A system to measure isomeric state half-lives in the 10 ns to 10 μs range

Science.gov (United States)

Toufen, D. L.; Allegro, P. R. P.; Medina, N. H.; Oliveira, J. R. B.; Cybulska, E. W.; Seale, W. A.; Linares, R.; Silveira, M. A. G.; Ribas, R. V.

2014-07-01

The Isomeric State Measurement System (SISMEI) was developed to search for isomeric nuclear states produced by fusion-evaporation reactions. The SISMEI consists of 10 plastic phoswich telescopes, two lead shields, one NaI(Tl) scintillation detector, two Compton suppressed HPGe γ-ray detectors, and a cone with a recoil product catcher. The new system was tested at the 8 UD Pelletron tandem accelerator of the University of São Paulo with the measurement of two known isomeric states: 54Fe, 10+ state (E = 6527.1 (11) keV, T1/2 = 364(7) ns) and the 5/2+ state of 19F (E = 197.143 (4) keV, T1/2 = 89.3 (10) ns). The results indicate that the system is capable of identifying delayed transitions, of measuring isomeric state lifetimes, and of identifying the feeding transitions of the isomeric state through the delayed γ-γ coincidence method. The measured half-life for the 10+ state was T1/2 = 365(14) ns and for the 5/2+ state, 100(36) ns.

Ion exchange and electrochemical evaluation of the microporous phosphate Li9Fe7(PO4)10

International Nuclear Information System (INIS)

Becht, Gregory A.; Vaughey, John T.; Britt, Robin L.; Eagle, Cassandra T.; Hwu, Shiou-Jyh

2008-01-01

A new lithium iron(III) phosphate, Li 9 Fe 7 (PO 4 ) 10 , has been synthesized and is currently under electrochemical evaluation as an anode material for rechargeable lithium-ion battery applications. The sample was prepared via the ion exchange reaction of Cs 5 K 4 Fe 7 (PO 4 ) 10 1 in the 1 M LiNO 3 solution under hydrothermal conditions at 200 deg. C. The fully Li + -exchanged sample Li 9 Fe 7 (PO 4 ) 10 2 cannot yet be synthesized by conventional high-temperature, solid-state methods. The parent compound 1 is a member of the Cs 9-x K x Fe 7 (PO 4 ) 10 series that was previously isolated from a high-temperature (750 deg. C) reaction employing the eutectic CsCl/KCl molten salt. The polycrystalline solid 1 was first prepared in a stoichiometric reaction via conventional solid-state method then followed by ion exchange giving rise to 2. Both compounds adopt three-dimensional structures that consist of orthogonally interconnected channels where electropositive ions reside. It has been demonstrated that the Cs 9-x K x Fe 7 (PO 4 ) 10 series possesses versatile ion exchange capabilities with all the monovalent alkali metal and silver cations due to its facile pathways for ion transport. 1 and 2 were subject to electrochemical analysis and preliminary results suggest that the latter can be considered as an anode material. Electrochemical results indicate that Li 9 Fe 7 (PO 4 ) 10 is reduced below 1 V (vs. Li) to most likely form a Fe(0)/Li 3 PO 4 composite material, which can subsequently be cycled reversibly at relatively low potential. An initial capacity of 250 mAh/g was measured, which is equivalent to the insertion of thirteen Li atoms per Li 9+x Fe 7 (PO 4 ) 10 (x = 13) during the charge/discharge process (Fe 2+ + 2e → Fe 0 ). Furthermore, 2 shows a lower reduction potential (0.9 V), by approximately 200 mV, and much better electrochemical reversibility than iron(III) phosphate, FePO 4 , highlighting the value of improving the ionic conductivity of the sample

Intrinsic Properties of Fe-Substituted L1(0) Magnets

Energy Technology Data Exchange (ETDEWEB)

Manchanda, P; Kumar, P; Kashyap, A; Lucis, MJ; Shield, JE; Mubarok, A; Goldstein, JI; Constantinides, S; Barmak, K; Lewis, LH; Sellmyer, DJ; Skomski, R

2013-10-01

First-principle supercell calculations are used to determine how 3d elemental additions, especially Fe additions, modify the magnetization, exchange and anisotropy of L1(0)-ordered ferromagnets. Calculations are performed using the VASP code and partially involve configurational averaging over site disorder. Three isostructural systems are investigated: Fe-Co-Pt, Mn-Al-Fe, and transition metal-doped Fe-Ni. In all three systems the iron strongly influences the magnetic properties of these compounds, but the specific effect depends on the host. In CoPt(Fe) iron enhances the magnetization, with subtle changes in the magnetic moments that depend on the distribution of the Fe and Co atoms. The addition of Fe to MnAl is detrimental to the magnetization, because it creates antiferromagnetic exchange interactions, but it enhances the magnetic anisotropy. The replacement of 50% of Mn by Fe in MnFeAl2 enhances the anisotropy from 1.77 to 2.5 MJ/m(3). Further, the substitution of light 3d elements such as Ti, V, Cr into L1(0)-ordered FeNi is shown to substantially reduce the magnetization.

Anomalous superconducting spin-valve effect in NbN/FeN/Cu/FeN/FeMn multilayers

Energy Technology Data Exchange (ETDEWEB)

Hwang, Tae Jong; Kim, Dong Ho [Yeungnam University, Gyeongsan (Korea, Republic of)

2017-09-15

We have studied magnetic and transport properties of NbN/FeN/Cu/FeN/FeMn spin-valve structure. In-plane magnetic moment exhibited typical hysteresis loops of spin valves in the normal state of NbN film at 20 K. On the other hand, the magnetic hysteresis loop in the superconducting state exhibited more complex behavior in which exchange bias provided by antiferrmagnetic FeMn layer to adjacent FeN layer was disturbed by superconductivity. Because of this, the ideal superconducting spin-valve effect was not detected. Instead the stray field originated from unsaturated magnetic states dominated the transport properties of NbN/FeN/Cu/FeN/FeMn multilayer.

The origin of high magnetic properties in (R,Zr)(Fe,Co){sub 11.0–11.5}Ti{sub 1.0–0.5}N{sub y} (y=1.0–1.4 for R=Nd, y=0 for R=Sm) compounds

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, K., E-mail: koba@ms.sist.ac.jp [Shizuoka Institute of Science and Technology, 2200-2 Toyosawa, Fukuroi, Shizuoka 437-8555 (Japan); Suzuki, S.; Kuno, T.; Urushibata, K. [Shizuoka Institute of Science and Technology, 2200-2 Toyosawa, Fukuroi, Shizuoka 437-8555 (Japan); Sakuma, N.; Yano, M.; Shoji, T.; Kato, A. [Toyota Motor Corporation, 1200 Mishuku, Susono, Shizuoka 410-1193 (Japan); Technology Reserch Association of Magnetic Materials fot High-efficiency Motors (Mag-HEM) Higashifuji-Branch, 1200 Mishuku, Susono, Shizuoka 410-1193, Japan. (Japan); Manabe, A. [Technology Reserch Association of Magnetic Materials fot High-efficiency Motors (Mag-HEM) Higashifuji-Branch, 1200 Mishuku, Susono, Shizuoka 410-1193, Japan. (Japan)

2017-03-15

Ten alloys and nitrogenated compounds of (R,Zr)(Fe,Co){sub 11.0–11.5}Ti{sub 1.0–0.5}N{sub y} (y=1.0–1.4 for R=Nd, y=0 for R=Sm) with a ThMn{sub 12}-type structure were prepared. The average Fe–Fe interatomic distances, d(Fe–Fe), for Fe sites were calculated based on the reported atomic parameters. The hyperfine splittings (inner field (IF), in teslas) were measured by Mössbauer spectroscopy, and the IF increased with increasing d(Fe–Fe) for Fe sites, indicating a magneto-volume effect. The order of IF magnitude in Fe sites was Fe(8i)>Fe(8j)>Fe(8f) in all alloys. Co substitution for Fe sites, (Fe{sub 0.75}Co{sub 0.25}), increased the IF by 25% for the R=Nd alloy and 15% for the R=Sm alloy. Decreasing Ti content from −Ti{sub 1.0} to −Ti{sub 0.5}, which increased the Fe and Co content, preserved the ThMn{sub 12} structure with Zr substitution for R(2a) sites, and caused a slight increase in the IF of 2% for the R=Nd alloy and 7% for the R=Sm alloy. Nitrogenation, where N was introduced into the 2b sites, also increased IF in R=Nd alloys, by 23% for the Co- and Zr-free alloys, NdFe{sub 11}Ti{sub 1.0}N{sub 1.5}, and by 7% for the Co-containing, (Nd{sub 0.7}Zr{sub 0.3}) (Fe{sub 0.75}Co{sub 0.25}) {sub 11.5}Ti{sub 0.5}N{sub 1.3} alloy. The IF values of the R=Nd alloys were slightly larger than those of the R=Sm alloys. In conclusion, the magneto-volume effect was clearly observed at the Fe sites, and Co substitution into Fe sites and nitrogenation (R=Nd alloys) compensated for the increased IF. Increasing the Fe and Co fractions also increased IF slightly. - Highlights: • Average distances of Fe–Fe (d(Fe–Fe)) were calculated using lattice constants. • Hyperfine fields (IF) in Fe sites were measured using Mössbauer spectroscopy. • Relationship between d(Fe–Fe) and IF at each Fe site was obtained. • Co substitution and N introduction effects on IF was also measured. • Magneto-volume effect is main reason of IF augmentation in Fe sites.

12 CFR 541.10 - Dwelling unit.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Dwelling unit. 541.10 Section 541.10 Banks and... FEDERAL SAVINGS ASSOCIATIONS § 541.10 Dwelling unit. The term dwelling unit means the unified combination of rooms designed for residential use by one family, other than a single-family dwelling. ...

Climate Prediction Center (CPC) 6 to 10 Day Probabilistic Precipitation Outlook for the Contiguous United States and Alaska

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Climate Prediction Center (CPC) issues 6 to 10 day probabilistic precipitation outlooks for the United States. The 6-10 day Outlook gives the confidence that a...

Climate Prediction Center (CPC) 6 to 10 Day Probabilistic Temperature Outlook for the Contiguous United States and Alaska

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Climate Prediction Center (CPC) issues 6 to 10 day probabilistic temperature outlooks for the United States. The 6-10 day Outlook gives the confidence that a...

Cinética de engrosamiento de precipitados coherentes en la aleación Fe-10 % Ni-15 % Al

Directory of Open Access Journals (Sweden)

Cayetano-Castro, N.

2008-04-01

Full Text Available The coarsening kinetics and the morphology evolution of the coherent β’ (Fe, NiAl precipitates embedded in a ferritic matrix were studied in the aged Fe-10 % Ni-15 % Al alloy. Samples were solution treated at 1,100°C for 24 h and subsequently aged at 750, 850 and 920 °C for different times. XRD, SEM and TEM results showed the following decomposition reaction after aging treatment, α_sss → α + β. Intragranular particles distribution changes from a random to an aligned on the elastically soft <100> crystallographic directions of the matrix. Additionally, the morphological evolution of the precipitates was as follows: spheres → cuboids → parallelepipeds → plates. The variation of the cube of mean radius of particles, r³, and the particle density as a function of time followed a linear relationship, as predicted by the Lifshitz, Slyosov and Wagner (LSW theory for diffusion-controlled coarsening. The rate constant (K increased with the aging temperature. The activation energy for coarsening process was determined to be about of 220 kJ/mol.

La cinética de engrosamiento y la evolución morfológica de precipitados coherentes β’ (Fe, NiAl en una matriz ferrítica se estudió en la aleación Fe-10 % Ni-15 % Al. Se solubilizaron muestras a 1.100 °C por 24, y posteriormente, se envejecieron a 750, 850 y 920 °C por diferentes tiempos. Los resultados de DRX, MEB y MET mostraron la descomposición, α_sss → α + β, durante su envejecido. La distribución de precipitados dentro del grano cambia, gradualmente, de aleatoria a un alineamiento preferencial sobre las direcciones cristalográficas <100> de la matriz. Asimismo, la evolución morfológica de los precipitados fue: esféricos → cúbicos → paralelepípedos → placas. La variación del tamaño de partícula, r³, y la densidad de precipitados en función del tiempo se comportan linealmente, como lo predice la teoría de Lifshitz

Magnetoresistance and magnetostriction of Ni81Fe19 and Co90Fe10 mono- and bilayer films

International Nuclear Information System (INIS)

Sahingoz, R.; Hollingworth, M.P.; Gibbs, M.R.J.; Murdoch, S.J.

2005-01-01

Monolayer and bilayer films of Ni 81 Fe 19 , Co 90 Fe 10 , Co 90 Fe 10 /Ni 81 Fe 19 , and Ni 81 Fe 19 /Co 90 Fe 10 have been grown on thermally oxidized Si. The magnetoresistance (MR) of the samples was measured as a function of applied DC magnetic field, using a four-point probe method. The magnetostriction constant, λ s , was derived from the change of anisotropy field as a function of strain. The dependence of the MR on different combinations of film layers was investigated. The magnetoresistance of the bilayers changed dramatically upon reversal of the layer order. The mono- and bilayer samples with the same material on top of the substrate showed similar MR loop shapes. However, the saturation fields of the bilayers were larger than those for the monolayers. The magnetostriction of all samples was negative. We discuss the consequences for the study and optimization of spin-valve devices

77 FR 25375 - United States Standards for Wheat

Science.gov (United States)

2012-04-30

... and Stockyards Administration 7 CFR Part 810 RIN 0580-AB12 United States Standards for Wheat... 20.0 Wheat of other classes: \\2\\ Contrasting classes 1.0 2.0 3.0 10.0 10.0 Total \\3\\ 3.0 5.0 10.0 10...

78 FR 69703 - 10-Day Notice of Proposed Information Collection: Generic Customer Satisfaction Surveys; Physical...

Science.gov (United States)

2013-11-20

... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5683-N-102] 10-Day Notice of Proposed Information Collection: Generic Customer Satisfaction Surveys; Physical Inspection Pilot Program...

75 FR 60680 - Designation of Areas for Air Quality Planning Purposes; State of Arizona; Pinal County; PM10

Science.gov (United States)

2010-10-01

... the Apache Junction area within Pinal County; and the Hayden/Miami planning area, which includes the... the Hayden/ Miami PM 10 nonattainment area into two separate PM 10 nonattainment areas. See 72 FR... Apache Reservation lies in the existing Hayden PM 10 nonattainment area. The rest of the Pinal County...

10 CFR 904.10 - Excess energy.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Excess energy. 904.10 Section 904.10 Energy DEPARTMENT OF ENERGY GENERAL REGULATIONS FOR THE CHARGES FOR THE SALE OF POWER FROM THE BOULDER CANYON PROJECT Power Marketing § 904.10 Excess energy. (a) If excess Energy is determined by the United States to be available...

Spin dynamics and thermal stability in L10 FePt

Science.gov (United States)

Chen, Tianran; Toomey, Wahida

Increasing the data storage density of hard drives remains one of the continuing goals in magnetic recording technology. A critical challenge for increasing data density is the thermal stability of the written information, which drops rapidly as the bit size gets smaller. To maintain good thermal stability in small bits, one should consider materials with high anisotropy energy such as L10 FePt. High anisotropy energy nevertheless implies high coercivity, making it difficult to write information onto the disk. This issue can be overcome by a new technique called heat-assisted magnetic recording, where a laser is used to locally heat the recording medium to reduce its coercivity while retaining relatively good thermal stability. Many of the microscopic magnetic properties of L10 FePt, however, have not been theoretically well understood. In this poster, I will focus on a single L10 FePt grain, typically of a few nanometers. Specifically, I will discuss its critical temperature, size effect and, in particular, spin dynamics in the writing process, a key to the success of heat-assisted magnetic recording. WCU URF16.

(C2N2H10)[Fe xV1-x(HPO3)F3] (x = 0.44, 0.72): Two new organically templated phosphites

International Nuclear Information System (INIS)

Cisneros, Jose L.; Fernandez-Armas, Sergio; Mesa, Jose L.; Pizarro, Jose L.; Arriortua, Maria I.; Rojo, Teofilo

2006-01-01

(C 2 N 2 H 10 )[Fe x V 1-x (HPO 3 )F 3 ] (x = 0.44, 0.72) have been synthesized using mild solvothermal conditions under autogenous pressure and the ethylenediamine molecule as templating agent. The crystal structures have been determined from X-ray single-crystal diffraction data. The compounds crystallize in the orthorhombic P2 1 2 1 2 1 space group with Z = 4 and unit-cell parameters a = 12.8494(9), b = 9.5430(6), c = 6.4372(5) A, and a = 12.8578(1), b = 9.5342(1), c = 6.4370(7) A for (C 2 N 2 H 10 )[Fe 0.44 V 0.56 (HPO 3 )F 3 ] and (C 2 N 2 H 10 )[Fe 0.72 V 0.28 (HPO 3 )F 3 ] (1) and (2), respectively. These isostructural compounds exhibit a monodimensional crystal structure formed by pillared double anionic chains with the formula [M(HPO 3 )F 3 ] 2- , extended along the [0 0 1] direction. These doubled ionic chains are the result of the linking of two simple chains in which there are alternating octahedral [MO 3 F 3 ] and tetrahedral groups [HPO 3 ]. The ethylendiammonium cations are placed in the space delimited by three different chains. The metallic ions are interconnected by the pseudo-pyramidal (HPO 3 ) 2- phosphite oxoanions, adopting a slightly distorted octahedral geometry. The IR spectra show bands corresponding to the phosphite oxoanion and the ethylendiamonium cation at 2400 and 1600 cm -1 , respectively. The thermogravimetric analyses show that these phases are stable up to ca. 280 deg. C, at higher temperatures, the decomposition of the crystal structure begins by calcination of the organic cation and the elimination of the fluoride anions. The diffuse reflectance spectra show bands of the V 3+ ion (d 2 ) in octahedral symmetry. The values of the Dq (1540, 1540 cm -1 ), and Racah parameters, B (560, 535 cm -1 ) and C (3055, 3140 cm -1 ) for (1) and (2), respectively, correspond with those usually found for octahedrically coordinated V(III) compounds. Magnetic measurements, performed on a powered sample from 5.0 to 300 K at 1000 G, in the ZFC and

The fluctuation field and anomalous magnetic viscosity in commercial NdFeB alloys, AlNiCo and the bulk amorphous ferromagnets Nd{sub 60}Fe{sub 30}Al{sub 10} and Nd{sub 60}Fe{sub 20}Co{sub 10}Al{sub 10}

Energy Technology Data Exchange (ETDEWEB)

Collocott, S.J. [CSIRO Materials Science and Engineering, Lindfield, NSW 2070 (Australia)], E-mail: stephen.collocott@csiro.au; Dunlop, J.B. [CSIRO Materials Science and Engineering, Lindfield, NSW 2070 (Australia)

2008-08-15

The fluctuation field, H{sub f}, is a useful parameter for characterising any ferromagnetic material that displays hysteresis, as it is a measure of the thermally activated rate processes that govern magnetisation reversals. Anomalous magnetic viscosity, i.e. nonmonotonic behaviour of the time dependent magnetisation, where the magnetisation is seen to increase, reach a peak, and then decrease, has been observed on both the upper and lower branches of minor loops or recoil curves in some ferromagnetic materials. Parameters relevant to the Preisach model are discussed as to their usefulness in predicting anomalous magnetic viscosity in ferromagnetic materials. This is done with reference to measurements of H{sub f} and the time dependent magnetisation in commercial NdFeB alloys, AlNiCo and the bulk amorphous ferromagnets Nd{sub 60}Fe{sub 30}Al{sub 10} and Nd{sub 60}Fe{sub 20}Co{sub 10}Al{sub 10}.

76 FR 9399 - Department of State FY10 Service Contract Inventory

Science.gov (United States)

2011-02-17

... DEPARTMENT OF STATE [Public Notice 7321] Department of State FY10 Service Contract Inventory... Contract Inventory. SUMMARY: The Department of State has publically released its Service Contract Inventory for FY10. Section 743 of Division C of the FY 2010 Consolidated Appropriations Act, Public Law 111-117...

Photoexcited carrier trapping and recombination at Fe centers in GaN

International Nuclear Information System (INIS)

Uždavinys, T. K.; Marcinkevičius, S.; Leach, J. H.; Evans, K. R.; Look, D. C.

2016-01-01

Fe doped GaN was studied by time-resolved photoluminescence (PL) spectroscopy. The shape of PL transients at different temperatures and excitation powers allowed discrimination between electron and hole capture to Fe"3"+ and Fe"2"+ centers, respectively. Analysis of the internal structure of Fe ions and intra-ion relaxation rates suggests that for high repetition rates of photoexciting laser pulses the electron and hole trapping takes place in the excited state rather than the ground state of Fe ions. Hence, the estimated electron and hole capture coefficients of 5.5 × 10"−"8 cm"3/s and 1.8 × 10"−"8 cm"3/s should be attributed to excited Fe"3"+ and Fe"2"+ states. The difference in electron capture rates determined for high (MHz) and low (Hz) (Fang et al., Appl. Phys. Lett. 107, 051901 (2015)) pulse repetition rates may be assigned to the different Fe states participating in the carrier capture. A weak temperature dependence of the electron trapping rate shows that the potential barrier for the multiphonon electron capture is small. A spectral feature observed at ∼420 nm is assigned to the radiative recombination of an electron in the ground Fe"2"+ state and a bound hole.

TEM study on a new Zr-(Fe, Cu) phase in furnace-cooled Zr-1.0Sn-0.3Nb-0.3Fe-0.1Cu alloy

Science.gov (United States)

Liu, Yushun; Qiu, Risheng; Luan, Baifeng; Hao, Longlong; Tan, Xinu; Tao, Boran; Zhao, Yifan; Li, Feitao; Liu, Qing

2018-06-01

A new Zr-(Fe, Cu) phase was found in furnace-cooled Zr-1.0Sn-0.3Nb-0.3Fe- 0.1Cu alloy and alloys aged at 580 °C for 10min, 2 h and 10 h. Electron diffraction experiment shows the crystal structure of this phase to be body-centered tetragonal with unit cell dimensions determined to be a = b = 6.49 Å, c = 5.37 Å. Its possible space groups have been discussed and the reason accounting for its formation is believed to be the addition of Cu according to the atom-level images. In addition, no crystal structural or chemical composition changes were observed throughout the aging process.

Investigations of neutron-rich nuclei at the dripline through their analogue states : The cases of $^{10}$Li - $^{10}$Be (T=2) and $^{17}$C - $^{17}$N (T=5/2)

CERN Multimedia

2002-01-01

We propose to study the elastic resonance scattering reactions $^{9}$Li+p and $^{16}$C+p to investigate the energies, spins and parities of the lowest T=2 states in $^{10}$Be and the T=5/2 states in $^{17}$N. These are analogue states of the ground states and first excited states in $^{10}$Li and $^{17}$C.

The origin of high magnetic properties in (R,Zr)(Fe,Co)11.0–11.5Ti1.0–0.5Ny (y=1.0–1.4 for R=Nd, y=0 for R=Sm) compounds

International Nuclear Information System (INIS)

Kobayashi, K.; Suzuki, S.; Kuno, T.; Urushibata, K.; Sakuma, N.; Yano, M.; Shoji, T.; Kato, A.; Manabe, A.

2017-01-01

Ten alloys and nitrogenated compounds of (R,Zr)(Fe,Co) 11.0–11.5 Ti 1.0–0.5 N y (y=1.0–1.4 for R=Nd, y=0 for R=Sm) with a ThMn 12 -type structure were prepared. The average Fe–Fe interatomic distances, d(Fe–Fe), for Fe sites were calculated based on the reported atomic parameters. The hyperfine splittings (inner field (IF), in teslas) were measured by Mössbauer spectroscopy, and the IF increased with increasing d(Fe–Fe) for Fe sites, indicating a magneto-volume effect. The order of IF magnitude in Fe sites was Fe(8i)>Fe(8j)>Fe(8f) in all alloys. Co substitution for Fe sites, (Fe 0.75 Co 0.25 ), increased the IF by 25% for the R=Nd alloy and 15% for the R=Sm alloy. Decreasing Ti content from −Ti 1.0 to −Ti 0.5 , which increased the Fe and Co content, preserved the ThMn 12 structure with Zr substitution for R(2a) sites, and caused a slight increase in the IF of 2% for the R=Nd alloy and 7% for the R=Sm alloy. Nitrogenation, where N was introduced into the 2b sites, also increased IF in R=Nd alloys, by 23% for the Co- and Zr-free alloys, NdFe 11 Ti 1.0 N 1.5 , and by 7% for the Co-containing, (Nd 0.7 Zr 0.3 ) (Fe 0.75 Co 0.25 ) 11.5 Ti 0.5 N 1.3 alloy. The IF values of the R=Nd alloys were slightly larger than those of the R=Sm alloys. In conclusion, the magneto-volume effect was clearly observed at the Fe sites, and Co substitution into Fe sites and nitrogenation (R=Nd alloys) compensated for the increased IF. Increasing the Fe and Co fractions also increased IF slightly. - Highlights: • Average distances of Fe–Fe (d(Fe–Fe)) were calculated using lattice constants. • Hyperfine fields (IF) in Fe sites were measured using Mössbauer spectroscopy. • Relationship between d(Fe–Fe) and IF at each Fe site was obtained. • Co substitution and N introduction effects on IF was also measured. • Magneto-volume effect is main reason of IF augmentation in Fe sites.

Study of the reaction of astrophysical interest 60Fe(n,γ)61Fe via (d,pγ) transfer reaction

International Nuclear Information System (INIS)

Giron, S.

2011-12-01

60 Fe is of special interest in nuclear astrophysics. Indeed the recent observations of 60 Fe characteristic gamma-ray lines by the RHESSI and INTEGRAL spacecrafts allowed to measure the total flux of 60 Fe over the Galaxy. Moreover the observation in presolar grains of an excess of the daughter-nuclei of 60 Fe, 60 Ni, gives constraints on the conditions of formation of the early solar system. However, the cross-sections of some reactions involved in 60 Fe nucleosynthesis and included to stellar models are still uncertain. The destruction reaction of 60 Fe, 60 Fe(n, γ) 61 Fe, is one of them. The total cross-section can be separate into two contributions: the direct one, involving states below the neutron separation threshold of 61 Fe, and the resonant one.We improved 61 Fe spectroscopy in order to evaluate the direct capture part of the 60 Fe(n, γ) 61 Fe reaction cross-section. 60 Fe(n, γ) 61 Fe was thus studied via d( 60 Fe, pγ) 61 Fe transfer reaction with the CATS/MUST2/EXOGAM setup at LISE-GANIL. DWBA analysis of experimental proton differential cross-sections allowed to extract orbital angular momentum and spectroscopic factors of different populated states identified below the neutron threshold. A comparison of experimental results for 61 Fe with experimental results for similar nuclei and with shell-model calculations was also performed. (author) [fr

Cross sections for the reactions 54Fe(n,α)51Cr, 54Fe(n,p)54Mn, and 56Fe(n,p)56Mn

International Nuclear Information System (INIS)

Paulsen, A.; Widera, R.; Arnotte, F.; Liskien, H.

1979-01-01

Ratios of cross sections for the reactions 54 Fe(n,α) 51 Cr, 54 Fe(n,p) 54 Mn, and 56 Fe(n,p) 56 Mn were measured by the activation technique. In the 6- to 10-MeV energy range, quasi-monoenergetic neutrons produced by the D(d,n) source reaction were used, while additional data were obtained between 12 and 17 MeV by use of the T(d,n) source reaction. The cross-section ratios have accuracies between 1.5 and 4.5%. 1 figure, 3 tables

Design and Micromagnetic Simulation of Fe/L10-FePt/Fe Trilayer for Exchange Coupled Composite Bit Patterned Media at Ultrahigh Areal Density

Directory of Open Access Journals (Sweden)

Warunee Tipcharoen

2015-01-01

Full Text Available Exchange coupled composite bit patterned media (ECC-BPM are one candidate to solve the trilemma issues, overcome superparamagnetic limitations, and obtain ultrahigh areal density. In this work, the ECC continuous media and ECC-BPM of Fe/L10-FePt/Fe trilayer schemes are proposed and investigated based on the Landau-Lifshitz-Gilbert equation. The switching field, Hsw, of the hard phase in the proposed continuous ECC trilayer media structure is reduced below the maximum write head field at interlayer exchange coupling between hard and soft phases, Aex, higher than 20 pJ/m and its value is lower than that for continuous L10-FePt single layer media and L10-FePt/Fe bilayer. Furthermore, the Hsw of the proposed ECC-BPM is lower than the maximum write head field with exchange coupling coefficient between neighboring dots of 5 pJ/m and Aex over 10 pJ/m. Therefore, the proposed ECC-BPM trilayer has the highest potential and is suitable for ultrahigh areal density magnetic recording technology at ultrahigh areal density. The results of this work may be gainful idea for nanopatterning in magnetic media nanotechnology.

Resistencia a la corrosión atmosférica del recubrimiento Zn-10,2% Fe sobre chapa de acero. Comparación con el recubrimiento de zinc

Directory of Open Access Journals (Sweden)

Arnau, G.

1998-05-01

Full Text Available Zn-10.2 % Fe galvanized coating versus hot galvanized coating over carbon steel corrosion performance has been studied. Different periods of atmospheric exposures in various Valencia Community sites, and salt spray accelerated test have been done. Carbon steel test samples have been used simultaneously in order to classify exposure atmosphere corrosivity, and environmental exposure atmosphere characteristics have been analyzed. Corrosion velocity versus environmental parameters has been obtained.

Se estudia el comportamiento a la corrosión atmosférica de un recubrimiento Zn-10,2 % Fe galvanizado en caliente, comparándolo con el comportamiento ofrecido por la chapa galvanizada, habiéndose aplicado ambos recubrimientos sobre chapa de acero de embutición. Se han realizado ensayos de exposición atmosférica en distintas atmósferas de la Comunidad Valenciana y ensayos acelerados de laboratorio en cámara de niebla salina. Se han empleado simultáneamente probetas testigo de acero con el fin de clasificar la corrosividad de las atmósferas, y se han estudiado las características medioambientales de las atmósferas donde se han llevado a cabo los ensayos. Mediante estos estudios se han obtenido las velocidades de corrosión y se han analizado en función de los parámetros ambientales.

MD simulation of atomic displacement cascades in Fe-10 at.%Cr binary alloy

International Nuclear Information System (INIS)

Tikhonchev, M.; Svetukhin, V.; Kadochkin, A.; Gaganidze, E.

2009-01-01

Molecular dynamics simulation of atomic displacement cascades up to 20 keV has been performed in Fe-10 at.%Cr binary alloy at a temperature of 600 K. The N-body interatomic potentials of Finnis-Sinclair type were used. According to the obtained results the dependence of 'surviving' defects amount is well approximated by power function that coincides with other researchers' results. Obtained cascade efficiency for damage energy in the range from 10 to 20 keV is ∼0.2 NRT that is slightly higher than for pure α-Fe. In post-cascade area Cr fraction in interstitials is in range 2-5% that is essentially lower than Cr content in the base alloy. The results on size and amount of vacancy and interstitial clusters generated in displacement cascades are obtained. For energies of 2 keV and higher the defect cluster average size increases and it is well approximated by a linear dependence on cascade energy both for interstitials and vacancies.

MD simulation of atomic displacement cascades in Fe-10 at.%Cr binary alloy

Energy Technology Data Exchange (ETDEWEB)

Tikhonchev, M., E-mail: tikhonchev@sv.ulsu.r [Ulyanovsk State University, Leo Tolstoy Str., 42, Ulyanovsk 432970 (Russian Federation); Joint Stock Company, ' State Scientific Center Research Institute of Atomic Reactors' , 433510 Dimitrovgrad-10 (Russian Federation); Svetukhin, V.; Kadochkin, A. [Ulyanovsk State University, Leo Tolstoy Str., 42, Ulyanovsk 432970 (Russian Federation); Gaganidze, E. [Forschungszentrum Karlsruhe, IMF II, 3640, D-76021 Karlsruhe (Germany)

2009-12-15

Molecular dynamics simulation of atomic displacement cascades up to 20 keV has been performed in Fe-10 at.%Cr binary alloy at a temperature of 600 K. The N-body interatomic potentials of Finnis-Sinclair type were used. According to the obtained results the dependence of 'surviving' defects amount is well approximated by power function that coincides with other researchers' results. Obtained cascade efficiency for damage energy in the range from 10 to 20 keV is approx0.2 NRT that is slightly higher than for pure alpha-Fe. In post-cascade area Cr fraction in interstitials is in range 2-5% that is essentially lower than Cr content in the base alloy. The results on size and amount of vacancy and interstitial clusters generated in displacement cascades are obtained. For energies of 2 keV and higher the defect cluster average size increases and it is well approximated by a linear dependence on cascade energy both for interstitials and vacancies.

19 CFR 10.454 - Regional value content.

Science.gov (United States)

2010-04-01

... TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. United States-Chile Free Trade Agreement Rules of Origin § 10.454 Regional value content. Where General Note 26, subdivision (n), HTSUS... 19 Customs Duties 1 2010-04-01 2010-04-01 false Regional value content. 10.454 Section 10.454...

Study of microstructure and magnetic properties of L10 FePt/SiO2 thin films

Directory of Open Access Journals (Sweden)

Giannopoulos G.

2014-07-01

Full Text Available Achieving magnetic recording densities in excess of 1Tbit/in2 requires not only perpendicular media with anisotropies larger than 7 MJ/m3, making FePt alloys an ideal choice, but also a narrow distribution below 10 nm for a reduced S/N ratio. Such grain size reduction and shape control are crucial parameters for high density magnetic recording, along with high thermal stability. Previous work has shown that the L10 FePt grain size can be controlled by alloying FePt with materials such as C, Ag, and insulators such as AlOx, MgO. Au and Al2O3 also act to segregate and magnetically decouple the FePt grains. Better results were obtained with C with respect to the uniformity of grains and SiO2 with respect to the shape. We present our results on co-sputtering FePt with C or SiO2 (up to 30 vol % on MgO (001 single crystal substrates at 350 and 500 oC. With C or SiO2 addition we achieved grain size reduction, shape control and isolated structure formation, producing continuous films with high uniformity and a narrow grain size distribution. These additions thus allow us to simultaneously control the coercivity and the S/N ratio. We also will report structural and microstructural properties.

Excited-State N2 Dissociation Pathway on Fe-Functionalized Au.

Science.gov (United States)

Martirez, John Mark P; Carter, Emily A

2017-03-29

Localized surface plasmon resonances (LSPRs) offer the possibility of light-activated chemical catalysis on surfaces of strongly plasmonic metal nanoparticles. This technology relies on lower-barrier bond formation and/or dissociation routes made available through energy transfer following the eventual decay of LSPRs. The coupling between these decay processes and a chemical trajectory (nuclear motion, charge-transfer, intersystem crossing, etc.) dictates the availability of these alternative (possibly lower barrier) excited-state channels. The Haber-Bosch method of NH 3 synthesis from N 2 and H 2 is notoriously energy intensive. This is due to the difficulty of N 2 dissociation despite the overall reaction being thermodynamically favorable at ambient temperatures and pressures. LSPRs may provide means to improve the kinetics of N 2 dissociation via induced resonance electronic excitation. In this work, we calculate, via embedded n-electron valence second-order perturbation theory within the density functional embedding theory, the excited-state potential energy surfaces for dissociation of N 2 on an Fe-doped Au(111) surface. This metal alloy may take advantage simultaneously of the strong LSPR of Au and the catalytic activity of Fe toward N 2 dissociation. We find the ground-state dissociation activation energy to be 4.74 eV/N 2 , with Fe as the active site on the surface. Consecutive resonance energy transfers (RETs) may be accessed due to the availability of many electronically excited states with intermediate energies arising from the metal surface that may couple to states induced by the Fe-dopant and the adsorbate molecule, and crossing between excited states may effectively lower the dissociation barrier to 1.33 eV. Our work illustrates that large energetic barriers, prohibitive toward chemical reaction, may be overcome through multiple RETs facilitating an otherwise difficult chemical process.

77 FR 15943 - United States-Korea Free Trade Agreement

Science.gov (United States)

2012-03-19

...-commercial or low-value importations. Section 10.1007 implements UKFTA Article 6.17 and Sec. 206 of the Act... Importer obligations. 10.1006 Certification not required. 10.1007 Maintenance of records. 10.1008 Effect of... CFR Parts 10, 24, 162, 163, and 178 [USCBP-2012-0007; CBP Dec. 12-03] RIN 1515-AD86 United States...

Superelasticity, corrosion resistance and biocompatibility of the Ti–19Zr–10Nb–1Fe alloy

Energy Technology Data Exchange (ETDEWEB)

Xue, Pengfei [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Key Laboratory of Aerospace Materials and Performance (Ministry of Education), Beihang University, Beijing 100191 (China); Li, Yan, E-mail: liyan@buaa.edu.cn [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Key Laboratory of Aerospace Materials and Performance (Ministry of Education), Beihang University, Beijing 100191 (China); Li, Kangming [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Key Laboratory of Aerospace Materials and Performance (Ministry of Education), Beihang University, Beijing 100191 (China); Zhang, Deyuan [Life Tech Scientific Corporation, Shenzhen 518057 (China); Zhou, Chungen [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China)

2015-05-01

Microstructure, mechanical properties, superelasticity and biocompatibility of a Ti–19Zr–10Nb–1Fe alloy are investigated. X-ray diffraction spectroscopy and transmission electron microscopy observations show that the as-cast Ti–19Zr–10Nb–1Fe alloy is composed of α′ and β phases, but only the β phase exists in the as-rolled and as-quenched alloys. The tensile stress–strain tests indicate that the as-quenched alloy exhibits a good combination of mechanical properties with a large elongation of 25%, a low Young's modulus of 59 GPa and a high ultimate tensile stress of 723 MPa. Superelastic recovery behavior is found in the as-quenched alloy during tensile tests, and the corresponding maximum of superelastic strain is 4.7% at the pre-strain of 6%. A superelastic recovery of 4% with high stability is achieved after 10 cyclic loading–unloading training processes. Potentiodynamic polarization and ion release measurements indicate that the as-quenched alloy shows a lower corrosion rate in Hank's solution and a much less ion release rate in 0.9% NaCl solution than those of the NiTi alloys. Cell culture results indicate that the osteoblasts' adhesion and proliferation are similar on both the Ti–19Zr–10Nb–1Fe and NiTi alloys. A better hemocompatibility is confirmed for the as-quenched Ti–19Zr–10Nb–1Fe alloy, attributed to more stable platelet adhesion and small activation degree, and a much lower hemolysis rate compared with the NiTi alloy. - Highlights: • A stable superelastic strain of 4.0% is achieved for the Ti–19Zr–10Nb–1Fe alloy. • The ion release rates of Ti–19Zr–10Nb–1Fe are much lower than that of Ni in NiTi. • Ti–19Zr–10Nb–1Fe has a similar cytocompatibility compared with the NiTi alloy. • Ti–19Zr–10Nb–1Fe exhibits a better hemocompatibility than the NiTi alloy.

Neutron capture resonances in 56Fe and 58Fe in the energy range from 10 to 100 keV

International Nuclear Information System (INIS)

Kaeppeler, F.; Wisshak, K.; Hong, L.D.

1982-11-01

The neutron capture cross section of 56 Fe and 58 Fe has been measured in the energy range from 10 to 250 keV relative to the gold standard. A pulsed 3 MV Van de Graaff accelerator and the 7 Li(p, n) reaction served as a neutron source. Capture gamma rays were detected by two C 6 D 6 detectors, which were operated in coincidence and anticoincidence mode. Two-dimensional data acquisition allowed to apply the pulse height weighting technique off-line. The samples were located at a flight path of 60 cm. The total time resolution was 1.2 ns thus allowing for an energy resolution of 2 ns/m. The experimental set-up was optimized with respect to low background and low neutron sensitivity. The additional flight path of 4 cm from the sample to the detector was sufficient to discriminate capture of sample scattered neutrons by the additional time of flight. In this way reliable results were obtained even for the strong s-wave resonances of both isotopes. The experimental capture yield was analyzed with the FANAC code. The energy resolution allowed to extract resonance parameters in the energy range from 10 to 100 keV. The individual systematic uncertainties of the experimental method are discussed in detail. They were found to range between 5 and 10% while the statistical uncertainty is 3-5% for most of the resonances. A comparison to the results of other authors exhibits in case of 56 Fe systematic differences of 7-11%. For 58 Fe the present results differ up to 50% from the only other measurement for this isotope. (orig.) [de

19 CFR 10.455 - Value of materials.

Science.gov (United States)

2010-04-01

... Chile or of the United States. (c) Accounting method. Any cost or value referenced in General Note 26(n... 19 Customs Duties 1 2010-04-01 2010-04-01 false Value of materials. 10.455 Section 10.455 Customs... of Origin § 10.455 Value of materials. (a) Calculating the regional value content. For purposes of...

(CaFeAs){sub 10}Pt{sub z}As{sub 8} superconductors and related compounds

Energy Technology Data Exchange (ETDEWEB)

Stuerzer, Tobias

2015-04-13

The main topic of this dissertation is the identification of new compounds, structure determination, and substitution dependent investigation of properties in this new branch of the family of iron arsenide superconductors (Chapter 2). Chapter 2.1 presents the identification of the superconducting compounds and the corresponding structure elucidation identifying two dif-ferent species (CaFeAs){sub 10}Pt{sub 3}As{sub 8} and (CaFeAs){sub 10}Pt{sub 4}As{sub 8} in this family (abbreviated as 1038 and 1048 according to their stoichiometry). However, a closer look revealed a more challenging structure chemistry which is covered in Chapter 2.2. The following two Chapters 2.3 and 2.4 are devoted to (CaFeAs){sub 10}Pt{sub 3}As{sub 8} and more detailed investigations on this parent compound of the new superconductor family. Furthermore, transition metal substitution series (CaFe{sub 1-x}M{sub x}As){sub 10}Pt{sub 3}As{sub 8} were synthesized to investigate the resemblance to model systems Ba(Fe{sub 1-x}M{sub x}){sub 2}As{sub x} and LaO(Fe{sub 1-x}M{sub x})As in the scope of structural changes and superconductivity as described in Chapter 2.5. Initially amazing differences in superconducting properties com-paring 1038 and 1048 compounds are analyzed in Chapter 2.6 establishing an universal dop-ing model in the (CaFe{sub 1-x}M{sub x}As){sub 10}Pt{sub z}As{sub 8} family. Additionally substituent dependent properties upon rare earth substitution in electron doped (Ca{sub 1-y}RE{sub y}FeAs){sub 10}Pt{sub 3}As{sub 8} are investigated in Chapter 2.7, while a detailed study of superconducting properties and magnetism in (Ca{sub 1-y}La{sub y}FeAs){sub 10}Pt{sub 3}As{sub 8} by the local μSR technique is presented in Chapter 2.8. In Chapter 2.9 a comparison of direct and electron doping is discussed based on codoping experiments in (Ca{sub 1-y}La{sub y}Fe{sub 1-x}Pt{sub x}As){sub 10}Pt{sub 3}As{sub 8} and (CaFe{sub 1-x}Pt{sub x}As){sub 10}Pt{sub 4}As{sub 8}. Finally, in Chapter 2.10

Nd Fe10 Mo2 alloys production through reduction-diffusion for nitrogenation

International Nuclear Information System (INIS)

Guilherme, Eneida da G.; Rechenberg, Hercilio R.

1996-01-01

In this work we have examined the effect of various processing variables on the Nd Fe 10 Mo 2 phase formation by reduction-diffusion calciothermic process (R D C). The best results were obtained for 4 hours treatment at 950 deg C with 40% excess content Nd Cl 3 and 50% excess content of Ca, for alloy Nd Fe 10.5 Mo 1.5 . Preliminary nitrogen absorption experiments have been done, without any further powder size reduction at temperatures between 300 and 350 deg C. (author)

Low-dimensional compounds containing cyanide groups. XXV. Synthesis, spectroscopic properties and crystal structures of two ionic iron(II) complexes with tricyanomethanide: tris(1,10-phenanthroline-κ(2)N,N')iron(II) bis(tricyanomethanide) and tris(2,2'-bipyridine-κ(2)N,N')iron(II) bis(tricyanomethanide) sesquihydrate.

Science.gov (United States)

Potočňák, Ivan; Váhovská, Lucia; Herich, Peter

2014-05-01

Two new diamagnetic coordination compounds, [Fe(phen)3][C(CN)3]2, (I), and [Fe(bpy)3][C(CN)3]2·1.5H2O, (II), have been synthesized and characterized by single-crystal X-ray diffraction analysis, and IR and UV-Vis spectroscopy (phen is 1,10-phenanthroline, C12H8N2, and bpy is 2,2'-bipyridine, C10H8N2). Both compounds are ionic with distorted octahedral [Fe(phen)3](2+) or [Fe(bpy)3](2+) complex cations, with average Fe-N distances of 1.977 (2) and 1.971 (3) Å, respectively, and two uncoordinated planar tricyanomethanide, or [C(CN)3](-), counter-anions balancing the positive charges of the cations. Solvent water molecules and tcm anions in (II) are linked via O-H...N hydrogen bonds into negatively charged layers and the interlayer space is filled by [Fe(bpy)3](2+) cations. The structures of (I) and (II) are stabilized by π-π interactions between the stacked aromatic rings of the phen ligands of two adjacent cations and by O-H...N hydrogen bonds, respectively, and also by π-π stacking interactions between phen and tcm units in (I).

Moessbauer study of the amorphous Pd70Fe10Si20 alloy upon transition to the crystalline state

International Nuclear Information System (INIS)

Sitek, J.; Prejsa, M.; Cirak, J.; Hucl, M.; Lipka, J.

1978-01-01

Foils of the amorphous alloy Pd 70 Fe 10 Si 20 were investigated after isothermal heating at the temperature range 350-450 0 C with a heating period from 15 min to 4 h. At 350 0 C no changes were observed in the shape of the Moessbauer spectra. At 400 0 C and at 450 0 C up to 30 min only the parameters of Moessbauer spectra consisting of two quadrupole doublets corresponding to palladium and silicon vicinities of iron atoms were changed. After further heating at 450 0 C crystalline phases of Pd 3 Fe and Fe 3 Si appeared on the Moessbauer spectra. (Auth.)

High magnetic ordering temperature in the perovskites Sr{sub 4-x}La{sub x}Fe{sub 3}ReO{sub 12} (x=0.0, 1.0, 2.0)

Energy Technology Data Exchange (ETDEWEB)

Retuerto, M.; Li, M.-R.; Go, Y.B. [Department of Chemistry and Chemical Biology, Rutgers, The State University of New Jersey, 610 Taylor Road, Piscataway, NJ 08854 (United States); Ignatov, A.; Croft, M. [Department of Physics and Astronomy, Rutgers, The State University of New Jersey, 136 Frelinghuysen Road, Piscataway, NJ 08854 (United States); Ramanujachary, K.V. [Department of Chemistry and Physics, Rowan University, 210 Mullica Hill Road, Glassboro, NJ 08028 (United States); Herber, R.H.; Nowik, I. [Racah Institute of Physics, Hebrew University, Jerusalem, 91904 Israel (Israel); Hodges, J.P. [Spallation Neutron Source, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Dachraoui, W.; Hadermann, J. [EMAT, University of Antwerp, Groenenborgerlaan 171, 2020 Antwerp (Belgium); Greenblatt, M., E-mail: martha@rutchem.rutgers.edu [Department of Chemistry and Chemical Biology, Rutgers, The State University of New Jersey, 610 Taylor Road, Piscataway, NJ 08854 (United States)

2012-10-15

A series of perovskites Sr{sub 4-x}La{sub x}Fe{sub 3}ReO{sub 12} (x=0.0, 1.0, 2.0) has been prepared by wet chemistry methods. The structure analyses by powder X-ray and neutron diffraction and electron microscopy show that these compounds adopt simple perovskite structures without cation ordering over the B sites: tetragonal (I4/mcm) for x=0.0 and 1.0 and orthorhombic (Pbmn) for x=2.0. The oxidation states of the cations in the compound with x=0.0 appear to be Fe{sup 3+/4+} and Re{sup 7+} and decrease for both with La substitution as evidenced by X-ray absorption spectroscopy. All the compounds are antiferromagnetically ordered above room temperature, as demonstrated by Moessbauer spectroscopy and the magnetic structures, which were determined by powder neutron diffraction. The substitution of Sr by La strongly affects the magnetic properties with an increase of T{sub N} up to {approx}750 K. - Graphical abstract: High resolution transmission electron microscopy image of Sr{sub 4-x}La{sub x}Fe{sub 3}ReO{sub 12} (x=2.0), showing twin domains. Fourier transforms are given of the areas indicated by the circles. Highlights: Black-Right-Pointing-Pointer Sr{sub 4-x}La{sub x}Fe{sub 3}ReO{sub 12} (x=0.0, 1.0, 2.0) perovskites prepared by wet chemistry. Black-Right-Pointing-Pointer PXD, PND, ED, indicate no cation ordering, I4/mcm) for x=0.0, 1.0, Pbmn for x=2. Black-Right-Pointing-Pointer XAS show oxidation states Fe{sup 3+/4+} and Re{sup 7+}; both decrease with increasing x. Black-Right-Pointing-Pointer All order antiferromagnetically above RT, with highest T{sub N} {approx}750 K.

ICORG 10-14

DEFF Research Database (Denmark)

Reynolds, J V; Preston, S R; O'Neill, B

2017-01-01

comprehensive modern staging, compares both these regimens. METHODS: This open label, multicentre, phase III RCT randomises patients (cT2-3, N0-3, M0) in a 1:1 fashion to receive CROSS protocol (Carboplatin and Paclitaxel with concurrent radiotherapy, 41.4Gy/23Fr, over 5 weeks). The power calculation is a 10......% difference in favour of CROSS, powered at 80%, two-sided alpha level of 0.05, requiring 540 patients to be evaluable, 594 to be recruited if a 10% dropout is included (297 in each group). The primary endpoint is overall survival, with a minimum 3-year follow up. Secondary endpoints include: disease free......). TRIAL REGISTRATION: NCT01726452 . Protocol 10-14. Date of registration 06/11/2012....

Exchange bias effect in L10-ordered FePt and FeCo-based bilayer structure: effect of increasing applied field

Science.gov (United States)

Singh, Sadhana; Kumar, Dileep; Bhagat, Babli; Choudhary, R. J.; Reddy, V. R.; Gupta, Ajay

2018-02-01

The applied magnetic field (H APP) dependence of the exchange bias (EB) is studied in an exchange-coupled thin-film bilayer composed of a hard ferromagnetic FePt layer in the proximity of a soft ferromagnetic FeCo layer. FePt/FeCo structure is deposited in an ultra-high vacuum chamber, where the FePt layer was first annealed at 823 K for 30 min and subsequently cooled to room temperature in the presence of an in-plane magnetic field, H MAX ~ 1.5 kOe to promote L10-ordered hard magnetic phase with magnetic moments aligned in one of the in-plane directions in the FePt layer. In-situ magneto-optical Kerr effect measurements during different stages of bilayer growth and detailed ex-situ superconducting quantum interference device-vibrating sample magnetometer measurements jointly revealed that due to the interplay between exchange coupling at the interface and dipolar energies of the saturated hard FePt layer, a hysteresis loop of FeCo layer shifts along the magnetic field axis. A clear dependence of EB field (H EB) on increasing maximum value of the H APP during the hysteresis loop measurement is understood in terms of the magnetic state of soft and hard magnetic layers, where EB increases with increasing H APP until the hard layer moment remains undisturbed in its remanence state. As soon as the field was sufficient to rotate the spins of the FePt layer, the loop became symmetric with respect to the field axis.

High Field Linear Magnetoresistance Sensors with Perpendicular Anisotropy L10-FePt Reference Layer

Directory of Open Access Journals (Sweden)

X. Liu

2016-01-01

Full Text Available High field linear magnetoresistance is an important feature for magnetic sensors applied in magnetic levitating train and high field positioning measurements. Here, we investigate linear magnetoresistance in Pt/FePt/ZnO/Fe/Pt multilayer magnetic sensor, where FePt and Fe ferromagnetic layers exhibit out-of-plane and in-plane magnetic anisotropy, respectively. Perpendicular anisotropy L10-FePt reference layer with large coercivity and high squareness ratio was obtained by in situ substrate heating. Linear magnetoresistance is observed in this sensor in a large range between +5 kOe and −5 kOe with the current parallel to the film plane. This L10-FePt based sensor is significant for the expansion of linear range and the simplification of preparation for future high field magnetic sensors.

Ostwald Ripening Process of Coherent β′ Precipitates during Aging in Fe0.75Ni0.10Al0.15 and Fe0.74Ni0.10Al0.15Cr0.01 Alloys

Directory of Open Access Journals (Sweden)

N. Cayetano-Castro

2015-01-01

Full Text Available The Ostwald ripening process was studied in Fe0.75Ni0.10Al0.15 and Fe0.74Ni0.10Al0.15Cr0.01 alloys after aging at 750, 850, and 950°C for different times. The microstructural evolution shows a rounded cube morphology (Fe, NiAl β′ precipitates aligned in the ferrite matrix, which changes to elongated plates after prolonged aging. The variation of the equivalent radii of precipitates with time follows the modified Lifshitz-Slyozov-Wagner theory for diffusion-controlled coarsening. Thermo-Calc analysis shows that the chromium content is richer in the matrix than in the precipitates which causes higher hardness and coarsening resistance in the aged Fe0.74Ni0.10Al0.15Cr0.01 alloy.

Magnetic Circular X-ray Dichroism Study of Paramagnetic and Anti-Ferromagnetic States in SrFeO3 Using a 10-T Superconducting Magnet

International Nuclear Information System (INIS)

Okamoto, J.; Mamiya, K.; Fujimori, S.-I.; Okane, T.; Saitoh, Y.; Muramatsu, Y.; Fujimori, A.; Ishiwata, S.; Takano, M.

2004-01-01

Magnetic circular x-ray dichroism (MCXD) measurements in Fe 2p absorption have been done on SrFeO3, which shows a spiral anti-ferromagnetism, by using a 10-T superconducting magnet. Finite MCXD structures have been observed under magnetic field of 8 T even in the paramagnetic and anti-ferromagnetic states. The intensity of the MCXD structure at hv ∼ 710 eV increases linearly as magnetic field increases linearly and the total magnetic moments estimated by MCXD sum rules roughly corresponds to the magnetization measured by SQUID measurements. MCXD study of paramagnetic and/or anti-ferromagnetic samples can be done by using a superconducting magnet that generates a strong magnetic field enough to induce finite magnetization

An Efficiency Comparison of MBA Programs: Top 10 versus Non-Top 10

Science.gov (United States)

Hsu, Maxwell K.; James, Marcia L.; Chao, Gary H.

2009-01-01

The authors compared the cohort group of the top-10 MBA programs in the United States with their lower-ranking counterparts on their value-added efficiency. The findings reveal that the top-10 MBA programs in the United States are associated with statistically higher average "technical and scale efficiency" and "scale efficiency", but not with a…

Effect of hydrogen on Ti-10V-2Fe-3Al

International Nuclear Information System (INIS)

Costa, J.E.

1985-01-01

The effect of hydrogen on the physical and mechanical properties of the metastable β alloy Ti-10V-2Fe-3Al was examined. This study had three main goals. The first was to improve the understanding of the effects of hydrogen in the β phase. The second goal was to determine the effects of hydrogen on the specific alloy Ti-10V-2Fe-3Al. The third goal was to identify possible in-service problems that could occur in Ti-10V-2Fe-3Al and in similar alloys. The effects of hydrogen were examined in three different microstructures: beta-annealed and water-quenched (B/WQ), beta-annealed and furnace cooled (B/FC), and solution treated and aged (STA). The B/WQ microstructure was nominally all-β with some athermal omega phase while the B/FC and STA microstructures were α + β microstructures. Hydrogen concentrations from approx.0 to >30 at.% were used. Hydrogen was introduced into test specimens using either Sieverts charging or cathodic charging techniques. When the B/WQ microstructure was deformed, the β phase was transformed to orthorhombic α'' martensite. Hydrogen effects in the B/FC and STA microstructures were largely the result of hydride formation at α/β interfaces. The effect of hydride formation was observed as decreases in the reduction of area for tensile specimens

Iron-platinum multilayer thin film reactions to form L1(0) iron-platinum and exchange spring magnets

Science.gov (United States)

Yao, Bo

FePt films with the L10 phase have potential applications for magnetic recording and permanent magnets due to its high magnetocrystalline anisotropy energy density. Heat treatment of [Fe/Pt] n multilayer films is one approach to form the L10 FePt phase through a solid state reaction. This thesis has studied the diffusion and reaction of [Fe/Pt]n multilayer films to form the L10 FePt phase and has used this understanding to construct exchange spring magnets. The process-structure-property relations of [Fe/Pt] n multilayer films were systematically examined. The transmission electron microscopy (TEM) study of the annealed multilayers indicates that the Pt layer grows at the expense of Fe during annealing, forming a disordered fcc FePt phase by the interdiffusion of Fe into Pt. This thickening of the fcc Pt layer can be attributed to the higher solubilities of Fe into fcc Pt, as compared to the converse. For the range of film thickness studied, a continuous L10 FePt product layer that then thickens with further annealing is not found. Instead, the initial L10 FePt grains are distributed mainly on the grain boundaries within the fcc FePt layer and at the Fe/Pt interfaces and further transformation of the sample to the ordered L10 FePt phase proceeds coupled with the growth of the initial L10 FePt grains. A comprehensive study of annealed [Fe/Pt]n films is provided concerning the phase fraction, grain size, nucleation/grain density, interdiffusivity, long-range order parameter, and texture, as well as magnetic properties. A method based on hollow cone dark field TEM is introduced to measure the volume fraction, grain size, and density of ordered L10 FePt phase grains in the annealed films, and low-angle X-ray diffraction is used to measure the effective Fe-Pt interdiffusivity. The process-structure-properties relations of two groups of samples with varying substrate temperature and periodicity are reported. The results demonstrate that the processing parameters

Microstructure, tensile deformation mode and crevice corrosion resistance in Ti-10Mo-xFe alloys

International Nuclear Information System (INIS)

Min, X.H.; Emura, S.; Nishimura, T.; Tsuchiya, K.; Tsuzaki, K.

2010-01-01

The microstructure, the tensile deformation mode at ambient temperature and the crevice corrosion resistance at a high temperature of 373 K were investigated in the Ti-10Mo-xFe (x = 0, 1, 3, 5) alloys. The stability of the β phase increased, and the formation of the α'' martensite and the athermal ω phase was suppressed by the increase in the Fe content. EPMA examinations indicated that the existence of the α'' martensite in the Ti-10Mo alloy was caused by the solidification segregation of Mo atoms. EBSD observations showed that the deformation mode changed from a {3 3 2} twinning to a slip by an increase in the Fe content, which coincided with the prediction by the electron/atom (e/a) ratio. The Ti-10Mo-3Fe alloy showed the highest yield strength of 935 MPa among all the alloys, while the Ti-10Mo-1Fe alloy showed the lowest value of 563 MPa due to the change in the deformation mode. On the other hand, all the alloys exhibited a high crevice corrosion resistance in a high chloride and high acidic solution at the high temperature, although the corrosion resistance decreased with an increase in the Fe content. The decrease in the corrosion resistance can be explained by the bond order (Bo). A good combination of tensile properties and crevice corrosion resistance may be obtainable through a further optimization of the Fe content by the e/a ratio and the Bo.

Structural and magnetic evolution of nanostructured Co{sub 40}Fe{sub 10}Zr{sub 10}B{sub 40} prepared by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Raanaei, Hossein, E-mail: hraanaei@yahoo.com [Department of Physics, Persian Gulf University, Bushehr 75169 (Iran, Islamic Republic of); Abbasi, Sadeq [Department of Physics, Persian Gulf University, Bushehr 75169 (Iran, Islamic Republic of); Behaein, Saeed [Department of Physics, Shiraz University, Shiraz 71454 (Iran, Islamic Republic of)

2015-06-15

The structural and magnetic properties of nanocrystalline alloy powder Co{sub 40}Fe{sub 10}Zr{sub 10}B{sub 40} prepared by mechanical alloying have been characterized by using X-ray diffraction (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and differential scanning calorimeter (DSC). It is shown that the crystallite size has been decreased significantly to about 15 nm after 8 h milling time. On continuing the milling time mechanical crystallization and subsequently the alloying process were noticed up to 190 h. Saturation magnetization decreased during the whole process while coercivity achieved the highest value at the crystallization stage. Post treatment of milled powder at 190 h revealed crystalline constituent elements. - Highlights: • This article focuses on mechanical alloying of Co{sub 40}Fe{sub 10}Zr{sub 10}B{sub 40} system. • Mechanical crystallization is observed. • Structural and magnetic properties were investigated. • The heat treatment revealed the crystalline phases of constituent elements.

Nd Fe{sub 10} Mo{sub 2} alloys production through reduction-diffusion for nitrogenation; Obtencao de ligas NdFe{sub 10}Mo{sub 2} por reducao-difusao para posterior nitrogenacao

Energy Technology Data Exchange (ETDEWEB)

Guilherme, Eneida da G. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil); Rechenberg, Hercilio R. [Sao Paulo Univ., SP (Brazil). Inst. de Fisica

1996-12-31

In this work we have examined the effect of various processing variables on the Nd Fe{sub 10} Mo{sub 2} phase formation by reduction-diffusion calciothermic process (R D C). The best results were obtained for 4 hours treatment at 950 deg C with 40% excess content Nd Cl{sub 3} and 50% excess content of Ca, for alloy Nd Fe{sub 10.5} Mo{sub 1.5}. Preliminary nitrogen absorption experiments have been done, without any further powder size reduction at temperatures between 300 and 350 deg C. (author) 9 refs., 6 figs., 1 tab.

50 CFR Table 5 (south) to Part 660... - 2009-2010 Trip Limits for Open Access Gears South of 40°10′ N. Lat.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false 2009-2010 Trip Limits for Open Access Gears South of 40°10â² N. Lat. 5 Table 5 (South) to Part 660, Subpart G Wildlife and Fisheries FISHERY... Trip Limits for Open Access Gears South of 40°10′ N. Lat. Link to an amendment published at 75 FR 60995...

50 CFR Table 5 (north) to Part 660... - 2009-2010 Trip Limits for Open Access Gears North of 40°10′ N. Lat.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false 2009-2010 Trip Limits for Open Access Gears North of 40°10â² N. Lat. 5 Table 5 (North) to Part 660, Subpart G Wildlife and Fisheries FISHERY... Trip Limits for Open Access Gears North of 40°10′ N. Lat. Link to an amendment published at 75 FR 60995...

First principles calculations of the magnetic and hyperfine properties of Fe/N/Fe and Fe/O/Fe multilayers in the ground state of cohesive energy

Science.gov (United States)

dos Santos, A. V.; Samudio Pérez, C. A.; Muenchen, D.; Anibele, T. P.

2015-01-01

The ground state properties of Fe/N/Fe and Fe/O/Fe multilayers were investigated using the first principles calculations. The calculations were performed using the Linearized Augmented Plane Wave (LAPW) method implemented in the Wien2k code. A supercell consisting of one layer of nitride (or oxide) between two layers of Fe in the bcc structure was used to model the structure of the multilayer. The research in new materials also stimulated theoretical and experimental studies of iron-based nitrides due to their variety of structural and magnetic properties for the potential applications as in high strength steels and for high corrosion resistance. It is obvious from many reports that magnetic iron nitrides such as γ-Fe4N and α-Fe16N2 have interesting magnetic properties, among these a high magnetisation saturation and a high density crimp. However, although Fe-N films and multilayers have many potential applications, they can be produced in many ways and are being extensively studied from the theoretical point of view there is no detailed knowledge of their electronic structure. Clearly, efforts to understand the influence of the nitrogen atoms on the entire electronic structure are needed as to correctly interpret the observed changes in the magnetic properties when going from Fe-N bulk compounds to multilayer structures. Nevertheless, the N atoms are not solely responsible for electronics alterations in solid compounds. Theoretical results showed that Fe4X bulk compounds, where X is a variable atom with increasing atomic number (Z), the nature of bonding between X and adjacent Fe atoms changes from more covalent to more ionic and the magnetic moments of Fe also increase for Z=7, i.e. N. This is an indicative that atoms with a Z number higher than 7, i.e., O, can produce several new alterations in the entire magnetic properties of Fe multilayers. This paper presents the first results of an ab-initio electronic structure calculations, performed for Fe-N and Fe

39 CFR 111.3 - Amendments to the Mailing Standards of the United States Postal Service, Domestic Mail Manual.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Amendments to the Mailing Standards of the United.... 39 June 16, 1991 56 FR 56015 40 September 15, 1991 56 FR 56013 41 December 15, 1991 57 FR 21611 42... July 1, 1997 62 FR 30457 53 January 1, 1998 62 FR 63851 54 January 10, 1999 64 FR 39 55 January 10...

10 CFR 20.1005 - Units of radioactivity.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Units of radioactivity. 20.1005 Section 20.1005 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION General Provisions § 20.1005 Units of radioactivity. For the purposes of this part, activity is expressed in the special unit of...

Metallic oxide nano-clusters synthesis by ion implantation in high purity Fe10Cr alloy

International Nuclear Information System (INIS)

Zheng, Ce

2015-01-01

ODS (Oxide Dispersed Strengthened) steels, which are reinforced with metal dispersions of nano-oxides (based on Y, Ti and O elements), are promising materials for future nuclear reactors. The detailed understanding of the mechanisms involved in the precipitation of these nano-oxides would improve manufacturing and mechanical properties of these ODS steels, with a strong economic impact for their industrialization. To experimentally study these mechanisms, an analytical approach by ion implantation is used, to control various parameters of synthesis of these precipitates as the temperature and concentration. This study demonstrated the feasibility of this method and concerned the behaviour of alloys models (based on aluminium oxide) under thermal annealing. High purity Fe-10Cr alloys were implanted with Al and O ions at room temperature. Transmission electron microscopy observations showed that the nano-oxides appear in the Fe-10Cr matrix upon ion implantation at room temperature without subsequent annealing. The mobility of implanted elements is caused by the defects created during ion implantation, allowing the nucleation of these nanoparticles, of a few nm in diameter. These nanoparticles are composed of aluminium and oxygen, and also chromium. The high-resolution experiments show that their crystallographic structure is that of a non-equilibrium compound of aluminium oxide (cubic γ-Al 2 O 3 type). The heat treatment performed after implantation induces the growth of the nano-sized oxides, and a phase change that tends to balance to the equilibrium structure (hexagonal α-Al 2 O 3 type). These results on model alloys are fully applicable to industrial materials: indeed ion implantation reproduces the conditions of milling and heat treatments are at equivalent temperatures to those of thermo-mechanical treatments. A mechanism involving the precipitation of nano-oxide dispersed in ODS alloys is proposed in this manuscript based on the obtained experimental results

A 10 nN resolution thrust-stand for micro-propulsion devices

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, Subha; Courtney, Daniel G.; Shea, Herbert, E-mail: herbert.shea@epfl.ch [Microsystems for Space Technologies Laboratory (LMTS), Ecole Polytechnique Federale de Lausanne (EPFL), Neuchatel (Switzerland)

2015-11-15

We report on the development of a nano-Newton thrust-stand that can measure up to 100 μN thrust from different types of microthrusters with 10 nN resolution. The compact thrust-stand measures the impingement force of the particles emitted from a microthruster onto a suspended plate of size 45 mm × 45 mm and with a natural frequency over 50 Hz. Using a homodyne (lock-in) readout provides strong immunity to facility vibrations, which historically has been a major challenge for nano-Newton thrust-stands. A cold-gas thruster generating up to 50 μN thrust in air was first used to validate the thrust-stand. Better than 10 nN resolution and a minimum detectable thrust of 10 nN were achieved. Thrust from a miniature electrospray propulsion system generating up to 3 μN of thrust was measured with our thrust-stand in vacuum, and the thrust was compared with that computed from beam diagnostics, obtaining agreement within 50 nN to 150 nN. The 10 nN resolution obtained from this thrust-stand matches that from state-of-the-art nano-Newton thrust-stands, which measure thrust directly from the thruster by mounting it on a moving arm (but whose natural frequency is well below 1 Hz). The thrust-stand is the first of its kind to demonstrate less than 3 μN resolution by measuring the impingement force, making it capable of measuring thrust from different types of microthrusters, with the potential of easy upscaling for thrust measurement at much higher levels, simply by replacing the force sensor with other force sensors.

Crystal structure of tris(1,10-phenanthroline-κ2N,N′iron(II bis[bis(trifluoromethylsulfonylimide] monohydrate

Directory of Open Access Journals (Sweden)

Kazunori Teramoto

2015-01-01

Full Text Available The crystal structure of the title complex, [Fe(C12H8N23][(CF3SO22N]2·H2O, is constructed by one octahedral [Fe(phen3]2+ (phen = 1,10-phenanthroline cation (point group symmetry 2, two Tf2N− [bis(trifluoromethylsulfonylimide] anions, and one water molecule of crystallization (point group 2. The Fe—N bond lengths are indicative of a d6 low-spin state for the FeII ion in the complex. The dihedral angle between the phen ligands in the cation is 87.64 (6°. The Tf2N− counter-anion is non-coordinating, with the –CF3 groups arranged in a trans fashion with respect to each other, leading to an anti,anti conformation of the –CF3 groups and –SO2N– moieties relative to the S—C bonds. The water molecule of crystallization connects two O atoms of the Tf2N− anions through weak hydrogen bonds. C—H...O hydrogen-bonding interactions are also observed, consolidating the packing of the molecules into a three-dimensional network structure.

Structural evolutions of the mechanically alloyed Al70Cu20Fe10 ...

Indian Academy of Sciences (India)

The i-phase was observed only for short-time milled powders after heat treatment above 600°C. The -phase was one of the major phases in the Al70Cu20Fe10 alloy. The w-Al7Cu2Fe1 phase (w-phase) was obtained only after heat treatment of the short-time milled and unmilled samples. The present investigation ...

Synthesis NiAl1,0Fe1,0O4 catalyst by the combustion reaction to their use in the shift reaction (WGSR)

International Nuclear Information System (INIS)

Santos, P.T.A.; Costa, A.C.F.M.; Neiva, L.S.; Gama, L.; Argolo, F.; Andrade, H.M.C.

2009-01-01

This work aims at the synthesis of catalyst NiAl 1,0 Fe 1,0 O 4 by combustion reaction using urea as fuel, to evaluate its performance in the production of hydrogen by the reaction of displacement of water vapor (WGSR). The initial composition of the solution was based on valencia total oxidizing and reducing reagents based on the concepts of the chemistry of propellants, using container as a crucible of glassy silica. The resulting powder was characterized by X-ray diffraction, infrared spectroscopy, nitrogen adsorption isotherms (BET), scanning electronic microscope and catalytic tests. The DRX results reveal the presents majoritary phase NiAl 1,0 Fe 1,0 O 4 spinel, the catalyst presents surface area 28 m 2 /g and isotherms type III. Higher conversion CO/CO 2 of 75% CO conversion observed at 500 deg C and catalytic activity of 43 mmolg -1 .h -1 at 450 deg C. (author)

Differential coincidence circuit in the 10-10 second region (1960)

International Nuclear Information System (INIS)

Van Zurk, R.; Grenoble-1 Univ., 38; Commissariat a l'Energie Atomique, Saclay

1960-01-01

A coincidence circuit of low resolution time using the differential coincidence Bay principle is described. It uses three 6BN6 tubes ordered to chronotron structure. Results with Radiotechnique 56 AVP photomultipliers and for 60 Co γ-γ coincidences are 4,6.10 -10 s (full width at half maximum) if the efficiency is ε = 40 per cent and also 7,2.10 -10 s if ε = 85 per cent. (author) [fr

46 CFR 161.002-10 - Automatic fire detecting system control unit.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Automatic fire detecting system control unit. 161.002-10...-10 Automatic fire detecting system control unit. (a) General. The fire detecting system control unit... and the battery to be charged. (h) Automatic fire detecting system, battery charging and control—(1...

Preparation of c-axis perpendicularly oriented ultra-thin L10-FePt films on MgO and VN underlayers

Science.gov (United States)

Futamoto, Masaaki; Shimizu, Tomoki; Ohtake, Mitsuru

2018-05-01

Ultra-thin L10-FePt films of 2 nm average thickness are prepared on (001) oriented MgO and VN underlayers epitaxially grown on base substrate of SrTiO3(001) single crystal. Detailed cross-sectional structures are observed by high-resolution transmission electron microscopy. Continuous L10-FePt(001) thin films with very flat surface are prepared on VN(001) underlayer whereas the films prepared on MgO(001) underlayer consist of isolated L10-FePt(001) crystal islands. Presence of misfit dislocation and lattice bending in L10-FePt material is reducing the effective lattice mismatch with respect to the underlayer to be less than 0.5 %. Formation of very flat and continuous FePt layer on VN underlayer is due to the large surface energy of VN material where de-wetting of FePt material at high temperature annealing process is suppressed under a force balance between the surface and interface energies of FePt and VN materials. An employment of underlayer or substrate material with the lattice constant and the surface energy larger than those of L10-FePt is important for the preparation of very thin FePt epitaxial thin continuous film with the c-axis controlled to be perpendicular to the substrate surface.

DFT calculations of the charged states of N@C60 and Fe4 single molecule magnets investigated in tunneling spectroscopy

Science.gov (United States)

Nossa, Javier; Islam, Fhokrul; Canali, Carlo; Pederson, Mark

2012-02-01

For device applications of single molecule magnets (SMMs) in high-density information storage and quantum-state control it is essential that the magnetic properties of the molecules remain stable under the influence of metallic contacts or surface environment. Recent tunneling experiments [1, 2] on N@C60 and Fe4 SMM have shown that these molecules preserve their magnetic characteristics when they are used as the central island of single-electron transistors. Although quantum spin models have been used extensively to study theoretically tunneling spectroscopy of SMMs, it has been shown recently that the orbital degrees of freedom, which is absent in spin models, can significantly affect the tunneling conductance [3]. In this work we present first-principles calculations of the neutral and charged states of N@C60 and Fe4 SMMs, and discuss a strategy to include their properties into a theory of quantum transport. We also present results of the magnetic anisotropy for the different charge states of Fe4 and discuss their relevance for experiments [2] in the sequential tunneling and cotunnelling regimes. [4pt] [1]. N. Roch et al., Phys. Rev. B 83, 081407 (2011). [0pt] [2]. A.S. Zyazin et al., Nano Lett. 10, 3307 (2010). [0pt] [3]. L. Michalak et al., Phys. Rev. Lett. 104, 017202 (2010).

Communication of 10 January 2008 received from the Permanent Mission of the United Kingdom regarding the Export of Nuclear Material and of Certain Categories of Equipment and Other Material

International Nuclear Information System (INIS)

2008-01-01

The Director General has received a note ver bale from the Permanent Mission of the United Kingdom, dated 10 January 2008, in which it requests that the Agency circulate to all Member States a letter of 12 December 2006 from the Chairman of the Zangger Committee, Mr. Pavel Klucky, to the Director General, on behalf of the Governments of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, China, Croatia, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, Republic of Korea, Luxemburg, the Netherlands, Norway, Poland, Portugal, Romania, Russian Federation, Slovakia, Slovenia, South Africa, Spain, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland and the United States of America, concerning the export of nuclear material and of certain categories of equipment and other material [fr

Semipolar MOVPE AlGaN on (10 anti 10) m-plane sapphire; MOVPE von semipolarem AlGaN auf (10 anti 10) m-plane Saphir

Energy Technology Data Exchange (ETDEWEB)

Mehnke, Frank; Stellmach, Joachim; Frentrup, Martin; Kusch, Gunnar; Wernicke, Tim; Pristovsek, Markus; Kneissl, Michael [Technische Universitaet Berlin, Institut fuer Festkoerperphysik, Hardenbergstr. 36, 10623 Berlin (Germany)

2011-07-01

The energy gap of AlGaN varies between 3.4 eV and 6.2 eV and allows light emitting diodes (LED) in the ultraviolet spectral region. The authors studied semipolar (11 anti 22) AlGaN layers that were deposited on (10 anti 10) m-plane sapphire using MOVPE (metalorganic vapor phase epitaxy) without nucleation layer with a substrate temperature below 1100 C in H2 atmosphere. The layers are preferably (11 anti 22) oriented. The sample show a surface roughness between 15 and 2 nm. The Al content of the smoothest samples is about 60% determined by transmission experiments. Below 60% Al content a triangular morphology was observed, the opening angle increased with decreasing Al content. The absorption edge was 0.05 eV (GaN) to 0.35 eV (AlN) below the band edge of (0001) oriented AlGaN layers. Further investigations of semipolar AlGaN layers to study the applicability for UV LEDs are under preparation.

Spin-dependent electronic transport characteristics in Fe4N/BiFeO3/Fe4N perpendicular magnetic tunnel junctions

Science.gov (United States)

Yin, Li; Wang, Xiaocha; Mi, Wenbo

2018-01-01

Perpendicular magnetic tunnel junctions (MTJs) have attracted increasing attention owing to the low energy consumption and wide application prospects. Herewith, against Julliere's formula, an inverse tunnel magnetoresistance (TMR) appears in tetragonal Fe4N/BiFeO3/Fe4N perpendicular MTJs, which is attributed to the binding between the interface resonant tunneling state and central (bordered) hot spots. Especially, antiferromagnetic BiFeO3 shows an extra spin-polarized resonant state in the barrier, which provides a magnetic-barrier factor to affect the tunneling transport in MTJs. Meanwhile, due to the spin-polarized transport in Fe4N/BiFeO3/Fe4N MTJs, the sign of TMR can be tuned by the applied bias. The tunable TMR and resonant magnetic barrier effect pave the way for clarifying the tunneling transport in other junctions and spintronic devices.

Waste Area Group 10, Operable Unit 10-08, Remedial Investigation/Feasibility Study Annual Status Report for Fiscal Year 2006

Energy Technology Data Exchange (ETDEWEB)

R. P. Wells

2007-05-09

This report provides a status of the progress made in Fiscal Year 2006 on tasks identified in the Waste Area Group 10, Operable Unit 10-08, Remedial Investigation/Feasibility Study Work Plan. Major accomplishments include: (1) groundwater sampling and review of the groundwater monitoring data, (2) installation of a Sitewide groundwater-level monitoring network, (3) update of the Groundwater Monitoring and Field Sampling Plan of Operable Unit 10-08, (4) re-evaluation of the risk at Site TSF-08, (5) progress on the Operable Unit 10-08 Sitewide Groundwater Model.

Structural, thermal, spectroscopic and magnetic studies of the (C2N2H10)0.5[Fe xV1-x(HPO3)2] (x = 0.26, 0.52, 0.74) solid solution

International Nuclear Information System (INIS)

Cisneros, Jose L.; Fernandez-Armas, Sergio; Mesa, Jose L.; Pizarro, Jose L.; Arriortua, Maria I.; Rojo, Teofilo

2006-01-01

The (C 2 N 2 H 10 ) 0.5 [Fe x V 1-x (HPO 3 ) 2 ] (x = 0.26, 0.52 0.74) compounds have been obtained by mild solvothermal conditions in the form of micro-crystalline powder with brown color. The crystal structures were refined by X-ray powder diffraction data using the Rietveld method. The compounds crystallize in the monoclinic system, space group P2/c with the unit-cell parameters, a = 9.262(5) A, b = 8.823(5) A, c = 9.714(6) A, β = 120.84(3) o ; a = 9.245(1) A, b = 8.823(1) A, c = 9.698(1)A, β = 120.80(1) o and, a = 9.254(4)A, b = 8.822(4)A, c = 9.702(4)A, β = 120.73(3) o for (C 2 N 2 H 10 ) 0.5 [Fe 0.26 V 0.74 (HPO 3 ) 2 ] (1) (C 2 N 2 H 10 ) 0.5 [Fe 0.52 V 0.48 (HPO 3 ) 2 ] (2), and (C 2 N 2 H 10 ) 0.5 [Fe 0.74 V 0.26 (HPO 3 ) 2 ] (3). The compounds show an open crystalline structure with three-dimensional character, whose formula for the anionic inorganic skeleton is [M(HPO 3 ) 2 ] 2- . The inorganic framework is formed by [MO 6 ] octahedra inter-connected by phosphite groups. The structure of the compounds exhibits channels extended along the [1 0 0] and [0 0 1] directions and the ethylendiammonium cations are located inside these channels, linked through hydrogen bonds and ionic interactions. The infrared spectra show the bands corresponding to the stretching (P-H) vibration of the phosphite group and the band corresponding to the deformation mode of the ethylendiammonium cation, δ(NH 3 + ). The thermal and thermodiffractometric behavior show that the compounds are stable up to approximately 300 deg. C, at higher temperatures the decomposition of the crystal structure by calcination of the organic cation starts. The diffuse reflectance spectra show bands of the V 3+ ion (d 2 ), and a band of the Fe 3+ ion (d 5 ), in a slightly distorted octahedral symmetry. The values of the Dq and Racah parameters (B and C) have been calculated for the V(III) cation. Magnetic measurements were performed on a powdered sample from 5 to 300 K at magnetic fields 1000, 500

FORC-study of magnetization reversal of L10-FePt based exchange coupled composite films

Directory of Open Access Journals (Sweden)

Gongyuan Situ

2017-05-01

Full Text Available Perpendicular exchange coupled composite structures were prepared, utilizing L10-FePt as hard layer and [Co/Ni]N multilayer as soft layer. Magnetic characteristics revealed the gradually change of the magnetization reversal mechanism from incoherent rotational mode to dominant wall motion as the thickness of soft layer increases. Furthermore, FORC analysis were employed to characterize the interactions of our ECC magnetic system, the result indicates that the exchange coupling interaction were enhanced with the increasing thickness of soft layer.

Lattice sites, charge states and spin–lattice relaxation of Fe ions in "5"7Mn"+ implanted GaN and AlN

International Nuclear Information System (INIS)

Masenda, H.; Naidoo, D.; Bharuth-Ram, K.; Gunnlaugsson, H.P.; Johnston, K.; Mantovan, R.; Mølholt, T.E.; Ncube, M.; Shayestehaminzadeh, S.; Gíslason, H.P.; Langouche, G.; Ólafsson, S.; Weyer, G.

2016-01-01

The lattice sites, valence states, resulting magnetic behaviour and spin–lattice relaxation of Fe ions in GaN and AlN were investigated by emission Mössbauer spectroscopy following the implantation of radioactive "5"7Mn"+ ions at ISOLDE/CERN. Angle dependent measurements performed at room temperature on the 14.4 keV γ-rays from the "5"7Fe Mössbauer state (populated from the "5"7Mn β"− decay) reveal that the majority of the Fe ions are in the 2+ valence state nearly substituting the Ga and Al cations, and/or associated with vacancy type defects. Emission Mössbauer spectroscopy experiments conducted over a temperature range of 100–800 K show the presence of magnetically split sextets in the “wings” of the spectra for both materials. The temperature dependence of the sextets relates these spectral features to paramagnetic Fe"3"+ with rather slow spin–lattice relaxation rates which follow a T"2 temperature dependence characteristic of a two-phonon Raman process. - Highlights: • The majority of the Fe ions are in the 2+ state, located on near substitutional sites associated with vacancy type defects. • A significant fraction of the Fe ions are in the paramagnetic Fe"3"+ state. • Spin–lattice relaxation of Fe"3"+ in both GaN and AlN follows a two-phonon Raman process.

Stopping power of charged particles from 10 eV/amu to 10 GeV/amu

International Nuclear Information System (INIS)

Nakane, Yoshihiro; Tanaka, Shun-ichi; Furihata, Shiori; Iwai, Satoshi.

1993-08-01

Electric collision, nuclear collision and total stopping powers in 10 kinds of elements: H 2 , He, Be, C, Al, Fe, Cu, W, Pb and U, and 4 kinds of materials: water, phantom, LiF-TLD and SSNTD (solid state neutron track detector) have been calculated for 10 kinds of charged particles from 10 eV/amu to 10 GeV/amu with STOPPING, SPAR, and RSTAN/RSHEV codes, in which the charged particles are important projectiles for evaluating the dose and detector responses of radiations, and for accelerator shielding calculations. Calculated data are presented in Table and Figure. (author)

Comparative Efficacy of Feline Leukemia Virus (FeLV) Inactivated Whole-Virus Vaccine and Canarypox Virus-Vectored Vaccine during Virulent FeLV Challenge and Immunosuppression.

Science.gov (United States)

Patel, M; Carritt, K; Lane, J; Jayappa, H; Stahl, M; Bourgeois, M

2015-07-01

Four vaccines for feline leukemia virus (FeLV) are available in the United States. This study's purpose was to compare the efficacy of Nobivac feline 2-FeLV (an inactivated, adjuvanted whole-virus vaccine) and PureVax recombinant FeLV (a live, canarypox virus-vectored vaccine) following FeLV challenge. Cats were vaccinated at 9 and 12 weeks with Nobivac feline 2-FeLV (group A, n = 11) or PureVax recombinant FeLV (group B, n = 10). Group C (n = 11) comprised unvaccinated controls. At 3 months postvaccination, cats were immunosuppressed and challenged with FeLV-A/61E. The outcomes measured were persistent antigenemia at 12 weeks postchallenge (PC) and proviral DNA and viral RNA at 3 to 9 weeks PC. Persistent antigenemia was observed in 0 of 11 cats in group A, 5 of 10 cats in group B, and 10 of 11 cats in group C. Group A was significantly protected compared to those in groups B (P 0.063). The preventable fraction was 100% for group A and 45% for group B. At 9 weeks PC, proviral DNA and viral RNA were detected 1 of 11 cats in group A, 6 of 10 cats in group B, and 9 of 11 cats in group C. Nucleic acid loads were significantly lower in group A than in group C (P feline 2-FeLV-vaccinated cats were fully protected against persistent antigenemia and had significantly smaller amounts of proviral DNA and plasma viral RNA loads than PureVax recombinant FeLV-vaccinated cats and unvaccinated controls. Copyright © 2015, Patel et al.

Influenza A outbreaks in Minnesota turkeys due to subtype H10N7 and possible transmission by waterfowl.

Science.gov (United States)

Karunakaran, D; Hinshaw, V; Poss, P; Newman, J; Halvorson, D

1983-01-01

Avian influenza outbreaks in Minnesota involving the H10N7 subtype occurred on two turkey farms in 1979 and on a third in 1980. The H10N7 (Hav2 Neq1) subtype had not previously been detected in turkeys in Minnesota or reported in the United States. The clinical signs ranged from severe, with a mortality rate as high as 31%, to subclinical. Antigenically indistinguishable viruses were isolated from healthy mallards on a pond adjacent to the turkey farms, suggesting that the virus responsible for the outbreak may have been introduced by feral ducks.

Synthesis NiAl{sub 1,0}Fe{sub 1,0}O{sub 4} catalyst by the combustion reaction to their use in the shift reaction (WGSR); Sintese do catalisador de NiAl{sub 1,0}Fe{sub 1,0}O{sub 4} por reacao de combustao visando sua utilizacao na reacao de shift (WGSR)

Energy Technology Data Exchange (ETDEWEB)

Santos, P.T.A.; Costa, A.C.F.M.; Neiva, L.S.; Gama, L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Dept. de Engenharia de Materiais; Argolo, F.; Andrade, H.M.C. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Inst. de Quimica

2009-07-01

This work aims at the synthesis of catalyst NiAl{sub 1,0}Fe{sub 1,0}O{sub 4} by combustion reaction using urea as fuel, to evaluate its performance in the production of hydrogen by the reaction of displacement of water vapor (WGSR). The initial composition of the solution was based on valencia total oxidizing and reducing reagents based on the concepts of the chemistry of propellants, using container as a crucible of glassy silica. The resulting powder was characterized by X-ray diffraction, infrared spectroscopy, nitrogen adsorption isotherms (BET), scanning electronic microscope and catalytic tests. The DRX results reveal the presents majoritary phase NiAl{sub 1,0}Fe{sub 1,0}O{sub 4} spinel, the catalyst presents surface area 28 m{sup 2}/g and isotherms type III. Higher conversion CO/CO{sub 2} of 75% CO conversion observed at 500 deg C and catalytic activity of 43 mmolg{sup -1}.h{sup -1} at 450 deg C. (author)

15 CFR 2008.10 - Declassification authority.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Declassification authority. 2008.10 Section 2008.10 Commerce and Foreign Trade Regulations Relating to Foreign Trade Agreements OFFICE OF THE UNITED STATES TRADE REPRESENTATIVE REGULATIONS TO IMPLEMENT E.O. 12065; OFFICE OF THE UNITED STATES TRADE...

Tunable magnetic properties by interfacial manipulation of L1(0)-FePt perpendicular ultrathin film with island-like structures.

Science.gov (United States)

Feng, C; Wang, S G; Yang, M Y; Zhang, E; Zhan, Q; Jiang, Y; Li, B H; Yu, G H

2012-02-01

Based on interfacial manipulation of the MgO single crystal substrate and non-magnetic AIN compound, a L1(0)-FePt perpendicular ultrathin film with the structure of MgO/FePt-AIN/Ta was designed, prepared, and investigated. The film is comprised of L1(0)-FePt "magnetic islands," which exhibits a perpendicular magnetic anisotropy (PMA), tunable coercivity (Hc), and interparticle exchange coupling (IEC). The MgO substrate promotes PMA of the film because of interfacial control of the FePt lattice orientation. The AIN compound is doped to increase the difference of surface energy between FePt layer and MgO substrate and to suppress the growth of FePt grains, which takes control of island growth mode of FePt atoms. The AIN compound also acts as isolator of L1(0)-FePt islands to pin the sites of FePt domains, resulting in the tunability of Hc and IEC of the films.

Photoionization study of Ne-like K9+, Ca10+, Sc11+, Ti12+, V13+, Cr14+, Mn15+, and Fe16+ ions using the screening constant by unit nuclear charge method

International Nuclear Information System (INIS)

Goyal, Arun; Khatri, Indu; Sow, Malick; Sakho, Ibrahima; Aggarwal, Sunny; Singh, A.K.; Mohan, Man

2016-01-01

Photoionization of the 2s 2 2p 6 ( 1 S 0 ) ground state of the Ne-like (Z=19–29) ions is presented in this paper. Resonance energies and total natural width of the 2s2p 6 np 1 P series of the Ne-like K 9+ , Ca 10+ , Sc 11+ , Ti 12+ , V 13+ , Cr 14+ , Mn 15+ , and Fe 16+ are reported. All the calculations are made using the Screening constant by unit nuclear charge (SCUNC) formalism. New data for Ne-like K 9+ , Sc 11+ , Ti 12+ , V 13+ , Cr 14+ , and Mn 15+ ions are tabulated. Good agreements are found with available literature data. - Highlights: • Photoionization of ground state of the Ne-like (Z=19–29) presented. • good agreements with scarce literature data. • New data for Ne-like K 9+ , Sc 11+ , Ti 12+ , V 13+ , Cr 14+ , and Mn 15+ ions. • Useful guidelines for application in laboratory, astrophysics, and plasma physics.

Intrinsic magnetic properties of L1(0) FeNi obtained from meteorite NWA 6259

Energy Technology Data Exchange (ETDEWEB)

Poirier, E; Pinkerton, FE; Kubic, R; Mishra, RK; Bordeaux, N; Mubarok, A; Lewis, LH; Goldstein, JI; Skomski, R; Barmak, K

2015-05-07

FeNi having the tetragonal L1(0) crystal structure is a promising new rare-earth-free permanent magnet material. Laboratory synthesis is challenging, however, tetragonal L1(0) FeNi-the mineral "tetrataenite"-has been characterized using specimens found in nickel-iron meteorites. Most notably, the meteorite NWA 6259 recovered from Northwest Africa is 95 vol.% tetrataenite with a composition of 43 at.% Ni. Hysteresis loops were measured as a function of sample orientation on a specimen cut from NWA 6259 in order to rigorously deduce the intrinsic hard magnetic properties of its L1(0) phase. Electron backscatter diffraction showed that NWA 6259 is strongly textured, containing L1(0) grains oriented along any one of the three equivalent cubic directions of the parent fcc structure. The magnetic structure was modeled as a superposition of the three orthonormal uniaxial variants. By simultaneously fitting first-quadrant magnetization data for 13 different orientations of the sample with respect to the applied field direction, the intrinsic magnetic properties were estimated to be saturation magnetization 4 pi M-s = 14.7 kG and anisotropy field H-a = 14.4 kOe. The anisotropy constant K = 0.84 MJ/m(3) is somewhat smaller than the value K = 1.3 MJ/m(3) obtained by earlier researchers from nominally equiatomic FeNi prepared by neutron irradiation accompanied by annealing in a magnetic field, suggesting that higher Ni content (fewer Fe antisite defects) may improve the anisotropy. The fit also indicated that NWA 6259 contains one dominant variant (62% by volume), the remainder of the sample being a second variant, and the third variant being absent altogether. (C) 2015 AIP Publishing LLC.

Magnetic properties and microstructure of low ordering temperature L10 FePt thin films

International Nuclear Information System (INIS)

Sun, A.C.; Kuo, P.C.; Chen, S.C.; Chou, C.Y.; Huang, H.L.; Hsu, J.H.

2004-01-01

Polycrystalline Fe 52 Pt 48 alloy thin films were prepared by dc magnetron sputtering on preheated natural-oxidized silicon wafer substrates. The film thickness was varied from 10 to 100 nm. The as-deposited film was encapsulated in a quartz tube and postannealed in vacuum at various temperatures for 1 h, then furnace cooled. It is found that the ordering temperature from as-deposited soft magnetic fcc FePt phase to hard magnetic fct L1 0 FePt phase could be reduced to about 350 deg. C by preheating substrate and furnace cooling treatment. The magnetic properties measurements indicated that the in-plane coercivity of the films was increased rapidly as annealing temperature is increased from 300 to 400 deg. C, but it decreased when the annealing temperature is higher than 400 deg. C. X-ray diffraction analysis shown that the as-deposited FePt thin film was a disorder fcc FePt phase. The magnetic measurement indicated that the transformation of disorder fcc FePt to fct L1 0 FePt phase was started at about 350 deg. C, which is consistent with the analysis of x-ray diffraction patterns. From scanning electron microscopy observation and selected area energy disperse spectrum analysis, the distributions of Fe and Pt elements in the films became nonuniform when the annealing temperature was higher than 500 deg. C due to the formation of the Fe 3 Pt phase. After annealing at 400 deg. C, the in plane coercivity of Fe 52 Pt 48 thin film with film thickness of 100 nm is 10 kOe, M s is 580 emu/cm3, and grain size is about 12 nm

Synthesis of single-phase L10-FeNi magnet powder by nitrogen insertion and topotactic extraction.

Science.gov (United States)

Goto, Sho; Kura, Hiroaki; Watanabe, Eiji; Hayashi, Yasushi; Yanagihara, Hideto; Shimada, Yusuke; Mizuguchi, Masaki; Takanashi, Koki; Kita, Eiji

2017-10-16

Tetrataenite (L1 0 -FeNi) is a promising candidate for use as a permanent magnet free of rare-earth elements because of its favorable properties. In this study, single-phase L1 0 -FeNi powder with a high degree of order was synthesized through a new method, nitrogen insertion and topotactic extraction (NITE). In the method, FeNiN, which has the same ordered arrangement as L1 0 -FeNi, is formed by nitriding A1-FeNi powder with ammonia gas. Subsequently, FeNiN is denitrided by topotactic reaction to derive single-phase L1 0 -FeNi with an order parameter of 0.71. The transformation of disordered-phase FeNi into the L1 0 phase increased the coercive force from 14.5 kA/m to 142 kA/m. The proposed method not only significantly accelerates the development of magnets using L1 0 -FeNi but also offers a new synthesis route to obtain ordered alloys in non-equilibrium states.

Preparation and characterization of Bi26-2xMn2xMo10O69-d and Bi26.4Mn0.6Mo10-2yMe2yO69-d (Me = V, Fe Solid Solutions

Directory of Open Access Journals (Sweden)

Z. A. Mikhaylovskaya

2017-09-01

Full Text Available Single phase samples of bismuth molybdate, Bi26Mo10O69, doped with Mn on the bismuth sublattice and V, Fe on the molybdenum sublattice were found to crystallize in the triclinic Bi26Mo10O69 structure at low doping levels and in the monoclinic Bi26Mo10O69 structure - at higher dopant concentration. The assumption that all Mn ions have an oxidation state of +2 was confirmed by means of magnetic measurement results analysis using Curie-Weiss law. Conductivity was investigated using impedance spectroscopy. The conductivity of Bi26.4Mn0.6Mo9.6Fe0.4O69-d was 1.2*10-2 S*cm-1 at 973 K and 2.2*10-4 S*cm-1 at 623 K, and the conductivity of Bi26.4Mn0.6Mo9.2V0.8O69-d was 2.2*10-3 S*cm-1 at 973 K and 2.2*10-5 S*cm-1 at 623 K.

30 CFR 906.10 - State regulatory program approval.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false State regulatory program approval. 906.10 Section 906.10 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE COLORADO § 906.10 State...

Molecular dynamic simulation study of plasma etching L10 FePt media in embedded mask patterning (EMP) process

OpenAIRE

Jianxin Zhu; P. Quarterman; Jian-Ping Wang

2017-01-01

Plasma etching process of single-crystal L10-FePt media [H. Wang et al., Appl. Phys. Lett. 102(5) (2013)] is studied using molecular dynamic simulation. Embedded-Atom Method [M. S. Daw and M. I. Baskes, Phy. Rev. B 29, 6443 (1984); X. W. Zhou, R. A. Johnson and H. N. G. Wadley, Phy. Rev. B 69, 144113 (2004)] is used to calculate the interatomic potential within atoms in FePt alloy, and ZBL potential [J.F. Ziegler, J. P. Biersack and U. Littmark, “The Stopping and Range of Ions in Matter,” Vol...

Lattice sites, charge states and spin–lattice relaxation of Fe ions in {sup 57}Mn{sup +} implanted GaN and AlN

Energy Technology Data Exchange (ETDEWEB)

Masenda, H., E-mail: hilary.masenda@wits.ac.za [School of Physics, University of the Witwatersrand, Johannesburg 2050 (South Africa); Naidoo, D. [School of Physics, University of the Witwatersrand, Johannesburg 2050 (South Africa); Bharuth-Ram, K. [Physics Department, Durban University of Technology, Durban 4000 (South Africa); iThemba LABS, PO Box 725, Somerset West 7129 (South Africa); Gunnlaugsson, H.P. [PH Department, ISOLDE/CERN, 1211 Geneva 23 (Switzerland); KU Leuven, Instituut voor Kern-en Stralingsfysica, 3001 Leuven (Belgium); Johnston, K. [PH Department, ISOLDE/CERN, 1211 Geneva 23 (Switzerland); Mantovan, R. [Laboratorio MDM, IMM-CNR, Via Olivetti 2, 20864 Agrate Brianza (MB) (Italy); Mølholt, T.E. [PH Department, ISOLDE/CERN, 1211 Geneva 23 (Switzerland); Ncube, M. [School of Physics, University of the Witwatersrand, Johannesburg 2050 (South Africa); Shayestehaminzadeh, S. [Materials Chemistry, RWTH Aachen University, Kopernikusstr. 10, 5274 Aachen (Germany); Gíslason, H.P. [Science Institute, University of Iceland, Dunhaga 3, 107 Reykjavík (Iceland); Langouche, G. [KU Leuven, Instituut voor Kern-en Stralingsfysica, 3001 Leuven (Belgium); Ólafsson, S. [Science Institute, University of Iceland, Dunhaga 3, 107 Reykjavík (Iceland); Weyer, G. [Department of Physics and Astronomy, Aarhus University, Ny Munkegade 120, 8000 Aarhus (Denmark)

2016-03-01

The lattice sites, valence states, resulting magnetic behaviour and spin–lattice relaxation of Fe ions in GaN and AlN were investigated by emission Mössbauer spectroscopy following the implantation of radioactive {sup 57}Mn{sup +} ions at ISOLDE/CERN. Angle dependent measurements performed at room temperature on the 14.4 keV γ-rays from the {sup 57}Fe Mössbauer state (populated from the {sup 57}Mn β{sup −} decay) reveal that the majority of the Fe ions are in the 2+ valence state nearly substituting the Ga and Al cations, and/or associated with vacancy type defects. Emission Mössbauer spectroscopy experiments conducted over a temperature range of 100–800 K show the presence of magnetically split sextets in the “wings” of the spectra for both materials. The temperature dependence of the sextets relates these spectral features to paramagnetic Fe{sup 3+} with rather slow spin–lattice relaxation rates which follow a T{sup 2} temperature dependence characteristic of a two-phonon Raman process. - Highlights: • The majority of the Fe ions are in the 2+ state, located on near substitutional sites associated with vacancy type defects. • A significant fraction of the Fe ions are in the paramagnetic Fe{sup 3+} state. • Spin–lattice relaxation of Fe{sup 3+} in both GaN and AlN follows a two-phonon Raman process.

Low-temperature monocrystal elastic constants of Fe-19Cr-10Ni

International Nuclear Information System (INIS)

Ledbetter, H.M.

1984-01-01

By a pulse-echo-overlap ultrasonic method, we determined the monocrystal elastic constants (C 11 , C 12 , C 44 ) of an Fe-19Cr-10Ni alloy between 295 and 4 K. In composition this laboratory alloy approximates a technological austenitic stainless steel: AISI 304. Many previous studies on polycrystalline steels found a low-temperature magnetic phase transition that affects physical properties, including elastic constants. At the transition, anomalies occur in all polycrystal elastic constants: Young's modulus, shear modulus, bulk modulus, and Poisson's ratio. The present study found that the transition, near 50 K, does not affect one monocrystal elastic constant: C 44 , the resistance to shear on a (100) plane in a [100]-type direction. We interpret this new observation from the viewpoint of a Born-type lattice model. Also, we comment about the relationship between the elastic-constant changes and the low-temperature magnetic state

Nitrogen versus helium: effects of the choice of the atomizing gas on the structures of Fe50Ni30Si10B10 and Fe32Ni36Ta7Si8B17 powders

International Nuclear Information System (INIS)

Zambon, A.

2004-01-01

Gas atomization can produce, besides a possible significant degree of undercooling, high cooling rates, whose extent depends on the size of the droplets, on their velocity with respect to the surrounding medium, on the thermo-physical properties of both the alloy and the gas, and of course on the operating conditions such as melt overheating and gas-to-metal flow ratio. In this respect it is well-known that the atomizing gas can play a significant role in determining both the powder size distribution and the kind and mix of phases which result from the solidification and cooling processes. The microstructures and solidification morphologies of powders obtained from nitrogen and helium sonic gas atomization of two iron-nickel base glass forming alloys, Fe 50 Ni 30 Si 10 B 10 and Fe 32 Ni 36 Ta 7 Si 8 B 17 , were investigated by means of light microscopy, X-ray diffraction (XRD) and differential thermal analysis (DTA). The Fe 32 Ni 36 Ta 7 Si 8 B 17 alloy exhibits a higher proneness to the development of amorphous phase than the Fe 50 Ni 30 Si 10 B 10 alloy, while the effect of the higher speed attainable by the stream of helium with respect to that of nitrogen, affords not only to obtain a larger amount of particles in the finer size ranges, but also to affect the relative amounts of phases within the different size fractions

Absolute measurement of the cross sections of neutron radiative capture for 23Na, Cr, 55Mn, Fe, Ni, 103Rh, Ta, 197Au and 238U in the 10-600keV energy range

International Nuclear Information System (INIS)

Le Rigoleur, Claude; Arnaud, Andre; Taste, Jean.

1976-10-01

The total energy weighting technique has been applied to measuring absolute neutron capture cross sections for 23 Na, Cr, 55 Mn, Fe, Ni, 103 Rh, Ta, 197 Au, 238 U in the 10-600keV energy range. A non hydrogeneous liquid scintillator was used to detect the gamma from the cascade. The neutron flux was measured with a 10 B INa(Tl) detector or a 6 Li glass scintillator of well known efficiency. The fast time-of-flight technique was used with on line digital computer data processing [fr

Structure and magnetic properties of L10-FePt thin films on TiN/RuAl underlayers

International Nuclear Information System (INIS)

Yang En; Ratanaphan, Sutatch; Zhu Jiangang; Laughlin, David E.

2011-01-01

Highly ordered L1 0 FePt-oxide thin films with small grains were prepared by using a RuAl layer as a grain size defining seed layer along with a TiN barrier layer. Different HAMR (Heat Assisted Magnetic Recording) favorable underlayers were studied to encourage perpendicular texture and preferred microstructure. It was found that the epitaxial and small grain growth from the RuAl/TiN underlayer results in small and uniform grains in the FePt layer with perpendicular texture. By introducing the grain size defining underlayers, the FePt grain size can be reduced from 30 to 6 nm with the same volume fraction (9%) of SiO 2 in the film, excellent perpendicular texture, and very high order parameter at 520 deg. C.

Behavior of methyl orange and orange 10 (orange G) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe; Comportamiento de naranja de metilo y naranja 10 (orange G) en presencia de compuestos tipo hidrotalcita de mg/Al y Mg/Fe

Energy Technology Data Exchange (ETDEWEB)

Cruz N, G.

2015-07-01

This work is focused on studying the sorption capacity of methyl orange dye (Nm) and orange 10 (N-10) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe uncalcined and calcined previously at 500 degrees Celsius. Sorption isotherms were determined and the study of the kinetics of sorption was performed. The materials were characterized before and after sorption processes of these dyes by X-ray diffraction, scanning electron microscopy, the specific surface area determination by the Brunauer-Emmett-Teller method, thermogravimetry coupled to mass and infrared spectrometry. The hydrotalcite type compounds reported in this paper were prepared in the laboratory and their acronyms are: HTMgAlG1, HTMgAlMO, HTMgFeG1 and HTMgFeG2. Note that in this work the best conditions for preparing compounds of Mg/Fe were found. From patterns of X-ray diffraction was identified the typical crystal structure of the hydrotalcite type compounds. By scanning electron microscopy the morphology could be determined in the form of flakes characteristics of these compounds. Likewise with elemental analysis of energy dispersive X-ray spectroscopy the presence of Mg, Al, Fe and C, elements of interest for this study was determined. The compounds presented a specific surface area relatively high from 80 to 120 m{sup 2}/g. Thermogravimetry results presented spectra of mass loss very characteristic associated to water losses, dehydroxylation and decarboxylation. The characteristic bands of water and carbonate were assigned by infrared spectroscopy and the bands corresponding to the dyes sulfonates were identified only for the calcined materials. The sorption capacities found of these compounds were as follows: for Nm in the compound HTMgAlG1 uncalcined was 17.82 mg/g for an initial concentration of 200 mg/L and for calcined (HTMgAlMOcal) of 99.8 mg/g with and initial concentration of 1000 mg/L. Moreover, the sorption capacity of the dye N-10 in this same material was 17.92 mg/g and 99

Single phase semipolar (11 anti 22) GaN on (10 anti 10) sapphire

Energy Technology Data Exchange (ETDEWEB)

Ploch, S.; Stellmach, J.; Schwaner, T.; Frentrup, M.; Wernicke, T.; Pristovsek, M.; Kneissl, M. [Institute of Solid States Physics, (Germany); Park, J.B.; Niermann, T.; Lehmann, M. [Institute of Optics and Atomic Physics, TU Berlin, Hardenbergstr. 36, 10623 Berlin (Germany)

2011-07-01

InGaN quantum well based light emitters grown on (0001) GaN suffer from poor quantum efficiencies with increasing indium mole fraction due to strong polarization fields along the polar crystal orientation. This effect can be greatly reduced by growing on semi- and non-polar GaN orientations. Semipolar (11 anti 22) GaN layers were deposited by metalorganic vapour phase epitaxy on (10 anti 10) sapphire. After sapphire substrate nitridation at 1000 C, a GaN nucleation layer was deposited at high temperature, followed by the deposition of 1.5 nm thick GaN buffer layers. The samples show predominantly (11 anti 22) orientation with a small fraction of (10 anti 13) oriented domains. With increasing nitridation layer thickness the (10 anti 13) phase is suppressed leading to a very smooth surface morphology (rms roughness < 4nm). PL measurements show dominant basel plane stacking fault (BSF) I{sub 1} luminescence without any other defects. Transmission electron microscopy measurements reveal a high BSF density. The FWHM of the X-ray diffraction rocking curve measurements of the (1122) reflection decreases to 1193 arcsec and 739 arcsec along [1 anti 100] and [11 anti 23] respectively with increasing nucleation temperature. Using high temperature nucleation smooth and homogeneous (11 anti 22) phase GaN layers have been obtained.

77 FR 30584 - Notice of Termination of United States-Bolivia Bilateral Investment Treaty

Science.gov (United States)

2012-05-23

... of Termination of United States--Bolivia Bilateral Investment Treaty AGENCY: Department of State and Office of the United States Trade Representative. ACTION: Notice. SUMMARY: The Government of Bolivia has...-9580. SUPPLEMENTARY INFORMATION: Bolivia delivered notice on June 10, 2011, that it was terminating the...

RRh2Al10 (R = Ce, Yb): New intermetallic compounds in the 1 : 2 : 10 stoichiometry series

Science.gov (United States)

Strydom, A. M.; Djoumessi, R. F.; Blinova, M.; Tursina, A.; Nesterenko, S.; Avzuragova, V.

2018-05-01

The orthorhombic, space group Cmcm YbFe2Al10 structure type series of compounds are known to form with practically the entire series of rare-earth elements R, but only with the three d - electron elements Fe, Ru, and Os. The Ce-derivatives in particular have been of much interest since the first reports of their highly unusual physical properties. Classified as Kondo insulators, CeRu2Al10 and CeOs2Al10 controversially order magnetically and with uncharacteristically high Néel temperatures of ≃ 28 K. CeFe2Al10 on the other hand shows pronounced semiconducting and Kondo features but remains paramagnetic. As part of our ongoing studies into the rich physics of this class of materials we have succeeded in synthesizing new members of the 1:2:10 stoichiometry involving the chemical element Rh for the first time. CeRh2Al10 is found to crystallize in the tetragonal system with space group I41 / amd . Yb Rh2Al10 on the other hand forms in the serial Cmcm orthorhombic structure type. We discuss important similarities between the two types. At 5.310 Å the shortest Ce-Ce distance is, likewise to the situation in CeRu2Al10 and CeOs2Al10 , also well above the Hill limit of 3.40 Å. Despite the cage-like structure and large rare-earth separation distances, this study reveals the onset of long-range magnetic ordering in CeRh2Al10 at 3.9 K. The magnetic ordering develops out of an incoherent Kondo state that dominates the electrical resistivity below about 40 K.

Formation of Al70Cu20Fe10 icosahedral quasicrystal by mechanically alloyed method

International Nuclear Information System (INIS)

Yin Shilong; Bian Qing; Qian Liying; Zhang Aimei

2007-01-01

The structural evolutions of the mechanically alloyed ternary Al 70 Cu 20 Fe 10 powders with the milling time and the annealing treatment have been studied by X-ray diffraction (XRD), transmission electronic microscopy (TEM) and X-ray absorption fine-structure spectroscopy (XAFS) techniques. Results show that an Al 2 Cu compound forms with short-time milling, while a Cu 9 Al 4 compound forms with long-time milling. Fe can react with Al-Cu alloy by annealing treatment. Al 7 Cu 2 Fe compound with tetragonal structure or Al (Cu, Fe) solid solution with cubic structure may form at lower temperature, while a quasicrystal phase of Al 65 Cu 20 Fe 15 alloy may form at higher temperature

Correlation between the nanocrystalline Sm(Fe,Mo){sub 12} and its out of equilibrium phase Sm(Fe,Mo){sub 10}

Energy Technology Data Exchange (ETDEWEB)

Khazzan, S. [CMTR, ICMPE, UMR7182, CNRS - Université Paris Est, 2-8 rue Henri Dunant, F-94320 Thiais (France); Laboratoire Matériaux Organisation et Propriétés, Faculté des Sciences de Tunis, Université de Tunis El Manar, 2092 Tunis (Tunisia); Bessais, L., E-mail: bessais@glvt.cnrs.fr [CMTR, ICMPE, UMR7182, CNRS - Université Paris Est, 2-8 rue Henri Dunant, F-94320 Thiais (France); Van Tendeloo, G. [EMAT, University of Antwerp, B-2020 Antwerp (Belgium); Mliki, N. [Laboratoire Matériaux Organisation et Propriétés, Faculté des Sciences de Tunis, Université de Tunis El Manar, 2092 Tunis (Tunisia)

2014-08-01

Nanostructured Sm–Fe–Mo semi-hard magnetic material exhibiting enhanced magnetic properties can be produced by ball milling followed by recrystallization. Milled samples were annealed for 30 min in a vacuum at different temperatures (T{sub A}) between 700 and 1190 °C. The effects of heat treatment and Mo content on structural and magnetic property changes have been investigated by means of X-ray diffraction using the Rietveld method, transmission electron microscopy and magnetic measurements. For samples annealed at T{sub A}>900°C the tetragonal ThMn{sub 12}-type structure is identified, while for 70010, for the out of equilibrium hexagonal phase, which is described with three crystallographic transition metal sites: 3g is fully occupied, 6l occupation is limited to hexagons surrounding the Fe dumbbell pairs 2e. We have performed a magnetic and structural study of nanocrystalline metastable P6/mmm Sm(Fe{sub 1−x}Mo{sub x}){sub 10}, correlated with structural transformation towards its equilibrium derivative I4/mmm Sm(Fe{sub 1−x}Mo{sub x}){sub 12}. A maximum of the coercive field H{sub C} (H{sub C}>5kOe) has been observed for the new hexagonal P6/mmm phase suggesting that nanocrystalline Sm(Fe,Mo){sub 10}, is a semi-hard material, and is potential candidate for magnetic recording. - Highlights: • A study of the structure and magnetic properties of SmFeMo compound. • A new out of equilibrium P6/mmm-type structure was found. • Correlation between the 1/12 phase and its out of equilibrium 1/10 phase.

Beryllium-10 in Chesapeake Bay sediments: an indicator of sediment provenance

International Nuclear Information System (INIS)

Helz, G.R.; Valette-Silver, Nathalie

1992-01-01

In a plot of 10 Be vs. Fe, central Chesapeake Bay sediments can be segregated into distinct units. This plot reveals an unexpected, statistically significant difference between sediments on the eastern and western flanks of the main channel, implying different origins. Although the 10 Be concentrations in sediments from these two regions span as much as an order of magnitude range, the 10 Be/Fe ratios vary by an amount approximating analytical error alone. The large concentration ranges are ascribed to hydraulic sorting, which can produce variance in composition while not affecting ratios between grain surface components such as Fe and Be. On the basis of 10 Be/Fe signatures, sediments on the western flank of the main channel appear to have been derived from the Susquehanna or another Piedmont/Appalachian river. Sediments on the eastern flank may have been transported from the south, by landward flowing bottom currents, or may be relics of a Pleistocene estuarine system. Conditions under which 10 Be may prove a useful tool in sediment provenance studies elsewhere are discussed. (Author)

Age of diagnosis of breast cancer in china: almost 10 years earlier than in the United States and the European union.

Science.gov (United States)

Song, Qing-Kun; Li, Jing; Huang, Rong; Fan, Jin-Hu; Zheng, Rong-Shou; Zhang, Bao-Ning; Zhang, Bin; Tang, Zhong-Hua; Xie, Xiao-Ming; Yang, Hong-Jian; He, Jian-Jun; Li, Hui; Li, Jia-Yuan; Qiao, You-Lin; Chen, Wan-Qing

2014-01-01

The study aimed to describe the age distribution of breast cancer diagnosis among Chinese females for comparison with the United States and the European Union, and provide evidence for the screening target population in China. Median age was estimated from hospital databases from 7 tertiary hospitals in China. Population-based data in China, United States and European Union was extracted from the National Central Cancer Registry, SEER program and GLOBOCAN 2008, respectively. Age-standardized distribution of breast cancer at diagnosis in the 3 areas was estimated based on the World Standard Population 2000. The median age of breast cancer at diagnosis was around 50 in China, nearly 10 years earlier than United States and European Union. The diagnosis age in China did not vary between subgroups of calendar year, region and pathological characteristics. With adjustment for population structure, median age of breast cancer at diagnosis was 50~54 in China, but 55~59 in United States and European Union. The median diagnosis age of female breast cancer is much earlier in China than in the United States and the European Union pointing to racial differences in genetics and lifestyle. Screening programs should start at an earlier age for Chinese women and age disparities between Chinese and Western women warrant further studies.

Statistical modeling of the reactions Fe(+) + N2O → FeO(+) + N2 and FeO(+) + CO → Fe(+) + CO2.

Science.gov (United States)

Ushakov, Vladimir G; Troe, Jürgen; Johnson, Ryan S; Guo, Hua; Ard, Shaun G; Melko, Joshua J; Shuman, Nicholas S; Viggiano, Albert A

2015-08-14

The rates of the reactions Fe(+) + N2O → FeO(+) + N2 and FeO(+) + CO → Fe(+) + CO2 are modeled by statistical rate theory accounting for energy- and angular momentum-specific rate constants for formation of the primary and secondary cationic adducts and their backward and forward reactions. The reactions are both suggested to proceed on sextet and quartet potential energy surfaces with efficient, but probably not complete, equilibration by spin-inversion of the populations of the sextet and quartet adducts. The influence of spin-inversion on the overall reaction rate is investigated. The differences of the two reaction rates mostly are due to different numbers of entrance states (atom + linear rotor or linear rotor + linear rotor, respectively). The reaction Fe(+) + N2O was studied either with (6)Fe(+) or with (4)Fe(+) reactants. Differences in the rate constants of (6)Fe(+) and (4)Fe(+) reacting with N2O are attributed to different contributions from electronically excited potential energy surfaces, such as they originate from the open-electronic shell reactants.

31 CFR 515.334 - United States national.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false United States national. 515.334 Section 515.334 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... of the United States, and which has its principal place of business in the United States. [61 FR...

Non-equilibrium magnetic properties of melt-spun Nd60Fe30Al10 alloys

International Nuclear Information System (INIS)

Sato Turtelli, R.; Sinnecker, J.P.; Steiner, W.; Wiesinger, G.; Groessinger, R.; Triyono, D.

2003-01-01

The temperature, frequency and DC-field dependence of the AC-susceptibility has been investigated on melt-spun Nd 60 Fe 30 Al 10 . The temperature dependence of the AC-susceptibility shows an anomalous behavior, which depends strongly on the applied heat treatment and exhibits a cluster-like characteristic. Similar to the time dependence of the coercivity, a magnetic after-effect is present for temperatures higher than 50 K. 57 Fe Moessbauer spectra can be analyzed by two hyperfine field distributions pointing to two phases with quite different magnetic moments on the Fe sites

7 CFR 1220.615 - State and United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false State and United States. 1220.615 Section 1220.615... CONSUMER INFORMATION Procedures To Request a Referendum Definitions § 1220.615 State and United States. State and United States include the 50 States of the United States of America, the District of Columbia...

7 CFR 1220.129 - State and United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false State and United States. 1220.129 Section 1220.129... CONSUMER INFORMATION Soybean Promotion and Research Order Definitions § 1220.129 State and United States. The terms State and United States include the 50 States of the United States of America, the District...

Photo-Hall-effect study of excitation and recombination in Fe-doped GaN

Science.gov (United States)

Look, David C.; Leach, Jacob H.; Metzger, Robert

2017-02-01

The photo-Hall-effect was applied to the study of electron dynamics in semi-insulating Fe-doped GaN. High-powered light-emitting diodes of wavelengths λ = 940, 536, 449, 402, and 365 nm were used to excite steady-state free-electron volume concentrations Δn = 105-108 cm-3, depending on λ and intensity I0. Electron lifetime τ was determined from the energy E dependence of the excited sheet electron concentration Δns through the relationship Δns = I0τA(E), where the absorbance A(E) is a known function of sample thickness d and absorption coefficient α, and the energy dependence of α is taken from a theory of deep-center photoionization. The major sample impurities were Fe, Si, and C, with [Fe] ≫ [Si] and [C]. Fitted lifetimes τ ranged from 15 to 170 ps, depending on [Fe]. It was found that Δns ∝ I0 for [Si] > [C] and ∝ I01/2 for [Si] [C], some of the neutral Fe3+ is converted to Fe2+ with ground state Fe2+(5E) and excited state Fe2+(5T2); a fit of n vs. temperature T over the range of 290-325 K in the dark establishes E5E with respect to the conduction band: ECB - E5E = 0.564 eV - β5ET, where β5E = 3.6 × 10-4 eV/K. At room temperature, 294 K, ECB - E5E = 0.46 eV and ECB - E5T2 = 0.07 eV.

DFT calculations of strain and interface effects on electronic structures and magnetic properties of L10-FePt/Ag heterojunction of GMR applications

Science.gov (United States)

Pramchu, Sittichain; Jaroenjittichai, Atchara Punya; Laosiritaworn, Yongyut

2018-03-01

In this work, density functional theory (DFT) was employed to investigate the effect of strain and interface on electronic structures and magnetic properties of L10-FePt/Ag heterojunction. Two possible interface structures of L10-FePt(001)/Ag(001), that is, interface between Fe and Ag layers (Fe/Ag) and between Pt and Ag layers (Pt/Ag), were inspected. It was found that Pt/Ag interface is more stable than Fe/Ag interface due to its lower formation energy. Further, under the lattice mismatch induced tensile strain, the enhancement of magnetism for both Fe/Ag and Pt/Ag interface structures has been found to have progressed, though the magnetic moments of "interfacial" Fe and Pt atoms have been found to have decreased. To explain this further, the local density of states (LDOS) analysis suggests that interaction between Fe (Pt) and Ag near Fe/Ag (Pt/Ag) interface leads to spin symmetry breaking of the Ag atom and hence induces magnetism magnitude. In contrast, the magnetic moments of interfacial Fe and Pt atoms reduce because of the increase in the electronic states near the Fermi level of the minority-spin electrons. In addition, the significant enhancements of the LDOS near the Fermi levels of the minority-spin electrons signify the boosting of the transport properties of the minority-spin electrons and hence the spin-dependent electron transport at this ferromagnet/metal interface. From this work, it is expected that this clarification of the interfacial magnetism may inspire new innovation on how to improve spin-dependent electron transport for enhancing the giant magnetoresistance (GMR) ratio of potential GMR-based spintronic devices.

DFT calculations of strain and interface effects on electronic structures and magnetic properties of L10-FePt/Ag heterojunction of GMR applications

Directory of Open Access Journals (Sweden)

Sittichain Pramchu

2018-03-01

Full Text Available In this work, density functional theory (DFT was employed to investigate the effect of strain and interface on electronic structures and magnetic properties of L10-FePt/Ag heterojunction. Two possible interface structures of L10-FePt(001/Ag(001, that is, interface between Fe and Ag layers (Fe/Ag and between Pt and Ag layers (Pt/Ag, were inspected. It was found that Pt/Ag interface is more stable than Fe/Ag interface due to its lower formation energy. Further, under the lattice mismatch induced tensile strain, the enhancement of magnetism for both Fe/Ag and Pt/Ag interface structures has been found to have progressed, though the magnetic moments of “interfacial” Fe and Pt atoms have been found to have decreased. To explain this further, the local density of states (LDOS analysis suggests that interaction between Fe (Pt and Ag near Fe/Ag (Pt/Ag interface leads to spin symmetry breaking of the Ag atom and hence induces magnetism magnitude. In contrast, the magnetic moments of interfacial Fe and Pt atoms reduce because of the increase in the electronic states near the Fermi level of the minority-spin electrons. In addition, the significant enhancements of the LDOS near the Fermi levels of the minority-spin electrons signify the boosting of the transport properties of the minority-spin electrons and hence the spin-dependent electron transport at this ferromagnet/metal interface. From this work, it is expected that this clarification of the interfacial magnetism may inspire new innovation on how to improve spin-dependent electron transport for enhancing the giant magnetoresistance (GMR ratio of potential GMR-based spintronic devices.

75 FR 35611 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, and MD-10-10F...

Science.gov (United States)

2010-06-23

... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, and MD-10-10F Airplanes... certain McDonnell Douglas Model DC-10-10, DC-10-10F, and MD-10-10F airplanes. That NPRM was published in... amends Sec. 39.13 by adding the following new AD: 2010-13-06 McDonnell Douglas Corporation: Amendment 39...

Direct Observation of High-Temperature Superconductivity in One-Unit-Cell FeSe Films

International Nuclear Information System (INIS)

Zhang Wen-Hao; Zhang Jin-Song; Li Fang-Sen; Guo Ming-Hua; Ding Hao; Tang Chen-Jia; Wang Qing-Yan; He Ke; Ji Shuai-Hua; Chen Xi; Sun Yi; Zhao Yan-Fei; Xing Ying; Wang Hui-Chao; Zhang Hui-Min; Peng Jun-Ping; Li Zhi; Wang Meng; Fujita Takeshi; Hirata Akihiko

2014-01-01

We prepared one-unit-cell (1-UC) thick FeSe films on insulating SrTiO 3 substrates with non-superconducting FeTe protection layers by molecular beam epitaxy for ex situ studies. By direct transport and magnetic measurements, we provide definitive evidence for high temperature superconductivity in the 1-UC FeSe films with an onset T C above 40 K and an extremely large critical current density J C ∼1.7×10 6 A/cm 2 at 2 K, which are much higher than T C ∼8 K and J C ∼10 4 A/cm 2 for bulk FeSe, respectively. Our work may pave the way to enhancing and tailoring superconductivity by interface engineering. (express letter)

38 CFR 6.10 - Options.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Options. 6.10 Section 6.10 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS UNITED STATES GOVERNMENT LIFE INSURANCE Optional Settlement § 6.10 Options. Insurance will be payable in one sum only when...

Combined Radix-10 and Radix-16 Division Unit

DEFF Research Database (Denmark)

Lang, Tomas; Nannarelli, Alberto

2007-01-01

In this work we extend a previously proposed digit-recurrence radix-10 division unit to be able to perform also radix-16 division. The extension is simplified by the fact that in the radix-10 implementation the quotient digit is decomposed into two parts and that this decomposition is also...... the selection constants. The rest of the modifications relate to the generation of multiples, to the carry-save adder, to the carry-propagate adder, and to the on-the-fly conversion and rounding. The implementation results show that the delay of an iteration is similar to that of the radix-10 case...

43 CFR 17.10 - Judicial review.

Science.gov (United States)

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Judicial review. 17.10 Section 17.10... Origin § 17.10 Judicial review. Action taken pursuant to section 602 of the act is subject to judicial review as provided in section 603 of the act. [29 FR 16293, Dec. 4, 1964] ...

Electronic configuration of nFe/3Cr/nFe (n=1-6) trilayers in FM state

International Nuclear Information System (INIS)

Botana, J.; Pereiro, M.; Baldomir, D.; Arias, J.E.; Warda, K.; Wojtczak, L.

2007-01-01

Ab initio calculations have been performed on several ultrathin Fe/Cr/Fe trilayer systems in ferromagnetic configuration, with a fixed width of the spacer chromium slab of three atomic monolayers, and both iron slabs symmetrically varying in a range from 1 to 6 atomic monolayers. We have calculated the charge distribution of these trilayers and calculated and plotted the density of states of every one of them. We have identified Friedel-like oscillations of the charge distribution from the Mulliken population analysis in the Fe slabs

Modeling thermodynamics of Fe-N phases; characterisation of e-Fe2N1-z

DEFF Research Database (Denmark)

Pekelharing, M.I.; Böttger, A.; Somers, Marcel A.J.

1999-01-01

In order to arrive at modeling the thermodynamics of Fe-N phases, including long-range (LRO) and short-range ordering (SRO) of the N atoms, it is important to understand the role of N interstitially dissolved in an Fe-host lattice. The crystal structure of -Fe2N1-z consists of an h.c.p. iron...... sublattice and a hexagonal nitrogen sublattice formed by octahedral interstices of the Fe sublattice [1]. Two ground-state structures have been proposed for the ordered arrangement of the N atoms on their own sublattice [1], which were shown to be thermodynamically favourable [2]: configuration A for Fe2N1...... investigated with X-ray diffraction (XRD) and Mössbauer spectroscopy. A thermodynamic model accounting for the two configurations of LRO of the N atoms [2,3] was fitted to the N-absorption isotherm at 723 K and resulted in the occupancies of the sites of the nitrogen sublattice. A miscibility gap between...

Structural investigations of interfaces in Fe{sub 90}Sc{sub 10} nanoglasses using high-energy x-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Ghafari, M.; Gleiter, H.; Feng, T. [Karlsruhe Institute of Technology (KIT), Institute for Nanotechnology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Kohara, S. [Research and Utilization Division, Japan Synchrotron Radiation Research Institute/SPring-8, 1-1-1 Kouto, Sayo-cho, Sayo-gun, Hyogo 679-5198 (Japan); Hahn, H.; Witte, R. [Karlsruhe Institute of Technology (KIT), Institute for Nanotechnology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); KIT-TUD Joint Research Laboratory Nanomaterials, Technische Universitaet Darmstadt, Petersenstr. 32, 64287 Darmstadt (Germany); Kamali, S. [Department of Chemistry, University of California, One Shields Ave., Davis, California 95616 (United States)

2012-03-26

High-resolution diffraction experiments of Fe{sub 90}Sc{sub 10} nanoglasses and rapidly quenched metallic glasses as reference materials have been performed using high-energy x-rays with a wavelength of 0.21 Angst from a synchrotron radiation source. Nanoglasses are amorphous alloys with a significant fraction of interfaces on the nanometer scale. The short- and intermediate-range orders of a nanoglass are different from the well known amorphous materials produced by rapid quenching from the melt. These structural modifications have significant influence on the physical properties. In this paper, the short- and intermediate-range orders of the nanoglass Fe{sub 90}Sc{sub 10} and the reference metallic glass Fe{sub 90}Sc{sub 10} alloy prepared by rapid quenching are discussed.

19 CFR 10.202 - Definitions.

Science.gov (United States)

2010-04-01

... that date, except as otherwise provided in §§ 10.241 through 10.248; (2) Rum and tafia classified in subheading 2208.40, Harmonized Tariff Schedule of the United States; (3) Sugars, syrups, and sugar-containing...

Neutron transitions within the S=10 ground multiplet of a Fe8 magnetic cluster

Science.gov (United States)

Carretta, S.; Liviotti, E.; Amoretti, G.; Caciuffo, R.; Caneschi, A.; Gatteschi, D.

2002-02-01

Inelastic neutron scattering has been used to determine the anisotropic spin Hamiltonian that splits the S=10 ground multiplet of the cluster (tacn)6Fe8O2(OH)12Br4.3(ClO4)3.76H2O (Fe8PCl), where (tacn) is the organic ligand 1,4,7-triazacyclononane. This single-molecule magnet,which is obtained from the well known Fe8Br cluster, by partial replacement of the bromide ions by perchlorate anions, presents a larger transverse anisotropy than the parent compound, the E/D ratio being 0.22 instead of 0.16. This is in agreement with the relaxation measurements in the pure quantum tunneling regime. The details of the neutron spectra detected at three different temperatures (2, 10, and 15 K) allowed us to determine the spin Hamiltonian parameters up to fourth order and to identify the main source of the transition linewidth broadening with the occupational disorder of the bromide and perchlorate ions, rather than with the random internal dipolar field distribution.

The influence of Fe doping on the surface topography of GaN epitaxial material

International Nuclear Information System (INIS)

Cui Lei; Yin Haibo; Jiang Lijuan; Wang Quan; Feng Chun; Xiao Hongling; Wang Cuimei; Wang Xiaoliang; Gong Jiamin; Zhang Bo; Li Baiquan; Wang Zhanguo

2015-01-01

Fe doping is an effective method to obtain high resistivity GaN epitaxial material. But in some cases, Fe doping could result in serious deterioration of the GaN material surface topography, which will affect the electrical properties of two dimensional electron gas (2DEG) in HEMT device. In this paper, the influence of Fe doping on the surface topography of GaN epitaxial material is studied. The results of experiments indicate that the surface topography of Fe-doped GaN epitaxial material can be effectively improved and the resistivity could be increased after increasing the growth rate of GaN materials. The GaN material with good surface topography can be manufactured when the Fe doping concentration is 9 × 10 19 cm −3 . High resistivity GaN epitaxial material which is 1 × 10 9 Ω·cm is achieved. (paper)

Magnetization, magnetic susceptibility, effective magnetic moment of Fe3+ ions in Bi25FeO39 ferrite

International Nuclear Information System (INIS)

Zatsiupa, A.A.; Bashkirov, L.A.; Troyanchuk, I.O.; Petrov, G.S.; Galyas, A.I.; Lobanovsky, L.S.; Truhanov, S.V.

2014-01-01

Magnetic susceptibility for ferrite Bi 25 FeO 39 is measured at 5–950 K in the magnetic field of 0.86 T. It is shown that Bi 25 FeO 39 is paramagnetic in the temperature range 5−950 K. The saturation magnetization is equal to 5.04μ B per formula unit at 5 K in a magnetic field of 10 T. It is found that at 5−300 K the effective magnetic moment of Fe 3+ ions in Bi 25 FeO 39 is equal to 5.82μ B . - Graphical abstract: The dependence of the magnetization (n, μ B ) on the magnetic field for one formula unit of Bi 25 FeO 39 at 5 K. - Highlights: • Magnetic susceptibility for Bi 25 FeO 39 is measured at 5–950 K in the magnetic field of 0.86 T. • It is shown that Bi 25 FeO 39 is paramagnetic in the temperature range 5−950 K. • The saturation magnetization is equal to 5.04μ B per formula unit at 5 K in a magnetic field of 10 T

Effect of boron addition to the hard magnetic bulk Nd60Fe30Al10 amorphous alloy

International Nuclear Information System (INIS)

Kong, H.Z.; Li, Y.; Ding, J.

2000-01-01

A detailed study of the effect of boron addition to crystallinity, magnetic properties and thermal properties was carried out for alloys Nd 60-x Fe 30 Al 10 B x with x=0, 1, 3 and 5 produced by copper mold chill casting and melt-spinning. The cast rods of alloys Nd 60-x Fe 30 Al 10 B x were largely amorphous. Remanence up to 0.154 T and coercivity up to 355 kA/m were observed, which were higher than those of the bulk amorphous Nd 60 Fe 30 Al 10 rod of the same diameter. A step in hysteresis loop was observed for the hard magnetic cast rod and ribbon melt-spun at a low speed of 5 m/s of the alloys with boron addition. Consistent increase in the amplitude of the step and magnetic field (H) at which the step was observed as the boron content increased. A single magnetic phase with low coercivity was observed for fully amorphous ribbon melt-spun at high speed of 30 m/s. Full crystallization due to heat treatment resulted in transition of hard magnetic amorphous phase of Nd 55 Fe 30 Al 10 B 5 cast rod to paramagnetic crystalline phases. TEM results of the as-cast rods illustrated the existence of numerous minute Nd-crystallites in amorphous matrix

22 CFR 901.10 - Act.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Act. 901.10 Section 901.10 Foreign Relations FOREIGN SERVICE GRIEVANCE BOARD GENERAL Meanings of Terms As Used in This Chapter § 901.10 Act. Act means the Foreign Service Act of 1980 (Pub. L. 96-465, October 17, 1980), as amended. [56 FR 55458, Oct. 28...

7 CFR 1209.21 - State and United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false State and United States. 1209.21 Section 1209.21... Definitions § 1209.21 State and United States. (a) State means any of the several States, the District of Columbia, and the Commonwealth of Puerto Rico. (b) United States means collectively the several States of...

Fe doping for making resistive GaN layers with low dislocation density; consequence on HEMTs

Energy Technology Data Exchange (ETDEWEB)

Bougrioua, Z.; Lorenzini, P. [CRHEA-CNRS, rue Bernard Gregory, 06560 Valbonne (France); Azize, M. [CRHEA-CNRS, rue Bernard Gregory, 06560 Valbonne (France); LUMILOG, 2720 Chemin St Bernard, 06220 Vallauris (France); Jimenez, A. [E. Politecnica. Universidad de Alcala, 28871 Alcala de Henares (Spain); Brana, A.F.; Munoz, E. [ETSI Telecomunicacion, UPM, 28040 Madrid (Spain); Beaumont, B.; Gibart, P. [LUMILOG, 2720 Chemin St Bernard, 06220 Vallauris (France)

2005-05-01

Highly resistive GaN (>10{sup 8} {omega}{sub {upsilon}}) is grown by MOVPE on sapphire with dislocation density in the range 10{sup 8} to 8 x 10{sup 8} cm{sup -2}, using Fe modulation doping. High mobility 2DEGs are created at AlGaN/GaN:Fe interface for moderate Al composition: 2200 cm{sup 2}/V/s at n{sub s}{proportional_to}7.6 x 10{sup 12} cm{sup -2}. Good DC and RF small signal behaviour could be obtained in HEMTs processed on structures with less dislocated GaN:Fe template: I{sub DS}{sup max}=1.28 A/mm, g{sub m}{sup max} {proportional_to}290 mS/mm and f{sub T} {proportional_to}23 GHz were measured for 0.2 {mu}m transistors. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Communication of nuclear data progress: No.10 (1993)

International Nuclear Information System (INIS)

1993-12-01

Communication of Nuclear Data Progress (CNDP) is set up by Chinese Nuclear Data Center. This is the tenth issue. It includes the measurements of 54 Fe(d,α), 56 Fe(d,2n), 58 Ni(d,α), (d,αn), (d,x) 57 Ni, 182∼184 W(d,2n), 186 W(d,p), (d 2n) and 58 Ni(n,α) reactions; theoretical calculations on n + 16 O and 197 Au, 10 B(n,n) and (n,n') reactions, channel theory of fission with diffusive dynamics; the evaluations of intermediate energy nuclear data for 56 Fe, 63 Cu, 65 Cu(p,n) monitor reactions, and of 180 Hf, 181 Ta(n,2n) reactions, revision on recommended data of 235 U and 238 U for CENDL-2, fission barrier parameters sublibrary, a PC software of EXFOR compilation, some reports on atomic and molecular data and covariance research

39 CFR 10.1 - Applicability.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Applicability. 10.1 Section 10.1 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE RULES OF CONDUCT FOR POSTAL SERVICE GOVERNORS (ARTICLE X) § 10.1 Applicability. This part contains rules of conduct for the...

Permeability and giant magnetoimpedance in Co69Fe4.5X1.5Si10B15 (X=Cr, Mn, Ni) amorphous ribbons

International Nuclear Information System (INIS)

Byon, Kwang Seok; Yu, Seong-Cho; Kim, Cheol Gi

2001-01-01

The magnetoimpedance (MI) has been measured in the amorphous ribbons of the soft ferromagnetic alloy Co 69 Fe 4.5 X 1.5 Si 10 B 15 (X=Cr, Mn, Ni) as functions of frequency (f). For all of the three samples, at low frequency, f≤5MHz, the MI ratio increases with increasing frequency, but the MI ratio decreases at high frequency, f≥5MHz. The MI profiles are not changed at low frequency regions of f≤1MHz in the amorphous ribbons. The MI ratio at high frequency of f=5MHz becomes 57% in Co 69 Fe 4.5 Cr 1.5 Si 10 B 15 , but the MI ratio becomes 30% in Co 69 Fe 4.5 Mn 1.5 Si 10 B 15 and Co 69 Fe 4.5 Ni 1.5 Si 10 B 15 . The MI ratio at f=10MHz becomes 45% in Co 69 Fe 4.5 Cr 1.5 Si 10 B 15 and the MI ratio becomes 23% in Co 69 Fe 4.5 Mn 1.5 Si 10 B 15 and Co 69 Fe 4.5 Ni 1.5 Si 10 B 15 , respectively. The maximum values of field sensitivity are 2.7(X=Cr), 2.5(X=Mn), 2.2(X=Ni)%/Oe for f=5MHz. [copyright] 2001 American Institute of Physics

Facile synthesis of Fe4N/Fe2O3/Fe/porous N-doped carbon nanosheet as high-performance anode for lithium-ion batteries

Science.gov (United States)

Zhang, Dan; Li, Guangshe; Yu, Meijie; Fan, Jianming; Li, Baoyun; Li, Liping

2018-04-01

Iron nitrides are considered as highly promising anode materials for lithium-ion batteries because of their nontoxicity, high abundance, low cost, and higher electrical conductivity. Unfortunately, their limited synthesis routes are available and practical application is still hindered by their fast capacity decay. Herein, a facile and green route is developed to synthesize Fe4N/Fe2O3/Fe/porous N-doped carbon nanosheet composite. The size of Fe4N/Fe2O3/Fe particles is small (10-40 nm) and they are confined in porous N-doped carbon nanosheet. These features are conducive to accommodate volume change well, shorten the diffusion distance and further elevate electrical conductivity. When tested as anode material for lithium-ion batteries, a high discharge capacity of 554 mA h g-1 after 100 cycles at 100 mA g-1 and 389 mA h g-1 after 300 cycles at 1000 mA g-1 are retained. Even at 2000 mA g-1, a high capacity of 330 mA h g-1 can be achieved, demonstrating superior cycling stability and rate performance. New prospects will be brought by this work for the synthesis and the potential application of iron nitrides materials as an anode for LIBs.

Decoration of carbon nanotube with size-controlled L10-FePt nanoparticles for storage media

Science.gov (United States)

Moradi, Reza; Sebt, Seyed Ali; Arabi, Hadi; Larijani, Majid Mojtahedzadeh

2013-10-01

In this work, first multi-wall carbon nanotubes (MWCNTs) with outer diameter about 20-30 nm are synthesized by a CVD method; they have been purified and functionalized with a two-step process. The approach consists of thermal oxidation and subsequent chemical oxidation. Then, monosize FePt nanoparticles along carbon nanotubes surface are synthesized by a Polyol process. The synthesized FePt nanoparticles are about 2.5 nm in size and they have superparamagnetic behavior with fcc structure. The CNTs surfaces as a substrate prevent the coalescence of particles during thermal annealing. Annealing at the temperature higher than 600 ∘C for 2 h under a reducing atmosphere (90 % Ar + 10 % H2) leads to phase transition from fcc to fct-L10 structure. So, the magnetic behavior changes from the superparamagnetic to the ferromagnetic. Furthermore, after the phase transition, the FePt nanoparticles have finite size with an average of about 3.5 nm and the coercivity of particles reaches 5.1 kOe.

40 CFR Table 10 to Subpart Uuu of... - Continuous Monitoring Systems for Organic HAP Emissions From Catalytic Cracking Units

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Monitoring Systems for Organic HAP Emissions From Catalytic Cracking Units 10 Table 10 to Subpart UUU of Part 63 Protection of... Organic HAP Emissions From Catalytic Cracking Units As stated in § 63.1565(b)(1), you shall meet each...

75 FR 2831 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, and MD-10-10F...

Science.gov (United States)

2010-01-19

...-0043; Directorate Identifier 2009-NM-128-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas... directive (AD) for certain McDonnell Douglas Model DC-10-10, DC-10-10F, and MD-10-10F airplanes. This... adding the following new AD: McDonnell Douglas Corporation: Docket No. FAA-2010-0043; Directorate...

Disordered crystal structure of 20H-AlON, Al10O3N8

International Nuclear Information System (INIS)

Banno, Hiroki; Funahashi, Shiro; Asaka, Toru; Hirosaki, Naoto; Fukuda, Koichiro

2015-01-01

The disordered crystal structure of 20H-AlON (Al 10 O 3 N 8 ) was determined by combined use of X-ray powder diffraction and transmission electron microscopy. The title compound is hexagonal with space group P6 3 /mmc (Z=2) and the unit-cell dimensions are a=0.307082(5) nm, c=5.29447(8) nm and V=0.432376(12) nm 3 . The structural model showed the positional disordering of three of the six Al sites in the unit cell. The reliability indices calculated from the Rietveld method were R wp =6.97%, S (=R wp /R e )=1.68, R p =5.45%, R B =5.13% and R F =4.56%. We interpreted the disordered structure of 20H-AlON as a statistical average of six different types of ordered structural configurations, which are composed of an octahedral [Al(O, N) 6 ] layer and tetrahedral [Al(O, N) 4 ] layers. We demonstrated the high correlations between the hexagonal unit-cell dimensions and the octahedral layer concentrations for AlON and SiAlON polytypoids. - Graphical abstract: Variations of a and c/(n O +n T ) with n O /(n O +n T ). The a and c are the hexagonal unit-cell dimensions of AlON, SiAlON and AlN. The n O and n T are, respectively, the numbers of octahedral and tetrahedral layers in the unit cells. The unit-cell dimensions in literature are plotted in black plus for AlON and black cross for SiAlON. The unit-cell dimensions of AlN are a=0.3110 nm and c=0.4980 nm. - Highlights: • Crystal structure of Al10O3N8 is determined by laboratory X-ray powder diffraction. • The atom arrangements are represented by the split-atom model. • Six types of ordered atom arrangements are derived from the disordered structure. • Hexagonal unit-cell dimensions changed systematically for AlON and SiAlON compounds

A Radix-10 Digit-Recurrence Division Unit: Algorithm and Architecture

DEFF Research Database (Denmark)

Lang, Tomas; Nannarelli, Alberto

2007-01-01

In this work, we present a radix-10 division unit that is based on the digit-recurrence algorithm. The previous decimal division designs do not include recent developments in the theory and practice of this type of algorithm, which were developed for radix-2^k dividers. In addition to the adaptat...... dynamic range of significant) and it has a shorter latency than a radix-10 unit based on the Newton-Raphson approximation....

40 CFR 22.10 - Appearances.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Appearances. 22.10 Section 22.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL CONSOLIDATED RULES OF PRACTICE GOVERNING... and ethics required of practitioners before the courts of the United States. ...

Room temperature luminescence and ferromagnetism of AlN:Fe

Energy Technology Data Exchange (ETDEWEB)

Li, H., E-mail: lihui@mail.iee.ac.cn, E-mail: wjwang@aphy.iphy.ac.cn [The Key Laboratory of Solar Thermal Energy and Photovoltaic System, Institute of Electrical engineering, Chinese Academy of Sciences, Beijing 100190 (China); Cai, G. M. [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China); Wang, W. J., E-mail: lihui@mail.iee.ac.cn, E-mail: wjwang@aphy.iphy.ac.cn [Research and Development Center for Functional Crystals, Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

2016-06-15

AlN:Fe polycrystalline powders were synthesized by a modified solid state reaction (MSSR) method. Powder X-ray diffraction and transmission electron microscopy results reveal the single phase nature of the doped samples. In the doped AlN samples, Fe is in Fe{sup 2+} state. Room temperature ferromagnetic behavior is observed in AlN:Fe samples. Two photoluminescence peaks located at about 592 nm (2.09 eV) and 598 nm (2.07 eV) are observed in AlN:Fe samples. Our results suggest that AlN:Fe is a potential material for applications in spintronics and high power laser devices.

75 FR 23571 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

Science.gov (United States)

2010-05-04

... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10... amends Sec. 39.13 by adding the following new AD: 2010-09-12 McDonnell Douglas Corporation: Amendment 39... to McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A...

Communication of nuclear data progress: No.10 (1993)

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-12-01

Communication of Nuclear Data Progress (CNDP) is set up by Chinese Nuclear Data Center. This is the tenth issue. It includes the measurements of {sup 54}Fe(d,{alpha}), {sup 56}Fe(d,2n), {sup 58}Ni(d,{alpha}), (d,{alpha}n), (d,x){sup 57}Ni, {sup 182{approx}184}W(d,2n), {sup 186}W(d,p), (d 2n) and {sup 58}Ni(n,{alpha}) reactions; theoretical calculations on n + {sup 16}O and {sup 197}Au, {sup 10}B(n,n) and (n,n`) reactions, channel theory of fission with diffusive dynamics; the evaluations of intermediate energy nuclear data for {sup 56}Fe, {sup 63}Cu, {sup 65}Cu(p,n) monitor reactions, and of {sup 180}Hf, {sup 181}Ta(n,2n) reactions, revision on recommended data of {sup 235}U and {sup 238}U for CENDL-2, fission barrier parameters sublibrary, a PC software of EXFOR compilation, some reports on atomic and molecular data and covariance research.

Emergency Contraceptive Pills: A 10-Year Follow-up Survey of Use and Experiences at College Health Centers in the Mid-Atlantic United States

Science.gov (United States)

Miller, Laura McKeller; Sawyer, Robin G.

2006-01-01

The authors conducted a 10-year follow-up study using a telephone survey to investigate the availability of emergency contraceptive pills (ECPs) at college health centers in the mid-Atlantic region of the United States. They also examined related issues, such as distribution procedure, existence of a written protocol, personnel involved,…

77 FR 6772 - United States Standards for Grades of Cauliflower

Science.gov (United States)

2012-02-09

... Service [Doc. AMS-FV-10-0047] United States Standards for Grades of Cauliflower AGENCY: Agricultural... Standards for Grades of Cauliflower. AMS is reviewing all fresh fruit and vegetable grade standards for... provisions for grading purple, orange or green cauliflower. The proposed revision will amend the color...

Ancient Chemistry "Pharaoh's Snakes" for Efficient Fe-/N-Doped Carbon Electrocatalysts.

Science.gov (United States)

Ren, Guangyuan; Gao, Liangliang; Teng, Chao; Li, Yunan; Yang, Hequn; Shui, Jianglan; Lu, Xianyong; Zhu, Ying; Dai, Liming

2018-04-04

The method of fabricating nonprecious metal electrocatalysts with high activity and durability through a facile and eco-friendly procedure is of great significance to the development of low-cost fuel cells and metal-air batteries. Herein, we present that an ancient chemical reaction of "Pharaoh's snakes" can be a fast and convenient technique to prepare Fe-/N-doped carbon (Fe/N-C) nanosheet/nanotube electrocatalysts with sugar, soda, melamine, and iron nitrate as precursors. The resultant Fe/N-C catalyst has a hierarchically porous structure, a large surface area, and uniformly distributed active sites. The catalyst shows high electrocatalytic activities toward both the oxygen reduction reaction with a half-wave potential of 0.90 V (vs reversible hydrogen electrode) better than that of Pt/C and the oxygen evolution reaction with an overpotential of 0.46 V at the current density of 10 mA cm -2 comparable to that of RuO 2 . The activity and stability of the catalyst are also evaluated in primary and rechargeable Zn-air batteries. In both conditions, three-dimensional Fe/N-C exhibited performances superior to Pt/C. Our work demonstrates a success of utilizing an ancient science to make a state-of-the-art electrocatalyst.

Behavior of methyl orange and orange 10 (orange G) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe

International Nuclear Information System (INIS)

Cruz N, G.

2015-01-01

This work is focused on studying the sorption capacity of methyl orange dye (Nm) and orange 10 (N-10) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe uncalcined and calcined previously at 500 degrees Celsius. Sorption isotherms were determined and the study of the kinetics of sorption was performed. The materials were characterized before and after sorption processes of these dyes by X-ray diffraction, scanning electron microscopy, the specific surface area determination by the Brunauer-Emmett-Teller method, thermogravimetry coupled to mass and infrared spectrometry. The hydrotalcite type compounds reported in this paper were prepared in the laboratory and their acronyms are: HTMgAlG1, HTMgAlMO, HTMgFeG1 and HTMgFeG2. Note that in this work the best conditions for preparing compounds of Mg/Fe were found. From patterns of X-ray diffraction was identified the typical crystal structure of the hydrotalcite type compounds. By scanning electron microscopy the morphology could be determined in the form of flakes characteristics of these compounds. Likewise with elemental analysis of energy dispersive X-ray spectroscopy the presence of Mg, Al, Fe and C, elements of interest for this study was determined. The compounds presented a specific surface area relatively high from 80 to 120 m 2 /g. Thermogravimetry results presented spectra of mass loss very characteristic associated to water losses, dehydroxylation and decarboxylation. The characteristic bands of water and carbonate were assigned by infrared spectroscopy and the bands corresponding to the dyes sulfonates were identified only for the calcined materials. The sorption capacities found of these compounds were as follows: for Nm in the compound HTMgAlG1 uncalcined was 17.82 mg/g for an initial concentration of 200 mg/L and for calcined (HTMgAlMOcal) of 99.8 mg/g with and initial concentration of 1000 mg/L. Moreover, the sorption capacity of the dye N-10 in this same material was 17.92 mg/g and 99.4 mg

Extreme Field Sensitivity of Magnetic Tunneling in Fe-Doped Li_{3}N.

Science.gov (United States)

Fix, M; Atkinson, J H; Canfield, P C; Del Barco, E; Jesche, A

2018-04-06

The magnetic properties of dilute Li_{2}(Li_{1-x}Fe_{x})N with x∼0.001 are dominated by the spin of single, isolated Fe atoms. Below T=10  K the spin-relaxation times become temperature independent indicating a crossover from thermal excitations to the quantum tunneling regime. We report on a strong increase of the spin-flip probability in transverse magnetic fields that proves the resonant character of this tunneling process. Longitudinal fields, on the other hand, lift the ground-state degeneracy and destroy the tunneling condition. An increase of the relaxation time by 4 orders of magnitude in applied fields of only a few milliTesla reveals exceptionally sharp tunneling resonances. Li_{2}(Li_{1-x}Fe_{x})N represents a comparatively simple and clean model system that opens the possibility to study quantum tunneling of the magnetization at liquid helium temperatures.

30 CFR 902.10 - State regulatory program approval.

Science.gov (United States)

2010-07-01

... Mining and Water Management, 3601 C Street, Suite 800, Anchorage, AK 99503-5925, Telephone: (907) 762... Section 902.10 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE ALASKA § 902.10 State...

7 CFR 1212.31 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1212.31 Section 1212.31 Agriculture..., Consumer Education, and Industry Information Order Definitions § 1212.31 United States. “United States... territories and possessions of the United States. ...

Room temperature luminescence and ferromagnetism of AlN:Fe

Directory of Open Access Journals (Sweden)

H. Li

2016-06-01

Full Text Available AlN:Fe polycrystalline powders were synthesized by a modified solid state reaction (MSSR method. Powder X-ray diffraction and transmission electron microscopy results reveal the single phase nature of the doped samples. In the doped AlN samples, Fe is in Fe2+ state. Room temperature ferromagnetic behavior is observed in AlN:Fe samples. Two photoluminescence peaks located at about 592 nm (2.09 eV and 598 nm (2.07 eV are observed in AlN:Fe samples. Our results suggest that AlN:Fe is a potential material for applications in spintronics and high power laser devices.

7 CFR 1250.308 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1250.308 Section 1250.308 Agriculture... Research and Promotion Order Definitions § 1250.308 United States. United States means the 48 contiguous States of the United States of America and the District of Columbia. ...

7 CFR 1205.23 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1205.23 Section 1205.23 Agriculture... Procedures for Conduct of Sign-up Period Definitions § 1205.23 United States. The term United States means the 50 states of the United States of America. Procedures ...

19 CFR 10.411 - Certification of origin or other information.

Science.gov (United States)

2010-04-01

... Free Trade Agreement Import Requirements § 10.411 Certification of origin or other information. (a... the United States-Chile Free Trade Agreement; there has been no further production or any other... regional value content or other requirements specified in General Note 26(n), HTSUS; (3) Preference...

7 CFR 1219.26 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1219.26 Section 1219.26 Agriculture..., AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.26 United States. United States means collectively the several 50 States of the United States, the District of...

75 FR 38943 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-30, DC...

Science.gov (United States)

2010-07-07

...-0672; Directorate Identifier 2010-NM-047-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas...: McDonnell Douglas Corporation: Docket No. FAA-2010-0672; Directorate Identifier 2010-NM-047-AD. Comments Due... applies to McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-30, DC-10-30F (KDC-10), DC-10...

10. State energy balance - 1978-1991

International Nuclear Information System (INIS)

1993-12-01

The energetic matrix of Minas Gerais State (Brazil) for the year 1991 and historic review of 1978 to 1990 are shown in this 10. State Energy Balance. The global balance and the state structure of energy demand, by energy source and socio-economic sector are presented, and the relations between energy system and the Minas Gerais economic performance are analysed. The consumption evolution by sector is also cited. (C.G.C.)

75 FR 6160 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

Science.gov (United States)

2010-02-08

...-0032; Directorate Identifier 2009-NM-213-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas...: McDonnell Douglas Corporation: Docket No. FAA-2010-0032; Directorate Identifier 2009-NM-213-AD. Comments Due... applies to McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A...

Atomistic modeling of L10 FePt: path to HAMR 5Tb/in2

Science.gov (United States)

Chen, Tianran; Benakli, Mourad; Rea, Chris

2015-03-01

Heat assisted magnetic recording (HAMR) is a promising approach for increasing the storage density of hard disk drives. To increase data density, information must be written in small grains, which requires materials with high anisotropy energy such as L10 FePt. On the other hand, high anisotropy implies high coercivity, making it difficult to write the data with existing recording heads. This issue can be overcome by the technique of HAMR, where a laser is used to heat the recording medium to reduce its coercivity while retaining good thermal stability at room temperature due to the large anisotropy energy. One of the keys to the success of HAMR is the precise control of writing process. In this talk, I will propose a Monte Carlo simulation, based on an atomistic model, that would allow us to study the magnetic properties of L10 FePt and dynamics of spin reversal for the writing process in HAMR.

7 CFR 1215.20 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1215.20 Section 1215.20 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... United States. United States means all of the States. Popcorn Board ...

75 FR 63040 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-30, DC...

Science.gov (United States)

2010-10-14

... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-30, DC-10-30F (KDC-10... following new airworthiness directive (AD): 2010-21-13 McDonnell Douglas Corporation: Amendment 39-16473... November 18, 2010. Affected ADs (b) None. Applicability (c) This AD applies to McDonnell Douglas...

Effect of 1.0% Ni on high-temperature impression creep and hardness of recycled aluminium alloy with high Fe content

Science.gov (United States)

Faisal, M.; Mazni, Noor; Prasada Rao, A. K.

2018-03-01

Reported work focusses on the effect of 1.0% Ni addition on the microstructure, high- temperature impression creep and thereby the hardness of recycled Al-alloy containing >2wt% Fe, obtained from automotive scrap. Present studies have shown that the addition of 1.0% Ni have supress the formation of α-phase (Al5FeSi) by supressing the peritectic transformation of β-phase (Al8Fe2Si). Such suppression is found to improve the hardness and high-temperature impression creep of the recycled aluminium alloy.

Investigations on FCAM-III (Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36): A new homologue of the aenigmatite structure-type in the system CaO-MgO-Fe2O3-Al2O3

Science.gov (United States)

Zöll, Klaus; Kahlenberg, Volker; Krüger, Hannes; Tropper, Peter

2018-02-01

In the course of a systematic study of a part of the quaternary system Fe2O3-CaO-Al2O3-MgO (FCAM) the previously unknown compound Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 (FCAM-III) has been synthesized. By analogy with the so-called SFCA series [1-5], our investigation in the system of FCAM shows the existence of a stoichiometric homologous series M14+6nO20+8n, where M = Fe, Ca, Al, Mg and n = 1 or 2. In air, we can prove the formation of coexisting FCAM-III and FCAM-I solid solutions at 1400 °C. By increasing the temperature up to 1425 °C FCAM-I disappears completely and FCAM-III co-exists with magnesiumferrite and a variety of calcium iron oxides. At 1450 °C FCAM-III breaks down to a mixture of FCAM-I again as well as magnesioferrite and melt. Small single-crystals of FCAM-III up to 35 μm in size could be retrieved from the 1425 °C experiment and were subsequently characterized using electron microprobe analysis and synchroton X-ray single-crystal diffraction. Finally the Fe2+/Fetot ratio was calculated from the total iron content based on the crystal-chemical formula obtained from EMPA measurements and charge balance considerations. FCAM-III or Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 has a triclinic crystal structure (space group P 1 ̅). The basic crystallographic data are: a = 10.223(22) Å, b = 10.316(21) Å, c = 14.203(15) Å, α = 93.473(50)°, β = 107.418(67)°, γ = 109.646(60)°, V = 1323.85(2) ų, Z = 1. Using Schreinemaker's technique to analyze the phase relations in the system Fe2O3-CaO-Al2O3-MgO it was possible to obtain the semi-quantitative stability relations between the participating phases and construct a topologically correct phase sequence as a function of T and fO2. The analysis shows that Ca2Al0.5Fe1.5O5 (C2A0.25F0.75) and CaAl1.5Fe2.5O7 (CA0.75F1.25) with higher calculated Fe2+ contents are preferably formed at lower oxygen fugacity and react to CaAl0.5Fe1.5O4 (CA0.25F0.75) by increasing fO2. Spinel-type magnesium

7 CFR 1206.23 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1206.23 Section 1206.23 Agriculture... INFORMATION Mango Promotion, Research, and Information Order Definitions § 1206.23 United States. United... Rico, and the territories and possessions of the United States. ...

76 FR 78805 - Regulatory Changes To Implement the United States/Australian Agreement for Peaceful Nuclear...

Science.gov (United States)

2011-12-20

... Implement the United States/Australian Agreement for Peaceful Nuclear Cooperation; Corrections AGENCY... the Government of Australia and the Government of the United States of America Concerning Peaceful... action is unnecessary. List of Subjects in 10 CFR Part 40 Criminal penalties, Government contracts...

75 FR 60602 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

Science.gov (United States)

2010-10-01

... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10... adding the following new AD: 2010-20-14 McDonnell Douglas Corporation: Amendment 39-16449. Docket No. FAA... the airplanes identified in paragraphs (c)(1) and (c)(2) of this AD. (1) McDonnell Douglas Corporation...

New Mexico HUC-10 Boundaries - 2013

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This data set is a complete digital hydrologic unit boundary layer to the watershed (10-digit) 10th level for the State of New Mexico. This data set consists of...

39 CFR 10.2 - Advisory service.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Advisory service. 10.2 Section 10.2 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE RULES OF CONDUCT FOR POSTAL SERVICE GOVERNORS (ARTICLE X) § 10.2 Advisory service. (a) The General Counsel is the Ethical...

32 CFR 705.10 - Still photography.

Science.gov (United States)

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Still photography. 705.10 Section 705.10 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS PUBLIC AFFAIRS REGULATIONS § 705.10 Still photography. (a) Policy and procedures on taking photos by the general public, given in ...

7 CFR 1280.127 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1280.127 Section 1280.127 Agriculture... INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.127 United States. United States means collectively the 50 States and the District of Columbia. ...

45 CFR 212.7 - Repayment to the United States.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false Repayment to the United States. 212.7 Section 212... UNITED STATES CITIZENS RETURNED FROM FOREIGN COUNTRIES § 212.7 Repayment to the United States. (a) An..., any or all of the cost of such assistance to the United States, except insofar as it is determined...

Doping effect on the physical properties of Ca10Pt3As8(Fe2As2)5 single crystals

Science.gov (United States)

Pan, Jiayun; Karki, Amar; Plummer, E. W.; Jin, Rongying

2017-12-01

Ca10Pt3As8(Fe2As2)5 is a unique parent compound for superconductivity, which consists of both semiconducting Pt3As8 and metallic FeAs layers. We report the observation of superconductivity induced via chemical doping in either Ca site using rare-earth (RE) elements (RE  =  La, Gd) or Fe site using Pt. The interlayer distance and the normal-state physical properties of the doped system change correspondingly. The coupled changes include (1) superconducting transition temperature T c increases with increasing both doping concentration and interlayer distance, (2) our T c value is higher than previously reported maximum value for Pt doping in the Fe site, (3) both the normal-state in-plane resistivity and out-of-plane resistivity change from non-metallic to metallic behavior with increasing doping concentration and T c, and (4) the transverse in-plane magnetoresistance (MRab) changes from linear-field dependence to quadratic behavior upon increasing T c. For La-doped compound with the highest T c (~35 K), upper critical fields (Hc2ab , Hc2c ), coherence lengths (ξ ab, ξ c), and in-plane penetration depth (λ ab) are estimated. We discuss the relationship between chemical doping, interlayer distance, and physical properties in this system.

Strength of 10CR-N martensitic steels

International Nuclear Information System (INIS)

Bahrami, F.; Hendry, A.

1993-01-01

10Cr stainless steel has been employed to examine the effect of nitrogen on microstructure and strength. Applying Solid state gaseous nitrogenising treatments a whole range of nitrogen martensite structures containing up to 0.45 wt% were obtained. It was found that a linear relationship exists between strength and nitrogen content in precipitate free martensitic structures. Yield strength increased from 705 to 1295 MPa for nitrogen free base material and alloys with 0.35 wt%N respectively. Pronounce secondary hardening was observed at a tempering temperature of 500 C. A linear relationship was also observed between the lattice parameter and nitrogen concentration in these alloys. A model for mechanical behaviour is presented. (orig.)

Muon capture by the 1p shell of 10B, 12C and 14N nuclei. Experiments and interpretation

International Nuclear Information System (INIS)

Moura Goncalves, A.C. de.

1980-12-01

The main elements necessary to treat weak interactions in a nucleus including the contributions of exchange meson currents are presented. The case of a transition between an initial (Z,A) nucleus and a final (Z-1,A) nucleus in a well defined bound state is treated. The form of the single body operator taking into account the nucleonic degrees of freedom (impulse approximation) is recalled. The construction of a two-body operator taking mesonic degrees of freedom into account is outlined. Measurements of partial capture rates in 10 B, 12 C and 14 N target nuclei leading to excited bound states of 10 Be, 12 B and 14 C residual nuclei are described. Results are given and comparisons made with the calculations performed, nuclear states being described by various wave functions. Measurements of the polarization of the 1 + ground state of 12 B after N capture in 12 C are briefly described. An attempt is made to interpret the 0 + 1 + transition occurring in the A = 12 triad. A convenient parametrization is obtained from the expression for these observable quantities as a function of the nuclear shape factors. This analysis enables a strict choice to be made from the available wavefunctions. It demonstrates that experimental data are well reproduced by the microscopy approach performed using the effective Sussex potential and single pion exchange currents. Finally, the hitherto unexplored domain of muon capture is tackled. A high energy transfer is involved in which the neutrino remains practically at rest. In this case, the vector part is not very important and the axial current time part contributes as much is the space part. The (μ - ,pn) reaction was used for exploratory measurements in this domain. Practical limits are determined [fr

Hydrogen bonded networks in formamide [HCONH2]n (n = 1 – 10 ...

Indian Academy of Sciences (India)

gns

Table S1: Comparison of interaction energy (I.E) in kcal/mol in four arrangements of formamide n=1-10 at B3LYP/D95** level of theory. n = #monomers. Table S2: O---H bond length (in Å) for formamide clusters n = (2-10). Table S3: N-H bond stretching frequency (in cm-1) for four arrangements of formamide clusters n.

Preparation and properties of [(NdFeB)x/(Nb)z]n multi-layer films

International Nuclear Information System (INIS)

Tsai, J.-L.; Chin, T.-S.; Yao, Y.-D.; Melsheimer, A.; Fisher, S.; Drogen, T.; Kelsch, M.; Kronmueller, H.

2003-01-01

Multi-layer [(NdFeB) x /(Nb) z ] n films with 200 nm≥x≥10 nm, 10 nm≥z≥0, 40≥n≥2, prepared by ion beam sputtering and subsequent annealing, show significantly enhanced coercivity due to the reduced grain size that enhances the anisotropy of individual grains. After annealing at 630 deg. C, some Nd 2 Fe 14 B grains were enriched with Nb and isolated as the thickness of the Nb spacer layer increases. For multi-layer (NdFeB x /Nb z ) n films with 100 nm ≥x≥25 nm, 5 nm≥z≥2 nm, their coercivity and remanence ratio are better than that of a single NdFeB film. Up to 17.8 kOe room temperature coercivity has been obtained for a sample with x=25 nm, z=5 nm and n=16

Enhanced photocatalytic property of BiFeO_3/N-doped graphene composites and mechanism insight

International Nuclear Information System (INIS)

Li, Pai; Li, Lei; Xu, Maji; Chen, Qiang; He, Yunbin

2017-01-01

Highlights: • A hydrothermal process was used to prepare BiFeO_3/N-doped graphene composites. • BiFeO_3/N-doped graphene exhibits superior photocatalytic activity and stability. • The energy band of BiFeO_3 bends downward by ∼1.0 eV at the composite interface. • Downward band bending leads to rapid electron transfer at the composite interface. • Holes and ·OH are predominant active species in the photo-degradation process. - Abstract: A series of BiFeO_3/(N-doped) graphene composites are prepared by a facile hydrothermal method. BiFeO_3/N-doped graphene shows photocatalytic performance superior to that of BiFeO_3/graphene and pristine BiFeO_3. The enhanced photo-degradation performance of BiFeO_3/N-doped graphene are mainly attributable to the improved light absorbance of the composite, abundant active adsorption sites and high electrical charge mobility of N-doped graphene, and the downward band bending of BiFeO_3 at the composite interface. In particular, X-ray photoelectron spectroscopy analyses reveal that the electron energy band of BiFeO_3 is downward bent by 1.0 eV at the interface of BiFeO_3/N-doped graphene, because of different work functions of both materials. This downward band bending facilitates the transfer of photogenerated electrons from BiFeO_3 to N-doped graphene and prompts the separation of photo-generated electron-hole pairs, leading eventually to the enhanced photocatalytic performance.

7 CFR 1260.108 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1260.108 Section 1260.108 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Promotion and Research Order Definitions § 1260.108 United States. United States means the 50 States and the...

7 CFR 1221.32 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1221.32 Section 1221.32 Agriculture... INFORMATION ORDER Sorghum Promotion, Research, and Information Order Definitions § 1221.32 United States. United States or U.S. means collectively the 50 States, the District of Columbia, the Commonwealth of...

7 CFR 1216.30 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1216.30 Section 1216.30 Agriculture... INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.30 United States. United States means collectively the 50 states, the District of Columbia, the Commonwealth of Puerto Rico...

7 CFR 1218.22 - United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States. 1218.22 Section 1218.22 Agriculture... INFORMATION ORDER Blueberry Promotion, Research, and Information Order Definitions § 1218.22 United States. United States means collectively the 50 states, the District of Columbia, the Commonwealth of Puerto Rico...

75 FR 68246 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

Science.gov (United States)

2010-11-05

...-1044; Directorate Identifier 2010-NM-033-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas..., 2007) and adding the following new AD: McDonnell Douglas Corporation: Docket No. FAA-2010-1044.... Applicability (c) This AD applies to all McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

Bis(1,10-phenanthroline-κ2N,N′(sulfato-κOcopper(II ethanol monosolvate

Directory of Open Access Journals (Sweden)

Natthaya Meundaeng

2013-10-01

Full Text Available The crystal structure of the title compound, [Cu(SO4(C12H8N22]·C2H5OH, arises from the assembly of the neutral complex [Cu(SO4(C12H8N22] and an ethanol solvent molecule. The CuII ion is five-coordinate, surrounded by two pairs of N atoms from two independent N,N′-chelating 1,10-phenanthroline ligands, and one O atom of monodentate sulfate ligand, in a distorted trigonal-bipyramidal fashion. Spatial orientation of the ligands and the assembly in the solid state are stabilized by the C—H...O hydrogen-bonding interactions, established between the O atoms (from the sulfate ligand and the ethanol molecule and the neighbouring 1,10-phenanthroline molecules. There is also an offset face-to-face π–π stacking between the 1,10-phenanthroline ligands. The ethanol solvent molecule is disordered over two orientations in the ratio 0.663 (10:0.337 (10. The crystal examined was subject to racemic twinning and the refined twin fraction was 0.346 (19.

19 CFR 212.10 - Contents of application.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 3 2010-04-01 2010-04-01 false Contents of application. 212.10 Section 212.10 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE IMPLEMENTATION OF THE EQUAL ACCESS TO JUSTICE ACT Information Required From Applicants § 212.10...

26 CFR 1.936-10 - Qualified investments.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 10 2010-04-01 2010-04-01 false Qualified investments. 1.936-10 Section 1.936... (CONTINUED) INCOME TAXES Possessions of the United States § 1.936-10 Qualified investments. (a) In general. [Reserved] (b) Qualified investments in Puerto Rico. [Reserved] (c) Qualified investment in certain...

Magnetic properties of Co 2 2+ Co 1 - x 3+ Fe x 3+ BO5 ( x = 0.10) single crystals with a ludwigite structure

Science.gov (United States)

Knyazev, Yu. V.; Kazak, N. V.; Bayukov, O. A.; Platunov, M. S.; Velikanov, D. A.; Bezmaternykh, L. N.; Ivanova, N. B.; Ovchinnikov, S. G.

2017-04-01

The investigation of mixed Co-Fe ludwigite single crystals shows that their magnetic properties are close to the magnetic properties of Fe3BO5 despite the predominance of cobalt ions. The magnetic properties of Co3 - x Fe x BO5 single crystals with x = 0.10 are studied in detail. Magnetometric measurements demonstrate a strong magnetic anisotropy with easy magnetization axis b, and the orbital magnetic moment of cobalt is in a frozen state. The detected temperature dependence of the absorption of Mössbauer spectra allowed us to determine the magnetic ordering temperature, which agrees with the results of magnetization measurements ( T C = 84 K).

Microstructure and magnetocaloric effect in cast LaFe11.5Si1.5Bx (x=0.5, 1.0)

International Nuclear Information System (INIS)

Zhang, H.; Long, Y.; Cao, Q.; Mudryk, Ya.; Zou, M.; Gschneidner, K.A.; Pecharsky, V.K.

2010-01-01

Phase formation, structure, and the magnetocaloric effect (MCE) in as-cast LaFe 11.5 Si 1.5 B x (x=0.5, 1.0) compounds have been studied. The Curie temperatures, T C , are ∼211 and 230 K for x=0.5 and 1.0, respectively, which are higher than that of annealed LaFe 11.5 Si 1.5 (T C =183 K), while the maximum magnetic entropy changes at the respective T C under a magnetic field change of 0-5 T are 7.8 and 5.8 J/(kg K). Wavelength dispersive spectrometry (WDS) analysis shows that only a small fraction of boron atoms is dissolved in the NaZn 13 -type structure phase, and that the compositions of the as-cast LaFe 11.5 Si 1.5 B x (x=0.5, 1.0) alloys are much different from the intended nominal compositions. These as-cast alloys exhibit second-order magnetic phase transitions and low MCEs. However, based on the relative cooling power, the as-cast LaFe 11.5 Si 1.5 B x alloys are promising candidates for magnetic refrigerants over a wide temperature range.

Thermal stability of ultrasoft Fe-Zr-N films

NARCIS (Netherlands)

Chechenin, NG; van Veen, A; Schut, H; Chezan, AR; Boerma, D; Vystavel, T; De Hosson, JTM

2003-01-01

The thermal stability of nanocrystalline ultrasoft magnetic (Fe98Zr2)(1-x)N-x films with x = 0.10-0.25 was studied using thermal desorption spectrometry, positron beam analysis and high resolution transmission electron microscopy. The results demonstrate that grain growth during the heat treatment

Magnetic and structural properties of Sr0.75La0.25FexCu0.20O19 (10.40≤x≤11.80) hexagonal ferrites prepared by the solid-state reaction

International Nuclear Information System (INIS)

Yang, Yujie; Shao, Juxiang; Wang, Fanhou; Liu, Xiansong; Feng, Shuangjiu; Huang, Duohui; Yang, Junsheng; Jin, Chengguo

2016-01-01

In this study, the hexaferrite magnetic powders and magnets according to the formula Sr 0.75 La 0.25 Fe x Cu 0.20 O 19 , where x ranging from 10.40 to 11.80 with a step of 0.2 were prepared by the solid-state reaction. X-ray diffraction was performed to investigate the microstructures of the magnetic powders. The results show that a single magnetoplumbite phase is obtained for the magnetic powders with Fe content (10.60≤x≤11.60). For the magnetic powders with Fe content (x) of 10.40 or 11.80, magnetic impurities appear in the structure. A field emission scanning electron microscopy was hired to explore the micrographs of the magnets. The hexaferrite magnets are formed of hexagonal-shaped crystals. A magnetic properties test instrument was used in order to study the magnetic properties of the magnets. The remanence and maximum energy product first increase with Fe content (x) from 10.40 to 11.00 and then begin to decrease when Fe content (x) continues to increase. While the intrinsic coercivity and magnetic induction coercivity first increase with Fe content (x) from 10.40 to 11.20 and then decrease when Fe content (x)>11.20. - Highlights: • The hexaferrite Sr 0.75 La 0.25 Fe x Cu 0.20 O 19 (10.40≤x≤11.80) magnetic powders and magnets were synthesized by the solid-state reaction. • The hexaferrite magnets are formed of hexagonal-shaped crystals. • At Fe content (x)=11.00, B r and (BH) max for the magnets reach the maximum values. At Fe content (x)=11.20, H cj and H cb for the magnets reach the maximum values.

Bis[(cyanido-κCbis(1,10-phenanthroline-κ2N,N′copper(II] pentakis(cyanido-κCnitrosoferrate(II dimethylformamide monosolvate

Directory of Open Access Journals (Sweden)

Olesia V. Kozachuk

2012-09-01

Full Text Available The title compound, [Cu(CN(C12H8N22]2[Fe(CN5(NO]·C3H7NO, is formed of discrete [Cu(phen2CN]+ cations (phen is 1,10-phenanthroline, nitroprusside [Fe(CN5(NO]2− anions and dimethylformamide (DMF molecules of crystallization. The metal atom has a distorted trigonal–bipyramidal coordination environment, defined by four N atoms of two phen molecules and a C atom of the cyanide group (in the equatorial position. The [Fe(CN5(NO]2− anion was found to be disordered about (but not on a crystallographic twofold rotation axis. Geometries were restrained to ideal values. The dimethylformamide solvent molecule was found to be disordered about a crystallographic inversion centre.

Study of microstructure and correlative magnetic property in bulk Fe{sub 61}Nd{sub 10}B{sub 25}Nb{sub 4} permanent magnet

Energy Technology Data Exchange (ETDEWEB)

Man, H.; Xu, H. [Laboratory for Microstructures, Shanghai University, Shanghai 200444 (China); Liu, H.W. [The Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia); Tan, X.H., E-mail: tanxiaohua123@163.com [Laboratory for Microstructures, Shanghai University, Shanghai 200444 (China); Peng, J.C.; Bai, Q. [Laboratory for Microstructures, Shanghai University, Shanghai 200444 (China)

2012-11-01

Highlights: Black-Right-Pointing-Pointer A fully dense bulk Fe{sub 61}Nd{sub 10}B{sub 25}Nb{sub 4} permanent magnet was obtained by the simple process of copper mold casting and subsequent annealed at 943 K. Black-Right-Pointing-Pointer The relationship between microstructures and correlative magnetic property of Fe{sub 61}Nd{sub 10}B{sub 25}Nb{sub 4} alloy was investigated. Black-Right-Pointing-Pointer The high value of intrinsic coercivity of 1191 kA/m was obtained due to the existence of hard magnetic Nd{sub 2}Fe{sub 14}B phase. - Abstract: The correlation between microstructure and magnetic property of a bulk Fe{sub 61}Nd{sub 10}B{sub 25}Nb{sub 4} alloy are investigated. The microstructure of the as-cast Fe{sub 61}Nd{sub 10}B{sub 25}Nb{sub 4} alloy shows a small amount of NbFeB phase with a grain size of 500 nm embedded in an amorphous matrix. The as-cast sample shows soft magnetic behavior at room temperature, after a heat treatment the hard magnetic properties are observed. A fully dense bulk Fe{sub 61}Nd{sub 10}B{sub 25}Nb{sub 4} permanent magnet is obtained with an intrinsic coercivity ({sub i}H{sub c}) of 1191 kA/m and a maximum energy product ((BH){sub max}) of 31.7 kJ/m{sup 3} after annealing at 943 K for 20 min. The corresponding microstructure consists of Nd{sub 2}Fe{sub 14}B, NdFe{sub 4}B{sub 4} and NbFeB phases. The existence of the hard magnetic Nd{sub 2}Fe{sub 14}B phase is the reason resulting in a high value of {sub i}H{sub c}. On the other hand, the influences of NdFe{sub 4}B{sub 4} and NbFeB phases in the annealed specimen on the magnetic properties are also discussed.

Hot Ductility Behaviors in the Weld Heat-Affected Zone of Nitrogen-Alloyed Fe-18Cr-10Mn Austenitic Stainless Steels

Science.gov (United States)

Moon, Joonoh; Lee, Tae-Ho; Hong, Hyun-Uk

2015-04-01

Hot ductility behaviors in the weld heat-affected zone (HAZ) of nitrogen-alloyed Fe-18Cr-10Mn austenitic stainless steels with different nitrogen contents were evaluated through hot tension tests using Gleeble simulator. The results of Gleeble simulations indicated that hot ductility in the HAZs deteriorated due to the formation of δ-ferrite and intergranular Cr2N particles. In addition, the amount of hot ductility degradation was strongly affected by the fraction of δ-ferrite.

Measurement of N and C diffusion in Sm2Fe17 by magnetic relaxation

International Nuclear Information System (INIS)

Mommer, N.; Hirscher, M.; Gerlach, M.; Van Lier, J.; Kronmueller, H.; Kubis, M.; Mueller, K.-H.

1998-01-01

Magnetic after-effect (MAE) measurements of nitrided and carburized Sm 2 Fe 17 compounds were performed in the temperature range of 140 K to 480 K. Both nitrided and carburized compounds show relaxation maxima at 285 and 300 K, respectively, which are absent in pure Sm 2 Fe 17 compounds. Therefore, these relaxation maxima are attributed to jumps of interstitially dissolved nitrogen or carbon atoms. Numerical evaluation yielded an activation enthalpy Q N (0.84±0.05) eV and a pre-exponential factor τ 0 N =3.10 -15±1 s for the short-range diffusion of N atoms. The corresponding values for the carbon diffusion are Q C =(0.91±0.05) eV and τ 0 C =1.10 -15±1 s. The carbon and nitrogen content of the samples was determined from the increase in mass during nitrogenation or carburization to Sm 2 Fe 17 N 1.2 and Sm 2 Fe 17 C 2.6 . (orig.)

Pressure-induced magnetic transition in Fe sub 4 N probed by Fe K-edge XMCD measurement

CERN Document Server

Ishimatsu, N; Maruyama, H; Kawamura, N; Suzuki, M; Ohishi, Y; Ito, M; Nasu, S; Kawakami, T

2003-01-01

X-ray magnetic circular dichroism (XMCD) of gamma'-iron nitride (Fe sub 4 N) was recorded at Fe K-edge under high pressure up to 27 GPa. The XMCD intensity decreased remarkably with pressure, and vanished at 24 GPa. Compressibility was measured by the X-ray diffraction method. These results indicate that Fe sub 4 N undergoes a second-order phase transition from the ferromagnetic state to a paramagnetic state without any structural change. The pressure-induced demagnetizing process is discussed in terms of the Fe magnetic states in the local environment.

Fe3Nb3N precipitates of the Fe3W3C type in Nb stabilized ferritic stainless steel

International Nuclear Information System (INIS)

Malfliet, A.; Van den Broek, W.; Chassagne, F.; Mithieux, J.-D.; Blanpain, B.; Wollants, P.

2011-01-01

Highlights: → The precipitation in Nb stabilized ferritic stainless steel at 950 deg. C is investigated. → We characterized the Fe 3 Nb 3 X precipitates with SAED, EELS, WDS and AES. → We found that Fe 3 Nb 3 X precipitates are stabilized by N and not by C or O. → This insight is new and important for future development of this type of steel grade. - Abstract: A Nb stabilized ferritic stainless steel with 0.45 wt.%Nb, 82 ppm C and 170 ppm N is investigated to reveal the nature of the precipitates present at 950 deg. C. In particular, Fe 3 Nb 3 X precipitates of the Fe 3 W 3 C type are analyzed with WDS and EELS to determine the light elements X stabilizing this phase in the steel. According to WDS on large precipitates after 500 h at 950 deg. C, the Fe 3 Nb 3 X phase contains 10.4 at.% N, 1.2 at.% O and 1.0 at.% C. Auger Electron Spectroscopy on the same precipitates confirms the presence of N. In addition, it is revealed that the C and O peaks observed with WDS result from surface contamination as they disappear after Ar sputtering. The presence of a N peak in the EELS spectra of small Fe 3 Nb 3 X precipitates which have formed after 6 min at 950 deg. C indicate that N stabilizes this phase already from the initial precipitation stage. With this analysis it is demonstrated that N is an effective stabilizer of Fe 3 Nb 3 X precipitates in ferritic stainless steels. The formation of this phase should therefore be considered when predicting the precipitation behavior of Nb in industrial Nb stabilized ferritic stainless steels containing residual N.

1 CFR 5.10 - Forms of publication.

Science.gov (United States)

2010-01-01

... 1 General Provisions 1 2010-01-01 2010-01-01 false Forms of publication. 5.10 Section 5.10 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER THE FEDERAL REGISTER GENERAL § 5.10 Forms of publication. Pursuant to section 1506 of title 44, United States Code, the Administrative Committee publishes...

37 CFR 11.10 - Restrictions on practice in patent matters.

Science.gov (United States)

2010-07-01

... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Restrictions on practice in patent matters. 11.10 Section 11.10 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE REPRESENTATION OF OTHERS BEFORE THE UNITED STATES PATENT AND...

Deep conditions of hydrothermalism of dorsal East Pacific at 130N

International Nuclear Information System (INIS)

Boulegue, J.; Jedwab, J.

1985-01-01

Taking advantage of the formation of carbon graphite and Fe-Zn spinels one can compute the conditions of sea water-basalt interaction in deep conditions at 13 0 N E.P.R. One finds: p=260-500 bar, T=440-480 0 C, fO 2 =10 -27 -10sup(-24.5) bar, pH 2 O/pH 2 approximately= 100, fCO 2 /fCO approximately= 600. These conditions lead to a discussion of the possibilities of vaporisation of the hydrothermal fluid and to a discussion of the geochemical behaviour of U and Fe [fr

Fe/N/C hollow nanospheres by Fe(iii)-dopamine complexation-assisted one-pot doping as nonprecious-metal electrocatalysts for oxygen reduction

Science.gov (United States)

Zhou, Dan; Yang, Liping; Yu, Linghui; Kong, Junhua; Yao, Xiayin; Liu, Wanshuang; Xu, Zhichuan; Lu, Xuehong

2015-01-01

In this work, a series of hollow carbon nanospheres simultaneously doped with N and Fe-containing species are prepared by Fe3+-mediated polymerization of dopamine on SiO2 nanospheres, carbonization and subsequent KOH etching of the SiO2 template. The electrochemical properties of the hollow nanospheres as nonprecious-metal electrocatalysts for oxygen reduction reaction (ORR) are characterized. The results show that the hollow nanospheres with mesoporous N-doped carbon shells of ~10 nm thickness and well-dispersed Fe3O4 nanoparticles prepared by annealing at 750 °C (Fe/N/C HNSs-750) exhibit remarkable ORR catalytic activity comparable to that of a commercial 20 wt% Pt/C catalyst, and high selectivity towards 4-electron reduction of O2 to H2O. Moreover, it displays better electrochemical durability and tolerance to methanol crossover effect in an alkaline medium than the Pt/C. The excellent catalytic performance of Fe/N/C HNSs-750 towards ORR can be ascribed to their high specific surface area, mesoporous morphology, homogeneous distribution of abundant active sites, high pyridinic nitrogen content, graphitic nitrogen and graphitic carbon, as well as the synergistic effect of nitrogen and iron species for catalyzing ORR.In this work, a series of hollow carbon nanospheres simultaneously doped with N and Fe-containing species are prepared by Fe3+-mediated polymerization of dopamine on SiO2 nanospheres, carbonization and subsequent KOH etching of the SiO2 template. The electrochemical properties of the hollow nanospheres as nonprecious-metal electrocatalysts for oxygen reduction reaction (ORR) are characterized. The results show that the hollow nanospheres with mesoporous N-doped carbon shells of ~10 nm thickness and well-dispersed Fe3O4 nanoparticles prepared by annealing at 750 °C (Fe/N/C HNSs-750) exhibit remarkable ORR catalytic activity comparable to that of a commercial 20 wt% Pt/C catalyst, and high selectivity towards 4-electron reduction of O2 to H2O

39 CFR 10.3 - Post-employment activities.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Post-employment activities. 10.3 Section 10.3 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE RULES OF CONDUCT FOR POSTAL SERVICE GOVERNORS (ARTICLE X) § 10.3 Post-employment activities. Governors are subject...

Enhancement of L10 ordering with the c-axis perpendicular to the substrate in FePt alloy film by using an epitaxial cap-layer

Directory of Open Access Journals (Sweden)

Mitsuru Ohtake

2017-05-01

Full Text Available FePt alloy thin films with cap-layers of MgO or C are prepared on MgO(001 single-crystal substrates by using a two-step method consisting of low-temperature deposition at 200 °C followed by high-temperature annealing at 600 °C. The FePt film thickness is fixed at 10 nm, whereas the cap-layer thickness is varied from 1 to 10 nm. The influences of cap-layer material and cap-layer thickness on the variant structure and the L10 ordering are investigated. Single-crystal FePt(001 films with disordered fcc structure (A1 grow epitaxially on the substrates at 200 °C. Single-crystal MgO(001 cap-layers grow epitaxially on the FePt films, whereas the structure of C cap-layers is amorphous. The phase transformation from A1 to L10 occurs when the films are annealed at 600 °C. The FePt films with MgO cap-layers thicker than 2 nm consist of L10(001 variant with the c-axis perpendicular to the substrate surface, whereas those with C cap-layers involve small volumes of L10(100 and (010 variants with the c-axis lying in the film plane. The in-plane and the out-of-plane lattices are respectively more expanded and contracted in the continuous-lattice MgO/FePt/MgO structure due to accommodations of misfits of FePt film with respect to not only the MgO substrate but also the MgO cap-layer. The lattice deformation promotes phase transformation along the perpendicular direction and L10 ordering. The FePt films consisting of only L10(001 variant show strong perpendicular magnetic anisotropies and low in-plane coercivities. The present study shows that an introduction of epitaxial cap-layer is effective in controlling the c-axis perpendicular to the substrate surface.

29 CFR 1952.10 - Requirements for approval of State posters.

Science.gov (United States)

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Requirements for approval of State posters. 1952.10 Section... and Conditions § 1952.10 Requirements for approval of State posters. (a)(1) In order to inform..., States with approved plans shall develop and require employers to post a State poster meeting the...

Spin structure of exchange biased heterostructures. Fe/MnF{sub 2} and Fe/FeF{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Sahoo, B

2006-12-18

In this work, the {sup 57}Fe probe layer technique is used in order to investigate the depth- and temperature-dependent Fe-layer spin structure of exchange biased Fe/MnF{sub 2} and Fe/FeF{sub 2} (pseudo-twinned) antiferromagnetic (AFM) systems by conversion electron Moessbauer spectroscopy (CEMS) and nuclear resonant scattering (NRS) of synchrotron radiation. Two kinds of samples with a 10 A {sup 57}Fe probe layer directly at or 35 A away from the interface, labeled as interface and center sample, respectively, were studied in this work. The results obtained by CEMS for Fe/MnF{sub 2} suggests that, at 80 K, i.e., above T{sub N}=67 K of MnF{sub 2}, the remanent state Fe-layer spin structure of the two studied samples are slightly different due to their different microstructure. In the temperature range from 300 K to 80 K, the Fe-layer spin structure does not change just by zero-field cooling the sample in remanence. For Fe/FeF{sub 2}, a continuous non-monotonic change of the remanent-state Fe spin structure was observed by cooling from 300 K to 18 K. NRS of synchrotron radiation was used to investigate the temperature- and depth-dependent Fe-layer spin structure during magnetization reversal in pseudo-twinned Fe/MnF{sub 2}. A depthdependent Fe spin structure in an applied magnetic field (applied along the bisector of the twin domains) was observed at 10 K, where the Fe spins closer to the interface are not aligned along the field direction. The depth-dependence disappears at 150 K. (orig.)

Growth and microstructure of iron nitride layers and pore formation in {epsilon}-Fe{sub 3}N

Energy Technology Data Exchange (ETDEWEB)

Middendorf, C.; Mader, W. [Univ. Bonn, Inst. fuer Anorganische Chemie, Bonn (Germany)

2003-03-01

Layers of {epsilon}-Fe{sub 3}N and {gamma}'-Fe{sub 4}N on ferrite were produced by nitriding iron single crystals or rolled sheets of iron in flowing ammonia at 520 C. The nitride layers were characterised using X-ray diffraction, light microscopy as well as scanning and transmission electron microscopy. The compound layer consists of {epsilon}-Fe{sub 3}N at the surface and of {gamma}'-Fe{sub 4}N facing the ferrite. After 4 h of nitriding, pores develop in the near surface region of {epsilon}-Fe{sub 3}N showing more or less open porosity. Growth of the entire compound layer as well as of the massive and the porous {epsilon}-Fe{sub 3}N sublayer is diffusion-controlled and follows a parabolic growth rate. The {gamma}'-Fe{sub 4}N layer is formed as a transition phase within a narrow interval of nitrogen activity, and it shows little growth in thickness. The transformation of {gamma}'-Fe{sub 4}N to {epsilon}-Fe{sub 3}N is topotactic, where the orientation of the closed-packed iron layers of the crystal structures is preserved. Determination of lattice plane spacings was possible by X-ray diffraction, and this was correlated to the nitrogen content of {epsilon}-Fe{sub 3}N. While the porous layer exhibits an enhanced nitrogen content corresponding to the chemical composition Fe{sub 3}N{sub 1.1}, the massive e Fe{sub 3}N layer corresponds to Fe{sub 3}N{sub 1.0}. The pore formation in {epsilon}-Fe{sub 3}N{sub 1.1} is concluded to be the result of excess nitrogen atoms on non-structural sites, which have a high mobility. Therefore, recombination of excess nitrogen to molecular N{sub 2} at lattice defects is preferred in {epsilon}-Fe{sub 3}N with high nitrogen content compared to stoichiometric {epsilon}-Fe{sub 3}N{sub 1.0} with nitrogen on only structural sites. (orig.)

Tunneling observation at very low temperature of impurity bands within the gap of the Kondo superconducting system CuFe/Pb(T(K)>T(c))

International Nuclear Information System (INIS)

Dumoulin, Louis; Le Fur, Daniel

1976-01-01

Very low temperature superconducting tunneling experiments on CuFe(12.10 -6 ) backed by superconducting lead show a band of localized states next to the gap edge. There is no quantitative agreement with the perturbative approach of Mueller-Hartmann Zittartz in this system where the Kondo temperature is larger than the superconductive T(c) [fr

Tris(1,10-phenanthroline-κ2N,N′zinc(II chloride 2-phenyl-4-selenazole-5-carboxylate decahydrate

Directory of Open Access Journals (Sweden)

Jin-Bei Shen

2011-02-01

Full Text Available The asymmetric unit of the title salt, [Zn(C12H8N23](C10H6NO2SeCl·10H2O, contains a [Zn(phen3]2+ cation (phen is 1,10-phenanthroline, uncoordinated chloride and 2-phenyl-4-selenazole-5-carboxylate anions and ten uncoordinated water molecules. The central ZnII ion is six-coordinated by six N atoms from three phen ligands in a distorted octahedral geometry. An extensive O—H...O, O—H...N and O—H...Cl hydrogen-bonding network stabilizes the crystal structure.

Electromagnetic and microwave absorption properties of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19}

Energy Technology Data Exchange (ETDEWEB)

Chen, Jing [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Meng, Pingyuan [Huzhou Innovation Center of Advanced Materials, Shanghai Institute of Ceramics Chinese Academy of Sciences, Huzhou 215100 (China); Wang, Meiling [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Zhou, Guanchen [School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Wang, Xinqing [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China); Xu, Guangliang, E-mail: xuguangliang@swust.edu.cn [School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang 621010 (China)

2016-09-15

To improve the impedance matching and then achieve a better microwave absorption performance in electromagnetic absorber, the Mg{sup 2+} was added to occupy the sites of Co{sup 2+} in hexagonal-type ferrite BaCoTiFe{sub 10}O{sub 19}. BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} were synthesized by a simple sol-gel combustion technique and the phase of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} was confirmed by X-ray diffraction analysis (XRD). The grain size of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} was in the range of 100–400 nm and crystal particles were refined with the augment of doped Mg{sup 2+}. Based on the static magnetic measurement, the coercivity (H{sub c}) increased and the saturation magnetization (M{sub s}) decreased as the x increased. Moreover, it was found that BaMg{sub 0.4}Co{sub 0.6}TiFe{sub 10}O{sub 19} possessed a maximum reflection loss of −33.7 dB with a matching thickness of 2.0 mm measured by the vector net-analyzer in the frequency of 0.5–18 GHz, which also had a bandwidth below −20 dB ranging from 11.5 GHz to 17.2 GHz. Meanwhile, the permeability of the prepared ferrites could be adjusted and a proper match was provided between dielectric and magnetic properties by controlling the doped content of Mg{sup 2+}, which would be significant to the application of BaMg{sub x}Co{sub 1−x}TiFe{sub 10}O{sub 19} in the field of the microwave absorbing materials. - Highlights: • The Mg{sup 2+} ions were first employed to occupy the place of Co{sup 2+} ions in BaCoTiFe{sub 10}O{sub 19}. • The grains were refined as Co substitution by Mg in ferrite. • The peaks of complex permeability shift to high frequency with Mg{sup 2+} substituted. • The coercivity increased and saturation magnetization slightly decreased. • Substitution of Mg{sup 2+} enhanced microwave absorption and broadened bandwidth.

The 10B(n,α)7Li cross section

International Nuclear Information System (INIS)

1997-01-01

The data base relevant to an evaluation of the 10 B(n,α) standard cross sections have been improved through interlaboratory collaboration. Changes in the evaluated 10 B(n,α) cross sections resulted form the measurements made since the ENDF/B-VI evaluation have been estimated. 12 refs, 4 figs

16 CFR 500.10 - Units of fluid measure, how expressed.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Units of fluid measure, how expressed. 500... UNDER SECTION 4 OF THE FAIR PACKAGING AND LABELING ACT § 500.10 Units of fluid measure, how expressed. (a) Use of the terms “net” or “net contents” is optional. (b) Declaration of net quantity of contents...

10 CFR 1017.29 - Civil penalty.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Civil penalty. 1017.29 Section 1017.29 Energy DEPARTMENT... INFORMATION Violations § 1017.29 Civil penalty. Link to an amendment published at 74 FR 66033, Dec. 14, 2009... subject to a civil penalty under this part: (1) 10 CFR Part 1017—Identification and Protection of...

46 CFR 7.120 - Mexican/United States border to Point Fermin, CA.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Mexican/United States border to Point Fermin, CA. 7.120 Section 7.120 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY PROCEDURES APPLICABLE TO THE PUBLIC... from the southerly tower of the Coronado Hotel in approximate position latitude 32°40.8′ N. longitude...

19 CFR 210.10 - Institution of investigation.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 3 2010-04-01 2010-04-01 false Institution of investigation. 210.10 Section 210.10 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Commencement of Preinstitution Proceedings and Investigations...

Development of Fe-B Based Bulk Metallic Glasses: Morphology of Residual Phases in Fe50Ni16Mo6B18Zr10 Glass

Directory of Open Access Journals (Sweden)

Tiburce A. Aboki

2013-04-01

Full Text Available Iron-boron based bulk metallic glasses (BMG development has been initiated using Fe40Ni38Mo4B18 as precursor. Addition of zirconium up to 10 atomic % along with the reduction of Ni proportion improves the glass forming ability (GFA, which is optimum when Ni is suppressed in the alloy. However melting instability occurred during the materials fabrication resulting in the formation of residual crystalline phases closely related to the amorphous phase. Microstructure study shows an evolution from amorphous structure to peculiar acicular structure, particularly for Fe50Ni16Mo6B18Zr10, suggesting the amorphous structure as interconnected atomic sheets like “atomic mille feuilles” whose growth affects the alloys’ GFA.

Ultrasound surface treatment of Kh18N10T steel with different structural state. Ul'trazvukovaya poverkhnostnaya obrabotka stali Kh18N10T s razlichnym strukturnym sostoyaniem

Energy Technology Data Exchange (ETDEWEB)

Aksenov, V K; Danilov, P A; Mats, A V; Netesov, V M; Yaes, A A [AN Ukrainskoj SSR, Kharkov (Ukrainian SSR). Fiziko-Tekhnicheskij Inst.

1989-09-01

Ultrasound surface treatment (USST) is studied for its effect on the structure and mechanical-and-physical properties of Kh18N10T steel with different prehistory. It is shown that surface treatment may both increase and decrease steel microhardness.

78 FR 62305 - Fire Prevention Week, 2013

Science.gov (United States)

2013-10-16

..., by virtue of the authority vested in me by the Constitution and the laws of the United States do..., in accordance with Public Law 107-51, the flag of the United States will be flown at half- staff at.... (Presidential Sig.) [FR Doc. 2013-24498 Filed 10-15-13; 8:45 am] Billing code 3295-F4 ...

Magnetic properties of co-modified Fe,N-TiO2 nanocomposites

Directory of Open Access Journals (Sweden)

Zolnierkiewicz Grzegorz

2015-01-01

Full Text Available Iron and nitrogen co-modified titanium dioxide nanocomposites, nFe,N-TiO2 (where n = 1, 5 and 10 wt% of Fe, were investigated by detailed dc susceptibility and magnetization measurements. Different kinds of magnetic interactions were evidenced depending essentially on iron loading of TiO2. The coexistence of superparamagnetic, paramagnetic and ferromagnetic phases was identified at high temperatures. Strong antiferromagnetic interactions were observed below 50 K, where some part of the nanocomposite entered into a long range antiferromagnetic ordering. Antiferromagnetic interactions were attributed to the magnetic agglomerates of iron-based and trivalent iron ions in FeTiO3 phase,whereas ferromagnetic interactions stemmed from the F-center mediated bound magnetic polarons.

19 CFR 10.3 - Drawback; internal-revenue tax.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Drawback; internal-revenue tax. 10.3 Section 10.3... and Returned § 10.3 Drawback; internal-revenue tax. (a) Except as prescribed in § 10.1(f) or in... tax is imposed on the importation of like articles not previously exported from the United States or...

46 CFR 2.10-130 - Fees for examination of foreign mobile offshore drilling units.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Fees for examination of foreign mobile offshore drilling... drilling units. Each foreign mobile offshore drilling unit must pay: (a) For examination for the issuance... Equipment of Mobile Offshore Drilling Units, a fee of $1,830. (b) For examination for the issuance of a...

Partial breaking of N = 1, D = 10 supersymmetry

International Nuclear Information System (INIS)

Bellucci, S.

1999-01-01

In this paper is described the spontaneous partial breaking of N =1, D =10 supersymmetry to N = (1, 0), d = 6 and its dimensionally-reduced versions in the framework of nonlinear realizations. The basic Goldstone superfield is N = (1, 0), d = 6 hyper multiplet superfield satisfying a nonlinear generalization of the standard hyper multiplet constraint. It is here interpreted the generalized constraint as the manifestly world volume supersymmetric form of equations of motion of the type 1 super 5-brane in D 10. The related issues here addressed are a possible existence of brane extension of off-shell hyper multiplet actions, the possibility to utilize vector N = (1, 0), d =6 supermultiplet as the Goldstone one, and the description of 1/4 breaking of N =1, D = 11 supersymmetry

Design of fuel element for RA10

International Nuclear Information System (INIS)

Estevez, Esteban A.; Markiewicz, Mario; Gerding, Roberto

2012-01-01

The RA-10 reactor is an open pool multipurpose reactor. It is intended for radioisotopes production, fuel irradiation and use of neutron beam experiments. The nominal configuration core consists of 19 fuel elements (FE) and 6 in-core irradiation positions. With regard to the FE, although both conceptual design and manufacturing technology are similar to the already developed and qualified by CNEA (MTR fuel flat plate), the conditions imposed by the new reactor on FE's are more demanding that previous supplies. Here it should be mentioned the magnitude of the hydrodynamic forces acting on the FE caused by coolant flow through the core (upward) and mainly by the high coolant velocity between fuel plates (greater than 5 times than those currently in operation). Moreover, the high power density results in higher heat flux in fuel plates and greater temperature gradient. As a result of these increased demands present during irradiation, and in order to maintain a high level of reliability, it is necessary carry out some modifications in the mechanical design of the FE (with respect to the so-called ECBE design or s tandard ) . Design verification is performed through analytical and code calculations, and hydrodynamic tests on a full-scale prototype. This article describes the design of the FE for RA 10 reactor, with special emphasis on those aspects that represent innovations in the traditional design (ECBE). It also presents the functional requirements, design criteria and design limits established according to the reactor operational states (author)

Structural transition of (InSb)n clusters at n = 6-10

Science.gov (United States)

Lu, Qi Liang; Luo, Qi Quan; Huang, Shou Guo; Li, Yi De

2016-10-01

An optimization strategy combining global semi-empirical quantum mechanical search with all-electron density functional theory was adopted to determine the lowest energy structure of (InSb)n clusters with n = 6-10. A new structural growth pattern of the clusters was observed. The lowest energy structures of (InSb)6 and (InSb)8 were different from that of previously reported results. Competition existed between core-shell and cage-like structures of (InSb)8. The structural transition of (InSb)n clusters occurred at size n = 8-9. For (InSb)9 and (InSb)10 clusters, core-shell structure were more energetically favorable than the cage. The corresponding electronic properties were investigated.

28 CFR 16.10 - Preservation of records.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Preservation of records. 16.10 Section 16.10 Judicial Administration DEPARTMENT OF JUSTICE PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION... title 44 of the United States Code or the National Archives and Records Administration's General Records...

Spacer layer effect and microstructure on multi-layer [NdFeB/Nb]n films

International Nuclear Information System (INIS)

Tsai, J.-L.; Yao, Y.-D.; Chin, T.-S.; Kronmueller, H.

2002-01-01

Spacer layer effect on multi-layer [NdFeB/Nb] n films has been investigated from the variation of magnetic properties and microstructure of the films. From a HRTEM cross-section view observation, the average grain size of [NdFeB/Nb] n multi-layers was controlled by both annealing temperature and thickness of NdFeB layer. Selected area diffraction pattern indicated that the structure of Nb spacer layer was amorphous. The grain size and coercivity of [NdFeB x /Nb] n films change from 50 nm and 16.7 kOe to 167 nm and 9 kOe for films with x=40 nm, n=10 and x=200 nm, n=2, respectively

Evaluación por rendimiento de 12 genotipos promisorios de fríjol voluble (Phaseolus vulgaris L. tipo Bola roja y Reventón para las zonas frías de Colombia

Directory of Open Access Journals (Sweden)

López Jesús Edgardo

2006-12-01

Full Text Available

10.0pt; font-family: ";Cambria";,";serif";; mso-ascii-theme-font: major-latin; mso-fareast-font-family: Baskerville; mso-hansi-theme-font: major-latin; mso-bidi-font-family: Baskerville;">El fríjol común (10.0pt; font-family: ";Cambria";,";serif";; mso-ascii-theme-font: major-latin; mso-fareast-font-family: Baskerville-Italic; mso-hansi-theme-font: major-latin; mso-bidi-font-family: Baskerville-Italic;">Phaseolus vulgaris 10.0pt; font-family: ";Cambria";,";serif";; mso-ascii-theme-font: major-latin; mso-fareast-font-family: Baskerville; mso-hansi-theme-font: major-latin; mso-bidi-font-family: Baskerville;">L. es un alimento básico en la región Andina por ser una fuente rica en proteína y de bajo costo. La investigación para incrementar rendimientos en esta leguminosa es una opción para mejorar la competitividad en el mercado mundial. El objetivo principal de este trabajo fue evaluar por rendimiento los genotipos promisorios de fríjol voluble, tipos Bola roja y Reventón, para las zonas frías de Colombia mediante el análisis de sendero. Se realizó un diseño de bloques completos al azar con tres réplicas para evaluar 10 genotipos promisorios de fríjol voluble. El análisis de sendero para el rendimiento por planta y las correlaciones entre el rendimiento y sus componentes mostraron que el carácter número de vainas por planta es el de mayor importancia sobre la determinación del rendimiento, en comparación con los caracteres peso de 100 semillas y número de semillas por vaina, tanto en los genotipos de fríjol voluble tipo Bola roja como tipo Reventón. 

Measuring Information Security Performance with 10 by 10 Model for Holistic State Evaluation.

Directory of Open Access Journals (Sweden)

Igor Bernik

Full Text Available Organizations should measure their information security performance if they wish to take the right decisions and develop it in line with their security needs. Since the measurement of information security is generally underdeveloped in practice and many organizations find the existing recommendations too complex, the paper presents a solution in the form of a 10 by 10 information security performance measurement model. The model-ISP 10×10M is composed of ten critical success factors, 100 key performance indicators and 6 performance levels. Its content was devised on the basis of findings presented in the current research studies and standards, while its structure results from an empirical research conducted among information security professionals from Slovenia. Results of the study show that a high level of information security performance is mostly dependent on measures aimed at managing information risks, employees and information sources, while formal and environmental factors have a lesser impact. Experts believe that information security should evolve systematically, where it's recommended that beginning steps include technical, logical and physical security controls, while advanced activities should relate predominantly strategic management activities. By applying the proposed model, organizations are able to determine the actual level of information security performance based on the weighted indexing technique. In this manner they identify the measures they ought to develop in order to improve the current situation. The ISP 10×10M is a useful tool for conducting internal system evaluations and decision-making. It may also be applied to a larger sample of organizations in order to determine the general state-of-play for research purposes.

Measuring Information Security Performance with 10 by 10 Model for Holistic State Evaluation.

Science.gov (United States)

Bernik, Igor; Prislan, Kaja

Organizations should measure their information security performance if they wish to take the right decisions and develop it in line with their security needs. Since the measurement of information security is generally underdeveloped in practice and many organizations find the existing recommendations too complex, the paper presents a solution in the form of a 10 by 10 information security performance measurement model. The model-ISP 10×10M is composed of ten critical success factors, 100 key performance indicators and 6 performance levels. Its content was devised on the basis of findings presented in the current research studies and standards, while its structure results from an empirical research conducted among information security professionals from Slovenia. Results of the study show that a high level of information security performance is mostly dependent on measures aimed at managing information risks, employees and information sources, while formal and environmental factors have a lesser impact. Experts believe that information security should evolve systematically, where it's recommended that beginning steps include technical, logical and physical security controls, while advanced activities should relate predominantly strategic management activities. By applying the proposed model, organizations are able to determine the actual level of information security performance based on the weighted indexing technique. In this manner they identify the measures they ought to develop in order to improve the current situation. The ISP 10×10M is a useful tool for conducting internal system evaluations and decision-making. It may also be applied to a larger sample of organizations in order to determine the general state-of-play for research purposes.

19 CFR 10.18 - Valuation of assembled articles.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Valuation of assembled articles. 10.18 Section 10... THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. General Provisions Articles Assembled Abroad with United States Components § 10.18 Valuation of assembled articles. As in the case of...

Dependence Of The Structure And Magnetic Properties Of Cast Plate-Shaped Nd60Fe30Al10 Samples On Their Thickness

Directory of Open Access Journals (Sweden)

Michalski B.

2015-09-01

Full Text Available The hard magnetic Nd-Fe-Al alloys are inferior to Nd-Fe-B magnets as far as the magnetic properties are concerned, but their great advantage is that they need no additional annealing to achieve good magnetic properties. These properties depend on the cooling rate from the melting state, and on the thickness of the sample - the best values are achieved at the quenching rates at which the samples have a thickness of 0.3-2 mm. The present study is concerned with the correlation between the magnetic properties of the plate-shaped Nd60Fe30Al10 samples and their size - thickness. Two casting ways: with the melt stream perpendicular direction and parallel to the surface of the plates were used. The plates were produced by pressure casting and suction casting. The studies have shown that the cooling rates depends on local propagation on liquid metal in the mold resulting in heterogeneity of structure and properties.

Fe-N and (Fe, Ni)-N Fine Powders for Magnetic Recording

International Nuclear Information System (INIS)

Chen Ziyu; Li Fashen

1998-01-01

Combining Moessbauer spectroscopy with magnetic property measurement, we have studied Fe-N and (Fe, Ni)-N powders for magnetic recording. The typical particles of the core (α-Fe)/shell (γ'-Fe 4 N) structure have been successfully prepared. All the products are stabilized in a multi-organic solution. It has been found that the coercivity can be changed from 300 to 800 Oe by adjusting the shape of the particles. The special saturation magnetization of the particles can be adjusted from 120 to 180emu/g and their chemical stability is improved by substituting nickel for iron in γ'-Fe 4 N. Following experiments for corrosion resistance, it is expected that (Fe, Ni)-N and the core/shell particles will be applied as recording media in the near future

Fe-N and (Fe, Ni)-N Fine Powders for Magnetic Recording

Energy Technology Data Exchange (ETDEWEB)

Chen Ziyu; Li Fashen [Lanzhou University, Department of Physics (China)

1998-12-15

Combining Moessbauer spectroscopy with magnetic property measurement, we have studied Fe-N and (Fe, Ni)-N powders for magnetic recording. The typical particles of the core ({alpha}-Fe)/shell ({gamma}'-Fe{sub 4}N) structure have been successfully prepared. All the products are stabilized in a multi-organic solution. It has been found that the coercivity can be changed from 300 to 800 Oe by adjusting the shape of the particles. The special saturation magnetization of the particles can be adjusted from 120 to 180emu/g and their chemical stability is improved by substituting nickel for iron in {gamma}'-Fe{sub 4}N. Following experiments for corrosion resistance, it is expected that (Fe, Ni)-N and the core/shell particles will be applied as recording media in the near future.

10 CFR 35.647 - Additional technical requirements for mobile remote afterloader units.

Science.gov (United States)

2010-01-01

... on the remote afterloader unit, on the control console, and in the facility; (3) Viewing and intercom... 10 Energy 1 2010-01-01 2010-01-01 false Additional technical requirements for mobile remote... MATERIAL Photon Emitting Remote Afterloader Units, Teletherapy Units, and Gamma Stereotactic Radiosurgery...

12 CFR 404.10 - Fee waivers or reductions.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Fee waivers or reductions. 404.10 Section 404.10 Banks and Banking EXPORT-IMPORT BANK OF THE UNITED STATES INFORMATION DISCLOSURE Procedures for Disclosure of Records Under the Freedom of Information Act. § 404.10 Fee waivers or reductions. (a) General...

Quasicrystalline phase formation in the mechanically alloyed Al{sub 70}Cu{sub 20}Fe{sub 10}

Energy Technology Data Exchange (ETDEWEB)

Medeiros, S. N. de, E-mail: snm@dfi.uem.br; Cadore, S.; Pereira, H. A.; Santos, I. A.; Colucci, C. C.; Paesano, A. [Universidade Estadual de Maringa, Departamento de Fisica (Brazil)

2010-01-15

In the present work, the formation of the Al{sub 70}Cu{sub 20}Fe{sub 10} icosahedral phase by mechanical alloying the elemental powders in a high-energy planetary mill was investigated by X-ray diffraction and Moessbauer spectroscopy. It was verified that the sample milled for 80 h produces an icosahedral phase besides Al(Cu, Fe) solid solution ({beta}-phase) and Al{sub 2}Cu intermetallic phase. The Moessbauer spectrum for this sample was fitted with a distribution of quadrupole splitting, a doublet and a sextet, revealing the presence of the icosahedral phase, {beta}-phase and {alpha}-Fe, respectively. This compound is not a good hydrogen storage. The results of the X-ray diffraction and Moessbauer spectroscopy of the sample milled for 40 h and annealed at 623 deg. C for 16 h shows essentially single i-phase and tetragonal Al{sub 7}Cu{sub 2} Fe phase.

Coercivity Recovery Effect of Sm-Fe-Cu-Al Alloy on Sm2Fe17N3 Magnet

Science.gov (United States)

Otogawa, Kohei; Asahi, Toru; Jinno, Miho; Yamaguchi, Wataru; Takagi, Kenta; Kwon, Hansang

2018-03-01

The potential of a Sm-Fe-Cu-Al binder for improvement of the magnetic properties of Sm2Fe17N3 was examined. Transmission electron microscope (TEM) observation of a Sm-Fe-Cu-Al alloy-bonded Sm2Fe17N3 magnet which showed high coercivity revealed that the Sm-Fe-Cu-Al alloy had an effect of removing the surface oxide layer of the Sm2 Fe17N3 grains. However, the Sm-Fe-Cu-Al binder was contaminated by carbon and nitrogen, which originated from the organic solvent used as the milling medium during pulverization. To prevent carbon and nitrogen contamination, the Sm-Fe- Cu-Al alloy was added directly on the surface of the Sm2Fe17N3 grains by sputtering. Comparing the recovered coercivity per unit amount of the added binder the uncontaminated binder-coated sample had a higher coercivity recovery effect than the milled binder-added sample. These results suggested that sufficient addition of the contamination-free Sm-Fe-Cu-Al binder has the possibility to reduce the amount of binder necessary to produce a high coercive Sm2Fe17N3 magnet.

MR cholangiopancreatography. Comparison of images obtained with 1.0 and 1.5 tesla units

International Nuclear Information System (INIS)

Yasui, Masayasu; Ito, Katsuyoshi; Koike, Shinji; Matsunaga, Naofumi

2002-01-01

The purpose of this study was to compare the image quality and visualization obtained in MR cholangiopancreatography (MRCP) using different high-field strength (1.0 vs. 1.5 Tesla) MR units and to assess the effect of field strength on MRCP. This study population included 10 healthy volunteers and 37 patients suspected of having pancreatobiliary diseases. MRCP images were obtained using two MR units with different high-field strengths (1.0 and 1.5 Tesla), with half-Fourier acquisition single-shot turbo spin-echo (HASTE) and rapid acquisition by relaxation enhancement (RARE) sequences. The image quality and visualization of each portion of the pancreatobiliary system were graded and recorded using a four-point scale. Additionally, the signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) were measured. The SNR and CNR in HASTE sequences acquired with the 1.5 Tesla (T) unit were significantly higher than those acquired with the 1.0 T unit (p=0.001). In qualitative analysis, there were no statistically significant differences in image quality or visualization of the ducts in either HASTE or RARE sequences between 1.0 T and 1.5 T. Our study showed that visual image quality provided by MRCP was equivalent at 1.0 and 1.5 T. (author)

Measurement of double differential cross sections of secondary neutrons from 238U, 209Bi, Fe and 9Be around 10 MeV

International Nuclear Information System (INIS)

Qi Bujia; Tang Hongqing; Zhou Zuying

1995-01-01

Double differential cross sections of 238 U, 209 Bi, Fe and 9 Be around 10 MeV are measured at 5 or 6 or 8 angles between 35 degree and 120 degree by means of both normal and abnormal TOF spectrometers using T(d,n) neutron source. The present result of 9 Be is compared with existing experimental data. The data of 238 U and 209 Bi are compared with theoretical calculations. A good agreement is achieved

7 CFR 1212.32 - United States Customs Service.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false United States Customs Service. 1212.32 Section 1212... § 1212.32 United States Customs Service. “United States Customs Service” or “Customs” means the United States Customs and Border Protection, an agency of the Department of Homeland Security. Honey Packers and...

Voltage manipulation of the magnetization reversal in Fe/n-GaAs/piezoelectric heterostructure

International Nuclear Information System (INIS)

Li, Yuanyuan; Luo, Wengang; Zhu, Lijun; Zhao, Jianhua; Wang, Kaiyou

2015-01-01

We carefully investigated the in-plane magnetization reversal and corresponding magnetic domain structures in Fe/n-GaAs/piezoelectric heterostructure using longitudinal magneto-optical Kerr microscopy. The coexistence of the in-plane <100> cubic and [11 ¯ 0] uniaxial magnetic anisotropy was observed in this system at virgin state. The piezo voltages can effectively manipulate the magnetic properties of the Fe/n-GaAs/piezoelectric heterostructure, where the manipulation of two-jump to one-jump magnetization switching during the magnetic reversal was achieved with magnetic field applied in [100] direction. Our findings on manipulation of ferromagnetization in this heterostructure could be important for future metal-semiconductor spintronic applications. The additional uniaxial anisotropy induced by piezo voltages obtained at ±75 V is ±1.4×10 3 J/m 3 . - Highlights: • In this work, we use piezo voltages not only realize the significant change of coercivity but also effectively manipulate the magnetization transition from one step to two steps during magnetic reversal, indicating that the piezo-voltages can be used to effectively control the magnetization reversal. • The additional uniaxial anisotropy induced by piezo voltages at +/−75 V are +/−1.4×10 3 J/m 3 . This work could be very used for future metal-semiconductor spintronic devices

Phase Transformations and Phase Equilibria in the Fe-N System at Temperatures below 573 K

DEFF Research Database (Denmark)

Malinov, S.; Böttger, A.J.; Mittemeijer, E.J.

2001-01-01

The phase transformations of homogeneous Fe-N alloys of nitrogen contents from 10 to 26 at. pct were investigated by means of X-ray diffraction analysis upon aging in the temperature range from 373 to 473 K. It was found that precipitation of alpha double prime-Fe16N2 below 443 K does not only oc...

Effect of Ta buffer and NiFe seed layers on pulsed-DC magnetron sputtered Ir{sub 20}Mn{sub 80}/Co{sub 90}Fe{sub 10} exchange bias

Energy Technology Data Exchange (ETDEWEB)

Oksuezoglu, Ramis Mustafa, E-mail: rmoksuzoglu@anadolu.edu.t [University of Anadolu, Faculty of Engineering and Architecture, Department of Materials Sciences and Engineering, Iki Eyluel Campus, 26555 Eskisehir (Turkey); Yildirim, Mustafa; Cinar, Hakan [University of Anadolu, Faculty of Engineering and Architecture, Department of Materials Sciences and Engineering, Iki Eyluel Campus, 26555 Eskisehir (Turkey); Hildebrandt, Erwin; Alff, Lambert [Department of Materials Sciences, Darmstadt University of Technology, Petersenstrasse 23, D-64287 Darmstadt (Germany)

2011-07-15

A systematic investigation has been done on the correlation between texture, grain size evolution and magnetic properties in Ta/Ni{sub 81}Fe{sub 19}/Ir{sub 20}Mn{sub 80}/Co{sub 90}Fe{sub 10}/Ta exchange bias in dependence of Ta buffer and NiFe seed layer thickness in the range of 2-10 nm, deposited by pulsed DC magnetron sputtering technique. A strong dependence of <1 1 1> texture on the Ta/NiFe thicknesses was found, where the reducing and increasing texture was correlated with exchange bias field and unidirectional anisotropy energy constant at both NiFe/IrMn and IrMn/CoFe interfaces. However, a direct correlation between average grain size in IrMn and H{sub ex} and H{sub c} was not observed. L1{sub 2} phase IrMn{sub 3} could be formed by thickness optimization of Ta/NiFe layers by deposition at room temperature, for which the maximum exchange coupling parameters were achieved. We conclude finally that the coercivity is mainly influenced by texture induced interfacial effects at NiFe/IrMn/CoFe interfaces developing with Ta/NiFe thicknesses. - Research highlights: We discussed the influence of Ta/NiFe thicknesses on structure and grain size in AF layer and texture. A direct correlation between the <1 1 1> texture and exchange coupling was found. A direct relation between average grain size and H{sub ex} and H{sub c} was not observed. L1{sub 2} phase IrMn{sub 3} was formed by deposition at room temperature for Ta (5-6 nm)/NiFe (6-8 nm). We conclude that the coercivity is influenced by order/disorder at NiFe/IrMn/CoFe interfaces.

(SiC/AlN)2 multilayer film as an effective protective coating for sintered NdFeB by magnetron sputtering

Science.gov (United States)

You, Yu; Li, Heqin; Huang, Yiqin; Tang, Qiong; Zhang, Jing; Xu, Jun

2017-08-01

SiC/AlN and (SiC/AlN)2 multilayer films with a well-arranged bilayer structure and a four-layer structure are prepared respectively on NdFeB substrates by a magnetron sputtering method. Crystal phase and microstructures of the SiC/AlN and (SiC/AlN)2 films are investigated using x-ray diffraction (XRD), field-emission scanning electron microscope (FESEM) and atomic force microscope (AFM). It is observed that the surface of the (SiC/AlN)2 four-layer film is much denser and smoother than that of the SiC/AlN bilayer film. Corrosion behaviors of the NdFeB substrates coated with SiC/AlN and (SiC/AlN)2 films as well as the bare NdFeB substrate are evaluated by potentiodynamic polarization curve tests. It is revealed that the lateral growth structures developed in interfaces are favorable for an enhanced corrosion resistance. Corrosion current densities of the (SiC/AlN)2 coated NdFeB measured in acid, alkali and salt solutions are 2.796  ×  10-9, 3.65  ×  10-6, and 2.912  ×  10-6 A cm-2, respectively, which are much lower than those of the bare NdFeB and the SiC/AlN coated NdFeB.

8 CFR 287.10 - Expedited internal review process.

Science.gov (United States)

2010-01-01

... jurisdiction regarding criminal violations of law. [68 FR 35281, June 13, 2003] ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Expedited internal review process. 287.10... OFFICERS; POWERS AND DUTIES § 287.10 Expedited internal review process. (a) Violations of standards for...

Precise measurement of the neutron capture reaction 54Fe(n,γ)55Fe via AMS

International Nuclear Information System (INIS)

Wallner, A; Buczak, K; Forstner, O; Golser, R; Kutschera, W; Lederer, C; Priller, A; Steier, P; Belgya, T; Szentmiklosi, L; Bichler, M; Coquard, L; Dillmann, I; Kaeppeler, F; Mengoni, A; Reifarth, R

2010-01-01

The measurement of cross sections relevant to nuclear astrophysics has become one main research topic at the VERA (Vienna Environmental Research Accelerator) facility. The technique applied, accelerator mass spectrometry (AMS), offers excellent sensitivity for the detection of long-lived radionuclides through ultra-low isotope ratio measurements. We discuss the potential and preliminary results of ongoing precision measurements of neutron-capture cross sections of 54 Fe. Such measurements might help to clarify the recently found discrepancy of s-process nucleosynthesis at lower-mass nuclei (A 55 Fe (t 1/2 = 2.72 yr) was analyzed using AMS. At VERA, detection of 55 Fe was developed with a reproducibility of about 1%, which makes the 54 Fe(n,γ) 55 Fe reaction a precise and unique laboratory measurement, which can serve as a reference to complementary techniques. In this regard a new 55 Fe standard for AMS measurements was produced. The final cross-section data are expected to be accurate to better than 3%. We report a preliminary, however, already significantly improved thermal neutron cross section value of (2.32 ± 0.10) barn, and a value of (6.3 ± 0.6) mbarn for E n = (520 ± 50) keV.

78 FR 53247 - Approval and Promulgation of Implementation Plans; State of Missouri; St. Louis Area...

Science.gov (United States)

2013-08-29

... include amendments to sections (1) through (4) of rule 10 CSR 10-5.480 St. Louis Area Transportation... approving the State's request to amend 10 CSR 10-5.480 St. Louis Area Transportation Conformity Requirements... action'' subject to review by the Office of Management and Budget under Executive Order 12866 (58 FR...

75 FR 61760 - Depository Library Council to the Public Printer; Meeting

Science.gov (United States)

2010-10-06

... GOVERNMENT PRINTING OFFICE Depository Library Council to the Public Printer; Meeting The Depository Library Council to the Public Printer (DLC) will meet on Monday, October 18, 2010, through... regulations. Robert C. Tapella, Public Printer of the United States. [FR Doc. 2010-25047 Filed 10-5-10; 8:45...

37 CFR 1.10 - Filing of correspondence by “Express Mail.”

Science.gov (United States)

2010-07-01

... Office to Addressee” service of the United States Postal Service (USPS) will be considered filed with the...Express Mail.â 1.10 Section 1.10 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES General Provisions General...

42 CFR 455.21 - Cooperation with State Medicaid fraud control units.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Cooperation with State Medicaid fraud control units... Detection and Investigation Program § 455.21 Cooperation with State Medicaid fraud control units. In a State with a Medicaid fraud control unit established and certified under subpart C of this part, (a) The...

SVIP-N 1.0: An integrated visualization platform for neutronics analysis

International Nuclear Information System (INIS)

Luo Yuetong; Long Pengcheng; Wu Guoyong; Zeng Qin; Hu Liqin; Zou Jun

2010-01-01

Post-processing is an important part of neutronics analysis, and SVIP-N 1.0 (scientific visualization integrated platform for neutronics analysis) is designed to ease post-processing of neutronics analysis through visualization technologies. Main capabilities of SVIP-N 1.0 include: (1) ability of manage neutronics analysis result; (2) ability to preprocess neutronics analysis result; (3) ability to visualization neutronics analysis result data in different way. The paper describes the system architecture and main features of SVIP-N, some advanced visualization used in SVIP-N 1.0 and some preliminary applications, such as ITER.

78 FR 62313 - General Pulaski Memorial Day, 2013

Science.gov (United States)

2013-10-16

... the laws of the United States, do hereby proclaim October 11, 2013, as General Pulaski Memorial Day. I...- eighth. (Presidential Sig.) [FR Doc. 2013-24502 Filed 10-15-13; 8:45 am] Billing code 3295-F4 ...

Anomaly of strings of 6d N =(1,0) theories

International Nuclear Information System (INIS)

Shimizu, Hiroyuki; Tachikawa, Yuji

2016-01-01

We obtain the anomaly polynomial of strings of general 6d N =(1,0) theories in terms of anomaly inflow. Our computation sheds some light on the reason why the simplest 6d N =(1,0) theory has E_8 flavor symmetry, and also partially explains a curious numerology in F-theory.

Anomaly of strings of 6d {N}=(1,0) theories

Science.gov (United States)

Shimizu, Hiroyuki; Tachikawa, Yuji

2016-11-01

We obtain the anomaly polynomial of strings of general 6d {N}=(1,0) theories in terms of anomaly inflow. Our computation sheds some light on the reason why the simplest 6d {N}=(1,0) theory has E 8 flavor symmetry, and also partially explains a curious numerology in F-theory.

75 FR 33320 - Notice of Issuance of Final Determination Concerning a Lift Unit for an Overhead Patient Lift...

Science.gov (United States)

2010-06-11

... country of origin of the lift unit which may be offered to the U.S. Government under an undesignated government procurement package.'' Dated: June 7, 2010. Harold M. Singer, Director, Regulations and Disclosure Law Division, Office of International Trade. [FR Doc. 2010-14019 Filed 6-10-10; 8:45 am] BILLING CODE...

37 CFR 10.67 - Settling similar claims of clients.

Science.gov (United States)

2010-07-01

... clients. 10.67 Section 10.67 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE... Office Code of Professional Responsibility § 10.67 Settling similar claims of clients. A practitioner who represents two or more clients shall not make or participate in the making of an aggregate settlement of the...

Dopant spin states and magnetism of Sn{sub 1−x}Fe{sub x}O{sub 2} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Punnoose, A., E-mail: apunnoos@boisestate.edu; Dodge, Kelsey; Reddy, K. M.; Franco, Nevil; Chess, Jordan; Eixenberger, Josh [Department of Physics, Boise State University, Boise, Idaho 83725-1570 (United States); Beltrán, J. J. [Department of Physics, Boise State University, Boise, Idaho 83725-1570 (United States); Grupo de Estado Sólido, Facultad de Ciencias Exactas y Naturales, Universidad de Antioquia UdeA, Calle 70 No 52-21, Medellín (Colombia); Barrero, C. A. [Grupo de Estado Sólido, Facultad de Ciencias Exactas y Naturales, Universidad de Antioquia UdeA, Calle 70 No 52-21, Medellín (Colombia)

2014-05-07

This work reports detailed investigations of a series of ∼2.6 nm sized, Sn{sub 1−x}Fe{sub x}O{sub 2} crystallites with x = 0–0.10 using Mossbauer spectroscopy, x-ray photoelectron spectroscopy (XPS), electron paramagnetic resonance spectroscopy (EPR), and magnetometry to determine the oxidation state of Fe dopants and their role in the observed magnetic properties. The magnetic moment per Fe ion μ was the largest ∼6.48 × 10{sup −3} μ{sub B} for the sample with the lowest (0.001%) Fe doping, and it showed a rapid downward trend with increasing Fe doping. Majority of the Fe ions are in 3+ oxidation state occupying octahedral sites. Another significant fraction of Fe dopant ions is in 4+ oxidation state and a still smaller fraction might be existing as Fe{sup 2+} ions, both occupying distorted sites, presumably in the surface regions of the nanocrystals, near oxygen vacancies. These studies also suggest that the observed magnetism is not due to exchange coupling between Fe{sup 3+} spins. A more probable role for the multi-valent Fe ions may be to act as charge reservoirs, leading to charge transfer ferromagnetism.

Measurement of N and C diffusion in Sm{sub 2}Fe{sub 17} by magnetic relaxation

Energy Technology Data Exchange (ETDEWEB)

Mommer, N.; Hirscher, M.; Gerlach, M.; Van Lier, J.; Kronmueller, H. [Max-Planck-Institut fuer Metallforschung, Stuttgart (Germany); Kubis, M.; Mueller, K.-H. [Institut fuer Festkoerper und Werkstofforschung, Institut fuer Metallische Werkstoffe, D-01171 Dresden (Germany)

1998-10-02

Magnetic after-effect (MAE) measurements of nitrided and carburized Sm{sub 2}Fe{sub 17} compounds were performed in the temperature range of 140 K to 480 K. Both nitrided and carburized compounds show relaxation maxima at 285 and 300 K, respectively, which are absent in pure Sm{sub 2}Fe{sub 17} compounds. Therefore, these relaxation maxima are attributed to jumps of interstitially dissolved nitrogen or carbon atoms. Numerical evaluation yielded an activation enthalpy Q{sup N} (0.84{+-}0.05) eV and a pre-exponential factor {tau}{sub 0}{sup N}=3.10{sup -15{+-}1} s for the short-range diffusion of N atoms. The corresponding values for the carbon diffusion are Q{sup C}=(0.91{+-}0.05) eV and {tau}{sub 0}{sup C}=1.10{sup -15{+-}1} s. The carbon and nitrogen content of the samples was determined from the increase in mass during nitrogenation or carburization to Sm{sub 2}Fe{sub 17}N{sub 1.2} and Sm{sub 2}Fe{sub 17}C{sub 2.6}. (orig.) 18 refs.

Origin of open recoil curves in L1_0-A1 FePt exchange coupled nanocomposite thin film

International Nuclear Information System (INIS)

Goyal, Rajan; Kapoor, Akanksha; Lamba, S.; Annapoorni, S.

2016-01-01

Mixed phase FePt systems with intergranular coupling may be looked upon as natural exchange spring systems. The coupling strength between the soft and hard phase in these systems can be analyzed using recoil curves. However, the origin of open recoil curves depicting the breakdown of exchange coupling or anisotropy variation in hard phase is still an ambiguity and requires an in-depth analysis. In order to investigate this, an analysis of the recoil curves for L1_0–A1 FePt nanocomposite thin films of varying thickness have been performed. The switching field distribution reveals that the maximum of openness of recoil curve is directly proportional to the amount of uncoupled soft phase present in the system. The coupling between the hard and soft phase is also found to increase with the thickness of the film. Monte Carlo simulations on a model three dimensional array of interacting nanomagnetic grains provide further insight into the effect of inter granular exchange interactions between the soft and hard phases. - Highlights: • L1_0-A1 FePt nanocomposites thin films of different thickness have been fabricated by DC sputtering. • Hysteresis curve measurements exhibit perfect single phase (L1_0) like behavior for thicker films. • SFD reveals that the openness of recoil curves is directly linked with the amount of uncoupled soft (A1) phase. • Monte Carlo simulation predicts that the extent of exchange interaction increases with thickness of the film.

Zn-10.2% Fe coating over carbon steel atmospheric corrosion resistance. Comparison with zinc coating

International Nuclear Information System (INIS)

Arnau, G.; Gimenez, E.; Rubio, M.V.; Saura, J.J.; Suay, J.J.

1998-01-01

Zn-10.2% Fe galvanized coating versus hot galvanized coating over carbon steel corrosion performance has been studied. Different periods of atmospheric exposures in various Valencia Community sites, and salt spray accelerated test have been done. Carbon steel test samples have been used simultaneously in order to classify exposure atmosphere corrosivity, and environmental exposure atmosphere characteristics have been analyzed. Corrosion Velocity versus environmental parameters has been obtained. (Author) 17 refs

10 CFR 420.13 - Annual State applications and amendments to State plans.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Annual State applications and amendments to State plans. 420.13 Section 420.13 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION STATE ENERGY PROGRAM Formula..., renewable energy, and alternative transportation fuel goals to be achieved, including wherever practicable...

Surfactant assisted synthesis of aluminum doped SrFe{sub 10}Al{sub 2}O{sub 19} hexagonal ferrite

Energy Technology Data Exchange (ETDEWEB)

Neupane, D., E-mail: dneupane@memphis.edu; Wang, L.; Mishra, S. R. [Department of Physics, The University of Memphis, Memphis, Tennessee 38152 (United States); Poudyal, N.; Liu, J. P. [Department of Physics, The University of Texas, Arlington, Texas 76019 (United States)

2015-05-07

M-type aluminum doped SrFe{sub 10}Al{sub 2}O{sub 19} were synthesized via co-precipitation method using cetyltrimethyl ammonium bromide (CTAB) as a surfactant. The effects of CTAB content (x = 0, 1, 3, and 9 wt. %) on the formation, structure, morphology, magnetic, and dielectric properties of the SrFe{sub 10}Al{sub 2}O{sub 19} nanoparticles were investigated. X-ray diffraction results show elimination of α-Fe{sub 2}O{sub 3} phase from samples prepared using CTAB. Morphological changes including grain and crystallite size was noticed with the increase in the CTAB content. With the increase in CTAB, powder particles grew in hexagonal plates. A linear increase in saturation magnetization, Ms, with CTAB content was observed from 56.5 emu/g at 0% CTAB to 66.4 emu/g at 9% CTAB. This is a net increase of 17.5% in Ms. The coercivity (Hc ∼ 5700 Oe) of sample reached maximum at 1% CTAB and reduced with further CTAB content reaching to a minimum value of 4488 Oe at 9% CTAB. A slight increase in Curie temperature (735 K) was also observed for samples synthesized using CTAB as compared to that of sample prepared in the absence of CTAB (729 K). Samples synthesized with CTAB show higher dielectric constants as compared to samples prepared without CTAB, while dielectric constant for all samples show decrease in value with the increase in frequency. These results imply that CTAB may act as a crystallization master, controlling the nucleation and growth of SrFe{sub 10}Al{sub 2}O{sub 19} crystal. The study delineates the scope of improving magnetic properties of ferrites without substitution of metal ions.

Room-temperature multiferroic and magnetocapacitance effects in M-type hexaferrite BaFe{sub 10.2}Sc{sub 1.8}O{sub 19}

Energy Technology Data Exchange (ETDEWEB)

Tang, Rujun, E-mail: tangrj@suda.edu.cn, E-mail: yanghao@nuaa.edu.cn; Zhou, Hao; You, Wenlong [Jiangsu Key Laboratory of Thin Films, College of Physics, Optoelectronics and Energy, Soochow University, Suzhou 215006 (China); Yang, Hao, E-mail: tangrj@suda.edu.cn, E-mail: yanghao@nuaa.edu.cn [College of Science, Nanjing University of Aeronautics and Astronautics, Nanjing 211106 (China)

2016-08-22

The room-temperature multiferroic and magnetocapacitance (MC) effects of polycrystalline M-type hexaferrite BaFe{sub 10.2}Sc{sub 1.8}O{sub 19} have been investigated. The results show that the magnetic moments of insulating BaFe{sub 10.2}Sc{sub 1.8}O{sub 19} can be manipulated by the electric field at room temperature, indicating the existence of magnetoelectric coupling. Moreover, large MC effects are also observed around the room temperature. A frequency dependence analysis shows that the Maxwell-Wagner type magnetoresistance effect is the dominant mechanism for MC effects at low frequencies. Both the magnetoelectric-type and non-magnetoelectric-type spin-phonon couplings contribute to the MC effects at high frequencies with the former being the dominant mechanism. The above results show that the hexaferrite BaFe{sub 10.2}Sc{sub 1.8}O{sub 19} is a room-temperature multiferroic material that can be potentially used in magnetoelectric devices.

Revisit the landscape of protonated water clusters H+(H2O)n with n = 10-17: An ab initio global search

Science.gov (United States)

Shi, Ruili; Li, Keyao; Su, Yan; Tang, Lingli; Huang, Xiaoming; Sai, Linwei; Zhao, Jijun

2018-05-01

Using a genetic algorithm incorporated with density functional theory, we explore the ground state structures of protonated water clusters H+(H2O)n with n = 10-17. Then we re-optimize the isomers at B97-D/aug-cc-pVDZ level of theory. The extra proton connects with a H2O molecule to form a H3O+ ion in all H+(H2O)10-17 clusters. The lowest-energy structures adopt a monocage form at n = 10-16 and core-shell structure at n = 17 based on the MP2/aug-cc-pVTZ//B97-D/aug-cc-pVDZ+ZPE single-point-energy calculation. Using second-order vibrational perturbation theory, we further calculate the infrared spectra with anharmonic correction for the ground state structures of H+(H2O)10-17 clusters at the PBE0/aug-cc-pVDZ level. The anharmonic correction to the spectra is crucial since it reproduces the experimental results quite well. The extra proton weakens the O-H bond strength in the H3O+ ion since the Wiberg bond order of the O-H bond in the H3O+ ion is smaller than that in H2O molecules, which causes a red shift of the O-H stretching mode in the H3O+ ion.

Multiple anion...π interactions in tris(1,10-phenanthroline-κ(2)N,N')iron(II) bis[1,1,3,3-tetracyano-2-(2-hydroxyethyl)propenide] monohydrate.

Science.gov (United States)

Setifi, Zouaoui; Domasevitch, Konstantin V; Setifi, Fatima; Mach, Pavel; Ng, Seik Weng; Petříček, Vaclav; Dušek, Michal

2013-11-01

In the ionic structure of the title compound, [Fe(C12H8N2)3](C9H5N4O2)2·H2O, the octahedral tris-chelate [Fe(phen)3](2+) dications [Fe-N = 1.9647 (14)-1.9769 (14) Å; phen is 1,10-phenathroline] afford one-dimensional chains by a series of slipped π-π stacking interactions [centroid-to-centroid distances = 3.792 (3) and 3.939 (3) Å]. The 1,1,3,3-tetracyano-2-(2-hydroxyethyl)propenide anions, denoted tcnoetOH(-), reveal an appreciable delocalization of π-electron density, involving the central propenide [C-C = 1.383 (3)-1.401 (2) Å] fragment and four nitrile groups, and this is also supported by density functional theory (DFT) calculations at the B97D/6-311+G(2d,2p) level. Primary noncovalent inter-moiety interactions comprise conventional O-H...O(N) and weak C-H...O(N) hydrogen bonding [O...O(N) = 2.833 (2)-3.289 (5) Å and C...O(N) = 3.132 (2)-3.439 (2) Å]. The double anion...π interaction involving a nitrile group of tcnoetOH(-) and two cis-positioned pyridine rings (`π-pocket') of [Fe(phen)3](2+) [N...centroid = 3.212 (2) and 3.418 (2) Å] suggest the relevance of anion...π stackings for charge-diffuse polycyanoanions and common M-chelate species.

Cupriphication of gold to sensitize d10–d10 metal–metal bonds and near-unity phosphorescence quantum yields

Science.gov (United States)

Galassi, Rossana; Ghimire, Mukunda M.; Otten, Brooke M.; Ricci, Simone; McDougald, Roy N.; Almotawa, Ruaa M.; Alhmoud, Dieaa; Ivy, Joshua F.; Rawashdeh, Abdel-Monem M.; Nesterov, Vladimir N.; Reinheimer, Eric W.; Daniels, Lee M.; Burini, Alfredo; Omary, Mohammad A.

2017-01-01

Outer-shell s0/p0 orbital mixing with d10 orbitals and symmetry reduction upon cupriphication of cyclic trinuclear trigonal-planar gold(I) complexes are found to sensitize ground-state Cu(I)–Au(I) covalent bonds and near-unity phosphorescence quantum yields. Heterobimetallic Au4Cu2 {[Au4(μ-C2,N3-EtIm)4Cu2(µ-3,5-(CF3)2Pz)2], (4a)}, Au2Cu {[Au2(μ-C2,N3-BzIm)2Cu(µ-3,5-(CF3)2Pz)], (1) and [Au2(μ-C2,N3-MeIm)2Cu(µ-3,5-(CF3)2Pz)], (3a)}, AuCu2 {[Au(μ-C2,N3-MeIm)Cu2(µ-3,5-(CF3)2Pz)2], (3b) and [Au(μ-C2,N3-EtIm)Cu2(µ-3,5-(CF3)2Pz)2], (4b)} and stacked Au3/Cu3 {[Au(μ-C2,N3-BzIm)]3[Cu(µ-3,5-(CF3)2Pz)]3, (2)} form upon reacting Au3 {[Au(μ-C2,N3-(N-R)Im)]3 ((N-R)Im = imidazolate; R = benzyl/methyl/ethyl = BzIm/MeIm/EtIm)} with Cu3 {[Cu(μ-3,5-(CF3)2Pz)]3 (3,5-(CF3)2Pz = 3,5-bis(trifluoromethyl)pyrazolate)}. The crystal structures of 1 and 3a reveal stair-step infinite chains whereby adjacent dimer-of-trimer units are noncovalently packed via two Au(I)⋯Cu(I) metallophilic interactions, whereas 4a exhibits a hexanuclear cluster structure wherein two monomer-of-trimer units are linked by a genuine d10–d10 polar-covalent bond with ligand-unassisted Cu(I)–Au(I) distances of 2.8750(8) Å each—the shortest such an intermolecular distance ever reported between any two d10 centers so as to deem it a “metal–metal bond” vis-à-vis “metallophilic interaction.” Density-functional calculations estimate 35–43 kcal/mol binding energy, akin to typical M–M single-bond energies. Congruently, FTIR spectra of 4a show multiple far-IR bands within 65–200 cm−1, assignable to vCu-Au as validated by both the Harvey–Gray method of crystallographic-distance-to-force-constant correlation and dispersive density functional theory computations. Notably, the heterobimetallic complexes herein exhibit photophysical properties that are favorable to those for their homometallic congeners, due to threefold-to-twofold symmetry reduction, resulting in cuprophilic

44 CFR 351.26 - The United States Department of Agriculture.

Science.gov (United States)

2010-10-01

... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false The United States Department of Agriculture. 351.26 Section 351.26 Emergency Management and Assistance FEDERAL EMERGENCY... PREPAREDNESS Interagency Assignments § 351.26 The United States Department of Agriculture. (a) Assist FEMA in...

Quantum-well states and induced magnetism in Fe/CuN/Fe bcc (001) trilayers

DEFF Research Database (Denmark)

Niklasson, A.M.N.; Mirbt, S.; Skriver, Hans Lomholt

1996-01-01

profiles of two single Fe/Cu interfaces. The small deviations from this simple superposition are shown to be a consequence of quantum-well states confined within the paramagnetic spacer. This connection is confirmed by direct calculation of the state density. The results are of conceptual interest...

Airworthiness Certification of Fe-Si3N4-graphite Brake Composites for Military Aircraft

Directory of Open Access Journals (Sweden)

T.R. Prabhu

2015-12-01

Full Text Available Metal matrix hybrid composites are usually preferred for high energy aircraft (1-10 MJ brake pads (HEABP applications. The report focuses mainly on the evaluation of the wear and braking performance of the composite for the military aircraft applications. In this paper, the design and processing of a typical HEABP composite have been discussed in detail. The airworthiness qualification tests for the HEABP and the brake units are outlined with details. Also, brake testing parameters calculations derived from the typical aircraft data are presented for both the laboratory and full scale dynamometer tests. A case study of Fe-Si3N4- graphite composite pads is presented to exemplify the steps involved in the design, development, and airworthiness certification of HEABPs for the 8 MJ energy military aircraft. From the microstructure and wear surface morphology analysis and the results of brake performance parameters, functional tests and aircraft trials, it is concluded that the Fe-Si3N4- graphite composite has a minimum life of 200 normal energy landings with excellent braking performances.

19 CFR 10.431 - Failure to comply with requirements.

Science.gov (United States)

2010-04-01

... United States fails to comply with any requirement of this part. Such measures may include the imposition... Section 10.431 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. United States-Chile...

Determination of the 54Fe(n, 2n)53gFe and 54Fe(n, 2n)53mFe cross sections averaged over a 235U fission neutron spectrum

International Nuclear Information System (INIS)

Ribeiro Guevara, S.; Arribere, M.; Kestelman, A.J.

2002-01-01

The reaction cross sections averaged over a 235 U fission neutron spectrum have been measured for the 54 Fe(n, 2n) 53g Fe and 54 Fe(n, 2n) 53m Fe threshold reactions. The values found are, respectively: (1.14 ± 0.13) μb, and (0.52 ± 0.16) μb. The measured cross sections are referred to the (111± 3) mb standard cross section of the 58 Ni(n, p) 58m+g Co reaction. The (81.7 ± 2.2) mb standard cross section value for the 54 Fe(n, p) 54 Mn reaction, was also used as a monitor to check the results obtained with the Ni standard, leading to an excellent agreement. (author)

Performance of n-in-p pixel detectors irradiated at fluences up to $5x10^{15} n_{eq}/cm^{2}$ for the future ATLAS upgrades

CERN Document Server

INSPIRE-00219560; La Rosa, A.; Nisius, R.; Pernegger, H.; Richter, R.H.; Weigell, P.

We present the results of the characterization of novel n-in-p planar pixel detectors, designed for the future upgrades of the ATLAS pixel system. N-in-p silicon devices are a promising candidate to replace the n-in-n sensors thanks to their radiation hardness and cost effectiveness, that allow for enlarging the area instrumented with pixel detectors. The n-in-p modules presented here are composed of pixel sensors produced by CiS connected by bump-bonding to the ATLAS readout chip FE-I3. The characterization of these devices has been performed with the ATLAS pixel read-out systems, TurboDAQ and USBPIX, before and after irradiation with 25 MeV protons and neutrons up to a fluence of 5x10**15 neq /cm2. The charge collection measurements carried out with radioactive sources have proven the feasibility of employing this kind of detectors up to these particle fluences. The collected charge has been measured to be for any fluence in excess of twice the value of the FE-I3 threshold, tuned to 3200 e. The first result...

CompTIA network+ study guide exam N10-006

CERN Document Server

Lammle, Todd

2015-01-01

All-star N10-006 prep, fully updated for the new exam The CompTIA Network+ Study Guide is your one-stop comprehensive resource in preparing for exam N10-006 Bestselling author and networking Guru Todd Lammle guides you through 100% of all exam objectives detailing the fundamental concepts you will need to know to prepare for the exam. Coverage includes network technologies, installation and configuration, media and topologies, security, and much more, plus practical examples drawn from real-world situations. You also gain access to practice exams and electronic flashcards that facilitate info

75 FR 54690 - 60-Day Notice of Proposed Information Collection: DS-7656; Affidavit of Relationship (AOR); OMB...

Science.gov (United States)

2010-09-08

... Admissions, Bureau of Population, Refugees and Migration (PRM/A) Form Number: DS-7656. Respondents: Persons admitted to the United States as refugees or granted asylum in the United States who are claiming a..., Refugees and Migration, Department of State. [FR Doc. 2010-22354 Filed 9-7-10; 8:45 am] BILLING CODE 4710...

Experimental and theoretical investigation of Fe-catalysis phenomenon in hydrogen thermal desorption form hydrocarbon plasma-discharge films from T-10 tokamak

International Nuclear Information System (INIS)

Stankevich, V.G.; Svechnikov, N.Y.; Lebedev, A.M.; Menshikov, K.A.; Kolbasov, B.N.; Sukhanov, L.P.

2017-01-01

A comprehensive study of hydrocarbon films obtained in the plasma discharge of large fusion facilities will allow the minimization of parasitic capture. The investigation of the effect of Fe impurities on D 2 thermal desorption (TD) from homogeneous CD x films (x ∼ 0.5) formed in the D-plasma discharge of the T-10 tokamak were carried out. The experimental TD spectra of the films showed 2 groups of peaks at 650-850 K and 900-1000 K for 2 adsorption states. The main result of the iron catalysis effect consists in the shift of the high-temperature peak by -24 K and in the increase in the fraction of the weakly bonded adsorption states. To describe the effect of iron impurities on TD of hydrogen isotopes, a structural cluster model based on the interaction of the Fe + ion with the 1,3-C 6 H 8 molecule was proposed. The potential energy surfaces of chemical reactions with the H 2 elimination were calculated using ab initio methods of quantum chemistry. It was established that the activation barrier of hydrogen TD is reduced by about 1 eV due to the interaction of the Fe + ion with the π-subsystem of the 1,3-C 6 H 8 molecule leading to a redistribution of the double bonds along the carbon system

Experimental and theoretical investigation of Fe-catalysis phenomenon in hydrogen thermal desorption from hydrocarbon plasma-discharge films from T-10 tokama

Science.gov (United States)

Stankevich, Vladimir G.; Sukhanov, Leonid P.; Svechnikov, Nicolay Yu.; Lebedev, Alexey M.; Menshikov, Kostantin A.; Kolbasov, Boris N.

2017-10-01

Investigations of the effect of Fe impurities on D2 thermal desorption (TD) from homogeneous CDx films (x ˜ 0.5) formed in the D-plasma discharge of the T-10 tokamak were carried out. The experimental TD spectra of the films showed two groups of peaks at 650-850 K and 900-1000 K for two adsorption states. The main result of the iron catalysis effect consists in the shift of the high-temperature peak by -24 K and in the increase in the fraction of the weakly bonded adsorption states. To describe the effect of iron impurities on TD of hydrogen isotopes, a structural cluster model based on the interaction of the Fe+ ion with the 1,3-C6H8 molecule was proposed. The potential energy surfaces of chemical reactions with the H2 elimination were calculated using ab initio methods of quantum chemistry. It was established that the activation barrier of hydrogen TD is reduced by about 1 eV due to the interaction of the Fe+ ion with the π-subsystem of the 1,3-C6H8 molecule leading to a redistribution of the double bonds along the carbon system. Contribution to the topical issue "Plasma Sources and Plasma Processes (PSPP)"", edited by Luis Lemos Alves, Thierry Belmonte and Tiberiu Minea

The State Geologic Map Compilation (SGMC) geodatabase of the conterminous United States

Science.gov (United States)

Horton, John D.; San Juan, Carma A.; Stoeser, Douglas B.

2017-06-30

The State Geologic Map Compilation (SGMC) geodatabase of the conterminous United States (https://doi. org/10.5066/F7WH2N65) represents a seamless, spatial database of 48 State geologic maps that range from 1:50,000 to 1:1,000,000 scale. A national digital geologic map database is essential in interpreting other datasets that support numerous types of national-scale studies and assessments, such as those that provide geochemistry, remote sensing, or geophysical data. The SGMC is a compilation of the individual U.S. Geological Survey releases of the Preliminary Integrated Geologic Map Databases for the United States. The SGMC geodatabase also contains updated data for seven States and seven entirely new State geologic maps that have been added since the preliminary databases were published. Numerous errors have been corrected and enhancements added to the preliminary datasets using thorough quality assurance/quality control procedures. The SGMC is not a truly integrated geologic map database because geologic units have not been reconciled across State boundaries. However, the geologic data contained in each State geologic map have been standardized to allow spatial analyses of lithology, age, and stratigraphy at a national scale.

33 CFR 17.01-10 - Authority to receive gifts.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Authority to receive gifts. 17.01... GENERAL UNITED STATES COAST GUARD GENERAL GIFT FUND General Provisions § 17.01-10 Authority to receive gifts. (a) The Commandant, United States Coast Guard, may accept, receive, hold, or administer gifts...

78 FR 5303 - Approval and Promulgation of Implementation Plans; State of Missouri; Control of Sulfur Emissions...

Science.gov (United States)

2013-01-25

... stringency of the SIP. Missouri's revision adds 10 CSR 10- 5.570 Control of Sulfur Emissions from Stationary... approving the State's request to add 10 CSR 10-5.570 Control of Sulfur Emissions from Stationary Boilers to... Management and Budget under Executive Order 12866 (58 FR 51735, October 4, 1993); Does not impose an...

Dynamic properties of Ca{sub 10}(Pt{sub 3}As{sub 8})(Fe{sub 1-x}Pt{sub x}As){sub 10} in the superconducting state explored by NMR in high fields

Energy Technology Data Exchange (ETDEWEB)

Brueckner, Felix; Sarkar, Rajib; Surmach, Maksym; Inosov, Dmytro; Klauss, Hans-Henning [Institut fuer Festkoerperphysik, TU Dresden (Germany); Reyes, Arneil P.; Kuhns, Philip L. [National High Magnetic Field Laboratory, Tallahassee, FL (United States)

2016-07-01

The triclinic iron-based superconductor Ca{sub 10}(Pt{sub 3}As{sub 8})(Fe{sub 1-x}Pt{sub x}As){sub 10} with a T{sub c} of 13 K exhibits a unique pseudogap phase below T* = 45 K, recently probed with inelastic neutron scattering. This phase has been attributed to a possible preformation of Cooper pairs. We present detailed NMR results, including {sup 75}As and {sup 195}Pt spectra as well as T{sub 1} measurements. These experiments reveal a drop of spin fluctuations just below T* with a hysteresis in temperature, associated with the emergence of the pseudogap phase. Interestingly, no anomaly at T{sub c} is found. At 3 K, a peak in the T{sub 1} relaxation rate appears, until 1/T{sub 1} eventually vanishes at lower temperatures. This behavior is persistent in large magnetic fields up to 17 T. To interpret these results, scenarios including magnetic order below T* are quite unprobable, since Korringa law is well complied at higher temperatures and no magnetic order is found in μSR. However, the origin of the unique behavior remains unclear for now.

618-10 Burial Ground Trench Remediation and 618-10 and 618-11 Burial Ground Nonintrusive Characterization of Vertical Pipe Units Lessons Learned

Energy Technology Data Exchange (ETDEWEB)

Darby, J. W.

2012-06-28

A “lessons learned” is a noteworthy practice or innovative approach that is captured and shared to promote repeat application, or an adverse work practice/experience that is captured and shared to avoid reoccurrence. This document provides the lessons learned identified by the 618-10 Burial Ground trench remediation and the 618-10 and 618-11 Burial Ground nonintrusive characterization of the vertical pipe units (VPUs).

File list: Oth.Unc.10.Adenine_N6-methylation.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.Unc.10.Adenine_N6-methylation.AllCell ce10 TFs and others Adenine N6-methylatio...n Unclassified http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/Oth.Unc.10.Adenine_N6-methylation.AllCell.bed ...

Voltage manipulation of the magnetization reversal in Fe/n-GaAs/piezoelectric heterostructure

Energy Technology Data Exchange (ETDEWEB)

Li, Yuanyuan; Luo, Wengang; Zhu, Lijun; Zhao, Jianhua; Wang, Kaiyou, E-mail: kywang@semi.ac.cn

2015-02-01

We carefully investigated the in-plane magnetization reversal and corresponding magnetic domain structures in Fe/n-GaAs/piezoelectric heterostructure using longitudinal magneto-optical Kerr microscopy. The coexistence of the in-plane <100> cubic and [11{sup ¯}0] uniaxial magnetic anisotropy was observed in this system at virgin state. The piezo voltages can effectively manipulate the magnetic properties of the Fe/n-GaAs/piezoelectric heterostructure, where the manipulation of two-jump to one-jump magnetization switching during the magnetic reversal was achieved with magnetic field applied in [100] direction. Our findings on manipulation of ferromagnetization in this heterostructure could be important for future metal-semiconductor spintronic applications. The additional uniaxial anisotropy induced by piezo voltages obtained at ±75 V is ±1.4×10{sup 3} J/m{sup 3}. - Highlights: • In this work, we use piezo voltages not only realize the significant change of coercivity but also effectively manipulate the magnetization transition from one step to two steps during magnetic reversal, indicating that the piezo-voltages can be used to effectively control the magnetization reversal. • The additional uniaxial anisotropy induced by piezo voltages at +/−75 V are +/−1.4×10{sup 3} J/m{sup 3}. This work could be very used for future metal-semiconductor spintronic devices.

Dynamics of Excited State Proton Transfer in Nitro Substituted 10-Hydroxybenzo[h]quinolines

DEFF Research Database (Denmark)

Marciak, H; Hristova, S.; Deneva, V

2017-01-01

The ground state tautomerism and excited state intramolecular proton transfer (ESIPT) of 10-hydroxybenzo[h]quinoline (HBQ) and its nitro derivatives, 7-nitrobenzo[h]quinolin-10-ol (2) and 7,9-dinitrobenzo[h]quinolin-10-ol (3), have been studied in acetonitrile using steady state as well as time d...

46 CFR 153.12 - IMO Certificates for United States Ships.

Science.gov (United States)

2010-10-01

... 8, or the Officer in Charge, Marine Inspection, issues a United States ship an IMO Certificate... 46 Shipping 5 2010-10-01 2010-10-01 false IMO Certificates for United States Ships. 153.12 Section... CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS General § 153.12...

10 CFR 455.131 - State ranking of grant applications.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false State ranking of grant applications. 455.131 Section 455... State ranking of grant applications. (a) Except as provided by § 455.92 of this part, all eligible... audit or energy use evaluation pursuant to § 455.20(k). Each State shall develop separate rankings for...

Structural properties and superconductivity of SrFe2As2-xPx (0.0 ≤ x ≤ 1.0) and CaFe2As2-yPy (0.0 ≤ y ≤ 0.3)

International Nuclear Information System (INIS)

Shi, H L; Yang, H X; Tian, H F; Lu, J B; Wang, Z W; Qin, Y B; Song, Y J; Li, J Q

2010-01-01

The SrFe 2 As 2-x P x (0.0 ≤ x ≤ 1.0) and CaFe 2 As 2-y P y (0.0 ≤ y ≤ 0.3) materials were prepared by a solid-state reaction method. X-ray diffraction measurements indicate that the single-phase samples can be successfully obtained for SrFe 2 As 2-x P x (0.0 ≤ x ≤ 0.8) and CaFe 2 As 2-y P y (0.0 ≤ y ≤ 0.3). Visible contraction of the lattice parameters is determined due to the relatively smaller radius of P ions in comparison with that of As. The spin-density-wave (SDW) instability associated with the tetragonal to orthorhombic phase transition is suppressed noticeably in both systems following the increase in P content. The highest superconducting transitions are observed at about 27 K in SrFe 2 As 1.3 P 0.7 and at about 13 K in CaFe 2 As 1.925 P 0.075 , respectively. Structural analysis suggests that lattice contraction could notably affect the superconductivity in these materials.

49 CFR 24.208 - Aliens not lawfully present in the United States.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Aliens not lawfully present in the United States... Requirements § 24.208 Aliens not lawfully present in the United States. (a) Each person seeking relocation... of an individual, that he or she is either a citizen or national of the United States, or an alien...

Syntheses, characterization and antifungal activity of tris(1,10-phenanthroline)iron(II) bis(n-r-sulfonyldithiocarbimate)zincate(II)

Energy Technology Data Exchange (ETDEWEB)

Bottega, Fernanda C.; Oliveira, Marcelo R. L.; Garcia, Camila V.; Menezes, Daniele C.; Rubinger, Mayura M.M., E-mail: marcelor@ufv.br [Departamento de Quimica, Universidade Federal de Vicosa, MG (Brazil); Zambolim, Laercio [Departamento de Fitopatologia, Universidade Federal de Vicosa, MG (Brazil)

2013-09-01

Four new compounds with the general formula [Fe(phen){sub 3}][Zn(RSO{sub 2}N=CS{sub 2}){sub 2}], where phen = 1,10-phenanthroline, R = 4-FC{sub 6}H{sub 4}(1), 4-ClC{sub 6}H{sub 4} (2), 4-BrC{sub 6}H{sub 4} (3) and 4-IC{sub 6}H{sub 4} (4), respectively, were obtained by the reaction of the appropriate potassium N-R-sulfonyldithiocarbimate (RSO{sub 2}N=CS{sub 2}K{sub 2}) and tris(1,10-phenanthroline)iron(II) sulfate, with zinc(II) acetate dihydrate in dimethylformamide. The elemental analyses and the IR data were consistent with the formation of the expected complexes salts. The {sup 1}H and {sup 13}C NMR spectra showed the signals for the cationic iron(II) complex and dithiocarbamate moieties. The molar conductance data were consistent with the 1:1 cation:anion complexes in 1-4. The antifungal activities of the compounds were tested in vitro against Candida albicans, Candida tropicalis and Colletotrichum gloeosporioides. (author)

Hyperfine fields of Fe in Nd2Fe14BandSm2Fe17N3

Science.gov (United States)

Akai, Hisazumi; Ogura, Masako

2015-03-01

High saturation magnetization of rare-earth magnets originates from Fe and the strong magnetic anisotropy stems from f-states of rare-earth elements such as Nd and Sm. Therefore the hyperfine fields of both Fe and rare-earth provide us with important pieces of information: Fe NMR enable us to detect site dependence of the local magnetic moment and magnetic anisotropy (Fe sites also contribute to the magnetic anisotropy) while rare-earth NQR directly give the information of electric field gradients (EFG) that are related to the shape of the f-electron cloud as well as the EFG produced by ligands. In this study we focus on the hyperfine fields of materials used as permanent magnets, Nd2Fe14BandSm2Fe17N3 from theoretical points of view. The detailed electronic structure together with the hyperfine interactions are discussed on the basis of the first-principles calculation. In particular, the relations between the observed hyperfine fields and the magnetic properties are studies in detail. The effects of doping of those materials by other elements such as Dy and the effects of N adding in Sm2Fe17N3 will be discussed. This work was supported by Elements Strategy Initiative Center for Magnetic Materials Project, the Ministry of Education, Culture, Sports, Science and Technology, Japan.

Probing the A1 to L10 transformation in FeCuPt using the first order reversal curve method

Directory of Open Access Journals (Sweden)

Dustin A. Gilbert

2014-08-01

Full Text Available The A1-L10 phase transformation has been investigated in (001 FeCuPt thin films prepared by atomic-scale multilayer sputtering and rapid thermal annealing (RTA. Traditional x-ray diffraction is not always applicable in generating a true order parameter, due to non-ideal crystallinity of the A1 phase. Using the first-order reversal curve (FORC method, the A1 and L10 phases are deconvoluted into two distinct features in the FORC distribution, whose relative intensities change with the RTA temperature. The L10 ordering takes place via a nucleation-and-growth mode. A magnetization-based phase fraction is extracted, providing a quantitative measure of the L10 phase homogeneity.

2,9-Dimethyl-1,10-phenanthrolin-1-ium tetrachloridoferrate(III methanol monosolvate

Directory of Open Access Journals (Sweden)

Ehsan Bahojb Noruzi

2012-07-01

Full Text Available In the title compound, (C14H13N2[FeCl4]·CH3OH, the 2,9-dimethyl-1,10-phenanthrolin-1-ium cation, FeCl4− anion and methanol solvent molecule lie on a twofold rotation axis. Due to symmetry, the H atom on the N atom of the cation is half-occupied. In the anion, the FeIII atom has a tetrahedral geometry. H atoms of the methanol molecule are disordered over two sets of sites around the twofold axis. In the crystal, π–π contacts between the pyridine rings and between the pyridine and benzene rings [centroid–centroid distances = 3.6535 (16 and 3.5522 (17 Å] and intermolecular O—H...N and N—H...O hydrogen bonds stabilize the structure.

19 CFR 10.242 - Definitions.

Science.gov (United States)

2010-04-01

... “beneficiary country” as defined in § 10.202(a) for purposes of the ATPA which the President also has... articles under 19 U.S.C. 3203(b)(3) and which has been the subject of a determination by the President or... entered into by the United States, Canada, and Mexico on December 17, 1992. Preferential treatment...

Production of 26Al by spallation of Fe, Si, Al nuclei

International Nuclear Information System (INIS)

Paillard, P.

1977-01-01

Cross sections for 7 Be, 10 Be and 26 Al formation in Al, Si and Fe targets bombarded with 0.6 and 24GeV protons have been measured by using highly selective chemical separation and low level background counters. Results for 26 Al at 0.6GeV are in mb: 17.9 + or - 2.7 in Al, 12.5 + or - 2.5 in Si and 0.45 + or - 0.14 in Fe; at 24GeV 2.6 + or - 0.5mb in Fe. Results for 10 Be are not valid on account of experimental difficulties. It is deduced from these values of aluminium in cosmic ray propagation that 26 Al is not yet cosmic ray chronometer [fr

CompTIA Network+ Review Guide Exam N10-005

CERN Document Server

Ferguson, Bill

2012-01-01

Fast, focused review for the latest CompTIA Network+ Exam N10-005 CompTIA's Network+ certification is the leading non-vendor networking certification in the world and has become the standard certification for networking professionals. Make sure you're ready for CompTIA's new Network+ certification (exam N10-005) with this new edition of Sybex's CompTIA Network+ Review Guide. This concise guide is efficiently organized by exam objectives and covers all five exam domains. The book also includes 50 chapter review questions, as well as access to two online practice exams, and much more. It's the p

Heterobimetallic [NiFe] Complexes Containing Mixed CO/CN- Ligands: Analogs of the Active Site of the [NiFe] Hydrogenases.

Science.gov (United States)

Perotto, Carlo U; Sodipo, Charlene L; Jones, Graham J; Tidey, Jeremiah P; Blake, Alexander J; Lewis, William; Davies, E Stephen; McMaster, Jonathan; Schröder, Martin

2018-03-05

The development of synthetic analogs of the active sites of [NiFe] hydrogenases remains challenging, and, in spite of the number of complexes featuring a [NiFe] center, those featuring CO and CN - ligands at the Fe center are under-represented. We report herein the synthesis of three bimetallic [NiFe] complexes [Ni( N 2 S 2 )Fe(CO) 2 (CN) 2 ], [Ni( S 4 )Fe(CO) 2 (CN) 2 ], and [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] that each contain a Ni center that bridges through two thiolato S donors to a {Fe(CO) 2 (CN) 2 } unit. X-ray crystallographic studies on [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ], supported by DFT calculations, are consistent with a solid-state structure containing distinct molecules in the singlet ( S = 0) and triplet ( S = 1) states. Each cluster exhibits irreversible reduction processes between -1.45 and -1.67 V vs Fc + /Fc and [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] possesses a reversible oxidation process at 0.17 V vs Fc + /Fc. Spectroelectrochemical infrared (IR) and electron paramagnetic resonance (EPR) studies, supported by density functional theory (DFT) calculations, are consistent with a Ni III Fe II formulation for [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] + . The singly occupied molecular orbital (SOMO) in [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] + is based on Ni 3d z 2 and 3p S with the S contributions deriving principally from the apical S-donor. The nature of the SOMO corresponds to that proposed for the Ni-C state of the [NiFe] hydrogenases for which a Ni III Fe II formulation has also been proposed. A comparison of the experimental structures, and the electrochemical and spectroscopic properties of [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] and its [Ni( N 2 S 3 )] precursor, together with calculations on the oxidized [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] + and [Ni( N 2 S 3 )] + forms suggests that the binding of the {Fe(CO)(CN) 2 } unit to the {Ni(CysS) 4 } center at the active site of the [NiFe] hydrogenases suppresses thiolate-based oxidative chemistry involving the bridging thiolate S donors

Synthesis and Electronic Structure of Dissymmetrical, Naphthalene-Bridged Sandwich Complexes [Cp ' Fe(mu-C10H8)MCp*](x) (x=0,+1; M = Fe, Ru; Cp ' = eta(5)-C5H2-1,2,4-tBu(3); Cp* = eta(5)-C5Me5)

NARCIS (Netherlands)

Malberg, J.; Lupton, E.; Schnöckelborg, E.M.; de Bruin, B.; de Sutter, J.; Meyer, K.; Hartl, F.; Wolf, R.

2013-01-01

The dissymmetrical naphthalene-bridged complexes [Cp'Fe(mu-C10H8)FeCp*] (3; Cp* = eta(5)-C5Me5, Cp' = eta(5)-C5H2-1,2,4-tBu(3)) and [Cp'Fe(mu-C10H8)RuCp*] (4) were synthesized via a one-pot procedure from FeCl2(thf)(1.5), Cp'K, KC10H8, and [Cp*FeCl(tmeda)] (tmeda =

Mössbauer spectroscopy and DFT calculations on all protonation states of the 2Fe-2S cluster of the Rieske protein

Science.gov (United States)

Müller, C. S.; Auerbach, H.; Stegmaier, K.; Wolny, J. A.; Schünemann, V.; Pierik, A. J.

2017-11-01

The Thermus thermophilus Rieske protein ( TtRP) contains a 2Fe-2S cluster with one iron (Fe-Cys) coordinated by four sulfur atoms (2xS2- and 2xCys) and one iron (Fe-His) by two sulfur and two nitrogen atoms (2xS2-, His134 and His154). Here, the protein is investigated at three pH values (6.0, 8.5 and 10.5) in order to elucidate the protonation states of the His-ligands. Examination of the effect of protonation on the electronic structure of the cluster via Mössbauer spectroscopy gives a deeper understanding of the coupling of electron transfer to the protonation state of the His-ligands. Two components (1 referring to Fe-Cys and 2 to Fe-His) with parameters typical for a diamagnetic [2Fe-2S]2+ cluster are detected. The Mössbauer parameters and the protonation state clearly correlate: while δ remains almost pH-independent with δ 1 (pH6.0) = 0.23 (± 0.01) mms- 1 and δ 1 (pH10.5) = 0.24 (± 0.01) mms- 1 for Fe-Cys, it decreases for Fe-His from δ 2 (pH6.0) = 0.34 (± 0.01) mms- 1 to δ 2 (pH10.5) = 0.28 (± 0.01) mms- 1. Δ E Q changes from Δ E Q1 (pH6.0) = 0.57 (± 0.01) mms- 1 to Δ E Q1 (pH10.5) = 0.45 (± 0.01) mms- 1 and from Δ E Q2 (pH6.0) = 1.05 (± 0.01) mms- 1 to Δ E Q2 (pH10.5) = 0.71 (± 0.01) mms- 1. Density functional theory (DFT)-calculations based on the crystal structure (pdb 1NYK) (Hunsicker-Wang et al. Biochemistry 42, 7303, 2003) have been performed for the Rieske-cluster with different His-ligand protonation states, reproducing the experimentally observed trend.

29 CFR 3.10 - Methods of payment of wages.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Methods of payment of wages. 3.10 Section 3.10 Labor Office... IN WHOLE OR IN PART BY LOANS OR GRANTS FROM THE UNITED STATES § 3.10 Methods of payment of wages. The payment of wages shall be by cash, negotiable instruments payable on demand, or the additional forms of...

Pressure induced magnetic phase transition in RhFe{sub 3}N and IrFe{sub 3}N: An ab-initio study

Energy Technology Data Exchange (ETDEWEB)

Puvaneswari, S. [Department of physics, E.M.G.Yadava women’s college, Madurai, Tamilnadu-625014 (India); Manikandan, M. [Department of physics, N.M.S.S.V.N college, Madurai, Tamilnadu-625019 (India); Rajeswarapalanichamy, R., E-mail: rrpalanichamy@gmail.com

2016-05-06

The structural, electronic, elastic and magnetic properties of RhFe{sub 3}N and IrFe{sub 3}N are investigated using ab-initio calculations based on density functional theory as implemented in VASP code within the gradient generalized approximation. The non-spin polarized and spin polarized calculations are performed for these nitrides at normal and high pressures. It is found that these ternary nitrides are stable in ferromagnetic state at normal pressure. The lattice constant and bulk modulus values are calculated. The electronic structure reveals that these nitrides are metallic at normal pressure. The calculated elastic constants indicate that they are mechanically stable at ambient pressure. Ferromagnetic to nonmagnetic phase transition is observed in RhFe{sub 3}N and IrFe{sub 3}N at high pressure. Ferromagnetism is quenched in these nitrides at high pressure.

N-anti N oscillation in SO(10) and SU(6) supersymmetric grand unified models

International Nuclear Information System (INIS)

Fujimoto, Y.; Zhiyong, Z.

1982-06-01

N-anti N oscillation in SO(10) and SU(6) S.G.U.M. is considered. We find a new type of diagram leading to a faster oscillation rate than in non-supersymmetric case. It is also noted that in SO(10) S.G.U.M. with intermediate SU(4)sub(C)xSU(2)sub(L)xSU(2)sub(R) symmetry N-anti N oscillation would be highly suppressed, which may not necessarily be the case for SU(6) S.G.U.M. (author)

Structure, nonstoichiometry, sintering and oxygen permeability of perovskite SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jin Na [College of Chemistry and Materials Science, Liaoning University of Petroleum and Chemical Technology, Fushun 113001 (China); State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Lu, Hui, E-mail: huilu@dicp.ac.cn [Greenhouse Gas Research Center, Climate Change Technology Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of); State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Gui, Jian Zhou [College of Chemistry and Materials Science, Liaoning University of Petroleum and Chemical Technology, Fushun 113001 (China); Kim, Jong Pyo; Son, Sou Hwan [Greenhouse Gas Research Center, Climate Change Technology Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of); Park, Jung Hoon, E-mail: pjhoon@kier.re.kr [Greenhouse Gas Research Center, Climate Change Technology Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of)

2013-04-20

Highlights: ► The novel Fe/Nb co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides were characterized by the XRD, DSC, TG and SEM–EDS. ► The high structural stability of the co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides. ► The excellent oxygen permeation performance of the co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.10) membrane. -- Abstract: The novel Fe/Nb co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides have been synthesized and characterized by X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetry (TG), and scanning electron microscopy (SEM). The XRD and DSC results demonstrate that the structural stability of the Fe/Nb co-substituted samples x = 0.05, 0.10 is improved greatly compared to the sample x = 0.00. The Fe/Nb co-doping in the SrCoO{sub 3−δ} oxide results in the improved structural stability of the SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides. The nonstoichiometric and sintering properties were investigated by TG and SEM, and the oxygen permeation fluxes were measured at 800–950 °C for the sample x = 0.10. The improved oxygen permeability of the ceramic SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.10) membrane compared to the (Ba{sub 0.5}Sr{sub 0.5})(Co{sub 0.8}Fe{sub 0.2})O{sub 3−δ} and SrCo{sub 0.8}Fe{sub 0.2}O{sub 3–δ} membranes, was observed under an air/He oxygen partial pressure gradient at 800–950 °C.

Electron states at electrolyte/n-GaN and electrolyte/n-InGaN interfaces

Energy Technology Data Exchange (ETDEWEB)

Rudinsky, M. E., E-mail: rudinskym@mail.ru; Gutkin, A. A.; Brunkov, P. N. [Russian Academy of Sciences, Ioffe Physical-Technical Institute (Russian Federation)

2012-06-15

The differential capacitance and differential active conductance of rectifying contacts of n-GaN and n-In{sub x}Ga{sub 1-x}N (x Almost-Equal-To 0.15) with an electrolyte (0.2 M aqueous solutions of NaOH, NaCl, or HCl) have been studied. It was found that electron states with energies corresponding to the upper half of the energy gap of a semiconductor exist at the interface between these semiconductors and a NaOH solution. The density and characteristic recharging time of states noticeably contributing to the differential capacitance and differential active conductance at probe-voltage frequencies of 0.3-1 kHz grow with their binding energy and, for states lying at 0.15-0.3 eV below the conduction-band bottom of n-GaN, fall within the ranges 10{sup 12}-2 Multiplication-Sign 10{sup 13} cm{sup -2} eV{sup -1} and 10{sup -4}-10{sup -2} s, respectively. For contacts with NaCl and HCl solutions, there are no states of this kind. It is assumed that the observed states are related to the adsorption of hydroxyl groups.

A study on magnetoelastic properties of Tb3 (Fe28-xCox) V1.0 (x=0, 3, 6) compounds

International Nuclear Information System (INIS)

Gholizadeh, A.; Tajabor, N.; Pourarian, F.

2012-01-01

In this work, The magnetoelastic properties of polycrystalline samples of Tb 3 (Fe 28-x Co x ) V 1.0 (x=0, 3, 6) intermetallic compounds are investigated by means of linear thermal expansion and magnetostriction measurements in the temperature range of 77-515 K under applied magnetic fields up to 1.5 T. The linear thermal expansion increases with the Co content. The well-defined anomalies observed in the linear thermal expansion coefficients for Tb 3 (Fe 28-x Co x ) V 1.0 (x=0, 3, 6) compounds are associated with the magnetic ordering temperature for x=0 and spin reorientation temperatures for x=3, 6. Below transition temperatures, the value of the longitudinal magnetostriction (λ Pa ) at 1.6 T increases with Co content.

A study of the higher excitation levels of 11B via the 10B(n,n)10B and 10B(n,n')10B*(0.72, 1.74, 2.15, 3.59, 4.77 MeV) reactions

International Nuclear Information System (INIS)

Sadowski, E.T.

1988-11-01

As part of the study of the higher energy-level structure of 11 B, cross sections for elastic and inelastic scattering of neutrons from isotopically enriched 10 B samples have been measured for incident neutron energies from 3.03 MeV to 6.45 MeV in 250 keV increments and from 7.02 MeV to 12.01 MeV in 500 keV increments. Inelastic angular distributions for scattering to the states in parentheses in 10 B have been measured from the indicated energy up to 12.01 MeV; (0.718) from 3.02 MeV; (1.74) from 3.27 MeV; (2.15) from 3.77 MeV; (3.59) from 5.52 MeV; (4.77) from 7.02 MeV. The measurements at 3.02, 3.51, 4.02, and 4.51 MeV were done at nine laboratory angles from 20/degree/ to 158/degree/ in 17.5/degree/ increments with a sample that is isotopically 95.86% 10 B. All other distributions measured scattering at 11 laboratory angles from 18/degree/ to 158/degree/ in 15/degree/ increments from a sample that is isotopically 99.49% 10 B. The data are corrected for air scattering, sample attenuation, minor isotope impurity, multiple scattering, and elastic and inelastic scattering from the sample of the neutron source continuum and contaminants. An eight-channel, multilevel R-matrix analysis was performed on the data. Level energies, spins, and parities were deduced for twelve levels above 13 MeV excitation in 11 B. Only two definite and three tentative assignments for T = /1/2/ levels had been made previously above 13 MeV. The two definite levels were confirmed. Good agreement between the data and the R-matrix calculation in all analyzed channels was obtained for the proposed structure. 122 refs., 40 figs., 7 tabs

The anisotropy field of FePt L10 nanoparticles controlled by very thin Pt layer

International Nuclear Information System (INIS)

Okamoto, Satoshi; Kitakami, Osamu; Kikuchi, Nobuaki; Miyazaki, Takamichi; Shimada, Yutaka; Chiang, Te-Hsuan

2004-01-01

We have prepared epitaxial FePt L1 0 (001) nanoparticles covered with Pt [d Pt nm]/Ag[(4-d Pt ) nm] overlayers. The particles are oblate spheroids approximately 10 nm in diameter and 2 nm in height. The anisotropy field H k at 0 K, which is evaluated from the temperature dependences of coercivity H c , decreases from 90 to 60 kOe on increasing the Pt thickness from d Pt 0 to 1.5 nm, while the energy barrier at zero field remains unchanged. The significant reduction of H k due to the presence of the adjacent Pt layer can be attributed to an enhanced magnetic moment caused by the ferromagnetic polarization of Pt atoms at the interface. This finding suggests an effective method of controlling the switching field of FePt L1 0 nanoparticles

37 CFR 10.33 - Direct contact with prospective clients.

Science.gov (United States)

2010-07-01

... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Direct contact with prospective clients. 10.33 Section 10.33 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND... clients. A practitioner may not solicit professional employment from a prospective client with whom the...

Does the ground-state resonance of 10Li overlap neutron threshold

International Nuclear Information System (INIS)

McVoy, K.W.; Van Isacker, P.

1994-01-01

Recent measurements suggest that the ground state of 10 Li is a resonance which may well be wide enough to overlap the (n + 9 Li) threshold. In this context we recall some of the curious properties of resonances located near threshold and entered from a non-decay channel, including their asymmetry and the fact that the peak observed in the cross section occurs at neither the R-matrix nor the S-matrix energy, but rather between the two. Because of these and other complications, it does not seem likely that either the l-value of the resonance or the energy of the corresponding state can accurately be determined form the shape of the resonance peak alone. (authors). 5 refs., 4 figs., 2 tabs

Ferromagnetism versus slow paramagnetic relaxation in Fe-doped Li3N

Science.gov (United States)

Fix, M.; Jesche, A.; Jantz, S. G.; Bräuninger, S. A.; Klauss, H.-H.; Manna, R. S.; Pietsch, I. M.; Höppe, H. A.; Canfield, P. C.

2018-02-01

We report on isothermal magnetization, Mössbauer spectroscopy, and magnetostriction as well as temperature-dependent alternating-current (ac) susceptibility, specific heat, and thermal expansion of single crystalline and polycrystalline Li2(Li1 -xFex) N with x =0 and x ≈0.30 . Magnetic hysteresis emerges at temperatures below T ≈50 K with coercivity fields of up to μ0H =11.6 T at T =2 K and magnetic anisotropy energies of 310 K (27 meV). The ac susceptibility is strongly frequency-dependent (f =10 -10 000 Hz) and reveals an effective energy barrier for spin reversal of Δ E ≈1100 K (90 meV). The relaxation times follow Arrhenius behavior for T >25 K . For T <10 K , however, the relaxation times of τ ≈1010 s are only weakly temperature-dependent, indicating the relevance of a quantum tunneling process instead of thermal excitations. The magnetic entropy amounts to more than 25 J molFe-1 K-1, which significantly exceeds R ln 2 , the value expected for the entropy of a ground-state doublet. Thermal expansion and magnetostriction indicate a weak magnetoelastic coupling in accordance with slow relaxation of the magnetization. The classification of Li2(Li1 -xFex) N as ferromagnet is stressed and contrasted with highly anisotropic and slowly relaxing paramagnetic behavior.

State nuclear initiatives in the United States

International Nuclear Information System (INIS)

Strauss, P.L.; Stoiber, C.R.

1977-01-01

The paper deals with State nuclear initiatives regarding the role of nuclear power in the energy future of the United States. The question of whether and under what circumstances nuclear facilities should be used to generate electricity was put to the popular vote in several States in 1976. Some general principles of Federal-State relations are discussed with specific reference to nuclear regulations. The initiative mechanism itself is described as well as its legal form and background. The parallel developments in the State and Federal legislative consideration of nuclear issues is reviewed and the suggested reasons for the defeat of the proposals in the seven States concerned are discussed. Finally, the author draws some conclusions on the effects of the 1976 initiatives on future decision-making in the US on energy policy in general and nuclear power in particular. (NEA) [fr

40 CFR Appendix A to Subpart II of... - States With Approved State Implementation Plan Revisions Concerning CAIR NOX Opt-In Units

Science.gov (United States)

2010-07-01

... under § 97.188(b): Indiana Michigan North Carolina Ohio South Carolina Tennessee 2. The following States... allocation of CAIR NOX allowances to such units under § 97.188(c): Indiana Michigan Ohio North Carolina South Carolina Tennessee [65 FR 2727, Jan. 18, 2000, as amended at 72 FR 46394, Aug. 20, 2007; 72 FR 56920, Oct...

Morphology-controlled synthesis and novel microwave electromagnetic properties of hollow urchin-like chain Fe-doped MnO2 under 10 T high magnetic field

International Nuclear Information System (INIS)

Yuping, Duan; Jia, Zhang; Hui, Jing; Shunhua, Liu

2011-01-01

Fe-doped MnO 2 with a hollow sea urchin-like ball chain shape was first synthesized under a high magnetic field of 10 T. The formation mechanism was investigated and discussed in detail. The synthesized samples were characterized by XRD, SEM, TEM, EMPA, and vector network analysis. By doping MnO 2 with Fe, the relative complex permittivity of MnO 2 and its corresponding loss tangent clearly decreases, but its relative complex permeability and its corresponding loss tangent markedly increases. Moreover, the theoretically calculated values of reflection loss show that with increasing the Fe content, the as-prepared Fe-doped MnO 2 exhibits good microwave absorption capability. -- Graphical Abstract: Fe-doped MnO 2 with a hollow sea urchin-like ball chain shape was first synthesized in a high magnetic field of 10 T via a simple chemical process. Display Omitted Highlights: → Fe-doped MnO 2 with a hollow sea urchin-like ball chain shape was first synthesized. → We investigated formation mechanism and electromagnetic properties of the Fe-doped MnO 2 . → By doping MnO 2 with Fe, the electromagnetic properties are improved obviously.

NMR study of the molecular nanomagnet [Fe8(N3C6H15)6O2(OH)12]·[Br8·9H2O] in the high-spin magnetic ground state

International Nuclear Information System (INIS)

Furukawa, Y.; Kumagai, K.; Lascialfari, A.; Aldrovandi, S.; Borsa, F.; Sessoli, R.; Gatteschi, D.

2001-01-01

The magnetic molecular cluster [Fe 8 (N 3 C 6 H 15 ) 6 O 2 (OH) 12 ] 8+ [Br 8 ·9H 2 O] 8- , in short Fe8, has been investigated at low temperature by 1 H-NMR and relaxation measurements. Some measurements of 2 D-NMR in partially deuterated Fe8 clusters will also be reported. Upon decreasing temperature the NMR spectra display a very broad and structured signal which is the result of the internal local fields at the proton sites due to the local moments of the Fe(III) ions in the total S=10 magnetic ground state. The proton and deuteron NMR spectra have been analyzed and the different resonance peaks have been attributed to the different proton groups in the molecule. The simulation of the spectra by using a dipolar hyperfine field and the accepted model for the orientation of the Fe(III) local moments do not agree with the experiments even when the magnitude of the local Fe(III) moments is allowed to vary. It is concluded that a positive contact hyperfine interaction of the same order of magnitude as the dipolar interaction is present for all proton sites except the water molecules. The temperature and magnetic field dependence of the nuclear spin-lattice relaxation rate is ascribed to the fluctuations of the local Fe(III) moments, which follow rigidly the fluctuations of the total ground state magnetization of the nanomagnet. By using a simple model already utilized for the Mn12 cluster, we derive the value of the spin phonon coupling constant which determines the lifetime broadening of the different magnetic quantum number m substates of the S=10 ground state. It is shown that the lifetime broadening decreases rapidly on lowering the temperature. When the lifetime becomes longer than the reciprocal of the frequency shift of the proton lines a structure emerges in the NMR spectrum reflecting the ''frozen'' local moment configuration

39 CFR 230.10 - What do these rules govern?

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false What do these rules govern? 230.10 Section 230.10 Postal Service UNITED STATES POSTAL SERVICE ORGANIZATION AND ADMINISTRATION OFFICE OF INSPECTOR GENERAL Rules Governing Compliance With Subpoenas, Summonses, and Court Orders by Postal Employees Within the...

Theoretical emission line ratios for [Fe III] and [Fe VII] applicable to the optical and infrared spectra of gaseous nebulae.

Science.gov (United States)

Keenan, F P; Aller, L H; Ryans, R S; Hyung, S

2001-08-14

Recent calculations of electron impact excitation rates and Einstein A-coefficients for transitions among the 3d(6) levels of Fe III and among the 3d(2) levels of Fe VII are used to derive theoretical emission line ratios applicable to the optical and infrared spectra of gaseous nebulae. Results for [Fe III] are generated for electron temperatures T(e) = 7,000-20,000 K and densities N(e) = 10(2)-10(8) cm(-3), whereas those for [Fe VII] are provided for T(e) = 10,000-30,000 K and N(e) = 10(2)-10(8) cm(-3). The theoretical line ratios are significantly different in some instances from earlier calculations and resolve discrepancies between theory and observation found for the planetary nebulae IC 4997 and NGC 7027.

78 FR 39279 - United States Department of Energy; Bonneville Power Administration; Notice of Petition for...

Science.gov (United States)

2013-07-01

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. NJ13-10-000] United States Department of Energy; Bonneville Power Administration; Notice of Petition for Declaratory Order Take notice... (OATT) and a Petition for Declaratory Order requesting the Commission find that Bonneville's OATT, as...

Evolución de las propiedades mecánicas con la temperatura de cintas amorfas Mg10Ni10Y

Directory of Open Access Journals (Sweden)

Torrijos, M. A.

2006-02-01

Full Text Available The mechanical behaviour by tensile strength test from room temperature to 350 ºC in the rapidly solidified Mg-10Ni-10Y (at. % ribbon has been studied. To determine the effect of yttrium additions the results are compared with those of Mg-11Ni studied in a previous work. Before studding the mechanical behavior of the material the thermal stability of the amorphous ribbon and the crystallization reactions were determined by DSC experiments. Results show that yttrium stabilizes the amorphous phase but it has not reinforcement effect. The tensile strength and elongation to failure values of the ternary alloy are lower than those of Mg-11Ni

El objetivo de este estudio es la caracterización mecánica, mediante ensayos de tracción, desde temperatura ambiente hasta 350 °C, de una aleación amorfa de composición Mg-10Ni-10Y (% at. obtenida mediante solidificación rápida por la técnica de la rueda. Se analiza la influencia de la adición de itrio al Mg-Ni para lo cual los resultados se comparan con los de la aleación binaria Mg-11Ni estudiada previamente. Antes de iniciar la caracterización mecánica del material, se realizó un estudio mediante calorimetría diferencial de barrido para comprobar la naturaleza amorfa de la cinta, analizar su estabilidad térmica y conocer las transformaciones que experimenta hasta la cristalización. Los resultados indican que el itrio es un estabilizador de la fase amorfa pero no mejora las propiedes mecánicas de la cinta binaria. Los valores de resistencia mecánica y alargamiento a rotura medidos en la cinta con itrio son menores que los obtenidos para la aleación binaria.

49 CFR 565.14 - Motor vehicles imported into the United States.

Science.gov (United States)

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Motor vehicles imported into the United States...) REQUIREMENTS VIN Requirements § 565.14 Motor vehicles imported into the United States. (a) Importers shall utilize the VIN assigned by the original manufacturer of the motor vehicle. (b) All passenger cars...

1 CFR 11.4 - The United States Government Manual.

Science.gov (United States)

2010-01-01

... Documents under the general direction of the Administrative Committee. The online edition of the Manual... Government Printing Office (44 U.S.C. 4101). [54 FR 9677, Mar. 7, 1989, as amended at 58 FR 64872, Dec. 10...

On the eletronic structure of Be sub(n) (3 < = n < = 10) clusters

International Nuclear Information System (INIS)

Camargo, F.P.; Vianna, J.D.M.

The electronic configurations, bonding energies and molecular orbital energies of Be(sub n) (n = 3, 4, 6, 10) have been calculated by the SCF-MO-CNDO theory parametrized by Boyd and Whitehead (CNDO/BW). Comparisons are made with the theoretical results which are available. (Author) [pt

46 CFR 30.10-50 - Pilot boarding equipment and point of access.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Pilot boarding equipment and point of access. 30.10-50... Definitions § 30.10-50 Pilot boarding equipment and point of access. (a) Pilot boarding equipment means a... boarding equipment. [CGD 79-032, 49 FR 25455, June 21, 1984] ...

40 CFR 130.10 - State submittals to EPA.

Science.gov (United States)

2010-07-01

... QUALITY PLANNING AND MANAGEMENT § 130.10 State submittals to EPA. (a) The following must be submitted...)(1). (Approved by the Office of Management and Budget under control number 2040-0071) (3) Total maximum daily loads (TMDLs) (303(d)); and (4) Water quality management (WQM) plan and certified and...

75 FR 8391 - Assisted Living Conversion Program (ALCP) and Emergency Capital Repair Program (ECRP)

Science.gov (United States)

2010-02-24

... Conversion Program (ALCP) provides funding for the physical costs of converting some or all the units of an... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5376-N-10] Assisted Living Conversion... rehabilitate, modernize, or retrofit aging structure, common areas, or individual dwelling units through the...

Detection of neutrons of intermediate energy using 10B, enclosed in a coaxial Ge(Li) counter

International Nuclear Information System (INIS)

Huck, A.; Klotz, G.; Walter, G.

1976-01-01

A neutron detector operating in the energy range 1keV to roughly 1MeV with a time response that is fast enough to be used in time-of-flight experiments, has been designed and built. The neutron is absorbed in boron-10, placed inside a coaxial Ge(Li) counter. Efficient detection of the 478keV line from 7 Li, resulting from 10 B(n,α) 7 Li*, is realized. At the same time, the measurement of accompanying γ radiations, emitted by the neutron source, can be performed. Examples of results, obtained using (p,nγ) reactions, are given [fr

Caracterización metálica de material particulado PM10 en la atmósfera de Fonseca, La Guajira, Colombia

OpenAIRE

Carlos Doria Argumedo

2017-01-01

Teniendo en cuenta  la importancia del efecto sobre la salud de las partículas inhalables PM10 y los metales asociados a ellas, se evaluaron los niveles de  metales: Al, Cr, V, As, Se, Na, K, Mg, Ca, Bi, Fe, Hg y Pb, generados por fuentes naturales como el aerosol marino y la re-suspensión del suelo; y de fuentes antropogénicas como las actividades mineras de carbón y la circulación vehicular, en Fonseca, La Guajira, Colombia, Las muestras fueron colectadas en dos sitios cercanos al complejo ...

Ion-beam mixing and solid-state reaction in Zr-Fe multilayers

International Nuclear Information System (INIS)

Paesano, A. Jr.; Motta, A.T.; Birtcher, R.C.; Ryan, E.A.; Teixeira, S.R.; Bruckmann, M.E.; Amaral, L.

1997-01-01

Vapor-deposited Zr-Fe multilayered thin films with various wavelengths and of overall composition either 50% Fe or Fe-rich up to 57% Fe were either irradiated with 300 keV Kr ions at temperatures from 25 K to 623 K to fluences up to 2 x 10 16 cm -2 , or simply annealed at 773 K in-situ in the Intermediate Voltage Electron microscope At Argonne National Laboratory. Under irradiation, the final reaction product is the amorphous phase in all cases studied, but the dose to amorphization depends on the temperature and on the wavelength. In the purely thermal case (annealing at 773 K), the 50-50 composition produces the amorphous phase but for the Fe-rich multilayers the reaction products depend on the multilayer wavelength. For small wavelength, the amorphous phase is still formed, but at large wavelength the Zr-Fe crystalline intermetallic compounds appear. These results are discussed in terms of existing models of irradiation kinetics and phase selection during solid state reaction

B10(n,α)Li7 irradiation effects on high impact polystyrene

International Nuclear Information System (INIS)

Gupta, M.C.; Bansod, V.P.

1984-01-01

Irradiation effects of B 10 (n,α)Li 7 charged particles on high impact polystyrene were compared with those of Co 60 γ-rays, from the viewpoint of linear energy transfer (LET). For irradiation in air, the G values of crosslinks and main-chain scissions, G(X) and G(S) are 0.018 and 0.06, respectively, for γ-rays of low LET (ca. 0.22 eV/nm). Charged particles [B 10 (n,α)Li 7 ] of high LET (ca. 280 eV/nm) increase the G(X) value to 0.15 but G(S) is not much affected. All these findings are explained qualitatively by a difference in the distribution of energy deposition and the mechanism involving the competition between the deactivation of an excited molecule by the collision with ground state molecules and the macroradical formation by the bimolecular reaction of the excited molecules. These excited molecules in HIPS might be produced more closely to one another by charged particles than by γ-rays. (author)

Study of the double charge-changing collision cross-sections of H+, D+, Li+ ions with organic molecules in the energy range 10-50 keV

International Nuclear Information System (INIS)

Farrokhi, S.

1966-01-01

The variation of the double charge-changing collision cross-sections of H + , D + , Li + ions with organic molecules (CH 4 , C 2 H 6 , C 3 H 8 , C 4 H 10 ) in the energy range 10-50 keV has been studied. Several maximums for σ 1-1 = f(E) have been shown. Their existence should be explained by the different possibilities of dissociating the target-molecules. The position of the maximums, for the H + → H - and D + → D - reactions is in good agreement with that defined by the Massey adiabatic relation. (author) [fr

Diffusion of N adatoms on the Fe(100) surface

DEFF Research Database (Denmark)

Pedersen, M. Ø.; Österlund, L.; Mortensen, Jens Jørgen

2000-01-01

The diffusion of individual N adatoms on Fe(100) has been studied using scanning tunneling microscopy and ab initio density functional theory (DFT) calculations. The measured diffusion barrier for isolated N adatoms is E-d = (0.92 +/- 0.04) eV, with a prefactor of nu(0) = 4.3 x 10(12) s(-1), which...... is in quantitative agreement with the DFT calculations. Thr; diffusion is strongly coupled to lattice distortions. and. as a consequence, the presence of other N adatoms introduces an anisotropy in the diffusion. Based on experimentally determined values of the diffusion barriers and adsorbate......-adsorbate: interactions, the potential energy surface experienced by a N adatom is determined....

The Kepler-10 planetary system revisited by HARPS-N

DEFF Research Database (Denmark)

Dumusque, Xavier; Bonomo, Aldo S.; Haywood, Raphaelle D.

2014-01-01

-N Collaboration decided to observe Kepler-10 intensively with the HARPS-N spectrograph on the Telescopio Nazionale Galileo on La Palma. In total, 148 high-quality radial-velocity measurements were obtained over two observing seasons. These new data allow us to improve the precision of the mass determination...

First 3- excited state of 56Fe

International Nuclear Information System (INIS)

Fotiades, N.; Nelson, R. O.; Devlin, M.

2010-01-01

There is no reliable evidence for the existence of the 3.076 MeV (3 - ) level adopted in the ENSDF evaluation for 56 Fe although it has been reported in a few experiments. Previous reports of the observation of this level appear to be based on an incorrect assignment in early (e,e ' ) work. Recent neutron inelastic scattering measurements by Demidov et al. [Phys. At. Nucl. 67, 1884, (2004)] show that the assigned γ-ray decay of this state does not occur at a level consistent with known properties of inelastic scattering. In the present work the 56 Fe(n,n ' γ) reaction was used to populate excited states in 56 Fe. Neutrons in the energy range from 1 to 250 MeV were provided by the pulsed neutron source of the Los Alamos Neutron Science Center's WNR facility. Deexciting γ rays were detected with the GEANIE spectrometer, a Compton suppressed array of 26 Ge detectors. The γ-γ data obtained with GEANIE were used to establish coincidence relations between transitions. All previously reported levels up to E x =3.6 MeV excitation energy were observed except for the 3.076 MeV (3 - ) level. The 991- and 2229-keV transitions, previously reported to deexcite this level, were not observed in the γ-γ coincidence data obtained in the present experiment. The present work supports the assignment of the 4509.6 keV level as the first 3 - excited state in 56 Fe by observation of two previously known transitions deexciting this state.

The 9Be(d,n)10B reaction as a source of polarized neutrons from a low energy accelerator

International Nuclear Information System (INIS)

Bains, B.S.; Galloway, R.B.

1977-01-01

The 9 Be(d,n) 10 B reaction leading to the ground state of 10 B is found to provide a neutron beam with a polarization of 0.35 +- 0.06 at a reaction angle of 45 0 to a 400 keV deuteron beam. The suitability of such a polarized 4.5 MeV neutron beam for elastic scattering experiments is discussed. The polarization of the neutrons leading to the first excited state of 10 B is found to be - 0.08 +- 0.07 under the same conditions. (Auth.)

Interface influence on the properties of Co{sub 90}Fe{sub 10} films on soft magnetic underlayers – Magnetostrictive and Mössbauer spectrometry studies

Energy Technology Data Exchange (ETDEWEB)

Szumiata, Tadeusz, E-mail: t.szumiata@uthrad.pl [Department of Physics, Faculty of Mechanical Engineering, University of Technology and Humanities in Radom, 54 Krasickiego Street, 26-600 Radom (Poland); Gzik-Szumiata, Małgorzata; Brzózka, Katarzyna; Górka, Bogumił; Gawroński, Michał [Department of Physics, Faculty of Mechanical Engineering, University of Technology and Humanities in Radom, 54 Krasickiego Street, 26-600 Radom (Poland); Caruana Finkel, Anastasia; Reeves-McLaren, Nik; Morley, Nicola A. [Department of Materials Science and Engineering, University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)

2016-03-01

The main aim of the work was to show the correlation between magnetostrictive properties and microstructure of 25 nm thick Co{sub 90}Fe{sub 10} films deposited on soft magnetic underlayers. A special attention was paid to the role of the interface region. In the case of Co{sub 90}Fe{sub 10} on 25 nm and 35 nm thick METGLAS underlayers one can resolve in conversion electron Mössbauer spectra two hyperfine field distributions (high-field and medium-field ones) corresponding to both constituents of bilayers. Analogical distributions describe the spectra of Co{sub 90}Fe{sub 10} on 25 nm and 35 nm thick Ni{sub 81}Fe{sub 19} underlayers, however an additional low-field, smeared component has been observed. It has been attributed to the interface layer (of partially disordered structure) between magnetostrictive layer and soft magnetic layer. Such interpretation is backed up by the obtained strong correlation between mean hyperfine field value and magnetostriction constant of the films. The investigated bilayers are good candidates for MRAM devices. - Highlights: • We investigate Co–Fe thin films on the soft magnetic underlayers. • We measured magnetostriction and collected conversion electron Mössbauer spectra. • In the case of Permalloy underlayer a rapid drop of magnetostriction was observed. • Strong correlation between magnetostriction and hyperfine fields was shown. • Our results point to the essential role of the Co–Fe/underlayer interface.

Structure and Stability of GeAun, n = 1-10 clusters: A Density Functional Study

International Nuclear Information System (INIS)

Priyanka,; Dharamvir, Keya; Sharma, Hitesh

2011-01-01

The structures of Germanium doped gold clusters GeAu n (n = 1-10) have been investigated using ab initio calculations based on density functional theory (DFT). We have obtained ground state geometries of GeAu n clusters and have it compared with Silicon doped gold clusters and pure gold clusters. The ground state geometries of the GeAu n clusters show patterns similar to silicon doped gold clusters except for n = 5, 6 and 9. The introduction of germanium atom increases the binding energy of gold clusters. The binding energy per atom of germanium doped cluster is smaller than the corresponding silicon doped gold cluster. The HUMO-LOMO gap for Au n Ge clusters have been found to vary between 0.46 eV-2.09 eV. The mullikan charge analysis indicates that charge of order of 0.1e always transfers from germanium atom to gold atom.

An extreme Fe II emitter the narrow line quasar PHL 1092

CERN Document Server

Bergeron, J

1980-01-01

A search for Fe II emission in a sample of radio-quiet quasars has revealed the outstanding properties of PHL 1092. Intense Fe II lines dominate the entire spectrum, and the Fe II UV multiplets are nearly as strong as the optical ones. In contrast the extreme weakness of the Balmer and Mg II lines is striking. For the first time, Fe I lines are identified in an extra-galactic object. The lines are narrow, with a FWHM of 1300 km s/sup -1/. The presence of Fe II UV lines and Fe I lines from the ground state requires moderate column densities. However Fe/sup 0/ can exist only in a region completely shielded from the UV continuum. The weakness of Mg II and H beta relative to Fe II lines is best explained by their thermalization. The emitting region is of high electron density n/sub e/ approximately=10/sup 12/ cm/sup -3/, low temperature T approximately=10000K, and has an optical depth in the Fe II UV lines tau /sub UV/ approximately=10/sup 3/-10/sup 4/. It is speculated that for higher densities all the lines wou...

Effect of hydridation on structure of amorphous and amorphous-crystalline Fe40Ni40B20 and Co70Fe5Si15B10 bands

International Nuclear Information System (INIS)

Il'inskij, A.G.; Brovko, A.P.; Zelinskaya, G.M.; Kosenko, N.S.; Khristenko, T.M.; Kobzenko, G.F.; Shkola, A.A.

1988-01-01

The structure of amorphous and amorphous-crystaliline Fe 40 Ni 40 B 20 and Co 70 Fe 5 Si-1 5 B 10 alloys, exposed to hydridation at different temperatures, is studied by X-ray diffraction technique. The presence of crystalline constituent in amorphous bands was determined on DRON-3 device and by method of small-angle scattering. The experimental data obtained verify, that hydridation does not only prevent the formation of crystalline phases at annealing, but leads, as well, to disappearance of band crystalline constituent in case of its presence

Operational method of a ferroelectric (Fe)-NAND flash memory array

International Nuclear Information System (INIS)

Wang, Shouyu; Takahashi, Mitue; Li, Qiu-Hong; Sakai, Shigeki; Takeuchi, Ken

2009-01-01

Operations of arrayed ferroelectric (Fe)-NAND flash memory cells: erase, program and read were demonstrated for the first time using a small cell array of four word lines by two NAND strings. The memory cells and select-gate transistors were all n-channel Pt/SrBi 2 Ta 2 O 9 /Hf-Al-O/Si ferroelectric-gate field effect transistors. The erase was performed by applying 10 µs wide 7 V pulses to n- and p-wells. The program was performed by applying 10 µs wide 7 V pulses to selected word lines. Accumulated read currents of 51 programmed patterns in the Fe-NAND flash memory cell array successfully showed distribution of the two distinguishable '0' and '1' states. The margin between the two states became wider by applying a verification technique in programming a cell out of the eight. Retention times of bit-line currents were obtained over 33 h for both the '0' and '1' states in a program pattern

Poly[tetraaqua(μ6-9,10-dioxo-9,10-dihydroanthracene-1,4,5,8-tetracarboxylatodimanganese(II

Directory of Open Access Journals (Sweden)

Rui Xu

2012-07-01

Full Text Available The title complex, [Mn2(C18H4O10(H2O4]n, was synthesized from manganese(II chloride tetrahydrate and 9,10-dioxo-9,10-dihydroanthracene-1,4,5,8-tetracarboxylic acid (H4AQTC in water. The anthraquinone unit is located about a crystallographic center of inversion. Each asymmetric unit therefore contains one MnII atom, two water ligands and one half AQTC4− anion. The MnII atom is coordinated in a distorted octahedral geometry by four O atoms from three AQTC4− ligands and two water O atoms. Two of the carboxylate groups coordinate one MnII atom in a chelating mode, whereas the others each coordinate two MnII atoms. Each AQTC4− tetra-anion therefore coordinates six different MnII ions and, as a result, a three-dimensional coordination polymer is formed. O—H...O hydrogen bonds, some of them bifurcated, between water ligands and neighboring water or anthraquinone ligands are observed in the crystal structure.

Quantization of anomaly coefficients in 6D $\\mathcal{N}=(1,0)$ supergravity

OpenAIRE

Monnier, Samuel; Moore, Gregory W.; Park, Daniel S.

2017-01-01

We obtain new constraints on the anomaly coefficients of 6D $\\mathcal{N}=(1,0)$ supergravity theories using local and global anomaly cancellation conditions. We show how these constraints can be strengthened if we assume that the theory is well-defined on any spin space-time with an arbitrary gauge bundle. We distinguish the constraints depending on the gauge algebra only from those depending on the global structure of the gauge group. Our main constraint states that the coefficients of the a...

Application of ''elektronika 10-10'' electron linac for food irradiation

International Nuclear Information System (INIS)

Migdal, W.; Maciszewski, W.; Gryzlow, A.

1995-01-01

The industrial electron linac ''Elektronica 10-10'' has been installed in Experimental Plant for Food Irradiation (INCT) in 1990. The accelerator is a prototype unit, prior the use for food treatment a period of optimization was involved in its experimental operation during 1993. The accelerator is capable to produce scanned beam of electrons with the energy 10 MeV and beam power of 10 kW. Radiation dose at minimal conveyer speed of 0.25 m/min reaches 50 kGy. The role of the plant is to promote food irradiation in Poland. (Author)

26 CFR 1.852-10 - Distributions in redemption of interests in unit investment trusts.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Distributions in redemption of interests in unit investment trusts. 1.852-10 Section 1.852-10 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Regulated Investment Companies and Real Estate...

Study on adsorption of 99Tc on Fe, Fe2O3 and Fe3O4

International Nuclear Information System (INIS)

Liu Dejun; Fan Xianhua; Zhang Yingjie; Yao Jun; Zhou Duo; Wang Yong

2004-01-01

The absorption behavior of 99 Tc on Fe, Fe 2 O 3 and Fe 3 O 4 powders from aqueous 99 TcO 4 - solutions is studied by batch method in atmospheric conditions. After the adsorption reaches equilibrium, the valence state of 99 Tc in the aqueous solution is examined by extraction with tetraphenylarsonium chloride. The experimental results show that the adsorption ratio of 99 Tc on iron powders decreases with the increase of pH (in the range of 5-8) and of CO 3 2- concentration (in the range of 1 x 10 -8 -1 x 10 -2 mol/L). In opposite, the two factors have no significant influence on the absorption of 99 Tc on both Fe 2 O 3 and Fe 3 O 4 powders. The adsorption isotherms of 99 TcO 4 - on Fe, Fe 2 O 3 and Fe 3 O 4 powders can be well described by the Freundlich's equation. The major valence state of 99 Tc is deduced to be Tc(IV) when iron powders is used as the absorbent. In the case of Fe 2 O 3 or Fe 3 O 4 as an absorbent, the 99 Tc remains as the TcO 4 - form

2 CFR 3513.10 - What does this part do?

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false What does this part do? 3513.10 Section 3513.10 Grants and Agreements Federal Agency Regulations for Grants and Agreements EXPORT-IMPORT BANK OF... supplemented by this part, as the Export Import Bank of the United States (Ex-Im Bank) policies and procedures...

Observation of non-statistical structures in the excitation function of the reaction 10B(14N,12C)12C under extreme forward angles

International Nuclear Information System (INIS)

Klauss, E.U.

1984-01-01

In the present thesis the excitation functions of the reaction 10 B( 14 N, 12 C) 12 C to the ground states, the first excited state at 4.43 MeV (Jsup(π) = 2 1 + ) of a 12 C residual nucleus, and to the double excitation of ejectile and residue nucleus to the 4.43 state are studied. The measurements were performed in an energy range 13MeV 14 N) 0 (in the c.m. system). By a fitting to elastic scattering data the optical potential for 10 B+ 14 N was determined. With this potential it was tried by means of Hauser-Feshbach calculations to calculate the cross sections of the reaction 10 B( 14 N, 12 C) 12 C. The strong 16 + resonance and indications of 18 + in the excitation function of the reaction 10 B( 14 N, 12 Csub(g.s.)) 12 Csub(g.s.) should be pronounced. An unexpected large cross section was observed in the reaction 10 B( 14 N, 12 Csub(g.s.)) 12 C(4 1 + ). This is considered as a further indication to the strong contribution of a direct process. (orig./HSI) [de

Latin America and the United States: What Do United States History Textbooks Tell Us?

Science.gov (United States)

Fleming, Dan B.

1982-01-01

Evaluates how U.S.-Latin American relations are presented in high school U.S. history textbooks. An examination of 10 textbooks published between 1977-81 revealed inadequate coverage of Latin American cultural diversity and United States foreign policy from the Latin American perspective. (AM)

The elastic scattering of 14N by 10B

International Nuclear Information System (INIS)

Takai, H.

1986-01-01

The elastic scattering 10 B( 14 N, 14 N) 10 B was studied for four incident energies: 38.1, 42.0, 46.0 and 50.0 MeV. The angular distributions for these energies were determined in the center of mass frame from 16 0 to 176 0 with the introduction of target nucleus recoil detection techniques in a magnetic spectrograph with gas position sensitive detectors and in a scattering chamber with an Σ-ΔΣ detection system. For the forward angles, the angular distributions are well described by the optical model. For the backward angles, up to 160 0 , a satisfactory description is obtained by the elastic transfer analysis; for larger angles an accentuated deviation id observed. (author) [pt

Columnar grain growth of FePt(L10) thin films

International Nuclear Information System (INIS)

Yang En; Ho Hoan; Laughlin, David E.; Zhu Jiangang

2012-01-01

An experimental approach for obtaining perpendicular FePt-SiOx thin films with a large height to diameter ratio FePt(L1 0 ) columnar grains is presented in this work. The microstructure for FePt-SiOx composite thin films as a function of oxide volume fraction, substrate temperature, and film thickness is studied by plan view and cross section TEM. The relations between processing, microstructure, epitaxial texture, and magnetic properties are discussed. By tuning the thickness of the magnetic layer and the volume fraction of oxide in the film at a sputtering temperature of 410 deg. C, a 16 nm thick perpendicular FePt film with ∼8 nm diameter of FePt grains was obtained. The height to diameter ratio of the FePt grains was as large as 2. Ordering at lower temperature can be achieved by introducing a Ag sacrificial layer.

78 FR 6188 - Federal Acquisition Regulation; Free Trade Agreement-Colombia

Science.gov (United States)

2013-01-29

... Promotion Agreement. This Trade Promotion Agreement is a free trade agreement (FTA) that provides for... 77 FR 27548 on May 10, 2012, to implement the United States-Colombia Trade Promotion Agreement... and safety effects, distributive impacts, and equity). E.O. 13563 emphasizes the importance of...

37 CFR 10.65 - Limiting business relations with a client.

Science.gov (United States)

2010-07-01

... with a client. 10.65 Section 10.65 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND... a client. A practitioner shall not enter into a business transaction with a client if they have differing interests therein and if the client expects the practitioner to exercise professional judgment...

Impact of ultrafast demagnetization process on magnetization reversal in L10 FePt revealed using double laser pulse excitation

Science.gov (United States)

Shi, J. Y.; Tang, M.; Zhang, Z.; Ma, L.; Sun, L.; Zhou, C.; Hu, X. F.; Zheng, Z.; Shen, L. Q.; Zhou, S. M.; Wu, Y. Z.; Chen, L. Y.; Zhao, H. B.

2018-02-01

Ultrafast laser induced magnetization reversal in L10 FePt films with high perpendicular magnetic anisotropy was investigated using single- and double-pulse excitations. Single-pulse excitation beyond 10 mJ cm-2 caused magnetization (M) reversal at the applied fields much smaller than the static coercivity of the films. For double-pulse excitation, both coercivity reduction and reversal percentage showed a rapid and large decrease with the increasing time interval (Δt) of the two pulses in the range of 0-2 ps. In this Δt range, the maximum demagnetization (ΔMp) was also strongly attenuated, whereas the integrated demagnetization signals over more than 10 ps, corresponding to the average lattice heat effect, showed little change. These results indicate that laser induced M reversal in FePt films critically relies on ΔMp. Because ΔMp is determined by spin temperature, which is higher than lattice temperature, utilizing an ultrafast laser instead of a continuous-wave laser in laser-assisted M reversal may reduce the overall deposited energy and increase the speed of recording. The effective control of M reversal by slightly tuning the time delay of two laser pulses may also be useful for ultrafast spin manipulation.

Measurement of direct currents of under 10-10 ampere and of resistances of 1012 Ω for a direct current

International Nuclear Information System (INIS)

Vagner, J.

1965-01-01

Measurement of weak direct currents by Townsend's method using a vibrating condenser electrometer. Development of a current generator giving a pico-ampere independently of the resistance of the circuit used. Development of generators giving currents which may be adjusted continuously and exactly (0.1 to 1 pico-ampere, 1 to 10 pico-amperes, 10 to 100 pico-amperes). Measurement of very high resistances (10 12 Ω) by three different methods. Graphs are made by plotting the value of the resistance against the potential difference applied across it (from 50 milli-volts to 50 volts). Two methods use adjustable current generators and the third is applicable to the measurement of resistances of between 10 7 and 10 13 Ω using a series of condensers ranging from 50 pico-farads to 10 micro-farads. The accuracy of the measurements is between 0. 5 and 1 per cent. (author) [fr

76 FR 53494 - In the Matter of United States Enrichment Corporation; Paducah Gaseous Enrichment Plant...

Science.gov (United States)

2011-08-26

... be filed in accordance with the NRC E-Filing rule (72 FR 49139, August 28, 2007). The E-Filing... the procedural requirements of E-Filing, at least ten (10) days prior to the filing deadline, the... the NRC in accordance with the E-Filing rule, the participant must file the document using the NRC's...

Criminality Among Rural Stimulant Users in the United States

OpenAIRE

Oser, Carrie; Leukefeld, Carl; Staton-Tindall, Michele; Duvall, Jamieson; Garrity, Thomas; Stoops, William; Falck, Russel; Wang, Jichuan; Carlson, Robert; Sexton, Rocky; Wright, Patricia; Booth, Brenda

2011-01-01

Despite the increase in media attention on “meth cooking” in rural areas of the United States, little is known about rural stimulant use, particularly the criminality associated with stimulant use. Data were collected from community stimulant users in rural Ohio, Arkansas, and Kentucky (N=709). Findings from three logistic regression models indicate that younger stimulant users (x =32.55, SD = 10.35), those with more convictions, and those who used crack frequently were significantly more lik...

Unusual Synthetic Pathway for an {Fe(NO)₂}⁹ Dinitrosyl Iron Complex (DNIC) and Insight into DNIC Electronic Structure via Nuclear Resonance Vibrational Spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Speelman, Amy L.; Zhang, Bo; Silakov, Alexey; Skodje, Kelsey M.; Alp, E. Ercan; Zhao, Jiyong; Hu, Michael Y.; Kim, Eunsuk; Krebs, Karsten; Lehnert, Nicolai

2016-06-06

Dinitrosyl iron complexes (DNICs) are among the most abundant NO-derived cellular species. Monomeric DNICs can exist in the {Fe(NO)₂}⁹ or {Fe(NO)₂}¹⁰ oxidation state (in the Enemark -Feltham notation). However, experimental studies of analogous DNICs in both oxidation states are rare, which prevents a thorough understanding of the di ff erences in the electronic structures of these species. Here, the {Fe(NO)₂}⁹ DNIC [Fe(dmp)(NO)₂](OTf) ( 1 ; dmp = 2,9-dimethyl-1,10- phenanthroline) is synthesized from a ferrous precursor via an unusual pathway, involving disproportionation of an {FeNO}⁷ complex to yield the {Fe(NO)₂}⁹ DNIC and a ferric species, which is subsequently reduced by NO gas to generate a ferrous complex that re-enters the reaction cycle. In contrast to most {Fe(NO)₂}⁹ DNICs with neutral N-donor ligands, 1 exhibits high solution stability and can be characterized structurally and spectroscopically. Reduction of 1 yields the corresponding {Fe(NO)₂}¹⁰ DNIC [Fe(dmp)(NO)₂](2). The Mo ssbauer isomer shift of 2 is 0.08 mm/s smaller than that of 1 , which indicates that the iron center is slightly more oxidized in the reduced complex. The nuclear resonance vibrational spectra (NRVS) of 1 and 2 are distinct and provide direct experimental insight into di ff erences in bonding in these complexes. In particular, the symmetric out-of-plane Fe -N - O bending mode is shifted to higher energy by 188 cm^-1 in 2 in comparison to 1 . Using quantum chemistry centered normal coordinate analysis (QCC-NCA), this is shown to arise from an increase in Fe - NO bond order and a sti ff ening of the Fe(NO)₂ unit upon reduction of 1 to 2 . DFT calculations demonstrate that the changes in bonding arise from an iron- centered reduction which leads to a distinct increase in Fe - NO π -back-bonding in

49 CFR 835.10 - Testimony in Federal, State, or local criminal investigations and other proceedings.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Testimony in Federal, State, or local criminal investigations and other proceedings. 835.10 Section 835.10 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD TESTIMONY OF BOARD EMPLOYEES § 835.10 Testimony in Federal, State, or local crimina...

The unbound isotopes He-9,He-10

CERN Document Server

Jonson, B; Cortina-Gil, D; Simon, H; Emling, H; Nyman, G; Nilsson, T; Johansson, H T; Borge, M J G; Paschalis, S; Muenzenberg, G; Zhukov, M V; Weick, H; Pramanik, U Datta; LeBleis, T; Meister, M; Reifarth, R; Chulkov, L V; Lantz, M; Riisager, K; Mahata, K; Suemmerer, K; Langer, C; Chatillon, A; Richter, A; Kulessa, R; Palit, R; Aksyutina, Yu; Geissel, H; Aumann, T; Prokopowicz, W; Forssen, C; Ickert, G; Fynbo, H O U; Tengblad, O; Boretzky, K

2010-01-01

The unbound nuclei He-9 and He-10 have been produced in proton-knockout reactions from a 280 MeV/u Li-11 beam impinging on a liquid hydrogen target at the ALADIN-LAND setup at GSI. Information on their nuclear structure has been obtained from the relative-energy spectra, He-8 + n and He-8 + 2n, employing reaction models incorporating the structure of Li-11. The (8H)e + n relative-energy spectrum is dominated by a strong peak-like structure at low energy, which may be interpreted within the effective-range approximation as the result of an s-wave interaction with a neutron scattering length of -3.17(66) fm. This spectrum also shows evidence for resonance states at 1.33(8) MeV and at 2.4 MeV above the He-8 + n threshold. It is argued that the s-state might not be the He-9 ground state. For He-8 + n + n, the analysis of the relative-energy spectrum gives two alternative possibilities for an interpretation: either a narrow resonance at 1.42(10) MeV (Gamma = 1.11(76) MeV) superimposed on a correlated background, o...

A 10-Fr ultrasound catheter with integrated micromotor for 4-D intracardiac echocardiography.

Science.gov (United States)

Lee, Warren; Griffin, Weston; Wildes, Douglas; Buckley, Donald; Topka, Terry; Chodakauskas, Thaddeus; Langer, Mark; Calisti, Serge; Bergstøl, Svein; Malacrida, Jean-Pierre; Lanteri, Frédéric; Maffre, Jennifer; McDaniel, Ben; Shivkumar, Kalyanam; Cummings, Jennifer; Callans, David; Silvestry, Frank; Packer, Douglas

2011-07-01

We developed prototype real-time 3-D intracardiac echocardiography catheters with integrated micromotors, allowing internal oscillation of a low-profile 64-element, 6.2-MHz phased-array transducer in the elevation direction. Components were designed to facilitate rotation of the array, including a low-torque flexible transducer interconnect and miniature fixtures for the transducer and micromotor. The catheter tip prototypes were integrated with two-way deflectable 10-Fr catheters and used in in vivo animal testing at multiple facilities. The 4-D ICE catheters were capable of imaging a 90° azimuth by up to 180° elevation field of view. Volume rates ranged from 1 vol/sec (180° elevation) to approximately 10 vol/sec (60° elevation). We successfully imaged electrophysiology catheters, atrial septal puncture procedures, and detailed cardiac anatomy. The elevation oscillation enabled 3-D visualization of devices and anatomy, providing new clinical information and perspective not possible with current 2-D imaging catheters.

Characterization of High Dose Mn, Fe, and Ni implantation into p-GaN

CERN Document Server

Pearton, S J; Thaler, G; Abernathy, C R; Theodoropoulou, N; Hebard, A F; Chu, S N G; Wilson, R G; Zavada, J M; Polyakov, A Y; Osinsky, A V; Norris, P E; Chow, P P; Wowchack, A M; Hove, J M V; Park, Y D

2002-01-01

The magnetization of p-GaN or p-AlGaN/GaN superlattices was measured after implantation with high doses (3-5x10 sup 1 sup 6 cm sup - sup 2) of Mn, Fe, or Ni and subsequent annealing at 700-1000 deg. C. The samples showed ferromagnetic contributions below temperatures ranging from 190-250 K for Mn to 45-185 K for Ni and 80-250 K for Fe. The use of superlattices to enhance the hole concentration did not produce any change in ferromagnetic ordering temperature. No secondary phase formation was observed by x-ray diffraction, transmission electron microscopy, or selected area diffraction pattern analysis for the doses we employed.

Fluorescence quenching of N,N-bis(2,5-di-tert-butylphenyl)-3,4:9,10-perylenebis(dicarboximide) (DBPI) by silver nanoparticles

Energy Technology Data Exchange (ETDEWEB)

El-Daly, Samy A., E-mail: samyeldaly@yahoo.com [Chemistry Department, Faculty of Science, King Abdulaziz University, PO Box 80203, Jeddah 21589 (Saudi Arabia); Chemistry Department, Faculty of Science, Tanta University, Tanta 2173 (Egypt); Rahman, Mohammed M. [Chemistry Department, Faculty of Science, King Abdulaziz University, PO Box 80203, Jeddah 21589 (Saudi Arabia); Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, PO Box 80203, Jeddah 21589 (Saudi Arabia); Alamry, Kahlid A. [Chemistry Department, Faculty of Science, King Abdulaziz University, PO Box 80203, Jeddah 21589 (Saudi Arabia); Asiri, Abdullah M. [Chemistry Department, Faculty of Science, King Abdulaziz University, PO Box 80203, Jeddah 21589 (Saudi Arabia); Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, PO Box 80203, Jeddah 21589 (Saudi Arabia)

2014-04-15

The interaction of a perylene derivative namely N,N-bis(2,5-di-tert-butylphenyl)-3,4:9,10-perylenebis(dicarboximide) (DBPI) with colloidal silver nanoparticles (AgNPs) was studied in ethanol and ethylene glycol using steady state fluorescence quenching measurements. The Stern–Volmer quenching rate constant (K{sub sv}) was calculated as 4.03×10{sup 9} and 29.14×10{sup 9} M{sup −1} in ethanol and ethylene glycol, respectively. From fluorescence quenching data, static quenching and energy transfer play a major role in the fluorescence quenching of DBPI by AgNPs. The apparent association constant (k{sub app}) was calculated as 1.26×10{sup 8} M{sup −1} in EtOH and 1.83×10{sup 9} M{sup −1} in ethylene glycol. Due to potential AgNPs interaction with DBPI, the average AgNPs size is increased slightly from ∼37.1 nm (As-prepared) to 48.9 nm. -- Highlights: • Fluorescence quenching of photostable DBPI by AgNPs. • Static quenching mechanism of interaction between DBPI and AgNPs. • Enhancement of fluorescence quenching of DBPI in ethylene glycol.

Decacarbonyl[μ4-(ethane-1,2-diyldinitrilotetrakis(methanethiolato]bis(triphenylphosphanetetrairon(2 Fe—Fe

Directory of Open Access Journals (Sweden)

Wei-Ming Gao

2012-02-01

Full Text Available In the title compound, [Fe4(C6H12N2S4(C18H15P2(CO10], the unit cell contains one molecule, which exhibits a crystallographically imposed center of symmetry. The independent Fe2S2 fragment [Fe—Fe = 2.527 (1 Å] is in a butterfly conformation, and each Fe atom displays a pseudo-square-pyramidal coordination geometry. The phosphane group occupies an apical position [Fe—P = 2.2670 (14 Å]. In the crystal, weak intermolecular C—H...O hydrogen bonds link the molecules into chains along [110].

10 CFR 440.1 - Purpose and scope.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Purpose and scope. 440.1 Section 440.1 Energy DEPARTMENT... scope. This part implements a weatherization assistance program to increase the energy efficiency of... with children, high residential energy users, and households with high energy burden. [65 FR 77217, Dec...

75 FR 25925 - United States Mint

Science.gov (United States)

2010-05-10

... Committee May 25, 2010 Public Meeting. SUMMARY: Pursuant to United States Code, Title 31, section 5135(b)(8... scheduled for May 25, 2010. Date: May 25, 2010. Time: 9 a.m. to 12 p.m. Location: 8th Floor Board Room, United States Mint, 801 9th Street, NW., Washington, DC 20220. Subject: Review and discuss obverse and...

19 CFR 10.602 - Packing materials and containers for shipment.

Science.gov (United States)

2010-04-01

...-Central America-United States Free Trade Agreement Rules of Origin § 10.602 Packing materials and... regional value content calculation. Packing materials and containers for shipment, as defined in § 10.593(m) of this subpart, are to be disregarded in determining the regional value content of a good imported...