Two-dimensional direct numerical simulation of bubble cloud cavitation by front-tracking method

International Nuclear Information System (INIS)

Peng, G; Shimizu, S; Tryggvason, G

2015-01-01

Unsteady bubble cloud cavitation phenomenon caused by negative pressure pulse has been treated numerically by applying a front tracking method. The behaviour of bubble cloud expanding and contracting is evaluated by tracking the motion of all bubble interfaces. Numerical investigation demonstrates that: (1) In the collapsing of bubble cloud micro liquid jets toward the inner bubbles are formed while the outer layer bubbles contract extremely, and then a high impact pressure is released when the inner central bubble contacts to its minimum. (2) The oscillation of bubble cloud depends upon the void fraction greatly. In the case of high void fraction, the frequency of cloud oscillation is lower than that of individual bubble and the decay of the oscillation becomes much slowly also

DISP: Optimizations towards Scalable MPI Startup

Energy Technology Data Exchange (ETDEWEB)

Fu, Huansong [Florida State University, Tallahassee; Pophale, Swaroop S [ORNL; Gorentla Venkata, Manjunath [ORNL; Yu, Weikuan [Florida State University, Tallahassee

2016-01-01

Despite the popularity of MPI for high performance computing, the startup of MPI programs faces a scalability challenge as both the execution time and memory consumption increase drastically at scale. We have examined this problem using the collective modules of Cheetah and Tuned in Open MPI as representative implementations. Previous improvements for collectives have focused on algorithmic advances and hardware off-load. In this paper, we examine the startup cost of the collective module within a communicator and explore various techniques to improve its efficiency and scalability. Accordingly, we have developed a new scalable startup scheme with three internal techniques, namely Delayed Initialization, Module Sharing and Prediction-based Topology Setup (DISP). Our DISP scheme greatly benefits the collective initialization of the Cheetah module. At the same time, it helps boost the performance of non-collective initialization in the Tuned module. We evaluate the performance of our implementation on Titan supercomputer at ORNL with up to 4096 processes. The results show that our delayed initialization can speed up the startup of Tuned and Cheetah by an average of 32.0% and 29.2%, respectively, our module sharing can reduce the memory consumption of Tuned and Cheetah by up to 24.1% and 83.5%, respectively, and our prediction-based topology setup can speed up the startup of Cheetah by up to 80%.

MO-FG-BRD-02: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: MV Tracking

Energy Technology Data Exchange (ETDEWEB)

Berbeco, R. [Brigham and Women’s Hospital and Dana-Farber Cancer Institute (United States)

2015-06-15

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow.

MO-FG-BRD-04: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: MR Tracking

Energy Technology Data Exchange (ETDEWEB)

Low, D. [University of California Los Angeles: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: MR Tracking (United States)

2015-06-15

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow.

MO-FG-BRD-03: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: EM Tracking

Energy Technology Data Exchange (ETDEWEB)

Keall, P. [University of Sydney (Australia)

2015-06-15

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow.

MO-FG-BRD-04: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: MR Tracking

International Nuclear Information System (INIS)

Low, D.

2015-01-01

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow

MO-FG-BRD-03: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: EM Tracking

International Nuclear Information System (INIS)

Keall, P.

2015-01-01

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow

MO-FG-BRD-02: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: MV Tracking

International Nuclear Information System (INIS)

Berbeco, R.

2015-01-01

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow

The influence of cricket fast bowlers' front leg technique on peak ground reaction forces.

Science.gov (United States)

Worthington, Peter; King, Mark; Ranson, Craig

2013-01-01

High ground reaction forces during the front foot contact phase of the bowling action are believed to be a major contributor to the high prevalence of lumbar stress fractures in fast bowlers. This study aimed to investigate the influence of front leg technique on peak ground reaction forces during the delivery stride. Three-dimensional kinematic data and ground reaction forces during the front foot contact phase were captured for 20 elite male fast bowlers. Eight kinematic parameters were determined for each performance, describing run-up speed and front leg technique, in addition to peak force and time to peak force in the vertical and horizontal directions. There were substantial variations between bowlers in both peak forces (vertical 6.7 ± 1.4 body weights; horizontal (braking) 4.5 ± 0.8 body weights) and times to peak force (vertical 0.03 ± 0.01 s; horizontal 0.03 ± 0.01 s). These differences were found to be linked to the orientation of the front leg at the instant of front foot contact. In particular, a larger plant angle and a heel strike technique were associated with lower peak forces and longer times to peak force during the front foot contact phase, which may help reduce the likelihood of lower back injuries.

Differences between the CME fronts tracked by an expert, an automated algorithm, and the Solar Stormwatch project

Science.gov (United States)

Barnard, L.; Scott, C. J.; Owens, M.; Lockwood, M.; Crothers, S. R.; Davies, J. A.; Harrison, R. A.

2015-10-01

Observations from the Heliospheric Imager (HI) instruments aboard the twin STEREO spacecraft have enabled the compilation of several catalogues of coronal mass ejections (CMEs), each characterizing the propagation of CMEs through the inner heliosphere. Three such catalogues are the Rutherford Appleton Laboratory (RAL)-HI event list, the Solar Stormwatch CME catalogue, and, presented here, the J-tracker catalogue. Each catalogue uses a different method to characterize the location of CME fronts in the HI images: manual identification by an expert, the statistical reduction of the manual identifications of many citizen scientists, and an automated algorithm. We provide a quantitative comparison of the differences between these catalogues and techniques, using 51 CMEs common to each catalogue. The time-elongation profiles of these CME fronts are compared, as are the estimates of the CME kinematics derived from application of three widely used single-spacecraft-fitting techniques. The J-tracker and RAL-HI profiles are most similar, while the Solar Stormwatch profiles display a small systematic offset. Evidence is presented that these differences arise because the RAL-HI and J-tracker profiles follow the sunward edge of CME density enhancements, while Solar Stormwatch profiles track closer to the antisunward (leading) edge. We demonstrate that the method used to produce the time-elongation profile typically introduces more variability into the kinematic estimates than differences between the various single-spacecraft-fitting techniques. This has implications for the repeatability and robustness of these types of analyses, arguably especially so in the context of space weather forecasting, where it could make the results strongly dependent on the methods used by the forecaster.

Simulations of mixing in Inertial Confinement Fusion with front tracking and sub-grid scale models

Science.gov (United States)

Rana, Verinder; Lim, Hyunkyung; Melvin, Jeremy; Cheng, Baolian; Glimm, James; Sharp, David

2015-11-01

We present two related results. The first discusses the Richtmyer-Meshkov (RMI) and Rayleigh-Taylor instabilities (RTI) and their evolution in Inertial Confinement Fusion simulations. We show the evolution of the RMI to the late time RTI under transport effects and tracking. The role of the sub-grid scales helps capture the interaction of turbulence with diffusive processes. The second assesses the effects of concentration on the physics model and examines the mixing properties in the low Reynolds number hot spot. We discuss the effect of concentration on the Schmidt number. The simulation results are produced using the University of Chicago code FLASH and Stony Brook University's front tracking algorithm.

Momentum--"Evaluating Your Marketing Program: Measuring and Tracking Techniques."

Science.gov (United States)

Meservey, Lynne D.

1990-01-01

Suggests 10 tracking techniques for evaluating marketing performance. Techniques involve utilization rate, inquiry and source of inquiry tracking, appointment and interview tracking, enrollment conversion, cost per inquiry and per enrollment, retention rate, survey results, and "mystery shopper." (RJC)

Uranium content of petroleum by fission track technique

International Nuclear Information System (INIS)

Paschoa, A.S.; Mafra, O.Y.; Oliveira, C.A.N. de; Pinto, L.R.

1981-03-01

The feasibility of the fission track registration technique to investigate the natural uranium concentration in petroleum is examined. The application of this technique to petroleum is briefly described and discussed critically. The results obtained so far indicate uranium concentrations in samples of Brazilian petroleum which are over the detect ion limit of fission track technique. (Author) [pt

MO-FG-BRD-01: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: Introduction and KV Tracking

International Nuclear Information System (INIS)

Fahimian, B.

2015-01-01

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow

MO-FG-BRD-01: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management: Introduction and KV Tracking

Energy Technology Data Exchange (ETDEWEB)

Fahimian, B. [Stanford University (United States)

2015-06-15

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow.

Instrumentation of the upgraded ATLAS tracker with a double buffer front-end architecture for track triggering

International Nuclear Information System (INIS)

Wardrope, D

2012-01-01

The Large Hadron Collider will be upgraded to provide instantaneous luminosity L = 5 × 10 34 cm −2 s −1 , leading to excessive rates from the ATLAS Level-1 trigger. A double buffer front-end architecture for the ATLAS tracker replacement is proposed, that will enable the use of track information in trigger decisions within 20 μs in order to reduce the high trigger rates. Analysis of ATLAS simulations have found that using track information will enable the use of single lepton triggers with transverse momentum thresholds of p T ∼ 25 GeV, which will be of great benefit to the future physics programme of ATLAS.

Principal-vector-directed fringe-tracking technique.

Science.gov (United States)

Zhang, Zhihui; Guo, Hongwei

2014-11-01

Fringe tracking is one of the most straightforward techniques for analyzing a single fringe pattern. This work presents a principal-vector-directed fringe-tracking technique. It uses Gaussian derivatives for estimating fringe gradients and uses hysteresis thresholding for segmenting singular points, thus improving the principal component analysis method. Using it allows us to estimate the principal vectors of fringes from a pattern with high noise. The fringe-tracking procedure is directed by these principal vectors, so that erroneous results induced by noise and other error-inducing factors are avoided. At the same time, the singular point regions of the fringe pattern are identified automatically. Using them allows us to determine paths through which the "seed" point for each fringe skeleton is easy to find, thus alleviating the computational burden in processing the fringe pattern. The results of a numerical simulation and experiment demonstrate this method to be valid.

The feasibility of using Pareto fronts for comparison of treatment planning systems and delivery techniques

International Nuclear Information System (INIS)

Ottosson, Rickard O.; Sjoestroem, David; Behrens, Claus F.; Karlsson, Anna; Engstroem, Per E.; Knoeoes, Tommy; Ceberg, Crister

2009-01-01

Pareto optimality is a concept that formalises the trade-off between a given set of mutually contradicting objectives. A solution is said to be Pareto optimal when it is not possible to improve one objective without deteriorating at least one of the other. A set of Pareto optimal solutions constitute the Pareto front. The Pareto concept applies well to the inverse planning process, which involves inherently contradictory objectives, high and uniform target dose on one hand, and sparing of surrounding tissue and nearby organs at risk (OAR) on the other. Due to the specific characteristics of a treatment planning system (TPS), treatment strategy or delivery technique, Pareto fronts for a given case are likely to differ. The aim of this study was to investigate the feasibility of using Pareto fronts as a comparative tool for TPSs, treatment strategies and delivery techniques. In order to sample Pareto fronts, multiple treatment plans with varying target conformity and dose sparing of OAR were created for a number of prostate and head and neck IMRT cases. The DVHs of each plan were evaluated with respect to target coverage and dose to relevant OAR. Pareto fronts were successfully created for all studied cases. The results did indeed follow the definition of the Pareto concept, i.e. dose sparing of the OAR could not be improved without target coverage being impaired or vice versa. Furthermore, various treatment techniques resulted in distinguished and well separated Pareto fronts. Pareto fronts may be used to evaluate a number of parameters within radiotherapy. Examples are TPS optimization algorithms, the variation between accelerators or delivery techniques and the degradation of a plan during the treatment planning process. The issue of designing a model for unbiased comparison of parameters with such large inherent discrepancies, e.g. different TPSs, is problematic and should be carefully considered

The feasibility of using Pareto fronts for comparison of treatment planning systems and delivery techniques.

Science.gov (United States)

Ottosson, Rickard O; Engstrom, Per E; Sjöström, David; Behrens, Claus F; Karlsson, Anna; Knöös, Tommy; Ceberg, Crister

2009-01-01

Pareto optimality is a concept that formalises the trade-off between a given set of mutually contradicting objectives. A solution is said to be Pareto optimal when it is not possible to improve one objective without deteriorating at least one of the other. A set of Pareto optimal solutions constitute the Pareto front. The Pareto concept applies well to the inverse planning process, which involves inherently contradictory objectives, high and uniform target dose on one hand, and sparing of surrounding tissue and nearby organs at risk (OAR) on the other. Due to the specific characteristics of a treatment planning system (TPS), treatment strategy or delivery technique, Pareto fronts for a given case are likely to differ. The aim of this study was to investigate the feasibility of using Pareto fronts as a comparative tool for TPSs, treatment strategies and delivery techniques. In order to sample Pareto fronts, multiple treatment plans with varying target conformity and dose sparing of OAR were created for a number of prostate and head & neck IMRT cases. The DVHs of each plan were evaluated with respect to target coverage and dose to relevant OAR. Pareto fronts were successfully created for all studied cases. The results did indeed follow the definition of the Pareto concept, i.e. dose sparing of the OAR could not be improved without target coverage being impaired or vice versa. Furthermore, various treatment techniques resulted in distinguished and well separated Pareto fronts. Pareto fronts may be used to evaluate a number of parameters within radiotherapy. Examples are TPS optimization algorithms, the variation between accelerators or delivery techniques and the degradation of a plan during the treatment planning process. The issue of designing a model for unbiased comparison of parameters with such large inherent discrepancies, e.g. different TPSs, is problematic and should be carefully considered.

Application of startup/core management code system to YGN 3 startup testing

International Nuclear Information System (INIS)

Chi, Sung Goo; Hah, Yung Joon; Doo, Jin Yong; Kim, Dae Kyum

1995-01-01

YGN 3 is the first nuclear power plant in Korea to use the fixed incore detector system for startup testing and core management. The startup/core management code system was developed from existing ABB-C-E codes and applied for YGN 3 startup testing, especially for physics and CPC(Core Protection Calculator)/COLSS (Core Operating Limit Supervisory System) related testing. The startup/core management code system consists of startup codes which include the CEBASE, CECOR, CEFAST and CEDOPS, and startup data reduction codes which include FLOWRATE, COREPERF, CALMET, and VARTAV. These codes were implemented on an HP/Apollo model 9000 series 400 workstation at the YGN 3 site and successfully applied to startup testing and core management. The startup codes made a great contribution in upgrading the reliability of test results and reducing the test period by taking and analyzing core data automatically. The data reduction code saved the manpower and time for test data reduction and decreased the chance for error in the analysis. It is expected that this code system will make similar contributions for reducing the startup testing duration of YGN 4 and UCN3,4

Business Startups: An analysis of selection and post-startup performance (Japanese)

OpenAIRE

YASUDA Takehiko

2010-01-01

This paper investigates how the pre-startup circumstances surrounding an entrepreneur, during the time when he or she decides to start a business, affects the post-startup performance. Based on the original dataset, sample selection models are estimated connecting nascent entrepreneurs' selection of a startup with actual entrepreneurs' performance post-startup. The results of this paper confirm that the individual attributes of nascent entrepreneurs, which make it easier (difficult) to decide...

Loop Heat Pipe Startup Behaviors

Science.gov (United States)

Ku, Jentung

2016-01-01

A loop heat pipe must start successfully before it can commence its service. The startup transient represents one of the most complex phenomena in the loop heat pipe operation. This paper discusses various aspects of loop heat pipe startup behaviors. Topics include the four startup scenarios, the initial fluid distribution between the evaporator and reservoir that determines the startup scenario, factors that affect the fluid distribution between the evaporator and reservoir, difficulties encountered during the low power startup, and methods to enhance the startup success. Also addressed are the pressure spike and pressure surge during the startup transient, and repeated cycles of loop startup and shutdown under certain conditions.

Software Startups - A Research Agenda

Directory of Open Access Journals (Sweden)

Michael Unterkalmsteiner

2016-10-01

Full Text Available Software startup companies develop innovative, software-intensive products within limited time frames and with few resources, searching for sustainable and scalable business models. Software startups are quite distinct from traditional mature software companies, but also from micro-, small-, and medium-sized enterprises, introducing new challenges relevant for software engineering research. This paper's research agenda focuses on software engineering in startups, identifying, in particular, 70+ research questions in the areas of supporting startup engineering activities, startup evolution models and patterns, ecosystems and innovation hubs, human aspects in software startups, applying startup concepts in non-startup environments, and methodologies and theories for startup research. We connect and motivate this research agenda with past studies in software startup research, while pointing out possible future directions. While all authors of this research agenda have their main background in Software Engineering or Computer Science, their interest in software startups broadens the perspective to the challenges, but also to the opportunities that emerge from multi-disciplinary research. Our audience is therefore primarily software engineering researchers, even though we aim at stimulating collaborations and research that crosses disciplinary boundaries. We believe that with this research agenda we cover a wide spectrum of the software startup industry current needs.

Remote sensing of coastal fronts and their effects on oil dispersion

Energy Technology Data Exchange (ETDEWEB)

Klemas, V

1980-01-01

The use of remote sensing techniques to determine the properties of coastal and estuarine fronts, which represent regions of discontinuities and high gradients in ocean physical parameters such as velocity and density, and to assess the influence of such fronts on oil pollutants is discussed. Results of an aircraft and boat verification study of an oil drift and spread model in Delaware Bay are indicated which illustrate the tendency of oil slicks to be attracted to frontal regions, where a denser fluid underlies a lighter fluid giving rise to an inclined interface with convergence zones. Landsat imagery of the bay acquired in order to incorporate frontal information into the interactive computer model is then presented which allows the locations of coastal fronts to be charted throughout a tidal cycle. It is noted that satellite observations of flood-associated fronts on the New Jersey side of the bay and ebb-associated fronts on the Delaware side agree with boat measurements and model predictions, and that the remote tracking of fronts by aircraft and satellites will aid in oil slick clean-up operations.

Startup of a Joule-heated glass melter with a graphite slurry

International Nuclear Information System (INIS)

Allen, T.L.; Porter, M.A.; Routt, K.R.

1984-01-01

Startup of a Joule-heated glass melter using a graphite slurry as a conducting medium was demonstrated. This technique can be used for the initial startup and for the restart of a melter used for vitrifying high-level radioactive waste. Theory, physical property data, and a demonstration test are reported

MODEL OF IT-STARTUPS MANAGEMENT

Directory of Open Access Journals (Sweden)

Ольга Андреевна КОЗИНА

2017-03-01

Full Text Available Decrease mortality of startups during first three years of existing is an important task of the economy of any country. It has been established that the existing methods of enterprise management have some disadvantages or limits for using in IT-startups management. Analysis of mortality reasons of startups in different stages of their life cycle has been carried out. The comparing of reasons why startups in different time intervals, in different areas of them functioning are failure showed that the run out of cash and the use of not viable business model have appeared mortality factors most often denoted by ex-leaders of startups. The model of startup management based on the lean startup model has been developed. Steps for the management of startups along first two stages of their life cycle were added. We noted that it is important to select set of static points and changeable points of startup during the process of formulation of the business model. Steps to reduce the number of iterations in the method of the lean startup are proposed.

Startup development: strategic point of view

OpenAIRE

ZOPUNYAN Y.S.

2015-01-01

The article analyses different strategies of the startup development. The author considers such phases of the startup development as pre-startup, launch, post-startup. The author analyzes factors that affect startup development. The paper presents conclusions about key elements of startup's strategic development.

A Sales Execution Strategy Guide for Technology Startups

Directory of Open Access Journals (Sweden)

Ian Gilbert

2011-10-01

Full Text Available The majority of startups fail to consider sales execution as part of their overall strategy. This article demonstrates how a sales execution strategy can help a company take a product or service to market more efficiently and effectively by focusing on the customers that are key to generating revenue. Combined with techniques for recruiting effectively and measuring sales outcomes, a sales execution strategy helps technology startups exceed growth aspirations and potentially reduce or even eliminate the requirement for external investment. In this article, we first describe the focus of assistance currently given to startups and the reasons why sales execution strategies are often overlooked. Next, we outline recommendations for developing, implementing, and supporting a sales execution strategy. Finally, we summarize the key points presented in the article.

Critical Incidents of Growth in Nordic eHealth Service Start-Ups

Directory of Open Access Journals (Sweden)

Martti Saarela

2017-06-01

Full Text Available Digitalisation can revolutionise healthcare delivery and provide new business opportunities for innovative start-ups. Start-up businesses in the healthcare service sector are a promising source of new employment and innovations. The start-up stage is the most critical period for the survival of a business, as decisions made during the early stages have a definitive influence on success. This study seeks to clarify the early development of eHealth service start-ups. To summarise the research problem, the authors ask the following question: What are the critical incidents related to the early development of eHealth service start-ups? The units of analysis in this study are 14 Nordic eHealth service start-ups located in Sweden and Finland. The Critical Incident Technique (CIT and semi-structured interviews were applied for data collection. The results are of interest to the public sector, which plays an essential role in healthcare as a service producer, but also as a creator of the business conditions of and opportunities for small businesses.

Uranium content of petroleum by Fission track technique

International Nuclear Information System (INIS)

Paschaa, A.S.; Mafra, O.Y.; Oliveira, C.A.N.; Pinto, L.R.

1982-01-01

This paper examines the feasibility of the fission track registration technique to investigate the natural uranium concentration in petroleum. The application is briefly described and the results obtained indicate the presence of uranium concentrations in samples of Brazilian petroleum which are over the detection limit of the fission track technique. The irradiations were performed by using fluxes with predominance of thermal neutrons, which have a fission cross-section for U 235 equal to 579 barns. Since the neutron fluxes were not comp sed exclusively of thermal neutrons, fissions from fast neutrons would also be taken into account for U 238 and Th 232

MO-FG-BRD-00: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-06-15

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow.

MO-FG-BRD-00: Real-Time Imaging and Tracking Techniques for Intrafractional Motion Management

International Nuclear Information System (INIS)

2015-01-01

Intrafraction target motion is a prominent complicating factor in the accurate targeting of radiation within the body. Methods compensating for target motion during treatment, such as gating and dynamic tumor tracking, depend on the delineation of target location as a function of time during delivery. A variety of techniques for target localization have been explored and are under active development; these include beam-level imaging of radio-opaque fiducials, fiducial-less tracking of anatomical landmarks, tracking of electromagnetic transponders, optical imaging of correlated surrogates, and volumetric imaging within treatment delivery. The Joint Imaging and Therapy Symposium will provide an overview of the techniques for real-time imaging and tracking, with special focus on emerging modes of implementation across different modalities. In particular, the symposium will explore developments in 1) Beam-level kilovoltage X-ray imaging techniques, 2) EPID-based megavoltage X-ray tracking, 3) Dynamic tracking using electromagnetic transponders, and 4) MRI-based soft-tissue tracking during radiation delivery. Learning Objectives: Understand the fundamentals of real-time imaging and tracking techniques Learn about emerging techniques in the field of real-time tracking Distinguish between the advantages and disadvantages of different tracking modalities Understand the role of real-time tracking techniques within the clinical delivery work-flow

The front-end electronics for the 1.8-kchannel SiPM tracking plane in the NEW detector

International Nuclear Information System (INIS)

Rodríguez, J.; Lorca, D.; Monrabal, F.; Toledo, J.; Esteve, R.

2015-01-01

NEW is the first phase of NEXT-100 experiment, an experiment aimed at searching for neutrinoless double-beta decay. NEXT technology combines an excellent energy resolution with tracking capabilities thanks to a combination of optical sensors, PMTs for the energy measurement and SiPMs for topology reconstruction. Those two tools result in one of the highest background rejection potentials in the field. This work describes the tracking plane that will be constructed for the NEW detector which consists of close to 1800 sensors with a 1-cm pitch arranged in twenty-eight 64-SiPM boards. Then it focuses in the development of the electronics needed to read the 1800 channels with a front-end board that includes per-channel differential transimpedance input amplifier, gated integrator, automatic offset voltage compensation and 12-bit ADC. Finally, a description of how the FPGA buffers data, carries out zero suppression and sends data to the DAQ interface using CERN RD-51 SRS's DTCC link specification complements the description of the electronics of the NEW detector tracking plane

Physical startup tests for VVER-1200 of Novovoronezh NPP. Advanced technique and some results

Energy Technology Data Exchange (ETDEWEB)

Afanasiev, Dmitry A.; Kraynov, Yury A.; Pinegin, Anatoly A.; Tsyganov, Sergey V. [National Research Centre, Moscow (Russian Federation). Kurchatov Inst.

2017-09-15

The intention of the startup physics tests was to confirm design characteristics of the core loading and their compliance with safety analysis preconditions. The program of startup tests for the leading unit is usually composed in such a way that is is possible to study as much neutron-physical characteristics as possible in the safest condition of zero power. State-of-the-art safety analysis is including computer codes that use three dimensional neutron kinetics and thermohydraulics models. For the substantiation of such models, for its validation and verification there is a need in reactor experiments that implementing spatially distributed transients. We based on such statements when composing hot zero power physical startup program for the new VVER-1200 unit of Novovoronezh NPP. Several tests unconventional for VVER were developed for that program. It includes measuring the worth for each of control rod groups and measuring of single rod worth from the inserted groups - test that models rod ejection event in some sense.

Comparative Study of Time-Frequency Decomposition Techniques for Fault Detection in Induction Motors Using Vibration Analysis during Startup Transient

Directory of Open Access Journals (Sweden)

Paulo Antonio Delgado-Arredondo

2015-01-01

Full Text Available Induction motors are critical components for most industries and the condition monitoring has become necessary to detect faults. There are several techniques for fault diagnosis of induction motors and analyzing the startup transient vibration signals is not as widely used as other techniques like motor current signature analysis. Vibration analysis gives a fault diagnosis focused on the location of spectral components associated with faults. Therefore, this paper presents a comparative study of different time-frequency analysis methodologies that can be used for detecting faults in induction motors analyzing vibration signals during the startup transient. The studied methodologies are the time-frequency distribution of Gabor (TFDG, the time-frequency Morlet scalogram (TFMS, multiple signal classification (MUSIC, and fast Fourier transform (FFT. The analyzed vibration signals are one broken rotor bar, two broken bars, unbalance, and bearing defects. The obtained results have shown the feasibility of detecting faults in induction motors using the time-frequency spectral analysis applied to vibration signals, and the proposed methodology is applicable when it does not have current signals and only has vibration signals. Also, the methodology has applications in motors that are not fed directly to the supply line, in such cases the analysis of current signals is not recommended due to poor current signal quality.

Estudio de las Startups

OpenAIRE

Rodríguez Reina, Cristina

2016-01-01

Este trabajo trata de analizar las pautas a la hora de poner en marcha una startup. Se explica el método que hay que seguir (Lean Startup), se expone una breve biografía de su autor, se muestran las distintas fases por las que atraviesa, las formas de financiación, así como una serie de puntos que servirán de ayuda para adentrarse en este mundo tan novedoso y hasta entonces tan poco conocido, como es el de la startups. Dentro del ámbito de las startups, se explicará el tema ...

A novel optical investigation technique for railroad track inspection and assessment

Science.gov (United States)

Sabato, Alessandro; Beale, Christopher H.; Niezrecki, Christopher

2017-04-01

Track failures due to cross tie degradation or loss in ballast support may result in a number of problems ranging from simple service interruptions to derailments. Structural Health Monitoring (SHM) of railway track is important for safety reasons and to reduce downtime and maintenance costs. For this reason, novel and cost-effective track inspection technologies for assessing tracks' health are currently insufficient and needed. Advancements achieved in recent years in cameras technology, optical sensors, and image-processing algorithms have made machine vision, Structure from Motion (SfM), and three-dimensional (3D) Digital Image Correlation (DIC) systems extremely appealing techniques for extracting structural deformations and geometry profiles. Therefore, optically based, non-contact measurement techniques may be used for assessing surface defects, rail and tie deflection profiles, and ballast condition. In this study, the design of two camera-based measurement systems is proposed for crossties-ballast condition assessment and track examination purposes. The first one consists of four pairs of cameras installed on the underside of a rail car to detect the induced deformation and displacement on the whole length of the track's cross tie using 3D DIC measurement techniques. The second consists of another set of cameras using SfM techniques for obtaining a 3D rendering of the infrastructure from a series of two-dimensional (2D) images to evaluate the state of the track qualitatively. The feasibility of the proposed optical systems is evaluated through extensive laboratory tests, demonstrating their ability to measure parameters of interest (e.g. crosstie's full-field displacement, vertical deflection, shape, etc.) for assessment and SHM of railroad track.

MODEL OF IT-STARTUPS MANAGEMENT

OpenAIRE

КОЗИНА, Ольга Андреевна; СТРАТИЕНКО, Наталия Константиновна

2017-01-01

Decrease mortality of startups during first three years of existing is an important task of the economy of any country. It has been established that the existing methods of enterprise management have some disadvantages or limits for using in IT-startups management. Analysis of mortality reasons of startups in different stages of their life cycle has been carried out. The comparing of reasons why startups in different time intervals, in different areas of them functioning are failure showed th...

Front end optimization for the monolithic active pixel sensor of the ALICE Inner Tracking System upgrade

International Nuclear Information System (INIS)

Kim, D.; Rinella, G. Aglieri; Cavicchioli, C.; Hillemanns, H.; Hristozkov, S.; Junique, A.; Keil, M.; Kofarago, M.; Kugathasan, T.; Mager, M.; Chanlek, N.; Collu, A.; Degerli, Y.; Flouzat, C.; Guilloux, F.; Dorokhov, A.; Gajanana, D.; Gao, C.; Kwon, Y.; Lattuca, A.

2016-01-01

ALICE plans to replace its Inner Tracking System during the second long shut down of the LHC in 2019 with a new 10 m 2 tracker constructed entirely with monolithic active pixel sensors. The TowerJazz 180 nm CMOS imaging Sensor process has been selected to produce the sensor as it offers a deep pwell allowing full CMOS in-pixel circuitry and different starting materials. First full-scale prototypes have been fabricated and tested. Radiation tolerance has also been verified. In this paper the development of the charge sensitive front end and in particular its optimization for uniformity of charge threshold and time response will be presented

Front end optimization for the monolithic active pixel sensor of the ALICE Inner Tracking System upgrade

Science.gov (United States)

Kim, D.; Aglieri Rinella, G.; Cavicchioli, C.; Chanlek, N.; Collu, A.; Degerli, Y.; Dorokhov, A.; Flouzat, C.; Gajanana, D.; Gao, C.; Guilloux, F.; Hillemanns, H.; Hristozkov, S.; Junique, A.; Keil, M.; Kofarago, M.; Kugathasan, T.; Kwon, Y.; Lattuca, A.; Mager, M.; Sielewicz, K. M.; Marin Tobon, C. A.; Marras, D.; Martinengo, P.; Mazza, G.; Mugnier, H.; Musa, L.; Pham, T. H.; Puggioni, C.; Reidt, F.; Riedler, P.; Rousset, J.; Siddhanta, S.; Snoeys, W.; Song, M.; Usai, G.; Van Hoorne, J. W.; Yang, P.

2016-02-01

ALICE plans to replace its Inner Tracking System during the second long shut down of the LHC in 2019 with a new 10 m2 tracker constructed entirely with monolithic active pixel sensors. The TowerJazz 180 nm CMOS imaging Sensor process has been selected to produce the sensor as it offers a deep pwell allowing full CMOS in-pixel circuitry and different starting materials. First full-scale prototypes have been fabricated and tested. Radiation tolerance has also been verified. In this paper the development of the charge sensitive front end and in particular its optimization for uniformity of charge threshold and time response will be presented.

Tokamak startup: problems and scenarios related to the transient phases of ignited tokamak operations

International Nuclear Information System (INIS)

Sheffield, J.

1985-01-01

During recent years improvements have been made to tokamak startup procedures, which are important to the optimization of ignited tokamaks. The use of rf-assisted startup and noninductive current drive has led to substantial reduction and even complete elimination of the volt-seconds used during startup, relaxing constraints on poloidal coil, vacuum vessel, and structure design. This paper reviews these and other improvements and discusses the various bulk heating techniques that may be used to ignite a D-T plasma

Waste Isolation Pilot Plant (WIPP) startup plan

International Nuclear Information System (INIS)

1988-03-01

To allow the Waste Isolation Pilot Plant (WIPP) to transition from a Major System Acquisition to an operating demonstration facility, the Acquisition Executive and the Energy System Acquisition Advisory Board (ESAAB) must concur in the facility's readiness to receive waste. This action, designated in DOE Order 4700.1 as Key Decision Four, concludes with the Chairman of the ESAAB issuing a Record of Decision. Since the meeting leading to the Record of Decision is scheduled for August 1988, plans must be made to ensure all activities contributing to that decision are completed in a clear and well-coordinated process. To support that effort, this Start-Up Plan was prepared to identify and track key events necessary to verify WIPP's readiness to receive waste; this provides a management/scheduling/tracking tool for the DOE WIPP Project Office (WPO) and a tracking mechanism for the DOE Albuquerque Operations Office (DOE-AL) and for DOE Headquarters (DOE-HQ); and describe the process to ensure readiness is documented by providing relevant data and reports to the cognizant decision makers. The methods by which these two purposes are achieved are discussed in further detail in the remainder of this plan

Combining Front Vehicle Detection with 3D Pose Estimation for a Better Driver Assistance

Directory of Open Access Journals (Sweden)

Yu Peng

2012-09-01

Full Text Available Driver assistant systems enhance traffic safety and efficiency. The accurate 3D pose of a front vehicle can help a driver to make the right decision on the road. We propose a novel real-time system to estimate the 3D pose of the front vehicle. This system consists of two parallel threads: vehicle rear tracking and mapping. The vehicle rear is first identified in the video captured by an onboard camera, after license plate localization and foreground extraction. The 3D pose estimation technique is then employed with respect to the extracted vehicle rear. Most current 3D pose estimation techniques need prior models or a stereo initialization with user cooperation. It is extremely difficult to obtain prior models due to the varying appearance of vehicles' rears. Moreover, it is unsafe to ask for drivers' cooperation when a vehicle is running. In our system, two initial keyframes for stereo algorithms are automatically extracted by vehicle rear detection and tracking. Map points are defined as a collection of point features extracted from the vehicle's rear with their 3D information. These map points are inferences that relate the 2D features detected in following vehicles' rears with the 3D world. The relative 3D pose of the onboard camera to the front vehicle rear is then estimated through matching the map points with point features detected on the front vehicle rear. We demonstrate the capabilities of our system by testing on real-time and synthesized videos. In order to make the experimental analysis visible, we demonstrated an estimated 3D pose through augmented reality, which needs accurate and real-time 3D pose estimation.

Utilizing Z-track Air Lock Technique to Reduce Pain in Intramuscular Injections

Directory of Open Access Journals (Sweden)

Evelyn Hemme Tambunan

2015-04-01

Full Text Available Introduction: Injection is one of most painful and common medical interventions that more than 12 billion of it are administered annually throughout the world. Pain remains as one of the unresolved health problems. The objective of this research was to investigate the pain severity utilizing the z-track air lock technique during intra muscular injection procedure. Method:This study was conducted as an unblinded cinical trial, where 90 female subjects aged between 18-25 years old were randomly assigned to three groups of 30. Each group received z-track air lock (Group ZTAL, air lock (AL, and z-track (Group ZT techniques. Neurobion 5000 vitamin used as an injection substance.A Verbal Rating Scale (VRS on 0–3 was used to evaluate the severity of pain during procedure. Data were analized using the SPSS version 19. Groups’ age, Body Mass Index (BMI and pain severity were analyzed through descriptive and One Way ANOVA statistics. Results: Results showed that there were no signifi cant differences of pain severity both within and between groups (p > 0.05. Discussion: Both Z-track and air lock method are less pain compared to traditional method according to previous studies. Noncicepti stimulus inhibited nocicepti stimulus in z-track technique while locking effect inhibit leakeage of substance injection to subcutaneous layer of skin which contain of nerve fi bers. However All techniques are recommended to produce less pain therefore it can be considered as a standard procedure for intra muscular injection. Keywords: intramuscular injection, z-track air lock technique, pain

Startup activities of established Finnish companies

OpenAIRE

Saalasti, Sini

2016-01-01

Established companies have collaborated with startups for decades in order to enhance their capabilities in technology and innovation. However, in the recent years, the changes in the business environment have induced established companies to increase their collaboration with startups. Thus, startup activities of established companies have become a timely phenomenon. This study explores the startup activities of established companies by analyzing all the activity established companies conduct...

Bootstrap finance: the art of start-ups.

Science.gov (United States)

Bhide, A

1992-01-01

Entrepreneurship is more popular than ever: courses are full, policymakers emphasize new ventures, managers yearn to go off on their own. Would-be founders often misplace their energies, however. Believing in a "big money" model of entrepreneurship, they spend a lot of time trying to attract investors instead of using wits and hustle to get their ideas off the ground. A study of 100 of the 1989 Inc. "500" list of fastest growing U.S. start-ups attests to the value of bootstrapping. In fact, what it takes to start a business often conflicts with what venture capitalists require. Investors prefer solid plans, well-defined markets, and track records. Entrepreneurs are heavy on energy and enthusiasm but may be short on credentials. They thrive in rapidly changing environments where uncertain prospects may scare off established companies. Rolling with the punches is often more important than formal plans. Striving to adhere to investors' criteria can diminish the flexibility--the try-it, fix-it approach--an entrepreneur needs to make a new venture work. Seven principles are basic for successful start-ups: get operational fast; look for quick break-even, cash-generating projects; offer high-value products or services that can sustain direct personal selling; don't try to hire the crack team; keep growth in check; focus on cash; and cultivate banks early. Growth and change are the start-up's natural environment. But change is also the reward for success: just as ventures grow, their founders usually have to take a fresh look at everything again: roles, organization, even the very policies that got the business up and running.

Least-squares wave-front reconstruction of Shack-Hartmann sensors and shearing interferometers using multigrid techniques

International Nuclear Information System (INIS)

Baker, K.L.

2005-01-01

This article details a multigrid algorithm that is suitable for least-squares wave-front reconstruction of Shack-Hartmann and shearing interferometer wave-front sensors. The algorithm detailed in this article is shown to scale with the number of subapertures in the same fashion as fast Fourier transform techniques, making it suitable for use in applications requiring a large number of subapertures and high Strehl ratio systems such as for high spatial frequency characterization of high-density plasmas, optics metrology, and multiconjugate and extreme adaptive optics systems

Solenoid-free plasma startup in NSTX using transient CHI

International Nuclear Information System (INIS)

Raman, R.; Jarboe, T.R.; Nelson, B.A.; Mueller, D.; Bell, M.G.; Bell, R.; Gates, D.; Gerhardt, S.; Hosea, J.; Kaita, R.; Kugel, H.; LeBlanc, B.; Menard, J.; Ono, M.; Paul, S.; Roquemore, L.; Maingi, R.; Maqueda, R.; Nagata, M.; Sabbagh, S.

2009-01-01

Experiments in NSTX have now demonstrated the coupling of toroidal plasmas produced by the technique of coaxial helicity injection (CHI) to inductive sustainment and ramp-up of the toroidal plasma current. In these discharges, the central Ohmic transformer was used to apply an inductive loop voltage to discharges with a toroidal current of about 100 kA created by CHI. The coupled discharges have ramped up to >700 kA and transitioned into an H-mode demonstrating compatibility of this startup method with conventional operation. The electron temperature in the coupled discharges reached over 800 eV and the resulting plasma had low inductance, which is preferred for long-pulse high-performance discharges. These results from NSTX in combination with the previously obtained record 160 kA non-inductively generated startup currents in an ST or tokamak in NSTX demonstrate that CHI is a viable solenoid-free plasma startup method for future STs and tokamaks.

Advanced automation concepts applied to Experimental Breeder Reactor-II startup

International Nuclear Information System (INIS)

Berkan, R.C.; Upadhyaya, B.R.; Bywater, R.L.

1991-08-01

The major objective of this work is to demonstrate through simulations that advanced liquid-metal reactor plants can be operated from low power by computer control. Development of an automatic control system with this objective will help resolve specific issues and provide proof through demonstration that automatic control for plant startup is feasible. This paper presents an advanced control system design for startup of the Experimental Breeder Reactor-2 (EBR-2) located at Idaho Falls, Idaho. The design incorporates recent methods in nonlinear control with advanced diagnostics techniques such as neural networks to form an integrated architecture. The preliminary evaluations are obtained in a simulated environment by a low-order, valid nonlinear model. Within the framework of phase 1 research, the design includes an inverse dynamics controller, a fuzzy controller, and an artificial neural network controller. These three nonlinear control modules are designed to follow the EBR-2 startup trajectories in a multi-input/output regime. They are coordinated by a supervisory routine to yield a fault-tolerant, parallel operation. The control system operates in three modes: manual, semiautomatic, and fully automatic control. The simulation results of the EBR-2 startup transients proved the effectiveness of the advanced concepts. The work presented in this paper is a preliminary feasibility analysis and does not constitute a final design of an automated startup control system for EBR-2. 14 refs., 43 figs

Quality assurance during preoperational testing and during startup operation

International Nuclear Information System (INIS)

Eisele, H.; Meyer, F.A.

1980-01-01

Rules and guidelines for the quality assurance. Quality assurance in the course of preoperational testing and the startup period: preoperational testing; hot functional test I; hot functional test II; initial making critical and zero power physics testing; power range testing. Startup documents: startup program; startup instructions; startup data sheet; startup sequence outlines; final startup reports. Advisory safety committee for nuclear startup. (orig./RW)

Instrumentation of a Level-1 Track Trigger at ATLAS with Double Buffer Front-End Architecture

CERN Document Server

Cooper, B; The ATLAS collaboration

2012-01-01

Around 2021 the Large Hadron Collider will be upgraded to provide instantaneous luminosities 5x10^34, leading to excessive rates from the ATLAS Level-1 trigger. We describe a double-buffer front-end architecture for the ATLAS tracker replacement which should enable tracking information to be used in the Level-1 decision. This will allow Level-1 rates to be controlled whilst preserving high efficiency for single lepton triggers at relatively low transverse momentum thresholds pT ~25 GeV, enabling ATLAS to remain sensitive to physics at the electroweak scale. In particular, a potential hardware solution for the communication between the upgraded silicon barrel strip detectors and the external processing within this architecture will be described, and discrete event simulations used to demonstrate that this fits within the tight latency constraints.

Light duty utility arm startup plan

International Nuclear Information System (INIS)

Barnes, G.A.

1998-01-01

This Startup Plan encompasses activities necessary to perform startup and operation of the LDUA in Facility Group 3 tanks and complete turnover to CPO. The activities discussed in this plan will occur prior to, and following the US Department Energy, Richland Operations Office Operational Readiness Review. This startup plan does not authorize or direct any specific field activities or authorize a change of configuration. As such, this startup plan need not be Unresolved Safety Question (USQ) screened

Is there a lean future for global startups?

DEFF Research Database (Denmark)

Tanev, Stoyan

2017-01-01

This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing on gl......-based global startup research and practice. The analysis should benefit both researchers and practitioners in technology entrepreneurship, international entrepreneurship, and global innovation management.......This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing...... on global startups, and further substantiates the articulation of the need for considering the lean global startup as a new type of firm. The main message is that the lessons learned from the emergence of lean startup entrepreneurship offer a basis for promoting a similar lean phase in technology...

Startup and shutdown of the PULSAR Tokamak Reactor

International Nuclear Information System (INIS)

Werley, K.A.; Bathke, C.G.

1994-01-01

Start-up conditions are examined for a pulsed tokamak reactor that uses only inductive plasma current drive for startup, burn and shutdown. A zero-dimensional (profile-averaged) model that describes plasma power and particle balance equations is used to study several aspects of plasma startup and shutdown, including optimization of the startup pathway tradeoff of auxiliary startup heating power versus startup time, volt-second consumtion, thermal stability and partial-power operations

Overview of Maximum Power Point Tracking Techniques for Photovoltaic Energy Production Systems

DEFF Research Database (Denmark)

Koutroulis, Eftichios; Blaabjerg, Frede

2015-01-01

A substantial growth of the installed photovoltaic systems capacity has occurred around the world during the last decade, thus enhancing the availability of electric energy in an environmentally friendly way. The maximum power point tracking technique enables maximization of the energy production...... of photovoltaic sources during stochastically varying solar irradiation and ambient temperature conditions. Thus, the overall efficiency of the photovoltaic energy production system is increased. Numerous techniques have been presented during the last decade for implementing the maximum power point tracking...... process in a photovoltaic system. This article provides an overview of the operating principles of these techniques, which are suited for either uniform or non-uniform solar irradiation conditions. The operational characteristics and implementation requirements of these maximum power point tracking...

The role of relationships in start-up development

DEFF Research Database (Denmark)

Mattsson, Jan; Helmersson, Helge; Standing, Craig

2017-01-01

Relationships are important in the business start-up phase for a variety of reasons. Internal relationships can support knowledge exchange that determines the business model development and external relationships can facilitate a wide range of opportunities, support and insights. The paper explains...... the key relationships experienced by the founding team of a recently formed Swedish digital trading platform. Data were gathered through a self-reporting diary approach based on the Critical Incident Technique format and texts were analysed by the Pertex text-analytic software. The findings explain how...... important relationships were formed during the initial start-up period targeting international expansion. Interaction with early adopters enabled a rapid evolution of the business platform with the aim to build a community of users to support development....

Vision-based vehicle detection and tracking algorithm design

Science.gov (United States)

Hwang, Junyeon; Huh, Kunsoo; Lee, Donghwi

2009-12-01

The vision-based vehicle detection in front of an ego-vehicle is regarded as promising for driver assistance as well as for autonomous vehicle guidance. The feasibility of vehicle detection in a passenger car requires accurate and robust sensing performance. A multivehicle detection system based on stereo vision has been developed for better accuracy and robustness. This system utilizes morphological filter, feature detector, template matching, and epipolar constraint techniques in order to detect the corresponding pairs of vehicles. After the initial detection, the system executes the tracking algorithm for the vehicles. The proposed system can detect front vehicles such as the leading vehicle and side-lane vehicles. The position parameters of the vehicles located in front are obtained based on the detection information. The proposed vehicle detection system is implemented on a passenger car, and its performance is verified experimentally.

Solenoid-free Plasma Start-up in NSTX using Transient CHI

International Nuclear Information System (INIS)

R. Raman, B.A. Nelson, D. Mueller, T.R. Jarboe, M.G. Bell, B. LeBlanc, R. Maqueda, J. Menard, M. Ono, M. Nagata, L. Roquemore, and V. Soukhanovskii

2008-01-01

Experiments in NSTX have now unambiguously demonstrated the coupling of toroidal plasmas produced by the technique of CHI to inductive sustainment and ramp-up of the toroidal plasma current. This is an important step because an alternate method for plasma startup is essential for developing a fusion reactor based on the spherical torus concept. Elimination of the central solenoid would also allow greater flexibility in the choice of the aspect ratio in tokamak designs now being considered. The transient CHI method for spherical torus startup was originally developed on the HIT-II experiment at the University of Washington

The fission-track analysis: An alternative technique for provenance studies of prehistoric obsidian artefacts

CERN Document Server

Bellot-Gurlet, L; Dorighel, O; Oddone, M; Poupeau, G; Yegingil, Z

1999-01-01

Comparison of fission-track parameters - age and track densities - is an alternative tool for correlating obsidian artefacts with their potential natural sources. This method was applied by different fission-track groups in various regions and results were compared with those obtained using the more popular provenance identification techniques based on chemical composition studies. Hundreds of analyses prove that fission-track dating is a complementary technique which turns out to be very useful, specially when the chemical composition does not fully discriminate different sources. Archaeologically significant results were obtained applying the fission-track analysis in various regions of earth.

The fission-track analysis: An alternative technique for provenance studies of prehistoric obsidian artefacts

International Nuclear Information System (INIS)

Bellot-Gurlet, L.; Bigazzi, G.; Dorighel, O.; Oddone, M.; Poupeau, G.; Yegingil, Z.

1999-01-01

Comparison of fission-track parameters - age and track densities - is an alternative tool for correlating obsidian artefacts with their potential natural sources. This method was applied by different fission-track groups in various regions and results were compared with those obtained using the more popular provenance identification techniques based on chemical composition studies. Hundreds of analyses prove that fission-track dating is a complementary technique which turns out to be very useful, specially when the chemical composition does not fully discriminate different sources. Archaeologically significant results were obtained applying the fission-track analysis in various regions of earth

Characterization of silicon microstrip sensors, front-end electronics, and prototype tracking detectors for the CBM experiment at FAIR

International Nuclear Information System (INIS)

Sorokin, Iurii

2013-01-01

The Compressed Baryonic Matter (CBM) experiment will explore the phase diagram of strongly interacting matter in the region of high net baryonic densities. The matter at the extreme conditions will be studied in collisions of a heavy ion beam with a fixed heavy element target. The present work is devoted to the development of the main component of the CBM experiment - the Silicon Tracking System (STS). The STS has to enable reconstruction of up to 1000 charged particle tracks per nucleus-nucleus interaction at the rate of up to 10 MHz, provide a momentum resolution Δp/p of 1 %, and withstand the radiation load of up to 10 14 n eq /cm 2 (n eq -neutron equivalent). The STS will be based on double-sided silicon microstrip sensors, that will be arranged in 8 planes in the aperture of the dipole magnet. Selftriggering readout electronics will be located on the periphery of the detecting planes, and connected to the sensors with low mass microcables. In the stage of R and D, as well as in the stages of pre-series and series production, characterization of the sensors, of the front-end electronics, and of the complete detector modules has to be performed. In the present work the required techniques were developed, and the performance of the latest detector prototypes was evaluated. A particular attention is paid to evaluation of the signal amplitude, as it is one of the most important detector characteristics. Techniques for measuring the passive electrical characteristics of the sensors were developed. These include: the coupling and the interstrip capacitances, the interstrip resistance, the bias resistance, the strip leakage current, the bulk capacitance, and the bulk leakage current. The techniques will be applied for the quality assurance of the sensors during the pre-series and the series production. Extensive characterization of the prototype readout chip, n-XYTER, was performed. The register settings were optimized, and the dependence of the amplitude response on

Automatic counting of fission fragments tracks using the gas permeation technique

CERN Document Server

Yamazaki, I M

1999-01-01

An automatic counting system for fission tracks induced in a polycarbonate plastic Makrofol KG (10 mu m thickness) is described. The method is based on the gas transport mechanism proposed by Knudsen, where the gas permeability for a porous membrane is expected to be directly related to its track density. In this work, nitrogen permeabilities for several Makrofol films, with different fission track densities, have been measured using an adequate gas permeation system. The fission tracks were produced by irradiating Makrofol foils with a 252Cf calibrated source in a 2 pi geometry. A calibration curve fission track number versus nitrogen permeability has been obtained, for track densities higher than 1000/cm sup 2 , where the spark gap technique and the visual methods employing a microscope, are not appropriate for track counting.

SBWR core thermal hydraulic analysis during startup

International Nuclear Information System (INIS)

Lin, J.H.; Huang, R.L.; Sawyer, C.D.

1993-01-01

This paper reports on a thermal hydraulic analysis of the SIMPLIFIED BOILING WATER REACTOR (SBWR) during startup. The potential instability during a SBWR startup has drawn the attention of designers, researchers, and engineers. It has not been a concern for a Boiling Water Reactor (BWR) with forced recirculation; however, for SBWR with natural circulation the concern exists. The concern is about the possibility of a geysering mode oscillation during SBWR startup from a cold temperature and a low system pressure with a low natural circulation flow rate. A thermal hydraulic analysis of the SBWR is performed in simulation of the startup using the TRACG computer code. The temperature, pressure, and reactor power profiles of SBWR during the startup are presented. The results are compared with the data of a natural circulation boiling water reactor, the DODEWAARD plant, in which no instabilities have been observed during many startups. It is shown that a SBWR startup which follows proper procedures, geysering and other modes of oscillations can be avoided

APPLICATION OF OBJECT ORIENTED PROGRAMMING TECHNIQUES IN FRONT END COMPUTERS

International Nuclear Information System (INIS)

SKELLY, J.F.

1997-01-01

The Front End Computer (FEC) environment imposes special demands on software, beyond real time performance and robustness. FEC software must manage a diverse inventory of devices with individualistic timing requirements and hardware interfaces. It must implement network services which export device access to the control system at large, interpreting a uniform network communications protocol into the specific control requirements of the individual devices. Object oriented languages provide programming techniques which neatly address these challenges, and also offer benefits in terms of maintainability and flexibility. Applications are discussed which exhibit the use of inheritance, multiple inheritance and inheritance trees, and polymorphism to address the needs of FEC software

Efficient Photovoltaic System Maximum Power Point Tracking Using a New Technique

Directory of Open Access Journals (Sweden)

Mehdi Seyedmahmoudian

2016-03-01

Full Text Available Partial shading is an unavoidable condition which significantly reduces the efficiency and stability of a photovoltaic (PV system. When partial shading occurs the system has multiple-peak output power characteristics. In order to track the global maximum power point (GMPP within an appropriate period a reliable technique is required. Conventional techniques such as hill climbing and perturbation and observation (P&O are inadequate in tracking the GMPP subject to this condition resulting in a dramatic reduction in the efficiency of the PV system. Recent artificial intelligence methods have been proposed, however they have a higher computational cost, slower processing time and increased oscillations which results in further instability at the output of the PV system. This paper proposes a fast and efficient technique based on Radial Movement Optimization (RMO for detecting the GMPP under partial shading conditions. The paper begins with a brief description of the behavior of PV systems under partial shading conditions followed by the introduction of the new RMO-based technique for GMPP tracking. Finally, results are presented to demonstration the performance of the proposed technique under different partial shading conditions. The results are compared with those of the PSO method, one of the most widely used methods in the literature. Four factors, namely convergence speed, efficiency (power loss reduction, stability (oscillation reduction and computational cost, are considered in the comparison with the PSO technique.

Lean start-up

DEFF Research Database (Denmark)

Rasmussen, Erik Stavnsager; Tanev, Stoyan

2016-01-01

The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The ma...... and the final business model. In other words: The start-up must first nail the problem together with the customers, then develop the solution and test, and then in the end scale it to a full-grown business model.......The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The main...

Is There a Lean Future for Global Startups?

Directory of Open Access Journals (Sweden)

Stoyan Tanev

2017-05-01

Full Text Available This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing on global startups, and further substantiates the articulation of the need for considering the lean global startup as a new type of firm. The main message is that the lessons learned from the emergence of lean startup entrepreneurship offer a basis for promoting a similar lean phase in technology-based global startup research and practice. The analysis should benefit both researchers and practitioners in technology entrepreneurship, international entrepreneurship, and global innovation management.

A 0.18 μm biosensor front-end based on 1/f noise, distortion cancelation and chopper stabilization techniques.

Science.gov (United States)

Balasubramanian, Viswanathan; Ruedi, Pierre-Francois; Temiz, Yuksel; Ferretti, Anna; Guiducci, Carlotta; Enz

2013-10-01

This paper presents a novel sensor front-end circuit that addresses the issues of 1/f noise and distortion in a unique way by using canceling techniques. The proposed front-end is a fully differential transimpedance amplifier (TIA) targeted for current mode electrochemical biosensing applications. In this paper, we discuss the architecture of this canceling based front-end and the optimization methods followed for achieving low noise, low distortion performance at minimum current consumption are presented. To validate the employed canceling based front-end, it has been realized in a 0.18 μm CMOS process and the characterization results are presented. The front-end has also been tested as part of a complete wireless sensing system and the cyclic voltammetry (CV) test results from electrochemical sensors are provided. Overall current consumption in the front-end is 50 μA while operating on a 1.8 V supply.

Usefulness of the Pain Tracking Technique in Acute Mechanical Low Back Pain

Directory of Open Access Journals (Sweden)

Tania Bravo Acosta

2015-01-01

Full Text Available Objective. To evaluate the usefulness of the pain tracking technique in acute mechanical low back pain. Method. We performed an experimental prospective (longitudinal explanatory study between January 2011 and September 2012. The sample was randomly divided into two groups. Patients were assessed at the start and end of the treatment using the visual analogue scale and the Waddell test. Treatment consisted in applying the pain tracking technique to the study group and interferential current therapy to the control group. At the end of treatment, cryotherapy was applied for 10 minutes. The Wilcoxon signed-rank test and the Mann Whitney test were used. They were performed with a predetermined significance level of p≤0.05. Results. Pain was triggered by prolonged static posture and intense physical labor and intensified through trunk movements and when sitting and standing. The greatest relief was reported in lateral decubitus position and in William’s position. The majority of the patients had contracture. Pain and disability were modified with the rehabilitation treatment in both groups. Conclusions. Both the pain tracking and interferential current techniques combined with cryotherapy are useful treatments for acute mechanical low back pain. The onset of analgesia is faster when using the pain tracking technique.

Startup of a Joule-heated glass melter with a graphite slurry

International Nuclear Information System (INIS)

Allen, T.L.; Routt, K.R.; Porter, M.A.

1983-01-01

This paper discusses the theoretical equations and physical and electrical property data of various graphite slurries for starting up a glass melter. An application test is also included to demonstrate the graphite slurry startup technique

Startup program after SGR and power increase

International Nuclear Information System (INIS)

Krajnc, B.; Dudas, M.; Spiler, J.; Novsak, M.

2000-01-01

NPP Krsko replaced steam generators during the outage 2000. Parallel with the steam generator replacement all required systems modifications to accommodate new steam generators into the existing plant (upper feed,..) and support plant power increase of 6.3%, have been implemented. During the years 1997 - 2000 all the required licensing, technical analyses and systems verifications to support such plant changes have been completed. One of the activities within this effort was also the preparation of a detailed Plant Startup Program, which was subject of licensing review and approval process. An integrated plant startup program was then developed based on the plant startup test program, performed regularly during plant startup after refueling and above-mentioned Plant Startup Program. These additional tests defined by the Startup Test Program have been required due to new steam generators, steam generator replacement and related modifications, and power increase from previous 1882 MWt to 2000 MWt. During the preparation period, a startup team was established and procedures were written. All procedures sensitive to the operation were validated on the plant specific simulator. This paper presents more about the Startup Test Program, analysis of its implementation, the results of some key tests as well as the lessons learned. (author)

Results of solid state nuclear track detector technique application in radon detection, by alpha particles tracks, for uranium prospecting in Caetite (BA-Brazil)

International Nuclear Information System (INIS)

Moraes, M.A.P.V. de; Khouri, M.T.F.C.

1988-11-01

The solid state nuclear track detector technique has been used in radon detection, by alpha particles tracks for uranium prospecting on the ground in Caetite city (Bahia-Brazil). The sensitive film to alpha particles used were CA 8015 exposed during 15 days and the results of three anomalies of this region are showed in a form of maps, made with the density of tracks obtained, and were compared with scintillation counter measurements. The technique showed to be simple and an effective auxiliary for the prospection of uranium ore bodies. The initial uranium exploration costs can be reduced by using this technique. (author) [pt

DOES FAMILY SOCIAL SUPPORT AFFECT STARTUP BUSINESS ACTIVITIES?

Directory of Open Access Journals (Sweden)

Nurlaily F.

2018-02-01

Full Text Available In recent years, StartUp has shown a considerable progress in Indonesia. Although most of the StartUps are newly established companies in phase to find the right markets, the StartUps are expected to contribute to the economy and solve local problems. In Indonesia most of the StartUps are still in the idea stage. Therefore, they have no profit, loss, or even failure. It causes the StartUps to be difficult in gaining trust from investors. To overcome these problems, support from various parties is necessary for the development of StartUp activities. One of them is a support from family (Family Social Support. Previous studies have shown that family support contributes to the success of an entrepreneur. However, there has been no research on the relationship between family support with StartUp activities, especially in developing countries like Indonesia. This study examined the influence of family social support in the form of financial capital support, social capital, human capital, physical capital, and family cohesiveness on StartUp activities in Indonesia by using Poisson regression analysis. The results showed that family cohesiveness had a significant effect on the increase of StartUp activities.

Startup methods for single-mode gyrotron operation

International Nuclear Information System (INIS)

Whaley, D.R.; Tran, M.Q.; Alberti, S.; Tran, T.M.; Antonsen, T.M. Jr.; Dubrovin, A.; Tran, C.

1995-01-01

Experimental results of startup studies on a 118 GHz TE 22,6 gyrotron are presented and compared with theory. The startup paths through the energy-velocity-pitch-angle plane are determined by the time evolution of the beam parameters during the startup phase. These startup paths are modified by changing the anode and cathode voltage rise from zero to their nominal values and are seen to determine the cavity oscillating mode. Experimental results show specifically that competition between the TE 22,6 and TE -19,7 mode can be completely eliminated by use of the proper startup method in a case where a typical triode startup results in oscillation in the competing TE -19,7 mode. These new results are shown to be in excellent agreement with the theory whose approach is general and therefore applicable to gyrotrons operating in any arbitrary cavity mode. (author) 3 figs., 4 refs

Innovative Startup-Projects: Experience, Evaluation, Implementation Contradictions

Directory of Open Access Journals (Sweden)

Inshakov Maksim Olegovich

2015-09-01

Full Text Available Innovative companies in the conditions of global post-crisis economic recovery and increased economic activity become again a promising area for investments of large investment and venture capital funds, venture divisions of large transnational corporations, business angels and other private investors. This is confirmed by the data on the increase in the volume of venture capital market in the US and Europe and on a significant increase in the cost of the leading foreign and Russian start-up companies which are rated as of 2014 in the present article. The comparative analysis of the leading Russian and foreign start-ups showed the prevalence of companies engaged in the field of IT-Internet-Mobile and focused on the provision of various kinds of innovative services to consumers among the foreign participants of the rating. Among Russian startups-winners the companies of technological orientation (biological, medical, and “clean” technologies dominate. They reflect the increasing importance of start-ups in the innovative development of the Russian economy. Participation in such competitions and ratings is a favorable factor of promoting start-ups, increasing awareness of potential investors and consumers of start-up products. The importance of start-ups formation and the development of effective regional and national innovation systems update the studies related to the identification of the fundamental contradictions in the activities of Russian start-ups and to the development of recommendations for their resolution. The article identifies the key issues of economic, organizational, informational and marketing character causing the collapse of start-up projects in the Russian economy in modern conditions.

COMPARISON OF RECURSIVE ESTIMATION TECHNIQUES FOR POSITION TRACKING RADIOACTIVE SOURCES

International Nuclear Information System (INIS)

Muske, K.; Howse, J.

2000-01-01

This paper compares the performance of recursive state estimation techniques for tracking the physical location of a radioactive source within a room based on radiation measurements obtained from a series of detectors at fixed locations. Specifically, the extended Kalman filter, algebraic observer, and nonlinear least squares techniques are investigated. The results of this study indicate that recursive least squares estimation significantly outperforms the other techniques due to the severe model nonlinearity

Startup methods for single-mode gyrotron operation

International Nuclear Information System (INIS)

Whaley, D.R.; Tran, M.Q.; Alberti, S.; Tran, T.M.; Antonsen, T.M.; Tran, C.

1995-03-01

Experimental results of startup studies on a 118 GHz TE 22,6 gyrotron are presented and compared with theory. The theoretical excitation regimes of competing modes are computed in the energy-velocity-pitch-angle plane near the operation point. The startup paths through the plane are determined by the time evolution of the beam parameters during the startup phase. These startup paths are modified by changing the anode and cathode voltage rise from zero to their nominal values and are seen to determine the cavity oscillating mode. Experimental results show specifically that competition between the TE 22,6 and TE -19,7 mode can be completely eliminated by using the proper startup method in a case where a typical triode startup results in oscillation in the competing TE -19,7 mode. These new results are shown to be in excellent agreement with theory whose approach is general and therefore applicable to gyrotrons operating in any arbitrary cavity mode. (author) 5 figs., 1 tab., 13 refs

DOES FAMILY SOCIAL SUPPORT AFFECT STARTUP BUSINESS ACTIVITIES?

OpenAIRE

Nurlaily F.; Aini E.K.; Asmoro P.S.

2018-01-01

In recent years, StartUp has shown a considerable progress in Indonesia. Although most of the StartUps are newly established companies in phase to find the right markets, the StartUps are expected to contribute to the economy and solve local problems. In Indonesia most of the StartUps are still in the idea stage. Therefore, they have no profit, loss, or even failure. It causes the StartUps to be difficult in gaining trust from investors. To overcome these problems, support from various partie...

Long Pulse EBW Start-up Experiments in MAST

Directory of Open Access Journals (Sweden)

Shevchenko V.F.

2015-01-01

Full Text Available Start-up technique reported here relies on a double mode conversion (MC for electron Bernstein wave (EBW excitation. It consists of MC of the ordinary (O mode, entering the plasma from the low field side of the tokamak, into the extraordinary (X mode at a mirror-polarizer located at the high field side. The X mode propagates back to the plasma, passes through electron cyclotron resonance (ECR and experiences a subsequent X to EBW MC near the upper hybrid resonance (UHR. Finally the excited EBW mode is totally absorbed at the Doppler shifted ECR. The absorption of EBW remains high even in cold rarefied plasmas. Furthermore, EBW can generate significant plasma current giving the prospect of a fully solenoid-free plasma start-up. First experiments using this scheme were carried out on MAST [1]. Plasma currents up to 33 kA have been achieved using 28 GHz 100kW 90ms RF pulses. Recently experimental results were extended to longer RF pulses showing further increase of plasma currents generated by RF power alone. A record current of 73kA has been achieved with 450ms RF pulse of similar power. The current drive enhancement was mainly achieved due to RF pulse extension and further optimisation of the start-up scenario.

Lean Startup and Lean Canvas Using for Innovative Product Development

Directory of Open Access Journals (Sweden)

Alena Buchalcevová

2016-06-01

Full Text Available Recently, new approaches to product development have emerged that focus on idea generation techniques and customer itself. One of them is the Lean Startup method that is described in this article along with the Lean Canvas method. The main goal of the article is to demonstrate the application of both methods to an innovative product development focused on providing interactive trips for families with children. The development of the product during individual phases is described and application of the Lean Startup and Lean Canvas principles is demonstrated. Finally, benefits of both methods contributing to the product success are discussed. Similar case studies start emerging worldwide, however in the Czech context are quite rare.

Pixel front-end development in 65 nm CMOS technology

International Nuclear Information System (INIS)

Havránek, M; Hemperek, T; Kishishita, T; Krüger, H; Wermes, N

2014-01-01

Luminosity upgrade of the LHC (HL-LHC) imposes severe constraints on the detector tracking systems in terms of radiation hardness and capability to cope with higher hit rates. One possible way of keeping track with increasing luminosity is the usage of more advanced technologies. Ultra deep sub-micron CMOS technologies allow a design of complex and high speed electronics with high integration density. In addition, these technologies are inherently radiation hard. We present a prototype of analog pixel front-end integrated circuit designed in 65 nm CMOS technology with applications oriented towards the ATLAS Pixel Detector upgrade. The aspects of ultra deep sub-micron design and performance of the analog pixel front-end circuits will be discussed

40 CFR 61.09 - Notification of startup.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Notification of startup. 61.09 Section...) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS General Provisions § 61.09 Notification of startup. (a) The owner or operator of each stationary source which has an initial startup after the effective...

PolarTrack: Optical Outside-In Device Tracking that Exploits Display Polarization

DEFF Research Database (Denmark)

Rädle, Roman; Jetter, Hans-Christian; Fischer, Jonathan

2018-01-01

PolarTrack is a novel camera-based approach to detecting and tracking mobile devices inside the capture volume. In PolarTrack, a polarization filter continuously rotates in front of an off-the-shelf color camera, which causes the displays of observed devices to periodically blink in the camera feed....... The periodic blinking results from the physical characteristics of current displays, which shine polarized light either through an LC overlay to produce images or through a polarizer to reduce light reflections on OLED displays. PolarTrack runs a simple detection algorithm on the camera feed to segment...... displays and track their locations and orientations, which makes PolarTrack particularly suitable as a tracking system for cross-device interaction with mobile devices. Our evaluation of PolarTrack's tracking quality and comparison with state-of-the-art camera-based multi-device tracking showed a better...

A protocol for hit and control synchronous transfer for the front-end electronics at the CBM experiment

Energy Technology Data Exchange (ETDEWEB)

Kasinski, K., E-mail: kasinski@agh.edu.pl [AGH University of Science and Technology, Department of Measurement and Electronics, Av. Mickiewicza 30, 30-059 Cracow (Poland); Szczygiel, R. [AGH University of Science and Technology, Department of Measurement and Electronics, Av. Mickiewicza 30, 30-059 Cracow (Poland); Zabolotny, W. [Institute of Electronic Systems, Warsaw University of Technology, ul. Nowowiejska 15/19, 00-665 Warsaw (Poland); Lehnert, J.; Schmidt, C.J. [GSI Helmholtzzentrum für Schwerionenforschung GmbH, Planckstrasse 1, 64-291 Darmstadt (Germany); Müller, W.F.J. [FAIR Facility for Antiproton and Ion Research in Europe GmbH, Planckstrasse 1, 64-291 Darmstadt (Germany)

2016-11-01

The Silicon Tracking System, Muon Chamber, Transition Radiation Detector and Time-Of-Flight among others are the detector systems of the Compressed Baryonic Matter (CBM) experiment at the FAIR facility. These detector systems will be built with tens of thousands of front-end ASICs exposed to high radiation doses and difficult environmental and interference conditions. A CERN's GBTx-based solution was chosen for combining data from multiple front-end ASICs into an optical link before further concentration and preprocessing in the common Data Processing Board data hub. This paper presents the protocol design addressing the DAQ system requirements, simplifying the ASIC's back-end design and presents its adaptation for the STS and MUCH detector's conditions. A specific link synchronization technique, hit data bandwidth optimization and time synchronization method for the self-triggered front-end chip are presented.

A protocol for hit and control synchronous transfer for the front-end electronics at the CBM experiment

International Nuclear Information System (INIS)

Kasinski, K.; Szczygiel, R.; Zabolotny, W.; Lehnert, J.; Schmidt, C.J.; Müller, W.F.J.

2016-01-01

The Silicon Tracking System, Muon Chamber, Transition Radiation Detector and Time-Of-Flight among others are the detector systems of the Compressed Baryonic Matter (CBM) experiment at the FAIR facility. These detector systems will be built with tens of thousands of front-end ASICs exposed to high radiation doses and difficult environmental and interference conditions. A CERN's GBTx-based solution was chosen for combining data from multiple front-end ASICs into an optical link before further concentration and preprocessing in the common Data Processing Board data hub. This paper presents the protocol design addressing the DAQ system requirements, simplifying the ASIC's back-end design and presents its adaptation for the STS and MUCH detector's conditions. A specific link synchronization technique, hit data bandwidth optimization and time synchronization method for the self-triggered front-end chip are presented.

Non-Solenoidal Startup Research Directions on the Pegasus Toroidal Experiment

Science.gov (United States)

Fonck, R. J.; Bongard, M. W.; Lewicki, B. T.; Reusch, J. A.; Winz, G. R.

2017-10-01

The Pegasus research program has been focused on developing a physical understanding and predictive models for non-solenoidal tokamak plasma startup using Local Helicity Injection (LHI). LHI employs strong localized electron currents injected along magnetic field lines in the plasma edge that relax through magnetic turbulence to form a tokamak-like plasma. Pending approval, the Pegasus program will address a broader, more comprehensive examination of non-solenoidal tokamak startup techniques. New capabilities may include: increasing the toroidal field to 0.6 T to support critical scaling tests to near-NSTX-U field levels; deploying internal plasma diagnostics; installing a coaxial helicity injection (CHI) capability in the upper divertor region; and deploying a modest (200-400 kW) electron cyclotron RF capability. These efforts will address scaling of relevant physics to higher BT, separate and comparative studies of helicity injection techniques, efficiency of handoff to consequent current sustainment techniques, and the use of ECH to synergistically improve the target plasma for consequent bootstrap and neutral beam current drive sustainment. This has an ultimate goal of validating techniques to produce a 1 MA target plasma in NSTX-U and beyond. Work supported by US DOE Grant DE-FG02-96ER54375.

FFTF startup: status and results

International Nuclear Information System (INIS)

Noordhoff, B.H.; Moore, C.E.

1980-03-01

Startup testing on the Fast Flux Test Facility (FFTF) during the past three years has progressed beyond initial criticality toward the principal goal of power demonstration in 1980. An overview is presented of technical results to date and project plans to achieve power demonstration and complete the startup test program

Simulation of SBWR startup transient and stability

International Nuclear Information System (INIS)

Cheng, H.S.; Khan, H.J.; Rohatgi, U.S.

1998-01-01

The Simplified Boiling Water Reactor (SBWR) designed by General Electric is a natural circulation reactor with enhanced safety features for potential accidents. It has a strong coupling between power and flow in the reactor core, hence the neutronic coupling with thermal-hydraulics is specially important. The potential geysering instability during the early part of a SBWR startup at low flow, low power and low pressure is of particular concern. The RAMONA-4B computer code developed at Brookhaven National Laboratory (BNL) for the SBWR has been used to simulate a SBWR startup transient and evaluate its stability, using a simplified four-channel representation of the reactor core for the thermal-hydraulics. This transient was run for 20,000 sec (5.56 hrs) in order to cover the essential aspect of the SBWR startup. The simulation showed that the SBWR startup was a very challenging event to analyze as it required accurate modeling of the thermal-hydraulics at low pressures. This analysis did not show any geysering instability during the startup, following the startup procedure as proposed by GE

Determination of Nuclear Track Parameters for LR-115 Detector by Using of MATLAB Software Technique

International Nuclear Information System (INIS)

AL-Jomaily, F.M.; AL-joburi, H.A.; Mheemeed, A.K.

2013-01-01

The nuclear track detector parameters, such as nuclear track diameter D(μm), number of track N T and area of track A T were determined by using MATLAB software technique for IR-115 detector irradiated by alpha particle from 241 Am source under 1.5, 2.5 and 3.5 MeV at etching time T B of 90, 120, 150 and 180 min.By using the image analysis of MATLAB software for nuclear track, the full width at half maximum FWHM and relative resolution R% were calculated for each energy of alpha particles.In this study, it was shown that increasing the alpha energy on the IR-115 detector leads to increased etching time T B and the dropping of R% to minimum value, and then reach a stable value before dropping at values 1.5, 2.5 MeV and unstable at 3.5 MeV. Imaging analysis by MATLAB technique which used in this study reflect good and accurate results for nuclear track detector parameters and we recommend using this technique for determination of these parameters

Feasibility studies of a Level-1 Tracking Trigger for ATLAS

CERN Document Server

Warren, M; Brenner, R; Konstantinidis, N; Sutton, M

2009-01-01

The existing ATLAS Level-1 trigger system is seriously challenged at the SLHC's higher luminosity. A hardware tracking trigger might be needed, but requires a detailed understanding of the detector. Simulation of high pile-up events, with various data-reduction techniques applied will be described. Two scenarios are envisaged: (a) regional readout - calorimeter and muon triggers are used to identify portions of the tracker; and (b) track-stub finding using special trigger layers. A proposed hardware system, including data reduction on the front-end ASICs, readout within a super-module and integrating regional triggering into all levels of the readout system, will be discussed.

Lean Start-up in Established Companies

DEFF Research Database (Denmark)

Goduscheit, René Chester

2018-01-01

Lean start-up is an emergent perspective on how entrepreneurs can bring new products and services to the market. This approach challenges the dominant role of lengthy business plans, linear product development processes, and seeking complete overview of the potential of the new products....../services before market launch. Instead it suggests that start-ups could benefit from a ‘minimum-viable product’ approach where products and services are launched when they contain critical features. The emphasis in the lean start-up approach is on business models rather than the elaborate business plan...... at the companies (strategy meetings, development workshops etc.). The aim is to shed light on the implications for companies that seek to employ lean start-up. These implications will be aimed at aspects like innovation management, organizational structure, customer relations etc....

Characterization of silicon microstrip sensors, front-end electronics, and prototype tracking detectors for the CBM experiment at FAIR

Energy Technology Data Exchange (ETDEWEB)

Sorokin, Iurii

2013-07-01

The Compressed Baryonic Matter (CBM) experiment will explore the phase diagram of strongly interacting matter in the region of high net baryonic densities. The matter at the extreme conditions will be studied in collisions of a heavy ion beam with a fixed heavy element target. The present work is devoted to the development of the main component of the CBM experiment - the Silicon Tracking System (STS). The STS has to enable reconstruction of up to 1000 charged particle tracks per nucleus-nucleus interaction at the rate of up to 10 MHz, provide a momentum resolution Δp/p of 1 %, and withstand the radiation load of up to 10{sup 14} n{sub eq}/cm{sup 2} (n{sub eq}-neutron equivalent). The STS will be based on double-sided silicon microstrip sensors, that will be arranged in 8 planes in the aperture of the dipole magnet. Selftriggering readout electronics will be located on the periphery of the detecting planes, and connected to the sensors with low mass microcables. In the stage of R and D, as well as in the stages of pre-series and series production, characterization of the sensors, of the front-end electronics, and of the complete detector modules has to be performed. In the present work the required techniques were developed, and the performance of the latest detector prototypes was evaluated. A particular attention is paid to evaluation of the signal amplitude, as it is one of the most important detector characteristics. Techniques for measuring the passive electrical characteristics of the sensors were developed. These include: the coupling and the interstrip capacitances, the interstrip resistance, the bias resistance, the strip leakage current, the bulk capacitance, and the bulk leakage current. The techniques will be applied for the quality assurance of the sensors during the pre-series and the series production. Extensive characterization of the prototype readout chip, n-XYTER, was performed. The register settings were optimized, and the dependence of the

Start-up simulations of the PULSAR pulsed tokamak reactor

International Nuclear Information System (INIS)

Werley, K.A.; Bathke, C.G.

1993-01-01

Start-up conditions are examined for a pulsed tokamak reactor that uses only inductively driven plasma current (and bootstrap current). A zero-dimensional (profile-averaged) model containing plasma power and particle balance equations is used to study several aspects of plasma start-up, including: (1) optimization of the start-up pathway; (2) tradeoffs of auxiliary start-up heating power versus start-up time; (3) volt-second consumption; (4) thermal stability of the operating point; (5) estimates of the diverter heat flux and temperature during the start-up transient; (6) the sensitivity of the available operating space to allowed values of the H confinement factor; and (7) partial-power operations

Technique of neutron-induced (fission-track) autoradiography with histological detail

International Nuclear Information System (INIS)

Smith, J.M.; Taylor, G.N.; Jee, W.S.S.

1980-01-01

The primary advantage of neutron-induced or fission-track autoradiography compared with conventional autoradiography is that for low concentrations of fissile nuclides prohibitively long exposure times may be avoided. However, it is difficult to produce imaging of biological structures on the neutron-induced autoradiograph which would allow localization of the nuclide histologically. The technique presented circumvents this difficulty using a thin polycarbonate film applied to the histologically stained tissue section mounted on a quartz substrate. After irradiation of the tissue section with an appropriate thermal neutron flux, the fission fragment tracks are revealed by etching the film with KOH. The tracks, superimposed on the stained tissue, may be observed under the light microscope in the same manner as for conventional nuclear emulsion autoradiography

University Start-ups: A Better Business Model

Science.gov (United States)

Dehn, J.; Webley, P. W.

2015-12-01

Many universities look to start-up companies as a way to attract faculty, supporting research and students as traditional federal sources become harder to come by. University affiliated start-up companies can apply for a broader suite of grants, as well as market their services to a broad customer base. Often university administrators see this as a potential panacea, but national statistics show this is not the case. Rarely do universities profit significantly from their start-ups. With a success rates of around 20%, most start-ups end up costing the university money as well as faculty-time. For the faculty, assuming they want to continue in academia, a start-up is often unattractive because it commonly leads out of academia. Running a successful business as well as maintaining a strong teaching and research load is almost impossible to do at the same time. Most business models and business professionals work outside of academia, and the models taught in business schools do not merge well in a university environment. To mitigate this a new business model is proposed where university start-ups are aligned with the academic and research missions of the university. A university start-up must work within the university, directly support research and students, and the work done maintaining the business be recognized as part of the faculty member's university obligations. This requires a complex conflict of interest management plan and for the companies to be non-profit in order to not jeopardize the university's status. This approach may not work well for all universities, but would be ideal for many to conserve resources and ensure a harmonious relationship with their start-ups and faculty.

START-UP FINANCING SOURCES: DOES GENDER MATTER? SOME EVIDENCE FOR EU AND ROMANIA

Directory of Open Access Journals (Sweden)

Badulescu Alina

2011-07-01

sources are the internal ones: own fund and savings (ranging from 82% to 92%, and financial assistance from family and friend (ranging from 25% to 34%, both for male and female entrepreneurs, both for EU as an aggregate and Romania. Among the external sources, bank loans are the most important: they have been indicated by 17% of the females (EU and 19% of the males, about 10 times more than the other external sources together: capital contributions from other enterprises and venture capital. There are no significant gender differences in EU case, and also there are not in the case of Romania. Apparently, gender does not matter about sources used for start-up financing. The most significant difference concerns the financial support from public authorities as financial source. The number of female entrepreneurs indicating financial support from public authorities as a source for start-up financing represents 6.18% in EU, versus 0.17% in Romania (36 times less in Romania than the EU average, while for men the figures are 4.85% in EU versus 0.30% in Romania (16 times less in Romania. This gap brings again in front of policy responsible the imperative of financially supporting nascent entrepreneurs, as the key to sustainable economic growth.

Startup and commissioning of pressurized water reactors

International Nuclear Information System (INIS)

Albert, L.J.; Gilbert, C.F.

1983-05-01

A critical phase of plant development is the test, startup, and commissioning period. The effort expended prior to commissioning has a definite effect on the reliability and continuing availability of the plant during its life. This paper describes a test, startup, and commissioning program for a pressurized water reactor (PWR) plant. This program commences with the completion of construction and continues through the turnover of equipment/systems to the owner's startup/ commissioning group. The paper addresses the organization of the test/startup group, planning and scheduling, test procedures and initial testing, staffing and certification of the test group, training of operators, and turnover to the owner

Growth Hacking for Startups : How Growth Hacking can utilised for growing startups

OpenAIRE

Lee, Jin

2016-01-01

In the era of start-ups, many failed to put out their prototypes or products to the market due to lack of funds or experience in marketing. Growth Hacking is a tool that start-ups can benefit from if they learn what Growth Hacking is and how to implement it. The aim of this thesis is to explore what Growth Hacking is and how to implement it for the commissioner CubiCasa Oy. A couple of Growth Hacking tactics are used for CubiCasa Oy and the process of implementation and findings are rec...

Experience in the Kola NPP start-up works

International Nuclear Information System (INIS)

Zakharov, S.I.; Omel'chuk, V.V.; Bodrukhin, Yu.M.

1984-01-01

Main stages and peculiar features of maintenance and start-up works at WWER-440 type reactor NPPs described. Remarks revealed during complex equipment testing, physical and power start-up will be useful for arrangement of maintenance and start-up works at newly built NPPs

Development of a Front Tracking Method for Two-Phase Micromixing of Incompressible Viscous Fluids with Interfacial Tension in Solvent Extraction

Energy Technology Data Exchange (ETDEWEB)

Zhou, Yijie [ORNL; Lim, Hyun-Kyung [ORNL; de Almeida, Valmor F [ORNL; Navamita, Ray [State University of New York, Stony Brook; Wang, Shuqiang [State University of New York, Stony Brook; Glimm, James G [ORNL; Li, Xiao-lin [State University of New York, Stony Brook; Jiao, Xiangmin [ORNL

2012-06-01

This progress report describes the development of a front tracking method for the solution of the governing equations of motion for two-phase micromixing of incompressible, viscous, liquid-liquid solvent extraction processes. The ability to compute the detailed local interfacial structure of the mixture allows characterization of the statistical properties of the two-phase mixture in terms of droplets, filaments, and other structures which emerge as a dispersed phase embedded into a continuous phase. Such a statistical picture provides the information needed for building a consistent coarsened model applicable to the entire mixing device. Coarsening is an undertaking for a future mathematical development and is outside the scope of the present work. We present here a method for accurate simulation of the micromixing dynamics of an aqueous and an organic phase exposed to intense centrifugal force and shearing stress. The onset of mixing is the result of the combination of the classical Rayleigh- Taylor and Kelvin-Helmholtz instabilities. A mixing environment that emulates a sector of the annular mixing zone of a centrifugal contactor is used for the mathematical domain. The domain is small enough to allow for resolution of the individual interfacial structures and large enough to allow for an analysis of their statistical distribution of sizes and shapes. A set of accurate algorithms for this application requires an advanced front tracking approach constrained by the incompressibility condition. This research is aimed at designing and implementing these algorithms. We demonstrate verification and convergence results for one-phase and unmixed, two-phase flows. In addition we report on preliminary results for mixed, two-phase flow for realistic operating flow parameters.

Numerical simulation of two-phase flow with front-capturing

International Nuclear Information System (INIS)

Tzanos, C.P.; Weber, D.P.

2000-01-01

Because of the complexity of two-phase flow phenomena, two-phase flow codes rely heavily on empirical correlations. This approach has a number of serious shortcomings. Advances in parallel computing and continuing improvements in computer speed and memory have stimulated the development of numerical simulation tools that rely less on empirical correlations and more on fundamental physics. The objective of this work is to take advantage of developments in massively parallel computing, single-phase computational fluid dynamics of complex systems, and numerical methods for front capturing in two-phase flows to develop a computer code for direct numerical simulation of two-phase flow. This includes bubble/droplet transport, interface deformation and topology change, bubble-droplet interactions, interface mass, momentum, and energy transfer. In this work, the Navier-Stokes and energy equations are solved by treating both phases as a single fluid with interfaces between the two phases, and a discontinuity in material properties across the moving interfaces. The evolution of the interfaces is simulated by using the front capturing technique of the level-set methods. In these methods, the boundary of a two-fluid interface is modeled as the zero level set of a smooth function φ. The level-set function φ is defined as the signed distance from the interface (φ is negative inside a droplet/bubble and positive outside). Compared to other front-capturing or front-tracking methods, the level-set approach is relatively easy to implement even in three-dimensional flows, and it has been shown to simulate well the coalescence and breakup of droplets/bubbles

Energy losses on tokamak startup

International Nuclear Information System (INIS)

Murray, J.G.; Rothe, K.E.; Bronner, G.

1983-01-01

During the startup of a tokamak reactor using poloidal field (PF) coils to induce plasma currents, the conducting structures carry induced currents. The associated energy losses in the circuits must be provided by the startup coils and the PF system. This paper provides quantitative and comparitive values for the energies required as a function of the thickness or resistivity of the torus shells

Attempted semen collection using the massage technique in blue-fronted Amazon parrots (Amazona aestiva aestiva).

Science.gov (United States)

Della Volpe, Angelique; Volker, Schmidt; Krautwald-Junghanns, Maria-Elisabeth

2011-03-01

The purpose of this study was to establish a technique for collecting semen from blue-fronted Amazon parrots (Amazona aestiva aestiva) and to evaluate the samples that were collected. The massage method is the most common technique used to collect semen in birds and has been proven successful in several psittacine species; however, collection attempts in larger parrots have been unsatisfactory. Six blue-fronted Amazon parrot males, 3 paired with hens and 3 unpaired, were used in this study. The semen collection technique was revised to allow collection from individual birds by a single person. Semen collection was attempted from the 6 parrots on 52-56 occasions, which totaled 330 single attempts. Nineteen ejaculates were collected, and each bird produced at least 1 ejaculate that contained spermatozoa. Large ranges of sample volume (1-15.4 microL), sperm quality (motility = 2%-60%; live:dead ratio = 2:198 to 185:15), sperm concentration (0.79-3.3 x 10(6) sperm/mL), and contamination rate (0%-100%) were observed. Measured parameters did not appear to be significantly impacted by birds being paired or kept singly. Because of the relatively short acclimation period, the birds appeared to be sexually inactive for the majority of the study. Further research using sexually active birds will be necessary to determine standard spermatological parameters and verify the success of the methodology used here.

Ignited tokamak devices with ohmic-heating dominated startup

International Nuclear Information System (INIS)

Cohn, D.R.; Bromberg, L.; Jassby, D.L.

1986-01-01

Startup of tokamaks such that the auxiliary heating power is significantly less than the ohmic heating power at all times during heating to ignition can be referred to as ''Ohmic-heating dominated startup.'' Operation in this mode could increase the certainty of heating to ignition since energy confinement during startup may be described by present scaling laws for ohmic heating. It could also reduce substantially the auxiliary heating power (the required power may be quite large for auxiliary-heating dominated startup). These advantages might be realized without the potentially demanding requirements for pure ohmic heating to ignition. In this paper the authors discuss the requirements for ohmic-heating dominated startup and present illustrative design parameters for compact experiment ignition devices that use high performance copper magnets

Editorial: Startups (February 2010

Directory of Open Access Journals (Sweden)

Dru Lavigne

2010-01-01

Full Text Available Bob Sutor, Vice President of the Open Source and Linux division at IBM, recently stated that "there doesn't seem to be very many good guides about the nuts and bolts of starting an open source business". He speculates that one reason is that "there is no one way to start and run a business that involves open source". The authors in this issue of the OSBR are serial entrepreneurs, startup founders, and professionals who provide services to and interact daily with startups.

Entrepreneurial patent management in pharmaceutical startups.

Science.gov (United States)

Holgersson, Marcus; Phan, Tai; Hedner, Thomas

2016-07-01

Startups fill an increasingly important role as innovators in the pharmaceutical industry, and patenting is typically central to their success. This article aims to explore patent management in pharmaceutical startups. The results show that startups need to deal with several challenges related to patenting and an 'entrepreneurial' approach to patent management is called for. Resource constraints, venture capital provision, exits and other conditions and events must be readily considered in the patent management process to build a successful pharmaceutical venture, something that could benefit the pharmaceutical industry as a whole. Copyright © 2016 Elsevier Ltd. All rights reserved.

Microbiology and performance of a methanogenic biofilm reactor during the start-up period.

Science.gov (United States)

Cresson, R; Dabert, P; Bernet, N

2009-03-01

To understand the interactions between anaerobic biofilm development and process performances during the start-up period of methanogenic biofilm reactor. Two methanogenic inverse turbulent bed reactors have been started and monitored for 81 days. Biofilm development (adhesion, growth, population dynamic) and characteristics (biodiversity, structure) were investigated using molecular tools (PCR-SSCP, FISH-CSLM). Identification of the dominant populations, in relation to process performances and to the present knowledge of their metabolic activities, was used to propose a global scheme of the degradation routes involved. The inoculum, which determines the microbial species present in the biofilm influences bioreactor performances during the start-up period. FISH observations revealed a homogeneous distribution of the Archaea and bacterial populations inside the biofilm. This study points out the link between biodiversity, functional stability and methanogenic process performances during start-up of anaerobic biofilm reactor. It shows that inoculum and substrate composition greatly influence biodiversity, physiology and structure of the biofilm. The combination of molecular techniques associated to a biochemical engineering approach is useful to get relevant information on the microbiology of a methanogenic growing biofilm, in relation with the start-up of the process.

Guidelines for e-Startup Promotion Strategy

Directory of Open Access Journals (Sweden)

Valerio De Simone

2015-04-01

Full Text Available Abstract Startup businesses have always played an important role in the global economy, but recently their importance has grown significantly. For this reason, governments around the world have amended regulation and created incentives to encourage their development. However, statistics show that startups have an extremely high mortality rate, often due to a lack of strategic planning, wrong marketing investments or inefficient resource allocation. The purpose of this paper is to propose a decision-driven tool which will enable the creation of a successful promotional strategy. The proposed strategy is a three-stage process allowing startups to gradually eliminate non-optimal advertising formats. The first stage focuses on the analysis of the e-market where the startup operates. The second stage is dedicated to the economic environment that the new company will face relative to its available resources. Its aim is to reject overly expensive advertising formats by linking costs to availability of funds. The third and last stage is a cost effectiveness analysis, allowing the entrepreneur to identify the best advertising formats and using an impact-factor as a proxy of effectiveness. The proposed methodology has been applied to the case of an Italian early-stage startup for validation.

20 CFR 632.254 - Program startup.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Program startup. 632.254 Section 632.254 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR INDIAN AND NATIVE AMERICAN EMPLOYMENT AND TRAINING PROGRAMS Summer Youth Employment and Training Programs § 632.254 Program startup...

Dampak Mentoring Pada Keberhasilan Start-Up Business: Studi Kasus Pada Start-Up Business di Indonesia [Mentoring the Impact of Success of a Start-Up Business: A Case Study of a Start-Up Business in Indonesia

Directory of Open Access Journals (Sweden)

Christina Yanita Setyawati

2016-10-01

Full Text Available Entrepreneurship is a highly developed science today, as well as in the world of education in Indonesia. Teaching entrepreneurship at the university level, especially at some universities in Surabaya, the second largest city in Indonesia, shows the positive impact that there were 74.03% of start-up businesses that survived and thrived in 2014. Based on the previous observation, some business start-ups are accompanied by a mentor. Mentoring is a process of forming and maintaining lasting relationships that develop intensively among seniors with juniors. The mentoring function includes career and psychosocial functions. The main purpose of this research is to study the relationship between mentoring and the success of a start-up business. This study is a quantitative descriptive study using a random sampling method to obtain 100 samples. The tool used to collect data was a questionnaire. The methodology used to analyze the quantitative description to test the hypothesis. The results of this study indicate that mentoring influences the success of a start-up business that was owned by university students in Surabaya, Indonesia by 32% and 78% was influenced by other variables.

Active learning of Pareto fronts.

Science.gov (United States)

Campigotto, Paolo; Passerini, Andrea; Battiti, Roberto

2014-03-01

This paper introduces the active learning of Pareto fronts (ALP) algorithm, a novel approach to recover the Pareto front of a multiobjective optimization problem. ALP casts the identification of the Pareto front into a supervised machine learning task. This approach enables an analytical model of the Pareto front to be built. The computational effort in generating the supervised information is reduced by an active learning strategy. In particular, the model is learned from a set of informative training objective vectors. The training objective vectors are approximated Pareto-optimal vectors obtained by solving different scalarized problem instances. The experimental results show that ALP achieves an accurate Pareto front approximation with a lower computational effort than state-of-the-art estimation of distribution algorithms and widely known genetic techniques.

ECRH-assisted start-up in ITER

International Nuclear Information System (INIS)

Lloyd, B.; Carolan, P.G.; Warrick, C.D.

1996-07-01

In ITER, the electric field applied for ionisation and to ramp up the plasma current may be limited to ∼ 0.3 V/m. In this case, based on established theories of the avalanche process, it is shown that ohmic breakdown in ITER is only possible over a narrow range of pressure and magnetic error field. Therefore, ECRH may be necessary to provide robust and reliable start-up. ECRH can ensure prompt breakdown over a wide range of prefill pressure and error field and can also give control over the initial time and location of breakdown. For ECRH-assisted start-up in ITER, the power and pulse length requirements are essentially determined by the need to ensure burnthrough, i.e. complete ionisation of hydrogen and the transition to high ionisation states of impurities. A 0-D code (with inclusion of some 1-D effects) has been developed to analyse burnthrough in ITER. The 0-D simulations indicate that control of the deuterium density is the key factor for ensuring successful start-up in ITER, where the effects of neutral screening and dynamic fuelling by the ex-plasma volume are also crucial. It is concluded that without ECRH, successful start-up will only be possible over a very restricted range of parameters but 3MW of absorbed ECRH power will ensure reasonably robust start-up for a broad range of conditions with beryllium impurity. In the case of carbon impurity, even with an absorbed ECRH power of 5MW one may be restricted to low prefill pressure and/or low carbon concentration for successful start-up. (Author)

Research nuclear reactor start-up simulator

International Nuclear Information System (INIS)

Sofo Haro, M.; Cantero, P.

2009-01-01

This work presents the design and FPGA implementation of a research nuclear reactor start-up simulator. Its aim is to generate a set of signals that allow replacing the neutron detector for stimulated signals, to feed the measurement electronic of the start-up channels, to check its operation, together with the start-up security logic. The simulator presented can be configured on three independent channels and adjust the shape of the output pulses. Furthermore, each channel can be configured in 'rate' mode, where you can specify the growth rate of the pulse frequency in %/s. Result and details of the implementation on FPGA of the different functional blocks are given. (author)

Thermal hydraulic behavior of SCWR sliding pressure startup

International Nuclear Information System (INIS)

Fu Shengwei; Zhou Chong; Xu Zhihong; Yang Yanhua

2011-01-01

The modification to ATHLET-SC code is introduced in this paper, which realizes the simulation of trans-critical transients using two-phase model. With the modified code, the thermal-hydraulic dynamic behavior of the mixed SCWR core during the startup process is simulated. The startup process is similar to the design of SCLWR-H sliding pressure startup. The results show that maximum temperature of cladding-surface does not exceed 650℃ in the whole startup process, and the sudden change of water properties in the trans-critical transients will not cause harmful influence to the heat transfer of the fuel cladding. (authors)

A fission track technique used for hydrogeochemical prospecting in Northern India

International Nuclear Information System (INIS)

Singh, N.P.; Singh, S.; Virk, H.S.

1988-01-01

A fission track technique is employed to determine the uranium content of water samples collected from different locations of the middle and outer Himalayas. The regional threshold for the uranium content is determined for water samples of different areas. The identification of anomalies in an area of uranium mineralization confirmed that the hydrogeochemical technique could successfully be used for uranium exploration. (author)

Predicting start-up success with machine learning

OpenAIRE

Bento, Francisco Ramadas da Silva Ribeiro

2018-01-01

Start-ups are becoming the motor that moves our economy. Google, Apple, or more recently Airbnb and Uber are companies with tremendous impact in worldwide economy, social interactions and government. Over the past decade, both in the US and Europe, there has been an exponential growth in start-up formation. Thus, it seems a relevant challenge understanding what makes this type of high-risk ventures successful and as such, attractive to investors and entrepreneurs. Success for a start-up is de...

A import??ncia do mapeamento de processos em uma startup

OpenAIRE

Neves, Ana Carolina Coelho

2016-01-01

O artigo aborda a import??ncia de mapeamento de processos em uma startup. Com base no referencial te??rico sobre empreendedorismo, cen??rios, startups e mapeamento de processos, identificou-se a import??ncia do mapeamento de processos para as startups. Os objetivos de identificar se as startups possuem mapeamento de processo; identificar em qual momento de ciclo de vida uma startup deve desenvolver um mapeamento de processo; e identificar se o mapeamento de processos gera melhoria para uma st...

Emissions of polychlorinated diphenyl ethers from a municipal solid waste incinerator during the start-up operation

International Nuclear Information System (INIS)

Yang, Jing-Sing; Lin, Sheng-Lun; Lin, Ta-Chang; Wu, Yee-Lin; Wang, Lin-Chi; Chang-Chien, Guo-Ping

2015-01-01

Highlights: • This is the first study on the PCDE emission during a MSWI start-up procedure. • The highest PCDE level occurred similar to the PCDD/F reformation temperature. • The pollution control were modified and reduce 86% PCDE peak emission. • Multiple start-ups are analyzed for their effects on the annual PCDE emission. - Abstract: This study examines the emissions of polychlorinated diphenyl ethers (PCDEs) during the start-up processes of a municipal solid waste incinerator (MSWI). Both normal and modified emission control start-ups were tested. Fifteen samples were taken from the flue gas with increasing furnace temperature. Peak PCDE concentrations of 1.48–10.3 ng/Nm 3 were observed at 8–11 h after the start of combustion, when the furnace temperature was in the range of 267–440 °C, that also needed for PCDD/F formation by de novo synthesis. The PCDE emissions could thus, be reduced by current control techniques. Furthermore, the modified control strategies inhibited PCDE formation at the beginning of combustion, and led to an 86% reduction in the maximum PCDE concentration. The overall start-up emissions were calculated as 1.01–3.08 mg, while the annual PCDE emissions with one start-up operation were found to be 7.48–9.64 mg. However, total PCDE emissions will increase by 12–69% if the number of start-up runs increases to between two and eight times per year. Consequently, the prevention of the unnecessary start-ups and advanced activation of the related emission control system are both efficient ways to reduce PCDE emissions.

Emissions of polychlorinated diphenyl ethers from a municipal solid waste incinerator during the start-up operation

Energy Technology Data Exchange (ETDEWEB)

Yang, Jing-Sing [Department of Environmental Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Lin, Sheng-Lun, E-mail: cbmsgml@gmail.com [Department of Civil Engineering and Geomatics, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Super Micro Mass Research and Technology Center, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Lin, Ta-Chang; Wu, Yee-Lin [Department of Environmental Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Wang, Lin-Chi [Department of Civil Engineering and Geomatics, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Chang-Chien, Guo-Ping, E-mail: guoping@csu.edu.tw [Super Micro Mass Research and Technology Center, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Department of Cosmetic and Fashion Styling, Kaohsiung 83347, Taiwan (China)

2015-12-15

Highlights: • This is the first study on the PCDE emission during a MSWI start-up procedure. • The highest PCDE level occurred similar to the PCDD/F reformation temperature. • The pollution control were modified and reduce 86% PCDE peak emission. • Multiple start-ups are analyzed for their effects on the annual PCDE emission. - Abstract: This study examines the emissions of polychlorinated diphenyl ethers (PCDEs) during the start-up processes of a municipal solid waste incinerator (MSWI). Both normal and modified emission control start-ups were tested. Fifteen samples were taken from the flue gas with increasing furnace temperature. Peak PCDE concentrations of 1.48–10.3 ng/Nm{sup 3} were observed at 8–11 h after the start of combustion, when the furnace temperature was in the range of 267–440 °C, that also needed for PCDD/F formation by de novo synthesis. The PCDE emissions could thus, be reduced by current control techniques. Furthermore, the modified control strategies inhibited PCDE formation at the beginning of combustion, and led to an 86% reduction in the maximum PCDE concentration. The overall start-up emissions were calculated as 1.01–3.08 mg, while the annual PCDE emissions with one start-up operation were found to be 7.48–9.64 mg. However, total PCDE emissions will increase by 12–69% if the number of start-up runs increases to between two and eight times per year. Consequently, the prevention of the unnecessary start-ups and advanced activation of the related emission control system are both efficient ways to reduce PCDE emissions.

A Wireless Fatigue Monitoring System Utilizing a Bio-Inspired Tree Ring Data Tracking Technique

OpenAIRE

Bai, Shi; Li, Xuan; Xie, Zhaohui; Zhou, Zhi; Ou, Jinping

2014-01-01

Fatigue, a hot scientific research topic for centuries, can trigger sudden failure of critical structures such as aircraft and railway systems, resulting in enormous casualties as well as economic losses. The fatigue life of certain structures is intrinsically random and few monitoring techniques are capable of tracking the full life-cycle fatigue damage. In this paper, a novel in-situ wireless real-time fatigue monitoring system using a bio-inspired tree ring data tracking technique is propo...

Measurement of radon and thoron present in the environment using nuclear track etch detector technique

International Nuclear Information System (INIS)

Ramachandran, T.V.; Lalit, B.Y.; Mishra, U.C.

1986-01-01

The use of solid state nuclear track detectors (SSNTD) is one of the most convenient techniques to assess the average radiation levels of alpha activities in the environment. This technique has been used to assess the radon and thoron concentrations in some high background areas of South India and underground non-uranium mines in Bihar State. Exposed SSNTD films are chemically etched in an alkali solution and the alpha tracks are evaluated under an optical microscope. The detailed procedure for this study and the calibration of the etched films for conversion of alpha track density to radon and thoron concentrations in pCi l -1 are given in this paper. It was found that 1.9 tracks cm -2 day -1 and 6.2 tracks cm -2 day -1 were produced by exposing the LR-115 foils to 1 pCi l -1 of thoron and radon respectively. (author)

Feedback from operational experience in front-end transportation

International Nuclear Information System (INIS)

Mondonel, J.L.; Parison, C.

1998-01-01

Transport forms an integral part of the nuclear fuel cycle, representing the strategic link between each stage of the cycle. In a way there is a transport cycle that parallels the nuclear fuel cycle. This concerns particularly the front-end of the cycle whose steps - mining conversion, enrichment and fuel fabrication - require numerous transports. Back-end shipments involve a handful of countries, but front-end transports involve all five continents, and many exotic countries. All over Europe such transports are routinely performed with an excellent safety track record. Transnucleaire dominates the French nuclear transportation market and carries out both front and back-end transports. For instance in 1996 more than 28,400 front-end packages were transported as well as more than 3,600 back-end packages. However front-end transport is now a business undergoing much change. A nuclear transportation company must now cope with an evolving picture including new technical requirements, new transportation schemes and new business conditions. This paper describes the latest evolutions in terms of front-end transportation and the way this activity is carried out by Transnucleaire, and goes on to discuss future prospects. (authors)

On Startups and Doublethink

DEFF Research Database (Denmark)

Egan-Wyer, Carys; Muhr, Sara L.; Rehn, Alf

2018-01-01

a reaction to a perceived outrage or a power imbalance, but isin itselfa constitutive part of contemporary entrepreneurship,particularly as this is culturally constructed. We study this paradox, where a discourse of resistance becomes a productive part of entrepreneurial culture, by way of a case study...... of a successful startup. We analyze the manner in which people working in the startup utilize ‘doublethink’ to portray the organization both as resistance to an assumed, more corporate, ‘Other’ and also as a budding corporation unto itself. By doing so, we highlight how a discourse of resistance works as a value...

Recognition of decays of charged tracks with neural network techniques

International Nuclear Information System (INIS)

Stimpfl-Abele, G.

1991-01-01

We developed neural-network learning techniques for the recognition of decays of charged tracks using a feed-forward network with error back-propagation. Two completely different methods are described in detail and their efficiencies for several NN architectures are compared with conventional methods. Excellent results are obtained. (orig.)

OpenCV and TYZX : video surveillance for tracking.

Energy Technology Data Exchange (ETDEWEB)

He, Jim; Spencer, Andrew; Chu, Eric

2008-08-01

As part of the National Security Engineering Institute (NSEI) project, several sensors were developed in conjunction with an assessment algorithm. A camera system was developed in-house to track the locations of personnel within a secure room. In addition, a commercial, off-the-shelf (COTS) tracking system developed by TYZX was examined. TYZX is a Bay Area start-up that has developed its own tracking hardware and software which we use as COTS support for robust tracking. This report discusses the pros and cons of each camera system, how they work, a proposed data fusion method, and some visual results. Distributed, embedded image processing solutions show the most promise in their ability to track multiple targets in complex environments and in real-time. Future work on the camera system may include three-dimensional volumetric tracking by using multiple simple cameras, Kalman or particle filtering, automated camera calibration and registration, and gesture or path recognition.

OpenCV and TYZX : video surveillance for tracking

International Nuclear Information System (INIS)

He, Jim; Spencer, Andrew; Chu, Eric

2008-01-01

As part of the National Security Engineering Institute (NSEI) project, several sensors were developed in conjunction with an assessment algorithm. A camera system was developed in-house to track the locations of personnel within a secure room. In addition, a commercial, off-the-shelf (COTS) tracking system developed by TYZX was examined. TYZX is a Bay Area start-up that has developed its own tracking hardware and software which we use as COTS support for robust tracking. This report discusses the pros and cons of each camera system, how they work, a proposed data fusion method, and some visual results. Distributed, embedded image processing solutions show the most promise in their ability to track multiple targets in complex environments and in real-time. Future work on the camera system may include three-dimensional volumetric tracking by using multiple simple cameras, Kalman or particle filtering, automated camera calibration and registration, and gesture or path recognition

Business Incubators - the savior of startups? : An exploratory study on knowledge acquisition in a business incubator from a startup perspective

OpenAIRE

Pettersson, Beatrice; Götsén, Anna

2016-01-01

Startups play a vital role in economic development, however, have a high rate of failure, partly due to insufficient knowledge resources. A business incubator is an institution aimed to assist startups with services and resources in order to facilitate their development. There is, however, a gap in previous research regarding knowledge flows and acquisition in business incubators. Furthermore, few scholars have conducted research from the startup perspective in this context. This study, there...

Řízení rozvoje start-up společnosti

OpenAIRE

Paluch, Juraj

2013-01-01

Thesis deals with startup companies and their development methodology. The main aim is to present a model of startup company development. Within the theoretical part successful and unsuccessful businesses are analyzed and selected approaches to the development of startup companies are explained. In practical part, based on the findings a model for startup company development is proposed.

Aloittelevan start-up yrittäjän opas rahoitukseen

OpenAIRE

Lamminsalo, Matti

2015-01-01

Opinnäytetyö käsittelee start-up rahoitusta ja siihen liittyviä toimintamalleja. Opinnäytetyön tuloksena on syntynyt opaskirja: Aloittelevan start-up yrittäjän opas rahoitukseen. Research about start-up ecosystem with investment aspect. As a result guidebook for start-up investment and how to raise a fund was writen.

Start-up Costs, Taxes and Innovative Entrepreneurship

NARCIS (Netherlands)

P. Darnihamedani (Pourya); J.H. Block (Jörn); S.J.A. Hessels (Jolanda); A. Simonyan (Aram)

2015-01-01

markdownabstract__Abstract__ Prior research suggests that start-up costs and taxes negatively influence entry into entrepreneurship. Yet, no distinction is made regarding the type of entrepreneurship, particularly innovative versus non-innovative entrepreneurship. Start-up costs, being one-off

Start-up analysis for marketing strategy.

Science.gov (United States)

Griffith, M J; Baloff, N

1984-01-01

The complex start-up effect on utilization of health care services is too often overlooked or underestimated by marketing planners, leading to a range of negative consequences for both the users of services and the provider organization. Start-up analysis allows accurate estimation of these utilization effects for coordinated strategic planning among marketing finance, and operations.

Tokamak start-up with electron-cyclotron heating

International Nuclear Information System (INIS)

Holly, D.J.; Prager, S.C.; Shepard, D.A.; Sprott, J.C.

1981-01-01

Experiments are described in which the start-up voltage in a tokamak is reduced by about a factor of two by the use of a modest amount of electron cyclotron resonance heating power for pre-ionization. The solution of the zero-dimensional start-up equations indicates that the effect is due to the high initial density which increases the rate at which the conductivity increases in the neutral-dominated initial plasma. The effect extrapolates favourably to larger tokamaks. A 50% reduction in the start-up volt-second requirement and impurity reflux is also observed. (author)

Tokamak start-up with electron-cyclotron heating

Energy Technology Data Exchange (ETDEWEB)

Holly, D J; Prager, S C; Shepard, D A; Sprott, J C [Wisconsin Univ., Madison (USA)

1981-11-01

Experiments are described in which the start-up voltage in a tokamak is reduced by about a factor of two by the use of a modest amount of electron cyclotron resonance heating power for pre-ionization. The solution of the zero-dimensional start-up equations indicates that the effect is due to the high initial density which increases the rate at which the conductivity increases in the neutral-dominated initial plasma. The effect extrapolates favourably to larger tokamaks. A 50% reduction in the start-up volt-second requirement and impurity reflux is also observed.

40 CFR 52.271 - Malfunction, startup, and shutdown regulations.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Malfunction, startup, and shutdown..., startup, and shutdown regulations. (a) The following regulations are disapproved because they would permit... malfunctions and/or fail to sufficiently limit startup and shutdown exemptions to those periods where it is...

Differential sensor in front photopyroelectric technique: I. Theory

Energy Technology Data Exchange (ETDEWEB)

Ivanov, R; Moreno, I [Facultad de Fisica, Universidad Autonoma de Zacatecas, Calz. Solidaridad Esquina Paseo de la Bufa s/n, C.P. 98060, Zacatecas, Zac. (Mexico); Gutierrez-Juarez, G [Instituto de Fisica, Universidad de Guanajuato, Loma del Bosque 103, Lomas del Campestre, C.P. 37150, Leon, Gto. (Mexico); Pichardo-Molina, J L [Centro de Investigaciones en Optica, Loma del Bosque 115, Lomas del Campestre, C.P. 37150, Leon, Gto. (Mexico); Cruz-Orea, A [Departamento de Fisica, CINVESTAV-IPN, Av. IPN 2508, San Pedro Zacatenco, C.P. 07360, Mexico D.F. (Mexico); MarIn, E [Centro de Investigacion en Ciencia Aplicada y TecnologIa Avanzada, Instituto Politecnico Nacional, LegarIa 694, Colonia Irrigacion, C.P. 11500, Mexico D. F. (Mexico)], E-mail: rumen@planck.reduaz.mx

2008-04-21

In this paper the theory of the differential front photopyroelectric technique is developed. The thermal effusivity measurements of a sample through photopyroelectric direct (no-differential) experiments do not have sufficient resolution and accuracy to detect small changes in the thermal effusivity. To assess minor variations in this thermal magnitude, differential methods should be used. These methods compare properties of a reference sample and another unknown sample, which are placed separately in both halves of the differential cell. It is shown that in order to achieve better metrological properties of the differential measurement and electromagnetic interference immunity, the signals of both halves must be subtracted directly at the output of the two parallel connected pyroelectric sensors. The thickness of the samples should have the maximum possible value, at least 10 times higher than the thermal diffusion length for minimum frequency. The results of numerical simulations for the amplitude, phase, real and imaginary parts with water as a reference sample and the other sample with a thermal effusivity very close to that of water (contaminated water) are presented. These results show that measurements should be made in the nearly ideal voltage mode, which ensures a better signal-to-noise ratio than the ideal current mode.

Differential sensor in front photopyroelectric technique: I. Theory

International Nuclear Information System (INIS)

Ivanov, R; Moreno, I; Gutierrez-Juarez, G; Pichardo-Molina, J L; Cruz-Orea, A; MarIn, E

2008-01-01

In this paper the theory of the differential front photopyroelectric technique is developed. The thermal effusivity measurements of a sample through photopyroelectric direct (no-differential) experiments do not have sufficient resolution and accuracy to detect small changes in the thermal effusivity. To assess minor variations in this thermal magnitude, differential methods should be used. These methods compare properties of a reference sample and another unknown sample, which are placed separately in both halves of the differential cell. It is shown that in order to achieve better metrological properties of the differential measurement and electromagnetic interference immunity, the signals of both halves must be subtracted directly at the output of the two parallel connected pyroelectric sensors. The thickness of the samples should have the maximum possible value, at least 10 times higher than the thermal diffusion length for minimum frequency. The results of numerical simulations for the amplitude, phase, real and imaginary parts with water as a reference sample and the other sample with a thermal effusivity very close to that of water (contaminated water) are presented. These results show that measurements should be made in the nearly ideal voltage mode, which ensures a better signal-to-noise ratio than the ideal current mode

Manufacture of anti-bogus label by track-etching technique

International Nuclear Information System (INIS)

He Xiangming; Wan Chunrong

2006-01-01

Anti-bogus label is manufactured by the track-etching technique. The apparent pattern on the label consists of track-etched pores on the membrane. The manufacture of the label depends on the intricate technology and the state strictly controls the sensitive nuclear facilities, ensuring that the label is not copied. The pattern on the label is specially characterized by permeability of liquid in order to distinguish it from a forged one. A genuine label can be distinguished from a sham one by a transparent liquid (e.g. water) or a colorful pen. Nowadays, the products of more than 100 famous brands (trade mark) have been protected from forgery by this technology in the market of China. This is a new method for the utilization of a research reactor

Genetic Counselors in Startup Companies: Redefining the Genetic Counselor Role.

Science.gov (United States)

Rabideau, Marina M; Wong, Kenny; Gordon, Erynn S; Ryan, Lauren

2016-08-01

Genetic counselors (GCs) have recently begun moving into non-clinic based roles in increasing numbers. A relatively new role for GCs is working for startup companies. Startups are newly established companies in the phase of developing and researching new scalable businesses. This article explores the experiences of four GCs working at different startup companies and aims to provide resources for GCs interested in learning more about these types of roles. The article describes startup culture, including a relatively flat organizational structure, quick product iterations, and flexibility, among other unique cultural characteristics. Financial considerations are described, including how to understand and evaluate a company's financial status, along with a brief explanation of alternate forms of compensation including stock options and equity. Specifically, the article details the uncertainties and rewards of working in a fast-paced startup environment that affords opportunities to try new roles and use the genetic counseling skill set in new ways. This article aims to aid GCs in determining whether a startup environment would be a good fit, learning how to evaluate a specific startup, and understanding how to market themselves for positions at startups.

Briu: A Coffee Roasting Startup

OpenAIRE

Beck, Maximilian

2015-01-01

The purpose of this study is to examine the German coffee market and its appropriateness as a new market to enter for the startup Company Briu. The company has been continuously growing since its initial start. The Chilean Coffee startup has since then looked for new markets opportunities in Europe. Their favored market is Germany. The research conducted in this paper is supposed to reveal the market its suitability for the company its expansion. The following key areas are assessed in order ...

Dampak Mentoring Pada Keberhasilan Start-Up Business: Studi Kasus Pada Start-Up Business di Indonesia [Mentoring the Impact of Success of a Start-Up Business: A Case Study of a Start-Up Business in Indonesia

OpenAIRE

Christina Yanita Setyawati

2016-01-01

Entrepreneurship is a highly developed science today, as well as in the world of education in Indonesia. Teaching entrepreneurship at the university level, especially at some universities in Surabaya, the second largest city in Indonesia, shows the positive impact that there were 74.03% of start-up businesses that survived and thrived in 2014. Based on the previous observation, some business start-ups are accompanied by a mentor. Mentoring is a process of forming and maintaining lasting relat...

The performance of the ZEUS central tracking detector z-by-timing electronics in a transputer based data acquisition system

International Nuclear Information System (INIS)

Foster, B.; Heath, G.P.; Llewellyn, T.J.; Gingrich, D.M.; Harnew, N.; Hallam-Baker, P.M.; Khatri, T.; McArthur, I.C.; Morawitz, P.; Nash, J.; Shield, P.D.; Topp-Jorgensen, S.; Wilson, F.F.; Allen, D.B.; Carter, R.C.; Jeffs, M.D.; Morrissey, M.C.; Quinton, S.P.H.; Lane, J.B.; Postranecky, M.

1993-01-01

The Central Tracking Detector of the ZEUS experiment employs a time difference technique to measure the z coordinate of each hit. The method provides fast, three-dimensional space point measurements which are used as input to all levels of the ZEUS trigger. Such a tracking trigger is essential in order to discriminate against events with vertices lying outside the nominal electron-proton interaction region. Since the beam crossing interval of the HERA collider is 96 ns, all data must be pipelined through the front-end readout electronics. Subsequent data aquisition employs a novel technique which utilizes a network of approximately 120 INMOS transputers to process the data in parallel. The z-by-timing method and its data aquisition have been employed successfully in recording and reconstructing tracks from electron-proton interactions in ZEUS. (orig.)

V2I-based startup assistance system at signalized intersections

Directory of Open Access Journals (Sweden)

Jianqiang Wang

2015-08-01

Full Text Available Traffic delays are caused by unskilled vehicle operation and driver distraction during the startup process at signalized intersections. To address this issue, we propose a V2I-based driver assistance system that can acquire the current traffic signal status and provide drivers with startup assistance. This article presents the proposed system’s architecture and an assistance algorithm, which contains two types of driver assistance methods: startup prompting and automatic startup control. The automatic startup control method, based on fuzzy logic control, is validated in simulation tests. We also implement startup prompting using a prototype system and validate its performance in field tests. The test results suggest that the proposed assistance algorithm can help drivers start up their vehicles with less delay, which will significantly improve traffic efficiency.

Cone penetrometer demonstration standard startup review checklist

International Nuclear Information System (INIS)

KRIEG, S.A.

1998-01-01

Startup readiness for the Cone Penetrometer Demonstration in AX Tank Farm will be verified through the application of a Standard Startup Review Checklist. This is a listing of those items essential to demonstrating readiness to start the Cone Penetrometer Demonstration in AX Tank Farm

BWR startup and shutdown activity transport control

Energy Technology Data Exchange (ETDEWEB)

Garcia, S.E., E-mail: sgarcia@epri.com [Electric Power Research Inst. (EPRI), Palo Alto, California (United States); Giannelli, J.F.; Jarvis, A.J., E-mail: jgiannelli@finetech.com, E-mail: ajarvis@finetech.com [Finetech, Inc., Parsippany, New Jersey (United States)

2010-07-01

This paper summarizes BWR industry experience on good practices for controlling the transport of corrosion product activity during shutdowns, particularly refueling outages, and for startup chemistry control to minimize IGSCC (intergranular stress corrosion cracking). For shutdown, overall goals are to minimize adverse impacts of crud bursts and the time required to remove activated corrosion products from the reactor coolant during the shutdown process prior to refueling, and to assist plants in predicting and controlling radiation exposure during outages. For startup, the overall goals are to highlight conditions during early heatup and startup when sources of reactor coolant oxidants are high, when there is a greater likelihood for chemical excursions associated with refueling outage work activities, and when hydrogen injection is not available to mitigate IGSCC due to system design limitations. BWR water chemistry has changed significantly in recent years with the adoption of hydrogen water chemistry, zinc addition and noble metal chemical applications. These processes have, in some instances, resulted in significant activity increases during shutdown evolutions, which together with reduced time for cleanup because of shorter outages, has consequently increased outage radiation exposure. A review several recent outages shows that adverse effects from these conditions can be minimized, leading to the set of good practice recommendations for shutdown chemistry control. Most plants lose the majority of their hydrogen availability hours during early startup because feedwater hydrogen injection systems were not originally designed to inject hydrogen below 20% power. Hydrogen availability has improved through modifications to inject hydrogen at lower power levels, some near 5%. However, data indicate that IGSCC is accelerated during early startup, when dissolved oxygen and hydrogen peroxide levels are high and reactor coolant temperatures are in the 300 to 400 {sup o

Start-up Funding via Equity Crowdfunding in Germany

DEFF Research Database (Denmark)

Angerer, Martin; Brem, Alexander; Kraus, Sascha

2017-01-01

Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types of crowdfund......Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types...... of crowdfunding, and is also known as crowdinvesting in the German-speaking realm. This article predominantly advances the scientific knowledge regarding the success factors of equity crowdfunding for German start-ups. The study conducted nine qualitative interviews with start-ups and crowdinvesting platforms....... Its first result is that German start-ups select crowdinvesting because (1) it is a funding opportunity and (2) it has an expected marketing effect. To organize the results of relevant success factors, the Crowdinvesting Success Model was designed by the researchers. This supports German entrepreneurs...

New Solutions to the Funding Dilemma of Technology Startups

Directory of Open Access Journals (Sweden)

Ali Kousari

2011-05-01

Full Text Available This article explores the current funding challenges facing technology startups and describes new models based on smaller investments and collective action. First, the advantages and disadvantages of traditional startup funding models are presented, with an emphasis on venture capital and angel investment. Next, an overview of existing seed funds, or seed accelerators, shows how entrepreneurs can leverage this approach to access subsequent rounds of funding and create successful ventures. Then, an overview of crowd funding is provided, including examples of companies that have adopted this approach to funding startups and their founders. Finally, the article presents the basis of a new approach that uses crowd funding as means of attracting investors to collectives. In these business ecosystems, startups are exposed to less risk and investors can benefit from attractive returns by investing in these promising startups.

Crowdfunding and the Expansion of Access to Startup Capital

OpenAIRE

Kurt Stanberry; Forrest Aven

2014-01-01

This paper analyzes recent developments in crowdfunding, a new financing technique to improve access to capital. The United States Congress and President Obama, in a rare show of bipartisan action, passed the JOBS Act in 2012 (the Jumpstart Our Business Startups Act). The law is designed to stimulate economic growth and expand job creation by improving access to public capital markets for emerging growth companies. Furthermore, the US is not the only nation attempting to expand access to capi...

Measurement of uranium in human teeth and kidney stones with the fission track technique

International Nuclear Information System (INIS)

Vartanian, R.

1986-01-01

The measurement of uranium in human teeth and in kidney stones was carried out using the fission track activation technique. In this determination 2759 and 2205 absolute counts of tracks for teeth samples and 1689 tracks for kidney stone samples were performed, respectively. The results are as follows: xsub(tooth) (1)=(0.227+-0.006) ppm, xsub(tooth) (2)=(0.143+-0.007) ppm and xsub(kidney)=(0.568+-0.020) ppm. The experimental method is described and the results are discussed. (author)

Tokamak reactor startup power

International Nuclear Information System (INIS)

Weldon, D.M.; Murray, J.G.

1983-01-01

Tokamak startup with ohmic heating (OH)-induced voltages requires rather large voltages and power supplies. On present machines, with no radiofrequency (rf)-assist provisions, hundreds of volts have been specified for their designs. With the addition of electron cyclotron resonant heating (ECRH) assist, the design requirements have been lowered. To obtain information on the cost and complexity associated with this ECRH-assisted, OH-pulsed startup voltage for ignition-type machines, a trade-off study was completed. The Fusion Engineering Device (FED) configuration was selected as a model because information was available on the structure. The data obtained are applicable to all tokamaks of this general size and complexity, such as the Engineering Test Reactor

The Ecosystem of Startups as a Component of the Innovation Ecosystem

Directory of Open Access Journals (Sweden)

Sytnik Natalia I.

2017-08-01

Full Text Available The article analyzes the current theoretical perceptions of the ecosystem of startups and presents the author’s own vision of this entity. It has been proposed to consider the ecosystem of startups as a subsystem of the innovation ecosystem, which aims at creating innovative products and services by startup companies. The ecosystem of startups is an open dynamic system in which the backbone subject is a startup company at various stages of the life cycle. The sustenance subjects in an ecosystem are the organizations, associations and individuals that cause impacts, to varying degrees, on the establishing or development of startups. The activities of the subjects are carried out in the following directions: public regulation, financing, training, information, and infrastructure support for startups. The ecosystem consists of a number of economic, material-and-technical, market, and socio-cultural factors that directly or indirectly influence the actions of the subjects. The vital activity of the ecosystem of startups is maintained by the active interaction of the subjects, connected by a network of internal links with the environment and between themselves.

1-D hybrid code for FRM start-up

International Nuclear Information System (INIS)

Stark, R.A.; Miley, G.H.

1982-01-01

A one-D hybrid has been developed to study the start-up of the FRM via neutral-beam injection. The code uses a multi-group numerical model originally developed by J. Willenberg to describe fusion product dynamics in a solenoidal plasma. Earlier we described such a model for use in determining self-consistent ion currents and magnetic fields in FRM start-up. However, consideration of electron dynamics during start-up indicate that the electron current will oppose the injected ion current and may even foil the attempt to achieve reversal. For this reason, we have combined the multi-group ion (model) with a fluid treatment for electron dynamics to form the hybrid code FROST (Field Reversed One-dimensional STart-up). The details of this merger, along with sample results of operation of FROST, are given

Model checking the FlexRay startup phase

NARCIS (Netherlands)

Cranen, S.

2012-01-01

This report describes a discrete-time model of the startup phase of a FlexRay network. The startup behaviour of this network is analysed in the presence of several faults. It is shown that in certain cases a faulty node can prevent the network from communicating altogether. One previously unknown

Pseudocolor techniques for differentiation of nuclear tracks

International Nuclear Information System (INIS)

Camacho, S.; Laville, A.; Peralta-Fabi, R.; Lira, J.

1984-01-01

Two types of tracks left by 4 He particles at different angles of incidence to CA8015 detectors were successfully discriminated by an SEM coupled to a micro-computer image processing system. To achieve this end, a track signature is defined based on the image's gray level distribution which results from the interaction between the track profile and the electron beam. The principles of track signature extraction, determination of discriminant functions and the design of the ad hoc supervised classifier are described. Finally the possibility of obtaining the track profile through digital analysis of track signatures is discussed. (author)

Thorium content of a mineral ore from Morro do Ferro by fission track technique

International Nuclear Information System (INIS)

Oliveira, C.A.N. de.

1980-10-01

The feasibility to determine thorium concentrations by fission track technique in samples of mineral ore has been demonstrated. The literature registers only the application of the fission track technique to mineral ore in the case where the fissionable element is uranium. The technique was applied to determine the thorium concentration of an ore sample from Morro do Ferro, taking advantage of the high thorium to uranium ratio in that mineral. The sample analysed presented a thorium concentration of 2467 +- 400 mg Th/Kg ore. The so called wet method was adopted by using the Bayer made Makrofol KG 10μm thick, as the detector foil, immersed in the thorium solution. The technique is also useful to determine thorium concentrations in environmental samples because of the following aspects: high sensitivity; fast chemical separation of interfering elements; low cost; and operational simplicity. (Author) [pt

Mobile Augmented Reality Support for Architects based on feature Tracking Techniques

DEFF Research Database (Denmark)

Grønbæk, Kaj; Nielsen, Mikkel Bang; Kramp, Gunnar

2004-01-01

This paper presents a mobile Augmented Reality (AR) system called the SitePack supporting architects in visualizing 3D models in real-time on site. We describe how vision based feature tracking techniques can help architects making decisions on site concerning visual impact assessment. The AR sys...

Start-up analysis of INET-5 MW district heating prototype reactor

International Nuclear Information System (INIS)

Li Tianshu

1991-09-01

The main features and thermohydraulic design parameters of the INET-5 MW reactor (INET: Institute of Nuclear Technology of Tsinghua University, Beijing) are presented. The start-up process and the effect of thermohydraulic instability on start-up process have been analyzed. The main obstacle of start-up process of INET-5 MW reactor is to pass the instability region from 1 atm to normal operation condition. For avoiding instability, the start-up process should be divided into two steps. The results of three different start-up proposals calculated by DACOL code are given and compared. The possibility of instabilities for each proposal has been checked. The checked results show that there is no instability during start-up of the three proposals. So, it is supposed that the INET-5 MW reactor can safely and stably reach the operation conditions. Finally, some conclusions about the effect of instability on start-up in boiling mode of INET-5MW reactor are given

Impact of entrepreneurship policies on opportunity to startup

Directory of Open Access Journals (Sweden)

Ali Davari

2017-09-01

Full Text Available During the previous decades, policy makers have formulated policies for developing entrepreneurship in different countries in order to decrease unemployment and poverty toward sustainable development. Some of these policies include encouraging people to be an entrepreneur, opportunity creation, educating new skills to entrepreneurs and so on. In recent years an appropriate context has been formed for entrepreneurship development in Iran and some programs have been executed. Therefore, formulating appropriate frameworks to guide Iranian government in this way is a necessity. This paper evaluates the impact of entrepreneurship policies on opportunity to startup in Iran. The results of path analysis indicate that supportive financial and non-financial actions influence positively on opportunity to startup. In addition, education and culture also influence positively on opportunity to startup. Finally, legislation also positively influences on opportunity to startup.

An analysis of the sliding pressure start-up of SCWR

International Nuclear Information System (INIS)

Wang, F.; Yang, J.; Li, H.; Zhang, Y.; Zhang, J.; Shan, J.; Gou, J.; Zhang, B.; Chen, C.

2012-01-01

In this paper, the preliminary sliding pressure start-up system and scheme of supercritical water-cooled reactor in CGNPC (CGN-SCWR) were proposed. Thermal-hydraulic behavior in start-up procedures was analyzed in detail by employing advanced reactor subchannel analysis software ATHAS. The maximum cladding temperature (MCT for short) and core power of fuel assembly during the whole start-up process were investigated comparatively. The results show that the recommended start-up scheme meets the design requirements from the perspective of thermal-hydraulic. (authors)

Control device for start-up of reactor depressurization system

International Nuclear Information System (INIS)

Suzuki, Hiroshi; Saito, Minoru; Oda, Shingo; Miura, Satoshi; Hashimoto, Koji; Tate, Hitoshi; Fujii, Kazunobu

1998-01-01

The present invention concerns are emergency reactor core cooling system (ECCS) of a BWR type reactor and provides a control device for start-up of an automatic depressurization system. Namely, the device has an object of preventing erroneous opening of a main steam escape safety value when testing a start-up signal circuit of an automatic depressurization system for testing the automatic depressurization system. A start-up signal circuit receives both signals of a reactor container pressure high signal and a reactor pressure vessel water level low signal and outputs an automatic start-up signal for compulsorily opening a main steam escape safety valve automatically. A test switch having a self-holding circuit is disposed to a central control chamber. A test signal circuit is disposed for preventing transfer of an erroneous start-up signal to the main steam escape safety valve due to a simulation signal during output test signals by the test switch. (I.S.)

Determination of the uranium concentration in soil solutions by the fission track registration technique

International Nuclear Information System (INIS)

Fernandes, G.P.

1980-02-01

The fission tracks registration technique was used to determine the uranium concentration in soil solutions. The Makrofol KG, a synthetic plastic manufactured by Bayer, was used as a detector and the wet method was applied. From the calibration curves obtained, it was possible to determine uranium concentrations in soil solutions, from 90 to 320 μg U/l, with an error between 9.4% and 4.0%, respectively. The method was applied to a few soil samples from Pocos de Caldas, Minas Gerais in Brazil. The uranium concentrations in the sample and residues were also determined by other methods to compare the results obtained; only one sample showed deviation from the results obtained by the fission tracks method. And this discrepancy was explained in a reasonable way. It was shown that the fission tracks technique can be used with sucess for application in soil solutions. (Author) [pt

RF front-end world class designs

CERN Document Server

Love, Janine

2009-01-01

All the design and development inspiration and direction a harware engineer needs in one blockbuster book! Janine Love site editor for RF Design Line,columnist, and author has selected the very best RF design material from the Newnes portfolio and has compiled it into this volume. The result is a book covering the gamut of RF front end design from antenna and filter design fundamentals to optimized layout techniques with a strong pragmatic emphasis. In addition to specific design techniques and practices, this book also discusses various approaches to solving RF front end design problems and h

Hazard and operability study (Haz Op) of the 2 MW IEA-R1 reactor startup procedures

International Nuclear Information System (INIS)

Sauer, Maria E.L.J.; Correa, Francisco; Sara Neto, Antonio J.; Costa, Carlos A.R. da; Santos, Cilas C. dos; Cardenas, Jose P.N.; Berretta, Jose R.; Neves Conti, Thadeu das

1997-01-01

This work presents the Hazard and Operability Study (Haz Op) applied to startup procedures of the 2 MW IEA-R1 research reactor, at IPEN/CNEN-S P. The Haz Op was developed by reviewing the procedures of the installation startup, in order to identify hazards and/or operational problems caused by deviations in the execution of these routines. This paper summarizes this study. describing some potential problems of relevant importance to safety as well as preventives and/or correctives measures to avoid their occurrence. Besides, an benefits evaluation and the technique limitations is made. (author). 5 refs., 1 tab

5-D interpolation with wave-front attributes

Science.gov (United States)

Xie, Yujiang; Gajewski, Dirk

2017-11-01

Most 5-D interpolation and regularization techniques reconstruct the missing data in the frequency domain by using mathematical transforms. An alternative type of interpolation methods uses wave-front attributes, that is, quantities with a specific physical meaning like the angle of emergence and wave-front curvatures. In these attributes structural information of subsurface features like dip and strike of a reflector are included. These wave-front attributes work on 5-D data space (e.g. common-midpoint coordinates in x and y, offset, azimuth and time), leading to a 5-D interpolation technique. Since the process is based on stacking next to the interpolation a pre-stack data enhancement is achieved, improving the signal-to-noise ratio (S/N) of interpolated and recorded traces. The wave-front attributes are determined in a data-driven fashion, for example, with the Common Reflection Surface (CRS method). As one of the wave-front-attribute-based interpolation techniques, the 3-D partial CRS method was proposed to enhance the quality of 3-D pre-stack data with low S/N. In the past work on 3-D partial stacks, two potential problems were still unsolved. For high-quality wave-front attributes, we suggest a global optimization strategy instead of the so far used pragmatic search approach. In previous works, the interpolation of 3-D data was performed along a specific azimuth which is acceptable for narrow azimuth acquisition but does not exploit the potential of wide-, rich- or full-azimuth acquisitions. The conventional 3-D partial CRS method is improved in this work and we call it as a wave-front-attribute-based 5-D interpolation (5-D WABI) as the two problems mentioned above are addressed. Data examples demonstrate the improved performance by the 5-D WABI method when compared with the conventional 3-D partial CRS approach. A comparison of the rank-reduction-based 5-D seismic interpolation technique with the proposed 5-D WABI method is given. The comparison reveals that

Decision Enhancement Services for Small and Medium Enterprise Start-Ups in Uganda

NARCIS (Netherlands)

Sol, H G; Basaza, Habinka; Sprague, Ralph H.

2012-01-01

While start-up firms create a substantial economic impact on most economies, the failure rate of start-up firms seems to remain high due to inadequate agile decision services. Deciding to start-up mining Small and Medium Enterprises (SME) is a challenging task in Uganda. Research on SME start-up

Automated start-up of EBR-II

International Nuclear Information System (INIS)

Kisner, R.A.

1989-01-01

Oak Ridge National Laboratory (ORNL) and Argonne National Laboratory (ANL) are undertaking a joint project to develop control philosophies, strategies, and algorithms for computer control of the start-up mode of the Experimental Breeder Reactor II (EBR-II). The major objective of this project is to show that advanced liquid-metal reactor (LMR) plants can be operated from low power to full power using computer control. Development of an automated control system with this objective in view will help resolve specific issues and provide proof through demonstration that automatic control for plant start-up is feasible. This paper describes the approach that will be used to develop such a system and some of the features it is expected to have. Structured, rule-based methods, which will provide start-up capability from a variety of initial plant conditions and degrees of equipment operability, will be used for accomplishing mode changes during plant start-up. Several innovative features will be incorporated such as signal, command, and strategy validation to maximize reliability, flexibility to accommodate a wide range of plant conditions, and overall utility. Continuous control design will utilize figures of merit to evaluate how well the controller meets the mission requirements. The operator interface will have unique ''look ahead'' features to let the operator see what will happen next. 15 refs., 7 figs., 1 tab

Strategies, Uncertainty and Performance of Small Business Startups

NARCIS (Netherlands)

A.M. van Gelderen (Marco); M. Frese (Michael); A.R. Thurik (Roy)

2000-01-01

textabstractPersonal strategies of owners/founders of small business startups are related to performance and to environmental uncertainty. This is done using a longitudinal data set of some 50 Dutch startups. The results suggest a dynamic process between strategy and performance. A discrimination is

TIBER engineering test reactor (ETR) startup scenarios

International Nuclear Information System (INIS)

Blackfield, D.T.; Perkins, L.J.

1987-01-01

A time-dependent Tokamak Systems Code (TTSC) has been developed and used to examine various inductively driven startup scenarios for the TIBER reactor. Radially averaged particle and energy balance equations are solved. In addition, time varying currents in the PF and OH coils are determined from MHD equilibrium and volt-seconds considerations. Less than 20 MW of auxiliary power deposited in the electrons is required to obtain steady-state operations. For this scenario, less than 10% of the total volt-seconds capability is consumed during startup and the currents in the PF and OH coils do not appear to exceed stress limits. For every volt-second saved during startup, the burn time can be extended 14 seconds. 4 refs., 6 figs., 3 tabs

A Wireless Sensor Network with Soft Computing Localization Techniques for Track Cycling Applications.

Science.gov (United States)

Gharghan, Sadik Kamel; Nordin, Rosdiadee; Ismail, Mahamod

2016-08-06

In this paper, we propose two soft computing localization techniques for wireless sensor networks (WSNs). The two techniques, Neural Fuzzy Inference System (ANFIS) and Artificial Neural Network (ANN), focus on a range-based localization method which relies on the measurement of the received signal strength indicator (RSSI) from the three ZigBee anchor nodes distributed throughout the track cycling field. The soft computing techniques aim to estimate the distance between bicycles moving on the cycle track for outdoor and indoor velodromes. In the first approach the ANFIS was considered, whereas in the second approach the ANN was hybridized individually with three optimization algorithms, namely Particle Swarm Optimization (PSO), Gravitational Search Algorithm (GSA), and Backtracking Search Algorithm (BSA). The results revealed that the hybrid GSA-ANN outperforms the other methods adopted in this paper in terms of accuracy localization and distance estimation accuracy. The hybrid GSA-ANN achieves a mean absolute distance estimation error of 0.02 m and 0.2 m for outdoor and indoor velodromes, respectively.

Application of a novel new multispectral nanoparticle tracking technique

Science.gov (United States)

McElfresh, Cameron; Harrington, Tyler; Vecchio, Kenneth S.

2018-06-01

Fast, reliable, and accurate particle size analysis techniques must meet the demands of evolving industrial and academic research in areas of functionalized nanoparticle synthesis, advanced materials development, and other nanoscale enabled technologies. In this study a new multispectral particle tracking analysis (m-PTA) technique enabled by the ViewSizer™ 3000 (MANTA Instruments, USA) was evaluated using solutions of monomodal and multimodal gold and polystyrene latex nanoparticles, as well as a spark eroded polydisperse 316L stainless steel nanopowder, and large (non-Brownian) borosilicate particles. It was found that m-PTA performed comparably to the DLS in evaluation of monomodal particle size distributions. When measuring bimodal, trimodal and polydisperse solutions, the m-PTA technique overwhelmingly outperformed traditional dynamic light scattering (DLS) in both peak detection and relative particle concentration analysis. It was also observed that the m-PTA technique is less susceptible to large particle overexpression errors. The ViewSizer™ 3000 was also found to be successful in accurately evaluating sizes and concentrations of monomodal and bimodal sinking borosilicate particles.

Nuclear plant startup support problems experienced by B and W

International Nuclear Information System (INIS)

Spangler, W.H.; Phinney, J.D.

1976-01-01

There have now been enough nuclear power plants brought on line for the industry to recognize some of the problems that will occur during startup. Schedules are not being met; startup costs to both the utilities and the suppliers are excessive and unpredictable, and in some cases reliability has suffered. Manpower planning is difficult at best. Earlier and more accurate scheduling and planning are the most significant candidates for improvement. Greater attention to the startup organization and how it is to function is also a key. The organization should probably be designed with the specific startup task in mind

Intellectual property and financing strategies for technology startups

CERN Document Server

Halt, Jr , Gerald B; Stiles, Amber R; Fesnak, Robert

2017-01-01

This book offers a comprehensive, easy to understand guide for startup entities and developing companies, providing insight on the various sources of funding that are available, how these funding sources are useful at each stage of a company’s development, and offers a comprehensive intellectual property strategy that parallels each stage of development. The IP strategies offered in this book take into consideration the goals that most startups and companies have at each stage of development, as well as the limitations that exist at each stage (i.e., limited available resources earmarked for intellectual property asset development), and provides solutions that startups and companies can implement to maximize their return on intellectual property investments. This book also includes a number of descriptive examples, case studies and scenarios to illustrate the topics discussed, and is intended for use by startups and companies across all industries. Readers will garner an appreciation for the value that inte...

Software development methodologies and practices in startups:systematic literature review

OpenAIRE

Tegegne, E. (Esubalew)

2018-01-01

Abstract Startups are newly created companies with little or no operating history and with limited resources and markets. Software startup are aiming to develop cutting edge software products under highly uncertain conditions, overcoming fast-growing markets under multiple influences. The significance of startups for economic development is growing in software business due to their ability to quickly create innovative techn...

Internetové start-up projekty a jejich rizika

OpenAIRE

Sládek, Pavel

2014-01-01

The goal of this thesis is to analyse the field of the Internet startups and to find out what trends and risks are associated with their development and launching. The first chapter of this thesis summarizes the main changes in recent years and the methodologies that are the most often used in developing of startups. The work also reflects a problem connected with financing, such as investor interest in emerging projects. Then there is explained how startup investing works and what opportunit...

Product innovation and commercialization in lean global start-ups

DEFF Research Database (Denmark)

Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

2015-01-01

The paper examines the distinctive characteristics of product innovation and commercialization in Lean Global Start-up (LGS) – new technology firms which have adopted a lean and global path from or near to their inception. It suggests an uncertainty vs risk framework which allows integrating two...... research streams – Born Global (BG) firms and lean start-ups. In addition to its integrative theoretical value, the paper offers insights for lean start-up managers dealing with the challenges of a global start....

Automatic start-up system of nuclear reactor based on sequence control technology

International Nuclear Information System (INIS)

Zhang Yao; Zhang Dafa; Peng Huaqing

2009-01-01

A conceptive design of an automatic start-up system based on the sequence control for the nuclear reactors is given in this paper, so as to solve the problems during the start-up process, such as the long operation time, low automatic control level and high accident rate. The start-up process and its requirements are analyzed in detail at first. Then,the principle, the architecture, the key technologies of the automatic start-up system of nuclear reactors are designed and discussed. With the designed system, the automatic start-up of the nuclear reactor can be realized,the work load of the operator can be reduced,and the safety and efficiency of the nuclear power plant during its start-up can be improved. (authors)

Start-up of NPP Krsko; Pokusno obratovanje NE Krsko

Energy Technology Data Exchange (ETDEWEB)

Spiler, J; Aralica, J [Nuklearna elektrana Krsko, Krsko (Yugoslavia)

1984-07-01

The report describes a review of start-up program and its realisation. There are also described some more significant start-up results with their evaluation. The most significant operation criteria are compared between NPP Krsko and other similar plants in the world. The comparison shows that after the first contractors and operation personnel efforts have been accomplished, our first nuclear power plant is a safe and reliable source of electric power. At the end there are listed NPP Krsko start-up recommendations and experience. (author)

Solvent Front Position Extraction procedure with thin-layer chromatography as a mode of multicomponent sample preparation for quantitative analysis by instrumental technique.

Science.gov (United States)

Klimek-Turek, A; Sikora, E; Dzido, T H

2017-12-29

A concept of using thin-layer chromatography to multicomponent sample preparation for quantitative determination of solutes followed by instrumental technique is presented. Thin-layer chromatography (TLC) is used to separate chosen substances and their internal standard from other components (matrix) and to form a single spot/zone containing them at the solvent front position. The location of the analytes and internal standard in the solvent front zone allows their easy extraction followed by quantitation by HPLC. Copyright © 2017 Elsevier B.V. All rights reserved.

40 CFR 65.6 - Startup, shutdown, and malfunction plan and procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Startup, shutdown, and malfunction... (CONTINUED) AIR PROGRAMS (CONTINUED) CONSOLIDATED FEDERAL AIR RULE General Provisions § 65.6 Startup... Group 2A or Group 2B process vents. (b) Startup, shutdown, and malfunction plan—(1) Description and...

Open innovation and the comparison between startups and incumbent firms in Spain

DEFF Research Database (Denmark)

Gimenez Fernandez, Elena Maria; Beukel, Karin

2017-01-01

This study compares the open innovation strategy between startups and incumbent firms over a period of ten years (2004-2013). Using a sample of startups and incumbent Spanish firms, we find that they differ considerably, and that this has implications for management. Incumbent firms and startups...... differ in terms of their use of external cooperation activities as a source of innovation. The lack of financial and human resources of startups leads them to open their borders more than incumbent firms, and startups benefit from being flexible, as they have yet to implement routines. This boosts...... startups’ innovation performance....

Dynamics and Control During Start-Up of Energy Integrated Distillation Column

DEFF Research Database (Denmark)

of the inherent effects of process integration upon a start-up procedure. In particular the effect of energy recycle upon the possible start-up sequence, and the effect of using an actuator for control purposes, i.e. the heat pump, which in itself requires significant start-up time. The experimental application...

Effect of non-condensable gas on startup of a loop thermosyphon

International Nuclear Information System (INIS)

He, Jiang; Lin, Guiping; Bai, Lizhan; Miao, Jianyin; Zhang, Hongxing; Wang, Lu

2013-01-01

Non-condensable gas (NCG) generated inside two-phase heat transfer devices can adversely affect the thermal performance and limit the lifetime of such devices. In this work, experimental investigation of the effect of NCG on the startup of an ammonia-stainless steel loop thermosyphon was conducted. In the experiment, nitrogen was injected into the loop thermosyphon as NCG. The effect of NCG inventory on the startup behavior was investigated by adjusting the injected amount of nitrogen. The experimental results reveal that NCG prolongs the startup time and increases the startup liquid superheat and temperature overshoot; the more NCG exists in the loop thermosyphon, the higher the liquid superheat and temperature overshoot. When NCG is present in the system, boiling usually occurs in the evaporator before startup, but it does not mean the system will start up instantly, which differs from the conditions without NCG. Under all the conditions, increasing the heat load can effectively shorten the startup time but leads to a large temperature overshoot; forced convection cooling of the condenser has almost no effect on shortening the startup time especially for large NCG inventory situations, but it can effectively limit the temperature overshoot. For large NCG inventory situations, the loop thermosyphon can start up at a small heat load (5 W) or even without a heat load when the condenser is cooled by forced convection of ethanol. No failed start-ups occurred during any of the tests. (authors)

Startup analysis for a high temperature gas loaded heat pipe

Science.gov (United States)

Sockol, P. M.

1973-01-01

A model for the rapid startup of a high-temperature gas-loaded heat pipe is presented. A two-dimensional diffusion analysis is used to determine the rate of energy transport by the vapor between the hot and cold zones of the pipe. The vapor transport rate is then incorporated in a simple thermal model of the startup of a radiation-cooled heat pipe. Numerical results for an argon-lithium system show that radial diffusion to the cold wall can produce large vapor flow rates during a rapid startup. The results also show that startup is not initiated until the vapor pressure p sub v in the hot zone reaches a precise value proportional to the initial gas pressure p sub i. Through proper choice of p sub i, startup can be delayed until p sub v is large enough to support a heat-transfer rate sufficient to overcome a thermal load on the heat pipe.

Cold start-up condition model for heat recovery steam generators

International Nuclear Information System (INIS)

Sindareh-Esfahani, Peyman; Habibi-Siyahposh, Ehsan; Saffar-Avval, Majid; Ghaffari, Ali; Bakhtiari-Nejad, Firooz

2014-01-01

A dynamic modeling of Heat Recovery Steam Generator (HRSG) during cold start-up operation in Combined Cycle Power Plant (CCPP) is introduced. In order to characterize the essential dynamic behavior of the HRSG during cold start-up; Dynamic equations of all HRSG's components are developed based on energy and mass balances. To describe precisely the operation of HRSG; a method based on nonlinear estimated functions for thermodynamic properties is applied to estimate the model parameters. Model parameters are evaluated by a designed algorithm based on Genetic Algorithm (GA). A wide set of experimental data is used to validate HRSG model during cold start-up operation. The simulation results show the reliability and validity of the developed model for cold start-up operation. - Highlights: •Presenting a mathematical model for HRSGs cold start-up based on energy and mass balances. •A designed parameter identification algorithm based on GA is presented. •Application of experimental data in order to model and validate simulation results

University Knowledge Spillovers & Regional Start-up Rates

DEFF Research Database (Denmark)

Hellerstedt, Karin; Wennberg, Karl; Frederiksen, Lars

2014-01-01

how characteristics of the economic and political milieu within each region influence the ratio of firm births. We find that knowledge spillovers from universities and firm-based R&D strongly affect the start-up rates for both high-tech firms and knowledge-intensive services firms. Further, the start......This chapter investigates how regional start-up rates in the knowledge-intensive services and high-tech industries are influenced by knowledge spillovers from both universities and firm-based R&D activities. Integrating insights from economic geography and organizational ecology into the literature......-up rate of knowledge-intensive service firms is tied more strongly to the supply of university educated individuals and the political regulatory regime within the municipality than start-ups in high-tech industries. This suggests that knowledge-intensive service-start-ups are more susceptible to both...

Two-dimensional tracking of a motile micro-organism allowing high-resolution observation with various imaging techniques

International Nuclear Information System (INIS)

Oku, H.; Ogawa, N.; Ishikawa, M.; Hashimoto, K.

2005-01-01

In this article, a micro-organism tracking system using a high-speed vision system is reported. This system two dimensionally tracks a freely swimming micro-organism within the field of an optical microscope by moving a chamber of target micro-organisms based on high-speed visual feedback. The system we developed could track a paramecium using various imaging techniques, including bright-field illumination, dark-field illumination, and differential interference contrast, at magnifications of 5 times and 20 times. A maximum tracking duration of 300 s was demonstrated. Also, the system could track an object with a velocity of up to 35 000 μm/s (175 diameters/s), which is significantly faster than swimming micro-organisms

An enhanced tokamak startup model

Science.gov (United States)

Goswami, Rajiv; Artaud, Jean-François

2017-01-01

The startup of tokamaks has been examined in the past in varying degree of detail. This phase typically involves the burnthrough of impurities and the subsequent rampup of plasma current. A zero-dimensional (0D) model is most widely used where the time evolution of volume averaged quantities determines the detailed balance between the input and loss of particle and power. But, being a 0D setup, these studies do not take into consideration the co-evolution of plasma size and shape, and instead assume an unchanging minor and major radius. However, it is known that the plasma position and its minor radius can change appreciably as the plasma evolves in time to fill in the entire available volume. In this paper, an enhanced model for the tokamak startup is introduced, which for the first time takes into account the evolution of plasma geometry during this brief but highly dynamic period by including realistic one-dimensional (1D) effects within the broad 0D framework. In addition the effect of runaway electrons (REs) has also been incorporated. The paper demonstrates that the inclusion of plasma cross section evolution in conjunction with REs plays an important role in the formation and development of tokamak startup. The model is benchmarked against experimental results from ADITYA tokamak.

Dynamics and Control During Start-up of Energy Integrated Distillation Column

DEFF Research Database (Denmark)

Eden, Mario Richard; Koggersbøl, Arne; Hallager, L.

2000-01-01

of the inherent effects of process integration upon a start-up procedure. In particular the effect of energy recycle upon the possible start-up sequence, and the effect of using an actuator f or control purposes, i.e. the heat pump, which in itself requires significant start-up time. The experimental application...

78 FR 73753 - Partnerships; Start-Up Expenditures; Organization and Syndication Fees

Science.gov (United States)

2013-12-09

... deduct start-up expenditures in the taxable year in which the active trade or business begins. The amount... begins. All start-up expenditures that relate to the active trade or business are considered in...(b) to amortize start-up expenditures for the taxable year in which the active trade or business to...

Startup method for natural convection type nuclear reactor

International Nuclear Information System (INIS)

Utsuno, Hideaki.

1993-01-01

In a nuclear reactor started by natural convection, no sufficient stability margin can be ensured upon start up. Then, in the present invention, a deaerating operation is conducted before start-up of the reactor, then control rods are withdrawn after conducting the deaerating operation and temperature and pressure are raised by nuclear heating, to obtain a rated power. As a result, reactor power and subcooling at the inlet of the reactor core are within a range of lower than a geysering forming region, thereby enabling to prevent occurence of geysering inherent to the start-up of operation in a natural convection state, shorten the start-up time, as well as remove oxygen dissolved in coolants. (N.H.)

Startup of a high-temperature reactor cooled and moderated by supercritical-pressure light water

International Nuclear Information System (INIS)

Yi, Tin Tin; Ishiwatari, Yuki; Koshizuka, Seiichi; Oka, Yoshiaki

2003-01-01

The startup schemes of high-temperature reactors cooled and moderated by supercritical pressure light water (SCLWR-H) with square lattice and descending flow type water rods are studied by thermal-hydraulic analysis. In this study, two kinds of startup systems are investigated. In the constant pressure startup system, the reactor starts at a supercritical pressure. A flash tank and pressure reducing valves are necessary. The flash tank is designed so that the moisture content in the steam is less than 0.1%. In sliding pressure startup system, the reactor starts at a subcritical pressure. A steam-water separator and a drain tank are required for two-phase flow at startup. The separator is designed by referring to the water separator used in supercritical fossil-fired power plants. The maximum cladding surface temperature during the power-raising phase of startup is restricted not to exceed the rated value of 620degC. The minimum feedwater flow rate is 25% for constant pressure startup and 35% for sliding pressure startup system. It is found that both constant pressure startup system and sliding pressure startup system are feasible in SCLWR-H from the thermal hydraulic point of view. The core outlet temperature as high as 500degC can be achieved in the present design of SCLWR-H. Since the feedwater flow rate of SCLWR-H (1190 kg/s) is lower than that of the previous SCR designs the weight of the component required for startup is reduced. The sliding pressure startup system is better than constant pressure startup system in order to reduce the required component weight (and hence material expenditure) and to simplify the startup plant system. (author)

MUON POLARIZATION EFFECTS IN THE FRONT END OF THE NEUTRINO FACTORY

International Nuclear Information System (INIS)

FERNOW, R.C.; GALLARDO, J.C.; FUKUI, Y.

2000-01-01

The authors summarize the methods used for simulation of polarization effects in the front end of a possible neutrino factory. They first discuss the helicity of muons in the pion decay process. They find that, neglecting acceptance considerations, the average helicity asymptotically approaches a magnitude of 0.185 at large pion momenta. Next they describe the methods used for tracking the spin through the complicated electromagnetic field configurations in the front end of the neutrino factory, including rf phase rotation and ionization cooling channels. Various depolarizing effects in matter are then considered, including multiple Coulomb scattering and elastic scattering from atomic electrons. Finally, they include all these effects in a simulation of a 480 m long, double phase rotation front end scenario

Start-Up Funding Intentions Among Nascent Nonprofit Entrepreneurs: An Exploratory Investigation

Directory of Open Access Journals (Sweden)

Fredrik O. Andersson

2018-04-01

Full Text Available This paper explores the start-up funding intentions of nascent nonprofit entrepreneurs, i.e., individuals in the process of creating a new formal nonprofit organization. The main questions being examined are from which sources nascent nonprofit entrepreneurs anticipate to obtain start-up funding from, how much start-up funding nascent nonprofit entrepreneurs anticipate they will need to formally launch their new nonprofit, and if there are any differences in funding intentions among nascent nonprofit entrepreneurs with and without previous start-up experience. The results from a survey of 103 nascent nonprofit entrepreneurs in Kansas City are presented and contrasted with existing research on funding of new nonprofit organizations. The results show an apparent preference for start-up funding from philanthropic grants and private donations, along with personal contributions of the founder(s.

Plasma startup patterns in tokamak reactors

International Nuclear Information System (INIS)

Maki, Koichi; Tone, Tatsuzo.

1983-01-01

Plasma startup patterns are studied from the viewpoint of net power loss represented by the total power loss less the α-particle heating power. The existence is shown of a critical temperature of plasma at which the net power loss becomes independent of plasma density. Observations are made which indicate that the net power loss decreases with lowering plasma density in the range below the critical temperature and vice versa, whether governed by empirical or trapped-ion scaling laws. A startup pattern is presented which minimizes the net power loss during startup, and which prescribes that: (1) The plasma density should be kept as low as possible until the plasma is heated up to the critical temperature; (2) thereafter, the plasma density should be increased to its steady state value while retaining the critical temperature; and (3) finally, with the density kept constant, the temperature should be further raised to its steady state value. The net power loss at critical temperature represents the lower limit of heating power required to bring the plasma to steady state in tokamak reactors. (author)

Startup Report for Ground Water Extraction, Treatment, and Recharge System

National Research Council Canada - National Science Library

Lamb, Steve

1997-01-01

The document presents startup procedures, observations and measurements conducted during the startup of the Groundwater Extraction, Treatment and Recharge System, built for the 162nd Fighter Wing, Air...

Pareto fronts in clinical practice for pinnacle.

Science.gov (United States)

Janssen, Tomas; van Kesteren, Zdenko; Franssen, Gijs; Damen, Eugène; van Vliet, Corine

2013-03-01

Our aim was to develop a framework to objectively perform treatment planning studies using Pareto fronts. The Pareto front represents all optimal possible tradeoffs among several conflicting criteria and is an ideal tool with which to study the possibilities of a given treatment technique. The framework should require minimal user interaction and should resemble and be applicable to daily clinical practice. To generate the Pareto fronts, we used the native scripting language of Pinnacle(3) (Philips Healthcare, Andover, MA). The framework generates thousands of plans automatically from which the Pareto front is generated. As an example, the framework is applied to compare intensity modulated radiation therapy (IMRT) with volumetric modulated arc therapy (VMAT) for prostate cancer patients. For each patient and each technique, 3000 plans are generated, resulting in a total of 60,000 plans. The comparison is based on 5-dimensional Pareto fronts. Generating 3000 plans for 10 patients in parallel requires on average 96 h for IMRT and 483 hours for VMAT. Using VMAT, compared to IMRT, the maximum dose of the boost PTV was reduced by 0.4 Gy (P=.074), the mean dose in the anal sphincter by 1.6 Gy (P=.055), the conformity index of the 95% isodose (CI(95%)) by 0.02 (P=.005), and the rectal wall V(65 Gy) by 1.1% (P=.008). We showed the feasibility of automatically generating Pareto fronts with Pinnacle(3). Pareto fronts provide a valuable tool for performing objective comparative treatment planning studies. We compared VMAT with IMRT in prostate patients and found VMAT had a dosimetric advantage over IMRT. Copyright © 2013 Elsevier Inc. All rights reserved.

Pareto Fronts in Clinical Practice for Pinnacle

International Nuclear Information System (INIS)

Janssen, Tomas; Kesteren, Zdenko van; Franssen, Gijs; Damen, Eugène; Vliet, Corine van

2013-01-01

Purpose: Our aim was to develop a framework to objectively perform treatment planning studies using Pareto fronts. The Pareto front represents all optimal possible tradeoffs among several conflicting criteria and is an ideal tool with which to study the possibilities of a given treatment technique. The framework should require minimal user interaction and should resemble and be applicable to daily clinical practice. Methods and Materials: To generate the Pareto fronts, we used the native scripting language of Pinnacle 3 (Philips Healthcare, Andover, MA). The framework generates thousands of plans automatically from which the Pareto front is generated. As an example, the framework is applied to compare intensity modulated radiation therapy (IMRT) with volumetric modulated arc therapy (VMAT) for prostate cancer patients. For each patient and each technique, 3000 plans are generated, resulting in a total of 60,000 plans. The comparison is based on 5-dimensional Pareto fronts. Results: Generating 3000 plans for 10 patients in parallel requires on average 96 h for IMRT and 483 hours for VMAT. Using VMAT, compared to IMRT, the maximum dose of the boost PTV was reduced by 0.4 Gy (P=.074), the mean dose in the anal sphincter by 1.6 Gy (P=.055), the conformity index of the 95% isodose (CI 95% ) by 0.02 (P=.005), and the rectal wall V 65 Gy by 1.1% (P=.008). Conclusions: We showed the feasibility of automatically generating Pareto fronts with Pinnacle 3 . Pareto fronts provide a valuable tool for performing objective comparative treatment planning studies. We compared VMAT with IMRT in prostate patients and found VMAT had a dosimetric advantage over IMRT

Improved Discretization of Grounding Lines and Calving Fronts using an Embedded-Boundary Approach in BISICLES

Science.gov (United States)

Martin, D. F.; Cornford, S. L.; Schwartz, P.; Bhalla, A.; Johansen, H.; Ng, E.

2017-12-01

Correctly representing grounding line and calving-front dynamics is of fundamental importance in modeling marine ice sheets, since the configuration of these interfaces exerts a controlling influence on the dynamics of the ice sheet. Traditional ice sheet models have struggled to correctly represent these regions without very high spatial resolution. We have developed a front-tracking discretization for grounding lines and calving fronts based on the Chombo embedded-boundary cut-cell framework. This promises better representation of these interfaces vs. a traditional stair-step discretization on Cartesian meshes like those currently used in the block-structured AMR BISICLES code. The dynamic adaptivity of the BISICLES model complements the subgrid-scale discretizations of this scheme, producing a robust approach for tracking the evolution of these interfaces. Also, the fundamental discontinuous nature of flow across grounding lines is respected by mathematically treating it as a material phase change. We present examples of this approach to demonstrate its effectiveness.

Technique for finding and identifying filters that cut off OTDR lights in front of ONU from a central office

Science.gov (United States)

Takaya, Masaaki; Honda, Hiroyasu; Narita, Yoshihiro; Yamamoto, Fumihiko; Arakawa, Koji

2006-04-01

We report on a newly developed in-service measurement technique that can be used from a central office to find and identify any filter in front of an ONU on an optical fiber access network. Using this system, in-service tests can be performed because the test lights are modulated at a high frequency. Moreover, by using the equipment we developed, this confirmation operation can be performed continuously and automatically with existing automatic fiber testing systems. The developed technique is effective for constructing a fiber line testing system with an optical time domain reflectometer.

The Lean and Global Start-up

DEFF Research Database (Denmark)

Tanev, Stoyan; Rasmussen, Erik Stavnsager

For several decades researchers have studied start-up companies with a focus on international markets, suppliers and networks from their inception and on companies that are establishing new, agile business models. This has resulted in two streams of research: The Born Global and International New...... Ventures research and research with a focus on the Lean Start-up company. It is our intention in this paper to give a short presentation of the two research streams and show how they can be merged into one with a focus on newly established technology oriented firms that are lean and global from...

Startup operation of Browns Ferry's 1152-MW nuclear units

International Nuclear Information System (INIS)

Calhoun, J.R.; Green, H.J.; Beers, R.B.

1975-01-01

An overview is presented of startup operation for the Browns Ferry-1 reactor, and comparisons are made with the startup of Browns Ferry-2. Included are comments on the selection of the BWR type steam supply system, reactor fueling, problems encountered, and plant availability

Agile metodologies use for software development in Slovenian start-ups

OpenAIRE

Kašnik, Matic

2014-01-01

The thesis presents and describes the use of agile methodologies which are being used by Slovenian tech start-up companies. It describes the basic features, advantages and disadvantages of various agile methodologies such as Scrum, extreme programming, lean start-up and method Kanban. We made a review of the most used agile methodologies in Slovenian technology start-up companies. In particular, we focus on variety of tools, technics and approaches used by the development teams and where do t...

The Rationality and Irrationality of Financing Green Start-Ups

Directory of Open Access Journals (Sweden)

Linda Bergset

2015-11-01

Full Text Available Green start-ups contribute towards a transition to a more sustainable economy by developing sustainable and environmentally friendly innovation and bringing it to the market. Due to specific product/service characteristics, entrepreneurial motivation and company strategies that might differ from that of other start-ups, these companies might struggle even more than usual with access to finance in the early stages. This conceptual paper seeks to explain these challenges through the theoretical lenses of entrepreneurial finance and behavioural finance. While entrepreneurial finance theory contributes to a partial understanding of green start-up finance, behavioural finance is able to solve a remaining explanatory deficit produced by entrepreneurial finance theory. Although some behavioural finance theorists are suggesting that the current understanding of economic rationality underlying behavioural finance research is inadequate, most scholars have not yet challenged these assumptions, which constrict a comprehensive and realistic description of the reality of entrepreneurial finance in green start-ups. The aim of the paper is thus, first, to explore the specifics of entrepreneurial finance in green start-ups and, second, to demonstrate the need for a more up-to-date conception of rationality in behavioural finance theory in order to enable realistic empirical research in this field.

Start-up test of the prototype heavy water reactor 'FUGEN', (1)

International Nuclear Information System (INIS)

Ando, Hideki; Kawahara, Toshio

1982-01-01

The advanced thermal prototype reactor ''Fugen'' is a heavy water-moderated, boiling light water-cooled power reactor with electric output of 165 MW, which has been developed since 1966 as a national project. The start-up test was begun in March, 1978, being scheduled for about one year, and in March, 1979, it passed the final pre-use inspection and began the full scale operation. In this paper, the result of the start-up test of Fugen is reported. From the experience of the start-up test of Fugen, the following matters are important for the execution of start-up test. 1) Exact testing plan and work schedule, 2) the organization to perform the test, 3) the rapid evaluation of test results and the reflection to next testing plan, and 4) the reflection of test results to rated operation, regular inspection and so on. In the testing plan, the core characteristics peculiar to Fugen, and the features of heavy water-helium system, control system and other equipment were added to the contents of the start-up test of BWRs. The items of the start-up test were reactor physics test, plant equipment performance test, plant dynamic characteristic test, chemical and radiation measurement, and combined test. The organization to perform the start-up test, and the progress and the results of the test are reported. (Kako, I.)

RGBD Video Based Human Hand Trajectory Tracking and Gesture Recognition System

Directory of Open Access Journals (Sweden)

Weihua Liu

2015-01-01

Full Text Available The task of human hand trajectory tracking and gesture trajectory recognition based on synchronized color and depth video is considered. Toward this end, in the facet of hand tracking, a joint observation model with the hand cues of skin saliency, motion and depth is integrated into particle filter in order to move particles to local peak in the likelihood. The proposed hand tracking method, namely, salient skin, motion, and depth based particle filter (SSMD-PF, is capable of improving the tracking accuracy considerably, in the context of the signer performing the gesture toward the camera device and in front of moving, cluttered backgrounds. In the facet of gesture recognition, a shape-order context descriptor on the basis of shape context is introduced, which can describe the gesture in spatiotemporal domain. The efficient shape-order context descriptor can reveal the shape relationship and embed gesture sequence order information into descriptor. Moreover, the shape-order context leads to a robust score for gesture invariant. Our approach is complemented with experimental results on the settings of the challenging hand-signed digits datasets and American sign language dataset, which corroborate the performance of the novel techniques.

Management of the interfaces between construction and startup

International Nuclear Information System (INIS)

Anderson, W.R.; Beatty, D.C.

1976-01-01

Many papers have been presented, and many articles published on the various tasks of Nuclear Plant Design, Construction, Startup and Operations. Most of the presentations have been concerned with the complexities of the particular task being discussed. This is as it should be, since these areas are quite broad in themselves and deserve the full attention of the technology. Recently more attention is being directed to the interfaces between the classical portions of nuclear projects. The paper attempts to address just one of these areas: the interfaces between construction and startup. These interfaces have normally been addressed to the extent that engineering schedules, construction schedules, equipment deliveries and startup test schedules have been dovetailed graphically, or computerized, and periodically updated to reflect significant changes

Determination of boron in aqueous solutions by solid state nuclear track detectors technique, using a filtered neutron beam

International Nuclear Information System (INIS)

Moraes, M.A.P.V. de; Pugliesi, R.; Khouri, M.T.F.C.

1985-11-01

The solid state nuclear track detectors technique has been used for determination of boron in aqueous solutions, using a filtered neutron beam. The particles tracks from the 10 B(n,α)Li 7 reaction were registered in the CR-39 film, chemically etched in a (30%) KOH solution 70 0 C during 90 minutes. The obtained results showed the usefulness of this technique for boron determination in the ppm range. The inferior detectable limit was 9 ppm. The combined track registration efficiency factor K has been evaluated in the solutions, for the CR-39 detector and its values is K= (4,60 - + 0,06). 10 -4 cm. (Author) [pt

Automatic Bolus Tracking Versus Fixed Time-Delay Technique in Biphasic Multidetector Computed Tomography of the Abdomen

International Nuclear Information System (INIS)

Adibi, Atoosa; Shahbazi, Ali

2014-01-01

Bolus tracking can individualize time delay for the start of scans in spiral computed tomography (CT). We compared automatic bolus tracking method with fixed time-delay technique in biphasic contrast enhancement during multidetector CT of abdomen. Adult patients referred for spiral CT of the abdomen were randomized into two groups; in group 1, the arterial and portal phases of spiral scans were started 25 s and 55 s after the start of contrast material administration; in group 2, using the automatic bolus tracking software, repetitive monitoring scans were performed within the lumen of the descending aorta as the region of interest with the threshold of starting the diagnostic scans as 60 HU. The contrast enhancement of the aorta, liver, and spleen were compared between the groups. Forty-eight patients (23 males, 25 females, mean age=56.4±13.5 years) were included. The contrast enhancement of the aorta, liver, and spleen at the arterial phase was similar between the two groups (P>0.05). Regarding the portal phase, the aorta and spleen were more enhanced in the bolus-tracking group (P<0.001). The bolus tracking provided more homogeneous contrast enhancement among different patients than the fixed time-delay technique in the liver at portal phase, but not at the arterial phase. The automatic bolus-tracking method, results in higher contrast enhancement of the aorta and spleen at the portal phase, but has no effect on liver enhancement. However, bolus tracking is associated with reduced variability for liver enhancement among different patients

Start-Up Size Strategy and Risk Management: Impact on New Venture Performance

OpenAIRE

André van Stel; Andrew Burke; José Maria Millán; Concepcion Roman

2013-01-01

Start-up size is a key strategic decision for entrepreneurs. Should entrepreneurs start up close to minimum efficient scale or should they take less risks and start-up on a smaller scale? Previously, this strategic decision appeared to be one of simply making a choice between a higher risk/reward larger start-up versus a lower risk/reward smaller scale start-up. However, recent research on the relationship between risk management and performance (Burke, 2009) indicates that in situations of g...

Startup, Shutdown, & Malfunction (SSM) Emissions

Science.gov (United States)

EPA issued a final action to ensure states have plans in place that are fully consistent with the Clean Air Act and recent court decisions concerning startup, shutdown and malfunction (SSM) operations.

A novel method for detecting and counting overlapping tracks in SSNTD by image processing techniques

International Nuclear Information System (INIS)

Ab Azar, N.; Babakhani, A.; Broumandnia, A.; Sepanloo, K.

2016-01-01

Overlapping object detection and counting is a challenge in image processing. A new method for detecting and counting overlapping circles is presented in this paper. This method is based on pattern recognition and feature extraction using “neighborhood values“ in an object image by implementation of image processing techniques. The junction points are detected by assignment of a value for each pixel in an image. As is shown, the neighborhood values for junction points are larger than the values for other points. This distinction of neighborhood values is the main feature which can be utilized to identify the junction points and to count the overlapping tracks. This method can be used for recognizing and counting charged particle tracks, blood cells and also cancer cells. The method is called “Track Counting based on Neighborhood Values” and is symbolized by “TCNV”. - Highlights: • A new method is introduced to recognize nuclear tracks by image processing. • The method is used to specify neighborhood pixels in junction points in overlapping tracks. • Enhanced method of counting overlapping tracks. • New counting system has linear behavior in counting tracks with density less than 300,000 tracks per cm"2. • In the new method, the overlap tracks can be recognized even to 10× tracks and more.

Producing an Assistant Guide for Haaga-Helia StartUp School

OpenAIRE

Averina, Maria

2016-01-01

This product-oriented thesis was commissioned by the StartUp School (SUS), a program of Haaga-Helia University of Applied Sciences that supports Haaga-Helia students to become entrepreneurs. The StartUp School offers Haaga-Helia students a six-month assistant trainee position. Consequently, every half a year there is a new assistant at the StartUp School. The commissioning party was lacking an essential tool to introduce work tasks to new assistant interns. The objective of the thesis was...

Light-Front Quantization of Gauge Theories

Energy Technology Data Exchange (ETDEWEB)

Brodsky, Stanley J.

2003-03-25

Light-front wavefunctions provide a frame-independent representation of hadrons in terms of their physical quark and gluon degrees of freedom. The light-front Hamiltonian formalism provides new nonperturbative methods for obtaining the QCD spectrum and eigensolutions, including resolvant methods, variational techniques, and discretized light-front quantization. A new method for quantizing gauge theories in light-cone gauge using Dirac brackets to implement constraints is presented. In the case of the electroweak theory, this method of light-front quantization leads to a unitary and renormalizable theory of massive gauge particles, automatically incorporating the Lorentz and 't Hooft conditions as well as the Goldstone boson equivalence theorem. Spontaneous symmetry breaking is represented by the appearance of zero modes of the Higgs field leaving the light-front vacuum equal to the perturbative vacuum. I also discuss an ''event amplitude generator'' for automatically computing renormalized amplitudes in perturbation theory. The importance of final-state interactions for the interpretation of diffraction, shadowing, and single-spin asymmetries in inclusive reactions such as deep inelastic lepton-hadron scattering is emphasized.

Light-Front Quantization of Gauge Theories

Energy Technology Data Exchange (ETDEWEB)

Brodskey, Stanley

2002-12-01

Light-front wavefunctions provide a frame-independent representation of hadrons in terms of their physical quark and gluon degrees of freedom. The light-front Hamiltonian formalism provides new nonperturbative methods for obtaining the QCD spectrum and eigensolutions, including resolvant methods, variational techniques, and discretized light-front quantization. A new method for quantizing gauge theories in light-cone gauge using Dirac brackets to implement constraints is presented. In the case of the electroweak theory, this method of light-front quantization leads to a unitary and renormalizable theory of massive gauge particles, automatically incorporating the Lorentz and 't Hooft conditions as well as the Goldstone boson equivalence theorem. Spontaneous symmetry breaking is represented by the appearance of zero modes of the Higgs field leaving the light-front vacuum equal to the perturbative vacuum. I also discuss an ''event amplitude generator'' for automatically computing renormalized amplitudes in perturbation theory. The importance of final-state interactions for the interpretation of diffraction, shadowing, and single-spin asymmetries in inclusive reactions such as deep inelastic lepton-hadron scattering is emphasized.

Porovnanie slovenského a českého start-up ekosystému

OpenAIRE

Pipasová, Jaroslava

2017-01-01

This master thesis deals with the comparison of startup ecosystems in the Czech Republic and Slovakia. The goal is to discover which of these two countries has more developed startup ecosystem. The first chapter aims to define startup and illustrates its importance and development in both countries. The second chapter analyzes the characteristic of startup ecosystem, startup financing and supporting institutions in the 2 countries. The final chapter contains a comparison of the startup ecosys...

Preliminary experiment of non-induced plasma current startup on SUNIST spherical tokamak

International Nuclear Information System (INIS)

He Yexi; Zhang Liang; Xie Lifeng; Tang Yi; Yang Xuanzong; Fu Hongjun

2005-01-01

Non-inductive plasma current startup is an important motivation on the SUNIST spherical tokamak. In this experiment, a 100 kW, 2.45 GHz magnetron microwave system has been applied to the plasma current startup. Besides the toroidal field, a vertical field was applied to generate a preliminary toroidal plasma current without action of the central solenoid. As the evidence of the plasma current startup by the vertical field drift effect, the direction of the plasma current is changed with the changing direction of the vertical field during ECR startup discharge. We have also observed the plasma current maximum by scanning the vertical field in both directions. Additionally, we have used electrode discharge to assist the ECR current startup. (author)

Startup transient simulation for natural circulation boiling water reactors in PUMA facility

International Nuclear Information System (INIS)

Kuran, S.; Xu, Y.; Sun, X.; Cheng, L.; Yoon, H.J.; Revankar, S.T.; Ishii, M.; Wang, W.

2006-01-01

In view of the importance of instabilities that may occur at low-pressure and -flow conditions during the startup of natural circulation boiling water reactors, startup simulation experiments were performed in the Purdue University Multi-Dimensional Integral Test Assembly (PUMA) facility. The simulations used pressure scaling and followed the startup procedure of a typical natural circulation boiling water reactor. Two simulation experiments were performed for the reactor dome pressures ranging from 55 kPa to 1 MPa, where the instabilities may occur. The experimental results show the signature of condensation-induced oscillations during the single-phase-to-two-phase natural circulation transition. The results also suggest that a rational startup procedure is needed to overcome the startup instabilities in natural circulation boiling water reactor designs

Blocking-resistant communication through domain fronting

Directory of Open Access Journals (Sweden)

Fifield David

2015-06-01

Full Text Available We describe “domain fronting,” a versatile censorship circumvention technique that hides the remote endpoint of a communication. Domain fronting works at the application layer, using HTTPS, to communicate with a forbidden host while appearing to communicate with some other host, permitted by the censor. The key idea is the use of different domain names at different layers of communication. One domain appears on the “outside” of an HTTPS request—in the DNS request and TLS Server Name Indication—while another domain appears on the “inside”—in the HTTP Host header, invisible to the censor under HTTPS encryption. A censor, unable to distinguish fronted and nonfronted traffic to a domain, must choose between allowing circumvention traffic and blocking the domain entirely, which results in expensive collateral damage. Domain fronting is easy to deploy and use and does not require special cooperation by network intermediaries. We identify a number of hard-to-block web services, such as content delivery networks, that support domain-fronted connections and are useful for censorship circumvention. Domain fronting, in various forms, is now a circumvention workhorse. We describe several months of deployment experience in the Tor, Lantern, and Psiphon circumvention systems, whose domain-fronting transports now connect thousands of users daily and transfer many terabytes per month.

Quel contrôle de gestion pour les startups ?

OpenAIRE

Meyssonnier , François

2015-01-01

Une étude de huit PME fondées sur la science permet d’identifier les spécificités du contrôle de gestion des startups. Dans les startups émergentes le dirigeant n’utilise que des linéaments de contrôle de gestion essentiellement pour développer son approche cognitive du business model. Dans les startups en croissance le contrôle de gestion a un rôle de garde-fou et les outils de pilotage de la performance sont utilisés essentiellement de façon interactive et pour la prévision. Les principaux ...

Front-end Intelligence for triggering and local track recognition in Gas Pixel Detectors

CERN Document Server

Hessey, NP; The ATLAS collaboration; van der Graaf, H; Vermeulen, J; Jansweijer, P; Romaniouk, A

2012-01-01

The combination of gaseous detectors with pixel readout chips gives unprecedented hit resolution (improving from O(100 um) for wire chambers to 10 um), as well as high-rate capability, low radiation length and giving in addition angular information on the local track. These devices measure individually every electron liberated by the passage of a charged particle, leading to a large quantity of data to be read out. Typically an external trigger is used to start the read-out. We are investigating the addition of local intelligence to the pixel read-out chip. A first level of processing detects the passage of a particle through the gas volume, and accurately determines the time of passage. A second level measures in an approximate but fast way the tilt-angle of the track. This can be used to trigger a third stage in which all hits associated to the track are processed locally to give a least-squares-fit to the track. The chip can then send out just the fitted track parameters instead of the individual electron ...

Application of an automatic cloud tracking technique to Meteosat water vapor and infrared observations

Science.gov (United States)

Endlich, R. M.; Wolf, D. E.

1980-01-01

The automatic cloud tracking system was applied to METEOSAT 6.7 micrometers water vapor measurements to learn whether the system can track the motions of water vapor patterns. Data for the midlatitudes, subtropics, and tropics were selected from a sequence of METEOSAT pictures for 25 April 1978. Trackable features in the water vapor patterns were identified using a clustering technique and the features were tracked by two different methods. In flat (low contrast) water vapor fields, the automatic motion computations were not reliable, but in areas where the water vapor fields contained small scale structure (such as in the vicinity of active weather phenomena) the computations were successful. Cloud motions were computed using METEOSAT infrared observations (including tropical convective systems and midlatitude jet stream cirrus).

Assessment on Startup Ramp Rate and Threshold Power of OPR1000

Energy Technology Data Exchange (ETDEWEB)

Kim, Kiyoung; Kim, Yongbae; Cha, Gyunho; Kim, Yongdeog [Korea Hydro and Nuclear Power Co., Ltd., Daejeon (Korea, Republic of)

2014-05-15

This paper summarizes PCI assessment according to several startup ramp rates and threshold power assessment of OPR1000. The definition of threshold power is maximum value in power range that can increase startup ramp rate rapidly. FALCON code is used for PCI assessment and it is analyzed for once-burned fuel because it is the most sensitive to PCI failure. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. The PCI analyses were conducted for the once-burned fuel from the start of the second cycle to plant power 100%. This paper presents both the PCI analysis according to startup ramp rates and threshold power assessment result like below. · The more startup ramp rate is increased, the more PCI failure probability is decreased in low power range (≤ 40%). · PCI failure is not occurred even though startup ramp rate is 10%/hr until the plant power reaches 55%.

Assessment on Startup Ramp Rate and Threshold Power of OPR1000

International Nuclear Information System (INIS)

Kim, Kiyoung; Kim, Yongbae; Cha, Gyunho; Kim, Yongdeog

2014-01-01

This paper summarizes PCI assessment according to several startup ramp rates and threshold power assessment of OPR1000. The definition of threshold power is maximum value in power range that can increase startup ramp rate rapidly. FALCON code is used for PCI assessment and it is analyzed for once-burned fuel because it is the most sensitive to PCI failure. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. The PCI analyses were conducted for the once-burned fuel from the start of the second cycle to plant power 100%. This paper presents both the PCI analysis according to startup ramp rates and threshold power assessment result like below. · The more startup ramp rate is increased, the more PCI failure probability is decreased in low power range (≤ 40%). · PCI failure is not occurred even though startup ramp rate is 10%/hr until the plant power reaches 55%

Three-dimensional tracking for efficient fire fighting in complex situations

Science.gov (United States)

Akhloufi, Moulay; Rossi, Lucile

2009-05-01

Each year, hundred millions hectares of forests burn causing human and economic losses. For efficient fire fighting, the personnel in the ground need tools permitting the prediction of fire front propagation. In this work, we present a new technique for automatically tracking fire spread in three-dimensional space. The proposed approach uses a stereo system to extract a 3D shape from fire images. A new segmentation technique is proposed and permits the extraction of fire regions in complex unstructured scenes. It works in the visible spectrum and combines information extracted from YUV and RGB color spaces. Unlike other techniques, our algorithm does not require previous knowledge about the scene. The resulting fire regions are classified into different homogenous zones using clustering techniques. Contours are then extracted and a feature detection algorithm is used to detect interest points like local maxima and corners. Extracted points from stereo images are then used to compute the 3D shape of the fire front. The resulting data permits to build the fire volume. The final model is used to compute important spatial and temporal fire characteristics like: spread dynamics, local orientation, heading direction, etc. Tests conducted on the ground show the efficiency of the proposed scheme. This scheme is being integrated with a fire spread mathematical model in order to predict and anticipate the fire behaviour during fire fighting. Also of interest to fire-fighters, is the proposed automatic segmentation technique that can be used in early detection of fire in complex scenes.

Detector techniques and data acquisition for LHC experiments

CERN Document Server

AUTHOR|(CDS)2071367; Cittolin, Sergio; CERN. Geneva

1996-01-01

An overview of the technologies for LHC tracking detectors, particle identification and calorimeters will be given. In addition, the requirements of the front-end readout electronics for each type of detector will be addressed. The latest results from the R&D studies in each of the technologies will be presented. The data handling techniques needed to read out the LHC detectors and the multi-level trigger systems used to select the events of interest will be described. An overview of the LHC experiments data acquisition architectures and their current state of developments will be presented.

Alignment of the ATLAS Inner Detector Tracking System

CERN Document Server

Moles-Valls, R

2008-01-01

The ATLAS experiment is equipped with a tracking system for c harged particles built on two technologies: silicon and drift tube base detectors. These kind of detectors compose the ATLAS Inner Detector (ID). The Alignment of the ATLAS ID tracking s ystem requires the determination of almost 36000 degrees of freedom. From the tracking point o f view, the alignment parameters should be know to a few microns precision. This permits to att ain optimal measurements of the parameters of the charged particles trajectories, thus ena bling ATLAS to achieve its physics goals. The implementation of the alignment software, its framewor k and the data flow will be discussed. Special attention will be paid to the recent challenges wher e large scale computing simulation of the ATLAS detector has been performed, mimicking the ATLAS o peration, which is going to be very important for the LHC startup scenario. The alignment r esult for several challenges (real cosmic ray data taking and computing system commissioning) will be...

40 CFR 63.2852 - What is a startup, shutdown, and malfunction plan?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What is a startup, shutdown, and... Production Compliance Requirements § 63.2852 What is a startup, shutdown, and malfunction plan? You must...)(2) malfunction period, or the § 63.2850(c)(2) or (d)(2) initial startup period. The SSM plan must...

Interdisciplinarity in Tech Startups Development – Case Study of ‘Unistartapp’ Project

Directory of Open Access Journals (Sweden)

Kopera Sebastian

2018-03-01

Full Text Available Empirical data as well as scientific reports confirm that startups require diverse, in-house competencies in order to achieve market success. However, while technology-related competencies are usually brought to new tech ventures by their founders, there is a significant deficiency of market- and management-related competencies, which is reflected in the statistics of common startup failure reasons. In this context, a question arises: how interdisciplinarity of knowledge and competencies can be built into the very core of tech startups? The text addresses this question by zeroing in on the role of universities in this process. In the first part, the specificity of tech startups is analyzed. The next chapter overviews the hitherto academy-related startup education environment together with its shortcomings as far as interdisciplinarity is concerned. Finally, the case study of innovative and interdisciplinary academic ecosystem, which was built and tested within the project UniStartApp, is presented and discussed together with related lessons learned. The text is concluded with final remarks on challenges involved in embedding interdisciplinarity into startup education ecosystem.

New start-up channels and multichannel analyzer at the RB reactor; Novi start-up kanali i videkanalni analizator na reaktoru Rb

Energy Technology Data Exchange (ETDEWEB)

Sotic, O; Markovic, H; Vranic, S; Dimitrijevic, Z; Pesic, M [Boris Kidric Institute of Nuclear Sciences Vinca, Beograd (Yugoslavia)

1978-01-15

New start-up channels and a multichannel analyzer were purchased in 1977 for the RB reactor. Both start-up channels contain BF{sub 3} neutron detectors, preamplifier, amplifier, single-channel analyzer, scaler, ratemeter, control unit, recording instrument. This document contains detailed technical description of these devices as well as characteristics of the multichannel analyzer which is being tested and will be used for measuring irradiation in the vicinity of the reactor.

Determination of radon and thoron permeability through some plastics by track technique

Energy Technology Data Exchange (ETDEWEB)

Hafez, A.-F.; Somogyi, G.

1986-01-01

Experiments have been performed to study the usefulness of several types of plastic foils as filter to separate radon and thoron. Time-integrated alpha-activity measurements have been carried out by using the so-called ''can-technique'' equipped with both LR-115 and CR-39 track detectors. The track density observed on the detectors, taken as a measure of radon activity concentration, has been determined as a function of the thickness of filter foils. The radon permeability and the thoron separation factors have been determined. It is shown that various plastic foils exhibit considerable differences in radon diffusion coefficient owing to their different chemical structures. Among the plastic foils investigated the polyethylene proved to have the highest gas diffusion coefficient.

Advanced Tracking of Vehicles

DEFF Research Database (Denmark)

Jensen, Christian Søndergaard; Li, K.-J.; Pakalnis, Stardas

2005-01-01

efficient tracking techniques. More specifically, while almost all commercially available tracking solutions simply offer time-based sampling of positions, this paper's techniques aim to offer a guaranteed tracking accuracy for each vehicle at the lowest possible costs, in terms of network traffic...

40 CFR 60.2918 - What happens during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What happens during periods of startup... of startup, shutdown, and malfunction? The emission limitations and operating limits apply at all times except during OSWI unit startups, shutdowns, or malfunctions. Performance Testing ...

Electron cyclotron resonance heating assisted plasma startup in the Tore Supra tokamak

International Nuclear Information System (INIS)

Bucalossi, J.; Hertout, P.; Lennholm, M.; Saint-Laurent, F.; Bouquey, F.; Darbos, C.; Traisnel, E.

2009-04-01

ECRH assisted plasma startup at fundamental resonance is investigated in Tore Supra in view of ITER operation. ECRH pre-ionisation is found to be very efficient allowing plasma initiation in a wide range of pre-fill pressure compared to ohmic startup. Reliable assisted startup has been achieved at the ITER reference toroidal electric field (0.3 V/m) with 160 kW of ECRH. Resonance location scan indicates that the plasma is initiated at the resonance location and that the plasma current channel position had to be real-time controlled since the very beginning of the discharge to obtain robust plasma startup. (authors)

Novel start-up circuit with enhanced power-up characteristic for bandgap references

DEFF Research Database (Denmark)

Tuan Vu, Cao; Wisland, Dag T.; Lande, Tor Sverre

This paper presents a new start-up circuit for low-power bandgap reference (BGR) voltage generators. The BGR is designed for providing a stable 0.3 V power supply for application in low power wireless sensor nodes. The BGR has an enhanced power-up characteristic and demonstrates a reduction...... of the total stand-by current. Simulated results confirm that the proposed start-up circuit does not affect the performance of the BGR even though the supply voltage (VDD) is higher and has more stable power-up characteristic than the conventional start-up circuits. The new start-up circuit is designed with 65...

Anode front-end electronics for the cathode strip chambers of the CMS Endcap Muon detector

International Nuclear Information System (INIS)

Ferguson, T.; Bondar, N.; Golyash, A.; Sedov, V.; Terentiev, N.; Vorobiev, I.

2005-01-01

The front-end electronics system for the anode signals of the CMS Endcap Muon cathode strip chambers has about 183,000 channels. The purposes of the anode front-end electronics are to acquire precise muon timing information for bunch crossing number identification at the Level-1 muon trigger system and to provide a coarse radial position of the muon track. Each anode channel consists of an input protection network, amplifier, shaper, constant-fraction discriminator, and a programmable delay. The essential parts of the electronics include a 16-channel amplifier-shaper-discriminator ASIC CMP16 and a 16-channel ASIC D16G providing programmable time delay. The ASIC CMP16 was optimized for the large cathode chamber size (up to 3x2.5 m 2 ) and for the large input capacitance (up to 200 pF). The ASIC combines low power consumption (30 mW/channel) with good time resolution (2-3 ns). The delay ASIC D16G makes possible the alignment of signals with an accuracy of 2.2 ns. This paper presents the anode front-end electronics structure and results of the preproduction and the mass production tests, including radiation resistance and reliability tests. The special set of test equipment, techniques, and corresponding software developed and used in the test procedures are also described

Development of nuclear microfilters using the fission tracks registration technique

International Nuclear Information System (INIS)

Yamasaki, I.M.; Geraldo, L.P.

1990-10-01

Nuclear microfilters with mean pores diameter in the range from 1.9 to 10.6 μm have been produced using the fission tracks registration technique in Makrofol KG (8 μm thickness). Fluctuations around 11% and 10% were obtained respectively for the pores size and pores uniformity in the analysis of a typical sample of microfilter. The essential features of the microfilters were similar to those ones, commercially known as Nuclepore and thus they may be routinely employed in the several applications areas of the Industry and Biology. (author)

Factors influencing performance within startup assistance organizations

Directory of Open Access Journals (Sweden)

Ceaușu Ioana

2017-07-01

Full Text Available Startup assistance organizations, and especially business accelerators have gained a lot of traction in the last years, captioning not only the attention of the public, but most importantly that of investors and other stakeholders. It has become a challenge for many all around the world to develop such programs, but many have failed or did not have their expected results, meaning medium to long-term sustainable and profitable alumni start-ups. As high amounts of resources, both human and financial, are being invested in the design and development of such programs, it is important to understand what sets apart the successful business acceleration programs from the ones that fail. The current paper is reviewing the up-to-date theoretical literature and studies on the matter at hand, in order to identify the most relevant factors influencing startup assistance organizations’ performance. The objective behind identifying these factors is to get a better understanding of best practices of such successful programs and set the basis for future research regarding the development of a set of metrics for more accurately measuring their performance.

40 CFR 63.310 - Requirements for startups, shutdowns, and malfunctions.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Requirements for startups, shutdowns, and malfunctions. 63.310 Section 63.310 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... CATEGORIES National Emission Standards for Coke Oven Batteries § 63.310 Requirements for startups, shutdowns...

The neighbor enclosed area tracking algorithm and its application to cyclone merger in the midlatitudes

Science.gov (United States)

Inatsu, Masaru; Amada, Shotarou; Satake, Yuya

2010-05-01

The neighbor enclosed area tracking (NEAT) algorithm is proposed as an alternative method to conventional point-to-point cyclone tracking approaches. Most automated Lagrangian tracking algorithms contain three procedures: cyclone identification, cyclone tracking, and quantification of cyclone intensity and activity. The cyclone identification was simply based on a comparison of neighboring grid points; cyclone tracking mainly employed a near-neighbor point search to neighbor-time cyclone-center datasets; and cyclone intensity and activity are mainly quantified as cyclone track density, and other accompanying products such as genesis and lysis densities, mean lifetime, average moving vector, and mean growth rate can also be obtained in the final procedure. But a crucial problem in the above technique is its requirement of some complicated connecting conditions for near-neighbor tracking. To overcome the problem, NEAT completes cyclone identification and cyclone tracking in a single process of equivalent labeling for spatiotemporally connected domains, i.e., if two spatially enclosed areas in a neighboring time frame overlap, they should be connected. NEAT enables us to count the genesis and tracks of individual cyclones as the conventional tracking. Moreover, NEAT has the ability to produce fruitful information on cyclone mergers and separations, cyclone shape, and material transport by individual eddies (the latter two features will be reported elsewhere). There are many possible applications of NEAT to meteorology and oceanography, but now we focus on the situation, well-known by Japanese synopticians, that two cyclones pass respectively over the north and south of Japan and then they frequently merge and are rapidly deepened in the western Pacific. For the case, the southern cyclones tend to be stimulated just above the sea surface temperature front to the north of oceanic western boundary currents, while the northern cyclones, moving eastward along the polar

The Core Interaction of Platforms: How Startups Connect Users and Producers

Directory of Open Access Journals (Sweden)

Heidi M. E. Korhonen

2017-09-01

Full Text Available The platform economy is disrupting innovation while presenting both opportunities and challenges for startups. Platforms support value creation between multiple participant groups, and this operationalization of an ecosystem’s value co-creation represents the “core interaction” of a platform. This article focuses on that core interaction and studies how startups connect producers and users in value-creating core interaction through digital platforms. The study is based on an analysis of 29 cases of platform startups interviewed at a leading European startup event. The studied startups were envisioning even millions of users and hundreds or thousands of producers co-creating value on their platforms. In such platform businesses, our results highlight the importance of attracting a large user pool, providing novel services to those users, offering a new market for producers, supporting the core interaction in various ways, and utilizing elements of the platform canvas – an adaptation of the business model canvas, which we have accommodated for platform-based business models – to accomplish these goals.

Statement on the first research on digital startups in Poland

Directory of Open Access Journals (Sweden)

Agnieszka Skala

2016-10-01

Full Text Available The objective of the paper is to present the results of the first study of Polish startups’ ecosystem as the first stage of a larger study of digital economy landscape in Poland. The first estimate of the number of Polish startups amounts to 2400 entities. The publication presents the first survey Polish startups that marks the beginning of cyclical studies on enterprises belonging to the digital economy in Poland. The study was conducted among 423 entities using an in-house questionnaire prepared based on the author’s own knowledge. Results are discussed. Startups most often consider themselves software producers who follow the SaaS model and operate in the following industries: mobile apps, e-commerce and Internet services. Nearly one in three startups achieve 50% annual revenue growth, while in one-fifth such growth exceeds 100%. Almost two thirds of Polish startups are financed exclusively from own funds. It is necessary to repeat and deepen the study in order to determining the significance of the digital industry in the economy of Poland and the CEE region. The originality of this work lies in taking this subject for the first time in Polish literature and in elaborating the proposition of a “startup” term’s definition.

Successful transjugular extraction of a lead in front of the anterior scalene muscle by using snare technique

Directory of Open Access Journals (Sweden)

Ayako Okada, MD

2015-08-01

Full Text Available The incidence of cardiovascular implantable electronic device infection is increasing. We report a case of and successful device removal in a 79-year-old man with implantable cardioverter-defibrillator infection. Right phrenic nerve paralysis was evident on chest radiography. The lead was in front of the anterior scalene muscle, close to the left phrenic nerve. Therefore, extraction carried a risk of bilateral phrenic nerve paralysis. The lead was successfully extracted from the right internal jugular vein by using the snare technique. No complications occurred, and the extraction was successful.

40 CFR 60.2685 - What happens during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What happens during periods of startup... happens during periods of startup, shutdown, and malfunction? (a) The emission limitations and operating limits apply at all times except during CISWI unit startups, shutdowns, or malfunctions. (b) Each...

40 CFR 60.3025 - What happens during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What happens during periods of startup... during periods of startup, shutdown, and malfunction? The emission limitations and operating limits apply at all times except during OSWI unit startups, shutdowns, or malfunctions. Model Rule—Performance...

AGATA gamma-ray tracking simulations and data analysis working group

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The purpose of this meeting was to review the present state of the AGATA project (Advanced GAmma Tracking Array). The following issues were dealt with: -) detectors and preamplifiers, -) ancillary detectors, -) tracking, -) physics simulations and key experiments, -) in-beam tests, -) data acquisition, -) data processing: front end electronics, and -) infrastructure. This document gathers only the slides of the presentations.

AGATA gamma-ray tracking simulations and data analysis working group

International Nuclear Information System (INIS)

2007-01-01

The purpose of this meeting was to review the present state of the AGATA project (Advanced GAmma Tracking Array). The following issues were dealt with: -) detectors and preamplifiers, -) ancillary detectors, -) tracking, -) physics simulations and key experiments, -) in-beam tests, -) data acquisition, -) data processing: front end electronics, and -) infrastructure. This document gathers only the slides of the presentations

Digital Innovations: Startup Marketing Strategy for Global Growth

OpenAIRE

Gröhn, Hanna

2017-01-01

This thesis discusses the relatively new phenomena of innovative digital products created by startup companies, who often must scale globally fast, before the volatile trends or the fierce competition of the digital marketspace take over. International entry itself is no longer the issue, but rather standing out in the crowd while balancing resources and flexibility. The focus is on how startups can induce global growth and tackle structural obstacles by means of marketing strategy. The t...

Estimation of trace levels of plutonium in urine samples by fission track technique

International Nuclear Information System (INIS)

Sawant, P.D.; Prabhu, S.; Pendharkar, K.A.; Kalsi, P.C.

2009-01-01

Individual monitoring of radiation workers handling Pu in various nuclear installations requires the detection of trace levels of plutonium in bioassay samples. It is necessary to develop methods that can detect urinary excretion of Pu in fraction of mBq range. Therefore, a sensitive method such as fission track analysis has been developed for the measurement of trace levels of Pu in bioassay samples. In this technique, chemically separated plutonium from the sample and a Pu standard were electrodeposited on planchettes and covered with Lexan solid state nuclear track detector (SSNTD) and irradiated with thermal neutrons in APSARA reactor of Bhabha Atomic Research Centre, India. The fission track densities in the Lexan films of the sample and the standard were used to calculate the amount of Pu in the sample. The minimum amount of Pu that can be analyzed by this method using doubly distilled electronic grade (E. G.) reagents is about 12 μBq/L. (author)

40 CFR 60.2953 - What information must I submit prior to initial startup?

Science.gov (United States)

2010-07-01

... initial startup? 60.2953 Section 60.2953 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... initial startup? You must submit the information specified in paragraphs (a) through (e) of this section prior to initial startup. (a) The type(s) of waste to be burned. (b) The maximum design waste burning...

40 CFR 60.2195 - What information must I submit prior to initial startup?

Science.gov (United States)

2010-07-01

... initial startup? 60.2195 Section 60.2195 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY..., 2001 Recordkeeping and Reporting § 60.2195 What information must I submit prior to initial startup? You... startup. (a) The type(s) of waste to be burned. (b) The maximum design waste burning capacity. (c) The...

Directional Track Selection Technique in CR39 SSNTD for lowyield reaction experiments

Science.gov (United States)

Ingenito, Francesco; Andreoli, Pierluigi; Batani, Dimitri; Bonasera, Aldo; Boutoux, Guillaume; Burgy, Frederic; Cipriani, Mattia; Consoli, Fabrizio; Cristofari, Giuseppe; De Angelis, Riccardo; Di Giorgio, Giorgio; Ducret, Jean Eric; Giulietti, Danilo; Jakubowska, Katarzyna

2018-01-01

There is a great interest in the study of p-11B aneutronic nuclear fusion reactions, both for energy production and for determination of fusion cross-sections at low energies. In this context we performed experiments at CELIA in which energetic protons, accelerated by the laser ECLIPSE, were directed toward a solid Boron target. Because of the small cross-sections at these energies the number of expected reactions is low. CR39 Solid-State Nuclear Track Detectors (SSNTD) were used to detect the alpha particles produced. Because of the low expected yield, it is difficult to discriminate the tracks due to true fusion products from those due to natural background in the CR39. To this purpose we developed a methodology of particle recognition according to their direction with respect to the detector normal, able to determine the position of their source. We applied this to the specific experiment geometry, so to select from all the tracks those due to particles coming from the region of interaction between accelerated protons and solid boron target. This technique can be of great help on the analysis of SSNTD in experiments with low yield reactions, but can be also generally applied to any experiment where particles reach the track detector with known directions, and for example to improve the detection limit of particle spectrometers using CR39.

Optimal relations of the parameters ensuring safety during reactor start-up

International Nuclear Information System (INIS)

Yurkevich, G.P.

2004-01-01

Procedure and equations for the determination of optimal ratio between parameters allowing safe removal of reactor in critical state are suggested. Initial pulse frequency of pulsed start-up channel and power of neutron source are decreased by reduced rate of changing reactivity during automatic start-up, disposition of pulsed neutron detector in the range with neutron flux density to 5·10 12 s -1 cm -2 at standard power, separate signal of period for the use in chains of automatic start-up and emergency protection, reduction of pulses frequency of the start-up channel (the frequency is equal to 4000 c -1 ). Procedure and equations for the determination of optimal parameters are effected with the account of statistic character of pulsed detector frequency and false outlet signal [ru

40 CFR 62.14645 - What happens during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false What happens during periods of startup... Limits § 62.14645 What happens during periods of startup, shutdown, and malfunction? (a) The emission limitations and operating limits apply at all times except during periods of CISWI unit startup, shutdown, or...

40 CFR 60.2120 - What happens during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What happens during periods of startup... 1, 2001 Emission Limitations and Operating Limits § 60.2120 What happens during periods of startup... during CISWI unit startups, shutdowns, or malfunctions. (b) Each malfunction must last no longer than 3...

The Emergence of the Lean Global Startup as a New Type of Firm

Directory of Open Access Journals (Sweden)

Erik Stavnsager Rasmussen

2015-11-01

Full Text Available This article contributes to the interplay between international entrepreneurship, innovation networks, and early internationalization research by emphasizing the need to conceptualize and introduce a new type of firm: the lean global startup. It discussed two different paths in linking the lean startup and born-global internationalization strategies. The first path refers to generic lean startups that have undertaken a rapid internationalization strategy (i.e., lean-to-global startups. The second path refers to startups that have started operating on global scale since their inception and adopted the lean startup approach by seamlessly synergizing their global and lean product development activities. The article emphasizes several aspects that could be used as part of the theoretical foundation for conceptualizing lean global startups as a special new type of firm: i the emergent nature of their business models, including the challenges of partnership development on a global scale; ii the inherently relational nature of the global resource allocation processes; iii the integration of the entrepreneurial, effectuation, and global marketing perspectives; iv the need to deal with a high degree of uncertainty, including the uncertainty associated with cross-border business operations; and v linking the ex-ante characteristics of lean startups with the ex-post characteristics of born-global firms in order to develop a technology adoption marketing perspective that considers the “crossing the chasm” process as a successful entry into a global market niche.

On the Importance of "Front-Side Mechanics" in Athletics Sprinting.

Science.gov (United States)

Haugen, Thomas; Danielsen, Jørgen; Alnes, Leif Olav; McGhie, David; Sandbakk, Øyvind; Ettema, Gertjan

2018-05-16

Practitioners have, for many years, argued that athletic sprinters should optimize front-side mechanics (leg motions occurring in front of the extended line through the torso) and minimize back-side mechanics. This study aimed to investigate if variables related to front- and back-side mechanics can be distinguished from other previously highlighted kinematic variables (spatiotemporal variables and variables related to segment configuration and velocities at touchdown) in how they statistically predict performance. A total of 24 competitive sprinters (age: 23.1 [3.4] y, height: 1.81 [0.06] m, body mass: 75.7 [5.6] kg, and 100-m personal best: 10.86 [0.22] s) performed two 20-m starts from block and 2 to 3 flying sprints over 20 m. Kinematics were recorded in 3D using a motion tracking system with 21 cameras at a 250 Hz sampling rate. Several front- and back-side variables, including thigh (r = .64) and knee angle (r = .51) at lift-off and maximal thigh extension (r = .66), were largely correlated (P mechanics were crucial for sprint performance among the investigated sprinters.

Acetate enhances startup of a H₂-producing microbial biocathode.

Science.gov (United States)

Jeremiasse, Adriaan W; Hamelers, Hubertus V M; Croese, Elsemiek; Buisman, Cees J N

2012-03-01

H(2) can be produced from organic matter with a microbial electrolysis cell (MEC). To decrease MEC capital costs, a cathode is needed that is made of low-cost material and produces H(2) at high rate. A microbial biocathode is a low-cost candidate, but suffers from a long startup and a low H(2) production rate. In this study, the effects of cathode potential and carbon source on microbial biocathode startup were investigated. Application of a more negative cathode potential did not decrease the startup time of the biocathode. If acetate instead of bicarbonate was used as carbon source, the biocathode started up more than two times faster. The faster startup was likely caused by a higher biomass yield for acetate than for bicarbonate, which was supported by thermodynamic calculations. To increase the H(2) production rate, a flow through biocathode fed with acetate was investigated. This biocathode produced 2.2 m(3) H(2) m(-3)  reactor day(-1) at a cathode potential of -0.7 V versus NHE, which was seven times that of a parallel flow biocathode of a previous study. Copyright © 2011 Wiley Periodicals, Inc.

Social network analysis for startups finding connections on the social web

CERN Document Server

Tsvetovat, Maksim

2011-01-01

Does your startup rely on social network analysis? This concise guide provides a statistical framework to help you identify social processes hidden among the tons of data now available. Social network analysis (SNA) is a discipline that predates Facebook and Twitter by 30 years. Through expert SNA researchers, you''ll learn concepts and techniques for recognizing patterns in social media, political groups, companies, cultural trends, and interpersonal networks. You''ll also learn how to use Python and other open source tools-such as NetworkX, NumPy, and Matplotlib-to gather, analyze, and vis

Track Detection Technique Using CR-39 for Determining Depleted Uranium in Biological Specimens

International Nuclear Information System (INIS)

Murbat, S.M.

2013-01-01

Track detecting technique using CR-39 track detector has been implemented for determining depleted uranium concentration in biological specimens (tissues, bones, and blood) of patients infected with cancer diseases. Results were compared with specimens of patients infected with conventional diseases (noncancerous). Specimens were collected from middle and south of Iraq have been contaminated with depleted uranium in the Gulf war in 1991. Results show that this technique is efficient for determining depleted uranium concentration in biological specimens. It was found that all studies samples determine for patients infected with cancer diseases contain a high concentration of depleted uranium (more than the international standard) comparing with noncancerous diseases. Moreover, it was found that persons infected with Leukemia show more sensitive to uranium concentrations to induce the diseases (66-202 ppb), while (116- 1910 ppb) concentrations were needed for inducing cancer diseases in organs and tissues. Result confirmed the correlation between cancerous diseases and the munitions made of depleted uranium used in the Gulf war in 1991 leads to contaminate the Iraqi environment and causes a high risk against people in Iraq.

Start-up procedure

International Nuclear Information System (INIS)

Marchl, A.; Krebs, W.D.; Aleite, W.

1975-01-01

The start-up procedure will be shown on a pressurized water reactor, although most of the activities will occur similarly in other reactor types. The commissioning time can be divided into 5 sections, the phases A to E together lasting 26 months. Subsequently there are a test run of one month and the handling-over of the plant to the operator. A survey of the commissioning sections with several important main events is shown. (orig./TK) [de

How Types of Organisational Culture Shapes Successful Start-ups within Malaysia

OpenAIRE

Kuah, Shen Yang

2016-01-01

Start-ups is the new wave of firms which are now mushrooming around Malaysia. However, as this wave is still at its infancy the success rate of start-ups in Malaysia is extremely low. It has been long established that organisational culture does indeed effect the performance of a firm, however there haven’t been any reports on the effect of organisational culture on the success of start-ups. The objective of this report is to investigate how different types of organisational cultures contribu...

Software for physical start-up console

International Nuclear Information System (INIS)

Arbet, L.; Suchy, R.

1991-01-01

The physical start-up console comprises an PC AT-based control unit equipped with an 80386 processor, and information input/output units. The basic functions to be fulfilled by the control unit software include data acquisition related to the following parameters: neutron physics properties of the reactor core (neutron fluxes recorded by ionization chambers and reactivity recorded by a digital reactimeter), positions of the reactor core control elements (by the digital position meter) and reactor core control measurements, and technological quantities requisite for evaluating physical start-up tests. The measured and calculated data are shown on the control unit display. The setup of the data acquisition system and of user programs is dealt with, and characteristics of the user processes are briefly described. (Z.S.)

Dual Use of Image Based Tracking Techniques: Laser Eye Surgery and Low Vision Prosthesis

Science.gov (United States)

Juday, Richard D.; Barton, R. Shane

1994-01-01

With a concentration on Fourier optics pattern recognition, we have developed several methods of tracking objects in dynamic imagery to automate certain space applications such as orbital rendezvous and spacecraft capture, or planetary landing. We are developing two of these techniques for Earth applications in real-time medical image processing. The first is warping of a video image, developed to evoke shift invariance to scale and rotation in correlation pattern recognition. The technology is being applied to compensation for certain field defects in low vision humans. The second is using the optical joint Fourier transform to track the translation of unmodeled scenes. Developed as an image fixation tool to assist in calculating shape from motion, it is being applied to tracking motions of the eyeball quickly enough to keep a laser photocoagulation spot fixed on the retina, thus avoiding collateral damage.

26 CFR 1.195-1T - Election to amortize start-up expenditures (temporary).

Science.gov (United States)

2010-04-01

... business, or $5,000 (reduced (but not below zero) by the amount by which the start-up expenditures exceed... beginning with the month in which the active trade or business begins. All start-up expenditures that relate to the active trade or business are considered in determining whether the start-up expenditures...

Organising a conference? Think about what you can do for start-ups!

CERN Multimedia

David Mazur

2016-01-01

ICTR-PHE 2016 welcomed 16 exhibitors and sponsors as part of its industrial exhibition. If you have ever (co-)organised a large scientific conference, you almost certainly have your own list of major industrial actors who could be interested in becoming exhibitors or sponsors.   The six start-ups present at ICTR-PHE 2016 – Oncoradiomics, Colnec Health, Dixit Solutions, e-Learning4Health, I-See Computing and SmART Scientific Solutions (not pictured). (Image: Salvatore Fiore) ICTR-PHE has shown that scientific conferences can have a catalysing role in transforming young start-ups and spin-off companies into the key industrial players of tomorrow. A special start-up corner was provided in the industrial exhibition, where small stands were made available for a modest fee to start-ups and spin-off companies in fields relevant to the conference theme, together with a 5-minute timeslot for a pitch to the audience. Six start-ups, from the Netherlands, Italy and France...

Model based analysis of the time scales associated to pump start-ups

Energy Technology Data Exchange (ETDEWEB)

Dazin, Antoine, E-mail: antoine.dazin@lille.ensam.fr [Arts et métiers ParisTech/LML Laboratory UMR CNRS 8107, 8 bld Louis XIV, 59046 Lille cedex (France); Caignaert, Guy [Arts et métiers ParisTech/LML Laboratory UMR CNRS 8107, 8 bld Louis XIV, 59046 Lille cedex (France); Dauphin-Tanguy, Geneviève, E-mail: genevieve.dauphin-tanguy@ec-lille.fr [Univ Lille Nord de France, Ecole Centrale de Lille/CRISTAL UMR CNRS 9189, BP 48, 59651, Villeneuve d’Ascq cedex F 59000 (France)

2015-11-15

Highlights: • A dynamic model of a hydraulic system has been built. • Three periods in a pump start-up have been identified. • The time scales of each period have been estimated. • The parameters affecting the rapidity of a pump start-up have been explored. - Abstract: The paper refers to a non dimensional analysis of the behaviour of a hydraulic system during pump fast start-ups. The system is composed of a radial flow pump and its suction and delivery pipes. It is modelled using the bond graph methodology. The prediction of the model is validated by comparison to experimental results. An analysis of the time evolution of the terms acting on the total pump pressure is proposed. It allows for a decomposition of the start-up into three consecutive periods. The time scales associated with these periods are estimated. The effects of parameters (angular acceleration, final rotation speed, pipe length and resistance) affecting the start-up rapidity are then explored.

Procurement principles and vendor management in technological start-up companies

OpenAIRE

Jakobsson, Charlotta

2016-01-01

Denna studie är kopplad till direkta inköp inom teknologiska startup företag. Målet med studien är att undersöka vilka direktupphandlingsmetoder teknologiska startup företag använder sig avsamt att få reda på hur de sköter sina leverantörförhållanden. Ett vidare mål är att och på basis av resultaten ta fram inköpsrekommendationer för företagen och för Salusfin. Forskningen är begränsad till teknologiska startup företag samt deras direktupphandlings aktiviteter, och kan inte med säkerhet gener...

TFTR Mirnov coil analysis at plasma start-up

International Nuclear Information System (INIS)

Harley, T.R.; Buchenauer, D.A.; Coonrod, J.; McGuire, K.M.

1986-01-01

The methods for finding poloidal and toroidal numbers of MHD oscillations from Mirnov coils are reviewed and modified. Examples of various MHD phenomena occurring during start-up on TFTR are illustrated. It is found that the MHD mode structure best fits a model with the toroidal correction included. A new algorithm which finds m,n numbers can accommodate toroidal effects which are manifested in the phase data. The algorithm can find m,n numbers with a given toroidal correction parameter lambda', (lambda' = 0 → cylindrical). This algorithm is also used to find the optimal value of lambda' automatically, eliminating the need for ''guesswork.'' The algorithm finds the best parameters to the fit much faster than more conventional computational techniques. 9 refs., 21 figs., 2 tabs

Start-up processes’ efficiency of turbine jet engines

Directory of Open Access Journals (Sweden)

Jankowski Antoni

2016-12-01

Full Text Available The paper presents diagnoses of example start-up processes of drive units built in military aircraft operated in the Dęblin's “School of Eaglets” during the flight. The significance of this process is very important, especially from the point of view of flight safety, especially as it concerns the training aircraft, on which officer cadets-candidates for pilots are trained. The diagnosis of the start-up process was conducted using data from on-board flight recorders recorded during a flight training, whose aim was an emergency launch of particular drive units, and with the help of the so-called phase mapping of the selected operating parameters of the particular flight drive systems. The standard diagram of typical start-up systems was shown, while presenting their base subassemblies. At the end, the obtained results and the main problems that need intervention were commented, as well as further preventive activities were proposed.

Preliminary considerations on the startup phase for the ASTRID core

International Nuclear Information System (INIS)

Mignot, G.

2015-01-01

This paper presents preliminary considerations on the startup phase for the ASTRID core, as well as an overview of the different steps before reaching the optimised equilibrium core. The start-up phase is assumed to cover the period between loading the dummy core into the reactor (for commissioning tests) and achieving the optimised equilibrium core. Four main stages are considered: a first stage of start-up tests before fuel core loading, a second stage related to zero power and power ramp-up tests, a third stage corresponding to the transition from the first core to the equilibrium contractual core, and the last stage to reach the optimised performance for the equilibrium core. In the two last stages, a sub-assembly surveillance plan based on post-irradiation examinations is taken into account. As this work is in its preliminary stages, the first scenarios shown for the start-up phase must not be considered as the ASTRID reference scenarios. The scenarios strongly depend on the assumptions considered in the analysis, whereas those discussed in this paper aim at outlining the content and the duration of the starting phases for the ASTRID core, which will be useful in subsequently assessing the core sub-assembly fabrication needs. Assumptions for the start-up phase will be updated in accordance with progress on the ASTRID core design development and core qualification programme. (author)

Combination of various data analysis techniques for efficient track reconstruction in very high multiplicity events

Science.gov (United States)

Siklér, Ferenc

2017-08-01

A novel combination of established data analysis techniques for reconstructing charged-particles in high energy collisions is proposed. It uses all information available in a collision event while keeping competing choices open as long as possible. Suitable track candidates are selected by transforming measured hits to a binned, three- or four-dimensional, track parameter space. It is accomplished by the use of templates taking advantage of the translational and rotational symmetries of the detectors. Track candidates and their corresponding hits, the nodes, form a usually highly connected network, a bipartite graph, where we allow for multiple hit to track assignments, edges. In order to get a manageable problem, the graph is cut into very many minigraphs by removing a few of its vulnerable components, edges and nodes. Finally the hits are distributed among the track candidates by exploring a deterministic decision tree. A depth-limited search is performed maximizing the number of hits on tracks, and minimizing the sum of track-fit χ2. Simplified but realistic models of LHC silicon trackers including the relevant physics processes are used to test and study the performance (efficiency, purity, timing) of the proposed method in the case of single or many simultaneous proton-proton collisions (high pileup), and for single heavy-ion collisions at the highest available energies.

Overview of Maximum Power Point Tracking Techniques for Photovoltaic Energy Production Systems

DEFF Research Database (Denmark)

Koutroulis, Eftichios; Blaabjerg, Frede

2017-01-01

production of PV sources, despite the stochastically varying solar irradiation and ambient temperature conditions. Thereby, the overall efficiency of the PV energy production system is increased. Numerous techniques have been presented during the last decades for implementing the MPPT process in a PV system......A substantial growth of the installed photovoltaic (PV) systems capacity has occurred around the world during the last decade, thus enhancing the availability of electric energy in an environmentally friendly way. The maximum power point tracking (MPPT) technique enables to maximize the energy....... This chapter provides an overview of the operating principles of these techniques, which are suited for either uniform or nonuniform solar irradiation conditions. The operational characteristics and implementation requirements of these MPPT methods are also analyzed in order to demonstrate their performance...

Established Companies meet Start-ups : Case: A service to research developing business models in start-up hot spots around the globe

OpenAIRE

Eisenblätter, Simon

2016-01-01

This thesis presents a business model with the aim to improve conversation between traditional companies and newly established start-ups. The assumption that such conversation can be facilitated by scouting for innovation in start-up hot spots around the world, will be discussed throughout the paper. The purpose of this work is to lay out a plan which can be presented to a first range of possible customers, with the goal of negotiating a trial cooperation. Before introducing the busi...

Start-up of Rapsodie

International Nuclear Information System (INIS)

Pontier, R.

1967-01-01

After giving a general description of Rapsodie this report presents the conditions in which the start-up occurred and in which the tests were carried out. A chronological account is given of the operations and of the main events which occurred. The modifications made to the reactor during this period are described and a synthesis of the results obtained is presented. (author) [fr

Modeling the Financial Distress of Microenterprise StartUps Using Support Vector Machines: A Case Study

Directory of Open Access Journals (Sweden)

Antonio Blanco-Oliver

2014-10-01

Full Text Available Despite the leading role that micro-entrepreneurship plays in economic development, and the high failure rate of microenterprise start-ups in their early years, very few studies have designed financial distress models to detect the financial problems of micro-entrepreneurs. Moreover, due to a lack of research, nothing is known about whether non-financial information and nonparametric statistical techniques improve the predictive capacity of these models. Therefore, this paper provides an innovative financial distress model specifically designed for microenterprise startups via support vector machines (SVMs that employs financial, non-financial, and macroeconomic variables. Based on a sample of almost 5,500 micro- entrepreneurs from a Peruvian Microfinance Institution (MFI, our findings show that the introduction of non-financial information related to the zone in which the entrepreneurs live and situate their business, the duration of the MFI-entrepreneur relationship, the number of loans granted by the MFI in the last year, the loan destination, and the opinion of experts on the probability that microenterprise start-ups may experience financial problems, significantly increases the accuracy performance of our financial distress model. Furthermore, the results reveal that the models that use SVMs outperform those which employ traditional logistic regression (LR analysis.

Evaluation techniques of accuracy characteristics for non-contact photonic track inspection system

Science.gov (United States)

Popov, Dmitry V.; Ryabichenko, Roman B.; Krivosheina, Elena A.

2005-06-01

The most important task in Moscow metro is increasing safety of railway traffic. For safety purposes six track parameters are measured in Moscow Metro with help of track measurement car. Equipment mounted on this car works only in contact mode and doesn't provide modem requirements for accuracy. Also important task is measurement at high speeds, but contact technology limits speed of movement up to 25mph on rail switches. Current system can't measure in real-time mode. For decision of these field of tasks non-contact photonic measurement system (KSIR) is constructed. The KSIR works at speeds up to 70 mph and measure seven track parameters. The KSIR contains four subsystems: rail wear, height and track gauge measurement (BFSM); rail slump measurement (FTP); contact rail measurement (FKR); speed, level and car locating (USI). KSIR contains five CCD matrix cameras, four line CCD cameras, five infrared stripe lasers and four spot infrared lasers. Laser forms shape on the rail. CCD-camera acquires rail image and transfers it into the digital signal processor which produces preliminary calculation ofrail shape. Then image is transferred into the central computer to calculate values of rail characteristics. Angles between photonic unit and rail bring distortions in images from cameras. Additional distortions are caused by short-focus optics and small distance between camera and track. This distance is limited by structure clearance. The transformation algorithms for distortions elimination are applied. It's based on surfaces spline-approximation. As a result the KSIR calculates coefficients of approximating polynomials. The calibration is performed for checking accuracy of measurement in BFSM, FTP and FKR units. Evaluation techniques of accuracy characteristics are considered.

Light-Front Holography and the Light-Front Schrodinger Equation

Energy Technology Data Exchange (ETDEWEB)

Brodsky, Stanley J.; de Teramond, Guy

2012-08-15

One of the most important nonperturbative methods for solving QCD is quantization at fixed light-front time {tau} = t+z=c - Dirac's 'Front Form'. The eigenvalues of the light-front QCD Hamiltonian predict the hadron spectrum and the eigensolutions provide the light-front wavefunctions which describe hadron structure. More generally, we show that the valence Fock-state wavefunctions of the light-front QCD Hamiltonian satisfy a single-variable relativistic equation of motion, analogous to the nonrelativistic radial Schrodinger equation, with an effective confining potential U which systematically incorporates the effects of higher quark and gluon Fock states. We outline a method for computing the required potential from first principles in QCD. The holographic mapping of gravity in AdS space to QCD, quantized at fixed light-front time, yields the same light front Schrodinger equation; in fact, the soft-wall AdS/QCD approach provides a model for the light-front potential which is color-confining and reproduces well the light-hadron spectrum. One also derives via light-front holography a precise relation between the bound-state amplitudes in the fifth dimension of AdS space and the boost-invariant light-front wavefunctions describing the internal structure of hadrons in physical space-time. The elastic and transition form factors of the pion and the nucleons are found to be well described in this framework. The light-front AdS/QCD holographic approach thus gives a frame-independent first approximation of the color-confining dynamics, spectroscopy, and excitation spectra of relativistic light-quark bound states in QCD.

Comparing the Entrepreneurial Ecosystems for Technology Startups in Bangalore and Hyderabad, India

Directory of Open Access Journals (Sweden)

M H Bala Subrahmanya

2017-07-01

Full Text Available Technology startups are gaining increasing attention from policy makers the world over because they are seen as a means of encouraging innovations, spurring the development of new products and services, and generating employment. Technology startups tend to thrive when inserted in a conducive entrepreneurial ecosystem. Therefore, ecosystem promotion is being given increasing policy support. However, the emergence and structure of entrepreneurial ecosystems for technology startups have hardly been traced and examined in detail. In India, Bangalore occupies a unique position in the startup world, and Hyderabad is fast emerging as one of the promising startup hubs in the country. Given this background, we set out to explore and examine the structure, evolution, and growth of ecosystems for technology startups in the context of Bangalore and Hyderabad. Both the ecosystems emerged due to the initial foundation laid in the form of government–industry–academia triple helix and their interactions leading to the emergence of a modern industrial cluster followed by an information technology and biotechnology cluster, which then led to R&D cluster serving both the cities. These three clusters together, gradually and steadily, facilitated an entrepreneurial ecosystem for technology startups to emerge. The ecosystem operates within the triple helix model and has a nucleus with two outer layers: i an inner layer of primary (indispensable factors and ii an outer layer of supplementary (secondary factors. Through the analysis of the experiences of Bangalore and Hyderabad and their ecosystem evolution, its structure, and components, we derive key lessons for others within and beyond India.

Application of fission track technique for estimation of uranium concentration in drinking waters of Punjab

International Nuclear Information System (INIS)

Prabhu, S.P.; Sawant, P.D.; Raj, S.S.; Kumar, A.; Sarkar, P.K.; Tripathi, R.M.

2012-01-01

Drinking water samples were collected from four different districts, namely Bhatinda, Mansa, Faridkot and Firozpur, of Punjab for ascertaining the U(nat.) concentrations. All samples were preserved, processed and analyzed by laser fluorimetry (LF). To ensure accuracy of the data obtained by LF, few samples (10 nos) from each district were analyzed by alpha spectrometry as well as by fission track analysis (FTA) technique. For FTA technique few μl of water sample was transferred to polythene tube, lexan detector was immersed in it and the other end of the tube was also heat-sealed. Two samples and one uranium standard were irradiated in DHRUVA reactor. Irradiated detectors were chemically etched and tracks counted using an optical microscope. Uranium concentrations in samples ranged from 3.2 to 60.5 ppb and were comparable with those observed by LF. (author)

Activity Based Startup Plan for Prototype Vertical Denitration Calciner

International Nuclear Information System (INIS)

SUTTER, C.S.

1999-01-01

Testing activation on the Prototype Vertical Denitration Calciner at PFP were suspended in January 1997 due to the hold on fissile material handling in the facility. The restart of testing activities will require a review through an activity based startup process based upon Integrated Safety Management (ISM) principles to verify readiness. The Activity Based Startup Plan for the Prototype vertical Denitration Calciner has been developed for this process

Robust intelligent backstepping tracking control for uncertain non-linear chaotic systems using H∞ control technique

International Nuclear Information System (INIS)

Peng, Y.-F.

2009-01-01

The cerebellar model articulation controller (CMAC) is a non-linear adaptive system with built-in simple computation, good generalization capability and fast learning property. In this paper, a robust intelligent backstepping tracking control (RIBTC) system combined with adaptive CMAC and H ∞ control technique is proposed for a class of chaotic systems with unknown system dynamics and external disturbance. In the proposed control system, an adaptive backstepping cerebellar model articulation controller (ABCMAC) is used to mimic an ideal backstepping control (IBC), and a robust H ∞ controller is designed to attenuate the effect of the residual approximation errors and external disturbances with desired attenuation level. Moreover, the all adaptation laws of the RIBTC system are derived based on the Lyapunov stability analysis, the Taylor linearization technique and H ∞ control theory, so that the stability of the closed-loop system and H ∞ tracking performance can be guaranteed. Finally, three application examples, including a Duffing-Holmes chaotic system, a Genesio chaotic system and a Sprott circuit system, are used to demonstrate the effectiveness and performance of proposed robust control technique.

Study of the temperature effect on the surface of stainless steel using fission track technique

Energy Technology Data Exchange (ETDEWEB)

Dhawan, M M; Nagpaul, K K [Kurukshetra Univ. (India). Dept. of Physics

1977-01-01

Solid state track technique has been used to determine trace amounts of uranium in steel. Steel samples of the size 1 cm x 1 cm x 0.6 cm were ground, polished, heated to various temperatures ranging from room temperature to 900 deg C and then packed alternately with lexan detectors in an aluminium capsule for thermal neutron irradiation. After irradiation, lexan discs were removed and etched. Their surfaces were scanned under an optical microscope for measurement of track density. Uranium contents of the samples was found to vary from 6 ppm to 9 ppm.

Determination in soils of soluble uranium fraction in acid medium by fission tracks registration techniques

International Nuclear Information System (INIS)

Fernandes, G.P.

1980-01-01

The fission tracks registration technique was used to determine the concentration of uranium in soil solutions. The Makrofol KG, a synthetic plastic manufactured by Bayer, was used as a detector and the wet method was applied. The method was applied to a few samples of soils from Pocos de Caldas, Minas Gerais in Brazil. The concentrations of uranium in the samples and residues were also determined by other methods to compare the results obtained; only one sample showed deviation among the results obtained by the fission tracks method. (author)

Role of TDRSS in tracking and data acquisition

Science.gov (United States)

Spearing, R. E.

1980-01-01

The integration and operation of the Tracking Data Relay Satellite System (TDRSS) into the NASA Communications Network (NASCOM) equipment and services is described. The system concept employs spacecraft in geosynchronous orbit, operating as communications front-ends, and a single ground terminal, which provides primary tracking and data acquisition services for earth-orbiting user satellites and for the Space Shuttle. The TDRSS system is further characterized by real-time throughput of user data and a high degree of automation.

Start-up test of Fukushima Daini Nuclear Power Station Unit No.3

International Nuclear Information System (INIS)

Inomata, Toshio; Umezu, Akira; Kajikawa, Makoto; Koibuchi, Hiroshi; Netsu, Nobuhiko.

1986-01-01

In Unit 3 of the Fukushima Nuclear Power Station II (daini), a BWR power plant of output 1,100 MW, commercial operation was started in June 1985. Its start-up test was finished successfully in about nine months. That is, new equipments introduced were demonstration tested. Though the items of testing are increased, the start-up test took short time, resulting in construction period only 54.7 months of the Unit 3, the shortest in the world. During the test, there was no scramming other than the planned. Described are the following: an outline of the Unit 3, the items of its improvement and standardization, including the new equipments, preparations for the start-up test, the start-up test and its evaluation. (Mori, K.)

Consideration of a non-baked start-up of a synchrotron light source

International Nuclear Information System (INIS)

Hori, Y.; Kobayashi, M.

1996-01-01

Vacuum baking of large complex uhv devices, such as synchrotron light sources, requires both careful design and consideration of potential problems regarding the operation and maintenance of the device. Intense synchrotron irradiation can be utilized for degassing; it is indeed necessary to achieve the required operating pressure in most light sources. To examine a non-baked start-up, the outgassing of non-baked chambers by SR irradiation was measured. Also, a non-baked start-up was carried out at the Photon Factory ring. Both results demonstrate the feasibility of a non-baked start-up of a light source. The experiments and results are described, together with several other problems which must be solved for a non-baked start-up. (Author)

Retrieving the thermal diffusivity and effusivity of solids from the same frequency scan using the front photopyroelectric technique

International Nuclear Information System (INIS)

Salazar, Agustín; Oleaga, Alberto; Mendioroz, Arantza; Apiñaniz, Estibaliz

2017-01-01

The photopyroelectric (PPE) technique in the front configuration consists in illuminating one surface of a pyroelectric slab while the other surface is in contact with the test sample. This method has been widely used to measure the thermal effusivity of liquids. Recently, it has been extended to measure the thermal effusivity of solids, by taking into account the influence of the coupling fluid layer used to guarantee the thermal contact. In both cases, the sample (liquid or solid) must be very thick. In this work, we propose a classical frequency scan of a thin sample slab to retrieve the thermal diffusivity and effusivity simultaneously. We use the amplitude and the phase of the front PPE signal, which depend on four parameters: the sample diffusivity and effusivity, the coupling fluid thickness and the coefficient of heat losses. It is demonstrated that the four quantities are not correlated. PPE measurements performed on a set of calibrated solids confirm the ability of the method to obtain the thermal diffusivity and effusivity of solids accurately. (paper)

The start-up processes of academic spin-offs and non-academic ventures

OpenAIRE

Roininen, Sari

2006-01-01

New and small firms are important for the national economic growth, and hence there is a growing interest among policy makers and researchers in understanding the start-up processes among new ventures in order to facilitate more new venture creations. Prior research addressing new ventures' start-up processes focus mainly on the individual behind the venture or different activities in the start-up process. The overall purpose of this study is to increase the understanding of new venture s...

From Jam to Start-up

DEFF Research Database (Denmark)

Bering Kjæhr, Emil; Lyngbye Hvid Jensen, Jane; Schoenau-Fog, Henrik

2015-01-01

the foundation for new start-up companies. There are, however, an even larger group of very creative and innovative games and artifacts with great potential that go unpublished. This potentially leads to a loss of entrepreneurial opportunities and ultimately the jobs and careers such games could have fostered...

Innovative start-ups and young entrepreneurs: Definition of venturem capital and findings from Switzerland

Directory of Open Access Journals (Sweden)

Simon Zaby

2017-02-01

Full Text Available This paper aims to investigate success factors of innovative start-up firms from the perspective of young start-up managers. Which key factors did they experience before and since the foundation of their company? The experience from the quite young Swiss start-up scene pro-vides important insights to entrepreneurs and policy-makers in emerging countries that cur-rently face the necessity of building up a start-up environment. One part of the data has been collected by the author, the other part originates from the Swiss Venture Capital Database (total sample size: 306. The results show a significant role of venture capital financing for the success of innovative start-ups. Interestingly, this is to some extent because the start-ups see various additional benefits from venture capitalists involved in their firm. Thus, the findings shed new light on a proper definition of venture capital that should not solely focus on the flow of funds.

The application of front tracking to the simulation of shock refractions and shock accelerated interface mixing

International Nuclear Information System (INIS)

Sharp, D.H.; Grove, J.W.; Yang, Y.; Boston, B.; Holmes, R.; Zhang, Q.; Glimm, J.

1993-01-01

The mixing behavior of two or more fluids plays an important role in a number of physical processes and technological applications. The authors consider two basic types of mechanical (i.e., non-diffusive) fluid mixing. If a heavy fluid is suspended above a lighter fluid in the presence of a gravitational field, small perturbations at the fluid interface will grow. This process is known as the Rayleigh-Taylor instability. One can visualize this instability in terms of bubbles of the light fluid rising into the heavy fluid, and fingers (spikes) of the heavy fluid falling into the light fluid. A similar process, called the Richtmyer-Meshkov instability occurs when an interface is accelerated by a shock wave. These instabilities have several common features. Indeed, Richtmyer's approach to understanding the shock induced instability was to view that process as resulting from an acceleration of the two fluids by a strong gravitational field acting for a short time. Here, the authors report new results on the Rayleigh-Taylor and Richtmyer-Meshkov instabilities. Highlights include calculations of Richtmyer-Meshkov instabilities in curved geometries without grid orientation effects, improved agreement between computations and experiments in the case of Richtmyer-Meshkov instabilities at a plane interface, and a demonstration of an increase in the Rayleigh-Taylor mixing layer growth rate with increasing compressibility, along with a loss of universality of this growth rate. The principal computational tool used in obtaining these results was a code based on the front tracking method

Reload Startup Physics Tests for Tianwan Nuclear Power station

International Nuclear Information System (INIS)

Yang Xiaoqiang; Li Wenshuang; Li Youyi; Yao Jinguo; Li Zaipeng Jiangsu

2010-01-01

This paper briefly describes the test purposes, test items, test schedules and test equipment's for reload startup physics test's on Unit 1 and 2 of Tianwan Nuclear Power station. Then, an overview of the previous thrice tests and evaluations on the tests results are presented. In the end, the paper shows the development and work direction of optimization project for reload startup physics tests on Unit 1 and 2 of Tianwan Nuclear Power station. (Authors)

Startup and mode competition in a 420 GHz gyrotron

Science.gov (United States)

Qixiang Zhao, A.; Sheng Yu, B.; Tianzhong Zhang, C.

2017-09-01

In the experiments of a 420 GHz second-harmonic gyrotron, it is found that the electron beam voltage and current ranges for single mode operation of TE17.4 are slightly narrower than those in the simulation. To explain this phenomenon, the startup scenario has been investigated with special emphasis on mode competition. The calculations indicate that the decreases of the operating ranges are caused by the voltage overshoot in the startup scenario.

Effects of entrepreneurial orientation on start-up success: A gender perspective

Directory of Open Access Journals (Sweden)

Daisy Mui Hung Kee

2018-06-01

Full Text Available This paper examines the extent to which gender influences on the practice of Entrepreneurial Orien-tation (EO on Start-up Success. This study was conducted among Spin-off and Symbiosis Com-pany (SSC from all sectors in Peninsular Malaysia. Despite the remarkable research on EO and Start-up firms, there is a missing link on how gender provides different perspectives of EO practic-es among SSC, especially in Malaysia. A total of 120 SSC was chosen and the results show that EO was statistically related to Start-up Success and unveiled the magnitude of change that gender possesses in improving the relationship between EO practice and Start-up Success. The major implication of this study presents the unique contribution of gender in motivating SSC owners to engage in EO. Also, the difference of gender perceptions in business provides a variety of untapped opportunities in terms of entrepreneurial-related practices as different gender perceived different needs and capabilities. Future research is suggested to explore this phenomenon more extensively and develop a comprehensive model for the gender analysis. In brief, the discussion in this paper would help to strengthen the body of knowledge on Entrepreneurship and act as a future reference on SSC, EO, and Start-up Success.

Application of Knowledge-Based Techniques to Tracking Function

National Research Council Canada - National Science Library

Farina, A

2006-01-01

...: historical survey of stochastic filtering theory; overview of tracking systems with some details on mono-sensor and multi-sensor tracking, evolution of filtering logics, evolution of correlation logics, and presentation of recent findings on non...

Three Mile Island Startup program and its contributions to plant performance

International Nuclear Information System (INIS)

Brill, R.A.; Barton, J.J.

1976-01-01

The General Public Utilities Service Corporation Startup Organization provided a specialized group for startup testing, coordination, and management of the Three Mile Island Unit No. 1 nuclear power plant. This organization conducted an extensive test program which contributed to Three Mile Island's high first year plant availability

>venture>: Support for Early Stage Start-ups and Potential Entrepreneurs.

Science.gov (United States)

Kauz, Lukas

2014-12-01

>venture>, the leading Swiss-wide business plan competition, is an ideal partner for young start-ups and entrepreneurs. For the upcoming tenth anniversary edition the competition will receive an update. Building upon a successful base of the past nine editions and equipped with contemporary networking events and more know-how transferring seminars, >venture> will fit even better into the Swiss start-up ecosystem.

MECANISMOS DE GERAÇÃO DE EMPREENDIMENTOS: AS ACELERADORAS DE START-UPS NO BRASIL

Directory of Open Access Journals (Sweden)

Amanda Luiza Soares Silva

2018-03-01

Full Text Available Aceleradoras de Start-ups são consideradas mecanismos de geração de empreendimentos. O objetivo geral do estudo é caracterizar as aceleradoras participantes do Programa Nacional de Aceleração de Start-ups – Start-up Brasil. Os principais resultados obtidos foram: perfil das start-ups selecionadas pelas aceleradoras, start-ups em áreas como educação, Tecnologia da Informação e Comunicação – TIC, saúde, economia criativa, entre outras; informações sobre a aceleradora, tais como locais de aceleração (Brasil, Estados Unidos da América – EUA e Suécia e quantidade de start-ups entre 3 e 130 em diversos estágios (pré-aceleradas, em aceleração, aceleradas e no portfólio; o investimento por start-up pode variar entre R$20.000,00 e R$3.000.000,00 e a participação acionária de 1%-40%, dependendo da aceleradora e de seus investidores internos e externos; e, as metodologias de aceleração possuem aspectos como mentoria, visitas técnicas em outros países, eventos, acesso a capital, networking e gestão de portfólios.

Start-up of the ohmic phase in JET

International Nuclear Information System (INIS)

Tanga, A.; Christiansen, J.P.; Cordey, J.G.; Ejima, S.; Kellman, A.; Lazzaro, E.; Lomas, P.J.; Thomas, P.R.

1985-01-01

JET has been designed to permit the study of plasmas in which alphaparticle heating is a significant part of the power balance. In order to have a sufficient thermonuclear yield and to trap the resulting alphaparticles, JET is similar in its dimensions and plasma current to the next generation of reactor-like devices such as NET, FER and INTOR. For this reason, the authors see the results from the study of the start-up of ohmically heated plasmas in JET as highly relevant. Discussed is the range that has been achieved in all major parameters with ohmic heating. Experiences with the wall conditioning technique and the results of ion cyclotron heating experiments in JET are outlined. This paper also describes the stages of plasma formation, current rise and ohmic flat-top

Strategic Management: Business Model Canvas for Start-Up Company

OpenAIRE

Sonninen, Anna

2016-01-01

Thesis is written about development of Kakunpala as a Start-Up Company, because development processes and ideas are the key factors for future success of the company. The aim of this thesis is to understand Strategic Management of the Company and Development processes,by using the SWOT analysis before and after development and by applying Business Model Canvas template to the Start-Up Company, and by describing Customer Journey: what relations Kakunpala has with clients and its processes...

40 CFR 62.15150 - What happens to the operating requirements during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... requirements during periods of startup, shutdown, and malfunction? 62.15150 Section 62.15150 Protection of... § 62.15150 What happens to the operating requirements during periods of startup, shutdown, and... municipal waste combustion unit startup, shutdown, or malfunction. (b) Each startup, shutdown, or...

Lean and global technology start-ups

DEFF Research Database (Denmark)

Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

2015-01-01

In this paper the authors introduce the concept of Lean Global Start-up (LGS) as a way of emphasizing the impossibility for new technology start-ups to deal separately with business development, innovation and early internationalization. For a newly established technology firm the task of being...... global and innovative at the same time should be seen as one process. The paper has two components – an introductory conceptual part and an empirical part that should be considered as basis for the preliminary validation of the conceptual insights. The research sample includes six firms – three from...... Canada and three from Denmark. The firms have had significant problems with the complexity, uncertainties and risks of being innovative on a global scale. They have however found ways of addressing these problems by a disciplined knowledge sharing and IP protection strategy and the efficient use...

Smart or Diverse Start-up Teams?

DEFF Research Database (Denmark)

Hoogendoorn, Sander; Parker, Simon C.; Van Praag, Mirjam

2017-01-01

This paper explores the relationship between cognitive abilities and team performance in a start-up setting. We argue that performance in this setting hinges on three tasks: opportunity recognition, problem solving, and implementation. We theorize that cognitive ability at the individual level has...... others can be assigned to tasks that impose a greater cognitive load (problem solving or opportunity recognition). We present the results of a field experiment in which 573 students in 49 teams started up and managed real companies. We ensured exogenous variation in—otherwise random—team composition...... by assigning students to teams based on their measured cognitive abilities. Each team performed a variety of tasks, often involving complex decision making. The key result of the experiment is that the performance of start-up teams first increases and then decreases with ability dispersion. Strikingly, average...

Prospective Heart Tracking for Whole-heart Magnetic Resonance Angiography

Science.gov (United States)

Moghari, Mehdi H.; Geva, Tal; Powell, Andrew J.

2015-01-01

Purpose To develop a prospective respiratory-gating technique (Heart-NAV) for use with contrast-enhanced 3D inversion recovery (IR) whole-heart magnetic resonance angiography (MRA) acquisitions that directly tracks heart motion without creating image inflow artifact. Methods With Heart-NAV, 1 of the startup pulses for the whole-heart steady-state free precession MRA sequence is used to collect the centerline of k-space, and its 1-dimensional reconstruction is fed into the standard diaphragm-navigator (NAV) signal analysis process to prospectively gate and track respiratory-induced heart displacement. Ten healthy volunteers underwent non-contrast whole-heart MRA acquisitions using the conventional diaphragm-NAV and Heart-NAV with 5 and 10 mm acceptance windows in a 1.5T scanner. Five patients underwent contrast-enhanced IR whole-heart MRA using a diaphragm-NAV and Heart-NAV with a 5 mm acceptance window. Results For non-contrast whole-heart MRA with both the 5 and 10 mm acceptance windows, Heart-NAV yielded coronary artery vessel sharpness and subjective visual scores that were not significantly different than those using a conventional diaphragm-NAV. Scan time for Heart-NAV was 10% shorter (p<0.05). In patients undergoing contrast-enhanced IR whole-heart MRA, inflow artifact was seen with the diaphragm-NAV but not with Heart-NAV. Conclusion Compared to a conventional diaphragm-NAV, Heart-NAV achieves similar image quality in a slightly shorter scan time and eliminates inflow artifact. PMID:26843458

Modelling and evaluating customer loyalty using neural networks: Evidence from startup insurance companies

Directory of Open Access Journals (Sweden)

Azarnoush Ansari

2016-06-01

Full Text Available The purpose of this study is to investigate the customer–service provider relationship in the insurance industry using artificial neural networks and linear regression. Using a sample of 389 customers from 10 different startup insurance companies, it was found that artificial neural networks are an efficient way to evaluate the factors affecting customer loyalty. The results indicated that customer satisfaction and perceived value are significant predictors of customer loyalty. Additionally, it was found that trust, perceived quality, and empathy have a significant impact on both customer satisfaction and perceived value. The results also showed that customer commitment to service provider is positively associated with customer satisfaction and loyalty. After comparing the performance of linear regression models with artificial neural networks, it was found that the use of neural networks is a better approach for analyzing the customer loyalty, satisfaction, and perceived value. The use of new techniques such as artificial neural networks for analyzing the customer behavior can be particularly beneficial for startup companies who aspire to gain competitive advantage over their strong and well-established rivals.

Translations on Eastern Europe, Political, Sociological and Military Affairs, Number 1579

Science.gov (United States)

1978-08-23

front of the bridge abutments . The weight-volume ratio was so selected that the rail girders and the road- way or track plates would float in the...respect to the required posi- tion. 2-3 Abutment with Highway Connection ThP abutment , in its silkiest form, consists of a railroad tie stack; but...it c£ Sso be built up of massive prefabricated parts or locally prepared concrete. A portion of the start-up approach/ and braking forces is di

Implementation Of Code And Carrier Tracking Loops For Software GPS Receivers

Directory of Open Access Journals (Sweden)

Win Kay Khaing

2015-06-01

Full Text Available Abstract GPS is playing in very important role in our modern mobile societies. Software approach is very flexible rather than the traditional hardware receivers. The soft-GPS receiver includes two portions hardware and software. In hardware portion an antenna filter down-converter from RF Radio Frequency to IF Intermediate Frequency and an ADC Analog to Digital Converter are included. In software portion signal processing such as acquisition tracking and navigation that runs on general purpose processor is included. The GPS signal is taken from N-FUELS Full Educational Library of Signals for Navigation signal simulator. The heart of soft-GPS receiver is the synchronization processes such as acquisition and tracking. In tracking there are two main loops for code and carrier tracking. The objective of this paper is to analyse and find the optimum discriminator function for the code tracking loop in soft-GPS receivers. The delay lock loop DLL is a well-known technique to track the codes for GNSS spread spectrum systems. This paper also presents non-coherent square law DLLs and the impacts of some parameters on DLL discriminators such as number of samples per chip early-late spacing different C No values where C denotes the signal power and No is the noise spectral density and the impact of with or without front-end device. The results of discriminator outputs are illustrated by using S-curves. Testing results with the real GPS signal are also described. This optimized discriminator functions can be implemented in any soft-GPS receivers.

Assessment of the plasma start-up in Wendelstein 7-X with neutral beam injection

International Nuclear Information System (INIS)

Gradic, D.; Dinklage, A.; Brakel, R.; McNeely, P.; Rust, N.; Wolf, R.; Osakabe, M.

2015-01-01

Plasma start-up by neutral beam injection was investigated for stellarators. A zero-dimensional collisional model was extended to evaluate the temporal evolution of the plasma start-up in a confining toroidal magnetic field. Inclusion of different beam energy components indicated a substantial effect due to the energy dependence of beam–gas collisions. Additional collision processes and particle equations were considered to simulate the plasma start-up in helium–hydrogen mixtures. The isotope effect between operation with hydrogen and deuterium beams was also investigated. As a major objective the conditions necessary for a plasma start-up with neutral beams in W7-X have been examined. The assessed beam configuration in W7-X was found not to allow plasma start-up by neutral beam injection alone. The model has been validated for experimental data from W7-AS and Large Helical Device. Quantitative predictions of this study show that the ratio of the beam–plasma interaction length and the plasma volume is an essential quantity for the successful plasma start-up with neutral beams. (paper)

40 CFR 60.1695 - What happens to the operating requirements during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... requirements during periods of startup, shutdown, and malfunction? 60.1695 Section 60.1695 Protection of... Requirements § 60.1695 What happens to the operating requirements during periods of startup, shutdown, and... municipal waste combustion unit startup, shutdown, or malfunction. (b) Each startup, shutdown, or...

Reliability assessment of PARR-1 renovated I and C system startup channel-b

Energy Technology Data Exchange (ETDEWEB)

Qamar, M.A.; Habib, M.A.; Iqbal, M.

1991-11-20

The report covers the reliability assessment of the startup channel-B of the PARR-1 renovated instrumentation and Control. For startup channel-A, a separate report (DNSRP-10(7)/88) was prepared in 1988. As the modules are of different origins in both the channels, a separate calculation was necessary. In the report the overall unreliability of the startup channel has been calculated by considering 1 out of 2 operation mode. In the assessment, the reliability calculations for the channel has been performed using similar assumptions as used in the authors' report on startup channel-A. For the analysis the Component Count Method (CCM) was applied. Comparison of results for channel-A and channel-B were made.

Detection of a faint fast-moving near-Earth asteroid using the synthetic tracking technique

Energy Technology Data Exchange (ETDEWEB)

Zhai, Chengxing; Shao, Michael; Nemati, Bijan; Werne, Thomas; Zhou, Hanying; Turyshev, Slava G.; Sandhu, Jagmit [Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Drive, Pasadena, CA 91109 (United States); Hallinan, Gregg; Harding, Leon K., E-mail: chengxing.zhai@jpl.nasa.gov [Department of Astronomy, California Institute of Technology, 1200 East California Boulevard, Pasadena, CA 91125 (United States)

2014-09-01

We report a detection of a faint near-Earth asteroid (NEA) using our synthetic tracking technique and the CHIMERA instrument on the Palomar 200 inch telescope. With an apparent magnitude of 23 (H = 29, assuming detection at 20 lunar distances), the asteroid was moving at 6.°32 day{sup –1} and was detected at a signal-to-noise ratio (S/N) of 15 using 30 s of data taken at a 16.7 Hz frame rate. The detection was confirmed by a second observation 77 minutes later at the same S/N. Because of its high proper motion, the NEA moved 7 arcsec over the 30 s of observation. Synthetic tracking avoided image degradation due to trailing loss that affects conventional techniques relying on 30 s exposures; the trailing loss would have degraded the surface brightness of the NEA image on the CCD down to an approximate magnitude of 25 making the object undetectable. This detection was a result of our 12 hr blind search conducted on the Palomar 200 inch telescope over two nights, scanning twice over six (5.°3 × 0.°046) fields. Detecting only one asteroid is consistent with Harris's estimates for the distribution of the asteroid population, which was used to predict a detection of 1.2 NEAs in the H-magnitude range 28-31 for the two nights. The experimental design, data analysis methods, and algorithms are presented. We also demonstrate milliarcsecond-level astrometry using observations of two known bright asteroids on the same system with synthetic tracking. We conclude by discussing strategies for scheduling observations to detect and characterize small and fast-moving NEAs using the new technique.

An analysis of reactivity prediction during the reactor start-up process

International Nuclear Information System (INIS)

Bajgl, Josef; Krysl, Vaclav; Svarny, Jiri

2015-01-01

The different VVER-440 core fuel loadings subcriticality evaluations are performed during the start-up process by boron dilution or control assembly withdrawn by macrocode MOBY-DICK calculations. The dynamic reactivity and quasicritical reactivity are compared and sensitivity of reactivity prediction at the low boundary of start-up interval (ρ = -0,01) has been provided on the basis of different modelling of ionization chamber (IC) response calculation. Special attention is paid to the impact of power distribution and spontaneous fission distribution form factor on IC response correction during control assembly movement. Precision and robustness of different corrections of IC signal processing in real core start-up processed IC signals was evaluated.

78 FR 38001 - Reconsideration of Certain Startup/Shutdown Issues: National Emission Standards for Hazardous Air...

Science.gov (United States)

2013-06-25

..., FRL-9827-1] RIN 2060-AR62 Reconsideration of Certain Startup/Shutdown Issues: National Emission... published in the Federal Register the proposed rule, ``Reconsideration of Certain New Source and Startup....'' That proposal opened for reconsideration certain issues, including those related to startup and...

Accelerating Research Innovation by Adopting the Lean Startup Paradigm

Directory of Open Access Journals (Sweden)

Kaisa Still

2017-05-01

Full Text Available Converting scientific expertise into marketable products and services is playing an increasingly important role in the launching of new ventures, the growth of existing firms, and the creation of new jobs. In this article, we explore how the lean startup paradigm, which validates the market for a product with a business model that can sustain subsequent scaling, has led to a new process model to accelerate innovation. We then apply this paradigm to the context of research at universities and other research organizations. The article is based on the assumption that the organizational context matters, and it shows how a deeper understanding of the research context could enable an acceleration of the innovation process. We complement theoretical examples with a case example from VTT Technical Research Institute of Finland. Our findings show that many of the concepts from early-acceleration phases – and the lean startup paradigm – can also be relevant in innovation discussions within the research context. However, the phase of value-proposition discovery is less adequately addressed, and that of growth discovery, with its emphasis on building on a scalable, sustainable business does not seem to be addressed with the presented innovation approaches from the research context. Hence, the entrepreneurial activities at the research context differ from those in startups and internal startups in established organizations.

Effect of Start-Up Strategies and Electrode Materials on Carbon Dioxide Reduction on Biocathodes.

Science.gov (United States)

Saheb-Alam, Soroush; Singh, Abhijeet; Hermansson, Malte; Persson, Frank; Schnürer, Anna; Wilén, Britt-Marie; Modin, Oskar

2018-02-15

with biocathodes could be used to reduce CO 2 to methane, acetate, or other high-value chemicals. The technique can be used to convert solar energy to chemicals. However, enriching biocathodes that are capable of CO 2 reduction is more difficult and less studied than enriching bioanodes. The effect of different start-up strategies and electrode materials on the microbial communities that are enriched on biocathodes has not been studied. The purpose of this study was to investigate two different start-up strategies and three different electrode materials for start-up and long-term operation of biocathodes capable of reducing CO 2 to valuable biochemicals. Copyright © 2018 Saheb-Alam et al.

Predictive modelling for startup and investor relationship based on crowdfunding platform data

Science.gov (United States)

Alamsyah, Andry; Buono Asto Nugroho, Tri

2018-03-01

Crowdfunding platform is a place where startup shows off publicly their idea for the purpose to get their project funded. Crowdfunding platform such as Kickstarter are becoming popular today, it provides the efficient way for startup to get funded without liabilities, it also provides variety project category that can be participated. There is an available safety procedure to ensure achievable low-risk environment. The startup promoted project must accomplish their funded goal target. If they fail to reach the target, then there is no investment activity take place. It motivates startup to be more active to promote or disseminate their project idea and it also protect investor from losing money. The study objective is to predict the successfulness of proposed project and mapping investor trend using data mining framework. To achieve the objective, we proposed 3 models. First model is to predict whether a project is going to be successful or failed using K-Nearest Neighbour (KNN). Second model is to predict the number of successful project using Artificial Neural Network (ANN). Third model is to map the trend of investor in investing the project using K-Means clustering algorithm. KNN gives 99.04% model accuracy, while ANN best configuration gives 16-14-1 neuron layers and 0.2 learning rate, and K-Means gives 6 best separation clusters. The results of those models can help startup or investor to make decision regarding startup investment.

Start-up of a UASB effluent treatment plant on distillery wastewater ...

African Journals Online (AJOL)

This paper reports on the seasonal operation of a UASB treatment plant treating a distillery wastewater stream with particular focus on seasonal start-up conditions after the first process commissioning. The start-up period was typically one week before process stability could be achieved. It is recommended that the loading ...

Help Wanted: Exploring the Value of Entrepreneurial Mentoring at Start-Up

Science.gov (United States)

Brodie, Jacqueline; Van Saane, Sebastiaan Huib; Osowska, Renata

2017-01-01

The purpose of the research presented in this article was to investigate the added value of mentoring for entrepreneurs during the start-up phase. This small-scale exploratory research focused on five start-up entrepreneurs in Scotland to determine the entrepreneurs' perceptions regarding the "added" value of their mentoring support. To…

Navigating the Interface between Design Education and Fashion Business Start-up

Science.gov (United States)

Mills, Colleen E.

2012-01-01

Purpose: The purpose of this paper is to address the interface between design education and business start-up in the designer fashion industry (DFI) and provide a new framework for reflecting on ways to improve design education and graduates' business start-up preparedness. Design/methodology/approach: This interpretive study employed…

Start-up of anaerobic digestion of source-sorted organic municipal solid waste

International Nuclear Information System (INIS)

Maroun, Rania

2004-01-01

Municipal solid waste (MSW) disposal is a major environmental concern worldwide. Among the environmentally sound technologies for the treatment of MSW, composting in the form of anaerobic digestion (AD) appears as a suitable alternative that offers the advantage of rapid stabilization of organic matter, reduction in waste volume, production of methane, and minimal environmental impacts in comparison to land filling and incineration. Yet, although outstanding advances in anaerobic digestion of solid substrate have been made in the last 10 years, some development areas are lagging, including the fast and reliable process start-up in terms of type of inocula and overall start-up strategies. The present study investigates the start-up and operation of bench-scale anaerobic digesters treating the source-sorted organic fraction of municipal solid waste. The experimental program consisted of starting up two digesters in parallel. Three consecutive interventions in the start-up program were implemented to achieve steady state. Start-up was relatively slow indicating the seed obtained from an operating anaerobic wastewater treatment plant was not suitable. The use of cattle manure together with effluent dilution reduced the acclimation period (Author.)

40 CFR 60.1220 - What happens to the emission limits during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... during periods of startup, shutdown, and malfunction? 60.1220 Section 60.1220 Protection of Environment... Emission Limits § 60.1220 What happens to the emission limits during periods of startup, shutdown, and... waste combustion unit startup, shutdown, or malfunction. (b) Each startup, shutdown, or malfunction must...

Level Diagrams analysis of Pareto Front for multiobjective system redundancy allocation

International Nuclear Information System (INIS)

Zio, E.; Bazzo, R.

2011-01-01

Reliability-based and risk-informed design, operation, maintenance and regulation lead to multiobjective (multicriteria) optimization problems. In this context, the Pareto Front and Set found in a multiobjective optimality search provide a family of solutions among which the decision maker has to look for the best choice according to his or her preferences. Efficient visualization techniques for Pareto Front and Set analyses are needed for helping decision makers in the selection task. In this paper, we consider the multiobjective optimization of system redundancy allocation and use the recently introduced Level Diagrams technique for graphically representing the resulting Pareto Front and Set. Each objective and decision variable is represented on separate diagrams where the points of the Pareto Front and Set are positioned according to their proximity to ideally optimal points, as measured by a metric of normalized objective values. All diagrams are synchronized across all objectives and decision variables. On the basis of the analysis of the Level Diagrams, we introduce a procedure for reducing the number of solutions in the Pareto Front; from the reduced set of solutions, the decision maker can more easily identify his or her preferred solution.

Building Dynamic Capabilities in Web Startups: An Empirical Study of Norwegian Web Startups

OpenAIRE

Sahlen, Martin Abelson; Gran-Jansen, Sigurd; Rygh, Mathias

2014-01-01

Purpose: This thesis explores how web startups operating in a crowded, fast-moving and highly competitive marketplace can gain competitive advantage through building dynamic capabilities and what these capabilities consist of. Design/methodology/approach: Firstly, insight was obtained through reviewing key themes within classic resource based theory and entrepreneurship theory. Newer empirical research on entrepreneurial success factors, as well as popular science and advice given by expert w...

GUERRILLA MARKETING : A creative marketing method for start-ups

OpenAIRE

Zujewska, Barbara

2014-01-01

The objective of this thesis work was to introduce guerrilla marketing as a valuable marketing method for small and medium size startup companies. The thesis presents the theoretical studies on the subject based on literature and case studies. The practical use of the theory is demonstrated in the marketing plan based on guerrilla marketing approach. The marketing plan was written based on the example of an existing startup company, mCASH. The company is located in Oslo, Norway. The thesis...

Power in a startup's relationships with its established partners : Interactions between structural and behavioural power

NARCIS (Netherlands)

Oukes, Tamara; von Raesfeld Meijer, Ariane; Groen, Aard

2017-01-01

Power plays a key role in the relationships between startups and established organisations. Yet researchers have devoted little attention to the startup's perspective on power in such relationships. To study startups' view on power, a useful starting point is their structural power, but this also

77 FR 73968 - Reconsideration of Certain New Source and Startup/Shutdown Issues: National Emission Standards...

Science.gov (United States)

2012-12-12

...; FRL-9762-1] RIN 2060-AR62 Reconsideration of Certain New Source and Startup/Shutdown Issues: National... Source and Startup/Shutdown Issues: National Emission Standards for Hazardous Air Pollutants from Coal... November 30, 2012, proposed ``Reconsideration of Certain New Source and Startup/Shutdown Issues: National...

The Impact of Digitalization on the Speed of Internationalization of Lean Global Startups

Directory of Open Access Journals (Sweden)

Michael Neubert

2018-05-01

Full Text Available Lean global startups need to internationalize early and fast. The digitalization of new foreign market development helps them to more efficiently identify new market opportunities in global markets. With this approach, they are saving resources while developing the most attractive markets. This article examines how lean global startups develop new foreign markets more rapidly due to digitalization. Thus, the aim is to understand the impact of digitalization on speed of internationalization of lean global startups. The study addresses a gap in the scholarly literature and a practical need to evaluate new foreign markets and business opportunities more quickly and more regularly and to understand what helps lean global startups react more quickly to opportunities and threats with respect to changing market attractiveness. Furthermore, it outlines why and how digitalization is important throughout the internationalization process. The research followed a multiple case-study design using different sources of evidence, including 73 interviews with senior managers of lean global startups. The findings reveal that digitalization allows lean global startups to increase decision-making efficiency and to optimize strategies and processes for evaluating international markets. The findings suggest that lean global startups can benefit from the use of digital technologies by applying a more efficient foreign market development process with regular reviews and a reduced workflow, by faster mediation between local market realities and strategic goals, by analyzing all foreign markets instead of just a sample of them, and by optimizing decision-making processes including the ability to make long-term, strategic decisions due to better market information.

Start-up Success in a Small Island State: A Study among Entrepreneurs in Malta

Directory of Open Access Journals (Sweden)

Leonie Baldacchino

2008-05-01

Full Text Available This study focuses on entrepreneurs in the small island state of Malta and investigates whether starting up and running an enterprise is facilitated or hindered by being in a small island environment. Specifically it asks (1 whether being on a small island, on the periphery of a major market facilitates or hinders entrepreneurship and start-up success; (2 whether Malta’s cultural context and enterprise environment affect entrepreneurship and start-up success; (3 what the key success factors among Maltese start-ups are; and (4 how are creativity and innovation reflected in Maltese start-ups. Qualitative research among 13 start-ups is supported by telephone-based research among a sample of 90 respondents. Findings contribute to the pool of business expertise and context-specific information from small island states that is often missing from the international literature.

Human tracking over camera networks: a review

Science.gov (United States)

Hou, Li; Wan, Wanggen; Hwang, Jenq-Neng; Muhammad, Rizwan; Yang, Mingyang; Han, Kang

2017-12-01

In recent years, automated human tracking over camera networks is getting essential for video surveillance. The tasks of tracking human over camera networks are not only inherently challenging due to changing human appearance, but also have enormous potentials for a wide range of practical applications, ranging from security surveillance to retail and health care. This review paper surveys the most widely used techniques and recent advances for human tracking over camera networks. Two important functional modules for the human tracking over camera networks are addressed, including human tracking within a camera and human tracking across non-overlapping cameras. The core techniques of human tracking within a camera are discussed based on two aspects, i.e., generative trackers and discriminative trackers. The core techniques of human tracking across non-overlapping cameras are then discussed based on the aspects of human re-identification, camera-link model-based tracking and graph model-based tracking. Our survey aims to address existing problems, challenges, and future research directions based on the analyses of the current progress made toward human tracking techniques over camera networks.

First physical start-up for the first pulsed reactor in China

International Nuclear Information System (INIS)

Huang Wenlou; Tan Rilin; Xie Yuqi; Chai Songshan; Li Yingfa; He Qianming; Zhou Bin

1993-01-01

The characteristics and the test results of initial loading fuel and first physical start-up for the first pulsed reactor in China (PRC-1) are described. Safe measure to ensure safety of first physical start-up are also described. The experiments show that performances of PRC-1 are in accord with design requirements

Leadership toward Creativity in Virtual Work in a Start-Up Context

Science.gov (United States)

Humala, Iris Annukka

2015-01-01

Purpose: This paper aims to better understand how to lead toward creativity in virtual work in a start-up context. Design/methodology/approach: The study investigates the participants' experiences about the learning challenges in leadership toward creativity in virtual work in a start-up company and the meanings attributed to their experiences,…

Radioactive Particle Tracking (RPT): The Powerful Industrial Radiotracer Techniques for Hydrodynamics and Flow Visualization Studies

International Nuclear Information System (INIS)

Mohd Amirul Syafiq Mohd Yunos

2016-01-01

Full text: Radioactive particle tracking (RPT) techniques have been widely applied in the field of chemical engineering, especially in hydrodynamics in multiphase reactors. This technique is widely used to monitor the motion of the flow inside a reactor by using a single radioactive particle tracer that is neutrally buoyant with respect to the phase is used as a tracker. The particle moves inside the volume of interest and its positions are determined by an array of scintillation detectors counting in coming photons. Particle position reconstruction algorithms have been traditionally used to map measured counts rate into the coordinates by solving a minimization problem between measured events and calibration data. RPT have been used to validate respective-scale CFD models to partial success. This presentation described an introduction to radioactive particle tracking and summarizing a history of such developments and the current state of this method in Malaysian Nuclear Agency, with a perspective towards the future and how these investigations may help scale-up developments. (author)

Mathematical modeling and analysis of heat pipe start-up from the frozen state

International Nuclear Information System (INIS)

Jang, J.H.; Faghri, A.; Chang, W.S.; Mahefkey, E.T.

1989-08-01

The start-up process of a frozen heat pipe is described and a complete mathematical model for the start-up of the frozen heat pipe is developed based on the existing experimental data, which is simplified and solved numerically. The two-dimensional transient model for the wall and wick is coupled with the one-dimensional transient model for the vapor flow when vaporization and condensation occur at the interface. A parametric study is performed to examine the effect of the boundary specification at the surface of the outer wall on the successful start-up from the frozen state. For successful start-up, the boundary specification at the outer wall surface must melt the working substance in the condenser before dry-out takes place in the evaporator

Urbanization and start-up rates in different geographies: Belgium, the Netherlands and Sweden

OpenAIRE

Hans, Lianne; Koster, Sierdjan

2017-01-01

This study addresses the mediating role of settlement patterns in the relationship between urbanization and start-up activity. Places do not operate in a vacuum and to understand the effect of 'own' density on start-up patterns, we need to account for the urban spillovers or borrowed size that they may experience from other places nearby. The results can explain the empirical ambiguity in the relationship between urbanization and start-up patterns: the relationship between urbanization and st...

The Impact of Start-up Grants on Firm Performance in Estonia

Directory of Open Access Journals (Sweden)

Siret Vildo

2013-01-01

Full Text Available As in economic theory start-up enterprises have been seen as important sources of growth, the government support measures to enterprises have been a common practice around the world for decades. As the governmental support to enterprises is often of a considerable amount of money there is a need to assess its efficiency. In the present article we study the impact of Estonian start-up grants distributed in 2002 and 2003 on various indicators of firm performance with econometric methods, namely propensity score matching. We use the data from the Estonian Business Register in order to study the impact of start-up grants on various economic indicators like the number of employees, turnover, equity, fixed assets and firm survival. The results showed that the start-up grants proved to affect positively the number of employed people and turnover, yet the impact on productivity was negative. One implication of the study is that it is difficult to achieve different goals to the same extent with a single governmental grant

Start-up of plasma current by electron Bernstein wave

International Nuclear Information System (INIS)

Maekawa, Takashi; Tanaka, Hitoshi; Uehide, Masaki

2009-01-01

Electron cyclotron current drive by electron Bernstein (EB) waves for the start-up and ramp-up of toroidal plasma current with no central solenoid in tokamaks is discussed. It is shown that high N// EB waves have ability to ramp-up the current against the counter voltage from self-induction, where N// is the parallel refractive index to the magnetic field, and they are especially suitable for initial current start-up phase where the bulk electron temperature is low enough to ensure high N// EB waves. (author)

Female Hires and the Success of Start-up Firms

OpenAIRE

Weber, Andrea; Zulehner, Christine

2009-01-01

In this paper we investigate the relationship between females among the first hires of start-up companies and business success. Our results show that firms with female first hires have a higher share of female workers at the end of the first year after entry. Further, we find that firms with female first hires are more successful and stay longer in the market. We conclude that our results support the hypothesis that gender-diversity in leading positions is an advantage for start-up firms.

Recent applications of nuclear track emulsion technique

Energy Technology Data Exchange (ETDEWEB)

Zarubin, P. I., E-mail: zarubin@lhe.jinr.ru [Joint Institute for Nuclear Research, Veksler and Baldin Laboratory of High Energy Physics (Russian Federation)

2016-12-15

A survey of recent results obtained using the nuclear track emulsion (NTE) technique in low energy applications is given. NTE irradiation with 60 MeV {sup 8}He nuclei provides identification of their decays at stopping, evaluation of the possibility of α range spectrometry, and observation of drift of thermalized {sup 8}He atoms. Correlations of α particles studied in {sup 12}C → 3α splitting induced by 14.1 MeV neutrons indicate the presence of a superposition of 0{sup +} and 2{sup +} states of the {sup 8}Be nucleus in the ground state of {sup 12}C. Angular correlations of fragments are studied in boron-enriched NTE, and the prospects of NTE application in radioactivity and nuclear fission research are discussed. It is proposed to use an automated microscope to search for collinear tripartition of heavy nuclei implanted in NTE. Surface irradiation of NTE by a {sup 252}Cf source is started. Planar events containing fragment pairs and long range α particles, as well as fragment triples, are studied. NTE samples are calibrated using Kr and Xe ions with an energy of 1.2 and 3 A MeV.

Uranium exploration techniques

International Nuclear Information System (INIS)

Nichols, C.E.

1984-01-01

The subject is discussed under the headings: introduction (genetic description of some uranium deposits; typical concentrations of uranium in the natural environment); sedimentary host rocks (sandstones; tabular deposits; roll-front deposits; black shales); metamorphic host rocks (exploration techniques); geologic techniques (alteration features in sandstones; favourable features in metamorphic rocks); geophysical techniques (radiometric surveys; surface vehicle methods; airborne methods; input surveys); geochemical techniques (hydrogeochemistry; petrogeochemistry; stream sediment geochemistry; pedogeochemistry; emanometry; biogeochemistry); geochemical model for roll-front deposits; geologic model for vein-like deposits. (U.K.)

Deaerating operation during startup periods in Japanese BWRs

International Nuclear Information System (INIS)

Maeda, K.

2002-01-01

The IGSCC has been mitigated by application of effective countermeasures on water chemistry environment. Hydrogen water chemistry (HWC) has been implemented to reduce the reactor water dissolved oxygen concentration and electrochemical corrosion potential (ECP) during plant operation to reduced crack growth rate of in sensitized stainless steel. But the HWC has not been implemented during startup periods. The crack growth rate of sensitized stainless steel will increase obviously during startup period by increasing in temperature under high dissolved oxygen conditions [1]. The deaerating operation has been applied routinely in Japanese BWRs to reduce reactor water dissolved oxygen quickly and easily before plant startup [2,3]. The main condenser is vacuumed up before start in the deaerating operation. The reactor is connected with the main condenser by opening the main steam bypass valves or the main steam drain valves. The deaerating operation is started with keeping the reactor water temperature about 70 to 90 degrees centigrade. The deaerating operation will come to an end when the reactor water dissolved concentration will decrease below 200 ppb. This paper shows the procedure and actual results of deaerating operation. (authors)

Tokamak startup with electron cyclotron heating

International Nuclear Information System (INIS)

Holly, D.J.; Prager, S.C.; Shepard, D.A.; Sprott, J.C.

1980-04-01

Experiments are described in which the startup voltage in a tokamak is reduced by approx. 60% by the use of a modest amount of electron cyclotron resonance heating power for preionization. A 50% reduction in volt-second requirement and impurity reflux are also observed

Tokamak startup with electron cyclotron heating

Energy Technology Data Exchange (ETDEWEB)

Holly, D J; Prager, S C; Shepard, D A; Sprott, J C

1980-04-01

Experiments are described in which the startup voltage in a tokamak is reduced by approx. 60% by the use of a modest amount of electron cyclotron resonance heating power for preionization. A 50% reduction in volt-second requirement and impurity reflux are also observed.

Laser startup optics for Baseball II and future mirror machines

International Nuclear Information System (INIS)

Frank, A.M.; Chargin, A.K.; Brown, N.J.

1975-01-01

The laser startup system for Baseball II-T uses a 300-J CO 2 laser to hit a 100-μ diameter pellet with a laser power density on the order of 10 13 W/cm 2 . The laser is a 20-cm diameter unstable resonator transversely excited (TEA) oscillator. The beam is split and then focused using off-axis parabolas. The symmetric configuration and central obscuration of the CO 2 beam allow coaxial alignment and pellet detection optics. This experiment primarily uses commercially available systems and components. Optical elements were fabricated both by direct machining and standard polishing techniques. The laser and optical systems are directly scalable to reactor requirements using demonstrated technologies

Study on ECH-assisted start-up using trapped particle configuration in KSTAR and application to ITER

Science.gov (United States)

Lee, Jeongwon; Kim, Jayhyun; An, YoungHwa; Yoo, Min-Gu; Hwang, Y. S.; Na, Yong-Su

2017-12-01

ECH-assisted start-up using trapped particle configuration (TPC) is firstly studied in a superconducting, conventional tokamak, KSTAR. First, improved and efficient start-up using TPC than conventional field null configuration (FNC) is achieved by enhanced pre-ionization plasma quality. TPC shows the broader operation window in terms of the poloidal field quality and the deuterium prefill pressure than that of FNC. Surprisingly the particle trapping enhances the plasma start-up performance even with much lower particle trapping ratio than that of spherical torus. Reliability of TPC with low trapping ratio is investigated by 0D plasma evolution code, TECHP0D. Second, the characteristics of TPC start-up are explored with experiments and modellings. Two kind of start-up failure conditions are identified by the magnetic pitch and prefill pressure scan experiments: (i) low ionization rate; and (ii) low density condition. These experimental observation has consistency with TECHP0D modeling result. Finally, reliable ITER-relevant low toroidal electric field start-up using TPC is achieved with drastically improved success rate of start-up in KSTAR. In this experiments, validity of the ITER-like toroidally inclined ECH/ECCD injection is also expected. Time dependent ITER start-up scenario using TPC is proposed and the superiority of it than FNC is discussed.

An Integrated Start-Up Method for Pumped Storage Units Based on a Novel Artificial Sheep Algorithm

Directory of Open Access Journals (Sweden)

Zanbin Wang

2018-01-01

Full Text Available Pumped storage units (PSUs are an important storage tool for power systems containing large-scale renewable energy, and the merit of rapid start-up enable PSUs to modulate and stabilize the power system. In this paper, PSU start-up strategies have been studied and a new integrated start-up method has been proposed for the purpose of achieving swift and smooth start-up. A two-phase closed-loop startup strategy, composed of switching Proportion Integration (PI and Proportion Integration Differentiation (PID controller is designed, and an integrated optimization scheme is proposed for a synchronous optimization of the parameters in the strategy. To enhance the optimization performance, a novel meta-heuristic called Artificial Sheep Algorithm (ASA is proposed and applied to solve the optimization task after a sufficient verification with seven popular meta-heuristic algorithms and 13 typical benchmark functions. Simulation model has been built for a China’s PSU and comparative experiments are conducted to evaluate the proposed integrated method. Results show that the start-up performance could be significantly improved on both indices on overshoot and start-up, and up to 34%-time consumption has been reduced under different working condition. The significant improvements on start-up of PSU is interesting and meaning for further application on real unit.

Standardization of the time for the execution of HANARO start-up and shutdown procedures

International Nuclear Information System (INIS)

Choi, H. Y.; Lim, I. C.; Hwang, S. R.; Kang, T. J.; Youn, D. B.

2003-01-01

For the standardization of the time to execute HANARO start-up and shutdown procedures, code names were assigned to the individual procedures and the work time were investigated. The data recorded by the operators during start-up and shutdown were statistically analyzed. The analysis results will be used for the standardization of start-up and shutdown procedures and it will be reflected in the procedure document

Start-up emissions from residential down-draught wood log boilers

Energy Technology Data Exchange (ETDEWEB)

Pettersson, E. (Luleaa Univ. of Technology (Sweden). Energy Technology Centre in Piteaa), Email: esbjorn.pettersson@ltu.se

2009-07-01

Start-up emissions can be substantial and even dominating in real use. There are few published investigations regarding the relative importance of different parameters on the start-up emissions. It has though recently been stated that for down-draught boilers, best results are achieved if the wood charge is ignited fairly close to the secondary chamber. The objective of the experimental work was to evaluate the effect of different fuel and design parameters on the start-up emissions, using experimental design which enables a direct comparison between different parameters, using three levels of preheating of secondary air, electric preheating of primary air, different moisture and size of the start wood as well as different amounts of birch bark, which was used to spread the fire during the start. The boiler did not use a bypass damper and the full fuel charge was added before igniting the start wood through an ignition door situated slightly above the grate. The only significant results for the four parameters were that smaller and drier start wood gave lower start-up emissions. Extra amount of birch bark gave the same result. The most important parameters are the fuel parameters, which mean that the result is generally applicable. (orig.)

The Measurement of cloud velocity using the pulsed laser and image tracking technique

Energy Technology Data Exchange (ETDEWEB)

Kwon, Seong-Ouk; Baik, Seung-Hoon; Park, Seung-Kyu; Park, Nak-Gyu; Kim, Dong-lyul; Ahn, Yong-Jin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

The height of the clouds is also important for the three dimensional radiative interaction of aerosols and clouds, since the radiative effects vary strongly depending whether the cloud is above, below or even embedded in an aerosol layer. Clouds play an important role in climate change, in the prediction of local weather, and also in aviation safety when instrument assisted flying is unavailable. Presently, various ground-based instruments used for the measurements of the cloud base height or velocity. Lidar techniques are powerful and have many applications in climate studies, including the clouds' temperature measurement, the aerosol particle properties, etc. Otherwise, it is very circumscribed in cloud velocity measurements In this paper, we propose a new method to measure the cloud velocity. In this paper, we presented a method for the measurement of the cloud altitude and velocity using lidar's range detection and the tracking system. For the lidar system, we used an injection-seeded pulsed Nd:YAG laser as the transmitter to measure the distance to the target clouds. We used the DIC system to track the cloud image and calculate the actual displacement per unit time. The configured lidar system acquired the lidar signal of clouds at a distance of about 4 km. The developed fast correlation algorithm of the tracking, which is used to track the fast moving cloud relatively, was efficient for measuring the cloud velocity in real time. The measurement values had a linear distribution.

Transient CFD simulation of a Francis turbine startup

International Nuclear Information System (INIS)

Nicolle, J; Morissette, J F; Giroux, A M

2012-01-01

To assess the life expectancy of hydraulic turbines, it is essential to obtain the loading on the blades, especially during transient operations known to be the most damaging. This paper presents a simplified CFD setup to model the startup phase of a Francis turbine while it goes from rest to speed no-load condition. The fluid domain included one distributor sector coupled with one runner passage. The guide vane motion and change in the angular velocity were included in a commercial code with user functions. Comparisons between numerical results and measurements acquired on a full-size turbine showed that most of the flow physics occurring during startup were captured.

Redox fronts

International Nuclear Information System (INIS)

Chapman, N.; McKinley, I.; Shea, M.; Smellie, J.

1993-01-01

This article describes the investigations of redox fronts performed at the Osamu Utsumi mine. Results obtained by modelling groups on the rate of movement of the redox fronts and on the chemical reactions involved are discussed. Some of the most important rockwater interactions which occur at redox fronts can be modelled reasonably well but the complex redox chemistry of elements like sulphur is poorly simulated. The observed enrichment of many trace elements close to the redox fronts could be of significance for high-level waste repositories, but cannot be quantified by existing models. (author) 6 figs., 1 tab

Summary revaluation of energetic start-up of the unit 1 of nuclear power plant Mochovce

International Nuclear Information System (INIS)

Sarvaic, I.; Miskolci, M.

1998-01-01

The document contents stage revaluation of energetic start-up of the unit 1 of nuclear power plant Mochovce. Test results of the stage of energetic start-up are summarized in the document, valuation of important systems and block devices as well as fulfilling the operation limits and conditions has been performed. On that base conclusions and recommendations for start-up the unit 2 and for commercial operation of the unit 1 are elaborated. The valuation has been elaborated by a scientific management for start-up nuclear power plant Mochovce of nuclear safety of nuclear power facilities. Scientific management for start-up of nuclear power plant Mochovce performed continuous valuation of individual power levels after ending of each individual level and it gave its valuation to energy power level with recommendations and conditions for further start-up process and operation. Scientific management finished its activity at the unit 1 of nuclear power plant Mochovce according to a statute of scientific management for start-up after successful completion of conclusive block run. Scientific management group was founded in February 1998 at nuclear power plant Mochovce. Its members are experts from Slovak, Czech, Russian and French organizations which are participating in power plant completion. Members are listed in a supplement No. 2

Neutron flux monitoring with pre-startup channels in FBTR [Paper No.:E6

International Nuclear Information System (INIS)

Nagaraj, C.P.; Ramakrishnan, R.; Subha Rao, R.; Pillai, C.P.; Muralikrishan, G.; Raghavan, K.

1993-01-01

The pre-start up instrumentation system using boron lined proportional counters has been well designed and the counters have been rigorously tested. This system in conjunction with the regular start-up channels (with more than 3 decades overlap) covers the start up measurement range adequately and provides necessary indications, interlocks and trips on low count rate, high count rate and doubling time to ensure safety. The pre-startup channels have been operational. The reactor trip on LOG NO due to count rate on start-up channels less than 3 cps is automatically inhibited with the higher count rate obtained on the pre-startup channels. With this and log CRM readings from PSU well on scale has facilitated smooth and safe reactor start ups even with low shutdown count rates. (author). 5 figs

Calculations of the startup experiments at the Poolside Facility

Energy Technology Data Exchange (ETDEWEB)

Williams, M.L.; Maerker, R.E.

1982-01-01

Discrete ordinate calculations are made and the results compared with measurements performed in the startup experiment at the Poolside Facility. Because of the physical size of the simulated surveillance capsule used in this experiment, the analytic procedure is more complicated than one adopted in earlier calculations of the PCA-PVF and PSF. The comparisons indicate the pressure vessel fluences in the long-term irradiation experiments still presently going on at the PSF, and which are geometrically identical to the startup experiment, can only be predicted to within about 20%.

Calculations of the startup experiments at the Poolside Facility

International Nuclear Information System (INIS)

Williams, M.L.; Maerker, R.E.

1982-01-01

Discrete ordinate calculations are made and the results compared with measurements performed in the startup experiment at the Poolside Facility. Because of the physical size of the simulated surveillance capsule used in this experiment, the analytic procedure is more complicated than one adopted in earlier calculations of the PCA-PVF and PSF. The comparisons indicate the pressure vessel fluences in the long-term irradiation experiments still presently going on at the PSF, and which are geometrically identical to the startup experiment, can only be predicted to within about 20%

A Studio Based Approach to Enhancing Decision Making in Sme Start-Up

NARCIS (Netherlands)

Sol, H G; Ejiri, A.H.; Nabukenya, J.

2011-01-01

The start-up phase plays an important role in the success and survival of many enterprises, which greatly depends on adequate and timely services for decision making. However, deciding to startup a mining Small and Medium Enterprise (SME) is a challenging task for many entrepreneurs in Uganda.

The design of control algorithm for automatic start-up model of HWRR

International Nuclear Information System (INIS)

Guo Wenqi

1990-01-01

The design of control algorithm for automatic start-up model of HWRR (Heavy Water Research Reactor), the calculation of μ value and the application of digital compensator are described. Finally The flow diagram of the automatic start-up and digital compensator program for HWRR are given

Epigenetic Tracking, a Method to Generate Arbitrary Shapes By Using Evolutionary-Developmental Techniques

OpenAIRE

Fontana, Alessandro

2008-01-01

This paper describes an Artificial Embryology method (called ``Epigenetic Tracking'') to generate predefined arbitrarily shaped 2-dimensional arrays of cells by means of evolutionary techniques. It is based on a model of development, whose key features are: i) the distinction bewteen ``normal'' and ``driver'' cells, being the latter able to receive guidance from the genome, ii) the implementation of the proliferation/apoptosis events in such a way that many cells are created/deleted at once, ...

Strategic planning model for Startups: A case study of Iranian packaging industry

Directory of Open Access Journals (Sweden)

Mohammad Mahdavi Mazdeh

2011-04-01

Full Text Available In today’s turbulent and competitive world, strategic planning plays an important role for the success of firms. Despite the fact that there are literally numerous models proposed for different companies in various states and structures, the possibility of using strategic planning for startups has never been seriously considered. In this paper, we present a survey by asking experts to find out whether strategic planning is suitable for startups. We also propose a model for strategic planning in startups based on the strategic planning models for small businesses and entrepreneurship concepts. The model is similar to other models and what differentiates this models form other approaches is the methodology used for internal and external analysis and the parameters taken into consideration. The proposed model is examined on an Iranian food packaging industry for validation. The preliminary results indicate that the success of startups depends on two sets of parameters: “entrepreneurial opportunities” and “competitive advantages and entrepreneurial characteristics”.

The Influence of Innovation and Entrepreneurial Self-Efficacy to Digital Startup Success

Directory of Open Access Journals (Sweden)

Agnes Dessyana

2017-08-01

Full Text Available Establishing and developing a startup business is not easy. Startup success depend on various aspects, such as financial,business model, and learning organizations. Personalities factor of founders have a contribution in business development, especially entrepreneurial self-efficacy (ESE and innovation. But, in Indonesia, there is still no psychological study who see the contribution of those factors on business success in digital startup. This study aimed to understand how both factors influence startup digital. The sample is 64 founders. The research instrument is ESE, KAI, and Business Success questionnaire (Kirton in Riyanti, 2003; Chen et al, 1998; Kaplan & Norton, 2006. Multiple-regression analyses reveal ESE and innovation contributes 20.8% to business success. ESE regression coefficient is 0.200 (P 0.05. This means, ESE has significant positive effect, while innovation has a positive relationship but insignificant. Interventions in the form of booklets that inform how to increase ESE. The booklet is already conducted trials on five founders.

Comparisons of Particle Tracking Techniques and Galerkin Finite Element Methods in Flow Simulations on Watershed Scales

Science.gov (United States)

Shih, D.; Yeh, G.

2009-12-01

This paper applies two numerical approximations, the particle tracking technique and Galerkin finite element method, to solve the diffusive wave equation in both one-dimensional and two-dimensional flow simulations. The finite element method is one of most commonly approaches in numerical problems. It can obtain accurate solutions, but calculation times may be rather extensive. The particle tracking technique, using either single-velocity or average-velocity tracks to efficiently perform advective transport, could use larger time-step sizes than the finite element method to significantly save computational time. Comparisons of the alternative approximations are examined in this poster. We adapt the model WASH123D to examine the work. WASH123D is an integrated multimedia, multi-processes, physics-based computational model suitable for various spatial-temporal scales, was first developed by Yeh et al., at 1998. The model has evolved in design capability and flexibility, and has been used for model calibrations and validations over the course of many years. In order to deliver a locally hydrological model in Taiwan, the Taiwan Typhoon and Flood Research Institute (TTFRI) is working with Prof. Yeh to develop next version of WASH123D. So, the work of our preliminary cooperationx is also sketched in this poster.

Reactor power system deployment and startup

International Nuclear Information System (INIS)

Wetch, J.R.; Nelin, C.J.; Britt, E.J.; Klein, G.; Rasor Associates, Inc., Sunnyvale, CA; California Institute of Technology, Pasadena)

1985-01-01

This paper addresses issues that should receive further examination in the near-term as concept selection for development of a U.S. space reactor power system is approached. The issues include: the economics, practicality and system reliability associated with transfer of nuclear spacecraft from low earth shuttle orbits to operational orbits, via chemical propulsion versus nuclear electric propulsion; possible astronaut supervised reactor and nuclear electric propulsion startup in low altitude Shuttle orbit; potential deployment methods for nuclear powered spacecraft from Shuttle; the general public safety of low altitude startup and nuclear safe and disposal orbits; the question of preferred reactor power level; and the question of frozen versus molten alkali metal coolant during launch and deployment. These issues must be considered now because they impact the SP-100 concept selection, power level selection, weight and size limits, use of deployable radiators, reliability requirements, and economics, as well as the degree of need for and the urgency of developing space reactor power systems. 5 references

Terahertz performance of quasioptical front-ends with a hotelectron bolometer

International Nuclear Information System (INIS)

Semenov, A; Richter, H; Guenther, B; Huebers, H-W; Karamarkovic, J

2006-01-01

We present terahertz performance of quasioptical front-ends consisting of a hotelectron bolometer imbedded in a planar feed antenna and integrated with an immersion lens. The impedance and radiation pattern of the log-spiral and double-slot planar feeds are evaluated using the method of moments; the collimating action of the lens is modelled using the physical optics. The total efficiency of the front-ends is computed taking into account frequency dependent impedance of the bolometer. Measured performance of the front-ends qualifies the simulation technique as a reliable tool for the design of terahertz receivers

A single center analysis of factors influencing study start-up timeline in clinical trials.

Science.gov (United States)

Krafcik, Brianna M; Doros, Gheorghe; Malikova, Marina A

2017-11-01

Efficient start-up phase in clinical trials is crucial to execution. The goal was to determine factors contributing to delays. The start-up milestones were assessed for 38 studies and analyzed. Total start-up time was shorter for following studies: device trials, no outsourcing, fewer ancillary services used and in interventional versus observational designs. The use of a centralized Institutional Review Board (IRB) versus a local IRB reduced time to approval. Studies that never enrolled took longer on average to finalize their budget/contract, and obtain IRB than ones that did enroll. Different features of clinical trials can affect timeline of start-up process. An understanding of the impact of each feature allows for optimization.

Start-up assist by magnetized plasma flow injection in TPE-RX reversed-field pinch

Energy Technology Data Exchange (ETDEWEB)

Asai, T. [College of Science and Technology, Nihon University, 1-8 Kanda-Surugadai, Chiyoda-ku, Tokyo 101-8308 (Japan)]. E-mail: asai@phys.cst.nihon-u.ac.jp; Nagata, M. [Graduate School of Engineering, University of Hyogo, Himeji (Japan); Koguchi, H. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Hirano, Y. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Sakakita, H. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Yambe, K. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Kiyama, S. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan)

2006-11-15

A reversed-field pinch (RFP) start-up assisted by a magnetized plasma flow injection was demonstrated for the first time on a TPE-RX machine. This sequence of experiments aimed to establish a new method of ionization, gas-fill and helicity injection in the start-up phase of an RFP. In this start-up method, magnetized and well-ionized plasma is formed by a magnetized coaxial plasma gun and injected into the torus chamber as an initial pre-ionized plasma for RFP formation. In the initial experiments, attenuated density pump-out and comparatively slow decay of the toroidal flux and plasma current were observed as evidence of its being an effective start-up method.

Environmental mitigation for SCC initiation of BWR core internals by hydrogen injection during start-up

International Nuclear Information System (INIS)

Dozaki, K.; Abe, A.; Nagata, N.; Takiguchi, H.

2004-01-01

Hydrogen injection into the reactor water has been applied to many BWR power stations. Since hydrogen injected accelerates recombination of oxidant generated by water radiolysis, oxidant concentration, such as dissolved oxygen concentration in reactor water can be reduced. As the result of the reduction of oxidant concentration, Electrochemical Corrosion Potential (ECP) at the surface of structural material can be lowered. Lowered ECP moderates Stress Corrosion Cracking (SCC) sensitivity of structural materials, such as stainless steels. As usual, hydrogen injection system begins to work after the plant start-up is finished, when the condition of normal operation is established. Accordingly, Hydrogen Water Chemistry (HWC) does not cover all the period of plant operation. As far as SCC crack growth is considered, loss of HWC during plant start-up does not result in significant crack growth, because of duration of plant start-up is much shorter than that of plant normal operation, when HWC condition is being satisfied. However, the reactor water environment and load conditions during a plant start-up may contribute to the initiation of SCC. It is estimated that the core internals are subjected to the strain rate that may cause susceptibility to SCC initiation during start-up. Dissolved oxygen (DO) and hydrogen peroxide (H 2 O 2 ) has a peak, and ECP is in high levels during start-up. Therefore it is beneficial to perform hydrogen injection during start-up as well in order to suppress SCC initiation. We call it HWC During Start-up (HDS) here. (orig.)

GROWTH HACKING PRACTICES IN A START-UP: A CASE STUDY ON THECON.RO

Directory of Open Access Journals (Sweden)

Marius GERU

2014-06-01

Full Text Available Despite the increasing awareness of content marketing tools in the academic community, the benefits of growth hacking were highlighted especially in blog posts and several e-books. This paper examines the particular features of growth hacking techniques, which differentiates it from traditional marketing. Specifically, a content analysis was conducted to identify the experts’ opinions regarding the effective use of growth hacking techniques, to detect the specific skills that a growth hacker must gain and to compare the tools related to this concept from both inbound and outbound marketing perspective. On the other hand, we outlined the need for development of start-ups, without spending huge amounts of money in marketing. Using a case study methodology, we examined the motivations of adopting growth hacking techniques by an Internet pure player - Thecon. Results show that the effective mix of growth hacking techniques applied by this company tends to forward more online content than its competitors.

A Wireless Fatigue Monitoring System Utilizing a Bio-Inspired Tree Ring Data Tracking Technique

Directory of Open Access Journals (Sweden)

Shi Bai

2014-03-01

Full Text Available Fatigue, a hot scientific research topic for centuries, can trigger sudden failure of critical structures such as aircraft and railway systems, resulting in enormous casualties as well as economic losses. The fatigue life of certain structures is intrinsically random and few monitoring techniques are capable of tracking the full life-cycle fatigue damage. In this paper, a novel in-situ wireless real-time fatigue monitoring system using a bio-inspired tree ring data tracking technique is proposed. The general framework, methodology, and verification of this intelligent system are discussed in details. The rain-flow counting (RFC method is adopted as the core algorithm which quantifies fatigue damages, and Digital Signal Processing (DSP is introduced as the core module for data collection and analysis. Laboratory test results based on strain gauges and polyvinylidene fluoride (PVDF sensors have shown that the developed intelligent system can provide a reliable quick feedback and early warning of fatigue failure. With the merits of low cost, high accuracy and great reliability, the developed wireless fatigue sensing system can be further applied to mechanical engineering, civil infrastructures, transportation systems, aerospace engineering, etc.

A wireless fatigue monitoring system utilizing a bio-inspired tree ring data tracking technique.

Science.gov (United States)

Bai, Shi; Li, Xuan; Xie, Zhaohui; Zhou, Zhi; Ou, Jinping

2014-03-05

Fatigue, a hot scientific research topic for centuries, can trigger sudden failure of critical structures such as aircraft and railway systems, resulting in enormous casualties as well as economic losses. The fatigue life of certain structures is intrinsically random and few monitoring techniques are capable of tracking the full life-cycle fatigue damage. In this paper, a novel in-situ wireless real-time fatigue monitoring system using a bio-inspired tree ring data tracking technique is proposed. The general framework, methodology, and verification of this intelligent system are discussed in details. The rain-flow counting (RFC) method is adopted as the core algorithm which quantifies fatigue damages, and Digital Signal Processing (DSP) is introduced as the core module for data collection and analysis. Laboratory test results based on strain gauges and polyvinylidene fluoride (PVDF) sensors have shown that the developed intelligent system can provide a reliable quick feedback and early warning of fatigue failure. With the merits of low cost, high accuracy and great reliability, the developed wireless fatigue sensing system can be further applied to mechanical engineering, civil infrastructures, transportation systems, aerospace engineering, etc.

Development of the fission fragment track registration technique for the determination of the uranium contamination

International Nuclear Information System (INIS)

Tanaka, E.M.

1979-01-01

The Fission Fragment Track Registration Technique is developed to measure the uranium concentration about microgram of uranium per litre of liquid samples. The drying method of drops on the detector (Makrofol KG) and a special sampling procedure to avoid the cumbersome high density of tracks formation at the edge of the deposition surface as a 'ring' is adopted. The samples are irradiated by neutrons produced by the IEA-R1 Reactor (thermal neutron flux about 10 12 neutrons/cm 2 .s) inducing the uranium fission. The tracks registered by the fission fragments in the detector are chemically enlarged and counted by an automatic couting system. By this method the uranium concentrations ranging from 0,9 to 7,6 microgram of uranium per litre, can be determined with precisions between 2,7% the greater and 23% to the lower concentration. The uranium concentration measurements in human hair and urine are made showing that this method is very useful to control and detect eventual uranium contamination [pt

Replacement of Cross-Site Transfer System Startup Plan

International Nuclear Information System (INIS)

Gerken, M.D.

1996-01-01

This Startup Plan provides a discussion of organizational responsibilities, work planning, quality assurance (QA), personnel qualifications, and testing requirements for the Cross-Site Transfer System

Intentions to Apply as Internship Students on Digital Start-Up Companies in Jakarta

Directory of Open Access Journals (Sweden)

Liza Agustina Maureen Nelloh

2017-11-01

Full Text Available Human capital plays an important role in explaining organizational performance and survival, not only for well-established firms but also for digital startup companies. However no previous human resource literature, especially on employers’ brand, investigates the internship program in the startup digital firms. Our pre-test shows that students are less attracted to apply to startup digital companies. Consequently, this study aims to test students’ intention to be on an internship in startup digital companies with its several antecedents (organizational attractiveness, job meaning, organizational attributes, and institutional image. My purposive sampling generates 101 business and management students in Jakarta as my sample. I run Partial Least Square (PLS to test my hypothesis. The results indicate that organizational attributes do not affect intention to be on an internship and other hypothesis tests exhibit positive results. Further, the findings also show that organizational attributes do not exhibit mediating effect. Overall, the results suggest that digital startup companies cooperate and collaborate with universities, especially business and management departments in research and student projects in order to attract the best students to be on internship on these companies that eventually will improve their performance. Abstrak Sumber Daya Manusia memegang peran penting dalam ketahanan dan peningkatan kinerja perusahaan baik berskala besar ataupun berskala startup digital. Akan tetapi, penelitian sebelumnya mengenai sumber daya manusia khususnya merek perekrut yang menguji secara khusus pada program magang yang banyak dilakukan oleh jurusan bisnis dan manajemen atau sejenisnya masih jarang dilakukan. Kemudian, hasil prates menunjukkan rendahnya ketertarikan dan keinginan mahasiswa untuk melamar di perusahaan startup digital. Oleh karena itu, penelitian ini bertujuan untuk menguji intensi melamar calon mahasiswa magang di perusahaan

Light duty utility arm startup plan

International Nuclear Information System (INIS)

Barnes, G.A.

1998-01-01

This plan details the methods and procedures necessary to ensure a safe transition in the operation of the Light Duty Utility Arm (LDUA) System. The steps identified here outline the work scope and identify responsibilities to complete startup, and turnover of the LDUA to Characterization Project Operations (CPO)

Quality Management techniques embedded in Agile Project Development

Directory of Open Access Journals (Sweden)

Dovleac Raluca

2017-01-01

Full Text Available It used to be hard to make your dream come true and start a business but now, thanks to the dotcom boom and the rapid development of emerging technologies everybody has the chance to become the next Steve Jobs. Quality management tools and creativity techniques gave birth to the startup trend that transforms a brilliant idea into an innovative product. A common practice amongst startups is Agile development. In this paper, after analyzing the Agile approach and the tools used to ensure quality for every stage of a product’s development life cycle and the results of using the Agile approach looking out for advantages and short comings as well, we proposed a PDCA inspired tool which embeds both quality and creativity techniques to help developers ensure quality for each stage of a product’s life cycle as well as help them better organize their activities to reach the desired goals. We validated this approach by implementing it to the case of the Vitraly startup.

Start-up First Term Sheet: Stumbling Blocks to Avoid

Directory of Open Access Journals (Sweden)

Amalyan Nataly D.

2018-01-01

Full Text Available Start-up relationships with business angel and/or venture capital are similar to a marriage – but with a divorce in mind. The latter necessitates a proper prenuptial agreement signing at the very beginning of the relations. In case of business angel and/or venture capital we are speaking about Term sheet, determining pricing, powers and duties of the board, as well as information, participation and protective rights for the partners. Standard Term sheet consists of three buckets of provisions, defining: (i terms impacting start-up valuation and economic division of profits and proceeds upon a liquidity event, (ii terms impacting control over decision making and (iii investor protection terms. This article focuses on financial and economic aspects of funding agreement, exposing some tricky parts of the Term sheet, threatening to transform potential win-win deals into rupture of relations, crash of the company or even legal battles. The results of the analysis are used to substantiate growing in popular appeal thesis that raising too much money can be detrimental for a startup.

Creating a business toolbox for a start-up : a case study of SnapSwap International

OpenAIRE

Kovshikov, Iaroslav

2017-01-01

This thesis was implemented at SnapSwap International in spring and summer 2017. The case company is a fin-tech start-up established in 2015 and located in Luxembourg. The company aims to develop a new payment solution (money messenger) for the European market. The purpose of the thesis is to observe commonly used business techniques (SWOT, Business Model Canvas (BMC), Persona, and Empathy Map) and analyze current business activities of the company employing these tools. The theoretic...

The impact of FinTech start-ups on incumbent retail banks' share prices

OpenAIRE

Li, Yinqiao; Spigt, Renée; Swinkels, Laurens

2017-01-01

Background: This study aims to clarify the role of FinTech digital banking start-ups in the financial industry. We examine the impact of the funding of such start-ups on the stock returns of 47 incumbent US retail banks for 2010 to 2016. Methods: To capture the importance of FinTech start-ups, we use data on both the dollar-volume of funding and number of deals. We relate these to the stock returns with panel data regression methods. Results: Our results indicate a positive relationship exist...

Methods for enhancing mapping of thermal fronts in oil recovery

Science.gov (United States)

Lee, D.O.; Montoya, P.C.; Wayland, J.R. Jr.

1984-03-30

A method for enhancing the resistivity contrasts of a thermal front in an oil recovery production field as measured by the controlled source audio frequency magnetotelluric (CSAMT) technique is disclosed. This method includes the steps of: (1) preparing a CSAMT-determined topological resistivity map of the production field; (2) introducing a solution of a dopant material into the production field at a concentration effective to alter the resistivity associated with the thermal front; said dopant material having a high cation exchange capacity which might be selected from the group consisting of montmorillonite, illite, and chlorite clays; said material being soluble in the conate water of the production field; (3) preparing a CSAMT-determined topological resistivity map of the production field while said dopant material is moving therethrough; and (4) mathematically comparing the maps from step (1) and step (3) to determine the location of the thermal front. This method is effective with the steam flood, fire flood and water flood techniques.

Model citizens. Outsourcing helps start-up Medicare HMO.

Science.gov (United States)

Slavic, B; Adami, S

1999-04-01

Health Plans of Pennsylvania (HPP), the managed care arm of Crozer-Keystone Health System, in Media, Pa. Selecting the information systems and building the infrastructure to support the start-up of a new Medicare HMO product. HPP chose to outsource the information systems needed to integrate all the components of managed care administration into a cost-effective and cohesive program. Because of its aggressive programming and start-up of the MedCarePlus product offering, HPP became the first plan in the country to submit Medicare claims data electronically for encounter reporting to the Health Care Financing Administration (HCFA). "Through an integrated team approach, an organization truly can benefit from the economies of scale gained through outsourcing."

Numerical resolution of a bi-temperature MHD model with a general Ohm's law: Roe solver - Front-tracking - Nonlinear transport equations with discontinuous coefficients. Simulation of a Plasma Opening Switch

International Nuclear Information System (INIS)

Brassier, Stephane

1998-01-01

The Magnetohydrodynamic (MHD) equations represent the coupling between fluid dynamics equations and Maxwell's equations. We consider here a new MHD model with two temperatures. A Roe scheme is first constructed in the one dimensional case, for a multi-species model and a general equation of state. The multidimensional case is treated thanks to the Powell approach. The notion of Roe-Powell matrix, generalization of the notion of Roe matrix for multidimensional MHD, allows us to develop an original scheme on a curvilinear grid. We focus on a second part on the modelling of a Plasma Opening Switch (POS). A front-tracking method is first set up, in order to correctly handle the deformation of the front between the vacuum and the plasma. Besides, by taking into account a general Ohm's law, we have to deal with the Hall effect, which leads to nonlinear transport equations with discontinuous coefficients. Several numerical schemes are proposed and tested on a variety of test cases. This work has allowed us to construct an industrial MHD code, intended to handle complex flows and in particular to correctly simulate the behaviour of the POS. (author) [fr

Novel Front-end Electronics for Time Projection Chamber Detectors

CERN Document Server

García García, Eduardo José

This work has been carried out in the European Organization for Nuclear Research (CERN) and it was supported by the European Union as part of the research and development towards the European detector the (EUDET) project, specifically for the International Linear Collider (ILC). In particle physics there are several different categories of particle detectors. The presented design is focused on a particular kind of tracking detector called Time Projection Chamber (TPC). The TPC provides a three dimensional image of electrically charged particles crossing a gaseous volume. The thesis includes a study of the requirements for future TPC detectors summarizing the parameters that the front-end readout electronics must fulfill. In addition, these requirements are compared with respect to the readouts used in existing TPC detectors. It is concluded that none of the existing front-end readout designs fulfill the stringent requirements. The main requirements for future TPC detectors are high integration, an increased n...

An explosive-emitter cathode produced using the heavy ion track technique

International Nuclear Information System (INIS)

Akap'ev, G.N.; Korenev, S.A.

1988-01-01

A cathode based on thin metallic foils with a homogeneous needle surface is described. The cathode was manufactured using the heavy ion track technique which permits the production of cathodes with an unlimited area and a needle density ranging from about 10 3 to 10 9 needles per cm 2 . An electron gun using this type of cathode has a current of 200-900 A and an energy of 100-300 keV. The cross section of the electron beam is fairly uniform. It is shown that needle emitters of similar shape and size play the principal role in forming a homogeneous cathode plasma

76 FR 50887 - Elections Regarding Start-Up Expenditures, Corporation Organizational Expenditures, and...

Science.gov (United States)

2011-08-17

... begins an active trade or business, an amount equal to the lesser of (1) the amount of the start-up... begins. All start-up expenditures that relate to the active trade or business are considered in... active trade or business to which the expenditures relate begins. The election either to amortize start...

Finite-time barriers to front propagation in two-dimensional fluid flows

Science.gov (United States)

Mahoney, John R.; Mitchell, Kevin A.

2015-08-01

Recent theoretical and experimental investigations have demonstrated the role of certain invariant manifolds, termed burning invariant manifolds (BIMs), as one-way dynamical barriers to reaction fronts propagating within a flowing fluid. These barriers form one-dimensional curves in a two-dimensional fluid flow. In prior studies, the fluid velocity field was required to be either time-independent or time-periodic. In the present study, we develop an approach to identify prominent one-way barriers based only on fluid velocity data over a finite time interval, which may have arbitrary time-dependence. We call such a barrier a burning Lagrangian coherent structure (bLCS) in analogy to Lagrangian coherent structures (LCSs) commonly used in passive advection. Our approach is based on the variational formulation of LCSs using curves of stationary "Lagrangian shear," introduced by Farazmand et al. [Physica D 278-279, 44 (2014)] in the context of passive advection. We numerically validate our technique by demonstrating that the bLCS closely tracks the BIM for a time-independent, double-vortex channel flow with an opposing "wind."

An efficient methodology for assessing attention to and effect of nutrition information displayed front-of-pack

NARCIS (Netherlands)

Bialkova, S.E.; Trijp, van H.C.M.

2011-01-01

A methodology for assessing attention to and effect of nutrition information displayed front-of-pack is presented. The methodology is based on an integration of the visual search paradigm, the choice paradigm and eye-tracking measures, and moves beyond reliance on self-report measures for attention

Trace uranium analysis in Indian coal samples using the fission track technique

International Nuclear Information System (INIS)

Jojo, P.J.; Rawat, A.; Kumar, Ashavani; Prasad, Rajendra

1993-01-01

The ever-growing demand for energy has resulted in the extensive use of fossil fuels, especially coal, for power generation. Coal and its by-products often contain significant amounts of radionuclides, including uranium, which is the ultimate source of the radioactive gas Radon-222. The present study gives the concentration of uranium in coal samples of different collieries in India, collected from various thermal power plants in the state of Uttar Pradesh. The estimates were made using the fission track technique. Latent damage tracks were not found to be uniformly distributed but showed sun bursts and clusters. Non-uniform distributions of trace elements are a very common phenomenon in rocks. The levels of uranium in the coal samples were found to vary from 2.0 to 4.9 ppm in uniform distributions and from 21.3 to 41.0 ppm in non-uniform distributions. Measurements were also made on fly ash samples where the average uranium concentration was found to be 8.4 and 49.3 ppm in uniform and non-uniform distributions, respectively. (author)

The value of business incubation services for early stage start-ups

DEFF Research Database (Denmark)

Jakobsen, Brian; Tanev, Stoyan; Jensen, Søren

2017-01-01

of the needs of early stage start-ups since they: i) do not have a well-articulated business model but work towards establishing one; ii) operate under conditions of significantly high risks and uncertainties; and iii) have not developed the minimum viable set of partners that would enable them to demonstrate...... in specific incubation programs. The findings should contribute to existing literature within the topic of business-incubation, as well as provide managers of both incubators and start-ups with actionable insights about the ways of maximizing the value of incubation services.......The paper focuses on conceptualizing the value of business incubation services for early stage start-ups that are typical of university-based entrepreneurial ecosystems. The challenge of such conceptualization consists in two main issues. The first issue is taking into account the specificity...

To Internationalize or Not to Internationalize? A Descriptive Study of a Brazilian Startup

Directory of Open Access Journals (Sweden)

Flavia Luciane Scherer

2018-03-01

Full Text Available This study examines the failed internationalization experience of a Brazilian high-tech startup. The research methodology of the study is descriptive and aims to explore whether this startup should re-internationalize, despite an unsuccessful first experience. Based on interviews with the founders, it was found that the initial internationalization took place in an incipient way, in the heat of the moment. The lack of success with the initial internationalization did not shake the directors of the startup, who aim to return to internationalization, now in a consolidated way and counting on the advice of an investor. Despite its bitter first experience, should the startup try again? Through an analysis of the lessons learned from the startup’s initial failure and insights from its consideration of a possible second attempt, this study contributes to the literature on competitiveness, internationalization, and international entrepreneurship.

Ophthalmic Start-Up Chief Executive Officers' Perceptions of Development Hurdles.

Science.gov (United States)

Stewart, William C; Nelson, Lindsay A; Kruft, Bonnie; Stewart, Jeanette A

2018-01-01

To identify current challenges facing ophthalmic pharmaceutical start-ups in developing new products. Surveys were distributed to the chief executive officer (CEO) or president of ophthalmic start-ups. The survey attracted 24 responses from 78 surveys distributed (31%). The CEOs stated that a lack of financial capital (n = 18, 75%), FDA regulations (n = 6, 25%), and failure to meet clinical endpoints (n = 6, 25%) were their greatest development hurdles. Risk aversion to medicines in early development (n = 18, 75%), mergers and acquisitions reducing corporate choice for licensing agreements (n = 7, 29%), the emergence of large pharmaceutical-based venture capital funding groups (n = 12, 50%), and the failure of many large pharmaceutical companies to develop their own medicines (n = 10, 42%) were noted as recent prominent trends affecting fundraising. The study suggests that development funding, regulatory burden, and meeting clinical endpoints are the greatest development challenges faced by ophthalmic start-up CEOs. © 2017 S. Karger AG, Basel.

Market Channels of Technology Startups that Internationalize Rapidly from Inception

Directory of Open Access Journals (Sweden)

Simar Yoos

2012-10-01

Full Text Available The study of technology startups that internationalize rapidly from inception has increased in recent years. However, little is known about their channels to market. This article addresses a gap in the "born global" literature by examining the channels used by six startups that internationalized rapidly from inception as well as the programs they used to support their channel partners and customers. The six startups examined combined the use of the Internet with: i a relationship with a multi-national, ii distributors, iii re-sellers, or iv a direct sales force. They also delivered programs to support partners and customers that focused on communications, alliance and network development, education, marketing and promotion, and financial incentives. This article informs entrepreneurs who need to design go-to-market channels to exploit global opportunities about decisions made by other entrepreneurs who launched born-global companies. Normative rules and practitioner-oriented approaches are needed to help entrepreneurs explain and apply the results presented in this article.

Strategies for the startup of methanogenic inverse fluidized-bed reactors using colonized particles.

Science.gov (United States)

Alvarado-Lassman, A; Sandoval-Ramos, A; Flores-Altamirano, M G; Vallejo-Cantú, N A; Méndez-Contreras, J M

2010-05-01

One of the inconveniences in the startup of methanogenic inverse fluidized-bed reactors (IFBRs) is the long period required for biofilm formation and stabilization of the system. Previous researchers have preferred to start up in batch mode to shorten stabilization times. Much less work has been done with continuous-mode startup for the IFBR configuration of reactors. In this study, we prepared two IFBRs with similar characteristics to compare startup times for batch- and continuous-operation modes. The reactors were inoculated with a small quantity of colonized particles and run for a period of 3 months, to establish the optimal startup strategy using synthetic media as a substrate (glucose as a source of carbon). After the startup stage, the continuous- and batch-mode reactors removed more than 80% of the chemical oxygen demand (COD) in 51 and 60 days of operation, respectively; however, at the end of the experiments, the continuous-mode reactor had more biomass attached to the support media than the batch-mode reactor. Both reactors developed fully covered support media, but only the continuous-mode reactor had methane yields close to the theoretical value that is typical of stable reactors. Then, a combined startup strategy was proposed, with industrial wastewater as the substrate, using a sequence of batch cycles followed by continuous operation, which allows stable operation at an organic loading rate of 20 g COD/L x d in 15 days. Using a fraction of colonized support as an inoculum presents advantages, with respect to previously reported strategies.

When does start-up innovation spur the gale of creative destruction?

OpenAIRE

Gans, Joshua S.; Hsu, David H.; Stern, Scott

2001-01-01

This paper is motivated by the substantial differences in start-up commercialization strategies observed across different high-technology sectors. Specifically, we evaluate the conditions under which start-up innovators earn their returns on innovation through product market competition with more established firms (such as in many areas of the electronics industry) as opposed to cooperation with these incumbents (either through licensing, strategic alliances or outright acquisition as observe...

Social Capital in Knowledge Intensive Start-Ups

DEFF Research Database (Denmark)

Neergaard, Helle; Madsen, Henning

This paper addresses social capital in biotechnology, medico and information communication start-ups using both quantitative and qualitative data. It shows that founding teams are primarily composed of 'trusted alters' and that networking patterns are highly influenced by the entrepreneur...

Dependence of alpha particle track diameter on the free volume holes size using positron annihilation lifetime technique

Energy Technology Data Exchange (ETDEWEB)

El-Gamal, S. [Physics Department, Faculty of Education, Ain Shams University, Roxy, 11711 Cairo (Egypt); Abdalla, Ayman M., E-mail: aymanabdalla62@hotmail.com [Physics Department, Faculty of Arts and Sciences, Najran University, Najran (Saudi Arabia); Centre for Advanced Materials and Nano-Engineering, Najran University, Najran 11001 (Saudi Arabia); Abdel-Hady, E.E. [Physics Department, Faculty of Science, Minia University, BO 61519, Minia (Egypt)

2015-09-15

The alpha particle track diameter dependence of the free volume holes size (V{sub f}) in DAM–ADC and CR-39 nuclear track detectors was investigated using positron annihilation lifetime technique. The effect of temperature on the alpha particle track diameter and free volume were also investigated in the T-range (RT-130 °C). The obtained results revealed that the values of ortho-positronium lifetime τ{sub 3} and V{sub f} increases while I{sub 3} slightly increases as T increases for the two detectors. The values of τ{sub 3}, V{sub f} and I{sub 3} are higher in CR-39 than DAM–ADC. The interpretation of obtained results is based on the fact that increasing T leads to significant enhancement of thermal expansion of the polymer matrix and consequently V{sub f} increases. The track diameter increases as T increases. This can be explained by the fact that the increase in T increases the crystal size and V{sub f} in the polymer. A relationship between V{sub f} and the alpha particle track diameter was obtained. Moreover results of detector irradiation, along with free volume evaluation are addressed and thoroughly discussed.

Determination of trace uranium in human hair by nuclear track detection technique

International Nuclear Information System (INIS)

Chung, Yong Sam; Moon, Jong Hwa; En, Zinaida; Cho, Seung Yeon; Kang, Sang Hoon; Lee, Jae Ki

2001-01-01

The aim of this study is to describe a usefulness of nuclear analytical technique in assessing and comparing the concentration levels through the analysis of uranium using human hair sample in the field of environment. A fission track detection technique was applied to determine the uranium concentration in human hair. Hair samples were collected from two groups of people - a) workers not dealing with uranium directly, and b) workers possibly contaminated with uranium. The concentration of 235 U for the first group varied from <1 to 39 ng/g and the second group can be estimated up to the level of μg/g. Radiographs of heavy-duty work samples contained high dense 'hot spots' along a single hair. After washing in acetone and distilled water, external contamination was not totally removed. Insoluble uranium compounds were not completely washed out. The (n, f)-radiography technique, having high sensitivity, and capable of getting information on uranium content at each point of a single hair, is an excellent tool for environmental monitoring

Improving startup performance with carbon mesh anodes in separator electrode assembly microbial fuel cells

KAUST Repository

Zhang, Fang; Xia, Xue; Luo, Yong; Sun, Dan; Call, Douglas F.; Logan, Bruce E.

2013-01-01

In a separator electrode assembly microbial fuel cell, oxygen crossover from the cathode inhibits current generation by exoelectrogenic bacteria, resulting in poor reactor startup and performance. To determine the best approach for improving startup

Effect of zero-valent iron and trivalent iron on UASB rapid start-up.

Science.gov (United States)

Wang, Jie; Fang, Hongyan; Jia, Hui; Yang, Guang; Gao, Fei; Liu, Wenbin

2018-01-01

In order to realize the rapid start-up of upflow anaerobic sludge blanket (UASB) reactor, the iron ion in different valence state was added to UASB. The results indicated that the start-up time of R3 (FeCl 3 ) was 48 h faster than that of R2 (zero-valent iron (ZVI)). It was because the FeCl 3 could rapidly promote granulation of sludge as a flocculant. However, ZVI released Fe 2+ through corrosion slowly, and then the Fe 2+ increased start-up speed by enhancing enzyme activity and enriching methanogens. In addition, the ZVI and FeCl 3 could promote hydrolysis acidification and strengthen the decomposition of long-chain fatty acids. The detection of iron ions showed that iron ions mainly existed in the sludge. Because the high concentration of Fe 2+ could inhibit anaerobic bacteria activity, excess Fe 3+ could be changed into iron hydroxide precipitation to hinder the mass transfer process of anaerobic bacteria under the alkaline condition. The FeCl 3 was suitable to be added at the initial stage of UASB start-up, and the ZVI was more fitted to be used in the middle stage of reactor start-up to improve the redox ability.

Numerical Investigation of Transient Flow in a Prototype Centrifugal Pump during Startup Period

Science.gov (United States)

Zhang, Yu-Liang; Zhu, Zu-Chao; Dou, Hua-Shu; Cui, Bao-Ling; Li, Yi; Zhou, Zhao-Zhong

2017-05-01

Transient performance of pumps during transient operating periods, such as startup and stopping, has drawn more and more attentions recently due to the growing engineering needs. During the startup period of a pump, the performance parameters such as the flow rate and head would vary significantly in a broad range. Therefore, it is very difficult to accurately specify the unsteady boundary conditions for a pump alone to solve the transient flow in the absence of experimental results. The closed-loop pipe system including a centrifugal pump is built to accomplish the self-coupling calculation. The three-dimensional unsteady incompressible viscous flow inside the passage of the pump during startup period is numerically simulated using the dynamic mesh method. Simulation results show that there are tiny fluctuations in the flow rate even under stable operating conditions and this can be attributed to influence of the rotor-stator interaction. At the very beginning of the startup, the rising speed of the flow rate is lower than that of the rotational speed. It is also found that it is not suitable to predict the transient performance of pumps using the calculation method of quasi-steady flow, especially at the earlier period of the startup.

Startup work on Inshas cyclotron

International Nuclear Information System (INIS)

Vorogushin, M.F.; Strokach, A.P.; Shikhov, V.Ya.; Galchuk, A.V.; Soliman, A.N.; El-Abyad, M.; Comsan, M.N.H.; Saleh, Z.A.; Azzam, A.N.

2001-01-01

Startup works on the MGC-20 variable energy cyclotron in the Inshas Nuclear Research Center (Egypt) are described. The cyclotron is intended for acceleration of hydrogen and helium ions in a wide energy range (for protons - from 5 to 20 MeV). Main units of the cyclotron and results of computer experimental acceleration of protons to 18 MeV are described. The prospects of furthers investigations are presented [ru

SuperJet International case study: a business network start-up in the aeronautics industry

Science.gov (United States)

Corallo, Angelo; de Maggio, Marco; Storelli, Davide

This chapter presents the SuperJet International case study, a start-up in the aeronautics industry characterized by a process-oriented approach and a complex and as yet evolving network of partnerships and collaborations. The chapter aims to describe the key points of the start-up process, highlighting common factors and differences compared to the TEKNE Methodology of Change, with particular reference to the second and third phase, namely, the design and deployment of new techno-organizational systems. The SuperJet International startup is presented as a case study where strategic and organizational aspects have been jointly conceived from a network-driven perspective. The chapter compares some of the guidelines of the TEKNE Methodology of Change with experiences and actual practices deriving from interviews with key players in SJI's start-up process.

Simulation on the start-up of MED seawater desalination system coupled with nuclear heating reactor

International Nuclear Information System (INIS)

Ge Zhihua; Du Xiaoze; Yang Lijun; Yang Yongping; Wu Shaorong

2008-01-01

The mathematical control model for dynamic start-up process of the VTE-MED seawater desalination system was established employing the previous developed non-linear differential equations for system design and performance analysis. The influences on the start-up process of the operating parameters, such as the initial feed brine flow rate and the top brine temperature were analyzed. The relationships among the feed brine flow rate, the gained output ratio (GOR) and the start-up time were also investigated, which can be evidence to determine the optimal initial feed brine flow rate. The results also indicate that the system can consume the total heat rating generated by the low temperature nuclear heating reactor (LT-NHR) even at the most initial start-up stage, implying the present desalination system has excellent coupling characteristics with the LT-NHR. With necessary experiments verifications, the start-up control model developed in this paper can be the theoretical base for the analysis of dynamic performances of the seawater desalination system

Watts Bar Unit 2 Startup Results with VERA

Energy Technology Data Exchange (ETDEWEB)

Godfrey, Andrew T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Collins, Benjamin S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gentry, Cole A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stimpson, Shane G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ritchie, John A. [Tennessee Valley Authority (TVA), Knoxville, TN (United States)

2017-03-01

CASL members TVA, Westinghouse, and Oak Ridge National Laboratory have successfully completed a detailed simulation of the initial startup of Watts Bar Nuclear Unit 2 (WBN2) using the advanced reactor simulation tools known as VERA. WBN2 is the first commercial power reactor to join the nation’s electrical grid in over two decades, and the modern core design and availability of data make it an excellent benchmark for CASL. Calculations were performed three months prior to the startup, and in the first blind application of VERA to a new reactor, predicted criticality and physics parameters very close to those later measured by TVA. Subsequent calculations with the latest version of VERA and using exact measurement conditions improved the results even further.

Front-end multiplexing—applied to SQUID multiplexing: Athena X-IFU and QUBIC experiments

Science.gov (United States)

Prele, D.

2015-08-01

As we have seen for digital camera market and a sensor resolution increasing to "megapixels", all the scientific and high-tech imagers (whatever the wave length - from radio to X-ray range) tends also to always increases the pixels number. So the constraints on front-end signals transmission increase too. An almost unavoidable solution to simplify integration of large arrays of pixels is front-end multiplexing. Moreover, "simple" and "efficient" techniques allow integration of read-out multiplexers in the focal plane itself. For instance, CCD (Charge Coupled Device) technology has boost number of pixels in digital camera. Indeed, this is exactly a planar technology which integrates both the sensors and a front-end multiplexed readout. In this context, front-end multiplexing techniques will be discussed for a better understanding of their advantages and their limits. Finally, the cases of astronomical instruments in the millimeter and in the X-ray ranges using SQUID (Superconducting QUantum Interference Device) will be described.

Front-end multiplexing—applied to SQUID multiplexing: Athena X-IFU and QUBIC experiments

International Nuclear Information System (INIS)

Prele, D.

2015-01-01

As we have seen for digital camera market and a sensor resolution increasing to 'megapixels', all the scientific and high-tech imagers (whatever the wave length - from radio to X-ray range) tends also to always increases the pixels number. So the constraints on front-end signals transmission increase too. An almost unavoidable solution to simplify integration of large arrays of pixels is front-end multiplexing. Moreover, 'simple' and 'efficient' techniques allow integration of read-out multiplexers in the focal plane itself. For instance, CCD (Charge Coupled Device) technology has boost number of pixels in digital camera. Indeed, this is exactly a planar technology which integrates both the sensors and a front-end multiplexed readout. In this context, front-end multiplexing techniques will be discussed for a better understanding of their advantages and their limits. Finally, the cases of astronomical instruments in the millimeter and in the X-ray ranges using SQUID (Superconducting QUantum Interference Device) will be described

Analysis of the IEA-R1 reactor start-up procedures - an application of the HazOp method

International Nuclear Information System (INIS)

Sauer, Maria Eugenia Lago Jacques

2000-01-01

An analysis of technological catastrophic events that took place in this century shows that human failure and vulnerability of risk management programs are the main causes for the occurrence of accidents. As an example, plants and complex systems where the interface man-machine is close, the frequency of failures tends to be higher. Thus, a comprehensive knowledge of how a specific process can be potentially hazardous is a sine qua non condition to the operators training, as well as to define and implement more efficient plans for loss prevention and risk management. A study of the IEA-R1 research reactor start-up procedures was carried out, based upon the methodology Hazard and Operability Study (HazOp). The analytical and qualitative multidisciplinary HazOp approach provided means to a comprehensive review of the reactor start-up procedures, contributing to improve the understanding of the potential hazards associated to deviations on performing this routine. The present work includes a historical summary and a detailed description of the HazOp technique, as well as case studies in the process industries and the use of expert systems in the application of the method. An analysis of 53 activities of the IEA-R1 reactor start-up procedures was made, resulting in 25 recommendations of changes covering aspects of the project, operation and safety of the reactor. Eleven recommendations have been implemented. (author)

On the breakdown modes and parameter space of Ohmic Tokamak startup

Science.gov (United States)

Peng, Yanli; Jiang, Wei; Zhang, Ya; Hu, Xiwei; Zhuang, Ge; Innocenti, Maria; Lapenta, Giovanni

2017-10-01

Tokamak plasma has to be hot. The process of turning the initial dilute neutral hydrogen gas at room temperature into fully ionized plasma is called tokamak startup. Even with over 40 years of research, the parameter ranges for the successful startup still aren't determined by numerical simulations but by trial and errors. However, in recent years it has drawn much attention due to one of the challenges faced by ITER: the maximum electric field for startup can't exceed 0.3 V/m, which makes the parameter range for successful startup narrower. Besides, this physical mechanism is far from being understood either theoretically or numerically. In this work, we have simulated the plasma breakdown phase driven by pure Ohmic heating using a particle-in-cell/Monte Carlo code, with the aim of giving a predictive parameter range for most tokamaks, even for ITER. We have found three situations during the discharge, as a function of the initial parameters: no breakdown, breakdown and runaway. Moreover, breakdown delay and volt-second consumption under different initial conditions are evaluated. In addition, we have simulated breakdown on ITER and confirmed that when the electric field is 0.3 V/m, the optimal pre-filling pressure is 0.001 Pa, which is in good agreement with ITER's design.

40 CFR 60.1710 - What happens to the emission limits during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... during periods of startup, shutdown, and malfunction? 60.1710 Section 60.1710 Protection of Environment... during periods of startup, shutdown, and malfunction? (a) The emission limits of this subpart apply at all times except during periods of municipal waste combustion unit startup, shutdown, or malfunction...

40 CFR 60.1205 - What happens to the operating requirements during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... requirements during periods of startup, shutdown, and malfunction? 60.1205 Section 60.1205 Protection of... requirements during periods of startup, shutdown, and malfunction? (a) The operating requirements of this subpart apply at all times except during periods of municipal waste combustion unit startup, shutdown, or...

Reconstructing events, from electronic signals to tracks

CERN Multimedia

CERN. Geneva

2015-01-01

Reconstructing tracks in the events taken by LHC experiments is one of the most challenging and computationally expensive software tasks to be carried out in the data processing chain. A typical LHC event is composed of multiple p-p interactions, each leaving signals from many charged particles in the detector and jus building up an environment of unprecedented complexity. In the lecture I will give an overview of event reconstruction in a typical High Energy Physics experiment. After an introduction to particle tracking detectors I will discuss the concepts and techniques required to master the tracking challenge at the LHC. I will explain how track propagation in a realistic detector works, present different techniques for track fitting and track finding. At the end we will see how all of those techniques play together in the ATLAS track reconstruction application.

Comparative Study of Maximum Power Point Tracking Techniques for Photovoltaic Systems

Directory of Open Access Journals (Sweden)

Fernando Lessa Tofoli

2015-01-01

Full Text Available The generation of electricity from photovoltaic (PV arrays has been increasingly considered as a prominent alternative to fossil fuels. However, the conversion efficiency is typically low and the initial cost is still appreciable. A required feature of a PV system is the ability to track the maximum power point (MPP of the PV array. Besides, MPP tracking (MPPT is desirable in both grid-connected and stand-alone photovoltaic systems because the solar irradiance and temperature change throughout the day, as well as along seasons and geographical conditions, also leading to the modification of the I×V (current versus voltage and P×V (power versus voltage curves of the PV module. MPPT is also justified by the relatively high cost of the energy generated by PV systems if compared with other sources. Since there are various MPPT approaches available in the literature, this work presents a comparative study among four popular techniques, which are the fixed duty cycle method, constant voltage (CV, perturb and observe (P&O, and incremental conductance (IC. It considers different operational climatic conditions (i.e., irradiance and temperature, since the MPP is nonlinear with the environment status. PSIM software is used to validate the assumptions, while relevant results are discussed in detail.

TRAX - Real-World Tracking of Moving Objects

DEFF Research Database (Denmark)

Jensen, Christian Søndergaard; Pakalnis, Stardas

2007-01-01

accuracy. This paper presents the TRAX tracking system that supports several techniques capable of tracking the current positions of moving objects with guaranteed accuracies at low update and communication costs in real-world settings. The techniques are readily relevant for practical applications......, but they also have implications for continued research. The tracking techniques offer a realistic setting for existing query processing techniques that assume that it is possible to always know the exact positions of moving objects. The techniques enable studies of trade-offs between querying and update...

Development of pre-startup equipment for light water reactors

International Nuclear Information System (INIS)

Ram, Rajit; Borkar, S.P.; Dixit, M.Y.; Das, Debashis; Patil, R.K.

2010-01-01

Light water reactor (LWR) core typically has high excess reactivity as compared to Pressurized Heavy Water Reactor (PHWR). Unlike PHWR, where online refueling is done, LWR is operated for a long period to achieve maximum fuel burn-up before refueling. Since the reactivity is always reducing with burn-up of the core, the positions of control rods at criticality are always changing in a single direction, i.e. away from the core. Therefore it is possible to start the LWR even if the nuclear instrumentation is not online, provided the criticality position of control rods is known for previous operation. However, for the very first startup, the criticality position of control rods is required to be determined. A special nuclear instrumentation system, called Pre-startup equipment (PSE) is developed using two numbers of in-core detectors along with the processing electronics. The PSE enables operators to determine the criticality position of control rods for the first startup at zero power. The same equipment can also be used during loading of fuel assemblies. This paper discusses the features and architecture of PSE, its individual circuit blocks and specifications. (author)

Time program using in automatization of steam turbines start-up

International Nuclear Information System (INIS)

Lejzerovich, A.Sh.; Melamed, A.D.

Examples and arguments for developing time programs of changing basic parameters of automated start-up of TPP and NPP high-power steam turbines are considered. Basic parameters subject to controlled changing at automatization of turbine start-up are rotation frequency, loading and temperature of steam supplied to the turbine. Principle facility schemes of program regulation of steam temperature at the start-up are presented. The facility scheme of loading the NPP wet steam turbine is given. The principles of developing time programs, of changing basic parameters of automated start-up enable realizing transient processes close to theoretically optimum processes at arbitrary prestart-up state of the turbine by means of rather simple autatic facilities. In particular, for automated temperature increase of steam supplied to the turbine of TES power units and AES turbine loading, it is advisable to use programs in the form of linear dependence of velocity of changing the controlled parameter on the given value, the initial level, from which the parameter increase with a regulated velocity is realized, is given in the form of analogue dependence on the turbine prestart-up state. The programs described and the schemes of their realization have been approved at the automatization of 300 MW power unit starts up with the K-300-240 turbine and K-220-44 turbine as well as used when creating control system for turbines of 500 MW and higher for designed TPP and NPP power units

Start-up of spherical tokamak without a center solenoid

International Nuclear Information System (INIS)

Maekawa, Takashi; Nagata, Masayoshi

2012-01-01

For low-aspect tokamak reactors, spherical tokamak reactors, ST-type FESF/CTFs, it is essential to remove or minimize a central solenoid (CS). Even with the minimized CS, non-inductive start up of the plasma current is required. Rapid increase in the spontaneous plasma current at the final stage of current start-up drives ignition. At the initial stage, formation of plasma and magnetic surfaces are required. As non-inductive plasma start-up scenarios, ECH/ECCD, LHCD, HHFW, DC HELICITY injection, plasma merging and NBI have been studied. In the present article, the present status and future prospect of experimental and theoretical works on these subjects. (author)

Program of RA reactor start-up to nominal power

International Nuclear Information System (INIS)

1959-01-01

The zero start-up program is followed by the program of RA reactor start-up to nominal power. This program is described in detail and includes the following measurements: radiation characteristics at the exit of the channels; gamma and fast neutron dose distribution in the reactor; influence of absorbers on the reactivity; temperature effect; absolute flux and calibration of ionization chambers; xenon effect; thermal and hydraulics; dosimetry around the reactor; neutron flux in the reactor core and in the reactor hall; heavy water level; thermal characteristics after shutdown. A list of measuring devices and instrumentation is included with the detailed action plan and list of responsible staff members

USA/FBR program status FFTF operations startup experience

International Nuclear Information System (INIS)

Moffitt, W.C.; Izatt, R.D.

1981-06-01

This paper gives highlights of the major Operations evaluations and operational results of the startup acceptance testing program and initiation of normal operating cycles for experiment irradiation in the FFTF. 33 figures

Startup, Shutdown, & Malfunction (SSM) Emissions at Industrial Facilities

Science.gov (United States)

EPA issued a final action to ensure states have plans in place that are fully consistent with the Clean Air Act and recent court decisions concerning startup, shutdown and malfunction (SSM) operations.

40 CFR 62.15165 - What happens to the emission limits during periods of startup, shutdown, and malfunction?

Science.gov (United States)

2010-07-01

... during periods of startup, shutdown, and malfunction? 62.15165 Section 62.15165 Protection of Environment... emission limits during periods of startup, shutdown, and malfunction? (a) The emission limits of this subpart apply at all times except during periods of municipal waste combustion unit startup, shutdown, or...

Kinematic, kinetic and EMG analysis of four front crawl flip turn techniques.

Science.gov (United States)

Pereira, Suzana Matheus; Ruschel, Caroline; Hubert, Marcel; Machado, Leandro; Roesler, Helio; Fernandes, Ricardo Jorge; Vilas-Boas, João Paulo

2015-01-01

This study aimed to analyse the kinematic, kinetic and electromyographic characteristics of four front crawl flip turn technique variants. The variants distinguished from each other by differences in body position (i.e., dorsal, lateral, ventral) during rolling, wall support, pushing and gliding phases. Seventeen highly trained swimmers (17.9 ± 3.2 years old) participated in interventional sessions and performed three trials of each variant, being monitored with a 3-D video system, a force platform and an electromyography (EMG) system. Studied variables: rolling time and distance, wall support time, push-off time, peak force and horizontal impulse at wall support and push-off, centre of mass horizontal velocity at the end of the push-off, gliding time, centre of mass depth, distance, average and final velocity during gliding, total turn time and electrical activity of Gastrocnemius Medialis, Tibialis Anterior, Biceps Femoris and Vastus Lateralis muscles. Depending on the variant, total turn time ranged from 2.37 ± 0.32 to 2.43 ± 0.33 s, push-off force from 1.86 ± 0.33 to 1.92 ± 0.26 BW and centre of mass velocity during gliding from 1.78 ± 0.21 to 1.94 ± 0.22 m · s(-1). The variants were not distinguishable in terms of kinematical, kinetic and EMG parameters during the rolling, wall support, pushing and gliding phases.

SP-100 initial startup and restart control strategy

International Nuclear Information System (INIS)

Halfen, F.J.; Wong, K.K.; Switick, D.M.; Shukla, J.N.

1992-01-01

This paper reports that recent Generic Flight System (GFS) updates have necessitated revisions in the initial startup and restart control strategies. The design changes that have had the most impact on the control strategies are the addition of the Auxiliary Cooling and Thaw (ACT) system for preheating the lithium filled components, changes in the reactivity worths of the reflectors and safety-rods such that initial cold criticality is achieved with only a small amount of reflector movement following the withdrawal of the safety-rods, and the removal of the scram function from the reflectors. Revised control and operating strategies have been developed and tested using the SP-100 dynamic simulation model, ARIES-GFS. The change in the total reactivity worths of the reflectors and safety-rods has eliminated the need for the use of fast and slow reflector drive speeds during the initial on-orbit approach to criticality. The relatively fast removal of the safety-rods results in a near-critical condition so that the use of slow moving (single speed) reflector drives does not add significant time to achieve full power for the initial startup. The use of the ACT system (with its NaK trace-lines for preheating and auxiliary cooling) affects the main Thermoelectric Electro-Magnetic (TEM) pump startup and the time after a shutdown before freezing occurs in the main heat transfer systems

Developing competitive advantage through startups and venture capital in emerging markets: A view from Israel.

Directory of Open Access Journals (Sweden)

Alexander Maune

2017-06-01

Full Text Available This article presents an examination of the emergence and co-evolution of startups and venture capital that led to the transformation of Israel into a Start-Up and Innovation Nation since its inception in 1948. Throughout, the co-evolution of startups and venture capital was considered a critical linkage between venture capital emergence and startup intensive cluster. The article also examined the three phased evolutionary model of 1969 to 2000. A discursive approach of related relevant literature was used. The study found out that the co-evolution of startups and venture capital, policy targeting and a network of a number of other factors as will be discussed in the three phased evolutionary model were critical to the emergence and change of the Israeli high-technology industry into a high-technology startup intensive industry. Israel has become the second largest world market for venture capital with more than 240 venture capitals since 1992. Israel has also become the lead in research and development attracting more than 270 multinational companies with more than 250 establishing research centers and employing over 108 000 in the country. The study also found that Israel leads other nations in per capita startups, engineers, scientists and technicians. This article will be critical for policy formulation and implementation especially in Emerging Markets. This article may lead to a shift in strategy in many emerging countries. This article will also help expand the academic knowledge by filling the existing gaps within the body of knowledge. Therefore, the article has academic, economic and policy value.

Track reconstruction at the ILC: the ILD tracking software

International Nuclear Information System (INIS)

Gaede, Frank; Aplin, Steven; Rosemann, Christoph; Voutsinas, Georgios; Glattauer, Robin

2014-01-01

One of the key requirements for Higgs physics at the International Linear Collider ILC is excellent track reconstruction with very good momentum and impact parameter resolution. ILD is one of the two detector concepts at the ILC. Its central tracking system comprises of an outer Si-tracker, a highly granular TPC, an intermediate silicon tracker and a pixel vertex detector, and it is complemented by silicon tracking disks in the forward direction. Large hit densities from beam induced coherent electron-positron pairs at the ILC pose an additional challenge to the pattern recognition algorithms. We present the recently developed new ILD tracking software, the pattern recognition algorithms that are using clustering techniques, Cellular Automatons and Kalman filter based track extrapolation. The performance of the ILD tracking system is evaluated using a detailed simulation including dead material, gaps and imperfections.

Plasma current start-up experiments without the central solenoid in the TST-2 spherical tokamak

International Nuclear Information System (INIS)

Takase, Y.; Ejiri, A.; Shiraiwa, S.; Adachi, Y.; Ishii, N.; Kasahara, H.; Nuga, H.; Ono, Y.; Oosako, T.; Sasaki, M.; Shimada, Y.; Sumitomo, N.; Taguchi, I.; Tojo, H.; Tsujimura, J.; Ushigome, M.; Yamada, T.; Hanada, K.; Hasegawa, M.; Idei, H.; Nakamura, K.; Sakamoto, M.; Sasaki, K.; Sato, K.N.; Zushi, H.; Nishino, N.; Mitarai, O.

2006-01-01

Several techniques for initiating the plasma current without the use of the central solenoid are being developed in TST-2. While TST-2 was temporarily located at Kyushu University, two types of start-up scenarios were demonstrated. (1) A plasma current of 4 kA was generated and sustained for 0.28 s by either electron cyclotron wave or electron Bernstein wave, without induction. (2) A plasma current of 10 kA was obtained transiently by induction using only outboard poloidal field coils. In the second scenario, it is important to supply sufficient power for ionization (100 kW of EC power was sufficient in this case), since the vertical field during start-up is not adequate to maintain plasma equilibrium. In addition, electron heating experiments using the X-B mode conversion scenario were performed, and a heating efficiency of 60% was observed at a 100 kW RF power level. TST-2 is now located at the Kashiwa Campus of the University of Tokyo. Significant upgrades were made in both magnetic coil power supplies and RF systems, and plasma experiments have restarted. RF power of up to 400 kW is available in the high-harmonic fast wave frequency range around 20 MHz. Four 200 MHz transmitters are now being prepared for plasma current start-up experiments using RF power in the lower-hybrid frequency range. Preparations are in progress for a new plasma merging experiment (UTST) aimed at the formation and sustainment of ultra-high β ST plasmas

Start-up of a drinking water biofilter

DEFF Research Database (Denmark)

Ramsay, Loren; Søborg, Ditte; Breda, Inês Lousinha Ribeiro

When virgin filter media is placed in drinking water biofilters, a start-up period of some months typically ensues. During this period, the necessary inorganic coating and bacterial community are established on the filter medium, after which the treated water complies with drinking water criteria...

Optimization of steam-vortex plasma-torch start-up

Science.gov (United States)

Mikhailov, B. I.

2011-12-01

We propose a new optimal method of steam-vortex plasma-torches start-up; this method completely prevents the danger of water steam condensation in the arc chamber and all undesirable consequences of it.

SP-100 initial startup and restart control strategy

Science.gov (United States)

Halfen, Frank J.; Wong, Kwok K.; Switick, Dennis M.; Shukla, Jaikaran N.

Startup control strategies for SP-100 are described. Revised control and operating strategies are discussed which have been developed and tested using the SP-100 dynamic simulation model Aries-GFS (Generic Flight System).

Modelling larval transport in a axial convergence front

Science.gov (United States)

Robins, P.

2010-12-01

Marine larvae exhibit different vertical swimming behaviours, synchronised by factors such as tidal currents and daylight, in order to aid retention near the parent populations and hence promote production, avoid predation, or to stimulate digestion. This paper explores two types of larval migration in an estuarine axial convergent front which is an important circulatory mechanism in many coastal regions where larvae are concentrated. A parallelised, three-dimensional, ocean model was applied to an idealised estuarine channel which was parameterised from observations of an axial convergent front which occurs in the Conwy Estuary, U.K. (Nunes and Simpson, 1985). The model successfully simulates the bilateral cross-sectional recirculation of an axial convergent front, which has been attributed to lateral density gradients established by the interaction of the lateral shear of the longitudinal currents with the axial salinity gradients. On the flood tide, there is surface axial convergence whereas on the ebb tide, there is (weaker) surface divergence. Further simulations with increased/decreased tidal velocities and with stronger/weaker axial salinity gradients are planned so that the effects of a changing climate on the secondary flow can be understood. Three-dimensional Lagrangian Particle Tracking Models (PTMs) have been developed which use the simulated velocity fields to track larvae in the estuarine channel. The PTMs take into account the vertical migrations of two shellfish species that are commonly found in the Conwy Estuary: (i) tidal migration of the common shore crab (Carcinus maenas) and (ii), diel (daily) migration of the Great scallop (Pecten maximus). These migration behaviours are perhaps the most widespread amongst shellfish larvae and have been compared with passive (drifting) particles in order to assess their relative importance in terms of larval transport. Preliminary results suggest that the net along-estuary dispersal over a typical larval

Insights from field observations into controls on flow front speed in submarine sediment flows

Science.gov (United States)

Heerema, C.; Talling, P.; Cartigny, M.; Paull, C. K.; Gwiazda, R.; Clare, M. A.; Parsons, D. R.; Xu, J.; Simmons, S.; Maier, K. L.; Chapplow, N.; Gales, J. A.; McGann, M.; Barry, J.; Lundsten, E. M.; Anderson, K.; O'Reilly, T. C.; Rosenberger, K. J.; Sumner, E. J.; Stacey, C.

2017-12-01

Seafloor avalanches of sediment called turbidity currents are one of the most important processes for moving sediment across our planet. Only rivers carry comparable amounts of sediment across such large areas. Here we present some of the first detailed monitoring of these underwater flows that is being undertaken at a series of test sites. We seek to understand the factors that determine flow front speed, and how that speed varies with distance. This frontal speed is particularly important for predicting flow runout, and how the power of these hazardous flows varies with distance. First, we consider unusually detailed measurements of flow front speed defined by transit times between moorings and other tracked objects placed on the floor of Monterey Canyon offshore California in 2016-17. These measurements are then compared to flow front speeds measured using multiple moorings in Bute Inlet, British Columbia in 2016; and by cable breaks in Gaoping Canyon offshore Taiwan in 2006 and 2009. We seek to understand how flow front velocity is related to seafloor gradient, flow front thickness and density. It appears that the spatial evolution of frontal speed is similar in multiple flows, although their peak frontal velocities vary. Flow front velocity tends to increase rapidly initially before declining rather gradually over tens or even hundreds of kilometres. It has been proposed that submarine flows will exist in one of two states; either eroding and accelerating, or depositing sediment and dissipating. We conclude by discussing the implications of this global compilation of flow front velocities for understanding submarine flow behaviour.

CR-39 track detector for multi-MeV ion spectroscopy.

Science.gov (United States)

Jeong, T W; Singh, P K; Scullion, C; Ahmed, H; Hadjisolomou, P; Jeon, C; Yun, H; Kakolee, K F; Borghesi, M; Ter-Avetisyan, S

2017-05-19

We present the characteristics of track formation on the front and rear surfaces of CR-39 produced by laser-driven protons and carbon ions. A methodological approach, based on bulk etch length, is proposed to uniquely characterize the particle tracks in CR-39, enabling comparative description of the track characteristics in different experiments. The response of CR-39 to ions is studied based on the energy dependent growth rate of the track diameter to understand the intrinsic particle stopping process within the material. A large non-uniformity in the track diameter is observed for CR-39 with thickness matching with the stopping range of particles. Simulation and experimental results show the imprint of longitudinal range straggling for energetic protons. Moreover, by exploiting the energy dependence of the track diameter, the energy resolution (δE/E) of CR-39 for few MeV protons and Carbon ion is found to be about 3%.

Urbanization and start-up rates in different geographies : Belgium, the Netherlands and Sweden

NARCIS (Netherlands)

Hans, Lianne; Koster, Sierdjan

2017-01-01

This study addresses the mediating role of settlement patterns in the relationship between urbanization and start-up activity. Places do not operate in a vacuum and to understand the effect of 'own' density on start-up patterns, we need to account for the urban spillovers or borrowed size that they

A slow pushed front in a Lotka–Volterra competition model

International Nuclear Information System (INIS)

Holzer, Matt; Scheel, Arnd

2012-01-01

We study invasion speeds in the Lotka–Volterra competition model when the rate of diffusion of one species is small. Our main result is the construction of the selected front and a rigorous asymptotic approximation of its propagation speed, valid to second order. We use techniques from geometric singular perturbation theory and geometric desingularization. The main challenge arises from the slow passage through a saddle-node bifurcation. From a perspective of linear versus nonlinear speed selection, this front provides an interesting example as the propagation speed is slower than the linear spreading speed. However, our front shares many characteristics with pushed fronts that arise when the influence of nonlinearity leads to faster than linear speeds of propagation. We show that this is a result of the linear spreading speed arising as a simple pole of the resolvent instead of as a branch pole. Using the pointwise Green's function, we show that this pole poses no a priori obstacle to marginal stability of the nonlinear travelling front, thus explaining how nonlinear systems can exhibit slower spreading that their linearization in a robust fashion

75 FR 26892 - Approval and Promulgation of Implementation Plans; Texas; Excess Emissions During Startup...

Science.gov (United States)

2010-05-13

... corrective action to avoid a malfunction, then the event is considered an unplanned maintenance activity or... Promulgation of Implementation Plans; Texas; Excess Emissions During Startup, Shutdown, Maintenance, and... Emissions Events and Scheduled Maintenance, Startup, and Shutdown Activities. This action proposes approval...

Integrated Marketing Strategies of German Companies : Start-Ups vs. Global Brands

OpenAIRE

Kostin, Irina

2016-01-01

The purpose of this bachelor's thesis is to find out and analyze different marketing strategies of German fashion companies. The main part is comparing relatively young start-up companies to established companies and analyzing to what extent the strategies differ. The methodology used in this paper were semi-structured expert interviews with German start-up companies. The results were analyzed and compared to the secondary research on the big global German companies. The findings showed that ...

Startup Ramp Rate Analysis for the OPR1000 Using FALCON Code

Energy Technology Data Exchange (ETDEWEB)

Kim, Ki-Young; Jung, Sung-hwan; Kim, Yong-Deok [Korea Hydro and Nuclear Power Co. Ltd, Daejeon (Korea, Republic of)

2015-05-15

Pelletcladding interaction (PCI) fuel failure results from a combination of mechanical and chemical interactions between the UO2 fuel pellets and Zircaloy cladding. Under restart operation conditions, the pellet-cladding gap may be closed and the differential thermal expansion can result in the stress concentrations on the cladding that may cause the fuel failure. This paper summarizes the PCI sensitivity assessment of the PLUS7 fuel during the OPR1000 startup. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. Fuel-cladding gap is closed at about 10,000 MWD/MTU burnup. Maximum hoop stress is not sensitive about change of startup ramp rate in 0 - 40% power range. Maximum hoop stress is not sensitive about the intermittent increase(1%) of startup ramp rate in 40 - 100% power range.

Startup Ramp Rate Analysis for the OPR1000 Using FALCON Code

International Nuclear Information System (INIS)

Kim, Ki-Young; Jung, Sung-hwan; Kim, Yong-Deok

2015-01-01

Pelletcladding interaction (PCI) fuel failure results from a combination of mechanical and chemical interactions between the UO2 fuel pellets and Zircaloy cladding. Under restart operation conditions, the pellet-cladding gap may be closed and the differential thermal expansion can result in the stress concentrations on the cladding that may cause the fuel failure. This paper summarizes the PCI sensitivity assessment of the PLUS7 fuel during the OPR1000 startup. The objective of the PCI analysis is to assess the cladding stress state under various power ramp conditions at the peak power node location. Fuel-cladding gap is closed at about 10,000 MWD/MTU burnup. Maximum hoop stress is not sensitive about change of startup ramp rate in 0 - 40% power range. Maximum hoop stress is not sensitive about the intermittent increase(1%) of startup ramp rate in 40 - 100% power range

Practical Considerations of the Start-up Procedure for an Active Capacitor

DEFF Research Database (Denmark)

Wang, Haoran; Wang, Qian; Geng, Tao

2017-01-01

Capacitive DC links provide the only low-impedance current path connected with an input source during the start-up of many voltage source converters. A soft-start circuit is usually implemented to limit the inrush current. A two-terminal active capacitor is recently proposed which can directly...... replace conventional passive capacitors in DC links, with reduced cost or size for a given application. The active capacitor has the same level of convenience with two power terminals only as a passive capacitor. This paper proposes two start-up schemes for the active capacitor to overcome the drawbacks...... of existing methods previously widely used for passive capacitors. One scheme is based on a trade-off design between the start-up performance and the component sizing of the active capacitor. The other scheme is based on either an additional bypass switch together with the existing soft-start circuit...

The development of eye tracking in aviation (ETA) technique to investigate pilot's cognitive processes of attention and decision-making

OpenAIRE

Li, Wen-Chin; Lin, John J. H.; Braithwaite, Graham; Greaves, Matt

2016-01-01

Eye tracking device had provided researchers a promising way to investigate what pilot‘s cognitive processes when they see information present on the flight deck. There are 35 participants consisted by pilots and avionics engineers participated in current research. The research apparatus include an eye tracker and a flight simulator divided by five AOIs for data collection. The research aims are to develop cost-efficiency of eye tracking technique in order to facilitate scientific research of...

40 CFR 68.77 - Pre-startup review.

Science.gov (United States)

2010-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 3 Prevention Program § 68.77 Pre-startup review. (a) The... stationary sources when the modification is significant enough to require a change in the process safety... substances to a process: (1) Construction and equipment is in accordance with design specifications; (2...

Historical aspects of arising and features of activity of startup companies: accounting and economic aspects

Directory of Open Access Journals (Sweden)

S.F. Legenchuk

2016-07-01

Full Text Available The history of arising and development of the concept of «startup company» have been studied and the importance of their activities have been determined. Using the largest startups (Amazon, Google, Salesforce, VMware, Facebook, Twitter, Groupon, Zynga and Аpple the main components of their activity have been determined. Because of the lack of the scientific literature that directly investigated this topic the approaches of different authors from electronic sources have been systematized and the most used of them have been analyzed. The own vision of the definition of «startup company» and its key features have been formulated as a result of the research. The place of a startup company in the system of economic categories such as an economic activity, results of company activities, accounting, analysis and risks have been determined. The impact of the consequences of risks (positive and negative of economic activity on the future of companies have been considered. The value of accounting and analysis for the economic activity of startup companies have been evaluated.

A satellite-tracking millimeter-wave reflector antenna system for mobile satellite-tracking

Science.gov (United States)

Densmore, Arthur C.; Jamnejad, Vahraz; Woo, Kenneth E.

1995-03-01

A miniature dual-band two-way mobile satellite tracking antenna system mounted on a movable ground vehicle includes a miniature parabolic reflector dish having an elliptical aperture with major and minor elliptical axes aligned horizontally and vertically, respectively, to maximize azimuthal directionality and minimize elevational directionality to an extent corresponding to expected pitch excursions of the movable ground vehicle. A feed-horn has a back end and an open front end facing the reflector dish and has vertical side walls opening out from the back end to the front end at a lesser horn angle and horizontal top and bottom walls opening out from the back end to the front end at a greater horn angle. An RF circuit couples two different signal bands between the feed-horn and the user. An antenna attitude controller maintains an antenna azimuth direction relative to the satellite by rotating it in azimuth in response to sensed yaw motions of the movable ground vehicle so as to compensate for the yaw motions to within a pointing error angle. The controller sinusoidally dithers the antenna through a small azimuth dither angle greater than the pointing error angle while sensing a signal from the satellite received at the reflector dish, and deduces the pointing angle error from dither-induced fluctuations in the received signal.

Defense waste processing facility startup progress report

International Nuclear Information System (INIS)

Iverson, D.C.; Elder, H.H.

1992-01-01

The Savannah River Site (SRS) has been operating a nuclear fuel cycle since the 1950's to produce nuclear materials in support of the national defense effort. About 83 million gallons of high level waste produced since operation began have been consolidated into 33 million gallons by evaporation at the waste tank farm. The Department of Energy has authorized the construction of the Defense Waste Processing Facility (DWPF) to immobilize the waste as a durable borosilicate glass contained in stainless steel canisters, prior to emplacement in a federal repository. The DWPF is now mechanically complete and undergoing commissioning and run-in activities. Cold startup testing using simulated non-radioactive feeds is scheduled to begin in November 1992 with radioactive operation scheduled to begin in May 1994. While technical issues have been identified which can potentially affect DWPF operation, they are not expected to negatively impact the start of non-radioactive startup testing

Determination of the uranium content in phosphate fertilizers by the fission track registration technique

International Nuclear Information System (INIS)

Rocha, A.C.S. da.

1983-01-01

The application of fission track registration technique (SSNTD) to determine the uranium contents in phosphate fertilizers is dealt with. Samples were prepared by the wet method and the detector used was Makrofol Kg 10μm thick. The determination of uranium in phosphate fertilizer industry is of considerable interest in environmental control. The roots of vegetables tend to absorb and accumulate uranium form soil and so the human body could be contaminated. The phosphate fertilizers were originated from the phosphate-rich apatite deposits located in the high naturally radioactive areas of Araxa and Tapira in the state of Minas Gerais, Brazil. The results obtained ranged from 11.1 to 100ppm of uranium with a total error from 8.2 to 15.7%. The thorium contributions to the total track counting were discounted, though the actual concentrations of thorium in the samples were not determined. (Author) [pt

The Timepix Telescope for High Performance Particle Tracking

CERN Document Server

Akiba, Kazuyoshi; van Beuzekom, Martin; van Beveren, Vincent; Borghi, Silvia; Boterenbrood, Henk; Buytaert, Jan; Collins, Paula; Dosil Suárez, Alvaro; Dumps, Raphael; Eklund, Lars; Esperante, Daniel; Gallas, Abraham; Gordon, Hamish; van der Heijden, Bas; Hombach, Christoph; Hynds, Daniel; John, Malcolm; Leflat, Alexander; Li, Yi Ming; Longstaff, Ian; Morton, Alexander; Nakatsuka, Noritsugu; Nomerotski, Andre; Parkes, Chris; Perez Trigo, Eliseo; Plackett, Richard; Reid, Matthew M; Rodriguez Perez, Pablo; Schindler, Heinrich; Szumlak, Tomasz; Tsopelas, Panagiotis; Vázquez Sierra, Carlos; Velthuis, Jaap; Wysokinski, Michal

2013-01-01

The Timepix particle tracking telescope has been developed as part of the LHCb VELO Upgrade project, supported by the Medipix Collaboration and the AIDA framework. It is a primary piece of infrastructure for the VELO Upgrade project and is being used for the development of new sensors and front end technologies for several upcoming LHC trackers and vertexing systems. The telescope is designed around the dual capability of the Timepix ASICs to provide information about either the deposited charge or the timing information from tracks traversing the 14 x 14mm matrix of 55 x 55 um pixels. The rate of reconstructed tracks available is optimised by taking advantage of the shutter driven readout architecture of the Timepix chip, operated with existing readout systems. Results of tests conducted in the SPS North Area beam facility at CERN show that the telescope typically provides reconstructed track rates during the beam spills of between 3.5 and 7.5 kHz, depending on beam conditions. The tracks are time stamped wi...

Knowledge Management in Startups: Systematic Literature Review and Future Research Agenda

Directory of Open Access Journals (Sweden)

Piera Centobelli

2017-03-01

Full Text Available This paper conducts a systematic literature review on knowledge management (KM in the context of startups in order to analyze the state of the art, identify research gaps and define a future research agenda. The main findings highlight that, even though there is an increasing number of papers on the topic of KM in startups, several issues are still neglected. Specifically, the paper identifies four main gaps in the body of literature. The first gap deals with the environmental and socio-political factors influencing the adoption of KM in startups. The second gap regards the lack of a comprehensive taxonomy of knowledge management systems (KMSs that may support the processes of knowledge creation, acquisition, storage, transfer, sharing and application. This second gap allows us to identify a third gap concerning the level of alignment between startup’s strategies and technologies adopted. Finally, the fourth gap deals with the issue of the impact of KM on startup’s performances with regard to economic, financial, market, technical, technological, organizational, human and relational performance. From these four gaps, six research questions (RQs have been proposed. These RQs allow us to identify possible areas of analysis to define a future research agenda. Neglecting these issues means underestimating all the possible advantages of KM adoption for a startup to achieve efficiency, effectiveness and scalability goals.

Experience from start-ups of the first ANITA Mox plants.

Science.gov (United States)

Christensson, M; Ekström, S; Andersson Chan, A; Le Vaillant, E; Lemaire, R

2013-01-01

ANITA™ Mox is a new one-stage deammonification Moving-Bed Biofilm Reactor (MBBR) developed for partial nitrification to nitrite and autotrophic N-removal from N-rich effluents. This deammonification process offers many advantages such as dramatically reduced oxygen requirements, no chemical oxygen demand requirement, lower sludge production, no pre-treatment or requirement of chemicals and thereby being an energy and cost efficient nitrogen removal process. An innovative seeding strategy, the 'BioFarm concept', has been developed in order to decrease the start-up time of new ANITA Mox installations. New ANITA Mox installations are started with typically 3-15% of the added carriers being from the 'BioFarm', with already established anammox biofilm, the rest being new carriers. The first ANITA Mox plant, started up in 2010 at Sjölunda wastewater treatment plant (WWTP) in Malmö, Sweden, proved this seeding concept, reaching an ammonium removal rate of 1.2 kgN/m³ d and approximately 90% ammonia removal within 4 months from start-up. This first ANITA Mox plant is also the BioFarm used for forthcoming installations. Typical features of this first installation were low energy consumption, 1.5 kW/NH4-N-removed, low N₂O emissions, started up at Sundets WWTP in Växjö, Sweden, reached full capacity with more than 90% ammonia removal within 2 months from start-up. By applying a nitrogen loading strategy to the reactor that matches the capacity of the seeding carriers, more than 80% nitrogen removal could be obtained throughout the start-up period.

Start-up strategies for thermophilic anaerobic digestion of pig manure

International Nuclear Information System (INIS)

Moset, V.; Bertolini, E.; Cerisuelo, A.; Cambra, M.; Olmos, A.; Cambra-López, M.

2014-01-01

Sludge physicochemical composition, methane (CH 4 ) yield, and methanogenic community structure and dynamics using quantitative real-time polymerase chain reaction were determined after start-up of anaerobic digestion of pig manure. Eight thermophilic continuous stirred anaerobic digesters were used during 126 days. Four management strategies were investigated: a feedless and a non-feedless period followed by a gradual or an abrupt addition of pig manure (two digesters per strategy). During the first 43 days, VFA (volatile fatty acids) accumulations and low CH 4 yield were observed in all digesters. After this period, digesters recovered their initial status being propionic acid the last parameter to be re-established. Non-feedless digesters with an abrupt addition of pig manure showed the best performances (lower VFA accumulation and higher CH 4 yield). Differences in microbial orders and dynamics, however, were less evident among treatments. Hydrogenotrophic methanogenesis, Methanomicrobiales first and Methanobacteriales second, was the dominant metabolic pathway in all digesters. Further research is needed to clarify the role and activity of hydrogenotrophic methanogens during the recovery start-up period and to identify the best molecular tools and methodologies to monitor microbial populations and dynamics reliably and accurately in anaerobic digesters. - Highlights: • Four start-up strategies for thermophilic anaerobic digestion of pig manure were tested. • Physicochemical composition, methane yield and methanogenic community were determined. • During the first 43 days, a decline in reactor's performance occurred. • The best start-up strategy was non-feedless with an abrupt addition of pig slurry. • Hydrogenotrophic methanogenesis was the dominant metabolic pathway

Simulations and field tests of a reactor coolant pump emergency start-up by means of remote gas units

International Nuclear Information System (INIS)

Omahen, P.; Gubina, F.

1992-01-01

The problem of the reactor coolant pump start-up in case of emergency by means of remote gas power plant units was analyzed. In this paper a simulation model is developed which enabled a detailed simulation of the transient process occurring at the start-up. The start-up of the RCP motor set was simulated in case of available one and two gas units. The field tests were performed and the measured variable values complied well with the simulation results. Two gas units have been determined as a safe start-up scheme of the RCP motor set considering for safety reasons accepted busbars and motor protection settings. A derived model for deep rotor bars was experimentally confirmed as effective means for the RCP motor set start-up transient simulation. Start-up procedures have been designed and adopted to the safety procedures of the Nuclear Power Plant Krsko

PIV tracer behavior on propagating shock fronts

International Nuclear Information System (INIS)

Glazyrin, Fyodor N; Mursenkova, Irina V; Znamenskaya, Irina A

2016-01-01

The present work was aimed at the quantitative particle image velocimetry (PIV) measurement of a velocity field near the front of a propagating shock wave and the study of the dynamics of liquid tracers crossing the shock front. For this goal, a shock tube with a rectangular cross-section (48  ×  24 mm) was used. The flat shock wave with Mach numbers M  =  1.4–2.0 propagating inside the tube channel was studied as well as an expanding shock wave propagating outside the channel with M  =  1.2–1.8 at its main axis. The PIV imaging of the shock fronts was carried out with an aerosol of dioctyl sebacate (DEHS) as tracer particles. The pressures of the gas in front of the shock waves studied ranged from 0.013 Mpa to 0.1 MPa in the series of experiments. The processed PIV data, compared to the 1D normal shock theory, yielded consistent values of wake velocity immediately behind the plain shock wave. Special attention was paid to the blurring of the velocity jump on the shock front due to the inertial particle lag and peculiarities of the PIV technique. A numerical algorithm was developed for analysis and correction of the PIV data on the shock fronts, based on equations of particle-flow interaction. By application of this algorithm, the effective particle diameter of the DEHS aerosol tracers was estimated as 1.03  ±  0.12 μm. A number of different formulations for particle drag were tested with this algorithm, with varying success. The results show consistency with previously reported experimental data obtained for cases of stationary shock waves. (paper)

Transport simulation of ITER [International Thermonuclear Engineering Reactor] startup

International Nuclear Information System (INIS)

Attenberger, S.E.; Houlberg, W.A.

1989-01-01

The present International Thermonuclear Engineering Reactor (ITER) reference configurations are the ''Technology Phase,'' in which the plasma current is maintained noninductively at a subignition density, and the ''Physics Phase,'' which is ignited but requires inductive maintenance of the current. The WHIST 1.5-D transport code is used to evaluate the volt-second requirements of both configurations. A slow current ramp (60-80's) is required for fixed-radius startup in ITER to avoid hollow current density profiles. To reach the operating point requires about 203 V·s for the Technology Phase (18 MA) and about 270 V·s for the Physics Phase (22 MA). The resistive losses can be reduced with expanding-radius startup. 5 refs., 4 figs

Knowledge Management in Startups: Systematic Literature Review and Future Research Agenda

OpenAIRE

Piera Centobelli; Roberto Cerchione; Emilio Esposito

2017-01-01

This paper conducts a systematic literature review on knowledge management (KM) in the context of startups in order to analyze the state of the art, identify research gaps and define a future research agenda. The main findings highlight that, even though there is an increasing number of papers on the topic of KM in startups, several issues are still neglected. Specifically, the paper identifies four main gaps in the body of literature. The first gap deals with the environmental and socio-poli...

Identifying Tracks Duplicates via Neural Network

CERN Document Server

Sunjerga, Antonio; CERN. Geneva. EP Department

2017-01-01

The goal of the project is to study feasibility of state of the art machine learning techniques in track reconstruction. Machine learning techniques provide promising ways to speed up the pattern recognition of tracks by adding more intelligence in the algorithms. Implementation of neural network to process of track duplicates identifying will be discussed. Different approaches are shown and results are compared to method that is currently in use.

Track benchmarking method for uncertainty quantification of particle tracking velocimetry interpolations

International Nuclear Information System (INIS)

Schneiders, Jan F G; Sciacchitano, Andrea

2017-01-01

The track benchmarking method (TBM) is proposed for uncertainty quantification of particle tracking velocimetry (PTV) data mapped onto a regular grid. The method provides statistical uncertainty for a velocity time-series and can in addition be used to obtain instantaneous uncertainty at increased computational cost. Interpolation techniques are typically used to map velocity data from scattered PTV (e.g. tomographic PTV and Shake-the-Box) measurements onto a Cartesian grid. Recent examples of these techniques are the FlowFit and VIC+  methods. The TBM approach estimates the random uncertainty in dense velocity fields by performing the velocity interpolation using a subset of typically 95% of the particle tracks and by considering the remaining tracks as an independent benchmarking reference. In addition, also a bias introduced by the interpolation technique is identified. The numerical assessment shows that the approach is accurate when particle trajectories are measured over an extended number of snapshots, typically on the order of 10. When only short particle tracks are available, the TBM estimate overestimates the measurement error. A correction to TBM is proposed and assessed to compensate for this overestimation. The experimental assessment considers the case of a jet flow, processed both by tomographic PIV and by VIC+. The uncertainty obtained by TBM provides a quantitative evaluation of the measurement accuracy and precision and highlights the regions of high error by means of bias and random uncertainty maps. In this way, it is possible to quantify the uncertainty reduction achieved by advanced interpolation algorithms with respect to standard correlation-based tomographic PIV. The use of TBM for uncertainty quantification and comparison of different processing techniques is demonstrated. (paper)

Improvement of operational efficiency based on fast startup plant concepts

Energy Technology Data Exchange (ETDEWEB)

Grumann, Ulrich; Kurz, Harald; Meinecke, Gero; Pickard, Andreas

2010-09-15

The power generation sector is currently confronted with new challenges relating to the conservation of dwindling fuel reserves. At the same time we must reduce CO2 emissions in order to counteract global warming. This paper shows that power plant operation, which employs shutdowns during periods of low load demand coupled with the optimization of startup procedures are a key to reducing CO2 emissions and to conserving resources. The startup technology developed by Siemens also offers grid support in the event of naturally occurring failures of renewable energy sources. Additionally, plant profitability is improved due to the resulting savings in fuel.

CERN confident of LHC start-up in 2007

CERN Document Server

2007-01-01

"Delegates attending the 140th meeting of CERN Council heard a confident report from the Laboratory about the scheduled start-up of the world's highest energy particle accelerator, the Large Hadron Collier (LHC), in 2007." (1 page)

HINS Linac front end focusing system R&D

Energy Technology Data Exchange (ETDEWEB)

Apollinari, G.; Carcagno, R.H.; Dimarco, J.; Huang, Y.; Kashikhin, V.V.; Orris, D.F.; Page, T.M.; Rabehl, R.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; /Fermilab /Argonne

2008-08-01

This report summarizes current status of an R&D program to develop a focusing system for the front end of a superconducting RF linac. Superconducting solenoids will be used as focusing lenses in the low energy accelerating sections of the front end. The development of focusing lenses for the first accelerating section is in the production stage, and lens certification activities are in preparation at FNAL. The report contains information about the focusing lens design and performance, including solenoid, dipole corrector, and power leads, and about cryogenic system design and performance. It also describes the lens magnetic axis position measurement technique and discusses scope of an acceptance/certification process.

Trace uranium determination in beverages and mineral water using fission track techniques

International Nuclear Information System (INIS)

Cheng, Y.L.; Lin, J.Y.; Hao, X.H.

1993-01-01

The uranium contents of beverages and mineral water have been estimated using the technique of fission track analysis with polycarbonate detector. The U contents in beverages have been found to vary from 0.26 ± 0.03 to 1.65 ± 0.07 ppb, the average value is 0.93 ± 0.05 ppb. The mean U content in mineral water is 9.20 ± 0.16 ppb, which is ∼ 10 times higher than the mean U content of beverages. The present study shows the high U content in mineral water, indicating need for further investigation of U content in mineral water for the studies of radiation health hazards. (Author)

Using Social Media to Accelerate the Internationalization of Startups from Inception

Directory of Open Access Journals (Sweden)

Tony Maltby

2012-10-01

Full Text Available A set of principles, processes, and tools that entrepreneurs can use to rapidly internationalize their technology startups from inception does not exist. This article discusses entrepreneurs’ use of online social media networks to rapidly internationalize their startups from inception. The article was inspired by how the founders of Dewak S.A. rapidly internationalized their technology startup. Dewak was founded by five unemployed Colombians in June 2008. Two years later, foreign sales comprised 95% of the firm’s revenue and provided the founders with full-time employment. Dewak’s only channel to market was via online social media networks. Recognizing that entrepreneurs can use social media to amplify their tacit knowledge and convert it into sellable products and services contributes to the development of a learning-based view of rapid internationalization from inception. The article provides entrepreneurs seeking to launch and grow global businesses with four recommendations that may save them time and money and increase the size of their addressable markets.

Influence of the feeding regime on the start-up and operation of the ...