21st century. Nuclear energy is the only proven technology that is abundant and available worldwide to provide the primary energy needed to produce adequate hydrogen fluid fuel supplies to replace oil. Most importantly, this energy transition can be accomplished in an economical and technically proven manner while lowering greenhouse gas emissions. Furthermore, a similar application of using wind and solar to produce hydrogen instead of electricity for the grid can pave the way for the much larger production scales of nuclear plants producing both electricity and hydrogen. (authors)

Environmental implications of alternative-fueled automobiles: Air quality and greenhouse gas tradeoffs

International Nuclear Information System (INIS)

MaClean, H.L.; Lave, L.B.

2000-01-01

The authors analyze alternative fuel-powerstrain options for internal combustion engine automobiles. Fuel/engine efficiency, energy use, pollutant discharges, and greenhouse gas emissions are estimated for spark and compression ignited, direct injected (DI), and indirect injected (II) engines fueled by conventional and reformulated gasoline, reformulated diesel, compressed natural gas (CNG), and alcohols. Since comparisons of fuels and technologies in dissimilar vehicles are misleading, the authors hold emissions level, range, vehicle size class, and style constant. At present, CNG vehicles have the best exhaust emissions performance while DI diesels have the worst. Compared to a conventional gasoline fueled II automobile, greenhouse gases could be reduced by 40% by a DI CNG automobile and by 25% by a DI diesel. Gasoline- and diesel-fueled automobiles are able to attain long ranges with little weight or fuel economy penalty. CNG vehicles have the highest penalty for increasing range, due to their heavy fuel storage systems, but are the most attractive for a 160-km range. DI engines, particularly diesels, may not be able to meet strict emissions standards, at least not without lowering efficiency

49 CFR 571.303 - Standard No. 303; Fuel system integrity of compressed natural gas vehicles.

Science.gov (United States)

2010-10-01

... compressed natural gas vehicles. 571.303 Section 571.303 Transportation Other Regulations Relating to... system integrity of compressed natural gas vehicles. S1. Scope. This standard specifies requirements for the integrity of motor vehicle fuel systems using compressed natural gas (CNG), including the CNG fuel...

Physical characterization of biomass-based pyrolysis liquids. Application of standard fuel oil analyses

Energy Technology Data Exchange (ETDEWEB)

Oasmaa, A; Leppaemaeki, E; Koponen, P; Levander, J; Tapola, E [VTT Energy, Espoo (Finland). Energy Production Technologies

1998-12-31

The main purpose of the study was to test the applicability of standard fuel oil methods developed for petroleum-based fuels to pyrolysis liquids. In addition, research on sampling, homogeneity, stability, miscibility and corrosivity was carried out. The standard methods have been tested for several different pyrolysis liquids. Recommendations on sampling, sample size and small modifications of standard methods are presented. In general, most of the methods can be used as such but the accuracy of the analysis can be improved by minor modifications. Fuel oil analyses not suitable for pyrolysis liquids have been identified. Homogeneity of the liquids is the most critical factor in accurate analysis. The presence of air bubbles may disturb in several analyses. Sample preheating and prefiltration should be avoided when possible. The former may cause changes in the composition and structure of the pyrolysis liquid. The latter may remove part of organic material with particles. The size of the sample should be determined on the basis of the homogeneity and the water content of the liquid. The basic analyses of the Technical Research Centre of Finland (VTT) include water, pH, solids, ash, Conradson carbon residue, heating value, CHN, density, viscosity, pourpoint, flash point, and stability. Additional analyses are carried out when needed. (orig.) 53 refs.

Fuel spacer

International Nuclear Information System (INIS)

Nishida, Koji; Yokomizo, Osamu; Kanazawa, Toru; Kashiwai, Shin-ichi; Orii, Akihito.

1992-01-01

The present invention concerns a fuel spacer for a fuel assembly of a BWR type reactor and a PTR type reactor. Springs each having a vane are disposed on the side surface of a circular cell which supports a fuel rods. A vortex streams having a vertical component are formed by the vanes in the flowing direction of a flowing channel between adjacent cylindrical cells. Liquid droplets carried by streams are deposited on liquid membrane streams flowing along the fuel rod at the downstream of the spacer by the vortex streams. In view of the above, the liquid droplets can be deposited to the fuel rod without increasing the amount of metal of the spacer. Accordingly, the thermal margin of the fuel assembly can be improved without losing neutron economy. (I.N.)

Hydrogen: Its Future Role in the Nation's Energy Economy.

Science.gov (United States)

Winsche, W E; Hoffman, K C; Salzano, F J

1973-06-29

In examining the potential role of hydrogen in the energy economy of the future, we take an optimistic view. All the technology required for implementation is feasible but a great deal of development and refinement is necessary. A pessimistic approach would obviously discourage further thinking about an important and perhaps the most reasonable alternative for the future. We have considered a limited number of alternative energy systems involving hydrogen and have shown that hydrogen could be a viable secondary source of energy derived from nuclear power; for the immediate future, hydrogen could be derived from coal. A hydrogen supply system could have greater flexibility and be competitive with a more conventional all-electric delivery system. Technological improvements could make hydrogen as an energy source an economic reality. The systems examined in this article show how hydrogen can serve as a general-purpose fuel for residential and automotive applications. Aside from being a source of heat and motive power, hydrogen could also supply the electrical needs of the household via fuel cells (19), turbines, or conventional "total energy systems." The total cost of energy to a residence supplied with hydrogen fuel depends on the ratio of the requirements for direct fuel use to the requirements for electrical use. A greater direct use of hydrogen as a fuel without conversion to electricity reduces the overall cost of energy supplied to the household because of the greater expense of electrical transmission and distribution. Hydrogen fuel is especially attractive for use in domestic residential applications where the bulk of the energy requirement is for thermal energy. Although a considerable amount of research is required before any hydrogen energy delivery system can be implemented, the necessary developments are within the capability of present-day technology and the system could be made attractive economically .Techniques for producing hydrogen from water by

Role of Engine and Driveline Lubricants in Fuel Efficiency - Summary Report

Energy Technology Data Exchange (ETDEWEB)

Bansal, Jai G. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Fenske, George [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Adkins, Mark [AK Collaborations, Phoenix, AZ (United States)

2017-09-30

A virtual workshop was held on May 10, 2017, to obtain input from stakeholders on the role that lubricants can contribute to improving the fuel economy of on-road vehicles – with a focus on legacy vehicles. A ThinkTank collaboration tool was used to facilitate collection and real-time analysis of input provided by the participants. Input was in the form of numeric responses on the amount of fuel economy gains that the respondents felt are possible for light duty (LD) and heavy duty (HD) vehicles, the sources of the gains, and the barriers that will need to be addressed to achieve the fuel economy (FE) gains.

Fuel assembly

International Nuclear Information System (INIS)

Sakuyama, Tadashi; Mukai, Hideyuki.

1988-01-01

Purpose: To prevent the bending of a fuel rod caused by the difference in the elongation between a joined fuel rod and a standard fuel rod thereby maintain the fuel rod integrity. Constitution: A joined fuel rod is in a thread engagement at its lower end plug thereof with a lower plate, while passed through at its upper end plug into an upper tie plate and secured with a nut. Further, a standard fuel rod is engaged at its upper end plug and lower end plug with the upper tie plate and the lower tie plate respectively. Expansion springs are mounted to the upper end plugs of these bonded fuel rods and the standard fuel rods for preventing this lifting. Each of the fuel rods comprises a plurality of sintered pellets of nuclear fuel materials laminated in a zircaloy fuel can. The content of the alloy ingredient in the fuel can of the bonded fuel rod is made greater than that of the alloy ingredient of the standard fuel rod. this can increase the elongation for the bonded fuel rod, and the spring of the standard fuel rod is tightly bonded to prevent the bending. (Yoshino, Y.)

Review of application code and standards for mechanical and piping design of HANARO fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Kim, J. Y.

1998-02-01

The design and installation of the irradiation test facility for verification test of the fuel performance are very important in connection with maximization of the utilization of HANARO. HANARO fuel test loop was designed in accordance with the same code and standards of nuclear power plant because HANARO FTL will be operated the high pressure and temperature same as nuclear power plant operation conditions. The objective of this study is to confirm the propriety of application code and standards for mechanical and piping of HANARO fuel test loop and to decide the technical specification of FTL systems. (author). 18 refs., 8 tabs., 6 figs.

Can the social market economy be a viable solution for a future sustainable development of the Romanian economy?

Directory of Open Access Journals (Sweden)

Strat Vasile Alecsandru

2017-07-01

Full Text Available Social market economy (SME is a socio-economic model which attempts to unite the freedom of a competitive market economy with social equilibrium and progress. It is seen as a “third path” besides a purely liberal market economy and an economy which is heavily regulated by the state – in the SME there is an intermediate degree of regulation. Historically, the model corresponds to the real economic policy of the German Federal Republic after the 1950s, thus it is sometimes called Rhine capitalism. According to the Treaty of Lisbon from 2007, the European Union pursues a competitive social market economy with full employment and social progress. On one hand, this model wishes to exploit the advantages of a free market economy, especially its high efficiency in the production of goods, while on the other hand it uses state intervention to correct for potential negative outcomes from market processes. Further characteristics of this model are: ensuring competition, free price formation, private property, motivating performance through profit aspirations as well as guarding personal freedoms. Last but not least, this model encompasses a strong structural policy by encouraging weaker geographical regions or industries. Therefore, it is highly probable that such a socio-economic model might be the appropriate alternative to fuel a sustainable growth of the Romanian economy. Using county level data, from the National Institute of Statistics and from the National Office of the Trade Register, for the year 2015 we show that the Romanian economy is highly polarized with a few growth poles (islands and a large number of underdeveloped units. Thus, it becomes obvious that these important disparities will hinder a future sustainable development and by consequence a clear “road-map” represented by this economic model might prove to be a viable solution for the Romanian economy.

Research of natural resources saving by design studies of Pressurized Light Water Reactors and High Conversion PWR cores with mixed oxide fuels composed of thorium/uranium/plutonium

International Nuclear Information System (INIS)

Vallet, V.

2012-01-01

Within the framework of innovative neutronic conception of Pressurized Light Water Reactors (PWR) of 3. generation, saving of natural resources is of paramount importance for sustainable nuclear energy production. This study consists in the one hand to design high Conversion Reactors exploiting mixed oxide fuels composed of thorium/uranium/plutonium, and in the other hand, to elaborate multi-recycling strategies of both plutonium and 233 U, in order to maximize natural resources economy. This study has two main objectives: first the design of High Conversion PWR (HCPWR) with mixed oxide fuels composed of thorium/uranium/plutonium, and secondly the setting up of multi-recycling strategies of both plutonium and 233 U, to better natural resources economy. The approach took place in four stages. Two ways of introducing thorium into PWR have been identified: the first is with low moderator to fuel volume ratios (MR) and ThPuO 2 fuel, and the second is with standard or high MR and ThUO 2 fuel. The first way led to the design of under-moderated HCPWR following the criteria of high 233 U production and low plutonium consumption. This second step came up with two specific concepts, from which multi-recycling strategies have been elaborated. The exclusive production and recycling of 233 U inside HCPWR limits the annual economy of natural uranium to approximately 30%. It was brought to light that the strong need in plutonium in the HCPWR dedicated to 233 U production is the limiting factor. That is why it was eventually proposed to study how the production of 233 U within PWR (with standard MR), from 2020. It was shown that the anticipated production of 233 U in dedicated PWR relaxes the constraint on plutonium inventories and favours the transition toward a symbiotic reactor fleet composed of both PWR and HCPWR loaded with thorium fuel. This strategy is more adapted and leads to an annual economy of natural uranium of about 65%. (author) [fr

Radiation processing and market economy

International Nuclear Information System (INIS)

Zagorski, Z.P.

1998-01-01

In the system of totalitarian economy, regulated by bureaucracy, the real value of equipment, materials and services is almost completely unknown, what makes impossible the comparison of different technologies, eliminates competition, disturbs research and development. With introduction of market economy in Central and Eastern Europe, the radiation processing has lost doubtful support, becoming an independent business, subject to laws of free market economy. Only the most valuable objects of processing have survived that test. At the top of the list are: radiation sterilization of medical equipment and radiation induced crosslinking of polymers, polyethylene in particular. New elements of competition has entered the scene, as well as questions of international regulations and standards have appeared

Road transport fuels in europe: the explosion of demand for diesel fuel

International Nuclear Information System (INIS)

Bensaid, B.

2004-01-01

In the last 20 years, road transport fuel consumption has more than doubled in European countries, due to strong growth on the diesel passenger car segment and in the transport of road freight. In an economy heavily dependent on oil, European authorities are seeking to promote alternative energy solutions, such as motor fuels produced from biomass

Establishment of an authenticated physical standard for gamma spectrometric determination of the U-235 content of MTR fuel and evaluation of measurement procedures

International Nuclear Information System (INIS)

Fleck, C.M.

1979-12-01

Measurements of U-235 content in a standard MTR fuel element were carried out, using scintillation and semi-conductor spectrometers. Three different types of measurement were carried out: a) Comparison of different primary standards among one another and with single fuel plates. b) Calibration of the MTR fuel element as an authenticated physical standard. c) Evaluation of over all errors in assay measurements on MTR fuel elements. The error of the whole assay measurement will be approximately 0.9%. The Uranium distribution in the single fuel plates is the original source of error. In the case of equal Uranium contents in all fuel plates of one fuel assembly, the error of assay measurements would be about 0.3% relative to the primary standards

Development and Validation of A Nuclear Fuel Cycle Analysis Tool: A FUTURE Code

Energy Technology Data Exchange (ETDEWEB)

Kim, S. K.; Ko, W. I. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Yoon Hee [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2013-10-15

This paper presents the development and validation methods of the FUTURE (FUel cycle analysis Tool for nUcleaR Energy) code, which was developed for a dynamic material flow evaluation and economic analysis of the nuclear fuel cycle. This code enables an evaluation of a nuclear material flow and its economy for diverse nuclear fuel cycles based on a predictable scenario. The most notable virtue of this FUTURE code, which was developed using C and MICROSOFT SQL DBMS, is that a program user can design a nuclear fuel cycle process easily using a standard process on the canvas screen through a drag-and-drop method. From the user's point of view, this code is very easy to use thanks to its high flexibility. In addition, the new code also enables the maintenance of data integrity by constructing a database environment of the results of the nuclear fuel cycle analyses.

Thorium-Based Fuels Preliminary Lattice Cell Studies for Candu Reactors

International Nuclear Information System (INIS)

Margeanu, C.A.; Rizoiu, A.C.

2009-01-01

The choice of nuclear power as a major contributor to the future global energy needs must take into account acceptable risks of nuclear weapon proliferation, in addition to economic competitiveness, acceptable safety standards, and acceptable waste disposal options. Candu reactors offer a proven technology, safe and reliable reactor technology, with an interesting evolutionary potential for proliferation resistance, their versatility for various fuel cycles creating premises for a better utilization of global fuel resources. Candu reactors impressive degree of fuel cycle flexibility is a consequence of its channel design, excellent neutron economy, on-power refueling, and simple fuel bundle. These features facilitate the introduction and exploitation of various fuel cycles in Candu reactors in an evolutionary fashion. The main reasons for our interest in Thorium-based fuel cycles have been, globally, to extend the energy obtainable from natural Uranium and, locally, to provide a greater degree of energy self-reliance. Applying the once through Thorium (OTT) cycle in existing and advanced Candu reactors might be seen as an evaluative concept for the sustainable development both from the economic and waste management points of view. Two Candu fuel bundles project will be used for the proposed analysis, namely the Candu standard fuel bundle with 37 fuel elements and the CANFLEX fuel bundle with 43 fuel elements. Using the Canadian proposed scheme - loading mixed ThO 2 -SEU CANFLEX bundles in Candu 6 reactors - simulated at lattice cell level led to promising conclusions on operation at higher fuel burnups, reduction of the fissile content to the end of the cycle, minor actinide content reduction in the spent fuel, reduction of the spent fuel radiotoxicity, presence of radionuclides emitting strong gamma radiation for proliferation resistance benefit. The calculations were performed using the lattice codes WIMS and Dragon (together with the corresponding nuclear data

Standard casks for the transport of LWR spent fuel

International Nuclear Information System (INIS)

Blum, P.

1986-01-01

During the past decade, TRANSNUCLEAIRE has developed, licensed and marketed a family of standard casks for the transport of spent fuel from LWR reactors to reprocessing plants and the ancillary equipments necessary for their operation and transport. A large number of these casks have been manufactured in different countries and are presently used for european and intercontinental transports. The main advantages of these casks are: large payload, moderate cost, reliability, standardisation facilitating fabrication, operation and spare part supply [fr

Reducing Fuel Volatility. An Additional Benefit From Blending Bio-fuels?

Energy Technology Data Exchange (ETDEWEB)

Bailis, R. [Yale School of Forestry and Environmental Studies, 195 Prospect Street, New Haven, CT 06511 (United States); Koebl, B.S. [Utrecht University, Science Technology and Society, Budapestlaan 6, 3584 CD Utrecht (Netherlands); Sanders, M. [Utrecht University, Utrecht School of Economics, Janskerkhof 12, 3512 BL Utrecht (Netherlands)

2011-02-15

Oil price volatility harms economic growth. Diversifying into different fuel types can mitigate this effect by reducing volatility in fuel prices. Producing bio-fuels may thus have additional benefits in terms of avoided damage to macro-economic growth. In this study we investigate trends and patterns in the determinants of a volatility gain in order to provide an estimate of the tendency and the size of the volatility gain in the future. The accumulated avoided loss from blending gasoline with 20 percent ethanol-fuel estimated for the US economy amounts to 795 bn. USD between 2010 and 2019 with growing tendency. An amount that should be considered in cost-benefit analysis of bio-fuels.

Fuel assembly

International Nuclear Information System (INIS)

Chaki, Masao; Nishida, Koji; Karasawa, Hidetoshi; Kanazawa, Toru; Orii, Akihito; Nagayoshi, Takuji; Kashiwai, Shin-ichi; Masuhara, Yasuhiro

1998-01-01

The present invention concerns a fuel assembly, for a BWR type nuclear reactor, comprising fuel rods in 9 x 9 matrix. The inner width of the channel box is about 132mm and the length of the fuel rods which are not short fuel rods is about 4m. Two water rods having a circular cross section are arranged on a diagonal line in a portion of 3 x 3 matrix at the center of the fuel assembly, and two fuel rods are disposed at vacant spaces, and the number of fuel rods is 74. Eight fuel rods are determined as short fuel rods among 74 fuel rods. Assuming the fuel inventory in the short fuel rod as X(kg), and the fuel inventory in the fuel rods other than the short fuel rods as Y(kg), X and Y satisfy the relation: X + Y ≥ 173m, Y ≤ - 9.7X + 292, Y ≤ - 0.3X + 203 and X > 0. Then, even when the short fuel rods are used, the fuel inventory is increased and fuel economy can be improved. (I.N.)

Future fuels for the asia-pacific region

International Nuclear Information System (INIS)

Tegart, G.

2006-01-01

The debate about climate change, the role of greenhouse gas emissions and the need for reduction of fossil fuel consumption has largely been between developed economies. The rapidly growing economic activities of China and India and other Asian and South American economies have not been factored into the debate. Many of these economies are members of the Asia Pacific Economic Cooperation, a grouping of 21 economies around the Pacific Rim, which has been concerned, among other issues such as trade liberalisation and economic cooperation, about the future energy needs of economies in the region

Energy sustainability performance of the regional economy

Directory of Open Access Journals (Sweden)

N. I. Danilov

2005-03-01

Full Text Available The results of the study of the dynamics of energy intensity of gross regional product of the Sverdlovsk region for the period 1996 - 2003 years. and projections for the period up to 2015. The principal possibility of growth performance of the regional economy, without a significant increase in the consumption of primary fuel.

Enhanced CANDU6: Reactor and fuel cycle options - Natural uranium and beyond

International Nuclear Information System (INIS)

Ovanes, M.; Chan, P. S. W.; Mao, J.; Alderson, N.; Hopwood, J. M.

2012-01-01

The Enhanced CANDU 6 R (ECo R ) is the updated version of the well established CANDU 6 family of units incorporating improved safety characteristics designed to meet or exceed Generation III nuclear power plant expectations. The EC6 retains the excellent neutron economy and fuel cycle flexibility that are inherent in the CANDU reactor design. The reference design is based on natural uranium fuel, but the EC6 is also able to utilize additional fuel options, including the use of Recovered Uranium (RU) and Thorium based fuels, without requiring major hardware upgrades to the existing control and safety systems. This paper outlines the major changes in the EC6 core design from the existing C6 design that significantly enhance the safety characteristics and operating efficiency of the reactor. The use of RU fuel as a transparent replacement fuel for the standard 37-el NU fuel, and several RU based advanced fuel designs that give significant improvements in fuel burnup and inherent safety characteristics are also discussed in the paper. In addition, the suitability of the EC6 to use MOX and related Pu-based fuels will also be discussed. (authors)

Standard recommended practice for examination of fuel element cladding including the determination of the mechanical properties

International Nuclear Information System (INIS)

Anon.

1975-01-01

Guidelines are provided for the post-irradiation examination of fuel cladding and to achieve better correlation and interpretation of the data in the field of radiation effects. The recommended practice is applicable to metal cladding of all types of fuel elements. The tests cited are suitable for determining mechanical properties of the fuel elements cladding. Various ASTM standards and test methods are cited

Fuel Economy and Emissions Effects of Low Tire Pressure, Open Windows, Roof Top and Hitch-Mounted Cargo, and Trailer

Energy Technology Data Exchange (ETDEWEB)

Thomas, John F [ORNL; Huff, Shean P [ORNL; West, Brian H [ORNL

2014-01-01

To quantify the fuel economy (FE) effect of some common vehicle accessories or alterations, a compact passenger sedan and a sport utility vehicle (SUV) were subjected to SAE J2263 coastdown procedures. Coastdowns were conducted with low tire pressure, all windows open, with a roof top or hitch-mounted cargo carrier, and with the SUV pulling an enclosed cargo trailer. From these coastdowns, vehicle dynamometer coefficients were developed which enabled the execution of vehicle dynamometer experiments to determine the effect of these changes on vehicle FE and emissions over standard drive cycles and at steady highway speeds. The FE penalty associated with the rooftop cargo box mounted on the compact sedan was as high as 25-27% at higher speeds, where the aerodynamic drag is most pronounced. For both vehicles, use of a hitch mounted cargo tray carrying a similar load resulted in very small FE penalties, unlike the rooftop cargo box. The results for the SUV pulling a 3500 pound enclosed cargo trailer were rather dramatic, resulting in FE penalties ranging from 30%, for the city cycle, to 50% at 80 mph, at which point significant CO generation indicated protective enrichment due to high load. Low tire pressure cases resulted in negligible to 10% FE penalty depending on the specific case and test point. Driving with all four windows open decreased FE by 4-8.5% for the compact sedan, and 1-4% for the SUV.

77 FR 13009 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

Science.gov (United States)

2012-03-05

... Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel Pathways Under the Renewable Fuel Standard Program AGENCY: Environmental Protection Agency (EPA). ACTION: Withdrawal... Renewable Fuel Standard program regulations. Because EPA received adverse comment, we are withdrawing the...

Modeling and Parameterization of Fuel Economy in Heavy Duty Vehicles (HDVs

Directory of Open Access Journals (Sweden)

Yunjung Oh

2014-08-01

Full Text Available The present paper suggests fuel consumption modeling for HDVs based on the code from the Japanese Ministry of the Environment. Two interpolation models (inversed distance weighted (IDW and Hermite and three types of fuel efficiency maps (coarse, medium, and dense were adopted to determine the most appropriate combination for further studies. Finally, sensitivity analysis studies were conducted to determine which parameters greatly impact the fuel efficiency prediction results for HDVs. While vitiating each parameter at specific percentages (±1%, ±3%, ±5%, ±10%, the change rate of the fuel efficiency results was analyzed, and the main factors affecting fuel efficiency were summarized. As a result, the Japanese transformation algorithm program showed good agreement with slightly increased prediction accuracy for the fuel efficiency test results when applying the Hermite interpolation method compared to IDW interpolation. The prediction accuracy of fuel efficiency remained unchanged regardless of the chosen fuel efficiency map data density. According to the sensitivity analysis study, three parameters (fuel consumption map data, driving force, and gross vehicle weight have the greatest impact on fuel efficiency (±5% to ±10% changes.

Fuel assembly